A diffusion-free and linear-energy-transfer-independent nanocomposite Fricke gel dosimeter

NASA Astrophysics Data System (ADS)

Maeyama, T.; Fukunishi, N.; Ishikawa, K. L.; Furuta, T.; Fukasaku, K.; Takagi, S.; Noda, S.; Himeno, R.; Fukuda, S.

2014-03-01

We report a new magnetic-resonance-imaging (MRI) based nanocomposite Fricke gel (NC-FG) dosimeter system, which is free from two main drawbacks of conventional Fricke gel dosimeters, namely, the diffusion of the radiation products and the linear-energy-transfer (LET) dependence of the radiation sensitivity when used for ion beams. The NC-FG dosimeter was prepared by incorporating 1% (w/w) clay nanoparticles into deaerated Fricke gel. We have dosimetrically characterized the NC-FG by using MRI measurements after irradiation with a monoenergetic 290 MeV/nucleon carbon beam. No diffusion of the radiation products was observed during nine days after the irradiation. Moreover, its response faithfully reproduced the depth-dose distribution measured by an ionization chamber, which indicates the absence of the LET dependence. Also, the NC-FG dosimeter exhibited a good linearity up to 800 Gy.

Validating Fricke dosimetry for the measurement of absorbed dose to water for HDR 192Ir brachytherapy: a comparison between primary standards of the LCR, Brazil, and the NRC, Canada.

PubMed

Salata, Camila; David, Mariano Gazineu; de Almeida, Carlos Eduardo; El Gamal, Islam; Cojocaru, Claudiu; Mainegra-Hing, Ernesto; McEwen, Malcom

2018-04-05

Two Fricke-based absorbed dose to water standards for HDR Ir-192 dosimetry, developed independently by the LCR in Brazil and the NRC in Canada have been compared. The agreement in the determination of the dose rate from a HDR Ir-192 source at 1 cm in a water phantom was found to be within the k  =  1 combined measurement uncertainties of the two standards: D NRC /D LCR   =  1.011, standard uncertainty  =  2.2%. The dose-based standards also agreed within the uncertainties with the manufacturer's stated dose rate value, which is traceable to a national standard of air kerma. A number of possible influence quantities were investigated, including the specific method for producing the ferrous-sulphate Fricke solution, the geometry of the holder, and the Monte Carlo code used to determine correction factors. The comparison highlighted the lack of data on the determination of G(Fe 3+ ) in this energy range and the possibilities for further development of the holders used to contain the Fricke solution. The comparison also confirmed the suitability of Fricke dosimetry for Ir-192 primary standard dose rate determinations at therapy dose levels.

Validating Fricke dosimetry for the measurement of absorbed dose to water for HDR 192Ir brachytherapy: a comparison between primary standards of the LCR, Brazil, and the NRC, Canada

NASA Astrophysics Data System (ADS)

Salata, Camila; Gazineu David, Mariano; de Almeida, Carlos Eduardo; El Gamal, Islam; Cojocaru, Claudiu; Mainegra-Hing, Ernesto; McEwen, Malcom

2018-04-01

Two Fricke-based absorbed dose to water standards for HDR Ir-192 dosimetry, developed independently by the LCR in Brazil and the NRC in Canada have been compared. The agreement in the determination of the dose rate from a HDR Ir-192 source at 1 cm in a water phantom was found to be within the k  =  1 combined measurement uncertainties of the two standards: D NRC/D LCR  =  1.011, standard uncertainty  =  2.2%. The dose-based standards also agreed within the uncertainties with the manufacturer’s stated dose rate value, which is traceable to a national standard of air kerma. A number of possible influence quantities were investigated, including the specific method for producing the ferrous-sulphate Fricke solution, the geometry of the holder, and the Monte Carlo code used to determine correction factors. The comparison highlighted the lack of data on the determination of G(Fe3+) in this energy range and the possibilities for further development of the holders used to contain the Fricke solution. The comparison also confirmed the suitability of Fricke dosimetry for Ir-192 primary standard dose rate determinations at therapy dose levels.

Frick on FD during Expedition 16/STS-122 Joint Operations

NASA Image and Video Library

2008-02-10

S122-E-007578 (10 Feb. 2008) --- Astronaut Steve Frick, STS-122 commander, is pictured with a package of food while occupying the commander's station on the flight deck of Space Shuttle Atlantis while docked with the International Space Station.

A Comparison of the Performance of Efficient Data Analysis Versus Fine Particle Dose as Metrics for the Quality Control of Aerodynamic Particle Size Distributions of Orally Inhaled Pharmaceuticals.

PubMed

Tougas, Terrence P; Goodey, Adrian P; Hardwell, Gareth; Mitchell, Jolyon; Lyapustina, Svetlana

2017-02-01

The performance of two quality control (QC) tests for aerodynamic particle size distributions (APSD) of orally inhaled drug products (OIPs) is compared. One of the tests is based on the fine particle dose (FPD) metric currently expected by the European regulators. The other test, called efficient data analysis (EDA), uses the ratio of large particle mass to small particle mass (LPM/SPM), along with impactor sized mass (ISM), to detect changes in APSD for QC purposes. The comparison is based on analysis of APSD data from four products (two different pressurized metered dose inhalers (MDIs) and two dry powder inhalers (DPIs)). It is demonstrated that in each case, EDA is able to detect shifts and abnormalities that FPD misses. The lack of sensitivity on the part of FPD is due to its "aggregate" nature, since FPD is a univariate measure of all particles less than about 5 μm aerodynamic diameter, and shifts or changes within the range encompassed by this metric may go undetected. EDA is thus shown to be superior to FPD for routine control of OIP quality. This finding augments previously reported superiority of EDA compared with impactor stage groupings (favored by US regulators) for incorrect rejections (type I errors) when incorrect acceptances (type II errors) were adjusted to the same probability for both approaches. EDA is therefore proposed as a method of choice for routine quality control of OIPs in both European and US regulatory environments.

Product Quality Research Institute evaluation of cascade impactor profiles of pharmaceutical aerosols: part 2--evaluation of a method for determining equivalence.

PubMed

Christopher, David; Adams, Wallace P; Lee, Douglas S; Morgan, Beth; Pan, Ziqing; Singh, Gur Jai Pal; Tsong, Yi; Lyapustina, Svetlana

2007-01-19

The purpose of this article is to present the thought process, methods, and interim results of a PQRI Working Group, which was charged with evaluating the chi-square ratio test as a potential method for determining in vitro equivalence of aerodynamic particle size distribution (APSD) profiles obtained from cascade impactor measurements. Because this test was designed with the intention of being used as a tool in regulatory review of drug applications, the capability of the test to detect differences in APSD profiles correctly and consistently was evaluated in a systematic way across a designed space of possible profiles. To establish a "base line," properties of the test in the simplest case of pairs of identical profiles were studied. Next, the test's performance was studied with pairs of profiles, where some difference was simulated in a systematic way on a single deposition site using realistic product profiles. The results obtained in these studies, which are presented in detail here, suggest that the chi-square ratio test in itself is not sufficient to determine equivalence of particle size distributions. This article, therefore, introduces the proposal to combine the chi-square ratio test with a test for impactor-sized mass based on Population Bioequivalence and describes methods for evaluating discrimination capabilities of the combined test. The approaches and results described in this article elucidate some of the capabilities and limitations of the original chi-square ratio test and provide rationale for development of additional tests capable of comparing APSD profiles of pharmaceutical aerosols.

Fricke-gel dosimetry in epithermal or thermal neutron beams of a research reactor

NASA Astrophysics Data System (ADS)

Gambarini, G.; Artuso, E.; Giove, D.; Volpe, L.; Agosteo, S.; Barcaglioni, L.; Campi, F.; Garlati, L.; Pola, A.; Durisi, E.; Borroni, M.; Carrara, M.; Klupak, V.; Marek, M.; Viererbl, L.; Vins, M.; d'Errico, F.

2015-11-01

Fricke-xylenol-orange gel has shown noticeable potentiality for in-phantom dosimetry in epithermal or thermal neutron fields with very high fluence rate, as those characteristic of nuclear research reactors. Fricke gels in form of layers give the possibility of achieving spatial distribution of gamma dose, fast neutron dose and dose due to charged particles generated by thermal neutron reactions. The thermal neutron fluence has been deduced from the dose coming from the charge particles emitted by neutron reactions with the isotope 10B. Some measurements have been performed for improving the information on the relative sensitivity of Fricke gel dosimeters to the particles produced by 10B reactions, because at present the precision of dose evaluations is limited by the scanty knowledge about the dependence of the dosimeter sensitivity on the radiation LET. For in-air measurements, the dosimeter material can produce an enhancement of thermal neutron fluence. Measurements and Monte Carlo calculations have been developed to investigate the importance of this effect.

Total Reconstruction of Lower Eyelid in a Post-traumatic Patient Using Modified Fricke's Cheek Flap.

PubMed

Sengupta, Subhabrata; Baruah, Binayak; Pal, Suvra; Tuli, Isha Preet

2013-07-01

Eyelids are very complex structure, reconstruction of which is a challenge to surgeons. Reconstruction of eyelids may be required in a variety of conditions like congenital anomalies, trauma, or postsurgical excision in malignant lesions involving the eyelids. There are numerous ways to reconstruct the eyelids; the best procedure depends on both the skill of the surgeon and the condition of the patient. Fricke' lateral temporal based flap was first described in 1829 for reconstruction of the eyelids and lateral canthal region. This flap had inherent problems regarding cosmetic appearance of the eyebrows. The modified Fricke's flap based on the cheek has the advantage of avoiding such complications. It is very easy and rapid outpatient department (OPD) based procedure with acceptable cosmetic and functional result. It can be done by all ear, nose, and throat (ENT) and head and neck surgeons without any reconstructive training. In this article we are presenting a case of total reconstruction of lower eyelid using the modified Fricke's cheek flap.

Walheim, Frick, Love and Poindexter on MDDK

NASA Image and Video Library

2008-02-14

S122-E-008586 (14 Feb. 2008) --- Astronauts Rex Walheim (left), STS-122 mission specialist; Steve Frick, commander; Stanley Love, mission specialist; and Alan Poindexter, pilot, take a moment during flight day eight activities for a photo on the middeck of Space Shuttle Atlantis while docked with the International Space Station.

Melvin, Love, Frick and Walheim on MDDK

NASA Image and Video Library

2008-02-14

S122-E-008583 (14 Feb. 2008) --- Astronauts Steve Frick (second right), STS-122 commander; Leland Melvin (left), Stanley Love (top) and Rex Walheim, all mission specialists, take a moment during flight day eight activities for a photo on the middeck of Space Shuttle Atlantis while docked with the International Space Station.

Walheim, Frick, Love and Poindexter on MDDK

NASA Image and Video Library

2008-02-14

S122-E-008585 (14 Feb. 2008) --- Astronauts Rex Walheim (left), STS-122 mission specialist; Steve Frick, commander; Stanley Love, mission specialist; and Alan Poindexter, pilot, take a moment during flight day eight activities for a photo on the middeck of Space Shuttle Atlantis while docked with the International Space Station.

Study of the absorption spectra of Fricke Xylenol Orange gel dosimeters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gambarini, Grazia; Artuso, Emanuele; Liosi, Giulia Maria

2015-07-01

A systematic study of the absorption spectra of Fricke Xylenol Orange gel dosimeters has been performed, in the wavelength range from 300 nm to 700 nm. The spectrum of Xylenol Orange (without ferrous sulphate solution) has been achieved, in order to subtract its contribution from the absorption spectra of the irradiated Fricke Xylenol Orange gel dosimeters. The absorbance due to ferric ions chelated by Xylenol Orange has been studied for various irradiation doses. Two absorbance peaks are visible, mainly at low doses: the first peak increases with the dose more slowly than the second one. This effect can explain themore » apparent threshold dose that was frequently evidenced. (authors)« less

Frick, Melvin and Love in the U.S. Lab

NASA Image and Video Library

2008-02-13

S122-E-008251 (13 Feb. 2008) --- Astronauts Steve Frick (top left), STS-122 commander; Leland Melvin (bottom) and Stanley Love, both mission specialists, take a moment for a photo while working the controls of the station's robotic Canadarm2 in the Destiny laboratory of the International Space Station while Space Shuttle Atlantis is docked with the station.

The 'RITE' use of the Fricke flap in periorbital reconstruction.

PubMed

Wilcsek, G; Leatherbarrow, B; Halliwell, M; Francis, I

2005-08-01

To revisit an important but outmoded periorbital reconstructive technique. We present cases to illustrate the usefulness of the Fricke flap and describe a method of rapid intraoperative tissue expansion (RITE), which can enhance the applicability and effectiveness of the Fricke flap. A comparison between those cases performed with and without adjunctive RITE was not made due to the low numbers available. A retrospective review of clinical cases. A total of 20 cases in which the Fricke flap was used for periorbital reconstruction were reviewed. The mean patient age was 64.7 years; the male-to-female ratio was 1:1. The patient follow-up ranged from 1 to 8 years with a mean of 4.2 years. The most common cause (65%) of periorbital defect was excision of eyelid malignancy. Necrosis of the terminal segment of the flap requiring further surgical intervention occurred in 10% (2/20). In both of these cases, the surgeons were trainees, with the complications being due to poor surgical technique. In the first case, the flap base was too narrow and in the second case, the distal end of the flap was thinned excessively. The functional result was excellent in 10/20 (50%), good in 5/20 (25%), fair in 3/20 (15%), and poor in 2/20 (10%). The cosmetic result was excellent in 3/20 (15%), good in 12/20 (60%), fair in 3/20 (15%), and poor in 2/20 (10%). The Fricke flap is an important and, in selected cases, an indispensable technique in periorbital reconstruction.

Design and Calibration of a X-Ray Millibeam

DTIC Science & Technology

2005-12-01

developed for use in Fricke dosimetry , parallel-plate ionization chambers, Lithium Fluoride thermoluminescent dosimetry ( TLD ), and EBT GafChromic...thermoluminescent dosimetry ( TLD ), and EBT GafChromic film to characterize the spatial distribution and accuracy of the doses produced by the Faxitron. A...absorbed dose calibration factors for use in Fricke dosimetry , parallel-plate ionization chambers, Lithium Fluoride (LiF) TLD , and EBT GafChromic film. The

Commentary: So Was It Worth It? a Commentary on Fricke Et Al. and Hagen Et Al. (2017)

ERIC Educational Resources Information Center

McCartney, Elspeth

2017-01-01

Fricke et al. and Hagen et al. (2017) each report on large-scale pragmatic randomised controlled trials delivered in schools or nurseries, investigating language interventions for vulnerable children and showing moderate positive effect sizes. Such research is part of a recent development of 'what works' research in England, and the number of…

TH-AB-BRA-11: Using 3D Dosimeters for the Investigation of the Electron Return Effect (ERE) in MR-Guided Radiation Therapy: A Feasibility Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, G; Lee, H; Alqathami, M

Purpose: To demonstrate the capability of 3D radiochromic PRESAGE and Fricke-type dosimeters to measure the influence of magnetic fields on dose distribution, including the electron return effect (ERE), for MR-guided radiation therapy applications. Methods: Short cylindrical 3D dosimeters with PRESAGE and Fricke-type formulations were created in-house prior to irradiations in a 1.5T/7MV MR-linac. Each dosimeter was prepared with a concentric cylindrical air cavity with diameters of 1.5 cm and 2.5 cm, and the diameters of the dosimeters were 7.2 cm and 8.8 cm for PRESAGE and Fricke-type respectively. The dosimeters were irradiated within the bore of the MR-linac with themore » flat face of the dosimeters perpendicular to the magnetic field. Dosimeters were irradiated to approximately 9 Gy and 29 Gy to the center of dosimeters with a 15×15 cm{sup 2} field. The PRESAGE dosimeter was scanned using an optical-CT 2 hours post-irradiation; the Fricke-type dosimeter was immediately imaged with the MR component of the MR-linac post-irradiation. Results: Axial slices of the dose distributions show a clear demonstration of the dose enhancement due to the ERE above the cavity and the region of reduced dose below the cavity. The regions of increased and reduced dose are rotated with respect to the radiation beam axis due to the average directional change of the electrons. Measurements from line profiles show the dose enhanced up to ∼0.5 cm around the cavity by up to a factor of 1.3 and 1.4 for PRESAGE and Fricke-type dosimeters respectively. Conclusion: PRESAGE and Fricke-type dosimeters are able to qualitatively measure the ERE with good agreement with previously published simulation and 2D dosimetry demonstrations of the ERE. Further investigation of these 3D dosimeters as promising candidates for quality assurance of MR-guided radiation therapy systems is encouraged to assess changes in response and measurement accuracy due to the magnetic field.« less

SU-F-19A-02: Comparison of Absorbed Dose to Water Standards for HDR Ir-192 Brachytherapy Between the LCR, Brazil and NRC, Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salata, C; David, M; Almeida, C de

2014-06-15

Purpose: To compare absorbed dose to water standards for HDR brachytherapy dosimetry developed by the Radiological Science Laboratory of Rio de Janeiro State University (LCR) and the National Research Council, Canada (NRC). Methods: The two institutions have separately developed absorbed dose standards based on the Fricke dosimetry system. There are important differences between the two standards, including: preparation and read-out of the Fricke solution, irradiation geometry of the Fricke holder in relation to the Ir-192 source, and determination of the G-value to be used at Ir-192 energies. All measurements for both standards were made directly at the NRC laboratory (i.e.,more » no transfer instrument was used) using a single Ir-192 source (microSelectron v2). In addition, the NRC group has established a self-consistent method to determine the G-value for Ir-192, based on an interpolation between G-values obtained at Co-60 and 250kVp X-rays, and this measurement was repeated using the LCR Fricke solution to investigate possible systematic uncertainties. Results: G-values for Co-60 and 250 kVp x-rays, obtained using the LCR Fricke system, agreed with the NRC values within 0.5 % and 1 % respectively, indicating that the general assumption of universal G-values is appropriate in this case. The standard uncertainty in the determination of G for Ir-192 is estimated to be 0.6 %. For the comparison of absorbed dose measurements at the reference point for Ir-192 (1 cm depth in water, perpendicular to the seed long-axis), the ratio Dw(NRC)/Dw(LCR) was found to be 1.011 with a combined standard uncertainty of 1.7 %, k=1. Conclusion: The agreement in the absorbed dose to water values for the LCR and NRC systems is very encouraging. Combined with the lower uncertainty in this approach compared to the present air-kerma approach, these results reaffirm the use of Fricke solution as a potential primary standard for HDR Ir-192 brachytherapy.« less

The Fallacy of Quantifying Risk

DTIC Science & Technology

2012-09-01

Defense AT&L: September–October 2012 18 The Fallacy of Quantifying Risk David E. Frick, Ph.D. Frick is a 35-year veteran of the Department of...a key to risk analysis was “choosing the right technique” of quantifying risk . The weakness in this argument stems not from the assertion that one...of information about the enemy), yet achiev- ing great outcomes. Attempts at quantifying risk are not, in and of themselves, objectionable. Prudence

Love, Frick and Walheim in the A/L prior to EVA 3

NASA Image and Video Library

2008-02-15

S122-E-008897 (15 Feb. 2008) --- Astronaut Steve Frick, STS-122 commander, shares his enthusiasm and support with the two STS-122 mission specialists assigned to the mission's final spacewalk to perform work on the International Space Station. Equipped with their extravehicular mobility units (EMU) and other gear and just about ready to egress the station and begin the day's external tasks are astronauts Stanley Love (left) and Rex Walheim.

KSC-07pd3545

NASA Image and Video Library

2007-12-03

KENNEDY SPACE CENTER, FLA. -- STS-122 Commander Steve Frick seems satisfied with the landing practice session he has just completed aboard a shuttle training aircraft, or STA, at Kennedy Space Center's Shuttle Landing Facility. Frick and Pilot Alan Poindexter are preparing for the Dec. 6 launch on space shuttle Atlantis. The STA is a Grumman American Aviation-built Gulf Stream II jet that was modified to simulate an orbiter's cockpit, motion and visual cues, and handling qualities. Photo credit: NASA/Kim Shiflett

SU-D-213-06: Dosimetry of Modulated Electron Radiation Therapy Using Fricke Gel Dosimeter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gawad, M Abdel; Elgohary, M; Hassaan, M

Purpose: Modulated electron radiation therapy (MERT) has been proposed as an effective modality for treatment of superficial targets. MERT utilizes multiple beams of different energies which are intensity modulated to deliver optimized dose distribution. Energy independent dosimeters are thus needed for quantitative evaluations of MERT dose distributions and measurements of absolute doses delivered to patients. Thus in the current work we study the feasibility of Fricke gel dosimeters in MERT dosimetry. Methods: Batches of radiation sensitive Fricke gel is fabricated and poured into polymethyl methacrylate cuvettes. The samples were irradiated in solid water phantom and a thick layer of bolusmore » was used as a buildup. A spectrophotometer system was used for measuring the color changes (the absorbance) before and after irradiation and then we calculate net absorbance. We constructed calibration curves to relate the measured absorbance in terms of absorbed dose for all available electron energies. Dosimetric measurements were performed for mixed electron beam delivery and we also performed measurement for segmented field delivery with the dosimeter placed at the junction of two adjacent electron beams of different energies. Dose measured by our gel dosimetry is compared to that calculation from our precise treatment planning system. We also initiated a Monte Carlo study to evaluate the water equivalence of our dosimeters. MCBEAM and MCSIM codes were used for treatment head simulation and phantom dose calculation. PDDs and profiles were calculated for electron beams incident on a phantom designed with 1cm slab of Fricke gel. Results: The calibration curves showed no observed energy dependence with all studied electron beam energies. Good agreement was obtained between dose calculated and that obtained by gel dosimetry. Monte Carlo results illustrated the tissue equivalency of our Gel dosimeters. Conclusion: Fricke Gel dosimeters represent a good option for the dosimetric quality assurance prior to MERT application.« less

Characterization of ferrous-methylthymol blue-polyvinyl alcohol gel dosimeters using nuclear magnetic resonance and optical techniques

NASA Astrophysics Data System (ADS)

Rabaeh, Khalid A.; Eyadeh, Molham M.; Hailat, Tariq F.; Aldweri, Feras M.; Alheet, Samer M.; Eid, Rania M.

2018-07-01

A new composition of Ferrous sulphate-Metheylthymol blue (MTB)-Polyvinyl alcohol (PVA) dosimeter is introduced in this work and evaluated using nuclear magnetic resonance (NMR) and absorbance spectrophotometry techniques. The Fricke-MTB-PVA dosimeters were irradiated using a medical linear accelerator in a cubic water phantom. The dose response of the dosimeters was investigated using NMR in terms of spin-spin relaxation rate (R2), and ultraviolet and visible regions (UV-Vis) spectrophotometry in terms of absorbance. The dosimeter presents a linear dose response for doses up to 20 Gy with UV-Vis and 40 Gy with NMR method. The sample with 0.1 mM MTB, 5% PVA by weight showed highest dose sensitivity for both techniques. The Fricke-MTB-PVA dosimeter developed in this work has a significant advance over the Fricke-MTB-gelatin system: the NMR sensitivity was remarkably improved; the auto-oxidation rate was seven times lower, and no significant dose rate or photon energy effects were observed.

Integration of Fricke gel dosimetry with Ag nanoparticles for experimental dose enhancement determination in theranostics.

PubMed

Vedelago, J; Mattea, F; Valente, M

2018-03-01

The use and implementation of nanoparticles in medicine has grown exponentially in the last twenty years. Their main applications include drug delivery, theranostics, tissue engineering and magneto function. Dosimetry techniques can take advantage of inorganic nanoparticles properties and their combination with gel dosimetry techniques could be used as a first step for their later inclusion in radio-diagnostics or radiotherapy treatments. The present study presents preliminary results of properly synthesized and purified silver nanoparticles integration with Fricke gel dosimeters. Used nanoparticles presented mean sizes ranging from 2 to 20 nm, with a lognormal distribution. Xylenol orange concentration in Fricke gel dosimeter was adjust in order to allow sample's optical readout, accounting nanoparticles plasmon. Dose enhancement was assessed irradiating dosimeters setting X-ray beams energies below and above silver K-edge. Monte Carlo simulations were used to estimate the dose enhancement in the experiments and compare with the trend obtained in the experimental results. Copyright © 2018 Elsevier Ltd. All rights reserved.

Commentary: Integrating callous and unemotional traits into the definition of antisocial behaviour--a commentary on Frick et al. (2014).

PubMed

Rowe, Richard

2014-06-01

Heterogeneity in the presentation, antecedents, prognosis and treatment response of antisocial behaviour has long provided a challenge to developmental psychopathology researchers. As illustrated in the incisive Frick and colleagues' Annual Research Review, there is growing evidence that the presence of high callous-unemotional (CU) traits identifies a subgroup of antisocial young people with a particularly aggressive and pervasive form of disorder. Frick and colleagues extend their developmental psychopathology approach to CU traits by linking in theories of conscience development and considering evidence on the stability of CU traits. This commentary addresses these themes and the area more generally, considering (1) comparison of a CU specifier to alternative approaches to antisocial heterogeneity (2) high CU traits in the absence of antisocial behaviour and (3) aspects of the measurement of CU traits. © 2014 The Author. Journal of Child Psychology and Psychiatry. © 2014 Association for Child and Adolescent Mental Health.

Effect of tubing deposition, breathing pattern, and temperature on aerosol mass distribution measured by cascade impactor.

PubMed

Gurses, Burak K; Smaldone, Gerald C

2003-01-01

Aerosols produced by nebulizers are often characterized on the bench using cascade impactors. We studied the effects of connecting tubing, breathing pattern, and temperature on mass-weighted aerodynamic particle size aerosol distributions (APSD) measured by cascade impaction. Our experimental setup consisted of a piston ventilator, low-flow (1.0 L/min) cascade impactor, two commercially available nebulizers that produced large and small particles, and two "T"-shaped tubes called "Tconnector(cascade)" and "Tconnector(nebulizer)" placed above the impactor and the nebulizer, respectively. Radiolabeled normal saline was nebulized using an airtank at 50 PSIG; APSD, mass balance, and Tconnector(cascade) deposition were measured with a gamma camera and radioisotope calibrator. Flow through the circuit was defined by the air tank (standing cloud, 10 L/min) with or without a piston pump, which superimposed a sinusoidal flow on the flow from the air tank (tidal volume and frequency of breathing). Experiments were performed at room temperature and in a cooled environment. With increasing tidal volume and frequency, smaller particles entered the cascade impactor (decreasing MMAD; e.g., Misty-Neb, 4.2 +/- 0.9 microm at lowest ventilation and 2.7 +/- 0.1 microm at highest, p = 0.042). These effects were reduced in magnitude for the nebulizer that produced smaller particles (AeroTech II, MMAD 1.8 +/- 0.1 to 1.3 +/- 0.1 microm; p = 0.0044). Deposition on Tconnector(cascade) increased with ventilation but was independent of cascade impactor flow. Imaging of the Tconnector(cascade) revealed a pattern of deposition unaffected by cascade impactor flow. These measurements suggest that changes in MMAD with ventilation were not artifacts of tubing deposition in the Tconnector(cascade). At lower temperatures, APSD distributions were more polydisperse. Our data suggest that, during patient inhalation, changes in particle distribution occur that are related to conditions in the tubing and may reduce the diameters of particles entering the patient. This effect is more significant for nebulizers producing large particles. Changes in ambient temperature did not affect these observations.

KSC-08pd0985

NASA Image and Video Library

2008-04-18

CAPE CANAVERAL, Fla. -- At the luncheon held during NASA’s Future Forum in Miami, astronaut Steve Frick gives the keynote address. Frick served as commander of the STS-122 shuttle mission. The forum focused on how space exploration benefits Florida's economy. The event, which included presentations and panels, was held at the University of Miami's BankUnited Center. Among those participating were NASA Deputy Administrator Shana Dale, astronaut Carl Walz, director of the Advanced Capabilities Division in NASA's Exploration Systems Mission Directorate, and Russell Romanella, director, International Space Station and Spacecraft Processing. Photo credit: NASA/Kim Shiflett

Study of Fricke-gel dosimeter calibration for attaining precise measurements of the absorbed dose

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liosi, Giulia Maria; Benedini, Sara; Giacobbo, Francesca

2015-07-01

A method has been studied for attaining, with good precision, absolute measurements of the spatial distribution of the absorbed dose by means of the Fricke gelatin Xylenol Orange dosimetric system. With this aim, the dose response to subsequent irradiations was analyzed. In fact, the proposed modality is based on a pre-irradiation of each single dosimeter in a uniform field with a known dose, in order to extrapolate a calibration image for a subsequent non-uniform irradiation with an un-known dose to be measured. (authors)

Dose control in electron beam processing: Comparison of results from a graphite charge collector, routine dosimeters and the ISS alanine-based dosimeter

NASA Astrophysics Data System (ADS)

Fuochi, P. G.; Onori, S.; Casali, F.; Chirco, P.

1993-10-01

A 12 MeV linear accelerator is currently used for electron beam processing of power semiconductor devices for lifetime control and, on an experimental basis, for food irradiation, sludge treatment etc. In order to control the irradiation process a simple, quick and reliable method for a direct evaluation of dose and fluence in a broad electron beam has been developed. This paper presents the results obtained using a "charge collector" which measures the charge absorbed in a graphite target exposed in air. Calibration of the system with super-Fricke dosimeter and comparison of absorbed dose results obtained with plastic dosimeters and alanine pellets are discussed.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, astronaut Stephen Frick and STS-114 Mission Specialist Wendy Lawrence watch as crew members work with equipment that will be used on the mission. Frick is a tile specialist, who joined the STS-114 crew during equipment familiarization at KSC. STS-114 is classified as Logistics Flight 1 to the International Space Station, delivering new supplies and replacing one of the orbital outpost’s Control Moment Gyroscopes (CMGs). STS-114 will also carry a Raffaello Multi-Purpose Logistics Module and the External Stowage Platform-2. The crew is slated to conduct at least three spacewalks: They will demonstrate repair techniques of the Shuttle’s Thermal Protection System, replace the failed CMG with one delivered by the Shuttle, and install the External Stowage Platform.

NASA Image and Video Library

2004-01-27

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, astronaut Stephen Frick and STS-114 Mission Specialist Wendy Lawrence watch as crew members work with equipment that will be used on the mission. Frick is a tile specialist, who joined the STS-114 crew during equipment familiarization at KSC. STS-114 is classified as Logistics Flight 1 to the International Space Station, delivering new supplies and replacing one of the orbital outpost’s Control Moment Gyroscopes (CMGs). STS-114 will also carry a Raffaello Multi-Purpose Logistics Module and the External Stowage Platform-2. The crew is slated to conduct at least three spacewalks: They will demonstrate repair techniques of the Shuttle’s Thermal Protection System, replace the failed CMG with one delivered by the Shuttle, and install the External Stowage Platform.

Influence of experimental parameters on sonochemistry dosimetries: KI oxidation, Fricke reaction and H2O2 production.

PubMed

Merouani, Slimane; Hamdaoui, Oualid; Saoudi, Fethi; Chiha, Mahdi

2010-06-15

Central events of the ultrasonic action are the cavitation bubbles that can be considered as microreactors. Adiabatic collapse of cavitation bubbles leads to the formation of reactive species such as hydroxyl radicals (*OH), hydrogen peroxide (H(2)O(2)) and hydroperoxyl radicals (HOO*). Several chemical methods were used to detect the production of these reactive moieties in sonochemistry. In this work, the influence of several operational parameters on the sonochemistry dosimetries namely KI oxidation, Fricke reaction and H(2)O(2) production using 300 kHz ultrasound was investigated. The main experimental parameters showing significant effect in KI oxidation dosimetry were initial KI concentration, acoustic power and pH. The solution temperature showed restricted influence on KI oxidation. The acoustic power and liquid temperature highly affected Fricke reaction dosimetry. Operational conditions having important influence on H(2)O(2) formation were acoustic power, solution temperature and pH. For the three tested dosimetries, the sonochemical efficiency was independent of liquid volume. Copyright 2010 Elsevier B.V. All rights reserved.

STS-110 Pilot Frick in M-113 personnel carrier during TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-110 Pilot Stephen Frick waits inside the M-113 armored personnel carrier to begin training on driving the vehicle, which is part of Terminal Countdown Demonstration Test activities. TCDT includes emergency egress training and a simulated launch countdown. The TCDT is held at KSC prior to each Space Shuttle flight. Scheduled for launch April 4, the 11-day mission will feature Shuttle Atlantis docking with the International Space Station (ISS) and delivering the S0 truss, the centerpiece-segment of the primary truss structure that will eventually extend over 300 feet.

A reduction of diffusion in PVA Fricke hydrogels

NASA Astrophysics Data System (ADS)

Smith, S. T.; Masters, K. S.; Hosokawa, K.; Blinco, J.; Crowe, S. B.; Kairn, T.; Trapp, J. V.

2015-01-01

A modification to the PVA-FX hydrogel whereby the chelating agent, xylenol orange, was partially bonded to the gelling agent, poly-vinyl alcohol, resulted in an 8% reduction in the post irradiation Fe3+ diffusion, adding approximately 1 hour to the useful timespan between irradiation and readout. This xylenol orange functionalised poly-vinyl alcohol hydrogel had an OD dose sensitivity of 0.014 Gy-1 and a diffusion rate of 0.133 mm2 h-1. As this partial bond yields only incremental improvement, it is proposed that more efficient methods of bonding xylenol orange to poly-vinyl alcohol be investigated to further reduce the diffusion in Fricke gels.

KSC-08pd0982

NASA Image and Video Library

2008-04-18

CAPE CANAVERAL, Fla. -- During a break in presentations at NASA’s Future Forum in Miami, astronaut Steve Frick and former astronaut Carl Walz sign autographs. Frick served as commander of the STS-122 shuttle mission. Walz is now director of NASA’s Advanced Capabilities Division. The forum focused on how space exploration benefits Florida's economy. The event, which included presentations and panels, was held at the University of Miami's BankUnited Center. Among those participating were NASA Deputy Administrator Shana Dale, astronaut Carl Walz, director of the Advanced Capabilities Division in NASA's Exploration Systems Mission Directorate, and Russell Romanella, director, International Space Station and Spacecraft Processing. Photo credit: NASA/Kim Shiflett

Fricke S-duality in CHL models

DOE PAGES

Persson, Daniel; Volpato, Roberto

2015-12-23

In this study, we consider four dimensional CHL models with sixteen spacetime supersymmetries obtained from orbifolds of type IIA superstring on K3×T 2 by a Z N symmetry acting (possibly) non-geometrically on K3. We show that most of these models (in particular, for geometric symmetries) are self-dual under a weak-strong duality acting on the heterotic axio-dilaton modulus S by a “Fricke involution” S → -1/NS. This is a novel symmetry of CHL models that lies outside of the standard SL(2,Z)-symmetry of the parent theory, heterotic strings on T 6. For self-dual models this implies that the lattice of purely electricmore » charges is N-modular, i.e. isometric to its dual up to a rescaling of its quadratic form by N. We verify this prediction by determining the lattices of electric and magnetic charges in all relevant examples. We also calculate certain BPS-saturated couplings and verify that they are invariant under the Fricke S-duality. For CHL models that are not self-dual, the strong coupling limit is dual to type IIA compactified on T 6/Z N, for some Z N-symmetry preserving half of the spacetime supersymmetries.« less

SU-G-JeP2-04: Comparison Between Fricke-Type 3D Radiochromic Dosimeters for Real-Time Dose Distribution Measurements in MR-Guided Radiation Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, H; Alqathami, M; Wang, J

Purpose: To assess MR signal contrast for different ferrous ion compounds used in Fricke-type gel dosimeters for real-time dose measurements for MR-guided radiation therapy applications. Methods: Fricke-type gel dosimeters were prepared in 4% w/w gelatin prior to irradiation in an integrated 1.5 T MRI and 7 MV linear accelerator system (MR-Linac). 4 different ferrous ion (Fe2?) compounds (referred to as A, B, C, and D) were investigated for this study. Dosimeter D consisted of ferrous ammonium sulfate (FAS), which is conventionally used for Fricke dosimeters. Approximately half of each cylindrical dosimeter (45 mm diameter, 80 mm length) was irradiated tomore » ∼17 Gy. MR imaging during irradiation was performed with the MR-Linac using a balanced-FFE sequence of TR/TE = 5/2.4 ms. An approximate uncertainty of 5% in our dose delivery was anticipated since the MR-Linac had not yet been fully commissioned. Results: The signal intensities (SI) increased between the un-irradiated and irradiated regions by approximately 8.6%, 4.4%, 3.2%, and 4.3% after delivery of ∼2.8 Gy for dosimeters A, B, C, and D, respectively. After delivery of ∼17 Gy, the SI had increased by 24.4%, 21.0%, 3.1%, and 22.2% compared to the un-irradiated regions. The increase in SI with respect to dose was linear for dosimeters A, B, and D with slopes of 0.0164, 0.0251, and 0.0236 Gy{sup −1} (R{sup 2} = 0.92, 0.97, and 0.96), respectively. Visually, dosimeter A had the greatest optical contrast from yellow to purple in the irradiated region. Conclusion: This study demonstrated the feasibility of using Fricke-type dosimeters for real-time dose measurements with the greatest optical and MR contrast for dosimeter A. We also demonstrated the need to investigate Fe{sup 2+} compounds beyond the conventionally utilized FAS compound in order to improve the MR signal contrast in 3D dosimeters used for MR-guided radiation therapy. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship Program under Grant No. LH- 102SPS.« less

Intercomparison of standards of absorbed dose between the USSR and the UK

NASA Astrophysics Data System (ADS)

Berlyand, V. A.; Bregadze, J. I.; Burns, J. E.; Dusautoy, A. R.; Sharpe, P. H. G.

1991-05-01

A comparison of national standards of absorbed dose was carried out between the All-Union Research Institute for Physical Technical and Radiotechnical Measurements (VNIIFTRI), USSR, and the National Physical Laboratotry (NPL), UK (United Kingdom). Absorbed dose to water for cobalt 60 gamma radiation was compared by means of Fricke dosimeters and ionization chambers in 1985 and 1986. The primary standards used to derive absorbed dose to water were cavity ionization chambers at NPL and a graphite calorimeter at VNIIFTRI. The ratio of absorbed dose to water, NPL to VNIIFTRI, using Fricke dosimeters was 1.008; using ionization chambers it was 1.007. This agreement is within the estimated uncertainties of the standards and measurement methods.

The effect of mixed dopants on the stability of Fricke gel dosimeters

NASA Astrophysics Data System (ADS)

Penev, K.; Mequanint, K.

2013-06-01

Auto-oxidation and fast diffusion in Fricke gels are major drawbacks to wide-spread application of these gels in 3D dosimetry. Aiming to limit both processes, we used mixed dopants: the ferric-specific ligand xylenol orange with a ferrous-specific ligand (1,10-phenanthroline) and/or a bi-functional cross-linking agent (glyoxal). Markedly improved auto-oxidation stability was observed in the xylenol orange and phenanthroline doped gel at the expense of increased background absorbance and faster diffusion. Addition of glyoxal limited the diffusion rate and led to a partial bleaching of the gel. It is conceivable that these two new compositions may find useful practical application.

Fricke-gel dosimeter: overview of Xylenol Orange chemical behavior

NASA Astrophysics Data System (ADS)

Liosi, G. M.; Dondi, D.; Vander Griend, D. A.; Lazzaroni, S.; D'Agostino, G.; Mariani, M.

2017-11-01

The complexation between Xylenol Orange (XO) and Fe3+ ions plays a key role in Fricke-gel dosimeters for the determination of the absorbed dose via UV-vis analysis. In this study, the effect of XO and the acidity of the solution on the complexation mechanism was investigated. Moreover, starting from the results of complexation titration and Equilibrium Restricted Factor Analysis, four XO-Fe3+ complexes were identified to contribute to the absorption spectra. Based on the acquired knowledge, a new [Fe3+] vs dose calibration method is proposed. The preliminary results show a significant improvement of the sensitivity and dose threshold with respect to the commonly used Abs vs dose calibration method.

Dielectric behavior of beef meat in the 1-1500kHz range: Simulation with the Fricke/Cole-Cole model.

PubMed

Damez, Jean-Louis; Clerjon, Sylvie; Abouelkaram, Saïd; Lepetit, Jacques

2007-12-01

The electrical properties of biological tissues have been researched for many years. Impedance measurements observed with increasing frequencies are mainly attributed to changes in membrane conductivity and ion and charged-molecule mobility (mainly Na(+), K(+), CL(-) ions). Equivalent circuits with passive electrical components are frequently used as a support model for presentation and analyses of the behavior of tissues submitted to electrical fields. Fricke proposed an electrical model where the elements are resistive and capacitive. The model is composed of a resistive element (Rp) representing extracellular fluids (ECF) placed in parallel with a capacitive element (Cs) representing insulating membranes in series and a resistive element (Rs) representing intracellular fluids (ICF). This model is able to describe impedance measurements: at lower frequencies, most of the current flows around the cells without being able to penetrate them, while at higher frequencies the membranes lose their insulating properties and the current flows through both the extracellular and intracellular compartments. Since meat ageing induces structural change, particularly in membrane integrity, the insulating properties of membranes decrease, and intracellular and extracellular electrolytes mix, thus driving changes in their electrical properties. We report a method combining the Fricke and Cole-Cole models that was developed to monitor and explain tissues conductivity changes in preferential directions during beef meat ageing.

Commissioning dosimetry and in situ dose mapping of a semi-industrial Cobalt-60 gamma-irradiation facility using Fricke and Ceric-cerous dosimetry system and comparison with Monte Carlo simulation data

NASA Astrophysics Data System (ADS)

Mortuza, Md Firoz; Lepore, Luigi; Khedkar, Kalpana; Thangam, Saravanan; Nahar, Arifatun; Jamil, Hossen Mohammad; Bandi, Laxminarayan; Alam, Md Khorshed

2018-03-01

Characterization of a 90 kCi (3330 TBq), semi-industrial, cobalt-60 gamma irradiator was performed by commissioning dosimetry and in-situ dose mapping experiments with Ceric-cerous and Fricke dosimetry systems. Commissioning dosimetry was carried out to determine dose distribution pattern of absorbed dose in the irradiation cell and products. To determine maximum and minimum absorbed dose, overdose ratio and dwell time of the tote boxes, homogeneous dummy product (rice husk) with a bulk density of 0.13 g/cm3 were used in the box positions of irradiation chamber. The regions of minimum absorbed dose of the tote boxes were observed in the lower zones of middle plane and maximum absorbed doses were found in the middle position of front plane. Moreover, as a part of dose mapping, dose rates in the wall positions and some selective strategic positions were also measured to carry out multiple irradiation program simultaneously, especially for low dose research irradiation program. In most of the cases, Monte Carlo simulation data, using Monte Carlo N-Particle eXtended code version MCNPX 2.7., were found to be in congruence with experimental values obtained from Ceric-cerous and Fricke dosimetry; however, in close proximity positions from the source, the dose rate variation between chemical dosimetry and MCNP was higher than distant positions.

Theme: Serving Individuals with Disabilities.

ERIC Educational Resources Information Center

Frick, Marty; And Others

1993-01-01

Includes "Reviewing Commitment to Individuals with Disabilities" (Frick); "Modifying Laboratory Equipment" (Silletto); "Equine Facilitated Therapy" (Hoover et al.); "Horticultural Therapy" (Rees, Iverson); "How Accessible Is Your Agriculture Program? (Delks, Sillery); "Agricultural Education for…

The influence of secondary processing on the structural relaxation dynamics of fluticasone propionate.

PubMed

Depasquale, Roberto; Lee, Sau L; Saluja, Bhawana; Shur, Jagdeep; Price, Robert

2015-06-01

This study investigated the structural relaxation of micronized fluticasone propionate (FP) under different lagering conditions and its influence on aerodynamic particle size distribution (APSD) of binary and tertiary carrier-based dry powder inhaler (DPI) formulations. Micronized FP was lagered under low humidity (LH 25 C, 33% RH [relative humidity]), high humidity (HH 25°C, 75% RH) for 30, 60, and 90 days, respectively, and high temperature (HT 60°C, 44% RH) for 14 days. Physicochemical, surface interfacial properties via cohesive-adhesive balance (CAB) measurements and amorphous disorder levels of the FP samples were characterized. Particle size, surface area, and rugosity suggested minimal morphological changes of the lagered FP samples, with the exception of the 90-day HH (HH90) sample. HH90 FP samples appeared to undergo surface reconstruction with a reduction in surface rugosity. LH and HH lagering reduced the levels of amorphous content over 90-day exposure, which influenced the CAB measurements with lactose monohydrate and salmeterol xinafoate (SX). CAB analysis suggested that LH and HH lagering led to different interfacial interactions with lactose monohydrate but an increasing adhesive affinity with SX. HT lagering led to no detectable levels of the amorphous disorder, resulting in an increase in the adhesive interaction with lactose monohydrate. APSD analysis suggested that the fine particle mass of FP and SX was affected by the lagering of the FP. In conclusion, environmental conditions during the lagering of FP may have a profound effect on physicochemical and interfacial properties as well as product performance of binary and tertiary carrier-based DPI formulations.

Application of the modified chi-square ratio statistic in a stepwise procedure for cascade impactor equivalence testing.

PubMed

Weber, Benjamin; Lee, Sau L; Delvadia, Renishkumar; Lionberger, Robert; Li, Bing V; Tsong, Yi; Hochhaus, Guenther

2015-03-01

Equivalence testing of aerodynamic particle size distribution (APSD) through multi-stage cascade impactors (CIs) is important for establishing bioequivalence of orally inhaled drug products. Recent work demonstrated that the median of the modified chi-square ratio statistic (MmCSRS) is a promising metric for APSD equivalence testing of test (T) and reference (R) products as it can be applied to a reduced number of CI sites that are more relevant for lung deposition. This metric is also less sensitive to the increased variability often observed for low-deposition sites. A method to establish critical values for the MmCSRS is described here. This method considers the variability of the R product by employing a reference variance scaling approach that allows definition of critical values as a function of the observed variability of the R product. A stepwise CI equivalence test is proposed that integrates the MmCSRS as a method for comparing the relative shapes of CI profiles and incorporates statistical tests for assessing equivalence of single actuation content and impactor sized mass. This stepwise CI equivalence test was applied to 55 published CI profile scenarios, which were classified as equivalent or inequivalent by members of the Product Quality Research Institute working group (PQRI WG). The results of the stepwise CI equivalence test using a 25% difference in MmCSRS as an acceptance criterion provided the best matching with those of the PQRI WG as decisions of both methods agreed in 75% of the 55 CI profile scenarios.

To tell or not to tell? Psychopathic traits and response integrity in youth delinquency surveys.

PubMed

Laajasalo, Taina; Aronen, Eeva T; Saukkonen, Suvi; Salmi, Venla; Aaltonen, Mikko; Kivivuori, Janne

2016-04-01

Individuals with high psychopathy scores are capable of providing valid self-reports on their own personality traits, but there have been no empirical studies of the effect of psychopathic features on responding to sensitive survey questions about specific behaviours. The aim of this study is to investigate any relationship between facets of psychopathy and participants' willingness to report antisocial acts in youth delinquency surveys, controlling for demographic variables known to be associated with response integrity. In a nationally representative sample of 4,855 Finnish mainstream adolescents aged 15-16, honesty of responding was assessed through direct response integrity questions related to violence, property crime and drug use. Psychopathy was measured with the Antisocial Process Screening Device - Self Report (APSD-SR). Callous-unemotional traits and, to a lesser degree, narcissistic features were associated with a dishonest response style, although the effect size was modest. Although psychopathy does not seem to influence the capability and willingness to report personality traits accurately, it may be associated with endorsing dishonest responses to questions about specific behaviours that have possible repercussions. Our findings suggest that previously observed associations between adolescents' self-reported delinquent behaviour and psychopathic traits may be underestimations of the strength of the effects. Copyright © 2014 John Wiley & Sons, Ltd.

Diplocephalus komposchi n. sp., a new species of erigonine spider (Araneae, Linyphiidae) from Austria.

PubMed

Milasowszky, Norbert; Bauder, Julia; Hepner, Martin

2017-05-16

The erigonine cladistic analyses of Hormiga (2000) and Miller & Hormiga (2004) demonstrated unambiguous support for a sister-taxon relationship between the genera Diplocephalus and Savignia. These genera, in addition to others, are commonly placed in the Savignia-group. Although the Savignia-group is not monophyletic as it was originally circumscribed by Millidge (1977), it contains a monophyletic core of genera that has been supported in various cladistic analyses, starting with Hormiga (2000). According to the most recent phylogenetic study (Frick et al. 2010), a clade within the Savignia-group included Diplocephalus along with Araeoncus, Dicymbium, Erigonella, Glyphesis and Savignia. Frick et al. (2010) included three Diplocephalus species - cristatus, latifrons and picinus - in their cladistic analyses. While D. latifrons and D. picinus were found to be the most basal species of the Savignia-group, D. cristatus was the most distal one.

Theme: Agricultural Education and Distance Education.

ERIC Educational Resources Information Center

Murphy, Tim H.; And Others

1996-01-01

Includes "The Time Is Now" (Murphy); "Technological Solution in Search of an Instructional Problem" (Willis, Touchstone); "'Principles' of Distance Education" (Peasley); "A Star Is Born!" (Swan); "Enrichment in the Classroom" (Blume, Talbert); "Practical Applications for Distance Education Technologies in Remote and Rural Areas" (Davis, Frick);…

Free radical production by high energy shock waves--comparison with ionizing irradiation.

PubMed

Morgan, T R; Laudone, V P; Heston, W D; Zeitz, L; Fair, W R

1988-01-01

Fricke chemical dosimetry is used as an indirect measure of the free radical production of ionizing irradiation. We adapted the Fricke ferrous sulfate radiation dosimeter to examine the chemical effects of high energy shock waves. Significant free radical production was documented. The reaction was dose dependent, predictably increased by acoustic impedance, but curvilinear. A thousand shocks at 18 kilovolts induced the same free radical oxidation as 1100 rad cobalt-60 gamma ionizing irradiation, increasing to 2900 rad in the presence of an air-fluid zone of acoustic impedance. The biological effect of these free radicals was compared to that of cobalt-60 ionizing irradiation by measuring the affect on Chinese hamster cells by clonogenic assay. While cobalt-60 irradiation produced a marked decrease in clonogenic survivors, little effect was noted with high energy shock waves. This suggested that the chemical effects produced by shock waves were either absent or attenuated in the cells, or were inherently less toxic than those of ionizing irradiation.

The role of hydrogels in the radical production of the Fricke-gel-dosimeter

NASA Astrophysics Data System (ADS)

Lazzaroni, S.; Liosi, G. M.; D'Agostino, G.; Marconi, R. P.; Mariani, M.; Buttafava, A.; Dondi, D.

2018-01-01

The radiolysis mechanism of the Fricke-gel-dosimeters has been investigated in order to evaluate the role of hydrogels in the radical production. For this purpose, electron paramagnetic resonance (EPR) spectra were acquired for samples frozen and irradiated at 77 K. The analysis was performed by increasing stepwise the temperature and acquiring the EPR spectra at 120 K in order to follow the radical reaction mechanism. The comparison between aqueous- and gel- dosimeters were performed. Both gelatin from porcine skin and PVA (polyvinyl alcohol) were investigated as gel matrix. Different radical species were identified and qualitatively compared. For gel matrix, peroxyl radicals, stemming from the hydrogel, play an important role in the survival of radicals at higher temperature. Moreover, the Fe3+ EPR signal has been studied and compared with the radicals concentration. From this comparison, it is evident the increase of Fe3+ concentration is shifted toward higher temperatures with respect to the radical decay. To explain this phenomenon, the intervention of EPR silent species like peroxides is supposed.

A CASE STUDY USING THE EPA'S WATER QUALITY MODELING SYSTEM, THE WINDOWS INTERFACE FOR SIMULATING PLUMES (WISP)

EPA Science Inventory

Wisp, the Windows Interface for Simulating Plumes, is designed to be an easy-to-use windows platform program for aquatic modeling. Wisp inherits many of its capabilities from its predecessor, the DOS-based PLUMES (Baumgartner, Frick, Roberts, 1994). These capabilities have been ...

QUESTIONING THE MACH NUMBER CRITERION OR WHY TURBULENT FLOW IS COMPRESSIBLE FLOW

EPA Science Inventory

According to Frick and Sigleo (1999) turbulence is a distinct and observable physical process in which flow, which is initially one-dimensional (the stem), is converted into two-dimensional radial flow (the cap) by shear. In the stem the incompressible equations of mass and momen...

A simplified guide for charged aerosol detection of non-chromophoric compounds-Analytical method development and validation for the HPLC assay of aerosol particle size distribution for amikacin.

PubMed

Soliven, Arianne; Haidar Ahmad, Imad A; Tam, James; Kadrichu, Nani; Challoner, Pete; Markovich, Robert; Blasko, Andrei

2017-09-05

Amikacin, an aminoglycoside antibiotic lacking a UV chromophore, was developed into a drug product for delivery by inhalation. A robust method for amikacin assay analysis and aerosol particle size distribution (aPSD) determination, with comparable performance to the conventional UV detector was developed using a charged aerosol detector (CAD). The CAD approach involved more parameters for optimization than UV detection due to its sensitivity to trace impurities, non-linear response and narrow dynamic range of signal versus concentration. Through careful selection of the power transformation function value and evaporation temperature, a wider linear dynamic range, improved signal-to-noise ratio and high repeatability were obtained. The influences of mobile phase grade and glassware binding of amikacin during sample preparation were addressed. A weighed (1/X 2 ) least square regression was used for the calibration curve. The limit of quantitation (LOQ) and limit of detection (LOD) for this method were determined to be 5μg/mL and 2μg/mL, respectively. The method was validated over a concentration range of 0.05-2mg/mL. The correlation coefficient for the peak area versus concentration was 1.00 and the y-intercept was 0.2%. The recovery accuracies of triplicate preparations at 0.05, 1.0, and 2.0mg/mL were in the range of 100-101%. The relative standard deviation (S rel ) of six replicates at 1.0mg/mL was 1%, and S rel of five injections at the limit of quantitation was 4%. A robust HPLC-CAD method was developed and validated for the determination of the aPSD for amikacin. The CAD method development produced a simplified procedure with minimal variability in results during: routine operation, transfer from one instrument to another, and between different analysts. Copyright © 2017 Elsevier B.V. All rights reserved.

Identifying Stable Variants of Callous-Unemotional Traits: A Longitudinal Study of At-Risk Girls

ERIC Educational Resources Information Center

Goulter, Natalie; Kimonis, Eva R.; Hawes, Samuel W.; Stepp, Stephanie; Hipwell, Alison E.

2017-01-01

Callous-unemotional (CU) traits have proven important for designating children and adolescents showing a pattern of particularly severe, stable, and aggressive antisocial behaviors (Frick, Ray, Thornton, & Kahn, 2014). Individuals with secondary CU traits represent a subpopulation that are distinguished from those with primary CU traits by…

Ceric and ferrous dosimeters show precision for 50-5000 rad range

NASA Technical Reports Server (NTRS)

Frigerio, N. A.; Henry, V. D.

1968-01-01

Ammonium thiocyanate, added to the usual ferrous sulfate dosimeter solution, yielded a very stable, precise and temperature-independent system eight times as sensitive as the classical Fricke system in the 50 to 5000 rad range. The ceric dosimeters, promising for use in mixed radiation fields, respond nearly independently of LET.

Very Low Frequency Seismo-Acoustic Noise Below the Sea Floor (0.2-10 Hz).

DTIC Science & Technology

1994-02-01

applications see Stoffa et al., 1981 and Kappus et al., 1990). Fricke (1991, 1993) outlines a method for calculating the Radon transform on "ser...of Ocean Eng., OE-6, 50-58, 1981. Kappus , M. E. , A. J. Harding, and J. A. Orcutt, A comparison of tau-p transforms methods, Geophysics, 55, 1202

MU06-857, a Green Leaf Lettuce Breeding Line with Resistance to Leafminer and Lettuce Mosaic Virus.

USDA-ARS?s Scientific Manuscript database

The Agricultural Research Service, United States Department of Agriculture announces the release of a breeding line of green leaf lettuce (Lactuca sativa L.) with resistance to leafminers (Liriomyza langei Frick) and lettuce mosaic. The line MU06-857 is similar to cultivar ‘Lolla Rossa’ (‘Lollo Ros...

ARC-1969-M-469

NASA Image and Video Library

1940-06-30

Ames Personnel in front of construction shack FRONT: ER Sharp, CF Frick, JF Parsons, E York, R Pippin, M Nettle, M G Poole, C Bioletti CENTER: R Clark, G Bulifant, J Delaney H. Allen, J. White, H. Houston, W. Walker, M. Green BACK: E. W. Betts. W.G.. Vincenti, H Kirschbaum, A.B. Follman, F. Nickle, E.C.. Briag, P. Prizler

The Antiaircraft Journal. Volume 95, Number 2, March-April 1952

DTIC Science & Technology

1952-04-01

Command, Yoko- hama. Breuning, E. G., Far East Command, Yoko- hama Cacchiotti, Ralph R., 31st AAA Brig., Ft Lewis, Wash. Colbert , Edward F., 197th AAA Gp...Wilbur B., 47th AAA Brig., Cp Stew- art, Ga. Frick, Edwin J., 336th AAA Gun Bn, Cp Ed- wards. Mass. Gildon, Milo E., USA Alaska, Fort Richard- son

The nature of the interest construct and its utility in the study of leisure behavior

Treesearch

Ellen B. Drogin Rodgers; Brenda P. Wiggins

2003-01-01

The intent of this paper is to initiate discussion regarding the nature of the interest construct. Interest influences "what people attend to, think about, discuss and learn more about" (Frick, 1992) and has been used pervasively in many disciplines as a means of explaining concepts as varied as career choice, motivation, enjoyment, learning and academic...

Cerium nanoparticle effect on sensitivity of Fricke gel dosimeter: Initial investigation

NASA Astrophysics Data System (ADS)

Ebenezer Suman Babu, S.; Peace Balasingh, S. Timothy; Benedicta Pearlin, R.; Rabi Raja Singh, I.; Ravindran, B. Paul

2017-05-01

Fricke gel dosimeters (FXGs) have been the preferred dosimeters because of its ease in preparation and water and tissue equivalency. Visible changes happen three dimensionally in the dosimeter as the ferrous (Fe2+) ions change into ferric (Fe3+) ions upon irradiation and the measure of this change can be correlated to the dose absorbed. Nanoparticles are promising entities that can improve the sensitivity of the gel dosimeter. Cerium Oxide nanoparticle was investigated for possible enhancement of absorbed dose in the FXG. Various concentrations of the nanoparticle based gel dosimeters were prepared and irradiated for a clinical dose range of 0-3 Gy in a telegamma unit. The optimal concentration of 0.1 mM nanoparticle incorporated in the FXG enhances the radiation sensitivity of the unmodified FXG taken as reference without modifying the background absorbance prior to irradiation. The gel recipe consisted of 5% (wt) gelatin, 50 mM Sulphuric acid, 0.05 mM Xylenol Orange, 0.5 mM Ferrous Ammonium Sulphate and 0.1 mM Cerium (IV) Oxide nanoparticle (< 25 nm particle size) and triple distilled water. The FXGs with nanoparticle showed linear dose response in the dose range tested.

Neutron dose estimation in a zero power nuclear reactor

NASA Astrophysics Data System (ADS)

Triviño, S.; Vedelago, J.; Cantargi, F.; Keil, W.; Figueroa, R.; Mattea, F.; Chautemps, A.; Santibañez, M.; Valente, M.

2016-10-01

This work presents the characterization and contribution of neutron and gamma components to the absorbed dose in a zero power nuclear reactor. A dosimetric method based on Fricke gel was implemented to evaluate the separation between dose components in the mixed field. The validation of this proposed method was performed by means of direct measurements of neutron flux in different positions using Au and Mg-Ni activation foils. Monte Carlo simulations were conversely performed using the MCNP main code with a dedicated subroutine to incorporate the exact complete geometry of the nuclear reactor facility. Once nuclear fuel elements were defined, the simulations computed the different contributions to the absorbed dose in specific positions inside the core. Thermal/epithermal contributions of absorbed dose were assessed by means of Fricke gel dosimetry using different isotopic compositions aimed at modifying the sensitivity of the dosimeter for specific dose components. Clear distinctions between gamma and neutron capture dose were obtained. Both Monte Carlo simulations and experimental results provided reliable estimations about neutron flux rate as well as dose rate during the reactor operation. Simulations and experimental results are in good agreement in every positions measured and simulated in the core.

IEEE Conference Record of 1976 Twelfth Modulator Symposium, New York City, 4-5 February 1976.

DTIC Science & Technology

1976-01-01

itches; ig Power Switches for Intermittent Operation; High Power M’ dulators for Intermittent Operation; Charging Systems; Circuit Techniques; Line Type... INTERMITTENT OPERATION Adiabatic Mode Operation Of Thyratrons For Megawatt Average Power Applications, John E. Creedon. Joseph W. McGowan. Anthon J...142 The SPS Fast Pulsed Magnet Systems. P. F Faugeras. E. Frick, C. G. Harrison, H. Kuhn

I Thought Composition Was about Commas and Quotes, Not Queers: Diversity and Campus Change at a Rural Two-Year College

ERIC Educational Resources Information Center

Mitchell, Danielle

2008-01-01

Fayette County, once home to the Carnegies, the Mellons, and the Fricks, now punctuated by abandoned mines and coke ovens, is the second poorest county in Pennsylvania. Gay and lesbian students experience discrimination in this County. In this article, the author discusses her efforts to intervene in this complicated problem by deploying a…

Assessing the Affective Features of Psychopathy in Adolescence: A Further Validation of the Inventory of Callous and Unemotional Traits

ERIC Educational Resources Information Center

Roose, Annelore; Bijttebier, Patricia; Decoene, Stefaan; Claes, Laurence; Frick, Paul J.

2010-01-01

To provide an extended assessment of the affective features of psychopathy, Frick developed the Inventory of Callous and Unemotional Traits (ICU), which is a multi-informant questionnaire. Previous studies have provided initial support for the self-report version. The aim of the present study is to investigate the validity of self- as well as…

OXIDATION YIELD IN FRICKE DOSIMETRY OF P$sup 32$ BETA RADIATION (in Portuguese)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baptista, A.M.; da Silva, J.G.

1962-05-01

A determination was made of the G-value, the number of ions formed by the absorption of 100 ev of energy, in the ferrous sulfate dosimetry of P/sup 32/ beta particles. The value obtained was: G = 15.6 plus or minus 0.07. A discussion is included of the errors which may possibly affect the results. (tr- auth)

The Influence of Teacher-Student Conflict on Teacher Ratings of Children's Externalizing and Internalizing Behaviors: A Multitrait-Multimethod Factor Analytic Approach

ERIC Educational Resources Information Center

Wickerd, Garry Dean

2012-01-01

Teachers' ratings of problem behaviors are gathered as a matter of course in psychological evaluations of children. Teacher ratings are weighted heavily in the results of educational evaluations (Frick et al., 2010). With such heavy emphasis on teacher behavioral ratings, it is important to understand the extent to which conflict between…

STS-110 crewmembers pose for photos in the Zvezda SM during Expedition Four

NASA Image and Video Library

2002-04-16

ISS004-E-10098 (16 April 2002) --- Astronaut Stephen N. Frick, STS-110 pilot, photographs crewmates in the Zvezda Service Module on the International Space Station (ISS). From the left are astronauts Michael J. Bloomfield, STS-110 mission commander, Jerry L. Ross and Lee M. E. Morin, both mission specialists. Astronaut Steven L. Smith, STS-110 mission specialist, floats above.

Pharmacological and Behavioral Enhancement of Neuroplasticity in the MPTP-Lesioned Mouse and Nonhuman Primate

DTIC Science & Technology

2008-05-01

effect of amphetamine in mice neonatally lesioned with 6- hydroxydopamine. J Neurosci Res. 78, 289-96. 22 Berger-Sweeney, J., Stearns, N. A., Frick...through its effect on pre- and post- synaptic dopamine biosynthesis, uptake and receptor expression as well as glutamatergic synapses. This hypothesis...These studies were designed to be complementary in that both non-pharmacological and pharmacological effects of neuroplasticity are being

POST - A New Look at Stratocumulus

DTIC Science & Technology

2010-07-01

1 10.1 POST - A New Look at Stratocumulus H. Gerber , G. Frick , S. P. Malinowski , W . Kumula , S...interesting to note that another flight shows entirely different behavior: Malinowski et al (2010) finds positive T’ in LW C holes near cloud top in...parameterization will also rely on ongoing analysis by POST colleagues described in Malinowski et al (2010), Hill et al (2010), W ang, Q., et al (2010), and W ang

Technical Note: Preliminary investigations into the use of a functionalised polymer to reduce diffusion in Fricke gel dosimeters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, S. T., E-mail: s164.smith@qut.edu.au; Masters, K.-S.; Hosokawa, K.

2015-12-15

Purpose: A modification of the existing PVA-FX hydrogel has been made to investigate the use of a functionalised polymer in a Fricke gel dosimetry system to decrease Fe{sup 3+} diffusion. Methods: The chelating agent, xylenol orange, was chemically bonded to the gelling agent, polyvinyl alcohol (PVA) to create xylenol orange functionalised PVA (XO-PVA). A gel was created from the XO-PVA (20% w/v) with ferrous sulfate (0.4 mM) and sulfuric acid (50 mM). Results: This resulted in an optical density dose sensitivity of 0.014 Gy{sup −1}, an auto-oxidation rate of 0.0005 h{sup −1}, and a diffusion rate of 0.129 mm{sup 2}more » h{sup −1}; an 8% reduction compared to the original PVA-FX gel, which in practical terms adds approximately 1 h to the time span between irradiation and accurate read-out. Conclusions: Because this initial method of chemically bonding xylenol orange to polyvinyl alcohol has inherently low conversion, the improvement on existing gel systems is minimal when compared to the drawbacks. More efficient methods of functionalising polyvinyl alcohol with xylenol orange must be developed for this system to gain clinical relevance.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonnelli, E.; Diniz, R.; Dos Santos, A.

The presented work shows the preliminary results of an experimental procedure to overcome the helium-3 detectors shortage in the IPEN/MB-01 nuclear reactor and be feasible the study of the high subcritical states with less sensitivity detectors. The main principle was employing the input logic nuclear module which was possible to execute logic operations with the neutron signals. Though these signals was possible to construct the Auto Power Spectral Densities (APSD) and obtain the Prompt Neutron Constant Decay (α). Two different kinds of thermal neutron detectors were used ({sup 3}He and BF{sub 3}). The arrangement was initially constituted by one ofmore » each type detector and, posteriorly, for a more complete data acquisition, in groups of two detectors for all subcritical configurations. The experiment was carried out using the control banks (BC-1 and BC-2) insertion to achieve all the subcritical states studied in this work. (authors)« less

[Construction-cost assessment of a program designed to promote physical and sports activities and prevent doping behaviors: PN-APSD - on 2002-2007].

PubMed

Bérard, A; Bréchat, P-H; Rymer, R; Londsdorfer, J

2009-02-01

According to the framework legislation promulgated as part of the reform of finance laws in France, quality is a mandatory feature of all governmental actions. In this context, this work was conducted to assess the construction cost of a national health program designed to promote physical and sports activities and prevent doping behaviors. This program was considered to have the characteristic features of a successful governmental health intervention. Four cost categories were evaluated: cost of the activity itself, transportation costs, communication costs and promotion costs. It was found that the program costs for 2002-2007 were 100,000 euro, with 15% of the costs in the communication category. Economic elements could be associated with factors of successful health service interventions in order to help decision makers responsible for the public interest and the consistency of public health actions.

SU-F-BRA-10: Fricke Dosimetry: Determination of the G-Value for Ir-192 Energy Based On the NRC Methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salata, C; David, M; Rosado, P

Purpose: Use the methodology developed by the National Research Council Canada (NRC), for Fricke Dosimetry, to determine the G-value used at Ir-192 energies. Methods: In this study the Radiology Science Laboratory of Rio de Janeiro State University (LCR),based the G-value determination on the NRC method, using polyethylene bags. Briefly, this method consists of interpolating the G-values calculated for Co-60 and 250 kV x-rays for the average energy of Ir-192 (380 keV). As the Co-60 G-value is well described at literature, and associated with low uncertainties, it wasn’t measured in this present study. The G-values for 150 kV (Effective energy ofmore » 68 keV), 250 kV (Effective energy of 132 keV)and 300 kV(Effective energy of 159 keV)were calculated using the air kerma given by a calibrated ion chamber, and making it equivalent to the absorbed to the Fricke solution, using a Monte Carlo calculated factor for this conversion. Instead of interpolations, as described by the NRC, we displayed the G-values points in a graph, and used the line equation to determine the G- value for Ir-192 (380 keV). Results: The measured G-values were 1.436 ± 0.002 µmol/J for 150 kV, 1.472 ± 0.002 µmol/J for 250 kV, 1.497 ± 0.003 µmol/J for 300 kV. The used G-value for Co-60 (1.25 MeV) was 1,613 µmol/J. The R-square of the fitted regression line among those G-value points was 0.991. Using the line equation, the calculate G-value for 380 KeV was 1.542 µmol/J. Conclusion: The Result found for Ir-192 G-value is 3,1% different (lower) from the NRC value. But it agrees with previous literature results, using different methodologies to calculate this parameter. We will continue this experiment measuring the G-value for Co-60 in order to compare with the NRC method and better understand the reasons for the found differences.« less

KSC-07pd3546

NASA Image and Video Library

2007-12-03

KENNEDY SPACE CENTER, FLA. -- STS-122 Pilot Alan Poindexter seems satisfied with the landing practice session he has just completed aboard a shuttle training aircraft, or STA, at Kennedy Space Center's Shuttle Landing Facility. Poindexter and Commander Steve Frick are preparing for the Dec. 6 launch on space shuttle Atlantis. The STA is a Grumman American Aviation-built Gulf Stream II jet that was modified to simulate an orbiter's cockpit, motion and visual cues, and handling qualities. Photo credit: NASA/Kim Shiflett

KSC-08pd0413

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- The STS-122 crew discusses its mission at a post-landing conference. Seen here, from left, are Commander Steve Frick, Pilot Alan Poindexter and Mission Specialist Leland Melvin.lists Leland Melvin, Rex Walheim, Hans Schlegel and Stanley Love. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST on Runway 15 at NASA's Kennedy Space Center. Photo credit: NASA/Jack Pfaller

KSC-02pp0020

NASA Image and Video Library

2001-12-01

JOHNSON SPACE CENTER, HOUSTON, TEXAS. -- STS-110 CREW PORTRAIT -- (JSC STS110-5-002) -- These seven astronauts are in training for the STS-110 mission, scheduled to visit the International Space Station early next year. In front, from the left, are astronauts Stephen N. Frick, pilot; Ellen Ochoa, flight engineer; and Michael J. Bloomfield, mission commander; in the back, from left, are astronauts Steven L. Smith, Rex J. Walheim, Jerry L. Ross and Lee M.E. Morin, all mission specialists

Aircraft Observations for Improved Physical Parameterization for Seasonal Prediction

DTIC Science & Technology

2013-09-30

platform is ready for use in air-sea interaction research projects. RELATED PROJECTS None PUBLICATIONS Gerber H., G. Frick, S. Malinowski ... Malinowski , S. P., H. Gerber, I. Jen-LaPlante, M. K. Kopec, W. Kumala, K. Nurowska, P. Y. Chuang, K. E. Haman, D. D. Khelif, S. K. Krueger, and H. H. Jonsson...Haman, K. E., Kopec, M. K., Khelif, D., and Malinowski , S. P.: Modified ultrafast thermometer UFT-M and temperature measurements during Physics of

Stable isotope distribution in continental Maastrichtian vertebrates from the Haţeg Basin, South Carpathians

NASA Astrophysics Data System (ADS)

Bojar, Ana-Voica; Csiki, Zoltan; Grigorescu, Dan

2010-05-01

The oxygen isotopic compositions of biogenic apatite from crocodiles, turtles and dinosaurs, and their relationship to climate and physiology have been evidenced by several studies (Barrick and Showers, 1995; Kolodny et al., 1996; Barrick et al., 1999; Fricke and Rogers, 2000; Stoskopf et al., 2001; Straight et al., 2004; Amiot et al., 2007). To date, few attempts have been made to correlate the enamel d13C to dietary resources of dinosaurs (Bocherens et al., 1988; Stanton Thomas and Carlson, 2004; Fricke and Pearson, 2008; Fricke, et al., 2008). One additional complication is that for dinosaurs, the d18O of enamel phosphate depends on both body water and variations in body temperature. Several studies addressed the issue of endothermy vs. ectothermy of fossil vertebrates by studying inter- and intra-bone and enamel isotopic variability (Barrick and Showers, 1994, 1995; Barrick et al., 1996; 1998; Fricke and Rogers, 2000). More recent investigations provided evidence for inter-tooth temporal variations and related them to seasonality and/or changes in physiology (Straight et al., 2004; Stanton Thomas and Carlson, 2004). The main objectives of this study are to extract palaeoclimatic information considering, beside lithofacial characteristics and the isotopic distribution of carbonates formed in paleosols, the stable isotope composition of vertebrate remains from the Haţeg Basin. We also sampled several teeth along their growth axis in order to get further information about growth rates and the amplitude of isotopic variation. Located in the South Carpathians in Romania, the Haţeg Basin contains a thick sequence of Maastrichtian continental deposits yielding a rich dinosaur and mammalian fauna. Stable isotope analyses of both calcretes and dinosaur, crocodilian and turtle remains from two localities (Tuştea and Sibişel) were integrated in order to reconstruct environmental conditions during the Maastrichtian time and to gain further insights into the metabolism and behaviour of the vertebrates. The large difference observed between the delta 18O and delta 13C of the eggshells and the surrounding mudstones, as well as the preservation of the 9 ‰ difference between the oxygen isotope composition of the Telmatosaurus eggshell and tooth enamel, indicate that diagenesis have not significantly altered the primary isotopic signal. Stable isotope compositions of both calcretes and phosphatic remains suggest warmer conditions during the deposition of the Tuştea sequence than during the deposition of the Sibişel sequence. The intra-tooth delta 18O patterns for Zalmoxes and Allodaposuchus show different magnitudes of isotopic variation, with lower values for Tuştea and higher for Sibişel. The calculated delta 18O body water enrichment for Kallokibotion bajazidi is similar to that found in the living turtle taxa. By contrast, in the case of Allodaposuchus, the isotopic enrichment is higher than for recent taxa. This suggests that, for Allodaposuchus, the body water was less buffered by a watery environment, which probably indicates more time spent outside water (i.e. more terrestrial habit). The delta 18O values for the teeth of Telmatosaurus and Zalmoxes are similar to those of Allodaposuchus, suggesting that, at the investigated sites, the body temperature of both dinosaurs was similar to that of the crocodile. The isotopic composition of calcretes, teeth and eggshells indicates a C3 vegetation and diet with delta 13C values between -27 to -29 ‰ (PDB) and the absence of large-scale habitat partitioning between the dinosaurs.

Advancements in internationally accepted standards for radiation processing

NASA Astrophysics Data System (ADS)

Farrar, Harry; Derr, Donald D.; Vehar, David W.

1993-10-01

Three subcommittees of the American Society for Testing and Materials (ASTM) are developing standards on various aspects of radiation processing. Subcommittee E10.01 "Dosimetry for Radiation Processing" has published 9 standards on how to select and calibrate dosimeters, where to put them, how many to use, and how to use individual types of dosimeter systems. The group is also developing standards on how to use gamma, electron beam, and x-ray facilities for radiation processing, and a standard on how to treat dose uncertainties. Efforts are underway to promote inclusion of these standards into procedures now being developed by government agencies and by international groups such as the United Nations' International Consultative Group on Food Irradiation (ICGFI) in order to harmonize regulations and help avoid trade barriers. Subcommittee F10.10 "Food Processing and Packaging" has completed standards on good irradiation practices for meat and poultry and for fresh fruits, and is developing similar standards for the irradiation of seafood and spices. These food-related standards are based on practices previously published by ICGFI. Subcommittee E10.07 on "Radiation Dosimetry for Radiation Effects on Materials and Devices" principally develops standards for determining doses for radiation hardness testing of electronics. Some, including their standards on the Fricke and TLD dosimetry systems are equally useful in other radiation processing applications.

STS-132/ULF4 WFCR Flight Controllers on Console

NASA Image and Video Library

2010-05-14

JSC2010-E-080410 (14 May 2010) --- Astronauts Steve Frick (standing) and Charles Hobaugh, both spacecraft communicators (CAPCOM) for the STS-132 mission, are pictured in the space shuttle flight control room in the Johnson Space Center's Mission Control Center during launch countdown activities a few hundred miles away in Florida, site of space shuttle Atlantis? STS-132 launch. Liftoff was on time at 2:20 p.m. (EDT) on May 14, 2010 from launch pad 39A at NASA's Kennedy Space Center.

Analytical determination of thermal conductivity of W-UO2 and W-UN CERMET nuclear fuels

NASA Astrophysics Data System (ADS)

Webb, Jonathan A.; Charit, Indrajit

2012-08-01

The thermal conductivity of tungsten based CERMET fuels containing UO2 and UN fuel particles are determined as a function of particle geometry, stabilizer fraction and fuel-volume fraction, by using a combination of an analytical approach and experimental data collected from literature. Thermal conductivity is estimated using the Bruggeman-Fricke model. This study demonstrates that thermal conductivities of various CERMET fuels can be analytically predicted to values that are very close to the experimentally determined ones.

KSC-08pd0192

NASA Image and Video Library

2008-02-07

KENNEDY SPACE CENTER, FLA. -- Commander Steve Frick is happy to be suiting up for launch of space shuttle Atlantis on the STS-122 mission. The launch, scheduled for 2:45 p.m. EST, will be the third attempt for Atlantis since December 2007 to carry the European Space Agency's Columbus laboratory to the International Space Station. During the 11-day mission, the crew's prime objective is to attach the laboratory to the Harmony module, adding to the station's size and capabilities. Photo credit: NASA/Kim Shiflett

Space Station Crew Marks the 10th Anniversary of the Launching of the European Columbus Module

NASA Image and Video Library

2018-02-07

Aboard the International Space Station, Expedition 54 Flight Engineers Joe Acaba and Mark Vande Hei of NASA took time to commemorate the 10th anniversary of the launching of the European Columbus module during an in-flight event Feb. 7 with European Space Agency officials gathered in Noordwijk, Netherlands. The Columbus science laboratory was launched on Feb. 7, 2008 aboard the space shuttle Atlantis on the STS-122 mission commanded by former NASA astronaut Stephen Frick.

U.S. Stabilization and Reconstruction Doctrine: A Failure to Address the Specifics of Authoritarian Regime Transition

DTIC Science & Technology

2009-12-03

A. Frick U.S. Army School of Advanced Military Studies United States Army Command and General Staff College Fort Leavenworth, Kansas AY 2009...involvement. The expansion of free markets , the advent of two world wars and the rise of communism shifted U.S. policy to a focus on global leadership...improvements in technology and the expansion of free markets . Free markets , a principle of classical liberalism, slowly pushed America into the global realm

U.S. Stabilization and Reconstruction Doctrine: A Failure to Address the Specifics of Authoritarian Regime Transition

DTIC Science & Technology

2009-05-21

A. Frick U.S. Army School of Advanced Military Studies United States Army Command and General Staff College Fort Leavenworth, Kansas AY 2009...involvement. The expansion of free markets , the advent of two world wars and the rise of communism shifted U.S. policy to a focus on global leadership...improvements in technology and the expansion of free markets . Free markets , a principle of classical liberalism, slowly pushed America into the global realm

KSC-08pd0415

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- The STS-122 crew discusses its mission at a post-landing conference. Moderating at left is NASA Public Affairs Officer George Diller. The crewmembers, from left, are Commander Steve Frick, Pilot Alan Poindexter and Mission Specialists Leland Melvin, Rex Walheim, Hans Schlegel and Stanley Love. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST on Runway 15 at NASA's Kennedy Space Center. Photo credit: NASA/Jack Pfaller

KSC-08pd0412

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- The STS-122 crew discusses its mission at a post-landing conference. Moderating at left is NASA Public Affairs Officer George Diller. The crewmembers, from left, are Commander Steve Frick, Pilot Alan Poindexter and Mission Specialists Leland Melvin, Rex Walheim, Hans Schlegel and Stanley Love. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST on Runway 15 at NASA's Kennedy Space Center. Photo credit: NASA/Jack Pfaller

KSC-08pd0416

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- The STS-122 crew discusses its mission at a post-landing conference. Moderating at left is NASA Public Affairs Officer George Diller. The crewmembers, from left, are Commander Steve Frick, Pilot Alan Poindexter and Mission Specialists Leland Melvin, Rex Walheim, Hans Schlegel and Stanley Love. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST on Runway 15 at NASA's Kennedy Space Center. Photo credit: NASA/Jack Pfaller

[Evaluation (assessment) of three tests for diagnosis of geohelmints in Colombia].

PubMed

López, Myriam Consuelo; Moncada, Ligia Inés; Ariza-Araújo, Yoseth; Fernández-Niño, Julián Alfredo; Reyes, Patricia; Nicholls, Rubén Santiago

2013-01-01

Soil-transmitted helminth infections are considered a public health problem in developing countries. The diagnostic tests, both for individual parient diagnosis as for population studies should be evaluated in terms of validity and reliability. To compare the direct examination, the modified Ritchie-Frick method, a Kato-Katz designed by a Brazilian group and one designed by the WHO, for the diagnosis of soil-transmitted helminthes. A diagnostic test reliability study was performed. The same stool sample was analyzed by the same observer using four diagnostic tests. 204 samples were obtained, 194 of those fulfilled the inclusion criteria and were analyzed. The observers did not know the participants' identity neither the other tests results. For the analysis the Kato-Katz (WHO) was considered as the gold standard. For the reliability assessment percent agreement, positive percent agreement, Kappa statistic, and intraclass correlation were performed. The Brazilian Kato-Katz showed a good performance with high sensitivity and specificity for T. trichiura and Hookworm with values of 0.97 and 0.96 respectively, and a high specificity with mild sensitivity for A. lumbricoides (0.95 and 0.79) meanwhile the direct examination and the Ritche-Frick method showed a performance between mild and poor. The differences were higher for hookworm and Trichiuris trichiura than for Ascaris lumbricoides. The Brazilian Kato Katz test could be implemented, but further studies are needed to correlate its operative capacity with its feasibility, availability and cost.

The Role of Polycomb Group Gene BMI-1 in the Development of Prostate Cancer

DTIC Science & Technology

2009-09-01

17. Fu M, Wang C, Li Z, Sakamaki T, Pestell RG. Minireview: Cyclin D1: normal and abnormal functions. Endocrinology. 2004 Dec;145(12):5439-47. 18...connecting development to breast cancer. Cell Cycle. 2004 Feb;3(2):145-8. 32. Wang C, Li Z, Fu M, Bouras T, Pestell RG. Signal transduction mediated by...Ferzli G, Johnson K, Fricke S, Diba F, Kallakury B, Ohanyerenwa C, Chen M, Ostrowski M, Hung MC, Rabbani SA, Datar R, Cote R, Pestell R, Albanese C

First Integrated Flight Simulation For STS 114

NASA Image and Video Library

2004-10-13

JSC2004-E-45138 (13 October 2004) --- Astronaut Stephen N. Frick monitors communications at the spacecraft communicator (CAPCOM) console in the Shuttle Flight Control Room (WFCR) in Johnson Space Center’s (JSC) Mission Control Center (MCC) with the STS-114 crewmembers during a fully-integrated simulation on October 13. The seven member crew was in a JSC-based simulator during the sims. The dress rehearsal of Discovery's rendezvous and docking with the International Space Station (ISS) was the first flight-specific training for the Space Shuttle's return to flight.

Shuttle Atlantis on approach for docking to the ISS during STS-110 and Expedition Four

NASA Image and Video Library

2002-04-10

ISS004-E-9944 (10 April 2002) --- The Space Shuttle Atlantis prepares to dock with the International Space Station (ISS) during the STS-110 mission. Aboard Atlantis are astronauts Michael J. Bloomfield, mission commander; Stephen N. Frick, pilot; Rex J. Walheim, Ellen Ochoa, Lee M. E. Morin, Jerry L. Ross, and Steven L. Smith, all mission specialists. The STS-110 crewmembers are delivering the S0 (S-zero) truss, which is visible in Atlantis’ payload bay. This image was taken by an Expedition Four crewmember.

STS-110 M.S. Ochoa in M-113 personnel carrier during TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- STS-110 Mission Specialist Ellen Ochoa waits her turn at driving the M-113 armored personnel carrier, part of Terminal Countdown Demonstration Test activities. In the background, right, is Pilot Stephen Frick. TCDT includes emergency egress training and a simulated launch countdown. The TCDT is held at KSC prior to each Space Shuttle flight. Scheduled for launch April 4, the 11-day mission will feature Shuttle Atlantis docking with the International Space Station (ISS) and delivering the S0 truss, the centerpiece-segment of the primary truss structure that will eventually extend over 300 feet.

Crewmembers share a meal in the SM

NASA Image and Video Library

2008-02-10

S122-E-007054 (9 Feb. 2008) --- Not long after the hatches were opened on the International Space Station and STS-122 crewmembers were able to come onboard, eating utensils were brought out as nine astronauts and a cosmonaut shared a meal time. From the left foreground are astronauts Rex Walheim, Daniel Tani, Steve Frick and Alan Poindexter. Cosmonaut Yuri Malenchenko is in the background. Tani and Malenchenko are members of the Expedition 16 crew, but Tani's time in that position is short as he soon will be switching out duties with ESA astronaut Leopold Eyharts (out of frame).

STS-122 crew portrait

NASA Image and Video Library

2006-07-21

STS122-S-002 (24 April 2007) --- These seven astronauts take a break from training to pose for the STS-122 crew portrait. From the left (front row) are astronauts Stephen N. Frick, commander; European Space Agency's (ESA) Leopold Eyharts; and Alan G. Poindexter, pilot. From the left (back row) are astronauts Leland D. Melvin, Rex J. Walheim, Stanley G. Love and European Space Agency's (ESA) Hans Schlegel, all mission specialists. Eyharts will join Expedition 16 in progress to serve as a flight engineer aboard the International Space Station. The crewmembers are attired in training versions of their shuttle launch and entry suits.

KSC-07pd3279

NASA Image and Video Library

2007-04-24

KENNEDY SPACE CENTER, FLA. -- STS122-S-002 -- These seven astronauts take a break from training to pose for the STS-122 crew portrait. From the left (front row) are astronauts Stephen N. Frick, commander; the European Space Agency's, or ESA's, Leopold Eyharts; and Alan G. Poindexter, pilot. From the left (back row) are astronauts Leland D. Melvin, Rex J. Walheim, Stanley G. Love and ESA's Hans Schlegel, all mission specialists. Eyharts will join Expedition 16 in progress to serve as a flight engineer aboard the International Space Station. The crewmembers are attired in training versions of their shuttle launch and entry suits.

International Space Station (ISS)

NASA Image and Video Library

2001-12-01

This is the official STS-110 crew portrait. In front, from the left, are astronauts Stephen N. Frick, pilot; Ellen Ochoa, flight engineer; and Michael J. Bloomfield, mission commander; In the back, from left, are astronauts Steven L. Smith, Rex J. Walheim, Jerry L. Ross and Lee M.E. Morin, all mission specialists. Launched aboard the Space Shuttle Orbiter Atlantis on April 8, 2002, the STS-110 mission crew prepared the International Space Station (ISS) for future space walks by installing and outfitting a 43-foot-long Starboard side S0 truss and preparing the Mobile Transporter. The mission served as the 8th ISS assembly flight.

Combination of five diagnostic tests to estimate the prevalence of hookworm infection among school-aged children from a rural area of colombia.

PubMed

Barreto, Rafael E; Narváez, Javier; Sepúlveda, Natalia A; Velásquez, Fabián C; Díaz, Sandra C; López, Myriam Consuelo; Reyes, Patricia; Moncada, Ligia I

2017-09-01

Public health programs for the control of soil-transmitted helminthiases require valid diagnostic tests for surveillance and parasitic control evaluation. However, there is currently no agreement about what test should be used as a gold standard for the diagnosis of hookworm infection. Still, in presence of concurrent data for multiple tests it is possible to use statistical models to estimate measures of test performance and prevalence. The aim of this study was to estimate the diagnostic accuracy of five parallel tests (direct microscopic examination, Kato-Katz, Harada-Mori, modified Ritchie-Frick, and culture in agar plate) to detect hookworm infections in a sample of school-aged children from a rural area in Colombia. We used both, a frequentist approach, and Bayesian latent class models to estimate the sensitivity and specificity of five tests for hookworm detection, and to estimate the prevalence of hookworm infection in absence of a Gold Standard. The Kato-Katz and agar plate methods had an overall agreement of 95% and kappa coefficient of 0.76. Different models estimated a sensitivity between 76% and 92% for the agar plate technique, and 52% to 87% for the Kato-Katz technique. The other tests had lower sensitivity. All tests had specificity between 95% and 98%. The prevalence estimated by the Kato-Katz and Agar plate methods for different subpopulations varied between 10% and 14%, and was consistent with the prevalence estimated from the combination of all tests. The Harada-Mori, Ritchie-Frick and direct examination techniques resulted in lower and disparate prevalence estimates. Bayesian approaches assuming imperfect specificity resulted in lower prevalence estimates than the frequentist approach. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of the response of PVA-GTA Fricke-gel dosimeters with clinical magnetic resonance imaging

NASA Astrophysics Data System (ADS)

Collura, Giorgio; Gallo, Salvatore; Tranchina, Luigi; Abbate, Boris Federico; Bartolotta, Antonio; d'Errico, Francesco; Marrale, Maurizio

2018-01-01

Fricke gel dosimeters produced with a matrix of Poly-vinyl alcohol (PVA) cross-linked with glutaraldehyde (GTA) were analyzed with magnetic resonance imaging (MRI). Previous studies based on spectrophotometry showed valuable dosimetric features of these gels in terms of X-ray sensitivity and diffusion of the ferric ions produced after irradiation. In this study, MRI was performed on the gels at 1.5 T with a clinical scanner in order to optimize the acquisition parameters and obtain high contrast between irradiated and non-irradiated samples. The PVA gels were found to offer good linearity in the range of 0-10 Gy and a stable signal for several hours after irradiation. The sensitivity was about 40% higher compared to gels produced with agarose as gelling agent. The effect of xylenol orange (XO) on the MRI signal was also investigated: gel dosimeters made without XO show higher sensitivity to x-rays than those made with XO. The dosimetric accuracy of the 3D gels was investigated by comparing their MRI response to percentage depth dose and transversal dose profile measurements made with an ionization chamber in a water phantom. The comparison of PVA-GTA gels with and without XO showed that the chelating agent reduces the MRI sensitivity of the gels. Depth-dose and transversal dose profiles acquired by PVA-GTA gels without XO are more accurate and consistent with the ionization chamber data. However, diffusion effects hinder accurate measurements in the steep dose gradient regions and they should be further reduced by modifying the gel matrix and/or by minimizing the delay between irradiation and imaging.

Dosimetric impact of a change in breathing period on VMAT stereotactic ablative body radiotherapy

NASA Astrophysics Data System (ADS)

Olding, T.; Alexander, KM

2017-05-01

The dosimetric impact of a change in breathing period during treatment was assessed for a volumetric modulated arc therapy (VMAT) stereotactic ablative radiotherapy (SABR) lung plan optimized according to our centre’s planning protocol. Plan delivery was evaluated at three breathing rates ranging from 7 to 23 breaths-per-minute (BPM) against the planning anatomy (15 BPM) calculated dose. Dynamic ion chamber, EBT3 film and Fricke-xylenol orange-gelatin (FXG) gel measurements were acquired using a motion phantom with appropriate inserts for each dosimeter. The results show good agreement between measured and calculated plan dose within the internal gross tumour volume (IGTV) target.

KSC-08pd0983

NASA Image and Video Library

2008-04-18

CAPE CANAVERAL, Fla. -- Florida Gov. Charlie Crist (center, by the podium) makes an appearance at the luncheon held during NASA’s Future Forum in Miami. The keynote presentation was given by astronaut Steve Frick, who was commander of the STS-122 shuttle mission. The forum focused on how space exploration benefits Florida's economy. The event, which included presentations and panels, was held at the University of Miami's BankUnited Center. Among those participating were NASA Deputy Administrator Shana Dale, astronaut Carl Walz, director of the Advanced Capabilities Division in NASA's Exploration Systems Mission Directorate, and Russell Romanella, director, International Space Station and Spacecraft Processing. Photo credit: NASA/Kim Shiflett

Henry Barton Jacobs, William Osler's intimate friend

PubMed Central

2017-01-01

William Osler was considered a universal friend by physicians of his era but, as with most people, his intimate friends were few. Henry Barton Jacobs became a close friend as one of the “latchkeyers” who lived next door to the Oslers in Baltimore, and the friendship intensified after Jacobs married Mary Sloan Frick Garrett, the fabulously wealthy widow of a former patient. The couples stayed close after the Oslers moved to Oxford, vacationing together and corresponding frequently. The couple friendship between the Oslers and the Jacobses benefited American medicine in specific ways, including the care of patients with tuberculosis and the care of children. PMID:28127152

Did Darwin really answer Paley's question?

PubMed

Brunnander, Björn

2013-09-01

It is commonly thought that natural selection explains the rise of adaptive complexity. Razeto-Barry and Frick (2011) have recently argued in favour of this view, dubbing it the Creative View. I argue that the Creative View is mistaken if it claims that natural selection serves to answer Paley's question. This is shown by a case that brings out the contrastive structure inherent in this demand for explanation. There is, however, a rather trivial sense in which specific environmental conditions are crucial for the rise of specific adaptations, but this is hardly what opponents of the Creative View are denying. Copyright © 2013 Elsevier Ltd. All rights reserved.

KSC-07pd2616

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, STS-122 crew members are introduced to part of the LESS. From left are Mission Specialists Hans Schlegel, Rex Walheim and European Space Agency astronaut Leopold Eyharts, Commander Stephen Frick, Mission Specialist Leland Melvin and Pilot Alan Poindexter. The crew is at Kennedy to take part in a crew equipment interface test, or CEIT, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

STS-110 crew in M-113 personnel carrier during TCDT

NASA Technical Reports Server (NTRS)

2002-01-01

KENNEDY SPACE CENTER, FLA. -- With fellow crew members Mission Specialists Rex Walheim and Ellen Ochoa (waving her arm) and a trainer aboard, STS-110 Pilot Stephen Frick stirs up dust behind the M-113 armored personnel carrier as he practices driving it. The training is part of Terminal Countdown Demonstration Test activities, which include emergency egress training and a simulated launch countdown. The TCDT is held at KSC prior to each Space Shuttle flight. Scheduled for launch April 4, the 11-day mission will feature Shuttle Atlantis docking with the International Space Station (ISS) and delivering the S0 truss, the centerpiece-segment of the primary truss structure that will eventually extend over 300 feet.

Gamma irradiator dose mapping simulation using the MCNP code and benchmarking with dosimetry.

PubMed

Sohrabpour, M; Hassanzadeh, M; Shahriari, M; Sharifzadeh, M

2002-10-01

The Monte Carlo transport code, MCNP, has been applied in simulating dose rate distribution in the IR-136 gamma irradiator system. Isodose curves, cumulative dose values, and system design data such as throughputs, over-dose-ratios, and efficiencies have been simulated as functions of product density. Simulated isodose curves, and cumulative dose values were compared with dosimetry values obtained using polymethyle-methacrylate, Fricke, ethanol-chlorobenzene, and potassium dichromate dosimeters. The produced system design data were also found to agree quite favorably with those of the system manufacturer's data. MCNP has thus been found to be an effective transport code for handling of various dose mapping excercises for gamma irradiators.

KSC-04pd0402

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - In the electrical engineering lab of the SRB Assembly and Refurbishment Facility, STS-114 crew members look at a DAS (data acquisition system) unit and some of the different circuit boards that will help drive the cameras on future flights and different cameras. In the foreground are Mission Specialists Soichi Noguchi, Stephen Robinson and Andrew Thomas. In the background (center, left to right) are Pilot James Kelly; Mission Specialists Charles Camarda and Wendy Lawrence; plus astronaut Steven Frick, who joined the STS-114 crew during equipment familiarization at KSC. The STS-114 mission is Logistics Flight 1, which is scheduled to deliver supplies and equipment, plus the external stowage platform, to the International Space Station.

KSC-07pd2610

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, members of the STS-122 crew get information about the thermal protection system on space shuttle Atlantis (overhead). From left are Pilot Alan Poindexter, Mission Specialists Rex Walheim, Commander Stephen Frick, and Mission Specialists Hans Schlegel, Leland Melvin and Stanley Love. Schlegel represents the European Space Agency. The crew is at Kennedy to take part in a crew equipment interface test, or CEIT, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd2608

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, members of the STS-122 crew get a close look at the landing gear on space shuttle Atlantis. From left are Mission Specialist Hans Schlegel, Pilot Alan Poindexter, Mission Specialists Rex Walheim and Leland Melvin and Commander Stephen Frick. Schlegel represents the European Space Agency. The crew is at Kennedy to take part in a crew equipment interface test, or CEIT, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

Long-term changes in solar wind elemental and isotopic ratios - A comparison of two lunar ilmenites of different antiquities

NASA Technical Reports Server (NTRS)

Becker, Richard H.; Pepin, Robert O.

1989-01-01

The solar wind components in two lunar ilmenites are examined. The noble gas and nitrogen elemental and isotopic abundances of lunar regolith breccia sample 79035, assumed to have been exposed to solar winds more than 2 Ga ago, are analyzed using stepwise oxidation and pyrolysis. This sample is compared with the data of Frick et al. (1988) for soil sample 71501, recently exposed to solar winds. It is observed that the two elements differ in terms of xenon abundance, helium and neon isotopic rates, and He/Ar elemental ratios. It is concluded that there have been isotopic and elemental abundance changes in solar wind composition over time.

Minimizing variability of cascade impaction measurements in inhalers and nebulizers.

PubMed

Bonam, Matthew; Christopher, David; Cipolla, David; Donovan, Brent; Goodwin, David; Holmes, Susan; Lyapustina, Svetlana; Mitchell, Jolyon; Nichols, Steve; Pettersson, Gunilla; Quale, Chris; Rao, Nagaraja; Singh, Dilraj; Tougas, Terrence; Van Oort, Mike; Walther, Bernd; Wyka, Bruce

2008-01-01

The purpose of this article is to catalogue in a systematic way the available information about factors that may influence the outcome and variability of cascade impactor (CI) measurements of pharmaceutical aerosols for inhalation, such as those obtained from metered dose inhalers (MDIs), dry powder inhalers (DPIs) or products for nebulization; and to suggest ways to minimize the influence of such factors. To accomplish this task, the authors constructed a cause-and-effect Ishikawa diagram for a CI measurement and considered the influence of each root cause based on industry experience and thorough literature review. The results illustrate the intricate network of underlying causes of CI variability, with the potential for several multi-way statistical interactions. It was also found that significantly more quantitative information exists about impactor-related causes than about operator-derived influences, the contribution of drug assay methodology and product-related causes, suggesting a need for further research in those areas. The understanding and awareness of all these factors should aid in the development of optimized CI methods and appropriate quality control measures for aerodynamic particle size distribution (APSD) of pharmaceutical aerosols, in line with the current regulatory initiatives involving quality-by-design (QbD).

Observation of dose-rate dependence in a Fricke dosimeter irradiated at low dose rates with monoenergetic X-rays.

PubMed

O'Leary, Mel; Boscolo, Daria; Breslin, Nicole; Brown, Jeremy M C; Dolbnya, Igor P; Emerson, Chris; Figueira, Catarina; Fox, Oliver J L; Grimes, David Robert; Ivosev, Vladimir; Kleppe, Annette K; McCulloch, Aaron; Pape, Ian; Polin, Chris; Wardlow, Nathan; Currell, Fred J

2018-03-16

Absolute measurements of the radiolytic yield of Fe3+ in a ferrous sulphate dosimeter formulation (6 mM Fe2+), with a 20 keV x-ray monoenergetic beam, are reported. Dose-rate suppression of the radiolytic yield was observed at dose rates lower than and different in nature to those previously reported with x-rays. We present evidence that this effect is most likely to be due to recombination of free radicals radiolytically produced from water. The method used to make these measurements is also new and it provides radiolytic yields which are directly traceable to the SI standards system. The data presented provides new and exacting tests of radiation chemistry codes.

General and maladaptive personality dimensions and the assessment of callous-unemotional traits in adolescence.

PubMed

Decuyper, Mieke; De Bolle, Marleen; De Fruyt, Filip; De Clercq, Barbara

2011-10-01

Associations between callous-unemotional traits and general and maladaptive personality dimensions are examined in adolescence. More specifically, it was investigated to what extent general and maladaptive personality dimensions can account for the variance in callous-unemotional (CU) scores. Adolescents (N = 509) and their mothers completed the Inventory of Callous-Unemotional Traits (ICU; Frick, 2003), the Hierarchical Personality Inventory for Children (HiPIC; Mervielde & De Fruyt, 1999, 2002), and the Dimensional Personality Symptom Item Pool (DIPSI; De Clercq, De Fruyt, Van Leeuwen, & Mervielde, 2006). Both personality measures accounted for substantial variance in ICU scores and the overall CU profile in terms of the HiPIC and DIPSI was consistent with psychopathy conceptualizations and consistent across informant. Implications for the assessment of early externalizing trait pathology are discussed.

A suggested periodic table up to Z≤ 172, based on Dirac-Fock calculations on atoms and ions.

PubMed

Pyykkö, Pekka

2011-01-07

Extended Average Level (EAL) Dirac-Fock calculations on atoms and ions agree with earlier work in that a rough shell-filling order for the elements 119-172 is 8s < 5g≤ 8p(1/2) < 6f < 7d < 9s < 9p(1/2) < 8p(3/2). The present Periodic Table develops further that of Fricke, Greiner and Waber [Theor. Chim. Acta 1971, 21, 235] by formally assigning the elements 121-164 to (nlj) slots on the basis of the electron configurations of their ions. Simple estimates are made for likely maximum oxidation states, i, of these elements M in their MX(i) compounds, such as i = 6 for UF(6). Particularly high i are predicted for the 6f elements.

Nonpathological and pathological narcissism: which self-reported characteristics are most problematic in adolescents?

PubMed

Barry, Christopher T; Kauten, Rebecca L

2014-01-01

Prior research indicates that dimensions of adolescent narcissism differ in their associations with indicators of positive and negative psychological functioning (e.g., Barry, Frick, Adler, & Grafeman, 2007 ; Barry & Wallace, 2010 ). This study investigated correlates of 2 empirically derived factors of adolescent narcissism (i.e., pathological and nonpathological narcissism) from 2 measures thought to differ based on their inclusion of pathological versus nonpathological content. In a sample of 188 at-risk adolescents ages 16 to 18, pathological narcissism was associated with various indicators of maladjustment, including aggression, low self-esteem, internalizing problems, and poor perceived interpersonal relationships. On the other hand, nonpathological narcissism was positively associated with self-esteem and aggression but negatively associated with internalizing problems. The implications for the conceptualization of adolescent narcissism are discussed.

KSC-07pd2611

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- From a lower level in the Orbiter Processing Facility, members of the STS-122 crew check out the landing gear on space shuttle Atlantis, overhead. Dressed in their blue suits are Mission Specialist Leland Melvin, Commander Stephen Frick, European Space Agency astronaut Leopold Eyharts and Pilot Alan Poindexter. Eyharts will be traveling to the International Space Station to join the Expedition 16 crew as a flight engineer. The crew is at Kennedy to take part in a crew equipment interface test, or CEIT, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd3373

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- Space shuttle Atlantis STS-122 Commander Steve Frick responds to a question from the media during a press conference at the slidewire basket landing on Launch Pad 39A. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd2652

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, STS-122 crew members practice working with equipment for the mission. From left are Commander Stephen Frick and Mission Specialists Hans Schlegel, Rex Walheim and Stanley Love. Schlegel represents the European Space Agency. The crew is at Kennedy Space Center to take part in a crew equipment interface test, which includes equipment familiarization. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-08pd0976

NASA Image and Video Library

2008-04-18

CAPE CANAVERAL, Fla. -- One of the panels conducted during NASA’s Future Forum in Miami featured (left to right) Penny Haskins (at the podium), associate director of the Florida Space Grant Consortium; Okhee Lee-Salwen, with the University of Miami’s College of Education; Bernice Alston, NASA deputy assistant administrator for education; Frank Brogan, president of Florida Atlantic University and former Florida lieutenant governor; Steve Frick, astronaut and commander of the STS-122 space shuttle mission. The forum, which focused on how space exploration benefits Florida's economy, was held at the University of Miami's BankUnited Center and included presentations and panels. Among those participating were NASA Deputy Administrator Shana Dale, astronaut Carl Walz, director of the Advanced Capabilities Division in NASA's Exploration Systems Mission Directorate, and Russell Romanella, director, International Space Station and Spacecraft Processing. Photo credit: NASA/Kim Shiflett

Water-equivalence of gel dosimeters for radiology medical imaging.

PubMed

Valente, M; Vedelago, J; Chacón, D; Mattea, F; Velásquez, J; Pérez, P

2018-03-08

International dosimetry protocols are based on determinations of absorbed dose to water. Ideally, the phantom material should be water equivalent; that is, it should have the same absorption and scatter properties as water. This study presents theoretical, experimental and Monte Carlo modeling of water-equivalence of Fricke and polymer (NIPAM, PAGAT and itaconic acid ITABIS) gel dosimeters. Mass and electronic densities along with effective atomic number were calculated by means of theoretical approaches. Samples were scanned by standard computed tomography. Photon mass attenuation coefficients and electron stopping powers were examined. Theoretical, Monte Carlo and experimental results confirmed good water-equivalence for all gel dosimeters. Overall variations with respect to water in the low energy radiology range (up to 130 kVp) were found to be less than 3% in average. Copyright © 2018 Elsevier Ltd. All rights reserved.

Criminal characteristics of a group of primary criminals diagnosed with aspd: approach to criminal recidivis.

PubMed

Larrotta-Castillo, R; Garivia, A M; Mora-Jaimes, C; Gómez-Abril, D A

2017-12-01

Antisocial personality disorder (ASPD) is commonly associated with the risk of criminal recidivism. Knowing more about the factors associated with this pattern of behaviour can help with the design of effective prevention strategies. The purpose of this article is to establish if there are differences in socio-criminogenic variables of a group of criminals sentenced for the first time and with APSD compared to another group of first-time offenders who do not present this disorder. Analytical observation study of 70 men classified into 2 groups according to the presence of ASPD TPA (n=47; age: 29.98±7.8 years) or absence of ASPD (n=23; age: 32.35±8.7 years). The inmates with ASPD showed higher frequencies of current consumption of psychoactive substances (31.9%), criminal associations and simultaneous use of psychoactive substances (70.2%), having committed the crime under the effects of a psychoactive substance (55.3%), not having the possibility of distancing themselves from criminal associations (83%) and a lack of legal resources for proceedings for defence and release (76.6%). This sample contains a group of variables called dynamic that are more commonly present amongst first time offenders with ASPD; said variables have been associated as major predictors of recidivism. Given that they are regarded as dynamic, they may well be modifiable.

KSC-07pd2660

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- STS-122 crew members get a close look at shuttle equipment from inside the payload bay of space shuttle Atlantis. The crew comprises six astronauts: Commander Stephen Frick, Pilot Alan Poindexter and Mission Specialists Rex Walheim, Stanley Love, Leland Melvin and Hans Schlegel, who represents the European Space Agency. A seventh astronaut is Leopold Eyharts, also with the ESA, who will join the Expedition 16 crew as flight engineer on the International Space Station. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd2658

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- STS-122 crew members get a close look at shuttle equipment from inside the payload bay of space shuttle Atlantis. The crew comprises six astronauts: Commander Stephen Frick, Pilot Alan Poindexter and Mission Specialists Rex Walheim, Stanley Love, Leland Melvin and Hans Schlegel, who represents the European Space Agency. A seventh astronaut is Leopold Eyharts, also with the ESA, who will join the Expedition 16 crew as flight engineer on the International Space Station. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd2651

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, STS-122 crew members practice working with equipment for the mission. From left are Commander Stephen Frick and Mission Specialists Hans Schlegel, Leland Melvin (behind), Rex Walheim and Stanley Love. Schlegel represents the European Space Agency. The crew is at Kennedy Space Center to take part in a crew equipment interface test, which includes equipment familiarization. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd2659

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- STS-122 crew members get a close look at shuttle equipment from inside the payload bay of space shuttle Atlantis. The crew comprises six astronauts: Commander Stephen Frick, Pilot Alan Poindexter and Mission Specialists Rex Walheim, Stanley Love, Leland Melvin and Hans Schlegel, who represents the European Space Agency. A seventh astronaut is Leopold Eyharts, also with the ESA, who will join the Expedition 16 crew as flight engineer on the International Space Station. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd3604

NASA Image and Video Library

2007-12-09

KENNEDY SPACE CENTER, FLA. -- On the Shuttle Landing Facility at NASA's Kennedy Space Center, STS-122 Commander Steve Frick heads for the plane for the return trip to Houston. The crew is flying back to Houston after launch of space shuttle Atlantis was delayed when a failure occurred in a fuel sensor system while the vehicle's external fuel tank was being filled. One of the four engine cutoff, or ECO, sensors inside the liquid hydrogen section of the tank gave a false reading and NASA's current Launch Commit Criteria require that all four sensors function properly. The sensor system is one of several that protect the shuttle's main engines by triggering their shut down if fuel runs unexpectedly low. Space shuttle Atlantis' STS-122 mission now is targeted to launch no earlier than Jan. 2. The liftoff date depends on the resolution of the problem in the fuel sensor system. Photo credit: NASA/Kim Shiflett

Crewmembers share a meal in the SM

NASA Image and Video Library

2008-02-10

S122-E-007069 (9 Feb. 2008) --- An auto-set digital camera records a rare but not unique moment on the International Space Station as a total of ten travelers share a few light moments before joining forces for several days of work aboard the orbital outpost. On the left side of the frame, from top to bottom, are astronauts Daniel Tani, Stanley Love and the European Space Agency's Leopold Eyharts. In the center, from the top, are astronauts Leland Melvin, Rex Walheim, Steve Frick, Peggy Whitson and Alan Poindexter. Cosmonaut Yuri Malenchenko of Russia's Federal Space Agency is top right and below him is ESA astronaut Hans Schlegel. Tani, who has been serving as a flight engineer on the ISS for several months, now gets to trade places with Eyharts. Whitson and Malenchenko both will continue their tours of duty on the station once the STS-122 crew returns to Earth.

Molecular Survey for the Invasive Leafminer Pest Liriomyza huidobrensis (Diptera: Agromyzidae) in California Uncovers Only the Native Pest Liriomyza langei.

PubMed

Scheffer, Sonja J; Lewis, Matthew L; Gaimari, Stephen D; Reitz, Stuart R

2014-10-01

Liriomyza huidobrensis (Blanchard) is a highly destructive invasive leafminer pest currently causing extensive damage to vegetable and horticultural crops around the world. Liriomyza langei Frick is a leafminer pest native to California that cannot currently be morphologically distinguished from L. huidobrensis. We used a DNA-barcoding approach, a published PCR-RFLP method, and a new multiplex PCR method to analyze 664 flies matching the morphological description of huidobrensis-langei. We found no evidence for the presence of L. huidobrensis in our extensive samples from California. In addition to the new molecular method, this work is important because it provides definitive data that the California "pea leafminer" is currently, and has probably always been, L. langei. These data will also be important in the event that the highly invasive L. huidobrensis ever becomes established. © 2014 Entomological Society of America.

Geomyces and Pseudogymnoascus: Emergence of a primary pathogen, the causative agent of bat white-nose syndrome: Chapter 28

USGS Publications Warehouse

Verant, Michelle L.; Minnis, Andrew M.; Lindner, Daniel L.; Blehert, David

2017-01-01

Geomyces and Pseudogymnoascus (Fungi, Ascomycota, Leotiomycetes, aff. Thelebolales) are closely related groups of globally occurring soil-associated fungi. Recently, these genera of fungi have received attention because a newly identified species, Pseudogymnoascus (initially classified as Geomyces) destructans, was discovered in association with significant and unusual mortality of hibernating bats in North America (Blehert et al. 2009; Gargas et al. 2009; Minnis and Linder 2013). This emergent disease called bat white-nose syndrome (WNS), has since caused drastic declines in populations of hibernating bats in the United States and Canada (Turner, Reeder, and Coleman 2011; Thogmartin et al. 2012) and threatens some species with regional extinction (Frick et al. 2010; Langwig et al. 2012; Thogmartin et al. 2013). As primary predators of insects and keystone species for cave ecosystems, the loss of bats due to WNS has important economic and ecological implications.

Characterisation of TruView™: a new 3-D reusable radiochromic MethylThymolBlue based gel dosimeter for ionising radiations

NASA Astrophysics Data System (ADS)

Colnot, J.; Huet, C.; Clairand, I.

2017-05-01

TruView™ is a new water-equivalent reusable Fricke gel dosimeter based on MethylThymolBlue reactive dye. Details of the characterisation of the TruView™ MTB gel dosimeter by spectrophotometric measurements and of its reading with the Optical-CT Scanner Vista™ are described. In this study, the different parameters influencing TruView™ dose response have been studied and its performances have been compared to chamber and diodes measurements. This gel presents a linear response with dose up to 20 Gy, independent in the investigated range of photon beam energy and dose rate and also a good intra-batch uniformity. Ions diffusion into the matrix homogenizes the gel after a week, losing dosimetric information but allowing a new irradiation to be performed. However, auto-oxidation happens before and after irradiation, degrading the dosimeter response and stability. Storage and reading conditions affect the response as well.

KSC-08pd0398

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- At the Shuttle Landing Facility at NASA's Kennedy Space Center, STS-122 Commander Steve Frick (right) and Pilot Alan Poindexter exit the crew transport vehicle. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

KSC-07pd3336

NASA Image and Video Library

2007-11-18

KENNEDY SPACE CENTER, FLA. -- STS-122 Commander Stephen Frick takes time out from driving practice of the M-113 armored personnel carrier to pose for a photo. The practice near Launch Pad 39B is part of training on emergency egress procedures. An M-113 will be available to transport the crew to safety in the event of a contingency on the pad before their launch. The crew is participating in Terminal Countdown Demonstration Test activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd2645

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, STS-122 Commander Stephen Frick checks out the cockpit on space shuttle Atlantis. He and other crew members are at Kennedy Space Center to take part in a crew equipment interface test, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd2644

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, STS-122 Commander Stephen Frick checks out the cockpit on space shuttle Atlantis. He and other crew members are at Kennedy Space Center to take part in a crew equipment interface test, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

Relative precision of inhaler aerodynamic particle size distribution (APSD) metrics by full resolution and abbreviated andersen cascade impactors (ACIs): part 2--investigation of bias in extra-fine mass fraction with AIM-HRT impactor.

PubMed

Mitchell, Jolyon P; Nagel, Mark W; Doyle, Cathy C; Ali, Rubina S; Avvakoumova, Valentina I; Christopher, J David; Quiroz, Jorge; Strickland, Helen; Tougas, Terrence; Lyapustina, Svetlana

2010-09-01

The purpose of this study was to resolve an anomalously high measure of extra-fine particle fraction (EPF) determined by the abbreviated cascade impactor possibly relevant for human respiratory tract (AIM-HRT) in the experiment described in Part 1 of this two-part series, in which the relative precision of abbreviated impactors was evaluated in comparison with a full resolution Andersen eight-stage cascade impactor (ACI). Evidence that the surface coating used to mitigate particle bounce was laterally displaced by the flow emerging from the jets of the lower stage was apparent upon microscopic examination of the associated collection plate of the AIM-HRT impactor whose cut point size defines EPF. A filter soaked in surfactant was floated on top of this collection plate, and further measurements were made using the same pressurized metered-dose inhaler-based formulation and following the same procedure as in Part 1. Measures of EPF, fine particle, and coarse particle fractions were comparable with those obtained with the ACI, indicating that the cause of the bias had been identified and removed. When working with abbreviated impactors, this precaution is advised whenever there is evidence that surface coating displacement has occurred, a task that can be readily accomplished by microscopic inspection of all collection plates after allowing the impactor to sample ambient air for a few minutes.

Energy dependence of lithium fluoride dosemeter for high energy electrons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antoku, S.; Sunayashiki, T.; Takeoka, S.

1973-11-01

A lithium fluoride and a Fricke dosemeter have been exposed simultaneously to /sup 60/Co gamma -rays and 10, 20, and 30 MeV electrons to study the energy dependence of the lithium fluoride dosemeter for high-energy electrons, with particular reference to possible significant reductions in the sensitivity of LiF phosphors for electrons as compared with /sup 60/Co gamma - rays. In the present study, the direct comparison excluded errors resulting from uncertainties about ion recombination and conversion factors from roentgens to rads for ionization chambers. The dosemeters were exposed to approximately 5000 rads of each radiation at the appropriate peak depthmore » in a water phantom. Corrections for the supra-linear response for LiF were made using a dose response curve for /sup 60/Co gamma -rays. The three types of LiF phosphor examined did not exhibit any energy dependence for electrons compared with /sup 60/Co gamma - rays. Within the statistical uncertainty (~3%) for the experiment. (UK)« less

KSC-02pd0387

NASA Image and Video Library

2002-04-03

KENNEDY SPACE CENTER, FLA. -- While gathering with friends and family at the pad, the STS-110 crew poses in front of Space Shuttle Atlantis still enclosed by the Rotating Service Structure. Standing left to right are Mission Specialist Steven Smith, Jerry Ross and Lee Morin; Pilot Stephen Frick; Mission Specialist Rex Walheim; Commander Michael Bloomfield; and Mission Specialist Ellen Ochoa. The mission continues the expansion of the International Space Station by delivering and installing the S0 Integrated Truss Structure, the initial section of a framework that will eventually hold the power and cooling systems needed for future international research laboratories. The payload also comprises the Canadian Mobile Transporter (attached to the S0 truss), power distribution system modules, a heat pipe radiator for cooling, computers and a pair of rate gyroscopes. The 11-day mission is the 13th assembly flight to the ISS and includes four spacewalks to attach the S0 truss to the U.S. Lab Destiny. Launch is scheduled for April 4

KSC-02pd0388

NASA Image and Video Library

2002-04-03

KENNEDY SPACE CENTER, FLA. -- While gathering with friends and family at the pad, the STS-110 crew poses in front of Space Shuttle Atlantis still enclosed by the Rotating Service Structure. Standing left to right are Mission Specialist Steven Smith, Jerry Ross and Lee Morin; Pilot Stephen Frick; Mission Specialist Rex Walheim; Commander Michael Bloomfield; and Mission Specialist Ellen Ochoa. The mission continues the expansion of the International Space Station by delivering and installing the S0 Integrated Truss Structure, the initial section of a framework that will eventually hold the power and cooling systems needed for future international research laboratories. The payload also comprises the Canadian Mobile Transporter (attached to the S0 truss), power distribution system modules, a heat pipe radiator for cooling, computers and a pair of rate gyroscopes. The 11-day mission is the 13th assembly flight to the ISS and includes four spacewalks to attach the S0 truss to the U.S. Lab Destiny. Launch is scheduled for April 4

KSC-08pd0406

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- After exiting the crew transport vehicle on the Shuttle Landing Facility at NASA's Kennedy Space Center, STS-122 Commander Steve Frick and Pilot Alan Poindexter begin their examination of the thermal protection system on space shuttle Atlantis. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

KSC-08pd0404

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- After exiting the crew transport vehicle, STS-122 Commander Steve Frick tells the media how thankful he and the crew are for the shuttle and mission preparation that made the mission such a success. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

KSC-08pd0403

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- After exiting the crew transport vehicle, STS-122 Pilot Alan Poindexter (left) and Commander Steve Frick talk to Director of Mission Launch Integration LeRoy Cain and NASA Associate Administrator for Space Operations William Gerstenmaier. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

KSC-07pd2646

NASA Image and Video Library

2007-09-28

KENNEDY SPACE CENTER, FLA. -- In the Orbiter Processing Facility, United Space Alliance technicians provide lights over the space shuttle Atlantis' cockpit. STS-122 Commander Stephen Frick is inside checking the cockpit for launch readiness. The crew is at Kennedy Space Center to take part in a crew equipment interface test, which helps familiarize them with equipment and payloads for the mission. Among the activities standard to a CEIT are harness training, inspection of the thermal protection system and camera operation for planned extravehicular activities, or EVAs. The mission will carry and install the Columbus Lab, a multifunctional, pressurized laboratory that will be permanently attached to Node 2 of the space station to carry out experiments in materials science, fluid physics and biosciences, as well as to perform a number of technological applications. It is Europe’s largest contribution to the construction of the International Space Station and will support scientific and technological research in a microgravity environment. STS-122 is targeted for launch in December. Photo credit: NASA/Kim Shiflett

KSC-07pd3334

NASA Image and Video Library

2007-11-18

KENNEDY SPACE CENTER, FLA. -- The STS-122 crew poses for a group portrait near Launch Pad 39B during a training session on the operation of the M-113 armored personnel carrier. An M-113 will be available to transport the crew to safety in the event of an emergency on the pad before their launch. From left are Mission Specialists Rex Walheim, Leopold Eyharts and Hans Schlegel of the European Space Agency, Stanley Love; Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialist Leland Melvin. The crew is participating in Terminal Countdown Demonstration Test activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Fifth Fundamental Catalogue (FK5). Part 1: Basic fundamental stars (Fricke, Schwan, and Lederle 1988): Documentation for the machine-readable version

NASA Technical Reports Server (NTRS)

Warren, Wayne H., Jr.

1990-01-01

The machine-readable version of the catalog, as it is currently being distributed from the Astronomical Data Center, is described. The Basic FK5 provides improved mean positions and proper motions for the 1535 classical fundamental stars that had been included in the FK3 and FK4 catalogs. The machine version of the catalog contains the positions and proper motions of the Basic FK5 stars for the epochs and equinoxes J2000.0 and B1950.0, the mean epochs of individual observed right ascensions and declinations used to determine the final positions, and the mean errors of the final positions and proper motions for the reported epochs. The cross identifications to other designations used for the FK5 stars that are given in the published catalog were not included in the original machine versions, but the Durchmusterung numbers have been added at the Astronomical Data Center.

Spousal Similarity in Life Satisfaction before and after Divorce

PubMed Central

Wortman, Jessica; Lucas, Richard E.

2015-01-01

Previous research has explored possible origins of individual differences in subjective well-being, focusing largely on stable, internal characteristics of traits as predictors of life satisfaction (Diener & Lucas, 1999). Although past work has demonstrated that life satisfaction is largely stable over the life span, other evidence has also demonstrated the lasting impact of life events. In this study, we use married couples as a test of the impact of life circumstances on life satisfaction, focusing on similarity in life satisfaction before and after divorce. If life satisfaction is impacted by shared life circumstances, married couples (who share life circumstances) should show greater similarity in life satisfaction before divorce than after. We tested this possibility using a dyadic latent-state-trait model that examined cross-spouse similarity in the stable and changing components of life satisfaction. Using a nationally representative panel study from Germany (Wagner, Frick & Schupp, 2007), we showed that similarity declined substantially following divorce. This suggests that life satisfaction is related to shared life circumstances. PMID:26436842

Spousal similarity in life satisfaction before and after divorce.

PubMed

Wortman, Jessica; Lucas, Richard E

2016-04-01

Previous research has explored possible origins of individual differences in subjective well-being, focusing largely on stable, internal characteristics of traits as predictors of life satisfaction (Diener & Lucas, 1999). Although past work has demonstrated that life satisfaction is largely stable over the life span, other evidence has also demonstrated the lasting impact of life events. In this study, we use married couples as a test of the impact of life circumstances on life satisfaction, focusing on similarity in life satisfaction before and after divorce. If life satisfaction is impacted by shared life circumstances, married couples (who share life circumstances) should show greater similarity in life satisfaction before divorce than after. We tested this possibility using a dyadic latent-state-trait model that examined cross-spouse similarity in the stable and changing components of life satisfaction. Using a nationally representative panel study from Germany (Wagner, Frick & Schupp, 2007), we showed that similarity declined substantially following divorce. This suggests that life satisfaction is related to shared life circumstances. (c) 2016 APA, all rights reserved).

Effects of gamma-Radiation on Select Lipids and Antioxidants

NASA Technical Reports Server (NTRS)

Gandolph, Jacob; Mauer, Lisa; Perchonok, Michele

2006-01-01

Radiation encountered on an extended duration space mission (estimates of 3 Sieverts for a mission to Mars) poses a threat not only to human health, but also to the quality, nutritional value, and palatability of the food system. Free radicals generated by radiation interaction with foods may initiate many unwanted reactions including: 1) autoxidation in lipids that alters flavor, odor, and concentrations of essential fatty acids, and 2) depletion of antioxidants food products and dietary supplements. Studies have shown that antioxidants may provide long term health protection from oxidative stress caused by radiation exposure; therefore, consumption of antioxidants will be important. Stability of essential fatty acids is also important for astronauts long-term health status. The objectives of this study were to characterize the effects of low dose gamma-radiation on lipids and antioxidants by monitoring oxidation and reducing power, respectively, in model systems. Select oils and antioxidants were exposed to levels of gamma-radiation ranging from 0 to 1000 Gy (1 Gy = 1 Sv) using a Gammacell 220 and stored at ambient or elevated temperatures (65 C) for up to 3 months prior to analysis. A Fricke dosimeter was used to verify differences between the radiation doses administered. Primary and secondary products of lipid oxidation in soybean and peanut oils were monitored using conjugated diene and 2-thiobarbituric acid (TBARs) assays. Changes in fatty acid composition and formation and vitamin E levels were also measured. The reducing power of antioxidant compounds, including vitamins C and E and beta-carotene, was determined using the ferric reducing antioxidant power (FRAP) assay. Significant differences (alpha =0.05) were present between all radiation doses tested using the Fricke dosimeter. Increasing radiation doses above 3 Sv resulted in significantly (alpha =0.05) elevated levels of oxidation and free fatty acids in soybean and peanut oils. Decreases in concentrations of essential fatty acids upon increasing radiation doses were also observed. Increasing radiation doses caused significant (alpha =0.05) decreases in reducing power and hence the effectiveness of vitamins C and E as well as beta-carotene. This work establishes a need for quantifying the effects of space relevant radiation doses in the development of a food system for an extended duration mission and for identifying threshold radiation levels that will impact the useful shelf-life of the variety of foods that will be sent. Eventual rancidity of lipids and the loss of antioxidant bioprotective effects are major concerns for the acceptability and nutritional profile of a food system.

Discriminating Ability of Abbreviated Impactor Measurement Approach (AIM) to Detect Changes in Mass Median Aerodynamic Diameter (MMAD) of an Albuterol/Salbutamol pMDI Aerosol.

PubMed

David Christopher, J; Patel, Rajni B; Mitchell, Jolyon P; Tougas, Terrence P; Goodey, Adrian P; Quiroz, Jorge; Andersson, Patrik U; Lyapustina, Svetlana

2017-11-01

This article reports on results from a two-lab, multiple impactor experiment evaluating the abbreviated impactor measurement (AIM) concept, conducted by the Cascade Impaction Working Group of the International Pharmaceutical Aerosol Consortium on Regulation and Science (IPAC-RS). The goal of this experiment was to expand understanding of the performance of an AIM-type apparatus based on the Andersen eight-stage non-viable cascade impactor (ACI) for the assessment of inhalation aerosols and sprays, compared with the full-resolution version of that impactor described in the pharmacopeial compendia. The experiment was conducted at two centers with a representative commercially available pressurized metered dose inhaler (pMDI) containing albuterol (salbutamol) as active pharmaceutical ingredient (API). Metrics of interest were total mass (TM) emitted from the inhaler, impactor-sized mass (ISM), as well as the ratio of large particle mass (LPM) to small particle mass (SPM). ISM and the LPM/SPM ratio together comprise the efficient data analysis (EDA) metrics. The results of the comparison demonstrated that in this study, the AIM approach had adequate discrimination to detect changes in the mass median aerodynamic diameter (MMAD) of the ACI-sampled aerodynamic particle size distribution (APSD), and therefore could be employed for routine product quality control (QC). As with any test method considered for inclusion in a regulatory filing, the transition from an ACI (used in development) to an appropriate AIM/EDA methodology (used in QC) should be evaluated and supported by data on a product-by-product basis.

A Microwave Ring-Resonator Sensor for Non-Invasive Assessment of Meat Aging

PubMed Central

Jilani, Muhammad Taha; Wen, Wong Peng; Cheong, Lee Yen; ur Rehman, Muhammad Zaka

2016-01-01

The assessment of moisture loss from meat during the aging period is a critical issue for the meat industry. In this article, a non-invasive microwave ring-resonator sensor is presented to evaluate the moisture content, or more precisely water holding capacity (WHC) of broiler meat over a four-week period. The developed sensor has shown significant changes in its resonance frequency and return loss due to reduction in WHC in the studied duration. The obtained results are also confirmed by physical measurements. Further, these results are evaluated using the Fricke model, which provides a good fit for electric circuit components in biological tissue. Significant changes were observed in membrane integrity, where the corresponding capacitance decreases 30% in the early aging (0D-7D) period. Similarly, the losses associated with intracellular and extracellular fluids exhibit changed up to 42% and 53%, respectively. Ultimately, empirical polynomial models are developed to predict the electrical component values for a better understanding of aging effects. The measured and calculated values are found to be in good agreement. PMID:26805828

A Microwave Ring-Resonator Sensor for Non-Invasive Assessment of Meat Aging.

PubMed

Jilnai, Muhammad Taha; Wen, Wong Peng; Cheong, Lee Yen; ur Rehman, Muhammad Zaka

2016-01-20

The assessment of moisture loss from meat during the aging period is a critical issue for the meat industry. In this article, a non-invasive microwave ring-resonator sensor is presented to evaluate the moisture content, or more precisely water holding capacity (WHC) of broiler meat over a four-week period. The developed sensor has shown significant changes in its resonance frequency and return loss due to reduction in WHC in the studied duration. The obtained results are also confirmed by physical measurements. Further, these results are evaluated using the Fricke model, which provides a good fit for electric circuit components in biological tissue. Significant changes were observed in membrane integrity, where the corresponding capacitance decreases 30% in the early aging (0D-7D) period. Similarly, the losses associated with intracellular and extracellular fluids exhibit changed up to 42% and 53%, respectively. Ultimately, empirical polynomial models are developed to predict the electrical component values for a better understanding of aging effects. The measured and calculated values are found to be in good agreement.

KSC-08pd0407

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- After greeting the media on the Shuttle Landing Facility at NASA's Kennedy Space Center, the STS-122 crew stands in front of space shuttle Atlantis for a final group photo. From left are Mission Specialists Leland Melvin, Hans Schlegel, Rex Walheim and Stanley Love, Pilot Alan Poindexter and Commander Steve Frick. Schlegel represents the European Space Agency. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

KSC-08pd0408

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- After greeting the media on the Shuttle Landing Facility at NASA's Kennedy Space Center, the STS-122 crew signals a successful mission and landing. From left are Mission Specialists Leland Melvin, Hans Schlegel, Rex Walheim and Stanley Love, Pilot Alan Poindexter and Commander Steve Frick. Schlegel represents the European Space Agency. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

[Soil-transmitted helminth trends and prevalence in La Virgen, Colombia 1995-2005].

PubMed

Fernández-Niño, Julián A; Reyes-Harker, Patricia; Moncada-Alvarez, Ligia I; López, Myriam C; Cháves, María Del Pilar; Knudson, Angélica; Ariza, Yoseth

2007-01-01

Describing soil-transmitted helminthiasis prevalence and trends in children aged less than 15 in the village of La Virgen, Cundinamarca. Three non-random surveys were carried out on school-children aged 0 to 15 years. Intestinal parasitism was determined In the three cross-sectional studies by direct examination of fecal samples and modified Ritchie-Frick concentration method. Intestinal parasitism distribution was analysed and the trend during 1995-2005 described. The prevalence of intestinal parasitism in children aged less than 5 increased from 62,5 % in 1995 to 66,7 % in 2001 and to 69 % in 2005; soil-transmitted helminthiasis prevalence in this age group was 37,5 % in 1995, 23,6 % in 2001 and 27,6 % in 2005. The prevalence of intestinal parasitism for children aged over 5 increased from 86,2 % in 1995 to 89,1 % in 2005; soil-transmitted helminthiasis prevalence was 62,9 % in 1995, 39,8 % in 2001 and 23,9 % in 2005. Soil-transmitted helminthiasis was endemic and presented high prevalence during the study period. Effective control measures are needed to prevent intestinal parasitism in pre-school and schoolchildren.

KSC-07pd3371

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- The space shuttle Atlantis STS-122 crew poses for a group portrait at Launch Pad 39A as Atlantis undergoes final preparations for launch behind them. From left are Mission Specialists Hans Schlegel, Rex Walheim and Leland Melvin; Pilot Alan Poindexter; Commander Steve Frick; and Mission Specialists Stanley Love and Leopold Eyharts. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd3380

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- At the slidewire basket landing on Launch Pad 39A, the space shuttle Atlantis STS-122 crew poses for a group photo following a press conference. From left are Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialists Leland Melvin, Rex Walheim, Hans Schlegel, Stanley Love and Leopold Eyharts. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Red List of lampreys and marine fishes of the Wadden Sea

NASA Astrophysics Data System (ADS)

Berg, S.; Krog, C.; Muus, B.; Nielsen, J.; Fricke, R.; Berghahn, R.; Neudecker, Th.; Wolff, W. J.

1996-10-01

In the Wadden Sea areas of Denmark, Germany and The Netherlands, a total of 162 fish and lamprey species is known. 72 of these species are migrants entering the area occasionally; the total number of resident species in the Wadden Sea area is 90. In the Wadden Sea, in total, 20 species of fish and lamprey species are threatened in at least one subregion. Of these, 19 species are threatened in the entire area and are therefore placed on the trilateral Red List. 2 species of the listed fish and lamprey species are (probably) extinct in the entire Wadden Sea area. The status of 5 species of fish and lamprey species is critical, 5 species are (probably) endangered, the status of 6 is vulnerable and of 1 species susceptible. For about 16 rare species which may also be threatened, data were not sufficient to estimate past and present population sizes. The contributors to the list would like to encourage researchers to intensify work on the ecology and the present population sizes of these rare Wadden Sea species (see Fricke et al., 1995).

KSC-07pd3379

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- At the slidewire basket landing on Launch Pad 39A, the space shuttle Atlantis STS-122 crew responds to questions from the media. From left are Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialists Leland Melvin, Rex Walheim, Hans Schlegel (with the microphone), Stanley Love and Leopold Eyharts. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd3372

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- At the slidewire basket landing on Launch Pad 39A, the space shuttle Atlantis STS-122 crew responds to questions from the media. From left are Commander Steve Frick (with the microphone); Pilot Alan Poindexter; and Mission Specialists Leland Melvin, Rex Walheim, Hans Schlegel, Stanley Love and Leopold Eyharts. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd3378

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- At the slidewire basket landing on Launch Pad 39A, the space shuttle Atlantis STS-122 crew responds to questions from the media. From left are Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialists Leland Melvin, Rex Walheim (with the microphone), Hans Schlegel, Stanley Love and Leopold Eyharts. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Circulation Type Classifications and their nexus to Van Bebber's storm track Vb

NASA Astrophysics Data System (ADS)

Hofstätter, M.; Chimani, B.

2012-04-01

Circulation Type Classifications (CTCs) are tools to identify repetitive and predominantly stationary patterns of the atmospheric circulation over a certain area, with the purpose to enable the recognition of specific characteristics in surface climate variables. On the other hand storm tracks can be used to identify similar types of synoptic events from a non-stationary, kinematic perspective. Such a storm track classification for Europe has been done in the late 19th century by Van Bebber (1882, 1891), from which the famous type Vb and Vc/d remained up to the present day because of to their association with major flooding events like in August 2002 in Europe. In this work a systematic tracking procedure has been developed, to determine storm track types and their characteristics especially for the Eastern Alpine Region in the period 1961-2002, using ERA40 and ERAinterim reanalysis. The focus thereby is on cyclone tracks of type V as suggested by van Bebber and congeneric types. This new catalogue is used as a reference to verify the hypothesis of a certain coherence of storm track Vb with certain circulation types (e.g. Fricke and Kaminski, 2002). Selected objective and subjective classification schemes from the COST733 action (http://cost733.met.no/, Phillip et al. 2010) are used therefore, as well as the manual classification from ZAMG (Lauscher 1972 and 1985), in which storm track Vb has been classified explicitly on a daily base since 1948. The latter scheme should prove itself as a valuable and unique data source in that issue. Results show that not less than 146 storm tracks are identified as Vb between 1961 and 2002, whereas only three events could be found from literature, pointing to big subjectivity and preconception in the issue of Vb storm tracks. The annual number of Vb storm tracks do not show any significant trend over the last 42 years, but large variations from year to year. Circulation type classification CAP27 (Cluster Analysis of Principal Components) is the best performing, fully objective scheme tested herein, showing the power to discriminate Vb events. Most of the other fully objective schemes do by far not perform as well. Largest skill in that issue can be seen from the subjective/manual CTCs, proving themselves to enhance relevant synoptic phenomena instead of emphasizing mathematic criteria in the classification. The hypothesis of Fricke and Kaminsky can definitely be supported by this work: Vb storm tracks are included in one or the other stationary circulation pattern, but to which extent depends on the specific characteristics of the CTC in question.

The correction of time and temperature effects in MR-based 3D Fricke xylenol orange dosimetry.

PubMed

Welch, Mattea L; Jaffray, David A

2017-04-21

Previously developed MR-based three-dimensional (3D) Fricke-xylenol orange (FXG) dosimeters can provide end-to-end quality assurance and validation protocols for pre-clinical radiation platforms. FXG dosimeters quantify ionizing irradiation induced oxidation of Fe 2+ ions using pre- and post-irradiation MR imaging methods that detect changes in spin-lattice relaxation rates (R 1   =  [Formula: see text]) caused by irradiation induced oxidation of Fe 2+ . Chemical changes in MR-based FXG dosimeters that occur over time and with changes in temperature can decrease dosimetric accuracy if they are not properly characterized and corrected. This paper describes the characterization, development and utilization of an empirical model-based correction algorithm for time and temperature effects in the context of a pre-clinical irradiator and a 7 T pre-clinical MR imaging system. Time and temperature dependent changes of R 1 values were characterized using variable TR spin-echo imaging. R 1 -time and R 1 -temperature dependencies were fit using non-linear least squares fitting methods. Models were validated using leave-one-out cross-validation and resampling. Subsequently, a correction algorithm was developed that employed the previously fit empirical models to predict and reduce baseline R 1 shifts that occurred in the presence of time and temperature changes. The correction algorithm was tested on R 1 -dose response curves and 3D dose distributions delivered using a small animal irradiator at 225 kVp. The correction algorithm reduced baseline R 1 shifts from  -2.8  ×  10 -2 s -1 to 1.5  ×  10 -3 s -1 . In terms of absolute dosimetric performance as assessed with traceable standards, the correction algorithm reduced dose discrepancies from approximately 3% to approximately 0.5% (2.90  ±  2.08% to 0.20  ±  0.07%, and 2.68  ±  1.84% to 0.46  ±  0.37% for the 10  ×  10 and 8  ×  12 mm 2 fields, respectively). Chemical changes in MR-based FXG dosimeters produce time and temperature dependent R 1 values for the time intervals and temperature changes found in a typical small animal imaging and irradiation laboratory setting. These changes cause baseline R 1 shifts that negatively affect dosimeter accuracy. Characterization, modeling and correction of these effects improved in-field reported dose accuracy to less than 1% when compared to standardized ion chamber measurements.

Acute experimental hip muscle pain alters single-leg squat balance in healthy young adults.

PubMed

Hatton, Anna L; Crossley, Kay M; Hug, François; Bouma, James; Ha, Bonnie; Spaulding, Kara L; Tucker, Kylie

2015-05-01

Clinical musculoskeletal pain commonly accompanies hip pathology and can impact balance performance. Due to the cross-sectional designs of previous studies, and the multifactorial nature of musculoskeletal pain conditions, it is difficult to determine whether pain is a driver of balance impairments in this population. This study explored the effects of experimentally induced hip muscle pain on static and dynamic balance. Twelve healthy adults (4 women, mean[SD]: 27.1[3] years) performed three balance tasks on each leg, separately: single-leg standing (eyes closed), single-leg squat (eyes open), forward step (eyes open); before and after hypertonic saline injection (1ml, 5% NaCl) into the right gluteus medius. Range, standard deviation (SD), and velocity of the centre of pressure (CoP) in medio-lateral (ML) and anterior-posterior (AP) directions were considered. During the single-leg squat task, experimental hip pain was associated with significantly reduced ML range (-4[13]%, P=0.028), AP range (-14[21]%, P=0.005), APSD (-15[28]%, P=0.009), and AP velocity (-6[13]%, P=0.032), relative to the control condition, in both legs. No effect of pain was observed during single-leg standing and forward stepping. Significant between-leg differences in ML velocity were observed during the forward stepping task (P=0.034). Pain is a potentially modifiable patient-reported outcome in individuals with hip problems. This study demonstrates that acute hip muscle pain alone, without interference of musculoskeletal pathology, does not lead to the same impairments in balance as exhibited in clinical populations with hip pathologies. This is the first step in understanding how and why balance is altered in painful hip pathologies. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of sampling volume on dry powder inhaler (DPI)-emitted aerosol aerodynamic particle size distributions (APSDs) measured by the Next-Generation Pharmaceutical Impactor (NGI) and the Andersen eight-stage cascade impactor (ACI).

PubMed

Mohammed, Hlack; Roberts, Daryl L; Copley, Mark; Hammond, Mark; Nichols, Steven C; Mitchell, Jolyon P

2012-09-01

Current pharmacopeial methods for testing dry powder inhalers (DPIs) require that 4.0 L be drawn through the inhaler to quantify aerodynamic particle size distribution of "inhaled" particles. This volume comfortably exceeds the internal dead volume of the Andersen eight-stage cascade impactor (ACI) and Next Generation pharmaceutical Impactor (NGI) as designated multistage cascade impactors. Two DPIs, the second (DPI-B) having similar resistance than the first (DPI-A) were used to evaluate ACI and NGI performance at 60 L/min following the methodology described in the European and United States Pharmacopeias. At sampling times ≥2 s (equivalent to volumes ≥2.0 L), both impactors provided consistent measures of therapeutically important fine particle mass (FPM) from both DPIs, independent of sample duration. At shorter sample times, FPM decreased substantially with the NGI, indicative of incomplete aerosol bolus transfer through the system whose dead space was 2.025 L. However, the ACI provided consistent measures of both variables across the range of sampled volumes evaluated, even when this volume was less than 50% of its internal dead space of 1.155 L. Such behavior may be indicative of maldistribution of the flow profile from the relatively narrow exit of the induction port to the uppermost stage of the impactor at start-up. An explanation of the ACI anomalous behavior from first principles requires resolution of the rapidly changing unsteady flow and pressure conditions at start up, and is the subject of ongoing research by the European Pharmaceutical Aerosol Group. Meanwhile, these experimental findings are provided to advocate a prudent approach by retaining the current pharmacopeial methodology.

Measurement of complex permittivities of biological materials and human skin in vivo in the frequency band

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghodgaonkar, D.K.

1987-01-01

A new method, namely, modified infinite sample method, has been developed which is particularly suitable for millimeter-wave dielectric measurements of biological materials. In this method, an impedance transformer is used which reduces the reflectivity of the biological sample. Because of the effect of introducing impendance transformer, the measured reflection coefficients are more sensitive to the complex permittivities of biological samples. For accurate measurement of reflection coefficients, two automated measurment systems were developed which cover the frequencies range of 26.5-60 GHz. An uncertainty analysis was performed to get an estimate of the errors in the measured complex permittivities. The dielectric propertiesmore » were measured for 10% saline solution, whole human blood, 200 mg/ml bovine serum albumin (BSA) solution and suspension of Saccharomyces cerevisiae cells. The Maxwell-Fricke equation, which is derived from dielectric mixture theory, was used for determination bound water in BSA solution. The results of all biological samples were interpreted by fitting Debye relaxation and Cole-Cole model. It is observed that the dielectric data for the biological materials can be explained on the basis of Debye relaxation of water molecule.« less

Prevention of Transfusion-Associated Graft-versus-Host Disease by Irradiation: Technical Aspect of a New Ferrous Sulphate Dosimetric System

PubMed Central

Del Lama, Lucas Sacchini; de Góes, Evamberto Garcia; Petchevist, Paulo César Dias; Moretto, Edson Lara; Borges, José Carlos; Covas, Dimas Tadeu; de Almeida, Adelaide

2013-01-01

Irradiation of whole blood and blood components before transfusion is currently the only accepted method to prevent Transfusion-Associated Graft-Versus-Host-Disease (TA-GVHD). However, choosing the appropriate technique to determine the dosimetric parameters associated with blood irradiation remains an issue. We propose a dosimetric system based on the standard Fricke Xylenol Gel (FXG) dosimeter and an appropriate phantom. The modified dosimeter was previously calibrated using a 60Co teletherapy unit and its validation was accomplished with a 137Cs blood irradiator. An ionization chamber, standard FXG, radiochromic film and thermoluminescent dosimeters (TLDs) were used as reference dosimeters to determine the dose response and dose rate of the 60Co unit. The dose distributions in a blood irradiator were determined with the modified FXG, the radiochromic film, and measurements by TLD dosimeters. A linear response for absorbed doses up to 54 Gy was obtained with our system. Additionally, the dose rate uncertainties carried out with gel dosimetry were lower than 5% and differences lower than 4% were noted when the absorbed dose responses were compared with ionization chamber, film and TLDs. PMID:23762345

Studies on heavy charged particle interaction, water equivalence and Monte Carlo simulation in some gel dosimeters, water, human tissues and water phantoms

NASA Astrophysics Data System (ADS)

Kurudirek, Murat

2015-09-01

Some gel dosimeters, water, human tissues and water phantoms were investigated with respect to their radiological properties in the energy region 10 keV-10 MeV. The effective atomic numbers (Zeff) and electron densities (Ne) for some heavy charged particles such as protons, He ions, B ions and C ions have been calculated for the first time for Fricke, MAGIC, MAGAT, PAGAT, PRESAGE, water, adipose tissue, muscle skeletal (ICRP), muscle striated (ICRU), plastic water, WT1 and RW3 using mass stopping powers from SRIM Monte Carlo software. The ranges and straggling were also calculated for the given materials. Two different set of mass stopping powers were used to calculate Zeff for comparison. The water equivalence of the given materials was also determined based on the results obtained. The Monte Carlo simulation of the charged particle transport was also done using SRIM code. The heavy ion distribution along with its parameters were shown for the given materials for different heavy ions. Also the energy loss and damage events in water when irradiated with 100 keV heavy ions were studied in detail.

The effects of rotation on the surface composition and yields of low mass AGB stars.

NASA Astrophysics Data System (ADS)

Cristallo, S.; Piersanti, L.; Straniero, O.

Over the past 20 years, stellar evolutionary models have been strongly improved in order to reproduce with reasonable accuracy both photometric and spectroscopic observations. Notwithstanding, the majority of these models do not take into account macroscopic phenomena, like rotation and/or magnetic fields. Their explicit treatment could modify stellar physical and chemical properties. One of the most interesting problems related to stellar nucleosynthesis is the behavior of the s-process spectroscopic indexes ([hs/ls] and [Pb/hs]) in Asymptotic Giant Branch (AGB) stars. In this contribution we show that, for a fixed metallicity, rotation can lead to a spread in the [hs/ls] and [Pb/hs] in low-mass AGB stars. In particular, we demonstrate that the Eddington-Sweet and the Goldreich-Schubert-Fricke instabilities may have enough time to smear the 13C-pocket (the major neutron source) and the 14N-pocket (the major neutron poison). In fact, a different overlap between these pockets leads to a different neutrons-to-seeds ratio, with important consequences on the corresponding s-process distributions. Possible consequences on the chemical evolution of Galactic globular clusters are discussed.

KSC-08pd0405

NASA Image and Video Library

2008-02-20

KENNEDY SPACE CENTER, FLA. -- After exiting the crew transport vehicle on the Shuttle Landing Facility at NASA's Kennedy Space Center, the STS-122 crew stands in front of space shuttle Atlantis to greet the media and guests. At the microphone is Commander Steve Frick. Behind him, left to right, are Mission Specialists Leland Melvin, Hans Schlegel, Rex Walheim (not visible) and Stanley Love, and Pilot Alan Poindexter. Schlegel represents the European Space Agency. After a round trip of nearly 5.3 million miles, space shuttle Atlantis and crew returned to Earth with a landing at 9:07 a.m. EST. The shuttle landed on orbit 202 to complete the 13-day STS-122 mission. Main gear touchdown was 9:07:10 a.m. Nose gear touchdown was 9:07:20 a.m. Wheel stop was at 9:08:08 a.m. Mission elapsed time was 12 days, 18 hours, 21 minutes and 44 seconds. During the mission, Atlantis' crew installed the new Columbus laboratory, leaving a larger space station and one with increased science capabilities. The Columbus Research Module adds nearly 1,000 cubic feet of habitable volume and affords room for 10 experiment racks, each an independent science lab. Photo credit: NASA/Jack Pfaller

First record of the Indo-Pacific areolate grouper Epinephelus areolatus (Forsskål, 1775) (Perciformes: Epinephelidae) in the Mediterranean Sea.

PubMed

Rothman, Shevy B S; Stern, Nir; Goren, Menachem

2016-01-25

The number of alien species in the Mediterranean Sea is steadily increasing and it seems that the pace has been accelerating since the turn of the century (Galil et al. 2014). In 2015 alone five additional fish species have been reported, Epinephelus geoffroyi (Klunzinger, 1870) (Golani et al. 2015); Stolephorus indicus (van Hasselt, 1823) (Fricke et al. 2015); Sardinella gibbosa (Bleeker, 1849) (Stern et al. 2015); Mobula japanica (Müller & Henle, 1841) (Capapé et al. 2015); and Cryptocentrus caeruleopunctatus (Rüppell, 1830) (Rothman & Goren 2015). Among the ca. 100 alien fish species reported from the Mediterranean to date (Galil & Goren 2014), five Indo-Pacific species belong to the genus Epinephelus Bloch, 1793: Epinephelus coioides (Hamilton, 1822), Epinephelus fasciatus (Forsskål, 1775), Epinephelus malabaricus (Bloch and Schneider, 1804) Epinephelus merra Bloch, 1793 (Golani et al. 2013a) and Epinephelus geoffroyi (Klunzinger, 1870) (Golani et al. 2015). Additional alien Epinephelus species reported from the Mediterranean are excluded for various reasons (Golani et al. 2013b). Here we report the finding of a sixth Indo-Pacific species of this genus along the Mediterranean coast of Israel.

KSC-07pd3351

NASA Image and Video Library

2007-11-18

KENNEDY SPACE CENTER, FLA. -- The STS-122 crew poses for a group portrait near Launch Pad 39B following a training session on the operation of the M-113 armored personnel carrier. An M-113 will be available to transport the crew to safety in the event of an emergency on the pad before their launch. From left are Mission Specialists Rex Walheim and Stanley Love; Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialists Leland Melvin, Leopold Eyharts and Hans Schlegel. Eyharts and Schlegel are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The crew is participating in Terminal Countdown Demonstration Test activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization, emergency egress training and a simulated launch countdown. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Fecal-coliform bacteria concentrations in streams of the Chattahoochee River National Recreation Area, Metropolitan Atlanta, Georgia, May-October 1994 and 1995

USGS Publications Warehouse

Gregory, M. Brian; Frick, Elizabeth A.

2000-01-01

Introduction: The Metropolitan Atlanta area has been undergoing a period of rapid growth and development. The population in the 10-county metropolitan area almost doubled from about 1.5 million people in 1970 to 2.9 million people in 1995 (Atlanta Regional Commission, written commun., 2000). Residential, commercial, and other urban land uses more than tripled during the same period (Frick and others, 1998). The Chattahoochee River is the most utilized water resource in Georgia. The rapid growth of Metropolitan Atlanta and its location downstream of the headwaters of the drainage basin make the Chattahoochee River a vital resource for drinking-water supplies, recreational opportunities, and wastewater assimilation. In 1978, the U.S. Congress declared the natural, scenic, recreation, and other values of 48 miles of the Chattahoochee River from Buford Dam to Peachtree Creek to be of special national significance. To preserve this reach of the Chattahoochee River, the U.S. Congress created the Chattahoochee River National Recreational Area (CRNRA), which includes the Chattahoochee River downstream from Buford Dam to the mouth of Peachtree Creek and a series of park areas adjacent to the river in northern Metropolitan Atlanta Even with this protection, waters of the Chattahoochee River and many of its tributaries in Metropolitan Atlanta did not meet water-quality standards set for designated uses during 1994 and 1995 (fig. 1 and table 1). Much of the degradation of water quality has been associated with areas undergoing rapid urban growth and sprawling suburban development. The resulting conversion of mostly forested land to urban land has multiple adverse effects on water quality. Degradation of water quality may be caused by a number of factors including an increase in nutrient concentrations, sediment and sedimentbound contaminant concentrations (e.g., metals and pesticides) (Frick and others, 1998), and fecal-coliform bacteria concentrations (Center for Watershed Protection, 1999). The presence of fecal-coliform bacteria in streams and rivers indicates that contamination by fecal material from human or animal sources has occurred and contact with these waters can result in exposure to pathogenic bacteria often associated with fecal contamination. During 1994 and 1995, elevated concentrations of fecal-coliform bacteria were the most common reason that the Chattahoochee River and tributaries did not meet their designated uses of drinking-water supply, recreation, and fishing. According to the Georgia Department of Natural Resources (1997), during 1994 and 1995, 67 of 77 stream reaches assessed in Metropolitan Atlanta did not meet or only partially met water-quality requirements for designated uses. Excessive concentrations of fecal-coliform bacteria were a contributing factor in 63 of the 67 streams that did not meet or only partially met designated uses. High concentrations of fecal-coliform bacteria have the potential to reduce the recreational value of the river and pose a continued threat, with unknown health risks, to humans that come in contact with the water while fishing, boating, rafting, wading, and swimming.

Energy characterisation of ultrasonic systems for industrial processes.

PubMed

Al-Juboori, Raed A; Yusaf, Talal; Bowtell, Leslie; Aravinthan, Vasantha

2015-03-01

Obtaining accurate power characteristics of ultrasonic treatment systems is an important step towards their industrial scalability. Calorimetric measurements are most commonly used for quantifying the dissipated ultrasonic power. However, accuracy of these measurements is affected by various heat losses, especially when working at high power densities. In this work, electrical power measurements were conducted at all locations in the piezoelectric ultrasonic system equipped with ½″ and ¾″ probes. A set of heat transfer calculations were developed to estimate the convection heat losses from the reaction solution. Chemical dosimeters represented by the oxidation of potassium iodide, Fricke solution and 4-nitrophenol were used to chemically correlate the effect of various electrical amplitudes and treatment regimes. This allowed estimation of sonochemical-efficiency (SE) and energy conversion (XUS) of the ultrasonic system. Results of this study showed overall conversion efficiencies of 60-70%. This correlated well with the chemical dosimeter yield curves of both organic and inorganic aqueous solutions. All dosimeters showed bubble shielding and coalescence effects at higher ultrasonic power levels, less pronounced for the ½″ probe case. SE and XUS values in the range of 10(-10) mol/J and 10(-3) J/J respectively confirmed that conversion of ultrasonic power to chemical yield declined with amplitude. Copyright © 2014 Elsevier B.V. All rights reserved.

[Application of the method of one-day learning in a Morris water maze to analyse the effects of sleep deprivation on memory trace recall 24 hours later, after learning].

PubMed

Dorokhov, V B; Kozhedub, R G; Arsenyev, G N; Bukhgolts, O I; Marchenko, V G; Puchkova, A N

2014-01-01

The proposed model of a one-day spatial learning is of interest in research of how sleep influences the hippocamp-dependent memory consolidation. We have studied the influence of a one-day total sleep deprivation on spatial memory consolidation in hooded rats after a one-day learning in the Morris water maze according to Feldman et al. [2010] protocol. According to it rats had to find a submerged platform that was alternatively marked by a flag or completely invisible to an animal. In a previous study [Dorokhov et al., 2011] we have used another one-day learning protocol [Frick et al., 2000] and Wistar rats and have demonstrated a large interindividual variance in learning parameters and sleep deprivation effects on memory consolidation. In this study we confirm previously acquired results on negative impact of sleep deprivation on spatial memory consolidation. To demonstrate the effects of sleep deprivation on the results of one-day learning we are using for the first time an evaluation of the time spent by an animal in the area of the platform placement and corresponding areas in the other quadrants of the water maze.

Dose rate effect of pulsed electron beam on micronucleus frequency in human peripheral blood lymphocytes.

PubMed

Acharya, Santhosh; Sanjeev, Ganesh; Bhat, Nagesh N; Narayana, Yerol

2010-03-01

The micronucleus assay in human peripheral blood lymphocytes is a sensitive indicator of radiation damage and could serve as a biological dosimeter in evaluating suspected overexposure to ionising radiation. Micronucleus (MN) frequency as a measure of chromosomal damage has also extensively been employed to quantify the effects of radiation dose rate on biological systems. Here we studied the effects of 8 MeV pulsed electron beam emitted by Microtron electron accelerator on MN induction at dose rates between 35 Gy min-1 and 352.5 Gy min-1. These dose rates were achieved by varying the pulse repetition rate (PRR). Fricke dosimeter was employed to measure the absorbed dose at different PRR and to ensure uniform dose distribution of the electron beam. To study the dose rate effect, blood samples were irradiated to an absorbed dose of (4.7+/-0.2) Gy at different rates and cytogenetic damage was quantified using the micronucleus assay. The obtained MN frequency showed no dose rate dependence within the studied dose rate range. Our earlier dose effect study using 8 MeV electrons revealed that the response of MN was linear-quadratic. Therefore, in the event of an accident, dose estimation can be made using linear-quadratic dose response parameters, without adding dose rate as a correction factor.

[The costs of new drugs compared to current standard treatment].

PubMed

Ujeyl, Mariam; Schlegel, Claudia; Gundert-Remy, Ursula

2013-01-01

Until AMNOG came into effect Germany had free pricing of new drugs. Our exemplary work investigates the costs of new drugs that were licensed in the two years prior to AMNOG, and compares them to the costs of standard treatment that has been used in pivotal trials. Also, the important components of pharmaceutical prices will be illustrated. We retrospectively analysed the European Public Assessment Reports of proprietary medicinal products that the European Medicinal Agency initially approved in 2009 and 2010 and that were tested against an active control in at least one pivotal trial. If the standard treatment was a generic, the average pharmacy retail price of new drugs was 7.4 times (median 7.1) higher than that of standard treatment. If the standard treatment was an originator drug the average price was 1.4 times (median 1.2) higher than that of the new drug. There was no clear correlation of an increase in costs for new drugs and their "grade of innovation" as rated according to the criteria of Fricke. Our study shows that prices of new drugs must be linked to the evidence of comparative benefit; since German drug pricing is complex, cost saving effects obtained thereby will depend on a range of other rules and decisions. Copyright © 2013. Published by Elsevier GmbH.

[The effect of ivermectin on geohelminth frequency (i.e. as used in the onchocerciasis control program in Colombia)].

PubMed

Knudson, Angélica; Ariza, Yoseth; López, Myriam C; Fajardo, Oscar S; Reyes, Patricia; Moncada, Ligia I; Duque, Sofía; Álvarez, Carlos A; Nicholls, Rubén S

2012-08-01

Evaluating the effect of ivermectin on soil-transmitted helminthes (STH) infection frequency in a Colombian population included in the Onchocerciasis Elimination Program for the Americas (OEPA). This was an impact evaluation study which adopted a longitudinal approach using the population of Naicioná (1996) as baseline for comparison to people from the same population as controls (2008). The cross-sectional approach involved comparing the reference population of Naicioná (2008) to the population of Dos Quebradas (2008) used as controls. Fecal samples were processed by a modified Ritchie-Frick method. Ascaris lumbricoides was the most frequently found parasite in Naicioná (60/121; 49.6 %: 37.8-63.895%CI) and in Dos Quebradas (36/76; 47.4 %: 33.2-65.6 95 % CI). Ivermectin's main effect on the population aged over 5 years was a decreased risk of Trichiuris trichiura infection in both longitudinal assessment (86 % reduction: 74-93 95 % CI) and cross-sectional assessment (63 %:24-82 95 % CI). A 93 % reduction (45-99 95 % CI) in Strongyloides stercoralis frequency was found in longitudinal assessment, compared to 85 % in cross-sectional assessment (-031-99 95 % CI). Ivermectin use in the OEPA is not sufficient for STH morbidity control. Integrated programs including education and basic sanitation are required.

KSC-07pd3452

NASA Image and Video Library

2007-11-20

KENNEDY SPACE CENTER, FLA. -- Members of space shuttle Atlantis' STS-122 crew pose for a group portrait in front of Atlantis' external tank following a simulated launch countdown at Launch Pad 39A. From left are Mission Specialists Rex Walheim and Leland Melvin; Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialists Leopold Eyharts, Stanley Love and Hans Schlegel. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The exercise is part of terminal countdown demonstration test, or TCDT, activities at NASA's Kennedy Space Center. The TCDT is a dress rehearsal for launch and also provides astronauts and ground crews with equipment familiarization and emergency egress training. On mission STS-122, Atlantis will deliver the Columbus module to the International Space Station. The European Space Agency's largest single contribution to the station, Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony. The laboratory will expand the research facilities aboard the station, providing crew members and scientists from around the world the ability to conduct a variety of experiments in the physical, materials and life sciences. Atlantis' launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd3451

NASA Image and Video Library

2007-11-20

KENNEDY SPACE CENTER, FLA. -- Members of space shuttle Atlantis' STS-122 crew pose for a group portrait with the tip of Atlantis' external tank in the background following a simulated launch countdown at Launch Pad 39A. From left are Mission Specialists Rex Walheim and Leland Melvin; Commander Steve Frick; Pilot Alan Poindexter; and Mission Specialists Leopold Eyharts, Stanley Love and Hans Schlegel. Schlegel and Eyharts are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The exercise is part of terminal countdown demonstration test, or TCDT, activities at NASA's Kennedy Space Center. The TCDT is a dress rehearsal for launch and also provides astronauts and ground crews with equipment familiarization and emergency egress training. On mission STS-122, Atlantis will deliver the Columbus module to the International Space Station. The European Space Agency's largest single contribution to the station, Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony. The laboratory will expand the research facilities aboard the station, providing crew members and scientists from around the world the ability to conduct a variety of experiments in the physical, materials and life sciences. Atlantis' launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Probing the particulate microstructure of the aerodynamic particle size distribution of dry powder inhaler combination products.

PubMed

Jetzer, M W; Morrical, B D; Schneider, M; Edge, S; Imanidis, G

2018-03-01

The in-vitro aerosol performance of two combination dry powder inhaler (DPI) products, Foster ® NEXThaler ® and Seretide ® Diskus ® were investigated with single particle aerosol mass spectrometry (SPAMS). The in-vitro pharmaceutical performance is markedly different for both inhalers. Foster ® NEXThaler ® generates a higher fine particle fraction (FPF <5 μm) and a much higher relative extra fine particle fraction (eFPF <2 μm). In terms of the composition of the aerodynamic particle size distribution (APSD), it could be verified with SPAMS that overall Foster ® NEXThaler ® emits a significantly higher number of fine and extra fine particles with a median aerodynamic diameter (MAD) of 2.1 μm while Seretide ® Diskus ® had a larger MAD of 3.1 μm. Additionally, the interactions between the two active pharmaceutical ingredients (APIs) in both products are different. While Seretide ® Diskus ® emits a significant (37%) number of co-associated API particles, only a negligible number of co-associated API particles were found in Foster ® NEXThaler ® (<1%). A major difference with Foster ® NEXThaler ® is that it contains magnesium stearate (MgSt) as a second excipient besides lactose in a so-called 'dual excipient' platform. The data generated using SPAMS suggested that nearly all of the beclomethasone dipropionate particles in Foster ® NEXThaler ® also contain MgSt and must therefore be co-associated with this additional excipient. This may help explain why beclomethasone dipropionate in Foster ® NEXThaler ® forms less particle co-associations with the second API, formoterol fumarate, shows a lower cohesive strength in respect to beclomethasone itself and why both APIs exhibit superior detachment from the carrier as evidenced by the increased eFPF and smaller MAD. Copyright © 2018 Elsevier B.V. All rights reserved.

Functional Uncoupling NMDAR NR2A Subunit from PSD-95 in the Prefrontal Cortex: Effects on Behavioral Dysfunction and Parvalbumin Loss after Early-Life Stress

PubMed Central

Ganguly, Prabarna; Holland, Freedom H; Brenhouse, Heather C

2015-01-01

Exposure to early-life stress increases vulnerability to psychiatric disorders, including depression, schizophrenia, and anxiety. Growing evidence implicates aberrant development of the prefrontal cortex (PFC) in the effects of early-life stress, which often emerge in adolescence or young adulthood. Specifically, early-life stress in the form of maternal separation (MS) in rodents has been shown to decrease parvalbumin (PVB)-positive interneurons in the adolescent PFC; however, the mechanism underpinning behavioral dysfunction and PVB loss is not yet known. We recently reported that MS causes overexpression of the NMDA subunit NR2A in the PFC of adolescent rats. Elevated PFC NR2A is also found in developmental models of schizophrenia and is correlated with behavioral deficits, acting largely through its association with the postsynaptic protein PSD-95. In addition, adolescent maturation of PVB-positive interneurons relies on NR2A-driven NMDA activity. Therefore, it is possible that the NR2A/PSD-95 signaling complex has a role in adolescent MS effects. Here, we aimed to determine whether a discrete manipulation of PFC NR2A could prevent MS effects on PFC-controlled behaviors, including cognition, anxiety, and novelty-induced hyperlocomotion, as well as PVB loss in adolescence. We intracranially infused the NR2A-specific blocking peptide TAT2A in order to uncouple NR2A from PSD-95 in the early-adolescent PFC, without antagonizing the NMDA receptor. We demonstrated that MS rats treated with TAT2A during early adolescence were protected from MS-induced PVB loss and exhibited less anxious behavior than those infused with control peptide. These data implicate NR2A-related N-methyl-D-aspartate receptor development in adolescent behavioral and neural consequences of early-life stress. PMID:25953359

Sedimentological, climatic and environmental changes during the Early Jurassic (Hettangian-Pliensbachian) on the northern Tethyan margin (Switzerland)

NASA Astrophysics Data System (ADS)

Schöllhorn, Iris; Foellmi, Karl; adatte, Thierry

2016-04-01

The Early Jurassic interval witnessed different phases of paleoenvironmental change, starting with the end-Triassic mass extinction event, c. 201.4 Ma ago, which was marked by terrestrial ecosystem turnover, up to 50% loss in marine biodiversity and large turnovers in global geochemical cycles linked to the onset of Central Atlantic Magmatic Province volcanism (Raup et Sepkosky, 1982 ; Hesselbo et al., 2002 ; Deenen et al., 2010). This time interval saw equally a phase of major climate change near the Pliensbachian-Toarcian boundary, which was followed by the Early Toarcian oceanic anoxic episode (e.g., Suan et al., 2010). Previous studies mainly focused on these major and short-lived events, while the remaining intervals of the Early Jurassic received significantly less attention. Therefore, in this study, we examine the sedimentological, geochemical and environmental changes between these events on the northern Tethyan margin (Swiss Jura). With this purpose, a wide array of geochemical analyses (carbon isotope, Rock-Eval, phosphorus content, mineralogy, trace and major element content and clay analyses) and sedimentary observations has been performed on four sections and cores (Frick, Riniken, Pfaffnau and Kreuzlingen). We observed two depositional systems: (1) the Schambelen Member (lower Hettangian) and the Frick Mb. (middle Upper Sinemurian), which are characterised by organic-rich shales intercalated by tempestites; and (2) the Beggingen Member (Upper Hettangian to Lower Sinemurian) and the Grünscholz, Breitenmatt and Rietheim Members (upper Upper Sinemurian to Pliensbachian), which are composed of carbonates marked by the presence of hiati, condensed beds, phosphate- and fossil-rich strata, and erosional features, which testify to a dynamic environment characterised by overall low sediment-accumulation rates. The clay fraction, composed mainly of kaolinite, chlorite and illite, was controlled by various parameters. The rise of kaolinite in the Late Sinemurian was probably caused by a shallowing-up also shown by a decrease in phyllosilicates and an increase in the quartz content in the whole rock. The related sea-level change is probably linked to tectonically induced regional tilting. The lowest kaolinite contents are observed in the condensed sections where important remobilisation took place. The isotope and rock-eval analyses reveal also important environmental changes: (a) Two negative carbon isotope excursions measured on organic matter (CIEorg -2‰) are observed during the Early Hettangian accompanied by a change in organic matter composition, higher productivity (high hydrogen indices), anoxia (high trace element, pyrite and organic matter contents and presence of pyrite framboids; cf. also Schwab and Spangenberg, 2006) and higher weathering rates (CIA and clay mineralogy). (b) The Early Sinemurian is characterised by a +4‰ CIEorg in this sections. Nevertheless, the globality and causes of this CIE remain to be determined. (c) The Sinemurian-Pliensbachian boundary record a negative CIEorg (-3‰), followed by a positive CIE (+2‰) during the Early-Late Pliensbachian and a negative CIEorg (-1.5‰) during the Late Pliensbachian. These CIEs are also recorded in several other localities in carbonates, belemnites, wood and organic matter, and result likely from global events. These CIEs are linked to OM preservation and/or productivity changes and/or 13C-depleted carbon input(s).

Green synthesis of silver nanoparticles aimed at improving theranostics

NASA Astrophysics Data System (ADS)

Vedelago, José; Gomez, Cesar G.; Valente, Mauro; Mattea, Facundo

2018-05-01

Nowadays, the combination of diagnosis and therapy, known as theranostics, is one of the keys for an optimal treatment for cancer diseases. Theranostics can be significantly improved by incorporating metallic nanoparticles that are specifically delivered and accumulated in cancerous tissue. In this context, precise knowledge about dosimetric effects in nanoparticle-infused tissues as well as the detection and processing of emerging radiation are extremely important issues. In the last years the first studies on theranostic nanomaterials in gel dosimetry have been presented but there is still a broad field of study to explore. Most of gel dosimetric materials are extremely sensible to modifications in their composition, the addition of enhancers, metallic or inorganic charges can alter their stability and dosimetric properties; therefore, thorough studies must be made before the incorporation of any type of modifier. In this work, the synthesis of metallic nanoparticles suitable for gel dosimetry for x-ray applications is presented. A green synthesis process of silver nanoparticles coated with porcine skin gelatin by thermal reduction of silver nitrate is presented. Nanoparticles were obtained and purified for their application in gel dosimetry. Also, nanoparticles size distribution, reaction yield and the preliminar application as theranostic agents were tested in Fricke gel dosimetry in the keV range. The obtained nanoparticles were successfully used in theranostic applications acting as fluorescent agents and dose enhancers in X-ray beam irradiation simultaneously.

Inhibition of Pseudogymnoascus destructans growth from conidia and mycelial extension by bacterially produced volatile organic compounds.

PubMed

Cornelison, Christopher T; Gabriel, Kyle T; Barlament, Courtney; Crow, Sidney A

2014-02-01

The recently identified causative agent of white-nose syndrome (WNS), Pseudogymnoascus destructans, has been implicated in the mortality of an estimated 5.5 million North American bats since its initial documentation in 2006 (Frick et al. in Science 329:679-682, 2010). In an effort to identify potential biological and chemical control options for WNS, 6 previously described bacterially produced volatile organic compounds (VOCs) were screened for anti-P. destructans activity. The compounds include decanal; 2-ethyl-1-hexanol; nonanal; benzothiazole; benzaldehyde; andN,N-dimethyloctylamine. P. destructans conidia and mycelial plugs were exposed to the VOCs in a closed air space at 15 and 4 °C and then evaluated for growth inhibition. All VOCs inhibited growth from conidia as well as inhibiting radial mycelial extension, with the greatest effect at 4 °C. Studies of the ecology of fungistatic soils and the natural abundance of the fungistatic VOCs present in these environments suggest a synergistic activity of select VOCs may occur. The evaluation of formulations of two or three VOCs at equivalent concentrations was supportive of synergistic activity in several cases. The identification of bacterially produced VOCs with anti-P. destructans activity indicates disease-suppressive and fungistatic soils as a potentially significant reservoir of biological and chemical control options for WNS and provides wildlife management personnel with tools to combat this devastating disease.

Assessing invariance across sex and race/ethnicity in measures of youth psychopathic characteristics.

PubMed

Horan, Jacqueline M; Brown, Joshua L; Jones, Stephanie M; Aber, J Lawrence

2015-06-01

The aim of this study was to assess the measurement invariance of 2 commonly used measures of youth psychopathic characteristics across sex and racial/ethnic groups. Among a community sample of Hispanic and Black adolescents (N = 355; 50.5% female; mean age = 15.09) and their parents, this study tested the configural and metric invariance of the Levenson Self-Report Psychopathy Scale (LSRP; Levenson, Fitzpatrick, & Kiehl, 1995) and the parent-report version of the Inventory of Callous-Unemotional Traits (Frick, 2004). Preliminary analyses indicated that the adolescents in the present study reported similar rates of psychopathic characteristics as those reported by other studies of adolescents and young adults. Results of the multigroup invariance analyses indicated that these measures are invariant across sex and between Hispanic and Black youth. In addition, further analyses assessing associations between these measures and a number of behavioral and emotional characteristics indicated that scores on the LSRP Scale and Callous-Unemotional Traits demonstrate good convergent and discriminant validity with few differences by sex or race/ethnicity. To date, research on psychopathy has focused predominantly on samples of White males. Therefore, it is important that research examines the equivalence of measures of psychopathic characteristics across different populations, so that accurate assessments can be made to inform intervention and treatment efforts. (c) 2015 APA, all rights reserved).

KSC-07pd3391

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- During a training session on emergency exit from the fixed service structure on Launch Pad 39A, space shuttle Atlantis STS-122 Commander Steve Frick, left, and Mission Specialist Leland Melvin watch a slidewire basket descend to the landing zone. Seven slidewire baskets are available to carry the crew from the level of the pad's Orbiter Access Arm to a safe landing site below, if needed. Each basket can hold up to three people. A braking system catch net and drag chain slow, and then halt, the baskets as they travel down the wire at approximately 55 miles per hour. The journey takes about half a minute. A bunker is located in the landing zone 1,200 feet west of the pad, with an M-113 armored personnel carrier stationed nearby. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization and a simulated launch countdown before launch. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Calcium antagonists. A role in the management of cyanide poisoning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maduh, E.U.; Porter, D.W.; Baskin, S.I.

1993-12-31

The physiological role of calcium was demonstrated by Ringer (1883) when he linked the omission of calcium (Ca++) from the bathing medium to the induction of cardiac arrest in the isolated frog heart. This observation established that Ca++ controlled muscle contraction but it was not until the autumn of 1963 that the specific pharmacological significance of this contribution was realised by Fleckenstein (1964), leading to the development of Ca++ antagonism as a concept in drug action (Fleckenstein 1977). Identifying the precise role of Ca++ ions in toxic cell injury and tissue death attributable to drug and chemical intoxication has laggedmore » behind developments in Ca++ physiology and pharmacology and to date, much remains to be learned, although studies aimed at characterising the role of Ca++ in cytotoxic cell injury are receiving intense attention (Bondy Komulainen 1988; Maduh et al. l988a, l99Oa,b; Orrenius et al. 1989; Trump et al. 1989). On the other hand, the importance of cyanide as a poison has been known from antiquity (for references to earlier literature see Baskin Fricke 1992; Solomonson 1981). In experimental cyanide poisoning, recent studies have examined alterations in cell Ca++ and the influence of Ca++ antagonists in the management of this chemical toxicological emergency. These efforts have principally focused on the cellular Ca++ homeostasis system, its interrelationship with cellular components, and its susceptibility to cyanide action.« less

KSC-07pd3419

NASA Image and Video Library

2007-11-20

KENNEDY SPACE CENTER, FLA. -- Dressed in their launch and entry suits, the space shuttle Atlantis STS-122 crew poses for a group portrait in front of the astronaut van as they leave the Operations and Checkout Building for Launch Pad 39A. From left are Mission Specialists Leopold Eyharts, Stanley Love, Hans Schlegel, Rex Walheim, and Leland Melvin; Pilot Alan Poindexter; and Commander Steve Frick. Eyharts and Schlegel are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. The STS-122 crew is preparing for a simulated launch countdown aboard Atlantis, part of terminal countdown demonstration test, or TCDT, activities at NASA's Kennedy Space Center. The TCDT is a dress rehearsal for launch and also provides astronauts and ground crews with equipment familiarization and emergency egress training. On mission STS-122, Atlantis will deliver the Columbus module to the International Space Station. The European Space Agency's largest single contribution to the station, Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony. The laboratory will expand the research facilities aboard the station, providing crew members and scientists from around the world the ability to conduct a variety of experiments in the physical, materials and life sciences. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Current Mode Neutron Noise Measurements in the Zero Power Reactor CROCUS

NASA Astrophysics Data System (ADS)

Pakari, O.; Lamirand, V.; Perret, G.; Braun, L.; Frajtag, P.; Pautz, A.

2018-01-01

The present article is an overview of developments and results regarding neutron noise measurements in current mode at the CROCUS zero power facility. Neutron noise measurements offer a non-invasive method to determine kinetic reactor parameters such as the prompt decay constant at criticality α = βeff / λ, the effective delayed neutron fraction βeff, and the mean generation time λ for code validation efforts. At higher detection rates, i.e. above 2×104 cps in the used configuration at 0.1 W, the previously employed pulse charge amplification electronics with BF3 detectors yielded erroneous results due to dead time effects. Future experimental needs call for higher sensitivity in detectors, higher detection rates or higher reactor powers, and thus a generally more versatile measurement system. We, therefore, explored detectors operated with current mode acquisition electronics to accommodate the need. We approached the matter in two ways: 1) By using the two compensated 10B-coated ionization chambers available in CROCUS as operational monitors. The compensated current signal of these chambers was extracted from coremonitoring output channels. 2) By developing a new current mode amplification station to be used with other available detectors in core. Characteristics and first noise measurements of the new current system are presented. We implemented post-processing of the current signals from 1)and 2) with the APSD/CPSD method to determine α. At two critical states (0.5 and 1.5 W), using the 10B ionization chambers and their CPSD estimate, the prompt decay constant was measured after 1.5 hours to be α=(156.9 ± 4.3) s-1 (1σ). This result is within 1σ of statistical uncertainties of previous experiments and MCNPv5-1.6 predictions using the ENDF/B-7.1 library. The newsystem connected to a CFUL01 fission chamber using the APSDestimate at 100 mW after 33 min yielded α = (160.8 ± 6.3) s-1, also within 1σ agreement. The improvements to previous neutron noise measurementsinclude shorter measurement durations that can achievecomparable statistical uncertainties and measurements at higherdetection rates.

Natural mineral waters, curative-medical waters and their protection

NASA Astrophysics Data System (ADS)

Fricke, M.

1993-10-01

In Europe different types of water are marketed, each strictly defined by EC Directive 80/777 (Natural Mineral Water, Spring and Table Water) or 80/778 (Drinking Water). In Germany, an additional type of water is common in the market: curative/medical water. Product quality and safety, registration as medicine, and pharmaceutical control are defined by the German Federal Medicine Act. A medical water is treated as any other medicine and may be sold only in pharmacies. The use of any water in Germany is controlled and strictly regulated by the Federal Water Act (Fricke 1981). The following requirements are set by the act: (1) No water use without a permit, which is limited in time and quantity. (2) No single or juristic person may own water. (3) Water resources of public interest and their recharge areas are to be protected by the definition of water protection zones. (Natural mineral water is not of public interest and therefore is not required to be protected by the definition of water protection zones, although it represents a market value of more than US2 billion. Medical water is of public interest). The definition of water protection zones impacts private property rights and has to be handled carefully. In order to protect water resources, sometimes the economic basis of a traditional industrial and/or agricultural infrastructure is destroyed. The concerns and needs all citizens, including industry, must be considered in analyzing the adequacy of water protection zones.

Effective atomic numbers and electron densities of some human tissues and dosimetric materials for mean energies of various radiation sources relevant to radiotherapy and medical applications

NASA Astrophysics Data System (ADS)

Kurudirek, Murat

2014-09-01

Effective atomic numbers, Zeff, and electron densities, neff, are convenient parameters used to characterise the radiation response of a multi-element material in many technical and medical applications. Accurate values of these physical parameters provide essential data in medical physics. In the present study, the effective atomic numbers and electron densities have been calculated for some human tissues and dosimetric materials such as Adipose Tissue (ICRU-44), Bone Cortical (ICRU-44), Brain Grey/White Matter (ICRU-44), Breast Tissue (ICRU-44), Lung Tissue (ICRU-44), Soft Tissue (ICRU-44), LiF TLD-100H, TLD-100, Water, Borosilicate Glass, PAG (Gel Dosimeter), Fricke (Gel Dosimeter) and OSL (Aluminium Oxide) using mean photon energies, Em, of various radiation sources. The used radiation sources are Pd-103, Tc-99, Ra-226, I-131, Ir-192, Co-60, 30 kVp, 40 kVp, 50 kVp (Intrabeam, Carl Zeiss Meditec) and 6 MV (Mohan-6 MV) sources. The Em values were then used to calculate Zeff and neff of the tissues and dosimetric materials for various radiation sources. Different calculation methods for Zeff such as the direct method, the interpolation method and Auto-Zeff computer program were used and agreements and disagreements between the used methods have been presented and discussed. It has been observed that at higher Em values agreement is quite satisfactory (Dif.<5%) between the adopted methods.

Analogue solution for electrical capacity of membrane covered square cylinders in square array at high concentration.

PubMed

Cole, K S

1975-12-01

Analytical solutions of Laplace equations have given the electrical characteristics of membranes and interiors of spherical, ellipsoidal, and cylindrical cells in suspensions and tissues from impedance measurements, but the underlying assumptions may be invalid above 50% volume concentrations. However, resistance measurements on several nonconducting, close-packing forms in two and three dimensions closely predicted volume concentrations up to 100% by equations derived from Maxwell and Rayleigh. Calculations of membrane capacities of cells in suspensions and tissues from extensions of theory, as developed by Fricke and by Cole, have been useful but of unknown validity at high concentrations. A resistor analogue has been used to solve the finite difference approximation to the Laplace equation for the resistance and capacity of a square array of square cylindrical cells with surface capacity. An 11 x 11 array of resistors, simulating a quarter of the unit structure, was separated into intra- and extra-cellular regions by rows of capacitors corresponding to surface membrane areas from 3 x 3 to 11 x 11 or 7.5% to 100%. The extended Rayleigh equation predicted the cell concentrations and membrane capacities to within a few percent from boundary resistance and capacity measurements at low frequencies. This single example suggests that analytical solutions for other, similar two- and three-dimensional problems may be approximated up to near 100% concentrations and that there may be analytical justifications for such analogue solutions of Laplace equations.

Development of glass fibre reinforced composites using microwave heating technology

NASA Astrophysics Data System (ADS)

Köhler, T.; Vonberg, K.; Gries, T.; Seide, G.

2017-10-01

Fibre reinforced composites are differentiated by the used matrix material (thermoplastic versus duroplastic matrix) and the level of impregnation. Thermoplastic matrix systems get more important due to their suitability for mass production, their good shapeability and their high impact resistance. A challenge in the processing of these materials is the reduction of the melt flow paths of the thermoplastic matrix. The viscosity of molten thermoplastic material is distinctly higher than the viscosity of duroplastic material. An approach to reduce the flow paths of the thermoplastic melt is given by a commingling process. Composites made from commingling hybrid yarns consist of thermoplastic and reinforcing fibres. Fabrics made from these hybrid yarns are heated and consolidated by the use of heat pressing to form so called organic sheets. An innovative heating system is given by microwaves. The advantage of microwave heating is the volumetric heating of the material, where the energy of the electromagnetic radiation is converted into thermal energy inside the material. In this research project microwave active hybrid yarns are produced and examined at the Institute for Textile Technology of RWTH Aachen University (ITA). The industrial research partner Fricke und Mallah Microwave Technology GmbH, Peine, Germany develops an innovative pressing systems based on a microwave heating system. By implementing the designed microwave heating technology into an existing heat pressing process, FRTCs are being manufactured from glass and nanomodified polypropylene fibre woven fabrics. In this paper the composites are investigated for their mechanical and optical properties.

KSC-07pd3398

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- The space shuttle Atlantis STS-122 crew receives instruction on the emergency exit system on Launch Pad 39A. Inside the bunker at the foot of the pad, from left, Mission Specialist Leland Melvin; astronaut Frank De Winne of the European Space Agency, backup for Expedition 16 Flight Engineer Leopold Eyharts; Mission Specialist Stanley Love; and Commander Steve Frick listen intently to their trainer. Seven slidewire baskets are available to carry the crew from the level of the pad's Orbiter Access Arm to a safe landing site below, if needed. Each basket can hold up to three people. A braking system catch net and drag chain slow, and then halt, the baskets as they travel down the wire at approximately 55 miles per hour. The journey takes about half a minute. A bunker is located in the landing zone 1,200 feet west of the pad, with an M-113 armored personnel carrier stationed nearby. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization and a simulated launch countdown before launch. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd3392

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- The space shuttle Atlantis STS-122 crew receives instruction on slidewire basket operation, part of the emergency exit system on the fixed service structure on Launch Pad 39A. Seen here near the catch nets in the landing zone are, from left, Mission Specialists Leopold Eyharts, Hans Schlegel and Rex Walheim; Commander Steve Frick; Mission Specialists Stanley Love and Leland Melvin; and Pilot Alan Poindexter. Seven slidewire baskets are available to carry the crew from the level of the pad's Orbiter Access Arm to this landing site, if needed. Each basket can hold up to three people. A braking system catch net and drag chain slow, and then halt, the baskets as they travel down the wire at approximately 55 miles per hour. The journey takes about half a minute. A bunker is located in the landing zone 1,200 feet west of the pad, with an M-113 armored personnel carrier stationed nearby. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization and a simulated launch countdown before launch. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

KSC-07pd3393

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- The space shuttle Atlantis STS-122 crew receives instruction on slidewire basket operation, part of the emergency exit system on the fixed service structure on Launch Pad 39A. From left, Mission Specialists Stanley Love and Hans Schlegel and Commander Steve Frick gain first-hand experience inside one of the baskets. Seven slidewire baskets are available to carry the crew from the level of the pad's Orbiter Access Arm to this landing site, if needed. Each basket can hold up to three people. A braking system catch net and drag chain slow, and then halt, the baskets as they travel down the wire at approximately 55 miles per hour. The journey takes about half a minute. A bunker is located in the landing zone 1,200 feet west of the pad, with an M-113 armored personnel carrier stationed nearby. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization and a simulated launch countdown before launch. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

STS-110/Atlantic/ISS 8A Pre-Launch On Orbit-Landing-Crew Egress

NASA Technical Reports Server (NTRS)

2002-01-01

The crew of STS-110, which consists of Commander Michael Bloomfield, Pilot Stephen Frick, and Mission Specialists Rex Walheim, Ellen Ochoa, Lee Morin, Jerry Ross, and Steven Smith is introduced at the customary pre-flight meal. The narrator provides background information on the astronauts during suit-up. Each crew member is shown in the White Room before boarding Space Shuttle Atlantis, and some display signs to loved ones. Launch footage includes the following replays: Beach Tracker, VAB, Pad B, Tower 1, DLTR-3, Grandstand, Cocoa Beach DOAMS, Playalinda DOAMS, UCS-23, SLF Convoy, OTV-154, OTV-163, OTV-170 (mislabeled), and OTV-171 (mislabeled). After the launch, NASA administrator Sean O'Keefe gives a speech to the Launch Control Center, with political dignitaries present. While on-orbit, Atlantis docks with the International Space Station (ISS), and Canadarm 2 on the ISS lifts the S0 Truss out of the orbiter's payload bay. The video includes highlights of three extravehicular activities (EVAs). In the first, the S0 Truss is fastened to the Destiny Laboratory Module on the ISS. During the third EVA, Walheim and Smith assist in the checkout of the handcart on the S0 Truss. The Atlantis crew is shown gathered together with the Expedition 4 crew of the ISS, and again by itself after undocking. Replays of the landing include: VAB, Tower 1, Mid-field, Runway South End, Runway North End, Tower 2, Playalinda DOAMS, Cocoa Beach DOAMS, and Pilot Point of View (PPOV). After landing, Commander Bloomfield lets each of his crew members give a short speech.

Competitive pricing within pharmaceutical classes: evidence on "follow-on" drugs in Germany 1993-2008.

PubMed

Mueller, Michael T; Frenzel, Alexander

2015-01-01

Competition from "follow-on" drugs has been a highly controversial issue. Manufacturers launching new molecules in existing drug classes have often been criticized for inflating health systems' expenses, but it has been argued that such drugs increase therapeutic options. Economic theory suggests that follow-on drugs induce price competition. We contribute to this discussion by addressing the topic of pricing at market entry and price development in the German market. We measure determinants of price strategies of follow-on drugs using regression analyses, considering all new molecules launched in the German market from 1993 to 2008. Prices of products are standardized on defined daily dosages controlling for sales volumes based on data from the IMS Health DPM database and for the therapeutic quality of a new product using ratings by Fricke/Klaus as a proxy for innovation. We identify prices correlating with therapeutic value at market entry. While the first two molecules engage in quality competition, price discounts below the market price can be observed from the third entrant on. Price discounts are even more distinct in development races with several drugs entering the market within 2 years and in classes with a low degree of therapeutic differentiation. Prices remain relatively constant over time. This study contributes to assessments of competition in pharmaceutical markets focusing on price strategies of new market entrants. After an initial phase of market building, further follow-on products induce price competition. Largely unchanged prices after 4 years may be interpreted as quality competition and can be attributed to prices in Germany being anchor points for international price referencing.

Accretion and differentiation of carbon in the early Earth.

PubMed

Tingle, T N

1998-05-15

The abundance of C in carbonaceous and ordinary chondrites decreases exponentially with increasing shock pressure as inferred from the petrologic shock classification of Scott et al. [Scott, E.R.D., Keil, K., Stoffler, D., 1992. Shock metamorphism of carbonaceous chondrites. Geochim. Cosmochim. Acta 56, 4281-4293] and Stoffler et al. [Stoffler, D., Keil, K., Scott, E.R.D., 1991. Shock metamorphism of ordinary chondrites. Geochim. Cosmochim. Acta 55, 3845-3867]. This confirms the experimental results of Tyburczy et al. [Tyburczy, J.A., Frisch, B., Ahrens, T.J., 1986. Shock-induced volatile loss from a carbonaceous chondrite: implications for planetary accretion. Earth Planet. Sci. Lett. 80, 201-207] on shock-induced devolatization of the Murchison meteorite showing that carbonaceous chondrites appear to be completely devolatilized at impact velocities greater than 2 km s-1. Both of these results suggest that C incorporation would have been most efficient in the early stages of accretion, and that the primordial C content of the Earth was between 10(24) and 10(25) g C (1-10% efficiency of incorporation). This estimate agrees well with the value of 3-7 x 10(24) g C based on the atmospheric abundance of 36Ar and the chondritic C/36Ar (Marty and Jambon, 1987). Several observations suggest that C likely was incorporated into the Earth's core during accretion. (1) Graphite and carbides are commonly present in iron meteorites, and those iron meteorites with Widmanstatten patterns reflecting the slowest cooling rates (mostly Group I and IIIb) contain the highest C abundances. The C abundance-cooling rate correlation is consistent with dissolution of C into Fe-Ni liquids that segregated to form the cores of the iron meteorite parent bodies. (2) The carbon isotopic composition of graphite in iron meteorites exhibits a uniform value of -5% [Deines, P., Wickman, F.E. 1973. The isotopic composition of 'graphitic' carbon from iron meteorites and some remarks on the troilitic sulfur of iron meteorites. Geochim. Cosmochim. Acta 37, 1295-1319; Deines, P., Wickman, F.E., 1975. A contribution to the stable carbon isotope geochemistry of iron meteorites. Geochim. Cosmochim. Acta 39, 547-557] identical to the mode in the distribution found in diamonds, carbonatites and oceanic basalts [Mattey, D.P., 1987. Carbon isotopes in the mantle. Terra Cognita 7, 31-37]. (3) The room pressure solubility of C in molten iron is 4.3 wt% C. Phase equilibria confirm that the Fe-C eutectic persists to 12 GPa, and thermochemical calculations for the Fe-C-S system by Wood [Wood, B.J., 1993. Carbon in the core. Earth Planet. Sci. Lett. 117, 593-607] predict that C is soluble in Fe liquids at core pressures. The abundance of 36Ar in chondrites decreases exponentially with increasing shock pressure as observed for C. It is well known that noble gases are positively correlated and physically associated with C in meteorites [e.g. Otting, W., Zahringer J., 1967. Total carbon content and primordial rare gases in chondrites. Geochim. Cosmochim. Acta 31, 1949-1960; Reynolds, J.H., Frick, U., Niel, J.M., Phinney, D.L., 1978. Rare-gas-rich separates from carbonaceous chondrites. Geochim. Cosmochim. Acta, 42, 1775-1797]. This suggests a mechanism by which primordial He and other noble gases may have incorporated into the Earth during accretion. The abundance of He in the primordial Earth required to sustain the modern He flux for 4 Ga (assuming a planetary 3 He/4 He; Reynolds et al. [Reynolds, J.H., Frick, U., Niel, J.M., Phinney, D.L., 1978. Rare-gas-rich separates from carbonaceous chondrites. Geochim. Cosmochim. Acta 42, 1775-1797] is calculated to be > or = 10(-8) cm3 g-1. This minimum estimate is consistent with a 1-10% efficiency of noble gas retention during accretion and the observed abundance of He in carbonaceous chondrites (10(-5) to 10(-4) cm3 g-1 excluding spallogenic contributions).

Current status and prospects of radiation processing studies in Taiwan, R. O. C.

NASA Astrophysics Data System (ADS)

Fu, Ying-Kai

The research on radiation processing in past 5 years in Taiwan covers industrial application of radiation-induced polymerization and curing, medical application of radiosterilization of medical supplies, chemicals, and amniotic membrane for wound dressing as well as agricultural application of food irradiation and genogenesis etc. Radiation-induced polymerization applied on wood and bamboo plastic composite of methyl methacrylate, radiation curing on polyurethane and silicon rubber for biomedical material using to separate oxygen from nitrogen and on crosslinking of pp and ps for artificial skin for wound dressing were all success. Radio-sterilization of disposable medical supplies appears for immediate application after the studies of the dose requirement of several radioresistant microorganisms, dose distribution measured by chemical dosimeters of ceric sulfate and Fricke dosimeter as well as quality control system were completed. The radiosterilization study of tetracycline - HCl and few detoxic agents like atropine sulfate and toxogonin has shown the promising results on radiosterilization of chemicals, the radiosterilization of amniotic membrane for wound dressing are also success. Food irradiation on sprouting inhibition of potatoes, garlic etc, on radiodisinfestation of cereal insects, tobacco bettles, soybean insects, and flour beetles, as well as on frog legs and porks have been also discussed. The legislation on radiosterilization of medical supplies and food irradiation of 14 items has been approved by National Health Administration, R.O.C. in July of 1982 and January of 1985 respectively. Even 24 hrs-operation of 1 Mega curie irradiation plant at INER can not satisfy the requirement of radiosterilization of medical supplies. A private commercial irradiation plant is urgently needed in Taiwan other than at INER now.

On the role of distributed helicity in the formation of hurricanes.

NASA Astrophysics Data System (ADS)

Golbraikh, E.; Frick, P.; Stepanov, R.

2016-02-01

The problem of formation (suppression) of hurricanes is one of the most important problems in the physics of the atmosphere and ocean. Till now, no clear picture of the hurricanes formation. Many years ago, in the paper [1] has been proposed a model amplification spiral vortex (such as typhoons), based on the hydrodynamic alpha-effect (HAE). However, in contrast to magnetic alpha-effect, the role turbulent helicity in the behavior of the hydrodynamic systems of hitherto considered passive [2], and consequently, this theory has not has been developed. On the other hand, some experimental data and theoretical estimates indicate that the helicity can influence the process of the formation of large-scale vortices. In the present work, based on the theory of the distributed helicity [3], we show that under certain conditions, helicity ceases to be a passive scalar and strongly influences the transfer of energy from the large scale to small, leading to its accumulation on the large scales, with subsequent transfer into a mean flow. At the same time, we suggest that the influence on a hurricane can be carried out only at the stage of its formation, and we discuss of the behavior some of the parameters that are the predictors of the hurricanes occurrence. References [1] Moiseev, S. S., Sagdeev, R. Z., Tur, A. V., Khomenko, Shukurov, A. M, Physical mechanism of amplification of vortex disturbances in the atmosphere, Soviet Physics Doc., Vol. 28, p.926, 11/1983. [2] H. K. Moffat, Magnetic Field Generation in Electrically Conducting Fluids (Cambridge University Press, Cam- bridge, 1978). [3] R. Stepanov, E. Golbraikh, P. Frick, A. Shestakov, Hindered energy cascade in highly helical isotropic turbulence, arXiv:1508.07236v2

Degradation of Acid Blue 25 in aqueous media using 1700kHz ultrasonic irradiation: ultrasound/Fe(II) and ultrasound/H(2)O(2) combinations.

PubMed

Ghodbane, Houria; Hamdaoui, Oualid

2009-06-01

In this work, the sonolytic degradation of an anthraquinonic dye, C.I. Acid Blue 25 (AB25), in aqueous phase using high frequency ultrasound waves (1700kHz) for an acoustic power of 14W was investigated. The sonochemical efficiency of the reactor was evaluated by potassium iodide dosimeter, Fricke reaction and hydrogen peroxide production yield. The three investigated methods clearly show the production of oxidizing species during sonication and well reflect the sonochemical effects of high frequency ultrasonic irradiation. The effect of operational conditions such as the initial AB25 concentration, solution temperature and pH on the degradation of AB25 was studied. Additionally, the influence of addition of salts on the degradation of dye was examined. The rate of AB25 degradation was dependent on initial dye concentration, pH and temperature. Addition of salts increased the degradation of dye. Experiments conducted using distilled and natural waters demonstrated that the degradation was more efficient in the natural water compared to distilled water. To increase the efficiency of AB25 degradation, experiments combining ultrasound with Fe(II) or H(2)O(2) were conducted. Fe(II) induced the dissociation of ultrasonically produced hydrogen peroxide, leading to additional OH radicals which enhance the degradation of dye. The combination of ultrasound with hydrogen peroxide looks to be a promising option to increase the generation of free radicals. The concentration of hydrogen peroxide plays a crucial role in deciding the extent of enhancement obtained for the combined process. The results of the present work indicate that ultrasound/H(2)O(2) and ultrasound/Fe(II) processes are efficient for the degradation of AB25 in aqueous solutions by high frequency ultrasonic irradiation.

[The presence of callous/unemotional traits among students in different roles of bullying].

PubMed

Nagy, Ildikó; Pataky, Nóra; Szklenárik, Péter; Körmendi, Attila

2012-01-01

The phenomenon of bullying in the schools is more frequent in our country and abroad too. The bullying behaviour is a persistent, intentional harm of others where the balance of power between the participants is uneven.Researches about school bullying has provided many useful information regarding prevention and treatment of bullying but only the few of them takes an interest in the personality traits in bullies which can increase the appearance of the aggressive, bullying behaviour.The callous/unemotional traits get a growing role in the explanation and understanding of aggressive behaviour. In case of the presence of callous/unemotional traits a special emotional (lack of guilt, shallow emotions) and interpersonal style (use of proactive aggression and absence of responsibility) can be observed in children. The purpose of our study was to measure the callous/unemotional traits between the different groups determined by the role they play in the bullying. We assume that the presence of callous/unemotional traits are significantly more typical within the group of Bullies than the other groups. Our sample consisted of 117 elementary school students (6th-8th grade). To examine the roles of bullying we used the Bullying Questionniare. The questionnaire consist 23 items, it was developed to determine the role of students and involvement in the process of bullying. To measure callous/ unemotional traits we used the Inventory of Callous Unemotional Traits (ICU) developed by Frick which measure the factors of callous unemotional traits along 24 items. According to our results the group of Bullies scored significantly higher in all three factors of the Inventory of Callous Unemotional Traits compared to other groups. Treatment of callous/unemotional features may reduce the occurrence of bullying.

Study of a non-diffusing radiochromic gel dosimeter for 3D radiation dose imaging

NASA Astrophysics Data System (ADS)

Marsden, Craig Michael

2000-12-01

This thesis investigates the potential of a new radiation gel dosimeter, based on nitro-blue tetrazolium (NBTZ) suspended in a gelatin mold. Unlike all Fricke based gel dosimeters this dosimeter does not suffer from diffusive loss of image stability. Images are obtained by an optical tomography method. Nitro blue tetrazolium is a common biological indicator that when irradiated in an aqueous medium undergoes reduction to a highly colored formazan, which has an absorbance maximum at 525nm. Tetrazolium is water soluble while the formazan product is insoluble. The formazan product sticks to the gelatin matrix and the dose image is maintained for three months. Methods to maximize the sensitivity of the system were evaluated. It was found that a chemical detergent, Triton X-100, in combination with sodium formate, increased the dosimeter sensitivity significantly. An initial G-value of formazan production for a dosimeter composed of 1mM NBTZ, gelatin, and water was on the order of 0.2. The addition of Triton and formate produced a G-value in excess of 5.0. The effects of NBTZ, triton, formate, and gel concentration were all investigated. All the gels provided linear dose vs. absorbance plots for doses from 0 to >100 Gy. It was determined that gel concentration had minimal if any effect on sensitivity. Sensitivity increased slightly with increasing NBTZ concentration. Triton and formate individually and together provided moderate to large increases in dosimeter sensitivity. The dosimeter described in this work can provide stable 3D radiation dose images for all modalities of radiation therapy equipment. Methods to increase sensitivity are developed and discussed.

KSC-07pd3386

NASA Image and Video Library

2007-11-19

KENNEDY SPACE CENTER, FLA. -- The space shuttle Atlantis STS-122 crew receives instruction on slidewire basket operation, part of the emergency exit system on the fixed service structure on Launch Pad 39A. From left are Mission Specialists Stanley Love; Leopold Eyharts' backup, Frank De Winne; Leland Melvin and Hans Schlegel; Pilot Alan Poindexter; and Commander Steve Frick, with his back to the camera. Schlegel, Eyharts and De Winne are with the European Space Agency. Eyharts will remain on the International Space Station as a flight engineer for Expedition 16 following the STS-122 mission. Seven slidewire baskets are available to carry the crew from the level of the pad's Orbiter Access Arm to a safe landing site below, if needed. Each basket can hold up to three people. A braking system catch net and drag chain slow, and then halt, the baskets as they travel down the wire at approximately 55 miles per hour. The journey takes about half a minute. A bunker is located in the landing zone 1,200 feet west of the pad, with an M-113 armored personnel carrier stationed nearby. The STS-122 crew is at NASA's Kennedy Space Center to take part in terminal countdown demonstration test, or TCDT, activities, a standard part of launch preparations. The TCDT provides astronauts and ground crews with equipment familiarization and a simulated launch countdown before launch. On mission STS-122, Atlantis will deliver the European Space Agency's Columbus module to the International Space Station. Columbus is a multifunctional, pressurized laboratory that will be permanently attached to U.S. Node 2, called Harmony, and will expand the research facilities aboard the station. Launch is targeted for Dec. 6. Photo credit: NASA/Kim Shiflett

Nutritional Modulation of Age-Related Macular Degeneration

PubMed Central

Weikel, Karen A; Taylor, Allen

2012-01-01

Age-related macular degeneration (AMD) is the leading cause of blindness in the elderly worldwide. It affects 30–50 million individuals and clinical hallmarks of AMD are observed in at least one third of persons over the age of 75 in industrialized countries (Gehrs et al., 2006). Costs associated with AMD are in excess of $340 billion US (American-Health-Assistance-Foundation, 2012). The majority of AMD patients in the United States are not eligible for clinical treatments (Biarnes et al., 2011; Klein et al., 2011). Preventive interventions through dietary modulation are attractive strategies because many studies suggest a benefit of micro and macronutrients with respect to AMD, as well as other age-related debilities, and with few, if any, adverse effects (Chiu, 2011). Preservation of vision would enhance quality of life for millions of elderly people, and alleviate the personal and public health financial burden of AMD (Frick et al., 2007; Wood et al., 2011). Observational studies indicate that maintaining adequate levels of omega-3 fatty acids (i.e. with 2 servings/wk of fish) or a low glycemic index diet may be particularly beneficial for early AMD and that higher levels of carotenoids may be protective, most probably, against neovascular AMD. Intervention trials are needed to better understand the full effect of these nutrients and/or combinations of nutrients on retinal health. Analyses that describe effects of a nutrient on onset and/or progress of AMD are valuable because they indicate the value of a nutrient to arrest AMD at the early stages. This comprehensive summary provides essential information about the value of nutrients with regard to diminishing risk for onset or progress of AMD and can serve as a guide until data from ongoing intervention trials are available. PMID:22503690

Inclusion-Based Effective Medium Models for the Permeability of a 3D Fractured Rock Mass

NASA Astrophysics Data System (ADS)

Ebigbo, A.; Lang, P. S.; Paluszny, A.; Zimmerman, R. W.

2015-12-01

Following the work of Saevik et al. (Transp. Porous Media, 2013; Geophys. Prosp., 2014), we investigate the ability of classical inclusion-based effective medium theories to predict the macroscopic permeability of a fractured rock mass. The fractures are assumed to be thin, oblate spheroids, and are treated as porous media in their own right, with permeability kf, and are embedded in a homogeneous matrix having permeability km. At very low fracture densities, the effective permeability is given exactly by a well-known expression that goes back at least as far as Fricke (Phys. Rev., 1924). For non-trivial fracture densities, an effective medium approximation must be employed. We have investigated several such approximations: Maxwell's method, the differential method, and the symmetric and asymmetric versions of the self-consistent approximation. The predictions of the various approximate models are tested against the results of explicit numerical simulations, averaged over numerous statistical realizations for each set of parameters. Each of the various effective medium approximations satisfies the Hashin-Shtrikman (H-S) bounds. Unfortunately, these bounds are much too far apart to provide quantitatively useful estimates of keff. For the case of zero matrix permeability, the well-known approximation of Snow, which is based on network considerations rather than a continuum approach, is shown to essentially coincide with the upper H-S bound, thereby proving that the commonly made assumption that Snow's equation is an "upper bound" is indeed correct. This problem is actually characterized by two small parameters, the aspect ratio of the spheroidal fractures, α, and the permeability ratio, κ = km/kf. Two different regimes can be identified, corresponding to α < κ and κ < α, and expressions for each of the effective medium approximations are developed in both regimes. In both regimes, the symmetric version of the self-consistent approximation is the most accurate.

Stellar Evolution with Rotation: Mixing Processes in AGB Stars

NASA Astrophysics Data System (ADS)

Driebe, T.; Blöcker, T.

We included diffusive angular momentum transport and rotationally induced mixing processes in our stellar evolution code and studied the influence of rotation on the evolution of intermediate mass stars (M*=2dots6 Msolar) towards and along the asymptotic giant branch (AGB). The calculations start in the fully convective pre-main sequence phase and the initial angular momentu m was adjusted such that on the zero-age main sequence vrot=200 km/ s is achieved. The diffusion coefficients for the five rotational instabilities considered (dynamical shear, secular shear, Eddington-Sweet (ES) circulation, Solberg-Høiland-instability and Goldreich-Schubert-Fricke (GSF) instability) were adopted from Heger et al. (2000, ApJ 528, 368). Mixing efficiency and sensitivity of these processes against molecular weight gradients have been determined by calibration of the main sequence width. In this study we focus on the abundance evolution of carbon. On the one hand, the surface abundance ratios of 12C/13C a nd 12C/16O at the base of the AGB were found to be ≈ 7dots 10 and ≈ 0.1, resp., being a factor of two lower than in non-rotating models. This results from the slow but continuously operating rotationally induced mixing due to the ES-circulation and the GSF-instability during the long main sequence phase. On the other hand, 13C serves as neutron source for interior s-process nucleosynthesis in AGB stars vi a 13C(α,n)16O. Herwig et al. (1997, A&A 324, L81) found that a 13C pocket is forme d in the intershell region of 3 Msolar AGB star if diffusive overshoot is considered. Our calculations show, that mixing processes due to rotation open an alternative channel for the formation of a 13C pocket as found by Langer et al. (1999, A&A 346, L37). Again, ES-circulation and GSF-instability are the predominant rotational mixing processes.

Child maltreatment, callous-unemotional traits, and defensive responding in high-risk children: An investigation of emotion-modulated startle response.

PubMed

Dackis, Melissa N; Rogosch, Fred A; Cicchetti, Dante

2015-11-01

Child maltreatment is associated with disruptions in physiological arousal, emotion regulation, and defensive responses to cues of threat and distress, as well as increased risk for callous unemotional (CU) traits and externalizing behavior. Developmental models of CU traits have focused on biological and genetic risk factors that contribute to hypoarousal and antisocial behavior, but have focused less on environmental influences (Blair, 2004; Daversa, 2010; Hare, Frazell, & Cox, 1978; Krueger, 2000; Shirtcliff et al., 2009; Viding, Fontaine, & McCrory, 2012). The aim of the present investigation was to measure the independent and combined effects of child maltreatment and high CU traits on emotion-modulated startle response in children. Participants consisted of 132 low-income maltreated (n = 60) and nonmaltreated (n = 72) children between 8 and 12 years old who attended a summer camp program. Acoustic startle response (ASR) was elicited in response to a 110-dB 50-ms probe while children viewed a slideshow of pleasant, neutral, and unpleasant IAPS images. Maltreatment status was assessed through examination of Department of Human Services records. CU traits were measured using counselor reports from the Inventory of Callous and Unemotional Traits (Frick, 2004), and conduct problems were measured using counselor and child self-report. We found no significant differences in emotion-modulated startle in the overall sample. However, significant differences in ASR by maltreatment status, maltreatment subtype, and level of CU traits were apparent. Results indicated differential physiological responses for maltreated and nonmaltreated children based on CU traits, including a pathway of hypoarousal for nonmaltreated/high CU children that differed markedly from a more normative physiological trajectory for maltreated/high CU children. Further, we found heightened ASR for emotionally and physically neglected children with high CU and elevated antisocial behavior in these children. Results provide further support for differential trajectories by which experience and biology may influence the development of antisocial behavior in youth and highlight potential avenues for intervention.

Child Maltreatment, Callous-Unemotional Traits, and Defensive Responding In High-Risk Children: An Investigation of Emotion-Modulated Startle Response

PubMed Central

Dackis, Melissa N.; Rogosch, Fred A.; Cicchetti, Dante

2015-01-01

Child maltreatment is associated with disruptions in physiological arousal, emotion regulation, and defensive responses to cues of threat and distress, as well as increased risk for callous unemotional (CU) traits and externalizing behavior. Developmental models of callous unemotional (CU) traits have focused on biological and genetic risk factors that contribute to hypoarousal and antisocial behavior, but have focused less on environmental influences (Blair, 2004; Daversa, 2010; Hare, Frazell, & Cox, 1978; Krueger, 2000; Shirtcliff et al., 2009; Viding, Fontaine, & McCrory, 2012). The aim of the present investigation was to measure the independent and combined effects of child maltreatment and high CU trait on emotion-modulated startle (EMS) response in children. Participants consisted of 132 low-income maltreated (n = 60) and nonmaltreated (n = 72) children between 8–12 years old who attended a summer camp program. Acoustic startle response (ASR) was elicited in response to a 110-dB 50-ms probe while children viewed a slideshow of pleasant, neutral, and unpleasant IAPS images. Maltreatment status was assessed through examination of Department of Human Services records. CU traits were measured using counselor reports from the Inventory of Callous and Unemotional Traits (ICU; Frick, 2004), and conduct problems were measured using counselor and child self-report. We found no significant differences in emotion-modulated startle in the overall sample. However, significant differences in ASR by maltreatment status, maltreatment subtype, and level of CU traits were apparent. Results indicated differential physiological responses for maltreated and nonmaltreated children based on CU traits, including a pathway of hypoarousal for nonmaltreated/high CU children that differed markedly from a more normative physiological trajectory for maltreated/high CU children. Further, we found heightened ASR for emotionally and physically neglected children with high CU and elevated antisocial behavior in these children. Results provide further support for differential trajectories by which experience and biology may influence the development of antisocial behavior in youth and highlight potential avenues for intervention. PMID:26535942

Oxygen enhances phosphine toxicity for postharvest pest control.

PubMed

Liu, Yong-Biao

2011-10-01

Phosphine fumigations under superatmospheric oxygen levels (oxygenated phosphine fumigations) were significantly more effective than the fumigations under the normal 20.9% atmospheric oxygen level against western flower thrips [Frankliniella occidentalis (Pergande)] adults and larvae, leafminer Liriomyza langei Frick pupae, grape mealybug [Pseudococcus maritimus (Ehrhorn)] eggs, and Indianmeal moth [Plodia interpunctella (Hübner)] eggs and pupae. In 5-h fumigations with 1,000 ppm phosphine at 5 degrees C, mortalities of western flower thrips increased significantly from 79.5 to 97.7% when oxygen was increased from 20.9 to 40% and reached 99.3% under 80% O2. Survivorships of leafminer pupae decreased significantly from 71.2% under 20.9% O2 to 16.2% under 40% O2 and reached 1.1% under 80% O2 in 24-h fumigations with 500 ppm phosphine at 5 degrees C. Complete control of leafminer pupae was achieved in 24-h fumigations with 1,000 ppm phosphine at 5 degrees C under 60% O2 or higher. Survivorships of grape mealybug eggs also decreased significantly in 48-h fumigations with 1,000 ppm phosphine at 2 degrees C under 60% O2 compared with the fumigations under 20.9% O2. Indian meal moth egg survivorships decreased significantly from 17.4 to 0.5% in responses to an oxygen level increase from 20.9 to 40% in 48-h fumigations with 1,000 ppm phosphine at 10 degrees C and reached 0.2% in fumigations under 80% O2. When the oxygen level was reduced from 20.9 to 15 and 10% in fumigations, survivorships of Indianmeal moth eggs increased significantly from 17.4 to 32.9 and 39.9%, respectively. Increased O2 levels also resulted in significantly lower survival rates of Indianmeal moth pupae in response to 24-h fumigations with 500 and 1,000 ppm phosphine at 10 degrees C and a complete control was achieved in the 1,000 ppm phosphine fumigations under 60% O2. Oxygenated phosphine fumigations have marked potential to improve insecticidal efficacy. Advantages and limitations of oxygenated phosphine fumigation are discussed.

Semiconductor-based, large-area, flexible, electronic devices

DOEpatents

Goyal, Amit [Knoxville, TN

2011-03-15

Novel articles and methods to fabricate the same resulting in flexible, large-area, triaxially textured, single-crystal or single-crystal-like, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

Semiconductor-based, large-area, flexible, electronic devices on {110}<100> oriented substrates

DOEpatents

Goyal, Amit

2014-08-05

Novel articles and methods to fabricate the same resulting in flexible, oriented, semiconductor-based, electronic devices on {110}<100> textured substrates are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

[100] or [110] aligned, semiconductor-based, large-area, flexible, electronic devices

DOEpatents

Goyal, Amit

2015-03-24

Novel articles and methods to fabricate the same resulting in flexible, large-area, [100] or [110] textured, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

{100}<100> or 45.degree.-rotated {100}<100>, semiconductor-based, large-area, flexible, electronic devices

DOEpatents

Goyal, Amit [Knoxville, TN

2012-05-15

Novel articles and methods to fabricate the same resulting in flexible, {100}<100> or 45.degree.-rotated {100}<100> oriented, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

76 FR 45860 - In the Matter of Certain Electronic Devices, Including Wireless Communication Devices, Portable...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-01

..., Including Wireless Communication Devices, Portable Music and Data Processing Devices, and Tablet Computers... electronic devices, including wireless communication devices, portable music and data processing devices, and... electronic devices, including wireless communication devices, portable music and data processing devices, and...

Wireless device monitoring methods, wireless device monitoring systems, and articles of manufacture

DOEpatents

McCown, Steven H [Rigby, ID; Derr, Kurt W [Idaho Falls, ID; Rohde, Kenneth W [Idaho Falls, ID

2012-05-08

Wireless device monitoring methods, wireless device monitoring systems, and articles of manufacture are described. According to one embodiment, a wireless device monitoring method includes accessing device configuration information of a wireless device present at a secure area, wherein the device configuration information comprises information regarding a configuration of the wireless device, accessing stored information corresponding to the wireless device, wherein the stored information comprises information regarding the configuration of the wireless device, comparing the device configuration information with the stored information, and indicating the wireless device as one of authorized and unauthorized for presence at the secure area using the comparing.

16 CFR § 1507.9 - Toy smoke devices and flitter devices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Toy smoke devices and flitter devices. Â... SUBSTANCES ACT REGULATIONS FIREWORKS DEVICES § 1507.9 Toy smoke devices and flitter devices. (a) Toy smoke... fuse and firstfire upon ignition) during normal operation. (b) Toy smoke devices and flitter devices...

16 CFR 1507.9 - Toy smoke devices and flitter devices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Toy smoke devices and flitter devices. 1507... SUBSTANCES ACT REGULATIONS FIREWORKS DEVICES § 1507.9 Toy smoke devices and flitter devices. (a) Toy smoke... fuse and firstfire upon ignition) during normal operation. (b) Toy smoke devices and flitter devices...

16 CFR 1507.9 - Toy smoke devices and flitter devices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Toy smoke devices and flitter devices. 1507... SUBSTANCES ACT REGULATIONS FIREWORKS DEVICES § 1507.9 Toy smoke devices and flitter devices. (a) Toy smoke... fuse and firstfire upon ignition) during normal operation. (b) Toy smoke devices and flitter devices...

16 CFR 1507.9 - Toy smoke devices and flitter devices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Toy smoke devices and flitter devices. 1507... SUBSTANCES ACT REGULATIONS FIREWORKS DEVICES § 1507.9 Toy smoke devices and flitter devices. (a) Toy smoke... fuse and firstfire upon ignition) during normal operation. (b) Toy smoke devices and flitter devices...

77 FR 58576 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-21

... Devices, Portable Music and Data Processing Devices, Computers, and Components Thereof; Institution of... communication devices, portable music and data processing devices, computers, and components thereof by reason... certain wireless communication devices, portable music and data processing devices, computers, and...

78 FR 34669 - Certain Electronic Devices, Including Wireless Communication Devices, Portable Music and Data...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-10

..., Including Wireless Communication Devices, Portable Music and Data Processing Devices, and Tablet Computers... importing wireless communication devices, portable music and data processing devices, and tablet computers... certain electronic devices, including wireless communication devices, portable music and data processing...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 882.1560 - Skin potential measurement device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Skin potential measurement device. 882.1560... (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Diagnostic Devices § 882.1560 Skin potential measurement device. (a) Identification. A skin potential measurement device is a general diagnostic device...

21 CFR 872.2060 - Jaw tracking device.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2060 Jaw tracking device. (a) Jaw tracking device... Controls Guidance Document: Dental Sonography and Jaw Tracking Devices.” [68 FR 67367, Dec. 2, 2003] ...

21 CFR 872.2050 - Dental sonography device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental sonography device. 872.2050 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2050 Dental sonography device. (a) Dental sonography device for monitoring—(1) Identification. A dental sonography device for monitoring is an...

21 CFR 872.2050 - Dental sonography device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Dental sonography device. 872.2050 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2050 Dental sonography device. (a) Dental sonography device for monitoring—(1) Identification. A dental sonography device for monitoring is an...

21 CFR 872.2050 - Dental sonography device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Dental sonography device. 872.2050 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2050 Dental sonography device. (a) Dental sonography device for monitoring—(1) Identification. A dental sonography device for monitoring is an...

21 CFR 872.2050 - Dental sonography device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Dental sonography device. 872.2050 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2050 Dental sonography device. (a) Dental sonography device for monitoring—(1) Identification. A dental sonography device for monitoring is an...

21 CFR 872.2050 - Dental sonography device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Dental sonography device. 872.2050 Section 872...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2050 Dental sonography device. (a) Dental sonography device for monitoring—(1) Identification. A dental sonography device for monitoring is an...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

21 CFR 872.6010 - Abrasive device and accessories.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6010 Abrasive device and accessories... crowns. The device is attached to a shank that is held by a handpiece. The device includes the abrasive...

Processes for multi-layer devices utilizing layer transfer

DOEpatents

Nielson, Gregory N; Sanchez, Carlos Anthony; Tauke-Pedretti, Anna; Kim, Bongsang; Cederberg, Jeffrey; Okandan, Murat; Cruz-Campa, Jose Luis; Resnick, Paul J

2015-02-03

A method includes forming a release layer over a donor substrate. A plurality of devices made of a first semiconductor material are formed over the release layer. A first dielectric layer is formed over the plurality of devices such that all exposed surfaces of the plurality of devices are covered by the first dielectric layer. The plurality of devices are chemically attached to a receiving device made of a second semiconductor material different than the first semiconductor material, the receiving device having a receiving substrate attached to a surface of the receiving device opposite the plurality of devices. The release layer is etched to release the donor substrate from the plurality of devices. A second dielectric layer is applied over the plurality of devices and the receiving device to mechanically attach the plurality of devices to the receiving device.

21 CFR 872.1740 - Caries detection device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Caries detection device. 872.1740 Section 872.1740...) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1740 Caries detection device. (a) Identification. The caries detection device is a device intended to show the existence of decay in a patient's tooth...

21 CFR 892.2010 - Medical image storage device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Medical image storage device. 892.2010 Section 892...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2010 Medical image storage device. (a) Identification. A medical image storage device is a device that provides electronic storage and retrieval...

21 CFR 892.2010 - Medical image storage device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Medical image storage device. 892.2010 Section 892...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2010 Medical image storage device. (a) Identification. A medical image storage device is a device that provides electronic storage and retrieval...

21 CFR 892.2010 - Medical image storage device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Medical image storage device. 892.2010 Section 892...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2010 Medical image storage device. (a) Identification. A medical image storage device is a device that provides electronic storage and retrieval...

21 CFR 892.2010 - Medical image storage device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Medical image storage device. 892.2010 Section 892...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2010 Medical image storage device. (a) Identification. A medical image storage device is a device that provides electronic storage and retrieval...

21 CFR 886.1450 - Corneal radius measuring device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Corneal radius measuring device. 886.1450 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Diagnostic Devices § 886.1450 Corneal radius measuring device. (a) Identification. A corneal radius measuring device is an AC-powered device intended to measure...

21 CFR 886.4360 - Ocular surgery irrigation device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Ocular surgery irrigation device. 886.4360 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4360 Ocular surgery irrigation device. (a) Identification. An ocular surgery irrigation device is a device intended to be suspended over the...

21 CFR 886.4360 - Ocular surgery irrigation device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Ocular surgery irrigation device. 886.4360 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4360 Ocular surgery irrigation device. (a) Identification. An ocular surgery irrigation device is a device intended to be suspended over the...

21 CFR 886.4360 - Ocular surgery irrigation device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Ocular surgery irrigation device. 886.4360 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4360 Ocular surgery irrigation device. (a) Identification. An ocular surgery irrigation device is a device intended to be suspended over the...

21 CFR 886.4360 - Ocular surgery irrigation device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Ocular surgery irrigation device. 886.4360 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4360 Ocular surgery irrigation device. (a) Identification. An ocular surgery irrigation device is a device intended to be suspended over the...

21 CFR 886.4360 - Ocular surgery irrigation device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ocular surgery irrigation device. 886.4360 Section... (CONTINUED) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4360 Ocular surgery irrigation device. (a) Identification. An ocular surgery irrigation device is a device intended to be suspended over the...

21 CFR 892.2010 - Medical image storage device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Medical image storage device. 892.2010 Section 892...) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2010 Medical image storage device. (a) Identification. A medical image storage device is a device that provides electronic storage and retrieval...

21 CFR 872.1820 - Dental x-ray exposure alignment device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Dental x-ray exposure alignment device. 872.1820... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1820 Dental x-ray exposure alignment device. (a) Identification. A dental x-ray exposure alignment device is a device intended to position x...

21 CFR 872.1840 - Dental x-ray position indicating device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Dental x-ray position indicating device. 872.1840... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1840 Dental x-ray position indicating device. (a) Identification. A dental x-ray position indicating device is a device, such as a collimator...

21 CFR 872.1840 - Dental x-ray position indicating device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Dental x-ray position indicating device. 872.1840... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1840 Dental x-ray position indicating device. (a) Identification. A dental x-ray position indicating device is a device, such as a collimator...

21 CFR 872.1820 - Dental x-ray exposure alignment device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Dental x-ray exposure alignment device. 872.1820... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1820 Dental x-ray exposure alignment device. (a) Identification. A dental x-ray exposure alignment device is a device intended to position x...

21 CFR 872.1820 - Dental x-ray exposure alignment device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental x-ray exposure alignment device. 872.1820... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1820 Dental x-ray exposure alignment device. (a) Identification. A dental x-ray exposure alignment device is a device intended to position x...

21 CFR 872.1820 - Dental x-ray exposure alignment device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Dental x-ray exposure alignment device. 872.1820... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1820 Dental x-ray exposure alignment device. (a) Identification. A dental x-ray exposure alignment device is a device intended to position x...

21 CFR 872.1840 - Dental x-ray position indicating device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Dental x-ray position indicating device. 872.1840... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1840 Dental x-ray position indicating device. (a) Identification. A dental x-ray position indicating device is a device, such as a collimator...

21 CFR 872.1840 - Dental x-ray position indicating device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Dental x-ray position indicating device. 872.1840... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1840 Dental x-ray position indicating device. (a) Identification. A dental x-ray position indicating device is a device, such as a collimator...

21 CFR 872.1820 - Dental x-ray exposure alignment device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Dental x-ray exposure alignment device. 872.1820... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1820 Dental x-ray exposure alignment device. (a) Identification. A dental x-ray exposure alignment device is a device intended to position x...

21 CFR 872.1840 - Dental x-ray position indicating device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dental x-ray position indicating device. 872.1840... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1840 Dental x-ray position indicating device. (a) Identification. A dental x-ray position indicating device is a device, such as a collimator...

21 CFR 892.2040 - Medical image hardcopy device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Medical image hardcopy device. 892.2040 Section... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2040 Medical image hardcopy device. (a) Identification. A medical image hardcopy device is a device that produces a visible printed record of a medical...

21 CFR 892.2040 - Medical image hardcopy device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Medical image hardcopy device. 892.2040 Section... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2040 Medical image hardcopy device. (a) Identification. A medical image hardcopy device is a device that produces a visible printed record of a medical...

21 CFR 892.2040 - Medical image hardcopy device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Medical image hardcopy device. 892.2040 Section... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2040 Medical image hardcopy device. (a) Identification. A medical image hardcopy device is a device that produces a visible printed record of a medical...

21 CFR 892.2040 - Medical image hardcopy device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Medical image hardcopy device. 892.2040 Section... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2040 Medical image hardcopy device. (a) Identification. A medical image hardcopy device is a device that produces a visible printed record of a medical...

21 CFR 892.1610 - Diagnostic x-ray beam-limiting device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Diagnostic x-ray beam-limiting device. 892.1610... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1610 Diagnostic x-ray beam-limiting device. (a) Identification. A diagnostic x-ray beam-limiting device is a device such as a collimator, a...

21 CFR 892.1610 - Diagnostic x-ray beam-limiting device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Diagnostic x-ray beam-limiting device. 892.1610... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1610 Diagnostic x-ray beam-limiting device. (a) Identification. A diagnostic x-ray beam-limiting device is a device such as a collimator, a...

21 CFR 892.1610 - Diagnostic x-ray beam-limiting device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Diagnostic x-ray beam-limiting device. 892.1610... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1610 Diagnostic x-ray beam-limiting device. (a) Identification. A diagnostic x-ray beam-limiting device is a device such as a collimator, a...

21 CFR 892.1610 - Diagnostic x-ray beam-limiting device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Diagnostic x-ray beam-limiting device. 892.1610... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1610 Diagnostic x-ray beam-limiting device. (a) Identification. A diagnostic x-ray beam-limiting device is a device such as a collimator, a...

21 CFR 892.1610 - Diagnostic x-ray beam-limiting device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Diagnostic x-ray beam-limiting device. 892.1610... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1610 Diagnostic x-ray beam-limiting device. (a) Identification. A diagnostic x-ray beam-limiting device is a device such as a collimator, a...

21 CFR 864.9195 - Blood mixing devices and blood weighing devices.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Blood mixing devices and blood weighing devices... Manufacture Blood and Blood Products § 864.9195 Blood mixing devices and blood weighing devices. (a) Identification. A blood mixing device is a device intended for medical purposes that is used to mix blood or...

21 CFR 864.9195 - Blood mixing devices and blood weighing devices.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Blood mixing devices and blood weighing devices... Manufacture Blood and Blood Products § 864.9195 Blood mixing devices and blood weighing devices. (a) Identification. A blood mixing device is a device intended for medical purposes that is used to mix blood or...

21 CFR 864.9195 - Blood mixing devices and blood weighing devices.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Blood mixing devices and blood weighing devices... Manufacture Blood and Blood Products § 864.9195 Blood mixing devices and blood weighing devices. (a) Identification. A blood mixing device is a device intended for medical purposes that is used to mix blood or...

21 CFR 864.9195 - Blood mixing devices and blood weighing devices.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Blood mixing devices and blood weighing devices... Manufacture Blood and Blood Products § 864.9195 Blood mixing devices and blood weighing devices. (a) Identification. A blood mixing device is a device intended for medical purposes that is used to mix blood or...

21 CFR 864.9195 - Blood mixing devices and blood weighing devices.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Blood mixing devices and blood weighing devices... Manufacture Blood and Blood Products § 864.9195 Blood mixing devices and blood weighing devices. (a) Identification. A blood mixing device is a device intended for medical purposes that is used to mix blood or...

78 FR 16865 - Certain Electronic Devices, Including Wireless Communication Devices, Portable Music and Data...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-19

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-794] Certain Electronic Devices, Including Wireless Communication Devices, Portable Music and Data Processing Devices, and Tablet Computers... certain electronic devices, including wireless communication devices, portable music and data processing...

Continuation of copper and levonorgestrel intrauterine devices: a retrospective cohort study.

PubMed

Phillips, Sharon J; Hofler, Lisa G; Modest, Anna M; Harvey, Lara F B; Wu, Lily H; Hacker, Michele R

2017-07-01

Studies conflict on whether the duration of use of the copper intrauterine device is longer than that of the levonorgestrel intrauterine device, and whether women who continue using intrauterine devices differ from those who discontinue. We sought to assess continuation rates and performance of levonorgestrel intrauterine devices compared with copper intrauterine devices over a 5-year period. We performed a retrospective cohort study of 1164 individuals who underwent intrauterine device placement at an urban academic medical center. The analysis focused on a comparison of continuation rates between those using levonorgestrel intrauterine device and copper intrauterine device, factors associated with discontinuation, and intrauterine device performance. We assessed the differences in continuation at discrete time points, pregnancy, and expulsion rates using χ 2 tests and calculated hazard ratios using a multivariable Cox model. Of 1164 women who underwent contraceptive intrauterine device insertion, 956 had follow-up data available. At 2 years, 64.9% of levonorgestrel intrauterine device users continued their device, compared with 57.7% of copper intrauterine device users (P = .11). At 4 years, continuation rates were 45.1% for levonorgestrel intrauterine device and 32.6% for copper intrauterine device (P < .01), and at 5 years continuation rates were 28.1% for levonorgestrel intrauterine device and 23.8% for copper intrauterine device (P = .33). Black race, primiparity, and age were positively associated with discontinuation; education was not. The hazard ratio for discontinuation of levonorgestrel intrauterine device compared with copper intrauterine device >4 years was 0.71 (95% confidence interval, 0.55-0.93) and >5 years was 0.82 (95% confidence interval, 0.64-1.05) after adjusting for race, age, parity, and education. Copper intrauterine device users were more likely to experience expulsion (10.2% copper intrauterine device vs 4.9% levonorgestrel intrauterine device, P < .01) over the study period and to become pregnant in the first year of use (1.6% copper intrauterine device vs 0.1% levonorgestrel intrauterine device, P < .01). We found a difference in continuation rates between levonorgestrel and copper intrauterine device users at 4 years but not at 5 years. Copper intrauterine device users were more likely to experience expulsion and pregnancy. Copyright © 2017 Elsevier Inc. All rights reserved.

Continuation of copper and levonorgestrel intrauterine devices: a retrospective cohort study

PubMed Central

Phillips, Sharon J.; Hofler, Lisa G.; Modest, Anna M.; Harvey, Lara F. B.; Wu, Lily H.; Hacker, Michele R.

2018-01-01

Background Studies conflict on whether the duration of use of the copper intrauterine device is longer than that of the levonorgestrel intra-uterine device, and whether women who continue using intrauterine devices differ from those who discontinue. Objective We sought to assess continuation rates and performance of levonorgestrel intrauterine devices compared with copper intrauterine devices over a 5-year period. Study Design We performed a retrospective cohort study of 1164 individuals who underwent intrauterine device placement at an urban academic medical center. The analysis focused on a comparison of continuation rates between those using levonorgestrel intrauterine device and copper intrauterine device, factors associated with discontinuation, and intrauterine device performance. We assessed the differences in continuation at discrete time points, pregnancy, and expulsion rates using χ2 tests and calculated hazard ratios using a multivariable Cox model. Results Of 1164 women who underwent contraceptive intrauterine device insertion, 956 had follow-up data available. At 2 years, 64.9% of levonorgestrel intrauterine device users continued their device, compared with 57.7% of copper intrauterine device users (P = .11). At 4 years, continuation rates were 45.1% for levonorgestrel intrauterine device and 32.6% for copper intrauterine device (P < .01), and at 5 years continuation rates were 28.1% for levonorgestrel intrauterine device and 23.8% for copper intrauterine device (P = .33). Black race, primiparity, and age were positively associated with discontinuation; education was not. The hazard ratio for discontinuation of levonorgestrel intrauterine device compared with copper intrauterine device >4 years was 0.71 (95% confidence interval, 0.55–0.93) and >5 years was 0.82 (95% confidence interval, 0.64–1.05) after adjusting for race, age, parity, and education. Copper intrauterine device users were more likely to experience expulsion (10.2% copper intrauterine device vs 4.9% levonorgestrel intrauterine device, P < .01) over the study period and to become pregnant in the first year of use (1.6% copper intrauterine device vs 0.1% levonorgestrel intrauterine device, P < .01). Conclusion We found a difference in continuation rates between levonorgestrel and copper intrauterine device users at 4 years but not at 5 years. Copper intrauterine device users were more likely to experience expulsion and pregnancy. PMID:28315664

Evaluation of tissue interactions with mechanical elements of a transscleral drug delivery device.

PubMed

Cohen, Sarah J; Chan, Robison V Paul; Keegan, Mark; Andreoli, Christopher M; Borenstein, Jeffrey T; Miller, Joan W; Gragoudas, Evangelos S

2012-03-12

The goal of this work was to evaluate tissue-device interactions due to implantation of a mechanically operated drug delivery system onto the posterior sclera. Two test devices were designed and fabricated to model elements of the drug delivery device-one containing a free-spinning ball bearing and the other encasing two articulating gears. Openings in the base of test devices modeled ports for drug passage from device to sclera. Porous poly(tetrafluoroethylene) (PTFE) membranes were attached to half of the gear devices to minimize tissue ingrowth through these ports. Test devices were sutured onto rabbit eyes for 10 weeks. Tissue-device interactions were evaluated histologically and mechanically after removal to determine effects on device function and changes in surrounding tissue. Test devices were generally well-tolerated during residence in the animal. All devices encouraged fibrous tissue formation between the sclera and the device, fibrous tissue encapsulation and invasion around the device, and inflammation of the conjunctiva. Gear devices encouraged significantly greater inflammation in all cases and a larger rate of tissue ingrowth. PTFE membranes prevented tissue invasion through the covered drug ports, though tissue migrated in through other smaller openings. The torque required to turn the mechanical elements increased over 1000 times for gear devices, but only on the order of 100 times for membrane-covered gear devices and less than 100 times for ball bearing devices. Maintaining a lower device profile, minimizing microscale motion on the eye surface and covering drug ports with a porous membrane may minimize inflammation, decreasing the risk of damage to surrounding tissues and minimizing disruption of device operation.

77 FR 60720 - Certain Electronic Devices, Including Wireless Commmunication Devices, Portable Music and Data...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-04

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-794] Certain Electronic Devices, Including Wireless Commmunication Devices, Portable Music and Data Processing Devices, and Tablet Computers... communication devices, portable music and data processing devices, and tablet computers, imported by Apple Inc...

21 CFR 892.2020 - Medical image communications device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Medical image communications device. 892.2020... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2020 Medical image communications device. (a) Identification. A medical image communications device provides electronic transfer of medical...

21 CFR 892.2020 - Medical image communications device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Medical image communications device. 892.2020... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2020 Medical image communications device. (a) Identification. A medical image communications device provides electronic transfer of medical...

21 CFR 892.2020 - Medical image communications device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Medical image communications device. 892.2020... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2020 Medical image communications device. (a) Identification. A medical image communications device provides electronic transfer of medical...

21 CFR 892.2020 - Medical image communications device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Medical image communications device. 892.2020... (CONTINUED) MEDICAL DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.2020 Medical image communications device. (a) Identification. A medical image communications device provides electronic transfer of medical...

Release strategies for making transferable semiconductor structures, devices and device components

DOEpatents

Rogers, John A; Nuzzo, Ralph G; Meitl, Matthew; Ko, Heung Cho; Yoon, Jongseung; Menard, Etienne; Baca, Alfred J

2014-11-25

Provided are methods for making a device or device component by providing a multilayer structure having a plurality of functional layers and a plurality of release layers and releasing the functional layers from the multilayer structure by separating one or more of the release layers to generate a plurality of transferable structures. The transferable structures are printed onto a device substrate or device component supported by a device substrate. The methods and systems provide means for making high-quality and low-cost photovoltaic devices, transferable semiconductor structures, (opto-)electronic devices and device components.

Release strategies for making transferable semiconductor structures, devices and device components

DOEpatents

Rogers, John A [Champaign, IL; Nuzzo, Ralph G [Champaign, IL; Meitl, Matthew [Raleigh, NC; Ko, Heung Cho [Urbana, IL; Yoon, Jongseung [Urbana, IL; Menard, Etienne [Durham, NC; Baca, Alfred J [Urbana, IL

2011-04-26

Provided are methods for making a device or device component by providing a multilayer structure having a plurality of functional layers and a plurality of release layers and releasing the functional layers from the multilayer structure by separating one or more of the release layers to generate a plurality of transferable structures. The transferable structures are printed onto a device substrate or device component supported by a device substrate. The methods and systems provide means for making high-quality and low-cost photovoltaic devices, transferable semiconductor structures, (opto-)electronic devices and device components.

Release strategies for making transferable semiconductor structures, devices and device components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rogers, John A.; Nuzzo, Ralph G.; Meitl, Matthew

2016-05-24

Provided are methods for making a device or device component by providing a multi layer structure having a plurality of functional layers and a plurality of release layers and releasing the functional layers from the multilayer structure by separating one or more of the release layers to generate a plurality of transferable structures. The transferable structures are printed onto a device substrate or device component supported by a device substrate. The methods and systems provide means for making high-quality and low-cost photovoltaic devices, transferable semiconductor structures, (opto-)electronic devices and device components.

21 CFR 872.1745 - Laser fluorescence caries detection device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Laser fluorescence caries detection device. 872... SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1745 Laser fluorescence caries detection device. (a) Identification. A laser fluorescence caries detection device is a laser, a...

Extending Wi-Fi Direct for Automated Operations

DTIC Science & Technology

2015-03-01

functionalities. These added functionalities include: automatic device discovery, a mutual awareness of capabilities between devices (inter-device capability ...functionalities include: automatic device discove1y, a mutual awareness of capabilities between devices (inter-device capability awareness...Figure 7. P2P Device GO Negotiation Request (The P2P IE includes P2P Capability , P2P Device Info, Group Owner Intent, Configuration Timeout, Listen

21 CFR 884.5360 - Contraceptive intrauterine device (IUD) and introducer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Contraceptive intrauterine device (IUD) and... Gynecological Therapeutic Devices § 884.5360 Contraceptive intrauterine device (IUD) and introducer. (a) Identification. A contraceptive intrauterine device (IUD) is a device used to prevent pregnancy. The device is...

21 CFR 884.5360 - Contraceptive intrauterine device (IUD) and introducer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Contraceptive intrauterine device (IUD) and... Gynecological Therapeutic Devices § 884.5360 Contraceptive intrauterine device (IUD) and introducer. (a) Identification. A contraceptive intrauterine device (IUD) is a device used to prevent pregnancy. The device is...

21 CFR 884.5360 - Contraceptive intrauterine device (IUD) and introducer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Contraceptive intrauterine device (IUD) and... Gynecological Therapeutic Devices § 884.5360 Contraceptive intrauterine device (IUD) and introducer. (a) Identification. A contraceptive intrauterine device (IUD) is a device used to prevent pregnancy. The device is...

21 CFR 884.5360 - Contraceptive intrauterine device (IUD) and introducer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Contraceptive intrauterine device (IUD) and... Gynecological Therapeutic Devices § 884.5360 Contraceptive intrauterine device (IUD) and introducer. (a) Identification. A contraceptive intrauterine device (IUD) is a device used to prevent pregnancy. The device is...

21 CFR 884.5360 - Contraceptive intrauterine device (IUD) and introducer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Contraceptive intrauterine device (IUD) and... Gynecological Therapeutic Devices § 884.5360 Contraceptive intrauterine device (IUD) and introducer. (a) Identification. A contraceptive intrauterine device (IUD) is a device used to prevent pregnancy. The device is...

21 CFR 872.2060 - Jaw tracking device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Jaw tracking device. 872.2060 Section 872.2060 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2060 Jaw tracking device. (a) Jaw tracking device...

21 CFR 872.2060 - Jaw tracking device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Jaw tracking device. 872.2060 Section 872.2060 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2060 Jaw tracking device. (a) Jaw tracking device...

21 CFR 872.2060 - Jaw tracking device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Jaw tracking device. 872.2060 Section 872.2060 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2060 Jaw tracking device. (a) Jaw tracking device...

21 CFR 872.2060 - Jaw tracking device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Jaw tracking device. 872.2060 Section 872.2060 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.2060 Jaw tracking device. (a) Jaw tracking device...

21 CFR 801.437 - User labeling for devices that contain natural rubber.

Code of Federal Regulations, 2014 CFR

2014-04-01

... User labeling for devices that contain natural rubber. (a) Data in the Medical Device Reporting System... of the device packaging, the outside package, container or wrapper, and the immediate device package... panel of the device packaging, the outside package, container or wrapper, and the immediate device...

21 CFR 801.437 - User labeling for devices that contain natural rubber.

Code of Federal Regulations, 2011 CFR

2011-04-01

... User labeling for devices that contain natural rubber. (a) Data in the Medical Device Reporting System... of the device packaging, the outside package, container or wrapper, and the immediate device package... panel of the device packaging, the outside package, container or wrapper, and the immediate device...

21 CFR 801.437 - User labeling for devices that contain natural rubber.

Code of Federal Regulations, 2013 CFR

2013-04-01

... User labeling for devices that contain natural rubber. (a) Data in the Medical Device Reporting System... of the device packaging, the outside package, container or wrapper, and the immediate device package... panel of the device packaging, the outside package, container or wrapper, and the immediate device...

21 CFR 801.437 - User labeling for devices that contain natural rubber.

Code of Federal Regulations, 2012 CFR

2012-04-01

... User labeling for devices that contain natural rubber. (a) Data in the Medical Device Reporting System... of the device packaging, the outside package, container or wrapper, and the immediate device package... panel of the device packaging, the outside package, container or wrapper, and the immediate device...

21 CFR 801.437 - User labeling for devices that contain natural rubber.

Code of Federal Regulations, 2010 CFR

2010-04-01

... User labeling for devices that contain natural rubber. (a) Data in the Medical Device Reporting System... of the device packaging, the outside package, container or wrapper, and the immediate device package... panel of the device packaging, the outside package, container or wrapper, and the immediate device...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bolenbaugh, Jonathan M.; Naqi, Syed

A method to operate a clutch device in an electro-mechanical transmission mechanically-operatively coupled to an internal combustion engine and at least one electric machine includes, in response to a failure condition detected within a flow control device configured to facilitate flow of hydraulic fluid for operating the clutch device, selectively preventing the flow of hydraulic fluid from entering the flow control device and feeding the clutch device. Synchronization of the clutch device is initiated when the clutch device is intended for activation, and only if the clutch device is synchronized, the flow of hydraulic fluid is selectively permitted to entermore » the flow control device to activate the clutch device.« less

Evaluation of an investigational wearable injector in healthy human volunteers.

PubMed

Torjman, Marc C; Machnicki, Robert; Lessin, Jennifer; Loeum, Channy; Steinberger, Douglas; Mycroft, Sarah; Joseph, Jeffrey I

2017-01-01

Introduction of a wearable device for subcutaneous delivery of larger volume bolus injections would encourage patient compliance and reduce the burden on healthcare services. With one such wearable device commercially available, this study examined the safety and functionality of an investigational device in volunteers. Four devices were applied to the subject's abdomen: 1) Investigational Device, 2) Investigational Device: subject movement, 3) Control Device: FDA-cleared syringe driver with FDA-cleared infusion set, 4) Control Device: FDA-cleared syringe driver attached to investigational device. Three milliliters of saline were infused through the four devices over 3 minutes. 84 devices were applied to 21 subjects. Three milliliters of saline were safely delivered subcutaneously from the investigational and control devices. Two control devices had occlusions and in each case the pump reached its high pressure limit of 12 psi. VAS pain measurements showed minimal pain for all subjects. Pain scores were significantly (p < 0.001) higher than baseline at the end of injection: mean pain level ranged from 2.0-22.0 mm. The investigational device performed as intended with minimal pain during needle insertion and infusion, and no leaking of fluid at the skin puncture site. Two occlusions occurred with the control devices.

77 FR 18829 - Gastroenterology and Urology Devices Panel of the Medical Devices Advisory Committee; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-28

...] Gastroenterology and Urology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY... public. Name of Committee: Gastroenterology and Urology Devices Panel of the Medical Devices Advisory... and 11, 2012, the committee will discuss general issues related to medical devices intended for obese...

78 FR 77688 - Ophthalmic Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

...] Ophthalmic Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Ophthalmic Devices Panel of the Medical Devices Advisory Committee. General Function of the Committee: To... Swink, Center for Devices and Radiological Health, Food and Drug Administration, 10903 New Hampshire Ave...

21 CFR 880.6310 - Medical device data system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... medical device data; (ii) The electronic storage of medical device data; (iii) The electronic conversion... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Medical device data system. 880.6310 Section 880... Devices § 880.6310 Medical device data system. (a) Identification. (1) A medical device data system (MDDS...

21 CFR 880.6310 - Medical device data system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... medical device data; (ii) The electronic storage of medical device data; (iii) The electronic conversion... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Medical device data system. 880.6310 Section 880... Devices § 880.6310 Medical device data system. (a) Identification. (1) A medical device data system (MDDS...

21 CFR 880.6310 - Medical device data system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... medical device data; (ii) The electronic storage of medical device data; (iii) The electronic conversion... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Medical device data system. 880.6310 Section 880... Devices § 880.6310 Medical device data system. (a) Identification. (1) A medical device data system (MDDS...

21 CFR 880.6310 - Medical device data system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... medical device data; (ii) The electronic storage of medical device data; (iii) The electronic conversion... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Medical device data system. 880.6310 Section 880... Devices § 880.6310 Medical device data system. (a) Identification. (1) A medical device data system (MDDS...

76 FR 29006 - In the Matter of Certain Motion-Sensitive Sound Effects Devices and Image Display Devices and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-19

... Effects Devices and Image Display Devices and Components and Products Containing Same; Notice of... United States after importation of certain motion-sensitive sound effects devices and image display... devices and image display devices and components and products containing same that infringe one or more of...

CONTROL LIMITER DEVICE

DOEpatents

DeShong, J.A.

1960-03-01

A control-limiting device for monltoring a control system is described. The system comprises a conditionsensing device, a condition-varying device exerting a control over the condition, and a control means to actuate the condition-varying device. A control-limiting device integrates the total movement or other change of the condition-varying device over any interval of time during a continuum of overlapping periods of time, and if the tothl movement or change of the condition-varying device exceeds a preset value, the control- limiting device will switch the control of the operated apparatus from automatic to manual control.

Eager protocol on a cache pipeline dataflow

DOEpatents

Ohmacht, Martin; Sugavanam, Krishnan

2012-11-13

A master device sends a request to communicate with a slave device to a switch. The master device waits for a period of cycles the switch takes to decide whether the master device can communicate with the slave device, and the master device sends data associated with the request to communicate at least after the period of cycles has passed since the master device sent the request to communicate to the switch without waiting to receive an acknowledgment from the switch that the master device can communicate with the slave device.

Two Different Maintenance Strategies in the Hospital Environment: Preventive Maintenance for Older Technology Devices and Predictive Maintenance for Newer High-Tech Devices.

PubMed

Sezdi, Mana

2016-01-01

A maintenance program generated through the consideration of characteristics and failures of medical equipment is an important component of technology management. However, older technology devices and newer high-tech devices cannot be efficiently managed using the same strategies because of their different characteristics. This study aimed to generate a maintenance program comprising two different strategies to increase the efficiency of device management: preventive maintenance for older technology devices and predictive maintenance for newer high-tech devices. For preventive maintenance development, 589 older technology devices were subjected to performance verification and safety testing (PVST). For predictive maintenance development, the manufacturers' recommendations were used for 134 high-tech devices. These strategies were evaluated in terms of device reliability. This study recommends the use of two different maintenance strategies for old and new devices at hospitals in developing countries. Thus, older technology devices that applied only corrective maintenance will be included in maintenance like high-tech devices.

Two Different Maintenance Strategies in the Hospital Environment: Preventive Maintenance for Older Technology Devices and Predictive Maintenance for Newer High-Tech Devices

PubMed Central

Sezdi, Mana

2016-01-01

A maintenance program generated through the consideration of characteristics and failures of medical equipment is an important component of technology management. However, older technology devices and newer high-tech devices cannot be efficiently managed using the same strategies because of their different characteristics. This study aimed to generate a maintenance program comprising two different strategies to increase the efficiency of device management: preventive maintenance for older technology devices and predictive maintenance for newer high-tech devices. For preventive maintenance development, 589 older technology devices were subjected to performance verification and safety testing (PVST). For predictive maintenance development, the manufacturers' recommendations were used for 134 high-tech devices. These strategies were evaluated in terms of device reliability. This study recommends the use of two different maintenance strategies for old and new devices at hospitals in developing countries. Thus, older technology devices that applied only corrective maintenance will be included in maintenance like high-tech devices. PMID:27195666

Radiology of cardiac devices and their complications

PubMed Central

Dipoce, J; Spindola-Franco, H

2015-01-01

This article familiarizes the reader with several different cardiac devices including pacemakers and implantable cardioverter defibrillators, intra-aortic balloon pumps, ventricular assist devices, valve replacements and repairs, shunt-occluding devices and passive constraint devices. Many cardiac devices are routinely encountered in clinical practice. Other devices are in the early stages of development, but circumstances suggest that they too will become commonly found. The radiologist must be familiar with these devices and their complications. PMID:25411826

Wireless device monitoring systems and monitoring devices, and associated methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCown, Steven H; Derr, Kurt W; Rohde, Kenneth W

Wireless device monitoring systems and monitoring devices include a communications module for receiving wireless communications of a wireless device. Processing circuitry is coupled with the communications module and configured to process the wireless communications to determine whether the wireless device is authorized or unauthorized to be present at the monitored area based on identification information of the wireless device. Methods of monitoring for the presence and identity of wireless devices are also provided.

Localized electrical fine tuning of passive microwave and radio frequency devices

DOEpatents

Findikoglu, Alp T.

2001-04-10

A method and apparatus for the localized electrical fine tuning of passive multiple element microwave or RF devices in which a nonlinear dielectric material is deposited onto predetermined areas of a substrate containing the device. An appropriate electrically conductive material is deposited over predetermined areas of the nonlinear dielectric and the signal line of the device for providing electrical contact with the nonlinear dielectric. Individual, adjustable bias voltages are applied to the electrically conductive material allowing localized electrical fine tuning of the devices. The method of the present invention can be applied to manufactured devices, or can be incorporated into the design of the devices so that it is applied at the time the devices are manufactured. The invention can be configured to provide localized fine tuning for devices including but not limited to coplanar waveguides, slotline devices, stripline devices, and microstrip devices.

Processing module operating methods, processing modules, and communications systems

DOEpatents

McCown, Steven Harvey; Derr, Kurt W.; Moore, Troy

2014-09-09

A processing module operating method includes using a processing module physically connected to a wireless communications device, requesting that the wireless communications device retrieve encrypted code from a web site and receiving the encrypted code from the wireless communications device. The wireless communications device is unable to decrypt the encrypted code. The method further includes using the processing module, decrypting the encrypted code, executing the decrypted code, and preventing the wireless communications device from accessing the decrypted code. Another processing module operating method includes using a processing module physically connected to a host device, executing an application within the processing module, allowing the application to exchange user interaction data communicated using a user interface of the host device with the host device, and allowing the application to use the host device as a communications device for exchanging information with a remote device distinct from the host device.

Wafer bonded epitaxial templates for silicon heterostructures

DOEpatents

Atwater, Jr., Harry A.; Zahler, James M [Pasadena, CA; Morral, Anna Fontcubera I [Paris, FR

2008-03-11

A heterostructure device layer is epitaxially grown on a virtual substrate, such as an InP/InGaAs/InP double heterostructure. A device substrate and a handle substrate form the virtual substrate. The device substrate is bonded to the handle substrate and is composed of a material suitable for fabrication of optoelectronic devices. The handle substrate is composed of a material suitable for providing mechanical support. The mechanical strength of the device and handle substrates is improved and the device substrate is thinned to leave a single-crystal film on the virtual substrate such as by exfoliation of a device film from the device substrate. An upper portion of the device film exfoliated from the device substrate is removed to provide a smoother and less defect prone surface for an optoelectronic device. A heterostructure is epitaxially grown on the smoothed surface in which an optoelectronic device may be fabricated.

Photoelectrochemically driven self-assembly method

DOEpatents

Nielson, Gregory N.; Okandan, Murat

2017-01-17

Various technologies described herein pertain to assembling electronic devices into a microsystem. The electronic devices are disposed in a solution. Light can be applied to the electronic devices in the solution. The electronic devices can generate currents responsive to the light applied to the electronic devices in the solution, and the currents can cause electrochemical reactions that functionalize regions on surfaces of the electronic devices. Additionally or alternatively, the light applied to the electronic devices in the solution can cause the electronic devices to generate electric fields, which can orient the electronic devices and/or induce movement of the electronic devices with respect to a receiving substrate. Further, electrodes on a receiving substrate can be biased to attract and form connections with the electronic devices having the functionalized regions on the surfaces. The microsystem can include the receiving substrate and the electronic devices connected to the receiving substrate.

Wafer bonded epitaxial templates for silicon heterostructures

NASA Technical Reports Server (NTRS)

Atwater, Harry A., Jr. (Inventor); Zahler, James M. (Inventor); Morral, Anna Fontcubera I (Inventor)

2008-01-01

A heterostructure device layer is epitaxially grown on a virtual substrate, such as an InP/InGaAs/InP double heterostructure. A device substrate and a handle substrate form the virtual substrate. The device substrate is bonded to the handle substrate and is composed of a material suitable for fabrication of optoelectronic devices. The handle substrate is composed of a material suitable for providing mechanical support. The mechanical strength of the device and handle substrates is improved and the device substrate is thinned to leave a single-crystal film on the virtual substrate such as by exfoliation of a device film from the device substrate. An upper portion of the device film exfoliated from the device substrate is removed to provide a smoother and less defect prone surface for an optoelectronic device. A heterostructure is epitaxially grown on the smoothed surface in which an optoelectronic device may be fabricated.

Event-recording devices with identification codes

NASA Technical Reports Server (NTRS)

Watters, David G. (Inventor); Huestis, David L. (Inventor); Bahr, Alfred J. (Inventor); Vidmar, Robert J. (Inventor)

2003-01-01

A recording device allows wireless interrogation to determine its identity and its state. The state indicates whether one or more physical or chemical events have taken place. In effect, the one or more physical or chemical events are recorded by the device. The identity of the device allows it to be distinguished from a number of similar devices. The recording device may be used in an array of devices that allows wireless probing by an interrogation unit. When probed, each device tells the interrogator who it is and what state it is in. The devices allow multiple use and the interrogator may use a logical reset to determine the state of each device. The interrogator can thus easily identify particular items in an array that have reached a particular condition. The device may record the status of each device in a database to maintain a history for each.

Evaluation of Tissue Interactions with Mechanical Elements of a Transscleral Drug Delivery Device

PubMed Central

Cohen, Sarah J.; Chan, Robison V. Paul; Keegan, Mark; Andreoli, Christopher M.; Borenstein, Jeffrey T.; Miller, Joan W.; Gragoudas, Evangelos S.

2012-01-01

The goal of this work was to evaluate tissue-device interactions due to implantation of a mechanically operated drug delivery system onto the posterior sclera. Two test devices were designed and fabricated to model elements of the drug delivery device—one containing a free-spinning ball bearing and the other encasing two articulating gears. Openings in the base of test devices modeled ports for drug passage from device to sclera. Porous poly(tetrafluoroethylene) (PTFE) membranes were attached to half of the gear devices to minimize tissue ingrowth through these ports. Test devices were sutured onto rabbit eyes for 10 weeks. Tissue-device interactions were evaluated histologically and mechanically after removal to determine effects on device function and changes in surrounding tissue. Test devices were generally well-tolerated during residence in the animal. All devices encouraged fibrous tissue formation between the sclera and the device, fibrous tissue encapsulation and invasion around the device, and inflammation of the conjunctiva. Gear devices encouraged significantly greater inflammation in all cases and a larger rate of tissue ingrowth. PTFE membranes prevented tissue invasion through the covered drug ports, though tissue migrated in through other smaller openings. The torque required to turn the mechanical elements increased over 1000 times for gear devices, but only on the order of 100 times for membrane-covered gear devices and less than 100 times for ball bearing devices. Maintaining a lower device profile, minimizing microscale motion on the eye surface and covering drug ports with a porous membrane may minimize inflammation, decreasing the risk of damage to surrounding tissues and minimizing disruption of device operation. PMID:24300189

What people know about electronic devices: A descriptive study

NASA Astrophysics Data System (ADS)

Kieras, D. E.

1982-10-01

Informal descriptive results on the nature of people's natural knowledge of electronic devices are presented. Expert and nonexpert subjects were given an electronic device to examine and describe orally. The devices ranged from familiar everyday devices, to those familiar only to the expert, to unusual devices unfamiliar even to an expert. College students were asked to describe everyday devices from memory. The results suggest that device knowledge consists of the major categories of what the device is for, how it is used, its structure in terms of subdevices, its physical layout, how it works, and its behavior. A preliminary theoretical framework for device knowledge is that it consists of a hierarchy of schemas, corresponding to a hierarchial decomposition of the device into subdevices, with each level containing the major categories of information.

75 FR 35495 - Ophthalmic Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-22

...] Ophthalmic Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Ophthalmic Devices Panel of the Medical Devices Advisory Committee. General Function of the Committee: To... Glaukos iStent Trabecular Micro-Bypass Stent, Model GTS-100 L/R, sponsored by Glaukos Corp. The device is...

76 FR 50485 - Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee; Amendment of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-15

...] Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice AGENCY... an amendment to the notice of meeting of the Obstetrics and Gynecology Devices Panel of the Medical... Obstetrics and Gynecology Devices Panel of the Medical Devices Advisory Committee would be held on September...

75 FR 61507 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-05

...] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice... announcing an amendment to the notice of meeting of the General and Plastic Surgery Devices Panel of the..., FDA announced that a meeting of the General and Plastic Surgery Devices Panel of the Medical Devices...

Hardware device binding and mutual authentication

DOEpatents

Hamlet, Jason R; Pierson, Lyndon G

2014-03-04

Detection and deterrence of device tampering and subversion by substitution may be achieved by including a cryptographic unit within a computing device for binding multiple hardware devices and mutually authenticating the devices. The cryptographic unit includes a physically unclonable function ("PUF") circuit disposed in or on the hardware device, which generates a binding PUF value. The cryptographic unit uses the binding PUF value during an enrollment phase and subsequent authentication phases. During a subsequent authentication phase, the cryptographic unit uses the binding PUF values of the multiple hardware devices to generate a challenge to send to the other device, and to verify a challenge received from the other device to mutually authenticate the hardware devices.

78 FR 1247 - Certain Electronic Devices, Including Wireless Communication Devices, Tablet Computers, Media...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-08

... Wireless Communication Devices, Tablet Computers, Media Players, and Televisions, and Components Thereof... devices, including wireless communication devices, tablet computers, media players, and televisions, and... wireless communication devices, tablet computers, media players, and televisions, and components thereof...

Tracking down a solution: exploring the acceptability and value of wearable GPS devices for older persons, individuals with a disability and their support persons.

PubMed

Williamson, Brittany; Aplin, Tammy; de Jonge, Desleigh; Goyne, Matthew

2017-11-01

To explore the acceptability and value of three wearable GPS devices for older persons and individuals with a disability and safety concerns when accessing the community. This pilot study explored six wearers' and their support persons' experience of using three different wearable GPS devices (a pendant, watch, and mini GPS phone), each for a two-week period. Participants identified safety as the main value of using a wearable GPS device. The acceptability and value of these devices was strongly influenced by device features, ease of use, cost, appearance, the reliability of the GPS coordinates, the wearer's health condition and the users familiarity with technology. Overall, participants indicated that they preferred the pendant. Wearable GPS devices are potentially useful in providing individuals who have safety concerns with reassurance and access to assistance as required. To ensure successful utilization, future device design and device selection should consider the user's familiarity with technology and their health condition. This study also revealed that not all wearable GPS devices provide continuous location tracking. It is therefore critical to ensure that the device's location tracking functions address the wearer's requirements and reason for using the device. Implications for Rehabilitation The acceptability and usability of wearable GPS devices is strongly influenced by the device features, ease of use, cost, appearance, the reliability of the device to provide accurate and timely GPS coordinates, as well as the health condition of the wearer and their familiarity with technology. Wearable GPS devices need to be simple to use and support and training is essential to ensure they are successfully utilized. Not all wearable GPS devices provide continuous location tracking and accuracy of location is impacted by line of sight to satellites. Therefore, care needs to be taken when choosing a suitable device, to ensure that the device's location tracking features are based on the wearer's requirements and value behind using the device.

Techniques for trans-catheter retrieval of embolized Nit-Occlud® PDA-R and ASD-R devices.

PubMed

Sinha, Sanjay; Levi, Daniel; Peirone, Alejandro; Pedra, Carlos

2018-02-15

Nit-Occlud ® (atrial septal defect) ASD-R and (patent ductus arteriosus) PDA-R devices are used outside the United States for percutaneous closure of the patent ductus arteriosus and atrial septal defects. When embolization occurs, these devices have been difficult to retrieve. Bench simulations of retrieval of PDA-R and ASD-R devices were performed in a vascular model. Retrieval of each device was attempted using snare techniques or with bioptome forceps with a range of devices. The same devices were then intentionally embolized in an animal model. Retrieval methods were systematically tested in a range of sheath sizes, and graded in terms of difficulty and retrieval time. Devices that were grasped by the bioptome in the center of the proximal part of the devices were easily retrieved in both models. Bench studies determined the minimum sheath sizes needed for retrieval of each device with this method. In general sheathes two french sizes greater than the delivery sheath were successful with this technique. Three out of the four PDA-R devices were successfully retrieved in vivo. Two were retrieved by grasping the middle of the PA end of the PDA-R device with a Maslanka bioptome and one small PDA-R device was retrieved using a 10 mm Snare. Four of the five ASD-R devices were retrieved successfully grasping the right atrial ASD-R disc or by passing a wire through the device and snaring this loop. For ASD-R 28 and 30 mm devices, a double bioptome technique was needed to retrieve the device. ASD-R and PDA-R devices can be successfully retrieved in the catheterization lab. It is critical to grab the center portion of the right atrial disc of the ASD-R device or pulmonary portion of the PDA-R device and to use adequately sized sheathes. © 2018 Wiley Periodicals, Inc.

Applications and Methods of Operating a Three-dimensional Nano-electro-mechanical Resonator and Related Devices

NASA Technical Reports Server (NTRS)

Kaul, Anupama B. (Inventor); Epp, Larry W. (Inventor); Bagge, Leif (Inventor)

2013-01-01

Carbon nanofiber resonator devices, methods for use, and applications of said devices are disclosed. Carbon nanofiber resonator devices can be utilized in or as high Q resonators. Resonant frequency of these devices is a function of configuration of various conducting components within these devices. Such devices can find use, for example, in filtering and chemical detection.

Current state of medical device nomenclature and taxonomy systems in the UK: spotlight on GMDN and SNOMED CT

PubMed Central

White, Judith; Carolan-Rees, Grace

2013-01-01

A standardised terminology for describing medical devices can enable safe and unambiguous exchange of information. Proposed changes to EU-wide medical devices regulations mandate the use of such a system. This article reviews two important classification systems for medical devices in the UK. The Global Medical Device Nomenclature (GMDN) provides a classification system specifically for medical devices and diagnostics, and facilitates data exchange between manufacturers and regulators. SNOMED CT is the terminology of choice in the NHS for communicating, sharing and storing information about patients’ healthcare episodes. Harmonisation of GMDN and SNOMED CT will encourage use of single terminology throughout the lifetime of a device; from regulatory approval through clinical use and post-marketing surveillance. Manufacturers will be required to register medical devices with a European device database (Eudamed) and to fit certain devices with a Unique Device Identifier; both are efforts to improve transparency and traceability of medical devices. Successful implementation of these elements depends on having a consistent nomenclature for medical devices. PMID:23885299

Examining the Relationship between Parental Involvement and Mobile Technology Use

NASA Astrophysics Data System (ADS)

Flowers, Toinette M.

Understanding how mobile devices can enhance parent/teacher communication is important because parents play an important part in their children's learning. Research on parents' use of mobile devices to communicate with their children's teachers is limited. The purpose of this cross-sectional correlational study was to determine the relationships between parents' (a) knowledge of using mobile devices, (b) general use of mobile devices, (c) purpose for using mobile devices, (d) perceived ease of using mobile devices, (e) perceived usefulness of mobile devices, (f) attitude toward using mobile devices, and (g) use of mobile devices to communicate with teachers. The study was informed by the technology acceptance model and used a participant pool of 73 parents of high school students attending a Title I high school in a large Midwestern city in the United States. Data were collected using an online survey and analyzed using Pearson's correlations. The study results indicate significant correlations between parents' use of mobile devices to communicate with teachers and knowledge of using mobile devices, purpose for using mobile devices, perceived ease of using mobile devices, perceived usefulness of mobile devices, and attitudes toward using mobile devices. These findings suggest that parental use of mobile devices to communicate with teachers can be enhanced by administrators and school personnel using strategies that consider parents' and the school culture. Social implication includes sharing the results of this study with district and school administrators who have the power to implement programs that encourage and support the use of mobile devices as a communication tool between parents and teachers, therefore increasing parental involvement and ultimately student academic success.

21 CFR 882.5050 - Biofeedback device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Biofeedback device. 882.5050 Section 882.5050 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Therapeutic Devices § 882.5050 Biofeedback device. (a...

21 CFR 872.3660 - Impression material.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3660 Impression material. (a) Identification. Impression material is a device composed of materials such as alginate or polysulfide intended to be placed... device is intended to provide models for study and for production of restorative prosthetic devices, such...

21 CFR 872.3660 - Impression material.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) MEDICAL DEVICES DENTAL DEVICES Prosthetic Devices § 872.3660 Impression material. (a) Identification. Impression material is a device composed of materials such as alginate or polysulfide intended to be placed... device is intended to provide models for study and for production of restorative prosthetic devices, such...

78 FR 24775 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-26

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-745] Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and Components Thereof; Commission Decision... importation of certain wireless communication devices, portable music and data processing devices, computers...

78 FR 12785 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-25

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-745] Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and Components Thereof; Commission Decision... importation of certain wireless communication devices, portable music and data processing devices, computers...

Three fundamental devices in one: a reconfigurable multifunctional device in two-dimensional WSe2

NASA Astrophysics Data System (ADS)

Dhakras, Prathamesh; Agnihotri, Pratik; Lee, Ji Ung

2017-06-01

The three pillars of semiconductor device technologies are (1) the p-n diode, (2) the metal-oxide-semiconductor field-effect transistor and (3) the bipolar junction transistor. They have enabled the unprecedented growth in the field of information technology that we see today. Until recently, the technological revolution for better, faster and more efficient devices has been governed by scaling down the device dimensions following Moore’s Law. With the slowing of Moore’s law, there is a need for alternative materials and computing technologies that can continue the advancement in functionality. Here, we describe a single, dynamically reconfigurable device that implements these three fundamental device functions. The device uses buried gates to achieve n- and p-channels and fits into a larger effort to develop devices with enhanced functionalities, including logic functions, over device scaling. As they are all surface conducting devices, we use one material parameter, the interface trap density of states, to describe the key figure-of-merit of each device.

Content analysis of Australian direct-to-consumer websites for emerging breast cancer imaging devices.

PubMed

Vreugdenburg, Thomas D; Laurence, Caroline O; Willis, Cameron D; Mundy, Linda; Hiller, Janet E

2014-09-01

To describe the nature and frequency of information presented on direct-to-consumer websites for emerging breast cancer imaging devices. Content analysis of Australian website advertisements from 2 March 2011 to 30 March 2012, for three emerging breast cancer imaging devices: digital infrared thermal imaging, electrical impedance scanning and electronic palpation imaging. Type of imaging offered, device safety, device performance, application of device, target population, supporting evidence and comparator tests. Thirty-nine unique Australian websites promoting a direct-to-consumer breast imaging device were identified. Despite a lack of supporting evidence, 22 websites advertised devices for diagnosis, 20 advertised devices for screening, 13 advertised devices for prevention and 13 advertised devices for identifying breast cancer risk factors. Similarly, advertised ranges of diagnostic sensitivity (78%-99%) and specificity (44%-91%) were relatively high compared with published literature. Direct comparisons with conventional screening tools that favoured the new device were highly prominent (31 websites), and one-third of websites (12) explicitly promoted their device as a suitable alternative. Australian websites for emerging breast imaging devices, which are also available internationally, promote the use of such devices as safe and effective solutions for breast cancer screening and diagnosis in a range of target populations. Many of these claims are not supported by peer-reviewed evidence, raising questions about the manner in which these devices and their advertising material are regulated, particularly when they are promoted as direct alternatives to established screening interventions.

Lossless hybridization between photovoltaic and thermoelectric devices.

PubMed

Park, Kwang-Tae; Shin, Sun-Mi; Tazebay, Abdullah S; Um, Han-Don; Jung, Jin-Young; Jee, Sang-Won; Oh, Min-Wook; Park, Su-Dong; Yoo, Bongyoung; Yu, Choongho; Lee, Jung-Ho

2013-01-01

The optimal hybridization of photovoltaic (PV) and thermoelectric (TE) devices has long been considered ideal for the efficient harnessing solar energy. Our hybrid approach uses full spectrum solar energy via lossless coupling between PV and TE devices while collecting waste energy from thermalization and transmission losses from PV devices. Achieving lossless coupling makes the power output from the hybrid device equal to the sum of the maximum power outputs produced separately from individual PV and TE devices. TE devices need to have low internal resistances enough to convey photo-generated currents without sacrificing the PV fill factor. Concomitantly, a large number of p-n legs are preferred to drive a high Seebeck voltage in TE. Our simple method of attaching a TE device to a PV device has greatly improved the conversion efficiency and power output of the PV device (~30% at a 15°C temperature gradient across a TE device).

Lossless hybridization between photovoltaic and thermoelectric devices

PubMed Central

Park, Kwang-Tae; Shin, Sun-Mi; Tazebay, Abdullah S.; Um, Han-Don; Jung, Jin-Young; Jee, Sang-Won; Oh, Min-Wook; Park, Su-Dong; Yoo, Bongyoung; Yu, Choongho; Lee, Jung-Ho

2013-01-01

The optimal hybridization of photovoltaic (PV) and thermoelectric (TE) devices has long been considered ideal for the efficient harnessing solar energy. Our hybrid approach uses full spectrum solar energy via lossless coupling between PV and TE devices while collecting waste energy from thermalization and transmission losses from PV devices. Achieving lossless coupling makes the power output from the hybrid device equal to the sum of the maximum power outputs produced separately from individual PV and TE devices. TE devices need to have low internal resistances enough to convey photo-generated currents without sacrificing the PV fill factor. Concomitantly, a large number of p-n legs are preferred to drive a high Seebeck voltage in TE. Our simple method of attaching a TE device to a PV device has greatly improved the conversion efficiency and power output of the PV device (~30% at a 15°C temperature gradient across a TE device). PMID:23820973

21 CFR 882.4250 - Cryogenic surgical device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Cryogenic surgical device. 882.4250 Section 882.4250 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4250 Cryogenic surgical device...

21 CFR 882.4250 - Cryogenic surgical device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cryogenic surgical device. 882.4250 Section 882.4250 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4250 Cryogenic surgical device...

21 CFR 872.1870 - Sulfide detection device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Sulfide detection device. 872.1870 Section 872.1870 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1870 Sulfide detection device. (a) Identification...

21 CFR 872.1740 - Caries detection device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Caries detection device. 872.1740 Section 872.1740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1740 Caries detection device. (a) Identification...

21 CFR 872.1740 - Caries detection device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Caries detection device. 872.1740 Section 872.1740 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1740 Caries detection device. (a) Identification...

78 FR 68853 - International Medical Device Regulators Forum; Medical Device Single Audit Program International...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

...] International Medical Device Regulators Forum; Medical Device Single Audit Program International Coalition Pilot... Drug Administration (FDA) is announcing participation in the Medical Device Single Audit Program International Coalition Pilot Program. The Medical Device Single Audit Program (MDSAP) was designed and...

21 CFR 866.2580 - Gas-generating device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Gas-generating device. 866.2580 Section 866.2580 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Microbiology Devices § 866.2580 Gas-generating device...

21 CFR 866.2580 - Gas-generating device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Gas-generating device. 866.2580 Section 866.2580 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Microbiology Devices § 866.2580 Gas-generating device...

21 CFR 866.2580 - Gas-generating device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Gas-generating device. 866.2580 Section 866.2580 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Microbiology Devices § 866.2580 Gas-generating device...

21 CFR 866.2580 - Gas-generating device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Gas-generating device. 866.2580 Section 866.2580 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Microbiology Devices § 866.2580 Gas-generating device...

21 CFR 866.2580 - Gas-generating device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Gas-generating device. 866.2580 Section 866.2580 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Microbiology Devices § 866.2580 Gas-generating device...

77 FR 52759 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-30

... INTERNATIONAL TRADE COMMISSION [Investigation No. 337-TA-745] Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers and Components Thereof; Notice of... communication devices, portable music and data processing devices, computers and components thereof by reason of...

77 FR 51571 - Certain Wireless Communication Devices, Portable Music and Data Processing Devices, Computers...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-24

... Music and Data Processing Devices, Computers, and Components Thereof; Notice of Receipt of Complaint... complaint entitled Wireless Communication Devices, Portable Music and Data Processing Devices, Computers..., portable music and data processing devices, computers, and components thereof. The complaint names as...

21 CFR 874.5840 - Antistammering device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Antistammering device. 874.5840 Section 874.5840 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5840 Antistammering device. (a...

21 CFR 874.5840 - Antistammering device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Antistammering device. 874.5840 Section 874.5840 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5840 Antistammering device. (a...

21 CFR 874.5840 - Antistammering device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Antistammering device. 874.5840 Section 874.5840 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5840 Antistammering device. (a...

21 CFR 874.5840 - Antistammering device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Antistammering device. 874.5840 Section 874.5840 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5840 Antistammering device. (a...

21 CFR 810.10 - Cease distribution and notification order.

Code of Federal Regulations, 2010 CFR

2010-04-01

... (CONTINUED) MEDICAL DEVICES MEDICAL DEVICE RECALL AUTHORITY Mandatory Medical Device Recall Procedures § 810... usual name of the device; (iii) The model, catalog, or product code numbers of the device; and (iv) The... opportunity to consult with the agency, FDA finds that there is a reasonable probability that a device...

21 CFR 810.10 - Cease distribution and notification order.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) MEDICAL DEVICES MEDICAL DEVICE RECALL AUTHORITY Mandatory Medical Device Recall Procedures § 810... usual name of the device; (iii) The model, catalog, or product code numbers of the device; and (iv) The... opportunity to consult with the agency, FDA finds that there is a reasonable probability that a device...

21 CFR 884.5380 - Contraceptive tubal occlusion device (TOD) and introducer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Contraceptive tubal occlusion device (TOD) and... Gynecological Therapeutic Devices § 884.5380 Contraceptive tubal occlusion device (TOD) and introducer. (a) Identification. A contraceptive tubal occlusion device (TOD) and introducer is a device designed to close a...

21 CFR 884.5380 - Contraceptive tubal occlusion device (TOD) and introducer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Contraceptive tubal occlusion device (TOD) and... Gynecological Therapeutic Devices § 884.5380 Contraceptive tubal occlusion device (TOD) and introducer. (a) Identification. A contraceptive tubal occlusion device (TOD) and introducer is a device designed to close a...

21 CFR 884.5380 - Contraceptive tubal occlusion device (TOD) and introducer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Contraceptive tubal occlusion device (TOD) and... Gynecological Therapeutic Devices § 884.5380 Contraceptive tubal occlusion device (TOD) and introducer. (a) Identification. A contraceptive tubal occlusion device (TOD) and introducer is a device designed to close a...

21 CFR 884.5380 - Contraceptive tubal occlusion device (TOD) and introducer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Contraceptive tubal occlusion device (TOD) and... Gynecological Therapeutic Devices § 884.5380 Contraceptive tubal occlusion device (TOD) and introducer. (a) Identification. A contraceptive tubal occlusion device (TOD) and introducer is a device designed to close a...

21 CFR 884.5380 - Contraceptive tubal occlusion device (TOD) and introducer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Contraceptive tubal occlusion device (TOD) and... Gynecological Therapeutic Devices § 884.5380 Contraceptive tubal occlusion device (TOD) and introducer. (a) Identification. A contraceptive tubal occlusion device (TOD) and introducer is a device designed to close a...

Integrated device architectures for electrochromic devices

DOEpatents

Frey, Jonathan Mack; Berland, Brian Spencer

2015-04-21

This disclosure describes systems and methods for creating monolithically integrated electrochromic devices which may be a flexible electrochromic device. Monolithic integration of thin film electrochromic devices may involve the electrical interconnection of multiple individual electrochromic devices through the creation of specific structures such as conductive pathway or insulating isolation trenches.

21 CFR 892.1670 - Spot-film device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Spot-film device. 892.1670 Section 892.1670 Food... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1670 Spot-film device. (a) Identification. A spot-film... medical purposes to position a radiographic film cassette to obtain radiographs during fluoroscopy. (b...

21 CFR 892.1670 - Spot-film device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Spot-film device. 892.1670 Section 892.1670 Food... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1670 Spot-film device. (a) Identification. A spot-film... medical purposes to position a radiographic film cassette to obtain radiographs during fluoroscopy. (b...

21 CFR 892.1670 - Spot-film device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Spot-film device. 892.1670 Section 892.1670 Food... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1670 Spot-film device. (a) Identification. A spot-film... medical purposes to position a radiographic film cassette to obtain radiographs during fluoroscopy. (b...

21 CFR 892.1670 - Spot-film device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Spot-film device. 892.1670 Section 892.1670 Food... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1670 Spot-film device. (a) Identification. A spot-film... medical purposes to position a radiographic film cassette to obtain radiographs during fluoroscopy. (b...

76 FR 14028 - Center for Devices and Radiological Health 510(k) Implementation: Online Repository of Medical...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-15

...] Center for Devices and Radiological Health 510(k) Implementation: Online Repository of Medical Device... public meeting entitled ``510(k) Implementation: Discussion of an Online Repository of Medical Device... establish an online public repository of medical device labeling and strategies for displaying device...

76 FR 28689 - Microbiology Devices; Classification of In Vitro Diagnostic Device for Bacillus Species Detection

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-18

.... FDA-2011-N-0103] Microbiology Devices; Classification of In Vitro Diagnostic Device for Bacillus... of the Microbiology Devices Advisory Panel (the Panel). In addition, the proposed rule would... in the Federal Register. 1. Transcript of the FDA Microbiology Devices Panel meeting, March 7, 2002...

21 CFR 892.1670 - Spot-film device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Spot-film device. 892.1670 Section 892.1670 Food... DEVICES RADIOLOGY DEVICES Diagnostic Devices § 892.1670 Spot-film device. (a) Identification. A spot-film... medical purposes to position a radiographic film cassette to obtain radiographs during fluoroscopy. (b...

47 CFR 2.801 - Radiofrequency device defined.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Radiofrequency device defined. 2.801 Section 2... MATTERS; GENERAL RULES AND REGULATIONS Marketing of Radio-frequency Devices § 2.801 Radiofrequency device defined. As used in this part, a radiofrequency device is any device which in its operation is capable of...

21 CFR 886.4170 - Cryophthalmic unit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4170 Cryophthalmic unit. (a) Identification. A cryophthalmic unit is a device that is a probe with a small tip that becomes extremely cold through the controlled use of a refrigerant or gas. The device may be AC-powered. The device is intended to remove...

21 CFR 874.5370 - Tongs antichoke device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Tongs antichoke device. 874.5370 Section 874.5370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5370 Tongs antichoke device. (a...

21 CFR 874.5350 - Suction antichoke device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Suction antichoke device. 874.5350 Section 874.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5350 Suction antichoke device. (a...

21 CFR 874.5350 - Suction antichoke device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Suction antichoke device. 874.5350 Section 874.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5350 Suction antichoke device. (a...

21 CFR 874.5350 - Suction antichoke device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Suction antichoke device. 874.5350 Section 874.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5350 Suction antichoke device. (a...

21 CFR 874.5370 - Tongs antichoke device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Tongs antichoke device. 874.5370 Section 874.5370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5370 Tongs antichoke device. (a...

21 CFR 874.5350 - Suction antichoke device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Suction antichoke device. 874.5350 Section 874.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5350 Suction antichoke device. (a...

21 CFR 874.5350 - Suction antichoke device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Suction antichoke device. 874.5350 Section 874.5350 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5350 Suction antichoke device. (a...

21 CFR 874.5370 - Tongs antichoke device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Tongs antichoke device. 874.5370 Section 874.5370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5370 Tongs antichoke device. (a...

21 CFR 874.5370 - Tongs antichoke device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Tongs antichoke device. 874.5370 Section 874.5370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5370 Tongs antichoke device. (a...

21 CFR 874.5370 - Tongs antichoke device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Tongs antichoke device. 874.5370 Section 874.5370 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Therapeutic Devices § 874.5370 Tongs antichoke device. (a...

21 CFR 864.6100 - Bleeding time device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Bleeding time device. 864.6100 Section 864.6100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Manual Hematology Devices § 864.6100 Bleeding time device...

21 CFR 864.6100 - Bleeding time device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Bleeding time device. 864.6100 Section 864.6100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Manual Hematology Devices § 864.6100 Bleeding time device...

21 CFR 864.6100 - Bleeding time device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Bleeding time device. 864.6100 Section 864.6100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Manual Hematology Devices § 864.6100 Bleeding time device...

21 CFR 864.6100 - Bleeding time device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Bleeding time device. 864.6100 Section 864.6100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Manual Hematology Devices § 864.6100 Bleeding time device...

21 CFR 864.6100 - Bleeding time device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Bleeding time device. 864.6100 Section 864.6100 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES HEMATOLOGY AND PATHOLOGY DEVICES Manual Hematology Devices § 864.6100 Bleeding time device...

21 CFR 878.4930 - Suture retention device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Suture retention device. 878.4930 Section 878.4930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4930 Suture retention device...

21 CFR 878.4930 - Suture retention device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Suture retention device. 878.4930 Section 878.4930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4930 Suture retention device...

21 CFR 878.4930 - Suture retention device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Suture retention device. 878.4930 Section 878.4930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4930 Suture retention device...

21 CFR 878.4930 - Suture retention device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Suture retention device. 878.4930 Section 878.4930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4930 Suture retention device...

21 CFR 878.4930 - Suture retention device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Suture retention device. 878.4930 Section 878.4930 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4930 Suture retention device...

Methods and devices for fabricating and assembling printable semiconductor elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nuzzo, Ralph G.; Rogers, John A.; Menard, Etienne

The invention provides methods and devices for fabricating printable semiconductor elements and assembling printable semiconductor elements onto substrate surfaces. Methods, devices and device components of the present invention are capable of generating a wide range of flexible electronic and optoelectronic devices and arrays of devices on substrates comprising polymeric materials. The present invention also provides stretchable semiconductor structures and stretchable electronic devices capable of good performance in stretched configurations.

Methods and devices for fabricating and assembling printable semiconductor elements

DOEpatents

Nuzzo, Ralph G; Rogers, John A; Menard, Etienne; Lee, Keon Jae; Khang, Dahl-Young; Sun, Yugang; Meitl, Matthew; Zhu, Zhengtao

2014-03-04

The invention provides methods and devices for fabricating printable semiconductor elements and assembling printable semiconductor elements onto substrate surfaces. Methods, devices and device components of the present invention are capable of generating a wide range of flexible electronic and optoelectronic devices and arrays of devices on substrates comprising polymeric materials. The present invention also provides stretchable semiconductor structures and stretchable electronic devices capable of good performance in stretched configurations.

Medical Devices; General Hospital and Personal Use Devices; Classification of the Ultraviolet Radiation Chamber Disinfection Device. Final order.

PubMed

2015-11-20

The Food and Drug Administration (FDA or the Agency) is classifying the ultraviolet (UV) radiation chamber disinfection device into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the UV radiation chamber disinfection device classification. The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device.

The Importance of State and Context in Safe Interoperable Medical Systems

PubMed Central

Jaffe, Michael B.; Robkin, Michael; Rausch, Tracy; Arney, David; Goldman, Julian M.

2016-01-01

This paper describes why “device state” and “patient context” information are necessary components of device models for safe interoperability. This paper includes a discussion of the importance of describing the roles of devices with respect to interactions (including human user workflows involving devices, and device to device communication) within a system, particularly those intended for use at the point-of-care, and how this role information is communicated. In addition, it describes the importance of clinical scenarios in creating device models for interoperable devices. PMID:27730013

Policy-based secure communication with automatic key management for industrial control and automation systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chernoguzov, Alexander; Markham, Thomas R.; Haridas, Harshal S.

A method includes generating at least one access vector associated with a specified device in an industrial process control and automation system. The specified device has one of multiple device roles. The at least one access vector is generated based on one or more communication policies defining communications between one or more pairs of devices roles in the industrial process control and automation system, where each pair of device roles includes the device role of the specified device. The method also includes providing the at least one access vector to at least one of the specified device and one ormore » more other devices in the industrial process control and automation system in order to control communications to or from the specified device.« less

Progress and Prospects in Stretchable Electroluminescent Devices

NASA Astrophysics Data System (ADS)

Wang, Jiangxin; Lee, Pooi See

2017-03-01

Stretchable electroluminescent (EL) devices are a new form of mechanically deformable electronics that are gaining increasing interests and believed to be one of the essential technologies for next generation lighting and display applications. Apart from the simple bending capability in flexible EL devices, the stretchable EL devices are required to withstand larger mechanical deformations and accommodate stretching strain beyond 10%. The excellent mechanical conformability in these devices enables their applications in rigorous mechanical conditions such as flexing, twisting, stretching, and folding.The stretchable EL devices can be conformably wrapped onto arbitrary curvilinear surface and respond seamlessly to the external or internal forces, leading to unprecedented applications that cannot be addressed with conventional technologies. For example, they are in demand for wide applications in biomedical-related devices or sensors and soft interactive display systems, including activating devices for photosensitive drug, imaging apparatus for internal tissues, electronic skins, interactive input and output devices, robotics, and volumetric displays. With increasingly stringent demand on the mechanical requirements, the fabrication of stretchable EL device is encountering many challenges that are difficult to resolve. In this review, recent progresses in the stretchable EL devices are covered with a focus on the approaches that are adopted to tackle materials and process challenges in stretchable EL devices and delineate the strategies in stretchable electronics. We first introduce the emission mechanisms that have been successfully demonstrated on stretchable EL devices. Limitations and advantages of the different mechanisms for stretchable EL devices are also discussed. Representative reports are reviewed based on different structural and material strategies. Unprecedented applications that have been enabled by the stretchable EL devices are reviewed. Finally, we summarize with our perspectives on the approaches for the stretchable EL devices and our proposals on the future development in these devices.

Multiple constraints compromise decision-making about implantable medical devices for individual patients: qualitative interviews with physicians.

PubMed

Gagliardi, Anna R; Ducey, Ariel; Lehoux, Pascale; Turgeon, Thomas; Kolbunik, Jeremy; Ross, Sue; Trbovich, Patricia; Easty, Anthony; Bell, Chaim; Urbach, David R

2017-12-22

Little research has examined how physicians choose medical devices for treating individual patients to reveal if interventions are needed to support decision-making and reduce device-associated morbidity and mortality. This study explored factors that influence choice of implantable device from among available options. A descriptive qualitative approach was used. Physicians who implant orthopedic and cardiovascular devices were identified in publicly available directories and web sites. They were asked how they decided what device to use in a given patient, sources of information they consulted, and how patients were engaged in decision-making. Sampling was concurrent with data collection and analysis to achieve thematic saturation. Data were analyzed using constant comparative technique by all members of the research team. Twenty-two physicians from five Canadian provinces (10 cardiovascular, 12 orthopedic; 8, 10 and 4 early, mid and late career, respectively) were interviewed. Responses did not differ by specialty, geographic region or career stage. Five major categories of themes emerged that all influence decision-making about a range of devices, and often compromise choice of the most suitable device for a given patient, potentially leading to sub-optimal clinical outcomes: lack of evidence on device performance, patient factors, physician factors, organizational and health system factors, and device and device market factors. In the absence of evidence from research or device registries, tacit knowledge from trusted colleagues and less-trusted industry representatives informed device choice. Patients were rarely engaged in decision-making. Physician preference for particular devices was a barrier to acquiring competency in devices potentially more suitable for patients. Access to suitable devices was further limited to the number of comparable devices on the market, local inventory and purchasing contract specifications. This study revealed that decision-making about devices is complex, cognitively challenging and constrained by several factors limiting access to and use of devices that could optimize patient outcomes. Further research is needed to assess the impact of these constraints on clinical outcomes, and develop interventions that optimize decision-making about device choice for treating given patients.

[Comparative study of device labeling regulation in U.S.A. and China].

PubMed

Li, Fei; Wei, Jing; Ma, Yanbin; Li, Zhu

2010-09-01

To provide references for the evolvement of medical devices labeling and manual administration in China, By content analysis, 10 juristic documents relevant to device labeling and manual were collected from FDA website, compared to which, the federal regulation was mainly analyzed. There are five main differences of device labeling regulation between U.S.A. and China: juristic system, administrative scope, administrative target, characteristics and practice, A set of comprehensive juristic system for device labeling has been established by FDA. from which China should draw experience, to administrate the prescription devices and the over-the-counter devices in classification, and set up device labeling guidance, thus guarantee the safety and efficacy of device.

Surface Acoustic Wave Monitor for Deposition and Analysis of Ultra-Thin Films

NASA Technical Reports Server (NTRS)

Hines, Jacqueline H. (Inventor)

2015-01-01

A surface acoustic wave (SAW) based thin film deposition monitor device and system for monitoring the deposition of ultra-thin films and nanomaterials and the analysis thereof is characterized by acoustic wave device embodiments that include differential delay line device designs, and which can optionally have integral reference devices fabricated on the same substrate as the sensing device, or on a separate device in thermal contact with the film monitoring/analysis device, in order to provide inherently temperature compensated measurements. These deposition monitor and analysis devices can include inherent temperature compensation, higher sensitivity to surface interactions than quartz crystal microbalance (QCM) devices, and the ability to operate at extreme temperatures.

21 CFR 872.1745 - Laser fluorescence caries detection device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1745 Laser fluorescence caries... fluorescence detector housed in a dental handpiece, and a control console that performs device calibration, as...

21 CFR 872.1745 - Laser fluorescence caries detection device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... SERVICES (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1745 Laser fluorescence caries... fluorescence detector housed in a dental handpiece, and a control console that performs device calibration, as...

76 FR 48871 - Immunology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-09

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0002] Immunology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Immunology Devices Panel of the Medical Devices Advisory Committee. General Function of the Committee: To...

76 FR 55398 - Immunology Devices Panel of the Medical Devices Advisory Committee: Notice of Postponement of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-07

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0002] Immunology Devices Panel of the Medical Devices Advisory Committee: Notice of Postponement of Meeting AGENCY... postponing the meeting of the Immunology Devices Panel of the Medical Devices Advisory Committee scheduled...

76 FR 6625 - Neurological Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-07

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2011-N-0002] Neurological Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Neurological Devices Panel of the Medical Devices Advisory Committee. General Function of the Committee: To...

76 FR 12973 - Neurological Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-09

...] Neurological Devices Panel of the Medical Devices Advisory Committee; Amendment of Notice AGENCY: Food and Drug... notice of meeting of the Neurological Devices Panel of the Medical Devices Advisory Committee. This... INFORMATION: In the Federal Register of February 7, 2011, FDA announced that a meeting of the Neurological...

76 FR 36548 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-22

...] Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and... of Committee: Circulatory System Devices Panel of the Medical Devices Advisory Committee. General... also comes with a sheath, introducer, loader, dilator, balloon (used to pre-dilate the native annulus...

77 FR 25183 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-27

...] Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and... of Committee: Circulatory System Devices Panel of the Medical Devices Advisory Committee. General..., introducer, loader, dilator, balloon (used to pre-dilate the native annulus) and a crimper. FDA intends to...

78 FR 26786 - Microbiology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-08

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0001] Microbiology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and Drug...: Microbiology Devices Panel of the Medical Devices Advisory Committee. General Function of the Committee: To...

76 FR 69034 - Microbiology Devices; Classification of In Vitro Diagnostic Device for Yersinia Species Detection

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-07

... Drug Administration 21 CFR Part 866 Microbiology Devices; Classification of In Vitro Diagnostic Device... CFR Part 866 [Docket No. FDA-2011-N-0729] Microbiology Devices; Classification of In Vitro Diagnostic... of the Microbiology Devices Advisory Panel (the panel). FDA is publishing in this document the...

75 FR 57968 - Gastroenterology and Urology Devices Panel of the Medical Devices Advisory Committee; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-23

...] Gastroenterology and Urology Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY... public. Name of Committee: Gastroenterology and Urology Devices Panel of the Medical Devices Advisory... committee will discuss, make recommendations, and vote on information related to the PMA for the LAP-BAND...

76 FR 54156 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-31

... traffic control device design, location, or operation that have made some existing devices in the field...-2010-0159] RIN 2125-AF43 National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for Streets and Highways; Revision AGENCY: Federal Highway Administration (FHWA...

21 CFR 868.5115 - Device to relieve acute upper airway obstruction.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Device to relieve acute upper airway obstruction. 868.5115 Section 868.5115 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5115 Device to...

21 CFR 868.5115 - Device to relieve acute upper airway obstruction.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Device to relieve acute upper airway obstruction. 868.5115 Section 868.5115 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5115 Device to...

21 CFR 868.5115 - Device to relieve acute upper airway obstruction.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Device to relieve acute upper airway obstruction. 868.5115 Section 868.5115 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5115 Device to...

14 CFR 23.373 - Speed control devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Speed control devices. 23.373 Section 23....373 Speed control devices. If speed control devices (such as spoilers and drag flaps) are incorporated....441 and 23.443, with the device extended at speeds up to the placard device extended speed; and (b) If...

14 CFR 23.373 - Speed control devices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Speed control devices. 23.373 Section 23....373 Speed control devices. If speed control devices (such as spoilers and drag flaps) are incorporated....441 and 23.443, with the device extended at speeds up to the placard device extended speed; and (b) If...

75 FR 47606 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-06

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of... General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee scheduled for August...

78 FR 30928 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-23

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting... the public. Name of Committee: General and Plastic Surgery Devices Panel of the Medical Devices...

75 FR 49940 - General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-16

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2010-N-0001] General and Plastic Surgery Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting... the public. Name of Committee: General and Plastic Surgery Devices Panel of the Medical Devices...

21 CFR 830.300 - Devices subject to device identification data submission requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Devices subject to device identification data submission requirements. 830.300 Section 830.300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... Identification Database § 830.300 Devices subject to device identification data submission requirements. (a) In...

21 CFR 880.6785 - Manual patient transfer device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Miscellaneous Devices § 880.6785 Manual patient transfer device. (a) Identification. A manual patient transfer device is a device consisting of a wheeled stretcher and a mechanism on which a patient can be placed so... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Manual patient transfer device. 880.6785 Section...

The Need to Apply Medical Device Informatics in Developing Standards for Safe Interoperable Medical Systems.

PubMed

Weininger, Sandy; Jaffe, Michael B; Goldman, Julian M

2017-01-01

Medical device and health information technology systems are increasingly interdependent with users demanding increased interoperability. Related safety standards must be developed taking into account these systems' perspective. In this article, we describe the current development of medical device standards and the need for these standards to address medical device informatics. Medical device information should be gathered from a broad range of clinical scenarios to lay the foundation for safe medical device interoperability. Five clinical examples show how medical device informatics principles, if applied in the development of medical device standards, could help facilitate the development of safe interoperable medical device systems. These examples illustrate the clinical implications of the failure to capture important signals and device attributes. We provide recommendations relating to the coordination between historically separate standards development groups, some of which focus on safety and effectiveness and others focus on health informatics. We identify the need for a shared understanding among stakeholders and describe organizational structures to promote cooperation such that device-to-device interactions and related safety information are considered during standards development.

The Need to Apply Medical Device Informatics in Developing Standards for Safe Interoperable Medical Systems

PubMed Central

Weininger, Sandy; Jaffe, Michael B.; Goldman, Julian M

2016-01-01

Medical device and health information technology systems are increasingly interdependent with users demanding increased interoperability. Related safety standards must be developed taking into account this systems perspective. In this article we describe the current development of medical device standards and the need for these standards to address medical device informatics. Medical device information should be gathered from a broad range of clinical scenarios to lay the foundation for safe medical device interoperability. Five clinical examples show how medical device informatics principles, if applied in the development of medical device standards, could help facilitate the development of safe interoperable medical device systems. These examples illustrate the clinical implications of the failure to capture important signals and device attributes. We provide recommendations relating to the coordination between historically separate standards development groups; some which focus on safety and effectiveness, and others that focus on health informatics. We identify the need for a shared understanding among stakeholders and describe organizational structures to promote cooperation such that device-to-device interactions and related safety information are considered during standards development. PMID:27584685

Regulatory science based approach in development of novel medical devices.

PubMed

Sakuma, Ichiro

2015-08-01

For development rational evaluation method for medical devices' safety and efficacy, regulatory science studies are important. Studies on regulatory affairs related to a medical device under development should be conducted as well as its technological development. Clinical performance of a medical device is influenced by performance of the device, medical doctors' skill, pathological condition of a patient, and so on. Thus it is sometimes difficult to demonstrate superiority of the device in terms of clinical outcome although its efficacy as a medical device is accepted. Setting of appropriate end points is required to evaluate a medical device appropriately. Risk assessment and risk management are the basis of medical device safety assurance. In case of medical device software, there are difficulties in identifying the risk due to its complexity of user environment and different design and manufacturing procedure compared with conventional hardware based medical devices. Recent technological advancement such as information and communication technologies (ICT) for medical devices and wireless network has raised new issue on risk management: cybersecurity. We have to watch closely the progress of safety standard development.

Implantation reduces the negative effects of bio-logging devices on birds.

PubMed

White, Craig R; Cassey, Phillip; Schimpf, Natalie G; Halsey, Lewis G; Green, Jonathan A; Portugal, Steven J

2013-02-15

Animal-borne logging or telemetry devices are widely used for measurements of physiological and movement data from free-living animals. For such measurements to be relevant, however, it is essential that the devices themselves do not affect the data of interest. A recent meta-analysis reported an overall negative effect of these devices on the birds that bear them, i.e. on nesting productivity, clutch size, nest initiation date, offspring quality, body condition, flying ability, foraging behaviours, energy expenditure and survival rate. Method of attachment (harness, collar, glue, anchor, implant, breast-mounted or tailmount) had no influence on the strength of these effects but anchored and implanted transmitters had the highest reported rates of device-induced mortality. Furthermore, external devices, but not internal devices, caused an increase in 'device-induced behaviour' (comfort behaviours such as preening, fluffing and stretching, and unrest activities including unquantifiable 'active' behaviours). These findings suggest that, with the exception of device-induced behaviour, external attachment is preferable to implantation. In the present study we undertake a meta-analysis of 183 estimates of device impact from 39 studies of 36 species of bird designed to explicitly compare the effects of externally attached and surgically implanted devices on a range of traits, including condition, energy expenditure and reproduction. In contrast to a previous study, we demonstrate that externally attached devices have a consistent detrimental effect (i.e. negative influences on body condition, reproduction, metabolism and survival), whereas implanted devices have no consistent effect. We also show that the magnitude of the negative effect of externally attached devices decreases with time. We therefore conclude that device implantation is preferable to external attachment, providing that the risk of mortality associated with the anaesthesia and surgery required for implantation can be mitigated. We recommend that studies employing external devices use devices that can be borne for long periods, and, wherever possible, deploy devices in advance of the time period of interest.

Adolescents' Use of Basic, Intermediate, and Advanced Device Types for Vaping.

PubMed

Pepper, Jessica K; MacMonegle, Anna J; Nonnemaker, James M

2017-12-23

Advanced models of electronic vaping products (EVPs) likely pose a greater risk to adolescent health than basic or intermediate models because advanced models deliver nicotine more effectively and heat e-liquid to higher temperatures, producing more harmful chemical emissions. However, little is known about adolescents' risk factors for using different device types. We used social media to recruit an online sample of 1,508 U.S. adolescents aged 15-17 who reported past 30-day use of e-cigarettes. We assessed tobacco use, beliefs and knowledge about EVPs, and EVP use behavior, including the device type participants use most frequently. We used multinomial logistic regression to examine differences between adolescents who usually use intermediate versus basic and advanced versus basic devices. Most respondents usually used modifiable advanced devices (56.8%) rather than basic "cigalike" (14.5%) or pen-style intermediate (28.7%) devices. Use of multiple device types was common, particularly among those who primarily used basic devices. Younger age and less frequent vaping were associated with mainly using basic devices. Adolescents who were older, male, personally bought their main device, and had ever mixed e-liquids were at elevated risk for usually using advanced devices. Adolescents who primarily use basic devices may be newer users who are experimenting with multiple devices. Future research should examine which adolescents are most likely to transition to advanced devices in order to develop targeted interventions. Regulators should consider strategies to reduce access to all types of EVPs, such as better enforcement of the current ban on sales to minors. This research addresses two gaps in research on adolescent electronic vaping product use: (1) characterizing use of advanced devices as distinct from intermediate devices rather than grouping them together and (2) examining factors associated with use of specific device types. This study suggests that there are distinct profiles of adolescents who use primarily basic, intermediate, or advanced devices. Adolescents who most often use basic devices may be new users experimenting with vaping, whereas adolescents who most often use advanced devices appear to be buying devices for themselves and engaging in risky behaviors such as mixing their own e-liquid. © The Author(s) 2017. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Fabrication of a microfluidic device for the compartmentalization of neuron soma and axons.

PubMed

Harris, Joseph; Lee, Hyuna; Vahidi, Behrad; Tu, Christina; Cribbs, David; Jeon, Noo Li; Cotman, Carl

2007-01-01

In this video, we demonstrate the technique of soft lithography with polydimethyl siloxane (PDMS) which we use to fabricate a microfluidic device for culturing neurons. Previously, a silicon wafer was patterned with the design for the neuron microfluidic device using SU-8 and photolithography to create a master mold, or what we simply refer to as a "master". Next, we pour the silicon polymer PDMS on top of the master which is then cured by heating the PDMS to 80 degrees C for 1 hour. The PDMS forms a negative mold of the device. The PDMS is then carefully cut and lifted away from the master. Holes are punched where the reservoirs will be and the excess PDMS trimmed away from the device. Nitrogen is used to blow away any excess debris from the device. At this point the devices are now ready for use and can either bonded to corning No. 1 cover glass with a plasma sterilizer/cleaner or can be reversibly bound to the cover glass by simply placing the device on top of the cover glass. The reversible bonding of the device to glass is covered in a separate video and requires first that the device be sterilized either with 70% ethanol or by autoclaving. Plasma treating sterilizes the devices so no further treatment is necessary. It is, however, important, when plasma-treating the devices, to add liquid to the devices within 10 minutes of the plasma treatment while the surfaces are still hydrophilic. Waiting longer than 10 minutes to add liquid to the device makes it difficult for the liquid to enter the device. The neuron devices are typically plasma-bound to cover glass and 0.5 mg/ml poly-L-lysine (PLL) in pH 8.5 borate buffer is immediately added to the device. After a minimum of 3 hours incubating with PLL, the devices are washed with dH2O water a minimum of 3 times with at least 15 minutes between each wash. Next, the water is removed and fresh media is added to the device. At this point the device is ready for use. It is important to remember at this point to never remove all the media from the device. Always leave media in the main channel.

[Industry regulation and its relationship to the rapid marketing of medical devices].

PubMed

Matsuoka, Atsuko

2012-01-01

In the market of medical devices, non-Japanese products hold a large part even in Japan. To overcome this situation, the Japanese government has been announcing policies to encourage the medical devices industry, such as the 5-year strategy for medical innovation (June 6, 2012). The Division of Medical Devices has been contributing to rapid marketing of medical devices by working out the standards for approval review and accreditation of medical devices, guidances on evaluation of medical devices with emerging technology, and test methods for biological safety evaluation of medical devices, as a part of practice in the field of regulatory science. The recent outcomes are 822 standards of accreditation for Class II medical devices, 14 guidances on safety evaluation of medical devices with emerging technology, and the revised test methods for biological safety evaluation (MHLW Notification by Director, OMDE, Yakushokuki-hatsu 0301 No. 20 "Basic Principles of Biological Safety Evaluation Required for Application for Approval to Market Medical Devices").

An Integrated Device View on Photo-Electrochemical Solar-Hydrogen Generation.

PubMed

Modestino, Miguel A; Haussener, Sophia

2015-01-01

Devices that directly capture and store solar energy have the potential to significantly increase the share of energy from intermittent renewable sources. Photo-electrochemical solar-hydrogen generators could become an important contributor, as these devices can convert solar energy into fuels that can be used throughout all sectors of energy. Rather than focusing on scientific achievement on the component level, this article reviews aspects of overall component integration in photo-electrochemical water-splitting devices that ultimately can lead to deployable devices. Throughout the article, three generalized categories of devices are considered with different levels of integration and spanning the range of complete integration by one-material photo-electrochemical approaches to complete decoupling by photovoltaics and electrolyzer devices. By using this generalized framework, we describe the physical aspects, device requirements, and practical implications involved with developing practical photo-electrochemical water-splitting devices. Aspects reviewed include macroscopic coupled multiphysics device models, physical device demonstrations, and economic and life cycle assessments, providing the grounds to draw conclusions on the overall technological outlook.

Development of reversible vas deferens occlusive device: IV. Rigid prosthetic devices.

PubMed

Drueschke, E E; Zaneveld, L J; Burns, M; Rodzen, R; Wingfield, J R; Maness, J H

1975-01-01

Different types of rigid, reversible, vas deferens occlusive devices were developed and evaluated in 14 unilaterally vasectomized dogs. All prosthetic devices had molded silicone rubber bodies, and rigid inflow and outflow tubes. Various techniques for the removal of the vas luminal epithelium, and for the preparation of porous ceramic and etched stainless steel surfaces to encourage tissue ingrowth into the prosthetic device end tubues were attempted. The devices differed in their methods of achieving occlusion. One device used a "rotary stem valve" which had a C-section rotating mechanism; the others used the "shuttle stem valve" which possessed an occlusive element that moved transverse to the axis of flow in the device, thus occluding the device when the stem was depressed. The rotarystem valve was implanted by means of a longitudinal incision. The remaining 13 shuttle stem devices were placed in the vas using either a longitudinal or a transverse implantation. Inno case was sperm transport through the prosthetic devices obtained for more than a few ejaculations.

[Status of diagnosis and treatment devices of acupuncture based on SooPAT and bibliometrics in China].

PubMed

Bai, Lin; Ren, Yulan; Guo, Taipin; Chen, Lin; Zhou, Yumei; Feng, Shuwei; Li, Ji; Liang, Fanrong

2016-11-12

To perform a bibliometrics analysis on patent literature regarding diagnosis and treatment devices of acupuncture in China, aiming to provide references for the development of diagnosis and treatment devices of acupuncture. Based on SooPAT, a patent database, the patent literature regarding diagnosis and treatment devices of acupuncture in China was collected. With bibliometrics methods, the annual distribution of type, quantity, classification and content of diagnosis and treatment devices of acupuncture were analyzed. The number of acupuncture diagnosis and treatment devices reached its peak in 2012 and 2013 in China. The A61N in patent and utility model patent were the most, which were mainly related to electrotherapy, magnetic therapy, radioactive therapy and ultrasound therapy, etc. The main content was acupuncture treatment devices and meridian treatment devices. The 24-01 in design patent was the most, involving fixation devices used by doctors, hospitals and laboratories, etc. Currently the majority of diagnosis and treatment devices of acupuncture is therapeutic apparatus, while the acupuncture diagnosis devices are needed.

Technology assessment of medical devices at the Center for Devices and Radiological Health.

PubMed

Kessler, L; Richter, K

1998-09-25

We reviewed the Food and Drug Administration's regulatory process for medical devices and described the issues that arise in assessing device safety and effectiveness during the postmarket period. The Center for Devices and Radiological Health (CDRH), an organization within the Food and Drug Administration, has the legal authority and responsibility for ensuring that medical devices marketed in the United States are both reasonably safe and effective for their intended use. This is an enormous challenge given the diversity of medical devices and the large number of different types of devices on the market. Many scientific and regulatory activities are necessary to ensure device safety and effectiveness, including technology assessment, albeit in a manner quite different from that of conventional technology assessment. The basic approach taken at the CDRH to ensure device safety and effectiveness is to develop an understanding of the way in which a medical device works and how it will perform in clinical situations.

Power spectrum analysis for defect screening in integrated circuit devices

DOEpatents

Tangyunyong, Paiboon; Cole Jr., Edward I.; Stein, David J.

2011-12-01

A device sample is screened for defects using its power spectrum in response to a dynamic stimulus. The device sample receives a time-varying electrical signal. The power spectrum of the device sample is measured at one of the pins of the device sample. A defect in the device sample can be identified based on results of comparing the power spectrum with one or more power spectra of the device that have a known defect status.

Cooling of superconducting devices by liquid storage and refrigeration unit

DOEpatents

Laskaris, Evangelos Trifon; Urbahn, John Arthur; Steinbach, Albert Eugene

2013-08-20

A system is disclosed for cooling superconducting devices. The system includes a cryogen cooling system configured to be coupled to the superconducting device and to supply cryogen to the device. The system also includes a cryogen storage system configured to supply cryogen to the device. The system further includes flow control valving configured to selectively isolate the cryogen cooling system from the device, thereby directing a flow of cryogen to the device from the cryogen storage system.

21 CFR 806.20 - Records of corrections and removals not required to be reported.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES MEDICAL DEVICES; REPORTS OF CORRECTIONS AND... known, and the intended use of the device. (2) The model, catalog, or code number of the device and the...) Each device manufacturer or importer who initiates a correction or removal of a device that is not...

21 CFR 803.32 - If I am a user facility, what information must I submit in my individual adverse event reports?

Code of Federal Regulations, 2011 CFR

2011-04-01

... ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES MEDICAL DEVICE REPORTING User... device; (10) Event problem codes—patient code and device code (refer to the “MEDWATCH Medical Device... device was involved, nature of the problem, patient followup or required treatment, and any environmental...

21 CFR 803.32 - If I am a user facility, what information must I submit in my individual adverse event reports?

Code of Federal Regulations, 2010 CFR

2010-04-01

... ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES MEDICAL DEVICE REPORTING User... device; (10) Event problem codes—patient code and device code (refer to the “MEDWATCH Medical Device... device was involved, nature of the problem, patient followup or required treatment, and any environmental...

21 CFR 806.20 - Records of corrections and removals not required to be reported.

Code of Federal Regulations, 2010 CFR

2010-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES MEDICAL DEVICES; REPORTS OF CORRECTIONS AND... known, and the intended use of the device. (2) The model, catalog, or code number of the device and the...) Each device manufacturer or importer who initiates a correction or removal of a device that is not...

Pipe inspection and repair system

NASA Technical Reports Server (NTRS)

Schempf, Hagen (Inventor); Mutschler, Edward (Inventor); Chemel, Brian (Inventor); Boehmke, Scott (Inventor); Crowley, William (Inventor)

2004-01-01

A multi-module pipe inspection and repair device. The device includes a base module, a camera module, a sensor module, an MFL module, a brush module, a patch set/test module, and a marker module. Each of the modules may be interconnected to construct one of an inspection device, a preparation device, a marking device, and a repair device.

An UV photochromic memory effect in proton-based WO3 electrochromic devices

NASA Astrophysics Data System (ADS)

Zhang, Yong; Lee, S.-H.; Mascarenhas, A.; Deb, S. K.

2008-11-01

We report an UV photochromic memory effect on a standard proton-based WO3 electrochromic device. It exhibits two memory states, associated with the colored and bleached states of the device, respectively. Such an effect can be used to enhance device performance (increasing the dynamic range), re-energize commercial electrochromic devices, and develop memory devices.

78 FR 11612 - Medical Devices; Pediatric Uses of Devices; Requirement for Submission of Information on...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-19

... information that will have been reviewed by the applicant during the course of its development of the device..., infants, children, adolescents) that suffer from the disease or condition that the device is intended to.... FDA-2009-N-0458] RIN 0910-AG29 Medical Devices; Pediatric Uses of Devices; Requirement for Submission...

Medical Devices; General Hospital and Personal Use Devices; Classification of the Image Processing Device for Estimation of External Blood Loss. Final order.

PubMed

2017-12-20

The Food and Drug Administration (FDA or we) is classifying the image processing device for estimation of external blood loss into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the image processing device for estimation of external blood loss' classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

Method for triggering an action

DOEpatents

Hall, David R.; Bartholomew, David B.; Johnson, Monte L.; Moon, Justin; Koehler, Roger O.

2006-10-17

A method for triggering an action of at least one downhole device on a downhole network integrated into a downhole tool string synchronized to an event comprises determining latency, sending a latency adjusted signal, and performing the action. The latency is determined between a control device and the at least one downhole device. The latency adjusted signal for triggering an action is sent to the downhole device. The action is performed downhole synchronized to the event. A preferred method for determining latency comprises the steps: a control device sends a first signal to the downhole device; after receiving the signal, the downhole device sends a response signal to the control device; and the control device analyzes the time from sending the signal to receiving the response signal.

Radiofrequency ablation for hepatocellular carcinoma: a prospective comparison of four radiofrequency devices.

PubMed

Lin, Shi-Ming; Lin, Chen-Chun; Chen, Wei-Ting; Chen, Yi-Chen; Hsu, Chao-Wei

2007-09-01

To compare the effectiveness of ablation techniques for hepatocellular carcinoma (HCC) with the use of four radiofrequency (RF) devices. One hundred patients with 133 HCC lesions no larger than 4 cm were treated with one of four RF devices: RF 2000 (maximum power, 100 W) and RF 3000 generators (maximum power, 200 W) with LeVeen expandable electrodes with a maximum dimension of 3.5 cm or 4 cm, internally cooled single electrode with a thermal dimension of 3 cm, and a RITA RF generator with expandable electrodes with a maximum dimension of 5 cm. Numbers of RF sessions needed per HCC to achieve complete necrosis were 1.4 +/- 0.5 with the RF 2000 device and greater than 1.1 +/- 0.3 with the other three devices (P < .05). The RF 2000 device required a more interactive algorithm than the RF 3000 device. Session times per patient were 31.7 minutes +/- 13.2 in the RF 2000 group and longer than 16.6 minutes +/- 7.5 in the RF 3000 group, 28.3 minutes +/- 12 in the RITA device group, and 27.1 minutes +/- 12 with the internally cooled electrode device (P < .005 for RF 2000 vs other devices and for RF 3000 vs RITA or internally cooled electrode device). Complete necrosis and local tumor progression rates at 2 years in the RF 2000, RF 3000, RITA, and internally cooled electrode device groups were 91.1%, 97.1%, 96.7%, and 96.8% and 12%, 8%, 8.2%, and 8.3%, respectively (P = .37). Ablation with the RF 3000 device required a shorter time than the other three devices and required a less interactive algorithm than the RF 2000 device. However, complete necrosis and local tumor progression rates were similar among devices.

FDA's perspectives on cardiovascular devices.

PubMed

Chen, Eric A; Patel-Raman, Sonna M; O'Callaghan, Kathryn; Hillebrenner, Matthew G

2009-06-01

The Food and Drug Administration (FDA) decision process for approving or clearing medical devices is often determined by a review of robust clinical data and extensive preclinical testing of the device. The mission statement for the Center for Devices and Radiological Health (CDRH) is to review the information provided by manufacturers so that it can promote and protect the health of the public by ensuring the safety and effectiveness of medical devices deemed appropriate for human use (Food, Drug & Cosmetic Act, Section 903(b)(1, 2(C)), December 31, 2004; accessed December 17, 2008 http://www.fda.gov/opacom/laws/fdcact/fdctoc.htm). For high-risk devices, such as ventricular assist devices (VADs), mechanical heart valves, stents, cardiac resynchronization therapy (CRT) devices, pacemakers, and defibrillators, the determination is based on FDA's review of extensive preclinical bench and animal testing followed by use of the device in a clinical trial in humans. These clinical trials allow the manufacturer to evaluate a device in the intended use population. FDA reviews the data from the clinical trial to determine if the device performed as predicted and the clinical benefits outweigh the risks. This article reviews the regulatory framework for different marketing applications related to cardiovascular devices and describes the process of obtaining approval to study a cardiovascular device in a U.S. clinical trial.

Materials for electrochemical device safety

DOEpatents

Vissers, Daniel R.; Amine, Khalil; Thackeray, Michael M.; Kahaian, Arthur J.; Johnson, Christopher S.

2015-04-07

An electrochemical device includes a thermally-triggered intumescent material or a gas-triggered intumescent material. Such devices prevent or minimize short circuits in a device that could lead to thermal run-away. Such devices may include batteries or supercapacitors.

Illusion thermal device based on material with constant anisotropic thermal conductivity for location camouflage

NASA Astrophysics Data System (ADS)

Hou, Quanwen; Zhao, Xiaopeng; Meng, Tong; Liu, Cunliang

2016-09-01

Thermal metamaterials and devices based on transformation thermodynamics often require materials with anisotropic and inhomogeneous thermal conductivities. In this study, still based on the concept of transformation thermodynamics, we designed a planar illusion thermal device, which can delocalize a heat source in the device such that the temperature profile outside the device appears to be produced by a virtual source at another position. This device can be constructed by only one kind of material with constant anisotropic thermal conductivity. The condition which should be satisfied by the device is provided, and the required anisotropic thermal conductivity is then deduced theoretically. This study may be useful for the designs of metamaterials or devices since materials with constant anisotropic parameters have great facility in fabrication. A prototype device has been fabricated based on a composite composed by two naturally occurring materials. The experimental results validate the effectiveness of the device.

Flexible devices: from materials, architectures to applications

NASA Astrophysics Data System (ADS)

Zou, Mingzhi; Ma, Yue; Yuan, Xin; Hu, Yi; Liu, Jie; Jin, Zhong

2018-01-01

Flexible devices, such as flexible electronic devices and flexible energy storage devices, have attracted a significant amount of attention in recent years for their potential applications in modern human lives. The development of flexible devices is moving forward rapidly, as the innovation of methods and manufacturing processes has greatly encouraged the research of flexible devices. This review focuses on advanced materials, architecture designs and abundant applications of flexible devices, and discusses the problems and challenges in current situations of flexible devices. We summarize the discovery of novel materials and the design of new architectures for improving the performance of flexible devices. Finally, we introduce the applications of flexible devices as key components in real life. Project supported by the National Key R&D Program of China (Nos. 2017YFA0208200, 2016YFB0700600, 2015CB659300), the National Natural Science Foundation of China (Nos. 21403105, 21573108), and the Fundamental Research Funds for the Central Universities (No. 020514380107).

The FDA's role in medical device clinical studies of human subjects

NASA Astrophysics Data System (ADS)

Saviola, James

2005-03-01

This paper provides an overview of the United States Food and Drug Administration's (FDA) role as a regulatory agency in medical device clinical studies involving human subjects. The FDA's regulations and responsibilities are explained and the device application process discussed. The specific medical device regulatory authorities are described as they apply to the development and clinical study of retinal visual prosthetic devices. The FDA medical device regulations regarding clinical studies of human subjects are intended to safeguard the rights and safety of subjects. The data gathered in pre-approval clinical studies provide a basis of valid scientific evidence in order to demonstrate the safety and effectiveness of a medical device. The importance of a working understanding of applicable medical device regulations from the beginning of the device development project is emphasized particularly for novel, complex products such as implantable visual prosthetic devices.

Method and system for reducing device performance degradation of organic devices

DOEpatents

Teague, Lucile C.

2014-09-02

Methods and systems for reducing the deleterious effects of gate bias stress on the drain current of an organic device, such as an organic thin film transistor, are provided. In a particular aspect, the organic layer of an organic device is illuminated with light having characteristics selected to reduce the gate bias voltage effects on the drain current of the organic device. For instance, the wavelength and intensity of the light are selected to provide a desired recovery of drain current of the organic device. If the characteristics of the light are appropriately matched to the organic device, recovery of the deleterious effects caused by gate bias voltage stress effects on the drain current of the organic device can be achieved. In a particular aspect, the organic device is selectively illuminated with light to operate the organic device in multiple modes of operation.

Non- contacting capacitive diagnostic device

DOEpatents

Ellison, Timothy

2005-07-12

A non-contacting capacitive diagnostic device includes a pulsed light source for producing an electric field in a semiconductor or photovoltaic device or material to be evaluated and a circuit responsive to the electric field. The circuit is not in physical contact with the device or material being evaluated and produces an electrical signal characteristic of the electric field produced in the device or material. The diagnostic device permits quality control and evaluation of semiconductor or photovoltaic device properties in continuous manufacturing processes.

Method for integrating microelectromechanical devices with electronic circuitry

DOEpatents

Montague, Stephen; Smith, James H.; Sniegowski, Jeffry J.; McWhorter, Paul J.

1998-01-01

A method for integrating one or more microelectromechanical (MEM) devices with electronic circuitry. The method comprises the steps of forming each MEM device within a cavity below a device surface of the substrate; encapsulating the MEM device prior to forming electronic circuitry on the substrate; and releasing the MEM device for operation after fabrication of the electronic circuitry. Planarization of the encapsulated MEM device prior to formation of the electronic circuitry allows the use of standard processing steps for fabrication of the electronic circuitry.

Update on Tissue Tightening

PubMed Central

2010-01-01

A variety of medical devices are described under the heading of tissue tightening devices. This article reviews the tissue tightening devices currently available in the United States and some that may receive clearance in the upcoming year. These include the various radiofrequency devices as well as the pulsed light devices that achieve similar end results. The one noticeable factor seen with this group of devices is the paucity of large, clinical, controlled trials that appear in the medical literature for this group of medical devices as a whole. PMID:20725568

Perceptions of healthcare professionals' support, shock anxiety and device acceptance among implantable cardioverter defibrillator recipients.

PubMed

Morken, Ingvild M; Norekvål, Tone M; Bru, Edvin; Larsen, Alf I; Karlsen, Bjørg

2014-09-01

To investigate the extent to which perceived support from healthcare professionals and shock anxiety is related to device acceptance among implantable cardioverter defibrillator recipients. Device acceptance can be influenced by several factors, one of which is shock anxiety associated with poor device acceptance. Reduced shock anxiety, as well as increased device acceptance, has been reported after psycho-educational programmes. As healthcare professionals appear to play a significant role in providing support and education during regular follow-up visits, they may constitute an important social support system that could be another factor influencing device acceptance. However, little is known about the relationship between perceived support from healthcare professionals and device acceptance among recipients. A cross-sectional survey design. A sample comprising implantable cardioverter defibrillator recipients completed questionnaires assessing perceived support from healthcare professionals, shock anxiety and device acceptance. Demographic and clinical data were collected by self-report and from medical records in September-October 2010. The descriptive results indicated that approximately 85% of the recipients experienced high device acceptance. Regression analysis demonstrated that constructive support from healthcare professionals was positively associated with device acceptance and moderated the negative relationship between shock anxiety and device acceptance. Non-constructive support and shock anxiety had a negative statistical association with device acceptance. Healthcare professionals may represent a valuable constructive support system that can enhance device acceptance among implantable cardioverter defibrillator recipients, partly by preventing shock anxiety from leading to poor device acceptance. Non-constructive communication on the part of healthcare professionals could hinder device acceptance. © 2014 John Wiley & Sons Ltd.

Implantable biomedical devices on bioresorbable substrates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rogers, John A.; Kim, Dae-Hyeong; Omenetto, Fiorenzo

Provided herein are implantable biomedical devices and methods of administering implantable biomedical devices, making implantable biomedical devices, and using implantable biomedical devices to actuate a target tissue or sense a parameter associated with the target tissue in a biological environment.

16 CFR 1507.9 - Toy smoke devices and flitter devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... SUBSTANCES ACT REGULATIONS FIREWORKS DEVICES § 1507.9 Toy smoke devices and flitter devices. (a) Toy smoke... shall not be of such color and configuration so as to be confused with banned fireworks such as M-80...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nuzzo, Ralph G.; Rogers, John A.; Menard, Etienne

The invention provides methods and devices for fabricating printable semiconductor elements and assembling printable semiconductor elements onto substrate surfaces. Methods, devices and device components of the present invention are capable of generating a wide range of flexible electronic and optoelectronic devices and arrays of devices on substrates comprising polymeric materials. The present invention also provides stretchable semiconductor structures and stretchable electronic devices capable of good performance in stretched configurations.

Wireless event-recording device with identification codes

NASA Technical Reports Server (NTRS)

Watters, David G. (Inventor); Huestis, David L. (Inventor); Bahr, Alfred J. (Inventor)

2004-01-01

A wireless recording device can be interrogated to determine its identity and its state. The state indicates whether a particular physical or chemical event has taken place. In effect, the physical or chemical event is recorded by the device. The identity of the device allows it to be distinguished from a number of similar devices. Thus the sensor device may be used in an array of devices that can be probed by a wireless interrogation unit. The device tells the interrogator who it is and what state it is in. The interrogator can thus easily identify particular items in an array that have reached a particular condition.

Energy conversion device with support member having pore channels

DOEpatents

Routkevitch, Dmitri [Longmont, CO; Wind, Rikard A [Johnstown, CO

2014-01-07

Energy devices such as energy conversion devices and energy storage devices and methods for the manufacture of such devices. The devices include a support member having an array of pore channels having a small average pore channel diameter and having a pore channel length. Material layers that may include energy conversion materials and conductive materials are coaxially disposed within the pore channels to form material rods having a relatively small cross-section and a relatively long length. By varying the structure of the materials in the pore channels, various energy devices can be fabricated, such as photovoltaic (PV) devices, radiation detectors, capacitors, batteries and the like.

Micro devices using shape memory polymer patches for mated connections

DOEpatents

Lee, Abraham P.; Fitch, Joseph P.

2000-01-01

A method and micro device for repositioning or retrieving miniature devices located in inaccessible areas, such as medical devices (e.g., stents, embolic coils, etc.) located in a blood vessel. The micro repositioning or retrieving device and method uses shape memory polymer (SMP) patches formed into mating geometries (e.g., a hoop and a hook) for re-attachment of the deposited medical device to a catheter or guidewire. For example, SMP or other material hoops are formed on the medical device to be deposited in a blood vessel, and SMP hooks are formed on the micro device attached to a guidewire, whereby the hooks on the micro device attach to the hoops on the medical device, or vice versa, enabling deposition, movement, re-deposit, or retrieval of the medical device. By changing the temperature of the SMP hooks, the hooks can be attached to or released from the hoops located on the medical device. An exemplary method for forming the hooks and hoops involves depositing a sacrificial thin film on a substrate, patterning and processing the thin film to form openings therethrough, depositing or bonding SMP materials in the openings so as to be attached to the substrate, and removing the sacrificial thin film.

A literature review of the effects of computer input device design on biomechanical loading and musculoskeletal outcomes during computer work.

PubMed

Bruno Garza, J L; Young, J G

2015-01-01

Extended use of conventional computer input devices is associated with negative musculoskeletal outcomes. While many alternative designs have been proposed, it is unclear whether these devices reduce biomechanical loading and musculoskeletal outcomes. To review studies describing and evaluating the biomechanical loading and musculoskeletal outcomes associated with conventional and alternative input devices. Included studies evaluated biomechanical loading and/or musculoskeletal outcomes of users' distal or proximal upper extremity regions associated with the operation of alternative input devices (pointing devices, mice, other devices) that could be used in a desktop personal computing environment during typical office work. Some alternative pointing device designs (e.g. rollerbar) were consistently associated with decreased biomechanical loading while other designs had inconsistent results across studies. Most alternative keyboards evaluated in the literature reduce biomechanical loading and musculoskeletal outcomes. Studies of other input devices (e.g. touchscreen and gestural controls) were rare, however, those reported to date indicate that these devices are currently unsuitable as replacements for traditional devices. Alternative input devices that reduce biomechanical loading may make better choices for preventing or alleviating musculoskeletal outcomes during computer use, however, it is unclear whether many existing designs are effective.

The current situation and development of medical device testing institutes in China.

PubMed

Yang, Xiaofang; Mu, Ruihong; Fan, Yubo; Wang, Chunren; Li, Deyu

2017-04-01

This article analyses the current situation and development of Chinese medical device testing institutes from the perspectives of the two most important functions - testing functions and medical device standardization functions. Areas Covered: The objective of the Chinese government regulations for medical device industry is to ensure the safety and effectiveness of medical devices for Chinese patients. To support the regulation system, the Chinese government has established medical device testing institutes at different levels for example, the national, provincial, and municipal levels. These testing institutes also play an important role in technical support during medical device premarket registration and post market surveillance, they are also the vital practitioners of Chinese medical device standardization. Expert Commentary: Chinese medical device testing institutes are technical departments established by government, and serve the regulatory functions of government agency. In recent years, with the rapid development of medical device industry as well as constantly increasing international and domestic medical device market, the importance of medical device testing institute is more prominent, However, there are still some problems unsolved, such as their overall capacity remains to be improved, construction of standardization is to be strengthened, etc.

Design of a SIP device cooperation system on OSGi service platforms

NASA Astrophysics Data System (ADS)

Takayama, Youji; Koita, Takahiro; Sato, Kenya

2007-12-01

Home networks feature such various technologies as protocols, specifications, and middleware, including HTTP, UPnP, and Jini. A service platform is required to handle such technologies to enable them to cooperate with different devices. The OSGi service platform, which meets the requirements based on service-oriented architecture, is designed and standardized by OSGi Alliance and consists of two parts: one OSGi Framework and bundles. On the OSGi service platform, APIs are defined as services that can handle these technologies and are implemented in the bundle. By using the OSGi Framework with bundles, various technologies can cooperate with each other. On the other hand, in IP networks, Session Initiation Protocol (SIP) is often used in device cooperation services to resolve an IP address, control a session between two or more devices, and easily exchange the statuses of devices. However, since many existing devices do not correspond to SIP, it cannot be used for device cooperation services. A device that does not correspond to SIP is called an unSIP device. This paper proposes and implements a prototype system that enables unSIP devices to correspond to SIP. For unSIP devices, the proposed system provides device cooperation services with SIP.

Advancing medical device innovation through collaboration and coordination of structured data capture pilots: Report from the Medical Device Epidemiology Network (MDEpiNet) Specific, Measurable, Achievable, Results-Oriented, Time Bound (SMART) Think Tank.

PubMed

Reed, Terrie L; Drozda, Joseph P; Baskin, Kevin M; Tcheng, James; Conway, Karen; Wilson, Natalia; Marinac-Dabic, Danica; Heise, Theodore; Krucoff, Mitchell W

2017-12-01

The Medical Device Epidemiology Network (MDEpiNet) is a public private partnership (PPP) that provides a platform for collaboration on medical device evaluation and depth of expertise for supporting pilots to capture, exchange and use device information for improving device safety and protecting public health. The MDEpiNet SMART Think Tank, held in February, 2013, sought to engage expert stakeholders who were committed to improving the capture of device data, including Unique Device Identification (UDI), in key electronic health information. Prior to the Think Tank there was limited collaboration among stakeholders beyond a few single health care organizations engaged in electronic capture and exchange of device data. The Think Tank resulted in what has become two sustainable multi-stakeholder device data capture initiatives, BUILD and VANGUARD. These initiatives continue to mature within the MDEpiNet PPP structure and are well aligned with the goals outlined in recent FDA-initiated National Medical Device Planning Board and Medical Device Registry Task Force white papers as well as the vision for the National Evaluation System for health Technology.%. Published by Elsevier Inc.

Simulating ideal assistive devices to reduce the metabolic cost of walking with heavy loads.

PubMed

Dembia, Christopher L; Silder, Amy; Uchida, Thomas K; Hicks, Jennifer L; Delp, Scott L

2017-01-01

Wearable robotic devices can restore and enhance mobility. There is growing interest in designing devices that reduce the metabolic cost of walking; however, designers lack guidelines for which joints to assist and when to provide the assistance. To help address this problem, we used musculoskeletal simulation to predict how hypothetical devices affect muscle activity and metabolic cost when walking with heavy loads. We explored 7 massless devices, each providing unrestricted torque at one degree of freedom in one direction (hip abduction, hip flexion, hip extension, knee flexion, knee extension, ankle plantarflexion, or ankle dorsiflexion). We used the Computed Muscle Control algorithm in OpenSim to find device torque profiles that minimized the sum of squared muscle activations while tracking measured kinematics of loaded walking without assistance. We then examined the metabolic savings provided by each device, the corresponding device torque profiles, and the resulting changes in muscle activity. We found that the hip flexion, knee flexion, and hip abduction devices provided greater metabolic savings than the ankle plantarflexion device. The hip abduction device had the greatest ratio of metabolic savings to peak instantaneous positive device power, suggesting that frontal-plane hip assistance may be an efficient way to reduce metabolic cost. Overall, the device torque profiles generally differed from the corresponding net joint moment generated by muscles without assistance, and occasionally exceeded the net joint moment to reduce muscle activity at other degrees of freedom. Many devices affected the activity of muscles elsewhere in the limb; for example, the hip flexion device affected muscles that span the ankle joint. Our results may help experimentalists decide which joint motions to target when building devices and can provide intuition for how devices may interact with the musculoskeletal system. The simulations are freely available online, allowing others to reproduce and extend our work.

Simulating ideal assistive devices to reduce the metabolic cost of walking with heavy loads

PubMed Central

Silder, Amy; Uchida, Thomas K.; Hicks, Jennifer L.; Delp, Scott L.

2017-01-01

Wearable robotic devices can restore and enhance mobility. There is growing interest in designing devices that reduce the metabolic cost of walking; however, designers lack guidelines for which joints to assist and when to provide the assistance. To help address this problem, we used musculoskeletal simulation to predict how hypothetical devices affect muscle activity and metabolic cost when walking with heavy loads. We explored 7 massless devices, each providing unrestricted torque at one degree of freedom in one direction (hip abduction, hip flexion, hip extension, knee flexion, knee extension, ankle plantarflexion, or ankle dorsiflexion). We used the Computed Muscle Control algorithm in OpenSim to find device torque profiles that minimized the sum of squared muscle activations while tracking measured kinematics of loaded walking without assistance. We then examined the metabolic savings provided by each device, the corresponding device torque profiles, and the resulting changes in muscle activity. We found that the hip flexion, knee flexion, and hip abduction devices provided greater metabolic savings than the ankle plantarflexion device. The hip abduction device had the greatest ratio of metabolic savings to peak instantaneous positive device power, suggesting that frontal-plane hip assistance may be an efficient way to reduce metabolic cost. Overall, the device torque profiles generally differed from the corresponding net joint moment generated by muscles without assistance, and occasionally exceeded the net joint moment to reduce muscle activity at other degrees of freedom. Many devices affected the activity of muscles elsewhere in the limb; for example, the hip flexion device affected muscles that span the ankle joint. Our results may help experimentalists decide which joint motions to target when building devices and can provide intuition for how devices may interact with the musculoskeletal system. The simulations are freely available online, allowing others to reproduce and extend our work. PMID:28700630

A randomised control trial of prompt and feedback devices and their impact on quality of chest compressions--a simulation study.

PubMed

Yeung, Joyce; Davies, Robin; Gao, Fang; Perkins, Gavin D

2014-04-01

This study aims to compare the effect of three CPR prompt and feedback devices on quality of chest compressions amongst healthcare providers. A single blinded, randomised controlled trial compared a pressure sensor/metronome device (CPREzy), an accelerometer device (Phillips Q-CPR) and simple metronome on the quality of chest compressions on a manikin by trained rescuers. The primary outcome was compression depth. Secondary outcomes were compression rate, proportion of chest compressions with inadequate depth, incomplete release and user satisfaction. The pressure sensor device improved compression depth (37.24-43.64 mm, p=0.02), the accelerometer device decreased chest compression depth (37.38-33.19 mm, p=0.04) whilst the metronome had no effect (39.88 mm vs. 40.64 mm, p=0.802). Compression rate fell with all devices (pressure sensor device 114.68-98.84 min(-1), p=0.001, accelerometer 112.04-102.92 min(-1), p=0.072 and metronome 108.24 min(-1) vs. 99.36 min(-1), p=0.009). The pressure sensor feedback device reduced the proportion of compressions with inadequate depth (0.52 vs. 0.24, p=0.013) whilst the accelerometer device and metronome did not have a statistically significant effect. Incomplete release of compressions was common, but unaffected by the CPR feedback devices. Users preferred the accelerometer and metronome devices over the pressure sensor device. A post hoc study showed that de-activating the voice prompt on the accelerometer device prevented the deterioration in compression quality seen in the main study. CPR feedback devices vary in their ability to improve performance. In this study the pressure sensor device improved compression depth, whilst the accelerometer device reduced it and metronome had no effect. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Tulip deformity with Cera atrial septal defect devices: a report of 3 cases.

PubMed

Kohli, Vikas

2015-02-01

Device closure of secundum atrial septal defect (ASD) is the treatment of choice when anatomy is favourable. Amplatzer device has remained the gold standard for closure of ASD. Cobra deformity is a well-reported problem with devices. Recently, Tulip deformity has been reported in a single case. We report a series of cases where we noted Tulip deformity along with inability to retract the device in the sheath in Cera Lifetech devices. This resulted in prolongation of procedure, excessive fluoroscopic exposure and additional interventional procedures not usually anticipated in ASD device closure. We believe that the problem is due to the stiffness of the device resulting in its inability to be retracted into the sheath. We also report a unique way of retrieving the device.

Medical Devices; Immunology and Microbiology Devices; Classification of the Device To Detect and Identify Microbial Pathogen Nucleic Acids in Cerebrospinal Fluid. Final order.

PubMed

2017-10-20

The Food and Drug Administration (FDA or we) is classifying the device to detect and identify microbial pathogen nucleic acids in cerebrospinal fluid into class II (special controls). The special controls that will apply to the device type are identified in this order and will be part of the codified language for the device to detect and identify microbial pathogen nucleic acids in cerebrospinal fluid’s classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

Wireless device connection problems and design solutions

NASA Astrophysics Data System (ADS)

Song, Ji-Won; Norman, Donald; Nam, Tek-Jin; Qin, Shengfeng

2016-09-01

Users, especially the non-expert users, commonly experience problems when connecting multiple devices with interoperability. While studies on multiple device connections are mostly concentrated on spontaneous device association techniques with a focus on security aspects, the research on user interaction for device connection is still limited. More research into understanding people is needed for designers to devise usable techniques. This research applies the Research-through-Design method and studies the non-expert users' interactions in establishing wireless connections between devices. The "Learning from Examples" concept is adopted to develop a study focus line by learning from the expert users' interaction with devices. This focus line is then used for guiding researchers to explore the non-expert users' difficulties at each stage of the focus line. Finally, the Research-through-Design approach is used to understand the users' difficulties, gain insights to design problems and suggest usable solutions. When connecting a device, the user is required to manage not only the device's functionality but also the interaction between devices. Based on learning from failures, an important insight is found that the existing design approach to improve single-device interaction issues, such as improvements to graphical user interfaces or computer guidance, cannot help users to handle problems between multiple devices. This study finally proposes a desirable user-device interaction in which images of two devices function together with a system image to provide the user with feedback on the status of the connection, which allows them to infer any required actions.

Study on intelligent processing system of man-machine interactive garment frame model

NASA Astrophysics Data System (ADS)

Chen, Shuwang; Yin, Xiaowei; Chang, Ruijiang; Pan, Peiyun; Wang, Xuedi; Shi, Shuze; Wei, Zhongqian

2018-05-01

A man-machine interactive garment frame model intelligent processing system is studied in this paper. The system consists of several sensor device, voice processing module, mechanical parts and data centralized acquisition devices. The sensor device is used to collect information on the environment changes brought by the body near the clothes frame model, the data collection device is used to collect the information of the environment change induced by the sensor device, voice processing module is used for speech recognition of nonspecific person to achieve human-machine interaction, mechanical moving parts are used to make corresponding mechanical responses to the information processed by data collection device.it is connected with data acquisition device by a means of one-way connection. There is a one-way connection between sensor device and data collection device, two-way connection between data acquisition device and voice processing module. The data collection device is one-way connection with mechanical movement parts. The intelligent processing system can judge whether it needs to interact with the customer, realize the man-machine interaction instead of the current rigid frame model.

Method for accurately positioning a device at a desired area of interest

DOEpatents

Jones, Gary D.; Houston, Jack E.; Gillen, Kenneth T.

2000-01-01

A method for positioning a first device utilizing a surface having a viewing translation stage, the surface being movable between a first position where the viewing stage is in operational alignment with a first device and a second position where the viewing stage is in operational alignment with a second device. The movable surface is placed in the first position and an image is produced with the first device of an identifiable characteristic of a calibration object on the viewing stage. The moveable surface is then placed in the second position and only the second device is moved until an image of the identifiable characteristic in the second device matches the image from the first device. The calibration object is then replaced on the stage of the surface with a test object, and the viewing translation stage is adjusted until the second device images the area of interest. The surface is then moved to the first position where the test object is scanned with the first device to image the area of interest. An alternative embodiment where the devices move is also disclosed.