Sample records for deterministic accident analysis

  1. PROBABILISTIC SAFETY ASSESSMENT OF OPERATIONAL ACCIDENTS AT THE WASTE ISOLATION PILOT PLANT

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Rucker, D.F.

    2000-09-01

    This report presents a probabilistic safety assessment of radioactive doses as consequences from accident scenarios to complement the deterministic assessment presented in the Waste Isolation Pilot Plant (WIPP) Safety Analysis Report (SAR). The International Council of Radiation Protection (ICRP) recommends both assessments be conducted to ensure that ''an adequate level of safety has been achieved and that no major contributors to risk are overlooked'' (ICRP 1993). To that end, the probabilistic assessment for the WIPP accident scenarios addresses the wide range of assumptions, e.g. the range of values representing the radioactive source of an accident, that could possibly have beenmore » overlooked by the SAR. Routine releases of radionuclides from the WIPP repository to the environment during the waste emplacement operations are expected to be essentially zero. In contrast, potential accidental releases from postulated accident scenarios during waste handling and emplacement could be substantial, which necessitates the need for radiological air monitoring and confinement barriers (DOE 1999). The WIPP Safety Analysis Report (SAR) calculated doses from accidental releases to the on-site (at 100 m from the source) and off-site (at the Exclusive Use Boundary and Site Boundary) public by a deterministic approach. This approach, as demonstrated in the SAR, uses single-point values of key parameters to assess the 50-year, whole-body committed effective dose equivalent (CEDE). The basic assumptions used in the SAR to formulate the CEDE are retained for this report's probabilistic assessment. However, for the probabilistic assessment, single-point parameter values were replaced with probability density functions (PDF) and were sampled over an expected range. Monte Carlo simulations were run, in which 10,000 iterations were performed by randomly selecting one value for each parameter and calculating the dose. Statistical information was then derived from the 10,000 iteration batch, which included 5%, 50%, and 95% dose likelihood, and the sensitivity of each assumption to the calculated doses. As one would intuitively expect, the doses from the probabilistic assessment for most scenarios were found to be much less than the deterministic assessment. The lower dose of the probabilistic assessment can be attributed to a ''smearing'' of values from the high and low end of the PDF spectrum of the various input parameters. The analysis also found a potential weakness in the deterministic analysis used in the SAR, a detail on drum loading was not taken into consideration. Waste emplacement operations thus far have handled drums from each shipment as a single unit, i.e. drums from each shipment are kept together. Shipments typically come from a single waste stream, and therefore the curie loading of each drum can be considered nearly identical to that of its neighbor. Calculations show that if there are large numbers of drums used in the accident scenario assessment, e.g. 28 drums in the waste hoist failure scenario (CH5), then the probabilistic dose assessment calculations will diverge from the deterministically determined doses. As it is currently calculated, the deterministic dose assessment assumes one drum loaded to the maximum allowable (80 PE-Ci), and the remaining are 10% of the maximum. The effective average of drum curie content is therefore less in the deterministic assessment than the probabilistic assessment for a large number of drums. EEG recommends that the WIPP SAR calculations be revisited and updated to include a probabilistic safety assessment.« less

  2. 76 FR 28102 - Notice of Issuance of Regulatory Guide

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-13

    ..., Probabilistic Risk Assessment Branch, Division of Risk Analysis, Office of Nuclear Regulatory Research, U.S... approaches and methods (whether quantitative or qualitative, deterministic or probabilistic), data, and... uses in evaluating specific problems or postulated accidents, and data that the staff needs in its...

  3. Severe Accident Sequence Analysis Program: Anticipated transient without scram simulations for Browns Ferry Nuclear Plant Unit 1

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Dallman, R J; Gottula, R C; Holcomb, E E

    1987-05-01

    An analysis of five anticipated transients without scram (ATWS) was conducted at the Idaho National Engineering Laboratory (INEL). The five detailed deterministic simulations of postulated ATWS sequences were initiated from a main steamline isolation valve (MSIV) closure. The subject of the analysis was the Browns Ferry Nuclear Plant Unit 1, a boiling water reactor (BWR) of the BWR/4 product line with a Mark I containment. The simulations yielded insights to the possible consequences resulting from a MSIV closure ATWS. An evaluation of the effects of plant safety systems and operator actions on accident progression and mitigation is presented.

  4. Integrated deterministic and probabilistic safety analysis for safety assessment of nuclear power plants

    DOE PAGES

    Di Maio, Francesco; Zio, Enrico; Smith, Curtis; ...

    2015-07-06

    The present special issue contains an overview of the research in the field of Integrated Deterministic and Probabilistic Safety Assessment (IDPSA) of Nuclear Power Plants (NPPs). Traditionally, safety regulation for NPPs design and operation has been based on Deterministic Safety Assessment (DSA) methods to verify criteria that assure plant safety in a number of postulated Design Basis Accident (DBA) scenarios. Referring to such criteria, it is also possible to identify those plant Structures, Systems, and Components (SSCs) and activities that are most important for safety within those postulated scenarios. Then, the design, operation, and maintenance of these “safety-related” SSCs andmore » activities are controlled through regulatory requirements and supported by Probabilistic Safety Assessment (PSA).« less

  5. Nuclear power and probabilistic safety assessment (PSA): past through future applications

    NASA Astrophysics Data System (ADS)

    Stamatelatos, M. G.; Moieni, P.; Everline, C. J.

    1995-03-01

    Nuclear power reactor safety in the United States is about to enter a new era -- an era of risk- based management and risk-based regulation. First, there was the age of `prescribed safety assessment,' during which a series of design-basis accidents in eight categories of severity, or classes, were postulated and analyzed. Toward the end of that era, it was recognized that `Class 9,' or `beyond design basis,' accidents would need special attention because of the potentially severe health and financial consequences of these accidents. The accident at Three Mile Island showed that sequences of low-consequence, high-frequency events and human errors can be much more risk dominant than the Class 9 accidents. A different form of safety assessment, PSA, emerged and began to gain ground against the deterministic safety establishment. Eventually, this led to the current regulatory requirements for individual plant examinations (IPEs). The IPEs can serve as a basis for risk-based regulation and management, a concept that may ultimately transform the U.S. regulatory process from its traditional deterministic foundations to a process predicated upon PSA. Beyond the possibility of a regulatory environment predicated upon PSA lies the possibility of using PSA as the foundation for managing daily nuclear power plant operations.

  6. Verification of screening level for decontamination implemented after Fukushima nuclear accident

    PubMed Central

    Ogino, Haruyuki; Ichiji, Takeshi; Hattori, Takatoshi

    2012-01-01

    The screening level for decontamination that has been applied for the surface of the human body and contaminated handled objects after the Fukushima nuclear accident was verified by assessing the doses that arise from external irradiation, ingestion, inhalation and skin contamination. The result shows that the annual effective dose that arises from handled objects contaminated with the screening level for decontamination (i.e. 100 000 counts per minute) is <1 mSv y−1, which can be considered as the intervention exemption level in accordance with the International Commission on Radiological Protection recommendations. Furthermore, the screening level is also found to protect the skin from the incidence of a deterministic effect because the absorbed dose of the skin that arises from direct deposition on the surface of the human body is calculated to be lower than the threshold of the deterministic effect assuming a practical exposure duration. PMID:22228683

  7. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Clayton, Daniel James; Lipinski, Ronald J.; Bechtel, Ryan D.

    As compact and light weight power sources with reliable, long lives, Radioisotope Power Systems (RPSs) have made space missions to explore the solar system possible. Due to the hazardous material that can be released during a launch accident, the potential health risk of an accident must be quantified, so that appropriate launch approval decisions can be made. One part of the risk estimation involves modeling the response of the RPS to potential accident environments. Due to the complexity of modeling the full RPS response deterministically on dynamic variables, the evaluation is performed in a stochastic manner with a Monte Carlomore » simulation. The potential consequences can be determined by modeling the transport of the hazardous material in the environment and in human biological pathways. The consequence analysis results are summed and weighted by appropriate likelihood values to give a collection of probabilistic results for the estimation of the potential health risk. This information is used to guide RPS designs, spacecraft designs, mission architecture, or launch procedures to potentially reduce the risk, as well as to inform decision makers of the potential health risks resulting from the use of RPSs for space missions.« less

  8. Application of Non-Deterministic Methods to Assess Modeling Uncertainties for Reinforced Carbon-Carbon Debris Impacts

    NASA Technical Reports Server (NTRS)

    Lyle, Karen H.; Fasanella, Edwin L.; Melis, Matthew; Carney, Kelly; Gabrys, Jonathan

    2004-01-01

    The Space Shuttle Columbia Accident Investigation Board (CAIB) made several recommendations for improving the NASA Space Shuttle Program. An extensive experimental and analytical program has been developed to address two recommendations related to structural impact analysis. The objective of the present work is to demonstrate the application of probabilistic analysis to assess the effect of uncertainties on debris impacts on Space Shuttle Reinforced Carbon-Carbon (RCC) panels. The probabilistic analysis is used to identify the material modeling parameters controlling the uncertainty. A comparison of the finite element results with limited experimental data provided confidence that the simulations were adequately representing the global response of the material. Five input parameters were identified as significantly controlling the response.

  9. Man, road and vehicle: risk factors associated with the severity of traffic accidents.

    PubMed

    Almeida, Rosa Lívia Freitas de; Bezerra Filho, José Gomes; Braga, José Ueleres; Magalhães, Francismeire Brasileiro; Macedo, Marinila Calderaro Munguba; Silva, Kellyanne Abreu

    2013-08-01

    To describe the main characteristics of victims, roads and vehicles involved in traffic accidents and the risk factors involved in accidents resulting in death. METHODS A non-concurrent cohort study of traffic accidents in Fortaleza, CE, Northeastern Brazil, in the period from January 2004 to December 2008. Data from the Fortaleza Traffic Accidents Information System, the Mortality Information System, the Hospital Information System and the State Traffic Department Driving Licenses and Vehicle database. Deterministic and probabilistic relationship techniques were used to integrate the databases. First, descriptive analysis of data relating to people, roads, vehicles and weather was carried out. In the investigation of risk factors for death by traffic accident, generalized linear models were used. The fit of the model was verified by likelihood ratio and ROC analysis. RESULTS There were 118,830 accidents recorded in the period. The most common types of accidents were crashes/collisions (78.1%), running over pedestrians (11.9%), colliding with a fixed obstacle (3.9%), and with motorcycles (18.1%). Deaths occurred in 1.4% of accidents. The factors that were independently associated with death by traffic accident in the final model were bicycles (OR = 21.2, 95%CI 16.1;27.8), running over pedestrians OR = 5.9 (95%CI 3.7;9.2), collision with a fixed obstacle (OR = 5.7, 95%CI 3.1;10.5) and accidents involving motorcyclists (OR = 3.5, 95%CI 2.6;4.6). The main contributing factors were a single person being involved (OR = 6.6, 95%CI 4.1;10.73), presence of unskilled drivers (OR = 4.1, 95%CI 2.9;5.5) a single vehicle (OR = 3.9, 95%CI 2,3;6,4), male (OR = 2.5, 95%CI 1.9;3.3), traffic on roads under federal jurisdiction (OR = 2.4, 95%CI 1.8;3.7), early morning hours (OR = 2.4, 95%CI 1.8;3.0), and Sundays (OR = 1.7, 95%CI 1.3;2.2), adjusted according to the log-binomial model. CONCLUSIONS Activities promoting the prevention of traffic accidents should primarily focus on accidents involving two-wheeled vehicles that most often involves a single person, unskilled, male, at nighttime, on weekends and on roads where they travel at higher speeds.

  10. Stochastic Plume Simulations for the Fukushima Accident and the Deep Water Horizon Oil Spill

    NASA Astrophysics Data System (ADS)

    Coelho, E.; Peggion, G.; Rowley, C.; Hogan, P.

    2012-04-01

    The Fukushima Dai-ichi power plant suffered damage leading to radioactive contamination of coastal waters. Major issues in characterizing the extent of the affected waters were a poor knowledge of the radiation released to the coastal waters and the rather complex coastal dynamics of the region, not deterministically captured by the available prediction systems. Equivalently, during the Gulf of Mexico Deep Water Horizon oil platform accident in April 2010, significant amounts of oil and gas were released from the ocean floor. For this case, issues in mapping and predicting the extent of the affected waters in real-time were a poor knowledge of the actual amounts of oil reaching the surface and the fact that coastal dynamics over the region were not deterministically captured by the available prediction systems. To assess the ocean regions and times that were most likely affected by these accidents while capturing the above sources of uncertainty, ensembles of the Navy Coastal Ocean Model (NCOM) were configured over the two regions (NE Japan and Northern Gulf of Mexico). For the Fukushima case tracers were released on each ensemble member; their locations at each instant provided reference positions of water volumes where the signature of water released from the plant could be found. For the Deep Water Horizon oil spill case each ensemble member was coupled with a diffusion-advection solution to estimate possible scenarios of oil concentrations using perturbed estimates of the released amounts as the source terms at the surface. Stochastic plumes were then defined using a Risk Assessment Code (RAC) analysis that associates a number from 1 to 5 to each grid point, determined by the likelihood of having tracer particle within short ranges (for the Fukushima case), hence defining the high risk areas and those recommended for monitoring. For the Oil Spill case the RAC codes were determined by the likelihood of reaching oil concentrations as defined in the Bonn Agreement Oil Appearance Code. The likelihoods were taken in both cases from probability distribution functions derived from the ensemble runs. Results were compared with a control-deterministic solution and checked against available reports to assess their skill in capturing the actual observed plumes and other in-situ data, as well as their relevance for planning surveys and reconnaissance flights for both cases.

  11. Probabilistic and deterministic evaluation of uncertainty in a local scale multi-risk analysis

    NASA Astrophysics Data System (ADS)

    Lari, S.; Frattini, P.; Crosta, G. B.

    2009-04-01

    We performed a probabilistic multi-risk analysis (QPRA) at the local scale for a 420 km2 area surrounding the town of Brescia (Northern Italy). We calculated the expected annual loss in terms of economical damage and life loss, for a set of risk scenarios of flood, earthquake and industrial accident with different occurrence probabilities and different intensities. The territorial unit used for the study was the census parcel, of variable area, for which a large amount of data was available. Due to the lack of information related to the evaluation of the hazards, to the value of the exposed elements (e.g., residential and industrial area, population, lifelines, sensitive elements as schools, hospitals) and to the process-specific vulnerability, and to a lack of knowledge of the processes (floods, industrial accidents, earthquakes), we assigned an uncertainty to the input variables of the analysis. For some variables an homogeneous uncertainty was assigned on the whole study area, as for instance for the number of buildings of various typologies, and for the event occurrence probability. In other cases, as for phenomena intensity (e.g.,depth of water during flood) and probability of impact, the uncertainty was defined in relation to the census parcel area. In fact assuming some variables homogeneously diffused or averaged on the census parcels, we introduce a larger error for larger parcels. We propagated the uncertainty in the analysis using three different models, describing the reliability of the output (risk) as a function of the uncertainty of the inputs (scenarios and vulnerability functions). We developed a probabilistic approach based on Monte Carlo simulation, and two deterministic models, namely First Order Second Moment (FOSM) and Point Estimate (PE). In general, similar values of expected losses are obtained with the three models. The uncertainty of the final risk value is in the three cases around the 30% of the expected value. Each of the models, nevertheless, requires different assumptions and computational efforts, and provides results with different level of detail.

  12. Study on Material Parameters Identification of Brain Tissue Considering Uncertainty of Friction Coefficient

    NASA Astrophysics Data System (ADS)

    Guan, Fengjiao; Zhang, Guanjun; Liu, Jie; Wang, Shujing; Luo, Xu; Zhu, Feng

    2017-10-01

    Accurate material parameters are critical to construct the high biofidelity finite element (FE) models. However, it is hard to obtain the brain tissue parameters accurately because of the effects of irregular geometry and uncertain boundary conditions. Considering the complexity of material test and the uncertainty of friction coefficient, a computational inverse method for viscoelastic material parameters identification of brain tissue is presented based on the interval analysis method. Firstly, the intervals are used to quantify the friction coefficient in the boundary condition. And then the inverse problem of material parameters identification under uncertain friction coefficient is transformed into two types of deterministic inverse problem. Finally the intelligent optimization algorithm is used to solve the two types of deterministic inverse problems quickly and accurately, and the range of material parameters can be easily acquired with no need of a variety of samples. The efficiency and convergence of this method are demonstrated by the material parameters identification of thalamus. The proposed method provides a potential effective tool for building high biofidelity human finite element model in the study of traffic accident injury.

  13. DEVELOPMENT OF A NATIONAL EMERGENCY PLAN FOR MEDICAL DIAGNOSTICS AND THERAPY OF DETERMINISTIC EFFECTS AFTER RADIATION ACCIDENTS.

    PubMed

    Ziegler, Andreas

    2016-09-01

    The focus of nuclear emergency planning in Austria has been so far on mitigating effects of widespread contamination (e.g. after NPP accidents); however, these plans did not contain provisions on the medical management of an acute radiation syndrome. To close this gap, a 'Medical Radiation Emergency Plan' was created in 2009 and 2011. This paper describes the development of this plan (including the selection of consulted guidance) as well as its structure and main propositions and closes with an outlook on probable enhancements for the second edition. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  14. Soils: man-caused radioactivity and radiation forecast

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gablin, Vassily

    2007-07-01

    Available in abstract form only. Full text of publication follows: One of the main tasks of the radiation safety guarantee is non-admission of the excess over critical radiation levels. In Russia they are man-caused radiation levels. Meanwhile any radiation measurement represents total radioactivity. That is why it is hard to assess natural and man-caused contributions to total radioactivity. It is shown that soil radioactivity depends on natural factors including radioactivity of rocks and cosmic radiation as well as man-caused factors including nuclear and non-nuclear technologies. Whole totality of these factors includes unpredictable (non-deterministic) factors - nuclear explosions and radiation accidents,more » and predictable ones (deterministic) - all the rest. Deterministic factors represent background radioactivity whose trends is the base of the radiation forecast. Non-deterministic factors represent man-caused radiation treatment contribution which is to be controlled. This contribution is equal to the difference in measured radioactivity and radiation background. The way of calculation of background radioactivity is proposed. Contemporary soils are complicated technologically influenced systems with multi-leveled spatial and temporary inhomogeneity of radionuclides distribution. Generally analysis area can be characterized by any set of factors of soil radioactivity including natural and man-caused factors. Natural factors are cosmic radiation and radioactivity of rocks. Man-caused factors are shown on Fig. 1. It is obvious that man-caused radioactivity is due to both artificial and natural emitters. Any result of radiation measurement represents total radioactivity i.e. the sum of activities resulting from natural and man-caused emitters. There is no gauge which could separately measure natural and man-caused radioactivity. That is why it is so hard to assess natural and man-caused contributions to soil radioactivity. It would have been possible if human activity had led to contamination of soil only by artificial radionuclides. But we can view a totality of soil radioactivity factors in the following way. (author)« less

  15. Effects of heterogeneous traffic with speed limit zone on the car accidents

    NASA Astrophysics Data System (ADS)

    Marzoug, R.; Lakouari, N.; Bentaleb, K.; Ez-Zahraouy, H.; Benyoussef, A.

    2016-06-01

    Using the extended Nagel-Schreckenberg (NS) model, we numerically study the impact of the heterogeneity of traffic with speed limit zone (SLZ) on the probability of occurrence of car accidents (Pac). SLZ in the heterogeneous traffic has an important effect, typically in the mixture velocities case. In the deterministic case, SLZ leads to the appearance of car accidents even in the low densities, in this region Pac increases with increasing of fraction of fast vehicles (Ff). In the nondeterministic case, SLZ decreases the effect of braking probability Pb in the low densities. Furthermore, the impact of multi-SLZ on the probability Pac is also studied. In contrast with the homogeneous case [X. Li, H. Kuang, Y. Fan and G. Zhang, Int. J. Mod. Phys. C 25 (2014) 1450036], it is found that in the low densities the probability Pac without SLZ (n = 0) is low than Pac with multi-SLZ (n > 0). However, the existence of multi-SLZ in the road decreases the risk of collision in the congestion phase.

  16. HIGH-FIDELITY SIMULATION-DRIVEN MODEL DEVELOPMENT FOR COARSE-GRAINED COMPUTATIONAL FLUID DYNAMICS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hanna, Botros N.; Dinh, Nam T.; Bolotnov, Igor A.

    Nuclear reactor safety analysis requires identifying various credible accident scenarios and determining their consequences. For a full-scale nuclear power plant system behavior, it is impossible to obtain sufficient experimental data for a broad range of risk-significant accident scenarios. In single-phase flow convective problems, Direct Numerical Simulation (DNS) and Large Eddy Simulation (LES) can provide us with high fidelity results when physical data are unavailable. However, these methods are computationally expensive and cannot be afforded for simulation of long transient scenarios in nuclear accidents despite extraordinary advances in high performance scientific computing over the past decades. The major issue is themore » inability to make the transient computation parallel, thus making number of time steps required in high-fidelity methods unaffordable for long transients. In this work, we propose to apply a high fidelity simulation-driven approach to model sub-grid scale (SGS) effect in Coarse Grained Computational Fluid Dynamics CG-CFD. This approach aims to develop a statistical surrogate model instead of the deterministic SGS model. We chose to start with a turbulent natural convection case with volumetric heating in a horizontal fluid layer with a rigid, insulated lower boundary and isothermal (cold) upper boundary. This scenario of unstable stratification is relevant to turbulent natural convection in a molten corium pool during a severe nuclear reactor accident, as well as in containment mixing and passive cooling. The presented approach demonstrates how to create a correction for the CG-CFD solution by modifying the energy balance equation. A global correction for the temperature equation proves to achieve a significant improvement to the prediction of steady state temperature distribution through the fluid layer.« less

  17. A Model for Risk Analysis of Oil Tankers

    NASA Astrophysics Data System (ADS)

    Montewka, Jakub; Krata, Przemysław; Goerland, Floris; Kujala, Pentti

    2010-01-01

    The paper presents a model for risk analysis regarding marine traffic, with the emphasis on two types of the most common marine accidents which are: collision and grounding. The focus is on oil tankers as these pose the highest environmental risk. A case study in selected areas of Gulf of Finland in ice free conditions is presented. The model utilizes a well-founded formula for risk calculation, which combines the probability of an unwanted event with its consequences. Thus the model is regarded a block type model, consisting of blocks for the probability of collision and grounding estimation respectively as well as blocks for consequences of an accident modelling. Probability of vessel colliding is assessed by means of a Minimum Distance To Collision (MDTC) based model. The model defines in a novel way the collision zone, using mathematical ship motion model and recognizes traffic flow as a non homogeneous process. The presented calculations address waterways crossing between Helsinki and Tallinn, where dense cross traffic during certain hours is observed. For assessment of a grounding probability, a new approach is proposed, which utilizes a newly developed model, where spatial interactions between objects in different locations are recognized. A ship at a seaway and navigational obstructions may be perceived as interacting objects and their repulsion may be modelled by a sort of deterministic formulation. Risk due to tankers running aground addresses an approach fairway to an oil terminal in Sköldvik, near Helsinki. The consequences of an accident are expressed in monetary terms, and concern costs of an oil spill, based on statistics of compensations claimed from the International Oil Pollution Compensation Funds (IOPC Funds) by parties involved.

  18. FY2017 Updates to the SAS4A/SASSYS-1 Safety Analysis Code

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fanning, T. H.

    The SAS4A/SASSYS-1 safety analysis software is used to perform deterministic analysis of anticipated events as well as design-basis and beyond-design-basis accidents for advanced fast reactors. It plays a central role in the analysis of U.S. DOE conceptual designs, proposed test and demonstration reactors, and in domestic and international collaborations. This report summarizes the code development activities that have taken place during FY2017. Extensions to the void and cladding reactivity feedback models have been implemented, and Control System capabilities have been improved through a new virtual data acquisition system for plant state variables and an additional Block Signal for a variablemore » lag compensator to represent reactivity feedback for novel shutdown devices. Current code development and maintenance needs are also summarized in three key areas: software quality assurance, modeling improvements, and maintenance of related tools. With ongoing support, SAS4A/SASSYS-1 can continue to fulfill its growing role in fast reactor safety analysis and help solidify DOE’s leadership role in fast reactor safety both domestically and in international collaborations.« less

  19. An approach to model reactor core nodalization for deterministic safety analysis

    NASA Astrophysics Data System (ADS)

    Salim, Mohd Faiz; Samsudin, Mohd Rafie; Mamat @ Ibrahim, Mohd Rizal; Roslan, Ridha; Sadri, Abd Aziz; Farid, Mohd Fairus Abd

    2016-01-01

    Adopting good nodalization strategy is essential to produce an accurate and high quality input model for Deterministic Safety Analysis (DSA) using System Thermal-Hydraulic (SYS-TH) computer code. The purpose of such analysis is to demonstrate the compliance against regulatory requirements and to verify the behavior of the reactor during normal and accident conditions as it was originally designed. Numerous studies in the past have been devoted to the development of the nodalization strategy for small research reactor (e.g. 250kW) up to the bigger research reactor (e.g. 30MW). As such, this paper aims to discuss the state-of-arts thermal hydraulics channel to be employed in the nodalization for RTP-TRIGA Research Reactor specifically for the reactor core. At present, the required thermal-hydraulic parameters for reactor core, such as core geometrical data (length, coolant flow area, hydraulic diameters, and axial power profile) and material properties (including the UZrH1.6, stainless steel clad, graphite reflector) have been collected, analyzed and consolidated in the Reference Database of RTP using standardized methodology, mainly derived from the available technical documentations. Based on the available information in the database, assumptions made on the nodalization approach and calculations performed will be discussed and presented. The development and identification of the thermal hydraulics channel for the reactor core will be implemented during the SYS-TH calculation using RELAP5-3D® computer code. This activity presented in this paper is part of the development of overall nodalization description for RTP-TRIGA Research Reactor under the IAEA Norwegian Extra-Budgetary Programme (NOKEBP) mentoring project on Expertise Development through the Analysis of Reactor Thermal-Hydraulics for Malaysia, denoted as EARTH-M.

  20. An approach to model reactor core nodalization for deterministic safety analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Salim, Mohd Faiz, E-mail: mohdfaizs@tnb.com.my; Samsudin, Mohd Rafie, E-mail: rafies@tnb.com.my; Mamat Ibrahim, Mohd Rizal, E-mail: m-rizal@nuclearmalaysia.gov.my

    Adopting good nodalization strategy is essential to produce an accurate and high quality input model for Deterministic Safety Analysis (DSA) using System Thermal-Hydraulic (SYS-TH) computer code. The purpose of such analysis is to demonstrate the compliance against regulatory requirements and to verify the behavior of the reactor during normal and accident conditions as it was originally designed. Numerous studies in the past have been devoted to the development of the nodalization strategy for small research reactor (e.g. 250kW) up to the bigger research reactor (e.g. 30MW). As such, this paper aims to discuss the state-of-arts thermal hydraulics channel to bemore » employed in the nodalization for RTP-TRIGA Research Reactor specifically for the reactor core. At present, the required thermal-hydraulic parameters for reactor core, such as core geometrical data (length, coolant flow area, hydraulic diameters, and axial power profile) and material properties (including the UZrH{sub 1.6}, stainless steel clad, graphite reflector) have been collected, analyzed and consolidated in the Reference Database of RTP using standardized methodology, mainly derived from the available technical documentations. Based on the available information in the database, assumptions made on the nodalization approach and calculations performed will be discussed and presented. The development and identification of the thermal hydraulics channel for the reactor core will be implemented during the SYS-TH calculation using RELAP5-3D{sup ®} computer code. This activity presented in this paper is part of the development of overall nodalization description for RTP-TRIGA Research Reactor under the IAEA Norwegian Extra-Budgetary Programme (NOKEBP) mentoring project on Expertise Development through the Analysis of Reactor Thermal-Hydraulics for Malaysia, denoted as EARTH-M.« less

  1. Deterministic and Stochastic Analysis of a Prey-Dependent Predator-Prey System

    ERIC Educational Resources Information Center

    Maiti, Alakes; Samanta, G. P.

    2005-01-01

    This paper reports on studies of the deterministic and stochastic behaviours of a predator-prey system with prey-dependent response function. The first part of the paper deals with the deterministic analysis of uniform boundedness, permanence, stability and bifurcation. In the second part the reproductive and mortality factors of the prey and…

  2. Probability and Locality: Determinism Versus Indeterminism in Quantum Mechanics

    NASA Astrophysics Data System (ADS)

    Dickson, William Michael

    1995-01-01

    Quantum mechanics is often taken to be necessarily probabilistic. However, this view of quantum mechanics appears to be more the result of historical accident than of careful analysis. Moreover, quantum mechanics in its usual form faces serious problems. Although the mathematical core of quantum mechanics--quantum probability theory- -does not face conceptual difficulties, the application of quantum probability to the physical world leads to problems. In particular, quantum mechanics seems incapable of describing our everyday macroscopic experience. Therefore, several authors have proposed new interpretations --including (but not limited to) modal interpretations, spontaneous localization interpretations, the consistent histories approach, and the Bohm theory--each of which deals with quantum-mechanical probabilities differently. Each of these interpretations promises to describe our macroscopic experience and, arguably, each succeeds. Is there any way to compare them? Perhaps, if we turn to another troubling aspect of quantum mechanics, non-locality. Non -locality is troubling because prima facie it threatens the compatibility of quantum mechanics with special relativity. This prima facie threat is mitigated by the no-signalling theorems in quantum mechanics, but nonetheless one may find a 'conflict of spirit' between nonlocality in quantum mechanics and special relativity. Do any of these interpretations resolve this conflict of spirit?. There is a strong relation between how an interpretation deals with quantum-mechanical probabilities and how it deals with non-locality. The main argument here is that only a completely deterministic interpretation can be completely local. That is, locality together with the empirical predictions of quantum mechanics (specifically, its strict correlations) entails determinism. But even with this entailment in hand, comparison of the various interpretations requires a look at each, to see how non-locality arises, or in the case of deterministic interpretations, whether it arises. The result of this investigation is that, at the least, deterministic interpretations are no worse off with respect to special relativity than indeterministic interpretations. This conclusion runs against a common view that deterministic interpretations, specifically the Bohm theory, have more difficulty with special relativity than other interpretations.

  3. Ensemble Simulation of the Atmospheric Radionuclides Discharged by the Fukushima Nuclear Accident

    NASA Astrophysics Data System (ADS)

    Sekiyama, Thomas; Kajino, Mizuo; Kunii, Masaru

    2013-04-01

    Enormous amounts of radionuclides were discharged into the atmosphere by a nuclear accident at the Fukushima Daiichi nuclear power plant (FDNPP) after the earthquake and tsunami on 11 March 2011. The radionuclides were dispersed from the power plant and deposited mainly over eastern Japan and the North Pacific Ocean. A lot of numerical simulations of the radionuclide dispersion and deposition had been attempted repeatedly since the nuclear accident. However, none of them were able to perfectly simulate the distribution of dose rates observed after the accident over eastern Japan. This was partly due to the error of the wind vectors and precipitations used in the numerical simulations; unfortunately, their deterministic simulations could not deal with the probability distribution of the simulation results and errors. Therefore, an ensemble simulation of the atmospheric radionuclides was performed using the ensemble Kalman filter (EnKF) data assimilation system coupled with the Japan Meteorological Agency (JMA) non-hydrostatic mesoscale model (NHM); this mesoscale model has been used operationally for daily weather forecasts by JMA. Meteorological observations were provided to the EnKF data assimilation system from the JMA operational-weather-forecast dataset. Through this ensemble data assimilation, twenty members of the meteorological analysis over eastern Japan from 11 to 31 March 2011 were successfully obtained. Using these meteorological ensemble analysis members, the radionuclide behavior in the atmosphere such as advection, convection, diffusion, dry deposition, and wet deposition was simulated. This ensemble simulation provided the multiple results of the radionuclide dispersion and distribution. Because a large ensemble deviation indicates the low accuracy of the numerical simulation, the probabilistic information is obtainable from the ensemble simulation results. For example, the uncertainty of precipitation triggered the uncertainty of wet deposition; the uncertainty of wet deposition triggered the uncertainty of atmospheric radionuclide amounts. Then the remained radionuclides were transported downwind; consequently the uncertainty signal of the radionuclide amounts was propagated downwind. The signal propagation was seen in the ensemble simulation by the tracking of the large deviation areas of radionuclide concentration and deposition. These statistics are able to provide information useful for the probabilistic prediction of radionuclides.

  4. Integrating stochastic time-dependent travel speed in solution methods for the dynamic dial-a-ride problem.

    PubMed

    Schilde, M; Doerner, K F; Hartl, R F

    2014-10-01

    In urban areas, logistic transportation operations often run into problems because travel speeds change, depending on the current traffic situation. If not accounted for, time-dependent and stochastic travel speeds frequently lead to missed time windows and thus poorer service. Especially in the case of passenger transportation, it often leads to excessive passenger ride times as well. Therefore, time-dependent and stochastic influences on travel speeds are relevant for finding feasible and reliable solutions. This study considers the effect of exploiting statistical information available about historical accidents, using stochastic solution approaches for the dynamic dial-a-ride problem (dynamic DARP). The authors propose two pairs of metaheuristic solution approaches, each consisting of a deterministic method (average time-dependent travel speeds for planning) and its corresponding stochastic version (exploiting stochastic information while planning). The results, using test instances with up to 762 requests based on a real-world road network, show that in certain conditions, exploiting stochastic information about travel speeds leads to significant improvements over deterministic approaches.

  5. A Comparison of Probabilistic and Deterministic Campaign Analysis for Human Space Exploration

    NASA Technical Reports Server (NTRS)

    Merrill, R. Gabe; Andraschko, Mark; Stromgren, Chel; Cirillo, Bill; Earle, Kevin; Goodliff, Kandyce

    2008-01-01

    Human space exploration is by its very nature an uncertain endeavor. Vehicle reliability, technology development risk, budgetary uncertainty, and launch uncertainty all contribute to stochasticity in an exploration scenario. However, traditional strategic analysis has been done in a deterministic manner, analyzing and optimizing the performance of a series of planned missions. History has shown that exploration scenarios rarely follow such a planned schedule. This paper describes a methodology to integrate deterministic and probabilistic analysis of scenarios in support of human space exploration. Probabilistic strategic analysis is used to simulate "possible" scenario outcomes, based upon the likelihood of occurrence of certain events and a set of pre-determined contingency rules. The results of the probabilistic analysis are compared to the nominal results from the deterministic analysis to evaluate the robustness of the scenario to adverse events and to test and optimize contingency planning.

  6. Current issues and actions in radiation protection of patients.

    PubMed

    Holmberg, Ola; Malone, Jim; Rehani, Madan; McLean, Donald; Czarwinski, Renate

    2010-10-01

    Medical application of ionizing radiation is a massive and increasing activity globally. While the use of ionizing radiation in medicine brings tremendous benefits to the global population, the associated risks due to stochastic and deterministic effects make it necessary to protect patients from potential harm. Current issues in radiation protection of patients include not only the rapidly increasing collective dose to the global population from medical exposure, but also that a substantial percentage of diagnostic imaging examinations are unnecessary, and the cumulative dose to individuals from medical exposure is growing. In addition to this, continued reports on deterministic injuries from safety related events in the medical use of ionizing radiation are raising awareness on the necessity for accident prevention measures. The International Atomic Energy Agency is engaged in several activities to reverse the negative trends of these current issues, including improvement of the justification process, the tracking of radiation history of individual patients, shared learning of safety significant events, and the use of comprehensive quality audits in the clinical environment. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  7. Integrating stochastic time-dependent travel speed in solution methods for the dynamic dial-a-ride problem

    PubMed Central

    Schilde, M.; Doerner, K.F.; Hartl, R.F.

    2014-01-01

    In urban areas, logistic transportation operations often run into problems because travel speeds change, depending on the current traffic situation. If not accounted for, time-dependent and stochastic travel speeds frequently lead to missed time windows and thus poorer service. Especially in the case of passenger transportation, it often leads to excessive passenger ride times as well. Therefore, time-dependent and stochastic influences on travel speeds are relevant for finding feasible and reliable solutions. This study considers the effect of exploiting statistical information available about historical accidents, using stochastic solution approaches for the dynamic dial-a-ride problem (dynamic DARP). The authors propose two pairs of metaheuristic solution approaches, each consisting of a deterministic method (average time-dependent travel speeds for planning) and its corresponding stochastic version (exploiting stochastic information while planning). The results, using test instances with up to 762 requests based on a real-world road network, show that in certain conditions, exploiting stochastic information about travel speeds leads to significant improvements over deterministic approaches. PMID:25844013

  8. Stability analysis of multi-group deterministic and stochastic epidemic models with vaccination rate

    NASA Astrophysics Data System (ADS)

    Wang, Zhi-Gang; Gao, Rui-Mei; Fan, Xiao-Ming; Han, Qi-Xing

    2014-09-01

    We discuss in this paper a deterministic multi-group MSIR epidemic model with a vaccination rate, the basic reproduction number ℛ0, a key parameter in epidemiology, is a threshold which determines the persistence or extinction of the disease. By using Lyapunov function techniques, we show if ℛ0 is greater than 1 and the deterministic model obeys some conditions, then the disease will prevail, the infective persists and the endemic state is asymptotically stable in a feasible region. If ℛ0 is less than or equal to 1, then the infective disappear so the disease dies out. In addition, stochastic noises around the endemic equilibrium will be added to the deterministic MSIR model in order that the deterministic model is extended to a system of stochastic ordinary differential equations. In the stochastic version, we carry out a detailed analysis on the asymptotic behavior of the stochastic model. In addition, regarding the value of ℛ0, when the stochastic system obeys some conditions and ℛ0 is greater than 1, we deduce the stochastic system is stochastically asymptotically stable. Finally, the deterministic and stochastic model dynamics are illustrated through computer simulations.

  9. A statistical approach to nuclear fuel design and performance

    NASA Astrophysics Data System (ADS)

    Cunning, Travis Andrew

    As CANDU fuel failures can have significant economic and operational consequences on the Canadian nuclear power industry, it is essential that factors impacting fuel performance are adequately understood. Current industrial practice relies on deterministic safety analysis and the highly conservative "limit of operating envelope" approach, where all parameters are assumed to be at their limits simultaneously. This results in a conservative prediction of event consequences with little consideration given to the high quality and precision of current manufacturing processes. This study employs a novel approach to the prediction of CANDU fuel reliability. Probability distributions are fitted to actual fuel manufacturing datasets provided by Cameco Fuel Manufacturing, Inc. They are used to form input for two industry-standard fuel performance codes: ELESTRES for the steady-state case and ELOCA for the transient case---a hypothesized 80% reactor outlet header break loss of coolant accident. Using a Monte Carlo technique for input generation, 105 independent trials are conducted and probability distributions are fitted to key model output quantities. Comparing model output against recognized industrial acceptance criteria, no fuel failures are predicted for either case. Output distributions are well removed from failure limit values, implying that margin exists in current fuel manufacturing and design. To validate the results and attempt to reduce the simulation burden of the methodology, two dimensional reduction methods are assessed. Using just 36 trials, both methods are able to produce output distributions that agree strongly with those obtained via the brute-force Monte Carlo method, often to a relative discrepancy of less than 0.3% when predicting the first statistical moment, and a relative discrepancy of less than 5% when predicting the second statistical moment. In terms of global sensitivity, pellet density proves to have the greatest impact on fuel performance, with an average sensitivity index of 48.93% on key output quantities. Pellet grain size and dish depth are also significant contributors, at 31.53% and 13.46%, respectively. A traditional limit of operating envelope case is also evaluated. This case produces output values that exceed the maximum values observed during the 105 Monte Carlo trials for all output quantities of interest. In many cases the difference between the predictions of the two methods is very prominent, and the highly conservative nature of the deterministic approach is demonstrated. A reliability analysis of CANDU fuel manufacturing parametric data, specifically pertaining to the quantification of fuel performance margins, has not been conducted previously. Key Words: CANDU, nuclear fuel, Cameco, fuel manufacturing, fuel modelling, fuel performance, fuel reliability, ELESTRES, ELOCA, dimensional reduction methods, global sensitivity analysis, deterministic safety analysis, probabilistic safety analysis.

  10. Developing techniques for cause-responsibility analysis of occupational accidents.

    PubMed

    Jabbari, Mousa; Ghorbani, Roghayeh

    2016-11-01

    The aim of this study was to specify the causes of occupational accidents, determine social responsibility and the role of groups involved in work-related accidents. This study develops occupational accidents causes tree, occupational accidents responsibility tree, and occupational accidents component-responsibility analysis worksheet; based on these methods, it develops cause-responsibility analysis (CRA) techniques, and for testing them, analyzes 100 fatal/disabling occupational accidents in the construction setting that were randomly selected from all the work-related accidents in Tehran, Iran, over a 5-year period (2010-2014). The main result of this study involves two techniques for CRA: occupational accidents tree analysis (OATA) and occupational accidents components analysis (OACA), used in parallel for determination of responsible groups and responsibilities rate. From the results, we find that the management group of construction projects has 74.65% responsibility of work-related accidents. The developed techniques are purposeful for occupational accidents investigation/analysis, especially for the determination of detailed list of tasks, responsibilities, and their rates. Therefore, it is useful for preventing work-related accidents by focusing on the responsible group's duties. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. An overview of engineering concepts and current design algorithms for probabilistic structural analysis

    NASA Technical Reports Server (NTRS)

    Duffy, S. F.; Hu, J.; Hopkins, D. A.

    1995-01-01

    The article begins by examining the fundamentals of traditional deterministic design philosophy. The initial section outlines the concepts of failure criteria and limit state functions two traditional notions that are embedded in deterministic design philosophy. This is followed by a discussion regarding safety factors (a possible limit state function) and the common utilization of statistical concepts in deterministic engineering design approaches. Next the fundamental aspects of a probabilistic failure analysis are explored and it is shown that deterministic design concepts mentioned in the initial portion of the article are embedded in probabilistic design methods. For components fabricated from ceramic materials (and other similarly brittle materials) the probabilistic design approach yields the widely used Weibull analysis after suitable assumptions are incorporated. The authors point out that Weibull analysis provides the rare instance where closed form solutions are available for a probabilistic failure analysis. Since numerical methods are usually required to evaluate component reliabilities, a section on Monte Carlo methods is included to introduce the concept. The article concludes with a presentation of the technical aspects that support the numerical method known as fast probability integration (FPI). This includes a discussion of the Hasofer-Lind and Rackwitz-Fiessler approximations.

  12. Using stochastic models to incorporate spatial and temporal variability [Exercise 14

    Treesearch

    Carolyn Hull Sieg; Rudy M. King; Fred Van Dyke

    2003-01-01

    To this point, our analysis of population processes and viability in the western prairie fringed orchid has used only deterministic models. In this exercise, we conduct a similar analysis, using a stochastic model instead. This distinction is of great importance to population biology in general and to conservation biology in particular. In deterministic models,...

  13. Tularosa Basin Play Fairway Analysis Data and Models

    DOE Data Explorer

    Nash, Greg

    2017-07-11

    This submission includes raster datasets for each layer of evidence used for weights of evidence analysis as well as the deterministic play fairway analysis (PFA). Data representative of heat, permeability and groundwater comprises some of the raster datasets. Additionally, the final deterministic PFA model is provided along with a certainty model. All of these datasets are best used with an ArcGIS software package, specifically Spatial Data Modeler.

  14. Criticality Calculations with MCNP6 - Practical Lectures

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Brown, Forrest B.; Rising, Michael Evan; Alwin, Jennifer Louise

    2016-11-29

    These slides are used to teach MCNP (Monte Carlo N-Particle) usage to nuclear criticality safety analysts. The following are the lecture topics: course information, introduction, MCNP basics, criticality calculations, advanced geometry, tallies, adjoint-weighted tallies and sensitivities, physics and nuclear data, parameter studies, NCS validation I, NCS validation II, NCS validation III, case study 1 - solution tanks, case study 2 - fuel vault, case study 3 - B&W core, case study 4 - simple TRIGA, case study 5 - fissile mat. vault, criticality accident alarm systems. After completion of this course, you should be able to: Develop an input modelmore » for MCNP; Describe how cross section data impact Monte Carlo and deterministic codes; Describe the importance of validation of computer codes and how it is accomplished; Describe the methodology supporting Monte Carlo codes and deterministic codes; Describe pitfalls of Monte Carlo calculations; Discuss the strengths and weaknesses of Monte Carlo and Discrete Ordinants codes; The diffusion theory model is not strictly valid for treating fissile systems in which neutron absorption, voids, and/or material boundaries are present. In the context of these limitations, identify a fissile system for which a diffusion theory solution would be adequate.« less

  15. Selective Shielding of Bone Marrow: An Approach to Protecting Humans from External Gamma Radiation.

    PubMed

    Waterman, Gideon; Kase, Kenneth; Orion, Itzhak; Broisman, Andrey; Milstein, Oren

    2017-09-01

    The current feasibility of protecting emergency responders through bone marrow selective shielding is highlighted in the recent OECD/NEA report on severe accident management. Until recently, there was no effective personal protection from externally penetrating gamma radiation. In Chernobyl, first-responders wore makeshift lead sheeting, whereas in Fukushima protective equipment from gamma radiation was not available. Older protective solutions that use thin layers of shielding over large body surfaces are ineffective for energetic gamma radiation. Acute exposures may result in Acute Radiation Syndrome where the survival-limiting factor up to 10 Gy uniform, homogeneous exposure is irreversible bone marrow damage. Protracted, lower exposures may result in malignancies of which bone marrow is especially susceptible, being compounded by leukemia's short latency time. This highlights the importance of shielding bone marrow for preventing both deterministic and stochastic effects. Due to the extraordinary regenerative potential of hematopoietic stem cells, to effectively prevent the deterministic effects of bone marrow exposure, it is sufficient to protect only a small fraction of this tissue. This biological principle allows for a new class of equipment providing unprecedented attenuation of radiation to select marrow-rich regions, deferring the hematopoietic sub-syndrome of Acute Radiation Syndrome to much higher doses. As approximately half of the body's active bone marrow resides within the pelvis region, shielding this area holds great promise for preventing the deterministic effects of bone marrow exposure and concomitantly reducing stochastic effects. The efficacy of a device that selectively shields this region and other radiosensitive organs in the abdominal area is shown here.

  16. Major Accidents (Gray Swans) Likelihood Modeling Using Accident Precursors and Approximate Reasoning.

    PubMed

    Khakzad, Nima; Khan, Faisal; Amyotte, Paul

    2015-07-01

    Compared to the remarkable progress in risk analysis of normal accidents, the risk analysis of major accidents has not been so well-established, partly due to the complexity of such accidents and partly due to low probabilities involved. The issue of low probabilities normally arises from the scarcity of major accidents' relevant data since such accidents are few and far between. In this work, knowing that major accidents are frequently preceded by accident precursors, a novel precursor-based methodology has been developed for likelihood modeling of major accidents in critical infrastructures based on a unique combination of accident precursor data, information theory, and approximate reasoning. For this purpose, we have introduced an innovative application of information analysis to identify the most informative near accident of a major accident. The observed data of the near accident were then used to establish predictive scenarios to foresee the occurrence of the major accident. We verified the methodology using offshore blowouts in the Gulf of Mexico, and then demonstrated its application to dam breaches in the United Sates. © 2015 Society for Risk Analysis.

  17. Full 3D visualization tool-kit for Monte Carlo and deterministic transport codes

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Frambati, S.; Frignani, M.

    2012-07-01

    We propose a package of tools capable of translating the geometric inputs and outputs of many Monte Carlo and deterministic radiation transport codes into open source file formats. These tools are aimed at bridging the gap between trusted, widely-used radiation analysis codes and very powerful, more recent and commonly used visualization software, thus supporting the design process and helping with shielding optimization. Three main lines of development were followed: mesh-based analysis of Monte Carlo codes, mesh-based analysis of deterministic codes and Monte Carlo surface meshing. The developed kit is considered a powerful and cost-effective tool in the computer-aided design formore » radiation transport code users of the nuclear world, and in particular in the fields of core design and radiation analysis. (authors)« less

  18. Validity and consistency assessment of accident analysis methods in the petroleum industry.

    PubMed

    Ahmadi, Omran; Mortazavi, Seyed Bagher; Khavanin, Ali; Mokarami, Hamidreza

    2017-11-17

    Accident analysis is the main aspect of accident investigation. It includes the method of connecting different causes in a procedural way. Therefore, it is important to use valid and reliable methods for the investigation of different causal factors of accidents, especially the noteworthy ones. This study aimed to prominently assess the accuracy (sensitivity index [SI]) and consistency of the six most commonly used accident analysis methods in the petroleum industry. In order to evaluate the methods of accident analysis, two real case studies (process safety and personal accident) from the petroleum industry were analyzed by 10 assessors. The accuracy and consistency of these methods were then evaluated. The assessors were trained in the workshop of accident analysis methods. The systematic cause analysis technique and bowtie methods gained the greatest SI scores for both personal and process safety accidents, respectively. The best average results of the consistency in a single method (based on 10 independent assessors) were in the region of 70%. This study confirmed that the application of methods with pre-defined causes and a logic tree could enhance the sensitivity and consistency of accident analysis.

  19. Joint release rate estimation and measurement-by-measurement model correction for atmospheric radionuclide emission in nuclear accidents: An application to wind tunnel experiments.

    PubMed

    Li, Xinpeng; Li, Hong; Liu, Yun; Xiong, Wei; Fang, Sheng

    2018-03-05

    The release rate of atmospheric radionuclide emissions is a critical factor in the emergency response to nuclear accidents. However, there are unavoidable biases in radionuclide transport models, leading to inaccurate estimates. In this study, a method that simultaneously corrects these biases and estimates the release rate is developed. Our approach provides a more complete measurement-by-measurement correction of the biases with a coefficient matrix that considers both deterministic and stochastic deviations. This matrix and the release rate are jointly solved by the alternating minimization algorithm. The proposed method is generic because it does not rely on specific features of transport models or scenarios. It is validated against wind tunnel experiments that simulate accidental releases in a heterogonous and densely built nuclear power plant site. The sensitivities to the position, number, and quality of measurements and extendibility of the method are also investigated. The results demonstrate that this method effectively corrects the model biases, and therefore outperforms Tikhonov's method in both release rate estimation and model prediction. The proposed approach is robust to uncertainties and extendible with various center estimators, thus providing a flexible framework for robust source inversion in real accidents, even if large uncertainties exist in multiple factors. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Discrete-Time Deterministic $Q$ -Learning: A Novel Convergence Analysis.

    PubMed

    Wei, Qinglai; Lewis, Frank L; Sun, Qiuye; Yan, Pengfei; Song, Ruizhuo

    2017-05-01

    In this paper, a novel discrete-time deterministic Q -learning algorithm is developed. In each iteration of the developed Q -learning algorithm, the iterative Q function is updated for all the state and control spaces, instead of updating for a single state and a single control in traditional Q -learning algorithm. A new convergence criterion is established to guarantee that the iterative Q function converges to the optimum, where the convergence criterion of the learning rates for traditional Q -learning algorithms is simplified. During the convergence analysis, the upper and lower bounds of the iterative Q function are analyzed to obtain the convergence criterion, instead of analyzing the iterative Q function itself. For convenience of analysis, the convergence properties for undiscounted case of the deterministic Q -learning algorithm are first developed. Then, considering the discounted factor, the convergence criterion for the discounted case is established. Neural networks are used to approximate the iterative Q function and compute the iterative control law, respectively, for facilitating the implementation of the deterministic Q -learning algorithm. Finally, simulation results and comparisons are given to illustrate the performance of the developed algorithm.

  1. NASA-STD-7009 Guidance Document for Human Health and Performance Models and Simulations

    NASA Technical Reports Server (NTRS)

    Walton, Marlei; Mulugeta, Lealem; Nelson, Emily S.; Myers, Jerry G.

    2014-01-01

    Rigorous verification, validation, and credibility (VVC) processes are imperative to ensure that models and simulations (MS) are sufficiently reliable to address issues within their intended scope. The NASA standard for MS, NASA-STD-7009 (7009) [1] was a resultant outcome of the Columbia Accident Investigation Board (CAIB) to ensure MS are developed, applied, and interpreted appropriately for making decisions that may impact crew or mission safety. Because the 7009 focus is engineering systems, a NASA-STD-7009 Guidance Document is being developed to augment the 7009 and provide information, tools, and techniques applicable to the probabilistic and deterministic biological MS more prevalent in human health and performance (HHP) and space biomedical research and operations.

  2. Deterministic and stochastic CTMC models from Zika disease transmission

    NASA Astrophysics Data System (ADS)

    Zevika, Mona; Soewono, Edy

    2018-03-01

    Zika infection is one of the most important mosquito-borne diseases in the world. Zika virus (ZIKV) is transmitted by many Aedes-type mosquitoes including Aedes aegypti. Pregnant women with the Zika virus are at risk of having a fetus or infant with a congenital defect and suffering from microcephaly. Here, we formulate a Zika disease transmission model using two approaches, a deterministic model and a continuous-time Markov chain stochastic model. The basic reproduction ratio is constructed from a deterministic model. Meanwhile, the CTMC stochastic model yields an estimate of the probability of extinction and outbreaks of Zika disease. Dynamical simulations and analysis of the disease transmission are shown for the deterministic and stochastic models.

  3. Distinguishing between stochasticity and determinism: Examples from cell cycle duration variability.

    PubMed

    Pearl Mizrahi, Sivan; Sandler, Oded; Lande-Diner, Laura; Balaban, Nathalie Q; Simon, Itamar

    2016-01-01

    We describe a recent approach for distinguishing between stochastic and deterministic sources of variability, focusing on the mammalian cell cycle. Variability between cells is often attributed to stochastic noise, although it may be generated by deterministic components. Interestingly, lineage information can be used to distinguish between variability and determinism. Analysis of correlations within a lineage of the mammalian cell cycle duration revealed its deterministic nature. Here, we discuss the sources of such variability and the possibility that the underlying deterministic process is due to the circadian clock. Finally, we discuss the "kicked cell cycle" model and its implication on the study of the cell cycle in healthy and cancerous tissues. © 2015 WILEY Periodicals, Inc.

  4. Airline Safety Improvement Through Experience with Near-Misses: A Cautionary Tale.

    PubMed

    Madsen, Peter; Dillon, Robin L; Tinsley, Catherine H

    2016-05-01

    In recent years, the U.S. commercial airline industry has achieved unprecedented levels of safety, with the statistical risk associated with U.S. commercial aviation falling to 0.003 fatalities per 100 million passengers. But decades of research on organizational learning show that success often breeds complacency and failure inspires improvement. With accidents as rare events, can the airline industry continue safety advancements? This question is complicated by the complex system in which the industry operates where chance combinations of multiple factors contribute to what are largely probabilistic (rather than deterministic) outcomes. Thus, some apparent successes are realized because of good fortune rather than good processes, and this research intends to bring attention to these events, the near-misses. The processes that create these near-misses could pose a threat if multiple contributing factors combine in adverse ways without the intervention of good fortune. Yet, near-misses (if recognized as such) can, theoretically, offer a mechanism for continuing safety improvements, above and beyond learning gleaned from observable failure. We test whether or not this learning is apparent in the airline industry. Using data from 1990 to 2007, fixed effects Poisson regressions show that airlines learn from accidents (their own and others), and from one category of near-misses-those where the possible dangers are salient. Unfortunately, airlines do not improve following near-miss incidents when the focal event has no clear warnings of significant danger. Therefore, while airlines need to and can learn from certain near-misses, we conclude with recommendations for improving airline learning from all near-misses. © 2015 Society for Risk Analysis.

  5. Expansion or extinction: deterministic and stochastic two-patch models with Allee effects.

    PubMed

    Kang, Yun; Lanchier, Nicolas

    2011-06-01

    We investigate the impact of Allee effect and dispersal on the long-term evolution of a population in a patchy environment. Our main focus is on whether a population already established in one patch either successfully invades an adjacent empty patch or undergoes a global extinction. Our study is based on the combination of analytical and numerical results for both a deterministic two-patch model and a stochastic counterpart. The deterministic model has either two, three or four attractors. The existence of a regime with exactly three attractors only appears when patches have distinct Allee thresholds. In the presence of weak dispersal, the analysis of the deterministic model shows that a high-density and a low-density populations can coexist at equilibrium in nearby patches, whereas the analysis of the stochastic model indicates that this equilibrium is metastable, thus leading after a large random time to either a global expansion or a global extinction. Up to some critical dispersal, increasing the intensity of the interactions leads to an increase of both the basin of attraction of the global extinction and the basin of attraction of the global expansion. Above this threshold, for both the deterministic and the stochastic models, the patches tend to synchronize as the intensity of the dispersal increases. This results in either a global expansion or a global extinction. For the deterministic model, there are only two attractors, while the stochastic model no longer exhibits a metastable behavior. In the presence of strong dispersal, the limiting behavior is entirely determined by the value of the Allee thresholds as the global population size in the deterministic and the stochastic models evolves as dictated by their single-patch counterparts. For all values of the dispersal parameter, Allee effects promote global extinction in terms of an expansion of the basin of attraction of the extinction equilibrium for the deterministic model and an increase of the probability of extinction for the stochastic model.

  6. Cognitive Diagnostic Analysis Using Hierarchically Structured Skills

    ERIC Educational Resources Information Center

    Su, Yu-Lan

    2013-01-01

    This dissertation proposes two modified cognitive diagnostic models (CDMs), the deterministic, inputs, noisy, "and" gate with hierarchy (DINA-H) model and the deterministic, inputs, noisy, "or" gate with hierarchy (DINO-H) model. Both models incorporate the hierarchical structures of the cognitive skills in the model estimation…

  7. Multi-Hazard Advanced Seismic Probabilistic Risk Assessment Tools and Applications

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Coleman, Justin L.; Bolisetti, Chandu; Veeraraghavan, Swetha

    Design of nuclear power plant (NPP) facilities to resist natural hazards has been a part of the regulatory process from the beginning of the NPP industry in the United States (US), but has evolved substantially over time. The original set of approaches and methods was entirely deterministic in nature and focused on a traditional engineering margins-based approach. However, over time probabilistic and risk-informed approaches were also developed and implemented in US Nuclear Regulatory Commission (NRC) guidance and regulation. A defense-in-depth framework has also been incorporated into US regulatory guidance over time. As a result, today, the US regulatory framework incorporatesmore » deterministic and probabilistic approaches for a range of different applications and for a range of natural hazard considerations. This framework will continue to evolve as a result of improved knowledge and newly identified regulatory needs and objectives, most notably in response to the NRC activities developed in response to the 2011 Fukushima accident in Japan. Although the US regulatory framework has continued to evolve over time, the tools, methods and data available to the US nuclear industry to meet the changing requirements have not kept pace. Notably, there is significant room for improvement in the tools and methods available for external event probabilistic risk assessment (PRA), which is the principal assessment approach used in risk-informed regulations and risk-informed decision-making applied to natural hazard assessment and design. This is particularly true if PRA is applied to natural hazards other than seismic loading. Development of a new set of tools and methods that incorporate current knowledge, modern best practice, and state-of-the-art computational resources would lead to more reliable assessment of facility risk and risk insights (e.g., the SSCs and accident sequences that are most risk-significant), with less uncertainty and reduced conservatisms.« less

  8. Estimating the epidemic threshold on networks by deterministic connections

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Li, Kezan, E-mail: lkzzr@sohu.com; Zhu, Guanghu; Fu, Xinchu

    2014-12-15

    For many epidemic networks some connections between nodes are treated as deterministic, while the remainder are random and have different connection probabilities. By applying spectral analysis to several constructed models, we find that one can estimate the epidemic thresholds of these networks by investigating information from only the deterministic connections. Nonetheless, in these models, generic nonuniform stochastic connections and heterogeneous community structure are also considered. The estimation of epidemic thresholds is achieved via inequalities with upper and lower bounds, which are found to be in very good agreement with numerical simulations. Since these deterministic connections are easier to detect thanmore » those stochastic connections, this work provides a feasible and effective method to estimate the epidemic thresholds in real epidemic networks.« less

  9. Probabilistic Finite Element Analysis & Design Optimization for Structural Designs

    NASA Astrophysics Data System (ADS)

    Deivanayagam, Arumugam

    This study focuses on implementing probabilistic nature of material properties (Kevlar® 49) to the existing deterministic finite element analysis (FEA) of fabric based engine containment system through Monte Carlo simulations (MCS) and implementation of probabilistic analysis in engineering designs through Reliability Based Design Optimization (RBDO). First, the emphasis is on experimental data analysis focusing on probabilistic distribution models which characterize the randomness associated with the experimental data. The material properties of Kevlar® 49 are modeled using experimental data analysis and implemented along with an existing spiral modeling scheme (SMS) and user defined constitutive model (UMAT) for fabric based engine containment simulations in LS-DYNA. MCS of the model are performed to observe the failure pattern and exit velocities of the models. Then the solutions are compared with NASA experimental tests and deterministic results. MCS with probabilistic material data give a good prospective on results rather than a single deterministic simulation results. The next part of research is to implement the probabilistic material properties in engineering designs. The main aim of structural design is to obtain optimal solutions. In any case, in a deterministic optimization problem even though the structures are cost effective, it becomes highly unreliable if the uncertainty that may be associated with the system (material properties, loading etc.) is not represented or considered in the solution process. Reliable and optimal solution can be obtained by performing reliability optimization along with the deterministic optimization, which is RBDO. In RBDO problem formulation, in addition to structural performance constraints, reliability constraints are also considered. This part of research starts with introduction to reliability analysis such as first order reliability analysis, second order reliability analysis followed by simulation technique that are performed to obtain probability of failure and reliability of structures. Next, decoupled RBDO procedure is proposed with a new reliability analysis formulation with sensitivity analysis, which is performed to remove the highly reliable constraints in the RBDO, thereby reducing the computational time and function evaluations. Followed by implementation of the reliability analysis concepts and RBDO in finite element 2D truss problems and a planar beam problem are presented and discussed.

  10. Applying STAMP in Accident Analysis

    NASA Technical Reports Server (NTRS)

    Leveson, Nancy; Daouk, Mirna; Dulac, Nicolas; Marais, Karen

    2003-01-01

    Accident models play a critical role in accident investigation and analysis. Most traditional models are based on an underlying chain of events. These models, however, have serious limitations when used for complex, socio-technical systems. Previously, Leveson proposed a new accident model (STAMP) based on system theory. In STAMP, the basic concept is not an event but a constraint. This paper shows how STAMP can be applied to accident analysis using three different views or models of the accident process and proposes a notation for describing this process.

  11. Flow injection analysis simulations and diffusion coefficient determination by stochastic and deterministic optimization methods.

    PubMed

    Kucza, Witold

    2013-07-25

    Stochastic and deterministic simulations of dispersion in cylindrical channels on the Poiseuille flow have been presented. The random walk (stochastic) and the uniform dispersion (deterministic) models have been used for computations of flow injection analysis responses. These methods coupled with the genetic algorithm and the Levenberg-Marquardt optimization methods, respectively, have been applied for determination of diffusion coefficients. The diffusion coefficients of fluorescein sodium, potassium hexacyanoferrate and potassium dichromate have been determined by means of the presented methods and FIA responses that are available in literature. The best-fit results agree with each other and with experimental data thus validating both presented approaches. Copyright © 2013 The Author. Published by Elsevier B.V. All rights reserved.

  12. Single pilot IFR accident data analysis

    NASA Technical Reports Server (NTRS)

    Harris, D. F.

    1983-01-01

    The aircraft accident data recorded by the National Transportation and Safety Board (NTSR) for 1964-1979 were analyzed to determine what problems exist in the general aviation (GA) single pilot instrument flight rule (SPIFR) environment. A previous study conducted in 1978 for the years 1964-1975 provided a basis for comparison. This effort was generally limited to SPIFR pilot error landing phase accidents but includes some SPIFR takeoff and enroute accident analysis as well as some dual pilot IFR accident analysis for comparison. Analysis was performed for 554 accidents of which 39% (216) occurred during the years 1976-1979.

  13. Civil helicopter wire strike assessment study. Volume 2: Accident analysis briefs

    NASA Technical Reports Server (NTRS)

    Tuomela, C. H.; Brennan, M. F.

    1980-01-01

    A description and analysis of each of the 208 civil helicopter wire strike accidents reported to the National Transportation Safety Board (NTSB) for the ten year period 1970-1979 is given. The accident analysis briefs were based on pilot reports, FAA investigation reports, and such accident photographs as were made available. Briefs were grouped by year and, within year, by NTSB accident report number.

  14. Counterfactual Quantum Deterministic Key Distribution

    NASA Astrophysics Data System (ADS)

    Zhang, Sheng; Wang, Jian; Tang, Chao-Jing

    2013-01-01

    We propose a new counterfactual quantum cryptography protocol concerning about distributing a deterministic key. By adding a controlled blocking operation module to the original protocol [T.G. Noh, Phys. Rev. Lett. 103 (2009) 230501], the correlation between the polarizations of the two parties, Alice and Bob, is extended, therefore, one can distribute both deterministic keys and random ones using our protocol. We have also given a simple proof of the security of our protocol using the technique we ever applied to the original protocol. Most importantly, our analysis produces a bound tighter than the existing ones.

  15. Deterministic blade row interactions in a centrifugal compressor stage

    NASA Technical Reports Server (NTRS)

    Kirtley, K. R.; Beach, T. A.

    1991-01-01

    The three-dimensional viscous flow in a low speed centrifugal compressor stage is simulated using an average passage Navier-Stokes analysis. The impeller discharge flow is of the jet/wake type with low momentum fluid in the shroud-pressure side corner coincident with the tip leakage vortex. This nonuniformity introduces periodic unsteadiness in the vane frame of reference. The effect of such deterministic unsteadiness on the time-mean is included in the analysis through the average passage stress, which allows the analysis of blade row interactions. The magnitude of the divergence of the deterministic unsteady stress is of the order of the divergence of the Reynolds stress over most of the span, from the impeller trailing edge to the vane throat. Although the potential effects on the blade trailing edge from the diffuser vane are small, strong secondary flows generated by the impeller degrade the performance of the diffuser vanes.

  16. Prediction accident triangle in maintenance of underground mine facilities using Poisson distribution analysis

    NASA Astrophysics Data System (ADS)

    Khuluqi, M. H.; Prapdito, R. R.; Sambodo, F. P.

    2018-04-01

    In Indonesia, mining is categorized as a hazardous industry. In recent years, a dramatic increase of mining equipment and technological complexities had resulted in higher maintenance expectations that accompanied by the changes in the working conditions, especially on safety. Ensuring safety during the process of conducting maintenance works in underground mine is important as an integral part of accident prevention programs. Accident triangle has provided a support to safety practitioner to draw a road map in preventing accidents. Poisson distribution is appropriate for the analysis of accidents at a specific site in a given time period. Based on the analysis of accident statistics in the underground mine maintenance of PT. Freeport Indonesia from 2011 through 2016, it is found that 12 minor accidents for 1 major accident and 66 equipment damages for 1 major accident as a new value of accident triangle. The result can be used for the future need for improving the accident prevention programs.

  17. Disentangling Mechanisms That Mediate the Balance Between Stochastic and Deterministic Processes in Microbial Succession

    DOE PAGES

    Dini-Andreote, Francisco; Stegen, James C.; van Elsas, Jan D.; ...

    2015-03-17

    Despite growing recognition that deterministic and stochastic factors simultaneously influence bacterial communities, little is known about mechanisms shifting their relative importance. To better understand underlying mechanisms, we developed a conceptual model linking ecosystem development during primary succession to shifts in the stochastic/deterministic balance. To evaluate the conceptual model we coupled spatiotemporal data on soil bacterial communities with environmental conditions spanning 105 years of salt marsh development. At the local scale there was a progression from stochasticity to determinism due to Na accumulation with increasing ecosystem age, supporting a main element of the conceptual model. At the regional-scale, soil organic mattermore » (SOM) governed the relative influence of stochasticity and the type of deterministic ecological selection, suggesting scale-dependency in how deterministic ecological selection is imposed. Analysis of a new ecological simulation model supported these conceptual inferences. Looking forward, we propose an extended conceptual model that integrates primary and secondary succession in microbial systems.« less

  18. An efficient deterministic-probabilistic approach to modeling regional groundwater flow: 2. Application to Owens Valley, California

    USGS Publications Warehouse

    Guymon, Gary L.; Yen, Chung-Cheng

    1990-01-01

    The applicability of a deterministic-probabilistic model for predicting water tables in southern Owens Valley, California, is evaluated. The model is based on a two-layer deterministic model that is cascaded with a two-point probability model. To reduce the potentially large number of uncertain variables in the deterministic model, lumping of uncertain variables was evaluated by sensitivity analysis to reduce the total number of uncertain variables to three variables: hydraulic conductivity, storage coefficient or specific yield, and source-sink function. Results demonstrate that lumping of uncertain parameters reduces computational effort while providing sufficient precision for the case studied. Simulated spatial coefficients of variation for water table temporal position in most of the basin is small, which suggests that deterministic models can predict water tables in these areas with good precision. However, in several important areas where pumping occurs or the geology is complex, the simulated spatial coefficients of variation are over estimated by the two-point probability method.

  19. An efficient deterministic-probabilistic approach to modeling regional groundwater flow: 2. Application to Owens Valley, California

    NASA Astrophysics Data System (ADS)

    Guymon, Gary L.; Yen, Chung-Cheng

    1990-07-01

    The applicability of a deterministic-probabilistic model for predicting water tables in southern Owens Valley, California, is evaluated. The model is based on a two-layer deterministic model that is cascaded with a two-point probability model. To reduce the potentially large number of uncertain variables in the deterministic model, lumping of uncertain variables was evaluated by sensitivity analysis to reduce the total number of uncertain variables to three variables: hydraulic conductivity, storage coefficient or specific yield, and source-sink function. Results demonstrate that lumping of uncertain parameters reduces computational effort while providing sufficient precision for the case studied. Simulated spatial coefficients of variation for water table temporal position in most of the basin is small, which suggests that deterministic models can predict water tables in these areas with good precision. However, in several important areas where pumping occurs or the geology is complex, the simulated spatial coefficients of variation are over estimated by the two-point probability method.

  20. Statistics of Delta v magnitude for a trajectory correction maneuver containing deterministic and random components

    NASA Technical Reports Server (NTRS)

    Bollman, W. E.; Chadwick, C.

    1982-01-01

    A number of interplanetary missions now being planned involve placing deterministic maneuvers along the flight path to alter the trajectory. Lee and Boain (1973) examined the statistics of trajectory correction maneuver (TCM) magnitude with no deterministic ('bias') component. The Delta v vector magnitude statistics were generated for several values of random Delta v standard deviations using expansions in terms of infinite hypergeometric series. The present investigation uses a different technique (Monte Carlo simulation) to generate Delta v magnitude statistics for a wider selection of random Delta v standard deviations and also extends the analysis to the case of nonzero deterministic Delta v's. These Delta v magnitude statistics are plotted parametrically. The plots are useful in assisting the analyst in quickly answering questions about the statistics of Delta v magnitude for single TCM's consisting of both a deterministic and a random component. The plots provide quick insight into the nature of the Delta v magnitude distribution for the TCM.

  1. The relationship between stochastic and deterministic quasi-steady state approximations.

    PubMed

    Kim, Jae Kyoung; Josić, Krešimir; Bennett, Matthew R

    2015-11-23

    The quasi steady-state approximation (QSSA) is frequently used to reduce deterministic models of biochemical networks. The resulting equations provide a simplified description of the network in terms of non-elementary reaction functions (e.g. Hill functions). Such deterministic reductions are frequently a basis for heuristic stochastic models in which non-elementary reaction functions are used to define reaction propensities. Despite their popularity, it remains unclear when such stochastic reductions are valid. It is frequently assumed that the stochastic reduction can be trusted whenever its deterministic counterpart is accurate. However, a number of recent examples show that this is not necessarily the case. Here we explain the origin of these discrepancies, and demonstrate a clear relationship between the accuracy of the deterministic and the stochastic QSSA for examples widely used in biological systems. With an analysis of a two-state promoter model, and numerical simulations for a variety of other models, we find that the stochastic QSSA is accurate whenever its deterministic counterpart provides an accurate approximation over a range of initial conditions which cover the likely fluctuations from the quasi steady-state (QSS). We conjecture that this relationship provides a simple and computationally inexpensive way to test the accuracy of reduced stochastic models using deterministic simulations. The stochastic QSSA is one of the most popular multi-scale stochastic simulation methods. While the use of QSSA, and the resulting non-elementary functions has been justified in the deterministic case, it is not clear when their stochastic counterparts are accurate. In this study, we show how the accuracy of the stochastic QSSA can be tested using their deterministic counterparts providing a concrete method to test when non-elementary rate functions can be used in stochastic simulations.

  2. A DETERMINISTIC GEOMETRIC REPRESENTATION OF TEMPORAL RAINFALL: SENSITIVITY ANALYSIS FOR A STORM IN BOSTON. (R824780)

    EPA Science Inventory

    In an earlier study, Puente and Obregón [Water Resour. Res. 32(1996)2825] reported on the usage of a deterministic fractal–multifractal (FM) methodology to faithfully describe an 8.3 h high-resolution rainfall time series in Boston, gathered every 15 s ...

  3. Categorizing accident sequences in the external radiotherapy for risk analysis

    PubMed Central

    2013-01-01

    Purpose This study identifies accident sequences from the past accidents in order to help the risk analysis application to the external radiotherapy. Materials and Methods This study reviews 59 accidental cases in two retrospective safety analyses that have collected the incidents in the external radiotherapy extensively. Two accident analysis reports that accumulated past incidents are investigated to identify accident sequences including initiating events, failure of safety measures, and consequences. This study classifies the accidents by the treatments stages and sources of errors for initiating events, types of failures in the safety measures, and types of undesirable consequences and the number of affected patients. Then, the accident sequences are grouped into several categories on the basis of similarity of progression. As a result, these cases can be categorized into 14 groups of accident sequence. Results The result indicates that risk analysis needs to pay attention to not only the planning stage, but also the calibration stage that is committed prior to the main treatment process. It also shows that human error is the largest contributor to initiating events as well as to the failure of safety measures. This study also illustrates an event tree analysis for an accident sequence initiated in the calibration. Conclusion This study is expected to provide sights into the accident sequences for the prospective risk analysis through the review of experiences. PMID:23865005

  4. A hybrid symplectic principal component analysis and central tendency measure method for detection of determinism in noisy time series with application to mechanomyography

    NASA Astrophysics Data System (ADS)

    Xie, Hong-Bo; Dokos, Socrates

    2013-06-01

    We present a hybrid symplectic geometry and central tendency measure (CTM) method for detection of determinism in noisy time series. CTM is effective for detecting determinism in short time series and has been applied in many areas of nonlinear analysis. However, its performance significantly degrades in the presence of strong noise. In order to circumvent this difficulty, we propose to use symplectic principal component analysis (SPCA), a new chaotic signal de-noising method, as the first step to recover the system dynamics. CTM is then applied to determine whether the time series arises from a stochastic process or has a deterministic component. Results from numerical experiments, ranging from six benchmark deterministic models to 1/f noise, suggest that the hybrid method can significantly improve detection of determinism in noisy time series by about 20 dB when the data are contaminated by Gaussian noise. Furthermore, we apply our algorithm to study the mechanomyographic (MMG) signals arising from contraction of human skeletal muscle. Results obtained from the hybrid symplectic principal component analysis and central tendency measure demonstrate that the skeletal muscle motor unit dynamics can indeed be deterministic, in agreement with previous studies. However, the conventional CTM method was not able to definitely detect the underlying deterministic dynamics. This result on MMG signal analysis is helpful in understanding neuromuscular control mechanisms and developing MMG-based engineering control applications.

  5. A hybrid symplectic principal component analysis and central tendency measure method for detection of determinism in noisy time series with application to mechanomyography.

    PubMed

    Xie, Hong-Bo; Dokos, Socrates

    2013-06-01

    We present a hybrid symplectic geometry and central tendency measure (CTM) method for detection of determinism in noisy time series. CTM is effective for detecting determinism in short time series and has been applied in many areas of nonlinear analysis. However, its performance significantly degrades in the presence of strong noise. In order to circumvent this difficulty, we propose to use symplectic principal component analysis (SPCA), a new chaotic signal de-noising method, as the first step to recover the system dynamics. CTM is then applied to determine whether the time series arises from a stochastic process or has a deterministic component. Results from numerical experiments, ranging from six benchmark deterministic models to 1/f noise, suggest that the hybrid method can significantly improve detection of determinism in noisy time series by about 20 dB when the data are contaminated by Gaussian noise. Furthermore, we apply our algorithm to study the mechanomyographic (MMG) signals arising from contraction of human skeletal muscle. Results obtained from the hybrid symplectic principal component analysis and central tendency measure demonstrate that the skeletal muscle motor unit dynamics can indeed be deterministic, in agreement with previous studies. However, the conventional CTM method was not able to definitely detect the underlying deterministic dynamics. This result on MMG signal analysis is helpful in understanding neuromuscular control mechanisms and developing MMG-based engineering control applications.

  6. Development of Database for Accident Analysis in Indian Mines

    NASA Astrophysics Data System (ADS)

    Tripathy, Debi Prasad; Guru Raghavendra Reddy, K.

    2016-10-01

    Mining is a hazardous industry and high accident rates associated with underground mining is a cause of deep concern. Technological developments notwithstanding, rate of fatal accidents and reportable incidents have not shown corresponding levels of decline. This paper argues that adoption of appropriate safety standards by both mine management and the government may result in appreciable reduction in accident frequency. This can be achieved by using the technology in improving the working conditions, sensitising workers and managers about causes and prevention of accidents. Inputs required for a detailed analysis of an accident include information on location, time, type, cost of accident, victim, nature of injury, personal and environmental factors etc. Such information can be generated from data available in the standard coded accident report form. This paper presents a web based application for accident analysis in Indian mines during 2001-2013. An accident database (SafeStat) prototype based on Intranet of the TCP/IP agreement, as developed by the authors, is also discussed.

  7. Type A Accident Investigation Board report on the January 17, 1996, electrical accident with injury in Technical Area 21 Tritium Science and Fabrication Facility Los Alamos National Laboratory. Final report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    NONE

    1996-04-01

    An electrical accident was investigated in which a crafts person received serious injuries as a result of coming into contact with a 13.2 kilovolt (kV) electrical cable in the basement of Building 209 in Technical Area 21 (TA-21-209) in the Tritium Science and Fabrication Facility (TSFF) at Los Alamos National Laboratory (LANL). In conducting its investigation, the Accident Investigation Board used various analytical techniques, including events and causal factor analysis, barrier analysis, change analysis, fault tree analysis, materials analysis, and root cause analysis. The board inspected the accident site, reviewed events surrounding the accident, conducted extensive interviews and document reviews,more » and performed causation analyses to determine the factors that contributed to the accident, including any management system deficiencies. Relevant management systems and factors that could have contributed to the accident were evaluated in accordance with the guiding principles of safety management identified by the Secretary of Energy in an October 1994 letter to the Defense Nuclear Facilities Safety Board and subsequently to Congress.« less

  8. Truck accidents at freeway ramps : data analysis and high-risk site identification

    DOT National Transportation Integrated Search

    1998-01-01

    To examine the relationship of ramp design to truck accident rates, this paper presents an analysis of truck accidents in Washington State, plus a comparison to limited data from Colorado and California. The authors group freeway truck accidents by r...

  9. Systems thinking, the Swiss Cheese Model and accident analysis: a comparative systemic analysis of the Grayrigg train derailment using the ATSB, AcciMap and STAMP models.

    PubMed

    Underwood, Peter; Waterson, Patrick

    2014-07-01

    The Swiss Cheese Model (SCM) is the most popular accident causation model and is widely used throughout various industries. A debate exists in the research literature over whether the SCM remains a viable tool for accident analysis. Critics of the model suggest that it provides a sequential, oversimplified view of accidents. Conversely, proponents suggest that it embodies the concepts of systems theory, as per the contemporary systemic analysis techniques. The aim of this paper was to consider whether the SCM can provide a systems thinking approach and remain a viable option for accident analysis. To achieve this, the train derailment at Grayrigg was analysed with an SCM-based model (the ATSB accident investigation model) and two systemic accident analysis methods (AcciMap and STAMP). The analysis outputs and usage of the techniques were compared. The findings of the study showed that each model applied the systems thinking approach. However, the ATSB model and AcciMap graphically presented their findings in a more succinct manner, whereas STAMP more clearly embodied the concepts of systems theory. The study suggests that, whilst the selection of an analysis method is subject to trade-offs that practitioners and researchers must make, the SCM remains a viable model for accident analysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Aspen succession in the Intermountain West: A deterministic model

    Treesearch

    Dale L. Bartos; Frederick R. Ward; George S. Innis

    1983-01-01

    A deterministic model of succession in aspen forests was developed using existing data and intuition. The degree of uncertainty, which was determined by allowing the parameter values to vary at random within limits, was larger than desired. This report presents results of an analysis of model sensitivity to changes in parameter values. These results have indicated...

  11. Probabilistic Design and Analysis Framework

    NASA Technical Reports Server (NTRS)

    Strack, William C.; Nagpal, Vinod K.

    2010-01-01

    PRODAF is a software package designed to aid analysts and designers in conducting probabilistic analysis of components and systems. PRODAF can integrate multiple analysis programs to ease the tedious process of conducting a complex analysis process that requires the use of multiple software packages. The work uses a commercial finite element analysis (FEA) program with modules from NESSUS to conduct a probabilistic analysis of a hypothetical turbine blade, disk, and shaft model. PRODAF applies the response surface method, at the component level, and extrapolates the component-level responses to the system level. Hypothetical components of a gas turbine engine are first deterministically modeled using FEA. Variations in selected geometrical dimensions and loading conditions are analyzed to determine the effects of the stress state within each component. Geometric variations include the cord length and height for the blade, inner radius, outer radius, and thickness, which are varied for the disk. Probabilistic analysis is carried out using developing software packages like System Uncertainty Analysis (SUA) and PRODAF. PRODAF was used with a commercial deterministic FEA program in conjunction with modules from the probabilistic analysis program, NESTEM, to perturb loads and geometries to provide a reliability and sensitivity analysis. PRODAF simplified the handling of data among the various programs involved, and will work with many commercial and opensource deterministic programs, probabilistic programs, or modules.

  12. An Evidential Reasoning-Based CREAM to Human Reliability Analysis in Maritime Accident Process.

    PubMed

    Wu, Bing; Yan, Xinping; Wang, Yang; Soares, C Guedes

    2017-10-01

    This article proposes a modified cognitive reliability and error analysis method (CREAM) for estimating the human error probability in the maritime accident process on the basis of an evidential reasoning approach. This modified CREAM is developed to precisely quantify the linguistic variables of the common performance conditions and to overcome the problem of ignoring the uncertainty caused by incomplete information in the existing CREAM models. Moreover, this article views maritime accident development from the sequential perspective, where a scenario- and barrier-based framework is proposed to describe the maritime accident process. This evidential reasoning-based CREAM approach together with the proposed accident development framework are applied to human reliability analysis of a ship capsizing accident. It will facilitate subjective human reliability analysis in different engineering systems where uncertainty exists in practice. © 2017 Society for Risk Analysis.

  13. Spatial delineation, fluid-lithology characterization, and petrophysical modeling of deepwater Gulf of Mexico reservoirs though joint AVA deterministic and stochastic inversion of three-dimensional partially-stacked seismic amplitude data and well logs

    NASA Astrophysics Data System (ADS)

    Contreras, Arturo Javier

    This dissertation describes a novel Amplitude-versus-Angle (AVA) inversion methodology to quantitatively integrate pre-stack seismic data, well logs, geologic data, and geostatistical information. Deterministic and stochastic inversion algorithms are used to characterize flow units of deepwater reservoirs located in the central Gulf of Mexico. A detailed fluid/lithology sensitivity analysis was conducted to assess the nature of AVA effects in the study area. Standard AVA analysis indicates that the shale/sand interface represented by the top of the hydrocarbon-bearing turbidite deposits generate typical Class III AVA responses. Layer-dependent Biot-Gassmann analysis shows significant sensitivity of the P-wave velocity and density to fluid substitution, indicating that presence of light saturating fluids clearly affects the elastic response of sands. Accordingly, AVA deterministic and stochastic inversions, which combine the advantages of AVA analysis with those of inversion, have provided quantitative information about the lateral continuity of the turbidite reservoirs based on the interpretation of inverted acoustic properties and fluid-sensitive modulus attributes (P-Impedance, S-Impedance, density, and LambdaRho, in the case of deterministic inversion; and P-velocity, S-velocity, density, and lithotype (sand-shale) distributions, in the case of stochastic inversion). The quantitative use of rock/fluid information through AVA seismic data, coupled with the implementation of co-simulation via lithotype-dependent multidimensional joint probability distributions of acoustic/petrophysical properties, provides accurate 3D models of petrophysical properties such as porosity, permeability, and water saturation. Pre-stack stochastic inversion provides more realistic and higher-resolution results than those obtained from analogous deterministic techniques. Furthermore, 3D petrophysical models can be more accurately co-simulated from AVA stochastic inversion results. By combining AVA sensitivity analysis techniques with pre-stack stochastic inversion, geologic data, and awareness of inversion pitfalls, it is possible to substantially reduce the risk in exploration and development of conventional and non-conventional reservoirs. From the final integration of deterministic and stochastic inversion results with depositional models and analogous examples, the M-series reservoirs have been interpreted as stacked terminal turbidite lobes within an overall fan complex (the Miocene MCAVLU Submarine Fan System); this interpretation is consistent with previous core data interpretations and regional stratigraphic/depositional studies.

  14. Canister Storage Building (CSB) Design Basis Accident Analysis Documentation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    CROWE, R.D.; PIEPHO, M.G.

    2000-03-23

    This document provided the detailed accident analysis to support HNF-3553, Spent Nuclear Fuel Project Final Safety Analysis Report, Annex A, ''Canister Storage Building Final Safety Analysis Report''. All assumptions, parameters, and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the Canister Storage Building Final Safety Analysis Report.

  15. Analysis of wireless sensor network topology and estimation of optimal network deployment by deterministic radio channel characterization.

    PubMed

    Aguirre, Erik; Lopez-Iturri, Peio; Azpilicueta, Leire; Astrain, José Javier; Villadangos, Jesús; Falcone, Francisco

    2015-02-05

    One of the main challenges in the implementation and design of context-aware scenarios is the adequate deployment strategy for Wireless Sensor Networks (WSNs), mainly due to the strong dependence of the radiofrequency physical layer with the surrounding media, which can lead to non-optimal network designs. In this work, radioplanning analysis for WSN deployment is proposed by employing a deterministic 3D ray launching technique in order to provide insight into complex wireless channel behavior in context-aware indoor scenarios. The proposed radioplanning procedure is validated with a testbed implemented with a Mobile Ad Hoc Network WSN following a chain configuration, enabling the analysis and assessment of a rich variety of parameters, such as received signal level, signal quality and estimation of power consumption. The adoption of deterministic radio channel techniques allows the design and further deployment of WSNs in heterogeneous wireless scenarios with optimized behavior in terms of coverage, capacity, quality of service and energy consumption.

  16. Indonesian Sea Accident Analysis (Case Study From 2003 – 2013)

    NASA Astrophysics Data System (ADS)

    Arya Dewanto, Y.; Faturachman, D.

    2018-03-01

    There are so many accidents in sea transportation in Indonesia. Most of the accidents happen because of low concern aspects of the safety and security of the crew. In sailing, a man as transport users to interact with the ship and the surrounding environment (including other ships, cruise lines, ports, and the situation of local conditions). These interactions are sometimes very complex and related to various aspects of. Aware of the multiplicity of aspects related to the third of these factors, seeking the safety of cruise through a reduction in the number of accidents and the risk of death and serious injuries due to accidents and goods transported is certainly not enough attempted through mono-sector approach, but rather takes a multi-sector approach to the efforts. In this paper, we described the Indonesian Sea Transportation accident analysis for eleven years divided into four items: total of ship accident type, ship accident factor, total of casualties, region of ship accidents. All data founded from Marine Court (Mahkamah Pelayaran). From that 4 items we can find Indonesia Sea Accident Analysis from 2003-2013.

  17. A cluster analysis on road traffic accidents using genetic algorithms

    NASA Astrophysics Data System (ADS)

    Saharan, Sabariah; Baragona, Roberto

    2017-04-01

    The analysis of traffic road accidents is increasingly important because of the accidents cost and public road safety. The availability or large data sets makes the study of factors that affect the frequency and severity accidents are viable. However, the data are often highly unbalanced and overlapped. We deal with the data set of the road traffic accidents recorded in Christchurch, New Zealand, from 2000-2009 with a total of 26440 accidents. The data is in a binary set and there are 50 factors road traffic accidents with four level of severity. We used genetic algorithm for the analysis because we are in the presence of a large unbalanced data set and standard clustering like k-means algorithm may not be suitable for the task. The genetic algorithm based on clustering for unknown K, (GCUK) has been used to identify the factors associated with accidents of different levels of severity. The results provided us with an interesting insight into the relationship between factors and accidents severity level and suggest that the two main factors that contributes to fatal accidents are "Speed greater than 60 km h" and "Did not see other people until it was too late". A comparison with the k-means algorithm and the independent component analysis is performed to validate the results.

  18. Road Traffic Accident Analysis of Ajmer City Using Remote Sensing and GIS Technology

    NASA Astrophysics Data System (ADS)

    Bhalla, P.; Tripathi, S.; Palria, S.

    2014-12-01

    With advancement in technology, new and sophisticated models of vehicle are available and their numbers are increasing day by day. A traffic accident has multi-facet characteristics associated with it. In India 93% of crashes occur due to Human induced factor (wholly or partly). For proper traffic accident analysis use of GIS technology has become an inevitable tool. The traditional accident database is a summary spreadsheet format using codes and mileposts to denote location, type and severity of accidents. Geo-referenced accident database is location-referenced. It incorporates a GIS graphical interface with the accident information to allow for query searches on various accident attributes. Ajmer city, headquarter of Ajmer district, Rajasthan has been selected as the study area. According to Police records, 1531 accidents occur during 2009-2013. Maximum accident occurs in 2009 and the maximum death in 2013. Cars, jeeps, auto, pickup and tempo are mostly responsible for accidents and that the occurrence of accidents is mostly concentrated between 4PM to 10PM. GIS has proved to be a good tool for analyzing multifaceted nature of accidents. While road safety is a critical issue, yet it is handled in an adhoc manner. This Study is a demonstration of application of GIS for developing an efficient database on road accidents taking Ajmer City as a study. If such type of database is developed for other cities, a proper analysis of accidents can be undertaken and suitable management strategies for traffic regulation can be successfully proposed.

  19. Challenging the immediate causes: A work accident investigation in an oil refinery using organizational analysis.

    PubMed

    Beltran, Sandra Lorena; Vilela, Rodolfo Andrade de Gouveia; de Almeida, Ildeberto Muniz

    2018-01-01

    In many companies, investigations of accidents still blame the victims without exploring deeper causes. Those investigations are reactive and have no learning potential. This paper aims to debate the historical organizational aspects of a company whose policy was incubating an accident. The empirical data are analyzed as part of a qualitative study of an accident that occurred in an oil refinery in Brazil in 2014. To investigate and analyse this case we used one-to-one and group interviews, participant observation, Collective Analyses of Work and a documentary review. The analysis was conducted on the basis of concepts of the Organizational Analysis of the event and the Model for Analysis and Prevention of Work Accidents. The accident had its origin in the interaction of social and organizational factors, among them being: excessively standardized culture, management tools and outcome indicators that give a false sense of safety, the decision to speed up the project, the change of operator to facilitate this outcome and performance management that encourages getting around the usual barriers. The superficial accident analysis conducted by the company that ignored human and organizational factors reinforces the traditional safety culture and favors the occurrence of new accidents.

  20. Inherent Conservatism in Deterministic Quasi-Static Structural Analysis

    NASA Technical Reports Server (NTRS)

    Verderaime, V.

    1997-01-01

    The cause of the long-suspected excessive conservatism in the prevailing structural deterministic safety factor has been identified as an inherent violation of the error propagation laws when reducing statistical data to deterministic values and then combining them algebraically through successive structural computational processes. These errors are restricted to the applied stress computations, and because mean and variations of the tolerance limit format are added, the errors are positive, serially cumulative, and excessively conservative. Reliability methods circumvent these errors and provide more efficient and uniform safe structures. The document is a tutorial on the deficiencies and nature of the current safety factor and of its improvement and transition to absolute reliability.

  1. Wet weather highway accident analysis and skid resistance data management system (volume I).

    DOT National Transportation Integrated Search

    1992-06-01

    The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

  2. A stochastic model for correlated protein motions

    NASA Astrophysics Data System (ADS)

    Karain, Wael I.; Qaraeen, Nael I.; Ajarmah, Basem

    2006-06-01

    A one-dimensional Langevin-type stochastic difference equation is used to find the deterministic and Gaussian contributions of time series representing the projections of a Bovine Pancreatic Trypsin Inhibitor (BPTI) protein molecular dynamics simulation along different eigenvector directions determined using principal component analysis. The deterministic part shows a distinct nonlinear behavior only for eigenvectors contributing significantly to the collective protein motion.

  3. Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong.

    PubMed

    Wong, Francis K W; Chan, Albert P C; Wong, Andy K D; Hon, Carol K H; Choi, Tracy N Y

    2018-03-10

    A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the "Public Works Programme Construction Site Safety and Environmental Statistics" (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to 'fall of person from height'; (2) electricians with zero to five years of experience were prone to 'slip, trip or fall on same level'; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched.

  4. Accidents of Electrical and Mechanical Works for Public Sector Projects in Hong Kong

    PubMed Central

    Wong, Francis K. W.; Chan, Albert P. C.; Wong, Andy K. D.; Choi, Tracy N. Y.

    2018-01-01

    A study on electrical and mechanical (E&M) works-related accidents for public sector projects provided the opportunity to gain a better understanding of the causes of accidents by analyzing the circumstances of all E&M works accidents. The research aims to examine accidents of E&M works which happened in public sector projects. A total of 421 E&M works-related accidents in the “Public Works Programme Construction Site Safety and Environmental Statistics” (PCSES) system were extracted for analysis. Two-step cluster analysis was conducted to classify the E&M accidents into different groups. The results identified three E&M accidents groups: (1) electricians with over 15 years of experience were prone to ‘fall of person from height’; (2) electricians with zero to five years of experience were prone to ‘slip, trip or fall on same level’; (3) air-conditioning workers with zero to five years of experience were prone to multiple types of accidents. Practical measures were recommended for each specific cluster group to avoid recurrence of similar accidents. The accident analysis would be vital for industry practitioners to enhance the safety performance of public sector projects. This study contributes to filling the knowledge gap of how and why E&M accidents occur and promulgating preventive measures for E&M accidents which have been under researched. PMID:29534429

  5. Wet weather highway accident analysis and skid resistance data management system (volume II : user's manual).

    DOT National Transportation Integrated Search

    1992-06-01

    The objectives and scope of this research are to establish an effective methodology for wet weather accident analysis and to develop a database management system to facilitate information processing and storage for the accident analysis process, skid...

  6. United States Department of Energy severe accident research following the Fukushima Daiichi accidents

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farmer, M. T.; Corradini, M.; Rempe, J.

    The U.S. Department of Energy (DOE) has played a major role in the U.S. response to the events at Fukushima Daiichi. During the first several weeks following the accident, U.S. assistance efforts were guided by results from a significant and diverse set of analyses. In the months that followed, a coordinated analysis activity aimed at gaining a more thorough understanding of the accident sequence was completed using laboratory-developed, system-level best-estimate accident analysis codes, while a parallel analysis was conducted by U.S. industry. A comparison of predictions for Unit 1 from these two studies indicated significant differences between MAAP and MELCORmore » results for key plant parameters, such as in-core hydrogen production. On that basis, a crosswalk was completed to determine the key modeling variations that led to these differences. In parallel with these activities, it became clear that there was a need to perform a technology gap evaluation on accident-tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist given the current state of light water reactor (LWR) severe accident research and augmented by insights from Fukushima. In addition, there is growing international recognition that data from Fukushima could significantly reduce uncertainties related to severe accident progression, particularly for boiling water reactors. On these bases, a group of U. S. experts in LWR safety and plant operations was convened by the DOE Office of Nuclear Energy (DOE-NE) to complete technology gap analysis and Fukushima forensics data needs identification activities. The results from these activities were used as the basis for refining DOE-NE's severe accident research and development (R&D) plan. Finally, this paper provides a high-level review of DOE-sponsored R&D efforts in these areas, including planned activities on accident-tolerant components and accident analysis methods.« less

  7. United States Department of Energy severe accident research following the Fukushima Daiichi accidents

    DOE PAGES

    Farmer, M. T.; Corradini, M.; Rempe, J.; ...

    2016-11-02

    The U.S. Department of Energy (DOE) has played a major role in the U.S. response to the events at Fukushima Daiichi. During the first several weeks following the accident, U.S. assistance efforts were guided by results from a significant and diverse set of analyses. In the months that followed, a coordinated analysis activity aimed at gaining a more thorough understanding of the accident sequence was completed using laboratory-developed, system-level best-estimate accident analysis codes, while a parallel analysis was conducted by U.S. industry. A comparison of predictions for Unit 1 from these two studies indicated significant differences between MAAP and MELCORmore » results for key plant parameters, such as in-core hydrogen production. On that basis, a crosswalk was completed to determine the key modeling variations that led to these differences. In parallel with these activities, it became clear that there was a need to perform a technology gap evaluation on accident-tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist given the current state of light water reactor (LWR) severe accident research and augmented by insights from Fukushima. In addition, there is growing international recognition that data from Fukushima could significantly reduce uncertainties related to severe accident progression, particularly for boiling water reactors. On these bases, a group of U. S. experts in LWR safety and plant operations was convened by the DOE Office of Nuclear Energy (DOE-NE) to complete technology gap analysis and Fukushima forensics data needs identification activities. The results from these activities were used as the basis for refining DOE-NE's severe accident research and development (R&D) plan. Finally, this paper provides a high-level review of DOE-sponsored R&D efforts in these areas, including planned activities on accident-tolerant components and accident analysis methods.« less

  8. Cross-frequency and band-averaged response variance prediction in the hybrid deterministic-statistical energy analysis method

    NASA Astrophysics Data System (ADS)

    Reynders, Edwin P. B.; Langley, Robin S.

    2018-08-01

    The hybrid deterministic-statistical energy analysis method has proven to be a versatile framework for modeling built-up vibro-acoustic systems. The stiff system components are modeled deterministically, e.g., using the finite element method, while the wave fields in the flexible components are modeled as diffuse. In the present paper, the hybrid method is extended such that not only the ensemble mean and variance of the harmonic system response can be computed, but also of the band-averaged system response. This variance represents the uncertainty that is due to the assumption of a diffuse field in the flexible components of the hybrid system. The developments start with a cross-frequency generalization of the reciprocity relationship between the total energy in a diffuse field and the cross spectrum of the blocked reverberant loading at the boundaries of that field. By making extensive use of this generalization in a first-order perturbation analysis, explicit expressions are derived for the cross-frequency and band-averaged variance of the vibrational energies in the diffuse components and for the cross-frequency and band-averaged variance of the cross spectrum of the vibro-acoustic field response of the deterministic components. These expressions are extensively validated against detailed Monte Carlo analyses of coupled plate systems in which diffuse fields are simulated by randomly distributing small point masses across the flexible components, and good agreement is found.

  9. Who by accident? The social morphology of car accidents.

    PubMed

    Factor, Roni; Yair, Gad; Mahalel, David

    2010-09-01

    Prior studies in the sociology of accidents have shown that different social groups have different rates of accident involvement. This study extends those studies by implementing Bourdieu's relational perspective of social space to systematically explore the homology between drivers' social characteristics and their involvement in specific types of motor vehicle accident. Using a large database that merges official Israeli road-accident records with socioeconomic data from two censuses, this research maps the social order of road accidents through multiple correspondence analysis. Extending prior studies, the results show that different social groups indeed tend to be involved in motor vehicle accidents of different types and severity. For example, we find that drivers from low socioeconomic backgrounds are overinvolved in severe accidents with fatal outcomes. The new findings reported here shed light on the social regularity of road accidents and expose new facets in the social organization of death. © 2010 Society for Risk Analysis.

  10. Domino effect in chemical accidents: main features and accident sequences.

    PubMed

    Darbra, R M; Palacios, Adriana; Casal, Joaquim

    2010-11-15

    The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes are external events (31%) and mechanical failure (29%). Storage areas (35%) and process plants (28%) are by far the most common settings for domino accidents. Eighty-nine per cent of the accidents involved flammable materials, the most frequent of which was LPG. The domino effect sequences were analyzed using relative probability event trees. The most frequent sequences were explosion→fire (27.6%), fire→explosion (27.5%) and fire→fire (17.8%). Copyright © 2010 Elsevier B.V. All rights reserved.

  11. Design and application of a tool for structuring, capitalizing and making more accessible information and lessons learned from accidents involving machinery.

    PubMed

    Sadeghi, Samira; Sadeghi, Leyla; Tricot, Nicolas; Mathieu, Luc

    2017-12-01

    Accident reports are published in order to communicate the information and lessons learned from accidents. An efficient accident recording and analysis system is a necessary step towards improvement of safety. However, currently there is a shortage of efficient tools to support such recording and analysis. In this study we introduce a flexible and customizable tool that allows structuring and analysis of this information. This tool has been implemented under TEEXMA®. We named our prototype TEEXMA®SAFETY. This tool provides an information management system to facilitate data collection, organization, query, analysis and reporting of accidents. A predefined information retrieval module provides ready access to data which allows the user to quickly identify the possible hazards for specific machines and provides information on the source of hazards. The main target audience for this tool includes safety personnel, accident reporters and designers. The proposed data model has been developed by analyzing different accident reports.

  12. A human factors analysis of fatal and serious injury accidents in Alaska, 2004-2009.

    DOT National Transportation Integrated Search

    2011-12-01

    "This report summarizes the analysis of 97 general aviation accidents in Alaska that resulted in a fatality or serious : injury to one or more aircraft occupants for the years 2004-2009. The accidents were analyzed using the Human : Factors Analysis ...

  13. ({The) Solar System Large Planets influence on a new Maunder Miniμm}

    NASA Astrophysics Data System (ADS)

    Yndestad, Harald; Solheim, Jan-Erik

    2016-04-01

    In 1890´s G. Spörer and E. W. Maunder (1890) reported that the solar activity stopped in a period of 70 years from 1645 to 1715. Later a reconstruction of the solar activity confirms the grand minima Maunder (1640-1720), Spörer (1390-1550), Wolf (1270-1340), and the minima Oort (1010-1070) and Dalton (1785-1810) since the year 1000 A.D. (Usoskin et al. 2007). These minimum periods have been associated with less irradiation from the Sun and cold climate periods on Earth. An identification of a three grand Maunder type periods and two Dalton type periods in a period thousand years, indicates that sooner or later there will be a colder climate on Earth from a new Maunder- or Dalton- type period. The cause of these minimum periods, are not well understood. An expected new Maunder-type period is based on the properties of solar variability. If the solar variability has a deterministic element, we can estimate better a new Maunder grand minimum. A random solar variability can only explain the past. This investigation is based on the simple idea that if the solar variability has a deterministic property, it must have a deterministic source, as a first cause. If this deterministic source is known, we can compute better estimates the next expected Maunder grand minimum period. The study is based on a TSI ACRIM data series from 1700, a TSI ACRIM data series from 1000 A.D., sunspot data series from 1611 and a Solar Barycenter orbit data series from 1000. The analysis method is based on a wavelet spectrum analysis, to identify stationary periods, coincidence periods and their phase relations. The result shows that the TSI variability and the sunspots variability have deterministic oscillations, controlled by the large planets Jupiter, Uranus and Neptune, as the first cause. A deterministic model of TSI variability and sunspot variability confirms the known minimum and grand minimum periods since 1000. From this deterministic model we may expect a new Maunder type sunspot minimum period from about 2018 to 2055. The deterministic model of a TSI ACRIM data series from 1700 computes a new Maunder type grand minimum period from 2015 to 2071. A model of the longer TSI ACRIM data series from 1000 computes a new Dalton to Maunder type minimum irradiation period from 2047 to 2068.

  14. Archetypes for Organisational Safety

    NASA Technical Reports Server (NTRS)

    Marais, Karen; Leveson, Nancy G.

    2003-01-01

    We propose a framework using system dynamics to model the dynamic behavior of organizations in accident analysis. Most current accident analysis techniques are event-based and do not adequately capture the dynamic complexity and non-linear interactions that characterize accidents in complex systems. In this paper we propose a set of system safety archetypes that model common safety culture flaws in organizations, i.e., the dynamic behaviour of organizations that often leads to accidents. As accident analysis and investigation tools, the archetypes can be used to develop dynamic models that describe the systemic and organizational factors contributing to the accident. The archetypes help clarify why safety-related decisions do not always result in the desired behavior, and how independent decisions in different parts of the organization can combine to impact safety.

  15. An analysis of aircraft accidents involving fires

    NASA Technical Reports Server (NTRS)

    Lucha, G. V.; Robertson, M. A.; Schooley, F. A.

    1975-01-01

    All U. S. Air Carrier accidents between 1963 and 1974 were studied to assess the extent of total personnel and aircraft damage which occurred in accidents and in accidents involving fire. Published accident reports and NTSB investigators' factual backup files were the primary sources of data. Although it was frequently not possible to assess the relative extent of fire-caused damage versus impact damage using the available data, the study established upper and lower bounds for deaths and damage due specifically to fire. In 12 years there were 122 accidents which involved airframe fires. Eighty-seven percent of the fires occurred after impact, and fuel leakage from ruptured tanks or severed lines was the most frequently cited cause. A cost analysis was performed for 300 serious accidents, including 92 serious accidents which involved fire. Personal injury costs were outside the scope of the cost analysis, but data on personnel injury judgements as well as settlements received from the CAB are included for reference.

  16. Construction industry accidents in Spain.

    PubMed

    Camino López, Miguel A; Ritzel, Dale O; Fontaneda, Ignacio; González Alcantara, Oscar J

    2008-01-01

    This paper analyzed industrial accidents that take place on construction sites and their severity. Eighteen variables were studied. We analyzed the influence of each of these with respect to the severity and fatality of the accident. This descriptive analysis was grounded in 1,630,452 accidents, representing the total number of accidents suffered by workers in the construction sector in Spain over the period 1990-2000. It was shown that age, type of contract, time of accident, length of service in the company, company size, day of the week, and the remainder of the variables under analysis influenced the seriousness of the accident. IMPACT ON INJURY PREVENTION: The results obtained show that different training was needed, depending on the severity of accidents, for different age, length of service in the company, organization of work, and time when workers work. The research provides an insight to the likely causes of construction injuries in Spain. As a result of the analysis, industries and governmental agencies in Spain can start to provide appropriate strategies and training to the construction workers.

  17. A study on industrial accident rate forecasting and program development of estimated zero accident time in Korea.

    PubMed

    Kim, Tae-gu; Kang, Young-sig; Lee, Hyung-won

    2011-01-01

    To begin a zero accident campaign for industry, the first thing is to estimate the industrial accident rate and the zero accident time systematically. This paper considers the social and technical change of the business environment after beginning the zero accident campaign through quantitative time series analysis methods. These methods include sum of squared errors (SSE), regression analysis method (RAM), exponential smoothing method (ESM), double exponential smoothing method (DESM), auto-regressive integrated moving average (ARIMA) model, and the proposed analytic function method (AFM). The program is developed to estimate the accident rate, zero accident time and achievement probability of an efficient industrial environment. In this paper, MFC (Microsoft Foundation Class) software of Visual Studio 2008 was used to develop a zero accident program. The results of this paper will provide major information for industrial accident prevention and be an important part of stimulating the zero accident campaign within all industrial environments.

  18. Probabilistic analysis of the torsional effects on the tall building resistance due to earthquake even

    NASA Astrophysics Data System (ADS)

    Králik, Juraj; Králik, Juraj

    2017-07-01

    The paper presents the results from the deterministic and probabilistic analysis of the accidental torsional effect of reinforced concrete tall buildings due to earthquake even. The core-column structural system was considered with various configurations in plane. The methodology of the seismic analysis of the building structures in Eurocode 8 and JCSS 2000 is discussed. The possibilities of the utilization the LHS method to analyze the extensive and robust tasks in FEM is presented. The influence of the various input parameters (material, geometry, soil, masses and others) is considered. The deterministic and probability analysis of the seismic resistance of the structure was calculated in the ANSYS program.

  19. An analysis of pilot error-related aircraft accidents

    NASA Technical Reports Server (NTRS)

    Kowalsky, N. B.; Masters, R. L.; Stone, R. B.; Babcock, G. L.; Rypka, E. W.

    1974-01-01

    A multidisciplinary team approach to pilot error-related U.S. air carrier jet aircraft accident investigation records successfully reclaimed hidden human error information not shown in statistical studies. New analytic techniques were developed and applied to the data to discover and identify multiple elements of commonality and shared characteristics within this group of accidents. Three techniques of analysis were used: Critical element analysis, which demonstrated the importance of a subjective qualitative approach to raw accident data and surfaced information heretofore unavailable. Cluster analysis, which was an exploratory research tool that will lead to increased understanding and improved organization of facts, the discovery of new meaning in large data sets, and the generation of explanatory hypotheses. Pattern recognition, by which accidents can be categorized by pattern conformity after critical element identification by cluster analysis.

  20. Automatic mesh adaptivity for hybrid Monte Carlo/deterministic neutronics modeling of difficult shielding problems

    DOE PAGES

    Ibrahim, Ahmad M.; Wilson, Paul P.H.; Sawan, Mohamed E.; ...

    2015-06-30

    The CADIS and FW-CADIS hybrid Monte Carlo/deterministic techniques dramatically increase the efficiency of neutronics modeling, but their use in the accurate design analysis of very large and geometrically complex nuclear systems has been limited by the large number of processors and memory requirements for their preliminary deterministic calculations and final Monte Carlo calculation. Three mesh adaptivity algorithms were developed to reduce the memory requirements of CADIS and FW-CADIS without sacrificing their efficiency improvement. First, a macromaterial approach enhances the fidelity of the deterministic models without changing the mesh. Second, a deterministic mesh refinement algorithm generates meshes that capture as muchmore » geometric detail as possible without exceeding a specified maximum number of mesh elements. Finally, a weight window coarsening algorithm decouples the weight window mesh and energy bins from the mesh and energy group structure of the deterministic calculations in order to remove the memory constraint of the weight window map from the deterministic mesh resolution. The three algorithms were used to enhance an FW-CADIS calculation of the prompt dose rate throughout the ITER experimental facility. Using these algorithms resulted in a 23.3% increase in the number of mesh tally elements in which the dose rates were calculated in a 10-day Monte Carlo calculation and, additionally, increased the efficiency of the Monte Carlo simulation by a factor of at least 3.4. The three algorithms enabled this difficult calculation to be accurately solved using an FW-CADIS simulation on a regular computer cluster, eliminating the need for a world-class super computer.« less

  1. The accident analysis of mobile mine machinery in Indian opencast coal mines.

    PubMed

    Kumar, R; Ghosh, A K

    2014-01-01

    This paper presents the analysis of large mining machinery related accidents in Indian opencast coal mines. The trends of coal production, share of mining methods in production, machinery deployment in open cast mines, size and population of machinery, accidents due to machinery, types and causes of accidents have been analysed from the year 1995 to 2008. The scrutiny of accidents during this period reveals that most of the responsible factors are machine reversal, haul road design, human fault, operator's fault, machine fault, visibility and dump design. Considering the types of machines, namely, dumpers, excavators, dozers and loaders together the maximum number of fatal accidents has been caused by operator's faults and human faults jointly during the period from 1995 to 2008. The novel finding of this analysis is that large machines with state-of-the-art safety system did not reduce the fatal accidents in Indian opencast coal mines.

  2. Aircraft accidents : method of analysis

    NASA Technical Reports Server (NTRS)

    1931-01-01

    The revised report includes the chart for the analysis of aircraft accidents, combining consideration of the immediate causes, underlying causes, and results of accidents, as prepared by the special committee, with a number of the definitions clarified. A brief statement of the organization and work of the special committee and of the Committee on Aircraft Accidents; and statistical tables giving a comparison of the types of accidents and causes of accidents in the military services on the one hand and in civil aviation on the other, together with explanations of some of the important differences noted in these tables.

  3. Organizational influence on the occurrence of work accidents involving exposure to biological material.

    PubMed

    Marziale, Maria Helena Palucci; Rocha, Fernanda Ludmilla Rossi; Robazzi, Maria Lúcia do Carmo Cruz; Cenzi, Camila Maria; dos Santos, Heloisa Ehmke Cardoso; Trovó, Marli Elisa Mendes

    2013-01-01

    to analyze work accidents involving exposure to biological materials which took place among personnel working in nursing and to evaluate the influence of the organizational culture on the occurrence of these accidents. a retrospective, analytical study, carried out in two stages in a hospital that was part of the Network for the Prevention of Work Accidents. The first stage involved the analysis of the characteristics of the work accidents involving exposure to biological materials as recorded over a seven-year period by the nursing staff in the hospital studied, and registered in the Network databank. The second stage involved the analysis of 122 nursing staff members' perception of the institutional culture, who were allocated to the control group (workers who had not had an accident) and the case group (workers who had had an accident). 386 accidents had been recorded: percutaneous lesions occurred in 79% of the cases, needles were the materials involved in 69.7% of the accidents, and in 81.9% of the accident there was contact with blood. Regarding the influence of the organizational culture on the occurrence of accidents, the results obtained through the analysis of the two groups did not demonstrate significant differences between the average scores attributed by the workers in each organizational value or practice category. It is concluded that accidents involving exposure to biological material need to be avoided, however, it was not possible to confirm the influence of organizational values or practices on workers' behavior concerning the occurrence of these accidents.

  4. Analysis on Dangerous Source of Large Safety Accident in Storage Tank Area

    NASA Astrophysics Data System (ADS)

    Wang, Tong; Li, Ying; Xie, Tiansheng; Liu, Yu; Zhu, Xueyuan

    2018-01-01

    The difference between a large safety accident and a general accident is that the consequences of a large safety accident are particularly serious. To study the tank area which factors directly or indirectly lead to the occurrence of large-sized safety accidents. According to the three kinds of hazard source theory and the consequence cause analysis of the super safety accident, this paper analyzes the dangerous source of the super safety accident in the tank area from four aspects, such as energy source, large-sized safety accident reason, management missing, environmental impact Based on the analysis of three kinds of hazard sources and environmental analysis to derive the main risk factors and the AHP evaluation model is established, and after rigorous and scientific calculation, the weights of the related factors in four kinds of risk factors and each type of risk factors are obtained. The result of analytic hierarchy process shows that management reasons is the most important one, and then the environmental factors and the direct cause and Energy source. It should be noted that although the direct cause is relatively low overall importance, the direct cause of Failure of emergency measures and Failure of prevention and control facilities in greater weight.

  5. Systems-based accident analysis in the led outdoor activity domain: application and evaluation of a risk management framework.

    PubMed

    Salmon, P; Williamson, A; Lenné, M; Mitsopoulos-Rubens, E; Rudin-Brown, C M

    2010-08-01

    Safety-compromising accidents occur regularly in the led outdoor activity domain. Formal accident analysis is an accepted means of understanding such events and improving safety. Despite this, there remains no universally accepted framework for collecting and analysing accident data in the led outdoor activity domain. This article presents an application of Rasmussen's risk management framework to the analysis of the Lyme Bay sea canoeing incident. This involved the development of an Accimap, the outputs of which were used to evaluate seven predictions made by the framework. The Accimap output was also compared to an analysis using an existing model from the led outdoor activity domain. In conclusion, the Accimap output was found to be more comprehensive and supported all seven of the risk management framework's predictions, suggesting that it shows promise as a theoretically underpinned approach for analysing, and learning from, accidents in the led outdoor activity domain. STATEMENT OF RELEVANCE: Accidents represent a significant problem within the led outdoor activity domain. This article presents an evaluation of a risk management framework that can be used to understand such accidents and to inform the development of accident countermeasures and mitigation strategies for the led outdoor activity domain.

  6. Deterministic chaos in an ytterbium-doped mode-locked fiber laser

    NASA Astrophysics Data System (ADS)

    Mélo, Lucas B. A.; Palacios, Guillermo F. R.; Carelli, Pedro V.; Acioli, Lúcio H.; Rios Leite, José R.; de Miranda, Marcio H. G.

    2018-05-01

    We experimentally study the nonlinear dynamics of a femtosecond ytterbium doped mode-locked fiber laser. With the laser operating in the pulsed regime a route to chaos is presented, starting from stable mode-locking, period two, period four, chaos and period three regimes. Return maps and bifurcation diagrams were extracted from time series for each regime. The analysis of the time series with the laser operating in the quasi mode-locked regime presents deterministic chaos described by an unidimensional Rossler map. A positive Lyapunov exponent $\\lambda = 0.14$ confirms the deterministic chaos of the system. We suggest an explanation about the observed map by relating gain saturation and intra-cavity loss.

  7. Modeling Uncertainties in EEG Microstates: Analysis of Real and Imagined Motor Movements Using Probabilistic Clustering-Driven Training of Probabilistic Neural Networks.

    PubMed

    Dinov, Martin; Leech, Robert

    2017-01-01

    Part of the process of EEG microstate estimation involves clustering EEG channel data at the global field power (GFP) maxima, very commonly using a modified K-means approach. Clustering has also been done deterministically, despite there being uncertainties in multiple stages of the microstate analysis, including the GFP peak definition, the clustering itself and in the post-clustering assignment of microstates back onto the EEG timecourse of interest. We perform a fully probabilistic microstate clustering and labeling, to account for these sources of uncertainty using the closest probabilistic analog to KM called Fuzzy C-means (FCM). We train softmax multi-layer perceptrons (MLPs) using the KM and FCM-inferred cluster assignments as target labels, to then allow for probabilistic labeling of the full EEG data instead of the usual correlation-based deterministic microstate label assignment typically used. We assess the merits of the probabilistic analysis vs. the deterministic approaches in EEG data recorded while participants perform real or imagined motor movements from a publicly available data set of 109 subjects. Though FCM group template maps that are almost topographically identical to KM were found, there is considerable uncertainty in the subsequent assignment of microstate labels. In general, imagined motor movements are less predictable on a time point-by-time point basis, possibly reflecting the more exploratory nature of the brain state during imagined, compared to during real motor movements. We find that some relationships may be more evident using FCM than using KM and propose that future microstate analysis should preferably be performed probabilistically rather than deterministically, especially in situations such as with brain computer interfaces, where both training and applying models of microstates need to account for uncertainty. Probabilistic neural network-driven microstate assignment has a number of advantages that we have discussed, which are likely to be further developed and exploited in future studies. In conclusion, probabilistic clustering and a probabilistic neural network-driven approach to microstate analysis is likely to better model and reveal details and the variability hidden in current deterministic and binarized microstate assignment and analyses.

  8. Modeling Uncertainties in EEG Microstates: Analysis of Real and Imagined Motor Movements Using Probabilistic Clustering-Driven Training of Probabilistic Neural Networks

    PubMed Central

    Dinov, Martin; Leech, Robert

    2017-01-01

    Part of the process of EEG microstate estimation involves clustering EEG channel data at the global field power (GFP) maxima, very commonly using a modified K-means approach. Clustering has also been done deterministically, despite there being uncertainties in multiple stages of the microstate analysis, including the GFP peak definition, the clustering itself and in the post-clustering assignment of microstates back onto the EEG timecourse of interest. We perform a fully probabilistic microstate clustering and labeling, to account for these sources of uncertainty using the closest probabilistic analog to KM called Fuzzy C-means (FCM). We train softmax multi-layer perceptrons (MLPs) using the KM and FCM-inferred cluster assignments as target labels, to then allow for probabilistic labeling of the full EEG data instead of the usual correlation-based deterministic microstate label assignment typically used. We assess the merits of the probabilistic analysis vs. the deterministic approaches in EEG data recorded while participants perform real or imagined motor movements from a publicly available data set of 109 subjects. Though FCM group template maps that are almost topographically identical to KM were found, there is considerable uncertainty in the subsequent assignment of microstate labels. In general, imagined motor movements are less predictable on a time point-by-time point basis, possibly reflecting the more exploratory nature of the brain state during imagined, compared to during real motor movements. We find that some relationships may be more evident using FCM than using KM and propose that future microstate analysis should preferably be performed probabilistically rather than deterministically, especially in situations such as with brain computer interfaces, where both training and applying models of microstates need to account for uncertainty. Probabilistic neural network-driven microstate assignment has a number of advantages that we have discussed, which are likely to be further developed and exploited in future studies. In conclusion, probabilistic clustering and a probabilistic neural network-driven approach to microstate analysis is likely to better model and reveal details and the variability hidden in current deterministic and binarized microstate assignment and analyses. PMID:29163110

  9. Type airman certification as related to accidents.

    DOT National Transportation Integrated Search

    1967-10-01

    An analysis of 1964 aircraft accidents, using type of airman certificate as a measure of pilot proficiency, is presented. Data show that student pilots generally have a better accident record than any other of the certification groups. Analysis confi...

  10. Application of forensic image analysis in accident investigations.

    PubMed

    Verolme, Ellen; Mieremet, Arjan

    2017-09-01

    Forensic investigations are primarily meant to obtain objective answers that can be used for criminal prosecution. Accident analyses are usually performed to learn from incidents and to prevent similar events from occurring in the future. Although the primary goal may be different, the steps in which information is gathered, interpreted and weighed are similar in both types of investigations, implying that forensic techniques can be of use in accident investigations as well. The use in accident investigations usually means that more information can be obtained from the available information than when used in criminal investigations, since the latter require a higher evidence level. In this paper, we demonstrate the applicability of forensic techniques for accident investigations by presenting a number of cases from one specific field of expertise: image analysis. With the rapid spread of digital devices and new media, a wealth of image material and other digital information has become available for accident investigators. We show that much information can be distilled from footage by using forensic image analysis techniques. These applications show that image analysis provides information that is crucial for obtaining the sequence of events and the two- and three-dimensional geometry of an accident. Since accident investigation focuses primarily on learning from accidents and prevention of future accidents, and less on the blame that is crucial for criminal investigations, the field of application of these forensic tools may be broader than would be the case in purely legal sense. This is an important notion for future accident investigations. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. The impact of young drivers' lifestyle on their road traffic accident risk in greater Athens area.

    PubMed

    Chliaoutakis, J E; Darviri, C; Demakakos, P T

    1999-11-01

    Young drivers (18-24) both in Greece and elsewhere appear to have high rates of road traffic accidents. Many factors contribute to the creation of these high road traffic accidents rates. It has been suggested that lifestyle is an important one. The main objective of this study is to find out and clarify the (potential) relationship between young drivers' lifestyle and the road traffic accident risk they face. Moreover, to examine if all the youngsters have the same elevated risk on the road or not. The sample consisted of 241 young Greek drivers of both sexes. The statistical analysis included factor analysis and logistic regression analysis. Through the principal component analysis a ten factor scale was created which included the basic lifestyle traits of young Greek drivers. The logistic regression analysis showed that the young drivers whose dominant lifestyle trait is alcohol consumption or drive without destination have high accident risk, while these whose dominant lifestyle trait is culture, face low accident risk. Furthermore, young drivers who are religious in one way or another seem to have low accident risk. Finally, some preliminary observations on how health promotion should be put into practice are discussed.

  12. Traits and causes of environmental loss-related chemical accidents in China based on co-word analysis.

    PubMed

    Wu, Desheng; Song, Yu; Xie, Kefan; Zhang, Baofeng

    2018-04-25

    Chemical accidents are major causes of environmental losses and have been debated due to the potential threat to human beings and environment. Compared with the single statistical analysis, co-word analysis of chemical accidents illustrates significant traits at various levels and presents data into a visual network. This study utilizes a co-word analysis of the keywords extracted from the Web crawling texts of environmental loss-related chemical accidents and uses the Pearson's correlation coefficient to examine the internal attributes. To visualize the keywords of the accidents, this study carries out a multidimensional scaling analysis applying PROXSCAL and centrality identification. The research results show that an enormous environmental cost is exacted, especially given the expected environmental loss-related chemical accidents with geographical features. Meanwhile, each event often brings more than one environmental impact. Large number of chemical substances are released in the form of solid, liquid, and gas, leading to serious results. Eight clusters that represent the traits of these accidents are formed, including "leakage," "poisoning," "explosion," "pipeline crack," "river pollution," "dust pollution," "emission," and "industrial effluent." "Explosion" and "gas" possess a strong correlation with "poisoning," located at the center of visualization map.

  13. Accident models for two-lane rural roads : segments and intersections

    DOT National Transportation Integrated Search

    1998-10-01

    This report is a direct step for the implementation of the Accident Analysis Module in the Interactive Highway Safety Design Model (IHSDM). The Accident Analysis Module is expected to estimate the safety of two-lane rural highway characteristics for ...

  14. Analysis of traffic accident data in Kentucky (1994-1998)

    DOT National Transportation Integrated Search

    1999-09-01

    This report includes an analysis of traffic accident data in Kentucky for the years of 1994 through 1998. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

  15. Estimating the causes of traffic accidents using logistic regression and discriminant analysis.

    PubMed

    Karacasu, Murat; Ergül, Barış; Altin Yavuz, Arzu

    2014-01-01

    Factors that affect traffic accidents have been analysed in various ways. In this study, we use the methods of logistic regression and discriminant analysis to determine the damages due to injury and non-injury accidents in the Eskisehir Province. Data were obtained from the accident reports of the General Directorate of Security in Eskisehir; 2552 traffic accidents between January and December 2009 were investigated regarding whether they resulted in injury. According to the results, the effects of traffic accidents were reflected in the variables. These results provide a wealth of information that may aid future measures toward the prevention of undesired results.

  16. Robust Sensitivity Analysis for Multi-Attribute Deterministic Hierarchical Value Models

    DTIC Science & Technology

    2002-03-01

    such as weighted sum method, weighted 5 product method, and the Analytic Hierarchy Process ( AHP ). This research focuses on only weighted sum...different groups. They can be termed as deterministic, stochastic, or fuzzy multi-objective decision methods if they are classified according to the...weighted product model (WPM), and analytic hierarchy process ( AHP ). His method attempts to identify the most important criteria weight and the most

  17. [Analysis of work accidents during the years 1999-2006 in a hospital company in Lombardia].

    PubMed

    Melloni, P; Antoniazzi, E; Somenzi, V; Galli, L; Fazioli, R; Mottinelli, A; Franzosi, C; Cirla, A M; Gobba, E

    2007-01-01

    This study describe accidents occurred in the period between 1999 and 2006 in the Hospital of Cremona, in which about 2400 subjects operate. The analysis of Accident Register showed a reduction of about 30% of the total number of accidents during the examined period and a non homogeneous distribution of the various types of accidents. The most frequent accidents were prick (25.8%), trauma (22.9%) and "in itinere" accidents (7.8%). One type of accident has been little considered up to now: the aggressions. Professional nurses were the most frequently involved and the most affected units were those that belong to the Internal Medicine Department. "In itinere" accidents had the longest average prognosis (11.6 days). The repetition of accidents occurred to the same operator hasn't been analysed before now: a professional nurse had nine accidents (of various type) in the seven years considered. Probably the reduction of accident must be attributed to the effectiveness of the prevention activities undertaken during the reviewed period. Biological accidents, for which it was possible to implement prevention programs, have been markedly reduced; it was not the same for "In Itinere" accidents, that depend significantly on external factors that are not easily dismissed.

  18. [Proposal of a method for collective analysis of work-related accidents in the hospital setting].

    PubMed

    Osório, Claudia; Machado, Jorge Mesquita Huet; Minayo-Gomez, Carlos

    2005-01-01

    The article presents a method for the analysis of work-related accidents in hospitals, with the double aim of analyzing accidents in light of actual work activity and enhancing the vitality of the various professions that comprise hospital work. This process involves both research and intervention, combining knowledge output with training of health professionals, fostering expanded participation by workers in managing their daily work. The method consists of stimulating workers to recreate the situation in which a given accident occurred, shifting themselves to the position of observers of their own work. In the first stage of analysis, workers are asked to show the work analyst how the accident occurred; in the second stage, the work accident victim and analyst jointly record the described series of events in a diagram; in the third, the resulting record is re-discussed and further elaborated; in the fourth, the work accident victim and analyst evaluate and implement measures aimed to prevent the accident from recurring. The article concludes by discussing the method's possibilities and limitations in the hospital setting.

  19. Trend analysis of Arctic sea ice extent

    NASA Astrophysics Data System (ADS)

    Silva, M. E.; Barbosa, S. M.; Antunes, Luís; Rocha, Conceição

    2009-04-01

    The extent of Arctic sea ice is a fundamental parameter of Arctic climate variability. In the context of climate change, the area covered by ice in the Arctic is a particularly useful indicator of recent changes in the Arctic environment. Climate models are in near universal agreement that Arctic sea ice extent will decline through the 21st century as a consequence of global warming and many studies predict a ice free Arctic as soon as 2012. Time series of satellite passive microwave observations allow to assess the temporal changes in the extent of Arctic sea ice. Much of the analysis of the ice extent time series, as in most climate studies from observational data, have been focussed on the computation of deterministic linear trends by ordinary least squares. However, many different processes, including deterministic, unit root and long-range dependent processes can engender trend like features in a time series. Several parametric tests have been developed, mainly in econometrics, to discriminate between stationarity (no trend), deterministic trend and stochastic trends. Here, these tests are applied in the trend analysis of the sea ice extent time series available at National Snow and Ice Data Center. The parametric stationary tests, Augmented Dickey-Fuller (ADF), Phillips-Perron (PP) and the KPSS, do not support an overall deterministic trend in the time series of Arctic sea ice extent. Therefore, alternative parametrizations such as long-range dependence should be considered for characterising long-term Arctic sea ice variability.

  20. NASA's Accident Precursor Analysis Process and the International Space Station

    NASA Technical Reports Server (NTRS)

    Groen, Frank; Lutomski, Michael

    2010-01-01

    This viewgraph presentation reviews the implementation of Accident Precursor Analysis (APA), as well as the evaluation of In-Flight Investigations (IFI) and Problem Reporting and Corrective Action (PRACA) data for the identification of unrecognized accident potentials on the International Space Station.

  1. Preliminary analysis of the National Crash Severity Study : factors in fatal accidents

    DOT National Transportation Integrated Search

    1979-06-01

    This study investigates the fatalities on the National Crash Severity Study (NCSS) of towaway, passenger car accidents. The analysis is in three stages. First, NCSS fatalities are compared to the fatally-injured occupants reported on the Fatal Accide...

  2. Analysis of traffic accident data in Kentucky (1986-1990)

    DOT National Transportation Integrated Search

    1991-09-01

    This report includes an analysis of traffic accident data in Kentucky for the years of 1986-1990. A primary objectve of this study was to determine average statistics for kentucky highways. Average and critical number and rates of accidents were calc...

  3. Aircraft Loss-of-Control: Analysis and Requirements for Future Safety-Critical Systems and Their Validation

    NASA Technical Reports Server (NTRS)

    Belcastro, Christine M.

    2011-01-01

    Loss of control remains one of the largest contributors to fatal aircraft accidents worldwide. Aircraft loss-of-control accidents are complex, resulting from numerous causal and contributing factors acting alone or more often in combination. Hence, there is no single intervention strategy to prevent these accidents. This paper summarizes recent analysis results in identifying worst-case combinations of loss-of-control accident precursors and their time sequences, a holistic approach to preventing loss-of-control accidents in the future, and key requirements for validating the associated technologies.

  4. Probabilistic safety assessment of the design of a tall buildings under the extreme load

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Králik, Juraj, E-mail: juraj.kralik@stuba.sk

    2016-06-08

    The paper describes some experiences from the deterministic and probabilistic analysis of the safety of the tall building structure. There are presented the methods and requirements of Eurocode EN 1990, standard ISO 2394 and JCSS. The uncertainties of the model and resistance of the structures are considered using the simulation methods. The MONTE CARLO, LHS and RSM probabilistic methods are compared with the deterministic results. On the example of the probability analysis of the safety of the tall buildings is demonstrated the effectiveness of the probability design of structures using Finite Element Methods.

  5. Rare event computation in deterministic chaotic systems using genealogical particle analysis

    NASA Astrophysics Data System (ADS)

    Wouters, J.; Bouchet, F.

    2016-09-01

    In this paper we address the use of rare event computation techniques to estimate small over-threshold probabilities of observables in deterministic dynamical systems. We demonstrate that genealogical particle analysis algorithms can be successfully applied to a toy model of atmospheric dynamics, the Lorenz ’96 model. We furthermore use the Ornstein-Uhlenbeck system to illustrate a number of implementation issues. We also show how a time-dependent objective function based on the fluctuation path to a high threshold can greatly improve the performance of the estimator compared to a fixed-in-time objective function.

  6. Probabilistic safety assessment of the design of a tall buildings under the extreme load

    NASA Astrophysics Data System (ADS)

    Králik, Juraj

    2016-06-01

    The paper describes some experiences from the deterministic and probabilistic analysis of the safety of the tall building structure. There are presented the methods and requirements of Eurocode EN 1990, standard ISO 2394 and JCSS. The uncertainties of the model and resistance of the structures are considered using the simulation methods. The MONTE CARLO, LHS and RSM probabilistic methods are compared with the deterministic results. On the example of the probability analysis of the safety of the tall buildings is demonstrated the effectiveness of the probability design of structures using Finite Element Methods.

  7. An association between dietary habits and traffic accidents in patients with chronic liver disease: A data-mining analysis

    PubMed Central

    KAWAGUCHI, TAKUMI; SUETSUGU, TAKURO; OGATA, SHYOU; IMANAGA, MINAMI; ISHII, KUMIKO; ESAKI, NAO; SUGIMOTO, MASAKO; OTSUYAMA, JYURI; NAGAMATSU, AYU; TANIGUCHI, EITARO; ITOU, MINORU; ORIISHI, TETSUHARU; IWASAKI, SHOKO; MIURA, HIROKO; TORIMURA, TAKUJI

    2016-01-01

    The incidence of traffic accidents in patients with chronic liver disease (CLD) is high in the USA. However, the characteristics of patients, including dietary habits, differ between Japan and the USA. The present study investigated the incidence of traffic accidents in CLD patients and the clinical profiles associated with traffic accidents in Japan using a data-mining analysis. A cross-sectional study was performed and 256 subjects [148 CLD patients (CLD group) and 106 patients with other digestive diseases (disease control group)] were enrolled; 2 patients were excluded. The incidence of traffic accidents was compared between the two groups. Independent factors for traffic accidents were analyzed using logistic regression and decision-tree analyses. The incidence of traffic accidents did not differ between the CLD and disease control groups (8.8 vs. 11.3%). The results of the logistic regression analysis showed that yoghurt consumption was the only independent risk factor for traffic accidents (odds ratio, 0.37; 95% confidence interval, 0.16–0.85; P=0.0197). Similarly, the results of the decision-tree analysis showed that yoghurt consumption was the initial divergence variable. In patients who consumed yoghurt habitually, the incidence of traffic accidents was 6.6%, while that in patients who did not consume yoghurt was 16.0%. CLD was not identified as an independent factor in the logistic regression and decision-tree analyses. In conclusion, the difference in the incidence of traffic accidents in Japan between the CLD and disease control groups was insignificant. Furthermore, yoghurt consumption was an independent negative risk factor for traffic accidents in patients with digestive diseases, including CLD. PMID:27123257

  8. An association between dietary habits and traffic accidents in patients with chronic liver disease: A data-mining analysis.

    PubMed

    Kawaguchi, Takumi; Suetsugu, Takuro; Ogata, Shyou; Imanaga, Minami; Ishii, Kumiko; Esaki, Nao; Sugimoto, Masako; Otsuyama, Jyuri; Nagamatsu, Ayu; Taniguchi, Eitaro; Itou, Minoru; Oriishi, Tetsuharu; Iwasaki, Shoko; Miura, Hiroko; Torimura, Takuji

    2016-05-01

    The incidence of traffic accidents in patients with chronic liver disease (CLD) is high in the USA. However, the characteristics of patients, including dietary habits, differ between Japan and the USA. The present study investigated the incidence of traffic accidents in CLD patients and the clinical profiles associated with traffic accidents in Japan using a data-mining analysis. A cross-sectional study was performed and 256 subjects [148 CLD patients (CLD group) and 106 patients with other digestive diseases (disease control group)] were enrolled; 2 patients were excluded. The incidence of traffic accidents was compared between the two groups. Independent factors for traffic accidents were analyzed using logistic regression and decision-tree analyses. The incidence of traffic accidents did not differ between the CLD and disease control groups (8.8 vs. 11.3%). The results of the logistic regression analysis showed that yoghurt consumption was the only independent risk factor for traffic accidents (odds ratio, 0.37; 95% confidence interval, 0.16-0.85; P=0.0197). Similarly, the results of the decision-tree analysis showed that yoghurt consumption was the initial divergence variable. In patients who consumed yoghurt habitually, the incidence of traffic accidents was 6.6%, while that in patients who did not consume yoghurt was 16.0%. CLD was not identified as an independent factor in the logistic regression and decision-tree analyses. In conclusion, the difference in the incidence of traffic accidents in Japan between the CLD and disease control groups was insignificant. Furthermore, yoghurt consumption was an independent negative risk factor for traffic accidents in patients with digestive diseases, including CLD.

  9. Analysis of traffic accident data in Kentucky (1995-1999)

    DOT National Transportation Integrated Search

    2000-09-01

    This report includes an analysis of traffic accidents data in Kentucky for the year 1995-1999. A primary objective of this study was to determined average and critical numbers and rates of accidents for various types of highways in rural and urban ar...

  10. Accident Analysis for the NIST Research Reactor Before and After Fuel Conversion

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Baek J.; Diamond D.; Cuadra, A.

    Postulated accidents have been analyzed for the 20 MW D2O-moderated research reactor (NBSR) at the National Institute of Standards and Technology (NIST). The analysis has been carried out for the present core, which contains high enriched uranium (HEU) fuel and for a proposed equilibrium core with low enriched uranium (LEU) fuel. The analyses employ state-of-the-art calculational methods. Three-dimensional Monte Carlo neutron transport calculations were performed with the MCNPX code to determine homogenized fuel compositions in the lower and upper halves of each fuel element and to determine the resulting neutronic properties of the core. The accident analysis employed a modelmore » of the primary loop with the RELAP5 code. The model includes the primary pumps, shutdown pumps outlet valves, heat exchanger, fuel elements, and flow channels for both the six inner and twenty-four outer fuel elements. Evaluations were performed for the following accidents: (1) control rod withdrawal startup accident, (2) maximum reactivity insertion accident, (3) loss-of-flow accident resulting from loss of electrical power with an assumption of failure of shutdown cooling pumps, (4) loss-of-flow accident resulting from a primary pump seizure, and (5) loss-of-flow accident resulting from inadvertent throttling of a flow control valve. In addition, natural circulation cooling at low power operation was analyzed. The analysis shows that the conversion will not lead to significant changes in the safety analysis and the calculated minimum critical heat flux ratio and maximum clad temperature assure that there is adequate margin to fuel failure.« less

  11. 'Remixing Rasmussen': The evolution of Accimaps within systemic accident analysis.

    PubMed

    Waterson, Patrick; Jenkins, Daniel P; Salmon, Paul M; Underwood, Peter

    2017-03-01

    Throughout Jens Rasmussen's career there has been a continued emphasis on the development of methods, techniques and tools for accident analysis and investigation. In this paper we focus on the evolution and development of one specific example, namely Accimaps and their use for accident analysis. We describe the origins of Accimaps followed by a review of 27 studies which have applied and adapted Accimaps over the period 2000-2015 to a range of domains and types of accident. Aside from demonstrating the versatility and popularity of the method, part of the motivation for the review of the use of Accimaps is to address the question of what constitutes a sound, usable, valid and reliable approach to systemic accident analysis. The findings from the review demonstrate continuity with the work carried out by Rasmussen, as well as significant variation (e.g., changes to the Accimap, used of additional theoretical and practice-oriented perspectives on safety). We conclude the paper with some speculations regarding future extension and adaptation of the Accimap approach including the possibility of using hybrid models for accident analysis. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Insights Gained from Forensic Analysis with MELCOR of the Fukushima-Daiichi Accidents.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Andrews, Nathan C.; Gauntt, Randall O.

    Since the accidents at Fukushima-Daiichi, Sandia National Laboratories has been modeling these accident scenarios using the severe accident analysis code, MELCOR. MELCOR is a widely used computer code developed at Sandia National Laboratories since ~1982 for the U.S. Nuclear Regulatory Commission. Insights from the modeling of these accidents is being used to better inform future code development and potentially improved accident management. To date, our necessity to better capture in-vessel thermal-hydraulic and ex-vessel melt coolability and concrete interactions has led to the implementation of new models. The most recent analyses, presented in this paper, have been in support of themore » of the Organization for Economic Cooperation and Development Nuclear Energy Agency’s (OECD/NEA) Benchmark Study of the Accident at the Fukushima Daiichi Nuclear Power Station (BSAF) Project. The goal of this project is to accurately capture the source term from all three releases and then model the atmospheric dispersion. In order to do this, a forensic approach is being used in which available plant data and release timings is being used to inform the modeled MELCOR accident scenario. For example, containment failures, core slumping events and lower head failure timings are all enforced parameters in these analyses. This approach is fundamentally different from a blind code assessment analysis often used in standard problem exercises. The timings of these events are informed by representative spikes or decreases in plant data. The combination of improvements to the MELCOR source code resulting from analysis previous accident analysis and this forensic approach has allowed Sandia to generate representative and plausible source terms for all three accidents at Fukushima Daiichi out to three weeks after the accident to capture both early and late releases. In particular, using the source terms developed by MELCOR, the MACCS software code, which models atmospheric dispersion and deposition, we are able to reasonably capture the deposition of radionuclides to the northwest of the reactor site.« less

  13. Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Farmer, Mitchell T.; Bunt, R.; Corradini, M.

    The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy’s (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affectmore » reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).« less

  14. Differences in Characteristics of Aviation Accidents during 1993-2012 Based on Flight Purpose

    NASA Technical Reports Server (NTRS)

    Evans, Joni K.

    2016-01-01

    Usually aviation accidents are categorized and analyzed within flight conduct rules (Part 121, Part 135, Part 91) because differences in accident rates within flight rules have been demonstrated. Even within a particular flight rule the flights have different purposes. For many, Part 121 flights are synonymous with scheduled passenger transport, and indeed this is the largest group of Part 121 accidents. But there are also non-scheduled (charter) passenger transport and cargo flights. The primary purpose of the analysis reported here is to examine the differences in aviation accidents based on the purpose of the flight. Some of the factors examined are the accident severity, aircraft characteristics and accident occurrence categories. Twenty consecutive years of data were available and utilized to complete this analysis.

  15. Development of multivariate exposure and fatal accident involvement rates for 1977

    DOT National Transportation Integrated Search

    1985-10-01

    The need for multivariate accident involvement rates is often encounted in : accident analysis. The FARS (Fatal Accident Reporting System) files contain : records of fatal involvements characterized by many variables while NPTS : (National Personal T...

  16. Work-Related Accidents and Sharp Injuries in Paramedics-Illustrated with an Example of a Multi-Specialist Hospital, Located in Central Poland.

    PubMed

    Garus-Pakowska, Anna; Szatko, Franciszek; Ulrichs, Magdalena

    2017-08-10

    (1) Background: An analysis of work-related accidents in paramedics in Poland by presenting the model and trend of accidents, accident rates and by identifying causes and results of accidents; (2) Methods: A retrospective analysis of medical documentation regarding work-related accidents in a multi-specialist hospital, located in central Poland, in the period 2005-2015. The study group included paramedics who had an accident while being on duty; (3) Results: According to hospital records, 88 paramedics were involved in 390 accidents and 265 injuries caused by sharp instruments. The annual accident rate was 5.34/100 employed paramedics. Most of the accidents occurred at night. The most common reason for the accident was careless behaviour of the paramedic, which resulted in joint sprains and dislocations. Injuries accounted for a huge portion of the total number of events. As many as 45% of injuries were not officially recorded; (4) Conclusion: High rates of work-related accidents and injuries caused by sharp instruments in paramedics are a serious public health problem. Further studies should be conducted in order to identify risk factors of accidents, particularly injuries, and to implement preventative programmes, aiming to minimise rates of occupational hazards for paramedics.

  17. Work-Related Accidents and Sharp Injuries in Paramedics—Illustrated with an Example of a Multi-Specialist Hospital, Located in Central Poland

    PubMed Central

    Szatko, Franciszek; Ulrichs, Magdalena

    2017-01-01

    (1) Background: An analysis of work-related accidents in paramedics in Poland by presenting the model and trend of accidents, accident rates and by identifying causes and results of accidents; (2) Methods: A retrospective analysis of medical documentation regarding work-related accidents in a multi-specialist hospital, located in central Poland, in the period 2005–2015. The study group included paramedics who had an accident while being on duty; (3) Results: According to hospital records, 88 paramedics were involved in 390 accidents and 265 injuries caused by sharp instruments. The annual accident rate was 5.34/100 employed paramedics. Most of the accidents occurred at night. The most common reason for the accident was careless behaviour of the paramedic, which resulted in joint sprains and dislocations. Injuries accounted for a huge portion of the total number of events. As many as 45% of injuries were not officially recorded; (4) Conclusion: High rates of work-related accidents and injuries caused by sharp instruments in paramedics are a serious public health problem. Further studies should be conducted in order to identify risk factors of accidents, particularly injuries, and to implement preventative programmes, aiming to minimise rates of occupational hazards for paramedics. PMID:28796193

  18. Utilization of accident databases and fuzzy sets to estimate frequency of HazMat transport accidents.

    PubMed

    Qiao, Yuanhua; Keren, Nir; Mannan, M Sam

    2009-08-15

    Risk assessment and management of transportation of hazardous materials (HazMat) require the estimation of accident frequency. This paper presents a methodology to estimate hazardous materials transportation accident frequency by utilizing publicly available databases and expert knowledge. The estimation process addresses route-dependent and route-independent variables. Negative binomial regression is applied to an analysis of the Department of Public Safety (DPS) accident database to derive basic accident frequency as a function of route-dependent variables, while the effects of route-independent variables are modeled by fuzzy logic. The integrated methodology provides the basis for an overall transportation risk analysis, which can be used later to develop a decision support system.

  19. Extended method of moments for deterministic analysis of stochastic multistable neurodynamical systems

    NASA Astrophysics Data System (ADS)

    Deco, Gustavo; Martí, Daniel

    2007-03-01

    The analysis of transitions in stochastic neurodynamical systems is essential to understand the computational principles that underlie those perceptual and cognitive processes involving multistable phenomena, like decision making and bistable perception. To investigate the role of noise in a multistable neurodynamical system described by coupled differential equations, one usually considers numerical simulations, which are time consuming because of the need for sufficiently many trials to capture the statistics of the influence of the fluctuations on that system. An alternative analytical approach involves the derivation of deterministic differential equations for the moments of the distribution of the activity of the neuronal populations. However, the application of the method of moments is restricted by the assumption that the distribution of the state variables of the system takes on a unimodal Gaussian shape. We extend in this paper the classical moments method to the case of bimodal distribution of the state variables, such that a reduced system of deterministic coupled differential equations can be derived for the desired regime of multistability.

  20. Nonclassical point of view of the Brownian motion generation via fractional deterministic model

    NASA Astrophysics Data System (ADS)

    Gilardi-Velázquez, H. E.; Campos-Cantón, E.

    In this paper, we present a dynamical system based on the Langevin equation without stochastic term and using fractional derivatives that exhibit properties of Brownian motion, i.e. a deterministic model to generate Brownian motion is proposed. The stochastic process is replaced by considering an additional degree of freedom in the second-order Langevin equation. Thus, it is transformed into a system of three first-order linear differential equations, additionally α-fractional derivative are considered which allow us to obtain better statistical properties. Switching surfaces are established as a part of fluctuating acceleration. The final system of three α-order linear differential equations does not contain a stochastic term, so the system generates motion in a deterministic way. Nevertheless, from the time series analysis, we found that the behavior of the system exhibits statistics properties of Brownian motion, such as, a linear growth in time of mean square displacement, a Gaussian distribution. Furthermore, we use the detrended fluctuation analysis to prove the Brownian character of this motion.

  1. Analysis of correlations and search for evidence of deterministic chaos in rhythmic motor control by the human brain

    NASA Astrophysics Data System (ADS)

    Roberts, Sean; Eykholt, R.; Thaut, Michael H.

    2000-08-01

    We investigate rhythmic finger tapping in both the presence and the absence of a metronome. We examine both the time intervals between taps and the time lags between the stimulus tones from the metronome and the response taps by the subject. We analyze the correlations in these data sets, and we search for evidence of deterministic chaos, as opposed to randomness, in the fluctuations.

  2. Major differences in rates of occupational accidents between different nationalities of seafarers.

    PubMed

    Hansen, Henrik L; Laursen, Lise Hedgaard; Frydberg, Morten; Kristensen, Soeren

    2008-01-01

    Earlier studies and statistics have shown that merchant seafarers from the South East Asia had considerable lower accident rates when compared with seafarers from Western Europe. The purposes of the study were to investigate whether the earlier observations were sustained if further sources on occurrence of accidents were used and to identify specific causes of excess accident rates among certain nationalities. Occupational accidents aboard Danish merchant ships during one year were identified from four different sources. These included accidents reported to the maritime authorities, accidents reported to a mutual insurance company, files on medical costs reimbursed by the government and finally, accidents in which there has been contact to the radio medical service. Time at risk aboard was obtained from a register on all employment periods aboard merchant ships. A total of 943 accidents causing personal injury to a seafarer directly caused by work aboard were identified. Among these accidents, 499 had taken place aboard cargo ships in international trade. Only these were used in the detailed analysis. The accident rate for all identified accidents aboard cargo ships were 84 accidents per 1,000 years aboard. The crude incidence rate ratio (IRR) for East European seafarers was 0.88 and for South East Asians 0.38 using West European seafarers as reference. In a Poisson regression analysis, the IRR for South East Asians was 0.29 (0.22-0.38). In an analysis including only more serious accidents, IRR for South East Asians rose to 0.36 (0.26-0.48). This study indicates that seafarers from South East Asia, mainly the Philippines, may have a genuine lower risk of occupational accidents in comparison with seafarers from Western and Eastern Europe. Differences in approach to safety and risk taking between South East Asian and European seafarers should be identified and positives attitudes included in accident preventing programmes. Main messages Seafarers from South East Asia, mainly the Philippines, seem to have a genuine lower risk of occupational accidents in comparison with seafarers from Western and Eastern Europe. Differences in approach to safety and risk taking between South East Asian and European seafarers should be identified and positives attitudes included in accident preventing programmes.

  3. An analysis of urban collisions using an artificial intelligence model.

    PubMed

    Mussone, L; Ferrari, A; Oneta, M

    1999-11-01

    Traditional studies on road accidents estimate the effect of variables (such as vehicular flows, road geometry, vehicular characteristics), and the calculation of the number of accidents. A descriptive statistical analysis of the accidents (those used in the model) over the period 1992-1995 is proposed. The paper describes an alternative method based on the use of artificial neural networks (ANN) in order to work out a model that relates to the analysis of vehicular accidents in Milan. The degree of danger of urban intersections using different scenarios is quantified by the ANN model. Methodology is the first result, which allows us to tackle the modelling of urban vehicular accidents by the innovative use of ANN. Other results deal with model outputs: intersection complexity may determine a higher accident index depending on the regulation of intersection. The highest index for running over of pedestrian occurs at non-signalised intersections at night-time.

  4. Accidents at work and costs analysis: a field study in a large Italian company.

    PubMed

    Battaglia, Massimo; Frey, Marco; Passetti, Emilio

    2014-01-01

    Accidents at work are still a heavy burden in social and economic terms, and action to improve health and safety standards at work offers great potential gains not only to employers, but also to individuals and society as a whole. However, companies often are not interested to measure the costs of accidents even if cost information may facilitate preventive occupational health and safety management initiatives. The field study, carried out in a large Italian company, illustrates technical and organisational aspects associated with the implementation of an accident costs analysis tool. The results indicate that the implementation (and the use) of the tool requires a considerable commitment by the company, that accident costs analysis should serve to reinforce the importance of health and safety prevention and that the economic dimension of accidents is substantial. The study also suggests practical ways to facilitate the implementation and the moral acceptance of the accounting technology.

  5. Accidents at Work and Costs Analysis: A Field Study in a Large Italian Company

    PubMed Central

    BATTAGLIA, Massimo; FREY, Marco; PASSETTI, Emilio

    2014-01-01

    Accidents at work are still a heavy burden in social and economic terms, and action to improve health and safety standards at work offers great potential gains not only to employers, but also to individuals and society as a whole. However, companies often are not interested to measure the costs of accidents even if cost information may facilitate preventive occupational health and safety management initiatives. The field study, carried out in a large Italian company, illustrates technical and organisational aspects associated with the implementation of an accident costs analysis tool. The results indicate that the implementation (and the use) of the tool requires a considerable commitment by the company, that accident costs analysis should serve to reinforce the importance of health and safety prevention and that the economic dimension of accidents is substantial. The study also suggests practical ways to facilitate the implementation and the moral acceptance of the accounting technology. PMID:24869894

  6. A spatial analysis of urban transit accidents assisted by Emergency Mobile Care Services: an analysis of space and time.

    PubMed

    Mendonça, Marcela Franklin Salvador de; Silva, Amanda Priscila de Santana Cabral; Castro, Claudia Cristina Lima de

    2017-01-01

    Urban transit accident are a global public health problem. The objective of this study was to describe the profile of the victims and the occurrences of urban transit accidents attended to by emergency mobile care services (Serviço de Atendimento Móvel de Urgência- SAMU) in Recife, and their distribution based on spatial analysis. An ecological study, developed through secondary data from emergency mobile care services in Recife, referring to the total number of occurrences of urban transit accidents attended to from January 1 to June 30, 2015. The spatial analysis was performed using the Moran index. Basic support units performed most of the emergency services (89.2%). Among the victims, there was a predominance of males (76.8%) and an age group of 20 - 29 years old (31.5%). Collisions were responsible for 59.9% of the transit accidents, and motorcycles for 61.6% of the accidents among all means of transportation. Friday was the day that showed the highest risk for treatment, and there was a concentration of events between 6:00 am - 8:59am and 6:00pm - 8:59pm. The MoranMap identified critical areas where calls came from traffic accidents during the period analyzed. The records of the mobile service from the spatial analysis are an important source of information for health surveillance. The spatial analysis of urban transit accidents identified regions with a positive spatial correlation, providing subsidies to the logistical planning of emergency mobile care services. This study is groundbreaking in that it offers such information about the region.

  7. Content analysis of 100 consecutive media reports of amusement ride accidents.

    PubMed

    Woodcock, Kathryn

    2008-01-01

    Accident investigations influence public perceptions and safety management strategies by determining the amount and type of information learned about the accident. To examine the factors considered in investigations, this study used a content analysis of 100 consecutive media reports of amusement ride accidents from an online media archive. Fatalities were overrepresented in the media dataset compared with U.S. national estimates. For analysis of reports, a modified "Haddon matrix" was developed using human-factors categories. This approach was useful to show differences between the proportions and types of factors considered in the different accident stages and between employee and rider accidents. Employee injury accounts primarily referred to the employee's task and to the employee. Rider injury reports were primarily related to the ride device itself and rarely referred to the rider's "task", social influences, or the rider's own actions, and only some reference to their characteristics. Qualitatively, it was evident that more human factors analysis is required to augment scant pre-failure information about the task, social environment, and the person, to make that information available for prevention of amusement ride accidents. By design, this study reflected information reported by the media. Future work will use the same techniques with official reports.

  8. [A spatially explicit analysis of traffic accidents involving pedestrians and cyclists in Berlin].

    PubMed

    Lakes, Tobia

    2017-12-01

    In many German cities and counties, sustainable mobility concepts that strengthen pedestrian and cyclist traffic are promoted. From the perspectives of urban development, traffic planning and public healthcare, a spatially differentiated analysis of traffic accident data is decisive. 1) The identification of spatial and temporal patterns of the distribution of accidents involving cyclists and pedestrians, 2) the identification of hotspots and exploration of possible underlying causes and 3) the critical discussion of benefits and challenges of the results and the derivation of conclusions. Spatio-temporal distributions of data from accident statistics in Berlin involving pedestrians and cyclists from 2011 to 2015 were analysed with geographic information systems (GIS). While the total number of accidents remains relatively stable for pedestrian and cyclist accidents, the spatial distribution analysis shows, however, that there are significant spatial clusters (hotspots) of traffic accidents with a strong concentration in the inner city area. In a critical discussion, the benefits of geographic concepts are identified, such as spatially explicit health data (in this case traffic accident data), the importance of the integration of other data sources for the evaluation of the health impact of areas (traffic accident statistics of the police), and the possibilities and limitations of spatial-temporal data analysis (spatial point-density analyses) for the derivation of decision-supported recommendations and for the evaluation of policy measures of health prevention and of health-relevant urban development.

  9. Association between Daily Hospital Outpatient Visits for Accidents and Daily Ambient Air Temperatures in an Industrial City.

    PubMed

    Chau, Tang-Tat; Wang, Kuo-Ying

    2016-01-01

    An accident is an unwanted hazard to a person. However, accidents occur. In this work, we search for correlations between daily accident rates and environmental factors. To study daily hospital outpatients who were admitted for accidents during a 5-year period, 2007-2011, we analyzed data regarding 168,366 outpatients using univariate regression models; we also used multivariable regression models to account for confounding factors. Our analysis indicates that the number of male outpatients admitted for accidents was approximately 1.31 to 1.47 times the number of female outpatients (P < 0.0001). Of the 12 parameters (regarding air pollution and meteorology) considered, only daily temperature exhibited consistent and significant correlations with the daily number of hospital outpatient visits for accidents throughout the 5-year analysis period. The univariate regression models indicate that older people (greater than 66 years old) had the fewest accidents per 1-degree increase in temperature, followed by young people (0-15 years old). Middle-aged people (16-65 years old) were the group of outpatients that were more prone to accidents, with an increase in accident rates of 0.8-1.2 accidents per degree increase in temperature. The multivariable regression models also reveal that the temperature variation was the dominant factor in determining the daily number of outpatient visits for accidents. Our further multivariable model analysis of temperature with respect to air pollution variables show that, through the increases in emissions and concentrations of CO, photochemical O3 production and NO2 loss in the ambient air, increases in vehicular emissions are associated with increases in temperatures. As such, increases in hospital visits for accidents are related to vehicular emissions and usage. This finding is consistent with clinical experience which shows about 60% to 80% of accidents are related to traffic, followed by accidents occurred in work place.

  10. Association between Daily Hospital Outpatient Visits for Accidents and Daily Ambient Air Temperatures in an Industrial City

    PubMed Central

    Chau, Tang-Tat; Wang, Kuo-Ying

    2016-01-01

    An accident is an unwanted hazard to a person. However, accidents occur. In this work, we search for correlations between daily accident rates and environmental factors. To study daily hospital outpatients who were admitted for accidents during a 5-year period, 2007–2011, we analyzed data regarding 168,366 outpatients using univariate regression models; we also used multivariable regression models to account for confounding factors. Our analysis indicates that the number of male outpatients admitted for accidents was approximately 1.31 to 1.47 times the number of female outpatients (P < 0.0001). Of the 12 parameters (regarding air pollution and meteorology) considered, only daily temperature exhibited consistent and significant correlations with the daily number of hospital outpatient visits for accidents throughout the 5-year analysis period. The univariate regression models indicate that older people (greater than 66 years old) had the fewest accidents per 1-degree increase in temperature, followed by young people (0–15 years old). Middle-aged people (16–65 years old) were the group of outpatients that were more prone to accidents, with an increase in accident rates of 0.8–1.2 accidents per degree increase in temperature. The multivariable regression models also reveal that the temperature variation was the dominant factor in determining the daily number of outpatient visits for accidents. Our further multivariable model analysis of temperature with respect to air pollution variables show that, through the increases in emissions and concentrations of CO, photochemical O3 production and NO2 loss in the ambient air, increases in vehicular emissions are associated with increases in temperatures. As such, increases in hospital visits for accidents are related to vehicular emissions and usage. This finding is consistent with clinical experience which shows about 60% to 80% of accidents are related to traffic, followed by accidents occurred in work place. PMID:26815039

  11. 23 CFR 658.11 - Additions, deletions, exceptions, and restrictions.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... analysis of suitability based on the criteria in § 658.9. (2) Proposals for additions that meet the... experiencing above normal accident rates and/or accident severities? Does analysis of the accident problem..., intersection geometrics and vulnerability of roadside hardware. (5) Is there a reasonable alternate route...

  12. Aircraft Loss-of-Control Accident Analysis

    NASA Technical Reports Server (NTRS)

    Belcastro, Christine M.; Foster, John V.

    2010-01-01

    Loss of control remains one of the largest contributors to fatal aircraft accidents worldwide. Aircraft loss-of-control accidents are complex in that they can result from numerous causal and contributing factors acting alone or (more often) in combination. Hence, there is no single intervention strategy to prevent these accidents. To gain a better understanding into aircraft loss-of-control events and possible intervention strategies, this paper presents a detailed analysis of loss-of-control accident data (predominantly from Part 121), including worst case combinations of causal and contributing factors and their sequencing. Future potential risks are also considered.

  13. Analysis of Two Electrocution Accidents in Greece that Occurred due to Unexpected Re-energization of Power Lines

    PubMed Central

    Baka, Aikaterini D.; Uzunoglu, Nikolaos K.

    2014-01-01

    Investigation and analysis of accidents are critical elements of safety management. The over-riding purpose of an organization in carrying out an accident investigation is to prevent similar accidents, as well as seek a general improvement in the management of health and safety. Hundreds of workers have suffered injuries while installing, maintaining, or servicing machinery and equipment due to sudden re-energization of power lines. This study presents and analyzes two electrical accidents (1 fatal injury and 1 serious injury) that occurred because the power supply was reconnected inadvertently or by mistake. PMID:25379331

  14. Analysis of Two Electrocution Accidents in Greece that Occurred due to Unexpected Re-energization of Power Lines.

    PubMed

    Baka, Aikaterini D; Uzunoglu, Nikolaos K

    2014-09-01

    Investigation and analysis of accidents are critical elements of safety management. The over-riding purpose of an organization in carrying out an accident investigation is to prevent similar accidents, as well as seek a general improvement in the management of health and safety. Hundreds of workers have suffered injuries while installing, maintaining, or servicing machinery and equipment due to sudden re-energization of power lines. This study presents and analyzes two electrical accidents (1 fatal injury and 1 serious injury) that occurred because the power supply was reconnected inadvertently or by mistake.

  15. Human error and commercial aviation accidents: an analysis using the human factors analysis and classification system.

    PubMed

    Shappell, Scott; Detwiler, Cristy; Holcomb, Kali; Hackworth, Carla; Boquet, Albert; Wiegmann, Douglas A

    2007-04-01

    The aim of this study was to extend previous examinations of aviation accidents to include specific aircrew, environmental, supervisory, and organizational factors associated with two types of commercial aviation (air carrier and commuter/ on-demand) accidents using the Human Factors Analysis and Classification System (HFACS). HFACS is a theoretically based tool for investigating and analyzing human error associated with accidents and incidents. Previous research has shown that HFACS can be reliably used to identify human factors trends associated with military and general aviation accidents. Using data obtained from both the National Transportation Safety Board and the Federal Aviation Administration, 6 pilot-raters classified aircrew, supervisory, organizational, and environmental causal factors associated with 1020 commercial aviation accidents that occurred over a 13-year period. The majority of accident causal factors were attributed to aircrew and the environment, with decidedly fewer associated with supervisory and organizational causes. Comparisons were made between HFACS causal categories and traditional situational variables such as visual conditions, injury severity, and regional differences. These data will provide support for the continuation, modification, and/or development of interventions aimed at commercial aviation safety. HFACS provides a tool for assessing human factors associated with accidents and incidents.

  16. Comparative study on neutronics characteristics of a 1500 MWe metal fuel sodium-cooled fast reactor

    DOE PAGES

    Ohgama, Kazuya; Aliberti, Gerardo; Stauff, Nicolas E.; ...

    2017-02-28

    Under the cooperative effort of the Civil Nuclear Energy R&D Working Group within the framework of the U.S.-Japan bilateral, Argonne National Laboratory (ANL) and Japan Atomic Energy Agency (JAEA) have been performing benchmark study using Japan Sodium-cooled Fast Reactor (JSFR) design with metal fuel. In this benchmark study, core characteristic parameters at the beginning of cycle were evaluated by the best estimate deterministic and stochastic methodologies of ANL and JAEA. The results obtained by both institutions show a good agreement with less than 200 pcm of discrepancy on the neutron multiplication factor, and less than 3% of discrepancy on themore » sodium void reactivity, Doppler reactivity, and control rod worth. The results by the stochastic and deterministic approaches were compared in each party to investigate impacts of the deterministic approximation and to understand potential variations in the results due to different calculation methodologies employed. From the detailed analysis of methodologies, it was found that the good agreement in multiplication factor from the deterministic calculations comes from the cancellation of the differences on the methodology (0.4%) and nuclear data (0.6%). The different treatment in reflector cross section generation was estimated as the major cause of the discrepancy between the multiplication factors by the JAEA and ANL deterministic methodologies. Impacts of the nuclear data libraries were also investigated using a sensitivity analysis methodology. Furthermore, the differences on the inelastic scattering cross sections of U-238, ν values and fission cross sections of Pu-239 and µ-average of Na-23 are the major contributors to the difference on the multiplication factors.« less

  17. Comparative study on neutronics characteristics of a 1500 MWe metal fuel sodium-cooled fast reactor

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ohgama, Kazuya; Aliberti, Gerardo; Stauff, Nicolas E.

    Under the cooperative effort of the Civil Nuclear Energy R&D Working Group within the framework of the U.S.-Japan bilateral, Argonne National Laboratory (ANL) and Japan Atomic Energy Agency (JAEA) have been performing benchmark study using Japan Sodium-cooled Fast Reactor (JSFR) design with metal fuel. In this benchmark study, core characteristic parameters at the beginning of cycle were evaluated by the best estimate deterministic and stochastic methodologies of ANL and JAEA. The results obtained by both institutions show a good agreement with less than 200 pcm of discrepancy on the neutron multiplication factor, and less than 3% of discrepancy on themore » sodium void reactivity, Doppler reactivity, and control rod worth. The results by the stochastic and deterministic approaches were compared in each party to investigate impacts of the deterministic approximation and to understand potential variations in the results due to different calculation methodologies employed. From the detailed analysis of methodologies, it was found that the good agreement in multiplication factor from the deterministic calculations comes from the cancellation of the differences on the methodology (0.4%) and nuclear data (0.6%). The different treatment in reflector cross section generation was estimated as the major cause of the discrepancy between the multiplication factors by the JAEA and ANL deterministic methodologies. Impacts of the nuclear data libraries were also investigated using a sensitivity analysis methodology. Furthermore, the differences on the inelastic scattering cross sections of U-238, ν values and fission cross sections of Pu-239 and µ-average of Na-23 are the major contributors to the difference on the multiplication factors.« less

  18. Motorcycle accident cause factors and identification of countermeasures. Volume 1 : technical report

    DOT National Transportation Integrated Search

    1981-01-01

    This report presents the data and find~ings from the on-scene, in-depth : investigations of 900 motorcycle accidents and the analysis of 3600 traffic : accident reports of motorcycle accidents in the same study area. : Comprehensive data were collect...

  19. Motorcycle accident cause factors and identification of countermeasures. Volume 2 : appendix/supplemental data

    DOT National Transportation Integrated Search

    1981-01-01

    This report presents the data and findings from the on-scene, in-depth : investigations of 900 motorcycle accidents and the analysis of 3600 traffic : accident reports of motorcycle accidents in the same study area. : Comprehensive data were collecte...

  20. Spatiotemporal characteristics of elderly population’s traffic accidents in Seoul using space-time cube and space-time kernel density estimation

    PubMed Central

    Cho, Nahye; Son, Serin

    2018-01-01

    The purpose of this study is to analyze how the spatiotemporal characteristics of traffic accidents involving the elderly population in Seoul are changing by time period. We applied kernel density estimation and hotspot analyses to analyze the spatial characteristics of elderly people’s traffic accidents, and the space-time cube, emerging hotspot, and space-time kernel density estimation analyses to analyze the spatiotemporal characteristics. In addition, we analyzed elderly people’s traffic accidents by dividing cases into those in which the drivers were elderly people and those in which elderly people were victims of traffic accidents, and used the traffic accidents data in Seoul for 2013 for analysis. The main findings were as follows: (1) the hotspots for elderly people’s traffic accidents differed according to whether they were drivers or victims. (2) The hourly analysis showed that the hotspots for elderly drivers’ traffic accidents are in specific areas north of the Han River during the period from morning to afternoon, whereas the hotspots for elderly victims are distributed over a wide area from daytime to evening. (3) Monthly analysis showed that the hotspots are weak during winter and summer, whereas they are strong in the hiking and climbing areas in Seoul during spring and fall. Further, elderly victims’ hotspots are more sporadic than elderly drivers’ hotspots. (4) The analysis for the entire period of 2013 indicates that traffic accidents involving elderly people are increasing in specific areas on the north side of the Han River. We expect the results of this study to aid in reducing the number of traffic accidents involving elderly people in the future. PMID:29768453

  1. Spatiotemporal characteristics of elderly population's traffic accidents in Seoul using space-time cube and space-time kernel density estimation.

    PubMed

    Kang, Youngok; Cho, Nahye; Son, Serin

    2018-01-01

    The purpose of this study is to analyze how the spatiotemporal characteristics of traffic accidents involving the elderly population in Seoul are changing by time period. We applied kernel density estimation and hotspot analyses to analyze the spatial characteristics of elderly people's traffic accidents, and the space-time cube, emerging hotspot, and space-time kernel density estimation analyses to analyze the spatiotemporal characteristics. In addition, we analyzed elderly people's traffic accidents by dividing cases into those in which the drivers were elderly people and those in which elderly people were victims of traffic accidents, and used the traffic accidents data in Seoul for 2013 for analysis. The main findings were as follows: (1) the hotspots for elderly people's traffic accidents differed according to whether they were drivers or victims. (2) The hourly analysis showed that the hotspots for elderly drivers' traffic accidents are in specific areas north of the Han River during the period from morning to afternoon, whereas the hotspots for elderly victims are distributed over a wide area from daytime to evening. (3) Monthly analysis showed that the hotspots are weak during winter and summer, whereas they are strong in the hiking and climbing areas in Seoul during spring and fall. Further, elderly victims' hotspots are more sporadic than elderly drivers' hotspots. (4) The analysis for the entire period of 2013 indicates that traffic accidents involving elderly people are increasing in specific areas on the north side of the Han River. We expect the results of this study to aid in reducing the number of traffic accidents involving elderly people in the future.

  2. HyRAM V1.0 User Guide

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Groth, Katrina M.; Zumwalt, Hannah Ruth; Clark, Andrew Jordan

    2016-03-01

    Hydrogen Risk Assessment Models (HyRAM) is a prototype software toolkit that integrates data and methods relevant to assessing the safety of hydrogen fueling and storage infrastructure. The HyRAM toolkit integrates deterministic and probabilistic models for quantifying accident scenarios, predicting physical effects, and characterizing the impact of hydrogen hazards, including thermal effects from jet fires and thermal pressure effects from deflagration. HyRAM version 1.0 incorporates generic probabilities for equipment failures for nine types of components, and probabilistic models for the impact of heat flux on humans and structures, with computationally and experimentally validated models of various aspects of gaseous hydrogen releasemore » and flame physics. This document provides an example of how to use HyRAM to conduct analysis of a fueling facility. This document will guide users through the software and how to enter and edit certain inputs that are specific to the user-defined facility. Description of the methodology and models contained in HyRAM is provided in [1]. This User’s Guide is intended to capture the main features of HyRAM version 1.0 (any HyRAM version numbered as 1.0.X.XXX). This user guide was created with HyRAM 1.0.1.798. Due to ongoing software development activities, newer versions of HyRAM may have differences from this guide.« less

  3. The Application of Deterministic Spectral Domain Method to the Analysis of Planar Circuit Discontinuities on Open Substrates

    DTIC Science & Technology

    1990-08-01

    the spectral domain is extended to include the effects of two-dimensional, two-component current flow in planar transmission line discontinuities 6n...PROFESSOR: Tatsuo Itoh A deterministic formulation of the method of moments carried out in the spectral domain is extended to include the effects of...two-dimensional, two- component current flow in planar transmission line discontinuities on open substrates. The method includes the effects of space

  4. ACCELERATING FUSION REACTOR NEUTRONICS MODELING BY AUTOMATIC COUPLING OF HYBRID MONTE CARLO/DETERMINISTIC TRANSPORT ON CAD GEOMETRY

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Biondo, Elliott D; Ibrahim, Ahmad M; Mosher, Scott W

    2015-01-01

    Detailed radiation transport calculations are necessary for many aspects of the design of fusion energy systems (FES) such as ensuring occupational safety, assessing the activation of system components for waste disposal, and maintaining cryogenic temperatures within superconducting magnets. Hybrid Monte Carlo (MC)/deterministic techniques are necessary for this analysis because FES are large, heavily shielded, and contain streaming paths that can only be resolved with MC. The tremendous complexity of FES necessitates the use of CAD geometry for design and analysis. Previous ITER analysis has required the translation of CAD geometry to MCNP5 form in order to use the AutomateD VAriaNcemore » reducTion Generator (ADVANTG) for hybrid MC/deterministic transport. In this work, ADVANTG was modified to support CAD geometry, allowing hybrid (MC)/deterministic transport to be done automatically and eliminating the need for this translation step. This was done by adding a new ray tracing routine to ADVANTG for CAD geometries using the Direct Accelerated Geometry Monte Carlo (DAGMC) software library. This new capability is demonstrated with a prompt dose rate calculation for an ITER computational benchmark problem using both the Consistent Adjoint Driven Importance Sampling (CADIS) method an the Forward Weighted (FW)-CADIS method. The variance reduction parameters produced by ADVANTG are shown to be the same using CAD geometry and standard MCNP5 geometry. Significant speedups were observed for both neutrons (as high as a factor of 7.1) and photons (as high as a factor of 59.6).« less

  5. SOARCA Peach Bottom Atomic Power Station Long-Term Station Blackout Uncertainty Analysis: Knowledge Advancement.

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gauntt, Randall O.; Mattie, Patrick D.; Bixler, Nathan E.

    2014-02-01

    This paper describes the knowledge advancements from the uncertainty analysis for the State-of- the-Art Reactor Consequence Analyses (SOARCA) unmitigated long-term station blackout accident scenario at the Peach Bottom Atomic Power Station. This work assessed key MELCOR and MELCOR Accident Consequence Code System, Version 2 (MACCS2) modeling uncertainties in an integrated fashion to quantify the relative importance of each uncertain input on potential accident progression, radiological releases, and off-site consequences. This quantitative uncertainty analysis provides measures of the effects on consequences, of each of the selected uncertain parameters both individually and in interaction with other parameters. The results measure the modelmore » response (e.g., variance in the output) to uncertainty in the selected input. Investigation into the important uncertain parameters in turn yields insights into important phenomena for accident progression and off-site consequences. This uncertainty analysis confirmed the known importance of some parameters, such as failure rate of the Safety Relief Valve in accident progression modeling and the dry deposition velocity in off-site consequence modeling. The analysis also revealed some new insights, such as dependent effect of cesium chemical form for different accident progressions. (auth)« less

  6. Management system of health and safety work (SMK3) with job safety analysis (JSA) in PT. Nira Murni construction

    NASA Astrophysics Data System (ADS)

    Melliana, Armen, Yusrizal, Akmal, Syarifah

    2017-11-01

    PT Nira Murni construction is a contractor of PT Chevron Pacific Indonesia which engaged in contractor, fabrication, maintenance construction suppliers, and labor services. The high of accident rate in this company is caused the lack of awareness of workplace safety. Therefore, it requires an effort to reduce the accident rate on the company so that the financial losses can be minimized. In this study, Safe T-Score method is used to analyze the accident rate by measuring the level of frequency. Analysis is continued using risk management methods which identify hazards, risk measurement and risk management. The last analysis uses Job safety analysis (JSA) which will identify the effect of accidents. From the result of this study can be concluded that Job Safety Analysis (JSA) methods has not been implemented properly. Therefore, JSA method needs to follow-up in the next study, so that can be well applied as prevention of occupational accidents.

  7. A summary of unmanned aircraft accident/incident data : human factors implications

    DOT National Transportation Integrated Search

    2004-12-01

    A review and analysis of unmanned aircraft (UA) accident data was conducted to identify important human factors issues related to their use. UA accident data were collected from the U.S. Army, Navy, and Air Force. Classification of the accident data ...

  8. Glider accidents: an analysis of 143 cases, 2001-2005.

    PubMed

    van Doorn, Robert R A; de Voogt, Alexander J

    2007-01-01

    The majority of aviation crashes and casualties take place in general and sport aviation. Although gliding has gained popularity in recent decades, we could find no systematic analysis of glider accidents. This study determined factors associated with both non-fatal and fatal glider accidents to document their position within sport and general aviation accidents, and to suggest preventive measures and improvements. We performed a retrospective review of glider accidents for the period 2001-2005 in the database maintained by the U.S. National Transportation Safety Board (NTSB). A total of 117 non-fatal and 26 fatal glider accidents were reported for the 5-yr period. Adverse weather was the cause in 20% of all non-fatal accidents, 60% of which occurred in the cruise phase. Logistic regression revealed that fatal accidents were predicted by pilot error, flight phase, and home-built aircraft. Factors contributing to glider crashes are specific to this type of sport aviation. Owners of home-built gliders should pay particular attention to the aircraft's specifications and design limits.

  9. Methods for nuclear air-cleaning-system accident-consequence assessment

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Andrae, R.W.; Bolstad, J.W.; Gregory, W.S.

    1982-01-01

    This paper describes a multilaboratory research program that is directed toward addressing many questions that analysts face when performing air cleaning accident consequence assessments. The program involves developing analytical tools and supportive experimental data that will be useful in making more realistic assessments of accident source terms within and up to the atmospheric boundaries of nuclear fuel cycle facilities. The types of accidents considered in this study includes fires, explosions, spills, tornadoes, criticalities, and equipment failures. The main focus of the program is developing an accident analysis handbook (AAH). We will describe the contents of the AAH, which include descriptionsmore » of selected nuclear fuel cycle facilities, process unit operations, source-term development, and accident consequence analyses. Three computer codes designed to predict gas and material propagation through facility air cleaning systems are described. These computer codes address accidents involving fires (FIRAC), explosions (EXPAC), and tornadoes (TORAC). The handbook relies on many illustrative examples to show the analyst how to approach accident consequence assessments. We will use the FIRAC code and a hypothetical fire scenario to illustrate the accident analysis capability.« less

  10. The Human Factors of an Early Space Accident: Flight 3-65 of the X-15

    NASA Technical Reports Server (NTRS)

    Barshi, Immanuel; Statler, Irving C.; Orr, Jeb S.

    2015-01-01

    The X-15 was a critical research vehicle in the early days of space flight. On November 15, 1967, the X-15-3 suffered an in-flight breakup. This 191st flight of the X-15 and the 65th flight of this third configuration was the only fatal accident of the X-15 program. This paper presents an analysis, from a human factors perspective, of the events that led up to the accident. The analysis is based on the information contained in the report of the Air Force-NASA Accident Investigation Board (AIB) dated January, 1968. The AIBs analysis addressed, primarily, the events that occurred subsequent to the pilots taking direct control of the reaction control system. The analysis described here suggests that all of the events that caused the accident occurred well before the moment when the pilot switched to direct control. Consequently, the analyses and conclusions regarding the causal factors of, and the contributing factors to, the loss of Flight 3-65 presented here differ from those of the AIB based on the same evidence. Although the accident occurred in 1967, the results of the presented analysis are still relevant today. We present our analysis and discuss its implications for the safety of space operations.

  11. The Human Factors of an Early Space Accident: Flight 3-65 of the X-15

    NASA Technical Reports Server (NTRS)

    Barshi, Immanuel; Statler, Irving C.; Orr, Jeb S.

    2016-01-01

    The X-15 was a critical research vehicle in the early days of space flight. On November 15, 1967, the X-15-3 suffered an in-flight breakup. This 191st flight of the X-15 and the 65th flight of this third configuration was the only fatal accident of the X-15 program. This paper presents an analysis, from a human factors perspective, of the events that led up to the accident. The analysis is based on the information contained in the report of the Air Force-NASA Accident Investigation Board (AIB) dated January, 1968. The AIBs analysis addressed, primarily, the events that occurred subsequent to the pilot's taking direct control of the reaction control system. The analysis described here suggests that, rather than events following the pilot's switch to direct control, it was the events preceding the switch that led to the accident. Consequently, the analyses and conclusions regarding the causal factors of, and the contributing factors to, the loss of Flight 3-65 presented here differ from those of the AIB based on the same evidence. Although the accident occurred in 1967, the results of the presented analysis are still relevant today. We present our analysis and discuss its implications for the safety of space operations.

  12. Churchill: an ultra-fast, deterministic, highly scalable and balanced parallelization strategy for the discovery of human genetic variation in clinical and population-scale genomics.

    PubMed

    Kelly, Benjamin J; Fitch, James R; Hu, Yangqiu; Corsmeier, Donald J; Zhong, Huachun; Wetzel, Amy N; Nordquist, Russell D; Newsom, David L; White, Peter

    2015-01-20

    While advances in genome sequencing technology make population-scale genomics a possibility, current approaches for analysis of these data rely upon parallelization strategies that have limited scalability, complex implementation and lack reproducibility. Churchill, a balanced regional parallelization strategy, overcomes these challenges, fully automating the multiple steps required to go from raw sequencing reads to variant discovery. Through implementation of novel deterministic parallelization techniques, Churchill allows computationally efficient analysis of a high-depth whole genome sample in less than two hours. The method is highly scalable, enabling full analysis of the 1000 Genomes raw sequence dataset in a week using cloud resources. http://churchill.nchri.org/.

  13. A case study analysis to examine motorcycle crashes in Bogota, Colombia.

    PubMed

    Jimenez, Adriana; Bocarejo, Juan Pablo; Zarama, Roberto; Yerpez, Joël

    2015-02-01

    Contributory factors to motorcycle crashes vary among populations depending on several aspects such as the users' profiles, the composition and density of traffic, and the infrastructure features. A better understanding of local motorcycle crashes can be reached in those places where a comprehensive analysis is performed. This paper presents the results obtained from a case study analysis of 400 police records of accidents involving motorcycles in Bogota. To achieve a deeper level of understanding of how these accidents occur, we propose a systemic approach that uses available crash data. The methodology is inspired by accident prototypical scenarios, a tool for analysis developed in France. When grouping cases we identified three categories: solo motorcycle accidents, motorcyclist and pedestrian accidents, and accidents involving a motorcycle and another vehicle. Within these categories we undertook in-depth analyses of 32 groups of accidents obtaining valuable information to better comprehend motorcyclists' road crashes in a local context. Recurrent contributory factors in the groups of accidents include: inexperienced motorcyclists, wide urban roads that incite speeding and risky overtaking maneuvers, flowing urban roads that encourage high speed and increased interaction between vehicles, and lack of infrastructure maintenance. The results obtained are a valuable asset to define measures that will be conveniently adapted to the group of accident on which we want to act. The methodology exposed in this paper is applicable to the study of road crashes that involve all types of actors, not only the motorcyclists, and in contexts different than those presented in Bogota. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

  14. Realistic Simulation for Body Area and Body-To-Body Networks

    PubMed Central

    Alam, Muhammad Mahtab; Ben Hamida, Elyes; Ben Arbia, Dhafer; Maman, Mickael; Mani, Francesco; Denis, Benoit; D’Errico, Raffaele

    2016-01-01

    In this paper, we present an accurate and realistic simulation for body area networks (BAN) and body-to-body networks (BBN) using deterministic and semi-deterministic approaches. First, in the semi-deterministic approach, a real-time measurement campaign is performed, which is further characterized through statistical analysis. It is able to generate link-correlated and time-varying realistic traces (i.e., with consistent mobility patterns) for on-body and body-to-body shadowing and fading, including body orientations and rotations, by means of stochastic channel models. The full deterministic approach is particularly targeted to enhance IEEE 802.15.6 proposed channel models by introducing space and time variations (i.e., dynamic distances) through biomechanical modeling. In addition, it helps to accurately model the radio link by identifying the link types and corresponding path loss factors for line of sight (LOS) and non-line of sight (NLOS). This approach is particularly important for links that vary over time due to mobility. It is also important to add that the communication and protocol stack, including the physical (PHY), medium access control (MAC) and networking models, is developed for BAN and BBN, and the IEEE 802.15.6 compliance standard is provided as a benchmark for future research works of the community. Finally, the two approaches are compared in terms of the successful packet delivery ratio, packet delay and energy efficiency. The results show that the semi-deterministic approach is the best option; however, for the diversity of the mobility patterns and scenarios applicable, biomechanical modeling and the deterministic approach are better choices. PMID:27104537

  15. Realistic Simulation for Body Area and Body-To-Body Networks.

    PubMed

    Alam, Muhammad Mahtab; Ben Hamida, Elyes; Ben Arbia, Dhafer; Maman, Mickael; Mani, Francesco; Denis, Benoit; D'Errico, Raffaele

    2016-04-20

    In this paper, we present an accurate and realistic simulation for body area networks (BAN) and body-to-body networks (BBN) using deterministic and semi-deterministic approaches. First, in the semi-deterministic approach, a real-time measurement campaign is performed, which is further characterized through statistical analysis. It is able to generate link-correlated and time-varying realistic traces (i.e., with consistent mobility patterns) for on-body and body-to-body shadowing and fading, including body orientations and rotations, by means of stochastic channel models. The full deterministic approach is particularly targeted to enhance IEEE 802.15.6 proposed channel models by introducing space and time variations (i.e., dynamic distances) through biomechanical modeling. In addition, it helps to accurately model the radio link by identifying the link types and corresponding path loss factors for line of sight (LOS) and non-line of sight (NLOS). This approach is particularly important for links that vary over time due to mobility. It is also important to add that the communication and protocol stack, including the physical (PHY), medium access control (MAC) and networking models, is developed for BAN and BBN, and the IEEE 802.15.6 compliance standard is provided as a benchmark for future research works of the community. Finally, the two approaches are compared in terms of the successful packet delivery ratio, packet delay and energy efficiency. The results show that the semi-deterministic approach is the best option; however, for the diversity of the mobility patterns and scenarios applicable, biomechanical modeling and the deterministic approach are better choices.

  16. Analysis of construction accidents in Spain, 2003-2008.

    PubMed

    López Arquillos, Antonio; Rubio Romero, Juan Carlos; Gibb, Alistair

    2012-12-01

    The research objective for this paper is to obtain a new extended and updated insight to the likely causes of construction accidents in Spain, in order to identify suitable mitigating actions. The paper analyzes all construction sector accidents in Spain between 2003 and 2008. Ten variables were chosen and the influence of each variable is evaluated with respect to the severity of the accident. The descriptive analysis is based on a total of 1,163,178 accidents. Results showed that the severity of accidents was related to variables including age, CNAE (National Classification of Economic Activities) code, size of company, length of service, location of accident, day of the week, days of absence, deviation, injury, and climatic zones. According to data analyzed, a large company is not always necessarily safer than a small company in the aspect of fatal accidents, experienced workers do not have the best accident fatality rates, and accidents occurring away from the usual workplace had more severe consequences. Results obtained in this paper can be used by companies in their occupational safety strategies, and in their safety training programs. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

  17. Introduction of Bayesian network in risk analysis of maritime accidents in Bangladesh

    NASA Astrophysics Data System (ADS)

    Rahman, Sohanur

    2017-12-01

    Due to the unique geographic location, complex navigation environment and intense vessel traffic, a considerable number of maritime accidents occurred in Bangladesh which caused serious loss of life, property and environmental contamination. Based on the historical data of maritime accidents from 1981 to 2015, which has been collected from Department of Shipping (DOS) and Bangladesh Inland Water Transport Authority (BIWTA), this paper conducted a risk analysis of maritime accidents by applying Bayesian network. In order to conduct this study, a Bayesian network model has been developed to find out the relation among parameters and the probability of them which affect accidents based on the accident investigation report of Bangladesh. Furthermore, number of accidents in different categories has also been investigated in this paper. Finally, some viable recommendations have been proposed in order to ensure greater safety of inland vessels in Bangladesh.

  18. Analysis of Convair 990 rejected-takeoff accident with emphasis on decision making, training and procedures

    NASA Technical Reports Server (NTRS)

    Batthauer, Byron E.

    1987-01-01

    This paper analyzes a NASA Convair 990 (CV-990) accident with emphasis on rejected-takeoff (RTO) decision making, training, procedures, and accident statistics. The NASA Aircraft Accident Investigation Board was somewhat perplexed that an aircraft could be destroyed as a result of blown tires during the takeoff roll. To provide a better understanding of tire failure RTO's, The Board obtained accident reports, Federal Aviation Administration (FAA) studies, and other pertinent information related to the elements of this accident. This material enhanced the analysis process and convinced the Accident Board that high-speed RTO's in transport aircraft should be given more emphasis during pilot training. Pilots should be made aware of various RTO situations and statistics with emphasis on failed-tire RTO's. This background information could enhance the split-second decision-making process that is required prior to initiating an RTO.

  19. Work-related accidents among the Iranian population: a time series analysis, 2000–2011

    PubMed Central

    Karimlou, Masoud; Imani, Mehdi; Hosseini, Agha-Fatemeh; Dehnad, Afsaneh; Vahabi, Nasim; Bakhtiyari, Mahmood

    2015-01-01

    Background Work-related accidents result in human suffering and economic losses and are considered as a major health problem worldwide, especially in the economically developing world. Objectives To introduce seasonal autoregressive moving average (ARIMA) models for time series analysis of work-related accident data for workers insured by the Iranian Social Security Organization (ISSO) between 2000 and 2011. Methods In this retrospective study, all insured people experiencing at least one work-related accident during a 10-year period were included in the analyses. We used Box–Jenkins modeling to develop a time series model of the total number of accidents. Results There was an average of 1476 accidents per month (1476·05±458·77, mean±SD). The final ARIMA (p,d,q) (P,D,Q)s model for fitting to data was: ARIMA(1,1,1)×(0,1,1)12 consisting of the first ordering of the autoregressive, moving average and seasonal moving average parameters with 20·942 mean absolute percentage error (MAPE). Conclusions The final model showed that time series analysis of ARIMA models was useful for forecasting the number of work-related accidents in Iran. In addition, the forecasted number of work-related accidents for 2011 explained the stability of occurrence of these accidents in recent years, indicating a need for preventive occupational health and safety policies such as safety inspection. PMID:26119774

  20. Work-related accidents among the Iranian population: a time series analysis, 2000-2011.

    PubMed

    Karimlou, Masoud; Salehi, Masoud; Imani, Mehdi; Hosseini, Agha-Fatemeh; Dehnad, Afsaneh; Vahabi, Nasim; Bakhtiyari, Mahmood

    2015-01-01

    Work-related accidents result in human suffering and economic losses and are considered as a major health problem worldwide, especially in the economically developing world. To introduce seasonal autoregressive moving average (ARIMA) models for time series analysis of work-related accident data for workers insured by the Iranian Social Security Organization (ISSO) between 2000 and 2011. In this retrospective study, all insured people experiencing at least one work-related accident during a 10-year period were included in the analyses. We used Box-Jenkins modeling to develop a time series model of the total number of accidents. There was an average of 1476 accidents per month (1476·05±458·77, mean±SD). The final ARIMA (p,d,q) (P,D,Q)s model for fitting to data was: ARIMA(1,1,1)×(0,1,1)12 consisting of the first ordering of the autoregressive, moving average and seasonal moving average parameters with 20·942 mean absolute percentage error (MAPE). The final model showed that time series analysis of ARIMA models was useful for forecasting the number of work-related accidents in Iran. In addition, the forecasted number of work-related accidents for 2011 explained the stability of occurrence of these accidents in recent years, indicating a need for preventive occupational health and safety policies such as safety inspection.

  1. Probabilistic sensitivity analysis incorporating the bootstrap: an example comparing treatments for the eradication of Helicobacter pylori.

    PubMed

    Pasta, D J; Taylor, J L; Henning, J M

    1999-01-01

    Decision-analytic models are frequently used to evaluate the relative costs and benefits of alternative therapeutic strategies for health care. Various types of sensitivity analysis are used to evaluate the uncertainty inherent in the models. Although probabilistic sensitivity analysis is more difficult theoretically and computationally, the results can be much more powerful and useful than deterministic sensitivity analysis. The authors show how a Monte Carlo simulation can be implemented using standard software to perform a probabilistic sensitivity analysis incorporating the bootstrap. The method is applied to a decision-analytic model evaluating the cost-effectiveness of Helicobacter pylori eradication. The necessary steps are straightforward and are described in detail. The use of the bootstrap avoids certain difficulties encountered with theoretical distributions. The probabilistic sensitivity analysis provided insights into the decision-analytic model beyond the traditional base-case and deterministic sensitivity analyses and should become the standard method for assessing sensitivity.

  2. CPT-based probabilistic and deterministic assessment of in situ seismic soil liquefaction potential

    USGS Publications Warehouse

    Moss, R.E.S.; Seed, R.B.; Kayen, R.E.; Stewart, J.P.; Der Kiureghian, A.; Cetin, K.O.

    2006-01-01

    This paper presents a complete methodology for both probabilistic and deterministic assessment of seismic soil liquefaction triggering potential based on the cone penetration test (CPT). A comprehensive worldwide set of CPT-based liquefaction field case histories were compiled and back analyzed, and the data then used to develop probabilistic triggering correlations. Issues investigated in this study include improved normalization of CPT resistance measurements for the influence of effective overburden stress, and adjustment to CPT tip resistance for the potential influence of "thin" liquefiable layers. The effects of soil type and soil character (i.e., "fines" adjustment) for the new correlations are based on a combination of CPT tip and sleeve resistance. To quantify probability for performancebased engineering applications, Bayesian "regression" methods were used, and the uncertainties of all variables comprising both the seismic demand and the liquefaction resistance were estimated and included in the analysis. The resulting correlations were developed using a Bayesian framework and are presented in both probabilistic and deterministic formats. The results are compared to previous probabilistic and deterministic correlations. ?? 2006 ASCE.

  3. Precision production: enabling deterministic throughput for precision aspheres with MRF

    NASA Astrophysics Data System (ADS)

    Maloney, Chris; Entezarian, Navid; Dumas, Paul

    2017-10-01

    Aspherical lenses offer advantages over spherical optics by improving image quality or reducing the number of elements necessary in an optical system. Aspheres are no longer being used exclusively by high-end optical systems but are now replacing spherical optics in many applications. The need for a method of production-manufacturing of precision aspheres has emerged and is part of the reason that the optics industry is shifting away from artisan-based techniques towards more deterministic methods. Not only does Magnetorheological Finishing (MRF) empower deterministic figure correction for the most demanding aspheres but it also enables deterministic and efficient throughput for series production of aspheres. The Q-flex MRF platform is designed to support batch production in a simple and user friendly manner. Thorlabs routinely utilizes the advancements of this platform and has provided results from using MRF to finish a batch of aspheres as a case study. We have developed an analysis notebook to evaluate necessary specifications for implementing quality control metrics. MRF brings confidence to optical manufacturing by ensuring high throughput for batch processing of aspheres.

  4. A comprehensive probabilistic analysis model of oil pipelines network based on Bayesian network

    NASA Astrophysics Data System (ADS)

    Zhang, C.; Qin, T. X.; Jiang, B.; Huang, C.

    2018-02-01

    Oil pipelines network is one of the most important facilities of energy transportation. But oil pipelines network accident may result in serious disasters. Some analysis models for these accidents have been established mainly based on three methods, including event-tree, accident simulation and Bayesian network. Among these methods, Bayesian network is suitable for probabilistic analysis. But not all the important influencing factors are considered and the deployment rule of the factors has not been established. This paper proposed a probabilistic analysis model of oil pipelines network based on Bayesian network. Most of the important influencing factors, including the key environment condition and emergency response are considered in this model. Moreover, the paper also introduces a deployment rule for these factors. The model can be used in probabilistic analysis and sensitive analysis of oil pipelines network accident.

  5. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 2 2013-01-01 2013-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  6. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 2 2014-01-01 2014-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  7. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 2 2012-01-01 2012-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  8. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  9. 10 CFR 76.85 - Assessment of accidents.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 2 2011-01-01 2011-01-01 false Assessment of accidents. 76.85 Section 76.85 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) CERTIFICATION OF GASEOUS DIFFUSION PLANTS Safety § 76.85 Assessment of accidents. The Corporation shall perform an analysis of potential accidents and consequences to...

  10. Analysis of occupational accidents with biological material among professionals in pre-hospital services.

    PubMed

    de Oliveira, Adriana Cristina; Paiva, Maria Henriqueta Rocha Siqueira

    2013-02-01

    To estimate the prevalence of accidents due to biological material exposure, the characteristics and post-accident conduct among professionals of pre-hospital services of the four municipalities of Minas Gerais, Brazil. A cross-sectional study, using a structured questionnaire that was developed to enable the calculation of prevalence, descriptive analysis and analytical analysis using logistic regression. The study included 228 professionals; the prevalence of accidents due to biological material exposure was 29.4%, with 49.2% percutaneous, 10.4% mucousal, 6.0% non-intact skin, and 34.4% intact skin. Among the professionals injured, those that stood out were nursing technicians (41.9%) and drivers (28.3%). Notification of the occurrence of the accident occurred in 29.8% of the cases. Percutaneous exposure was associated with time of work in the organization (OR=2.51, 95% CI: 1.18 to 5.35, p<0.017). Notification about accidents with biological material should be encouraged, along with professional evaluation/monitoring.

  11. Manned space flight nuclear system safety. Volume 3: Reactor system preliminary nuclear safety analysis. Part 2: Accident Model Document (AMD)

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The Accident Model Document is one of three documents of the Preliminary Safety Analysis Report (PSAR) - Reactor System as applied to a Space Base Program. Potential terrestrial nuclear hazards involving the zirconium hydride reactor-Brayton power module are identified for all phases of the Space Base program. The accidents/events that give rise to the hazards are defined and abort sequence trees are developed to determine the sequence of events leading to the hazard and the associated probabilities of occurence. Source terms are calculated to determine the magnitude of the hazards. The above data is used in the mission accident analysis to determine the most probable and significant accidents/events in each mission phase. The only significant hazards during the prelaunch and launch ascent phases of the mission are those which arise form criticality accidents. Fission product inventories during this time period were found to be very low due to very limited low power acceptance testing.

  12. Single pilot IFR accident data analysis

    NASA Technical Reports Server (NTRS)

    Harris, D. F.; Morrisete, J. A.

    1982-01-01

    The aircraft accident data recorded and maintained by the National Transportation Safety Board for 1964 to 1979 were analyzed to determine what problems exist in the general aviation single pilot instrument flight rules environment. A previous study conducted in 1978 for the years 1964 to 1975 provided a basis for comparison. The purpose was to determine what changes, if any, have occurred in trends and cause-effect relationships reported in the earlier study. The increasing numbers have been tied to measures of activity to produce accident rates which in turn were analyzed in terms of change. Where anomalies or unusually high accident rates were encountered, further analysis was conducted to isolate pertinent patterns of cause factors and/or experience levels of involved pilots. The bulk of the effort addresses accidents in the landing phase of operations. A detailed analysis was performed on controlled/uncontrolled collisions and their unique attributes delineated. Estimates of day vs. night general aviation activity and accident rates were obtained.

  13. Final report on the analyses of traffic accidents : Fast-Trac--phase 3, deliverable. Semi-annual reports on total accidents : trends, types and analysis of before and after studies

    DOT National Transportation Integrated Search

    1996-12-01

    This report contains the results of an analysis of : traffic accidents in the City of Troy, Michigan, where : the Sydney Coordinated Adaptive Traffic System : (SCATS) was deployed as part of a federal demonstration : program. The analyses includes a ...

  14. Causative factors and countermeasures for rural and suburban pedestrian accidents : accident data collection and analysis

    DOT National Transportation Integrated Search

    1977-03-01

    The objectives of the study were to collect and analyze data on rural pedestrian accidents and to identify potential countermeasures. Data on a stratified random sample of over 1,500 rural and suburban accidents from six states was collected during i...

  15. Causative factors and countermeasures for rural and suburban pedestrian accidents : accident data collection and analysis--appendices

    DOT National Transportation Integrated Search

    1977-06-01

    The objectives of the study were to collect and analyze data on rural pedestrian accidents and to identify potential countermeasures. Data on a stratified random sample of over 1,500 rural and suburban accidents from six states was collected during i...

  16. Profile of an Accident Flying Squad

    PubMed Central

    Little, Keith

    1972-01-01

    An analysis of 184 accident flying squad calls and of 280 patients injured in road accidents and treated by a flying squad based on an accident department inclusive from 1967 to 1971 has shown that such a service can provide an efficient system without disrupting the routine work of the hospital. PMID:5076258

  17. Profile of an accident flying squad.

    PubMed

    Little, K

    1972-09-30

    An analysis of 184 accident flying squad calls and of 280 patients injured in road accidents and treated by a flying squad based on an accident department inclusive from 1967 to 1971 has shown that such a service can provide an efficient system without disrupting the routine work of the hospital.

  18. Dynamic analysis of a stochastic rumor propagation model

    NASA Astrophysics Data System (ADS)

    Jia, Fangju; Lv, Guangying

    2018-01-01

    The rapid development of the Internet, especially the emergence of the social networks, leads rumor propagation into a new media era. In this paper, we are concerned with a stochastic rumor propagation model. Sufficient conditions for extinction and persistence in the mean of the rumor are established. The threshold between persistence in the mean and extinction of the rumor is obtained. Compared with the corresponding deterministic model, the threshold affected by the white noise is smaller than the basic reproduction number R0 of the deterministic system.

  19. Northern Hemisphere glaciation and the evolution of Plio-Pleistocene climate noise

    NASA Astrophysics Data System (ADS)

    Meyers, Stephen R.; Hinnov, Linda A.

    2010-08-01

    Deterministic orbital controls on climate variability are commonly inferred to dominate across timescales of 104-106 years, although some studies have suggested that stochastic processes may be of equal or greater importance. Here we explicitly quantify changes in deterministic orbital processes (forcing and/or pacing) versus stochastic climate processes during the Plio-Pleistocene, via time-frequency analysis of two prominent foraminifera oxygen isotopic stacks. Our results indicate that development of the Northern Hemisphere ice sheet is paralleled by an overall amplification of both deterministic and stochastic climate energy, but their relative dominance is variable. The progression from a more stochastic early Pliocene to a strongly deterministic late Pleistocene is primarily accommodated during two transitory phases of Northern Hemisphere ice sheet growth. This long-term trend is punctuated by “stochastic events,” which we interpret as evidence for abrupt reorganization of the climate system at the initiation and termination of the mid-Pleistocene transition and at the onset of Northern Hemisphere glaciation. In addition to highlighting a complex interplay between deterministic and stochastic climate change during the Plio-Pleistocene, our results support an early onset for Northern Hemisphere glaciation (between 3.5 and 3.7 Ma) and reveal some new characteristics of the orbital signal response, such as the puzzling emergence of 100 ka and 400 ka cyclic climate variability during theoretical eccentricity nodes.

  20. Tag-mediated cooperation with non-deterministic genotype-phenotype mapping

    NASA Astrophysics Data System (ADS)

    Zhang, Hong; Chen, Shu

    2016-01-01

    Tag-mediated cooperation provides a helpful framework for resolving evolutionary social dilemmas. However, most of the previous studies have not taken into account genotype-phenotype distinction in tags, which may play an important role in the process of evolution. To take this into consideration, we introduce non-deterministic genotype-phenotype mapping into a tag-based model with spatial prisoner's dilemma. By our definition, the similarity between genotypic tags does not directly imply the similarity between phenotypic tags. We find that the non-deterministic mapping from genotypic tag to phenotypic tag has non-trivial effects on tag-mediated cooperation. Although we observe that high levels of cooperation can be established under a wide variety of conditions especially when the decisiveness is moderate, the uncertainty in the determination of phenotypic tags may have a detrimental effect on the tag mechanism by disturbing the homophilic interaction structure which can explain the promotion of cooperation in tag systems. Furthermore, the non-deterministic mapping may undermine the robustness of the tag mechanism with respect to various factors such as the structure of the tag space and the tag flexibility. This observation warns us about the danger of applying the classical tag-based models to the analysis of empirical phenomena if genotype-phenotype distinction is significant in real world. Non-deterministic genotype-phenotype mapping thus provides a new perspective to the understanding of tag-mediated cooperation.

  1. Manner of Death Determination in Fire Fatalities: 5-Year Autopsy Data of Istanbul City.

    PubMed

    Esen Melez, İpek; Arslan, Murat Nihat; Melez, Deniz Oguzhan; Gürler, Ahmet Selçuk; Büyük, Yalçin

    2017-03-01

    Death resulting from burns is an important social problem and a frequent accident. However, because approximately 10% of cases are estimated to result from a fire that was deliberately started, all fire-related deaths should be treated as suspicious, and the cause of a fire should be investigated. For the bodies recovered from the scene of a fire, the manner of death could also be suicide or homicide. The objective of this study was to contribute to the clarification of controversial data present in the literature on the manner of death determination of fire-related deaths, through evaluation of autopsy findings of bodies recovered from fires. We reviewed 20,135 autopsies performed in a 5-year period, in Istanbul, as the whole autopsy data of the city and found 133 fire-related deaths. The death scene investigation reports and other judicial documents, autopsy findings, and toxicological analysis results were evaluated to determine the parameters of age, sex, level of the burn, vital signs [red flare; soot in the lower respiratory tract, esophagus, and/or stomach; and screening of carboxyhemoglobin (COHb) levels in the blood], toxicological substances, presence of accelerants, cause of death, and manner of death. The manner of death was determined to be an accident in 98 (73.7%) and homicide in 12 (9%) cases, whereas there was no suicide. In addition, it could not be determined in 23 (17.2%) cases. In accidental deaths, the most frequent cause of death was COHb poisoning with statistically significant blood COHb levels greater than 10%. Further, the presence of soot in the lower respiratory tract, esophagus, and/or stomach and the existence of at least 1 or 2 vital signs together were found to be valid deterministic criteria with statistical significance in terms of identifying the manner of death.

  2. Changing contributions of stochastic and deterministic processes in community assembly over a successional gradient.

    PubMed

    Måren, Inger Elisabeth; Kapfer, Jutta; Aarrestad, Per Arild; Grytnes, John-Arvid; Vandvik, Vigdis

    2018-01-01

    Successional dynamics in plant community assembly may result from both deterministic and stochastic ecological processes. The relative importance of different ecological processes is expected to vary over the successional sequence, between different plant functional groups, and with the disturbance levels and land-use management regimes of the successional systems. We evaluate the relative importance of stochastic and deterministic processes in bryophyte and vascular plant community assembly after fire in grazed and ungrazed anthropogenic coastal heathlands in Northern Europe. A replicated series of post-fire successions (n = 12) were initiated under grazed and ungrazed conditions, and vegetation data were recorded in permanent plots over 13 years. We used redundancy analysis (RDA) to test for deterministic successional patterns in species composition repeated across the replicate successional series and analyses of co-occurrence to evaluate to what extent species respond synchronously along the successional gradient. Change in species co-occurrences over succession indicates stochastic successional dynamics at the species level (i.e., species equivalence), whereas constancy in co-occurrence indicates deterministic dynamics (successional niche differentiation). The RDA shows high and deterministic vascular plant community compositional change, especially early in succession. Co-occurrence analyses indicate stochastic species-level dynamics the first two years, which then give way to more deterministic replacements. Grazed and ungrazed successions are similar, but the early stage stochasticity is higher in ungrazed areas. Bryophyte communities in ungrazed successions resemble vascular plant communities. In contrast, bryophytes in grazed successions showed consistently high stochasticity and low determinism in both community composition and species co-occurrence. In conclusion, stochastic and individualistic species responses early in succession give way to more niche-driven dynamics in later successional stages. Grazing reduces predictability in both successional trends and species-level dynamics, especially in plant functional groups that are not well adapted to disturbance. © 2017 The Authors. Ecology, published by Wiley Periodicals, Inc., on behalf of the Ecological Society of America.

  3. Corporate cost of occupational accidents: an activity-based analysis.

    PubMed

    Rikhardsson, Pall M; Impgaard, Martin

    2004-03-01

    The systematic accident cost analysis (SACA) project was carried out during 2001 by The Aarhus School of Business and PricewaterhouseCoopers Denmark with financial support from The Danish National Working Environment Authority. Its focused on developing and testing a method for evaluating occupational costs of companies for use by occupational health and safety professionals. The method was tested in nine Danish companies within three different industry sectors and the costs of 27 selected occupational accidents in these companies were calculated. One of the main conclusions is that the SACA method could be used in all of the companies without revisions. The evaluation of accident cost showed that 2/3 of the costs of occupational accidents are visible in the Danish corporate accounting systems reviewed while 1/3 is hidden from management view. The highest cost of occupational accidents for a company with 3.600 employees was estimated to approximately US$ 682.000. The paper includes an introduction regarding accident cost analysis in companies, a presentation of the SACA project methodology and the SACA method itself, a short overview of some of the results of the SACA project and a conclusion. Further information about the project is available at http://www.asb.dk/saca.

  4. A quarter of a century of the DBQ: some supplementary notes on its validity with regard to accidents.

    PubMed

    de Winter, Joost C F; Dodou, Dimitra; Stanton, Neville A

    2015-01-01

    This article synthesises the latest information on the relationship between the Driver Behaviour Questionnaire (DBQ) and accidents. We show by means of computer simulation that correlations with accidents are necessarily small because accidents are rare events. An updated meta-analysis on the zero-order correlations between the DBQ and self-reported accidents yielded an overall r of .13 (fixed-effect and random-effects models) for violations (57,480 participants; 67 samples) and .09 (fixed-effect and random-effects models) for errors (66,028 participants; 56 samples). An analysis of a previously published DBQ dataset (975 participants) showed that by aggregating across four measurement occasions, the correlation coefficient with self-reported accidents increased from .14 to .24 for violations and from .11 to .19 for errors. Our meta-analysis also showed that DBQ violations (r = .24; 6353 participants; 20 samples) but not DBQ errors (r = - .08; 1086 participants; 16 samples) correlated with recorded vehicle speed. Practitioner Summary: The DBQ is probably the most widely used self-report questionnaire in driver behaviour research. This study shows that DBQ violations and errors correlate moderately with self-reported traffic accidents.

  5. Routes to failure: analysis of 41 civil aviation accidents from the Republic of China using the human factors analysis and classification system.

    PubMed

    Li, Wen-Chin; Harris, Don; Yu, Chung-San

    2008-03-01

    The human factors analysis and classification system (HFACS) is based upon Reason's organizational model of human error. HFACS was developed as an analytical framework for the investigation of the role of human error in aviation accidents, however, there is little empirical work formally describing the relationship between the components in the model. This research analyses 41 civil aviation accidents occurring to aircraft registered in the Republic of China (ROC) between 1999 and 2006 using the HFACS framework. The results show statistically significant relationships between errors at the operational level and organizational inadequacies at both the immediately adjacent level (preconditions for unsafe acts) and higher levels in the organization (unsafe supervision and organizational influences). The pattern of the 'routes to failure' observed in the data from this analysis of civil aircraft accidents show great similarities to that observed in the analysis of military accidents. This research lends further support to Reason's model that suggests that active failures are promoted by latent conditions in the organization. Statistical relationships linking fallible decisions in upper management levels were found to directly affect supervisory practices, thereby creating the psychological preconditions for unsafe acts and hence indirectly impairing the performance of pilots, ultimately leading to accidents.

  6. Statistical Analysis And Treatment Of Accident Black Spots: A Case Study Of Nandyal Mandal

    NASA Astrophysics Data System (ADS)

    Sudharshan Reddy, B.; Vishnu Vardhan Reddy, L.; Sreenivasa Reddy, G., Dr

    2017-08-01

    Background: Increased, economic activity raised the consumption levels of the people across the country. This created scope for increase in travel and transportation. The increase in the vehicles since last 10 years has put lot of pressure on the existing roads and ultimately resulting in road accidents. Nandyal Mandal is located in the Kurnool district of Andhra Pradesh and well developed in both agricultural and industrial sectors after Kurnool. 567 accidents occurred in the last seven years at 143 locations shows the severity of the accidents in the Nandyal Mandal. There is a need to carry out some work in the Nandyal Mandal to improve the accidents black spots for reducing the accidents. Methods: Last seven years (2010-2016) of accident data collected from Police Stations. Weighted Severity Index (WSI), a scientific method is used for identifying the accident black spots. Statistical analysis has carried out for the collected data using Chi-Square Test to determine the independence of accidents with other attributes. Chi-Square Goodness of fit test conducted for test whether the accidents are occurring by chance or following any pattern. Results: WSI values are determined for the 143 locations. The Locations with high WSI are treated as accident black spots. Five black spots are taken for field study. After field observations and interaction with the public, some improvements are suggested for improving the accident black spots. There is no relationship between the severity of accidents and the other attributes like month, season, day, hours in day and the age group except type of vehicle. Road accidents are distributed throughout the Year, Month and Season. Road accidents are not distributed throughout the day.

  7. Historical analysis of US pipeline accidents triggered by natural hazards

    NASA Astrophysics Data System (ADS)

    Girgin, Serkan; Krausmann, Elisabeth

    2015-04-01

    Natural hazards, such as earthquakes, floods, landslides, or lightning, can initiate accidents in oil and gas pipelines with potentially major consequences on the population or the environment due to toxic releases, fires and explosions. Accidents of this type are also referred to as Natech events. Many major accidents highlight the risk associated with natural-hazard impact on pipelines transporting dangerous substances. For instance, in the USA in 1994, flooding of the San Jacinto River caused the rupture of 8 and the undermining of 29 pipelines by the floodwaters. About 5.5 million litres of petroleum and related products were spilled into the river and ignited. As a results, 547 people were injured and significant environmental damage occurred. Post-incident analysis is a valuable tool for better understanding the causes, dynamics and impacts of pipeline Natech accidents in support of future accident prevention and mitigation. Therefore, data on onshore hazardous-liquid pipeline accidents collected by the US Pipeline and Hazardous Materials Safety Administration (PHMSA) was analysed. For this purpose, a database-driven incident data analysis system was developed to aid the rapid review and categorization of PHMSA incident reports. Using an automated data-mining process followed by a peer review of the incident records and supported by natural hazard databases and external information sources, the pipeline Natechs were identified. As a by-product of the data-collection process, the database now includes over 800,000 incidents from all causes in industrial and transportation activities, which are automatically classified in the same way as the PHMSA record. This presentation describes the data collection and reviewing steps conducted during the study, provides information on the developed database and data analysis tools, and reports the findings of a statistical analysis of the identified hazardous liquid pipeline incidents in terms of accident dynamics and consequences.

  8. A methodology for accident analysis of fusion breeder blankets and its application to helium-cooled lead–lithium blanket

    DOE PAGES

    Panayotov, Dobromir; Poitevin, Yves; Grief, Andrew; ...

    2016-09-23

    'Fusion for Energy' (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials,more » and phenomena while remaining consistent with the approach already applied to ITER accident analyses. Furthermore, the methodology phases are illustrated in the paper by its application to the EU HCLL TBS using both MELCOR and RELAP5 codes.« less

  9. Accident Journalism and Traffic Safety Education: A Three-Phase Investigation of Accident Reporting in the Canadian Daily Press.

    ERIC Educational Resources Information Center

    Wilde, Gerald J. S.; Ackersviller, Melody J.

    A study examined the potential for development of a traffic accident-reporting form in the Canadian daily press that strengthens concern for road safety in the general population and enhances knowledge, attitudes, and behavior leading to greater safety. The investigation was conducted on three levels: a content analysis, a readership analysis, and…

  10. Analysis of Sertraline in Postmortem Fluids and Tissues in 11 Aviation Accident Victims

    DTIC Science & Technology

    2012-11-01

    likely undergoes significant postmortem redistribution. 17. Key Words 18. Distribution Statement Forensic Toxicology , Sertraline, Norsertraline... Toxicology .. Forensic Sci Int,.142:.75-100.(2004) . 29 .. Skopp,.G ..Postmortem.Toxicology .. Forensic Sci Med Pathol,.6:.314-25.(2010) . ... toxicological . analysis. on. specimens.from.….aircraft.accident.fatalities”.and.“in- vestigate.….general.aviation.and.air.carrier.accidents. and. search

  11. [Model of Analysis and Prevention of Accidents - MAPA: tool for operational health surveillance].

    PubMed

    de Almeida, Ildeberto Muniz; Vilela, Rodolfo Andrade de Gouveia; da Silva, Alessandro José Nunes; Beltran, Sandra Lorena

    2014-12-01

    The analysis of work-related accidents is important for accident surveillance and prevention. Current methods of analysis seek to overcome reductionist views that see these occurrences as simple events explained by operator error. The objective of this paper is to analyze the Model of Analysis and Prevention of Accidents (MAPA) and its use in monitoring interventions, duly highlighting aspects experienced in the use of the tool. The descriptive analytical method was used, introducing the steps of the model. To illustrate contributions and or difficulties, cases where the tool was used in the context of service were selected. MAPA integrates theoretical approaches that have already been tried in studies of accidents by providing useful conceptual support from the data collection stage until conclusion and intervention stages. Besides revealing weaknesses of the traditional approach, it helps identify organizational determinants, such as management failings, system design and safety management involved in the accident. The main challenges lie in the grasp of concepts by users, in exploring organizational aspects upstream in the chain of decisions or at higher levels of the hierarchy, as well as the intervention to change the determinants of these events.

  12. Rotorcraft Drivetrain Life Safety and Reliability (Cycle de Vie, Securite et Fiabilite des Chaines Dynamiques des Avions a Voilure Tournante)

    DTIC Science & Technology

    1990-06-01

    design and component technologies are reviewed against a background of accident data analysis , resulting in grounds for confidence in higher safety levels...constructors or operators taking voluntary actions based on accident investigations and their own data . Analysis of the CAA Summaty data (Appendix 3...of engines. In the accident data analysis in Appendix 3, insufficient data was available to determine whether rotor configuration or associated

  13. Human factors analysis and classification system applied to civil aircraft accidents in India.

    PubMed

    Gaur, Deepak

    2005-05-01

    The Human Factors Analysis and Classification System (HFACS) has gained wide acceptance as a tool to classify human factors in aircraft accidents and incidents. This study on application of HFACS to civil aircraft accident reports at Directorate General Civil of Aviation (DGCA), India, was conducted to ascertain the practicability of applying HFACS to existing investigation reports and to analyze the trends of human factor causes of civil aircraft accidents. Accident investigation reports held at DGCA, New Delhi, for the period 1990--99 were scrutinized. In all, 83 accidents occurred during this period, of which 48 accident reports were evaluated in this study. One or more human factors contributed to 37 of the 48 (77.1%) accidents. The commonest unsafe act was 'skill based errors' followed by 'decision errors.' Violations of laid down rules were contributory in 16 cases (33.3%). 'Preconditions for unsafe acts' were seen in 23 of the 48 cases (47.9%). A fairly large number (52.1%) had 'organizational influences' contributing to the accident. These results are in consonance with larger studies of accidents in the U.S. Navy and general aviation. Such a high percentage of 'organizational influences' has not been reported in other studies. This is a healthy sign for Indian civil aviation, provided effective remedial action for the same is undertaken.

  14. Analysis of Occupational Accidents in Underground and Surface Mining in Spain Using Data-Mining Techniques

    PubMed Central

    Sanmiquel, Lluís; Bascompta, Marc; Rossell, Josep M.; Anticoi, Hernán Francisco; Guash, Eduard

    2018-01-01

    An analysis of occupational accidents in the mining sector was conducted using the data from the Spanish Ministry of Employment and Social Safety between 2005 and 2015, and data-mining techniques were applied. Data was processed with the software Weka. Two scenarios were chosen from the accidents database: surface and underground mining. The most important variables involved in occupational accidents and their association rules were determined. These rules are composed of several predictor variables that cause accidents, defining its characteristics and context. This study exposes the 20 most important association rules in the sector—either surface or underground mining—based on the statistical confidence levels of each rule as obtained by Weka. The outcomes display the most typical immediate causes, along with the percentage of accidents with a basis in each association rule. The most important immediate cause is body movement with physical effort or overexertion, and the type of accident is physical effort or overexertion. On the other hand, the second most important immediate cause and type of accident are different between the two scenarios. Data-mining techniques were chosen as a useful tool to find out the root cause of the accidents. PMID:29518921

  15. Analysis of Occupational Accidents in Underground and Surface Mining in Spain Using Data-Mining Techniques.

    PubMed

    Sanmiquel, Lluís; Bascompta, Marc; Rossell, Josep M; Anticoi, Hernán Francisco; Guash, Eduard

    2018-03-07

    An analysis of occupational accidents in the mining sector was conducted using the data from the Spanish Ministry of Employment and Social Safety between 2005 and 2015, and data-mining techniques were applied. Data was processed with the software Weka. Two scenarios were chosen from the accidents database: surface and underground mining. The most important variables involved in occupational accidents and their association rules were determined. These rules are composed of several predictor variables that cause accidents, defining its characteristics and context. This study exposes the 20 most important association rules in the sector-either surface or underground mining-based on the statistical confidence levels of each rule as obtained by Weka. The outcomes display the most typical immediate causes, along with the percentage of accidents with a basis in each association rule. The most important immediate cause is body movement with physical effort or overexertion, and the type of accident is physical effort or overexertion. On the other hand, the second most important immediate cause and type of accident are different between the two scenarios. Data-mining techniques were chosen as a useful tool to find out the root cause of the accidents.

  16. Road safety analysis on Achmad Yani frontage road Surabaya

    NASA Astrophysics Data System (ADS)

    Machsus; Prayogo, I.; Chomaedhi; Hayati, D. W.; Utanaka, A.

    2017-11-01

    This research discusses road safety analysis on the operation of frontage road on the west side of Achmad Yani Road Surabaya. This research began by conducting survey on secondary data of traffic accidents. In addition, primary data survey was conducted to obtain traffic data, geometric road data, and other supporting data at the study site along the west side frontage of Ahmad Yani Road Surabaya. Devices used in this research include camera, handy cam, speed gun, counters of vehicles, rolling meter, computer and others. In outline, the stages to conduct this research are divided into 4 stages, namely 1.the preparation stage, 2.data collection and processing, 3. analysis and discussion, and 4. conclusion. The results of this study showed that the accident characteristics of the frontage road are (i) 3 accidents occured per month, (ii) motorcycles was accounted for the largest proportion of accidents which amounted to 74.6 percent, (iii) there were 3 accident victims per month, and (iv) material losses per month worths 1.2 million. The accident rate in 2016 was 0.04 crashes per one million vehicle travels per kilometer, while during 2 months in 2017 it was 0.15 accidents per one million vehicle travels per kilometer. Black spot area of accident is located on Sta 2 + 800 to 2 + 900 which is in front of Graha Pena building and DBL Arena. The high rate of accidents is influenced by the speed of the vehicle which 85 percentile exceeds the speed limit of 40km per hour.

  17. Risk analysis of emergent water pollution accidents based on a Bayesian Network.

    PubMed

    Tang, Caihong; Yi, Yujun; Yang, Zhifeng; Sun, Jie

    2016-01-01

    To guarantee the security of water quality in water transfer channels, especially in open channels, analysis of potential emergent pollution sources in the water transfer process is critical. It is also indispensable for forewarnings and protection from emergent pollution accidents. Bridges above open channels with large amounts of truck traffic are the main locations where emergent accidents could occur. A Bayesian Network model, which consists of six root nodes and three middle layer nodes, was developed in this paper, and was employed to identify the possibility of potential pollution risk. Dianbei Bridge is reviewed as a typical bridge on an open channel of the Middle Route of the South to North Water Transfer Project where emergent traffic accidents could occur. Risk of water pollutions caused by leakage of pollutants into water is focused in this study. The risk for potential traffic accidents at the Dianbei Bridge implies a risk for water pollution in the canal. Based on survey data, statistical analysis, and domain specialist knowledge, a Bayesian Network model was established. The human factor of emergent accidents has been considered in this model. Additionally, this model has been employed to describe the probability of accidents and the risk level. The sensitive reasons for pollution accidents have been deduced. The case has also been simulated that sensitive factors are in a state of most likely to lead to accidents. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Visualization of Traffic Accidents

    NASA Technical Reports Server (NTRS)

    Wang, Jie; Shen, Yuzhong; Khattak, Asad

    2010-01-01

    Traffic accidents have tremendous impact on society. Annually approximately 6.4 million vehicle accidents are reported by police in the US and nearly half of them result in catastrophic injuries. Visualizations of traffic accidents using geographic information systems (GIS) greatly facilitate handling and analysis of traffic accidents in many aspects. Environmental Systems Research Institute (ESRI), Inc. is the world leader in GIS research and development. ArcGIS, a software package developed by ESRI, has the capabilities to display events associated with a road network, such as accident locations, and pavement quality. But when event locations related to a road network are processed, the existing algorithm used by ArcGIS does not utilize all the information related to the routes of the road network and produces erroneous visualization results of event locations. This software bug causes serious problems for applications in which accurate location information is critical for emergency responses, such as traffic accidents. This paper aims to address this problem and proposes an improved method that utilizes all relevant information of traffic accidents, namely, route number, direction, and mile post, and extracts correct event locations for accurate traffic accident visualization and analysis. The proposed method generates a new shape file for traffic accidents and displays them on top of the existing road network in ArcGIS. Visualization of traffic accidents along Hampton Roads Bridge Tunnel is included to demonstrate the effectiveness of the proposed method.

  19. 49 CFR Appendix B to Part 219 - Designation of Laboratory for Post-Accident Toxicological Testing

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Designation of Laboratory for Post-Accident.... 219, App. B Appendix B to Part 219—Designation of Laboratory for Post-Accident Toxicological Testing The following laboratory is currently designated to conduct post-accident toxicological analysis under...

  20. LNG risk management

    NASA Astrophysics Data System (ADS)

    Martino, P.

    1980-12-01

    A general methodology is presented for conducting an analysis of the various aspects of the hazards associated with the storage and transportation of liquefied natural gas (LNG) which should be considered during the planning stages of a typical LNG ship terminal. The procedure includes the performance of a hazards and system analysis of the proposed site, a probability analysis of accident scenarios and safety impacts, an analysis of the consequences of credible accidents such as tanker accidents, spills and fires, the assessment of risks and the design and evaluation of risk mitigation measures.

  1. An Analysis of U.S. Civil Rotorcraft Accidents by Cost and Injury (1990-1996)

    NASA Technical Reports Server (NTRS)

    Iseler, Laura; DeMaio, Joe; Rutkowski, Michael (Technical Monitor)

    2002-01-01

    A study of rotorcraft accidents was conducted to identify safety issues and research areas that might lead to a reduction in rotorcraft accidents and fatalities. The primary source of data was summaries of National Transportation Safety Board (NTSB) accident reports. From 1990 to 1996, the NTSB documented 1396 civil rotorcraft accidents in the United States in which 491 people were killed. The rotorcraft data were compared to airline and general aviation data to determine the relative safety of rotorcraft compared to other segments of the aviation industry. In depth analysis of the rotorcraft data addressed demographics, mission, and operational factors. Rotorcraft were found to have an accident rate about ten times that of commercial airliners and about the same as that of general aviation. The likelihood that an accident would be fatal was about equal for all three classes of operation. The most dramatic division in rotorcraft accidents is between flights flown by private pilots versus professional pilots. Private pilots, flying low cost aircraft in benign environments, have accidents that are due, in large part, to their own errors. Professional pilots, in contrast, are more likely to have accidents that are a result of exacting missions or use of specialized equipment. For both groups judgement error is more likely to lead to a fatal accident than are other types of causes. Several approaches to improving the rotorcraft accident rate are recommended. These mostly address improvement in the training of new pilots and improving the safety awareness of private pilots.

  2. Sensitivity analysis in a Lassa fever deterministic mathematical model

    NASA Astrophysics Data System (ADS)

    Abdullahi, Mohammed Baba; Doko, Umar Chado; Mamuda, Mamman

    2015-05-01

    Lassa virus that causes the Lassa fever is on the list of potential bio-weapons agents. It was recently imported into Germany, the Netherlands, the United Kingdom and the United States as a consequence of the rapid growth of international traffic. A model with five mutually exclusive compartments related to Lassa fever is presented and the basic reproduction number analyzed. A sensitivity analysis of the deterministic model is performed. This is done in order to determine the relative importance of the model parameters to the disease transmission. The result of the sensitivity analysis shows that the most sensitive parameter is the human immigration, followed by human recovery rate, then person to person contact. This suggests that control strategies should target human immigration, effective drugs for treatment and education to reduced person to person contact.

  3. Forecasting transitions in systems with high-dimensional stochastic complex dynamics: a linear stability analysis of the tangled nature model.

    PubMed

    Cairoli, Andrea; Piovani, Duccio; Jensen, Henrik Jeldtoft

    2014-12-31

    We propose a new procedure to monitor and forecast the onset of transitions in high-dimensional complex systems. We describe our procedure by an application to the tangled nature model of evolutionary ecology. The quasistable configurations of the full stochastic dynamics are taken as input for a stability analysis by means of the deterministic mean-field equations. Numerical analysis of the high-dimensional stability matrix allows us to identify unstable directions associated with eigenvalues with a positive real part. The overlap of the instantaneous configuration vector of the full stochastic system with the eigenvectors of the unstable directions of the deterministic mean-field approximation is found to be a good early warning of the transitions occurring intermittently.

  4. Analysis of FARS data on state highways in Oklahoma.

    DOT National Transportation Integrated Search

    2012-11-01

    Analysis of fatality automobile accident data can be challenging in rural areas where a relatively small number of : such accidents occurs on specific sections of highways. Combining crash data for 1998 to 2011 from the Fatality : Analysis Reporting ...

  5. IVHS Countermeasures for Rear-End Collisions, Task 1; Vol. II: Statistical Analysis

    DOT National Transportation Integrated Search

    1994-02-25

    This report is from the NHTSA sponsored program, "IVHS Countermeasures for Rear-End Collisions". This Volume, Volume II, Statistical Analysis, presents the statistical analysis of rear-end collision accident data that characterizes the accidents with...

  6. Soil pH mediates the balance between stochastic and deterministic assembly of bacteria

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tripathi, Binu M.; Stegen, James C.; Kim, Mincheol

    Little is known about the factors affecting the relative influence of stochastic and deterministic processes that governs the assembly of microbial communities in successional soils. Here, we conducted a meta-analysis of bacterial communities using six different successional soils data sets, scattered across different regions, with different pH conditions in early and late successional soils. We found that soil pH was the best predictor of bacterial community assembly and the relative importance of stochastic and deterministic processes along successional soils. Extreme acidic or alkaline pH conditions lead to assembly of phylogenetically more clustered bacterial communities through deterministic processes, whereas pH conditionsmore » close to neutral lead to phylogenetically less clustered bacterial communities with more stochasticity. We suggest that the influence of pH, rather than successional age, is the main driving force in producing trends in phylogenetic assembly of bacteria, and that pH also influences the relative balance of stochastic and deterministic processes along successional soils. Given that pH had a much stronger association with community assembly than did successional age, we evaluated whether the inferred influence of pH was maintained when studying globally-distributed samples collected without regard for successional age. This dataset confirmed the strong influence of pH, suggesting that the influence of soil pH on community assembly processes occurs globally. Extreme pH conditions likely exert more stringent limits on survival and fitness, imposing strong selective pressures through ecological and evolutionary time. Taken together, these findings suggest that the degree to which stochastic vs. deterministic processes shape soil bacterial community assembly is a consequence of soil pH rather than successional age.« less

  7. Deterministic Factors Overwhelm Stochastic Environmental Fluctuations as Drivers of Jellyfish Outbreaks.

    PubMed

    Benedetti-Cecchi, Lisandro; Canepa, Antonio; Fuentes, Veronica; Tamburello, Laura; Purcell, Jennifer E; Piraino, Stefano; Roberts, Jason; Boero, Ferdinando; Halpin, Patrick

    2015-01-01

    Jellyfish outbreaks are increasingly viewed as a deterministic response to escalating levels of environmental degradation and climate extremes. However, a comprehensive understanding of the influence of deterministic drivers and stochastic environmental variations favouring population renewal processes has remained elusive. This study quantifies the deterministic and stochastic components of environmental change that lead to outbreaks of the jellyfish Pelagia noctiluca in the Mediterranen Sea. Using data of jellyfish abundance collected at 241 sites along the Catalan coast from 2007 to 2010 we: (1) tested hypotheses about the influence of time-varying and spatial predictors of jellyfish outbreaks; (2) evaluated the relative importance of stochastic vs. deterministic forcing of outbreaks through the environmental bootstrap method; and (3) quantified return times of extreme events. Outbreaks were common in May and June and less likely in other summer months, which resulted in a negative relationship between outbreaks and SST. Cross- and along-shore advection by geostrophic flow were important concentrating forces of jellyfish, but most outbreaks occurred in the proximity of two canyons in the northern part of the study area. This result supported the recent hypothesis that canyons can funnel P. noctiluca blooms towards shore during upwelling. This can be a general, yet unappreciated mechanism leading to outbreaks of holoplanktonic jellyfish species. The environmental bootstrap indicated that stochastic environmental fluctuations have negligible effects on return times of outbreaks. Our analysis emphasized the importance of deterministic processes leading to jellyfish outbreaks compared to the stochastic component of environmental variation. A better understanding of how environmental drivers affect demographic and population processes in jellyfish species will increase the ability to anticipate jellyfish outbreaks in the future.

  8. Analysis of loss of decay-heat-removal sequences at Browns Ferry Unit One

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Harrington, R.M.

    1983-01-01

    This paper summarizes the Oak Ridge National Laboratory (ORNL) report Loss of DHR Sequences at Browns Ferry Unit One - Accident Sequence Analysis (NUREG/CR-2973). The Loss of DHR investigation is the third in a series of accident studies concerning the BWR 4 - MK I containment plant design. These studies, sponsored by the Nuclear Regulatory Commission Severe Accident Sequence Analysis (SASA) program, have been conducted at ORNL with the full cooperation of the Tennessee Valley Authority (TVA). The purpose of the SASA studies is to predetermine the probable course of postulated severe accidents so as to establish the timing andmore » the sequence of events. The SASA studies also produce recommendations concerning the implementation of better system design and better emergency operating instructions and operator training. The ORNL studies also include a detailed, best-estimate calculation of the release and transport of radioactive fission products following postulated severe accidents.« less

  9. Side differences in cerebrovascular accidents after cardiac surgery: a statistical analysis of neurologic symptoms and possible implications for anatomic mechanisms of aortic particle embolization.

    PubMed

    Boivie, Patrik; Edström, Cecilia; Engström, Karl Gunnar

    2005-03-01

    Aortic manipulation and particle embolization have been identified to cause cerebrovascular accidents in cardiac surgery. Recent data suggest that left-hemispheric cerebrovascular accident (right-sided symptoms) is more common, and this has been interpreted as being caused by aortic cannula stream jets. Our aim was to evaluate symptoms of cerebrovascular accident and side differences from a retrospective statistical analysis. During a 2-year period, 2641 consecutive cardiac surgery cases were analyzed. Patients positive for cerebrovascular accident were extracted from a database designed to monitor clinical symptoms. A protocol was used to confirm symptom data with the correct diagnosis in patient records. Patients were subdivided into 3 groups: control, immediate cerebrovascular accident, and delayed cerebrovascular accident. Among pooled patients, immediate and delayed cerebrovascular accidents were 3.0% and 0.9%, respectively. The expected predisposing factors behind immediate cerebrovascular accidents were significant, although the type of operation affected this search. Aortic quality was a strong predictor ( P < .001). The rate of delayed cerebrovascular accident was unaffected by surgery group. Left-sided symptoms of immediate cerebrovascular accident were approximately twice as frequent ( P = .016) as on the contralateral side. This phenomenon was observed for pooled patients and for isolated coronary bypass procedures (n = 1882; P = .025). Immediate cerebrovascular accident and aortic calcifications are linked. The predominance of left-sided symptoms may suggest that aortic manipulation and anatomic mechanisms in the aortic arch are more likely to cause cerebrovascular accidents than effects from cannula stream jets.

  10. An alternative approach to measure similarity between two deterministic transient signals

    NASA Astrophysics Data System (ADS)

    Shin, Kihong

    2016-06-01

    In many practical engineering applications, it is often required to measure the similarity of two signals to gain insight into the conditions of a system. For example, an application that monitors machinery can regularly measure the signal of the vibration and compare it to a healthy reference signal in order to monitor whether or not any fault symptom is developing. Also in modal analysis, a frequency response function (FRF) from a finite element model (FEM) is often compared with an FRF from experimental modal analysis. Many different similarity measures are applicable in such cases, and correlation-based similarity measures may be most frequently used among these such as in the case where the correlation coefficient in the time domain and the frequency response assurance criterion (FRAC) in the frequency domain are used. Although correlation-based similarity measures may be particularly useful for random signals because they are based on probability and statistics, we frequently deal with signals that are largely deterministic and transient. Thus, it may be useful to develop another similarity measure that takes the characteristics of the deterministic transient signal properly into account. In this paper, an alternative approach to measure the similarity between two deterministic transient signals is proposed. This newly proposed similarity measure is based on the fictitious system frequency response function, and it consists of the magnitude similarity and the shape similarity. Finally, a few examples are presented to demonstrate the use of the proposed similarity measure.

  11. A Random Variable Approach to Nuclear Targeting and Survivability

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Undem, Halvor A.

    We demonstrate a common mathematical formalism for analyzing problems in nuclear survivability and targeting. This formalism, beginning with a random variable approach, can be used to interpret past efforts in nuclear-effects analysis, including targeting analysis. It can also be used to analyze new problems brought about by the post Cold War Era, such as the potential effects of yield degradation in a permanently untested nuclear stockpile. In particular, we illustrate the formalism through four natural case studies or illustrative problems, linking these to actual past data, modeling, and simulation, and suggesting future uses. In the first problem, we illustrate themore » case of a deterministically modeled weapon used against a deterministically responding target. Classic "Cookie Cutter" damage functions result. In the second problem, we illustrate, with actual target test data, the case of a deterministically modeled weapon used against a statistically responding target. This case matches many of the results of current nuclear targeting modeling and simulation tools, including the result of distance damage functions as complementary cumulative lognormal functions in the range variable. In the third problem, we illustrate the case of a statistically behaving weapon used against a deterministically responding target. In particular, we show the dependence of target damage on weapon yield for an untested nuclear stockpile experiencing yield degradation. Finally, and using actual unclassified weapon test data, we illustrate in the fourth problem the case of a statistically behaving weapon used against a statistically responding target.« less

  12. Development of a bespoke human factors taxonomy for gliding accident analysis and its revelations about highly inexperienced UK glider pilots.

    PubMed

    Jarvis, Steve; Harris, Don

    2009-08-01

    Low-hours solo glider pilots have a high risk of accidents compared to more experienced pilots. Numerous taxonomies for causal accident analysis have been produced for powered aviation but none of these is suitable for gliding, so a new taxonomy was required. A human factors taxonomy specifically for glider operations was developed and used to analyse all UK gliding accidents from 2002 to 2006 for their overall causes as well as factors specific to low hours pilots. Fifty-nine categories of pilot-related accident causation emerged, which were formed into progressively larger categories until four overall human factors groups were arrived at: 'judgement'; 'handling'; 'strategy'; 'attention'. 'Handling' accounted for a significantly higher proportion of injuries than other categories. Inexperienced pilots had considerably more accidents in all categories except 'strategy'. Approach control (path judgement, airbrake and speed handling) as well as landing flare misjudgement were chiefly responsible for the high accident rate in early solo glider pilots.

  13. What can the drivers' own description from combined sources provide in an analysis of driver distraction and low vigilance in accident situations?

    PubMed

    Tivesten, Emma; Wiberg, Henrik

    2013-03-01

    Accident data play an important role in vehicle safety development. Accident data sources are generally limited in terms of how much information is provided on driver states and behaviour prior to an accident. However, the precise limitations vary between databases, due to differences in analysis focus and data collection procedures between organisations. If information about a specific accident can be retrieved from more than one data source it should be possible to combine the available information sets to facilitate data from one source to compensate for limitations in the other(s). To investigate the viability of such compensation, this study identified a set of accidents recorded in two different data sources. The first data source investigated was an accident mail survey and the second data source insurance claims documents consisting predominantly of insurance claims completed by the involved road users. An analysis of survey variables was compared to a case analysis including word data derived from the same survey and filed insurance claims documents. For each accident, the added value of having access to more than one source of information was assessed. To limit the scope of this study, three particular topics were investigated: available information on low vigilance (e.g., being drowsy, ill); secondary task distraction (e.g., talking with passengers, mobile phone use); and distraction related to the driving task (e.g., looking for approaching vehicles). Results suggest that for low vigilance and secondary task distraction, a combination of the mail survey and insurance claims documents provide more reliable and detailed pre-crash information than survey variables alone. However, driving related distraction appears to be more difficult to capture. In order to gain a better understanding of the above issues and how frequently they occur in accidents, the data sources and analysis methods suggested here may be combined with other investigation methods such as in-depth accident investigations and pre-crash data recordings. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Coastal flooding as a parameter in multi-criteria analysis for industrial site selection

    NASA Astrophysics Data System (ADS)

    Christina, C.; Memos, C.; Diakoulaki, D.

    2014-12-01

    Natural hazards can trigger major industrial accidents, which apart from affecting industrial installations may cause a series of accidents with serious impacts on human health and the environment far beyond the site boundary. Such accidents, also called Na-Tech (natural - technical) accidents, deserve particular attention since they can cause release of hazardous substances possibly resulting in severe environmental pollution, explosions and/or fires. There are different kinds of natural events or, in general terms, of natural causes of industrial accidents, such as landslides, hurricanes, high winds, tsunamis, lightning, cold/hot temperature, floods, heavy rains etc that have caused accidents. The scope of this paper is to examine the coastal flooding as a parameter in causing an industrial accident, such as the nuclear disaster in Fukushima, Japan, and the critical role of this parameter in industrial site selection. Land use planning is a complex procedure that requires multi-criteria decision analysis involving economic, environmental and social parameters. In this context the parameter of a natural hazard occurrence, such as coastal flooding, for industrial site selection should be set by the decision makers. In this paper it is evaluated the influence that has in the outcome of a multi-criteria decision analysis for industrial spatial planning the parameter of an accident risk triggered by coastal flooding. The latter is analyzed in the context of both sea-and-inland induced flooding.

  15. A risk analysis of winter navigation in Finnish sea areas.

    PubMed

    Valdez Banda, Osiris A; Goerlandt, Floris; Montewka, Jakub; Kujala, Pentti

    2015-06-01

    Winter navigation is a complex but common operation in north-European sea areas. In Finnish waters, the smooth flow of maritime traffic and safety of vessel navigation during the winter period are managed through the Finnish-Swedish winter navigation system (FSWNS). This article focuses on accident risks in winter navigation operations, beginning with a brief outline of the FSWNS. The study analyses a hazard identification model of winter navigation and reviews accident data extracted from four winter periods. These are adopted as a basis for visualizing the risks in winter navigation operations. The results reveal that experts consider ship independent navigation in ice conditions the most complex navigational operation, which is confirmed by accident data analysis showing that the operation constitutes the type of navigation with the highest number of accidents reported. The severity of the accidents during winter navigation is mainly categorized as less serious. Collision is the most typical accident in ice navigation and general cargo the type of vessel most frequently involved in these accidents. Consolidated ice, ice ridges and ice thickness between 15 and 40cm represent the most common ice conditions in which accidents occur. Thus, the analysis presented in this article establishes the key elements for identifying the operation types which would benefit most from further safety engineering and safety or risk management development. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Analysis 320 coal mine accidents using structural equation modeling with unsafe conditions of the rules and regulations as exogenous variables.

    PubMed

    Zhang, Yingyu; Shao, Wei; Zhang, Mengjia; Li, Hejun; Yin, Shijiu; Xu, Yingjun

    2016-07-01

    Mining has been historically considered as a naturally high-risk industry worldwide. Deaths caused by coal mine accidents are more than the sum of all other accidents in China. Statistics of 320 coal mine accidents in Shandong province show that all accidents contain indicators of "unsafe conditions of the rules and regulations" with a frequency of 1590, accounting for 74.3% of the total frequency of 2140. "Unsafe behaviors of the operator" is another important contributory factor, which mainly includes "operator error" and "venturing into dangerous places." A systems analysis approach was applied by using structural equation modeling (SEM) to examine the interactions between the contributory factors of coal mine accidents. The analysis of results leads to three conclusions. (i) "Unsafe conditions of the rules and regulations," affect the "unsafe behaviors of the operator," "unsafe conditions of the equipment," and "unsafe conditions of the environment." (ii) The three influencing factors of coal mine accidents (with the frequency of effect relation in descending order) are "lack of safety education and training," "rules and regulations of safety production responsibility," and "rules and regulations of supervision and inspection." (iii) The three influenced factors (with the frequency in descending order) of coal mine accidents are "venturing into dangerous places," "poor workplace environment," and "operator error." Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. A new approach to modeling aviation accidents

    NASA Astrophysics Data System (ADS)

    Rao, Arjun Harsha

    General Aviation (GA) is a catchall term for all aircraft operations in the US that are not categorized as commercial operations or military flights. GA aircraft account for almost 97% of the US civil aviation fleet. Unfortunately, GA flights have a much higher fatal accident rate than commercial operations. Recent estimates by the Federal Aviation Administration (FAA) showed that the GA fatal accident rate has remained relatively unchanged between 2010 and 2015, with 1566 fatal accidents accounting for 2650 fatalities. Several research efforts have been directed towards betters understanding the causes of GA accidents. Many of these efforts use National Transportation Safety Board (NTSB) accident reports and data. Unfortunately, while these studies easily identify the top types of accidents (e.g., inflight loss of control (LOC)), they usually cannot identify why these accidents are happening. Most NTSB narrative reports for GA accidents are very short (many are only one paragraph long), and do not contain much information on the causes (likely because the causes were not fully identified). NTSB investigators also code each accident using an event-based coding system, which should facilitate identification of patterns and trends in causation, given the high number of GA accidents each year. However, this system is susceptible to investigator interpretation and error, meaning that two investigators may code the same accident differently, or omit applicable codes. To facilitate a potentially better understanding of GA accident causation, this research develops a state-based approach to check for logical gaps or omissions in NTSB accident records, and potentially fills-in the omissions. The state-based approach offers more flexibility as it moves away from the conventional event-based representation of accidents, which classifies events in accidents into several categories such as causes, contributing factors, findings, occurrences, and phase of flight. The method views aviation accidents as a set of hazardous states of a system (pilot and aircraft), and triggers that cause the system to move between hazardous states. I used the NTSB's accident coding manual (that contains nearly 4000 different codes) to develop a "dictionary" of hazardous states, triggers, and information codes. Then, I created the "grammar", or a set of rules, that: (1) orders the hazardous states in each accident; and, (2) links the hazardous states using the appropriate triggers. This approach: (1) provides a more correct count of the causes for accidents in the NTSB database; and, (2) checks for gaps or omissions in NTSB accident data, and fills in some of these gaps using logic-based rules. These rules also help identify and count causes for accidents that were not discernable from previous analyses of historical accident data. I apply the model to 6200 helicopter accidents that occurred in the US between 1982 and 2015. First, I identify the states and triggers that are most likely to be associated with fatal and non-fatal accidents. The results suggest that non-fatal accidents, which account for approximately 84% of the accidents, provide valuable opportunities to learn about the causes for accidents. Next, I investigate the causes of inflight loss of control using both a conventional approach and using the state-based approach. The conventional analysis provides little insight into the causal mechanism for LOC. For instance, the top cause of LOC is "aircraft control/directional control not maintained", which does not provide any insight. In contrast, the state-based analysis showed that pilots' tendency to clip objects frequently triggered LOC (16.7% of LOC accidents)--this finding was not directly discernable from conventional analyses. Finally, I investigate the causes for improper autorotations using both a conventional approach and the state-based approach. The conventional approach uses modifiers (e.g., "improper", "misjudged") associated with "24520: Autorotation" to identify improper autorotations in the pre-2008 system. In the psot-2008 system, the NTSB represents autorotation as a phase of flight, which has no modifier--making it impossible to determine if the autorotation was unsuccessful. In contrast, the state-based analysis identified 632 improper autorotation accidents, compared to 174 with a conventional analysis. Results from the state-based analysis show that not maintaining rotor RPM and improper flare were among the top reasons for improper autorotations. The presence of the "not possible" trigger in 11.6% of improper autorotations, suggests that it was impossible to make an autorotative landing. Improper use of collective is the sixth most frequent trigger for improper autorotation. Correct use of collective pitch control is crucial to maintain rotor RPM during an autorotation (considering that engines are generally not operational during autorotations).

  18. Probabilistic Evaluation of Advanced Ceramic Matrix Composite Structures

    NASA Technical Reports Server (NTRS)

    Abumeri, Galib H.; Chamis, Christos C.

    2003-01-01

    The objective of this report is to summarize the deterministic and probabilistic structural evaluation results of two structures made with advanced ceramic composites (CMC): internally pressurized tube and uniformly loaded flange. The deterministic structural evaluation includes stress, displacement, and buckling analyses. It is carried out using the finite element code MHOST, developed for the 3-D inelastic analysis of structures that are made with advanced materials. The probabilistic evaluation is performed using the integrated probabilistic assessment of composite structures computer code IPACS. The affects of uncertainties in primitive variables related to the material, fabrication process, and loadings on the material property and structural response behavior are quantified. The primitive variables considered are: thermo-mechanical properties of fiber and matrix, fiber and void volume ratios, use temperature, and pressure. The probabilistic structural analysis and probabilistic strength results are used by IPACS to perform reliability and risk evaluation of the two structures. The results will show that the sensitivity information obtained for the two composite structures from the computational simulation can be used to alter the design process to meet desired service requirements. In addition to detailed probabilistic analysis of the two structures, the following were performed specifically on the CMC tube: (1) predicted the failure load and the buckling load, (2) performed coupled non-deterministic multi-disciplinary structural analysis, and (3) demonstrated that probabilistic sensitivities can be used to select a reduced set of design variables for optimization.

  19. Lifestyle and accidents among young drivers.

    PubMed

    Gregersen, N P; Berg, H Y

    1994-06-01

    This study covers the lifestyle component of the problems related to young drivers' accident risk. The purpose of the study is to measure the relationship between lifestyle and accident risk, and to identify specific high-risk and low-risk groups. Lifestyle is measured through a questionnaire, where 20-year-olds describe themselves and how often they deal with a large number of different activities, like sports, music, movies, reading, cars and driving, political engagement, etc. They also report their involvement in traffic accidents. With a principal component analysis followed by a cluster analysis, lifestyle profiles are defined. These profiles are finally correlated to accidents, which makes it possible to define high-risk and low-risk groups. The cluster analysis defined 15 clusters including four high-risk groups with an average overrisk of 150% and two low-risk groups with an average underrisk of 75%. The results are discussed from two perspectives. The first is the importance of theoretical understanding of the contribution of lifestyle factors to young drivers' high accident risk. The second is how the findings could be used in practical road safety measures, like education, campaigns, etc.

  20. Circuit board accident--organizational dimension hidden by prescribed safety.

    PubMed

    de Almeida, Ildeberto Muniz; Buoso, Eduardo; do Amaral Dias, Maria Dionísia; Vilela, Rodolfo Andrade Gouveia

    2012-01-01

    This study analyzes an accident in which two maintenance workers suffered severe burns while replacing a circuit breaker panel in a steel mill, following model of analysis and prevention of accidents (MAPA) developed with the objective of enlarging the perimeter of interventions and contributing to deconstruction of blame attribution practices. The study was based on materials produced by a health service team in an in-depth analysis of the accident. The analysis shows that decisions related to system modernization were taken without considering their implications in maintenance scheduling and creating conflicts of priorities and of interests between production and safety; and also reveals that the lack of a systemic perspective in safety management was its principal failure. To explain the accident as merely non-fulfillment of idealized formal safety rules feeds practices of blame attribution supported by alibi norms and inhibits possible prevention. In contrast, accident analyses undertaken in worker health surveillance services show potential to reveal origins of these events incubated in the history of the system ignored in practices guided by the traditional paradigm.

  1. Potential safety benefits of intelligent cruise control systems.

    PubMed

    Chira-Chavala, T; Yoo, S M

    1994-04-01

    Potential safety impact of a hypothetical intelligent cruise control system (ICCS) is evaluated in terms of changes in traffic accidents and some traffic operation characteristics affecting safety. The analysis of changes in traffic accidents is accomplished by in-depth examinations of police accident reports for four major counties in California. The evaluation of changes in traffic operation characteristics affecting safety is accomplished by vehicle simulation. The accident analysis reveals that the use of the hypothetical ICCS could potentially reduce traffic accidents by up to 7.5%. Preliminary vehicle simulation results based on a 10-vehicle convoy indicate that the use of the hypothetical ICCS could reduce frequencies of hard acceleration and deceleration, enhance speed harmonization among vehicles, and reduce incidence of "less-safe" headway.

  2. Aircraft accidents.method of analysis

    NASA Technical Reports Server (NTRS)

    1937-01-01

    This report is a revision of NACA-TR-357. It was prepared by the Committee on Aircraft Accidents. The purpose of this report is to provide a basis for the classification and comparison of aircraft accidents, both civil and military.

  3. Measuring pedestrian volumes and conflicts. Volume 2, Accident prediction model

    DOT National Transportation Integrated Search

    1987-12-01

    This final report presents the findings, conclusions, and recommendations of the study conducted to model pedestrian/vehicle accidents. A group-type analysis approach for the prediction of pedestrian/vehicle accidents using pedestrian/vehicle conflic...

  4. Risk of Occupational Accidents in Workers with Obstructive Sleep Apnea: Systematic Review and Meta-analysis

    PubMed Central

    Garbarino, Sergio; Guglielmi, Ottavia; Sanna, Antonio; Mancardi, Gian Luigi; Magnavita, Nicola

    2016-01-01

    Study Objectives: Obstructive sleep apnea (OSA) is the single most important preventable medical cause of excessive daytime sleepiness (EDS) and driving accidents. OSA may also adversely affect work performance through a decrease in productivity, and an increase in the injury rate. Nevertheless, no systematic review and meta-analysis of the relationship between OSA and work accidents has been performed thus far. Methods: PubMed, PsycInfo, Scopus, Web of Science, and Cochrane Library were searched. Out of an initial list of 1,099 papers, 10 studies (12,553 participants) were eligible for our review, and 7 of them were included in the meta-analysis. The overall effects were measured by odds ratios (OR) and 95% confidence intervals (CI). An assessment was made of the methodological quality of the studies. Moderator analysis and funnel plot analysis were used to explore the sources of between-study heterogeneity. Results: Compared to controls, the odds of work accident was found to be nearly double in workers with OSA (OR = 2.18; 95% CI = 1.53–3.10). Occupational driving was associated with a higher effect size. Conclusions: OSA is an underdiagnosed nonoccupational disease that has a strong adverse effect on work accidents. The nearly twofold increased odds of work accidents in subjects with OSA calls for workplace screening in selected safety-sensitive occupations. Commentary: A commentary on this article appears in this issue on page 1171. Citation: Garbarino S, Guglielmi O, Sanna A, Mancardi GL, Magnavita N. Risk of occupational accidents in workers with obstructive sleep apnea: systematic review and meta-analysis. SLEEP 2016;39(6):1211–1218. PMID:26951401

  5. Application of 3D documentation and geometric reconstruction methods in traffic accident analysis: with high resolution surface scanning, radiological MSCT/MRI scanning and real data based animation.

    PubMed

    Buck, Ursula; Naether, Silvio; Braun, Marcel; Bolliger, Stephan; Friederich, Hans; Jackowski, Christian; Aghayev, Emin; Christe, Andreas; Vock, Peter; Dirnhofer, Richard; Thali, Michael J

    2007-07-20

    The examination of traffic accidents is daily routine in forensic medicine. An important question in the analysis of the victims of traffic accidents, for example in collisions between motor vehicles and pedestrians or cyclists, is the situation of the impact. Apart from forensic medical examinations (external examination and autopsy), three-dimensional technologies and methods are gaining importance in forensic investigations. Besides the post-mortem multi-slice computed tomography (MSCT) and magnetic resonance imaging (MRI) for the documentation and analysis of internal findings, highly precise 3D surface scanning is employed for the documentation of the external body findings and of injury-inflicting instruments. The correlation of injuries of the body to the injury-inflicting object and the accident mechanism are of great importance. The applied methods include documentation of the external and internal body and the involved vehicles and inflicting tools as well as the analysis of the acquired data. The body surface and the accident vehicles with their damages were digitized by 3D surface scanning. For the internal findings of the body, post-mortem MSCT and MRI were used. The analysis included the processing of the obtained data to 3D models, determination of the driving direction of the vehicle, correlation of injuries to the vehicle damages, geometric determination of the impact situation and evaluation of further findings of the accident. In the following article, the benefits of the 3D documentation and computer-assisted, drawn-to-scale 3D comparisons of the relevant injuries with the damages to the vehicle in the analysis of the course of accidents, especially with regard to the impact situation, are shown on two examined cases.

  6. A Qualitative Study on Organizational Factors Affecting Occupational Accidents

    PubMed Central

    ESKANDARI, Davood; JAFARI, Mohammad Javad; MEHRABI, Yadollah; KIAN, Mostafa Pouya; CHARKHAND, Hossein; MIRGHOTBI, Mostafa

    2017-01-01

    Background: Technical, human, operational and organizational factors have been influencing the sequence of occupational accidents. Among them, organizational factors play a major role in causing occupational accidents. The aim of this research was to understand the Iranian safety experts’ experiences and perception of organizational factors. Methods: This qualitative study was conducted in 2015 by using the content analysis technique. Data were collected through semi-structured interviews with 17 safety experts working in Iranian universities and industries and analyzed with a conventional qualitative content analysis method using the MAXQDA software. Results: Eleven organizational factors’ sub-themes were identified: management commitment, management participation, employee involvement, communication, blame culture, education and training, job satisfaction, interpersonal relationship, supervision, continuous improvement, and reward system. The participants considered these factors as effective on occupational accidents. Conclusion: The mentioned 11 organizational factors are probably involved in occupational accidents in Iran. Naturally, improving organizational factors can increase the safety performance and reduce occupational accidents. PMID:28435824

  7. A Qualitative Study on Organizational Factors Affecting Occupational Accidents.

    PubMed

    Eskandari, Davood; Jafari, Mohammad Javad; Mehrabi, Yadollah; Kian, Mostafa Pouya; Charkhand, Hossein; Mirghotbi, Mostafa

    2017-03-01

    Technical, human, operational and organizational factors have been influencing the sequence of occupational accidents. Among them, organizational factors play a major role in causing occupational accidents. The aim of this research was to understand the Iranian safety experts' experiences and perception of organizational factors. This qualitative study was conducted in 2015 by using the content analysis technique. Data were collected through semi-structured interviews with 17 safety experts working in Iranian universities and industries and analyzed with a conventional qualitative content analysis method using the MAXQDA software. Eleven organizational factors' sub-themes were identified: management commitment, management participation, employee involvement, communication, blame culture, education and training, job satisfaction, interpersonal relationship, supervision, continuous improvement, and reward system. The participants considered these factors as effective on occupational accidents. The mentioned 11 organizational factors are probably involved in occupational accidents in Iran. Naturally, improving organizational factors can increase the safety performance and reduce occupational accidents.

  8. The effects of aircraft certification rules on general aviation accidents

    NASA Astrophysics Data System (ADS)

    Anderson, Carolina Lenz

    The purpose of this study was to analyze the frequency of general aviation airplane accidents and accident rates on the basis of aircraft certification to determine whether or not differences in aircraft certification rules had an influence on accidents. In addition, the narrative cause descriptions contained within the accident reports were analyzed to determine whether there were differences in the qualitative data for the different certification categories. The certification categories examined were: Federal Aviation Regulations Part 23, Civil Air Regulations 3, Light Sport Aircraft, and Experimental-Amateur Built. The accident causes examined were those classified as: Loss of Control, Controlled Flight into Terrain, Engine Failure, and Structural Failure. Airworthiness certification categories represent a wide diversity of government oversight. Part 23 rules have evolved from the initial set of simpler design standards and have progressed into a comprehensive and strict set of rules to address the safety issues of the more complex airplanes within the category. Experimental-Amateur Built airplanes have the least amount of government oversight and are the fastest growing segment. The Light Sport Aircraft category is a more recent certification category that utilizes consensus standards in the approval process. Civil Air Regulations 3 airplanes were designed and manufactured under simpler rules but modifying these airplanes has become lengthy and expensive. The study was conducted using a mixed methods methodology which involves both quantitative and qualitative elements. A Chi-Square test was used for a quantitative analysis of the accident frequency among aircraft certification categories. Accident rate analysis of the accidents among aircraft certification categories involved an ANCOVA test. The qualitative component involved the use of text mining techniques for the analysis of the narrative cause descriptions contained within the accident reports. The Chi-Square test indicated that there was no significant difference in the number of accidents among the different certification categories when either Controlled Flight into Terrain or Structural Failure was listed as cause. However, there was a significant difference in the frequency of accidents with regard to Loss of Control and Engine Failure accidents. The results of the ANCOVA test indicated that there was no significant difference in the accident rate with regard to Loss of Control, Controlled Flight into Terrain, or Structural Failure accidents. There was, however, a significant difference in Engine Failure accidents between Experimental-Amateur Built and the other categories.The text mining analysis of the narrative causes of Loss of Control accidents indicated that only the Civil Air Regulations 3 category airplanes had clusters of words associated with visual flight into instrument meteorological conditions. Civil Air Regulations 3 airplanes were designed and manufactured prior to the 1960s and in most cases have not been retrofitted to take advantage of newer technologies that could help prevent Loss of Control accidents. The study indicated that General Aviation aircraft certification rules do not have a statistically significant effect on aircraft accidents except for Loss of Control and Engine Failure. According to the literature, government oversight could have become an obstacle in the implementation of safety enhancing equipment that could reduce Loss of Control accidents. Oversight should focus on ensuring that Experimental-Amateur Built aircraft owners perform a functional test that could prevent some of the Engine Failure accidents.

  9. Information Services at the Nuclear Safety Analysis Center.

    ERIC Educational Resources Information Center

    Simard, Ronald

    This paper describes the operations of the Nuclear Safety Analysis Center. Established soon after an accident at the Three Mile Island nuclear power plant near Harrisburg, Pennsylvania, its efforts were initially directed towards a detailed analysis of the accident. Continuing functions include: (1) the analysis of generic nuclear safety issues,…

  10. Hybrid deterministic/stochastic simulation of complex biochemical systems.

    PubMed

    Lecca, Paola; Bagagiolo, Fabio; Scarpa, Marina

    2017-11-21

    In a biological cell, cellular functions and the genetic regulatory apparatus are implemented and controlled by complex networks of chemical reactions involving genes, proteins, and enzymes. Accurate computational models are indispensable means for understanding the mechanisms behind the evolution of a complex system, not always explored with wet lab experiments. To serve their purpose, computational models, however, should be able to describe and simulate the complexity of a biological system in many of its aspects. Moreover, it should be implemented by efficient algorithms requiring the shortest possible execution time, to avoid enlarging excessively the time elapsing between data analysis and any subsequent experiment. Besides the features of their topological structure, the complexity of biological networks also refers to their dynamics, that is often non-linear and stiff. The stiffness is due to the presence of molecular species whose abundance fluctuates by many orders of magnitude. A fully stochastic simulation of a stiff system is computationally time-expensive. On the other hand, continuous models are less costly, but they fail to capture the stochastic behaviour of small populations of molecular species. We introduce a new efficient hybrid stochastic-deterministic computational model and the software tool MoBioS (MOlecular Biology Simulator) implementing it. The mathematical model of MoBioS uses continuous differential equations to describe the deterministic reactions and a Gillespie-like algorithm to describe the stochastic ones. Unlike the majority of current hybrid methods, the MoBioS algorithm divides the reactions' set into fast reactions, moderate reactions, and slow reactions and implements a hysteresis switching between the stochastic model and the deterministic model. Fast reactions are approximated as continuous-deterministic processes and modelled by deterministic rate equations. Moderate reactions are those whose reaction waiting time is greater than the fast reaction waiting time but smaller than the slow reaction waiting time. A moderate reaction is approximated as a stochastic (deterministic) process if it was classified as a stochastic (deterministic) process at the time at which it crosses the threshold of low (high) waiting time. A Gillespie First Reaction Method is implemented to select and execute the slow reactions. The performances of MoBios were tested on a typical example of hybrid dynamics: that is the DNA transcription regulation. The simulated dynamic profile of the reagents' abundance and the estimate of the error introduced by the fully deterministic approach were used to evaluate the consistency of the computational model and that of the software tool.

  11. Bayesian-network-based safety risk assessment for steel construction projects.

    PubMed

    Leu, Sou-Sen; Chang, Ching-Miao

    2013-05-01

    There are four primary accident types at steel building construction (SC) projects: falls (tumbles), object falls, object collapse, and electrocution. Several systematic safety risk assessment approaches, such as fault tree analysis (FTA) and failure mode and effect criticality analysis (FMECA), have been used to evaluate safety risks at SC projects. However, these traditional methods ineffectively address dependencies among safety factors at various levels that fail to provide early warnings to prevent occupational accidents. To overcome the limitations of traditional approaches, this study addresses the development of a safety risk-assessment model for SC projects by establishing the Bayesian networks (BN) based on fault tree (FT) transformation. The BN-based safety risk-assessment model was validated against the safety inspection records of six SC building projects and nine projects in which site accidents occurred. The ranks of posterior probabilities from the BN model were highly consistent with the accidents that occurred at each project site. The model accurately provides site safety-management abilities by calculating the probabilities of safety risks and further analyzing the causes of accidents based on their relationships in BNs. In practice, based on the analysis of accident risks and significant safety factors, proper preventive safety management strategies can be established to reduce the occurrence of accidents on SC sites. Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. Accidents in Germany: evaluation of the german telephone health survey 2004.

    PubMed

    Saß, Anke-Christine

    2008-09-01

    In the year 2006 there were over 19 000 fatal accidents in Germany and estimates put the number of accidental injuries at more than 8 million. Detailed information on the pattern of accidents is indispensable for the definition of priorities in accident prevention. The German Telephone Health Survey 2004 provides representative cross-sectional data on the health of German residents from 18 years of age (n = 7341). Questions on the prevalence of accidents (13 items) were selected for analysis. Every tenth interviewee reported being injured in an accident in the previous 12 months. Men, particularly young men, are at greater risk of accidents than women. Almost one third of all accidents occurred at home. Social status had no influence on the probability of having an accident, but did affect where the accident happened. The survey yields information on the overall pattern of non-fatal accidents in Germany. The data point to target groups for accident prevention measures.

  13. [An analysis of industrial accidents in the working field with a particular emphasis on repeated accidents].

    PubMed

    Wakisaka, I; Yanagihashi, T; Tomari, T; Sato, M

    1990-03-01

    The present study is based on an analysis of routinely submitted reports of occupational accidents experienced by the workers of industrial enterprises under the jurisdiction of Kagoshima Labor Standard Office during a 5-year period 1983 to 1987. Officially notified injuries serious enough to keep employees away from their job for work at least 4 days were utilized in this study. Data was classified so as to give an observed frequency distribution for workers having any specified number of accidents. Also, the accident rate which is an indicator of the risk of accident was compared among different occupations, between age groups and between the sexes. Results obtained are as follows; 1) For the combined total of 6,324 accident cases for 8 types of occupation (Construction, Transportation, Mining & Quarrying, Forestry, Food manufacture, Lumber & Woodcraft, Manufacturing industry and Other business), the number of those who had at least one accident was 6,098, of which 5,837 were injured only once, 208 twice, 21 three times and 2 four times. When occupation type was fixed, however, the number of workers having one, two, three and four times of accidents were 5,895, 182, 19 and 2, respectively. This suggests that some workers are likely to have experienced repeated accidents in more than one type of occupation.(ABSTRACT TRUNCATED AT 250 WORDS)

  14. Probabilistic versus deterministic hazard assessment in liquefaction susceptible zones

    NASA Astrophysics Data System (ADS)

    Daminelli, Rosastella; Gerosa, Daniele; Marcellini, Alberto; Tento, Alberto

    2015-04-01

    Probabilistic seismic hazard assessment (PSHA), usually adopted in the framework of seismic codes redaction, is based on Poissonian description of the temporal occurrence, negative exponential distribution of magnitude and attenuation relationship with log-normal distribution of PGA or response spectrum. The main positive aspect of this approach stems into the fact that is presently a standard for the majority of countries, but there are weak points in particular regarding the physical description of the earthquake phenomenon. Factors like site effects, source characteristics like duration of the strong motion and directivity that could significantly influence the expected motion at the site are not taken into account by PSHA. Deterministic models can better evaluate the ground motion at a site from a physical point of view, but its prediction reliability depends on the degree of knowledge of the source, wave propagation and soil parameters. We compare these two approaches in selected sites affected by the May 2012 Emilia-Romagna and Lombardia earthquake, that caused widespread liquefaction phenomena unusually for magnitude less than 6. We focus on sites liquefiable because of their soil mechanical parameters and water table level. Our analysis shows that the choice between deterministic and probabilistic hazard analysis is strongly dependent on site conditions. The looser the soil and the higher the liquefaction potential, the more suitable is the deterministic approach. Source characteristics, in particular the duration of strong ground motion, have long since recognized as relevant to induce liquefaction; unfortunately a quantitative prediction of these parameters appears very unlikely, dramatically reducing the possibility of their adoption in hazard assessment. Last but not least, the economic factors are relevant in the choice of the approach. The case history of 2012 Emilia-Romagna and Lombardia earthquake, with an officially estimated cost of 6 billions Euros, shows that geological and geophysical investigations necessary to assess a reliable deterministic hazard evaluation are largely justified.

  15. Human factors analysis and classification system-HFACS.

    DOT National Transportation Integrated Search

    2000-02-01

    Human error has been implicated in 70 to 80% of all civil and military aviation accidents. Yet, most accident : reporting systems are not designed around any theoretical framework of human error. As a result, most : accident databases are not conduci...

  16. Development of a bespoke human factors taxonomy for gliding accident analysis and its revelations about highly inexperienced UK glider pilots.

    PubMed

    Jarvis, Steve; Harris, Don

    2010-02-01

    Low-hours solo glider pilots have a high risk of accidents compared to more experienced pilots. Numerous taxonomies for causal accident analysis have been produced for powered aviation but none of these is suitable for gliding, so a new taxonomy was required. A human factors taxonomy specifically for glider operations was developed and used to analyse all UK gliding accidents from 2002 to 2006 for their overall causes as well as factors specific to low hours pilots. Fifty-nine categories of pilot-related accident causation emerged, which were formed into progressively larger categories until four overall human factors groups were arrived at: 'judgement'; 'handling'; 'strategy'; 'attention'. 'Handling' accounted for a significantly higher proportion of injuries than other categories. Inexperienced pilots had considerably more accidents in all categories except 'strategy'. Approach control (path judgement, airbrake and speed handling) as well as landing flare misjudgement were chiefly responsible for the high accident rate in early solo glider pilots. Statement of Relevance: This paper uses extant accident data to produce a taxonomy of underlying human factors causes to analyse gliding accidents and identify the specific causes associated with low hours pilots. From this specific, well-targeted remedial measures can be identified.

  17. Scenario analysis of freight vehicle accident risks in Taiwan.

    PubMed

    Tsai, Ming-Chih; Su, Chien-Chih

    2004-07-01

    This study develops a quantitative risk model by utilizing Generalized Linear Interactive Model (GLIM) to analyze the major freight vehicle accidents in Taiwan. Eight scenarios are established by interacting three categorical variables of driver ages, vehicle types and road types, each of which contains two levels. The database that consists of 2043 major accidents occurring between 1994 and 1998 in Taiwan is utilized to fit and calibrate the model parameters. The empirical results indicate that accident rates of freight vehicles in Taiwan were high in the scenarios involving trucks and non-freeway systems, while; accident consequences were severe in the scenarios involving mature drivers or non-freeway systems. Empirical evidences also show that there is no significant relationship between accident rates and accident consequences. This is to stress that safety studies that describe risk merely as accident rates rather than the combination of accident rates and consequences by definition might lead to biased risk perceptions. Finally, the study recommends using number of vehicle as an alternative of traffic exposure in commercial vehicle risk analysis. The merits of this would be that it is simple and thus reliable; meanwhile, the resulted risk that is termed as fatalities per vehicle could provide clear and direct policy implications for insurance practices and safety regulations.

  18. An Analysis of Coherent Digital Receivers in the Presence of Colored Noise Interference.

    DTIC Science & Technology

    1985-06-01

    115 6.4 Pe for Det-erministic Jamnmers, JSR = 0.01, E0.3---------------------------------------------116 6.5 Pe for Deterministic Jamnmers, JSR = 0.1...k k where h p(t) and hhi(t) are the particular and homogeneous solutions, respectively, to a differential equation derived from the Fredholm I...yields 2 2D(s2)c (s) = N(s ) (3.4)c Multiplication by s corresponds to differentiation with respect to t in the time domain. So, Eq. (3.4) becomes D(p 2)K

  19. Quantitative analysis of random ameboid motion

    NASA Astrophysics Data System (ADS)

    Bödeker, H. U.; Beta, C.; Frank, T. D.; Bodenschatz, E.

    2010-04-01

    We quantify random migration of the social ameba Dictyostelium discoideum. We demonstrate that the statistics of cell motion can be described by an underlying Langevin-type stochastic differential equation. An analytic expression for the velocity distribution function is derived. The separation into deterministic and stochastic parts of the movement shows that the cells undergo a damped motion with multiplicative noise. Both contributions to the dynamics display a distinct response to external physiological stimuli. The deterministic component depends on the developmental state and ambient levels of signaling substances, while the stochastic part does not.

  20. Incorporating real-time traffic and weather data to explore road accident likelihood and severity in urban arterials.

    PubMed

    Theofilatos, Athanasios

    2017-06-01

    The effective treatment of road accidents and thus the enhancement of road safety is a major concern to societies due to the losses in human lives and the economic and social costs. The investigation of road accident likelihood and severity by utilizing real-time traffic and weather data has recently received significant attention by researchers. However, collected data mainly stem from freeways and expressways. Consequently, the aim of the present paper is to add to the current knowledge by investigating accident likelihood and severity by exploiting real-time traffic and weather data collected from urban arterials in Athens, Greece. Random Forests (RF) are firstly applied for preliminary analysis purposes. More specifically, it is aimed to rank candidate variables according to their relevant importance and provide a first insight on the potential significant variables. Then, Bayesian logistic regression as well finite mixture and mixed effects logit models are applied to further explore factors associated with accident likelihood and severity respectively. Regarding accident likelihood, the Bayesian logistic regression showed that variations in traffic significantly influence accident occurrence. On the other hand, accident severity analysis revealed a generally mixed influence of traffic variations on accident severity, although international literature states that traffic variations increase severity. Lastly, weather parameters did not find to have a direct influence on accident likelihood or severity. The study added to the current knowledge by incorporating real-time traffic and weather data from urban arterials to investigate accident occurrence and accident severity mechanisms. The identification of risk factors can lead to the development of effective traffic management strategies to reduce accident occurrence and severity of injuries in urban arterials. Copyright © 2017 Elsevier Ltd and National Safety Council. All rights reserved.

  1. National and regional analysis of road accidents in Spain.

    PubMed

    Tolón-Becerra, A; Lastra-Bravo, X; Flores-Parra, I

    2013-01-01

    In Spain, the absolute fatality figures decreased almost 50 percent between 1998 and 2009. Despite this great effort, road mortality is still of great concern to political authorities. Further progress requires efficient road safety policy based on an optimal set of measures and targets that consider the initial conditions and characteristics in each region. This study attempts to analyze road accidents in Spain and its provinces in time and space during 1998-2009. First, we analyzed daily, monthly, and nationwide (NUTS 0) development of road accidents, the correlation between logarithmic transformations of road accidents and territorial and socioeconomic variables, the causality by simple linear regression of road accidents and territorial and socioeconomic variables, and preliminary frequency by fast Fourier transform. Then we analyzed the annual trend in accidents in the Spanish provinces (NUTS 3) and found a correlation between the logarithmic transformations of the mortality rate, fatalities per fatal accident, and accidents resulting in injuries per inhabitant variables and population, population density, gross domestic product (GDP), length of road network, and area. Finally, causality was analyzed by simple linear regression. The most outstanding results were the negative correlation between mortality rate and population density in Spanish provinces, which has increased over time, and that road accidents in Spain have an approximate periodicity of 57 days. The fast Fourier transform analysis of road accident frequency in Spain was useful in identifying the periodic, harmonic components of accidents and casualties. The periodicity observed both for the period 1998-2009 and by year showed that the highest intensity in road accidents was bimonthly, despite the lower number of accidents and casualties in the spectra of amplitude and power and efforts to reduce the intensity and concentration during off-season travel (summer and December).

  2. USING A RISK-BASED METHODOLOGY FOR THE TRANSFER OF RADIOACTIVE MATERIAL WITHIN THE SAVANNAH RIVER SITE BOUNDARY

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Loftin, B; Watkins, R; Loibl, M

    2010-06-03

    Shipment of radioactive materials (RAM) is discussed in the Code of Federal Regulations in parts of both 49 CFR and 10 CFR. The regulations provide the requirements and rules necessary for the safe shipment of RAM across public highways, railways, waterways, and through the air. These shipments are sometimes referred to as in-commerce shipments. Shipments of RAM entirely within the boundaries of Department of Energy sites, such as the Savannah River Site (SRS), can be made using methodology allowing provisions to maintain equivalent safety while deviating from the regulations for in-commerce shipments. These onsite shipments are known as transfers atmore » the SRS. These transfers must follow the requirements approved in a site-specific Transportation Safety Document (TSD). The TSD defines how the site will transfer materials so that they have equivalence to the regulations. These equivalences are documented in an Onsite Safety Assessment (OSA). The OSA can show how a particular packaging used onsite is equivalent to that which would be used for an in-commerce shipment. This is known as a deterministic approach. However, when a deterministic approach is not viable, the TSD allows for a risk-based OSA to be written. These risk-based assessments show that if a packaging does not provide the necessary safety to ensure that materials are not released (during normal or accident conditions) then the worst-case release of materials does not result in a dose consequence worse than that defined for the SRS. This paper will discuss recent challenges and successes using this methodology at the SRS.« less

  3. Langevin approach to a chemical wave front: Selection of the propagation velocity in the presence of internal noise

    NASA Astrophysics Data System (ADS)

    Lemarchand, A.; Lesne, A.; Mareschal, M.

    1995-05-01

    The reaction-diffusion equation associated with the Fisher chemical model A+B-->2A admits wave-front solutions by replacing an unstable stationary state with a stable one. The deterministic analysis concludes that their propagation velocity is not prescribed by the dynamics. For a large class of initial conditions the velocity which is spontaneously selected is equal to the minimum allowed velocity vmin, as predicted by the marginal stability criterion. In order to test the relevance of this deterministic description we investigate the macroscopic consequences, on the velocity and the width of the front, of the intrinsic stochasticity due to the underlying microscopic dynamics. We solve numerically the Langevin equations, deduced analytically from the master equation within a system size expansion procedure. We show that the mean profile associated with the stochastic solution propagates faster than the deterministic solution at a velocity up to 25% greater than vmin.

  4. A Content Analysis of News Media Coverage of the Accident at Three Mile Island.

    ERIC Educational Resources Information Center

    Stephens, Mitchell; Edison, Nadyne G.

    A study was conducted for the President's Commission on the Accident at Three Mile Island to analyze coverage of the accident by ten news organizations: two wire services, three commercial television networks, and five daily newspapers. Copies of all stories and transcripts of news programs during the first week of the accident were examined from…

  5. Is "Safety-in-numbers" theory applies to the pattern of pedestrian accidents in Seoul, South Korea.

    NASA Astrophysics Data System (ADS)

    Choi, Y.; Yoon, H.

    2016-12-01

    Every year, about 1.25 million people die of vehicle-related accidents, among which half are pedestrians with higher vulnerability: pedestrian, cyclists and motorcyclist (World Health Organization, 2016). This urges city governments in the world to strive for pedestrian safety and to apply diverse theories to transportation planning and design. The common belief is that the number of pedestrian accidents is directly and positively associated with the volume of pedestrian, however, another hypothesis, called "safety-in-numbers" effect, tells an opposite story in that accident rates declines with increase of the volume of pedestrian. In this study, we examine first, whether the safety-in-numbers theory applies to the pattern of pedestrian accidents in Seoul, and second, further investigate environmental factors that are associated with the pedestrian safety. On the first count, we use geospatial statistical analyses of the multi-year pedestrian accident data collected by Korea Road Traffic Authority (KoRoad) and the pedestrian volume data collected by SK Telecom (SKT). With Kernel Density Estimation and Bivariate Local Moran's I, we identify spatial clustering of pedestrian accidents in the city, and examine whether those locations match with concentrations of pedestrian volume. On the second count, we use statistical analysis, tobit, poisson and negative binomial regression to investigate relationships between pedestrian volume and number of pedestrian accident for the two types of geographic areas by the results of the aforementioned analysis; Area 1- locations of high volume of pedestrian with high number of accident, Area 2- locations of high volume of pedestrian with low number of accident. For environmental factors potentially explaining pedestrian accidents, we include land use composition, number of traffic lanes, crosswalk presence, pedestrian signal, traffic island and sidewalk width in our analysis. This research will be valuable in city governments' decision making with planning guidelines and political protocols for making safer pedestrian environment.

  6. Bus accident analysis of routes with/without bus priority.

    PubMed

    Goh, Kelvin Chun Keong; Currie, Graham; Sarvi, Majid; Logan, David

    2014-04-01

    This paper summarises findings on road safety performance and bus-involved accidents in Melbourne along roads where bus priority measures had been applied. Results from an empirical analysis of the accident types revealed significant reduction in the proportion of accidents involving buses hitting stationary objects and vehicles, which suggests the effect of bus priority in addressing manoeuvrability issues for buses. A mixed-effects negative binomial (MENB) regression and back-propagation neural network (BPNN) modelling of bus accidents considering wider influences on accident rates at a route section level also revealed significant safety benefits when bus priority is provided. Sensitivity analyses done on the BPNN model showed general agreement in the predicted accident frequency between both models. The slightly better performance recorded by the MENB model results suggests merits in adopting a mixed effects modelling approach for accident count prediction in practice given its capability to account for unobserved location and time-specific factors. A major implication of this research is that bus priority in Melbourne's context acts to improve road safety and should be a major consideration for road management agencies when implementing bus priority and road schemes. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Transmutation approximations for the application of hybrid Monte Carlo/deterministic neutron transport to shutdown dose rate analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Biondo, Elliott D.; Wilson, Paul P. H.

    In fusion energy systems (FES) neutrons born from burning plasma activate system components. The photon dose rate after shutdown from resulting radionuclides must be quantified. This shutdown dose rate (SDR) is calculated by coupling neutron transport, activation analysis, and photon transport. The size, complexity, and attenuating configuration of FES motivate the use of hybrid Monte Carlo (MC)/deterministic neutron transport. The Multi-Step Consistent Adjoint Driven Importance Sampling (MS-CADIS) method can be used to optimize MC neutron transport for coupled multiphysics problems, including SDR analysis, using deterministic estimates of adjoint flux distributions. When used for SDR analysis, MS-CADIS requires the formulation ofmore » an adjoint neutron source that approximates the transmutation process. In this work, transmutation approximations are used to derive a solution for this adjoint neutron source. It is shown that these approximations are reasonably met for typical FES neutron spectra and materials over a range of irradiation scenarios. When these approximations are met, the Groupwise Transmutation (GT)-CADIS method, proposed here, can be used effectively. GT-CADIS is an implementation of the MS-CADIS method for SDR analysis that uses a series of single-energy-group irradiations to calculate the adjoint neutron source. For a simple SDR problem, GT-CADIS provides speedups of 200 100 relative to global variance reduction with the Forward-Weighted (FW)-CADIS method and 9 ± 5 • 104 relative to analog. As a result, this work shows that GT-CADIS is broadly applicable to FES problems and will significantly reduce the computational resources necessary for SDR analysis.« less

  8. Transmutation approximations for the application of hybrid Monte Carlo/deterministic neutron transport to shutdown dose rate analysis

    DOE PAGES

    Biondo, Elliott D.; Wilson, Paul P. H.

    2017-05-08

    In fusion energy systems (FES) neutrons born from burning plasma activate system components. The photon dose rate after shutdown from resulting radionuclides must be quantified. This shutdown dose rate (SDR) is calculated by coupling neutron transport, activation analysis, and photon transport. The size, complexity, and attenuating configuration of FES motivate the use of hybrid Monte Carlo (MC)/deterministic neutron transport. The Multi-Step Consistent Adjoint Driven Importance Sampling (MS-CADIS) method can be used to optimize MC neutron transport for coupled multiphysics problems, including SDR analysis, using deterministic estimates of adjoint flux distributions. When used for SDR analysis, MS-CADIS requires the formulation ofmore » an adjoint neutron source that approximates the transmutation process. In this work, transmutation approximations are used to derive a solution for this adjoint neutron source. It is shown that these approximations are reasonably met for typical FES neutron spectra and materials over a range of irradiation scenarios. When these approximations are met, the Groupwise Transmutation (GT)-CADIS method, proposed here, can be used effectively. GT-CADIS is an implementation of the MS-CADIS method for SDR analysis that uses a series of single-energy-group irradiations to calculate the adjoint neutron source. For a simple SDR problem, GT-CADIS provides speedups of 200 100 relative to global variance reduction with the Forward-Weighted (FW)-CADIS method and 9 ± 5 • 104 relative to analog. As a result, this work shows that GT-CADIS is broadly applicable to FES problems and will significantly reduce the computational resources necessary for SDR analysis.« less

  9. 1997 Oregon state highway accident rate tables

    DOT National Transportation Integrated Search

    1998-08-01

    The three parts of this report are: : I Results of Analysis containing comparative tables and the Signed Route on Highway list, : II Five year accident rate data by highway sections, : III A summary of this year's fatal traffic accidents. : The first...

  10. Modeling traffic accidents at signalized intersections in the city of Norfolk, VA.

    DOT National Transportation Integrated Search

    2010-12-31

    This study was an attempt to apply a proactive approach using traffic pattern and signalized intersection characteristics to predict accident rates at signalized intersections in a citys arterial network. An earlier analysis of accident data at se...

  11. Seismic Hazard Analysis — Quo vadis?

    NASA Astrophysics Data System (ADS)

    Klügel, Jens-Uwe

    2008-05-01

    The paper is dedicated to the review of methods of seismic hazard analysis currently in use, analyzing the strengths and weaknesses of different approaches. The review is performed from the perspective of a user of the results of seismic hazard analysis for different applications such as the design of critical and general (non-critical) civil infrastructures, technical and financial risk analysis. A set of criteria is developed for and applied to an objective assessment of the capabilities of different analysis methods. It is demonstrated that traditional probabilistic seismic hazard analysis (PSHA) methods have significant deficiencies, thus limiting their practical applications. These deficiencies have their roots in the use of inadequate probabilistic models and insufficient understanding of modern concepts of risk analysis, as have been revealed in some recent large scale studies. These deficiencies result in the lack of ability of a correct treatment of dependencies between physical parameters and finally, in an incorrect treatment of uncertainties. As a consequence, results of PSHA studies have been found to be unrealistic in comparison with empirical information from the real world. The attempt to compensate these problems by a systematic use of expert elicitation has, so far, not resulted in any improvement of the situation. It is also shown that scenario-earthquakes developed by disaggregation from the results of a traditional PSHA may not be conservative with respect to energy conservation and should not be used for the design of critical infrastructures without validation. Because the assessment of technical as well as of financial risks associated with potential damages of earthquakes need a risk analysis, current method is based on a probabilistic approach with its unsolved deficiencies. Traditional deterministic or scenario-based seismic hazard analysis methods provide a reliable and in general robust design basis for applications such as the design of critical infrastructures, especially with systematic sensitivity analyses based on validated phenomenological models. Deterministic seismic hazard analysis incorporates uncertainties in the safety factors. These factors are derived from experience as well as from expert judgment. Deterministic methods associated with high safety factors may lead to too conservative results, especially if applied for generally short-lived civil structures. Scenarios used in deterministic seismic hazard analysis have a clear physical basis. They are related to seismic sources discovered by geological, geomorphologic, geodetic and seismological investigations or derived from historical references. Scenario-based methods can be expanded for risk analysis applications with an extended data analysis providing the frequency of seismic events. Such an extension provides a better informed risk model that is suitable for risk-informed decision making.

  12. Analysis of Child-related Road Traffic Accidents in Vietnam

    NASA Astrophysics Data System (ADS)

    Vu, Anh Tuan; Nguyen, Dinh Vinh Man

    2018-04-01

    In recent years, the number of road traffic accidents, fatalities and injuries have been decreasing, but the figures of children road traffic accidents have been increasing in Ho Chi Minh City of Vietnam. This fact strongly calls for implementing effective solutions to improve traffic safety for children by the local government. This paper presents the trends, patterns and causes of road traffic accidents involving children based on the analysis of road traffic accident data over the period 2010-2015 and the video-based observations of road traffic law violations at 15 typical school gates and 10 typical roads. The results could be useful for the city government to formulate solutions to effectively improve traffic safety for children in Ho Chi Minh City and other cities in Vietnam.

  13. Reliability verification of vehicle speed estimate method in forensic videos.

    PubMed

    Kim, Jong-Hyuk; Oh, Won-Taek; Choi, Ji-Hun; Park, Jong-Chan

    2018-06-01

    In various types of traffic accidents, including car-to-car crash, vehicle-pedestrian collision, and hit-and-run accident, driver overspeed is one of the critical issues of traffic accident analysis. Hence, analysis of vehicle speed at the moment of accident is necessary. The present article proposes a vehicle speed estimate method (VSEM) applying a virtual plane and a virtual reference line to a forensic video. The reliability of the VSEM was verified by comparing the results obtained by applying the VSEM to videos from a test vehicle driving with a global positioning system (GPS)-based Vbox speed. The VSEM verified by these procedures was applied to real traffic accident examples to evaluate the usability of the VSEM. Copyright © 2018 Elsevier B.V. All rights reserved.

  14. Explorative spatial analysis of traffic accident statistics and road mortality among the provinces of Turkey.

    PubMed

    Erdogan, Saffet

    2009-10-01

    The aim of the study is to describe the inter-province differences in traffic accidents and mortality on roads of Turkey. Two different risk indicators were used to evaluate the road safety performance of the provinces in Turkey. These indicators are the ratios between the number of persons killed in road traffic accidents (1) and the number of accidents (2) (nominators) and their exposure to traffic risk (denominator). Population and the number of registered motor vehicles in the provinces were used as denominators individually. Spatial analyses were performed to the mean annual rate of deaths and to the number of fatal accidents that were calculated for the period of 2001-2006. Empirical Bayes smoothing was used to remove background noise from the raw death and accident rates because of the sparsely populated provinces and small number of accident and death rates of provinces. Global and local spatial autocorrelation analyses were performed to show whether the provinces with high rates of deaths-accidents show clustering or are located closer by chance. The spatial distribution of provinces with high rates of deaths and accidents was nonrandom and detected as clustered with significance of P<0.05 with spatial autocorrelation analyses. Regions with high concentration of fatal accidents and deaths were located in the provinces that contain the roads connecting the Istanbul, Ankara, and Antalya provinces. Accident and death rates were also modeled with some independent variables such as number of motor vehicles, length of roads, and so forth using geographically weighted regression analysis with forward step-wise elimination. The level of statistical significance was taken as P<0.05. Large differences were found between the rates of deaths and accidents according to denominators in the provinces. The geographically weighted regression analyses did significantly better predictions for both accident rates and death rates than did ordinary least regressions, as indicated by adjusted R(2) values. Geographically weighted regression provided values of 0.89-0.99 adjusted R(2) for death and accident rates, compared with 0.88-0.95, respectively, by ordinary least regressions. Geographically weighted regression has the potential to reveal local patterns in the spatial distribution of rates, which would be ignored by the ordinary least regression approach. The application of spatial analysis and modeling of accident statistics and death rates at provincial level in Turkey will help to identification of provinces with outstandingly high accident and death rates. This could help more efficient road safety management in Turkey.

  15. Road profiling of traffic accidents in Jos, Nigeria, 1995-1999.

    PubMed

    Bombom, Leonard S; Edino, Marcus O

    2009-09-01

    Road traffic accident data in Nigeria generally lack exact coordinate information. Accident analysis is, therefore, restricted to aggregate data on trends, magnitude and temporal dimensions. This article addresses the road accident problem in Jos between 1995 and 1999 through a road profiling approach. Results show that four gateway routes, seven multi-lane roadways (including two gateway routes) and seven road intersections accounted for 84% of all traffic accidents, 84% of injured casualties and 88% of fatalities. This approach allows for quantification of impacts of controlling for accidents by deliberate profiling of roads for close monitoring and policing. For example, reducing accident counts and fatalities by 50% each on gateway routes will amount to approximately 35 and 40% reduction in accident and fatality counts, respectively. Countermeasures must consider these roadways and intersections as important inputs in their accidents and casualty reduction targets.

  16. Indonesian railway accidents--utilizing Human Factors Analysis and Classification System in determining potential contributing factors.

    PubMed

    Iridiastadi, Hardianto; Ikatrinasari, Zulfa Fitri

    2012-01-01

    The prevalence of Indonesian railway accidents has not been declining, with hundreds of fatalities reported in the past decade. As an effort to help the National Transportation Safety Committee (NTSC), this study was conducted that aimed at understanding factors that might have contributed to the accidents. Human Factors Analysis and Classification System (HFACS) was utilized for this purpose. A total of nine accident reports (provided by the Indonesian NTSC) involving fatalities were studied using the technique. Results of this study indicated 72 factors that were closely related to the accidents. Of these, roughly 22% were considered as operator acts while about 39% were related to preconditions for operator acts. Supervisory represented 14% of the factors, and the remaining (about 25%) were associated with organizational factors. It was concluded that, while train drivers indeed played an important role in the accidents, interventions solely directed toward train drivers may not be adequate. A more comprehensive approach in minimizing the accidents should be conducted that addresses all the four aspects of HFACS.

  17. How perceptions of experience-based analysis influence explanations of work accidents.

    PubMed

    Mbaye, Safiétou; Kouabenan, Dongo Rémi

    2013-12-01

    This article looks into how perceptions of experience-based analysis (EBA) influence causal explanations of accidents given by managers and workers in the chemical industry (n=409) and in the nuclear industry (n=222). The approach is based on the model of naive explanations of accidents (Kouabenan, 1999, 2006, 2009), which recommends taking into account explanations of accidents spontaneously given by individuals, including laypersons, not only to better understand why accidents occur but also to design and implement the most appropriate prevention measures. The study reported here describes the impact of perceptions about EBA (perceived effectiveness, personal commitment, and the feeling of being involved in EBA practices) on managers' and workers' explanations of accidents likely to occur at the workplace. The results indicated that both managers and workers made more internal explanations than external ones when they perceived EBA positively. Moreover, the more the participants felt involved in EBA, were committed to it, and judged it effective, the more they explained accidents in terms of factors internal to the workers. Recommendations are proposed for reducing defensive reactions, increasing personal commitment to EBA, and improving EBA effectiveness. © 2013.

  18. The Driver Behaviour Questionnaire as accident predictor; A methodological re-meta-analysis.

    PubMed

    Af Wåhlberg, A E; Barraclough, P; Freeman, J

    2015-12-01

    The Manchester Driver Behaviour Questionnaire (DBQ) is the most commonly used self-report tool in traffic safety research and applied settings. It has been claimed that the violation factor of this instrument predicts accident involvement, which was supported by a previous meta-analysis. However, that analysis did not test for methodological effects, or include unpublished results. The present study re-analysed studies on prediction of accident involvement from DBQ factors, including lapses, and many unpublished effects. Tests of various types of dissemination bias and common method variance were undertaken. Outlier analysis showed that some effects were probably not reliable data, but excluding them did not change the results. For correlations between violations and crashes, tendencies for published effects to be larger than unpublished ones and for effects to decrease over time were observed, but were not significant. Also, using the mean of accidents as proxy for effect indicated that studies where effects for violations are not reported have smaller effect sizes. These differences indicate dissemination bias. Studies using self-reported accidents as dependent variables had much larger effects than those using recorded accident data. Also, zero-order correlations were larger than partial correlations controlled for exposure. Similarly, violations/accidents effects were strong only when there was also a strong correlation between accidents and exposure. Overall, the true effect is probably very close to zero (r<.07) for violations versus traffic accident involvement, depending upon which tendencies are controlled for. Methodological factors and dissemination bias have inflated the published effect sizes of the DBQ. Strong evidence of various artefactual effects is apparent. A greater level of care should be taken if the DBQ continues to be used in traffic safety research. Also, validation of self-reports should be more comprehensive in the future, taking into account the possibility of common method variance. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

  19. [Accidents in travellers - the hidden epidemic].

    PubMed

    Walz, Alexander; Hatz, Christoph

    2013-06-01

    The risk of malaria and other communicable diseases is well addressed in pre-travel advice. Accidents are usually less discussed. Thus, we aimed at assessing accident figures for the Swiss population, based on data of the register from 2004 to 2008 of the largest Swiss accident insurance organization (SUVA). More than 139'000 accidents over 5 years showed that 65 % of the accidents overseas are injuries, and 24 % are caused by poisoning or harm by cold, heat or air pressure. Most accidents happened during leisure activities or sports. More than one third of the non-lethal and more than 50 % of the fatal accidents happened in Asia. More than three-quarters of non-lethal accidents take place in people between 25 and 54 years. One out of 74 insured persons has an accident abroad per year. Despite of many analysis short-comings of the data set with regard to overseas travel, the figures document the underestimated burden of disease caused by accidents abroad and should affect the given pre-health advice.

  20. Human error analysis of commercial aviation accidents using the human factors analysis and classification system (HFACS)

    DOT National Transportation Integrated Search

    2001-02-01

    The Human Factors Analysis and Classification System (HFACS) is a general human error framework : originally developed and tested within the U.S. military as a tool for investigating and analyzing the human : causes of aviation accidents. Based upon ...

  1. Systemic accident analysis: examining the gap between research and practice.

    PubMed

    Underwood, Peter; Waterson, Patrick

    2013-06-01

    The systems approach is arguably the dominant concept within accident analysis research. Viewing accidents as a result of uncontrolled system interactions, it forms the theoretical basis of various systemic accident analysis (SAA) models and methods. Despite the proposed benefits of SAA, such as an improved description of accident causation, evidence within the scientific literature suggests that these techniques are not being used in practice and that a research-practice gap exists. The aim of this study was to explore the issues stemming from research and practice which could hinder the awareness, adoption and usage of SAA. To achieve this, semi-structured interviews were conducted with 42 safety experts from ten countries and a variety of industries, including rail, aviation and maritime. This study suggests that the research-practice gap should be closed and efforts to bridge the gap should focus on ensuring that systemic methods meet the needs of practitioners and improving the communication of SAA research. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Application of systems and control theory-based hazard analysis to radiation oncology.

    PubMed

    Pawlicki, Todd; Samost, Aubrey; Brown, Derek W; Manger, Ryan P; Kim, Gwe-Ya; Leveson, Nancy G

    2016-03-01

    Both humans and software are notoriously challenging to account for in traditional hazard analysis models. The purpose of this work is to investigate and demonstrate the application of a new, extended accident causality model, called systems theoretic accident model and processes (STAMP), to radiation oncology. Specifically, a hazard analysis technique based on STAMP, system-theoretic process analysis (STPA), is used to perform a hazard analysis. The STPA procedure starts with the definition of high-level accidents for radiation oncology at the medical center and the hazards leading to those accidents. From there, the hierarchical safety control structure of the radiation oncology clinic is modeled, i.e., the controls that are used to prevent accidents and provide effective treatment. Using STPA, unsafe control actions (behaviors) are identified that can lead to the hazards as well as causal scenarios that can lead to the identified unsafe control. This information can be used to eliminate or mitigate potential hazards. The STPA procedure is demonstrated on a new online adaptive cranial radiosurgery procedure that omits the CT simulation step and uses CBCT for localization, planning, and surface imaging system during treatment. The STPA procedure generated a comprehensive set of causal scenarios that are traced back to system hazards and accidents. Ten control loops were created for the new SRS procedure, which covered the areas of hospital and department management, treatment design and delivery, and vendor service. Eighty three unsafe control actions were identified as well as 472 causal scenarios that could lead to those unsafe control actions. STPA provides a method for understanding the role of management decisions and hospital operations on system safety and generating process design requirements to prevent hazards and accidents. The interaction of people, hardware, and software is highlighted. The method of STPA produces results that can be used to improve safety and prevent accidents and warrants further investigation.

  3. Deterministic chaotic dynamics of Raba River flow (Polish Carpathian Mountains)

    NASA Astrophysics Data System (ADS)

    Kędra, Mariola

    2014-02-01

    Is the underlying dynamics of river flow random or deterministic? If it is deterministic, is it deterministic chaotic? This issue is still controversial. The application of several independent methods, techniques and tools for studying daily river flow data gives consistent, reliable and clear-cut results to the question. The outcomes point out that the investigated discharge dynamics is not random but deterministic. Moreover, the results completely confirm the nonlinear deterministic chaotic nature of the studied process. The research was conducted on daily discharge from two selected gauging stations of the mountain river in southern Poland, the Raba River.

  4. Probabilistic structural analysis methods for space transportation propulsion systems

    NASA Technical Reports Server (NTRS)

    Chamis, C. C.; Moore, N.; Anis, C.; Newell, J.; Nagpal, V.; Singhal, S.

    1991-01-01

    Information on probabilistic structural analysis methods for space propulsion systems is given in viewgraph form. Information is given on deterministic certification methods, probability of failure, component response analysis, stress responses for 2nd stage turbine blades, Space Shuttle Main Engine (SSME) structural durability, and program plans. .

  5. CARDfile data base representativeness, Phase 1 : general characteristics including populations, vehicles, roads, and fatal accidents

    DOT National Transportation Integrated Search

    1988-08-01

    This report details the results of an analysis performed to evaluate the : representativeness of the Crash Avoidance Research accident data base : (CARDfile). The accident records for 1983 and 1984 from six states (Indiana, : Maryland, Michigan, Penn...

  6. CARDfile Data Base Representatives - Phase I: General Characteristics including Populations, Vehicles, Roads, and Fatal Accidents

    DOT National Transportation Integrated Search

    1985-12-01

    This report details the results of an analysis performed to evaluate the representativeness of the Crash Avoidance Research accident data base (CARDfile). The accident records for 1983 and 1984 from six states (Indiana, Maryland, Michigan, Pennsylvan...

  7. The Human Factors Analysis and Classification System : HFACS : final report.

    DOT National Transportation Integrated Search

    2000-02-01

    Human error has been implicated in 70 to 80% of all civil and military aviation accidents. Yet, most accident reporting systems are not designed around any theoretical framework of human error. As a result, most accident databases are not conducive t...

  8. Analysis of occupational accidents: prevention through the use of additional technical safety measures for machinery.

    PubMed

    Dźwiarek, Marek; Latała, Agata

    2016-01-01

    This article presents an analysis of results of 1035 serious and 341 minor accidents recorded by Poland's National Labour Inspectorate (PIP) in 2005-2011, in view of their prevention by means of additional safety measures applied by machinery users. Since the analysis aimed at formulating principles for the application of technical safety measures, the analysed accidents should bear additional attributes: the type of machine operation, technical safety measures and the type of events causing injuries. The analysis proved that the executed tasks and injury-causing events were closely connected and there was a relation between casualty events and technical safety measures. In the case of tasks consisting of manual feeding and collecting materials, the injuries usually occur because of the rotating motion of tools or crushing due to a closing motion. Numerous accidents also happened in the course of supporting actions, like removing pollutants, correcting material position, cleaning, etc.

  9. Analysis of occupational accidents: prevention through the use of additional technical safety measures for machinery

    PubMed Central

    Dźwiarek, Marek; Latała, Agata

    2016-01-01

    This article presents an analysis of results of 1035 serious and 341 minor accidents recorded by Poland's National Labour Inspectorate (PIP) in 2005–2011, in view of their prevention by means of additional safety measures applied by machinery users. Since the analysis aimed at formulating principles for the application of technical safety measures, the analysed accidents should bear additional attributes: the type of machine operation, technical safety measures and the type of events causing injuries. The analysis proved that the executed tasks and injury-causing events were closely connected and there was a relation between casualty events and technical safety measures. In the case of tasks consisting of manual feeding and collecting materials, the injuries usually occur because of the rotating motion of tools or crushing due to a closing motion. Numerous accidents also happened in the course of supporting actions, like removing pollutants, correcting material position, cleaning, etc. PMID:26652689

  10. Spatial study of mortality in motorcycle accidents in the State of Pernambuco, Northeastern Brazil.

    PubMed

    Silva, Paul Hindenburg Nobre de Vasconcelos; Lima, Maria Luiza Carvalho de; Moreira, Rafael da Silveira; Souza, Wayner Vieira de; Cabral, Amanda Priscila de Santana

    2011-04-01

    To analyze the spatial distribution of mortality due to motorcycle accidents in the state of Pernambuco, Northeastern Brazil. A population-based ecological study using data on mortality in motorcycle accidents from 01/01/2000 to 31/12/2005. The analysis units were the municipalities. For the spatial distribution analysis, an average mortality rate was calculated, using deaths from motorcycle accidents recorded in the Mortality Information System as the numerator, and as the denominator the population of the mid-period. Spatial analysis techniques, mortality smoothing coefficient estimate by the local empirical Bayesian method and Moran scatterplot, applied to the digital cartographic base of Pernambuco were used. The average mortality rate for motorcycle accidents in Pernambuco was 3.47 per 100 thousand inhabitants. Of the 185 municipalities, 16 were part of five clusters identified with average mortality rates ranging from 5.66 to 11.66 per 100 thousand inhabitants, and were considered critical areas. Three clusters are located in the area known as sertão and two in the agreste of the state. The risk of dying from a motorcycle accident is greater in conglomerate areas outside the metropolitan axis, and intervention measures should consider the economic, social and cultural contexts.

  11. Analyzing the causation of a railway accident based on a complex network

    NASA Astrophysics Data System (ADS)

    Ma, Xin; Li, Ke-Ping; Luo, Zi-Yan; Zhou, Jin

    2014-02-01

    In this paper, a new model is constructed for the causation analysis of railway accident based on the complex network theory. In the model, the nodes are defined as various manifest or latent accident causal factors. By employing the complex network theory, especially its statistical indicators, the railway accident as well as its key causations can be analyzed from the overall perspective. As a case, the “7.23” China—Yongwen railway accident is illustrated based on this model. The results show that the inspection of signals and the checking of line conditions before trains run played an important role in this railway accident. In conclusion, the constructed model gives a theoretical clue for railway accident prediction and, hence, greatly reduces the occurrence of railway accidents.

  12. Road accidents caused by sleepy drivers: Update of a Norwegian survey.

    PubMed

    Phillips, Ross Owen; Sagberg, Fridulv

    2013-01-01

    The current study tests, updates and expands a model of factors associated with sleepy driving, originally based on a 1997 survey of accident-involved Norwegian drivers (Sagberg, F., 1999. Road accidents caused by drivers falling asleep. Accident Analysis & Prevention 31, 639-649). The aim is to establish a robust model to inform measures to tackle sleepy driving. The original questions on (i) tiredness-related accidents and (ii) incidents of sleep behind the wheel in the last 12 months were again posed in 2003 and 2008, in independent surveys of Norwegian drivers involved in accidents reported to a large insurance company. According to those drivers at-fault for the accident, tiredness or sleepiness behind the wheel contributed to between 1.9 and 3.9 per cent of all types of accident reported to the insurance company across these years. Accident-involved drivers not at fault for the accident reported a reduction in the incidence of sleep behind the wheel for the preceding year, decreasing from 8.3 per cent in 1997 to 2.9 per cent in 2008. The reasons for this are not clear. According to logistic regression analysis of survey responses, the following factors were robustly associated with road accidents involving sleepy driving: driving off the road; good road conditions; longer distance driven since the start of the trip; and fewer years with a driving licence. The following factors are consistently associated with reports of sleep behind the wheel, whether or not it leads to an accident: being male; driving further per year; being younger; and having sleep-related health problems. Taken together these findings suggest that young, inexperienced male drivers who drive long distances may be a suitable target for road safety campaigns aimed at tackling sleepy driving. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Driving behaviors and on-duty road accidents: a French case-control study.

    PubMed

    Fort, Emmanuel; Chiron, Mireille; Davezies, Philippe; Bergeret, Alain; Charbotel, Barbara

    2013-01-01

    A case-control study was carried out to identify driving behaviors associated with the risk of on-duty road accident and to compare driving behaviors according to the type of journey (on duty, commuting, and private) for on-duty road accident victims. Cases were recruited from the Rhône Road Trauma Registry between January 2004 and October 2005 and were on duty at the time of the accident. Control subjects were recruited from the electoral rolls of the case subjects' constituencies of residence. Cases' and controls' driving behavior data were collected by self-administered questionnaire. A logistic regression was performed to identify behavioral risk factors for on-duty road accidents, taking into account age, sex, place of residence, road accident risk exposure, socio-occupational category, and type of road user. A second analysis focused specifically on the case subjects, comparing their self-assessed usual behaviors according to the type of journey. Significant factors for multivariate analysis of on-duty road accidents were female gender, history of on-duty road accidents during the previous 10 years, severe time pressure at work, and driving a vehicle not belonging to the driver. On-duty road accident victims reported behavioral risk factors more frequently in relation to driving for work than driving for private reasons or commuting: nonsystematic seat belt use, cell phone use at least once daily while driving, and history of accidents with injury during the previous 10 years. This study provides knowledge on behavioral risk factors for on-duty road accidents and differences in behavior according to the type of journey for subjects who have been on-duty road accident victims. These results will be useful for the design of on-duty road risk prevention.

  14. [Human risk factors and injuries due to road accidents: analysis of current data].

    PubMed

    Marchetti, Pierpaolo; Morandi, Anna; Lombardo, Carlo; Gigli Berzolari, Francesca; Bruno, Vincenzo; Marinoni, Alessandra

    2009-01-01

    several studies have shown that most road accidents are due to human factors, and that these are strongly linked to a drive's age and sex. The aim of this study is to test the role that some human factors play in road accidents by analysing current road accident data in the Province of Pavia, in Northern Italy. road accidents that occurred in 2004 were analysed by integrating the paper database of the vehicle licensing office, properly computerised, with the 911 database of the Province of Pavia. This study has been carried out by analysing 1.347 road accidents and the associated 2.908 drivers of motorised vehicles. Northern Italy, the Province of Pavia. the death rate of drivers of 2-wheeled vehicles is almost nine times higher than that of 4-wheeled vehicles. Analysis shows that females are twice as exposed to road accidents than males; it also shows the benefits of extensive road education training and of being aged 30-64 and older. Drivers who have already been punished and have had their driving license scores reduced are likely to respond rapidly when in a dangerous situation and also to be without blame after an accident. Motorcycle riders are 25 times more likely to suffer serious injury than drivers of cars. Additionally, the risk of a woman being seriously injured is higher than for a man. females, young drivers and motorcycle riders who have not previously been penalised for a previous traffic violation have a higher risk of being seriously injured; females and motorcycle riders are also at greater risk of being seriously injured. We hope that this analysis will be used to improve preventative interventions for road accidents.r.

  15. Epidemiology of Accidents in Tile Factories of Mangalore City in Karnataka

    PubMed Central

    Kumar, S Ganesh; Rathnakar, UP; Harsha Kumar, HN

    2010-01-01

    Background: Occupational accidents are a major point of concern in industries. The academic community should take the first step to address the long-neglected concerns of occupational safety. Objective: To assess the prevalence and pattern of occupational accidents. Materials and Methods: A record-based, cross-sectional study was done in three tile factories of Mangalore city, in Karnataka. A total of 416 workers were analyzed for the year 2004, and data regarding age, sex, job duration, type and nature of injury, body parts involved, and time of injury were collected in a prestructured proforma. Statistical Analysis: Proportions, Chi-square test, Univariate and Multivariate analysis. Results: The overall prevalence rate of accidents was found to be 18.5%. It was found that almost around 86% of the accidents had affected the limbs (upper limb 24.7%, lower limb 61%), around half (52%) of the injuries were contributed by superficial injuries, 40% of accidents were due to stepping/striking against objects and while handling. Hand tools and machinery in motion contributed to around 20% of the accidents. Accidents were more common among the younger age group and less-experienced workers. Multiple logistic regression analyses revealed that the age group of 30-39 years had an independent significant association with accidents (OR = 0.21, P = 0.04). Conclusion: Accidents in tile industries are an important occupational health problem in this area of the country. There is a need for proper safety training of the workers. PMID:20606926

  16. Injury protection and accident causation parameters for vulnerable road users based on German In-Depth Accident Study GIDAS.

    PubMed

    Otte, Dietmar; Jänsch, Michael; Haasper, Carl

    2012-01-01

    Within a study of accident data from GIDAS (German In-Depth Accident Study), vulnerable road users are investigated regarding injury risk in traffic accidents. GIDAS is the largest in-depth accident study in Germany. Due to a well-defined sampling plan, representativeness with respect to the federal statistics is also guaranteed. A hierarchical system ACASS (Accident Causation Analysis with Seven Steps) was developed in GIDAS, describing the human causation factors in a chronological sequence. The accordingly classified causation factors - derived from the systematic of the analysis of human accident causes ("7 steps") - can be used to describe the influence of accident causes on the injury outcome. The bases of the study are accident documentations over ten years from 1999 to 2008 with 8204 vulnerable road users (VRU), of which 3 different groups were selected as pedestrians n=2041, motorcyclists n=2199 and bicyclists n=3964, and analyzed on collisions with cars and trucks as well as vulnerable road users alone. The paper will give a description of the injury pattern and injury mechanisms of accidents. The injury frequencies and severities are pointed out considering different types of VRU and protective measures of helmet and clothes of the human body. The impact points are demonstrated on the car, following to conclusion of protective measures on the vehicle. Existing standards of protection devices as well as interdisciplinary research, including accident and injury statistics, are described. With this paper, a summarization of the existing possibilities on protective measures for pedestrians, bicyclists and motorcyclists is given and discussed by comparison of all three groups of vulnerable road users. Also the relevance of special impact situations and accident causes mainly responsible for severe injuries are pointed out, given the new orientation of research for the avoidance and reduction of accident patterns. 2010 Elsevier Ltd. All rights reserved.

  17. Reliability Analysis of Retaining Walls Subjected to Blast Loading by Finite Element Approach

    NASA Astrophysics Data System (ADS)

    GuhaRay, Anasua; Mondal, Stuti; Mohiuddin, Hisham Hasan

    2018-02-01

    Conventional design methods adopt factor of safety as per practice and experience, which are deterministic in nature. The limit state method, though not completely deterministic, does not take into account effect of design parameters, which are inherently variable such as cohesion, angle of internal friction, etc. for soil. Reliability analysis provides a measure to consider these variations into analysis and hence results in a more realistic design. Several studies have been carried out on reliability of reinforced concrete walls and masonry walls under explosions. Also, reliability analysis of retaining structures against various kinds of failure has been done. However, very few research works are available on reliability analysis of retaining walls subjected to blast loading. Thus, the present paper considers the effect of variation of geotechnical parameters when a retaining wall is subjected to blast loading. However, it is found that the variation of geotechnical random variables does not have a significant effect on the stability of retaining walls subjected to blast loading.

  18. Analysis of accident sequences and source terms at waste treatment and storage facilities for waste generated by U.S. Department of Energy Waste Management Operations, Volume 3: Appendixes C-H

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Mueller, C.; Nabelssi, B.; Roglans-Ribas, J.

    1995-04-01

    This report contains the Appendices for the Analysis of Accident Sequences and Source Terms at Waste Treatment and Storage Facilities for Waste Generated by the U.S. Department of Energy Waste Management Operations. The main report documents the methodology, computational framework, and results of facility accident analyses performed as a part of the U.S. Department of Energy (DOE) Waste Management Programmatic Environmental Impact Statement (WM PEIS). The accident sequences potentially important to human health risk are specified, their frequencies are assessed, and the resultant radiological and chemical source terms are evaluated. A personal computer-based computational framework and database have been developedmore » that provide these results as input to the WM PEIS for calculation of human health risk impacts. This report summarizes the accident analyses and aggregates the key results for each of the waste streams. Source terms are estimated and results are presented for each of the major DOE sites and facilities by WM PEIS alternative for each waste stream. The appendices identify the potential atmospheric release of each toxic chemical or radionuclide for each accident scenario studied. They also provide discussion of specific accident analysis data and guidance used or consulted in this report.« less

  19. Squeal Those Tires! Automobile-Accident Reconstruction.

    ERIC Educational Resources Information Center

    Caples, Linda Griffin

    1992-01-01

    Methods use to reconstruct traffic accidents provide settings for real life applications for students in precalculus, mathematical analysis, or trigonometry. Described is the investigation of an accident in conjunction with the local Highway Patrol Academy integrating physics, vector, and trigonometry. Class findings were compared with those of…

  20. A novel framework for improvement of road accidents considering decision-making styles of drivers in a large metropolitan area.

    PubMed

    Azadeh, Ali; Zarrin, Mansour; Hamid, Mehdi

    2016-02-01

    Road accidents can be caused by different factors such as human factors. Quality of the decision-making process of drivers could have a considerable impact on preventing disasters. The main objective of this study is the analysis of factors affecting road accidents by considering the severity of accidents and decision-making styles of drivers. To this end, a novel framework is proposed based on data envelopment analysis (DEA) and statistical methods (SMs) to assess the factors affecting road accidents. In this study, for the first time, dominant decision-making styles of drivers with respect to severity of injuries are identified. To show the applicability of the proposed framework, this research employs actual data of more than 500 samples in Tehran, Iran. The empirical results indicate that the flexible decision style is the dominant style for both minor and severe levels of accident injuries. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. [Comparative analysis of the radionuclide composition in fallout after the Chernobyl and the Fukushima accidents].

    PubMed

    Kotenko, K V; Shinkarev, S M; Abramov, Iu V; Granovskaia, E O; Iatsenko, V N; Gavrilin, Iu I; Margulis, U Ia; Garetskaia, O S; Imanaka, T; Khoshi, M

    2012-01-01

    The nuclear accident occurred at Fukushima Dai-ichi Nuclear Power Plant (NPP) (March 11, 2011) similarly to the accident at the Chernobyl NPP (April 26, 1986) is related to the level 7 of the INES. It is of interest to make an analysis of the radionuclide composition of the fallout following the both accidents. The results of the spectrometric measurements were used in that comparative analysis. Two areas following the Chernobyl accident were considered: (1) the near zone of the fallout - the Belarusian part of the central spot extended up to 60 km around the Chernobyl NPS and (2) the far zone of the fallout--the "Gomel-Mogilev" spot centered 200 km to the north-northeast of the damaged reactor. In the case of Fukushima accident the near zone up to about 60 km considered. The comparative analysis has been done with respect to refractory radionuclides (95Zr, 95Nb, 141Ce, 144Ce), as well as to the intermediate and volatile radionuclides 103Ru, 106Ru, 131I, 134Cs, 137Cs, 140La, 140Ba and the results of such a comparison have been discussed. With respect to exposure to the public the most important radionuclides are 131I and 137Cs. For the both accidents the ratios of 131I/137Cs in the considered soil samples are in the similar ranges: (3-50) for the Chernobyl samples and (5-70) for the Fukushima samples. Similarly to the Chernobyl accident a clear tendency that the ratio of 131I/137Cs in the fallout decreases with the increase of the ground deposition density of 137Cs within the trace related to a radioactive cloud has been identified for the Fukushima accident. It looks like this is a universal tendency for the ratio of 131I/137Cs versus the 137Cs ground deposition density in the fallout along the trace of a radioactive cloud as a result of a heavy accident at the NPP with radionuclides releases into the environment. This tendency is important for an objective reconstruction of 131I fallout based on the results of 137Cs measurements of soil samples carried out at late dates after the Fukushima accident.

  2. Bus incident reporting, tracking and analysis system

    DOT National Transportation Integrated Search

    2006-08-01

    Many Florida transit systems do little formal analysis of all accidents on an aggregate basis. In many transit system accidents and incidents are not being tracked or analyzed to identify common trends from types of incidents, location, driver, bus r...

  3. Road casualties in work-related and private contexts: Occupational medical impact: Results from the ESPARR cohort.

    PubMed

    Fort, E; Pélissier, C; Fanjas, A; Charnay, P; Charbotel, B; Bergeret, A; Fontana, L; Hours, M

    2018-05-22

    Road accidents may impact victims' physical and/or mental health and socio-occupational life, notably including return to work. To assess whether the occupational medical consequences sustained by subjects injured in road accidents occurring in a work-related context differ from those associated with private accidents. 778 adults who were in work or occupational training at the time of their accident were included. Two groups were distinguished: 354 (45.5%) injured in road accidents occurring in a work-related context (commuting or on duty) and 424 (54.5%) injured in a private accident. The groups were compared on medical and occupational factors assessed on prospective follow-up at 6 months and 1 and 3 years. Multivariate analysis explored for factors associated at 6 months and 1 year with sick leave following the accident and duration of sick leave. There were no significant differences between groups for demographic data apart from a slightly higher injury severity in private accidents (32.5% of private accidents with MAIS3+(Maximum Abbreviated Injury Scale greater or equal to 3) vs. 23.7% for work-related accidents, p = 0.007). Victims of work-related accidents were more often on sick leave (OR = 1.8; 95% CI, 1.1-2.9). Although the length of sick leave is higher for work-related accidents that for private accidents, multivariate analysis showed that the injury severity and the post-traumatic stress disorder (PTSD) are significant factors to explain the time to return to work. There were no significant differences according to occupational impact during follow-up, notably including sick-leave duration, number of victims returning to work within 3 years and number of victims out of work due to incapacity. In the ESPARR (follow-up study of a road-accident population in the Rhône administrative county: Etude de Suivi d'une Population d'Accidentés de la Route dans le Rhône) cohort, the fact that a road accident occurred in a work-related context did not affect the occupational consequences.

  4. Aircraft accidents : method of analysis

    NASA Technical Reports Server (NTRS)

    1929-01-01

    This report on a method of analysis of aircraft accidents has been prepared by a special committee on the nomenclature, subdivision, and classification of aircraft accidents organized by the National Advisory Committee for Aeronautics in response to a request dated February 18, 1928, from the Air Coordination Committee consisting of the Assistant Secretaries for Aeronautics in the Departments of War, Navy, and Commerce. The work was undertaken in recognition of the difficulty of drawing correct conclusions from efforts to analyze and compare reports of aircraft accidents prepared by different organizations using different classifications and definitions. The air coordination committee's request was made "in order that practices used may henceforth conform to a standard and be universally comparable." the purpose of the special committee therefore was to prepare a basis for the classification and comparison of aircraft accidents, both civil and military. (author)

  5. Signal Processing Applications Of Wigner-Ville Analysis

    NASA Astrophysics Data System (ADS)

    Whitehouse, H. J.; Boashash, B.

    1986-04-01

    The Wigner-Ville distribution (WVD), a form of time-frequency analysis, is shown to be useful in the analysis of a variety of non-stationary signals both deterministic and stochastic. The properties of the WVD are reviewed and alternative methods of calculating the WVD are discussed. Applications are presented.

  6. [The characteristics of computer simulation of traffic accidents].

    PubMed

    Zou, Dong-Hua; Liu, Ning-Guo; Chen, Jian-Guo; Jin, Xian-Long; Zhang, Xiao-Yun; Zhang, Jian-Hua; Chen, Yi-Jiu

    2008-12-01

    To reconstruct the collision process of traffic accident and the injury mode of the victim by computer simulation technology in forensic assessment of traffic accident. Forty actual accidents were reconstructed by stimulation software and high performance computer based on analysis of the trace evidences at the scene, damage of the vehicles and injury of the victims, with 2 cases discussed in details. The reconstruction correlated very well in 28 cases, well in 9 cases, and suboptimal in 3 cases with the above parameters. Accurate reconstruction of the accident would be helpful for assessment of the injury mechanism of the victims. Reconstruction of the collision process of traffic accident and the injury mechanism of the victim by computer simulation is useful in traffic accident assessment.

  7. Risk of road accident associated with the use of drugs: a systematic review and meta-analysis of evidence from epidemiological studies.

    PubMed

    Elvik, Rune

    2013-11-01

    This paper is a corrigendum to a previously published paper where errors were detected. The errors have been corrected in this paper. The paper is otherwise identical to the previously published paper. A systematic review and meta-analysis of studies that have assessed the risk of accident associated with the use of drugs when driving is presented. The meta-analysis included 66 studies containing a total of 264 estimates of the effects on accident risk of using illicit or prescribed drugs when driving. Summary estimates of the odds ratio of accident involvement are presented for amphetamines, analgesics, anti-asthmatics, anti-depressives, anti-histamines, benzodiazepines, cannabis, cocaine, opiates, penicillin and zopiclone (a sleeping pill). For most of the drugs, small or moderate increases in accident risk associated with the use of the drugs were found. Information about whether the drugs were actually used while driving and about the doses used was often imprecise. Most studies that have evaluated the presence of a dose-response relationship between the dose of drugs taken and the effects on accident risk confirm the existence of a dose-response relationship. Use of drugs while driving tends to have a larger effect on the risk of fatal and serious injury accidents than on the risk of less serious accidents (usually property-damage-only accidents). The quality of the studies that have assessed risk varied greatly. There was a tendency for the estimated effects of drug use on accident risk to be smaller in well-controlled studies than in poorly controlled studies. Evidence of publication bias was found for some drugs. The associations found cannot be interpreted as causal relationships, principally because most studies do not control very well for potentially confounding factors. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Primary school accident reporting in one education authority

    PubMed Central

    Latif, A; Williams, W; Sibert, J

    2002-01-01

    Background: Studies have shown a correlation between increased accident rates and levels of deprivation in the community. School accident reporting is one area where an association might be expected. Aims: To investigate differences in primary school accident rates in deprived and more affluent wards, in an area managed by one education authority. Methods: Statistical analysis of accident form returns for 100 primary schools in one education authority in Wales over a two year period, in conjunction with visits to over one third of school sites. Results: Accident report rates from schools in deprived wards were three times higher than those from schools in more affluent wards. School visits showed that this discrepancy was attributable primarily to differences in reporting procedures. One third of schools did not report accidents and approximately half did not keep records of minor accidents. Conclusions: The association between school accident report rates and deprivation in the community is complex. School accident data from local education authorities may be unreliable for most purposes of collection. PMID:11827900

  9. Primary school accident reporting in one education authority.

    PubMed

    Latif, A H A; Williams, W R; Sibert, J

    2002-02-01

    Studies have shown a correlation between increased accident rates and levels of deprivation in the community. School accident reporting is one area where an association might be expected. To investigate differences in primary school accident rates in deprived and more affluent wards, in an area managed by one education authority. Statistical analysis of accident form returns for 100 primary schools in one education authority in Wales over a two year period, in conjunction with visits to over one third of school sites. Accident report rates from schools in deprived wards were three times higher than those from schools in more affluent wards. School visits showed that this discrepancy was attributable primarily to differences in reporting procedures. One third of schools did not report accidents and approximately half did not keep records of minor accidents. The association between school accident report rates and deprivation in the community is complex. School accident data from local education authorities may be unreliable for most purposes of collection.

  10. Learning lessons from Natech accidents - the eNATECH accident database

    NASA Astrophysics Data System (ADS)

    Krausmann, Elisabeth; Girgin, Serkan

    2016-04-01

    When natural hazards impact industrial facilities that house or process hazardous materials, fires, explosions and toxic releases can occur. This type of accident is commonly referred to as Natech accident. In order to prevent the recurrence of accidents or to better mitigate their consequences, lessons-learned type studies using available accident data are usually carried out. Through post-accident analysis, conclusions can be drawn on the most common damage and failure modes and hazmat release paths, particularly vulnerable storage and process equipment, and the hazardous materials most commonly involved in these types of accidents. These analyses also lend themselves to identifying technical and organisational risk-reduction measures that require improvement or are missing. Industrial accident databases are commonly used for retrieving sets of Natech accident case histories for further analysis. These databases contain accident data from the open literature, government authorities or in-company sources. The quality of reported information is not uniform and exhibits different levels of detail and accuracy. This is due to the difficulty of finding qualified information sources, especially in situations where accident reporting by the industry or by authorities is not compulsory, e.g. when spill quantities are below the reporting threshold. Data collection has then to rely on voluntary record keeping often by non-experts. The level of detail is particularly non-uniform for Natech accident data depending on whether the consequences of the Natech event were major or minor, and whether comprehensive information was available for reporting. In addition to the reporting bias towards high-consequence events, industrial accident databases frequently lack information on the severity of the triggering natural hazard, as well as on failure modes that led to the hazmat release. This makes it difficult to reconstruct the dynamics of the accident and renders the development of equipment vulnerability models linking the natural-hazard severity to the observed damage almost impossible. As a consequence, the European Commission has set up the eNATECH database for the systematic collection of Natech accident data and near misses. The database exhibits the more sophisticated accident representation required to capture the characteristics of Natech events and is publicly accessible at http://enatech.jrc.ec.europa.eu. This presentation outlines the general lessons-learning process, introduces the eNATECH database and its specific structure, and discusses natural-hazard specific lessons learned and features common to Natech accidents triggered by different natural hazards.

  11. Discrete Deterministic and Stochastic Petri Nets

    NASA Technical Reports Server (NTRS)

    Zijal, Robert; Ciardo, Gianfranco

    1996-01-01

    Petri nets augmented with timing specifications gained a wide acceptance in the area of performance and reliability evaluation of complex systems exhibiting concurrency, synchronization, and conflicts. The state space of time-extended Petri nets is mapped onto its basic underlying stochastic process, which can be shown to be Markovian under the assumption of exponentially distributed firing times. The integration of exponentially and non-exponentially distributed timing is still one of the major problems for the analysis and was first attacked for continuous time Petri nets at the cost of structural or analytical restrictions. We propose a discrete deterministic and stochastic Petri net (DDSPN) formalism with no imposed structural or analytical restrictions where transitions can fire either in zero time or according to arbitrary firing times that can be represented as the time to absorption in a finite absorbing discrete time Markov chain (DTMC). Exponentially distributed firing times are then approximated arbitrarily well by geometric distributions. Deterministic firing times are a special case of the geometric distribution. The underlying stochastic process of a DDSPN is then also a DTMC, from which the transient and stationary solution can be obtained by standard techniques. A comprehensive algorithm and some state space reduction techniques for the analysis of DDSPNs are presented comprising the automatic detection of conflicts and confusions, which removes a major obstacle for the analysis of discrete time models.

  12. Study of Benefits of Passenger Protective Breathing Equipment from Analysis of Past Accidents

    DTIC Science & Technology

    1988-03-01

    Rodeos (Tenerife) El 27 De Marzo De 1977 2. ICAO Aircraft Accident Digest No. 23, No. 2 B-30 AIRCRAFT ACCIDENT SUMMARY Carrier - Continental Airways...than FPL. However, a I’)-second donning de -lay of PBE may have resulted in a net disbenefit. k~f ¶ ~ 17. Key Words 18. Distributiion Stotement...in C-133 Test Article 23 with Postcrash Fire Conditions 5 Accident Profiles for 3/5/67 Varig DC-8 24 6 Accident Profiles for 4/8/68 British Overseas

  13. Tobit analysis of vehicle accident rates on interstate highways.

    PubMed

    Anastasopoulos, Panagiotis Ch; Tarko, Andrew P; Mannering, Fred L

    2008-03-01

    There has been an abundance of research that has used Poisson models and its variants (negative binomial and zero-inflated models) to improve our understanding of the factors that affect accident frequencies on roadway segments. This study explores the application of an alternate method, tobit regression, by viewing vehicle accident rates directly (instead of frequencies) as a continuous variable that is left-censored at zero. Using data from vehicle accidents on Indiana interstates, the estimation results show that many factors relating to pavement condition, roadway geometrics and traffic characteristics significantly affect vehicle accident rates.

  14. Analysis of traffic crash data in Kentucky : 2002-2006.

    DOT National Transportation Integrated Search

    2007-09-01

    This report includes an analysis of traffic accident data in Kentucky for the years of 2002 through 2006. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

  15. Analysis of traffic crash data in Kentucky : 2003-2007.

    DOT National Transportation Integrated Search

    2008-08-01

    This report includes an analysis of traffic accident data in Kentucky for the years of 2003 through 2007. A primary objective of this study was to determine average accident statistics for Kentucky highways. Average and critical numbers and rates of ...

  16. A Look at Aircraft Accident Analysis in the Early Days: Do Early 20th Century Accident Investigation Techniques Have Any Lessons for Today?

    NASA Technical Reports Server (NTRS)

    Holloway, C. M.; Johnson, C. W.

    2007-01-01

    In the early years of powered flight, the National Advisory Committee on Aeronautics in the United States produced three reports describing a method of analysis of aircraft accidents. The first report was published in 1928; the second, which was a revision of the first, was published in 1930; and the third, which was a revision and update of the second, was published in 1936. This paper describes the contents of these reports, and compares the method of analysis proposed therein to the methods used today.

  17. Analysis of unmitigated large break loss of coolant accidents using MELCOR code

    NASA Astrophysics Data System (ADS)

    Pescarini, M.; Mascari, F.; Mostacci, D.; De Rosa, F.; Lombardo, C.; Giannetti, F.

    2017-11-01

    In the framework of severe accident research activity developed by ENEA, a MELCOR nodalization of a generic Pressurized Water Reactor of 900 MWe has been developed. The aim of this paper is to present the analysis of MELCOR code calculations concerning two independent unmitigated large break loss of coolant accident transients, occurring in the cited type of reactor. In particular, the analysis and comparison between the transients initiated by an unmitigated double-ended cold leg rupture and an unmitigated double-ended hot leg rupture in the loop 1 of the primary cooling system is presented herein. This activity has been performed focusing specifically on the in-vessel phenomenology that characterizes this kind of accidents. The analysis of the thermal-hydraulic transient phenomena and the core degradation phenomena is therefore here presented. The analysis of the calculated data shows the capability of the code to reproduce the phenomena typical of these transients and permits their phenomenological study. A first sequence of main events is here presented and shows that the cold leg break transient results faster than the hot leg break transient because of the position of the break. Further analyses are in progress to quantitatively assess the results of the code nodalization for accident management strategy definition and fission product source term evaluation.

  18. Economic analysis of interventions to improve village chicken production in Myanmar.

    PubMed

    Henning, J; Morton, J; Pym, R; Hla, T; Sunn, K; Meers, J

    2013-07-01

    A cost-benefit analysis using deterministic and stochastic modelling was conducted to identify the net benefits for households that adopt (1) vaccination of individual birds against Newcastle disease (ND) or (2) improved management of chick rearing by providing coops for the protection of chicks from predation and chick starter feed inside a creep feeder to support chicks' nutrition in village chicken flocks in Myanmar. Partial budgeting was used to assess the additional costs and benefits associated with each of the two interventions tested relative to neither strategy. In the deterministic model, over the first 3 years after the introduction of the interventions, the cumulative sum of the net differences from neither strategy was 13,189Kyat for ND vaccination and 77,645Kyat for improved chick management (effective exchange rate in 2005: 1000Kyat=1$US). Both interventions were also profitable after discounting over a 10-year period; Net Present Values for ND vaccination and improved chick management were 30,791 and 167,825Kyat, respectively. The Benefit-Cost Ratio for ND vaccination was very high (28.8). This was lower for improved chick management, due to greater costs of the intervention, but still favourable at 4.7. Using both interventions concurrently yielded a Net Present Value of 470,543Kyat and a Benefit-Cost Ratio of 11.2 over the 10-year period in the deterministic model. Using the stochastic model, for the first 3 years following the introduction of the interventions, the mean cumulative sums of the net difference were similar to those values obtained from the deterministic model. Sensitivity analysis indicated that the cumulative net differences were strongly influenced by grower bird sale income, particularly under improved chick management. The effects of the strategies on odds of households selling and consuming birds after 7 months, and numbers of birds being sold or consumed after this period also influenced profitability. Cost variations for equipment used under improved chick management were not markedly associated with profitability. Net Present Values and Benefit-Cost Ratios discounted over a 10-year period were also similar to the deterministic model when mean values obtained through stochastic modelling were used. In summary, the study showed that ND vaccination and improved chick management can improve the viability and profitability of village chicken production in Myanmar. Copyright © 2013 Elsevier B.V. All rights reserved.

  19. Analysis of National Major Work Safety Accidents in China, 2003–2012

    PubMed Central

    YE, Yunfeng; ZHANG, Siheng; RAO, Jiaming; WANG, Haiqing; LI, Yang; WANG, Shengyong; DONG, Xiaomei

    2016-01-01

    Background: This study provides a national profile of major work safety accidents in China, which cause more than 10 fatalities per accident, intended to provide scientific basis for prevention measures and strategies to reduce major work safety accidents and deaths. Methods: Data from 2003–2012 Census of major work safety accidents were collected from State Administration of Work Safety System (SAWS). Published literature and statistical yearbook were also included to implement information. We analyzed the frequency of accidents and deaths, trend, geographic distribution and injury types. Additionally, we discussed the severity and urgency of emergency rescue by types of accidents. Results: A total of 877 major work safety accidents were reported, resulting in 16,795 deaths and 9,183 injuries. The numbers of accidents and deaths, mortality rate and incidence of major accidents have declined in recent years. The mortality rate and incidence was 0.71 and 1.20 per 106 populations in 2012, respectively. Transportation and mining contributed to the highest number of major accidents and deaths. Major aviation and railway accidents caused more casualties per incident, while collapse, machinery, electrical shock accidents and tailing dam accidents were the most severe situation that resulted in bigger proportion of death. Conclusion: Ten years’ major work safety accident data indicate that the frequency of accidents and number of eaths was declined and several safety concerns persist in some segments. PMID:27057515

  20. Robust Fixed-Structure Control

    DTIC Science & Technology

    1994-10-30

    Deterministic Foundation for Statistical Energy Analysis ," J. Sound Vibr., to appear. 1.96 D. S. Bernstein and S. P. Bhat, "Lyapunov Stability, Semistability...S. Bernstein, "Power Flow, Energy Balance, and Statistical Energy Analysis for Large Scale, Interconnected Systems," Proc. Amer. Contr. Conf., pp

  1. Combining Deterministic structures and stochastic heterogeneity for transport modeling

    NASA Astrophysics Data System (ADS)

    Zech, Alraune; Attinger, Sabine; Dietrich, Peter; Teutsch, Georg

    2017-04-01

    Contaminant transport in highly heterogeneous aquifers is extremely challenging and subject of current scientific debate. Tracer plumes often show non-symmetric but highly skewed plume shapes. Predicting such transport behavior using the classical advection-dispersion-equation (ADE) in combination with a stochastic description of aquifer properties requires a dense measurement network. This is in contrast to the available information for most aquifers. A new conceptual aquifer structure model is presented which combines large-scale deterministic information and the stochastic approach for incorporating sub-scale heterogeneity. The conceptual model is designed to allow for a goal-oriented, site specific transport analysis making use of as few data as possible. Thereby the basic idea is to reproduce highly skewed tracer plumes in heterogeneous media by incorporating deterministic contrasts and effects of connectivity instead of using unimodal heterogeneous models with high variances. The conceptual model consists of deterministic blocks of mean hydraulic conductivity which might be measured by pumping tests indicating values differing in orders of magnitudes. A sub-scale heterogeneity is introduced within every block. This heterogeneity can be modeled as bimodal or log-normal distributed. The impact of input parameters, structure and conductivity contrasts is investigated in a systematic manor. Furthermore, some first successful implementation of the model was achieved for the well known MADE site.

  2. Demographic noise can reverse the direction of deterministic selection

    PubMed Central

    Constable, George W. A.; Rogers, Tim; McKane, Alan J.; Tarnita, Corina E.

    2016-01-01

    Deterministic evolutionary theory robustly predicts that populations displaying altruistic behaviors will be driven to extinction by mutant cheats that absorb common benefits but do not themselves contribute. Here we show that when demographic stochasticity is accounted for, selection can in fact act in the reverse direction to that predicted deterministically, instead favoring cooperative behaviors that appreciably increase the carrying capacity of the population. Populations that exist in larger numbers experience a selective advantage by being more stochastically robust to invasions than smaller populations, and this advantage can persist even in the presence of reproductive costs. We investigate this general effect in the specific context of public goods production and find conditions for stochastic selection reversal leading to the success of public good producers. This insight, developed here analytically, is missed by the deterministic analysis as well as by standard game theoretic models that enforce a fixed population size. The effect is found to be amplified by space; in this scenario we find that selection reversal occurs within biologically reasonable parameter regimes for microbial populations. Beyond the public good problem, we formulate a general mathematical framework for models that may exhibit stochastic selection reversal. In this context, we describe a stochastic analog to r−K theory, by which small populations can evolve to higher densities in the absence of disturbance. PMID:27450085

  3. Hydraulic tomography of discrete networks of conduits and fractures in a karstic aquifer by using a deterministic inversion algorithm

    NASA Astrophysics Data System (ADS)

    Fischer, P.; Jardani, A.; Lecoq, N.

    2018-02-01

    In this paper, we present a novel inverse modeling method called Discrete Network Deterministic Inversion (DNDI) for mapping the geometry and property of the discrete network of conduits and fractures in the karstified aquifers. The DNDI algorithm is based on a coupled discrete-continuum concept to simulate numerically water flows in a model and a deterministic optimization algorithm to invert a set of observed piezometric data recorded during multiple pumping tests. In this method, the model is partioned in subspaces piloted by a set of parameters (matrix transmissivity, and geometry and equivalent transmissivity of the conduits) that are considered as unknown. In this way, the deterministic optimization process can iteratively correct the geometry of the network and the values of the properties, until it converges to a global network geometry in a solution model able to reproduce the set of data. An uncertainty analysis of this result can be performed from the maps of posterior uncertainties on the network geometry or on the property values. This method has been successfully tested for three different theoretical and simplified study cases with hydraulic responses data generated from hypothetical karstic models with an increasing complexity of the network geometry, and of the matrix heterogeneity.

  4. A study of carburetor/induction system icing in general aviation accidents

    NASA Technical Reports Server (NTRS)

    Obermayer, R. W.; Roe, W. T.

    1975-01-01

    An assessment of the frequency and severity of carburetor/induction icing in general-aviation accidents was performed. The available literature and accident data from the National Transportation Safety Board were collected. A computer analysis of the accident data was performed. Between 65 and 90 accidents each year involve carburetor/induction system icing as a probable cause/factor. Under conditions conducive to carburetor/induction icing, between 50 and 70 percent of engine malfunction/failure accidents (exclusive of those due to fuel exhaustion) are due to carburetor/induction system icing. Since the evidence of such icing may not remain long after an accident, it is probable that the frequency of occurrence of such accidents is underestimated; therefore, some extrapolation of the data was conducted. The problem of carburetor/induction system icing is particularly acute for pilots with less than 1000 hours of total flying time. The severity of such accidents is about the same as any accident resulting from a forced landing or precautionary landing. About 144 persons, on the average, are exposed to death and injury each year in accidents involving carburetor/induction icing as a probable cause/factor.

  5. Secondary school accident reporting in one education authority.

    PubMed

    Williams, W R; Latif, A H A; Sibert, J

    2002-01-01

    Secondary schools appear to have very different accident rates when they are compared on the basis of accident report returns. The variation may be as a result of real differences in accident rates or different reporting procedures. This study investigates accident reporting from secondary schools and, in particular, the role of the school nurse. Accident form returns covering a 2-year period were collected for statistical analysis from 13 comprehensive schools in one local education authority in Wales. School sites were visited in the following school year to obtain information about accident records held on site and accident reporting procedures. The main factors determining the number of school accident reports submitted to the education authority relate to differences in recording and reporting procedures, such as the employment of a nurse and the policy of the head teacher/safety officer on submitting accident returns. Accident and emergency department referrals from similar schools may show significant differences in specific injuries and their causes. The level of school accident activity cannot be gauged from reports submitted to the education authority. Lack of incentives for collecting good accident data, in conjunction with the degree of complacency in the current system, suggest that future accident rates and reporting activity are unlikely to change.

  6. Understanding transit accidents using the National Transit Database and the role of Transit Intelligent Vehicle Initiative Technology in reducing accidents

    DOT National Transportation Integrated Search

    2004-06-01

    This report documents the results of bus accident data analysis using the 2002 National Transit Database (NTD) and discusses the potential of using advanced technology being studied and developed under the U.S. Department of Transportations (U.S. ...

  7. Phase 2 : evaluation of the national crash experience : comparison of CARDfile national motor vehicle accident projections with projections from NASS

    DOT National Transportation Integrated Search

    1987-07-01

    This report details the results of an analysis that compared the Crash Avoidance : Research Data Base (CARDfile) with the National Accident Sampling System (NASS). : CARDfile combines, in one data base, the police accident records for three years : (...

  8. Stochastic flux analysis of chemical reaction networks

    PubMed Central

    2013-01-01

    Background Chemical reaction networks provide an abstraction scheme for a broad range of models in biology and ecology. The two common means for simulating these networks are the deterministic and the stochastic approaches. The traditional deterministic approach, based on differential equations, enjoys a rich set of analysis techniques, including a treatment of reaction fluxes. However, the discrete stochastic simulations, which provide advantages in some cases, lack a quantitative treatment of network fluxes. Results We describe a method for flux analysis of chemical reaction networks, where flux is given by the flow of species between reactions in stochastic simulations of the network. Extending discrete event simulation algorithms, our method constructs several data structures, and thereby reveals a variety of statistics about resource creation and consumption during the simulation. We use these structures to quantify the causal interdependence and relative importance of the reactions at arbitrary time intervals with respect to the network fluxes. This allows us to construct reduced networks that have the same flux-behavior, and compare these networks, also with respect to their time series. We demonstrate our approach on an extended example based on a published ODE model of the same network, that is, Rho GTP-binding proteins, and on other models from biology and ecology. Conclusions We provide a fully stochastic treatment of flux analysis. As in deterministic analysis, our method delivers the network behavior in terms of species transformations. Moreover, our stochastic analysis can be applied, not only at steady state, but at arbitrary time intervals, and used to identify the flow of specific species between specific reactions. Our cases study of Rho GTP-binding proteins reveals the role played by the cyclic reverse fluxes in tuning the behavior of this network. PMID:24314153

  9. Stochastic flux analysis of chemical reaction networks.

    PubMed

    Kahramanoğulları, Ozan; Lynch, James F

    2013-12-07

    Chemical reaction networks provide an abstraction scheme for a broad range of models in biology and ecology. The two common means for simulating these networks are the deterministic and the stochastic approaches. The traditional deterministic approach, based on differential equations, enjoys a rich set of analysis techniques, including a treatment of reaction fluxes. However, the discrete stochastic simulations, which provide advantages in some cases, lack a quantitative treatment of network fluxes. We describe a method for flux analysis of chemical reaction networks, where flux is given by the flow of species between reactions in stochastic simulations of the network. Extending discrete event simulation algorithms, our method constructs several data structures, and thereby reveals a variety of statistics about resource creation and consumption during the simulation. We use these structures to quantify the causal interdependence and relative importance of the reactions at arbitrary time intervals with respect to the network fluxes. This allows us to construct reduced networks that have the same flux-behavior, and compare these networks, also with respect to their time series. We demonstrate our approach on an extended example based on a published ODE model of the same network, that is, Rho GTP-binding proteins, and on other models from biology and ecology. We provide a fully stochastic treatment of flux analysis. As in deterministic analysis, our method delivers the network behavior in terms of species transformations. Moreover, our stochastic analysis can be applied, not only at steady state, but at arbitrary time intervals, and used to identify the flow of specific species between specific reactions. Our cases study of Rho GTP-binding proteins reveals the role played by the cyclic reverse fluxes in tuning the behavior of this network.

  10. Protein Aggregation/Folding: The Role of Deterministic Singularities of Sequence Hydrophobicity as Determined by Nonlinear Signal Analysis of Acylphosphatase and Aβ(1–40)

    PubMed Central

    Zbilut, Joseph P.; Colosimo, Alfredo; Conti, Filippo; Colafranceschi, Mauro; Manetti, Cesare; Valerio, MariaCristina; Webber, Charles L.; Giuliani, Alessandro

    2003-01-01

    The problem of protein folding vs. aggregation was investigated in acylphosphatase and the amyloid protein Aβ(1–40) by means of nonlinear signal analysis of their chain hydrophobicity. Numerical descriptors of recurrence patterns provided the basis for statistical evaluation of folding/aggregation distinctive features. Static and dynamic approaches were used to elucidate conditions coincident with folding vs. aggregation using comparisons with known protein secondary structure classifications, site-directed mutagenesis studies of acylphosphatase, and molecular dynamics simulations of amyloid protein, Aβ(1–40). The results suggest that a feature derived from principal component space characterized by the smoothness of singular, deterministic hydrophobicity patches plays a significant role in the conditions governing protein aggregation. PMID:14645049

  11. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  12. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  13. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  14. 10 CFR 830.204 - Documented safety analysis.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ..., and accident conditions, including consideration of natural and man-made external events... radioactive and other hazardous materials, and consideration of the need for analysis of accidents which may... preparedness, fire protection, waste management, and radiation protection; and (6) With respect to a nonreactor...

  15. A Human Factors Analysis of USAF Remotely Piloted Aircraft Mishaps

    DTIC Science & Technology

    2013-06-01

    conditions or unsafe acts, where their respective removal would prevent a chain reaction from propagating, thus preventing the accident . This model...Force Col. Anthony Tvaryanas stated that “If you 19 really wanted to make a dent in preventing RPA accidents , the DoD needs to look at how they do...REFERENCES Greenwood, M. & Woods, H.M. (1919). The incidence of industrial accidents upon individuals with special reference to multiple accidents . (British

  16. Location of coating defects and assessment of level of cathodic protection on underground pipelines using AC impedance, deterministic and non-deterministic models

    NASA Astrophysics Data System (ADS)

    Castaneda-Lopez, Homero

    A methodology for detecting and locating defects or discontinuities on the outside covering of coated metal underground pipelines subjected to cathodic protection has been addressed. On the basis of wide range AC impedance signals for various frequencies applied to a steel-coated pipeline system and by measuring its corresponding transfer function under several laboratory simulation scenarios, a physical laboratory setup of an underground cathodic-protected, coated pipeline was built. This model included different variables and elements that exist under real conditions, such as soil resistivity, soil chemical composition, defect (holiday) location in the pipeline covering, defect area and geometry, and level of cathodic protection. The AC impedance data obtained under different working conditions were used to fit an electrical transmission line model. This model was then used as a tool to fit the impedance signal for different experimental conditions and to establish trends in the impedance behavior without the necessity of further experimental work. However, due to the chaotic nature of the transfer function response of this system under several conditions, it is believed that non-deterministic models based on pattern recognition algorithms are suitable for field condition analysis. A non-deterministic approach was used for experimental analysis by applying an artificial neural network (ANN) algorithm based on classification analysis capable of studying the pipeline system and differentiating the variables that can change impedance conditions. These variables include level of cathodic protection, location of discontinuities (holidays), and severity of corrosion. This work demonstrated a proof-of-concept for a well-known technique and a novel algorithm capable of classifying impedance data for experimental results to predict the exact location of the active holidays and defects on the buried pipelines. Laboratory findings from this procedure are promising, and efforts to develop it for field conditions should continue.

  17. Hazmat transport: a methodological framework for the risk analysis of marshalling yards.

    PubMed

    Cozzani, Valerio; Bonvicini, Sarah; Spadoni, Gigliola; Zanelli, Severino

    2007-08-17

    A methodological framework was outlined for the comprehensive risk assessment of marshalling yards in the context of quantified area risk analysis. Three accident typologies were considered for yards: (i) "in-transit-accident-induced" releases; (ii) "shunting-accident-induced" spills; and (iii) "non-accident-induced" leaks. A specific methodology was developed for the assessment of expected release frequencies and equivalent release diameters, based on the application of HazOp and Fault Tree techniques to reference schemes defined for the more common types of railcar vessels used for "hazmat" transportation. The approach was applied to the assessment of an extended case-study. The results evidenced that "non-accident-induced" leaks in marshalling yards represent an important contribution to the overall risk associated to these zones. Furthermore, the results confirmed the considerable role of these fixed installations to the overall risk associated to "hazmat" transportation.

  18. Vulnerability assessment of chemical industry facilities in South Korea based on the chemical accident history

    NASA Astrophysics Data System (ADS)

    Heo, S.; Lee, W. K.; Jong-Ryeul, S.; Kim, M. I.

    2016-12-01

    The use of chemical compounds are keep increasing because of their use in manufacturing industry. Chemical accident is growing as the consequence of the chemical use increment. Devastating damages from chemical accidents are far enough to aware people's cautious about the risk of the chemical accident. In South Korea, Gumi Hydrofluoric acid leaking accident triggered the importance of risk management and emphasized the preventing the accident over the damage reducing process after the accident occurs. Gumi accident encouraged the government data base construction relate to the chemical accident. As the result of this effort Chemical Safety-Clearing-house (CSC) have started to record the chemical accident information and damages according to the Harmful Chemical Substance Control Act (HCSC). CSC provide details information about the chemical accidents from 2002 to present. The detail informations are including title of company, address, business type, accident dates, accident types, accident chemical compounds, human damages inside of the chemical industry facilities, human damage outside of the chemical industry facilities, financial damages inside of the chemical industry facilities, and financial damages outside of the chemical industry facilities, environmental damages and response to the chemical accident. Collected the chemical accident history of South Korea from 2002 to 2015 and provide the spatial information to the each accident records based on their address. With the spatial information, compute the data on ArcGIS for the spatial-temporal analysis. The spatial-temporal information of chemical accident is organized by the chemical accident types, damages, and damages on environment and conduct the spatial proximity with local community and environmental receptors. Find the chemical accident vulnerable area of South Korea from 2002 to 2015 and add the vulnerable area of total period to examine the historically vulnerable area from the chemical accident in South Korea.

  19. Pattern extraction for high-risk accidents in the construction industry: a data-mining approach.

    PubMed

    Amiri, Mehran; Ardeshir, Abdollah; Fazel Zarandi, Mohammad Hossein; Soltanaghaei, Elahe

    2016-09-01

    Accidents involving falls and falling objects (group I) are highly frequent accidents in the construction industry. While being hit by a vehicle, electric shock, collapse in the excavation and fire or explosion accidents (group II) are much less frequent, they make up a considerable proportion of severe accidents. In this study, multiple-correspondence analysis, decision tree, ensembles of decision tree and association rules methods are employed to analyse a database of construction accidents throughout Iran between 2007 and 2011. The findings indicate that in group I, there is a significant correspondence among these variables: time of accident, place of accident, body part affected, final consequence of accident and lost workdays. Moreover, the frequency of accidents in the night shift is less than others, and the frequency of injury to the head, back, spine and limbs are more. In group II, the variables time of accident and body part affected are mostly related and the frequency of accidents among married and older workers is more than single and young workers. There was a higher frequency in the evening, night shifts and weekends. The results of this study are totally in line with the previous research.

  20. Evaluating the risk of death via the hematopoietic syndrome mode for prolonged exposure of nuclear workers to radiation delivered at very low rates.

    PubMed

    Scott, B R; Lyzlov, A F; Osovets, S V

    1998-05-01

    During a Phase-I effort, studies were planned to evaluate deterministic (nonstochastic) effects of chronic exposure of nuclear workers at the Mayak atomic complex in the former Soviet Union to relatively high levels (> 0.25 Gy) of ionizing radiation. The Mayak complex has been used, since the late 1940's, to produce plutonium for nuclear weapons. Workers at Site A of the complex were involved in plutonium breeding using nuclear reactors, and some were exposed to relatively large doses of gamma rays plus relatively small neutron doses. The Weibull normalized-dose model, which has been set up to evaluate the risk of specific deterministic effects of combined, continuous exposure of humans to alpha, beta, and gamma radiations, is here adapted for chronic exposure to gamma rays and neutrons during repeated 6-h work shifts--as occurred for some nuclear workers at Site A. Using the adapted model, key conclusions were reached that will facilitate a Phase-II study of deterministic effects among Mayak workers. These conclusions include the following: (1) neutron doses may be more important for Mayak workers than for Japanese A-bomb victims in Hiroshima and can be accounted for using an adjusted dose (which accounts for neutron relative biological effectiveness); (2) to account for dose-rate effects, normalized dose X (a dimensionless fraction of an LD50 or ED50) can be evaluated in terms of an adjusted dose; (3) nonlinear dose-response curves for the risk of death via the hematopoietic mode can be converted to linear dose-response curves (for low levels of risk) using a newly proposed dimensionless dose, D = X(V), in units of Oklad (where D is pronounced "deh"), and V is the shape parameter in the Weibull model; (4) for X < or = Xo, where Xo is the threshold normalized dose, D = 0; (5) unlike absorbed dose, the dose D can be averaged over different Mayak workers in order to calculate the average risk of death via the hematopoietic mode for the population exposed at Site A; and (6) the expected cases of death via the hematopoietic syndrome mode for Mayak workers chronically exposed during work shifts at Site A to gamma rays and neutrons can be predicted using ln(2)B M[D]; where B (pronounced "beh") is the number of workers at risk (criticality accident victims excluded); and M[D] is the average (mean) value of D (averaged over the worker population at risk, for Site A, for the time period considered). These results can be used to facilitate a Phase II study of deterministic radiation effects among Mayak workers chronically exposed to gamma rays and neutrons.

  1. Simulation of Hydrogen Distribution in Ignalina NPP ALS Compartments During BDBA

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Babilas, Egidijus; Urbonavicius, Egidijus; Rimkevicius, Sigitas

    2006-07-01

    Accident Localisation System (ALS) of Ignalina NPP is a 'pressure suppression' type confinement, which protects the population, employees and environment from the radiation hazards. According to the Safety Analysis Report for Ignalina NPP {approx}110 m{sup 3} of hydrogen is released to ALS compartments during the Maximum Design Basis Accident. However in case of beyond design basis accident, when the oxidation of zirconium starts, the amount of generated hydrogen could be significantly higher. If the volume concentration of hydrogen in the compartment reaches 4%, there is a possibility for a combustible mixture to appear. To prevent the possible hydrogen accumulation inmore » the ALS of the Ignalina NPP during an accident the H{sub 2} control system is installed. The results of the performed analysis derived the places of the possible H{sub 2} accumulation in the ALS compartments during the transient processes and assessed the mixture combustibility in these places for a beyond design basis accident scenario. Such analysis of H{sub 2} distribution in the ALS of Ignalina NPP in case of BDBA was not performed before. (authors)« less

  2. Key Parameters for Operator Diagnosis of BWR Plant Condition during a Severe Accident

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Clayton, Dwight A.; Poore, III, Willis P.

    2015-01-01

    The objective of this research is to examine the key information needed from nuclear power plant instrumentation to guide severe accident management and mitigation for boiling water reactor (BWR) designs (specifically, a BWR/4-Mark I), estimate environmental conditions that the instrumentation will experience during a severe accident, and identify potential gaps in existing instrumentation that may require further research and development. This report notes the key parameters that instrumentation needs to measure to help operators respond to severe accidents. A follow-up report will assess severe accident environmental conditions as estimated by severe accident simulation model analysis for a specific US BWR/4-Markmore » I plant for those instrumentation systems considered most important for accident management purposes.« less

  3. Impact of traffic congestion on road accidents: a spatial analysis of the M25 motorway in England.

    PubMed

    Wang, Chao; Quddus, Mohammed A; Ison, Stephen G

    2009-07-01

    Traffic congestion and road accidents are two external costs of transport and the reduction of their impacts is often one of the primary objectives for transport policy makers. The relationship between traffic congestion and road accidents however is not apparent and less studied. It is speculated that there may be an inverse relationship between traffic congestion and road accidents, and as such this poses a potential dilemma for transport policy makers. This study aims to explore the impact of traffic congestion on the frequency of road accidents using a spatial analysis approach, while controlling for other relevant factors that may affect road accidents. The M25 London orbital motorway, divided into 70 segments, was chosen to conduct this study and relevant data on road accidents, traffic and road characteristics were collected. A robust technique has been developed to map M25 accidents onto its segments. Since existing studies have often used a proxy to measure the level of congestion, this study has employed a precise congestion measurement. A series of Poisson based non-spatial (such as Poisson-lognormal and Poisson-gamma) and spatial (Poisson-lognormal with conditional autoregressive priors) models have been used to account for the effects of both heterogeneity and spatial correlation. The results suggest that traffic congestion has little or no impact on the frequency of road accidents on the M25 motorway. All other relevant factors have provided results consistent with existing studies.

  4. 'It was a freak accident': an analysis of the labelling of injury events in the US press.

    PubMed

    Smith, Katherine C; Girasek, Deborah C; Baker, Susan P; Manganello, Jennifer A; Bowman, Stephen M; Samuels, Alicia; Gielen, Andrea C

    2012-02-01

    Given that the news media shape our understanding of health issues, a study was undertaken to examine the use by the US media of the expression 'freak accident' in relation to injury events. This analysis is intended to contribute to the ongoing consideration of lay conceptualisation of injuries as 'accidents'. LexisNexis Academic was used to search three purposively selected US news sources (Associated Press, New York Times and Philadelphia Inquirer) for the expression 'freak accident' over 5 years (2005-9). Textual analysis included both structured and open coding. Coding included measures for who used the expression within the story, the nature of the injury event and the injured person(s) being reported upon, incorporation of prevention information within the story and finally a phenomenological consideration of the uses and meanings of the expression within the story context. Results The search yielded a dataset of 250 human injury stories incorporating the term 'freak accident'. Injuries sustained by professional athletes dominated coverage (61%). Fewer than 10% of stories provided a clear and explicit injury prevention message. Stories in which journalists employed the expression 'freak accident' were less likely to include prevention information than stories in which the expression was used by people quoted in the story. Journalists who frame injury events as freak accidents may be an appropriate focus for advocacy efforts. Effective prevention messages should be developed and disseminated to accompany injury reporting in order to educate and protect the public.

  5. STAMP-Based HRA Considering Causality Within a Sociotechnical System: A Case of Minuteman III Missile Accident.

    PubMed

    Rong, Hao; Tian, Jin

    2015-05-01

    The study contributes to human reliability analysis (HRA) by proposing a method that focuses more on human error causality within a sociotechnical system, illustrating its rationality and feasibility by using a case of the Minuteman (MM) III missile accident. Due to the complexity and dynamics within a sociotechnical system, previous analyses of accidents involving human and organizational factors clearly demonstrated that the methods using a sequential accident model are inadequate to analyze human error within a sociotechnical system. System-theoretic accident model and processes (STAMP) was used to develop a universal framework of human error causal analysis. To elaborate the causal relationships and demonstrate the dynamics of human error, system dynamics (SD) modeling was conducted based on the framework. A total of 41 contributing factors, categorized into four types of human error, were identified through the STAMP-based analysis. All factors are related to a broad view of sociotechnical systems, and more comprehensive than the causation presented in the accident investigation report issued officially. Recommendations regarding both technical and managerial improvement for a lower risk of the accident are proposed. The interests of an interdisciplinary approach provide complementary support between system safety and human factors. The integrated method based on STAMP and SD model contributes to HRA effectively. The proposed method will be beneficial to HRA, risk assessment, and control of the MM III operating process, as well as other sociotechnical systems. © 2014, Human Factors and Ergonomics Society.

  6. Effective environmental factors on geographical distribution of traffic accidents on pedestrians, downtown of Tehran City.

    PubMed

    Moradi, Ali; Rahmani, Khaled; Kavousi, Amir; Eshghabadi, Farshid; Nematollahi, Shahrzad; Zainni, Slahedyn; Soori, Hamid

    2018-02-20

    The aim of this study was to geographically analyse the traffic casualties in pedestrians in downtown of Tehran City. Study population consisted of pedestrians who had traffic injury accidents from April 2014 to March 2015 in Tehran City. Data were extracted from the offices of traffic police and municipality. For analysis of environmental factors and site of accidents, Ordinary Least Square (OLS) regression models and Geographically Weighted Regression (GWR) were used. All pedestrian accidents including 514 accidents were assessed in this study in which the site of accidents included arterial streets in 370 (71.9%) cases, collector streets in 133 cases (25.2%) and highways in 11 cases (2.1%). Geographical units of traffic accidents in pedestrians had statistically significant relationship with the number of bus stations, number of crossroads and recreational areas. Neighbourhoods close to markets are considered as the most dangerous places for injury in traffic accidents.

  7. The SAS4A/SASSYS-1 Safety Analysis Code System, Version 5

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fanning, T. H.; Brunett, A. J.; Sumner, T.

    The SAS4A/SASSYS-1 computer code is developed by Argonne National Laboratory for thermal, hydraulic, and neutronic analysis of power and flow transients in liquidmetal- cooled nuclear reactors (LMRs). SAS4A was developed to analyze severe core disruption accidents with coolant boiling and fuel melting and relocation, initiated by a very low probability coincidence of an accident precursor and failure of one or more safety systems. SASSYS-1, originally developed to address loss-of-decay-heat-removal accidents, has evolved into a tool for margin assessment in design basis accident (DBA) analysis and for consequence assessment in beyond-design-basis accident (BDBA) analysis. SAS4A contains detailed, mechanistic models of transientmore » thermal, hydraulic, neutronic, and mechanical phenomena to describe the response of the reactor core, its coolant, fuel elements, and structural members to accident conditions. The core channel models in SAS4A provide the capability to analyze the initial phase of core disruptive accidents, through coolant heat-up and boiling, fuel element failure, and fuel melting and relocation. Originally developed to analyze oxide fuel clad with stainless steel, the models in SAS4A have been extended and specialized to metallic fuel with advanced alloy cladding. SASSYS-1 provides the capability to perform a detailed thermal/hydraulic simulation of the primary and secondary sodium coolant circuits and the balance-ofplant steam/water circuit. These sodium and steam circuit models include component models for heat exchangers, pumps, valves, turbines, and condensers, and thermal/hydraulic models of pipes and plena. SASSYS-1 also contains a plant protection and control system modeling capability, which provides digital representations of reactor, pump, and valve controllers and their response to input signal changes.« less

  8. GIS-based accident location and analysis system (GIS-ALAS) : project report : phase I

    DOT National Transportation Integrated Search

    1998-04-06

    This report summarizes progress made in Phase I of the geographic information system (GIS) based Accident Location and Analysis System (GIS-ALAS). The GIS-ALAS project builds on PC-ALAS, a locationally-referenced highway crash database query system d...

  9. [Environmental, social, and roadway vulnerability in accidents involving transportation of hazardous products: a case study of the BR-101 highway between Osório and Torres in Rio Grande do Sul State, Brazil].

    PubMed

    Tinoco, Maria Auxiliadora Cannarozzo; Nodari, Christine Tessele; Pereira, Kimberllyn Rosa da Silva

    2016-09-19

    This study aimed to assess the environmental and social vulnerability and identify critical highway stretches for accidents involving transportation of hazardous products on the BR-101 highway between the cities of Osório and Torres in Rio Grande do Sul State, Brazil. The study's approach consisted of a multiple-criteria analysis combining highway safety analysis and environmental and social vulnerability analysis in the occurrence of accidents with hazardous products, plus cartographic analysis techniques. Thirty-eight kilometers of the highway showed high vulnerability, of which 8 kilometers with critical vulnerability, associated with bridges over rivers, water uptake points, a tunnel, environmental preservation areas, and an urban area. These stretches should be prioritized when developing action plans for accident mitigation and development of public policies for this highway. This proved to be an unprecedented approach when compared to existing studies and a potentially useful tool for decision-making in emergency operations.

  10. [Violence and accidents among older and younger adults: evidence from the Surveillance System for Violence and Accidents (VIVA), Brazil].

    PubMed

    Luz, Tatiana Chama Borges; Malta, Deborah Carvalho; Sá, Naíza Nayla Bandeira de; Silva, Marta Maria Alves da; Lima-Costa, Maria Fernanda

    2011-11-01

    Data from the Brazilian Surveillance System for Violence and Accidents (VIVA) in 2009 were used to examine socio-demographic characteristics, outcomes, and types of accidents and violence treated at 74 sentinel emergency services in 23 Brazilian State capitals and the Federal District. The analysis included 25,201 individuals aged > 20 years (10.1% > 60 years); 89.3% were victims of accidents and 11.9% victims of violence. Hospitalization was the outcome in 11.1% of cases. Compared to the general population, there were more men and non-white individuals among victims of accidents, and especially among victims of violence. As compared to younger adults (20-59 years), accidents and violence against elderly victims showed less association with alcohol, a higher proportion of domestic incidents, more falls and pedestrian accidents, and aggression by family members. Policies for the prevention of accidents and violence should consider the characteristics of these events in the older population.

  11. [Determinant factors and conduct in post-accident with biological material among pre-hospital professionals].

    PubMed

    Paiva, Maria Henriqueta Rocha Siqueira; Oliveira, Adriana Cristina

    2011-01-01

    This transversal study was carried out with a multiprofessional team in the pre-hospital care in Minas Gerais, Brazil. It aimed to estimate the incidence of occupational accidents by exposure to biological material and post-accidents conductsta. Descriptive analysis and logistic regression were used. Incidence of accidents was 19.8%: 39,1% perforating-cutting materials and 56.5% body fluids. Doctors (33.3%) and drivers (24.0%) were most involved. Inadequate subsequent measures were highly prevalent: no medical assessment (69.6%), no work accident communication issued (91.3%), no measures (52.2%) and no serological follow-up (52.2%). Variables associated with accidents were: age >31 years old (OR = 3,02; IC95%: 1,25 - 7,33; p = 0,014) and working in basic support units (OR = 5,36; IC95%: 1,51 19,08; p = 0,010). The implementation of post-accidents protocols is suggested in order to reduce accidents and under-notification, and increase post-accident follow-up.

  12. Analysis of Occupational Accident Fatalities and Injuries Among Male Group in Iran Between 2008 and 2012

    PubMed Central

    Alizadeh, Seyed Shamseddin; Mortazavi, Seyed Bagher; Sepehri, Mohammad Mehdi

    2015-01-01

    Background: Because of occupational accidents, permanent disabilities and deaths occur and economic and workday losses emerge. Objectives: The purpose of the present study was to investigate the factors responsible for occupational accidents occurred in Iran. Patients and Methods: The current study analyzed 1464 occupational accidents recorded by the Ministry of Labor and Social Affairs’ offices in Iran during 2008 - 2012. At first, general understanding of accidents was obtained using descriptive statistics. Afterwards, the chi-square test and Cramer’s V statistic (Vc) were used to determine the association between factors influencing the type of injury as occupational accident outcomes. Results: There was no significant association between marital status and time of day with the type of injury. However, activity sector, cause of accident, victim’s education, age of victim and victim’s experience were significantly associated with the type of injury. Conclusions: Successful accident prevention relies largely on knowledge about the causes of accidents. In any accident control activity, particularly in occupational accidents, correctly identifying high-risk groups and factors influencing accidents is the key to successful interventions. Results of this study can cause to increase accident awareness and enable workplace’s management to select and prioritize problem areas and safety system weakness in workplaces. PMID:26568848

  13. Deterministic multi-step rotation of magnetic single-domain state in Nickel nanodisks using multiferroic magnetoelastic coupling

    NASA Astrophysics Data System (ADS)

    Sohn, Hyunmin; Liang, Cheng-yen; Nowakowski, Mark E.; Hwang, Yongha; Han, Seungoh; Bokor, Jeffrey; Carman, Gregory P.; Candler, Robert N.

    2017-10-01

    We demonstrate deterministic multi-step rotation of a magnetic single-domain (SD) state in Nickel nanodisks using the multiferroic magnetoelastic effect. Ferromagnetic Nickel nanodisks are fabricated on a piezoelectric Lead Zirconate Titanate (PZT) substrate, surrounded by patterned electrodes. With the application of a voltage between opposing electrode pairs, we generate anisotropic in-plane strains that reshape the magnetic energy landscape of the Nickel disks, reorienting magnetization toward a new easy axis. By applying a series of voltages sequentially to adjacent electrode pairs, circulating in-plane anisotropic strains are applied to the Nickel disks, deterministically rotating a SD state in the Nickel disks by increments of 45°. The rotation of the SD state is numerically predicted by a fully-coupled micromagnetic/elastodynamic finite element analysis (FEA) model, and the predictions are experimentally verified with magnetic force microscopy (MFM). This experimental result will provide a new pathway to develop energy efficient magnetic manipulation techniques at the nanoscale.

  14. Delay compensation in integrated communication and control systems. I - Conceptual development and analysis

    NASA Technical Reports Server (NTRS)

    Luck, Rogelio; Ray, Asok

    1990-01-01

    A procedure for compensating for the effects of distributed network-induced delays in integrated communication and control systems (ICCS) is proposed. The problem of analyzing systems with time-varying and possibly stochastic delays could be circumvented by use of a deterministic observer which is designed to perform under certain restrictive but realistic assumptions. The proposed delay-compensation algorithm is based on a deterministic state estimator and a linear state-variable-feedback control law. The deterministic observer can be replaced by a stochastic observer without any structural modifications of the delay compensation algorithm. However, if a feedforward-feedback control law is chosen instead of the state-variable feedback control law, the observer must be modified as a conventional nondelayed system would be. Under these circumstances, the delay compensation algorithm would be accordingly changed. The separation principle of the classical Luenberger observer holds true for the proposed delay compensator. The algorithm is suitable for ICCS in advanced aircraft, spacecraft, manufacturing automation, and chemical process applications.

  15. Analysis of deterministic swapping of photonic and atomic states through single-photon Raman interaction

    NASA Astrophysics Data System (ADS)

    Rosenblum, Serge; Borne, Adrien; Dayan, Barak

    2017-03-01

    The long-standing goal of deterministic quantum interactions between single photons and single atoms was recently realized in various experiments. Among these, an appealing demonstration relied on single-photon Raman interaction (SPRINT) in a three-level atom coupled to a single-mode waveguide. In essence, the interference-based process of SPRINT deterministically swaps the qubits encoded in a single photon and a single atom, without the need for additional control pulses. It can also be harnessed to construct passive entangling quantum gates, and can therefore form the basis for scalable quantum networks in which communication between the nodes is carried out only by single-photon pulses. Here we present an analytical and numerical study of SPRINT, characterizing its limitations and defining parameters for its optimal operation. Specifically, we study the effect of losses, imperfect polarization, and the presence of multiple excited states. In all cases we discuss strategies for restoring the operation of SPRINT.

  16. Space Radiation Transport Methods Development

    NASA Technical Reports Server (NTRS)

    Wilson, J. W.; Tripathi, R. K.; Qualls, G. D.; Cucinotta, F. A.; Prael, R. E.; Norbury, J. W.; Heinbockel, J. H.; Tweed, J.

    2002-01-01

    Improved spacecraft shield design requires early entry of radiation constraints into the design process to maximize performance and minimize costs. As a result, we have been investigating high-speed computational procedures to allow shield analysis from the preliminary design concepts to the final design. In particular, we will discuss the progress towards a full three-dimensional and computationally efficient deterministic code for which the current HZETRN evaluates the lowest order asymptotic term. HZETRN is the first deterministic solution to the Boltzmann equation allowing field mapping within the International Space Station (ISS) in tens of minutes using standard Finite Element Method (FEM) geometry common to engineering design practice enabling development of integrated multidisciplinary design optimization methods. A single ray trace in ISS FEM geometry requires 14 milliseconds and severely limits application of Monte Carlo methods to such engineering models. A potential means of improving the Monte Carlo efficiency in coupling to spacecraft geometry is given in terms of reconfigurable computing and could be utilized in the final design as verification of the deterministic method optimized design.

  17. Non-Deterministic Dynamic Instability of Composite Shells

    NASA Technical Reports Server (NTRS)

    Chamis, Christos C.; Abumeri, Galib H.

    2004-01-01

    A computationally effective method is described to evaluate the non-deterministic dynamic instability (probabilistic dynamic buckling) of thin composite shells. The method is a judicious combination of available computer codes for finite element, composite mechanics, and probabilistic structural analysis. The solution method is incrementally updated Lagrangian. It is illustrated by applying it to thin composite cylindrical shell subjected to dynamic loads. Both deterministic and probabilistic buckling loads are evaluated to demonstrate the effectiveness of the method. A universal plot is obtained for the specific shell that can be used to approximate buckling loads for different load rates and different probability levels. Results from this plot show that the faster the rate, the higher the buckling load and the shorter the time. The lower the probability, the lower is the buckling load for a specific time. Probabilistic sensitivity results show that the ply thickness, the fiber volume ratio and the fiber longitudinal modulus, dynamic load and loading rate are the dominant uncertainties, in that order.

  18. Review of U.S. Army Unmanned Aerial Systems Accident Reports: Analysis of Human Error Contributions

    DTIC Science & Technology

    2018-03-20

    USAARL Report No. 2018-08 Review of U.S. Army Unmanned Aerial Systems Accident Reports: Analysis of Human Error Contributions By Kathryn A...3 Statistical Analysis Approach ..............................................................................................3 Results...1 Introduction The success of unmanned aerial systems (UAS) operations relies upon a variety of factors, including, but not limited to

  19. [The medical organizational aspects of decreasing of preventable mortality in the case of traffic accident in municipal district].

    PubMed

    Voloshina, L V; Plutnitskiĭ, A N

    2010-01-01

    The article deals with the results of the study of such actual issue as decreasing of preventable mortality in the case of traffic accident in municipal district. The analysis was based on the mortality statistical data and the expertise of causes of lethal outcomes of traffic accidents. The results are used to develop the measures of improving the organization and quality of medical care of victims of road accident on the pre-hospital and hospital stages on the level of municipal health care to decrease the human losses caused by traffic accident.

  20. The analysis of influence of individual and environmental factors on 2-wheeled users' injuries.

    PubMed

    Marković, Nenad; Pešić, Dalibor R; Antić, Boris; Vujanić, Milan

    2016-08-17

    Powered 2-wheeled motor vehicles (PTWs) are one of the most vulnerable categories of road users. Bearing that fact in mind, we have researched the effects of individual and environmental factors on the severity and type of injuries of PTW users. The aim was to recognize the circumstances that cause these accidents and take some preventive actions that would improve the level of road safety for PTWs. In the period from 2001 to 2010, an analysis of 139 road accidents involving PTWs was made by the Faculty of Transport and Traffic Engineering in Belgrade. The effects of both individual (age, gender, etc.) and environmental factors (place of an accident, time of day, etc.) on the cause of accidents and severity and type of injuries of PTWs are reported in this article. Analyses of these effects were conducted using logistic regression, chi-square tests, and Pearson's correlation. Factors such as categories of road users, pavement conditions, place of accident, age, and time of day have a statistically significant effect on PTW injuries, whereas other factors (gender, road type; that is, straight or curvy) do not. The article also defines the interdependence of the occurrence of particular injuries at certain speeds. The results show that if PTW users died of a head injury, these were usually concurrent with chest injuries, injuries to internal organs, and limb injuries. It has been shown that there is a high degree of influence of individual factors on the occurrence of accidents involving 2-wheelers (PTWs/bicycles) but with no statistically significant relation. Establishing the existence of such conditionalities enables identifying and defining factors that have an impact on the occurrence of traffic accidents involving bicyclists or PTWs. Such a link between individual factors and the occurrence of accidents makes it possible for system managers to take appropriate actions aimed at certain categories of 2-wheelers in order to reduce casualties in a particular area. The analysis showed that most of the road factors do not have a statistically significant effect on either category of 2-wheeler. Namely, the logistic regression analysis showed that there is a statistically significant effect of the place of accident on the occurrence of accidents involving bicyclists.

  1. DOE Office of Scientific and Technical Information (OSTI.GOV)

    Panayotov, Dobromir; Poitevin, Yves; Grief, Andrew

    'Fusion for Energy' (F4E) is designing, developing, and implementing the European Helium-Cooled Lead-Lithium (HCLL) and Helium-Cooled Pebble-Bed (HCPB) Test Blanket Systems (TBSs) for ITER (Nuclear Facility INB-174). Safety demonstration is an essential element for the integration of these TBSs into ITER and accident analysis is one of its critical components. A systematic approach to accident analysis has been developed under the F4E contract on TBS safety analyses. F4E technical requirements, together with Amec Foster Wheeler and INL efforts, have resulted in a comprehensive methodology for fusion breeding blanket accident analysis that addresses the specificity of the breeding blanket designs, materials,more » and phenomena while remaining consistent with the approach already applied to ITER accident analyses. Furthermore, the methodology phases are illustrated in the paper by its application to the EU HCLL TBS using both MELCOR and RELAP5 codes.« less

  2. A Human Factors Analysis and Classification System (HFACS) Examination of Commercial Vessel Accidents

    DTIC Science & Technology

    2012-09-01

    Naval Operations before the Congress on FY2013 Department of Navy posture. Heinrich , H . W. (1941). Industrial accident prevention : A scientific...Theory The core of the Domino Theory, developed by Herbert W. Heinrich who studied industrial safety in the early 1900s, is that accidents are a result...chain of events resulting in an accident . Heinrich likened the dominos to unsafe conditions or unsafe acts, where their subsequent removal prevents a

  3. [Analysis of accidents in selected occupations in the Szczecin shipyard S.A. in the years 1989-93].

    PubMed

    Kośmider, K; Niezgoda, A; Dadej, R; Myślak, M

    1997-01-01

    In a five-year follow-up study (1989-93), 1317 work-related accidents and their relation to occupational exposure among male workers employed at the Szczecin Shipyard were analysed. The highest rates of accidents were found among welders, fitters, electrical mechanics and platers. The role of the age, duration of employment, type of the job performed and its contribution to the rate and pattern of accidents, were also investigated.

  4. Economic situation and occupational accidents in Poland: 2002-2014 panel data regional study.

    PubMed

    Łyszczarz, Błażej; Nojszewska, Ewelina

    2018-01-07

    Occupational accidents constitute a substantial health and economic burden for societies around the world and a variety of factors determine the frequency of accidents at work. The aim of this paper is to investigate the relationship between the economic situation and the rate of occupational accidents in Poland. The analysis comprised data for 66 Polish sub-regions taken from the Central Statistical Office's Local Data Bank. The regression analysis with panel data for period 2002-2014 was applied to identify the relationships involved. Four measures of accidents were used: the rates of total occupational accidents, accidents among men and women separately as well as days of incapacity to work due to accidents at work per employee. Four alternative measures assessed the economic situation: gross domestic product (GDP) per capita, average remuneration, the unemployment rate and number of dwelling permits. The confounding variables included were: employment in hazardous conditions and the size of enterprises. The results of the regression estimates show that the number of occupational accidents in Poland exhibits procyclical behavior, which means that more accidents are observed during the times of economic expansion. Stronger relationships were observed in the equations explaining men's accident rates as well as total rates. A weaker and not always statistically significant impact of economic situation was identified for women's accident rates and days of incapacity to work. The results have important implications for occupational health and safety actions. In the periods of higher work intensity employers should focus on appropriate training and supervision of inexperienced workers as well as on ensuring enough time for already experienced employees to recuperate. In terms of public health actions, policy makers should focus on scrutinizing working conditions, educating employers and counteracting possible discrimination of injured employees. Int J Occup Med Environ Health 2018;31(2):151-164. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

  5. Factors associated with non-return to work in the severely injured victims 3 years after a road accident: A prospective study.

    PubMed

    Pélissier, C; Fort, E; Fontana, L; Charbotel, B; Hours, M

    2017-09-01

    Road accidents may impact victims' physical and/or mental health and socio-occupational life, particularly the capacity to return to work. The purpose of our study is to assess modifiable medical and socio-occupational factors of non-return to work in the severely injured 3 years after a road accident. Among1,168 road accidents casualties in the Rhône administrative Département of France followed for five years, 141 of the 222 severely injured (Maximal Abbreviated Injury Scale ≥ 3) aged more than 16 years who were in work at the time of the accident, reported whether they had returned to work in the 3 years following the accident. The subgroups of those who had (n=113) and had not returned to work (n=28) were compared for socio-occupational (gender, age, educational level, marital status, socio-occupational group) accident-related medical factors (type of road user, type of journey, responsibility in the accident, initial care) and post-accident medical factors (pain intensity, post-traumatic stress disorder, physical sequelae, quality of life) by using standardized tools. Severity of initial head, face and lower-limb injury, intense persistent pain, post-traumatic stress disorder, poor self-assessed quality of life and health status at 3 years were associated with non-return to work on univariate analysis. On multivariate analysis, severity of initial head and lower-limb injury, intense persistent pain at 3 years and post-traumatic stress disorder were significantly associated with non-return to work 3 years following severe road-accident injury. Post-traumatic stress disorder and chronic pain were essential modifiable medical determinants of non-return to work in the severely injured after a road accident: early adapted management could promote return to work in the severely injured. Improve early adapted treatment of pain and PTSD in the rehabilitation team should help the severely injured return to work following a road accident. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Review of Hybrid (Deterministic/Monte Carlo) Radiation Transport Methods, Codes, and Applications at Oak Ridge National Laboratory

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wagner, John C; Peplow, Douglas E.; Mosher, Scott W

    2011-01-01

    This paper provides a review of the hybrid (Monte Carlo/deterministic) radiation transport methods and codes used at the Oak Ridge National Laboratory and examples of their application for increasing the efficiency of real-world, fixed-source Monte Carlo analyses. The two principal hybrid methods are (1) Consistent Adjoint Driven Importance Sampling (CADIS) for optimization of a localized detector (tally) region (e.g., flux, dose, or reaction rate at a particular location) and (2) Forward Weighted CADIS (FW-CADIS) for optimizing distributions (e.g., mesh tallies over all or part of the problem space) or multiple localized detector regions (e.g., simultaneous optimization of two or moremore » localized tally regions). The two methods have been implemented and automated in both the MAVRIC sequence of SCALE 6 and ADVANTG, a code that works with the MCNP code. As implemented, the methods utilize the results of approximate, fast-running 3-D discrete ordinates transport calculations (with the Denovo code) to generate consistent space- and energy-dependent source and transport (weight windows) biasing parameters. These methods and codes have been applied to many relevant and challenging problems, including calculations of PWR ex-core thermal detector response, dose rates throughout an entire PWR facility, site boundary dose from arrays of commercial spent fuel storage casks, radiation fields for criticality accident alarm system placement, and detector response for special nuclear material detection scenarios and nuclear well-logging tools. Substantial computational speed-ups, generally O(102-4), have been realized for all applications to date. This paper provides a brief review of the methods, their implementation, results of their application, and current development activities, as well as a considerable list of references for readers seeking more information about the methods and/or their applications.« less

  7. Spectral Analysis of the Effects of Daylight Saving Time on Motor Vehicle Fatal Traffic Accidents

    DOT National Transportation Integrated Search

    1977-04-01

    This report shows that Daylight Saving Time (DST) reduces the number of persons killed in motor vehicle fatal traffic accidents by about one percent. This estimate is based on a spectral (Fourier) analysis of these fatalities which utilizes a filteri...

  8. General Methodology Combining Engineering Optimization of Primary HVAC and R Plants with Decision Analysis Methods--Part II: Uncertainty and Decision Analysis

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Jiang, Wei; Reddy, T. A.; Gurian, Patrick

    2007-01-31

    A companion paper to Jiang and Reddy that presents a general and computationally efficient methodology for dyanmic scheduling and optimal control of complex primary HVAC&R plants using a deterministic engineering optimization approach.

  9. Quality evaluation of official accident reports conducted by Labour Authorities in Andalusia (Spain).

    PubMed

    Salguero-Caparros, Francisco; Suarez-Cebador, Manuel; Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos

    2018-01-01

    A public accident investigation is carried out when the consequences of the incident are significant or the accident has occurred in unusual circumstances. We evaluated the quality of the official accident investigations being conducted by Safety Specialists of the Labour Authorities in Andalusia. To achieve this objective, we analysed 98 occupational accident investigations conducted by the Labour Authorities in Andalusia in the last quarter of 2014. Various phases in the accident investigation process were examined, such as the use of the Eurostat variables within European Statistics on Accidents at Work (ESAW), detection of causes, determination of preventive measures, cost analysis of the accidents, identification of noncompliance with legal requirements or the investigation method used. The results of this study show that 77% of the official occupational accident investigation reports analysed were conducted in accordance with all the quality criteria recommended in the literature. To enhance glogal learning, and optimize allocation of resources, we propose the development of a harmonized European model for the public investigation of occupational accidents. Further it would be advisable to create a common classification and coding system for the causes of accidents for all European Union Member States.

  10. Accident data study of concrete construction companies' similarities and differences between qualified and non-qualified workers in Spain.

    PubMed

    López-Arquillos, Antonio; Rubio-Romero, Juan Carlos; Gibb, Alistair

    2015-01-01

    The aim of this paper is to discuss findings from an analysis of accidents in concrete construction companies in Spain and to compare the accident rates of qualified and non-qualified workers. A total of 125,021 accidents between 2003 and 2008 involving both blue-collar and white-collar workers were analysed, comparing the variables of occupation, age, company staff, length of service, location of the accident, together with the severity of the accidents. Results showed that lack of experience in the first month is more significant in non-qualified workers and experienced supervisors and that head injuries are more likely to lead to fatalities. The most remarkable similarity was that fatal accidents to and from the worksite are a problem common to both groups of workers.

  11. Structural Deterministic Safety Factors Selection Criteria and Verification

    NASA Technical Reports Server (NTRS)

    Verderaime, V.

    1992-01-01

    Though current deterministic safety factors are arbitrarily and unaccountably specified, its ratio is rooted in resistive and applied stress probability distributions. This study approached the deterministic method from a probabilistic concept leading to a more systematic and coherent philosophy and criterion for designing more uniform and reliable high-performance structures. The deterministic method was noted to consist of three safety factors: a standard deviation multiplier of the applied stress distribution; a K-factor for the A- or B-basis material ultimate stress; and the conventional safety factor to ensure that the applied stress does not operate in the inelastic zone of metallic materials. The conventional safety factor is specifically defined as the ratio of ultimate-to-yield stresses. A deterministic safety index of the combined safety factors was derived from which the corresponding reliability proved the deterministic method is not reliability sensitive. The bases for selecting safety factors are presented and verification requirements are discussed. The suggested deterministic approach is applicable to all NASA, DOD, and commercial high-performance structures under static stresses.

  12. The Fukushima Daiichi Accident Study Information Portal

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Shawn St. Germain; Curtis Smith; David Schwieder

    This paper presents a description of The Fukushima Daiichi Accident Study Information Portal. The Information Portal was created by the Idaho National Laboratory as part of joint NRC and DOE project to assess the severe accident modeling capability of the MELCOR analysis code. The Fukushima Daiichi Accident Study Information Portal was created to collect, store, retrieve and validate information and data for use in reconstructing the Fukushima Daiichi accident. In addition to supporting the MELCOR simulations, the Portal will be the main DOE repository for all data, studies and reports related to the accident at the Fukushima Daiichi nuclear powermore » station. The data is stored in a secured (password protected and encrypted) repository that is searchable and accessible to researchers at diverse locations.« less

  13. [Factors associated with work-related accidents in the informal commercial sector].

    PubMed

    Rios, Marcela Andrade; Nery, Adriana Alves; Rios, Polianna Alves Andrade; Casotti, Cezar Augusto; Cardoso, Jefferson Paixão

    2015-06-01

    This study aimed to estimate the incidence of non-fatal work-related accidents in the informal commercial sector and analyze associated socio-demographic, occupational, workplace, and health factors, in a cross-sectional survey of 434 workers in the business district of Jequié, Bahia State, Brazil, in 2013. Logistic regression was used to assess factors associated with accidents. Incidence of accidents in the previous 12 months was estimated at 32.3%, and multivariate analysis showed higher odds of accidents in male sex workers (OR = 1.61), young individuals (OR = 4.62), meat or poultry workers (OR = 9.55), and workers performing heavy physical work (OR = 1.71). The results show the need for public policies to prevent accidents in the informal commercial sector.

  14. Are schools safer for children than public places?

    PubMed Central

    Maitra, A K; Sweeney, G

    1996-01-01

    OBJECTIVE--To investigate the frequency and severity of accidents to children in schools. METHODS--Retrospective analysis of accidents occurring in school over a six month period and resulting in attendance at an accident and emergency department. Comparison was made with accidents occurring in public places, RESULTS--During the study period there were 127 school and 251 public place accidents causing fractures or dislocations requiring hospital treatment in 3-16 year old children; 22.4% (127/567) of all injuries at school resulted in fractures or dislocations, as opposed to 20.8% (251/1197) of those sustained in public places. CONCLUSIONS--Injuries at school are a cause for concern as they occur in a supervised environment and this should be the target of accident prevention measures. PMID:8733659

  15. Study on the evaluation method for fault displacement based on characterized source model

    NASA Astrophysics Data System (ADS)

    Tonagi, M.; Takahama, T.; Matsumoto, Y.; Inoue, N.; Irikura, K.; Dalguer, L. A.

    2016-12-01

    In IAEA Specific Safety Guide (SSG) 9 describes that probabilistic methods for evaluating fault displacement should be used if no sufficient basis is provided to decide conclusively that the fault is not capable by using the deterministic methodology. In addition, International Seismic Safety Centre compiles as ANNEX to realize seismic hazard for nuclear facilities described in SSG-9 and shows the utility of the deterministic and probabilistic evaluation methods for fault displacement. In Japan, it is required that important nuclear facilities should be established on ground where fault displacement will not arise when earthquakes occur in the future. Under these situations, based on requirements, we need develop evaluation methods for fault displacement to enhance safety in nuclear facilities. We are studying deterministic and probabilistic methods with tentative analyses using observed records such as surface fault displacement and near-fault strong ground motions of inland crustal earthquake which fault displacements arose. In this study, we introduce the concept of evaluation methods for fault displacement. After that, we show parts of tentative analysis results for deterministic method as follows: (1) For the 1999 Chi-Chi earthquake, referring slip distribution estimated by waveform inversion, we construct a characterized source model (Miyake et al., 2003, BSSA) which can explain observed near-fault broad band strong ground motions. (2) Referring a characterized source model constructed in (1), we study an evaluation method for surface fault displacement using hybrid method, which combines particle method and distinct element method. At last, we suggest one of the deterministic method to evaluate fault displacement based on characterized source model. This research was part of the 2015 research project `Development of evaluating method for fault displacement` by the Secretariat of Nuclear Regulation Authority (S/NRA), Japan.

  16. Relative Roles of Deterministic and Stochastic Processes in Driving the Vertical Distribution of Bacterial Communities in a Permafrost Core from the Qinghai-Tibet Plateau, China.

    PubMed

    Hu, Weigang; Zhang, Qi; Tian, Tian; Li, Dingyao; Cheng, Gang; Mu, Jing; Wu, Qingbai; Niu, Fujun; Stegen, James C; An, Lizhe; Feng, Huyuan

    2015-01-01

    Understanding the processes that influence the structure of biotic communities is one of the major ecological topics, and both stochastic and deterministic processes are expected to be at work simultaneously in most communities. Here, we investigated the vertical distribution patterns of bacterial communities in a 10-m-long soil core taken within permafrost of the Qinghai-Tibet Plateau. To get a better understanding of the forces that govern these patterns, we examined the diversity and structure of bacterial communities, and the change in community composition along the vertical distance (spatial turnover) from both taxonomic and phylogenetic perspectives. Measures of taxonomic and phylogenetic beta diversity revealed that bacterial community composition changed continuously along the soil core, and showed a vertical distance-decay relationship. Multiple stepwise regression analysis suggested that bacterial alpha diversity and phylogenetic structure were strongly correlated with soil conductivity and pH but weakly correlated with depth. There was evidence that deterministic and stochastic processes collectively drived bacterial vertically-structured pattern. Bacterial communities in five soil horizons (two originated from the active layer and three from permafrost) of the permafrost core were phylogenetically random, indicator of stochastic processes. However, we found a stronger effect of deterministic processes related to soil pH, conductivity, and organic carbon content that were structuring the bacterial communities. We therefore conclude that the vertical distribution of bacterial communities was governed primarily by deterministic ecological selection, although stochastic processes were also at work. Furthermore, the strong impact of environmental conditions (for example, soil physicochemical parameters and seasonal freeze-thaw cycles) on these communities underlines the sensitivity of permafrost microorganisms to climate change and potentially subsequent permafrost thaw.

  17. Relative Roles of Deterministic and Stochastic Processes in Driving the Vertical Distribution of Bacterial Communities in a Permafrost Core from the Qinghai-Tibet Plateau, China

    PubMed Central

    Tian, Tian; Li, Dingyao; Cheng, Gang; Mu, Jing; Wu, Qingbai; Niu, Fujun; Stegen, James C.; An, Lizhe; Feng, Huyuan

    2015-01-01

    Understanding the processes that influence the structure of biotic communities is one of the major ecological topics, and both stochastic and deterministic processes are expected to be at work simultaneously in most communities. Here, we investigated the vertical distribution patterns of bacterial communities in a 10-m-long soil core taken within permafrost of the Qinghai-Tibet Plateau. To get a better understanding of the forces that govern these patterns, we examined the diversity and structure of bacterial communities, and the change in community composition along the vertical distance (spatial turnover) from both taxonomic and phylogenetic perspectives. Measures of taxonomic and phylogenetic beta diversity revealed that bacterial community composition changed continuously along the soil core, and showed a vertical distance-decay relationship. Multiple stepwise regression analysis suggested that bacterial alpha diversity and phylogenetic structure were strongly correlated with soil conductivity and pH but weakly correlated with depth. There was evidence that deterministic and stochastic processes collectively drived bacterial vertically-structured pattern. Bacterial communities in five soil horizons (two originated from the active layer and three from permafrost) of the permafrost core were phylogenetically random, indicator of stochastic processes. However, we found a stronger effect of deterministic processes related to soil pH, conductivity, and organic carbon content that were structuring the bacterial communities. We therefore conclude that the vertical distribution of bacterial communities was governed primarily by deterministic ecological selection, although stochastic processes were also at work. Furthermore, the strong impact of environmental conditions (for example, soil physicochemical parameters and seasonal freeze-thaw cycles) on these communities underlines the sensitivity of permafrost microorganisms to climate change and potentially subsequent permafrost thaw. PMID:26699734

  18. Canister Storage Building (CSB) Hazard Analysis Report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    POWERS, T.B.

    2000-03-16

    This report describes the methodology used in conducting the Canister Storage Building (CSB) Hazard Analysis to support the final CSB Safety Analysis Report and documents the results. This report describes the methodology used in conducting the Canister Storage Building (CSB) hazard analysis to support the CSB final safety analysis report (FSAR) and documents the results. The hazard analysis process identified hazardous conditions and material-at-risk, determined causes for potential accidents, identified preventive and mitigative features, and qualitatively estimated the frequencies and consequences of specific occurrences. The hazard analysis was performed by a team of cognizant CSB operations and design personnel, safetymore » analysts familiar with the CSB, and technical experts in specialty areas. The material included in this report documents the final state of a nearly two-year long process. Attachment A provides two lists of hazard analysis team members and describes the background and experience of each. The first list is a complete list of the hazard analysis team members that have been involved over the two-year long process. The second list is a subset of the first list and consists of those hazard analysis team members that reviewed and agreed to the final hazard analysis documentation. The material included in this report documents the final state of a nearly two-year long process involving formal facilitated group sessions and independent hazard and accident analysis work. The hazard analysis process led to the selection of candidate accidents for further quantitative analysis. New information relative to the hazards, discovered during the accident analysis, was incorporated into the hazard analysis data in order to compile a complete profile of facility hazards. Through this process, the results of the hazard and accident analyses led directly to the identification of safety structures, systems, and components, technical safety requirements, and other controls required to protect the public, workers, and environment.« less

  19. Assessment and prediction of road accident injuries trend using time-series models in Kurdistan.

    PubMed

    Parvareh, Maryam; Karimi, Asrin; Rezaei, Satar; Woldemichael, Abraha; Nili, Sairan; Nouri, Bijan; Nasab, Nader Esmail

    2018-01-01

    Road traffic accidents are commonly encountered incidents that can cause high-intensity injuries to the victims and have direct impacts on the members of the society. Iran has one of the highest incident rates of road traffic accidents. The objective of this study was to model the patterns of road traffic accidents leading to injury in Kurdistan province, Iran. A time-series analysis was conducted to characterize and predict the frequency of road traffic accidents that lead to injury in Kurdistan province. The injuries were categorized into three separate groups which were related to the car occupants, motorcyclists and pedestrian road traffic accident injuries. The Box-Jenkins time-series analysis was used to model the injury observations applying autoregressive integrated moving average (ARIMA) and seasonal autoregressive integrated moving average (SARIMA) from March 2009 to February 2015 and to predict the accidents up to 24 months later (February 2017). The analysis was carried out using R-3.4.2 statistical software package. A total of 5199 pedestrians, 9015 motorcyclists, and 28,906 car occupants' accidents were observed. The mean (SD) number of car occupant, motorcyclist and pedestrian accident injuries observed were 401.01 (SD 32.78), 123.70 (SD 30.18) and 71.19 (SD 17.92) per year, respectively. The best models for the pattern of car occupant, motorcyclist, and pedestrian injuries were the ARIMA (1, 0, 0), SARIMA (1, 0, 2) (1, 0, 0) 12 , and SARIMA (1, 1, 1) (0, 0, 1) 12 , respectively. The motorcyclist and pedestrian injuries showed a seasonal pattern and the peak was during summer (August). The minimum frequency for the motorcyclist and pedestrian injuries were observed during the late autumn and early winter (December and January). Our findings revealed that the observed motorcyclist and pedestrian injuries had a seasonal pattern that was explained by air temperature changes overtime. These findings call the need for close monitoring of the accidents during the high-risk periods in order to control and decrease the rate of the injuries.

  20. The Stochastic Multi-strain Dengue Model: Analysis of the Dynamics

    NASA Astrophysics Data System (ADS)

    Aguiar, Maíra; Stollenwerk, Nico; Kooi, Bob W.

    2011-09-01

    Dengue dynamics is well known to be particularly complex with large fluctuations of disease incidences. An epidemic multi-strain model motivated by dengue fever epidemiology shows deterministic chaos in wide parameter regions. The addition of seasonal forcing, mimicking the vectorial dynamics, and a low import of infected individuals, which is realistic in the dynamics of infectious diseases epidemics show complex dynamics and qualitatively a good agreement between empirical DHF monitoring data and the obtained model simulation. The addition of noise can explain the fluctuations observed in the empirical data and for large enough population size, the stochastic system can be well described by the deterministic skeleton.

  1. Finite-size effects and switching times for Moran process with mutation.

    PubMed

    DeVille, Lee; Galiardi, Meghan

    2017-04-01

    We consider the Moran process with two populations competing under an iterated Prisoner's Dilemma in the presence of mutation, and concentrate on the case where there are multiple evolutionarily stable strategies. We perform a complete bifurcation analysis of the deterministic system which arises in the infinite population size. We also study the Master equation and obtain asymptotics for the invariant distribution and metastable switching times for the stochastic process in the case of large but finite population. We also show that the stochastic system has asymmetries in the form of a skew for parameter values where the deterministic limit is symmetric.

  2. 78 FR 60321 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses and Combined Licenses...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-01

    ... sample selection. A steam generator tube rupture (SGTR) event is one of the design basis accidents that... in the design basis accident analysis. The proposed change will not cause the consequences of a SGTR... changes to the plant design basis or postulated accidents resulting from potential tube degradation. The...

  3. Total systems design analysis of high performance structures

    NASA Technical Reports Server (NTRS)

    Verderaime, V.

    1993-01-01

    Designer-control parameters were identified at interdiscipline interfaces to optimize structural systems performance and downstream development and operations with reliability and least life-cycle cost. Interface tasks and iterations are tracked through a matrix of performance disciplines integration versus manufacturing, verification, and operations interactions for a total system design analysis. Performance integration tasks include shapes, sizes, environments, and materials. Integrity integrating tasks are reliability and recurring structural costs. Significant interface designer control parameters were noted as shapes, dimensions, probability range factors, and cost. Structural failure concept is presented, and first-order reliability and deterministic methods, benefits, and limitations are discussed. A deterministic reliability technique combining benefits of both is proposed for static structures which is also timely and economically verifiable. Though launch vehicle environments were primarily considered, the system design process is applicable to any surface system using its own unique filed environments.

  4. Elasto-limited plastic analysis of structures for probabilistic conditions

    NASA Astrophysics Data System (ADS)

    Movahedi Rad, M.

    2018-06-01

    With applying plastic analysis and design methods, significant saving in material can be obtained. However, as a result of this benefit excessive plastic deformations and large residual displacements might develop, which in turn might lead to unserviceability and collapse of the structure. In this study, for deterministic problem the residual deformation of structures is limited by considering a constraint on the complementary strain energy of the residual forces. For probabilistic problem the constraint for the complementary strain energy of the residual forces is given randomly and critical stresses updated during the iteration. Limit curves are presented for the plastic limit load factors. The results show that these constraints have significant effects on the load factors. The formulations of the deterministic and probabilistic problems lead to mathematical programming which are solved by the use of nonlinear algorithm.

  5. Development of a Probabilistic Component Mode Synthesis Method for the Analysis of Non-Deterministic Substructures

    NASA Technical Reports Server (NTRS)

    Brown, Andrew M.; Ferri, Aldo A.

    1995-01-01

    Standard methods of structural dynamic analysis assume that the structural characteristics are deterministic. Recognizing that these characteristics are actually statistical in nature, researchers have recently developed a variety of methods that use this information to determine probabilities of a desired response characteristic, such as natural frequency, without using expensive Monte Carlo simulations. One of the problems in these methods is correctly identifying the statistical properties of primitive variables such as geometry, stiffness, and mass. This paper presents a method where the measured dynamic properties of substructures are used instead as the random variables. The residual flexibility method of component mode synthesis is combined with the probabilistic methods to determine the cumulative distribution function of the system eigenvalues. A simple cantilever beam test problem is presented that illustrates the theory.

  6. Cost-Utility Analysis of Telemonitoring Interventions for Patients with Chronic Obstructive Pulmonary Disease (COPD) in Germany.

    PubMed

    Hofer, Florian; Achelrod, Dmitrij; Stargardt, Tom

    2016-12-01

    Chronic obstructive pulmonary disease (COPD) poses major challenges for health care systems. Previous studies suggest that telemonitoring could be effective in preventing hospitalisations and hence reduce costs. The aim was to evaluate whether telemonitoring interventions for COPD are cost-effective from the perspective of German statutory sickness funds. A cost-utility analysis was conducted using a combination of a Markov model and a decision tree. Telemonitoring as add-on to standard treatment was compared with standard treatment alone. The model consisted of four transition stages to account for COPD severity, and a terminal stage for death. Within each cycle, the frequency of exacerbations as well as outcomes for 2015 costs and quality adjusted life years (QALYs) for each stage were calculated. Values for input parameters were taken from the literature. Deterministic and probabilistic sensitivity analyses were conducted. In the base case, telemonitoring led to an increase in incremental costs (€866 per patient) but also in incremental QALYs (0.05 per patient). The incremental cost-effectiveness ratio (ICER) was thus €17,410 per QALY gained. A deterministic sensitivity analysis showed that hospitalisation rate and costs for telemonitoring equipment greatly affected results. The probabilistic ICER averaged €34,432 per QALY (95 % confidence interval 12,161-56,703). We provide evidence that telemonitoring may be cost-effective in Germany from a payer's point of view. This holds even after deterministic and probabilistic sensitivity analyses.

  7. Scaling and design analyses of a scaled-down, high-temperature test facility for experimental investigation of the initial stages of a VHTR air-ingress accident

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Arcilesi, David J.; Ham, Tae Kyu; Kim, In Hun

    2015-07-01

    A critical event in the safety analysis of the very high-temperature gas-cooled reactor (VHTR) is an air-ingress accident. This accident is initiated, in its worst case scenario, by a double-ended guillotine break of the coaxial cross vessel, which leads to a rapid reactor vessel depressurization. In a VHTR, the reactor vessel is located within a reactor cavity that is filled with air during normal operating conditions. Following the vessel depressurization, the dominant mode of ingress of an air–helium mixture into the reactor vessel will either be molecular diffusion or density-driven stratified flow. The mode of ingress is hypothesized to dependmore » largely on the break conditions of the cross vessel. Since the time scales of these two ingress phenomena differ by orders of magnitude, it is imperative to understand under which conditions each of these mechanisms will dominate in the air ingress process. Computer models have been developed to analyze this type of accident scenario. There are, however, limited experimental data available to understand the phenomenology of the air-ingress accident and to validate these models. Therefore, there is a need to design and construct a scaled-down experimental test facility to simulate the air-ingress accident scenarios and to collect experimental data. The current paper focuses on the analyses performed for the design and operation of a 1/8th geometric scale (by height and diameter), high-temperature test facility. A geometric scaling analysis for the VHTR, a time scale analysis of the air-ingress phenomenon, a transient depressurization analysis of the reactor vessel, a hydraulic similarity analysis of the test facility, a heat transfer characterization of the hot plenum, a power scaling analysis for the reactor system, and a design analysis of the containment vessel are discussed.« less

  8. Probabilistic Analysis Techniques Applied to Complex Spacecraft Power System Modeling

    NASA Technical Reports Server (NTRS)

    Hojnicki, Jeffrey S.; Rusick, Jeffrey J.

    2005-01-01

    Electric power system performance predictions are critical to spacecraft, such as the International Space Station (ISS), to ensure that sufficient power is available to support all the spacecraft s power needs. In the case of the ISS power system, analyses to date have been deterministic, meaning that each analysis produces a single-valued result for power capability because of the complexity and large size of the model. As a result, the deterministic ISS analyses did not account for the sensitivity of the power capability to uncertainties in model input variables. Over the last 10 years, the NASA Glenn Research Center has developed advanced, computationally fast, probabilistic analysis techniques and successfully applied them to large (thousands of nodes) complex structural analysis models. These same techniques were recently applied to large, complex ISS power system models. This new application enables probabilistic power analyses that account for input uncertainties and produce results that include variations caused by these uncertainties. Specifically, N&R Engineering, under contract to NASA, integrated these advanced probabilistic techniques with Glenn s internationally recognized ISS power system model, System Power Analysis for Capability Evaluation (SPACE).

  9. Dual ant colony operational modal analysis parameter estimation method

    NASA Astrophysics Data System (ADS)

    Sitarz, Piotr; Powałka, Bartosz

    2018-01-01

    Operational Modal Analysis (OMA) is a common technique used to examine the dynamic properties of a system. Contrary to experimental modal analysis, the input signal is generated in object ambient environment. Operational modal analysis mainly aims at determining the number of pole pairs and at estimating modal parameters. Many methods are used for parameter identification. Some methods operate in time while others in frequency domain. The former use correlation functions, the latter - spectral density functions. However, while some methods require the user to select poles from a stabilisation diagram, others try to automate the selection process. Dual ant colony operational modal analysis parameter estimation method (DAC-OMA) presents a new approach to the problem, avoiding issues involved in the stabilisation diagram. The presented algorithm is fully automated. It uses deterministic methods to define the interval of estimated parameters, thus reducing the problem to optimisation task which is conducted with dedicated software based on ant colony optimisation algorithm. The combination of deterministic methods restricting parameter intervals and artificial intelligence yields very good results, also for closely spaced modes and significantly varied mode shapes within one measurement point.

  10. The Analysis of the Contribution of Human Factors to the In-Flight Loss of Control Accidents

    NASA Technical Reports Server (NTRS)

    Ancel, Ersin; Shih, Ann T.

    2012-01-01

    In-flight loss of control (LOC) is currently the leading cause of fatal accidents based on various commercial aircraft accident statistics. As the Next Generation Air Transportation System (NextGen) emerges, new contributing factors leading to LOC are anticipated. The NASA Aviation Safety Program (AvSP), along with other aviation agencies and communities are actively developing safety products to mitigate the LOC risk. This paper discusses the approach used to construct a generic integrated LOC accident framework (LOCAF) model based on a detailed review of LOC accidents over the past two decades. The LOCAF model is comprised of causal factors from the domain of human factors, aircraft system component failures, and atmospheric environment. The multiple interdependent causal factors are expressed in an Object-Oriented Bayesian belief network. In addition to predicting the likelihood of LOC accident occurrence, the system-level integrated LOCAF model is able to evaluate the impact of new safety technology products developed in AvSP. This provides valuable information to decision makers in strategizing NASA's aviation safety technology portfolio. The focus of this paper is on the analysis of human causal factors in the model, including the contributions from flight crew and maintenance workers. The Human Factors Analysis and Classification System (HFACS) taxonomy was used to develop human related causal factors. The preliminary results from the baseline LOCAF model are also presented.

  11. An aftermath analysis of the 2014 coal mine accident in Soma, Turkey: Use of risk performance indicators based on historical experience.

    PubMed

    Spada, Matteo; Burgherr, Peter

    2016-02-01

    On the 13th of May 2014 a fire related incident in the Soma coal mine in Turkey caused 301 fatalities and more than 80 injuries. This has been the largest coal mine accident in Turkey, and in the OECD country group, so far. This study investigated if such a disastrous event should be expected, in a statistical sense, based on historical observations. For this purpose, PSI's ENSAD database is used to extract accident data for the period 1970-2014. Four different cases are analyzed, i.e., OECD, OECD w/o Turkey, Turkey and USA. Analysis of temporal trends for annual numbers of accidents and fatalities indicated a non-significant decreasing tendency for OECD and OECD w/o Turkey and a significant one for USA, whereas for Turkey both measures showed an increase over time. The expectation analysis revealed clearly that an event with the consequences of the Soma accident is rather unlikely for OECD, OECD w/o Turkey and USA. In contrast, such a severe accident has a substantially higher expectation for Turkey, i.e. it cannot be considered an extremely rare event, based on historical experience. This indicates a need for improved safety measures and stricter regulations in the Turkish coal mining sector in order to get closer to the rest of OECD. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Pressing the Approach: A NASA Study of 19 Recent Accidents Yields a New Perspective on Pilot Error

    NASA Technical Reports Server (NTRS)

    Berman, Benjamin A.; Dismukes, R. Key

    2007-01-01

    This article begins with a review of two sample airplane accidents that were caused by pilot error. The analysis of these and 17 other accidents suggested that almost all experienced pilot operating in the same environment in which the accident crews were operating and knowing only what the accident crews knew at each moment of the flight, would be vulnerable to making a similar decision and similar errors. Whether a particular crew in a given situation makes errors depends on somewhat random interaction of factors. Two themes that seem to be prevalent in these cases are: Plan Continuation Bias, and Snowballing Workload.

  13. Strategies for dealing with resistance to recommendations from accident investigations.

    PubMed

    Lundberg, Jonas; Rollenhagen, Carl; Hollnagel, Erik; Rankin, Amy

    2012-03-01

    Accident investigation reports usually lead to a set of recommendations for change. These recommendations are, however, sometimes resisted for reasons such as various aspects of ethics and power. When accident investigators are aware of this, they use several strategies to overcome the resistance. This paper describes strategies for dealing with four different types of resistance to change. The strategies were derived from qualitative analysis of 25 interviews with Swedish accident investigators from seven application domains. The main contribution of the paper is a better understanding of effective strategies for achieving change associated with accident investigation. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. Impacts of Considering Climate Variability on Investment Decisions in Ethiopia

    NASA Astrophysics Data System (ADS)

    Strzepek, K.; Block, P.; Rosegrant, M.; Diao, X.

    2005-12-01

    In Ethiopia, climate extremes, inducing droughts or floods, are not unusual. Monitoring the effects of these extremes, and climate variability in general, is critical for economic prediction and assessment of the country's future welfare. The focus of this study involves adding climate variability to a deterministic, mean climate-driven agro-economic model, in an attempt to understand its effects and degree of influence on general economic prediction indicators for Ethiopia. Four simulations are examined, including a baseline simulation and three investment strategies: simulations of irrigation investment, roads investment, and a combination investment of both irrigation and roads. The deterministic model is transformed into a stochastic model by dynamically adding year-to-year climate variability through climate-yield factors. Nine sets of actual, historic, variable climate data are individually assembled and implemented into the 12-year stochastic model simulation, producing an ensemble of economic prediction indicators. This ensemble allows for a probabilistic approach to planning and policy making, allowing decision makers to consider risk. The economic indicators from the deterministic and stochastic approaches, including rates of return to investments, are significantly different. The predictions of the deterministic model appreciably overestimate the future welfare of Ethiopia; the predictions of the stochastic model, utilizing actual climate data, tend to give a better semblance of what may be expected. Inclusion of climate variability is vital for proper analysis of the predictor values from this agro-economic model.

  15. Probabilistic vs. deterministic fiber tracking and the influence of different seed regions to delineate cerebellar-thalamic fibers in deep brain stimulation.

    PubMed

    Schlaier, Juergen R; Beer, Anton L; Faltermeier, Rupert; Fellner, Claudia; Steib, Kathrin; Lange, Max; Greenlee, Mark W; Brawanski, Alexander T; Anthofer, Judith M

    2017-06-01

    This study compared tractography approaches for identifying cerebellar-thalamic fiber bundles relevant to planning target sites for deep brain stimulation (DBS). In particular, probabilistic and deterministic tracking of the dentate-rubro-thalamic tract (DRTT) and differences between the spatial courses of the DRTT and the cerebello-thalamo-cortical (CTC) tract were compared. Six patients with movement disorders were examined by magnetic resonance imaging (MRI), including two sets of diffusion-weighted images (12 and 64 directions). Probabilistic and deterministic tractography was applied on each diffusion-weighted dataset to delineate the DRTT. Results were compared with regard to their sensitivity in revealing the DRTT and additional fiber tracts and processing time. Two sets of regions-of-interests (ROIs) guided deterministic tractography of the DRTT or the CTC, respectively. Tract distances to an atlas-based reference target were compared. Probabilistic fiber tracking with 64 orientations detected the DRTT in all twelve hemispheres. Deterministic tracking detected the DRTT in nine (12 directions) and in only two (64 directions) hemispheres. Probabilistic tracking was more sensitive in detecting additional fibers (e.g. ansa lenticularis and medial forebrain bundle) than deterministic tracking. Probabilistic tracking lasted substantially longer than deterministic. Deterministic tracking was more sensitive in detecting the CTC than the DRTT. CTC tracts were located adjacent but consistently more posterior to DRTT tracts. These results suggest that probabilistic tracking is more sensitive and robust in detecting the DRTT but harder to implement than deterministic approaches. Although sensitivity of deterministic tracking is higher for the CTC than the DRTT, targets for DBS based on these tracts likely differ. © 2017 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

  16. Learning from Trending, Precursor Analysis, and System Failures

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Youngblood, R. W.; Duffey, R. B.

    2015-11-01

    Models of reliability growth relate current system unreliability to currently accumulated experience. But “experience” comes in different forms. Looking back after a major accident, one is sometimes able to identify previous events or measurable performance trends that were, in some sense, signaling the potential for that major accident: potential that could have been recognized and acted upon, but was not recognized until the accident occurred. This could be a previously unrecognized cause of accidents, or underestimation of the likelihood that a recognized potential cause would actually operate. Despite improvements in the state of practice of modeling of risk and reliability,more » operational experience still has a great deal to teach us, and work has been going on in several industries to try to do a better job of learning from experience before major accidents occur. It is not enough to say that we should review operating experience; there is too much “experience” for such general advice to be considered practical. The paper discusses the following: 1. The challenge of deciding what to focus on in analysis of operating experience. 2. Comparing what different models of learning and reliability growth imply about trending and precursor analysis.« less

  17. Decision-problem state analysis methodology

    NASA Technical Reports Server (NTRS)

    Dieterly, D. L.

    1980-01-01

    A methodology for analyzing a decision-problem state is presented. The methodology is based on the analysis of an incident in terms of the set of decision-problem conditions encountered. By decomposing the events that preceded an unwanted outcome, such as an accident, into the set of decision-problem conditions that were resolved, a more comprehensive understanding is possible. All human-error accidents are not caused by faulty decision-problem resolutions, but it appears to be one of the major areas of accidents cited in the literature. A three-phase methodology is presented which accommodates a wide spectrum of events. It allows for a systems content analysis of the available data to establish: (1) the resolutions made, (2) alternatives not considered, (3) resolutions missed, and (4) possible conditions not considered. The product is a map of the decision-problem conditions that were encountered as well as a projected, assumed set of conditions that should have been considered. The application of this methodology introduces a systematic approach to decomposing the events that transpired prior to the accident. The initial emphasis is on decision and problem resolution. The technique allows for a standardized method of accident into a scenario which may used for review or the development of a training simulation.

  18. Spatio-temporal patterns of hazards and their use in risk assessment and mitigation. Case study of road accidents in Romania

    NASA Astrophysics Data System (ADS)

    Catalin Stanga, Iulian

    2013-04-01

    Road accidents are among the leading causes of death in many world countries, partly as an inherent consequence of the increasing mobility of today society. The World Health Organization estimates that 1.3 million people died in road accidents in 2011, which means 186 deaths per million. The tragic picture is completed by millions of peoples experiencing different physical injuries or by the enormous social and economic costs that these events imply. Romania has one of the most unsafe road networks within the European Union, with annual averages of 9400 accidents, 8300 injuries and almost 2680 fatalities (2007-2012). An average of 141 death per million is more than twice the average fatality rate in European Union (about 60 death per million). Other specific indicators (accidents or fatalities reported to the road length, vehicle fleet size, driving license owners or adult population etc.) are even worst in the same European context. Road accidents are caused by a complex series of factors, some of them being a relatively constant premise, while others act as catalyzing factors or triggering agent: road features and quality, vehicle technical state, weather conditions, human related factors etc. All these lead to a complex equation with too many unknown variables, making almost impossible a probabilistic approach. However, the high concentration of accidents in a region or in some road sectors is caused by the existence of a specific context, created by factors with permanent or repetitive character, and leads to the idea of a spatial autocorrelation between locations of different adjoining accident. In the same way, the increasing frequency of road accidents and of their causes repeatability in different periods of the year would allow to identify those black timeframes with higher incidence of road accidents. Identifying and analyzing the road blackspots (hotspots) and black zones would help to improve road safety by acting against the common causes that create the spatial or temporal clustering of crash accidents. Since the 1990's, Geographical Informational Systems (GIS) became a very important tool for traffic and road safety management, allowing not only the spatial and multifactorial analysis, but also graphical and non-graphical outputs. The current paper presents an accessible GIS methodology to study the spatio-temporal pattern of injury related road accidents, to identify the high density accidents zones, to make a cluster analysis, to create multicriterial typologies, to identify spatial and temporal similarities and to explain them. In this purpose, a Geographical Information System was created, allowing a complex analysis that involves not only the events, but also a large set of interrelated and spatially linked attributes. The GIS includes the accidents as georeferenced point elements with a spatially linked attribute database: identification information (date, location details); accident type; main, secondary and aggravating causes; data about driver; vehicle information; consequences (damages, injured peoples and fatalities). Each attribute has its own number code that allows both the statistical analysis and the spatial interrogation. The database includes those road accidents that led to physical injuries and loss of human lives between 2007 and 2012 and the spatial analysis was realized using TNTmips 7.3 software facilities. Data aggregation and processing allowed creating the spatial pattern of injury related road accidents through Kernel density estimation at three different levels (national - Romania; county level - Iasi County; local level - Iasi town). Spider graphs were used to create the temporal pattern or road accidents at three levels (daily, weekly and monthly) directly related to their causes. Moreover the spatial and temporal database relates the natural hazards (glazed frost, fog, and blizzard) with the human made ones, giving the opportunity to evaluate the nature of uncertainties in risk assessment. At the end, this paper provides a clustering methodology based on several environmental indicators intended to classify the spatial and temporal hotspots of road traffic insecurity. The results are a useful guide for planners and decision makers in developing effective road safety strategies and measures.

  19. How safe are HEMS-programmes in Germany? A retrospective analysis.

    PubMed

    Thies, Karl-Christian; Sep, Daan; Derksen, Remon

    2006-03-01

    Recent accidents with helicopter emergency medical service (HEMS) aircraft raise the question how safe HEMS in Germany is and how accidents could be prevented. We surveyed all German HEMS-programmes and reviewed the data of the German Aviation Authority regarding accidents with HEMS. An average German HEMS-programme encounters one accident leading to at least severe damage or loss of the helicopter in 26 operating years, one accident resulting in casualties in 65 operating years and one fatal accident in 111 operating years. The major causes of accidents were obstacle strikes during landing at the scene. Flying in bad weather conditions and lack of discipline were other factors contributing to HEMS-accidents. HEMS-safety could be improved by special training programmes for pilots and HEMS-crewmembers to address the factors listed above. Safety training for doctors is recommended but we did not find support for the notion of changing the doctor's legal position of a passenger to a HEMS-crewmember.

  20. Occupational accidents aboard merchant ships

    PubMed Central

    Hansen, H; Nielsen, D; Frydenberg, M

    2002-01-01

    Objectives: To investigate the frequency, circumstances, and causes of occupational accidents aboard merchant ships in international trade, and to identify risk factors for the occurrence of occupational accidents as well as dangerous working situations where possible preventive measures may be initiated. Methods: The study is a historical follow up on occupational accidents among crew aboard Danish merchant ships in the period 1993–7. Data were extracted from the Danish Maritime Authority and insurance data. Exact data on time at risk were available. Results: A total of 1993 accidents were identified during a total of 31 140 years at sea. Among these, 209 accidents resulted in permanent disability of 5% or more, and 27 were fatal. The mean risk of having an occupational accident was 6.4/100 years at sea and the risk of an accident causing a permanent disability of 5% or more was 0.67/100 years aboard. Relative risks for notified accidents and accidents causing permanent disability of 5% or more were calculated in a multivariate analysis including ship type, occupation, age, time on board, change of ship since last employment period, and nationality. Foreigners had a considerably lower recorded rate of accidents than Danish citizens. Age was a major risk factor for accidents causing permanent disability. Change of ship and the first period aboard a particular ship were identified as risk factors. Walking from one place to another aboard the ship caused serious accidents. The most serious accidents happened on deck. Conclusions: It was possible to clearly identify work situations and specific risk factors for accidents aboard merchant ships. Most accidents happened while performing daily routine duties. Preventive measures should focus on workplace instructions for all important functions aboard and also on the prevention of accidents caused by walking around aboard the ship. PMID:11850550

  1. Safety regulations, firm size, and the risk of accidents in E&P operations on the Gulf of Mexico outer continental shelf

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Iledare, O.O.; Pulsipher, A.G.; Baumann, R.H.

    1996-12-31

    The current expanded role of smaller independent oil producers in the OCS has led to concern about the possibility of increased risk of accidents in E&P operations on the Gulf of Mexico OCS. In addition, questions have been posed concerning the effects of the Minerals Management Service`s (MMS) safety regulations and inspection program, firm size, and industry practices on the risk of accidents in E&P operations on the Gulf of Mexico OCS. The specific purposes of the study reported in this paper were to ascertain (1) whether any empirical justification exists for the widespread concern that an increase in independentsmore » relative share of E&P operations in the Gulf OCS region will be detrimental to safety, and (2) whether MMS policies and safety programs have reduced the frequency or severity of accidents on the OCS. Our statistical and descriptive analyses of data on accidents from MMS provide no statistical evidence to support the apprehension that an expanded role for independents in E&P activity constitutes any major threat to safety on the OCS. Further, the results of our econometrics analysis confirm the expectation that the more effective MMS inspectors are at detecting incidents of noncompliance the lower the rate of accidents on the OCS is, ceteris paribus. In addition the results indicate that the variability in platform exposure years--cumulative age of operating platform--in comparison to other factors explains a significant portion of the variation in accidents per operating platform. That is, the platform aging process provides more opportunity for accidents than any other contributing factors. Our econometrics analysis also suggests that, if the other factors contributing to offshore accidents are held constant, the responsiveness of accident rate to drilling activity is inelastic while the response of accident rate to production activity levels is elastic.« less

  2. Analysis of traffic accidents in Romania, 2009.

    PubMed

    Călinoiu, Geovana; Minca, Dana Galieta; Furtunescu, Florentina Ligia

    2012-01-01

    This paper aimed to underline the main consequences of traffic accidents in Romania 2009 and their associated causes or circumstances. We identified some problematic geographic areas, some critical months or moments of the day and also the most frequent causes; all these should become targets for the future planning. The current analysis provides some priority criteria for public health interventions. So, the future national road safety strategy should be in line with the EU objectives, but also with the national priorities. Romania is far away from the average EU target for 2010 of halving the death by traffic accidents registered in 2001. To describe the circumstances and the consequences related to traffic accidents registered in Romania, for the year 2009. An ecological study was conducted. The traffic accidents circumstances were analyzed in terms of magnitude, geographic space, time and cause. The consequences were analyzed as affected people and damaged cars. A total of 28,627 traffic accidents were registered in Romania during the year 2009. 2,796 people were killed and 27,968 were hospitalized and 42,443 cars were damaged. 3 of 4 accidents were caused by violations on behalf of the car drivers. Most common violations in car drivers were excess of speed and priority violations (52.4%). Among the pedestrians, 7 of 10 accidents were caused by illegal crossing. A higher number of accidents occurred during the summer months and during the evening hours (from 5.00 pm till 8.00 pm). The traffic accidents represent a real public health problem in Romania and a serious burden for the health system. The gap between Romania and the other EU member states needs to be diminished in the next decade. In this purpose, the future national road safety strategy should be in line with the EU objectives, but also with the national priorities. Research is needed to understand the causes and the socio-economical impact of traffic accidents and to define appropriate national objectives.

  3. Causes of Coal Mine Accidents in the World and Turkey.

    PubMed

    Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

    2015-04-01

    Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents.

  4. Causes of Coal Mine Accidents in the World and Turkey

    PubMed Central

    Küçük, Filiz Çağla Uyanusta; Ilgaz, Aslıhan

    2015-01-01

    Occupational accidents and occupational diseases are common in the mining sector in Turkey and throughout the world. The most common causes of accidents in coal mining are firedamp and dust explosions, landslips, mine fires, and technical failures related to transport and mechanization. An analysis of occupational accidents in the consideration of social and economic factors will let understand the real causes behind these accidents, which are said to happen inevitably due to technical deficiencies or failures. Irregular working conditions, based on profit maximization and cost minimization, are related to strategic operational preferences and public policies. Proving that accidents in mines, where occupational health and safety measures are not implemented and inspections are not done properly or at all, are caused by the fact that production is imposed to be carried out in the fastest, cheapest, and most profitable way will allow us to take steps to prevent further mine accidents. PMID:29404108

  5. The special severity of occupational accidents in the afternoon: "the lunch effect".

    PubMed

    Camino López, Miguel A; Fontaneda, Ignacio; González Alcántara, Oscar J; Ritzel, Dale O

    2011-05-01

    The severity of occupational accidents suffered by construction workers at different hours of the day is analyzed in this study. It may be seen that the interval of time between 13:00 and 17:00 has incomprehensibly high rates of severe and fatal accidents in comparison with any other. We associate this higher accident rate with what we have termed the "lunch effect". We studied 10,239,303 labor accidents in Spain over the period 1990-2002. The relationships between potential risk factors for occupational accidents around lunch in Spain, especially alcohol consumption are studied, using two methods: analysis of national archival data of 2,155,954 occupational accidents suffered by workers in the construction sector over the period 1990-2002 and a survey study. This study also seeks to contribute the opinions of the workers themselves regarding the causes that might explain this situation. Copyright © 2010 Elsevier Ltd. All rights reserved.

  6. Predictions of structural integrity of steam generator tubes under normal operating, accident, an severe accident conditions

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Majumdar, S.

    1997-02-01

    Available models for predicting failure of flawed and unflawed steam generator tubes under normal operating, accident, and severe accident conditions are reviewed. Tests conducted in the past, though limited, tended to show that the earlier flow-stress model for part-through-wall axial cracks overestimated the damaging influence of deep cracks. This observation was confirmed by further tests at high temperatures, as well as by finite-element analysis. A modified correlation for deep cracks can correct this shortcoming of the model. Recent tests have shown that lateral restraint can significantly increase the failure pressure of tubes with unsymmetrical circumferential cracks. This observation was confirmedmore » by finite-element analysis. The rate-independent flow stress models that are successful at low temperatures cannot predict the rate-sensitive failure behavior of steam generator tubes at high temperatures. Therefore, a creep rupture model for predicting failure was developed and validated by tests under various temperature and pressure loadings that can occur during postulated severe accidents.« less

  7. Causes of accidents in terrain parks: an exploratory factor analysis of recreational freestylers' views.

    PubMed

    Carús, Luis

    2014-03-01

    This study examines ski and snowboard terrain park users' views on aspects associated with accidents by identifying and assessing variables that may influence the occurrence of accidents and the resulting injuries. The research was conducted in a major resort in the Spanish Pyrenees, using information gathered from freestyle skiers and snowboarders aged 6 or older. To identify interrelationships among variables and to group the variables belonging to unified concepts, an exploratory factor analysis was performed using varimax rotation. The results revealed 5 factors that grouped the measured variables that may influence the occurrence of accidents while freestyling in terrain parks. The park features, conditions of the activity, and the user's personal conditions were found to have the most substantial influence on the freestylers' perceptions. Variables identified as components of the main factors of accident risk in terrain parks should be incorporated into resort management communication and policies. © 2013 Wilderness Medical Society Published by Wilderness Medical Society All rights reserved.

  8. Fission product transport analysis in a loss of decay heat removal accident at Browns Ferry

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Wichner, R.P.; Weber, C.F.; Hodge, S.A.

    1984-01-01

    This paper summarizes an analysis of the movement of noble gases, iodine, and cesium fission products within the Mark-I containment BWR reactor system represented by Browns Ferry Unit 1 during a postulated accident sequence initiated by a loss of decay heat removal (DHR) capability following a scram. The event analysis showed that this accident could be brought under control by various means, but the sequence with no operator action ultimately leads to containment (drywell) failure followed by loss of water from the reactor vessel, core degradation due to overheating, and reactor vessel failure with attendant movement of core debris ontomore » the drywell floor.« less

  9. Differences in Characteristics of Aviation Accidents During 1993-2012 Based on Aircraft Type

    NASA Technical Reports Server (NTRS)

    Evans, Joni K.

    2015-01-01

    Civilian aircraft are available in a variety of sizes, engine types, construction materials and instrumentation complexity. For the analysis reported here, eleven aircraft categories were developed based mostly on aircraft size and engine type, and these categories were applied to twenty consecutive years of civil aviation accidents. Differences in various factors were examined among these aircraft types, including accident severity, pilot characteristics and accident occurrence categories. In general, regional jets and very light sport aircraft had the lowest rates of adverse outcomes (injuries, fatal accidents, aircraft destruction, major accidents), while aircraft with twin (piston) engines or with a single (piston) engine and retractable landing gear carried the highest incidence of adverse outcomes. The accident categories of abnormal runway contact, runway excursions and non-powerplant system/component failures occur frequently within all but two or three aircraft types. In contrast, ground collisions, loss of control - on ground/water and powerplant system/component failure occur frequently within only one or two aircraft types. Although accidents in larger aircraft tend to have less severe outcomes, adverse outcome rates also differ among accident categories. It may be that the type of accident has as much or more influence on the outcome as the type of aircraft.

  10. The situation of hazardous chemical accidents in China between 2000 and 2006.

    PubMed

    Duan, Weili; Chen, Guohua; Ye, Qing; Chen, Qingguang

    2011-02-28

    From the aspects of the total quantity of accidents, regional inequality, enterprises scale and environmental pollution accidents, this study makes an analysis of hazardous chemical accidents in China for the period spanning from 2000 to 2006. The following results are obtained: firstly, there were lots of accidents and fatalities in hazardous chemical business, i.e., the number of casualty accidents fluctuated between 200 and 600/year, the number of fatality fluctuated between 220 and 1100/year. Secondly, the accident rate in developed southeast coastal areas, e.g., Guangdong, Zhejiang and Jiangsu, was far higher than that in the northwest regions, e.g., Xizang, Xinjiang, and Qinghai. Thirdly, nearly 80% of dangerous chemical accidents had occurred in small and medium-sized enterprises (SMEs). Finally, various sudden environmental pollution accidents resulted from hazardous chemicals were frequent in recent years, causing a huge damage to human and property. Then, based on the readjustment of economic structure in the last decades, the development status of Occupational Health and Safety (OHS) in SMEs and other factors, the paper explores the main causes, which offers valuable insight into measures that should be taken to reduce hazardous chemical accidents. Copyright © 2010 Elsevier B.V. All rights reserved.

  11. Estimation of fatality and injury risk by means of in-depth fatal accident investigation data.

    PubMed

    Yannis, George; Papadimitriou, Eleonora; Dupont, Emmanuelle; Martensen, Heike

    2010-10-01

    In this article the factors affecting fatality and injury risk of road users involved in fatal accidents are analyzed by means of in-depth accident investigation data, with emphasis on parameters not extensively explored in previous research. A fatal accident investigation (FAI) database is used, which includes intermediate-level in-depth data for a harmonized representative sample of 1300 fatal accidents in 7 European countries. The FAI database offers improved potential for analysis, because it includes information on a number of variables that are seldom available, complete, or accurately recorded in road accident databases. However, the fact that only fatal accidents are examined requires for methodological adjustments, namely, the correction for two types of effects on a road user's baseline risk: "accident size" effects, and "relative vulnerability" effects. Fatality and injury risk can be then modeled through multilevel logistic regression models, which account for the hierarchical dependences of the road accident process. The results show that the baseline fatality risk of road users involved in fatal accidents decreases with accident size and increases with the vulnerability of the road user. On the contrary, accident size increases nonfatal injury risk of road users involved in fatal accidents. Other significant effects on fatality and injury risk in fatal accidents include road user age, vehicle type, speed limit, the chain of accident events, vehicle maneuver, and safety equipment. In particular, the presence and use of safety equipment such as seat belt, antilock braking system (ABS), and electronic stability program (ESP) are protection factors for car occupants, especially for those seated at the front seats. Although ABS and ESP systems are typically associated with positive effects on accident occurrence, the results of this research revealed significant related effects on accident severity as well. Moreover, accident consequences are more severe when the most harmful event of the accident occurs later within the accident chain.

  12. Lessons Learned from the Accident at the Fukushima Dai-ichi Nuclear Power Plant-More than Basic Knowledge: Education and its Effects Improve the Preparedness and Response to Radiation Emergency.

    PubMed

    Hachiya, Misao; Akashi, Makoto

    2016-09-01

    A huge earthquake struck the northeast coast of the main island of Japan on 11 March 2011 triggering an extremely large tsunami to hit the area. The earthquake and tsunami caused serious damage to the Fukushima nuclear power plants (NPPs) of Tokyo Electric Power Company (TEPCO), resulting in large amounts of radioactive materials being released into the environment. The major nuclides released were (131)I, (134)Cs and (137)Cs. The deposition of these radioactive materials on land resulted in a high ambient dose of radiation around the NPPs, especially within a 20-km radius. Dose assessments based on behavior survey and ambient dose rates revealed that external doses to most residents were lower than 5 mSv, with the maximum dose being 25 mSv. It was fortunate that no workers from the NPPs required treatment from the viewpoint of deterministic effects of radiation. However, a lack of exact knowledge of radiation and its effects prevented the system for medical care and transportation of contaminated personnel from functioning. After the accident, demands or requests for training courses have been increasing. We have learned from the response to this disaster that basic knowledge of radiation and its effects is extremely important for not only professionals such as health care providers but also for other professionals including teachers. © World Health Organisation 2016. All rights reserved. The World Health Organization has granted Oxford University Press permission for the reproduction of this article.

  13. Requirements Analysis for the Army Safety Management Information System (ASMIS)

    DTIC Science & Technology

    1989-03-01

    8217_>’ Telephone Number « .. PNL-6819 Limited Distribution Requirements Analysis for the Army Safety Management Information System (ASMIS) Final...PNL-6819 REQUIREMENTS ANALYSIS FOR THE ARMY SAFETY MANAGEMENT INFORMATION SYSTEM (ASMIS) FINAL REPORT J. S. Littlefield A. L. Corrigan March...accidents. This accident data is available under the Army Safety Management Information System (ASMIS) which is an umbrella for many databases

  14. Methodological guidelines for developing accident modification functions.

    PubMed

    Elvik, Rune

    2015-07-01

    This paper proposes methodological guidelines for developing accident modification functions. An accident modification function is a mathematical function describing systematic variation in the effects of road safety measures. The paper describes ten guidelines. An example is given of how to use the guidelines. The importance of exploratory analysis and an iterative approach in developing accident modification functions is stressed. The example shows that strict compliance with all the guidelines may be difficult, but represents a level of stringency that should be strived for. Currently the main limitations in developing accident modification functions are the small number of good evaluation studies and the often huge variation in estimates of effect. It is therefore still not possible to develop accident modification functions for very many road safety measures. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Driver Performance Problems of Intercity Bus Public Transportation Safety in Indonesia

    NASA Astrophysics Data System (ADS)

    Suraji, A.; Harnen, S.; Wicaksono, A.; Djakfar, L.

    2017-11-01

    The risk of an inter-city bus public accident can be influenced by various factors such as the driver’s performance. Therefore, knowing the various influential factors related to driver’s performance is very necessary as an effort to realize road traffic safety. This study aims to determine the factors that fall on the accident associated with the driver’s performance and make mathematical modeling factors that affect the accident. Methods of data retrieval were obtained from NTSC secondary data. The data was processed by identifying factors that cause the accident. Furthermore data processing and analysis used the PCA method to obtain mathematical modeling of factors influencing the inter-city bus accidents. The results showed that the main factors that cause accidents are health, discipline, and driver competence.

  16. [The meaning of accidents with biological material to nursing professionals].

    PubMed

    Magagnini, Maristela Aparecida Magri; Rocha, Suelen Alves; Ayres, Jairo Aparecido

    2011-06-01

    The aim of this study is to understand what meaning work accidents with exposure to biological material has to nurses. This is an exploratory study with a qualitative approach, and it used Bardin's content analysis. 87 accidents with biological material occurred in the period between 2001 and 2006; among them, eight were seropositive for Hepatitis B and C and HIV/AIDS. An interview with guiding questions was used to collect data. When inquiring these professionals about the meaning of these accidents, four categories emerged: risk situation, danger perception, fatality, and feelings. Although it is not a strategy of clarification, it is a fact that work organization and educative actions have considerable impact in reducing this type of accident, also reducing damage to the life of nurses involved in these accidents.

  17. Risk assessment of maintenance operations: the analysis of performing task and accident mechanism.

    PubMed

    Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos; Guadix, Jose; Onieva, Luis

    2015-01-01

    Maintenance operations cover a great number of occupations. Most small and medium-sized enterprises lack the appropriate information to conduct risk assessments of maintenance operations. The objective of this research is to provide a method based on the concepts of task and accident mechanisms for an initial risk assessment by taking into consideration the prevalence and severity of the maintenance accidents reported. Data were gathered from 11,190 reported accidents in maintenance operations in the manufacturing sector of Andalusia from 2003 to 2012. By using a semi-quantitative methodology, likelihood and severity were evaluated based on the actual distribution of accident mechanisms in each of the tasks. Accident mechanisms and tasks were identified by using those variables included in the European Statistics of Accidents at Work methodology. As main results, the estimated risk of the most frequent accident mechanisms identified for each of the analysed tasks is low and the only accident mechanisms with medium risk are accidents when lifting or pushing with physical stress on the musculoskeletal system in tasks involving carrying, and impacts against objects after slipping or stumbling for tasks involving movements. The prioritisation of public preventive actions for the accident mechanisms with a higher estimated risk is highly recommended.

  18. Accidents in Building Engineering in the European Union Countries in the Years 2008 - 2014

    NASA Astrophysics Data System (ADS)

    Harasymiuk, Jolanta; Tadeusz Barski, Janusz

    2017-10-01

    According to the ESAW1, an accident at work is an event that results in physical or mental harm to the person doing the work. As a result of this incident, fatal accidents may occur (which in the course of one year lead to death of the victim) or non-fatal accidents (that imply at least four full calendar days of absence from work). In the paper the authors present the number and the analysis of the causes of accidents at work in the construction industry in years 2008 - 2014 in 28 countries of the European Union. The descriptive statistics method was used to achieve the intended goal. The accident rate indicator for individual European Union countries has been shown in the analyzed period. The structure and trends of accidents during the period under investigation, divided into two groups: fatal accidents and non-fatal accidents, were presented. Both groups were analyzed for what caused them and what factors affected the quantity (Age of the victim, work experience, month of occurrence). On the basis of the analyzed causes and factors causing accidents in the construction industry in years 2008 - 2014, the classification of EU countries has been shown in terms of accidents. The paper was concluded with a summary.

  19. APT Blanket System Loss-of-Coolant Accident (LOCA) Analysis Based on Initial Conceptual Design - Case 3: External HR Break at Pump Outlet without Pump Trip

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Hamm, L.L.

    1998-10-07

    This report is one of a series of reports that document normal operation and accident simulations for the Accelerator Production of Tritium (APT) blanket heat removal (HR) system. These simulations were performed for the Preliminary Safety Analysis Report.

  20. 10 CFR 100.11 - Determination of exclusion area, low population zone, and population center distance.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... these calculations should be based upon a major accident, hypothesized for purposes of site analysis or... exceeded by those from any accident considered credible. Such accidents have generally been assumed to... total radiation dose to the whole body in excess of 25 rem 2 or a total radiation dose in excess of 300...

  1. 10 CFR 100.11 - Determination of exclusion area, low population zone, and population center distance.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... these calculations should be based upon a major accident, hypothesized for purposes of site analysis or... exceeded by those from any accident considered credible. Such accidents have generally been assumed to... total radiation dose to the whole body in excess of 25 rem 2 or a total radiation dose in excess of 300...

  2. 10 CFR 100.11 - Determination of exclusion area, low population zone, and population center distance.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... these calculations should be based upon a major accident, hypothesized for purposes of site analysis or... exceeded by those from any accident considered credible. Such accidents have generally been assumed to... total radiation dose to the whole body in excess of 25 rem 2 or a total radiation dose in excess of 300...

  3. Work accidents and self-esteem of nursing professional in hospital settings.

    PubMed

    Santos, Sérgio Valverde Marques Dos; Macedo, Flávia Ribeiro Martins; Silva, Luiz Almeida da; Resck, Zelia Marilda Rodrigues; Nogueira, Denismar Alves; Terra, Fábio de Souza

    2017-04-20

    to analyze the occurrence of work accidents and the self-esteem of nurses in hospitals of a municipality of Minas Gerais. descriptive-analytical and cross-sectional study developed with 393 nursing professionals from three hospitals of a municipality in southern Minas Gerais. The Rosenberg Self-Esteem Scale and a questionnaire to characterize the population and work accidents were used for data collection. Data analysis was performed using Person's chi-squared test, Fisher's exact test, Cronbach's alpha, odds ratio and logistic regression. of the professionals studied, 15% had suffered an accident at work and 70.2% presented high self-esteem. Through the analysis, it was observed that smoking, religious belief and an outstanding event in the career were significantly associated with work accidents. In relation to self-esteem, family income, length of time working in the profession and an outstanding event in the career presented significant associations. factors such as smoking, religious belief, family income, length of time working in the profession and an outstanding event in the career can cause professionals to have accidents and/or cause changes in self-esteem, which can compromise their physical and mental health and their quality of life and work.

  4. [Burden of disease attributable to road traffic accidents in the Friuli Venezia Giulia Region (Northeastern Italy)].

    PubMed

    Collarile, Paolo; Gobbino, Iliana; Tripani, Nicola; Zeriali, Luca; Dimai, Matteo; Valent, Francesca

    2014-01-01

    to estimate the health impact of road traffic accidents in the Friuli Venezia Giulia Region, Northeastern Italy. burden of disease (BoD) study. we used data on road traffic accidents collected by the Police in the Friuli Venezia Giulia in 2010 and health data regarding Emergency Room visits, hospital admissions, and deaths. we calculated the Disability Adjusted Life Years (DALY) lost because of road traffic accidents. The kernel density of the DALYs in the region was analyzed and mapped. it was estimated that 3,861 DALYs were lost in 2010. Years lost because of premature deaths outnumbered those lost because of disability. The highest number of DALYs was lost among 15-44-year-old males. Of 14,361 injured persons included in the analysis, only 4,357 were found in the Police database. However, these injuries accounted for 95% of all the DALYs. the present study identified population subgroups with a particularly high impact of road traffic accidents. Educational and Police interventions to prevent accidents should be addressed to those subgroups. In the future, repeating this analysis will allow an evaluation of the effectiveness of preventive interventions in terms of health gains.

  5. Work accidents and self-esteem of nursing professional in hospital settings

    PubMed Central

    dos Santos, Sérgio Valverde Marques; Macedo, Flávia Ribeiro Martins; da Silva, Luiz Almeida; Resck, Zelia Marilda Rodrigues; Nogueira, Denismar Alves; Terra, Fábio de Souza

    2017-01-01

    Abstract Objective: to analyze the occurrence of work accidents and the self-esteem of nurses in hospitals of a municipality of Minas Gerais. Method: descriptive-analytical and cross-sectional study developed with 393 nursing professionals from three hospitals of a municipality in southern Minas Gerais. The Rosenberg Self-Esteem Scale and a questionnaire to characterize the population and work accidents were used for data collection. Data analysis was performed using Person's chi-squared test, Fisher's exact test, Cronbach's alpha, odds ratio and logistic regression. Results: of the professionals studied, 15% had suffered an accident at work and 70.2% presented high self-esteem. Through the analysis, it was observed that smoking, religious belief and an outstanding event in the career were significantly associated with work accidents. In relation to self-esteem, family income, length of time working in the profession and an outstanding event in the career presented significant associations. Conclusion: factors such as smoking, religious belief, family income, length of time working in the profession and an outstanding event in the career can cause professionals to have accidents and/or cause changes in self-esteem, which can compromise their physical and mental health and their quality of life and work. PMID:28443993

  6. Dose-dependent analysis of acute medical effects of mixed neutron-gamma radiation from selected severe 235U or 239Pu criticality accidents in USSR, United States, and Argentina.

    PubMed

    Barabanova, Tatyana; Wiley, Albert L; Bushmanov, Andrey

    2012-04-01

    Eight of the most severe cases of acute radiation disease (ARS) known to have occurred in humans (as the result of criticality accidents) had survival times less than 120 h (herein defined as "early death"). These accidents were analyzed and are discussed with respect to the specific accident scenarios and the resulting accident-specific, mixed neutron-gamma radiation clinical dose distributions. This analysis concludes that the cardiovascular system appears to be the most critical organ system failure for causing "early death" following approximate total body, mixed gamma-neutron radiation doses greater than 40-50 Gy. The clinical data also suggest that there was definite chest dose dependence in the resulting survival times for these eight workers, who unfortunately suffered profound radiation injury and unusual clinical effects from such high dose radiation exposures. In addition, "toxemic syndrome" is correlated with the irradiation of large volumes of soft tissues. Doses to the hands or legs greater than 80-100 Gy or radiation lung injury also play significant but secondary roles in causing "early death" in accidents delivering chest doses greater than 50 Gy.

  7. A Variational Approach to the Analysis of Dissipative Electromechanical Systems

    PubMed Central

    Allison, Andrew; Pearce, Charles E. M.; Abbott, Derek

    2014-01-01

    We develop a method for systematically constructing Lagrangian functions for dissipative mechanical, electrical, and electromechanical systems. We derive the equations of motion for some typical electromechanical systems using deterministic principles that are strictly variational. We do not use any ad hoc features that are added on after the analysis has been completed, such as the Rayleigh dissipation function. We generalise the concept of potential, and define generalised potentials for dissipative lumped system elements. Our innovation offers a unified approach to the analysis of electromechanical systems where there are energy and power terms in both the mechanical and electrical parts of the system. Using our novel technique, we can take advantage of the analytic approach from mechanics, and we can apply these powerful analytical methods to electrical and to electromechanical systems. We can analyse systems that include non-conservative forces. Our methodology is deterministic, and does does require any special intuition, and is thus suitable for automation via a computer-based algebra package. PMID:24586221

  8. An Examination of Safety Management Systems and Aviation Technologies in the Helicopter Emergency Medical Services Industry

    NASA Astrophysics Data System (ADS)

    Buckner, Steven A.

    The Helicopter Emergency Medical Service (HEMS) industry has a significant role in the transportation of injured patients, but has experienced more accidents than all other segments of the aviation industry combined. With the objective of addressing this discrepancy, this study assesses the effect of safety management systems implementation and aviation technologies utilization on the reduction of HEMS accident rates. Participating were 147 pilots from Federal Aviation Regulations Part 135 HEMS operators, who completed a survey questionnaire based on the Safety Culture and Safety Management System Survey (SCSMSS). The study assessed the predictor value of SMS implementation and aviation technologies to the frequency of HEMS accident rates with correlation and multiple linear regression. The correlation analysis identified three significant positive relationships. HEMS years of experience had a high significant positive relationship with accident rate (r=.90; p<.05); SMS had a moderate significant positive relationship to Night Vision Goggles (NVG) (r=.38; p<.05); and SMS had a slight significant positive relationship with Terrain Avoidance Warning System (TAWS) (r=.234; p<.05). Multiple regression analysis suggested that when combined with NVG, TAWS, and SMS, HEMS years of experience explained 81.4% of the variance in accident rate scores (p<.05), and HEMS years of experience was found to be a significant predictor of accident rates (p<.05). Additional quantitative regression analysis was recommended to replicate the results of this study and to consider the influence of these variables for continued reduction of HEMS accidents, and to induce execution of SMS and aviation technologies from a systems engineering application. Recommendations for practice included the adoption of existing regulatory guidance for a SMS program. A qualitative analysis was also recommended for future study SMS implementation and HEMS accident rate from the pilot's perspective. A quantitative longitudinal study would further explore inferential relationships between the study variables. Current strategies should include the increased utilization of available aviation technology resources as this proactive stance may be beneficial for the establishment of an effective safety culture within the HEMS industry.

  9. Toxic release consequence analysis tool (TORCAT) for inherently safer design plant.

    PubMed

    Shariff, Azmi Mohd; Zaini, Dzulkarnain

    2010-10-15

    Many major accidents due to toxic release in the past have caused many fatalities such as the tragedy of MIC release in Bhopal, India (1984). One of the approaches is to use inherently safer design technique that utilizes inherent safety principle to eliminate or minimize accidents rather than to control the hazard. This technique is best implemented in preliminary design stage where the consequence of toxic release can be evaluated and necessary design improvements can be implemented to eliminate or minimize the accidents to as low as reasonably practicable (ALARP) without resorting to costly protective system. However, currently there is no commercial tool available that has such capability. This paper reports on the preliminary findings on the development of a prototype tool for consequence analysis and design improvement via inherent safety principle by utilizing an integrated process design simulator with toxic release consequence analysis model. The consequence analysis based on the worst-case scenarios during process flowsheeting stage were conducted as case studies. The preliminary finding shows that toxic release consequences analysis tool (TORCAT) has capability to eliminate or minimize the potential toxic release accidents by adopting the inherent safety principle early in preliminary design stage. 2010 Elsevier B.V. All rights reserved.

  10. Characteristics of worker accidents on NYSDOT construction projects.

    PubMed

    Mohan, Satish; Zech, Wesley C

    2005-01-01

    This paper aims at providing cost-effective safety measures to protect construction workers in highway work zones, based on real data. Two types of accidents that occur in work zones were: (a) construction work area accidents, and (b) traffic accidents involving construction worker(s). A detailed analysis of work zone accidents involving 36 fatalities and 3,055 severe injuries to construction workers on New York State Department of Transportation (NYSDOT) construction projects from 1990 to 2001 established that five accident types: (a) Struck/Pinned by Large Equipment, (b) Trip or Fall (elevated), (c) Contact w/Electrical or Gas Utility, (d) Struck-by Moving/Falling Load, and (e) Crane/Lift Device Failure accounted for nearly 96% of the fatal accidents, nearly 63% of the hospital-level injury accidents, and nearly 91% of the total costs. These construction work area accidents had a total cost of $133.8 million. Traffic accidents that involve contractors' employees were also examined. Statistical analyses of the traffic accidents established that five traffic accident types: (a) Work Space Intrusion, (b) Worker Struck-by Vehicle Inside Work Space, (c) Flagger Struck-by Vehicle, (d) Worker Struck-by Vehicle Entering/Exiting Work Space, and (e) Construction Equipment Struck-by Vehicle Inside Work Space accounted for nearly 86% of the fatal, nearly 70% of the hospital-level injury and minor injury traffic accidents, and $45.4 million (79.4%) of the total traffic accident costs. The results of this paper provide real statistics on construction worker related accidents reported on construction work zones. Potential preventions based on real statistics have also been suggested. The ranking of accident types, both within the work area as well as in traffic, will guide the heavy highway contractor and owner agencies in identifying the most cost effective safety preventions.

  11. Investigations on optimization of accident management measures following a station blackout accident in a VVER-1000 pressurized water reactor

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Tusheva, P.; Schaefer, F.; Kliem, S.

    2012-07-01

    The reactor safety issues are of primary importance for preserving the health of the population and ensuring no release of radioactivity and fission products into the environment. A part of the nuclear research focuses on improvement of the safety of existing nuclear power plants. Studies, research and efforts are a continuing process at improving the safety and reliability of existing and newly developed nuclear power plants at prevention of a core melt accident. Station blackout (loss of AC power supply) is one of the dominant accidents taken into consideration at performing accident analysis. In case of multiple failures of safetymore » systems it leads to a severe accident. To prevent an accident to turn into a severe one or to mitigate the consequences, accident management measures must be performed. The present paper outlines possibilities for application and optimization of accident management measures following a station blackout accident. Assessed is the behaviour of the nuclear power plant during a station blackout accident without accident management measures and with application of primary/secondary side oriented accident management measures. Discussed are the possibilities for operators ' intervention and the influence of the performed accident management measures on the course of the accident. Special attention has been paid to the effectiveness of the passive feeding and physical phenomena having an influence on the system behaviour. The performed simulations show that the effectiveness of the secondary side feeding procedure can be limited due to an early evaporation or flashing effects in the feed water system. The analyzed cases show that the effectiveness of the accident management measures strongly depends on the initiation criteria applied for depressurization of the reactor coolant system. (authors)« less

  12. Interim MELCOR Simulation of the Fukushima Daiichi Unit 2 Accident Reactor Core Isolation Cooling Operation

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Ross, Kyle W.; Gauntt, Randall O.; Cardoni, Jeffrey N.

    2013-11-01

    Data, a brief description of key boundary conditions, and results of Sandia National Laboratories’ ongoing MELCOR analysis of the Fukushima Unit 2 accident are given for the reactor core isolation cooling (RCIC) system. Important assumptions and related boundary conditions in the current analysis additional to or different than what was assumed/imposed in the work of SAND2012-6173 are identified. This work is for the U.S. Department of Energy’s Nuclear Energy University Programs fiscal year 2014 Reactor Safety Technologies Research and Development Program RC-7: RCIC Performance under Severe Accident Conditions.

  13. Deterministic quantum dense coding networks

    NASA Astrophysics Data System (ADS)

    Roy, Saptarshi; Chanda, Titas; Das, Tamoghna; Sen(De), Aditi; Sen, Ujjwal

    2018-07-01

    We consider the scenario of deterministic classical information transmission between multiple senders and a single receiver, when they a priori share a multipartite quantum state - an attempt towards building a deterministic dense coding network. Specifically, we prove that in the case of two or three senders and a single receiver, generalized Greenberger-Horne-Zeilinger (gGHZ) states are not beneficial for sending classical information deterministically beyond the classical limit, except when the shared state is the GHZ state itself. On the other hand, three- and four-qubit generalized W (gW) states with specific parameters as well as the four-qubit Dicke states can provide a quantum advantage of sending the information in deterministic dense coding. Interestingly however, numerical simulations in the three-qubit scenario reveal that the percentage of states from the GHZ-class that are deterministic dense codeable is higher than that of states from the W-class.

  14. Assessing the safety effects of cooperative intelligent transport systems: A bowtie analysis approach.

    PubMed

    Ehlers, Ute Christine; Ryeng, Eirin Olaussen; McCormack, Edward; Khan, Faisal; Ehlers, Sören

    2017-02-01

    The safety effects of cooperative intelligent transport systems (C-ITS) are mostly unknown and associated with uncertainties, because these systems represent emerging technology. This study proposes a bowtie analysis as a conceptual framework for evaluating the safety effect of cooperative intelligent transport systems. These seek to prevent road traffic accidents or mitigate their consequences. Under the assumption of the potential occurrence of a particular single vehicle accident, three case studies demonstrate the application of the bowtie analysis approach in road traffic safety. The approach utilizes exemplary expert estimates and knowledge from literature on the probability of the occurrence of accident risk factors and of the success of safety measures. Fuzzy set theory is applied to handle uncertainty in expert knowledge. Based on this approach, a useful tool is developed to estimate the effects of safety-related cooperative intelligent transport systems in terms of the expected change in accident occurrence and consequence probability. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Thermal-hydraulic analysis of N Reactor graphite and shield cooling system performance

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Low, J.O.; Schmitt, B.E.

    1988-02-01

    A series of bounding (worst-case) calculations were performed using a detailed hydrodynamic RELAP5 model of the N Reactor graphite and shield cooling system (GSCS). These calculations were specifically aimed to answer issues raised by the Westinghouse Independent Safety Review (WISR) committee. These questions address the operability of the GSCS during a worst-case degraded-core accident that requires the GDCS to mitigate the consequences of the accident. An accident scenario previously developed was designed as the hydrogen-mitigation design-basis accident (HMDBA). Previous HMDBA heat transfer analysis,, using the TRUMP-BD code, was used to define the thermal boundary conditions that the GSDS may bemore » exposed to. These TRUMP/HMDBA analysis results were used to define the bounding operating conditions of the GSCS during the course of an HMDBA transient. Nominal and degraded GSCS scenarios were investigated using RELAP5 within or at the bounds of the HMDBA transient. 10 refs., 42 figs., 10 tabs.« less

  16. [Accidents at work and occupational diseases trend in agriculture insurance management. The contribution of INAIL data's for the knowledge of a worrying phenomenon].

    PubMed

    Calandriello, Luigi; Goggiamani, Angela; Ienzi, Emanuela; Naldini, Silvia; Orsini, Dario

    2013-01-01

    The author's describe accidents at work and occupational diseases outcome's measure in Agricolture insurance management acquired through statistical approach based on data processing provided by INAIL Bank data. Accident's incidence in Agricolture is compared to main insurance managements, using frequency index of accidents appearance selected on line of work and type of consequence. Concerning occupational diseases the authors describes the complaints and compensation with the comparison referring the analysis to statistical general data. The data define a worrying phenomenon.

  17. Risk-based Analysis of Construction Accidents in Iran During 2007-2011-Meta Analyze Study.

    PubMed

    Amiri, Mehran; Ardeshir, Abdollah; Fazel Zarandi, Mohammad Hossein

    2014-04-01

    The present study aimed to investigate the characteristics of occupational accidents and frequency and severity of work related accidents in the construction industry among Iranian insured workers during the years 20072011. The Iranian Social Security Organization (ISSO) accident database containing 21,864 cases between the years 2007-2011 was applied in this study. In the next step, Total Accident Rate (TRA), Total Severity Index (TSI), and Risk Factor (RF) were defined. The core of this work is devoted to analyzing the data from different perspectives such as age of workers, occupation and construction phase, day of the week, time of the day, seasonal analysis, regional considerations, type of accident, and body parts affected. Workers between 15-19 years old (TAR=13.4%) are almost six times more exposed to risk of accident than the average of all ages (TAR=2.51%). Laborers and structural workers (TAR=66.6%) and those working at heights (TAR=47.2%) experience more accidents than other groups of workers. Moreover, older workers over 65 years old (TSI=1.97%> average TSI=1.60%), work supervisors (TSI=12.20% >average TSI=9.09%), and night shift workers (TSI=1.89% >average TSI=1.47%) are more prone to severe accidents. It is recommended that laborers, young workers, weekend and night shift workers be supervised more carefully in the workplace. Use of Personal Protective Equipment (PPE) should be compulsory in working environments, and special attention should be undertaken to people working outdoors and at heights. It is also suggested that policymakers pay more attention to the improvement of safety conditions in deprived and cold western regions.

  18. ADAM: An Accident Diagnostic,Analysis and Management System - Applications to Severe Accident Simulation and Management

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Zavisca, M.J.; Khatib-Rahbar, M.; Esmaili, H.

    2002-07-01

    The Accident Diagnostic, Analysis and Management (ADAM) computer code has been developed as a tool for on-line applications to accident diagnostics, simulation, management and training. ADAM's severe accident simulation capabilities incorporate a balance of mechanistic, phenomenologically based models with simple parametric approaches for elements including (but not limited to) thermal hydraulics; heat transfer; fuel heatup, meltdown, and relocation; fission product release and transport; combustible gas generation and combustion; and core-concrete interaction. The overall model is defined by a relatively coarse spatial nodalization of the reactor coolant and containment systems and is advanced explicitly in time. The result is to enablemore » much faster than real time (i.e., 100 to 1000 times faster than real time on a personal computer) applications to on-line investigations and/or accident management training. Other features of the simulation module include provision for activation of water injection, including the Engineered Safety Features, as well as other mechanisms for the assessment of accident management and recovery strategies and the evaluation of PSA success criteria. The accident diagnostics module of ADAM uses on-line access to selected plant parameters (as measured by plant sensors) to compute the thermodynamic state of the plant, and to predict various margins to safety (e.g., times to pressure vessel saturation and steam generator dryout). Rule-based logic is employed to classify the measured data as belonging to one of a number of likely scenarios based on symptoms, and a number of 'alarms' are generated to signal the state of the reactor and containment. This paper will address the features and limitations of ADAM with particular focus on accident simulation and management. (authors)« less

  19. Risk-based Analysis of Construction Accidents in Iran During 2007-2011-Meta Analyze Study

    PubMed Central

    AMIRI, Mehran; ARDESHIR, Abdollah; FAZEL ZARANDI, Mohammad Hossein

    2014-01-01

    Abstract Background The present study aimed to investigate the characteristics of occupational accidents and frequency and severity of work related accidents in the construction industry among Iranian insured workers during the years 20072011. Methods The Iranian Social Security Organization (ISSO) accident database containing 21,864 cases between the years 2007-2011 was applied in this study. In the next step, Total Accident Rate (TRA), Total Severity Index (TSI), and Risk Factor (RF) were defined. The core of this work is devoted to analyzing the data from different perspectives such as age of workers, occupation and construction phase, day of the week, time of the day, seasonal analysis, regional considerations, type of accident, and body parts affected. Results Workers between 15-19 years old (TAR=13.4%) are almost six times more exposed to risk of accident than the average of all ages (TAR=2.51%). Laborers and structural workers (TAR=66.6%) and those working at heights (TAR=47.2%) experience more accidents than other groups of workers. Moreover, older workers over 65 years old (TSI=1.97%> average TSI=1.60%), work supervisors (TSI=12.20% >average TSI=9.09%), and night shift workers (TSI=1.89% >average TSI=1.47%) are more prone to severe accidents. Conclusion It is recommended that laborers, young workers, weekend and night shift workers be supervised more carefully in the workplace. Use of Personal Protective Equipment (PPE) should be compulsory in working environments, and special attention should be undertaken to people working outdoors and at heights. It is also suggested that policymakers pay more attention to the improvement of safety conditions in deprived and cold western regions. PMID:26005662

  20. Noise as an explanatory factor in work-related fatality reports

    PubMed Central

    Deshaies, Pierre; Martin, Richard; Belzile, Danny; Fortier, Pauline; Laroche, Chantal; Leroux, Tony; Nélisse, Hugues; Girard, Serge-André; Arcand, Robert; Poulin, Maurice; Picard, Michel

    2015-01-01

    Noise exposure in the workplace is a common reality in Québec, Canada as it is elsewhere. However, the extent to which noise acts as a causal or contributive factor in industrial work-related accidents has not been studied thoroughly despite its plausibility. This article aims to describe the importance or potential importance, during investigations looking into the specific causes of each work-related fatal accident, of noise as an explanatory factor. The written information contained in the accident reports pertaining to contextual and technical elements were used. The study used multiple case qualitative content analysis. This descriptive study was based on the content analysis of the 788 reports from the Commission de la santé et de la sécurité du travail du Québec [Workers’ Compensation Board (WCB)] investigating the fatal work-related accidents between 1990 and 2005. The study was descriptive (number and percentages). Noise was explicitly stated as one of the explanatory factors for the fatal outcome in 2.2% (17/788) of the fatal accidents, particularly when the work involved vehicular movement or the need to communicate between workers. Noise was not typically considered a unique cause in the accident, notably because the investigators considered that the accident would have probably occurred due to other risk factors (for example, disregard of safety rules, shortcomings in work methods, and inadequate training). Noise is an important risk factor when communication is involved in work. Since noise is ubiquitous and may also interfere with vigilance and other risk factors for accidents, it may be a much more important contributing factor to accidents than is currently recognized. PMID:26356371

  1. Noise as an explanatory factor in work-related fatality reports.

    PubMed

    Deshaies, Pierre; Martin, Richard; Belzile, Danny; Fortier, Pauline; Laroche, Chantal; Leroux, Tony; Nélisse, Hugues; Girard, Serge-André; Arcand, Robert; Poulin, Maurice; Picard, Michel

    2015-01-01

    Noise exposure in the workplace is a common reality in Québec, Canada as it is elsewhere. However, the extent to which noise acts as a causal or contributive factor in industrial work-related accidents has not been studied thoroughly despite its plausibility. This article aims to describe the importance or potential importance, during investigations looking into the specific causes of each work-related fatal accident, of noise as an explanatory factor. The written information contained in the accident reports pertaining to contextual and technical elements were used. The study used multiple case qualitative content analysis. This descriptive study was based on the content analysis of the 788 reports from the Commission de la santé et de la sécurité du travail du Québec [Workers' Compensation Board (WCB)] investigating the fatal work-related accidents between 1990 and 2005. The study was descriptive (number and percentages). Noise was explicitly stated as one of the explanatory factors for the fatal outcome in 2.2% (17/788) of the fatal accidents, particularly when the work involved vehicular movement or the need to communicate between workers. Noise was not typically considered a unique cause in the accident, notably because the investigators considered that the accident would have probably occurred due to other risk factors (for example, disregard of safety rules, shortcomings in work methods, and inadequate training). Noise is an important risk factor when communication is involved in work. Since noise is ubiquitous and may also interfere with vigilance and other risk factors for accidents, it may be a much more important contributing factor to accidents than is currently recognized.

  2. Aviation Safety: Modeling and Analyzing Complex Interactions between Humans and Automated Systems

    NASA Technical Reports Server (NTRS)

    Rungta, Neha; Brat, Guillaume; Clancey, William J.; Linde, Charlotte; Raimondi, Franco; Seah, Chin; Shafto, Michael

    2013-01-01

    The on-going transformation from the current US Air Traffic System (ATS) to the Next Generation Air Traffic System (NextGen) will force the introduction of new automated systems and most likely will cause automation to migrate from ground to air. This will yield new function allocations between humans and automation and therefore change the roles and responsibilities in the ATS. Yet, safety in NextGen is required to be at least as good as in the current system. We therefore need techniques to evaluate the safety of the interactions between humans and automation. We think that current human factor studies and simulation-based techniques will fall short in front of the ATS complexity, and that we need to add more automated techniques to simulations, such as model checking, which offers exhaustive coverage of the non-deterministic behaviors in nominal and off-nominal scenarios. In this work, we present a verification approach based both on simulations and on model checking for evaluating the roles and responsibilities of humans and automation. Models are created using Brahms (a multi-agent framework) and we show that the traditional Brahms simulations can be integrated with automated exploration techniques based on model checking, thus offering a complete exploration of the behavioral space of the scenario. Our formal analysis supports the notion of beliefs and probabilities to reason about human behavior. We demonstrate the technique with the Ueberligen accident since it exemplifies authority problems when receiving conflicting advices from human and automated systems.

  3. Balloon crash damage and injuries: an analysis of 86 accidents, 2000-2004.

    PubMed

    de Voogt, Alexander J; van Doorn, Robert R A

    2006-05-01

    General aviation accounts for the majority of aviation crashes and casualties in the United States. The role of ballooning in these statistics is not regularly studied. Since 2001, the National Transportation and Safety Board has made its accident reports more readily available, which presents opportunities for further study. This study analyzes and compares a 5-yr period of accident reports and includes an analysis of injuries and balloon damage in hot-air and gas balloon accidents. Balloon crash 2-page briefs and 5-page accident reports published by the National Transportation and Safety Board for the 5-yr time period 2000-2004 were examined. Data collected in the investigation of these crashes were analyzed and compared with the epidemiological data collected in earlier research. In 86 crashes during a 5-yr period, there were 4 fatalities and 75 people were seriously injured. Only one accident was reported involving a student pilot. Broken ankles and legs have been the most commonly recorded serious injury, but could not be linked to the severity of damage to the balloon. The absence of student pilot accidents may be explained by possible stricter supervision. Balloon basket and envelopes appear of sufficient quality to withstand crashes, but improving the protection of passengers during hard landings should help to decrease the number of serious injuries in ballooning.

  4. Preliminary Analysis of Aircraft Loss of Control Accidents: Worst Case Precursor Combinations and Temporal Sequencing

    NASA Technical Reports Server (NTRS)

    Belcastro, Christine M.; Groff, Loren; Newman, Richard L.; Foster, John V.; Crider, Dennis H.; Klyde, David H.; Huston, A. McCall

    2014-01-01

    Aircraft loss of control (LOC) is a leading cause of fatal accidents across all transport airplane and operational classes, and can result from a wide spectrum of hazards, often occurring in combination. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of conditions and uncertainties, including multiple hazards, and their validation must provide a means of assessing system effectiveness and coverage of these hazards. This requires the definition of a comprehensive set of LOC test scenarios based on accident and incident data as well as future risks. This paper defines a comprehensive set of accidents and incidents over a recent 15 year period, and presents preliminary analysis results to identify worst-case combinations of causal and contributing factors (i.e., accident precursors) and how they sequence in time. Such analyses can provide insight in developing effective solutions for LOC, and form the basis for developing test scenarios that can be used in evaluating them. Preliminary findings based on the results of this paper indicate that system failures or malfunctions, crew actions or inactions, vehicle impairment conditions, and vehicle upsets contributed the most to accidents and fatalities, followed by inclement weather or atmospheric disturbances and poor visibility. Follow-on research will include finalizing the analysis through a team consensus process, defining future risks, and developing a comprehensive set of test scenarios with correlation to the accidents, incidents, and future risks. Since enhanced engineering simulations are required for batch and piloted evaluations under realistic LOC precursor conditions, these test scenarios can also serve as a high-level requirement for defining the engineering simulation enhancements needed for generating them.

  5. A systemic analysis of South Korea Sewol ferry accident - Striking a balance between learning and accountability.

    PubMed

    Kee, Dohyung; Jun, Gyuchan Thomas; Waterson, Patrick; Haslam, Roger

    2017-03-01

    The South Korea Sewol ferry accident in April 2014 claimed the lives of over 300 passengers and led to criminal charges of 399 personnel concerned including imprisonment of 154 of them as of Oct 2014. Blame and punishment culture can be prevalent in a more hierarchical society like South Korea as shown in the aftermath of this disaster. This study aims to analyse the South Korea ferry accident using Rasmussen's risk management framework and the associated AcciMap technique and to propose recommendations drawn from an AcciMap-based focus group with systems safety experts. The data for the accident analysis were collected mainly from an interim investigation report by the Board of Audit and Inspection of Korea and major South Korean and foreign newspapers. The analysis showed that the accident was attributed to many contributing factors arising from front-line operators, management, regulators and government. It also showed how the multiple factors including economic, social and political pressures and individual workload contributed to the accident and how they affected each other. This AcciMap was presented to 27 safety researchers and experts at 'the legacy of Jens Rasmussen' symposium adjunct to ODAM2014. Their recommendations were captured through a focus group. The four main recommendations include forgive (no blame and punishment on individuals), analyse (socio-technical system-based), learn (from why things do not go wrong) and change (bottom-up safety culture and safety system management). The findings offer important insights into how this type of accident should be understood, analysed and the subsequent response. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. RDS - A systematic approach towards system thermal hydraulics input code development for a comprehensive deterministic safety analysis

    NASA Astrophysics Data System (ADS)

    Salim, Mohd Faiz; Roslan, Ridha; Ibrahim, Mohd Rizal Mamat @

    2014-02-01

    Deterministic Safety Analysis (DSA) is one of the mandatory requirements conducted for Nuclear Power Plant licensing process, with the aim of ensuring safety compliance with relevant regulatory acceptance criteria. DSA is a technique whereby a set of conservative deterministic rules and requirements are applied for the design and operation of facilities or activities. Computer codes are normally used to assist in performing all required analysis under DSA. To ensure a comprehensive analysis, the conduct of DSA should follow a systematic approach. One of the methodologies proposed is the Standardized and Consolidated Reference Experimental (and Calculated) Database (SCRED) developed by University of Pisa. Based on this methodology, the use of Reference Data Set (RDS) as a pre-requisite reference document for developing input nodalization was proposed. This paper shall describe the application of RDS with the purpose of assessing its effectiveness. Two RDS documents were developed for an Integral Test Facility of LOBI-MOD2 and associated Test A1-83. Data and information from various reports and drawings were referred in preparing the RDS. The results showed that by developing RDS, it has made possible to consolidate all relevant information in one single document. This is beneficial as it enables preservation of information, promotes quality assurance, allows traceability, facilitates continuous improvement, promotes solving of contradictions and finally assisting in developing thermal hydraulic input regardless of whichever code selected. However, some disadvantages were also recognized such as the need for experience in making engineering judgments, language barrier in accessing foreign information and limitation of resources. Some possible improvements are suggested to overcome these challenges.

  7. Physician flight accidents.

    DOT National Transportation Integrated Search

    1966-09-01

    An analysis of physician flight accidents during the period 1964-1965 is presented. More than thirty physicians sustained fatal injuries while piloting light aircraft: a fatality record four times the ratio of physician pilots in the general aviation...

  8. Tularosa Basin Play Fairway Analysis

    DOE Data Explorer

    Adam Brandt

    2015-11-15

    This submission contains several shapefiles used for a deterministic PFA, as well as a heat composite risk segment with union overlay, and training sites used for weights of evidence. More detailed metadata can be found in the specific file.

  9. Demographic variables in coal miners’ safety attitude

    NASA Astrophysics Data System (ADS)

    Yin, Wen-wen; Wu, Xiang; Ci, Hui-Peng; Qin, Shu-Qi; Liu, Jia-Long

    2017-03-01

    To change unsafe behavior through adjusting people’s safety attitudes has become an important measure to prevent accidents. Demographic variables, as influential factors of safety attitude, are fundamental and essential for the research. This research does a questionnaire survey among coal mine industry workers, and makes variance analysis and correlation analysis of the results in light of age, length of working years, educational level and experiences of accidents. The results show that the coal miners’ age, length of working years and accident experiences correlate lowly with safety attitudes, and those older coal miners with longer working years have better safety attitude, as coal miners without experiences of accident do.However, educational level has nothing to do with the safety attitude. Therefore, during the process of safety management, coal miners with different demographic characteristics should be put more attention to.

  10. [Reconstruction of Vehicle-human Crash Accident and Injury Analysis Based on 3D Laser Scanning, Multi-rigid-body Reconstruction and Optimized Genetic Algorithm].

    PubMed

    Sun, J; Wang, T; Li, Z D; Shao, Y; Zhang, Z Y; Feng, H; Zou, D H; Chen, Y J

    2017-12-01

    To reconstruct a vehicle-bicycle-cyclist crash accident and analyse the injuries using 3D laser scanning technology, multi-rigid-body dynamics and optimized genetic algorithm, and to provide biomechanical basis for the forensic identification of death cause. The vehicle was measured by 3D laser scanning technology. The multi-rigid-body models of cyclist, bicycle and vehicle were developed based on the measurements. The value range of optimal variables was set. A multi-objective genetic algorithm and the nondominated sorting genetic algorithm were used to find the optimal solutions, which were compared to the record of the surveillance video around the accident scene. The reconstruction result of laser scanning on vehicle was satisfactory. In the optimal solutions found by optimization method of genetic algorithm, the dynamical behaviours of dummy, bicycle and vehicle corresponded to that recorded by the surveillance video. The injury parameters of dummy were consistent with the situation and position of the real injuries on the cyclist in accident. The motion status before accident, damage process by crash and mechanical analysis on the injury of the victim can be reconstructed using 3D laser scanning technology, multi-rigid-body dynamics and optimized genetic algorithm, which have application value in the identification of injury manner and analysis of death cause in traffic accidents. Copyright© by the Editorial Department of Journal of Forensic Medicine

  11. Final safety analysis report for the Galileo mission: Volume 3 (Book 2), Nuclear risk analysis document: Appendices: Revision 1

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Not Available

    1989-01-25

    It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with ifmore » there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.« less

  12. Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015.

    PubMed

    Mehmandar, Mohammadreza; Soori, Hamid; Mehrabi, Yadolah

    2016-01-01

    Predicting the trend in traffic accidents deaths and its analysis can be a useful tool for planning and policy-making, conducting interventions appropriate with death trend, and taking the necessary actions required for controlling and preventing future occurrences. Predicting and analyzing the trend of traffic accidents deaths in Iran in 2014 and 2015. It was a cross-sectional study. All the information related to fatal traffic accidents available in the database of Iran Legal Medicine Organization from 2004 to the end of 2013 were used to determine the change points (multi-variable time series analysis). Using autoregressive integrated moving average (ARIMA) model, traffic accidents death rates were predicted for 2014 and 2015, and a comparison was made between this rate and the predicted value in order to determine the efficiency of the model. From the results, the actual death rate in 2014 was almost similar to that recorded for this year, while in 2015 there was a decrease compared with the previous year (2014) for all the months. A maximum value of 41% was also predicted for the months of January and February, 2015. From the prediction and analysis of the death trends, proper application and continuous use of the intervention conducted in the previous years for road safety improvement, motor vehicle safety improvement, particularly training and culture-fostering interventions, as well as approval and execution of deterrent regulations for changing the organizational behaviors, can significantly decrease the loss caused by traffic accidents.

  13. Safety analysis report for the Galileo Mission. Volume 3, book 2: Nuclear risk analysis document. Appendices, revision 1

    NASA Astrophysics Data System (ADS)

    1989-01-01

    It is the purpose of the NRAD to provide an analysis of the range of potential consequences of accidents which have been identified that are associated with the launching and deployment of the Galileo mission spacecraft. The specific consequences analyzed are those associated with the possible release of radioactive material (fuel) of the Radioisotope Thermoelectric Generators (RTGs). They are in terms of radiation doses to people and areas of deposition of radioactive material. These consequence analyses can be used in several ways. One way is to identify the potential range of consequences which might have to be dealt with if there were to be an accident with a release of fuel, so as to assure that, given such an accident, the health and safety of the public will be reasonably protected. Another use of the information, in conjunction with accident and release probabilities, is to estimate the risks associated with the mission. That is, most space launches occur without incident. Given an accident, the most probable result relative to the RTGs is complete containment of the radioactive material. Only a small fraction of accidents might result in a release of fuel and subsequent radiological consequences. The combination of probability with consequence is risk, which can be compared to other human and societal risks to assure that no undue risks are implied by undertaking the mission. Book 2 contains eight appendices.

  14. On Transform Domain Communication Systems under Spectrum Sensing Mismatch: A Deterministic Analysis.

    PubMed

    Jin, Chuanxue; Hu, Su; Huang, Yixuan; Luo, Qu; Huang, Dan; Li, Yi; Gao, Yuan; Cheng, Shaochi

    2017-07-08

    Towards the era of mobile Internet and the Internet of Things (IoT), numerous sensors and devices are being introduced and interconnected. To support such an amount of data traffic, traditional wireless communication technologies are facing challenges both in terms of the increasing shortage of spectrum resources and massive multiple access. The transform-domain communication system (TDCS) is considered as an alternative multiple access system, where 5G and mobile IoT are mainly focused. However, previous studies about TDCS are under the assumption that the transceiver has the global spectrum information, without the consideration of spectrum sensing mismatch (SSM). In this paper, we present the deterministic analysis of TDCS systems under arbitrary given spectrum sensing scenarios, especially the influence of the SSM pattern to the signal to noise ratio (SNR) performance. Simulation results show that arbitrary SSM pattern can lead to inferior bit error rate (BER) performance.

  15. Fuzzy linear model for production optimization of mining systems with multiple entities

    NASA Astrophysics Data System (ADS)

    Vujic, Slobodan; Benovic, Tomo; Miljanovic, Igor; Hudej, Marjan; Milutinovic, Aleksandar; Pavlovic, Petar

    2011-12-01

    Planning and production optimization within multiple mines or several work sites (entities) mining systems by using fuzzy linear programming (LP) was studied. LP is the most commonly used operations research methods in mining engineering. After the introductory review of properties and limitations of applying LP, short reviews of the general settings of deterministic and fuzzy LP models are presented. With the purpose of comparative analysis, the application of both LP models is presented using the example of the Bauxite Basin Niksic with five mines. After the assessment, LP is an efficient mathematical modeling tool in production planning and solving many other single-criteria optimization problems of mining engineering. After the comparison of advantages and deficiencies of both deterministic and fuzzy LP models, the conclusion presents benefits of the fuzzy LP model but is also stating that seeking the optimal plan of production means to accomplish the overall analysis that will encompass the LP model approaches.

  16. On Transform Domain Communication Systems under Spectrum Sensing Mismatch: A Deterministic Analysis

    PubMed Central

    Jin, Chuanxue; Hu, Su; Huang, Yixuan; Luo, Qu; Huang, Dan; Li, Yi; Cheng, Shaochi

    2017-01-01

    Towards the era of mobile Internet and the Internet of Things (IoT), numerous sensors and devices are being introduced and interconnected. To support such an amount of data traffic, traditional wireless communication technologies are facing challenges both in terms of the increasing shortage of spectrum resources and massive multiple access. The transform-domain communication system (TDCS) is considered as an alternative multiple access system, where 5G and mobile IoT are mainly focused. However, previous studies about TDCS are under the assumption that the transceiver has the global spectrum information, without the consideration of spectrum sensing mismatch (SSM). In this paper, we present the deterministic analysis of TDCS systems under arbitrary given spectrum sensing scenarios, especially the influence of the SSM pattern to the signal to noise ratio (SNR) performance. Simulation results show that arbitrary SSM pattern can lead to inferior bit error rate (BER) performance. PMID:28698477

  17. A space radiation transport method development

    NASA Technical Reports Server (NTRS)

    Wilson, J. W.; Tripathi, R. K.; Qualls, G. D.; Cucinotta, F. A.; Prael, R. E.; Norbury, J. W.; Heinbockel, J. H.; Tweed, J.

    2004-01-01

    Improved spacecraft shield design requires early entry of radiation constraints into the design process to maximize performance and minimize costs. As a result, we have been investigating high-speed computational procedures to allow shield analysis from the preliminary design concepts to the final design. In particular, we will discuss the progress towards a full three-dimensional and computationally efficient deterministic code for which the current HZETRN evaluates the lowest-order asymptotic term. HZETRN is the first deterministic solution to the Boltzmann equation allowing field mapping within the International Space Station (ISS) in tens of minutes using standard finite element method (FEM) geometry common to engineering design practice enabling development of integrated multidisciplinary design optimization methods. A single ray trace in ISS FEM geometry requires 14 ms and severely limits application of Monte Carlo methods to such engineering models. A potential means of improving the Monte Carlo efficiency in coupling to spacecraft geometry is given in terms of re-configurable computing and could be utilized in the final design as verification of the deterministic method optimized design. Published by Elsevier Ltd on behalf of COSPAR.

  18. Development of DCGLs by using both probabilistic and deterministic analyses in RESRAD (onsite) and RESRAD-OFFSITE codes.

    PubMed

    Kamboj, Sunita; Yu, Charley; Johnson, Robert

    2013-05-01

    The Derived Concentration Guideline Levels for two building areas previously used in waste processing and storage at Argonne National Laboratory were developed using both probabilistic and deterministic radiological environmental pathway analysis. Four scenarios were considered. The two current uses considered were on-site industrial use and off-site residential use with farming. The two future uses (i.e., after an institutional control period of 100 y) were on-site recreational use and on-site residential use with farming. The RESRAD-OFFSITE code was used for the current-use off-site residential/farming scenario and RESRAD (onsite) was used for the other three scenarios. Contaminants of concern were identified from the past operations conducted in the buildings and the actual characterization done at the site. Derived Concentration Guideline Levels were developed for all four scenarios using deterministic and probabilistic approaches, which include both "peak-of-the-means" and "mean-of-the-peaks" analyses. The future-use on-site residential/farming scenario resulted in the most restrictive Derived Concentration Guideline Levels for most radionuclides.

  19. Integrated Arrival and Departure Schedule Optimization Under Uncertainty

    NASA Technical Reports Server (NTRS)

    Xue, Min; Zelinski, Shannon

    2014-01-01

    In terminal airspace, integrating arrivals and departures with shared waypoints provides the potential of improving operational efficiency by allowing direct routes when possible. Incorporating stochastic evaluation as a post-analysis process of deterministic optimization, and imposing a safety buffer in deterministic optimization, are two ways to learn and alleviate the impact of uncertainty and to avoid unexpected outcomes. This work presents a third and direct way to take uncertainty into consideration during the optimization. The impact of uncertainty was incorporated into cost evaluations when searching for the optimal solutions. The controller intervention count was computed using a heuristic model and served as another stochastic cost besides total delay. Costs under uncertainty were evaluated using Monte Carlo simulations. The Pareto fronts that contain a set of solutions were identified and the trade-off between delays and controller intervention count was shown. Solutions that shared similar delays but had different intervention counts were investigated. The results showed that optimization under uncertainty could identify compromise solutions on Pareto fonts, which is better than deterministic optimization with extra safety buffers. It helps decision-makers reduce controller intervention while achieving low delays.

  20. Using Bayesian Model Averaging (BMA) to calibrate probabilistic surface temperature forecasts over Iran

    NASA Astrophysics Data System (ADS)

    Soltanzadeh, I.; Azadi, M.; Vakili, G. A.

    2011-07-01

    Using Bayesian Model Averaging (BMA), an attempt was made to obtain calibrated probabilistic numerical forecasts of 2-m temperature over Iran. The ensemble employs three limited area models (WRF, MM5 and HRM), with WRF used with five different configurations. Initial and boundary conditions for MM5 and WRF are obtained from the National Centers for Environmental Prediction (NCEP) Global Forecast System (GFS) and for HRM the initial and boundary conditions come from analysis of Global Model Europe (GME) of the German Weather Service. The resulting ensemble of seven members was run for a period of 6 months (from December 2008 to May 2009) over Iran. The 48-h raw ensemble outputs were calibrated using BMA technique for 120 days using a 40 days training sample of forecasts and relative verification data. The calibrated probabilistic forecasts were assessed using rank histogram and attribute diagrams. Results showed that application of BMA improved the reliability of the raw ensemble. Using the weighted ensemble mean forecast as a deterministic forecast it was found that the deterministic-style BMA forecasts performed usually better than the best member's deterministic forecast.

  1. Analysis of stochastic model for non-linear volcanic dynamics

    NASA Astrophysics Data System (ADS)

    Alexandrov, D.; Bashkirtseva, I.; Ryashko, L.

    2014-12-01

    Motivated by important geophysical applications we consider a dynamic model of the magma-plug system previously derived by Iverson et al. (2006) under the influence of stochastic forcing. Due to strong nonlinearity of the friction force for solid plug along its margins, the initial deterministic system exhibits impulsive oscillations. Two types of dynamic behavior of the system under the influence of the parametric stochastic forcing have been found: random trajectories are scattered on both sides of the deterministic cycle or grouped on its internal side only. It is shown that dispersions are highly inhomogeneous along cycles in the presence of noises. The effects of noise-induced shifts, pressure stabilization and localization of random trajectories have been revealed with increasing the noise intensity. The plug velocity, pressure and displacement are highly dependent of noise intensity as well. These new stochastic phenomena are related with the nonlinear peculiarities of the deterministic phase portrait. It is demonstrated that the repetitive stick-slip motions of the magma-plug system in the case of stochastic forcing can be connected with drumbeat earthquakes.

  2. Professional experience and traffic accidents/near-miss accidents among truck drivers.

    PubMed

    Girotto, Edmarlon; Andrade, Selma Maffei de; González, Alberto Durán; Mesas, Arthur Eumann

    2016-10-01

    To investigate the relationship between the time working as a truck driver and the report of involvement in traffic accidents or near-miss accidents. A cross-sectional study was performed with truck drivers transporting products from the Brazilian grain harvest to the Port of Paranaguá, Paraná, Brazil. The drivers were interviewed regarding sociodemographic characteristics, working conditions, behavior in traffic and involvement in accidents or near-miss accidents in the previous 12 months. Subsequently, the participants answered a self-applied questionnaire on substance use. The time of professional experience as drivers was categorized in tertiles. Statistical analyses were performed through the construction of models adjusted by multinomial regression to assess the relationship between the length of experience as a truck driver and the involvement in accidents or near-miss accidents. This study included 665 male drivers with an average age of 42.2 (±11.1) years. Among them, 7.2% and 41.7% of the drivers reported involvement in accidents and near-miss accidents, respectively. In fully adjusted analysis, the 3rd tertile of professional experience (>22years) was shown to be inversely associated with involvement in accidents (odds ratio [OR] 0.29; 95% confidence interval [CI] 0.16-0.52) and near-miss accidents (OR 0.17; 95% CI 0.05-0.53). The 2nd tertile of professional experience (11-22 years) was inversely associated with involvement in accidents (OR 0.63; 95% CI 0.40-0.98). An evident relationship was observed between longer professional experience and a reduction in reporting involvement in accidents and near-miss accidents, regardless of age, substance use, working conditions and behavior in traffic. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Accidents in the greenhouse-construction industry of SE Spain.

    PubMed

    Pérez-Alonso, José; Carreño-Ortega, Angel; Vázquez-Cabrera, Fernando J; Callejón-Ferre, Angel Jesús

    2012-01-01

    This work analyses the labour accidents in the greenhouse-construction industry of SE Spain for the period 1999-2007 through a sample of 180 accident reports. The accidents were characterised by studying 5 variables in order to know the day of the week in which the accident occurred, the hour of the day of the accident, type of accident, the region of Spain in which the accident happened, and the resulting injury. The data characterising the accidents were submitted to a descriptive multiple-correspondence analysis. The incidence of accidents in the greenhouse-construction industry presented a high mean value of 15133.7 per 100,000 workers per year. The days with the greatest incidence of accidents were Thursday and Monday, while the period of greatest number of accidents occurred in the first 4h of the workday. No significant correspondence was found between the day of the week, the hour of the day, or any of the other 3 variables studied. The types of accidents with most frequency were: cuts, punctures, contact with hard or rough material, overexertion, and falls from one level to another. The most affected parts of the anatomy were the eyes, thorax, back, sides, lower legs, and feet. The most common types of injury were bone fractures, twists and sprains, distended muscles, contusions, and being crushed. The study calls attention to the high number of accidents at work, which needs to be corrected by fulfilment of safety regulations at work, on the part of the company. Finally, recommendations are made to correct this situation of high number of accidents at work. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  4. Frequency of Specific Categories of Aviation Accidents and Incidents During 2001-2010

    NASA Technical Reports Server (NTRS)

    Evans, Joni K.

    2014-01-01

    The purpose of this study was to determine the types of accidents or incidents that are most important to the aviation safety risk. All accidents and incidents from 2001-2010 were assigned occurrence categories based on the taxonomy developed by the Commercial Aviation Safety Team/International Civil Aviation Organization (CAST/ICAO) Common Taxonomy Team (CICTT). The most frequently recorded categories were selected within each of five metrics: total accidents, fatal accidents, total injuries, fatal injuries and total incidents. This analysis was done separately for events within Part 121, Scheduled Part 135, Non-Scheduled Part 135 and Part 91. Combining those five sets of categories resulted in groups of between seven and eleven occurrence categories, depending on the flight operation. These groups represent 65-85% of all accidents and 68-81% of incidents.

  5. Space Propulsion Hazards Analysis Manual (SPHAM). Volume 2. Appendices

    DTIC Science & Technology

    1988-10-01

    lb. RESTRICTIVE MARKINGS UNCLASSIFIED 2a. SECURITY CLASSIFICATION AUTHORITY 3 . DISTRIBUTION/AVAILABILITY OF REPORT Approved for public release...Volume I Chapter 2 - Requirementb and the Hazards Analysis Process .... Volume I Chapter 3 - Accident Scenarios...list of the hazardous materials that are discussed; 3 ) description of the failure scenarios; 4) type of post-accident environment that is discussed

  6. Analysis of roadside inspection data and its relationship to accident and safety/compliance review data and reviews of previous and ongoing research in these areas

    DOT National Transportation Integrated Search

    1993-01-01

    The main objective of the present study is to analyze roadside inspection data and its relationship to safety/compliance review and accident data. Data used for this analysis is provided by the Office of Motor Carriers and includes a sample of larger...

  7. INDUSTRIAL/MILITARY ACTIVITY-INITIATED ACCIDENT SCREENING ANALYSIS

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    D.A. Kalinich

    1999-09-27

    Impacts due to nearby installations and operations were determined in the Preliminary MGDS Hazards Analysis (CRWMS M&O 1996) to be potentially applicable to the proposed repository at Yucca Mountain. This determination was conservatively based on limited knowledge of the potential activities ongoing on or off the Nevada Test Site (NTS). It is intended that the Industrial/Military Activity-Initiated Accident Screening Analysis provided herein will meet the requirements of the ''Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants'' (NRC 1987) in establishing whether this external event can be screened from further consideration or must be includedmore » as a design basis event (DBE) in the development of accident scenarios for the Monitored Geologic Repository (MGR). This analysis only considers issues related to preclosure radiological safety. Issues important to waste isolation as related to impact from nearby installations will be covered in the MGR performance assessment.« less

  8. Efficient analysis of stochastic gene dynamics in the non-adiabatic regime using piecewise deterministic Markov processes

    PubMed Central

    2018-01-01

    Single-cell experiments show that gene expression is stochastic and bursty, a feature that can emerge from slow switching between promoter states with different activities. In addition to slow chromatin and/or DNA looping dynamics, one source of long-lived promoter states is the slow binding and unbinding kinetics of transcription factors to promoters, i.e. the non-adiabatic binding regime. Here, we introduce a simple analytical framework, known as a piecewise deterministic Markov process (PDMP), that accurately describes the stochastic dynamics of gene expression in the non-adiabatic regime. We illustrate the utility of the PDMP on a non-trivial dynamical system by analysing the properties of a titration-based oscillator in the non-adiabatic limit. We first show how to transform the underlying chemical master equation into a PDMP where the slow transitions between promoter states are stochastic, but whose rates depend upon the faster deterministic dynamics of the transcription factors regulated by these promoters. We show that the PDMP accurately describes the observed periods of stochastic cycles in activator and repressor-based titration oscillators. We then generalize our PDMP analysis to more complicated versions of titration-based oscillators to explain how multiple binding sites lengthen the period and improve coherence. Last, we show how noise-induced oscillation previously observed in a titration-based oscillator arises from non-adiabatic and discrete binding events at the promoter site. PMID:29386401

  9. Identification of gene regulation models from single-cell data

    NASA Astrophysics Data System (ADS)

    Weber, Lisa; Raymond, William; Munsky, Brian

    2018-09-01

    In quantitative analyses of biological processes, one may use many different scales of models (e.g. spatial or non-spatial, deterministic or stochastic, time-varying or at steady-state) or many different approaches to match models to experimental data (e.g. model fitting or parameter uncertainty/sloppiness quantification with different experiment designs). These different analyses can lead to surprisingly different results, even when applied to the same data and the same model. We use a simplified gene regulation model to illustrate many of these concerns, especially for ODE analyses of deterministic processes, chemical master equation and finite state projection analyses of heterogeneous processes, and stochastic simulations. For each analysis, we employ MATLAB and PYTHON software to consider a time-dependent input signal (e.g. a kinase nuclear translocation) and several model hypotheses, along with simulated single-cell data. We illustrate different approaches (e.g. deterministic and stochastic) to identify the mechanisms and parameters of the same model from the same simulated data. For each approach, we explore how uncertainty in parameter space varies with respect to the chosen analysis approach or specific experiment design. We conclude with a discussion of how our simulated results relate to the integration of experimental and computational investigations to explore signal-activated gene expression models in yeast (Neuert et al 2013 Science 339 584–7) and human cells (Senecal et al 2014 Cell Rep. 8 75–83)5.

  10. Thermal-Structural Optimization of Integrated Cryogenic Propellant Tank Concepts for a Reusable Launch Vehicle

    NASA Technical Reports Server (NTRS)

    Johnson, Theodore F.; Waters, W. Allen; Singer, Thomas N.; Haftka, Raphael T.

    2004-01-01

    A next generation reusable launch vehicle (RLV) will require thermally efficient and light-weight cryogenic propellant tank structures. Since these tanks will be weight-critical, analytical tools must be developed to aid in sizing the thickness of insulation layers and structural geometry for optimal performance. Finite element method (FEM) models of the tank and insulation layers were created to analyze the thermal performance of the cryogenic insulation layer and thermal protection system (TPS) of the tanks. The thermal conditions of ground-hold and re-entry/soak-through for a typical RLV mission were used in the thermal sizing study. A general-purpose nonlinear FEM analysis code, capable of using temperature and pressure dependent material properties, was used as the thermal analysis code. Mechanical loads from ground handling and proof-pressure testing were used to size the structural geometry of an aluminum cryogenic tank wall. Nonlinear deterministic optimization and reliability optimization techniques were the analytical tools used to size the geometry of the isogrid stiffeners and thickness of the skin. The results from the sizing study indicate that a commercial FEM code can be used for thermal analyses to size the insulation thicknesses where the temperature and pressure were varied. The results from the structural sizing study show that using combined deterministic and reliability optimization techniques can obtain alternate and lighter designs than the designs obtained from deterministic optimization methods alone.

  11. Panel summary report

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Gutjahr, A.L.; Kincaid, C.T.; Mercer, J.W.

    1987-04-01

    The objective of this report is to summarize the various modeling approaches that were used to simulate solute transport in a variably saturated emission. In particular, the technical strengths and weaknesses of each approach are discussed, and conclusions and recommendations for future studies are made. Five models are considered: (1) one-dimensional analytical and semianalytical solutions of the classical deterministic convection-dispersion equation (van Genuchten, Parker, and Kool, this report ); (2) one-dimensional simulation using a continuous-time Markov process (Knighton and Wagenet, this report); (3) one-dimensional simulation using the time domain method and the frequency domain method (Duffy and Al-Hassan, this report);more » (4) one-dimensional numerical approach that combines a solution of the classical deterministic convection-dispersion equation with a chemical equilibrium speciation model (Cederberg, this report); and (5) three-dimensional numerical solution of the classical deterministic convection-dispersion equation (Huyakorn, Jones, Parker, Wadsworth, and White, this report). As part of the discussion, the input data and modeling results are summarized. The models were used in a data analysis mode, as opposed to a predictive mode. Thus, the following discussion will concentrate on the data analysis aspects of model use. Also, all the approaches were similar in that they were based on a convection-dispersion model of solute transport. Each discussion addresses the modeling approaches in the order listed above.« less

  12. Fumonisin B1 Toxicity in Grower-Finisher Pigs: A Comparative Analysis of Genetically Engineered Bt Corn and non-Bt Corn by Using Quantitative Dietary Exposure Assessment Modeling

    PubMed Central

    Delgado, James E.; Wolt, Jeffrey D.

    2011-01-01

    In this study, we investigate the long-term exposure (20 weeks) to fumonisin B1 (FB1) in grower-finisher pigs by conducting a quantitative exposure assessment (QEA). Our analytical approach involved both deterministic and semi-stochastic modeling for dietary comparative analyses of FB1 exposures originating from genetically engineered Bacillus thuringiensis (Bt)-corn, conventional non-Bt corn and distiller’s dried grains with solubles (DDGS) derived from Bt and/or non-Bt corn. Results from both deterministic and semi-stochastic demonstrated a distinct difference of FB1 toxicity in feed between Bt corn and non-Bt corn. Semi-stochastic results predicted the lowest FB1 exposure for Bt grain with a mean of 1.5 mg FB1/kg diet and the highest FB1 exposure for a diet consisting of non-Bt grain and non-Bt DDGS with a mean of 7.87 mg FB1/kg diet; the chronic toxicological incipient level of concern is 1.0 mg of FB1/kg of diet. Deterministic results closely mirrored but tended to slightly under predict the mean result for the semi-stochastic analysis. This novel comparative QEA model reveals that diet scenarios where the source of grain is derived from Bt corn presents less potential to induce FB1 toxicity than diets containing non-Bt corn. PMID:21909298

  13. Common features and peculiarities of the seismic activity at Phlegraean Fields, Long Valley, and Vesuvius

    USGS Publications Warehouse

    Marzocchi, W.; Vilardo, G.; Hill, D.P.; Ricciardi, G.P.; Ricco, C.

    2001-01-01

    We analyzed and compared the seismic activity that has occurred in the last two to three decades in three distinct volcanic areas: Phlegraean Fields, Italy; Vesuvius, Italy; and Long Valley, California. Our main goal is to identify and discuss common features and peculiarities in the temporal evolution of earthquake sequences that may reflect similarities and differences in the generating processes between these volcanic systems. In particular, we tried to characterize the time series of the number of events and of the seismic energy release in terms of stochastic, deterministic, and chaotic components. The time sequences from each area consist of thousands of earthquakes that allow a detailed quantitative analysis and comparison. The results obtained showed no evidence for either deterministic or chaotic components in the earthquake sequences in Long Valley caldera, which appears to be dominated by stochastic behavior. In contrast, earthquake sequences at Phlegrean Fields and Mount Vesuvius show a deterministic signal mainly consisting of a 24-hour periodicity. Our analysis suggests that the modulation in seismicity is in some way related to thermal diurnal processes, rather than luni-solar tidal effects. Independently from the process that generates these periodicities on the seismicity., it is suggested that the lack (or presence) of diurnal cycles is seismic swarms of volcanic areas could be closely linked to the presence (or lack) of magma motion.

  14. Unconditional security proof of a deterministic quantum key distribution with a two-way quantum channel

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Lu Hua; Department of Mathematics and Physics, Hubei University of Technology, Wuhan 430068; Fung, Chi-Hang Fred

    2011-10-15

    In a deterministic quantum key distribution (DQKD) protocol with a two-way quantum channel, Bob sends a qubit to Alice who then encodes a key bit onto the qubit and sends it back to Bob. After measuring the returned qubit, Bob can obtain Alice's key bit immediately, without basis reconciliation. Since an eavesdropper may attack the qubits traveling on either the Bob-Alice channel or the Alice-Bob channel, the security analysis of DQKD protocol with a two-way quantum channel is complicated and its unconditional security has been controversial. This paper presents a security proof of a single-photon four-state DQKD protocol against generalmore » attacks.« less

  15. [The drama of hyperextension trauma--chronic whiplash syndrome with its neuropsychological and psychiatric findings. An analysis of 80 cases from expert assessment].

    PubMed

    Kissel, W

    1999-10-28

    The problem "whiplash associated disorder" was studied in a multidisciplinary analysis of 80 patients who all had a "simple whiplash-accident", this means a whiplash-accident without concomitant head trauma apart from contact with the car seat and without unconsciousness. The opinions of a rheumatologist and of a psychiatrist were considered in each case, and in 47 patients, a neuropsychological expertise was present. 43% of the patients who had been neuropsychologically tested revealed specific cognitive deficits as they are described after mild traumatic brain injuries and after whiplash accidents. Symptoms related to a pretraumatic cognitive disease were not found in any of the cases. Most patients had been professionally active at the time of the accident, some performing activities requiring a high level of cognitive skill. 66% percent of the study group showed psychological disturbances reducing the working capacity. There was no evidence for preexisting traumatic psychiatric symptoms. In many cases the psychiatric disturbances were accident-related, either reactive to the cognitive deficiencies or resulting from chronic pain. We assume that the "simple whiplash-accident" can cause chronic disturbances of brain function. In the etiology, a mild traumatic brain damage must be considered, this means an organic damage and not only a functional brain disorder. These brain function disturbances are often masked by the pure psychiatric symptoms, therefore they must be carefully searched for. Injured patients, who do not regain their working capacity after the accident, should be explored in a neuropsychological as well as in a psychiatric mode as early as possible after the accident.

  16. Off-road truck-related accidents in U.S. mines

    PubMed Central

    Dindarloo, Saeid R.; Pollard, Jonisha P.; Siami-Irdemoosa, Elnaz

    2016-01-01

    Introduction Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. Methods A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Results Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5 years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. Conclusions The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Practical application Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. PMID:27620937

  17. Off-road truck-related accidents in U.S. mines.

    PubMed

    Dindarloo, Saeid R; Pollard, Jonisha P; Siami-Irdemoosa, Elnaz

    2016-09-01

    Off-road trucks are one of the major sources of equipment-related accidents in the U.S. mining industries. A systematic analysis of all off-road truck-related accidents, injuries, and illnesses, which are reported and published by the Mine Safety and Health Administration (MSHA), is expected to provide practical insights for identifying the accident patterns and trends in the available raw database. Therefore, appropriate safety management measures can be administered and implemented based on these accident patterns/trends. A hybrid clustering-classification methodology using K-means clustering and gene expression programming (GEP) is proposed for the analysis of severe and non-severe off-road truck-related injuries at U.S. mines. Using the GEP sub-model, a small subset of the 36 recorded attributes was found to be correlated to the severity level. Given the set of specified attributes, the clustering sub-model was able to cluster the accident records into 5 distinct groups. For instance, the first cluster contained accidents related to minerals processing mills and coal preparation plants (91%). More than two-thirds of the victims in this cluster had less than 5years of job experience. This cluster was associated with the highest percentage of severe injuries (22 severe accidents, 3.4%). Almost 50% of all accidents in this cluster occurred at stone operations. Similarly, the other four clusters were characterized to highlight important patterns that can be used to determine areas of focus for safety initiatives. The identified clusters of accidents may play a vital role in the prevention of severe injuries in mining. Further research into the cluster attributes and identified patterns will be necessary to determine how these factors can be mitigated to reduce the risk of severe injuries. Analyzing injury data using data mining techniques provides some insight into attributes that are associated with high accuracies for predicting injury severity. Copyright © 2016 Elsevier Ltd and National Safety Council. All rights reserved.

  18. The role of personality traits and driving experience in self-reported risky driving behaviors and accident risk among Chinese drivers.

    PubMed

    Tao, Da; Zhang, Rui; Qu, Xingda

    2017-02-01

    The purpose of this study was to explore the role of personality traits and driving experience in the prediction of risky driving behaviors and accident risk among Chinese population. A convenience sample of drivers (n=511; mean (SD) age=34.2 (8.8) years) completed a self-report questionnaire that was designed based on validated scales for measuring personality traits, risky driving behaviors and self-reported accident risk. Results from structural equation modeling analysis demonstrated that the data fit well with our theoretical model. While showing no direct effects on accident risk, personality traits had direct effects on risky driving behaviors, and yielded indirect effects on accident risk mediated by risky driving behaviors. Both driving experience and risky driving behaviors directly predicted accident risk and accounted for 15% of its variance. There was little gender difference in personality traits, risky driving behaviors and accident risk. The findings emphasized the importance of personality traits and driving experience in the understanding of risky driving behaviors and accident risk among Chinese drivers and provided new insight into the design of evidence-based driving education and accident prevention interventions. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. A decade of occupational accidents due to direct or indirect electrical contact in the primary, secondary and tertiary sectors in Spain (2003-2012).

    PubMed

    Castillo-Rosa, Juan; Suárez-Cebador, Manuel; Rubio-Romero, Juan Carlos; Aguado, Jose Antonio

    2017-03-01

    Occupational accidents caused by electrical contact are a major concern worldwide due to their severe consequences. The study conducted is based on an analysis of the evolution of incidence rates and dependence between variables for 14,022 electrical accidents occurring in Spain between 2003 and 2012. The results show that electrical accidents as a whole are 3.6 times more likely to have severe consequences than the rest of the accidents in the country. This proportion is even nine times greater in the case of fatal accidents. They also confirm a significant relationship between the severity of this type of accidents and the economic sector in which they occur. On the other hand, there is a positive trend in the reduction of the incidence rate, especially in relation to direct contact, although unexpectedly the rate of accidents due to indirect contact is on the rise. Thus, preventing electrical occupational accidents requires efforts to guarantee adequate training adapted to the needs of workers in the various economic sectors. Furthermore, those responsible for safety should work to implement mechanisms to monitor and control compliance with efficient protective measures against electrical contact.

  20. Occupational accidents among mototaxi drivers.

    PubMed

    Amorim, Camila Rego; de Araújo, Edna Maria; de Araújo, Tânia Maria; de Oliveira, Nelson Fernandes

    2012-03-01

    The use of motorcycles as a means of work has contributed to the increase in traffic accidents, in particular, mototaxi accidents. The aim of this study was to estimate and characterize the incidence of occupational accidents among the mototaxis registered in Feira de Santana, BA. This is a cross-sectional study with descriptive and census data. Of the 300 professionals registered at the Municipal Transportation Service, 267 professionals were interviewed through a structured questionnaire. Then, a descriptive analysis was conducted and the incidence of accidents was estimated based on the variables studied. Relative risks were calculated and statistical significance was determined using the chi-square test and Fisher's exact test, considering p < 0.05. Logistic regression was used in order to perform simultaneous adjustment of variables. Occupational accidents were observed in 10.5% of mototaxis. There were mainly minor injuries (48.7%), 27% of them requiring leaves of absence from work. There was an association between the days of work per week, fatigue in lower limbs and musculoskeletal complaints, and accidents. Knowledge of the working conditions and accidents involved in this activity can be of great importance for the adoption of traffic education policies, and to help prevent accidents by improving the working conditions and lives of these professionals.

  1. [Spatial analysis of road traffic accidents with fatalities in Spain, 2008-2011].

    PubMed

    Gómez-Barroso, Diana; López-Cuadrado, Teresa; Llácer, Alicia; Palmera Suárez, Rocío; Fernández-Cuenca, Rafael

    2015-09-01

    To estimate the areas of greatest density of road traffic accidents with fatalities at 24 hours per km(2)/year in Spain from 2008 to 2011, using a geographic information system. Accidents were geocodified using the road and kilometer points where they occurred. The average nearest neighbor was calculated to detect possible clusters and to obtain the bandwidth for kernel density estimation. A total of 4775 accidents were analyzed, of which 73.3% occurred on conventional roads. The estimated average distance between accidents was 1,242 meters, and the average expected distance was 10,738 meters. The nearest neighbor index was 0.11, indicating that there were aggregations of accidents in space. A map showing the kernel density was obtained with a resolution of 1 km(2), which identified the areas of highest density. This methodology allowed a better approximation to locating accident risks by taking into account kilometer points. The map shows areas where there was a greater density of accidents. This could be an advantage in decision-making by the relevant authorities. Copyright © 2014 SESPAS. Published by Elsevier Espana. All rights reserved.

  2. Benchmarking MARS (accident management software) with the Browns Ferry fire

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Dawson, S.M.; Liu, L.Y.; Raines, J.C.

    1992-01-01

    The MAAP Accident Response System (MARS) is a userfriendly computer software developed to provide management and engineering staff with the most needed insights, during actual or simulated accidents, of the current and future conditions of the plant based on current plant data and its trends. To demonstrate the reliability of the MARS code in simulatng a plant transient, MARS is being benchmarked with the available reactor pressure vessel (RPV) pressure and level data from the Browns Ferry fire. The MRS software uses the Modular Accident Analysis Program (MAAP) code as its basis to calculate plant response under accident conditions. MARSmore » uses a limited set of plant data to initialize and track the accidnt progression. To perform this benchmark, a simulated set of plant data was constructed based on actual report data containing the information necessary to initialize MARS and keep track of plant system status throughout the accident progression. The initial Browns Ferry fire data were produced by performing a MAAP run to simulate the accident. The remaining accident simulation used actual plant data.« less

  3. Systematic strategies for the third industrial accident prevention plan in Korea.

    PubMed

    Kang, Young-sig; Yang, Sung-hwan; Kim, Tae-gu; Kim, Day-sung

    2012-01-01

    To minimize industrial accidents, it's critical to evaluate a firm's priorities for prevention factors and strategies since such evaluation provides decisive information for preventing industrial accidents and maintaining safety management. Therefore, this paper proposes the evaluation of priorities through statistical testing of prevention factors with a cause analysis in a cause and effect model. A priority matrix criterion is proposed to apply the ranking and for the objectivity of questionnaire results. This paper used regression method (RA), exponential smoothing method (ESM), double exponential smoothing method (DESM), autoregressive integrated moving average (ARIMA) model and proposed analytical function method (PAFM) to analyze trends of accident data that will lead to an accurate prediction. This paper standardized the questionnaire results of workers and managers in manufacturing and construction companies with less than 300 employees, located in the central Korean metropolitan areas where fatal accidents have occurred. Finally, a strategy was provided to construct safety management for the third industrial accident prevention plan and a forecasting method for occupational accident rates and fatality rates for occupational accidents per 10,000 people.

  4. Coupling the System Analysis Module with SAS4A/SASSYS-1

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Fanning, T. H.; Hu, R.

    2016-09-30

    SAS4A/SASSYS-1 is a simulation tool used to perform deterministic analysis of anticipated events as well as design basis and beyond design basis accidents for advanced reactors, with an emphasis on sodium fast reactors. SAS4A/SASSYS-1 has been under development and in active use for nearly forty-five years, and is currently maintained by the U.S. Department of Energy under the Office of Advanced Reactor Technology. Although SAS4A/SASSYS-1 contains a very capable primary and intermediate system modeling component, PRIMAR-4, it also has some shortcomings: outdated data management and code structure makes extension of the PRIMAR-4 module somewhat difficult. The user input format formore » PRIMAR-4 also limits the number of volumes and segments that can be used to describe a given system. The System Analysis Module (SAM) is a fairly new code development effort being carried out under the U.S. DOE Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. SAM is being developed with advanced physical models, numerical methods, and software engineering practices; however, it is currently somewhat limited in the system components and phenomena that can be represented. For example, component models for electromagnetic pumps and multi-layer stratified volumes have not yet been developed. Nor is there support for a balance of plant model. Similarly, system-level phenomena such as control-rod driveline expansion and vessel elongation are not represented. This report documents fiscal year 2016 work that was carried out to couple the transient safety analysis capabilities of SAS4A/SASSYS-1 with the system modeling capabilities of SAM under the joint support of the ART and NEAMS programs. The coupling effort was successful and is demonstrated by evaluating an unprotected loss of flow transient for the Advanced Burner Test Reactor (ABTR) design. There are differences between the stand-alone SAS4A/SASSYS-1 simulations and the coupled SAS/SAM simulations, but these are mainly attributed to the limited maturity of the SAM development effort. The severe accident modeling capabilities in SAS4A/SASSYS-1 (sodium boiling, fuel melting and relocation) will continue to play a vital role for a long time. Therefore, the SAS4A/SASSYS-1 modernization effort should remain a high priority task under the ART program to ensure continued participation in domestic and international SFR safety collaborations and design optimizations. On the other hand, SAM provides an advanced system analysis tool, with improved numerical solution schemes, data management, code flexibility, and accuracy. SAM is still in early stages of development and will require continued support from NEAMS to fulfill its potential and to mature into a production tool for advanced reactor safety analysis. The effort to couple SAS4A/SASSYS-1 and SAM is the first step on the integration of these modeling capabilities.« less

  5. General RMP Guidance - Table of Contents

    EPA Pesticide Factsheets

    The Risk Management Programs for Chemical Accident Prevention (40 CFR Part 68) guidance is in chapters; each covering topics such as applicability of the rule, and requirements for reporting five-year accident history and offsite consequence analysis.

  6. Protecting the AG pilot.

    DOT National Transportation Integrated Search

    1966-09-01

    Summarized data resulting from a detailed review of fatal and non-fatal aerial applicator accidents are presented with an analysis of the factors underlying the accidents. The role of toxic substance is evaluated. Preventive and newer therapeutic app...

  7. A profile of fatal accidents involving alcohol

    DOT National Transportation Integrated Search

    1977-09-01

    Author's abstract: Accident investigation studies were conducted during 1971-75 in the cities of Boston, Baltimore, Oklahoma City and Albuquerque where Alcohol Safety Action Programs (ASAPs) were operating. Analysis of the four studies, plus newly av...

  8. Airway accidents in critical care unit: A 3-year retrospective study in a Public Teaching Hospital of Eastern India

    PubMed Central

    Dasgupta, Sugata; Singh, Shipti Shradha; Chaudhuri, Arunima; Bhattacharya, Dipasri; Choudhury, Sourav Das

    2016-01-01

    Background: Although tracheal tubes are essential devices to control and protect airway in a critical care unit (CCU), they are not free from complications. Aims: To document the incidence and nature of airway accidents in the CCU of a government teaching hospital in Eastern India. Methods: Retrospective analysis of all airway accidents in a 5-bedded (medical and surgical) CCU. The number, types, timing, and severity of airway accidents were analyzed. Results: The total accident rate was 19 in 233 intubated and/or tracheostomized patients over 1657 tube days (TDs) during 3 years. Fourteen occurred in 232 endotracheally intubated patients over 1075 endotracheal tube (ETT) days, and five occurred in 44 tracheostomized patients over 580 tracheostomy TDs. Fifteen accidents were due to blocked tubes. Rest four were unplanned extubations (UEs), all being accidental extubations. All blockages occurred during night shifts and all UEs during day shifts. Five accidents were mild, the rest moderate. No major accident led to cardiorespiratory arrest or death. All blockages occurred after 7th day of intubation. The outcome of accidents were more favorable in tracheostomy group compared to ETT group (P = 0.001). Conclusions: The prevalence of airway accidents was 8.2 accidents per 100 patients. Blockages were the most common accidents followed by UEs. Ten out of the 15 blockages and all 4 UEs were in endotracheally intubated patients. Tracheostomized patients had 5 blockages and no UEs. PMID:27076709

  9. Review the number of accidents in Tehran over a two-year period and prediction of the number of events based on a time-series model

    PubMed Central

    Teymuri, Ghulam Heidar; Sadeghian, Marzieh; Kangavari, Mehdi; Asghari, Mehdi; Madrese, Elham; Abbasinia, Marzieh; Ahmadnezhad, Iman; Gholizadeh, Yavar

    2013-01-01

    Background: One of the significant dangers that threaten people’s lives is the increased risk of accidents. Annually, more than 1.3 million people die around the world as a result of accidents, and it has been estimated that approximately 300 deaths occur daily due to traffic accidents in the world with more than 50% of that number being people who were not even passengers in the cars. The aim of this study was to examine traffic accidents in Tehran and forecast the number of future accidents using a time-series model. Methods: The study was a cross-sectional study that was conducted in 2011. The sample population was all traffic accidents that caused death and physical injuries in Tehran in 2010 and 2011, as registered in the Tehran Emergency ward. The present study used Minitab 15 software to provide a description of accidents in Tehran for the specified time period as well as those that occurred during April 2012. Results: The results indicated that the average number of daily traffic accidents in Tehran in 2010 was 187 with a standard deviation of 83.6. In 2011, there was an average of 180 daily traffic accidents with a standard deviation of 39.5. One-way analysis of variance indicated that the average number of accidents in the city was different for different months of the year (P < 0.05). Most of the accidents occurred in March, July, August, and September. Thus, more accidents occurred in the summer than in the other seasons. The number of accidents was predicted based on an auto-regressive, moving average (ARMA) for April 2012. The number of accidents displayed a seasonal trend. The prediction of the number of accidents in the city during April of 2012 indicated that a total of 4,459 accidents would occur with mean of 149 accidents per day during these three months. Conclusion: The number of accidents in Tehran displayed a seasonal trend, and the number of accidents was different for different seasons of the year. PMID:26120405

  10. Analysis of accidents in nine Iranian gas refineries: 2007-2011.

    PubMed

    Mehrdad, R; Bolouri, A; Shakibmanesh, A R

    2013-10-01

    Occupational accidents are one of the major health hazards in industries and associated with high mortality, morbidity, spiritual damage and economic losses in the world. To determine the incidence of occupational accidents in 9 Iranian gas refineries between March 2007 and February 2011. Data on all occupational accidents occurred between March 2007 and February 2011, as well as other possible associated variables including time of accident, whether the accident was due to a personal or systemic fault, type of accident and its outcomes, age and gender of the victim, the injured parts of the body, job experience, and type of employment, were extracted from HSE reports and notes of health care services. Based on these data, we calculated the incidence rate of accidents and assessed the associated factors. During the 5 studied years, 1129 accidents have been recorded. The incidence of fatal accidents was 1.64 per 100 000 and of nonfatal accidents was 1857 per 100 000 workers per year. 99.4% of injured workers were male. The mean±SD age of injured people was 29.6±7.3 years. Almost 70% of injured workers aged under 30 years. The mean±SD job experience was 5.3±5.3 years. Accidents occurred more commonly around 10:00. More than 60% of accidents happened between 8:00 and 15:00. July had the highest incidence rate. The most common type of accident was being struck by an object (48%). More than 94% of accidents are caused by personal rather than systemic faults. Hands and wrists were the most common injured parts and involved in more than one-third of accidents. 70% of injured workers needed medical treatment and returned to work after primary treatment. The pattern of occupational accidents in Iranian gas refineries is similar to other previous reports in many ways. The incidence did not change significantly over the study period. Establishment of an online network for precise registration, notification and meticulous data collection seems necessary.

  11. Truck Drivers' Experiences and Perspectives Regarding Factors Influencing Traffic Accidents: A Qualitative Study.

    PubMed

    Karimi Moonaghi, Hossein; Ranjbar, Hossein; Heydari, Abbas; Scurlock-Evans, Laura

    2015-08-01

    Traffic accidents are a major public health problem, leading to death and disability. Although pertinent studies have been conducted, little data are available in Iran. This study explored the experiences of truck drivers and their perspectives regarding factors contributing to traffic accidents. Eighteen truck drivers, purposively sampled, participated in semi-structured interviews. Data were analyzed using qualitative content analysis. A main theme, lack of ability to control stress, emerged as a factor influencing the incidence of traffic accidents. This main theme was found to have three subthemes: poor organization of the job, lack of workplace facilities and proper equipment, and unsupportive environment. Although several factors were found to contribute to traffic accidents, their effects were not independent, and all were considered significant. Identifying factors that contribute to traffic accidents requires a systematic and holistic approach. Findings could be used by the transportation industry and community health centers to prevent traffic accidents. © 2015 The Author(s).

  12. Longitudinal Trends in Fall Accidents in Community Dwelling Korean Adults: The 2008-2013 Korean Community Health Survey.

    PubMed

    Hong, Ickpyo; Simpson, Annie N; Logan, Sarah; Woo, Hee-Soon

    2016-08-01

    To describe the longitudinal characteristics of unintentional fall accidents using a representative population-based sample of Korean adults. We examined data from the Korean Community Health Survey from 2008 to 2013. Univariate analysis and multivariable logistic regression were used to identify the characteristics of fall accidents in adults. Between 2008 and 2013, the incidence rate of fall accidents requiring medical treatment increased from 1,248 to 3,423 per 100,000 people (p<0.001), while the proportion of indoor fall accidents decreased from 38.12% to 23.16% (p<0.001). Females had more annual fall accidents than males (p<0.001). The major reason for fall accidents was slippery floors (33.7% in 2011 and 36.3% in 2013). Between 2008 and 2010, variables associated with higher fall accident risk included specific months (August and September), old age, female gender, current drinker, current smoker, diabetes, osteoarthritis, osteoporosis, and depression. A high level of education and living with a partner were negatively associated with fall accident risk. In 2013, people experiencing more than 1 fall accident felt more fear of falling than those having no fall accidents (odds ratio [OR] for 1 fall, 2.12; 95% confidence interval [CI], 2.04-2.12; OR for more than 2 falls, 2.97; 95% CI, 2.83-3.10). The occurrence of fall accidents has consistently increased in Korea from 2008 to 2013. Future intervention studies are needed to reduce the increasing incidence rates of fall accidents in community dwelling adults.

  13. Longitudinal Trends in Fall Accidents in Community Dwelling Korean Adults: The 2008–2013 Korean Community Health Survey

    PubMed Central

    Logan, Sarah

    2016-01-01

    Objective To describe the longitudinal characteristics of unintentional fall accidents using a representative population-based sample of Korean adults. Methods We examined data from the Korean Community Health Survey from 2008 to 2013. Univariate analysis and multivariable logistic regression were used to identify the characteristics of fall accidents in adults. Results Between 2008 and 2013, the incidence rate of fall accidents requiring medical treatment increased from 1,248 to 3,423 per 100,000 people (p<0.001), while the proportion of indoor fall accidents decreased from 38.12% to 23.16% (p<0.001). Females had more annual fall accidents than males (p<0.001). The major reason for fall accidents was slippery floors (33.7% in 2011 and 36.3% in 2013). Between 2008 and 2010, variables associated with higher fall accident risk included specific months (August and September), old age, female gender, current drinker, current smoker, diabetes, osteoarthritis, osteoporosis, and depression. A high level of education and living with a partner were negatively associated with fall accident risk. In 2013, people experiencing more than 1 fall accident felt more fear of falling than those having no fall accidents (odds ratio [OR] for 1 fall, 2.12; 95% confidence interval [CI], 2.04–2.12; OR for more than 2 falls, 2.97; 95% CI, 2.83–3.10). Conclusion The occurrence of fall accidents has consistently increased in Korea from 2008 to 2013. Future intervention studies are needed to reduce the increasing incidence rates of fall accidents in community dwelling adults. PMID:27606272

  14. Ensemble assimilation of ARGO temperature profile, sea surface temperature, and altimetric satellite data into an eddy permitting primitive equation model of the North Atlantic Ocean

    NASA Astrophysics Data System (ADS)

    Yan, Y.; Barth, A.; Beckers, J. M.; Candille, G.; Brankart, J. M.; Brasseur, P.

    2015-07-01

    Sea surface height, sea surface temperature, and temperature profiles at depth collected between January and December 2005 are assimilated into a realistic eddy permitting primitive equation model of the North Atlantic Ocean using the Ensemble Kalman Filter. Sixty ensemble members are generated by adding realistic noise to the forcing parameters related to the temperature. The ensemble is diagnosed and validated by comparison between the ensemble spread and the model/observation difference, as well as by rank histogram before the assimilation experiments. An incremental analysis update scheme is applied in order to reduce spurious oscillations due to the model state correction. The results of the assimilation are assessed according to both deterministic and probabilistic metrics with independent/semiindependent observations. For deterministic validation, the ensemble means, together with the ensemble spreads are compared to the observations, in order to diagnose the ensemble distribution properties in a deterministic way. For probabilistic validation, the continuous ranked probability score (CRPS) is used to evaluate the ensemble forecast system according to reliability and resolution. The reliability is further decomposed into bias and dispersion by the reduced centered random variable (RCRV) score in order to investigate the reliability properties of the ensemble forecast system. The improvement of the assimilation is demonstrated using these validation metrics. Finally, the deterministic validation and the probabilistic validation are analyzed jointly. The consistency and complementarity between both validations are highlighted.

  15. Stochasticity, succession, and environmental perturbations in a fluidic ecosystem.

    PubMed

    Zhou, Jizhong; Deng, Ye; Zhang, Ping; Xue, Kai; Liang, Yuting; Van Nostrand, Joy D; Yang, Yunfeng; He, Zhili; Wu, Liyou; Stahl, David A; Hazen, Terry C; Tiedje, James M; Arkin, Adam P

    2014-03-04

    Unraveling the drivers of community structure and succession in response to environmental change is a central goal in ecology. Although the mechanisms shaping community structure have been intensively examined, those controlling ecological succession remain elusive. To understand the relative importance of stochastic and deterministic processes in mediating microbial community succession, a unique framework composed of four different cases was developed for fluidic and nonfluidic ecosystems. The framework was then tested for one fluidic ecosystem: a groundwater system perturbed by adding emulsified vegetable oil (EVO) for uranium immobilization. Our results revealed that groundwater microbial community diverged substantially away from the initial community after EVO amendment and eventually converged to a new community state, which was closely clustered with its initial state. However, their composition and structure were significantly different from each other. Null model analysis indicated that both deterministic and stochastic processes played important roles in controlling the assembly and succession of the groundwater microbial community, but their relative importance was time dependent. Additionally, consistent with the proposed conceptual framework but contradictory to conventional wisdom, the community succession responding to EVO amendment was primarily controlled by stochastic rather than deterministic processes. During the middle phase of the succession, the roles of stochastic processes in controlling community composition increased substantially, ranging from 81.3% to 92.0%. Finally, there are limited successional studies available to support different cases in the conceptual framework, but further well-replicated explicit time-series experiments are needed to understand the relative importance of deterministic and stochastic processes in controlling community succession.

  16. Convergence studies of deterministic methods for LWR explicit reflector methodology

    DOE Office of Scientific and Technical Information (OSTI.GOV)

    Canepa, S.; Hursin, M.; Ferroukhi, H.

    2013-07-01

    The standard approach in modem 3-D core simulators, employed either for steady-state or transient simulations, is to use Albedo coefficients or explicit reflectors at the core axial and radial boundaries. In the latter approach, few-group homogenized nuclear data are a priori produced with lattice transport codes using 2-D reflector models. Recently, the explicit reflector methodology of the deterministic CASMO-4/SIMULATE-3 code system was identified to potentially constitute one of the main sources of errors for core analyses of the Swiss operating LWRs, which are all belonging to GII design. Considering that some of the new GIII designs will rely on verymore » different reflector concepts, a review and assessment of the reflector methodology for various LWR designs appeared as relevant. Therefore, the purpose of this paper is to first recall the concepts of the explicit reflector modelling approach as employed by CASMO/SIMULATE. Then, for selected reflector configurations representative of both GII and GUI designs, a benchmarking of the few-group nuclear data produced with the deterministic lattice code CASMO-4 and its successor CASMO-5, is conducted. On this basis, a convergence study with regards to geometrical requirements when using deterministic methods with 2-D homogenous models is conducted and the effect on the downstream 3-D core analysis accuracy is evaluated for a typical GII deflector design in order to assess the results against available plant measurements. (authors)« less

  17. Risk analysis of urban gas pipeline network based on improved bow-tie model

    NASA Astrophysics Data System (ADS)

    Hao, M. J.; You, Q. J.; Yue, Z.

    2017-11-01

    Gas pipeline network is a major hazard source in urban areas. In the event of an accident, there could be grave consequences. In order to understand more clearly the causes and consequences of gas pipeline network accidents, and to develop prevention and mitigation measures, the author puts forward the application of improved bow-tie model to analyze risks of urban gas pipeline network. The improved bow-tie model analyzes accident causes from four aspects: human, materials, environment and management; it also analyzes the consequences from four aspects: casualty, property loss, environment and society. Then it quantifies the causes and consequences. Risk identification, risk analysis, risk assessment, risk control, and risk management will be clearly shown in the model figures. Then it can suggest prevention and mitigation measures accordingly to help reduce accident rate of gas pipeline network. The results show that the whole process of an accident can be visually investigated using the bow-tie model. It can also provide reasons for and predict consequences of an unfortunate event. It is of great significance in order to analyze leakage failure of gas pipeline network.

  18. Usefulness of high resolution coastal models for operational oil spill forecast: the Full City accident

    NASA Astrophysics Data System (ADS)

    Broström, G.; Carrasco, A.; Hole, L. R.; Dick, S.; Janssen, F.; Mattsson, J.; Berger, S.

    2011-06-01

    Oil spill modeling is considered to be an important decision support system (DeSS) useful for remedial action in case of accidents, as well as for designing the environmental monitoring system that is frequently set up after major accidents. Many accidents take place in coastal areas implying that low resolution basin scale ocean models is of limited use for predicting the trajectories of an oil spill. In this study, we target the oil spill in connection with the Full City accident on the Norwegian south coast and compare three different oil spill models for the area. The result of the analysis is that all models do a satisfactory job. The "standard" operational model for the area is shown to have severe flaws but including an analysis based on a higher resolution model (1.5 km resolution) for the area the model system show results that compare well with observations. The study also shows that an ensemble using three different models is useful when predicting/analyzing oil spill in coastal areas.

  19. U.S. Civil Rotorcraft Accidents, 1963 Through 1997

    NASA Technical Reports Server (NTRS)

    Harris, Franklin D.; Kasper, Eugene F.; Iseler, Laura E.

    2000-01-01

    Narrative summary data produced by the U.S. National Transportation Safety Board (NTSB) has been obtained and analyzed for all 8,436 U.S. civil registered rotorcraft accidents which occurred from mid-1963 through 1997. This analysis was based on the NTSB's assignment of each mishap into one of 21 "first event" categories. The number of U.S. civil registered rotorcraft as recorded by the Federal Aviation Administration (FAA) for the same period has also been obtained. Taken together, these data indicate the civil rotorcraft accident rate (on a per 1,000 registered rotorcraft basis) has decreased by almost a factor of 10 (i.e., from 130 accidents per 1,000 rotorcraft in 1964 to 13.4 per 1,000 in 1997). Analysis of the mishap data indicates over 70% of the rotorcraft accidents were associated with one of the following four NTSB "first event" categories: 2408 Loss of engine power (28.5%); 1,322 In-flight collisions with objects (15.7%); 1,114 Loss of control (13.2%); 1,083 Airframe/component/system failure or malfunction (12.8%).

  20. Comparing the Identification of Recommendations by Different Accident Investigators Using a Common Methodology

    NASA Technical Reports Server (NTRS)

    Johnson, Chris W.; Oltedal, H. A.; Holloway, C. M.

    2012-01-01

    Accident reports play a key role in the safety of complex systems. These reports present the recommendations that are intended to help avoid any recurrence of past failures. However, the value of these findings depends upon the causal analysis that helps to identify the reasons why an accident occurred. Various techniques have been developed to help investigators distinguish root causes from contributory factors and contextual information. This paper presents the results from a study into the individual differences that can arise when a group of investigators independently apply the same technique to identify the causes of an accident. This work is important if we are to increase the consistency and coherence of investigations following major accidents.

Some links on this page may take you to non-federal websites. Their policies may differ from this site.
Top