Comparison and Analysis of ISO/IEEE 11073, IHE PCD-01, and HL7 FHIR Messages for Personal Health Devices.

PubMed

Lee, Sungkee; Do, Hyoungho

2018-01-01

Increasing use of medical devices outside of healthcare facilities inevitably requires connectivity and interoperability between medical devices and healthcare information systems. To this end, standards have been developed and used to provide interoperability between personal health devices (PHDs) and external systems. ISO/IEEE 11073 standards and IHE PCD-01 standard messages have been used the most in the exchange of observation data of health devices. Recently, transmitting observation data using the HL7 FHIR standard has been devised in the name of DoF (Devices on FHIR) and adopted very fast. We compare and analyze these standards and suggest that which standard will work best at the different environments of device usage. We generated each message/resource of the three standards for observed vital signs from blood pressure monitor and thermometer. Then, the size, the contents, and the exchange processes of these messages are compared and analyzed. ISO/IEEE 11073 standard message has the smallest data size, but it has no ability to contain the key information, patient information. On the other hand, PCD-01 messages and FHIR standards have the fields for patient information. HL7 DoF standards provide reusing of information unit known as resource, and it is relatively easy to parse DoF messages since it uses widely known XML and JSON. ISO/IEEE 11073 standards are suitable for devices having very small computing power. IHE PCD-01 and HL7 DoF messages can be used for the devices that need to be connected to hospital information systems that require patient information. When information reuse is frequent, DoF is advantageous over PCD-01.

External Verification of SCADA System Embedded Controller Firmware

DTIC Science & Technology

2012-03-01

microprocessor and read-only memory (ROM) or flash memory for storing firmware and control logic [5],[8]. A PLC typically has three software levels as shown in...implementing different firmware. Because PLCs are in effect a microprocessor device, an analysis of the current research on embedded devices is important...Electronics Engineers (IEEE) published a 15 best practices guide for firmware control on microprocessors [44]. IEEE suggests that microprocessors

Nanoscale Devices for Solid State Refrigeration and Power Generation

DTIC Science & Technology

2004-01-01

techniques such as ballistic electron emission microscopy, scanning thermal microscopy, X - ray photoelectron emission spectroscopy, etc. The main emphasis is...0-7803-8363- X /04/$20.00 ©2004 IEEE 20th IEEE SEMI-THERM Symposium Nanoscale Devices for Solid State Refrigeration and Power Generation Ali...theories [9,23,24]. Since thermal conductivity is an average bulk effect involving many lattice vibrations (phonons modes), it is hard to

Novel Low Cost High Efficiency Tunable RF Devices and Antenna Arrays Design based on the Ferroelectric Materials and the CTS Technologies

DTIC Science & Technology

2011-02-14

licensed use limited to: UNIV OF HAWAII LIBRARY. Downloaded on June 18,2010 at 22:24:49 UTC from IEEE Xplore . Restrictions apply. KIM et al.: MODIFIED...limited to: UNIV OF HAWAII LIBRARY. Downloaded on June 18,2010 at 22:24:49 UTC from IEEE Xplore . Restrictions apply. 404 IEEE TRANSACTIONS ON...licensed use limited to: UNIV OF HAWAII LIBRARY. Downloaded on June 18,2010 at 22:24:49 UTC from IEEE Xplore . Restrictions apply. KIM et al

Robust Pressure-Actuated Liquid Metal Devices Showing Reconfigurable Electromagnetic Effects at GHz Frequencies (POSTPRINT)

DTIC Science & Technology

2014-06-01

IEEE Xplore , 978-1-4799-3540-6/14, pages 553-554. © 2014 IEEE . The U.S. Government is joint author of the work and has the right to use, modify...unlimited. See additional restrictions described on inside pages STINFO COPY © 2014 IEEE AIR FORCE RESEARCH LABORATORY MATERIALS AND...AR Brown-US, 3M101200250). The length of the dipole arms are changed via 553978-1-4799-3540-6/14/$31.00 ©2014 IEEE AP-S 2014 1 Distribution A

Calendar of Selected Aeronautical and Space Meetings (Calendrier des Manifestations Aeronautiques et Spatiales (Selection)).

DTIC Science & Technology

1983-01-01

Physique de l’Atmosphire et Environnement terrestre 71 09 - Information, Documentation et Informatique 74 10 - Thimes gin~raux (pluridisciplinaires) et...March Louisiana (US) Fiber Communication Optical Communications IEEE Fibre Optics Electro-Optics 02-08 7-9 March Baden-Baden VDE -IEEE Specialists...Conference on Very Large Electronic Systems VDE (GE) Scale Integrated Circuits Solid State Devices IEEE Integrated Circuits Engineering Design Fabrication

106-17 Telemetry Standards Recorder Data Packet Format Standard Chapter 11

DTIC Science & Technology

2017-07-01

11.2.2 PCM Data Packets ..................................................................................... 11-11 11.2.3 Time Data Packets...11-95 11.2.15 Ethernet Data Packets ................................................................................ 11-97 11.2.16 Time Space...4 Time ............................................................ 11-10 Figure 11-5. Secondary Header IEEE 1588 Time

75 FR 77002 - Expansion of the Scope of NRTL Recognition of Underwriters Laboratories Inc.; Modification to the...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-10

...): IEEE C37.20.4 Indoor AC Switches (1 kV-38 kV) for Use in Metal-Enclosed Switchgear \\a\\ IEEE C37.20.6 4.76 kV to 38 kV Rated Grounding and Testing Devices Used in Enclosures \\a\\ IEEE C37.23 Metal-Enclosed... Sprinkler Pipe for Fire Protection Service UL 962 Household and Commercial Furnishings \\c\\ UL 1340 Hoists UL...

46 CFR 167.40-1 - Electrical installations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... (Electrical Engineering) of this chapter. (3) Institute of Electrical and Electronic Engineers, Inc. (IEEE... 46 Shipping 7 2011-10-01 2011-10-01 false Electrical installations. 167.40-1 Section 167.40-1... SHIPS Certain Equipment Requirements § 167.40-1 Electrical installations. (a) Except as otherwise...

46 CFR 167.40-1 - Electrical installations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... (Electrical Engineering) of this chapter. (3) Institute of Electrical and Electronic Engineers, Inc. (IEEE... 46 Shipping 7 2012-10-01 2012-10-01 false Electrical installations. 167.40-1 Section 167.40-1... SHIPS Certain Equipment Requirements § 167.40-1 Electrical installations. (a) Except as otherwise...

46 CFR 167.40-1 - Electrical installations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... (Electrical Engineering) of this chapter. (3) Institute of Electrical and Electronic Engineers, Inc. (IEEE... 46 Shipping 7 2014-10-01 2014-10-01 false Electrical installations. 167.40-1 Section 167.40-1... SHIPS Certain Equipment Requirements § 167.40-1 Electrical installations. (a) Except as otherwise...

46 CFR 167.40-1 - Electrical installations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... (Electrical Engineering) of this chapter. (3) Institute of Electrical and Electronic Engineers, Inc. (IEEE... 46 Shipping 7 2013-10-01 2013-10-01 false Electrical installations. 167.40-1 Section 167.40-1... SHIPS Certain Equipment Requirements § 167.40-1 Electrical installations. (a) Except as otherwise...

76 FR 78174 - Energy Conservation Program: Test Procedure and Energy Conservation Standard for Set-Top Boxes...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-16

...): The capability to interface with external devices over a high bandwidth network (e.g., IEEE 802.11 (WiFi), MoCA, HPNA). For purposes of this specification, IEEE 802.3 wired Ethernet is not considered a...

Interoperability in digital electrocardiography: harmonization of ISO/IEEE x73-PHD and SCP-ECG.

PubMed

Trigo, Jesús D; Chiarugi, Franco; Alesanco, Alvaro; Martínez-Espronceda, Miguel; Serrano, Luis; Chronaki, Catherine E; Escayola, Javier; Martínez, Ignacio; García, José

2010-11-01

The ISO/IEEE 11073 (x73) family of standards is a reference frame for medical device interoperability. A draft for an ECG device specialization (ISO/IEEE 11073-10406-d02) has already been presented to the Personal Health Device (PHD) Working Group, and the Standard Communications Protocol for Computer-Assisted ElectroCardioGraphy (SCP-ECG) Standard for short-term diagnostic ECGs (EN1064:2005+A1:2007) has recently been approved as part of the x73 family (ISO 11073-91064:2009). These factors suggest the coordinated use of these two standards in foreseeable telecardiology environments, and hence the need to harmonize them. Such harmonization is the subject of this paper. Thus, a mapping of the mandatory attributes defined in the second draft of the ISO/IEEE 11073-10406-d02 and the minimum SCP-ECG fields is presented, and various other capabilities of the SCP-ECG Standard (such as the messaging part) are also analyzed from an x73-PHD point of view. As a result, this paper addresses and analyzes the implications of some inconsistencies in the coordinated use of these two standards. Finally, a proof-of-concept implementation of the draft x73-PHD ECG device specialization is presented, along with the conversion from x73-PHD to SCP-ECG. This paper, therefore, provides recommendations for future implementations of telecardiology systems that are compliant with both x73-PHD and SCP-ECG.

FPGA implementation cost and performance evaluation of IEEE 802.11 protocol encryption security schemes

NASA Astrophysics Data System (ADS)

Sklavos, N.; Selimis, G.; Koufopavlou, O.

2005-01-01

The explosive growth of internet and consumer demand for mobility has fuelled the exponential growth of wireless communications and networks. Mobile users want access to services and information, from both internet and personal devices, from a range of locations without the use of a cable medium. IEEE 802.11 is one of the most widely used wireless standards of our days. The amount of access and mobility into wireless networks requires a security infrastructure that protects communication within that network. The security of this protocol is based on the wired equivalent privacy (WEP) scheme. Currently, all the IEEE 802.11 market products support WEP. But recently, the 802.11i working group introduced the advanced encryption standard (AES), as the security scheme for the future IEEE 802.11 applications. In this paper, the hardware integrations of WEP and AES are studied. A field programmable gate array (FPGA) device has been used as the hardware implementation platform, for a fair comparison between the two security schemes. Measurements for the FPGA implementation cost, operating frequency, power consumption and performance are given.

Biomedical learning experiences for middle school girls sponsored by the Kansas State University Student Chapter of the IEEE EMBS.

PubMed

Gruber, Lucinda; Griffith, Connor; Young, Ethan; Sullivan, Adriann; Schuler, Jeff; Arnold-Christian, Susan; Warren, Steve

2009-01-01

Learning experiences for middle school girls are an effective means to steer young women toward secondary engineering curricula that they might not have otherwise considered. Sponsorship of such experiences by a collegiate student group is worthwhile, as it gives the group common purpose and places college students in a position to mentor these young women. This paper addresses learning experiences in different areas of bio-medical engineering offered to middle school girls in November 2008 via a day-long workshop entitled "Engineering The Body." The Kansas State University (KSU) Student Chapter of the IEEE Engineering in Medicine and Biology Society (EMBS) worked with the KSU Women in Engineering and Science Program (WESP) to design and sponsor these experiences, which addressed the areas of joint mechanics, electrocardiograms, membrane transport, computer mouse design, and audio filters for cochlear implants. Fifty five middle-school girls participated in this event, affirming the notion that biomedical engineering appeals to young women and that early education and recruitment efforts have the potential to expand the biomedical engineering talent pool.

Fundamental Studies of Electronic Properties of Materials and Devices for High Power, Compact Terahertz Vacuum Electron Devices

DTIC Science & Technology

2011-12-23

International Conference on Plasma Science, Karlsruhe, Germany, 2008. [9] K.J. Willis, S.C. Hagness, and I. Knezevic, “A global EMC/FDTD simulation...Materials,” 2010 IEEE AP-S International Symposium on Antennas and Propagation and 2010 USNC/ CNC /URSI Meeting in Toronto, ON, Canada, July 11-17...with a High-Q Quasioptical Resonator,” IEEE Int’l Conf. Plasma Sci., Chicago, IL, June 26-30, (2011), paper IO2B-4. [21] M.J. Weber, B.B. Yang, S.L

Continued Development of a Universal Network Interface Device Using the Intel 8086 and 8089 16-Bit Microprocessors.

DTIC Science & Technology

1983-12-15

7 "AD-RI38 iig CONTINUED DE VELOPMlENT OF UNIERSL NETWORK INTERFCE 1/2 DEVICE USING THE I..(U) AIR FORCE INST OF TECHD-F13 ill WRIGHT PATTERSON AFB...Protocols," IEEE Transactions on Communications, COM-28(4):433-44 (April 1980). 3. Borgsmiller, Michael. "The Serial Communications Interface Board...Interconnections," IEEE Transactions on Communications, COM-28(4): 425- 432, (April 1980). 4. I L Appendix A UNID II Data Flow Diagrams (Ref 10:26-34) This

Interoperable End-to-End Remote Patient Monitoring Platform Based on IEEE 11073 PHD and ZigBee Health Care Profile.

PubMed

Clarke, Malcolm; de Folter, Joost; Verma, Vivek; Gokalp, Hulya

2018-05-01

This paper describes the implementation of an end-to-end remote monitoring platform based on the IEEE 11073 standards for personal health devices (PHD). It provides an overview of the concepts and approaches and describes how the standard has been optimized for small devices with limited resources of processor, memory, and power that use short-range wireless technology. It explains aspects of IEEE 11073, including the domain information model, state model, and nomenclature, and how these support its plug-and-play architecture. It shows how these aspects underpin a much larger ecosystem of interoperable devices and systems that include IHE PCD-01, HL7, and BlueTooth LE medical devices, and the relationship to the Continua Guidelines, advocating the adoption of data standards and nomenclature to support semantic interoperability between health and ambient assisted living in future platforms. The paper further describes the adaptions that have been made in order to implement the standard on the ZigBee Health Care Profile and the experiences of implementing an end-to-end platform that has been deployed to frail elderly patients with chronic disease(s) and patients with diabetes.

Time and Energy Efficient Relay Transmission for Multi-Hop Wireless Sensor Networks.

PubMed

Kim, Jin-Woo; Barrado, José Ramón Ramos; Jeon, Dong-Keun

2016-06-27

The IEEE 802.15.4 standard is widely recognized as one of the most successful enabling technologies for short range low rate wireless communications and it is used in IoT applications. It covers all the details related to the MAC and PHY layers of the IoT protocol stack. Due to the nature of IoT, the wireless sensor networks are autonomously self-organized networks without infrastructure support. One of the issues in IoT is the network scalability. To address this issue, it is necessary to support the multi-hop topology. The IEEE 802.15.4 network can support a star, peer-to-peer, or cluster-tree topology. One of the IEEE 802.15.4 topologies suited for the high predictability of performance guarantees and energy efficient behavior is a cluster-tree topology where sensor nodes can switch off their transceivers and go into a sleep state to save energy. However, the IEEE 802.15.4 cluster-tree topology may not be able to provide sufficient bandwidth for the increased traffic load and the additional information may not be delivered successfully. The common drawback of the existing approaches is that they do not address the poor bandwidth utilization problem in IEEE 802.15.4 cluster-tree networks, so it is difficult to increase the network performance. Therefore, to solve this problem in this paper we study a relay transmission protocol based on the standard protocol in the IEEE 802.15.4 MAC. In the proposed scheme, the coordinators can relay data frames to their parent devices or their children devices without contention and can provide bandwidth for the increased traffic load or the number of devices. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the reliability, the end-to-end delay, and the energy consumption.

Time and Energy Efficient Relay Transmission for Multi-Hop Wireless Sensor Networks

PubMed Central

Kim, Jin-Woo; Barrado, José Ramón Ramos; Jeon, Dong-Keun

2016-01-01

The IEEE 802.15.4 standard is widely recognized as one of the most successful enabling technologies for short range low rate wireless communications and it is used in IoT applications. It covers all the details related to the MAC and PHY layers of the IoT protocol stack. Due to the nature of IoT, the wireless sensor networks are autonomously self-organized networks without infrastructure support. One of the issues in IoT is the network scalability. To address this issue, it is necessary to support the multi-hop topology. The IEEE 802.15.4 network can support a star, peer-to-peer, or cluster-tree topology. One of the IEEE 802.15.4 topologies suited for the high predictability of performance guarantees and energy efficient behavior is a cluster-tree topology where sensor nodes can switch off their transceivers and go into a sleep state to save energy. However, the IEEE 802.15.4 cluster-tree topology may not be able to provide sufficient bandwidth for the increased traffic load and the additional information may not be delivered successfully. The common drawback of the existing approaches is that they do not address the poor bandwidth utilization problem in IEEE 802.15.4 cluster-tree networks, so it is difficult to increase the network performance. Therefore, to solve this problem in this paper we study a relay transmission protocol based on the standard protocol in the IEEE 802.15.4 MAC. In the proposed scheme, the coordinators can relay data frames to their parent devices or their children devices without contention and can provide bandwidth for the increased traffic load or the number of devices. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the reliability, the end-to-end delay, and the energy consumption. PMID:27355952

Standardizing intensive care device data to enable secondary usages.

PubMed

Ingenerf, Josef; Kock, Ann-Kristin; Poelker, Marcel; Seidl, Konrad; Zeplin, Georg; Mersmann, Stefan; Handels, Heinz

2012-01-01

To represent medical device observations in a format that is consumable by clinical software, standards like HL7v3 and ISO/IEEE 11073 should be used jointly. This is demonstrated in a project with Dräger Medical GmbH focusing on their Patient Data Management System (PDMS) in intensive care, called Integrated Care Manager (ICM). Patient and device data of interest should be mapped to suitable formats to enable data exchange and decision support. Instead of mapping device data to target formats bilaterally we use a generic HL7v3 Refined Message Information Model (RMIM) with device specific parts adapted to ISO/IEEE 11073 DIM. The generality of the underlying model (based on Yuksel et al. [1]) allows the flexible inclusion of IEEE 11073 conformant device models of interest on the one hand and the generation of needed artifacts for secondary usages on the other hand, e.g. HL7 V2 messages, HL7 CDA documents like the Personal Health Monitoring Report (PHMR) or web services. Hence, once the medical device data are obtained in the RMIM format, it can quite easily be transformed into HL7-based standard interfaces through XSL transformations because these interfaces all have their building blocks from the same RIM. From there data can be accessed uniformly, e.g. as needed by Dräger´s decision support system SmartCare [2] for automated control and optimization of weaning from mechanical ventilation.

Microdosimetric Measurements on Nuclear Reactions.

DTIC Science & Technology

1983-01-01

applied to the field of radiation induced mutations. 130 BIBL OGI1APHY 1. T.C. May and M.H. Woods, IEEE Transactions on Electron Devices ED-l26, 2...McNulty, IEEE Transactions on Nuclear Science 11Sz29, 2012 (1982). 42. F.B. McLean and T.R. Oldham, ibid., NS-2.2, 2018 (1982). 43. G.C. Messenger

47 CFR 2.1093 - Radiofrequency radiation exposure evaluation: portable devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz,” ANSI/IEEE C95.1-1992... Electromagnetic Fields,” NCRP Report No. 86, Section 17.4.5. Copyright NCRP, 1986, Bethesda, Maryland 20814. SAR... Potentially Hazardous Electromagnetic Fields—RF and Microwave,” IEEE C95.3-1991. (4) For purposes of analyzing...

47 CFR 2.1093 - Radiofrequency radiation exposure evaluation: portable devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

... to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz,” ANSI/IEEE C95.1-1992... Electromagnetic Fields,” NCRP Report No. 86, Section 17.4.5. Copyright NCRP, 1986, Bethesda, Maryland 20814. SAR... Potentially Hazardous Electromagnetic Fields—RF and Microwave,” IEEE C95.3-1991. (4) For purposes of analyzing...

IEEE 802.15.4 MAC with GTS transmission for heterogeneous devices with application to wheelchair body-area sensor networks.

PubMed

Shrestha, Bharat; Hossain, Ekram; Camorlinga, Sergio

2011-09-01

In wireless personal area networks, such as wireless body-area sensor networks, stations or devices have different bandwidth requirements and, thus, create heterogeneous traffics. For such networks, the IEEE 802.15.4 medium access control (MAC) can be used in the beacon-enabled mode, which supports guaranteed time slot (GTS) allocation for time-critical data transmissions. This paper presents a general discrete-time Markov chain model for the IEEE 802.15.4-based networks taking into account the slotted carrier sense multiple access with collision avoidance and GTS transmission phenomena together in the heterogeneous traffic scenario and under nonsaturated condition. For this purpose, the standard GTS allocation scheme is modified. For each non-identical device, the Markov model is solved and the average service time and the service utilization factor are analyzed in the non-saturated mode. The analysis is validated by simulations using network simulator version 2.33. Also, the model is enhanced with a wireless propagation model and the performance of the MAC is evaluated in a wheelchair body-area sensor network scenario.

Use of E-Learning Functionalities and Standards: The Spanish Case

ERIC Educational Resources Information Center

Llamas-Nistal, M.; Caeiro-Rodriguez, M.; Castro, M.

2011-01-01

This paper shows the results of a survey performed in Spain on the different functionalities of e-learning platforms. This survey was filled in by a group of teachers, experts in engineering education from across Spain, within the scope of the Spanish Chapter of the IEEE Education Society. This paper presents their opinions on several aspects of…

WIH-based IEEE 802.11 ECG monitoring implementation.

PubMed

Moein, A; Pouladian, M

2007-01-01

New wireless technologies make possible the implementation of high level integration wireless devices which allow the replacement of traditional large wired monitoring devices. It offers new functionalities to physicians and will reduce the costs. Among these functionalities, biomedical signals can be sent to other devices (PDA, PC . . . ) or processing centers, without restricting the patients' mobility. This article discusses the WIH (Ward-In-Hand) structure and the software required for its implementation before an operational example is presented with its results. The aim of this project is the development and implementation of a reduced size electrocardiograph based on IEEE 802.11 with high speed and more accuracy, which allows wireless monitoring of patients, and the insertion of the information into the Wi-Fi hospital networks.

Interoperability of medical device information and the clinical applications: an HL7 RMIM based on the ISO/IEEE 11073 DIM.

PubMed

Yuksel, Mustafa; Dogac, Asuman

2011-07-01

Medical devices are essential to the practice of modern healthcare services. Their benefits will increase if clinical software applications can seamlessly acquire the medical device data. The need to represent medical device observations in a format that can be consumable by clinical applications has already been recognized by the industry. Yet, the solutions proposed involve bilateral mappings from the ISO/IEEE 11073 Domain Information Model (DIM) to specific message or document standards. Considering that there are many different types of clinical applications such as the electronic health record and the personal health record systems, the clinical workflows, and the clinical decision support systems each conforming to different standard interfaces, detailing a mapping mechanism for every one of them introduces significant work and, thus, limits the potential health benefits of medical devices. In this paper, to facilitate the interoperability of clinical applications and the medical device data, we use the ISO/IEEE 11073 DIM to derive an HL7 v3 Refined Message Information Model (RMIM) of the medical device domain from the HL7 v3 Reference Information Mode (RIM). This makes it possible to trace the medical device data back to a standard common denominator, that is, HL7 v3 RIM from which all the other medical domains under HL7 v3 are derived. Hence, once the medical device data are obtained in the RMIM format, it can easily be transformed into HL7-based standard interfaces through XML transformations because these interfaces all have their building blocks from the same RIM. To demonstrate this, we provide the mappings from the developed RMIM to some of the widely used HL7 v3-based standard interfaces.

Accurate Energy Consumption Modeling of IEEE 802.15.4e TSCH Using Dual-BandOpenMote Hardware.

PubMed

Daneels, Glenn; Municio, Esteban; Van de Velde, Bruno; Ergeerts, Glenn; Weyn, Maarten; Latré, Steven; Famaey, Jeroen

2018-02-02

The Time-Slotted Channel Hopping (TSCH) mode of the IEEE 802.15.4e amendment aims to improve reliability and energy efficiency in industrial and other challenging Internet-of-Things (IoT) environments. This paper presents an accurate and up-to-date energy consumption model for devices using this IEEE 802.15.4e TSCH mode. The model identifies all network-related CPU and radio state changes, thus providing a precise representation of the device behavior and an accurate prediction of its energy consumption. Moreover, energy measurements were performed with a dual-band OpenMote device, running the OpenWSN firmware. This allows the model to be used for devices using 2.4 GHz, as well as 868 MHz. Using these measurements, several network simulations were conducted to observe the TSCH energy consumption effects in end-to-end communication for both frequency bands. Experimental verification of the model shows that it accurately models the consumption for all possible packet sizes and that the calculated consumption on average differs less than 3% from the measured consumption. This deviation includes measurement inaccuracies and the variations of the guard time. As such, the proposed model is very suitable for accurate energy consumption modeling of TSCH networks.

Accurate Energy Consumption Modeling of IEEE 802.15.4e TSCH Using Dual-BandOpenMote Hardware

PubMed Central

Municio, Esteban; Van de Velde, Bruno; Latré, Steven

2018-01-01

The Time-Slotted Channel Hopping (TSCH) mode of the IEEE 802.15.4e amendment aims to improve reliability and energy efficiency in industrial and other challenging Internet-of-Things (IoT) environments. This paper presents an accurate and up-to-date energy consumption model for devices using this IEEE 802.15.4e TSCH mode. The model identifies all network-related CPU and radio state changes, thus providing a precise representation of the device behavior and an accurate prediction of its energy consumption. Moreover, energy measurements were performed with a dual-band OpenMote device, running the OpenWSN firmware. This allows the model to be used for devices using 2.4 GHz, as well as 868 MHz. Using these measurements, several network simulations were conducted to observe the TSCH energy consumption effects in end-to-end communication for both frequency bands. Experimental verification of the model shows that it accurately models the consumption for all possible packet sizes and that the calculated consumption on average differs less than 3% from the measured consumption. This deviation includes measurement inaccuracies and the variations of the guard time. As such, the proposed model is very suitable for accurate energy consumption modeling of TSCH networks. PMID:29393900

Portable Integrated Wireless Device Threat Assessment to Aircraft Radio Systems

NASA Technical Reports Server (NTRS)

Salud, Maria Theresa P.; Williams, Reuben A. (Technical Monitor)

2004-01-01

An assessment was conducted on multiple wireless local area network (WLAN) devices using the three wireless standards for spurious radiated emissions to determine their threat to aircraft radio navigation systems. The measurement process, data and analysis are provided for devices tested using IEEE 802.11a, IEEE 802.11b, and Bluetooth as well as data from portable laptops/tablet PCs and PDAs (grouping known as PEDs). A comparison was made between wireless LAN devices and portable electronic devices. Spurious radiated emissions were investigated in the radio frequency bands for the following aircraft systems: Instrument Landing System Localizer and Glideslope, Very High Frequency (VHF) Communication, VHF Omnidirectional Range, Traffic Collision Avoidance System, Air Traffic Control Radar Beacon System, Microwave Landing System and Global Positioning System. Since several of the contiguous navigation systems were grouped under one encompassing measurement frequency band, there were five measurement frequency bands where spurious radiated emissions data were collected for the PEDs and WLAN devices. The report also provides a comparison between emissions data and regulatory emission limit.

New IEEE 11073 Standards for interoperable, networked Point-of-Care Medical Devices.

PubMed

Kasparick, Martin; Schlichting, Stefan; Golatowski, Frank; Timmermann, Dirk

2015-08-01

Surgical procedures become more and more complex and the number of medical devices in an operating room (OR) increases continuously. Today's vendor-dependent solutions for integrated ORs are not able to handle this complexity. They can only form isolated solutions. Furthermore, high costs are a result of vendor-dependent approaches. Thus we present a service-oriented device communication for distributed medical systems that enables the integration and interconnection between medical devices among each other and to (medical) information systems, including plug-and-play functionality. This system will improve patient's safety by making technical complexity of a comprehensive integration manageable. It will be available as open standards that are part of the IEEE 11073 family of standards. The solution consists of a service-oriented communication technology, the so called Medical Devices Profile for Web Services (MDPWS), a Domain Information & Service Model, and a binding between the first two mechanisms. A proof of this concept has been done with demonstrators of real world OR devices.

Telemetry Standards, IRIG Standard 106-17. Chapter 10. Digital Recording Standard

DTIC Science & Technology

2017-07-01

10-28 10.7.9 Required Discrete Control Functions...1553 data bus, time, analog, video, Aeronautical Radio, Inc. 429, discrete , and Universal Asynchronous Receiver and Transmitter containing...Interfaces 10.3, 10.4 Fibre Channel and/or IEEE 1394b Data Download Port 10.3, 10.7 Discrete Lines and/or RS-232 and 422 Full Duplex Communication 10.3

Conductivity Of Explosively Shocked Potassium Chloride

DTIC Science & Technology

2009-06-01

explosives and in a light gas gun were performed in [6, 7, 10]. In these works, it was demonstrated that KCl samples pass through the dielectric-to... plasma on the recorded signals. (a) (b) Figure 1. Schematic diagram of the device developed for investigation...Papers 1976-2013, and Abstracts of the 2013 IEEE International Conference on Plasma Science. IEEE International Pulsed Power Conference (19th). Held in San

Intelligent Distribution Voltage Control with Distributed Generation =

NASA Astrophysics Data System (ADS)

Castro Mendieta, Jose

In this thesis, three methods for the optimal participation of the reactive power of distributed generations (DGs) in unbalanced distributed network have been proposed, developed, and tested. These new methods were developed with the objectives of maintain voltage within permissible limits and reduce losses. The first method proposes an optimal participation of reactive power of all devices available in the network. The propose approach is validated by comparing the results with other methods reported in the literature. The proposed method was implemented using Simulink of Matlab and OpenDSS. Optimization techniques and the presentation of results are from Matlab. The co-simulation of Electric Power Research Institute's (EPRI) OpenDSS program solves a three-phase optimal power flow problem in the unbalanced IEEE 13 and 34-node test feeders. The results from this work showed a better loss reduction compared to the Coordinated Voltage Control (CVC) method. The second method aims to minimize the voltage variation on the pilot bus on distribution network using DGs. It uses Pareto and Fuzzy-PID logic to reduce the voltage variation. Results indicate that the proposed method reduces the voltage variation more than the other methods. Simulink of Matlab and OpenDSS is used in the development of the proposed approach. The performance of the method is evaluated on IEEE 13-node test feeder with one and three DGs. Variables and unbalanced loads are used, based on real consumption data, over a time window of 48 hours. The third method aims to minimize the reactive losses using DGs on distribution networks. This method analyzes the problem using the IEEE 13-node test feeder with three different loads and the IEEE 123-node test feeder with four DGs. The DGs can be fixed or variables. Results indicate that integration of DGs to optimize the reactive power of the network helps to maintain the voltage within the allowed limits and to reduce the reactive power losses. The thesis is presented in the form of the three articles. The first article is published in the journal Electrical Power and Energy System, the second is published in the international journal Energies and the third was submitted to the journal Electrical Power and Energy System. Two other articles have been published in conferences with reviewing committee. This work is based on six chapters, which are detailed in the various sections of the thesis.

An Analytical Model for the Performance Analysis of Concurrent Transmission in IEEE 802.15.4

PubMed Central

Gezer, Cengiz; Zanella, Alberto; Verdone, Roberto

2014-01-01

Interference is a serious cause of performance degradation for IEEE802.15.4 devices. The effect of concurrent transmissions in IEEE 802.15.4 has been generally investigated by means of simulation or experimental activities. In this paper, a mathematical framework for the derivation of chip, symbol and packet error probability of a typical IEEE 802.15.4 receiver in the presence of interference is proposed. Both non-coherent and coherent demodulation schemes are considered by our model under the assumption of the absence of thermal noise. Simulation results are also added to assess the validity of the mathematical framework when the effect of thermal noise cannot be neglected. Numerical results show that the proposed analysis is in agreement with the measurement results on the literature under realistic working conditions. PMID:24658624

An analytical model for the performance analysis of concurrent transmission in IEEE 802.15.4.

PubMed

Gezer, Cengiz; Zanella, Alberto; Verdone, Roberto

2014-03-20

Interference is a serious cause of performance degradation for IEEE802.15.4 devices. The effect of concurrent transmissions in IEEE 802.15.4 has been generally investigated by means of simulation or experimental activities. In this paper, a mathematical framework for the derivation of chip, symbol and packet error probability of a typical IEEE 802.15.4 receiver in the presence of interference is proposed. Both non-coherent and coherent demodulation schemes are considered by our model under the assumption of the absence of thermal noise. Simulation results are also added to assess the validity of the mathematical framework when the effect of thermal noise cannot be neglected. Numerical results show that the proposed analysis is in agreement with the measurement results on the literature under realistic working conditions.

Real-Time Optimization in Complex Stochastic Environment

DTIC Science & Technology

2015-06-24

simpler ones, thus addressing scalability and the limited resources of networked wireless devices. This, however, comes at the expense of increased...Maximization of Wireless Sensor Networks with Non-ideal Batteries”, IEEE Trans. on Control of Network Systems, Vol. 1, 1, pp. 86-98, 2014. [27...C.G., “Optimal Energy-Efficient Downlink Transmission Scheduling for Real-Time Wireless Networks ”, subm. to IEEE Trans. on Control of Network Systems

Software Defined Network Monitoring Scheme Using Spectral Graph Theory and Phantom Nodes

DTIC Science & Technology

2014-09-01

networks is the emergence of software - defined networking ( SDN ) [1]. SDN has existed for the...Chapter III for network monitoring. A. SOFTWARE DEFINED NETWORKS SDNs provide a new and innovative method to simplify network hardware by logically...and R. Giladi, “Performance analysis of software - defined networking ( SDN ),” in Proc. of IEEE 21st International Symposium on Modeling, Analysis

IEEE-1588(Trademark) Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control Systems

DTIC Science & Technology

2002-12-01

34th Annual Precise Time and Time Interval (PTTI) Meeting 243 IEEE-1588™ STANDARD FOR A PRECISION CLOCK SYNCHRONIZATION PROTOCOL FOR... synchronization . 2. Cyclic-systems. In cyclic-systems, timing is periodic and is usually defined by the characteristics of a cyclic network or bus...incommensurate, timing schedules for each device are easily implemented. In addition, synchronization accuracy depends on the accuracy of the common

The Sound of Freedom. Naval Weapons Technology at Dahlgren, Virginia, 1918-2006

DTIC Science & Technology

2006-01-01

the TRINITY device, before later succeeding J. Robert Oppenheimer as the director of Los Alamos National Laboratory. Other former Dahlgren...and the Computer (Cambridge, Mass.: The MIT Press, 1999); Michael R. Williams, A History of Computing Technology, 2nd ed. ( Los Alamos , Calif.: IEEE...Minutes of Advisory Council. 3. Ibid. 4. Ibid.; Michael R. Williams, A History of Computing Technology, 2nd ed. ( Los Alamos , Calif.: IEEE Computer

Biometric identity management for standard mobile medical networks.

PubMed

Egner, Alexandru; Soceanu, Alexandru; Moldoveanu, Florica

2012-01-01

The explosion of healthcare costs over the last decade has prompted the ICT industry to respond with solutions for reducing costs while improving healthcare quality. The ISO/IEEE 11073 family of standards recently released is the first step towards interoperability of mobile medical devices used in patient environments. The standards do not, however, tackle security problems, such as identity management, or the secure exchange of medical data. This paper proposes an enhancement of the ISO/IEEE 11073-20601 protocol with an identity management system based on biometry. The paper describes a novel biometric-based authentication process, together with the biometric key generation algorithm. The proposed extension of the ISO/IEEE 11073-20601 is also presented.

Dynamic Control of Facts Devices to Enable Large Scale Penetration of Renewable Energy Resources

NASA Astrophysics Data System (ADS)

Chavan, Govind Sahadeo

This thesis focuses on some of the problems caused by large scale penetration of Renewable Energy Resources within EHV transmission networks, and investigates some approaches in resolving these problems. In chapter 4, a reduced-order model of the 500 kV WECC transmission system is developed by estimating its key parameters from phasor measurement unit (PMU) data. The model was then implemented in RTDS and was investigated for its accuracy with respect to the PMU data. Finally it was tested for observing the effects of various contingencies like transmission line loss, generation loss and large scale penetration of wind farms on EHV transmission systems. Chapter 5 introduces Static Series Synchronous Compensators (SSSC) which are seriesconnected converters that can control real power flow along a transmission line. A new application of SSSCs in mitigating Ferranti effect on unloaded transmission lines was demonstrated on PSCAD. A new control scheme for SSSCs based on the Cascaded H-bridge (CHB) converter configuration was proposed and was demonstrated using PSCAD and RTDS. A new centralized controller was developed for the distributed SSSCs based on some of the concepts used in the CHB-based SSSC. The controller's efficacy was demonstrated using RTDS. Finally chapter 6 introduces the problem of power oscillations induced by renewable sources in a transmission network. A power oscillation damping (POD) controller is designed using distributed SSSCs in NYPA's 345 kV three-bus AC system and its efficacy is demonstrated in PSCAD. A similar POD controller is then designed for the CHB-based SSSC in the IEEE 14 bus system in PSCAD. Both controllers were noted to have significantly damped power oscillations in the transmission networks.

Appropriate Measures and Consistent Standard for High Energy Laser Beam Quality (Postprint)

DTIC Science & Technology

2006-08-01

another. a We follow the 99% criteria [ Siegman , Lasers , chapter 17.1] which corresponds to a... Siegman , “ Lasers ” University Science Books, 1986. • A.E. Siegman , “New developments in laser resonators”, SPIE Vol. 1224, Optical Resonators, 1990...pp. 1-14. • Anthony E. Siegman & Steven W. Townsend, “Output Beam Propagation and Beam Quality from a Multimode Stable-Cavity Laser ”, IEEE Journal

Achievable Rate Estimation of IEEE 802.11ad Visual Big-Data Uplink Access in Cloud-Enabled Surveillance Applications.

PubMed

Kim, Joongheon; Kim, Jong-Kook

2016-01-01

This paper addresses the computation procedures for estimating the impact of interference in 60 GHz IEEE 802.11ad uplink access in order to construct visual big-data database from randomly deployed surveillance camera sensing devices. The acquired large-scale massive visual information from surveillance camera devices will be used for organizing big-data database, i.e., this estimation is essential for constructing centralized cloud-enabled surveillance database. This performance estimation study captures interference impacts on the target cloud access points from multiple interference components generated by the 60 GHz wireless transmissions from nearby surveillance camera devices to their associated cloud access points. With this uplink interference scenario, the interference impacts on the main wireless transmission from a target surveillance camera device to its associated target cloud access point with a number of settings are measured and estimated under the consideration of 60 GHz radiation characteristics and antenna radiation pattern models.

Clinical efficacy and effectiveness of 3D printing: a systematic review

PubMed Central

Diment, Laura E; Thompson, Mark S; Bergmann, Jeroen H M

2017-01-01

Objective To evaluate the clinical efficacy and effectiveness of using 3D printing to develop medical devices across all medical fields. Design Systematic review compliant with Preferred Reporting Items for Systematic Reviews and Meta-Analyses. Data sources PubMed, Web of Science, OVID, IEEE Xplore and Google Scholar. Methods A double-blinded review method was used to select all abstracts up to January 2017 that reported on clinical trials of a three-dimensional (3D)-printed medical device. The studies were ranked according to their level of evidence, divided into medical fields based on the International Classification of Diseases chapter divisions and categorised into whether they were used for preoperative planning, aiding surgery or therapy. The Downs and Black Quality Index critical appraisal tool was used to assess the quality of reporting, external validity, risk of bias, risk of confounding and power of each study. Results Of the 3084 abstracts screened, 350 studies met the inclusion criteria. Oral and maxillofacial surgery contained 58.3% of studies, and 23.7% covered the musculoskeletal system. Only 21 studies were randomised controlled trials (RCTs), and all fitted within these two fields. The majority of RCTs were 3D-printed anatomical models for preoperative planning and guides for aiding surgery. The main benefits of these devices were decreased surgical operation times and increased surgical accuracy. Conclusions All medical fields that assessed 3D-printed devices concluded that they were clinically effective. The fields that most rigorously assessed 3D-printed devices were oral and maxillofacial surgery and the musculoskeletal system, both of which concluded that the 3D-printed devices outperformed their conventional comparators. However, the efficacy and effectiveness of 3D-printed devices remain undetermined for the majority of medical fields. 3D-printed devices can play an important role in healthcare, but more rigorous and long-term assessments are needed to determine if 3D-printed devices are clinically relevant before they become part of standard clinical practice. PMID:29273650

APS-Workshop on Characterization of MMIC (Monolithic Microwave Integrated Circuit) Devices for Array Antenna

NASA Technical Reports Server (NTRS)

Smetana, Jerry (Editor); Mittra, Raj (Editor); Laprade, Nick; Edward, Bryan; Zaghloul, Amir

1987-01-01

The IEEE AP-S ADCOM is attempting to expand its educational, tutorial and information exchange activities as a further benefit to all members. To this end, ADCOM will be forming specialized workshops on topics of interest to its members. The first such workshop on Characterization and Packaging of MMIC Devices for Array Antennas was conceived. The workshop took place on June 13, 1986 as part of the 1986 International Symposium sponsored by IEEE AP-S and URSI in Philadelphia, PA, June 9-13, 1986. The workshop was formed to foster the interchange of ideas among MMIC device users and to provide a forum to collect and focus information among engineers experienced and interested in the topic. After brief presentations by the panelists and comments from attendees on several subtopics, the group was divided into working committees. Each committee evaluated and made recommendations on one of the subtopics.

Implementing ISO/IEEE 11073: proposal of two different strategic approaches.

PubMed

Martínez-Espronceda, M; Serrano, L; Martínez, I; Escayola, J; Led, S; Trigo, J; García, J

2008-01-01

This paper explains the challenges encountered during the ISO/IEEE 11073 standard implementation process. The complexity of the standard and the consequent heavy requirements, which have not encouraged software engineers to adopt the standard. The developing complexity evaluation drives us to propose two possible implementation strategies that cover almost all possible use cases and eases handling the standard by non-expert users. The first one is focused on medical devices (MD) and proposes a low-memory and low-processor usage technique. It is based on message patterns that allow simple functions to generate ISO/IEEE 11073 messages and to process them easily. In this way a framework for MDs can be obtained. Second one is focused on more powerful machines such as data loggers or gateways (aka. computer engines (CE)), which do not have the MDs' memory and processor usage constraints. For CEs a more intelligent and adaptative Plug&Play (P&P) solution is provided. It consists on a general platform that can access to any device supported by the standard. Combining both strategies will cut developing time for applications based on ISO/EEE 11073.

Quasi-one dimensional (Q1D) nanostructures: Synthesis, integration and device application

NASA Astrophysics Data System (ADS)

Chien, Chung-Jen

Quasi-one-dimensional (Q1D) nanostructures such as nanotubes and nanowires have been widely regarded as the potential building blocks for nanoscale electronic, optoelectronic and sensing devices. In this work, the content can be divided into three categories: Nano-material synthesis and characterizations, alignment and integration, physical properties and application. The dissertation consists of seven chapters as following. Chapter 1 will give an introduction to low dimensional nano-materials. Chapter 2 explains the mechanism how Q1D nanostructure grows. Chapter 3 describes the methods how we horizontally and vertically align the Q1D nanostructure. Chapter 4 and 5 are the electrical and optical device characterization respectively. Chapter 6 demonstrates the integration of Q1D nanostructures and the device application. The last chapter will discuss the future work and conclusion of the thesis.

Performance Analysis of IEEE 802.15.3 MAC Protocol with Different ACK Polices

NASA Astrophysics Data System (ADS)

Mehta, S.; Kwak, K. S.

The wireless personal area network (WPAN) is an emerging wireless technology for future short range indoor and outdoor communication applications. The IEEE 802.15.3 medium access control (MAC) is proposed, specially, for short range high data rates applications, to coordinate the access to the wireless medium among the competing devices. This paper uses analytical model to study the performance analysis of WPAN (IEEE 802.15.3) MAC in terms of throughput, efficient bandwidth utilization, and delay with various acknowledgment schemes under different parameters. Also, some important observations are obtained, which can be very useful to the protocol architectures. Finally, we come up with some important research issues to further investigate the possible improvements in the WPAN MAC.

Advancements in Radio Frequency (RF) Photonics for Signal Processing Applications on Avionic Platforms (Preprint)

DTIC Science & Technology

2013-10-01

links and their impact on device design,” IEEE Trans. Microwave Theory and Tech., 54, pp. 906-920, 2006. [2] V. Urick , F. Bucholtz, P. Devgan, J...photonic links,” IEEE Trans. Microwave Theory and Tech., 55, pp. 1978-1985, 2007. [3] P. Devgan, J. Diehl, V. Urick , C. Sunderman, and K. Williams...outputs," Opt. Express, 17, pp. 9028-9039, 2009. [4] P. Devgan, A. Hastings, V. Urick , and K. Williams, "Cancellation of photodiode-induced second

Media Access Time-Rearrangement of Wireless LAN for a Multi-Radio Collocated Platform

NASA Astrophysics Data System (ADS)

Shin, Sang-Heon; Kim, Chul; Park, Sang Kyu

With the advent of new Radio Access Technologies (RATs), it is inevitable that several RATs will co-exist, especially in the license-exempt band. In this letter, we present an in-depth adaptation of the proactive time-rearrangement (PATRA) scheme for IEEE 802.11 WLAN. The PATRA is a time division approach for reducing interference from a multi-radio device. Because IEEE 802.11 is based on carrier sensing and contention mechanism, it is the most suitable candidate to adapt the PATRA.

A comprehensive model on field-effect pnpn devices (Z2-FET)

NASA Astrophysics Data System (ADS)

Taur, Yuan; Lacord, Joris; Parihar, Mukta Singh; Wan, Jing; Martinie, Sebastien; Lee, Kyunghwa; Bawedin, Maryline; Barbe, Jean-Charles; Cristoloveanu, Sorin

2017-08-01

A comprehensive model for field-effect pnpn devices (Z2-FET) is presented. It is based on three current continuity equations coupled to two MOS equations. The model reproduces the characteristic S-shaped I-V curve when the device is driven by a current source. The negative resistance region at intermediate currents occurs as the center junction undergoes a steep transition from reverse to forward bias. Also playing a vital role are the mix and match of the minority carrier diffusion current and the generation recombination current. Physical insights to the key mechanisms at work are gained by regional approximations of the model, from which analytical expressions for the maximum and minimum voltages at the switching points are derived. From 1981 to 2001, he was with the Silicon Technology Department of IBM Thomas J. Watson Research Center, Yorktown Heights, New York, where he was Manager of Exploratory Devices and Processes. Areas in which he has worked and published include latchup-free 1-um CMOS, self-aligned TiSi2, 0.5-um CMOS and BiCMOS, shallow trench isolation, 0.25-um CMOS with n+/p + poly gates, SOI, low-temperature CMOS, and 0.1-um CMOS. Since October 2001, he has been a professor in the Department of Electrical and Computer Engineering, University of California, San Diego. Dr. Yuan Taur was elected a Fellow of the IEEE in 1998. He has served as Editor-in-Chief of the IEEE Electron Device Letters from 1999 to 2011. He authored or co-authored over 200 technical papers and holds 14 U.S. patents. He co-authored a book, ;Fundamentals of Modern VLSI Devices,; published by Cambridge University Press in 1998. The 2nd edition was published in 2009. Dr. Yuan Taur received IEEE Electron Devices Society's J. J. Ebers Award in 2012 ;for contributions to the advancement of several generations of CMOS process technologies.;

Integration of IEEE 1451 and HL7 exchanging information for patients' sensor data.

PubMed

Kim, Wooshik; Lim, Suyoung; Ahn, Jinsoo; Nah, Jiyoung; Kim, Namhyun

2010-12-01

HL7 (Health Level 7) is a standard developed for exchanging incompatible healthcare information generated from programs or devices among heterogenous medical information systems. At present, HL7 is growing as a global standard. However, the HL7 standard does not support effective methods for treating data from various medical sensors, especially from mobile sensors. As ubiquitous systems are growing, HL7 must communicate with various medical transducers. In the area of sensor fields, IEEE 1451 is a group of standards for controlling transducers and for communicating data from/to various transducers. In this paper, we present the possibility of interoperability between the two standards, i.e., HL7 and IEEE 1451. After we present a method to integrate them and show the preliminary results of this approach.

Editorial Conference Comments by the General Chair

NASA Astrophysics Data System (ADS)

Reed, Robert A.

2017-01-01

The 53rd IEEE Nuclear and Space Radiation Effects Conference (NSREC) was held July 11-15, 2016, at the Oregon Convention Center in Portland; the conference hotel was the Portland Doubletree. The NSREC is recognized as one of the premier international conferences on radiation effects in electronic materials, devices, and systems. The 2016 conference continued this tradition with a strong technical program, a one-day tutorial short course, radiation effects data workshop, industrial exhibit, and meetings for the IEEE Women in Engineering and Young Professionals organizations. The conference was sponsored by the Radiation Effects Committee of the IEEE Nuclear and Plasma Sciences Society (NPSS), and supported by Atmel, BAE Systems, Boeing, Cobham Semiconductor Solutions, Freebird Semiconductor, Honeywell, International Rectifier, Intersil Corporation, Jet Propulsion Laboratory, Northrop Grumman, Southwest Research Institute, and VPT Rad.

Methods to Account for Accelerated Semi-Conductor Device Wearout in Longlife Aerospace Applications

DTIC Science & Technology

2003-01-01

Vasi, “Device scalling effects on hot-carrier induced interface and oxide-trappoing charge distributions in MOSFETs,” IEEE Transactions on Electron...Symposium Proceedings, pp. 248–254, 2002. [104] S. I. A. ( SIA ), “International technology roadmap for semiconductors.” <www.semichips.org>, 1999. 113

3D workflow for HDR image capture of projection systems and objects for CAVE virtual environments authoring with wireless touch-sensitive devices

NASA Astrophysics Data System (ADS)

Prusten, Mark J.; McIntyre, Michelle; Landis, Marvin

2006-02-01

A 3D workflow pipeline is presented for High Dynamic Range (HDR) image capture of projected scenes or objects for presentation in CAVE virtual environments. The methods of HDR digital photography of environments vs. objects are reviewed. Samples of both types of virtual authoring being the actual CAVE environment and a sculpture are shown. A series of software tools are incorporated into a pipeline called CAVEPIPE, allowing for high-resolution objects and scenes to be composited together in natural illumination environments [1] and presented in our CAVE virtual reality environment. We also present a way to enhance the user interface for CAVE environments. The traditional methods of controlling the navigation through virtual environments include: glove, HUD's and 3D mouse devices. By integrating a wireless network that includes both WiFi (IEEE 802.11b/g) and Bluetooth (IEEE 802.15.1) protocols the non-graphical input control device can be eliminated. Therefore wireless devices can be added that would include: PDA's, Smart Phones, TabletPC's, Portable Gaming consoles, and PocketPC's.

Modeling Respiratory Gas Dynamics in the Aviator’s Breathing System. Volume 2. Appendices

DTIC Science & Technology

1994-05-01

Rideout, at at. Dfference-Differentlat Equations for Fluid C... Flow in Distensible Tubes. IEEE Transactions on Bio-Medlcat C... Enginhering. Vot INE-14...McGraw-Hill; 1970; Chapter 13: 433-450. 12. Astrand, PO; Saltin, B. Oxygen uptake during the first minutes of heavy muscular exercise. J Appl Physiol...1802-1814; 1986. 233. Linehan, JH; Haworth, ST; Nelin, LD; Krenz, GS; Dawson, CA. A Simple Distensible Vessel Model for Interpreting Pulmonary

An SNMP-based solution to enable remote ISO/IEEE 11073 technical management.

PubMed

Lasierra, Nelia; Alesanco, Alvaro; García, José

2012-07-01

This paper presents the design and implementation of an architecture based on the integration of simple network management protocol version 3 (SNMPv3) and the standard ISO/IEEE 11073 (X73) to manage technical information in home-based telemonitoring scenarios. This architecture includes the development of an SNMPv3-proxyX73 agent which comprises a management information base (MIB) module adapted to X73. In the proposed scenario, medical devices (MDs) send information to a concentrator device [designated as compute engine (CE)] using the X73 standard. This information together with extra information collected in the CE is stored in the developed MIB. Finally, the information collected is available for remote access via SNMP connection. Moreover, alarms and events can be configured by an external manager in order to provide warnings of irregularities in the MDs' technical performance evaluation. This proposed SNMPv3 agent provides a solution to integrate and unify technical device management in home-based telemonitoring scenarios fully adapted to X73.

Extended device profiles and testing procedures for the approval process of integrated medical devices using the IEEE 11073 communication standard.

PubMed

Janß, Armin; Thorn, Johannes; Schmitz, Malte; Mildner, Alexander; Dell'Anna-Pudlik, Jasmin; Leucker, Martin; Radermacher, Klaus

2018-02-23

Nowadays, only closed and proprietary integrated operating room systems (IORS) from big manufacturers are available on the market. Hence, the interconnection of components from third-party vendors is only possible with increased time and costs. In the context of the German Federal Ministry of Education and Research (BMBF)-funded project OR.NET (2012-2016), the open integration of medical devices from different manufacturers was addressed. An integrated operating theater based on the open communication standard IEEE 11073 shall give clinical operators the opportunity to choose medical devices independently of the manufacturer. This approach would be advantageous especially for hospital operators and small- and medium-sized enterprises (SME) of medical devices. Actual standards and concepts regarding technical feasibility and the approval process do not cope with the requirements for a modular integration of medical devices in the operating room (OR), based on an open communication standard. Therefore, innovative approval strategies and corresponding certification and test procedures, which cover actual legal and normative standards, have to be developed in order to support the future risk management and the usability engineering process of open integrated medical devices in the OR. The use of standardized device and service profiles and a three-step testing procedure, including conformity, interoperability and integration tests are described in this paper and shall support the manufacturers to integrate their medical devices without disclosing the medical devices' risk analysis and related confidential expertise or proprietary information.

Coexistence issues for a 2.4 GHz wireless audio streaming in presence of bluetooth paging and WLAN

NASA Astrophysics Data System (ADS)

Pfeiffer, F.; Rashwan, M.; Biebl, E.; Napholz, B.

2015-11-01

Nowadays, customers expect to integrate their mobile electronic devices (smartphones and laptops) in a vehicle to form a wireless network. Typically, IEEE 802.11 is used to provide a high-speed wireless local area network (WLAN) and Bluetooth is used for cable replacement applications in a wireless personal area network (PAN). In addition, Daimler uses KLEER as third wireless technology in the unlicensed (UL) 2.4 GHz-ISM-band to transmit full CD-quality digital audio. As Bluetooth, IEEE 802.11 and KLEER are operating in the same frequency band, it has to be ensured that all three technologies can be used simultaneously without interference. In this paper, we focus on the impact of Bluetooth and IEEE 802.11 as interferer in presence of a KLEER audio transmission.

Enabling Medical Device Interoperability for the Integrated Clinical Environment

DTIC Science & Technology

2016-02-01

Pajic M, Mangharam R, Sokolsky O, Arney D, Goldman JM, Lee I. Model-Driven Safety Analysis of Closed - Loop Medical Systems. IEEE Transactions on...Manigel J, Osborn D, Roellike T, Weininger S, Westenskow D, “Development of a Standard for Physiologic Closed Loop Controllers in Medical Devices...3 2010. 27. Arney D, Pajic M, Goldman JM, Lee I, Mangharam R, Sokolsky O, “Toward Patient Safety in Closed - Loop Medical Device Systems,” In

Clinical efficacy and effectiveness of 3D printing: a systematic review.

PubMed

Diment, Laura E; Thompson, Mark S; Bergmann, Jeroen H M

2017-12-21

To evaluate the clinical efficacy and effectiveness of using 3D printing to develop medical devices across all medical fields. Systematic review compliant with Preferred Reporting Items for Systematic Reviews and Meta-Analyses. PubMed, Web of Science, OVID, IEEE Xplore and Google Scholar. A double-blinded review method was used to select all abstracts up to January 2017 that reported on clinical trials of a three-dimensional (3D)-printed medical device. The studies were ranked according to their level of evidence, divided into medical fields based on the International Classification of Diseases chapter divisions and categorised into whether they were used for preoperative planning, aiding surgery or therapy. The Downs and Black Quality Index critical appraisal tool was used to assess the quality of reporting, external validity, risk of bias, risk of confounding and power of each study. Of the 3084 abstracts screened, 350 studies met the inclusion criteria. Oral and maxillofacial surgery contained 58.3% of studies, and 23.7% covered the musculoskeletal system. Only 21 studies were randomised controlled trials (RCTs), and all fitted within these two fields. The majority of RCTs were 3D-printed anatomical models for preoperative planning and guides for aiding surgery. The main benefits of these devices were decreased surgical operation times and increased surgical accuracy. All medical fields that assessed 3D-printed devices concluded that they were clinically effective. The fields that most rigorously assessed 3D-printed devices were oral and maxillofacial surgery and the musculoskeletal system, both of which concluded that the 3D-printed devices outperformed their conventional comparators. However, the efficacy and effectiveness of 3D-printed devices remain undetermined for the majority of medical fields. 3D-printed devices can play an important role in healthcare, but more rigorous and long-term assessments are needed to determine if 3D-printed devices are clinically relevant before they become part of standard clinical practice. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Device interoperability and authentication for telemedical appliance based on the ISO/IEEE 11073 Personal Health Device (PHD) Standards.

PubMed

Caranguian, Luther Paul R; Pancho-Festin, Susan; Sison, Luis G

2012-01-01

In this study, we focused on the interoperability and authentication of medical devices in the context of telemedical systems. A recent standard called the ISO/IEEE 11073 Personal Health Device (X73-PHD) Standards addresses the device interoperability problem by defining common protocols for agent (medical device) and manager (appliance) interface. The X73-PHD standard however has not addressed security and authentication of medical devices which is important in establishing integrity of a telemedical system. We have designed and implemented a security policy within the X73-PHD standards. The policy will enable device authentication using Asymmetric-Key Cryptography and the RSA algorithm as the digital signature scheme. We used two approaches for performing the digital signatures: direct software implementation and use of embedded security modules (ESM). The two approaches were evaluated and compared in terms of execution time and memory requirement. For the standard 2048-bit RSA, ESM calculates digital signatures only 12% of the total time for the direct implementation. Moreover, analysis shows that ESM offers more security advantage such as secure storage of keys compared to using direct implementation. Interoperability with other systems was verified by testing the system with LNI Healthlink, a manager software that implements the X73-PHD standard. Lastly, security analysis was done and the system's response to common attacks on authentication systems was analyzed and several measures were implemented to protect the system against them.

Insulator Charging in RF MEMS Capacitive Switches

DTIC Science & Technology

2005-06-01

and Simulations,” Journal of Microelectromechanical Systems, 8: 208-217 (June 1999). 5. Neaman , Donald. Semiconductor Physics & Devices. Boston...227-230 (2001). 5. Sze, S.M. Semiconductor Devices: Physics and Technology. New York: Wiley, 1985. 6. Neaman , Donald A. Semiconductor Physics...Radiation Response of Hafnium-Silicate Capacitors,” IEEE Transactions on Nuclear Science, 49: 3191-3196 (December 2002). 3. Neaman , D.A

GMAG Dissertation Award Talk: All Spin Logic -- Multimagnet Networks interacting via Spin currents

NASA Astrophysics Data System (ADS)

Srinivasan, Srikant

2012-02-01

Digital logic circuits have traditionally been based on storing information as charge on capacitors, and the stored information is transferred by controlling the flow of charge. However, electrons carry both charge and spin, the latter being responsible for magnetic phenomena. In the last few decades, there has been a significant improvement in our ability to control spins and their interaction with magnets. All Spin Logic (ASL) represents a new approach to information processing where spins and magnets now mirror the roles of charges and capacitors in conventional logic circuits. In this talk I first present a model [1] that couples non-collinear spin transport with magnet-dynamics to predict the switching behavior of the basic ASL device. This model is based on established physics and is benchmarked against available experimental data that demonstrate spin-torque switching in lateral structures. Next, the model is extended to simulate multi-magnet networks coupled with spin transport channels. The simulations suggest ASL devices have the essential characteristics for building logic circuits. In particular, (1) the example of an ASL ring oscillator [2, 3] is used to provide a clear signature of directed information transfer in cascaded ASL devices without the need for external control circuitry and (2) a simulated NAND [4] gate with fan-out of 2 suggests that ASL can implement universal logic and drive subsequent stages. Finally I will discuss how ASL based circuits could also have potential use in the design of neuromorphic circuits suitable for hybrid analog/digital information processing because of the natural mapping of ASL devices to neurons [4]. [4pt] [1] B. Behin-Aein, A. Sarkar, S. Srinivasan, and S. Datta, ``Switching Energy-Delay of All-Spin Logic devices,'' Appl. Phys. Lett., 98, 123510 (2011).[0pt] [2] S. Srinivasan, A. Sarkar, B. Behin-Aein, and S. Datta, ``All Spin Logic Device with Inbuilt Non-reciprocity,'' IEEE Trans. Magn., 47, 10 (2011).[0pt] [3] S. Srinivasan, A. Sarkar, B. Behin-Aein and S. Datta, ``Unidirectional Information transfer with cascaded All Spin Logic devices: A Ring Oscillator,'' IEEE Device Research Conference (2011).[0pt] [4] A. Sarkar, S. Srinivasan, B. Behin-Aein and S. Datta, ``Multimagnet networks interacting via spin currents'' IEEE International Electron Devices Meeting 2011. (to appear).

On the seamless, harmonized use of ISO/IEEE11073 and openEHR.

PubMed

Trigo, Jesús D; Kohl, Christian D; Eguzkiza, Aitor; Martínez-Espronceda, Miguel; Alesanco, Álvaro; Serrano, Luis; García, José; Knaup, Petra

2014-05-01

Standardized exchange of clinical information is a key factor in the provision of high quality health care systems. In this context, the openEHR specification facilitates the management of health data in electronic health records (EHRs), while the ISO/IEEE11073 (also referred to as X73PHD) family of standards provides a reference framework for medical device interoperability. Hospitals and health care providers using openEHR require flawless integration of data coming from external sources, such as X73PHD. Hence, a harmonization process is crucial for achieving a seamless, coherent use of those specifications in real scenarios. Such harmonization is the aim of this paper. Thus, the classes and attributes of a representative number of X73PHD specializations for medical devices--weight, temperature, blood pressure, pulse and heart rate, oximetry, and electrocardiograph--along with the X73PHD core document--ISO/IEEE11073-20601--have been analyzed and mapped to openEHR archetypes. The proposed methodology reuses the existing archetypes when possible and suggests new ones--or appropriate modifications--otherwise. As a result, this paper analyzes the inconsistencies found and the implications thereof in the coordinated use of these two standards. The procedure has also shown how existing standards are able to influence the archetype development process, enhancing the existing archetype corpus.

Wireless sensor network for wide-area high-mobility applications

NASA Astrophysics Data System (ADS)

del Castillo, Ignacio; Esper-Chaín, Roberto; Tobajas, Félix; de Armas, Valentín.

2013-05-01

In recent years, IEEE 802.15.4-based Wireless Sensor Networks (WSN) have experienced significant growth, mainly motivated by the standard features, such as small size oriented devices, low power consumption nodes, wireless communication links, and sensing and data processing capabilities. In this paper, the development, implementation and deployment of a novel fully compatible IEEE 802.15.4-based WSN architecture for applications operating over extended geographic regions with high node mobility support, is described. In addition, a practical system implementation of the proposed WSN architecture is presented and described for experimental validation and characterization purposes.

Demonstration of High-Mobility Electron and Hole Transport in a Single InGaSb Well for Complementary Circuits

DTIC Science & Technology

2009-01-01

Abrokwah, P.N. Parakh, T.D. Basso, S.M. Gold, S. Stetson, C.R. Gauthier, D. Foster, B. Crawforth, T. McQuire, K . Sakallah, R.J. Lomax, T.N. Mudge...IEEE Trans. VLSI Syst. 6 (1998) 47. [3] A. Leuther, A. Thiede, K . Kohler, T. Jakobus, G. Weimann, Compd. Semicond. 1999 (2000) 313. [4] J.H. Tsai, C.M...Longenbach, R. Beresford, W.I. Wang, IEEE Trans. Electron Devices 37 (1990) 2265. [8] K . Yoh, H. Taniguchi, K . Kiyomi, M. Inoue, Jpn. J. Appl. Phys. I 30

Using RF-DNA Fingerprints to Discriminate ZigBee Devices in an Operational Environment

DTIC Science & Technology

2013-03-01

network keys and Media Access Control (MAC) lists which can be subverted through interception and spoofing using open-source hacking tools. This work...for Mobile Communication (GSM) cellular phones [40, 47], IEEE 802.11 WiFi [21, 23, 24, 28, 29, 35, 42], and IEEE 802.16 WiMAX [34, 35, 37, 38, 48...802.11a WiFi × [21, 28–30, 35, 48] GSM Cellular × [39, 40, 47] 802.16e WiMax × [34, 35, 38, 48] 802.15.4 ZigBee × [31] × [11, 12] Classifier Type MDA/ML

A Novel IEEE 802.15.4e DSME MAC for Wireless Sensor Networks

PubMed Central

Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

2017-01-01

IEEE 802.15.4e standard proposes Deterministic and Synchronous Multichannel Extension (DSME) mode for wireless sensor networks (WSNs) to support industrial, commercial and health care applications. In this paper, a new channel access scheme and beacon scheduling schemes are designed for the IEEE 802.15.4e enabled WSNs in star topology to reduce the network discovery time and energy consumption. In addition, a new dynamic guaranteed retransmission slot allocation scheme is designed for devices with the failure Guaranteed Time Slot (GTS) transmission to reduce the retransmission delay. To evaluate our schemes, analytical models are designed to analyze the performance of WSNs in terms of reliability, delay, throughput and energy consumption. Our schemes are validated with simulation and analytical results and are observed that simulation results well match with the analytical one. The evaluated results of our designed schemes can improve the reliability, throughput, delay, and energy consumptions significantly. PMID:28275216

A Novel IEEE 802.15.4e DSME MAC for Wireless Sensor Networks.

PubMed

Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

2017-01-16

IEEE 802.15.4e standard proposes Deterministic and Synchronous Multichannel Extension (DSME) mode for wireless sensor networks (WSNs) to support industrial, commercial and health care applications. In this paper, a new channel access scheme and beacon scheduling schemes are designed for the IEEE 802.15.4e enabled WSNs in star topology to reduce the network discovery time and energy consumption. In addition, a new dynamic guaranteed retransmission slot allocation scheme is designed for devices with the failure Guaranteed Time Slot (GTS) transmission to reduce the retransmission delay. To evaluate our schemes, analytical models are designed to analyze the performance of WSNs in terms of reliability, delay, throughput and energy consumption. Our schemes are validated with simulation and analytical results and are observed that simulation results well match with the analytical one. The evaluated results of our designed schemes can improve the reliability, throughput, delay, and energy consumptions significantly.

Challenges and Opportunities for Biophotonic Devices in the Liquid State and the Solid State

DTIC Science & Technology

2006-07-01

of the NPB:Eu device and a baseline device (without the NPB layer and emitting from the Alq3 layer) as a function of current density. The luminance...of the NPB:Eu device is clearly superior, with a maximum of 590 cd/m2 at 375 mA/cm2, whereas the Alq3 OLED peaks at only 45 cd/m2 at 30 mA/cm2...Luminance versus current density for Eu-doped BioLED and for baseline Alq3 device. 1-4244-0078-3/06/$20.00 (c) 2006 IEEE B. Electrofluidic

Integrated Nano Optoplasmonics (NBIT Phase 2)

DTIC Science & Technology

2013-12-16

of-principle realization demonstrates the potential of integrated plasmonic devices in quantum information processing and cryptography ...photonic/plasmonic devices that are made of nanoscale photonic/plasmonic cavities coupled to quantum emitters, and (2) fabrication of electrically...publications in leading journals (one in Phys. Rev. Lett.,1 one in IEEE J. Sel. Topics Quantum Electron.2 and three publications in Nano Lett.3,4,5) and one

An IEEE802.15.4-Based System for Locating Children on Their School Commutes

NASA Astrophysics Data System (ADS)

Sugiura, Akihiko; Baba, Ryoichi; Kobayashi, Hideyuki

With the increasing number of crimes and accidents in which children are becoming involved, there is a growing demand for devices to safeguard children's security by detecting their locations on their way to and from school. This paper proposes a system that uses an IEEE802.15.4-standard network to detect children's locations. To overcome the susceptibility of radio interference from nearby wireless LANs, frequency division multiplexing is applied to this IEEE802.15.4-based network, toward improving data acquisition from terminal units. The effectiveness of the system was field-tested with elementary school students who used about 400 IEEE 802.15.4-compliant terminal units. An experiment verified that the use of frequency division multiplexing in an environment where radio interference by wireless LANs is strong allowed the network to double the success rate of information communication from terminal units relative to that without frequency division multiplexing. In the experiment for detecting elementary schoolers' arrival at and departure from school, the terminal detection rate was 99% and the terminal detection rate on the designated school routes was 90%. These results prove the effectiveness of the system in detecting locations.

47 CFR 2.1093 - Radiofrequency radiation exposure evaluation: portable devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Electromagnetic Fields, 3 kHz to 300 GHz,” ANSI/IEEE C95.1-1992, Copyright 1992 by the Institute of Electrical and... Exposure Criteria for Radiofrequency Electromagnetic Fields,” NCRP Report No. 86, Section 17.4.5. Copyright...

The ac power line protection for an IEEE 587 Class B environment

NASA Technical Reports Server (NTRS)

Roehr, W. D.; Clark, O. M.

1984-01-01

The 587B series of protectors are unique, low clamping voltage transient suppressors to protect ac-powered equipment from the 6000V peak open-circuit voltage and 3000A short circuit current as defined in IEEE standard 587 for Category B transients. The devices, which incorporate multiple-stage solid-state protector components, were specifically designed to operate under multiple exposures to maximum threat levels in this severe environment. The output voltage peaks are limited to 350V under maximum threat conditions for a 120V ac power line, thus providing adequate protection to vulnerable electronic equipment. The principle of operation and test performance data is discussed.

A comparison between the ANSI/IEEE and the CENELEC/IEC approach to overload protection of insulated power cables

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parise, G.; Rubino, G.

1995-12-31

The same basic principles, on which the methods of power cables protection against overloads are based, are summed up by different criteria and formulations within ANSI/IEEE and CENELEC/IEC publications. The studies carried out by the technical committees of these organizations have been examined and compared in order to point out not only their differences but also their complementary aspects. By arranging the two approaches, it has been possible to outline a third way to determine the admissible duration of overload currents and define intermediate criteria for the emergency ratings of cables and for the coordination of protective devices.

Risk Assessment of Power System considering the CPS of Transformers

NASA Astrophysics Data System (ADS)

Zhou, Long; Peng, Zewu; Liu, Xindong; Li, Canbing; Chen, Can

2018-02-01

This paper constructs a risk assessment framework of power system for device-level information security, analyzes the typical protection configuration of power transformers, and takes transformer gas protection and differential protection as examples to put forward a method that analyzes the cyber security in electric power system, which targets transformer protection parameters. We estimate the risk of power system accounting for the cyber security of transformer through utilizing Monte Carlo method and two indexes, which are the loss of load probability and the expected demand not supplied. The proposed approach is tested with IEEE 9 bus system and IEEE 118 bus system.

Atomic Layer Deposition of Al2O3 on GaSb Using In Situ Hydrogen Plasma Exposure

DTIC Science & Technology

2012-12-03

Krishna, and A. Javey, Nano Lett. 12, 3592 (2012). 7A. Ali, H. Madan , A. Agrawal, I. Ramirez, R. Misra, J. B. Boos, B. R. Bennett, J. Lindemuth, and S...Trans. Electron Devices 58, 3407 (2011). 9M. Xu, R. S. Wang, and P. D. Ye, IEEE Electron Device Lett. 32, 883 (2011). 10A. Ali, H. S. Madan , A. P. Kirk

Hardware Timestamping for an Image Acquisition System Based on FlexRIO and IEEE 1588 v2 Standard

NASA Astrophysics Data System (ADS)

Esquembri, S.; Sanz, D.; Barrera, E.; Ruiz, M.; Bustos, A.; Vega, J.; Castro, R.

2016-02-01

Current fusion devices usually implement distributed acquisition systems for the multiple diagnostics of their experiments. However, each diagnostic is composed by hundreds or even thousands of signals, including images from the vessel interior. These signals and images must be correctly timestamped, because all the information will be analyzed to identify plasma behavior using temporal correlations. For acquisition devices without synchronization mechanisms the timestamp is given by another device with timing capabilities when signaled by the first device. Later, each data should be related with its timestamp, usually via software. This critical action is unfeasible for software applications when sampling rates are high. In order to solve this problem this paper presents the implementation of an image acquisition system with real-time hardware timestamping mechanism. This is synchronized with a master clock using the IEEE 1588 v2 Precision Time Protocol (PTP). Synchronization, image acquisition and processing, and timestamping mechanisms are implemented using Field Programmable Gate Array (FPGA) and a timing card -PTP v2 synchronized. The system has been validated using a camera simulator streaming videos from fusion databases. The developed architecture is fully compatible with ITER Fast Controllers and has been integrated with EPICS to control and monitor the whole system.

49 CFR 501.2 - General.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (2) Chapter 303—National Driver Register. (3) Chapter 305—National Automobile Title Information.... (7) Chapter 327—Odometers. (8) Chapter 329—Automobile Fuel Economy. (9) Chapter 331—Theft Prevention... and maintenance, traffic control devices, identification and surveillance of accident locations, and...

49 CFR 501.2 - General.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (2) Chapter 303—National Driver Register. (3) Chapter 305—National Automobile Title Information.... (7) Chapter 327—Odometers. (8) Chapter 329—Automobile Fuel Economy. (9) Chapter 331—Theft Prevention... and maintenance, traffic control devices, identification and surveillance of accident locations, and...

Personal Information Search on Mobile Devices

DTIC Science & Technology

2007-09-01

Networking .....................28 a. Bluetooth ...............................28 b. Infrared ................................29 2. Mobile Data...Also in this chapter, the connection techniques and schemes including Bluetooth , GPRS, Wi-Fi will be discussed. Chapter IV is devoted to a...characteristics of mobile devices. Recent advances in networking technologies such as 802.11 and Bluetooth enable these new mobile devices to connect to

Modeling and Design of GaN High Electron Mobility Transistors and Hot Electron Transistors through Monte Carlo Particle-based Device Simulations

NASA Astrophysics Data System (ADS)

Soligo, Riccardo

In this work, the insight provided by our sophisticated Full Band Monte Carlo simulator is used to analyze the behavior of state-of-art devices like GaN High Electron Mobility Transistors and Hot Electron Transistors. Chapter 1 is dedicated to the description of the simulation tool used to obtain the results shown in this work. Moreover, a separate section is dedicated the set up of a procedure to validate to the tunneling algorithm recently implemented in the simulator. Chapter 2 introduces High Electron Mobility Transistors (HEMTs), state-of-art devices characterized by highly non linear transport phenomena that require the use of advanced simulation methods. The techniques for device modeling are described applied to a recent GaN-HEMT, and they are validated with experimental measurements. The main techniques characterization techniques are also described, including the original contribution provided by this work. Chapter 3 focuses on a popular technique to enhance HEMTs performance: the down-scaling of the device dimensions. In particular, this chapter is dedicated to lateral scaling and the calculation of a limiting cutoff frequency for a device of vanishing length. Finally, Chapter 4 and Chapter 5 describe the modeling of Hot Electron Transistors (HETs). The simulation approach is validated by matching the current characteristics with the experimental one before variations of the layouts are proposed to increase the current gain to values suitable for amplification. The frequency response of these layouts is calculated, and modeled by a small signal circuit. For this purpose, a method to directly calculate the capacitance is developed which provides a graphical picture of the capacitative phenomena that limit the frequency response in devices. In Chapter 5 the properties of the hot electrons are investigated for different injection energies, which are obtained by changing the layout of the emitter barrier. Moreover, the large signal characterization of the HET is shown for different layouts, where the collector barrier was scaled.

An energy-efficient transmission scheme for real-time data in wireless sensor networks.

PubMed

Kim, Jin-Woo; Barrado, José Ramón Ramos; Jeon, Dong-Keun

2015-05-20

The Internet of things (IoT) is a novel paradigm where all things or objects in daily life can communicate with other devices and provide services over the Internet. Things or objects need identifying, sensing, networking and processing capabilities to make the IoT paradigm a reality. The IEEE 802.15.4 standard is one of the main communication protocols proposed for the IoT. The IEEE 802.15.4 standard provides the guaranteed time slot (GTS) mechanism that supports the quality of service (QoS) for the real-time data transmission. In spite of some QoS features in IEEE 802.15.4 standard, the problem of end-to-end delay still remains. In order to solve this problem, we propose a cooperative medium access scheme (MAC) protocol for real-time data transmission. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the network performance.

An Energy-Efficient Transmission Scheme for Real-Time Data in Wireless Sensor Networks

PubMed Central

Kim, Jin-Woo; Barrado, José Ramón Ramos; Jeon, Dong-Keun

2015-01-01

The Internet of things (IoT) is a novel paradigm where all things or objects in daily life can communicate with other devices and provide services over the Internet. Things or objects need identifying, sensing, networking and processing capabilities to make the IoT paradigm a reality. The IEEE 802.15.4 standard is one of the main communication protocols proposed for the IoT. The IEEE 802.15.4 standard provides the guaranteed time slot (GTS) mechanism that supports the quality of service (QoS) for the real-time data transmission. In spite of some QoS features in IEEE 802.15.4 standard, the problem of end-to-end delay still remains. In order to solve this problem, we propose a cooperative medium access scheme (MAC) protocol for real-time data transmission. We also evaluate the performance of the proposed scheme through simulation. The simulation results demonstrate that the proposed scheme can improve the network performance. PMID:26007722

A Green Media Access Method for IEEE 802.15.6 Wireless Body Area Network.

PubMed

Jacob, Anil K; Jacob, Lillykutty

2017-09-30

It is of utmost importance to conserve battery energy to the maximum possible extent in WBAN nodes while collecting and transferring medical data. The IEEE 802.15.6 WBAN standard does not specify any method to conserve energy. This paper focuses on a method to conserve energy in IEEE 802.15.6 WBAN nodes when using CSMA/CA, while simultaneously restricting data delivery delay to the required value as specified in medical applications. The technique is to allow the nodes to sleep all the times except for receiving beacons and for transmitting data frames whenever a data frame enters an empty buffer. The energy consumed by the nodes and the average latency of data frame for periodical arrival of data are found out analytically. The analytical results are validated and also the proposed method is compared with other energy conserving schemes, using Castalia simulation studies. The proposed method shows superior performance in both device lifetime and latency of emergency medical data.

David S. Ginley | NREL

Science.gov Websites

is on the development of new nanomaterials for organic electronics and as biofilters etc. Dr are applying what they learn to improved devices, i.e. batteries, frequency agile electronics Society (ECS) Institute of Electrical and Electronics Engineers (IEEE) American Association for the

IEEE WMED 2016 Homepage

Science.gov Websites

characterization, design, and new device technologies. This workshop will consist of invited talks, contributed and Reliability Semiconductor package reliability, Design for Manufacturability, Stacked die packaging and Novel assembly processes Microelectronic Circuit Design New product design, high-speed and/or low

Local Area Networks: Part I.

ERIC Educational Resources Information Center

Dessy, Raymond E.

1982-01-01

Local area networks are common communication conduits allowing various terminals, computers, discs, printers, and other electronic devices to intercommunicate over short distances. Discusses the vocabulary of such networks including RS-232C point-to-point and IEEE-488 multidrop protocols; error detection; message packets; multiplexing; star, ring,…

A Reliable Data Transmission Model for IEEE 802.15.4e Enabled Wireless Sensor Network under WiFi Interference.

PubMed

Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

2017-06-07

The IEEE 802.15.4e standard proposes Medium Access Control (MAC) to support collision-free wireless channel access mechanisms for industrial, commercial and healthcare applications. However, unnecessary wastage of energy and bandwidth consumption occur due to inefficient backoff management and collisions. In this paper, a new channel access mechanism is designed for the buffer constraint sensor devices to reduce the packet drop rate, energy consumption and collisions. In order to avoid collision due to the hidden terminal problem, a new frame structure is designed for the data transmission. A new superframe structure is proposed to mitigate the problems due to WiFi and ZigBee interference. A modified superframe structure with a new retransmission opportunity for failure devices is proposed to reduce the collisions and retransmission delay with high reliability. Performance evaluation and validation of our scheme indicate that the packet drop rate, throughput, reliability, energy consumption and average delay of the nodes can be improved significantly.

An Enhanced Reservation-Based MAC Protocol for IEEE 802.15.4 Networks

PubMed Central

Afonso, José A.; Silva, Helder D.; Macedo, Pedro; Rocha, Luis A.

2011-01-01

The IEEE 802.15.4 Medium Access Control (MAC) protocol is an enabling standard for wireless sensor networks. In order to support applications requiring dedicated bandwidth or bounded delay, it provides a reservation-based scheme named Guaranteed Time Slot (GTS). However, the GTS scheme presents some drawbacks, such as inefficient bandwidth utilization and support to a maximum of only seven devices. This paper presents eLPRT (enhanced Low Power Real Time), a new reservation-based MAC protocol that introduces several performance enhancing features in comparison to the GTS scheme. This MAC protocol builds on top of LPRT (Low Power Real Time) and includes various mechanisms designed to increase data transmission reliability against channel errors, improve bandwidth utilization and increase the number of supported devices. A motion capture system based on inertial and magnetic sensors has been used to validate the protocol. The effectiveness of the performance enhancements introduced by each of the new features is demonstrated through the provision of both simulation and experimental results. PMID:22163826

Trustworthy data collection from implantable medical devices via high-speed security implementation based on IEEE 1363.

PubMed

Hu, Fei; Hao, Qi; Lukowiak, Marcin; Sun, Qingquan; Wilhelm, Kyle; Radziszowski, Stanisław; Wu, Yao

2010-11-01

Implantable medical devices (IMDs) have played an important role in many medical fields. Any failure in IMDs operations could cause serious consequences and it is important to protect the IMDs access from unauthenticated access. This study investigates secure IMD data collection within a telehealthcare [mobile health (m-health)] network. We use medical sensors carried by patients to securely access IMD data and perform secure sensor-to-sensor communications between patients to relay the IMD data to a remote doctor's server. To meet the requirements on low computational complexity, we choose N-th degree truncated polynomial ring (NTRU)-based encryption/decryption to secure IMD-sensor and sensor-sensor communications. An extended matryoshkas model is developed to estimate direct/indirect trust relationship among sensors. An NTRU hardware implementation in very large integrated circuit hardware description language is studied based on industry Standard IEEE 1363 to increase the speed of key generation. The performance analysis results demonstrate the security robustness of the proposed IMD data access trust model.

Implementation experiences of ISO/IEEE11073 standard applied to new use cases for e-health environments.

PubMed

Martinez, I; Escayola, J; Martinez-Espronceda, M; Serrano, L; Trigo, J D; Led, S; Garcia, J

2009-01-01

Recent advances in biomedical engineering and continuous technological innovations in last decade are promoting new challenges, especially in e-Health environments. In this context, the medical devices interoperability is one of the interest fields wherein these improvements require a standard-based design in order to achieve homogeneous solutions. Furthermore, the spreading of wearable devices, oriented to the paradigm of patient environment and supported by wireless technologies as Bluetooth or ZigBee, is bringing new medical use cases based on Ambient Assisted Living, home monitoring of elderly, heart failure, chronic, under palliative care or patients who have undergone surgery, urgencies and emergencies, or even fitness auto-control and health follow-up. In this paper, several implementation experiences based on ISO/IEEE11073 standard are detailed. These evolved e-Health services can improve the quality of the patient's care, increase the user's interaction, and assure these e-Health applications to be fully compatible with global telemedicine systems.

A Reliable Data Transmission Model for IEEE 802.15.4e Enabled Wireless Sensor Network under WiFi Interference

PubMed Central

Sahoo, Prasan Kumar; Pattanaik, Sudhir Ranjan; Wu, Shih-Lin

2017-01-01

The IEEE 802.15.4e standard proposes Medium Access Control (MAC) to support collision-free wireless channel access mechanisms for industrial, commercial and healthcare applications. However, unnecessary wastage of energy and bandwidth consumption occur due to inefficient backoff management and collisions. In this paper, a new channel access mechanism is designed for the buffer constraint sensor devices to reduce the packet drop rate, energy consumption and collisions. In order to avoid collision due to the hidden terminal problem, a new frame structure is designed for the data transmission. A new superframe structure is proposed to mitigate the problems due to WiFi and ZigBee interference. A modified superframe structure with a new retransmission opportunity for failure devices is proposed to reduce the collisions and retransmission delay with high reliability. Performance evaluation and validation of our scheme indicate that the packet drop rate, throughput, reliability, energy consumption and average delay of the nodes can be improved significantly. PMID:28590434

Coordinated Control Method of Voltage and Reactive Power for Active Distribution Networks Based on Soft Open Point

DOE PAGES

Li, Peng; Ji, Haoran; Wang, Chengshan; ...

2017-03-22

The increasing penetration of distributed generators (DGs) exacerbates the risk of voltage violations in active distribution networks (ADNs). The conventional voltage regulation devices limited by the physical constraints are difficult to meet the requirement of real-time voltage and VAR control (VVC) with high precision when DGs fluctuate frequently. But, soft open point (SOP), a flexible power electronic device, can be used as the continuous reactive power source to realize the fast voltage regulation. Considering the cooperation of SOP and multiple regulation devices, this paper proposes a coordinated VVC method based on SOP for ADNs. Firstly, a time-series model of coordi-natedmore » VVC is developed to minimize operation costs and eliminate voltage violations of ADNs. Then, by applying the linearization and conic relaxation, the original nonconvex mixed-integer non-linear optimization model is converted into a mixed-integer second-order cone programming (MISOCP) model which can be efficiently solved to meet the requirement of voltage regulation rapidity. Here, we carried out some case studies on the IEEE 33-node system and IEEE 123-node system to illustrate the effectiveness of the proposed method.« less

Coordinated Control Method of Voltage and Reactive Power for Active Distribution Networks Based on Soft Open Point

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Peng; Ji, Haoran; Wang, Chengshan

The increasing penetration of distributed generators (DGs) exacerbates the risk of voltage violations in active distribution networks (ADNs). The conventional voltage regulation devices limited by the physical constraints are difficult to meet the requirement of real-time voltage and VAR control (VVC) with high precision when DGs fluctuate frequently. But, soft open point (SOP), a flexible power electronic device, can be used as the continuous reactive power source to realize the fast voltage regulation. Considering the cooperation of SOP and multiple regulation devices, this paper proposes a coordinated VVC method based on SOP for ADNs. Firstly, a time-series model of coordi-natedmore » VVC is developed to minimize operation costs and eliminate voltage violations of ADNs. Then, by applying the linearization and conic relaxation, the original nonconvex mixed-integer non-linear optimization model is converted into a mixed-integer second-order cone programming (MISOCP) model which can be efficiently solved to meet the requirement of voltage regulation rapidity. Here, we carried out some case studies on the IEEE 33-node system and IEEE 123-node system to illustrate the effectiveness of the proposed method.« less

Exploration of high harmonic fast wave heating on the National Spherical Torus Experiment

NASA Astrophysics Data System (ADS)

Wilson, J. R.; Bell, R. E.; Bernabei, S.; Bitter, M.; Bonoli, P.; Gates, D.; Hosea, J.; LeBlanc, B.; Mau, T. K.; Medley, S.; Menard, J.; Mueller, D.; Ono, M.; Phillips, C. K.; Pinsker, R. I.; Raman, R.; Rosenberg, A.; Ryan, P.; Sabbagh, S.; Stutman, D.; Swain, D.; Takase, Y.; Wilgen, J.

2003-05-01

High harmonic fast wave (HHFW) heating has been proposed as a particularly attractive means for plasma heating and current drive in the high beta plasmas that are achievable in spherical torus (ST) devices. The National Spherical Torus Experiment (NSTX) [M. Ono, S. M. Kaye, S. Neumeyer et al., in Proceedings of the 18th IEEE/NPSS Symposium on Fusion Engineering, Albuquerque, 1999 (IEEE, Piscataway, NJ, 1999), p. 53] is such a device. An rf heating system has been installed on the NSTX to explore the physics of HHFW heating, current drive via rf waves and for use as a tool to demonstrate the attractiveness of the ST concept as a fusion device. To date, experiments have demonstrated many of the theoretical predictions for HHFW. In particular, strong wave absorption on electrons over a wide range of plasma parameters and wave parallel phase velocities, wave acceleration of energetic ions, and indications of current drive for directed wave spectra have been observed. In addition HHFW heating has been used to explore the energy transport properties of NSTX plasmas, to create H-mode discharges with a large fraction of bootstrap current and to control the plasma current profile during the early stages of the discharge.

Center for High-Frequency Microelectronics

DTIC Science & Technology

1992-08-31

34 IEEE Transactions on Electron Devices, 38, No. 6, pp. 1324-1333, June 1991. 185. C. C. Chen, R. K. Mains and G. I. Haddad, " High - Power Generation in...Weiss, J. Hu and W.-P. Hong, "Electronic 0 Properties of Power High Electron Mobility Transistors," Conference on Ballistic Electrons for Transistors...method at higher frequencies than previously believed. - Calculations of high - power generation modes in Si IMPATT devices in the 100-200 GHz range have

Technical Standards for Command and Control Information Systems (CCISs)

DTIC Science & Technology

1992-01-01

initiation, Conformance Testing 149 management, scheduling, resource allocation , logical and IEEE P1 003 146 physical device access, interrupt handling...70 5.2.3 Remote Data Access (RDA) ........................................... 72 5.2.4 Information Resource Dictionary...146 7.2.1.2 POSIX Conformance Testing .............................. 149 7.2.2 Consortia Recommendations

Device-Enabled Authorization in the Grey System

DTIC Science & Technology

2005-02-01

proof checker. Journal of Automated Reasoning 31(3-4):231–260, 2003. [7] D. Balfanz , D. Dean, and M. Spreitzer. A security infrastructure for...distributed Java applications. In Proceedings of the 21st IEEE Symposium on Security and Privacy, May 2002. [8] D. Balfanz and E. Felten. Hand-held computers

Reduced Graphene Oxide Molecular Sensors

DTIC Science & Technology

2008-01-01

sensors. When chemical sensor performance is considered, there are two important parameters . As discussed above, one of these parameters is the...Nano Lett. 2006, 6 (5), 930–936. (18) Hooge , F. N. IEEE Trans. Electron DeVices 1994, 41, 1926. (19) Lin, Y.-M.; Avouris, P. Nano Lett. 2008, 8 (8

Overview of Device SEE Susceptibility from Heavy Ions

NASA Technical Reports Server (NTRS)

Nichols, D. K.; Coss, J. R.; McCarthy, K. P.; Schwartz, H. R.; Smith, L. S.

1998-01-01

A fifth set of heavy ion single event effects (SEE) test data have been collected since the last IEEE publications (1,2,3,4) in December issues for 1985, 1987, 1989, and 1991. Trends in SEE susceptibility (including soft errors and latchup) for state-of-the-art parts are evaluated.

47 CFR 2.1093 - Radiofrequency radiation exposure evaluation: portable devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Cellular Radiotelephone Service pursuant to part 22 of this chapter; the Personal Communications Service (PCS) pursuant to part 24 of this chapter; the Satellite Communications Services pursuant to part 25 of this chapter; the Miscellaneous Wireless Communications Services pursuant to part 27 of this chapter...

Application of PSAT to Load Flow Analysis with STATCOM under Load Increase Scenario and Line Contingencies

NASA Astrophysics Data System (ADS)

Telang, Aparna S.; Bedekar, P. P.

2017-09-01

Load flow analysis is the initial and essential step for any power system computation. It is required for choosing better options for power system expansion to meet with ever increasing load demand. Implementation of Flexible AC Transmission System (FACTS) device like STATCOM, in the load flow, which is having fast and very flexible control, is one of the important tasks for power system researchers. This paper presents a simple and systematic approach for steady state power flow calculations with FACTS controller, static synchronous compensator (STATCOM) using command line usage of MATLAB tool-power system analysis toolbox (PSAT). The complexity of MATLAB language programming increases due to incorporation of STATCOM in an existing Newton-Raphson load flow algorithm. Thus, the main contribution of this paper is to show how command line usage of user friendly MATLAB tool, PSAT, can extensively be used for quicker and wider interpretation of the results of load flow with STATCOM. The novelty of this paper lies in the method of applying the load increase pattern, where the active and reactive loads have been changed simultaneously at all the load buses under consideration for creating stressed conditions for load flow analysis with STATCOM. The performance have been evaluated on many standard IEEE test systems and the results for standard IEEE-30 bus system, IEEE-57 bus system, and IEEE-118 bus system are presented.

An Updated Perspective of Single Event Gate Rupture and Single Event Burnout in Power MOSFETs

NASA Astrophysics Data System (ADS)

Titus, Jeffrey L.

2013-06-01

Studies over the past 25 years have shown that heavy ions can trigger catastrophic failure modes in power MOSFETs [e.g., single-event gate rupture (SEGR) and single-event burnout (SEB)]. In 1996, two papers were published in a special issue of the IEEE Transaction on Nuclear Science [Johnson, Palau, Dachs, Galloway and Schrimpf, “A Review of the Techniques Used for Modeling Single-Event Effects in Power MOSFETs,” IEEE Trans. Nucl. Sci., vol. 43, no. 2, pp. 546-560, April. 1996], [Titus and Wheatley, “Experimental Studies of Single-Event Gate Rupture and Burnout in Vertical Power MOSFETs,” IEEE Trans. Nucl. Sci., vol. 43, no. 2, pp. 533-545, Apr. 1996]. Those two papers continue to provide excellent information and references with regard to SEB and SEGR in vertical planar MOSFETs. This paper provides updated references/information and provides an updated perspective of SEB and SEGR in vertical planar MOSFETs as well as provides references/information to other device types that exhibit SEB and SEGR effects.

47 CFR 15.201 - Equipment authorization requirement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Section 15.201 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES... shall be verified pursuant to the procedures in Subpart J of part 2 of this chapter prior to marketing... pursuant to the procedures in subpart J of part 2 of this chapter prior to marketing. (c) For devices such...

Simulation Modeling and Analysis of Device-Aware Network Architectures

DTIC Science & Technology

2004-12-01

However, a potential issue lies in the location of the intermediate proxy with respect to the content servers; if the proxy is far away from the...to 11 guide the adaptation of content presented to that device [CC/PP, 2004]. The strength of CC/PP lies in its flexibility. CC/PP is based on RDF...from: http://ieeexplore.ieee.org/iel4/98/15881/00736473.pdf. Accessed October 2004. [Hu and Bagga, 2004] Jianying Hu and Amit Bagga, “Categorizing

Letters: Comment on "Effects of multi-scattering on the performance of a single-beam acoustic manipulation device".

PubMed

Mitri, F G

2013-11-01

The concern addressed in the present commentary is to point out the omission of the azimuthal component Fφ of the axial acoustic radiation force provided in M. Azarpeyvand, M. A. Alibakhshi, R. Self, "Effects of multi-scattering on the performance of a single-beam acoustic manipulation device," IEEE Trans. Ultrason. Ferroelectr. Freq. Control, vol. 59, no. 8, pp. 1741-1749, 2012, which may suggest a miscalculation of the radiation force function Ym and its related numerical computations.

Nonlinear Properties in Langasite Isomorphs for Advanced Frequency Control Devices and Clocks

DTIC Science & Technology

2006-11-01

or LGN), and langatate (La3Ga5.5Ta0.5O14 or LGT), have emerged as new materials to replace quartz in advanced frequency control devices and clocks...application and of angle Ψ. Fig. 1. Langatate boule (photo courtesy of the Univ. Central Florida) and typical resonators for testing. Table 1...langanite and y-cut langatate ,” IEEE Tr. Ultrason. Ferroelec. Freq. Contr., pp. 1678-1682, 2003. Kim, Y., “Amplitude-frequency effect of Y-cut langanite

21 CFR 20.100 - Applicability; cross-reference to other regulations.

Code of Federal Regulations, 2011 CFR

2011-04-01

... of this chapter. (25) Cosmetic establishment registrations, in § 710.7 of this chapter. (26) Cosmetic product ingredient and cosmetic raw material composition statements, § 720.8 of this chapter. (27) Cosmetic product experience reports, in § 730.7 of this chapter. (28) Device premarket notification...

21 CFR 20.100 - Applicability; cross-reference to other regulations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of this chapter. (25) Cosmetic establishment registrations, in § 710.7 of this chapter. (26) Cosmetic product ingredient and cosmetic raw material composition statements, § 720.8 of this chapter. (27) Cosmetic product experience reports, in § 730.7 of this chapter. (28) Device premarket notification...

Exploration of High Harmonic Fast Wave Heating on the National Spherical Torus Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.R. Wilson; R.E. Bell; S. Bernabei

2003-02-11

High Harmonic Fast Wave (HHFW) heating has been proposed as a particularly attractive means for plasma heating and current drive in the high-beta plasmas that are achievable in spherical torus (ST) devices. The National Spherical Torus Experiment (NSTX) [Ono, M., Kaye, S.M., Neumeyer, S., et al., Proceedings, 18th IEEE/NPSS Symposium on Fusion Engineering, Albuquerque, 1999, (IEEE, Piscataway, NJ (1999), p. 53.)] is such a device. An radio-frequency (rf) heating system has been installed on NSTX to explore the physics of HHFW heating, current drive via rf waves and for use as a tool to demonstrate the attractiveness of the STmore » concept as a fusion device. To date, experiments have demonstrated many of the theoretical predictions for HHFW. In particular, strong wave absorption on electrons over a wide range of plasma parameters and wave parallel phase velocities, wave acceleration of energetic ions, and indications of current drive for directed wave spectra have been observed. In addition HHFW heating has been used to explore the energy transport properties of NSTX plasmas, to create H-mode (high-confinement mode) discharges with a large fraction of bootstrap current and to control the plasma current profile during the early stages of the discharge.« less

Developing Secure Agent Systems Using Delegation Based Trust Management

DTIC Science & Technology

2005-01-01

delegation rules, so that the information in the SCM may be accessed only by authorized agents. Special intelligent agents called security agents are re... Bluetooth , IEEE 802.11, or Infrared, via any hand-held device, within a Vigil can also be used in wired systems, but the focal point of our re- search is

Nanophotonic Devices - Spontaneous Emission Faster than Stimulated Emission

DTIC Science & Technology

2014-11-04

2010 Granada Spain PECS IX "The Two Conflicting Narratives of Metal-Optics" Aug. 17, 2010 Seoul Korea IEEE Nano Korea Symposium "The Two...Two Conflicting Narratives of Metal-Optics" Sept. 28, 2010 Granada Spain PECS IX "The Two Conflicting Narratives of Metal-Optics" Aug. 17, 2010

Fundamental Issues in Space Electronics Reliability: Negative Bias Temperature Instability

DTIC Science & Technology

2010-12-01

Mintarno, S. Mitra, S. Krishnan, Y. Cao, “Circuit Aging Prediction for Low-Power Operation,” Proc. IEEE/CICC (2009) [7] D. A Neaman , Semiconductor Physics...dielectric based field effect transistors,” J. Appl. Phys. 104 124109 (2008) [6] D. A Neaman , Semiconductor Physics and Devices, NY: McGraw Hill

DURIP: Mitigating Attacks on Mobile Devices and Critical Cellular Infrastructure

DTIC Science & Technology

2016-03-03

Patrick Traynor, Shobha Venkataraman . Why is my smartphone slow? On the fly diagnosis of underperformance on the mobile Internet, 2013 43rd Annual IEEE...Symposium (NDSS), 2013. 4. C. Amrutkar, M. Hiltunen, T. Jim, K. Joshi, O. Spatscheck, P. Traynor and S. Venkataraman , Why is My Smartphone Slow? On The

47 CFR 2.1093 - Radiofrequency radiation exposure evaluation: portable devices.

Code of Federal Regulations, 2012 CFR

2012-10-01

... for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to... Exposure Criteria for Radiofrequency Electromagnetic Fields,” NCRP Report No. 86, Section 17.4.5. Copyright... Electromagnetic Fields—RF and Microwave,” IEEE C95.3-1991. (4) For purposes of analyzing portable transmitting...

Growth, Characterization and Device Development in Monocrystalline Diamond Films

DTIC Science & Technology

1991-09-30

the conduction mechanisms. Research supported by SD10/1IST & managed by Wright Laboratory 1. J.A. Herb , C. Bailey, K.V. Ravi, and P.A. Dennig, "The...1982 from [951 K. L Moazed, R. Nguyen, and J. R. Zeidler, "Ohmic contacts National Taiwan University, Taiwan , ROC. to semiconducting diamond," IEEE

European Solid State Device Research Conference (18th) Held on September 13-16 1988 in Montpellier, France. (ESSDERC 88)

DTIC Science & Technology

1988-09-16

IEEE Trans. Electron Dev., 30, pp 1295 (1983) /2/ K.K. Ng and W.T. Lynch, IEEE Trans. Electron Dev., 34, pp 503 (1987). /3/ P.A. van der Plas, W.C.E...300 20 F Ohm I FRC I 500 170 Ohm INPNICje F 65 F 28 fI Cjc F 100 j 45 I fF hFE I 80 j 80 II IBVEB I 6.5 F 6.5 V BVCE I 6.5 6.5 vI BVCB F 18 I 18 (V I...evaluated include a -Xb RAM, a 1.6GHz universal shift register and an 8 bit DAC with a 1.2ns settling time. A micograph of the DAC is shown in figure 6

Single-Word Multiple-Bit Upsets in Static Random Access Devices

DTIC Science & Technology

1998-01-15

Transactions on Nuclear Science, NS-33, 1616- 1619,1986. Criswell, T.L., P.R. Measel , and K.L. Walin, "Single Event Upset Testing with Relativistic...Heavy Ions," IEEE Transactions on Nuclear Science, NS-31, 1559- 1561,1984. 1946 3. Criswell, T.L., D.L. Oberg, J.L. Wert, P.R. Measel , and W.E

Organic electronic devices via interface engineering

NASA Astrophysics Data System (ADS)

Xu, Qianfei

This dissertation focuses on interface engineering and its influence on organic electronic devices. A comprehensive review of interface studies in organic electronic devices is presented in Chapter 1. By interface engineering at the cathode contact, an ultra-high efficiency green polymer light emitting diode is demonstrated in Chapter 2. The interface modification turns out to be solution processable by using calcium acetylacetonate, donated by Ca(acac)2. The device structure is Induim Tin Oxide (ITO)/3,4-polyethylenedioxythiophene-polystyrene-sulfonate (PEDOT)/Green polyfluorene/Ca(acac) 2/Al. Based on this structure, we obtained device efficiencies as high as 28 cd/A at 2650 cd/m2, which is about a 3 times improvement over previous devices. The mechanism of this nano-layer has been studied by I-L-V measurements, photovoltaic measurements, XPS/UPS studies, impedance measurements as well as transient EL studies. The interfacial layer plays a crucial role for the efficiency improvement. It is believed to work as a hole blocking layer as well as an electron injection layer. Meanwhile, a systematic study on ITO electrodes is also carried out in Chapter 4. By engineering the interface at ITO electrode, the device lifetime has been improved. In Chapter 5, very bright white emission PLEDs are fabricated based on blue polyfluorene (PF) doped with 1 wt% 6, 8, 15, 17-tetraphyenyl-1.18, 4.5, 9.10, 13.14-tetrabenzoheptacene (TBH). The maximum luminance exceeds 20,000 cd/m2. The maximum luminance efficiency is 3.55 cd/A at 4228 cd/m2 while the maximum power efficiency is 1.6 lm/W at 310 cd/m2. The white color is achieved by an incomplete energy transfer from blue PF to TBH. The devices show super stable CIE coordinates as a function of current density. The interface engineering is also applied to memory devices. In Chapter 6, a novel nonvolatile memory device is fabricated by inserting a buffer layer at the anode contact. Devices with the structure of Cu/Buffer-layer/organic layer/Cu show very attractive electrical bi-stability. The switching mechanism is believed to origin from by the different copper ion concentrations in the organic layer. This opens up a promising way to achieve high-performance organic electronic devices.

1988 IEEE Annual Conference on Nuclear and Space Radiation Effects, 25th, Portland, OR, July 12-15, 1988, Proceedings

NASA Technical Reports Server (NTRS)

Coakley, Peter G. (Editor)

1988-01-01

The effects of nuclear and space radiation on the performance of electronic devices are discussed in reviews and reports of recent investigations. Topics addressed include the basic mechanisms of radiation effects, dosimetry and energy-dependent effects, sensors in and for radiation environments, EMP/SGEMP/IEMP phenomena, radiation effects on isolation technologies, and spacecraft charging and space radiation effects. Consideration is given to device radiation effects and hardening, hardness assurance and testing techniques, IC radiation effects and hardening, and single-event phenomena.

Signal Processing Using Surface Acoustic Wave Devices and Its Application to Spread Spectrum Communication Systems.

DTIC Science & Technology

1979-12-13

I III| I IIG since t - T < T = t - L (W - i) _ t is a point of stationary phase. -2a o 1 Eq. (4.86) shows that the output of the chirp filter is the...Parametric Interactions in Delay-Line Devices", IEEE Transactions on Microwave Theory and Techniques, vol. MTT-21, no. 4, April 1973, pp. 2414-257...443-476. Martin, T. A., "The IMCON Pulse Compression Filter and its Applications", IE3 Transactions on Microwave Theory and Techniques, vol. 21

Applications of one-dimensional structured nanomaterials as biosensors and transparent electronics

NASA Astrophysics Data System (ADS)

Ishikawa, Fumiaki

This dissertation presents applications of one-dimensional structured nanomaterials, carbon nanotubes and In2O3 nanowires, for biosensors and transparent electronics. Chapter 1 gives the motivation to study applications of one-dimensional structured nanomaterials, and also brief introduction to structure, synthesis, and electronic properties of carbon nanotubes and In2O3 nanowires. In Chapter 2, introduction and motivation of biosensors using nanotubes/nanowires is given, followed by an overview on important background knowledge and concepts in biosensing. In Chapter 3, application of carbon nanotube biosensors toward brown tide algae detection is presented. Our devices successfully detected a brown tide marker selectively with real-time response. In Chapter 4, we demonstrate that In2O3 nanowire biosensors coupled with an antibody mimic protein (Fibronectin, Fn) can be used to detect nucleocapsid (N) protein, a biomarker for severe acute respiratory syndrome (SARS), at concentrations to below the sub-nanomolar range. In Chapter 5, we develop an analytical method to calibrate nanowire biosensor responses that can suppress the device-to-device variation in sensing response significantly. In Chapter 6, we investigate the effect of nanotube density on the biosensor performance, and proved that it plays an important role through systematic studies. In Chapter 7, I propose a future direction of nanobiosensors research, and show preliminary results along the proposed direction. I first present a concept of an ideal bioassay system with a list of requirements for the system, and propose the strategy of multi-integration to establish a system based on nanobiosensors that satisfies all of the requirements. In Chapter 8, we demonstrate high performance fully transparent transistors based on transfer printed aligned carbon nanotubes on both rigid and flexible substrates. We achieved device mobility as high as 1,300 cm 2V-1s-1 on glass substrates, which is the highest among transparent transistors reported so far. We also demonstrated fully transparent PMOS inverters on flexible substrates, and also successfully controlled commercial GaN light--emitting diodes (LEDs) with light intensity modulation of 103. Lastly, a brief summary of this thesis is given in Chapter 9.

Path loss variation of on-body UWB channel in the frequency bands of IEEE 802.15.6 standard.

PubMed

Goswami, Dayananda; Sarma, Kanak C; Mahanta, Anil

2016-06-01

The wireless body area network (WBAN) has gaining tremendous attention among researchers and academicians for its envisioned applications in healthcare service. Ultra wideband (UWB) radio technology is considered as excellent air interface for communication among body area network devices. Characterisation and modelling of channel parameters are utmost prerequisite for the development of reliable communication system. The path loss of on-body UWB channel for each frequency band defined in IEEE 802.15.6 standard is experimentally determined. The parameters of path loss model are statistically determined by analysing measurement data. Both the line-of-sight and non-line-of-sight channel conditions are considered in the measurement. Variations of parameter values with the size of human body are analysed along with the variation of parameter values with the surrounding environments. It is observed that the parameters of the path loss model vary with the frequency band as well as with the body size and surrounding environment. The derived parameter values are specific to the particular frequency bands of IEEE 802.15.6 standard, which will be useful for the development of efficient UWB WBAN system.

Inexpensive semi-autonomous ground vehicles for defusing IEDs

NASA Astrophysics Data System (ADS)

Davenport, Chris; Lodmell, James; Womble, Phillip C.; Barzilov, Alexander; Paschal, Jon; Hernandez, Robert; Moss, Kyle T.; Hopper, Lindsay

2008-04-01

Improvised explosive devices (IEDs) are an important concern to coalition forces during the conflicts in the Middle East. These devices are responsible for many casualties to American armed forces in the Middle East. These explosives are particularly dangerous because they are improvised with materials readily available to the designer, and there is no systematic way of explosive ordinance disposal. IEDs can be made from things such as standard military ammunition and can be detonated with common electronic devices such as cell phones and garage door openers. There is a great need for a low cost solution to neutralize these IEDs. At the Applied Physics Institute we are building a single function disrupter robot whose sole purpose is to neutralize these IEDs. We are modifying a toy remote control car to control it either wirelessly using WI-FI (IEEE 802.11) or wired by tethering the vehicle with an Ethernet cable (IEEE 802.3). The robot will be equipped with a high velocity fuze disrupter to neutralize the IED as well as a video camera for inspection and aiming purposes. This robot utilizes commercial-off-the-shelf (COTS) components which keeps the cost relatively low. Currently, similar robot systems have been deployed in Iraq and elsewhere but their method of operation is such that it is impractical to use in non-combat situations. We will discuss our design and possible deployment scenarios.

Novel chemistries and materials for grid-scale energy storage: Quinones and halogen catalysis

NASA Astrophysics Data System (ADS)

Huskinson, Brian Thomas

In this work I describe various approaches to electrochemical energy storage at the grid-scale. Chapter 1 provides an introduction to energy storage and an overview of the history and development of flow batteries. Chapter 2 describes work on the hydrogen-chlorine regenerative fuel cell, detailing its development and the record-breaking performance of the device. Chapter 3 dives into catalyst materials for such a fuel cell, focusing on ruthenium oxide based alloys to be used as chlorine redox catalysts. Chapter 4 introduces and details the development of a performance model for a hydrogen-bromine cell. Chapter 5 delves into the more recent work I have done, switching to applications of quinone chemistries in flow batteries. It focuses on the pairing of one particular quinone (2,7-anthraquinone disulfonic acid) with bromine, and highlights the promising performance characteristics of a device based on this type of chemistry.

Real-time modeling and simulation of distribution feeder and distributed resources

NASA Astrophysics Data System (ADS)

Singh, Pawan

The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.

Micro- and nano-scale optical devices for high density photonic integrated circuits at near-infrared wavelengths

NASA Astrophysics Data System (ADS)

Chatterjee, Rohit

In this research work, we explore fundamental silicon-based active and passive photonic devices that can be integrated together to form functional photonic integrated circuits. The devices which include power splitters, switches and lenses are studied starting from their physics, their design and fabrication techniques and finally from an experimental standpoint. The experimental results reveal high performance devices that are compatible with standard CMOS fabrication processes and can be easily integrated with other devices for near infrared telecom applications. In Chapter 2, a novel method for optical switching using nanomechanical proximity perturbation technique is described and demonstrated. The method which is experimentally demonstrated employs relatively low powers, small chip footprint and is compatible with standard CMOS fabrication processes. Further, in Chapter 3, this method is applied to develop a hitless bypass switch aimed at solving an important issue in current wavelength division multiplexing systems namely hitless switching of reconfigurable optical add drop multiplexers. Experimental results are presented to demonstrate the application of the nanomechanical proximity perturbation technique to practical situations. In Chapter 4, a fundamental photonic component namely the power splitter is described. Power splitters are important components for any photonic integrated circuits because they help split the power from a single light source to multiple devices on the same chip so that different operations can be performed simultaneously. The power splitters demonstrated in this chapter are based on multimode interference principles resulting in highly compact low loss and highly uniform power splitting to split the power of the light from a single channel to two and four channels. These devices can further be scaled to achieve higher order splitting such as 1x16 and 1x32 power splits. Finally in Chapter 5 we overcome challenges in device fabrication and measurement techniques to demonstrate for the first time a "superlens" for the technologically important near infrared wavelength ranges with the opportunity to scale down further to visible wavelengths. The observed resolution is 0.47lambda, clearly smaller than the diffraction limit of 0.61lambda and is supported by detailed theoretical analyses and comprehensive numerical simulations. Importantly, we clearly show for the first time this subdiffraction limit imaging is due to the resonant excitation of surface slab modes, permitting amplification of evanescent waves. The demonstrated "superlens" has the largest figure of merit ever reported till date both theoretically and experimentally. The techniques and devices described in this thesis can be further applied to develop new devices with different functionalities. In Chapter 6 we describe two examples using these ideas. First, we experimentally demonstrate the use of the nanomechanical proximity perturbation technique to develop a phase retarder for on-chip all state polarization control. Next, we use the negative refraction photonic crystals described in Chapter 5 to achieve a special kind of bandgap called the zero-n¯ bandgap having unique properties.

Hybrid III-V Silicon Lasers

NASA Astrophysics Data System (ADS)

Bowers, John

2014-03-01

Abstract: A number of important breakthroughs in the past decade have focused attention on Si as a photonic platform. We review here recent progress in this field, focusing on efforts to make lasers, amplifiers, modulators and photodetectors on or in silicon. We also describe optimum quantum well design and distributed feedback cavity design to reduce the threshold and increase the efficiency and power output. The impact active silicon photonic integrated circuits could have on interconnects, telecommunications and on silicon electronics is reviewed. Biography: John Bowers holds the Fred Kavli Chair in Nanotechnology, and is the Director of the Institute for Energy Efficiency and a Professor in the Departments of Electrical and Computer Engineering and Materials at UCSB. He is a cofounder of Aurrion, Aerius Photonics and Calient Networks. Dr. Bowers received his M.S. and Ph.D. degrees from Stanford University and worked for AT&T Bell Laboratories and Honeywell before joining UC Santa Barbara. Dr. Bowers is a member of the National Academy of Engineering and a fellow of the IEEE, OSA and the American Physical Society. He is a recipient of the OSA/IEEE Tyndall Award, the OSA Holonyak Prize, the IEEE LEOS William Streifer Award and the South Coast Business and Technology Entrepreneur of the Year Award. He and coworkers received the EE Times Annual Creativity in Electronics (ACE) Award for Most Promising Technology for the hybrid silicon laser in 2007. Bowers' research is primarily in optoelectronics and photonic integrated circuits. He has published ten book chapters, 600 journal papers, 900 conference papers and has received 54 patents. He has published 180 invited papers and conference papers, and given 16 plenary talks at conferences. As well as Chong Zhang.

A 32 kb 9T near-threshold SRAM with enhanced read ability at ultra-low voltage operation

NASA Astrophysics Data System (ADS)

Kim, Tony Tae-Hyoung; Lee, Zhao Chuan; Do, Anh Tuan

2018-01-01

Ultra-low voltage SRAMs are highly sought-after in energy-limited systems such as battery-powered and self-harvested SoCs. However, ultra-low voltage operation diminishes SRAM read bitline (RBL) sensing margin significantly. This paper tackles this issue by presenting a novel 9T cell with data-independent RBL leakage in combination with an RBL boosting technique for enhancing the sensing margin. The proposed technique automatically tracks process, temperature and voltage (PVT) variations for robust sensing margin enhancement. A test chip fabricated in 65 nm CMOS technology shows that the proposed scheme significantly enlarges the sensing margin compared to the conventional bitline sensing scheme. It also achieves the minimum operating voltage of 0.18 V and the minimum energy consumption of 0.92 J/access at 0.4 V. He received 2016 International Low Power Design Contest Award from ISLPED, a best paper award at 2014 and 2011 ISOCC, 2008 AMD/CICC Student Scholarship Award, 2008 Departmental Research Fellowship from Univ. of Minnesota, 2008 DAC/ISSCC Student Design Contest Award, 2008, 2001, and 1999 Samsung Humantec Thesis Award and, 2005 ETRI Journal Paper of the Year Award. He is an author/co-author of +100 journal and conference papers and has 17 US and Korean patents registered. His current research interests include low power and high performance digital, mixed- mode, and memory circuit design, ultra-low voltage circuits and systems design, variation and aging tolerant circuits and systems, and circuit techniques for 3D ICs. He serves as an associate editor of IEEE Transactions on VLSI Systems. He is an IEEE senior member and the Chair of IEEE Solid-State Circuits Society Singapore Chapter. He has served numerous conferences as a committee member.

1997 IEEE/LEOS Summer Topical Meeting on Gallium Nitride Materials, Processing and Devices Held in Montreal, Quebec, Canada on 11-15 August 1997

DTIC Science & Technology

1998-01-01

photochemical exposure, these monomer systems form highly crosslinked networks which exhibit low intrinsic ab- sorption in the wavelength range extending...losses. The tip is also coated with a PFA Teflon coating to minimize the sticking of the cauterized tissue onto the tip. The dedicated forceps is mounted

1990 IEEE Annual Conference on Nuclear and Space Radiation Effects, 27th, Reno, NV, July 16-20, 1990, Proceedings

NASA Technical Reports Server (NTRS)

Fleetwood, Daniel M. (Editor)

1990-01-01

Various papers on nuclear and space radiation effects are presented. The general topics addressed include: basic mechanisms of radiation effects, dosimetry and energy-dependent effects, hardness assurance and testing techniques, single-event upset and latchup, isolation technologies, device and integrated circuit effects and hardening, spacecraft charging and electromagnetic effects.

78 FR 37499 - Unlicensed National Information Infrastructure (U-NII) Devices in the 5 GHz Band

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-21

... comments by the current deadline. On June 6, 2013, the Wi-Fi Alliance also requested a 30 day extension of... proceeding. The Wi-Fi Alliance points out that the current reply comment filing deadline falls before both the 2013 Wi-Fi Alliance Member Meeting and IEEE 802's Plenary Session, and that the parties' reply...

Optoelectronic Devices, Sensors, Communication and Multimedia, Photonics Applications and Web Engineering, Wilga, May 2012

NASA Astrophysics Data System (ADS)

Romaniuk, Ryszard S.

2012-05-01

This paper is the fourth part (out of five) of the research survey of WILGA Symposium work, May 2012 Edition, concerned with Optoelectronic Devices, Sensors, Communication and Multimedia (Video and Audio) technologies. It presents a digest of chosen technical work results shown by young researchers from different technical universities from this country during the Jubilee XXXth SPIE-IEEE Wilga 2012, May Edition, symposium on Photonics and Web Engineering. Topical tracks of the symposium embraced, among others, nanomaterials and nanotechnologies for photonics, sensory and nonlinear optical fibers, object oriented design of hardware, photonic metrology, optoelectronics and photonics applications, photonics-electronics co-design, optoelectronic and electronic systems for astronomy and high energy physics experiments, JET tokamak and pi-of-the sky experiments development. The symposium is an annual summary in the development of numerable Ph.D. theses carried out in this country in the area of advanced electronic and photonic systems. It is also a great occasion for SPIE, IEEE, OSA and PSP students to meet together in a large group spanning the whole country with guests from this part of Europe. A digest of Wilga references is presented [1-270].

Electromagnetic Interference Assessment of CDMA and GSM Wireless Phones to Aircraft Navigation Radios

NASA Technical Reports Server (NTRS)

Ely, Jay J.; Nguyen, Truong X.; Koppen, Sandra V.; Salud, M. Theresa

2002-01-01

To address the concern for cellular phone electromagnetic interference (EMI) to aircraft radios, a radiated emission measurement process for CDMA (IS-95) and GSM (ETSI GSM 11.22) wireless handsets was developed. Spurious radiated emissions were efficiently characterized from devices tested in either a semi-anechoic or reverberation chamber, in terms of effective isotropic radiated power. Eight representative handsets (4 GSM, 4 CDMA) were commanded to operate while varying their radio transmitter parameters (power, modulation, etc.). This report provides a detailed description of the measurement process and resulting data, which may subsequently be used by others as a basis of consistent evaluation for cellular/PCS phones, Bluetooth, IEEE802.11b, IEEE802.11a, FRS/GMRS radios, and other portable transmitters. Aircraft interference path loss (IPL) and navigation radio interference threshold data from numerous reference documents, standards, and NASA partnerships were compiled. Using this data, a preliminary risk assessment is provided for CDMA and GSM wireless phone interference to aircraft localizer, Glideslope, VOR, and GPS radio receivers on typical transport airplanes. The report identifies where existing data for device emissions, IPL, and navigation radio interference thresholds needs to be extended for an accurate risk assessment for wireless transmitters in aircraft.

Spatial-Temporal Synchrophasor Data Characterization and Analytics in Smart Grid Fault Detection, Identification, and Impact Causal Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Huaiguang; Dai, Xiaoxiao; Gao, David Wenzhong

An approach of big data characterization for smart grids (SGs) and its applications in fault detection, identification, and causal impact analysis is proposed in this paper, which aims to provide substantial data volume reduction while keeping comprehensive information from synchrophasor measurements in spatial and temporal domains. Especially, based on secondary voltage control (SVC) and local SG observation algorithm, a two-layer dynamic optimal synchrophasor measurement devices selection algorithm (OSMDSA) is proposed to determine SVC zones, their corresponding pilot buses, and the optimal synchrophasor measurement devices. Combining the two-layer dynamic OSMDSA and matching pursuit decomposition, the synchrophasor data is completely characterized inmore » the spatial-temporal domain. To demonstrate the effectiveness of the proposed characterization approach, SG situational awareness is investigated based on hidden Markov model based fault detection and identification using the spatial-temporal characteristics generated from the reduced data. To identify the major impact buses, the weighted Granger causality for SGs is proposed to investigate the causal relationship of buses during system disturbance. The IEEE 39-bus system and IEEE 118-bus system are employed to validate and evaluate the proposed approach.« less

10 CFR 32.51 - Byproduct material contained in devices for use under § 31.5; requirements for license to...

Code of Federal Regulations, 2014 CFR

2014-01-01

... this chapter; and (iii) Under accident conditions (such as fire and explosion) associated with handling, storage and use of the device, it is unlikely that any person would receive an external radiation dose or..., “Caution-Radioactive Material,” the radiation symbol described in § 20.1901 of this chapter, and the name...

10 CFR 32.51 - Byproduct material contained in devices for use under § 31.5; requirements for license to...

Code of Federal Regulations, 2013 CFR

2013-01-01

... this chapter; and (iii) Under accident conditions (such as fire and explosion) associated with handling, storage and use of the device, it is unlikely that any person would receive an external radiation dose or..., “Caution-Radioactive Material,” the radiation symbol described in § 20.1901 of this chapter, and the name...

10 CFR 32.51 - Byproduct material contained in devices for use under § 31.5; requirements for license to...

Code of Federal Regulations, 2011 CFR

2011-01-01

... this chapter; and (iii) Under accident conditions (such as fire and explosion) associated with handling, storage and use of the device, it is unlikely that any person would receive an external radiation dose or..., “Caution-Radioactive Material,” the radiation symbol described in § 20.1901 of this chapter, and the name...

10 CFR 32.51 - Byproduct material contained in devices for use under § 31.5; requirements for license to...

Code of Federal Regulations, 2012 CFR

2012-01-01

... this chapter; and (iii) Under accident conditions (such as fire and explosion) associated with handling, storage and use of the device, it is unlikely that any person would receive an external radiation dose or..., “Caution-Radioactive Material,” the radiation symbol described in § 20.1901 of this chapter, and the name...

Portable Wireless Device Threat Assessment for Aircraft Navigation Radios

NASA Technical Reports Server (NTRS)

Nguyen, Truong X.; Koppen, Sandra V.; Ely, Jay J.; Williams, Reuben A.; Smith, Laura J.; Salud, Maria Theresa P.

2004-01-01

This paper addresses the concern for Wireless Local Area Network devices and two-way radios to cause electromagnetic interference to aircraft navigation radio systems. Spurious radiated emissions from various IEEE 802.11a, 802.11b, and Bluetooth devices are characterized using reverberation chambers. The results are compared with baseline emissions from standard laptop computer and personal digital assistants (PDAs) that are currently allowed for use on aircraft. The results indicate that the WLAN devices tested are not more of a threat to aircraft navigation radios than standard laptop computers and PDAs in most aircraft bands. In addition, spurious radiated emission data from seven pairs of two-way radios are provided. These two-way radios emit at much higher levels in the bands considered. A description of the measurement process, device modes of operation and the measurement results are reported.

Development of closed-fitting-type walking assistance device for legs and evaluation of muscle activity.

PubMed

Ikehara, Tadaaki; Nagamura, Kazuteru; Ushida, Takurou; Tanaka, Eiichirou; Saegusa, Shozo; Kojima, Sho; Yuge, Louis

2011-01-01

A walking assistance device using a flexible shaft was developed. The combination of a flexible shaft with a worm gear was successfully adopted on this device to simplify its appearance and reduce its size. A hybrid - control system on this device controls both torque and angle at the ankle and knee joints. In this system, the torsional spring constant of the flexible shaft is taken into account by the motor in controlling the power and angle of rotation of the motor. To expand the area in which a person may use the device, it is equipped with a self-contained system powered by a Lithium-ion battery and controlled by an SH-4 microcomputer and actuators, consisting of motors and gears, all of which are carried in a small backpack. Consequently, persons using the device may walk freely in both indoor and outdoor environments. © 2011 IEEE

A System Implementation for Cooperation between UHF RFID Reader and TCP/IP Device

NASA Astrophysics Data System (ADS)

Lee, Sang Hoon; Jin, Ik Soo

This paper presents a system implementation for cooperation between UHF RFID reader and TCP/IP device that can be used as a home gateway. The system consists of an UHF RFID tag, an UHF RFID reader, a RF end-device, a RF coordinator and a TCP/IP I/F. The UHF RFID reader is compatible with EPC Class-0/Gen1, Class-1/Gen1, 2 and ISO18000-6B, operating at the 915MHz. In particular, UHF RFID reader can be combined with a RF end device/coordinator for ZigBee(IEEE 802.15.4) interface which is low power wireless standard. The TCP/IP device is communicated with RFID reader via wired type. On the other hand, it is connected with ZigBee end-device via wireless type. The experimental results show that the developed system can provide the right networking.

IEEE Smart Grid Series of Standards IEEE 2030 (Interoperability) and IEEE 1547 (Interconnection) Status: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Basso, T.; DeBlasio, R.

The IEEE American National Standards smart grid publications and standards development projects IEEE 2030, which addresses smart grid interoperability, and IEEE 1547TM, which addresses distributed resources interconnection with the grid, have made substantial progress since 2009. The IEEE 2030TM and 1547 standards series focus on systems-level aspects and cover many of the technical integration issues involved in a mature smart grid. The status and highlights of these two IEEE series of standards, which are sponsored by IEEE Standards Coordinating Committee 21 (SCC21), are provided in this paper.

Pesticide Devices: A Guide for Consumers

EPA Pesticide Factsheets

This guide for consumers explains key facts about pesticide devices and how they differ from registered pesticide products. Device producers or registrants should see our Pesticide Registration Manual, Chapter 13 for information.

The Influence of Polymer Sequence on the Formation of Bulk-Heterojunctions in Organic Solar Cells

NASA Astrophysics Data System (ADS)

Gao, Dong

This thesis summarizes my work on organic solar cells during my graduate studies. Chapter 1 serves as an introduction to organic solar cells. I will briefly discuss the working mechanism, and describe the device fabrication processes and testing set up that I designed at the beginning of my graduate studies. Chapter 2 describes the size-dependent behavior of polymer solar cells measured under partial illumination. We found that ITO resistance is a significant source of power loss because sheet resistance (Rs) increases with area. The non-illuminated part of a partially illuminated device introduces some interesting effects related to the physics of device operation. Specifically, this contributes additional "dark diodes" that connect in parallel with an illuminated cell, giving rise to an apparent decrease in VOC and increase in FF as the illuminated portion of the cell is decreased. Chapter 3 is a study of a P3HS-b-P3HT block copolymer as a donor material in organic solar cells. Fiber-like nanostructures are formed spontaneously in P3HS-b-P3HT:PCBM devices, and their thermal stability exceeds homopolymer:PCBM devices or ternary mixtures. Although P3HS-b-P3HT contains two distinct electron donor materials, the EQE spectra, hole mobility, Jsc, and PCE exceed that of a physical mixture of the two homopolymers and PCBM. Chapter 4 compares the photovoltaic properties of two conjugated copolymers with the same composition, P3HS-b-P3HT and P3HS- s-P3HT. The block polymer spontaneously undergoes intrinsic phase separation and the statistical polymer does not. P3HS-b-P3HT devices perform best when the native self-assembled structure is most perturbed, which is accomplished using PC71BM. P3HS-s-P3HT is a polymer that does not form a native phase separated structure. Here vapor annealing can be used to more predictably optimize the polymer:fullerene morphology. Chapter 5 studies the evolution of the electron mobility of two different acceptors with different crystallinity, PC71BM and ICBA, in a crystallized P3HT matrix during a prolonged thermal aging process. ICBA has an electron mobility that is over an order of magnitude lower than PC71BM. Given that both devices use the same polymer donor, it appears that high electron mobility does not correlate with the best device performance. The evolution of the acceptor appears to be the dominant factor that leads to long term changes in devices. Chapter 6 describes the synthesis of donor-acceptor copolymers with a "blocky" structure. Selenophene is introduced into PBDTTT-C-T in order to improve molecular ordering between polymer chains. Though more ordered morphologies are observed with blocky polymers, the physical mixture of parent polymers perform better in solar cell devices, which is not well correlated with morphology. Chapter 7 summarizes the above work and discusses the further directions in organic solar cell research.

Load-Speed Interaction Effects on the Biomechanics of Backpack Load Carriage

DTIC Science & Technology

2001-05-01

Duchenn muscular dystrophy . Developmental Med and Child Neurology, 23:3- 22, 1981. 39. Winter, D.A. Biomechanics of Human Movement. John Wiley & Sons, Inc...and C.J. De Luca. Muscle fatigue monitor: A noninvasive device for observing localized muscular fatigue. IEEE Transactions on Biomedical Engineering...joint forces, muscle torques, muscle electrical activity and backpack acceleration increased when speed andlor load increased, likely increasing the

Electrostatic Discharge Training Manual

DTIC Science & Technology

1980-09-01

CAN BE MOLDED INTO FORMED SHAPES. FIBERBOARD, MELAMINE LAMINATES AND OTHER MATERIALS (LAMINATED OR HOMOGENEOUS) CAN BE CONSTRUCTED INTO BOXES AND...COVERED WITH, ESD PROTECTIVE MATERIALS SUCH AS METAL, MIL-B-81705 TYPE II, MIL-P- 82646 (REFERENCES 17, 16), MELAMINE LAMINATES OR OTHER ESD PROTECTIVE...CONDUCTANCE IN AVALANCHE MICROWAVE OSCILLATORS", IEEE TRANSACTIONS ON ELECTRON DEVICES, ED-i5, JUNE 1968. 32. HOLM, R., ELECTRIC CONTACTS HANDBOOK, BERLIN

Scaling Properties of Gold Nanocluster Chemiresistor Sensors

DTIC Science & Technology

2006-05-01

Hooge 1408 IEEE SENSORS JOURNAL, VOL. 6, NO. 6, DECEMBER 2006 parameter [40]. Obviously, 1 / f noise ...Experimental Methods for Noise Research in Nanoscale Electronic Devices, vol. 151, Dordrecht, The Netherlands: Kluwer, 2004. [40] F . N. Hooge , “ 1 / f ...and because 1 / f noise tends to dominate, reduction in sensor size raises the noise floor, leading to a degradation in the detection limit. Because

Center of Excellence for Battlefield Capability Enhancements: Envronmentally Stable Flexible Displays

DTIC Science & Technology

2012-01-18

Lett. 60, 1453 1992. 3D. Look, Thin Solid Films 231, 61 1993. 4R. E. Pritchard, S. A. McQuaid, L. Hart, R. C. Newman , J. Mtikinen, H. J. von...Appl. Phys. 103, 123528 2008. 11F. W. Smith, A. R. Calawa, C. Chen, M. J. Manfra, and L. J. Mahoney , IEEE Electron Device Lett. 9, 77 1988. 12D. B

Implementation Of Secure 6LoWPAN Communications For Tactical Wireless Sensor Networks

DTIC Science & Technology

2016-09-01

wireless sensor networks (WSN) consist of power -constrained devices spread throughout a region-of-interest to provide data extraction in real time...1  A.  LOW POWER WIRELESS SENSOR NETWORKS ............................1  B.  INTRODUCTION TO...communication protocol for low power wireless personal area networks Since the IEEE 802.15.4 standard only defines the first two layers of the Open

Exploitation of RF-DNA for Device Classification and Verification Using GRLVQI Processing

DTIC Science & Technology

2012-12-01

5 FLD Fisher’s Linear Discriminant . . . . . . . . . . . . . . . . . . . 6 kNN K-Nearest Neighbor...Neighbor ( kNN ), Support Vector Machine (SVM), and simple cross-correlation techniques [40, 57, 82, 88, 94, 95]. The RF-DNA fingerprinting research in...Expansion and the Dis- crete Gabor Transform on a Non-Separable Lattice”. 2000 IEEE Int’l Conf on Acoustics, Speech , and Signal Processing (ICASSP00

Ultrasound-Based Guidance for Partial Breast Irradiation Therapy

DTIC Science & Technology

2012-01-01

displace- 0278-0062/$20.00 © IEEE Authorized licensed use limited to: IEEE Xplore . Downloaded on January 5, 2009 at 17:37 from IEEE Xplore . Restrictions...Authorized licensed use limited to: IEEE Xplore . Downloaded on January 5, 2009 at 17:37 from IEEE Xplore . Restrictions apply. RIVAZ et al...better CNR values: the Authorized licensed use limited to: IEEE Xplore . Downloaded on January 5, 2009 at 17:37 from IEEE Xplore . Restrictions apply

Radiated EMC immunity investigation of common recognition identification platform for medical applications

NASA Astrophysics Data System (ADS)

Miranda, Jorge; Cabral, Jorge; Ravelo, Blaise; Wagner, Stefan; Pedersen, Christian F.; Memon, Mukhtiar; Mathiesen, Morten

2015-01-01

An innovative e-healthcare platform named common recognition and identification platform (CRIP) was developed and tested as part of the CareStore project. CareStore and CRIP aims at delivering accurate and safe disease management by minimising human operator errors in hospitals and care facilities. To support this, the CRIP platform features fingerprint biometrics and near field communication (NFC) for user identification; and Bluetooth communication support for a range of telemedicine medical devices adhering to the IEEE 11073 standard. The aim of this study was to evaluate the electromagnetic compatibility (EMC) immunity of the CRIP platform in order to validate it for medical application use. The first prototype of CRIP was demonstrated to operate as expected by showing the user identification function feasibility, both via NFC and biometric, and by detection of Bluetooth devices via radio frequency (RF) scanning. The NFC module works in the 13.56 MHz band and the Bluetooth module work in the 2.4 GHz band, according to the IEEE 802.15.1 standard. The standard test qualification of the CRIP was performed based on the radiated EMC immunity with respect to the EN 61000-4-3 standard. The immunity tests were conducted under industrial EMC compliance with electric field aggression, with levels up to 10 V/m in both horizontal and vertical polarisations when the test antenna and the CRIP were placed at a distance of 3 m. It was found that the CRIP device complies with the European electromagnetic (EM) radiation immunity requirements.

Telemonitoring systems interoperability challenge: an updated review of the applicability of ISO/IEEE 11073 standards for interoperability in telemonitoring.

PubMed

Galarraga, M; Serrano, L; Martinez, I; de Toledo, P; Reynolds, Melvin

2007-01-01

Advances in Information and Communication Technologies, ICT, are bringing new opportunities and use cases in the field of systems and Personal Health Devices used for the telemonitoring of citizens in Home or Mobile scenarios. At a time of such challenges, this review arises from the need to identify robust technical telemonitoring solutions that are both open and interoperable. These systems demand standardized solutions to be cost effective and to take advantage of standardized operation and interoperability. Thus, the fundamental challenge is to design plug-&-play devices that, either as individual elements or as components, can be incorporated in a simple way into different Telecare systems, perhaps configuring a personal user network. Moreover, there is an increasing market pressure from companies not traditionally involved in medical markets, asking for a standard for Personal Health Devices, which foresee a vast demand for telemonitoring, wellness, Ambient Assisted Living (AAL) and e-health applications. However, the newly emerging situations imply very strict requirements for the protocols involved in the communication. The ISO/IEEE 11073 family of standards is adapting and moving in order to face the challenge and might appear the best positioned international standards to reach this goal. This work presents an updated survey of these standards, trying to track the changes that are being fulfilled, and tries to serve as a starting-point for those who want to familiarize themselves with them.

IEEE 802.21 Assisted Seamless and Energy Efficient Handovers in Mixed Networks

NASA Astrophysics Data System (ADS)

Liu, Huaiyu; Maciocco, Christian; Kesavan, Vijay; Low, Andy L. Y.

Network selection is the decision process for a mobile terminal to handoff between homogeneous or heterogeneous networks. With multiple available networks, the selection process must evaluate factors like network services/conditions, monetary cost, system conditions, user preferences etc. In this paper, we investigate network selection using a cost function and information provided by IEEE 802.21. The cost function provides flexibility to balance different factors in decision making and our research is focused on improving both seamlessness and energy efficiency of handovers. Our solution is evaluated using real WiFi, WiMax, and 3G signal strength traces. The results show that appropriate networks were selected based on selection policies, handovers were triggered at optimal times to increase overall network connectivity as compared to traditional triggering schemes, while at the same time the energy consumption of multi-radio devices for both on-going operations as well as during handovers is optimized.

Field-programmable gate array implementation of an all-digital IEEE 802.15.4-compliant transceiver

NASA Astrophysics Data System (ADS)

Cornetta, Gianluca; Touhafi, Abdellah; Santos, David J.; Vázquez, José M.

2010-12-01

An architecture for a low-cost, low-complexity digital transceiver is presented in this article. The proposed architecture targets the IEEE 802.15.4 standard for short-range wireless personal area networks and has been implemented as a synthesisable VHDL register transfer level description. The system has been evaluated and tested using a Xilinx 90 nm Virtex-4 field-programmable gate array as the target technology. Bit error rate (BER) and error vector magnitude (EVM) have been used as the figures of merit for modem performance. Simulations show that the recommended minimum BER is achieved at E b/N 0 = 8.7 dB, whereas the EVM is 19.5%. The implemented device occupies 10% of the target FPGA and has a normalised maximum power consumption of 44 mW in transmit mode and 53 mW in receiver mode.

Performance analysis and improvement of WPAN MAC for home networks.

PubMed

Mehta, Saurabh; Kwak, Kyung Sup

2010-01-01

The wireless personal area network (WPAN) is an emerging wireless technology for future short range indoor and outdoor communication applications. The IEEE 802.15.3 medium access control (MAC) is proposed to coordinate the access to the wireless medium among the competing devices, especially for short range and high data rate applications in home networks. In this paper we use analytical modeling to study the performance analysis of WPAN (IEEE 802.15.3) MAC in terms of throughput, efficient bandwidth utilization, and delay with various ACK policies under error channel condition. This allows us to introduce a K-Dly-ACK-AGG policy, payload size adjustment mechanism, and Improved Backoff algorithm to improve the performance of the WPAN MAC. Performance evaluation results demonstrate the impact of our improvements on network capacity. Moreover, these results can be very useful to WPAN application designers and protocol architects to easily and correctly implement WPAN for home networking.

Development of a low mobility IEEE 802.15.4 compliant VANET system for urban environments.

PubMed

Nazabal, Juan Antonio; Falcone, Francisco; Fernández-Valdivielso, Carlos; Matías, Ignacio Raúl

2013-05-29

The use of Vehicular Ad-Hoc Networks (VANETs) is growing nowadays and it includes both roadside-to-vehicle communication (RVC) and inter-vehicle communication (IVC). The purpose of VANETs is to exchange useful information between vehicles and the roadside infrastructures for making an intelligent use of them. There are several possible applications for this technology like: emergency warning system for vehicles, cooperative adaptive cruise control or collision avoidance, among others. The objective of this work is to develop a VANET prototype system for urban environments using IEEE 802.15.4 compliant devices. Simulation-based values of the estimated signal strength and radio link quality values are obtained and compared with measurements in outdoor conditions to validate an implemented VANET system. The results confirm the possibility of implementing low cost vehicular communication networks operating at moderate vehicular speeds.

Performance Analysis and Improvement of WPAN MAC for Home Networks

PubMed Central

Mehta, Saurabh; Kwak, Kyung Sup

2010-01-01

The wireless personal area network (WPAN) is an emerging wireless technology for future short range indoor and outdoor communication applications. The IEEE 802.15.3 medium access control (MAC) is proposed to coordinate the access to the wireless medium among the competing devices, especially for short range and high data rate applications in home networks. In this paper we use analytical modeling to study the performance analysis of WPAN (IEEE 802.15.3) MAC in terms of throughput, efficient bandwidth utilization, and delay with various ACK policies under error channel condition. This allows us to introduce a K-Dly-ACK-AGG policy, payload size adjustment mechanism, and Improved Backoff algorithm to improve the performance of the WPAN MAC. Performance evaluation results demonstrate the impact of our improvements on network capacity. Moreover, these results can be very useful to WPAN application designers and protocol architects to easily and correctly implement WPAN for home networking. PMID:22319274

Assistive technology for ultrasound-guided central venous catheter placement.

PubMed

Ikhsan, Mohammad; Tan, Kok Kiong; Putra, Andi Sudjana

2018-01-01

This study evaluated the existing technology used to improve the safety and ease of ultrasound-guided central venous catheterization. Electronic database searches were conducted in Scopus, IEEE, Google Patents, and relevant conference databases (SPIE, MICCAI, and IEEE conferences) for related articles on assistive technology for ultrasound-guided central venous catheterization. A total of 89 articles were examined and pointed to several fields that are currently the focus of improvements to ultrasound-guided procedures. These include improving needle visualization, needle guides and localization technology, image processing algorithms to enhance and segment important features within the ultrasound image, robotic assistance using probe-mounted manipulators, and improving procedure ergonomics through in situ projections of important information. Probe-mounted robotic manipulators provide a promising avenue for assistive technology developed for freehand ultrasound-guided percutaneous procedures. However, there is currently a lack of clinical trials to validate the effectiveness of these devices.

28 CFR 3.5 - Forfeiture of gambling devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Forfeiture of gambling devices. 3.5 Section 3.5 Judicial Administration DEPARTMENT OF JUSTICE GAMBLING DEVICES § 3.5 Forfeiture of gambling devices. For purposes of seizure and forfeiture of gambling devices see section 8 of this chapter. [Order...

28 CFR 3.5 - Forfeiture of gambling devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 28 Judicial Administration 1 2011-07-01 2011-07-01 false Forfeiture of gambling devices. 3.5 Section 3.5 Judicial Administration DEPARTMENT OF JUSTICE GAMBLING DEVICES § 3.5 Forfeiture of gambling devices. For purposes of seizure and forfeiture of gambling devices see section 8 of this chapter. [Order...

28 CFR 3.5 - Forfeiture of gambling devices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 1 2013-07-01 2013-07-01 false Forfeiture of gambling devices. 3.5 Section 3.5 Judicial Administration DEPARTMENT OF JUSTICE GAMBLING DEVICES § 3.5 Forfeiture of gambling devices. For purposes of seizure and forfeiture of gambling devices see section 8 of this chapter. [Order...

28 CFR 3.5 - Forfeiture of gambling devices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 1 2012-07-01 2012-07-01 false Forfeiture of gambling devices. 3.5 Section 3.5 Judicial Administration DEPARTMENT OF JUSTICE GAMBLING DEVICES § 3.5 Forfeiture of gambling devices. For purposes of seizure and forfeiture of gambling devices see section 8 of this chapter. [Order...

28 CFR 3.5 - Forfeiture of gambling devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 1 2014-07-01 2014-07-01 false Forfeiture of gambling devices. 3.5 Section 3.5 Judicial Administration DEPARTMENT OF JUSTICE GAMBLING DEVICES § 3.5 Forfeiture of gambling devices. For purposes of seizure and forfeiture of gambling devices see section 8 of this chapter. [Order...

Design of a minimally constraining, passively supported gait training exoskeleton: ALEX II.

PubMed

Winfree, Kyle N; Stegall, Paul; Agrawal, Sunil K

2011-01-01

This paper discusses the design of a new, minimally constraining, passively supported gait training exoskeleton known as ALEX II. This device builds on the success and extends the features of the ALEX I device developed at the University of Delaware. Both ALEX (Active Leg EXoskeleton) devices have been designed to supply a controllable torque to a subject's hip and knee joint. The current control strategy makes use of an assist-as-needed algorithm. Following a brief review of previous work motivating this redesign, we discuss the key mechanical features of the new ALEX device. A short investigation was conducted to evaluate the effectiveness of the control strategy and impact of the exoskeleton on the gait of six healthy subjects. This paper concludes with a comparison between the subjects' gait both in and out of the exoskeleton. © 2011 IEEE

Optimal Operation and Dispatch of Voltage Regulation Devices Considering High Penetrations of Distributed Photovoltaic Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mather, Barry A; Hodge, Brian S; Cho, Gyu-Jung

Voltage regulation devices have been traditionally installed and utilized to support distribution voltages. Installations of distributed energy resources (DERs) in distribution systems are rapidly increasing, and many of these generation resources have variable and uncertain power output. These generators can significantly change the voltage profile for a feeder; therefore, in the distribution system planning stage of the optimal operation and dispatch of voltage regulation devices, possible high penetrations of DERs should be considered. In this paper, we model the IEEE 34-bus test feeder, including all essential equipment. An optimization method is adopted to determine the optimal siting and operation ofmore » the voltage regulation devices in the presence of distributed solar power generation. Finally, we verify the optimal configuration of the entire system through the optimization and simulation results.« less

Combining axial and radial nanowire heterostructures: radial Esaki diodes and tunnel field-effect transistors.

PubMed

Dey, Anil W; Svensson, Johannes; Ek, Martin; Lind, Erik; Thelander, Claes; Wernersson, Lars-Erik

2013-01-01

The ever-growing demand on high-performance electronics has generated transistors with very impressive figures of merit (Radosavljevic et al., IEEE Int. Devices Meeting 2009, 1-4 and Cho et al., IEEE Int. Devices Meeting 2011, 15.1.1-15.1.4). The continued scaling of the supply voltage of field-effect transistors, such as tunnel field-effect transistors (TFETs), requires the implementation of advanced transistor architectures including FinFETs and nanowire devices. Moreover, integration of novel materials with high electron mobilities, such as III-V semiconductors and graphene, are also being considered to further enhance the device properties (del Alamo, Nature 2011, 479, 317-323, and Liao et al., Nature 2010, 467, 305-308). In nanowire devices, boosting the drive current at a fixed supply voltage or maintaining a constant drive current at a reduced supply voltage may be achieved by increasing the cross-sectional area of a device, however at the cost of deteriorated electrostatics. A gate-all-around nanowire device architecture is the most favorable electrostatic configuration to suppress short channel effects; however, the arrangement of arrays of parallel vertical nanowires to address the drive current predicament will require additional chip area. The use of a core-shell nanowire with a radial heterojunction in a transistor architecture provides an attractive means to address the drive current issue without compromising neither chip area nor device electrostatics. In addition to design advantages of a radial transistor architecture, we in this work illustrate the benefit in terms of drive current per unit chip area and compare the experimental data for axial GaSb/InAs Esaki diodes and TFETs to their radial counterparts and normalize the electrical data to the largest cross-sectional area of the nanowire, i.e. the occupied chip area, assuming a vertical device geometry. Our data on lateral devices show that radial Esaki diodes deliver almost 7 times higher peak current, Jpeak = 2310 kA/cm(2), than the maximum peak current of axial GaSb/InAs(Sb) Esaki diodes per unit chip area. The radial TFETs also deliver high peak current densities Jpeak = 1210 kA/cm(2), while their axial counterparts at most carry Jpeak = 77 kA/cm(2), normalized to the largest cross-sectional area of the nanowire.

New Frontier Process using Bio Technology

DTIC Science & Technology

2013-02-05

p.58-59,2012. (2) H.Yamazaki, M.Fujii, Y.Ueoka, Y.ishikawa, M.Fujiwara, E.Takahashi, Y.Uraoka, “Highly Reliable a-InGaZnO Thin Film Transistors ...Electron Traps in SiO2/ IGZO Interface by Cyclic Capacitance–Voltage Method”, IEEE/ 2012 International Meeting for Future of Electron Devices, Kansai...Horita, Yasuaki Ishikawa, Yukiharu Uraoka, and Shinji Koh, “Characterizatio of Graphene Based Field Effect Transistors Using Nano Probing Microscopy

Theory and Device Modeling for Nano-Structured Transistor Channels

DTIC Science & Technology

2011-06-01

zinc oxide ( ZnO ) thin film transistors ( TFTs ) that contain nanocrystalline grains on the order of ~20nm. The authors of ref. 1 present results...problem in order to determine the threshold voltage. 15. SUBJECT TERMS nano-structured transistor , mesoscopic, zinc oxide , ZnO , field-effect...and R. Neidhard, “Microwave ZnO Thin - Film Transistors ”, IEEE Electron Dev. Lett. 29, 1024 (2008); doi: 10.1109/LED.2008.2001635.

1989 IEEE Annual Conference on Nuclear and Space Radiation Effects, 26th, Marco Island, FL, July 25-29, 1989, Proceedings. Part 1

NASA Technical Reports Server (NTRS)

Ochoa, Agustin, Jr. (Editor)

1989-01-01

Various papers on nuclear science are presented. The general topics addressed include: basic mechanics of radiation effects, dosimetry and energy-dependent effects, hardness assurance and testing techniques, spacecraft charging and space radiation effects, EMP/SGEMP/IEMP phenomena, device radiation effects and hardening, radiation effects on isolation technologies, IC radiation effects and hardening, and single-event phenomena.

Computer Modeling of Complete IC Fabrication Process.

DTIC Science & Technology

1984-01-01

Venson Shaw 10. C. S. Chang 11. Elizabeth Batson 12. Richard Pinto 13. Jacques Beauduoin SPEAKERS: 1. Tayo Akinwande 2. Dimitri Antoniadis 3. Walter...Numerical Model of Polysilicon Emitter Contacts in Bipolar Transistors,’ To be published IEEE Trans. Electron Devices. [34] M. R. Pinto , R. W. Dutton...Received PhD, Spring 1082) Balaji Swaminathan (Received PhD, Spring 1983) Len Mei Research Associate Michael Kump Research Assistant Mark Pinto Research

Heterogeneously Integrated Microwave Signal Generators with Narrow Linewidth Lasers

DTIC Science & Technology

2017-03-20

the linewidth in two ways: (1) increasing the photon lifetime due to effective cavity length enhancement, and (2) providing negative optical...structures. Some devices are also labeled. Figure 1. Microscope image of the photonic microwave generator comprising of two tunable lasers, a coupler...Integrated Photodiodes on Silicon,” IEEE JQE, vol.51, no.11, pp.1-6, Nov. 2015 Figure 9. (left) Optical spectra of two lasers comprising a photonic

Breaking open the set top box

NASA Astrophysics Data System (ADS)

Banks, David; Wiley, Anthony; Catania, Nicolas; Coles, Alastair N.; Smith, Duncan; Baynham, Simon; Deliot, Eric; Chidzey, Rod

1998-02-01

In this paper we describe the work being done at HP Labs Bristol in the area of home networks and gateways. This work is based on the idea of breaking open the set top box by physically separating the access network specific functions from the application specific functions. The access network specific functions reside in an access network gateway that can be shared by many end user devices. The first section of the paper present the philosophy behind this approach. The end user devices and the access network gateways must be interconnected by a high bandwidth network which can offer a bounded delay service for delay sensitive traffic. We are advocating the use of IEEE 1394 for this network, and the next section of the paper gives a brief introduction to this technology. We then describe a prototype digital video broadcasting satellite compliant gateway that we have built. This gateway could be used, for example, by a PC for receiving a data service or by a digital TV for receiving an MPEG-2 video service. A control architecture is the presented which uses a PC application to provide a web based user interface to the system. Finally, we provide details of our work on extending the reach of IEEE 1394 and its standardization status.

IEEE802.15.6 NB portable BAN clinic and M2M international standardization.

PubMed

Kuroda, Masahiro; Nohara, Yasunobu

2013-01-01

The increase of non communicable diseases (NCDs) will change the direction of health services to emphasize the role of preventive medicine in healthcare services. The first short-range medical body are network (BAN) standard IEEE802.15.6 is expected to be used for secure and user-friendly sensor devices for portable medical equipment. A BAN is an enabler for uploading medical data to a backend system for remote diagnoses and treatment. Machine-to-Machine (M2M) infrastructure is also a key technology for providing flexible and affordable services extending electronic health record (EHR) systems. This paper proposes a BAN-based portable clinic that collects health-check data from user-friendly medical devices and sensors and sends the data to a local backend server, and it evaluates the clinic in fields of actual usage. We discuss issues experienced from actual deployment of the system and focus on integrating it into upcoming healthcare M2M infrastructure to achieve affordable and dependable clinic services. We explain the components and workflow of the clinic and the system model. The system is set up at a temporary health center and has a network link to a remote medical help center. The paper concludes with our plan to introduce our system to contribute to internationally standardized preventive medicine.

47 CFR 15.305 - Equipment authorization requirement.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Section 15.305 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed Personal Communications Service Devices § 15.305 Equipment authorization requirement. PCS devices... 2 of this chapter before marketing. The application for certification must contain sufficient...

47 CFR 15.305 - Equipment authorization requirement.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Section 15.305 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES Unlicensed Personal Communications Service Devices § 15.305 Equipment authorization requirement. PCS devices... 2 of this chapter before marketing. The application for certification must contain sufficient...

An Improved Approach for RSSI-Based only Calibration-Free Real-Time Indoor Localization on IEEE 802.11 and 802.15.4 Wireless Networks.

PubMed

Passafiume, Marco; Maddio, Stefano; Cidronali, Alessandro

2017-03-29

Assuming a reliable and responsive spatial contextualization service is a must-have in IEEE 802.11 and 802.15.4 wireless networks, a suitable approach consists of the implementation of localization capabilities, as an additional application layer to the communication protocol stack. Considering the applicative scenario where satellite-based positioning applications are denied, such as indoor environments, and excluding data packet arrivals time measurements due to lack of time resolution, received signal strength indicator (RSSI) measurements, obtained according to IEEE 802.11 and 802.15.4 data access technologies, are the unique data sources suitable for indoor geo-referencing using COTS devices. In the existing literature, many RSSI based localization systems are introduced and experimentally validated, nevertheless they require periodic calibrations and significant information fusion from different sensors that dramatically decrease overall systems reliability and their effective availability. This motivates the work presented in this paper, which introduces an approach for an RSSI-based calibration-free and real-time indoor localization. While switched-beam array-based hardware (compliant with IEEE 802.15.4 router functionality) has already been presented by the author, the focus of this paper is the creation of an algorithmic layer for use with the pre-existing hardware capable to enable full localization and data contextualization over a standard 802.15.4 wireless sensor network using only RSSI information without the need of lengthy offline calibration phase. System validation reports the localization results in a typical indoor site, where the system has shown high accuracy, leading to a sub-metrical overall mean error and an almost 100% site coverage within 1 m localization error.

An Improved Approach for RSSI-Based only Calibration-Free Real-Time Indoor Localization on IEEE 802.11 and 802.15.4 Wireless Networks

PubMed Central

Passafiume, Marco; Maddio, Stefano; Cidronali, Alessandro

2017-01-01

Assuming a reliable and responsive spatial contextualization service is a must-have in IEEE 802.11 and 802.15.4 wireless networks, a suitable approach consists of the implementation of localization capabilities, as an additional application layer to the communication protocol stack. Considering the applicative scenario where satellite-based positioning applications are denied, such as indoor environments, and excluding data packet arrivals time measurements due to lack of time resolution, received signal strength indicator (RSSI) measurements, obtained according to IEEE 802.11 and 802.15.4 data access technologies, are the unique data sources suitable for indoor geo-referencing using COTS devices. In the existing literature, many RSSI based localization systems are introduced and experimentally validated, nevertheless they require periodic calibrations and significant information fusion from different sensors that dramatically decrease overall systems reliability and their effective availability. This motivates the work presented in this paper, which introduces an approach for an RSSI-based calibration-free and real-time indoor localization. While switched-beam array-based hardware (compliant with IEEE 802.15.4 router functionality) has already been presented by the author, the focus of this paper is the creation of an algorithmic layer for use with the pre-existing hardware capable to enable full localization and data contextualization over a standard 802.15.4 wireless sensor network using only RSSI information without the need of lengthy offline calibration phase. System validation reports the localization results in a typical indoor site, where the system has shown high accuracy, leading to a sub-metrical overall mean error and an almost 100% site coverage within 1 m localization error. PMID:28353676

Development of a Carbon Nanotube-Based Micro-CT and its Applications in Preclinical Research

NASA Astrophysics Data System (ADS)

Burk, Laurel May

Due to the dependence of researchers on mouse models for the study of human disease, diagnostic tools available in the clinic must be modified for use on these much smaller subjects. In addition to high spatial resolution, cardiac and lung imaging of mice presents extreme temporal challenges, and physiological gating methods must be developed in order to image these organs without motion blur. Commercially available micro-CT imaging devices are equipped with conventional thermionic x-ray sources and have a limited temporal response and are not ideal for in vivo small animal studies. Recent development of a field-emission x-ray source with carbon nanotube (CNT) cathode in our lab presented the opportunity to create a micro-CT device well-suited for in vivo lung and cardiac imaging of murine models for human disease. The goal of this thesis work was to present such a device, to develop and refine protocols which allow high resolution in vivo imaging of free-breathing mice, and to demonstrate the use of this new imaging tool for the study many different disease models. In Chapter 1, I provide background information about x-rays, CT imaging, and small animal micro-CT. In Chapter 2, CNT-based x-ray sources are explained, and details of a micro-focus x-ray tube specialized for micro-CT imaging are presented. In Chapter 3, the first and second generation CNT micro-CT devices are characterized, and successful respiratory- and cardiac-gated live animal imaging on normal, wild-type mice is achieved. In Chapter 4, respiratory-gated imaging of mouse disease models is demonstrated, limitations to the method are discussed, and a new contactless respiration sensor is presented which addresses many of these limitations. In Chapter 5, cardiac-gated imaging of disease models is demonstrated, including studies of aortic calcification, left ventricular hypertrophy, and myocardial infarction. In Chapter 6, several methods for image and system improvement are explored, and radiation therapy-related micro-CT imaging is present. Finally, in Chapter 7 I discuss future directions for this research and for the CNT micro-CT.

Robust Multi-Agent Sensor Network Systems

DTIC Science & Technology

2012-05-08

Localization on the Sphere, International Journal of Intelligent Defence Support System, Vol. 4, no. 4, 2011, pp. 328-350. Quality of Network... Quality of Service (QoS). The following standards are included in the IEEE 1609 standard family: IEEE P1609.0, IEEE P1609.1, IEEE P1609.2, IEEE P1609.3...protocols to support safety services in ITS,” in IEEE International Conference on Emerging Technologies and Factory Au- tomation (ETFA), 2008, pp. 1189

Analysis of elbow-joints misalignment in upper-limb exoskeleton.

PubMed

Malosio, Matteo; Pedrocchi, Nicola; Vicentini, Federico; Tosatti, Lorenzo Molinari

2011-01-01

This paper presents advantages of introducing elbow-joints misalignments in an exoskeleton for upper limb rehabilitation. Typical exoskeletons are characterized by axes of the device as much as possible aligned to the rotational axes of human articulations. This approach leads to advantages in terms of movements and torques decoupling, but can lead to limitations nearby the elbow singular configuration. A proper elbow axes misalignment between the exoskeleton and the human can improve the quality of collaborative rehabilitation therapies, in which a correct torque transmission from human articulations to mechanical joints of the device is required to react to torques generated by the patient. © 2011 IEEE

Improving the Energy Market: Algorithms, Market Implications, and Transmission Switching

NASA Astrophysics Data System (ADS)

Lipka, Paula Ann

This dissertation aims to improve ISO operations through a better real-time market solution algorithm that directly considers both real and reactive power, finds a feasible Alternating Current Optimal Power Flow solution, and allows for solving transmission switching problems in an AC setting. Most of the IEEE systems do not contain any thermal limits on lines, and the ones that do are often not binding. Chapter 3 modifies the thermal limits for the IEEE systems to create new, interesting test cases. Algorithms created to better solve the power flow problem often solve the IEEE cases without line limits. However, one of the factors that makes the power flow problem hard is thermal limits on the lines. The transmission networks in practice often have transmission lines that become congested, and it is unrealistic to ignore line limits. Modifying the IEEE test cases makes it possible for other researchers to be able to test their algorithms on a setup that is closer to the actual ISO setup. This thesis also examines how to convert limits given on apparent power---as is in the case in the Polish test systems---to limits on current. The main consideration in setting line limits is temperature, which linearly relates to current. Setting limits on real or apparent power is actually a proxy for using the limits on current. Therefore, Chapter 3 shows how to convert back to the best physical representation of line limits. A sequential linearization of the current-voltage formulation of the Alternating Current Optimal Power Flow (ACOPF) problem is used to find an AC-feasible generator dispatch. In this sequential linearization, there are parameters that are set to the previous optimal solution. Additionally, to improve accuracy of the Taylor series approximations that are used, the movement of the voltage is restricted. The movement of the voltage is allowed to be very large at the first iteration and is restricted further on each subsequent iteration, with the restriction corresponding to the accuracy and AC-feasiblity of the solution. This linearization was tested on the IEEE and Polish systems, which range from 14 to 3375 buses and 20 to 4161 transmission lines. It had an accuracy of 0.5% or less for all but the 30-bus system. It also solved in linear time with CPLEX, while the non-linear version solved in O(n1.11) to O(n1.39). The sequential linearization is slower than the nonlinear formulation for smaller problems, but faster for larger problems, and its linear computational time means it would continue solving faster for larger problems. A major consideration to implementing algorithms to solve the optimal generator dispatch is ensuring that the resulting prices from the algorithm will support the market. Since the sequential linearization is linear, it is convex, its marginal values are well-defined, and there is no duality gap. The prices and settlements obtained from the sequential linearization therefore can be used to run a market. This market will include extra prices and settlements for reactive power and voltage, compared to the present-day market, which is based on real power. An advantage of this is that there is a very clear pool that can be used for reactive power/voltage support payments, while presently there is not a clear pool to take them out of. This method also reveals how valuable reactive power and voltage are at different locations, which can enable better planning of reactive resource construction. Transmission switching increases the feasible region of the generator dispatch, which means there may be a better solution than without transmission switching. Power flows on transmission lines are not directly controllable; rather, the power flows according to how it is injected and the physical characteristics of the lines. Changing the network topology changes the physical characteristics, which changes the flows. This means that sets of generator dispatch that may have previously been infeasible due to the flow exceeding line constraints may be feasible, since the flows will be different and may meet line constraints. However, transmission switching is a mixed integer problem, which may have a very slow solution time. For economic switching, we examine a series of heuristics. We examine the congestion rent heuristic in detail and then examine many other heuristics at a higher level. Post-contingency corrective switching aims to fix issues in the power network after a line or generator outage. In Chapter 7, we show that using the sequential linear program with corrective switching helps solve voltage and excessive flow issues. (Abstract shortened by UMI.).

Fabrication of functional devices using soft lithography and unconventional micropatterning

NASA Astrophysics Data System (ADS)

Deng, Tao

In this thesis, I present part of our work in the fabrication of functional devices using soft lithography, and also describe unconventional micropatterning techniques involving photographic films. Soft lithography is a set of techniques that are complementary to photolithography, but not limited to planar patterning. It offers the capability of generating micro and nanostructures to a larger community than that familiar with conventional fabrication facilities. The first part of this thesis (chapter 1--4) focuses on the fabrication of microelectronic and micromagnetic devices. These successful demonstrations establish the compatibility of soft lithography with multilayer fabrication of functional devices, and open the door for the further development in these areas. Chapter 1 and 2 describe the use of microtransfer molding (muTM), micromolding in capillaries (MIMIC), and microcontact (muCP) for fabricating Schottky diodes and half-wave rectifier circuits. The fabrication processes involve multiple soft lithography steps and address the registrations between different layer of structures. Room temperature characteristics of these devices resemble those of diodes and rectifiers fabricated by photolithography. Chapter 3 and 4 demonstrate the fabrication of micromagnetic systems. In chapter 3, a one-dimensional bead motor is reported. Based on current-carrying wire systems, the bead motor can trap and transfer magnetic beads suspended in aqueous solutions. Chapter 4 shows a microfiltration system that uses arrays of nickel posts positioned in a polydimethylsiloxane (PDMS) microfluidic channel as the filtering elements. Turning on or off the magnetic field that is localized by these nickel posts can trap or release magnetic beads flowing by. The second part of this thesis (chapter 5--7) focuses on the development of unconventional microfabrication. The major objective underlying this work is to explore the simplest and most broadly available techniques that we could identify for forming patterns with features useful in functional microstructures. Chapter 5 and 6 describe the use of photographic films (microfiche and slide film) and transparencies printed using different printers as photomasks in the fabrication of PDMS stamps/molds for soft lithography. In chapter 6, we also compare different methods of generating microstructures using facilities readily and inexpensively available to chemistry and biology laboratories. Among the films and transparencies investigated, microfiche carries the highest resolution. It can generate structures as small as ˜10 mum in lateral dimensions. Chapter 7 shows a new rapid prototyping process for the fabrication of metallic microstructures using silver halide-based photographic film. The whole process, which involves photographic development and electrochemical deposition, only takes ˜2 hours, starting from a computer design file. It can generate electrically continuous structures with the smallest dimension of ˜30 mum in the plane of the film. The resulting structures---either supported on the film backing, or freed from it---are appropriate for use as passive, structural materials such as wire frames or meshes, and can also be used in microfluidic, microanalytical, and microelectromechanical systems (MEMS).

Coexistence: Threat to the Performance of Heterogeneous Network

NASA Astrophysics Data System (ADS)

Sharma, Neetu; Kaur, Amanpreet

2010-11-01

Wireless technology is gaining broad acceptance as users opt for the freedom that only wireless network can provide. Well-accepted wireless communication technologies generally operate in frequency bands that are shared among several users, often using different RF schemes. This is true in particular for WiFi, Bluetooth, and more recently ZigBee. These all three operate in the unlicensed 2.4 GHz band, also known as ISM band, which has been key to the development of a competitive and innovative market for wireless embedded devices. But, as with any resource held in common, it is crucial that those technologies coexist peacefully to allow each user of the band to fulfill its communication goals. This has led to an increase in wireless devices intended for use in IEEE 802.11 wireless local area networks (WLANs) and wireless personal area networks (WPANs), both of which support operation in the crowded 2.4-GHz industrial, scientific and medical (ISM) band. Despite efforts made by standardization bodies to ensure smooth coexistence it may occur that communication technologies transmitting for instance at very different power levels interfere with each other. In particular, it has been pointed out that ZigBee could potentially experience interference from WiFi traffic given that while both protocols can transmit on the same channel, WiFi transmissions usually occur at much higher power level. In this work, we considered a heterogeneous network and analyzed the impact of coexistence between IEEE 802.15.4 and IEEE 802.11b. To evaluate the performance of this network, measurement and simulation study are conducted and developed in the QualNet Network simulator, version 5.0.Model is analyzed for different placement models or topologies such as Random. Grid & Uniform. Performance is analyzed on the basis of characteristics such as throughput, average jitter and average end to end delay. Here, the impact of varying different antenna gain & shadowing model for this heterogeneous network is considered for the purpose of analysis.

Metal Complexes for Organic Optoelectronic Applications

NASA Astrophysics Data System (ADS)

Huang, Liang

Organic optoelectronic devices have drawn extensive attention by over the past two decades. Two major applications for Organic optoelectronic devices are efficient organic photovoltaic devices(OPV) and organic light emitting diodes (OLED). Organic Solar cell has been proven to be compatible with the low cost, large area bulk processing technology and processed high absorption efficiencies compared to inorganic solar cells. Organic light emitting diodes are a promising approach for display and solid state lighting applications. To improve the efficiency, stability, and materials variety for organic optoelectronic devices, several emissive materials, absorber-type materials, and charge transporting materials were developed and employed in various device settings. Optical, electrical, and photophysical studies of the organic materials and their corresponding devices were thoroughly carried out. In this thesis, Chapter 1 provides an introduction to the background knowledge of OPV and OLED research fields presented. Chapter 2 discusses new porphyrin derivatives- azatetrabenzylporphyrins for OPV and near infrared OLED applications. A modified synthetic method is utilized to increase the reaction yield of the azatetrabenzylporphyrin materials and their photophysical properties, electrochemical properties are studied. OPV devices are also fabricated using Zinc azatetrabenzylporphyrin as donor materials. Pt(II) azatetrabenzylporphyrin were also synthesized and used in near infra-red OLED to achieve an emission over 800 nm with reasonable external quantum efficiencies. Chapter 3, discusses the synthesis, characterization, and device evaluation of a series of tetradentate platinum and palladium complexesfor single doped white OLED applications and RGB white OLED applications. Devices employing some of the developed emitters demonstrated impressively high external quantum efficiencies within the range of 22%-27% for various emitter concentrations. And the palladium complex, i.e. Pd3O3, enables the fabrication of stable devices achieving nearly 1000h. at 1000cd/m2 without any outcoupling enhancement while simultaneously achieving peak external quantum efficiencies of 19.9%. Chapter 4 discusses tetradentate platinum and palladium complexes as deep blue emissive materials for display and lighting applications. The platinum complex PtNON, achieved a peak external quantum efficiency of 24.4 % and CIE coordinates of (0.18, 0.31) in a device structure designed for charge confinement and the palladium complexes Pd2O2 exhibited peak external quantum efficiency of up to 19.2%.

Terahertz and Microwave Devices Based on the Photo-Excited Low Dimensional Electronic System

DTIC Science & Technology

2015-03-11

Morphology of Thermally Annealed Copper Foils for Graphene Growth, Chemistry of Materials , (05 2013): 1643. doi : 10.1021/cm400032h R. G. Mani, J...connected specimens, IEEE Transactions on Nanotechnology, (01 2011): 179. doi : Jesús Iñarrea, R. Mani, W. Wegscheider. Sublinear radiation power...dependence of photoexcited resistance oscillations in two-dimensional electron systems, Physical Review B, (11 2010): 0. doi : 10.1103/PhysRevB

Development of Cell Phone Application for Blood Glucose Self-Monitoring Based on ISO/IEEE 11073 and HL7 CCD.

PubMed

Park, Hyun Sang; Cho, Hune; Kim, Hwa Sun

2015-04-01

The objectives of this research were to develop and evaluate a cell phone application based on the standard protocol for personal health devices and the standard information model for personal health records to support effective blood glucose management and standardized service for patients with diabetes. An application was developed for Android 4.0.3. In addition, an IEEE 11073 Manager, Medical Device Encoding Rule, and Bluetooth Health Device Profile Connector were developed for standardized health communication with a glucometer, and a Continuity of Care Document (CCD) Composer and CCD Parser were developed for CCD document exchange. The developed application was evaluated by five healthcare professionals and 87 users through a questionnaire comprising the following variables: usage intention, effort expectancy, social influence, facilitating condition, perceived risk, and voluntariness. As a result of the evaluation of usability, it was confirmed that the developed application is useful for blood glucose self-monitoring by diabetic patients. In particular, the healthcare professionals stated their own views that the application is useful to observe the trends in blood glucose change through the automatic function which records a blood glucose level measured using Bluetooth function, and the function which checks accumulated records of blood glucose levels. Also, a result of the evaluation of usage intention was 3.52 ± 0.42 out of 5 points. The application developed by our research team was confirmed by the verification of healthcare professionals that accurate feedback can be provided to healthcare professionals during the management of diabetic patients or education for glucose management.

Development of Cell Phone Application for Blood Glucose Self-Monitoring Based on ISO/IEEE 11073 and HL7 CCD

PubMed Central

Park, Hyun Sang; Cho, Hune

2015-01-01

Objectives The objectives of this research were to develop and evaluate a cell phone application based on the standard protocol for personal health devices and the standard information model for personal health records to support effective blood glucose management and standardized service for patients with diabetes. Methods An application was developed for Android 4.0.3. In addition, an IEEE 11073 Manager, Medical Device Encoding Rule, and Bluetooth Health Device Profile Connector were developed for standardized health communication with a glucometer, and a Continuity of Care Document (CCD) Composer and CCD Parser were developed for CCD document exchange. The developed application was evaluated by five healthcare professionals and 87 users through a questionnaire comprising the following variables: usage intention, effort expectancy, social influence, facilitating condition, perceived risk, and voluntariness. Results As a result of the evaluation of usability, it was confirmed that the developed application is useful for blood glucose self-monitoring by diabetic patients. In particular, the healthcare professionals stated their own views that the application is useful to observe the trends in blood glucose change through the automatic function which records a blood glucose level measured using Bluetooth function, and the function which checks accumulated records of blood glucose levels. Also, a result of the evaluation of usage intention was 3.52 ± 0.42 out of 5 points. Conclusions The application developed by our research team was confirmed by the verification of healthcare professionals that accurate feedback can be provided to healthcare professionals during the management of diabetic patients or education for glucose management. PMID:25995960

Compliance and Functional Testing of IEEE 1451.1 for NCAP-to-NCAP Communications in a Sensor Network

NASA Technical Reports Server (NTRS)

Figueroa, Jorge; Gurkan, Deniz; Yuan, X.; Benhaddou, D.; Liu, H.; Singla, A.; Franzl, R.; Ma, H.; Bhatt, S.; Morris, J.;

Improving the communication reliability of body sensor networks based on the IEEE 802.15.4 protocol.

PubMed

Gomes, Diogo; Afonso, José A

2014-03-01

Body sensor networks (BSNs) enable continuous monitoring of patients anywhere, with minimum constraints to daily life activities. Although the IEEE 802.15.4 and ZigBee(®) (ZigBee Alliance, San Ramon, CA) standards were mainly developed for use in wireless sensors network (WSN) applications, they are also widely used in BSN applications because of device characteristics such as low power, low cost, and small form factor. However, compared with WSNs, BSNs present some very distinctive characteristics in terms of traffic and mobility patterns, heterogeneity of the nodes, and quality of service requirements. This article evaluates the suitability of the carrier sense multiple access-collision avoidance protocol, used by the IEEE 802.15.4 and ZigBee standards, for data-intensive BSN applications, through the execution of experimental tests in different evaluation scenarios, in order to take into account the effects of contention, clock drift, and hidden nodes on the communication reliability. Results show that the delivery ratio may decrease substantially during transitory periods, which can last for several minutes, to a minimum of 90% with retransmissions and 13% without retransmissions. This article also proposes and evaluates the performance of the BSN contention avoidance mechanism, which was designed to solve the identified reliability problems. This mechanism was able to restore the delivery ratio to 100% even in the scenario without retransmissions.

46 CFR 111.60-3 - Cable application.

Code of Federal Regulations, 2010 CFR

2010-10-01

... IEEE 1580 must meet the provisions for cable application of section 24 of IEEE 45-2002 (both... incorporated by reference; see 46 CFR 110.10-1) must meet section 24 of IEEE 45-2002, except 24.6.1, 24.6.7... constructed according to IEEE 1580 must be applied in accordance with Table 25, Note 6, of IEEE 45-2002. (2...

Defining the IEEE-854 floating-point standard in PVS

NASA Technical Reports Server (NTRS)

Miner, Paul S.

1995-01-01

A significant portion of the ANSI/IEEE-854 Standard for Radix-Independent Floating-Point Arithmetic is defined in PVS (Prototype Verification System). Since IEEE-854 is a generalization of the ANSI/IEEE-754 Standard for Binary Floating-Point Arithmetic, the definition of IEEE-854 in PVS also formally defines much of IEEE-754. This collection of PVS theories provides a basis for machine checked verification of floating-point systems. This formal definition illustrates that formal specification techniques are sufficiently advanced that is is reasonable to consider their use in the development of future standards.

21 CFR 610.42 - Restrictions on use for further manufacture of medical devices.

Code of Federal Regulations, 2011 CFR

2011-04-01

... AND HUMAN SERVICES (CONTINUED) BIOLOGICS GENERAL BIOLOGICAL PRODUCTS STANDARDS Testing Requirements... devices. (a) In addition to labeling requirements in subchapter H of this chapter, when a medical device contains human blood or a blood component as a component of the final device, and the human blood or blood...

The theoretical study of passive and active optical devices via planewave based transfer (scattering) matrix method and other approaches

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhuo, Ye

2011-01-01

In this thesis, we theoretically study the electromagnetic wave propagation in several passive and active optical components and devices including 2-D photonic crystals, straight and curved waveguides, organic light emitting diodes (OLEDs), and etc. Several optical designs are also presented like organic photovoltaic (OPV) cells and solar concentrators. The first part of the thesis focuses on theoretical investigation. First, the plane-wave-based transfer (scattering) matrix method (TMM) is briefly described with a short review of photonic crystals and other numerical methods to study them (Chapter 1 and 2). Next TMM, the numerical method itself is investigated in details and developed inmore » advance to deal with more complex optical systems. In chapter 3, TMM is extended in curvilinear coordinates to study curved nanoribbon waveguides. The problem of a curved structure is transformed into an equivalent one of a straight structure with spatially dependent tensors of dielectric constant and magnetic permeability. In chapter 4, a new set of localized basis orbitals are introduced to locally represent electromagnetic field in photonic crystals as alternative to planewave basis. The second part of the thesis focuses on the design of optical devices. First, two examples of TMM applications are given. The first example is the design of metal grating structures as replacements of ITO to enhance the optical absorption in OPV cells (chapter 6). The second one is the design of the same structure as above to enhance the light extraction of OLEDs (chapter 7). Next, two design examples by ray tracing method are given, including applying a microlens array to enhance the light extraction of OLEDs (chapter 5) and an all-angle wide-wavelength design of solar concentrator (chapter 8). In summary, this dissertation has extended TMM which makes it capable of treating complex optical systems. Several optical designs by TMM and ray tracing method are also given as a full complement of this work.« less

Optimal placement of FACTS devices using optimization techniques: A review

NASA Astrophysics Data System (ADS)

Gaur, Dipesh; Mathew, Lini

2018-03-01

Modern power system is dealt with overloading problem especially transmission network which works on their maximum limit. Today’s power system network tends to become unstable and prone to collapse due to disturbances. Flexible AC Transmission system (FACTS) provides solution to problems like line overloading, voltage stability, losses, power flow etc. FACTS can play important role in improving static and dynamic performance of power system. FACTS devices need high initial investment. Therefore, FACTS location, type and their rating are vital and should be optimized to place in the network for maximum benefit. In this paper, different optimization methods like Particle Swarm Optimization (PSO), Genetic Algorithm (GA) etc. are discussed and compared for optimal location, type and rating of devices. FACTS devices such as Thyristor Controlled Series Compensator (TCSC), Static Var Compensator (SVC) and Static Synchronous Compensator (STATCOM) are considered here. Mentioned FACTS controllers effects on different IEEE bus network parameters like generation cost, active power loss, voltage stability etc. have been analyzed and compared among the devices.

A programmable positioning stepper-motor controller with a multibus/IEEE 796 compatible interface.

PubMed

Papoff, P; Ricci, D

1984-02-01

A programmable positioning stepper-motor controller, based on the Multibus/IEEE 796 standard interface, has been assembled by use of some intelligent and programmable integrated circuits. This controller, organized as a bus-slave unit, has been planned for local management of up to four stepper motors working simultaneously. The number of steps, the direction of rotation and the step-rate for the positioning of each motor are issued by the bus master microcomputer to the controller which handles all the required operations. Once each positioning has been performed, the controller informs the master by generating a proper bus-vectored interrupt. Displacements in up to 64,000 steps may be programmed with step-rates ranging from 0.1 to 6550 steps/sec. This device, for which only low-cost, high-performance components are required, can be successfully used in a wide range of applications and can be easily extended to control more than four stepper motors.

Enhancement Of Sensing Capabilities And Functionalization Of Optical Microresonators

NASA Astrophysics Data System (ADS)

Cocking, Alexander

Optical microresonators have been demonstrated to provide a large enhancement in electric field by containing an resonant mode in a very small volume. This resonant enhancement is proportional to the quality of the resonator, which for microspheres has been demonstrated to be on the order of 1010. These devices can be leveraged to greatly improve light-matter interaction and for this reason the theoretical background of optical microresonators is discussed in the second chapter. This includes the use of COMSOL Multiphysics to model the mode structure and scattering from different resonator geometries. The second chapter also contains details on the fabrication and experimental design of optical microresonators. This includes the fabrication of fiber tapers for evanescent wave coupling into the devices. Once the theoretical framework for utilizing resonators as tools for enhancement has been established in the second chapter, we progress to the discussion of the microbubble geometry and its potential for use as an on-chip sensor system. Topics covered include design, fabrication, and theoretical analysis of the mode structure in this geometry. Modal interaction with a liquid filled microbubble is demonstrated. Additionally, the use of microbubble resonators as highly accurate temperature sensors is demonstrated experimentally and theoretically. In chapter 4 we investigate the use of silica microspheres as sensing devices; specifically, using them for the purpose of sensing nano-particles and chemicals in incredibly minute quantities. In this section microresonators are demonstrated to provide enhancement to Raman scattering from nano-scale particles. This configuration retains the traditional sensing methods of resonators by observing mode shifting and splitting in the resonance spectrum, while adding in a label-free sensing ability to determine material composition on adhered micro and nanoparticles. The fifth chapter discusses the characterization of a new class of materials known as two dimensional materials (2D materials). Typically made from single atomic sheets of transition metal dichalcogenides, they are called two dimensional due to their incredibly small thickness. Monolayers of metal dichalcogenides offer large values for optical nonlinear susceptibility and can be used to generate highly efficient nonlinear optical phenomena. This chapter seeks to understand and describe the capabilities of these materials in a context of eventually integrating them into optical microresonators to create a new class of silica-based miniaturized nonlinear optical devices. The final chapter in this dissertation covers the proposed and in-progress work related to those topics already covered in previous chapters. This includes direct growth of transition metal dichalcogenides onto microsphere resonators to create narrow linewidth microscopic lasers. Another novel photonic device consists of a single mode optical fiber etched to expose the core onto which a monolayer of 2D material is adhered. This presents the capability to create a simple photonic device which can easily be integrated as a discrete optical component capable of producing guided photoluminescence or extremely high second harmonic generation. Finally, spectral holography is discussed as a potential tool to record the phase information of light traveling through optical microresonators, adhered particles, and directly grown 2D materials.

An Introduction to Descriptive Linguistics. Revised Edition.

ERIC Educational Resources Information Center

Gleason, H.A., Jr.

Beginning chapters of this volume define language and describe the sound, stress, and intonation systems of English. The body of the text explores extensively morphology, phonetics, phonemics, and the process of communication. Individual chapters detail such topics as morphemes, syntactic devices, grammatical systems, phonemic problems in language…

21 CFR 880.2930 - Apgar timer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... GENERAL HOSPITAL AND PERSONAL USE DEVICES General Hospital and Personal Use Monitoring Devices § 880.2930... requirements concerning records, and § 820.198 of this chapter, with respect to complaint files. [63 FR 59718...

21 CFR 880.2930 - Apgar timer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... GENERAL HOSPITAL AND PERSONAL USE DEVICES General Hospital and Personal Use Monitoring Devices § 880.2930... requirements concerning records, and § 820.198 of this chapter, with respect to complaint files. [63 FR 59718...

Optical, Electronic and Optoelectronic Material and Device Research

DTIC Science & Technology

1993-10-31

11, pp. 1275-1277 (September 1991). G. Griffel , W. K. Marshall, I. Grav6, and A. Yariv, "Frequency Control Using a Complex Effective Reflectivity in...Temperatures (5K)," Applied Physics Letters, vol. 58, no. 24, pp. 2752-2754 (June 1991). G. Griffel and A. Yariv, "Frequency Response and Tunability...of Grating- Assisted Directional Couplers," IEEE Journal of Quantum Electronics, vol. 27, no. 5, pp. 1115-1118 (May 1991). G. Griffel , H. Z. Chen, Ilan

An Electron-Beam Controlled Semiconductor Switch

DTIC Science & Technology

1989-11-01

of the Seventeenth Power Modulator Symposium, Seattle, WA, pp. 214-218. 1986. 21. Bovino , L., ’ioumans,R., Weiner, H., Burke, T . , "Optica lly... Bovino , R. Youmans, M. Weiner, and T. Burke, ’ ’Optically Co ntrolled Semiconducto r Switch for ~lulti-~legawatt Rep-Rated Pulse r s ," Conf. Record...p. 615. (II 1 W. N. Carr, IEEE Trans. Electron Devices, vol. ED-12, p. 531 , 1965. (121 T. Burke, M. Weiner. L. Bovino , and R. Youmans, in Proc

Field-Effect Spectroscopy of Interface States

DTIC Science & Technology

1988-12-31

ed.), Physics and Chemistry of Il-V Compound Semiconductor Interfaces, Plenum, New York, 1985, p. 327. HETEROJUNCTION AND DIELECTRICALLY INSULATED GATE...Electron Devices. voi. ED-29. pp. 1059-1064, 1982. chemistry , and physics from San Diego State Uni- 131 T. H. Mies, W. M. Paulson, and M. S...1982). 40. T. Y. Chang, R. F. Leheny, R. E. Nahory, E. Silberg , A. A. Ballman, E. A. Carid’ and C. J. Harrold, IEEE Electron. Dev. Lett. EDL- 3, 56

Barrier Engineered Quantum Dot Infrared Photodetectors

DTIC Science & Technology

2015-06-01

dual-color detectors using InAs/GaSb strained layer superlattices ." In Lester Eastman Conference on High Performance Devices (LEC), 2012, pp. 1-4. IEEE...Gautam, S. S. Krishna, E. P. Smith, S. Johnson, and S. Krishna. "Dual-band pBp detectors based on InAs/GaSb strained layer superlattices ." Infrared ...AFRL-RV-PS- AFRL-RV-PS- TR-2015-0111 TR-2015-0111 BARRIER ENGINEERED QUANTUM DOT INFRARED PHOTODETECTORS Sanjay Krishna Center for High Technology

Pseudorandom Number Generators for Mobile Devices: An Examination and Attempt to Improve Randomness

DTIC Science & Technology

2013-09-01

Notes in Computer Science (LNCS), Vol. 4341), (Hanoi, Vietnam: Springer, 2006), 260–270. 36 Simon R. Blackburn , “The Linear Complexity of the Self... Blackburn , Simon R. ‘The Linear Complexity of the Self-Shrinking Generator.” IEEE Trans. Inf. Theory, 45 (September 1999). Blum, Leonore, Manuel...afloat when the waters have been rough! xv THIS PAGE INTENTIONALLY LEFT BLANK xvi I. INTRODUCTION When the average man thinks about war and

Microcircuit Reliability Bibliography. Volume 4. 1976 Annual Reference Supplement. (Document Numbers 11045-11745)

DTIC Science & Technology

1976-04-01

State Electron- Res. Lab., Eindhoven, Neth.) icw 16, no. 12, 1315-20, Dec. 1973 ATMOS-AN ELECTRICALLY REPROGRAMMABLE READ-ONLY MEMORY DEVICE. IEEE Trans...transistor is described that can be used nular and array geometry contacts by as an electrically reprogrammable read- the pr~nciple of superposition. It is...digital tuning techniques for FM and typical automobile systems can be readily television, and pocket pagers. Tn. implemented by COS1440S monolithic

Precise parameterization of the recombination velocity at passivated phosphorus doped surfaces

NASA Astrophysics Data System (ADS)

Kimmerle, Achim; Momtazur Rahman, Md.; Werner, Sabrina; Mack, Sebastian; Wolf, Andreas; Richter, Armin; Haug, Halvard

2016-01-01

We investigate the surface recombination velocity Sp at the silicon-dielectric interface of phosphorus-doped surfaces for two industrially relevant passivation schemes for crystalline silicon solar cells. A broad range of surface dopant concentrations together with a high accuracy of evaluating the latter is achieved by incremental back-etching of the surface. The analysis of lifetime measurements and the simulation of the surface recombination consistently apply a set of well accepted models, namely, the Auger recombination by Richter et al. [Phys. Rev. B 86, 1-14 (2012)], the carrier mobility by Klaassen [Solid-State Electron. 35, 953-959 (1992); 35, 961-967 (1992)], the intrinsic carrier concentration for undoped silicon by Altermatt et al. [J. Appl. Phys. 93, 1598-1604 (2003)], and the band-gap narrowing by Schenk [J. Appl. Phys. 84, 3684-3695 (1998)]. The results show an increased Sp at textured in respect to planar surfaces. The obtained parameterizations are applicable in modern simulation tools such as EDNA [K. R. McIntosh and P. P. Altermatt, in Proceedings of the 35th IEEE Photovoltaic Specialists Conference, Honolulu, Hawaii, USA (2010), pp. 1-6], PC1Dmod [Haug et al., Sol. Energy Mater. Sol. Cells 131, 30-36 (2014)], and Sentaurus Device [Synopsys, Sentaurus TCAD, Zürich, Switzerland] as well as in the analytical solution under the assumption of local charge neutrality by Cuevas et al. [IEEE Trans. Electron Devices 40, 1181-1183 (1993)].

FACTS Devices Cost Recovery During Congestion Management in Deregulated Electricity Markets

NASA Astrophysics Data System (ADS)

Sharma, Ashwani Kumar; Mittapalli, Ram Kumar; Pal, Yash

2016-09-01

In future electricity markets, flexible alternating current transmission system (FACTS) devices will play key role for providing ancillary services. Since huge cost is involved for the FACTS devices placement in the power system, the cost invested has to be recovered in their life time for the replacement of these devices. The FACTS devices in future electricity markets can act as an ancillary services provider and have to be remunerated. The main contributions of the paper are: (1) investment recovery of FACTS devices during congestion management such as static VAR compensator and unified power flow controller along with thyristor controlled series compensator using non-linear bid curves, (2) the impact of ZIP load model on the FACTS cost recovery of the devices, (3) the comparison of results obtained without ZIP load model for both pool and hybrid market model, (4) secure bilateral transactions incorporation in hybrid market model. An optimal power flow based approach has been developed for maximizing social welfare including FACTS devices cost. The optimal placement of the FACTS devices have been obtained based on maximum social welfare. The results have been obtained for both pool and hybrid electricity market for IEEE 24-bus RTS.

14 CFR 121.289 - Landing gear: Aural warning device.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Landing gear: Aural warning device. 121.289... gear: Aural warning device. (a) Except for airplanes that comply with the requirements of § 25.729 of this chapter on or after January 6, 1992, each airplane must have a landing gear aural warning device...

14 CFR 121.289 - Landing gear: Aural warning device.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Landing gear: Aural warning device. 121.289... gear: Aural warning device. (a) Except for airplanes that comply with the requirements of § 25.729 of this chapter on or after January 6, 1992, each airplane must have a landing gear aural warning device...

14 CFR 121.289 - Landing gear: Aural warning device.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Landing gear: Aural warning device. 121.289... gear: Aural warning device. (a) Except for airplanes that comply with the requirements of § 25.729 of this chapter on or after January 6, 1992, each airplane must have a landing gear aural warning device...

14 CFR 121.289 - Landing gear: Aural warning device.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Landing gear: Aural warning device. 121.289... gear: Aural warning device. (a) Except for airplanes that comply with the requirements of § 25.729 of this chapter on or after January 6, 1992, each airplane must have a landing gear aural warning device...

14 CFR 121.289 - Landing gear: Aural warning device.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Landing gear: Aural warning device. 121.289... gear: Aural warning device. (a) Except for airplanes that comply with the requirements of § 25.729 of this chapter on or after January 6, 1992, each airplane must have a landing gear aural warning device...

Ambiguity Function Analysis for UMTS-Based Passive Multistatic Radar

DTIC Science & Technology

2014-04-16

Sandeep Gogineni, Member, IEEE, Muralidhar Rangaswamy, Fellow, IEEE, Brian D . Rigling, Senior Member, IEEE, and Arye Nehorai, Fellow, IEEE Abstract—There...muralidhar.rangaswamy@us.af. mil). B. D . Rigling is with the Department of Electrical Engineering, Wright State University, Dayton, OH 45435 USA (e-mail...ieeexplore.ieee.org. Digital Object Identifier 10.1109/TSP.2014.2318135 [1]–[9] and audio broadcast signals and FM radio [10], [11], satellite-based [12], and

Delay Analysis of GTS Bridging between IEEE 802.15.4 and IEEE 802.11 Networks for Healthcare Applications

PubMed Central

Mišić, Jelena; (Sherman) Shen, Xuemin

2009-01-01

We consider interconnection of IEEE 802.15.4 beacon-enabled network cluster with IEEE 802.11b network. This scenario is important in healthcare applications where IEEE 802.15.4 nodes comprise patient's body area network (BAN) and are involved in sensing some health-related data. BAN nodes have very short communication range in order to avoid harming patient's health and save energy. Sensed data needs to be transmitted to an access point in the ward room using wireless technology with higher transmission range and rate such as IEEE 802.11b. We model the interconnected network where IEEE 802.15.4-based BAN operates in guaranteed time slot (GTS) mode, and IEEE 802.11b part of the bridge conveys GTS superframe to the 802.11b access point. We then analyze the network delays. Performance analysis is performed using EKG traffic from continuous telemetry, and we discuss the delays of communication due the increasing number of patients. PMID:19107184

IEEE 802.11ah: A Technology to Face the IoT Challenge.

PubMed

Baños-Gonzalez, Victor; Afaqui, M Shahwaiz; Lopez-Aguilera, Elena; Garcia-Villegas, Eduard

2016-11-22

Since the conception of the Internet of things (IoT), a large number of promising applications and technologies have been developed, which will change different aspects in our daily life. This paper explores the key characteristics of the forthcoming IEEE 802.11ah specification. This future IEEE 802.11 standard aims to amend the IEEE 802.11 legacy specification to support IoT requirements. We present a thorough evaluation of the foregoing amendment in comparison to the most notable IEEE 802.11 standards. In addition, we expose the capabilities of future IEEE 802.11ah in supporting different IoT applications. Also, we provide a brief overview of the technology contenders that are competing to cover the IoT communications framework. Numerical results are presented showing how the future IEEE 802.11ah specification offers the features required by IoT communications, thus putting forward IEEE 802.11ah as a technology to cater the needs of the Internet of Things paradigm.

IEEE 802.11ah: A Technology to Face the IoT Challenge

PubMed Central

Baños-Gonzalez, Victor; Afaqui, M. Shahwaiz; Lopez-Aguilera, Elena; Garcia-Villegas, Eduard

2016-01-01

Since the conception of the Internet of things (IoT), a large number of promising applications and technologies have been developed, which will change different aspects in our daily life. This paper explores the key characteristics of the forthcoming IEEE 802.11ah specification. This future IEEE 802.11 standard aims to amend the IEEE 802.11 legacy specification to support IoT requirements. We present a thorough evaluation of the foregoing amendment in comparison to the most notable IEEE 802.11 standards. In addition, we expose the capabilities of future IEEE 802.11ah in supporting different IoT applications. Also, we provide a brief overview of the technology contenders that are competing to cover the IoT communications framework. Numerical results are presented showing how the future IEEE 802.11ah specification offers the features required by IoT communications, thus putting forward IEEE 802.11ah as a technology to cater the needs of the Internet of Things paradigm. PMID:27879688

Delay Analysis of GTS Bridging between IEEE 802.15.4 and IEEE 802.11 Networks for Healthcare Applications.

PubMed

Misić, Jelena; Sherman Shen, Xuemin

2009-01-01

We consider interconnection of IEEE 802.15.4 beacon-enabled network cluster with IEEE 802.11b network. This scenario is important in healthcare applications where IEEE 802.15.4 nodes comprise patient's body area network (BAN) and are involved in sensing some health-related data. BAN nodes have very short communication range in order to avoid harming patient's health and save energy. Sensed data needs to be transmitted to an access point in the ward room using wireless technology with higher transmission range and rate such as IEEE 802.11b. We model the interconnected network where IEEE 802.15.4-based BAN operates in guaranteed time slot (GTS) mode, and IEEE 802.11b part of the bridge conveys GTS superframe to the 802.11b access point. We then analyze the network delays. Performance analysis is performed using EKG traffic from continuous telemetry, and we discuss the delays of communication due the increasing number of patients.

Simulation Analysis of Wireless Power Transmission System for Biomedical Applications

NASA Astrophysics Data System (ADS)

Yang, Zhao; Wei, Zhiqiang; Chi, Haokun; Yin, Bo; Cong, Yanping

2018-03-01

In recent years, more and more implantable medical devices have been used in the medical field. Some of these devices, such as brain pacemakers, require long-term power support. The WPT(wireless power transmission) technology which is more convenient and economical than replacing the battery by surgery, has become the first choice of many patients. In this paper, we design a WPT system that can be used in implantable medical devices, simulate the transmission efficiency of the system in the air and in the head model, and simulate the SAR value when the system working in the head model. The results show that when implantation depth of the secondary coil is 3 mm, the efficiency of the system can reach 45%, and the maximum average SAR value is 2.19 W / kg, slightly higher than the standard of IEEE.

47 CFR 2.811 - Transmitters operated under part 73 of this chapter.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Transmitters operated under part 73 of this chapter. 2.811 Section 2.811 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Marketing of Radio-frequency Devices § 2...

47 CFR 2.811 - Transmitters operated under part 73 of this chapter.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Transmitters operated under part 73 of this chapter. 2.811 Section 2.811 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS Marketing of Radio-frequency Devices § 2...

47 CFR 24.2 - Other applicable rule parts.

Code of Federal Regulations, 2010 CFR

2010-10-01

... procedures concerning the marketing and importation of radio frequency devices, and for obtaining equipment... conditions relating to the marketing of part 15 devices. Unlicensed PCS devices operate under subpart D of... towers. (g) Part 20 of this chapter governs commercial mobile radio services. (h) Part 21. This part...

Engineering Design Handbook. Propellant Actuated Devices.

DTIC Science & Technology

1975-09-30

DA 016 716 ENGINEERING DESIGN HANDBOOK PROPELLANT ACTUATED DEVICES ARMY MATERIEL COMMAND ALEXANDRIA, VIRGINIA SEPTEMBER 1975 Best Available Copy... DESIGN HANDBOOK PROPELLANT ACTUATED DEVICES TABLE OF CONTENTS Paragraph Pae "LIST OF ILLUSTRATIONS .................. I LIST OF TABLES...Tramcmission in Systems ................. 2-18 References ............................... 2-18 CHAPTER 3. BASIC DESIGN CONSIDERATIONS 3-1 General

21 CFR 862.1710 - Total triiodothyronine test system.

Code of Federal Regulations, 2010 CFR

2010-04-01

... subpart E of part 807 of this chapter subject to the limitations in § 862.9. [52 FR 16122, May 1, 1987, as... (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test...

Information Transfer Ion Wireless Networks

DTIC Science & Technology

2010-07-01

conferences with proceed- ings to be made available online in the IEEE Xplore database, namely IFIP Wireless Days (WD 2008) at Dubai, UAE, and the...Poland, May 2008, pp. 61-64, IEEE Xplore , DOI = 10.1109/INFTECH. 2008.4621591. 2. J. Konorski, IEEE 802.11 LAN Capacity: Incentives and Incentive...2008, Dubai, UAE, Nov. 2008, IEEE Xplore DOI = 10.1109/WD.2008.4812857. 4. J. Konorski, QoS Provision in an Ad Hoc IEEE 802.11 WLAN: A Bayesian War

Information Transfer in Wireless Networks

DTIC Science & Technology

2010-07-01

conferences with proceed- ings to be made available online in the IEEE Xplore database, namely IFIP Wireless Days (WD 2008) at Dubai, UAE, and the...Poland, May 2008, pp. 61-64, IEEE Xplore , DOI = 10.1109/INFTECH. 2008.4621591. 2. J. Konorski, IEEE 802.11 LAN Capacity: Incentives and Incentive...2008, Dubai, UAE, Nov. 2008, IEEE Xplore DOI = 10.1109/WD.2008.4812857. 4. J. Konorski, QoS Provision in an Ad Hoc IEEE 802.11 WLAN: A Bayesian War

Advanced membrane devices. Interim report for October 1996--September 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laciak, D.V.; Langsam, M.; Lewnard, J.J.

1997-12-31

Under this Cooperative Agreement, Air Products and Chemicals, Inc. has continued to investigate and develop improved membrane technology for removal of carbon dioxide from natural gas. The task schedule for this reporting period included a detailed assessment of the market opportunity (Chapter 2), continued development and evaluation of membranes and membrane polymers (Chapter 3) and a detailed economic analysis comparing the potential of Air Products membranes to that of established acid gas removal processes (Chapter 4).

Reliable and energy-efficient communications for wireless biomedical implant systems.

PubMed

Ntouni, Georgia D; Lioumpas, Athanasios S; Nikita, Konstantina S

2014-11-01

Implant devices are used to measure biological parameters and transmit their results to remote off-body devices. As implants are characterized by strict requirements on size, reliability, and power consumption, applying the concept of cooperative communications to wireless body area networks offers several benefits. In this paper, we aim to minimize the power consumption of the implant device by utilizing on-body wearable devices, while providing the necessary reliability in terms of outage probability and bit error rate. Taking into account realistic power considerations and wireless propagation environments based on the IEEE P802.l5 channel model, an exact theoretical analysis is conducted for evaluating several communication scenarios with respect to the position of the wearable device and the motion of the human body. The derived closed-form expressions are employed toward minimizing the required transmission power, subject to a minimum quality-of-service requirement. In this way, the complexity and power consumption are transferred from the implant device to the on-body relay, which is an efficient approach since they can be easily replaced, in contrast to the in-body implants.

Improving acute care through use of medical device data.

PubMed

Kennelly, R J

1998-02-01

The Medical Information Bus (MIB) is a data communications standard for bedside patient connected medical devices. It is formally titled IEEE 1073 Standard for Medical Device Communications. MIB defines a complete seven layer communications stack for devices in acute care settings. All of the design trade-offs in writing the standard were taken to optimize performance in acute care settings. The key clinician based constraints on network performance are: (1) the network must be able to withstand multiple daily reconfigurations due to patient movement and condition changes; (2) the network must be 'plug-and-play' to allow clinicians to set up the network by simply plugging in a connector, taking no other actions; (3) the network must allow for unambiguous associations of devices with specific patients. A network of this type will be used by clinicians, thus giving complete, accurate, real time data from patient connected devices. This capability leads to many possible improvements in patient care and hospital cost reduction. The possible uses for comprehensive automatic data capture are only limited by imagination and creativity of clinicians adapting to the new hospital business paradigm.

IEEE Standards activities: A year in review. Annual activities report 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-09-01

For IEEE Standards and the constituency it serves, 1996 was a milestone year. It was a period that signaled the beginning of the Standards Program of the future. This program responds to worldwide standards issues and to the technical, market and competitive strategies of industrial sectors. It represents technological innovation, global participation in electrotechnology standards development and dedication to the on-going advancement and promotion of new concepts and technology. Instrumental in ensuring IEEE`s growth opportunities and leadership position in electrotechnology standards development and dissemination is IEEE membership. The value of members and their involvement in IEEE Standards is vital tomore » IEEE`s ability to continuously be the best professional association in the world. To fulfill this vision, IEEE set forth five goals -- increased globalization, career enhancement, electronic dissemination of existing products and services, organizational improvements and public responsibility. Key in the process for the achievement of these goals is to make certain that IEEE members are well informed about opportunities and benefits the present system of standardization offers, and what the future system will offer. With the member in mind, the Standards Board reviewed its strategic direction and operational structures, and its ability to deliver products and services that are needed now and, more importantly, that will be needed in the future. This Annual Activities Report provides a comprehensive picture of 1996 accomplishments and performance. It gives readers a broad picture of the Standards Board`s activities, the evolving role of IEEE Standards and the technological opportunities that the Board encourages.« less

10 CFR 431.447 - Department of Energy recognition of nationally recognized certification programs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... IEEE Std 112-2004 Test Methods A and B, IEEE Std 114-2010, CSA C390-10, and CSA C747 (incorporated by... IEEE Std 112-2004 Test Methods A and B, IEEE Std 114-2010, CSA C390-10, and CSA C747- (incorporated by...

10 CFR 431.447 - Department of Energy recognition of nationally recognized certification programs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... IEEE Std 112-2004 Test Methods A and B, IEEE Std 114-2010, CSA C390-10, and CSA C747 (incorporated by... IEEE Std 112-2004 Test Methods A and B, IEEE Std 114-2010, CSA C390-10, and CSA C747- (incorporated by...

Indium antimonide quantum well structures for electronic device applications

NASA Astrophysics Data System (ADS)

Edirisooriya, Madhavie

The electron effective mass is smaller in InSb than in any other III-V semiconductor. Since the electron mobility depends inversely on the effective mass, InSb-based devices are attractive for field effect transistors, magnetic field sensors, ballistic transport devices, and other applications where the performance depends on a high mobility or a long mean free path. In addition, electrons in InSb have a large g-factor and strong spin orbit coupling, which makes them well suited for certain spin transport devices. The first n-channel InSb high electron mobility transistor (HEMT) was produced in 2005 with a power-delay product superior to HEMTs with a channel made from any other III-V semiconductor. The high electron mobility in the InSb quantum-well channel increases the switching speed and lowers the required supply voltage. This dissertation focuses on several materials challenges that can further increase the appeal of InSb quantum wells for transistors and other electronic device applications. First, the electron mobility in InSb quantum wells, which is the highest for any semiconductor quantum well, can be further increased by reducing scattering by crystal defects. InSb-based heteroepitaxy is usually performed on semi-insulating GaAs (001) substrates due to the lack of a lattice matched semi-insulating substrate. The 14.6% mismatch between the lattice parameters of GaAs and InSb results in the formation of structural defects such as threading dislocations and microtwins which degrade the electrical and optical properties of InSb-based devices. Chapter 1 reviews the methods and procedures for growing InSb-based heterostructures by molecular beam epitaxy. Chapters 2 and 3 introduce techniques for minimizing the crystalline defects in InSb-based structures grown on GaAs substrates. Chapter 2 discusses a method of reducing threading dislocations by incorporating AlyIn1-ySb interlayers in an AlxIn1-xSb buffer layer and the reduction of microtwin defects by growth on GaAs substrates that are oriented 2° away from the [011] direction. Chapter 3 discusses designing InSb QW layer structures that are strain balanced. By applying these defect-reducing techniques, the electron mobility in InSb quantum wells at room temperature was significantly increased. For complementary logic technology, p-channel transistors with high mobility are equally as important as n-channel transistors. However, achieving a high hole mobility in III-V semiconductors is challenging. A controlled introduction of strain in the quantum-well material is an effective technique for enhancing the hole mobility beyond its value in bulk material. The strain reduces the hole effective mass by splitting the heavy hole and light hole valence bands. Chapter 4 discusses a successful attempt to realize p-type InSb quantum well structures. The biaxial strain applied via a relaxed metamorphic buffer resulted in a significantly higher room-temperature hole mobility and a record high low-temperature hole mobility. To demonstrate the usefulness of high mobility in a device structure, magnetoresistive devices were fabricated from remotely doped InSb QWs. Such devices have numerous practical applications such as position and speed sensors and as read heads in magnetic storage systems. In a magnetoresistive device composed of a series of shorted Hall bars, the magnetoresistance is proportional to the electron mobility squared for small magnetic fields. Hence, the high electron mobility in InSb QWs makes them highly preferable for geometrical magnetoresistors. Chapter 5 reports the fabrication and characterization of InSb quantum-well magnetoresistors. The excellent transport properties of the InSb QWs resulted in high room-temperature sensitivity to applied magnetic fields. Finally, Chapter 6 provides the conclusions obtained during this research effort, and makes suggestions for future work.

Analysis of ISO/IEEE 11073 built-in security and its potential IHE-based extensibility.

PubMed

Rubio, Óscar J; Trigo, Jesús D; Alesanco, Álvaro; Serrano, Luis; García, José

2016-04-01

The ISO/IEEE 11073 standard for Personal Health Devices (X73PHD) aims to ensure interoperability between Personal Health Devices and aggregators-e.g. health appliances, routers-in ambulatory setups. The Integrating the Healthcare Enterprise (IHE) initiative promotes the coordinated use of different standards in healthcare systems (e.g. Personal/Electronic Health Records, alert managers, Clinical Decision Support Systems) by defining profiles intended for medical use cases. X73PHD provides a robust syntactic model and a comprehensive terminology, but it places limited emphasis on security and on interoperability with IHE-compliant systems and frameworks. However, the implementation of eHealth/mHealth applications in environments such as health and fitness monitoring, independent living and disease management (i.e. the X73PHD domains) increasingly requires features such as secure connections to mobile aggregators-e.g. smartphones, tablets-, the sharing of devices among different users with privacy, and interoperability with certain IHE-compliant healthcare systems. This work proposes a comprehensive IHE-based X73PHD extension consisting of additive layers adapted to different eHealth/mHealth applications, after having analyzed the features of X73PHD (especially its built-in security), IHE profiles related with these applications and other research works. Both the new features proposed for each layer and the procedures to support them have been carefully chosen to minimize the impact on X73PHD, on its architecture (in terms of delays and overhead) and on its framework. Such implications are thoroughly analyzed in this paper. As a result, an extended model of X73PHD is proposed, preserving its essential features while extending them with added value. Copyright © 2016 Elsevier Inc. All rights reserved.

IEEE Std 730 Software Quality Assurance: Supporting CMMI-DEV v1.3, Product and Process Quality Assurance

DTIC Science & Technology

2011-05-27

frameworks 4 CMMI-DEV IEEE / ISO / IEC 15288 / 12207 Quality Assurance ©2011 Walz IEEE Life Cycle Processes & Artifacts • Systems Life Cycle Processes...TAG to ISO TC 176 Quality Management • Quality: ASQ, work experience • Software: three books, consulting, work experience • Systems: Telecom & DoD...and IEEE 730 SQA need to align. The P730 IEEE standards working group has expanded the scope of the SQA process standard to align with IS 12207

46 CFR 98.30-3 - Vessels carrying MPTs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... corrosion-resistant tag— (a) An inspection date for pressure relief devices and vacuum relief devices in... operated; and (c) A hydrostatic test date in accordance with paragraph (b) of § 64.83 of this chapter that...

Comments by the Chairman

NASA Astrophysics Data System (ADS)

Fouillat, Pascal

2013-08-01

The European Conference on Radiation and its Effects on Components and Systems (RADECS 2012) was held on September 24-28, 2012, in Biarritz, France. The latest advances in the field of radiation effects on electronic and photonic materials, devices, circuits, sensors, and systems, were presented and discussed. The conference featured a Technical Program, an Industrial Exhibit, and one day meeting on radiation ground effects held on September 24 (RADGROUND). The conference gathered 390 attendees, scientists and engineers from 26 countries, with a high participation of France (101), USA (80), Russia (50), Spain (28), Germany (28), and U.K. (25). Raoul Velazco, from TIMA Labs, was in charge of the Technical Program, assisted by a Technical Program Committee listed below and a pool ofmore than 150 reviewers which contributed maintain the high level of quality reached since many years by the RADECS conferences. The total number of contributions reached 201 and each paper received at least four reviews. There were 145 papers accepted and presented in the Oral Sessions (48), Poster Sessions (69), and Data Workshop (28). The scope of the conference encompassed technological processes and design techniques for producing radiation tolerant systems for space, aeronautical or terrestrial applications, as well as relevant methodologies for their characterization and qualification. The Conference Record, gathering all the papers compliant with IEEE quality standards and editorial rules, is available through the IEEE Xplore Digital Library. The paper candidates and selected for publication in the IEEE TRANSACTIONS ON NUCLEAR SCIENCE will be published in this special issue.

Heterojunction Structures for Photon Detector Applications

DTIC Science & Technology

2014-07-21

wavelength (SWIR), mid-wavelength (MWIR), and long wave- length-IR ( LWIR ), depending on the wavelength ranging from ~ 0.8 –5 µm, 5 – 30 µm and 30µm -1 mm...photovoltaic LWIR detection, Electron Devices, IEEE Transactions on, 39, pp. 234-241, 1992. [34] Kastalsky A, Duffield T, Allen S J, and Harbison J...62] Perera A G U, Silvestrov V G, Matsik S G, Liu H C, Buchanan M, Wasilewski Z R, and Ershov M, Nonuniform vertical charge transport and relaxation

Neutron Radiation Effects in Fiber Optics.

DTIC Science & Technology

1980-06-05

due to naturevs effects , the photophone as a device was doomed. However the principles of voice transmission by modulated ]iqht beams were not. From...AD-A091 661 NAVAL ACADEMY ANNAPOLIS NO F/S 20/6 NEUTRON RADIATION EFFECTS IN FIBER OPTICS.(U) N.N 80 M J MARSHFIELD NCLASSIFIED USNA-TSPR-107 MLE...34’I//E/////EE I ffffffffffffff /l-"lll/"."lmIii//2 //0 A TRIDENT SCHOLAR * PROJECT REPORT NO. 1im "NEUTRON RADIATION EFFECTS IN FIBE OPTICS UNITED

JFET/SOS (Junction Field-Effect Transistor/Silicon-on-Sapphire) Devices: Gamma-Radiation-Induced Effects.

DTIC Science & Technology

1988-03-01

Results, ATR-86A(8501)-1, The Aerospace Corporation: El Segundo, Calif. (20 May 1987). 3. D. Neaman , W. Shedd, and B. Buchanan, "Permanently Ionizing...Radiation Effects in Dielectrically Bounded Field-Effect Transistors," IEEE Trans.. Nucl. Sci. NS-20 [6], 158-165 (Decembe. 1973). 4. D. Neaman , W. Shedd...1974). 5. D. Neaman , W. Shedd, and B. Buchanan, "Silicon-Sapphire Interface Charge Trapping -- Effects of Sapphire Type and Epi Growth Conditions

IEEE International Symposium on Information Theory Held in San Diego, California on 14-19 January 1990

DTIC Science & Technology

1990-01-01

generator , and a set of three rules that insure the mimmum distance property. The coding scheme and the interleaving device will be described. The BER...point Padd method which matches the c.d f around zero and infinity. The advantage of this technique is that only low order moments are required. This is...accomplished by means of the intrinsic side information generated by an appropriate coding scheme . In this paper, we give sufficient conditions on channel

1992 IEEE Annual Conference on Nuclear and Space Radiation Effects, 29th, New Orleans, LA, July 13-17, 1992, Proceedings

NASA Technical Reports Server (NTRS)

Van Vonno, Nick W. (Editor)

1992-01-01

The papers presented in this volume provide an overview of recent theoretical and experimental research related to nuclear and space radiation effects. Topics dicussed include single event phenomena, radiation effects in particle detectors and associated electronics for accelerators, spacecraft charging, and space environments and effects. The discussion also covers hardness assurance and testing techniques, electromagnetic effects, radiation effects in devices and integrated circuits, dosimetry and radiation facilities, isolation techniques, and basic mechanisms.

Functionalization of Semiconductor Nanomaterials for Optoelectronic Devices And Components

DTIC Science & Technology

2015-03-04

conversion efficiency of InAs quantum dot solar cell by using a single layer anatase TiO2 anti-reflection coating,” R. Vasan, Y. F. Makableh, J. C...dx.doi.org/10.1557//opl.2013.742 9. “The Optimization of InP/ZnS Core/Shell Nanocrystals and TiO2 Nanotubes for Quantum Dot Sensitized Solar Cells ...Quantum Dots Solar Cells Performance,” J. C. Sarker, Y. F. Makableh, R. Vasan, S. Lee, M. O. Manasreh, and M. Benamara, IEEE J. Photovoltaic. (submitted

A Cascadable, Monolithic Laser/Modulator/Amplifier Transmitter.

DTIC Science & Technology

1997-03-01

for Use at 1.55um Wavelength", M. Fetterman , C-P Chao and S. R. Forrest, IEEE Photonics Technology Lett., 8, 69 (1995). 7. "Modelling of a...waveguide device using the Helmholtz beam propagation method", M. R. Fetterman and S. R. Forrest, Top. Mtg. on Integrated Photonics Research, Paper ThD4...Systems", OP. Chao, G. J. Shiau, M. Fetterman and S. R. Forrest, PSAA-V, Monterey CA (Jan., 1995). 13. "Photoluminescence Study of Excess Carrier

Automotive Research Center

Science.gov Websites

7, 2018, LA Times) Dr. Jason Siegel to chair IEEE Technical Committee on Automotive Controls (Feb 2018, IEEE) Dr. Anna Stefanopoulou on research of sustainable vehicle technologies (Jan 24, 2018, WEMU ) Stefanopoulou plenary at IEEE 56th CDC (Jan 17, 2018, ME) ARC Researchers at IEEE 56th Conf. Decision and

ARC Events

Science.gov Websites

chair IEEE Technical Committee on Automotive Controls (Feb 2018, IEEE) Dr. Anna Stefanopoulou on research of sustainable vehicle technologies (Jan 24, 2018, WEMU) Stefanopoulou plenary at IEEE 56th CDC (Jan 17, 2018, ME) ARC Researchers at IEEE 56th Conf. Decision and Control (Dec 12-14, 2017, CDC) ARC

42 CFR 414.1105 - Payment for Comprehensive Outpatient Rehabilitation Facility (CORF) services.

Code of Federal Regulations, 2011 CFR

2011-10-01

... equipment, prosthetic and orthotic devices, and drugs and biologicals. Supplies and durable medical... chapter and drugs and biologicals that are CORF services under § 410.100(k) of this chapter are paid the... under paragraphs (a) or (d). (d) Payment for drugs and biologicals. Drugs and biologicals that are CORF...

42 CFR 414.1105 - Payment for Comprehensive Outpatient Rehabilitation Facility (CORF) services.

Code of Federal Regulations, 2010 CFR

2010-10-01

... equipment, prosthetic and orthotic devices, and drugs and biologicals. Supplies and durable medical... chapter and drugs and biologicals that are CORF services under § 410.100(k) of this chapter are paid the... under paragraphs (a) or (d). (d) Payment for drugs and biologicals. Drugs and biologicals that are CORF...

Planning and Implementing Augmentative Communication Service Delivery, 2: Proceedings of the National Planners Conference on Assistive Device Service Delivery.

ERIC Educational Resources Information Center

Coston, Caroline A., Ed.

The document consists of 30 author contributed chapters concerned with augmentative communication service delivery. Chapter titles and authors are: "Communication Options for Persons Who Cannot Speak: Planning for Service Delivery" (David Beukelman); "Planning Service Delivery Systems" (Roland Hahn II); "Planning Ohio's…

Using the Earth to Heat and Cool Homes.

ERIC Educational Resources Information Center

Thomas, Stephen G.

The heat collecting capacity of the earth and or the earth's ground waters and surface waters exist as potential energy sources for home heating and cooling. Techniques and devices associated with use of the earth's thermal energy capabilities are presented and evaluated in this four-chapter report. Included in these chapters are: (1) descriptions…

Development of conductometric biosensors based on alkaline phosphatases for the water quality control

NASA Astrophysics Data System (ADS)

Berezhetskyy, A.

2008-09-01

Researches are focused on the elaboration of enzymatic microconductometric device for heavy metal ions detection in water solutions. The manuscript includes a general introduction, the first chapter contains bibliographic review, the second chapter described the fundamentals of conductometric transducers, the third chapter examining the possibility to create and to optimize conductometric biosensor based on bovine alkaline phosphatase for heavy metals ions detection, the fourth chapter devoted to creation and optimization of conductometric biosensor based on alkaline phosphatase active microalgae and sol gel technology, the last chapter described application of the proposed algal biosensor for measurements of heavy metal ions toxicity of waste water, general conclusions stating the progresses achieved in the field of environmental monitoring

PREFACE: I International Scientific School Methods of Digital Image Processing in Optics and Photonics

NASA Astrophysics Data System (ADS)

Gurov, I. P.; Kozlov, S. A.

2014-09-01

The first international scientific school "Methods of Digital Image Processing in Optics and Photonics" was held with a view to develop cooperation between world-class experts, young scientists, students and post-graduate students, and to exchange information on the current status and directions of research in the field of digital image processing in optics and photonics. The International Scientific School was managed by: Saint Petersburg National Research University of Information Technologies, Mechanics and Optics (ITMO University) - Saint Petersburg (Russia) Chernyshevsky Saratov State University - Saratov (Russia) National research nuclear University "MEPHI" (NRNU MEPhI) - Moscow (Russia) The school was held with the participation of the local chapters of Optical Society of America (OSA), the Society of Photo-Optical Instrumentation Engineers (SPIE) and IEEE Photonics Society. Further details, including topics, committees and conference photos are available in the PDF

14 CFR 61.156 - Training requirements: Airplane category-multiengine class rating or airplane type rating...

Code of Federal Regulations, 2014 CFR

2014-01-01

... simulation training device qualified under part 60 of this chapter that represents a multiengine turbine... completed in a Level 4 or higher flight simulation training device. The training must include the following...

Adaptive, Tactical Mesh Networking: Control Base MANET Model

DTIC Science & Technology

2010-09-01

pp. 316–320 Available: IEEE Xplore , http://ieeexplore.ieee.org [Accessed: June 9, 2010]. [5] N. Sidiropoulos, “Multiuser Transmit Beamforming...Mobile Mesh Segments of TNT Testbed .......... 11 Figure 5. Infrastructure and Ad Hoc Mode of IEEE 802.11................................ 13 Figure...6. The Power Spectral Density of OFDM................................................ 14 Figure 7. A Typical IEEE 802.16 Network

2012 Special NSREC Issue of the IEEE Transactions on Nuclear Science Comments by the Editors

NASA Astrophysics Data System (ADS)

Schwank, Jim; Brown, Dennis; Girard, Sylvain; Gouker, Pascale; Gerardin, Simone; Quinn, Heather; Barnaby, Hugh

2012-12-01

The December 2012 special issue of the IEEE Transactions on Nuclear Science contains selected papers from the 49th annual IEEE International Nuclear and Space Radiation Effects Conference (NSREC) held July 16-20, 2012, in Miami, Florida USA. 95 papers presented at the 2012 NSREC were submitted for consideration for this year’s special issue. Those papers that appear in this special issue were able to successfully complete the review process before the deadline for the December issue. A few additional papers may appear in subsequent issues of the TRANSACTIONS. This publication is the premier archival journal for research on space and nuclear radiation effects in materials, devices, circuits, and systems. This distinction is the direct result of the conscientious efforts of both the authors, who present and document their work, and the reviewers, who selflessly volunteer their time and talent to help review the manuscripts. Each paper in this journal has been reviewed by experts selected by the editors for their expertise and knowledge of the particular subject areas. The peer review process for a typical technical journal generally takes six months to one year to complete. To publish this special issue of the IEEE Transactions on Nuclear Science (in December), the review process, from initial submission to final form, must be completed in about 10 weeks. Because of the short schedule, both the authors and reviewers are required to respond very quickly. The reviewers listed on the following pages contributed vitally to this quick-turn review process.We would like to express our sincere appreciation to each of them for accepting this difficult, but critical role in the process. To provide consistent reviews of papers throughout the year, the IEEE Transactions on Nuclear Science relies on a year-round editorial board that manages reviews for submissions throughout the year to the TRANSACTIONS in the area of radiation effects. The review process is managed by a Senior Editor and six Associate Editors who are technically knowledgeable in one or more specializations and are experienced in the publication process. This editorial process works very well. With twice the number of editors as previously used for overseeing the review process, each editor is able to devote more time to individual papers.

Regulatory Barriers Blocking Standardization of Interoperability

PubMed Central

Zhong, Daidi; Kirwan, Michael J

2013-01-01

Developing and implementing a set of personal health device interoperability standards is key to cultivating a healthy global industry ecosystem. The standardization organizations, including the Institute of Electrical and Electronics Engineers 11073 Personal Health Device Workgroup (IEEE 11073-PHD WG) and Continua Health Alliance, are striving for this purpose. However, factors like the medial device regulation, health policy, and market reality have placed non-technical barriers over the adoption of technical standards throughout the industry. These barriers have significantly impaired the motivations of consumer device vendors who desire to enter the personal health market and the overall success of personal health industry ecosystem. In this paper, we present the affect that these barriers have placed on the health ecosystem. This requires immediate action from policy makers and other stakeholders. The current regulatory policy needs to be updated to reflect the reality and demand of consumer health industry. Our hope is that this paper will draw wide consensus amongst its readers, policy makers, and other stakeholders. PMID:25098204

Regulatory barriers blocking standardization of interoperability.

PubMed

Zhong, Daidi; Kirwan, Michael J; Duan, Xiaolian

2013-07-12

Developing and implementing a set of personal health device interoperability standards is key to cultivating a healthy global industry ecosystem. The standardization organizations, including the Institute of Electrical and Electronics Engineers 11073 Personal Health Device Workgroup (IEEE 11073-PHD WG) and Continua Health Alliance, are striving for this purpose. However, factors like the medial device regulation, health policy, and market reality have placed non-technical barriers over the adoption of technical standards throughout the industry. These barriers have significantly impaired the motivations of consumer device vendors who desire to enter the personal health market and the overall success of personal health industry ecosystem. In this paper, we present the affect that these barriers have placed on the health ecosystem. This requires immediate action from policy makers and other stakeholders. The current regulatory policy needs to be updated to reflect the reality and demand of consumer health industry. Our hope is that this paper will draw wide consensus amongst its readers, policy makers, and other stakeholders.

Conceptualization of an exoskeleton Continuous Passive Motion(CPM) device using a link structure.

PubMed

Kim, Kyu-Jung; Kang, Min-Sung; Choi, Youn-Sung; Han, Jungsoo; Han, Changsoo

2011-01-01

This study is about developing an exoskeleton Continuous Passive Motion (CPM) with the same Range of Motion (ROM) and instant center of rotation as the human knee. The key feature in constructing a CPM is an accurate alignment with the human knee joint enabling it to deliver the same movements as the actual body on the CPM. In this research, we proposed an exoskeleton knee joint through kinematic interpretation, measured the knee joint torque generated while using a CPM and applied it to the device. Thus, this new exoskeleton type CPM will allow precise alignment with the human knee joint, and follow the same ROM as the human knee in any position. © 2011 IEEE

Interoperable and standard e-Health solution over Bluetooth.

PubMed

Martinez, I; Del Valle, P; Munoz, P; Trigo, J D; Escayola, J; Martínez-Espronceda, M; Muñoz, A; Serrano, L; Garcia, J

2010-01-01

The new paradigm of e-Health demands open sensors and middleware components that permit transparent integration and end-to-end interoperability of new personal health devices. The use of standards seems to be the internationally adopted way to solve these problems. This paper presents the implementation of an end-to-end standards-based e-Health solution. This includes ISO/IEEE11073 standard for the interoperability of the medical devices in the patient environment and EN13606 standard for the interoperable exchange of the Electronic Healthcare Record. The design strictly fulfills all the technical features of the most recent versions of both standards. The implemented prototype has been tested in a laboratory environment to demonstrate its feasibility for its further transfer to the healthcare system.

One-dimensional nanostructures for novel biosensor and transparent electronics applications

NASA Astrophysics Data System (ADS)

Chang, Hsiao-Kang

This dissertation presents one-dimensional nanostructures for novel biosensors and transparent electronics applications. In chapter 1, background information regarding nanomaterials studied in this dissertation is described. In chapter 2, I describe the first application of antibody mimic proteins (AMPs) in the field of nanobiosensors. In2O3 nanowire based biosensors have been configured with an AMP (Fibronectin, Fn) to detect nucleocapsid (N) protein, a biomarker for severe acute respiratory syndrome (SARS). Using these devices, N protein was detected at sub-nanomolar concentration in the presence of 44 microM bovine serum albumin as a background. Furthermore, the binding constant of the AMP to Fn was determined from the concentration dependence of the response of our biosensors. In chapter 3, I demonstrate an In2O3 nanowire-based biosensing system that is capable of performing rapid, label-free, electrical detection of cancer biomarkers directly from human whole blood collected by a finger prick. Detection of multiple cancer biomarkers with high reliability at clinically meaningful concentrations from whole blood collected by a finger prick using this sensing system is demonstrated. In chapter 4, I introduce a top-down nanobiosensor based on polysilicon nanoribbon with enhanced yield and device uniformity. The polysilicon nanoribbon devices can be fabricated by conventional photolithography with only easily available materials and equipments required, thus results in great time and cost efficiency as well as scalability. The devices show great response to pH changes with a wide dynamic range and high sensitivity. Biomarker detection is also demonstrated with clinically relevant sensitivity. Such results suggest that polysilicon nanoribbon devices exhibit great potential toward a highly efficient, reliable and sensitive biosensing platform. In chapter 5, I demonstrate the first printed nanobiosensor application based on separated semiconducting single-walled carbon nanotubes. The printed nanosensors exhibit reliable sensing to pH variation. We have successfully achieved the detection of Estradial, a commonly used hormone biomarker, as a proof of concept for using printed nanobiosensors on disease diagnosis. High-performance fully transparent thin-film transistors (TTFTs) on both rigid and flexible substrates with transfer printed aligned nanotubes as the active channel and indium-tin oxide as the source, drain and gate electrodes is reported in chapter 6. Such transistors are fabricated through low temperature processing, which allows device fabrication even on flexible substrates. Transparent transistors with high effective mobilities (˜1,300 cm2V -1s-1) were first demonstrated on glass substrates via engineering of the source and drain contacts, and high on/off ratio (3 x 104) was achieved using electrical breakdown. In addition, flexible TTFTs with good transparency were also fabricated and successfully operated under bending up to 120°. All of the devices showed good transparency (˜80% on average). The transparent transistors were further utilized to construct a fully transparent and flexible logic inverter on a plastic substrate, and also used to control commercial GaN light-emitting diodes (LEDs) with light intensity modulation of 103. Our results suggest that aligned nanotubes have great potential to work as building blocks for future transparent electronics. In chapter 7, a summary of all topics in this dissertation is described. Future work regarding the nanobiosensor project is also proposed.

Design and simulation of printed spiral coil used in wireless power transmission systems for implant medical devices.

PubMed

Wu, Wei; Fang, Qiang

2011-01-01

Printed Spiral Coil (PSC) is a coil antenna for near-field wireless power transmission to the next generation implant medical devices. PSC for implant medical device should be power efficient and low electromagnetic radiation to human tissues. We utilized a physical model of printed spiral coil and applied our algorithm to design PSC operating at 13.56 MHz. Numerical and electromagnetic simulation of power transfer efficiency of PSC in air medium is 77.5% and 71.1%, respectively. The simulation results show that the printed spiral coil which is optimized for air will keep 15.2% power transfer efficiency in human subcutaneous tissues. In addition, the Specific Absorption Ratio (SAR) for this coil antenna in subcutaneous at 13.56 MHz is below 1.6 W/Kg, which suggests this coil is implantable safe based on IEEE C95.1 safety guideline.

New Layered Materials and Functional Nanoelectronic Devices

NASA Astrophysics Data System (ADS)

Yu, Jaeeun

This thesis introduces functional nanomaterials including superatoms and carbon nanotubes (CNTs) for new layered solids and molecular devices. Chapters 1-3 present how we incorporate superatoms into two-dimensional (2D) materials. Chapter 1 describes a new and simple approach to dope transition metal dichalcogenides (TMDCs) using the superatom Co6Se8(PEt3)6 as the electron dopant. Doping is an effective method to modulate the electrical properties of materials, and we demonstrate an electron-rich cluster can be used as a tunable and controllable surface dopant for semiconducting TMDCs via charge transfer. As a demonstration of the concept, we make a p-n junction by patterning on specific areas of TMDC films. Chapter 2 and Chapter 3 introduce new 2D materials by molecular design of superatoms. Traditional atomic van der Waals materials such as graphene, hexagonal boron-nitride, and TMDCs have received widespread attention due to the wealth of unusual physical and chemical behaviors that arise when charges, spins, and vibrations are confined to a plane. Though not as widespread as their atomic counterparts, molecule-based layered solids offer significant benefits; their structural flexibility will enable the development of materials with tunable properties. Chapter 2 describes a layered van der Waals solid self-assembled from a structure-directing building block and C60 fullerene. The resulting crystalline solid contains a corrugated monolayer of neutral fullerenes and can be mechanically exfoliated. Chapter 3 describes a new method to functionalize electroactive superatoms with groups that can direct their assembly into covalent and non-covalent multi-dimensional frameworks. We synthesized Co6Se8[PEt2(4-C6H4COOH)]6 and found that it forms two types of crystalline assemblies with Zn(NO3)2, one is a three-dimensional solid and the other consists of stacked layers of two-dimensional sheets. The dimensionality is controlled by subtle changes in reaction conditions. CNT-based field-effect transistor (FETs), in which a single molecule spans an oxidatively cut gap in the CNT, provide a versatile, ground-state platform with well-defined electrical contacts. For statistical studies of a variety of small molecule bridges, Chapter 4 presents a novel fabrication method to produce hundreds of FETs on one single carbon nanotube. A large number of devices allows us to study the stability and uniformity of CNT FET properties. Moreover, the new platform also enables a quantitative analysis of molecular devices. In particular, we used CNT FETs for studying DNA-mediated charge transport. DNA conductance was measured by connecting DNA molecules of varying lengths to lithographically cut CNT FETs.

Novel Polymeric Dielectric Materials for the Additive Manufacturing of Microwave Devices

NASA Astrophysics Data System (ADS)

O'Keefe, Shamus E.

The past decade has seen a rapid increase in the deployment of additive manufacturing (AM) due to the perceived benefits of lower cost, higher quality, and a smaller environmental footprint. And while the hardware behind most of AM processes is mature, the study and development of material feedstock(s) are in their infancy, particularly so for niche areas. In this dissertation, we look at novel polymeric materials to support AM for microwave devices. Chapter 1 provides an overview of the benefits of AM, followed by the specific motivation for this work, and finally a scope defining the core objectives. Chapter 2 delves into a higher-level background of dielectric theory and includes a brief overview of the two common dielectric spectroscopy techniques used in this work. The remaining chapters, summarized below, describe experiments in which novel polymeric materials were developed and their microwave dielectric properties measured. Chapter 3 describes the successful synthesis of polytetrafluroethylene (PTFE)/polyacrylate (PA) core-shell nanoparticles and their measured microwave dielectric properties. PTFE/PA core-shell nanoparticles with spherical morphology were successfully made by aerosol deposition followed by a brief annealing. The annealing temperature is closely controlled to exceed the glass transition (Tg) of the PA shell yet not exceed the Tg of the PTFE core. Furthermore, the annealing promotes coalescence amongst the PA shells of neighboring nanoparticles and results in the formation of a contiguous PA matrix that has excellent dispersion of PTFE cores. The measured dielectric properties agree well with theoretical predictions and suggest the potential of this material as a feedstock for AM microwave devices. Chapter 4 delves into the exploration of various polyimide systems with the aim of replacing the PA in the previously studied PTFE/PA core-shell nanoparticles. Fundamental relationships between polymer attributes (flexibility/rigidity and functional groups) and dielectric properties were explored. The results indicate that backbone rigidity and the inclusion of fluorine lead to excellent dielectric properties, however, often at the expense of mechanical properties. Chapter 5 explores the optimization of PTFE core-shell nanoparticles via a novel PTFE/polyimide (PI) core-shell nanoparticle. PTFE/PI core-shell nanoparticles were synthesized via electrostatic interaction between the PTFE cores and a PI precursor, poly(amic) acid salt (PAAS). The PAAS is converted to PI by thermal imidization. The PI has properties superior to those of PA for microwave applications and the results suggest the promise of PTFE/PI core-shell nanoparticles for use in AM of microwave devices. Chapter 6 describes the first report of on actively-tunable microwave substrate made possible by a semiconducting polymer composite blend. The composite blend is comprised of poly(3-hexylthiophene) (P3HT) as the semiconducting polymer and [6,6]-Phenyl C61 butyric acid methyl ester (PCBM) while the remainder of the composite is comprised of a low dielectric constant polymer polydimethylsiloxane (PDMS). When subjected to photo excitation (white light, spectrum centered at 532 nm), the composite exhibits a tunability of the permittivity up to 20%. The results suggest strong promise for the use of semiconducting polymers in actively-tunable microwave devices. Finally, Chapter 7 presents a summary of the salient conclusions of the reported studies. The chapter concludes with a few brief remarks of my personal experience as a non-traditional student and the challenges therein.

Multimodal Task-Driven Dictionary Learning for Image Classification

DTIC Science & Technology

2015-12-18

1 Multimodal Task-Driven Dictionary Learning for Image Classification Soheil Bahrampour, Student Member, IEEE, Nasser M. Nasrabadi, Fellow, IEEE...Asok Ray, Fellow, IEEE, and W. Kenneth Jenkins, Life Fellow, IEEE Abstract— Dictionary learning algorithms have been suc- cessfully used for both...reconstructive and discriminative tasks, where an input signal is represented with a sparse linear combination of dictionary atoms. While these methods are

Validating the Test Procedures Described in UL 1741 SA and IEEE P1547.1: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mahmud, Rasel; Hoke, Anderson F; Narang, David J

This paper investigates the test procedures specified in UL 1741 SA and the upcoming revision to IEEE P1547.1. A 550 kVA photovoltaic inverter was chosen for the tests. This research reveals some of key the components to consider while doing certification tests for UL 1741 SA and IEEE P1547.1. This paper also identifies some issues requiring consideration for future releases of the standard, i.e. IEEE P1547.1. This paper investigates the test procedures specified in UL 1741 SA and the upcoming revision to IEEE P1547.1. A 550 kVA photovoltaic inverter was chosen for the tests. This research reveals some of keymore » the components to consider while doing certification tests for UL 1741 SA and IEEE P1547.1. This paper also identifies some issues requiring consideration for future releases of the standard, i.e. IEEE P1547.1.« less

Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings

PubMed Central

Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

2011-01-01

This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices. PMID:22043254

Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings.

PubMed

Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

2011-01-01

This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices.

Using off-the-shelf medical devices for biomedical signal monitoring in a telemedicine system for emergency medical services.

PubMed

Thelen, Sebastian; Czaplik, Michael; Meisen, Philipp; Schilberg, Daniel; Jeschke, Sabina

2015-01-01

In order to study new methods of telemedicine usage in the context of emergency medical services, researchers need to prototype integrated telemedicine systems. To conduct a one-year trial phase-intended to study a new application of telemedicine in German emergency medical services-we used off-the-shelf medical devices and software to realize real-time patient monitoring within an integrated telemedicine system prototype. We demonstrate its feasibility by presenting the integrated real-time patient monitoring solution, by studying signal delay and transmission robustness regarding changing communication channel characteristics, and by evaluating issues reported by the physicians during the trial phase. Where standards like HL7 and the IEEE 11073 family are intended to enable interoperability of product grade medical devices, we show that research prototypes benefit from the use of web technologies and simple device interfaces, as they simplify product development for a manufacturer and ease integration efforts for research teams. Embracing this approach for the development of new medical devices eases the constraint to use off-the-shelf products for research trials investigating innovative use of telemedicine.

33 CFR 156.120 - Requirements for transfer.

Code of Federal Regulations, 2011 CFR

2011-07-01

... closure devices required by §§ 154.520 and 155.805 of this chapter; (g) The transfer system is attached to... hose has no unrepaired loose covers, kinks, bulges, soft spots, or any other defect which would permit....810(g) of this chapter or 46 CFR 39.40-3(c) is fitted between the facility vapor connection and the...

40 CFR 156.204 - Modification and waiver of requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... accordance with § 154.25(c) of this chapter that a pesticide should be placed in Special Review because the pesticide meets or exceeds the criteria for human health effects of § 154.7(a)(1)(2) or (6) of this chapter...) PESTICIDE PROGRAMS LABELING REQUIREMENTS FOR PESTICIDES AND DEVICES Worker Protection Statements § 156.204...

40 CFR 156.204 - Modification and waiver of requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... accordance with § 154.25(c) of this chapter that a pesticide should be placed in Special Review because the pesticide meets or exceeds the criteria for human health effects of § 154.7(a)(1)(2) or (6) of this chapter...) PESTICIDE PROGRAMS LABELING REQUIREMENTS FOR PESTICIDES AND DEVICES Worker Protection Statements § 156.204...

40 CFR 156.204 - Modification and waiver of requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... accordance with § 154.25(c) of this chapter that a pesticide should be placed in Special Review because the pesticide meets or exceeds the criteria for human health effects of § 154.7(a)(1)(2) or (6) of this chapter...) PESTICIDE PROGRAMS LABELING REQUIREMENTS FOR PESTICIDES AND DEVICES Worker Protection Statements § 156.204...

40 CFR 156.204 - Modification and waiver of requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... accordance with § 154.25(c) of this chapter that a pesticide should be placed in Special Review because the pesticide meets or exceeds the criteria for human health effects of § 154.7(a)(1)(2) or (6) of this chapter...) PESTICIDE PROGRAMS LABELING REQUIREMENTS FOR PESTICIDES AND DEVICES Worker Protection Statements § 156.204...

40 CFR 156.204 - Modification and waiver of requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... accordance with § 154.25(c) of this chapter that a pesticide should be placed in Special Review because the pesticide meets or exceeds the criteria for human health effects of § 154.7(a)(1)(2) or (6) of this chapter...) PESTICIDE PROGRAMS LABELING REQUIREMENTS FOR PESTICIDES AND DEVICES Worker Protection Statements § 156.204...

Precise parameterization of the recombination velocity at passivated phosphorus doped surfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kimmerle, Achim, E-mail: achim-kimmerle@gmx.de; Momtazur Rahman, Md.; Werner, Sabrina

We investigate the surface recombination velocity S{sub p} at the silicon-dielectric interface of phosphorus-doped surfaces for two industrially relevant passivation schemes for crystalline silicon solar cells. A broad range of surface dopant concentrations together with a high accuracy of evaluating the latter is achieved by incremental back-etching of the surface. The analysis of lifetime measurements and the simulation of the surface recombination consistently apply a set of well accepted models, namely, the Auger recombination by Richter et al. [Phys. Rev. B 86, 1–14 (2012)], the carrier mobility by Klaassen [Solid-State Electron. 35, 953–959 (1992); 35, 961–967 (1992)], the intrinsic carriermore » concentration for undoped silicon by Altermatt et al. [J. Appl. Phys. 93, 1598–1604 (2003)], and the band-gap narrowing by Schenk [J. Appl. Phys. 84, 3684–3695 (1998)]. The results show an increased S{sub p} at textured in respect to planar surfaces. The obtained parameterizations are applicable in modern simulation tools such as EDNA [K. R. McIntosh and P. P. Altermatt, in Proceedings of the 35th IEEE Photovoltaic Specialists Conference, Honolulu, Hawaii, USA (2010), pp. 1–6], PC1Dmod [Haug et al., Sol. Energy Mater. Sol. Cells 131, 30–36 (2014)], and Sentaurus Device [Synopsys, Sentaurus TCAD, Zürich, Switzerland] as well as in the analytical solution under the assumption of local charge neutrality by Cuevas et al. [IEEE Trans. Electron Devices 40, 1181–1183 (1993)].« less

10 CFR 30.32 - Application for specific licenses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... material in the form of a sealed source or in a device that contains the sealed source must either— (1) Identify the source or device by manufacturer and model number as registered with the Commission under § 32.210 of this chapter, with an Agreement State, or for a source or a device containing radium-226 or...

10 CFR 30.32 - Application for specific licenses.

Code of Federal Regulations, 2010 CFR

2010-01-01

... material in the form of a sealed source or in a device that contains the sealed source must either— (1) Identify the source or device by manufacturer and model number as registered with the Commission under § 32.210 of this chapter, with an Agreement State, or for a source or a device containing radium-226 or...

46 CFR 169.681 - Disconnect switches and devices.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 7 2012-10-01 2012-10-01 false Disconnect switches and devices. 169.681 Section 169.681... Less Than 100 Gross Tons § 169.681 Disconnect switches and devices. (a) Externally operable switches or... protected by fuses, the disconnect switch required for fuses in § 169.683(b) of this chapter is adequate for...

46 CFR 169.681 - Disconnect switches and devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Disconnect switches and devices. 169.681 Section 169.681... Less Than 100 Gross Tons § 169.681 Disconnect switches and devices. (a) Externally operable switches or... protected by fuses, the disconnect switch required for fuses in § 169.683(b) of this chapter is adequate for...

46 CFR 169.681 - Disconnect switches and devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Disconnect switches and devices. 169.681 Section 169.681... Less Than 100 Gross Tons § 169.681 Disconnect switches and devices. (a) Externally operable switches or... protected by fuses, the disconnect switch required for fuses in § 169.683(b) of this chapter is adequate for...

46 CFR 169.681 - Disconnect switches and devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 7 2013-10-01 2013-10-01 false Disconnect switches and devices. 169.681 Section 169.681... Less Than 100 Gross Tons § 169.681 Disconnect switches and devices. (a) Externally operable switches or... protected by fuses, the disconnect switch required for fuses in § 169.683(b) of this chapter is adequate for...

47 CFR 2.1091 - Radiofrequency radiation exposure evaluation: mobile devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of part 1 of this chapter, in particular § 1.1307(b). (b) For purposes of this section, a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained...

47 CFR 2.1091 - Radiofrequency radiation exposure evaluation: mobile devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of part 1 of this chapter, in particular § 1.1307(b). (b) For purposes of this section, a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained...

46 CFR 111.60-1 - Construction and testing of cable.

Code of Federal Regulations, 2010 CFR

2010-10-01

... identification of either IEEE 1580, UL 1309, IEC 92-353, or NPFC MIL-C-24640A or NPFC MIL-C-24643A (all five... 110.10-1). (c) Medium-voltage electric cable must meet the requirements of IEEE 1580 and UL 1072... 1309, IEEE 1580, or section 8 of IEEE 45-2002 (incorporated by reference; see 46 CFR 110.10-1). (e...

Interest of the attenuation coefficient in multiparametric high frequency ultrasound investigation of whole blood coagulation process.

PubMed

Callé, Rachel; Plag, Camille; Patat, Frédéric; Ossant, Frédéric

2009-01-01

Previous studies [R. Libgot, F. Ossant, Y. Gruel, P. Lermusiaux, and F. Patat, Proc.-IEEE Utrason. Symp. 4, 2259-2262 (2005); R. Libgot-Calle, F. Ossant, Y. Gruel, P. Lermusiaux, and F. Patat, Ultrasound Med. Biol. 34, 252-264 (2008); F. Ossant, R. Libgot, P. Coupe, P. Lermusiaux, and F. Patat, Proc.-IEEE Ultrason. Symp. 2, 846-849 (2004)] showed the potential of an in vitro high frequency ultrasound (beyond 20 MHz) device to describe the blood clotting process. The parameters were simultaneously estimated in double transmission (DT) with the calculation of the velocity of longitudinal waves and in backscattering (BS) modes with the estimation of the integrated BS coefficient and the effective scatterer size. The aim of the present study was to show how the integrated attenuation coefficient (IAC) assessed in DT mode could provide additional information on this process, especially regarding the fibrin polymerization which is an important part of the coagulation process. A characteristic time t(a) of the variations in IAC that could be linked to fibrin formation was identified.

Low dimensional carbon electronics

NASA Astrophysics Data System (ADS)

Herring, Patrick Kenichi

This thesis covers several different experiments that comprised my graduate career. The main focus of these experiments was the use of carbon as an electronic material and a steady evolution of fabrication recipes that allowed us to perform reliable and consistent measurements. The second chapter describes experiments with carbon nanotubes, where our goal was to produce devices capable of manipulating electronic spin states in order create quantum bits or "qubits." The third chapter covers the development of fabrication recipes with the goal of creating qubits within Si-Ge nanowire, and the bottom-gating approach that was developed. The fourth chapter begins graphene related research, describing one of the simplest uses of graphene as a simple transparent electrode on a SiN micromembrane. The remainder of the thesis describes experiments that develop graphene based optical and infrared detectors, study their characteristics and determine the physics that underlies their detection mechanism. Key in these experiments were the fabrication recipes that had been developed to create carbon nanotube and Si-Ge nanowire devices. Finally, we demonstrate how engineering of the device's thermal characteristics can lead to improved sensitivity and how graphene can be used in novel applications where conventional materials are not suitable.

Graphene and carbon nanotubes: synthesis, characterization and applications for beyond silicon electronics

NASA Astrophysics Data System (ADS)

Gomez de Arco, Lewis Mortimer

Graphene and carbon nanotubes have outstanding electrical and thermal conductivity. These characteristics make them exciting materials with high potential to replace silicon and surpass its performance in the next generation of semiconductors devices, such devices ought to be considerably smaller and faster than the ones used in present technology. Despite of the excellent electrical and thermal conduction properties of graphene and carbon nanotubes, the advance of nanoelectronics based on them has been hampered due to fundamental limitations of the current synthesis and integration technologies of these carbon nanomaterials. Therefore, there is a strong need to do research at fundamental and applicative levels to help find the roadmap that these materials need to follow, in order to become a real alternative for silicon in future technologies. This dissertation present our approach to overcome some of the most critical problems that hinder the implementation of graphene and carbon nanotubes as important components in real-life macro and nanoelectronic devices. Towards this end, we systematically studied synthesis methods for scalable, high quality graphene and evaluated our large-scale synthesized graphene as transparent electrodes in functional energy conversion devices. In addition, we explored scalable methods to obtain carbon nanotube field-effect transistors with only semiconductor nanotube channels and studied the substrate influence on the structure and metal to semiconductor ratio of aligned nanotubes. Although we have successfully tackled some of the most important challenges of the above-mentioned one- and two-dimensional carbon nanostructures, more remains to be done to integrate them as functional components in electronic devices to reach the goal of transferring them from the laboratory to the manufacturing industry, and ultimately to the society. In chapter 1, a general introduction to carbon nanomaterials is presented, followed by a more focused discussion on the structure and properties of graphene and carbon nanotubes. Chapter 2, presents the development of a chemical vapor deposition method for scalable graphene synthesis and the evaluation of its electrical properties as the active channel in field effect transistor and as a transparent conductor. Chapter 3 presents further work on graphene synthesis on single crystal nickel and the influence of the substrate atomic arrangement on the synthesized graphene. Chapter 4 presents the implementation of the highly scalable graphene synthesized by CVD as the transparent electrode in flexible organic photovoltaic cells. Chapter 5 evaluates the influence of substrate/nanotube interactions during align nanotube growth on the Raman signature of the resulting aligned nanotubes, nanotube structure and metal to semiconductor ratio. Chapter 6 presents our findings on a scalable method that can be used at wafer scale to achieve metal to semiconductor conversion of carbon nanotubes by light irradiation and its application to achieve semiconducting CNTFETs. Finally, in chapter 7, future research directions in related areas of science and technology are proposed.

Charged Slurry Droplet Research

DTIC Science & Technology

1989-02-20

IEEE/IAS annual meeting, Denver, CO, Sept. 28 - Oct. 3, 1986, p.1434. Accepted for publication IEEE Transactions on Industry Applications. 6. Lord...34Analysis of the Description of Evaporating Charged Droplets, IEEE Transactions on Industry Applications, IA-19, 771, 1983. 9. H.M.A. Elghazaly, G.S.P. Castle...34Analysis of the Instability of Evaporating Charged Liquid Drops", IEEE Transactions on Industry Applications, IA-22, 892, 1986. 10. H.M.A

SAR Product Improvements and Enhancements - SARprises

DTIC Science & Technology

2013-09-30

paper on current fields at Orkney, Scotland, was accepted for publication in IEEE - TGARS and is currently in press (available on IEEE Xplore as Early...Sea surface velocity vector retrieval using dual-beam interferometry: First demonstration, IEEE TGARS, 43, 2494- 2502, 2005. [2] Chapron, B., F...Bight by airborne along-track interferometric SAR, Proc. IGARSS 2002, 1822-1824, IEEE , 2002. [4] Bjerklie, D.M., S.L. Dingman, C.J. Vorosmarty, C.H

Performance Analysis of the IEEE 802.11p Multichannel MAC Protocol in Vehicular Ad Hoc Networks

PubMed Central

2017-01-01

Vehicular Ad Hoc Networks (VANETs) employ multichannel to provide a variety of safety and non-safety applications, based on the IEEE 802.11p and IEEE 1609.4 protocols. The safety applications require timely and reliable transmissions, while the non-safety applications require efficient and high throughput. In the IEEE 1609.4 protocol, operating interval is divided into alternating Control Channel (CCH) interval and Service Channel (SCH) interval with an identical length. During the CCH interval, nodes transmit safety-related messages and control messages, and Enhanced Distributed Channel Access (EDCA) mechanism is employed to allow four Access Categories (ACs) within a station with different priorities according to their criticality for the vehicle’s safety. During the SCH interval, the non-safety massages are transmitted. An analytical model is proposed in this paper to evaluate performance, reliability and efficiency of the IEEE 802.11p and IEEE 1609.4 protocols. The proposed model improves the existing work by taking serval aspects and the character of multichannel switching into design consideration. Extensive performance evaluations based on analysis and simulation help to validate the accuracy of the proposed model and analyze the capabilities and limitations of the IEEE 802.11p and IEEE 1609.4 protocols, and enhancement suggestions are given. PMID:29231882

Performance Analysis of the IEEE 802.11p Multichannel MAC Protocol in Vehicular Ad Hoc Networks.

PubMed

Song, Caixia

2017-12-12

Vehicular Ad Hoc Networks (VANETs) employ multichannel to provide a variety of safety and non-safety applications, based on the IEEE 802.11p and IEEE 1609.4 protocols. The safety applications require timely and reliable transmissions, while the non-safety applications require efficient and high throughput. In the IEEE 1609.4 protocol, operating interval is divided into alternating Control Channel (CCH) interval and Service Channel (SCH) interval with an identical length. During the CCH interval, nodes transmit safety-related messages and control messages, and Enhanced Distributed Channel Access (EDCA) mechanism is employed to allow four Access Categories (ACs) within a station with different priorities according to their criticality for the vehicle's safety. During the SCH interval, the non-safety massages are transmitted. An analytical model is proposed in this paper to evaluate performance, reliability and efficiency of the IEEE 802.11p and IEEE 1609.4 protocols. The proposed model improves the existing work by taking serval aspects and the character of multichannel switching into design consideration. Extensive performance evaluations based on analysis and simulation help to validate the accuracy of the proposed model and analyze the capabilities and limitations of the IEEE 802.11p and IEEE 1609.4 protocols, and enhancement suggestions are given.

Research and Development of Tactile Facsimile Reading Aid for the Blind (The Optacon). Final Report.

ERIC Educational Resources Information Center

Linvill, John G.

Presented is a report on the 5-year project to develop the Optacon, an electronic device which allows the blind individual to read ordinary printed matter directly and independently. Chapter (1) provides and introduction and overview of the Optacon Project. Summarized in Chapter (2) is a chronological account of the Optacon Project which traces…

Recent Advances in Photonic Devices for Optical Computing and the Role of Nonlinear Optics-Part II

NASA Technical Reports Server (NTRS)

Abdeldayem, Hossin; Frazier, Donald O.; Witherow, William K.; Banks, Curtis E.; Paley, Mark S.

2007-01-01

The twentieth century has been the era of semiconductor materials and electronic technology while this millennium is expected to be the age of photonic materials and all-optical technology. Optical technology has led to countless optical devices that have become indispensable in our daily lives in storage area networks, parallel processing, optical switches, all-optical data networks, holographic storage devices, and biometric devices at airports. This chapters intends to bring some awareness to the state-of-the-art of optical technologies, which have potential for optical computing and demonstrate the role of nonlinear optics in many of these components. Our intent, in this Chapter, is to present an overview of the current status of optical computing, and a brief evaluation of the recent advances and performance of the following key components necessary to build an optical computing system: all-optical logic gates, adders, optical processors, optical storage, holographic storage, optical interconnects, spatial light modulators and optical materials.

Integrated Optofluidic Multimaterial Fibers

NASA Astrophysics Data System (ADS)

Stolyarov, Alexander Mark

The creation of integrated microphotonic devices requires a challenging assembly of optically and electrically disparate materials into complex geometries with nanometer-scale precision. These challenges are typically addressed by mature wafer-based fabrication methods, which while versatile, are limited to low-aspect-ratio structures and by the inherent complexity of sequential processing steps. Multimaterial preform-to-fiber drawing methods on the other hand present unique opportunities for realizing optical and optoelectronic devices of extended length. Importantly, these methods allow for monolithic integration of all the constituent device components into complex architectures. My research has focused on addressing the challenges and opportunities associated with microfluidic multimaterial fiber structures and devices. Specifically: (1) A photonic bandgap (PBG) fiber is demonstrated for single mode transmission at 1.55 microm with 4 dB/m losses. This fiber transmits laser pulses with peak powers of 13.5 MW. (Chapter 2) (2) A microfluidic fiber laser, characterized by purely radia l emission is demonstrated. The laser cavity is formed by an axially invariant, 17-period annular PBG structure with a unit cell thickness of 160nm. This laser is distinct from traditional lasers with cylindrically symmetric emission, which rely almost exclusively on whispering gallery modes, characterized by tangential wavevectors. (Chapter 4) (3) An array of independently-controlled liquid-crystal microchannels flanked by viscous conductors is integrated in the fiber cladding and encircles the PBG laser cavity in (2). The interplay between the radially-emitting laser and these liquid-crystal modulators enables controlled directional emission around a full azimuthal angular range. (Chapter 4) (4) The electric potential profile along the length of the electrodes in (3) is characterized and found to depend on frequency. This frequency dependence presents a new means to tune the transversely-directed transmission at a given location along the fiber axis. (Chapter 5) (5) A chemical sensing system is created within a fiber. By integrating a chemiluminescent peroxide-sensing material into the hollow core of a PBG fiber, a limit-of-detection of 300 ppb for peroxide vapors is achieved. (Chapter 3)

Fast and Scalable Fabrication of Microscopic Optical Surfaces and its Application for Optical Interconnect Devices

NASA Astrophysics Data System (ADS)

Summitt, Christopher Ryan

The use of optical interconnects is a promising solution to the increasing demand for high speed mass data transmission used in integrated circuits as well as device to device data transfer applications. For the purpose, low cost polymer waveguides are a popular choice for routing signal between devices due to their compatibility with printed circuit boards. In optical interconnect, coupling from an external light source to such waveguides is a critical step, thus a variety of couplers have been investigated such as grating based couplers [1,2], evanescent couplers [3], and embedded mirrors [4-6]. These couplers are inherently micro-optical components which require fast and scalable fabrication for mass production with optical quality surfaces/structures. Low NA laser direct writing has been used for fast fabrication of structures such as gratings and Fresnel lenses using a linear laser direct writing scheme, though the length scale of such structures are an order of magnitude larger than the spot size of the focused laser of the tool. Nonlinear writing techniques such as with 2-photon absorption offer increased write resolution which makes it possible to fabricate sub-wavelength structures as well as having a flexibility in feature shape. However it does not allow a high speed fabrication and in general are not scalable due to limitations of speed and area induced by the tool's high NA optics. To overcome such limitations primarily imposed by NA, we propose a new micro-optic fabrication process which extends the capabilities of 1D, low NA, and thus fast and scalable, laser direct writing to fabricate a structure having a length scale close to the tool's spot size, for example, a mirror based and 45 degree optical coupler with optical surface quality. The newly developed process allows a high speed fabrication with a write speed of 2600 mm²/min by incorporating a mask based lithography method providing a blank structure which is critical to creating a 45 degree slope to form the coupler surface. In this method, instead of using an entire exposure in a pixelated manner, only a portion of the Gaussian profile is used, allowing a reduced surface roughness and better control of the surface shape than previously possible with this low NA beam. The surface figure of the mirror is well controlled below 0.04 waves in root-mean-square (RMS) at 1.55 mum wavelength, with mirror angle of 45+/-1 degrees. The coupling efficiency is evaluated using a set of polymer waveguides fabricated on the same substrate as the complete proof of concept device. Device insertion loss was measured using a custom built optical test station and a detailed loss analysis was completed to characterize the optical coupling efficiency of the mirror. Surface roughness and angle were also experimentally confirmed. This process opens up a pathway towards large volume fabrication of free-form and high aspect ratio optical components which have not yet pursued, along with well-defined optical structures on a single substrate. In this dissertation, in Chapter 1, we provide an overview of optical surface fabrication in conjunction with current state of the art on fabrication of free form surfaces in macro and microscopic length scale. The need for optical interconnects is introduced and fabrication methods of micro-optical couplers are reviewed in Chapter 2. In Chapter 3, the complete fabrication process of a mirror based coupler is presented including a custom alignment procedure. In Chapter 4, we provide the integration procedure of the optical couplers with waveguides. In Chapter 5, the alignment of two-lithographic methods is discussed. In Chapter 6, we provide the fabrication procedure used for the waveguides. In Chapter 7, the experimental evaluation and testing of the optical coupler is described. We present a custom test station used for angle verification and optical coupler efficiency measurement. In Chapter 8, a detailed loss analysis of the device is presented including suggestions for future reductions in loss. Conclusions and future work considerations are addressed in Chapter 9.

Small Structures and Superlattices for Future High-Speed Devices

DTIC Science & Technology

1986-10-01

1985. I-5oA -undoped) [101 M. Ogawa. K. Olsata. T. Fu-usuka. and N. Kawamura . IEEE M-GoAt 1ND) _ -OSP~m Mricrowave Thie.ory Tech., vol. MTT-24, p. 3013...thicknesses range between (T.E.S.) from GTE. We also wish to thank Masako Okamoto 250 and 600 A. Forward I-V measurements that we have and Professor W. M...orientation mixed in among one of us (T.E.S.) from GTE. We also wish to thank Masako the type-B structure. This possibility is discounted by our Okamoto

Application Note: Power Grid Modeling With Xyce.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sholander, Peter E.

This application note describes how to model steady-state power flows and transient events in electric power grids with the SPICE-compatible Xyce TM Parallel Electronic Simulator developed at Sandia National Labs. This application notes provides a brief tutorial on the basic devices (branches, bus shunts, transformers and generators) found in power grids. The focus is on the features supported and assumptions made by the Xyce models for power grid elements. It then provides a detailed explanation, including working Xyce netlists, for simulating some simple power grid examples such as the IEEE 14-bus test case.

Goddard Conference on Mass Storage Systems and Technologies, volume 2

NASA Technical Reports Server (NTRS)

Kobler, Ben (Editor); Hariharan, P. C. (Editor)

1993-01-01

Papers and viewgraphs from the conference are presented. Discussion topics include the IEEE Mass Storage System Reference Model, data archiving standards, high-performance storage devices, magnetic and magneto-optic storage systems, magnetic and optical recording technologies, high-performance helical scan recording systems, and low end helical scan tape drives. Additional discussion topics addressed the evolution of the identifiable unit for processing (file, granule, data set, or some similar object) as data ingestion rates increase dramatically, and the present state of the art in mass storage technology.

Enhancement-Mode Antimonide Quantum-Well MOSFETs With High Electron Mobility and Gigahertz Small-Signal Switching Performance

DTIC Science & Technology

2011-12-01

grown on GaAs by molecular beam epitaxy and the defect-free active device layers. Fig. 1(c) shows the quantitative mobility spec- trum analysis (QMSA...dielectric deposition. A Pd/Au gate metal was defined using e- beam lithography and 0741-3106/$26.00 © 2011 IEEE Report Documentation Page Form...2010, pp. 6.3.1–6.3.4. [2] N. Kharche, G. Klimeck, D. Kim, J. A. del Alamo, and M. Luisier, “Performance analysis of ultra-scaled InAs HEMTs ,” in IEDM

OR.NET: a service-oriented architecture for safe and dynamic medical device interoperability.

PubMed

Kasparick, Martin; Schmitz, Malte; Andersen, Björn; Rockstroh, Max; Franke, Stefan; Schlichting, Stefan; Golatowski, Frank; Timmermann, Dirk

2018-02-23

Modern surgical departments are characterized by a high degree of automation supporting complex procedures. It recently became apparent that integrated operating rooms can improve the quality of care, simplify clinical workflows, and mitigate equipment-related incidents and human errors. Particularly using computer assistance based on data from integrated surgical devices is a promising opportunity. However, the lack of manufacturer-independent interoperability often prevents the deployment of collaborative assistive systems. The German flagship project OR.NET has therefore developed, implemented, validated, and standardized concepts for open medical device interoperability. This paper describes the universal OR.NET interoperability concept enabling a safe and dynamic manufacturer-independent interconnection of point-of-care (PoC) medical devices in the operating room and the whole clinic. It is based on a protocol specifically addressing the requirements of device-to-device communication, yet also provides solutions for connecting the clinical information technology (IT) infrastructure. We present the concept of a service-oriented medical device architecture (SOMDA) as well as an introduction to the technical specification implementing the SOMDA paradigm, currently being standardized within the IEEE 11073 service-oriented device connectivity (SDC) series. In addition, the Session concept is introduced as a key enabler for safe device interconnection in highly dynamic ensembles of networked medical devices; and finally, some security aspects of a SOMDA are discussed.

21 CFR 880.5630 - Nipple shield.

Code of Federal Regulations, 2011 CFR

2011-04-01

... nipple of a nursing woman. This generic device does not include nursing pads intended solely to protect the clothing of a nursing woman from milk. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 880.5630 - Nipple shield.

Code of Federal Regulations, 2013 CFR

2013-04-01

... nipple of a nursing woman. This generic device does not include nursing pads intended solely to protect the clothing of a nursing woman from milk. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 880.5630 - Nipple shield.

Code of Federal Regulations, 2014 CFR

2014-04-01

... nipple of a nursing woman. This generic device does not include nursing pads intended solely to protect the clothing of a nursing woman from milk. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 880.5630 - Nipple shield.

Code of Federal Regulations, 2010 CFR

2010-04-01

... nipple of a nursing woman. This generic device does not include nursing pads intended solely to protect the clothing of a nursing woman from milk. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 880.5630 - Nipple shield.

Code of Federal Regulations, 2012 CFR

2012-04-01

... nipple of a nursing woman. This generic device does not include nursing pads intended solely to protect the clothing of a nursing woman from milk. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 820.200 - Servicing.

Code of Federal Regulations, 2010 CFR

2010-04-01

... reports with appropriate statistical methodology in accordance with § 820.100. (c) Each manufacturer who... chapter shall automatically consider the report a complaint and shall process it in accordance with the... device serviced; (2) Any device identification(s) and control number(s) used; (3) The date of service; (4...

46 CFR 38.15-15 - Electrical installations-TB/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... this chapter for tank vessels, except as otherwise specified in this part. (b) Spaces containing cargo... devices, except Coast Guard approved intrinsically safe devices, shall be installed in these spaces. Electric motors shall be segregated from these spaces by a gastight bulkhead. Electric lighting of the...

46 CFR 38.15-15 - Electrical installations-TB/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... this chapter for tank vessels, except as otherwise specified in this part. (b) Spaces containing cargo... devices, except Coast Guard approved intrinsically safe devices, shall be installed in these spaces. Electric motors shall be segregated from these spaces by a gastight bulkhead. Electric lighting of the...

46 CFR 38.15-15 - Electrical installations-TB/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... this chapter for tank vessels, except as otherwise specified in this part. (b) Spaces containing cargo... devices, except Coast Guard approved intrinsically safe devices, shall be installed in these spaces. Electric motors shall be segregated from these spaces by a gastight bulkhead. Electric lighting of the...

46 CFR 38.15-15 - Electrical installations-TB/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... this chapter for tank vessels, except as otherwise specified in this part. (b) Spaces containing cargo... devices, except Coast Guard approved intrinsically safe devices, shall be installed in these spaces. Electric motors shall be segregated from these spaces by a gastight bulkhead. Electric lighting of the...

46 CFR 38.15-15 - Electrical installations-TB/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... this chapter for tank vessels, except as otherwise specified in this part. (b) Spaces containing cargo... devices, except Coast Guard approved intrinsically safe devices, shall be installed in these spaces. Electric motors shall be segregated from these spaces by a gastight bulkhead. Electric lighting of the...

47 CFR 15.19 - Labelling requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Labelling requirements. 15.19 Section 15.19 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.19 Labelling requirements. (a) In addition to the requirements in part 2 of this chapter, a device subject to certification...

47 CFR 90.103 - Radiolocation Service.

Code of Federal Regulations, 2012 CFR

2012-10-01

... basis to the Government Radiolocation Service. (13) Operations in this band are limited to survey....403(f), and 90.429 of this part. (23) Devices designed to operate as field disturbance sensors on... part 15 of this chapter. (24) Devices designed to operate as field disturbance sensors on frequencies...

47 CFR 90.103 - Radiolocation Service.

Code of Federal Regulations, 2010 CFR

2010-10-01

... basis to the Government Radiolocation Service. (13) Operations in this band are limited to survey....403(f), and 90.429 of this part. (23) Devices designed to operate as field disturbance sensors on... part 15 of this chapter. (24) Devices designed to operate as field disturbance sensors on frequencies...

Chapter 24: Two- and Three-Dimensional Electronic Modeling of Thin-Film Solar Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kanevce, Ana; Metzger, Wyatt K

2016-07-22

Modeling can provide physical insight to device operation, help distinguish important material properties from unimportant properties, predict trends, and help interpret experimental data. Numerical modeling is also useful to simulate different electro-optical experiments, in the presence of grain boundaries (GBs) and nonplanar junctions and geometries, and to help interpret data obtained in such experiments. This chapter presents methods for effective multidimensional modeling. The first step in creating a computational model is defining and providing discretization of a 2D area or a 3D volume. Two main approaches to the discretization have been used for studying solar cells: equivalent-circuit modeling and solvingmore » semiconductor equations. The chapter gives some examples of problems that were addressed with 2D or 3D modeling and the knowledge that was gained through them. Multidimensional modeling including GBs and other material variations is necessary to explain the device physics and experimental results present in diverse thin-film technologies.« less

Being "Stresslessly Invisible": The Rise and Fall of Videophony in David Foster Wallace's "Infinite Jest"

ERIC Educational Resources Information Center

Ribbat, Christoph

2010-01-01

In a satiric chapter of David Foster Wallace's novel "Infinite Jest," a mock media expert reports how American consumers of the near future recoil from a new communication device known as "videophony" and return to the voice-only telephone of the Bell Era. This article explores the said chapter in the framework of media theories reading the…

Moving Up the CMMI Capability and Maturity Levels Using Simulation

DTIC Science & Technology

2008-01-01

Alternative Process Tools, Including NPV and ROI 6 Figure 3: Top-Level View of the Full Life-Cycle Version of the IEEE 12207 PSIM, Including IV&V Layer 19...Figure 4: Screenshot of the Incremental Version Model 19 Figure 5: IEEE 12207 PSIM Showing the Top-Level Life-Cycle Phases 22 Figure 6: IEEE 12207 ...Software Detailed Design for the IEEE 12207 Life- Cycle Process 24 Figure 8: Incremental Life Cycle PSIM Configured for a Specific Project Using SEPG

Sonobuoy-Based, 3-D Acoustic Characterization of Shallow-Water Environments

DTIC Science & Technology

2015-09-30

10.1109/JOE.2014.2362838, ( IEEE Xplore Early Access, 4 Dec 2014)]. For each type of buoy, the eigenvalues at 50, 75, 125, and 175 Hz were used as input...using sonobuoys,” IEEE J. Ocean. Eng., vol. 40, no. 3, pp. 607-620, Jul. 2015 (DOI: 10.1109/JOE.2014.2362838, ( IEEE Xplore Early Access, 4 Dec 2014...et al, “Modal mapping experiment and geoacoustic inversion using sonobuoys,” IEEE J. Ocean. Eng., vol. 40, no. 3, pp. 607- 620, Jul. 2015 (DOI

Observation of molecular level behavior in molecular electronic junction device

NASA Astrophysics Data System (ADS)

Maitani, Masato

In this dissertation, I utilize AFM based scanning probe measurement and surface enhanced Raman scattering based vibrational spectroscopic analysis to directly characterize topographic, electronic, and chemical properties of molecules confined in the local area of M3 junction to elucidate the molecular level behavior of molecular junction electronic devices. In the introduction, the characterization of molecular electronic devices with different types of metal-molecule-metal (M3) structures based upon self-assembled monolayers (SAMs) is reviewed. A background of the characterization methods I use in this dissertation, conducting probe atomic force microscopy (cp-AFM) and surface enhanced Raman spectroscopy (SERS), is provided in chapter 1. Several attempts are performed to create the ideal top metal contacts on SAMs by metal vapor phase deposition in order to prevent the metal penetration inducing critical defects of the molecular electronic devices. The scanning probe microscopy (SPM), such as cp-AFM, contact mode (c-) AFM and non-contact mode (nc-) AFM, in ultra high vacuum conditions are utilized to study the process of the metal-SAM interface construction in terms of the correlation between the morphological and electrical properties including the metal nucleation and filament generation as a function of the functionalization of long-chain alkane thiolate SAMs on Au. In chapter 2, the nascent condensation process of vapor phase Al deposition on inert and reactive SAMs are studied by SPM. The results of top deposition, penetration, and filament generation of deposited Al are discussed and compared to the results previously observed by spectroscopic measurements. Cp-AFM was shown to provide new insights into Al filament formation which has not been observed by conventional spectroscopic analysis. Additionally, the electronic characteristics of individual Al filaments are measured. Chapter 3 reveals SPM characterization of Au deposition onto --COOH terminated SAMs utilized with strong surface dipole-dipole intermolecular interaction based on hydrogen bonding and ionic bonding potentially preventing the metal penetration. The observed results are discussed with kinetic paths of metal atoms on each SAM including temporal vacancies controlled by the intermolecular interactions in SAM upon the comparison with the spectroscopic results previously reported. The results in chapter 2 and 3 strongly suggests that AFM based characterization technique is powerful tool especially for detecting molecular-size local phenomena in vapor phase metal deposition process, especially, the electric short-circuit filaments growing through SAMs, which may induce critical misinterpretation of M3 junction device properties. In Chapter 4, an altered metal deposition process on inert SAM with using a buffer layer is performed to diminish the kinetic energy of impinging metal atoms. SPM characterization reveals an abrupt metal-SAM interface without any metal penetration. Examined electric characteristics also revealed typical non-resonant tunneling characteristics of long chain alkane thiolate SAMs. In chapter 5, the buffer layer assisted growth process is used to prepare a nano particles-SAM pristine interface on SAMs to control the metal-SAM interaction in order to study the fundamental issue of chemical enhancement mechanism of SERS. Identical Au nanoparticles-SAM-Au M3 structures with different Au-SAM interactions reveal a large discrepancy of enhancement factors of ˜100 attributed to the chemical interaction. In chapter 6, Raman spectroscopy of M3 junction is applied to the characterization of molecular electronics devices. A crossed nanowire junction (X-nWJ) device is employed for in-situ electronic-spectroscopic simultaneous characterization using Raman spectroscopy. A detailed study reveals the multi-probe capability of X-nWJ for in-situ Raman and in-elastic electron tunneling spectroscopy (IETS) as vibrational spectroscopies to diagnose molecular electronic devices. In chapter 7, aniline oligomer (OAn) based redox SAMs are characterized by spectroscopic and microscopic methods under different chemical redox states by reflection absorption infrared spectroscopy (RAIRS), Raman, x-ray photoelectron spectroscopy (XPS), and AFM in order to elucidate the mechanism of electric switching molecular junctions previously reported. Obtained results are discussed in terms of the chemical and geometrical conformations of molecules in closely packed SAM domains. In chapter 8, in-situ Raman spectroscopy and cp-AFM microscopic techniques are applied to study the electric switching characteristics of X-nWJ incorporating OAn based SAM. The results of tunneling current and in-situ Raman spectroscopy are discussed with the conformational change of OAn component. The conductance switching mechanism associated with domain conformation change of OAn SAM is proposed and evaluated based on the results.

47 CFR 15.19 - Labelling requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 1 2011-10-01 2011-10-01 false Labelling requirements. 15.19 Section 15.19 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL RADIO FREQUENCY DEVICES General § 15.19 Labelling requirements. (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be...

21 CFR 886.1200 - Optokinetic drum.

Code of Federal Regulations, 2010 CFR

2010-04-01

... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be... of the eyeball) in patients. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter, subject to the...

21 CFR 886.1200 - Optokinetic drum.

Code of Federal Regulations, 2011 CFR

2011-04-01

... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be... of the eyeball) in patients. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter, subject to the...

21 CFR 886.1200 - Optokinetic drum.

Code of Federal Regulations, 2014 CFR

2014-04-01

... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be... of the eyeball) in patients. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter, subject to the...

21 CFR 886.1200 - Optokinetic drum.

Code of Federal Regulations, 2013 CFR

2013-04-01

... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be... of the eyeball) in patients. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter, subject to the...

21 CFR 886.1200 - Optokinetic drum.

Code of Federal Regulations, 2012 CFR

2012-04-01

... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be... of the eyeball) in patients. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter, subject to the...

Current state of the mass storage system reference model

NASA Technical Reports Server (NTRS)

Coyne, Robert

1993-01-01

IEEE SSSWG was chartered in May 1990 to abstract the hardware and software components of existing and emerging storage systems and to define the software interfaces between these components. The immediate goal is the decomposition of a storage system into interoperable functional modules which vendors can offer as separate commercial products. The ultimate goal is to develop interoperable standards which define the software interfaces, and in the distributed case, the associated protocols to each of the architectural modules in the model. The topics are presented in viewgraph form and include the following: IEEE SSSWG organization; IEEE SSSWG subcommittees & chairs; IEEE standards activity board; layered view of the reference model; layered access to storage services; IEEE SSSWG emphasis; and features for MSSRM version 5.

Performance analysis and simulation of vertical gallium nitride nanowire transistors

NASA Astrophysics Data System (ADS)

Witzigmann, Bernd; Yu, Feng; Frank, Kristian; Strempel, Klaas; Fatahilah, Muhammad Fahlesa; Schumacher, Hans Werner; Wasisto, Hutomo Suryo; Römer, Friedhard; Waag, Andreas

2018-06-01

Gallium nitride (GaN) nanowire transistors are analyzed using hydrodynamic simulation. Both p-body and n-body devices are compared in terms of threshold voltage, saturation behavior and transconductance. The calculations are calibrated using experimental data. The threshold voltage can be tuned from enhancement to depletion mode with wire doping. Surface states cause a shift of threshold voltage and saturation current. The saturation current depends on the gate design, with a composite gate acting as field plate in the p-body device. He joined Bell Laboratories, Murray Hill, NJ, as a Technical Staff Member. In October 2001, he joined the Optical Access and Transport Division, Agere Systems, Alhambra, CA. In 2004, he was appointed an Assistant Professor at ETH Zurich,. Since 2008, at the University of Kassel, Kassel, Germany, and he has been a Professor the Head of the Computational Electronics and Photonics Group, and co-director of CINSaT since 2010. His research interests include computational optoelectronics, process and device design of semiconductor photonic devices, microwave components, and electromagnetics modeling for nanophotonics. Dr. Witzigmann is a senior member of the SPIE and IEEE.

A selection of biomechanical research problems: From modeling to experimentation

NASA Astrophysics Data System (ADS)

Abbasi, Cyrus Omid

The research undertakings within this manuscript illustrate the importance of biomechanics in today's science. Without doubt, biomechanics can be utilized to obtain a better understanding of many unsolved mysteries involved in the field of medicine. Moreover, biomechanics can be used to develop better prosthetic or surgical devices as well. Chapter 2 represents a medical problem, which has not been solved for more than a century. With the use of fundamental principles of biomechanics', a better insight of this problem and its possible causes were obtained. Chapter 3 investigates the mechanical interaction between the human teeth and some processed food products during mastication, which is a routine but crucial daily activity of a human being. Chapter 4 looks at a problem within the field of surgery. In this chapter the stability and reliability of two different Suturing-Techniques are explored. Chapters 5 and 6 represent new patent designs as a result of the investigations made in Chapter 4. Chapter 7 studies the impact and load transfer patterns during the collision between a child's head and the ground. All of the above mentioned chapters show the significance of biomechanics in solving a range of different medical problems that involve physical and or mechanical characters.

Industry careers for the biomedical engineer.

PubMed

Munzner, Robert F

2004-01-01

This year's conference theme is "linkages for innovation in biomedicine." Biomedical engineers, especially those transitioning their career from academic study into medical device industry, will play a critical role in converting the fruits of scientific research into the reality of modern medical devices. This special session is organized to help biomedical engineers to achieve their career goals more effectively. Participants will have opportunities to hear from and interact with leading industrial experts on many issues. These may include but not limited to 1) career paths for biomedical engineers (industrial, academic, or federal; technical vs. managerial track; small start-up or large established companies); 2) unique design challenges and regulatory requirements in medical device development; 3) aspects of a successful biomedical engineering job candidate (such as resume, interview, follow-up). Suggestions for other topics are welcome and should be directed to xkong@ieee.org The distinguished panelists include: Xuan Kong, Ph.D., VP of Research, NEUROMetrix Inc, Waltham, MA Robert F. Munzner, Ph.D., Medical Device Consultant, Doctor Device, Herndon, VA Glen McLaughlin, Ph.D., VP of Engineering and CTO, Zonare Medical System Inc., Mountain View, CA Grace Bartoo, Ph.D., RAC, General Manager, Decus Biomedical LLC San Carlos, CA.

Design and Implementation of an Innovative Residential PV System

NASA Astrophysics Data System (ADS)

Najm, Elie Michel

This work focuses on the design and implementation of an innovative residential PV system. In chapter one, after an introduction related to the rapid growth of solar systems' installations, the most commonly used state of the art solar power electronics' configurations are discussed, which leads to introducing the proposed DC/DC parallel configuration. The advantages and disadvantages of each of the power electronics' configurations are deliberated. The scope of work in the power electronics is defined in this chapter to be related to the panel side DC/DC converter. System integration and mechanical proposals are also within the scope of work and are discussed in later chapters. Operation principle of a novel low cost PV converter is proposed in chapter 2. The proposal is based on an innovative, simplified analog implementation of a master/slave methodology resulting in an efficient, soft-switched interleaved variable frequency flybacks, operating in the boundary conduction mode (BCM). The scheme concept and circuit configuration, operation principle and theoretical waveforms, design equations, and design considerations are presented. Furthermore, design examples are also given, illustrating the significance of the newly derived frequency equation for flybacks operating in BCM. In chapters 3, 4, and 5, the design implementation and optimization of the novel DC/DC converter illustrated in chapter 2 are discussed. In chapter 3, a detailed variable frequency BCM flyback design model leading to optimizing the component selections and transformer design, detailed in chapter 4, is presented. Furthermore, in chapter 4, the method enabling the use of lower voltage rating switching devices is also discussed. In chapter 5, circuitry related to Start-UP, drive for the main switching devices, zero-voltage-switching (ZVS) as well as turn OFF soft switching and interleaving control are fully detailed. The experimental results of the proposed DC/DC converter are presented in chapter 6. In chapter 7, a novel integration method is proposed for the residential PV solar system. The proposal presents solutions to challenges experimented in the implementation of today's approaches. Faster installation time, easier system grounding, and integration of the power electronics in order to reduce the number of connectors' and system cost are detailed. Installers with special skills as well as special tools are not required for implementing the proposed system integration. Photos of the experimental results related to the installation of a 3kW system, which was fully completed in less than an hour and a half, are also presented.

Current state of micro-robots/devices as substitutes for screening colonoscopy: assessment based on technology readiness levels.

PubMed

Tapia-Siles, Silvia C; Coleman, Stuart; Cuschieri, Alfred

2016-02-01

Previous reports have described several candidates, which have the potential to replace colonoscopy, but to date, there is still no device capable of fully replacing flexible colonoscopy in the management of colonic disorders and for mass adult population screening for asymptomatic colorectal cancer. NASA developed the TRL methodology to describe and define the stages of development before use and marketing of any device. The definitions of the TRLS used in the present review are those formulated by "The US Department of Defense Technology Readiness Assessment Guidance" but adapted to micro-robots for colonoscopy. All the devices included are reported in scientific literature. They were identified by a systematic search in Web of Science, PubMed and IEEE Xplore amongst other sources. Devices that clearly lack the potential for full replacement of flexible colonoscopy were excluded. The technological salient features of all the devices included for assessment are described briefly, with particular focus on device propulsion. The devices are classified according to the TRL criteria based on the reported information. An analysis is next undertaken of the characteristics and salient features of the devices included in the review: wireless/tethered devices, data storage-transmission and navigation, additional functionality, residual technology challenges and clinical and socio-economical needs. Few devices currently possess the required functionality and performance to replace the conventional colonoscopy. The requirements, including functionalities which favour the development of a micro-robot platform to replace colonoscopy, are highlighted.

Multifunctional organic thin films and their electronic/optical properties

NASA Astrophysics Data System (ADS)

Shao, Yan

The concept of multifunctional organic thin films and their electronic/optical properties has been applied to organic functional device design, fabrication, and characterization. The organic devices involve organic light-emitting diodes (OLEDs) and organic photovoltaic devices (OPV) in this dissertation. In the research of graded junction structure of OLEDs, two kinds of naturally-formed graded junction (NFGJ) structures, sharp and shallow graded junctions, can be formed using single thermal evaporation boat loaded with uniformly mixed charge transport and light-emitting materials. OLEDs with NFGJ have been demonstrated in Chapter 3; the performance is comparable to the heterojunction OLEDs, but with better device lifetime. A novel method to prepare highly uniform mixed organic solid solutions through a high temperature and high-pressure fusion process has been demonstrated in Chapter 4. A series of fused organic solid solution (FOSS) compounds with NPD doped with different organic emitting dopants were prepared and DSC technique was utilized to determine the thermal characteristics. For the first time, the schematic phase diagram for this binary system has been obtained. High performance OLEDs of single color and white emission were fabricated and the device properties were characterized. In Chapter 5, an efficient photovoltaic heterojunction of tetracene and fullerene has been investigated and high performance organic solar cells have been demonstrated by thermal deposition and successive heat treatment. The preliminary conclusion for this enhancement is discussed and supported by atomic force microscopy images, absorption spectra and x-ray diffraction analysis. Additionally, an effective organic photovoltaic heterojunction based on the typical triplet material PtOEP was demonstrated. It is believed that introducing appropriate organic materials with long exciton lifetime is a very promising way to improve photovoltaic performance.

Augmented reality for the surgeon: Systematic review.

PubMed

Yoon, Jang W; Chen, Robert E; Kim, Esther J; Akinduro, Oluwaseun O; Kerezoudis, Panagiotis; Han, Phillip K; Si, Phong; Freeman, William D; Diaz, Roberto J; Komotar, Ricardo J; Pirris, Stephen M; Brown, Benjamin L; Bydon, Mohamad; Wang, Michael Y; Wharen, Robert E; Quinones-Hinojosa, Alfredo

2018-04-30

Since the introduction of wearable head-up displays, there has been much interest in the surgical community adapting this technology into routine surgical practice. We used the keywords augmented reality OR wearable device OR head-up display AND surgery using PubMed, EBSCO, IEEE and SCOPUS databases. After exclusions, 74 published articles that evaluated the utility of wearable head-up displays in surgical settings were included in our review. Across all studies, the most common use of head-up displays was in cases of live streaming from surgical microscopes, navigation, monitoring of vital signs, and display of preoperative images. The most commonly used head-up display was Google Glass. Head-up displays enhanced surgeons' operating experience; common disadvantages include limited battery life, display size and discomfort. Due to ergonomic issues with dual-screen devices, augmented reality devices with the capacity to overlay images onto the surgical field will be key features of next-generation surgical head-up displays. Copyright © 2018 John Wiley & Sons, Ltd.

David Mooney | NREL

Science.gov Websites

: Institute of Electrical and Electronics Engineers (IEEE). NREL/CP-5500-54165. doi:10.1109/EnergyTech 2011. Piscataway, NJ: Institute of Electrical and Electronics Engineers (IEEE). NREL/CP-5500-53565. doi Electrical and Electronics Engineers (IEEE). NREL/CP-550-47061. doi:10.1109/pes.2009.5275358 Mooney, D., M

Appendix C: Automated Vitrification of Mammalian Embryos on a Digital Microfluidic Device.

PubMed

Liu, Jun; Pyne, Derek G; Abdelgawad, Mohamed; Sun, Yu

2017-01-01

This chapter introduces a digital microfluidic device that automates sample preparation for mammalian embryo vitrification. Individual microdroplets manipulated on the microfluidic device were used as microvessels to transport a single mouse embryo through a complete vitrification procedure. Advantages of this approach, compared to manual operation and channel-based microfluidic vitrification, include automated operation, cryoprotectant concentration gradient generation, and feasibility of loading and retrieval of embryos.

14 CFR 61.163 - Aeronautical experience: Powered-lift category rating.

Code of Federal Regulations, 2013 CFR

2013-01-01

... time in a flight simulator or flight training device. (ii) A maximum of 50 hours of training in a flight simulator or flight training device may be credited toward the instrument flight time requirements... training center certificated under part 142 of this chapter. (iii) Training in a flight simulator or flight...

14 CFR 61.163 - Aeronautical experience: Powered-lift category rating.

Code of Federal Regulations, 2014 CFR

2014-01-01

... time in a flight simulator or flight training device. (ii) A maximum of 50 hours of training in a flight simulator or flight training device may be credited toward the instrument flight time requirements... training center certificated under part 142 of this chapter. (iii) Training in a flight simulator or flight...

14 CFR 61.163 - Aeronautical experience: Powered-lift category rating.

Code of Federal Regulations, 2012 CFR

2012-01-01

... time in a flight simulator or flight training device. (ii) A maximum of 50 hours of training in a flight simulator or flight training device may be credited toward the instrument flight time requirements... training center certificated under part 142 of this chapter. (iii) Training in a flight simulator or flight...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2010 CFR

2010-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2014 CFR

2014-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2012 CFR

2012-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2011 CFR

2011-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

21 CFR 864.6700 - Erythrocyte sedimentation rate test.

Code of Federal Regulations, 2013 CFR

2013-04-01

... sedimentation rate test. (a) Identification. An erythrocyte sedimentation rate test is a device that measures the length of time required for the red cells in a blood sample to fall a specified distance or a... device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter...

Cellular effects of acute exposure to high peak power microwave systems: Morphology and toxicology.

PubMed

Ibey, Bennett L; Roth, Caleb C; Ledwig, Patrick B; Payne, Jason A; Amato, Alayna L; Dalzell, Danielle R; Bernhard, Joshua A; Doroski, Michael W; Mylacraine, Kevin S; Seaman, Ronald L; Nelson, Gregory S; Woods, Clifford W

2016-03-15

Electric fields produced by advanced pulsed microwave transmitter technology now readily exceed the Institute of Electrical and Electronic Engineers (IEEE) C.95.1 peak E-field limit of 100 kV/m, highlighting a need for scientific validation of such a specific limit. Toward this goal, we exposed Jurkat Clone E-6 human lymphocyte preparations to 20 high peak power microwave (HPPM) pulses (120 ns duration) with a mean peak amplitude of 2.3 MV/m and standard deviation of 0.1 with the electric field at cells predicted to range from 0.46 to 2.7 MV/m, well in excess of current standard limit. We observed that membrane integrity and cell morphology remained unchanged 4 h after exposure and cell survival 24 h after exposure was not statistically different from sham exposure or control samples. Using flow cytometry to analyze membrane disruption and morphological changes per exposed cell, no changes were observed in HPPM-exposed samples. Current IEEE C95.1-2005 standards for pulsed radiofrequency exposure limits peak electric field to 100 kV/m for pulses shorter than 100 ms [IEEE (1995) PC95.1-Standard for Safety Levels with Respect to Human Exposure to Electric, Magnetic and Electromagnetic Fields, 0 Hz to 300 GHz, Institute of Electrical and Electronic Engineers: Piscataway, NJ, USA]. This may impose large exclusion zones that limit HPPM technology use. In this study, we offer evidence that maximum permissible exposure of 100 kV/m for peak electric field may be unnecessarily restrictive for HPPM devices. Bioelectromagnetics. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

IEEE 802.15.4 Frame Aggregation Enhancement to Provide High Performance in Life-Critical Patient Monitoring Systems

PubMed Central

Akbar, Muhammad Sajjad; Yu, Hongnian; Cang, Shuang

2017-01-01

In wireless body area sensor networks (WBASNs), Quality of Service (QoS) provision for patient monitoring systems in terms of time-critical deadlines, high throughput and energy efficiency is a challenging task. The periodic data from these systems generates a large number of small packets in a short time period which needs an efficient channel access mechanism. The IEEE 802.15.4 standard is recommended for low power devices and widely used for many wireless sensor networks applications. It provides a hybrid channel access mechanism at the Media Access Control (MAC) layer which plays a key role in overall successful transmission in WBASNs. There are many WBASN’s MAC protocols that use this hybrid channel access mechanism in variety of sensor applications. However, these protocols are less efficient for patient monitoring systems where life critical data requires limited delay, high throughput and energy efficient communication simultaneously. To address these issues, this paper proposes a frame aggregation scheme by using the aggregated-MAC protocol data unit (A-MPDU) which works with the IEEE 802.15.4 MAC layer. To implement the scheme accurately, we develop a traffic patterns analysis mechanism to understand the requirements of the sensor nodes in patient monitoring systems, then model the channel access to find the performance gap on the basis of obtained requirements, finally propose the design based on the needs of patient monitoring systems. The mechanism is initially verified using numerical modelling and then simulation is conducted using NS2.29, Castalia 3.2 and OMNeT++. The proposed scheme provides the optimal performance considering the required QoS. PMID:28134853

IEEE 802.15.4 Frame Aggregation Enhancement to Provide High Performance in Life-Critical Patient Monitoring Systems.

PubMed

Akbar, Muhammad Sajjad; Yu, Hongnian; Cang, Shuang

2017-01-28

In wireless body area sensor networks (WBASNs), Quality of Service (QoS) provision for patient monitoring systems in terms of time-critical deadlines, high throughput and energy efficiency is a challenging task. The periodic data from these systems generates a large number of small packets in a short time period which needs an efficient channel access mechanism. The IEEE 802.15.4 standard is recommended for low power devices and widely used for many wireless sensor networks applications. It provides a hybrid channel access mechanism at the Media Access Control (MAC) layer which plays a key role in overall successful transmission in WBASNs. There are many WBASN's MAC protocols that use this hybrid channel access mechanism in variety of sensor applications. However, these protocols are less efficient for patient monitoring systems where life critical data requires limited delay, high throughput and energy efficient communication simultaneously. To address these issues, this paper proposes a frame aggregation scheme by using the aggregated-MAC protocol data unit (A-MPDU) which works with the IEEE 802.15.4 MAC layer. To implement the scheme accurately, we develop a traffic patterns analysis mechanism to understand the requirements of the sensor nodes in patient monitoring systems, then model the channel access to find the performance gap on the basis of obtained requirements, finally propose the design based on the needs of patient monitoring systems. The mechanism is initially verified using numerical modelling and then simulation is conducted using NS2.29, Castalia 3.2 and OMNeT++. The proposed scheme provides the optimal performance considering the required QoS.

Optical calibration of a new two-way optical component network analyzer

NASA Astrophysics Data System (ADS)

Tsao, Shyh-Lin; Ko, Chih-Han; Liou, Tai-Chi

2003-12-01

High-speed fiber communications show promising results recently [1,2]. Using of lightwave technology for measuring S parameters with optical component becoming important. For this purpose to develop a two-way network analyzer has been reported [3]. In this paper, we report the calibration method of a new two-way lightwave component analyze for applying in fiber optical signal processing elements. The background error and circulator wavelength response are all calibrated. We have designed a new probe for two-way optical component network analyzer. The probe is composed of frequency division multiplexer(FDM), electrical circulator, optical transmitter, optical receiver, and an optical circulator. We design 2-D grating structures as frequency division. The PCB we adopted is Kinstan GD1530 160 whose relative dielectric constantɛ= 4.3, length= 120 mm, and height= 1.8 mm. Two dimensional non-metal covered array square pads are designed on FR4 Glass-Epoxy board for FDM. The FDM can be achieved by the two dimensional non-metalized covered array square pads. Finally we use a single fiber ring resonator filter as our test samples. Comparing the numerical and experimental results, test the device we made. References [1] D. D. Curtis and E. E. Ames,"Optical Test Set for Microwave Fiber-Optic Network Analysis," IEEE Transactions on Microwave Theory and Techniques. , vol. 38, NO.5, pp. 552-559, 1990. [2] J. A. C. Bingham,"Multicarrier modulation for data transmission: an idea whose time has come," IEEE Commun. Magazine., pp. 5 -14, 1990. [3] M. Nakazawa, K. Suzuki, and Y. Kimura, " 3.2-5 Gbps 100km error-free soliton transmission with erbium amplifiers and repenters," IEEE Photonics Tech Lett.,vol.2,pp.216-219,1990.

Anomaly Detection Using Optimally-Placed μPMU Sensors in Distribution Grids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jamei, Mahdi; Scaglione, Anna; Roberts, Ciaran

IEEE As the distribution grid moves toward a tightly-monitored network, it is important to automate the analysis of the enormous amount of data produced by the sensors to increase the operators situational awareness about the system. Here, focusing on Micro-Phasor Measurement Unit (μPMU) data, we propose a hierarchical architecture for monitoring the grid and establish a set of analytics and sensor fusion primitives for the detection of abnormal behavior in the control perimeter. And due to the key role of the μPMU devices in our architecture, a source-constrained optimal μPMU placement is also described that finds the best location ofmore » the devices with respect to our rules. The effectiveness of the proposed methods are tested through the synthetic and real μPMU data.« less

Extraction of the gate capacitance coupling coefficient in floating gate non-volatile memories: Statistical study of the effect of mismatching between floating gate memory and reference transistor in dummy cell extraction methods

NASA Astrophysics Data System (ADS)

Rafhay, Quentin; Beug, M. Florian; Duane, Russell

2007-04-01

This paper presents an experimental comparison of dummy cell extraction methods of the gate capacitance coupling coefficient for floating gate non-volatile memory structures from different geometries and technologies. These results show the significant influence of mismatching floating gate devices and reference transistors on the extraction of the gate capacitance coupling coefficient. In addition, it demonstrates the accuracy of the new bulk bias dummy cell extraction method and the importance of the β function, introduced recently in [Duane R, Beug F, Mathewson A. Novel capacitance coupling coefficient measurement methodology for floating gate non-volatile memory devices. IEEE Electr Dev Lett 2005;26(7):507-9], to determine matching pairs of floating gate memory and reference transistor.

Anomaly Detection Using Optimally-Placed μPMU Sensors in Distribution Grids

DOE PAGES

Jamei, Mahdi; Scaglione, Anna; Roberts, Ciaran; ...

2017-10-25

IEEE As the distribution grid moves toward a tightly-monitored network, it is important to automate the analysis of the enormous amount of data produced by the sensors to increase the operators situational awareness about the system. Here, focusing on Micro-Phasor Measurement Unit (μPMU) data, we propose a hierarchical architecture for monitoring the grid and establish a set of analytics and sensor fusion primitives for the detection of abnormal behavior in the control perimeter. And due to the key role of the μPMU devices in our architecture, a source-constrained optimal μPMU placement is also described that finds the best location ofmore » the devices with respect to our rules. The effectiveness of the proposed methods are tested through the synthetic and real μPMU data.« less

On the Feasibility of Wireless Multimedia Sensor Networks over IEEE 802.15.5 Mesh Topologies

PubMed Central

Garcia-Sanchez, Antonio-Javier; Losilla, Fernando; Rodenas-Herraiz, David; Cruz-Martinez, Felipe; Garcia-Sanchez, Felipe

2016-01-01

Wireless Multimedia Sensor Networks (WMSNs) are a special type of Wireless Sensor Network (WSN) where large amounts of multimedia data are transmitted over networks composed of low power devices. Hierarchical routing protocols typically used in WSNs for multi-path communication tend to overload nodes located within radio communication range of the data collection unit or data sink. The battery life of these nodes is therefore reduced considerably, requiring frequent battery replacement work to extend the operational life of the WSN system. In a wireless sensor network with mesh topology, any node may act as a forwarder node, thereby enabling multiple routing paths toward any other node or collection unit. In addition, mesh topologies have proven advantages, such as data transmission reliability, network robustness against node failures, and potential reduction in energy consumption. This work studies the feasibility of implementing WMSNs in mesh topologies and their limitations by means of exhaustive computer simulation experiments. To this end, a module developed for the Synchronous Energy Saving (SES) mode of the IEEE 802.15.5 mesh standard has been integrated with multimedia tools to thoroughly test video sequences encoded using H.264 in mesh networks. PMID:27164106

On the Feasibility of Wireless Multimedia Sensor Networks over IEEE 802.15.5 Mesh Topologies.

PubMed

Garcia-Sanchez, Antonio-Javier; Losilla, Fernando; Rodenas-Herraiz, David; Cruz-Martinez, Felipe; Garcia-Sanchez, Felipe

2016-05-05

Wireless Multimedia Sensor Networks (WMSNs) are a special type of Wireless Sensor Network (WSN) where large amounts of multimedia data are transmitted over networks composed of low power devices. Hierarchical routing protocols typically used in WSNs for multi-path communication tend to overload nodes located within radio communication range of the data collection unit or data sink. The battery life of these nodes is therefore reduced considerably, requiring frequent battery replacement work to extend the operational life of the WSN system. In a wireless sensor network with mesh topology, any node may act as a forwarder node, thereby enabling multiple routing paths toward any other node or collection unit. In addition, mesh topologies have proven advantages, such as data transmission reliability, network robustness against node failures, and potential reduction in energy consumption. This work studies the feasibility of implementing WMSNs in mesh topologies and their limitations by means of exhaustive computer simulation experiments. To this end, a module developed for the Synchronous Energy Saving (SES) mode of the IEEE 802.15.5 mesh standard has been integrated with multimedia tools to thoroughly test video sequences encoded using H.264 in mesh networks.

Distributed Continuous Event-Based Data Acquisition Using the IEEE 1588 Synchronization and FlexRIO FPGA

NASA Astrophysics Data System (ADS)

Taliercio, C.; Luchetta, A.; Manduchi, G.; Rigoni, A.

2017-07-01

High-speed event driven acquisition is normally performed by analog-to-digital converter (ADC) boards with a given number of pretrigger sample and posttrigger sample that are recorded upon the occurrence of a hardware trigger. A direct physical connection is, therefore, required between the source of event (trigger) and the ADC, because any other software-based communication method would introduce a delay in triggering that would turn out to be not acceptable in many cases. This paper proposes a solution for the relaxation of the event communication time that can be, in this case, carried out by software messaging (e.g., via an LAN), provided that the system components are synchronized in time using the IEEE 1588 synchronization mechanism. The information about the exact event occurrence time is contained in the software packet that is sent to communicate the event and is used by the ADC FPGA to identify the exact sample in the ADC sample queue. The length of the ADC sample queue will depend on the maximum delay in software event message communication time. A prototype implementation using a National FlexRIO FPGA board connected with an ADC device is presented as the proof of concept.

Connecting the clinical IT infrastructure to a service-oriented architecture of medical devices.

PubMed

Andersen, Björn; Kasparick, Martin; Ulrich, Hannes; Franke, Stefan; Schlamelcher, Jan; Rockstroh, Max; Ingenerf, Josef

2018-02-23

The new medical device communication protocol known as IEEE 11073 SDC is well-suited for the integration of (surgical) point-of-care devices, so are the established Health Level Seven (HL7) V2 and Digital Imaging and Communications in Medicine (DICOM) standards for the communication of systems in the clinical IT infrastructure (CITI). An integrated operating room (OR) and other integrated clinical environments, however, need interoperability between both domains to fully unfold their potential for improving the quality of care as well as clinical workflows. This work thus presents concepts for the propagation of clinical and administrative data to medical devices, physiologic measurements and device parameters to clinical IT systems, as well as image and multimedia content in both directions. Prototypical implementations of the derived components have proven to integrate well with systems of networked medical devices and with the CITI, effectively connecting these heterogeneous domains. Our qualitative evaluation indicates that the interoperability concepts are suitable to be integrated into clinical workflows and are expected to benefit patients and clinicians alike. The upcoming HL7 Fast Healthcare Interoperability Resources (FHIR) communication standard will likely change the domain of clinical IT significantly. A straightforward mapping to its resource model thus ensures the tenability of these concepts despite a foreseeable change in demand and requirements.

A micromachined thermally compensated thin film Lamb wave resonator for frequency control and sensing applications

NASA Astrophysics Data System (ADS)

Wingqvist, G.; Arapan, L.; Yantchev, V.; Katardjiev, I.

2009-03-01

Micromachined thin film plate acoustic wave resonators (FPARs) utilizing the lowest order symmetric Lamb wave (S0) propagating in highly textured 2 µm thick aluminium nitride (AlN) membranes have been successfully demonstrated (Yantchev and Katardjiev 2007 IEEE Trans. Ultrason. Ferroelectr. Freq. Control 54 87-95). The proposed devices have a SAW-based design and exhibit Q factors of up to 3000 at a frequency around 900 MHz as well as design flexibility with respect to the required motional resistance. However, a notable drawback of the proposed devices is the non-zero temperature coefficient of frequency (TCF) which lies in the range -20 ppm K-1 to -25 ppm K-1. Thus, despite the promising features demonstrated, further device optimization is required. In this work temperature compensation of thin AlN film Lamb wave resonators is studied and experimentally demonstrated. Temperature compensation while retaining at the same time the device electromechanical coupling is experimentally demonstrated. The zero TCF Lamb wave resonators are fabricated onto composite AlN/SiO2 membranes. Q factors of around 1400 have been measured at a frequency of around 755 MHz. Finally, the impact of technological issues on the device performance is discussed in view of improving the device performance.

IEEE International Symposium on Biomedical Imaging.

PubMed

2017-01-01

The IEEE International Symposium on Biomedical Imaging (ISBI) is a scientific conference dedicated to mathematical, algorithmic, and computational aspects of biological and biomedical imaging, across all scales of observation. It fosters knowledge transfer among different imaging communities and contributes to an integrative approach to biomedical imaging. ISBI is a joint initiative from the IEEE Signal Processing Society (SPS) and the IEEE Engineering in Medicine and Biology Society (EMBS). The 2018 meeting will include tutorials, and a scientific program composed of plenary talks, invited special sessions, challenges, as well as oral and poster presentations of peer-reviewed papers. High-quality papers are requested containing original contributions to the topics of interest including image formation and reconstruction, computational and statistical image processing and analysis, dynamic imaging, visualization, image quality assessment, and physical, biological, and statistical modeling. Accepted 4-page regular papers will be published in the symposium proceedings published by IEEE and included in IEEE Xplore. To encourage attendance by a broader audience of imaging scientists and offer additional presentation opportunities, ISBI 2018 will continue to have a second track featuring posters selected from 1-page abstract submissions without subsequent archival publication.

Exhaust Gas Energy Recovery Technology Applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wagner, Robert M; Szybist, James P

2014-01-01

Exhaust waste heat recovery systems have the potential to significantly improve vehicle fuel economy for conventional and hybrid electric powertrains spanning passenger to heavy truck applications. This chapter discusses thermodynamic considerations and three classes of energy recovery technologies which are under development for vehicle applications. More specifically, this chapter describes the state-of-the-art in exhaust WHR as well as challenges and opportunities for thermodynamic power cycles, thermoelectric devices, and turbo-compounding systems.

Phonon Sensor Dynamics for Cryogenic Dark Matter Search Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yen, Jeffrey

Understanding the quasiparticle diffusion process inside sputtered aluminum (Al thin films (~ 0.1-1 μm is critical for the Cryogenic Dark Matter Search (CDMS experiment to further optimize its detectors to directly search for dark matter. An initial study with Al films was undertaken by our group ~ 20 years ago, but some important questions were not answered at the time. This thesis can be considered a continuation of that critical study. The CDMS experiment utilizes high purity silicon and germanium crystals to simultaneously measure ionization and phonons created by particle interactions. In addition to describing some of the rich physicsmore » involved in simultaneously detecting ionization and phonons with a CDMS detector, this thesis focuses on the detailed physics of the phonon sensors themselves, which are patterned onto CDMS detector surfaces. CDMS detectors use thin sputtered Al films to collect phonon energy when it propagates to the surfaces of the detector crystals. The phonon energy breaks Cooper pairs and creates quasiparticles (qps). These qps diffuse until they get trapped in an proximitized “overlap” region where lower-Tc tungsten films connect to the Al film. These tungsten films are the transition edge sensors (W-TESs CDMS uses to readout phonon signals. We performed a wide range of experiments using several sets of test devices designed and fabricated specifically for this work. The devices were used mostly to study quasiparticle (qp transport in Al films and qp transmission through Al/W interfaces. The results of this work are being used to optimize the design of detectors for SuperCDMS SNOLAB. This thesis is intended for CDMS collaborators who are interested in knowing more about the detailed fundamentals of how our phonon sensors work so they can take full advantage of their benefits. However, this work can also be read by general readers who are interested in particle detection using TES technology. This thesis contains eight chapters. The first chapter gives basic background information about dark matter and searches for it. We then describe the basic CDMS detector technology in Chapter two. Chapter three focuses on superconductivity and explains some of the solid state physic most relevant to our Al and W film studies. We then turn our attention to the fabrication processes used to make test devices, and describe some of the studies done to characterize our W and Al film properties. Chapter five explains the experimental setup including how a 3He/4He dilution refrigerator works, and how our electronics were configured. We then get to chapter six where we present key experimental results. Chapter seven covers the TES model we used for our test devices to simulate the data pulse shapes and reconstruct the pulse energies. We also describe the diffusion models used to fit our data. Finally, we end with a short summary of our findings and provide a few suggestions for future studies.« less

Enzyme-Powered Pumps: From Fundamentals to Applications

NASA Astrophysics Data System (ADS)

Ortiz-Rivera, Isamar

Non-mechanical nano and microfluidic devices that function without the aid of an external power source, and can be tailored to meet specific needs, represent the next generation of smart devices. Recently, we have shown that surface-bound enzymes can act as pumps driving large-scale fluid flows in the presence of any substance that triggers the enzymatic reaction (e.g. substrate, co-factor, or biomarker). The fluid velocities attained in such systems depend directly on the enzymatic reaction rate and the concentration of the substance that initiates enzymatic catalysis. The use of biochemical reactions to power a micropump offers the advantages of specificity, sensitivity, and selectively, eliminating at the same time the need of an external power source, while providing biocompatibility. More importantly, these self-powered pumps overcome a significant obstacle in nano- and micro-fluidics: the need to use external pressure-driven pumps to push fluids through devices. Certainly, the development of enzyme-powered devices opens up new venues in biochemical engineering, particularly in the biomedical field. The work highlighted in this dissertation covers all the studies performed with enzyme-powered pumps, from the development of the micropump design, to the efforts invested in understanding the enzyme pump concept as a whole. The data collected to date, aims to expand our knowledge about enzyme-powered micropumps from the inside out: not only by exploring the different applications of these devices at the macroscale, but also by investigating in depth the mechanism of pump activation behind these systems. Specifically, we have focused on: (1) The general features that characterize the pumping behavior observed in enzyme-powered pumps, as well as the optimization of the device, (2) the possible mechanisms behind fluid motion, including the role of enzyme coverage and/or activity on the transduction of chemical energy into mechanical fluid flow in these devices, covering also the effect of the thermodynamics of the enzymatic reaction in the pumping behavior, and (3) the applicability of enzyme pumps as fluid flow-based inhibitor assays and as drug delivery devices. Our findings in each of these areas, gets us closer to our ultimate goal, where we aim to identify the optimal conditions needed for enzyme micropump operation, and construct a general model that could accurately predict enzyme micropump behavior for any enzyme-substrate combination. The information aforementioned has been divided in four chapters. Chapter 1 gives a quick glance into the development of enzyme-powered micropumps: from the systems and observed behaviors inspiring this work, to the first systems that were developed. The stability, duration, and extent of fluid pumping of enzyme pumps in general, are also discussed, along with the optimization of the enzyme-pump design. This chapter aims to provide a general idea of the motivation behind the concept of "enzyme-powered pumps", what are "enzyme-powered pumps", and which are the key features that characterize these systems. Chapter 2 is an extensive analysis of the mechanisms of actuation proposed for enzyme-powered micropumps. This chapter not only covers the first attempts to understand how enzyme pumps work, but also explores further the behavior of urease-powered pumps, which fluid flow patterns cannot be completely predicted only by considering thermal or solutal gradients. The findings of these studies could allow us to rationally control fluid flow for the directed delivery of payloads at designated locations. In Chapters 3 and 4, our focus was to highlight the potential application of enzyme-powered pumps for sensing and delivery. Chapter 3 explores the use of enzyme pumps as fluid flow-based inhibitor assays. At fixed concentrations of an enzyme and its substrate, the presence of an inhibitor can be detected by monitoring the decrease in fluid flow speed. Using this principle, sensors for toxic substances, like mercury, cyanide and azide, were designed using urease and catalase-powered pumps, respectively, with limits of detection well below the concentrations permitted by the Environmental Protection Agency (EPA). Chapter 4 demonstrates that, apart from their applicability as sensors, enzyme pumps can also be used for stimuli-responsive release, if the architecture applied for the design of the enzyme pump consists of a porous scaffold (e.g. hydrogel), that serves both as the platform for enzyme immobilization and as the host for guest molecules to be released. These proof-of-concept devices were developed with the idea of using the flows generated by enzymatic catalysis to power cargo release, only in the presence of the correct stimuli (e.g. release of insulin in the presence of glucose; release of antidotes in the presence of a toxic agent). In the cases studied, cargo release was directly proportional to the concentration of enzyme substrate in solution, highlighting the sensitivity of the device and its potential for drug delivery purposes. (Abstract shortened by Proquest.).

10 CFR 431.444 - Test procedures for the measurement of energy efficiency.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the following test methods: (1) Single-phase small electric motors: either IEEE Std 114, (incorporated...) Polyphase small electric motors less than or equal to 1 horsepower (0.746 kW): IEEE Std 112 (incorporated by... (0.746 kW): IEEE Std 112 (incorporated by reference, see § 431.443), Test Method B. ...

Study of Electromagnetic Wave Absorption Properties of Carbon Nanotubes-Based Composites

DTIC Science & Technology

2012-11-29

Publications: [1]. G. L. Zhao, Z. Ye, Z. Li, J. A. Roberts, "New carbon nanotube-epoxy composite for dampening microwave cavity resonance", IEEE Xplore ...Nanotechnology ( IEEE - NANO), 2012 12th IEEE Conference on 20-23 Aug. 2012. [2]. Z. Li, G. L. Zhao, P. Zhang, S. Guo, J. Tang, " Thermoelectric

Plasma Physics Applied (New Book)

NASA Astrophysics Data System (ADS)

Grabbe, Crockett

2007-03-01

0.5cm Plasma physics applications are one of the most rapidly growing fields in engineering & applied science today. The last decade alone has seen the rapid emergence of new applications such as dusty plasmas in the semiconductor and microchip industries, and plasma TVs. In addition, this last decade saw the achievement of the 50-year Lawson breakeven condition for fusion. With new discoveries in space plasma physics and applications to spacecraft for worldwide communication and space weather, as well as new applications being discovered, this diversity is always expanding. The new book Plasma Physics Applied reviews developments in several of these areas. Chapter 1 reviews the content and its authors, and is followed by a more comprehensive review of plasma physics applications in general in Chapter 2. Plasma applications in combustion and environmental uses are presented in Chapter 3. Lightning effects in planetary magnetospheres and potential application are described in Chapter 4. The area of dusty plasmas in both industrial and space plasmas and their applications are reviewed in Chapter 5. The particular area of Coulomb clusters in dusty plasmas is presented in Chapter 6. The variety of approaches to plasma confinement in magnetic devices for fusion are laid out in Chapter 7. Finally, an overview of plasma accelerator developments and their applications are presented in Chapter 8.

Portable Wireless LAN Device and Two-Way Radio Threat Assessment for Aircraft VHF Communication Radio Band

NASA Technical Reports Server (NTRS)

Nguyen, Truong X.; Koppen, Sandra V.; Ely, Jay J.; Williams, Reuben A.; Smith, Laura J.; Salud, Maria Theresa P.

2004-01-01

This document summarizes the safety analysis performed on a Flight Guidance System (FGS) requirements model. In particular, the safety properties desired of the FGS model are identified and the presence of the safety properties in the model is formally verified. Chapter 1 provides an introduction to the entire project, while Chapter 2 gives a brief overview of the problem domain, the nature of accidents, model based development, and the four-variable model. Chapter 3 outlines the approach. Chapter 4 presents the results of the traditional safety analysis techniques and illustrates how the hazardous conditions associated with the system trace into specific safety properties. Chapter 5 presents the results of the formal methods analysis technique model checking that was used to verify the presence of the safety properties in the requirements model. Finally, Chapter 6 summarizes the main conclusions of the study, first and foremost that model checking is a very effective verification technique to use on discrete models with reasonable state spaces. Additional supporting details are provided in the appendices.

Interoperation of an UHF RFID Reader and a TCP/IP Device via Wired and Wireless Links

PubMed Central

Lee, Sang Hoon; Jin, Ik Soo

2011-01-01

A main application in radio frequency identification (RFID) sensor networks is the function that processes real-time tag information after gathering the required data from multiple RFID tags. The component technologies that contain an RFID reader, called the interrogator, which has a tag chip, processors, coupling antenna, and a power management system have advanced significantly over the last decade. This paper presents a system implementation for interoperation between an UHF RFID reader and a TCP/IP device that is used as a gateway. The proposed system consists of an UHF RFID tag, an UHF RFID reader, an RF end-device, an RF coordinator, and a TCP/IP I/F. The UHF RFID reader, operating at 915 MHz, is compatible with EPC Class-0/Gen1, Class-1/Gen1 and 2, and ISO18000-6B. In particular, the UHF RFID reader can be combined with the RF end-device/coordinator for a ZigBee (IEEE 802.15.4) interface, which is a low-power wireless standard. The TCP/IP device communicates with the RFID reader via wired links. On the other hand, it is connected to the ZigBee end-device via wireless links. The web based test results show that the developed system can remotely recognize information of multiple tags through the interoperation between the RFID reader and the TCP/IP device. PMID:22346665

Interoperation of an UHF RFID reader and a TCP/IP device via wired and wireless links.

PubMed

Lee, Sang Hoon; Jin, Ik Soo

2011-01-01

A main application in radio frequency identification (RFID) sensor networks is the function that processes real-time tag information after gathering the required data from multiple RFID tags. The component technologies that contain an RFID reader, called the interrogator, which has a tag chip, processors, coupling antenna, and a power management system have advanced significantly over the last decade. This paper presents a system implementation for interoperation between an UHF RFID reader and a TCP/IP device that is used as a gateway. The proposed system consists of an UHF RFID tag, an UHF RFID reader, an RF end-device, an RF coordinator, and a TCP/IP I/F. The UHF RFID reader, operating at 915 MHz, is compatible with EPC Class-0/Gen1, Class-1/Gen1 and 2, and ISO18000-6B. In particular, the UHF RFID reader can be combined with the RF end-device/coordinator for a ZigBee (IEEE 802.15.4) interface, which is a low-power wireless standard. The TCP/IP device communicates with the RFID reader via wired links. On the other hand, it is connected to the ZigBee end-device via wireless links. The web based test results show that the developed system can remotely recognize information of multiple tags through the interoperation between the RFID reader and the TCP/IP device.

47 CFR 90.103 - Radiolocation Service.

Code of Federal Regulations, 2013 CFR

2013-10-01

... limited to survey operations using transmitters with a peak power not to exceed 5 watts into the antenna... requirements of §§ 90.403(c), 90.403(f), and 90.429 of this part. (23) Devices designed to operate as field... sensors as set forth in part 15 of this chapter. (24) Devices designed to operate as field disturbance...

47 CFR 90.103 - Radiolocation Service.

Code of Federal Regulations, 2014 CFR

2014-10-01

... limited to survey operations using transmitters with a peak power not to exceed 5 watts into the antenna... requirements of §§ 90.403(c), 90.403(f), and 90.429 of this part. (23) Devices designed to operate as field... sensors as set forth in part 15 of this chapter. (24) Devices designed to operate as field disturbance...

10 CFR 35.49 - Suppliers for sealed sources or devices for medical use.

Code of Federal Regulations, 2014 CFR

2014-01-01

... accordance with a license issued under 10 CFR part 30 and 10 CFR 32.74 of this chapter or equivalent requirements of an Agreement State; (b) Sealed sources or devices non-commercially transferred from a Part 35... in accordance with a license issued under 10 CFR part 30 or the equivalent requirements of an...

10 CFR 35.49 - Suppliers for sealed sources or devices for medical use.

Code of Federal Regulations, 2011 CFR

2011-01-01

... accordance with a license issued under 10 CFR Part 30 and 10 CFR 32.74 of this chapter or equivalent requirements of an Agreement State; (b) Sealed sources or devices non-commercially transferred from a Part 35... in accordance with a license issued under 10 CFR Part 30 or the equivalent requirements of an...

10 CFR 35.49 - Suppliers for sealed sources or devices for medical use.

Code of Federal Regulations, 2010 CFR

2010-01-01

... accordance with a license issued under 10 CFR Part 30 and 10 CFR 32.74 of this chapter or equivalent requirements of an Agreement State; (b) Sealed sources or devices non-commercially transferred from a Part 35... in accordance with a license issued under 10 CFR Part 30 or the equivalent requirements of an...

10 CFR 35.49 - Suppliers for sealed sources or devices for medical use.

Code of Federal Regulations, 2012 CFR

2012-01-01

... accordance with a license issued under 10 CFR Part 30 and 10 CFR 32.74 of this chapter or equivalent requirements of an Agreement State; (b) Sealed sources or devices non-commercially transferred from a Part 35... in accordance with a license issued under 10 CFR Part 30 or the equivalent requirements of an...

10 CFR 35.49 - Suppliers for sealed sources or devices for medical use.

Code of Federal Regulations, 2013 CFR

2013-01-01

... accordance with a license issued under 10 CFR Part 30 and 10 CFR 32.74 of this chapter or equivalent requirements of an Agreement State; (b) Sealed sources or devices non-commercially transferred from a Part 35... in accordance with a license issued under 10 CFR Part 30 or the equivalent requirements of an...

Study of Allocation Guaranteed Time Slot Wireless Body Area Networks Based on IEEE 802.15.4

NASA Astrophysics Data System (ADS)

Yundra, E.; Harsono, G. D.

2018-04-01

This paper aims to determine the size of the Guaranteed Time Slot (GTS) on the super frame structure required for each sensor as well as to know the performance of the GTS resized system compared to the GTS standard on IEEE 802.15.4. This article proposes a scheme to improve IEEE 802.15.4 medium access control, called allocation Guaranteed Time Slot (ALGATIS). ALGATIS is expected to effectively allocate guaranteed time slot to the requested sensors, it adjusts the length of the slot in super frame duration based on the length of the packet data. This article presents a simulation experiment of IEEE 802.15.4, especially for star network, to predict the throughput of networks and average energy consumption. The simulation experiments show that the performance of ALGATIS is better than that of IEEE 802.15.4 standard in term of the throughput of networks and average energy consumption

Low-temperature electronic transport in one-dimensional hybrid systems: Metal cluster embedded carbon nanotubes

NASA Astrophysics Data System (ADS)

Soldano, Caterina

The investigation of the electronic and magnetotransport properties at low temperature in individual MWNT with embedded clusters are here presented. The majority of studies of transport in MWNT reported in literature has been carried out on arc-discharge grown tubes, generally considered "clean" and defect-free. In this project, individual MWNT grown in alumina template are used; these tubes are highly disordered compared for example to arc-discharge ones, conditions that dramatically will impact the charge transport. As-fabricated devices are in general highly resistive. A large decrease in the value of the device resistance can be achieved through a controlled and fast high-bias sweep method (HBT) across the sample. Scanning electron microscopy analysis shows that this method induces a metal (platinum) decoration of the MWNT surface as a consequence of the large amount of Joule heating developed during the sweep. Temperature dependence study (5

Gate-controlled-diodes in silicon-on-sapphire: A computer simulation

NASA Technical Reports Server (NTRS)

Gassaway, J. D.

1974-01-01

The computer simulation of the electrical behavior of a Gate-Controlled Diode (GCD) fabricated in Silicon-On-Sapphire (SOS) was described. A procedure for determining lifetime profiles from capacitance and reverse current measurements on the GCD was established. Chapter 1 discusses the SOS structure and points out the need of lifetime profiles to assist in device design for GCD's and bipolar transistors. Chapter 2 presents the one-dimensional analytical formula for electrostatic analysis of the SOS-GCD which are useful for data interpretation and setting boundary conditions on a simplified two-dimensional analysis. Chapter 3 gives the results of a two-dimensional analysis which treats the field as one-dimensional until the silicon film is depleted and the field penetrates the sapphire substrate. Chapter 4 describes a more complete two-dimensional model and gives results of programs implementing the model.

Strategies toward High Performance Organic Photovoltaic Cell: Material and Process

NASA Astrophysics Data System (ADS)

Kim, Bong Gi

The power conversion efficiency of organic photovoltaic (OPV) cells has been rapidly improved during the last few years and currently reaches around 10 %. The performance is evenly governed by absorption, exciton diffusion, exciton dissociation, carrier transfer, and collection efficiencies. Establishing a better understanding of OPV device physics combined with the development of new materials for each executive step contributes to this dramatic improvement. This dissertation focuses mainly on material design and development to correlate the intrinsic properties of organic semiconductors and the OPV performance. The introductory Chapter 1 briefly reviews the motivation of OPV research, its working mechanism, and representative organic materials for OPV application. Chapter 2 discusses the modulation of conjugated polymer's (CP's) absorption behavior and an efficient semi-empirical approach to predict CP's energy levels from its constituent monomers' HOMO/LUMO values. A strong acceptor lowered both the HOMO and LUMO levels of the CP, but the LUMO dropped more rapidly which ultimately produced a narrowed band-gap in the electron donating/accepting alternating copolymer system. In addition, the energy level difference between the CP and the constituent monomers converged to a constant value, providing an energy level prediction tool. Chapter 3 illustrates the systematic investigation on the relationship between the molecular structure of an energy harvesting organic dye and the exciton dissociation efficiency. The study showed that the quantum yield decreased as the exciton binding energy increases, and dipole moment direction should be properly oriented in the dye framework in order to improve photo-current generation when used in a dye sensitized photovoltaic device. Chapter 4 demonstrates the ultrasonic-assisted self-assembly of CPs in solution, rapidly and efficiently. Ultrasonication combined with dipolar media accelerated CP's aggregation, and the effect of CP's aggregation on the enhancement of OPV performance by promoting photo-current generation and increasing carrier mobility was systematically investigated. The correlation between the chemical structure of a CP and it aggregation behavior is further described in Chapter 5. To promote CP aggregate, a planar chain conformation was advantageous and CP aggregation improved hole mobility in the OPV device. However, thermally induced CP aggregates caused strong charge recombination, resulting in open circuit voltage drop. In Chapter 6, a novel polymer design principle to enable directed CP alignment is discussed. Regulating chain planarity and preventing massive crystallization of CP achieved by the developed molecular design principle allowed directed CP alignment under small shear flow.

Design and commissioning of a 16.1 MHz multiharmonic buncher for the reaccelerator at NSCL

NASA Astrophysics Data System (ADS)

Alt, Daniel Maloney

The ReAccelerator (ReA) linear accelerator facility at the National Superconducting Cyclotron Laboratory is a unique resource for the nuclear physics community. The particle fragmentation beam production technique, combined with the ability to stop and then reaccelerate the beam to energies of astrophysical interest, give experimenters an unprecedented range of rare isotopes at energies of nuclear and astrophysical interest. The ReAccelerator also functions as a testbed for technology to be incorporated in the upcoming Facility for Rare Isotope Beams linear accelerator, which will eventually in turn become the beam source for ReA. This prototype nature of the ReAccelerator, however, dictated some design choices which have resulted in a final beam with a time structure that is less than ideal for certain classes of experiments. The cavities and RFQ used in ReA have an operating frequency of 80.5 MHz, which corresponds to a separation between particle bunches at the detectors of 12.4 ns. While this separation is acceptable for many experiments, sensitive time of flight measurements require a greater separation between pulses. As nuclear physics experiments rely on statistics, a solution to increasing bunch separation without simply discarding a large fraction of the beam particles was desired. This document describes the design and construction of such a device, a 16.1 MHz multiharmonic buncher. The first chapter provides backgound information on the NSCL and ReA, and some basic concepts in accelerator physics to lay the groundwork for the project.Next, more specifics are provided on the time structure of accelerated beams, and the experimental motivation for greater separation. The third chapter outlines the basic principles of multiharmonic bunching. In order to evaluate the feasibility of any buncher design, the exact acceptance of the Radiofrequency Quadrupole (RFQ) of the ReAccelerator needed to be empirically measured. Chapter 4 describes the results of that measurement. Chapter 5 outlines the simulations and calculations that went into the design choices for this particular buncher, incorporating the results of the RFQ measurements. The next two chapters describe the construction, installation, and testing of the device, and give experimental results. Finally, Chapter 8 summarizes the project and the final steps which need to be undertaken to make the device a simple to use asset for future experimentalists at ReA.

The study of electromagnetic wave propagation in photonic crystals via planewave based transfer (scattering) matrix method with active gain material applications

NASA Astrophysics Data System (ADS)

Li, Ming

In this dissertation, a set of numerical simulation tools are developed under previous work to efficiently and accurately study one-dimensional (1D), two-dimensional (2D), 2D slab and three-dimensional (3D) photonic crystal structures and their defects effects by means of spectrum (transmission, reflection, absorption), band structure (dispersion relation), and electric and/or magnetic fields distribution (mode profiles). Further more, the lasing property and spontaneous emission behaviors are studied when active gain materials are presented in the photonic crystal structures. First, the planewave based transfer (scattering) matrix method (TMM) is described in every detail along with a brief review of photonic crystal history (Chapter 1 and 2). As a frequency domain method, TMM has the following major advantages over other numerical methods: (1) the planewave basis makes Maxwell's Equations a linear algebra problem and there are mature numerical package to solve linear algebra problem such as Lapack and Scalapack (for parallel computation). (2) Transfer (scattering) matrix method make 3D problem into 2D slices and link all slices together via the scattering matrix (S matrix) which reduces computation time and memory usage dramatically and makes 3D real photonic crystal devices design possible; and this also makes the simulated domain no length limitation along the propagation direction (ideal for waveguide simulation). (3) It is a frequency domain method and calculation results are all for steady state, without the influences of finite time span convolution effects and/or transient effects. (4) TMM can treat dispersive material (such as metal at visible light) naturally without introducing any additional computation; and meanwhile TMM can also deal with anisotropic material and magnetic material (such as perfectly matched layer) naturally from its algorithms. (5) Extension of TMM to deal with active gain material can be done through an iteration procedure with gain material expressed by electric field dependent dielectric constant. Next, the concepts of spectrum interpolation (Chapter 3), higher-order incident (Chapter 4) and perfectly matched layer (Chapter 5) are introduced and applied to TMM, with detailed simulation for 1D, 2D, and 3D photonic crystal examples. Curvilinear coordinate transform is applied to the Maxwell's Equations to study waveguide bend (Chapter 6). By finding the phase difference along propagation direction at various XY plane locations, the behaviors of electromagnetic wave propagation (such as light bending, focusing etc) can be studied (Chapter 7), which can be applied to diffractive optics for new devices design. Numerical simulation tools for lasing devices are usually based on rate equations which are not accurate above the threshold and for small scale lasing cavities (such as nano-scale cavities). Recently, we extend the TMM package function to include the capacity of dealing active gain materials. Both lasing (above threshold) and spontaneous emission (below threshold) can be studied in the frame work of our Gain-TMM algorithm. Chapter 8 will illustrate the algorithm in detail and show the simulation results for 3D photonic crystal lasing devices. Then, microwave experiments (mainly resonant cavity embedded at layer-by-layer woodpile structures) are performed at Chapter 9 as an efficient practical way to study photonic crystal devices. The size of photonic crystal under microwave region is at the order of centimeter which makes the fabrication easier to realize. At the same time due to the scaling property, the result of microwave experiments can be applied directly to optical or infrared frequency regions. The systematic TMM simulations for various resonant cavities are performed and consistent results are obtained when compared with microwave experiments. Besides scaling the experimental results to much smaller wavelength, designing potential photonic crystal devices for application at microwave is also an interesting and important topic. Finally, we describe the future development of TMM algorithm such as using localized functions as basis to more efficiently simulate disorder problems (Chapter 10). Future applications of photonic crystal concepts are also discussed at Chapter 10. Along with this dissertation, TMM Photonic Crystal Package User Manual and Gain TMM Photonic Crystal Package User Manual written by me, Dr. Jiangrong Cao (Canon USA) and Dr. Xinhua Hu (Ames Lab) focus more on the programming detail, software user interface, trouble shooting, and step-by-step instructions. This dissertation and the two user manuals are essential documents for TMM software package beginners and advanced users. Future software developments, new version releases and FAQs can be tracked through my web page: http://www.public.iastate.edu/~mli/ In summary, this dissertation has extended the planewave based transfer (scattering) matrix method in many aspects which make the TMM and Gain-TMM software package a powerful simulation tool in photonic crystal study. Comparisons of TMM and GTMM results with other published numerical results and experimental results indicate that TMM and GTMM is accurate and highly efficient in photonic crystal device simulation and design. (Abstract shortened by UMI.)

Performance of the Sleep-Mode Mechanism of the New IEEE 802.16m Proposal for Correlated Downlink Traffic

NASA Astrophysics Data System (ADS)

de Turck, Koen; de Vuyst, Stijn; Fiems, Dieter; Wittevrongel, Sabine; Bruneel, Herwig

There is a considerable interest nowadays in making wireless telecommunication more energy-efficient. The sleep-mode mechanism in WiMAX (IEEE 802.16e) is one of such energy saving measures. Recently, Samsung proposed some modifications on the sleep-mode mechanism, scheduled to appear in the forthcoming IEEE 802.16m standard, aimed at minimizing the signaling overhead. In this work, we present a performance analysis of this proposal and clarify the differences with the standard mechanism included in IEEE 802.16e. We also propose some special algorithms aimed at reducing the computational complexity of the analysis.

Genomics, molecular imaging, bioinformatics, and bio-nano-info integration are synergistic components of translational medicine and personalized healthcare research.

PubMed

Yang, Jack Y; Yang, Mary Qu; Arabnia, Hamid R; Deng, Youping

2008-09-16

Supported by National Science Foundation (NSF), International Society of Intelligent Biological Medicine (ISIBM), International Journal of Computational Biology and Drug Design and International Journal of Functional Informatics and Personalized Medicine, IEEE 7th Bioinformatics and Bioengineering attracted more than 600 papers and 500 researchers and medical doctors. It was the only synergistic inter/multidisciplinary IEEE conference with 24 Keynote Lectures, 7 Tutorials, 5 Cutting-Edge Research Workshops and 32 Scientific Sessions including 11 Special Research Interest Sessions that were designed dynamically at Harvard in response to the current research trends and advances. The committee was very grateful for the IEEE Plenary Keynote Lectures given by: Dr. A. Keith Dunker (Indiana), Dr. Jun Liu (Harvard), Dr. Brian Athey (Michigan), Dr. Mark Borodovsky (Georgia Tech and President of ISIBM), Dr. Hamid Arabnia (Georgia and Vice-President of ISIBM), Dr. Ruzena Bajcsy (Berkeley and Member of United States National Academy of Engineering and Member of United States Institute of Medicine of the National Academies), Dr. Mary Yang (United States National Institutes of Health and Oak Ridge, DOE), Dr. Chih-Ming Ho (UCLA and Member of United States National Academy of Engineering and Academician of Academia Sinica), Dr. Andy Baxevanis (United States National Institutes of Health), Dr. Arif Ghafoor (Purdue), Dr. John Quackenbush (Harvard), Dr. Eric Jakobsson (UIUC), Dr. Vladimir Uversky (Indiana), Dr. Laura Elnitski (United States National Institutes of Health) and other world-class scientific leaders. The Harvard meeting was a large academic event 100% full-sponsored by IEEE financially and academically. After a rigorous peer-review process, the committee selected 27 high-quality research papers from 600 submissions. The committee is grateful for contributions from keynote speakers Dr. Russ Altman (IEEE BIBM conference keynote lecturer on combining simulation and machine learning to recognize function in 4D), Dr. Mary Qu Yang (IEEE BIBM workshop keynote lecturer on new initiatives of detecting microscopic disease using machine learning and molecular biology, http://ieeexplore.ieee.org/servlet/opac?punumber=4425386) and Dr. Jack Y. Yang (IEEE BIBM workshop keynote lecturer on data mining and knowledge discovery in translational medicine) from the first IEEE Computer Society BioInformatics and BioMedicine (IEEE BIBM) international conference and workshops, November 2-4, 2007, Silicon Valley, California, USA.

Genomics, molecular imaging, bioinformatics, and bio-nano-info integration are synergistic components of translational medicine and personalized healthcare research

PubMed Central

2008-01-01

Supported by National Science Foundation (NSF), International Society of Intelligent Biological Medicine (ISIBM), International Journal of Computational Biology and Drug Design and International Journal of Functional Informatics and Personalized Medicine, IEEE 7th Bioinformatics and Bioengineering attracted more than 600 papers and 500 researchers and medical doctors. It was the only synergistic inter/multidisciplinary IEEE conference with 24 Keynote Lectures, 7 Tutorials, 5 Cutting-Edge Research Workshops and 32 Scientific Sessions including 11 Special Research Interest Sessions that were designed dynamically at Harvard in response to the current research trends and advances. The committee was very grateful for the IEEE Plenary Keynote Lectures given by: Dr. A. Keith Dunker (Indiana), Dr. Jun Liu (Harvard), Dr. Brian Athey (Michigan), Dr. Mark Borodovsky (Georgia Tech and President of ISIBM), Dr. Hamid Arabnia (Georgia and Vice-President of ISIBM), Dr. Ruzena Bajcsy (Berkeley and Member of United States National Academy of Engineering and Member of United States Institute of Medicine of the National Academies), Dr. Mary Yang (United States National Institutes of Health and Oak Ridge, DOE), Dr. Chih-Ming Ho (UCLA and Member of United States National Academy of Engineering and Academician of Academia Sinica), Dr. Andy Baxevanis (United States National Institutes of Health), Dr. Arif Ghafoor (Purdue), Dr. John Quackenbush (Harvard), Dr. Eric Jakobsson (UIUC), Dr. Vladimir Uversky (Indiana), Dr. Laura Elnitski (United States National Institutes of Health) and other world-class scientific leaders. The Harvard meeting was a large academic event 100% full-sponsored by IEEE financially and academically. After a rigorous peer-review process, the committee selected 27 high-quality research papers from 600 submissions. The committee is grateful for contributions from keynote speakers Dr. Russ Altman (IEEE BIBM conference keynote lecturer on combining simulation and machine learning to recognize function in 4D), Dr. Mary Qu Yang (IEEE BIBM workshop keynote lecturer on new initiatives of detecting microscopic disease using machine learning and molecular biology, http://ieeexplore.ieee.org/servlet/opac?punumber=4425386) and Dr. Jack Y. Yang (IEEE BIBM workshop keynote lecturer on data mining and knowledge discovery in translational medicine) from the first IEEE Computer Society BioInformatics and BioMedicine (IEEE BIBM) international conference and workshops, November 2-4, 2007, Silicon Valley, California, USA. PMID:18831773

IEEE 1588 Time Synchronization Board in MTCA.4 Form Factor

NASA Astrophysics Data System (ADS)

Jabłoński, G.; Makowski, D.; Mielczarek, A.; Orlikowski, M.; Perek, P.; Napieralski, A.; Makijarvi, P.; Simrock, S.

2015-06-01

Distributed data acquisition and control systems in large-scale scientific experiments, like e.g. ITER, require time synchronization with nanosecond precision. A protocol commonly used for that purpose is the Precise Timing Protocol (PTP), also known as IEEE 1588 standard. It uses the standard Ethernet signalling and protocols and allows obtaining timing accuracy of the order of tens of nanoseconds. The MTCA.4 is gradually becoming the platform of choice for building such systems. Currently there is no commercially available implementation of the PTP receiver on that platform. In this paper, we present a module in the MTCA.4 form factor supporting this standard. The module may be used as a timing receiver providing reference clocks in an MTCA.4 chassis, generating a Pulse Per Second (PPS) signal and allowing generation of triggers and timestamping of events on 8 configurable backplane lines and two front panel connectors. The module is based on the Xilinx Spartan 6 FPGA and thermally stabilized Voltage Controlled Oscillator controlled by the digital-to-analog converter. The board supports standalone operation, without the support from the host operating system, as the entire control algorithm is run on a Microblaze CPU implemented in the FPGA. The software support for the card includes the low-level API in the form of Linux driver, user-mode library, high-level API: ITER Nominal Device Support and EPICS IOC. The device has been tested in the ITER timing distribution network (TCN) with three cascaded PTP-enabled Hirschmann switches and a GPS reference clock source. An RMS synchronization accuracy, measured by direct comparison of the PPS signals, better than 20 ns has been obtained.

Coordinative Voltage Control Strategy with Multiple Resources for Distribution Systems of High PV Penetration: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Xiangqi; Zhang, Yingchen

This paper presents an optimal voltage control methodology with coordination among different voltage-regulating resources, including controllable loads, distributed energy resources such as energy storage and photovoltaics (PV), and utility voltage-regulating devices such as voltage regulators and capacitors. The proposed methodology could effectively tackle the overvoltage and voltage regulation device distortion problems brought by high penetrations of PV to improve grid operation reliability. A voltage-load sensitivity matrix and voltage-regulator sensitivity matrix are used to deploy the resources along the feeder to achieve the control objectives. Mixed-integer nonlinear programming is used to solve the formulated optimization control problem. The methodology has beenmore » tested on the IEEE 123-feeder test system, and the results demonstrate that the proposed approach could actively tackle the voltage problem brought about by high penetrations of PV and improve the reliability of distribution system operation.« less

Enhancing functional electrical stimulation for emerging rehabilitation robotics in the framework of HYPER project.

PubMed

Brunetti, F; Garay, Á; Moreno, J C; Pons, J L

2011-01-01

This paper presents the development of a novel functional electrical stimulation (FES) system. New approaches in emerging rehabilitation robotics propose the use of residual muscular activity or limbs movements during the rehabilitation process of neuromotor. More ambitious projects propose the use of FES systems to restore or compensate motor capabilities by controlling existing muscles or subject limbs. These emerging approaches require more sophisticated FES devices in terms of channels, signals controls and portability. In the framework of HYPER project, such devices are being developed to support the main objective of the project: the development of neurorobots and neuroprosthetics to restore functional motor capabilities in patients who suffered cerebrovascular accidents or spinal cord injury. The presented portable FES system includes novel elec-trostimulator circuits and improved channel switching capacities to enable emerging approaches in rehabilitation robotics. © 2011 IEEE

Development and application of General Purpose Data Acquisition Shell (GPDAS) at advanced photon source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, Youngjoo; Kim, Keeman.

1991-01-01

An operating system shell GPDAS (General Purpose Data Acquisition Shell) on MS-DOS-based microcomputers has been developed to provide flexibility in data acquisition and device control for magnet measurements at the Advanced Photon Source. GPDAS is both a command interpreter and an integrated script-based programming environment. It also incorporates the MS-DOS shell to make use of the existing utility programs for file manipulation and data analysis. Features include: alias definition, virtual memory, windows, graphics, data and procedure backup, background operation, script programming language, and script level debugging. Data acquisition system devices can be controlled through IEEE488 board, multifunction I/O board, digitalmore » I/O board and Gespac crate via Euro G-64 bus. GPDAS is now being used for diagnostics R D and accelerator physics studies as well as for magnet measurements. Their hardware configurations will also be discussed. 3 refs., 3 figs.« less

Access Protocol For An Industrial Optical Fibre LAN

NASA Astrophysics Data System (ADS)

Senior, John M.; Walker, William M.; Ryley, Alan

1987-09-01

A structure for OSI levels 1 and 2 of a local area network suitable for use in a variety of industrial environments is reported. It is intended that the LAN will utilise optical fibre technology at the physical level and a hybrid of dynamically optimisable token passing and CSMA/CD techniques at the data link (IEEE 802 medium access control - logical link control) level. An intelligent token passing algorithm is employed which dynamically allocates tokens according to the known upper limits on the requirements of each device. In addition a system of stochastic tokens is used to increase efficiency when the stochastic traffic is significant. The protocol also allows user-defined priority systems to be employed and is suitable for distributed or centralised implementation. The results of computer simulated performance characteristics for the protocol using a star-ring topology are reported which demonstrate its ability to perform efficiently with the device and traffic loads anticipated within an industrial environment.

Influence of TCSC Devices on Congestion Management in a Deregulated Power System Using Evolutionary Programming Technique

NASA Astrophysics Data System (ADS)

Ananthichristy, A., Dr.; Elanthirayan, R.; Brindha, R., Dr.; Siddhiq, M. S.; Venkatesh, N.; Harshit, M. V.; Nikhilreddy, M.

2018-04-01

Congestion management is one of the technical challenges in power system deregulation. In deregulated electricity market it may always not be possible to dispatch all of the contracted power transactions due to congestion of the transmission corridors. Transmission congestion occurs when there is insufficient transmission capacity to simultaneously accommodate all constraints for transmission of a line. Flexible Alternative Current Transmission System (FACTS) devices can be an alternative to reduce the flows in the heavily loaded lines, resulting in an increased loadability, low system loss, improved stability of the network, reduced cost of production and fulfilled contractual requirement by controlling the power flow in the network. A method to determine the optimal location of FACTS has been suggested based on reduction of total system VAR power losses. The simulation was done on IEEE 14 bus system and results were obtained.

Medical instrument data exchange.

PubMed

Gumudavelli, Suman; McKneely, Paul K; Thongpithoonrat, Pongnarin; Gurkan, D; Chapman, Frank M

2008-01-01

Advances in medical devices and health care has been phenomenal during the recent years. Although medical device manufacturers have been improving their instruments, network connection of these instruments still rely on proprietary technologies. Even if the interface has been provided by the manufacturer (e.g., RS-232, USB, or Ethernet coupled with a proprietary API), there is no widely-accepted uniform data model to access data of various bedside instruments. There is a need for a common standard which allows for internetworking with the medical devices from different manufacturers. ISO/IEEE 11073 (X73) is a standard attempting to unify the interfaces of all medical devices. X73 defines a client access mechanism that would be implemented into the communication controllers (residing between an instrument and the network) in order to access/network patient data. On the other hand, MediCAN technology suite has been demonstrated with various medical instruments to achieve interfacing and networking with a similar goal in its open standardization approach. However, it provides a more generic definition for medical data to achieve flexibility for networking and client access mechanisms. In this paper, a comparison between the data model of X73 and MediCAN will be presented to encourage interoperability demonstrations of medical instruments.

10 CFR 431.444 - Test procedures for the measurement of energy efficiency.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the following test methods: (1) Single-phase small electric motors: Either IEEE Std 114-2010 or CSA... to 1 horsepower (0.75 kW): Either IEEE Std 112-2004 Test Method A or CSA C747 (incorporated by...): Either IEEE Std 112-2004 Test Method B or CSA C390-10 (incorporated by reference, see § 431.443). [74 FR...

10 CFR 431.444 - Test procedures for the measurement of energy efficiency.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the following test methods: (1) Single-phase small electric motors: Either IEEE Std 114-2010 or CSA... to 1 horsepower (0.75 kW): Either IEEE Std 112-2004 Test Method A or CSA C747 (incorporated by...): Either IEEE Std 112-2004 Test Method B or CSA C390-10 (incorporated by reference, see § 431.443). [74 FR...

Virtualization of AEGIS: A Study of the Feasibility of Applying Open Architecture Technology to the Surface Navy’s Most Complex Automated Weapon System

DTIC Science & Technology

2011-09-01

diagnostics system. Aerospace and Electronic Systems Magazine, IEEE , 9(2), 40–45. Current version released August 2002 in IEEE Xplore . doi: 10.1109...Cramming more components onto integrated circuits. Electronics, 114–117. Reprinted January 1998 in Proceedings of the IEEE , 86(1), 82–85. doi: S 0018

ARO PECASE: Information Assurance for Energy-Constrained Wireless Sensor Networks

DTIC Science & Technology

2011-12-21

Distribution, 18th Annual IEEE International Symposium on Personal, Indoor, and Mobile Radio Communications (PIMRC), September 2007. 2. 2010 IEEE...received the following awards: Student Best Paper Award at the IEEE International Symposium on Personal, Indoor, and Mobile Radio Communications (PIMRC...Localization in Wireless Ad Hoc Networks – Many current and future appli- cations of mobile ad hoc networks, including disaster response and event

Magnetic tunnel spin injectors for spintronics

NASA Astrophysics Data System (ADS)

Wang, Roger

Research in spin-based electronics, or "spintronics", has a universal goal to develop applications for electron spin in a broad range of electronics and strives to produce low power nanoscale devices. Spin injection into semiconductors is an important initial step in the development of spintronic devices, with the goal to create a highly spin polarized population of electrons inside a semiconductor at room temperature for study, characterization, and manipulation. This dissertation investigates magnetic tunnel spin injectors that aim to meet the spin injection requirements needed for potential spintronic devices. Magnetism and spin are inherently related, and chapter 1 provides an introduction on magnetic tunneling and spintronics. Chapter 2 then describes the fabrication of the spin injector structures studied in this dissertation, and also illustrates the optical spin detection technique that correlates the measured electroluminescence polarization from quantum wells to the electron spin polarization inside the semiconductor. Chapter 3 reports the spin injection from the magnetic tunnel transistor (MTT) spin injector, which is capable of producing highly spin polarized tunneling currents by spin selective scattering in its multilayer structure. The MTT achieves ˜10% lower bound injected spin polarization in GaAs at 1.4 K. Chapter 4 reports the spin injection from CoFe-MgO(100) tunnel spin injectors, where spin dependent tunneling through MgO(100) produces highly spin polarized tunneling currents. These structures achieve lower bound spin polarizations exceeding 50% at 100 K and 30% in GaAs at 290 K. The CoFe-MgO spin injectors also demonstrate excellent thermal stability, maintaining high injection efficiencies even after exposure to temperatures of up to 400 C. Bias voltage and temperature dependent studies on these structures indicate a significant dependence of the electroluminescence polarization on the spin and carrier recombination lifetimes inside the semiconductor. Chapter 5 investigates these spin and carrier lifetime effects on the electroluminescence polarization using time resolved optical techniques. These studies suggest that a peak in the carrier lifetime with temperature is responsible for the nonmonotonic temperature dependence observed in the electroluminescence polarization, and that the initially injected spin polarization from CoFe-MgO spin injectors is a nearly temperature independent ˜70% from 10 K up to room temperature.

Distance Estimation Using Handheld Devices

DTIC Science & Technology

2013-06-01

each and all centered in the pin that marks the location of the device. ................................47 Figure 21. Form interface where the UFO ...SIFT Scale-invariant feature transform SURF Speed up Robust Features SAD Sum of Absolute Distance UFOs Untrained Forward Observers WHATWG Web...Forward Observers ( UFOs ) to make a successful call for fire. This chapter presents the solution from different aspects and is organized as follows

77 FR 5735 - Importation of Arms, Ammunition and Implements of War and Machine Guns, Destructive Devices, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-06

... Implements of War and Machine Guns, Destructive Devices, and Certain Other Firearms; Extending the Term of... U.S.C. Chapter 53. The Attorney General is also responsible for enforcing the provisions of the Gun... application must be submitted for a permit to cover the unshipped balance. B. Importation of Machine Guns...

Digital Readers: The Next Chapter in E-Book Reading and Response

ERIC Educational Resources Information Center

Larson, Lotta C.

2010-01-01

The basic features of digital reading devices (such as the Amazon Kindle) are described in this article. The author also considers how such devices can advance e-book readership among primary students by offering new avenues for accessing and interacting with a wide array of texts. Rooted in the transactional theory of reader response and a new…

46 CFR 119.440 - Independent fuel tanks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Specification (latest edition) [see also § 114.600 of this chapter] Thickness in millimeters (inches) & [gage... protected from mechanical damage, and provided at the tank connections with devices that will automatically...

"Data Acquisition Systems"

DOE Office of Scientific and Technical Information (OSTI.GOV)

Unterweger, Michael; Costrell, Louis deceased

2009-07-07

This project involved support for Lou Costrell and myself in the development of IEEE and IEC standards for nuclear counting and data acquisition systems. Over the years, as a result of this support, Lou and I were able to attend standards meetings of IEEE and IEC, which led directly to the publication of many standards for NIM systems, FastBus and CAMAC. We also chaired several writing committees as well as ANSI N42 (Nuclear instrumentation), IEEE NIM (NIM standard), IEEE NID (NPSS nuclear instruments and detector) and IEC TC45 WG9 (Nuclear instrumentation). Through this support we were able to assure thatmore » the interests of the US and DOE were expressed and implemented in the various standards.« less

Silicon photonics: Design, fabrication, and characterization of on-chip optical interconnects

NASA Astrophysics Data System (ADS)

Hsieh, I.-Wei

In recent years, the research field of silicon photonics has been developing rapidly from a concept to a demonstrated technology, and has gathered much attention from both academia and industry communities. Its many potential applications in long-haul telecommunication, mid-range data-communication, on-chip optical interconnection networks, and nano-scale sensing as well as its compatibility with electronic integrated circuits have driven much effort in realizing silicon photonics both as a disruptive technology for existing markets and as an enabling technology for new ones. Despite the promising future of silicon photonics, many fundamental issues still remain to be understood---both in the linear- and nonlinear-optical regimes. There are also many engineering challenges to make silicon photonics the gold standard in photonic integrated circuits. In this thesis, we focus on the design, fabrication, and characterization of active and passive silicon-on-insulator (SOI) photonic devices. The SOI material system differs from most conventional optical material platforms because of its high-refractive-index-contrast, which enables engineers to design very compact integrated photonic networks with sub-micron transverse waveguide dimensions and sharp bends. On the other hand, because most analytical formulas for designing waveguide devices are valid only in low-index-contrast cases, SOI photonic devices need to be analyzed numerically for accurate results. The second chapter of this thesis describes some common numerical methods such as Beam Propagation Method (BPM) and Finite Element Method (FEM) for waveguide-design simulations, and presents two design studies based on these methods. The compatibility of silicon photonic integrated circuits with conventional CMOS fabrication technology is another important aspect that distinguishes silicon photonics from others such as III-V materials and lithium niobate. However, the requirements for fabricating silicon photonic devices are quite different from those of electronic devices. Minimizing propagation losses by reducing sidewall roughness to nanometer scale over a device length of several millimeters or even centimeters has prompted researchers in academia and industry to refine the fabrication process. Chapter 3 of this thesis summarizes our efforts in fabricating silicon photonic devices using standard CMOS technology. Chapter 4 describes the characterization of nonlinear effects, including self-phase modulation (SPM), cross-phase modulation (XPM), and supercontinuum generation in silicon-wire waveguides. Silicon-wire waveguides are strip waveguides with submicron transverse dimensions, which allow strong light confinement inside the silicon core. This strong optical confinement, in addition to the large third-order nonlinear optical susceptibility of crystalline silicon, leads to a net nonlinearity which is several orders of magnitude higher than the nonlinearity of silica fiber. Significant nonlinear effects can be observed and characterized over a device length of only several millimeters in silicon wires with very small input power. These effects provide opportunities for engineers to design active silicon photonic devices which are compact and energy-efficient. Chapter 5 presents a realization of an integrated SOI optical isolator, which is a critical yet often overlooked component in photonic integrated circuits. This study shows the feasibility to make a hybrid garnet/SOI active device with very promising results. Finally, Chapter 6 summarizes our demonstration of transmitting terabit-scale data streams in silicon-wire waveguides, which is an important first-step towards enabling intra-chip interconnection networks with ultra-high bandwidths. Although the scope of this thesis is limited to providing only fractional views of the whole silicon photonics area, it provides enough references for interested readers to conduct further literature research in other aspects of silicon photonics. It is the author's hope that the thesis would convey to its readers the significance and potential of this exciting emerging technology.

From One to Many Boxes: Mobile Devices as Primary and Secondary Screens

NASA Astrophysics Data System (ADS)

Cesar, Pablo; Knoche, Hendrik; Bulterman, Dick C. A.

This chapter looks at the current changing habits on audiovisual content consumption at home, with special focus on potential uses of mobile devices. Standard television plus a remote control impose a use that is too coarse to support the various personal needs of people, while mobile devices open new possibilities from engagement and immersion into content and deliberately controlled disengagement with others to providing a screen that can be offered to include others in sharing experiences in a huddled setting.

Radio Frequency Microelectromechanical Systems [Book Chapter Manuscript

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nordquist, Christopher; Olsson, Roy H.

2014-12-15

Radio frequency microelectromechanical system (RF MEMS) devices are microscale devices that achieve superior performance relative to other technologies by taking advantage of the accuracy, precision, materials, and miniaturization available through microfabrication. To do this, these devices use their mechanical and electrical properties to perform a specific RF electrical function such as switching, transmission, or filtering. RF MEMS has been a popular area of research since the early 1990s, and within the last several years, the technology has matured sufficiently for commercialization and use in commercial market systems.

Implementation methodology for interoperable personal health devices with low-voltage low-power constraints.

PubMed

Martinez-Espronceda, Miguel; Martinez, Ignacio; Serrano, Luis; Led, Santiago; Trigo, Jesús Daniel; Marzo, Asier; Escayola, Javier; Garcia, José

2011-05-01

Traditionally, e-Health solutions were located at the point of care (PoC), while the new ubiquitous user-centered paradigm draws on standard-based personal health devices (PHDs). Such devices place strict constraints on computation and battery efficiency that encouraged the International Organization for Standardization/IEEE11073 (X73) standard for medical devices to evolve from X73PoC to X73PHD. In this context, low-voltage low-power (LV-LP) technologies meet the restrictions of X73PHD-compliant devices. Since X73PHD does not approach the software architecture, the accomplishment of an efficient design falls directly on the software developer. Therefore, computational and battery performance of such LV-LP-constrained devices can even be outperformed through an efficient X73PHD implementation design. In this context, this paper proposes a new methodology to implement X73PHD into microcontroller-based platforms with LV-LP constraints. Such implementation methodology has been developed through a patterns-based approach and applied to a number of X73PHD-compliant agents (including weighing scale, blood pressure monitor, and thermometer specializations) and microprocessor architectures (8, 16, and 32 bits) as a proof of concept. As a reference, the results obtained in the weighing scale guarantee all features of X73PHD running over a microcontroller architecture based on ARM7TDMI requiring only 168 B of RAM and 2546 B of flash memory.

Modern wireless telecommunication technologies and their electromagnetic compatibility with life-supporting equipment.

PubMed

Wallin, Mats K E B; Marve, Therese; Hakansson, Peter K

2005-11-01

Hospitals rely on pagers and ordinary telephones to reach staff members in emergency situations. New telecommunication technologies such as General Packet Radio Service (GPRS), the third generation mobile phone system Universal Mobile Telecommunications System (UMTS), and Wireless Local Area Network (WLAN) might be able to replace hospital pagers if they are electromagnetically compatible with medical devices. In this study, we sought to determine if GPRS, UMTS (Wideband Code Division Multiple Access-Frequency Division Duplex [WCDMA FDD]), and WLAN (IEEE 802.11b) transmitted signals interfere with life-supporting equipment in the intensive care and operating room environment. According to United States standard, ANSI C63.18-1997, laboratory tests were performed on 76 medical devices. In addition, clinical tests during 11 operations and 100 h of intensive care were performed. UMTS and WLAN signals caused little interference. Devices using these technologies can be used safely in critical care areas and during operations, but direct contact between medical devices and wireless communication devices ought to be avoided. In the case of GPRS, at a distance of 50 cm, it caused an older infusion pump to alarm and stop infusing; the pump had to be reset. Also, 10 cases of interference with device displays occurred. GPRS can be used safely at a distance of 1 m. Terminals/cellular phones using these technologies should be allowed without restriction in public areas because the risk of interference is minimal.

High-Bandgap Silicon Nanocrystal Solar Cells: Device Fabrication, Characterization, and Modeling

NASA Astrophysics Data System (ADS)

Löper, Philipp; Canino, Mariaconcetta; Schnabel, Manuel; Summonte, Caterina; Janz, Stefan; Zacharias, Margit

Silicon nanocrystals (Si NCs) embedded in Si-based dielectrics provide a Si-based high-bandgap material (1.7 eV) and enable the construction of crystalline Si tandem solar cells. This chapter focusses on Si NC embedded in silicon carbide, because silicon carbide offers electrical conduction through the matrix material. The material development is reviewed, and optical modeling is introduced as a powerful method to monitor the four material components, amorphous and crystalline silicon as well as amorphous and crystalline silicon carbide. In the second part of this chapter, recent device developments for the photovoltaic characterization of Si NCs are examined. The controlled growth of Si NCs involves high-temperature annealing which deteriorates the properties of any previously established selective contacts. A membrane-based device is presented to overcome these limitations. In this approach, the formation of both selective contacts is carried out after high-temperature annealing and is therefore not affected by the latter. We examine p-i-n solar cells with an intrinsic region made of Si NCs embedded in silicon carbide. Device failure due to damaged insulation layers is analyzed by light beam-induced current measurements. An optical model of the device is presented for improving the cell current. A characterization scheme for Si NC p-i-n solar cells is presented which aims at determining the fundamental transport and recombination properties, i.e., the effective mobility lifetime product, of the nanocrystal layer at device level. For this means, an illumination-dependent analysis of Si NC p-i-n solar cells is carried out within the framework of the constant field approximation. The analysis builds on an optical device model, which is used to assess the photogenerated current in each of the device layers. Illumination-dependent current-voltage curves are modelled with a voltage-dependent current collection function with only two free parameters, and excellent agreement is found between theory and experiment. An effective mobility lifetime product of 10-10 cm2/V is derived and confirmed independently from an alternative method. The procedure discussed in this chapter is proposed as a characterization scheme for further material development, providing an optimization parameter (the effective mobility lifetime product) relevant for the photovoltaic performance of Si NC films.

Risk Management Considerations for Interoperable Acquisition

DTIC Science & Technology

2006-08-01

Electronics Engineers (IEEE) to harmonize the standards for software (IEEE 12207 ) and system (IEEE 15288) life-cycle processes. A goal of this harmonization...management ( ISO /IEC 16085) is being generalized to apply to the systems level. The revised, generalized standard will add require- ments and guidance for the...risk management. The documents include the following: • ISO /IEC Guide 73: Risk Management—Vocabulary—Guidelines for use in stan- dards [ ISO 02

Should Security Researchers Experiment More and Draw More Inferences?

DTIC Science & Technology

2011-08-01

knowledge would be enormous. To obtain a large and representative sample of keystroke-dynamics research papers, we consulted the IEEE Xplore database... IEEE Xplore are similar to those published elsewhere), these confidence intervals estimate the re- gions where those true percentages would lie with 95...of articles and conference pro- ceedings published by the IEEE , to which our university maintains a subscription. We conducted two keyword searches for

Simulation Comparisons of Three Different Meander Line Dipoles

DTIC Science & Technology

2015-01-01

Paez C I. Design formulas for a meandered dipole. IEEE Xplore Digital Library, 2014: n. pag. Web. 2 September 2014. 2. Nguyen, VH, Phan, HP, Hoang...MH. Improving radiation characteristics of UHF RFID antennas by zigzag structures. IEEE Xplore Digital Library, 2014: n. pag. Web. 2 September 2014...geometry-based, frequency-independent lumped element model. IEEE Xplore Digital Library, 2014: n. pag. Web. 2 September 2014. 5. Olaode OO, Palmer WD

High Throughput via Cross-Layer Interference Alignment for Mobile Ad Hoc Networks

DTIC Science & Technology

2013-08-26

MIMO zero-forcing receiver in the presence of channel estimation error,” IEEE Transactions on Wireless Communications , vol. 6 , no. 3, pp. 805–810, Mar...Robert W. Heath, Nachiappan Valliappan. Antenna Subset Modulation for Secure Millimeter-Wave Wireless Communication , IEEE Transactions on...in MIMO Interference Alignment Networks, IEEE Transactions on Wireless Communications , (02 2012): 0. doi: 10.1109/TWC.2011.120511.111088 TOTAL: 2

Introspections on the Semantic Gap

DTIC Science & Technology

2015-04-14

cloud comput - ing. Zhang received an MS in computer science from Stony Brook University. Contact him at dozhang@ cs.stonybrook.edu. Donald E. Porter...designated by other documentation. ... 2 March/April 2015 Copublished by the IEEE Computer and Reliability Societies 1540-7993/15/$31.00 © 2015 IEEE IEEE S...pauses the VM, and the VMI tool introspects the process descriptor list. In contrast, an asynchronous mechanism would intro - spect memory

IEEE 1547 and 2030 Standards for Distributed Energy Resources Interconnection and Interoperability with the Electricity Grid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Basso, T.

Public-private partnerships have been a mainstay of the U.S. Department of Energy and the National Renewable Energy Laboratory (DOE/NREL) approach to research and development. These partnerships also include technology development that enables grid modernization and distributed energy resources (DER) advancement, especially renewable energy systems integration with the grid. Through DOE/NREL and industry support of Institute of Electrical and Electronics Engineers (IEEE) standards development, the IEEE 1547 series of standards has helped shape the way utilities and other businesses have worked together to realize increasing amounts of DER interconnected with the distribution grid. And more recently, the IEEE 2030 series ofmore » standards is helping to further realize greater implementation of communications and information technologies that provide interoperability solutions for enhanced integration of DER and loads with the grid. For these standards development partnerships, for approximately $1 of federal funding, industry partnering has contributed $5. In this report, the status update is presented for the American National Standards IEEE 1547 and IEEE 2030 series of standards. A short synopsis of the history of the 1547 standards is first presented, then the current status and future direction of the ongoing standards development activities are discussed.« less

Fast response liquid crystal devices

NASA Astrophysics Data System (ADS)

Wu, Yung-Hsun

Liquid crystal (LC) has been widely used for displays, spatial light modulators, variable optical attenuators (VOAs) and other tunable photonic devices. The response time of these devices is mainly determined by the employed liquid crystal material. The response time of a LC device depends on the visco-elastic coefficient (gamma1/K11), LC cell gap (d), and applied voltage. Hence, low visco-elastic coefficient LC materials and thinner cell gap are favorable for reducing the response time. However, low visco-elastic coefficient LCs are usually associated with a low birefringence because of shorter molecular conjugation. For display applications, such as LCD TVs, low birefringence (Deltan<0.1) LCs are commonly used. However, for optical communications at 1550 nm, low birefringence requires to a thick cell gap which, in turn, increases the response time. How to obtain fast response for the LC devices is a fundamentally important and technically challenging task. In this dissertation, we investigate several methods to improve liquid crystal response time, for examples, using dual-frequency liquid crystals, polymer stabilized liquid crystals, and sheared polymer network liquid crystals. We discover a new class of material, denoted as sheared polymer network liquid crystal (SPNLC) which exhibits a submillisecond response time. Moreover, this response time is insensitive to the LC cell gap. This is the first LC device exhibiting such an interesting property. Chapters 1 and 2 describe the motivation and background of this dissertation. From chapter 3 to chapter 6, dual-frequency liquid crystals and polymer network methods are demonstrated as examples for the variable optical attenuators. Variable optical attenuator (VOA) is a key component in optical communications. Especially, the sheared PNLC VOA shows the best result; its dynamic range reaches 43 dB while the response time is in the submillisecond range at 1550 nm wavelength, which is 50 times faster than the commercial LC-based VOA. In Chapter 7, we report a new device called axially-symmetric sheared polymer network liquid crystals (AS-SPNLC) and use it as LC devices. Through analyzing the structure of this axially-symmetric SPNLC, we construct a 3-D model to explain the observed phenomena. An axially-symmetric sheared polymer network liquid crystal has several attractive features: (1) it is polarization independent, (2) it has gradient phase change, and (3) its response time is fast. It can be used for polarization converter and divergent LC lens. In addition, a new method for simultaneously measuring the phase retardation and optic axis of a compensation film is demonstrated using an axially-symmetric sheared polymer network liquid crystal. By overlaying a tested compensation film with a calibrated SPNLC cell between crossed polarizers, the optic axis and phase retardation value of the compensation film can be determined. This simple technique can be used for simultaneously measuring the optic axis and phase retardations of both A- and C-plates. These compensation films have been used extensively in wide-view LCD industry. Therefore, this method will make an important impact to the LCD industry.

Compendium of Current Single Event Effects for Candidate Spacecraft Electronics for NASA

NASA Technical Reports Server (NTRS)

O'Bryan, Martha V.; Label, Kenneth A.; Chen, Dakai; Campola, Michael J.; Casey, Megan C.; Lauenstein, Jean-Marie; Pellish, Jonathan A.; Ladbury, Raymond L.; Berg, Melanie D.

2015-01-01

NASA spacecraft are subjected to a harsh space environment that includes exposure to various types of ionizing radiation. The performance of electronic devices in a space radiation environment are often limited by their susceptibility to single event effects (SEE). Ground-based testing is used to evaluate candidate spacecraft electronics to determine risk to spaceflight applications. Interpreting the results of radiation testing of complex devices is and adequate understanding of the test condition is critical. Studies discussed herein were undertaken to establish the application-specific sensitivities of candidate spacecraft and emerging electronic devices to single-event upset (SEU), single-event latchup (SEL), single-event gate rupture (SEGR), single-event burnout (SEB), and single-event transient (SET). For total ionizing dose (TID) and displacement damage dose (DDD) results, see a companion paper submitted to the 2015 Institute of Electrical and Electronics Engineers (IEEE) Nuclear and Space Radiation Effects Conference (NSREC) Radiation Effects Data Workshop (REDW) entitled "compendium of Current Total Ionizing Dose and Displacement Damage for Candidate Spacecraft Electronics for NASA by M. Campola, et al.

European Solid State Device Research Conference (18th) ESSDERC 88 Held In Montpellier, France on 13-16 September 1988

DTIC Science & Technology

1988-09-16

performance circuits can be expected for half-micron CMOS. References /1/ G. Baccarani and M.R. Wordeman, IEEE Trans. Electron Dev., 30, pp 1295 (1983) /2...1.6GHz universal shift register and an 8 bit DAC with a 1.2ns settling time. A micograph of the DAC is shown in figure 6. Several other pathfinder...of a divide by 8 function running at 10.7GHz ri.3 Guedl plot Of a lxSPN 2 eitterU transistor (as drawn) Fig.6 A photograph of the 8 bit DAC JOURNAL DE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Xiaohu; Shi, Di; Wang, Zhiwei

Shunt FACTS devices, such as, a Static Var Compensator (SVC), are capable of providing local reactive power compensation. They are widely used in the network to reduce the real power loss and improve the voltage profile. This paper proposes a planning model based on mixed integer conic programming (MICP) to optimally allocate SVCs in the transmission network considering load uncertainty. The load uncertainties are represented by a number of scenarios. Reformulation and linearization techniques are utilized to transform the original non-convex model into a convex second order cone programming (SOCP) model. Numerical case studies based on the IEEE 30-bus systemmore » demonstrate the effectiveness of the proposed planning model.« less

An Optimization Approach to Coexistence of Bluetooth and Wi-Fi Networks Operating in ISM Environment

NASA Astrophysics Data System (ADS)

Klajbor, Tomasz; Rak, Jacek; Wozniak, Jozef

Unlicensed ISM band is used by various wireless technologies. Therefore, issues related to ensuring the required efficiency and quality of operation of coexisting networks become essential. The paper addresses the problem of mutual interferences between IEEE 802.11b transmitters (commercially named Wi-Fi) and Bluetooth (BT) devices.An optimization approach to modeling the topology of BT scatternets is introduced, resulting in more efficient utilization of ISM environment consisting of BT and Wi-Fi networks. To achieve it, the Integer Linear Programming approach has been proposed. Example results presented in the paper illustrate significant benefits of using the proposed modeling strategy.

1989 IEEE Aerospace Applications Conference, Breckenridge, CO, Feb. 12-17, 1989, Conference Digest

NASA Astrophysics Data System (ADS)

Recent advances in electronic devices for aerospace applications are discussed in reviews and reports. Topics addressed include large-aperture mm-wave antennas, a cross-array radiometer for spacecraft applications, a technique for computing the propagation characteristics of optical fibers, an analog light-wave system for improving microwave-telemetry data communication, and a ground demonstration of an orbital-debris radar. Consideration is given to a verifiable autonomous satellite control system, Inmarsat second-generation satellites for mobile communication, automated tools for data-base design and criteria for their selection, and a desk-top simulation work station based on the DSP96002 microprocessor chip.

Final Scientific Report,

DTIC Science & Technology

1980-11-26

and J.B. Thomas, "The Effect of a Memoryless Nonlinearity on the Spectrum of a Random Process," IEEE Transactions on Information Theory, Vol. IT-23, pp...Density Function from Measurements Corrupted by Poisson Noise," IEEE Transactions on Information Theory, Vol. IT-23, pp. 764-766, November 1977. H. Derin...pp. 243-249, December 1977. G.L. Wise and N.C. Gallagher, "On Spherically Invariant Random Processes," IEEE Transactions on Information Theory, Vol. IT

Throughput and delay analysis of IEEE 802.15.6-based CSMA/CA protocol.

PubMed

Ullah, Sana; Chen, Min; Kwak, Kyung Sup

2012-12-01

The IEEE 802.15.6 is a new communication standard on Wireless Body Area Network (WBAN) that focuses on a variety of medical, Consumer Electronics (CE) and entertainment applications. In this paper, the throughput and delay performance of the IEEE 802.15.6 is presented. Numerical formulas are derived to determine the maximum throughput and minimum delay limits of the IEEE 802.15.6 for an ideal channel with no transmission errors. These limits are derived for different frequency bands and data rates. Our analysis is validated by extensive simulations using a custom C+ + simulator. Based on analytical and simulation results, useful conclusions are derived for network provisioning and packet size optimization for different applications.

Theory, modelling and calibration of passive samplers used in water monitoring: Chapter 7

USGS Publications Warehouse

Booij, K.; Vrana, B.; Huckins, James N.; Greenwood, Richard B.; Mills, Graham; Vrana, B.

2007-01-01

This chapter discusses contaminant uptake by a passive sampling device (PSD) that consists of a central sorption phase, surrounded by a membrane. A variety of models has been used over the past few years to better understand the kinetics of contaminant transfer to passive samplers. These models are essential for understanding how the amounts of absorbed contaminants relate to ambient concentrations, as well as for the design and evaluation of calibration experiments. Models differ in the number of phases and simplifying assumptions that are taken into consideration, such as the existence of (pseudo-) steady-state conditions, the presence or absence of linear concentration gradients within the membrane phase, the way in which transport within the WBL is modeled and whether or not the aqueous concentration is constant during the sampler exposure. The chapter introduces the basic concepts and models used in the literature on passive samplers for the special case of triolein-containing semipermeable membrane devices (SPMDs). These can easily be extended to samplers with more or with less sorption phases. It also discusses the transport of chemicals through the various phases constituting PSDs. the implications of these models for designing and evaluating calibration studies have been discussed.

A Comparison of RF-DNA Fingerprinting Using High/Low Value Receivers with ZigBee Devices

DTIC Science & Technology

2014-03-27

99) Device Classification using Hybrid Cross-Receiver model and USRP only testing . 54 V. Conclusion This chapter provides a summary of reseach ...Finally, when developing a Hybrid Cross-Receiver model using fingerprints from both receivers, testing with PXIe-only fingerprints proved to be the most...22 3.2 Post -Collection Processing . . . . . . . . . . . . . . . . . . . . . . . . . . 25 3.2.1 Burst Detection

Development of a mini-mobile digital radiography system by using wireless smart devices.

PubMed

Jeong, Chang-Won; Joo, Su-Chong; Ryu, Jong-Hyun; Lee, Jinseok; Kim, Kyong-Woo; Yoon, Kwon-Ha

2014-08-01

The current technologies that trend in digital radiology (DR) are toward systems using portable smart mobile as patient-centered care. We aimed to develop a mini-mobile DR system by using smart devices for wireless connection into medical information systems. We developed a mini-mobile DR system consisting of an X-ray source and a Complementary Metal-Oxide Semiconductor (CMOS) sensor based on a flat panel detector for small-field diagnostics in patients. It is used instead of the systems that are difficult to perform with a fixed traditional device. We also designed a method for embedded systems in the development of portable DR systems. The external interface used the fast and stable IEEE 802.11n wireless protocol, and we adapted the device for connections with Picture Archiving and Communication System (PACS) and smart devices. The smart device could display images on an external monitor other than the monitor in the DR system. The communication modules, main control board, and external interface supporting smart devices were implemented. Further, a smart viewer based on the external interface was developed to display image files on various smart devices. In addition, the advantage of operators is to reduce radiation dose when using remote smart devices. It is integrated with smart devices that can provide X-ray imaging services anywhere. With this technology, it can permit image observation on a smart device from a remote location by connecting to the external interface. We evaluated the response time of the mini-mobile DR system to compare to mobile PACS. The experimental results show that our system outperforms conventional mobile PACS in this regard.

Development of Novel Polymeric Materials for Gene Therapy and pH-Sensitive Drug Delivery: Modeling, Synthesis, Characterization, and Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, Brian Curtis

2002-01-01

The underlying theme of this thesis is the use of polymeric materials in bioapplications. Chapters 2-5 either develop a fundamental understanding of current materials used for bioapplications or establish protocols and procedures used in characterizing and synthesizing novel materials. In chapters 6 and 7 these principles and procedures are applied to the development of materials to be used for gene therapy and drug delivery. Chapter one is an introduction to the ideas that will be necessary to understand the subsequent chapters, as well as a literature review of these topics. Chapter two is a paper that has been published inmore » the ''Journal of Controlled Release'' that examines the mechanism of drug release from a polymer gel, as well as experimental design suggestions for the evaluation of water soluble drug delivery systems. Chapter three is a paper that has been published in the ''Journal of Pharmaceutical Sciences'' that discusses the effect ionic salts have on properties of the polymer systems examined in chapter two. Chapter four is a paper published in the Materials Research Society Fall 2000 Symposium Series dealing with the design and synthesis of a pH-sensitive polymeric drug delivery device. Chapter five is a paper that has been published in the journal ''Biomaterials'' proposing a novel polymer/metal composite for use as a biomaterial in hip arthroplasty surgery. Chapter six is a paper that will appear in an upcoming volume of the Journal ''Biomaterials'' dealing with the synthesis of a novel water soluble cationic polymer with possible applications in non-viral gene therapy. Chapter seven is a paper that has been submitted to ''Macromolecules'' discussing several novel block copolymers based on poly(ethylene glycol) and poly(diethylamino ethyl methacrylate) that possess both pH-sensitive and temperature sensitive properties. Chapter eight contains a summary of the research contained in chapters 2-7 and proposes future research for the gene therapy and drug delivery projects.« less

Ion/Ioff ratio enhancement and scalability of gate-all-around nanowire negative-capacitance FET with ferroelectric HfO2

NASA Astrophysics Data System (ADS)

Jang, Kyungmin; Saraya, Takuya; Kobayashi, Masaharu; Hiramoto, Toshiro

2017-10-01

We have investigated the energy efficiency and scalability of ferroelectric HfO2 (FE:HfO2)-based negative-capacitance field-effect-transistor (NCFET) with gate-all-around (GAA) nanowire (NW) channel structure. Analytic simulation is conducted to characterize NW-NCFET by varying NW diameter and/or thickness of gate insulator as device structural parameters. Due to the negative-capacitance effect and GAA NW channel structure, NW-NCFET is found to have 5× higher Ion/Ioff ratio than classical NW-MOSFET and 2× higher than double-gate (DG) NCFET, which results in wider design window for high Ion/Ioff ratio. To analyze these obtained results from the viewpoint of the device scalability, we have considered constraints regarding very limited device structural spaces to fit by the gate insulator and NW channel for aggresively scaled gate length (Lg) and/or very tight NW pitch. NW-NCFET still has design point with very thinned gate insulator and/or narrowed NW. Therefore, FE:HfO2-based NW-NCFET is applicable to the aggressively scaled technology node of sub-10 nm Lg and to the very tight NW integration of sub-30 nm NW pitch for beyond 7 nm technology. From 2011 to 2014, he engaged in developing high-speed optical transceiver module as an alternative military service in Republic of Korea. His research interest includes the development of steep slope MOSFETs for high energy-efficient operation and ferroelectric HfO2-based semiconductor devices, and fabrication of nanostructured devices. He joined the IBM T.J. Watson Research Center, Yorktown Heights, NY, in 2010, where he worked on advanced CMOS technologies such as FinFET, nanowire FET, SiGe channel and III-V channel. He was also engaged in launching 14 nm SOI FinFET and RMG technology development. Since 2014, he has been an Associate Professor in Institute of Industrial Science, University of Tokyo, Tokyo, Japan, where he has been working on ultralow power transistor and memory technology. Dr. Kobayashi is a member of IEEE and the Japan Society of Applied Physics. Dr. Hiramoto is a fellow of Japan Society of Applied Physics and a member of IEEE and IEICE. He served as the General Chair of Silicon Nanoelectronics Workshop in 2003 and the Program Chair in 1997, 1999, and 2001. He was on Committee of IEDM from 2003 to 2009. He was the Program Chair of Symposium on VLSI Technology in 2013 and was the General Chair in 2015. He is the Program Chair of International Conference on Solid-State Devices and Materials (SSDM) in 2016.

A field-cancellation algorithm for constructing economical planar permanent magnet (PM) multipoles with large high-quality field apertures

NASA Astrophysics Data System (ADS)

Tatchyn, Roman

1997-05-01

In recent years studies have been initiated on a new class of multipole field generators consisting of cuboid planar permanent magnet (PM) pieces arranged in bi-planar arrays of 2-fold rotational symmetry(R. Tatchyn, "Planar Permanent Magnet Multipoles: for Particle Accelerator and Storage Ring Applications ," IEEE Trans. Mag. 30, 5050(1994).)(T. Cremer, R. Tatchyn, "Planar Permanent Magnet Multipoles: Measurements and Configurations," in Proceedings of the 1995 Particle Accelerator Conference, IEEE Catalog No. 95CH35843, paper FAQ-20.). These structures, first introduced for Free Electron Laser (FEL) applications(R. Tatchyn, "Selected applications of planar permanent magnet multipoles in FEL insertion device design," NIM A341, 449(1994).), are based on reducing the rotational symmetry of conventional N-pole field generators from N-fold to 2-fold. One consequence of this reduction is a large higher-multipole content in a planar PM multipole's field at distances relatively close to the structure's axis, making it generally unsuitable for applications requiring a large high-quality field aperture. In this paper we outline an economical field-cancellation algorithm that can substantially decrease the harmonic content of a planar PM's field without breaking its biplanar geometry or 2-fold rotational symmetry. This will enable planar PM multipoles to be employed in a broader range of applications than heretofore possible, in particular as distributed focusing elements installed in insertion device gaps on synchrotron storage rings. This accomplishment is expected to remove the conventional restriction of an insertion device's length to the scale of the local focusing beta, enabling short-period, small-gap undulators to be installed and operated as high-brightness sources on lower-energy storage rings(R. Tatchyn, P. Csonka, A. Toor, "Perspectives on micropole undulators in synchrotron radiation technology," Rev. Sci. Instrum. 60(7), 1796(1989).). Operation as ordinary focusing elements in storage ring magnetic lattices, as well as the performance of other high-quality multipole applications, should also becomes possible with the realization of the proposed structures.

T-gate geometric (solution for submicrometer gate length) HEMT: Physical analysis, modeling and implementation as parasitic elements and its usage as dual gate for variable gain amplifiers

NASA Astrophysics Data System (ADS)

Gupta, Ritesh; Rathi, Servin; Kaur, Ravneet; Gupta, Mridula; Gupta, R. S.

2009-03-01

In order to achieve superior RF performance, short gate length is required for the compound semiconductor field effect transistors, but the limitation in lithography for submicrometer gate lengths leads to the formation of various metal-insulator geometries like T-gate [Sandeep R. Bahl, Jesus A. del Alamo, Physics of breakdown in InAlAs/ n +-InGaAs heterostructure field-effect transistors, IEEE Trans. Electron Devices 41 (12) (1994) 2268-2275]. These geometries are the combination of various Metal-Semiconductor (MS)/Metal-Air-Semiconductor (MAS) contacts. Moreover, field plates [S. Karmalkar, M.S. Shur, G. Simin, M. Asif Khan, Field-plate engineering for HFETs, IEEE Trans. Electron Devices 52 (2005) 2534-2540] are also being fabricated these days, mainly at the drain end ( Γ-gate) having Metal-Insulator-Semiconductor (MIS) instead of MAS contact with the intention of increasing the breakdown voltage of the device. To realize the effect of upper gate electrode in the T-gate structure and field plates, an analytical model has been proposed in the present article by dividing the whole structure into MS/MIS contact regions, applying current continuity among them and solving iteratively. The model proposed for Metal-Insulator Semiconductor High Electron Mobility Transistor (MISHEMT) [R. Gupta, S.K. Aggarwal, M. Gupta, R.S. Gupta, Analytical model for metal insulator semiconductor high electron mobility transistor (MISHEMT) for its high frequency and high power applications, J. Semicond. Technol. Sci. 6 (3) (2006) 189-198], is equally applicable to High Electron Mobility Transistors (HEMT) and has been used to formulate this model. In this paper, various structures and geometries have been compared to anticipate the need of T-gate modeling. The effect of MIS contacts has been implemented as parasitic resistance and capacitance and has also been studied to control the middle conventional gate as in dual gate technology by applying separate voltages across it. The results obtained using the proposed analytical scheme has been compared with simulated and experimental results, to prove the validity of our model.

An Improved Cross-Layering Design for IPv6 Fast Handover with IEEE 802.16m Entry Before Break Handover

NASA Astrophysics Data System (ADS)

Kim, Ronny Yongho; Jung, Inuk; Kim, Young Yong

IEEE 802.16m is an advanced air interface standard which is under development for IMT-Advanced systems, known as 4G systems. IEEE 802.16m is designed to provide a high data rate and a Quality of Service (QoS) level in order to meet user service requirements, and is especially suitable for mobilized environments. There are several factors that have great impact on such requirements. As one of the major factors, we mainly focus on latency issues. In IEEE 802.16m, an enhanced layer 2 handover scheme, described as Entry Before Break (EBB) was proposed and adopted to reduce handover latency. EBB provides significant handover interruption time reduction with respect to the legacy IEEE 802.16 handover scheme. Fast handovers for mobile IPv6 (FMIPv6) was standardized by Internet Engineering Task Force (IETF) in order to provide reduced handover interruption time from IP layer perspective. Since FMIPv6 utilizes link layer triggers to reduce handover latency, it is very critical to jointly design FMIPv6 with its underlying link layer protocol. However, FMIPv6 based on new handover scheme, EBB has not been proposed. In this paper, we propose an improved cross-layering design for FMIPv6 based on the IEEE 802.16m EBB handover. In comparison with the conventional FMIPv6 based on the legacy IEEE 802.16 network, the overall handover interruption time can be significantly reduced by employing the proposed design. Benefits of this improvement on latency reduction for mobile user applications are thoroughly investigated with both numerical analysis and simulation on various IP applications.

21 CFR 861.1 - Purpose and scope.

Code of Federal Regulations, 2010 CFR

2010-04-01

... section 514 of the Federal Food, Drug, and Cosmetic Act (the act) with respect to the establishment... controls for class II devices in § 860.7(b) of this chapter, is necessary to provide reasonable assurance...

21 CFR 861.1 - Purpose and scope.

Code of Federal Regulations, 2011 CFR

2011-04-01

... section 514 of the Federal Food, Drug, and Cosmetic Act (the act) with respect to the establishment... controls for class II devices in § 860.7(b) of this chapter, is necessary to provide reasonable assurance...

21 CFR 861.1 - Purpose and scope.

Code of Federal Regulations, 2013 CFR

2013-04-01

... section 514 of the Federal Food, Drug, and Cosmetic Act (the act) with respect to the establishment... controls for class II devices in § 860.7(b) of this chapter, is necessary to provide reasonable assurance...

21 CFR 861.1 - Purpose and scope.

Code of Federal Regulations, 2014 CFR

2014-04-01

... section 514 of the Federal Food, Drug, and Cosmetic Act (the act) with respect to the establishment... controls for class II devices in § 860.7(b) of this chapter, is necessary to provide reasonable assurance...

21 CFR 861.1 - Purpose and scope.

Code of Federal Regulations, 2012 CFR

2012-04-01

... section 514 of the Federal Food, Drug, and Cosmetic Act (the act) with respect to the establishment... controls for class II devices in § 860.7(b) of this chapter, is necessary to provide reasonable assurance...

49 CFR 385.815 - Exemption for AOBRD users.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the AOBRDs currently in its CMVs or install new devices compliance with § 395.16 of this chapter. (d... to ongoing FMCSA oversight. (e) The exemption granted under this section shall not apply to CMVs...

49 CFR 385.815 - Exemption for AOBRD users.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the AOBRDs currently in its CMVs or install new devices compliance with § 395.16 of this chapter. (d... to ongoing FMCSA oversight. (e) The exemption granted under this section shall not apply to CMVs...

27 CFR 479.23 - Restrictive use of required information.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES.... Chapter 53, or this part or section 207 of the Gun Control Act of 1968 shall be used, directly or...

27 CFR 479.192 - Commerce in firearms and ammunition.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES..., machine guns, short-barreled shotguns, or short-barreled rifles, see 18 U.S.C. Chapter 44, and Part 478 of...

27 CFR 479.192 - Commerce in firearms and ammunition.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES..., machine guns, short-barreled shotguns, or short-barreled rifles, see 18 U.S.C. Chapter 44, and Part 478 of...

27 CFR 479.192 - Commerce in firearms and ammunition.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES..., machine guns, short-barreled shotguns, or short-barreled rifles, see 18 U.S.C. Chapter 44, and Part 478 of...

27 CFR 479.192 - Commerce in firearms and ammunition.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES..., machine guns, short-barreled shotguns, or short-barreled rifles, see 18 U.S.C. Chapter 44, and Part 478 of...

27 CFR 479.192 - Commerce in firearms and ammunition.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES..., machine guns, short-barreled shotguns, or short-barreled rifles, see 18 U.S.C. Chapter 44, and Part 478 of...

27 CFR 479.23 - Restrictive use of required information.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., FIREARMS, AND EXPLOSIVES, DEPARTMENT OF JUSTICE FIREARMS AND AMMUNITION MACHINE GUNS, DESTRUCTIVE DEVICES.... Chapter 53, or this part or section 207 of the Gun Control Act of 1968 shall be used, directly or...

21 CFR 888.4800 - Template for clinical use.

Code of Federal Regulations, 2011 CFR

2011-04-01

... cutting. (b) Classification. Class I (general controls). The device is exempt from the premarket notification procedures in subpart E of part 807 of this chapter, subject to the limitations in § 888.9. [52 FR...

47 CFR 5.601 - Product development trials.

Code of Federal Regulations, 2013 CFR

2013-10-01

... participants in the experiment that the operation of the service or device is being conducted under an... chapter) or provision of services for hire is not permitted. (d) The size and scope of the experiment are...

47 CFR 5.601 - Product development trials.

Code of Federal Regulations, 2014 CFR

2014-10-01

... participants in the experiment that the operation of the service or device is being conducted under an... chapter) or provision of services for hire is not permitted. (d) The size and scope of the experiment are...

A High Performance Frequency Standard and Distribution System for Cassini Ka-Band Experiment

DTIC Science & Technology

2005-08-01

Orthogonal Polarization In Anisotropic Dielectric Resonators”, Proceedings of the 2002 IEEE International Frequency Control Symposium , pp. 553-558...2002. [9] G. J. Dick, Rabi T. Wang, Robert Tjoelker, “Design and Progress Report for Compact Cryocooled Sapphire Oscillator "VCSO"”, Proc. 2005 Joint...IEEE FCS/ PTTI. [10] R. Basu, G. J. Dick, Rabi T. Wang,” Novel Design of an All- Cryogenic RF Pound Circuit “,Proc. 2005 Joint IEEE FCS/ PTTI

Semiconductor Nanowire and Nanoribbon Thermoelectrics: A Comprehensive Computational Study

DTIC Science & Technology

2013-05-01

August 17-20, 2010). Available online through IEEE Xplore . http://dx.doi.org/10.1109/NANO.2010.5698047 4. Z. Aksamija and I. Knezevic...Korea (August 17-20, 2010). Available online through IEEE Xplore . http://dx.doi.org/10.1109/NANO.2010.5697827 5. D. Vasileska, K. Raleva, S. M...IWCE 2010) Available online through IEEE Xplore , http://dx.doi.org/10.1109/IWCE.2010.5677916 6. E. B. Ramayya and I. Knezevic, “Ultrascaled

Hierarchical Organization for Large, Dynamic Radio Networks.

DTIC Science & Technology

1988-01-01

January 1985. [3] N. Shacharm and J. Tornow . Future Directions in Packet Radio Technology. In - Proc. of IEEE INFOCOM󈨙, Washington, D.C., 1985. [4] J.J...Freeman and Company, 1979. [7] J. Jubin and J. Tornow . The DARPA Packet Radio Network Protocols. Proceed- inga of the IEEE, 75(1):21-32, January 1987... Tornow . Future Directions in Packet Radio Technology. In Proc. of IEEE INFOCOM󈨙, Washington, D.C., 1985. [28] N. Shacham and J. Westcott. Future

Watchdog Sensor Network with Multi-Stage RF Signal Identification and Cooperative Intrusion Detection

DTIC Science & Technology

2012-03-01

detection and physical layer authentication in mobile Ad Hoc networks and wireless sensor networks (WSNs) have been investigated. Résume Le rapport...IEEE 802.16 d and e (WiMAX); (b) IEEE 802.11 (Wi-Fi) family of a, b, g, n, and s (c) Sensor networks based on IEEE 802.15.4: Wireless USB, Bluetooth... sensor network are investigated for standard compatible wireless signals. The proposed signal existence detection and identification process consists

An NTP Stratum-One Server Farm Fed By IEEE-1588

DTIC Science & Technology

2010-01-01

Serial Time Code Formats,” U.S. Army White Sands Missile Range, N.M. [11] J. Eidson , 2005, “IEEE-1588 Standard for a Precision Clock Synchronization ... synchronized to its Master Clocks via IRIG-B time code on a low- frequency RF distribution system. The availability of Precise Time Protocol (PTP, IEEE...forwarding back to the requestor. The farm NTP servers are synchronized to the USNO Master Clocks using IRIG-B time code. The current standard NTP

Performance Evaluation of Glottal Inverse Filtering Algorithms Using a Physiologically Based Articulatory Speech Synthesizer

DTIC Science & Technology

2017-01-05

1 Performance Evaluation of Glottal Inverse Filtering Algorithms Using a Physiologically Based Articulatory Speech Synthesizer Yu-Ren Chien, Daryush...D. Mehta, Member, IEEE, Jón Guðnason, Matías Zañartu, Member, IEEE, and Thomas F. Quatieri, Fellow, IEEE Abstract—Glottal inverse filtering aims to...of inverse filtering performance has been challenging due to the practical difficulty in measuring the true glottal signals while speech signals are

Statistical Mechanics-Inspired Modeling of Heterogeneous Packet Transmission in Communication Networks

DTIC Science & Technology

2012-08-01

Heterogeneous Packet Transmission in Communication Networks Soumik Sarkar, Member, IEEE, Kushal Mukherjee,Member, IEEE, Asok Ray , Fellow, IEEE...Dr. Mukherjee is a member of the American Society of Mechanical Engineers. Asok Ray (SM’83–F’02) received the graduate de- grees in each discipline of...United Technologies Research Center, East Hartford, CT 06108 USA (e-mail: sarkars@utrc.utc.com; srivasa1@utrc.utc.com). K. Mukherjee and A. Ray are with

Advances in Systems and Technologies Toward Interopoerating Operational Military C2 and Simulation Systems

DTIC Science & Technology

2014-06-01

Hieb, and R. Brown, “Standardizing Battle Management Language – A Vital Move Towards the Army Transformation,” paper 01S- SIW -067, IEEE Fall Simulation...Hieb, M., W. Sudnikovich, A. Tolk and J. Pullen, “Developing Battle Management Language into a Web Service,” paper 04S- SIW -113, IEEE Spring Simulation...Mediation and Data Storage,” paper 05S- SIW -019, IEEE Spring Simulation Interoperability Workshop, Orlando, FL, 2005 [6] Multilateral

Algorithm XXX : functions to support the IEEE standard for binary floating-point arithmetic.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cody, W. J.; Mathematics and Computer Science

1993-12-01

This paper describes C programs for the support functions copysign(x,y), logb(x), scalb(x,n), nextafter(x,y), finite(x), and isnan(x) recommended in the Appendix to the IEEE Standard for Binary Floating-Point Arithmetic. In the case of logb, the modified definition given in the later IEEE Standard for Radix-Independent Floating-Point Arithmetic is followed. These programs should run without modification on most systems conforming to the binary standard.

Integrated Mission Simulation (IMSim): Multiphase Initialization Design with Late Joiners, Rejoiners and Federation Save & Restore

NASA Technical Reports Server (NTRS)

Dexter, Daniel E.; Varesic, Tony E.

2015-01-01

This document describes the design of the Integrated Mission Simulation (IMSim) federate multiphase initialization process. The main goal of multiphase initialization is to allow for data interdependencies during the federate initialization process. IMSim uses the High Level Architecture (HLA) IEEE 1516 [1] to provide the communication and coordination between the distributed parts of the simulation. They are implemented using the Runtime Infrastructure (RTI) from Pitch Technologies AB. This document assumes a basic understanding of IEEE 1516 HLA, and C++ programming. In addition, there are several subtle points in working with IEEE 1516 and the Pitch RTI that need to be understood, which are covered in Appendix A. Please note the C++ code samples shown in this document are for the IEEE 1516-2000 standard.

Implicit Block ACK Scheme for IEEE 802.11 WLANs

PubMed Central

Sthapit, Pranesh; Pyun, Jae-Young

2016-01-01

The throughput of IEEE 802.11 standard is significantly bounded by the associated Medium Access Control (MAC) overhead. Because of the overhead, an upper limit exists for throughput, which is bounded, including situations where data rates are extremely high. Therefore, an overhead reduction is necessary to achieve higher throughput. The IEEE 802.11e amendment introduced the block ACK mechanism, to reduce the number of control messages in MAC. Although the block ACK scheme greatly reduces overhead, further improvements are possible. In this letter, we propose an implicit block ACK method that further reduces the overhead associated with IEEE 802.11e’s block ACK scheme. The mathematical analysis results are presented for both the original protocol and the proposed scheme. A performance improvement of greater than 10% was achieved with the proposed implementation.

Real-Time Station Grouping under Dynamic Traffic for IEEE 802.11ah

PubMed Central

Tian, Le; Latré, Steven

2017-01-01

IEEE 802.11ah, marketed as Wi-Fi HaLow, extends Wi-Fi to the sub-1 GHz spectrum. Through a number of physical layer (PHY) and media access control (MAC) optimizations, it aims to bring greatly increased range, energy-efficiency, and scalability. This makes 802.11ah the perfect candidate for providing connectivity to Internet of Things (IoT) devices. One of these new features, referred to as the Restricted Access Window (RAW), focuses on improving scalability in highly dense deployments. RAW divides stations into groups and reduces contention and collisions by only allowing channel access to one group at a time. However, the standard does not dictate how to determine the optimal RAW grouping parameters. The optimal parameters depend on the current network conditions, and it has been shown that incorrect configuration severely impacts throughput, latency and energy efficiency. In this paper, we propose a traffic-adaptive RAW optimization algorithm (TAROA) to adapt the RAW parameters in real time based on the current traffic conditions, optimized for sensor networks in which each sensor transmits packets with a certain (predictable) frequency and may change the transmission frequency over time. The TAROA algorithm is executed at each target beacon transmission time (TBTT), and it first estimates the packet transmission interval of each station only based on packet transmission information obtained by access point (AP) during the last beacon interval. Then, TAROA determines the RAW parameters and assigns stations to RAW slots based on this estimated transmission frequency. The simulation results show that, compared to enhanced distributed channel access/distributed coordination function (EDCA/DCF), the TAROA algorithm can highly improve the performance of IEEE 802.11ah dense networks in terms of throughput, especially when hidden nodes exist, although it does not always achieve better latency performance. This paper contributes with a practical approach to optimizing RAW grouping under dynamic traffic in real time, which is a major leap towards applying RAW mechanism in real-life IoT networks. PMID:28677617

Real-Time Station Grouping under Dynamic Traffic for IEEE 802.11ah.

PubMed

Tian, Le; Khorov, Evgeny; Latré, Steven; Famaey, Jeroen

2017-07-04

IEEE 802.11ah, marketed as Wi-Fi HaLow, extends Wi-Fi to the sub-1 GHz spectrum. Through a number of physical layer (PHY) and media access control (MAC) optimizations, it aims to bring greatly increased range, energy-efficiency, and scalability. This makes 802.11ah the perfect candidate for providing connectivity to Internet of Things (IoT) devices. One of these new features, referred to as the Restricted Access Window (RAW), focuses on improving scalability in highly dense deployments. RAW divides stations into groups and reduces contention and collisions by only allowing channel access to one group at a time. However, the standard does not dictate how to determine the optimal RAW grouping parameters. The optimal parameters depend on the current network conditions, and it has been shown that incorrect configuration severely impacts throughput, latency and energy efficiency. In this paper, we propose a traffic-adaptive RAW optimization algorithm (TAROA) to adapt the RAW parameters in real time based on the current traffic conditions, optimized for sensor networks in which each sensor transmits packets with a certain (predictable) frequency and may change the transmission frequency over time. The TAROA algorithm is executed at each target beacon transmission time (TBTT), and it first estimates the packet transmission interval of each station only based on packet transmission information obtained by access point (AP) during the last beacon interval. Then, TAROA determines the RAW parameters and assigns stations to RAW slots based on this estimated transmission frequency. The simulation results show that, compared to enhanced distributed channel access/distributed coordination function (EDCA/DCF), the TAROA algorithm can highly improve the performance of IEEE 802.11ah dense networks in terms of throughput, especially when hidden nodes exist, although it does not always achieve better latency performance. This paper contributes with a practical approach to optimizing RAW grouping under dynamic traffic in real time, which is a major leap towards applying RAW mechanism in real-life IoT networks.

Vehicular-networking- and road-weather-related research in Sodankylä

NASA Astrophysics Data System (ADS)

Sukuvaara, Timo; Mäenpää, Kari; Ylitalo, Riika

2016-10-01

Vehicular-networking- and especially safety-related wireless vehicular services have been under intensive research for almost a decade now. Only in recent years has road weather information also been acknowledged to play an important role when aiming to reduce traffic accidents and fatalities via intelligent transport systems (ITSs). Part of the progress can be seen as a result of the Finnish Meteorological Institute's (FMI) long-term research work in Sodankylä within the topic, originally started in 2006. Within multiple research projects, the FMI Arctic Research Centre has been developing wireless vehicular networking and road weather services, in co-operation with the FMI meteorological services team in Helsinki. At the beginning the wireless communication was conducted with traditional Wi-Fi type local area networking, but during the development the system has evolved into a hybrid communication system of a combined vehicular ad hoc networking (VANET) system with special IEEE 802.11p protocol and supporting cellular networking based on a commercial 3G network, not forgetting support for Wi-Fi-based devices also. For piloting purposes and further research, we have established a special combined road weather station (RWS) and roadside unit (RSU), to interact with vehicles as a service hotspot. In the RWS-RSU we have chosen to build support to all major approaches, IEEE 802.11, traditional Wi-Fi and cellular 3G. We employ road weather systems of FMI, along with RWS and vehicle data gathered from vehicles, in the up-to-date localized weather data delivered in real time. IEEE 802.11p vehicular networking is supported with Wi-Fi and 3G communications. This paper briefly introduces the research work related to vehicular networking and road weather services conducted in Sodankylä, as well as the research project involved in this work. The current status of instrumentation, available services and capabilities are presented in order to formulate a clear general view of the research field.

Electrical Characterization of Semiconductor Materials and Devices

NASA Astrophysics Data System (ADS)

Deen, M.; Pascal, Fabien

Semiconductor materials and devices continue to occupy a preeminent technological position due to their importance when building integrated electronic systems used in a wide range of applications from computers, cell-phones, personal digital assistants, digital cameras and electronic entertainment systems, to electronic instrumentation for medical diagnositics and environmental monitoring. Key ingredients of this technological dominance have been the rapid advances made in the quality and processing of materials - semiconductors, conductors and dielectrics - which have given metal oxide semiconductor device technology its important characteristics of negligible standby power dissipation, good input-output isolation, surface potential control and reliable operation. However, when assessing material quality and device reliability, it is important to have fast, nondestructive, accurate and easy-to-use electrical characterization techniques available, so that important parameters such as carrier doping density, type and mobility of carriers, interface quality, oxide trap density, semiconductor bulk defect density, contact and other parasitic resistances and oxide electrical integrity can be determined. This chapter describes some of the more widely employed and popular techniques that are used to determine these important parameters. The techniques presented in this chapter range in both complexity and test structure requirements from simple current-voltage measurements to more sophisticated low-frequency noise, charge pumping and deep-level transient spectroscopy techniques.

Specialty Engineering Supplement to IEEE-15288.1

DTIC Science & Technology

2015-05-15

receiver required to work in a dense EMI environment. (15) Any RF receiver with a burnout level of less than 30 dBm (1 mW). b. A summary of all...Context 2.1 ISO-IEC-IEEE-15288: 2015, Systems and Software Engineering — System life cycle processes ISO-IEC-IEEE 15288 is the DOD-adopted standard for...to ISO-15288 for application of systems engineering on defense programs that was developed by a joint services working group under the auspices of the

Radar Methods in Urban Environments

DTIC Science & Technology

2016-10-26

to appear in IEEE Journal of Selected Topics in Signal Processing. J8. M. Wang and A. Nehorai, “Coarrays, MUSIC , and the Cramér Rao bound,” to...Journal Papers: 1. P. Chavali and A. Nehorai, "Scheduling and resource allocation in a cognitive radar network for multiple- target tracking,’’ IEEE...Processing. 33. M. Wang and A. Nehorai, "Coarrays, MUSIC , and the Cramér Rao bound," to appear in IEEE Trans. on Signal Processing. 34. J. Li and A. Nehorai

Estimating Ergodic Capacity of Cooperative Analog Relaying under Different Adaptive Source Transmission Techniques

DTIC Science & Technology

2011-08-01

component in an airborne platform. Authorized licensed use limited to: ROME AFB. Downloaded on August 05,2010 at 14:47:37 UTC from IEEE Xplore ...UTC from IEEE Xplore . Restrictions apply. 2 . (7) For instance, it is not difficult to show that the MGF of for Nakagami-m fading with i.n.d fading...August 05,2010 at 14:47:37 UTC from IEEE Xplore . Restrictions apply. 3 ditions. Once again, using integration by parts, (14) can be concisely expressed

Unlocking User-Centered Design Methods for Building Cyber Security Visualizations

DTIC Science & Technology

2015-10-03

a final, deployed tool. Goodall et al. interviewed analysts to derive requirements for a network security tool [14], while Stoll et al. explain the...4673-7599-3/15/$31.00 c©2015 IEEE 2015 IEEE SYMPOSIUM ON VISUALIZATION FOR CYBER SECURITY (VIZSEC) [14] J. R. Goodall , A. A. Ozok, W. G. Lutters, P...Visualization for Cyber Security, pages 91–98. IEEE, 2005. [19] A. Komlodi, P. Rheingans, U. Ayachit, J. Goodall , and A. Joshi. A user- centered look at

IEEE International Symposium Information Theory, held at Santa Monica California, February 9-12, 1981.

DTIC Science & Technology

1981-01-01

Channel and study permutation codes as a special case. ,uch a code is generated by an initial vector x, a group G of orthogonal n by n matrices, and a...random-access components, is introduced and studied . Under this scheme, the network stations are divided into groups , each of which is assigned a...IEEE INFORMATION THEORY GROUP CO-SPONSORED BY: UNION RADIO SCIENTIFIQUE INTERNATIONALE IEEE Catalog Number 81 CH 1609-7 IT 𔃻. 81 ~20 04Q SECURITY

Performance Evaluation of Parallel Algorithms and Architectures in Concurrent Multiprocessor Systems

DTIC Science & Technology

1988-09-01

HEP and Other Parallel processors, Report no. ANL-83-97, Argonne National Laboratory, Argonne, Ill. 1983. [19] Davidson, G . S. A Practical Paradigm for...IEEE Comp. Soc., 1986. [241 Peir, Jih-kwon, and D. Gajski , "CAMP: A Programming Aide For Multiprocessors," Proc. 1986 ICPP, IEEE Comp. Soc., pp475...482. [251 Pfister, G . F., and V. A. Norton, "Hot Spot Contention and Combining in Multistage Interconnection Networks,"IEEE Trans. Comp., C-34, Oct

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

IRIG 106 Chapter 10 Programmers Handbook

DTIC Science & Technology

2016-08-16

card number that controls the desired SCSI device. When 10 Internet Engineering Task Force...idmptmat - Read and dump a TMATS record from an IRIG 106 Ch 10 data file Copyright (c) 2006 Irig106.org All rights reserved

Wind Tunnel Model and Test to Evaluate the Effectiveness of a Passive Gust Alleviation Device for a Flying Wing Aircraft

DTIC Science & Technology

2016-10-04

model of 1.24 m with the PGAD and control surface 3 1.2. Design and manufacture of the gust generator (frame, blades , actuation and control system...Chapter 3, a gust generator with two rotating blades was designed and manufactured to induce a transverse turbulence for wind tunnel test. A CFD...velocity at 8C (eight times of blade chord length) achieved 1.3%. In Chapter 4, the wind tunnel test of the scaled wing model is presented, including the

Electromagnetic immunity of implantable pacemakers exposed to wi-fi devices.

PubMed

Mattei, Eugenio; Censi, Federica; Triventi, Michele; Calcagnini, Giovanni

2014-10-01

The purpose of this study is to evaluate the potential for electromagnetic interference (EMI) and to assess the immunity level of implantable pacemakers (PM) when exposed to the radiofrequency (RF) field generated by Wi-Fi devices. Ten PM from five manufacturers, representative of what today is implanted in patients, have been tested in vitro and exposed to the signal generated by a Wi-Fi transmitter. An exposure setup that reproduces the actual IEEE 802.11b/g protocol has been designed and used during the tests. The system is able to amplify the Wi-Fi signal and transmits at power levels higher than those allowed by current international regulation. Such approach allows one to obtain, in case of no EMI, a safety margin for PM exposed to Wi-Fi signals, which otherwise cannot be derived if using commercial Wi-Fi equipment. The results of this study mitigate concerns about using Wi-Fi devices close to PM: none of the PM tested exhibit any degradation of their performance, even when exposed to RF field levels five times higher than those allowed by current international regulation (20 W EIRP). In conclusion, Wi-Fi devices do not pose risks of EMI to implantable PM. The immunity level of modern PM is much higher than the transmitting power of RF devices operating at 2.4 GHz.

Technical Division | Fermilab

Science.gov Websites

Martinello wins 2018 IEEE PAST Doctoral Student Award November 28, 2017 PAST has awarded Fermilab scientist Martina Martinello the 2018 IEEE PAST Doctoral Student Award. Performance recognition awards go to

Optical devices for biochemical sensing in flame hydrolysis deposited glass

NASA Astrophysics Data System (ADS)

Ruano-Lopez, Jesus M.

Previous research in the field of Flame Hydrolysis Deposition (FHD) of glasses has focused on the production of low cost optical devices for the field of telecommunications. The originality of this doctoral research resides in the exploration of this technology in the fabrication of optical bio-chemical sensors, with integrated "Lab-on-a-chip" devices. To achieve this goal, we have combined and applied different microfabrication processes for the manufacture of sensor platforms using FHD. These structures are unique in that they take advantage of the intrinsic benefits of the microfabrication process, such as, miniaturisation and mass production, and combine them with the properties of FHD glass, namely: low loss optical transducing mechanisms, planar technologies and monolithic integration. This thesis demonstrates that FHD is a suitable technology for biosensing and Lab- on-a-Chip applications. The objective is to provide future researchers with the necessary tools to accomplish an integrated analytical system based on FHD. We have designed, fabricated, and successfully tested a FHD miniaturised sensor, which comprised optical and microfluidic circuitry, in the framework of low volume fluorescence assays. For the first time, volumes as low as 570 pL were analysed with a Cyanine-5 fluorophore with a detection limit of 20 pM, or ca. 6000 molecules (+/-3sigma) for this platform. The fabrication of the sensor generated a compilation of processes that were then utilised to produce other possible optical platforms for bio-chemical sensors in FHD, e.g. arrays and microfluidics. The "catalogue" of methods used included new recipes for reactive ion etching, glass deposition and bonding techniques that enabled the development of the microfluidic circuitry, integrated with an optical circuitry. Furthermore, we developed techniques to implement new tasks such as optical signal treatment using integrated optical structures, planar arraying of sensors, a separating element for liquid chromatography, and finally a pumping system for delivering small amounts of liquid along the microfluidic channels. This thesis comprises six chapters. In Chapter 1, an overview of the topic was presented, offering a review of the various fields addressed, as well as a description of the motivation and originality of this work. Chapter 2 describes the processes developed to fabricate an optical sensor, and Chapter 3 assesses its performance. In Chapter 4, integrated optical circuit designs and their fabrication methods, as well as developing and testing of an array of sensors, are presented. The description of a separating element involved in a liquid chromatography system, and the pumping of liquids in a FHD optical device, were addressed in Chapter 5. Finally, Chapter 6 summarised the conclusions and suggested possible future work. Last but not least, the appendix, contains techniques for hybrid integration; recipes for etching of rare earth glasses; as well as instrumentation designs. This research has taken Flame Hydrolysis Deposition technique into the world of optical bio-chemical sensors, creating a bridge between analytical assays and FHD glass. In this respect, the demonstrated flexibility of the technology will enable a variety of configurations to be created and implemented, with the prospect of using the techniques for laboratory-on-a-chip technologies. The work has been patented by the University of Glasgow, for future exploitation in analytical biotechnology and Lab-on-a-Chip.