ESA Sample Fetch Rover: Heritage and Way Forward

NASA Astrophysics Data System (ADS)

Duvet, L.; Beyer, F.; Delfa, J.; Zekri, E.

2018-04-01

The Sample Fetch Rover (SFR) is one of the key elements of the Mars Sample Return (MSR) campaign architecture. We will present the SFR heritage as well as a way forward identified to address this engineering challenge.

Octopus arm movements under constrained conditions: adaptation, modification and plasticity of motor primitives.

PubMed

Richter, Jonas N; Hochner, Binyamin; Kuba, Michael J

2015-04-01

The motor control of the eight highly flexible arms of the common octopus (Octopus vulgaris) has been the focus of several recent studies. Our study is the first to manage to introduce a physical constraint to an octopus arm and investigate the adaptability of stereotypical bend propagation in reaching movements and the pseudo-limb articulation during fetching. Subjects (N=6) were placed inside a transparent Perspex box with a hole at the center that allowed the insertion of a single arm. Animals had to reach out through the hole toward a target, to retrieve a food reward and fetch it. All subjects successfully adjusted their movements to the constraint without an adaptation phase. During reaching tasks, the animals showed two movement strategies: stereotypical bend propagation reachings, which were established at the hole of the Perspex box and variant waving-like movements that showed no bend propagations. During fetching movements, no complete pseudo-joint fetching was observed outside the box and subjects pulled their arms through the hole in a pull-in like movement. Our findings show that there is some flexibility in the octopus motor system to adapt to a novel situation. However, at present, it seems that these changes are more an effect of random choices between different alternative motor programs, without showing clear learning effects in the choice between the alternatives. Interestingly, animals were able to adapt the fetching movements to the physical constraint, or as an alternative explanation, they could switch the motor primitive fetching to a different motor primitive 'arm pulling'. © 2015. Published by The Company of Biologists Ltd.

MSR Fetch Rover Capability Development at the Canadian Space Agency

NASA Astrophysics Data System (ADS)

Picard, M.; Hipkin, V.; Gingras, D.; Allard, P.; Lamarche, T.; Rocheleau, S. G.; Gemme, S.

2018-04-01

Describes Fetch Rover technology testing during CSA's 2016 Mars Sample Return Analogue Deployment which demonstrated autonomous navigation to 'cache depots' of M-2020-like sample tubes, acquisition of six such tubes, and transfer to a MAV mock up.

PubSearch and PubFetch: a simple management system for semiautomated retrieval and annotation of biological information from the literature.

PubMed

Yoo, Danny; Xu, Iris; Berardini, Tanya Z; Rhee, Seung Yon; Narayanasamy, Vijay; Twigger, Simon

2006-03-01

For most systems in biology, a large body of literature exists that describes the complexity of the system based on experimental results. Manual review of this literature to extract targeted information into biological databases is difficult and time consuming. To address this problem, we developed PubSearch and PubFetch, which store literature, keyword, and gene information in a relational database, index the literature with keywords and gene names, and provide a Web user interface for annotating the genes from experimental data found in the associated literature. A set of protocols is provided in this unit for installing, populating, running, and using PubSearch and PubFetch. In addition, we provide support protocols for performing controlled vocabulary annotations. Intended users of PubSearch and PubFetch are database curators and biology researchers interested in tracking the literature and capturing information about genes of interest in a more effective way than with conventional spreadsheets and lab notebooks.

Effects of Fetch on Turbulent Flow and Pollutant Dispersion Within a Cubical Canopy

NASA Astrophysics Data System (ADS)

Michioka, Takenobu; Takimoto, Hiroshi; Ono, Hiroki; Sato, Ayumu

2018-03-01

The effects of fetch on turbulent flow and pollutant dispersion within a canopy formed by regularly-spaced cubical objects is investigated using large-eddy simulation. Six tracer gases are simultaneously released from a ground-level continuous pollutant line source placed parallel to the spanwise axis at the first, second, third, fifth, seventh and tenth rows. Beyond the seventh row, the standard deviations of the fluctuations in the velocity components and the Reynolds shear stresses reach nearly equivalent states. Low-frequency turbulent flow is generated near the bottom surface around the first row and develops as the fetch increases. The turbulent flow eventually passes through the canopy at a near-constant interval. The mean concentration within the canopy reaches a near-constant value beyond the seventh row. In the first and second rows, narrow coherent structures frequently affect the pollutant escape from the top of the canopy. These structures increase in width as the fetch increases, and they mainly affect the removal of pollutants from the canopy.

Fetch-Trapping in Hurricane Isabel

NASA Astrophysics Data System (ADS)

Pearse, A. J.; Hanson, J. L.

2005-12-01

Hurricane Isabel made landfall near Drum Inlet on the Outer Banks of North Carolina on September 18, 2003, and caused extensive monetary and coastal damage. Storm surge and battering waves were a primary cause of damage, as in most hurricanes. Data collected at the US Army Corps of Engineers Field Research Facility (FRF) in Duck, NC, the National Data Buoy Center (NDBC), and the Coastal Data Information Program (CDIP) suggest that the waves generated by Hurricane Isabel were larger and had longer periods than would be suggested by a traditional semi-empirical wave growth model with similar fetch and wind speed values. It is likely that this enhanced growth was due to the trapping of storm waves within the moving fetch of the hurricane. The purpose of this study was to empirically confirm the enhancement and to identify the degree of fetch-trapping that occurred. Directional wave spectra from 577 individual wave records were collected from buoys in three locations: CDIP station 078 in King's Bay, GA, the FRF Waverider in NC, and NDBC Station 44025 off Long Island, NY. A wave partitioning approach was used to isolate the individual swell components from the evolving wave field at each station. A backward raytrace along great-circle routes was employed to identify the intersection of each swell system with the official National Hurricane Center (NHC) Isabel track. This allowed matching each observed swell component with a generation time, storm translation speed, and peak wind speed. Wave period, rather than amplitude, was used in this study because amplitude is significantly affected by the bottom topography whereas period is conserved. Using the identified wind speeds and an average fetch of 200 km (approximated using NOAA wind field charts), the actual waves showed wave period enhancements up to 60% over predictions using the standard wave growth model. A variety of resonance criteria are applied to evaluate fetch trapping in Hurricane Isabel. The most enhanced wave periods were found to occur when the wave group speeds most closely matched the storm translation speeds, strongly suggesting that fetch trapping was an important mechanism for wave growth in Isabel.

The effect of wind waves on spring-neap variations in sediment transport in two meso-tidal estuarine basins with contrasting fetch

NASA Astrophysics Data System (ADS)

Hunt, Stephen; Bryan, Karin R.; Mullarney, Julia C.

2017-03-01

Higher-energy episodic wind-waves can substantially modify estuarine morphology over short timescales which are superimposed on lower-energy but long-term tidal asymmetry effects. Theoretically, wind waves and tidal currents change the morphology through their combined influence on the asymmetry between bed shear stress, τmax, on the flood and ebb tide, although the relative contribution of such wind-wave events in shaping the long-term morphological evolution in real estuaries is not well known. If the rising tide reaches sufficiently high water depths, τmax decreases as water depth increases because of the depth attenuation of wave orbital velocities. However, this effect is opposed by the increase in τmax associated with the longer fetch occurring at high tide, which allows the generation of larger waves. Additionally, these effects are superimposed on the spring-neap variations in current associated with changes to tidal range. By comparing two mesotidal basins in the same dendritic estuary, one with a large fetch aligned with the prevailing wind direction and one with only a small fetch, we show that for a sufficiently large fetch even the small and frequently occurring wind events are able to create waves that are capable of changing the morphology ('morphologically significant'). Conversely, in the basin with reduced fetch, these waves are generated less frequently and therefore are of reduced morphological significance. Here, we find that although tidal current should be stronger during spring tides and alter morphology more, on average the reduced fetch and increased water depth during spring tides mean that the basin-averaged intertidal τmax is similar during both spring and neap tides. Moreover, in the presence of wind waves, the duration of slack water is reduced during neap tides relative to spring tides, resulting in a reduced chance for accretion during neap tides. Finally, τmax is lower in the subtidal channels during neaps than springs but of a similar magnitude over the intertidal areas, and so sediment is more likely to be advected from the intertidal regions during neap tides rather than springs. This spring-neap cycle in sediment transport potential is in sharp contrast to that found previously in microtidal wave-dominated environments, where spring tides are expected to enhance erosion.

U.S. Navy Global and Regional Wave Modeling

DTIC Science & Technology

2014-09-01

for par- allel processing (Wittmann, 2002), the open source policy of WW3, and WW3’ s accurate...burden estimate or any other aspect of this collection of information, including suggestions for reducing the burden, to the Department of Defense ...September 2014 57 which determine the fetch and duration available for generation of wave energy, and (2) the direction and distance of

Counting Dependence Predictors

DTIC Science & Technology

2008-05-02

sophisticated dependence predictors, such as Store Sets, have been tightly coupled to the fetch and ex- ecution streams, requiring global knowledge of...applicable to any architecture with distributed fetch and distributed memory banks, in which the comprehensive event completion knowledge needed by previous...adapted for Core Fusion [5] by giv- ing its steering management unit (SMU) the responsibilities of the controller core. While Ipek et al. describe how a

Tree-Level Hydrodynamic Approach for Improved Stomatal Conductance Parameterization

NASA Astrophysics Data System (ADS)

Mirfenderesgi, G.; Bohrer, G.; Matheny, A. M.; Ivanov, V. Y.

2014-12-01

The land-surface models do not mechanistically resolve hydrodynamic processes within the tree. The Finite-Elements Tree-Crown Hydrodynamics model version 2 (FETCH2) is based on the pervious FETCH model approach, but with finite difference numerics, and simplified single-beam conduit system. FETCH2 simulates water flow through the tree as a simplified system of porous media conduits. It explicitly resolves spatiotemporal hydraulic stresses throughout the tree's vertical extent that cannot be easily represented using other stomatal-conductance models. Empirical equations relate water potential at the stem to stomata conductance at leaves connected to the stem (through unresolved branches) at that height. While highly simplified, this approach bring some realism to the simulation of stomata conductance because the stomata can respond to stem water potential, rather than an assumed direct relationship with soil moisture, as is currently the case in almost all models. By enabling mechanistic simulation of hydrological traits, such as xylem conductivity, conductive area per DBH, vertical distribution of leaf area and maximal and minimal water content in the xylem, and their effect of the dynamics of water flow in the tree system, the FETCH2 modeling system enhanced our understanding of the role of hydraulic limitations on an experimental forest plot short-term water stresses that lead to tradeoffs between water and light availability for transpiring leaves in forest ecosystems. FETCH2 is particularly suitable to resolve the effects of structural differences between tree and species and size groups, and the consequences of differences in hydraulic strategies of different species. We leverage on a large dataset of sap flow from 60 trees of 4 species at our experimental plot at the University of Michigan Biological Station. Comparison of the sap flow and transpiration patterns in this site and an undisturbed control site shows significant difference in hydraulic strategies between species which affect their response to the disturbance. We used FETCH2 to conduct a sensitivity analysis of the total stand-level transpiration to the inter-specific differences in hydraulic strategies and used the results to reflect on the future trajectory of the forest, in terms of species composition and transpiration.

Aeolian sediment transport on a beach: Surface moisture, wind fetch, and mean transport

NASA Astrophysics Data System (ADS)

Bauer, B. O.; Davidson-Arnott, R. G. D.; Hesp, P. A.; Namikas, S. L.; Ollerhead, J.; Walker, I. J.

2009-04-01

Temporal and spatial changes in wind speed, wind direction, and moisture content are ubiquitous across sandy coastal beaches. Often these factors interact in unknown ways to create complexity that confounds our ability to model sediment transport at any point across the beach as well as our capacity to predict sediment delivery into the adjacent foredunes. This study was designed to measure wind flow and sediment transport over a beach and foredune at Greenwich Dunes, Prince Edward Island National Park, with the express purpose of addressing these complex interactions. Detailed measurements are reported for one stormy day, October 11, 2004, during which meteorological conditions were highly variable. Wind speed ranged from 4 ms - 1 to over 20 ms - 1 , wind direction was highly oblique varying between 60° and 85° from shore perpendicular, and moisture content of the sand surface ranged from a minimum of about 3% (by mass) to complete saturation depending on precipitation, tidal excursion, and storm surge that progressively inundated the beach. The data indicate that short-term variations (i.e., minutes to hours) in sediment transport across this beach arise predominantly because of short-term changes in wind speed, as is expected, but also because of variations in wind direction, precipitation intensity, and tide level. Even slight increases in wind speed are capable of driving more intense saltation events, but this relationship is mediated by other factors on this characteristically narrow beach. As the angle of wind approach becomes more oblique, the fetch distance increases and allows greater opportunity for the saltation system to evolve toward an equilibrium transport state before reaching the foredunes. Whether the theoretically-predicted maximum rate of transport is ever achieved depends on the character of the sand surface (e.g., grain size, slope, roughness, vegetation, moisture content) and on various attributes of the wind field (e.g., average wind speed, unsteadiness, approach angle, flow compression, boundary layer development). Moisture content is widely acknowledged as an important factor in controlling release of sediment from the beach surface. All other things being equal, the rate of sediment transport over a wet surface is lesser than over a dry surface. On this beach, the moisture effect has two important influences: (a) in a temporal sense, the rate of sediment transport typically decreases in association with rainfall and increases when surface drying takes place; and (b) in a spatio-temporal sense, shoreline excursions associated with nearshore processes (such as wave run-up, storm surge, and tidal excursions) have the effect of constraining the fetch geometry of the beach—i.e., narrowing the width of the beach. Because saturated sand surfaces, such as found in the swash zone, will only reluctantly yield sediments to aeolian entrainment, the available beach surface across which aeolian transport can occur becomes narrower as the sea progressively inundates the beach. Under these constrained conditions, the transport system begins to shut down unless wind angle becomes highly oblique (thereby increasing fetch distance). In this study, maximum sediment transport was usually measured on the mid-beach rather than the upper beach (i.e., closer to the foredunes). This unusual finding is likely because of internal boundary layer development across the beach, which yields a decrease in near-surface wind speed (and hence, transport capacity) in the landward direction. Although widely recognized in the fluid mechanics literature, this decrease in near-surface shear stress as a by-product of a developing boundary layer in the downwind direction has not been adequately investigated in the context of coastal aeolian geomorphology.

Tree level hydrodynamic approach for resolving aboveground water storage and stomatal conductance and modeling the effects of tree hydraulic strategy

DOE PAGES

Mirfenderesgi, Golnazalsadat; Bohrer, Gil; Matheny, Ashley M.; ...

2016-06-21

The finite difference ecosystem-scale tree crown hydrodynamics model version 2 (FETCH2) is a tree-scale hydrodynamic model of transpiration. The FETCH2 model employs a finite difference numerical methodology and a simplified single-beam conduit system to explicitly resolve xylem water potentials throughout the vertical extent of a tree. Empirical equations relate water potential within the stem to stomatal conductance of the leaves at each height throughout the crown. While highly simplified, this approach brings additional realism to the simulation of transpiration by linking stomatal responses to stem water potential rather than directly to soil moisture, as is currently the case in themore » majority of land surface models. FETCH2 accounts for plant hydraulic traits, such as the degree of anisohydric/isohydric response of stomata, maximal xylem conductivity, vertical distribution of leaf area, and maximal and minimal xylem water content. We used FETCH2 along with sap flow and eddy covariance data sets collected from a mixed plot of two genera (oak/pine) in Silas Little Experimental Forest, NJ, USA, to conduct an analysis of the intergeneric variation of hydraulic strategies and their effects on diurnal and seasonal transpiration dynamics. We define these strategies through the parameters that describe the genus level transpiration and xylem conductivity responses to changes in stem water potential. Here, our evaluation revealed that FETCH2 considerably improved the simulation of ecosystem transpiration and latent heat flux in comparison to more conventional models. In conclusion, a virtual experiment showed that the model was able to capture the effect of hydraulic strategies such as isohydric/anisohydric behavior on stomatal conductance under different soil-water availability conditions.« less

Tree level hydrodynamic approach for resolving aboveground water storage and stomatal conductance and modeling the effects of tree hydraulic strategy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mirfenderesgi, Golnazalsadat; Bohrer, Gil; Matheny, Ashley M.

The finite difference ecosystem-scale tree crown hydrodynamics model version 2 (FETCH2) is a tree-scale hydrodynamic model of transpiration. The FETCH2 model employs a finite difference numerical methodology and a simplified single-beam conduit system to explicitly resolve xylem water potentials throughout the vertical extent of a tree. Empirical equations relate water potential within the stem to stomatal conductance of the leaves at each height throughout the crown. While highly simplified, this approach brings additional realism to the simulation of transpiration by linking stomatal responses to stem water potential rather than directly to soil moisture, as is currently the case in themore » majority of land surface models. FETCH2 accounts for plant hydraulic traits, such as the degree of anisohydric/isohydric response of stomata, maximal xylem conductivity, vertical distribution of leaf area, and maximal and minimal xylem water content. We used FETCH2 along with sap flow and eddy covariance data sets collected from a mixed plot of two genera (oak/pine) in Silas Little Experimental Forest, NJ, USA, to conduct an analysis of the intergeneric variation of hydraulic strategies and their effects on diurnal and seasonal transpiration dynamics. We define these strategies through the parameters that describe the genus level transpiration and xylem conductivity responses to changes in stem water potential. Here, our evaluation revealed that FETCH2 considerably improved the simulation of ecosystem transpiration and latent heat flux in comparison to more conventional models. In conclusion, a virtual experiment showed that the model was able to capture the effect of hydraulic strategies such as isohydric/anisohydric behavior on stomatal conductance under different soil-water availability conditions.« less

Tree-Level Hydrodynamic Approach for Modeling Aboveground Water Storage and Stomatal Conductance Highlights the Effects of Tree Hydraulic Strategy

NASA Astrophysics Data System (ADS)

Mirfenderesgi, G.; Bohrer, G.; Matheny, A. M.; Fatichi, S.; Frasson, R. P. M.; Schafer, K. V.

2016-12-01

The Finite-difference Ecosystem-scale Tree-Crown Hydrodynamics model version 2 (FETCH2) is a novel tree-scale hydrodynamic model of transpiration. The FETCH2 model employs a finite difference numerical methodology and a simplified single-beam conduit system and simulates water flow through the tree as a continuum of porous media conduits. It explicitly resolves xylem water potential throughout the tree's vertical extent. Empirical equations relate water potential within the stem to stomatal conductance of the leaves at each height throughout the crown. While highly simplified, this approach brings additional realism to the simulation of transpiration by linking stomatal responses to stem water potential rather than directly to soil moisture, as is currently the case in the majority of land-surface models. FETCH2 accounts for plant hydraulic traits, such as the degree of anisohydric/isohydric response of stomata, maximal xylem conductivity, vertical distribution of leaf area, and maximal and minimal stemwater content. We used FETCH2 along with sap flow and eddy covariance data sets collected from a mixed plot of two genera (oak/pine) in Silas Little Experimental Forest, NJ, USA, to conduct an analysis of the inter-genera variation of hydraulic strategies and their effects on diurnal and seasonal transpiration dynamics. We define these strategies through the parameters that describe the genus-level transpiration and xylem conductivity responses to changes in stem water potential. A virtual experiment showed that the model was able to capture the effect of hydraulic strategies such as isohydric/anisohydric behavior on stomatal conductance under different soil-water availability conditions. Our evaluation revealed that FETCH2 considerably improved the simulation of ecosystem transpiration and latent heat flux than more conventional models.

Tree level hydrodynamic approach for resolving aboveground water storage and stomatal conductance and modeling the effects of tree hydraulic strategy

NASA Astrophysics Data System (ADS)

Mirfenderesgi, Golnazalsadat; Bohrer, Gil; Matheny, Ashley M.; Fatichi, Simone; de Moraes Frasson, Renato Prata; Schäfer, Karina V. R.

2016-07-01

The finite difference ecosystem-scale tree crown hydrodynamics model version 2 (FETCH2) is a tree-scale hydrodynamic model of transpiration. The FETCH2 model employs a finite difference numerical methodology and a simplified single-beam conduit system to explicitly resolve xylem water potentials throughout the vertical extent of a tree. Empirical equations relate water potential within the stem to stomatal conductance of the leaves at each height throughout the crown. While highly simplified, this approach brings additional realism to the simulation of transpiration by linking stomatal responses to stem water potential rather than directly to soil moisture, as is currently the case in the majority of land surface models. FETCH2 accounts for plant hydraulic traits, such as the degree of anisohydric/isohydric response of stomata, maximal xylem conductivity, vertical distribution of leaf area, and maximal and minimal xylem water content. We used FETCH2 along with sap flow and eddy covariance data sets collected from a mixed plot of two genera (oak/pine) in Silas Little Experimental Forest, NJ, USA, to conduct an analysis of the intergeneric variation of hydraulic strategies and their effects on diurnal and seasonal transpiration dynamics. We define these strategies through the parameters that describe the genus level transpiration and xylem conductivity responses to changes in stem water potential. Our evaluation revealed that FETCH2 considerably improved the simulation of ecosystem transpiration and latent heat flux in comparison to more conventional models. A virtual experiment showed that the model was able to capture the effect of hydraulic strategies such as isohydric/anisohydric behavior on stomatal conductance under different soil-water availability conditions.

Turbulent Structure Under Short Fetch Wind Waves

DTIC Science & Technology

2015-12-01

1970) developed the LFT utilizing the concurrent measurement of sea surface elevation (η) and the near surface velocities to isolate the wave...Layers and Air-Sea Transfer program by making very high spatial resolution profile measurements of the 3-D velocity field into the crest-trough...distribution is unlimited TURBULENT STRUCTURE UNDER SHORT FETCH WIND WAVES Michael J. Papa Lieutenant Commander, United States Navy B.S., United States Naval

Forward Scattering from Fetch-Limited and Swell-Contaminated Sea Surfaces

DTIC Science & Technology

1992-10-01

limited wind fields, and the global/re- Hasselman 5 et al. have proposed that a constant value for y gional deep water wave model7 ( DWAVE ) for surfaces gen...where it is difficult to define the Pierson-Moskowitz or JONSWAP descriptions, DWAVE fetch, the peak frequency of the observed spectrum can be...generating winds, the DWAVE model dependence of the spectrum on azimuthal variation, it is ex- has been employed. This model numerically calculates the

System for processing an encrypted instruction stream in hardware

DOE Office of Scientific and Technical Information (OSTI.GOV)

Griswold, Richard L.; Nickless, William K.; Conrad, Ryan C.

A system and method of processing an encrypted instruction stream in hardware is disclosed. Main memory stores the encrypted instruction stream and unencrypted data. A central processing unit (CPU) is operatively coupled to the main memory. A decryptor is operatively coupled to the main memory and located within the CPU. The decryptor decrypts the encrypted instruction stream upon receipt of an instruction fetch signal from a CPU core. Unencrypted data is passed through to the CPU core without decryption upon receipt of a data fetch signal.

Scaling Observations of Surface Waves in the Beaufort Sea

DTIC Science & Technology

2016-04-14

the treatment of wind input can be improved in partial ice cover using the ice concentration, where wave energy is a function of open water distance...drifting buoys during the 2014 open water season, are interpreted using open water distances determined from satellite ice products and wind forcing time...series measured in situ with the buoys. A significant portion of the wave observations were found to be limited by open water distance (fetch) when

Strategies for human-driven robot comprehension of spatial descriptions by older adults in a robot fetch task.

PubMed

Carlson, Laura; Skubic, Marjorie; Miller, Jared; Huo, Zhiyu; Alexenko, Tatiana

2014-07-01

This contribution presents a corpus of spatial descriptions and describes the development of a human-driven spatial language robot system for their comprehension. The domain of application is an eldercare setting in which an assistive robot is asked to "fetch" an object for an elderly resident based on a natural language spatial description given by the resident. In Part One, we describe a corpus of naturally occurring descriptions elicited from a group of older adults within a virtual 3D home that simulates the eldercare setting. We contrast descriptions elicited when participants offered descriptions to a human versus robot avatar, and under instructions to tell the addressee how to find the target versus where the target is. We summarize the key features of the spatial descriptions, including their dynamic versus static nature and the perspective adopted by the speaker. In Part Two, we discuss critical cognitive and perceptual processing capabilities necessary for the robot to establish a common ground with the human user and perform the "fetch" task. Based on the collected corpus, we focus here on resolving the perspective ambiguity and recognizing furniture items used as landmarks in the descriptions. Taken together, the work presented here offers the key building blocks of a robust system that takes as input natural spatial language descriptions and produces commands that drive the robot to successfully fetch objects within our eldercare scenario. Copyright © 2014 Cognitive Science Society, Inc.

Measurements of wind-waves under transient wind conditions.

NASA Astrophysics Data System (ADS)

Shemer, Lev; Zavadsky, Andrey

2015-11-01

Wind forcing in nature is always unsteady, resulting in a complicated evolution pattern that involves numerous time and space scales. In the present work, wind waves in a laboratory wind-wave flume are studied under unsteady forcing`. The variation of the surface elevation is measured by capacitance wave gauges, while the components of the instantaneous surface slope in across-wind and along-wind directions are determined by a regular or scanning laser slope gauge. The locations of the wave gauge and of the laser slope gauge are separated by few centimeters in across-wind direction. Instantaneous wind velocity was recorded simultaneously using Pitot tube. Measurements are performed at a number of fetches and for different patterns of wind velocity variation. For each case, at least 100 independent realizations were recorded for a given wind velocity variation pattern. The accumulated data sets allow calculating ensemble-averaged values of the measured parameters. Significant differences between the evolution patterns of the surface elevation and of the slope components were found. Wavelet analysis was applied to determine dominant wave frequency of the surface elevation and of the slope variation at each instant. Corresponding ensemble-averaged values acquired by different sensors were computed and compared. Analysis of the measured ensemble-averaged quantities at different fetches makes it possible to identify different stages in the wind-wave evolution and to estimate the appropriate time and length scales.

Dying for water.

PubMed

Yeboah-afari, A

1993-01-01

In Danchira village in Ghana for the last 5 years, women and children rise before dawn every day to fetch water from a tributary or the River Densu, which is 5 miles from the village. Diminished rainfall has dried the village's 3 ponds and bore-hole where the women and children used to fetch water. To exacerbate the water problem, the Ghana Water and Sewerage Corporation no longer comes to fill the huge water tank it brought to Danchira when water scarcity first occurred. The villagers could not afford to pay for the water. A 55-year-old mother of 5, Dede Aryehteye, takes her morning bath at the river. When she has dirty laundry, she cleans it in the river. She returns to the village around 8 am. She uses the next hour to filter the dark water 2 times with a device provided free of charge by the national Guinea Worm Eradication Programme to keep the larvae out of the water. Next she sort the water for 3 uses: drinking, household use, and evening bath. Dede then does other domestic chores. She would rather go to her cassava farm in the early morning when it is cool but has to fetch water instead. When she is not too tired and after finishing domestic chores, she goes to the farm. Water-fetching also exhausts the children and gets them to school rather late. Children make up the majority of the 500 people living in Danchira. Water scarcity forced most of the young villagers to flee to the cities. For example, Dede's 4 older children now live in Accra. The water scarcity keeps the farmers from growing maize, cassava, and vegetables.

Memory interface simulator: A computer design aid

NASA Technical Reports Server (NTRS)

Taylor, D. S.; Williams, T.; Weatherbee, J. E.

1972-01-01

Results are presented of a study conducted with a digital simulation model being used in the design of the Automatically Reconfigurable Modular Multiprocessor System (ARMMS), a candidate computer system for future manned and unmanned space missions. The model simulates the activity involved as instructions are fetched from random access memory for execution in one of the system central processing units. A series of model runs measured instruction execution time under various assumptions pertaining to the CPU's and the interface between the CPU's and RAM. Design tradeoffs are presented in the following areas: Bus widths, CPU microprogram read only memory cycle time, multiple instruction fetch, and instruction mix.

Experimental study of temporal evolution of waves under transient wind conditions

NASA Astrophysics Data System (ADS)

Zavadsky, Andrey; Shemer, Lev

2016-11-01

Temporal variation of the waves excited by nearly sudden wind forcing over an initially still water surface is studied in a small wind-wave flume at Tel Aviv University for variety of fetches and wind velocities. Simultaneous measurements of the surface elevation using a conventional capacitance wave-gauge and of the surface slope in along-wind and cross-wind directions by a laser slope gauge were performed. Variation with time of two components of instantaneous surface velocity was measured by particle tracking velocimetry. The size of the experimental facility and thus relatively short characteristic time scales of the phenomena under investigation, as well as an automated experimental procedure controlling the experiments made it possible to record a large amount of independent realizations for each wind-fetch condition. Sufficient data were accumulated to compute reliable ensemble averaged temporal variation of governing wave parameters. The essentially three-dimensional structure of wind-waves at all stages of evolution is demonstrated. The results obtained at each wind-fetch condition allowed to characterize the major stages of the evolution of the wind-wave field and to suggest a plausible scenario for the initial growth of the wind-waves.

New Insights on Coastal Foredune Growth: The Relative Contributions of Marine and Aeolian Processes

NASA Astrophysics Data System (ADS)

Cohn, Nicholas; Ruggiero, Peter; de Vries, Sierd; Kaminsky, George M.

2018-05-01

Coastal foredune growth is typically associated with aeolian sediment transport processes, while foredune erosion is associated with destructive marine processes. New data sets collected at a high energy, dissipative beach suggest that total water levels in the collision regime can cause dunes to accrete—requiring a paradigm shift away from considering collisional wave impacts as unconditionally erosional. From morphologic change data sets, it is estimated that marine processes explain between 9% and 38% of annual dune growth with aeolian processes accounting for the remaining 62% to 91%. The largest wind-driven dune growth occurs during the winter, in response to high wind velocities, but out of phase with summertime beach growth via intertidal sandbar welding. The lack of synchronization between maximum beach sediment supply and wind-driven dune growth indicates that aeolian transport at this site is primarily transport, rather than supply, limited, likely due to a lack of fetch limitations.

lakemorpho: Calculating lake morphometry metrics in R.

PubMed

Hollister, Jeffrey; Stachelek, Joseph

2017-01-01

Metrics describing the shape and size of lakes, known as lake morphometry metrics, are important for any limnological study. In cases where a lake has long been the subject of study these data are often already collected and are openly available. Many other lakes have these data collected, but access is challenging as it is often stored on individual computers (or worse, in filing cabinets) and is available only to the primary investigators. The vast majority of lakes fall into a third category in which the data are not available. This makes broad scale modelling of lake ecology a challenge as some of the key information about in-lake processes are unavailable. While this valuable in situ information may be difficult to obtain, several national datasets exist that may be used to model and estimate lake morphometry. In particular, digital elevation models and hydrography have been shown to be predictive of several lake morphometry metrics. The R package lakemorpho has been developed to utilize these data and estimate the following morphometry metrics: surface area, shoreline length, major axis length, minor axis length, major and minor axis length ratio, shoreline development, maximum depth, mean depth, volume, maximum lake length, mean lake width, maximum lake width, and fetch. In this software tool article we describe the motivation behind developing lakemorpho , discuss the implementation in R, and describe the use of lakemorpho with an example of a typical use case.

Are readers of our face readers of our minds? Dogs (Canis familiaris) show situation-dependent recognition of human's attention.

PubMed

Gácsi, Márta; Miklósi, Adám; Varga, Orsolya; Topál, József; Csányi, Vilmos

2004-07-01

The ability of animals to use behavioral/facial cues in detection of human attention has been widely investigated. In this test series we studied the ability of dogs to recognize human attention in different experimental situations (ball-fetching game, fetching objects on command, begging from humans). The attentional state of the humans was varied along two variables: (1) facing versus not facing the dog; (2) visible versus non-visible eyes. In the first set of experiments (fetching) the owners were told to take up different body positions (facing or not facing the dog) and to either cover or not cover their eyes with a blindfold. In the second set of experiments (begging) dogs had to choose between two eating humans based on either the visibility of the eyes or direction of the face. Our results show that the efficiency of dogs to discriminate between "attentive" and "inattentive" humans depended on the context of the test, but they could rely on the orientation of the body, the orientation of the head and the visibility of the eyes. With the exception of the fetching-game situation, they brought the object to the front of the human (even if he/she turned his/her back towards the dog), and preferentially begged from the facing (or seeing) human. There were also indications that dogs were sensitive to the visibility of the eyes because they showed increased hesitative behavior when approaching a blindfolded owner, and they also preferred to beg from the person with visible eyes. We conclude that dogs are able to rely on the same set of human facial cues for detection of attention, which form the behavioral basis of understanding attention in humans. Showing the ability of recognizing human attention across different situations dogs proved to be more flexible than chimpanzees investigated in similar circumstances.

Characteristics of wind waves in shallow tidal basins and how they affect bed shear stress, bottom erosion, and the morphodynamic evolution of coupled marsh and mudflat landforms

NASA Astrophysics Data System (ADS)

Tommasini, Laura; Carniello, Luca; Goodwin, Guillaume; Mudd, Simon M.; Matticchio, Bruno; D'Alpaos, Andrea

2017-04-01

Wind-wave induced erosion is one of the main processes controlling the morphodynamic evolution of shallow tidal basins, because wind waves promote the erosion of subtidal platforms, tidal flats and salt marshes. Our study considered zero-, one-and two-dimensional wave models. First, we analyzed the relations between wave parameters, depth and bed shear stress with constant and variable wave period considering two zero-dimensional models based on the Young and Verhagen (1996), and Carniello et al. (2005, 2011) approaches. The first one is an empirical method that computes wave height and the variable wave period from wind velocity, fetch and water depth. The second one is based on the solution of wave action conservation equation, we use this second approach for computing the bottom shear stress and wave height, considering variable and constant (t=2s) wave period. Second, we compared the wave spectral model SWAN with a fully coupled Wind-Wave Tidal Model applied to a 1D rectangular domain. These models describe both the growth and propagation of wind waves. Finally, we applied the two-dimensional Wind Wave Tidal Model (WWTM) to six different configurations of the Venice lagoon considering the same boundary conditions and we evaluated the spatial variation of mean wave power density. The analysis with zero-dimensional models show that the effects of the different model assumptions on the wave period and on the wave height computation cannot be neglected. In particular, the relationships between bottom shear stress and water depth have different shapes. Two results emerge: first, the differences are higher for small depths, and then the maximum values reached with the Young and Verhagen (1996) approach are greater than the maximum values obtained with WWTM approach. The results obtained with two-dimensional models suggest that the wave height is different in particular for small fetch, this could be due to the different formulation of the wave period. Finally, the application of WWTM for the entire Lagoon basin underlines an increase of the mean power density in the last four centuries, in particular in the central-southern part of the lagoon between Chioggia and Malamocco inlets.

2014 NASA Centennial Challenges Sample Return Robot Challenge

NASA Image and Video Library

2014-06-10

James Leopore, of team Fetch, from Alexandria, Virginia, speaks with judges as he prepares for the NASA 2014 Sample Return Robot Challenge, Tuesday, June 10, 2014, at the Worcester Polytechnic Institute (WPI) in Worcester, Mass. Team Fetch is one of eighteen teams competing for a $1.5 million NASA prize purse. Teams will be required to demonstrate autonomous robots that can locate and collect samples from a wide and varied terrain, operating without human control. The objective of this NASA-WPI Centennial Challenge is to encourage innovations in autonomous navigation and robotics technologies. Innovations stemming from the challenge may improve NASA's capability to explore a variety of destinations in space, as well as enhance the nation's robotic technology for use in industries and applications on Earth. Photo Credit: (NASA/Joel Kowsky)

Tools for Integrating Data Access from the IRIS DMC into Research Workflows

NASA Astrophysics Data System (ADS)

Reyes, C. G.; Suleiman, Y. Y.; Trabant, C.; Karstens, R.; Weertman, B. R.

2012-12-01

Web service interfaces at the IRIS Data Management Center (DMC) provide access to a vast archive of seismological and related geophysical data. These interfaces are designed to easily incorporate data access into data processing workflows. Examples of data that may be accessed include: time series data, related metadata, and earthquake information. The DMC has developed command line scripts, MATLAB® interfaces and a Java library to support a wide variety of data access needs. Users of these interfaces do not need to concern themselves with web service details, networking, or even (in most cases) data conversion. Fetch scripts allow access to the DMC archive and are a comfortable fit for command line users. These scripts are written in Perl and are well suited for automation and integration into existing workflows on most operating systems. For metdata and event information, the Fetch scripts even parse the returned data into simple text summaries. The IRIS Java Web Services Library (IRIS-WS Library) allows Java developers the ability to create programs that access the DMC archives seamlessly. By returning the data and information as native Java objects the Library insulates the developer from data formats, network programming and web service details. The MATLAB interfaces leverage this library to allow users access to the DMC archive directly from within MATLAB (r2009b or newer), returning data into variables for immediate use. Data users and research groups are developing other toolkits that use the DMC's web services. Notably, the ObsPy framework developed at LMU Munich is a Python Toolbox that allows seamless access to data and information via the DMC services. Another example is the MATLAB-based GISMO and Waveform Suite developments that can now access data via web services. In summary, there now exist a host of ways that researchers can bring IRIS DMC data directly into their workflows. MATLAB users can use irisFetch.m, command line users can use the various Fetch scripts, Java users can use the IRIS-WS library, and Python users may request data through ObsPy. To learn more about any of these clients see http://www.iris.edu/ws/wsclients/.

Mars Sample Return - Launch and Detection Strategies for Orbital Rendezvous

NASA Technical Reports Server (NTRS)

Woolley, Ryan C.; Mattingly, Richard L.; Riedel, Joseph E.; Sturm, Erick J.

2011-01-01

This study sets forth conceptual mission design strategies for the ascent and rendezvous phase of the proposed NASA/ESA joint Mars Sample Return Campaign. The current notional mission architecture calls for the launch of an acquisition/cache rover in 2018, an orbiter with an Earth return vehicle in 2022, and a fetch rover and ascent vehicle in 2024. Strategies are presented to launch the sample into a coplanar orbit with the Orbiter which facilitate robust optical detection, orbit determination, and rendezvous. Repeating ground track orbits exist at 457 and 572 km which provide multiple launch opportunities with similar geometries for detection and rendezvous.

Mars Sample Return: Launch and Detection Strategies for Orbital Rendezvous

NASA Technical Reports Server (NTRS)

Woolley, Ryan C.; Mattingly, Richard L.; Riedel, Joseph E.; Sturm, Erick J.

2011-01-01

This study sets forth conceptual mission design strategies for the ascent and rendezvous phase of the proposed NASA/ESA joint Mars Sample Return Campaign. The current notional mission architecture calls for the launch of an acquisition/ caching rover in 2018, an Earth return orbiter in 2022, and a fetch rover with ascent vehicle in 2024. Strategies are presented to launch the sample into a nearly coplanar orbit with the Orbiter which would facilitate robust optical detection, orbit determination, and rendezvous. Repeating ground track orbits existat 457 and 572 km which would provide multiple launch opportunities with similar geometries for detection and rendezvous.

A rapid parallelization of cone-beam projection and back-projection operator based on texture fetching interpolation

NASA Astrophysics Data System (ADS)

Xie, Lizhe; Hu, Yining; Chen, Yang; Shi, Luyao

2015-03-01

Projection and back-projection are the most computational consuming parts in Computed Tomography (CT) reconstruction. Parallelization strategies using GPU computing techniques have been introduced. We in this paper present a new parallelization scheme for both projection and back-projection. The proposed method is based on CUDA technology carried out by NVIDIA Corporation. Instead of build complex model, we aimed on optimizing the existing algorithm and make it suitable for CUDA implementation so as to gain fast computation speed. Besides making use of texture fetching operation which helps gain faster interpolation speed, we fixed sampling numbers in the computation of projection, to ensure the synchronization of blocks and threads, thus prevents the latency caused by inconsistent computation complexity. Experiment results have proven the computational efficiency and imaging quality of the proposed method.

Wave Tank Studies of Phase Velocities of Short Wind Waves

NASA Astrophysics Data System (ADS)

Ermakov, S.; Sergievskaya, I.; Shchegolkov, Yu.

Wave tank studies of phase velocities of short wind waves have been carried out using Ka-band radar and an Optical Spectrum Analyser. The phase velocities were retrieved from measured radar and optical Doppler shifts, taking into account measurements of surface drift velocities. The dispersion relationship was studied in centimetre (cm)- and millimetre(mm)-scale wavelength ranges at different fetches and wind speeds, both for a clean water surface and for water covered with surfactant films. It is ob- tained that the phase velocities do not follow the dispersion relation of linear capillary- gravity waves, increasing with fetch and, therefore, depending on phase velocities of dominant decimetre (dm)-centimetre-scale wind waves. One thus can conclude that nonlinear cm-mm-scale harmonics bound to the dominant wind waves and propagat- ing with the phase velocities of the decimetric waves are present in the wind wave spectrum. The resulting phase velocities of short wind waves are determined by re- lation between free and bound waves. The relative intensity of the bound waves in the spectrum of short wind waves is estimated. It is shown that this relation depends strongly on the surfactant concentration, because the damping effect due to films is different for free and bound waves; this results to changes of phase velocities of wind waves in the presence of surfactant films. This work was supported by MOD, UK via DERA Winfrith (Project ISTC 1774P) and by RFBR (Project 02-05-65102).

Development of a high-performance image server using ATM technology

NASA Astrophysics Data System (ADS)

Do Van, Minh; Humphrey, Louis M.; Ravin, Carl E.

1996-05-01

The ability to display digital radiographs to a radiologist in a reasonable time has long been the goal of many PACS. Intelligent routing, or pre-fetching images, has become a solution whereby a system uses a set of rules to route the images to a pre-determined destination. Images would then be stored locally on a workstation for faster display times. Some PACS use a large, centralized storage approach and workstations retrieve images over high bandwidth connections. Another approach to image management is to provide a high performance, clustered storage system. This has the advantage of eliminating the complexity of pre-fetching and allows for rapid image display from anywhere within the hospital. We discuss the development of such a storage device, which provides extremely fast access to images across a local area network. Among the requirements for development of the image server were high performance, DICOM 3.0 compliance, and the use of industry standard components. The completed image server provides performance more than sufficient for use in clinical practice. Setting up modalities to send images to the image server is simple due to the adherence to the DICOM 3.0 specification. Using only off-the-shelf components allows us to keep the cost of the server relatively inexpensive and allows for easy upgrades as technology becomes more advanced. These factors make the image server ideal for use as a clustered storage system in a radiology department.

Association between social support and place of delivery: a cross-sectional study in Kericho, Western Kenya

PubMed Central

2013-01-01

Background An estimated 358,000 maternal deaths still occur worldwide each year. The place of delivery is of great significance to the reduction of maternal mortality. Moreover, socio-economic factors, cultural traits, and local customs are associated with health-seeking behavior. This study aimed to explore determinants of association between social support and place of delivery. Methods This cross-sectional study was conducted from September to November 2011 at Sosiot Health Center, Kericho West District, Kenya. Participants were 303 mothers who brought their babies to the health center for immunization within their first year of life. Women underwent a structured interview using a questionnaire on demographic characteristics and their experiences of delivery including place of delivery and social support. Results The proportion of deliveries at health facilities was significantly higher in unmarried than married women (93% and 78%, respectively; P = 0.008). Unmarried women whose mothers supported them in housework and whose sisters helped them fetch water were more likely to deliver at health facilities (P = 0.002 and 0.042, respectively) than those without this support. However, married women whose husbands supported them in farming and whose neighbors helped them fetch water were less likely to deliver at health facilities (P = 0.003 and 0.021, respectively) than those without this support. Married women who were advised to deliver at a health facility by their mother-in-law or health staff were more likely to deliver at health facilities (P = 0.015 and 0.022, respectively) than those who did not receive this advice. Multivariate analysis revealed that married women were more likely to deliver at health facilities if they were highly educated (odds ratio [OR] = 2.5); had financial capability (OR = 4.3); had medical insurance (OR = 4.2); were primiparous (OR = 3.5); did not have the support of sisters-in-law for fetching water (OR = 2.2); or were advised to deliver at a health facility by family or neighbors (OR = 2.5). Conclusions Promotion of delivery at health facilities requires approaches that consider women’s social situation, since factors influencing place of delivery differ for married and unmarried women. PMID:24261639

Flexible Electrostatic Technology for Capture and Handling Project

NASA Technical Reports Server (NTRS)

Keys, Andrew; Bryan, Tom; Horwitz, Chris; Rakoczy, John; Waggoner, Jason

2015-01-01

To NASA unfunded & planned missions: This new capability to sense proximity, flexibly align to, and attractively grip and capture practically any object in space without any pre-designed physical features or added sensors or actuators will enable or enhance many of MSFC's strategic emphasis areas in space transportation, and space systems such as: 1. A Flexible Electrostatic gripper can enable the capture, gripping and releasing of an extraterrestrial sample of different minerals or a sample canister (metallic or composite) without requiring a handle or grapple fixture.(B) 2. Flexible self-aligning in-space capture/soft docking or berthing of ISS resupply vehicles, pressurized modules, or nodes for in-space assembly and shielding, radiator, and solar Array deployment for space habitats (C) 3. The flexible electrostatic gripper when combined with a simple steerable extendible boom can grip, position, and release objects of various shapes and materials with low mass and power without any prior handles or physical accommodations or surface contamination for ISS experiment experiments and in-situ repair.(F)(G) 4. The Dexterous Docking concept previously proposed to allow simple commercial resupply ships to station-keep and capture either ISS or an Exploration vehicle for supply or fluid transfer lacked a self-sensing, compliant, soft capture gripper like FETCH that could retract and attach to a CBM. (I) 5. To enable a soft capture and de-orbit of a piece of orbital debris will require self-aligning gripping and holding an object wherever possible (thermal coverings or shields of various materials, radiators, solar arrays, antenna dishes) with little or no residual power while adding either drag or active low level thrust.(K) 6. With the scalability of the FETCH technology, small satellites can be captured and handled or can incorporate FETCH gripper to dock to and handle other small vehicles and larger objects for de-orbiting or mitigating Orbital debris (L) 7. Many of previous MSFC and NASA proposals or concepts can now be realized or simplified by the development of the this initial and future FETCH grippers including commercial resupply, Exploration vehicle assembly, Satellite servicing, and orbital debris removal since a major part of these missions is to align to and capture some handle. Completed Project (2013 - 2014) Flexible Electrostatic Technology for Capture & Handling Project Center Innovation Fund: MSFC CIF Program | Space Technology Mission Directorate (STMD) For more information visit techport.nasa.gov Some NASA technology projects are smaller (for example SBIR/STTR, NIAC and Center Innovation Fund), and will have less content than other, larger projects. Newly created projects may not sensors or injection of permanent adhesives. With gripping forces estimated between 0.5 and 2.5 pounds per square inch or 70-300 lb./sq. ft. of surface contact, the FETCH can turn-on and turn-off rapidly and repeatedly to enable sample handling, soft docking, in-space assembly, and precision relocation for accurate anchor adhesion.

Bubble signatures revealed in antique artefacts

NASA Astrophysics Data System (ADS)

Wallace, Stephen C.; Kenney-Wallace, Geraldine

2016-01-01

Antique Chinese porcelain can fetch thousands of dollars on the art market. Stephen C Wallace and Geraldine Kenney-Wallace explain how their physics-based technique could help collectors and connoisseurs to tell a real antique object from a fake.

Atmospheric boundary layer modification in the marginal ice zone

NASA Technical Reports Server (NTRS)

Bennett, Theodore J., Jr.; Hunkins, Kenneth

1986-01-01

A case study of the Andreas et al. (1984) data on atmospheric boundary layer modification in the marginal ice zone is made. The model is a two-dimensional, multilevel, linear model with turbulence, lateral and vertical advection, and radiation. Good agreement between observed and modeled temperature cross sections is obtained. In contrast to the hypothesis of Andreas et al., the air flow is found to be stable to secondary circulations. Adiabatic lifting and, at long fetches, cloud top longwave cooling, not an air-to-surface heat flux, dominate the cooling of the boundary layer. The accumulation with fetch over the ice of changes in the surface wind field is shown to have a large effect on estimates of the surface wind stress. It is speculated that the Andreas et al. estimates of the drag coefficient over the compact sea ice are too high.

The Put-and-Fetch Ambiguity: How Magicians Exploit the Principle of Exclusive Allocation of Movements to Intentions.

PubMed

Van de Cruys, Sander; Wagemans, Johan; Ekroll, Vebjørn

2015-04-01

In many magic tricks, magicians fool their audience by performing a mock action (a so-called "ruse"), which merely serves the purpose of providing a seemingly natural explanation for visible movements that are actually part of the secret move they want to hide from the audience. Here, we discuss a special magic ruse in which the action of secretly putting something somewhere is "explained away" by the mock action of fetching something from the same place, or vice versa . Interestingly, the psychological principles underlying the amazing potency and robustness of this technique seem to be very similar to the general perceptual principles underlying figure-ground perception and the assignment of border ownership. This analogy may be useful for exploring the possibility that this and similar magical effects involve immediate "unconscious inferences" about intentions more akin to perceptual processing than to explicit deliberations based on a reflective "theory" of mind.

Influence of the sea-ice edge on the Arctic nearshore environment

NASA Astrophysics Data System (ADS)

Barnhart, K. R.; Overeem, I.; Anderson, R. S.

2013-12-01

Coasts form the dynamic interface of the terrestrial and oceanic systems. In the Arctic, and in much of the world, the coast is a zone of relatively high population, infrastructure, biodiversity, and ecosystem services. A significant difference between Arctic and temperate coasts is the presence of sea ice. Sea ice influences Arctic coasts in two main ways: (1) the length of the sea ice-free season controls the length of time over which nearshore water can interact with the land, and (2) the sea ice edge controls the fetch over which storm winds can blow over open water, resulting in changes in nearshore water level and wave field. The resulting nearshore hydrodynamic environment impacts all aspects of the coastal system. Here, we use satellite records of sea ice along with a simple model for wind-driven storm surge and waves to document how changes in the length and character of the sea ice-free season have impacted the nearshore hydrodynamic environment. For our sea ice analysis we primarily use the Bootstrap Sea Ice Concentrations from Nimbus-7 SMMR and DMSP SSM/I-SSMIS. We make whole-Arctic maps of sea ice change in the coastal zone. In addition to evaluating changes in length of the sea ice-free season at the coast, we look at changes segmented by azimuth. This allows us to consider changes in the sea ice in the context of the wind field. For our storm surge and wave field analysis we focus on the Beaufort Sea region. This region has experienced some of the greatest changes in both sea ice cover and coastal erosion rates in the Arctic and is anticipated to experience significant change in the future. In addition, the NOAA ESRL GMD has observed the wind field at Barrow since extends to 1977. In our past work on the rapid and accelerating coastal erosion, we have shown that one may model storm surge with a 2D numerical bathystrophic model, and that waves are well represented by the Shore Protection Manual methods for shallow-water fetch-limited waves. We use these models to explore the effect of increasing fetch on water level set up and wave generation. As increasing the fetch is one of the main effects of the changing sea ice cover, this allows us to connect changes in the sea ice cover to changes in the nearshore hydrodynamic environment. The long wind record allows for us to investigate changes in extreme wind and associated storm events. Preliminary analysis of Barrow and Drew Point indicate that at Drew Point the sea ice-free season has expanded by ˜17 days/decade while at Barrow it has expanded by ˜22 days/decade. We find the increase in the number of days when the sea ice edge is far away from the coast makes up a large proportion of the total increase in the duration of the sea ice-free season. For these days the sea ice edge does not provide a limit on the fetch over which water level set up and waves are generated.

78 FR 46997 - Agency Information Collection Activities: Submission for Review; Information Collection Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-02

... (DHS), Science and Technology, CyberForensics Electronic Technology Clearinghouse (CyberFETCH) Program... public to comment on data collection forms for the CyberForensics Electronic Technology Clearinghouse... for providing a collaborative environment for cyber forensics practitioners from law enforcement...

Predicting wind-driven waves in small reservoirs

USDA-ARS?s Scientific Manuscript database

The earthen levees commonly used for irrigation reservoirs are subjected to significant embankment erosion due to wind-generated waves. The design of bank protection measures relies on adequate prediction of wave characteristics based on wind conditions and fetch length. Current formulations are ba...

Ecosystem Design Principles for Restoring Deltaic Floodplains: Examples from Mississippi River Delta

NASA Astrophysics Data System (ADS)

Twilley, R.

2017-12-01

The Mississippi River Deltaic Plain (MRDP) provides examples for many of the functions and feedbacks regarding how human river management has impacted source-sink processes in coastal deltaic basins, resulting in human settlements more at risk to flooding from coastal storms. The Atchafalaya Basin, with continued sediment delivery, compared to Terrebonne Basin, with reduced river inputs, allow us to test assumptions of how landward migration of fringe wetlands of coastal basins as result of river management over the last 75 years can provide insights to these complex issues. The average landward migration for Terrebonne Basin was nearly 17,000 m (17 km) compared to only 22 m in Atchafalaya Basin over the last 78 yrs (p< 0.001), resulting in migration rates of 218 m/yr (0.22 km/yr) and < 0.5 m/yr, respectively. Shifts in fringe wetlands were very distinct in these two basins with gain of 25% in the Terrebonne Basin compared to 90% decrease in the Atchafalaya Basin since 1949. These shifts in vegetation types coincide with an increase in wind fetch in Terrebonne Bay, where we estimate that the wave power has increased by 50% 100% from 1932 to 2010 as the bathymetric and topographic conditions changed, and increase in maximum storm surge height also increased owing to the reduction of vegetated shorelines. We argue that this balance of land relative to water in this delta provides a much clearer understanding of increased flood risk from tropical cyclones rather than just estimates of areal land loss. The nonlinear response of migrating fringe wetlands as wind fetch increases is a critical feedback effect that should influence human river management decisions in deltaic coast. Restoration features focused on living shorelines may contribute to solutions to these non-linear feedbacks; but certain ecosystem design features have to be considered so such shorelines can adapt to relative sea level rise. Shorelines must have adaptive strategies compared to fixed hard structures - resulting on sediment management and redistribution as critical process to shoreline stabilization. Policies in US to encourage sediment placement associated with national dredge activities must be integrated to ecosystems services of fringe wetland restoration.

Aeolian sand transport over complex intertidal bar-trough beach topography

NASA Astrophysics Data System (ADS)

Anthony, Edward J.; Ruz, Marie-Hélène; Vanhée, Stéphane

2009-04-01

Aeolian sand transport on macrotidal beaches with complex intertidal bar-trough topography (ridge-and-runnel beaches) was assessed from experiments in northern France that involved measurements of wind speed, saltation, surface moisture contents, and rates of sand trapping across surveyed portions of the upper beach profile. Beaches exhibiting intertidal bars and troughs are much more complex, topographically, than simple reflective or dissipative beaches. Furthermore, the intertidal bar-trough morphology commonly exhibits strong cross-shore variations in the moisture contents of the beach surface and in patterns of bedform development. The results of four 30-minute experiments, conducted along topographically surveyed portions of the upper beach-dune toe profile, show that troughs act as extremely efficient sand interceptors, because of their permanently saturated state, which also inhibits sand mobilisation. Troughs, thus, limit or segment the dry fetch during conditions of intermittent saltation. Flow lines, inferred from the wind profiles, suggest that complex interactions at the boundary layer are generated by the bar-trough topography. Troughs systematically appear to be characterised by air expansion, while bar faces generate ramp wind acceleration for onshore winds, and sometimes immediate downwind deceleration for offshore winds. These effects may also contribute to cross-shore variations in the rates of sand trapping. Finally, a simple conceptual model of effective fetch development, integrating the effects of the spring-neap tidal range and of gross bar-trough morphological variability over time, is proposed for bar-trough beaches. The model highlights the key theme of fetch segmentation induced by cross-shore differentiation in the moisture contents of the beach surface hinged on the complex topography of multiple bars and troughs.

Improving the wave forecast in the Catalan Coast

NASA Astrophysics Data System (ADS)

Pallares, Elena; Sanchez-Arcilla, Agustin; Espino, Manuel

2014-05-01

This study has been motivated by the limited accuracy of wave models under short-duration, fetch-limited conditions. This applies particularly to the wave period, and can be illustrated by the case of semi-enclosed domains with highly variable wind patterns such as the Catalan coast in the Spanish Mediterranean. The wave model SWAN version 40.91A is used here in three nested grids covering all the North-western Mediterranean Sea with resolution from 9 to 1 km, forced with high resolution wind patterns from BSC (Barcelona Supercomputing Center) for two study periods, the winter 2010 and the spring 2011. The results are validated in eight locations with different types of instrumentation. In order to improve the results, a modification of the whitecapping well-known formulation of Hasselmann (1974) has been considered. The delta coefficient is increased to adapt the dissipation to the growth rates actually observed in the region. This correction introduces a dependence on the squared wave number, improving the prediction of the energy spectra at lower frequencies. However, one may note that an over-prediction will occur for waves with longer fetch and/or duration. The results obtained show a clear improvement of the mean and peak wave periods for the study area, decreasing considerably the negative bias observed previously, while almost no change is observed in wave height due to the proposed modifications. These results can be generalized to the Spanish Mediterranean coast and could be exported to similar environments, characterized by young/moderate sea wave conditions due to limited fetch and transient wind driving. References: - Hasselmann, K., 1974. On the spectral dissipation of ocean waves due to whitecapping. Boundary-layer Meteorology,6,107-127.

Comparative morphology of the mechanosensory lateral line system in a clade of New Zealand triplefin fishes.

PubMed

Wellenreuther, Maren; Brock, Michelle; Montgomery, John; Clements, Kendall D

2010-01-01

The mechanoreceptive lateral line system in fishes detects hydrodynamic stimuli and plays a critical role in many fundamental behaviours, including orientation to water currents and the detection of stationary objects, prey and predators. Interspecific variation in lateral line structure may result from a process of functional adaptation, with the background level of hydrodynamic activity proposed as an important selective pressure. Here we use the eight species of the ecologically diverse New Zealand marine triplefin fish of the genus Forsterygion and one species from the sister genus Notoclinops to investigate interspecific differences in lateral line morphology and to assess the relationship between lateral line characteristics and exposure to wave energy (fetch/depth ratio). Overall, the results show that lateral line traits are divergent between species, and these differences could in part be related to the wave exposure of the habitats that the species occupy. Specifically, numbers of canal neuromasts differed significantly between species, and most canal groupings increased in neuromast number with fetch/depth ratio, while the number and area of some superficial neuromast groupings decreased significantly with exposure. Distribution of superficial neuromasts along the trunk in the semi-pelagic and paedomorphic species F. maryannae differed from the other, demersal species, which may be associated with the unique lifestyle of this species and/or developmental processes. Canal architecture also differed considerably between species, but displayed no relationship with fetch/depth ratio. The results from this study indicate that some interspecific differences in lateral line organs may be a by-product of selection for habitat divergence. Future work should explore additional causal factors that might have influenced the evolution of lateral morphology in these species, including phylogenetic and allometric effects. Copyright 2010 S. Karger AG, Basel.

76 FR 22910 - Agency Information Collection Activities: Submission for Review; Information Collection Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

... (DHS), Science and Technology, CyberForensics Electronic Technology Clearinghouse (CyberFETCH) Program... public to comment on data collection forms for the CyberForensics Electronic Technology Clearinghouse... forensics practitioners from law enforcement, private sector and academia. This clearinghouse will enable...

76 FR 7870 - Agency Information Collection Activities: Submission for Review; Information Collection Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

... (DHS), Science and Technology, CyberForensics Electronic Technology Clearinghouse (CyberFETCH) Program... public to comment on data collection forms for the CyberForensics Electronic Technology Clearinghouse... forensics practitioners from law enforcement, private sector and academia. This clearinghouse will enable...

78 FR 66949 - Agency Information Collection Activities: Submission for Review; Information Collection Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-07

... (DHS), Science and Technology, CyberForensics Electronic Technology Clearinghouse (CyberFETCH) Program... public to comment on data collection forms for the CyberForensics Electronic Technology Clearinghouse... forensics practitioners from law enforcement, private sector and academia. This clearinghouse will enable...

Impact of sea-level rise on cross-shore sediment transport on fetch-limited barrier reef island beaches under modal and cyclonic conditions.

PubMed

Baldock, T E; Golshani, A; Atkinson, A; Shimamoto, T; Wu, S; Callaghan, D P; Mumby, P J

2015-08-15

A one-dimensional wave model is combined with an analytical sediment transport model to investigate the likely influence of sea-level rise on net cross-shore sediment transport on fetch-limited barrier reef and lagoon island beaches. The modelling considers if changes in the nearshore wave height and wave period in the lagoon induced by different water levels over the reef flat are likely to lead to net offshore or onshore movement of sediment. The results indicate that the effects of SLR on net sediment movement are highly variable and controlled by the bathymetry of the reef and lagoon. A significant range of reef-lagoon bathymetry, and notably shallow and narrow reefs, appears to lead hydrodynamic conditions and beaches that are likely to be stable or even accrete under SLR. Loss of reef structural complexity, particularly on the reef flat, increases the chance of sediment transport away from beaches and offshore. Copyright © 2015 Elsevier Ltd. All rights reserved.

Wave-ice interaction, observed and modelled

NASA Astrophysics Data System (ADS)

Gemmrich, Johannes

2017-04-01

The need for wide-spread, up-to-date sea state predictions and observations in the emerging ice-free Arctic will further increase as the region will open up to marine operations. Wave models for arctic regions have to capture the additional wave physics associated with wave-ice interactions, and different prediction schemes have to be tested against observations. Here we present examples of spatial wave field parameters obtained from TerraSAR-X StripMap swaths in the southern Beaufort Sea taken as part of the "Arctic Sea State and Boundary Layer DRI". Fetch evolution of the significant wave height and length in open waters, and dominant wave lengths and the high frequency cut-off of the wave spectrum in ice are readily extracted from the SAR (synthetic aperture radar) data. A surprising result is that wave evolution in off-ice wind conditions is more rapidly than the fetch evolution in off-land cases, suggesting seeding of the wave field within the ice-covered region.

Self-similar Theory of Wind-driven Sea

NASA Astrophysics Data System (ADS)

Zakharov, V. E.

2015-12-01

More than two dozens field experiments performed in the ocean and on the lakes show that the fetch-limited growth of dimensionless energy and dimensionless peak frequency is described by powerlike functions of the dimensionless fetch. Moreover, the exponents of these two functions are connected with a proper accuracy by the standard "magic relation", 10q-2p=1. Recent massive numerical experiments as far as experiments in wave tanks also confirm this magic relation. All these experimental facts can be interpreted in a framework of the following simple theory. The wind-driven sea is described by the "conservative" Hasselmann kinetic equation. The source terms, wind input and white-capping dissipation, play a secondary role in comparison with the nonlinear term Snl that is responsible for the four-wave resonant interaction. This equation has four-parameter family of self-similar solutions. The magic relation holds for all numbers of this family. This fact gives strong hope that development of self-consistent analytic theory of wind-driven sea is quite realizable task.

Tuple spaces in hardware for accelerated implicit routing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, Zachary Kent; Tripp, Justin

2010-12-01

Organizing and optimizing data objects on networks with support for data migration and failing nodes is a complicated problem to handle as systems grow. The goal of this work is to demonstrate that high levels of speedup can be achieved by moving responsibility for finding, fetching, and staging data into an FPGA-based network card. We present a system for implicit routing of data via FPGA-based network cards. In this system, data structures are requested by name, and the network of FPGAs finds the data within the network and relays the structure to the requester. This is acheived through successive examinationmore » of hardware hash tables implemented in the FPGA. By avoiding software stacks between nodes, the data is quickly fetched entirely through FPGA-FPGA interaction. The performance of this system is orders of magnitude faster than software implementations due to the improved speed of the hash tables and lowered latency between the network nodes.« less

MN GIS/LIS Consortium Annual Conference and Workshops, Rochester, MN, October 1-3, 2014

EPA Science Inventory

We mapped the distribution of multiple ecosystem services in the Saint Louis River Area of Concern (SLR AOC) under current and reported extreme lake levels. Services were mapped using measured or modeled natural features (i.e., bathymetry, vegetation, fetch, habitat, contaminated...

Flood and Weather Monitoring Using Real-time Twitter Data Streams

NASA Astrophysics Data System (ADS)

Demir, I.; Sit, M. A.; Sermet, M. Y.

2016-12-01

Social media data is a widely used source to making inference within public crisis periods and events in disaster times. Specifically, since Twitter provides large-scale data publicly in real-time, it is one of the most extensive resources with location information. This abstract provides an overview of a real-time Twitter analysis system to support flood preparedness and response using a comprehensive information-centric flood ontology and natural language processing. Within the scope of this project, we deal with acquisition and processing of real-time Twitter data streams. System fetches the tweets with specified keywords and classifies them as related to flooding or heavy weather conditions. The system uses machine learning algorithms to discover patterns using the correlation between tweets and Iowa Flood Information System's (IFIS) extensive resources. The system uses these patterns to forecast the formation and progress of a potential future flood event. While fetching tweets, predefined hashtags are used for filtering and enhancing the relevancy for selected tweets. With this project, tweets can also be used as an alternative data source where other data sources are not sufficient for specific tasks. During the disasters, the photos that people upload alongside their tweets can be collected and placed to appropriate locations on a mapping system. This allows decision making authorities and communities to see the most recent outlook of the disaster interactively. In case of an emergency, concentration of tweets can help the authorities to determine a strategy on how to reach people most efficiently while providing them the supplies they need. Thanks to the extendable nature of the flood ontology and framework, results from this project will be a guide for other natural disasters, and will be shared with the community.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Q; Read, P

Purpose: Multiple error pathways can lead to delivery errors during the treatment course that cannot be caught with pre-treatment QA. While in vivo solutions are being developed for linacs, no such solution exists for tomotherapy. The purpose of this study is to develop a near real-time system for tomotherapy that can monitor the delivery and dose accumulation process during the treatment-delivery, which enable the user to assess the impact of delivery variations and/or errors and to interrupt the treatment if necessary. Methods: A program running on a tomotherapy planning station fetches the raw DAS data during treatment. Exit detector datamore » is extracted as well as output, gantry angle, and other machine parameters. For each sample, the MLC open-close state is determined. The delivered plan is compared with the original plan via a Monte Carlo dose engine which transports fluence deviations from a pre-treatment Monte Carlo run. A report containing the difference in fluence, dose and DVH statistics is created in html format. This process is repeated until the treatment is completed. Results: Since we only need to compute the dose for the difference in fluence for a few projections each time, dose with 2% statistical uncertainty can be computed in less than 1 second on a 4-core cpu. However, the current bottleneck in this near real-time system is the repeated fetching and processing the growing DAS data file throughout the delivery. The frame rate drops from 10Hz at the beginning of treatment to 5Hz after 3 minutes and to 2Hz after 10 minutes. Conclusion: A during-treatment delivery monitor system has been built to monitor tomotherapy treatments. The system improves patient safety by allowing operators to assess the delivery variations and errors during treatment delivery and adopt appropriate actions.« less

Experimental Investigation of Cylindrical Floating Breakwater Performance with different mooring configurations

USDA-ARS?s Scientific Manuscript database

Floating breakwaters are typically used on limited-fetch water bodies, such as lakes, reservoirs, and bays, where wavelengths are relatively short. They are also often preferred for sites with large water level changes. Common uses are to protect small marinas or for shoreline erosion control. While...

New Learning - The IPP Programme: Improvements in Learning and Self Esteem by Changing the Organization of Learning

NASA Astrophysics Data System (ADS)

Garber, Klaus; Ausserer, Oskar; Giacomuzzi, Salvatore

"New learning" is basically an individualized learning style. "New learning" starts by the individual itself. The individual is the basis for conditions, learning contents, rhythm, duration and intensity of the teaching. The appropriate slogan is: fetch the individual at his personal conditions.

Global Citizenship Education for Every Student: The Washington, DC Public Schools' Study Abroad Program

ERIC Educational Resources Information Center

Engel, Laura C.; Fundalinski, Jessica; Gatalica, Kayla; Gibson, Heidi; Ireland, Kate

2017-01-01

What if every child could have a global experience? While such an idea might sound far-fetched, one school district is trying to change the narrative about access to study abroad through a large, fully-funded, district-wide global travel program.

Osmotic Power: A Fresh Look at an Old Experiment

ERIC Educational Resources Information Center

Dugdale, Pam

2014-01-01

Electricity from osmotic pressure might seem a far-fetched idea but this article describes a prototype in Norway where the osmotic pressure generated between salt and fresh water drives a turbine. This idea was applied in a student investigation, where they were tasked with researching which alternative materials could be used for the…

School Libraries: Their Planning and Equipment.

ERIC Educational Resources Information Center

School Library Association, London (England).

The elements discussed in this book reflect answers to questions dealing with the relationships of book accessibility to book segregation, fetch-and-take to sit-and-read, browsing to studying, book protection to student encouragement, discipline to comfort and relaxation, and talking to silence. Intended as a guide for all those who are concerned…

Modeling and measuring the nocturnal drainage flow in a high-elevation, subalpine forest with complex terrain

USGS Publications Warehouse

Yi, C.; Monson, Russell K.; Zhai, Z.; Anderson, D.E.; Lamb, B.; Allwine, G.; Turnipseed, A.A.; Burns, Sean P.

2005-01-01

The nocturnal drainage flow of air causes significant uncertainty in ecosystem CO2, H2O, and energy budgets determined with the eddy covariance measurement approach. In this study, we examined the magnitude, nature, and dynamics of the nocturnal drainage flow in a subalpine forest ecosystem with complex terrain. We used an experimental approach involving four towers, each with vertical profiling of wind speed to measure the magnitude of drainage flows and dynamics in their occurrence. We developed an analytical drainage flow model, constrained with measurements of canopy structure and SF6 diffusion, to help us interpret the tower profile results. Model predictions were in good agreement with observed profiles of wind speed, leaf area density, and wind drag coefficient. Using theory, we showed that this one-dimensional model is reduced to the widely used exponential wind profile model under conditions where vertical leaf area density and drag coefficient are uniformly distributed. We used the model for stability analysis, which predicted the presence of a very stable layer near the height of maximum leaf area density. This stable layer acts as a flow impediment, minimizing vertical dispersion between the subcanopy air space and the atmosphere above the canopy. The prediction is consistent with the results of SF6 diffusion observations that showed minimal vertical dispersion of nighttime, subcanopy drainage flows. The stable within-canopy air layer coincided with the height of maximum wake-to-shear production ratio. We concluded that nighttime drainage flows are restricted to a relatively shallow layer of air beneath the canopy, with little vertical mixing across a relatively long horizontal fetch. Insight into the horizontal and vertical structure of the drainage flow is crucial for understanding the magnitude and dynamics of the mean advective CO2 flux that becomes significant during stable nighttime conditions and are typically missed during measurement of the turbulent CO2 flux. The model and interpretation provided in this study should lead to research strategies for the measurement of these advective fluxes and their inclusion in the overall mass balance for CO2 at this site with complex terrain. Copyright 2005 by the American Geophysical Union.

Modeling and measuring the nocturnal drainage flow in a high-elevation, subalpine forest with complex terrain

NASA Astrophysics Data System (ADS)

Yi, Chuixiang; Monson, Russell K.; Zhai, Zhiqiang; Anderson, Dean E.; Lamb, Brian; Allwine, Gene; Turnipseed, Andrew A.; Burns, Sean P.

2005-11-01

The nocturnal drainage flow of air causes significant uncertainty in ecosystem CO2, H2O, and energy budgets determined with the eddy covariance measurement approach. In this study, we examined the magnitude, nature, and dynamics of the nocturnal drainage flow in a subalpine forest ecosystem with complex terrain. We used an experimental approach involving four towers, each with vertical profiling of wind speed to measure the magnitude of drainage flows and dynamics in their occurrence. We developed an analytical drainage flow model, constrained with measurements of canopy structure and SF6 diffusion, to help us interpret the tower profile results. Model predictions were in good agreement with observed profiles of wind speed, leaf area density, and wind drag coefficient. Using theory, we showed that this one-dimensional model is reduced to the widely used exponential wind profile model under conditions where vertical leaf area density and drag coefficient are uniformly distributed. We used the model for stability analysis, which predicted the presence of a very stable layer near the height of maximum leaf area density. This stable layer acts as a flow impediment, minimizing vertical dispersion between the subcanopy air space and the atmosphere above the canopy. The prediction is consistent with the results of SF6 diffusion observations that showed minimal vertical dispersion of nighttime, subcanopy drainage flows. The stable within-canopy air layer coincided with the height of maximum wake-to-shear production ratio. We concluded that nighttime drainage flows are restricted to a relatively shallow layer of air beneath the canopy, with little vertical mixing across a relatively long horizontal fetch. Insight into the horizontal and vertical structure of the drainage flow is crucial for understanding the magnitude and dynamics of the mean advective CO2 flux that becomes significant during stable nighttime conditions and are typically missed during measurement of the turbulent CO2 flux. The model and interpretation provided in this study should lead to research strategies for the measurement of these advective fluxes and their inclusion in the overall mass balance for CO2 at this site with complex terrain.

Application of a tree-level hydrodynamic model to simulate plot-level transpiration in the upland oak/pine forest in New Jersey

NASA Astrophysics Data System (ADS)

Mirfenderesgi, G.; Bohrer, G.; Matheny, A. M.; Fatichi, S.; Frasson, R. P. M.; Schafer, K. V.

2015-12-01

The Finite-Elements Tree-Crown Hydrodynamics model version 2 (FETCH2) simulates water flow through the tree using the porous media analogy. Empirical equations relate water potential within the stem to stomatal conductance at the leaf level. Leaves are connected to the stem at each height. While still simplified, this approach brings realism to the simulation of transpiration compared with models where stomatal conductance is directly linked to soil moisture. The FETCH2 model accounts for plant hydraulic traits such as xylem conductivity, area of hydro-active xylem, vertical distribution of leaf area, and maximal and minimal xylem water content, and their effect on the dynamics of water flow in the tree system. Such a modeling tool enhances our understanding of the role of hydraulic limitations and allows us to incorporate the effects of short-term water stresses on transpiration. Here, we use FETCH2 parameterized and evaluated with a large sap-flow observations data set, collected from 21 trees of two genera (oak/pine) at Silas Little Experimental Forest, NJ. The well-drained deep sandy soil leads to water stress during many days throughout the growing season. We conduct a set of tree-level transpiration simulations, and use the results to evaluate the effects of different hydraulic strategies on daily transpiration and water use efficiency. We define these "hydraulic strategies" through combinations of multiple sets of parameters in the model that describe the root, stem and leaf hydraulics. After evaluating the performance of the model, we use the results to shed light on the future trajectory of the forest in terms of species-specific transpiration responses. Application of the model on the two co-occurring oak species (Quercus prinus L. and Quercus velutina Lam) shows that the applied modeling approach was successfully captures the differences in water-use strategy through optimizing multiple physiological and hydraulic parameters.

Proposed Hydrodynamic Model Improves Resolution of Species-Specific Responses to Drought and Disturbance

NASA Astrophysics Data System (ADS)

Matheny, A. M.; Bohrer, G.; Fiorella, R.; Mirfenderesgi, G.

2015-12-01

Plant functional types in land surface models (LSMs) are broadly defined, and often represent species with different physiologies within the same category. For example, trees of opposing hydraulic strategies and traits are commonly grouped together, as is the case of red oak and red maple. As a result, LSMs generate typical patterns of errors in predictions of transpiration and production. We studied sap flux, stem water storage, stomatal conductance, photosynthesis, rooting depth, and bole growth of these species at disturbed and undisturbed field sites in Michigan. Species-specific differences significantly impact temporal patterns of stomatal conductance and overall transpiration responses to both drought and disturbance. During drought, maples relied heavily on stem-stored water, while oaks did not. After disturbance, oaks increased stomatal conductance while maple conductance declined. Isotopic analysis of xylem water revealed that oak roots can access a deep groundwater source, which maple roots cannot. This deep rooting strategy permits transpiration and growth to continue in oaks during periods of water limitation, even when maples cease transpiration. Using 16 years of bole growth data, we show that maple growth is strongly correlated with mean annual precipitation, yet oak growth is not. We propose a framework to incorporate these species-specific differences into LSMs using the Finite-Element Tree-Crown Hydrodynamics model version 2 (FETCH2) that resolves the fast dynamics and diurnal hysteresis of stomatal conductance at the tree level. FETCH2 uses atmospheric and biological forcings from the LSM, simulates water movement through trees as flow through a system of porous media conduits, and calculates realistic hydraulic restrictions to stomatal conductance. This model replaces the current, non-physical link which empirically connects soil moisture to stomatal conductance in LSMs. FETCH2 resolved transpiration is then easily scaled to the plot level using remote sensing data. By incorporating species-specific constraints on water flux into predictions of transpiration, growth, and mortality, we can improve simulations of the surface energy budget and global carbon and water balances.

Hurricanes, Coral Reefs and Rainforests: Resistance, Ruin and Recovery in the Caribbean

Treesearch

A. E. Lugo; C. S. Rogers; S. W Nixon

2000-01-01

The coexistence of hurricanes, coral reefs, and rainforests in the Caribbean demonstrates that highly structured ecosystems with great diversity can flourish in spite of recurring exposure to intense destructive energy. Coral reefs develop in response to wave energy and resist hurricanes largely by virtue of their structural strength. Limited fetch also protects some...

75 FR 38696 - Nectarines and Peaches Grown in California; Changes in Handling Requirements for Fresh Nectarines...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-06

... Web site: http://www.ams.usda.gov/AMSv1.0/ams.fetchTemplateData.do?template=TemplateN&page=Marketing... DEPARTMENT OF AGRICULTURE Agricultural Marketing Service 7 CFR Parts 916 and 917 [Doc. No. AMS-FV... Requirements for Fresh Nectarines and Peaches AGENCY: Agricultural Marketing Service, USDA. ACTION: Affirmation...

Changing the Way We Work

ERIC Educational Resources Information Center

Coote, Anna

2010-01-01

A 21-hour working week is a long way from today's standard of 40 hours or more, but not so far-fetched when people consider the infinitely varied ways in which they actually spend their time. On average, people of working age spend 19.6 hours a week in paid employment and 20.4 hours in unpaid housework and childcare. These averages mask huge…

Virtual Schools: The Changing Landscape of K-12 Education in the U.S.

ERIC Educational Resources Information Center

Toppin, Ian N.; Toppin, Sheila M.

2016-01-01

Virtual schools are a growing phenomenon in k-12 education. School systems in almost every state in the United States offer some version of fully online or blended education. It is no longer far-fetched to conclude that if the current trend continues, virtual school enrollments will eclipse those of traditional brick-and-mortar k-12 institutions…

Team Teaching: Old Chefs Come Up with New Recipe

ERIC Educational Resources Information Center

Grinols, Anne Bradstreet; Waller, Randall

2010-01-01

The call for papers on team teaching came to the authors at an almost perfect time because they are three quarters through their first rendition of their freshly minted team-taught course. Although they feel a little like chefs who are still tweaking the seasoning on their new gourmet creation when the servers come to fetch it, their information…

An Oceanographic and Climatological Atlas of Bristol Bay

DTIC Science & Technology

1987-10-01

36 Forecasting Method ................................ 38 SUPERSTRUCTURE ICING.............................. 41 WIND...slicks and risk general advection of oil by large-scale ice move- analysis to coastal regions were computed. ment, and specific advection of oil by the...tide 1) Fetch wind (speed and direction) from tables or other sources. Forecast time of a surface map analysis of pressure highest range based on loss of

Delphinus

NASA Astrophysics Data System (ADS)

Murdin, P.

2000-11-01

(the Dolphin; abbrev. Del, gen. Delphini; area 189 sq. deg.) A northern constellation which lies between Pegasus and Aquila, and culminates at midnight in late July. It represents either the messenger that the god Poseidon in Greek mythology sent to fetch the sea nymph Amphitrite to be his bride, or the dolphin that was said to have rescued Arion, a semilegendary poet and musician of Lesbos, who ...

Cruise Report: DOLCE VITA 1 and 2, 31 January-24 February and 26 May-15 June, 2003

DTIC Science & Technology

2005-02-01

reasonably well during the longer fetch of Jugo or Tramontana. It performed poorly during Bora). It must be mentioned that the Wind forecasts by...Report Craig Lee, Jason Gobat, Burton Jones, et al. N00014-02-1-0064 Steve Murray Processes and Prediction Division, Code 322 PO Offi ce of Naval

Experiments on waves under impulsive wind forcing in view of the Phillips (1957) theory

NASA Astrophysics Data System (ADS)

Shemer, Lev; Zavadsky, Andrey

2016-11-01

Only limited information is currently available on the initial stages of wind-waves growth from rest under sudden wind forcing; the mechanisms leading to the appearance of waves are still not well understood. In the present work, waves emerging in a small-scale laboratory facility under the action of step-like turbulent wind forcing are studied using capacitance and laser slope gauges. Measurements are performed at a number of fetches and for a range of wind velocities. Taking advantage of the fully automated experimental procedure, at least 100 independent realizations are recorded for each wind velocity at every fetch. The accumulated data sets allow calculating ensemble-averaged values of the measured parameters as a function of time elapsed from the blower activation. The accumulated results on the temporal variation of wind-wave field initially at rest allow quantitative comparison with the theory of Phillips (1957). Following Phillips, appearance of the initial detectable ripples was considered first, while the growth of short gravity waves at later times was analyzed separately. Good qualitative and partial quantitative agreement between the Phillips predictions and the measurements was obtained for both those stages of the initial wind-wave field evolution.

Pleistocene Lake Bonneville as an analog for extraterrestrial lakes and oceans: Chapter 21

USGS Publications Warehouse

Chan, M.A.; Jewell, P.; Parker, T.J.; Ormo, J.; Okubo, Chris; Komatsu, G.

2016-01-01

Geomorphic confirmation for a putative ancient Mars ocean relies on analog comparisons of coastal-like features such as shoreline feature attributes and temporal scales of process formation. Pleistocene Lake Bonneville is one of the few large, geologically young, terrestrial lake systems that exemplify well-preserved shoreline characteristics that formed quickly, on the order of a thousand years or less. Studies of Lake Bonneville provide two essential analog considerations for interpreting shorelines on Mars: (1) morphological variations in expression depend on constructional vs erosional processes, and (2) shorelines are not always correlative at an equipotential elevation across a basin due to isostasy, heat flow, wave setup, fetch, and other factors. Although other large terrestrial lake systems display supporting evidence for geomorphic comparisons, Lake Bonneville encompasses the most integrated examples of preserved coastal features related to basin history, sediment supply, climate, and fetch, all within the context of a detailed hydrograph. These collective terrestrial lessons provide a framework to evaluate possible boundary conditions for ancient Mars hydrology and large water body environmental feedbacks. This knowledge of shoreline characteristics, processes, and environments can support explorations of habitable environments and guide future mission explorations.

Quality of Piped and Stored Water in Households with Children Under Five Years of Age Enrolled in the Mali Site of the Global Enteric Multi-Center Study (GEMS)

PubMed Central

Baker, Kelly K.; Sow, Samba O.; Kotloff, Karen L.; Nataro, James P.; Farag, Tamer H.; Tamboura, Boubou; Doumbia, Mama; Sanogo, Doh; Diarra, Drissa; O'Reilly, Ciara E.; Mintz, Eric; Panchalingam, Sandra; Wu, Yukun; Blackwelder, William C.; Levine, Myron M.

2013-01-01

Water, sanitation, and hygiene information was collected during a matched case-control study of moderate and severe diarrhea (MSD) among 4,096 children < 5 years of age in Bamako, Mali. Primary use of piped water (conditional odds ratio [cOR] = 0.45; 0.34–0.62), continuous water access (cOR = 0.30; 0.20–0.43), fetching water daily (cOR = 0.77; 0.63–0.96), and breastfeeding (cOR = 0.65; 0.49–0.88) significantly reduced the likelihood of MSD. Fetching water in > 30 minutes (cOR = 2.56; 1.55–4.23) was associated with MSD. Piped tap water and courier-delivered water contained high (> 2 mg/L) concentrations of free residual chlorine and no detectable Escherichia coli. However, many households stored water overnight, resulting in inadequate free residual chlorine (< 0.2 mg/L) for preventing microbial contamination. Coliforms and E. coli were detected in 48% and 8% of stored household water samples, respectively. Although most of Bamako's population enjoys access to an improved water source, water quality is often compromised during household storage. PMID:23836570

Eddy-correlation measurements of fluxes of CO 2 and H 2O above a spruce stand

NASA Astrophysics Data System (ADS)

Ibrom, A.; Schütz, C.; Tworek, T.; Morgenstern, K.; Oltchev, A.; Falk, M.; Constantin, J.; Gravenhorst, G.

1996-12-01

Atmospheric fluxes of CO 2 and H 2O above a mature spruce stand ( Picea abies (L.) Karst.) have been investigated using the eddy- correlation technique. A closed path sensor adapted to the special requirements of long-term studies has been developed and tested. Field measurements have been performed since April 1995. Estimates of fetch showed a very narrow source area dimension under instable stratification (≤ 200 m). Fetch requirements at night are not met in some directions. Energy balance closure was influenced systematically by the wind direction indicating a substantial attenuation of the vertical wind motion by the tower (up to 40 %). Even for optimal flow directions, energy balance closure was about 88%. Intercomparison of the used ultra sonic anemometer (USAT-3) with a GILL - anemometer showed systematically lower values of vertical wind speed fluctuations (13 %). Average CO 2-fluxes ranged between -13 at noon to 3 μ mol m-2, s-1 at night in summer. In November and December the stand released CO 2 on a daily basis. A preliminary estimate of the cumulative net carbon balance over the observed period of 9 months is 4-5 t, Cha-1.

Design of a memory-access controller with 3.71-times-enhanced energy efficiency for Internet-of-Things-oriented nonvolatile microcontroller unit

NASA Astrophysics Data System (ADS)

Natsui, Masanori; Hanyu, Takahiro

2018-04-01

In realizing a nonvolatile microcontroller unit (MCU) for sensor nodes in Internet-of-Things (IoT) applications, it is important to solve the data-transfer bottleneck between the central processing unit (CPU) and the nonvolatile memory constituting the MCU. As one circuit-oriented approach to solving this problem, we propose a memory access minimization technique for magnetoresistive-random-access-memory (MRAM)-embedded nonvolatile MCUs. In addition to multiplexing and prefetching of memory access, the proposed technique realizes efficient instruction fetch by eliminating redundant memory access while considering the code length of the instruction to be fetched and the transition of the memory address to be accessed. As a result, the performance of the MCU can be improved while relaxing the performance requirement for the embedded MRAM, and compact and low-power implementation can be performed as compared with the conventional cache-based one. Through the evaluation using a system consisting of a general purpose 32-bit CPU and embedded MRAM, it is demonstrated that the proposed technique increases the peak efficiency of the system up to 3.71 times, while a 2.29-fold area reduction is achieved compared with the cache-based one.

Numerical and experimental results on the spectral wave transfer in finite depth

NASA Astrophysics Data System (ADS)

Benassai, Guido

2016-04-01

Determination of the form of the one-dimensional surface gravity wave spectrum in water of finite depth is important for many scientific and engineering applications. Spectral parameters of deep water and intermediate depth waves serve as input data for the design of all coastal structures and for the description of many coastal processes. Moreover, the wave spectra are given as an input for the response and seakeeping calculations of high speed vessels in extreme sea conditions and for reliable calculations of the amount of energy to be extracted by wave energy converters (WEC). Available data on finite depth spectral form is generally extrapolated from parametric forms applicable in deep water (e.g., JONSWAP) [Hasselmann et al., 1973; Mitsuyasu et al., 1980; Kahma, 1981; Donelan et al., 1992; Zakharov, 2005). The present paper gives a contribution in this field through the validation of the offshore energy spectra transfer from given spectral forms through the measurement of inshore wave heights and spectra. The wave spectra on deep water were recorded offshore Ponza by the Wave Measurement Network (Piscopia et al.,2002). The field regressions between the spectral parameters, fp and the nondimensional energy with the fetch length were evaluated for fetch-limited sea conditions. These regressions gave the values of the spectral parameters for the site of interest. The offshore wave spectra were transfered from the measurement station offshore Ponza to a site located offshore the Gulf of Salerno. The offshore local wave spectra so obtained were transfered on the coastline with the TMA model (Bouws et al., 1985). Finally the numerical results, in terms of significant wave heights, were compared with the wave data recorded by a meteo-oceanographic station owned by Naples Hydrographic Office on the coastline of Salerno in 9m depth. Some considerations about the wave energy to be potentially extracted by Wave Energy Converters were done and the results were discussed.

Programmable stream prefetch with resource optimization

DOEpatents

Boyle, Peter; Christ, Norman; Gara, Alan; Mawhinney, Robert; Ohmacht, Martin; Sugavanam, Krishnan

2013-01-08

A stream prefetch engine performs data retrieval in a parallel computing system. The engine receives a load request from at least one processor. The engine evaluates whether a first memory address requested in the load request is present and valid in a table. The engine checks whether there exists valid data corresponding to the first memory address in an array if the first memory address is present and valid in the table. The engine increments a prefetching depth of a first stream that the first memory address belongs to and fetching a cache line associated with the first memory address from the at least one cache memory device if there is not yet valid data corresponding to the first memory address in the array. The engine determines whether prefetching of additional data is needed for the first stream within its prefetching depth. The engine prefetches the additional data if the prefetching is needed.

Turbulence considerations for comparing ecosystem exchange over old-growth and clear-cut stands for limited fetch and complex canopy flow conditions

Treesearch

Sonia Wharton; Matt Schroeder; Kyaw Tha Paw U; Matthias Falk; Ken Bible

2009-01-01

Carbon dioxide (CO2), water vapor, and energy fluxes were measured using eddy covariance (EC) methodology over three adjacent evergreen forests in southern Washington State to identify stand-level age-effects on ecosystem exchange. The sites represent Douglas-fir forest ecosystems at two contrasting successional stages: old-growth (OG) and early...

In Search of Beauty

ERIC Educational Resources Information Center

Hyde, Hartley

2007-01-01

In 1854 the German scientist Zeising claimed that the ratio of a person's height to the height of their navel is in the same ratio as the Golden Ratio ([phi] = 1.62). There is so much hype about the Golden Ratio that it is worth reading an article at http://www.maa.org/devlin/devlin_06_04.html. It explains why some of the more far-fetched ideas…

An Architecture for Integrated Regional Health Telematics Networks

DTIC Science & Technology

2001-10-25

that enables informed citizens to have an impact on the healthcare system and to be more concerned and care for their own health . The current...resource, educational, integrated electronic health record (I- EHR ), and added value services [2]. These classes of telematic services are applica...cally distributed clinical information systems . 5) Finally, added-value services (e.g. image processing, information indexing, data pre-fetching

PH5: HDF5 Based Format for Integrating and Archiving Seismic Data

NASA Astrophysics Data System (ADS)

Hess, D.; Azevedo, S.; Falco, N.; Beaudoin, B. C.

2017-12-01

PH5 is a seismic data format created by IRIS PASSCAL using HDF5. Building PH5 on HDF5 allows for portability and extensibility on a scale that is unavailable in older seismic data formats. PH5 is designed to evolve to accept new data types as they become available in the future and to operate on a variety of platforms (i.e. Mac, Linux, Windows). Exemplifying PH5's flexibility is the evolution from just handling active source seismic data to now including passive source, onshore-offshore, OBS and mixed source seismic data sets. In PH5, metadata is separated from the time series data and stored in a size and performance efficient manner that also allows for easy user interaction and output of the metadata in a format appropriate for the data set. PH5's full-fledged "Kitchen Software Suite" comprises tools for data ingestion (e.g. RefTek, SEG-Y, SEG-D, SEG-2, MSEED), meta-data management, QC, waveform viewing, and data output. This software suite not only includes command line and GUI tools for interacting with PH5, it is also a comprehensive Python package to support the creation of software tools by the community to further enhance PH5. The PH5 software suite is currently being used in multiple capacities, including in-field for creating archive ready data sets as well as by the IRIS Data Management Center (DMC) to offer an FDSN compliant set of web services for serving PH5 data to the community in a variety of standard data and meta-data formats (i.e. StationXML, QuakeML, EventXML, SAC + Poles and Zeroes, MiniSEED, and SEG-Y) as well as StationTXT and ShotText formats. These web services can be accessed via standard FDSN clients such as ObsPy, irisFetch.m, FetchData, and FetchMetadata. This presentation will highlight and demonstrate the benefits of PH5 as a next generation adaptable and extensible data format for use in both archiving and working with seismic data.

Post-fire land treatments and wind erosion -- lessons from the Milford Flat Fire, UT, USA

USGS Publications Warehouse

Miller, Mark E.; Bowker, Matthew A.; Reynolds, Richard L.; Goldstein, Harland L.

2012-01-01

We monitored sediment flux at 25 plots located at the northern end of the 2007 Milford Flat Fire (Lake Bonneville Basin, west-central Utah) to examine the effectiveness of post-fire rehabilitation treatments in mitigating risks of wind erosion during the first 3 years post fire. Maximum values were recorded during Mar–Jul 2009 when horizontal sediment fluxes measured with BSNE samplers ranged from 16.3 to 1251.0 g m−2 d−1 in unburned plots (n = 8; data represent averages of three sampler heights per plot), 35.2–555.3 g m−2 d−1 in burned plots that were not treated (n = 5), and 21.0–44,010.7 g m−2 d−1 in burned plots that received one or more rehabilitation treatments that disturbed the soil surface (n = 12). Fluxes during this period exhibited extreme spatial variability and were contingent on upwind landscape characteristics and surficial soil properties, with maximum fluxes recorded in settings downwind of treated areas with long treatment length and unstable fine sand. Nonlinear patterns of wind erosion attributable to soil and fetch effects highlight the profound importance of landscape setting and soil properties as spatial factors to be considered in evaluating risks of alternative post-fire rehabilitation strategies. By Mar–Jul 2010, average flux for all plots declined by 73.6% relative to the comparable 2009 period primarily due to the establishment and growth of exotic annual plants rather than seeded perennial plants. Results suggest that treatments in sensitive erosion-prone settings generally exacerbated rather than mitigated wind erosion during the first 3 years post fire, although long-term effects remain uncertain.

The structure of the stably stratified internal boundary layer in offshore flow over the sea

NASA Astrophysics Data System (ADS)

Garratt, J. R.; Ryan, B. F.

1989-04-01

Observations obtained mainly from a research aircraft are presented of the mean and turbulent structure of the stably stratified internal boundary layer (IBL) over the sea formed by warm air advection from land to sea. The potential temperature and humidity fields reveal the vertical extent of the IBL, for fetches out to several hundred of kilometres, geostrophic winds of 20 25 m s-1, and potential temperature differences between undisturbed continental air and the sea surface of 7 to 17 K. The dependence of IBL depth on these external parameters is discussed in the context of the numerical results of Garratt (1987), and some discrepancies are noted. Wind observations show the development of a low-level wind maximum (wind component normal to the coast) and rotation of the wind to smaller cross-isobar flow angles. Potential temperature (θ) profiles within the IBL reveal quite a different structure to that found in the nocturnal boundary layer (NBL) over land. Over the sea, θ profiles have large positive curvature with vertical gradients increasing monotonically with height; this reflects the dominance of turbulent cooling within the layer. The behaviour is consistent with known behaviour in the NBL over land where curvature becomes negative (vertical gradients of θ decreasing with height) as radiative cooling becomes dominant. Turbulent properties are discussed in terms of non-dimensional quantities, normalised by the surface friction velocity, as functions of normalised height using the IBL depth. Vertical profiles of these and the normalised wavelength of the spectral maximum agree well with known results for the stable boundary layer over land (Caughey et al., 1979).

Parallel Programming Paradigms

DTIC Science & Technology

1987-07-01

Unclassified IS.. DECLASSIFICATIONIOOWNGRADIN G 16. DISTRIBUTION STATEMENT (of this Report) Distribution of this report is unlimited. 17...8416878 and by the Office of Naval Research Contracts No. N00014-86-K-0264 and No. N00014-85- K-0328. 8 ?~~ O . G 1 49 II Parallel Programming Paradigms...processors -. "to fetch from the same memory cell (list head) and thus seems to favor a shared memory - g implementation [37). In this dissertation, we

Robotic milking: Technology, farm design, and effects on work flow.

PubMed

Rodenburg, Jack

2017-09-01

Robotic milking reduces labor demands on dairy farms of all sizes and offers a more flexible lifestyle for farm families milking up to 250 cows. Because milking is voluntary, barn layouts that encourage low-stress access by providing adequate open space near the milking stations and escape routes for waiting cows improve milking frequency and reduce fetching. Because lame cows attend less often, preventing lameness with comfortable stalls, clean alley floors, and effective foot bathing warrants special emphasis in robotic dairies. Variable milking intervals create challenges for foot bathing, sorting and handling, and dealing with special-needs cows. Appropriate cow routing and separation options at the milking stations are needed to address these challenges and ensure that the expected labor savings are realized. Protocols and layout and gating should make it possible for a herd worker to complete all handling tasks alone. Free traffic and guided traffic systems yield similar results when excellent management is applied or when the number of cows is well below capacity. In less ideal circumstances, guided traffic and the use of commitment pens result in longer standing times and stress, particularly for lower ranking cows, and poor management with free traffic results in more labor for fetching. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Evaluating waterpoint sustainability and access implications of revenue collection approaches in rural Kenya

NASA Astrophysics Data System (ADS)

Foster, T.; Hope, R.

2017-02-01

Water policies in many sub-Saharan African countries stipulate that rural communities are responsible for self-financing their waterpoint's operation and maintenance. In the absence of policy consensus or evidence on optimal payment models, rural communities adopt a diversity of approaches to revenue collection. This study empirically assesses waterpoint sustainability and access outcomes associated with different revenue collection approaches on the south coast of Kenya. The analysis draws on a unique data set comprising financial records spanning 27 years and 100 communities, operational performance indicators for 200 waterpoints, and water source choices for more than 2000 households. Results suggest communities collecting pay-as-you-fetch fees on a volumetric basis generate higher levels of revenue and experience better operational performance than communities charging flat fees. In both cases, financial flows mirror seasonal rainfall peaks and troughs. These outcomes are tempered by evidence that households are more likely to opt for an unimproved drinking water source when a pay-as-you-fetch system is in place. The findings illuminate a possible tension between financial sustainability and universal access. If the Sustainable Development Goal of "safe water for all" is to become a reality, policymakers and practitioners will need to address this issue and ensure rural water services are both sustainable and inclusive.

Accelerating Smith-Waterman Algorithm for Biological Database Search on CUDA-Compatible GPUs

NASA Astrophysics Data System (ADS)

Munekawa, Yuma; Ino, Fumihiko; Hagihara, Kenichi

This paper presents a fast method capable of accelerating the Smith-Waterman algorithm for biological database search on a cluster of graphics processing units (GPUs). Our method is implemented using compute unified device architecture (CUDA), which is available on the nVIDIA GPU. As compared with previous methods, our method has four major contributions. (1) The method efficiently uses on-chip shared memory to reduce the data amount being transferred between off-chip video memory and processing elements in the GPU. (2) It also reduces the number of data fetches by applying a data reuse technique to query and database sequences. (3) A pipelined method is also implemented to overlap GPU execution with database access. (4) Finally, a master/worker paradigm is employed to accelerate hundreds of database searches on a cluster system. In experiments, the peak performance on a GeForce GTX 280 card reaches 8.32 giga cell updates per second (GCUPS). We also find that our method reduces the amount of data fetches to 1/140, achieving approximately three times higher performance than a previous CUDA-based method. Our 32-node cluster version is approximately 28 times faster than a single GPU version. Furthermore, the effective performance reaches 75.6 giga instructions per second (GIPS) using 32 GeForce 8800 GTX cards.

Influence of human activity patterns on epidemiology of plague in Western Usambara Mountains, Tanzania.

PubMed

Hubeau, Marianne; Gulinck, Hubert; Kimaro, Didas N; Hieronimo, Proches; Meliyo, Joel

2014-07-01

Human plague has been a recurring public health threat in some villages in the Western Usambara Mountains, Tanzania, in the period between 1980 and 2004. Despite intensive past biological and medical research, the reasons for the plague outbreaks in the same set of villages remain unknown. Plague research needs to broaden its scope and formulate new hypotheses. This study was carried out to establish relationships between the nature and the spatial extent of selected human activities on one hand, and the reported plague cases on the other hand. Three outdoor activities namely, fetching water, collecting firewood and going to the market, were selected. Through enquiries the activity patterns related to these activities were mapped in 14 villages. Standard deviation ellipses represent the extent of action spaces. Over 130 activity types were identified and listed. Of these, fetching water, collecting firewood and going to the market were used for further analysis. The results indicate a significant correlation between the plague frequency and the size of these action spaces. Different characteristics of land use and related human activities were correlated with the plague frequency at village and hamlet levels. Significant relationships were found between plague frequency and specific sources of firewood and water, and specific market places.

Physical modeling of the atmospheric boundary layer in the UNH Flow Physics Facility

NASA Astrophysics Data System (ADS)

Taylor-Power, Gregory; Gilooly, Stephanie; Wosnik, Martin; Klewicki, Joe; Turner, John

2016-11-01

The Flow Physics Facility (FPF) at UNH has test section dimensions W =6.0m, H =2.7m, L =72m. It can achieve high Reynolds number boundary layers, enabling turbulent boundary layer, wind energy and wind engineering research with exceptional spatial and temporal instrument resolution. We examined the FPF's ability to experimentally simulate different types of the atmospheric boundary layer (ABL) using upstream roughness arrays. The American Society for Civil Engineers defines standards for simulating ABLs for different terrain types, from open sea to dense city areas (ASCE 49-12). The standards require the boundary layer to match a power law shape, roughness height, and power spectral density criteria. Each boundary layer type has a corresponding power law exponent and roughness height. The exponent and roughness height both increase with increasing roughness. A suburban boundary layer was chosen for simulation and a roughness element fetch was created. Several fetch lengths were experimented with and the resulting boundary layers were measured and compared to standards in ASCE 49-12: Wind Tunnel Testing for Buildings and Other Structures. Pitot tube and hot wire anemometers were used to measure average and fluctuating flow characteristics. Velocity profiles, turbulence intensity and velocity spectra were found to compare favorably.

Influence of sea ice on Arctic coasts

NASA Astrophysics Data System (ADS)

Barnhart, K. R.; Kay, J. E.; Overeem, I.; Anderson, R. S.

2017-12-01

Coasts form the dynamic interface between the terrestrial and oceanic systems. In the Arctic, and in much of the world, the coast is a focal point for population, infrastructure, biodiversity, and ecosystem services. A key difference between Arctic and temperate coasts is the presence of sea ice. Changes in sea ice cover can influence the coast because (1) the length of the sea ice-free season controls the time over which nearshore water can interact with the land, and (2) the location of the sea ice edge controls the fetch over which storm winds can interact with open ocean water, which in turn governs nearshore water level and wave field. We first focus on the interaction of sea ice and ice-rich coasts. We combine satellite records of sea ice with a model for wind-driven storm surge and waves to estimate how changes in the sea ice-free season have impacted the nearshore hydrodynamic environment along Alaska's Beaufort Sea Coast for the period 1979-2012. This region has experienced some of the greatest changes in both sea ice cover and coastal erosion rates in the Arctic: the median length of the open-water season has expanded by 90 percent, while coastal erosion rates have more than doubled from 8.7 to 19 m yr-1. At Drew Point, NW winds increase shoreline water levels that control the incision of a submarine notch, the rate-limiting step of coastal retreat. The maximum water-level setup at Drew Point has increased consistently with increasing fetch. We extend our analysis to the entire Arctic using both satellite-based observations and global coupled climate model output from the Community Earth System Model Large Ensemble (CESM-LE) project. This 30-member ensemble employs a 1-degree version of the CESM-CAM5 historical forcing for the period 1920-2005, and RCP 8.5 forcing from 2005-2100. A control model run with constant pre-industrial (1850) forcing characterizes internal variability in a constant climate. Finally, we compare observations and model results to identify locations of both observed and expected rapid sea ice change. Based on satellite observations, the median length of the 2012 open-water season expanded by between 1.5 and 3-fold relative to 1979 over the Arctic Sea region. This results in open water during the stormy Arctic fall, with implications for not only coastal processes but for amplification of warming on land.

A stochastic perturbation method to generate inflow turbulence in large-eddy simulation models: Application to neutrally stratified atmospheric boundary layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Muñoz-Esparza, D.; Kosović, B.; Beeck, J. van

2015-03-15

Despite the variety of existing methods, efficient generation of turbulent inflow conditions for large-eddy simulation (LES) models remains a challenging and active research area. Herein, we extend our previous research on the cell perturbation method, which uses a novel stochastic approach based upon finite amplitude perturbations of the potential temperature field applied within a region near the inflow boundaries of the LES domain [Muñoz-Esparza et al., “Bridging the transition from mesoscale to microscale turbulence in numerical weather prediction models,” Boundary-Layer Meteorol., 153, 409–440 (2014)]. The objective was twofold: (i) to identify the governing parameters of the method and their optimummore » values and (ii) to generalize the results over a broad range of atmospheric large-scale forcing conditions, U{sub g} = 5 − 25 m s{sup −1}, where U{sub g} is the geostrophic wind. We identified the perturbation Eckert number, Ec=U{sub g}{sup 2}/ρc{sub p}θ{sup ~}{sub pm}, to be the parameter governing the flow transition to turbulence in neutrally stratified boundary layers. Here, θ{sup ~}{sub pm} is the maximum perturbation amplitude applied, c{sub p} is the specific heat capacity at constant pressure, and ρ is the density. The optimal Eckert number was found for nonlinear perturbations allowed by Ec ≈ 0.16, which instigate formation of hairpin-like vortices that most rapidly transition to a developed turbulent state. Larger Ec numbers (linear small-amplitude perturbations) result in streaky structures requiring larger fetches to reach the quasi-equilibrium solution, while smaller Ec numbers lead to buoyancy dominated perturbations exhibiting difficulties for hairpin-like vortices to emerge. Cell perturbations with wavelengths within the inertial range of three-dimensional turbulence achieved identical quasi-equilibrium values of resolved turbulent kinetic energy, q, and Reynolds-shear stress, . In contrast, large-scale perturbations acting at the production range exhibited reduced levels of , due to the formation of coherent streamwise structures, while q was maintained, requiring larger fetches for the turbulent solution to stabilize. Additionally, the cell perturbation method was compared to a synthetic turbulence generator. The proposed stochastic approach provided at least the same efficiency in developing realistic turbulence, while accelerating the formation of large-scales associated with production of turbulent kinetic energy. Also, it is computationally inexpensive and does not require any turbulent information.« less

Record bid for Einstein letter

NASA Astrophysics Data System (ADS)

Jeandron, Michelle

2008-06-01

A letter written by Albert Einstein the year before his death has sold for the staggering amount of £170 000 at an auction in London last month. The previously unrecorded letter, which has spent the past 50 years in a private collection, includes a discussion of Einstein's views on religion, bringing new material to the debate about whether or not he believed in God. The lot had been expected to fetch between £6000-£8000.

The Morphometry of Lake Palmas, a Deep Natural Lake in Brazil

PubMed Central

Barroso, Gilberto F.; Gonçalves, Monica A.; Garcia, Fábio da C.

2014-01-01

Lake Palmas (A = 10.3km2) is located in the Lower Doce River Valley (LDRV), on the southeastern coast of Brazil. The Lake District of the LDRV includes 90 lakes, whose basic geomorphology is associated with the alluvial valleys of the Barreiras Formation (Cenozoic, Neogene) and with the Holocene coastal plain. This study aimed to investigate the relationship of morphometry and thermal pattern of a LDRV deep lake, Lake Palmas. A bathymetric survey carried out in 2011 and the analysis of hydrographic and wind data with a geographic information system allowed the calculation of several metrics of lake morphometry. The vertical profiling of physical and chemical variables in the water column during the wet/warm and dry/mild cold seasons of 2011 to 2013 has furnished a better understanding of the influence of the lake morphometry on its structure and function. The overdeepened basin has a subrectangular elongated shape and is aligned in a NW-SE direction in an alluvial valley with a maximum depth (Zmax) of 50.7m, a volume of 2.2×108 m3 (0.22km3) and a mean depth (Zmv) of 21.4m. These metrics suggest Lake Palmas as the deepest natural lake in Brazil. Water column profiling has indicated strong physical and chemical stratification during the wet/warm season, with a hypoxic/anoxic layer occupying one-half of the lake volume. The warm monomictic pattern of Lake Palmas, which is in an accordance to deep tropical lakes, is determined by water column mixing during the dry and mild cold season, especially under the influence of a high effective fetch associated with the incidence of cold fronts. Lake Palmas has a very long theoretical retention time, with a mean of 19.4 years. The changes observed in the hydrological flows of the tributary rivers may disturb the ecological resilience of Lake Palmas. PMID:25406062

Diurnal and Seasonal Variations of Thermal Stratification and Vertical Mixing in a Shallow Fresh Water Lake

NASA Astrophysics Data System (ADS)

Yang, Yichen; Wang, Yongwei; Zhang, Zhen; Wang, Wei; Ren, Xia; Gao, Yaqi; Liu, Shoudong; Lee, Xuhui

2018-04-01

Among several influential factors, the geographical position and depth of a lake determine its thermal structure. In temperate zones, shallow lakes show significant differences in thermal stratification compared to deep lakes. Here, the variation in thermal stratification in Lake Taihu, a shallow fresh water lake, is studied systematically. Lake Taihu is a warm polymictic lake whose thermal stratification varies in short cycles of one day to a few days. The thermal stratification in Lake Taihu has shallow depths in the upper region and a large amplitude in the temperature gradient, the maximum of which exceeds 5°C m-1. The water temperature in the entire layer changes in a relatively consistent manner. Therefore, compared to a deep lake at similar latitude, the thermal stratification in Lake Taihu exhibits small seasonal differences, but the wide variation in the short term becomes important. Shallow polymictic lakes share the characteristic of diurnal mixing. Prominent differences on the duration and frequency of long-lasting thermal stratification are found in these lakes, which may result from the differences of local climate, lake depth, and fetch. A prominent response of thermal stratification to weather conditions is found, being controlled by the stratifying effect of solar radiation and the mixing effect of wind disturbance. Other than the diurnal stratification and convection, the representative responses of thermal stratification to these two factors with contrary effects are also discussed. When solar radiation increases, stronger wind is required to prevent the lake from becoming stratified. A daily average wind speed greater than 6 m s-1 can maintain the mixed state in Lake Taihu. Moreover, wind-induced convection is detected during thermal stratification. Due to lack of solar radiation, convection occurs more easily in nighttime than in daytime. Convection occurs frequently in fall and winter, whereas long-lasting and stable stratification causes less convection in summer.

Interpretation of surface flux measurements in heterogeneous terrain during the Monsoon '90 experiment

USGS Publications Warehouse

Stannard, D.I.; Blanford, J.H.; Kustas, William P.; Nichols, W.D.; Amer, S.A.; Schmugge, T.J.; Weltz, M.A.

1994-01-01

A network of 9-m-tall surface flux measurement stations were deployed at eight sparsely vegetated sites during the Monsoon '90 experiment to measure net radiation, Q, soil heat flux, G, sensible heat flux, H (using eddy correlation), and latent heat flux, λE (using the energy balance equation). At four of these sites, 2-m-tall eddy correlation systems were used to measure all four fluxes directly. Also a 2-m-tall Bowen ratio system was deployed at one site. Magnitudes of the energy balance closure (Q + G + H + λE) increased as the complexity of terrain increased. The daytime Bowen ratio decreased from about 10 before the monsoon season to about 0.3 during the monsoons. Source areas of the measurements are developed and compared to scales of heterogeneity arising from the sparse vegetation and the topography. There was very good agreement among simultaneous measurements of Q with the same model sensor at different heights (representing different source areas), but poor agreement among different brands of sensors. Comparisons of simultaneous measurements of G suggest that because of the extremely small source area, extreme care in sensor deployment is necessary for accurate measurement in sparse canopies. A recently published model to estimate fetch is used to interpret measurements of H at the 2 m and 9 m heights. Three sites were characterized by undulating topography, with ridgetops separated by about 200–600 m. At these sites, sensors were located on ridgetops, and the 9-m fetch included the adjacent valley, whereas the 2-m fetch was limited to the immediate ridgetop and hillside. Before the monsoons began, vegetation was mostly dormant, the watershed was uniformly hot and dry, and the two measurements of H were in close agreement. After the monsoons began and vegetation fully matured, the 2-m measurements of H were significantly greater than the 9-m measurements, presumably because the vegetation in the valleys was denser and cooler than on the ridgetops and hillsides. At one lowland site with little topographic relief, the vegetation was more uniform, and the two measurements of H were in close agreement during peak vegetation. Values of λE could only be compared at two sites, but the 9-m values were greater than the 2-m values, suggesting λE from the dense vegetation in the valleys was greater than elsewhere.

A CRAY-Class Multiprocessor Simulator.

DTIC Science & Technology

1983-09-01

instruction will appear in this column. 38 ! ?m L < ¢ < . - ?. .., ..i.-..--. .°.- ’’ , ... .,. ... 18. BCG -The parcel buffer change flag. When the next...program is first started up, no instruction parcels are in the parcel buffers so a fetch is required. The asterisk in the BCG field indicates a buffer...an in-buffer target address. While the buffer change is in progress, the instruction causing the change will place its tag in the BCG column. Once the

Engendering Responses to Complex Emergencies: Lessons from South Sudan

DTIC Science & Technology

2016-03-01

cattle raiding, gender roles also come into play in broader conflict tactics and strategies. Rape and sexual violence have become very com- mon in...Sudan. Women and girls suffer most from rape , but there is an increasing stock of evi- dence that boys and young men are vulnerable to rape as well...firewood and wild fruits, fetch water, as well as weed and harvest. These daily chores expose women to risks of violence and rape , which are often

Secure and Practical Defense Against Code-Injection Attacks using Software Dynamic Translation

DTIC Science & Technology

2006-06-16

Cache inst1 inst2 … instx inst3 inst4 cmpl %eax,%ecx trampoline Code Fragment1 inst7 inst8 … trampoline Code Fragment2 Context Switch Fetch Decode...inst4 cmpl %eax,%ecx bne L4 inst5 inst6 … jmp L8 L4: inst7 inst8 … Application Text CFn CFn+1 CFn+2 CFn+3 CFn+4 CFn+5 CFn+x inst5 inst6 … trampoline

Wetlands Research Program. Wetland Evaluation Technique (WET). Volume 2. Methodology.

DTIC Science & Technology

1987-10-01

in Zones B or C fiom wind. (b) Open water fetch is less than 100 ft (Figure 19)? 19.1B (Answer "I" if the AA/IA is mostly a riverine wetland system ...and upland .... 58 19 Examples of sheltered open water in the AA/IA .................. 59 20 Example of a wetland protected shoreline...the wetland and adjacent of the channel, as well as contiguous wetlands within open water for a distance of 300 ft. from the deep 0.5 mile. water

Visible and Thermal Imaging of Sea Ice and Open Water from Coast Guard Arctic Domain Awareness Flights

DTIC Science & Technology

2014-09-30

dropsondes, micro- aircraft), cloud top/base heights Arctic Ocean Surface Temperature project Steele Buoy drops for SLP , SST, SSS, & surface velocity...Colón & Vancas (NIC) Drop buoys for SLP , temperature and surface velocity Waves & Fetch in the MIZ Thompson SWIFTS buoys measuring wave energy...Expendable CTD, AXCP= Air Expendable Current Profiler, SLP = Sea Level atmospheric Pressure, SST= Seas Surface Temperature, A/C= aircraft, FSD= Floe Size Distribution, SIC=Sea Ice Concentration

Nonlinearity Role in Long-Term Interaction of the Ocean Gravity Waves

DTIC Science & Technology

2012-09-30

3 4 =s We found that in the fetch-limited case the wind forcing index s is similar to the time domain situation, and the wind forcing is given by...of its evolution. Fig.5 gives a graphical summary of four reference cases of self-similar evolution of wind-driven waves. These cases are shown as...different R, tangents of one-parametric dependencies H~TR height-to-period in logarithmic axes. Reference cases of growing wind sea are shown as

The 3D laser radar vision processor system

NASA Astrophysics Data System (ADS)

Sebok, T. M.

1990-10-01

Loral Defense Systems (LDS) developed a 3D Laser Radar Vision Processor system capable of detecting, classifying, and identifying small mobile targets as well as larger fixed targets using three dimensional laser radar imagery for use with a robotic type system. This processor system is designed to interface with the NASA Johnson Space Center in-house Extra Vehicular Activity (EVA) Retriever robot program and provide to it needed information so it can fetch and grasp targets in a space-type scenario.

The 3D laser radar vision processor system

NASA Technical Reports Server (NTRS)

Sebok, T. M.

1990-01-01

Loral Defense Systems (LDS) developed a 3D Laser Radar Vision Processor system capable of detecting, classifying, and identifying small mobile targets as well as larger fixed targets using three dimensional laser radar imagery for use with a robotic type system. This processor system is designed to interface with the NASA Johnson Space Center in-house Extra Vehicular Activity (EVA) Retriever robot program and provide to it needed information so it can fetch and grasp targets in a space-type scenario.

Documentation of logistics transfer from shuttle Spacehab

NASA Image and Video Library

1996-04-24

STS076-345-019 (22 - 31 March 1996) --- Onboard the Spacehab Module in the cargo bay of the Earth-orbiting Space Shuttle Atlantis, astronaut Richard A. Searfoss fetches a battery which is to be transferred to Russia's Mir Space Station. The pilot and his crew mates docked with Mir on March 23, 1996, and remained linked until March 28, 1996. At right is a stowed gyrodyne, which earlier had been replaced on Mir with a new one brought up from the ground by the STS-76 crew.

Classical and Non-Classical Regimes of the Limited-Fetch Wave Growth and Localized Structures on the Surface of Water

DTIC Science & Technology

2013-09-30

specifying the wave-maker driving signal . The short intense envelope solitons possess vertical asymmetry similar to regular Stokes waves with the same...presented in [P1], [P2]. 2. Physical model of sea wave period from altimeter data We use the asymptotic theory of wind wave growth proposed in [R6...relationship can be used for processing altimeter data assuming the wave field to be stationary and spatially inhomogeneous. It is consistent with

Further Discussion: Parametric Study of Wind Generated Supermicron Particle Effects in Large Fires

NASA Technical Reports Server (NTRS)

Toon, O. B.; Ackerman, T. P.

1987-01-01

In their reply (Porch et al., 1987) to our comments (Turco et al., 1987) on their smoke-scavenging-by-dust paper, Porch et al. attempt to justify a number of parameter assumptions in their original article, again revealing the extreme nature of those assumptions, particularly in the situation where all are taken simultaneously. In critiquing Porch et al.'s calculations, have not applied "opinion", but rather physical reality and common sense expressed through basic experimental results and logical physical bounds. A few examples of the unrealistic conditions required by the Porch et al. scavenging scheme, as described in their paper and comments, should suffice here. ) Porch et al. have fabricated a "fetch" region for dust particles in large fire plumes that logically must extend over an area up to 50 times greater than the fire area itself. Alternatively, they have invoked significant "necking down' of the fire plume, so that its cross-sectional area is at most a few percent of the fire area. Such severe constriction is seen only in very small fires with strong, organized vorticity, and then only over a limited plume rise region. No "fetch" has ever been noted in any large-scale fires we have observed, or for which accounts are available. Indeed, as we deduced in our original comments, complete dust scavenging even within the fire zone would probably occur less than 10% of the time for large urban fires.

Large-Scale Overlays and Trends: Visually Mining, Panning and Zooming the Observable Universe.

PubMed

Luciani, Timothy Basil; Cherinka, Brian; Oliphant, Daniel; Myers, Sean; Wood-Vasey, W Michael; Labrinidis, Alexandros; Marai, G Elisabeta

2014-07-01

We introduce a web-based computing infrastructure to assist the visual integration, mining and interactive navigation of large-scale astronomy observations. Following an analysis of the application domain, we design a client-server architecture to fetch distributed image data and to partition local data into a spatial index structure that allows prefix-matching of spatial objects. In conjunction with hardware-accelerated pixel-based overlays and an online cross-registration pipeline, this approach allows the fetching, displaying, panning and zooming of gigabit panoramas of the sky in real time. To further facilitate the integration and mining of spatial and non-spatial data, we introduce interactive trend images-compact visual representations for identifying outlier objects and for studying trends within large collections of spatial objects of a given class. In a demonstration, images from three sky surveys (SDSS, FIRST and simulated LSST results) are cross-registered and integrated as overlays, allowing cross-spectrum analysis of astronomy observations. Trend images are interactively generated from catalog data and used to visually mine astronomy observations of similar type. The front-end of the infrastructure uses the web technologies WebGL and HTML5 to enable cross-platform, web-based functionality. Our approach attains interactive rendering framerates; its power and flexibility enables it to serve the needs of the astronomy community. Evaluation on three case studies, as well as feedback from domain experts emphasize the benefits of this visual approach to the observational astronomy field; and its potential benefits to large scale geospatial visualization in general.

Supraglacial lakes on Himalayan debris-covered glacier (Invited)

NASA Astrophysics Data System (ADS)

Sakai, A.; Fujita, K.

2013-12-01

Debris-covered glaciers are common in many of the world's mountain ranges, including in the Himalayas. Himalayan debris-covered glacier also contain abundant glacial lakes, including both proglacial and supraglacial types. We have revealed that heat absorption through supraglacial lakes was about 7 times greater than that averaged over the whole debris-covered zone. The heat budget analysis elucidated that at least half of the heat absorbed through the water surface was released with water outflow from the lakes, indicating that the warm water enlarge englacial conduits and produce internal ablation. We observed some portions at debris-covered area has caved at the end of melting season, and ice cliff has exposed at the side of depression. Those depression has suggested that roof of expanded water channels has collapsed, leading to the formation of ice cliffs and new lakes, which would accelerate the ablation of debris-covered glaciers. Almost glacial lakes on the debris-covered glacier are partially surrounded by ice cliffs. We observed that relatively small lakes had non-calving, whereas, calving has occurred at supraglacial lakes with fetch larger than 80 m, and those lakes expand rapidly. In the Himalayas, thick sediments at the lake bottom insulates glacier ice and lake water, then the lake water tends to have higher temperature (2-4 degrees C). Therefore, thermal undercutting at ice cliff is important for calving processes in the glacial lake expansion. We estimated and subaqueous ice melt rates during the melt and freeze seasons under simple geomorphologic conditions. In particular, we focused on valley wind-driven water currents in various fetches during the melt season. Our results demonstrate that the subaqueous ice melt rate exceeds the ice-cliff melt rate above the water surface when the fetch is larger than 20 m with the water temperature of 2-4 degrees C. Calculations suggest that onset of calving due to thermal undercutting is controlled by water currents driven by winds at the lake surface with a positive feedback process. The risk of GLOFs (glacial lake outburst flood) are analysed for Himalayan glacial lakes. We proposed an objective index for GLOF probability, based on depression angle from the lakeshore, which allows the lakes to be assessed using remotely sensed digital elevation models (DEMs). The index was verified by pre-GLOF topography derived by spy satellite imageries. We screened 2800 Himalayan glacial lakes and identified 49 lakes with potential flood volumes over 10 million m3.

Can small zooplankton enhance turbulence in a lake during vertical migration?

NASA Astrophysics Data System (ADS)

Wain, D.; Simoncelli, S.; Thackeray, S.

2016-02-01

Recent research in both oceanic and freshwater systems suggests that the Diel Vertical Migration (DVM), a predator-avoidance mechanism adopted by many zooplankton, may be an underrepresented source of turbulence and mixing. In particular, the migration can play a crucial role when organisms cross the thermocline; this could be particularly important in enhancing the mixing in lakes, where the pelagic zone is often quiescent, with a consequent impact on lake ecosystem functioning. A field experiment was performed to directly measure the temperature fluctuations and kinetic energy dissipation rate generated by DVM of Daphnia spp., a 1 mm crustacean zooplankton genus. Profiles of turbulence were acquired with a temperature microstructure profiler in Vobster Quay (UK), a small quarry with small wind fetch, steep sides, and with a maximum depth of approximately 25 m. Sixteen profiles were measured over the course of two hours during sunset on 16 July 2015, during which there was no wind. Backscatter strength from bottom-mounted ADCP was used as a proxy to assess DVM. Zooplankton vertical distribution was also quantified by sampling with a 100 μm mesh net before and after the turbulence profiling in 8 layers to verify the distribution of Daphnia spp. before and after the migration. Zooplankton tows show higher abundance (450 ind./L) of Daphnia at 9m and near the bottom before sunset (8PM). Samples after dusk (11.20PM) showed an increase in the surface layer, from 0 up to 250 ind./L. However, migration also appears to happen horizontally. Ensemble-averaged profiles show a great variation of the dissipation rates over the course of the time series with a peak of 10-7 W/kg between 6m and 12m where the DVM is happening and with respect to profiles before sunset. Given the uncertainty in measuring the length scales of turbulence associated with small zooplankton, further analysis is required to determine if the observed turbulence during the time of migration was due the migration or due to other causes, such as the onset of penetrative convection associated with night-time cooling. Three further datasets were collected during sunset in August and September 2015 and will be used to determine if turbulence is always present during the migrations.

Local-Rapid Evaluation of Atmospheric Conditions (L-REAC) System, Design and Development Volume 5 (Mobile L-REAC System Proof of Concept and Four Feasibility Studies)

DTIC Science & Technology

2012-12-01

List of Symbols, Abbreviations, and Acronyms 52 Distribution List 56 v List of Figures Figure 1. 1994 EPA/NOAA wind tunnel results show the...Atmospheric Administration (NOAA) wind tunnel study. Six of the seven features are shown in figure 1: fetch flow, velocity acceleration, velocity deficit...Figure 1. 1994 EPA/NOAA wind tunnel results show the airflow pattern around a single structure. Streamline flow is from left to right. The “canyon

Personal Computer Program for Chemical Hazard Prediction (D2PC)

DTIC Science & Technology

1987-01-01

20, LENGTH OF SURFACE DOWNWIND (m) LEN ..... 17 3.21 Question 21, FMW, FMV, VAP (mm Hg), BPT (deg K) ............ 17 3.22 Question 22, TIME AFTER...Temperature of stack (CC) VAP Vapor pressure (mm Hg) "VST Velocity of effluent from stack (m/sec WND Transport wind speed (m/sec) WOO Woods type, see...LEN. This is the estimated fetch of the vapor over the wetted surface of the puddle. 3.21 Question 21, FtiW, FMV, VAP (mm Hg), BPT (deg K). If the

The Stanford Automated Mounter: Pushing the limits of sample exchange at the SSRL macromolecular crystallography beamlines

DOE PAGES

Russi, Silvia; Song, Jinhu; McPhillips, Scott E.; ...

2016-02-24

The Stanford Automated Mounter System, a system for mounting and dismounting cryo-cooled crystals, has been upgraded to increase the throughput of samples on the macromolecular crystallography beamlines at the Stanford Synchrotron Radiation Lightsource. This upgrade speeds up robot maneuvers, reduces the heating/drying cycles, pre-fetches samples and adds an air-knife to remove frost from the gripper arms. As a result, sample pin exchange during automated crystal quality screening now takes about 25 s, five times faster than before this upgrade.

The Stanford Automated Mounter: Pushing the limits of sample exchange at the SSRL macromolecular crystallography beamlines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russi, Silvia; Song, Jinhu; McPhillips, Scott E.

The Stanford Automated Mounter System, a system for mounting and dismounting cryo-cooled crystals, has been upgraded to increase the throughput of samples on the macromolecular crystallography beamlines at the Stanford Synchrotron Radiation Lightsource. This upgrade speeds up robot maneuvers, reduces the heating/drying cycles, pre-fetches samples and adds an air-knife to remove frost from the gripper arms. As a result, sample pin exchange during automated crystal quality screening now takes about 25 s, five times faster than before this upgrade.

Demand Controlled Economizer Cycles: A Direct Digital Control Scheme for Heating, Ventilating, and Air Conditioning Systems,

DTIC Science & Technology

1984-05-01

Control Ignored any error of 1/10th degree or less. This was done by setting the error term E and the integral sum PREINT to zero If then absolute value of...signs of two errors jeq tdiff if equal, jump clr @preint else zero integal sum tdiff mov @diff,rl fetch absolute value of OAT-RAT ci rl,25 is...includes a heating coil and thermostatic control to maintain the air in this path at an elevated temperature, typically around 80 degrees Farenheit (80 F

Interspecies chimeric complementation for the generation of functional human tissues and organs in large animal hosts.

PubMed

Wu, Jun; Izpisua Belmonte, Juan Carlos

2016-06-01

The past decade's rapid progress in human pluripotent stem cell (hPSC) research has generated hope for meeting the rising demand of organ donation, which remains the only effective cure for end-stage organ failure, a major cause of death worldwide. Despite the potential, generation of transplantable organs from hPSCs using in vitro differentiation is far-fetched. An in vivo interspecies chimeric complementation strategy relying on chimeric-competent hPSCs and zygote genome editing provides an auspicious alternative for providing unlimited organ source for transplantation.

Asymmetry of wind waves studied in a laboratory tank

NASA Astrophysics Data System (ADS)

Ileykin, L. A.; Donelan, M. A.; Mellen, R. H.; McLaughlin, D. J.

1995-03-01

Asymmetry of wind waves was studied in laboratory tank tinder varied wind and fetch conditions using both bispectral analysis of wave records and third-order statistics of the surface elevation. It is found skewness S (the normalized third-order moment of surface elevation describing the horizontal asymmetry waves) varies only slightly with the inverse wave u*/Cm (where u* is the air friction velocity and Cm is phase speed of the dominant waves). At the same time asymmetry A, which is determined from the Hilbert transform of the wave record and characterizes the skewness of the rate of change of surface elevation, increase consistently in magnitude with the ratio u*/Cm. This suggests that nonlinear distortion of the wave profile determined by the degree of wind forcing and is a sensitive indicator of wind-wave interaction processes. It is shown that the asymmetric profile of waves can described within the frameworks of the nonlinear nonspectral concept (Plate, 1972; Lake and Yuen, 197 according to which the wind-wave field can be represented as a coherent bound-wave system consisting mainly of dominant component w. and its harmonics propagating with the same speed C. , as observed by Ramamonjiaris and Coantic (1976). The phase shift between o). harmonics is found and shown to increase with the asymmetry of the waves.

Asymmetry of wind waves studied in a laboratory tank

NASA Astrophysics Data System (ADS)

Leykin, I. A.; Donelan, M. A.; Mellen, R. H.; McLaughlin, D. J.

Asymmetry of wind waves was studied in laboratory tank tinder varied wind and fetch conditions using both bispectral analysis of wave records and third-order statistics of the surface elevation. It is found skewness S (the normalized third-order moment of surface elevation describing the horizontal asymmetry waves) varies only slightly with the inverse wave u*/Cm (where u* is the air friction velocity and Cm is phase speed of the dominant waves). At the same time asymmetry A, which is determined from the Hilbert transform of the wave record and characterizes the skewness of the rate of change of surface elevation, increase consistently in magnitude with the ratio u*/Cm. This suggests that nonlinear distortion of the wave profile determined by the degree of wind forcing and is a sensitive indicator of wind-wave interaction processes. It is shown that the asymmetric profile of waves can described within the frameworks of the nonlinear nonspectral concept (Plate, 1972; Lake and Yuen, 197 according to which the wind-wave field can be represented as a coherent bound-wave system consisting mainly of dominant component w. and its harmonics propagating with the same speed C. , as observed by Ramamonjiaris and Coantic (1976). The phase shift between o). harmonics is found and shown to increase with the asymmetry of the waves.

Size Matters: What Are the Characteristic Source Areas for Urban Planning Strategies?

PubMed Central

Fan, Chao; Myint, Soe W.; Wang, Chenghao

2016-01-01

Urban environmental measurements and observational statistics should reflect the properties generated over an adjacent area of adequate length where homogeneity is usually assumed. The determination of this characteristic source area that gives sufficient representation of the horizontal coverage of a sensing instrument or the fetch of transported quantities is of critical importance to guide the design and implementation of urban landscape planning strategies. In this study, we aim to unify two different methods for estimating source areas, viz. the statistical correlation method commonly used by geographers for landscape fragmentation and the mechanistic footprint model by meteorologists for atmospheric measurements. Good agreement was found in the intercomparison of the estimate of source areas by the two methods, based on 2-m air temperature measurement collected using a network of weather stations. The results can be extended to shed new lights on urban planning strategies, such as the use of urban vegetation for heat mitigation. In general, a sizable patch of landscape is required in order to play an effective role in regulating the local environment, proportional to the height at which stakeholders’ interest is mainly concerned. PMID:27832111

Using LiDAR to quantify uplift of shoreline angles during late Holocene earthquakes in northwest Washington

NASA Astrophysics Data System (ADS)

Sherrod, B. L.

2014-12-01

Three reverse faults in northwestern Washington - the Seattle, Tacoma, and Birch Bay faults - experienced late Holocene earthquakes. Warped intertidal platforms in the hanging wall of each fault formed broad anticlines as a result of deformation during these three earthquakes. Estimates of past deformation rely on differencing raised shoreline features and corresponding modern features. I utilized profiles of LiDAR digital elevation models to calculate prehistoric (647 profiles) and modern shoreline angles (507 profiles) and used these angles to quantify the shape and amount of deformation of each anticline. I calculated shoreline angle elevations by visually fitting lines to modern and uplifted intertidal surfaces and adjacent shoreline cliffs. The intersection of the two fitted lines is the shoreline angle. Mean elevations of modern shoreline angles for 6 shoreline areas in northern Puget Sound and the Strait of Georgia (n=507) lie within 2-46 cm of mean tide level. Three additional shoreline areas in southern Puget Sound have modern shoreline angles closer to mean higher high water (within 22-88 cm) and lie in areas with less fetch and greater tidal range than sites in northern Puget Sound and the Straits of Georgia. A M>7 earthquake ~1.1 ka on the Seattle fault lifted a broad platform cut on sedimentary rocks out of the intertidal zone. Profiles of the platform at three locations along the western end of the Seattle fault zone define an anticline 8-10 km wide (orthogonal to the fault) with a maximum uplift during the earthquake of ~5-8 m. Another large earthquake ~1.1 ka uplifted an intertidal platform along the western part of the Tacoma fault. The raised platform formed an anticline ~10 km wide (orthogonal to the fault) with a maximum uplift of ~5 m. An earthquake ~1.2 ka raised shorelines in the hanging wall of the Birch Bay fault above an anticline observed on seismic reflection profiles near Bellingham, WA. Only part of the anticline is expressed in raised shorelines because shoreline angles are not preserved in the northern limb of the anticline. Estimated width of the anticline is ~8 km with a maximum uplift of 2.5 m. Ongoing elastic half-space modeling is intended to match profiles of each raised shoreline in order to estimate fault geometries and earthquake magnitudes required to produce the observed uplift profiles.

A Hartree-Fock Application Using UPC++ and the New DArray Library

DOE PAGES

Ozog, David; Kamil, Amir; Zheng, Yili; ...

2016-07-21

The Hartree-Fock (HF) method is the fundamental first step for incorporating quantum mechanics into many-electron simulations of atoms and molecules, and it is an important component of computational chemistry toolkits like NWChem. The GTFock code is an HF implementation that, while it does not have all the features in NWChem, represents crucial algorithmic advances that reduce communication and improve load balance by doing an up-front static partitioning of tasks, followed by work stealing whenever necessary. To enable innovations in algorithms and exploit next generation exascale systems, it is crucial to support quantum chemistry codes using expressive and convenient programming modelsmore » and runtime systems that are also efficient and scalable. Here, this paper presents an HF implementation similar to GTFock using UPC++, a partitioned global address space model that includes flexible communication, asynchronous remote computation, and a powerful multidimensional array library. UPC++ offers runtime features that are useful for HF such as active messages, a rich calculus for array operations, hardware-supported fetch-and-add, and functions for ensuring asynchronous runtime progress. We present a new distributed array abstraction, DArray, that is convenient for the kinds of random-access array updates and linear algebra operations on block-distributed arrays with irregular data ownership. Finally, we analyze the performance of atomic fetch-and-add operations (relevant for load balancing) and runtime attentiveness, then compare various techniques and optimizations for each. Our optimized implementation of HF using UPC++ and the DArrays library shows up to 20% improvement over GTFock with Global Arrays at scales up to 24,000 cores.« less

A Hartree-Fock Application Using UPC++ and the New DArray Library

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ozog, David; Kamil, Amir; Zheng, Yili

The Hartree-Fock (HF) method is the fundamental first step for incorporating quantum mechanics into many-electron simulations of atoms and molecules, and it is an important component of computational chemistry toolkits like NWChem. The GTFock code is an HF implementation that, while it does not have all the features in NWChem, represents crucial algorithmic advances that reduce communication and improve load balance by doing an up-front static partitioning of tasks, followed by work stealing whenever necessary. To enable innovations in algorithms and exploit next generation exascale systems, it is crucial to support quantum chemistry codes using expressive and convenient programming modelsmore » and runtime systems that are also efficient and scalable. Here, this paper presents an HF implementation similar to GTFock using UPC++, a partitioned global address space model that includes flexible communication, asynchronous remote computation, and a powerful multidimensional array library. UPC++ offers runtime features that are useful for HF such as active messages, a rich calculus for array operations, hardware-supported fetch-and-add, and functions for ensuring asynchronous runtime progress. We present a new distributed array abstraction, DArray, that is convenient for the kinds of random-access array updates and linear algebra operations on block-distributed arrays with irregular data ownership. Finally, we analyze the performance of atomic fetch-and-add operations (relevant for load balancing) and runtime attentiveness, then compare various techniques and optimizations for each. Our optimized implementation of HF using UPC++ and the DArrays library shows up to 20% improvement over GTFock with Global Arrays at scales up to 24,000 cores.« less

Surface Renewal: Micrometeorological Measurements Avoiding the Sonic Anemometer

NASA Astrophysics Data System (ADS)

Suvocarev, K.; Reba, M. L.; Runkle, B.

2016-12-01

Surface renewal (SR) is micrometeorological technique that has been suggested as an inexpensive alternative to eddy covariance (EC). While it was originally dependent on a calibration coefficient (α), a recent approach by Castellví (2004) showed that SR can be used as a stand-alone method where α is estimated using similarity theory. This "self-calibration" method is suitable for measuring different scalar fluxes under all stability conditions (Castellví et. al, 2008). According to the same authors, SR does not demand a sonic anemometer as only the horizontal wind speed is necessary to arrive to α values. Therefore, it is more affordable and applicable in both roughness and inertial sub-layers which makes this method less stringent to fetch requirements (Castellví, 2012). The SR method has not yet been tested when the equipment is reduced to scalar measurements and a simple anemometer (RM Young 5103 Wind Monitor Sensor). Here, our objective was to test this approach over temperature, H2O, CO2 and CH4 time series. When EC is taken as a reference for a comparison, our initial results show that all fluxes measured by SR are higher than corresponding reference fluxes. The portion of overestimation is in the range of typical values reported by SR literature. Still, more research will be done to improve its understanding as the correlation between flux measurements is very high. The SR method seems to be promising in avoiding the use of sonic anemometry (and related errors) while maintaining fewer fetch requirements and the possibility to yield observations from all wind directions.

40 CFR 94.107 - Determination of maximum test speed.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Determination of maximum test speed... Determination of maximum test speed. (a) Overview. This section specifies how to determine maximum test speed from a lug curve. This maximum test speed is used in §§ 94.105, 94.106, and § 94.109 (including the...

40 CFR 94.107 - Determination of maximum test speed.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 20 2011-07-01 2011-07-01 false Determination of maximum test speed... Determination of maximum test speed. (a) Overview. This section specifies how to determine maximum test speed from a lug curve. This maximum test speed is used in §§ 94.105, 94.106, and § 94.109 (including the...

Effects of lead structure in Bering Sea pack ice on the flight costs of wintering spectacled eiders

NASA Astrophysics Data System (ADS)

Bump, Joseph K.; Lovvorn, James R.

2004-10-01

In polar regions, sea ice is critical habitat for many marine birds and mammals. The quality of pack ice habitat depends on the duration and spacing of leads (openings in the ice), which determine access to water and air for diving endotherms, and how often and how far they must move as leads open and close. Recent warming trends have caused major changes in the extent and nature of sea ice at large scales used in climate models. However, no studies have analyzed lead structure in terms of habitat for ice-dependent endotherms, or effects of climate on ice habitat at scales relevant to their daily movements. Based on observations from an icebreaker and synthetic aperture radar (SAR) images, we developed methods to describe the dynamics and thermodynamics of lead structure relative to use by spectacled eiders ( Somateria fischeri) wintering in pack ice of the Bering Sea. By correlating lead structure with weather variables, we then used these methods to estimate changes in lead dynamics from 1945 to 2002, and effects of such changes on flight costs of the eiders. For 1991-1992, when images were available about every 3 days throughout winter, SAR images were divided among five weather regimes defined by wind speed, wind direction, and air temperature. Based on 12.5-m pixels, lead shape, compass orientation, and fetch across leads did not differ among the weather regimes. However, the five regimes differed in total area of open water, leads per unit area, and distance between leads. Lead duration was modeled based on air temperature, wind, and fetch. Estimates of mean daily flight time for eiders, based on lead duration and distance between neighboring leads, differed among regimes by 0 to 15 min. Resulting flight costs varied from 0 to 158 kJ day -1, or from 0% to 11% of estimated field metabolic rate. Over 57 winters (1945-2002), variation among years in mean daily flight time was most influenced by the north-south wind component, which determined pack divergence (lead opening) during northerly winds or pack convergence (lead closing) during southerly winds. Mean daily flight time and flight cost during winter did not differ among proposed periods of decadal-scale climate shifts in the North Pacific Ocean. Although leads in mobile pack ice constantly open and close with variations in wind, under most conditions in the Bering Sea there appeared to be a shifting-mosaic steady-state of lead availability. Long-term trends in the extent and timing of Bering Sea pack ice may have affected spectacled eiders more by altering foodweb processes than by changing flight costs relative to lead structure.

Measurements of the interaction of wave groups with shorter wind-generated waves

NASA Technical Reports Server (NTRS)

Chu, Jacob S.; Long, Steven R.; Phillips, O. M.

1992-01-01

Fields of statistically steady wind-generated waves produced in a wind wave facility were perturbed by the injection of groups of longer, mechanically generated waves with various slopes. The time histories of the surface displacements were measured at four fetches in ensembles consisting of 100 realizations of each set of experimental conditions; the data were stored and analyzed digitally. Four distinct stages in the overall interaction are identified and characterized. The properties of the wave energy front are documented, and a preliminary discussion is given of the dynamic processes involved in its formation.

Optimizing Input/Output Using Adaptive File System Policies

NASA Technical Reports Server (NTRS)

Madhyastha, Tara M.; Elford, Christopher L.; Reed, Daniel A.

1996-01-01

Parallel input/output characterization studies and experiments with flexible resource management algorithms indicate that adaptivity is crucial to file system performance. In this paper we propose an automatic technique for selecting and refining file system policies based on application access patterns and execution environment. An automatic classification framework allows the file system to select appropriate caching and pre-fetching policies, while performance sensors provide feedback used to tune policy parameters for specific system environments. To illustrate the potential performance improvements possible using adaptive file system policies, we present results from experiments involving classification-based and performance-based steering.

The energy balance of wind waves and the remote sensing problem

NASA Technical Reports Server (NTRS)

Hasselmann, K.

1972-01-01

Measurements of wave growth indicate an energy balance of the wave spectrum governed primarily by input from the atmosphere, nonlinear transfer to shorter and longer waves, and advection. The pronounced spectral peak and sharp low frequency cut-off characteristic of fetch-limited spectra are explained as a self-stabilizing feature of the nonlinear wave-wave interactions. The momentum transferred from the atmosphere to the wind waves accounts for a large part of the wind drag. These findings are relevant for remote microwave sensing of the sea surface by backscatter and passive radiometry methods.

Modification of the Geographic Corrosivity Index and its Application to Overseas Bases

DTIC Science & Technology

2008-03-01

reduction in aerosol production, possibly due to a decrease in the impact of surf hitting the shoreline. Setting the fetch rating to a value of five...Lake 0.07 0.07 Quebec Bagotville 0.11 0.11 Mirabel/Montreal 0.23 0.23 Indonesia Denpasar/Bali 9.93 9.9 Jakarta International 4.04 4.0... Indonesia 27.6 78.6 5199 250.0 1039.6 259.9 9.93 Jakarta Int’l Asia - Indonesia 27.4 79.9 5470 280.5 376.9 105.7 4.04 Kuantan Asia - Malaysia 26.9 85.7

Taming the monsters of tomorrow

NASA Astrophysics Data System (ADS)

Kupferschmidt, Kai

2018-01-01

In Mary Shelley's novel, the scientist Victor Frankenstein fears that creating a female companion to his unhappy monster could lead to a "race of devils" that could drive humanity extinct. Today, some scientists worry about scientific advances in the real world that could kill all of humanity, or at least end civilization as we know it. Some two dozen researchers at three academic centers are studying these "existential risks"—including labmade viruses, armies of nanobots, and artificial intelligence—and what can be done about them. But critics say their scenarios are far-fetched and distract from real existential dangers, including climate change and nuclear war.

Wind extremes in the North Sea basin under climate change: an ensemble study of 12 CMIP5 GCMs

NASA Astrophysics Data System (ADS)

de Winter, R.; Ruessink, G.; Sterl, A.

2012-12-01

Coastal safety may be influenced by climate change, as changes in extreme surge levels and wave extremes may increase the vulnerability of dunes and other coastal defenses. In the North Sea, an area already prone to severe flooding, these high surge levels and waves are generated by severe wind speeds during storm events. As a result of the geometry of the North Sea, not only the maximum wind speed is relevant, but also wind direction. Analyzing changes in a changing climate implies that several uncertainties need to be taken into account. First, there is the uncertainty in climate experiments, which represents the possible development of the emission of greenhouse gases. Second, there is uncertainty between the climate models that are used to analyze the effect of different climate experiments. The third uncertainty is the natural variability of the climate. When this system variability is large, small trends will be difficult to detect. The natural variability results in statistical uncertainty, especially for events with high return values. We addressed the first two types of uncertainties for extreme wind conditions in the North Sea using 12 CMIP5 GCMs. To evaluate the differences between the climate experiments, two climate experiments (rcp4.5 and rcp8.5) from 2050-2100 are compared with historical runs, running from 1950-2000. Rcp4.5 is considered to be a middle climate experiment and rcp8.5 represents high-end climate scenarios. The projections of the 12 GCMs for a given scenario illustrate model uncertainty. We focus on the North Sea basin, because changes in wind conditions could have a large impact on safety of the densely populated North Sea coast, an area that has already a high exposure to flooding. Our results show that, consistent with ERA-Interim results, the annual maximum wind speed in the historical run demonstrates large interannual variability. For the North Sea, the annual maximum wind speed is not projected to change in either rcp4.5 or rcp8.5. In fact, the differences in the 12 GCMs are larger than the difference between the three experiments. Furthermore, our results show that, the variation in direction of annual maximum wind speed is large and this precludes a firm statement on climate-change induced changes in these directions. Nonetheless, most models indicate a decrease in annual maximum wind speed from south-eastern directions and an increase from south-western and western directions. This might be caused by a poleward shift of the storm track. The amount of wind from north-west and north-north-west, wind directions that are responsible for the development of extreme storm surges in the southern part of the North Sea, are not projected to change. However, North Sea coasts that have the longest fetch for western direction, e.g. the German Bight, may encounter more often high storm surge levels and extreme waves when the annual maximum wind will indeed be more often from western direction.

Directional spectra of hurricane-generated waves in the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Hu, Kelin; Chen, Qin

2011-10-01

Hurricane-induced directional wave spectra in the Gulf of Mexico are investigated based on the measurements collected at 12 buoys during 7 hurricane events in recent years. Focusing on hurricane-generated wave spectra, we only consider the wave measurements at the buoys within eight times the radius of the hurricane maximum wind speed (Rmax) from the hurricane center. A series of numerical experiments using a third-generation spectral wave prediction model were carried out to gain insight into the mechanism controlling the directional and frequency distributions of hurricane wave energy. It is found that hurricane wave spectra are almost swell-dominated except for the right-rear quadrant of a hurricane with respect to the forward direction, where the local strong winds control the spectra. Despite the complexity of a hurricane wind field, most of the spectra are mono-modal, similar to those under fetch-limited, unidirectional winds. However, bi-modal spectra were also found in both measurements and model results. Four types of bi-modal spectra have been observed. Type I happens far away (>6 × Rmax) from a hurricane. Type II is bi-modal in frequency with significant differences in direction. It happens in the two left quadrants when the direction of hurricane winds deviates considerably from the swell direction. Type III is bi-modal in frequency in almost the same wave direction with two close peaks. It occurs when the energy of locally-generated wind-sea is only partially transferred to the swell energy by non-linear wave-wave interactions. Type IV was observed in shallow waters owing to coastal effects.

Late Quaternary transgressive large dunes on the sediment-starved Adriatic shelf

USGS Publications Warehouse

Correggiari, A.; Field, M.E.; Trincardi, F.

1996-01-01

The Adriatic epicontinental basin is a low-gradient shelf where the late-Quaternary transgressive systems tract (TST) is composed of thin parasequences of backbarrier, shoreface and offshore deposits. The facies and internal architecture of the late-Quaternary TST in the Adriatic epicontinental basin changed consistently from early transgression to late transgression reflecting: (1) fluctuations in the balance between sediment supply and accommodation increase, and (2) a progressive intensification of the oceanographic regime, driven by the transgressive widening of the basin to as much as seven times its lowstand extent. One of the consequences of this trend is that high-energy marine bedforms such as sand ridges and sand waves characterize only areas that were flooded close to the end of the late-Quaternary sea-level rise, when the wind fetch was maximum and bigger waves and stronger storm currents could form. We studied the morphology, sediment composition and sequence-stratigraphical setting of a field of asymmetric bedforms (typically 3 m high and 600 m in wavelength) in 20-24 m water depth offshore the Venice Lagoon in the sediment-starved North Adriatic shelf. The sand that forms these large dunes derived from a drowned transgressive coastal deposit reworked by marine processes. Early cementation took place over most of the dune crests limiting their activity and preventing their destruction. Both the formation and deactivation of this field of sand dunes occurred over a short time interval close to the turn-around point that separates the late-Quaternary sea-level rise and the following highstand and reflect rapid changes in the oceanographic regime of the basin.

Low-cost chlorophyll meter (LCCM): portable measuring device for leaf chlorophyll

NASA Astrophysics Data System (ADS)

Hutomo E. P., Evan; Adibawa, Marcelinus Alfasisurya S.; Prilianti, Kestrilia R.; Heriyanto, Heriyanto; Brotosudarmo, Tatas H. P.

2016-11-01

Portable leaf chlorophyll meter, named low-cost chlorophyll meter (LCCM), has been created. This device was created to help farmer determining the health condition of plant based on the greenness level of leaf surface. According to previous studies, leaf greenness with a certain amount of chlorophyll level has a direct correlation with the amount of nitrogen in the leaf that indicates health of the plant and this fact needed to provide an estimate of further measures to keep the plants healthy. Device that enables to measure the leaf color change is soil plant analysis development (SPAD) meter 502 from Konica Minolta but it is relatively expensive. To answer the need of low-cost chlorophyll scanner device, this research conducted experiment using light reflectance as the base mechanism. Reflectance system from LCCM consists of near-infrared light emitting diode (LED) and red LED as light resources and photodiode. The output from both of light resources calculated using normalized difference vegetation index (NDVI) formula as the results fetched and displayed on the smartphone application using Bluetooth communication protocol. Finally, the scanner has been made as well as the Android application named NDVI Reader. The LCCM system which has been tested on 20 sample of cassava leaf with SPAD meter as a variable control showed coefficient of determination 0.9681 and root-mean-square error (RMSE) 0.014.

Contrasts in Arctic shelf sea-ice regimes and some implications: Beaufort Sea versus Laptev Sea

USGS Publications Warehouse

Reimnitz, E.; Dethleff, D.; Nurnberg, D.

1994-01-01

The winter ice-regime of the 500 km) from the mainland than in the Beaufort Sea. As a result, the annual freeze-up does not incorporate old, deep-draft ice, and with a lack of compression, such deep-draft ice is not generated in situ, as on the Beaufort Sea shelf. The Laptev Sea has as much as 1000 km of fetch at the end of summer, when freezing storms move in and large (6 m) waves can form. Also, for the first three winter months, the polynya lies inshore at a water depth of only 10 m. Turbulence and freezing are excellent conditions for sediment entrainment by frazil and anchor ice, when compared to conditions in the short-fetched Beaufort Sea. We expect entrainment to occur yearly. Different from the intensely ice-gouged Beaufort Sea shelf, hydraulic bedforms probably dominate in the Laptev Sea. Corresponding with the large volume of ice produced, more dense water is generated in the Laptev Sea, possibly accompanied by downslope sediment transport. Thermohaline convection at the midshelf polynya, together with the reduced rate of bottom disruption by ice keels, may enhance benthic productivity and permit establishment of open-shelf benthic communities which in the Beaufort Sea can thrive only in the protection of barrier islands. Indirect evidence for high benthic productivity is found in the presence of walrus, who also require year-round open water. By contrast, lack of a suitable environment restricts walrus from the Beaufort Sea, although over 700 km farther to the south. We could speculate on other consequences of the different ice regimes in the Beaufort and Laptev Seas, but these few examples serve to point out the dangers of exptrapolating from knowledge gained in the North American Arctic to other shallow Arctic shelf settings. ?? 1994.

Risk Factors for Self-Reported Cholera Within HIV-Affected Households in Rural Haiti

PubMed Central

Cheung, Hoi Ching; Meiselbach, Mark K; Jerome, Gregory; Ternier, Ralph; Ivers, Louise C

2018-01-01

Abstract Background Cholera continues to be a major cause of morbidity and mortality worldwide and is now endemic in Haiti since first being introduced in 2010. Cholera and HIV have significant geographic overlap globally, but little is known about the clinical features and risk of cholera among HIV-infected people and their households. Methods We assessed HIV-affected households originally recruited for a randomized controlled trial of food supplements. We assessed for correlation between household and individual factors and reported history of cholera since 2010 using univariable and multivariable analyses. Results There were 352 HIV-infected household members, 32 with reported history of medically attended cholera, and 1968 other household members, 55 with reported history of medically attended cholera. Among HIV-infected individuals in this study, no variables correlated with reported history of cholera in univariable analyses. Among all household members, known HIV infection (adjusted odds ratio [AOR], 3.75; 95% CI, 2.43–5.79; P < .0001), source of income in the household (AOR, 1.82; 95% CI, 1.05–3.15; P = .034), time required to fetch water (AOR, 1.07 per 5-minute increase; 95% CI, 1.01–1.12; P = .015), and severe household food insecurity (AOR, 3.23; 95% CI, 1.25–8.34; P = .016) were correlated with reported history of cholera in a multivariable analysis. Conclusions Known HIV infection, source of household income, time required to fetch water, and severe household food insecurity were independently associated with reported history of medically attended cholera in HIV-affected households in rural Haiti. Further research is required to better understand the interactions between HIV and cholera. PMID:29942825

Crop modeling: Studying the effect of water stress on the driving forces governing plant water potential

NASA Astrophysics Data System (ADS)

van Emmerik, T. H. M.; Mirfenderesgi, G.; Bohrer, G.; Steele-Dunne, S. C.; Van De Giesen, N.

2015-12-01

Water stress is one of the most important environmental factors that influence plant water dynamics. To prevent excessive water loss and physiological damage, plants can regulate transpiration by adjusting the stomatal aperture. This enhances survival, but also reduced photosynthesis and productivity. During periods of low water availability, stomatal regulation is a trade-off between optimization of either survival or production. Water stress defence mechanisms lead to significant changes in plant dynamics, e.g. leaf and stem water content. Recent research has shown that water content in a corn canopy can change up to 30% diurnally as a result of water stress, which has a considerable influence on radar backscatter from a corn canopy [1]. This highlighted the potential of water stress detection using radar. To fully explore the potential of water stress monitoring using radar, we need to understand the driving forces governing plant water potential. For this study, the recently developed the Finite-Element Tree-Crown Hydrodynamic model version 2 (FETCH2) model is applied to a corn canopy. FETCH2 is developed to resolve the hydrodynamic processes within a plant using the porous media analogy, allowing investigation of the influence of environmental stress factors on plant dynamics such as transpiration, photosynthesis, stomatal conductance, and leaf and stem water content. The model is parameterized and evaluated using a detailed dataset obtained during a three-month field experiment in Flevoland, the Netherlands, on a corn canopy. [1] van Emmerik, T., S. Steele-Dunne, J. Judge and N. van de Giesen: "Impact of Diurnal Variation in Vegetation Water Content on Radar Backscatter of Maize During Water Stress", Geosciences and Remote Sensing, IEEE Transactions on, vol. 52, issue 7, doi: 10.1109/TGRS.2014.2386142, 2015.

Generation of Wind Waves in the Persian Gulf: A Numerical Investigation

NASA Astrophysics Data System (ADS)

Liao, Y.; Kaihatu, J. M.

2010-12-01

The Persian Gulf is a long shallow basin located between the Arabian Peninsula and Iran. Wind-wave generation processes in the region are often affected by the shamal, a strong wind caused by the passage of cold fronts over the mountains of Turkey and Kurdistan. This can set up sudden energetic wind seas, hampering marine traffic. It is not immediately clear whether present wind-wave models can predict this intense, short-term growth and evolution under these conditions. Furthermore, few wave measurements or models studies have been performed in this area. In advance of a wind-wave generation experiment to be conducted off the Qatar coast, we performed a climatological study of the wind wave environment in the Persian Gulf. Using the SWAN wave model as a baseline of the state of the art, five years (2004-2008)of wind field model hindcasts from COAMPS are used as forcing.To investigate the sensitivity of the results to bathymetry, the climatological analysis was run twice more, with refraction or wave breaking deactivated, in turn. The results do not show significant differences with and without refraction, which implies the wind-wave process in Persian Gulf is less dominated by the variation of bathymetry. However the results show that a large amount of wave is dissipated by wave breaking. Wide, flat and shallow bathymetry in Persian Gulf results in a long-fetch scenario, particularly for waves arriving from the northwest. It implies that long period wind-generated waves can be fully generated in this region. Wave height is therefore fully grown by the long-fetch condition, so as to lead in higher possibility of wave breaking and energy dissipation.

The role of landscape features and density dependence in growth and fledging rates of Piping Plovers in North Dakota, USA

USGS Publications Warehouse

Anteau, Michael J.; Wiltermuth, Mark T.; Sherfy, Mark H.; Shaffer, Terry L.; Pearse, Aaron T.

2014-01-01

For species with precocial young, survival from hatching to fledging is a key factor influencing recruitment. Furthermore, growth rates of precocial chicks are an indicator of forage quality and habitat suitability of brood-rearing areas. We examined how growth and fledging rates of Piping Plover (Charadrius melodus) chicks were influenced by landscape features, such as hatchling density (hatchlings per hectare of remotely sensed habitat [H ha-1]), island vs. mainland, and wind fetch (exposure to waves) at 2-km segments (n ¼ 15) of Lake Sakakawea, North Dakota, during 2007–2008. Hatchling growth was comparable with published estimates for other habitats. Models for fledging rate (fledged young per segment) assuming density dependence had more support (wi ¼ 96%) than those assuming density independence (wi ¼ 4%). Density-dependent processes appeared to influence fledging rate only at densities .5 H ha-1, which occurred in 19% of the segments we sampled. When areas with densities .5 H ha-1 were excluded, density-dependence and density-independence models were equally supported (wi ¼ 52% and 48%, respectively). Fledging rate declined as the wind fetch of a segment increased. Fledging rate on mainland shorelines was 4.3 times greater than that on islands. Previous work has indicated that plovers prefer islands for nesting, but our results suggest that this preference is not optimal and could lead to an ecological trap for chicks. While other researchers have found nesting-habitat requirements to be gravelly areas on exposed beaches without fine-grain substrates, our results suggest that chicks fledge at lower rates in these habitats. Thus, breeding plovers likely require complexes of these nesting habitats along with protected areas with fine, nutrient-rich substrate for foraging by hatchlings.

Empirical study on neural network based predictive techniques for automatic number plate recognition

NASA Astrophysics Data System (ADS)

Shashidhara, M. S.; Indrakumar, S. S.

2011-10-01

The objective of this study is to provide an easy, accurate and effective technology for the Bangalore city traffic control. This is based on the techniques of image processing and laser beam technology. The core concept chosen here is an image processing technology by the method of automatic number plate recognition system. First number plate is recognized if any vehicle breaks the traffic rules in the signals. The number is fetched from the database of the RTO office by the process of automatic database fetching. Next this sends the notice and penalty related information to the vehicle owner email-id and an SMS sent to vehicle owner. In this paper, we use of cameras with zooming options & laser beams to get accurate pictures further applied image processing techniques such as Edge detection to understand the vehicle, Identifying the location of the number plate, Identifying the number plate for further use, Plain plate number, Number plate with additional information, Number plates in the different fonts. Accessing the database of the vehicle registration office to identify the name and address and other information of the vehicle number. The updates to be made to the database for the recording of the violation and penalty issues. A feed forward artificial neural network is used for OCR. This procedure is particularly important for glyphs that are visually similar such as '8' and '9' and results in training sets of between 25,000 and 40,000 training samples. Over training of the neural network is prevented by Bayesian regularization. The neural network output value is set to 0.05 when the input is not desired glyph, and 0.95 for correct input.

Flexible Electrostatic Technologies for Capture and Handling, Phase 1

NASA Technical Reports Server (NTRS)

Bryan, Thomas

2015-01-01

Fundamental to many of NASA's in-space transportation missions is the capture and handling of various objects and vehicles in various orbits for servicing, debris disposal, sample retrieval, and assembly without the benefit of sufficient grapple fixtures and docking ports. To perform similar material handling tasks on Earth, pincher grippers, suction grippers, or magnetic chucks are used, but are unable to reliably grip aluminum and composite spacecraft, insulation, radiators, solar arrays, or extra-terrestrial objects in the vacuum of outer space without dedicated handles in the right places. The electronic Flexible Electrostatic Technologies for space Capture and Handling (FETCH) will enable reliable and compliant gripping (soft dock) of practically any object in various orbits or surfaces without dedicated mechanical features, very low impact capture, and built-in proximity sensing without any conventional actuators. Originally developed to handle semiconductor and glass wafers during vacuum chamber processing without contamination, the normal rigid wafer handling chucks are replaced with thin metal foil segments laminated in flexible insulation driven by commercial off-the-shelf solid state, high-voltage power supplies. Preliminary testing in NASA Marshall Space Flight Center's (MSFC's) Flat Floor Robotics Lab demonstrated compliant alignment and gripping with a full-sized, 150-lb microsat mockup and translation before a clean release with a flip of a switch. The flexible electrostatic gripper pads can be adapted to various space applications with different sizes, shapes, and foil electrode layouts even with openings through the gripper pads for addition of guidance sensors or injection of permanent adhesives. With gripping forces estimated between 0.5 and 2.5 lb/in2 or 70-300 lb/ft2 of surface contact, the FETCH can turn on and off rapidly and repeatedly to enable sample handling, soft docking, in-space assembly, precision relocation, and surface translation for accurate anchoring.

Parameter identification of JONSWAP spectrum acquired by airborne LIDAR

NASA Astrophysics Data System (ADS)

Yu, Yang; Pei, Hailong; Xu, Chengzhong

2017-12-01

In this study, we developed the first linear Joint North Sea Wave Project (JONSWAP) spectrum (JS), which involves a transformation from the JS solution to the natural logarithmic scale. This transformation is convenient for defining the least squares function in terms of the scale and shape parameters. We identified these two wind-dependent parameters to better understand the wind effect on surface waves. Due to its efficiency and high-resolution, we employed the airborne Light Detection and Ranging (LIDAR) system for our measurements. Due to the lack of actual data, we simulated ocean waves in the MATLAB environment, which can be easily translated into industrial programming language. We utilized the Longuet-Higgin (LH) random-phase method to generate the time series of wave records and used the fast Fourier transform (FFT) technique to compute the power spectra density. After validating these procedures, we identified the JS parameters by minimizing the mean-square error of the target spectrum to that of the estimated spectrum obtained by FFT. We determined that the estimation error is relative to the amount of available wave record data. Finally, we found the inverse computation of wind factors (wind speed and wind fetch length) to be robust and sufficiently precise for wave forecasting.

Falling-incident detection and throughput enhancement in a multi-camera video-surveillance system.

PubMed

Shieh, Wann-Yun; Huang, Ju-Chin

2012-09-01

For most elderly, unpredictable falling incidents may occur at the corner of stairs or a long corridor due to body frailty. If we delay to rescue a falling elder who is likely fainting, more serious consequent injury may occur. Traditional secure or video surveillance systems need caregivers to monitor a centralized screen continuously, or need an elder to wear sensors to detect falling incidents, which explicitly waste much human power or cause inconvenience for elders. In this paper, we propose an automatic falling-detection algorithm and implement this algorithm in a multi-camera video surveillance system. The algorithm uses each camera to fetch the images from the regions required to be monitored. It then uses a falling-pattern recognition algorithm to determine if a falling incident has occurred. If yes, system will send short messages to someone needs to be noticed. The algorithm has been implemented in a DSP-based hardware acceleration board for functionality proof. Simulation results show that the accuracy of falling detection can achieve at least 90% and the throughput of a four-camera surveillance system can be improved by about 2.1 times. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

Python based high-level synthesis compiler

NASA Astrophysics Data System (ADS)

Cieszewski, Radosław; Pozniak, Krzysztof; Romaniuk, Ryszard

2014-11-01

This paper presents a python based High-Level synthesis (HLS) compiler. The compiler interprets an algorithmic description of a desired behavior written in Python and map it to VHDL. FPGA combines many benefits of both software and ASIC implementations. Like software, the mapped circuit is flexible, and can be reconfigured over the lifetime of the system. FPGAs therefore have the potential to achieve far greater performance than software as a result of bypassing the fetch-decode-execute operations of traditional processors, and possibly exploiting a greater level of parallelism. Creating parallel programs implemented in FPGAs is not trivial. This article describes design, implementation and first results of created Python based compiler.

Fast restoration approach for motion blurred image based on deconvolution under the blurring paths

NASA Astrophysics Data System (ADS)

Shi, Yu; Song, Jie; Hua, Xia

2015-12-01

For the real-time motion deblurring, it is of utmost importance to get a higher processing speed with about the same image quality. This paper presents a fast Richardson-Lucy motion deblurring approach to remove motion blur which rotates blurred image under blurring paths. Hence, the computational time is reduced sharply by using one-dimensional Fast Fourier Transform in one-dimensional Richardson-Lucy method. In order to obtain accurate transformational results, interpolation method is incorporated to fetch the gray values. Experiment results demonstrate that the proposed approach is efficient and effective to reduce motion blur under the blur paths.

OpenMPI and ExxonMobil Topics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hjelm, Nathan Thomas; Pritchard, Howard Porter

These are a series of slides for a presentation for ExxonMobil's visit to Los Alamos National Laboratory. Topics covered are: Open MPI - The Release Story, MPI-3 RMA in Open MPI, MPI dynamic process management and Open MPI, and new options with CLE 6. Open MPI RMA features are: since v2.0.0 full support for the MPI-3.1 specification, support for non-contiguous datatypes, support for direct use of the RDMA capabilities of high performance networks (Cray Gemini/Aries, Infiniband), starting in v2.1.0 will have support for using network atomic operations for MPI_Fetch_and_op and MPI_Compare_and_swap, tested with MPI_THREAD_MULTIPLE.

Tests of a robust eddy correlation system for sensible heat flux

NASA Astrophysics Data System (ADS)

Blanford, J. H.; Gay, L. W.

1992-03-01

Sensible heat flux estimates from a simple, one-propeller eddy correlation system (OPEC) were compared with those from a sonic anemometer eddy correlation system (SEC). In accordance with similarity theory, the performance of the OPEC system improved with increasing height of the sensor above the surface. Flux totals from the two systems at sites with adequate fetch were in excellent agreement after frequency response corrections were applied. The propeller system appears suitable for long periods of unattended measurement. The sensible heat flux measurements can be combined with net radiation and soil heat flux measurements to estimate latent heat as a residual in the surface energy balance.

Accessing SDO data in a pipeline environment using the VSO WSDL/SOAP interface

NASA Astrophysics Data System (ADS)

Suarez Sola, F. I.; Hourcle, J. A.; Amezcua, A.; Bogart, R.; Davey, A. R.; Gurman, J. B.; Hill, F.; Hughitt, V. K.; Martens, P. C.; Spencer, J.; Vso Team

2010-12-01

As part of the Virtual Solar Observatory (VSO) effort to support the Solar Dynamics Observatory (SDO) data, the VSO has worked on bringing up to date its WSDL document and SOAP interface to make it compatible with most widely used web services core engines. (E.g. axis2, jws, etc.) In this presentation we will explore the possibilities available for searching and/or fetching data within pipeline code. We will explain some of the WSDL/VSO-SDO interface intricacies and show how the vast amount of data that is available via the VSO can be tapped via IDL, Java, Perl or C in an uncomplicated way.

Comparison: Discovery on WSMOLX and miAamics/jABC

NASA Astrophysics Data System (ADS)

Kubczak, Christian; Vitvar, Tomas; Winkler, Christian; Zaharia, Raluca; Zaremba, Maciej

This chapter compares the solutions to the SWS-Challenge discovery problems provided by DERI Galway and the joint solution from the Technical University of Dortmund and University of Postdam. The two approaches are described in depth in Chapters 10 and 13. The discovery scenario raises problems associated with making service discovery an automated process. It requires fine-grained specifications of search requests and service functionality including support for fetching dynamic information during the discovery process (e.g., shipment price). Both teams utilize semantics to describe services, service requests and data models in order to enable search at the required fine-grained level of detail.

A framework for incorporating the effects of hydrodynamic stresses on forest photosynthesis and evaporation

NASA Astrophysics Data System (ADS)

Matheny, A. M.; Bohrer, G.; Thompsen, J.; Frasson, R.; Frasson, C. D.; Ivanov, V. Y.

2012-12-01

Hydraulic limitations are known to control transpiration in forest ecosystems when the soil is drying or when the vapor pressure deficit between the air and stomata (VPD) is very large, but they can also impact stomatal apertures under conditions of adequate soil moisture and lower evaporative demand. We use the NACP flux measurements and models dataset for multiple site/model intercomparisons to evaluate the degree to which currently un-resolved high-frequency (sub-daily) hydrodynamic stresses affect the error in model prediction of latent heat flux. We find that many site-model combinations are characterized by a typical pattern of overestimation of afternoon flux and a corresponding underestimation of pre-noon flux. We hypothesize that this pattern is a result of un-resolved afternoon stomata closure due to hydrodynamic stresses. In a forest plot at the University of Michigan Biological Station, we use measurements of leaf-level stomata conductance and water potential to demonstrate that trees of similar type - mid-late successional deciduous trees - have very different hydrodynamic strategies that lead to differences in their temporal patterns of stomata conductance. We found that red oak trees continue transpiring despite a large stem-water deficit while red maple trees regulate stomata to maintain a high water potential. Red oaks, which are ring porous, are also able to access more soil water, assumingly from deeper ground layers and have higher conductivity, compared with the maples, which are diffuse porous. These differences will lead to large differences in stomata conductance and water use based on the species composition of the forest. We also demonstrate that the size and shape of the tree stem-branch system may lead to differences in the extent of hydrodynamic stress, which may change the forest respiration patterns as the forest grows and ages. We propose a framework to resolve tree hydrodynamics in global and regional models. It is based on the Finite-Elements Tree-Crown Hydrodynamics model (FETCH) combined with a statistical functional-type/hydraulic-type/size representation of the trees in the forest. Lidar and multi-spectral images of the forest can be used to obtain numerical distributions of species and size of individual tree crowns needed to initialize such simulations. FETCH simulates water flow through the tree as a simplified system of porous media conduits. It explicitly resolves spatiotemporal hydraulic stresses throughout the tree's hydraulic system that cannot be easily represented using other stomatal-conductance models. It uses a physical representation of water flow in a 3-D tree-stem-branch system assuming the xylem is a porous media. Empirical equations relate water potential at the branch-tips to stomata conductance at leaves connected to these branches. FETCH calculates the hydrodynamic stress related closure of stomata, provided the atmospheric and biological variables from the global model, and could replace the current empirical formulation for stomata adjustment based on soil moisture.

Radon-222 related influence on ambient gamma dose.

PubMed

Melintescu, A; Chambers, S D; Crawford, J; Williams, A G; Zorila, B; Galeriu, D

2018-04-03

Ambient gamma dose, radon, and rainfall have been monitored in southern Bucharest, Romania, from 2010 to 2016. The seasonal cycle of background ambient gamma dose peaked between July and October (100-105 nSv h -1 ), with minimum values in February (75-80 nSv h -1 ), the time of maximum snow cover. Based on 10 m a.g.l. radon concentrations, the ambient gamma dose increased by around 1 nSv h -1 for every 5 Bq m -3 increase in radon. Radon variability attributable to diurnal changes in atmospheric mixing contributed less than 15 nSv h -1 to the overall variability in ambient gamma dose, a factor of 4 more than synoptic timescale changes in air mass fetch. By contrast, precipitation-related enhancements of the ambient gamma dose were 15-80 nSv h -1 . To facilitate routine analysis, and account in part for occasional equipment failure, an automated method for identifying precipitation spikes in the ambient gamma dose was developed. Lastly, a simple model for predicting rainfall-related enhancement of the ambient gamma dose is tested against rainfall observations from events of contrasting duration and intensity. Results are also compared with those from previously published models of simple and complex formulation. Generally, the model performed very well. When simulations underestimated observations the absolute difference was typically less than the natural variability in ambient gamma dose arising from atmospheric mixing influences. Consequently, combined use of the automated event detection method and the simple model of this study could enable the ambient gamma dose "attention limit" (which indicates a potential radiological emergency) to be reduced from 200 to 400% above background to 25-50%. Copyright © 2018 Elsevier Ltd. All rights reserved.

CMIP5-based global wave climate projections including the entire Arctic Ocean

NASA Astrophysics Data System (ADS)

Casas-Prat, M.; Wang, X. L.; Swart, N.

2018-03-01

This study presents simulations of the global ocean wave climate corresponding to the surface winds and sea ice concentrations as simulated by five CMIP5 (Coupled Model Intercomparison Project Phase 5) climate models for the historical (1979-2005) and RCP8.5 scenario future (2081-2100) periods. To tackle the numerical complexities associated with the inclusion of the North Pole, the WAVEWATCH III (WW3) wave model was used with a customized unstructured Spherical Multi-Cell grid of ∼100 km offshore and ∼50 km along coastlines. The climate model simulated wind and sea ice data, and the corresponding WW3 simulated wave data, were evaluated against reanalysis and hindcast data. The results show that all the five sets of wave simulations projected lower waves in the North Atlantic, corresponding to decreased surface wind speeds there in the warmer climate. The selected CMIP5 models also consistently projected an increase in the surface wind speed in the Southern Hemisphere (SH) mid-high latitudes, which translates in an increase in the WW3 simulated significant wave height (Hs) there. The higher waves are accompanied with increased peak wave period and increased wave age in the East Pacific and Indian Oceans, and a significant counterclockwise rotation in the mean wave direction in the Southern Oceans. The latter is caused by more intense waves from the SH traveling equatorward and developing into swells. Future wave climate in the Arctic Ocean in summer is projected to be predominantly of mixed sea states, with the climatological mean of September maximum Hs ranging mostly 3-4 m. The new waves approaching Arctic coasts will be less fetch-limited as ice retreats since a predominantly southwards mean wave direction is projected in the surrounding seas.

Environmental and socio-economic risk modelling for Chagas disease in Bolivia.

PubMed

Mischler, Paula; Kearney, Michael; McCarroll, Jennifer C; Scholte, Ronaldo G C; Vounatsou, Penelope; Malone, John B

2012-09-01

Accurately defining disease distributions and calculating disease risk is an important step in the control and prevention of diseases. Geographical information systems (GIS) and remote sensing technologies, with maximum entropy (Maxent) ecological niche modelling computer software, were used to create predictive risk maps for Chagas disease in Bolivia. Prevalence rates were calculated from 2007 to 2009 household infection survey data for Bolivia, while environmental data were compiled from the Worldclim database and MODIS satellite imagery. Socio-economic data were obtained from the Bolivian National Institute of Statistics. Disease models identified altitudes at 500-3,500 m above the mean sea level (MSL), low annual precipitation (45-250 mm), and higher diurnal range of temperature (10-19 °C; peak 16 °C) as compatible with the biological requirements of the insect vectors. Socio-economic analyses demonstrated the importance of improved housing materials and water source. Home adobe wall materials and having to fetch drinking water from rivers or wells without pump were found to be highly related to distribution of the disease by the receiver operator characteristic (ROC) area under the curve (AUC) (0.69 AUC, 0.67 AUC and 0.62 AUC, respectively), while areas with hardwood floors demonstrated a direct negative relationship (-0.71 AUC). This study demonstrates that Maxent modelling can be used in disease prevalence and incidence studies to provide governmental agencies with an easily learned, understandable method to define areas as either high, moderate or low risk for the disease. This information may be used in resource planning, targeting and implementation. However, access to high-resolution, sub-municipality socio-economic data (e.g. census tracts) would facilitate elucidation of the relative influence of poverty-related factors on regional disease dynamics.

AN ADA LINEAR ALGEBRA PACKAGE MODELED AFTER HAL/S

NASA Technical Reports Server (NTRS)

Klumpp, A. R.

1994-01-01

This package extends the Ada programming language to include linear algebra capabilities similar to those of the HAL/S programming language. The package is designed for avionics applications such as Space Station flight software. In addition to the HAL/S built-in functions, the package incorporates the quaternion functions used in the Shuttle and Galileo projects, and routines from LINPAK that solve systems of equations involving general square matrices. Language conventions in this package follow those of HAL/S to the maximum extent practical and minimize the effort required for writing new avionics software and translating existent software into Ada. Valid numeric types in this package include scalar, vector, matrix, and quaternion declarations. (Quaternions are fourcomponent vectors used in representing motion between two coordinate frames). Single precision and double precision floating point arithmetic is available in addition to the standard double precision integer manipulation. Infix operators are used instead of function calls to define dot products, cross products, quaternion products, and mixed scalar-vector, scalar-matrix, and vector-matrix products. The package contains two generic programs: one for floating point, and one for integer. The actual component type is passed as a formal parameter to the generic linear algebra package. The procedures for solving systems of linear equations defined by general matrices include GEFA, GECO, GESL, and GIDI. The HAL/S functions include ABVAL, UNIT, TRACE, DET, INVERSE, TRANSPOSE, GET, PUT, FETCH, PLACE, and IDENTITY. This package is written in Ada (Version 1.2) for batch execution and is machine independent. The linear algebra software depends on nothing outside the Ada language except for a call to a square root function for floating point scalars (such as SQRT in the DEC VAX MATHLIB library). This program was developed in 1989, and is a copyrighted work with all copyright vested in NASA.

On the performance of surface renewal analysis to estimate sensible heat flux over two growing rice fields under the influence of regional advection

NASA Astrophysics Data System (ADS)

Castellví, F.; Snyder, R. L.

2009-09-01

SummaryHigh-frequency temperature data were recorded at one height and they were used in Surface Renewal (SR) analysis to estimate sensible heat flux during the full growing season of two rice fields located north-northeast of Colusa, CA (in the Sacramento Valley). One of the fields was seeded into a flooded paddy and the other was drill seeded before flooding. To minimize fetch requirements, the measurement height was selected to be close to the maximum expected canopy height. The roughness sub-layer depth was estimated to discriminate if the temperature data came from the inertial or roughness sub-layer. The equation to estimate the roughness sub-layer depth was derived by combining simple mixing-length theory, mixing-layer analogy, equations to account for stable atmospheric surface layer conditions, and semi-empirical canopy-architecture relationships. The potential for SR analysis as a method that operates in the full surface boundary layer was tested using data collected over growing vegetation at a site influenced by regional advection of sensible heat flux. The inputs used to estimate the sensible heat fluxes included air temperature sampled at 10 Hz, the mean and variance of the horizontal wind speed, the canopy height, and the plant area index for a given intermediate height of the canopy. Regardless of the stability conditions and measurement height above the canopy, sensible heat flux estimates using SR analysis gave results that were similar to those measured with the eddy covariance method. Under unstable cases, it was shown that the performance was sensitive to estimation of the roughness sub-layer depth. However, an expression was provided to select the crucial scale required for its estimation.

Three-dimensional computational aerodynamics in the 1980's

NASA Technical Reports Server (NTRS)

Lomax, H.

1978-01-01

The future requirements for constructing codes that can be used to compute three-dimensional flows about aerodynamic shapes should be assessed in light of the constraints imposed by future computer architectures and the reality of usable algorithms that can provide practical three-dimensional simulations. On the hardware side, vector processing is inevitable in order to meet the CPU speeds required. To cope with three-dimensional geometries, massive data bases with fetch/store conflicts and transposition problems are inevitable. On the software side, codes must be prepared that: (1) can be adapted to complex geometries, (2) can (at the very least) predict the location of laminar and turbulent boundary layer separation, and (3) will converge rapidly to sufficiently accurate solutions.

Identifying compromised systems through correlation of suspicious traffic from malware behavioral analysis

NASA Astrophysics Data System (ADS)

Camilo, Ana E. F.; Grégio, André; Santos, Rafael D. C.

2016-05-01

Malware detection may be accomplished through the analysis of their infection behavior. To do so, dynamic analysis systems run malware samples and extract their operating system activities and network traffic. This traffic may represent malware accessing external systems, either to steal sensitive data from victims or to fetch other malicious artifacts (configuration files, additional modules, commands). In this work, we propose the use of visualization as a tool to identify compromised systems based on correlating malware communications in the form of graphs and finding isomorphisms between them. We produced graphs from over 6 thousand distinct network traffic files captured during malware execution and analyzed the existing relationships among malware samples and IP addresses.

An effective write policy for software coherence schemes

NASA Technical Reports Server (NTRS)

Chen, Yung-Chin; Veidenbaum, Alexander V.

1992-01-01

The authors study the write behavior and evaluate the performance of various write strategies and buffering techniques for a MIN-based multiprocessor system using the simple software coherence scheme. Hit ratios, memory latencies, total execution time, and total write traffic are used as the performance indices. The write-through write-allocate no-fetch cache using a write-back write buffer is shown to have a better performance than both write-through and write-back caches. This type of write buffer is effective in reducing the volume as well as bursts of write traffic. On average, the use of a write-back cache reduces by 60 percent the total write traffic generated by a write-through cache.

An experimental model of an indigenous BCI based system to help disabled people to communicate

NASA Astrophysics Data System (ADS)

Kabir, Kazi Sadman; Rahman, Chowdhury M. Abid; Farayez, Araf; Ferdous, Mahbuba

2017-12-01

In this paper a Brain Computer Interface (BCI) system has been proposed to help patients suffering from motor disease, paralysis or locked in syndrome to communicate via eye blinking. In this proposed BCI system EEG data is fetched by NeuroSky Headset and then analyzed by the help of WPF (Windows Presentation Foundation) based serial monitor to detect the EEG signal when the eye gives a blink. This detection of eye blinking can be used to select predefined texts and those texts can be converted to speech. The experimental result shows that this system can be used as an effective and efficient tool to communicate through brain.

Wind-related resuspension of sediments in the Peel-Harvey Estuarine System

NASA Astrophysics Data System (ADS)

Gabrielson, J. O.; Lukatelich, R. J.

1985-02-01

Resuspension of bottom sediments accounted for 69-92% of mean deposition rates (11·6-69·3 gm -2 day -1) measured at 5 sites in the Peel-Harvey Estuarine System, Western Australia. Deposition rates at all but one of the sites were found to be correlated ( P<0·05) with a function of wind combining a fetch factor with the number of hours of winds greater than 5 ms -1 weighted by the third power of wind velocity. The exception was the only site with a cover of benthic algae ( Cladophora) during the study. Wind-related resuspension greatly affects the forms and amounts of productivity in this system.

Generation of multivariate near shore extreme wave conditions based on an extreme value copula for offshore boundary conditions.

NASA Astrophysics Data System (ADS)

Leyssen, Gert; Mercelis, Peter; De Schoesitter, Philippe; Blanckaert, Joris

2013-04-01

Near shore extreme wave conditions, used as input for numerical wave agitation simulations and for the dimensioning of coastal defense structures, need to be determined at a harbour entrance situated at the French North Sea coast. To obtain significant wave heights, the numerical wave model SWAN has been used. A multivariate approach was used to account for the joint probabilities. Considered variables are: wind velocity and direction, water level and significant offshore wave height and wave period. In a first step a univariate extreme value distribution has been determined for the main variables. By means of a technique based on the mean excess function, an appropriate member of the GPD is selected. An optimal threshold for peak over threshold selection is determined by maximum likelihood optimization. Next, the joint dependency structure for the primary random variables is modeled by an extreme value copula. Eventually the multivariate domain of variables was stratified in different classes, each of which representing a combination of variable quantiles with a joint probability, which are used for model simulation. The main variable is the wind velocity, as in the area of concern extreme wave conditions are wind driven. The analysis is repeated for 9 different wind directions. The secondary variable is water level. In shallow waters extreme waves will be directly affected by water depth. Hence the joint probability of occurrence for water level and wave height is of major importance for design of coastal defense structures. Wind velocity and water levels are only dependent for some wind directions (wind induced setup). Dependent directions are detected using a Kendall and Spearman test and appeared to be those with the longest fetch. For these directions, wind velocity and water level extreme value distributions are multivariately linked through a Gumbel Copula. These distributions are stratified into classes of which the frequency of occurrence can be calculated. For the remaining directions the univariate extreme wind velocity distribution is stratified, each class combined with 5 high water levels. The wave height at the model boundaries was taken into account by a regression with the extreme wind velocity at the offshore location. The regression line and the 95% confidence limits where combined with each class. Eventually the wave period is computed by a new regression with the significant wave height. This way 1103 synthetic events were selected and simulated with the SWAN wave model, each of which a frequency of occurrence is calculated for. Hence near shore significant wave heights are obtained with corresponding frequencies. The statistical distribution of the near shore wave heights is determined by sorting the model results in a descending order and accumulating the corresponding frequencies. This approach allows determination of conditional return periods. For example, for the imposed univariate design return periods of 100 years for significant wave height and 30 years for water level, the joint return period for a simultaneous exceedance of both conditions can be computed as 4000 years. Hence, this methodology allows for a probabilistic design of coastal defense structures.

40 CFR 63.7944 - How do I determine the maximum HAP vapor pressure of my remediation material?

Code of Federal Regulations, 2010 CFR

2010-07-01

... vapor pressure of my remediation material? 63.7944 Section 63.7944 Protection of Environment... Pollutants: Site Remediation Performance Tests § 63.7944 How do I determine the maximum HAP vapor pressure of my remediation material? (a) You must determine the maximum HAP vapor pressure of your remediation...

Prevalence and molecular characterisation of Schistosoma haematobium among primary school children in Kebbi State, Nigeria

PubMed

Umar, Shuaibu; Shinkafi, Saadatu Haruna; Hudu, Shuaibu Abdullahi; Neela, Vasanthakumari; Suresh, Kumar; Nordin, Syafinaz Amin; Malina, Osman

Schistosomiasis is the major source of morbidity in Sub-Saharan Africa and Asia. It is estimated that 207 million people are infected, of which 97% are in Africa. The aim of this study was the determining of prevalence as well as the phylogeny of S. haematobium among school children in Argungu Emirate, Kebbi State Nigeria. A total of 325 urine samples was collected from school children between 7 to 14 years. S. heamatobium eggs was examined under dissecting microscope and DNA was extracted from urine sample and COX1 gene was amplified by nested PCR. The PCR products were purified, sequenced and analysed. This study showed a prevalence of 32.09%, with male pupils having the highest prevalence. S. haematobium infections in children who fetch water in the river have 24 times higher risk of being infected while those who bath in the river have 158 times higher risk of being infected. Our sequences were phylogenetically related to S. haematobium isolate U82266 from Kenya and consistence with the predominant species in Africa. This was the first S. haematobium and S. mansoni co-infection reported in Nigeria. S. haematobium infection is prevalent among school age and significantly associated with water contact.

Environmental forcing metrics to quantify short-term foredune morphodynamics

NASA Astrophysics Data System (ADS)

Spore, N.; Conery, I.; Brodie, K. L.; Palmsten, M.

2016-12-01

Coastal foredunes evolve continuously due to competing aeolian and hydrodynamic processes. Onshore to shore-parallel winds transport sand to the dune while storm-driven surge and wave runup remove sand from the dune. Dune-growth requires periods of time when the wind exceeds a threshold velocity to initiate transport and the relative geometry of the dry beach to the wind direction to create large fetches. This study aims to derive an aeolian transport potential (ATP) metric from the precipitation, available fetch (a function of wind angle and dry-beach width), and a threshold wind speed to initiate transport. ATP is then combined with a hydrodynamic transport potential (HTP) metric, defined as the number of hours of wave impact to the foredune or upper beach, to assess the time-dependent magnitude of the forcing factors affecting morphological evolution of the foredune between monthly terrestrial lidar surveys.This study focuses on two distinctly different dune fields and their frontal or incipient dune ridges in Duck, NC at the USACE Field Research Facility (FRF): (1) an undisturbed, tall and narrow recently impacted dune with a near vertical face; and (2) an undisturbed, shorter and wider dune with gentler and more hummocky slopes. The two sites are separated by < 1km alongshore and experience similar environmental forcings due to their close proximity. We used hourly precipitation, wind, wave, and imagery-derived runup data from the FRF and surrounding weather stations as inputs to ATP and HTP for each site. We scanned each site at monthly intervals for 18 months with high-resolution terrestrial lidar and generated 10 cm digital elevation models (DEM) for each scan. Incremental and cumulative changes in elevation, volume, and dune toe position were extracted from the DEMs and compared to the ATP and HTP values between the surveys to evaluate the dominant factors affecting sediment flux to the system.

Interpreting Carbon Fluxes from a Spatially Heterogeneous Peatland with Thawing Permafrost: Scaling from Plant Community Scale to Ecosystem Scale

NASA Astrophysics Data System (ADS)

Harder, S. R.; Roulet, N. T.; Strachan, I. B.; Crill, P. M.; Persson, A.; Pelletier, L.; Watt, C.

2014-12-01

Various microforms, created by spatial differential thawing of permafrost, make up the subarctic heterogeneous Stordalen peatland complex (68°22'N, 19°03'E), near Abisko, Sweden. This results in significantly different peatland vegetation communities across short distances, as well as differences in wetness, temperature and peat substrates. We have been measuring the spatially integrated CO2, heat and water vapour fluxes from this peatland complex using eddy covariance and the CO2 exchange from specific plant communities within the EC tower footprint since spring 2008. With this data we are examining if it is possible to derive the spatially integrated ecosystem-wide fluxes from community-level simple light use efficiency (LUE) and ecosystem respiration (ER) models. These models have been developed using several years of continuous autochamber flux measurements for the three major plant functional types (PFTs) as well as knowledge of the spatial variability of the vegetation, water table and active layer depths. LIDAR was used to produce a 1 m resolution digital evaluation model of the complex and the spatial distribution of PFTs was obtained from concurrent high-resolution digital colour air photography trained from vegetation surveys. Continuous water table depths have been measured for four years at over 40 locations in the complex, and peat temperatures and active layer depths are surveyed every 10 days at more than 100 locations. The EC footprint is calculated for every half-hour and the PFT based models are run with the corresponding environmental variables weighted for the PFTs within the EC footprint. Our results show that the Sphagnum, palsa, and sedge PFTs have distinctly different LUE models, and that the tower fluxes are dominated by a blend of the Sphagnum and palsa PFTs. We also see a distinctly different energy partitioning between the fetches containing intact palsa and those with thawed palsa: the evaporative efficiency is higher and the Bowen ration lower for the thawed palsa fetches.

Bridging the Transition from Mesoscale to Microscale Turbulence in Numerical Weather Prediction Models

NASA Astrophysics Data System (ADS)

Muñoz-Esparza, Domingo; Kosović, Branko; Mirocha, Jeff; van Beeck, Jeroen

2014-12-01

With a focus towards developing multiscale capabilities in numerical weather prediction models, the specific problem of the transition from the mesoscale to the microscale is investigated. For that purpose, idealized one-way nested mesoscale to large-eddy simulation (LES) experiments were carried out using the Weather Research and Forecasting model framework. It is demonstrated that switching from one-dimensional turbulent diffusion in the mesoscale model to three-dimensional LES mixing does not necessarily result in an instantaneous development of turbulence in the LES domain. On the contrary, very large fetches are needed for the natural transition to turbulence to occur. The computational burden imposed by these long fetches necessitates the development of methods to accelerate the generation of turbulence on a nested LES domain forced by a smooth mesoscale inflow. To that end, four new methods based upon finite amplitude perturbations of the potential temperature field along the LES inflow boundaries are developed, and investigated under convective conditions. Each method accelerated the development of turbulence within the LES domain, with two of the methods resulting in a rapid generation of production and inertial range energy content associated to microscales that is consistent with non-nested simulations using periodic boundary conditions. The cell perturbation approach, the simplest and most efficient of the best performing methods, was investigated further under neutral and stable conditions. Successful results were obtained in all the regimes, where satisfactory agreement of mean velocity, variances and turbulent fluxes, as well as velocity and temperature spectra, was achieved with reference non-nested simulations. In contrast, the non-perturbed LES solution exhibited important energy deficits associated to a delayed establishment of fully-developed turbulence. The cell perturbation method has negligible computational cost, significantly accelerates the generation of realistic turbulence, and requires minimal parameter tuning, with the necessary information relatable to mean inflow conditions provided by the mesoscale solution.

Toxicity evaluation with the microtox® test to assess the impact of in situ oiled shoreline treatment options: natural attenuation and sediment relocation

USGS Publications Warehouse

Lee, Kenneth; Wohlgeschaffen, Gary; Tremblay, Gilles H.; Johnson, B. Thomas; Sergy, Gary A.; Prince, Roger C.; Guenette, Chantal C.; Owens, Edward H.

2003-01-01

Changes in the toxicity levels of beach sediment, nearshore water, and bottom sediment samples were monitored with the Microtox® Test to evaluate the two in situ oil spill treatment options of natural attenuation (natural recovery––no treatment) and sediment relocation (surf washing). During a series of field trials, IF-30 fuel oil was intentionally sprayed onto the surface of three mixed sediment (pebble and sand) beaches on the island of Spitsbergen, Svalbard, Norway (78°56′ N, 16°45′ E). At a low wave-energy site (Site 1 with a 3-km wind fetch), where oil was stranded within the zone of normal wave action, residual oil concentrations and beach sediment toxicity levels were significantly reduced by both options in less than five days. At Site 3, a higher wave-energy site with a 40-km wind fetch, oil was intentionally stranded on the beach face in the upper intertidal/supratidal zones, above the level of normal wave activity. At this site under these experimental conditions, sediment relocation was effective in accelerating the removal of the oil from the sediments and reducing the Microtox® Test toxicity response to background levels. In the untreated (natural attenuation) plot at this site, the fraction of residual oil remaining within the beach sediments after one year (70%) continued to generate a toxic response. Chemical and toxicological analyses of nearshore sediment and sediment-trap samples at both sites confirmed that oil and suspended mineral fines were effectively dispersed into the surrounding environment by the in situ treatments. In terms of secondary potential detrimental effects from the release of stranded oil from the beaches, the toxicity level (Microtox® Test) of adjacent nearshore sediment samples did not exceed the Canadian regulatory limit for dredged spoils destined for ocean disposal.

Two-dimensional microclimate distribution within and above a crop canopy in an arid environment: Modeling and observational studies

NASA Astrophysics Data System (ADS)

Naot, O.; Mahrer, Y.

1991-08-01

A numerical two-dimensional model based on higher-order closure assumptions is developed to simulate the horizontal microclimate distribution over an irrigated field in arid surroundings. The model considers heat, mass, momentum, and radiative fluxes in the soil-plant-atmosphere system. Its vertical domain extends through the whole planetary boundary layer. The model requires temporal solar and atmospheric radiation data, as well as temporal boundary conditions for wind-speed, air temperature, and humidity. These boundary conditions are specified by an auxiliary mesoscale model and are incorporated in the microscale model by a nudging method. Vegetation parameters (canopy height, leaf-angle orientation distribution, leaf-area index, photometric properties, root-density distribution), soil texture, and soil-hydraulic and photometric properties are considered. The model is tested using meteorological data obtained in a drip-irrigated cotton field located in an extremely arid area, where strong fetch effects are expected. Four masts located 50 m before the leading edge of the field and 10, 30, and 100 m inward from the leading edge are used to measure various meteorological parameters and their horizontal and vertical gradients. Calculated values of air and soil temperatures, wind-speed, net radiation and soil, latent, and sensible heat fluxes agreed well with measurements. Large horizontal gradients of air temperature are both observed and measured within the canopy in the first 40 m of the leading edge. Rate of evapotranspiration at both the upwind and the downwind edges of the field are higher by more than 15% of the midfield value. Model calculations show that a stable thermal stratification is maintained above the whole field for 24 h. The aerodynamic and thermal internal boundary layer (IBL) growth is proportional to the square root of the fetch. This is also the observed rate of growth of the thermal IBL over a cool sea surface.

7 CFR 3570.66 - Determining the maximum grant assistance.

Code of Federal Regulations, 2010 CFR

2010-01-01

... maximum grant assistance. (a) Responsibility. State Directors are responsible for determining the....63(b); (2) Minimum amount sufficient to provide for economic feasibility as determined in accordance...

Small scale water treatment practice and associated factors at Burie Zuria Woreda Rural Households, Northwest Ethiopia, 2015: cross sectional study.

PubMed

Belay, Hailegebriel; Dagnew, Zewdu; Abebe, Nurilign

2016-08-26

Consuming unsafe water results in infections that lead to illness or death from water borne diseases. Though there is an increasing effort from Ethiopian government to access safe water still there are households with limited access of safe water as a result, they depend on rain, well and spring water source for domestic use. However, the water treatment practice with the available technology is not studied before in the study area. This study was conducted in rural area where there was no improved water source for domestic consumption. Households' access water from rain, spring, river and well water which need some ways of action to make water safe for the intended utilization termed as treatment. Hence, the aim of this study was to assess magnitude of small scale water treatment practices and associated factors at household level in Burie zuria woreda, North West Ethiopia, 2015. Community based cross-sectional study design with multi-stage sampling technique was used to evaluate water treatment practice and associated factors among rural households in Burie Zuria Woreda. A total of 797 households included in the study. Completeness of questionnaires were checked daily and data were coded and entered into Epi-Data and transported to SPSS version 16 software package for further analysis. Binary and multivariable logistic regression models fit to identify associated factors at 95 % CI and P-value <0.05. A total of 797 out of 846 participants responded to a questionnaire with a response rate of 94.2 %. The mean age of respondents was 44.9(SD ±10.7) years. Among the total study participants, 357(44.8 %) of them were practicing small scale water treatment at household level. Methods of water treatment at household level were; chlorine, boiling and let stand and settle. Associated factors were female headed households practice water treatment than male headed households (AOR = 1.80, 95 % CI = 1.24-2.62), educational status of being literate was associated with water treatment than illiterates (AOR = 2.07, 95 % CI = 1.51-2.83), dipping of water was associated with water treatment practice than pouring from the water collection jar (AOR = 4.11, 95 % CI = 2.89-5.85) and those households more frequently fetch water were practicing water treatment than those fetch less frequently (AOR = 4.90, 95 % CI = 2.92-8.22) and (AOR = 3.76, 95 % CI = 1.97-7.18) respectively were found to be significantly associated with small scale water treatment practice at household level. Small scale water treatment at household level is still low in the study area. Females headed households, educated people, dipping from the jar and those who fetch water more than twice a day were significant factors for water treatment. Therefore females' practice should be maintained and scale up for male headed households. Those with no primary education need special emphasis to educate them on the importance of water treatment. Encourage education through non formal mechanisms for rural people are also recommended.

An electrostatic charge measurement of blowing snow particles focusing on collision frequency to the snow surface

NASA Astrophysics Data System (ADS)

Omiya, S.; Sato, A.

2010-12-01

Blowing snow particles are known to have an electrostatic charge. This charge may be a contributing factor in the formation of snow drifts and snow cornices and changing of the trajectory of blowing snow particles. These formations and phenomena can cause natural disaster such as an avalanche and a visibility deterioration, and obstruct transportation during winter season. Therefore, charging phenomenon of the blowing snow particles is an important issue in terms of not only precise understanding of the particle motion but disaster prevention. The primary factor of charge accumulation to the blowing snow particles is thought to be due to “saltation” of them. The “saltation” is one of movement forms of blowing snow: when the snow particles are transported by the wind, they repeat frictional collisions with the snow surface. In previous studies, charge-to-mass ratios measured in the field were approximately -50 to -10 μC/kg, and in the wind tunnel were approximately -0.8 to -0.1 μC/kg. While there were qualitatively consistent in sign, negative, there were huge gaps quantitatively between them. One reason of those gaps is speculated to be due to differences in fetch. In other words, the difference of the collision frequency of snow particles to the snow surface has caused the gaps. But it is merely a suggestion and that has not been confirmed. The purpose of this experiment is to measure the charge of blowing snow particles focusing on the collision frequency and clarify the relationship between them. Experiments were carried out in the cryogenic wind tunnel of Snow and Ice Research Center (NIED, JAPAN). A Faraday cage and an electrometer were used to measure the charge of snow particles. These experiments were conducted over the hard snow surface condition to prevent the erosion of the snow surface and the generation of new snow particles from the surface. The collision frequency of particle was controlled by changing the wind velocity (4.5 to 7 m/s) under the fixed fetch (12m). The number of collisions of particle was converted from the wind velocity using an equation obtained by Kosugi et al. (2004). Blowing snow particles tend to accumulate negative charges gradually with increase of the number of collisions to the snow surface. As a result, it is demonstrated that the gaps between the field values and the wind tunnel ones were due to difference of the collision frequency of snow particles. Assuming a logarithmic relationship as first approximation between the measured charges and the number of collisions, the charge-to-mass ratios will reach roughly the same value which was obtained in the field with several hundreds collisions. For instance, fetch is needed roughly 200m for blowing snow particles to gain -30 μC/kg under the following conditions: air temperature -20 degrees Celsius, wind velocity 7m/s and hard snow surface. REFERENCE: Kosugi et al., (2004): Dependence of drifting snow saltation length on snow surface hardness. Cold Reg. Sci. Technol., 39, 133-139.

30 CFR 7.87 - Test to determine the maximum fuel-air ratio.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Test to determine the maximum fuel-air ratio. 7... Use in Underground Coal Mines § 7.87 Test to determine the maximum fuel-air ratio. (a) Test procedure... range that will be used during this test. (3) While running the engine, the following shall apply: (i...

30 CFR 7.87 - Test to determine the maximum fuel-air ratio.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Test to determine the maximum fuel-air ratio. 7... Use in Underground Coal Mines § 7.87 Test to determine the maximum fuel-air ratio. (a) Test procedure... range that will be used during this test. (3) While running the engine, the following shall apply: (i...

30 CFR 7.87 - Test to determine the maximum fuel-air ratio.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Test to determine the maximum fuel-air ratio. 7... Use in Underground Coal Mines § 7.87 Test to determine the maximum fuel-air ratio. (a) Test procedure... range that will be used during this test. (3) While running the engine, the following shall apply: (i...

30 CFR 7.87 - Test to determine the maximum fuel-air ratio.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Test to determine the maximum fuel-air ratio. 7... Use in Underground Coal Mines § 7.87 Test to determine the maximum fuel-air ratio. (a) Test procedure... range that will be used during this test. (3) While running the engine, the following shall apply: (i...

30 CFR 7.87 - Test to determine the maximum fuel-air ratio.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Test to determine the maximum fuel-air ratio. 7... Use in Underground Coal Mines § 7.87 Test to determine the maximum fuel-air ratio. (a) Test procedure... range that will be used during this test. (3) While running the engine, the following shall apply: (i...

Long-term Lake Evaporation Measurements in Southeastern Brazil

NASA Astrophysics Data System (ADS)

Dias, N. L.; Cancelli, D. M.

2007-05-01

We report here for the first time the results of a long-term (37 months) campaign of lake evaporation measurements with the eddy-covariance (EC) method. The measurements were made at Furnas Lake, a large lake (1440 km2) in Southeastern Brazil (20° 44'S, 45° 58'W and 771.8 m ASL). Mean and maximum depths at the Maximum Normal Operating Level are 13 m and 90 m respectively. Taking advantage of a long drought during 2000--2001, a large metal tower was erected over the lake's dry bed. After the water level recovered, we were left with a stable platform for performing EC measurements in one of the lake's many basins. Fetch conditions over the prevailing wind directions were excellent (1000 m from the North, and more than 3000 m from the East), with the closest land at 420 m (from NE) and 440 m (from SW). Measurements included hourly means of water surface temperature, air temperature, specific humidity, downwelling solar radiation, net radiation, wind speed, and wind direction. 10-Hz eddy covariance measurements were made of turbulent fluctuations of 3 wind components, sonic virtual temperature, air temperature (with a fine-wire thermocouple) and of fluctuating specific humidity with a specially adapted capacitive hygrometer. The validation of this sensor to measure latent heat fluxes at high frequency was made on intensive field campaigns that deployed state-of-the art Ultra-Violet and Infra-Red fast-response hygrometers. Our data analysis indicates that atmospheric stability can be far from neutral, and that it plays a very important role in the mass-transfer and heat-transfer equations for the water vapor and sensible heat fluxes. We have also found that significantly different scalar roughenesses for water vapor and for sensible heat were necessary to calibrate properly the Monin-Obukhov Similarity Theory (MOST)-based transfer equations. Due to these differences, gradient-based Bowen ratios (as usually applied in the Energy Budget Bowen Ratio method in the absence of turbulence measurements) do not agree with flux-based Bowen ratios given directly by the ratio of the sensible heat flux and the latent heat flux. Finally, we give the mean monthly values for these two fluxes from July, 2003 to June, 2006 (with 5 months of missing data).

Processing-in-Memory Enabled Graphics Processors for 3D Rendering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xie, Chenhao; Song, Shuaiwen; Wang, Jing

2017-02-06

The performance of 3D rendering of Graphics Processing Unit that convents 3D vector stream into 2D frame with 3D image effects significantly impact users’ gaming experience on modern computer systems. Due to the high texture throughput in 3D rendering, main memory bandwidth becomes a critical obstacle for improving the overall rendering performance. 3D stacked memory systems such as Hybrid Memory Cube (HMC) provide opportunities to significantly overcome the memory wall by directly connecting logic controllers to DRAM dies. Based on the observation that texel fetches significantly impact off-chip memory traffic, we propose two architectural designs to enable Processing-In-Memory based GPUmore » for efficient 3D rendering.« less

Reconstruction of noisy and blurred images using blur kernel

NASA Astrophysics Data System (ADS)

Ellappan, Vijayan; Chopra, Vishal

2017-11-01

Blur is a common in so many digital images. Blur can be caused by motion of the camera and scene object. In this work we proposed a new method for deblurring images. This work uses sparse representation to identify the blur kernel. By analyzing the image coordinates Using coarse and fine, we fetch the kernel based image coordinates and according to that observation we get the motion angle of the shaken or blurred image. Then we calculate the length of the motion kernel using radon transformation and Fourier for the length calculation of the image and we use Lucy Richardson algorithm which is also called NON-Blind(NBID) Algorithm for more clean and less noisy image output. All these operation will be performed in MATLAB IDE.

Privacy-preserving discovery of topic-based events from social sensor signals: an experimental study on Twitter.

PubMed

Nguyen, Duc T; Jung, Jai E

2014-01-01

Social network services (e.g., Twitter and Facebook) can be regarded as social sensors which can capture a number of events in the society. Particularly, in terms of time and space, various smart devices have improved the accessibility to the social network services. In this paper, we present a social software platform to detect a number of meaningful events from information diffusion patterns on such social network services. The most important feature is to process the social sensor signal for understanding social events and to support users to share relevant information along the social links. The platform has been applied to fetch and cluster tweets from Twitter into relevant categories to reveal hot topics.

XRootd, disk-based, caching proxy for optimization of data access, data placement and data replication

NASA Astrophysics Data System (ADS)

Bauerdick, L. A. T.; Bloom, K.; Bockelman, B.; Bradley, D. C.; Dasu, S.; Dost, J. M.; Sfiligoi, I.; Tadel, A.; Tadel, M.; Wuerthwein, F.; Yagil, A.; Cms Collaboration

2014-06-01

Following the success of the XRootd-based US CMS data federation, the AAA project investigated extensions of the federation architecture by developing two sample implementations of an XRootd, disk-based, caching proxy. The first one simply starts fetching a whole file as soon as a file open request is received and is suitable when completely random file access is expected or it is already known that a whole file be read. The second implementation supports on-demand downloading of partial files. Extensions to the Hadoop Distributed File System have been developed to allow for an immediate fallback to network access when local HDFS storage fails to provide the requested block. Both cache implementations are in pre-production testing at UCSD.

Orthotopic bladder substitution in men revisited: identification of continence predictors.

PubMed

Koraitim, M M; Atta, M A; Foda, M K

2006-11-01

We determined the impact of the functional characteristics of the neobladder and urethral sphincter on continence results, and determined the most significant predictors of continence. A total of 88 male patients 29 to 70 years old underwent orthotopic bladder substitution with tubularized ileocecal segment (40) and detubularized sigmoid (25) or ileum (23). Uroflowmetry, cystometry and urethral pressure profilometry were performed at 13 to 36 months (mean 19) postoperatively. The correlation between urinary continence and 28 urodynamic variables was assessed. Parameters that correlated significantly with continence were entered into a multivariate analysis using a logistic regression model to determine the most significant predictors of continence. Maximum urethral closure pressure was the only parameter that showed a statistically significant correlation with diurnal continence. Nocturnal continence had not only a statistically significant positive correlation with maximum urethral closure pressure, but also statistically significant negative correlations with maximum contraction amplitude, and baseline pressure at mid and maximum capacity. Three of these 4 parameters, including maximum urethral closure pressure, maximum contraction amplitude and baseline pressure at mid capacity, proved to be significant predictors of continence on multivariate analysis. While daytime continence is determined by maximum urethral closure pressure, during the night it is the net result of 2 forces that have about equal influence but in opposite directions, that is maximum urethral closure pressure vs maximum contraction amplitude plus baseline pressure at mid capacity. Two equations were derived from the logistic regression model to predict the probability of continence after orthotopic bladder substitution, including Z1 (diurnal) = 0.605 + 0.0085 maximum urethral closure pressure and Z2 (nocturnal) = 0.841 + 0.01 [maximum urethral closure pressure - (maximum contraction amplitude + baseline pressure at mid capacity)].

14 CFR 440.7 - Determination of maximum probable loss.

Code of Federal Regulations, 2010 CFR

2010-01-01

... determine the maximum probable loss (MPL) from covered claims by a third party for bodily injury or property... licensee, or permittee, if interagency consultation may delay issuance of the MPL determination. (c... after the MPL determination is issued. Any change in financial responsibility requirements as a result...

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 34 2012-07-01 2012-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes how to determine the maximum engine power, displacement, and power density of an engine for the...

40 CFR 1042.140 - Maximum engine power, displacement, power density, and maximum in-use engine speed.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 34 2013-07-01 2013-07-01 false Maximum engine power, displacement... Maximum engine power, displacement, power density, and maximum in-use engine speed. This section describes how to determine the maximum engine power, displacement, and power density of an engine for the...

40 CFR 63.55 - Maximum achievable control technology (MACT) determinations for affected sources subject to case...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 10 2013-07-01 2013-07-01 false Maximum achievable control technology (MACT) determinations for affected sources subject to case-by-case determination of equivalent emission... Requirements for Control Technology Determinations for Major Sources in Accordance With Clean Air Act Sections...

40 CFR 63.55 - Maximum achievable control technology (MACT) determinations for affected sources subject to case...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 10 2012-07-01 2012-07-01 false Maximum achievable control technology (MACT) determinations for affected sources subject to case-by-case determination of equivalent emission... Requirements for Control Technology Determinations for Major Sources in Accordance With Clean Air Act Sections...

40 CFR 63.55 - Maximum achievable control technology (MACT) determinations for affected sources subject to case...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Maximum achievable control technology (MACT) determinations for affected sources subject to case-by-case determination of equivalent emission... Requirements for Control Technology Determinations for Major Sources in Accordance With Clean Air Act Sections...

40 CFR 63.55 - Maximum achievable control technology (MACT) determinations for affected sources subject to case...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 10 2014-07-01 2014-07-01 false Maximum achievable control technology (MACT) determinations for affected sources subject to case-by-case determination of equivalent emission... Requirements for Control Technology Determinations for Major Sources in Accordance With Clean Air Act Sections...

Wind Generated Rogue Waves in an Annular Wave Flume.

PubMed

Toffoli, A; Proment, D; Salman, H; Monbaliu, J; Frascoli, F; Dafilis, M; Stramignoni, E; Forza, R; Manfrin, M; Onorato, M

2017-04-07

We investigate experimentally the statistical properties of a wind-generated wave field and the spontaneous formation of rogue waves in an annular flume. Unlike many experiments on rogue waves where waves are mechanically generated, here the wave field is forced naturally by wind as it is in the ocean. What is unique about the present experiment is that the annular geometry of the tank makes waves propagating circularly in an unlimited-fetch condition. Within this peculiar framework, we discuss the temporal evolution of the statistical properties of the surface elevation. We show that rogue waves and heavy-tail statistics may develop naturally during the growth of the waves just before the wave height reaches a stationary condition. Our results shed new light on the formation of rogue waves in a natural environment.

Investigation of statistical parameters of the evolving wind wave field using a laser slope gauge

NASA Astrophysics Data System (ADS)

Zavadsky, A.; Shemer, L.

2017-05-01

Statistical parameters of water waves generated by wind in a small scale facility are studied using extensively a Laser Slope Gauge (LSG), in addition to conventional measuring instruments such as a wave gauge and Pitot tube. The LSG enables direct measurements of two components of the instantaneous surface slope. Long sampling duration in a relatively small experimental facility allowed accumulating records of the measured parameters containing a large number of waves. Data were accumulated for a range of wind velocities at multiple fetches. Frequency spectra of the surface elevation and of the instantaneous local slope variation measured under identical conditions are compared. Higher moments of the surface slope are presented. Information on the waves' asymmetry is retrieved from the computed skewness of the surface slope components.

Trading efficiency for effectiveness in similarity-based indexing for image databases

NASA Astrophysics Data System (ADS)

Barros, Julio E.; French, James C.; Martin, Worthy N.; Kelly, Patrick M.

1995-11-01

Image databases typically manage feature data that can be viewed as points in a feature space. Some features, however, can be better expressed as a collection of points or described by a probability distribution function (PDF) rather than as a single point. In earlier work we introduced a similarity measure and a method for indexing and searching the PDF descriptions of these items that guarantees an answer equivalent to sequential search. Unfortunately, certain properties of the data can restrict the efficiency of that method. In this paper we extend that work and examine trade-offs between efficiency and answer quality or effectiveness. These trade-offs reduce the amount of work required during a search by reducing the number of undesired items fetched without excluding an excessive number of the desired ones.

Sea ice-atmosphere interaction: Application of multispectral satellite data in polar surface energy flux estimates

NASA Technical Reports Server (NTRS)

Steffen, K.; Schweiger, A.; Maslanik, J.; Key, J.; Weaver, R.; Barry, R.

1990-01-01

The application of multi-spectral satellite data to estimate polar surface energy fluxes is addressed. To what accuracy and over which geographic areas large scale energy budgets can be estimated are investigated based upon a combination of available remote sensing and climatological data sets. The general approach was to: (1) formulate parameterization schemes for the appropriate sea ice energy budget terms based upon the remotely sensed and/or in-situ data sets; (2) conduct sensitivity analyses using as input both natural variability (observed data in regional case studies) and theoretical variability based upon energy flux model concepts; (3) assess the applicability of these parameterization schemes to both regional and basin wide energy balance estimates using remote sensing data sets; and (4) assemble multi-spectral, multi-sensor data sets for at least two regions of the Arctic Basin and possibly one region of the Antarctic. The type of data needed for a basin-wide assessment is described and the temporal coverage of these data sets are determined by data availability and need as defined by parameterization scheme. The titles of the subjects are as follows: (1) Heat flux calculations from SSM/I and LANDSAT data in the Bering Sea; (2) Energy flux estimation using passive microwave data; (3) Fetch and stability sensitivity estimates of turbulent heat flux; and (4) Surface temperature algorithm.

Nicotine can modulate the effects of the mesenchymal stem cells on neutrophils.

PubMed

Pourtayeb, Samira; Abtahi Froushani, Seyyed Meysam

2017-03-01

It has been revealed that mesenchymal stem cells (MSCs) express some of the nicotinic receptor subunits. Moreover, the crosstalk between MSCs and neutrophils is not far-fetched. Therefore, the aim of the present study is to determine the role of nicotine on the effects of MSCs on neutrophils. After the isolation of mesenchymal stem cells from the bone marrow of rats, these cells were pulsed with different concentrations of nicotine (0, 0.1, 0.5, and 1μM) for different periods (24, 48, and 72h). Then, the neutrophils were co-cultured with MSCs for 4h and the functions of neutrophils were evaluated. The obtained findings showed that MSCs pulsed with nicotine significantly enhanced the viability and the phagocytic activity of co-cultured neutrophils and simultaneously, decreased the production of reactive oxygen substances (ROS), induced by f-MLP in neutrophils, more profound than MSCs without treatment. Moreover, MSCs, pulsed with nicotine at low to moderate concentrations, preserved the respiratory burst, triggered by opsonized yeast in neutrophils. Nevertheless, a high concentration of nicotine can interfere with the latter aspect of the crosstalk between MSCs and neutrophils. The obtained data can offer a new insight into the potential mechanisms, underlying the immunomodulatory effects of nicotine. Copyright © 2016 Medical University of Bialystok. Published by Elsevier B.V. All rights reserved.

Analysis and prediction of ocean swell using instrumented buoys

NASA Technical Reports Server (NTRS)

Mettlach, Theodore; Wang, David; Wittmann, Paul

1994-01-01

During the period 20-23 September 1990, the remnants of Supertyphoon Flo moved into the central North Pacific Ocean with sustained wind speeds of 28 m/s. The strong wind and large fetch area associated with this storm generated long-period swell that propagated to the west coast of North America. National Data Buoy Center moored-buoy stations, located in a network that ranged from the Gulf of Alaska to the California Bight, provided wave spectral estimates of the swell from this storm. The greatest dominant wave periods measured were approximately 20-25 s, and significant wave heights measured ranged from 3 to 8 m. Wave spectra from an array of three nondirectional buoys are used to find the source of the long-period swell. Directional wave spectra from a heave-pitch-roll buoy are also used to make an independent estimate of the source of the swell. The ridge-line method, using time-frequency contour plots of wave spectral energy density, is used to determine the time of swell generation, which is used with the appropriate surface pressure analysis to infer the swell generation area. The diagnosed sources of the swell are also compared with nowcasts from the Global Spectral Ocean Wave Model of the Fleet Numerical Oceanography Center. A simple method of predicting the propagation of ocean swell, by applying a simple kinematic model of wave propagation to the estimated point and time source, is demonstrated.

Hydrodynamic Trait Coordination and Cost-Benefit Tradeoffs throughout the Isohydric-Anisohydric Continuum in Trees

NASA Astrophysics Data System (ADS)

Mirfenderesgi, G.; Matheny, A. M.; Bohrer, G.

2017-12-01

Whole-plant hydraulic performance depends on the integrated function of complexes of traits, such as embolism resistance and xylem anatomy, stomatal closure mechanisms, hydraulic architecture, and root properties. The diversity of such traits produces a wide range of response strategies to both short-term variation of soil moisture and VPD, and to long-term changes to climate and hydrological cycles which affect water availability. This study aims to assess the role of different hydraulic trait combinations in trees' vulnerability to limitations in soil water availability. We use a quantitative hydrodynamic modeling framework which allows studying the influence of each suits of plant hydraulic traits independently, and assess how the different trait groups interact with each other to form viable hydraulic strategies in response to reduced soil moisture availability. We utilize the advanced plant hydrodynamic model, FETCH2, which resolves plant functional hydrodynamics, using parameters that represent emergent physiological traits at the root, stem and leaf levels. FETCH2 simulates the integrated plant-level transpiration and water capacitance, provided hydraulic traits and environmental forcing. We define a multi-dimensional hydraulic "trait space" by considering a broad continuum of hydraulic traits at each of the leaf, stem, and root levels. We test the consequences of different strategies under a range of environmental conditions, representing typical wet, intermediate, and dry conditions, based on as observations in a research forest in Northern Michigan, USA. We evaluate the degree to which simulated trees suffer hydraulic failure due to cavitation, resulting in loss of xylem conductivity, or carbon starvation, through leaf water-potential-driven reduction of stomatal conductance. Our result demonstrated that risk-prone leaf strategy when combined with risk-adverse xylem traits may expose plant to the risk of hydraulic failure due to declining water potential during period of low soil moisture and high VPD. However, if this strategy is coupled with deep roots, the plant is less likely to experience water stress even during periods of low soil water availability and high evaporative demand.

A critical review on liquid-gas mass transfer models for estimating gaseous emissions from passive liquid surfaces in wastewater treatment plants.

PubMed

Prata, Ademir A; Santos, Jane M; Timchenko, Victoria; Stuetz, Richard M

2018-03-01

Emission models are useful tools for the study and management of atmospheric emissions from passive liquid surfaces in wastewater treatment plants (WWTPs), which are potential sources of odour nuisance and other environmental impacts. In this work, different theoretical and empirical models for the gas-side (k G ) and liquid-side (k L ) mass transfer coefficients in passive surfaces in WWTPs were critically reviewed and evaluated against experimental data. Wind forcing and the development of the wind-wave field, especially the occurrence of microscale wave breaking, were identified as the most important physical factors affecting mass transfer in these situations. Two approaches performed well in describing the available data for k G for water vapour. One is an empirical correlation whilst the other consists of theoretical models based on the description of the inner part of the turbulent boundary layer over a smooth flat plate. We also fit to the experimental data set a new, alternate equation for k G , whose performance was comparable to existing ones. However, these three approaches do not agree with each other in the whole range of Schmidt numbers typical for compounds found in emissions from WWTPs. As to k L , no model was able to satisfactorily explain the behaviour and the scatter observed in the whole experimental data set. Excluding two suspected biased sources, the WATER9 (US EPA, 1994. Air Emission Models for Waste and Wastewater. North Carolina, USA. EPA-453/R-94-080A) approach produced the best results among the most commonly used k L models, although still with considerably high relative errors. For this same sub-set, we propose a new, alternate approach for estimating k L , which resulted in improved performance, particularly for longer fetches. Two main gaps were found in the literature, the understanding of the evolution of the mass transfer boundary layer over liquid surfaces, and the behaviour of k L for larger fetches, especially in the range from 40 to 60 m. Copyright © 2017 Elsevier Ltd. All rights reserved.

Impact of automatic milking systems on dairy cattle producers' reports of milking labour management, milk production and milk quality.

PubMed

Tse, C; Barkema, H W; DeVries, T J; Rushen, J; Pajor, E A

2018-04-04

Automatic milking systems (AMS), or milking robots, are becoming widely accepted as a milking technology that reduces labour and increases milk yield. However, reported amount of labour saved, changes in milk yield, and milk quality when transitioning to AMS vary widely. The purpose of this study was to document the impact of adopting AMS on farms with regards to reported changes in milking labour management, milk production, milk quality, and participation in dairy herd improvement (DHI) programmes. A survey was conducted across Canada over the phone, online, and in-person. In total, 530 AMS farms were contacted between May 2014 and the end of June 2015. A total of 217 AMS producers participated in the General Survey (Part 1), resulting in a 41% response rate, and 69 of the respondents completed the more detailed follow-up questions (Part 2). On average, after adopting AMS, the number of employees (full- and part-time non-family labour combined) decreased from 2.5 to 2.0, whereas time devoted to milking-related activities decreased by 62% (from 5.2 to 2.0 h/day). Median milking frequency was 3.0 milkings/day and robots were occupied on average 77% of the day. Producers went to fetch cows a median of 2 times/day, with a median of 3 fetch cows or 4% of the herd per robot/day. Farms had a median of 2.5 failed or incomplete milkings/robot per day. Producers reported an increase in milk yield, but little effect on milk quality. Mean milk yield on AMS farms was 32.6 kg/cow day. Median bulk tank somatic cell count was 180 000 cells/ml. Median milk fat on AMS farms was 4.0% and median milk protein was 3.3%. At the time of the survey, 67% of producers were current participants of a DHI programme. Half of the producers who were not DHI participants had stopped participation after adopting AMS. Overall, this study characterized impacts of adopting AMS and may be a useful guide for making this transition.

Effect of nutrient management on soil organic carbon sequestration, fertility, and productivity under rice-wheat cropping system in semi-reclaimed sodic soils of North India.

PubMed

Gupta Choudhury, Shreyasi; Yaduvanshi, N P S; Chaudhari, S K; Sharma, D R; Sharma, D K; Nayak, D C; Singh, S K

2018-02-05

The ever shrinking agricultural land availability and the swelling demand of food for the growing population fetch our attention towards utilizing partially reclaimed sodic soils for cultivation. In the present investigation, we compared six treatments, like control (T1), existing farmers' practice (T2), balanced inorganic fertilization (T3) and combined application of green gram (Vigna radiate) with inorganic NPK (T4), green manure (Sesbania aculeate) with inorganic NPK (T5), and farmyard manure with inorganic NPK (T6), to study the influence of nutrient management on soil organic carbon sequestration and soil fertility under long-term rice-wheat cropping system along with its productivity in gypsum-amended partially reclaimed sodic soils of semi-arid sub-tropical Indian climate. On an average, combined application of organics along with fertilizer NPK (T4, T5, and T6) decreased soil pH, ESP, and BD by 3.5, 13.0, and 6.7% than FP (T2) and 3.7, 12.5, and 6.7%, than balanced inorganic fertilizer application (T3), respectively, in surface (0-20 cm). These treatments (T4, T5, and T6) also increased 14.1% N and 19.5% P availability in soil over the usual farmers' practice (FP) with an additional saving of 44.4 and 27.3% fertilizer N and P, respectively. Long-term (6 years) incorporation of organics (T4, T5, and T6) sequestered 1.5 and 2.0 times higher soil organic carbon as compared to the balanced inorganic (T3) and FP (T2) treatments, respectively. The allocation of soil organic carbon into active and passive pools determines its relative susceptibility towards oxidation. The lower active to passive ratio (1.63) in FYM-treated plots along with its potentiality of higher soil organic carbon (SOC) sequestration compared to the initial stock proved its acceptability for long-term sustenance under intensive cropping even in partially reclaimed sodic soils. Among all the treatments, T4 yielded the maximum from second year onwards. Moreover, after 6 years of continuous cultivation, the observed EWY (2011-2012) was found to be 41.9 and 33.1% higher in T4 as compared to FP (T2) and T3, respectively. Thus, for maintaining higher yield coupled with improved SOC sequestration and nutrient availability, T4 followed by T6 treatments would be the suitable options for long-term intensive rice-wheat system in partially reclaimed sodic soils of northern India.

Indigenous knowledge of zootherapeutic use among the Biate tribe of Dima Hasao District, Assam, Northeastern India

PubMed Central

2013-01-01

Background The present study addresses the use of zootherapy in the traditional healthcare system of the Biate tribe of Dima Hasao district, Assam, India. It sought to identify the different species used for zootherapeutic use with the detailed methods of usages to create awareness and contribute to the conservation and sustainable utilization of the resources. Method 15 Biate villages within the district of Dima Hasao were surveyed through semi-structured questionnaires and informal interviews. Detailed information on the uses of each animal was recorded. Species were identified using standard literature. Fidelity level (FL) was calculated to demonstrate the percentage of respondents claiming the use of a certain animal for the same major purposes. Result The study documents 34 species for the treatment of about 34 different ailments. The largest number of species reported was mammals with17 species. Maximum number of species has been reported for the treatment of diabetes and its high fidelity levels warrants in-depth studies to establish its pharmacological activity. The usages documented herein are unique to the Biate tribe. Very often, these animals are hunted and sold openly at the local markets in the lure of quick money. A 300 gm live Gekko gecko may fetch a sum of 2,50,000 Indian Rupees (INR), and smoked meat of Hoolock hoolock cost approximately 250–300 INR per kg. Animals are also hunted for its hide. The unrestricted hunting of species like Capricornis sumatraensis has almost wiped out the population within the district. Some species are also reared as pets while some are used for display as a sign of expertise in hunting. The present study has documented the usage of at least 15 animals listed in the IUCN Red List. Conclusion The study illustrates the in-depth knowledge of the Biate tribe on zootherapy. Systematic investigation to identify the active ingredient may lead to the development of new drugs, which would prompt protection of these valuable resources. PMID:23938109

AmeriFlux Measurement Component (AMC) Instrument Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reichl, Ken; Biraud, Sebastien C.

2016-04-01

An AMC system was installed at the U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) Climate Research Facility North Slope of Alaska (NSA) Barrow site, also known as NSA C1 at the ARM Data Archive, in August 2012. A second AMC system was installed at the third ARM Mobile Facility deployment at Oliktok Point, also known as NSA M1. This in situ system consists of 12 combination soil temperature and volumetric water content (VWC) reflectometers and one set of upwelling and downwelling photosynthetically active radiation (PAR) sensors, all deployed within the fetch of the Eddy Correlation Flux Measurement System.more » Soil temperature and VWC sensors placed at two depths (10 and 30 cm below the vegetation layer) at six locations (or microsites) allow soil property inhomogeneity to be monitored across a landscape.« less

An architecture for real-time vision processing

NASA Technical Reports Server (NTRS)

Chien, Chiun-Hong

1994-01-01

To study the feasibility of developing an architecture for real time vision processing, a task queue server and parallel algorithms for two vision operations were designed and implemented on an i860-based Mercury Computing System 860VS array processor. The proposed architecture treats each vision function as a task or set of tasks which may be recursively divided into subtasks and processed by multiple processors coordinated by a task queue server accessible by all processors. Each idle processor subsequently fetches a task and associated data from the task queue server for processing and posts the result to shared memory for later use. Load balancing can be carried out within the processing system without the requirement for a centralized controller. The author concludes that real time vision processing cannot be achieved without both sequential and parallel vision algorithms and a good parallel vision architecture.

AmeriFlux US-Snd Sherman Island

DOE Data Explorer

Baldocchi, Dennis [University of California, Berkeley

2016-01-01

This is the AmeriFlux version of the carbon flux data for the site US-Snd Sherman Island. Site Description - The Sherman Island site is a 38-ha peatland pasture, west of the Delta, that is owned by the state and managed by the California Department of Water Resources. The site is degraded and heavily grazed with ~100 cattle in the area that circumscribes the main field and fetch. The island has been drained and farmed since the late 1800s. The soils of the Delta overlay deep peat that was sequestered over the Holocene period as sea-level rose and flooding of archaic wetlands prevented decomposition of roots and stems. Hence, the upper 10 m of peatland has been lost to decomposition, compaction, and subsidence. Today a mineral soil overlays a peat layer, which coincides with the general depth of the water table.

Research on SEU hardening of heterogeneous Dual-Core SoC

NASA Astrophysics Data System (ADS)

Huang, Kun; Hu, Keliu; Deng, Jun; Zhang, Tao

2017-08-01

The implementation of Single-Event Upsets (SEU) hardening has various schemes. However, some of them require a lot of human, material and financial resources. This paper proposes an easy scheme on SEU hardening for Heterogeneous Dual-core SoC (HD SoC) which contains three techniques. First, the automatic Triple Modular Redundancy (TMR) technique is adopted to harden the register heaps of the processor and the instruction-fetching module. Second, Hamming codes are used to harden the random access memory (RAM). Last, a software signature technique is applied to check the programs which are running on CPU. The scheme need not to consume additional resources, and has little influence on the performance of CPU. These technologies are very mature, easy to implement and needs low cost. According to the simulation result, the scheme can satisfy the basic demand of SEU-hardening.

Spectral characteristics of the microwave emission from a wind-driven foam-covered sea

NASA Technical Reports Server (NTRS)

Webster, W. J., Jr.; Wilheit, T. T.; Gloersen, P.; Ross, D. B.

1976-01-01

Aircraft observations of the microwave emission from the wind-driven foam-covered Bering Sea substantiate earlier results and show that the combination of surface roughness and white water yields a significant microwave brightness temperature dependence on wind speed over a wide range of microwave wavelengths, with a decreasing dependence for wavelengths above 6 cm. The spectral characteristic of brightness temperature as a function of wind speed is consistent with a foam model in which the bubbles give rise to a cusped surface between the foam and the sea. In the fetch-limited situation the contribution of the wave structure at the surface appears to increase as the foam coverage decreases. Although the data show that the thin streaks are the most important part of the white water signature, there is some evidence for the contribution of whitecaps.

Encrypting Digital Camera with Automatic Encryption Key Deletion

NASA Technical Reports Server (NTRS)

Oakley, Ernest C. (Inventor)

2007-01-01

A digital video camera includes an image sensor capable of producing a frame of video data representing an image viewed by the sensor, an image memory for storing video data such as previously recorded frame data in a video frame location of the image memory, a read circuit for fetching the previously recorded frame data, an encryption circuit having an encryption key input connected to receive the previously recorded frame data from the read circuit as an encryption key, an un-encrypted data input connected to receive the frame of video data from the image sensor and an encrypted data output port, and a write circuit for writing a frame of encrypted video data received from the encrypted data output port of the encryption circuit to the memory and overwriting the video frame location storing the previously recorded frame data.

Accelerating artificial intelligence with reconfigurable computing

NASA Astrophysics Data System (ADS)

Cieszewski, Radoslaw

Reconfigurable computing is emerging as an important area of research in computer architectures and software systems. Many algorithms can be greatly accelerated by placing the computationally intense portions of an algorithm into reconfigurable hardware. Reconfigurable computing combines many benefits of both software and ASIC implementations. Like software, the mapped circuit is flexible, and can be changed over the lifetime of the system. Similar to an ASIC, reconfigurable systems provide a method to map circuits into hardware. Reconfigurable systems therefore have the potential to achieve far greater performance than software as a result of bypassing the fetch-decode-execute operations of traditional processors, and possibly exploiting a greater level of parallelism. Such a field, where there is many different algorithms which can be accelerated, is an artificial intelligence. This paper presents example hardware implementations of Artificial Neural Networks, Genetic Algorithms and Expert Systems.

Domestic dogs comprehend human communication with iconic signs.

PubMed

Kaminski, Juliane; Tempelmann, Sebastian; Call, Josep; Tomasello, Michael

2009-11-01

A key skill in early human development is the ability to comprehend communicative intentions as expressed in both nonlinguistic gestures and language. In the current studies, we confronted domestic dogs (some of whom knew many human 'words') with a task in which they had to infer the intended referent of a human's communicative act via iconic signs--specifically, replicas and photographs. Both trained and untrained dogs successfully used iconic replicas to fetch the desired item, with many doing so from the first trial. Dogs' ability to use photographs in this same situation was less consistent. Because simple matching to sample in experimental contexts typically takes hundreds of trials (and because similarity between iconic sign and target item did not predict success), we propose that dogs' skillful performance in the current task reflects important aspects of the comprehension of human communicative intentions.

Starting points and pathways in Aboriginal students' learning of number: recognising different world views

NASA Astrophysics Data System (ADS)

Treacy, Kaye; Frid, Sandra; Jacob, Lorraine

2015-09-01

This research was designed to investigate the conceptualisations and thinking strategies Indigenous Australian students use in counting tasks. Eighteen Aboriginal students, in years 1 to 11 at a remote community school, were interviewed using standard counting tasks and a `counting' task that involved fetching `maku' (witchetty grubs) to have enough to give a maku to each person in a picture. The tasks were developed with, and the interviews conducted by, an Aboriginal research assistant, to ensure appropriate cultural and language contexts. A main finding was that most of the students did not see the need to use counting to make equivalent sets, even though they were able to demonstrate standard counting skills. The findings highlight a need to further examine the world views, orientations and related mathematical concepts and processes that Indigenous students bring to school.

The Medical Gopher — A Microcomputer Based Physician Work Station

PubMed Central

McDonald, Clement J.

1984-01-01

We've developed a microcomputer medical work station intended to reduce the physician's “gopher” work of fetching, reviewing, organizing and writing that consumes his day. The system requires extensive physician interaction; so we have developed a fast and consistent menu-oriented user interface. It provides facilities for entering prescriptions, orders, problems and other medical record information and for generating flowsheets, executing reminder rules, providing ad hoc retrievals and reporting facts about drugs, tests and differential diagnoses. Each work station is connected to a central server (currently a VAX 117/80) in a network configuration, but carries all of its own programs, tables and medical records for a few hundred patients, locally. This system is tested but not yet tried. Questions remain about physician's acceptance and the true usefullness of such a work station.

NUREBASE: database of nuclear hormone receptors.

PubMed

Duarte, Jorge; Perrière, Guy; Laudet, Vincent; Robinson-Rechavi, Marc

2002-01-01

Nuclear hormone receptors are an abundant class of ligand activated transcriptional regulators, found in varying numbers in all animals. Based on our experience of managing the official nomenclature of nuclear receptors, we have developed NUREBASE, a database containing protein and DNA sequences, reviewed protein alignments and phylogenies, taxonomy and annotations for all nuclear receptors. The reviewed NUREBASE is completed by NUREBASE_DAILY, automatically updated every 24 h. Both databases are organized under a client/server architecture, with a client written in Java which runs on any platform. This client, named FamFetch, integrates a graphical interface allowing selection of families, and manipulation of phylogenies and alignments. NUREBASE sequence data is also accessible through a World Wide Web server, allowing complex queries. All information on accessing and installing NUREBASE may be found at http://www.ens-lyon.fr/LBMC/laudet/nurebase.html.

Algorithmic synthesis using Python compiler

NASA Astrophysics Data System (ADS)

Cieszewski, Radoslaw; Romaniuk, Ryszard; Pozniak, Krzysztof; Linczuk, Maciej

2015-09-01

This paper presents a python to VHDL compiler. The compiler interprets an algorithmic description of a desired behavior written in Python and translate it to VHDL. FPGA combines many benefits of both software and ASIC implementations. Like software, the programmed circuit is flexible, and can be reconfigured over the lifetime of the system. FPGAs have the potential to achieve far greater performance than software as a result of bypassing the fetch-decode-execute operations of traditional processors, and possibly exploiting a greater level of parallelism. This can be achieved by using many computational resources at the same time. Creating parallel programs implemented in FPGAs in pure HDL is difficult and time consuming. Using higher level of abstraction and High-Level Synthesis compiler implementation time can be reduced. The compiler has been implemented using the Python language. This article describes design, implementation and results of created tools.

Structural Pattern Recognition Techniques for Data Retrieval in Massive Fusion Databases

NASA Astrophysics Data System (ADS)

Vega, J.; Murari, A.; Rattá, G. A.; Castro, P.; Pereira, A.; Portas, A.

2008-03-01

Diagnostics of present day reactor class fusion experiments, like the Joint European Torus (JET), generate thousands of signals (time series and video images) in each discharge. There is a direct correspondence between the physical phenomena taking place in the plasma and the set of structural shapes (patterns) that they form in the signals: bumps, unexpected amplitude changes, abrupt peaks, periodic components, high intensity zones or specific edge contours. A major difficulty related to data analysis is the identification, in a rapid and automated way, of a set of discharges with comparable behavior, i.e. discharges with "similar" patterns. Pattern recognition techniques are efficient tools to search for similar structural forms within the database in a fast an intelligent way. To this end, classification systems must be developed to be used as indexation methods to directly fetch the more similar patterns.

Bubble Dynamics and Resulting Noise from Traveling Bubble Cavitation.

DTIC Science & Technology

1982-04-13

proportional to the gas content. The subjectivity of visual cavitation determination is evidenced by the maximum standard deviation. As mentioned before...bubble radii at the maximum radius position on the model. The point on the model where the bubble will be at its maximum volume was determined by...48 3.7 Recording Bubble Dynamics . • . * . . . . 52 3.8 Measurement of Gas Nuclei in Water 0 • 52 3 TABLE OF CONTENTS (continued) Paqe

49 CFR 190.223 - Maximum penalties.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Maximum penalties. 190.223 Section 190.223... PROCEDURES Enforcement Civil Penalties § 190.223 Maximum penalties. (a) Any person who is determined to have... except that the maximum civil penalty may not exceed $1,000,000 for any related series of violations. (b...

40 CFR 35.575 - Maximum federal share.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Maximum federal share. 35.575 Section...) § 35.575 Maximum federal share. (a) For Tribes and Intertribal Consortia eligible under § 35.573(a... the maximum federal share to 90 percent if the Regional Administrator determines that the Tribe or...

Sediment fluxes and delta evolution at Tuapaat, Disko Island, Greenland

NASA Astrophysics Data System (ADS)

Kroon, A.; Andersen, T. J.; Bendixen, M.

2013-12-01

Ice and snow and freezing temperatures have an important influence on the coastal morphodynamics in arctic polar coastal environments. Global climate changes induce many changes along the arctic coasts. Sea-levels are rising due to thermal expansion and due to an increased fresh water flux from the glaciers and land ice masses while ice coverage of the coastal waters decreases and the open water periods in summer extend. On a yearly basis, there is a strong variation over the seasons with open waters and active rivers in summer and ice-covered coastal waters and inactive rivers in winter. The coastal processes by waves and tides are thus often limited to the summer and early fall. On a daily basis, there is also a strong variation in fluvial discharges due to the daily variations in glacier melt with maximum melt in the afternoon and minimum values at night. At the same time, the actual flux of the river to the coastal bay is also influenced by the tidal phase: low tides in the afternoon will probably give the maximum plumes in the coastal waters and high tides in the early morning will reduce the input of sediments to the coastal waters to zero. The southern shore of Disko Island in western Greenland has four deltas: Igpik, Signiffik, Tuappat and Skansen. The sediments of these deltas are a mixture of sand and gravel and they are fed by melting glaciers. The Tuapaat delta is located at the end of a pro-glacial and fluvial valley at about 16 km from the glacier. The shores of the delta are reworked by waves, predominantly from southwestern (largest fetch, over 50 km), southern, and southeastern directions. The environment has a micro- to meso- tidal range with a spring tidal range of 2.7m. The morphologic changes on the delta over the last decades clearly showed an eastward migration of the main delta channel, probably due to wave-driven alongshore processes in the ice-free periods. In this presentation, we focus on quantification of sediment fluxes on the Tuapaat delta in western Greenland. We highlight the variation of the fluxes over days with changing river discharges and tidal phases. We use field observations of discharges and sediment fluxes at the lower part of the river close to the delta apex and at the delta mouth (ADV-frame and CTD-observations) during an 8 days period from neap-tide to spring-tide in July 2013. Besides, we estimate the wave impact during the period, using climatic variables and a numerical model.

A figure of merit for AMTEC electrodes

NASA Technical Reports Server (NTRS)

Underwood, M. L.; Williams, R. M.; Jeffries-Nakamura, B.; Ryan, M. A.

1991-01-01

As a method to compare the results of alkali metal thermoelectric converter (AMTEC) electrode performance measured under different conditions, an AMTEC figure of merit called ZA is proposed. This figure of merit is the ratio of the experimental maximum power for an electrode to a calculated maximum power density as determined from a recently published electrode performance model. The calculation of a maximum power density assumes that certain loss terms in the electrode can be reduced to essentially zero by improved cell design and construction, and that the electrochemical exchange current is determined from a standard value. Other losses in the electrode are considered inherent to the electrode performance. Thus, these terms remain in the determination of the calculated maximum power. A value of ZA near one, then, indicates an electrode performance near the maximum possible performance. The primary limitation of this calculation is that the small electrode effect cannot be included. This effect leads to anomalously high values of ZA. Thus, the electrode area should be reported along with the figure of merit.

Improved rice method for determining theoretical maximum density of asphalt paving mixtures

DOT National Transportation Integrated Search

1992-05-01

Rice method (ASTM D2041 ) is used for determining the theoretical maximum specific gravity of asphalt paving mixtures which is one of the main test parameters used for mix design and construction quality control. The repeatability and reproducibility...

7 CFR 51.1178 - Maximum anhydrous citric acid permissible for corresponding total soluble solids.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 2 2012-01-01 2012-01-01 false Maximum anhydrous citric acid permissible for... Sinensis (l) Osbeck) § 51.1178 Maximum anhydrous citric acid permissible for corresponding total soluble solids. For determining the grade of juice, the maximum permissible anhydrous citric acid content in...

7 CFR 51.1178 - Maximum anhydrous citric acid permissible for corresponding total soluble solids.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 2 2011-01-01 2011-01-01 false Maximum anhydrous citric acid permissible for... Sinensis (l) Osbeck) § 51.1178 Maximum anhydrous citric acid permissible for corresponding total soluble solids. For determining the grade of juice, the maximum permissible anhydrous citric acid content in...

40 CFR 63.43 - Maximum achievable control technology (MACT) determinations for constructed and reconstructed...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Maximum achievable control technology... Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES Requirements for Control Technology Determinations...

Maximum dose rate is a determinant of hypothyroidism after 131I therapy of Graves' disease but the total thyroid absorbed dose is not.

PubMed

Krohn, Thomas; Hänscheid, Heribert; Müller, Berthold; Behrendt, Florian F; Heinzel, Alexander; Mottaghy, Felix M; Verburg, Frederik A

2014-11-01

The determinants of successful (131)I therapy of Graves' disease (GD) are unclear. To relate dosimetry parameters to outcome of therapy to identify significant determinants eu- and/or hypothyroidism after (131)I therapy in patients with GD. A retrospective study in which 206 Patients with GD treated in University Hospital between November 1999 and January 2011. All received (131)I therapy aiming at a total absorbed dose to the thyroid of 250 Gy based on pre-therapeutic dosimetry. Post-therapy dosimetric thyroid measurements were performed twice daily until discharge. From these measurements, thyroid (131)I half-life, the total thyroid absorbed dose, and the maximum dose rate after (131)I administration were calculated. In all, 48.5% of patients were hypothyroid and 28.6% of patients were euthyroid after (131)I therapy. In univariate analysis, nonhyperthyroid and hyperthyroid patients only differed by sex. A lower thyroid mass, a higher activity per gram thyroid tissue, a shorter effective thyroidal (131)I half-life, and a higher maximum dose rate, but not the total thyroid absorbed dose, were significantly associated with hypothyroidism. In multivariate analysis, the maximum dose rate remained the only significant determinant of hypothyroidism (P < .001). Maximum dose rates of 2.2 Gy/h and higher were associated with a 100% hypothyroidism rate. Not the total thyroid absorbed dose, but the maximum dose rate is a determinant of successfully achieving hypothyroidism in Graves' disease. Dosimetric concepts aiming at a specific total thyroid absorbed dose will therefore require reconsideration if our data are confirmed prospectively.

Determination of the maximum MGS mounting height : phase II detailed analysis with LS-DYNA.

DOT National Transportation Integrated Search

2012-12-01

Determination of the maximum Midwest Guardrail System (MGS) mounting height was performed in two phases. : Phase I concentrated on crash testing: two full-scale crash tests were performed on the MGS with top-rail mounting heights : of 34 in. (864 mm)...

Determination of Shapes of Boattail Bodies of Revolution for Minimum Wave Drag

NASA Technical Reports Server (NTRS)

Adams, Mac C.

1951-01-01

By use of an approximate equation for the wave drag of slender bodies of revolution in a supersonic flow field, the optimum shapes of certain boattail bodies are determined for minimum wave drag. The properties of three specific families of bodies are determined, the first family consisting of bodies having a given length and base area and a contour passing through a prescribed point between the nose and base, the second family having fixed length, base area, and maximum area, and the third family having given length, volume, and base area. The method presented is easily generalized to determine minimum-wave-drag profile shapes which have contours that must pass through any prescribed number of points. According to linearized theory, the optimum profiles are found to have infinite slope at the nose but zero radius of curvature so that the bodies appear to have pointed noses, a zero slope at the body base, and no variation of wave drag with Mach number. For those bodies having a specified intermediate.diameter (that is, location and magnitude given), the maximum body diameter is shown to be larger, in general, than the specified diameter. It is also shown that, for bodies having a specified maximum diameter, the location of the maximum diameter is not arbitrary but is determined from the ratio of base diameter to maximum diameter.

Numerical model of frazil ice and suspended sediment concentrations and formation of sediment laden ice in the Kara Sea

USGS Publications Warehouse

Sherwood, C.R.

2000-01-01

A one-dimensional (vertical) numerical model of currents, mixing, frazil ice concentration, and suspended sediment concentration has been developed and applied in the shallow southeastern Kara Sea. The objective of the calculations is to determine whether conditions suitable for turbid ice formation can occur during times of rapid cooling and wind- and wave-induced sediment resuspension. Although the model uses a simplistic approach to ice particles and neglects ice-sediment interactions, the results for low-stratification, shallow (∼20-m) freeze-up conditions indicate that the coconcentrations of frazil ice and suspended sediment in the water column are similar to observed concentrations of sediment in turbid ice. This suggests that wave-induced sediment resuspension is a viable mechanism for turbid ice formation, and enrichment mechanisms proposed to explain the high concentrations of sediment in turbid ice relative to sediment concentrations in underlying water may not be necessary in energetic conditions. However, salinity stratification found near the Ob' and Yenisey Rivers damps mixing between ice-laden surface water and sediment-laden bottom water and probably limits incorporation of resuspended sediment into turbid ice until prolonged or repeated wind events mix away the stratification. Sensitivity analyses indicate that shallow (≤20 m), unstratified waters with fine bottom sediment (settling speeds of ∼1 mm s−1 or less) and long open water fetches (>25 km) are ideal conditions for resuspension.

A Global User-Driven Model for Tile Prefetching in Web Geographical Information Systems.

PubMed

Pan, Shaoming; Chong, Yanwen; Zhang, Hang; Tan, Xicheng

2017-01-01

A web geographical information system is a typical service-intensive application. Tile prefetching and cache replacement can improve cache hit ratios by proactively fetching tiles from storage and replacing the appropriate tiles from the high-speed cache buffer without waiting for a client's requests, which reduces disk latency and improves system access performance. Most popular prefetching strategies consider only the relative tile popularities to predict which tile should be prefetched or consider only a single individual user's access behavior to determine which neighbor tiles need to be prefetched. Some studies show that comprehensively considering all users' access behaviors and all tiles' relationships in the prediction process can achieve more significant improvements. Thus, this work proposes a new global user-driven model for tile prefetching and cache replacement. First, based on all users' access behaviors, a type of expression method for tile correlation is designed and implemented. Then, a conditional prefetching probability can be computed based on the proposed correlation expression mode. Thus, some tiles to be prefetched can be found by computing and comparing the conditional prefetching probability from the uncached tiles set and, similarly, some replacement tiles can be found in the cache buffer according to multi-step prefetching. Finally, some experiments are provided comparing the proposed model with other global user-driven models, other single user-driven models, and other client-side prefetching strategies. The results show that the proposed model can achieve a prefetching hit rate in approximately 10.6% ~ 110.5% higher than the compared methods.

40 CFR 75.72 - Determination of NOX mass emissions for common stack and multiple stack configurations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... the affected units as the difference between NOX mass emissions measured in the common stack and NOX... emissions using the maximum potential NOX emission rate, the maximum potential flow rate, and either the maximum potential CO2 concentration or the minimum potential O2 concentration (as applicable). The maximum...

Challenges in Defining Tsunami Wave Height

NASA Astrophysics Data System (ADS)

Stroker, K. J.; Dunbar, P. K.; Mungov, G.; Sweeney, A.; Arcos, N. P.

2017-12-01

The NOAA National Centers for Environmental Information (NCEI) and co-located World Data Service for Geophysics maintain the global tsunami archive consisting of the historical tsunami database, imagery, and raw and processed water level data. The historical tsunami database incorporates, where available, maximum wave heights for each coastal tide gauge and deep-ocean buoy that recorded a tsunami signal. These data are important because they are used for tsunami hazard assessment, model calibration, validation, and forecast and warning. There have been ongoing discussions in the tsunami community about the correct way to measure and report these wave heights. It is important to understand how these measurements might vary depending on how the data were processed and the definition of maximum wave height. On September 16, 2015, an 8.3 Mw earthquake located 48 km west of Illapel, Chile generated a tsunami that was observed all over the Pacific region. We processed the time-series water level data for 57 tide gauges that recorded this tsunami and compared the maximum wave heights determined from different definitions. We also compared the maximum wave heights from the NCEI-processed data with the heights reported by the NOAA Tsunami Warning Centers. We found that in the near field different methods of determining the maximum tsunami wave heights could result in large differences due to possible instrumental clipping. We also found that the maximum peak is usually larger than the maximum amplitude (½ peak-to-trough), but the differences for the majority of the stations were <20 cm. For this event, the maximum tsunami wave heights determined by either definition (maximum peak or amplitude) would have validated the forecasts issued by the NOAA Tsunami Warning Centers. Since there is currently only one field in the NCEI historical tsunami database to store the maximum tsunami wave height, NCEI will consider adding an additional field for the maximum peak measurement.

Challenges in Defining Tsunami Wave Heights

NASA Astrophysics Data System (ADS)

Dunbar, Paula; Mungov, George; Sweeney, Aaron; Stroker, Kelly; Arcos, Nicolas

2017-08-01

The National Oceanic and Atmospheric Administration (NOAA) National Centers for Environmental Information (NCEI) and co-located World Data Service for Geophysics maintain the global tsunami archive consisting of the historical tsunami database, imagery, and raw and processed water level data. The historical tsunami database incorporates, where available, maximum wave heights for each coastal tide gauge and deep-ocean buoy that recorded a tsunami signal. These data are important because they are used for tsunami hazard assessment, model calibration, validation, and forecast and warning. There have been ongoing discussions in the tsunami community about the correct way to measure and report these wave heights. It is important to understand how these measurements might vary depending on how the data were processed and the definition of maximum wave height. On September 16, 2015, an 8.3 M w earthquake located 48 km west of Illapel, Chile generated a tsunami that was observed all over the Pacific region. We processed the time-series water level data for 57 coastal tide gauges that recorded this tsunami and compared the maximum wave heights determined from different definitions. We also compared the maximum wave heights from the NCEI-processed data with the heights reported by the NOAA Tsunami Warning Centers. We found that in the near field different methods of determining the maximum tsunami wave heights could result in large differences due to possible instrumental clipping. We also found that the maximum peak is usually larger than the maximum amplitude (½ peak-to-trough), but the differences for the majority of the stations were <20 cm. For this event, the maximum tsunami wave heights determined by either definition (maximum peak or amplitude) would have validated the forecasts issued by the NOAA Tsunami Warning Centers. Since there is currently only one field in the NCEI historical tsunami database to store the maximum tsunami wave height for each tide gauge and deep-ocean buoy, NCEI will consider adding an additional field for the maximum peak measurement.

Sub-block motion derivation for merge mode in HEVC

NASA Astrophysics Data System (ADS)

Chien, Wei-Jung; Chen, Ying; Chen, Jianle; Zhang, Li; Karczewicz, Marta; Li, Xiang

2016-09-01

The new state-of-the-art video coding standard, H.265/HEVC, has been finalized in 2013 and it achieves roughly 50% bit rate saving compared to its predecessor, H.264/MPEG-4 AVC. In this paper, two additional merge candidates, advanced temporal motion vector predictor and spatial-temporal motion vector predictor, are developed to improve motion information prediction scheme under the HEVC structure. The proposed method allows each Prediction Unit (PU) to fetch multiple sets of motion information from multiple blocks smaller than the current PU. By splitting a large PU into sub-PUs and filling motion information for all the sub-PUs of the large PU, signaling cost of motion information could be reduced. This paper describes above-mentioned techniques in detail and evaluates their coding performance benefits based on the common test condition during HEVC development. Simulation results show that 2.4% performance improvement over HEVC can be achieved.

Trans Fat Bans and Human Freedom

PubMed Central

Resnik, David

2014-01-01

A growing body of evidence has linked consumption of trans fatty acids to cardiovascular disease. To promote public health, numerous state and local governments in the United States have banned the use of artificial trans fats in restaurant foods, and additional bans may follow. Although these policies may have a positive impact on human health, they open the door to excessive government control over food, which could restrict dietary choices, interfere with cultural, ethnic, and religious traditions, and exacerbate socioeconomic inequalities. These slippery slope concerns cannot be dismissed as far-fetched, because the social and political pressures are place to induce additional food regulations. To protect human freedom and other values, policies that significantly restrict food choices, such as bans on types of food, should be adopted only when they are supported by substantial scientific evidence, and when policies that impose fewer restrictions on freedom, such as educational campaigns and product labeling, are likely to be ineffective. PMID:20229412

Experiences with a Barista Robot, FusionBot

NASA Astrophysics Data System (ADS)

Limbu, Dilip Kumar; Tan, Yeow Kee; Wong, Chern Yuen; Jiang, Ridong; Wu, Hengxin; Li, Liyuan; Kah, Eng Hoe; Yu, Xinguo; Li, Dong; Li, Haizhou

In this paper, we describe the implemented service robot, called FusionBot. The goal of this research is to explore and demonstrate the utility of an interactive service robot in a smart home environment, thereby improving the quality of human life. The robot has four main features: 1) speech recognition, 2) object recognition, 3) object grabbing and fetching and 4) communication with a smart coffee machine. Its software architecture employs a multimodal dialogue system that integrates different components, including spoken dialog system, vision understanding, navigation and smart device gateway. In the experiments conducted during the TechFest 2008 event, the FusionBot successfully demonstrated that it could autonomously serve coffee to visitors on their request. Preliminary survey results indicate that the robot has potential to not only aid in the general robotics but also contribute towards the long term goal of intelligent service robotics in smart home environment.

Some case studies of ocean wave physical processes utilizing the GSFC airborne radar ocean wave spectrometer

NASA Technical Reports Server (NTRS)

Jackson, F. C.

1984-01-01

The NASA K sub u band Radar Ocean Wave Spectrometer (ROWS) is an experimental prototype of a possible future satellite instrument for low data rate global waves measurements. The ROWS technique, which utilizes short pulse radar altimeters in a conical scan mode near vertical incidence to map the directional slope spectrum in wave number and azimuth, is briefly described. The potential of the technique is illustrated by some specific case studies of wave physical processes utilizing the aircraft ROWS data. These include: (1) an evaluation of numerical hindcast model performance in storm sea conditions, (2) a study of fetch limited wave growth, and (3) a study of the fully developed sea state. Results of these studies, which are briefly summarized, show how directional wave spectral observations from a mobile platform can contribute enormously to our understanding of wave physical processes.

[Analysis on influential factors of Chinese medicinal herb growers' willingness to use green pesticides: evidence on Panax notoginseng production areas in Wenshan, Yunnan province].

PubMed

Qian, Yun-Xu; Yang, Yue; Zhao, Wei; Cui, Xiu-Ming; Bi, Kai-Shun

2013-10-01

The purpose of the article is to apply a binary logistic model to analyze the major factors, which influence Chinese medicinal herb growers' willingness to use green pesticides by using survey data collected in Wenshan, Yunnan Province. The results indicate that, output per capita, average pesticide cost per mu, cognition of pesticide residues, expectations on Panax notoginseng prices, cognition of pesticides' effect of pests control, cognition of P. notoginseng prices of low pesticide residues have a significant influence on growers' willingness to use green pesticides. According to the analysis above, some proposals for enhancing Chinese medicinal herb growers' willingness to use green pesticides are put forward, such as, moving toward the intensive planting systems, fetching down the pieces of green pesticides, emphasizing and propagating the advantages of green pesticides, keeping the prices of Chinese medicinal herb running at steady rates.

Effects of sea maturity on satellite altimeter measurements

NASA Technical Reports Server (NTRS)

Glazman, Roman E.; Pilorz, Stuart H.

1990-01-01

For equilibrium and near-equilibrium sea states, the wave slope variance is a function of wind speed U and of the sea maturity. The influence of both factors on the altimeter measurements of wind speed, wave height, and radar cross section is studied experimentally on the basis of 1 year's worth of Geosat altimeter observations colocated with in situ wind and wave measurements by 20 NOAA buoys. Errors and biases in altimeter wind speed and wave height measurements are investigted. A geophysically significant error trend correlated with the sea maturity is found in wind-speed measurements. This trend is explained by examining the effect of the generalized wind fetch on the curves of the observed dependence. It is concluded that unambiguous measurements of wind speed by altimeter, in a wide range of sea states, are impossible without accounting for the actual degree of wave development.

If the Design of Express Waybill Influences Customer’s Parcel-seeking?

NASA Astrophysics Data System (ADS)

Hu, Pengji; Shi, Juan

2018-03-01

Nowadays, college students have become the main flow of online-shopping, hence positioning their own buying in express bulks is getting more and more difficult. In order to figure out how to easily seek out their names on express waybill and fetch their express, an experiment is being conducted to identify on which part the students’ name shall be noticed first. 36 college students (except freshman) from 3 different majors (12 from each major) were tested with the collecting and analyzing of Dikablis by being shown pictures of 4 different express waybills with consignee information on different part of them. The analysis result from relative software shows that consignee information set at parts with larger number of fixation point and longer duration are likely to reinforce the significance of consignee information. Consequently, the consignee information is recommended to set at parts for the sake of students’ convenience.

A novel network module for medical devices.

PubMed

Chen, Ping-Yu

2008-01-01

In order to allow medical devices to upload the vital signs to a server on a network without manually configuring for end-users, a new network module is proposed. The proposed network module, called Medical Hub (MH), functions as a bridge to fetch the data from all connecting medical devices, and then upload these data to the server. When powering on, the MH can immediately establish network configuration automatically. Network Address Translation (NAT) traversal is also supported by the MH with the UPnP Internet Gateway Device (IGD) methodology. Besides the network configuration, other configuration in the MH is automatically established by using the remote management protocol TR-069. On the other hand, a mechanism for updating software automatically according to the variant connected medical device is proposed. With this mechanism, newcome medical devices can be detected and supported by the MH without manual operation.

Content-aware network storage system supporting metadata retrieval

NASA Astrophysics Data System (ADS)

Liu, Ke; Qin, Leihua; Zhou, Jingli; Nie, Xuejun

2008-12-01

Nowadays, content-based network storage has become the hot research spot of academy and corporation[1]. In order to solve the problem of hit rate decline causing by migration and achieve the content-based query, we exploit a new content-aware storage system which supports metadata retrieval to improve the query performance. Firstly, we extend the SCSI command descriptor block to enable system understand those self-defined query requests. Secondly, the extracted metadata is encoded by extensible markup language to improve the universality. Thirdly, according to the demand of information lifecycle management (ILM), we store those data in different storage level and use corresponding query strategy to retrieval them. Fourthly, as the file content identifier plays an important role in locating data and calculating block correlation, we use it to fetch files and sort query results through friendly user interface. Finally, the experiments indicate that the retrieval strategy and sort algorithm have enhanced the retrieval efficiency and precision.

Adaptive proxy map server for efficient vector spatial data rendering

NASA Astrophysics Data System (ADS)

Sayar, Ahmet

2013-01-01

The rapid transmission of vector map data over the Internet is becoming a bottleneck of spatial data delivery and visualization in web-based environment because of increasing data amount and limited network bandwidth. In order to improve both the transmission and rendering performances of vector spatial data over the Internet, we propose a proxy map server enabling parallel vector data fetching as well as caching to improve the performance of web-based map servers in a dynamic environment. Proxy map server is placed seamlessly anywhere between the client and the final services, intercepting users' requests. It employs an efficient parallelization technique based on spatial proximity and data density in case distributed replica exists for the same spatial data. The effectiveness of the proposed technique is proved at the end of the article by the application of creating map images enriched with earthquake seismic data records.

Automatic segmentation of mandible in panoramic x-ray.

PubMed

Abdi, Amir Hossein; Kasaei, Shohreh; Mehdizadeh, Mojdeh

2015-10-01

As the panoramic x-ray is the most common extraoral radiography in dentistry, segmentation of its anatomical structures facilitates diagnosis and registration of dental records. This study presents a fast and accurate method for automatic segmentation of mandible in panoramic x-rays. In the proposed four-step algorithm, a superior border is extracted through horizontal integral projections. A modified Canny edge detector accompanied by morphological operators extracts the inferior border of the mandible body. The exterior borders of ramuses are extracted through a contour tracing method based on the average model of mandible. The best-matched template is fetched from the atlas of mandibles to complete the contour of left and right processes. The algorithm was tested on a set of 95 panoramic x-rays. Evaluating the results against manual segmentations of three expert dentists showed that the method is robust. It achieved an average performance of [Formula: see text] in Dice similarity, specificity, and sensitivity.

AmeriFlux US-PFa Park Falls/WLEF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Desai, Ankur

This is the AmeriFlux version of the carbon flux data for the site US-PFa Park Falls/WLEF. Site Description - The flux footprint encompasses a highly heterogeneous landscape of upland forests and wetlands (forested and nonforested). The forests are mainly deciduous but also include substantial coniferous coverage. The upland/lowland variability occurs on spatial scales of a few hundred meters. This heterogeneous landscape is further complicated by a nonuniform, small scale mosaic of thinning and clearcutting of the forest. At larger scales (1 km or greater) the forest cover mosaic is quite homogeneous for many kilometers. The site was chosen not formore » study of a simple stand, but for upscaling experiments. The daytime fetch of flux measurements from the 396m level is on the order of 5-10 km, yielding a flux footprint roughly 100x the area of a typical stand-level flux tower. AC power (tower is a TV transmitter).« less

Trans fat bans and human freedom.

PubMed

Resnik, David

2010-03-01

A growing body of evidence has linked consumption of trans fatty acids to cardiovascular disease. To promote public health, numerous state and local governments in the United States have banned the use of artificial trans fats in restaurant foods, and additional bans may follow. Although these policies may have a positive impact on human health, they open the door to excessive government control over food, which could restrict dietary choices, interfere with cultural, ethnic, and religious traditions, and exacerbate socioeconomic inequalities. These slippery slope concerns cannot be dismissed as far-fetched, because the social and political pressures are place to induce additional food regulations. To protect human freedom and other values, policies that significantly restrict food choices, such as bans on types of food, should be adopted only when they are supported by substantial scientific evidence, and when policies that impose fewer restrictions on freedom, such as educational campaigns and product labeling, are likely to be ineffective.

Performance Simulation & Engineering Analysis/Design and Verification of a Shock Mitigation System for a Rover Landing on Mars

NASA Astrophysics Data System (ADS)

Ullio, Roberto; Gily, Alessandro; Jones, Howard; Geelen, Kelly; Larranaga, Jonan

2014-06-01

In the frame of the ESA Mars Robotic Exploration Preparation (MREP) programme and within its Technology Development Plan [1] the activity "E913- 007MM Shock Mitigation Operating Only at Touch- down by use of minimalist/dispensable Hardware" (SMOOTH) was conducted under the framework of Rover technologies and to support the ESA MREP Mars Precision Lander (MPL) Phase A system study with the objectives to:• study the behaviour of the Sample Fetching Rover (SFR) landing on Mars on its wheels• investigate and implement into the design of the SFR Locomotion Sub-System (LSS) an impact energy absorption system (SMOOTH)• verify by simulation the performances of SMOOTH The main purpose of this paper is to present the obtained numerical simulation results and to explain how these results have been utilized first to iterate on the design of the SMOOTH concept and then to validate its performances.

Implementing Artificial Intelligence Behaviors in a Virtual World

NASA Technical Reports Server (NTRS)

Krisler, Brian; Thome, Michael

2012-01-01

In this paper, we will present a look at the current state of the art in human-computer interface technologies, including intelligent interactive agents, natural speech interaction and gestural based interfaces. We describe our use of these technologies to implement a cost effective, immersive experience on a public region in Second Life. We provision our Artificial Agents as a German Shepherd Dog avatar with an external rules engine controlling the behavior and movement. To interact with the avatar, we implemented a natural language and gesture system allowing the human avatars to use speech and physical gestures rather than interacting via a keyboard and mouse. The result is a system that allows multiple humans to interact naturally with AI avatars by playing games such as fetch with a flying disk and even practicing obedience exercises using voice and gesture, a natural seeming day in the park.

Conference Digest LEOS Summer Topical Meetings 1992

DTIC Science & Technology

1992-12-09

of the circuit and determines the maximum frequency of operation. With...operating at a frequency of 335.48 MHz. The resultant timing jitter is determined by sending both pulse trains into a rotating mirror optical correlator with...length of 1.5 un and a gate width of 100 um. have a maximum transconductance of 160 mS/mm and a cut-off frequency of 10 GHz. To determine the

Flight trajectories with maximum tangential thrust in a central Newtonian field

NASA Astrophysics Data System (ADS)

Azizov, A. G.; Korshunova, N. A.

1983-07-01

The paper examines the two-dimensional problem of determining the optimal trajectories of a point moving with a limited per-second mass consumption in a central Newtonian field. It is shown that one of the cases in which the variational equations in the Meier formulation can be integrated in quadratures is motion with maximum tangential thrust. Trajectories corresponding to this motion are determined. By way of application, attention is given to the problem of determining the thrust which assures maximum kinetic energy for the point at the moment t = t1, corresponding to the mass consumption M0 - M1, where M0 and M1 are, respectively, the initial and final mass.

76 FR 38294 - Oil and Gas and Sulphur Operations in the Outer Continental Shelf-Civil Penalties

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-30

... 2009, BOEMRE performed computations to determine if it should increase the current maximum civil penalty amount of $35,000 per violation per day. After running the computations, BOEMRE determined that.... BOEMRE has been monitoring the CPI, and the computations now justify raising the maximum civil penalty...

Spectroscopic wear detector

NASA Technical Reports Server (NTRS)

Madzsar, George C. (Inventor)

1993-01-01

The elemental composition of a material exposed to hot gases and subjected to wear is determined. Atoms of an elemental species not appearing in this material are implanted in a surface at a depth based on the maximum allowable wear. The exhaust gases are spectroscopically monitored to determine the exposure of these atoms when the maximum allowable wear is reached.

40 CFR 63.7944 - How do I determine the maximum HAP vapor pressure of my remediation material?

Code of Federal Regulations, 2014 CFR

2014-07-01

... vapor pressure of my remediation material? 63.7944 Section 63.7944 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS... Pollutants: Site Remediation Performance Tests § 63.7944 How do I determine the maximum HAP vapor pressure of...

40 CFR 63.7944 - How do I determine the maximum HAP vapor pressure of my remediation material?

Code of Federal Regulations, 2012 CFR

2012-07-01

... vapor pressure of my remediation material? 63.7944 Section 63.7944 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS... Pollutants: Site Remediation Performance Tests § 63.7944 How do I determine the maximum HAP vapor pressure of...

40 CFR 63.7944 - How do I determine the maximum HAP vapor pressure of my remediation material?

Code of Federal Regulations, 2013 CFR

2013-07-01

... vapor pressure of my remediation material? 63.7944 Section 63.7944 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS... Pollutants: Site Remediation Performance Tests § 63.7944 How do I determine the maximum HAP vapor pressure of...

40 CFR 63.7944 - How do I determine the maximum HAP vapor pressure of my remediation material?

Code of Federal Regulations, 2011 CFR

2011-07-01

... vapor pressure of my remediation material? 63.7944 Section 63.7944 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS... Pollutants: Site Remediation Performance Tests § 63.7944 How do I determine the maximum HAP vapor pressure of...

Determining the accuracy of maximum likelihood parameter estimates with colored residuals

NASA Technical Reports Server (NTRS)

Morelli, Eugene A.; Klein, Vladislav

1994-01-01

An important part of building high fidelity mathematical models based on measured data is calculating the accuracy associated with statistical estimates of the model parameters. Indeed, without some idea of the accuracy of parameter estimates, the estimates themselves have limited value. In this work, an expression based on theoretical analysis was developed to properly compute parameter accuracy measures for maximum likelihood estimates with colored residuals. This result is important because experience from the analysis of measured data reveals that the residuals from maximum likelihood estimation are almost always colored. The calculations involved can be appended to conventional maximum likelihood estimation algorithms. Simulated data runs were used to show that the parameter accuracy measures computed with this technique accurately reflect the quality of the parameter estimates from maximum likelihood estimation without the need for analysis of the output residuals in the frequency domain or heuristically determined multiplication factors. The result is general, although the application studied here is maximum likelihood estimation of aerodynamic model parameters from flight test data.

25 CFR 273.4 - Policy of maximum Indian participation.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 25 Indians 1 2013-04-01 2013-04-01 false Policy of maximum Indian participation. 273.4 Section 273.4 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR INDIAN SELF-DETERMINATION AND... Policy of maximum Indian participation. The meaningful participation in all aspects of educational...

25 CFR 273.4 - Policy of maximum Indian participation.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 25 Indians 1 2012-04-01 2011-04-01 true Policy of maximum Indian participation. 273.4 Section 273.4 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR INDIAN SELF-DETERMINATION AND... Policy of maximum Indian participation. The meaningful participation in all aspects of educational...

25 CFR 273.4 - Policy of maximum Indian participation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 25 Indians 1 2011-04-01 2011-04-01 false Policy of maximum Indian participation. 273.4 Section 273.4 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR INDIAN SELF-DETERMINATION AND... Policy of maximum Indian participation. The meaningful participation in all aspects of educational...

25 CFR 273.4 - Policy of maximum Indian participation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Policy of maximum Indian participation. 273.4 Section 273.4 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR INDIAN SELF-DETERMINATION AND... Policy of maximum Indian participation. The meaningful participation in all aspects of educational...

75 FR 66193 - Post-9/11 GI Bill 2010-2011 Tuition and Fee In-State Maximums

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-27

... DEPARTMENT OF VETERANS AFFAIRS Post-9/11 GI Bill 2010-2011 Tuition and Fee In-State Maximums... advise the public of the Post-9/11 GI Bill tuition and fee in-State maximum rates for the 2010- 2011... maximum amounts listed below to determine the amounts payable for training pursued under the Post-9/11 GI...

[The maximum heart rate in the exercise test: the 220-age formula or Sheffield's table?].

PubMed

Mesquita, A; Trabulo, M; Mendes, M; Viana, J F; Seabra-Gomes, R

1996-02-01

To determine in the maximum cardiac rate in exercise test of apparently healthy individuals may be more properly estimated through 220-age formula (Astrand) or the Sheffield table. Retrospective analysis of clinical history and exercises test of apparently healthy individuals submitted to cardiac check-up. Sequential sampling of 170 healthy individuals submitted to cardiac check-up between April 1988 and September 1992. Comparison of maximum cardiac rate of individuals studied by the protocols of Bruce and modified Bruce, in interrupted exercise test by fatigue, and with the estimated values by the formulae: 220-age versus Sheffield table. The maximum cardiac heart rate is similar with both protocols. This parameter in normal individuals is better predicted by the 220-age formula. The theoretic maximum cardiac heart rate determined by 220-age formula should be recommended for a healthy, and for this reason the Sheffield table has been excluded from our clinical practice.

Maximum Range of a Projectile Thrown from Constant-Speed Circular Motion

NASA Astrophysics Data System (ADS)

Poljak, Nikola

2016-11-01

The problem of determining the angle θ at which a point mass launched from ground level with a given speed v0 will reach a maximum distance is a standard exercise in mechanics. There are many possible ways of solving this problem, leading to the well-known answer of θ = π/4, producing a maximum range of D max = v0 2 / g , with g being the free-fall acceleration. Conceptually and calculationally more difficult problems have been suggested to improve student proficiency in projectile motion, with the most famous example being the Tarzan swing problem. The problem of determining the maximum distance of a point mass thrown from constant-speed circular motion is presented and analyzed in detail in this text. The calculational results confirm several conceptually derived conclusions regarding the initial throw position and provide some details on the angles and the way of throwing (underhand or overhand) that produce the maximum throw distance.

Factors affecting sustainability of rural water schemes in Swaziland

NASA Astrophysics Data System (ADS)

Peter, Graciana; Nkambule, Sizwe E.

The Millennium Development Goal (MDG) target to reduce the proportion of people without sustainable access to safe drinking water by the year 2015 has been met as of 2010, but huge disparities exist. Some regions, particularly Sub-Saharan Africa are lagging behind it is also in this region where up to 30% of the rural schemes are not functional at any given time. There is need for more studies on factors affecting sustainability and necessary measures which when implemented will improve the sustainability of rural water schemes. The main objective of this study was to assess the main factors affecting the sustainability of rural water schemes in Swaziland using a Multi-Criteria Analysis Approach. The main factors considered were: financial, social, technical, environmental and institutional. The study was done in Lubombo region. Fifteen functional water schemes in 11 communities were studied. Data was collected using questionnaires, checklist and focused group discussion guide. A total of 174 heads of households were interviewed. Statistical Package for Social Sciences (SPSS) was used to analyse the data and to calculate sustainability scores for water schemes. SPSS was also used to classify sustainability scores according to sustainability categories: sustainable, partially sustainable and non-sustainable. The averages of the ratings for the different sub-factors studied and the results on the sustainability scores for the sustainable, partially sustainable and non-sustainable schemes were then computed and compared to establish the main factors influencing sustainability of the water schemes. The results indicated technical and social factors as most critical while financial and institutional, although important, played a lesser role. Factors which contributed to the sustainability of water schemes were: functionality; design flow; water fetching time; ability to meet additional demand; use by population; equity; participation in decision making on operation and maintenance; existence of fund for operation and maintenance; willingness to contribute money; existence of a user’s committee; participation in the initial planning and design of the water scheme; and coordination between the local leaders and user’s committee. The main factors which made the schemes unsustainable were: long fetching time; non-involvement in decision making; lack of willingness to contribute funds; absence of users committee; and lack of cooperation between local leaders and the users committee. Water service providers should address the technical, social, financial and institutional factors identified affecting sustainability in their planning and implementation of rural water schemes.

Micrometeorological Measurement of Fetch- and Atmospheric Stability-Dependent Air- Water Exchange of Legacy Semivolatile Organic Contaminants in Lake Superior

NASA Astrophysics Data System (ADS)

Perlinger, J. A.; Tobias, D. E.; Rowe, M. D.

2008-12-01

Coastal waters including the Laurentian Great Lakes are particularly susceptible to local, regional, and long- range transport and deposition of semivolatile organic contaminants (SOCs) as gases and/or associated with particles. Recently-marketed SOCs can be expected to undergo net deposition in surface waters, whereas legacy SOCs such as polychlorinated biphenyls (PCBs) are likely to be at equilibrium with respect to air-water exchange, or, if atmospheric concentrations decrease through, e.g., policy implementation, to undergo net gas emission. SOC air-water exchange flux is usually estimated using the two-film model. This model describes molecular diffusion through the air and water films adjacent to the air-water interface. Air-water exchange flux is estimated as the product of SOC fugacity, typically based on on-shore gaseous concentration measurements, and a transfer coefficient, the latter which is estimated from SOC properties and environmental conditions. The transfer coefficient formulation commonly applied neglects resistance to exchange in the internal boundary layer under atmospherically stable conditions, and the use of on-shore gaseous concentration neglects fetch-dependent equilibration, both of which will tend to cause overestimation of flux magnitude. Thus, for legacy chemicals or in any highly contaminated surface water, the rate at which the water is cleansed through gas emission tends to be over-predicted using this approach. Micrometeorological measurement of air-water exchange rates of legacy SOCs was carried out on ships during four transect experiments during off-shore flow in Lake Superior using novel multicapillary collection devices and thermal extraction technology to measure parts-per-quadrillion SOC levels. Employing sensible heat in the modified Bowen ratio, fluxes at three over-water stations along the transects were measured, along with up-wind, onshore gaseous concentration and aqueous concentration. The atmosphere was unstable for one of the four trajectories and stable for the other three trajectories. Two of three transects carried out under stable conditions are complicated because, as revealed by back-trajectory analysis, different air masses were sampled at each station, and, for one of these transects, the air masses spent significant portions of time over land. Analyses of legacy pesticide concentrations carried out to date suggest that under stable and unstable conditions, fluxes were out of the lake. We present and compare micrometeorological measurements and two-film estimates of fluxes of legacy pesticides and PCBs.

Spatial Mapping of Agricultural Water Productivity Using the SWAT Model

NASA Astrophysics Data System (ADS)

Thokal, Rajesh Tulshiram; Gorantiwar, S. D.; Kothari, Mahesh; Bhakar, S. R.; Nandwana, B. P.

2015-03-01

The Sina river basin is facing both episodic and chronic water shortages due to intensive irrigation development. The main objective of this study was to characterize the hydrologic processes of the Sina river basin and assess crop water productivity using the distributed hydrologic model, SWAT. In the simulation year (1998-1999), the inflow to reservoir from upstream side was the major contributor to the reservoir accounting for 92 % of the total required water release for irrigation purpose (119.5 Mm3), while precipitation accounted for 4.1 Mm3. Annual release of water for irrigation was 119.5 Mm3 out of which 54 % water was diverted for irrigation purpose, 26 % was wasted as conveyance loss, average discharge at the command outlet was estimated as 4 % and annual average ground-water recharge coefficient was in the range of 13-17 %. Various scenarios involving water allocation rule were tested with the goal of increasing economic water productivity values in the Sina Irrigation Scheme. Out of those, only most benefited allocation rule is analyzed in this paper. Crop yield varied from 1.98 to 25.9 t/ha, with the majority of the area between 2.14 and 2.78 t/ha. Yield and WP declined significantly in loamy soils of the irrigation command. Crop productivity in the basin was found in the lower range when compared with potential and global values. The findings suggested that there was a potential to improve further. Spatial variations in yield and WP were found to be very high for the crops grown during rabi season, while those were low for the crops grown during kharif season. The crop yields and WP during kharif season were more in the lower reach of the irrigation commands, where loamy soil is more concentrated. Sorghum in both seasons was most profitable. Sorghum fetched net income fivefold that of sunflower, two and half fold of pearl millet and one and half fold of mung beans as far as crop during kharif season were concerned and it fetched fourfold that of groundnut, threefold of wheat, twofold of onion during rabi season and was sevenfold of sugarcane. Analysis suggests that maximization of the area by provision of supplemental irrigation to rainfed areas as well as better on-farm water management practices can provide opportunities for improving water productivity.

Proposed Hydrodynamic Model Increases the Ability of Land-Surface Models to Capture Intra-Daily Dynamics of Transpiration and Canopy Structure Effects

NASA Astrophysics Data System (ADS)

Matheny, A. M.; Bohrer, G.; Mirfenderesgi, G.; Schafer, K. V.; Ivanov, V. Y.

2014-12-01

Hydraulic limitations are known to control transpiration in forest ecosystems when the soil is drying or when the vapor pressure deficit between the air and stomata is very large, but they can also impact stomatal apertures under conditions of adequate soil moisture and lower evaporative demand. We use the NACP dataset of latent heat flux measurements and model observations for multiple sites and models to demonstrate models' difficulties in capturing intra-daily hysteresis. We hypothesize that this is a result of un-resolved afternoon stomata closure due to hydrodynamic stresses. The current formulations for stomatal conductance and the empirical coupling between stomatal conductance and soil moisture used by these models does not resolve the hydrodynamic process of water movement from the soil to the leaves. This approach does not take advantage of advances in our understanding of water flow and storage in the trees, or of tree and canopy structure. A more thorough representation of the tree-hydrodynamic processes could potentially remedy this significant source of model error. In a forest plot at the University of Michigan Biological Station, we use measurements of sap flux and leaf water potential to demonstrate that trees of similar type - late successional deciduous trees - have very different hydrodynamic strategies that lead to differences in their temporal patterns of stomatal conductance and thus hysteretic cycles of transpiration. These differences will lead to large differences in conductance and water use based on the species composition of the forest. We also demonstrate that the size and shape of the tree branching system leads to differences in extent of hydrodynamic stress, which may change the forest respiration patterns as the forest grows and ages. We propose a framework to resolve tree hydrodynamics in global and regional models based on the Finite-Elements Tree-Crown Hydrodynamics model (FETCH) -a hydrodynamic model that can resolve the fast dynamics of stomatal conductance. FETCH simulates water flow through a tree as a system of porous media conduits and calculates the amount of hydraulic limitation to stomatal conductance, given the atmospheric and biological variables from the global model, and could replace the current empirical formulation for stomatal adjustment based on soil moisture.

Evaluating The Reliability of Point Estimates of Wetland Evaporation

NASA Astrophysics Data System (ADS)

Gavin, H.; Agnew, C. T.

The Penman-Monteith formulation of evaporation has been criticised for its reliance upon point estimates raising concerns that areal estimates of wetland evaporation based upon single weather stations can be misleading. Typically wetlands are composed of a complex mosaic of land cover types each of which can produce different evaporative rates. The need to account for wetland patches when monitoring hydrological fluxes has been noted, while Morton (1983) has long argued for a fundamentally different approach to the calculation of regional evaporation. This paper presents the work carried out at wet grassland in Southern England that was monitored with several automatic weather stations (AWS) and a bowen ratio station to investigate microclimate variations. The significance of fetch was examined using the approach adopted by Gash (1986) based upon surface roughness to estimate the fraction of evaporation sensed from a specific distance upwind of the monitoring station. This theoretical analysis reveals that the fraction of evaporation contributed by the surrounding area steadily increases to a value of 77% at a distance of 224m and thereafter declines rapidly, under stable atmospheric conditions. Thus point climate observations may not reflect surface conditions at greater distances. This result was tested through the deployment offour AWS around the wetland. The data yielded a different response, suggesting that homogeneous conditions prevailed and the central AWS did provide reliable areal estimates of evaporation. The apparent contradiction is a result of not accounting for wind speeds found in wetlands that lead to widespread atmospheric mixing. These findings are typical of moist conditions whereas for example Guo and Scheupp (1994) found that a patchwork of dry fields and wet ditches, characteristic of the study site in summer, could produce differences of up to 50% in evaporation. The paper will also present the initial results of an investigation of the role of dry patches upon wetland evaporation estimates. Morton, F.I. 1983 Operational estimates of evapotranspiration and their significance to the science and practice of hydrology. Journal of Hydrology 66 1:76. Gash, J.H.C. 1986 A note on estimating the effect of limited fetch on micrometeorological evaporation measurements. Boundary Layer Meteorology 35: 409-413. Guo, Y. Schuepp, P.H. 1994a On surface energy balance over the northern wetlands 1. The effects of small-scale temperature and wetness heterogeneity. Journal of Geophysical Research 99 (D1) 1601-1612.

Flow tilt angles near forest edges - Part 2: Lidar anemometry

NASA Astrophysics Data System (ADS)

Dellwik, E.; Mann, J.; Bingöl, F.

2010-05-01

A novel way of estimating near-surface mean flow tilt angles from ground based Doppler lidar measurements is presented. The results are compared with traditional mast based in-situ sonic anemometry. The tilt angle assessed with the lidar is based on 10 or 30 min mean values of the velocity field from a conically scanning lidar. In this mode of measurement, the lidar beam is rotated in a circle by a prism with a fixed angle to the vertical at varying focus distances. By fitting a trigonometric function to the scans, the mean vertical velocity can be estimated. Lidar measurements from (1) a fetch-limited beech forest site taken at 48-175 m a.g.l. (above ground level), (2) a reference site in flat agricultural terrain and (3) a second reference site in complex terrain are presented. The method to derive flow tilt angles and mean vertical velocities from lidar has several advantages compared to sonic anemometry; there is no flow distortion caused by the instrument itself, there are no temperature effects and the instrument misalignment can be corrected for by assuming zero tilt angle at high altitudes. Contrary to mast-based instruments, the lidar measures the wind field with the exact same alignment error at a multitude of heights. Disadvantages with estimating vertical velocities from a lidar compared to mast-based measurements are potentially slightly increased levels of statistical errors due to limited sampling time, because the sampling is disjunct, and a requirement for homogeneous flow. The estimated mean vertical velocity is biased if the flow over the scanned circle is not homogeneous. It is demonstrated that the error on the mean vertical velocity due to flow inhomogeneity can be approximated by a function of the angle of the lidar beam to the vertical and the vertical gradient of the mean vertical velocity, whereas the error due to flow inhomogeneity on the horizontal mean wind speed is independent of the lidar beam angle. For the presented measurements over forest, it is evaluated that the systematic error due to the inhomogeneity of the flow is less than 0.2°. The results of the vertical conical scans were promising, and yielded positive flow angles for a sector where the forest is fetch-limited. However, more data and analysis are needed for a complete evaluation of the lidar technique.

An iterative procedure for obtaining maximum-likelihood estimates of the parameters for a mixture of normal distributions

NASA Technical Reports Server (NTRS)

Peters, B. C., Jr.; Walker, H. F.

1975-01-01

A general iterative procedure is given for determining the consistent maximum likelihood estimates of normal distributions. In addition, a local maximum of the log-likelihood function, Newtons's method, a method of scoring, and modifications of these procedures are discussed.

Effect of Water-Alcohol Injection and Maximum Economy Spark Advance on Knock-Limited Performance and Fuel Economy of a Large Air-Cooled Cylinder

NASA Technical Reports Server (NTRS)

Heinicke, Orville H.; Vandeman, Jack E.

1945-01-01

An investigation was conducted to determine the effect of a coolant solution of 25 percent ethyl alcohol, 25 percent methyl alcohol, and 50 percent water by volume and maximum-economy spark advance on knock-limited performance and fuel economy of a large air-cooled cylinder. The knock-limited performance of the cylinder at engine speeds of 2100 and 2500 rpm was determined for coolant-fuel ratios of 0.0, 0.2, and 0.4. The effect of water-alcohol injection on fuel economy was determined in constant charge-air flow tests. The tests were conducted at a spark advance of 20 deg B.T.C. and maximum-economy spark advance.

Universal adaptive torque control for PM motors for field-weakening region operation

DOEpatents

Royak, Semyon [Beachwood, OH; Harbaugh, Mark M [Richfield, OH; Breitzmann, Robert J [South Russel, OH; Nondahl, Thomas A [Wauwatosa, WI; Schmidt, Peter B [Franklin, WI; Liu, Jingbo [Milwaukee, WI

2011-03-29

The invention includes a motor controller and method for controlling a permanent magnet motor. In accordance with one aspect of the present technique, a permanent magnet motor is controlled by, among other things, receiving a torque command, determining a normalized torque command by normalizing the torque command to a characteristic current of the motor, determining a normalized maximum available voltage, determining an inductance ratio of the motor, and determining a direct-axis current based upon the normalized torque command, the normalized maximum available voltage, and the inductance ratio of the motor.

Determination of Strength Exercise Intensities Based on the Load-Power-Velocity Relationship

PubMed Central

Jandačka, Daniel; Beremlijski, Petr

2011-01-01

The velocity of movement and applied load affect the production of mechanical power output and subsequently the extent of the adaptation stimulus in strength exercises. We do not know of any known function describing the relationship of power and velocity and load in the bench press exercise. The objective of the study is to find a function modeling of the relationship of relative velocity, relative load and mechanical power output for the bench press exercise and to determine the intensity zones of the exercise for specifically focused strength training of soccer players. Fifteen highly trained soccer players at the start of a competition period were studied. The subjects of study performed bench presses with the load of 0, 10, 30, 50, 70 and 90% of the predetermined one repetition maximum with maximum possible speed of movement. The mean measured power and velocity for each load (kg) were used to develop a multiple linear regression function which describes the quadratic relationship between the ratio of power (W) to maximum power (W) and the ratios of the load (kg) to one repetition maximum (kg) and the velocity (m•s−1) to maximal velocity (m•s−1). The quadratic function of two variables that modeled the searched relationship explained 74% of measured values in the acceleration phase and 75% of measured values from the entire extent of the positive power movement in the lift. The optimal load for reaching maximum power output suitable for the dynamics effort strength training was 40% of one repetition maximum, while the optimal mean velocity would be 75% of maximal velocity. Moreover, four zones: maximum power, maximum velocity, velocity-power and strength-power were determined on the basis of the regression function. PMID:23486484

Determination of strength exercise intensities based on the load-power-velocity relationship.

PubMed

Jandačka, Daniel; Beremlijski, Petr

2011-06-01

The velocity of movement and applied load affect the production of mechanical power output and subsequently the extent of the adaptation stimulus in strength exercises. We do not know of any known function describing the relationship of power and velocity and load in the bench press exercise. The objective of the study is to find a function modeling of the relationship of relative velocity, relative load and mechanical power output for the bench press exercise and to determine the intensity zones of the exercise for specifically focused strength training of soccer players. Fifteen highly trained soccer players at the start of a competition period were studied. The subjects of study performed bench presses with the load of 0, 10, 30, 50, 70 and 90% of the predetermined one repetition maximum with maximum possible speed of movement. The mean measured power and velocity for each load (kg) were used to develop a multiple linear regression function which describes the quadratic relationship between the ratio of power (W) to maximum power (W) and the ratios of the load (kg) to one repetition maximum (kg) and the velocity (m•s(-1)) to maximal velocity (m•s(-1)). The quadratic function of two variables that modeled the searched relationship explained 74% of measured values in the acceleration phase and 75% of measured values from the entire extent of the positive power movement in the lift. The optimal load for reaching maximum power output suitable for the dynamics effort strength training was 40% of one repetition maximum, while the optimal mean velocity would be 75% of maximal velocity. Moreover, four zones: maximum power, maximum velocity, velocity-power and strength-power were determined on the basis of the regression function.

[Pitfalls in the prescription of reading glasses].

PubMed

Krause, H-K

2011-04-01

People in the second half of their lives often require reading glasses. A basic requirement for determining suitable reading glasses is measurement of the patient's accommodation, which describes the change in the eye's optical power caused by the attempt to clearly focus on an object at a certain distance. The maximum accommodation performance of a person already begins to decline from the age of 40 onwards. When it becomes increasingly difficult to adjust to the typical reading distance of 40 cm, one speaks of presbyopia: age-related farsightedness. This contribution describes two appropriate methods for determining the strength of reading glasses: determination of the maximum accommodation performance by measuring the near point distance and determination of the maximum accommodation effort by measuring the relative positive and negative accommodation. Optimal reading glasses enable the patient to focus sharply on something from the working distance that is closer but also on something that is further away.

30 CFR 36.44 - Maximum allowable fuel : air ratio.

Code of Federal Regulations, 2012 CFR

2012-07-01

... delivered to MSHA with the fuel-injection system adjusted by the applicant and tests of the exhaust-gas... adjustment of the fuel-injection system shall be accepted. The maximum fuel : air ratio determined from the... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Maximum allowable fuel : air ratio. 36.44...

30 CFR 36.44 - Maximum allowable fuel : air ratio.

Code of Federal Regulations, 2013 CFR

2013-07-01

... delivered to MSHA with the fuel-injection system adjusted by the applicant and tests of the exhaust-gas... adjustment of the fuel-injection system shall be accepted. The maximum fuel : air ratio determined from the... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Maximum allowable fuel : air ratio. 36.44...

30 CFR 36.44 - Maximum allowable fuel : air ratio.

Code of Federal Regulations, 2010 CFR

2010-07-01

... delivered to MSHA with the fuel-injection system adjusted by the applicant and tests of the exhaust-gas... adjustment of the fuel-injection system shall be accepted. The maximum fuel : air ratio determined from the... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maximum allowable fuel : air ratio. 36.44...

30 CFR 36.44 - Maximum allowable fuel:air ratio.

Code of Federal Regulations, 2014 CFR

2014-07-01

... delivered to MSHA with the fuel-injection system adjusted by the applicant and tests of the exhaust-gas... adjustment of the fuel-injection system shall be accepted. The maximum fuel:air ratio determined from the... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Maximum allowable fuel:air ratio. 36.44 Section...

30 CFR 36.44 - Maximum allowable fuel : air ratio.

Code of Federal Regulations, 2011 CFR

2011-07-01

... delivered to MSHA with the fuel-injection system adjusted by the applicant and tests of the exhaust-gas... adjustment of the fuel-injection system shall be accepted. The maximum fuel : air ratio determined from the... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Maximum allowable fuel : air ratio. 36.44...

Adverse Climatic Conditions and Impact on Construction Scheduling and Cost

DTIC Science & Technology

1988-01-01

ABBREVIATIONS ABS MAX MAX TEMP ...... Absolute maximum maximum temperature ABS MIN MIN TEMP ...... Absolute minimum minimum temperature BTU...o Degrees Farenheit MEAN MAX TEMP o.................... Mean maximum temperature MEAN MIN TEMP...temperatures available, a determination had to be made as to whether forecasts were based on absolute , mean, or statistically derived temperatures

30 CFR 57.19061 - Maximum hoisting speeds.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Maximum hoisting speeds. 57.19061 Section 57... Hoisting Hoisting Procedures § 57.19061 Maximum hoisting speeds. The safe speed for hoisting persons shall be determined for each shaft, and this speed shall not be exceeded. Persons shall not be hoisted at a...

30 CFR 56.19061 - Maximum hoisting speeds.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maximum hoisting speeds. 56.19061 Section 56... Hoisting Procedures § 56.19061 Maximum hoisting speeds. The safe speed for hoisting persons shall be determined for each shaft, and this speed shall not be exceeded. Persons should not be hoisted at a speed...

30 CFR 57.19061 - Maximum hoisting speeds.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Maximum hoisting speeds. 57.19061 Section 57... Hoisting Hoisting Procedures § 57.19061 Maximum hoisting speeds. The safe speed for hoisting persons shall be determined for each shaft, and this speed shall not be exceeded. Persons shall not be hoisted at a...

30 CFR 56.19061 - Maximum hoisting speeds.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Maximum hoisting speeds. 56.19061 Section 56... Hoisting Procedures § 56.19061 Maximum hoisting speeds. The safe speed for hoisting persons shall be determined for each shaft, and this speed shall not be exceeded. Persons should not be hoisted at a speed...

Analysis and Evaluation of Parameters Determining Maximum Efficiency of Fish Protection

NASA Astrophysics Data System (ADS)

Khetsuriani, E. D.; Kostyukov, V. P.; Khetsuriani, T. E.

2017-11-01

The article is concerned with experimental research findings. The efficiency of fish fry protection from entering water inlets is the main criterion of any fish protection facility or device. The research was aimed to determine an adequate mathematical model E = f(PCT, Vp, α), where PCT, Vp and α are controlled factors influencing the process of fish fry protection. The result of the processing of experimental data was an adequate regression model. We determined the maximum of fish protection Emax=94,21 and the minimum of optimization function Emin=44,41. As a result of the statistical processing of experimental data we obtained adequate dependences for determining an optimal rotational speed of tip and fish protection efficiency. The analysis of fish protection efficiency dependence E% = f(PCT, Vp, α) allowed the authors to recommend the following optimized operating modes for it: the maximum fish protection efficiency is achieved at the process pressure PCT=3 atm, stream velocity Vp=0,42 m/s and nozzle inclination angle α=47°49’. The stream velocity Vp has the most critical influence on fish protection efficiency. The maximum efficiency of fish protection is obtained at the tip rotational speed of 70.92 rpm.

Determination of the Maximum Control Forces and Attainable Quickness in the Operation of Airplane Controls

NASA Technical Reports Server (NTRS)

Hertel, Heinrich

1930-01-01

This report is intended to furnish bases for load assumptions in the designing of airplane controls. The maximum control forces and quickness of operation are determined. The maximum forces for a strong pilot with normal arrangement of the controls is taken as 1.25 times the mean value obtained from tests with twelve persons. Tests with a number of persons were expected to show the maximum forces that a man of average strength can exert on the control stick in operating the elevator and ailerons and also on the rudder bar. The effect of fatigue, of duration and of the nature (static or dynamic) of the force, as also the condition of the test subject (with or without belt) were also considered.

Method for distance determination using range-gated imaging suitable for an arbitrary pulse shape

NASA Astrophysics Data System (ADS)

Kabashnikov, Vitaly; Kuntsevich, Boris

2017-10-01

A method for distance determination with the help of range-gated viewing systems suitable for the arbitrary shape of the illumination pulse is proposed. The method is based on finding the delay time at which maximum of the return pulse energy takes place. The maximum position depends on the pulse and gate durations and, generally speaking, on the pulse shape. If the pulse length is less than or equal to the gate duration, the delay time appropriate to the maximum does not depend on the pulse shape. At equal pulse and gate durations, there is a strict local maximum, which turns into a plateau when pulse is shorter than gate duration. A delay time appropriate to the strict local maximum or the far boundary of the plateau (where non-strict maximum is) is directly related to the distance to the object. These findings are confirmed by analytical relationships for trapezoid pulses and numerical results for the real pulse shape. To verify the proposed method we used a vertical wall located at different distances from 15 to 120m as an observed object. Delay time was changing discretely in increments of 5 ns. Maximum of the signal was determined by visual observation of the object on the monitor screen. The distance defined by the proposed method coincided with the direct measurement with accuracy 1- 2m, which is comparable with the delay time step multiplied by half of the light velocity. The results can be useful in the development of 3-D vision systems.

Step Test: a method for evaluating maximum oxygen consumption to determine the ability kind of work among students of medical emergencies

PubMed Central

Heydari, Payam; Varmazyar, Sakineh; Nikpey, Ahmad; Variani, Ali Safari; Jafarvand, Mojtaba

2017-01-01

Introduction Maximum oxygen consumption shows the maximum oxygen rate of muscle oxygenation that is acceptable in many cases, to measure the fitness between person and the desired job. Given that medical emergencies are important, and difficult jobs in emergency situations require people with high physical ability and readiness for the job, the aim of this study was to evaluate the maximum oxygen consumption, to determine the ability of work type among students of medical emergencies in Qazvin in 2016. Methods This study was a descriptive – analytical, and in cross-sectional type conducted among 36 volunteer students of medical emergencies in Qazvin in 2016. After necessary coordination for the implementation of the study, participants completed health questionnaires and demographic characteristics and then the participants were evaluated with step tests of American College of Sport Medicine (ACSM). Data analysis was done by SPSS version 18 and U-Mann-Whitney tests, Kruskal-Wallis and Pearson correlation coefficient. Results Average of maximum oxygen consumption of the participants was estimated 3.15±0.50 liters per minute. 91.7% of medical emergencies students were selected as appropriate in terms of maximum oxygen consumption and thus had the ability to do heavy and too heavy work. Average of maximum oxygen consumption evaluated by the U-Mann-Whitney test and Kruskal-Wallis, had significant relationship with age (p<0.05) and weight groups (p<0.001). There was a significant positive correlation between maximum oxygen consumption with weight and body mass index (p<0.001). Conclusion The results of this study showed that demographic variables of weight and body mass index are the factors influencing the determination of maximum oxygen consumption, as most of the students had the ability to do heavy, and too heavy work. Therefore, people with ability to do average work are not suitable for medical emergency tasks. PMID:28461880

Step Test: a method for evaluating maximum oxygen consumption to determine the ability kind of work among students of medical emergencies.

PubMed

Heydari, Payam; Varmazyar, Sakineh; Nikpey, Ahmad; Variani, Ali Safari; Jafarvand, Mojtaba

2017-03-01

Maximum oxygen consumption shows the maximum oxygen rate of muscle oxygenation that is acceptable in many cases, to measure the fitness between person and the desired job. Given that medical emergencies are important, and difficult jobs in emergency situations require people with high physical ability and readiness for the job, the aim of this study was to evaluate the maximum oxygen consumption, to determine the ability of work type among students of medical emergencies in Qazvin in 2016. This study was a descriptive - analytical, and in cross-sectional type conducted among 36 volunteer students of medical emergencies in Qazvin in 2016. After necessary coordination for the implementation of the study, participants completed health questionnaires and demographic characteristics and then the participants were evaluated with step tests of American College of Sport Medicine (ACSM). Data analysis was done by SPSS version 18 and U-Mann-Whitney tests, Kruskal-Wallis and Pearson correlation coefficient. Average of maximum oxygen consumption of the participants was estimated 3.15±0.50 liters per minute. 91.7% of medical emergencies students were selected as appropriate in terms of maximum oxygen consumption and thus had the ability to do heavy and too heavy work. Average of maximum oxygen consumption evaluated by the U-Mann-Whitney test and Kruskal-Wallis, had significant relationship with age (p<0.05) and weight groups (p<0.001). There was a significant positive correlation between maximum oxygen consumption with weight and body mass index (p<0.001). The results of this study showed that demographic variables of weight and body mass index are the factors influencing the determination of maximum oxygen consumption, as most of the students had the ability to do heavy, and too heavy work. Therefore, people with ability to do average work are not suitable for medical emergency tasks.

Determination of the maximum-depth to potential field sources by a maximum structural index method

NASA Astrophysics Data System (ADS)

Fedi, M.; Florio, G.

2013-01-01

A simple and fast determination of the limiting depth to the sources may represent a significant help to the data interpretation. To this end we explore the possibility of determining those source parameters shared by all the classes of models fitting the data. One approach is to determine the maximum depth-to-source compatible with the measured data, by using for example the well-known Bott-Smith rules. These rules involve only the knowledge of the field and its horizontal gradient maxima, and are independent from the density contrast. Thanks to the direct relationship between structural index and depth to sources we work out a simple and fast strategy to obtain the maximum depth by using the semi-automated methods, such as Euler deconvolution or depth-from-extreme-points method (DEXP). The proposed method consists in estimating the maximum depth as the one obtained for the highest allowable value of the structural index (Nmax). Nmax may be easily determined, since it depends only on the dimensionality of the problem (2D/3D) and on the nature of the analyzed field (e.g., gravity field or magnetic field). We tested our approach on synthetic models against the results obtained by the classical Bott-Smith formulas and the results are in fact very similar, confirming the validity of this method. However, while Bott-Smith formulas are restricted to the gravity field only, our method is applicable also to the magnetic field and to any derivative of the gravity and magnetic field. Our method yields a useful criterion to assess the source model based on the (∂f/∂x)max/fmax ratio. The usefulness of the method in real cases is demonstrated for a salt wall in the Mississippi basin, where the estimation of the maximum depth agrees with the seismic information.

Emotions and voluntary action: what link in children with autism?

PubMed

Vernazza-Martin, S; Longuet, S; Chamot, J M; Orève, M J

2013-08-15

This research focuses on the impact of emotions--defined as "motivational states"--on the organization of goal directed locomotion in children with autism. Walking toward a goal involves both cognitive processes responsible for movement planning and automatic processes linked to movement programming. To these processes, motivation leading to achieving the goal is added. For some authors, a deficit of planning and/or programming processes is highlighted in autism. Others stand for some impairment of the emotional system. The aim of this research is to link these two viewpoints and to determine if, in children with autism, the organization of locomotion is affected by a positive/aversive emotion conferred to an object to fetch. Twenty-nine children participated in the study (11 children with autism--mean age 122 months; 9 mental age-matched controls--mean age 36 months; and 9 chronological age-matched controls--mean age 122 months). They were instructed to go and get a positive or aversive emotional valence object located straight ahead, at 30° to the right or straight ahead then moved at mid-distance to the right. Gait analysis was performed using the Vicon system. The main results suggest that a positive emotional context promotes the cognitive processes involved in movement planning while an aversive emotional context blocks it or disturbs it in children with autism. No emotions effect is observed on movement programming. It is suggested that emotions triggered off and modulated movement planning and that the deficit observed was related to a developmental impairment rather than to a developmental delay. Copyright © 2013 Elsevier B.V. All rights reserved.

Climatic factors directly impact the volatile organic compound fingerprint in green Arabica coffee bean as well as coffee beverage quality.

PubMed

Bertrand, B; Boulanger, R; Dussert, S; Ribeyre, F; Berthiot, L; Descroix, F; Joët, T

2012-12-15

Coffee grown at high elevations fetches a better price than that grown in lowland regions. This study was aimed at determining whether climatic conditions during bean development affected sensory perception of the coffee beverage and combinations of volatile compounds in green coffee. Green coffee samples from 16 plots representative of the broad range of climatic variations in Réunion Island were compared by sensory analysis. Volatiles were extracted by solid phase micro-extraction and the volatile compounds were analysed by GC-MS. The results revealed that, among the climatic factors, the mean air temperature during seed development greatly influenced the sensory profile. Positive quality attributes such as acidity, fruity character and flavour quality were correlated and typical of coffees produced at cool climates. Two volatile compounds (ethanal and acetone) were identified as indicators of these cool temperatures. Among detected volatiles, most of the alcohols, aldehydes, hydrocarbons and ketones appeared to be positively linked to elevated temperatures and high solar radiation, while the sensory profiles displayed major defects (i.e. green, earthy flavour). Two alcohols (butan-1,3-diol and butan-2,3-diol) were closely correlated with a reduction in aromatic quality, acidity and an increase in earthy and green flavours. We assumed that high temperatures induce accumulation of these compounds in green coffee, and would be detected as off-flavours, even after roasting. Climate change, which generally involves a substantial increase in average temperatures in mountainous tropical regions, could be expected to have a negative impact on coffee quality. Copyright © 2012 Elsevier Ltd. All rights reserved.

A Global User-Driven Model for Tile Prefetching in Web Geographical Information Systems

PubMed Central

Pan, Shaoming; Chong, Yanwen; Zhang, Hang; Tan, Xicheng

2017-01-01

A web geographical information system is a typical service-intensive application. Tile prefetching and cache replacement can improve cache hit ratios by proactively fetching tiles from storage and replacing the appropriate tiles from the high-speed cache buffer without waiting for a client’s requests, which reduces disk latency and improves system access performance. Most popular prefetching strategies consider only the relative tile popularities to predict which tile should be prefetched or consider only a single individual user's access behavior to determine which neighbor tiles need to be prefetched. Some studies show that comprehensively considering all users’ access behaviors and all tiles’ relationships in the prediction process can achieve more significant improvements. Thus, this work proposes a new global user-driven model for tile prefetching and cache replacement. First, based on all users’ access behaviors, a type of expression method for tile correlation is designed and implemented. Then, a conditional prefetching probability can be computed based on the proposed correlation expression mode. Thus, some tiles to be prefetched can be found by computing and comparing the conditional prefetching probability from the uncached tiles set and, similarly, some replacement tiles can be found in the cache buffer according to multi-step prefetching. Finally, some experiments are provided comparing the proposed model with other global user-driven models, other single user-driven models, and other client-side prefetching strategies. The results show that the proposed model can achieve a prefetching hit rate in approximately 10.6% ~ 110.5% higher than the compared methods. PMID:28085937

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ranson, W.F.; Schaeffel, J.A.; Murphree, E.A.

The response of prestressed and preheated plates subject to an exponentially decaying blast load was experimentally determined. A grid was reflected from the front surface of the plate and the response was recorded with a high speed camera. The camera used in this analysis was a rotating drum camera operating at 20,000 frames per second with a maximum of 224 frames at 39 microseconds separation. Inplane tension loads were applied to the plate by means of air cylinders. Maximum biaxial load applied to the plate was 500 pounds. Plate preheating was obtained with resistance heaters located in the specimen platemore » holder with a maximum capability of 500F. Data analysis was restricted to the maximum conditions at the center of the plate. Strains were determined from the photographic data and the stresses were calculated from the strain data. Results were obtained from zero preload conditions to a maximum of 480 pounds inplane tension loads and a plate temperature of 490F. The blast load ranged from 6 to 23 psi.« less

Comparison of three systems of solar water heating by thermosiphon

NASA Astrophysics Data System (ADS)

Hernández, E.; Guzmán, R. E.

2016-02-01

The main purpose of this project was to elaborate a comparison between three water heating systems; using two plane water heating solar collector and another using a vacuum tube heater, all of them are on top of the cafeteria's roof on building of the “Universidad Pontificia Bolivariana” in Bucaramanga, Colombia. Through testing was determined each type of water heating systems' performance, where the Stainless Steel tube collector reached a maximum efficiency of 71.58%, the Copper Tubing Collector a maximum value of 76.31% and for the Vacuum Tube Heater Collector a maximum efficiency of 72.33%. The collector with copper coil was the system more efficient. So, taking into account the Performance and Temperature Curves, along with the weather conditions at the time of the testing we determined that the most efficient Solar Heating System is the one using a Vacuum Tube Heater Collector. Reaching a maximum efficiency of 72.33% and a maximum temperature of 62.6°C.

14 CFR 23.1563 - Airspeed placards.

Code of Federal Regulations, 2011 CFR

2011-01-01

... multiengine-powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes, the maximum value of the minimum control speed, VMC (one-engine-inoperative) determined under § 23.149...

14 CFR 23.1563 - Airspeed placards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... multiengine-powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes, the maximum value of the minimum control speed, VMC (one-engine-inoperative) determined under § 23.149...

Evaluation of Bite Force After Open Reduction and Internal Fixation Using Microplates

PubMed Central

Kumar, S Tharani; Saraf, Saurabh; Devi, S Prasanna

2013-01-01

The primary aim of this study is to determine maximum bite force in molar and incisor regions of healthy individuals, to evaluate the bite force after open reduction and internal fixation of mandibular fractures using micro plates, for a period of up to 6 weeks and to determine the rate of recovery of maximum bite force in an Indian population. PMID:24910656

47 CFR 90.545 - TV/DTV interference protection criteria.

Code of Federal Regulations, 2011 CFR

2011-10-01

... contour (41 dBµV/m) (88.5 kilometers or 55.0 miles) of the DTV station. (b) Maximum ERP and HAAT. The maximum effective radiated power (ERP) and the antenna height above average terrain (HAAT) of the proposed... determined using the methods described in this section. (1) Each base station is limited to a maximum ERP of...

Effects of spatial and temporal variability of turbidity on phytoplankton blooms

USGS Publications Warehouse

May, Christine L.; Koseff, Jeffrey R.; Lucas, Lisa; Cloern, James E.; Schoellhamer, David H.

2003-01-01

A central challenge of coastal ecology is sorting out the interacting spatial and temporal components of environmental variability that combine to drive changes in phytoplankton biomass. For 2 decades, we have combined sustained observation and experimentation in South San Francisco Bay (SSFB) with numerical modeling analyses to search for general principles that define phytoplankton population responses to physical dynamics characteristic of shallow, nutrient-rich coastal waters having complex bathymetry and influenced by tides, wind and river flow. This study is the latest contribution where we investigate light-limited phytoplankton growth using a numerical model, by modeling turbidity as a function of suspended sediment concentrations (SSC). The goal was to explore the sensitivity of estuarine phytoplankton dynamics to spatial and temporal variations in turbidity, and to synthesize outcomes of simulation experiments into a new conceptual framework for defining the combinations of physical-biological forcings that promote or preclude development of phytoplankton blooms in coastal ecosystems. The 3 main conclusions of this study are: (1) The timing of the wind with semidiurnal tides and the spring-neap cycle can significantly enhance spring-neap variability in turbidity and phytoplankton biomass; (2) Fetch is a significant factor potentially affecting phytoplankton dynamics by enhancing and/or creating spatial variability in turbidity; and (3) It is possible to parameterize the combined effect of the processes influencing turbidity‹and thus affecting potential phytoplankton bloom development‹with 2 indices for vertical and horizontal clearing of the water column. Our conceptual framework is built around these 2 indices, providing a means to determine under what conditions a phytoplankton bloom can occur, and whether a potential bloom is only locally supported or system-wide in scale. This conceptual framework provides a tool for exploring the inherent light climate attributes of shallow estuarine ecosystems and helps determine susceptibility to the harmful effects of nutrient enrichment.

Parametric Grid Information in the DOE Knowledge Base: Data Preparation, Storage, and Access

DOE Office of Scientific and Technical Information (OSTI.GOV)

HIPP,JAMES R.; MOORE,SUSAN G.; MYERS,STEPHEN C.

The parametric grid capability of the Knowledge Base provides an efficient, robust way to store and access interpolatable information which is needed to monitor the Comprehensive Nuclear Test Ban Treaty. To meet both the accuracy and performance requirements of operational monitoring systems, we use a new approach which combines the error estimation of kriging with the speed and robustness of Natural Neighbor Interpolation (NNI). The method involves three basic steps: data preparation (DP), data storage (DS), and data access (DA). The goal of data preparation is to process a set of raw data points to produce a sufficient basis formore » accurate NNI of value and error estimates in the Data Access step. This basis includes a set of nodes and their connectedness, collectively known as a tessellation, and the corresponding values and errors that map to each node, which we call surfaces. In many cases, the raw data point distribution is not sufficiently dense to guarantee accurate error estimates from the NNI, so the original data set must be densified using a newly developed interpolation technique known as Modified Bayesian Kriging. Once appropriate kriging parameters have been determined by variogram analysis, the optimum basis for NNI is determined in a process they call mesh refinement, which involves iterative kriging, new node insertion, and Delauny triangle smoothing. The process terminates when an NNI basis has been calculated which will fir the kriged values within a specified tolerance. In the data storage step, the tessellations and surfaces are stored in the Knowledge Base, currently in a binary flatfile format but perhaps in the future in a spatially-indexed database. Finally, in the data access step, a client application makes a request for an interpolated value, which triggers a data fetch from the Knowledge Base through the libKBI interface, a walking triangle search for the containing triangle, and finally the NNI interpolation.« less

Psychophysical basis for maximum pushing and pulling forces: A review and recommendations.

PubMed

Garg, Arun; Waters, Thomas; Kapellusch, Jay; Karwowski, Waldemar

2014-03-01

The objective of this paper was to perform a comprehensive review of psychophysically determined maximum acceptable pushing and pulling forces. Factors affecting pushing and pulling forces are identified and discussed. Recent studies show a significant decrease (compared to previous studies) in maximum acceptable forces for males but not for females when pushing and pulling on a treadmill. A comparison of pushing and pulling forces measured using a high inertia cart with those measured on a treadmill shows that the pushing and pulling forces using high inertia cart are higher for males but are about the same for females. It is concluded that the recommendations of Snook and Ciriello (1991) for pushing and pulling forces are still valid and provide reasonable recommendations for ergonomics practitioners. Regression equations as a function of handle height, frequency of exertion and pushing/pulling distance are provided to estimate maximum initial and sustained forces for pushing and pulling acceptable to 75% male and female workers. At present it is not clear whether pushing or pulling should be favored. Similarly, it is not clear what handle heights would be optimal for pushing and pulling. Epidemiological studies are needed to determine relationships between psychophysically determined maximum acceptable pushing and pulling forces and risk of musculoskeletal injuries, in particular to low back and shoulders.

Psychophysical basis for maximum pushing and pulling forces: A review and recommendations

PubMed Central

Garg, Arun; Waters, Thomas; Kapellusch, Jay; Karwowski, Waldemar

2015-01-01

The objective of this paper was to perform a comprehensive review of psychophysically determined maximum acceptable pushing and pulling forces. Factors affecting pushing and pulling forces are identified and discussed. Recent studies show a significant decrease (compared to previous studies) in maximum acceptable forces for males but not for females when pushing and pulling on a treadmill. A comparison of pushing and pulling forces measured using a high inertia cart with those measured on a treadmill shows that the pushing and pulling forces using high inertia cart are higher for males but are about the same for females. It is concluded that the recommendations of Snook and Ciriello (1991) for pushing and pulling forces are still valid and provide reasonable recommendations for ergonomics practitioners. Regression equations as a function of handle height, frequency of exertion and pushing/pulling distance are provided to estimate maximum initial and sustained forces for pushing and pulling acceptable to 75% male and female workers. At present it is not clear whether pushing or pulling should be favored. Similarly, it is not clear what handle heights would be optimal for pushing and pulling. Epidemiological studies are needed to determine relationships between psychophysically determined maximum acceptable pushing and pulling forces and risk of musculoskeletal injuries, in particular to low back and shoulders. PMID:26664045

Preliminary studies of the effect of thinning techniques over muon production profiles

NASA Astrophysics Data System (ADS)

Tomishiyo, G.; Souza, V.

2017-06-01

In the context of air shower simulations, thinning techniques are employed to reduce computational time and storage requirements. These techniques are tailored to preserve locally mean quantities during shower development, such as the average number of particles in a given atmosphere layer, and to not induce systematic shifts in shower observables, such as the depth of shower maximum. In this work we investigate thinning effects on the determination of the depth in which the shower has the maximum muon production {X}\\max μ -{sim}. We show preliminary results in which the thinning factor and maximum thinning weight might influence the determination of {X}\\max μ -{sim}

Tectonics on Iapetus: Despinning, respinning, or something completely different?

NASA Astrophysics Data System (ADS)

Singer, Kelsi N.; McKinnon, William B.

2011-11-01

Saturn's moon Iapetus is unique in that it has apparently despun while retaining a substantial equatorial bulge. Stresses arising from such a non-hydrostatic shape should in principle cause surface deformation (tectonics). As part of a search for such a tectonic signature, lineaments (linear surface features) on Iapetus were mapped on both its bright and dark hemispheres. Lineament orientations were then compared to model stress patterns predicted for spin-down from a rotation period of 16.5 h (or less) to its present synchronous period, and for a range of lithospheric thicknesses. Many lineaments are straight segments of crater rimwalls, which may be faults or joints reactivated during complex crater collapse. Most striking are several large troughs on the bright, trailing hemisphere. These troughs appear to be extensional and are distinctive on that hemisphere, because the interior floors and walls of the troughs contain dark material. Globally, no specific evidence of strike slip or thrust offsets are seen, but this could be due to the age and degraded nature of any such features. We find that observed lineament orientations do not correlate with predicted patterns due to despinning on either hemisphere (the equatorial ridge was specifically excluded from this analysis, and is considered separately). Modest evidence for preferred orientations ±40° from north could be construed as consistent with respinning, which is not necessarily far-fetched. Assuming the rigidity of unfractured ice, predicted maximum lithospheric differential stresses from despinning range from ˜1 MPa to ˜160 MPa for the elastic spheroid and thin lithosphere limits, respectively (although it is only for thicker elastic lithospheres that we expect a nonhydrostatic state to be maintained over geologic time against lithospheric failure). The tectonic signature of despinning may have been obscured over time because the surface of Iapetus is very ancient, Iapetus' thick lithosphere may have inhibited the full tectonic expression of despinning, or both. Several prominent lineaments strike E-W, and are thus parallel to the equatorial ridge (though not physically close to it), but a tectonic or volcanic origin for the ridge is highly problematic.

The Type-2 Fuzzy Logic Controller-Based Maximum Power Point Tracking Algorithm and the Quadratic Boost Converter for Pv System

NASA Astrophysics Data System (ADS)

Altin, Necmi

2018-05-01

An interval type-2 fuzzy logic controller-based maximum power point tracking algorithm and direct current-direct current (DC-DC) converter topology are proposed for photovoltaic (PV) systems. The proposed maximum power point tracking algorithm is designed based on an interval type-2 fuzzy logic controller that has an ability to handle uncertainties. The change in PV power and the change in PV voltage are determined as inputs of the proposed controller, while the change in duty cycle is determined as the output of the controller. Seven interval type-2 fuzzy sets are determined and used as membership functions for input and output variables. The quadratic boost converter provides high voltage step-up ability without any reduction in performance and stability of the system. The performance of the proposed system is validated through MATLAB/Simulink simulations. It is seen that the proposed system provides high maximum power point tracking speed and accuracy even for fast changing atmospheric conditions and high voltage step-up requirements.

Demagnetization using a determined estimated magnetic state

DOEpatents

Denis, Ronald J; Makowski, Nathanael J

2015-01-13

A method for demagnetizing comprising positioning a core within the electromagnetic field generated by a first winding until the generated first electrical current is not substantially increasing, thereby determining a saturation current. A second voltage, having the opposite polarity, is then applied across the first winding until the generated second electrical current is approximately equal to the magnitude of the determined saturation current. The maximum magnetic flux within the core is then determined using the voltage across said first winding and the second current. A third voltage, having the opposite polarity, is then applied across the first winding until the core has a magnetic flux equal to approximately half of the determined maximum magnetic flux within the core.

Optimization of reading conditions for flat panel displays.

PubMed

Thomas, J A; Chakrabarti, K; Kaczmarek, R V; Maslennikov, A; Mitchell, C A; Romanyukha, A

2006-06-01

Task Group 18 (TG 18) of the American Association of Physicists in Medicine has developed guidelines for Assessment of Display Performance for Medical Imaging Systems. In this document, a method for determination of the maximum room lighting for displays is suggested. It is based on luminance measurements of a black target displayed on each display device at different room illuminance levels. Linear extrapolation of the above luminance measurements vs. room illuminance allows one to determine diffuse and specular reflection coefficients. TG 18 guidelines have established recommended maximum room lighting. It is based on the characterization of the display by its minimum and maximum luminance and the description of room by diffuse and specular coefficients. We carried out these luminance measurements for three selected displays to determine their optimum viewing conditions: one cathode ray tube and two flat panels. We found some problems with the application of the TG 18 guidelines to optimize viewing conditions for IBM T221 flat panels. Introduction of the requirement for minimum room illuminance allows a more accurate determination of the optimal viewing conditions (maximum and minimum room illuminance) for IBM flat panels. It also addresses the possible loss of contrast in medical images on flat panel displays because of the effect of nonlinearity in the dependence of luminance on room illuminance at low room lighting.

The numerical evaluation of maximum-likelihood estimates of the parameters for a mixture of normal distributions from partially identified samples

NASA Technical Reports Server (NTRS)

Walker, H. F.

1976-01-01

Likelihood equations determined by the two types of samples which are necessary conditions for a maximum-likelihood estimate were considered. These equations suggest certain successive approximations iterative procedures for obtaining maximum likelihood estimates. The procedures, which are generalized steepest ascent (deflected gradient) procedures, contain those of Hosmer as a special case.

Effects of pH and temperature on growth and glycerol production kinetics of two indigenous wine strains of Saccharomyces cerevisiae from Turkey

PubMed Central

Yalcin, Seda Karasu; Yesim Ozbas, Z.

2008-01-01

The study was performed in a batch system in order to determine the effects of pH and temperature on growth and glycerol production kinetics of two indigenous wine yeast strains Saccharomyces cerevisiae Kalecik 1 and Narince 3. The highest values of dry mass and specific growth rate were obtained at pH 4.00 for both of the strains. Maximum specific glycerol production rates were obtained at pH 5.92 and 6.27 for the strains Kalecik 1 and Narince 3, respectively. Kalecik 1 strain produced maximum 8.8 gL−1 of glycerol at pH 6.46. Maximum glycerol concentration obtained by the strain Narince 3 was 9.1 gL−1 at pH 6.48. Both yeasts reached maximum specific growth rate at 30°C. Optimum temperature range for glycerol production was determined as 25-30°C for the strain Kalecik 1. The strain Narince 3 reached maximum specific glycerol production rate at 30°C. Maximum glycerol concentrations at 30°C were obtained as 8.5 and 7.6 gL−1 for Kalecik 1 and Narince 3, respectively. PMID:24031225

Design and optimization of a self-deploying PV tent array

NASA Astrophysics Data System (ADS)

Colozza, Anthony J.

A study was performed to design a self-deploying tent shaped PV (photovoltaic) array and optimize the design for maximum specific power. Each structural component of the design was analyzed to determine the size necessary to withstand the various forces it would be subjected to. Through this analysis the component weights were determined. An optimization was performed to determine the array dimensions and blanket geometry which produce the maximum specific power for a given PV blanket. This optimization was performed for both Lunar and Martian environmental conditions. The performance specifications for the array at both locations and with various PV blankets were determined.

Eddy covariance measurement of CO2 flux to the atmosphere from a area of high volcanogenic emissions, Mammoth Mountain, California

USGS Publications Warehouse

Anderson, D.E.; Farrar, C.D.

2001-01-01

Three pilot studies were performed to assess application of the eddy covariance micrometeorological method in the measurement of carbon dioxide (CO2) flux of volcanic origin. The selected study area is one of high diffuse CO2 emission on Mammoth Mountain, CA. Because terrain and source characteristics make this a complex setting for this type of measurement, added consideration was given to source area and upwind fetch. Footprint analysis suggests that the eddy covariance measurements were representative of an upwind elliptical source area (3.8 ?? 103 m2) which can vary with mean wind direction, surface roughness, and atmospheric stability. CO2 flux averaged 8-16 mg m-2 s-1 (0.7-1.4 kg m-2 day-1). Eddy covariance measurements of flux were compared with surface chamber measurements made in separate studies [Geophys. Res. Lett. 25 (1998a) 1947; EOS Trans. 79 (1998) F941.] and were found to be similar. ?? 2001 Elsevier Science B.V. All rights reserved.

Status of vulnerable Cystoseira populations along the Italian infralittoral fringe, and relationships with environmental and anthropogenic variables.

PubMed

Mancuso, F P; Strain, E M A; Piccioni, E; De Clerck, O; Sarà, G; Airoldi, L

2018-04-01

We analyzed the occurrence and status of infralittoral fringe populations of Cystoseira spp. (Fucales) at thirteen rocky sites around the Italian coastline, and explored the relationships with relevant environmental and anthropogenic variables. We found Cystoseira populations at 11 sites: most were scattered and comprised monospecific stands of C. compressa, and only 6 sites also supported sparse specimens of either C. amentacea var. stricta or C. brachycarpa. Coastal human population density, Chlorophyll a seawater concentrations, sea surface temperature, annual range of sea surface temperature and wave fetch explained most of the variation of the status of C. compressa. We hypothesize a generally unhealthy state of the Italian Cystoseira infralittoral fringe populations and identify multiple co-occurring anthropogenic stressors as the likely drivers of these poor conditions. Extensive baseline monitoring is needed to describe how Cystoseira populations are changing, and implement a management framework for the conservation of these valuable but vulnerable habitats. Copyright © 2017 Elsevier Ltd. All rights reserved.

Reflected GPS Power for the Detection of Surface Roughness Patterns in Coastal Water

NASA Technical Reports Server (NTRS)

Oertel, George, F.; Allen, Thomas R.

2000-01-01

Coastal bays formed by the barrier islands of Delaware, Maryland and Virginia are parts of a coastal region known as a "Coastal Compartment". The coastal compartment between the Chesapeake and Delaware Bays is actually the mosaic of landscapes on the headland of the interfluve that separates these large drainage basins. The coastal compartments form a variety of different-shaped waterways landward of the coastline. Shape differences along the boundaries produce differences in exposure to wind and waves. Different shoreface topographies seaward of the coastline also influence surface roughness by changing wave-refraction patterns. Surface-water roughness (caused by waves) is controlled by a number of parameters, including fetch, shielding, exposure corridors, water-mass boundary conditions, wetland vegetation and water depth in coastal bays. In the coastal ocean, surface roughness patterns are controlled by shoreface shoaling and inlet refraction patterns in the coastal ocean. Knowledge of wave phenomena in the nearshore and backbarrier areas is needed to understand how wave climate influences important ecosystems in estuaries and bays.

Spatial trends in tidal flat shape and associated environmental parameters in South San Francisco Bay

USGS Publications Warehouse

Bearman, J.A.; Friedrichs, Carl T.; Jaffe, B.E.; Foxgrover, A.C.

2010-01-01

Spatial trends in the shape of profiles of South San Francisco Bay (SSFB) tidal flats are examined using bathymetric and lidar data collected in 2004 and 2005. Eigenfunction analysis reveals a dominant mode of morphologic variability related to the degree of convexity or concavity in the cross-shore profileindicative of (i) depositional, tidally dominant or (ii) erosional, wave impacted conditions. Two contrasting areas of characteristic shapenorth or south of a constriction in estuary width located near the Dumbarton Bridgeare recognized. This pattern of increasing or decreasing convexity in the inner or outer estuary is correlated to spatial variability in external and internal environmental parameters, and observational results are found to be largely consistent with theoretical expectations. Tidal flat convexity in SSFB is observed to increase (in decreasing order of significance) in response to increased deposition, increased tidal range, decreased fetch length, decreased sediment grain size, and decreased tidal flat width. ?? 2010 Coastal Education and Research Foundation.

Story-telling, women's authority and the "Old Wife's Tale": "The Story of the Bottle of Medicine".

PubMed

Abrams, Lynn

2012-01-01

The focus of this article is a single personal narrative – a Shetland woman's telling of a story about two girls on a journey to fetch a cure for a sick relative from a wise woman. The story is treated as a cultural document which offers the historian a conduit to a past that is respectful of indigenous woman-centred interpretations of how that past was experienced and understood. The "story of the bottle of medicine" is more than a skilful telling of a local tale; it is a memory practice that provides a path to a deeper and more nuanced understanding of a culture. Applying perspectives from anthropology, oral history and narrative analysis, three sets of questions are addressed: the issue of authenticity; the significance of the narrative structure and storytelling strategies employed; and the nature of the female performance. Ultimately the article asks what this story can tell us about women's interpretation of their own history.

Deltas, freshwater discharge, and waves along the Young Sound, NE Greenland.

PubMed

Kroon, Aart; Abermann, Jakob; Bendixen, Mette; Lund, Magnus; Sigsgaard, Charlotte; Skov, Kirstine; Hansen, Birger Ulf

2017-02-01

A wide range of delta morphologies occurs along the fringes of the Young Sound in Northeast Greenland due to spatial heterogeneity of delta regimes. In general, the delta regime is related to catchment and basin characteristics (geology, topography, drainage pattern, sediment availability, and bathymetry), fluvial discharges and associated sediment load, and processes by waves and currents. Main factors steering the Arctic fluvial discharges into the Young Sound are the snow and ice melt and precipitation in the catchment, and extreme events like glacier lake outburst floods (GLOFs). Waves are subordinate and only rework fringes of the delta plain forming sandy bars if the exposure and fetch are optimal. Spatial gradients and variability in driving forces (snow and precipitation) and catchment characteristics (amount of glacier coverage, sediment characteristics) as well as the strong and local influence of GLOFs in a specific catchment impede a simple upscaling of sediment fluxes from individual catchments toward a total sediment flux into the Young Sound.

Must Metaethical Realism Make a Semantic Claim?

PubMed

Kahane, Guy

2013-02-01

Mackie drew attention to the distinct semantic and metaphysical claims made by meta ethical realists, arguing that although our evaluative discourse is cognitive and objective, there are no objective evaluative facts. This distinction, however, also opens up a reverse possibility: that our evaluative discourse is antirealist, yet objective values do exist. I suggest that this seemingly far-fetched possibility merits serious attention; realism seems com mitted to its intelligibility, and, despite appearances, it isn't incoherent, ineffable, inherently implausible or impossible to defend. I argue that reflection on this possibility should lead us to revise our understanding of the debate between realists and antirealists. It is not only that the realist's semantic claim is insufficient for realism to be true, as Mackie argued; it's not even necessary. Robust metaethical realism is best understood as making a purely metaphysical claim. It is thus not enough for antirealists to show that our discourse is antirealist. They must directly attack the realist's metaphysical claim.

Must Metaethical Realism Make a Semantic Claim?

PubMed Central

Kahane, Guy

2012-01-01

Mackie drew attention to the distinct semantic and metaphysical claims made by meta ethical realists, arguing that although our evaluative discourse is cognitive and objective, there are no objective evaluative facts. This distinction, however, also opens up a reverse possibility: that our evaluative discourse is antirealist, yet objective values do exist. I suggest that this seemingly far-fetched possibility merits serious attention; realism seems com mitted to its intelligibility, and, despite appearances, it isn’t incoherent, ineffable, inherently implausible or impossible to defend. I argue that reflection on this possibility should lead us to revise our understanding of the debate between realists and antirealists. It is not only that the realist’s semantic claim is insufficient for realism to be true, as Mackie argued; it’s not even necessary. Robust metaethical realism is best understood as making a purely metaphysical claim. It is thus not enough for antirealists to show that our discourse is antirealist. They must directly attack the realist’s metaphysical claim. PMID:23525148

JuxtaView - A tool for interactive visualization of large imagery on scalable tiled displays

USGS Publications Warehouse

Krishnaprasad, N.K.; Vishwanath, V.; Venkataraman, S.; Rao, A.G.; Renambot, L.; Leigh, J.; Johnson, A.E.; Davis, B.

2004-01-01

JuxtaView is a cluster-based application for viewing ultra-high-resolution images on scalable tiled displays. We present in JuxtaView, a new parallel computing and distributed memory approach for out-of-core montage visualization, using LambdaRAM, a software-based network-level cache system. The ultimate goal of JuxtaView is to enable a user to interactively roam through potentially terabytes of distributed, spatially referenced image data such as those from electron microscopes, satellites and aerial photographs. In working towards this goal, we describe our first prototype implemented over a local area network, where the image is distributed using LambdaRAM, on the memory of all nodes of a PC cluster driving a tiled display wall. Aggressive pre-fetching schemes employed by LambdaRAM help to reduce latency involved in remote memory access. We compare LambdaRAM with a more traditional memory-mapped file approach for out-of-core visualization. ?? 2004 IEEE.

AmeriFlux US-WPT Winous Point North Marsh

DOE Data Explorer

Chen, Jiquan [University of Toledo / Michigan State University

2016-01-01

This is the AmeriFlux version of the carbon flux data for the site US-WPT Winous Point North Marsh. Site Description - The marsh site has been owned by the Winous Point Shooting Club since 1856 and has been managed by wildlife biologists since 1946. The hydrology of the marsh is relatively isolated by the surrounding dikes and drainages and only receives drainage from nearby croplands through three connecting ditches. Since 2001, the marsh has been managed to maintain year-round inundation with the lowest water levels in September. Within the 0–250 m fetch of the tower, the marsh comprises 42.9% of floating-leaved vegetation, 52.7% of emergent vegetation, and 4.4% of dike and upland during the growing season. Dominant emergent plants include narrow-leaved cattail (Typha angustifolia), rose mallow (Hibiscus moscheutos), and bur reed (Sparganium americanum). Common floating-leaved species are water lily (Nymphaea odorata) and American lotus (Nelumbo lutea) with foliage usually covering the water surface from late May to early October.

SeqDepot: streamlined database of biological sequences and precomputed features.

PubMed

Ulrich, Luke E; Zhulin, Igor B

2014-01-15

Assembling and/or producing integrated knowledge of sequence features continues to be an onerous and redundant task despite a large number of existing resources. We have developed SeqDepot-a novel database that focuses solely on two primary goals: (i) assimilating known primary sequences with predicted feature data and (ii) providing the most simple and straightforward means to procure and readily use this information. Access to >28.5 million sequences and 300 million features is provided through a well-documented and flexible RESTful interface that supports fetching specific data subsets, bulk queries, visualization and searching by MD5 digests or external database identifiers. We have also developed an HTML5/JavaScript web application exemplifying how to interact with SeqDepot and Perl/Python scripts for use with local processing pipelines. Freely available on the web at http://seqdepot.net/. RESTaccess via http://seqdepot.net/api/v1. Database files and scripts maybe downloaded from http://seqdepot.net/download.

The Medical Gopher—A Microcomputer System to Help Find, Organize and Decide About Patient Data

PubMed Central

McDonald, Clement J.; Tierney, William M.

1986-01-01

We have developed a microcomputer-based medical workstation that does some of physicians' “gopher” work of fetching, organizing, reviewing and recording. For two years physicians have used the first version of this system to order all diagnostic tests in a general medicine clinic. They are about to use a newer version to write prescriptions and office visit notes and to find general medical and patient-specific information. Users can enter data into this system by “pointing” with a “mouse” to menu items displayed on a video terminal. In the course of a computer activity, a physician can obtain information about drugs, tests and different diagnoses, as well as about the patient. The microcomputer workstations are linked to each other and to a central hospital information system through a high-speed network link. Our physicians have accepted the initial order-entry system, and early experience suggests they prefer this faster and more sophisticated system. PMID:3811348

Social capital and basic goods: the cautionary tale of drinking water in India.

PubMed

Motiram, Sripad; Osberg, Lars

2010-01-01

This study uses micro-data from the 1998-99 Indian Time Use Survey (ITUS; covering 77,593 persons in 18,591 households in Gujarat, Tamil Nadu, Madhya Pradesh, Meghalaya, Orissa, and Haryana) to argue that time use data provides a natural metric for measuring "social capital" building activities and for distinguishing between the relative importance of "bonding" into groups or "bridging" within communities. The study examines the correlation between inequality in landownership, caste status, measures of local social capital, and whether or not a household will have to collect water. In India, the probability that a rural household fetches water is 4.8% and 9.1% lower in communities in which the average time spent on social interaction and community-based activities at the district-level doubles, but it is 18.9% greater when the time in group-based activities doubles. Inequalities in landownership and home ownership are associated with considerably larger differences in local tap water availability.

RSAT 2015: Regulatory Sequence Analysis Tools

PubMed Central

Medina-Rivera, Alejandra; Defrance, Matthieu; Sand, Olivier; Herrmann, Carl; Castro-Mondragon, Jaime A.; Delerce, Jeremy; Jaeger, Sébastien; Blanchet, Christophe; Vincens, Pierre; Caron, Christophe; Staines, Daniel M.; Contreras-Moreira, Bruno; Artufel, Marie; Charbonnier-Khamvongsa, Lucie; Hernandez, Céline; Thieffry, Denis; Thomas-Chollier, Morgane; van Helden, Jacques

2015-01-01

RSAT (Regulatory Sequence Analysis Tools) is a modular software suite for the analysis of cis-regulatory elements in genome sequences. Its main applications are (i) motif discovery, appropriate to genome-wide data sets like ChIP-seq, (ii) transcription factor binding motif analysis (quality assessment, comparisons and clustering), (iii) comparative genomics and (iv) analysis of regulatory variations. Nine new programs have been added to the 43 described in the 2011 NAR Web Software Issue, including a tool to extract sequences from a list of coordinates (fetch-sequences from UCSC), novel programs dedicated to the analysis of regulatory variants from GWAS or population genomics (retrieve-variation-seq and variation-scan), a program to cluster motifs and visualize the similarities as trees (matrix-clustering). To deal with the drastic increase of sequenced genomes, RSAT public sites have been reorganized into taxon-specific servers. The suite is well-documented with tutorials and published protocols. The software suite is available through Web sites, SOAP/WSDL Web services, virtual machines and stand-alone programs at http://www.rsat.eu/. PMID:25904632

The cognitive ontogeny of tool making in children: The role of inhibition and hierarchical structuring.

PubMed

Gönül, Gökhan; Takmaz, Ece Kamer; Hohenberger, Annette; Corballis, Michael

2018-05-07

During the last decade, the ontogeny of tool making has received growing attention in the literature on tool-related behaviors. However, the cognitive demands underlying tool making are still not clearly understood. In this cross-sectional study of 52 Turkish preschool children from 3 to 6 years of age, the roles of executive function (response inhibition), ability to form hierarchical representations (hierarchical structuring), and social learning were investigated with the hook task previously used with children and animals. In this task, children needed to bend a pipe cleaner to fetch a small bucket with a sticker out of a tall jar. This study replicated earlier findings that preschoolers have great difficulty in tool innovation. However, social learning facilitates tool making, especially after 5 years of age. Capacities to form hierarchical representations and to inhibit prepotent responses were significant positive predictors of tool making after social learning. Copyright © 2018 Elsevier Inc. All rights reserved.

RPython high-level synthesis

NASA Astrophysics Data System (ADS)

Cieszewski, Radoslaw; Linczuk, Maciej

2016-09-01

The development of FPGA technology and the increasing complexity of applications in recent decades have forced compilers to move to higher abstraction levels. Compilers interprets an algorithmic description of a desired behavior written in High-Level Languages (HLLs) and translate it to Hardware Description Languages (HDLs). This paper presents a RPython based High-Level synthesis (HLS) compiler. The compiler get the configuration parameters and map RPython program to VHDL. Then, VHDL code can be used to program FPGA chips. In comparison of other technologies usage, FPGAs have the potential to achieve far greater performance than software as a result of omitting the fetch-decode-execute operations of General Purpose Processors (GPUs), and introduce more parallel computation. This can be exploited by utilizing many resources at the same time. Creating parallel algorithms computed with FPGAs in pure HDL is difficult and time consuming. Implementation time can be greatly reduced with High-Level Synthesis compiler. This article describes design methodologies and tools, implementation and first results of created VHDL backend for RPython compiler.

Real-time analysis of healthcare using big data analytics

NASA Astrophysics Data System (ADS)

Basco, J. Antony; Senthilkumar, N. C.

2017-11-01

Big Data Analytics (BDA) provides a tremendous advantage where there is a need of revolutionary performance in handling large amount of data that covers 4 characteristics such as Volume Velocity Variety Veracity. BDA has the ability to handle such dynamic data providing functioning effectiveness and exceptionally beneficial output in several day to day applications for various organizations. Healthcare is one of the sectors which generate data constantly covering all four characteristics with outstanding growth. There are several challenges in processing patient records which deals with variety of structured and unstructured format. Inducing BDA in to Healthcare (HBDA) will deal with sensitive patient driven information mostly in unstructured format comprising of prescriptions, reports, data from imaging system, etc., the challenges will be overcome by big data with enhanced efficiency in fetching and storing of data. In this project, dataset alike Electronic Medical Records (EMR) produced from numerous medical devices and mobile applications will be induced into MongoDB using Hadoop framework with Improvised processing technique to improve outcome of processing patient records.

a Hadoop-Based Distributed Framework for Efficient Managing and Processing Big Remote Sensing Images

NASA Astrophysics Data System (ADS)

Wang, C.; Hu, F.; Hu, X.; Zhao, S.; Wen, W.; Yang, C.

2015-07-01

Various sensors from airborne and satellite platforms are producing large volumes of remote sensing images for mapping, environmental monitoring, disaster management, military intelligence, and others. However, it is challenging to efficiently storage, query and process such big data due to the data- and computing- intensive issues. In this paper, a Hadoop-based framework is proposed to manage and process the big remote sensing data in a distributed and parallel manner. Especially, remote sensing data can be directly fetched from other data platforms into the Hadoop Distributed File System (HDFS). The Orfeo toolbox, a ready-to-use tool for large image processing, is integrated into MapReduce to provide affluent image processing operations. With the integration of HDFS, Orfeo toolbox and MapReduce, these remote sensing images can be directly processed in parallel in a scalable computing environment. The experiment results show that the proposed framework can efficiently manage and process such big remote sensing data.

Leadership Criteria under Maximum Performance Conditions

DTIC Science & Technology

2011-03-01

other a priori psychological constructs investigated across the maximum and typical performance continuum (Scholtz & Schuler, 1993). While many...reviewed by three trained subject matter experts to ultimately determine a psychological dimension that appropriately captured each input provided. The

Classic maximum entropy recovery of the average joint distribution of apparent FRET efficiency and fluorescence photons for single-molecule burst measurements.

PubMed

DeVore, Matthew S; Gull, Stephen F; Johnson, Carey K

2012-04-05

We describe a method for analysis of single-molecule Förster resonance energy transfer (FRET) burst measurements using classic maximum entropy. Classic maximum entropy determines the Bayesian inference for the joint probability describing the total fluorescence photons and the apparent FRET efficiency. The method was tested with simulated data and then with DNA labeled with fluorescent dyes. The most probable joint distribution can be marginalized to obtain both the overall distribution of fluorescence photons and the apparent FRET efficiency distribution. This method proves to be ideal for determining the distance distribution of FRET-labeled biomolecules, and it successfully predicts the shape of the recovered distributions.

Time Variation of the Distance Separating Bomb and Dive Bomber Subsequent to Bomb Release

NASA Technical Reports Server (NTRS)

Mathews, Charles W.

1952-01-01

A study has been made of the variation of the distance separating bomb and aircraft with time after release as applied to dive-bombing operations, Separation distances determined from this study are presented in terms of two variables only, dive angle and maximum airplane accelerometer reading; the values of separation distance include the effects of delay in initiation of the pull-out and lag in attainment of the maximum normal acceleration.Contains analysis and calculations of the separation distances between bomb and dive bomber following bomb release, Separation distances as determined by the dive angle and the maximum airplane accelerometer reading are presented in a single chart.

Accurate determination of complex materials coefficients of piezoelectric resonators.

PubMed

Du, Xiao-Hong; Wang, Qing-Ming; Uchino, Kenji

2003-03-01

This paper presents a method of accurately determining the complex piezoelectric and elastic coefficients of piezoelectric ceramic resonators from the measurement of the normalized electric admittance, Y, which is electric admittance Y of piezoelectric resonator normalized by the angular frequency omega. The coefficients are derived from the measurements near three special frequency points that correspond to the maximum and the minimum normalized susceptance (B) and the maximum normalized conductance (G). The complex elastic coefficient is determined from the frequencies at these points, and the real and imaginary parts of the piezoelectric coefficient are related to the derivative of the susceptance with respect to the frequency and the asymmetry of the conductance, respectively, near the maximum conductance point. The measurements for some lead zirconate titanate (PZT) based ceramics are used as examples to demonstrate the calculation and experimental procedures and the comparisons with the standard methods.

Variable frequency iteration MPPT for resonant power converters

DOEpatents

Zhang, Qian; Bataresh, Issa; Chen, Lin

2015-06-30

A method of maximum power point tracking (MPPT) uses an MPPT algorithm to determine a switching frequency for a resonant power converter, including initializing by setting an initial boundary frequency range that is divided into initial frequency sub-ranges bounded by initial frequencies including an initial center frequency and first and second initial bounding frequencies. A first iteration includes measuring initial powers at the initial frequencies to determine a maximum power initial frequency that is used to set a first reduced frequency search range centered or bounded by the maximum power initial frequency including at least a first additional bounding frequency. A second iteration includes calculating first and second center frequencies by averaging adjacent frequent values in the first reduced frequency search range and measuring second power values at the first and second center frequencies. The switching frequency is determined from measured power values including the second power values.

Variance Difference between Maximum Likelihood Estimation Method and Expected A Posteriori Estimation Method Viewed from Number of Test Items

ERIC Educational Resources Information Center

Mahmud, Jumailiyah; Sutikno, Muzayanah; Naga, Dali S.

2016-01-01

The aim of this study is to determine variance difference between maximum likelihood and expected A posteriori estimation methods viewed from number of test items of aptitude test. The variance presents an accuracy generated by both maximum likelihood and Bayes estimation methods. The test consists of three subtests, each with 40 multiple-choice…

Maximum Range of a Projectile Thrown from Constant-Speed Circular Motion

ERIC Educational Resources Information Center

Poljak, Nikola

2016-01-01

The problem of determining the angle ? at which a point mass launched from ground level with a given speed v[subscript 0] will reach a maximum distance is a standard exercise in mechanics. There are many possible ways of solving this problem, leading to the well-known answer of ? = p/4, producing a maximum range of D[subscript max] = v[superscript…

Maximum toe flexor muscle strength and quantitative analysis of human plantar intrinsic and extrinsic muscles by a magnetic resonance imaging technique.

PubMed

Kurihara, Toshiyuki; Yamauchi, Junichiro; Otsuka, Mitsuo; Tottori, Nobuaki; Hashimoto, Takeshi; Isaka, Tadao

2014-01-01

The aims of this study were to investigate the relationships between the maximum isometric toe flexor muscle strength (TFS) and cross-sectional area (CSA) of the plantar intrinsic and extrinsic muscles and to identify the major determinant of maximum TFS among CSA of the plantar intrinsic and extrinsic muscles. Twenty six young healthy participants (14 men, 12 women; age, 20.4 ± 1.6 years) volunteered for the study. TFS was measured by a specific designed dynamometer, and CSA of plantar intrinsic and extrinsic muscles were measured using magnetic resonance imaging (MRI). To measure TFS, seated participants optimally gripped the bar with their toes and exerted maximum force on the dynamometer. For each participant, the highest force produced among three trials was used for further analysis. To measure CSA, serial T1-weighted images were acquired. TFS was significantly correlated with CSA of the plantar intrinsic and extrinsic muscles. Stepwise multiple linear regression analyses identified that the major determinant of TFS was CSA of medial parts of plantar intrinsic muscles (flexor hallucis brevis, flexor digitorum brevis, quadratus plantae, lumbricals and abductor hallucis). There was no significant difference between men and women in TFS/CSA. CSA of the plantar intrinsic and extrinsic muscles is one of important factors for determining the maximum TFS in humans.

Using tsunami deposits to determine the maximum depth of benthic burrowing

PubMed Central

Shirai, Kotaro; Murakami-Sugihara, Naoko

2017-01-01

The maximum depth of sediment biomixing is directly related to the vertical extent of post-depositional environmental alteration in the sediment; consequently, it is important to determine the maximum burrowing depth. This study examined the maximum depth of bioturbation in a natural marine environment in Funakoshi Bay, northeastern Japan, using observations of bioturbation structures developed in an event layer (tsunami deposits of the 2011 Tohoku-Oki earthquake) and measurements of the radioactive cesium concentrations in this layer. The observations revealed that the depth of bioturbation (i.e., the thickness of the biomixing layer) ranged between 11 and 22 cm, and varied among the sampling sites. In contrast, the radioactive cesium concentrations showed that the processing of radioactive cesium in coastal environments may include other pathways in addition to bioturbation. The data also revealed the nature of the bioturbation by the heart urchin Echinocardium cordatum (Echinoidea: Loveniidae), which is one of the important ecosystem engineers in seafloor environments. The maximum burrowing depth of E. cordatum in Funakoshi Bay was 22 cm from the seafloor surface. PMID:28854254

Using tsunami deposits to determine the maximum depth of benthic burrowing.

PubMed

Seike, Koji; Shirai, Kotaro; Murakami-Sugihara, Naoko

2017-01-01

The maximum depth of sediment biomixing is directly related to the vertical extent of post-depositional environmental alteration in the sediment; consequently, it is important to determine the maximum burrowing depth. This study examined the maximum depth of bioturbation in a natural marine environment in Funakoshi Bay, northeastern Japan, using observations of bioturbation structures developed in an event layer (tsunami deposits of the 2011 Tohoku-Oki earthquake) and measurements of the radioactive cesium concentrations in this layer. The observations revealed that the depth of bioturbation (i.e., the thickness of the biomixing layer) ranged between 11 and 22 cm, and varied among the sampling sites. In contrast, the radioactive cesium concentrations showed that the processing of radioactive cesium in coastal environments may include other pathways in addition to bioturbation. The data also revealed the nature of the bioturbation by the heart urchin Echinocardium cordatum (Echinoidea: Loveniidae), which is one of the important ecosystem engineers in seafloor environments. The maximum burrowing depth of E. cordatum in Funakoshi Bay was 22 cm from the seafloor surface.

Local magnitude determinations for intermountain seismic belt earthquakes from broadband digital data

USGS Publications Warehouse

Pechmann, J.C.; Nava, S.J.; Terra, F.M.; Bernier, J.C.

2007-01-01

The University of Utah Seismograph Stations (UUSS) earthquake catalogs for the Utah and Yellowstone National Park regions contain two types of size measurements: local magnitude (ML) and coda magnitude (MC), which is calibrated against ML. From 1962 through 1993, UUSS calculated ML values for southern and central Intermountain Seismic Belt earthquakes using maximum peak-to-peak (p-p) amplitudes on paper records from one to five Wood-Anderson (W-A) seismographs in Utah. For ML determinations of earthquakes since 1994, UUSS has utilized synthetic W-A seismograms from U.S. National Seismic Network and UUSS broadband digital telemetry stations in the region, which numbered 23 by the end of our study period on 30 June 2002. This change has greatly increased the percentage of earthquakes for which ML can be determined. It is now possible to determine ML for all M ???3 earthquakes in the Utah and Yellowstone regions and earthquakes as small as M <1 in some areas. To maintain continuity in the magnitudes in the UUSS earthquake catalogs, we determined empirical ML station corrections that minimize differences between MLs calculated from paper and synthetic W-A records. Application of these station corrections, in combination with distance corrections from Richter (1958) which have been in use at UUSS since 1962, produces ML values that do not show any significant distance dependence. ML determinations for the Utah and Yellowstone regions for 1981-2002 using our station corrections and Richter's distance corrections have provided a reliable data set for recalibrating the MC scales for these regions. Our revised ML values are consistent with available moment magnitude determinations for Intermountain Seismic Belt earthquakes. To facilitate automatic ML measurements, we analyzed the distribution of the times of maximum p-p amplitudes in synthetic W-A records. A 30-sec time window for maximum amplitudes, beginning 5 sec before the predicted Sg time, encompasses 95% of the maximum p-p amplitudes. In our judgment, this time window represents a good compromise between maximizing the chances of capturing the maximum amplitude and minimizing the risk of including other seismic events.

Determination of the performance of the Kaplan hydraulic turbines through simplified procedure

NASA Astrophysics Data System (ADS)

Pădureanu, I.; Jurcu, M.; Campian, C. V.; Haţiegan, C.

2018-01-01

A simplified procedure has been developed, compared to the complex one recommended by IEC 60041 (i.e. index samples), for measurement of the performance of the hydraulic turbines. The simplified procedure determines the minimum and maximum powers, the efficiency at maximum power, the evolution of powers by head and flow and to determine the correct relationship between runner/impeller blade angle and guide vane opening for most efficient operation of double-regulated machines. The simplified procedure can be used for a rapid and partial estimation of the performance of hydraulic turbines for repair and maintenance work.

The Impact of Sea Ice Loss on Wave Dynamics and Coastal Erosion Along the Arctic Coast

NASA Astrophysics Data System (ADS)

Overeem, I.; Anderson, R. S.; Wobus, C. W.; Matell, N.; Urban, F. E.; Clow, G. D.; Stanton, T. P.

2010-12-01

The extent of Arctic sea ice has been shrinking rapidly over the past few decades, and attendant acceleration of erosion is now occurring along the Arctic coast. This both brings coastal infrastructure into harm’s way and promotes a complex response of the adjacent landscape to global change. We quantify the effects of declining sea ice extent on coastal erosion rates along a 75-km stretch of coastal permafrost bluffs adjacent to the Beaufort Sea, Alaska, where present-day erosion rates are among the highest in the world at ~14 m yr-1. Our own observations reinforce those of others, and suggest that the rate-limiting process is thermal erosion at the base of the several-meter tall bluffs. Here we focus on the interaction between the nearshore sea ice concentration, the location of the sea ice margin, and the fetch-limited, shallow water wave field, since these parameters ultimately control both sea surface temperatures and the height to which these waters can bathe the frozen bluffs. Thirty years of daily or bi-daily passive microwave data from Nimbus-7 SMMR and DMSP SSM/I satellites reveal that the nearshore open water season lengthened ~54 days over 1979-2009. The open water season, centered in August, expands more rapidly into the fall (September and October~0.92 day yr-1) than into the early summer (July~0.71 days yr-1). Average fetch, defined for our purposes as the distance from the sea ice margin to the coast over which the wind is blowing, increased by a factor 1.7 over the same time-span. Given these time series, we modeled daily nearshore wave heights during the open water season for each year, which we integrated to provide a quantitative metric for the annual exposure of the coastal bluffs to thermal erosion. This “annual wave exposure” increased by 250% during 1979-2009. In the same interval, coastal erosion rates reconstructed from satellite and aerial photo records show less acceleration. We attribute this to a disproportionate extension of the open-water season toward the fall than toward the early summer. This asymmetry fails to tap into the high insolation portion of the summer; expansion into the fall exerts less leverage on coastal change, as sea surface temperatures have significantly declined by late fall. Should the extension of ice-free conditions more strongly advance into the middle of summer, when insolation peaks, we suspect that sea surface temperatures will warm even faster and hence erosion may accelerate yet more strongly.

Multi-GPU Jacobian accelerated computing for soft-field tomography.

PubMed

Borsic, A; Attardo, E A; Halter, R J

2012-10-01

Image reconstruction in soft-field tomography is based on an inverse problem formulation, where a forward model is fitted to the data. In medical applications, where the anatomy presents complex shapes, it is common to use finite element models (FEMs) to represent the volume of interest and solve a partial differential equation that models the physics of the system. Over the last decade, there has been a shifting interest from 2D modeling to 3D modeling, as the underlying physics of most problems are 3D. Although the increased computational power of modern computers allows working with much larger FEM models, the computational time required to reconstruct 3D images on a fine 3D FEM model can be significant, on the order of hours. For example, in electrical impedance tomography (EIT) applications using a dense 3D FEM mesh with half a million elements, a single reconstruction iteration takes approximately 15-20 min with optimized routines running on a modern multi-core PC. It is desirable to accelerate image reconstruction to enable researchers to more easily and rapidly explore data and reconstruction parameters. Furthermore, providing high-speed reconstructions is essential for some promising clinical application of EIT. For 3D problems, 70% of the computing time is spent building the Jacobian matrix, and 25% of the time in forward solving. In this work, we focus on accelerating the Jacobian computation by using single and multiple GPUs. First, we discuss an optimized implementation on a modern multi-core PC architecture and show how computing time is bounded by the CPU-to-memory bandwidth; this factor limits the rate at which data can be fetched by the CPU. Gains associated with the use of multiple CPU cores are minimal, since data operands cannot be fetched fast enough to saturate the processing power of even a single CPU core. GPUs have much faster memory bandwidths compared to CPUs and better parallelism. We are able to obtain acceleration factors of 20 times on a single NVIDIA S1070 GPU, and of 50 times on four GPUs, bringing the Jacobian computing time for a fine 3D mesh from 12 min to 14 s. We regard this as an important step toward gaining interactive reconstruction times in 3D imaging, particularly when coupled in the future with acceleration of the forward problem. While we demonstrate results for EIT, these results apply to any soft-field imaging modality where the Jacobian matrix is computed with the adjoint method.

Etude de la performance des radars hautes-frequences CODAR et WERA pour la mesure des courants marins en presence partielle de glace de mer

NASA Astrophysics Data System (ADS)

Kamli, Emna

Les radars hautes-frequences (RHF) mesurent les courants marins de surface avec une portee pouvant atteindre 200 kilometres et une resolution de l'ordre du kilometre. Cette etude a pour but de caracteriser la performance des RHF, en terme de couverture spatiale, pour la mesure des courants de surface en presence partielle de glace de mer. Pour ce faire, les mesures des courants de deux radars de type CODAR sur la rive sud de l'estuaire maritime du Saint-Laurent, et d'un radar de type WERA sur la rive nord, prises pendant l'hiver 2013, ont ete utilisees. Dans un premier temps, l'aire moyenne journaliere de la zone ou les courants sont mesures par chaque radar a ete comparee a l'energie des vagues de Bragg calculee a partir des donnees brutes d'acceleration fournies par une bouee mouillee dans la zone couverte par les radars. La couverture des CODARs est dependante de la densite d'energie de Bragg, alors que la couverture du WERA y est pratiquement insensible. Un modele de fetch appele GENER a ete force par la vitesse du vent predite par le modele GEM d'Environnement Canada pour estimer la hauteur significative ainsi que la periode modale des vagues. A partir de ces parametres, la densite d'energie des vagues de Bragg a ete evaluee pendant l'hiver a l'aide du spectre theorique de Bretschneider. Ces resultats permettent d'etablir la couverture normale de chaque radar en absence de glace de mer. La concentration de glace de mer, predite par le systeme canadien operationnel de prevision glace-ocean, a ete moyennee sur les differents fetchs du vent selon la direction moyenne journaliere des vagues predites par GENER. Dans un deuxieme temps, la relation entre le ratio des couvertures journalieres obtenues pendant l'hiver 2013 et des couvertures normales de chaque radar d'une part, et la concentration moyenne journaliere de glace de mer d'autre part, a ete etablie. Le ratio des couvertures decroit avec l'augmentation de la concentration de glace de mer pour les deux types de radars, mais pour une concentration de glace de 20% la couverture du WERA est reduite de 34% alors que pour les CODARs elle est reduite de 67%. Les relations empiriques etablies entre la couverture des RHF et les parametres environnementaux (vent et glace de mer) permettront de predire la couverture que pourraient fournir des RHF installes dans d'autres regions soumises a la presence saisonniere de glace de mer.

Multi-GPU Jacobian Accelerated Computing for Soft Field Tomography

PubMed Central

Borsic, A.; Attardo, E. A.; Halter, R. J.

2012-01-01

Image reconstruction in soft-field tomography is based on an inverse problem formulation, where a forward model is fitted to the data. In medical applications, where the anatomy presents complex shapes, it is common to use Finite Element Models to represent the volume of interest and to solve a partial differential equation that models the physics of the system. Over the last decade, there has been a shifting interest from 2D modeling to 3D modeling, as the underlying physics of most problems are three-dimensional. Though the increased computational power of modern computers allows working with much larger FEM models, the computational time required to reconstruct 3D images on a fine 3D FEM model can be significant, on the order of hours. For example, in Electrical Impedance Tomography applications using a dense 3D FEM mesh with half a million elements, a single reconstruction iteration takes approximately 15 to 20 minutes with optimized routines running on a modern multi-core PC. It is desirable to accelerate image reconstruction to enable researchers to more easily and rapidly explore data and reconstruction parameters. Further, providing high-speed reconstructions are essential for some promising clinical application of EIT. For 3D problems 70% of the computing time is spent building the Jacobian matrix, and 25% of the time in forward solving. In the present work, we focus on accelerating the Jacobian computation by using single and multiple GPUs. First, we discuss an optimized implementation on a modern multi-core PC architecture and show how computing time is bounded by the CPU-to-memory bandwidth; this factor limits the rate at which data can be fetched by the CPU. Gains associated with use of multiple CPU cores are minimal, since data operands cannot be fetched fast enough to saturate the processing power of even a single CPU core. GPUs have a much faster memory bandwidths compared to CPUs and better parallelism. We are able to obtain acceleration factors of 20 times on a single NVIDIA S1070 GPU, and of 50 times on 4 GPUs, bringing the Jacobian computing time for a fine 3D mesh from 12 minutes to 14 seconds. We regard this as an important step towards gaining interactive reconstruction times in 3D imaging, particularly when coupled in the future with acceleration of the forward problem. While we demonstrate results for Electrical Impedance Tomography, these results apply to any soft-field imaging modality where the Jacobian matrix is computed with the Adjoint Method. PMID:23010857

The Influence of the Form of a Wooden Beam on Its Stiffness and Strength III : Stresses in Wood Members Subjected to Combined Column and Beam Action

NASA Technical Reports Server (NTRS)

Newlin, J A; Trayer, G W

1925-01-01

The general purpose in this study was to determine the stresses in a wooden member subjected to combined beam and column action. What may be considered the specific purpose, as it relates more directly to the problem of design, was to determine the particular stress that obtains at maximum load which, for combined loading, does not occur simultaneously with maximum stress.

LEOS 1992 - Summer Topical Meeting Digest Held in Santa Barbara, California on July 29-12 August, 1992

DTIC Science & Technology

1992-01-01

careful design of the device to maximise the relaxation oscillation resonance frequency [2], minimize leakage currents [2,3], and optimize other...and determines the maximum frequency of operation. With hybrid circuit construction this maximum frequency would generally be in the order of a few...operating at a frequency of 335.48 MHz. The resultant timing jitter is determined by sending both pulse trains into a rotating mirror optical

Biofilm development in fixed bed biofilm reactors: experiments and simple models for engineering design purposes.

PubMed

Szilágyi, N; Kovács, R; Kenyeres, I; Csikor, Zs

2013-01-01

Biofilm development in a fixed bed biofilm reactor system performing municipal wastewater treatment was monitored aiming at accumulating colonization and maximum biofilm mass data usable in engineering practice for process design purposes. Initially a 6 month experimental period was selected for investigations where the biofilm formation and the performance of the reactors were monitored. The results were analyzed by two methods: for simple, steady-state process design purposes the maximum biofilm mass on carriers versus influent load and a time constant of the biofilm growth were determined, whereas for design approaches using dynamic models a simple biofilm mass prediction model including attachment and detachment mechanisms was selected and fitted to the experimental data. According to a detailed statistical analysis, the collected data have not allowed us to determine both the time constant of biofilm growth and the maximum biofilm mass on carriers at the same time. The observed maximum biofilm mass could be determined with a reasonable error and ranged between 438 gTS/m(2) carrier surface and 843 gTS/m(2), depending on influent load, and hydrodynamic conditions. The parallel analysis of the attachment-detachment model showed that the experimental data set allowed us to determine the attachment rate coefficient which was in the range of 0.05-0.4 m d(-1) depending on influent load and hydrodynamic conditions.

Bridge-scour analysis on Cuchillo Negro Creek at the Interstate 25 crossing near Truth or Consequences, New Mexico

USGS Publications Warehouse

Waltemeyer, S.D.

1995-01-01

A sediment-transport model to simulate channel change was applied to a 1-mile reach of Cuchillo Negro Creek at the Interstate 25 crossing at Truth or Consequences, New Mexico, using the Bridge-Stream Tube model for Alluvial River Simulation (BRI-STARS). The 500-year flood discharge was estimated to be 10,700 cubic feet per second. The 100-year, 500-year, and regional maximum discharges were used to design synthetic and discretized hydrographs using a flood volume equation. The regional maximum discharge relation was developed for New Mexico based on 259 streamflow-gaging stations' maximum peak discharge. The regional maximum-peak discharge for the site was determined to be 81,700 cubic feet per second. Bed-material particle-size distribution was determined for six size classes ranging from 1 to 30 millimeters. The median diameter was 4.6 millimeters at the bed surface and 9.0 millimeters 13 feet below the bed surface. Bed-material discharge for use in the model was estimated to be 18,770 tons per day using hydraulic properties, water temperature, and Yang's gravel equation. Channel-change simulations showed a maximum channel degradation of 1.38 feet for the regional maximum-peak discharge hydrograph.

Improving a maximum horizontal gradient algorithm to determine geological body boundaries and fault systems based on gravity data

NASA Astrophysics Data System (ADS)

Van Kha, Tran; Van Vuong, Hoang; Thanh, Do Duc; Hung, Duong Quoc; Anh, Le Duc

2018-05-01

The maximum horizontal gradient method was first proposed by Blakely and Simpson (1986) for determining the boundaries between geological bodies with different densities. The method involves the comparison of a center point with its eight nearest neighbors in four directions within each 3 × 3 calculation grid. The horizontal location and magnitude of the maximum values are found by interpolating a second-order polynomial through the trio of points provided that the magnitude of the middle point is greater than its two nearest neighbors in one direction. In theoretical models of multiple sources, however, the above condition does not allow the maximum horizontal locations to be fully located, and it could be difficult to correlate the edges of complicated sources. In this paper, the authors propose an additional condition to identify more maximum horizontal locations within the calculation grid. This additional condition will improve the method algorithm for interpreting the boundaries of magnetic and/or gravity sources. The improved algorithm was tested on gravity models and applied to gravity data for the Phu Khanh basin on the continental shelf of the East Vietnam Sea. The results show that the additional locations of the maximum horizontal gradient could be helpful for connecting the edges of complicated source bodies.

Attitude determination and calibration using a recursive maximum likelihood-based adaptive Kalman filter

NASA Technical Reports Server (NTRS)

Kelly, D. A.; Fermelia, A.; Lee, G. K. F.

1990-01-01

An adaptive Kalman filter design that utilizes recursive maximum likelihood parameter identification is discussed. At the center of this design is the Kalman filter itself, which has the responsibility for attitude determination. At the same time, the identification algorithm is continually identifying the system parameters. The approach is applicable to nonlinear, as well as linear systems. This adaptive Kalman filter design has much potential for real time implementation, especially considering the fast clock speeds, cache memory and internal RAM available today. The recursive maximum likelihood algorithm is discussed in detail, with special attention directed towards its unique matrix formulation. The procedure for using the algorithm is described along with comments on how this algorithm interacts with the Kalman filter.

Classic Maximum Entropy Recovery of the Average Joint Distribution of Apparent FRET Efficiency and Fluorescence Photons for Single-molecule Burst Measurements

PubMed Central

DeVore, Matthew S.; Gull, Stephen F.; Johnson, Carey K.

2012-01-01

We describe a method for analysis of single-molecule Förster resonance energy transfer (FRET) burst measurements using classic maximum entropy. Classic maximum entropy determines the Bayesian inference for the joint probability describing the total fluorescence photons and the apparent FRET efficiency. The method was tested with simulated data and then with DNA labeled with fluorescent dyes. The most probable joint distribution can be marginalized to obtain both the overall distribution of fluorescence photons and the apparent FRET efficiency distribution. This method proves to be ideal for determining the distance distribution of FRET-labeled biomolecules, and it successfully predicts the shape of the recovered distributions. PMID:22338694

The use of a numerical method to justify the criteria for the maximum settlement of the tank foundation

NASA Astrophysics Data System (ADS)

Tarasenko, Alexander; Chepur, Petr; Gruchenkova, Alesya

2017-11-01

The article examines the problem of assessing the permissible values of uneven settlement for a vertical steel tank base and foundation. A numerical experiment was performed using a finite element model of the tank. The model took into account the geometric shape of the structure and its additional stiffening elements that affect the stress-strain state of the tank. An equation was obtained that allowed determining the maximum possible deformation of the bottom outer contour during uneven settlement. Depending on the length of the uneven settlement zone, the values of the permissible settlement of the tank base were determined. The article proposes new values of the maximum permissible tank settlement with additional stiffening elements.

System and method for the adaptive mapping of matrix data to sets of polygons

NASA Technical Reports Server (NTRS)

Burdon, David (Inventor)

2003-01-01

A system and method for converting bitmapped data, for example, weather data or thermal imaging data, to polygons is disclosed. The conversion of the data into polygons creates smaller data files. The invention is adaptive in that it allows for a variable degree of fidelity of the polygons. Matrix data is obtained. A color value is obtained. The color value is a variable used in the creation of the polygons. A list of cells to check is determined based on the color value. The list of cells to check is examined in order to determine a boundary list. The boundary list is then examined to determine vertices. The determination of the vertices is based on a prescribed maximum distance. When drawn, the ordered list of vertices create polygons which depict the cell data. The data files which include the vertices for the polygons are much smaller than the corresponding cell data files. The fidelity of the polygon representation can be adjusted by repeating the logic with varying fidelity values to achieve a given maximum file size or a maximum number of vertices per polygon.

Final Report - Management of High Sulfur HLW, VSL-13R2920-1, Rev. 0, dated 10/31/2013

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kruger, Albert A.; Gan, H.; Pegg, I. L.

2013-11-13

The present report describes results from a series of small-scale crucible tests to determine the extent of corrosion associated with sulfur containing HLW glasses and to develop a glass composition for a sulfur-rich HLW waste stream, which was then subjected to small-scale melter testing to determine the maximum acceptable sulfate loadings. In the present work, a new glass formulation was developed and tested for a projected Hanford HLW composition with sulfate concentrations high enough to limit waste loading. Testing was then performed on the DM10 melter system at successively higher waste loadings to determine the maximum waste loading without themore » formation of a separate sulfate salt phase. Small scale corrosion testing was also conducted using the glass developed in the present work, the glass developed in the initial phase of this work [26], and a high iron composition, all at maximum sulfur concentrations determined from melter testing, in order to assess the extent of Inconel 690 and MA758 corrosion at elevated sulfate contents.« less

Igniter adapter-to-igniter chamber deflection test

NASA Technical Reports Server (NTRS)

Cook, M.

1990-01-01

Testing was performed to determine the maximum RSRM igniter adapter-to-igniter chamber joint deflection at the crown of the inner joint primary seal. The deflection data was gathered to support igniter inner joint gasket resiliency predictions which led to launch commit criteria temperature determinations. The proximity (deflection) gage holes for the first test (Test No. 1) were incorrectly located; therefore, the test was declared a non-test. Prior to Test No. 2, test article configuration was modified with the correct proximity gage locations. Deflection data were successfully acquired during Test No. 2. However, the proximity gage deflection measurements were adversely affected by temperature increases. Deflections measured after the temperature rise at the proximity gages were considered unreliable. An analysis was performed to predict the maximum deflections based on the reliable data measured before the detectable temperature rise. Deflections to the primary seal crown location were adjusted to correspond to the time of maximum expected operating pressure (2,159 psi) to account for proximity gage bias, and to account for maximum attach and special bolt relaxation. The maximum joint deflection for the igniter inner joint at the crown of the primary seal, accounting for all significant correction factors, was 0.0031 in. (3.1 mil). Since the predicted (0.003 in.) and tested maximum deflection values were sufficiently close, the launch commit criteria was not changed as a result of this test. Data from this test should be used to determine if the igniter inner joint gasket seals are capable of maintaining sealing capability at a joint displacement of (1.4) x (0.0031 in.) = 0.00434 inches. Additional testing should be performed to increase the database on igniter deflections and address launch commit criteria temperatures.

The tolerance efficiency of Panicum maximum and Helianthus annuus in TNT-contaminated soil and nZVI-contaminated soil.

PubMed

Jiamjitrpanich, Waraporn; Parkpian, Preeda; Polprasert, Chongrak; Laurent, François; Kosanlavit, Rachain

2012-01-01

This study was designed to compare the initial method for phytoremediation involving germination and transplantation. The study was also to determine the tolerance efficiency of Panicum maximum (Purple guinea grass) and Helianthus annuus (Sunflower) in TNT-contaminated soil and nZVI-contaminated soil. It was found that the transplantation of Panicum maximum and Helianthus annuus was more suitable than germination as the initiate method of nano-phytoremediation potting test. The study also showed that Panicum maximum was more tolerance than Helianthus annuus in TNT and nZVI-contaminated soil. Therefore, Panicum maximum in the transplantation method should be selected as a hyperaccumulated plant for nano-phytoremediation potting tests. Maximum tolerance dosage of Panicum maximum to TNT-concentration soil was 320 mg/kg and nZVI-contaminated soil was 1000 mg/kg in the transplantation method.

Predicting the Maximum Dynamic Strength in Bench Press: The High Precision of the Bar Velocity Approach.

PubMed

Loturco, Irineu; Kobal, Ronaldo; Moraes, José E; Kitamura, Katia; Cal Abad, César C; Pereira, Lucas A; Nakamura, Fábio Y

2017-04-01

Loturco, I, Kobal, R, Moraes, JE, Kitamura, K, Cal Abad, CC, Pereira, LA, and Nakamura, FY. Predicting the maximum dynamic strength in bench press: the high precision of the bar velocity approach. J Strength Cond Res 31(4): 1127-1131, 2017-The aim of this study was to determine the force-velocity relationship and test the possibility of determining the 1 repetition maximum (1RM) in "free weight" and Smith machine bench presses. Thirty-six male top-level athletes from 3 different sports were submitted to a standardized 1RM bench press assessment (free weight or Smith machine, in randomized order), following standard procedures encompassing lifts performed at 40-100% of 1RM. The mean propulsive velocity (MPV) was measured in all attempts. A linear regression was performed to establish the relationships between bar velocities and 1RM percentages. The actual and predicted 1RM for each exercise were compared using a paired t-test. Although the Smith machine 1RM was higher (10% difference) than the free weight 1RM, in both cases the actual and predicted values did not differ. In addition, the linear relationship between MPV and percentage of 1RM (coefficient of determination ≥95%) allow determination of training intensity based on the bar velocity. The linear relationships between the MPVs and the relative percentages of 1RM throughout the entire range of loads enable coaches to use the MPV to accurately monitor their athletes on a daily basis and accurately determine their actual 1RM without the need to perform standard maximum dynamic strength assessments.

Global Solar Magnetology and Reference Points of the Solar Cycle

NASA Astrophysics Data System (ADS)

Obridko, V. N.; Shelting, B. D.

2003-11-01

The solar cycle can be described as a complex interaction of large-scale/global and local magnetic fields. In general, this approach agrees with the traditional dynamo scheme, although there are numerous discrepancies in the details. Integrated magnetic indices introduced earlier are studied over long time intervals, and the epochs of the main reference points of the solar cycles are refined. A hypothesis proposed earlier concerning global magnetometry and the natural scale of the cycles is verified. Variations of the heliospheric magnetic field are determined by both the integrated photospheric i(B r )ph and source surface i(B r )ss indices, however, their roles are different. Local fields contribute significantly to the photospheric index determining the total increase in the heliospheric magnetic field. The i(B r )ss index (especially the partial index ZO, which is related to the quasi-dipolar field) determines narrow extrema. These integrated indices supply us with a “passport” for reference points, making it possible to identify them precisely. A prominent dip in the integrated indices is clearly visible at the cycle maximum, resulting in the typical double-peak form (the Gnevyshev dip), with the succeeding maximum always being higher than the preceding maximum. At the source surface, this secondary maximum significantly exceeds the primary maximum. Using these index data, we can estimate the progression expected for the 23rd cycle and predict the dates of the ends of the 23rd and 24th cycles (the middle of 2007 and December 2018, respectively).

The effect of adhesive strength of hydroxyapatite coating on the stability of hydroxyapatite-coated prostheses in vivo at the early stage of implantation

PubMed Central

Duan, Yonghong; Zhu, Shu; Guo, Fei; Zhu, Jinyu; Li, Mao; Ma, Jie

2012-01-01

Introduction With the increase in joint revision surgery after arthroplasty, defects of hydroxyapatite (HA)-coated prostheses have been observed increasingly often. These defects adversely affect the prosthetic stability in vivo. This study has analyzed the potential effect of the adhesive strength of HA coating on the stability of HA-coated prostheses in vivo after its implantation. Material and methods Sixty experimental rabbits were divided into HA- and Ti-coated groups. HA-coated prostheses were implanted into the bilateral epicondyle of rabbits femurs. Ti-coated prostheses were implanted as control. At different time points(4, 9, and 15 weeks) after implantation, bone tissue samples were fetched out respectively for histomorphometric analysis. Push-out testing was used to detect the ultimate shear strength at the bone-prosthesis interface. Scanning electron microscope (SEM) observation and energy-dispersive X-ray spectroscopy (EDX) analysis were used to observe the changes in surface composition of the prostheses after the ultimate shear strength testing. The coating adhesive strength of two kinds of coatings were also examined by scratch testing. Results Hydroxyapatite coating has an obvious advantage in facilitating osteogenesis and its plays a critical role in the stability of prostheses. However, the ultimate shear strength of HA-coated prostheses is much lower than that of Ti-coated implants (p < 0.01). Further study has demonstrated that the stability of HA-coated prostheses in vivo is affected by the relatively low adhesive strength between coating and substrate. Conclusions Obvious advantage in facilitating osteogenesis around HA-coated prostheses is not the only factor that determines the stability of prostheses in vivo. PMID:22661990

Characteristics of Wind Generated Waves in the Delaware Estuary

NASA Astrophysics Data System (ADS)

Chen, J. L.; Ralston, D. K.; Geyer, W. R.; Chant, R. J.; Sommerfield, C. K.

2016-02-01

Coastal marshes provide important services for human uses such as fishery industry, recreation, ports and marine operations. Bombay Hook Wildlife Refuge, located along the western shore of the Delaware Estuary, has experienced substantial loss of salt marsh in recent decades. To evaluate the importance of different mechanisms which cause observed shoreline retreat, wave gauges were deployed along the dredged navigation channel and shoreline in the Delaware Estuary. A coupled wave and circulation modeling system (SWAN/ROMS) based on the most recent bathymetry (last updated 2013) is validated with waves observed during both calm and energetic conditions in November 2015. Simulation results based on different model parameterizations of whitecapping, bottom friction and the wind input source are compared. The tendency of observed wave steepness is more similar to a revised whitecapping source term [Westhuysen, 2007] than the default in SWAN model. Both model results and field data show that the generation/dissipation of waves in the Delaware estuary is determined by the local wind speed and channel depth. Whitecapping-induced energy dissipation is dominant in the channel, while dissipation due to bottom friction and depth-induced breaking become important on lateral shoals. To characterize the effects of wind fetch on waves in estuaries more generally, simulations with an idealized domain and varying wind conditions are compared and the results are expressed in terms of non-dimensional parameters. The simulations based on a 10m-depth uniform idealized channel show that the dissipation of waves is mainly controlled by whitecapping in all wind conditions. Under strong wind conditions (wind speed >10m/s) the effect of bottom friction becomes important so the simulated wave heights are no longer linearly correlated with wind speed.

Protocol for a randomised, placebo-controlled pilot study for assessing feasibility and efficacy of faecal microbiota transplantation in a paediatric ulcerative colitis population: PediFETCh trial

PubMed Central

Popov, Jelena

2017-01-01

Introduction Ulcerative colitis (UC) is a chronic, relapsing condition characterised by colonic inflammation. Increasing prevalence in early-age diagnosis provides opportunities for additional complications in later life as a result of prolonged exposure to inflammatory and therapeutic insults, necessitating novel avenues for therapeutics which may result in fewer side effects. Faecal microbiota transplantation (FMT) has previously demonstrated potential therapeutic benefit in an adult randomised-controlled trial and several recurrent Clostridium difficile infection studies. This phase Ib pilot will be the first randomised, single-blinded, placebo-controlled trial to assess feasibility and patient outcomes in a paediatric inflammatory bowel disease (IBD) population. Methods and analysis Fifty patients will be randomised 1:1 to receive normal saline control or active sample. Enema administrations will be performed two times per week for 6 weeks, followed at a 6-month follow-up period. Feasibility outcomes will include measures of patient eligibility, recruitment, willingness to participate, samples collections, hospitalizations and drop-out rate. Improvements in disease symptoms will determine the efficacy of treatment. Clinical disease scores will be taken throughout the study period using the Paediatric Ulcerative Colitis Activity Index (PUCAI). Monitoring of inflammatory markers in blood and stool will be performed at regular intervals. Microbiome analysis will be conducted on stool samples collected throughout the trials period. Imaging and endoscopic surveillance will be conducted if clinically necessary. Ethics and dissemination Ethics was obtained from local hospital research ethics boards across all three sites. Health Canada and FDA approval was obtained for the use of an Investigatory New Drug product. Results from this trial will be presented in international conferences and published in peer-review journals. Trial registration number Trial registration number: NCT02487238; preresults. PMID:28827258

40 CFR 60.116b - Monitoring of operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... range. (e) Available data on the storage temperature may be used to determine the maximum true vapor...: (i) Available data on the Reid vapor pressure and the maximum expected storage temperature based on... Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction...

The effects of age and type of carrying task on lower extremity kinematics

PubMed Central

Gillette, Jason C.; Stevermer, Catherine A.; Miller, Ross H.; Meardon, Stacey A.; Schwab, Charles V.

2009-01-01

The purpose of this study was to determine the effects of age, load amount, and load symmetry on lower extremity kinematics during carrying tasks. Forty-two participants in four age groups (8-10 years, 12-14 years, 15-17 years, and adults) carried loads of 0%, 10%, and 20% body weight (BW) in large or small buckets unilaterally and bilaterally. Reflective markers were tracked to determine total joint ROM and maximum joint angles during the stance phase of walking. Maximum hip extension, hip adduction, and hip internal rotation angles were significantly greater for each of the child/adolescent age groups as compared to adults. In addition, maximum hip internal rotation angles significantly increased when carrying a 20% BW load. The observation that the 8-10 year old age group carried the lightest absolute loads and still displayed the highest maximum hip internal rotation angles suggests a particular necessity in setting carrying guidelines for the youngest children. PMID:20191410

Comparative Analysis of Reduced-Rule Compressed Fuzzy Logic Control and Incremental Conductance MPPT Methods

NASA Astrophysics Data System (ADS)

Kandemir, Ekrem; Borekci, Selim; Cetin, Numan S.

2018-04-01

Photovoltaic (PV) power generation has been widely used in recent years, with techniques for increasing the power efficiency representing one of the most important issues. The available maximum power of a PV panel is dependent on environmental conditions such as solar irradiance and temperature. To extract the maximum available power from a PV panel, various maximum-power-point tracking (MPPT) methods are used. In this work, two different MPPT methods were implemented for a 150-W PV panel. The first method, known as incremental conductance (Inc. Cond.) MPPT, determines the maximum power by measuring the derivative of the PV voltage and current. The other method is based on reduced-rule compressed fuzzy logic control (RR-FLC), using which it is relatively easier to determine the maximum power because a single input variable is used to reduce computing loads. In this study, a 150-W PV panel system model was realized using these MPPT methods in MATLAB and the results compared. According to the simulation results, the proposed RR-FLC-based MPPT could increase the response rate and tracking accuracy by 4.66% under standard test conditions.

A new method for solving reachable domain of spacecraft with a single impulse

NASA Astrophysics Data System (ADS)

Chen, Qi; Qiao, Dong; Shang, Haibin; Liu, Xinfu

2018-04-01

This paper develops a new approach to solve the reachable domain of a spacecraft with a single maximum available impulse. First, the distance in a chosen direction, started from a given position on the initial orbit, is formulated. Then, its extreme value is solved to obtain the maximum reachable distance in this direction. The envelop of the reachable domain in three-dimensional space is determined by solving the maximum reachable distance in all directions. Four scenarios are analyzed, including three typical scenarios (either the maneuver position or impulse direction is fixed, or both are arbitrary) and a new extended scenario (the maneuver position is restricted to an interval and the impulse direction is arbitrary). Moreover, the symmetry and the boundedness of the reachable domain are discussed in detail. The former is helpful to reduce the numerical computation, while the latter decides the maximum eccentricity of the initial orbit for a maximum available impulse. The numerical simulations verify the effectiveness of the proposed method for solving the reachable domain in all four scenarios. Especially, the reachable domain with a highly elliptical initial orbit can be determined successfully, which remains unsolved in the existing papers.

Fluid-inclusion technique for determining maximum temperature in calcite and its comparison to the vitrinite reflectance geothermometer

USGS Publications Warehouse

Barker, C.E.; Goldstein, R.H.

1990-01-01

The hypothesis that aqueous fluid inclusions in calcite can be used to establish maximum temperature (Tpeak) is tested. Fluid inclusion Th, mean random vitrinite reflectance (Rm), and present-day Tpeak from 46 diverse geologic systems that have been at Tpeak from 104 to 106 yr have been compiled. Present Tpeak ranged from 65 to 345??C, Th modes and means ranged from 59 to 350??C, and Rm data ranged from 0.4% to 4.6%, spanning the temperature and thermal maturity range associated with burial diagenesis, hydrothermal alteration, and low-grade metamorphism. Plots of Th and Tpeak data for systems thought to be currently at maximum temperature demonstrate close agreement between Th and present Tpeak in sedimentary basins. The relation suggests that Th of aqueous fluid inclusions in calcite may be a useful measure of maximum temperature. This study also compared Th to mean random vitrinite reflectance (Rm). Th correlates well with Rm and results in a curve similar to Rm vs. Tpeak calibrations determined by other workers. Strong correlation between Tpeak and Rm in these systems suggests that maximum temperature is the major control on thermal maturation. -after Authors

A New Method to Measure Temperature and Burner Pattern Factor Sensing for Active Engine Control

NASA Technical Reports Server (NTRS)

Ng, Daniel

1999-01-01

The determination of the temperatures of extended surfaces which exhibit non-uniform temperature variation is very important for a number of applications including the "Burner Pattern Factor" (BPF) of turbine engines. Exploratory work has shown that use of BPF to control engine functions can result in many benefits, among them reduction in engine weight, reduction in operating cost, increase in engine life, while attaining maximum engine efficiency. Advanced engines are expected to operate at very high temperature to achieve high efficiency. Brief exposure of engine components to higher than design temperatures due to non-uniformity in engine burner pattern can reduce engine life. The engine BPF is a measure of engine temperature uniformity. Attainment of maximum temperature uniformity and high temperatures is key to maximum efficiency and long life. A new approach to determine through the measurement of just one radiation spectrum by a multiwavelength pyrometer is possible. This paper discusses a new temperature sensing approach and its application to determine the BPF.

Temperature, stress, and corrosive sensing apparatus utilizing harmonic response of magnetically soft sensor element (s)

NASA Technical Reports Server (NTRS)

Grimes, Craig A. (Inventor); Ong, Keat Ghee (Inventor)

2003-01-01

A temperature sensing apparatus including a sensor element made of a magnetically soft material operatively arranged within a first and second time-varying interrogation magnetic field, the first time-varying magnetic field being generated at a frequency higher than that for the second magnetic field. A receiver, remote from the sensor element, is engaged to measure intensity of electromagnetic emissions from the sensor element to identify a relative maximum amplitude value for each of a plurality of higher-order harmonic frequency amplitudes so measured. A unit then determines a value for temperature (or other parameter of interst) using the relative maximum harmonic amplitude values identified. In other aspects of the invention, the focus is on an apparatus and technique for determining a value for of stress condition of a solid analyte and for determining a value for corrosion, using the relative maximum harmonic amplitude values identified. A magnetically hard element supporting a biasing field adjacent the magnetically soft sensor element can be included.

An investigation of FT-Raman spectroscopy for quantification of additives to milk

USDA-ARS?s Scientific Manuscript database

In this research, four chemicals, urea, ammonium sulfate, dicyandiamide, and melamine, were mixed into liquid nonfat milk at concentrations starting from 0.1% to a maximum concentration determined for each chemical according to its maximum solubility, and two Raman spectrometers—a commercial Nicolet...

14 CFR 23.1563 - Airspeed placards.

Code of Federal Regulations, 2014 CFR

2014-01-01

... multiengine-powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes, the maximum value of the minimum control speed, VMC (one-engine-inoperative) determined under § 23.149... control and the airspeed indicator has features such as low speed awareness that provide ample warning...

14 CFR 23.1563 - Airspeed placards.

Code of Federal Regulations, 2013 CFR

2013-01-01

... multiengine-powered airplanes of more than 6,000 pounds maximum weight, and turbine engine-powered airplanes, the maximum value of the minimum control speed, VMC (one-engine-inoperative) determined under § 23.149... control and the airspeed indicator has features such as low speed awareness that provide ample warning...

Maximum likelihood phase-retrieval algorithm: applications.

PubMed

Nahrstedt, D A; Southwell, W H

1984-12-01

The maximum likelihood estimator approach is shown to be effective in determining the wave front aberration in systems involving laser and flow field diagnostics and optical testing. The robustness of the algorithm enables convergence even in cases of severe wave front error and real, nonsymmetrical, obscured amplitude distributions.

Dependence of driving characteristics upon follower-leader combination

NASA Astrophysics Data System (ADS)

Nagahama, Akihito; Yanagisawa, Daichi; Nishinari, Katsuhiro

2017-10-01

The analysis of the microscopic view of mixed traffic offers a basis for resolving traffic jams which are inhomogeneous due to several types of vehicles. In this study, we research the dependence of driving characteristics upon vehicle order in a platoon. By focusing particularly upon the manner in which the driving characteristics of a follower are affected by both their own vehicle type and that of their leader, we measured the trajectories of platoons comprising two vehicles selected from motorcycles, passenger cars, and trucks on a test course. Analysis based on vehicle order showed that the vehicle types of both the leader and the follower as well as the leader's driving characteristics affected the velocity, acceleration, deceleration, operational delay of followers, and the distance gap between leaders and followers in different ways. In addition, we investigated the factors affecting driving characteristics by multiple regression analysis. We revealed that the operational delay and the maximum distance gap tend to be large when the length of leaders is large. Furthermore, as long as a follower can follow, we need not consider vehicle types among the parameters determining maximum velocity in car-following models. The vehicle types of the leader and the follower should be considered to determine maximum acceleration. When determining maximum deceleration, the vehicle types of the follower should be considered.

A Maximum Likelihood Approach to Determine Sensor Radiometric Response Coefficients for NPP VIIRS Reflective Solar Bands

NASA Technical Reports Server (NTRS)

Lei, Ning; Chiang, Kwo-Fu; Oudrari, Hassan; Xiong, Xiaoxiong

2011-01-01

Optical sensors aboard Earth orbiting satellites such as the next generation Visible/Infrared Imager/Radiometer Suite (VIIRS) assume that the sensors radiometric response in the Reflective Solar Bands (RSB) is described by a quadratic polynomial, in relating the aperture spectral radiance to the sensor Digital Number (DN) readout. For VIIRS Flight Unit 1, the coefficients are to be determined before launch by an attenuation method, although the linear coefficient will be further determined on-orbit through observing the Solar Diffuser. In determining the quadratic polynomial coefficients by the attenuation method, a Maximum Likelihood approach is applied in carrying out the least-squares procedure. Crucial to the Maximum Likelihood least-squares procedure is the computation of the weight. The weight not only has a contribution from the noise of the sensor s digital count, with an important contribution from digitization error, but also is affected heavily by the mathematical expression used to predict the value of the dependent variable, because both the independent and the dependent variables contain random noise. In addition, model errors have a major impact on the uncertainties of the coefficients. The Maximum Likelihood approach demonstrates the inadequacy of the attenuation method model with a quadratic polynomial for the retrieved spectral radiance. We show that using the inadequate model dramatically increases the uncertainties of the coefficients. We compute the coefficient values and their uncertainties, considering both measurement and model errors.

Method and apparatus for determining peak temperature along an optical fiber

DOEpatents

Fox, R.J.

1982-07-29

The invention relates to a new method and new apparatus for determining the hottest temperature or the coldest temperature prevailing along the length of an optical-fiber light guide. The invention is conducted with an optical fiber capable of supporting multidiode propagation of light and comprising a core, a cladding, and a jacket. The core is selected to have (1) a higher refractive index than the core and the cladding and (2) a relatively high negative temperature coefficient of refractive index. A light beam capable of establishing substantially single-mode propagation in the core is launched into an end thereof at an angle to the axis. The angle is increased to effect the onset of light fraction from the core into the cladding. The value of the launch angle corresponding to the onset is determined and then used to establish the refractive index of the core corresponding to the onset angle. The maximum temperature prevailing along the fiber then is determined from the (1) refractive index so determined and (2) the temperature coefficient of refractive index for the core. The invention is based on the finding that the launch angle corresponding to the onset of refraction into the cladding is uniquely determined by the maximum value of the ratio of the core refractive index to the cladding refractive index, which maximum occurs at the hottest point along the fiber.

Method and apparatus for determining peak temperature along an optical fiber

DOEpatents

Fox, Richard J.

1985-01-01

The invention relates to a new method and new apparatus for determining the hottest temperature or the coldest temperature prevailing along the length of an optical-fiber light guide. The invention is conducted with an optical fiber capable of supporting multidiode propagation of light and comprising a core, a cladding, and a jacket. The core is selected to have (1) a higher refractive index than the core and the cladding and (2) a relatively high negative temperature coefficient of refractive index. A light beam capable of establishing substantially single-mode propagation in the core is launched into an end thereof at an angle to the axis. The angle is increased to effect the onset of light refraction from the core into the cladding. The value of the launch angle corresponding to the onset is determined and then used to establish the refractive index of the core corresponding to the onset angle. The maximum temperature prevailing along the fiber then is determined from the (1) refractive index so determined and (2) the temperature coefficient of refractive index for the core. The invention is based on the finding that the launch angle corresponding to the onset of refraction into the cladding is uniquely determined by the maximum value of the ratio of the core refractive index to the cladding refractive index, which maximum occurs at the hottest point along the fiber.

20 CFR Appendix 2 to Part 220 - Medical-Vocational Guidelines

Code of Federal Regulations, 2012 CFR

2012-04-01

... medically determinable impairment(s). 203.00Maximum sustained work capability limited to medium work as a... his or her maximum sustained work capability for sedentary, light, medium, heavy, or very heavy work... at the various functional levels (sedentary, light, medium, heavy, and very heavy) as supported by...

20 CFR Appendix 2 to Part 220 - Medical-Vocational Guidelines

Code of Federal Regulations, 2013 CFR

2013-04-01

... medically determinable impairment(s). 203.00Maximum sustained work capability limited to medium work as a... his or her maximum sustained work capability for sedentary, light, medium, heavy, or very heavy work... at the various functional levels (sedentary, light, medium, heavy, and very heavy) as supported by...

20 CFR Appendix 2 to Part 220 - Medical-Vocational Guidelines

Code of Federal Regulations, 2014 CFR

2014-04-01

... medically determinable impairment(s). 203.00Maximum sustained work capability limited to medium work as a... his or her maximum sustained work capability for sedentary, light, medium, heavy, or very heavy work... at the various functional levels (sedentary, light, medium, heavy, and very heavy) as supported by...

20 CFR Appendix 2 to Part 220 - Medical-Vocational Guidelines

Code of Federal Regulations, 2011 CFR

2011-04-01

... medically determinable impairment(s). 203.00Maximum sustained work capability limited to medium work as a... his or her maximum sustained work capability for sedentary, light, medium, heavy, or very heavy work... at the various functional levels (sedentary, light, medium, heavy, and very heavy) as supported by...

49 CFR 236.701 - Application, brake; full service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... a split reduction in brake pipe pressure at a service rate until maximum brake cylinder pressure is developed. As applied to an automatic or electro-pneumatic brake with speed governor control, an application other than emergency which develops the maximum brake cylinder pressure, as determined by the design of...

The maximum depth of shower with E sub 0 larger than 10(17) eV on average characteristics of EAS different components

NASA Technical Reports Server (NTRS)

Glushkov, A. V.; Efimov, N. N.; Makarov, I. T.; Pravdin, M. I.; Dedenko, L. G.

1985-01-01

The extensive air shower (EAS) development model independent method of the determination of a maximum depth of shower (X sub m) is considered. X sub m values obtained on various EAS parameters are in a good agreement.

20 CFR Appendix 2 to Part 220 - Medical-Vocational Guidelines

Code of Federal Regulations, 2010 CFR

2010-04-01

... medically determinable impairment(s). 203.00Maximum sustained work capability limited to medium work as a... his or her maximum sustained work capability for sedentary, light, medium, heavy, or very heavy work... at the various functional levels (sedentary, light, medium, heavy, and very heavy) as supported by...

25 CFR 273.4 - Policy of maximum Indian participation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 25 Indians 1 2014-04-01 2014-04-01 false Policy of maximum Indian participation. 273.4 Section 273.4 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR INDIAN SELF-DETERMINATION AND EDUCATION ASSISTANCE ACT PROGRAM EDUCATION CONTRACTS UNDER JOHNSON-O'MALLEY ACT General Provisions § 273.4...

14 CFR 23.1563 - Airspeed placards.

Code of Federal Regulations, 2012 CFR

2012-01-01

... than 6,000 pounds maximum weight, and turbine engine-powered airplanes, the maximum value of the minimum control speed, VMC (one-engine-inoperative) determined under § 23.149(b). [Amdt. 23-7, 34 FR 13097... lighted area such as the landing gear control and the airspeed indicator has features such as low speed...

Maximum Oxygen Uptake Determination in Insulin-Dependent Diabetes Mellitus.

ERIC Educational Resources Information Center

Fremion, Amy S.; And Others

1987-01-01

A study of 10 children with insulin-dependent diabetes mellitus performing a maximum-effort cycling test indicated blood glucose levels did not change appreciably during test, while maximal oxygen uptake was substandard for their age groups. Findings suggest patients in fair to poor metabolic control can tolerate stress testing without…

Evaluation of performance and maximum length of continuous decks in bridges : part 1.

DOT National Transportation Integrated Search

2011-06-01

The purpose of this research was to evaluate the performance history of continuous bridge decks in the State of Georgia, to determine why the current design detail works, to recommend a new design detail, and to recommend the maximum and/or optimum l...

Patient positioning using artificial intelligence neural networks, trained magnetic field sensors and magnetic implants.

PubMed

Lennernäs, B; Edgren, M; Nilsson, S

1999-01-01

The purpose of this study was to evaluate the precision of a sensor and to ascertain the maximum distance between the sensor and the magnet, in a magnetic positioning system for external beam radiotherapy using a trained artificial intelligence neural network for position determination. Magnetic positioning for radiotherapy, previously described by Lennernäs and Nilsson, is a functional technique, but it is time consuming. The sensors are large and the distance between the sensor and the magnetic implant is limited to short distances. This paper presents a new technique for positioning, using an artificial intelligence neural network, which was trained to position the magnetic implant with at least 0.5 mm resolution in X and Y dimensions. The possibility of using the system for determination in the Z dimension, that is the distance between the magnet and the sensor, was also investigated. After training, this system positioned the magnet with a mean error of maximum 0.15 mm in all dimensions and up to 13 mm from the sensor. Of 400 test positions, 8 determinations had an error larger than 0.5 mm, maximum 0.55 mm. A position was determined in approximately 0.01 s.

Comparative Flight and Full-Scale Wind-Tunnel Measurements of the Maximum Lift of an Airplane

NASA Technical Reports Server (NTRS)

Silverstein, Abe; Katzoff, S; Hootman, James A

1938-01-01

Determinations of the power-off maximum lift of a Fairchild 22 airplane were made in the NACA full-scale wind tunnel and in flight. The results from the two types of test were in satisfactory agreement. It was found that, when the airplane was rotated positively in pitch through the angle of stall at rates of the order of 0.1 degree per second, the maximum lift coefficient was considerably higher than that obtained in the standard tests, in which the forces are measured with the angles of attack fixed. Scale effect on the maximum lift coefficient was also investigated.

In-flight calibration and performance evaluation of the fixed head star trackers for the solar maximum mission

NASA Technical Reports Server (NTRS)

Thompson, R. H.; Gambardella, P. J.

1980-01-01

The Solar Maximum Mission (SMM) spacecraft provides an excellent opportunity for evaluating attitude determination accuracies achievable with tracking instruments such as fixed head star trackers (FHSTs). As a part of its payload, SMM carries a highly accurate fine pointing Sun sensor (FPSS). The EPSS provides an independent check of the pitch and yaw parameters computed from observations of stars in the FHST field of view. A method to determine the alignment of the FHSTs relative to the FPSS using spacecraft data is applied. Two methods that were used to determine distortions in the 8 degree by 8 degree field of view of the FHSTs using spacecraft data are also presented. The attitude determination accuracy performance of the in flight calibrated FHSTs is evaluated.

Countermovement depth - a variable which clarifies the relationship between the maximum power output and height of a vertical jump.

PubMed

Gajewski, Jan; Michalski, Radosław; Buśko, Krzysztof; Mazur-Różycka, Joanna; Staniak, Zbigniew

2018-01-01

The aim of this study was to identify the determinants of peak power achieved during vertical jumps in order to clarify relationship between the height of jump and the ability to exert maximum power. One hundred young (16.8±1.8 years) sportsmen participated in the study (body height 1.861 ± 0.109 m, body weight 80.3 ± 9.2 kg). Each participant performed three jump tests: countermovement jump (CMJ), akimbo countermovement jump (ACMJ), and spike jump (SPJ). A force plate was used to measure ground reaction force and to determine peak power output. The following explanatory variables were included in the model: jump height, body mass, and the lowering of the centre of mass before launch (countermovement depth). A model was created using multiple regression analysis and allometric scaling. The model was used to calculate the expected power value for each participant, which correlated strongly with real values. The value of the coefficient of determination R2 equalled 0.89, 0.90 and 0.98, respectively, for the CMJ, ACMJ, and SPJ jumps. The countermovement depth proved to be a variable strongly affecting the maximum power of jump. If the countermovement depth remains constant, the relative peak power is a simple function of jump height. The results suggest that the jump height of an individual is an exact indicator of their ability to produce maximum power. The presented model has a potential to be utilized under field condition for estimating the maximum power output of vertical jumps.

Kinematics and Kinetics of Taekwon-do Side Kick

PubMed Central

Wąsik, Jacek

2011-01-01

The aim of the paper is to present an analysis of the influence of selected kinematic factors on the side kick technique. This issue is especially important in the traditional version of taekwon-do, in which a single strike may reveal the winner. Six taekwon-do (International Taekwon-do Federation) athletes were asked to participate in this case study. Generally accepted criteria of sports technique biomechanical analysis were adhered to. The athletes executed a side kick three times (in Taekwon-do terminology referred to as yop chagi) in a way which they use the kick in board breaking. The obtained data were used to determine the mean velocity changes in the function of relative extension length of the kicking leg. The maximum knee and foot velocities in the Cartesian coordinate system were determined. The leg lifting time and the duration of kick execution as well as the maximum force which the standing foot exerted on the ground were also determined. On the basis of the obtained values, mean values and standard deviations were calculated. The correlation dependence (r=0.72) shows that greater knee velocity affects the velocity which the foot develops as well as the fact that the total time of kick execution depends on the velocity which the knee (r = −0.59) and the foot (r = − 0.86) develop in the leg lifting phase. The average maximum speed was obtained at the length of the leg equal to 82% of the maximum length of the fully extended leg. This length can be considered the optimum value for achieving the maximum dynamics of the kick. PMID:23486086

Fluoride in the drinking water of Nagaur tehsil of Nagaur District, Rajasthan, India.

PubMed

Arif, M; Hussain, I; Hussain, J; Sharma, S; Kumar, S

2012-06-01

Fluoride concentration of groundwater samples from 100 villages of Nagaur tehsil was determined, 85 villages were found to have fluoride concentration more than 1.5 mg/L. The maximum fluoride concentration was recorded 6.6 mg/L in groundwater of Singhani village, while the minimum was recorded in Kurchhi village. As per the desirable and maximum permissible limit for fluoride in drinking water, determined by World Health Organization, the groundwater of about 85 villages of the studied sites is unfit for drinking purpose.

Spark-Timing Control Based on Correlation of Maximum-Economy Spark Timing, Flame-front Travel, and Cylinder-Pressure Rise

NASA Technical Reports Server (NTRS)

Cook, Harvey A; Heinicke, Orville H; Haynie, William H

1947-01-01

An investigation was conducted on a full-scale air-cooled cylinder in order to establish an effective means of maintaining maximum-economy spark timing with varying engine operating conditions. Variable fuel-air-ratio runs were conducted in which relations were determined between the spark travel, and cylinder-pressure rise. An instrument for controlling spark timing was developed that automatically maintained maximum-economy spark timing with varying engine operating conditions. The instrument also indicated the occurrence of preignition.

Effect on interference fits on roller bearing fatigue life

NASA Technical Reports Server (NTRS)

Coe, H. H.; Zaretsky, E. V.

1986-01-01

An analysis was performed to determine the effects of inner-ring speed and press fits on roller bearing fatigue life. The effects of the resultant hoop and radial stresses on the principal stresses were considered. The maximum shear stresses below the Hertzian contact were determined for different conditions of inner-ring speed and load, and were applied to a conventional roller bearing life analysis. The effect of mean stress was determined using Goodman diagram approach. Hoop stresses caused by press fits and centrifugal force can reduce bearing life by as much as 90 percent. Use of a Goodman diagram predicts life reductions of 20 to 30 percent. The depth of the maximum shear stress remains virtually unchanged.

Effect of interference fits on roller bearing fatigue life

NASA Technical Reports Server (NTRS)

Coe, Harold H.; Zaretsky, Erwin V.

1987-01-01

An analysis was performed to determine the effects of inner-ring speed and press fits on roller bearing fatigue life. The effects of the resultant hoop and radial stresses on the principal stresses were considered. The maximum shear stresses below the Hertzian contact were determined for different conditions of inner-ring speed and load, and were applied to a conventional roller bearing life analysis. The effect of mean stress was determined using Goodman diagram approach. Hoop stresses caused by press fits and centrifugal force can reduce bearing life by as much as 90 percent. Use of a Goodman diagram predicts life reduction of 20 to 30 percent. The depth of the maximum shear stress remains virtually unchanged.

Migration rates and formation injectivity to determine containment time scales of sequestered carbon dioxide

USGS Publications Warehouse

Burke, Lauri

2012-01-01

Additionally, this research establishes a methodology to calculate the injectivity of a target formation. Because injectivity describes the pressure increase due to the introduction of fluids into a formation, the relevant application of injectivity is to determine the pressure increase, due to an injection volume and flow rate, that will induce fractures in the reservoir rocks. This quantity is defined mathematically as the maximum pressure differential between the hydrostatic gradient and the fracture gradient of the target formation. Injectivity is mathematically related to the maximum pressure differential of the formation, and can be used to determine the upper limit for the pressure increase that an injection target can withstand before fracturing.

40 CFR 63.55 - Maximum achievable control technology (MACT) determinations for affected sources subject to case...

Code of Federal Regulations, 2010 CFR

2010-07-01

... (MACT) determinations for affected sources subject to case-by-case determination of equivalent emission... sources subject to case-by-case determination of equivalent emission limitations. (a) Requirements for... hazardous air pollutant emissions limitations equivalent to the limitations that would apply if an emission...

The effect of uncontrolled moment and short-term, repeated passive stretching on maximum ankle joint dorsiflexion angle.

PubMed

Gatt, Alfred; Chockalingam, Nachiappan

2012-06-01

Trials investigating ankle joint measurement normally apply a known moment. Maximum ankle angle is affected by foot posture and stretching characteristics of the calf muscles. To investigate whether consistent maximum ankle angles could be achieved without applying a constant moment to all subjects, and whether short, repetitive stretching of the calf muscle tendon unit would produce a difference in the maximum ankle angle. Passive dorsiflexion in 14 healthy participants was captured using an optoelectronic motion analysis system, with the foot placed in 3 postures. The maximum ankle angles for both the neutral and supinated positions did not differ significantly. In general, the majority of subjects (92.8%) showed no increase in the maximum ankle dorsiflexion angle following repetitive brief passive stretching. Only one subject exhibited a significant increase in maximum ankle angle at the neutral position. Since the range of motion of the ankle joint is clearly determined by other physical factors, the maximum ankle dorsiflexion angle can be assessed at both neutral and supinated positions without moment being controlled. Copyright © 2011 Elsevier Ltd. All rights reserved.

Average diurnal variation of summer lightning over the Florida peninsula

NASA Technical Reports Server (NTRS)

Maier, L. M.; Krider, E. P.; Maier, M. W.

1984-01-01

Data derived from a large network of electric field mills are used to determine the average diurnal variation of lightning in a Florida seacoast environment. The variation at the NASA Kennedy Space Center and the Cape Canaveral Air Force Station area is compared with standard weather observations of thunder, and the variation of all discharges in this area is compared with the statistics of cloud-to-ground flashes over most of the South Florida peninsula and offshore waters. The results show average diurnal variations that are consistent with statistics of thunder start times and the times of maximum thunder frequency, but that the actual lightning tends to stop one to two hours before the recorded thunder. The variation is also consistent with previous determinations of the times of maximum rainfall and maximum rainfall rate.

Performance of Chevron-notch short bar specimen in determining the fracture toughness of silicon nitride and aluminum oxide

NASA Technical Reports Server (NTRS)

Munz, D.; Bubsey, R. T.; Shannon, J. L., Jr.

1980-01-01

Ease of preparation and testing are advantages unique to the chevron-notch specimen used for the determination of the plane strain fracture toughness of extremely brittle materials. During testing, a crack develops at the notch tip and extends stably as the load is increased. For a given specimen and notch configuration, maximum load always occurs at the same relative crack length independent of the material. Fracture toughness is determined from the maximum load with no need for crack length measurement. Chevron notch acuity is relatively unimportant since a crack is produced during specimen loading. In this paper, the authors use their previously determined stress intensity factor relationship for the chevron-notch short bar specimen to examine the performance of that specimen in determining the plane strain fracture toughness of silicon nitride and aluminum oxide.

Spacecraft maximum allowable concentrations for selected airborne contaminants, volume 1

NASA Technical Reports Server (NTRS)

1994-01-01

As part of its efforts to promote safe conditions aboard spacecraft, NASA requested the National Research Council (NRC) to develop guidelines for establishing spacecraft maximum allowable concentrations (SMAC's) for contaminants, and to review SMAC's for various spacecraft contaminants to determine whether NASA's recommended exposure limits are consistent with the guidelines recommended by the subcommittee. In response to NASA's request, the NRC organized the Subcommittee on Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants within the Committee on Toxicology (COT). In the first phase of its work, the subcommittee developed the criteria and methods for preparing SMAC's for spacecraft contaminants. The subcommittee's report, entitled Guidelines for Developing Spacecraft Maximum Allowable Concentrations for Space Station Contaminants, was published in 1992. The executive summary of that report is reprinted as Appendix A of this volume. In the second phase of the study, the Subcommittee on Spacecraft Maximum Allowable Concentrations reviewed reports prepared by NASA scientists and contractors recommending SMAC's for 35 spacecraft contaminants. The subcommittee sought to determine whether the SMAC reports were consistent with the 1992 guidelines. Appendix B of this volume contains the first 11 SMAC reports that have been reviewed for their application of the guidelines developed in the first phase of this activity and approved by the subcommittee.

Altitude-Test-Chamber Investigation of a Solar Afterburner on the 24C Engine I - Operational Characteristics and Altitude Limits

NASA Technical Reports Server (NTRS)

1948-01-01

An altitude-test-chamber investigation was conducted to determine the operational characteristics and altitude blow-out limits of a Solar afterburner in a 24C engine. At rated engine speed and maximum permissible turbine-discharge temperature, the altitude limit as determined by combustion blow-out occurred as a band of unstable operation of about 8000 feet altitude in width with maximum altitude limits from 32,000 feet at a Mach number of 0.3 to about 42,000 feet at a Mach number of 1.0. The maximum fuel-air ratio of the afterburner, as limited by maximum permissible turbine-discharge gas temperatures at rated engine speed, varied between 0.0295 and 0.0380 over a range of flight Mach numbers from 0.25 to 1.0 and at altitudes of 20,000 and 30,000 feet. Over this range of operating conditions, the fuel-air ratio at which lean blow-out occurred was from 10 to 19 percent below these maximum fuel-air ratios. Combustion was very smooth and uniform during operation; however, ignition of the burner was very difficult throughout the investigation. A failure of the flame holder after 12 hours and 15 minutes of afterburner operation resulted in termination of the investigation.

Sea ice - atmosphere interaction: Application of multispectral satellite data in polar surface energy flux estimates

NASA Technical Reports Server (NTRS)

Steffen, Konrad; Schweiger, A.; Maslanik, J.; Key, J.; Haefliger, M.; Weaver, R.

1991-01-01

In the past six months, work has continued on energy flux sensitivity studies, ice surface temperature retrievals, corrections to Advanced Very High Resolution Radiometer (AVHRR) thermal infrared data, modelling of cloud fraction retrievals, and radiation climatologies. We tentatively conclude that the SSM/I may not provide accurate enough estimates of ice concentration and type to improve our shorter term energy flux estimates. SSM/I derived parameters may still be applicable in longer term climatological flux characterizations. We hold promise for a system coupling observation to a ice deformation model. Such a model may provide information on ice distribution which can be used in energy flux calculations. Considerable variation was found in modelled energy flux estimates when bulk transfer coefficients are modulated by lead fetch. It is still unclear what the optimum formulation is and this will be the subject of further work. Data sets for ice surface temperature retrievals were assembled and preliminary data analysis was started. Finally, construction of a conceptual framework for further modelling of the Arctic radiation flux climatology was started.

Three-Year-Olds’ Understanding of the Consequences of Joint Commitments

PubMed Central

Gräfenhain, Maria; Carpenter, Malinda; Tomasello, Michael

2013-01-01

Here we investigate the extent of children’s understanding of the joint commitments inherent in joint activities. Three-year-old children either made a joint commitment to assemble a puzzle with a puppet partner, or else the child and puppet each assembled their own puzzle. Afterwards, children who had made the joint commitment were more likely to stop and wait for their partner on their way to fetch something, more likely to spontaneously help their partner when needed, and more likely to take over their partner’s role when necessary. There was no clear difference in children’s tendency to tattle on their partner’s cheating behavior or their tendency to distribute rewards equally at the end. It thus appears that by 3 years of age making a joint commitment to act together with others is beginning to engender in children a “we”-intentionality which holds across at least most of the process of the joint activity until the shared goal is achieved, and which withstands at least some of the perturbations to the joint activity children experience. PMID:24023805

Family planning and development.

PubMed

Barnett, B

1994-08-01

Women in many countries are of only very low social standing with limited control over resources and the circumstances in which they live. Levels of infant and child mortality are also very high in many areas of the world. In the attempt to rear progeny which survive into adulthood, these women bear many children. Children are a source of labor and power who can gather fuel, cook, fetch water, perform other chores, and ultimately provide security for elderly parents. Were rates of infant and child mortality to decline and women to have more opportunity to earn livelihoods on their own, however, they would not need to bear quite so many children. Levels of fertility would decline in keeping with the goals of family planning programs around the world. The direct relationship between women's poverty, women's lack of autonomy, and high fertility requires one to address the complete range of women's reproductive needs instead of focusing narrowly upon the distribution of contraceptives. To that end, some family planning and economic development programs have merged to provide contraceptive services which are linked with broader efforts to improve health, education, and employment. Program experiences are discussed.

RSAT 2015: Regulatory Sequence Analysis Tools.

PubMed

Medina-Rivera, Alejandra; Defrance, Matthieu; Sand, Olivier; Herrmann, Carl; Castro-Mondragon, Jaime A; Delerce, Jeremy; Jaeger, Sébastien; Blanchet, Christophe; Vincens, Pierre; Caron, Christophe; Staines, Daniel M; Contreras-Moreira, Bruno; Artufel, Marie; Charbonnier-Khamvongsa, Lucie; Hernandez, Céline; Thieffry, Denis; Thomas-Chollier, Morgane; van Helden, Jacques

2015-07-01

RSAT (Regulatory Sequence Analysis Tools) is a modular software suite for the analysis of cis-regulatory elements in genome sequences. Its main applications are (i) motif discovery, appropriate to genome-wide data sets like ChIP-seq, (ii) transcription factor binding motif analysis (quality assessment, comparisons and clustering), (iii) comparative genomics and (iv) analysis of regulatory variations. Nine new programs have been added to the 43 described in the 2011 NAR Web Software Issue, including a tool to extract sequences from a list of coordinates (fetch-sequences from UCSC), novel programs dedicated to the analysis of regulatory variants from GWAS or population genomics (retrieve-variation-seq and variation-scan), a program to cluster motifs and visualize the similarities as trees (matrix-clustering). To deal with the drastic increase of sequenced genomes, RSAT public sites have been reorganized into taxon-specific servers. The suite is well-documented with tutorials and published protocols. The software suite is available through Web sites, SOAP/WSDL Web services, virtual machines and stand-alone programs at http://www.rsat.eu/. © The Author(s) 2015. Published by Oxford University Press on behalf of Nucleic Acids Research.

Hurricanes, coral reefs and rainforests: resistance, ruin and recovery in the Caribbean

USGS Publications Warehouse

Lugo, Ariel E.; Rogers, Caroline S.; Nixon, Scott W.

2000-01-01

The coexistence of hurricanes, coral reefs, and rainforests in the Caribbean demonstrates that highly structured ecosystems with great diversity can flourish in spite of recurring exposure to intense destructive energy. Coral reefs develop in response to wave energy and resist hurricanes largely by virtue of their structural strength. Limited fetch also protects some reefs from fully developed hurricane waves. While storms may produce dramatic local reef damage, they appear to have little impact on the ability of coral reefs to provide food or habitat for fish and other animals. Rainforests experience an enormous increase in wind energy during hurricanes with dramatic structural changes in the vegetation. The resulting changes in forest microclimate are larger than those on reefs and the loss of fruit, leaves, cover, and microclimate has a great impact on animal populations. Recovery of many aspects of rainforest structure and function is rapid, though there may be long-term changes in species composition. While resistance and repair have maintained reefs and rainforests in the past, human impacts may threaten their ability to survive.

Spatio-Temporal Pattern Analysis for Regional Climate Change Using Mathematical Morphology

NASA Astrophysics Data System (ADS)

Das, M.; Ghosh, S. K.

2015-07-01

Of late, significant changes in climate with their grave consequences have posed great challenges on humankind. Thus, the detection and assessment of climatic changes on a regional scale is gaining importance, since it helps to adopt adequate mitigation and adaptation measures. In this paper, we have presented a novel approach for detecting spatio-temporal pattern of regional climate change by exploiting the theory of mathematical morphology. At first, the various climatic zones in the region have been identified by using multifractal cross-correlation analysis (MF-DXA) of different climate variables of interest. Then, the directional granulometry with four different structuring elements has been studied to detect the temporal changes in spatial distribution of the identified climatic zones in the region and further insights have been drawn with respect to morphological uncertainty index and Hurst exponent. The approach has been evaluated with the daily time series data of land surface temperature (LST) and precipitation rate, collected from Microsoft Research - Fetch Climate Explorer, to analyze the spatio-temporal climatic pattern-change in the Eastern and North-Eastern regions of India throughout four quarters of the 20th century.

AmeriFlux Measurement Component (AMC) Handbook

DOE Office of Scientific and Technical Information (OSTI.GOV)

Reichl, K.; Biraud, S. C.

An AMC system was installed at the Atmospheric Radiation Measurement (ARM) Climate Research Facility’s North Slope Alaska (NSA) Barrow site, also known as NSA C1 at the ARM Data Archive, in August 2012. A second AMC system was installed at the third ARM Mobile Facility deployment at Oliktok Point, also known as NSA M1. This in situ system consists of 12 combination soil temperature and volumetric water content (VWC) reflectometers and one set of upwelling and downwelling PAR sensors, all deployed within the fetch of the Eddy Correlation Flux Measurement System. Soil temperature and VWC sensors placed at two depthsmore » (10 and 30 cm below the vegetation layer) at six locations (or microsites) allow soil property inhomogeneity to be monitored across a landscape. The soil VWC and temperature sensors used at NSA C1 are the Campbell Scientific CS650L and the sensors at NSA M1 use the Campbell Scientific CS655. The two sensors are nearly identical in function, and vendor specifications are based on the CS650 unless otherwise stated.« less

Fast grasping of unknown objects using cylinder searching on a single point cloud

NASA Astrophysics Data System (ADS)

Lei, Qujiang; Wisse, Martijn

2017-03-01

Grasping of unknown objects with neither appearance data nor object models given in advance is very important for robots that work in an unfamiliar environment. The goal of this paper is to quickly synthesize an executable grasp for one unknown object by using cylinder searching on a single point cloud. Specifically, a 3D camera is first used to obtain a partial point cloud of the target unknown object. An original method is then employed to do post treatment on the partial point cloud to minimize the uncertainty which may lead to grasp failure. In order to accelerate the grasp searching, surface normal of the target object is then used to constrain the synthetization of the cylinder grasp candidates. Operability analysis is then used to select out all executable grasp candidates followed by force balance optimization to choose the most reliable grasp as the final grasp execution. In order to verify the effectiveness of our algorithm, Simulations on a Universal Robot arm UR5 and an under-actuated Lacquey Fetch gripper are used to examine the performance of this algorithm, and successful results are obtained.

Characterising terrestrial influences on Antarctic air masses using Radon-222 measurements at King George Island

NASA Astrophysics Data System (ADS)

Chambers, S. D.; Hong, S.-B.; Williams, A. G.; Crawford, J.; Griffiths, A. D.; Park, S.-J.

2014-09-01

We report on one year of high-precision direct hourly radon observations at King Sejong Station (King George Island) beginning in February 2013. Findings are compared with historic and ongoing radon measurements from other Antarctic sites. Monthly median concentrations reduced from 72 mBq m-3 in late-summer to 44 mBq m-3 in late winter and early spring. Monthly 10th percentiles, ranging from 29 to 49 mBq m-3, were typical of oceanic baseline values. Diurnal cycles were rarely evident and local influences were minor, consistent with regional radon flux estimates one tenth of the global average for ice-free land. The predominant fetch region for terrestrially influenced air masses was South America (47-53° S), with minor influences also attributed to aged Australian air masses and local sources. Plume dilution factors of 2.8-4.0 were estimated for the most terrestrially influenced (South American) air masses, and a seasonal cycle in terrestrial influence on tropospheric air descending at the pole was identified and characterised.

Characterising terrestrial influences on Antarctic air masses using radon-222 measurements at King George Island

NASA Astrophysics Data System (ADS)

Chambers, S. D.; Hong, S.-B.; Williams, A. G.; Crawford, J.; Griffiths, A. D.; Park, S.-J.

2014-05-01

We report on one year of high precision direct hourly radon observations at King Sejong Station (King George Island) beginning in February 2013. Findings are compared with historic and ongoing radon measurements from other Antarctic sites. Monthly median concentrations reduced from 72 mBq m-3 in late summer to 44 mBq m-3 in late-winter and early-spring. Monthly 10th percentiles, ranging from 29 to 49 mBq m-3, were typical of oceanic baseline values. Diurnal cycles were rarely evident and local influences were minor, consistent with regional radon flux estimates one tenth of the global average for ice-free land. The predominant fetch region for terrestrially influenced air masses was South America (47-53° S), with minor influences also attributed to aged Australian air masses and local sources. Plume dilution factors of 2.8-4.0 were estimated for the most terrestrially influenced (South American) air masses, and a seasonal cycle in terrestrial influence on tropospheric air descending at the pole was identified and characterised.

A unified approach for development of Urdu Corpus for OCR and demographic purpose

NASA Astrophysics Data System (ADS)

Choudhary, Prakash; Nain, Neeta; Ahmed, Mushtaq

2015-02-01

This paper presents a methodology for the development of an Urdu handwritten text image Corpus and application of Corpus linguistics in the field of OCR and information retrieval from handwritten document. Compared to other language scripts, Urdu script is little bit complicated for data entry. To enter a single character it requires a combination of multiple keys entry. Here, a mixed approach is proposed and demonstrated for building Urdu Corpus for OCR and Demographic data collection. Demographic part of database could be used to train a system to fetch the data automatically, which will be helpful to simplify existing manual data-processing task involved in the field of data collection such as input forms like Passport, Ration Card, Voting Card, AADHAR, Driving licence, Indian Railway Reservation, Census data etc. This would increase the participation of Urdu language community in understanding and taking benefit of the Government schemes. To make availability and applicability of database in a vast area of corpus linguistics, we propose a methodology for data collection, mark-up, digital transcription, and XML metadata information for benchmarking.

An FPGA computing demo core for space charge simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Jinyuan; Huang, Yifei; /Fermilab

2009-01-01

In accelerator physics, space charge simulation requires large amount of computing power. In a particle system, each calculation requires time/resource consuming operations such as multiplications, divisions, and square roots. Because of the flexibility of field programmable gate arrays (FPGAs), we implemented this task with efficient use of the available computing resources and completely eliminated non-calculating operations that are indispensable in regular micro-processors (e.g. instruction fetch, instruction decoding, etc.). We designed and tested a 16-bit demo core for computing Coulomb's force in an Altera Cyclone II FPGA device. To save resources, the inverse square-root cube operation in our design is computedmore » using a memory look-up table addressed with nine to ten most significant non-zero bits. At 200 MHz internal clock, our demo core reaches a throughput of 200 M pairs/s/core, faster than a typical 2 GHz micro-processor by about a factor of 10. Temperature and power consumption of FPGAs were also lower than those of micro-processors. Fast and convenient, FPGAs can serve as alternatives to time-consuming micro-processors for space charge simulation.« less

An AES chip with DPA resistance using hardware-based random order execution

NASA Astrophysics Data System (ADS)

Bo, Yu; Xiangyu, Li; Cong, Chen; Yihe, Sun; Liji, Wu; Xiangmin, Zhang

2012-06-01

This paper presents an AES (advanced encryption standard) chip that combats differential power analysis (DPA) side-channel attack through hardware-based random order execution. Both decryption and encryption procedures of an AES are implemented on the chip. A fine-grained dataflow architecture is proposed, which dynamically exploits intrinsic byte-level independence in the algorithm. A novel circuit called an HMF (Hold-Match-Fetch) unit is proposed for random control, which randomly sets execution orders for concurrent operations. The AES chip was manufactured in SMIC 0.18 μm technology. The average energy for encrypting one group of plain texts (128 bits secrete keys) is 19 nJ. The core area is 0.43 mm2. A sophisticated experimental setup was built to test the DPA resistance. Measurement-based experimental results show that one byte of a secret key cannot be disclosed from our chip under random mode after 64000 power traces were used in the DPA attack. Compared with the corresponding fixed order execution, the hardware based random order execution is improved by at least 21 times the DPA resistance.

Stream Processors

NASA Astrophysics Data System (ADS)

Erez, Mattan; Dally, William J.

Stream processors, like other multi core architectures partition their functional units and storage into multiple processing elements. In contrast to typical architectures, which contain symmetric general-purpose cores and a cache hierarchy, stream processors have a significantly leaner design. Stream processors are specifically designed for the stream execution model, in which applications have large amounts of explicit parallel computation, structured and predictable control, and memory accesses that can be performed at a coarse granularity. Applications in the streaming model are expressed in a gather-compute-scatter form, yielding programs with explicit control over transferring data to and from on-chip memory. Relying on these characteristics, which are common to many media processing and scientific computing applications, stream architectures redefine the boundary between software and hardware responsibilities with software bearing much of the complexity required to manage concurrency, locality, and latency tolerance. Thus, stream processors have minimal control consisting of fetching medium- and coarse-grained instructions and executing them directly on the many ALUs. Moreover, the on-chip storage hierarchy of stream processors is under explicit software control, as is all communication, eliminating the need for complex reactive hardware mechanisms.

Karl Pearson and eugenics: personal opinions and scientific rigor.

PubMed

Delzell, Darcie A P; Poliak, Cathy D

2013-09-01

The influence of personal opinions and biases on scientific conclusions is a threat to the advancement of knowledge. Expertise and experience does not render one immune to this temptation. In this work, one of the founding fathers of statistics, Karl Pearson, is used as an illustration of how even the most talented among us can produce misleading results when inferences are made without caution or reference to potential bias and other analysis limitations. A study performed by Pearson on British Jewish schoolchildren is examined in light of ethical and professional statistical practice. The methodology used and inferences made by Pearson and his coauthor are sometimes questionable and offer insight into how Pearson's support of eugenics and his own British nationalism could have potentially influenced his often careless and far-fetched inferences. A short background into Pearson's work and beliefs is provided, along with an in-depth examination of the authors' overall experimental design and statistical practices. In addition, portions of the study regarding intelligence and tuberculosis are discussed in more detail, along with historical reactions to their work.

Live Imaging of Centriole Dynamics by Fluorescently Tagged Proteins in Starfish Oocyte Meiosis.

PubMed

Borrego-Pinto, Joana; Somogyi, Kálmán; Lénárt, Péter

2016-01-01

High throughput DNA sequencing, the decreasing costs of DNA synthesis, and universal techniques for genetic manipulation have made it much easier and quicker to establish molecular tools for any organism than it has been 5 years ago. This opens a great opportunity for reviving "nonconventional" model organisms, which are particularly suited to study a specific biological process and many of which have already been established before the era of molecular biology. By taking advantage of transcriptomics, in particular, these systems can now be easily turned into full fetched models for molecular cell biology.As an example, here we describe how we established molecular tools in the starfish Patiria miniata, which has been a popular model for cell and developmental biology due to the synchronous and rapid development, transparency, and easy handling of oocytes, eggs, and embryos. Here, we detail how we used a de novo assembled transcriptome to produce molecular markers and established conditions for live imaging to investigate the molecular mechanisms underlying centriole elimination-a poorly understood process essential for sexual reproduction of animal species.

MATISSE-v1.5 and MATISSE-v2.0: new developments and comparison with MIRAMER measurements

NASA Astrophysics Data System (ADS)

Simoneau, Pierre; Caillault, Karine; Fauqueux, Sandrine; Huet, Thierry; Labarre, Luc; Malherbe, Claire; Rosier, Bernard

2009-05-01

MATISSE is a background scene generator developed for the computation of natural background spectral radiance images and useful atmospheric radiatives quantities (radiance and transmission along a line of sight, local illumination, solar irradiance ...). The spectral bandwidth ranges from 0.4 to 14 μm. Natural backgrounds include atmosphere (taking into account spatial variability), low and high altitude clouds, sea and land. The current version MATISSE-v1.5 can be run on SUN and IBM workstations as well as on PC under Windows and Linux environment. An IHM developed under Java environment is also implemented. MATISSE-v2.0 recovers all the MATISSE-v1.5 functionalities, and includes a new sea surface radiance model depending on wind speed, wind direction and the fetch value. The release of this new version in planned for April 2009. This paper gives a description of MATISSE-v1.5 and MATISSE-v2.0 and shows preliminary comparison results between generated images and measured images during the MIRAMER campaign, which hold in May 2008 in the Mediterranean Sea.

Joint-action coordination in transferring objects

PubMed Central

Bosga, Jurjen; Hulstijn, Majken; Miedl, Stephan

2007-01-01

Here we report a study of joint-action coordination in transferring objects. Fourteen dyads were asked to repeatedly reposition a cylinder in a shared workspace without using dialogue. Variations in task constraints concerned the size of the two target regions in which the cylinder had to be (re)positioned and the size and weight of the transferred cylinder. Movements of the wrist, index finger and thumb of both actors were recorded by means of a 3D motion-tracking system. Data analyses focused on the interpersonal transfer of lifting-height and movement-speed variations. Whereas the analyses of variance did not reveal any interpersonal transfer effects targeted data comparisons demonstrated that the actor who fetched the cylinder from where the other actor had put it was systematically less surprised by cylinder-weight changes than the actor who was first confronted with such changes. In addition, a moderate, accuracy-constraint independent adaptation to each other’s movement speed was found. The current findings suggest that motor resonance plays only a moderate role in collaborative motor control and confirm the independency between sensorimotor and cognitive processing of action-related information. PMID:17256158

"My legs affect me a lot. … I can no longer walk to the forest to fetch firewood": challenges related to health and the performance of daily tasks for older women in a high HIV context.

PubMed

Schatz, Enid; Gilbert, Leah

2014-01-01

Compromised health negatively impacts older persons' ability to participate in expected social roles. Researchers have published little empirical work, however, to explore these issues in HIV endemic African settings. Qualitative interviews with 30 women, aged 60-plus, in rural South Africa, provide insight into the relationship between health and daily activities, with attention to the fulfillment of social roles. In this poor HIV endemic context, older women make connections between their compromised health and their (lack of) capacity to perform the daily tasks that they view as expected of them. By expanding the conceptualization of health to include the capacity to achieve the expectations and perform the tasks expected of one, we better understand how and why health and performance of daily activities are so intricately linked in the minds of respondents. This also provides a starting point for thinking about the social and structural support needed by older persons in these settings, especially as HIV erodes familial supports.

Gene Graphics: a genomic neighborhood data visualization web application.

PubMed

Harrison, Katherine J; Crécy-Lagard, Valérie de; Zallot, Rémi

2018-04-15

The examination of gene neighborhood is an integral part of comparative genomics but no tools to produce publication quality graphics of gene clusters are available. Gene Graphics is a straightforward web application for creating such visuals. Supported inputs include National Center for Biotechnology Information gene and protein identifiers with automatic fetching of neighboring information, GenBank files and data extracted from the SEED database. Gene representations can be customized for many parameters including gene and genome names, colors and sizes. Gene attributes can be copied and pasted for rapid and user-friendly customization of homologous genes between species. In addition to Portable Network Graphics and Scalable Vector Graphics, produced representations can be exported as Tagged Image File Format or Encapsulated PostScript, formats that are standard for publication. Hands-on tutorials with real life examples inspired from publications are available for training. Gene Graphics is freely available at https://katlabs.cc/genegraphics/ and source code is hosted at https://github.com/katlabs/genegraphics. katherinejh@ufl.edu or remizallot@ufl.edu. Supplementary data are available at Bioinformatics online.

MINERAL AND BIOCHEMICAL ANALYSIS OF VARIOUS PARTS OF CISSUS QUADRANGULARIS LINN

PubMed Central

Udayakumar, R.; Sundaran, M.; Krishna, Raghuram

2004-01-01

Ash, minerals and biochemical contents were determined in various parts of root, stem and leaf of Cissus quadrangularis. The maximum ash content was observed in the root. The maximum concentration of carbohydrate and protein in the root and phosphorus, iron, calcium and lipids in the stem were observed. PMID:22557157

40 CFR 141.11 - Maximum contaminant levels for inorganic chemicals.

Code of Federal Regulations, 2011 CFR

2011-07-01

... levels that exceed 10 mg/l; and (4) No adverse health effects shall result. [40 FR 59570, Dec. 24, 1975... arsenic applies only to community water systems. The analyses and determination of compliance with the 0...) The maximum contaminant level for arsenic is 0.05 milligrams per liter for community water systems...

5 CFR 531.247 - Maximum payable rate rule for GM employees.

Code of Federal Regulations, 2010 CFR

2010-01-01

... rate is a special rate, the highest previous rate (after any geographic conversion) must be compared... 5 Administrative Personnel 1 2010-01-01 2010-01-01 false Maximum payable rate rule for GM... REGULATIONS PAY UNDER THE GENERAL SCHEDULE Determining Rate of Basic Pay Special Rules for Gm Employees § 531...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

30 CFR 7.84 - Technical requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Underground Coal Mines § 7.84 Technical requirements. (a) Fuel injection adjustment. The fuel injection system of the engine shall be constructed so that the quantity of fuel injected can be controlled at a... design. (b) Maximum fuel-air ratio. At the maximum fuel-air ratio determined by § 7.87 of this part, the...

50 CFR 648.21 - Mid-Atlantic Fishery Management Council risk policy.

Code of Federal Regulations, 2014 CFR

2014-10-01

... to have an atypical life history, the maximum probability of overfishing as informed by the OFL... atypical life history is generally defined as one that has greater vulnerability to exploitation and whose... development process. (2) For stocks determined by the SSC to have a typical life history, the maximum...

50 CFR 648.21 - Mid-Atlantic Fishery Management Council risk policy.

Code of Federal Regulations, 2013 CFR

2013-10-01

... to have an atypical life history, the maximum probability of overfishing as informed by the OFL... atypical life history is generally defined as one that has greater vulnerability to exploitation and whose... development process. (2) For stocks determined by the SSC to have a typical life history, the maximum...

50 CFR 648.21 - Mid-Atlantic Fishery Management Council risk policy.

Code of Federal Regulations, 2012 CFR

2012-10-01

... to have an atypical life history, the maximum probability of overfishing as informed by the OFL... atypical life history is generally defined as one that has greater vulnerability to exploitation and whose... development process. (2) For stocks determined by the SSC to have a typical life history, the maximum...

49 CFR 213.57 - Curves; elevation and speed limitations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Curves; elevation and speed limitations. 213.57... speed limitations. (a) The maximum crosslevel on the outside rail of a curve may not be more than 8... applicable September 21, 1999.) (b)(1) The maximum allowable operating speed for each curve is determined by...

49 CFR 213.329 - Curves, elevation and speed limitations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Curves, elevation and speed limitations. 213.329... Higher § 213.329 Curves, elevation and speed limitations. (a) The maximum crosslevel on the outside rail... lower than the inside rail. (b) (1) The maximum allowable operating speed for each curve is determined...

49 CFR 213.57 - Curves; elevation and speed limitations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Curves; elevation and speed limitations. 213.57... speed limitations. (a) The maximum crosslevel on the outside rail of a curve may not be more than 8... applicable September 21, 1999.) (b)(1) The maximum allowable operating speed for each curve is determined by...

49 CFR 213.329 - Curves, elevation and speed limitations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Curves, elevation and speed limitations. 213.329... Higher § 213.329 Curves, elevation and speed limitations. (a) The maximum crosslevel on the outside rail... lower than the inside rail. (b) (1) The maximum allowable operating speed for each curve is determined...

The Nature, Function, and Impact of Inmate Communication Patterns in a Maximum Security Prison.

ERIC Educational Resources Information Center

Van Voorhis, Patricia

To determine the areas in which communication affects prison environments and prison inmates, interviews were conducted with 21 adult male inmates shortly after their admission into a federal maximum security institution. The interviews were semistructured, addressing such issues as (1) perceptions of fellow inmates and staff; (2) additional…

Potentiometric surface in the Central Oklahoma (Garber-Wellington) aquifer, Oklahoma, 2009

USGS Publications Warehouse

Mashburn, Shana L.; Magers, Jessica

2011-01-01

A study of the hydrogeology of the Central Oklahoma aquifer was started in 2008 to provide the Oklahoma Water Resources Board (OWRB) hydrogeologic data and a groundwater flow model that can be used as a tool to help manage the aquifer. The 1973 Oklahoma water law requires the OWRB to do hydrologic investigations of Oklahoma's aquifers (termed 'groundwater basins') and to determine amounts of water that may be withdrawn by permitted water users. 'Maximum annual yield' is a term used by OWRB to describe the total amount of water that can be withdrawn from a specific aquifer in any year while allowing a minimum 20-year life of the basin (Oklahoma Water Resources Board, 2010). Currently (2010), the maximum annual yield has not been determined for the Central Oklahoma aquifer. Until the maximum annual yield determination is made, water users are issued a temporary permit by the OWRB for 2 acre-feet/acre per year. The objective of the study, in cooperation with the Oklahoma Water Resources Board, was to study the hydrogeology of the Central Oklahoma aquifer to provide information that will enable the OWRB to determine the maximum annual yield of the aquifer based on different proposed management plans. Groundwater flow models are typically used by the OWRB as a tool to help determine the maximum annual yield. This report presents the potentiometric surface of the Central Oklahoma aquifer based on water-level data collected in 2009 as part of the current (2010) hydrologic study. The U.S. Geological Survey (USGS) Hydrologic Investigations Atlas HA-724 by Christenson and others (1992) presents the 1986-87 potentiometric-surface map. This 1986-87 potentiometric-surface map was made as part of the USGS National Water-Quality Assessment pilot project for the Central Oklahoma aquifer that examined the geochemical and hydrogeological processes operating in the aquifer. An attempt was made to obtain water-level measurements for the 2009 potentiometric-surface map from the wells used for the 1986-87 potentiometric-surface map. Well symbols with circles on the 2009 potentiometric-surface map (fig. 1) indicate wells that were used for the 1986-87 potentiometric-surface map.

Estimations of relative effort during sit-to-stand increase when accounting for variations in maximum voluntary torque with joint angle and angular velocity.

PubMed

Bieryla, Kathleen A; Anderson, Dennis E; Madigan, Michael L

2009-02-01

The main purpose of this study was to compare three methods of determining relative effort during sit-to-stand (STS). Fourteen young (mean 19.6+/-SD 1.2 years old) and 17 older (61.7+/-5.5 years old) adults completed six STS trials at three speeds: slow, normal, and fast. Sagittal plane joint torques at the hip, knee, and ankle were calculated through inverse dynamics. Isometric and isokinetic maximum voluntary contractions (MVC) for the hip, knee, and ankle were collected and used for model parameters to predict the participant-specific maximum voluntary joint torque. Three different measures of relative effort were determined by normalizing STS joint torques to three different estimates of maximum voluntary torque. Relative effort at the hip, knee, and ankle were higher when accounting for variations in maximum voluntary torque with joint angle and angular velocity (hip=26.3+/-13.5%, knee=78.4+/-32.2%, ankle=27.9+/-14.1%) compared to methods which do not account for these variations (hip=23.5+/-11.7%, knee=51.7+/-15.0%, ankle=20.7+/-10.4%). At higher velocities, the difference in calculating relative effort with respect to isometric MVC or incorporating joint angle and angular velocity became more evident. Estimates of relative effort that account for the variations in maximum voluntary torque with joint angle and angular velocity may provide higher levels of accuracy compared to methods based on measurements of maximal isometric torques.

Limits to anaerobic energy and cytosolic concentration in the living cell.

PubMed

Paglietti, A

2015-01-01

For many physical systems at any given temperature, the set of all states where the system's free energy reaches its largest value can be determined from the system's constitutive equations of internal energy and entropy, once a state of that set is known. Such an approach is fraught with complications when applied to a living cell, because the cell's cytosol contains thousands of solutes, and thus thousands of state variables, which makes determination of its state impractical. We show here that, when looking for the maximum energy that the cytosol can store and release, detailed information on cytosol composition is redundant. Compatibility with cell's life requires that a single variable that represents the overall concentration of cytosol solutes must fall between defined limits, which can be determined by dehydrating and overhydrating the cell to its maximum capacity. The same limits are shown to determine, in particular, the maximum amount of free energy that a cell can supply in fast anaerobic processes, starting from any given initial state. For a typical skeletal muscle in normal physiological conditions this energy, i.e., the maximum anaerobic capacity to do work, is calculated to be about 960 J per kg of muscular mass. Such energy decreases as the overall concentration of solutes in the cytosol is increased. Similar results apply to any kind of cell. They provide an essential tool to understand and control the macroscopic response of single cells and multicellular cellular tissues alike. The applications include sport physiology, cell aging, disease produced cell damage, drug absorption capacity, to mention the most obvious ones.

Limits to anaerobic energy and cytosolic concentration in the living cell

NASA Astrophysics Data System (ADS)

Paglietti, A.

2015-11-01

For many physical systems at any given temperature, the set of all states where the system's free energy reaches its largest value can be determined from the system's constitutive equations of internal energy and entropy, once a state of that set is known. Such an approach is fraught with complications when applied to a living cell, because the cell's cytosol contains thousands of solutes, and thus thousands of state variables, which makes determination of its state impractical. We show here that, when looking for the maximum energy that the cytosol can store and release, detailed information on cytosol composition is redundant. Compatibility with cell's life requires that a single variable that represents the overall concentration of cytosol solutes must fall between defined limits, which can be determined by dehydrating and overhydrating the cell to its maximum capacity. The same limits are shown to determine, in particular, the maximum amount of free energy that a cell can supply in fast anaerobic processes, starting from any given initial state. For a typical skeletal muscle in normal physiological conditions this energy, i.e., the maximum anaerobic capacity to do work, is calculated to be about 960 J per kg of muscular mass. Such energy decreases as the overall concentration of solutes in the cytosol is increased. Similar results apply to any kind of cell. They provide an essential tool to understand and control the macroscopic response of single cells and multicellular cellular tissues alike. The applications include sport physiology, cell aging, disease produced cell damage, drug absorption capacity, to mention the most obvious ones.

A systematic method of interconnection optimization for dense-array concentrator photovoltaic system.

PubMed

Siaw, Fei-Lu; Chong, Kok-Keong

2013-01-01

This paper presents a new systematic approach to analyze all possible array configurations in order to determine the most optimal dense-array configuration for concentrator photovoltaic (CPV) systems. The proposed method is fast, simple, reasonably accurate, and very useful as a preliminary study before constructing a dense-array CPV panel. Using measured flux distribution data, each CPV cells' voltage and current values at three critical points which are at short-circuit, open-circuit, and maximum power point are determined. From there, an algorithm groups the cells into basic modules. The next step is I-V curve prediction, to find the maximum output power of each array configuration. As a case study, twenty different I-V predictions are made for a prototype of nonimaging planar concentrator, and the array configuration that yields the highest output power is determined. The result is then verified by assembling and testing of an actual dense-array on the prototype. It was found that the I-V curve closely resembles simulated I-V prediction, and measured maximum output power varies by only 1.34%.

Human vision is determined based on information theory.

PubMed

Delgado-Bonal, Alfonso; Martín-Torres, Javier

2016-11-03

It is commonly accepted that the evolution of the human eye has been driven by the maximum intensity of the radiation emitted by the Sun. However, the interpretation of the surrounding environment is constrained not only by the amount of energy received but also by the information content of the radiation. Information is related to entropy rather than energy. The human brain follows Bayesian statistical inference for the interpretation of visual space. The maximization of information occurs in the process of maximizing the entropy. Here, we show that the photopic and scotopic vision absorption peaks in humans are determined not only by the intensity but also by the entropy of radiation. We suggest that through the course of evolution, the human eye has not adapted only to the maximum intensity or to the maximum information but to the optimal wavelength for obtaining information. On Earth, the optimal wavelengths for photopic and scotopic vision are 555 nm and 508 nm, respectively, as inferred experimentally. These optimal wavelengths are determined by the temperature of the star (in this case, the Sun) and by the atmospheric composition.

Human vision is determined based on information theory

NASA Astrophysics Data System (ADS)

Delgado-Bonal, Alfonso; Martín-Torres, Javier

2016-11-01

It is commonly accepted that the evolution of the human eye has been driven by the maximum intensity of the radiation emitted by the Sun. However, the interpretation of the surrounding environment is constrained not only by the amount of energy received but also by the information content of the radiation. Information is related to entropy rather than energy. The human brain follows Bayesian statistical inference for the interpretation of visual space. The maximization of information occurs in the process of maximizing the entropy. Here, we show that the photopic and scotopic vision absorption peaks in humans are determined not only by the intensity but also by the entropy of radiation. We suggest that through the course of evolution, the human eye has not adapted only to the maximum intensity or to the maximum information but to the optimal wavelength for obtaining information. On Earth, the optimal wavelengths for photopic and scotopic vision are 555 nm and 508 nm, respectively, as inferred experimentally. These optimal wavelengths are determined by the temperature of the star (in this case, the Sun) and by the atmospheric composition.

Novel plasma source for safe beryllium spectral line studies in the presence of beryllium dust

NASA Astrophysics Data System (ADS)

Stankov, B. D.; Vinić, M.; Gavrilović Božović, M. R.; Ivković, M.

2018-05-01

Plasma source for beryllium spectral line studies in the presence of beryllium dust particles was realised. The guideline during construction was to prevent exposure to formed dust, considering the toxicity of beryllium. Plasma source characterization through determination of optimal working conditions is described. The necessary conditions for Be spectral line appearance and optimal conditions for line shape measurements are found. It is proven experimentally that under these conditions dust appears coincidently with the second current maximum. The electron density measured after discharge current maximum is determined from the peak separation of the hydrogen Balmer beta spectral line, and the electron temperature is determined from the ratios of the relative intensities of Be spectral lines emitted from successive ionized stages of atoms. Maximum values of electron density and temperature are measured to be 9.3 × 1022 m-3 and 16 800 K, respectively. Construction details and testing of the BeO discharge tube in comparison with SiO2 and Al2O3 discharge tubes are also presented in this paper.

A Systematic Method of Interconnection Optimization for Dense-Array Concentrator Photovoltaic System

PubMed Central

Siaw, Fei-Lu

2013-01-01

This paper presents a new systematic approach to analyze all possible array configurations in order to determine the most optimal dense-array configuration for concentrator photovoltaic (CPV) systems. The proposed method is fast, simple, reasonably accurate, and very useful as a preliminary study before constructing a dense-array CPV panel. Using measured flux distribution data, each CPV cells' voltage and current values at three critical points which are at short-circuit, open-circuit, and maximum power point are determined. From there, an algorithm groups the cells into basic modules. The next step is I-V curve prediction, to find the maximum output power of each array configuration. As a case study, twenty different I-V predictions are made for a prototype of nonimaging planar concentrator, and the array configuration that yields the highest output power is determined. The result is then verified by assembling and testing of an actual dense-array on the prototype. It was found that the I-V curve closely resembles simulated I-V prediction, and measured maximum output power varies by only 1.34%. PMID:24453823

Human vision is determined based on information theory

PubMed Central

Delgado-Bonal, Alfonso; Martín-Torres, Javier

2016-01-01

It is commonly accepted that the evolution of the human eye has been driven by the maximum intensity of the radiation emitted by the Sun. However, the interpretation of the surrounding environment is constrained not only by the amount of energy received but also by the information content of the radiation. Information is related to entropy rather than energy. The human brain follows Bayesian statistical inference for the interpretation of visual space. The maximization of information occurs in the process of maximizing the entropy. Here, we show that the photopic and scotopic vision absorption peaks in humans are determined not only by the intensity but also by the entropy of radiation. We suggest that through the course of evolution, the human eye has not adapted only to the maximum intensity or to the maximum information but to the optimal wavelength for obtaining information. On Earth, the optimal wavelengths for photopic and scotopic vision are 555 nm and 508 nm, respectively, as inferred experimentally. These optimal wavelengths are determined by the temperature of the star (in this case, the Sun) and by the atmospheric composition. PMID:27808236

Generating a Simulated Fluid Flow over a Surface Using Anisotropic Diffusion

NASA Technical Reports Server (NTRS)

Rodriguez, David L. (Inventor); Sturdza, Peter (Inventor)

2016-01-01

A fluid-flow simulation over a computer-generated surface is generated using a diffusion technique. The surface is comprised of a surface mesh of polygons. A boundary-layer fluid property is obtained for a subset of the polygons of the surface mesh. A gradient vector is determined for a selected polygon, the selected polygon belonging to the surface mesh but not one of the subset of polygons. A maximum and minimum diffusion rate is determined along directions determined using the gradient vector corresponding to the selected polygon. A diffusion-path vector is defined between a point in the selected polygon and a neighboring point in a neighboring polygon. An updated fluid property is determined for the selected polygon using a variable diffusion rate, the variable diffusion rate based on the minimum diffusion rate, maximum diffusion rate, and the gradient vector.

Method of operating a thermoelectric generator

DOEpatents

Reynolds, Michael G; Cowgill, Joshua D

2013-11-05

A method for operating a thermoelectric generator supplying a variable-load component includes commanding the variable-load component to operate at a first output and determining a first load current and a first load voltage to the variable-load component while operating at the commanded first output. The method also includes commanding the variable-load component to operate at a second output and determining a second load current and a second load voltage to the variable-load component while operating at the commanded second output. The method includes calculating a maximum power output of the thermoelectric generator from the determined first load current and voltage and the determined second load current and voltage, and commanding the variable-load component to operate at a third output. The commanded third output is configured to draw the calculated maximum power output from the thermoelectric generator.

Prompt merger collapse and the maximum mass of neutron stars.

PubMed

Bauswein, A; Baumgarte, T W; Janka, H-T

2013-09-27

We perform hydrodynamical simulations of neutron-star mergers for a large sample of temperature-dependent nuclear equations of state and determine the threshold mass above which the merger remnant promptly collapses to form a black hole. We find that, depending on the equation of state, the threshold mass is larger than the maximum mass of a nonrotating star in isolation by between 30 and 70 percent. Our simulations also show that the ratio between the threshold mass and maximum mass is tightly correlated with the compactness of the nonrotating maximum-mass configuration. We speculate on how this relation can be used to derive constraints on neutron-star properties from future observations.

Observations From the Coupled Boundary Layer Air-Sea Transfer Experiment in Hurricanes

NASA Astrophysics Data System (ADS)

Black, P. G.

2006-12-01

The CBLAST field program conducted from 2002-2004 has shown that the wind speed range for which turbulent momentum and moisture exchange coefficients have been derived based upon direct flux measurements has been extended by 30 and 60 percent, respectively, from airborne observations in Hurricanes Fabian and Isabel in 2003. The drag coefficient (CD) values derived from CBLAST momentum flux measurements show CD becoming invariant with wind speed near a 23 ms-1 threshold rather than a hurricane-force threshold near 33 ms-1. Values above 23 ms-1 are lower than previous open ocean measurements. The Dalton number estimates (CE) derived from CBLAST moisture flux measurements are shown to be invariant with wind speed to 30 ms-1, in approximate agreement with previous measurements at lower winds. These observations imply a CE/CD ratio of approximately 0.7, suggesting that additional energy sources are necessary for hurricanes to achieve their maximum potential intensity. Two such additional mechanisms for augmented moisture flux in the boundary layer might be 1) augmented wave breaking by short-crested, fetch limited waves suggested by whitecap aerial coverage measurements, and 2) sea spray at high winds suggested by laboratory spray source function measurements. Linear coherent features in the hurricane boundary layer are a third mechanism, observed during CBLAST 2002 aircraft measurements, to have wavelengths of 0.9 to 1.2 km. Linear features of the same wavelength range were observed in nearly-concurrent RADARSAT Synthetic Aperture Radar (SAR) imagery. Arrays of drifting buoys and subsurface floats were successfully deployed ahead of Hurricanes Fabian (2003) and Frances (2004): 16 (6) and 38 (14) drifters (floats). Two types of surface drifters and three types of floats provided observations of surface and subsurface oceanic currents, temperature, salinity, gas exchange, bubble concentrations and surface wave spectra to a depth of 200 m on a continuous basis before, during and after storm passage. Float observations indicated deepening of the mixed layer from 40 to 120 m in approximately 8 hr with a corresponding decrease in SST in the right-rear quadrant of 3.2 ºC in 11 hr, roughly one-half inertial period. Strong inertial currents with a peak amplitude of 1.5 ms-1 were observed. Vertical structure showed the critical Richardson number was reached sporadically during the mixed-layer deepening event, suggesting shear-induced mixing as a prominent mechanism during storm passage.

40 CFR 63.43 - Maximum achievable control technology (MACT) determinations for constructed and reconstructed...

Code of Federal Regulations, 2011 CFR

2011-07-01

... determinations for alternative operating scenarios. Approval of such determinations satisfies the requirements of section 112(g) of each such scenario. (4) Regardless of the review process, the MACT emission limitation... determined by the permitting authority. (2) Based upon available information, as defined in this subpart, the...

78 FR 57749 - Endangered and Threatened Wildlife and Plants; Determination of Endangered Species Status for...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-19

... Service 50 CFR Part 17 Endangered and Threatened Wildlife and Plants; Determination of Endangered Species... Endangered and Threatened Wildlife and Plants; Determination of Endangered Species Status for Mount... determination on our proposal within 1 year. Critical habitat shall be designated, to the maximum extent prudent...

Strategies to reduce exposure of fumonisins from complementary foods in rural Tanzania.

PubMed

Kimanya, Martin E; De Meulenaer, Bruno; Van Camp, John; Baert, Katleen; Kolsteren, Patrick

2012-10-01

Feeding infants with maize can expose them to fumonisin mycotoxins. We assessed fumonisin exposure from complementary foods in rural Tanzania and determined strategies to reduce the exposure. We conducted a cross-sectional study in four villages of Tarakea division, Northern Tanzania. We used a repeat 24-hour dietary recall to collect data of maize consumption as complementary food for 254 infants aged 6-8 months. Fumonisin concentrations in the maize were also estimated. Fumonisin exposure was assessed using @risk analysis software. With the software, several maximum fumonisin contamination and maize consumption patterns were combined in order to determine effective strategies for minimizing fumonisin exposure. Of the infants, 89% consumed maize at amounts up to 158g/person/day (mean; 43g/person/day±28). The maize was contaminated with fumonisins at levels up to 3201µgkg(-1) . Risk of fumonisin intake above the provisional maximum tolerable daily limit of 2µgkg(-1) body weight was 15% (95% confidence interval; 10-19). The risk was minimized when the maximum contamination was set at 150µgkg(-1) . The risk was also minimized when the maximum consumption was set at 20g/child/day while keeping the maximum contamination at the European Union (EU) maximum tolerated limit (MTL) of 1000µgkg(-1) . Considering the economical and technological limitations of adopting good agricultural practices in rural Tanzania, it is practically difficult to reduce contamination in maize to 150µgkg(-1) . We suggest adoption of the EU MTL of 1000µgkg(-1) for fumonisins in maize and reduction, by replacement with another cereal, of the maize component in complementary foods to a maximum intake of 20g/child/day. © 2011 Blackwell Publishing Ltd.

Using lod-score differences to determine mode of inheritance: a simple, robust method even in the presence of heterogeneity and reduced penetrance.

PubMed

Greenberg, D A; Berger, B

1994-10-01

Determining the mode of inheritance is often difficult under the best of circumstances, but when segregation analysis is used, the problems of ambiguous ascertainment procedures, reduced penetrance, heterogeneity, and misdiagnosis make mode-of-inheritance determinations even more unreliable. The mode of inheritance can also be determined using a linkage-based method (maximized maximum lod score or mod score) and association-based methods, which can overcome many of these problems. In this work, we determined how much information is necessary to reliably determine the mode of inheritance from linkage data when heterogeneity and reduced penetrance are present in the data set. We generated data sets under both dominant and recessive inheritance with reduced penetrance and with varying fractions of linked and unlinked families. We then analyzed those data sets, assuming reduced penetrance, both dominant and recessive inheritance, and no heterogeneity. We investigated the reliability of two methods for determining the mode of inheritance from the linkage data. The first method examined the difference (delta) between the maximum lod scores calculated under the two mode-of-inheritance assumptions. We found that if delta was > 1.5, then the higher of the two maximum lod scores reflected the correct mode of inheritance with high reliability and that a delta of 2.5 appeared to practically guarantee a correct mode-of-inheritance inference. Furthermore, this reliability appeared to be virtually independent of alpha, the fraction of linked families in the data set, although the reliability decreased slightly as alpha fell below .50.(ABSTRACT TRUNCATED AT 250 WORDS)

Determination of a natural valence-band offset - The case of HgTe and CdTe

NASA Technical Reports Server (NTRS)

Shih, C. K.; Spicer, W. E.

1987-01-01

A method to determine a natural valence-band offset (NVBO), i.e., the change in the valence-band maximum energy which is intrinsic to the bulk band structures of semiconductors is proposed. The HgTe-CdTe system is used as an example in which it is found that the valence-band maximum of HgTe lies 0.35 + or - 0.06 eV above that of CdTe. The NVBO of 0.35 eV is in good agreement with the X-ray photoemission spectroscopy measurement of the heterojunction offset. The procedure to determine the NVBO between semiconductors, and its implication on the heterojunction band lineup and the electronic structures of semiconductor alloys, are discussed.

Strength determination of brittle materials as curved monolithic structures.

PubMed

Hooi, P; Addison, O; Fleming, G J P

2014-04-01

The dental literature is replete with "crunch the crown" monotonic load-to-failure studies of all-ceramic materials despite fracture behavior being dominated by the indenter contact surface. Load-to-failure data provide no information on stress patterns, and comparisons among studies are impossible owing to variable testing protocols. We investigated the influence of nonplanar geometries on the maximum principal stress of curved discs tested in biaxial flexure in the absence of analytical solutions. Radii of curvature analogous to elements of complex dental geometries and a finite element analysis method were integrated with experimental testing as a surrogate solution to calculate the maximum principal stress at failure. We employed soda-lime glass discs, a planar control (group P, n = 20), with curvature applied to the remaining discs by slump forming to different radii of curvature (30, 20, 15, and 10 mm; groups R30-R10). The mean deflection (group P) and radii of curvature obtained on slumping (groups R30-R10) were determined by profilometry before and after annealing and surface treatment protocols. Finite element analysis used the biaxial flexure load-to-failure data to determine the maximum principal stress at failure. Mean maximum principal stresses and load to failure were analyzed with one-way analyses of variance and post hoc Tukey tests (α = 0.05). The measured radii of curvature differed significantly among groups, and the radii of curvature were not influenced by annealing. Significant increases in the mean load to failure were observed as the radius of curvature was reduced. The maximum principal stress did not demonstrate sensitivity to radius of curvature. The findings highlight the sensitivity of failure load to specimen shape. The data also support the synergistic use of bespoke computational analysis with conventional mechanical testing and highlight a solution to complications with complex specimen geometries.

The maximum intelligible range of the human voice

NASA Astrophysics Data System (ADS)

Boren, Braxton

This dissertation examines the acoustics of the spoken voice at high levels and the maximum number of people that could hear such a voice unamplified in the open air. In particular, it examines an early auditory experiment by Benjamin Franklin which sought to determine the maximum intelligible crowd for the Anglican preacher George Whitefield in the eighteenth century. Using Franklin's description of the experiment and a noise source on Front Street, the geometry and diffraction effects of such a noise source are examined to more precisely pinpoint Franklin's position when Whitefield's voice ceased to be intelligible. Based on historical maps, drawings, and prints, the geometry and material of Market Street is constructed as a computer model which is then used to construct an acoustic cone tracing model. Based on minimal values of the Speech Transmission Index (STI) at Franklin's position, Whitefield's on-axis Sound Pressure Level (SPL) at 1 m is determined, leading to estimates centering around 90 dBA. Recordings are carried out on trained actors and singers to determine their maximum time-averaged SPL at 1 m. This suggests that the greatest average SPL achievable by the human voice is 90-91 dBA, similar to the median estimates for Whitefield's voice. The sites of Whitefield's largest crowds are acoustically modeled based on historical evidence and maps. Based on Whitefield's SPL, the minimal STI value, and the crowd's background noise, this allows a prediction of the minimally intelligible area for each site. These yield maximum crowd estimates of 50,000 under ideal conditions, while crowds of 20,000 to 30,000 seem more reasonable when the crowd was reasonably quiet and Whitefield's voice was near 90 dBA.

ESTIMATE OF SOLAR MAXIMUM USING THE 1-8 Å GEOSTATIONARY OPERATIONAL ENVIRONMENTAL SATELLITES X-RAY MEASUREMENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winter, L. M.; Balasubramaniam, K. S., E-mail: lwinter@aer.com

We present an alternate method of determining the progression of the solar cycle through an analysis of the solar X-ray background. Our results are based on the NOAA Geostationary Operational Environmental Satellites (GOES) X-ray data in the 1-8 Å band from 1986 to the present, covering solar cycles 22, 23, and 24. The X-ray background level tracks the progression of the solar cycle through its maximum and minimum. Using the X-ray data, we can therefore make estimates of the solar cycle progression and the date of solar maximum. Based upon our analysis, we conclude that the Sun reached its hemisphere-averagedmore » maximum in solar cycle 24 in late 2013. This is within six months of the NOAA prediction of a maximum in spring 2013.« less

On Atom-Bond Connectivity Index

NASA Astrophysics Data System (ADS)

Zhou, Bo; Xing, Rundan

2011-02-01

The atom-bond connectivity (ABC) index, introduced by Estrada et al. in 1998, displays an excellent correlation with the formation heat of alkanes. We give upper bounds for this graph invariant using the number of vertices, the number of edges, the Randíc connectivity indices, and the first Zagreb index. We determine the unique tree with the maximum ABC index among trees with given numbers of vertices and pendant vertices, and the n-vertex trees with the maximum, and the second, the third, and the fourth maximum ABC indices for n ≥ 6.

Efficiency at Maximum Power Output of a Quantum-Mechanical Brayton Cycle

NASA Astrophysics Data System (ADS)

Yuan, Yuan; He, Ji-Zhou; Gao, Yong; Wang, Jian-Hui

2014-03-01

The performance in finite time of a quantum-mechanical Brayton engine cycle is discussed, without introduction of temperature. The engine model consists of two quantum isoenergetic and two quantum isobaric processes, and works with a single particle in a harmonic trap. Directly employing the finite-time thermodynamics, the efficiency at maximum power output is determined. Extending the harmonic trap to a power-law trap, we find that the efficiency at maximum power is independent of any parameter involved in the model, but depends on the confinement of the trapping potential.

Maximum powers of low-loss series-shunt FET RF switches

NASA Astrophysics Data System (ADS)

Yang, Z.; Hu, X.; Yang, J.; Simin, G.; Shur, M.; Gaska, R.

2009-02-01

Low-loss high-power single pole single throw (SPST) monolithic RF switch based on AlGaN/GaN heterojunction field effect transistors (HFETs) demonstrate the insertion loss and isolation of 0.15 dB and 45.9 dB at 0.5 GHz and 0.23 dB and 34.3 dB at 2 GHz. Maximum switching powers are estimated +47 dBm or higher. Factors determining the maximum switching powers are analyzed. Design principles to obtain equally high switching powers in the ON and OFF-states are developed.

Carrying water may be a major contributor to disability from musculoskeletal disorders in low income countries: a cross-sectional survey in South Africa, Ghana and Vietnam.

PubMed

Geere, Jo-Anne; Bartram, Jamie; Bates, Laura; Danquah, Leslie; Evans, Barbara; Fisher, Michael B; Groce, Nora; Majuru, Batsirai; Mokoena, Michael M; Mukhola, Murembiwa S; Nguyen-Viet, Hung; Duc, Phuc Pham; Williams, Ashley Rhoderick; Schmidt, Wolf-Peter; Hunter, Paul R

2018-06-01

The Sustainable Development Goals include commitments to end poverty, and promote education for all, gender equality, the availability of water and decent work for all. An important constraint is the fact that each day, many millions of women and children, and much less frequently men, carry their household's water home from off-plot sources. The burden of fetching water exacerbates gender inequality by keeping women out of education and paid employment. Despite speculation about the potential health impacts of fetching water, there is very little empirical evidence. We report the first large study of the health impacts of carrying water on women and children. A cross-sectional survey was conducted in South Africa, Ghana and Vietnam during 2012. It investigated water carrying methods and health status. Because areas of self-reported pain were correlated we undertook factor analysis of sites of reported pain, to interpret patterns of pain reporting. Regression analysis using Generalised Estimating Equations (GEE) investigated water carrying as a risk factor for general health and self-reported pain. People who previously carried water had increased relative risk of reporting pain in the hands (risk ratio RR 3.62, 95% confidence interval CI 1.34 to 9.75) and upper back (RR 2.27, 95% CI 1.17 to 4.40), as did people who currently carry water (RR hand pain 3.11, 95% CI 1.34 to 7.23; RR upper back pain 2.16, 95% CI 1.25 to 3.73). The factor analysis results indicate that factor 1, 'axial compression', which is correlated with pain in the head and upper back, chest/ribs, hands, feet and abdomen/stomach, is associated with currently (0.30, 95% CI 0.17 to 0.43) or previously (0.21, 95% CI 0.01 to 0.42) carrying water. Factor 2, 'soft tissue strain', which is correlated with pain in the neck, shoulders/arms, lower back and hips/pelvis or legs, is marginally negatively associated with currently (-0.18, 95% CI -0.32 to -0.04) carrying water. The factor 'axial compression' was more strongly associated with carrying water containers on the head. Participants who reported a history of current or past water carrying more frequently reported pain in locations most likely to be associated with sustained spinal axial compression in the cervical region. Given the fact that cervical spinal conditions are globally one of the more common causes of disability, our findings suggest that water carrying, especially by head loading is a major contributing factor in musculoskeletal disease burden in low income countries. Our findings support the proposed indicator for monitoring SDG6.1: "Percentage of population using safely managed drinking water services at home."

National Dam Inspection Program. Big Elk Lake Dam (NDI I.D. PA-0056 DER I.D. 058-019) Susquehanna River Basin, Elk Lake Stream, Susquehanna County, Pennsylvania. Phase I Inspection Report.

DTIC Science & Technology

1981-03-19

Drainage Area 2.88 square miles(") b. Discharge at Dam Site ( cfs ) Maximum known flood at dam site Unknown Outlet conduit at maximum pool Not...the spillway was determined to be 164 cfs , based on the available 2.7-foot freeboard relative to the crest of the embankment. The Big Elk Lake watershed...computer analysis are presented in Appendix D. The 100-year flood, determined according to the recommended procedure, was found to have a peak of 2290 cfs

On the road performance tests of electric test vehicle for correlation with road load simulator

NASA Technical Reports Server (NTRS)

Dustin, M. O.; Slavik, R. J.

1982-01-01

A dynamometer (road load simulator) is used to test and evaluate electric vehicle propulsion systems. To improve correlation between system tests on the road load simulator and on the road, similar performance tests are conducted using the same vehicle. The results of track tests on the electric propulsion system test vehicle are described. The tests include range at constant speeds and over SAE J227a driving cycles, maximum accelerations, maximum gradability, and tire rolling resistance determination. Road power requirements and energy consumption were also determined from coast down tests.

Determination of the wind power systems load to achieve operation in the maximum energy area

NASA Astrophysics Data System (ADS)

Chioncel, C. P.; Tirian, G. O.; Spunei, E.; Gillich, N.

2018-01-01

This paper analyses the operation of the wind turbine, WT, in the maximum power point, MPP, by linking the load of the Permanent Magnet Synchronous Generator, PMSG, with the wind speed value. The load control methods at wind power systems aiming an optimum performance in terms of energy are based on the fact that the energy captured by the wind turbine significantly depends on the mechanical angular speed of the wind turbine. The presented control method consists in determining the optimal mechanical angular speed, ωOPTIM, using an auxiliary low power wind turbine, WTAUX, operating without load, at maximum angular velocity, ωMAX. The method relies on the fact that the ratio ωOPTIM/ωMAX has a constant value for a given wind turbine and does not depend on the time variation of the wind speed values.

Design of experiments with four-factors for a PEM fuel cell optimization

NASA Astrophysics Data System (ADS)

Olteanu, V.; Pǎtularu, L.; Popescu, C. L.; Popescu, M. O.; Crǎciunescu, A.

2017-07-01

Nowadays, many research efforts are allocated for the development of fuel cells, since they constitute a carbon-free electrical energy generator which can be used for stationary, mobile and portable applications. The maximum value of the delivered power of a fuel cell depends on many factors as: the height of plates' channels, the stoichiometry level of the air flow, the air pressure for the cathode, and of the actual operating electric current density. In this paper, two levels, full four-factors factorial experiment has been designed in order to obtain the appropriate response surface which approximates the maximum delivered power dependence of the above-mentioned factors. The optimum set of the fuel-cell factors which determine the maximum value of the delivered power was determined and a comparison between simulated and measured optimal Power versus Current Density characteristics is given.

Calculations of the Performance of a Compression-Ignition Engine-Compressor Turbine Combination I : Performance of a Highly Supercharged Compression-Ignition Engine

NASA Technical Reports Server (NTRS)

Sanders, J. C.; Mendelson, Alexander

1945-01-01

Small high-speed single-cylinder compression-ignition engines were tested to determine their performance characteristics under high supercharging. Calculations were made on the energy available in the exhaust gas of the compression-ignition engines. The maximum power at any given maximum cylinder pressure was obtained when the compression pressure was equal to the maximum cylinder pressure. Constant-pressure combustion was found possible at an engine speed of 2200 rpm. Exhaust pressures and temperatures were determined from an analysis of indicator cards. The analysis showed that, at rich mixtures with the exhaust back pressure equal to the inlet-air pressure, there is excess energy available for driving a turbine over that required for supercharging. The presence of this excess energy indicates that a highly supercharged compression-ignition engine might be desirable as a compressor and combustion chamber for a turbine.

49 CFR 173.302a - Additional requirements for shipment of nonliquefied (permanent) compressed gases in...

Code of Federal Regulations, 2011 CFR

2011-10-01

... elastic expansion was determined at the time of the last test or retest by the water jacket method. (3) Either the average wall stress or the maximum wall stress does not exceed the wall stress limitation shown in the following table: Type of steel Average wall stress limitation Maximum wall stress...

Optimizing any-aged management of mixed-species stands: II. effects of decision criteria

Treesearch

Robert G. Haight; Robert A. Monserud

1990-01-01

The effects of maximum present value and maximum volume objectives on the efficiencies of alternative silvicultural systems are determined by solving any-aged management problems for mixed-conifer stands in the Northern Rocky Mountains. Any-aged management problems are formulated with periodic planting and harvesting controls and without constraints on the stand age or...

Effect of Training Frequency on Maximum Expiratory Pressure

ERIC Educational Resources Information Center

Anand, Supraja; El-Bashiti, Nour; Sapienza, Christine

2012-01-01

Purpose: To determine the effects of expiratory muscle strength training (EMST) frequency on maximum expiratory pressure (MEP). Method: We assigned 12 healthy participants to 2 groups of training frequency (3 days per week and 5 days per week). They completed a 4-week training program on an EMST trainer (Aspire Products, LLC). MEP was the primary…

7 CFR 762.106 - Preferred and certified lender programs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... writing why the excessive loss rate is beyond their control; (B) The lender provides a written plan that...) The Agency determines that exceeding the maximum PLP loss rate standard was beyond the control of the... eligible lender under § 762.105; (2) Have a lender loss rate not in excess of the maximum CLP loss rate...

77 FR 47318 - Fisheries Off West Coast States; Coastal Pelagic Species Fisheries; Annual Specifications

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-08

... (CPS) Fishery Management Plan (FMP). The 2012 maximum HG for Pacific sardine is 109,409 metric tons (mt... framework in the FMP. This framework includes a harvest control rule that determines the maximum HG, the... 109,409 metric tons (mt) for the 2012 Pacific sardine fishing year. These catch specifications are...

77 FR 12157 - Disaster Assistance Loan Program; Maximum Term for Disaster Loans to Small Businesses With Credit...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-29

..., 2011, amended the Small Business Act to increase the maximum loan maturity from three years to seven years for business disaster victims that have been determined to have access to credit elsewhere. SBA is.... For economic injury loans, businesses with credit elsewhere remain ineligible. The new seven year term...