1.6μm DIAL System for Measurements of CO2 Concentration Profiles in the Atmosphere

NASA Astrophysics Data System (ADS)

Nagasawa, C.; Abo, M.; Shibata, Y.

2013-12-01

We have developed a direct detection 1.6 μm differential absorption lidar (DIAL) technique to perform range-resolved measurements of vertical CO2 concentration profiles in the atmosphere. Our 1.6 μm DIAL system has a 60 cm telescope for vertical measurement and a 25 cm scanning telescope for horizontal measurement. This 1.6 μm DIAL system is also available to measure CO2 concentration profiles for daytime by using narrow-band interference filters. The 1.6 μm DIAL measurement was achieved successfully the vertical CO2 profile up to 7 km altitude with an error less than 1.0 % by integration time of 30 minutes and vertical resolution of 300 - 600 m. The CO2 DIAL was also operated with the range-height indicator (RHI) mode, and the 2-D measurement provided inhomogeneity in the boundary layer. The vertical distribution of CO2 concentration from 2 km to 7 km altitude has been observed using two telescopes with different apertures. We hope to get the data of the CO2 concentration from lower altitude to 7 km at the same time. Since the change of signal intensity is larger near the ground, it is also important to the install the photon counter with the faster count rate to expand the dynamic range. The high speed counter and the telescope system make the dynamic range expand more than 10 times and the vertical distribution observation of CO2 concentration from 0.5 km to 7 km altitude is performed. This work was financially supported by the System Development Program for Advanced Measurement and Analysis of the Japan Science and Technology Agency. References Sakaizawa, D., C. Nagasawa, T. Nagai, M. Abo, Y. Shibata, H. Nagai, M. Nakazato, and T. Sakai, Development of a 1.6μm differential absorption lidar with a quasi-phase-matching optical parametric oscillator and photon-counting detector for the vertical CO2 profile, Applied Optics, Vol.48, No.4, pp. 748-757, 2009. Stephens, B. B. et al., Weak Northern and Strong Tropical Land Carbon Uptake from Vertical Profiles of Atmospheric CO2, Science 316, pp. 1732-1735, 2007.

Airborne water vapor DIAL system and measurements of water and aerosol profiles

NASA Technical Reports Server (NTRS)

Higdon, Noah S.; Browell, Edward V.

1991-01-01

The Lidar Applications Group at NASA Langley Research Center has developed a differential absorption lidar (DIAL) system for the remote measurement of atmospheric water vapor (H2O) and aerosols from an aircraft. The airborne H2O DIAL system is designed for extended flights to perform mesoscale investigations of H2O and aerosol distributions. This DIAL system utilizes a Nd:YAG-laser-pumped dye laser as the off-line transmitter and a narrowband, tunable Alexandrite laser as the on-line transmitter. The dye laser has an oscillator/amplifier configuration which incorporates a grating and prism in the oscillator cavity to narrow the output linewidth to approximately 15 pm. This linewidth can be maintained over the wavelength range of 725 to 730 nm, and it is sufficiently narrow to satisfy the off-line spectral requirements. In the Alexandrite laser, three intracavity tuning elements combine to produce an output linewidth of 1.1 pm. These spectral devices include a five-plate birefringent tuner, a 1-mm thick solid etalon and a 1-cm air-spaced etalon. A wavelength stability of +/- 0.35 pm is achieved by active feedback control of the two Fabry-Perot etalons using a frequency stabilized He-Ne laser as a wavelength reference. The three tuning elements can be synchronously scanned over a 150 pm range with microprocessor-based scanning electronics. Other aspects of the DIAL system are discussed.

NASA three-laser airborne differential absorption lidar system electronics

NASA Technical Reports Server (NTRS)

Allen, R. J.; Copeland, G. D.

1984-01-01

The system control and signal conditioning electronics of the NASA three laser airborne differential absorption lidar (DIAL) system are described. The multipurpose DIAL system was developed for the remote measurement of gas and aerosol profiles in the troposphere and lower stratosphere. A brief description and photographs of the majority of electronics units developed under this contract are presented. The precision control system; which includes a master control unit, three combined NASA laser control interface/quantel control units, and three noise pulse discriminator/pockels cell pulser units; is described in detail. The need and design considerations for precision timing and control are discussed. Calibration procedures are included.

Development of a high-speed wavelength-agile CO2 local oscillator for heterodyne DIAL measurements

NASA Astrophysics Data System (ADS)

Senft, Daniel C.; Pierrottet, Diego F.

2002-06-01

A high repetition rate, wavelength agile CO2 laser has been developed at the Air Force Research Laboratory for use as a local oscillator in a heterodyne detection receiver. Fats wavelength selection is required for measurements of airborne chemical vapors using the differential absorption lidar (DIAL) technique. Acousto-optic modulator are used to tune between different wavelengths at high speeds without the need for moving mechanical parts. Other advantages obtained by the use of acousto-optic modulators are laser output power control per wavelength and rugged packaging for field applications. The local oscillator design is described, and the results from laboratory DIAL measurements are presented. The coherent remote optical sensor system is an internal research project being conducted by the Air Force Research Laboratory Directed Energy Directorate, Active Remote Sensing Branch. The objective of the project is to develop a new long-range standoff spectral sensor that takes advantage of the enhanced performance capabilities coherent detection can provide. Emphasis of the development is on a low cost, compact, and rugged active sensor exclusively designed for heterodyne detection using the differential absorption lidar technique. State of the art technologies in waveguide laser construction and acousto- optics make feasible the next generation of lasers capable of supporting coherent lidar system requirements. Issues addressed as part of the development include optoelectronic engineering of a low cost rugged system, and fast data throughput for real time chemical concentration measurements. All hardware used in this sensor are off-the- shelf items, so only minor hardware modifications were required for the system as it stands. This paper describes a high-speed heterodyne detection CO2 DIAL system that employs a wavelength agile, acousto-optically tuned local oscillator in the receiver. Sample experimental data collected in a controlled environment are presented as well. Chemical detection using 12 wavelengths at 200 pulses per second has been demonstrated. Initial progress on experiments to make a direct, simultaneous comparison of heterodyne and direct detection DIAL systems will also be described.

Performance evaluation of a 1.6-µm methane DIAL system from ground, aircraft and UAV platforms.

PubMed

Refaat, Tamer F; Ismail, Syed; Nehrir, Amin R; Hair, John W; Crawford, James H; Leifer, Ira; Shuman, Timothy

2013-12-16

Methane is an efficient absorber of infrared radiation and a potent greenhouse gas with a warming potential 72 times greater than carbon dioxide on a per molecule basis. Development of methane active remote sensing capability using the differential absorption lidar (DIAL) technique enables scientific assessments of the gas emission and impacts on the climate. A performance evaluation of a pulsed DIAL system for monitoring atmospheric methane is presented. This system leverages a robust injection-seeded pulsed Nd:YAG pumped Optical Parametric Oscillator (OPO) laser technology operating in the 1.645 µm spectral band. The system also leverages an efficient low noise, commercially available, InGaAs avalanche photo-detector (APD). Lidar signals and error budget are analyzed for system operation on ground in the range-resolved DIAL mode and from airborne platforms in the integrated path DIAL (IPDA) mode. Results indicate system capability of measuring methane concentration profiles with <1.0% total error up to 4.5 km range with 5 minute averaging from ground. For airborne IPDA, the total error in the column dry mixing ratio is less than 0.3% with 0.1 sec average using ground returns. This system has a unique capability of combining signals from the atmospheric scattering from layers above the surface with ground return signals, which provides methane column measurement between the atmospheric scattering layer and the ground directly. In such case 0.5% and 1.2% total errors are achieved with 10 sec average from airborne platforms at 8 km and 15.24 km altitudes, respectively. Due to the pulsed nature of the transmitter, the system is relatively insensitive to aerosol and cloud interferences. Such DIAL system would be ideal for investigating high latitude methane releases over polar ice sheets, permafrost regions, wetlands, and over ocean during day and night. This system would have commercial potential for fossil fuel leaks detection and industrial monitoring applications.

Flight test results for the Digital Integrated Automatic Landing Systems (DIALS): A modern control full-state feedback design

NASA Technical Reports Server (NTRS)

Hueschen, R. M.

1984-01-01

The Digital Integrated Automatic Landing System (DIALS) is discussed. The DIALS is a modern control theory design performing all the maneuver modes associated with current autoland systems: localizer capture and track, glideslope capture and track, decrab, and flare. The DIALS is an integrated full-state feedback system which was designed using direct-digital methods. The DIALS uses standard aircraft sensors and the digital Microwave Landing System (MLS) signals as measurements. It consists of separately designed longitudinal and lateral channels although some cross-coupling variables are fed between channels for improved state estimates and trajectory commands. The DIALS was implemented within the 16-bit fixed-point flight computers of the ATOPS research aircraft, a small twin jet commercial transport outfitted with a second research cockpit and a fly-by-wire system. The DIALS became the first modern control theory design to be successfully flight tested on a commercial-type aircraft. Flight tests were conducted in late 1981 using a wide coverage MLS on Runway 22 at Wallops Flight Center. All the modes were exercised including the capture and track of steep glidescopes up to 5 degrees.

A mobile phone-based Communication Support System for elderly persons.

PubMed

Ogawa, Hidekuni; Yonezawa, Yoshiharu; Maki, Hiromichi; Caldwell, W Morton

2007-01-01

A mobile phone-based communication support system has been developed for assisting elderly people to communicate by mobile phone. The system consists of a low power mobile phone (PHS phone) having a large liquid crystal screen. When an elderly person telephones, they then choose a communication person from registered support personnel pictures displayed on the liquid crystal screen. The PHS phone dials that person automatically. The elderly person can therefore easily recognize and verify the person. The newly-developed communication support system assists a significant percentage of elderly people with poor eyesight and memory, which frequently cause communication problems, such as dialing a wrong number.

The portable P300 dialing system based on tablet and Emotiv Epoc headset.

PubMed

Tong Jijun; Zhang Peng; Xiao Ran; Ding Lei

2015-08-01

A Brain-computer interface (BCI) is a novel communication system that translates brain signals into a control signal. Now with the appearance of the commercial EEG headsets and mobile smart platforms (tablet, smartphone), it is possible to develop the mobile BCI system, which can greatly improve the life quality of patients suffering from motor disease, such as amyotrophic lateral scleroses (ALS), multiple sclerosis, cerebral palsy and head trauma. This study adopted a 14-channel Emotiv EPOC headset and Microsoft surface pro 3 to realize a dialing system, which was represented by 4×3 matrices of alphanumeric characters. The performance of the online portable dialing system based on P300 is satisfying. The average classification accuracy reaches 88.75±10.57% in lab and 73.75±16.94% in metro, while the information transfer rate (ITR) reaches 7.17±1.80 and 5.05±2.17 bits/min respectively. This means the commercial EEG headset and tablet has good prospect in developing real time BCI system in realistic environments.

Opo lidar sounding of trace atmospheric gases in the 3 - 4 μm spectral range

NASA Astrophysics Data System (ADS)

Romanovskii, Oleg A.; Sadovnikov, Sergey A.; Kharchenko, Olga V.; Yakovlev, Semen V.

2018-04-01

The applicability of a KTA crystal-based laser system with optical parametric oscillators (OPO) generation to lidar sounding of the atmosphere in the spectral range 3-4 μm is studied in this work. A technique developed for lidar sounding of trace atmospheric gases (TAG) is based on differential absorption lidar (DIAL) method and differential optical absorption spectroscopy (DOAS). The DIAL-DOAS technique is tested to estimate its efficiency for lidar sounding of atmospheric trace gases. The numerical simulation performed shows that a KTA-based OPO laser is a promising source of radiation for remote DIAL-DOAS sounding of the TAGs under study along surface tropospheric paths. A possibility of using a PD38-03-PR photodiode for the DIAL gas analysis of the atmosphere is shown.

Flight tests of a range-resolved airborne dial with two min-tea CO2 lasers

NASA Technical Reports Server (NTRS)

Itabe, T.; Ishizu, M.; Aruga, T.; Igarashi, T.; Asai, K.

1986-01-01

It is important to measure regional distributions of ozone concentrations in a short time for understanding a mechanism of photo-chemical smog development. An airborne Differential Absorption Lidar (DIAL) system with two low-power mini-TEA CO2 lasers was developed for measuring three-dimensional distributions of ozone in the lower troposphere. The CO2 DIAL is a nadir-looking system and is designed to measure ozone profiles between ground and airplane by using atmospheric aerosols as a distributed radar target. First flight test with a single laser were conducted in February 1985 over the Tokyo area. The system was operated at an altitude of 5000 ft. Results of the first flight tests show that the height profiles of the received power in the boundary layer were different between over land and ocean. The received power has to be inverted to an expression of a single optical parameter to see real aerosol distributions. Inversion of the lidar signal to the aerosol extinction was performed by using Klett's solution.

Design and development of a compact lidar/DIAL system for aerial surveillance of urban areas

NASA Astrophysics Data System (ADS)

Gaudio, P.; Gelfusa, M.; Malizia, A.; Richetta, M.; Antonucci, A.; Ventura, P.; Murari, A.; Vega, J.

2013-10-01

Recently surveying large areas in an automatic way, for early detection of harmful chemical agents, has become a strategic objective of defence and public health organisations. The Lidar-Dial techniques are widely recognized as a cost-effective alternative to monitor large portions of the atmosphere but, up to now, they have been mainly deployed as ground based stations. The design reported in this paper concerns the development of a Lidar-Dial system compact enough to be carried by a small airplane and capable of detecting sudden releases in air of harmful and/or polluting substances. The proposed approach consists of continuous monitoring of the area under surveillance with a Lidar type measurement. Once a significant increase in the density of backscattering substances is revealed, it is intended to switch to the Dial technique to identify the released chemicals and to determine its concentration. In this paper, the design of the proposed system is described and the simulations carried out to determine its performances are reported. For the Lidar measurements, commercially available Nd- YAG laser sources have already been tested and their performances, in combination with avalanche photodiodes, have been experimentally verified to meet the required specifications. With regard to the DIAL measurements, new compact CO2 laser sources are being investigated. The most promising candidate presents an energy per pulse of about 50 mJ typical, sufficient for a range of at least 500m. The laser also provides the so called "agile tuning" option that allows to quickly tune the wavelength. To guarantee continuous, automatic surveying of large areas, innovative solutions are required for the data acquisition, self monitoring of the system and data analysis. The results of the design, the simulations and some preliminary tests illustrate the potential of the chosen, integrated approach.

DialBetics: A Novel Smartphone-based Self-management Support System for Type 2 Diabetes Patients.

PubMed

Waki, Kayo; Fujita, Hideo; Uchimura, Yuji; Omae, Koji; Aramaki, Eiji; Kato, Shigeko; Lee, Hanae; Kobayashi, Haruka; Kadowaki, Takashi; Ohe, Kazuhiko

2014-03-01

Numerous diabetes-management systems and programs for improving glycemic control to meet guideline targets have been proposed, using IT technology. But all of them allow only limited-or no-real-time interaction between patients and the system in terms of system response to patient input; few studies have effectively assessed the systems' usability and feasibility to determine how well patients understand and can adopt the technology involved. DialBetics is composed of 4 modules: (1) data transmission module, (2) evaluation module, (3) communication module, and (4) dietary evaluation module. A 3-month randomized study was designed to assess the safety and usability of a remote health-data monitoring system, and especially its impact on modifying patient lifestyles to improve diabetes self-management and, thus, clinical outcomes. Fifty-four type 2 diabetes patients were randomly divided into 2 groups, 27 in the DialBetics group and 27 in the non-DialBetics control group. HbA1c and fasting blood sugar (FBS) values declined significantly in the DialBetics group: HbA1c decreased an average of 0.4% (from 7.1 ± 1.0% to 6.7 ± 0.7%) compared with an average increase of 0.1% in the non-DialBetics group (from 7.0 ± 0.9% to 7.1 ± 1.1%) (P = .015); The DialBetics group FBS decreased an average of 5.5 mg/dl compared with a non-DialBetics group average increase of 16.9 mg/dl (P = .019). BMI improvement-although not statistically significant because of the small sample size-was greater in the DialBetics group. DialBetics was shown to be a feasible and an effective tool for improving HbA1c by providing patients with real-time support based on their measurements and inputs. © 2014 Diabetes Technology Society.

Development of Laser, Detector, and Receiver Systems for an Atmospheric CO2 Lidar Profiling System

NASA Technical Reports Server (NTRS)

Ismail, Syed; Koch, Grady; Abedin, Nurul; Refaat, Tamer; Rubio, Manuel; Singh, Upendra

2008-01-01

A ground-based Differential Absorption Lidar (DIAL) is being developed with the capability to measure range-resolved and column amounts of atmospheric CO2. This system is also capable of providing high-resolution aerosol profiles and cloud distributions. It is being developed as part of the NASA Earth Science Technology Office s Instrument Incubator Program. This three year program involves the design, development, evaluation, and fielding of a ground-based CO2 profiling system. At the end of a three-year development this instrument is expected to be capable of making measurements in the lower troposphere and boundary layer where the sources and sinks of CO2 are located. It will be a valuable tool in the validation of NASA Orbiting Carbon Observatory (OCO) measurements of column CO2 and suitable for deployment in the North American Carbon Program (NACP) regional intensive field campaigns. The system can also be used as a test-bed for the evaluation of lidar technologies for space-application. This DIAL system leverages 2-micron laser technology developed under a number of NASA programs to develop new solid-state laser technology that provides high pulse energy, tunable, wavelength-stabilized, and double-pulsed lasers that are operable over pre-selected temperature insensitive strong CO2 absorption lines suitable for profiling of lower tropospheric CO2. It also incorporates new high quantum efficiency, high gain, and relatively low noise phototransistors, and a new receiver/signal processor system to achieve high precision DIAL measurements.

DialBetics

PubMed Central

Fujita, Hideo; Uchimura, Yuji; Omae, Koji; Aramaki, Eiji; Kato, Shigeko; Lee, Hanae; Kobayashi, Haruka; Kadowaki, Takashi; Ohe, Kazuhiko

2014-01-01

Numerous diabetes-management systems and programs for improving glycemic control to meet guideline targets have been proposed, using IT technology. But all of them allow only limited—or no—real-time interaction between patients and the system in terms of system response to patient input; few studies have effectively assessed the systems’ usability and feasibility to determine how well patients understand and can adopt the technology involved. DialBetics is composed of 4 modules: (1) data transmission module, (2) evaluation module, (3) communication module, and (4) dietary evaluation module. A 3-month randomized study was designed to assess the safety and usability of a remote health-data monitoring system, and especially its impact on modifying patient lifestyles to improve diabetes self-management and, thus, clinical outcomes. Fifty-four type 2 diabetes patients were randomly divided into 2 groups, 27 in the DialBetics group and 27 in the non-DialBetics control group. HbA1c and fasting blood sugar (FBS) values declined significantly in the DialBetics group: HbA1c decreased an average of 0.4% (from 7.1 ± 1.0% to 6.7 ± 0.7%) compared with an average increase of 0.1% in the non-DialBetics group (from 7.0 ± 0.9% to 7.1 ± 1.1%) (P = .015); The DialBetics group FBS decreased an average of 5.5 mg/dl compared with a non-DialBetics group average increase of 16.9 mg/dl (P = .019). BMI improvement—although not statistically significant because of the small sample size—was greater in the DialBetics group. DialBetics was shown to be a feasible and an effective tool for improving HbA1c by providing patients with real-time support based on their measurements and inputs. PMID:24876569

Ground-based DIAL and IPDA Systems for Remote Sensing of CO2, CH4, and H2O near 1.6 µm

NASA Astrophysics Data System (ADS)

Wagner, G. A.; Plusquellic, D. F.

2017-12-01

Integrated path differential absorption (IPDA) and differential absorption LIDAR (DIAL) are well established methods to monitor atmospheric constituents. At NIST, IPDA and DIAL systems have been developed as standoff systems and their overall performance has been evaluated through intercomparisons including the traceability to point sensor measurements. The all-fiber IPDA system is based on a low-power (< 13 mW, eye-safe) electro-optic modulated continuous-wave laser to produce 123 frequencies at a scan repetition frequency of 10 kHz.1 The transmitter-receiver system measures backscatter from natural targets and is rastered during the measurements to reduce speckle effects. The receiver consists of a 28 cm telescope, photomultiplier tube, and a streaming data acquisition system for direct photon discrimination and counting. The eye-safe DIAL system is based on an optical parametric oscillator2,3 that operates at a pulse repetition frequency of 100 Hz and alternates between on-line and off-line frequencies with pulse energies of < 10 mJ/pulse. The receivers consist of two telescopes (near field: 28 cm; far field: 40 cm), photomultiplier tubes, and a 2 GS/s hybrid data acquisition system for photon counting and current detection. We demonstrate the performance of the DIAL and IPDA systems and present results of a CO2 IPDA/DIAL/point sensor traceability study performed in Boulder (CO, USA) in summer 2017. 1. G. A. Wagner and D. F. Plusquellic, "Ground-Based, Integrated Path Differential Absorption LIDAR Measurement of CO2, CH4 and H2O near 1.6 µm," Applied Optics, 55(23), 6292-6310 (2016). 2. D. J. Armstrong, and A. V. Smith, "150-mJ 1550-nm KTA OPO with Good Beam Quality and High Efficiency," SPIE, 5337, 71-80 (2004). 3. K. O. Douglass, S. E. Maxwell, D. F. Plusquellic, J. T. Hodges, R. D. van Zee, D. V. Samarov, J. R. Whetstone, "Construction of a High Power OPO Laser System for Differential Absorption LIDAR," SPIE, 8159, 81590D (2011).

Advanced Opto-Electronics (LIDAR and Microsensor Development)

NASA Technical Reports Server (NTRS)

Vanderbilt, Vern C. (Technical Monitor); Spangler, Lee H.

2005-01-01

Our overall intent in this aspect of the project were to establish a collaborative effort between several departments at Montana State University for developing advanced optoelectronic technology for advancing the state-of-the-art in optical remote sensing of the environment. Our particular focus was on development of small systems that can eventually be used in a wide variety of applications that might include ground-, air-, and space deployments, possibly in sensor networks. Specific objectives were to: 1) Build a field-deployable direct-detection lidar system for use in measurements of clouds, aerosols, fish, and vegetation; 2) Develop a breadboard prototype water vapor differential absorption lidar (DIAL) system based on highly stable, tunable diode laser technology developed previously at MSU. We accomplished both primary objectives of this project, in developing a field-deployable direct-detection lidar and a breadboard prototype of a water vapor DIAL system. Paper summarizes each of these accomplishments.

High Power and Frequency-Agile Optical Parametric Oscillators for Airborne DIAL Measurements of CH4 and H2O

NASA Astrophysics Data System (ADS)

Nehrir, A. R.; Shuman, T.; Chuang, T.; Hair, J. W.; Refaat, T. F.; Ismail, S.; Kooi, S. A.; Notari, A.

2014-12-01

Atmospheric methane (CH4) has the second largest radiative forcing of the long-lived greenhouse gasses (GHG) after carbon dioxide. However, methane's much shorter atmospheric lifetime and much stronger warming potential make its radiative forcing equivalent to that for CO2 over a 20-year time horizon which makes CH4 a particularly attractive target for mitigation strategies. Similar to CH4, water vapor (H2O) is the most dominant of the short-lived GHG in the atmosphere and plays a key role in many atmospheric processes. Atmospheric H2O concentrations span over four orders of magnitude from the planetary boundary layer where high impact weather initiates to lower levels in the upper troposphere and lower stratosphere (UTLS) where water vapor has significant and long term impacts on the Earth's radiation budget. NASA Langley has fostered the technology development with Fibertek, Inc. to develop frequency agile and high power (> 3 W) pulsed lasers using similar architectures in the 1645 nm and 935 nm spectral bands for DIAL measurements of CH4 and H2O, respectively. Both systems utilize high power 1 kHz pulse repetition frequency Nd:YAG lasers to generate high power laser emission at the desired wavelength via optical parametric oscillators (OPO). The CH4 OPO, currently in its final build stage in a SBIR Phase II program has demonstrated >2 W average power with injection seeding from a distributed feedback (DFB) laser during risk reduction experiments. The H2O OPO has demonstrated high power operation (>2 W) during the SBIR Phase I program while being injection seeded with a DFB laser, and is currently funded via an SBIR Phase II to build a robust system for future integration into an airborne water vapor DIAL system capable of profiling from the boundary layer up to the UTLS. Both systems have demonstrated operation with active OPO wavelength control to allow for optimization of the DIAL measurements for operation at different altitudes and geographic regions. An update on the progress of the CH4 and H2O laser development will be presented which will focus on key laser characteristics such as pulse energy, frequency agility and spectral purity. DIAL simulations will also be presented based on the expected and measured laser characteristics and system parameters in anticipation of future system(s) development.

A Water Vapor Differential Absorption LIDAR Design for Unpiloted Aerial Vehicles

NASA Technical Reports Server (NTRS)

DeYoung, Russell J.; Mead, Patricia F.

2004-01-01

This system study proposes the deployment of a water vapor Differential Absorption LIDAR (DIAL) system on an Altair unmanned aerial vehicle (UAV) platform. The Altair offers improved payload weight and volume performance, and longer total flight time as compared to other commercial UAV's. This study has generated a preliminary design for an Altair based water vapor DIAL system. The design includes a proposed DIAL schematic, a review of mechanical challenges such as temperature and humidity stresses on UAV deployed DIAL systems, an assessment of the available capacity for additional instrumentation (based on the proposed design), and an overview of possible weight and volume improvements associated with the use of customized electronic and computer hardware, and through the integration of advanced fiber-optic and laser products. The results of the study show that less than 17% of the available weight, less than 19% of the volume capacity, and approximately 11% of the electrical capacity is utilized by the proposed water vapor DIAL system on the Altair UAV.

The NASA Langley High Altitude Lidar Observatory (HALO) - Advancements in Airborne DIAL Measurements of CH4 and H2O

NASA Astrophysics Data System (ADS)

Nehrir, A. R.; Hair, J. W.; Ferrare, R. A.; Hostetler, C. A.; Notari, A.; Collins, J. E., Jr.; Hare, R. J.; Harper, D. B.; Antill, C.; Cook, A. L.; Young, J.; Chuang, T.; Welch, W.

2016-12-01

Atmospheric methane (CH4) has the second largest radiative forcing of the long-lived greenhouse gasses (GHG) after carbon dioxide. However, methane's much shorter atmospheric lifetime and much stronger warming potential make its radiative forcing equivalent to that for CO2 over a 20-year time horizon which makes CH4 a particularly attractive target for mitigation strategies. Similar to CH4, water vapor (H2O) is the most dominant of the short-lived GHG in the atmosphere and plays a key role in many atmospheric processes. Atmospheric H2O concentrations span over four orders of magnitude from the planetary boundary layer where high impact weather initiates to lower levels in the upper troposphere and lower stratosphere where water vapor has significant and long term impacts on the Earth's radiation budget. Active remote sensing employing the differential absorption lidar (DIAL) technique enables scientific assessments of both natural and anthropogenic sources and sinks of CH4 with high accuracy and precision as well as and its impacts on the climate. The DIAL technique also allows for profiling of tropospheric water vapor for weather and climate applications with unprecedented spatial and temporal resolution. NASA Langley is developing the High Altitude Lidar Observatory (HALO) lidar system to address the observational needs of NASA's weather, climate, carbon cycle, and atmospheric composition focus areas. HALO is a multi-function airborne lidar being developed to measure atmospheric H2O and CH4 mixing ratios and aerosol and cloud optical properties using the DIAL and High Spectral Resolution Lidar (HSRL) techniques, respectively. HALO is designed as an airborne simulator for future space based DIAL missions and will serve as test bed for risk reduction of key technologies required of future space based GHG DIAL missions. A system level overview and up-to-date progress of the HALO lidar will be presented. Simulations on the expected accuracy and precision of HALO CH4 and H2O DIAL measurements will also be presented.

Advanced Atmospheric Water Vapor DIAL Detection System

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Elsayed-Ali, Hani E.; DeYoung, Russell J. (Technical Monitor)

2000-01-01

Measurement of atmospheric water vapor is very important for understanding the Earth's climate and water cycle. The remote sensing Differential Absorption Lidar (DIAL) technique is a powerful method to perform such measurement from aircraft and space. This thesis describes a new advanced detection system, which incorporates major improvements regarding sensitivity and size. These improvements include a low noise advanced avalanche photodiode detector, a custom analog circuit, a 14-bit digitizer, a microcontroller for on board averaging and finally a fast computer interface. This thesis describes the design and validation of this new water vapor DIAL detection system which was integrated onto a small Printed Circuit Board (PCB) with minimal weight and power consumption. Comparing its measurements to an existing DIAL system for aerosol and water vapor profiling validated the detection system.

Remote sensing of atmospheric NO2 by employing the continuous-wave differential absorption lidar technique.

PubMed

Mei, Liang; Guan, Peng; Kong, Zheng

2017-10-02

Differential absorption lidar (DIAL) technique employed for remote sensing has been so far based on the sophisticated narrow-band pulsed laser sources, which require intensive maintenance during operation. In this work, a continuous-wave (CW) NO 2 DIAL system based on the Scheimpflug principle has been developed by employing a compact high-power CW multimode 450 nm laser diode as the light source. Laser emissions at the on-line and off-line wavelengths of the NO 2 absorption spectrum are implemented by tuning the injection current of the laser diode. Lidar signals are detected by a 45° tilted area CCD image sensor satisfying the Scheimpflug principle. Range-resolved NO 2 concentrations on a near-horizontal path are obtained by the NO 2 DIAL system in the range of 0.3-3 km and show good agreement with those measured by a conventional air pollution monitoring station. A detection sensitivity of ± 0.9 ppbv at 95% confidence level in the region of 0.3-1 km is achieved with 15-minute averaging and 700 m range resolution during hours of darkness, which allows accurate concentration measurement of ambient NO 2 . The low-cost and robust DIAL system demonstrated in this work opens up many possibilities for field NO 2 remote sensing applications.

Gating characteristics of photomultiplier tubes for Lidar applications

NASA Technical Reports Server (NTRS)

Barrick, J. D. W.

1986-01-01

A detector test facility was developed and applied in the evaluation and characterization of lidar detectors in support of the multipurpose airborne differential absorption lidar (DIAL) system based at the Langley Research Center (LaRC). A performance data base of various detector configurations available to the DIAL system was obtained for optimum lidar detector selection. Photomultiplier tubes (PMT's) with multialkaline and bialkaline photocathodes were evaluated in voltage-divider networks (bases) by using either the focusing electrode or dynodes as a gating mechanism. Characteristics used for detector evaluation included gain stability, signal rise time, and the ability to block unwanted high light levels.

A Ground-Based 2-Micron DIAL System to Profile Tropospheric CO2 and Aerosol Distributions for Atmospheric Studies

NASA Technical Reports Server (NTRS)

Ismail, Syed; Koch, Grady; Abedin, Nurul; Refaat, Tamer; Rubio, Manuel; Davis, Kenneth; Miller, Charles; Singh, Upendra

2006-01-01

System will operate at a temperature insensitive CO2 line (2050.967 nm) with side-line tuning and off-set locking. Demonstrated an order of magnitude improvement in laser line locking needed for high precision measurements, side-line operation, and simultaneously double pulsing and line locking. Detector testing of phototransistor has demonstrated sensitivity to aerosol features over long distances in the atmosphere and resolve features approx. 100m. Optical systems that collect light onto small area detectors work well. Receiver optical designs are being optimized and data acquisition systems developed. CO2 line parameter characterization in progress In situ sensor calibration in progress for validation of DIAL CO2 system.

Information Retrieval Systems Retrieved? An Alternative to Present Dial Access Systems

ERIC Educational Resources Information Center

Hofmann, Norbert

1976-01-01

The expense of a dial access information retrieval system (DIARS) is weighed against its benefits. Problems of usage and efficacy for the student are outlined. A fully automated system is proposed instead, and its cost-saving features are pointed out. (MS)

NASA multipurpose airborne DIAL system and measurements of ozone and aerosol profiles. [DIfferential Absorption Lidar

NASA Technical Reports Server (NTRS)

Browell, E. V.; Carter, A. F.; Shipley, S. T.; Siviter, J. H., Jr.; Hall, W. M.; Allen, R. J.; Butler, C. F.; Mayo, M. N.

1983-01-01

The hardware, operational characteristics, data processing system, and applications of the NASA airborne differential absorption lidar (DIAL) system are described. DIAL functions by assessing the average gas concentration over a specified range interval by analyzing the difference in lidar backscatter signals for laser wavelengths tuned on and off of the molecular absorption line of a gas under investigation. The system comprises two frequency-doubled Nd:YAG lasers pumping two high conversion efficiency tunable dye lasers emitting pulses separated by 100 microsec or less. The return signals are digitized and stored on magnetic tape. The signal collector consists of photomultiplier tubes implanted in a cassegrain telescope. Flight tests of the system involved on-measurements at 285.95 nm and off-measurements at 299.40 nm, which yielded a differential cross section of 1.74 x 10 to the -16th sq cm. In situ measurements with another plane at a nominal altitude of 3.2 km for comparison purposes showed accuracy to within 10% in and above the boundary layer. The system is considered as a test apparatus for more developed versions to be flown on the Shuttle

First tests of a multi-wavelength mini-DIAL system for the automatic detection of greenhouse gases

NASA Astrophysics Data System (ADS)

Parracino, S.; Gelfusa, M.; Lungaroni, M.; Murari, A.; Peluso, E.; Ciparisse, J. F.; Malizia, A.; Rossi, R.; Ventura, P.; Gaudio, P.

2017-10-01

Considering the increase of atmospheric pollution levels in our cities, due to emissions from vehicles and domestic heating, and the growing threat of terrorism, it is necessary to develop instrumentation and gather know-how for the automatic detection and measurement of dangerous substances as quickly and far away as possible. The Multi- Wavelength DIAL, an extension of the conventional DIAL technique, is one of the most powerful remote sensing methods for the identification of multiple substances and seems to be a promising solution compared to existing alternatives. In this paper, first in-field tests of a smart and fully automated Multi-Wavelength mini-DIAL will be presented and discussed in details. The recently developed system, based on a long-wavelength infrared (IR-C) CO2 laser source, has the potential of giving an early warning, whenever something strange is found in the atmosphere, followed by identification and simultaneous concentration measurements of many chemical species, ranging from the most important Greenhouse Gases (GHG) to other harmful Volatile Organic Compounds (VOCs). Preliminary studies, regarding the fingerprint of the investigated substances, have been carried out by cross-referencing database of infrared (IR) spectra, obtained using in-cell measurements, and typical Mixing Ratios in the examined region, extrapolated from the literature. First experiments in atmosphere have been performed into a suburban and moderately-busy area of Rome. Moreover, to optimize the automatic identification of the harmful species to be recognized on the basis of in cell measurements of the absorption coefficient spectra, an advanced multivariate statistical method for classification has been developed and tested.

Solid-State 2-Micron Laser Transmitter Advancement for Wind and Carbon Dioxide Measurements From Ground, Airborne, and Space-Based Lidar Systems

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Kavaya, Michael J.; Koch, Grady; Yu, Jirong; Ismail, Syed

2008-01-01

NASA Langley Research Center has been developing 2-micron lidar technologies over a decade for wind measurements, utilizing coherent Doppler wind lidar technique and carbon dioxide measurements, utilizing Differential Absorption Lidar (DIAL) technique. Significant advancements have been made towards developing state-of-the-art technologies towards laser transmitters, detectors, and receiver systems. These efforts have led to the development of solid-state lasers with high pulse energy, tunablility, wavelength-stability, and double-pulsed operation. This paper will present a review of these technological developments along with examples of high resolution wind and high precision CO2 DIAL measurements in the atmosphere. Plans for the development of compact high power lasers for applications in airborne and future space platforms for wind and regional to global scale measurement of atmospheric CO2 will also be discussed.

DialBetics With a Multimedia Food Recording Tool, FoodLog: Smartphone-Based Self-Management for Type 2 Diabetes.

PubMed

Waki, Kayo; Aizawa, Kiyoharu; Kato, Shigeko; Fujita, Hideo; Lee, Hanae; Kobayashi, Haruka; Ogawa, Makoto; Mouri, Keisuke; Kadowaki, Takashi; Ohe, Kazuhiko

2015-05-01

Diabetes self-management education is an essential element of diabetes care. Systems based on information and communication technology (ICT) for supporting lifestyle modification and self-management of diabetes are promising tools for helping patients better cope with diabetes. An earlier study had determined that diet improved and HbA1c declined for the patients who had used DialBetics during a 3-month randomized clinical trial. The objective of the current study was to test a more patient-friendly version of DialBetics, whose development was based on the original participants' feedback about the previous version of DialBetics. DialBetics comprises 4 modules: data transmission, evaluation, exercise input, and food recording and dietary evaluation. Food recording uses a multimedia food record, FoodLog. A 1-week pilot study was designed to determine if usability and compliance improved over the previous version, especially with the new meal-input function. In the earlier 3-month, diet-evaluation study, HbA1c had declined a significant 0.4% among those who used DialBetics compared with the control group. In the current 1-week study, input of meal photos was higher than with the previous version (84.8 ± 13.2% vs 77.1% ± 35.1% in the first 2 weeks of the 3-month trial). Interviews after the 1-week study showed that 4 of the 5 participants thought the meal-input function improved; the fifth found input easier, but did not consider the result an improvement. DialBetics with FoodLog was shown to be an effective and convenient tool, its new meal-photo input function helping provide patients with real-time support for diet modification. © 2015 Diabetes Technology Society.

DialBetics With a Multimedia Food Recording Tool, FoodLog

PubMed Central

Waki, Kayo; Aizawa, Kiyoharu; Kato, Shigeko; Fujita, Hideo; Lee, Hanae; Kobayashi, Haruka; Ogawa, Makoto; Mouri, Keisuke; Kadowaki, Takashi; Ohe, Kazuhiko

2015-01-01

Background: Diabetes self-management education is an essential element of diabetes care. Systems based on information and communication technology (ICT) for supporting lifestyle modification and self-management of diabetes are promising tools for helping patients better cope with diabetes. An earlier study had determined that diet improved and HbA1c declined for the patients who had used DialBetics during a 3-month randomized clinical trial. The objective of the current study was to test a more patient-friendly version of DialBetics, whose development was based on the original participants’ feedback about the previous version of DialBetics. Method: DialBetics comprises 4 modules: data transmission, evaluation, exercise input, and food recording and dietary evaluation. Food recording uses a multimedia food record, FoodLog. A 1-week pilot study was designed to determine if usability and compliance improved over the previous version, especially with the new meal-input function. Results: In the earlier 3-month, diet-evaluation study, HbA1c had declined a significant 0.4% among those who used DialBetics compared with the control group. In the current 1-week study, input of meal photos was higher than with the previous version (84.8 ± 13.2% vs 77.1% ± 35.1% in the first 2 weeks of the 3-month trial). Interviews after the 1-week study showed that 4 of the 5 participants thought the meal-input function improved; the fifth found input easier, but did not consider the result an improvement. Conclusions: DialBetics with FoodLog was shown to be an effective and convenient tool, its new meal-photo input function helping provide patients with real-time support for diet modification. PMID:25883164

Current 2-μm dial measurements of atmospheric CO2 and expected results from space using new MCT APDS

NASA Astrophysics Data System (ADS)

Dumas, A.; Gibert, F.; Rothman, J.; Édouart, D.; Le Mounier, F.; Cénac, C.

2017-11-01

In the framework of CO2 monitoring in the Atmospheric Boundary Layer (ABL), a ground-based 2-μm Differential Absorption Lidar (DIAL) has been developed at the Laboratoire de Météorologie Dynamique (LMD) in Palaiseau. In order to derive flux information, this system has been set up with coherent detection, which allows to combine CO2 density measurements with wind velocity measurements. On the other hand, new advances in the field of Mercury Cadmium Tellure (MCT) Avalanche Photodiodes (APDs) open the way for high-precision measurements in direct detection ultimately from space. In this study, we first report on state of the art measurements obtained with the current coherent DIAL system before presenting expected results for a similar laser transmitter equipped with MCT APDs. For this latter part, we use a numerical model which relies on APDs performance data provided by the Laboratoire d'Électronique et de Technologie de l'Information (LETI).

Feasibility Study For A Spaceborne Ozone/Aerosol Lidar System

NASA Technical Reports Server (NTRS)

Campbell, Richard E.; Browell, Edward V.; Ismail, Syed; Dudelzak, Alexander E.; Carswell, Allan I.; Ulitsky, Arkady

1997-01-01

Because ozone provides a shield against harmful ultraviolet radiation, determines the temperature profile in the stratosphere, plays important roles in tropospheric chemistry and climate, and is a health risk near the surface, changes in natural ozone layers at different altitudes and their global impact are being intensively researched. Global ozone coverage is currently provided by passive optical and microwave satellite sensors that cannot deliver high spatial resolution measurements and have particular limitations in the troposphere. Vertical profiling DIfferential Absorption Lidars (DIAL) have shown excellent range-resolved capabilities, but these systems have been large, inefficient, and have required continuous technical attention for long term operations. Recently, successful, autonomous DIAL measurements have been performed from a high-altitude aircraft (LASE - Lidar Atmospheric Sensing Experiment), and a space-qualified aerosol lidar system (LITE - Laser In-space Technology Experiment) has performed well on Shuttle. Based on the above successes, NASA and the Canadian Space Agency are jointly studying the feasibility of developing ORACLE (Ozone Research with Advanced Cooperative Lidar Experiments), an autonomously operated, compact DIAL instrument to be placed in orbit using a Pegasus class launch vehicle.

Comparison of ozone profiles obtained with NIES DIAL and SAGE II measurements

NASA Technical Reports Server (NTRS)

Nakane, Hideaki; Sasano, Yasuhiro; Hayashida-Amano, Sachiko; Sugimoto, Nobuo; Matsui, Ichiro; Minato, Atsushi; Mccormick, M. P.

1993-01-01

Ozone profiles obtained with the Differential Absorption Lidar (DIAL) system at the National Institute for Environmental Studies (NIES) (Tsukuba, Japan) were compared with data provided by the satellite sensor SAGE II. The SAGE II data were selected based on criteria of spatial and temporal differences between the DIAL and the SAGE II measurements: five degrees in latitude and 15 degrees in longitude, within a latitudinal band from 31 deg to 41 deg N, and within one, three and five days after or before the DIAL measurements. Results show very good agreement for the individual and the zonal-mean profiles. The average mean difference between the DIAL and the SAGE II measurements over the altitudes 15-50 km was about 10 percent.

47 CFR 90.475 - Operation of internal transmitter control systems in specially equipped systems.

Code of Federal Regulations, 2012 CFR

2012-10-01

... telephone network (PSTN), nor uses dial-up circuits in the PSTN. Licensees with complex communications... access these base stations through the microwave or operational fixed systems from positions in the PSTN... circuit is provided for each mode of transmitter operation (i.e., conventional, dial-up or Internet). (3...

47 CFR 90.475 - Operation of internal transmitter control systems in specially equipped systems.

Code of Federal Regulations, 2013 CFR

2013-10-01

... telephone network (PSTN), nor uses dial-up circuits in the PSTN. Licensees with complex communications... access these base stations through the microwave or operational fixed systems from positions in the PSTN... circuit is provided for each mode of transmitter operation (i.e., conventional, dial-up or Internet). (3...

47 CFR 90.475 - Operation of internal transmitter control systems in specially equipped systems.

Code of Federal Regulations, 2014 CFR

2014-10-01

... telephone network (PSTN), nor uses dial-up circuits in the PSTN. Licensees with complex communications... access these base stations through the microwave or operational fixed systems from positions in the PSTN... circuit is provided for each mode of transmitter operation (i.e., conventional, dial-up or Internet). (3...

47 CFR 90.475 - Operation of internal transmitter control systems in specially equipped systems.

Code of Federal Regulations, 2011 CFR

2011-10-01

... telephone network (PSTN), nor uses dial-up circuits in the PSTN. Licensees with complex communications... access these base stations through the microwave or operational fixed systems from positions in the PSTN... circuit is provided for each mode of transmitter operation (i.e., conventional, dial-up or Internet). (3...

A Direct Detection 1.6μm DIAL with Three Wavelengths for Measurements of Vertical CO2 Concentration and Temperature Profiles in the Atmosphere

NASA Astrophysics Data System (ADS)

Nagasawa, C.; Abo, M.; Shibata, Y.; Nagai, T.; Tsukamoto, M.

2012-12-01

We report the new 1.6 μm DIAL system that can measure the temperature profiles with the CO2 concentration profiles in the atmosphere because of improvement of measurement accuracy of the CO2 density and mixing ratio (ppm). We have developed a direct detection 1.6 μm differential absorption lidar (DIAL) technique to perform range-resolved measurements of vertical CO2 concentration profiles in the atmosphere [Sakaizawa et al. 2009]. Our 1.6 μm DIAL system consists of the Optical Parametric Generator (OPG) transmitter that excited by the LD pumped Nd:YAG laser with high repetition rate (500 Hz) and the receiving optics that included the near-infrared photomultiplier tube with high quantum efficiency operating at the photon counting mode and the telescope with larger aperture than that of the coherent detection method. Laser beams of three wavelengths around a CO2 absorption line is transmitted alternately to the atmosphere for measurements of CO2 concentration and temperature profiles. Moreover, a few retrieval algorithms of CO2-DIAL are also performed for improvement of measurement accuracy. The accurate vertical CO2 profiles in the troposphere are highly desirable in the inverse techniques to improve quantification and understanding of the global budget of CO2 and also global climate changes [Stephens et al. 2007]. In comparison with the ground-based monitoring network, CO2 measurements for vertical profiles in the troposphere have been limited to campaign-style aircraft and commercial airline observations with the limited spatial and temporal coverage. This work was financially supported by the System Development Program for Advanced Measurement and Analysis of the Japan Science and Technology Agency. References Sakaizawa, D., C. Nagasawa, T. Nagai, M. Abo, Y. Shibata, H. Nagai, M. Nakazato, and T. Sakai, Development of a 1.6μm differential absorption lidar with a quasi-phase-matching optical parametric oscillator and photon-counting detector for the vertical CO2 profile, Applied Optics, Vol.48, No.4, pp.748-757, 2009. Stephens, B. B. et al., Weak Northern and Strong Tropical Land Carbon Uptake from Vertical Profiles of Atmospheric CO2, Science 316, pp.1732-1735, 2007.

Integrated Dial-A-Ride and Fixed Route Transit in Ann Arbor, Michigan

DOT National Transportation Integrated Search

1977-03-01

The report describes the development, implementation, and current status of the Teltran system as it existed in the spring of 1976. In particular, this evaluation provides a detailed description of Teltran system configuration (and changes in that co...

CO2 DIAL system: construction, measurements, and future development

NASA Astrophysics Data System (ADS)

Vicenik, Jiri

1999-07-01

A miniature CO2 DIAL system has been constructed. Dimension of the system are 500 X 450 X 240 mm, its mass is only 28 kg. The system consists of two tunable TEA CO2 lasers, receiving optics, IR detector, signal processing electronics and single chip microcomputer with display. The lasers are tuned manually by means of micrometric screw and are capable to generate pulses on more than 50 CO2 laser lines. The output energy is 50 mJ. The system was tested using various toxic gases and simulants, mostly at range 300 m, most of the measurements were done using pyrodetector in the receiver. The system shows good sensitivity, but it exhibits substantial instability of zero concentration. In the next stage the work will be concentrated on use of high-sensitivity MCT detector in the receiver and implementation of automatic tuning of lasers to the system.

New lidar challenges for gas hazard management in industrial environments

NASA Astrophysics Data System (ADS)

Cézard, Nicolas; Liméry, Anasthase; Bertrand, Johan; Le Méhauté, Simon; Benoit, Philippe; Fleury, Didier; Goular, Didier; Planchat, Christophe; Valla, Matthieu; Augère, Béatrice; Dolfi-Bouteyre, Agnès.

2017-10-01

The capability of Lidars to perform range-resolved gas profiles makes them an appealing choice for many applications. In order to address new remote sensing challenges, arising from industrial contexts, Onera currently develops two lidar systems, one Raman and one DIAL. On the Raman side, a high spatial-resolution multi-channel Raman Lidar is developed in partnership with the French National Radioactive Waste Management Agency (Andra). This development aims at enabling future monitoring of hydrogen gas and water vapor profiles inside disposal cells containing radioactive wastes. We report on the development and first tests of a three-channel Raman Lidar (H2, H2O, N2) designed to address this issue. Simultaneous hydrogen and water vapor profiles have been successfully performed along a 5m-long gas cell with 1m resolution at a distance of 85 m. On the DIAL side, a new instrumental concept is being explored and developed in partnership with Total E and P. The objective is to perform methane plume monitoring and flux assessment in the vicinity of industrials plants or platforms. For flux assessment, both gas concentration and air speed must be profiled by lidar. Therefore, we started developing a bi-function, all-fiber, coherent DIAL/Doppler Lidar. The first challenge was to design and build an appropriate fiber laser source. The achieved demonstrator delivers 200 W peak power, polarized, spectrally narrow (<15 MHz), 110 ns pulses of light out of a monomode fiber at 1645 nm. It fulfills the requirements for a future implementation in a bi-function Dial/Doppler lidar with km-range expectation. We report on the laser and lidar architecture, and on first lidar tests at 1645 nm.

LASE

Atmospheric Science Data Center

2017-03-16

... Absorption Lidar (DIAL) system developed to measure water vapor, aerosol, and cloud profiles. These measurements can be used in ... heat flux, the water vapor component of the hydrologic cycle, and atmospheric transport using water vapor as a tracer of atmospheric ...

The High Accuracy Measurement of CO2 Mixing Ratio Profiles Using Ground Based 1.6 μm CO2-DIAL with Temperature Measurement Techniques in the Lower-Atmosphere

NASA Astrophysics Data System (ADS)

Abo, M.; Shibata, Y.; Nagasawa, C.

2017-12-01

We have developed a ground based direct detection three-wavelength 1.6 μm differential absorption lidar (DIAL) to achieve measurements of vertical CO2 concentration and temperature profiles in the atmosphere. As the spectra of absorption lines of any molecules are influenced basically by the temperature and pressure in the atmosphere, it is important to measure them simultaneously so that the better accuracy of the DIAL measurement is realized. Conventionally, we have obtained the vertical profile of absorption cross sections using the atmospheric temperature profile by the objective analysis and the atmospheric pressure profile calculated by the pressure height equation. Comparison of atmospheric pressure profiles calculated from this equation and those obtained from radiosonde observations at Tateno, Japan is consistent within 0.2 % below 3 km altitude. But the temperature dependency of the CO2 density is 0.25 %/°C near the surface. Moreover, the CO2 concentration is often evaluated by the mixing ratio. Because the air density is related by the ideal gas law, the mixing ratio is also related by the atmospheric temperature. Therefore, the temperature affects not only accuracy of CO2 concentration but the CO2 mixing ratio. In this paper, some experimental results of the simultaneous measurement of atmospheric temperature profiles and CO2 mixing ratio profiles are reported from 0.4 to 2.5 km altitude using the three-wavelength 1.6 μm DIAL system. Temperature profiles of CO2 DIAL measurement were sometimes different from those of objective analysis below 1.5 km altitude. These differences are considered to be due to regionality at the lidar site. The temperature difference of 5.0 °C corresponds to a CO2 mixing ratio difference of 8.0 ppm at 500 m altitude. This cannot be ignored in estimates of regional sources and sinks of CO2. This three-wavelength CO2 DIAL technique can estimate accurately temporal behavior of CO2 mixing ratio profiles in the lower atmosphere. This work was financially supported by the System Development Program for Advanced Measurement and Analysis of the Japan Science and Technology Agency.

User perceptions of the knowledge underpinning practice orientation dial (KUPOD) as a tool to enhance learning.

PubMed

Borlase, Jeanette; Abelson-Mitchell, Nadine

2008-01-01

The concern of academics and clinicians about the alleged dichotomy between theoretical concepts and the practice of nursing has been the catalyst for the development of a pocket-sized aid for nurses, known as the Knowledge Underpinning Practice Orientation Dial (KUPOD [N]/The Dial). A mixed method approach was used incorporating a questionnaire and a focus group of educators. The Dial was introduced, as part of a module, undertaken by a cohort of second-year Diploma in Nursing (Adult Branch) students. Twenty-eight students returned the questionnaire (response rate=85%). Results revealed that the Dial was easy to use in a variety of situations and locations. Respondents used the Dial within clinical and classroom settings and for self directed study. They reported that it was a practical and effective aid to learning, assisting in correlating theory and practice. It supported reflection and enhanced confidence in the clinical area, indicating that this economically produced tool helps to bridge the theory-practice gap. The Dial is now being introduced as a learning resource to a wider range of students.

Development of the Lidar Atmospheric Sensing Experiment (LASE): An Advanced Airborne DIAL Instrument

NASA Technical Reports Server (NTRS)

Moore, Alvah S., Jr.; Brown, Kevin E.; Hall, William M.; Barnes, James C.; Edwards, William C.; Petway, Larry B.; Little, Alan D.; Luck, William S., Jr.; Jones, Irby W.; Antill, Charles W., Jr.

1997-01-01

The Lidar Atmospheric Sensing Experiment (LASE) Instrument is the first fully-engineered, autonomous Differential Absorption Lidar (DIAL) System for the measurement of water vapor in the troposphere (aerosol and cloud measurements are included). LASE uses a double-pulsed Ti:Sapphire laser for the transmitter with a 30 ns pulse length and 150 mJ/pulse. The laser beam is "seeded" to operate on a selected water vapor absorption line in the 815-nm region using a laser diode and an onboard absorption reference cell. A 40 cm diameter telescope collects the backscattered signals and directs them onto two detectors. LASE collects DIAL data at 5 Hz while onboard a NASA/Ames ER-2 aircraft flying at altitudes from 16-21 km. LASE was designed to operate autonomously within the environment and physical constraints of the ER-2 aircraft and to make water vapor profile measurements across the troposphere to better than 10% accuracy. LASE has flown 19 times during the development of the instrument and the validation of the science data. This paper describes the design, operation, and reliability of the LASE Instrument.

Setting up a mobile Lidar (DIAL) system for detecting chemical warfare agents

NASA Astrophysics Data System (ADS)

Kavosh Tehrani, M.; Mohammad, M. Malek; Jaafari, E.; Mobashery, A.

2015-03-01

The mobile light detection and ranging DIAL system of Malek Ashtar University of Technology has been developed for the detection of chemical warfare agents whose absorption wavelengths are in the range of 9.2-10.8 μm tunable CO2 lasers of the system. In this paper, this system is first described and then ammonia detection is analyzed experimentally. Also, experimental results of detecting a sarin agent simulant, dimethyl-methyl phosphonate (DMMP), are presented. The power levels received from different ranges to detect specific concentrations of NH3 and DMMP have been measured and debated. The primary test results with a 150 ns clipped pulse width by passive pinhole plasma shutter indicate that the system is capable of monitoring several species of pollutants in the range of about 1 km, with a 20 m spatial and 2 min temporal resolution.

Remote Access to CD-ROM for the Distant Learner.

ERIC Educational Resources Information Center

Cutright, Patricia; Girrard, Kenneth M.

1991-01-01

A dial-access, multiuser, multiaccess CD-ROM search system with end-user capability was developed to provide Eastern Oregon State College distance education students with access to the information required by their studies. Based on UNIX, the system provides students with access to 12 databases, an e-mail system for messaging, interlibrary loan…

Lower-free tropospheric ozone dial measurements over Athens, Greece

NASA Astrophysics Data System (ADS)

Mytilinaios, Michail; Papayannis, Alexandros; Tsaknakis, Georgios

2018-04-01

A compact ozone differential absorption lidar (DIAL) was implemented at the Laboratory of Laser Remote Sensing of the National Technical University of Athens (NTUA), in Athens, Greece. The DIAL system is based on a Nd:YAG laser emitting at 266 nm. A high-pressure Raman cell, filled with D2, was used to generate the λON and λOFF laser wavelength pairs (i.e., 266-289 nm and 289-316 nm, respectively) based on the Stimulated Raman Scattering (SRS) effect. The system was run during daytime and nighttime conditions to obtain the vertical profile of tropospheric ozone in the Planetary Boundary Layer (PBL) and the adjacent free troposphere.

Airborne UV DIAL Measurements of Ozone and Aerosols

NASA Technical Reports Server (NTRS)

Grant, William B.; Browell, Edward V.

2000-01-01

The NASA Langley Research Center's airborne UV Differential Absorption Lidar (DIAL) system measures vertical profiles of ozone and aerosols above and below the aircraft along its flight track. This system has been used in over 20 airborne field missions designed to study the troposphere and stratosphere since 1980. Four of these missions involved tropospheric measurement programs in the Pacific Ocean with two in the western North Pacific and two in the South Pacific. The UV DIAL system has been used in these missions to study such things as pollution outflow, long-range transport, and stratospheric intrusions; categorize the air masses encountered; and to guide the aircraft to altitudes where interesting features can be studied using the in situ instruments. This paper will highlight the findings with the UV DIAL system in the Pacific Ocean field programs and introduce the mission planned for the western North Pacific for February-April 2001. This will be an excellent opportunity for collaboration between the NASA airborne mission and those with ground-based War systems in Asia Pacific Rim countries to make a more complete determination of the transport of air from Asia to the western Pacific.

DIAL with heterodyne detection including speckle noise: Aircraft/shuttle measurements of O3, H2O, and NH3 with pulsed tunable CO2 lasers

NASA Technical Reports Server (NTRS)

Brockman, P.; Hess, R. V.; Staton, L. D.; Bair, C. H.

1980-01-01

Atmospheric trace constituent measurements with higher vertical resolution than attainable with passive radiometers are discussed. Infrared differential absorption lidar (DIAL), which depends on Mie scattering from aerosols, has special advantages for tropospheric and lower stratospheric applications and has great potential importance for measurements from shuttle and aircraft. Differential absorption lidar data reduction involves comparing large amplitude signals which have small differences. The accuracy of the trace constituent concentration inferred from DIAL measurements depends strongly on the errors in determining the amplitude of the signals. Thus, the commonly used SNR expression (signal divided by noise in the absence of signal) is not adequate to describe DIAL measurement accuracy and must be replaced by an expression which includes the random coherent (speckle) noise within the signal. A comprehensive DIAL computer algorithm is modified to include heterodyne detection and speckle noise. Examples for monitoring vertical distributions of O3, H2O, and NH3 using a ground-, aircraft-, or shuttle-based pulsed tunable CO2 laser DIAL system are given.

Lidar and Dial application for detection and identification: a proposal to improve safety and security

NASA Astrophysics Data System (ADS)

Gaudio, P.; Malizia, A.; Gelfusa, M.; Murari, A.; Parracino, S.; Poggi, L. A.; Lungaroni, M.; Ciparisse, J. F.; Di Giovanni, D.; Cenciarelli, O.; Carestia, M.; Peluso, E.; Gabbarini, V.; Talebzadeh, S.; Bellecci, C.

2017-01-01

Nowadays the intentional diffusion in air (both in open and confined environments) of chemical contaminants is a dramatic source of risk for the public health worldwide. The needs of a high-tech networks composed by software, diagnostics, decision support systems and cyber security tools are urging all the stakeholders (military, public, research & academic entities) to create innovative solutions to face this problem and improve both safety and security. The Quantum Electronics and Plasma Physics (QEP) Research Group of the University of Rome Tor Vergata is working since the 1960s on the development of laser-based technologies for the stand-off detection of contaminants in the air. Up to now, four demonstrators have been developed (two LIDAR-based and two DIAL-based) and have been used in experimental campaigns during all 2015. These systems and technologies can be used together to create an innovative solution to the problem of public safety and security: the creation of a network composed by detection systems: A low cost LIDAR based system has been tested in an urban area to detect pollutants coming from urban traffic, in this paper the authors show the results obtained in the city of Crotone (south of Italy). This system can be used as a first alarm and can be coupled with an identification system to investigate the nature of the threat. A laboratory dial based system has been used in order to create a database of absorption spectra of chemical substances that could be release in atmosphere, these spectra can be considered as the fingerprints of the substances that have to be identified. In order to create the database absorption measurements in cell, at different conditions, are in progress and the first results are presented in this paper.

CO2 lidar for measurements of trace gases and wind velocities

NASA Technical Reports Server (NTRS)

Hess, R. V.

1982-01-01

CO2 lidar systems technology and signal processing requirements relevant to measurement needs and sensitivity are discussed. Doppler processing is similar to microwave radar, with signal reception controlled by a computer capable of both direct and heterodyne operations. Trace gas concentrations have been obtained with the NASA DIAL system, and trace gas transport has been determined with Doppler lidar measurements for wind velocity and turbulence. High vertical resolution measurement of trace gases, wind velocity, and turbulence are most important in the planetary boundary layer and in regions between the PBL and the lower stratosphere. Shear measurements are critical for airport operational safety. A sensitivity analysis for heterodyne detection with the DIAL system and for short pulses using a Doppler lidar system is presented. The development of transient injection locking techniques, as well as frequency stability by reducing chirp and catalytic control of closed cycle CO2 laser chemistry, is described.

The McCarron-Dial System--An Approach to Clinical, Vocational, and Educational Evaluation.

ERIC Educational Resources Information Center

Dial, Jack G.; And Others

The McCarron-Dial System is useful for both vocational and clinical evaluation of neuropsychologically disabled adults. Five factors (verbal-cognitive, sensory, motor, emotional, and integration coping) are used to predict vocational competency, which is measured by work samples and behavior scales, during the first twelve months of a client's…

Monitoring fugitive methane and natural gas emissions, validation of measurement techniques.

NASA Astrophysics Data System (ADS)

Robinson, Rod; Innocenti, Fabrizio; Gardiner, Tom; Helmore, Jon; Finlayson, Andrew; Connor, Andy

2017-04-01

The detection and quantification of fugitive and diffuse methane emissions has become an increasing priority in recent years. As the requirements for routine measurement to support industry initiatives increase there is a growing requirement to assess and validate the performance of fugitive emission measurement technologies. For reported emissions traceability and comparability of measurements is important. This talk will present recent work addressing these needs. Differential Absorption Lidar (DIAL) is a laser based remote sensing technology, able to map the concentration of gases in the atmosphere and determine emission fluxes for fugitive emissions. A description of the technique and its application for determining fugitive emissions of methane from oil and gas operations and waste management sites will be given. As DIAL has gained acceptance as a powerful tool for the measurement and quantification of fugitive emissions, and given the rich data it produces, it is being increasingly used to assess and validate other measurement approaches. In addition, to support the validation of technologies, we have developed a portable controlled release facility able to simulate the emissions from area sources. This has been used to assess and validate techniques which are used to monitor emissions. The development and capabilities of the controlled release facility will be described. This talk will report on recent studies using DIAL and the controlled release facility to validate fugitive emission measurement techniques. This includes side by side comparisons of two DIAL systems, the application of both the DIAL technique and the controlled release facility in a major study carried out in 2015 by South Coast Air Quality Management District (SCAQMD) in which a number of optical techniques were assessed and the development of a prototype method validation approach for techniques used to measure methane emissions from shale gas sites. In conclusion the talk will provide an update on the current status in the development of a European Standard for the measurement of fugitive emissions of VOCs and the use of validation data in the standardisation process and discuss the application of this to methane measurement.

Two Wavelength Ti:sapphire Laser for Ozone DIAL Measurements from Aircraft

NASA Technical Reports Server (NTRS)

Situ, Wen; DeYoung, Russel J.

1998-01-01

Laser remote sensing of ozone from aircraft has proven to be a valuable technique for understanding the distribution and dynamics of ozone in the atmosphere. Presently the differential absorption lidar (DIAL) technique, using dual ND:YAG lasers that are doubled to pump dye lasers which in turn are doubled into the UV for the "on" and "off' line lasers, is used on either the NASA DC-8 or P-3 aircraft. Typically, the laser output for each line is 40-mJ and this is split into two beams, one looking up and the other downward, each beam having about 20-mJ. The residual ND:YAG (1.06 micron) and dye laser energies are also transmitted to obtain information on the atmospheric aerosols. While this system has operated well, there are several system characteristics that make the system less than ideal for aircraft operations. The system, which uses separate "on" and "off" line lasers, is quite large and massive requiring valuable aircraft volume and weight. The dye slowly degrades with time requiring replacement. The laser complexity requires a number of technical people to maintain the system performance. There is also the future interest in deploying an ozone DIAL system in an Unpiloted Atmospheric Vehicle (UAV) which would require a total payload mass of less than 150 kg and power requirement of less than 1500 W. A laser technology has emerged that could potentially provide significant enhancements over the present ozone DIAL system. The flashlamp pumped Ti:sapphire laser system is an emerging technology that could reduce the mass and volume over the present system and also provide a system with fewer conversion steps, reducing system complexity. This paper will discuss preliminary results from a flashlamp-pumped Ti:sapphire laser constructed as a radiation source for a UV DIAL system to measure ozone.

Comparison of ozone profiles from DIAL, MLS, and chemical transport model simulations over Río Gallegos, Argentina, during the spring Antarctic vortex breakup, 2009

NASA Astrophysics Data System (ADS)

Sugita, Takafumi; Akiyoshi, Hideharu; Wolfram, Elián; Salvador, Jacobo; Ohyama, Hirofumi; Mizuno, Akira

2017-12-01

This study evaluates the agreement between ozone profiles derived from the ground-based differential absorption lidar (DIAL), satellite-borne Aura Microwave Limb Sounder (MLS), and 3-D chemical transport model (CTM) simulations such as the Model for Interdisciplinary Research on Climate (MIROC-CTM) over the Atmospheric Observatory of Southern Patagonia (Observatorio Atmosférico de la Patagonia Austral, OAPA; 51.6° S, 69.3° W) in Río Gallegos, Argentina, from September to November 2009. In this austral spring, measurements were performed in the vicinity of the polar vortex and inside it on some occasions; they revealed the variability in the potential vorticity (PV) of measured air masses. Comparisons between DIAL and MLS were performed between 6 and 100 hPa with 500 km and 24 h coincidence criteria. The results show a good agreement between DIAL and MLS with mean differences of ±0.1 ppmv (MLS - DIAL, n = 180) between 6 and 56 hPa. MIROC-CTM also agrees with DIAL, with mean differences of ±0.3 ppmv (MIROC-CTM - DIAL, n = 23) between 10 and 56 hPa. Both comparisons provide mean differences of 0.5 ppmv (MLS) to 0.8-0.9 ppmv (MIROC-CTM) at the 83-100 hPa levels. DIAL tends to underestimate ozone values at this lower altitude region. Between 6 and 8 hPa, the MIROC-CTM ozone value is 0.4-0.6 ppmv (5-8 %) smaller than those from DIAL. Applying the scaled PV (sPV) criterion for matching pairs in the DIAL-MLS comparison, the variability in the difference decreases 21-47 % between 10 and 56 hPa. However, the mean differences are small for all pressure levels, except 6 hPa. Because ground measurement sites in the Southern Hemisphere (SH) are very sparse at mid- to high latitudes, i.e., 35-60° S, the OAPA site is important for evaluating the bias and long-term stability of satellite instruments. The good performance of this DIAL system will be useful for such purposes in the future.

Measurements of CO2 Concentration and Wind Profiles with A Scanning 1.6μm DIAL

NASA Astrophysics Data System (ADS)

Abo, M.; Shibata, Y.; Nagasawa, C.; Nagai, T.; Sakai, T.; Tsukamoto, M.

2012-12-01

Horizontal carbon dioxide (CO2) distribution and wind profiles are important information for understanding of the regional sink and source of CO2. The differential absorption lidar (DIAL) and the Doppler lidar with the range resolution is expected to bring several advantages over passive measurements. We have developed a new scanning 1.6μm DIAL and incoherent Doppler lidar system to perform simultaniously measurements of CO2 concentration and wind speed profiles in the atmosphere. The 1.6μm DIAL and Doppler lidar system consists of the Optical Parametric Generator (OPG) transmitter that excited by the LD pumped Nd:YAG laser with high repetition rate (500 Hz). The receiving optics include the near-infrared photomultiplier tube with high quantum efficiency operating at the photon counting mode, a fiber Bragg grating (FBG) filter to detct Doppler shift, and a 25 cm telescope[1][2]. Laser beam is transmitted coaxially and motorized scanning mirror system can scan the laser beam and field of view 0-360deg horizontally and 0-52deg vertically. We report the results of vertical CO2 scanning measurenents and vertical wind profiles. The scanning elevation angles were from 12deg to 24deg with angular step of 4deg and CO2 concentration profiles were obtained up to 1 km altitude with 200 m altitude resolution. We also obtained vertical wind vector profiles by measuring line-of-sight wind profiles at two azimuth angles with a fixed elevation angle 52deg. Vertical wind vector profiles were obtained up to 5 km altitude with 1 km altitude rasolution. This work was financially supported by the System Development Program for Advanced Measurement and Analysis of the Japan Science and Technology Agency. References [1] L. B. Vann, et al., "Narrowband fiber-optic phase-shifted Fabry-Perot Bragg grating filters for atmospheric water vapor lidar measurements", Appl. Opt., 44, pp. 7371-7377 (2005). [2] Y. Shibata, et al., "1.5μm incoherent Doppler lidar using a FBG filter", Proceedings of 25th International Laser Radar Conference (ILRC25), pp. 338-340 (2010)

A New Technique for the Retrieval of Near Surface Water Vapor Using DIAL Measurements

NASA Technical Reports Server (NTRS)

Ismail, Syed; Kooi, Susan; Ferrare, Richard; Winker, David; Hair, Johnathan; Nehrir, Amin; Notari, Anthony; Hostetler, Chris

2015-01-01

Water vapor is one of the most important atmospheric trace gas species and influences radiation, climate, cloud formation, surface evaporation, precipitation, storm development, transport, dynamics, and chemistry. For improvements in NWP (numerical weather prediction) and climate studies, global water vapor measurements with higher accuracy and vertical resolution are needed than are currently available. Current satellite sensors are challenged to characterize the content and distribution of water vapor in the Boundary Layer (BL) and particularly near the first few hundred meters above the surface within the BL. These measurements are critically needed to infer surface evaporation rates in cloud formation and climate studies. The NASA Langley Research Center Lidar Atmospheric Sensing Experiment (LASE) system, which uses the Differential Absorption Lidar (DIAL) technique, has demonstrated the capability to provide high quality water vapor measurements in the BL and across the troposphere. A new retrieval technique is investigated to extend these DIAL water vapor measurements to the surface. This method uses signals from both atmospheric backscattering and the strong surface returns (even over low reflectivity oceanic surfaces) using multiple gain channels to cover the large signal dynamic range. Measurements can be made between broken clouds and in presence of optically thin cirrus. Examples of LASE measurements from a variety of conditions encountered during NASA hurricane field experiments over the Atlantic Ocean are presented. Comparisons of retrieved water vapor profiles from LASE near the surface with dropsonde measurements show very good agreement. This presentation also includes a discussion of the feasibility of developing space-based DIAL capability for high resolution water vapor measurements in the BL and above and an assessment of the technology needed for developing this capability.

xDSL connection monitor

DOEpatents

Horton, John J.

2006-04-11

A system and method of maintaining communication between a computer and a server, the server being in communication with the computer via xDSL service or dial-up modem service, with xDSL service being the default mode of communication, the method including sending a request to the server via xDSL service to which the server should respond and determining if a response has been received. If no response has been received, displaying on the computer a message (i) indicating that xDSL service has failed and (ii) offering to establish communication between the computer and the server via the dial-up modem, and thereafter changing the default mode of communication between the computer and the server to dial-up modem service. In a preferred embodiment, an xDSL service provider monitors dial-up modem communications and determines if the computer dialing in normally establishes communication with the server via xDSL service. The xDSL service provider can thus quickly and easily detect xDSL failures.

Ultra Narrowband Optical Filters for Water Vapor Differential Absorption Lidar (DIAL) Atmospheric Measurements

NASA Technical Reports Server (NTRS)

Stenholm, Ingrid; DeYoung, Russell J.

2001-01-01

Differential absorption lidar (DIAL) systems are being deployed to make vertical profile measurements of atmospheric water vapor from ground and airborne platforms. One goal of this work is to improve the technology of such DIAL systems that they could be deployed on space-based platforms. Since background radiation reduces system performance, it is important to reduce it. One way to reduce it is to narrow the bandwidth of the optical receiver system. However, since the DIAL technique uses two or more wavelengths, in this case separated by 0.1 nm, a fixed-wavelength narrowband filter that would encompass both wavelengths would be broader than required for each line, approximately 0.02 nm. The approach employed in this project is to use a pair of tunable narrowband reflective fiber Bragg gratings. The Bragg gratings are germanium-doped silica core fiber that is exposed to ultraviolet radiation to produce index-of-refraction changes along the length of the fiber. The gratings can be tuned by stretching. The backscattered laser radiation is transmitted through an optical circulator to the gratings, reflected back to the optical circulator by one of the gratings, and then sent to a photodiode. The filter reflectivities were >90 percent, and the overall system efficiency was 30 percent.

Emerging solid-state laser technology by lidar/DIAL remote sensing

NASA Technical Reports Server (NTRS)

Killinger, Dennis

1992-01-01

Significant progress has been made in recent years in the development of new, solid-state laser sources. This talk will present an overview of some of the new developments in solid-state lasers, and their application toward lidar/DIAL measurements of the atmosphere. Newly emerging lasers such as Ho:YAG, Tm:YAG, OPO, and Ti:Sapphire will be covered, along with the spectroscopic parameters required for differential operational modes of atmospheric remote sensing including Doppler-Windshear lidar, Tunable laser detection of water/CO2, and broad linewidth OPO's for open path detection of pollutant hydrocarbon gases. Additional considerations of emerging laser technology for lidar/DIAL will also be covered.

Measurements of CO2 Column Abundance in the Low Atmosphere Using Ground Based 1.6 μm CO2 DIAL

NASA Astrophysics Data System (ADS)

Abo, M.; Shibata, Y.; Nagasawa, C.

2017-12-01

Changes in atmospheric carbon dioxide (CO2) concentration are believed to produce the largest radiative forcing for the current climate system. Accurate predictions of atmospheric CO2 concentration rely on the knowledge of its sinks and sources, transports, and its variability with time. Although this knowledge is currently unsatisfactory, numerical models use it as a way in simulating CO2 fluxes. Validating and improving the global atmospheric transport model, therefore, requires precise measurement of the CO2 concentration profile. There are two further variations on Lidar: the differential absorption Lidar (DIAL) and the integrated path differential absorption (IPDA) Lidar. DIAL/IPDA are basically for profile/total column measurement, respectively. IPDA is a special case of DIAL and can measure the total column-averaged mixing ratio of trace gases using return signals from the Earth's surface or from thick clouds based on an airborne or a satellite. We have developed a ground based 1.6 μm DIAL to measure vertical CO2 mixing ratio profiles from 0.4 to 2.5 km altitude. The goals of the CO2 DIAL are to produce atmospheric CO2 mixing ratio measurements with much smaller seasonal and diurnal biases from the ground surface. But, in the ground based lidar, return signals from around ground surface are usually suppressed in order to handle the large dynamic range. To receive the return signals as near as possible from ground surface, namely, the field of view (FOV) of the telescope must be wide enough to reduce the blind range of the lidar. While the return signals from the far distance are very weak, to enhance the sensitivity and heighten the detecting distance, the FOV must be narrow enough to suppress the sky background light, especially during the daytime measurements. To solve this problem, we propose a total column measurement method from the ground surface to 0.4 km altitude. Instead of strong signals from thick clouds such as the IPDA, the proposed method uses atmospheric return signals from 0.4 km altitude. Although laser outputs of two wavelengths, which are the system parameter of DIAL, are canceled, the proposed method needs to constantly monitor laser outputs. When the laser output ratio with two wavelengths is 1.0 ± 0.01, the error simulation result of the CO2 mixing ratio is 420.0 ± 3.9 ppm.

FY05 FM Dial Summary Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harper, Warren W.; Strasburg, Jana D.; Golovich, Elizabeth C.

2005-12-01

Pacific Northwest National Laboratory's Infrared Sensors team is focused on developing methods for standoff detection of nuclear proliferation. In FY05, PNNL continued the development of the FM DIAL (frequency-modulated differential absorption LIDAR) experiment. Additional improvements to the FM DIAL trailer provided greater stability during field campaigns which made it easier to explore new locations for field campaigns. In addition to the Hanford Townsite, successful experiments were conducted at the Marine Science Laboratory in Sequim, WA and the Nevada Test Site located outside Las Vegas, NV. The range of chemicals that can be detected by FM DIAL has also increased. Priormore » to FY05, distributed feedback quantum cascade lasers (DFB-QCL) were used in the FM DIAL experiments. With these lasers, only simple chemicals with narrow (1-2 cm-1) absorption spectra, such as CO2 and N2O, could be detected. Fabry-Perot (FP) QC lasers have much broader spectra (20-40 cm-1) which allows for the detection of larger chemicals and a wider array of chemicals that can be detected. A FP-QCL has been characterized and used during initial studies detecting DMMP (dimethyl methylphosphonate).« less

Survey research with a random digit dial national mobile phone sample in Ghana: Methods and sample quality.

PubMed

L'Engle, Kelly; Sefa, Eunice; Adimazoya, Edward Akolgo; Yartey, Emmanuel; Lenzi, Rachel; Tarpo, Cindy; Heward-Mills, Nii Lante; Lew, Katherine; Ampeh, Yvonne

2018-01-01

Generating a nationally representative sample in low and middle income countries typically requires resource-intensive household level sampling with door-to-door data collection. High mobile phone penetration rates in developing countries provide new opportunities for alternative sampling and data collection methods, but there is limited information about response rates and sample biases in coverage and nonresponse using these methods. We utilized data from an interactive voice response, random-digit dial, national mobile phone survey in Ghana to calculate standardized response rates and assess representativeness of the obtained sample. The survey methodology was piloted in two rounds of data collection. The final survey included 18 demographic, media exposure, and health behavior questions. Call outcomes and response rates were calculated according to the American Association of Public Opinion Research guidelines. Sample characteristics, productivity, and costs per interview were calculated. Representativeness was assessed by comparing data to the Ghana Demographic and Health Survey and the National Population and Housing Census. The survey was fielded during a 27-day period in February-March 2017. There were 9,469 completed interviews and 3,547 partial interviews. Response, cooperation, refusal, and contact rates were 31%, 81%, 7%, and 39% respectively. Twenty-three calls were dialed to produce an eligible contact: nonresponse was substantial due to the automated calling system and dialing of many unassigned or non-working numbers. Younger, urban, better educated, and male respondents were overrepresented in the sample. The innovative mobile phone data collection methodology yielded a large sample in a relatively short period. Response rates were comparable to other surveys, although substantial coverage bias resulted from fewer women, rural, and older residents completing the mobile phone survey in comparison to household surveys. Random digit dialing of mobile phones offers promise for future data collection in Ghana and may be suitable for other developing countries.

Survey research with a random digit dial national mobile phone sample in Ghana: Methods and sample quality

PubMed Central

Sefa, Eunice; Adimazoya, Edward Akolgo; Yartey, Emmanuel; Lenzi, Rachel; Tarpo, Cindy; Heward-Mills, Nii Lante; Lew, Katherine; Ampeh, Yvonne

2018-01-01

Introduction Generating a nationally representative sample in low and middle income countries typically requires resource-intensive household level sampling with door-to-door data collection. High mobile phone penetration rates in developing countries provide new opportunities for alternative sampling and data collection methods, but there is limited information about response rates and sample biases in coverage and nonresponse using these methods. We utilized data from an interactive voice response, random-digit dial, national mobile phone survey in Ghana to calculate standardized response rates and assess representativeness of the obtained sample. Materials and methods The survey methodology was piloted in two rounds of data collection. The final survey included 18 demographic, media exposure, and health behavior questions. Call outcomes and response rates were calculated according to the American Association of Public Opinion Research guidelines. Sample characteristics, productivity, and costs per interview were calculated. Representativeness was assessed by comparing data to the Ghana Demographic and Health Survey and the National Population and Housing Census. Results The survey was fielded during a 27-day period in February-March 2017. There were 9,469 completed interviews and 3,547 partial interviews. Response, cooperation, refusal, and contact rates were 31%, 81%, 7%, and 39% respectively. Twenty-three calls were dialed to produce an eligible contact: nonresponse was substantial due to the automated calling system and dialing of many unassigned or non-working numbers. Younger, urban, better educated, and male respondents were overrepresented in the sample. Conclusions The innovative mobile phone data collection methodology yielded a large sample in a relatively short period. Response rates were comparable to other surveys, although substantial coverage bias resulted from fewer women, rural, and older residents completing the mobile phone survey in comparison to household surveys. Random digit dialing of mobile phones offers promise for future data collection in Ghana and may be suitable for other developing countries. PMID:29351349

Mobile Phone Terminal

NASA Technical Reports Server (NTRS)

1978-01-01

In the photo, an employee of a real estate firm is contacting his office by means of HICOM, an advanced central terminal for mobile telephones. Developed by the Orlando Division of Martin Marietta Aerospace, Orlando, Florida, and manufactured by Harris Corporation's RF Division, Rochester, N.Y., HICOM upgrades service to users, provides better system management to telephone companies, and makes more efficient use of available mobile telephone channels through a computerized central control terminal. The real estate man, for example, was able to dial his office and he could also have direct-dialed a long distance number. Mobile phones in most areas not yet served by HICOM require an operator's assistance for both local and long distance calls. HICOM improves system management by automatically recording information on all calls for accurate billing, running continual performance checks on its own operation, and reporting any malfunctions to a central office.

Chemical contamination remote sensing

NASA Technical Reports Server (NTRS)

Carrico, J. P.; Phelps, K. R.; Webb, E. N.; Mackay, R. A.; Murray, E. R.

1986-01-01

A ground mobile laser test bed system was assembled to assess the feasibility of detection of various types of chemical contamination using Differential Scattering (DISC) and Differential Absorption (DIAL) Lidar techniques. Field experiments with the test bed system using chemical simulants were performed. Topographic reflection and range resolved DIAL detection of vapors as well as DISC detection of aerosols and surface contamination were achieved. Review of detection principles, design of the test bed system, and results of the experiments are discussed.

DARPA Emerging Technologies

DTIC Science & Technology

2016-01-01

development requires wind tunnels and ranges that do not currently exist. Furthermore, continued technology matura- tion is needed for thermal management...designed with conceptual design engine model (at existing technology level), or existing propul- sion system, or modified propulsion system (e.g...internal cameras reading gauges and dials and switch positions , directly tapping into current or future avion- ics service buses and integrating

Investigation of potential of differential absorption Lidar techniques for remote sensing of atmospheric pollutants

NASA Technical Reports Server (NTRS)

Butler, C. F.; Shipley, S. T.; Allen, R. J.

1981-01-01

The NASA multipurpose differential absorption lidar (DIAL) system uses two high conversion efficiency dye lasers which are optically pumped by two frequency-doubled Nd:YAG lasers mounted rigidly on a supporting structure that also contains the transmitter, receiver, and data system. The DIAL system hardware design and data acquisition system are described. Timing diagrams, logic diagrams, and schematics, and the theory of operation of the control electronics are presented. Success in obtaining remote measurements of ozone profiles with an airborne systems is reported and results are analyzed.

Multiple volatile organic compound vapor chamber testing with a frequency-agile CO2 DIAL system: field-test results

NASA Astrophysics Data System (ADS)

Carr, Lewis W.; Warren, Russell E.; Carlisle, Clinton B.; Carlisle, Sylvie A.; Cooper, David E.; Fletcher, Leland; Gotoff, Steven W.; Reyes, Felix

1995-02-01

Many of the 189 hazardous air pollutants (HAPs) listed in the Environmental Protection Agency regulations can be monitored by frequency agile CO2 DIAL (FACD) systems. These systems can be used to survey industrial and military installations and toxic waste repositories at ranges of a few kilometers from emission sources. FACD systems may become a valuable tool for detection and estimation of a wide array of HAPs. However, in most cases, several of the listed HAPs will be present simultaneously and discrimination of one HAP from another based on differences in spectral characteristics can be challenging for FACD systems. While FACD hardware is mature and is capable of addressing these discrimination issues, multiple-contaminate separation algorithms need to be developed. A one week field test was conducted at Los Banos, California, to gather multiple HAP data that will be used for future algorithm development. A vapor chamber was used to control disseminated concentrations of each HAP and reduce effects of atmospheric turbulence and wind direction and speed. Data was collected for several chemicals injected into the vapor chamber simultaneously. The data and results from the field test are presented and calibration issues are discussed.

Fieldable Fourier transform spectrometer

NASA Astrophysics Data System (ADS)

Hatchell, Brian K.; Harper, Warren W.; Schultz, John F.

2004-10-01

The infrared sensors group at the Pacific Northwest National Laboratory (PNNL) is focused on the science and technology of remote and in-situ chemical sensors for detecting proliferation and countering terrorism. To support these vital missions, PNNL is developing frequency-modulation techniques for remote probing over long optical paths by means of differential-absorption light detecting and ranging (LIDAR). This technique can easily monitor large areas, or volumes, that could only be accomplished with a large network of point sensors. Recently, PNNL began development of a rugged frequency-modulation differential-abosrption LIDAR (FM-DIAL) system to conduct field experiments. To provide environmentla protection for the system and facilitate field deployments and operations, a large, well insulated, temperature controlled trailer was specified and acquired. The trailer was outfitted with a shock-mounted optical bench, an electronics rack, a liquid nitrogen Dewar, and a power generator. A computer-controlled gimbal-mounted mirror was added to allow the telescope beam to be accurately pointed in both the vertical and horizontal plane. This turned out to be the most complicated addition, and is described in detail. This paper provides an overview of the FM-DIAL system and illustrates innovative solutions developed to overcome several alignment and stability issues encountered in the field.

Ozone Measurements with the US EPA UV-DIAL: Preliminary Results

NASA Technical Reports Server (NTRS)

Moosmueller, H.; Diebel, D.; Bundy, D. H.; Bristow, M. P.; Alvarez, R. J., II; Kovalev, V. A.; Edmonds, C. M.; Turner, R. M.; Mcelroy, J. L.

1992-01-01

A compact airborne down-looking lidar system was developed at the Environmental Protection Agency in Las Vegas. This differential absorption lidar (DIAL) was designed to simultaneously measure range-resolved concentrations of ozone (O3) and sulfur dioxide (SO2) in the lower troposphere, together with an indication of the aerosol distribution. The five laser wavelengths (i.e., lambda(sub 1) = 277 nm, lambda(sub 2) = 292 nm, lambda(sub 3) = 313 nm, lambda(sub4) = 319 nm, lambda(sub 5) = 369 nm) were generated via Raman conversion of a focused KrF excimer laser. The system is currently installed in a truck-based mobile laboratory. For the ground testing, an opening in the truck floor together with a folding mirror under the truck makes a horizontal, or upwardly inclined direction of measurement possible. Initial ground testing has been performed in the vicinity of a Desert Research Institute (DRI) ambient air monitoring site, located at Cottonwood Cove approximately 85 km south east of Las Vegas, Nevada. At this site O3 and SO2 concentrations are continuously monitored with an average accuracy better than +/- 10 percent. A temporary ozone measurement station with identical accuracy was set up at a distance to get a second point of comparison for the range-resolved DIAL measurements.

Detection and monitoring of pollutant sources with Lidar/Dial techniques

NASA Astrophysics Data System (ADS)

Gaudio, P.; Gelfusa, M.; Malizia, A.; Parracino, S.; Richetta, M.; De Leo, L.; Perrimezzi, C.; Bellecci, C.

2015-11-01

It's well known that air pollution due to anthropogenic sources can have adverse effects on humans and the ecosystem. Therefore, in the last years, surveying large regions of the atmosphere in an automatic way has become a strategic objective of various public health organizations for early detection of pollutant sources in urban and industrial areas. The Lidar and Dial techniques have become well established laser based methods for the remote sensing of the atmosphere. They are often implemented to probe almost any level of the atmosphere and to acquire information to validate theoretical models about different topics of atmospheric physics. They can also be used for environment surveying by monitoring particles, aerosols and molecules. The aim of the present work is to demonstrate the potential of these methods to detect pollutants emitted from local sources (such as particulate and/or chemical compounds) and to evaluate their concentration. This is exemplified with the help of experimental data acquired in an industrial area in the south of Italy by mean of experimental campaign by use of pollutants simulated source. For this purpose, two mobile systems Lidar and Dial have been developed by the authors. In this paper there will be presented the operating principles of the system and the results of the experimental campaign.

A new frontier in CO2 flux measurements using a highly portable DIAL laser system

PubMed Central

Queiβer, Manuel; Granieri, Domenico; Burton, Mike

2016-01-01

Volcanic CO2 emissions play a key role in the geological carbon cycle, and monitoring of volcanic CO2 fluxes helps to forecast eruptions. The quantification of CO2 fluxes is challenging due to rapid dilution of magmatic CO2 in CO2-rich ambient air and the diffuse nature of many emissions, leading to large uncertainties in the global magmatic CO2 flux inventory. Here, we report measurements using a new DIAL laser remote sensing system for volcanic CO2 (CO2DIAL). Two sites in the volcanic zone of Campi Flegrei (Italy) were scanned, yielding CO2 path-amount profiles used to compute fluxes. Our results reveal a relatively high CO2 flux from Campi Flegrei, consistent with an increasing trend. Unlike previous methods, the CO2DIAL is able to measure integrated CO2 path-amounts at distances up to 2000 m using virtually any solid surface as a reflector, whilst also being highly portable. This opens a new frontier in quantification of geological and anthropogenic CO2 fluxes. PMID:27652775

Lidar/DIAL detection of acetone at 3.3 μm by a tunable OPO laser system

NASA Astrophysics Data System (ADS)

Puiu, A.; Fiorani, L.; Rosa, O.; Borelli, R.; Pistilli, M.; Palucci, A.

2014-08-01

In this paper we report, for the first time to our knowledge, on lidar/DIAL detection of acetone vapors at 3.3 μm by means of an optical parametric tunable laser system. After a preliminary spectroscopic study in an absorption cell, the feasibility of a differential absorption (DIAL) lidar for the detection of acetone vapors has been investigated in the laboratory, simulating the experimental conditions of a field campaign. Having in mind measurements in a real scenario, a study of possible atmospheric intereferents has been performed, looking for all known compounds that share acetone IR absorption in the spectral band selected for its detection. Possible interfering species from urban and industrial atmospheres were investigated and limits of acetone detection in both environments were identified. This study confirmed that a lidar system can detect a low concentration of acetone at considerable distances.

Application of a CO2 dial system for infrared detection of forest fire and reduction of false alarm

NASA Astrophysics Data System (ADS)

Bellecci, C.; Francucci, M.; Gaudio, P.; Gelfusa, M.; Martellucci, S.; Richetta, M.; Lo Feudo, T.

2007-04-01

Forest fires can be the cause of serious environmental and economic damages. For this reason considerable effort has been directed toward forest protection and fire fighting. The means traditionally used for early fire detection mainly consist in human observers dispersed over forest regions. A significant improvement in early warning capabilities could be obtained by using automatic detection apparatus. In order to early detect small forest fires and minimize false alarms, the use of a lidar system and dial technique will be considered. A first evaluation of the lowest detectable concentration will be estimated by numerical simulation. The theoretical model will also be used to get the capability of the dial system to control wooded areas. Fixing the burning rate for several fuels, the maximum range of detection will be evaluated. Finally results of simulations will be reported.

Inexpensive automated paging system for use at remote research sites

USGS Publications Warehouse

Sargent, S.L.; Dey, W.S.; Keefer, D.A.

1998-01-01

The use of a flow-activated automatic sampler at a remote research site required personnel to periodically visit the site to collect samples and reset the automatic sampler. To reduce site visits, a cellular telephone was modified for activation by a datalogger. The purpose of this study was to demonstrate the use and benefit of the modified telephone. Both the power switch and the speed-dial button on the telephone were bypassed and wired to a relay driver. The datalogger was programmed to compare values of a monitored environmental parameter with a target value. When the target value was reached or exceeded, the datalogger pulsed a relay driver, activating power to the telephone. A separate relay activated the speed dial, dialing the number of a tone-only pager. The use of this system has saved time and reduced travel costs by reducing the number of trips to the site, without the loss of any data.The use of a flow-activated automatic sampler at a remote research site required personnel to periodically visit the site to collect samples and reset the automatic sampler. To reduce site visits, a cellular telephone was modified for activation by a datalogger. The purpose of this study was to demonstrate the use and benefit of the modified telephone. Both the power switch and the speed-dial button on the telephone were bypassed and wired to a relay driver. The datalogger was programmed to compare values of a monitored environmental parameter with a target value. When the target value was reached or exceeded, the datalogger pulsed a relay driver, activating power to the telephone. A separate relay activated the speed dial, dialing the number of a tone-only pager. The use of this system has saved time and reduced travel costs by reducing the number of trips to the site, without the loss of any data.

Diode injection - seeded, 940 nanometer (nm), titanium - sapphire laser for H2O DIAL (differential absorption lidar), measurements

NASA Technical Reports Server (NTRS)

Miller, George E.

1992-01-01

Differential absorption of laser radiation by various molecular species represents both a selective and a sensitive method of measuring specific atmospheric constituents. DIAL measurements can be carried out via two different means. Both involve using two laser pulses with slightly different wavelengths (lambda), (one lambda at a strong absorption line of the molecule of interest, the other detuned into the wing of the line), and comparing the attenuation of the pulses. One approach relies on scattering of the radiation from some conveniently located topographical target. In the other technique elastic scattering from atmospheric aerosols and particulates is used to return the radiation to the lidar receiver system. This case is referred to as the differential absorption and scattering technique, and is the technique we are interested in to measure water vapor at 940 nm. The 940 nm wavelength is extremely desirable to atmospheric scientist interested in accurate DIAL measurements of H2O in the upper and lower troposphere. Simulated measurements using approximately 940 nm and 815 nm lasers at a range of altitudes and experimental conditions are shown. By offering access to larger absorption cross-sections, injected seeded, 940 nm DIAL laser transmitters would allow for more accurate water profile measurements at altitudes from 6 to 16 km than is currently possible with 730 nm and 815 nm DIAL laser transmitters. We have demonstrated the operation of an injected seeded titanium-sapphire (TS) laser operating at approximately 940 nm with an energy of more than 90 mJ per pulse. The TS laser is pumped by a commercial, 600 mJ, 532 nm, 10 Hz Nd:YAG laser. The slope efficiency of the laser using a flat 50 percent R output coupler and a 10 m end-mirror is shown. The laser was injected seeded with a CW, AlGaAs, semiconductor diode laser which had an output of 83 mW. The CW diode seed beam was introduced into the TS laser cavity through a HR end-mirror. When the diode beam is aligned to the TS resonator, it controls the TS laser output wavelength and its spectral line width with the required resolution for DIAL applications. This work supports the need for the development of 940 nm, titanium-sapphire DIAL transmitters.

First open field measurements with a portable CO2 lidar/dial system for early forest fires detection

NASA Astrophysics Data System (ADS)

Gaudio, Pasquale; Gelfusa, Michela; Lupelli, Ivan; Malizia, Andrea; Moretti, Alessandro; Richetta, Maria; Serafini, Camilla; Bellecci, Carlo

2011-11-01

Lidar and dial are well established methods to explore the atmosphere. Different groups have already shown experimentally the possibility to measure the density variation of aerosol and particulate in the atmosphere due to plumes emitted in forest fires with this kind of systems. The aim of the present work is to demonstrate the capabilities of our mobile Lidar system, based on a CO2 laser, to detect forest fires and minimizing false alarms. For this purpose, our system can be operated in both lidar and dial configurations in sequence. The first Lidar measurement is performed to evaluate the variation of the local density into the atmosphere, using a nonabsorption water wavelength 10R18 (10.571 μm). If the returned signal reports a backscattering peak, the presence of a fire is probable. To confirm this hypothesis, a second dial measurement is carried out to reveal a second component emitted during the combustion process. The chosen second component is water vapour, which is, as it is well-known, largely produced during the first combustion stage. Measuring the water concentration peak after the detection of the aerosol density increment (referred to the standard mean atmospheric value) represents a good method to reduce false alarms with a dial system. In order to test this methodology, a first set of measurements has been performed in a field near the Engineering Faculty of the University of Rome "Tor Vergata". A quite small controlled-fire has been lighted into a box at a distance of about one kilometre from the system. The data acquired at the two wavelengths (10R18 and 10R20) have been averaged on 100 elastic backscattered Lidar signals. The first results confirm the effectiveness of the measurement strategy for reducing the number of false alarm preserving the early detection.

The use of a robotic tibial rotation device and an electromagnetic tracking system to accurately reproduce the clinical dial test.

PubMed

Stinton, S K; Siebold, R; Freedberg, H; Jacobs, C; Branch, T P

2016-03-01

The purpose of this study was to: (1) determine whether a robotic tibial rotation device and an electromagnetic tracking system could accurately reproduce the clinical dial test at 30° of knee flexion; (2) compare rotation data captured at the footplates of the robotic device to tibial rotation data measured using an electromagnetic sensor on the proximal tibia. Thirty-two unilateral ACL-reconstructed patients were examined using a robotic tibial rotation device that mimicked the dial test. The data reported in this study is only from the healthy legs of these patients. Torque was applied through footplates and was measured using servomotors. Lower leg motion was measured at the foot using the motors. Tibial motion was also measured through an electromagnetic tracking system and a sensor on the proximal tibia. Load-deformation curves representing rotational motion of the foot and tibia were compared using Pearson's correlation coefficients. Off-axis motions including medial-lateral translation and anterior-posterior translation were also measured using the electromagnetic system. The robotic device and electromagnetic system were able to provide axial rotation data and translational data for the tibia during the dial test. Motion measured at the foot was not correlated to motion of the tibial tubercle in internal rotation or in external rotation. The position of the tibial tubercle was 26.9° ± 11.6° more internally rotated than the foot at torque 0 Nm. Medial-lateral translation and anterior-posterior translation were combined to show the path of the tubercle in the coronal plane during tibial rotation. The information captured during a manual dial test includes both rotation of the tibia and proximal tibia translation. All of this information can be captured using a robotic tibial axial rotation device with an electromagnetic tracking system. The pathway of the tibial tubercle during tibial axial rotation can provide additional information about knee instability without relying on side-to-side comparison between knees. The translation of the proximal tibia is important information that must be considered in addition to axial rotation of the tibia when performing a dial test whether done manually or with a robotic device. Instrumented foot position cannot provide the same information. IV.

Development of Double and Triple-Pulsed 2-micron IPDA Lidars for Column CO2 Measurements

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Yu, Jirong; Petros, Mulugeta; Refaat, Tamer F.; Remus, Ruben G.; Reithmaier, Karl

2015-01-01

Carbon dioxide (CO2) is an important greenhouse gas that significantly contributes to the carbon cycle and globalradiation budget on Earth. CO2 role on Earth’s climate is complicated due to different interactions with various climatecomponents that include the atmosphere, the biosphere and the hydrosphere. Although extensive worldwide efforts formonitoring atmospheric CO2 through various techniques, including in-situ and passive sensors, are taking place highuncertainties exist in quantifying CO2 sources and sinks. These uncertainties are mainly due to insufficient spatial andtemporal mapping of the gas. Therefore it is required to have more rapid and accurate CO2 monitoring with higheruniform coverage and higher resolution. CO2 DIAL operating in the 2-µm band offer better near-surface CO2measurement sensitivity due to the intrinsically stronger absorption lines. For more than 15 years, NASA LangleyResearch Center (LaRC) contributed in developing several 2-?m CO2 DIAL systems and technologies. This paperfocuses on the current development of the airborne double-pulsed and triple-pulsed 2-?m CO2 integrated pathdifferential absorption (IPDA) lidar system at NASA LaRC. This includes the IPDA system development andintegration. Results from ground and airborne CO2 IPDA testing will be presented. The potential of scaling suchtechnology to a space mission will be addressed.

Design of Instrument Dials for Maximum Legibility: 1. Development of Methodology and Some Preliminary Results

DTIC Science & Technology

1947-10-20

Peyohology Lehlgh University Bothlehea, mnnsylvania Attni nr. Adalbert Ford nepmrtmnnt of Psychology University of Maryland College Park, Maryland...light sources consi-itcd of Mazda lamps In cans* The sample dial was so illuminated that the w’.iii.e markings were 5 foot lamberta on • background

Development of an Intelligent Monitoring System for Geological Carbon Sequestration (GCS) Systems

NASA Astrophysics Data System (ADS)

Sun, A. Y.; Jeong, H.; Xu, W.; Hovorka, S. D.; Zhu, T.; Templeton, T.; Arctur, D. K.

2016-12-01

To provide stakeholders timely evidence that GCS repositories are operating safely and efficiently requires integrated monitoring to assess the performance of the storage reservoir as the CO2 plume moves within it. As a result, GCS projects can be data intensive, as a result of proliferation of digital instrumentation and smart-sensing technologies. GCS projects are also resource intensive, often requiring multidisciplinary teams performing different monitoring, verification, and accounting (MVA) tasks throughout the lifecycle of a project to ensure secure containment of injected CO2. How to correlate anomaly detected by a certain sensor to events observed by other devices to verify leakage incidents? How to optimally allocate resources for task-oriented monitoring if reservoir integrity is in question? These are issues that warrant further investigation before real integration can take place. In this work, we are building a web-based, data integration, assimilation, and learning framework for geologic carbon sequestration projects (DIAL-GCS). DIAL-GCS will be an intelligent monitoring system (IMS) for automating GCS closed-loop management by leveraging recent developments in high-throughput database, complex event processing, data assimilation, and machine learning technologies. Results will be demonstrated using realistic data and model derived from a GCS site.

An Overview of Communications Technology and Development Efforts for 2015 SBIR Phase I

NASA Technical Reports Server (NTRS)

Nguyen, Hung D.; Steele, Gynelle C.

2017-01-01

This report highlights innovative SBIR 2015 Phase I projects specifically addressing areas in Communications Technology and Development which is one of six core competencies at NASA Glenn Research Center. There are fifteen technologies featured with emphasis on a wide spectrum of applications such as novel solid state lasers for space-based water vapor dial; wide temperature, high voltage and energy density capacitors for aerospace exploration; instrument for airborne measurement of carbonyl sulfide; high-power tunable seed laser for methane Lidar transmitter; ROC-rib deployable ka-band antenna for nanosatellites; a SIC-based microcontroller for high-temperature in-situ instruments and systems; improved yield, performance and reliability of high-actuator-count deformable mirrors; embedded multifunctional optical sensor system; switching electronics for space-based telescopes with advanced AO systems; integrated miniature DBR laser module for Lidar instruments; and much more. Each article in this booklet describes an innovation, technical objective, and highlights NASA commercial and industrial applications. space-based water vapor dial; wide temperature, high voltage and energy density capacitors foraerospace exploration; instrument for airborne measurement of carbonyl sulfide; high-power tunable seed laser formethane Lidar transmitter; ROC-rib deployable ka-band antenna for nanosatellites.

Airborne Dial Remote Sensing of the Arctic Ozone Layer

NASA Technical Reports Server (NTRS)

Wirth, Martin; Renger, Wolfgang; Ehret, Gerhard

1992-01-01

A combined ozone and aerosol LIDAR was developed at the Institute of Physics of the Atmosphere at the DLR in Oberpfaffenhofen. It is an airborne version, that, based on the DIAL-principle, permits the recording of two-dimensional ozone profiles. This presentation will focus on the ozone-part; the aerosol subsection will be treated later.

Advances in High Energy Solid-State 2-micron Laser Transmitter Development for Ground and Airborne Wind and CO2 Measurements

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Yu, Jirong; Petros, Mulugeta; Chen, Songsheng; Kavaya, Michael J.; Trieu, Bo; Bai, Yingxin; Petzar, Paul; Modlin, Edward A.; Koch, Grady;

Dial Measurements of Free-Tropospheric Ozone Profiles in Huntsville, AL

NASA Technical Reports Server (NTRS)

Newchurch, Mike; Kuang, Shi; Burris, John; Johnson, Steve; Long, Stephanie

2008-01-01

A tropospheric ozone DIfferential Absorption Lidar (DIAL) system has been developed jointly by NASA and the University of Alabama at Huntsville (UAH). Two separated Nd:YAG pumped dye laser systems produce the laser pulses with wavelengths of 285 and 291 nm at 20 Hz frequency. The receiver is a Newtonian telescope with a 40 cm primary and a two-channel aft optics unit. The detection system currently uses photon counting to facilitate operations at the maximum achievable altitude. This lidar measures free-tropospheric ozone profiles between 4-10 km at Regional Atmospheric Profiling Laboratory for Discovery (RAPCD) in UAH campus (ASL 206 m) under both daytime and nighttime conditions. Frequent coincident ozonesonde flights and theoretical calculations provide evidence to indicate the retrieval accuracy ranges from approx.5% at 4 km to approx.60% at 10 km with 750-m vertical resolution and 30-minute integration. Three Hamamatsu 7400 PMTs and analog detection technique will be added on the current system to extend the measurement to approx.100 m above ground to monitor the PBL and lower tropospheric ozone variations.

Development of an Eye-Safe Micro-Pulse Differential Absorption Lidar (DIAL) for Carbon Dioxide Profilings

NASA Astrophysics Data System (ADS)

Johnson, W.; Repasky, K. S.; Nehrir, A. R.; Carlsten, J.

2011-12-01

A differential absorption lidar (DIAL) for monitoring carbon dioxide (CO2) is under development at Montana State University using commercially available parts. Two distributed feedback (DFB) lasers, one at the on-line wavelength and one at the off-line wavelength are used to injection seed a fiber amplifier. The DIAL operates in the 1.57 micron carbon dioxide absorption band at an on-line wavelength of 1.5714060 microns. The laser transmitter produces 40 μJ pulses with a pulse duration of 1 μs and a pulse repetition frequency of 20 kHz. The scattered light from the laser transmitter is collected using a 28 cm diameter Schmidt-Cassegrain telescope. The light collected by the telescope is collimated and then filtered using a 0.8 nm FWHM narrowband interference filter. After the optical filter, the light is coupled into a multimode optical fiber with a 1000 μm core diameter. The output from the optical fiber is coupled into a photomultiplier tube (PMT) used to monitor the return signal. The analog output from the PMT is next incident on a discriminator producing TTL logic pulses for photon counting. The output from the PMT and discriminator is monitored using a multichannel scalar card allowing the counting of the TTL pulses as a function of range. Data from the DIAL instrument is collected in the following manner. The fiber amplifier is injection seeded first with the on-line DFB laser. The return signal as a function of range is integrated using the multichannel scalar for a user defined time, typically set at 6 s. The off-line DFB laser is then used to injection seed the fiber amplifier and the process is repeated. This process is repeated for a user defined period. The CO2 concentration as a function of range is calculated using the on-line and off-line return signals with the DIAL equation. A comparison of the CO2 concentration measured using the DIAL instrument at 1.5 km and a Li-Cor LI-820 in situ sensor located at 1.5 km from the DIAL over a 2.5 hour period indicate that the CO2 DIAL has an accuracy of ±20 parts per million (PPM).

Development of an Airborne Micropulse Water Vapor DIAL

NASA Astrophysics Data System (ADS)

Nehrir, A. R.; Ismail, S.

2012-12-01

Water vapor plays a key role in many atmospheric processes affecting both weather and climate. Airborne measurements of tropospheric water vapor profiles have been a longstanding observational need to not only the active remote sensing community but also to the meteorological, weather forecasting, and climate/radiation science communities. Microscale measurements of tropospheric water vapor are important for enhancing near term meteorological forecasting capabilities while mesoscale and synopticscale measurements can lead to an enhanced understanding of the complex coupled feedback mechanisms between water vapor, temperature, aerosols, and clouds. To realize tropospheric measurements of water vapor profiles over the microscale-synopticscale areas of meteorological interest, a compact and cost effective airborne micropulse differential absorption lidar (DIAL) is being investigated using newly emerging semiconductor based laser technology. Ground based micropulse DIAL (MPD) measurements of tropospheric water vapor and aerosol profiles up to 6 km and 15 km, respectively, have been previously demonstrated using an all semiconductor based laser transmitter. The DIAL transmitter utilizes a master oscillator power amplifier (MOPA) configuration where two semiconductor seed lasers are used to seed a single pass traveling wave tapered semiconductor optical amplifier (TSOA), producing up to 7μJ pulse energies over a 1 μs pulse duration at a 10 kHz pulse repetition frequency (PRF). Intercomparisons between the ground based instrument measurements and radiosonde profiles demonstrating the MPD performance under varying atmospheric conditions will be presented. Work is currently ongoing to expand upon the ground based MPD concept and to develop a compact and cost effective system capable of deployment on a mid-low altitude aircraft such as the NASA Langley B200 King Air. Initial lab experiments show that a two-three fold increase in the laser energy compared to the ground based instrument is achievable via overdriven current pulses to the TSOA gain medium while maintaining a 1μs and 10 kHz pulse width and PRF, respectively. The increase in the laser transmitter pulse energy will allow for nighttime and daytime water vapor profile retrievals from an airborne platform operating at an 8 km altitude with 2-5 minute integration periods. Results from a numerical model demonstrating the performance of an airborne DIAL system with the mentioned transmitter enhancements will be presented and compared against the existing ground based instrument performance. Furthermore, results from laboratory experiments demonstrating the laser transmitter performance including maximum extractable energy, energy stability, and spectral purity will also be presented.

Design and implementation of telephone dialer based on Arduino

NASA Astrophysics Data System (ADS)

Ma, Zilong; Lei, Ying

2017-03-01

Introduces a system design scheme of the telephone dialer based on Arduino, including the design principle, hardware and software design and the experimental results in this paper. The scheme is based on the dual tone multi frequency (DTMF) dialing mode, using the Arduino UNO as the main controller, the serial port send out the telephone number to be dialed, speaker synthesize the voice.

Development and Testing of a Scanning Differential Absorption Lidar For Carbon Sequestration Site Monitoring

NASA Astrophysics Data System (ADS)

Soukup, B.; Johnson, W.; Repasky, K. S.; Carlsten, J. L.

2013-12-01

A scanning differential absorption lidar (DIAL) instrument for carbon sequestration site monitoring is under development and testing at Montana State University. The laser transmitter uses two tunable discrete mode laser diodes (DMLD) operating in the continuous wave (cw) mode with one locked to the on-line absorption wavelength at 1571.4067 nm and the second operating at the off-line wavelength at 1571.2585 nm. Two in-line fiber optic switches are used to switch between on-line and off-line operation. After the fiber optic switches, an acousto-optic modulator (AOM) is used to generate a pulse train used to injection seed an erbium doped fiber amplifier (EDFA) to produce eye-safe laser pulses with maximum pulse energies of 66 J and a pulse repetition frequency of 15 kHz. The DIAL receiver uses a 28 cm diameter Schmidt-Cassegrain telescope to collect that backscattered light, which is then monitored using a fiber coupled photo-multiplier tube (PMT) module operating in the photon counting mode. The PMT has a 3% quantum efficiency, a dark count rate of 90 kHz, and a maximum count rate of 1 MHz. Recently, a fiber coupled avalanche photodiode (APD) operating in the geiger mode has been incorporated into the DIAL receiver. The APD has a quantum efficiency of 10%, a dark count rate of 10 kHz, and a maximum count rate of 1 MHz and provides a much larger dynamic range than the PMT. Both the PMT and APD provide TTL logic pulses that are monitored using a multichannel scaler card used to count the return photons as a function of time of flight and are thus interchangeable. The DIAL instrument was developed at the 1.571 m wavelength to take advantage of commercial-off-the-shelf components. The instrument is operated using a custom Labview program that switches to the DMLD operating at the on-line wavelength, locks this laser to a user defined wavelength setting, and collects return signals for a user defined time. The control program switches to the DMLD operating at the off-line wavelength where data is again collected for a user defined time. The control program repeats this process until stopped by the operator. The DIAL instrument has been operated at the Zero Emission Research Technology (ZERT) field site located on the Montana State University campus and at the Big Sky Carbon Sequestration Partnership site located in north-central Montana. Data collected by the DIAL instrument at both field sites demonstrate that the DIAL is capable of retrieving night time CO2 number density profiles out to a range of 2.5 km with a 150 m range resolution. The DIAL retrievals are validated using a co-located Li-COR 820 gas analyzer placed along the DIAL optical path allowing comparison at a single range as a function of time.

Pornography and Sexual Aggression

DTIC Science & Technology

1991-01-01

Dial-a- Porn .......................................8a Videocassettes.................................... 9 Pornographic Magazines...well known pornographic film, DeeR Throat, cost only M25,000 to produce, and has earned more than $50 million in profits.10 DIAL-A- PORN Dial-a- Porn has...Estimated costs for establishing a twenty-five dial-a- porn utility, including advertising, is $25,000.1 1 A typical dial-a- porn recording delivers an

Introduction to the concepts of TELEDEMO and TELEDIMS

NASA Technical Reports Server (NTRS)

Rice, R. F.; Schlutsmeyer, A. P.

1982-01-01

An introduction to the system concepts: TELEDEMO and TELEDIMS is provided. TELEDEMO is derived primarily from computer graphics and, via incorporation of sophisticated image data compression, enables effective low cost teleconferencing at data rates as low as 1K bit/second using dial-up phone lines. Combining TELEDEMO's powerful capabilities for the development of presentation material with microprocessor-based Information Management Systems (IMS) yields a truly all electronic IMS called TELEDIMS.

Real Time Baseball Database

NASA Astrophysics Data System (ADS)

Fukue, Yasuhiro

The author describes the system outline, features and operations of "Nikkan Sports Realtime Basaball Database" which was developed and operated by Nikkan Sports Shimbun, K. K. The system enables to input numerical data of professional baseball games as they proceed simultaneously, and execute data updating at realtime, just-in-time. Other than serving as supporting tool for prepareing newspapers it is also available for broadcasting media, general users through NTT dial Q2 and others.

County Community Development Studies. No. 2: Extensions Library on Tape, Sarasota County.

ERIC Educational Resources Information Center

Rozar, Luther L.; And Others

A study was conducted in Sarasota County, Florida, to determine the feasibility of implementing a County Extension Service library on telecassette tape that could be dialed by phone callers. The system would allow office callers access to two-to-three-minute tape recordings containing information on many common problems. A survey instrument…

Development and operation of a real-time data acquisition system for the NASA, Langley Research Center Differential Absorption Lidar

NASA Technical Reports Server (NTRS)

Butler, C.; Kindle, E. C.

1984-01-01

The capabilities of the DIAL data acquisition system (DAS) for the remote measurement of atmospheric trace gas concentrations from ground and aircraft platforms were extended through the purchase and integration of other hardware and the implementation of improved software. An operational manual for the current system is presented. Hardware and peripheral device registers are outlined only as an aid in debugging any DAS problems which may arise.

DIAL Measurements of Free-Tropospheric Ozone Profiles in Huntsville, AL

NASA Technical Reports Server (NTRS)

Kuang, Shi; Burris, John; Newchurch, Michael J.; Johnson, Steve

2007-01-01

A tropospheric ozone Differential Absorption Lidar (DIAL) system, developed jointly by NASA and the University of Alabama at Huntsville (UAH), measures free-tropospheric ozone profiles between 4-10 km. Located at 192 meters altitude in the Regional Atmospheric Profiling Laboratory for Discovery (RAPCD) on the UAH campus in Huntsville, AL, USA, this tropospheric ozone lidar operates under both daytime and nighttime conditions. Frequent coincident ozonesonde flights and theoretical calculations provide evidence to indicate the retrieval accuracy ranges from better than 8% at 4km to 40%-60% at 10 kin with 750-m vertical resolution and 30-minute integration. With anticipated improvements to allow retrievals at both higher and lower altitudes, this ozone lidar, along with co-located aerosol and Doppler Wind Lidars, will provide a unique 18 dataset for investigations of PBL and free-tropospheric chemical and dynamic processes.

Improvement of the matching speed of AIMS for development of an automatic totally tuning system for hyperthermia treatment using a resonant cavity applicator.

PubMed

Shindo, Y; Kato, K; Tsuchiya, K; Hirashima, T; Suzuki, M

2009-01-01

In this paper, we discuss the improvement of the speed of AIMS (Automatic Impedance Matching System) to automatically make impedance matching for a re-entrant resonant cavity applicator for non-invasive deep brain tumors hyperthermia treatments. We have already discussed the effectiveness of the heating method using the AIMS, with experiments of heating agar phantoms. However, the operating time of AIMS was about 30 minutes. To develop the ATT System (Automatic Totally Tuning System) including the automatic frequency tuning system, we must improve this problem. Because, when using the ATTS, the AIMS is used repeatedly to find the resonant frequency. In order to improve the speed of impedance matching, we developed the new automatic impedance matching system program (AIMS2). In AIMS, the stepping motors were connected to the impedance matching unit's dials. These dials were turned to reduce the reflected power. AIMS consists of two phases: all range searching and detailed searching. We focused on the three factors affecting the operating speed and improved them. The first factor is the interval put between the turning of the motors and AD converter. The second factor is how the steps of the motor when operating all range searching. The third factor is the starting position of the motor when detail searching. We developed the simple ATT System (ATT-beta) based on the AIMS2. To evaluate the developed AIMS2 and ATT- beta, experiments with an agar phantom were performed. From these results, we found that the operating time of the AIMS2 is about 4 minutes, which was approximately 12% of AIMS. From ATT-beta results, it was shown that it is possible to tune frequency and automatically match impedance with the program based on the AIMS2.

Remote sensing of air pollution over large European cities by lidar

NASA Astrophysics Data System (ADS)

Koelsch, Hans J.; Kolenda, Juergen; Rairoux, Patrick; Stein, Bernhard; Weidauer, Dirk; Wolf, Jean-Pierre; Woeste, Ludger H.; Fritzsche, Klaus

1993-09-01

Progresses in remote sensing of the atmosphere using the Udar (Light detection and ranging) technique closely follows progresses in Laser technology. We developed a mobile DIAL (differential absorption Lidar) system, based on high repetition rate Excimerpumped dye lasers, for performing 2D and 3D-mappings of concentration of NO, N02, S02, and 03. The high sensitivity of the system has been used for numerous environmental studies and measurement campaigns, providing for the first time a direct correlation between emission and immission. Attractive results have been obtained under urban conditions, because of the presence of strong concentration gradients, and fast fluctuations due to traffic. A comparative study between Lyon, Stuttgart, Geneva and Berlin will be presented. In particular, the Berlin-campaign demonstrates the possibility of detecting unknown emitters and monitoring exportation-importation processes of atmospheric pollution. A new stationary DIAL system has been recently constructed and implemented on the top of a building in the center of the city Leipzig. It will routinely perform concentration mappings of nitrogen oxides, sulfur dioxide and ozone, giving access to long term evolution of pollution distributions.

Lidar/DIAL detection of bomb factories

NASA Astrophysics Data System (ADS)

Fiorani, Luca; Puiu, Adriana; Rosa, Olga; Palucci, Antonio

2013-10-01

One of the aims of the project BONAS (BOmb factory detection by Networks of Advanced Sensors) is to develop a lidar/DIAL (differential absorption lidar) to detect precursors employed in the manufacturing of improvised explosive devices (IEDs). At first, a spectroscopic study has been carried out: the infrared (IR) gas phase spectrum of acetone, one of the more important IED precursors, has been procured from available databases and checked with cell measurements. Then, the feasibility of a lidar/DIAL for the detection of acetone vapors has been shown in laboratory, simulating the experimental conditions of a field campaign. Eventually, having in mind measurements in a real scenario, an interferent study has been performed, looking for all known compounds that share with acetone IR absorption in the spectral band selected for its detection. Possible interfering species were investigated, simulating both urban and industrial atmospheres and limits of acetone detection in both environments were identified. This study confirmed that a lidar/DIAL can detect low concentration of acetone at considerable distances.

Airborne lidar mapping of vertical ozone distributions in support of the 1990 Clean Air Act Amendments

NASA Technical Reports Server (NTRS)

Uthe, Edward E.; Nielsen, Norman B.; Livingston, John M.

1992-01-01

The 1990 Clean Air Act Amendments mandated attainment of the ozone standard established by the U.S. Environmental Protection Agency. Improved photochemical models validated by experimental data are needed to develop strategies for reducing near surface ozone concentrations downwind of urban and industrial centers. For more than 10 years, lidar has been used on large aircraft to provide unique information on ozone distributions in the atmosphere. However, compact airborne lidar systems are needed for operation on small aircraft of the type typically used on regional air quality investigations to collect data with which to develop and validate air quality models. Data presented in this paper will consist of a comparison between airborne differential absorption lidar (DIAL) and airborne in-situ ozone measurements. Also discussed are future plans to improve the airborne ultraviolet-DIAL for ozone and other gas observations and addition of a Fourier Transform Infrared (FTIR) emission spectrometer to investigate the effects of other gas species on vertical ozone distribution.

Development of a Photon Counting System for Differential Lidar Signal Detection

NASA Technical Reports Server (NTRS)

Elsayed-Ali, Hani

1997-01-01

Photon counting has been chosen as a means to extend the detection range of current airborne DIAL ozone measurements. Lidar backscattered return signals from the on and off-line lasers experience a significant exponential decay. To extract further data from the decaying ozone return signals, photon counting will be used to measure the low light levels, thus extending the detection range. In this application, photon counting will extend signal measurement where the analog return signal is too weak. The current analog measurement range is limited to approximately 25 kilometers from an aircraft flying at 12 kilometers. Photon counting will be able to exceed the current measurement range so as to follow the mid-latitude model of ozone density as a function of height. This report describes the development of a photon counting system. The initial development phase begins with detailed evaluation of individual photomultiplier tubes. The PMT qualities investigated are noise count rates, single electron response peaks, voltage versus gain values, saturation effects, and output signal linearity. These evaluations are followed by analysis of two distinctive tube base gating schemes. The next phase is to construct and operate a photon counting system in a laboratory environment. The laboratory counting simulations are used to determine optimum discriminator setpoints and to continue further evaluations of PMT properties. The final step in the photon counting system evaluation process is the compiling of photon counting measurements on the existing ozone DIAL laser system.

Development of the 1.6μm OPG/OPA system wavelength-controlled precisely for CO2 DIAL

NASA Astrophysics Data System (ADS)

Abo, M.; Shibata, Y.; Nagasawa, C.

2010-12-01

We developed an optical parametric oscillator (OPO) laser system for 1.6μm CO2 DIAL1). In order to improve the measurement accuracy of CO2 profiles, development of high power and wavelength stabilized laser system has been conducted. We report a new high-power 1.6μm laser transmitter based on a parametric master oscillator-power amplifier (MOPA) system pumped by a LD-pumped Q-switched Nd:YAG laser which has the injection seed laser locked to the iodine absorption line. The master oscillator is an optical parametric generator (OPG), based on an MgO-doped periodically poled LiTaO3 (PPMgLT) crystal. The OPOs require either active control of the cavity length or slight misalignment of the cavity. On the other hand, the OPGs do not require a cavity and instead rely on sufficient conversion efficiency to be obtained with a single pass through the crystal. The single-frequency oscillation of the OPG was achieved by injection seeding. The 1.6μm emission of the OPG is amplified by two-stage optical parametric amplifiers (OPAs). The each PPMgLT crystal was mounted on the copper holder, and the temperature control of the each holder was carried out within 0.01 K. The wavelength feedback system of the Nd:YAG seed laser is performed with the side locking of the iodine absorption spectrum (line No.1107) and the frequency stability is realized within 10 MHz rms. Stabilization of the 1.6μm DFB seed laser is estimated to within 4 MHz rms at the CO2 absorption line center and within 1.8 MHz rms at the CO2 absorption line slope using the wavelength control unit. We demonstrated single-longitudinal-mode emission with the OPG and two OPAs. The beam quality was TEM00 mode, the pulse energy was 12 mJ at 500 Hz repetition rate and the frequency stability was less than 10MHz rms. The unique performances of this optical parametric system make a relevant transmitter for CO2 DIAL. This work was financially supported by the System Development Program for Advanced Measurement and Analysis of the Japan Science and Technology Agency. Reference (1) D. Sakaisawa, C. Nagasawa, T. Nagai, M. Abo, Y. Shibata, H. Nagai, M. Nakazato, and T. Sakai, Development of a 1.6μm differential absorption lidar with a quasi-phase-matching optical parametric oscillator and photon-counting detector for the vertical CO2 profile, Applied Optics, Vol.48, No.4, pp.748-757, 2009.

Atmospheric remote sensing of water vapor, HCl and CH4 using a continuously tunable Co:MgF2 laser

NASA Technical Reports Server (NTRS)

Menyuk, Norman; Killinger, Dennis K.

1987-01-01

A differential-absorption lidar system has been developed which uses a continuously tunable (1.5-2.3 micron) cobalt-doped magnesium fluoride laser as the radiation source. Preliminary atmospheric measurements of water vapor, HCl, and CH4 have been made with this system, including both path-averaged and ranged-resolved DIAL measurements at ranges up to 6 and 3 km, respectively.

First measurements of a carbon dioxide plume from an industrial source using a ground based mobile differential absorption lidar.

PubMed

Robinson, R A; Gardiner, T D; Innocenti, F; Finlayson, A; Woods, P T; Few, J F M

2014-08-01

The emission of carbon dioxide (CO2) from industrial sources is one of the main anthropogenic contributors to the greenhouse effect. Direct remote sensing of CO2 emissions using optical methods offers the potential for the identification and quantification of CO2 emissions. We report the development and demonstration of a ground based mobile differential absorption lidar (DIAL) able to measure the mass emission rate of CO2 in the plume from a power station. To our knowledge DIAL has not previously been successfully applied to the measurement of emission plumes of CO2 from industrial sources. A significant challenge in observing industrial CO2 emission plumes is the ability to discriminate and observe localised concentrations of CO2 above the locally observed background level. The objectives of the study were to modify our existing mobile infrared DIAL system to enable CO2 measurements and to demonstrate the system at a power plant to assess the feasibility of the technique for the identification and quantification of CO2 emissions. The results of this preliminary study showed very good agreement with the expected emissions calculated by the site. The detection limit obtained from the measurements, however, requires further improvement to provide quantification of smaller emitters of CO2, for example for the detection of fugitive emissions. This study has shown that in principle, remote optical sensing technology will have the potential to provide useful direct data on CO2 mass emission rates.

Differential Absorption Lidar (DIAL) Measurements of Landfill Methane Emissions

NASA Astrophysics Data System (ADS)

Innocenti, Fabrizio; Robinson, Rod; Gardiner, Tom; Finlayson, Andrew; Connor, Andy

2017-04-01

DIFFERENTIAL ABSORPTION LIDAR (DIAL) MEASURMENTS OF LANDFILL METHANE EMISSIONS F. INNOCENTI *, R.A. ROBINSON *, T.D. GARDINER, A. FINLAYSON *, A. CONNOR* * National Physical Laboratory (NPL), Hampton Road, Teddington, Middlesex, TW11 0LW, United Kingdom Methane is one of the most important gaseous hydrocarbon species for both industrial and environmental reasons. Understanding and quantifying methane emissions to atmosphere is an important element of climate change research. Range-resolved infrared Differential Absorption Lidar (DIAL) measurements provide the means to map and quantify a wide range of different methane sources. DIAL is a powerful technique that can be used to track and quantify plumes emitted from area emission sources such as landfill sites, waste water treatment plants and petrochemical plants. By using lidar (light detection and ranging), the DIAL technique is able to make remote range-resolved single-ended measurements of the actual distribution of target gases in the atmosphere, with no disruption to normal site operational activities. DIAL provides 3D mapping of emission concentrations and quantification of emission rates for a wide range of target gases such as methane. The NPL DIAL laser source is operated alternately at two similar wavelengths. One of these, termed the "on-resonant wavelength", is chosen to be at a wavelength which is absorbed by the target species. The other, the "off-resonant wavelength", is chosen to be at a nearby wavelength which is not absorbed significantly by the target species. The two wavelengths are chosen to be close, so that the atmospheric scattering properties are the same for both wavelengths. They are also chosen so that any differential absorption due to other atmospheric species are minimised. Any measured difference in the returned signals is therefore due to absorption by the target gas. In the typical DIAL measurement configuration the mobile DIAL facility is positioned downwind of the area being investigated. The DIAL laser beam is then scanned in a vertical plane and the distribution of the target gas in the measurement plane is mapped. By combining this information with the wind conditions, the technique provides a direct measure of the emission rate of the target gas and its spatial distribution rather than the path-averaged concentration given by most other optical remote sensing methods. This means that localised, high concentration plumes can be discriminated from broad, low concentration plumes, and that emissions from different sources within an area can be spatially separated and independently quantified. As an example, the localised emission from an engine stack or flare can be separated from the diffuse emission from a capped area. Horizontal scans just above the surface can also be performed and they are generally used to identify emission hot-spots. Over the last decade the NPL DIAL system has carried out landfill emission surveys at over thirty sites in the UK, France and the USA measuring the total site and area-specific emissions from e.g. active areas, capped areas and engine stacks. This history of emissions measurements made with DIAL at landfill sites is testament to the maturity of the technique that can be deployed as reference tool by the waste industry. The DIAL data can be used by the site operators to validate emissions estimates and by the regulators to revise and update the emission inventories.

Mid-IR DIAL for high-resolution mapping of explosive precursors

NASA Astrophysics Data System (ADS)

Mitev, V.; Babichenko, S.; Bennes, J.; Borelli, R.; Dolfi-Bouteyre, A.; Fiorani, L.; Hespel, L.; Huet, T.; Palucci, A.; Pistilli, M.; Puiu, A.; Rebane, O.; Sobolev, I.

2013-10-01

A DIAL instrument on a moving platform is seen as a valuable remote sensing component in a sensor network for area monitoring, targeting sites involved in unauthorised explosive manufacturing. Such instrument will perform the area mapping of the vapour concentration of key substances, known to be used as precursors in explosive fabrication, such as acetone and nitromethane. The IR spectra of acetone and nitromethane vapours have been defined from available spectroscopy databases and from laboratory measurements as showing optimal spectral band for the DIAL operation in the spectral range of 3.0 μm - 3.5 μm. The DIAL operation has been numerically simulated, with inputs based on the HITRAN database, the U.S. Standard Atmosphere and aerosol simulation software package OPAC. A combination of OPO and OPA has been chosen as a transmitter, where the idler wavelength is used for probing, with wavelength tuning in sequence. A scanner mounted on top of the coaxially aligned laser and receiver, is capable of covering almost 360 degrees horizontally and +/-30 degrees vertically. The detection is performed by a photovoltaic photodiode with 4-stage cooling, with a signal digitalisation having 14 bit amplitude resolution and 125 Ms/s sampling rate. Here we present the development and the first test of the DIAL instrument.

Mobile phone radiation induces mode-dependent DNA damage in a mouse spermatocyte-derived cell line: a protective role of melatonin.

PubMed

Liu, Chuan; Gao, Peng; Xu, Shang-Cheng; Wang, Yuan; Chen, Chun-Hai; He, Min-Di; Yu, Zheng-Ping; Zhang, Lei; Zhou, Zhou

2013-11-01

To evaluate whether exposure to mobile phone radiation (MPR) can induce DNA damage in male germ cells. A mouse spermatocyte-derived GC-2 cell line was exposed to a commercial mobile phone handset once every 20 min in standby, listen, dialed or dialing modes for 24 h. DNA damage was determined using an alkaline comet assay. The levels of DNA damage were significantly increased following exposure to MPR in the listen, dialed and dialing modes. Moreover, there were significantly higher increases in the dialed and dialing modes than in the listen mode. Interestingly, these results were consistent with the radiation intensities of these modes. However, the DNA damage effects of MPR in the dialing mode were efficiently attenuated by melatonin pretreatment. These results regarding mode-dependent DNA damage have important implications for the safety of inappropriate mobile phone use by males of reproductive age and also suggest a simple preventive measure: Keeping mobile phones as far away from our body as possible, not only during conversations but during 'dialed' and 'dialing' operation modes. Since the 'dialed' mode is actually part of the standby mode, mobile phones should be kept at a safe distance from our body even during standby operation. Furthermore, the protective role of melatonin suggests that it may be a promising pharmacological candidate for preventing mobile phone use-related reproductive impairments.

Chemistry and dynamics of the lower troposphere over North America and the North Atlantic Ocean in fall 1997 observed using an airborne UV DIAL system

NASA Technical Reports Server (NTRS)

Grant, William B.; Butler, Carolyn F.; Fenn, Marta A.; Kooi, Susan A.; Browell, Edward V.; Fuelberg, Henry

1998-01-01

The NASA Langley Research Center's airborne UV Differential Absorption Lidar (DIAL) system participated in the Subsonic Assessment, Ozone and Nitrogen Oxide Experiment (SONEX) mission from October 13 to November 12, 1997. The purpose of the mission was to study the upper troposphere/lower stratosphere in and near the North Atlantic flight corridor to better understand this region of the atmosphere and how civilian air travel in the corridor might be affecting the atmospheric chemistry. Bases of operations included NASA Ames, California (37.4 deg N, 122.1 deg W); Bangor, Maine (44.8 deg N, 68.8 deg W); Shannon, Ireland (52.7 deg N, 8.9 deg W); and Lajes, Terceira Island, Azores (38.8 deg N, 27.1 deg W). Since the UV DIAL system observes in the nadir as well as the zenith, aerosol and ozone data were obtained from near the Earth's surface to the lower stratosphere. A number of interesting features were noted relating to both chemistry and dynamics of the troposphere, which are reported here.

Development and Deployment of a Compact Eye-Safe Scanning Differential absorption Lidar (DIAL) for Spatial Mapping of Carbon Dioxide for Monitoring/Verification/Accounting at Geologic Sequestration Sites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Repasky, Kevin

2014-03-31

A scanning differential absorption lidar (DIAL) instrument for monitoring carbon dioxide has been developed. The laser transmitter uses two tunable discrete mode laser diodes (DMLD) operating in the continuous wave (cw) mode with one locked to the online absorption wavelength and the other operating at the offline wavelength. Two in-line fiber optic switches are used to switch between online and offline operation. After the fiber optic switch, an acousto- optic modulator (AOM) is used to generate a pulse train used to injection seed an erbium doped fiber amplifier (EDFA) to produce eye-safe laser pulses with maximum pulse energies of 66more » {micro}J, a pulse repetition frequency of 15 kHz, and an operating wavelength of 1.571 {micro}m. The DIAL receiver uses a 28 cm diameter Schmidt-Cassegrain telescope to collect that backscattered light, which is then monitored using a photo-multiplier tube (PMT) module operating in the photon counting mode. The DIAL instrument has been operated from a laboratory environment on the campus of Montana State University, at the Zero Emission Research Technology (ZERT) field site located in the agricultural research area on the western end of the Montana State University campus, and at the Big Sky Carbon Sequestration Partnership site located in north-central Montana. DIAL data has been collected and profiles have been validated using a co-located Licor LI-820 Gas Analyzer point sensor.« less

Digital Radiography

NASA Technical Reports Server (NTRS)

1986-01-01

System One, a digital radiography system, incorporates a reusable image medium (RIM) which retains an image. No film is needed; the RIM is read with a laser scanner, and the information is used to produce a digital image on an image processor. The image is stored on an optical disc. System allows the radiologist to "dial away" unwanted images to compare views on three screens. It is compatible with existing equipment and cost efficient. It was commercialized by a Stanford researcher from energy selective technology developed under a NASA grant.

Comparison of 2 micron Ho and 10 micron CO2 lidar for atmospheric backscatter and Doppler windshear detection

NASA Technical Reports Server (NTRS)

Killinger, Dennis

1991-01-01

The development of eye-safe, solid-state Lidar systems is discussed, with an emphasis on Coherent Doppler Lidar for Atmospheric Wind Measurements. The following subject areas are covered: tunable Ho DIAL (Differential Absorption Lidar)/lidar atmospheric measurements; atmospheric turbulence measurements and detector arrays; diurnal measurements of C(sub n)(sup 2) for KSC lidar measurements; and development of single-frequency Ho laser/lidar.

Diode-laser-based water vapor differential absorption lidar (DIAL) profiler evaluation

NASA Astrophysics Data System (ADS)

Spuler, S.; Weckwerth, T.; Repasky, K. S.; Nehrir, A. R.; Carbone, R.

2012-12-01

We are in the process of evaluating the performance of an eye-safe, low-cost, diode-laser-based, water vapor differential absorption lidar (DIAL) profiler. This class of instrument may be capable of providing continuous water vapor and aerosol backscatter profiles at high vertical resolution in the atmospheric boundary layer (ABL) for periods of months to years. The technology potentially fills a national long term observing facility gap and could greatly benefit micro- and meso-meteorology, water cycle, carbon cycle and, more generally, biosphere-hydrosphere-atmosphere interaction research at both weather and climate variability time scales. For the evaluation, the Montana State University 3rd generation water vapor DIAL was modified to enable unattended operation for a period of several weeks. The performance of this V3.5 version DIAL was tested at MSU and NCAR in June and July of 2012. Further tests are currently in progress with Howard University at Beltsville, Maryland; and with the National Weather Service and Oklahoma University at Dallas/Fort Worth, Texas. The presentation will include a comparison of DIAL profiles against meteorological "truth" at the aforementioned locations including: radiosondes, Raman lidars, microwave and IR radiometers, AERONET and SUOMINET systems. Instrument reliability, uncertainty, systematic biases, detection height statistics, and environmental complications will be evaluated. Performance will be judged in the context of diverse scientific applications that range from operational weather prediction and seasonal climate variability, to more demanding climate system process studies at the land-canopy-ABL interface. Estimating the extent to which such research and operational applications can be satisfied with a low cost autonomous network of similar instruments is our principal objective.

47 CFR 51.215 - Dialing parity: Cost recovery.

Code of Federal Regulations, 2010 CFR

2010-10-01

... (CONTINUED) INTERCONNECTION Obligations of All Local Exchange Carriers § 51.215 Dialing parity: Cost recovery. (a) A LEC may recover the incremental costs necessary for the implementation of toll dialing parity... 47 Telecommunication 3 2010-10-01 2010-10-01 false Dialing parity: Cost recovery. 51.215 Section...

Call progress time measurement in IP telephony

NASA Astrophysics Data System (ADS)

Khasnabish, Bhumip

1999-11-01

Usually a voice call is established through multiple stages in IP telephony. In the first stage, a phone number is dialed to reach a near-end or call-originating IP-telephony gateway. The next stages involve user identification through delivering an m-digit user-id to the authentication and/or billing server, and then user authentication by using an n- digit PIN. After that, the caller is allowed (last stage dial tone is provided) to dial a destination phone number provided that authentication is successful. In this paper, we present a very flexible method for measuring call progress time in IP telephony. The proposed technique can be used to measure the system response time at every stage. It is flexible, so that it can be easily modified to include new `tone' or a set of tones, or `voice begin' can be used in every stage to detect the system's response. The proposed method has been implemented using scripts written in Hammer visual basic language for testing with a few commercially available IP telephony gateways.

An Ozone Differential Absorption Lidar (DIAL) Receiver System for Use on Unpiloted Atmospheric Vehicles

NASA Technical Reports Server (NTRS)

DeYoung, Russell J.; Goldschmidt, Soenke

1999-01-01

Measurements of global atmosphere ozone concentrations call for flexible lidar systems that can be operated from an unpiloted atmospheric vehicle (UAV) to reduce the cost of measurement missions. A lidar receiver system consisting of a fiber-optic-coupled telescope has been designed and tested for this purpose. The system weight is 13 kg and its volume of 0.06 m 3 would fit into the payload compartment of a Perseus B UAV. The optical efficiency of the telescope is 37 percent at 288 nm and 64 percent at 300 nm. Atmospheric measurements with a DIAL laser system have been performed, and the measured ozone density has matched the data from ozonesondes to an altitude of 7 km.

Implementation and flight tests for the Digital Integrated Automatic Landing System (DIALS). Part 2: Complete set of flight data

NASA Technical Reports Server (NTRS)

Hueschen, R. M.

1986-01-01

Five flight tests of the Digital Automated Landing System (DIALS) were conducted on the Advanced Transport Operating System (ATOPS) Transportation Research Vehicle (TSRV)--a modified Boeing 737 Aircraft for advanced controls and displays research. These flight tests were conducted at NASA's Wallops Flight Center using the Microwave Landing System (MLS) installation on Runway 22. This report is primarily a collection of data plots of all performance variables recorded for the entire five flight tests. A description and source of the performance variables is included. Performance variables include inertial data, air data, automatic control commands, control servo positions, sensor data, DIALS guidance and control parameters, and Kalman filter data. This data illustrates low overshoot captures of the localizer for intercept angles of 20 deg, 30 deg, 40 deg, and 50 deg intercept angles, and low overshoot captures of the glideslope slope for 3 deg, 4.5 deg, and 5 deg glideslopes. Flare maneuvers were successfully performed from the various glideslope angles and good decrab maneuvers were performed in crosswinds of 6 knots. In 18 to 20 knot crosswind conditions rudder limiting occurred which caused lateral drifting although heading alignment was achieved.

Mobile lidar system for monitoring of gaseous pollutants in atmosphere over industrial and urban area

NASA Astrophysics Data System (ADS)

Moskalenko, Irina V.; Shecheglov, Djolinard A.; Rogachev, Aleksei P.; Avdonin, Aleksandr A.; Molodtsov, Nikolai A.

1999-01-01

The lidar remote sensing techniques are powerful for monitoring of gaseous toxic species in atmosphere over wide areas. The paper presented describes design, development and field testing of Mobile Lidar System (MLS) based on utilization of Differential Absorption Lidar (DIAL) technique. The activity is performed by Russian Research Center 'Kurchatov Institute' and Research Institute of Pulse Technique within the project 'Mobile Remote SEnsing System Based on Tunable Laser Transmitter for Environmental Monitoring' under funding of International Scientific and Technology Center Moscow. A brief description of MLS is presented including narrowband transmitter, receiver, system steering, data acquisition subsystem and software. MLS is housed in a mobile truck and is able to provide 3D mapping of gaseous species. Sulfur dioxide and elemental mercury were chosen as basic atmospheric pollutants for field test of MLS. The problem of anthropogenic ozone detection attracts attention due to increase traffic in Moscow. The experimental sites for field testing are located in Moscow Region. Examples of field DIAL measurements will be presented. Application of remote sensing to toxic species near-real time measurements is now under consideration. The objective is comparison of pollution level in working zone with maximum permissible concentration of hazardous pollutant.

Barium Nitrate Raman Laser Development for Remote Sensing of Ozone

NASA Technical Reports Server (NTRS)

McCray, Christopher L.; Chyba, Thomas H.

1997-01-01

In order to understand the impact of anthropogenic emissions upon the earth's environment, scientists require remote sensing techniques which are capable of providing range-resolved measurements of clouds, aerosols, and the concentrations of several chemical constituents of the atmosphere. The differential absorption lidar (DIAL) technique is a very promising method to measure concentration profiles of chemical species such as ozone and water vapor as well as detect the presence of aerosols and clouds. If a suitable DIAL system could be deployed in space, it would provide a global data set of tremendous value. Such systems, however, need to be compact, reliable, and very efficient. In order to measure atmospheric gases with the DIAL technique, the laser transmitter must generate suitable on-line and off-line wavelength pulse pairs. The on-line pulse is resonant with an absorption feature of the species of interest. The off-line pulse is tuned so that it encounters significantly less absorption. The relative backscattered power for the two pulses enables the range-resolved concentration to be computed. Preliminary experiments at NASA LaRC suggested that the solid state Raman shifting material, Ba(NO3)2, could be utilized to produce these pulse pairs. A Raman oscillator pumped at 532 nm by a frequency-doubled Nd:YAG laser can create first Stokes laser output at 563 nm and second Stokes output at 599 nm. With frequency doublers, UV output at 281 nm and 299 nm can be subsequently obtained. This all-solid state system has the potential to be very efficient, compact, and reliable. Raman shifting in Ba(NO3)2, has previously been performed in both the visible and the infrared. The first Raman oscillator in the visible region was investigated in 1986 with the configurations of plane-plane and unstable telescopic resonators. However, most of the recent research has focused on the development of infrared sources for eye-safe lidar applications.

47 CFR 51.207 - Local dialing parity.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 3 2013-10-01 2013-10-01 false Local dialing parity. 51.207 Section 51.207... Obligations of All Local Exchange Carriers § 51.207 Local dialing parity. A LEC shall permit telephone exchange service customers within a local calling area to dial the same number of digits to make a local...

47 CFR 51.207 - Local dialing parity.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 3 2010-10-01 2010-10-01 false Local dialing parity. 51.207 Section 51.207... Obligations of All Local Exchange Carriers § 51.207 Local dialing parity. A LEC shall permit telephone exchange service customers within a local calling area to dial the same number of digits to make a local...

47 CFR 51.207 - Local dialing parity.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 3 2011-10-01 2011-10-01 false Local dialing parity. 51.207 Section 51.207... Obligations of All Local Exchange Carriers § 51.207 Local dialing parity. A LEC shall permit telephone exchange service customers within a local calling area to dial the same number of digits to make a local...

47 CFR 51.207 - Local dialing parity.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 3 2014-10-01 2014-10-01 false Local dialing parity. 51.207 Section 51.207... Obligations of All Local Exchange Carriers § 51.207 Local dialing parity. A LEC shall permit telephone exchange service customers within a local calling area to dial the same number of digits to make a local...

47 CFR 51.207 - Local dialing parity.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 3 2012-10-01 2012-10-01 false Local dialing parity. 51.207 Section 51.207... Obligations of All Local Exchange Carriers § 51.207 Local dialing parity. A LEC shall permit telephone exchange service customers within a local calling area to dial the same number of digits to make a local...

A Two Micron Coherent Differential Absorption Lidar Development

NASA Technical Reports Server (NTRS)

Yu, Jirong; Petros, Mulugeta; Chen, Songsheng; Bai, Yingxin; Petzar, Paul J.; Trieu, Bo C.; Koch, Grady J.; Beyon, Jeffrey Y.; VanValkenburg, Randal L.; Kavaya, Michael J.;

NORDA’s Pattern Analysis Laboratory: Current Contributions to Naval Mapping, Charting, and Geodesy

DTIC Science & Technology

1989-04-01

magnetic observatories (McLeod, 1988). Using system integrates a suite of sensors and control devices the PAL’s VAX 11/780, spherical harmonic models to...DJAO:[FPS]*.OLB 5. Miscellaneous Utilities CALENDAR (NORDA events) 780 $ CALENDAR (menu-driven) DIALER modem controller 780 $ R AUTO DIAL:DIALER DTC...Utilities CALENDAR (NORDA events) 780 CALENDAR (menu-driven) DIALER modem controller 780 $ R AUTO DIAL:DIALER DTC Desk Top Calendar 780 $ DTC (menu-driven

Ground-based eye-safe networkable micro-pulse differential absorption and high spectral resolution lidar for water vapor and aerosol profiling in the lower troposphere

NASA Astrophysics Data System (ADS)

Repasky, K. S.; Spuler, S.; Hayman, M. M.; Bunn, C. E.

2017-12-01

Atmospheric water vapor is a greenhouse gas that is known to be a significant driver of weather and climate. Several National Research Council (NRC) reports have highlighted the need for improved water vapor measurements that can capture its spatial and temporal variability as a means to improve weather predictions. Researchers at Montana State University (MSU) and the National Center for Atmospheric Research (NCAR) have developed an eye-safe diode laser based micro-pulse differential absorption lidar (MP-DIAL) for water vapor profiling in the lower troposphere. The MP-DIAL is capable of long term unattended operation and is capable of monitoring water vapor in the lower troposphere in most weather conditions. Two MP-DIAL instruments are currently operational and have been deployed at the Front Range Air Pollution and Photochemistry Experiment (FRAPPE), the Plains elevated Convection at Night (PECAN) experiment, the Perdigão experiment, and the Land Atmosphere Feedback Experiment (LAFE). For each of these field experiments, the MP-DIAL was run unattended and provided near-continuous water vapor profiles, including periods of bright daytime clouds, from 300 m above the ground level to 4 km (or the cloud base) with 150 m vertical resolution and 5 minute temporal resolution. Three additional MP-DIAL instruments are currently under construction and will result in a network of five eye-safe MP-DIAL instruments for ground based weather and climate research experiments. Taking advantage of the broad spectral coverage and modularity or the diode based architecture, a high spectral resolution lidar (HSRL) measurement capabilities was added to the second MP-DIAL instrument. The HSRL capabilities will be operational during the deployment at the LAFE field experiment. The instrument architecture will be presented along with examples of data collected during recent field experiments.

Laser long-range remote-sensing program experimental results

NASA Astrophysics Data System (ADS)

Highland, Ronald G.; Shilko, Michael L.; Fox, Marsha J.; Gonglewski, John D.; Czyzak, Stanley R.; Dowling, James A.; Kelly, Brian; Pierrottet, Diego F.; Ruffatto, Donald; Loando, Sharon; Matsuura, Chris; Senft, Daniel C.; Finkner, Lyle; Rae, Joe; Gallegos, Joe

1995-12-01

A laser long range remote sensing (LRS) program is being conducted by the United States Air Force Phillips Laboratory (AF/PL). As part of this program, AF/PL is testing the feasibility of developing a long path CO(subscript 2) laser-based DIAL system for remote sensing. In support of this program, the AF/PL has recently completed an experimental series using a 21 km slant- range path (3.05 km ASL transceiver height to 0.067 km ASL target height) at its Phillips Laboratory Air Force Maui Optical Station (AMOS) facility located on Maui, Hawaii. The dial system uses a 3-joule, (superscript 13)C isotope laser coupled into a 0.6 m diameter telescope. The atmospheric optical characterization incorporates information from an infrared scintillometer co-aligned to the laser path, atmospheric profiles from weather balloons launched from the target site, and meteorological data from ground stations at AMOS and the target site. In this paper, we report a description of the experiment configuration, a summary of the results, a summary of the atmospheric conditions and their implications to the LRS program. The capability of such a system for long-range, low-angle, slant-path remote sensing is discussed. System performance issues relating to both coherent and incoherent detection methods, atmospheric limitations, as well as, the development of advanced models to predict performance of long range scenarios are presented.

Development of a Micro Pulsed Lidar and a Singly-Resonant Optical Parametric Oscillator for CO2 Dial for Use in Atmospheric Studies

NASA Astrophysics Data System (ADS)

Chantjaroen, Chat

According to the Fifth Assessment Report (AR5) from the Intergovernmental Panel on Climate Change (IPCC), aerosols and CO2 are the largest contributors to anthropogenic radiative forcing--net negative for aerosols and positive for CO2. This relates to the amount of impact that aerosols and CO2 can have on our atmosphere and climate system. CO2 is the predominant greenhouse gas in the atmosphere and causes great impacts on our climate system. Recent studies show that a less well known atmospheric component--aerosols, which are solid particles or liquid droplets suspended in air, can cause great impact on our climate system too. They can affect our climate directly by absorbing and scattering sunlight to warm or cool our climate. They can also affect our climate indirectly by affecting cloud microphysical properties. Typically sulfate aerosols or sea salts act as condensation nuclei for clouds to form. Clouds are estimated to shade about 60% of the earth at any given time. They are preventing much of the sunlight from reaching the earth's surface and are helping with the flow of the global water cycle. These are what permit lifeforms on earth. In the IPCC report, both aerosols and CO2 also have the largest uncertainties and aerosols remains at a low level of scientific understanding. These indicate the need of more accurate measurements and that new technologies and instruments needs to be developed. This dissertation focuses on the development of two instruments--a scannable Micro-Pulsed Lidar (MPL) for atmospheric aerosol measurements and an Optical Parametric Oscillator (OPO) for use as a transmitter in a Differential Absorption Lidar (DIAL) for atmospheric CO2 measurements. The MPL demonstrates successful measurements of aerosols. It provides the total aerosol optical depth (AOD) and aerosol lidar ratio (Sa) that agree well with an instrument used by the Aerosol Robotic Network (AERONET). It also successfully provides range-resolved information about aerosols that AERONET instrument is incapable of. The range-resolved information is important in the study of the sources and sinks of aerosols. The OPO results show good promise for its use as a DIAL transmitter.

A compact high repetition rate CO2 coherent Doppler lidar

NASA Technical Reports Server (NTRS)

Alejandro, S.; Frelin, R.; Dix, B.; Mcnicholl, P.

1992-01-01

As part of its program to develop coherent heterodyne detection lidar technology for space, airborne, and ground based applications, the Optical Environment Division of the USAF's Phillips Laboratory developed a compact coherent CO2 TEA lidar system. Although originally conceived as a high altitude balloon borne system, the lidar is presently integrated into a trailer for ground based field measurements of aerosols and wind fields. In this role, it will also serve as a testbed for signal acquisition and processing development for planned future airborne and space based solid state lidar systems. The system has also found significance in new areas of interest to the Air Force such as cloud studies and coherent Differential Absorption Lidar (DIAL) systems.

New capability for ozone dial profiling measurements in the troposphere and lower stratosphere from aircraft

NASA Astrophysics Data System (ADS)

Hair, Johnathan; Hostetler, Chris; Cook, Anthony; Harper, David; Notari, Anthony; Fenn, Marta; Newchurch, Mike; Wang, Lihua; Kuang, Shi; Knepp, Travis; Burton, Sharon; Ferrare, Richard; Butler, Carolyn; Collins, Jim; Nehrir, Amin

2018-04-01

Recently, we successfully demonstrated a new compact and robust ozone DIAL lidar for smaller aircraft such as the NASA B200 and the ER-2 high-altitude aircraft. This is the first NASA airborne lidar to incorporate advanced solid-state lasers to produce the required power at the required ultraviolet wavelengths, and is compact and robust enough to operate nearly autonomously on the high-altitude ER-2 aircraft. This technology development resulted in the first new NASA airborne ozone DIAL instrument in more than 15 years. The combined ozone, aerosol, and clouds measurements provide valuable information on the chemistry, radiation, and dynamics of the atmosphere. In particular, from the ER-2 it offers a unique capability to study the upper troposphere and lower stratosphere.

USAFETAC Online Climatology: Dial-In Service Users Manual

DTIC Science & Technology

1994-02-01

89.57 U 155 724455 KIRKSVILLE REGIONAL MO 40.06 N 92.33 w 156 746710 FORT CAMPBELL (AAF) KY 36.40 N 87.30 W 158 723407 JONESBORO MUNICIPAL AR 35.50 N...In services, available to any agency of the U.S. Government, are provided upon validation of a support assistance request submitted in accordance with...users need help with Dial-In, they can get it by using the two- way message system. USAFETAC services are not limited to the software currently

Development of the Global Ozone Lidar Demonstrator (GOLD) Instrument for Deployment on the NASA Global Hawk

NASA Technical Reports Server (NTRS)

Hair, Jonathan W.; Browell, Edward V.; McGee, Thomas; Butler, Carolyn; Fenn, Marta; Os,ao (. Sued); Notari, Anthony; Collins, James; Cleckner, Craig; Hostetler, Chris

2010-01-01

A compact ozone (O3) and aerosol lidar system is being developed for conducting global atmospheric investigations from the NASA Global Hawk Uninhabited Aerial Vehicle (UAV) and for enabling the development and test of a space-based O3 and aerosol lidar. GOLD incorporates advanced technologies and designs to produce a compact, autonomously operating O3 and aerosol Differential Absorption Lidar (DIAL) system for a UAV platform. The GOLD system leverages advanced Nd:YAG and optical parametric oscillator laser technologies and receiver optics, detectors, and electronics. Significant progress has been made toward the development of the GOLD system, and this paper describes the objectives of this program, basic design of the GOLD system, and results from initial ground-based atmospheric tests.

Remote sensing of air pollution over large European cities by lidar

NASA Astrophysics Data System (ADS)

Koelsch, Hans J.; Kolenda, Juergen; Rairoux, Patrick; Stein, Bernhard; Weidauer, Dirk; Wolf, Jean-Pierre; Woeste, Ludger H.; Fritzsche, Klaus

1992-12-01

Progresses in remote sensing of the atmosphere using the light detection and ranging (lidar) technique closely follows progresses in laser technology. We developed a mobile differential absorption lidar (DIAL) system, based on high repetition rate excimer-pumped dye lasers, for performing 2-D and 3-D mappings of concentration of NO, NO2, SO2, and O3. The high sensitivity of the system has been used for numerous environmental studies and measurement campaigns, providing for the first time a direct correlation between emission and immission. Attractive results have been obtained under urban conditions, because of the presence of strong concentration gradients, and fast fluctuations due to traffic. A comparative study between Lyon, France; Stuttgart, Germany; Geneva, Switzerland; and Berlin, Germany; is presented. In particular, the Berlin campaign demonstrates the possibility of detecting unknown emitters and monitoring exportation-importation processes of atmospheric pollution. A new stationary DIAL system has recently been constructed and implemented on the top of a building in the center of the city of Leipzig, Germany. It will routinely perform concentration mappings of nitrogen oxides, sulfur dioxide, and ozone, giving access to long term evolution of pollution distributions.

WALES: water vapour lidar experiment in space

NASA Astrophysics Data System (ADS)

Guerin, F.; Pain, Th.; Palmade, J.-L.; Pailharey, E.; Giraud, D.; Jubineau, F.

2017-11-01

The WAter vapour Lidar Experiment in Space (WALES) mission aims at providing water vapour profiles with high accuracy and vertical resolution through the troposphere and the lower stratosphere on a global scale using an instrument based on Differential Absorption Lidar (DIAL) observation technique, and mounted on an Earth orbiting satellite. This active DIAL technique will also provide data on the cloud coverage by means of the signal reflection on the cloud layers. In DIAL operation, backscatter lidar signals at two wavelengths - at least - are detected. One wavelength (λ ON) is highly absorbed by the species of interest, while the other (λ OFF) is backscattered with minimal absorption. This difference in absorption at the two transmitted wavelengths leads to the determination of the concentration of the species of interest. The DIAL is therefore a dual-wavelength lidar in which the signals detected at the two wavelengths are processed to extract the absolute density of water vapour. The Phase A study performed by ALCATEL Space and their partners under contract of the European Space Agency has led to a credible and innovative concept of instrument, based on a mission performance modelling. The challenge is to foster the scientific return while minimising the development risks and costs of instrument development, in particular the laser transmitter. The paper describes the payload design and the implementation on a low Earth orbiting (LEO) satellite.

WALES: WAter vapour Lidar Experiment in Space

NASA Astrophysics Data System (ADS)

Guerin, F.; Pain, Th.; Palmade, J. L.; Pailharey, E.; Giraud, D.; Jubineau, F.

2004-06-01

The WAter vapour Lidar Experiment in Space (WALES) mission aims at providing water vapour profiles with high accuracy and vertical resolution through the troposphere and the lower stratosphere on a global scale using an instrument based on Differential Absorption Lidar (DIAL) observation technique, and mounted on an Earth orbiting satellite. This active DIAL technique will also provide data on the cloud coverage by means of the signal reflection on the cloud layers. In DIAL operation, backscatter lidar signals at two wavelengths - at least - are detected. One wavelength (λ ON) is highly absorbed by the species of interest, while the other (λ OFF) is backscattered with minimal absorption. This difference in absorption at the two transmitted wavelengths leads to the determination of the concentration of the species of interest. The DIAL is therefore a dual-wavelength lidar in which the signals detected at the two wavelengths are processed to extract the absolute density of water vapour. The Phase A study performed by ALCATEL Space and their partners under contract of the European Space Agency has led to a credible and innovative concept of instrument, based on a mission performance modelling. The challenge is to foster the scientific return while minimising the development risks and costs of instrument development, in particular the laser transmitter. The paper describes the payload design and the implementation on a low Earth orbiting (LEO) satellite.

UMEL: a new regression tool to identify measurement peaks in LIDAR/DIAL systems for environmental physics applications.

PubMed

Gelfusa, M; Gaudio, P; Malizia, A; Murari, A; Vega, J; Richetta, M; Gonzalez, S

2014-06-01

Recently, surveying large areas in an automatic way, for early detection of both harmful chemical agents and forest fires, has become a strategic objective of defence and public health organisations. The Lidar and Dial techniques are widely recognized as a cost-effective alternative to monitor large portions of the atmosphere. To maximize the effectiveness of the measurements and to guarantee reliable monitoring of large areas, new data analysis techniques are required. In this paper, an original tool, the Universal Multi Event Locator, is applied to the problem of automatically identifying the time location of peaks in Lidar and Dial measurements for environmental physics applications. This analysis technique improves various aspects of the measurements, ranging from the resilience to drift in the laser sources to the increase of the system sensitivity. The method is also fully general, purely software, and can therefore be applied to a large variety of problems without any additional cost. The potential of the proposed technique is exemplified with the help of data of various instruments acquired during several experimental campaigns in the field.

M/A-COM Linkabit Eastern Operations

DTIC Science & Technology

1983-03-31

Lincoln Laboratories speech codec for use in multimedia system development. Communication equipment included 1200-bps dial-up modems and a set of...connected to the DCN for use in[7, Page 4 general word-processing and network-testing applications.Additional modems and video terminals have also been...line 0) can be connected to a second terminal, a printer, or a modem . The standard configuration assumes this line is connected to a terminal or

Boundary Layer Observations of Water Vapor and Aerosol Profiles with an Eye-Safe Micro-Pulse Differential Absorption Lidar (DIAL)

NASA Astrophysics Data System (ADS)

Nehrir, A. R.; Repasky, K. S.; Carlsten, J.; Ismail, S.

2011-12-01

Measurements of real-time high spatial and temporal resolution profiles of combined water vapor and aerosols in the boundary layer have been a long standing observational challenge to the meteorological, weather forecasting, and climate science communities. To overcome the high reoccurring costs associated with radiosondes as well as the lack of sufficient water vapor measurements over the continental united states, a compact and low cost eye-safe all semiconductor-based micro-pulse differential absorption lidar (DIAL) has been developed for water vapor and aerosol profiling in the lower troposphere. The laser transmitter utilizes two continuous wave external cavity diode lasers operating in the 830 nm absorption band as the online and offline seed laser sources. An optical switch is used to sequentially injection seed a tapered semiconductor optical amplifier (TSOA) with the two seed laser sources in a master oscillator power amplifier (MOPA) configuration. The TSOA is actively current pulsed to produce up to 7 μJ of output energy over a 1 μs pulse duration (150 m vertical resolution) at a 10 kHz pulse repetition frequency. The measured laser transmitter spectral linewidth is less than 500 kHz while the long term frequency stability of the stabilized on-line wavelength is ± 55 MHz. The laser transmitter spectral purity was measured to be greater than 0.9996, allowing for simultaneous measurements of water vapor in the lower and upper troposphere. The DIAL receiver utilizes a commercially available full sky-scanning capable 35 cm Schmidt-Cassegrain telescope to collect the scattered light from the laser transmitter. Light collected by the telescope is spectrally filtered to suppress background noise and is coupled into a fiber optic cable which acts as the system field stop and limits the full angle field of view to 140 μrad. The light is sampled by a fiber coupled APD operated in a Geiger mode. The DIAL instrument is operated autonomously where water vapor and aerosol profiles are displayed in real-time. The transmitter is capable of operating at any spectral position along the selected water vapor absorption line allowing for year round operation at various geographical locations using a single line. Water vapor and aerosol profiles have been recorded up to 6 km and 15 km with 10 m and 1 m temporal averaging, respectively, allowing for mesoscale monitoring of boundary layer dynamics during both daytime and nighttime operation. A brief description of the current status of the water vapor DIAL instrument will be presented. Nighttime and daytime water vapor and aerosol profiles/inversions from the DIAL instrument will also be presented and favorable comparisons against collocated radiosonde, in situ, and column averaged data from SUOMINET and AERONET will also be discussed. A future outlook towards instrument enhancements that will allow the diode-laser-based DIAL technique/technology to become a viable candidate for deployment in multi-point sensor networks will also be discussed.

Feasibility study of microwave modulation DIAL system for global CO II monitoring

NASA Astrophysics Data System (ADS)

Hirano, Yoshihito; Kameyama, Shumpei; Ueno, Shinichi; Sugimoto, Nobuo; Kimura, Toshiyoshi

2006-12-01

A new concept of DIAL (DIfferential Absorption Lidar) system for global CO II monitoring using microwave modulation is introduced. This system uses quasi-CW lights which are intensity modulated in microwave region and receives a backscattered light from the ground. In this system, ON/OFF wavelength laser lights are modulated with microwave frequencies, and received lights of two wavelengths are able to be discriminated by modulation frequencies in electrical signal domain. Higher sensitivity optical detection can be realized compared with the conventional microwave modulation lidar by using direct down conversion of modulation frequency. The system also has the function of ranging by using pseudo-random coding in modulation. Fiber-based optical circuit using wavelength region of 1.6 micron is a candidate for the system configuration. After the explanation of this configuration, feasibility study of this system on the application to global CO II monitoring is introduced.

Combined 2-micron Dial and Doppler Lidar: Application to the Atmosphere of Earth or Mars

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Koch, Grady J.; Ismail, Syed; Kavaya, Michael; Yu, Jirong; Wood, Sidney A.; Emmitt, G. David

2006-01-01

A concept is explored for combining the Doppler and DIAL techniques into a single, multifunctional instrument. Wind, CO2 concentration, and aerosol density can all be measured. Technology to build this instrument is described, including the demonstration of a prototype lidar. Applications are described for use in the Earth science. The atmosphere of Mars can also be studied, and results from a recently-developed simulation model of performance in the Martian atmosphere are presented.

Airborne differential absorption lidar system for measurements of atmospheric water vapor and aerosols

NASA Technical Reports Server (NTRS)

Carter, Arlen F.; Allen, Robert J.; Mayo, M. Neale; Butler, Carolyn F.; Grossman, Benoist E.; Ismail, Syed; Grant, William B.; Browell, Edward V.; Higdon, Noah S.; Mayor, Shane D.;

Automated Blood Pressure Measurement

NASA Technical Reports Server (NTRS)

1978-01-01

The Vital-2 unit pictured is a semi-automatic device that permits highly accurate blood pressure measurement, even by untrained personnel. Developed by Meditron Instrument Corporation, Milford, New Hampshire, it is based in part on NASA technology found in a similar system designed for automatic monitoring of astronauts' blood pressure. Vital-2 is an advancement over the familiar arm cuff, dial and bulb apparatus customarily used for blood pressure checks. In that method, the physician squeezes the bulb to inflate the arm cuff, which restricts the flow of blood through the arteries. As he eases the pressure on the arm, he listens, through a stethoscope, to the sounds of resumed blood flow as the arteries expand and contract. Taking dial readings related to sound changes, he gets the systolic (contracting) and diastolic (expanding) blood pressure measurements. The accuracy of the method depends on the physician's skill in interpreting the sounds. Hospitals sometimes employ a more accurate procedure, but it is "invasive," involving insertion of a catheter in the artery.

Precision gimballed mirror control in remote sensing LIDAR for environmental monitoring

NASA Astrophysics Data System (ADS)

Singh, Ravindra; Mudgil, Ashwani; Prakash, Chandra; Pal, Suranjan

2006-12-01

Differential Absorption Lidar (DIAL) Systems are advantageously used to detect and measure very small concentrations of trace gases in the atmosphere. There is a requirement to interrogate and search for the presence of one or more of toxic agents out of a large number (about 20 or so) of possible agents at distances up to several kilometers with the help of a ground-based multi-wavelength DIAL system employing pulsed, tunable laser sources in the wavelength bands of 2-5 micron and 9.2-10.8 micron. The Laser beams from the two sources are directed in the atmosphere with a predefined divergence to scan the atmosphere. Two methodologies can be implemented to provide the beam steering, one is to mount the entire telescope of transmitting and receiving channel on to a motorized gimbal platform and second is to keep the optical telescope stationary and use a slewing mirror to steer the beam in required direction. The first scheme is named as mass control and second scheme is called mirror control. Both the schemes have relative advantages and disadvantages and in the present DIAL application second scheme is being adopted. The present opto-mechanical configuration of DIAL system employs a 700 x 500 mm 2 (Elliptical) steering mirror for transmitting the collimated beams in a required direction and receiving the reflected beam as well. In the receiving channel a Telescope is used which collects the return beam and focuses the same on to a detector. The slewing mirror is housed in a gimbal mount having a sufficient FOR (Field of Regard) in Azimuth and elevation plane. The paper describes the modeling and simulation of Opto-mechanical and servo-mechanical subsystems of precision gimbaled mirror and also discusses the issues related to design of control system. The requirement specifications in regard to field of regard, slew rates 5°/s, scanning rates 1°/s are to be met with stringent beam pointing and scanning accuracies. The design of this system is categorized as multidisciplinary problem. The design parameters obtained from opto-mechanical analysis forms the input for control system design. The design of control system is carried out using conventional design methodologies.

Mobile SO2 and NO2 DIAL Lidar system for enforcement use

NASA Astrophysics Data System (ADS)

Cunningham, David L.; Pence, William H.; Moody, Stephen E.

1994-06-01

A self-contained mobile differential absorption lidar (DIAL) system intended for measuring SO2 and NO2 concentrations from stationary combustion sources has been completed for enforcement use. The system uses tunable Ti:sapphire laser technology, with nonlinear conversion to the blue and UV absorption wavelengths. Separate tunable laser oscillators at slightly offset wavelengths are pumped on alternate pulses of a 20 Hz doubled Nd:YAG pump laser; the outputs are amplified in a common amplifier, doubled or tripled, and transmitted toward a target region via a two-mirror beam director. Scattered atmospheric returns are collected in a 0.27-m-diameter telescope, detected with a filtered photomultiplier, and digitized and stored for analysis. Extensive software-based control and display windows are provided for operator interaction with the system. The DIAL system is built into a small motor coach. Gasoline- powered electrical generation, laser cooling, and air conditioning services are present. Separate computers are provided for simultaneous data collection and data analysis activities, with shared data base access. A laser printer supplies hardcopy output. The system includes the capability for automatic data collection at a series of scanner angles, and computer processing to present results in a variety of formats. Plumes from coal-fired and mixed-fuel-fired combusters have been examined for NO2 and SO2 content. Noise levels of a few parts per million are reached with averaging times of less than one minute.

Effects of historical and predictive information on ability of transport pilot to predict an alert

NASA Technical Reports Server (NTRS)

Trujillo, Anna C.

1994-01-01

In the aviation community, the early detection of the development of a possible subsystem problem during a flight is potentially useful for increasing the safety of the flight. Commercial airlines are currently using twin-engine aircraft for extended transport operations over water, and the early detection of a possible problem might increase the flight crew's options for safely landing the aircraft. One method for decreasing the severity of a developing problem is to predict the behavior of the problem so that appropriate corrective actions can be taken. To investigate the pilots' ability to predict long-term events, a computer workstation experiment was conducted in which 18 airline pilots predicted the alert time (the time to an alert) using 3 different dial displays and 3 different parameter behavior complexity levels. The three dial displays were as follows: standard (resembling current aircraft round dial presentations); history (indicating the current value plus the value of the parameter 5 sec in the past); and predictive (indicating the current value plus the value of the parameter 5 sec into the future). The time profiles describing the behavior of the parameter consisted of constant rate-of-change profiles, decelerating profiles, and accelerating-then-decelerating profiles. Although the pilots indicated that they preferred the near term predictive dial, the objective data did not support its use. The objective data did show that the time profiles had the most significant effect on performance in estimating the time to an alert.

An update on 'dose calibrator' settings for nuclides used in nuclear medicine.

PubMed

Bergeron, Denis E; Cessna, Jeffrey T

2018-06-01

Most clinical measurements of radioactivity, whether for therapeutic or imaging nuclides, rely on commercial re-entrant ionization chambers ('dose calibrators'). The National Institute of Standards and Technology (NIST) maintains a battery of representative calibrators and works to link calibration settings ('dial settings') to primary radioactivity standards. Here, we provide a summary of NIST-determined dial settings for 22 radionuclides. We collected previously published dial settings and determined some new ones using either the calibration curve method or the dialing-in approach. The dial settings with their uncertainties are collected in a comprehensive table. In general, current manufacturer-provided calibration settings give activities that agree with National Institute of Standards and Technology standards to within a few percent.

A new differential absorption lidar to measure sub-hourly fluctuation of tropospheric ozone profiles in the Baltimore-Washington DC region

NASA Astrophysics Data System (ADS)

Sullivan, J. T.; McGee, T. J.; Sumnicht, G. K.; Twigg, L. W.; Hoff, R. M.

2014-04-01

Tropospheric ozone profiles have been retrieved from the new ground based National Aeronautics and Space Administration (NASA) Goddard Space Flight Center TROPospheric OZone DIfferential Absorption Lidar (GSFC TROPOZ DIAL) in Greenbelt, MD (38.99° N, 76.84° W, 57 m a.s.l.) from 400 m to 12 km a.g.l. Current atmospheric satellite instruments cannot peer through the optically thick stratospheric ozone layer to remotely sense boundary layer tropospheric ozone. In order to monitor this lower ozone more effectively, the Tropospheric Ozone Lidar Network (TOLNet) has been developed, which currently consists of five stations across the US. The GSFC TROPOZ DIAL is based on the Differential Absorption Lidar (DIAL) technique, which currently detects two wavelengths, 289 and 299 nm. Ozone is absorbed more strongly at 289 nm than at 299 nm. The DIAL technique exploits this difference between the returned backscatter signals to obtain the ozone number density as a function of altitude. The transmitted wavelengths are generated by focusing the output of a quadrupled Nd:YAG laser beam (266 nm) into a pair of Raman cells, filled with high pressure hydrogen and deuterium. Stimulated Raman Scattering (SRS) within the focus generates a significant fraction of the pump energy at the first Stokes shift. With the knowledge of the ozone absorption coefficient at these two wavelengths, the range resolved number density can be derived. An interesting atmospheric case study involving the Stratospheric-Tropospheric Exchange (STE) of ozone is shown to emphasize the regional importance of this instrument as well as assessing the validation and calibration of data. The retrieval yields an uncertainty of 16-19% from 0-1.5 km, 10-18% from 1.5-3 km, and 11-25% from 3 km to 12 km. There are currently surface ozone measurements hourly and ozonesonde launches occasionally, but this system will be the first to make routine tropospheric ozone profile measurements in the Baltimore-Washington DC area.

A New Differential Absorption Lidar to Measure Sub-Hourly Fluctuation of Tropospheric Ozone Profiles in the Baltimore - Washington D.C. Region

NASA Technical Reports Server (NTRS)

Sullivan, J. T.; McGee, T. J.; Sumnicht, G. K.; Twigg, L. W.; Hoff, R. M.

2014-01-01

Tropospheric ozone profiles have been retrieved from the new ground based National Aeronautics and Space Administration (NASA) Goddard Space Flight Center TROPospheric OZone DIfferential Absorption Lidar (GSFC TROPOZ DIAL) in Greenbelt, MD (38.99 N, 76.84 W, 57 meters ASL) from 400 m to 12 km AGL. Current atmospheric satellite instruments cannot peer through the optically thick stratospheric ozone layer to remotely sense boundary layer tropospheric ozone. In order to monitor this lower ozone more effectively, the Tropospheric Ozone Lidar Network (TOLNet) has been developed, which currently consists of five stations across the US. The GSFC TROPOZ DIAL is based on the Differential Absorption Lidar (DIAL) technique, which currently detects two wavelengths, 289 and 299 nm. Ozone is absorbed more strongly at 289 nm than at 299 nm. The DIAL technique exploits this difference between the returned backscatter signals to obtain the ozone number density as a function of altitude. The transmitted wavelengths are generated by focusing the output of a quadrupled Nd:YAG laser beam (266 nm) into a pair of Raman cells, filled with high pressure hydrogen and deuterium. Stimulated Raman Scattering (SRS) within the focus generates a significant fraction of the pump energy at the first Stokes shift. With the knowledge of the ozone absorption coefficient at these two wavelengths, the range resolved number density can be derived. An interesting atmospheric case study involving the Stratospheric-Tropospheric Exchange (STE) of ozone is shown to emphasize the regional importance of this instrument as well as assessing the validation and calibration of data. The retrieval yields an uncertainty of 16-19 percent from 0-1.5 km, 10-18 percent from 1.5-3 km, and 11-25 percent from 3 km to 12 km. There are currently surface ozone measurements hourly and ozonesonde launches occasionally, but this system will be the first to make routine tropospheric ozone profile measurements in the Baltimore-Washington DC area.

Monitoring Tropospheric Ozone Enhancement in the Front Range Using the Gsfc Tropoz DIAL during Discover - AQ 2014

NASA Astrophysics Data System (ADS)

Sullivan, J. T.; McGee, T. J.; Hoff, R. M.; Twigg, L.; Sumnicht, G. K.

2014-12-01

Tropospheric ozone profiles have been retrieved from the new ground based National Aeronautics and Space Administration (NASA) Goddard Space Flight Center TROPospheric OZone DIfferential Absorption Lidar (GSFC TROPOZ DIAL) in Fort Collins, CO from 200 m to 16 km AGL. These measurements were taken as part of NASA's DISCOVER-AQ campaign in July/August 2014. Measurements were made during simultaneous aircraft spirals over the lidar site as well as collocated ozonesonde launches. Ozone enhancement from local sources typically occurred in the mid-afternoon convection period, especially when there was light winds and low cloud cover. Interesting ozone profiles and time series data will be shown. Current atmospheric satellite instruments cannot peer through the optically thick stratospheric ozone layer to remotely sense boundary layer tropospheric ozone. In order to monitor this lower ozone more effectively, the Tropospheric Ozone Lidar Network (TOLNet) has been developed, which currently consists of five stations across the US. Three of these lidars, including the GSFC TROPOZ DIAL, recorded measurements during the DISCOVER-AQ campaign. The GSFC TROPOZ DIAL is based on the Differential Absorption Lidar (DIAL) technique, which currently detects two wavelengths, 289 and 299 nm. Ozone is absorbed more strongly at 289 nm than at 299 nm. The DIAL technique exploits this difference between the returned backscatter signals to obtain the ozone number density as a function of altitude. The transmitted wavelengths are generated by focusing the output of a quadrupled Nd:YAG laser beam (266 nm) into a pair of Raman cells, filled with high pressure hydrogen and deuterium. Stimulated Raman Scattering (SRS) within the focus generates a significant fraction of the pump energy at the first Stokes shift. With the knowledge of the ozone absorption coefficient at these two wavelengths, the range resolved number density can be derived.

Compact Ozone Differential Absorption Lidar (DIAL) Transmitter Using Solid-State Dye Polymers

NASA Technical Reports Server (NTRS)

Jones, Alton L., Jr.; DeYoung, Russell J.; Elsayid-Ele, Hani

2001-01-01

A new potential DIAL laser transmitter is described that uses solid-state dye laser materials to make a simpler, more compact, lower mass laser system. Two solid-state dye laser materials were tested to evaluate their performance in a laser oscillator cavity end pumped by a pulsed Nd:YAG laser at 532 nm. The polymer host polymethyl-methacrylate was injected with a pyrromethene laser dye, PM 580, or PM 597. A narrowband laser oscillator cavity was constructed to produce visible wavelengths of 578 and 600 nm which were frequency doubled into the UV region (299 or 300 nm) by using a BBO crystal, resulting in a maximum energy of 11 mJ at a wavelength of 578 nm when pumped by the Nd:YAG laser at an energy of 100 mJ (532 nm). A maximum output energy of 378 microJ was achieved in the UV region at a wavelength of 289 nm but lasted only 2000 laser shots at a repetition rate of 10 Hz. The results are promising and show that a solid-state dye laser based ozone DIAL system is possible with improvements in the design of the laser transmitter.

Advanced Water Vapor Lidar Detection System

NASA Technical Reports Server (NTRS)

Elsayed-Ali, Hani

1998-01-01

In the present water vapor lidar system, the detected signal is sent over long cables to a waveform digitizer in a CAMAC crate. This has the disadvantage of transmitting analog signals for a relatively long distance, which is subjected to pickup noise, leading to a decrease in the signal to noise ratio. Generally, errors in the measurement of water vapor with the DIAL method arise from both random and systematic sources. Systematic errors in DIAL measurements are caused by both atmospheric and instrumentation effects. The selection of the on-line alexandrite laser with a narrow linewidth, suitable intensity and high spectral purity, and its operation at the center of the water vapor lines, ensures minimum influence in the DIAL measurement that are caused by the laser spectral distribution and avoid system overloads. Random errors are caused by noise in the detected signal. Variability of the photon statistics in the lidar return signal, noise resulting from detector dark current, and noise in the background signal are the main sources of random error. This type of error can be minimized by maximizing the signal to noise ratio. The increase in the signal to noise ratio can be achieved by several ways. One way is to increase the laser pulse energy, by increasing its amplitude or the pulse repetition rate. Another way, is to use a detector system with higher quantum efficiency and lower noise, on the other hand, the selection of a narrow band optical filter that rejects most of the day background light and retains high optical efficiency is an important issue. Following acquisition of the lidar data, we minimize random errors in the DIAL measurement by averaging the data, but this will result in the reduction of the vertical and horizontal resolutions. Thus, a trade off is necessary to achieve a balance between the spatial resolution and the measurement precision. Therefore, the main goal of this research effort is to increase the signal to noise ratio by a factor of 10 over the current system, using a newly evaluated, very low noise avalanche photo diode detector and constructing a 10 MHz waveform digitizer which will replace the current CAMAC system.

Implementation and flight tests for the Digital Integrated Automatic Landing System (DIALS). Part 1: Flight software equations, flight test description and selected flight test data

NASA Technical Reports Server (NTRS)

Hueschen, R. M.

1986-01-01

Five flight tests of the Digital Automated Landing System (DIALS) were conducted on the Advanced Transport Operating Systems (ATOPS) Transportation Research Vehicle (TSRV) -- a modified Boeing 737 aircraft for advanced controls and displays research. These flight tests were conducted at NASA's Wallops Flight Center using the microwave landing system (MLS) installation on runway 22. This report describes the flight software equations of the DIALS which was designed using modern control theory direct-digital design methods and employed a constant gain Kalman filter. Selected flight test performance data is presented for localizer (runway centerline) capture and track at various intercept angles, for glideslope capture and track of 3, 4.5, and 5 degree glideslopes, for the decrab maneuver, and for the flare maneuver. Data is also presented to illustrate the system performance in the presence of cross, gust, and shear winds. The mean and standard deviation of the peak position errors for localizer capture were, respectively, 24 feet and 26 feet. For mild wind conditions, glideslope and localizer tracking position errors did not exceed, respectively, 5 and 20 feet. For gusty wind conditions (8 to 10 knots), these errors were, respectively, 10 and 30 feet. Ten hands off automatic lands were performed. The standard deviation of the touchdown position and velocity errors from the mean values were, respectively, 244 feet and 0.7 feet/sec.

LASE measurements of water vapor and aerosol profiles during the Plains Elevated Convection at Night (PECAN) field experiment

NASA Astrophysics Data System (ADS)

Nehrir, A. R.; Ferrare, R. A.; Kooi, S. A.; Butler, C. F.; Notari, A.; Hair, J. W.; Collins, J. E., Jr.; Ismail, S.

2015-12-01

The Lidar Atmospheric Sensing Experiment (LASE) system was deployed on the NASA DC-8 aircraft during the Plains Elevated Convection At Night (PECAN) field experiment, which was conducted during June-July 2015 over the central and southern plains. LASE is an active remote sensor that employs the differential absorption lidar (DIAL) technique to measure range resolved profiles of water vapor and aerosols above and below the aircraft. The DC-8 conducted nine local science flights from June 30- July 14 where LASE sampled water vapor and aerosol fields in support of the PECAN primary science objectives relating to better understanding nocturnal Mesoscale Convective Systems (MCSs), Convective Initiation (CI), the Low Level Jet (LLJ), bores, and to compare different airborne and ground based measurements. LASE observed large spatial and temporal variability in water vapor and aerosol distributions in advance of nocturnal MCSs, across bores resulting from MCS outflow boundaries, and across the LLJ associated with the development of MCSs and CI. An overview of the LASE data collected during the PECAN field experiment will be presented where emphasis will be placed on variability of water vapor profiles in the vicinity of severe storms and intense convection in the central and southern plains. Preliminary comparisons show good agreement between coincident LASE and radiosonde water vapor profiles. In addition, an advanced water vapor DIAL system being developed at NASA Langley will be discussed.

Rater agreement reliability of the dial test in the ACL-deficient knee.

PubMed

Slichter, Malou E; Wolterbeek, Nienke; Auw Yang, K Gie; Zijl, Jacco A C; Piscaer, Tom M

2018-06-14

Posterolateral rotatory instability (PLRI) of the knee can easily be missed, because attention is paid to injury of the cruciate ligaments. If left untreated this clinical instability may persist after reconstruction of the cruciate ligaments and may put the graft at risk of failure. Even though the dial test is widely used to diagnose PLRI, no validity and reliability studies of the manual dial test are yet performed in patients. This study focuses on the reliability of the manual dial test by determining the rater agreement. Two independent examiners performed the dial test in knees of 52 patients after knee distorsion with a suspicion on ACL rupture. The dial test was performed in prone position in 30°, 60° and 90° of flexion of the knees. ≥10° side-to-side difference was considered a positive dial test. For quantification of the amount of rotation in degrees, a measuring device was used with a standardized 6 Nm force, using a digital torque adapter on a booth. The intra-rater, inter-rater and rater-device agreement were determined by calculating kappa (κ) for the dial test. A positive dial test was found in 21.2% and 18.0% of the patients as assessed by a blinded examiner and orthopaedic surgeon respectively. Fair inter-rater agreement was found in 30° of flexion, κ F  = 0.29 (95% CI: 0.01 to 0.56), p = 0.044 and 90° of flexion, κ F  = 0.38 (95% CI: 0.10 to 0.66), p = 0.007. Almost perfect rater-device agreement was found in 30° of flexion, κ C  = 0.84 (95% CI: 0.52 to 1.15), p < 0.001. Moderate rater-device agreement was found in 30° and 90° combined, κ C  = 0.50 (95% CI: 0.13 to 0.86), p = 0.008. No significant intra-rater agreement was found. Rater agreement reliability of the manual dial test is questionable. It has a fair inter-rater agreement in 30° and 90° of flexion.

Preschool children adapt grasping movements to upcoming object manipulations: Evidence from a dial rotation task.

PubMed

Herbort, Oliver; Büschelberger, Juliane; Janczyk, Markus

2018-03-01

In adults, the motor plans for object-directed grasping movements reflects the anticipated requirements of intended future object manipulations. This prospective mode of planning has been termed second-order planning. Surprisingly, second-order planning is thought to be fully developed only by 10 years of age, when children master seemingly more complex motor skills. In this study, we tested the hypothesis that already 5- and 6-year-old children consistently use second-order planning but that this ability does not become apparent in tasks that are traditionally used to probe it. We asked 5- and 6-year-olds and adults to grasp and rotate a circular dial in a clockwise or counterclockwise direction. Although children's grasp selections were less consistent on an intra- and inter-individual level than adults' grasp selections, all children adjusted their grasps to the upcoming dial rotations. By contrast, in an also administered bar rotation task, only a subset of children adjusted their grasps to different bar rotations, thereby replicating previous results. The results indicate that 5- and 6-year-olds consistently use second-order planning in a dial rotation task, although this ability does not become apparent in bar rotation tasks. Copyright © 2017 Elsevier Inc. All rights reserved.

New laser design for NIR lidar applications

NASA Astrophysics Data System (ADS)

Vogelmann, H.; Trickl, T.; Perfahl, M.; Biggel, S.

2018-04-01

Recently, we quantified the very high spatio-temporal short term variability of tropospheric water vapor in a three dimensional study [1]. From a technical point of view this also depicted the general requirement of short integration times for recording water-vapor profiles with lidar. For this purpose, the only suitable technique is the differential absorption lidar (DIAL) working in the near-infrared (NIR) spectral region. The laser emission of most water vapor DIAL systems is generated by Ti:sapphire or alexandrite lasers. The water vapor absorption band at 817 nm is predominated for the use of Ti:sapphire. We present a new concept of transversely pumping in a Ti:Sapphire amplification stage as well as a compact laser design for the generation of single mode NIR pulses with two different DIAL wavelengths inside a single resonator. This laser concept allows for high output power due to repetitions rates up to 100Hz or even more. It is, because of its compactness, also suitable for mobile applications.

Calculus, Radio Dials and the Straight-Line Frequency Variable Capacitor

ERIC Educational Resources Information Center

Boyadzhiev, Khristo N.

2010-01-01

Most often radio dials of analogue radios are not uniformly graded; the frequencies are cramped on the left side or on the right side. This makes tuning more difficult. Why are dials made this way? We shall see here that simple calculus can help understand this problem and solve it. (Contains 7 figures.)

On Ramps: Options and Issues in Accessing the Internet.

ERIC Educational Resources Information Center

Bocher, Bob

1995-01-01

Outlines the basic options that schools and libraries have for accessing the Internet, focusing on four models: direct connection; dial access using SLIP/PPP (Serial Line Internet Protocol/Point-to-Point Protocol); dial-up using terminal emulation mode; and dial access through commercial online services. Discusses access option issues such as…

ERDC-CERL LD-870 Download Program Developed for Aberdeen Test Center: User’s Manual

DTIC Science & Technology

2007-05-01

Conexant 56k internal modem , supplied by Dell, different Rockwell chipset The current modem string is: AT&F X4 E0 Q0 V1 T M0 W2 S0=5 S12=0 &D2 &W...noise monitors. It provides a trouble- shooting guide for resolving known issues with the monitoring system and contains information regarding modem ...20 Unit is dialed, modem responds with “No Carrier

Airborne 2-Micron Double-Pulsed Integrated Path Differential Absorption Lidar for Column CO2 Measurement

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Yu, Jirong; Petros, Mulugeta; Refaat, Tamer F.; Remus, Ruben G.; Fay, James J.; Reithmaier, Karl

2014-01-01

Double-pulse 2-micron lasers have been demonstrated with energy as high as 600 millijouls and up to 10 Hz repetition rate. The two laser pulses are separated by 200 microseconds and can be tuned and locked separately. Applying double-pulse laser in DIAL system enhances the CO2 measurement capability by increasing the overlap of the sampled volume between the on-line and off-line. To avoid detection complicity, integrated path differential absorption (IPDA) lidar provides higher signal-to-noise ratio measurement compared to conventional range-resolved DIAL. Rather than weak atmospheric scattering returns, IPDA rely on the much stronger hard target returns that is best suited for airborne platforms. In addition, the IPDA technique measures the total integrated column content from the instrument to the hard target but with weighting that can be tuned by the transmitter. Therefore, the transmitter could be tuned to weight the column measurement to the surface for optimum CO2 interaction studies or up to the free troposphere for optimum transport studies. Currently, NASA LaRC is developing and integrating a double-Pulsed 2-micron direct detection IPDA lidar for CO2 column measurement from an airborne platform. The presentation will describe the development of the 2-micron IPDA lidar system and present the airborne measurement of column CO2 and will compare to in-situ measurement for various ground target of different reflectivity.

Goals for Postsecondary Instructional Delivery Systems.

ERIC Educational Resources Information Center

Knapp, Stuart E.; Valentine, Carol A.

Extrapolating from the trends in postsecondary instructional delivery systems identified by Brown, Lewis and Harcleroad, this report attempts to identify how these trends might be implemented in Oregon. Separating the systems into technology-centered and people-centered, the report proposes future applications of dial access systems, self learning…

Development and Experimental Verification of a High Resolution, Tunable LIDAR Computer Simulation Model for Atmospheric Laser Remote Sensing

NASA Astrophysics Data System (ADS)

Wilcox, William Edward, Jr.

1995-01-01

A computer program (LIDAR-PC) and associated atmospheric spectral databases have been developed which accurately simulate the laser remote sensing of the atmosphere and the system performance of a direct-detection Lidar or tunable Differential Absorption Lidar (DIAL) system. This simulation program allows, for the first time, the use of several different large atmospheric spectral databases to be coupled with Lidar parameter simulations on the same computer platform to provide a real-time, interactive, and easy to use design tool for atmospheric Lidar simulation and modeling. LIDAR -PC has been used for a range of different Lidar simulations and compared to experimental Lidar data. In general, the simulations agreed very well with the experimental measurements. In addition, the simulation offered, for the first time, the analysis and comparison of experimental Lidar data to easily determine the range-resolved attenuation coefficient of the atmosphere and the effect of telescope overlap factor. The software and databases operate on an IBM-PC or compatible computer platform, and thus are very useful to the research community for Lidar analysis. The complete Lidar and atmospheric spectral transmission modeling program uses the HITRAN database for high-resolution molecular absorption lines of the atmosphere, the BACKSCAT/LOWTRAN computer databases and models for the effects of aerosol and cloud backscatter and attenuation, and the range-resolved Lidar equation. The program can calculate the Lidar backscattered signal-to-noise for a slant path geometry from space and simulate the effect of high resolution, tunable, single frequency, and moderate line width lasers on the Lidar/DIAL signal. The program was used to model and analyze the experimental Lidar data obtained from several measurements. A fixed wavelength, Ho:YSGG aerosol Lidar (Sugimoto, 1990) developed at USF and a tunable Ho:YSGG DIAL system (Cha, 1991) for measuring atmospheric water vapor at 2.1 μm were analyzed. The simulations agreed very well with the measurements, and also yielded, for the first time, the ability to easily deduce the atmospheric attentuation coefficient, alpha, from the Lidar data. Simulations and analysis of other Lidar measurements included that of a 1.57 mu m OPO aerosol Lidar system developed at USF (Harrell, 1995) and of the NASA LITE (Laser-in-Space Technology Experiment) Lidar recently flown in the Space shuttle. Finally, an extensive series of laboratory experiments were made with the 1.57 μm OPO Lidar system to test calculations of the telescope/laser overlap and the effect of different telescope sizes and designs. The simulations agreed well with the experimental data for the telescope diameter and central obscuration test cases. The LIDAR-PC programs are available on the Internet from the USAF Lidar Home Page Web site, http://www.cas.usf.edu/physics/lidar.html/.

Response Rates in Random-Digit-Dialed Telephone Surveys: Estimation vs. Measurement.

ERIC Educational Resources Information Center

Franz, Jennifer D.

The efficacy of the random digit dialing method in telephone surveys was examined. Random digit dialing (RDD) generates a pure random sample and provides the advantage of including unlisted phone numbers, as well as numbers which are too new to be listed. Its disadvantage is that it generates a major proportion of nonworking and business…

[Remote access to a web-based image distribution system].

PubMed

Bergh, B; Schlaefke, A; Frankenbach, R; Vogl, T J

2004-06-01

To assess different network and security technologies for remote access to a web-based image distribution system of a hospital intranet. Following preparatory testing, the time-to-display (TTD) was measured for three image types (CR, CT, MR). The evaluation included two remote access technologies consisting of direct ISDN-Dial-Up or VPN connection (Virtual Private Network), with three different connection speeds of 64, 128 (ISDN) and 768 Kbit/s (ADSL-Asymmetric Digital Subscriber Line), as well as with lossless and lossy compression. Depending on the image type, the TTD with lossless compression for 64 Kbit/s varied from 1 : 00 to 2 : 40 minutes, for 128 Kbit/s from 0 : 35 to 1 : 15 minutes and for ADSL from 0 : 15 to 0 : 45 minutes. The ISDN-Dial-Up connection was superior to VPN technology at 64 Kbit/s but did not allow higher connection speeds. Lossy compression reduced the TTD by half for all measurements. VPN technology is preferable to direct Dial-Up connections since it offers higher connection speeds and advantages in usage and security. For occasional usage, 128 Kbit/s (ISDN) can be considered sufficient, especially in conjunction with lossy compression. ADSL should be chosen when a more frequent usage is anticipated, whereby lossy compression may be omitted. Due to higher bandwidths and improved usability, the web-based approach appears superior to conventional teleradiology systems.

Analysis of diffential absorption lidar technique for measurements of anhydrous hydrogen chloride from solid rocket motors using a deuterium fluoride laser

NASA Technical Reports Server (NTRS)

Bair, C. H.; Allario, F.

1977-01-01

An active optical technique (differential absorption lidar (DIAL)) for detecting, ranging, and quantifying the concentration of anhydrous HCl contained in the ground cloud emitted by solid rocket motors (SRM) is evaluated. Results are presented of an experiment in which absorption coefficients of HCl were measured for several deuterium fluoride (DF) laser transitions demonstrating for the first time that a close overlap exists between the 2-1 P(3) vibrational transition of the DF laser and the 1-0 P(6) absorption line of HCl, with an absorption coefficient of 5.64 (atm-cm) to the -1 power. These measurements show that the DF laser can be an appropriate radiation source for detecting HCl in a DIAL technique. Development of a mathematical computer model to predict the sensitivity of DIAL for detecting anhydrous HCl in the ground cloud is outlined, and results that assume a commercially available DF laser as the radiation source are presented.

Open Source Service Agent (OSSA) in the intelligence community's Open Source Architecture

NASA Technical Reports Server (NTRS)

Fiene, Bruce F.

1994-01-01

The Community Open Source Program Office (COSPO) has developed an architecture for the intelligence community's new Open Source Information System (OSIS). The architecture is a multi-phased program featuring connectivity, interoperability, and functionality. OSIS is based on a distributed architecture concept. The system is designed to function as a virtual entity. OSIS will be a restricted (non-public), user configured network employing Internet communications. Privacy and authentication will be provided through firewall protection. Connection to OSIS can be made through any server on the Internet or through dial-up modems provided the appropriate firewall authentication system is installed on the client.

Insulin Delivery System

NASA Technical Reports Server (NTRS)

1988-01-01

When Programmable Implantable Medication System (PIMS) is implanted in human body, it delivers precise programmed amounts of insulin over long periods of time. Mini-Med Technologies has been refining the Technologies since initial development at APL. The size of a hockey puck, and encased in titanium shell, PIMS holds about 2 1/2 teaspoons of insulin at a programmed basal rate. If a change in measured blood sugar level dictates a different dose, the patient can vary the amount of insulin delivered by holding a small radio transceiver over the implanted system and dialing in a specific program held in the PIMS computer memory. Insulin refills are accomplished approximately 4 times a year by hypodermic needle.

DEFENSE RTD&E ONLINE SYSTEM (DROLS)

EPA Science Inventory

Web Enabled DROLS (WED) is a free subscription service available to registered users that provides online access to DTIC's Technical Reports and Research Summaries Databases. It replaces the former unclassified dial-up access to DROLS, DTIC's Defense RDT&E Online System. The Defe...

ASV3 dial-in interface recommendation for the Repository Based Software Engineering (RBSE) program

NASA Technical Reports Server (NTRS)

1992-01-01

The purpose of this report is to provide insight into the approach and design of the Cooperative User Interface (CUI). The CUI is being developed based on Hypercard technology and will provide the same look and feel as is provided by the NASA Electronic Library System (NELS) X-Window interface. The interaction between the user and ASCII-LIB is presented as well as the set of Hypercard Cards with which the user will work.

Fiber-Optic Gratings for Lidar Measurements of Water Vapor

NASA Technical Reports Server (NTRS)

Vann, Leila B.; DeYoung, Russell J.

2006-01-01

Narrow-band filters in the form of phase-shifted Fabry-Perot Bragg gratings incorporated into optical fibers are being developed for differential-absorption lidar (DIAL) instruments used to measure concentrations of atmospheric water vapor. The basic idea is to measure the relative amounts of pulsed laser light scattered from the atmosphere at two nearly equal wavelengths, one of which coincides with an absorption spectral peak of water molecules and the other corresponding to no water vapor absorption. As part of the DIAL measurement process, the scattered light is made to pass through a filter on the way to a photodetector. Omitting other details of DIAL for the sake of brevity, what is required of the filter is to provide a stop band that: Surrounds the water-vapor spectral absorption peaks at a wavelength of 946 nm, Has a spectral width of at least a couple of nanometers, Contains a pass band preferably no wider than necessary to accommodate the 946.0003-nm-wavelength water vapor absorption peak [which has 8.47 pm full width at half maximum (FWHM)], and Contains another pass band at the slightly shorter wavelength of 945.9 nm, where there is scattering of light from aerosol particles but no absorption by water molecules. Whereas filters used heretofore in DIAL have had bandwidths of =300 pm, recent progress in the art of fiber-optic Bragg-grating filters has made it feasible to reduce bandwidths to less than or equal to 20 pm and thereby to reduce background noise. Another benefit of substituting fiber-optic Bragg-grating filters for those now in use would be significant reductions in the weights of DIAL instruments. Yet another advantage of fiber-optic Bragg-grating filters is that their transmission spectra can be shifted to longer wavelengths by heating or stretching: hence, it is envisioned that future DIAL instruments would contain devices for fine adjustment of transmission wavelengths through stretching or heating of fiber-optic Bragg-grating filters nominally designed and fabricated to have transmission wavelengths that, in the absence of stretching, would be slightly too short.

Development of a Pulsed 2-micron Laser Transmitter for CO2 Sensing from Space

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Yu, Jirong; Bai, Yingxin; Petros, Mulugeta; Menzies, Robert T.

2011-01-01

NASA Langley Research Center (LaRC), in collaboration with NASA Jet Propulsion Laboratory (JPL), is engaged in the development and demonstration of a highly efficient, versatile, 2-micron pulsed laser that can be used in a pulsed Differential Absorption Lidar (DIAL)/Integrated Path Differential Absorption (IPDA) instrument to make precise, high-resolution CO2 measurements to investigate sources, sinks, and fluxes of CO2. This laser transmitter will feature performance characteristics needed for an ASCENDS system that will be capable of delivering the CO2 measurement precision required by the Earth Science Decadal Survey (DS).

I 5683 you: dialing phone numbers on cell phones activates key-concordant concepts.

PubMed

Topolinski, Sascha

2011-03-01

When people perform actions, effects associated with the actions are activated mentally, even if those effects are not apparent. This study tested whether sequences of simulations of virtual action effects can be integrated into a meaning of their own. Cell phones were used to test this hypothesis because pressing a key on a phone is habitually associated with both digits (dialing numbers) and letters (typing text messages). In Experiment 1, dialing digit sequences induced the meaning of words that share the same key sequence (e.g., 5683, LOVE). This occurred even though the letters were not labeled on the keypad, and participants were not aware of the digit-letter correspondences. In Experiment 2, subjects preferred dialing numbers implying positive words (e.g., 37326, DREAM) over dialing numbers implying negative words (e.g., 75463, SLIME). In Experiment 3, subjects preferred companies with phone numbers implying a company-related word (e.g., LOVE for a dating agency, CORPSE for a mortician) compared with companies with phone numbers implying a company-unrelated word.

2-Micron Triple-Pulse Integrated Path Differential Absorption Lidar Development for Simultaneous Airborne Column Measurements of Carbon Dioxide and Water Vapor in the Atmosphere

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Petros, Mulugeta; Refaat, Tamer F.; Yu, Jirong

2016-01-01

For more than 15 years, NASA Langley Research Center (LaRC) has contributed in developing several 2-micron carbon dioxide active remote sensors using the DIAL technique. Currently, an airborne 2-micron triple-pulse integrated path differential absorption (IPDA) lidar is under development at NASA LaRC. This paper focuses on the advancement of the 2-micron triple-pulse IPDA lidar development. Updates on the state-of-the-art triple-pulse laser transmitter will be presented including the status of wavelength control, packaging and lidar integration. In addition, receiver development updates will also be presented, including telescope integration, detection systems and data acquisition electronics. Future plan for IPDA lidar system for ground integration, testing and flight validation will be presented.

47 CFR 32.2341 - Large private branch exchanges.

Code of Federal Regulations, 2014 CFR

2014-10-01

... UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32... cost of installation, of multiple manual private branch exchanges and of dial system private branch...) Embedded CPE is that equipment or inventory which is tariffed or otherwise subject to the jurisdictional...

47 CFR 32.2341 - Large private branch exchanges.

Code of Federal Regulations, 2011 CFR

2011-10-01

... UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32... cost of installation, of multiple manual private branch exchanges and of dial system private branch...) Embedded CPE is that equipment or inventory which is tariffed or otherwise subject to the jurisdictional...

47 CFR 32.2341 - Large private branch exchanges.

Code of Federal Regulations, 2013 CFR

2013-10-01

... UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32... cost of installation, of multiple manual private branch exchanges and of dial system private branch...) Embedded CPE is that equipment or inventory which is tariffed or otherwise subject to the jurisdictional...

47 CFR 32.2341 - Large private branch exchanges.

Code of Federal Regulations, 2012 CFR

2012-10-01

... UNIFORM SYSTEM OF ACCOUNTS FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32... cost of installation, of multiple manual private branch exchanges and of dial system private branch...) Embedded CPE is that equipment or inventory which is tariffed or otherwise subject to the jurisdictional...

Synthesis of Kentucky's traveler information systems.

DOT National Transportation Integrated Search

2016-08-01

After the United States Department of Transportation (USDOT) petitioned the Federal Communications Commission (FCC) to establish a dedicated phone number for real-time travel information services, the abbreviated 511 dialing code was founded in July ...

Synthesis of Kentucky's traveler information systems.

DOT National Transportation Integrated Search

2016-08-01

After the United States Department of Transportation (USDOT) petitioned the Federal Communications Commission (FCC) to establish : a dedicated phone number for real-time travel information services, the abbreviated 511 dialing code was founded in Jul...

Measurements of Water Vapor Profiles with Compact DIAL in the Tokyo Metropolitan Area

NASA Astrophysics Data System (ADS)

Abo, Makoto; Sakai, Tetsu; Le Hoai, Phong Pham; Shibata, Yasukuni; Nagasawa, Chikao

2018-04-01

In recent years, the frequency of occurrence of locally heavy rainfall that can cause extensive damages, has been increasing in Japan. For early prediction of heavy rainfall, it is useful to measure the water vapor vertical distribution upwind cumulus convection beforehand. For that purpose, we have been developing compact water vapor differential absorption lidar (DIAL). We show the results of the measurements with lidar in summer when the local heavy rainfall frequently occurs in Japan. We also show the preliminary result of the assimilation of the lidar data to the numerical model and impact on the heavy rainfall prediction.

Tunable Single-Frequency Near IR Lasers for DIAL Applications

NASA Technical Reports Server (NTRS)

Henderson, Sammy W.; Marquardt, John H.; Carrig, Timothy J.; Gatt, Phil; Smith, Duane D.; Hale, Charley P.

2000-01-01

Tunable single-frequency sources in the 2-4 micron wavelength region are useful for remote DIAL measurements of chemicals and pollutants. We are developing tunable single-frequency transmitters and receivers for both direct and coherent detection lidar measurement applications. We have demonstrated a direct-diode-pumped PPLN-based OPO that operates single frequency, produces greater than 10 mW cw and is tunable over the 2.5 - 3.9 micron wavelength region. This laser has been used to injection seed a pulsed PPLN OPO, pumped by a 1.064 micron Nd:YAG laser, producing 50-100 microJoule single-frequency pulses at 100 Hz PRF near 3.6 micron wavelength. In addition, we have demonstrated a cw Cr:ZnSe laser that is tunable over the 2.1 - 2.8 micron wavelength region. This laser is pumped by a cw diode-pumped Tm:YALO laser and has produced over 1.8 W cw. Tm- and Tm, Ho-doped single-frequency solid-state lasers that produce over 50 mW cw and are tunable over approximately 10 nm in the 2 -2.1 micron band with fast PZT tuning have also been demonstrated. A fast PZT-tunable Tm, Ho:YLF laser was used for a direct-detection column content DIAL measurement of atmospheric CO2. Modeling shows that that all these cw and pulsed sources are useful for column-content coherent DIAL measurements at several km range using topographic targets.

InGaAsSb Detectors' Characterization for 2-Micron CO2 Lidar/DIAL Applications

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Abedin, M. Nurul; Koch, Grady J.; Singh, Upendra N.

2003-01-01

Recent interest in monitoring atmospheric CO2 focuses attention on infrared remote sensing using the 2-micron lidar/differential absorption lidar (DIAL) technique. Quantum detectors are critical components in this technique, and many research efforts concentrate on developing such devices for the 2-micron wavelength. Characterization results of InGaAsSb quantum detectors for the 2-micron wavelength range are presented, including experimental setup and procedure. Detectors are prototype devices manufactured by using separate absorption and multiplication (SAM) structures. Characterization experiments include V-I measurements, spectral response and its variation with bias voltage and temperature, noise measurements, noise-equivalent-power (NEP) and detectivity calculations, and signal-to-noise ratio (SNR) estimation. A slight increase in the output signal occurred with increased bias voltage and was associated with a noise level increase. Cooling down the detectors reduces noise and shifts the cutoff wavelength to shorter values. Further improvement in the design and manufacturing process, by increasing the device gain and lowering its noise level, is necessary to meet the required CO2 lidar/DIAL specifications.

Mechanisms of breathing instability in patients with obstructive sleep apnea.

PubMed

Younes, Magdy; Ostrowski, Michele; Atkar, Raj; Laprairie, John; Siemens, Andrea; Hanly, Patrick

2007-12-01

The response to chemical stimuli (chemical responsiveness) and the increases in respiratory drive required for arousal (arousal threshold) and for opening the airway without arousal (effective recruitment threshold) are important determinants of ventilatory instability and, hence, severity of obstructive apnea. We measured these variables in 21 obstructive apnea patients (apnea-hypopnea index 91 +/- 24 h(-1)) while on continuous-positive-airway pressure. During sleep, pressure was intermittently reduced (dial down) to induce severe hypopneas. Dial downs were done on room air and following approximately 30 s of breathing hypercapneic and/or hypoxic mixtures, which induced a range of ventilatory stimulation before dial down. Ventilation just before dial down and flow during dial down were measured. Chemical responsiveness, estimated as the percent increase in ventilation during the 5(th) breath following administration of 6% CO(2) combined with approximately 4% desaturation, was large (187 +/- 117%). Arousal threshold, estimated as the percent increase in ventilation associated with a 50% probability of arousal, ranged from 40% to >268% and was <120% in 12/21 patients, indicating that in many patients arousal occurs with modest changes in chemical drive. Effective recruitment threshold, estimated as percent increase in pre-dial-down ventilation associated with a significant increase in dial-down flow, ranged from zero to >174% and was <110% in 12/21 patients, indicating that in many patients reflex dilatation occurs with modest increases in drive. The two thresholds were not correlated. In most OSA patients, airway patency may be maintained with only modest increases in chemical drive, but instability results because of a low arousal threshold and a brisk increase in drive following brief reduction in alveolar ventilation.

Solid-state Raman frequency converters for CO2-DIAL systems at 1.6 μm

NASA Astrophysics Data System (ADS)

Rhee, Hanjo; Lisinetskii, Victor; Kaminskii, Alexander A.; Eichler, Hans-Joachim

2009-09-01

Measurement of the three-dimensional distribution of atmospheric trace gases, especially CO2, is an important factor to improve the accuracy of climate models and to understand the global effects of the greenhouse effect. This can be achieved by differential absorption Lidar (DIAL). The absorption spectrum of CO2 features several suitable absorption lines for a ground-based or air-borne DIAL system working at wavelengths between 1.57 μm and 1.61 μm. An appropriate laser transmitter must emit laser pulses with pulse energies of more than 10 mJ and pulse duration in the nanosecond range. For high spectral purity the bandwidth is required to be less than 60 MHz. OPOs and Er-doped solid-state lasers emit around 1.6 μm, but we describe here alternatively Nd:YAG and Nd:glass laser systems with Raman converters. The use of stimulated Raman scattering in crystalline and ceramic materials is a possibility to shift the wavelength of existing lasers depending on the size of the Raman shift. After the investigation of a large number of Raman-active materials some of them could be identified as promising candidates for the conversion of typical Nd:YAG emission wavelengths, including LiNH2C6H4SO3•H2O, Ba(NO3)2, Li2SO4•H2O, Y(HCOO)3•2H2O, β-BBO and diamond. Our experiments with Ba(NO3)2 showed that the choice of the material should not be restricted to those with an adequate first order Stokes Raman line position, but also second or third order Raman shift should be considered. Development of Raman frequency converters for high pulse energies concentrates on linear and folded resonator designs and seeded Raman amplifiers using the Raman material as a direct amplifier. With Ba(NO3)2 pulse energy up to 116 mJ and 42 % quantum efficiency at the third Stokes wavelength with 1599 nm has been demonstrated. High power operation at 5 W with compensation of thermal lensing was achieved.

Linear operating region in the ozone dial photon counting system

NASA Technical Reports Server (NTRS)

Andrawis, Madeleine

1995-01-01

Ozone is a relatively unstable molecule found in Earth's atmosphere. An ozone molecule is made up of three atoms of oxygen. Depending on where ozone resides, it can protect or harm life on Earth. High in the atmosphere, about 15 miles up, ozone acts as a shield to protect Earth's surface from the sun's harmful ultraviolet radiation. Without this shield, we would be more susceptible to skin cancer, cataracts, and impaired immune systems. Closer to Earth, in the air we breathe, ozone is a harmful pollutant that causes damage to lung tissue and plants. Since the early 1980's, airborne lidar systems have been used for making measurements of ozone. The differential absorption lidar (DIAL) technique is used in the remote measurement of O3. This system allows the O3 to be measured as function of the range in the atmosphere. Two frequency-doubled Nd:YAG lasers are used to pump tunable dye lasers. The lasers are operating at 289 nm for the DIAL on-line wavelength of O3, and the other one is operated at 300 nm for the off-line wavelength. The DIAL wavelengths are produced in sequential laser pulses with a time separation of 300 micro s. The backscattered laser energy is collected by telescopes and measured using photon counting systems. The photon counting system measures the light signal by making use of the photon nature of light. The output pulse from the Photo-Multiplier Tube (PE), caused by a photon striking the PMT photo-cathode, is amplified and passed to a pulse height discriminator. The peak value of the pulse is compared to a reference voltage (discrimination level). If the pulse amplitude exceeds the discrimination level, the discriminator generates a standard pulse which is counted by the digital counter. Non-linearity in the system is caused by the overlapping of pulses and the finite response time of the electronics. At low count rates one expects the system to register one event for each output pulse from the PMT corresponding to a photon incident upon the photocathode, however, at higher rates the limitations of the discrimination/counting system will cause the observed count rate to be non-linear with respect to the true count rate. Depending on the pulse height distribution and the discriminator level, the overlapping of pulses (pulse pile-up) can cause count loss or even an additional apparent count gain as the signal levels increase. Characterization of the system, including the pulse height distribution, the signal to noise ratio, and the effect of the discriminator threshold level, is critical in maximizing the linear operating region of the system, thus greatly increasing the useful dynamic range of the system.

Fire Effects Information System: New engine, remodeled interior, added options

Treesearch

Jane Kapler Smith

2010-01-01

Some of today's firefighters weren't even born when the Fire Effects Information System (FEIS) (Web site ) "hit the streets" in 1986. Managers might remember using a dial-up connection in the early 1990s to access information on biology, ecology, and fire offered by FEIS.

Putting the Medical Library Online: Electronic Bulletin Boards. . . and Beyond.

ERIC Educational Resources Information Center

Kittle, Paul W.

1985-01-01

Describes use of microcomputers with system called "TBBS" ("The Bread Board System") at Loma Linda University Medical Center to allow users enhanced services from home, whether library facilities are open or not. Flexibility and security, dialing into medical library, and suggestions for setting up similar computerized…

Calling for Help? Considering Function and Meaning when Patients Drunk-Dial Psychotherapists

PubMed Central

Serafini, Kelly; LaPaglia, Donna; Steinfeld, Matthew

2013-01-01

Drunk-dialing is a term documented in both popular culture and academic literatures to describe a behavior in which a person contacts another individual by phone while intoxicated. In our collective clinical experience we have found that clients drunk-dial their clinicians too, particularly while in substance use treatment, and yet there is a noticeable absence of research on the topic to guide clinical decision-making within a process-based understanding of these events. As the parameters within which psychotherapy takes place become increasingly technologized, a literature base to document clients’ idiosyncratic use of technology will become increasingly necessary and useful. We provide a brief review of the existing research on drunk-dialing and conclude with specific questions to guide future research and practice. PMID:24023519

REMOTE: Modem Communicator Program for the IBM personal computer

DOE Office of Scientific and Technical Information (OSTI.GOV)

McGirt, F.

1984-06-01

REMOTE, a Modem Communicator Program, was developed to provide full duplex serial communication with arbitrary remote computers via either dial-up telephone modems or direct lines. The latest version of REMOTE (documented in this report) was developed for the IBM Personal Computer.

77 FR 61574 - National Climate Assessment and Development Advisory Committee; Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-10

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration National Climate Assessment... National Climate Assessment and Development Advisory Committee (NCADAC). DATES: Time and Date: The meeting... to dial into the call. Please check the National Climate Assessment Web site for additional...

Dial-in Topological Metamaterials Based on Bistable Stewart Platform.

PubMed

Wu, Ying; Chaunsali, Rajesh; Yasuda, Hiromi; Yu, Kaiping; Yang, Jinkyu

2018-01-08

Recently, there have been significant efforts to guide mechanical energy in structures by relying on a novel topological framework popularized by the discovery of topological insulators. Here, we propose a topological metamaterial system based on the design of the Stewart Platform, which can not only guide mechanical waves robustly in a desired path, but also can be tuned in situ to change this wave path at will. Without resorting to any active materials, the current system harnesses bistablilty in its unit cells, such that tuning can be performed simply by a dial-in action. Consequently, a topological transition mechanism inspired by the quantum valley Hall effect can be achieved. We show the possibility of tuning in a variety of topological and traditional waveguides in the same system, and numerically investigate key qualitative and quantitative differences between them. We observe that even though both types of waveguides can lead to significant wave transmission for a certain frequency range, topological waveguides are distinctive as they support robust, back scattering immune, one-way wave propagation.

Water vapour emission in vegetable fuel: absorption cell measurements and detection limits of our CO II Dial system

NASA Astrophysics Data System (ADS)

Bellecci, C.; De Leo, L.; Gaudio, P.; Gelfusa, M.; Lo Feudo, T.; Martellucci, S.; Richetta, M.

2006-09-01

Forest fires can be the cause of serious environmental and economic damages. For this reason a considerable effort has been directed toward the forest protection and fire fighting. In the early forest fire detection, Lidar technique present considerable advantages compared to the passive detection methods based on infrared cameras currently in common use, due its higher sensitivity and ability to accurately locate the fire. The combustion phase of the vegetable matter causes a great amount of water vapour emission, thus the water molecule behaviour will be studied to obtain a fire detection system ready and efficient also before the flame propagation. A first evaluation of increment of the water vapour concentration compared to standard one will be estimated by a numerical simulation. These results will be compared with the experimental measurements carried out into a cell with a CO II Dial system, burning different kinds of vegetable fuel. Our results and their comparison will be reported in this paper.

A robust optical parametric oscillator and receiver telescope for differential absorption lidar of greenhouse gases

NASA Astrophysics Data System (ADS)

Robinson, Iain; Jack, James W.; Rae, Cameron F.; Moncrieff, John B.

2015-10-01

We report the development of a differential absorption lidar instrument (DIAL) designed and built specifically for the measurement of anthropogenic greenhouse gases in the atmosphere. The DIAL is integrated into a commercial astronomical telescope to provide high-quality receiver optics and enable automated scanning for three-dimensional lidar acquisition. The instrument is portable and can be set up within a few hours in the field. The laser source is a pulsed optical parametric oscillator (OPO) which outputs light at a wavelength tunable near 1.6 μm. This wavelength region, which is also used in telecommunications devices, provides access to absorption lines in both carbon dioxide at 1573 nm and methane at 1646 nm. To achieve the critical temperature stability required for a laserbased field instrument the four-mirror OPO cavity is machined from a single aluminium block. A piezoactuator adjusts the cavity length to achieve resonance and this is maintained over temperature changes through the use of a feedback loop. The laser output is continuously monitored with pyroelectric detectors and a custom-built wavemeter. The OPO is injection seeded by a temperature-stabilized distributed feedback laser diode (DFB-LD) with a wavelength locked to the absorption line centre (on-line) using a gas cell containing pure carbon dioxide. A second DFB-LD is tuned to a nearby wavelength (off-line) to provide the reference required for differential absorption measurements. A similar system has been designed and built to provide the injection seeding wavelengths for methane. The system integrates the DFB-LDs, drivers, locking electronics, gas cell and balanced photodetectors. The results of test measurements of carbon dioxide are presented and the development of the system is discussed, including the adaptation required for the measurement of methane.

77 FR 56191 - National Climate Assessment and Development Advisory Committee (NCADAC)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-12

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration National Climate Assessment... National Climate Assessment and Development Advisory Committee (NCADAC). DATES: The meeting will be held... dial into the call. Please check the National Climate Assessment Web site for additional information at...

In-cell measurements of smoke backscattering coefficients using a CO2 laser system for application to lidar-dial forest fire detection

NASA Astrophysics Data System (ADS)

Bellecci, Carlo; Gaudio, Pasquale; Gelfusa, Michela; Lo Feudo, Teresa; Murari, Andrea; Richetta, Maria; de Leo, Leonerdo

2010-12-01

In the lidar-dial method, the amount of the water vapor present in the smoke of the vegetable fuel is detected to reduce the number of false alarms. We report the measurements of the smoke backscattering coefficients for the CO2 laser lines 10R20 and 10R18 as determined in an absorption cell for two different vegetable fuels (eucalyptus and conifer). These experimental backscattering coefficients enable us to determine the error to be associated to the water vapor measurements when the traditional first-order approximation is assumed. We find that this first-order approximation is valid for combustion rates as low as 100 g/s.

The effect of cell phone use on postural balance and mobility in older compared to young adults.

PubMed

Laatar, Rabeb; Kachouri, Hiba; Borji, Rihab; Rebai, Haithem; Sahli, Sonia

2017-05-01

Cell phone use is considered as an essential part of everyday life saturating all age groups and demographics. This study aimed to explore the effect of various cell phone functions on postural control and mobility in the elderly. Twenty healthy older (mean age 72.5±2.9) and twenty young (26.3±2.8) adults participated in this study. Postural balance was assessed by measuring the center of pressure (CoP) displacement with (talking on a cell phone (CONVERSE), dialing a number (DIAL) and listening to music (MUSIC)) and without cell phone use. Mobility was assessed by the Timed Up and Go Test (TUGT). Results showed that for both groups, the CoP parameters increased significantly during the CONVERSE (p<0.001) and the DIAL (CoP area , CoP X : p<0.05; CoP Y : p<0.01) conditions compared to the control condition. Moreover, the CoP area values were significantly higher during the CONVERSE condition in comparison to the DIAL (p<0.05) one. In older adults, the TUGT scores increased significantly in the DIAL (p<0.01) condition compared to the CONVERSE and the MUSIC conditions. In conclusion, cell phone use impairs similarly standing postural balance of elderly and young adults. Interestingly, in the elderly, all cell phone functions used altered mobility with the dialing function causing the largest mobility deterioration. Copyright © 2017 Elsevier Inc. All rights reserved.

Tunable solid-state laser technology for applications to scientific and technological experiments from space

NASA Technical Reports Server (NTRS)

Allario, F.; Taylor, L. V.

1986-01-01

Current plans for the Earth Observing System (EOS) include development of a lidar facility to conduct scientific experiments from a polar orbiting platforms. A recommended set of experiments were scoped, which includes techniques of atmospheric backscatter (Lidar), Differential Absorption Lidar (DIAL), altimetry, and retroranging. Preliminary assessments of the resources (power, weight, volume) required by the Eos Lidar Facility were conducted. A research program in tunable solid state laser technology was developed, which includes laser materials development, modeling and experiments on the physics of solid state laser materials, and development of solid state laser transmitters with a strong focus on Eos scientific investigations. Some of the system studies that were conducted which highlight the payoff of solid state laser technology for the Eos scientific investigations will be discussed. Additionally, a summary of some promising research results which have recently emerged from the research program will be presented.

49 CFR Appendix D to Part 37 - Construction and Interpretation of Provisions of 49 CFR Part 37

Code of Federal Regulations, 2011 CFR

2011-10-01

... direction of service that will help to comply with post-January 1992 requirements. A recipient that severely..., like a typical city bus system or a dial-a-ride van system, fit clearly into one category or the other. Other systems may not so clearly fall into one of the categories. Nevertheless, because how a system is...

The necessity of clinical application of tibial reduction for detection of underestimated posterolateral rotatory instability in combined posterior cruciate ligament and posterolateral corner deficient knee.

PubMed

Lee, Han-Jun; Park, Yong-Beom; Ko, Young-Bong; Kim, Seong-Hwan; Kwon, Hyeok-Bin; Yu, Dong-Seok; Jung, Young-Bok

2015-10-01

The purpose of this study was to evaluate the usefulness of tibial reduction during dial test for clinical detection of underestimated posterolateral rotatory instability (PLRI) in combined posterior cruciate ligament (PCL)-posterolateral corner (PLC) deficient knee in terms of external rotation laxity and clinical outcomes. Twenty-one patients who classified as grade I PLRI using dial test with subluxated tibia, but classified as grade II with tibial reduction evaluated retrospectively. The mean follow-up was 39.3 months (range 24-61 months). Each patient was evaluated by the following variables: posterior translation and varus laxity on radiograph, KT-1000 arthrometer, dial test (reduced and subluxated position), International Knee Documentation Committee, Orthopädische Arbeitsgruppe Knie scoring system and Tegner activity scale. There were significant improvements in posterior tibial translation (8.6 ± 2.0 to 2.1 ± 1.0 mm; P < 0.001), varus laxity (3.3 ± 1.3 to 1.4 ± 0.5 mm; P < 0.001) and external rotation (13.2° ± 0.8° to 3.6° ± 1.1° at 30°, 13.3° ± 0.9° to 3.6° ± 0.9° at 90°; P < 0.001). The clinical scores were improved significantly at the last follow-up (P < 0.001). The external tibial rotation during dial test with tibial reduction increased from 6.8° ± 0.9 to 13.2° ± 0.8° at 30° of knee flexion, from 7.0° ± 0.8° to 13.3° ± 0.9° at 90° (P < 0.001). The clinical application of reduction of posteriorly subluxated tibia during the dial test was essential for an appropriate treatment of underestimated PLRI in combined PCL-PLC deficient knee. Retrospective case series, Level IV.

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2012 CFR

2012-01-01

... between the temperature control dial and the thermometer readings at each major (numbered) dial division... block of suitable conductivity with a cylindrical depression, or sample cup, over which is fitted a...

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2011 CFR

2011-01-01

... between the temperature control dial and the thermometer readings at each major (numbered) dial division... block of suitable conductivity with a cylindrical depression, or sample cup, over which is fitted a...

16 CFR 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2014 CFR

2014-01-01

... between the temperature control dial and the thermometer readings at each major (numbered) dial division... block of suitable conductivity with a cylindrical depression, or sample cup, over which is fitted a...

Differential Absorption Lidar to Measure Sub-Hourly Variation of Tropospheric Ozone Profiles

NASA Technical Reports Server (NTRS)

Kuang, Shi; Burris, John F.; Newchurch, Michael J.; Johnson, Steve; Long, Stephanie

2009-01-01

A tropospheric ozone Differential Absorption Lidar (DIAL) system, developed jointly by the University of Alabama at Huntsville and NASA, is making regular observations of ozone vertical distributions between 1 and 8 km with two receivers under both daytime and nighttime conditions using lasers at 285 and 291 nm. This paper describes the lidar system and analysis technique with some measurement examples. An iterative aerosol correction procedure reduces the retrieval error arising from differential aerosol backscatter in the lower troposphere. Lidar observations with coincident ozonesonde flights demonstrate that the retrieval accuracy ranges from better than 10% below 4 km to better than 20% below 8 km with 750-m vertical resolution and 10-min temporal integration

Development and application of a Controlled Release Facility (CRF) to validate flux quantifying methodologies.

NASA Astrophysics Data System (ADS)

Helmore, Jonathan

2017-04-01

The National Physical Laboratory, the UK's National Measurement Institute, has developed a novel facility capable of replicating the gaseous emission flux characteristics of a variety of real-word scenarios as may be found in small to medium scale industry and agriculture. The Controlled Release Facility (CRF) can be used to challenge conventional remote sensing techniques, as well as validate new Unmanned Aerial Vehicle (UAV) and distributed sensor network based methods, for source identification and flux calculation. The CRF method will be described and the results from three case studies will be discussed: The replication of an operational on-shore shale gas well using emissions of natural gas to atmosphere and measurements using Differential Absorption LIDAR (DIAL); the replication of fugitive volatile organic compounds emissions from a petrochemical unit and measurements using DIAL; and the replication of methane and carbon dioxide emissions from landfill and measurements using both fixed wing and multi-rotor UAVs.

Phonological and Non-Phonological Language Skills as Predictors of Early Reading Performance

ERIC Educational Resources Information Center

Batson-Magnuson, LuAnn

2010-01-01

Accurate prediction of early childhood reading performance could help identify at-risk students, aid in the development of evidence-based intervention strategies, and further our theoretical understanding of reading development. This study assessed the validity of the Developmental Indicator for the Assessment of Learning (DIAL) language-based…

78 FR 64481 - National Climate Assessment and Development Advisory Committee (NCADAC)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-29

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration National Climate Assessment... National Climate Assessment and Development Advisory Committee (NCADAC). Time and Date: The meeting will be... public will not be able to dial into the call. Please check the National Climate Assessment Web site for...

78 FR 51711 - National Climate Assessment and Development Advisory Committee (NCADAC)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-21

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration National Climate Assessment... National Climate Assessment and Development Advisory Committee (NCADAC). Time and Date: The meeting will be... public will not be able to dial into the call. Please check the National Climate Assessment Web site for...

78 FR 21598 - National Climate Assessment and Development Advisory Committee (NCADAC)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-11

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration National Climate Assessment... National Climate Assessment and Development Advisory Committee (NCADAC). Time and Date: The meeting will be... public will not be able to dial into the call. Please check the National Climate Assessment Web site for...

16 CFR § 1500.43a - Method of test for flashpoint of volatile flammable materials.

Code of Federal Regulations, 2013 CFR

2013-01-01

... between the temperature control dial and the thermometer readings at each major (numbered) dial division... block of suitable conductivity with a cylindrical depression, or sample cup, over which is fitted a...

Tunable lasers for water vapor measurements and other lidar applications

NASA Technical Reports Server (NTRS)

Gammon, R. W.; Mcilrath, T. J.; Wilkerson, T. D.

1977-01-01

A tunable dye laser suitable for differential absorption (DIAL) measurements of water vapor in the troposphere was constructed. A multi-pass absorption cell for calibration was also constructed for use in atmospheric DIAL measurements of water vapor.

A Fiber-Optic Coupled Telescope for Water Vapor DIAL Receivers

NASA Technical Reports Server (NTRS)

DeYoung, Russell J.; Lonn, Frederick

1998-01-01

A fiber-optic coupled telescope of low complexity was constructed and tested. The major loss mechanisms of the optical system have been characterized. Light collected by the receiver mirror is focused onto an optical fiber, and the output of the fiber is filtered by an interference filter and then focused onto an APD detector. This system was used in lidar field measurements with a 532-nm Nd:YAG laser beam. The results were encouraging. A numerical model used for calculation of the expected return signal agreed with the lidar return signal obtained. The assembled system was easy to align and operate and weighed about 8 kg for a 30 cm (12") mirror system. This weight is low enough to allow mounting of the fiber-optic telescope receiver system in a UAV. Furthermore, the good agreement between the numerical lidar model and the performance of the actual receiver system, suggests that this model may be used for estimation of the performance of this and other lidar systems in the future. Such telescopes are relatively easy to construct and align. The fiber optic cable allows easy placement of the optical detector in any position. These telescope systems should find widespread use in aircraft and space home DIAL water vapor receiver systems.

A Fast, Locally Adaptive, Interactive Retrieval Algorithm for the Analysis of DIAL Measurements

NASA Astrophysics Data System (ADS)

Samarov, D. V.; Rogers, R.; Hair, J. W.; Douglass, K. O.; Plusquellic, D.

2010-12-01

Differential absorption light detection and ranging (DIAL) is a laser-based tool which is used for remote, range-resolved measurement of particular gases in the atmosphere, such as carbon-dioxide and methane. In many instances it is of interest to study how these gases are distributed over a region such as a landfill, factory, or farm. While a single DIAL measurement only tells us about the distribution of a gas along a single path, a sequence of consecutive measurements provides us with information on how that gas is distributed over a region, making DIAL a natural choice for such studies. DIAL measurements present a number of interesting challenges; first, in order to convert the raw data to concentration it is necessary to estimate the derivative along the path of the measurement. Second, as the distribution of gases across a region can be highly heterogeneous it is important that the spatial nature of the measurements be taken into account. Finally, since it is common for the set of collected measurements to be quite large it is important for the method to be computationally efficient. Existing work based on Local Polynomial Regression (LPR) has been developed which addresses the first two issues, but the issue of computational speed remains an open problem. In addition to the latter, another desirable property is to allow user input into the algorithm. In this talk we present a novel method based on LPR which utilizes a variant of the RODEO algorithm to provide a fast, locally adaptive and interactive approach to the analysis of DIAL measurements. This methodology is motivated by and applied to several simulated examples and a study out of NASA Langley Research Center (LaRC) looking at the estimation of aerosol extinction in the atmosphere. A comparison study of our method against several other algorithms is also presented. References Chaudhuri, P., Marron, J.S., Scale-space view of curve estimation, Annals of Statistics 28 (2000) 408-428. Duong, T., Cowling, A., Koch, I., Wand, M.P., Feature significance for multivariate kernel density estimation, Computational Statistics and Data Analysis 52 (2008) 4225-4242. Godtliebsen, F., Marron, J.S., Chaudhuri, P., Statistical Significance of features in digital images, Image and Vision Computing 22 (2004) 1093-1104. Lafferty, J., Wasserman, L., RODEO: Sparse, Greedy Nonparametric Regression, Annals of Statistics 36 (2008) 28-63. Lindstrom, T., Holst, U., Weibring, P., Analysis of lidar fields using local polynomial regression, Environmetrics 16 (2005) 619-634

Autonomous dial-a-ride transit. Part 1, technical overview

DOT National Transportation Integrated Search

1998-11-01

Is autonomous-dial-a-ride (ADART) and idea whose time has come with the advent of technologies. This report describes the essential features of an experimental ADART service and establishes a context for ADART implementation based on urban transit in...

Phoenix Transit Sunday Dial-a-Ride

DOT National Transportation Integrated Search

1983-06-01

A local taxi operator began subsidized dial-a-ride service in Phoenix, AR, when the city found that Sunday fixed-route transit service would be more costly. Regular cabs and wheelchair vans are billed at a fixed hourly rate less fares collected. Over...

A Novel High Efficient Laser Transmitter Design for a Space-borne Ozone Differential Lidar (DIAL)

NASA Technical Reports Server (NTRS)

Edwards, W. C.; Chen, S.; Petway, L. B.; Marsh, W. D.; Storm, M. E.; Barnes, J. C.

2000-01-01

Development of a UV laser transmitter capable of operating from a space platform is a critical step in enabling global earth observations of aerosols and ozone at resolutions greater than current passive instrument capabilities. Tropospheric chemistry is well recognized as the next frontier for global atmospheric measurement. NASA Langley Research Center (LaRC) and the Canadian Space Agency (CSA) have jointly studied the requirements for a satellite based, global ozone monitoring instrument. The study, called Ozone Research using Advanced Cooperative Lidar Experiment (ORACLE) has defined the Differential Absorption Lidar (DIAL) instrument performance, weight and power, and configuration requirements for a space based measurement. In order to achieve the measurement resolution and acceptable signal-to-noise from lidar returns, 500mJ/pulse (5 Watts average power) is required at both 305-308nm and 315-320nm wavelengths. These are consecutive pulses, in a 10 Hz, double-pulsed format. The two wavelengths are used as the on- and off-lines for the ozone DIAL measurement. NASA Langley is currently developing technology for a UV laser transmitter capable of meeting the ORACLE requirements. Experimental efforts to date have shown that the UV generation scheme is viable, and that energies greater than l00mJ/pulse are possible. In this paper, we will briefly discuss the down select process for the proposed laser design, the study effort to date and the laser system design, including both primary and alternate approaches. We will describe UV laser technology that minimizes the total number of optical components (for enhanced reliability) as well as the number of UV coated optics required to transmit the light from the laser (for enhanced optical damage resistance). While the goal is to develop a laser that will produce 500 mJ of energy, we will describe an optional design that will produce output energies between 100 - 200 mJ/unit and techniques for combining multiple laser modules in order to transmit a minimum of 500mJ of UV energy in each pulse of the on- and off-line pulse pairs. This modular laser approach provides redundancy and significantly reduces development time, risk and cost when compared to the development of a single, 500mJ double-pulsed laser subsystem. Finally, we will summarize the laser development effort to date, including results that include the highest known UV energy ( 130 mJ at 320nm) ever produced by a solid-state laser operating in this wavelength region.

47 CFR 68.318 - Additional limitations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... TERMINAL EQUIPMENT TO THE TELEPHONE NETWORK Conditions for Terminal Equipment Approval § 68.318 Additional... incorporate the specified features. (b) Registered terminal equipment with automatic dialing capability. (1... proceeding to dial another number. (6) Network addressing signals shall be transmitted no earlier than: (i...

47 CFR 68.318 - Additional limitations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... TERMINAL EQUIPMENT TO THE TELEPHONE NETWORK Conditions for Terminal Equipment Approval § 68.318 Additional... incorporate the specified features. (b) Registered terminal equipment with automatic dialing capability. (1... proceeding to dial another number. (6) Network addressing signals shall be transmitted no earlier than: (i...

47 CFR 68.318 - Additional limitations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... TERMINAL EQUIPMENT TO THE TELEPHONE NETWORK Conditions for Terminal Equipment Approval § 68.318 Additional... incorporate the specified features. (b) Registered terminal equipment with automatic dialing capability. (1... proceeding to dial another number. (6) Network addressing signals shall be transmitted no earlier than: (i...

47 CFR 68.318 - Additional limitations.

Code of Federal Regulations, 2013 CFR

2013-10-01

... TERMINAL EQUIPMENT TO THE TELEPHONE NETWORK Conditions for Terminal Equipment Approval § 68.318 Additional... incorporate the specified features. (b) Registered terminal equipment with automatic dialing capability. (1... proceeding to dial another number. (6) Network addressing signals shall be transmitted no earlier than: (i...

47 CFR 68.318 - Additional limitations.

Code of Federal Regulations, 2014 CFR

2014-10-01

... TERMINAL EQUIPMENT TO THE TELEPHONE NETWORK Conditions for Terminal Equipment Approval § 68.318 Additional... incorporate the specified features. (b) Registered terminal equipment with automatic dialing capability. (1... proceeding to dial another number. (6) Network addressing signals shall be transmitted no earlier than: (i...

Inexpensive E-mail Systems for LANs and Dial-up.

ERIC Educational Resources Information Center

Pfaffman, Jay

Internet e-mail is becoming more accessible to K-12 teachers. Many colleges and universities will give accounts to teachers for the price of asking. Unfortunately, many of these university systems are hard to use and are usually not offered to K-12 students. Also, most schools do not have phone lines in classrooms. This paper discusses two systems…

47 CFR 95.1313 - Interconnection prohibited.

Code of Federal Regulations, 2010 CFR

2010-10-01

... points in the wireline or radio network of a public telephone company and persons served by multi-use... licensees or other authorized persons for transmitter control (including dial-up transmitter control circuits) or as an integral part of an authorized, private, internal system of communication or as an...

Verification of rut depth collected with the INO laser rut measurement system : executive summary report.

DOT National Transportation Integrated Search

2011-10-28

Since 1985, ODOT has been manually collecting rut : depth data using a straight edge and dial gauge (S&G). This : method is slow and dangerous to pavement condition raters : when traffic control is not available. According to the : Pavement Condition...

Correlation of DIAL Ozone Observations with Lightning

NASA Technical Reports Server (NTRS)

Peterson, Harold; Kuang, Shi; Koshak, William; Newchurch, Michael

2014-01-01

The purpose of this project is to see whether ozone maxima measured by the DIfferential Absorption Lidar (DIAL) instrument in Huntsville, AL may be traced back to lightning events occurring 24-48 hours beforehand. The methodology is to start with lidar measurements of ozone from DIAL. The HYbrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model is then used to determine the origin of these ozone maxima 24-48 hours prior. Data from the National Lightning Detection Network (NLDN) are used to examine the presence/absence of lightning along the trajectory. This type of analysis suggests that lightning-produced NOx may be responsible for some of the ozone maxima over Huntsville.

Mobile lidar system for environmental monitoring

NASA Astrophysics Data System (ADS)

Zhao, Guangyu; Lian, Ming; Li, Yiyun; Duan, Zheng; Zhu, Shiming; Svanberg, Sune

2018-04-01

A versatile mobile remote sensing system for multidisciplinary environmental monitoring tasks on the Chinese scene is described. The system includes a 20 Hz Nd:YAG laser-pumped dye laser, optical transmitting/receiving systems with a 30 cm and a 40 cm Newtonian telescope, and electronics, all integrated in a laboratory, installed on a Jiefang truck. Results from field experiments on atomic mercury DIAL mapping and remote laser-induced fluorescence and break-down spectroscopy are given.

10 CFR 30.15 - Certain items containing byproduct material.

Code of Federal Regulations, 2010 CFR

2010-01-01

... electrical currents. (9) Ionizing radiation measuring instruments containing, for purposes of internal... material and not exceeding the following specified levels of radiation: (i) 25 millicuries of tritium per... considered as part of the dial), (vii) The levels of radiation from hands and dials containing promethium 147...

Accuracy and consistency of weights provided by home bathroom scales.

PubMed

Yorkin, Meredith; Spaccarotella, Kim; Martin-Biggers, Jennifer; Quick, Virginia; Byrd-Bredbenner, Carol

2013-12-17

Self-reported body weight is often used for calculation of Body Mass Index because it is easy to collect. Little is known about sources of error introduced by using bathroom scales to measure weight at home. The objective of this study was to evaluate the accuracy and consistency of digital versus dial-type bathroom scales commonly used for self-reported weight. Participants brought functioning bathroom scales (n=18 dial-type, n=43 digital-type) to a central location. Trained researchers assessed accuracy and consistency using certified calibration weights at 10 kg, 25 kg, 50 kg, 75 kg, 100 kg, and 110 kg. Data also were collected on frequency of calibration, age and floor surface beneath the scale. All participants reported using their scale on hard surface flooring. Before calibration, all digital scales displayed 0, but dial scales displayed a mean absolute initial weight of 0.95 (1.9 SD) kg. Digital scales accurately weighed test loads whereas dial-type scale weights differed significantly (p<0.05). Imprecision of dial scales was significantly greater than that of digital scales at all weights (p<0.05). Accuracy and precision did not vary by scale age. Digital home bathroom scales provide sufficiently accurate and consistent weights for public health research. Reminders to zero scales before each use may further improve accuracy of self-reported weight.

A mobile differential absorption lidar to measure sub-hourly fluctuation of tropospheric ozone profiles in the Baltimore-Washington, D.C. region

NASA Astrophysics Data System (ADS)

Sullivan, J. T.; McGee, T. J.; Sumnicht, G. K.; Twigg, L. W.; Hoff, R. M.

2014-10-01

Tropospheric ozone profiles have been retrieved from the new ground-based National Aeronautics and Space Administration (NASA) Goddard Space Flight Center TROPospheric OZone DIfferential Absorption Lidar (GSFC TROPOZ DIAL) in Greenbelt, MD (38.99° N, 76.84° W, 57 m a.s.l.), from 400 m to 12 km a.g.l. Current atmospheric satellite instruments cannot peer through the optically thick stratospheric ozone layer to remotely sense boundary layer tropospheric ozone. In order to monitor this lower ozone more effectively, the Tropospheric Ozone Lidar Network (TOLNet) has been developed, which currently consists of five stations across the US. The GSFC TROPOZ DIAL is based on the DIAL technique, which currently detects two wavelengths, 289 and 299 nm, with multiple receivers. The transmitted wavelengths are generated by focusing the output of a quadrupled Nd:YAG laser beam (266 nm) into a pair of Raman cells, filled with high-pressure hydrogen and deuterium, using helium as buffer gas. With the knowledge of the ozone absorption coefficient at these two wavelengths, the range-resolved number density can be derived. An interesting atmospheric case study involving the stratospheric-tropospheric exchange (STE) of ozone is shown, to emphasize the regional importance of this instrument as well as to assess the validation and calibration of data. There was a low amount of aerosol aloft, and an iterative aerosol correction has been performed on the retrieved data, which resulted in less than a 3 ppb correction to the final ozone concentration. The retrieval yields an uncertainty of 16-19% from 0 to 1.5 km, 10-18% from 1.5 to 3 km, and 11-25% from 3 to 12 km according to the relevant aerosol concentration aloft. There are currently surface ozone measurements hourly and ozonesonde launches occasionally, but this system will be the first to make routine tropospheric ozone profile measurements in the Baltimore-Washington, D.C. area.

NOAA TELEPHONE RECORDINGS

Science.gov Websites

! Boating Safety Beach Hazards Rip Currents Hypothermia Hurricanes Thunderstorms Lightning Coastal Flooding . Mariners can now hear the latest coastal and offshore weather observations using Dial-A-Buoy. Dial-A-Buoy wind and wave measurements taken within the last hour at 65 buoy and 54 Coastal-Marine Automated

Securing TCP/IP and Dial-up Access to Administrative Data.

ERIC Educational Resources Information Center

Conrad, L. Dean

1992-01-01

This article describes Arizona State University's solution to security risk inherent in general access systems such as TCP/IP (Transmission Control Protocol/INTERNET Protocol). Advantages and disadvantages of various options are compared, and the process of selecting a log-on authentication approach involving generation of a different password at…

Verification of rut depth collected with the INO laser rut measurement system (LRMS) : executive summary report.

DOT National Transportation Integrated Search

2011-11-01

Since 1985, ODOT has been manually collecting rut : depth data using a straight edge and dial gauge (S&G). This : method is slow and dangerous to pavement condition raters : when traffic control is not available. According to the : Pavement Condition...

Building a School District's Wide Area Network.

ERIC Educational Resources Information Center

Mastel, Vern L.

1996-01-01

Describes the development of a wide area network (WAN) in the Bismarck Public School District (North Dakota). Topics include design goals, network infrastructure, implementing library access, sharing resources across platforms, electronic mail, dial-in access, Internet access, adhering to software licenses, shareware and freeware, and monitoring…

Bioreactor Technology in Cardiovascular Tissue Engineering

NASA Astrophysics Data System (ADS)

Mertsching, H.; Hansmann, J.

Cardiovascular tissue engineering is a fast evolving field of biomedical science and technology to manufacture viable blood vessels, heart valves, myocar-dial substitutes and vascularised complex tissues. In consideration of the specific role of the haemodynamics of human circulation, bioreactors are a fundamental of this field. The development of perfusion bioreactor technology is a consequence of successes in extracorporeal circulation techniques, to provide an in vitro environment mimicking in vivo conditions. The bioreactor system should enable an automatic hydrodynamic regime control. Furthermore, the systematic studies regarding the cellular responses to various mechanical and biochemical cues guarantee the viability, bio-monitoring, testing, storage and transportation of the growing tissue.

Correlation of DIAL Ozone Observations with Lightning

NASA Technical Reports Server (NTRS)

Peterson, Harold; Kuang, Shi; Koshak, William; Newchurch, Michael

2013-01-01

The purpose of this project is to see whether ozone maxima measured by the DIfferential Absorption Lidar (DIAL) instrument in Huntsville, AL may be traced back to lightning events occurring 24- 48 hours beforehand. The methodology is to start with lidar measurements of ozone from DIAL as well as ozonesonde measurements. The HYbrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model is then used to determine the origin of these ozone maxima 24-48 hours prior. Data from the National Lightning Detection Network (NLDN) are used to examine the presence/absence of lightning along the trajectory. This type of analysis suggests that lightning-produced NOx may be responsible for some of the ozone maxima over Huntsville.

A report of work activities on the NASA Spacelink public electronic library

NASA Technical Reports Server (NTRS)

Smith, Willard A.

1994-01-01

NASA Spacelink is a comprehensive electronic data base of NASA and other source educational and informational materials. This service originates at Marshall Space Flight Center (MSFC) in Huntsville, Alabama. This is an education service of NASA Headquarters, through the MSFC Education Office, that first began in February of 1988. The new NASA Spacelink Public Electronic Library was the result of a study conducted to investigate an upgrade or redesign of the original NASA Spacelink. The UNIX Operating System was chosen to be the host operating system for the new NASA Spacelink Public Electronic Library. The UNIX system was selected for this project because of the strengths built into the embedded communication system and for its simple and direct file handling capabilities. The host hardware of the new system is a Sun Microsystems SPARCserver 1000 computer system. The configuration has four 50-MHz SuperSPARC processors with 128 megabytes of shared memory; three SB800 serial ports allowing 24 cable links for phone communications; 4.1 gigabytes of on-line disk storage; and ten (10) CD-ROM drives. Communications devices on the system are sufficient to support the expected number of users through the Internet, the local dial services, long distance dial services; the MSFC PABX, and the NPSS (NASA Packet Switching System) and 1-800 access service for the registered teachers.

76 FR 60765 - Mail or Telephone Order Merchandise Rule

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-30

... access, not telephone dial-up. \\19\\ U.S. Census Bureau, E-Stats, 2007 E-Commerce Multi-Sector Report, May... Shopping and Mail-Order Houses--Total and E-Commerce Sales by Merchandise Line: 2006-2007. Second, consumer... buyers access the Internet (e.g., dial-up telephone modem, cable, or wireless); (2) allow sellers to...

Characterization of a 16-Bit Digitizer for Lidar Data Acquisition

NASA Technical Reports Server (NTRS)

Williamson, Cynthia K.; DeYoung, Russell J.

2000-01-01

A 6-MHz 16-bit waveform digitizer was evaluated for use in atmospheric differential absorption lidar (DIAL) measurements of ozone. The digitizer noise characteristics were evaluated, and actual ozone DIAL atmospheric returns were digitized. This digitizer could replace computer-automated measurement and control (CAMAC)-based commercial digitizers and improve voltage accuracy.

46 CFR 525.3 - Availability of marine terminal operator schedules.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Availability of terminal schedules—(1) Availability to the Commission. A complete and current set of terminal... computer (PC) by: (1) Dial-up connection via public switched telephone networks (PSTN); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (c) Dial-up connection via PSTN. (1) This connection...

46 CFR 525.3 - Availability of marine terminal operator schedules.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Availability of terminal schedules—(1) Availability to the Commission. A complete and current set of terminal... computer (PC) by: (1) Dial-up connection via public switched telephone networks (PSTN); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (c) Dial-up connection via PSTN. (1) This connection...

FirstSearch and NetFirst--Web and Dial-up Access: Plus Ca Change, Plus C'est la Meme Chose?

ERIC Educational Resources Information Center

Koehler, Wallace; Mincey, Danielle

1996-01-01

Compares and evaluates the differences between OCLC's dial-up and World Wide Web FirstSearch access methods and their interfaces with the underlying databases. Also examines NetFirst, OCLC's new Internet catalog, the only Internet tracking database from a "traditional" database service. (Author/PEN)

Bandwidth Constraints to Using Video and Other Rich Media in Behavior Change Websites

PubMed Central

Jazdzewski, Stephen A; McKay, H Garth; Hudson, Clinton R

2005-01-01

Background Web-based behavior change interventions often include rich media (eg, video, audio, and large graphics). The rationale for using rich media includes the need to reach users who are not inclined or able to use text-based website content, encouragement of program engagement, and following the precedent set by news and sports websites. Objectives We describe the development of a bandwidth usage index, which seeks to provide a practical method to gauge the extent to which websites can successfully be used within different Internet access scenarios (eg, dial-up and broadband). Methods We conducted three studies to measure bandwidth consumption. In Study 1, we measured the bandwidth usage index for three video-rich websites (for smoking cessation, for caregivers, and for improving eldercare by family members). We then estimated the number of concurrent users that could be accommodated by each website under various Internet access scenarios. In Study 2, we sought to validate our estimated threshold number of concurrent users by testing the video-rich smoking cessation website with different numbers of concurrent users. In Study 3, we calculated the bandwidth usage index and threshold number of concurrent users for three versions of the smoking cessation website: the video-rich version (tested in Study 1), an audio-rich version, and a Web-enabled CD-ROM version in which all media-rich content was placed on a CD-ROM on the client computer. Results In Study 1, we found that the bandwidth usage index of the video-rich websites ranged from 144 Kbps to 93 Kbps. These results indicated that dial-up modem users would not achieve a “good user experience” with any of the three rich media websites. Results for Study 2 confirmed that usability was compromised when the estimated threshold number of concurrent users was exceeded. Results for Study 3 indicated that changing a website from video- to audio-rich content reduced the bandwidth requirement by almost 50%, but it remained too large to allow satisfactory use in dial-up modem scenarios. The Web-enabled CD-ROM reduced bandwidth requirements such that even a dial-up modem user could have a good user experience with the rich media content. Conclusions We conclude that the bandwidth usage index represents a practical tool that can help developers and researchers to measure the bandwidth requirements of their websites as well as to evaluate the feasibility of certain website designs in terms of specific use cases. These findings are discussed in terms of reaching different groups of users as well accommodating the intended number of concurrent users. We also discuss the promising option of using Web-enabled CD-ROMs to deliver rich media content to users with dial-up Internet access. We introduce a number of researchable themes for improving our ability to develop Web-based behavior change interventions that can better deliver what they promise. PMID:16236701

Bandwidth constraints to using video and other rich media in behavior change websites.

PubMed

Danaher, Brian G; Jazdzewski, Stephen A; McKay, H Garth; Hudson, Clinton R

2005-09-16

Web-based behavior change interventions often include rich media (eg, video, audio, and large graphics). The rationale for using rich media includes the need to reach users who are not inclined or able to use text-based website content, encouragement of program engagement, and following the precedent set by news and sports websites. We describe the development of a bandwidth usage index, which seeks to provide a practical method to gauge the extent to which websites can successfully be used within different Internet access scenarios (eg, dial-up and broadband). We conducted three studies to measure bandwidth consumption. In Study 1, we measured the bandwidth usage index for three video-rich websites (for smoking cessation, for caregivers, and for improving eldercare by family members). We then estimated the number of concurrent users that could be accommodated by each website under various Internet access scenarios. In Study 2, we sought to validate our estimated threshold number of concurrent users by testing the video-rich smoking cessation website with different numbers of concurrent users. In Study 3, we calculated the bandwidth usage index and threshold number of concurrent users for three versions of the smoking cessation website: the video-rich version (tested in Study 1), an audio-rich version, and a Web-enabled CD-ROM version in which all media-rich content was placed on a CD-ROM on the client computer. In Study 1, we found that the bandwidth usage index of the video-rich websites ranged from 144 Kbps to 93 Kbps. These results indicated that dial-up modem users would not achieve a "good user experience" with any of the three rich media websites. Results for Study 2 confirmed that usability was compromised when the estimated threshold number of concurrent users was exceeded. Results for Study 3 indicated that changing a website from video- to audio-rich content reduced the bandwidth requirement by almost 50%, but it remained too large to allow satisfactory use in dial-up modem scenarios. The Web-enabled CD-ROM reduced bandwidth requirements such that even a dial-up modem user could have a good user experience with the rich media content. We conclude that the bandwidth usage index represents a practical tool that can help developers and researchers to measure the bandwidth requirements of their websites as well as to evaluate the feasibility of certain website designs in terms of specific use cases. These findings are discussed in terms of reaching different groups of users as well accommodating the intended number of concurrent users. We also discuss the promising option of using Web-enabled CD-ROMs to deliver rich media content to users with dial-up Internet access. We introduce a number of researchable themes for improving our ability to develop Web-based behavior change interventions that can better deliver what they promise.

Accuracy and consistency of weights provided by home bathroom scales

PubMed Central

2013-01-01

Background Self-reported body weight is often used for calculation of Body Mass Index because it is easy to collect. Little is known about sources of error introduced by using bathroom scales to measure weight at home. The objective of this study was to evaluate the accuracy and consistency of digital versus dial-type bathroom scales commonly used for self-reported weight. Methods Participants brought functioning bathroom scales (n = 18 dial-type, n = 43 digital-type) to a central location. Trained researchers assessed accuracy and consistency using certified calibration weights at 10 kg, 25 kg, 50 kg, 75 kg, 100 kg, and 110 kg. Data also were collected on frequency of calibration, age and floor surface beneath the scale. Results All participants reported using their scale on hard surface flooring. Before calibration, all digital scales displayed 0, but dial scales displayed a mean absolute initial weight of 0.95 (1.9 SD) kg. Digital scales accurately weighed test loads whereas dial-type scale weights differed significantly (p < 0.05). Imprecision of dial scales was significantly greater than that of digital scales at all weights (p < 0.05). Accuracy and precision did not vary by scale age. Conclusions Digital home bathroom scales provide sufficiently accurate and consistent weights for public health research. Reminders to zero scales before each use may further improve accuracy of self-reported weight. PMID:24341761

Managing Innovation.

ERIC Educational Resources Information Center

Mason, Marilyn Gell

1991-01-01

Describes one library's use of technological innovation to provide Associated Press updates over the library's 24-hour dial-up service during the Persian Gulf War. Suggests five rules for innovation: (1) develop a shared vision; (2) foster frequent, formal, and informal communication; (3) empower employees; (4) take limited risks; and (5) use, but…

77 FR 74174 - National Oceanic and Atmospheric Administration (NOAA) National Climate Assessment and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-13

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration (NOAA) National Climate... NOAA National Climate Assessment and Development Advisory Committee (NCADAC). Time and Date: The..., DC 20006. The public will not be able to dial into the call. Please check the National Climate...

Infusion volume control and calculation using metronome and drop counter based intravenous infusion therapy helper.

PubMed

Park, Kyungnam; Lee, Jangyoung; Kim, Soo-Young; Kim, Jinwoo; Kim, Insoo; Choi, Seung Pill; Jeong, Sikyung; Hong, Sungyoup

2013-06-01

This study assessed the method of fluid infusion control using an IntraVenous Infusion Controller (IVIC). Four methods of infusion control (dial flow controller, IV set without correction, IV set with correction and IVIC correction) were used to measure the volume of each technique at two infusion rates. The infused fluid volume with a dial flow controller was significantly larger than other methods. The infused fluid volume was significantly smaller with an IV set without correction over time. Regarding the concordance correlation coefficient (CCC) of infused fluid volume in relation to a target volume, IVIC correction was shown to have the highest level of agreement. The flow rate measured in check mode showed a good agreement with the volume of collected fluid after passing through the IV system. Thus, an IVIC could assist in providing an accurate infusion control. © 2013 Wiley Publishing Asia Pty Ltd.

Water vapour intercomparison effort in the frame of HyMeX-SOP1

NASA Astrophysics Data System (ADS)

Summa, Donato; Di Girolamo, Paolo; Stelitano, Dario; Cacciani, Marco; Flamant, Cyrille; Chazette, Patrick; Ducrocq, Véronique; Nuret, Mathieu; Fourié, Nadia; Richard, Evelyne

2014-05-01

A water vapour intercomparison effort, involving airborne and ground-based water vapour lidar systems and mesoscale models, was carried out in the framework of the international HyMeX (Hydrological cycle in the Mediterranean Experiment) dedicated to the hydrological cycle and related high-impact events. Within HyMeX, a major field campaign was dedicated to heavy precipitation and flash flood events from 5 September to 6 November 2012. The 2 month field campaign took place over the Northwestern Mediterranean Sea and its surrounding coastal regions in France, Italy, and Spain. The main objective of this work is to provide accurate error estimates for the lidar systems i.e. the ground-based Raman lidar BASIL and the CNRS DIAL Leandre 2 on board the ATR42, as well as use BASIL data to validate mesoscale model results from the MESO NH and Arome WMED. The effort will benefit from the few dedicated ATR42 flights in the frame of the EUFAR Project "WaLiTemp". In the present work our attention was focused on two specific case studies: 13 September and 2 October in the altitude region 0.5 - 5.5 km. Comparisons between the ground-based Raman lidar BASIL and the airborne CNRS DIAL indicate a mean relative bias between the two sensors of 6.5%, while comparisons between BASIL and CNRS DIAL vs. the radiosondes indicate a bias of 2.6 and -3.5 %, respectively. The bias of BASIL vs. the ATR insitu sensor indicate a bias of -20.4 %. Specific attention will also be dedicated to the WALI/BASIL intercomparison effort which took place in Candillargues on 30 October 2012. Specific results from this intercomparison effort and from the intercomparison between BASIL and Meso-NH/AROME-WMed will be illustrated and discussed at the Conference.

46 CFR 520.9 - Access to tariffs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... networks (“PSTN”); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (b) Dial-up...) Internet connection. (1) This connection option requires that systems provide: (i) A universal resource locator (“URL”) Internet address (e.g., http://www.tariffsrus.com or http://1.2.3.4); and/or (ii) A URL...

46 CFR 520.9 - Access to tariffs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... networks (“PSTN”); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (b) Dial-up...) Internet connection. (1) This connection option requires that systems provide: (i) A universal resource locator (“URL”) Internet address (e.g., http://www.tariffsrus.com or http://1.2.3.4); and/or (ii) A URL...

46 CFR 520.9 - Access to tariffs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... networks (“PSTN”); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (b) Dial-up...) Internet connection. (1) This connection option requires that systems provide: (i) A universal resource locator (“URL”) Internet address (e.g., http://www.tariffsrus.com or http://1.2.3.4); and/or (ii) A URL...

46 CFR 520.9 - Access to tariffs.

Code of Federal Regulations, 2010 CFR

2010-10-01

... networks (“PSTN”); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (b) Dial-up...) Internet connection. (1) This connection option requires that systems provide: (i) A universal resource locator (“URL”) Internet address (e.g., http://www.tariffsrus.com or http://1.2.3.4); and/or (ii) A URL...

46 CFR 520.9 - Access to tariffs.

Code of Federal Regulations, 2011 CFR

2011-10-01

... networks (“PSTN”); or (2) The Internet (Web) by: (i) Web browser; or (ii) Telnet session. (b) Dial-up...) Internet connection. (1) This connection option requires that systems provide: (i) A universal resource locator (“URL”) Internet address (e.g., http://www.tariffsrus.com or http://1.2.3.4); and/or (ii) A URL...

Cellular Telephone Dialing Influences Kinematic and Spatiotemporal Gait Parameters in Healthy Adults.

PubMed

Seymour, Kelly M; Higginson, Christopher I; DeGoede, Kurt M; Bifano, Morgan K; Orr, Rachel; Higginson, Jill S

2016-01-01

Gait speed is typically reduced when individuals simultaneously perform other tasks. However, the impact of dual tasking on kinetic and kinematic gait parameters is unclear because these vary with gait speed. The objective of this study was to identify whether dual tasking impacts gait in healthy adults when speed is constant. Twenty-two healthy adults dialed a cell phone during treadmill walking at a self-selected speed while kinetic, kinematic, and spatial parameters were recorded. Results indicated that dual tasking did not impact phone dialing speed, but increased stride width, peak knee flexion during stance, and peak plantarflexion, and decreased knee and ankle range of motion. Dual tasking appears to influence kinematic gait variables in a manner consistent with promotion of stability.

Analysis of Requirements of On-Line Network Cataloging Services for Small, Academic, Public, School and Other Libraries: A Demonstration Project using the OCLC System. Final Report.

ERIC Educational Resources Information Center

Markuson, Barbara Evans

This report results from a project using the OCLC system to provide catalog services to small libraries. Alternatives described include: centralized cataloging, centralized book processing, sharing of OCLC terminals, and use of dial-up terminals. The OCLC data base was found useful for all types of small libraries. It is recommended that network…

Coherent laser radar at 2 microns using solid-state lasers

NASA Technical Reports Server (NTRS)

Henderson, Sammy W.; Suni, Paul J. M.; Hale, Charley P.; Hannon, Stephen M.; Magee, James R.; Bruns, Dale L.; Yuen, Eric H.

1993-01-01

Coherent laser radar systems using 2-micron Tm- and Tm, Ho-doped solid-state lasers are useful for the remote range-resolved measurement of atmospheric winds, aerosol backscatter, and DIAL measurements of atmospheric water vapor and CO2 concentrations. Recent measurements made with a 2-micron coherent laser radar system, advances in the laser technology, and atmospheric propagation effects on 2-micron coherent lidar performance are described.

Report on Development and Validation of Utilization Materials to Accompany Two Series of U.S. Office of Education Alcohol Education Films.

ERIC Educational Resources Information Center

Finn, Peter

This report records the development and validation by Abt Associates, Inc. of utilization materials developed to accompany the two U.S. Office of Education film series, Jackson Junior High and Dial A-L-C-O-H-O-L. The first section describes the process by which the nine project products were developed. These products include the following: (1) a…

Transportable Applications Environment (TAE) Plus: A NASA tool used to develop and manage graphical user interfaces

NASA Technical Reports Server (NTRS)

Szczur, Martha R.

1992-01-01

The Transportable Applications Environment (TAE) Plus was built to support the construction of graphical user interfaces (GUI's) for highly interactive applications, such as real-time processing systems and scientific analysis systems. It is a general purpose portable tool that includes a 'What You See Is What You Get' WorkBench that allows user interface designers to layout and manipulate windows and interaction objects. The WorkBench includes both user entry objects (e.g., radio buttons, menus) and data-driven objects (e.g., dials, gages, stripcharts), which dynamically change based on values of realtime data. Discussed here is what TAE Plus provides, how the implementation has utilized state-of-the-art technologies within graphic workstations, and how it has been used both within and without NASA.

Multitarget drug discovery projects in CNS diseases: quantitative systems pharmacology as a possible path forward.

PubMed

Geerts, Hugo; Kennis, Ludo

2014-01-01

Clinical development in brain diseases has one of the lowest success rates in the pharmaceutical industry, and many promising rationally designed single-target R&D projects fail in expensive Phase III trials. By contrast, successful older CNS drugs do have a rich pharmacology. This article will provide arguments suggesting that highly selective single-target drugs are not sufficiently powerful to restore complex neuronal circuit homeostasis. A rationally designed multitarget project can be derisked by dialing in an additional symptomatic treatment effect on top of a disease modification target. Alternatively, we expand upon a hypothetical workflow example using a humanized computer-based quantitative systems pharmacology platform. The hope is that incorporating rationally multipharmacology drug discovery could potentially lead to more impactful polypharmacy drugs.

76 FR 9782 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-22

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... policy framework for the development and adoption of a nationwide health information technology...

75 FR 3906 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-25

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... framework for the development and adoption of a nationwide health information technology infrastructure that...

75 FR 65485 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-25

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... the development and adoption of a nationwide health information technology infrastructure that permits...

75 FR 36658 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-28

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... policy framework for the development and adoption of a nationwide health information technology...

75 FR 51819 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... the development and adoption of a nationwide health information technology infrastructure that permits...

76 FR 4352 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-25

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... policy framework for the development and adoption of a nationwide health information technology...

75 FR 57026 - Office of the National Coordinator for Health Information Technology; HIT Policy Committee's...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-17

... Coordinator for Health Information Technology, HHS. ACTION: Notice of meetings. This notice announces... for Health Information Technology (ONC). The meetings will be open to the public via dial-in access... the development and adoption of a nationwide health information technology infrastructure that permits...

Translations on Telecommunications Policy, Research and Development. Number 4

DTIC Science & Technology

1977-06-14

will include an abbreviated dial service, where one, two or possibly three digits only need be dialled for commonly-used numbers. Push-button...in person at the post offices. [Text] [Havana JUVENTUD REBELDE in Spanish 14 Apr 77 p 2] 7717 CSO: 3010 26 INTER-ARAB AFFAIRS BRIEFS SUDANESE

A Composite View of Ozone Evolution in the 1995-1996 Northern Winter Polar Vortex Developed from Airborne Lidar and Satellite Observations

NASA Technical Reports Server (NTRS)

Douglass, A. R.; Schoeberl, M. R.; Kawa, S. R.; Browell, E. V.

2000-01-01

The processes which contribute to the ozone evolution in the high latitude northern lower stratosphere are evaluated using a three dimensional model simulation and ozone observations. The model uses winds and temperatures from the Goddard Earth Observing System Data Assimilation System. The simulation results are compared with ozone observations from three platforms: the differential absorption lidar (DIAL) which was flown on the NASA DC-8 as part of the Vortex Ozone Transport Experiment; the Microwave Limb Sounder (MLS); the Polar Ozone and Aerosol Measurement (POAM II) solar occultation instrument. Time series for the different data sets are consistent with each other, and diverge from model time series during December and January. The model ozone in December and January is shown to be much less sensitive to the model photochemistry than to the model vertical transport, which depends on the model vertical motion as well as the model vertical gradient. We evaluate the dependence of model ozone evolution on the model ozone gradient by comparing simulations with different initial conditions for ozone. The modeled ozone throughout December and January most closely resembles observed ozone when the vertical profiles between 12 and 20 km within the polar vortex closely match December DIAL observations. We make a quantitative estimate of the uncertainty in the vertical advection using diabatic trajectory calculations. The net transport uncertainty is significant, and should be accounted for when comparing observations with model ozone. The observed and modeled ozone time series during December and January are consistent when these transport uncertainties are taken into account.

A Composite View of Ozone Evolution in the 1995-96 Northern Winter Polar Vortex Developed from Airborne Lidar and Satellite Observations

NASA Technical Reports Server (NTRS)

Douglass, Anne R.; Schoeberl, M. R.; Kawa, S. R.

2000-01-01

The processes which contribute to the ozone evolution in the high latitude lower stratosphere are evaluated using a three dimensional model simulation and ozone observations. The model uses winds and temperatures from the Goddard Earth Observing System Data Assimilation System. The simulation results are compared with ozone observations from three platforms: the differential absorption lidar (DIAL) which was flown on the NASA DC-8 as part of the Vortex Ozone Transport Experiment; the Microwave Limb Sounder (MLS) on the Upper Atmosphere Research Satellite; and the Polar Ozone and Aerosol Measurement (POAM II) solar occulation instrument, on board the French Satellite Pour I'Observations de la Terre. Comparisons of the different data sets with the model simulation are shown to provide complementary information and a consistent view of the ozone evolution. The model ozone in December and January is shown to be sensitive to the ozone vertical gradient and the model vertical transport, and only weakly sensitive to the model photochemistry. The most consistent comparison between observed and modeled ozone evolution is found for a simulation where the vertical profiles between 12 and 20 km within the polar vortex closely match December DIAL observations. Diabatic trajectory calculations are used to estimate the uncertainty due to vertical advection quantitatively. The transport uncertainty is significant, and should be accounted for when comparing observations with model ozone. The model ozone evolution during December and January is broadly consistent with the observations when these transport uncertainties are taken into account.

A Compact Ti:Sapphire Laser With its Third Harmonic Generation (THG) for an Airborne Ozone Differential Absorption Lidar (DIAL) Transmitter

NASA Technical Reports Server (NTRS)

Chen, Songsheng; Storm, Mark E.; Marsh, Waverly D.; Petway, Larry B.; Edwards, William C.; Barnes, James C.

2000-01-01

A compact and high-pulse-energy Ti:Sapphire laser with its Third Harmonic Generation (THG) has been developed for an airborne ozone differential absorption lidar (DIAL) to study the distributions and concentrations of the ozone throughout the troposphere. The Ti:Sapphire laser, pumped by a frequency-doubled Nd:YAG laser and seeded by a single mode diode laser, is operated either at 867 nm or at 900 nm with a pulse repetition frequency of 20 Hz. High energy laser pulses (more than 110 mJ/pulse) at 867 nm or 900 nm with a desired beam quality have been achieved and utilized to generate its third harmonic at 289nm or 300nm, which are on-line and off-line wavelengths of an airborne ozone DIAL. After being experimentally compared with Beta-Barium Borate (beta - BaB2O4 or BBO) nonlinear crystals, two Lithium Triborate (LBO) crystals (5 x 5 x 20 cu mm) are selected for the Third Harmonic Generation (THG). In this paper, we report the Ti:Sapphire laser at 900 nm and its third harmonic at 300 nm. The desired high ultraviolet (UV) output pulse energy is more than 30 mJ at 300 nm and the energy conversion efficiency from 900 nm to 300 nm is 30%.

Lidars as an operational tool for meteorology and advanced atmospheric research

NASA Astrophysics Data System (ADS)

Simeonov, Valentin; Dinoev, Todor; Serikov, Ilya; Froidevaux, Martin; Bartlome, Marcel; Calpini, Bertrand; Bobrovnikov, Sergei; Ristori, Pablo; van den Bergh, Hubert; Parlange, Marc; Archinov, Yury

2010-05-01

The talk will present the concept and observation results of three advanced lidar systems developed recently at the Swiss federal Institute of Technology- Lausanne (EPFL) Switzerland. Two of the systems are Raman lidars for simultaneous water vapor, temperature and aerosol observations and the third one is an ozone UV DIAL system. The Ranan lidars use vibrational water vapor and nitrogen signals to derive water vapor mixing ratio and temperature, aerosol extinction and backscatter are measured using pure-rotational Raman and elastic signals. The first Raman lidar (RALMO) is a fully automated, water vapor /temperature/aerosol lidar developed for operational use by the Swiss meteorological office (MeteoSiss). The lidar supplies water vapor mixing ratio and temperature plus aerosol extinction and backscatter coefficients at 355 nm. The operational range of the lidar is 100-7000 m (night time) and 100- 5000 m (daytime) with time resolution of 30 min. The spatial resolution varies with height from 25 to 300 m in order to maintain the maximum measurement error of 10%. The system is designed to provide long-term database with minimal instrument-induced variations in time of the measured parameters. The lidar has been in regular operation in the main aerological station of Meteoswiss- Payerne since September 2008. The second Raman lidar is a new generation, solar-blind system with an operational range 10-500 m and high spatial (1.5 m) and temporal (1 s) resolutions designed for simultaneous humidity, temperature, and aerosol measurements in the lower atmosphere. To maintain the measurement accuracy while operating with fixed spatial and temporal resolution, the receiver is designed to provide lower than ten dynamic range of the signals within the distance range of the lidar. The lidar has 360° azimuth and 240°elevation scanning ability. The lidar was used in two field campaigns aiming to study the structure of the lower atmosphere over complex terrains and, in particular, to advance our understanding of turbulent blending mechanisms in the unstable atmosphere. The third lidar is an ozone UV DIAL system designed for studies of the upper troposphere, lower stratosphere ozone exchange processes. The lidar is based on a commercial fourth harmonic Nd:YAG laser. The DIAL wavelengths (284 and 304 nm) are produced by stimulated Raman conversion in high pressure nitrogen. A 76 cm in diameter Cassegrein telescope is used in the receiver and the spectral separation of the signals is carried out by an imaging-grating based polychromator. The operational distance of the lidar is 6000 -12000 m ASL with a statistical error lower than 10%. The lidar is deployed at the High Altitude Research Station Jungfraujoch at 3600 m altitude in the Swiss Alps. The lidar accuracy was verified by comparison to profiles taken by ECC balloon-borne sondes launched by Meteoswiss from Payerne. The lidar has been in use from September 2008 and since that time several stratospheric intrusions and cases of intercontinental transport and transport from the atmospheric boundary layer have been observed.

Western blot analysis of sera from dogs with suspected food allergy.

PubMed

Favrot, Claude; Linek, Monika; Fontaine, Jacques; Beco, Luc; Rostaher, Ana; Fischer, Nina; Couturier, Nicolas; Jacquenet, Sandrine; Bihain, Bernard E

2017-04-01

Food allergy is often suspected in dogs with clinical signs of atopic dermatitis. This diagnosis is confirmed with an elimination diet and a subsequent challenge with regular food. Laboratory tests for the diagnosis of food allergy in dogs are unreliable and/or technically difficult. Cyno-DIAL ® is a Western blot method that might assist with the selection of an appropriate elimination diet. To evaluate the performance of Cyno-DIAL ® for the selection of an elimination diet and diagnosis of food allergy. Thirty eight dogs with atopic dermatitis completed an elimination diet. Combining the results of the diet trials and the challenges, 14 dogs were classified as food allergic (FA), 22 as nonfood-allergic and two as ambiguous cases. Amongst all dogs and amongst dogs with a clinical diagnosis of FA, 3% and 7% (respectively) were positive to Royal Canin Anallergenic ® , Vet-Concept Kanguru ® or Vet-Concept Dog Sana ® ; 8% and 7% to Hill's d/d Duck and Rice ® ; 8% and 21% to Hill's z/d Ultra Allergen Free ® ; 53% and 64% to Eukanuba Dermatosis FP ® ; and 32% and 43% to a home-cooked diet of horse meat, potatoes and zucchini. The specificity and sensitivity of Cyno-DIAL ® for diagnosing food allergy were 73% and 71%, respectively. Although Cyno-DIAL ® was considered potentially useful for identifying appropriate foods for elimination diet trials, it cannot be recommended for the diagnosis of food allergy. The Cyno-DIAL ® test performed better than some previously evaluated ELISA-based tests. © 2017 ESVD and ACVD.

"Dial-R,""Motor-Free Visual Perception Test", and "Peabody Picture Vocabulary Test": Interpretation from a Kindergarten Screening.

ERIC Educational Resources Information Center

Carmichael, Karla Delle

The Developmental Indicators for the Assessment of Learning-Revised (Dial-R) Test, the Peabody Picture Vocabulary Test (PPVT), and the Motor-Free Visual Perception Test (MFVPT) were used for kindergarten screening in three rural schools in Texas. Teachers in the schools requested a handbook that would help them interpret test scores and plan…

Dialing in single-site reactivity of a supported calixarene-protected tetrairidium cluster catalyst

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palermo, Andrew; Solovyov, Andrew; Ertler, Daniel

2017-05-04

A closed Ir 4carbonyl cluster,1, comprising a tetrahedral metal frame and threetert-butyl-calix[4]arene(OPr) 3(OCH 2PPh 2) (Ph = phenyl; Pr = propyl) ligands at the basal plane, was silica supported and consists of “*” and “S” sites, which could be dialed in selectively for controlling ethylene hydrogenation catalysis.

The accuracy of mean-growth estimates made with dial-gage dendrometers

Treesearch

Barton M. Blum; Dale S. Solomon

1966-01-01

In recent years a great deal of interest has been focused on tree growth as measured with relatively precise instruments over short periods of time. These growth measurements are usually made with vernier-band dendrometers similar to those described by Hall (1944) and Liming (1957), or dial-gage dendrometers similar to those described by Reineke (1932) and Daubenmire (...

Component-Based Visualization System

NASA Technical Reports Server (NTRS)

Delgado, Francisco

2005-01-01

A software system has been developed that gives engineers and operations personnel with no "formal" programming expertise, but who are familiar with the Microsoft Windows operating system, the ability to create visualization displays to monitor the health and performance of aircraft/spacecraft. This software system is currently supporting the X38 V201 spacecraft component/system testing and is intended to give users the ability to create, test, deploy, and certify their subsystem displays in a fraction of the time that it would take to do so using previous software and programming methods. Within the visualization system there are three major components: the developer, the deployer, and the widget set. The developer is a blank canvas with widget menu items that give users the ability to easily create displays. The deployer is an application that allows for the deployment of the displays created using the developer application. The deployer has additional functionality that the developer does not have, such as printing of displays, screen captures to files, windowing of displays, and also serves as the interface into the documentation archive and help system. The third major component is the widget set. The widgets are the visual representation of the items that will make up the display (i.e., meters, dials, buttons, numerical indicators, string indicators, and the like). This software was developed using Visual C++ and uses COTS (commercial off-the-shelf) software where possible.

Novel self-powered pH indicator using ionic polymeric gel muscles

NASA Astrophysics Data System (ADS)

Shahinpoor, Mohsen

1994-05-01

A novel design for a torsional spring-loaded pH indicator using ionic polymeric gel fibrous muscles is presented. The essential parts of the proposed self-powered pH indicator are a pair of co-axial and concentric cylinders, an assembly of fibrous polyacrylonitrile (PAN) muscles, a torsional spring, and a dial indicator. The two co-axial cylinders are such that the inner cylinder may pivotally rotate about the central rotation axis that is fixed to the inner bottom or side of the outer cylinder. The outer cylinder also serves as a reservoir for any liquid whose pH is to be determined either statically or dynamically. The internal cylindrical drum is further equipped with a dial indicator on one of its outer end caps such that when a pH environment is present the contraction or expansion of the PAN fibers cause the inner drum to rotate and thus give a reading of the dial indicator. The motion of the dial indicator may also be converted to an electrical signal (voltage) for digital electronics display and computer control. A mathematical model is also presented for the dynamic response of the self-powered pH indicator made with contractile PAN fiber bundle assemblies.

Practical Design Guidelines for Fugitive Gas Detection from Unmanned Aerial Vehicles

NASA Astrophysics Data System (ADS)

Tandy, William D., Jr.

Simulation, design, and analysis are combined in this effort to realize a UAV-scale instrument for fugitive gas detection. The contributing material to the industry begins by extending and correlating an integrated Gaussian plume model useful for instrument predictions and trade studies, regardless of the instrument type or molecule of interest. A variety of generally applicable plots are produced from this foundation, including receiver operator curves for leak rate detectability vs. wind speed, beam diameter vs. leak rate detectability, and plots for required scan densities. The atmospheric and instrument parameter trade studies are followed by hardware-specific analyses applicable to differential absorption lidar (DIAL) instruments. A synopsis of the lessons learned from hands-on experiences in the lab further define the design space for DIAL sensors. The dissertation culminates in the detailed design and analysis of two DIAL instrument concepts. The conclusion is that a DIAL instrument capable of reliably detecting a 50 SCFH plume in winds speeds up to 7 mph is on the threshold of being achievable on a quadcopter platform. Of special note is that the effort was funded by a Pipeline and Hazardous Materials Safety Administration grant and performed in collaboration with Ball Aerospace & Technologies.

Design and development aspects of flexure mechanism for high precision application

NASA Astrophysics Data System (ADS)

Sollapur, Shrishail B.; Patil, M. S.; Deshmukh, S. P.

2018-04-01

Planer XY Flexurel Mechanisms has various applications in precision motion mechanisms. A flexural mechanism generates relative motion between fixed support and motion stage using flexibility of material. This mechanism offers zero backlash, frictionless motion and high order repeatability. It is relatively compact in design as compared to rigid link mechanism. The merits of using flexure is complete mechanism can be from single monolith. Modelling of flexural mechanism to provide accurate scanning of comparatively larger range at a higher speed. Static Analysis of mechanism is carried out on FEA tool to determine static deflection of motion stage. Further Mechanism is actuated with the help of weight pan and weights. The resultant displacement is measured on Dial Gauge Indicator. Experimental set-up consists of Flexural mechanism, Dial Gauge, Weight Pan and Weights, Pulley, String, Small metal strip, Optical Bread Board etc. Further experimental Results and Analytical Results are compared and minimum deviation is found.

Unveiling the mode of action of antibacterial labdane diterpenes from Alpinia nigra (Gaertn.) B. L. Burtt seeds.

PubMed

Ghosh, Sudipta; Indukuri, Kiran; Bondalapati, Somasekhar; Saikia, Anil K; Rangan, Latha

2013-08-01

The labdane diterpene, (E)-labda-8(17), 12-diene-15, 16-dial (compound A) and its epoxide analogue, (E)-8β, 17-Epoxylabd-12-ene-15, 16-dial (compound B) were isolated from the seeds of Alpinia nigra for the first time. The antibacterial activities of both compounds were evaluated against three Gram-positive and four Gram-negative bacteria, and flow cytometric analysis revealed that these compounds caused significant damage to the bacterial cell membranes. Further, field emission scanning electron microscope imaging and cell leakage analysis confirmed that the labdane diterpenes were responsible for bacterial cell membrane damage and disintegration. Our findings provide new insight into the broad-spectrum effects of two natural labdane diterpenes that may be useful in the future development of herbal antibiotic products. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

Airborne Lidar measurements of aerosols, mixed layer heights, and ozone during the 1980 PEPE/NEROS summer field experiment

NASA Technical Reports Server (NTRS)

Browell, E. V.; Shipley, S. T.; Butler, C. F.; Ismail, S.

1985-01-01

A detailed summary of the NASA Ultraviolet Differential Absorption Lidar (UV DIAL) data archive obtained during the EPA Persistent Elevated Pollution Episode/Northeast Regional Oxidant Study (PEPE/NEROS) Summer Field Experiment Program (July through August 1980) is presented. The UV dial data set consists of remote measurements of mixed layer heights, aerosol backscatter cross sections, and sequential ozone profiles taken during 14 long-range flights onboard the NASA Wallops Flight Center Electra aircraft. These data are presented in graphic and tabular form, and they have been submitted to the PEPE/NEROS data archive on digital magnetic tape. The derivation of mixing heights and ozone profiles from UV Dial signals is discussed, and detailed intercomparisons with measurements obtained by in situ sensors are presented.

Improvement of web-based data acquisition and management system for GOSAT validation lidar data analysis

NASA Astrophysics Data System (ADS)

Okumura, Hiroshi; Takubo, Shoichiro; Kawasaki, Takeru; Abdullah, Indra Nugraha; Uchino, Osamu; Morino, Isamu; Yokota, Tatsuya; Nagai, Tomohiro; Sakai, Tetsu; Maki, Takashi; Arai, Kohei

2013-01-01

A web-base data acquisition and management system for GOSAT (Greenhouse gases Observation SATellite) validation lidar data-analysis has been developed. The system consists of data acquisition sub-system (DAS) and data management sub-system (DMS). DAS written in Perl language acquires AMeDAS (Automated Meteorological Data Acquisition System) ground-level local meteorological data, GPS Radiosonde upper-air meteorological data, ground-level oxidant data, skyradiometer data, skyview camera images, meteorological satellite IR image data and GOSAT validation lidar data. DMS written in PHP language demonstrates satellite-pass date and all acquired data. In this article, we briefly describe some improvement for higher performance and higher data usability. GPS Radiosonde upper-air meteorological data and U.S. standard atmospheric model in DAS automatically calculate molecule number density profiles. Predicted ozone density prole images above Saga city are also calculated by using Meteorological Research Institute (MRI) chemistry-climate model version 2 for comparison to actual ozone DIAL data.

Practical Approach To Building A Mid-Wave Remote Sensing System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pyke, Benjamin J.

The purpose of this project, Laser Active Transmitter & Receiver (LATR), was to build a mobile ground based remote sensing system that can detect, identify and quantify a specific gaseous species using Differential Absorption LIDAR (DIAL). This thesis project is concerned with the development and field testing of a mid-wave infrared active remote sensing system, capable of identifying and quantifying emissions in the 3.2 – 3.5 micron range. The goal is to give a brief description of what remote sensing is about and the specific technique used to analyze the collected data. The thesis will discuss the transmitter and themore » associated subsystems used to create the required wavelength, and the receiver used to collect the returns. And finally, the thesis will discuss the process of collecting the data and some of the results from field and lab collections.« less

Evolution of the intelligent telecommunications network

NASA Astrophysics Data System (ADS)

Mayo, J. S.

1982-02-01

The development of the U.S. telecommunications network is described and traced from the invention of the telephone by Bell in 1876 to the use of integrated circuits and the UNIX system for interactive computers. The dialing system was introduced in the 19th century, and amplifiers were invented to permit coast to coast communication by 1914. Hierarchical switching was installed in the 1930s, along with telephoto and teletype services. PCM was invented in the 1930s, but was limited to military applications until the transistorized computer was fabricated in 1958, which coincided with spaceflight and the Telstar satellite in 1962. Fiber optics systems with laser pulse transmission are now entering widespread application, following the 1976 introduction of superfast digital switches controlled by a computer and capable of handling 1/2 million calls per hour. Projected advances are in increased teleconferencing, electronic mail, and full computer terminal services.

From Dog Sled to Dial Phone: A Cultural Gap? -- The Far North.

ERIC Educational Resources Information Center

Dicks, Dennis

1977-01-01

Examines socioeconomic events surrounding major improvements in telephone service in the Eastern Canadian Arctic. Focuses on five towns at different stages of telecommunications development and relates the increased technology to air travel, use of the mail, changes in fur sales, changes in crime levels, and restructuring of communications…

Creating an Information Literate School: Information Literacy in Action.

ERIC Educational Resources Information Center

Batz, Linda; Rosenberg, Harlene

1999-01-01

Describes an award-winning instructional media center (IMC) at a New Jersey high school. The IMC (library) is the school's hub from 7:15 a.m. to 6 p.m., and has dial-in access. This information-literacy program emphasizes total-quality-management principles, ongoing professional development, teacher support, and information skills instruction.…

A Ground-Based Profiling Differential Absorption LIDAR System for Measuring CO2 in the Planetary Boundary Layer

NASA Technical Reports Server (NTRS)

Andrews, Arlyn E.; Burris, John F.; Abshire, James B.; Krainak, Michael A.; Riris, Haris; Sun, Xiao-Li; Collatz, G. James

2002-01-01

Ground-based LIDAR observations can potentially provide continuous profiles of CO2 through the planetary boundary layer and into the free troposphere. We will present initial atmospheric measurements from a prototype system that is based on components developed by the telecommunications industry. Preliminary measurements and instrument performance calculations indicate that an optimized differential absorption LIDAR (DIAL) system will be capable of providing continuous hourly averaged profiles with 250m vertical resolution and better than 1 ppm precision at 1 km. Precision increases (decreases) at lower (higher) altitudes and is directly proportional to altitude resolution and acquisition time. Thus, precision can be improved if temporal or vertical resolution is sacrificed. Our approach measures absorption by CO2 of pulsed laser light at 1.6 microns backscattered from atmospheric aerosols. Aerosol concentrations in the planetary boundary layer are relatively high and are expected to provide adequate signal returns for the desired resolution. The long-term goal of the project is to develop a rugged, autonomous system using only commercially available components that can be replicated inexpensively for deployment in a monitoring network.

Lidar Measurements of Aerosol and Ozone Distributions During the 1992 Airborne Arctic Stratospheric Expedition

NASA Technical Reports Server (NTRS)

Browell, E. V.; Butler, C. F.; Fenn, M. A.; Grant, W. B.; Carter, A. F.

1992-01-01

The LaRC airborne lidar system was operated from the ARC DC-8 aircraft during the 1992 Airborne Arctic Stratospheric Expedition (ASEE-2) to investigate the distribution of stratospheric aerosols and O3 across the Arctic vortex from Jan. to Mar. 1992. Monthly flights were made across the Arctic vortex from Anchorage, Alaska, to Stavanger, Norway, and then back to Bangor, Maine, and additional round-trip flights north into the vortex were made each month from either Stavanger or Bangor depending on the location of the vortex that month. The airborne lidar system uses the differential absorption lidar (DIAL) technique at laser wavelengths of 301.5 and 310.8 nm to measure O3 profiles above the DC-8 over the 12-25 km altitude range. Lidar measurements of aerosol backscatter and depolarization profiles over the 12-30 km altitude range are made simultaneously with the O3 measurements using infrared (IR) and visible (VIS) laser wavelengths of 603 and 1064 nm, respectively. The measurements of Pinatubo aerosols, polar stratospheric clouds, and O3 made with the airborne DIAL system during the AASE-2 expedition and to chemical and dynamical process that contribute to O3 depletion in the wintertime Arctic stratosphere.

Design of Laser Based Monitoring Systems for Compliance Management of Odorous and Hazardous Air Pollutants in Selected Chemical Industrial Estates at Hyderabad, India

NASA Astrophysics Data System (ADS)

Sudhakar, P.; Kalavathi, P.; Ramakrishna Rao, D.; Satyanarayna, M.

2014-12-01

Industrialization can no longer sustain without internalization of the concerns of the receiving environment and land-use. Increased awareness and public pressure, coupled with regulatory instruments and bodies exert constant pressure on industries to control their emissions to a level acceptable to the receiving environment. However, when a group of industries come-up together as an industrial estate, the cumulative impacts of all the industries together often challenges the expected/desired quality of receiving environment, requiring stringent pollution control and monitoring measures. Laser remote sensing techniques provide powerful tools for environmental monitoring. These methods provide range resolved measurements of concentrations of various gaseous pollutants and suspended particulate matter (SPM) not only in the path of the beam but over the entire area. A three dimensional mapping of the pollutants and their dispersal can be estimated using the laser remote sensing methods on a continuous basis. Laser Radar (Lidar) systems are the measurements technology used in the laser remote sensing methods. Differential absorption lidar (DIAL) and Raman Lidar technologies have proved to be very useful for remote sensing of air pollutants. DIAL and Raman lidar systems can be applied for range resolved measurements of molecules like SO2, NO2, O3 Hg, CO, C2H4, H2O, CH4, hydrocarbons etc. in real time on a continuous basis. This paper describes the design details of the DAIL and Raman lidar techniques for measurement of various hazardous air pollutants which are being released into the atmosphere by the chemical industries operating in the Bachupally industrial Estate area at Hyderabad, India. The relative merits of the two techniques have been studied and the minimum concentration of pollutants that can be measured using these systems are presented. A dispersion model of the air pollutants in the selected chemical industrial estates at Hyderabad has been developed.

A Guide Management System Based on RFID and Bluetooth Technology

NASA Astrophysics Data System (ADS)

Li, Han-Sheng; Wang, Jun-Jun

The most fundamental and important requirement of the tour guide in the tour process is to ensure the safety of tourists. In this paper, a portable guide management system is designed based on RFID technology, the Android software and blue-tooth communication technology. Through this system, the guide can get real-time information if some tourists are l behind, and send text message or dial to those tourists who are l behind immediately. The system reduces the roll-calling time on the tourists, improves the tour guide work efficiency and service quality.

Informatics application provides instant research to practice benefits.

PubMed Central

Bowles, K. H.; Peng, T.; Qian, R.; Naylor, M. D.

2001-01-01

A web-based research information system was designed to enable our research team to efficiently measure health related quality of life among frail older adults in a variety of health care settings (home care, nursing homes, assisted living, PACE). The structure, process, and outcome data is collected using laptop computers and downloaded to a SQL database. Unique features of this project are the ability to transfer research to practice by instantly sharing individual and aggregate results with the clinicians caring for these elders and directly impacting the quality of their care. Clinicians can also dial in to the database to access standard queries or receive customized reports about the patients in their facilities. This paper will describe the development and implementation of the information system. The conference presentation will include a demonstration and examples of research to practice benefits. PMID:11825156

Distracted Driving and Risk of Road Crashes among Novice and Experienced Drivers

PubMed Central

Klauer, Sheila G.; Guo, Feng; Simons-Morton, Bruce G.; Ouimet, Marie Claude; Lee, Suzanne E.; Dingus, Thomas A.

2014-01-01

BACKGROUND Distracted driving attributable to the performance of secondary tasks is a major cause of motor vehicle crashes both among teenagers who are novice drivers and among adults who are experienced drivers. METHODS We conducted two studies on the relationship between the performance of secondary tasks, including cell-phone use, and the risk of crashes and near-crashes. To facilitate objective assessment, accelerometers, cameras, global positioning systems, and other sensors were installed in the vehicles of 42 newly licensed drivers (16.3 to 17.0 years of age) and 109 adults with more driving experience. RESULTS During the study periods, 167 crashes and near-crashes among novice drivers and 518 crashes and near-crashes among experienced drivers were identified. The risk of a crash or near-crash among novice drivers increased significantly if they were dialing a cell phone (odds ratio, 8.32; 95% confidence interval [CI], 2.83 to 24.42), reaching for a cell phone (odds ratio, 7.05; 95% CI, 2.64 to 18.83), sending or receiving text messages (odds ratio, 3.87; 95% CI, 1.62 to 9.25), reaching for an object other than a cell phone (odds ratio, 8.00; 95% CI, 3.67 to 17.50), looking at a roadside object (odds ratio, 3.90; 95% CI, 1.72 to 8.81), or eating (odds ratio, 2.99; 95% CI, 1.30 to 6.91). Among experienced drivers, dialing a cell phone was associated with a significantly increased risk of a crash or near-crash (odds ratio, 2.49; 95% CI, 1.38 to 4.54); the risk associated with texting or accessing the Internet was not assessed in this population. The prevalence of high-risk attention to secondary tasks increased over time among novice drivers but not among experienced drivers. CONCLUSIONS The risk of a crash or near-crash among novice drivers increased with the performance of many secondary tasks, including texting and dialing cell phones. (Funded by the Eunice Kennedy Shriver National Institute of Child Health and Human Development and the National Highway Traffic Safety Administration.) PMID:24382065

1.6 μm DIAL Measurement and Back Trajectory Analysis of CO2 Concentration Profiles in the Lower-Atmosphere

NASA Astrophysics Data System (ADS)

Shibata, Y.; Nagasawa, C.; Abo, M.

2016-12-01

Carbon dioxide (CO2) is the primary greenhouse gas emitted through human activities. In addition to the ground level CO2 network, vertical CO2 concentration profiles also play an important role for the estimation of the carbon budget and global warming in the inversion method. Especially, for the detailed analysis of forest carbon dynamics and CO2 fluxes of urban area, vertical CO2 concentration profiles with high spatial and temporal resolution in the lower atmosphere have been conducted by a differential absorption lidar (DIAL). We have observed several vertical profiles of CO2 concentrations for nighttime and daytime from 0.25 to 2.5 km altitude with range resolution of 300 m and integration time of 1 hour. In order to extract information on the origin of the CO2 masses, one day back trajectories were calculated by using a three dimensional (3-D) atmospheric transport model. In many cases, CO2 low concentration layers of over 1.5km altitude were flown by westerly winds from the forest. In another case, high concentration layers of CO2 were flown from the urban areas. As the spectra of absorption lines of any molecules are influenced basically by the temperature in the atmosphere, laser beams of three wavelengths around a CO2 absorption spectrum are transmitted alternately to the atmosphere for simultaneous measurements of CO2 concentration and temperature profiles. Moreover, a few processing algorithms of CO2-DIAL are also performed for improvement of measurement accuracy. For computation of trajectories and drawing their figures, the JRA-25 data provided by the cooperative research project for the JRA-25 long-term reanalysis of the Japan Meteorological Agency (JMA) and the Central Research Institute of Electric Power Industry (CRIEPI) and the NIPR trajectory model (Tomikawa and Sato, 2005; http://firp-nitram.nipr.ac.jp) were used. This work was financially supported by the System Development Program for Advanced Measurement and Analysis of the Japan Science and Technology Agency.

Distracted driving and risk of road crashes among novice and experienced drivers.

PubMed

Klauer, Sheila G; Guo, Feng; Simons-Morton, Bruce G; Ouimet, Marie Claude; Lee, Suzanne E; Dingus, Thomas A

2014-01-02

Distracted driving attributable to the performance of secondary tasks is a major cause of motor vehicle crashes both among teenagers who are novice drivers and among adults who are experienced drivers. We conducted two studies on the relationship between the performance of secondary tasks, including cell-phone use, and the risk of crashes and near-crashes. To facilitate objective assessment, accelerometers, cameras, global positioning systems, and other sensors were installed in the vehicles of 42 newly licensed drivers (16.3 to 17.0 years of age) and 109 adults with more driving experience. During the study periods, 167 crashes and near-crashes among novice drivers and 518 crashes and near-crashes among experienced drivers were identified. The risk of a crash or near-crash among novice drivers increased significantly if they were dialing a cell phone (odds ratio, 8.32; 95% confidence interval [CI], 2.83 to 24.42), reaching for a cell phone (odds ratio, 7.05; 95% CI, 2.64 to 18.83), sending or receiving text messages (odds ratio, 3.87; 95% CI, 1.62 to 9.25), reaching for an object other than a cell phone (odds ratio, 8.00; 95% CI, 3.67 to 17.50), looking at a roadside object (odds ratio, 3.90; 95% CI, 1.72 to 8.81), or eating (odds ratio, 2.99; 95% CI, 1.30 to 6.91). Among experienced drivers, dialing a cell phone was associated with a significantly increased risk of a crash or near-crash (odds ratio, 2.49; 95% CI, 1.38 to 4.54); the risk associated with texting or accessing the Internet was not assessed in this population. The prevalence of high-risk attention to secondary tasks increased over time among novice drivers but not among experienced drivers. The risk of a crash or near-crash among novice drivers increased with the performance of many secondary tasks, including texting and dialing cell phones. (Funded by the Eunice Kennedy Shriver National Institute of Child Health and Human Development and the National Highway Traffic Safety Administration.).

Initial development of a device for controlling manually applied forces.

PubMed

Waddington, Gordon S; Adams, Roger D

2007-05-01

In both simulation and manual therapy studies, substantial variability has been shown when therapists attempt to replicate an applied force. Knowledge about the forces employed during treatment could reduce this variability. In the current project, a prototype for a mobilizing device incorporating a dynamometer was constructed. The prototype device was built around a conventional "hand-grip" dynamometer to give dial visibility during application of mobilizing forces and a moulded handle was used to increase the hand contact surface during force application. The variability of the mobilization forces produced was measured, and ratings of comfort during a simulated spinal mobilization technique were obtained from therapists. Thirty physiotherapists were randomly allocated to apply either: (i) their own estimate of a grade III mobilization force using their hands in a pisiform grip or (ii) a 100N force with the manual therapy dynamometer, and to rate comfort during the performance of both techniques on a 100mm visual analogue scale. Variance in dynamometer-dial-guided force application was always significantly less than the variance in therapist-concept-guided force application. Repeated-measures tests showed that the mean force produced at grade III was not significantly different from 100N, but physiotherapist comfort ratings were found to be significantly greater (P<0.01) when the manual therapy dynamometer was used. Manually applied force variability was significantly less and therapist comfort greater when using a device with visual access to a dial giving immediate force readout.

Support of validation of SAGE 2 data

NASA Technical Reports Server (NTRS)

Copeland, Gary E.

1986-01-01

An error analysis of differential absorption lidar (DIAL) measurements of stratospheric ozone from a Space Shuttle is discussed. A transmitter system consisting of a KrF excimer laser pumping gas cells of H2 or D2 producing output wavelengths in the near UV is shown to be useful for the measurement of ozone in an altitude range from 15 to 50 km.

Analysis of Delays in Transmitting Time Code Using an Automated Computer Time Distribution System

DTIC Science & Technology

1999-12-01

jlevine@clock. bldrdoc.gov Abstract An automated computer time distribution system broadcasts standard tune to users using computers and modems via...contributed to &lays - sofhareplatform (50% of the delay), transmission speed of time- codes (25OA), telephone network (lS%), modem and others (10’4). The... modems , and telephone lines. Users dial the ACTS server to receive time traceable to the national time scale of Singapore, UTC(PSB). The users can in

WES (Waterways Experiment Station) Communications Plan for Voice and Data

DTIC Science & Technology

1989-01-01

modem on a leased line, and two wideband HDLC 56K connections not used on the Honeywell. 30. Honeywell DPS-8 configuration, as of October 1987, is as...based voice system to support additional asynchronous dial-up modem traffic. In June 1987, Dr. N. Radhakhrishnan of the WES Information Technology...voice system (PBX) and very low-speed data communications by the laboratories using 1,200/2,400-baud asynchronous modems over analog phone lines, and

Remote telescope control of site testing with ASCOM

NASA Astrophysics Data System (ADS)

Ji, Kaifan; Liang, Bo; Peng, Yajie; Wang, Feng

2012-04-01

Remote telescope control is significant important for the astronomical site testing. Basing on ASCOM standard, a prototype of remote telescope control system has been implemented. In this paper, the details of the system design, both server end and client end, are introduced. We tested the prototype on a narrow-band dial-up networking and controlled a real remote telescope successfully. The result indicates that it is effective to control remote telescope and other devices with ASCOM.

Use of the 'real-ear to dial difference' to derive real-ear SPL from hearing level obtained with insert earphones.

PubMed

Munro, K J; Lazenby, A

2001-10-01

The electroacoustic characteristics of a hearing instrument are normally selected for individuals using data obtained during audiological assessment. The precise inter-relationship between the electroacoustic and audiometric variables is most readily appreciated when they have been measured at the same reference point, such as the tympanic membrane. However, it is not always possible to obtain the real-ear sound pressure level (SPL) directly if this is below the noise floor of the probe-tube microphone system or if the subject is unco-operative. The real-ear SPL may be derived by adding the subject's real-ear to dial difference (REDD) acoustic transform to the audiometer dial setting. The aim of the present study was to confirm the validity of the Audioscan RM500 to measure the REDD with the ER-3A insert earphone. A probe-tube microphone was used to measure the real-ear SPL and REDD from the right ears of 16 adult subjects ranging in age from 22 to 41 years (mean age 27 years). Measurements were made from 0.25 kHz to 6 kHz at a dial setting of 70 dB with an ER-3A insert earphone and two earmould configurations: the EAR-LINK foam ear-tip and the subjects' customized skeleton earmoulds. Mean REDD varied as a function of frequency but was typically approximately 12 dB with a standard deviation (SD) of +/- 1.7 dB and +/- 2.7 dB for the foam ear-tip and customized earmould, respectively. The mean test-retest difference of the REDD varied with frequency but was typically 0.5 dB (SD 1 dB). Over the frequency range 0.5-4 kHz, the derived values were found to be within 5 dB of the measured values in 95% of subjects when using the EAR-LINK foam ear-tip and within 4 dB when using the skeleton earmould. The individually measured REDD transform can be used in clinical practice to derive a valid estimate of real-ear SPL when it has not been possible to measure this directly.

Comparisons of Airborne HSRL and Modeled Aerosol Profiles

NASA Astrophysics Data System (ADS)

Ferrare, R. A.; Burton, S. P.; Hostetler, C. A.; Hair, J. W.; Ismail, S.; Rogers, R. R.; Notari, A.; Berkoff, T.; Butler, C. F.; Collins, J. E., Jr.; Fenn, M. A.; Scarino, A. J.; Clayton, M.; Mueller, D.; Chemyakin, E.; Fast, J. D.; Berg, L. K.; Randles, C. A.; Colarco, P. R.; daSilva, A.

2014-12-01

Aerosol profiles derived from a regional and a global model are compared with aerosol profiles acquired by NASA Langley Research Center (LaRC) airborne High Spectral Resolution Lidars (HSRLs) during recent field missions. We compare simulated aerosol profiles obtained from the WRF-Chem regional model with those measured by the airborne HSRL-2 instrument over the Atlantic Ocean east of Cape Cod in July 2012 during the Department of Energy Two-Column Aerosol Project (TCAP). While deployed on the LaRC King Air during TCAP, HSRL-2 acquired profiles of aerosol extinction at 355 and 532 nm, as well as aerosol backscatter and depolarization at 355, 532, and 1064 nm. Additional HSRL-2 data products include profiles of aerosol type, mixed layer depth, and aerosol microphysical parameters (e.g. effective radius, concentration). The HSRL-2 and WRF-Chem aerosol profiles are compared along the aircraft flight tracks. HSRL-2 profiles acquired during the NASA Deriving Information on Surface Conditions from COlumn and VERtically Resolved Observations Relevant to Air Quality (DISCOVER-AQ) mission over Houston during September 2013 are compared with the NASA Goddard Earth Observing System global model, version 5 (GEOS-5) profiles. In addition to comparing backscatter and extinction profiles, the fraction of aerosol extinction and optical thickness from various aerosol species from GEOS-5 are compared with aerosol extinction and optical thickness contributed by aerosol types derived from HSRL-2 data. We also compare aerosol profiles modeled by GEOS-5 with those measured by the airborne LaRC DIAL/HSRL instrument during August and September 2013 when it was deployed on the NASA DC-8 for the Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys (SEAC4RS) mission. DIAL/HSRL measured extinction (532 nm), backscatter (532 and 1064 nm), and depolarization profiles (532 and 1064 nm) in both nadir and zenith directions during long transects over the continental United States. DIAL/HSRL measurements acquired during SEAC4RS allow comparisons with GEOS-5 simulations of forest fire smoke over the western U.S. The fraction of aerosol extinction attributed to dust derived from the DIAL/HSRL depolarization measurements are compared with the corresponding GEOS-5 dust simulations.

Lidar Technology at the Goddard Laser and Electro-Optics Branch

NASA Technical Reports Server (NTRS)

Heaps, William S.; Obenschain, Arthur F. (Technical Monitor)

2000-01-01

The Laser and Electro-Optics Branch at Goddard Space flight Center was established about three years ago to provide a focused center of engineering support and technology development in these disciplines with an emphasis on spaced based instruments for Earth and Space Science. The Branch has approximately 15 engineers and technicians with backgrounds in physics, optics, and electrical engineering. Members of the Branch are currently supporting a number of space based lidar efforts as well as several technology efforts aimed at enabling future missions. The largest effort within the Branch is support of the Ice, Cloud, and land Elevation Satellite (ICESAT) carrying the Geoscience Laser Altimeter System (GLAS) instrument. The ICESAT/GLAS primary science objectives are: 1) To determine the mass balance of the polar ice sheets and their contributions to global sea level change; and 2) To obtain essential data for prediction of future changes in ice volume and sea-level. The secondary science objectives are: 1) To measure cloud heights and the vertical structure of clouds and aerosols in the atmosphere; 2) To map the topography of land surfaces; and 3) To measure roughness, reflectivity, vegetation heights, snow-cover, and sea-ice surface characteristics. Our efforts have concentrated on the GLAS receiver component development, the Laser Reference Sensor for the Stellar Reference System, the GLAS fiber optics subsystems, and the prelaunch calibration facilities. We will report on our efforts in the development of the space qualified interference filter [Allan], etalon filter, photon counting detectors, etalor/laser tracking system, and instrument fiber optics, as well as specification and selection of the star tracker and development of the calibration test bed. We are also engaged in development work on lidar sounders for chemical species. We are developing new lidar technology to enable a new class of miniature lidar instruments that are compatible with small Discovery-class orbiters now in the NASA planetary program. The purpose of the lidar is to continuously profile the water vapor and dust in the Mars atmosphere from orbit in order to quantify its dynamics, their relationship in the diurnal cycles, and to infer water vapor exchange with the Mars surface. To remotely measure the water-vapor height profiles, we will use the differential absorption lidar (DIAL) technique. We are also developing a laser sensor for measuring the total column content of CO2 in the atmosphere of the earth. CO2 is the principal greenhouse gas and has increased by roughly 80 ppm in the last century and a half. We will report our efforts in the development of the laser transmitter and photon counting detector components for a Mars Orbiting DIAL system and for the CO2 sounder.

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT X, USE OF MEASURING TOOLS IN DIESEL MAINTENANCE.

ERIC Educational Resources Information Center

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE PRECISION MEASURING TOOLS USED IN DIESEL ENGINE MAINTENANCE. TOPICS ARE (1) LINEAR MEASURE, (2) MEASURING WITH RULES AND TAPES, (3) GETTING PRECISION WITH MICROMETERS, (4) DIAL INDICATORS, (5) TACHOMETERS, (6) TORQUE WRENCH, (7) THICKNESS (TECHER) GAGE, AND (8) VALVE…

Dialing Up an Embryo: Are Olfactory Receptors Digits in a Developmental Code?

ERIC Educational Resources Information Center

Travis, John

1998-01-01

Scientist William J. Dreyer has hypothesized that the cell surface proteins in the nose that detect odors also help assemble embryos. These olfactory receptors and related proteins act as identifiers, much like the last few digits of a telephone number, that help cells to find their intended neighbors in a developing embryo. Discusses the research…

National Household Education Survey. Adult and Course Data Files User's Manual.

ERIC Educational Resources Information Center

Brick, J. Michael; And Others

This manual provides documentation and guidance for users of the public release data files (adult file and course file) for Adult Education (AE) component of the 1991 National Household Education Survey (NHES:91). The NHES:91 was a random-digit dial telephone survey developed by the National Center for Education Statistics (NCES) and conducted by…

Atmospheric boundary layer CO2 remote sensing with a direct detection LIDAR instrument based on a widely tunable optical parametric source.

PubMed

Cadiou, Erwan; Mammez, Dominique; Dherbecourt, Jean-Baptiste; Gorju, Guillaume; Pelon, Jacques; Melkonian, Jean-Michel; Godard, Antoine; Raybaut, Myriam

2017-10-15

We report on the capability of a direct detection differential absorption lidar (DIAL) for range resolved and integrated path (IPDIAL) remote sensing of CO 2 in the atmospheric boundary layer (ABL). The laser source is an amplified nested cavity optical parametric oscillator (NesCOPO) emitting approximately 8 mJ at the two measurement wavelengths selected near 2050 nm. Direct detection atmospheric measurements are taken from the ground using a 30 Hz frequency switching between emitted wavelengths. Results show that comparable precision measurements are achieved in DIAL and IPDIAL modes (not better than a few ppm) on high SNR targets such as near range ABL aerosol and clouds, respectively. Instrumental limitations are analyzed and degradation due to cloud scattering variability is discussed to explain observed DIAL and IPDIAL limitations.

A Compact Mobile Ozone Lidar for Atmospheric Ozone and Aerosol Profiling

NASA Technical Reports Server (NTRS)

De Young, Russell; Carrion, William; Pliutau, Denis

2014-01-01

A compact mobile differential absorption lidar (DIAL) system has been developed at NASA Langley Research Center to provide ozone, aerosol and cloud atmospheric measurements in a mobile trailer for ground-based atmospheric ozone air quality campaigns. This lidar is integrated into the Tropospheric Ozone Lidar Network (TOLNet) currently made up of four other ozone lidars across the country. The lidar system consists of a UV and green laser transmitter, a telescope and an optical signal receiver with associated Licel photon counting and analog channels. The laser transmitter consist of a Q-switched Nd:YLF inter-cavity doubled laser pumping a Ce:LiCAF tunable UV laser with all the associated power and lidar control support units on a single system rack. The system has been configured to enable mobile operation from a trailer and was deployed to Denver, CO July 15-August 15, 2014 supporting the DISCOVER-AQ campaign. Ozone curtain plots and the resulting science are presented.

SEMG-controlled telephone interface for people with disabilities.

PubMed

Chen, Yu-Luen; Lai, Jin-Shin; Luh, Jer-Junn; Kuo, Te-Son

2002-01-01

This paper proposes the development of a surface electromyographic (SEMG)-controlled telephone interface for the disabled. The system is composed of three major components: (1) a SEMG receiving/signal-processing module; (2) a row-column scanning interface for the telephone dialling pad; and (3) a main controller, the Intel-8951 microprocessor. The design concept was based on the idea of using a SEMG generated by the disabled and converting it into a trigger pulse. This could allow convenient control of the dialing motion in the row-column scanning keys of a telephone dialling pad. People with disabilities are competent for certain kinds of work such as being a telephone operator. The increase of opportunities to perform a job for the disabled would help them live independently.

Lidar system for air-pollution monitoring over urban areas

NASA Astrophysics Data System (ADS)

Moskalenko, Irina V.; Shcheglov, Djolinard A.; Molodtsov, Nikolai A.

1997-05-01

The atmospheric environmental situation over the urban area of a large city is determined by a complex combination of anthropogenic pollution and meteorological factors. The efficient way to provide three-dimensional mapping of gaseous pollutants over wide areas is utilization of lidar systems employing tunable narrowband transmitters. The paper presented describes activity of RRC 'Kurchatov Institute' in the field of lidar atmospheric monitoring. The project 'mobile remote sensing system based on tunable laser transmitter for environmental monitoring' is developed under financial support of International Scientific and Technology Center (Moscow). The objective of the project is design, construction and field testing of a DIAL-technique system. The lidar transmitter consists of an excimer laser pumping dye laser, BBO crystal frequency doubler, and scanning flat mirror. Sulfur dioxide and atomic mercury have been selected as pollutants for field tests of the lidar system under development. A recent large increase in Moscow traffic stimulated taking into consideration also the remote sensing of lower troposphere ozone because of the photochemical smog problem. The status of the project is briefly discussed. The current activity includes also collecting of environmental data relevant to lidar remote sensing. Main attention is paid to pollutant concentration levels over Moscow city and Moscow district areas.

Airborne differential absorption lidar system for water vapor investigations

NASA Technical Reports Server (NTRS)

Browell, E. V.; Carter, A. F.; Wilkerson, T. D.

1981-01-01

Range-resolved water vapor measurements using the differential-absorption lidar (DIAL) technique is described in detail. The system uses two independently tunable optically pumped lasers operating in the near infrared with laser pulses of less than 100 microseconds separation, to minimize concentration errors caused by atmospheric scattering. Water vapor concentration profiles are calculated for each measurement by a minicomputer, in real time. The work is needed in the study of atmospheric motion and thermodynamics as well as in forestry and agriculture problems.

Advanced Information Systems Design: Technical Basis and Human Factors Review Guidance

DTIC Science & Technology

2000-03-01

D ., Wise, J ., and Hanes, L., "An Evaluation of Nuclear Power Plant Safety Parameter Display Systems," Proceedings of the Human Factors Society 25th...Reactor (PWR) (Source: Reprinted with permission from Woods, D ., Wise, J ., and Hanes, L., "An Evaluation of Nuclear Power Plant Safety Parameter...Dials display rpCJni?3 (b) Fluid-Tanks display B (c) Seesaw display I 72 CF \\^- J B ’ V ’II ’ ( d ) Mimic display B E * • \\ ^r 7

Remote Sensing of Turbine Engine Gases.

DTIC Science & Technology

1981-09-30

Institute by lasers operating in the infrared compared to the visible and of Technology. Lexington, M A 0217 3. UV region. 00l8.9197/81/0900-1917S00.75 0...mini-TEA lasers used in both single- and dual- laser consists of a UV -preionized discharge between Rogowski laser DIAL systems, and a study has been...described previously [10]. The discharge is thyratron system. This research has led to a better understanding of triggered and may operate at a pulse

An Automated Tool to Enable the Distributed Operations of Air Force Satellites

DTIC Science & Technology

2002-01-01

workstations, home PCs, PDAs, pagers) over connections with various bandwidths (e.g., dial-up 56k , wireless 9.6k), SERS has different USis to support the...demonstration and evaluation activities, and (3) CERES employs more modem and open ground systems than are currently deployed in the space operations...COTS or custom tools. • Yes, we demonstrated that our software can interface with a modem Air Force ground system (CERES’ COBRA). • We identified new

MAGTF (Marine Air Ground Task Force) Data Transfer Alternatives (1986-1996).

DTIC Science & Technology

1986-04-01

Devices currently on the market offer circuit conditioning and access control as well as the required dial-up connectivity. A program to provide dial... UGC -74A(V)3 Communication Terminal (Teletype Writer (TTY) CV-3591 Advanced Narrowband Digital Voice Terminal (ANDVT) AN/TGC-46 TTY Central (part of AN...interface directly with both AN/ UGC -74 TTY and ADPE-FMF/EUC equipment over serial circuits. 5.5.2.2 Switching Equipment. Switching equipments perform the

Impact of Monetary Incentives and Mailing Procedures: An Experiment in a Federally Sponsored Telephone Survey. Methodology Report. NCES 2006-066

ERIC Educational Resources Information Center

Brick, J. Michael; Hagedorn, Mary Collins; Montaquila, Jill; Roth, Shelley Brock; Chapman, Christopher

2006-01-01

The National Household Education Surveys Program (NHES) includes a series of random digit dial (RDD) surveys developed by the National Center for Education Statistics (NCES) in the Institute of Education Sciences, U.S. Department of Education. It is designed to collect information on important educational issues through telephone surveys of…

Lidar stratospheric ozone measurements at the observatoire de Haute Provence (France)

NASA Technical Reports Server (NTRS)

Godin, S.; Pelon, J.; Megie, G.

1986-01-01

Strastospheric ozone monitoring is of particular importance to confirm present day theories predicting a maximal ozone depletion, due to chlorofluorocarbon emission, in the 35 to 45 km altitude range. Measurements presently rely on both ground based and satellite-borne passive experiments. Such systems have been recently shown to have intrinsic limitations mainly due to atmospheric aerosol presence and calibration problems. During the last few years, active lidar profiling of the ozone vertical distribution by the Differential Absorption Laser technique (DIAL) in the UV wavelength range has been developed using two different laser sources: a Nd-YAG pumped dye laser which enables a large tuning range of the UV emitted wavelengths; and exciplex laser sources using xenon chloride as an active medium and emitting at 308 nm, the off wavelength being usually generated by Raman shifting techniques. Advantages and limitations of using both of these systems are briefly discussed.

Development of a Coherent Differential Absorption Lidar for Range Resolved Atmospheric CO2 Measurements

NASA Technical Reports Server (NTRS)

Yu, Jirong; Petros, Mulgueta; Chen, Songsheng; Bai, Yingxin; Petzar, Paul J.; Trieu, Bo. C.; Koch, Grady J.; Beyon, Jeffery J.; Singh, Upendra N.

2010-01-01

A pulsed, 2-m coherent Differential Absorption Lidar (DIAL) / Integrated Path Differential Absorption (IPDA) transceiver, developed under the Laser Risk Reduction Program (LRRP) at NASA, is integrated into a fully functional lidar instrument. This instrument will measure atmospheric CO2 profiles (by DIAL) initially from a ground platform, and then be prepared for aircraft installation to measure the atmospheric CO2 column densities in the atmospheric boundary layer (ABL) and lower troposphere. The airborne prototype CO2 lidar can measure atmospheric CO2 column density in a range bin of 1km with better than 1.5% precision at horizontal resolution of less than 50km. It can provide the image of the pooling of CO2 in lowlying areas and performs nighttime mass balance measurements at landscape scale. This sensor is unique in its capability to study the vertical ABL-free troposphere exchange of CO2 directly. It will allow the investigators to pursue subsequent in science-driven deployments, and provides a unique tool for Active Sensing of CO2 Emissions over Night, Days, and Seasons (ASCENDS) validation that was strongly advocated in the recent ASCENDS Workshop.

Proposed standardized definitions for vertical resolution and uncertainty in the NDACC lidar ozone and temperature algorithms - Part 2: Ozone DIAL uncertainty budget

NASA Astrophysics Data System (ADS)

Leblanc, Thierry; Sica, Robert J.; van Gijsel, Joanna A. E.; Godin-Beekmann, Sophie; Haefele, Alexander; Trickl, Thomas; Payen, Guillaume; Liberti, Gianluigi

2016-08-01

A standardized approach for the definition, propagation, and reporting of uncertainty in the ozone differential absorption lidar data products contributing to the Network for the Detection for Atmospheric Composition Change (NDACC) database is proposed. One essential aspect of the proposed approach is the propagation in parallel of all independent uncertainty components through the data processing chain before they are combined together to form the ozone combined standard uncertainty. The independent uncertainty components contributing to the overall budget include random noise associated with signal detection, uncertainty due to saturation correction, background noise extraction, the absorption cross sections of O3, NO2, SO2, and O2, the molecular extinction cross sections, and the number densities of the air, NO2, and SO2. The expression of the individual uncertainty components and their step-by-step propagation through the ozone differential absorption lidar (DIAL) processing chain are thoroughly estimated. All sources of uncertainty except detection noise imply correlated terms in the vertical dimension, which requires knowledge of the covariance matrix when the lidar signal is vertically filtered. In addition, the covariance terms must be taken into account if the same detection hardware is shared by the lidar receiver channels at the absorbed and non-absorbed wavelengths. The ozone uncertainty budget is presented as much as possible in a generic form (i.e., as a function of instrument performance and wavelength) so that all NDACC ozone DIAL investigators across the network can estimate, for their own instrument and in a straightforward manner, the expected impact of each reviewed uncertainty component. In addition, two actual examples of full uncertainty budget are provided, using nighttime measurements from the tropospheric ozone DIAL located at the Jet Propulsion Laboratory (JPL) Table Mountain Facility, California, and nighttime measurements from the JPL stratospheric ozone DIAL located at Mauna Loa Observatory, Hawai'i.

Advanced 2-micron Solid-state Laser for Wind and CO2 Lidar Applications

NASA Technical Reports Server (NTRS)

Yu, Jirong; Trieu, Bo C.; Petros, Mulugeta; Bai, Yingxin; Petzar, Paul J.; Koch, Grady J.; Singh, Upendra N.; Kavaya, Michael J.

2006-01-01

Significant advancements in the 2-micron laser development have been made recently. Solid-state 2-micron laser is a key subsystem for a coherent Doppler lidar that measures the horizontal and vertical wind velocities with high precision and resolution. The same laser, after a few modifications, can also be used in a Differential Absorption Lidar (DIAL) system for measuring atmospheric CO2 concentration profiles. The world record 2-micron laser energy is demonstrated with an oscillator and two amplifiers system. It generates more than one joule per pulse energy with excellent beam quality. Based on the successful demonstration of a fully conductive cooled oscillator by using heat pipe technology, an improved fully conductively cooled 2-micron amplifier was designed, manufactured and integrated. It virtually eliminates the running coolant to increase the overall system efficiency and reliability. In addition to technology development and demonstration, a compact and engineering hardened 2-micron laser is under development. It is capable of producing 250 mJ at 10 Hz by an oscillator and one amplifier. This compact laser is expected to be integrated to a lidar system and take field measurements. The recent achievements push forward the readiness of such a laser system for space lidar applications. This paper will review the developments of the state-of-the-art solid-state 2-micron laser.

Intelligent Advanced Communications IP Telephony Feasibility for the US Navy - Phase 3

DTIC Science & Technology

2011-03-01

atlanta.example.com CSeq: 1 BYE Content-Length: 0 Figure 2- 4 SIP Message Details 2.6.8 Implementation of Selected Features Below we examine a set of...34.priority" where priority is one of the following values: 0 Routine (lowest priority) 2 Priority 4 Immediate 6 Flash 8 Flash...cm/dial?poolId= 0 &uri=5553002 HTTPC: <-- : 192.168.0.135:8080 /cm/dial?poolId= 0 &uri=5553002 HTTPC: Closed : 192.168.0.135:8080 4

Address-based versus random-digit-dial surveys: comparison of key health and risk indicators.

PubMed

Link, Michael W; Battaglia, Michael P; Frankel, Martin R; Osborn, Larry; Mokdad, Ali H

2006-11-15

Use of random-digit dialing (RDD) for conducting health surveys is increasingly problematic because of declining participation rates and eroding frame coverage. Alternative survey modes and sampling frames may improve response rates and increase the validity of survey estimates. In a 2005 pilot study conducted in six states as part of the Behavioral Risk Factor Surveillance System, the authors administered a mail survey to selected household members sampled from addresses in a US Postal Service database. The authors compared estimates based on data from the completed mail surveys (n = 3,010) with those from the Behavioral Risk Factor Surveillance System telephone surveys (n = 18,780). The mail survey data appeared reasonably complete, and estimates based on data from the two survey modes were largely equivalent. Differences found, such as differences in the estimated prevalences of binge drinking (mail = 20.3%, telephone = 13.1%) or behaviors linked to human immunodeficiency virus transmission (mail = 7.1%, telephone = 4.2%), were consistent with previous research showing that, for questions about sensitive behaviors, self-administered surveys generally produce higher estimates than interviewer-administered surveys. The mail survey also provided access to cell-phone-only households and households without telephones, which cannot be reached by means of standard RDD surveys.

Programming for energy monitoring/display system in multicolor lidar system research

NASA Technical Reports Server (NTRS)

Alvarado, R. C., Jr.; Allen, R. J.

1982-01-01

The Z80 microprocessor based computer program that directs and controls the operation of the six channel energy monitoring/display system that is a part of the NASA Multipurpose Airborne Differential Absorption Lidar (DIAL) system is described. The program is written in the Z80 assembly language and is located on EPROM memories. All source and assembled listings of the main program, five subroutines, and two service routines along with flow charts and memory maps are included. A combinational block diagram shows the interfacing (including port addresses) between the six power sensors, displays, front panel controls, the main general purpose minicomputer, and this dedicated microcomputer system.

Collocation and Pattern Recognition Effects on System Failure Remediation

NASA Technical Reports Server (NTRS)

Trujillo, Anna C.; Press, Hayes N.

2007-01-01

Previous research found that operators prefer to have status, alerts, and controls located on the same screen. Unfortunately, that research was done with displays that were not designed specifically for collocation. In this experiment, twelve subjects evaluated two displays specifically designed for collocating system information against a baseline that consisted of dial status displays, a separate alert area, and a controls panel. These displays differed in the amount of collocation, pattern matching, and parameter movement compared to display size. During the data runs, subjects kept a randomly moving target centered on a display using a left-handed joystick and they scanned system displays to find a problem in order to correct it using the provided checklist. Results indicate that large parameter movement aided detection and then pattern recognition is needed for diagnosis but the collocated displays centralized all the information subjects needed, which reduced workload. Therefore, the collocated display with large parameter movement may be an acceptable display after familiarization because of the possible pattern recognition developed with training and its use.

Interpretation of DIAL Measurements of Lower Stratospheric Ozone in Regions with Pinatubo Aerosols

NASA Technical Reports Server (NTRS)

Grant, William B.; Browell, Edward V.; Fenn, Marta A.; Butler, Carolyn F.; Brackett, Vincent G.; Veiga, Robert E.; Mayor, Shane D.; Fishman, Jack; Nganga, D.; Minga, A.

1992-01-01

The influence of volcanic aerosols on stratospheric ozone is a topic of current interest, especially with the June 15, 1991 eruption of Mt. Pinatubo in the Philippines. Lidar has been used in the past to provide aerosol profiles which could be compared with ozone profiles measured using ozonesondes to look for coincidences between volcanic aerosols and ozone decreases. The differential absorption lidar (DIAL) technique has the advantages of being able to measure ozone and aerosol profiles simultaneously as well as being able to cover large geographical regions rapidly. While there are problems associated with correcting the ozone profiles for the presence of aerosols, the corrections can be made reliably when the wavelengths are closely spaced and the Bernoulli method is applied. The DIAL measurements considered in this paper are those obtained in the tropical stratosphere in January 1992 during the Airborne Arctic Stratospheric Expedition (AASE-II). The determination of ozone profiles in the presence of Pinatubo aerosols is discussed in a companion paper.

Raman shifting of KrF laser radiation for tropospheric ozone measurements

NASA Technical Reports Server (NTRS)

Grant, William B.; Browell, Edward V.; Higdon, Noah S.; Ismail, Syed

1991-01-01

The differential absorption lidar (DIAL) measurement of tropospheric ozone requires use of high average power UV lasers operating at two appropriate DIAL wavelengths. Laboratory experiments have demonstrated that a KrF excimer laser can be used to generate several wavelengths with good energy conversion efficiencies by stimulated Raman shifting using hydrogen (H2) and deuterium (D2). Computer simulations for an airborne lidar have shown that these laser emissions can be used for the less than 5 percent random error, high resolution measuremment of ozone across the troposphere using the DIAL technique. In the region of strong ozone absorption, laser wavelengths of 277.0 and 291.7 nm were generated using H2 and D2, respectively. In addition, a laser wavelength at 302.0 nm was generated using two cells in series, with the first containing D2 and the second containing H2. The energy conversion efficiency for each wavelength was between 14 and 27 percent.

UV Lidar Receiver Analysis for Tropospheric Sensing of Ozone

NASA Technical Reports Server (NTRS)

Pliutau, Denis; DeYoung, Russell J.

2013-01-01

A simulation of a ground based Ultra-Violet Differential Absorption Lidar (UV-DIAL) receiver system was performed under realistic daytime conditions to understand how range and lidar performance can be improved for a given UV pulse laser energy. Calculations were also performed for an aerosol channel transmitting at 3 W. The lidar receiver simulation studies were optimized for the purpose of tropospheric ozone measurements. The transmitted lidar UV measurements were from 285 to 295 nm and the aerosol channel was 527-nm. The calculations are based on atmospheric transmission given by the HITRAN database and the Modern Era Retrospective Analysis for Research and Applications (MERRA) meteorological data. The aerosol attenuation is estimated using both the BACKSCAT 4.0 code as well as data collected during the CALIPSO mission. The lidar performance is estimated for both diffuseirradiance free cases corresponding to nighttime operation as well as the daytime diffuse scattered radiation component based on previously reported experimental data. This analysis presets calculations of the UV-DIAL receiver ozone and aerosol measurement range as a function of sky irradiance, filter bandwidth and laser transmitted UV and 527-nm energy

An Evaluation of Bias in the 2007 National Household Education Surveys Program: Results from a Special Data Collection Effort. NCES 2009-029

ERIC Educational Resources Information Center

Van de Kerckhove, Wendy; Montaquila, Jill M.; Carver, Priscilla R.; Brick, J. Michael

2009-01-01

The National Household Education Surveys Program (NHES) is a random digit dialing (RDD) survey program developed by the National Center for Education Statistics (NCES) in the Institute of Education Sciences, U.S. Department of Education. The surveys are designed to help NCES collect data directly from households about important education topics.…

Runway Rubber Removal Specification Development: Field Evaluation Procedures Development.

DTIC Science & Technology

1984-07-01

removal was sufficient enough to restore full pave- ment skid resistance (based on tests with a DBV). With regard to high-pressure water rubber ...over a test surface, the rubber slider resists motion-. The force, parallel to the test surface, which acts on the slider registers an output on a dial...PROCEDURE 1. Check rubber shoe for wear . Replace when the edge is worn by more than 3/16 in as measured with a rule laid flat across the slider width. 2

Effect of tibial positioning on the diagnosis of posterolateral rotatory instability in the posterior cruciate ligament-deficient knee.

PubMed

Strauss, Eric J; Ishak, Charbel; Inzerillo, Christopher; Walsh, Michael; Yildirim, Gokce; Walker, Peter; Jazrawi, Laith; Rosen, Jeffrey

2007-08-01

To determine whether positioning of the tibia affects the degree of tibial external rotation seen during a dial test in the posterior cruciate ligament (PCL)-posterolateral corner (PLC)-deficient knee. Laboratory investigation. Biomechanics laboratory. An anterior force applied to the tibia in the combined PCL-PLC-deficient knee will yield increased tibial external rotation during a dial test. The degree of tibial external rotation was measured with 5 Nm of external rotation torque applied to the tibia at both 30 degrees and 90 degrees of knee flexion. Before the torque was applied, an anterior force, a posterior force, or neutral (normal, reduced control) force was applied to the tibia. External rotation measurements were repeated after sequential sectioning of the PCL, the posterolateral structures and the fibular collateral ligament (FCL). Baseline testing of the intact specimens demonstrated a mean external rotation of 18.6 degrees with the knee flexed to 30 degrees (range 16.1-21.0 degrees ), and a mean external rotation of 17.3 degrees with the knee flexed to 90 degrees (range 13.8-20.0 degrees ). Sequential sectioning of the PCL, popliteus and popliteofibular ligament, and the FCL led to a significant increase in tibial external rotation compared with the intact knee for all testing scenarios. After sectioning of the popliteus and popliteofibular ligament, the application of an anterior force during testing led to a mean tibial external rotation that was 5 degrees greater than during testing in the neutral position and 7.5 degrees greater than during testing with a posterior force. In the PCL, popliteus/popliteofibular ligament and FCL-deficient knee, external rotation was 9 degrees and 12 degrees greater with the application of an anterior force during testing compared with neutral positioning and the application of a posterior force, respectively. An anterior force applied to the tibia during the dial test in a combined PCL-PLC-injured knee increased the overall amount of observed tibial external rotation during the dial test. The anterior force reduced the posterior tibial subluxation associated with PCL injury, which is analogous to what is observed when the dial test is performed with the patient in the prone position. Reducing the tibia with either an anterior force when the patient is supine or performing the dial test with the patient in the prone position increases the ability of an examiner to detect a concomitant PLC injury in the setting of a PCL-deficient knee.

The effect of proximal tibial slope on dynamic stability testing of the posterior cruciate ligament- and posterolateral corner-deficient knee.

PubMed

Petrigliano, Frank A; Suero, Eduardo M; Voos, James E; Pearle, Andrew D; Allen, Answorth A

2012-06-01

Proximal tibial slope has been shown to influence anteroposterior translation and tibial resting point in the posterior cruciate ligament (PCL)-deficient knee. The effect of proximal tibial slope on rotational stability of the knee is unknown. Change in proximal tibial slope produced via osteotomy can influence both static translation and dynamic rotational kinematics in the PCL/posterolateral corner (PLC)-deficient knee. Controlled laboratory study. Posterior drawer, dial, and mechanized reverse pivot-shift (RPS) tests were performed on hip-to-toe specimens and translation of the lateral and medial compartments measured utilizing navigation (n = 10). The PCL and structures of the PLC were then sectioned. Stability testing was repeated, and compartmental translation was recorded. A proximal tibial osteotomy in the sagittal plane was then performed achieving either +5° or -5° of tibial slope variation, after which stability testing was repeated (n = 10). Analysis was performed using 1-way analysis of variance (ANOVA; α = .05). Combined sectioning of the PCL and PLC structures resulted in a 10.5-mm increase in the posterior drawer, 15.5-mm increase in the dial test at 30°, 14.5-mm increase in the dial test at 90°, and 17.9-mm increase in the RPS (vs intact; P < .05). Increasing the posterior slope (high tibial osteotomy [HTO] +5°) in the PCL/PLC-deficient knee reduced medial compartment translation by 3.3 mm during posterior drawer (vs deficient; P < .05) but had no significant effect on the dial test at 30°, dial test at 90°, or RPS. Conversely, reversing the slope (HTO -5°) caused a 4.8-mm increase in medial compartment translation (vs deficient state; P < .05) during posterior drawer and an 8.6-mm increase in lateral compartment translation and 9.0-mm increase in medial compartment translation during RPS (vs deficient state; P < .05). Increasing posterior tibial slope diminished static posterior instability of the PCL/PLC-deficient knee as measured by the posterior drawer test but had little effect on rotational or dynamic multiplanar stability as assessed by the dial and RPS tests, respectively. Conversely, decreasing posterior slope resulted in increased posterior instability and a significant increase in the magnitude of the RPS. These results suggest that increasing posterior tibial slope may improve sagittal stability in the PCL/PLC-deficient knee. Moreover, a knee with diminished posterior tibial slope may demonstrate greater multiplanar instability in this setting. Consequently, proximal tibial slope should be considered when treating combined PCL/PLC injuries of the knee.

Bringing the medical library to the office desktop.

PubMed

Brown, S R; Decker, G; Pletzke, C J

1991-01-01

This demonstration illustrates LRC Remote Computer Services- a dual operating system, multi-protocol system for delivering medical library services to the medical professional's desktop. A working model draws resources from CD-ROM and magnetic media file services, Novell and AppleTalk network protocol suites and gating, LAN and asynchronous (dial-in) access strategies, commercial applications for MS-DOS and Macintosh workstations and custom user interfaces. The demonstration includes a discussion of issues relevant to the delivery of said services, particularly with respect to maintenance, security, training/support, staffing, software licensing and costs.

Complementarity of UV and IR differential absorption lidar for global measurements of atmospheric species

NASA Technical Reports Server (NTRS)

Megie, G.; Menzies, R. T.

1980-01-01

An analysis of the potential capabilities of a spectrally diversified DIAL technique for monitoring atmospheric species is presented assuming operation from an earth-orbiting platform. Emphasis is given to the measurement accuracies and spatial and temporal resolutions required to meet present atmospheric science objectives. The discussion points out advantages of spectral diversity to perform comprehensive studies of the atmosphere; in general it is shown that IR systems have an advantage in lower atmospheric measurements, while UV systems are superior for middle and upper atmospheric measurements.

Real-Time, Wide Area Dispatch of Mobil Tank Trucks

DTIC Science & Technology

1987-01-01

human dispatchers it assists. Using CAD, Mobil has substantially re- duced costs and staff while improving customer service. I n the spring of 1985, a...process by establishing the Mobil order response center (MORC). To use MORC, the customer dials a toll-free number, available 24 hours a day, seven...MATS Figwe 3: Mobil light products order and dispatch information flow. Customers call an audio re- sponse computer system named MORC ( Mobil order

Magnetic heading reference

NASA Technical Reports Server (NTRS)

Garner, H. D. (Inventor)

1977-01-01

This invention employs a magnetometer as a magnetic heading reference for a vehicle such as a small aircraft. The magnetometer is mounted on a directional dial in the aircraft in the vicinity of the pilot such that it is free to turn with the dial about the yaw axis of the aircraft. The invention includes a circuit for generating a signal proportional to the northerly turning error produced in the magnetometer due to the vertical component of the earth's magnetic field. This generated signal is then subtracted from the output of the magnetometer to compensate for the northerly turning error.

Design of Instrument Dials for Maximum Legibility. Part 5. Origin Location, Scale Break, Number Location, and Contrast Direction

DTIC Science & Technology

1951-05-01

prccedur&:s to be of hipn accuracy. Ambij;uity of subject responizes due to overlap of entries on tU,, record sheets vas negligible. Handwriting ...experimental variables on reading errors us carried out by analysis of variance methods. For this purpose it was convenient to consider different classes...on any scale - an error ofY one numbered division. For this reason, the result. of the analysis of variance of the /10’s errors by dial types may

III-V Compound Detectors for CO2 DIAL Measurements

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Abedin, M. Nurul; Sulima, Oleg V.; Ismail, Syed; Singh, Upendra N.

2005-01-01

Profiling of atmospheric carbon dioxide (CO2) is important for understanding the natural carbon cycle on Earth and its influence on global warming and climate change. Differential absorption lidar is a powerful remote sensing technique used for profiling and monitoring atmospheric constituents. Recently there has been an interest to apply this technique, at the 2 m wavelength, for investigating atmospheric CO2. This drives the need for high quality detectors at this wavelength. Although 2 m detectors are commercially available, the quest for a better detector is still on. The detector performance, regarding quantum efficiency, gain and associated noise, affects the DIAL signal-to-noise ratio and background signal, thereby influencing the instrument sensitivity and dynamic range. Detectors based on the III-V based compound materials shows a strong potential for such application. In this paper the detector requirements for a long range CO2 DIAL profiles will be discussed. These requirements were compared to newly developed III-V compound infrared detectors. The performance of ternary InGaSb pn junction devices will be presented using different substrates, as well as quaternary InGaAsSb npn structure. The performance study was based on experimental characterization of the devices dark current, spectral response, gain and noise. The final results are compared to the current state-of-the-art InGaAs technology. Npn phototransistor structure showed the best performance, regarding the internal gain and therefore the device signal-to-noise ratio. 2-micrometers detectivity as high as 3.9 x 10(exp 11) cmHz(sup 1/2)/W was obtained at a temperature of -20 C and 4 V bias voltage. This corresponds to a responsivity of 2650 A/W with about 60% quantum efficiency.

Tropospheric ozone profiles by DIAL at Maïdo Observatory (Reunion Island): system description, instrumental performance and result comparison with ozone external data set

NASA Astrophysics Data System (ADS)

Duflot, Valentin; Baray, Jean-Luc; Payen, Guillaume; Marquestaut, Nicolas; Posny, Francoise; Metzger, Jean-Marc; Langerock, Bavo; Vigouroux, Corinne; Hadji-Lazaro, Juliette; Portafaix, Thierry; De Mazière, Martine; Coheur, Pierre-Francois; Clerbaux, Cathy; Cammas, Jean-Pierre

2017-09-01

In order to recognize the importance of ozone (O3) in the troposphere and lower stratosphere in the tropics, a DIAL (differential absorption lidar) tropospheric O3 lidar system (LIO3TUR) was developed and installed at the Université de la Réunion campus site (close to the sea) on Reunion Island (southern tropics) in 1998. From 1998 to 2010, it acquired 427 O3 profiles from the low to the upper troposphere and has been central to several studies. In 2012, the system was moved up to the new Maïdo Observatory facility (2160 m a.m.s.l. - metres above mean sea level) where it started operation in February 2013. The current system (LIO3T) configuration generates a 266 nm beam obtained with the fourth harmonic of a Nd:YAG laser sent into a Raman cell filled up with deuterium (using helium as buffer gas), generating the 289 and 316 nm beams to enable the use of the DIAL method for O3 profile measurements. The optimal range for the actual system is 6-19 km a.m.s.l., depending on the instrumental and atmospheric conditions. For a 1 h integration time, vertical resolution varies from 0.7 km at 6 km a.m.s.l. to 1.3 km at 19 km a.m.s.l., and mean uncertainty within the 6-19 km range is between 6 and 13 %. Comparisons with eight electrochemical concentration cell (ECC) sondes simultaneously launched from the Maïdo Observatory show good agreement between data sets with a 6.8 % mean absolute relative difference (D) between 6 and 17 km a.m.s.l. (LIO3T lower than ECC). Comparisons with 37 ECC sondes launched from the nearby Gillot site during the daytime in a ±24 h window around lidar shooting result in a 9.4 % D between 6 and 19 km a.m.s.l. (LIO3T lower than ECC). Comparisons with 11 ground-based Network for Detection of Atmospheric Composition Change (NDACC) Fourier transform infrared (FTIR) spectrometer measurements acquired during the daytime in a ±24 h window around lidar shooting show good agreement between data sets with a D of 11.8 % for the 8.5-16 km partial column (LIO3T higher than FTIR), and comparisons with 39 simultaneous Infrared Atmospheric Sounding Interferometer (IASI) observations over Reunion Island show good agreement between data sets with a D of 11.3 % for the 6-16 km partial column (LIO3T higher than IASI). ECC, LIO3TUR and LIO3T O3 monthly climatologies all exhibit the same range of values and patterns. In particular, the Southern Hemisphere biomass burning seasonal enhancement and the ozonopause altitude decrease in late austral winter-spring, as well as the sign of deep convection bringing boundary layer O3-poor air masses up to the middle-upper troposphere in late austral summer, are clearly visible in all data sets.

MyOcean Internal Information System (Dial-P)

NASA Astrophysics Data System (ADS)

Blanc, Frederique; Jolibois, Tony; Loubrieu, Thomas; Manzella, Giuseppe; Mazzetti, Paolo; Nativi, Stefano

2010-05-01

MyOcean is a three-year project (2008-2011) which goal is the development and pre-operational validation of the GMES Marine Core Service for ocean monitoring and forecasting. It's a transition project that will conduct the European "operational oceanography" community towards the operational phase of a GMES European service, which demands more European integration, more operationality, and more service. Observations, model-based data, and added-value products will be generated - and enhanced thanks to dedicated expertise - by the following production units: • Five Thematic Assembly Centers, each of them dealing with a specific set of observation data: Sea Level, Ocean colour, Sea Surface Temperature, Sea Ice & Wind, and In Situ data, • Seven Monitoring and Forecasting Centers to serve the Global Ocean, the Arctic area, the Baltic Sea, the Atlantic North-West shelves area, the Atlantic Iberian-Biscay-Ireland area, the Mediterranean Sea and the Black sea. Intermediate and final users will discover, view and get the products by means of a central web desk, a central re-active manned service desk and thematic experts distributed across Europe. The MyOcean Information System (MIS) is considering the various aspects of an interoperable - federated information system. Data models support data and computer systems by providing the definition and format of data. The possibility of including the information in the data file is depending on data model adopted. In general there is little effort in the actual project to develop a ‘generic' data model. A strong push to develop a common model is provided by the EU Directive INSPIRE. At present, there is no single de-facto data format for storing observational data. Data formats are still evolving, with their underlying data models moving towards the concept of Feature Types based on ISO/TC211 standards. For example, Unidata are developing the Common Data Model that can represent scientific data types such as point, trajectory, station, grid, etc., which will be implemented in netCDF format. SeaDataNet is recommending ODV and NetCDF formats. Another problem related to data curation and interoperability is the possibility to use common vocabularies. Common vocabularies are developed in many international initiatives, such as GEMET (promoted by INSPIRE as a multilingual thesaurus), UNIDATA, SeaDataNet, Marine Metadata Initiative (MMI). MIS is considering the SeaDataNet vocabulary as a base for interoperability. Four layers of different abstraction levels of interoperability an be defined: - Technical/basic: this layer is implemented at each TAC or MFC through internet connection and basic services for data transfer and browsing (e.g FTP, HTTP, etc). - Syntactic: allowing the interchange of metadata and protocol elements. This layer corresponds to a definition Core Metadata Set, the format of exchange/delivery for the data and associated metadata and possible software. This layer is implemented by the DIAL-P logical interface (e.g. adoption of INSPIRE compliant metadata set and common data formats). - Functional/pragmatic: based on a common set of functional primitives or on a common set of service definitions. This layer refers to the definition of services based on Web services standards. This layer is implemented by the DIAL-P logical interface (e.g. adoption of INSPIRE compliant network services). - Semantic: allowing to access similar classes of objects and services across multiple sites, with multilinguality of content as one specific aspect. This layer corresponds to MIS interface, terminology and thesaurus. Given the above requirements, the proposed solution is a federation of systems, where the individual participants are self-contained autonomous systems, but together form a consistent wider picture. A mid-tier integration layer mediates between existing systems, adapting their data and service model schema to the MIS. The developed MIS is a read-only system, i.e. does not allow updating (or inserting) data into the participant resource systems. The main advantages of the proposed approach are: • to enable information sources to join the MIS and publish their data and metadata in a secure way, without any modification to their existing resources and procedures and without any restriction to their autonomy; • to enable users to browse and query the MIS, receiving an aggregated result incorporating relevant data and metadata from across different sources; • to accommodate the growth of such a MIS, either in terms of its clients or of its information resources, as well as the evolution of the underlying data model.

Simple force feedback for small virtual environments

NASA Astrophysics Data System (ADS)

Schiefele, Jens; Albert, Oliver; van Lier, Volker; Huschka, Carsten

1998-08-01

In today's civil flight training simulators only the cockpit and all its interaction devices exist as physical mockups. All other elements such as flight behavior, motion, sound, and the visual system are virtual. As an extension to this approach `Virtual Flight Simulation' tries to subsidize the cockpit mockup by a 3D computer generated image. The complete cockpit including the exterior view is displayed on a Head Mounted Display (HMD), a BOOM, or a Cave Animated Virtual Environment. In most applications a dataglove or virtual pointers are used as input devices. A basic problem of such a Virtual Cockpit simulation is missing force feedback. A pilot cannot touch and feel buttons, knobs, dials, etc. he tries to manipulate. As a result, it is very difficult to generate realistic inputs into VC systems. `Seating Bucks' are used in automotive industry to overcome the problem of missing force feedback. Only a seat, steering wheel, pedal, stick shift, and radio panel are physically available. All other geometry is virtual and therefore untouchable but visible in the output device. In extension to this concept a `Seating Buck' for commercial transport aircraft cockpits was developed. Pilot seat, side stick, pedals, thrust-levers, and flaps lever are physically available. All other panels are simulated by simple flat plastic panels. They are located at the same location as their real counterparts only lacking the real input devices. A pilot sees the entire photorealistic cockpit in a HMD as 3D geometry but can only touch the physical parts and plastic panels. In order to determine task performance with the developed Seating Buck, a test series was conducted. Users press buttons, adapt dials, and turn knobs. In a first test, a complete virtual environment was used. The second setting had a plastic panel replacing all input devices. Finally, as cross reference the participants had to repeat the test with a complete physical mockup of the input devices. All panels and physical devices can be easily relocated to simulate a different type of cockpit. Maximal 30 minutes are needed for a complete adaptation. So far, an Airbus A340 and a generic cockpit are supported.

An Evaluation of Electric Motors for Ship Propulsion

DTIC Science & Technology

2003-06-01

AIM). Permanent magnet motors are more power dense than a comparatively sized in- duction motor. The permanent magnet motor has been chosen to...study. They include the axial flux, the ra- dial flux, and the transverse flux permanent magnet motors . Each motor has its unique advantages...to be ideal for ship propulsion, work is ongoing to develop the PMSM for ship propulsion. Permanent magnet motors are expected to have significant

Optimization of A 2-Micron Laser Frequency Stabilization System for a Double-Pulse CO2 Differential Absorption Lidar

NASA Technical Reports Server (NTRS)

Chen, Songsheng; Yu, Jirong; Bai, Yingsin; Koch, Grady; Petros, Mulugeta; Trieu, Bo; Petzar, Paul; Singh, Upendra N.; Kavaya, Michael J.; Beyon, Jeffrey

2010-01-01

A carbon dioxide (CO2) Differential Absorption Lidar (DIAL) for accurate CO2 concentration measurement requires a frequency locking system to achieve high frequency locking precision and stability. We describe the frequency locking system utilizing Frequency Modulation (FM), Phase Sensitive Detection (PSD), and Proportional Integration Derivative (PID) feedback servo loop, and report the optimization of the sensitivity of the system for the feed back loop based on the characteristics of a variable path-length CO2 gas cell. The CO2 gas cell is characterized with HITRAN database (2004). The method can be applied for any other frequency locking systems referring to gas absorption line.

Introducing heterogeneous users and vehicles into models and algorithms for the dial-a-ride problem.

PubMed

Parragh, Sophie N

2011-08-01

Dial-a-ride problems deal with the transportation of people between pickup and delivery locations. Given the fact that people are subject to transportation, constraints related to quality of service are usually present, such as time windows and maximum user ride time limits. In many real world applications, different types of users exist. In the field of patient and disabled people transportation, up to four different transportation modes can be distinguished. In this article we consider staff seats, patient seats, stretchers and wheelchair places. Furthermore, most companies involved in the transportation of the disabled or ill dispose of different types of vehicles. We introduce both aspects into state-of-the-art formulations and branch-and-cut algorithms for the standard dial-a-ride problem. Also a recent metaheuristic method is adapted to this new problem. In addition, a further service quality related issue is analyzed: vehicle waiting time with passengers aboard. Instances with up to 40 requests are solved to optimality. High quality solutions are obtained with the heuristic method.

Initial Development of a Metric to Describe the Level of Safety Associated with Piloting an Aircraft with Synthetic Vision Systems (SVS) Displays

NASA Technical Reports Server (NTRS)

Bartolone, Anthony P.; Glabb, Louis J.; Hughes, Monica F.; Parrish, Russell V.

2005-01-01

Synthetic Vision Systems (SVS) displays provide pilots with a continuous view of terrain combined with integrated guidance symbology in an effort to increase situation awareness (SA) and decrease workload during operations in Instrument Meteorological Conditions (IMC). It is hypothesized that SVS displays can replicate the safety and operational flexibility of flight in Visual Meteorological Conditions (VMC), regardless of actual out-the-window (OTW) visibility or time of day. Significant progress has been made towards evolving SVS displays as well as demonstrating their ability to increase SA compared to conventional avionics in a variety of conditions. While a substantial amount of data has been accumulated demonstrating the capabilities of SVS displays, the ability of SVS to replicate the safety and operational flexibility of VMC flight performance in all visibility conditions is unknown to any specific degree. In order to more fully quantify the relationship of flight operations in IMC with SVS displays to conventional operations conducted in VMC, a fundamental comparison to current day general aviation (GA) flight instruments was warranted. Such a comparison could begin to establish the extent to which SVS display concepts are capable of maintaining an "equivalent level of safety" with the round dials they could one day replace, for both current and future operations. A combination of subjective and objective data measures were used to quantify the relationship between selected components of safety that are associated with flying an approach. Four information display methods ranging from a "round dials" baseline through a fully integrated SVS package that includes terrain, pathway based guidance, and a strategic navigation display, were investigated in this high fidelity simulation experiment. In addition, a broad spectrum of pilots, representative of the GA population, were employed for testing in an attempt to enable greater application of the results and determine if "equivalent levels of safety" are achievable through the incorporation of SVS technology regardless of a pilot's flight experience.

Dial-A-Decon Solution Chemistry GAP Testing

DTIC Science & Technology

2012-04-01

34 The tubes were serially diluted using Buttcrfield’s buffer solution and plated in triplicate on Tryptic Soy Agar. Plates were enumerated the...of 200 uL HD to 10 mL of the surfactant solution. The energy to create the oil in water (O/W) emulsions was provided by magnetic stirring. Solutions...emulsify a mixture of water and oil such as HD, one or more emulsifiers are required. Each surfactant system can be characterized by an HLB value

Counter Electrical Generation and Distribution: An Assessment for Global Strike in 2035

DTIC Science & Technology

2012-02-15

magnetic field . Satellites in low earth orbit (LEO) or high earth orbit (HEO) orbits would be disabled from effects of the ionizing electrons on...of delivery.34 High power microwaves may also offer an ability to “dial down” the electro- magnetic fields being used to fine tune the effects on the...target system and reduce collateral damage. At high levels of electro- magnetic fields , permanent and catastrophic damage to circuitry, power lines

Performances of a HGCDTE APD based direct detection lidar at 2 μm. Application to dial measurements

NASA Astrophysics Data System (ADS)

Gibert, Fabien; Dumas, Arnaud; Rothman, Johan; Edouart, Dimitri; Cénac, Claire; Pellegrino, Jessica

2018-04-01

A lidar receiver with a direct detection chain adapted to a HgCdTe APD based detector with electric cooling is associated to a 2.05 μm Ho :YLF pulsed dual wavelength single mode transmitter to provide the first atmospheric lidar measurements using this technology. Experiments confirm the outstanding sensitivity of the detector and hightligth its huge potential for DIAL measurements of trace gas (CO2 and H2O) in this spectral domain. Performances of coherent vs direct detection at 2.05 μm is assessed.

IEEE New Jersey Coast Section. Centennial Journal.

DTIC Science & Technology

1984-03-09

to meet any current needs. The IRE has carefully avoided such measures as would lead to its grounding on the shoals of disaster which often lie in the...compatriot members. Also avoided was the develop- ment of insufficient interest resulting from the diverse activities of individual members of the... result of such advances, the benefits to education, whereas today we can dial directly from New York to Tokyo as medicine, business, and science of a

High Repetition Rate Pulsed 2-Micron Laser Transmitter for Coherent CO2 DIAL Measurement

NASA Technical Reports Server (NTRS)

Singh, Uprendra N.; Bai, Yingxin; Yu, Jirong; Petros, Mulugeta; Petzar, Paul J.; Trieu, Bo C.; Lee, Hyung

2009-01-01

A high repetition rate, highly efficient, Q-switched 2-micron laser system as the transmitter of a coherent differential absorption lidar for CO2 measurement has been developed at NASA Langley Research Center. Such a laser transmitter is a master-slave laser system. The master laser operates in a single frequency, either on-line or off-line of a selected CO2 absorption line. The slave laser is a Q-switched ring-cavity Ho:YLF laser which is pumped by a Tm:fiber laser. The repetition rate can be adjusted from a few hundred Hz to 10 kHz. The injection seeding success rate is from 99.4% to 99.95%. For 1 kHz operation, the output pulse energy is 5.5mJ with the pulse length of approximately 50 ns. The optical-to-optical efficiency is 39% when the pump power is 14.5W. The measured standard deviation of the laser frequency jitter is about 3 MHz.

Measuring response to a cancer information telephone facility: Can-Dial.

PubMed Central

Wilkinson, G S; Mirand, E A; Graham, S

1976-01-01

In an attempt to meet the need for increasing public knowledge about cancer, a system providing free information by telephone has been developed. The system is comprised of 36 pre-recorded taped lectures containing information about various aspects of cancer. Interested individuals call a toll-free number, indicate a topic of interest, and listen to the pre-recorded lecture over the phone. An operator handles incoming calls and obtains information from callers used in evaluating the program. During the first year of operation, over 30,000 calls were processed. Topics most frequently requested included those concerning smoking, breast and cervical cancer, and general information. Female response exceeded male response in all age categories. Older people responded less frequently than younger. Urban utilization greatly exceeded suburban and rural utilization. Considerable fluctuation in response related to promotional activities was found. Printed advertisements elicited far greater response than radio and television. Promotional efforts in an experimental group of low-utilizing townships greatly increased utilization while no change was observed in a control group. PMID:1267080

Temporal correlation measurements of pulsed dual CO2 lidar returns. [for atmospheric pollution detection

NASA Technical Reports Server (NTRS)

Menyuk, N.; Killinger, D. K.

1981-01-01

A pulsed dual-laser direct-detection differential-absorption lidar DIAL system, operating near 10.6 microns, is used to measure the temporal correlation and statistical properties of backscattered returns from specular and diffuse topographic targets. Results show that atmospheric-turbulence fluctuations can effectively be frozen for pulse separation times on the order of 1-3 msec or less. The diffuse target returns, however, yielded a much lower correlation than that obtained with the specular targets; this being due to uncorrelated system noise effects and different statistics for the two types of target returns.

Accuracy, reproducibility, and uncertainty analysis of thyroid-probe-based activity measurements for determination of dose calibrator settings.

PubMed

Esquinas, Pedro L; Tanguay, Jesse; Gonzalez, Marjorie; Vuckovic, Milan; Rodríguez-Rodríguez, Cristina; Häfeli, Urs O; Celler, Anna

2016-12-01

In the nuclear medicine department, the activity of radiopharmaceuticals is measured using dose calibrators (DCs) prior to patient injection. The DC consists of an ionization chamber that measures current generated by ionizing radiation (emitted from the radiotracer). In order to obtain an activity reading, the current is converted into units of activity by applying an appropriate calibration factor (also referred to as DC dial setting). Accurate determination of DC dial settings is crucial to ensure that patients receive the appropriate dose in diagnostic scans or radionuclide therapies. The goals of this study were (1) to describe a practical method to experimentally determine dose calibrator settings using a thyroid-probe (TP) and (2) to investigate the accuracy, reproducibility, and uncertainties of the method. As an illustration, the TP method was applied to determine 188 Re dial settings for two dose calibrator models: Atomlab 100plus and Capintec CRC-55tR. Using the TP to determine dose calibrator settings involved three measurements. First, the energy-dependent efficiency of the TP was determined from energy spectra measurements of two calibration sources ( 152 Eu and 22 Na). Second, the gamma emissions from the investigated isotope ( 188 Re) were measured using the TP and its activity was determined using γ-ray spectroscopy methods. Ambient background, scatter, and source-geometry corrections were applied during the efficiency and activity determination steps. Third, the TP-based 188 Re activity was used to determine the dose calibrator settings following the calibration curve method [B. E. Zimmerman et al., J. Nucl. Med. 40, 1508-1516 (1999)]. The interobserver reproducibility of TP measurements was determined by the coefficient of variation (COV) and uncertainties associated to each step of the measuring process were estimated. The accuracy of activity measurements using the proposed method was evaluated by comparing the TP activity estimates of 99m Tc, 188 Re, 131 I, and 57 Co samples to high purity Ge (HPGe) γ-ray spectroscopy measurements. The experimental 188 Re dial settings determined with the TP were 76.5 ± 4.8 and 646 ± 43 for Atomlab 100plus and Capintec CRC-55tR, respectively. In the case of Atomlab 100plus, the TP-based dial settings improved the accuracy of 188 Re activity measurements (confirmed by HPGe measurements) as compared to manufacturer-recommended settings. For Capintec CRC-55tR, the TP-based settings were in agreement with previous results [B. E. Zimmerman et al., J. Nucl. Med. 40, 1508-1516 (1999)] which demonstrated that manufacturer-recommended settings overestimate 188 Re activity by more than 20%. The largest source of uncertainty in the experimentally determined dial settings was due to the application of a geometry correction factor, followed by the uncertainty of the scatter-corrected photopeak counts and the uncertainty of the TP efficiency calibration experiment. When using the most intense photopeak of the sample's emissions, the TP method yielded accurate (within 5% errors) and reproducible (COV = 2%) measurements of sample's activity. The relative uncertainties associated with such measurements ranged from 6% to 8% (expanded uncertainty at 95% confidence interval, k = 2). Accurate determination/verification of dose calibrator dial settings can be performed using a thyroid-probe in the nuclear medicine department.

Progress of 2-micron Detectors for Application to Lidar Remote Sensing

NASA Technical Reports Server (NTRS)

Abedin, M. N.; Refaat, Tamer F.; Ismail, Syed; Koch, Grady; Singh, Upendra N.

2008-01-01

AlGaAsSb/InGaAsSb heterojunction phototransistors were developed at Astropower, Inc under Laser Risk Reduction Program (LRRP) for operation in the 2-micron region. These phototransistors were optimized for 2-micron detection and have high quantum efficiency (>60%), high gain (>10(exp 3)) and low noise-equivalent- power (<5x10(exp -14) W/Hz), while operating at low bias voltage. One of these phototransistors was tested in lidar mode using the 2-micron CO2 Differential Absorption Lidar (DIAL) system currently under development under the Instrument Incubator Program (IIP) at NASA Langley. Lidar measurements included detecting atmospheric structures consisting of thin clouds in the mid-altitude and near-field boundary layer. These test results are very promising for the application of phototransistors for the two-micron lidar remote sensing. In addition, HgCdTe avalanche photodiodes (APD) acquired from Raytheon were used in atmospheric testing at 2-microns. A discussion of these measurements is also presented in this paper.

The 2nd phase of the LEANDRE program: Water-vapor DIAL measurement

NASA Technical Reports Server (NTRS)

Quaglia, P.; Bruneau, D.; Pelon, J.

1992-01-01

As a follow-on of the backscattered lidar, a differential absorption lidar (LEANDRE 2) is now being developed as part of the LEANDRE program for airborne meteorological studies. The primary measurement objective of LEANDRE 2 is water vapor. Pressure and temperature measurements are aimed at a second stage. The goals are to obtain a horizontal resolution of a few hundred meters for a vertical resolution of less than a hundred meters, with an absolute accuracy of 10 percent for humidity measurement. As compatibility is an important feature between the 2 first phases of LEANDRE, most of the LEANDRE 1 sub-system will be used and adapted for LEANDRE 2. For example, detection electronics, central computer, detectors and telescope will be the same. However, important modifications have to be done on the laser source, and spectral control has to be added. Most of the work is thus devoted to those developments, and the status is presented here.

Functional Evaluation of the Reusable JuniorSTAR® Half-Unit Insulin Pen.

PubMed

Klonoff, David; Nayberg, Irina; Rabbone, Ivana; Domenger, Catherine; Stauder, Udo; Oualali, Hamid; Danne, Thomas

2015-05-01

The functional performance of the JuniorSTAR(®) (Sanofi, Paris, France) half-unit insulin pen was evaluated through a series of specific objective tests to assess the dose accuracy, pen weight, injection force, and dialing torque. Pens (n = 60) were tested under standard atmospheric conditions with 3 different types of insulins manufactured by Sanofi (insulin glargine, insulin glulisine, and biphasic insulin isophane). The dose accuracy was tested according to the ISO 11608-1:2012 standards. Injection doses of 0.010, 0.155, and 0.300 ml were evaluated. For mean weight evaluation, the pens without the cartridge were weighed on precision balances. The injection force was measured using a texture analyzer and the dialing torque was measured using a torque meter. JuniorSTAR met the ISO 11608-1:2012 criteria for dose accuracy as all the delivered doses were within the predefined limits for all types of insulin tested. The mean weight of the JuniorSTAR pen was 33.4 g (SD = 0.075). The mean injection force was 6.0 N (SD = 0.8), 4.3 N (SD = 0.4), and 5.1 N (SD = 0.6) for insulin glargine, insulin glulisine, and biphasic insulin isophane, respectively. The mean dialing torque was 5.09 Ncm (SD = 0.29) and 5.88 Ncm (SD = 0.53) for setting and correcting a dose, respectively. Together with results from a previously reported usability survey, these results show that the JuniorSTAR reusable, half-unit pen is a lightweight and accurate device for insulin delivery with a dialing torque and injection force suitable for young people with type 1 diabetes. © 2015 Diabetes Technology Society.

Functional Evaluation of the Reusable JuniorSTAR® Half-Unit Insulin Pen

PubMed Central

Klonoff, David; Nayberg, Irina; Rabbone, Ivana; Domenger, Catherine; Stauder, Udo; Oualali, Hamid; Danne, Thomas

2015-01-01

Background: The functional performance of the JuniorSTAR® (Sanofi, Paris, France) half-unit insulin pen was evaluated through a series of specific objective tests to assess the dose accuracy, pen weight, injection force, and dialing torque. Method: Pens (n = 60) were tested under standard atmospheric conditions with 3 different types of insulins manufactured by Sanofi (insulin glargine, insulin glulisine, and biphasic insulin isophane). The dose accuracy was tested according to the ISO 11608-1:2012 standards. Injection doses of 0.010, 0.155, and 0.300 ml were evaluated. For mean weight evaluation, the pens without the cartridge were weighed on precision balances. The injection force was measured using a texture analyzer and the dialing torque was measured using a torque meter. Results: JuniorSTAR met the ISO 11608-1:2012 criteria for dose accuracy as all the delivered doses were within the predefined limits for all types of insulin tested. The mean weight of the JuniorSTAR pen was 33.4 g (SD = 0.075). The mean injection force was 6.0 N (SD = 0.8), 4.3 N (SD = 0.4), and 5.1 N (SD = 0.6) for insulin glargine, insulin glulisine, and biphasic insulin isophane, respectively. The mean dialing torque was 5.09 Ncm (SD = 0.29) and 5.88 Ncm (SD = 0.53) for setting and correcting a dose, respectively. Conclusions: Together with results from a previously reported usability survey, these results show that the JuniorSTAR reusable, half-unit pen is a lightweight and accurate device for insulin delivery with a dialing torque and injection force suitable for young people with type 1 diabetes. PMID:25633967

Ozone and aerosol distributions measured by airborne lidar during the 1988 Arctic Boundary Layer Experiment

NASA Technical Reports Server (NTRS)

Browell, Edward V.; Butler, Carolyn F.; Kooi, Susan A.

1991-01-01

Consideration is given to O3 and aerosol distributions measured from an aircraft using a DIAL system in order to study the sources and sinks of gases and aerosols over the tundra regions of Alaska during summer 1988. The tropospheric O3 budget over the Arctic was found to be strongly influenced by stratospheric intrusions. Regions of low aerosol scattering and enhanced O3 mixing ratios were usually correlated with descending air from the upper troposphere or lower stratosphere.

High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing (HPC) Environment: Voice Call Analysis

DTIC Science & Technology

2015-09-01

Gateway 2 4. Voice Packet Flow: SIP , Session Description Protocol (SDP), and RTP 3 5. Voice Data Analysis 5 6. Call Analysis 6 7. Call Metrics 6...analysis processing is designed for a general VoIP system architecture based on Session Initiation Protocol ( SIP ) for negotiating call sessions and...employs Skinny Client Control Protocol for network communication between the phone and the local CallManager (e.g., for each dialed digit), SIP

Development of tunable high pressure CO2 laser for lidar measurements of pollutants and wind velocities

NASA Technical Reports Server (NTRS)

Levine, J. S.; Guerra, M.; Javan, A.

1980-01-01

The problem of laser energy extraction at a tunable monochromatic frequency from an energetic high pressure CO2 pulsed laser plasma, for application to remote sensing of atmospheric pollutants by Differential Absorption Lidar (DIAL) and of wind velocities by Doppler Lidar, was investigated. The energy extraction principle analyzed is based on transient injection locking (TIL) at a tunable frequency. Several critical experiments for high gain power amplification by TIL are presented.

Cable-Porn and Dial-A-Porn Control Act. Hearing before the Subcommittee on Criminal Law of the Committee on the Judiciary. United States Senate, Ninety-Ninth Congress, First Session on S. 1090. A Bill to Amend Section 1464 of Title 18, United States Code, Relating to Broadcasting Obscene Language, and for Other Purposes (July 31, 1985).

ERIC Educational Resources Information Center

Congress of the U.S., Washington, DC. Senate Committee on the Judiciary.

A Senate hearing on the cable porn and dial-a-porn control bill is presented in this document. Opening statements by Senators Jeremiah Denton, Arlen Specter, and Jesse Helms discuss the need for this bill and its content. The text of the bill itself is included. Jack D. Smith, General Counsel of the Federal Communications Commission (FCC)…

Characterising Radon Emanations from Radium-Dial Watches

NASA Astrophysics Data System (ADS)

Crockett, Robin; Gillmore, Gavin

2013-04-01

Research during the latter half of 2011 has indicated that in addition to the hazard arising from the radium content of radium-dial watches, significant radon concentrations that exceed the UK Domestic and Workplace Action Levels of 200 Bq/m3 and 400 Bq/m3, respectively, can arise from watches stored in the built environment (1). In an extension to that earlier research, the radon emanations from the watches are being investigated in order to evaluate the radon hazard and the effective radium content of the watches. These radon measurements are made by placing the watches in a sealed chamber in a closed loop with a Durridge RAD7. We report here preliminary results from this ongoing investigation which suggest that radon emanation is not necessarily a straightforward function of radium content, as anticipated, but also depends on chamber temperature and humidity impacting upon watch-dependent factors such as design, construction, materials and wear-and-tear. Reference. 1. Gillmore G K, Crockett R G M, Denman A R, Flowers A, Harris R; Radium dial watches, a potentially hazardous legacy? Environment International. 45, 91-98. 2012. doi:10.1016/j.envint.2012.03.013.

Progress on High-Energy 2-micron Solid State Laser for NASA Space-Based Wind and Carbon Dioxide Measurements

NASA Technical Reports Server (NTRS)

Singh, Upendra N.

2011-01-01

Sustained research efforts at NASA Langley Research Center during last fifteen years have resulted in significant advancement of a 2-micron diode-pumped, solid-state laser transmitter for wind and carbon dioxide measurements from ground, air and space-borne platforms. Solid-state 2-micron laser is a key subsystem for a coherent Doppler lidar that measures the horizontal and vertical wind velocities with high precision and resolution. The same laser, after a few modifications, can also be used in a Differential Absorption Lidar system for measuring atmospheric CO2 concentration profiles. Researchers at NASA Langley Research Center have developed a compact, flight capable, high energy, injection seeded, 2-micron laser transmitter for ground and airborne wind and carbon dioxide measurements. It is capable of producing 250 mJ at 10 Hz by an oscillator and one amplifier. This compact laser transmitter was integrated into a mobile trailer based coherent Doppler wind and CO2 DIAL system and was deployed during field measurement campaigns. This paper will give an overview of 2-micron solid-state laser technology development and discuss results from recent ground-based field measurements.

Air-Flow-Driven Triboelectric Nanogenerators for Self-Powered Real-Time Respiratory Monitoring.

PubMed

Wang, Meng; Zhang, Jiahao; Tang, Yingjie; Li, Jun; Zhang, Baosen; Liang, Erjun; Mao, Yanchao; Wang, Xudong

2018-06-04

Respiration is one of the most important vital signs of humans, and respiratory monitoring plays an important role in physical health management. A low-cost and convenient real-time respiratory monitoring system is extremely desirable. In this work, we demonstrated an air-flow-driven triboelectric nanogenerator (TENG) for self-powered real-time respiratory monitoring by converting mechanical energy of human respiration into electric output signals. The operation of the TENG was based on the air-flow-driven vibration of a flexible nanostructured polytetrafluoroethylene (n-PTFE) thin film in an acrylic tube. This TENG can generate distinct real-time electric signals when exposed to the air flow from different breath behaviors. It was also found that the accumulative charge transferred in breath sensing corresponds well to the total volume of air exchanged during the respiration process. Based on this TENG device, an intelligent wireless respiratory monitoring and alert system was further developed, which used the TENG signal to directly trigger a wireless alarm or dial a cell phone to provide timely alerts in response to breath behavior changes. This research offers a promising solution for developing self-powered real-time respiratory monitoring devices.

Characterization of Advanced Avalanche Photodiodes for Water Vapor Lidar Receivers

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Halama, Gary E.; DeYoung, Russell J.

2000-01-01

Development of advanced differential absorption lidar (DIAL) receivers is very important to increase the accuracy of atmospheric water vapor measurements. A major component of such receivers is the optical detector. In the near-infrared wavelength range avalanche photodiodes (APD's) are the best choice for higher signal-to-noise ratio, where there are many water vapor absorption lines. In this study, characterization experiments were performed to evaluate a group of silicon-based APD's. The APD's have different structures representative of different manufacturers. The experiments include setups to calibrate these devices, as well as characterization of the effects of voltage bias and temperature on the responsivity, surface scans, noise measurements, and frequency response measurements. For each experiment, the setup, procedure, data analysis, and results are given and discussed. This research was done to choose a suitable APD detector for the development of an advanced atmospheric water vapor differential absorption lidar detection system operating either at 720, 820, or 940 nm. The results point out the benefits of using the super low ionization ratio (SLIK) structure APD for its lower noise-equivalent power, which was found to be on the order of 2 to 4 fW/Hz(sup (1/2)), with an appropriate optical system and electronics. The water vapor detection systems signal-to-noise ratio will increase by a factor of 10.

Novel solid state lasers for Lidar applications at 2 μm

NASA Astrophysics Data System (ADS)

Della Valle, G.; Galzerano, G.; Toncelli, A.; Tonelli, M.; Laporta, P.

2005-09-01

A review on the results achieved by our group in the development of novel solid-state lasers for Lidar applications at 2 μm is presented. These lasers, based on fluoride crystals (YLF4, BaY2F8, and KYF4) doped with Tm and Ho ions, are characterized by high-efficiency and wide wavelength tunability around 2 μm. Single crystals of LiYF4, BaY2F8, and KYF4 codoped with the same Tm3+ and Ho3+ concentrations were successfully grown by the Czochralski method. The full spectroscopic characterization of the different laser crystals and the comparison between the laser performance are presented. Continuous wave operation was efficiently demonstrated by means of a CW diode-pumping. These oscillators find interesting applications in the field of remote sensing (Lidar and Dial systems) as well as in high-resolution molecular spectroscopy, frequency metrology, and biomedical applications.

AWAS: A dynamic work scheduling system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Y.; Hao, J.; Kocur, G.

1994-12-31

The Automated Work Administration System (AWAS) is an automated scheduling system developed at GTE. A typical work center has 1000 employees and processes 4000 jobs each day. Jobs are geographically distributed within the service area of the work center, require different skills, and have to be done within specified time windows. Each job can take anywhere from 12 minutes to several hours to complete. Each employee can have his/her individual schedule, skill, or working area. The jobs can enter and leave the system at any time The employees dial up to the system to request for their next job atmore » the beginning of a day or after a job is done. The system is able to respond to the changes dynamically and produce close to optimum solutions at real time. We formulate the real world problem as a minimum cost network flow problem. Both employees and jobs are formulated as nodes. Relationship between jobs and employees are formulated as arcs, and working hours contributed by employees and consumed by jobs are formulated as flow. The goal is to minimize missed commitments. We solve the problem with the successive shortest path algorithm. Combined with pre-processing and post-processing, the system produces reasonable outputs and the response time is very good.« less

Optimization of the GSFC TROPOZ DIAL retrieval using synthetic lidar returns and ozonesondes - Part 1: Algorithm validation

NASA Astrophysics Data System (ADS)

Sullivan, J. T.; McGee, T. J.; Leblanc, T.; Sumnicht, G. K.; Twigg, L. W.

2015-04-01

The main purpose of the NASA Goddard Space Flight Center TROPospheric OZone DIfferential Absorption Lidar (GSFC TROPOZ DIAL) is to measure the vertical distribution of tropospheric ozone for science investigations. Because of the important health and climate impacts of tropospheric ozone, it is imperative to quantify background photochemical and aloft ozone concentrations, especially during air quality episodes. To better characterize tropospheric ozone, the Tropospheric Ozone Lidar Network (TOLNet) has recently been developed, which currently consists of five different ozone DIAL instruments, including the TROPOZ. This paper addresses the necessary procedures to validate the TROPOZ retrieval algorithm and develops a primary standard for retrieval consistency and optimization within TOLNet. This paper is focused on ensuring the TROPOZ and future TOLNet algorithms are properly quantifying ozone concentrations and the following paper will focus on defining a systematic uncertainty analysis standard for all TOLNet instruments. Although this paper is used to optimize the TROPOZ retrieval, the methodology presented may be extended and applied to most other DIAL instruments, even if the atmospheric product of interest is not tropospheric ozone (e.g. temperature or water vapor). The analysis begins by computing synthetic lidar returns from actual TROPOZ lidar return signals in combination with a known ozone profile. From these synthetic signals, it is possible to explicitly determine retrieval algorithm biases from the known profile, thereby identifying any areas that may need refinement for a new operational version of the TROPOZ retrieval algorithm. A new vertical resolution scheme is presented, which was upgraded from a constant vertical resolution to a variable vertical resolution, in order to yield a statistical uncertainty of <10%. The optimized vertical resolution scheme retains the ability to resolve fluctuations in the known ozone profile and now allows near field signals to be more appropriately smoothed. With these revisions, the optimized TROPOZ retrieval algorithm (TROPOZopt) has been effective in retrieving nearly 200 m lower to the surface. Also, as compared to the previous version of the retrieval, the TROPOZopt has reduced the mean profile bias by 3.5% and large reductions in bias (near 15 %) were apparent above 4.5 km. Finally, to ensure the TROPOZopt retrieval algorithm is robust enough to handle actual lidar return signals, a comparison is shown between four nearby ozonesonde measurements. The ozonesondes agree well with the retrieval and are mostly within the TROPOZopt retrieval uncertainty bars (which implies that this exercise was quite successful). A final mean percent difference plot is shown between the TROPOZopt and ozonesondes, which indicates that the new operational retrieval is mostly within 10% of the ozonesonde measurement and no systematic biases are present. The authors believe that this analysis has significantly added to the confidence in the TROPOZ instrument and provides a standard for current and future TOLNet algorithms.

Deflected mirage mediation: a phenomenological framework for generalized supersymmetry breaking.

PubMed

Everett, Lisa L; Kim, Ian-Woo; Ouyang, Peter; Zurek, Kathryn M

2008-09-05

We present a general phenomenological framework for dialing between gravity mediation, gauge mediation, and anomaly mediation. The approach is motivated from recent developments in moduli stabilization, which suggest that gravity mediated terms can be effectively loop suppressed and thus comparable to gauge and anomaly mediated terms. The gauginos exhibit a mirage unification behavior at a "deflected" scale, and gluinos are often the lightest colored sparticles. The approach provides a rich setting in which to explore generalized supersymmetry breaking at the CERN Large Hadron Collider.

Micro-pulse, differential absorption lidar (dial) network for measuring the spatial and temporal distribution of water vapor in the lower atmosphere

NASA Astrophysics Data System (ADS)

Spuler, Scott; Repasky, Kevin; Hayman, Matt; Nehrir, Amin

2018-04-01

The National Center for Atmospheric Research (NCAR) and Montana State Univeristy (MSU) are developing a test network of five micro-pulse differential absorption lidars to continuously measure high-vertical-resolution water vapor in the lower atmosphere. The instruments are accurate, yet low-cost; operate unattended, and eye-safe - all key features to enable the larger network needed to characterize atmospheric moisture variability which influences important processes related to weather and climate.

Advancing Our Understanding of the Etiologies and Mutational Landscapes of Basal-Like, Luminal A, and Luminal B Breast Cancers

DTIC Science & Technology

2013-10-01

random digit dialing (RDD) interviewers. To support this and on-going training, Ms. Taylor will develop a question by question (QxQ)specification...from each other. All Page 9 triple-negative cases will be evaluated for EGFR and cytokeratin 5/6 using IHC so basal-like cases can be identified...by PCR amplification of the identified exons in tumor and matched normal DNA followed by PCR cleanup using Agencourt Ampure XP reagents and then

The Charlotte (TM) intra-vehicular robot

NASA Technical Reports Server (NTRS)

Swaim, Patrick L.; Thompson, Clark J.; Campbell, Perry D.

1994-01-01

NASA has identified telerobotics and telescience as essential technologies to reduce the crew extra-vehicular activity (EVA) and intra-vehicular activity (IVA) workloads. Under this project, we are developing and flight testing a novel IVA robot to relieve the crew of tedious and routine tasks. Through ground telerobotic control of this robot, we will enable ground researchers to routinely interact with experiments in space. Our approach is to develop an IVA robot system incrementally by employing a series of flight tests with increasing complexity. This approach has the advantages of providing an early IVA capability that can assist the crew, demonstrate capabilities that ground researchers can be confident of in planning for future experiments, and allow incremental refinement of system capabilities and insertion of new technology. In parallel with this approach to flight testing, we seek to establish ground test beds, in which the requirements of payload experimenters can be further investigated. In 1993 we reviewed manifested SpaceHab experiments and defined IVA robot requirements to assist in their operation. We also examined previous IVA robot designs and assessed them against flight requirements. We rejected previous design concepts on the basis of threat to crew safety, operability, and maintainability. Based on this insight, we developed an entirely new concept for IVA robotics, the CHARLOTTE robot system. Ground based testing of a prototype version of the system has already proven its ability to perform most common tasks demanded of the crew, including operation of switches, buttons, knobs, dials, and performing video surveys of experiments and switch panels.

Antimicrobial efficacy of soap and water hand washing versus an alcohol-based hand cleanser.

PubMed

Holton, Ronald H; Huber, Michaell A; Terezhalmy, Geza T

2009-12-01

The emergence of alcohol-based hand cleansers may represent an alternative to soap and water in the clinical dental setting. In this study, the antimicrobial efficacy of traditional hand washing vs. a unique alcohol-based hand cleanser with persistence was evaluated. Two experienced dentists participated over a 10-day period. On days 1-5, each clinician used an antibacterial liquid soap (Dial, Dial Corporation, Scottsdale, AZ). Days 6-10, an alcohol-based hand cleanser (Triseptin Water Optional, Healthpoint Surgical, Fort Worth, TX) was used. Sampling was by modified glove juice technique. The results indicate that the alcohol-based hand cleanser dramatically outperforms the traditional hand washing agent in the general dental setting.

Weather and climate needs for Lidar observations from space and concepts for their realization. [wind, temperature, moisture, and pressure data needs

NASA Technical Reports Server (NTRS)

Atlas, D.; Korb, C. L.

1980-01-01

The spectrum of weather and climate needs for Lidar observations from space is discussed with emphasis on the requirements for wind, temperature, moisture, and pressure data. It is shown that winds are required to realistically depict all atmospheric scales in the tropics and the smaller scales at higher latitudes, where both temperature and wind profiles are necessary. The need for means to estimate air-sea exchanges of sensible and latent heat also is noted. A concept for achieving this through a combination of Lidar cloud top heights and IR cloud top temperatures of cloud streets formed during cold air outbreaks over the warmer ocean is outlined. Recent theoretical feasibility studies concerning the profiling of temperatures, pressure, and humidity by differential absorption Lidar (DIAL) from space and expected accuracies are reviewed. An alternative approach to Doppler Lidar wind measurements also is presented. The concept involves the measurement of the displacement of the aerosol backscatter pattern, at constant heights, between two successive scans of the same area, one ahead of the spacecraft and the other behind it a few minutes later. Finally, an integrated space Lidar system capable of measuring temperature, pressure, humidity, and winds which combines the DIAL methods with the aerosol pattern displacement concept is described.

Reviews Book: At Home: A Short History of Private Life Book: The Story of Mathematics Book: Time Travel: A Writer's Guide to the Real Science of Plausible Time Travel Equipment: Rotational Inertial Wands DVD: Planets Book: The Fallacy of Fine-Tuning Equipment: Scale with Dial Equipment: Infrared Thermometers Book: 300 Science and History Projects Book: The Nature of Light and Colour in the Open Air Equipment: Red Tide Spectrometer Web Watch

NASA Astrophysics Data System (ADS)

2011-09-01

WE RECOMMEND The Story of Mathematics Book shows the link between maths and physics Time Travel: A Writer's Guide to the Real Science of Plausible Time Travel Book explains how to write good time-travelling science fiction Rotational Inertial Wands Wands can help explore the theory of inertia Infrared Thermometers Kit measures temperature differences Red Tide Spectrometer Spectrometer gives colour spectra WORTH A LOOK At Home: A Short History of Private Life Bryson explores the history of home life The Fallacy of Fine-Tuning Book wades into the science/religion debate Scale with Dial Cheap scales can be turned into Newton measuring scales 300 Science History Projects Fun science projects for kids to enjoy The Nature of Light and Colour in the Open Air Text looks at fascinating optical effects HANDLE WITH CARE Planets DVD takes a trip through the solar system WEB WATCH Websites offer representations of nuclear chain reactions

Fresnel Lens Characterization for Potential Use in an Unpiloted Atmospheric Vehicle DIAL Receiver System

NASA Technical Reports Server (NTRS)

Fastig, Shlomo; Deoung, Russell J.

1998-01-01

Acrylic plastic Fresnel lenses are very light and can have large diameters. Such lenses could be used in lidar telescope receivers if the focal spot is not too large or distorted. This research effort characterizes the focal spot diameter produced by a Fresnel lens with a diameter of 30.5 cm (12 in.). It was found that the focal spot diameter varied from 1.2 mm at 750 nm to 1.6 mm at 910 nm. The focal spot was irregular and not easily described by a Gaussian profile.

Mixed garnet laser for a water vapour DIAL

NASA Astrophysics Data System (ADS)

Treichel, Rainer; Strohmaier, Stephan; Nikolov, Susanne; Eichler, Hans-Joachim; Murphy, Eamonn

2017-11-01

For the water vapour DIAL "WALES" the wavelength regions around 935 nm, 942 nm and 944 nm have been identified as the most suitable wavelength ranges. These wavelengths can be obtained using opticalparametric-oscillators (OPOs), stimulated Raman shifters and the Ti-Sapphire laser but none of these systems could deliver all the needed parameters like beam quality, efficiency, pulse length and energy yet. Also these systems are comparably big and heavy making them less suitable for a satellite based application. A fourth possibility to achieve these wavelength ranges is to shift the quasi-3-level laser lines (938 nm and 946 nm) of the Nd:YAG laser by replacing aluminium and yttrium by other rare earth elements. Changes of the host lattice characteristics lead to a shift of the upper and lower laser levels. These modified crystals are summarized under the name of "Mixed Garnet" crystals. Only the Mixed Garnet lasers can be pumped directly with diode laser and use a direct approach to generate the required laser pulses without frequency conversion. Therefore no additional non-linear crystals or special pump lasers are needed and a higher electric to optical efficiency is expected as well as single frequency operation using spectral tuning elements like etalons. In a first phase such mixed garnet crystals had been grown and characterised. The outcome was the selection of the gadolinium-scandium garnet for the most suitable laser crystal. During a second phase the complete laser system with output energy about 18 mJ in single 20 ns pulses and up to 8 mJ in free running mode with a combined pulse width of 250 μs at 942 nm have been demonstrated. The results of the first laser operation and the achieved performance parameter are reported.

Deriving the real-ear SPL of audiometric data using the "coupler to dial difference" and the "real ear to coupler difference".

PubMed

Munro, K J; Davis, J

2003-04-01

The purpose of the study was to compare the measured real-ear sound pressure level (SPL) of audiometer output with the derived real-ear SPL obtained by adding the coupler to dial difference (CDD) and real-ear to coupler difference (RECD) to the audiometer dial reading. The real-ear SPL and RECD were measured in one ear of 16 normally hearing subjects using a probe-tube microphone. The CDD transform and the RECD transfer function were measured in an HA1 and an HA2 2-cc coupler using an EAR-LINK foam ear-tip or a customized earmold. The RECD transfer function was measured using the EARTone ER 3A and the Audioscan RE770 insert earphone. The procedures were very reliable with mean differences on retest of less than 1 dB. The mean difference between the measured and derived real-ear SPL was generally less than 1 dB and rarely exceeded 3 dB in any subject. The CDD measured for an individual audiometer and the RECD measured for an individual ear can be used to derive a valid estimate of real-ear SPL when it has not been possible to measure this directly.

Control of Thermal Convection in Layered Fluids Using Magnetic fields

NASA Technical Reports Server (NTRS)

Ramachandran, N.; Leslie, F. W.

2003-01-01

Immiscible fluid layers are found in a host of applications ranging from materials processing, for example the use of encapsulants in float zone crystal growth technique and a buffer layer in industrial Czochralski growth of crystals to prevent Marangoni convection, to heat transfer phenomena in day-to-day processes like the presence of air pockets in heat exchangers. In the microgravity and space processing realm, the exploration of other planets requires the development of enabling technologies in several fronts. The reduction in the gravity level poses unique challenges for fluid handling and heat transfer applications. The present work investigates the efficacy of controlling thermal convective flow using magnetic fluids and magnetic fields. The setup is a two-layer immiscible liquids system with one of the fluids being a diluted ferrofluid (super paramagnetic nano particles dispersed in carrier fluid). Using an external magnetic field one can essentially dial in a volumetric force - gravity level, on the magnetic fluid and thereby affect the system thermo-fluid behavior. The paper will describe the experimental and numerical modeling approach to the problem and discuss results obtained to date.

Development of ground-based lidars for measuring H2O and O3 profiles in the troposphere

NASA Astrophysics Data System (ADS)

Sakai, T.; Abo, M.; Pham, L. H. P.; Uchino, O.; Nagai, T.; Izumi, T.; Morino, I.; Ohyama, H.; Nagasawa, C.

2015-12-01

Water vapor is the strongest natural greenhouse gas and a highly variable atmospheric constituent. It plays an important role of the energy transfer and the meteorological phenomena such as evaporation, vapor transport, cloud formation, and rainfall in the troposphere. Ozone is an important air pollutant that at high concentrations impacts on human health and ecosystem including crops and also a greenhouse gas that plays an important role in climate change. Aerosol is an important climate parameter and also one of the largest error sources (causes) in retrieval from solar reflected short wavelength infrared radiances observed with greenhouse gases observing satellites such as the GOSAT and OCO-2. Therefore, we have been developing ground-based differential absorption lidars (DIALs) for measuring the tropospheric water vapor, ozone and aerosols.The water vapor DIAL employs two distributed Bragg reflector (DBR) lasers operating at 829.054 nm for the online wavelength and 829.124 nm for the offline wavelength with tapered semiconductor optical amplifier (TSOA) in a master oscillator power amplifier (MOPA) configuration, and utilizes pseudorandom coded pulse modulation technique.It has started to measure the vertical distribution of lower tropospheric water vapor in order to improve accuracy and lead time of numerical weather prediction of local heavy rainfalls. Well-organized and regularly spaced convective cells of which vertical thickness were 200 m and the periods were 10 minutes were observed in the top of planetary boundary layer at 2.5 km altitude over Tokyo (35.66°N, 139.37°E) on 22 June 2015.The ozone DIAL employs a Nd:YAG laser and a 2 m long Raman cell filled with CO2 gas which generates four Stokes lines (276.2, 287.2, 299.1, and 312.0 nm) of stimulated Raman scattering, and two receiving telescopes with diameters of 49 and 10 cm.It has started to measure the vertical distributions of the tropospheric ozone as well as aerosols and thin cirrus cloud in order to validate GOSAT product. High concentrations of ozone and aerosols were observed below 2 km altitude on 22 March 2015 over Saga (33.24°N, 130.29°E), which could be transported with spherical aerosols and dust particles from Northeast Asia. The observational result of ozone will be compared with a chemistry-climate model.

Tunneling spectra for electrons in the lowest Landau level

NASA Astrophysics Data System (ADS)

Burnell, F. J.; Simon, Steven H.

2010-03-01

The recently developed experimental technique of time dependent capacitance spectroscopy [1] allows for measurements of high-resolution tunneling spectra of 2DEGs in the quantum Hall regime, giving a detailed probe of the single particle spectral function (electron addition and subtraction spectra). These experiments show a number of interesting features including Landau level structure, exchange enhanced Zeeman energy, Coulomb gap physics, effects of fractional quantization, as well as several key features that remain to be explained. While there has been some prior theoretical work[2] towards explaining low energy Coulomb gap features of tunneling spectra found in much earlier tunneling experiments [3], the new experiments[1] have uncovered physics outside of the prior theoretical explanations. Building on a number of these prior theoretical works, we investigate theoretically the expected tunneling spectra for electrons in low Landau levels, including the effects of electron spin and coupling to collective modes. [1] O. E. Dial, R.C. Ashoori, L.N. Pfeiffer, and K.W. West, Nature 448, 176-179 (2007) ; O. E. Dial et al, unpublished. [2] I. Aleiner et al, Phys. Rev. Lett 74 3435; (1994) S. R. E. Yang and A. MacDonald PRL 70 4110 (1993); S. He, P.M. Platzman, and B. I. Halperin, PRL 71 777 (1993). [3] J. P. Eisenstein et al, Phy. Rev. Lett. 69, 3804 (1992).

LOSS OF BLOOD AT OPERATION—A Method for Continuous Measurement

PubMed Central

Borden, Fred W.

1957-01-01

A method for continuous measurement of surgical blood loss has been devised and has been used clinically in some 400 cases. The method combines volumetric measure of the suction loss and gravimetric measure of the sponge loss. The volumetric device automatically deducts the volume of rinse water used and thus measures the amount of blood collected in a metering cylinder. The suction loss scale shows continuously the amount of blood in the metering cylinder. The gravimetric device requires counting sponges into the weighing pan, and turning a dial scale to deduct the initial weight of the sponges. The volume of blood in the sponges is then read directly on the dial scale. Use of the instrument, which is under the supervision of the anesthesiologist, adds about two minutes per hour to the time normally required for counting the sponges; and about three minutes per hour is required for tending the volumetric instrument. In clinical use, knowing constantly the amount of blood loss permits the starting of transfusion before serious deficit develops, and then maintaining the patient's blood volume at a predetermined optimum level. In some 400 cases the continuous measurement of the blood loss served as a reliable guide for carrying out the loss-replacement plan within close limits of accuracy. ImagesFigure 2.p97-a PMID:13446754

Progress of research on water vapor lidar

NASA Technical Reports Server (NTRS)

Wilkerson, Thomas D.; Singh, U. N.

1989-01-01

Research is summarized on applications of stimulated Raman scattering (SRS) of laser light into near infrared wavelengths suitable for atmospheric monitoring. Issues addressed are conversion efficiency, spectral purity, optimization of operating conditions, and amplification techniques. A Raman cell was developed and built for the laboratory program, and is now available to NASA-Langley, either as a design or as a completed cell for laboratory or flight applications. The Raman cell has been approved for flight in NASA's DC-8 aircraft. The self-seeding SRS technique developed here is suggested as an essential improvement for tunable near-IR DIAL applications at wavelengths of order 1 micrometer or greater.

Computer animation of NASTRAN displacements on IRIS 4D-series workstations: CANDI/ANIMATE postprocessing of NASHUA results

NASA Technical Reports Server (NTRS)

Fales, Janine L.

1991-01-01

The capabilities of the postprocessing program CANDI (Color Animation of Nastran DIsplacements) were expanded to accept results from axisymmetric analysis. An auxiliary program, ANIMATE, was developed to allow color display of CANDI output on the IRIS 4D-series workstations. The user can interactively manipulate the graphics display by three-dimensional rotations, translations, and scaling through the use of the keyboard and/or dials box. The user can also specify what portion of the model is displayed. These developments are limited to the display of complex displacements calculated with the NASHUA/NASTRAN procedure for structural acoustics analysis.

Concentrating Radioactivity

ERIC Educational Resources Information Center

Herrmann, Richard A.

1974-01-01

By concentrating radioactivity contained on luminous dials, a teacher can make a high reading source for classroom experiments on radiation. The preparation of the source and its uses are described. (DT)

An Intelligent Terminal for Access to a Medical Database

PubMed Central

Womble, M. E.; Wilson, S. D.; Keiser, H. N.; Tworek, M. L.

1978-01-01

Very powerful data base management systems (DBMS) now exist which allow medical personnel access to patient record data bases. DBMS's make it easy to retrieve either complete or abbreviated records of patients with similar characteristics. In addition, statistics on data base records are immediately accessible. However, the price of this power is a large computer with the inherent problems of access, response time, and reliability. If a general purpose, time-shared computer is used to get this power, the response time to a request can be either rapid or slow, depending upon loading by other users. Furthermore, if the computer is accessed via dial-up telephone lines, there is competition with other users for telephone ports. If either the DBMS or the host machine is replaced, the medical users, who are typically not sophisticated in computer usage, are forced to learn the new system. Microcomputers, because of their low cost and adaptability, lend themselves to a solution of these problems. A microprocessor-based intelligent terminal has been designed and implemented at the USAF School of Aerospace Medicine to provide a transparent interface between the user and his data base. The intelligent terminal system includes multiple microprocessors, floppy disks, a CRT terminal, and a printer. Users interact with the system at the CRT terminal using menu selection (framing). The system translates the menu selection into the query language of the DBMS and handles all actual communication with the DBMS and its host computer, including telephone dialing and sign on procedures, as well as the actual data base query and response. Retrieved information is stored locally for CRT display, hard copy production, and/or permanent retention. Microprocessor-based communication units provide security for sensitive medical data through encryption/decryption algorithms and high reliability error detection transmission schemes. Highly modular software design permits adapation to a different DBMS and/or host computer with only minor localized software changes. Importantly, this portability is completely transparent to system users. Although the terminal system is independent of the host computer and its DBMS, it has been linked to a UNIVAC 1108 computer supporting MRI's SYSTEM 2000 DBMS.

LANL receiver system development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Laubscher, B.; Cooke, B.; Cafferty, M.

1997-08-01

The CALIOPE receiver system development at LANL is the story of two technologies. The first of these technologies consists of off-the-shelf mercury-cadmium-telluride (MCT) detectors and amplifiers. The vendor for this system is Kolmar Technologies. This system was fielded in the Tan Trailer I (TTI) in 1995 and will be referred to in this paper as GEN I. The second system consists of a MCT detector procured from Santa Barbara Research Center (SBRC) and an amplifier designed and built by LANL. This system was fielded in the Tan Trailer II (TTII) system at the NTS tests in 1996 and will bemore » referred to as GEN II. The LANL CALIOPE experimental plan for 1996 was to improve the lidar system by progressing to a higher rep rate laser to perform many shots in a much shorter period of time. In keeping with this plan, the receiver team set a goal of developing a detector system that was background limited for the projected 100 nanosecond (ns) laser pulse. A set of detailed simulations of the DIAL lidar experiment was performed. From these runs, parameters such as optimal detector size, field of view of the receiver system, nominal laser return power, etc. were extracted. With this information, detector physics and amplifier electronic models were developed to obtain the required specifications for each of these components. These derived specs indicated that a substantial improvement over commercially available, off-the-shelf, amplifier and detector technologies would be needed to obtain the goals. To determine if the original GEN I detector was usable, the authors performed tests on a 100 micron square detector at cryogenic temperatures. The results of this test and others convinced them that an advanced detector was required. Eventually, a suitable detector was identified and a number of these single element detectors were procured from SBRC. These single element detectors were witness for the detector arrays built for another DOE project.« less

Remote operation of the Black Knight unmanned ground combat vehicle

NASA Astrophysics Data System (ADS)

Valois, Jean-Sebastien; Herman, Herman; Bares, John; Rice, David P.

2008-04-01

The Black Knight is a 12-ton, C-130 deployable Unmanned Ground Combat Vehicle (UGCV). It was developed to demonstrate how unmanned vehicles can be integrated into a mechanized military force to increase combat capability while protecting Soldiers in a full spectrum of battlefield scenarios. The Black Knight is used in military operational tests that allow Soldiers to develop the necessary techniques, tactics, and procedures to operate a large unmanned vehicle within a mechanized military force. It can be safely controlled by Soldiers from inside a manned fighting vehicle, such as the Bradley Fighting Vehicle. Black Knight control modes include path tracking, guarded teleoperation, and fully autonomous movement. Its state-of-the-art Autonomous Navigation Module (ANM) includes terrain-mapping sensors for route planning, terrain classification, and obstacle avoidance. In guarded teleoperation mode, the ANM data, together with automotive dials and gages, are used to generate video overlays that assist the operator for both day and night driving performance. Remote operation of various sensors also allows Soldiers to perform effective target location and tracking. This document covers Black Knight's system architecture and includes implementation overviews of the various operation modes. We conclude with lessons learned and development goals for the Black Knight UGCV.

Calibration Device Designed for proof ring used in SCC Experiment

NASA Astrophysics Data System (ADS)

Hu, X. Y.; Kang, Z. Y.; Yu, Y. L.

2017-11-01

In this paper, a calibration device for proof ring used in SCC (Stress Corrosion Cracking) experiment was designed. A compact size loading device was developed to replace traditional force standard machine or a long screw nut. The deformation of the proof ring was measured by a CCD (Charge-Coupled Device) during the calibration instead of digital caliper or a dial gauge. The calibration device was verified at laboratory that the precision of force loading is ±0.1% and the precision of deformation measurement is ±0.002mm.

Lidar investigations of ozone in the upper troposphere - lower stratosphere: technique and results of measurements

NASA Astrophysics Data System (ADS)

Romanovskii, Oleg A.; Nevzorov, Alexey A.; Nevzorov, Alexey V.; Kharchenko, Olga V.

2018-04-01

The main aim of the research is to develop the technique for laser remote ozone sensing in the upper troposphere - lower stratosphere by differential absorption method for temperature and aerosol correction and analysis of measurement results. The authors have determined wavelengths, promising to measure ozone profiles in the upper troposphere - lower stratosphere. We present the results of DIAL measurements of the vertical ozone distribution at the Siberian lidar station in Tomsk. The recovered ozone profiles were compared with IASI satellite data and Kruger model.

Association between systemically administered radioisotopes and subsequent malignant disease

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berlin, N.I.; Wasserman, L.R.

1976-02-01

There is a long history recording the association of x radiation and the subsequent development of malignant tumors. For systemically administered isotopes this came into prominence when Martland discovered the association between cancer, particularly of the bone, and ingestion of radioactive isotopes by radium dial painters. This association was amplified by the development of cancer in patients given thorotrast as a contrast medium for diagnostic radiologic examination. Acute leukemia was reported 30 years ago in patients with polycythemia vera treated with $sup 32$P. Acute leukemia also occurs in patients with polycythemia vera treated only with phlebotomy or drugs. A controlledmore » study is now underway to provide a more definite answer to question what is the incidence of acute leukemia in patients with polycythemia vera treated by phlebotomy alone, chlorambucil, or $sup 32$P. $sup 131$I for the treatment of hyperthyroidism probably does not induce cancer, but in the doses used for thyroid cancer there was an increased incidence of neoplasms (12/200 in one study). This was higher than the expected incidence of neoplasms. The doses of radioactive isotopes used currently for diagnostic purposes have not induced cancer, but it is difficult and probably impossible to verify this with absolute certainty. (auth)« less

Development of a survey instrument to measure patient experience of integrated care.

PubMed

Walker, Kara Odom; Stewart, Anita L; Grumbach, Kevin

2016-06-01

Healthcare systems are working to move towards more integrated, patient-centered care. This study describes the development and testing of a multidimensional self-report measure of patients' experiences of integrated care. Random-digit-dial telephone survey in 2012 of 317 adults aged 40 years or older in the San Francisco region who had used healthcare at least twice in the past 12 months. One-time cross-sectional survey; psychometric evaluation to confirm dimensions and create multi-item scales. Survey data were analyzed using VARCLUS and confirmatory factor analysis and internal consistency reliability testing. Scales measuring five domains were confirmed: coordination within and between care teams, navigation (arranging appointments and visits), communication between specialist and primary care doctor, and communication between primary care doctor and specialist. Four of these demonstrated excellent internal consistency reliability. Mean scale scores indicated low levels of integration. These scales measuring integrated care capture meaningful domains of patients' experiences of health care. The low levels of care integration reported by patients in the study sample suggest that these types of measures should be considered in ongoing evaluations of health system performance and improvement. Further research should examine whether differences in patient experience of integrated care are associated with differences in the processes and outcomes of care received.

Lidar Remote Sensing for Industry and Environment Monitoring

NASA Technical Reports Server (NTRS)

Singh, Upendra N. (Editor); Itabe, Toshikazu (Editor); Sugimoto, Nobuo (Editor)

2000-01-01

Contents include the following: 1. Keynote paper: Overview of lidar technology for industrial and environmental monitoring in Japan. 2. lidar technology I: NASA's future active remote sensing mission for earth science. Geometrical detector consideration s in laser sensing application (invited paper). 3. Lidar technology II: High-power femtosecond light strings as novel atmospheric probes (invited paper). Design of a compact high-sensitivity aerosol profiling lidar. 4. Lasers for lidars: High-energy 2 microns laser for multiple lidar applications. New submount requirement of conductively cooled laser diodes for lidar applications. 5. Tropospheric aerosols and clouds I: Lidar monitoring of clouds and aerosols at the facility for atmospheric remote sensing (invited paper). Measurement of asian dust by using multiwavelength lidar. Global monitoring of clouds and aerosols using a network of micropulse lidar systems. 6. Troposphere aerosols and clouds II: Scanning lidar measurements of marine aerosol fields at a coastal site in Hawaii. 7. Tropospheric aerosols and clouds III: Formation of ice cloud from asian dust particles in the upper troposphere. Atmospheric boundary layer observation by ground-based lidar at KMITL, Thailand (13 deg N, 100 deg. E). 8. Boundary layer, urban pollution: Studies of the spatial correlation between urban aerosols and local traffic congestion using a slant angle scanning on the research vessel Mirai. 9. Middle atmosphere: Lidar-observed arctic PSC's over Svalbard (invited paper). Sodium temperature lidar measurements of the mesopause region over Syowa Station. 10. Differential absorption lidar (dIAL) and DOAS: Airborne UV DIAL measurements of ozone and aerosols (invited paper). Measurement of water vapor, surface ozone, and ethylene using differential absorption lidar. 12. Space lidar I: Lightweight lidar telescopes for space applications (invited paper). Coherent lidar development for Doppler wind measurement from the International Space Station. 13. Space lidar II: Using coherent Doppler lidar to estimate river discharge. 14. Poster session: Lidar technology, optics for lidar. Laser for lidar. Middle atmosphere observations. Tropospheric observations (aerosols, clouds). Boundary layer, urban pollution. Differential absorption lidar. Doppler lidar. and Space lidar.

SU-E-P-45: An Analytical Formula for Deriving Mechanical Iso-Center of Rotational Gantry Treatment Unit Rotational Gantry Treatment Unit

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, X; Bues, M

2015-06-15

Purpose: To present an analytical formula for deriving mechanical isocenter (MIC) of a rotational gantry treatment unit. The input data to the formula is obtained by a custom-made device. The formula has been implemented and used in an operational proton therapy facility since 2005. Methods: The custom made device consisted of 3 mutually perpendicular dial indicators and 5 clinometers, to obtain displacement data and gantry angle data simultaneously. During measurement, a steel sphere was affixed to the patient couch, and the device was attached to the snout rotating with the gantry. The displacement data and angle data were obtained simultaneouslymore » at angular increments of less than 1 degree. The analytical formula took the displacement and angle as input and derived the positions of dial indicator tips (DIT) position in room-fixed coordinate system. The formula derivation presupposes trigonometry and 3-dimentional coordinate transformations. Due to the symmetry properties of the defining equations, the DIT position can be solved for analytically without using mathematical approximations. We define the mean of all points in the DIT trajectory as the MIC. The formula was implemented in computer code, which has been employed during acceptance test, commissioning, as well as routine QA practice in an operational proton facility since 2005. Results: It took one minute for the custom-made device to acquire the measurement data for a full gantry rotation. The DIT trajectory and MIS are instantaneously available after the measurement. The MIC Result agrees well with vendor’s Result, which came from a different measurement setup, as well as different data analysis algorithm. Conclusion: An analytical formula for deriving mechanical isocenter was developed and validated. The formula is considered to be absolutely accurate mathematically. Be analyzing measured data of radial displacements as function of gantry angle, the formula calculates the MI position in room coordinate.« less

Command, Control and Communications Capabilities Enabling 21st Century Missions, a Historical Perspective

NASA Technical Reports Server (NTRS)

Waterman, Robert D.; Rice, Herbert D.; Waterman, Susan J.

2010-01-01

Command, Control and Communications (CCC) has evolved through the years from simple switches, dials, analogue hardwire networks and lights to a modern computer based digital network. However there are two closely coupled pillars upon which a CCC system is built. The first, is that technology drives the pace of advancement. The second is that a culture that fosters resistance to change can limit technological advancements in the CCC system. While technology has advanced at a tremendous rate throughout the years, the change in culture has moved slowly. This paper will attempt to show through a historical perspective where specific design decisions for early CCC systems have erroneously evolved into general requirements being imposed on later systems. Finally this paper will provide a glimpse into the future directions envisioned for CCC capabilities that will enable 21st century missions.

Weather and climate needs for lidar observations from space and concepts for their realization

NASA Technical Reports Server (NTRS)

Atlas, D.; Korb, C. L.

1981-01-01

The spectrum of weather and climate needs for lidar observations from space is discussed. This paper focuses mainly on the requirements for winds, temperature, moisture, and pressure. Special emphasis is given to the need for wind observations, and it is shown that winds are required to depict realistically all atmospheric scales in the tropics and the smaller scales at higher latitudes, where both temperature and wind profiles are necessary. The need for means to estimate air-sea exchanges of sensible and latent heat also is noted. Lidar can aid here by measurement of the slope of the boundary layer. Recent theoretical feasibility studies concerning the profiling of temperature, pressure, and humidity by differential absorption lidar (DIAL) from space and expected accuracies are reviewed. Initial ground-based trials provide support for these approaches and also indicate their direct applicability to path-average temperature measurements near the surface. An alternative approach to Doppler lidar wind measurements also is presented. The concept involves the measurement of the displacement of the aerosol backscatter pattern, at constant height, between two successive scans of the same area, one ahead of the spacecraft and the other behind it, a few minutes later. Finally, an integrated space lidar system capable of measuring temperature, pressure, humidity, and winds which combines the DIAL methods with the aerosol pattern displacement concept is described briefly.

Proceedings of the Interservice/Industry Training Equipment Conference (5th) Held at Washington, DC on November 14-16, 1983. Volume 2.

DTIC Science & Technology

1983-11-16

at the Ballistic Missile Division as a Space Systems Project Officer, in between Command and Staff and Air War College tours as a student . • It’s at...sure that the student got used to the real thing. Since instruments in simulators get about six times as many cycles as those in the aircraft themselves...that the student really needed to see was the dial face. The student couldn’t care less whether the guts of the real instrument was behind the aircraft

Implementation of Individual System Qualification (ISQ) in a CBRN Respiratory Protection Program, Part B: Standard Operating Procedures

DTIC Science & Technology

2014-10-01

or V2) on the side that is being tested. f. Plug the threaded hole in the face-form with a wetted finger. g. Gently pump the vacuum bulb enough to...a stop watch for a 45 second count down. 8. Close the bleed valve on the appropriate vacuum squeeze bulb (V1 or V2). Pump the bulb to draw a... vacuum into the mask until the gauge reaches or exceeds the green section of the dial (Figure 6). Generally 2 pumps will be sufficient. If the vacuum will

An Inexpensive Real-Time Interactive Three Dimensional Flight Simulation System.

DTIC Science & Technology

1987-06-01

irh ’.etp. the 4i, n. he Ii~ Pi~op 4’ WV o cl d m od 0 V d 0 i c IV 1 M A,.. wq li . .. . . . " VII. TARGET INTEGRATION A. GENERAL The primary ...kts 200 kts Direction 359.9 degrees 0 degrees From prelaunch 99 5* 0 0 4 5 @ G 2 3 00 ALT 01 Figure 9.6 IRIS Dial Box Fuctions 100 summary box for a...Description: The primary purpose of get tgt pos is to move the targets in the simulation. If the networking capability is in lise, the target positions for

Nightmare book

NASA Astrophysics Data System (ADS)

judithku; jajustin; tyler, d.

2017-02-01

In response to Kate Brown's review of Kate Moore's book The Radium Girls, which tells the depressing but important tale of female radium-dial painters in the early 1900s who contracted radiation poisoning.

Moving the Dial to Advance Population Health Equity in New York City Asian American Populations

PubMed Central

Trinh-Shevrin, Chau; Kwon, Simona C.; Nadkarni, Smiti Kapadia; Islam, Nadia S.

2015-01-01

The shift toward a health equity framework for eliminating the health disparities burden of racial/ethnic minority populations has moved away from a disease-focused model to a social determinants framework that aims to achieve the highest attainment of health for all. The New York University Center for the Study of Asian American Health (CSAAH) has identified core themes and strategies for advancing population health equity for Asian American populations in New York City that are rooted in the following: social determinants of health; multisectoral, community-engaged approaches; leveraging community assets; improved disaggregated data collection and access to care; and building sustainability through community leadership and infrastructure-building activities. We describe the strategies CSAAH employed to move the dial on population health equity. PMID:25905858

Single Frequency, Pulsed Laser Diode Transmitter for Dial Water Vapor Measurements at 935nm

NASA Technical Reports Server (NTRS)

Switzer, Gregg W.; Cornwell, Donald M., Jr.; Krainak, Michael A.; Abshire, James B.; Rall, Johnathan A. R.

1998-01-01

We report a tunable, single frequency, narrow linewidth, pulsed laser diode transmitter at 935.68nm for remote sensing of atmospheric water vapor. The transmitter consists of a CW, tunable, external cavity diode laser whose output is amplified 2OdB using a tapered diode amplifier. The output is pulsed for range resolved DIAL lidar by pulsing the drive current to the diode amplifier at 4kHz with a .5% duty cycle. The output from the transmitter is 36OnJ/pulse and is single spatial mode. It maintains a linewidth of less than 25MHz as its wavelength is tuned across the water vapor absorption line at 935.68nm. The transmitter design and its use in a water vapor measurement will be discussed.

Predictors of Suicide Ideation in a Random Digit Dial Study: Exposure to Suicide Matters.

PubMed

van de Venne, Judy; Cerel, Julie; Moore, Melinda; Maple, Myfanwy

2017-07-03

Suicide is an important public health concern requiring ongoing research to understand risk factors for suicide ideation. A dual-frame, random digit dial survey was utilized to identify demographic and suicide-related factors associated with suicide ideation in a statewide sample of 1,736 adults. The PH-Q 9 Depression scale suicide ideation question was used to assess current suicide ideation in both the full sample and suicide exposed sub-sample. Being non-married and having previous suicide exposure were separately associated with higher risks of suicide ideation in the full sample. Being male, having increased suicide exposures, and having increased perceptions of closeness to the decedent increased risks, while older age decreased risks for the suicide exposed. Implications for future screening and research are discussed.

Novel Technique and Technologies for Active Optical Remote Sensing of Greenhouse Gases

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Refaat, Tamer F.; Petros, Mulugeta

2017-01-01

The societal benefits of understanding climate change through identification of global carbon dioxide sources and sinks led to the desired NASA's active sensing of carbon dioxide emissions over nights, days, and seasons (ASCENDS) space-based missions of global carbon dioxide measurements. For more than 15 years, NASA Langley Research Center (LaRC) have developed several carbon dioxide active remote sensors using the differential absorption lidar (DIAL) technique operating at the two-micron wavelength. Currently, an airborne two-micron triple-pulse integrated path differential absorption (IPDA) lidar is under development. This IPDA lidar measures carbon dioxide as well as water vapor, the dominant interfering molecule on carbon dioxide remote sensing. Advancement of this triple-pulse IPDA lidar development is presented.

511 Case Studies : Arizona

DOT National Transportation Integrated Search

2001-01-01

This document is one of five case studies planned on the implementation of statewide 511 transportation information abbreviated telephone dialing codes. It provides a current snapshot of the progress being made in Arizona.

Developing AJN Network: phase two. An information resource for nurses.

PubMed Central

Rizzolo, M. A.; DuBois, K.

1995-01-01

In September of 1993 the American Journal of Nursing Company was awarded a three-year Special Projects Grant from the Division of Nursing, Department of Health and Human Services to develop a national information service that would provide a variety of formal and informal continuing education services to nurses in medically underserved communities. AJN Network went "live" in March 1994 and our progress in our first year of operation was presented at SCAMC in 1994. During the first year of operation, AJN Network was available through a dial in service. In September 1994 we became an Internet node. This presentation will detail our progress in Year 2 of the grant period, describing expansion of user base and content, new content offerings, initial stages of WEB development and plans for future development. PMID:8563246

KEA-144: Final Results of the Ground Operations Demonstration Unit for Liquid Hydrogen (GODU-LH2) Project

NASA Technical Reports Server (NTRS)

Notardonato, William; Fesmire, James; Swanger, Adam; Jumper, Kevin; Johnson, Wesley; Tomsik, Thomas

2017-01-01

GODU-LH2 system has successfully met all test objectives at the 33%, 67%, and 100% tank fill level. Complete control over the state of the fluid has been demonstrated using Integrated Refrigeration and Storage (IRAS). Almost any desired point along the H2saturation curve can essentially be "dialed in" and maintained indefinitely. System can also be used to produce densified hydrogen in large quantities to the triple point. Exploring multiple technology infusion paths. Studying implementation of IRAS technology into new LH2sphere for EM-2 at LC39B. Technical interchange also occurring with STMD, LSP, ULA, DoE, KIST, Kawasaki, Shell Oil, SpaceX, US Coast Guard, and Virgin Galactic.

Cumulus cloud venting of mixed layer ozone

NASA Technical Reports Server (NTRS)

Ching, J. K. S.; Shipley, S. T.; Browell, E. V.; Brewer, D. A.

1985-01-01

Observations are presented which substantiate the hypothesis that significant vertical exchange of ozone and aerosols occurs between the mixed layer and the free troposphere during cumulus cloud convective activity. The experiments utilized the airborne Ultra-Violet Differential Absorption Lidar (UV-DIAL) system. This system provides simultaneous range resolved ozone concentration and aerosol backscatter profiles with high spatial resolution. Evening transects were obtained in the downwind area where the air mass had been advected. Space-height analyses for the evening flight show the cloud debris as patterns of ozone typically in excess of the ambient free tropospheric background. This ozone excess was approximately the value of the concentration difference between the mixed layer and free troposphere determined from independent vertical soundings made by another aircraft in the afternoon.

Development of wavelength locking circuit for 1.53 micron water vapor monitoring coherent differential absorption LIDAR

NASA Astrophysics Data System (ADS)

Imaki, Masaharu; Kojima, Ryota; Kameyama, Shumpei

2018-04-01

We have studied a ground based coherent differential absorption LIDAR (DIAL) for vertical profiling of water vapor density using a 1.5μm laser wavelength. A coherent LIDAR has an advantage in daytime measurement compared with incoherent LIDAR because the influence of background light is greatly suppressed. In addition, the LIDAR can simultaneously measure wind speed and water vapor density. We had developed a wavelength locking circuit using the phase modulation technique and offset locking technique, and wavelength stabilities of 0.123 pm which corresponds to 16 MHz are realized. In this paper, we report the wavelength locking circuits for the 1.5 um wavelength.

The Dual Wavelength UV Transmitter Development for Space Based Ozone DIAL Measurements

NASA Technical Reports Server (NTRS)

Prasad, Narasimha S.

2008-01-01

The objective of this research is to develop efficient 1-micron to UV wavelength conversion technology to generate tunable, single mode, pulsed UV wavelengths of 320 nm and 308 nm. The 532 nm wavelength radiation is generated by a 1064 nm Nd:YAG laser through second harmonic generation. The 532 nm pumps an optical parametric oscillator (OPO) to generate 803 nm. The 320 nm is generated by sum frequency generation (SFG) of 532 nm and 803 nm wavelengths The hardware consists of a conductively cooled, 1 J/pulse, single mode Nd:YAG pump laser coupled to an efficient RISTRA OPO and SFG assembly-Both intra and extra-cavity approaches are examined for efficiency.

77 FR 74543 - Federal Advisory Committee Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-14

.../411593 . Dial-in: After you've connected your computer, audio connection instructions will be presented... the status of current research projects. FOR FURTHER INFORMATION CONTACT: The meeting is open to the...

511 case studies : Kentucky

DOT National Transportation Integrated Search

2000-11-01

This document is the first of five case studies planned on the implementation of statewide 511 transportation information abbreviated telephone dialing codes. It provides a current snapshot of the progress being made in Kentucky

21 CFR 886.4610 - Ocular pressure applicator.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4610 Ocular pressure applicator. (a... bulb, a dial indicator, a band, and bellows, intended to apply pressure on the eye in preparation for...

Music listening for maintaining attention of older adults with cognitive impairments.

PubMed

Gregory, Dianne

2002-01-01

Twelve older adults with cognitive impairments who were participants in weekly community-based group music therapy sessions, 6 older adults in an Alzheimer's caregivers' group, and 6 college student volunteers listened to a 3.5 minute prepared audiotape of instrumental excerpts of patriotic selections. The tape consisted of 7 excerpts ranging from 18 s to 34 s in duration. Each music excerpt was followed by a 7-9 s period of silence, a "wait" excerpt. Listeners were instructed to move a Continuous Response Digital Interface (CRDI) to the name of the music excerpt depicted on the CRDI overlay when they heard a music excerpt. Likewise, they were instructed to move the dial to the word "WAIT" when there was no music. They were also instructed to maintain the dial position for the duration of each music or silence excerpt. Statistical analysis indicated no significant differences between the caregivers' and the college students' group means for total dial changes, correct and incorrect recognitions, correct and incorrect responses to silence excerpts, and reaction times. The mean scores of these 2 groups were combined and compared with the mean scores of the group of elderly adults with cognitive impairments. The mean total dial changes were significantly lower for the listeners with cognitive impairments, resulting in significant differences in all of the other response categories except incorrect recognitions. In addition, their mean absence of response to silence excerpts was significantly higher than their mean absence of responding to music excerpts. Their mean reaction time was significantly slower than the comparison group's reaction time. To evaluate training effects, 10 of the original 12 music therapy participants repeated the listening task with assistance from the therapist (treatment) immediately following the first listening (baseline). A week later the order was reversed for the 2 listening trials. Statistical and graphic analysis of responses between first and second baseline responses indicate significant improvement in responses to silence and music excerpts over the 2 sessions. Applications of the findings to music listening interventions for maintaining attention, eliciting social interaction between clients or caregivers and their patients, and evaluating this population's affective responses to music are discussed.

47 CFR 1.80 - Forfeiture proceedings.

Code of Federal Regulations, 2010 CFR

2010-10-01

...,000 Violation of children's television commercialization or programming requirements 8,000 Violations...,320. Sec. 220(d) Common Carrier Records & Accounts 9,600/day. Sec. 223(b) Dial-a-Porn 75,000/day. Sec...

Analysis of DIAL/HSRL aerosol backscatter and extinction profiles during the SEAC4RS campaign with an aerosol assimilation system

NASA Astrophysics Data System (ADS)

Weaver, C. J.; da Silva, A. M., Jr.; Colarco, P. R.; Randles, C. A.

2015-12-01

We retrieve aerosol concentrations and optical information from vertical profiles of airborne 532 nm extinction and 532 and 1064 nm backscatter measurements made during the SEAC4RS summer 2013 campaign. The observations are from the High Spectral Resolution Lidar (HSRL) Airborne Differential Absorption Lidar (DIAL) on board the NASA DC-8. Instead of retrieving information about aerosol microphysical properties such as indexes of refraction, we seek information more directly applicable to an aerosol transport model - in our case the Goddard Chemistry Aerosol Radiation and Transport (GOCART) module used in the GEOS-5 Earth modeling system. A joint atmosphere/aerosol mini-reanalysis was performed for the SEAC4RS period using GEOS-5. The meteorological reanalysis followed the MERRA-2 atmospheric reanalysis protocol, and aerosol information from MODIS, MISR, and AERONET provided a constraint on the simulated aerosol optical depth (i.e., total column loading of aerosols). We focus on the simulated concentrations of 10 relevant aerosol species simulated by the GOCART module: dust, sulfate, and organic and black carbon. Our first retrieval algorithm starts with the SEAC4RS mini-reanalysis and adjusts the concentration of each GOCART aerosol species so that differences between the observed and simulated backscatter and extinction measurements are minimized. In this case, too often we are unable to simulate the observations by simple adjustment of the aerosol concentrations. A second retrieval approach adjusts both the aerosol concentrations and the optical parameters (i.e., assigned mass extinction efficiency) associated with each GOCART species. We present results from DC-8 flights over smoke from forest fires over the western US using both retrieval approaches. Finally, we compare our retrieved quantities with in-situ observations of aerosol absorption, scattering, and mass concentrations at flight altitude.

Aerosol-associated changes in tropical stratospheric ozone following the eruption of Mount Pinatubo

NASA Technical Reports Server (NTRS)

Grant, William B.; Browell, Edward V.; Fishman, Jack; Brackett, Vincent G.; Veiga, Robert E.; Nganga, Dominique; Minga, A.; Cros, Bernard; Butler, Carolyn F.; Fenn, Marta A.

1994-01-01

The large amount of sulfuric acid aerosol formed in the stratosphere by conversion of sulfur dioxide emitted by the eruption of Mount Pinatubo (15.14 deg N, 120.35 deg E) in the Philippines around June 15, 1991, has had a pronounced effect on lower stratospheric ozone in the tropics. Measurements of stratospheric ozone in the tropics using electrochemical concentration cell (ECC) sondes before and after the eruption and the airborne UV differential absorption lidar (DIAL) system after the eruption are compared with Stratospheric Aerosol and Gas Experiment II (SAGE II) measurements from several years before the eruption and ECC sonde measurements from the year prior to the eruption to determine the resulting changes. Ozone decreases of up to 33 % compared with SAGE II climatological values were found to be directly correlated with altitude regions of enhanced aerosol loading in the 16- to 28-km range. A maximum partial-column decrease of 29 +/- Dobson units (DU) was found over the 16- to 28-km range in September 1991 along with small increases (to 5.9 +/- 2 DU) from 28 to 31.5 km. A large decrease of ozone was also found at 4 deg to 8 deg S from May to August 1992, with a maximum decrease of 33 +/- 7 DU found above Brazzaville in July. Aerosol data form the visible channel of the advanced very high resolution radiometer (AVHRR) and the visible wavelength of the UV DIAL system were used to examine the relationship between aerosol (surface area) densities and ozone changes. The tropical stratospheric ozone changes we observed in 1991 and 1992 are likely be explained by a combination of dynamical (vertical transport) perturbations, radiative perturbations on ozone photochemistry, and heterogeneous chemistry.

Research on the improvement of traditional dial instrument precision based on C8051F020.

NASA Astrophysics Data System (ADS)

Sun, Guiling; Liu, Yi; Lu, Li

2006-11-01

Two essential parameters to weigh the quality of a reinforcing steel bar are the value of its bending force and the maximum pull it can withstand, in order to measure them with higher precision, it is significant to describe the changing tendency of force with time and displacement by drawing a real-time curve directly during the process examining the quality of a bar when the pull exerted is variable continuously. Using C8051F020 as the core component, this paper improves traditional dial instruments whose precision can only reach the second level. Adopting a high precision pulling/pressing force sensor, an amplifier, a two-order Butterworth low-pass filter and a 12-bit AD converter which is in the C8051F020, the first level of precision can be obtained. A rotary encoder is used to measure the length increment of the bar during the pulling process, based on an algorithm, a force-displacement (or time) curve which is quite important for operators to control the course of experiment can be displayed on the LCD. Meanwhile, real-time experimental data can be stored in local flash, or uploaded to PC by RS-485 and stored in the center database. A real-time clock is also adopted to mark the time of each experiment that is useful to index the data. The measure system we describe here is characterized by simple structure, high precision and stabilization, and convenience operation, can be used in other actual measure systems by only changing the front sensor, so it is of great value of application and popularization.

Precise Restraightening of Bent Studs

NASA Technical Reports Server (NTRS)

Boardman, R. E.

1982-01-01

Special tool quickly bends studs back into shape accurately and safely by force applied by hydraulic ram, with deflection being measured by dial indicator. Ram and indicator can be interchanged for straightening in reverse direction.

47 CFR 1.80 - Forfeiture proceedings.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Unauthorized substantial transfer of control 8,000 Violation of children's television commercialization or.... 223(b) Dial-a-Porn 75,000/day. Sec. 227(e) 10,000/violation.30,000/day for each day of continuing...

47 CFR 1.80 - Forfeiture proceedings.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Unauthorized substantial transfer of control 8,000 Violation of children's television commercialization or.... Sec. 223(b) Dial-a-Porn 80,000/day. Sec. 227(e) 10,000/violation. 30,000/day for each day of...

47 CFR 1.80 - Forfeiture proceedings.

Code of Federal Regulations, 2012 CFR

2012-10-01

... discrimination 9,000 Unauthorized substantial transfer of control 8,000 Violation of children's television...,320. Sec. 220(d) Common Carrier Records & Accounts 9,600/day. Sec. 223(b) Dial-a-Porn 75,000/day. Sec...

47 CFR 1.80 - Forfeiture proceedings.

Code of Federal Regulations, 2014 CFR

2014-10-01

... discrimination 9,000 Unauthorized substantial transfer of control 8,000 Violation of children's television...,320. Sec. 220(d) Common Carrier Records & Accounts 9,600/day. Sec. 223(b) Dial-a-Porn 80,000/day. Sec...

78 FR 5190 - National Cancer Institute; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-24

... Advisory Committee; Ad hoc Clinical Trials and Strategic Planning Subcommittee. Date: February 25, 2013... Group of the Ad hoc Clinical Trials Strategic Planning Subcommittee. Dial in number: 1-866-652-9542 and...

Customer Churn Prediction for Broadband Internet Services

NASA Astrophysics Data System (ADS)

Huang, B. Q.; Kechadi, M.-T.; Buckley, B.

Although churn prediction has been an area of research in the voice branch of telecommunications services, more focused studies on the huge growth area of Broadband Internet services are limited. Therefore, this paper presents a new set of features for broadband Internet customer churn prediction, based on Henley segments, the broadband usage, dial types, the spend of dial-up, line-information, bill and payment information, account information. Then the four prediction techniques (Logistic Regressions, Decision Trees, Multilayer Perceptron Neural Networks and Support Vector Machines) are applied in customer churn, based on the new features. Finally, the evaluation of new features and a comparative analysis of the predictors are made for broadband customer churn prediction. The experimental results show that the new features with these four modelling techniques are efficient for customer churn prediction in the broadband service field.

Database for chemical weapons detection: first results

NASA Astrophysics Data System (ADS)

Bellecci, C.; Gaudio, P.; Gelfusa, M.; Martellucci, S.; Richetta, M.; Ventura, P.; Antonucci, A.; Pasquino, F.; Ricci, V.; Sassolini, A.

2008-10-01

The quick increase of terrorism and asymmetric war is leading towards new needs involving defense and security. Nowadays we have to fight several kind of threats and use of chemical weapons against civil or military objectives is one of the most dangerous. For this reason it is necessary to find equipment, know-how and information that are useful in order to detect and identify dangerous molecules as quickly and far away as possible, so to minimize damage. Lidar/Dial are some of the most powerful optical technologies. Dial technology use two different wavelengths, in order to measure concentration profile of an investigated molecule. For this reason it is needed a "fingerprint" database which consists of an exhaustive collection of absorption coefficients data so to identify each molecule avoiding confusion with interfering ones. Nowadays there is not such a collection of data in scientific and technical literature. We used an FT-IR spectrometer and a CO2 laser source for absorption spectroscopy measurements using cells filled with the investigated molecules. The CO2 source is the transmitter of our DIAL facility. In this way we can make a proper "fingerprint" database necessary to identify dangerous molecules. The CO2 laser has been chosen because it is eye safe and, mainly, because it covers a spectral band where there is good absorption for this kind of molecules. In this paper IR spectra of mustard will be presented and compared to other substances which may interfere producing a false alarm. Methodology, experimental setup and first results are described.

Knowledge-based operation and management of communications systems

NASA Technical Reports Server (NTRS)

Heggestad, Harold M.

1988-01-01

Expert systems techniques are being applied in operation and control of the Defense Communications System (DCS), which has the mission of providing reliable worldwide voice, data and message services for U.S. forces and commands. Thousands of personnel operate DCS facilities, and many of their functions match the classical expert system scenario: complex, skill-intensive environments with a full spectrum of problems in training and retention, cost containment, modernization, and so on. Two of these functions are: (1) fault isolation and restoral of dedicated circuits at Tech Control Centers, and (2) network management for the Defense Switched Network (the modernized dial-up voice system currently replacing AUTOVON). An expert system for the first of these is deployed for evaluation purposes at Andrews Air Force Base, and plans are being made for procurement of operational systems. In the second area, knowledge obtained with a sophisticated simulator is being embedded in an expert system. The background, design and status of both projects are described.

Knowledge-based operation and management of communications systems

NASA Astrophysics Data System (ADS)

Heggestad, Harold M.

1988-11-01

Expert systems techniques are being applied in operation and control of the Defense Communications System (DCS), which has the mission of providing reliable worldwide voice, data and message services for U.S. forces and commands. Thousands of personnel operate DCS facilities, and many of their functions match the classical expert system scenario: complex, skill-intensive environments with a full spectrum of problems in training and retention, cost containment, modernization, and so on. Two of these functions are: (1) fault isolation and restoral of dedicated circuits at Tech Control Centers, and (2) network management for the Defense Switched Network (the modernized dial-up voice system currently replacing AUTOVON). An expert system for the first of these is deployed for evaluation purposes at Andrews Air Force Base, and plans are being made for procurement of operational systems. In the second area, knowledge obtained with a sophisticated simulator is being embedded in an expert system. The background, design and status of both projects are described.

The Steerable Microcatheter: A New Device for Selective Catheterisation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soyama, Takeshi; Yoshida, Daisuke; Sakuhara, Yusuke, E-mail: yusaku@med.hokudai.ac.jp

The steerable microcatheter (SwiftNINJA, Sumitomo Bakelite, Tokyo, Japan), which has a remote-controlled flexible tip manipulated using a dial in the handgrip, was recently developed and delivered to the market. This device enables the user to change the angle of the microcatheter tip manually, and potentially makes selective catheterisation easier. We evaluated its unique characteristics and utility in selective catheterisation and coil embolization. This article describes: (1) the advantages of this device in catheterisations involving acute angle branches, and (2) a new technique of compact coil packing with the use of intentional folding by the bendable tip of the catheter.

An experimental/analytical program to assess the utility of lidar for pollution monitoring

NASA Technical Reports Server (NTRS)

Mills, F. S.; Allen, R. J.; Butler, C. F.; Kindle, E. C.

1978-01-01

The development and demonstration of lidar techniques for the remote measurement of atmospheric constituents and transport processes in the lower troposphere was carried out. Particular emphasis was given to techniques for monitoring SO2 and particulates, the principal pollutants in power plant and industrial plumes. Data from a plume dispersion study conducted in Maryland during September and October 1976 were reduced, and a data base was assembled which is available to the scientific community for plume model verification. A UV Differential Absorption Lidar (DIAL) was built, and preliminary testing was done.

Distributed On-line Monitoring System Based on Modem and Public Phone Net

NASA Astrophysics Data System (ADS)

Chen, Dandan; Zhang, Qiushi; Li, Guiru

In order to solve the monitoring problem of urban sewage disposal, a distributed on-line monitoring system is proposed. By introducing dial-up communication technology based on Modem, the serial communication program can rationally solve the information transmission problem between master station and slave station. The realization of serial communication program is based on the MSComm control of C++ Builder 6.0.The software includes real-time data operation part and history data handling part, which using Microsoft SQL Server 2000 for database, and C++ Builder6.0 for user interface. The monitoring center displays a user interface with alarm information of over-standard data and real-time curve. Practical application shows that the system has successfully accomplished the real-time data acquisition from data gather station, and stored them in the terminal database.

Associations of distraction involvement and age with driver injury severities.

PubMed

Donmez, Birsen; Liu, Zishu

2015-02-01

This paper investigates the associations between the severity of injuries sustained by a driver who is involved in a two-vehicle crash, the existence and type of driver distraction as well as driver's age. Few studies investigated distraction as it relates to injury severity. Moreover, these studies did not consider driver age which is a significant factor related to driving behavior and the ability to respond in a crash situation. An ordered logit model was built to predict injury severity sustained by drivers using data from the U.S. National Automotive Sampling System's General Estimates System (2003 to 2008). Various factors (e.g., weather, gender, and speeding) were statistically controlled for, but the main focus was on the interaction of driver age and distraction type. The trends observed for young and mid-age drivers were similar. For these age groups, dialing or texting on the cell phone, passengers, and in-vehicle sources resulted in an increase in a likelihood of more severe injuries. Talking on the cell phone had a similar effect for younger drivers but was not significant for mid-age drivers. Inattention and distractions outside the vehicle decreased the odds of severe injuries. For older drivers, the highest odds of severe injuries were observed with dialing or texting on a cell phone, followed by in-vehicle sources and talking on the cell phone. All these sources were associated with an increased likelihood of injury severity. Similar to young and mid-age drivers, distractions outside the vehicle decreased the odds of severe injuries. Other distraction types did not have a significant effect for the older age group. The results support previous literature and extend our understanding of crash injury severity. The findings have implications for policy making and the design of distraction mitigation systems. Copyright © 2014 National Safety Council and Elsevier Ltd. All rights reserved.

Triple-Pulse Integrated Path Differential Absorption Lidar for Carbon Dioxide Measurement - Novel Lidar Technologies and Techniques with Path to Space

NASA Technical Reports Server (NTRS)

Singh, Upendra N.; Refaat, Tamer F.; Petros, Mulugeta

2017-01-01

The societal benefits of understanding climate change through identification of global carbon dioxide sources and sinks led to the desired NASA's active sensing of carbon dioxide emissions over nights, days, and seasons (ASCENDS) space-based missions of global carbon dioxide measurements. For more than 15 years, NASA Langley Research Center (LaRC) have developed several carbon dioxide active remote sensors using the differential absorption lidar (DIAL) technique operating at the two-micron wavelength. Currently, an airborne two-micron triple-pulse integrated path differential absorption (IPDA) lidar is under development. This IPDA lidar measures carbon dioxide as well as water vapor, the dominant interfering molecule on carbon dioxide remote sensing. Advancement of this triple-pulse IPDA lidar development is presented.

17 CFR 250.21 - Filing of documents.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 20549. Except as otherwise provided by the rules, such documents shall be deemed to have been filed with... direct transmission, via dial-up modem or Internet. (2) The date of filing of documents shall be...

17 CFR 250.21 - Filing of documents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 20549. Except as otherwise provided by the rules, such documents shall be deemed to have been filed with... direct transmission, via dial-up modem or Internet. (2) The date of filing of documents shall be...

LOTOS: A Proposed Lower Tropospheric Observing System from the Land Surface through the Atmospheric Boundary Layer

NASA Astrophysics Data System (ADS)

Cohn, S. A.; Lee, W. C.; Carbone, R. E.; Oncley, S.; Brown, W. O. J.; Spuler, S.; Horst, T. W.

2015-12-01

Advances in sensor capabilities, but also in electronics, optics, RF communication, and off-the-grid power are enabling new measurement paradigms. NCAR's Earth Observing Laboratory (EOL) is considering new sensors, new deployment modes, and integrated observing strategies to address challenges in understanding within the atmospheric boundary layer and the underlying coupling to the land surface. Our vision is of a network of deployable observing sites, each with a suite of complementary instruments that measure surface-atmosphere exchange, and the state and evolution of the boundary layer. EOL has made good progress on distributed surface energy balance and flux stations, and on boundary layer remote sensing of wind and water vapor, all suitable for deployments of combined instruments and as network of such sites. We will present the status of the CentNet surface network development, the 449-MHz modular wind profiler, and a water vapor and temperature profiling differential absorption lidar (DIAL) under development. We will further present a concept for a test bed to better understand the value of these and other possible instruments in forming an instrument suite flexible for multiple research purposes.

GAUGING APPARATUS

DOEpatents

Ruggles, C.A.

1957-08-27

A swinging arm gage designed to measure radial angles, tapering, sloping, or arcuate concave surfaces is described. The principle of the swinging arm gage is that in any spherical system, radii and radial lines established by them pass through the center of the sphere. Thus if an arm be made to pivot at the sphere center, the path of the swinging end can be guided by a can so set as to establish the proper center angle, and dial indicators on the arm can be zeroed on a master object, angular and dimensional manufacturing errors can be determined on a duplicate object. This device makes possible a considerable saving of time in measuring complex arcuate contours.

General Aviation Flight Test of Advanced Operations Enabled by Synthetic Vision

NASA Technical Reports Server (NTRS)

Glaab, Louis J.; Hughhes, Monica F.; Parrish, Russell V.; Takallu, Mohammad A.

2014-01-01

A flight test was performed to compare the use of three advanced primary flight and navigation display concepts to a baseline, round-dial concept to assess the potential for advanced operations. The displays were evaluated during visual and instrument approach procedures including an advanced instrument approach resembling a visual airport traffic pattern. Nineteen pilots from three pilot groups, reflecting the diverse piloting skills of the General Aviation pilot population, served as evaluation subjects. The experiment had two thrusts: 1) an examination of the capabilities of low-time (i.e., <400 hours), non-instrument-rated pilots to perform nominal instrument approaches, and 2) an exploration of potential advanced Visual Meteorological Conditions (VMC)-like approaches in Instrument Meteorological Conditions (IMC). Within this context, advanced display concepts are considered to include integrated navigation and primary flight displays with either aircraft attitude flight directors or Highway In The Sky (HITS) guidance with and without a synthetic depiction of the external visuals (i.e., synthetic vision). Relative to the first thrust, the results indicate that using an advanced display concept, as tested herein, low-time, non-instrument-rated pilots can exhibit flight-technical performance, subjective workload and situation awareness ratings as good as or better than high-time Instrument Flight Rules (IFR)-rated pilots using Baseline Round Dials for a nominal IMC approach. For the second thrust, the results indicate advanced VMC-like approaches are feasible in IMC, for all pilot groups tested for only the Synthetic Vision System (SVS) advanced display concept.

Quantum cascade transmitters for ultrasensitive chemical agent and explosives detection

NASA Astrophysics Data System (ADS)

Schultz, John F.; Taubman, Matthew S.; Harper, Warren W.; Williams, Richard M.; Myers, Tanya L.; Cannon, Bret D.; Sheen, David M.; Anheier, Norman C., Jr.; Allen, Paul J.; Sundaram, S. K.; Johnson, Bradley R.; Aker, Pamela M.; Wu, Ming C.; Lau, Erwin K.

2003-07-01

The small size, high power, promise of access to any wavelength between 3.5 and 16 microns, substantial tuning range about a chosen center wavelength, and general robustness of quantum cascade (QC) lasers provide opportunities for new approaches to ultra-sensitive chemical detection and other applications in the mid-wave infrared. PNNL is developing novel remote and sampling chemical sensing systems based on QC lasers, using QC lasers loaned by Lucent Technologies. In recent months laboratory cavity-enhanced sensing experiments have achieved absorption sensitivities of 8.5 x 10-11 cm-1 Hz-1/2, and the PNNL team has begun monostatic and bi-static frequency modulated, differential absorption lidar (FM DIAL) experiments at ranges of up to 2.5 kilometers. In related work, PNNL and UCLA are developing miniature QC laser transmitters with the multiplexed tunable wavelengths, frequency and amplitude stability, modulation characteristics, and power levels needed for chemical sensing and other applications. Current miniaturization concepts envision coupling QC oscillators, QC amplifiers, frequency references, and detectors with miniature waveguides and waveguide-based modulators, isolators, and other devices formed from chalcogenide or other types of glass. Significant progress has been made on QC laser stabilization and amplification, and on development and characterization of high-purity chalcogenide glasses, waveguide writing techniques, and waveguide metrology.

Last results of technological developments for ultra-lightweight, large aperture, deployable mirror for space telescopes

NASA Astrophysics Data System (ADS)

Gambicorti, Lisa; D'Amato, Francesco; Vettore, Christian; Duò, Fabrizio; Guercia, Alessio; Patauner, Christian; Biasi, Roberto; Lisi, Franco; Riccardi, Armando; Gallieni, Daniele; Lazzarini, Paolo; Tintori, Matteo; Zuccaro Marchi, Alessandro; Pereira do Carmo, Joao

2017-11-01

The aim of this work is to describe the latest results of new technological concepts for Large Aperture Telescopes Technology (LATT) using thin deployable lightweight active mirrors. This technology is developed under the European Space Agency (ESA) Technology Research Program and can be exploited in all the applications based on the use of primary mirrors of space telescopes with large aperture, segmented lightweight telescopes with wide Field of View (FOV) and low f/#, and LIDAR telescopes. The reference mission application is a potential future ESA mission, related to a space borne DIAL (Differential Absorption Lidar) instrument operating around 935.5 nm with the goal to measure water vapor profiles in atmosphere. An Optical BreadBoard (OBB) for LATT has been designed for investigating and testing two critical aspects of the technology: 1) control accuracy in the mirror surface shaping. 2) mirror survivability to launch. The aim is to evaluate the effective performances of the long stroke smart-actuators used for the mirror control and to demonstrate the effectiveness and the reliability of the electrostatic locking (EL) system to restraint the thin shell on the mirror backup structure during launch. The paper presents a comprehensive vision of the breadboard focusing on how the requirements have driven the design of the whole system and of the various subsystems. The manufacturing process of the thin shell is also presented.

Bio-recognition and detection using liquid crystals.

PubMed

Hussain, A; Pina, A S; Roque, A C A

2009-09-15

Liquid crystals (LCs) are used extensively by the electronics industry as display devices. Advances in the understanding of the liquid crystalline phase and the chemistry therein lead to the development of LC exhibiting faster switching speed with greater twist angle. This in turn lead to the emergence of liquid crystal displays, rendering dial-and-needle based displays (such as those used in various meters) and cathode ray tubes obsolete. In this article, we review the history of LC and their emergence as an invaluable material for display devices and the more recent discovery of their use as sensing elements in biosensors. This new application of LC as tools in the development of fast and simple biosensors is envisaged to gain more importance in the foreseeable future.

Design of Advanced Atmospheric Water Vapor Differential Absorption Lidar (DIAL) Detection System

NASA Technical Reports Server (NTRS)

Refaat, Tamer F.; Luck, William S., Jr.; DeYoung, Russell J.

1999-01-01

The measurement of atmospheric water vapor is very important for understanding the Earth's climate and water cycle. The lidar atmospheric sensing experiment (LASE) is an instrument designed and operated by the Langley Research Center for high precision water vapor measurements. The design details of a new water vapor lidar detection system that improves the measurement sensitivity of the LASE instrument by a factor of 10 are discussed. The new system consists of an advanced, very low noise, avalanche photodiode (APD) and a state-of-the-art signal processing circuit. The new low-power system is also compact and lightweight so that it would be suitable for space flight and unpiloted atmospheric vehicles (UAV) applications. The whole system is contained on one small printed circuit board (9 x 15 sq cm). The detection system is mounted at the focal plane of a lidar receiver telescope, and the digital output is read by a personal computer with a digital data acquisition card.

Measuring the performance of telephone-based disease surveillance systems in local health departments.

PubMed

Dausey, David J; Chandra, Anita; Schaefer, Agnes G; Bahney, Ben; Haviland, Amelia; Zakowski, Sarah; Lurie, Nicole

2008-09-01

We tested telephone-based disease surveillance systems in local health departments to identify system characteristics associated with consistent and timely responses to urgent case reports. We identified a stratified random sample of 74 health departments and conducted a series of unannounced tests of their telephone-based surveillance systems. We used regression analyses to identify system characteristics that predicted fast connection with an action officer (an appropriate public health professional). Optimal performance in consistently connecting callers with an action officer in 30 minutes or less was achieved by 31% of participating health departments. Reaching a live person upon dialing, regardless of who that person was, was the strongest predictor of optimal performance both in being connected with an action officer and in consistency of connection times. Health departments can achieve optimal performance in consistently connecting a caller with an action officer in 30 minutes or less and may improve performance by using a telephone-based disease surveillance system in which the phone is answered by a live person at all times.

Promoting Community Health Resources: Preferred Communication Strategies

USDA-ARS?s Scientific Manuscript database

Background: Community health promotion efforts involve communicating resource information to priority populations. Which communication strategies are most effective is largely unknown for specific populations. Objective: A random-dialed telephone survey was conducted to assess health resource comm...

Le mécanisme d'Anticythère, une machine bien mystérieuse (1)

NASA Astrophysics Data System (ADS)

Dupas, Jean-Jacques

2016-09-01

A roman shipwreck was discovered in 1900, near the coast of a small island, Antikythera. Among findings was an object full of gears and axles, with inscriptions. It is called Antikythera Mechanism. The interdisciplinary researches, with modern technics (tomography), proved that it is a mechanical calculating device which displays calendars and related astronomical phenomena : egyptian calendar, metonic calendar, callipic calendar, Saros and Exelgimos dials, Games dials, Sun's motion, Moon's motion realized through a remarkable epicycle gears train. The origin of the Mechanism and his designer are unknown. However, it was probably built during the second half of the 2nd century BCE, as part of the tradition of “sphere making” originated by Archimedes. May be, Poseidonios, from Rhodes, would be the designer. Antikythera Mechanism has not delivered all its mysteries yet. A second paper in a following issue of "l'Astronomie" is devoted to the subject.

Laser diode absorption spectroscopy for accurate CO(2) line parameters at 2 microm: consequences for space-based DIAL measurements and potential biases.

PubMed

Joly, Lilian; Marnas, Fabien; Gibert, Fabien; Bruneau, Didier; Grouiez, Bruno; Flamant, Pierre H; Durry, Georges; Dumelie, Nicolas; Parvitte, Bertrand; Zéninari, Virginie

2009-10-10

Space-based active sensing of CO(2) concentration is a very promising technique for the derivation of CO(2) surface fluxes. There is a need for accurate spectroscopic parameters to enable accurate space-based measurements to address global climatic issues. New spectroscopic measurements using laser diode absorption spectroscopy are presented for the preselected R30 CO(2) absorption line ((20(0)1)(III)<--(000) band) and four others. The line strength, air-broadening halfwidth, and its temperature dependence have been investigated. The results exhibit significant improvement for the R30 CO(2) absorption line: 0.4% on the line strength, 0.15% on the air-broadening coefficient, and 0.45% on its temperature dependence. Analysis of potential biases of space-based DIAL CO(2) mixing ratio measurements associated to spectroscopic parameter uncertainties are presented.

Non-coincident Inter-instrument Comparisons of Ozone Measurements Using Quasi-conservative Coordinates

NASA Technical Reports Server (NTRS)

Lait, L. R.; Newman, P. A.; Schoeberl, M. R.; McGee, T.; Twigg, T.; Browell, E.; Bevilacqua, R.; Andersen, S. B.; DeBacker, H.; Benesova, A.

2004-01-01

Ozone measurements from ozonesondes, AROTAL, DIAL, and POAM III instruments during the SOLVE-2/VINTERSOL period are composited in a time-varying, flow-following quasi-conservative (PV-6) coordinate space; the resulting composites from each instrument are mapped onto the other instruments locations and times. The mapped data are then used to intercompare data from the different instruments. Overall, the four data sets are found to be in good agreement. AROTAL shows somewhat lower values below 16 km, and DIAL has a positive bias at the upper limits of its altitude range. These intercomparisons are consistent with those obtained from more conventional near-coincident profiles, where available. Although the PV-theta mapping technique entails larger uncertainties of individual profile differences compared to direct near-coincident comparisons, the ability to include much larger numbers of comparisons can make this technique advantageous.

Does Talking on a Cell Phone, With a Passenger, or Dialing Affect Driving Performance? An Updated Systematic Review and Meta-Analysis of Experimental Studies.

PubMed

Caird, Jeff K; Simmons, Sarah M; Wiley, Katelyn; Johnston, Kate A; Horrey, William J

2018-02-01

Objective An up-to-date meta-analysis of experimental research on talking and driving is needed to provide a comprehensive, empirical, and credible basis for policy, legislation, countermeasures, and future research. Background The effects of cell, mobile, and smart phone use on driving safety continues to be a contentious societal issue. Method All available studies that measured the effects of cell phone use on driving were identified through a variety of search methods and databases. A total of 93 studies containing 106 experiments met the inclusion criteria. Coded independent variables included conversation target (handheld, hands-free, and passenger), setting (laboratory, simulation, or on road), and conversation type (natural, cognitive task, and dialing). Coded dependent variables included reaction time, stimulus detection, lane positioning, speed, headway, eye movements, and collisions. Results The overall sample had 4,382 participants, with driver ages ranging from 14 to 84 years ( M = 25.5, SD = 5.2). Conversation on a handheld or hands-free phone resulted in performance costs when compared with baseline driving for reaction time, stimulus detection, and collisions. Passenger conversation had a similar pattern of effect sizes. Dialing while driving had large performance costs for many variables. Conclusion This meta-analysis found that cell phone and passenger conversation produced moderate performance costs. Drivers minimally compensated while conversing on a cell phone by increasing headway or reducing speed. A number of additional meta-analytic questions are discussed. Application The results can be used to guide legislation, policy, countermeasures, and future research.

The assessment of ride service programs as an alcohol countermeasure

DOT National Transportation Integrated Search

1988-01-01

Ride Service Programs, frequently called safe ride or dial-a-ride programs, attempt to reduce alcohol-related crashes by providing alternative transportation to drinkers who would otherwise drive while intoxicated. This study identified 325 Ride Serv...

Paratransit Integration Symposium Proceedings, October 14, 1977

DOT National Transportation Integrated Search

1978-06-01

Paratransit innovation is considered by DOT/UMTA to be an essential part of the provision of public transportation. A variety of service options, ranging from many-to-many dial-a-ride to subscription ridership, offer cost effective options to convent...

75 FR 33821 - Section 8 Random Digit Dialing Fair Market Rent Surveys

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-15

... fast, inexpensive way to estimate Section 8 Fair Market Rents (FMRs) in areas not covered by the... Proposed Use: This survey provides HUD with a fast, inexpensive way to estimate Section 8 Fair Market Rents...

Reading recognition of pointer meter based on pattern recognition and dynamic three-points on a line

NASA Astrophysics Data System (ADS)

Zhang, Yongqiang; Ding, Mingli; Fu, Wuyifang; Li, Yongqiang

2017-03-01

Pointer meters are frequently applied to industrial production for they are directly readable. They should be calibrated regularly to ensure the precision of the readings. Currently the method of manual calibration is most frequently adopted to accomplish the verification of the pointer meter, and professional skills and subjective judgment may lead to big measurement errors and poor reliability and low efficiency, etc. In the past decades, with the development of computer technology, the skills of machine vision and digital image processing have been applied to recognize the reading of the dial instrument. In terms of the existing recognition methods, all the parameters of dial instruments are supposed to be the same, which is not the case in practice. In this work, recognition of pointer meter reading is regarded as an issue of pattern recognition. We obtain the features of a small area around the detected point, make those features as a pattern, divide those certified images based on Gradient Pyramid Algorithm, train a classifier with the support vector machine (SVM) and complete the pattern matching of the divided mages. Then we get the reading of the pointer meter precisely under the theory of dynamic three points make a line (DTPML), which eliminates the error caused by tiny differences of the panels. Eventually, the result of the experiment proves that the proposed method in this work is superior to state-of-the-art works.

Progress in coherent laser radar

NASA Technical Reports Server (NTRS)

Vaughan, J. M.

1986-01-01

Considerable progress with coherent laser radar has been made over the last few years, most notably perhaps in the available range of high performance devices and components and the confidence with which systems may now be taken into the field for prolonged periods of operation. Some of this increasing maturity was evident at the 3rd Topical Meeting on Coherent Laser Radar: Technology and Applications. Topics included in discussions were: mesoscale wind fields, nocturnal valley drainage and clear air down bursts; airborne Doppler lidar studies and comparison of ground and airborne wind measurement; wind measurement over the sea for comparison with satellite borne microwave sensors; transport of wake vortices at airfield; coherent DIAL methods; a newly assembled Nd-YAG coherent lidar system; backscatter profiles in the atmosphere and wavelength dependence over the 9 to 11 micrometer region; beam propagation; rock and soil classification with an airborne 4-laser system; technology of a global wind profiling system; target calibration; ranging and imaging with coherent pulsed and CW system; signal fluctuations and speckle. Some of these activities are briefly reviewed.

Determining the maximum charging currents of lithium-ion cells for small charge quantities

NASA Astrophysics Data System (ADS)

Grimsmann, F.; Gerbert, T.; Brauchle, F.; Gruhle, A.; Parisi, J.; Knipper, M.

2017-10-01

In order to optimize the operating parameters of battery management systems for electric and hybrid vehicles, great interest has been shown in achieving the maximum permissible charging currents during recuperation, without causing a cell damage due to lithium plating, in relation to the temperature, charge quantity and state of charge. One method for determining these recuperation currents is measuring the cell thickness, where excessively high charging currents can be detected by an irreversible increase in thickness. It is not possible to measure particularly small charge quantities by employing mechanic dial indicators, which have a limited resolution of 1 μm. This is why we developed a measuring setup that has a resolution limit of less than 10 nm using a high-resolution contactless inductance sensor. Our results show that the permissible charging current I can be approximated in relation to the charge quantity x by a correlating function I =a /√{(x) } which is compliant with the Arrhenius law. Small charge quantities therefore have an optimization potential for energy recovery during recuperation.

47 CFR 64.3000 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES (CONTINUED) MISCELLANEOUS... calls. Any call initiated by an end user by dialing 911 for the purpose of accessing an emergency service provider. For wireless carriers, all 911 calls include those they are required to transmit...

Facility Focus: Historic Renovations.

ERIC Educational Resources Information Center

College Planning & Management, 2002

2002-01-01

Describes the renovation of historic buildings at Rice University (conversion of the Chemistry Building into space for the biophysics and bioengineering departments) and at Princeton University (renovation of the Dial Lodge eating club into a building for the Bendheim Center for Finance). Includes photographs. (EV)

Online Help from IBM.

ERIC Educational Resources Information Center

Moore, Jack

1988-01-01

The article describes the IBM/Special Needs Exchange which consists of: (1) electronic mail, conferencing, and a library of text and program files on the CompuServe Information Service; and (2) a dial-in database of special education software for IBM and compatible computers. (DB)

Autonomous dial-a-ride transit : benefit-cost evaluation

DOT National Transportation Integrated Search

1998-08-01

Among public transit and for-hire modes, fixed-route bus and rail are most effective in maintaining high ridership in high density areas such as urban centers. The cost effectiveness of fixed-route transit, however, depends on close proximity to the ...

Dialing for Dollars: Telecommunication Pays.

ERIC Educational Resources Information Center

Manning, Sherry

1999-01-01

Advances in telecommunications and provision of telecommunications services to college students can increase institutional revenue, improve campus and educational services, and aid in student retention. Colleges and universities have used creative financing to fund initial telecommunications investments and upgrades. Cash flow through student…

Making the Difference : Transportation Alternatives for Elderly and Handicapped Persons

DOT National Transportation Integrated Search

1979-08-01

This report contains project summaries of four examples of public transportation services for Elderly and Handicapped persons: the LIFT Project in Portland, OR; Roanoke Agencies Dial-A-Ride (RADAR) in Roanoke, VA; the Reduced Taxi Rate Program (RTR) ...

21 CFR 830.10 - Incorporation by reference.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Department, 25 West 43rd St., 4th floor, New York, NY 10036, phone: 212-642-4980, and may be ordered online... (dialing from the United States): 011-41-22-749-0111, and may be ordered online at http://www.standardsinfo...

Implementing 511 in Virginia and the Washington, DC metro area

DOT National Transportation Integrated Search

2001-04-20

On July 21, 2000, the Federal Communications Commission assigned the abbreviated dialing code 511 to be used for traveler information services. The basis for reserving 511 is that it meets the "public interest" standard for such a determination, and ...

BIOGEOCHEMICAL STUDIES OF PHOTOSYNTHETIC MICROBIAL MATS AND THEIR BIOTA

NASA Technical Reports Server (NTRS)

DesMarais, David; Discipulo, M.; Turk, K.; Londry, K. L.

2005-01-01

Photosynthetic microbial mats offer an opportunity to define holistic functionality at the millimeter scale. At the same time. their biogeochemistry contributes to environmental processes on a planetary scale. These mats are possibly direct descendents of the most ancient biological communities; communities in which oxygenic photosynthesis might have been invented. Mats provide one of the best natural systems to study how microbial populations associate to control dynamic biogeochemical gradients. These are self- sustaining, complete ecosystems in which light energy absorbed over a dial (24 hour) cycle drives the synthesis of spatially-organized, diverse biomass. Tightly-coupled microorganisms in the mat have specialized metabolisms that catalyze transformations of carbon, nitrogen, sulfur, and a host of other elements.

Air chemistry over the tropical forest of Guyana

NASA Technical Reports Server (NTRS)

Gregory, G. L.; Harriss, R. C.; Talbot, R. W.; Browell, E. V.; Beck, S. M.; Sebacher, D. I.; Rasmussen, R. A.; Garstang, M.; Andreae, M. O.; Hinton, R. R.

1986-01-01

A comparison is made of the atmospheric chemistry within and above the atmospheric boundary layer over the tropical forest of Guyana. The data were gathered by NASA during the Global Tropospheric Experiment program in 1984, with an instrumented aircraft being used to collect data at altitudes of 3.5 km and between 150-450 m. The synoptic data covered concentrations of O3, CO, dimethylsulfide (DMS), halocarbons and isoprene and three different aerosol particulate measurements (DIAL system). The forest boundary layer proved to be a significant sink for O3, and a source for substantial emissions of DMS. Isoprene emitted by the forest was photochemically oxidized and became a source of CO.

Volcanic-aerosol-induced changes in stratospheric ozone following the eruption of Mount Pinatubo

NASA Technical Reports Server (NTRS)

Grant, W. B.; Browell, E. V.; Fishman, J.; Brackett, V. G.; Fenn, M. A.; Butler, C. F.; Nganga, D.; Minga, A.; Cros, B.; Mayor, S. D.

1994-01-01

Measurements of lower stratospheric ozone in the Tropics using electrochemical concentrations cell (ECC) sondes and the airborne UV Differential Absorption Lidar (DIAL) system after the eruption of Mt. Pinatubo are compared with the Stratospheric Aerosol and Gas Experiment 2 (SAGE 2) and ECC sonde measurements from below the eruption to determine what changes have occurred as a result. Aerosol data from the Advanced Very High Resolution Radiometer (AVHRR) and the visible and IR wavelengths of the lidar system are used to examine the relationship between aerosols and ozone changes. Ozone decreases of 30 percent at altitudes between 19 and 26 km, partial column (16-28 km) decreases of about 27 D.U., and slight increases (5.4 D.U.) between 28 and 31 km are found in comparison with SAGE 2 climatological values.

Solid State Laser Technology Development for Atmospheric Sensing Applications

NASA Technical Reports Server (NTRS)

Barnes, James C.

1998-01-01

NASA atmospheric scientists are currently planning active remote sensing missions that will enable global monitoring of atmospheric ozone, water vapor, aerosols and clouds as well as global wind velocity. The measurements of these elements and parameters are important because of the effects they have on climate change, atmospheric chemistry and dynamics, atmospheric transport and, in general, the health of the planet. NASA will make use of Differential Absorption Lidar (DIAL) and backscatter lidar techniques for active remote sensing of molecular constituents and atmospheric phenomena from advanced high-altitude aircraft and space platforms. This paper provides an overview of NASA Langley Research Center's (LaRC's) development of advanced solid state lasers, harmonic generators, and wave mixing techniques aimed at providing the broad range of wavelengths necessary to meet measurement goals of NASA's Earth Science Enterprise.

2007 transportation needs and issues survey : summary of statewide results.

DOT National Transportation Integrated Search

2007-07-01

The Transportation Needs and Issues Survey was conducted in October and November of 2006 by the Survey Research Center at : Oregon State University. The survey used a random digit dialing telephone survey method and completed a total of 1,013 intervi...

78 FR 25699 - Foreign-Trade Zone (FTZ) 265-Conroe, Texas; Notification of Proposed Production Activity; Bauer...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-02

... foreign status components used in export production. On its domestic sales, Bauer would be able to choose... bands, plates, sheets, strips, bands), paper sheets/dials/rolls, articles of steel (shapes; U, H and I...

Patterns of Nitrogen Fixation and Related Genetic Diversity (nifH) in Microbial Mats and Stromatolites from Different Environments

NASA Astrophysics Data System (ADS)

Beltrán, Y. Y.; Centeno, C.; Falcón, L. I.

2010-04-01

We want to estimate the patterns of nitrogen fixation and the related genetic diversity (nifH) of microbial mats and microbialites on dial and temporal scales along a physicochemical and geographical gradient.

Response of genioglossus muscle to increasing chemical drive in sleeping obstructive apnea patients.

PubMed

Loewen, Andrea H S; Ostrowski, Michele; Laprairie, John; Maturino, Frances; Hanly, Patrick J; Younes, Magdy

2011-08-01

Subjects with a collapsible upper airway must activate their pharyngeal dilators sufficiently in response to increasing chemical drive if they are to maintain airway patency without arousal from sleep. Little is known about the response of pharyngeal dilators to increasing chemical drive in these subjects. We wished to determine, in obstructive apnea patients, the response of the genioglossus to increasing chemical drive and the contribution of mechanoreceptor feedback to this response. Physiological study. University-based sleep laboratory. 20 patients with obstructive apnea. Genioglossus activity was monitored during overnight polysomnography on optimal continuous positive airway pressure (CPAP). Intermittently, inspired gases were altered to produce different levels of ventilatory stimulation. CPAP was then briefly reduced to 1.0 cm H(2)O (dial-down), inducing an obstruction. Without mechanoreceptor feedback (i.e., on CPAP) the increase in genioglossus activity as ventilation increased from 6.1 ± 1.4 to 16.1 ± 4.8 L/min was modest (ΔTonic activity 0.3% ± 0.5%maximum; ΔPhasic activity 1.7% ± 3.4%maximum). Genioglossus activity increased immediately upon dial-down, reflecting mechanoreceptor feedback, but only when ventilation before dial-down exceeded a threshold value. This threshold varied among patients and, once surpassed, genioglossus activity increased briskly with further increases in chemical drive (1.1% ± 0.84%GG(MAX) per L/min increase in V(E)). In sleeping obstructive apnea patients: (1) Mechanoreceptor feedback is responsible for most of the genioglossus response to chemical drive. (2) Mechanoreceptor feedback is effective only above a threshold chemical drive, which varies greatly among patients. These findings account in part for the highly variable relation between pharyngeal mechanical abnormalities and apnea severity.

Metaheuristics for the dynamic stochastic dial-a-ride problem with expected return transports.

PubMed

Schilde, M; Doerner, K F; Hartl, R F

2011-12-01

The problem of transporting patients or elderly people has been widely studied in literature and is usually modeled as a dial-a-ride problem (DARP). In this paper we analyze the corresponding problem arising in the daily operation of the Austrian Red Cross. This nongovernmental organization is the largest organization performing patient transportation in Austria. The aim is to design vehicle routes to serve partially dynamic transportation requests using a fixed vehicle fleet. Each request requires transportation from a patient's home location to a hospital (outbound request) or back home from the hospital (inbound request). Some of these requests are known in advance. Some requests are dynamic in the sense that they appear during the day without any prior information. Finally, some inbound requests are stochastic. More precisely, with a certain probability each outbound request causes a corresponding inbound request on the same day. Some stochastic information about these return transports is available from historical data. The purpose of this study is to investigate, whether using this information in designing the routes has a significant positive effect on the solution quality. The problem is modeled as a dynamic stochastic dial-a-ride problem with expected return transports. We propose four different modifications of metaheuristic solution approaches for this problem. In detail, we test dynamic versions of variable neighborhood search (VNS) and stochastic VNS (S-VNS) as well as modified versions of the multiple plan approach (MPA) and the multiple scenario approach (MSA). Tests are performed using 12 sets of test instances based on a real road network. Various demand scenarios are generated based on the available real data. Results show that using the stochastic information on return transports leads to average improvements of around 15%. Moreover, improvements of up to 41% can be achieved for some test instances.

ASTRONAUT COOPER, GORDON L. - MERCURY-ATLAS (MA)-9 - PRELAUNCH - PREFLIGHT CHECK - CAPE

NASA Image and Video Library

1963-05-01

S63-06129 (1963) --- Astronaut L. Gordon Cooper Jr., prime pilot for the Mercury-Atlas 9 (MA-9) mission, inside his Mercury spacecraft, runs through one of the numerous preflight checks surrounded by dials, switches, indicators and buttons. Photo credit: NASA

NONLINEAR-APPROXIMATION TECHNIQUE FOR DETERMINING VERTICAL OZONE-CONCENTRATION PROFILES WITH A DIFFERENTIAL-ABSORPTION LIDAR

EPA Science Inventory

A new technique is presented for the retrieval of ozone concentration profiles from backscattered signals obtained by a multi-wavelength differential-absorption lidar (DIAL). The technique makes it possible to reduce erroneous local fluctuations induced in the ozone-concentration...

Internet Connections: Understanding Your Access Options.

ERIC Educational Resources Information Center

Notess, Greg R.

1994-01-01

Describes levels of Internet connectivity, physical connections, and connection speeds. Compares options for connecting to the Internet, including terminal accounts, dial-up terminal accounts, direct connections through a local area network, and direct connections using SLIP (Serial Line Internet Protocol) or PPP (Point-to-Point Protocol). (eight…

46 CFR 520.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... basic ocean freight rate. BTA means the Commission's Bureau of Trade Analysis or its successor bureau... carriers which provides for the fixing of and adherence to uniform tariff rates, charges, practices and... via dial-up telecommunications or a network link and interacts with the carrier's or publisher's...

46 CFR 520.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... basic ocean freight rate. BTA means the Commission's Bureau of Trade Analysis or its successor bureau... carriers which provides for the fixing of and adherence to uniform tariff rates, charges, practices and... via dial-up telecommunications or a network link and interacts with the carrier's or publisher's...

46 CFR 520.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... basic ocean freight rate. BTA means the Commission's Bureau of Trade Analysis or its successor bureau... carriers which provides for the fixing of and adherence to uniform tariff rates, charges, practices and... via dial-up telecommunications or a network link and interacts with the carrier's or publisher's...

46 CFR 520.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... basic ocean freight rate. BTA means the Commission's Bureau of Trade Analysis or its successor bureau... carriers which provides for the fixing of and adherence to uniform tariff rates, charges, practices and... via dial-up telecommunications or a network link and interacts with the carrier's or publisher's...

46 CFR 520.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... basic ocean freight rate. BTA means the Commission's Bureau of Trade Analysis or its successor bureau... carriers which provides for the fixing of and adherence to uniform tariff rates, charges, practices and... via dial-up telecommunications or a network link and interacts with the carrier's or publisher's...

Promoting Trade Books to Libraries.

ERIC Educational Resources Information Center

Teguis, Ellen

1982-01-01

Discusses the role and functions of the library promotion director within a commercial publishing house, outlining in the process the responsibilities and activities of the library services director for a specific firm (Dial Press/Delacourte Press). The nature of book promotion for bookstores and libraries is described. (JL)

WebWatch.

ERIC Educational Resources Information Center

Nesbeitt, Sarah

1997-01-01

Numerous Web-based phone and address directories provide advantages over the white and yellow pages. Although many share a common database, each has features that set it apart: maps, suggested driving directions, and phone dialing. This article examines eight (Bigfoot, BigBook, BigYellow, Switchboard, Infospace, Contractjobs, InterNIC)…

The role of information communication technology (ICT) towards universal health coverage: the first steps of a telemedicine project in Ethiopia.

PubMed

Shiferaw, Fassil; Zolfo, Maria

2012-01-01

Eighty-five per cent of the Ethiopian population lives in remote areas, without access to modern health services. The limited health care budget, chronic shortage of health care workers and lack of incentives to retain those in remote areas further jeopardize the national health care delivery system. Recently, the application of information communication technology (ICT) to health care delivery and the use of telemedicine have raised hopes. This paper analyzes the challenges, failures and successes encountered in setting-up and implementing a telemedicine program in Ethiopia and provides possible recommendations for developing telemedicine strategies in countries with limited resources. Ten sites in Ethiopia were selected to participate in this pilot between 2004 and 2006 and twenty physicians, two per site, were trained in the use of a store and forward telemedicine system, using a dial-up internet connection. Teledermatology, teleradiology and telepathology were the chosen disciplines for the electronic referrals, across the selected ten sites. Telemedicine implementation does not depend only on technological factors, rather on e-government readiness, enabling policies, multisectoral involvement and capacity building processes. There is no perfect 'one size fits all' technology and the use of combined interoperable applications, according to the local context, is highly recommended. Telemedicine is still in a premature phase of development in Ethiopia and other sub-Saharan African countries, and it remains difficult to talk objectively about measurable impact of its use, even though it has demonstrated practical applicability beyond reasonable doubts.

Acousto-optic filtering of lidar signals

NASA Technical Reports Server (NTRS)

Kolarov, G.; Deleva, A.; Mitsev, TS.

1992-01-01

The predominant part of the noise in lidar receivers is created by the background radiation; therefore, one of the most important elements of the receiving optics is a spectrally selecting filter placed in front of the photodetector. Interference filters are usually used to transmit a given wavelength. Specific properties of the interference filters, such as simple design, reliability, small size, and large aperture, combined with high transmission coefficient and narrow spectral band, make them the preferred spectral device in many cases. However, problems arise in applications such as the Differential Absorption Lidar (DIAL) technique, where fast tuning within a wide spectral region is necessary. Tunable acousto-optical filters (TAOF), used recently in astrophysical observations to suppress the background radiation, can be employed with success in lidar sounding. They are attractive due to the possibility for fast spectral scanning with a narrow transmission band. The TAOF's advantages are fully evident in DIAL lidars where one must simultaneously receive signals at two laser frequencies.