Update on Common-Cause Failure Experience and Mitigation Practices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wood, Richard Thomas; Muhlheim, Michael David; Pullum, Laura L

2014-04-01

Experience in other industries has shown that digital technology can provide substantial benefits in terms of performance and reliability. However, the U.S. nuclear power industry has been slow to adopt the technology extensively in its instrumentation and control (I&C) applications because of inhibiting factors such as regulatory uncertainty, insufficient technological experience base, implementation complexity, limited availability of nuclear-qualified products and vendors, and inadequate definition of modernization cost recapture. Although there have been examples of digital technology usage in the nuclear power industry, challenges to the qualification of digital technology for high-integrity nuclear power plant (NPP) applications have severely constrained moremore » widespread progress in achieving the benefits that are possible through the transition to digital. The U.S. Department of Energy (DOE) Office of Nuclear Energy (NE) established the Advanced Sensors and Instrumentation (ASI) technology area under the Nuclear Energy Enabling Technologies (NEET) Program to coordinate the instrumentation and controls (I&C) research across DOE NE and to identify and lead efforts to address common needs. As part of the NEET ASI research program, the Digital Technology Qualification project was established. Under this project, the Oak Ridge National Laboratory (ORNL) is leading the investigation into mitigation of digital common-cause failure (CCF) vulnerabilities for nuclear-qualified applications. This technical report documents updated and expanded findings from research activities by ORNL. Specifically, the report describes CCF experience in the nuclear and nonnuclear industries, identifies the state of the practice for CCF mitigation through key examples, and presents conclusions from the determination of knowledge gaps.« less

Information collection and processing of dam distortion in digital reservoir system

NASA Astrophysics Data System (ADS)

Liang, Yong; Zhang, Chengming; Li, Yanling; Wu, Qiulan; Ge, Pingju

2007-06-01

The "digital reservoir" is usually understood as describing the whole reservoir with digital information technology to make it serve the human existence and development furthest. Strictly speaking, the "digital reservoir" is referred to describing vast information of the reservoir in different dimension and space-time by RS, GPS, GIS, telemetry, remote-control and virtual reality technology based on computer, multi-media, large-scale memory and wide-band networks technology for the human existence, development and daily work, life and entertainment. The core of "digital reservoir" is to realize the intelligence and visibility of vast information of the reservoir through computers and networks. The dam is main building of reservoir, whose safety concerns reservoir and people's safety. Safety monitoring is important way guaranteeing the dam's safety, which controls the dam's running through collecting the dam's information concerned and developing trend. Safety monitoring of the dam is the process from collection and processing of initial safety information to forming safety concept in the brain. The paper mainly researches information collection and processing of the dam by digital means.

The research of laser marking control technology

NASA Astrophysics Data System (ADS)

Zhang, Qiue; Zhang, Rong

2009-08-01

In the area of Laser marking, the general control method is insert control card to computer's mother board, it can not support hot swap, it is difficult to assemble or it. Moreover, the one marking system must to equip one computer. In the system marking, the computer can not to do the other things except to transmit marking digital information. Otherwise it can affect marking precision. Based on traditional control methods existed some problems, introduced marking graphic editing and digital processing by the computer finish, high-speed digital signal processor (DSP) control marking the whole process. The laser marking controller is mainly contain DSP2812, digital memorizer, DAC (digital analog converting) transform unit circuit, USB interface control circuit, man-machine interface circuit, and other logic control circuit. Download the marking information which is processed by computer to U disk, DSP read the information by USB interface on time, then processing it, adopt the DSP inter timer control the marking time sequence, output the scanner control signal by D/A parts. Apply the technology can realize marking offline, thereby reduce the product cost, increase the product efficiency. The system have good effect in actual unit markings, the marking speed is more quickly than PCI control card to 20 percent. It has application value in practicality.

Soft-Fault Detection Technologies Developed for Electrical Power Systems

NASA Technical Reports Server (NTRS)

Button, Robert M.

2004-01-01

The NASA Glenn Research Center, partner universities, and defense contractors are working to develop intelligent power management and distribution (PMAD) technologies for future spacecraft and launch vehicles. The goals are to provide higher performance (efficiency, transient response, and stability), higher fault tolerance, and higher reliability through the application of digital control and communication technologies. It is also expected that these technologies will eventually reduce the design, development, manufacturing, and integration costs for large, electrical power systems for space vehicles. The main focus of this research has been to incorporate digital control, communications, and intelligent algorithms into power electronic devices such as direct-current to direct-current (dc-dc) converters and protective switchgear. These technologies, in turn, will enable revolutionary changes in the way electrical power systems are designed, developed, configured, and integrated in aerospace vehicles and satellites. Initial successes in integrating modern, digital controllers have proven that transient response performance can be improved using advanced nonlinear control algorithms. One technology being developed includes the detection of "soft faults," those not typically covered by current systems in use today. Soft faults include arcing faults, corona discharge faults, and undetected leakage currents. Using digital control and advanced signal analysis algorithms, we have shown that it is possible to reliably detect arcing faults in high-voltage dc power distribution systems (see the preceding photograph). Another research effort has shown that low-level leakage faults and cable degradation can be detected by analyzing power system parameters over time. This additional fault detection capability will result in higher reliability for long-lived power systems such as reusable launch vehicles and space exploration missions.

Rethinking agency and medical adherence technology: applying Actor Network Theory to the case study of Digital Pills.

PubMed

Hurtado-de-Mendoza, Alejandra; Cabling, Mark L; Sheppard, Vanessa B

2015-12-01

Much literature surrounding medical technology and adherence posits that technology is a mechanism for social control. This assumes that the medical establishment can take away patients' agency. Although power relationships and social control can play a key role, medical technology can also serve as an agentive tool to be utilized. We (1) offer the alternative framework of Actor Network Theory to view medical technology, (2) discuss the literature on medication adherence and technology, (3) delve into the ramifications of looking at adherence as a network and (4) use Digital Pills as a case study of dispersed agency. © 2015 John Wiley & Sons Ltd.

Superconductor Digital-RF Receiver Systems

NASA Astrophysics Data System (ADS)

Mukhanov, Oleg A.; Kirichenko, Dmitri; Vernik, Igor V.; Filippov, Timur V.; Kirichenko, Alexander; Webber, Robert; Dotsenko, Vladimir; Talalaevskii, Andrei; Tang, Jia Cao; Sahu, Anubhav; Shevchenko, Pavel; Miller, Robert; Kaplan, Steven B.; Sarwana, Saad; Gupta, Deepnarayan

Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ˜30GHz clock frequencies.

The Effect of the Digital Classroom on Academic Success and Online Technologies Self-Efficacy

ERIC Educational Resources Information Center

Ozerbas, Mehmet Arif; Erdogan, Bilge Has

2016-01-01

This study aimed to observe whether the learning environment created by digital classroom technologies has any effect on the academic success and online technologies self-efficacy of 7th grade students. In this study, an experimental design with a pre-test/post-test control group was used. The research was conducted with 58 students in a secondary…

F-8 Iron Bird Cockpit

NASA Technical Reports Server (NTRS)

1975-01-01

The F-8 DFBW (Digital-Fly-By-Wire) simulator used an 'Iron-Bird' for its cockpit. It was used from 1971 to 1986. The F-8 DFBW simulator was used in the development, testing, and validation of an all digital flight-control system installed in the F-8 aircraft that replaced the normal mechanical/hydraulic controls. Many military and commercial aircraft have digital flight control systems based on the technologies developed at NASA Dryden.

Micro-electro-mechanical systems (MEMS) and agile lensing-based modules for communications, sensing and signal processing

NASA Astrophysics Data System (ADS)

Reza, Syed Azer

This dissertation proposes the use of the emerging Micro-Electro-Mechanical Systems (MEMS) and agile lensing optical device technologies to design novel and powerful signal conditioning and sensing modules for advanced applications in optical communications, physical parameter sensing and RF/optical signal processing. For example, these new module designs have experimentally demonstrated exceptional features such as stable loss broadband operations and high > 60 dB optical dynamic range signal filtering capabilities. The first part of the dissertation describes the design and demonstration of digital MEMS-based signal processing modules for communication systems and sensor networks using the TI DLP (Digital Light Processing) technology. Examples of such modules include optical power splitters, narrowband and broadband variable fiber optical attenuators, spectral shapers and filters. Compared to prior works, these all-digital designs have advantages of repeatability, accuracy, and reliability that are essential for advanced communications and sensor applications. The next part of the dissertation proposes, analyzes and demonstrates the use of analog opto-fluidic agile lensing technology for sensor networks and test and measurement systems. Novel optical module designs for distance sensing, liquid level sensing, three-dimensional object shape sensing and variable photonic delay lines are presented and experimentally demonstrated. Compared to prior art module designs, the proposed analog-mode modules have exceptional performances, particularly for extreme environments (e.g., caustic liquids) where the free-space agile beam-based sensor provide remote non-contact access for physical sensing operations. The dissertation also presents novel modules involving hybrid analog-digital photonic designs that make use of the different optical device technologies to deliver the best features of both analog and digital optical device operations and controls. Digital controls are achieved through the use of the digital MEMS technology and analog controls are realized by employing opto-fluidic agile lensing technology and acousto-optic technology. For example, variable fiber-optic attenuators and spectral filters are proposed using the hybrid design. Compared to prior art module designs, these hybrid designs provide a higher module dynamic range and increased resolution that are critical in various advanced system applications. In summary, the dissertation shows the added power of hybrid optical designs using both the digital and analog photonic signal processing versus just all-digital or all-analog module designs.

Access control based on attribute certificates for medical intranet applications.

PubMed

Mavridis, I; Georgiadis, C; Pangalos, G; Khair, M

2001-01-01

Clinical information systems frequently use intranet and Internet technologies. However these technologies have emphasized sharing and not security, despite the sensitive and private nature of much health information. Digital certificates (electronic documents which recognize an entity or its attributes) can be used to control access in clinical intranet applications. To outline the need for access control in distributed clinical database systems, to describe the use of digital certificates and security policies, and to propose the architecture for a system using digital certificates, cryptography and security policy to control access to clinical intranet applications. We have previously developed a security policy, DIMEDAC (Distributed Medical Database Access Control), which is compatible with emerging public key and privilege management infrastructure. In our implementation approach we propose the use of digital certificates, to be used in conjunction with DIMEDAC. Our proposed access control system consists of two phases: the ways users gain their security credentials; and how these credentials are used to access medical data. Three types of digital certificates are used: identity certificates for authentication; attribute certificates for authorization; and access-rule certificates for propagation of access control policy. Once a user is identified and authenticated, subsequent access decisions are based on a combination of identity and attribute certificates, with access-rule certificates providing the policy framework. Access control in clinical intranet applications can be successfully and securely managed through the use of digital certificates and the DIMEDAC security policy.

Flight control systems development of highly maneuverable aircraft technology /HiMAT/ vehicle

NASA Technical Reports Server (NTRS)

Petersen, K. L.

1979-01-01

The highly maneuverable aircraft technology (HiMAT) program was conceived to demonstrate advanced technology concepts through scaled-aircraft flight tests using a remotely piloted technique. Closed-loop primary flight control is performed from a ground-based cockpit, utilizing a digital computer and up/down telemetry links. A backup flight control system for emergency operation resides in an onboard computer. The onboard systems are designed to provide fail-operational capabilities and utilize two microcomputers, dual uplink receiver/decoders, and redundant hydraulic actuation and power systems. This paper discusses the design and validation of the primary and backup digital flight control systems as well as the unique pilot and specialized systems interfaces.

Machine vision for digital microfluidics

NASA Astrophysics Data System (ADS)

Shin, Yong-Jun; Lee, Jeong-Bong

2010-01-01

Machine vision is widely used in an industrial environment today. It can perform various tasks, such as inspecting and controlling production processes, that may require humanlike intelligence. The importance of imaging technology for biological research or medical diagnosis is greater than ever. For example, fluorescent reporter imaging enables scientists to study the dynamics of gene networks with high spatial and temporal resolution. Such high-throughput imaging is increasingly demanding the use of machine vision for real-time analysis and control. Digital microfluidics is a relatively new technology with expectations of becoming a true lab-on-a-chip platform. Utilizing digital microfluidics, only small amounts of biological samples are required and the experimental procedures can be automatically controlled. There is a strong need for the development of a digital microfluidics system integrated with machine vision for innovative biological research today. In this paper, we show how machine vision can be applied to digital microfluidics by demonstrating two applications: machine vision-based measurement of the kinetics of biomolecular interactions and machine vision-based droplet motion control. It is expected that digital microfluidics-based machine vision system will add intelligence and automation to high-throughput biological imaging in the future.

Highly integrated digital electronic control: Digital flight control, aircraft model identification, and adaptive engine control

NASA Technical Reports Server (NTRS)

Baer-Riedhart, Jennifer L.; Landy, Robert J.

1987-01-01

The highly integrated digital electronic control (HIDEC) program at NASA Ames Research Center, Dryden Flight Research Facility is a multiphase flight research program to quantify the benefits of promising integrated control systems. McDonnell Aircraft Company is the prime contractor, with United Technologies Pratt and Whitney Aircraft, and Lear Siegler Incorporated as major subcontractors. The NASA F-15A testbed aircraft was modified by the HIDEC program by installing a digital electronic flight control system (DEFCS) and replacing the standard F100 (Arab 3) engines with F100 engine model derivative (EMD) engines equipped with digital electronic engine controls (DEEC), and integrating the DEEC's and DEFCS. The modified aircraft provides the capability for testing many integrated control modes involving the flight controls, engine controls, and inlet controls. This paper focuses on the first two phases of the HIDEC program, which are the digital flight control system/aircraft model identification (DEFCS/AMI) phase and the adaptive engine control system (ADECS) phase.

Status of Optical Disk Standards and Copy Protection Technology

DTIC Science & Technology

2000-01-01

Technology (IT), the Consumer Electronics (CE) and the Content Providers such as the Motion Picture Association (MPA) and Secure Digital Music ...and Access Control. On audio recording, Secure Digital Music Initiative (SDMI) is leading the effort. 10 Besides these organizations, a world wide...coordinating orgainzation which ia working with the Information Technology Inductry Association (ITI), the Content Providers such as the Motion Picture

Migration of Older to New Digital Control Systems in Nuclear Power Plant Main Control Rooms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kovesdi, Casey Robert; Joe, Jeffrey Clark

The United States (U.S.) Department of Energy (DOE) Office of Nuclear Energy (NE) has the primary mission to advance nuclear power by resolving socio-technical issues through research and development (R&D). One DOE-NE activity supporting this mission is the Light Water Reactor Sustainability (LWRS) program. LWRS has the overall objective to sustain the operation of existing commercial nuclear power plants (NPPs) through conducting R&D across multiple “pathways,” or R&D focus areas. The Advanced Instrumentation, Information, and Control (II&C) Systems Technologies pathway conducts targeted R&D to address aging and reliability concerns with the legacy instrumentation and control (I&C) and related information systemsmore » in operating U.S. NPPs. This work involves (1) ensuring that legacy analog II&C systems are not life-limiting issues for the LWR fleet, and (2) implementing digital II&C technology in a manner that enables broad innovation and business improvement in the NPP operating model. Under the LWRS Advanced II&C pathway, Human Factors experts at Idaho National Laboratory (INL) have been conducting R&D in support of NPP main control room (MCR) modernization activities. Work in prior years has focused on migrating analog I&C systems to new digital I&C systems (). In fiscal year 2016 (FY16), one new focus area for this research is migrating older digital I&C systems to new and advanced digital I&C systems. This report summarizes a plan for conducting a digital-to-digital migration of a legacy digital I&C system to a new digital I&C system in support of control room modernization activities.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Kenneth; Oxstrand, Johanna

The Digital Architecture effort is a part of the Department of Energy (DOE) sponsored Light-Water Reactor Sustainability (LWRS) Program conducted at Idaho National Laboratory (INL). The LWRS program is performed in close collaboration with industry research and development (R&D) programs that provides the technical foundations for licensing and managing the long-term, safe, and economical operation of current nuclear power plants (NPPs). One of the primary missions of the LWRS program is to help the U.S. nuclear industry adopt new technologies and engineering solutions that facilitate the continued safe operation of the plants and extension of the current operating licenses. Therefore,more » a major objective of the LWRS program is the development of a seamless digital environment for plant operations and support by integrating information from plant systems with plant processes for nuclear workers through an array of interconnected technologies. In order to get the most benefits of the advanced technology suggested by the different research activities in the LWRS program, the nuclear utilities need a digital architecture in place to support the technology. A digital architecture can be defined as a collection of information technology (IT) capabilities needed to support and integrate a wide-spectrum of real-time digital capabilities for nuclear power plant performance improvements. It is not hard to imagine that many processes within the plant can be largely improved from both a system and human performance perspective by utilizing a plant wide (or near plant wide) wireless network. For example, a plant wide wireless network allows for real time plant status information to easily be accessed in the control room, field workers’ computer-based procedures can be updated based on the real time plant status, and status on ongoing procedures can be incorporated into smart schedules in the outage command center to allow for more accurate planning of critical tasks. The goal of the digital architecture project is to provide a long-term strategy to integrate plant systems, plant processes, and plant workers. This include technologies to improve nuclear worker efficiency and human performance; to offset a range of plant surveillance and testing activities with new on-line monitoring technologies; improve command, control, and collaboration in settings such as outage control centers and work execution centers; and finally to improve operator performance with new operator aid technologies for the control room. The requirements identified through the activities in the Digital Architecture project will be used to estimate the amount of traffic on the network and hence estimating the minimal bandwidth needed.« less

Access Control based on Attribute Certificates for Medical Intranet Applications

PubMed Central

Georgiadis, Christos; Pangalos, George; Khair, Marie

2001-01-01

Background Clinical information systems frequently use intranet and Internet technologies. However these technologies have emphasized sharing and not security, despite the sensitive and private nature of much health information. Digital certificates (electronic documents which recognize an entity or its attributes) can be used to control access in clinical intranet applications. Objectives To outline the need for access control in distributed clinical database systems, to describe the use of digital certificates and security policies, and to propose the architecture for a system using digital certificates, cryptography and security policy to control access to clinical intranet applications. Methods We have previously developed a security policy, DIMEDAC (Distributed Medical Database Access Control), which is compatible with emerging public key and privilege management infrastructure. In our implementation approach we propose the use of digital certificates, to be used in conjunction with DIMEDAC. Results Our proposed access control system consists of two phases: the ways users gain their security credentials; and how these credentials are used to access medical data. Three types of digital certificates are used: identity certificates for authentication; attribute certificates for authorization; and access-rule certificates for propagation of access control policy. Once a user is identified and authenticated, subsequent access decisions are based on a combination of identity and attribute certificates, with access-rule certificates providing the policy framework. Conclusions Access control in clinical intranet applications can be successfully and securely managed through the use of digital certificates and the DIMEDAC security policy. PMID:11720951

Image Acquisition and Quality in Digital Radiography.

PubMed

Alexander, Shannon

2016-09-01

Medical imaging has undergone dramatic changes and technological breakthroughs since the introduction of digital radiography. This article presents information on the development of digital radiography and types of digital radiography systems. Aspects of image quality and radiation exposure control are highlighted as well. In addition, the article includes related workplace changes and medicolegal considerations in the digital radiography environment. ©2016 American Society of Radiologic Technologists.

Evaluation of Digital Technology and Software Use among Business Education Teachers

ERIC Educational Resources Information Center

Ellis, Richard S.; Okpala, Comfort O.

2004-01-01

Digital video cameras are part of the evolution of multimedia digital products that have positive applications for educators, students, and industry. Multimedia digital video can be utilized by any personal computer and it allows the user to control, combine, and manipulate different types of media, such as text, sound, video, computer graphics,…

Digital Electronic Engine Control (DEEC) Flight Evaluation in an F-15 Airplane

NASA Technical Reports Server (NTRS)

1984-01-01

Flight evaluation in an F-15 aircraft by digital electronic engine control (DEEC) was investigated. Topics discussed include: system description, F100 engine tests, effects of inlet distortion on static pressure probe, flight tests, digital electronic engine control fault detection and accommodation flight evaluation, flight evaluation of a hydromechanical backup control, augmentor transient capability of an F100 engine, investigation of nozzle instability, real time in flight thrust calculation, and control technology for future aircraft propulsion systems. It is shown that the DEEC system is a powerful and flexible controller for the F100 engine.

Qualification of the flight-critical AFTI/F-16 digital flight control system. [Advanced Fighter Technology Integration

NASA Technical Reports Server (NTRS)

Mackall, D. A.; Ishmael, S. D.; Regenie, V. A.

1983-01-01

Qualification considerations for assuring the safety of a life-critical digital flight control system include four major areas: systems interactions, verification, validation, and configuration control. The AFTI/F-16 design, development, and qualification illustrate these considerations. In this paper, qualification concepts, procedures, and methodologies are discussed and illustrated through specific examples.

Simulation of proportional control of hydraulic actuator using digital hydraulic valves

NASA Astrophysics Data System (ADS)

Raghuraman, D. R. S.; Senthil Kumar, S.; Kalaiarasan, G.

2017-11-01

Fluid power systems using oil hydraulics in earth moving and construction equipment have been using proportional and servo control valves for a long time to achieve precise and accurate position control backed by system performance. Such valves are having feedback control in them and exhibit good response, sensitivity and fine control of the actuators. Servo valves and proportional valves are possessing less hysteresis when compared to on-off type valves, but when the servo valve spools get stuck in one position, a high frequency called as jitter is employed to bring the spool back, whereas in on-off type valves it requires lesser technology to retract the spool. Hence on-off type valves are used in a technology known as digital valve technology, which caters to precise control on slow moving loads with fast switching times and with good flow and pressure control mimicking the performance of an equivalent “proportional valve” or “servo valve”.

Propulsion system-flight control integration-flight evaluation and technology transition

NASA Technical Reports Server (NTRS)

Burcham, Frank W., Jr.; Gilyard, Glenn B.; Myers, Lawrence P.

1990-01-01

Integration of propulsion and flight control systems and their optimization offering significant performance improvement are assessed. In particular, research programs conducted by NASA on flight control systems and propulsion system-flight control interactions on the YF-12 and F-15 aircraft are addressed; these programs have demonstrated increased thrust, reduced fuel consumption, increased engine life, and improved aircraft performance. Focus is placed on altitude control, speed-Mach control, integrated controller design, as well as flight control systems and digital electronic engine control. A highly integrated digital electronic control program is analyzed and compared with a performance seeking control program. It is shown that the flight evaluation and demonstration of these technologies have been a key part in the transition of the concepts to production and operational use on a timely basis.

Application of Integration of HBIM and VR Technology to 3D Immersive Digital Management—Take Han Type Traditional Architecture as an Example

NASA Astrophysics Data System (ADS)

Lin, Y.-C.

2017-08-01

HBIM technology makes great contributions to 3D digital preservation and management of the existing traditional architectures, and VR technology has also been gradually emphasized by 3D users in recent years, especially 3D immersive situation makes users more likely to experience the real space field. Taking Han type traditional architecture with relatively complex geometrical structure as an example, this research carries out digital preservation through HBIM technology and tries to switch to VR platform to allow users to enter 3D immersive scene for management and display. It is shown in the research results that the application of integration of HBIM and VR technology to Han type traditional architecture needs to consider 3D digital model of the architecture, and the number of polygon shall be controlled below about 2 million, which can make the operation in VR environment more smooth; the integration of two technologies can achieve the purpose of 3D immersive digital management, which can provide the humanized application close to the real experience for the display of subsequent management of ancient relics and architectural aesthetics.

A HUMAN FACTORS ENGINEERING PROCESS TO SUPPORT HUMAN-SYSTEM INTERFACE DESIGN IN CONTROL ROOM MODERNIZATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kovesdi, C.; Joe, J.; Boring, R.

The primary objective of the United States (U.S.) Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) program is to sustain operation of the existing commercial nuclear power plants (NPPs) through a multi-pathway approach in conducting research and development (R&D). The Advanced Instrumentation, Information, and Control (II&C) System Technologies pathway conducts targeted R&D to address aging and reliability concerns with legacy instrumentation and control (I&C) and other information systems in existing U.S. NPPs. Control room modernization is an important part following this pathway, and human factors experts at Idaho National Laboratory (INL) have been involved in conducting R&D to supportmore » migration of new digital main control room (MCR) technologies from legacy analog and legacy digital I&C. This paper describes a human factors engineering (HFE) process that supports human-system interface (HSI) design in MCR modernization activities, particularly with migration of old digital to new digital I&C. The process described in this work is an expansion from the LWRS Report INL/EXT-16-38576, and is a requirements-driven approach that aligns with NUREG-0711 requirements. The work described builds upon the existing literature by adding more detail around key tasks and decisions to make when transitioning from HSI Design into Verification and Validation (V&V). The overall objective of this process is to inform HSI design and elicit specific, measurable, and achievable human factors criteria for new digital technologies. Upon following this process, utilities should have greater confidence with transitioning from HSI design into V&V.« less

Examining the Impact of Off-Task Multi-Tasking with Technology on Real-Time Classroom Learning

ERIC Educational Resources Information Center

Wood, Eileen; Zivcakova, Lucia; Gentile, Petrice; Archer, Karin; De Pasquale, Domenica; Nosko, Amanda

2012-01-01

The purpose of the present study was to examine the impact of multi-tasking with digital technologies while attempting to learn from real-time classroom lectures in a university setting. Four digitally-based multi-tasking activities (texting using a cell-phone, emailing, MSN messaging and Facebook[TM]) were compared to 3 control groups…

Effect of Computer-Assisted Learning on Students' Dental Anatomy Waxing Performance.

PubMed

Kwon, So Ran; Hernández, Marcela; Blanchette, Derek R; Lam, Matthew T; Gratton, David G; Aquilino, Steven A

2015-09-01

The aim of this study was to evaluate the impact of computer-assisted learning on first-year dental students' waxing abilities and self-evaluation skills. Additionally, this study sought to determine how well digital evaluation software performed compared to faculty grading with respect to students' technical scores on a practical competency examination. First-year students at one U.S. dental school were assigned to one of three groups: control (n=40), E4D Compare (n=20), and Sirona prepCheck (n=19). Students in the control group were taught by traditional teaching methodologies, and the technology-assisted groups received both traditional training and supplementary feedback from the corresponding digital system. Five outcomes were measured: visual assessment score, self-evaluation score, and digital assessment scores at 0.25 mm, 0.30 mm, and 0.35 mm tolerance. The scores from visual assessment and self-evaluation were examined for differences among groups using the Kruskal-Wallis test. Correlation between the visual assessment and digital scores was measured using Pearson and Spearman rank correlation coefficients. At completion of the course, students were asked to complete a survey on the use of these digital technologies. All 79 students in the first-year class participated in the study, for a 100% response rate. The results showed that the visual assessment and self-evaluation scores did not differ among groups (p>0.05). Overall correlations between visual and digital assessment scores were modest though statistically significant (5% level of significance). Analysis of survey responses completed by students in the technology groups showed that profiles for the two groups were similar and not favorable towards digital technology. The study concluded that technology-assisted training did not affect these students' waxing performance or self-evaluation skills and that visual scores given by faculty and digital assessment scores correlated moderately.

[Chinese medicine industry 4.0：advancing digital pharmaceutical manufacture toward intelligent pharmaceutical manufacture].

PubMed

Cheng, Yi-Yu; Qu, Hai-Bin; Zhang, Bo-Li

2016-01-01

A perspective analysis on the technological innovation in pharmaceutical engineering of Chinese medicine unveils a vision on "Future Factory" of Chinese medicine industry in mind. The strategy as well as the technical roadmap of "Chinese medicine industry 4.0" is proposed, with the projection of related core technology system. It is clarified that the technical development path of Chinese medicine industry from digital manufacture to intelligent manufacture. On the basis of precisely defining technical terms such as process control, on-line detection and process quality monitoring for Chinese medicine manufacture, the technical concepts and characteristics of intelligent pharmaceutical manufacture as well as digital pharmaceutical manufacture are elaborated. Promoting wide applications of digital manufacturing technology of Chinese medicine is strongly recommended. Through completely informationized manufacturing processes and multi-discipline cluster innovation, intelligent manufacturing technology of Chinese medicine should be developed, which would provide a new driving force for Chinese medicine industry in technology upgrade, product quality enhancement and efficiency improvement. Copyright© by the Chinese Pharmaceutical Association.

Investigation of the impact of main control room digitalization on operators cognitive reliability in nuclear power plants.

PubMed

Zhou, Yong; Mu, Haiying; Jiang, Jianjun; Zhang, Li

2012-01-01

Currently, there is a trend in nuclear power plants (NPPs) toward introducing digital and computer technologies into main control rooms (MCRs). Safe generation of electric power in NPPs requires reliable performance of cognitive tasks such as fault detection, diagnosis, and response planning. The digitalization of MCRs has dramatically changed the whole operating environment, and the ways operators interact with the plant systems. If the design and implementation of the digital technology is incompatible with operators' cognitive characteristics, it may have negative effects on operators' cognitive reliability. Firstly, on the basis of three essential prerequisites for successful cognitive tasks, a causal model is constructed to reveal the typical human performance issues arising from digitalization. The cognitive mechanisms which they impact cognitive reliability are analyzed in detail. Then, Bayesian inference is used to quantify and prioritize the influences of these factors. It suggests that interface management and unbalanced workload distribution have more significant impacts on operators' cognitive reliability.

Optics and optics-based technologies education with the benefit of LabVIEW

NASA Astrophysics Data System (ADS)

Wan, Yuhong; Man, Tianlong; Tao, Shiquan

2015-10-01

The details of design and implementation of incoherent digital holographic experiments based on LabVIEW are demonstrated in this work in order to offer a teaching modal by making full use of LabVIEW as an educational tool. Digital incoherent holography enables holograms to be recorded from incoherent light with just a digital camera and spatial light modulator and three-dimensional properties of the specimen are revealed after the hologram is reconstructed in the computer. The experiment of phase shifting incoherent digital holography is designed and implemented based on the principle of Fresnel incoherent correlation holography. An automatic control application is developed based on LabVIEW, which combines the functions of major experimental hardware control and digital reconstruction of the holograms. The basic functions of the system are completed and a user-friendly interface is provided for easy operation. The students are encouraged and stimulated to learn and practice the basic principle of incoherent digital holography and other related optics-based technologies during the programming of the application and implementation of the system.

Digital Earth system based river basin data integration

NASA Astrophysics Data System (ADS)

Zhang, Xin; Li, Wanqing; Lin, Chao

2014-12-01

Digital Earth is an integrated approach to build scientific infrastructure. The Digital Earth systems provide a three-dimensional visualization and integration platform for river basin data which include the management data, in situ observation data, remote sensing observation data and model output data. This paper studies the Digital Earth system based river basin data integration technology. Firstly, the construction of the Digital Earth based three-dimensional river basin data integration environment is discussed. Then the river basin management data integration technology is presented which is realized by general database access interface, web service and ActiveX control. Thirdly, the in situ data stored in database tables as records integration is realized with three-dimensional model of the corresponding observation apparatus display in the Digital Earth system by a same ID code. In the next two parts, the remote sensing data and the model output data integration technologies are discussed in detail. The application in the Digital Zhang River basin System of China shows that the method can effectively improve the using efficiency and visualization effect of the data.

Developing an Integration Infrastructure for Distributed Engine Control Technologies

NASA Technical Reports Server (NTRS)

Culley, Dennis; Zinnecker, Alicia; Aretskin-Hariton, Eliot; Kratz, Jonathan

2014-01-01

Turbine engine control technology is poised to make the first revolutionary leap forward since the advent of full authority digital engine control in the mid-1980s. This change aims squarely at overcoming the physical constraints that have historically limited control system hardware on aero-engines to a federated architecture. Distributed control architecture allows complex analog interfaces existing between system elements and the control unit to be replaced by standardized digital interfaces. Embedded processing, enabled by high temperature electronics, provides for digitization of signals at the source and network communications resulting in a modular system at the hardware level. While this scheme simplifies the physical integration of the system, its complexity appears in other ways. In fact, integration now becomes a shared responsibility among suppliers and system integrators. While these are the most obvious changes, there are additional concerns about performance, reliability, and failure modes due to distributed architecture that warrant detailed study. This paper describes the development of a new facility intended to address the many challenges of the underlying technologies of distributed control. The facility is capable of performing both simulation and hardware studies ranging from component to system level complexity. Its modular and hierarchical structure allows the user to focus their interaction on specific areas of interest.

Towards a Standard Mixed-Signal Parallel Processing Architecture for Miniature and Microrobotics.

PubMed

Sadler, Brian M; Hoyos, Sebastian

2014-01-01

The conventional analog-to-digital conversion (ADC) and digital signal processing (DSP) architecture has led to major advances in miniature and micro-systems technology over the past several decades. The outlook for these systems is significantly enhanced by advances in sensing, signal processing, communications and control, and the combination of these technologies enables autonomous robotics on the miniature to micro scales. In this article we look at trends in the combination of analog and digital (mixed-signal) processing, and consider a generalized sampling architecture. Employing a parallel analog basis expansion of the input signal, this scalable approach is adaptable and reconfigurable, and is suitable for a large variety of current and future applications in networking, perception, cognition, and control.

Towards a Standard Mixed-Signal Parallel Processing Architecture for Miniature and Microrobotics

PubMed Central

Sadler, Brian M; Hoyos, Sebastian

2014-01-01

The conventional analog-to-digital conversion (ADC) and digital signal processing (DSP) architecture has led to major advances in miniature and micro-systems technology over the past several decades. The outlook for these systems is significantly enhanced by advances in sensing, signal processing, communications and control, and the combination of these technologies enables autonomous robotics on the miniature to micro scales. In this article we look at trends in the combination of analog and digital (mixed-signal) processing, and consider a generalized sampling architecture. Employing a parallel analog basis expansion of the input signal, this scalable approach is adaptable and reconfigurable, and is suitable for a large variety of current and future applications in networking, perception, cognition, and control. PMID:26601042

Guidance, Navigation and Control Digital Emulation Technology Laboratory. Volume 1. Part 1. Task 1: Digital Emulation Technology Laboratory

DTIC Science & Technology

1991-09-27

complex floating-point functions in a fraction of the time used by the best supercomputers on the market today. These co-processing boards "piggy-back...by the VNIX-based DECLARE program. Ve’ ctLptieu du te, tedi the new verion with main programs that noi, include onlN the variablc required wkith each

The trend of digital control system design for nuclear power plants in Korea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, S. H.; Jung, H. Y.; Yang, C. Y.

2006-07-01

Currently there are 20 nuclear power plants (NPPs) in operation, and 6 more units are under construction in Korea. The control systems of those NPPs have also been developed together with the technology advancement. Control systems started with On-Off control using the relay logic, had been evolved into Solid-State logic using TTL ICs, and applied with the micro-processors since the Yonggwang NPP Units 3 and 4 which started its construction in 1989. Multiplexers are also installed at the local plant areas to collect field input and to send output signals while communicating with the controllers located in the system cabinetsmore » near the main control room in order to reduce the field wiring cables. The design of the digital control system technology for the NPPs in Korea has been optimized to maximize the operability as well as the safety through the design, construction, start-up and operation experiences. Both Shin-Kori Units 1 and 2 and Shin-Wolsong Units 1 and 2 NPP projects under construction are being progressed at the same time. Digital Plant Control Systems of these projects have adopted multi-loop controllers, redundant loop configuration, and soft control system for the radwaste system. Programmable Logic Controller (PLC) and Distributed Control System (DCS) are applied with soft control system in Shin-Kori Units 3 and 4. This paper describes the evolvement of control system at the NPPs in Korea and the experience and design improvement through the observation of the latest failure of the digital control system. In addition, design concept and its trend of the digital control system being applied to the NPP in Korea are introduced. (authors)« less

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study

NASA Technical Reports Server (NTRS)

1982-01-01

The Current and Advanced Technology ACT control system definition tasks of the Integrated Application of Active Controls (IAAC) Technology project within the Energy Efficient Transport Program are summarized. The systems mechanize six active control functions: (1) pitch augmented stability; (2) angle of attack limiting; (3) lateral/directional augmented stability; (4) gust load alleviation; (5) maneuver load control; and (6) flutter mode control. The redundant digital control systems meet all function requirements with required reliability and declining weight and cost as advanced technology is introduced.

Digital poly-victimization: The increasing importance of online crime and harassment to the burden of victimization.

PubMed

Hamby, Sherry; Blount, Zach; Smith, Alli; Jones, Lisa; Mitchell, Kimberly; Taylor, Elizabeth

2018-01-01

Many forms of victimization, including bullying and property crime, are increasingly moving online, but most studies of poly-victimization still primarily focus on in-person crime and violence. Few studies have examined the importance of incorporating technology-based victimizations for assessing the true burden of violence. The purpose of this study is to explore whether digital poly-victimization contributes to post-traumatic stress and anxiety/dysphoria symptoms after controlling for in-person poly-victimization. Given that technology use and technology-based victimization are changing rapidly, a mixed methods approach was adopted. In the first two phases, focus groups and cognitive interviews (89 total participants) were used to identify the range of digital victimization and develop the Digital Poly-Victimization Scale. In the third phase, the new measure was included in a community survey (n = 478, 57.5% female; 62.6% earning under $50,000 per year) in a rural Southern region, along with measures of in-person poly-victimization, posttraumatic stress and anxiety/dysphoria symptoms, and other outcomes and personal characteristics. A comprehensive measure of digital poly-victimization indicated that almost 3 in 4 participants (72.3%) had experienced at least one form of digital victimization. The results indicated that digital poly-victimization contributed unique variance to post-traumatic stress and anxiety/dysphoria symptoms (p < .001), health-related quality of life (p < .01), and subjective and family well-being (both p < .001), even after controlling for demographics and in-person poly-victimization. Digital victimization often presents fewer risks to perpetrators and can be expected to represent an increasing share of the societal burden of violence. Future research on poly-victimization should pay more attention to the role of digital victimization.

Construct mine environment monitoring system based on wireless mesh network

NASA Astrophysics Data System (ADS)

Chen, Xin; Ge, Gengyu; Liu, Yinmei; Cheng, Aimin; Wu, Jun; Fu, Jun

2018-04-01

The system uses wireless Mesh network as a network transmission medium, and strive to establish an effective and reliable underground environment monitoring system. The system combines wireless network technology and embedded technology to monitor the internal data collected in the mine and send it to the processing center for analysis and environmental assessment. The system can be divided into two parts: the main control network module and the data acquisition terminal, and the SPI bus technology is used for mutual communication between them. Multi-channel acquisition and control interface design Data acquisition and control terminal in the analog signal acquisition module, digital signal acquisition module, and digital signal output module. The main control network module running Linux operating system, in which the transplant SPI driver, USB card driver and AODV routing protocol. As a result, the internal data collection and reporting of the mine are realized.

Light Water Reactor Sustainability Program Advanced Instrumentation, Information, and Control Systems Technologies Technical Program Plan for FY 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hallbert, Bruce Perry; Thomas, Kenneth David

2015-10-01

Reliable instrumentation, information, and control (II&C) systems technologies are essential to ensuring safe and efficient operation of the U.S. light water reactor (LWR) fleet. These technologies affect every aspect of nuclear power plant (NPP) and balance-of-plant operations. In 1997, the National Research Council conducted a study concerning the challenges involved in modernization of digital instrumentation and control systems in NPPs. Their findings identified the need for new II&C technology integration.

Human-In-The-Loop Simulation in Support of Long-Term Sustainability of Light Water Reactors

DOE PAGES

Hallbert, Bruce P

2015-01-01

Reliable instrumentation, information, and control systems technologies are essential to ensuring safe and efficient operation of the U.S. light water reactor (LWR) fleet. These technologies affect every aspect of nuclear power plant (NPP) and balance-of-plant operations. In 1997, the National Research Council conducted a study concerning the challenges involved in modernization of digital instrumentation and control systems in NPPs. Their findings identified the need for new II&C technology integration. The NPP owners and operators realize that this analog technology represents a significant challenge to sustaining the operation of the current fleet of NPPs. Beyond control systems, new technologies are neededmore » to monitor and characterize the effects of aging and degradation in critical areas of key structures, systems, and components. The objective of the efforts sponsored by the U.S. Department of Energy is to develop, demonstrate, and deploy new digital technologies for II&C architectures and provide monitoring capabilities to ensure the continued safe, reliable, and economic operation of the nation’s NPPs.« less

Space shuttle avionics system

NASA Technical Reports Server (NTRS)

Hanaway, John F.; Moorehead, Robert W.

1989-01-01

The Space Shuttle avionics system, which was conceived in the early 1970's and became operational in the 1980's represents a significant advancement of avionics system technology in the areas of systems and redundacy management, digital data base technology, flight software, flight control integration, digital fly-by-wire technology, crew display interface, and operational concepts. The origins and the evolution of the system are traced; the requirements, the constraints, and other factors which led to the final configuration are outlined; and the functional operation of the system is described. An overall system block diagram is included.

Tablet PC interaction with digital micromirror device (DMD)

NASA Astrophysics Data System (ADS)

Refai, Hakki H.; Dahshan, Mostafa H.; Sluss, James J., Jr.

2007-02-01

Digital light processing (DLP) is an innovative display technology that uses an optical switch array, known as a digital micromirror device (DMD), which allows digital control of light. To date, DMDs have been used primarily as high-speed spatial light modulators for projector applications. A tablet PC is a notebook or slate-shaped mobile PC. Its touch screen or digitizing tablet technology allows the user to operate the notebook with a stylus or digital pen instead of using a keyboard or mouse. In this paper, we describe an interface solution that translates any sketch on the tablet PC screen to an identical mirror-copy over the cross-section of the DMD micromirrors such that the image of the sketch can be projected onto a special screen. An algorithm has been created to control each single micromirror of the hundreds of thousands of micromirrors that cover the DMD surface. We demonstrate the successful application of a DMD to a high-speed two-dimensional (2D) scanning environment, acquiring the data from the tablet screen and launching its contents to the projection screen; with very high accuracy up to 13.68 μm x 13.68 μm of mirror pitch.

Journalistic Skills in the Digitalized Newsroom.

ERIC Educational Resources Information Center

Christopher, L. Carol

This paper explores three different implementations of technology in newsrooms: electronic editing, pagination, and computer-assisted reporting. Also examined are the ways in which newspapers are using newsroom technology both to gain greater control over the content and appearance of the newspaper and to gain greater control over the labor…

Development of Protection and Control Unit for Distribution Substation

NASA Astrophysics Data System (ADS)

Iguchi, Fumiaki; Hayashi, Hideyuki; Takeuchi, Motohiro; Kido, Mitsuyasu; Kobayashi, Takashi; Yanaoka, Atsushi

The Recently, electronics and IT technologies have been rapidly innovated and have been introduced to power system protection & control system to achieve high reliability, maintainability and more functionality. Concerning the distribution substation application, digital relays have been applied for more than 10 years. Because of a number of electronic devices used for it, product cost becomes higher. Also, products installed during the past high-growth period will be at the end of lifetime and will be replaced. Therefore, replacing market is expected to grow and the reduction of cost is demanded. Considering above mentioned background, second generation digital protection and control unit as a successor is designed to have following concepts. Functional integration based on advanced digital technologies, Ethernet LAN based indoor communication network, cost reduction and downsizing. Pondering above concepts, integration of protection and control function is adopted in contrary to the functional segregation applied to the previous system in order to achieve one-unit concept. Also the adoption of Ethernet LAN for inter-unit communication is objective. This report shows the development of second-generation digital relay for distribution substation, which is equipped with control function and Ethernet LAN by reducing the size of auxiliary transformer unit and the same size as previous product is realized.

Digital technologies in occupational therapy and physiotherapy undergraduate and postgraduate education: a scoping review protocol.

PubMed

Olivier, Benita; Verdonck, Michele; Casteleijn, Daleen

2017-11-01

How have digital technologies been used in occupational therapy and physiotherapy undergraduate and postgraduate education?Specifically, the objective of this scoping review is to present an overview of research on the use of digital technologies in terms of type of digital technology used, pedagogy associated with the use of digital technology, subject/topic/area of application, experiences/perception of digital technology used, outcomes of the digital technology used and challenges to the use of digital technologies in occupational therapy and physiotherapy undergraduate and postgraduate education.

Systems study for an Integrated Digital-Electric Aircraft (IDEA)

NASA Technical Reports Server (NTRS)

Tagge, G. E.; Irish, L. A.; Bailey, A. R.

1985-01-01

The results of the Integrated Digital/Electric Aircraft (IDEA) Study are presented. Airplanes with advanced systems were, defined and evaluated, as a means of identifying potential high payoff research tasks. A baseline airplane was defined for comparison, typical of a 1990's airplane with advanced active controls, propulsion, aerodynamics, and structures technology. Trade studies led to definition of an IDEA airplane, with extensive digital systems and electric secondary power distribution. This airplane showed an improvement of 3% in fuel use and 1.8% in DOC relative to the baseline configuration. An alternate configuration, an advanced technology turboprop, was also evaluated, with greater improvement supported by digital electric systems. Recommended research programs were defined for high risk, high payoff areas appropriate for implementation under NASA leadership.

A simplified close range photogrammetric technique for soil erosion assessment

USDA-ARS?s Scientific Manuscript database

Surface reconstruction using digital photogrammetry offers a great advantage for soil erosion research. The technology can be cumbersome for field application as it relies on the accurate measurement of control points often using a survey grade instruments. Also, even though digital photogrammetry h...

An application of LANDSAT digital technology to forest fire fuel type mapping

NASA Technical Reports Server (NTRS)

Kourtz, P. H.

1977-01-01

The role of digital classifications suitable as fuel maps was examined. A Taylor enhancement was produced for an 8 million hectare fire control region showing water, muskeg, coniferous, deciduous and mixed stands, clearcut logging, burned areas, regeneration areas, nonforested areas and large forest roads. Use of the map by fire control personnel demonstrated its usefulness for initial attack decision making.

Digital Citizenship Policy Development Guide

ERIC Educational Resources Information Center

Alberta Education, 2012

2012-01-01

Education leaders are re-examining acceptable use policies in light of the increasing use of highly mobile information technologies. While acceptable use policies were developed to manage and control behaviour, a digital citizenship policy takes a more comprehensive approach by recognizing the important role of education in preparing digital…

Automated site characterization for robotic sample acquisition systems

NASA Astrophysics Data System (ADS)

Scholl, Marija S.; Eberlein, Susan J.

1993-04-01

A mobile, semiautonomous vehicle with multiple sensors and on-board intelligence is proposed for performing preliminary scientific investigations on extraterrestrial bodies prior to human exploration. Two technologies, a hybrid optical-digital computer system based on optical correlator technology and an image and instrument data analysis system, provide complementary capabilities that might be part of an instrument package for an intelligent robotic vehicle. The hybrid digital-optical vision system could perform real-time image classification tasks using an optical correlator with programmable matched filters under control of a digital microcomputer. The data analysis system would analyze visible and multiband imagery to extract mineral composition and textural information for geologic characterization. Together these technologies would support the site characterization needs of a robotic vehicle for both navigational and scientific purposes.

Digital Control Technologies for Modular DC-DC Converters

NASA Technical Reports Server (NTRS)

Button, Robert M.; Kascak, Peter E.; Lebron-Velilla, Ramon

2002-01-01

Recent trends in aerospace Power Management and Distribution (PMAD) systems focus on using commercial off-the-shelf (COTS) components as standard building blocks. This move to more modular designs has been driven by a desire to reduce costs and development times, but is also due to the impressive power density and efficiency numbers achieved by today's commercial DC-DC converters. However, the PMAD designer quickly learns of the hidden "costs" of using COTS converters. The most significant cost is the required addition of external input filters to meet strict electromagnetic interference (MIAMI) requirements for space systems. In fact, the high power density numbers achieved by the commercial manufacturers are greatly due to the lack of necessary input filters included in the COTS module. The NASA Glenn Research Center is currently pursuing a digital control technology that addresses this problem with modular DC-DC converters. This paper presents the digital control technologies that have been developed to greatly reduce the input filter requirements for paralleled, modular DC-DC converters. Initial test result show that the input filter's inductor size was reduced by 75 percent, and the capacitor size was reduced by 94 percent while maintaining the same power quality specifications.

Application of FDM three-dimensional printing technology in the digital manufacture of custom edentulous mandible trays

PubMed Central

Chen, Hu; Yang, Xu; Chen, Litong; Wang, Yong; Sun, Yuchun

2016-01-01

The objective was to establish and evaluate a method for manufacture of custom trays for edentulous jaws using computer aided design and fused deposition modeling (FDM) technologies. A digital method for design the custom trays for edentulous jaws was established. The tissue surface data of ten standard mandibular edentulous plaster models, which was used to design the digital custom tray in a reverse engineering software, were obtained using a 3D scanner. The designed tray was printed by a 3D FDM printing device. Another ten hand-made custom trays were produced as control. The 3-dimentional surface data of models and custom trays was scanned to evaluate the accuracy of reserved impression space, while the difference between digitally made trays and hand-made trays were analyzed. The digitally made custom trays achieved a good matching with the mandibular model, showing higher accuracy than the hand-made ones. There was no significant difference of the reserved space between different models and its matched digitally made trays. With 3D scanning, CAD and FDM technology, an efficient method of custom tray production was established, which achieved a high reproducibility and accuracy. PMID:26763620

A Research Framework for Demonstrating Benefits of Advanced Control Room Technologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Blanc, Katya; Boring, Ronald; Joe, Jeffrey

Control Room modernization is an important part of life extension for the existing light water reactor fleet. None of the 99 currently operating commercial nuclear power plants in the U.S. has completed a full-scale control room modernization to date. A full-scale modernization might, for example, entail replacement of all analog panels with digital workstations. Such modernizations have been undertaken successfully in upgrades in Europe and Asia, but the U.S. has yet to undertake a control room upgrade of this magnitude. Instead, nuclear power plant main control rooms for the existing commercial reactor fleet remain significantly analog, with only limited digitalmore » modernizations. Previous research under the U.S. Department of Energy’s Light Water Reactor Sustainability Program has helped establish a systematic process for control room upgrades that support the transition to a hybrid control. While the guidance developed to date helps streamline the process of modernization and reduce costs and uncertainty associated with introducing digital control technologies into an existing control room, these upgrades do not achieve the full potential of newer technologies that might otherwise enhance plant and operator performance. The aim of the control room benefits research presented here is to identify previously overlooked benefits of modernization, identify candidate technologies that may facilitate such benefits, and demonstrate these technologies through human factors research. This report serves as an outline for planned research on the benefits of greater modernization in the main control rooms of nuclear power plants.« less

Design and implementation of Remote Digital Energy Meter (RDEM) based on GSM technology

NASA Astrophysics Data System (ADS)

Khan, Muhammad Waseem; Wang, Jie; Irfan, Muhammad; Shiraz, M.; Khan, Ali Hassan

2017-11-01

Electric power is one of the basic requirement for socio economic and social prosperity of any country, which is mainly employs for domestic, industrial and agricultural sectors. The primary purpose of this research is to design and implement an energy meter which can remotely control and monitor through global system for mobile (GSM) communication technology. For this purpose, a single phase or three phase digital energy meters are used to add on different advanced modules. The energy meter can be activated and display power consumption information at the consumer premises on liquid crystal display and through a short message service (SMS) by using GSM technology. At the power sending end, an energy meter can be remotely control and monitor through GSM technology without any system disturbances. This study will lead to make the system easier, economical, reliable and efficient for the electrical department.

MDIS Compatibility: Computer Assisted Quality Control and Telemammography (Breast Cancer)

DTIC Science & Technology

1994-01-20

Radiography Workshop: Quality Assurance and Radiation Protection. May 7-9, Mannheim. Schnetztor - Verlag; 1992: 90-91. 2. Panizza P., Del Maschio A- Digital...3. Panizza P., Cattaneo M., Rodighiero M.G., et al. Course on Digital Radiology and PACS Technology - Clinical Application: Breast (L’Aquila) Scuola

Older Adults and Emerging Digital Service Delivery: A Mixed Methods Study on Information and Communications Technology Use, Skills, and Attitudes.

PubMed

Siren, Anu; Knudsen, Sine Grønborg

2017-01-01

Based on data from a survey (n = 3291) and 14 qualitative interviews among Danish older adults, this study investigated the use of, and attitudes toward, information communications technology (ICT) and the digital delivery of public services. While age, gender, and socioeconomic status were associated with use of ICT, these determinants lost their explanatory power when we controlled for attitudes and experiences. We identified three segments that differed in their use of ICT and attitudes toward digital service delivery. As nonuse of ICT often results from the lack of willingness to use it rather than from material or cognitive deficiencies, policy measures for bridging the digital divide should focus on skills and confidence rather than on access or ability.

Achieving Helicopter Modernization with Advanced Technology Turbine Engines

DTIC Science & Technology

1999-04-01

computer modeling of compressor and turbine aerody- digital engine control ( FADEC ) with manual backup. namics. Modern directionally solidified and single...controlled by a dual RAH.66A M channel FADEC , and features a very simple installation "" Improved Gross Weight and significantly reduced pilot...air separation efficiencies as an "advanced technology" engine. Technological meas- high as 97.5%. The FADEC improves acceleration, ures include but

Benefits of Advanced Control Room Technologies: Phase One Upgrades to the HSSL, Research Plan, and Performance Measures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Le Blanc, Katya; Joe, Jeffrey; Rice, Brandon

Control Room modernization is an important part of life extension for the existing light water reactor fleet. None of the 99 currently operating commercial nuclear power plants in the U.S. has completed a full-scale control room modernization to date. A full-scale modernization might, for example, entail replacement of all analog panels with digital workstations. Such modernizations have been undertaken successfully in upgrades in Europe and Asia, but the U.S. has yet to undertake a control room upgrade of this magnitude. Instead, nuclear power plant main control rooms for the existing commercial reactor fleet remain significantly analog, with only limited digitalmore » modernizations. Previous research under the U.S. Department of Energy’s Light Water Reactor Sustainability Program has helped establish a systematic process for control room upgrades that support the transition to a hybrid control room. While the guidance developed to date helps streamline the process of modernization and reduce costs and uncertainty associated with introducing digital control technologies into an existing control room, these upgrades do not achieve the full potential of newer technologies that might otherwise enhance plant and operator performance. The aim of the control room benefits research is to identify previously overlooked benefits of modernization, identify candidate technologies that may facilitate such benefits, and demonstrate these technologies through human factors research. This report describes the initial upgrades to the HSSL and outlines the methodology for a pilot test of the HSSL configuration.« less

Reinventing Schools: The Technology Is Now!

ERIC Educational Resources Information Center

Ellmore, Douglas A., Sr.; Olson, Steve E.; Smith, Phillip M.

1995-01-01

Today's children have grown up immersed in a world of computers and other information technologies. They play video games; they listen to music on digital compact disks; they help their families program the computerized controls of videocassette players. With all of the exciting innovations in computer technology, children have the opportunity to…

A REVIEW OF HUMAN-SYSTEM INTERFACE DESIGN ISSUES OBSERVED DURING ANALOG-TO-DIGITAL AND DIGITAL-TO-DIGITAL MIGRATIONS IN U.S. NUCLEAR POWER PLANTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kovesdi, C.; Joe, J.

The United States (U.S.) Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) program is developing a scientific basis through targeted research and development (R&D) to support the U.S. nuclear power plant (NPP) fleet in extending their existing licensing period and ensuring their long-term reliability, productivity, safety, and security. Over the last several years, human factors engineering (HFE) professionals at the Idaho National Laboratory (INL) have supported the LWRS Advanced Instrumentation, Information, and Control (II&C) System Technologies pathway across several U.S. commercial NPPs in analog-to-digital migrations (i.e., turbine control systems) and digital-to-digital migrations (i.e., Safety Parameter Display System). These effortsmore » have included in-depth human factors evaluation of proposed human-system interface (HSI) design concepts against established U.S. Nuclear Regulatory Commission (NRC) design guidelines from NUREG-0700, Rev 2 to inform subsequent HSI design prior to transitioning into Verification and Validation. This paper discusses some of the overarching design issues observed from these past HFE evaluations. In addition, this work presents some observed challenges such as common tradeoffs utilities are likely to face when introducing new HSI technologies into NPP hybrid control rooms. The primary purpose of this work is to distill these observed design issues into general HSI design guidance that industry can use in early stages of HSI design.« less

A Network Scheduling Model for Distributed Control Simulation

NASA Technical Reports Server (NTRS)

Culley, Dennis; Thomas, George; Aretskin-Hariton, Eliot

2016-01-01

Distributed engine control is a hardware technology that radically alters the architecture for aircraft engine control systems. Of its own accord, it does not change the function of control, rather it seeks to address the implementation issues for weight-constrained vehicles that can limit overall system performance and increase life-cycle cost. However, an inherent feature of this technology, digital communication networks, alters the flow of information between critical elements of the closed-loop control. Whereas control information has been available continuously in conventional centralized control architectures through virtue of analog signaling, moving forward, it will be transmitted digitally in serial fashion over the network(s) in distributed control architectures. An underlying effect is that all of the control information arrives asynchronously and may not be available every loop interval of the controller, therefore it must be scheduled. This paper proposes a methodology for modeling the nominal data flow over these networks and examines the resulting impact for an aero turbine engine system simulation.

Evolutions in food marketing, quantifying the impact, and policy implications.

PubMed

Cairns, Georgina

2013-03-01

A case study on interactive digital marketing examined the adequacy of extant policy controls and their underpinning paradigms to constrain the effects of this rapidly emerging practice. Findings were interactive digital marketing is expanding the strategies available to promote products, brands and consumer behaviours. It facilitates relational marketing; the collection of personal data for marketing; integration of the marketing mix, and provides a platform for consumers to engage in the co-creation of marketing communications. The paradigmatic logic of current policies to constrain youth-oriented food marketing does not address the interactive nature of digital marketing. The evidence base on the effects of HFSS marketing and policy interventions is based on conceptualizations of marketing as a force promoting transactions rather than interactions. Digital technologies are generating rich consumer data. Interactive digital technologies increase the complexity of the task of quantifying the impact of marketing. The rapidity of its uptake also increases urgency of need to identify appropriate effects measures. Independent analysis of commercial consumer data (appropriately transformed to protect commercial confidentiality and personal privacy) would provide evidence sources for policy on the impacts of commercial food and beverage marketing and policy controls. Copyright © 2012 Elsevier Ltd. All rights reserved.

Visualizing the Diffusion of Digital Mammography in New York State.

PubMed

Boscoe, Francis P; Zhang, Xiuling

2017-04-01

Background: Digital mammography saw rapid adoption during the first decade of the 2000s. We were interested in identifying the times and locations where the technology was introduced within the state of New York as a way of illustrating the uneven introduction of this technology. Methods: Using a sample of Medicare claims data from the period 2004 to 2012 from women ages 65 and over without cancer, we calculated the percentage of mammograms that were digital by zip code of residence and illustrated them with a series of smoothed maps. Results: Maps for three of the years (2005, 2008, and 2011) show the conversion from almost no digital mammography to nearly all digital mammography. The 2008 map reveals sharp disparities between areas that had and had not yet adopted the technology. Socioeconomic differences explain some of this pattern. Conclusions: Geographic disparities in access to medical technology are underappreciated relative to other sources of disparities. Our method provides a way of measuring and communicating this phenomenon. Impact: Our method could be applied to illuminate current examples, where access to medical technology is highly uneven, such as 3D tomography and robotic surgery. Cancer Epidemiol Biomarkers Prev; 26(4); 490-4. ©2017 AACR See all the articles in this CEBP Focus section, "Geospatial Approaches to Cancer Control and Population Sciences." ©2017 American Association for Cancer Research.

Indoor Navigation by People with Visual Impairment Using a Digital Sign System

PubMed Central

Legge, Gordon E.; Beckmann, Paul J.; Tjan, Bosco S.; Havey, Gary; Kramer, Kevin; Rolkosky, David; Gage, Rachel; Chen, Muzi; Puchakayala, Sravan; Rangarajan, Aravindhan

2013-01-01

There is a need for adaptive technology to enhance indoor wayfinding by visually-impaired people. To address this need, we have developed and tested a Digital Sign System. The hardware and software consist of digitally-encoded signs widely distributed throughout a building, a handheld sign-reader based on an infrared camera, image-processing software, and a talking digital map running on a mobile device. Four groups of subjects—blind, low vision, blindfolded sighted, and normally sighted controls—were evaluated on three navigation tasks. The results demonstrate that the technology can be used reliably in retrieving information from the signs during active mobility, in finding nearby points of interest, and following routes in a building from a starting location to a destination. The visually impaired subjects accurately and independently completed the navigation tasks, but took substantially longer than normally sighted controls. This fully functional prototype system demonstrates the feasibility of technology enabling independent indoor navigation by people with visual impairment. PMID:24116156

Advanced Electronic Technology

DTIC Science & Technology

1977-11-15

Electronics 15 III. Materials Research 15 TV. Microelectronics 16 V. Surface- Wave Technology 16 DATA SYSTEMS DIVISION 2 INTRODUCTION This...Processing Digital Voice Processing Packet Speech Wideband Integrated Voice/Data Technology Radar Signal Processing Technology Nuclear Safety Designs...facilities make it possible to track the status of these jobs, retrieve their job control language listings, and direct a copy of printed or punched

An overview of integrated flight-propulsion controls flight research on the NASA F-15 research airplane

NASA Technical Reports Server (NTRS)

Burcham, Frank W., Jr.; Gatlin, Donald H.; Stewart, James F.

1995-01-01

The NASA Dryden Flight Research Center has been conducting integrated flight-propulsion control flight research using the NASA F-15 airplane for the past 12 years. The research began with the digital electronic engine control (DEEC) project, followed by the F100 Engine Model Derivative (EMD). HIDEC (Highly Integrated Digital Electronic Control) became the umbrella name for a series of experiments including: the Advanced Digital Engine Controls System (ADECS), a twin jet acoustics flight experiment, self-repairing flight control system (SRFCS), performance-seeking control (PSC), and propulsion controlled aircraft (PCA). The upcoming F-15 project is ACTIVE (Advanced Control Technology for Integrated Vehicles). This paper provides a brief summary of these activities and provides background for the PCA and PSC papers, and includes a bibliography of all papers and reports from the NASA F-15 project.

Survey of student attitudes towards digital simulation technologies at a dental school in China.

PubMed

Ren, Q; Wang, Y; Zheng, Q; Ye, L; Zhou, X D; Zhang, L L

2017-08-01

Digital simulation technologies have become widespread in healthcare education, especially in dentistry; these technologies include digital X-ray images, digital microscopes, virtual pathology slides and other types of simulation. This study aimed to assess students' attitudes towards digital simulation technologies at a large, top-ranked dental school in China, as well as find out how students compare the digital technologies with traditional training methods. In April 2015, a custom-designed questionnaire was distributed to a total of 389 students who had received digital technology and simulation-based training in West China Dental School during 2012-2014. Results of a cross-sectional survey show that most students accept digital simulation technology; they report that the technology is stimulating and facilitates self-directed and self-paced learning. These findings, together with the objective advantages of digital technology, suggest that digital simulation training offers significant potential for dental education, highlighting the need for further research and more widespread implementation. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Care relationships at stake? Home healthcare professionals' experiences with digital medicine dispensers - a qualitative study.

PubMed

Nakrem, Sigrid; Solbjør, Marit; Pettersen, Ida Nilstad; Kleiven, Hanne Hestvik

2018-01-15

Although digital technologies can mitigate the burdens of home healthcare services caused by an ageing population that lives at home longer with complex health problems, research on the impacts and consequences of digitalised remote communication between patients and caregivers is lacking. The present study explores how home healthcare professionals had experienced the introduction of digital medicine dispensers and their influence on patient-caregiver relationships. The multi-case study comprised semi-structured interviews with 21 healthcare professionals whose home healthcare service involved using the digital medicine dispensers. The constant comparative method was used for data analyses. Altogether, interviewed healthcare professionals reported three main technology-related impacts upon their patient-caregiver relationships. First, national and local pressure to increase efficiency had troubled their relationships with patients who suspected that municipalities have sought to lower costs by reducing and digitalising services. Participants reported having to consider such worries when introducing technologies into their services. Second, participants reported a shift towards empowering patients. Digital technology can empower patients who value their independence, whereas safety is more important for other patients. Healthcare professionals needed to ensure that replacing care tasks with technology implies safe and improved care. Third, the safety and quality of digital healthcare services continues to depend upon surveillance and control mechanisms that compensate for less face-to-face monitoring. Participants did not consider the possibility that surveillance exposes information about patients' everyday lives to be problematic, but to constitute opportunities for adjusting services to meet patients' needs. Technologies such as digital medicine dispensers can improve the efficiency of healthcare services and enhance patients' independence when introduced in a way that empowers patients as well as safeguards trust and service quality. Conversely, the patient-caregiver relationship can suffer if the technology does not meet patients' needs and fails to offer safe and trustworthy services. Upon introducing technology, home healthcare professionals therefore need to carefully consider the benefits and possible disadvantages of the technology. Ethical implications for both individuals and societies need to be further discussed.

Design and performance of a custom ASIC digitizer for wire chamber readout in 65 nm CMOS technology

NASA Astrophysics Data System (ADS)

Lee, M. J.; Brown, D. N.; Chang, J. K.; Ding, D.; Gnani, D.; Grace, C. R.; Jones, J. A.; Kolomensky, Y. G.; von der Lippe, H.; Mcvittie, P. J.; Stettler, M. W.; Walder, J.-P.

2015-06-01

We present the design and performance of a prototype ASIC digitizer for integrated wire chamber readout, implemented in 65 nm commercial CMOS technology. Each channel of the 4-channel prototype is composed of two 16-bit Time-to-Digital Converters (TDCs), one 8-bit Analog-to-Digital Converter (ADC), a front-end preamplifier and shaper, plus digital and analog buffers that support a variety of digitization chains. The prototype has a multiplexed digital backend that executes a state machine, distributes control and timing signals, and buffers data for serial output. Laboratory bench tests measure the absolute TDC resolution between 74 ps and 480 ps, growing with the absolute delay, and a relative time resolution of 19 ps. Resolution outliers due to cross-talk between clock signals and supply or reference voltages are seen. After calibration, the ADC displays good linearity and noise performance, with an effective number of bits of 6.9. Under normal operating conditions the circuit consumes 32 mW per channel. Potential design improvements to address the resolution drift and tails are discussed.

Real-time optical fiber digital speckle pattern interferometry for industrial applications

NASA Astrophysics Data System (ADS)

Chan, Robert K.; Cheung, Y. M.; Lo, C. H.; Tam, T. K.

1997-03-01

There is current interest, especially in the industrial sector, to use the digital speckle pattern interferometry (DSPI) technique to measure surface stress. Indeed, many publications in the subject are evident of the growing interests in the field. However, to bring the technology to industrial use requires the integration of several emerging technologies, viz. optics, feedback control, electronics, imaging processing and digital signal processing. Due to the highly interdisciplinary nature of the technique, successful implementation and development require expertise in all of the fields. At Baptist University, under the funding of a major industrial grant, we are developing the technology for the industrial sector. Our system fully exploits optical fibers and diode lasers in the design to enable practical and rugged systems suited for industrial applications. Besides the development in optics, we have broken away from the reliance of a microcomputer PC platform for both image capture and processing, and have developed a digital signal processing array system that can handle simultaneous and independent image capture/processing with feedback control. The system, named CASPA for 'cascadable architecture signal processing array,' is a third generation development system that utilizes up to 7 digital signal processors has proved to be a very powerful system. With our CASPA we are now in a better position to developing novel optical measurement systems for industrial application that may require different measurement systems to operate concurrently and requiring information exchange between the systems. Applications in mind such as simultaneous in-plane and out-of-plane DSPI image capture/process, vibrational analysis with interactive DSPI and phase shifting control of optical systems are a few good examples of the potentials.

Digital Architecture – Results From a Gap Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oxstrand, Johanna Helene; Thomas, Kenneth David; Fitzgerald, Kirk

The digital architecture is defined as a collection of IT capabilities needed to support and integrate a wide-spectrum of real-time digital capabilities for nuclear power plant performance improvements. The digital architecture can be thought of as an integration of the separate I&C and information systems already in place in NPPs, brought together for the purpose of creating new levels of automation in NPP work activities. In some cases, it might be an extension of the current communication systems, to provide digital communications where they are currently analog only. This collection of IT capabilities must in turn be based on amore » set of user requirements that must be supported for the interconnected technologies to operate in an integrated manner. These requirements, simply put, are a statement of what sorts of digital work functions will be exercised in a fully-implemented seamless digital environment and how much they will be used. The goal of the digital architecture research is to develop a methodology for mapping nuclear power plant operational and support activities into the digital architecture, which includes the development of a consensus model for advanced information and control architecture. The consensus model should be developed at a level of detail that is useful to the industry. In other words, not so detailed that it specifies specific protocols and not so vague that it is only provides a high level description of technology. The next step towards the model development is to determine the current state of digital architecture at typical NPPs. To investigate the current state, the researchers conducted a gap analysis to determine to what extent the NPPs can support the future digital technology environment with their existing I&C and IT structure, and where gaps exist with respect to the full deployment of technology over time. The methodology, result, and conclusions from the gap analysis are described in this report.« less

Digital switched hydraulics

NASA Astrophysics Data System (ADS)

Pan, Min; Plummer, Andrew

2018-06-01

This paper reviews recent developments in digital switched hydraulics particularly the switched inertance hydraulic systems (SIHSs). The performance of SIHSs is presented in brief with a discussion of several possible configurations and control strategies. The soft switching technology and high-speed switching valve design techniques are discussed. Challenges and recommendations are given based on the current research achievements.

Advanced power system protection and incipient fault detection and protection of spaceborne power systems

NASA Technical Reports Server (NTRS)

Russell, B. Don

1989-01-01

This research concentrated on the application of advanced signal processing, expert system, and digital technologies for the detection and control of low grade, incipient faults on spaceborne power systems. The researchers have considerable experience in the application of advanced digital technologies and the protection of terrestrial power systems. This experience was used in the current contracts to develop new approaches for protecting the electrical distribution system in spaceborne applications. The project was divided into three distinct areas: (1) investigate the applicability of fault detection algorithms developed for terrestrial power systems to the detection of faults in spaceborne systems; (2) investigate the digital hardware and architectures required to monitor and control spaceborne power systems with full capability to implement new detection and diagnostic algorithms; and (3) develop a real-time expert operating system for implementing diagnostic and protection algorithms. Significant progress has been made in each of the above areas. Several terrestrial fault detection algorithms were modified to better adapt to spaceborne power system environments. Several digital architectures were developed and evaluated in light of the fault detection algorithms.

A fuzzy control design case: The fuzzy PLL

NASA Technical Reports Server (NTRS)

Teodorescu, H. N.; Bogdan, I.

1992-01-01

The aim of this paper is to present a typical fuzzy control design case. The analyzed controlled systems are the phase-locked loops (PLL's)--classic systems realized in both analogic and digital technology. The crisp PLL devices are well known.

Energy Efficient Engine: Control system preliminary definition report

NASA Technical Reports Server (NTRS)

Howe, David C.

1986-01-01

The object of the Control Preliminary Definition Program was to define a preliminary control system concept as a part of the Energy Efficient Engine program. The program was limited to a conceptual definition of a full authority digital electronic control system. System requirements were determined and a control system was conceptually defined to these requirements. Areas requiring technological development were identified and a plan was established for implementing the identified technological features, including a control technology demonstration. A significant element of this program was a study of the potential benefits of closed-loop active clearance control, along with laboratory tests of candidate clearance sensor elements for a closed loop system.

The Virtual Hospital: experiences in creating and sustaining a digital library.

PubMed Central

D'Alessandro, M P; Galvin, J R; Erkonen, W E; Choi, T A; Lacey, D L; Colbert, S I

1998-01-01

A university and its faculty encompass a wealth of content, which is often freely supplied to commercial publishers who profit from it. Emerging digital library technology holds promise for allowing the creation of digital libraries and digital presses that can allow faculty and universities to bypass commercial publishers, retain control of their content, and distribute it directly to users, allowing the university and faculty to better serve their constituencies. The purpose of this paper is to show how this can be done. A methodology for overcoming the technical, social, political, and economic barriers involved in creating, distributing and organizing a digital library was developed, implemented, and refined over seven years. Over the seven years, 120 textbooks and booklets were placed in the Virtual Hospital digital library, from 159 authors in twenty-nine departments and four colleges at The University of Iowa. The digital library received extensive use by individuals around the world. A new paradigm for academic publishing was created, involving a university and faculty owned peer reviewed digital press implemented using digital library technology. The concept has been embraced by The University of Iowa, and it has pledged to sustain the digital press in order to allow. The University of Iowa to fulfill its mission of creating, organizing, and disseminating information better. PMID:9803300

User`s manual for the CDC-1 digitizer controller

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferron, J.R.

1994-09-01

A detailed description of how to use the CDC-1 digitizer controller is given. The CDC-1 is used with the CAMAC format digitizer models in the TRAQ series (manufactured by DSP Technology Inc.), the DAD-1 data acquisition daughter board, and the Intel i860-based SuperCard-2 (manufactured, by CSP Inc.) to form a high speed data acquisition and real time analysis system. Data can be transferred to the memory on the SuperCard-2 at a rate as high as 40 million 14-bit samples per second. Depending on the model of TRAQ digitizer in use, digitizing rates up to 3.33 MHz are supported (with eightmore » data channels), or, for instance, at a sample rate of 100 kHz, 384 data channels can be acquired.« less

Dual-spin attitude control for outer planet missions

NASA Technical Reports Server (NTRS)

Ward, R. S.; Tauke, G. J.

1977-01-01

The applicability of dual-spin technology to a Jupiter orbiter with probe mission was investigated. Basic mission and system level attitude control requirements were established and preliminary mechanization and control concepts developed. A comprehensive 18-degree-of-freedom digital simulation was utilized extensively to establish control laws, study dynamic interactions, and determined key sensitivities. Fundamental system/subsystem constraints were identified, and the applicability of dual-spin technology to a Jupiter orbiter with probe mission was validated.

Digital Downsides: Exploring University Students' Negative Engagements with Digital Technology

ERIC Educational Resources Information Center

Selwyn, Neil

2016-01-01

Digital technologies are now an integral feature of university study. As such, academic research has tended to concentrate on the potential of digital technologies to support, extend and even "enhance" student learning. This paper, in contrast, explores the rather more messy realities of students' engagements with digital technology. In…

Some Aspects in Photogrammetry Education at the Department of Geodesy and Cadastre of the VGTU

NASA Astrophysics Data System (ADS)

Ruzgienė, Birutė

2008-03-01

The education in photogrammetry is very important when applying photogrammetric methods for the terrain mapping purposes, for spatial data modelling, solving engineering tasks, measuring of architectural monuments etc. During the time the traditional photogrammetric technologies have been changing to modern fully digital photogrammetric workflow. The number of potential users of the photogrammetric methods tends to increase, because of high-degree automation in photographs (images) processing. The main subjects in Photogrammetry (particularly in Digital Photogrammetry) educational process are discussed. Different methods and digital systems are demonstrated with the examples of aerial photogrammetry products. The main objective is to search the possibilities for training in the photogrammetric measurements. Special attention is paid to the stereo plotting from aerial photography applying modified for teaching analytical technology. The integration of functionality of Digital Photogrammetric Systems and Digital Image Processing is analysed as well with an intention of extending the application areas and possibilities for usage of modern technologies in urban mapping and land cadastre. The practical presentation of photos geometry restitution is implemented as significant part of the studies. The interactive teaching for main photogrammetric procedures and controlling systems are highly desirable that without any doubt improve the quality of educational process.

Adapting Digital Libraries to Continual Evolution

NASA Technical Reports Server (NTRS)

Barkstrom, Bruce R.; Finch, Melinda; Ferebee, Michelle; Mackey, Calvin

2002-01-01

In this paper, we describe five investment streams (data storage infrastructure, knowledge management, data production control, data transport and security, and personnel skill mix) that need to be balanced against short-term operating demands in order to maximize the probability of long-term viability of a digital library. Because of the rapid pace of information technology change, a digital library cannot be a static institution. Rather, it has to become a flexible organization adapted to continuous evolution of its infrastructure.

Flight control systems development and flight test experience with the HiMAT research vehicles

NASA Technical Reports Server (NTRS)

Kempel, Robert W.; Earls, Michael R.

1988-01-01

Two highly maneuverable aircraft technology (HiMAT) remotely piloted vehicles were flown a total of 26 flights. These subscale vehicles were of advanced aerodynamic configuration with advanced technology concepts such as composite and metallic structures, digital integrated propulsion control, and ground (primary) and airborne (backup) relaxed static stability, digital fly-by-wire control systems. Extensive systems development, checkout, and flight qualification were required to conduct the flight test program. The design maneuver goal was to achieve a sustained 8-g turn at Mach 0.9 at an altitude of 25,000 feet. This goal was achieved, along with the acquisition of high-quality flight data at subsonic and supersonic Mach numbers. Control systems were modified in a variety of ways using the flight-determined aerodynamic characteristics. The HiMAT program was successfully completed with approximately 11 hours of total flight time.

"There's Not Enough Knowledge Out There": Examining Older Adults' Perceptions of Digital Technology Use and Digital Inclusion Classes.

PubMed

Betts, Lucy R; Hill, Rowena; Gardner, Sarah E

2017-10-01

Older adults' definitions of digital technology, and experiences of digital inclusion sessions, were examined using qualitative approaches. Seventeen older adults (aged between 54 and 85 years) participated in two focus groups that each lasted approximately 90 min to explore how older adults understood technology within their lived experience. Interpretative phenomenological analysis yielded two main themes: thirst for knowledge and a wish list for digital technology sessions. A separate content analysis was performed to identify what technology older adults identified as digital technology. This analysis revealed that the older adults most frequently defined digital technology as computers and telephones. The findings support the conclusions that this group of older adults, some of whom were "successful users," have a wide knowledge of digital technology, are interested in gaining more skills, and desire knowledge acquisition through personalized one-to-one learning sessions.

[Understanding chair-side digital technology for stomatology from an engineering viewpoint].

PubMed

Zhao, Y J; Wang, Y

2018-04-09

In recent years with the rapid development of digital technology for stomatology, the application field, application model, technical features and technical connotation of the chair-side digital technology has got development and change. The open modular system has gradually replaced the traditional closed system, and the application field of digital technology is no longer limited to chair-side dental restoration, it also has been extend to various kinds of chair-side digital treatment-assisted technology. In this paper, from the engineering point of view, the up to date general connotation of chair-side digital technology was explained, the characteristics and the development of each unit in chair-side digital technology were analyzed, and the application pattern and the localization status were also discussed in this paper. The aim of this paper was to introduce the trend of chair-side digital technological to readers and to better guide clinical application.

Environment and health: Probes and sensors for environment digital control

NASA Astrophysics Data System (ADS)

Schettini, Chiara

2014-05-01

The idea of studying the environment using New Technologies (NT) came from a MIUR (Ministry of Education of the Italian Government) notice that allocated funds for the realization of innovative school science projects. The "Environment and Health" project uses probes and sensors for digital control of environment (water, air and soil). The working group was composed of 4 Science teachers from 'Liceo Statale G. Mazzini ', under the coordination of teacher Chiara Schettini. The Didactic Section of Naples City of Sciences helped the teachers in developing the project and it organized a refresher course for them on the utilization of digital control sensors. The project connects Environment and Technology because the study of the natural aspects and the analysis of the chemical-physical parameters give students and teachers skills for studying the environment based on the utilization of NT in computing data elaboration. During the practical project, samples of air, water and soil are gathered in different contexts. Sample analysis was done in the school's scientific laboratory with digitally controlled sensors. The data are elaborated with specific software and the results have been written in a booklet and in a computing database. During the first year, the project involved 6 school classes (age of the students 14—15 years), under the coordination of Science teachers. The project aims are: 1) making students more aware about environmental matters 2) achieving basic skills for evaluating air, water and soil quality. 3) achieving strong skills for the utilization of digitally controlled sensors. 4) achieving computing skills for elaborating and presenting data. The project aims to develop a large environmental conscience and the need of a ' good ' environment for defending our health. Moreover it would increase the importance of NT as an instrument of knowledge.

Building a Digital Consciousness: Make "Public and Permanent" the Golden Rule

ERIC Educational Resources Information Center

Guerry, Richard

2012-01-01

Most discussions about keeping kids safe online center around two issues: (1) With the rapid development and dissemination of digital technology, how can we stay ahead of what our students are doing?; and (2) What controls are available to prevent students from visiting inappropriate sites? These are reasonable questions, but they ignore two…

Human-Technology Relationality and Self-Network Organization: Players and Avatars in World of Warcraft

ERIC Educational Resources Information Center

Banks, Jaime

2013-01-01

Massively multiplayer online roleplaying games, or MMOs, present an increasingly popular digital media experience whereby identity emerges as players contribute materially to play but contributions are governed by affordances and constraints of the game. Unique to this medium is the player's ability to create and control a digital body--an…

Primary school teachers' use of digital technology in mathematics: the complexities

NASA Astrophysics Data System (ADS)

Loong, Esther Yook-Kin; Herbert, Sandra

2018-02-01

This paper seeks to theorise primary teachers' degree of integration of digital technology in the mathematics classroom. In an age where digital technology use is ubiquitous, the issues surrounding teachers' choice, and ultimately their uptake of digital technologies in the classroom, is an area that need to be further unpacked. Cross-case analysis of the two teachers' uptake of digital technologies in their classroom, their pedagogical approaches and the reason for their choices provide insight into teachers' technological, pedagogical and content knowledge (TPACK). Differences in the way the teachers use digital technology in their classroom seem to be connected to their TPACK developmental stage.

WTEC panel report on European nuclear instrumentation and controls

NASA Technical Reports Server (NTRS)

White, James D.; Lanning, David D.; Beltracchi, Leo; Best, Fred R.; Easter, James R.; Oakes, Lester C.; Sudduth, A. L.

1991-01-01

Control and instrumentation systems might be called the 'brain' and 'senses' of a nuclear power plant. As such they become the key elements in the integrated operation of these plants. Recent developments in digital equipment have allowed a dramatic change in the design of these instrument and control (I&C) systems. New designs are evolving with cathode ray tube (CRT)-based control rooms, more automation, and better logical information for the human operators. As these new advanced systems are developed, various decisions must be made about the degree of automation and the human-to-machine interface. Different stages of the development of control automation and of advanced digital systems can be found in various countries. The purpose of this technology assessment is to make a comparative evaluation of the control and instrumentation systems that are being used for commercial nuclear power plants in Europe and the United States. This study is limited to pressurized water reactors (PWR's). Part of the evaluation includes comparisons with a previous similar study assessing Japanese technology.

Is the digitization of laparoscopic movement using accessible alternative technologies possible?

PubMed

Lorias Espinoza, Daniel; Gutiérrez Gnecchi, José Antonio; Martínez, Arturo Minor

2012-05-01

It is widely documented that laparoscopic surgeons require training, and an objective evaluation of the training that they receive. The most advanced evaluation systems integrate the digitization of the movement of laparoscopic tools. A great number of these systems, however, do not permit the use of real tools and their high cost limits their academic impact. Likewise, it is documented that new and accessible systems need to be developed. The aim of this article is to explore the possibility of digitizing the movement of laparoscopic tools in a three-dimensional workspace, using accessible alternative technology. Our proposal uses a commercial Wii video game control in conjunction with a program for determining kinematic variables during the execution of a recognition task.

Digital Sensor Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ted Quinn; Jerry Mauck; Richard Bockhorst

The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy, reliability, availability, and maintainability. This report demonstrates these benefits in direct comparisons of digital and analog sensor applications. It also addresses the qualification issues that must be addressed in the application of digital sensor technology.

The all electric airplane-benefits and challenges

NASA Technical Reports Server (NTRS)

Spitzer, C. R.; Hood, R. V.

1982-01-01

The all electric aircraft considered in the present investigation is an aircraft which has digital flight crucial controls, electromechanical actuators, and electrical secondary power. There are no hydraulic or pneumatic systems. The characteristics of an all electric aircraft are related to reduced acquisition cost, reduced weight, reduced fuel consumption, increased reliability, reduced support equipment, simpler maintenance, an expanded flight envelope, and improved survivability. An additional benefit is the dramatically increased design flexibility and mission adaptability. However, the implementation of the all electric aircraft concept requires the resolution of a number of major technology issues. Issues in the digital flight controls area are related to achieving the required levels of safety and reliability in a cost effective manner. Other challenges which have to be met are concerned with electromechanical actuators, environmental control and ice protection systems, and engine technology.

Digital microfluidics – a new paradigm for radiochemistry

PubMed Central

Keng, Pei Yuin; van Dam, R. Michael

2016-01-01

The emerging technology of digital microfluidics is opening up the possibility to perform radiochemistry at the microliter scale to produce tracers for positron emission tomography (PET) labeled with fluorine-18 or other isotopes. Working at this volume scale not only reduces reagent costs, but also improves specific activity (SA) by reduction of contamination by the stable isotope. This technology could provide a practical means to routinely prepare high SA tracers for applications such as neuroimaging, and could make it possible to routinely achieve high SA using synthesis strategies such as isotopic exchange. Reagent droplets are controlled electronically, providing high reliability, a compact control system, and flexibility for diverse syntheses with a single chip design. The compact size may enable the development of a self-shielded synthesizer that does not require a hot cell. This article reviews the progress of this technology and its application to the synthesis of PET tracers. PMID:26650206

Field-programmable analogue arrays for the sensorless control of DC motors

NASA Astrophysics Data System (ADS)

Rivera, J.; Dueñas, I.; Ortega, S.; Del Valle, J. L.

2018-02-01

This work presents the analogue implementation of a sensorless controller for direct current motors based on the super-twisting (ST) sliding mode technique, by means of field programmable analogue arrays (FPAA). The novelty of this work is twofold, first is the use of the ST algorithm in a sensorless scheme for DC motors, and the implementation method of this type of sliding mode controllers in FPAAs. The ST algorithm reduces the chattering problem produced with the deliberate use of the sign function in classical sliding mode approaches. On the other hand, the advantages of the implementation method over a digital one are that the controller is not digitally approximated, the controller gains are not fine tuned and the implementation does not require the use of analogue-to-digital and digital-to-analogue converter circuits. In addition to this, the FPAA is a reconfigurable, lower cost and power consumption technology. Simulation and experimentation results were registered, where a more accurate transient response and lower power consumption were obtained by the proposed implementation method when compared to a digital implementation. Also, a more accurate performance by the DC motor is obtained with proposed sensorless ST technique when compared with a classical sliding mode approach.

Integrated mixed signal control IC for 500-kHz switching frequency buck regulator

NASA Astrophysics Data System (ADS)

Chen, Keng; Zhang, Hong

2015-12-01

The main purpose for this work is to study the challenges of designing a digital buck regulator using pipelined analog to digital converter (ADC). Although pipelined ADC can achieve high sampling speed, it will introduce additional phase lag to the buck circuit. Along with the latency brought by processing time of additional digital circuits, as well as the time delay associated with the switching frequency, the closed loop will be unstable; moreover, raw ADC outputs have low signal-to-noise ratio, which usually need back-end calibration. In order to compensate these phase lag and make control loop unconditional stable, as well as boost up signal-to-noise ratio of the ADC block with cost-efficient design, a finite impulse response filter followed by digital proportional-integral-derivative blocks were designed. All these digital function blocks were optimised with processing speed. In the system simulation, it can be found that this controller achieved output regulation within 10% of nominal 5 V output voltage under 1 A/µs load transient condition; moreover, with the soft-start method, there is no turn-on overshooting. The die size of this controller is controlled within 3 mm2 by using 180 nm CMOS technology.

Method for the visualization of landform by mapping using low altitude UAV application

NASA Astrophysics Data System (ADS)

Sharan Kumar, N.; Ashraf Mohamad Ismail, Mohd; Sukor, Nur Sabahiah Abdul; Cheang, William

2018-05-01

Unmanned Aerial Vehicle (UAV) and Digital Photogrammetry are evolving drastically in mapping technology. The significance and necessity for digital landform mapping are developing with years. In this study, a mapping workflow is applied to obtain two different input data sets which are the orthophoto and DSM. A fine flying technology is used to capture Low Altitude Aerial Photography (LAAP). Low altitude UAV (Drone) with the fixed advanced camera was utilized for imagery while computerized photogrammetry handling using Photo Scan was applied for cartographic information accumulation. The data processing through photogrammetry and orthomosaic processes is the main applications. High imagery quality is essential for the effectiveness and nature of normal mapping output such as 3D model, Digital Elevation Model (DEM), Digital Surface Model (DSM) and Ortho Images. The exactitude of Ground Control Points (GCP), flight altitude and the resolution of the camera are essential for good quality DEM and Orthophoto.

Opportunities and Constraints in Disseminating Qualitative Research in Web 2.0 Virtual Environments.

PubMed

Hays, Charles A; Spiers, Judith A; Paterson, Barbara

2015-11-01

The Web 2.0 digital environment is revolutionizing how users communicate and relate to each other, and how information is shared, created, and recreated within user communities. The social media technologies in the Web 2.0 digital ecosystem are fundamentally changing the opportunities and dangers in disseminating qualitative health research. The social changes influenced by digital innovations shift dissemination from passive consumption to user-centered, apomediated cooperative approaches, the features of which are underutilized by many qualitative researchers. We identify opportunities new digital media presents for knowledge dissemination activities including access to wider audiences with few gatekeeper constraints, new perspectives, and symbiotic relationships between researchers and users. We also address some of the challenges in embracing these technologies including lack of control, potential for unethical co-optation of work, and cyberbullying. Finally, we offer solutions to enhance research dissemination in sustainable, ethical, and effective strategies. © The Author(s) 2015.

Reducing the Need for Personal Supports among Workers with Autism Using an iPod Touch as an Assistive Technology: Delayed Randomized Control Trial

ERIC Educational Resources Information Center

Gentry, Tony; Kriner, Richard; Sima, Adam; McDonough, Jennifer; Wehman, Paul

2015-01-01

Personal digital assistants (PDAs) are versatile task organizers that hold promise as assistive technologies for people with cognitive-behavioral challenges. This delayed randomized controlled trial compared two groups of adult workers with autism spectrum disorder (ASD) to determine whether the use of an Apple iPod Touch PDA as a vocational…

A Qualitative Assessment of Current CCF Guidance Based on a Review of Safety System Digital Implementation Changes with Evolving Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korsah, Kofi; Muhlheim, Michael David; Wood, Richard

The US Nuclear Regulatory Commission (NRC) is initiating a new rulemaking project to develop a digital system common-cause failure (CCF) rule. This rulemaking will review and modify or affirm the NRC's current digital system CCF policy as discussed in the Staff Requirements Memorandum to the Secretary of the Commission, Office of the NRC (SECY) 93-087, Policy, Technical, and Licensing Issues Pertaining to Evolutionary and Advanced Light Water Reactor (ALWR) Designs, and Branch Technical Position (BTP) 7-19, Guidance on Evaluation of Defense-in-Depth and Diversity in Digital Computer-Based Instrumentation and Control Systems, as well as Chapter 7, Instrumentation and Controls, in NRCmore » Regulatory Guide (NUREG)-0800, Standard Review Plan for Review of Safety Analysis Reports for Nuclear Power Plants (ML033580677). The Oak Ridge National Laboratory (ORNL) is providing technical support to the NRC staff on the CCF rulemaking, and this report is one of several providing the technical basis to inform NRC staff members. For the task described in this report, ORNL examined instrumentation and controls (I&C) technology implementations in nuclear power plants in the light of current CCF guidance. The intent was to assess whether the current position on CCF is adequate given the evolutions in digital safety system implementations and, if gaps in the guidance were found, to provide recommendations as to how these gaps could be closed.« less

Flight Test Results for the F-16XL With a Digital Flight Control System

NASA Technical Reports Server (NTRS)

Stachowiak, Susan J.; Bosworth, John T.

2004-01-01

In the early 1980s, two F-16 airplanes were modified to extend the fuselage length and incorporate a large area delta wing planform. These two airplanes, designated the F-16XL, were designed by the General Dynamics Corporation (now Lockheed Martin Tactical Aircraft Systems) (Fort Worth, Texas) and were prototypes for a derivative fighter evaluation program conducted by the United States Air Force. Although the concept was never put into production, the F-16XL prototypes provided a unique planform for testing concepts in support of future high-speed supersonic transport aircraft. To extend the capabilities of this testbed vehicle the F-16XL ship 1 aircraft was upgraded with a digital flight control system. The added flexibility of a digital flight control system increases the versatility of this airplane as a testbed for aerodynamic research and investigation of advanced technologies. This report presents the handling qualities flight test results covering the envelope expansion of the F-16XL with the digital flight control system.

Social Autonomy and Heteronomy in the Age of ICT: The Digital Pharmakon and the (Dis)Empowerment of the General Intellect.

PubMed

Lemmens, Pieter

2017-01-01

'The art of living with ICTs (information and communication technologies)' today not only means finding new ways to cope, interact and create new lifestyles on the basis of the new digital (network) technologies individually , as 'consumer-citizens'. It also means inventing new modes of living, producing and, not in the least place, struggling collectively , as workers and producers. As the so-called digital revolution unfolds in the context of a neoliberal cognitive and consumerist capitalism, its 'innovations' are predominantly employed to modulate and control both production processes and consumer behavior in view of the overall goal of extracting surplus value. Today, the digital networks overwhelmingly destroy social autonomy, instead engendering increasing social heteronomy and proletarianization. Yet it is these very networks themselves, as technical pharmaka in the sense of French 'technophilosopher' Bernard Stiegler, that can be employed as no other to struggle against this tendency. This paper briefly explores this possibility by reflecting upon current diagnoses of our 'technological situation' by some exemplary post-operaist Marxists from a Stieglerian, pharmacological perspective.

The Impact of Developing Technology on Media Communications.

ERIC Educational Resources Information Center

MacDonald, Lindsay W.

1997-01-01

Examines changes in media communications resulting from new information technologies: communications technologies (networks, World Wide Web, digital set-top box); graphic arts (digital photography, CD and digital archives, desktop design and publishing, printing technology); television and video (digital editing, interactive television, news and…

Center for Coastline Security Technology, Year 3

DTIC Science & Technology

2008-05-01

Polarization control for 3D Imaging with the Sony SRX-R105 Digital Cinema Projectors 3.4 HDMAX Camera and Sony SRX-R105 Projector Configuration for 3D...HDMAX Camera Pair Figure 3.2 Sony SRX-R105 Digital Cinema Projector Figure 3.3 Effect of camera rotation on projected overlay image. Figure 3.4...system that combines a pair of FAU’s HD-MAX video cameras with a pair of Sony SRX-R105 digital cinema projectors for stereo imaging and projection

Impact of digital systems technology on man-vehicle systems research

NASA Technical Reports Server (NTRS)

Bretoi, R. N.

1983-01-01

The present study, based on a NASA technology assessment, examines the effect of new technologies on trends in crew-systems design and their implications from the vantage point of man-vehicle systems research. Those technologies that are most relevant to future trends in crew-systems design are considered along with problems associated with the introduction of rapidly changing technologies and systems concepts from a human-factors point of view. The technologies discussed include information processing, displays and controls, flight and propulsion control, flight and systems management, air traffic control, training and simulation, and flight and resource management. The historical evolution of cockpit systems design is used to illustrate past and possible future trends in man-vehicle systems research.

Digital Technologies as Education Innovation at Universities

ERIC Educational Resources Information Center

Kryukov, Vladimir; Gorin, Alexey

2017-01-01

This paper analyses the use of digital technology-based education innovations in higher education. It demonstrated that extensive implementation of digital technologies in universities is the main factor conditioning the acceleration of innovative changes in educational processes, while digital technologies themselves become one of the key…

Exploring Doctoral Students' Use of Digital Technologies: What Do They Use Them for and Why?

ERIC Educational Resources Information Center

Gouseti, Anastasia

2017-01-01

Digital technologies now form an integral feature of the university student experience and there is a range of studies that explore digital technology use within a higher education context. However, very few of these studies focus on how doctoral students engage with digital technologies. This article aims to throw light on the digital practices…

From Doing Digital to Being Digital: Exploring Workplace Adoption of Technology in the Age of Digital Disruption

ERIC Educational Resources Information Center

Murdoch, Donna; Fichter, Rachel

2017-01-01

In this article, it is explored how digital transformation is reshaping existing conceptions of technology adoption in the workplace and, as part of this, why the adoption of enterprise technology often lags behind consumer technology. The effect of business intractability towards technological advancement is examined. Also, the inability to…

Effective Use of Digital Technologies of High School Teachers as Digital Immigrants in Six Rural Public Schools

ERIC Educational Resources Information Center

Pattee, Andy

2012-01-01

Problem: A widening experiential gap of effective use of technology in K-12 schools between "digital immigrants" and "digital natives" (Prensky, 2001) is becoming more evident as digital natives become classroom teachers and showcase pedagogical strategies with digital technologies. There is a dearth of research on digital…

Flexible digital x-ray technology for far-forward remote diagnostic and conformal x-ray imaging applications

NASA Astrophysics Data System (ADS)

Smith, Joseph; Marrs, Michael; Strnad, Mark; Apte, Raj B.; Bert, Julie; Allee, David; Colaneri, Nicholas; Forsythe, Eric; Morton, David

2013-05-01

Today's flat panel digital x-ray image sensors, which have been in production since the mid-1990s, are produced exclusively on glass substrates. While acceptable for use in a hospital or doctor's office, conventional glass substrate digital x-ray sensors are too fragile for use outside these controlled environments without extensive reinforcement. Reinforcement, however, significantly increases weight, bulk, and cost, making them impractical for far-forward remote diagnostic applications, which demand rugged and lightweight x-ray detectors. Additionally, glass substrate x-ray detectors are inherently rigid. This limits their use in curved or bendable, conformal x-ray imaging applications such as the non-destructive testing (NDT) of oil pipelines. However, by extending low-temperature thin-film transistor (TFT) technology previously demonstrated on plastic substrate- based electrophoretic and organic light emitting diode (OLED) flexible displays, it is now possible to manufacture durable, lightweight, as well as flexible digital x-ray detectors. In this paper, we discuss the principal technical approaches used to apply flexible display technology to two new large-area flexible digital x-ray sensors for defense, security, and industrial applications and demonstrate their imaging capabilities. Our results include a 4.8″ diagonal, 353 x 463 resolution, flexible digital x-ray detector, fabricated on a 6″ polyethylene naphthalate (PEN) plastic substrate; and a larger, 7.9″ diagonal, 720 x 640 resolution, flexible digital x-ray detector also fabricated on PEN and manufactured on a gen 2 (370 x 470 mm) substrate.

Access to digital technology among families coming to urban pediatric primary care clinics.

PubMed

Demartini, Tori L; Beck, Andrew F; Klein, Melissa D; Kahn, Robert S

2013-07-01

Digital technologies offer new platforms for health promotion and disease management. Few studies have evaluated the use of digital technology among families receiving care in an urban pediatric primary care setting. A self-administered survey was given to a convenience sample of caregivers bringing their children to 2 urban pediatric primary care centers in spring 2012. The survey assessed access to home Internet, e-mail, smartphone, and social media (Facebook and Twitter). A "digital technology" scale (0-4) quantified the number of available digital technologies and connections. Frequency of daily use and interest in receiving medical information digitally were also assessed. The survey was completed by 257 caregivers. The sample was drawn from a clinical population that was 73% African American and 92% Medicaid insured with a median patient age of 2.9 years (interquartile range 0.8-7.4). Eighty percent of respondents reported having Internet at home, and 71% had a smartphone. Ninety-one percent reported using e-mail, 78% Facebook, and 27% Twitter. Ninety-seven percent scored ≥1 on the digital technology scale; 49% had a digital technology score of 4. The digital technology score was associated with daily use of digital media in a graded fashion (P < .0001). More than 70% of respondents reported that they would use health care information supplied digitally if approved by their child's medical provider. Caregivers in an urban pediatric primary care setting have access to and frequently use digital technologies. Digital connections may help reach a traditionally hard-to-reach population.

Long-Term Instrumentation, Information, and Control Systems (II&C) Modernization Future Vision and Strategy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kenneth Thomas

2012-02-01

Life extension beyond 60 years for the U.S operating nuclear fleet requires that instrumentation and control (I&C) systems be upgraded to address aging and reliability concerns. It is impractical for the legacy systems based on 1970's vintage technology operate over this extended time period. Indeed, utilities have successfully engaged in such replacements when dictated by these operational concerns. However, the replacements have been approached in a like-for-like manner, meaning that they do not take advantage of the inherent capabilities of digital technology to improve business functions. And so, the improvement in I&C system performance has not translated to bottom-line performancemore » improvement for the fleet. Therefore, wide-scale modernization of the legacy I&C systems could prove to be cost-prohibitive unless the technology is implemented in a manner to enable significant business innovation as a means of off-setting the cost of upgrades. A Future Vision of a transformed nuclear plant operating model based on an integrated digital environment has been developed as part of the Advanced Instrumentation, Information, and Control (II&C) research pathway, under the Light Water Reactor (LWR) Sustainability Program. This is a research and development program sponsored by the U.S. Department of Energy (DOE), performed in close collaboration with the nuclear utility industry, to provide the technical foundations for licensing and managing the long-term, safe and economical operation of current nuclear power plants. DOE's program focus is on longer-term and higher-risk/reward research that contributes to the national policy objectives of energy security and environmental security . The Advanced II&C research pathway is being conducted by the Idaho National Laboratory (INL). The Future Vision is based on a digital architecture that encompasses all aspects of plant operations and support, integrating plant systems, plant work processes, and plant workers in a seamless digital environment to enhance nuclear safety, increase productivity, and improve overall plant performance. The long-term goal is to transform the operating model of the nuclear power plants (NPP)s from one that is highly reliant on a large staff performing mostly manual activities to an operating model based on highly integrated technology with a smaller staff. This digital transformation is critical to addressing an array of issues facing the plants, including aging of legacy analog systems, potential shortage of technical workers, ever-increasing expectations for nuclear safety improvement, and relentless pressure to reduce cost. The Future Vision is based on research is being conducted in the following major areas of plant function: (1) Highly integrated control rooms; (2) Highly automated plant; (3) Integrated operations; (4) Human performance improvement for field workers; and (5) Outage safety and efficiency. Pilot projects will be conducted in each of these areas as the means for industry to collectively integrate these new technologies into nuclear plant work activities. The pilot projects introduce new digital technologies into the nuclear plant operating environment at host operating plants to demonstrate and validate them for production usage. In turn, the pilot project technologies serve as the stepping stones to the eventual seamless digital environment as described in the Future Vision.« less

Long-Term Instrumentation, Information, and Control Systems (II&C) Modernization Future Vision and Strategy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kenneth Thomas; Bruce Hallbert

2013-02-01

Life extension beyond 60 years for the U.S operating nuclear fleet requires that instrumentation and control (I&C) systems be upgraded to address aging and reliability concerns. It is impractical for the legacy systems based on 1970’s vintage technology operate over this extended time period. Indeed, utilities have successfully engaged in such replacements when dictated by these operational concerns. However, the replacements have been approached in a like-for-like manner, meaning that they do not take advantage of the inherent capabilities of digital technology to improve business functions. And so, the improvement in I&C system performance has not translated to bottom-line performancemore » improvement for the fleet. Therefore, wide-scale modernization of the legacy I&C systems could prove to be cost-prohibitive unless the technology is implemented in a manner to enable significant business innovation as a means of off-setting the cost of upgrades. A Future Vision of a transformed nuclear plant operating model based on an integrated digital environment has been developed as part of the Advanced Instrumentation, Information, and Control (II&C) research pathway, under the Light Water Reactor (LWR) Sustainability Program. This is a research and development program sponsored by the U.S. Department of Energy (DOE), performed in close collaboration with the nuclear utility industry, to provide the technical foundations for licensing and managing the long-term, safe and economical operation of current nuclear power plants. DOE’s program focus is on longer-term and higher-risk/reward research that contributes to the national policy objectives of energy security and environmental security . The Advanced II&C research pathway is being conducted by the Idaho National Laboratory (INL). The Future Vision is based on a digital architecture that encompasses all aspects of plant operations and support, integrating plant systems, plant work processes, and plant workers in a seamless digital environment to enhance nuclear safety, increase productivity, and improve overall plant performance. The long-term goal is to transform the operating model of the nuclear power plants (NPP)s from one that is highly reliant on a large staff performing mostly manual activities to an operating model based on highly integrated technology with a smaller staff. This digital transformation is critical to addressing an array of issues facing the plants, including aging of legacy analog systems, potential shortage of technical workers, ever-increasing expectations for nuclear safety improvement, and relentless pressure to reduce cost. The Future Vision is based on research is being conducted in the following major areas of plant function: 1. Highly integrated control rooms 2. Highly automated plant 3. Integrated operations 4. Human performance improvement for field workers 5. Outage safety and efficiency. Pilot projects will be conducted in each of these areas as the means for industry to collectively integrate these new technologies into nuclear plant work activities. The pilot projects introduce new digital technologies into the nuclear plant operating environment at host operating plants to demonstrate and validate them for production usage. In turn, the pilot project technologies serve as the stepping stones to the eventual seamless digital environment as described in the Future Vision.« less

High quality digital holographic reconstruction on analog film

NASA Astrophysics Data System (ADS)

Nelsen, B.; Hartmann, P.

2017-05-01

High quality real-time digital holographic reconstruction, i.e. at 30 Hz frame rates, has been at the forefront of research and has been hailed as the holy grail of display systems. While these efforts have produced a fascinating array of computer algorithms and technology, many applications of reconstructing high quality digital holograms do not require such high frame rates. In fact, applications such as 3D holographic lithography even require a stationary mask. Typical devices used for digital hologram reconstruction are based on spatial-light-modulator technology and this technology is great for reconstructing arbitrary holograms on the fly; however, it lacks the high spatial resolution achievable by its analog counterpart, holographic film. Analog holographic film is therefore the method of choice for reconstructing highquality static holograms. The challenge lies in taking a static, high-quality digitally calculated hologram and effectively writing it to holographic film. We have developed a theoretical system based on a tunable phase plate, an intensity adjustable high-coherence laser and a slip-stick based piezo rotation stage to effectively produce a digitally calculated hologram on analog film. The configuration reproduces the individual components, both the amplitude and phase, of the hologram in the Fourier domain. These Fourier components are then individually written on the holographic film after interfering with a reference beam. The system is analogous to writing angularly multiplexed plane waves with individual component phase control.

Simulation of digital mammography images

NASA Astrophysics Data System (ADS)

Workman, Adam

2005-04-01

A number of different technologies are available for digital mammography. However, it is not clear how differences in the physical performance aspects of the different imaging technologies affect clinical performance. Randomised controlled trials provide a means of gaining information on clinical performance however do not provide direct comparison of the different digital imaging technologies. This work describes a method of simulating the performance of different digital mammography systems. The method involves modifying the imaging performance parameters of images from a small field of view (SFDM), high resolution digital imaging system used for spot imaging. Under normal operating conditions this system produces images with higher signal-to-noise ratio (SNR) over a wide spatial frequency range than current full field digital mammography (FFDM) systems. The SFDM images can be 'degraded" by computer processing to simulate the characteristics of a FFDM system. Initial work characterised the physical performance (MTF, NPS) of the SFDM detector and developed a model and method for simulating signal transfer and noise properties of a FFDM system. It was found that the SNR properties of the simulated FFDM images were very similar to those measured from an actual FFDM system verifying the methodology used. The application of this technique to clinical images from the small field system will allow the clinical performance of different FFDM systems to be simulated and directly compared using the same clinical image datasets.

Administrative Services Division - Alaska Department of Law

Science.gov Websites

Attorney General Opinions Executive Branch Ethics Criminal Justice Alaska Medicaid Fraud Control Anchorage digital communication. Department-wide Information Technology issues, strategic planning, resource

Preservice Teachers' Perceptions of Using Digital Technologies in Literacy Instruction

ERIC Educational Resources Information Center

Pierczynski, Melissa

2015-01-01

In order to best prepare our preservice teachers to incorporate digital technologies into future literacy instruction, we must first explore how they perceive implementation of digital technologies in literacy instruction. Limited research exists which examines the employment of digital technologies in literacy instruction, and even less considers…

Interactive Digital Technologies' Use in Southwest Nigerian Universities

ERIC Educational Resources Information Center

Agbatogun, Alaba Olaoluwakotansibe

2013-01-01

The interactive digital technologies in education is an effective means used to widen educational opportunities. However, many faculty members do not use or adopt digital technologies as instructional tools. The purpose of this study was to predict faculty members' use of digital technologies in Nigerian Universities. 492 university lecturers from…

Low Power Camera-on-a-Chip Using CMOS Active Pixel Sensor Technology

NASA Technical Reports Server (NTRS)

Fossum, E. R.

1995-01-01

A second generation image sensor technology has been developed at the NASA Jet Propulsion Laboratory as a result of the continuing need to miniaturize space science imaging instruments. Implemented using standard CMOS, the active pixel sensor (APS) technology permits the integration of the detector array with on-chip timing, control and signal chain electronics, including analog-to-digital conversion.

Social Construction of Authorized Users in the Digital Age

ERIC Educational Resources Information Center

Zhu, Xiaohua; Eschenfelder, Kristin R.

2010-01-01

This paper analyzes changes to the definitions of "authorized users" contained in electronic resources licenses and embedded in access control technologies from the mid-1990s to the present. In analyzing changes to the license and technology-based definitions, it tracks shifts in major stakeholders' perceptions of authorized users and…

Controlled power delivery for super-resolution imaging of biological samples using digital micromirror device

NASA Astrophysics Data System (ADS)

Valiya Peedikakkal, Liyana; Cadby, Ashley

2017-02-01

Localization based super resolution images of a biological sample is generally achieved by using high power laser illumination with long exposure time which unfortunately increases photo-toxicity of a sample, making super resolution microscopy, in general, incompatible with live cell imaging. Furthermore, the limitation of photobleaching reduces the ability to acquire time lapse images of live biological cells using fluorescence microscopy. Digital Light Processing (DLP) technology can deliver light at grey scale levels by flickering digital micromirrors at around 290 Hz enabling highly controlled power delivery to samples. In this work, Digital Micromirror Device (DMD) is implemented in an inverse Schiefspiegler telescope setup to control the power and pattern of illumination for super resolution microscopy. We can achieve spatial and temporal patterning of illumination by controlling the DMD pixel by pixel. The DMD allows us to control the power and spatial extent of the laser illumination. We have used this to show that we can reduce the power delivered to the sample to allow for longer time imaging in one area while achieving sub-diffraction STORM imaging in another using higher power densities.

Continuous-tone applications in digital hard-copy output devices

NASA Astrophysics Data System (ADS)

Saunders, Jeffrey C.

1990-11-01

Dye diffusion technology has made a recent entry into the hardcopy printer arena making it now possible to achieve near-photographic quality images from digital raster image data. Whereas the majority of low cost printers utilizing ink-jet, thermal wax, or dotmatrix technologies advertise high resolution printheads, the restrictions which dithering algorithms apply to these inherently binary printing systems force them to sacrifice spatial resolution capability for tone scale reproduction. Dye diffusion technology allows a fully continuous range of density at each pixel location thus preserving the full spatial resolution capability of the printhead; spatial resolution is not sacrificed for tone scale. This results in images whose quality is far superior to the ink-jet or wax-transfer products; image quality so high in fact, to the unaided eye, dye diffusion images are indistinguishable from their silver-halide counterparts. Eastman Kodak Co. offers a highly refined application of dye diffusion technology in the Kodak XL 7700 Digital Continuous Tone Printer and Kodak EKTATHERM media products. The XL . 7700 Printer represents a serious alternative to expensive laser-based film recorders for applications which require high quality image output from digital data files. This paper presents an explanation of dye diffusion printing, what distinguishes it from other technologies, sensitometric control and image quality parameters, and applications within the industry, particularly that of Airborne Reconnaissance and Remote Sensing.

Digital Natives and Digital Immigrants: Teaching with Technology

ERIC Educational Resources Information Center

Martin, Ellen Marie Peterson

2011-01-01

Education is witnessing an increasing demand for technology use in the classroom. At the same time, new teachers are entering the profession in high numbers, some being labeled as "Digital Natives" while others are labeled "Digital Immigrants". This qualitative case study investigated the technology practices of Digital Native and Digital…

The value of early flight evaluation of propulsion concepts using the NASA F-15 research airplane

NASA Technical Reports Server (NTRS)

Burcham, Frank W., Jr.; Ray, Ronald J.

1987-01-01

The value of early flight evaluation of propulsion and propulsion control concepts was demonstrated on the NASA F-15 airplane in programs such as highly integrated digital electronic control (HIDEC), the F100 engine model derivative (EMD), and digital electronic engine control (DEEC). (In each case, the value of flight demonstration was conclusively demonstrated). This paper described these programs, and discusses the results that were not expected, based on ground test or analytical prediction. The role of flight demonstration in facilitating transfer of technology from the laboratory to operational airplanes is discussed.

Optical technology for flight control systems

NASA Technical Reports Server (NTRS)

Mayanagi, M.

1986-01-01

Optical applications to the flight control system including optical data bus, sensors, and transducers are analyzed. Examples of optical data bus include airborne light optical fiber technology (ALOFT), F-5E, YA-7D, MIL-STD-1553 fiber optic data bus and NAL-optic data bus. This NAL-optic data bus is applied to STOL, and its characteristics are stressed. Principles and advantages of optical pulse-digital transducers are discussed.

Remote Patient Monitoring via Non-Invasive Digital Technologies: A Systematic Review

PubMed Central

Tran, Melody; Angelaccio, Michele; Arcona, Steve

2017-01-01

Abstract Background: We conducted a systematic literature review to identify key trends associated with remote patient monitoring (RPM) via noninvasive digital technologies over the last decade. Materials and Methods: A search was conducted in EMBASE and Ovid MEDLINE. Citations were screened for relevance against predefined selection criteria based on the PICOTS (Population, Intervention, Comparator, Outcomes, Timeframe, and Study Design) format. We included studies published between January 1, 2005 and September 15, 2015 that used RPM via noninvasive digital technology (smartphones/personal digital assistants [PDAs], wearables, biosensors, computerized systems, or multiple components of the formerly mentioned) in evaluating health outcomes compared to standard of care or another technology. Studies were quality appraised according to Critical Appraisal Skills Programme. Results: Of 347 articles identified, 62 met the selection criteria. Most studies were randomized control trials with older adult populations, small sample sizes, and limited follow-up. There was a trend toward multicomponent interventions (n = 26), followed by smartphones/PDAs (n = 12), wearables (n = 11), biosensor devices (n = 7), and computerized systems (n = 6). Another key trend was the monitoring of chronic conditions, including respiratory (23%), weight management (17%), metabolic (18%), and cardiovascular diseases (16%). Although substantial diversity in health-related outcomes was noted, studies predominantly reported positive findings. Conclusions: This review will help decision makers develop a better understanding of the current landscape of peer-reviewed literature, demonstrating the utility of noninvasive RPM in various patient populations. Future research is needed to determine the effectiveness of RPM via noninvasive digital technologies in delivering patient healthcare benefits and the feasibility of large-scale implementation. PMID:27116181

Computer Sciences and Data Systems, volume 2

NASA Technical Reports Server (NTRS)

1987-01-01

Topics addressed include: data storage; information network architecture; VHSIC technology; fiber optics; laser applications; distributed processing; spaceborne optical disk controller; massively parallel processors; and advanced digital SAR processors.

Guidance, Navigation and Control Digital Emulation Technology Laboratory. Volume 1. Part 3. Task 1: Digital Emulation Technology Laboratory

DTIC Science & Technology

1991-09-27

ISTT IEXIT IGO MAGV TGII ROLLERI YAWER LA !10 TRMTGO TGE 1 TGE2ALI IBURNI ACQD UVs MVS CMMD VCMD IFTAB TFTAB ACSLEV DTOFFV IVTAB TB URNM TI MONVI TVTAB...Volume 1, Part 3 C b inertdfatal loup ndxjust compu ed . Missile states must not CI C transition has occurred since the last C C integration step . The...SUBROUTINE RESP2R ( DT,WD,ZD,CILL,CIL,CI., COLL ,COL,CO) C C SUBROUTINE NAME : RESP2R C C AUTHOR(S) :D. F. SMITH C C FUNCTION Given a second

Educational-research laboratory "electric circuits" on the base of digital technologies

NASA Astrophysics Data System (ADS)

Koroteyev, V. I.; Florentsev, V. V.; Florentseva, N. I.

2017-01-01

The problem of research activity of trainees' activation in the educational-research laboratory "Electric Circuits" using innovative methodological solutions and digital technologies is considered. The main task is in creation of the unified experimental research information-educational environment "Electrical Engineering". The problems arising during the developing and application of the modern software and hardware, experimental and research stands and digital control and measuring systems are presented. This paper presents the main stages of development and creation of educational-research laboratory "Electrical Circuits" at the Department of Electrical Engineering of NRNU MEPhI. The authors also consider the analogues of the described research complex offered by various educational institutions and companies. The analysis of their strengths and weaknesses, on which the advantages of the proposed solution are based, is held.

Airborne Digital Sensor System and GPS-aided inertial technology for direct geopositioning in rough terrain

USGS Publications Warehouse

Sanchez, Richard D.

2004-01-01

High-resolution airborne digital cameras with onboard data collection based on the Global Positioning System (GPS) and inertial navigation systems (INS) technology may offer a real-time means to gather accurate topographic map information by reducing ground control and eliminating aerial triangulation. Past evaluations of this integrated system over relatively flat terrain have proven successful. The author uses Emerge Digital Sensor System (DSS) combined with Applanix Corporation?s Position and Orientation Solutions for Direct Georeferencing to examine the positional mapping accuracy in rough terrain. The positional accuracy documented in this study did not meet large-scale mapping requirements owing to an apparent system mechanical failure. Nonetheless, the findings yield important information on a new approach for mapping in Antarctica and other remote or inaccessible areas of the world.

Transitioning towards the Digital Native: Examining Digital Technologies, Video Games, and Learning

ERIC Educational Resources Information Center

Salomon, John

2010-01-01

Although digital technologies have become commonplace among people who grew up around them, little is known about the effect that such technology will have on learners or its impact on traditional methods of educational delivery. This dissertation examines how certain technologies affect digital natives and seeks to understand specific…

Redefining Student Affairs through Digital Technology: A Ten-Year Historiography of Digital Technology Use by Student Affairs Administrators

ERIC Educational Resources Information Center

Cabellon, Edmund T.

2016-01-01

The student affairs profession is at a crossroads (Torres & Walbert, 2010) given digital technology's growth and the academy's administrative expansion (Bowen, 2013). Student affairs administrators must simultaneously respond to digital technology's implications in students' lives (Kirschner & Karpinski, 2010) and to new state and federal…

Decoding the TV Remote Control.

ERIC Educational Resources Information Center

O'Connell, James

2000-01-01

Describes how to observe the pulse structure of the infrared signals from the light-emitting diode in a TV remote control. This exercise in decoding infrared digital signals provides an opportunity to discuss semiconductors, photonics technology, cryptology, and the physics of how things work. (WRM)

Initial flight qualification and operational maintenance of X-29A flight software

NASA Technical Reports Server (NTRS)

Earls, Michael R.; Sitz, Joel R.

1989-01-01

A discussion is presented of some significant aspects of the initial flight qualification and operational maintenance of the flight control system softward for the X-29A technology demonstrator. Flight qualification and maintenance of complex, embedded flight control system software poses unique problems. The X-29A technology demonstrator aircraft has a digital flight control system which incorporates functions generally considered too complex for analog systems. Organizational responsibilities, software assurance issues, tools, and facilities are discussed.

Simulink-aided Design and Implementation of Sensorless BLDC Motor Digital Control System

NASA Astrophysics Data System (ADS)

Zhilenkov, A. A.; Tsvetkov, Y. N.; Chistov, V. B.; Nyrkov, A. P.; Sokolov, S. S.

2017-07-01

The paper describes the process of creating of brushless direct current motor’s digital control system. The target motor has no speed sensor, so back-EMF method is used for commutation control. Authors show how to model the control system in MatLab/Simulink and to test it onboard STM32F4 microcontroller.This technology allows to create the most flexible system, which will control possible with a personal computer by communication lines. It is possible to examine the signals in the circuit of the actuator without any external measuring instruments - testers, oscilloscopes, etc. - and output waveforms and measured values of signals directly on the host PC.

Space shuttle main engine controller

NASA Technical Reports Server (NTRS)

Mattox, R. M.; White, J. B.

1981-01-01

A technical description of the space shuttle main engine controller, which provides engine checkout prior to launch, engine control and monitoring during launch, and engine safety and monitoring in orbit, is presented. Each of the major controller subassemblies, the central processing unit, the computer interface electronics, the input electronics, the output electronics, and the power supplies are described and discussed in detail along with engine and orbiter interfaces and operational requirements. The controller represents a unique application of digital concepts, techniques, and technology in monitoring, managing, and controlling a high performance rocket engine propulsion system. The operational requirements placed on the controller, the extremely harsh operating environment to which it is exposed, and the reliability demanded, result in the most complex and rugged digital system ever designed, fabricated, and flown.

Improving Hypertension Control and Patient Engagement Using Digital Tools.

PubMed

Milani, Richard V; Lavie, Carl J; Bober, Robert M; Milani, Alexander R; Ventura, Hector O

2017-01-01

Hypertension is present in 30% of the adult US population and is a major contributor to cardiovascular disease. The established office-based approach yields only 50% blood pressure control rates and low levels of patient engagement. Available home technology now provides accurate, reliable data that can be transmitted directly to the electronic medical record. We evaluated blood pressure control in 156 patients with uncontrolled hypertension enrolled into a home-based digital-medicine blood pressure program and compared them with 400 patients (matched to age, sex, body mass index, and blood pressure) in a usual-care group after 90 days. Digital-medicine patients completed questionnaires online, were asked to submit at least one blood pressure reading/week, and received medication management and lifestyle recommendations via a clinical pharmacist and a health coach. Blood pressure units were commercially available that transmitted data directly to the electronic medical record. Digital-medicine patients averaged 4.2 blood pressure readings per week. At 90 days, 71% of digital-medicine vs 31% of usual-care patients had achieved target blood pressure control. Mean decrease in systolic/diastolic blood pressure was 14/5 mm Hg in digital medicine, vs 4/2 mm Hg in usual care (P < .001). Excess sodium consumption decreased from 32% to 8% in the digital-medicine group (P = .004). Mean patient activation increased from 41.9 to 44.1 (P = .008), and the percentage of patients with low patient activation decreased from 15% to 6% (P = .03) in the digital-medicine group. A digital hypertension program is feasible and associated with significant improvement in blood pressure control rates and lifestyle change. Utilization of a virtual health intervention using connected devices improves patient activation and is well accepted by patients. Copyright © 2016 Elsevier Inc. All rights reserved.

Digital technology and human development: a charter for nature conservation.

PubMed

Maffey, Georgina; Homans, Hilary; Banks, Ken; Arts, Koen

2015-11-01

The application of digital technology in conservation holds much potential for advancing the understanding of, and facilitating interaction with, the natural world. In other sectors, digital technology has long been used to engage communities and share information. Human development-which holds parallels with the nature conservation sector-has seen a proliferation of innovation in technological development. Throughout this Perspective, we consider what nature conservation can learn from the introduction of digital technology in human development. From this, we derive a charter to be used before and throughout project development, in order to help reduce replication and failure of digital innovation in nature conservation projects. We argue that the proposed charter will promote collaboration with the development of digital tools and ensure that nature conservation projects progress appropriately with the development of new digital technologies.

A digital optical phase-locked loop for diode lasers based on field programmable gate array.

PubMed

Xu, Zhouxiang; Zhang, Xian; Huang, Kaikai; Lu, Xuanhui

2012-09-01

We have designed and implemented a highly digital optical phase-locked loop (OPLL) for diode lasers in atom interferometry. The three parts of controlling circuit in this OPLL, including phase and frequency detector (PFD), loop filter and proportional integral derivative (PID) controller, are implemented in a single field programmable gate array chip. A structure type compatible with the model MAX9382∕MCH12140 is chosen for PFD and pipeline and parallelism technology have been adapted in PID controller. Especially, high speed clock and twisted ring counter have been integrated in the most crucial part, the loop filter. This OPLL has the narrow beat note line width below 1 Hz, residual mean-square phase error of 0.14 rad(2) and transition time of 100 μs under 10 MHz frequency step. A main innovation of this design is the completely digitalization of the whole controlling circuit in OPLL for diode lasers.

A digital optical phase-locked loop for diode lasers based on field programmable gate array

NASA Astrophysics Data System (ADS)

Xu, Zhouxiang; Zhang, Xian; Huang, Kaikai; Lu, Xuanhui

2012-09-01

We have designed and implemented a highly digital optical phase-locked loop (OPLL) for diode lasers in atom interferometry. The three parts of controlling circuit in this OPLL, including phase and frequency detector (PFD), loop filter and proportional integral derivative (PID) controller, are implemented in a single field programmable gate array chip. A structure type compatible with the model MAX9382/MCH12140 is chosen for PFD and pipeline and parallelism technology have been adapted in PID controller. Especially, high speed clock and twisted ring counter have been integrated in the most crucial part, the loop filter. This OPLL has the narrow beat note line width below 1 Hz, residual mean-square phase error of 0.14 rad2 and transition time of 100 μs under 10 MHz frequency step. A main innovation of this design is the completely digitalization of the whole controlling circuit in OPLL for diode lasers.

Connecting across the Web: An Exploration of Student Perceptions of the Effects of Virtual Social Learning on Student Professional Skills in College

ERIC Educational Resources Information Center

LaVoy, Lynea D.

2011-01-01

The emergence of a new digital landscape coupled with the pervasive nature of digital experiences has fundamentally changed both current and future students in colleges and universities across the world. A new generation of learners has entered college armed with an understanding of technology that prepares them to have a greater control over…

Digital Voting Systems and Communication in Classroom Lectures--An Empirical Study Based around Physics Teaching at Bachelor Level at Two Danish Universities

ERIC Educational Resources Information Center

Mathiasen, Helle

2015-01-01

Studies on the use of digital voting systems in large group teaching situations have often focused on the "non-anonymity" and control and testing functions that the technology provides. There has also been some interest in how students might use their votes tactically to gain "credits". By focusing on an empirical study of…

Digital slides: present status of a tool for consultation, teaching, and quality control in pathology.

PubMed

Rocha, Rafael; Vassallo, José; Soares, Fernando; Miller, Keith; Gobbi, Helenice

2009-01-01

In the last few years, telepathology has benefited from the progress in the technology of image digitalization and transmission through the world web. The applications of telepathology and virtual imaging are more current in research and morphology teaching. In surgical pathology daily practice, this technology still has limits and is more often used for case consultation. In the present review, we intend to discuss its applications and challenges for pathologists and scientists. Much of the limitations of virtual imaging for the surgical pathologist reside in the capacity of storage of images, which so far has hindered the more widespread use of this technology. Overcoming this major drawback may revolutionize the surgical pathologist's activity and slide storing.

Adopting Digital Technologies in the Classroom: 10 Assessment Questions

ERIC Educational Resources Information Center

Staley, David J.

2004-01-01

Technology has long been a part of the classroom space. Sometime in the 1990s, the word technology was co-opted to refer only to digital tools. "Technology in the classroom" or "technology stocks" or "the dangers posed by technology" came to refer only to digital technology rather than to technology as a whole. As such, much of the discussion…

A Fully Integrated Sensor SoC with Digital Calibration Hardware and Wireless Transceiver at 2.4 GHz

PubMed Central

Kim, Dong-Sun; Jang, Sung-Joon; Hwang, Tae-Ho

2013-01-01

A single-chip sensor system-on-a-chip (SoC) that implements radio for 2.4 GHz, complete digital baseband physical layer (PHY), 10-bit sigma-delta analog-to-digital converter and dedicated sensor calibration hardware for industrial sensing systems has been proposed and integrated in a 0.18-μm CMOS technology. The transceiver's building block includes a low-noise amplifier, mixer, channel filter, receiver signal-strength indicator, frequency synthesizer, voltage-controlled oscillator, and power amplifier. In addition, the digital building block consists of offset quadrature phase-shift keying (OQPSK) modulation, demodulation, carrier frequency offset compensation, auto-gain control, digital MAC function, sensor calibration hardware and embedded 8-bit microcontroller. The digital MAC function supports cyclic redundancy check (CRC), inter-symbol timing check, MAC frame control, and automatic retransmission. The embedded sensor signal processing block consists of calibration coefficient calculator, sensing data calibration mapper and sigma-delta analog-to-digital converter with digital decimation filter. The sensitivity of the overall receiver and the error vector magnitude (EVM) of the overall transmitter are −99 dBm and 18.14%, respectively. The proposed calibration scheme has a reduction of errors by about 45.4% compared with the improved progressive polynomial calibration (PPC) method and the maximum current consumption of the SoC is 16 mA. PMID:23698271

Case Study of Apple, Inc. for Business Law Students: How Apple's Business Model Controls Digital Content through Legal and Technological Means

ERIC Educational Resources Information Center

Reder, Margo E. K.

2009-01-01

This article describes a six-week long exercise that incorporates a dynamic learning approach into an e-commerce or Internet technology business law elective course; the exercise pursues an entrepreneurial approach to the use of an appropriate business model by emphasizing the interaction between technology, business, and law. This active learning…

Advanced Physiological Estimation of Cognitive Status. Part 2

DTIC Science & Technology

2011-05-24

Neurofeedback Algorithms and Gaze Controller EEG Sensor System g.USBamp *, ** • internal 24-bit ADC and digital signal processor • 16 channels (expandable...SUBJECT TERMS EEG eye-tracking mental state estimation machine learning Leonard J. Trejo Pacific Development and Technology LLC 999 Commercial St. Palo...fatigue, overload) Technology Transfer Opportunity Technology from PDT – Methods to acquire various physiological signals ( EEG , EOG, EMG, ECG, etc

Advanced Electronic Systems. Curriculum Guide for Technology Education.

ERIC Educational Resources Information Center

Patrick, Dale R.

This curriculum for a 1-semester or 1-year course in electronics is designed to take students from basic through advanced electronic systems. It covers several electronic areas, such as digital electronics, communication electronics, industrial process control, instrumentation, programmable controllers, and robotics. The guide contains…

[Smart, Social, and Mobile: the future of Nephrology in the Era of Digital Health].

PubMed

Iannuzzella, Francesco; Murtas, Corrado; Bertolini, Riccardo; Corradini, Mattia; Pasquali, Sonia

2016-01-01

Healthcare is in the middle of a digital revolution. Physicians are adopting mobile apps that make them more effective and patients are taking to ones that give them more control over their healthcare. Mobile technology is changing Medicine. A new movement for free open access medical education (FOAMed) is growing through Social Media. E-learning is increasing access to new and exciting learning opportunities, deeply changing the traditional concept of continuous medical education. What will be the future of Nephrology in the era of Digital Health?

JPL CMOS Active Pixel Sensor Technology

NASA Technical Reports Server (NTRS)

Fossum, E. R.

1995-01-01

This paper will present the JPL-developed complementary metal- oxide-semiconductor (CMOS) active pixel sensor (APS) technology. The CMOS APS has achieved performance comparable to charge coupled devices, yet features ultra low power operation, random access readout, on-chip timing and control, and on-chip analog to digital conversion. Previously published open literature will be reviewed.

An Investigation of Pre-Service Primary School Teachers' Attitudes towards Digital Technology and Digital Citizenship Levels in Terms of Some Variables

ERIC Educational Resources Information Center

Çiftci, Serdar; Aladag, Soner

2018-01-01

This study aims at investigating the relationship between pre-service primary school teachers' attitudes towards digital technology and digital citizenship scale levels. The research was designed in descriptive survey model. The data collection tools were "Attitude Scale for Digital Technology" (ASDT) developed by Cabi (2016) and…

Business use of satellite communications

NASA Astrophysics Data System (ADS)

Edelson, B. I.; Cooper, R. S.

1982-02-01

The development, systems technology, and future applications of digital transmission systems for business use of satellite systems are explored. Intelsat currently has 22 satellites in space, applied mostly to data, telephone, and television transmission. An all digital communications network called the Integrated Services Digital Network is replacing the former, analog, systems with wideband digital transmission for voice, data, video, and industrial control information, with domestic satellites serving as the central node of transmissions in a service area. The digital systems are faster than the analog systems, and the U.S. Postal Service is developing an electronic mail system with six other countries. Various magazines are now teleprinted in various locations from broadcasts from a central source, and chain stores are employing data transmission for centralized management, inventory, and procurement.

Digital control of magnetic bearings in a cryogenic cooler

NASA Technical Reports Server (NTRS)

Feeley, J.; Law, A.; Lind, F.

1990-01-01

This paper describes the design of a digital control system for control of magnetic bearings used in a spaceborne cryogenic cooler. The cooler was developed by Philips Laboratories for the NASA Goddard Space Flight Center. Six magnetic bearing assemblies are used to levitate the piston, displacer, and counter-balance of the cooler. The piston and displacer are driven by linear motors in accordance with Stirling cycle thermodynamic principles to produce the desired cooling effect. The counter-balance is driven by a third linear motor to cancel motion induced forces that would otherwise be transmitted to the spacecraft. An analog control system is currently used for bearing control. The purpose of this project is to investigate the possibilities for improved performance using digital control. Areas for potential improvement include transient and steady state control characteristics, robustness, reliability, adaptability, alternate control modes, size, weight, and cost. The present control system is targeted for the Intel 80196 microcontroller family. The eventual introduction of application specific integrated circuit (ASIC) technology to this problem may produce a unique and elegant solution both here and in related industrial problems.

Discussion on the management system technology implementation of multimedia classrooms in the digital campus

NASA Astrophysics Data System (ADS)

Wang, Bo

2018-04-01

Based on the digitized information and network, digital campus is an integration of teaching, management, science and research, life service and technology service, and it is one of the current mainstream construction form of campus function. This paper regarded the "mobile computing" core digital environment construction development as the background, explored the multiple management system technology content design and achievement of multimedia classrooms in digital campus and scientifically proved the technology superiority of management system.

Internal health locus of control predicts willingness to track health behaviors online and with smartphone applications.

PubMed

Bennett, Brooke L; Goldstein, Carly M; Gathright, Emily C; Hughes, Joel W; Latner, Janet D

2017-12-01

Given rising technology use across all demographic groups, digital interventions offer a potential strategy for increasing access to health information and care. Research is lacking on identifying individual differences that impact willingness to use digital interventions, which may affect patient engagement. Health locus of control, the amount of control an individual believes they have over their own health, may predict willingness to use mobile health (mHealth) applications ('apps') and online trackers. A cross-sectional study (n = 276) was conducted to assess college students' health locus of control beliefs and willingness to use health apps and online trackers. Internal and powerful other health locus of control beliefs predicted willingness to use health apps and online trackers while chance health locus of control beliefs did not. Individuals with internal and powerful other health locus of control beliefs are more willing than those with chance health locus of control beliefs to utilize a form of technology to monitor or change health behaviors. Health locus of control is an easy-to-assess patient characteristic providers can measure to identify which patients are more likely to utilize mHealth apps and online trackers.

Fiber optics for advanced aircraft

NASA Technical Reports Server (NTRS)

Baumbick, Robert J.

1989-01-01

The increased use of composites makes the digital control more susceptible to electromagnetic effects. In order to provide the protection to the digital control additional shielding will be required as well as protective circuitry for the electronics. This results in increased weight and reduced reliability. The advantages that fiber optic technology provides for advanced aircraft applications is recognized. The use of optical signals to carry information between the aircraft and the control module provides immunity from contamination by electromagnetic sources as well as other important benefits such as reduced weight and volume resulting from the elimination of the shielding and the replacement of metal conductors with low weight glass fibers. In 1975 NASA began work to develop passive optical sensors for use with fiber optics in aircraft control systems. The problem now is to choose the best optical sensor concepts and evaluate them for use. In 1985 NASA and DOD entered into a joint program, Fiber Optic Control System Integration (FOCSI), to look at optical technology specifically for use in advanced aircraft systems. The results of this program are discussed. The conclusion of the study indicated that the use of fiber optic technology in advanced aircraft systems is feasible and desirable. The study pointed to a lack of available sensors from vendors capable of operating in the adverse environments of advanced aircraft.

Fiber optics for advanced aircraft

NASA Technical Reports Server (NTRS)

Baumbick, Robert J.

1988-01-01

The increased use of composites makes the digital control more susceptible to electromagnetic effects. In order to provide the protection to the digital control additional shielding will be required as well as protective circuitry for the electronics. This results in increased weight and reduced reliability. The advantages that fiber optic technology provides for advanced aircraft applications is recognized. The use of optical signals to carry information between the aircraft and the control module provides immunity from contamination by electromagnetic sources as well as other important benefits such as reduced weight and volume resulting from the elimination of the shielding and the replacement of metal conductors with low weight glass fibers. In 1975 NASA began work to develop passive optical sensors for use with fiber optics in aircraft control systems. The problem now is to choose the best optical sensor concepts and evaluate them for use. In 1985 NASA and DOD entered into a joint program, Fiber Optic Control System Integration (FOCSI), to look at optical technology specifically for use in advanced aircraft systems. The results of this program are discussed. The conclusion of the study indicated that the use of fiber optic technology in advanced aircraft systems is feasible and desirable. The study pointed to a lack of available sensors from vendors capable of operating in the adverse environments of advanced aircraft.

Re-Mixing Multimodal Resources: Multiliteracies and Digital Production in Norwegian Media Education

ERIC Educational Resources Information Center

Erstad, Ola; Gilje, Oystein; de Lange, Thomas

2007-01-01

Youngsters are increasingly using digital technologies through participation in informal settings. Schools, however, seem to be struggling with implementing digital technologies into formal school activities. With the impact of digital technologies, media education can be seen as an increasingly important "transactional learning space"…

[Application of three-dimensional digital technology in the diagnosis and treatment planning in orthodontics].

PubMed

Bai, Y X

2016-06-01

Three-dimensional(3D)digital technology has been widely used in the field of orthodontics in clinical examination, diagnosis, treatment and curative effect evaluation. 3D digital technology greatly improves the accuracy of diagnosis and treatment, and provides effective means for personalized orthodontic treatment. This review focuses on the application of 3D digital technology in the field of orthodontics.

Digital video technology, today and tomorrow

NASA Astrophysics Data System (ADS)

Liberman, J.

1994-10-01

Digital video is probably computing's fastest moving technology today. Just three years ago, the zenith of digital video technology on the PC was the successful marriage of digital text and graphics with analog audio and video by means of expensive analog laser disc players and video overlay boards. The state of the art involves two different approaches to fully digital video on computers: hardware-assisted and software-only solutions.

Records Reaching Recording Data Technologies

NASA Astrophysics Data System (ADS)

Gresik, G. W. L.; Siebe, S.; Drewello, R.

2013-07-01

The goal of RECORDS (Reaching Recording Data Technologies) is the digital capturing of buildings and cultural heritage objects in hard-to-reach areas and the combination of data. It is achieved by using a modified crane from film industry, which is able to carry different measuring systems. The low-vibration measurement should be guaranteed by a gyroscopic controlled advice that has been , developed for the project. The data were achieved by using digital photography, UV-fluorescence photography, infrared reflectography, infrared thermography and shearography. Also a terrestrial 3D laser scanner and a light stripe topography scanner have been used The combination of the recorded data should ensure a complementary analysis of monuments and buildings.

Exposure to Visible Light Emitted from Smartphones and Tablets Increases the Proliferation of Staphylococcus aureus: Can this be Linked to Acne?

PubMed Central

Taheri, M.; Darabyan, M.; Izadbakhsh, E.; Nouri, F.; Haghani, M.; Mortazavi, S.A.R.; Mortazavi, G.; Mortazavi, S.M.J.; Moradi, M.

2017-01-01

Background: Due to rapid advances in modern technologies such as telecommunication technology, the world has witnessed an exponential growth in the use of digital handheld devices (e.g. smartphones and tablets). This drastic growth has resulted in increased global concerns about the safety of these devices. Smartphones, tablets, laptops, and other digital screens emit high levels of short-wavelength visible light (i.e. blue color region in the visible light spectrum). Material and Methods: At a dark environment, Staphylococcus aureus bacteria were exposed to the light emitted from common tablets/smartphones. The control samples were exposed to the same intensity of light generated by a conventional incandescent light bulb. The growth rate of bacteria was examined by measuring the optical density (OD) at 625 nm by using a spectrophotometer before the light exposure and after 30 to 330 minutes of light exposure. Results: The growth rates of bacteria in both smartphone and tablet groups were higher than that of the control group and the maximum smartphone/control and tablet/control growth ratios were observed in samples exposed to digital screens’ light for 300 min (ratios of 3.71 and 3.95, respectively). Conclusion: To the best of our knowledge, this is the first study that investigates the effect of exposure to light emitted from digital screens on the proliferation of Staphylococcus aureus and its association with acne pathogenesis. Our findings show that exposure to short-wavelength visible light emitted from smartphones and tablets can increase the proliferation of Staphylococcus aureus. PMID:28580338

Research of digital controlled DC/DC converter based on STC12C5410AD

NASA Astrophysics Data System (ADS)

Chen, Dan-Jiang; Jin, Xin; Xiao, Zhi-Hong

2010-02-01

In order to study application of digital control technology on DC/DC converter, principle of increment mode PID control algorithm was analyzed in the paper. Then, a SCM named STC12C5410AD was introduced with its internal resources and characteristics. The PID control algorithm can be implemented easily based on it. The output of PID control was used to change the value of a variable that is 255 times than duty cycle, and this reduced the error of calculation. The valid of the presented algorithm was verified by an experiment for a BUCK DC/DC converter. The experimental results indicated that output voltage of the BUCK converter is stable with low ripple.

Digital Actuator Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ken Thomas; Ted Quinn; Jerry Mauck

There are significant developments underway in new types of actuators for power plant active components. Many of these make use of digital technology to provide a wide array of benefits in performance of the actuators and in reduced burden to maintain them. These new product offerings have gained considerable acceptance in use in process plants. In addition, they have been used in conventional power generation very successfully. This technology has been proven to deliver the benefits promised and substantiate the claims of improved performance. The nuclear industry has been reluctant to incorporate digital actuator technology into nuclear plant designs duemore » to concerns due to a number of concerns. These could be summarized as cost, regulatory uncertainty, and a certain comfort factor with legacy analog technology. The replacement opportunity for these types of components represents a decision point for whether to invest in more modern technology that would provide superior operational and maintenance benefits. Yet, the application of digital technology has been problematic for the nuclear industry, due to qualification and regulatory issues. With some notable exceptions, the result has been a continuing reluctance to undertake the risks and uncertainties of implementing digital actuator technology when replacement opportunities present themselves. Rather, utilities would typically prefer to accept the performance limitations of the legacy analog actuator technologies to avoid impacts to project costs and schedules. The purpose of this report is to demonstrate that the benefits of digital actuator technology can be significant in terms of plant performance and that it is worthwhile to address the barriers currently holding back the widespread development and use of this technology. It addresses two important objectives in pursuit of the beneficial use of digital actuator technology for nuclear power plants: 1. To demonstrate the benefits of digital actuator technology over legacy analog sensor technology in both quantitative and qualitative ways. 2. To recognize and address the added difficulty of digital technology qualification, especially in regard to software common cause failure (SCCF), that is introduced by the use of digital actuator technology.« less

40 CFR 451.21 - Effluent limitations attainable by the application of the best practicable control technology...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS... as video cameras, digital scanning sonar, and upweller systems; monitoring of sediment quality...

40 CFR 451.21 - Effluent limitations attainable by the application of the best practicable control technology...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS... as video cameras, digital scanning sonar, and upweller systems; monitoring of sediment quality...

40 CFR 451.21 - Effluent limitations attainable by the application of the best practicable control technology...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS... as video cameras, digital scanning sonar, and upweller systems; monitoring of sediment quality...

Professional Ethics for Digital Age Psychiatry: Boundaries, Privacy, and Communication.

PubMed

Sabin, James E; Harland, Jonathan Clark

2017-09-01

Internet and social media use continue to expand rapidly. Many patients and psychiatrists are bringing digital technologies into the treatment process, but relatively little attention has been paid to the ethical challenges in doing this. This review presents ethical guidelines for psychiatry in the digital age. Surveys demonstrate that patients are eager to make digital technologies part of their treatment. Substantial numbers search for professional and personal information about their therapists. Attitudes among psychiatrists about using digital technologies with patients range from dread to enthusiastic adoption. Digital technologies create four major ethical challenges for psychiatry: managing clinical boundaries; maintaining privacy and confidentiality; establishing realistic expectations regarding digital communications; and upholding professional ideals. Traditional ethical expectations are valid for the evolving digital arena, but guidance must be adapted for actual application in practice.

Can New Digital Technologies Support Parasitology Teaching and Learning?

PubMed

Jabbar, Abdul; Gasser, Robin B; Lodge, Jason

2016-07-01

Traditionally, parasitology courses have mostly been taught face-to-face on campus, but now digital technologies offer opportunities for teaching and learning. Here, we give a perspective on how new technologies might be used through student-centred teaching approaches. First, a snapshot of recent trends in the higher education is provided; then, a brief account is given of how digital technologies [e.g., massive open online courses (MOOCs), flipped classroom (FC), games, quizzes, dedicated Facebook, and digital badges] might promote parasitology teaching and learning in digital learning environments. In our opinion, some of these digital technologies might be useful for competency-based, self-regulated, learner-centred teaching and learning in an online or blended teaching environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

A survey of digital radiography practice in four South African teaching hospitals: an illuminative study.

PubMed

Nyathi, T; Chirwa, Tf; van der Merwe, Dg

2010-01-01

The purpose of this study was to assess radiographer familiarity and preferences with digital radiography in four teaching hospitals and thereafter make recommendations in line with the migration from screen film to digital radiography. A questionnaire was designed to collect data from either qualified or student radiographers from four teaching hospitals. From the four teaching hospitals, there were a total of 205 potential respondents. Among other things, responses regarding experiences and preferences with digital radiography, quality control procedures, patient dose, advantages and disadvantages of digital radiography were sought. The information collected was based on self-reporting by the participants. The study is exploratory in nature and descriptive statistics were generated from the collected data using Microsoft Excel 2007 and StatsDirect software. Sixty-three out of 205 (31%) radiographers from all the four radiology centers responded to the circulated questionnaire. Only 15% (8) of the qualified radiographers had 4 or more years of experience with digital radiography compared to 68% (36) for the same amount of experience with screen-film radiography. Sixty-one percent (38) of the participants had been exposed to digital radiography during their lectures while at university. A small proportion, 16% (10) of the respondents underwent formal training in quality control procedures on the digital X-ray units they were using. Slightly more than half (55%) of the participants felt it was easier for them to retake an image in digital radiography than in screen film radiography. The results of this survey showed that the participants are familiar with digital radiography and have embraced this relatively new technology as shown by the fact that they can identify both its advantages and disadvantages as applied to clinical practice. However, there are minimal quality control procedures specific to digital radiography being undertaken as such there is need for formal education, continuing education and manufacturer training with respect to quality control as institutions make the transition from conventional screen film radiology to digital radiology.

LCoS-SLM technology based on Digital Electro-optics Platform and using in dynamic optics for application development

NASA Astrophysics Data System (ADS)

Tsai, Chun-Wei; Wang, Chen; Lyu, Bo-Han; Chu, Chen-Hsien

2017-08-01

Digital Electro-optics Platform is the main concept of Jasper Display Corp. (JDC) to develop various applications. These applications are based on our X-on-Silicon technologies, for example, X-on-Silicon technologies could be used on Liquid Crystal on Silicon (LCoS), Micro Light-Emitting Diode on Silicon (μLEDoS), Organic Light-Emitting Diode on Silicon (OLEDoS), and Cell on Silicon (CELLoS), etc. LCoS technology is applied to Spatial Light Modulator (SLM), Dynamic Optics, Wavelength Selective Switch (WSS), Holographic Display, Microscopy, Bio-tech, 3D Printing and Adaptive Optics, etc. In addition, μLEDoS technology is applied to Augmented Reality (AR), Head Up Display (HUD), Head-mounted Display (HMD), and Wearable Devices. Liquid Crystal on Silicon - Spatial Light Modulator (LCoSSLM) based on JDC's On-Silicon technology for both amplitude and phase modulation, have an expanding role in several optical areas where light control on a pixel-by-pixel basis is critical for optimum system performance. Combination of the advantage of hardware and software, we can establish a "dynamic optics" for the above applications or more. Moreover, through the software operation, we can control the light more flexible and easily as programmable light processor.

What are the current challenges of managing cancer pain and could digital technologies help?

PubMed

Adam, Rosalind; de Bruin, Marijn; Burton, Christopher David; Bond, Christine M; Giatsi Clausen, Maria; Murchie, Peter

2018-06-01

Pain remains a problem for people with cancer despite effective treatments being available. We aimed to explore current pain management strategies used by patients, caregivers and professionals and to investigate opportunities for digital technologies to enhance cancer pain management. A qualitative study comprising semistructured interviews and focus groups. Patients with cancer pain, their caregivers and health professionals from Northeast Scotland were recruited from a purposive sample of general practices. Professionals were recruited from regional networks. Fifty one participants took part in 33 interviews (eight patients alone, six patient/caregiver dyads and 19 professionals) and two focus groups (12 professionals). Living with cancer was hard work for patients and caregivers and comparable to a 'full-time job'. Patients had personal goals which involved controlling pain intensity and balancing this with analgesic use, side effects, overall symptom burden and social/physical activities.Digital technologies were embraced by most patients, and made living life with advanced cancer easier and richer (eg, video calls with family). Technology was underutilised for pain and symptom management. There were suggestions that technology could support self-monitoring and communicating problems to professionals, but patients and professionals were concerned about technological monitoring adding to the work of managing illness. Cancer pain management takes place in the context of multiple, sometimes competing personal goals. It is possible that technology could be used to help patients share individual symptom experiences and goals, thus enhancing tailored care. The challenge is for digital solutions to add value without adding undue burden. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

[Application of digital earth technology in research of traditional Chinese medicine resources].

PubMed

Liu, Jinxin; Liu, Xinxin; Gao, Lu; Wei, Yingqin; Meng, Fanyun; Wang, Yongyan

2011-02-01

This paper describes the digital earth technology and its core technology-"3S" integration technology. The advance and promotion of the "3S" technology provide more favorable means and technical support for Chinese medicine resources survey, evaluation and appropriate zoning. Grid is a mature and popular technology that can connect all kinds of information resources. The author sums up the application of digital earth technology in the research of traditional Chinese medicine resources in recent years, and proposes the new method and technical route of investigation in traditional Chinese medicine resources, traditional Chinese medicine zoning and suitability assessment by combining the digital earth technology and grid.

Teaching and Learning in the Digital Age

ERIC Educational Resources Information Center

Starkey, Louise

2012-01-01

"Teaching and Learning in the Digital Age" is for all those interested in considering the impact of emerging digital technologies on teaching and learning. It explores the concept of a digital age and perspectives of knowledge, pedagogy and practice within a digital context. By examining teaching with digital technologies through new learning…

Secure, Autonomous, Intelligent Controller for Integrating Distributed Emergency Response Satellite Operations

NASA Astrophysics Data System (ADS)

Ivancic, W. D.; Paulsen, P. E.; Miller, E. M.; Sage, S. P.

This report describes a Secure, Autonomous, and Intelligent Controller for Integrating Distributed Emergency Response Satellite Operations. It includes a description of current improvements to existing Virtual Mission Operations Center technology being used by US Department of Defense and originally developed under NASA funding. The report also highlights a technology demonstration performed in partnership with the United States Geological Service for Earth Resources Observation and Science using DigitalGlobe® satellites to obtain space-based sensor data.

One GHz digitizer for space based laser altimeter

NASA Technical Reports Server (NTRS)

Staples, Edward J.

1991-01-01

This is the final report for the research and development of the one GHz digitizer for space based laser altimeter. A feasibility model was designed, built, and tested. Only partial testing of essential functions of the digitizer was completed. Hybrid technology was incorporated which allows analog storage (memory) of the digitally sampled data. The actual sampling rate is 62.5 MHz, but executed in 16 parallel channels, to provide an effective sampling rate of one GHz. The average power consumption of the one GHz digitizer is not more than 1.5 Watts. A one GHz oscillator is incorporated for timing purposes. This signal is also made available externally for system timing. A software package was also developed for internal use (controls, commands, etc.) and for data communication with the host computer. The digitizer is equipped with an onboard microprocessor for this purpose.

Listening to Communities: Mixed-Method Study of the Engagement of Disadvantaged Mothers and Pregnant Women With Digital Health Technologies

PubMed Central

Broderick, Andrew; Mlo, Hmellisa; Gemmill, Alison; Lindeman, David

2017-01-01

Background US health care providers are increasingly demanding patient engagement with digital health technologies to enroll in care, access personal health information, communicate with providers, and monitor their own health. Such engagement may be difficult for disadvantaged populations who may have limited health literacy, time constraints, or competing priorities. Objective We aimed to understand the extent of adoption and use of digital health tools and to identify key perceived psychological motivators of technology use among disadvantaged first-time pregnant women and mothers of young children. Methods We recruited women from health organizations serving low-income communities in the Midwest and on the East and West coasts. A total of 92 women participated in 14 focus groups. During each session, we administered worksheets that measured 3 utilization outcomes: the number of recent Web-based health-seeking activities, current use of digital health-management practices (eg, accessing personal health information, communicating with providers, and scheduling appointments), and potential adoption of digital health-management tools among low users or nonusers. Responses to the worksheets and to a pre-focus group survey on demographics, technology access, and motivators of use were examined to create user profiles. Separate regression models identified the motivators (eHealth literacy, internal health orientation, and trust in digital information) associated with these outcomes. Qualitative data were incorporated to illustrate the worksheet responses. Results Whereas 97% of the participants reported that they had searched for health information on the Internet in the past year, 42% did not engage in digital health-management practices. Among the low users and nonusers, 49% expressed interest in future adoption of digital health tools. Web-based health information-seeking activities were associated with digital health-management practices (P<.001). When controlling for covariates, eHealth literacy was positively correlated with the number of Web-based health-seeking activities (beta=.03, 95% CI 0.00-0.07). However, an internal health orientation was a much stronger correlate of digital health-management practices (beta=.13, 95% CI 0.02-0.24), whereas trust in digital information increased the odds of potential adoption (vs no adoption) in adjusted models (OR 5.21, 95% CI 0.84-32.53). Demographic characteristics were not important drivers of digital health use and few differences distinguished use among mothers and pregnant women. Conclusions Seeking health information on the Internet may be an important gateway toward engaging in digital health-management practices. Notably, different consumer motivators influence digital health tool use. The relative contributions of each must be explored to design tools and interventions that enhance competencies for the management of self and child health among disadvantaged mothers and pregnant women. Unless we address disparities in digital health tool use, benefits from their use will accrue predominantly to individuals with the resources and skills to use technology effectively. PMID:28679489

Are Digital Natives a Myth or Reality? University Students' Use of Digital Technologies

ERIC Educational Resources Information Center

Margaryan, Anoush; Littlejohn, Allison; Vojt, Gabrielle

2011-01-01

This study investigated the extent and nature of university students' use of digital technologies for learning and socialising. The findings show that students use a limited range of mainly established technologies. Use of collaborative knowledge creation tools, virtual worlds, and social networking sites was low. "Digital natives" and students of…

A Vision for the Net Generation Media Center. Media Matters

ERIC Educational Resources Information Center

Johnson, Doug

2005-01-01

Many children today have never lived in a home without a computer. They are the "Net Generation," constantly "connected" by iPod, cell phone, keyboard, digital video camera, or game controller to various technologies. Recent studies have found that Net Genners see technology as "embedded in society," a primary means of connection with friends, and…

MILCOM '85 - Military Communications Conference, Boston, MA, October 20-23, 1985, Conference Record. Volumes 1, 2, & 3

NASA Astrophysics Data System (ADS)

The present conference on the development status of communications systems in the context of electronic warfare gives attention to topics in spread spectrum code acquisition, digital speech technology, fiber-optics communications, free space optical communications, the networking of HF systems, and applications and evaluation methods for digital speech. Also treated are issues in local area network system design, coding techniques and applications, technology applications for HF systems, receiver technologies, software development status, channel simultion/prediction methods, C3 networking spread spectrum networks, the improvement of communication efficiency and reliability through technical control methods, mobile radio systems, and adaptive antenna arrays. Finally, communications system cost analyses, spread spectrum performance, voice and image coding, switched networks, and microwave GaAs ICs, are considered.

Digital Platforms as Factor Transforming Management Models in Businesses and Industries

NASA Astrophysics Data System (ADS)

Dimitrakiev, D.; Molodchik, A. V.

2018-05-01

Increasingly, digital platforms are built into the value chain, acting as an intermediary between the manufacturer and the consumer. The paper presents tendencies and features of business model transformation in connection with management of the new digital technologies. The limitations of traditional business models and the capabilities of business models based on digital platforms and self-organization were revealed. In the study, the viability of the new business model for the dental industry was confirmed and the new concept of the branch self-organizing control system based on the information platform, blockchain, cryptocurrency and reward of target consumer is offered, including mechanisms that make the model attractive for both the consumer and the service provider.

Flight-testing of the self-repairing flight control system using the F-15 highly integrated digital electronic control flight research facility

NASA Technical Reports Server (NTRS)

Stewart, James F.; Shuck, Thomas L.

1990-01-01

Flight tests conducted with the self-repairing flight control system (SRFCS) installed on the NASA F-15 highly integrated digital electronic control aircraft are described. The development leading to the current SRFCS configuration is highlighted. Key objectives of the program are outlined: (1) to flight-evaluate a control reconfiguration strategy with three types of control surface failure; (2) to evaluate a cockpit display that will inform the pilot of the maneuvering capacity of the damage aircraft; and (3) to flight-evaluate the onboard expert system maintenance diagnostics process using representative faults set to occur only under maneuvering conditions. Preliminary flight results addressing the operation of the overall system, as well as the individual technologies, are included.

HIPAA, dermatology images, and the law.

PubMed

Scheinfeld, Noah; Rothstein, Brooke

2013-12-01

From smart phones to iPads, the world has grown increasingly reliant on new technology. In this ever-expanding digital age, medicine is at the forefront of these new technologies. In the field of dermatology and general medicine, digital images have become an important tool used in patient management. Today, one can even find physicians who use their cellular phone cameras to take patient images and transmit them to other physicians. However, as digital imaging technology has become more prevalent so too have concerns about the impact of this technology on the electronic medical record, quality of patient care, and medicolegal issues. This article will discuss the advent of digital imaging technology in dermatology and the legal ramifications digital images have on medical care, abiding by HIPAA, the use of digital images as evidence, and the possible abuses digital images can pose in a health care setting.

[Impact of digital technology on clinical practices: perspectives from surgery].

PubMed

Zhang, Y; Liu, X J

2016-04-09

Digital medical technologies or computer aided medical procedures, refer to imaging, 3D reconstruction, virtual design, 3D printing, navigation guided surgery and robotic assisted surgery techniques. These techniques are integrated into conventional surgical procedures to create new clinical protocols that are known as "digital surgical techniques". Conventional health care is characterized by subjective experiences, while digital medical technologies bring quantifiable information, transferable data, repeatable methods and predictable outcomes into clinical practices. Being integrated into clinical practice, digital techniques facilitate surgical care by improving outcomes and reducing risks. Digital techniques are becoming increasingly popular in trauma surgery, orthopedics, neurosurgery, plastic and reconstructive surgery, imaging and anatomic sciences. Robotic assisted surgery is also evolving and being applied in general surgery, cardiovascular surgery and orthopedic surgery. Rapid development of digital medical technologies is changing healthcare and clinical practices. It is therefore important for all clinicians to purposefully adapt to these technologies and improve their clinical outcomes.

[Application and prospect of digital technology in the field of orthodontics].

PubMed

Zhou, Y H

2016-06-01

The three-dimensional(3D)digital technology has brought a revolutionary change in diagnostic planning and treatment strategy of orthodontics. Acquisition of 3D image data of the hard and soft tissues of the patients, diagnostic analysis and treatment prediction, and ultimately the individualized orthodontic appliance, will become the development trend and workflow of the 3D orthodontics. With the development of 3D digital technology, the traditional plaster model has been gradually replacing by 3D digital models. Meanwhile, 3D facial soft tissue scan and cone-beam CT scan have been gradually applied to clinical orthodontics, making it possible to get 3D virtual anatomical structure for patients. With the help of digital technology, the diagnostic process is much easier for orthodontist. However how to command the whole digital workflow and put it into practice in the daily work is still a long way to go. The purpose of this article is to enlighten the orthodontists interested in digital technology and discuss the future of digital orthodontics in China.

The x-ray light valve: a potentially low-cost, digital radiographic imaging system-concept and implementation considerations.

PubMed

Webster, Christie Ann; Koprinarov, Ivaylo; Germann, Stephen; Rowlands, J A

2008-03-01

New x-ray radiographic systems based on large-area flat-panel technology have revolutionized our capability to produce digital x-ray images. However, these imagers are extraordinarily expensive compared to the systems they are replacing. Hence, there is a need for a low-cost digital imaging system for general applications in radiology. A novel potentially low-cost radiographic imaging system based on established technologies is proposed-the X-Ray Light Valve (XLV). This is a potentially high-quality digital x-ray detector made of a photoconducting layer and a liquid-crystal cell, physically coupled in a sandwich structure. Upon exposure to x rays, charge is collected on the surface of the photoconductor. This causes a change in the optical properties of the liquid-crystal cell and a visible image is generated. Subsequently, it is digitized by a scanned optical imager. The image formation is based on controlled modulation of light from an external source. The operation and practical implementation of the XLV system are described. The potential performance of the complete system and issues related to sensitivity, spatial resolution, noise, and speed are discussed. The feasibility of clinical use of an XLV device based on amorphous selenium (a-Se) as the photoconductor and a reflective electrically controlled birefringence cell is analyzed. The results of our analysis indicate that the XLV can potentially be adapted to a wide variety of radiographic tasks.

Digital Technology and Student Cognitive Development

ERIC Educational Resources Information Center

Cavanaugh, J. Michael; Giapponi, Catherine C.; Golden, Timothy D.

2016-01-01

Digital technology has proven a beguiling, some even venture addictive, presence in the lives of our 21st century (millennial) students. And while screen technology may offer select cognitive benefits, there is mounting evidence in the cognitive neuroscience literature that digital technology is restructuring the way our students read and think,…

Using Information and Communication Technology (ICT) to the Maximum: Learning and Teaching Biology with Limited Digital Technologies

ERIC Educational Resources Information Center

Van Rooy, Wilhelmina S.

2012-01-01

Background: The ubiquity, availability and exponential growth of digital information and communication technology (ICT) creates unique opportunities for learning and teaching in the senior secondary school biology curriculum. Digital technologies make it possible for emerging disciplinary knowledge and understanding of biological processes…

Down syndrome in diverse populations.

PubMed

Kruszka, Paul; Porras, Antonio R; Sobering, Andrew K; Ikolo, Felicia A; La Qua, Samantha; Shotelersuk, Vorasuk; Chung, Brian H Y; Mok, Gary T K; Uwineza, Annette; Mutesa, Leon; Moresco, Angélica; Obregon, María Gabriela; Sokunbi, Ogochukwu Jidechukwu; Kalu, Nnenna; Joseph, Daniel Akinsanya; Ikebudu, Desmond; Ugwu, Christopher Emeka; Okoromah, Christy A N; Addissie, Yonit A; Pardo, Katherine L; Brough, J Joseph; Lee, Ni-Chung; Girisha, Katta M; Patil, Siddaramappa Jagdish; Ng, Ivy S L; Min, Breana Cham Wen; Jamuar, Saumya S; Tibrewal, Shailja; Wallang, Batriti; Ganesh, Suma; Sirisena, Nirmala D; Dissanayake, Vajira H W; Paththinige, C Sampath; Prabodha, L B Lahiru; Richieri-Costa, Antonio; Muthukumarasamy, Premala; Thong, Meow-Keong; Jones, Kelly L; Abdul-Rahman, Omar A; Ekure, Ekanem Nsikak; Adeyemo, Adebowale A; Summar, Marshall; Linguraru, Marius George; Muenke, Maximilian

2017-01-01

Down syndrome is the most common cause of cognitive impairment and presents clinically with universally recognizable signs and symptoms. In this study, we focus on exam findings and digital facial analysis technology in individuals with Down syndrome in diverse populations. Photos and clinical information were collected on 65 individuals from 13 countries, 56.9% were male and the average age was 6.6 years (range 1 month to 26 years; SD = 6.6 years). Subjective findings showed that clinical features were different across ethnicities (Africans, Asians, and Latin Americans), including brachycephaly, ear anomalies, clinodactyly, sandal gap, and abundant neck skin, which were all significantly less frequent in Africans (P < 0.001, P < 0.001, P < 0.001, P < 0.05, and P < 0.05, respectively). Evaluation using a digital facial analysis technology of a larger diverse cohort of newborns to adults (n = 129 cases; n = 132 controls) was able to diagnose Down syndrome with a sensitivity of 0.961, specificity of 0.924, and accuracy of 0.943. Only the angles at medial canthus and ala of the nose were common significant findings amongst different ethnicities (Caucasians, Africans, and Asians) when compared to ethnically matched controls. The Asian group had the least number of significant digital facial biometrics at 4, compared to Caucasians at 8 and Africans at 7. In conclusion, this study displays the wide variety of findings across different geographic populations in Down syndrome and demonstrates the accuracy and promise of digital facial analysis technology in the diagnosis of Down syndrome internationally. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Two innovative healthcare technologies at the intersection of serious games, alternative realities, and play therapy.

PubMed

Brahnam, Sheryl; Brooks, Anthony L

2014-01-01

Using game technologies and digital media for improving physical and mental health and for the therapeutic benefit and well-being of a wide range of people is an area of study that is rapidly expanding. Much research in this emerging field is centered at the intersection of serious games, alternative realities, and play therapy. In this paper the authors describe their transdisciplinary work at this intersection: i) an integrative system of psychotherapy technologies called MyPsySpace currently being prototyped in Second Life with the aim of offering new and virtual translations of traditional expressive therapies (virtual sandplay, virtual drama therapy, digital expressive therapy, and virtual safe spaces) and ii) a mature body of research entitled SoundScapes that is exploring the use of interactive video games and abstract creative expression (making music, digital painting, and robotic device control) as a supplement to traditional physical rehabilitation intervention. Aside from introducing our work to a broader audience, our goal is to encourage peers to investigate ideas that reach across disciplines-to both risk and reap the benefits of combining technologies, theories, and methods stemming from multiple disciplines.

Digital technologies and chronic disease management.

PubMed

Georgeff, Michael

2014-12-01

Digital technologies will become a major part of our healthcare system, with particular impact in primary care. However, many healthcare professionals are not sufficiently informed of the digital technologies available today and how they and their patients can gain substantial benefit from adoption of these technologies. To raise awareness of the potential benefits of using digital technologies for improving practice efficiencies and patient health outcomes. Implementing best practice care for patients with chronic and complex conditions is one of the greatest challenges facing general practice and other primary care providers. It has been suggested that digital technologies could assist by decreasing the administrative burden of care delivery, improving quality of care, increasing practice efficiencies and better supporting patient self-management. In this paper, we consider some areas in the management of chronic and long-term conditions where digital and mobile health solutions can make a difference today.

WTEC monograph on instrumentation, control and safety systems of Canadian nuclear facilities

NASA Technical Reports Server (NTRS)

Uhrig, Robert E.; Carter, Richard J.

1993-01-01

This report updates a 1989-90 survey of advanced instrumentation and controls (I&C) technologies and associated human factors issues in the U.S. and Canadian nuclear industries carried out by a team from Oak Ridge National Laboratory (Carter and Uhrig 1990). The authors found that the most advanced I&C systems are in the Canadian CANDU plants, where the newest plant (Darlington) has digital systems in almost 100 percent of its control systems and in over 70 percent of its plant protection system. Increased emphasis on human factors and cognitive science in modern control rooms has resulted in a reduced workload for the operators and the elimination of many human errors. Automation implemented through digital instrumentation and control is effectively changing the role of the operator to that of a systems manager. The hypothesis that properly introducing digital systems increases safety is supported by the Canadian experience. The performance of these digital systems has been achieved using appropriate quality assurance programs for both hardware and software development. Recent regulatory authority review of the development of safety-critical software has resulted in the creation of isolated software modules with well defined interfaces and more formal structure in the software generation. The ability of digital systems to detect impending failures and initiate a fail-safe action is a significant safety issue that should be of special interest to nuclear utilities and regulatory authorities around the world.

Aircraft digital flight control technical review

NASA Technical Reports Server (NTRS)

Davenport, Otha B.; Leggett, David B.

1993-01-01

The Aircraft Digital Flight Control Technical Review was initiated by two pilot induced oscillation (PIO) incidents in the spring and summer of 1992. Maj. Gen. Franklin (PEO) wondered why the Air Force development process for digital flight control systems was not preventing PIO problems. Consequently, a technical review team was formed to examine the development process and determine why PIO problems continued to occur. The team was also to identify the 'best practices' used in the various programs. The charter of the team was to focus on the PIO problem, assess the current development process, and document the 'best practices.' The team reviewed all major USAF aircraft programs with digital flight controls, specifically, the F-15E, F-16C/D, F-22, F-111, C-17, and B-2. The team interviewed contractor, System Program Office (SPO), and Combined Test Force (CTF) personnel on these programs. The team also went to NAS Patuxent River to interview USN personnel about the F/A-18 program. The team also reviewed experimental USAF and NASA systems with digital flight control systems: X-29, X-31, F-15 STOL and Maneuver Technology Demonstrator (SMTD), and the Variable In-Flight Stability Test Aircraft (VISTA). The team also discussed the problem with other experts in the field including Ralph Smith and personnel from Calspan. The major conclusions and recommendations from the review are presented.

Digital imagery/telecytology. International Academy of Cytology Task Force summary. Diagnostic Cytology Towards the 21st Century: An International Expert Conference and Tutorial.

PubMed

O'Brien, M J; Takahashi, M; Brugal, G; Christen, H; Gahm, T; Goodell, R M; Karakitsos, P; Knesel, E A; Kobler, T; Kyrkou, K A; Labbe, S; Long, E L; Mango, L J; McGoogan, E; Oberholzer, M; Reith, A; Winkler, C

1998-01-01

Optical digital imaging and its related technologies have applications in cytopathology that encompass training and education, image analysis, diagnosis, report documentation and archiving, and telecommunications. Telecytology involves the use of telecommunications to transmit cytology images for the purposes of diagnosis, consultation or education. This working paper provides a mainly informational overview of optical digital imaging and summarizes current technologic resources and applications and some of the ethical and legal implications of the use of these new technologies in cytopathology. Computer hardware standards for optical digital imagery will continue to be driven mainly by commercial interests and nonmedical imperatives, but professional organizations can play a valuable role in developing recommendations or standards for digital image sampling, documentation, archiving, authenticity safeguards and teleconsultation protocols; in addressing patient confidentiality and ethical, legal and informed consent issues; and in providing support for quality assurance and standardization of digital image-based testing. There is some evidence that high levels of accuracy for telepathology diagnosis can be achieved using existing dynamic systems, which may also be applicable to telecytology consultation. Static systems for both telepathology and telecytology, which have the advantage of considerably lower cost, appear to have lower levels of accuracy. Laboratories that maintain digital image databases should adopt practices and protocols that ensure patient confidentiality. Individuals participating in telecommunication of digital images for diagnosis should be properly qualified, meet licensing requirements and use procedures that protect patient confidentiality. Such individuals should be cognizant of the limitations of the technology and employ quality assurance practices that ensure the validity and accuracy of each consultation. Even in an informal teleconsultation setting one should define the extent of participation and be mindful of potential malpractice liability. Digital imagery applications will continue to present new opportunities and challenges. Position papers such as this are directed toward assisting the profession to stay informed and in control of these applications in the laboratory. Telecytology is an area in particular need of studies of good quality to provide data on factors affecting accuracy. New technologic approaches to addressing the issue of selective sampling in static image consultation are needed. The use of artificial intelligence software as an adjunct to enhance the accuracy and reproducibility of cytologic diagnosis of digital images in routine and consultation settings deserves to be pursued. Other telecytology-related issues that require clarification and the adoption of workable guidelines include interstate licensure and protocols to define malpractice liability.

Hybrid Placemaking in the Library: Designing Digital Technology to Enhance Users' On-Site Experience

ERIC Educational Resources Information Center

Bilandzic, Mark; Johnson, Daniel

2013-01-01

This paper presents research findings and design strategies that illustrate how digital technology can be applied as a tool for "hybrid" placemaking in ways that would not be possible in purely digital or physical spaces. Digital technology has revolutionised the way people learn and gather new information. This trend has challenged the…

Integration of Digital Technologies into Play-Based Pedagogy in Kuwaiti Early Childhood Education: Teachers' Views, Attitudes and Aptitudes

ERIC Educational Resources Information Center

Aldhafeeri, Fayiz; Palaiologou, Ioanna; Folorunsho, Aderonke

2016-01-01

Scholars in the field of early childhood education are still debating the inclusion of digital technologies in play-based pedagogy and our understanding of digital play in early childhood education is still developing. This research paper examines early childhood education teachers' views, aptitudes and attitudes towards digital technologies in…

The Role and Value of Public Libraries in the Age of Digital Technologies

ERIC Educational Resources Information Center

Aabo, Svanhild

2005-01-01

Discusses public libraries' role and value in the age of digital technologies. Reassessments of their role due to technological development and widespread public use of the Internet are analysed. Central challenges of the digital society, including an increased digital divide and a weakening of local community identity, have resulted in lower…

Digital Leisure-Time Activities, Cognition, Learning Behaviour and Information Literacy: What Are Our Children Learning?

ERIC Educational Resources Information Center

Grimley, Mick

2012-01-01

Recent developments in digital technology have resulted in the unprecedented uptake of digital technology engagement as a leisure-time pursuit across the age span. This has resulted in the speculation that such use of digital technology is responsible for changes in cognition and learning behaviour. This study investigated two groups of…

The pressure control technology of the active stressed lap

NASA Astrophysics Data System (ADS)

Li, Ying; Wang, Daxing

2010-10-01

The active stressed lap polishing technology is a kind of new polishing technology that can actively deform the lap surface to become an off-axis asphere according to different lap position on mirror surface and different angle of lap. The pressure of the lap on the mirror is an important factor affecting the grinding efficiency of the optics mirror. The active stressed lap technology using dynamic pressure control solution in the process of polishing astronomical Aspheric Mirror with faster asphericity will provide the advantage like high polishing speed and natural smooth, etc. This article puts emphases on the pressure control technology of the active stressed lap technology. It requires that the active stressed lap keeps symmetrical vertical compression on the mirrors in the process of grinding mirrors. With a background of an active stressed lap 450mm in diameter, this article gives an outline of the pressure control organization, analyzes the principle of pressure control and proposes the limitations of the present pressure control organization and the relevant solutions, designs a digital pressure controller with C32-bit RISC embedded and gives the relevant experimental test result finally.

Advanced Military Pay System Concepts. Evaluation of Opportunities through Information Technology.

DTIC Science & Technology

1980-07-01

trans- mdtter (UART) to interface with a modem . The main processor was then responsible for input and output between main memory and the UART...digital, "run-length" encoding scheme which is very effective in reducing the amount of data to be transmitted. Machines of this type include a modem ...Output control as well as data compression will be combined with appropriate modems or interfaces to digital transmission channels and microprocessor

Can We Teach Digital Natives Digital Literacy?

ERIC Educational Resources Information Center

Ng, Wan

2012-01-01

In recent years, there has been much debate about the concept of digital natives, in particular the differences between the digital natives' knowledge and adoption of digital technologies in informal versus formal educational contexts. This paper investigates the knowledge about educational technologies of a group of undergraduate students…

Basis for the implementation of digital signature in Argentine's health environment

NASA Astrophysics Data System (ADS)

Escobar, P. P.; Formica, M.

2007-11-01

The growth of telemedical applications and electronic transactions in health environments is paced by the constant technology evolution. This implies a big cultural change in traditional medicine and in hospital information systems' users which arrival is delayed, basically, by the lack of solid laws and a well defined role-based infrastructure. The use of digital signature as a mean of identification, authentication, confidentiality and non-repudiation is the most suitable tool for assuring the electronic transactions and patient's data protection. The implementation of a Public Key Infrastructure (PKI) in health environment allows for authentication, encryption and use of digital signature for assuring confidentiality and control of the movement of sensitive information. This work defines the minimum technological, legal and procedural basis for a successful PKI implementation and establishes the roles for the different actors in the chain of confidence in the public health environment of Argentine.

Digitalization and the global technology trends

NASA Astrophysics Data System (ADS)

Ignat, V.

2017-08-01

Digitalization, connected products and services, and shortening innovation cycles are widely discussed topics in management practice and theory and demand for new concepts. We analysed how companies innovated their business models and how are the new the technology trends. We found out, that have a positive approach to digitalization but the technology strategy still runs its original business model. Digitalization forces to new solution orientation. For companies it is necessary to master the digital transformation, new innovations have to be developed. Furthermore, digitalization / Industry 4.0 linking the real-life factory with virtual reality, will play an increasingly important role in global manufacturing. Companies have to obtain new digital capabilities, in order to make their company sustainable for the future. A long term growth and welfare in Europe could be guaranteed only by new technology innovation.

Integrated controls for a new aircraft generation

NASA Technical Reports Server (NTRS)

Mace, W. D.; Howell, W. E.

1978-01-01

Many of the commercial aircraft now flying will have to be phased out in the early 1980s because of fuel inefficiency and unacceptable noise levels. This paper discusses the role of new digital technology in making aircraft more fuel efficient, more reliable, and quieter. Attention is given to the integration of sensing and control functions in an aircraft in order to provide a simple, lightweight, and high-redundancy system. Technology under development now is expected to come on-line in the 1990s.

Secure, Autonomous, Intelligent Controller for Integrating Distributed Emergency Response Satellite Operations

NASA Technical Reports Server (NTRS)

Ivancic, William D.; Paulsen, Phillip E.; Miller, Eric M.; Sage, Steen P.

2013-01-01

This report describes a Secure, Autonomous, and Intelligent Controller for Integrating Distributed Emergency Response Satellite Operations. It includes a description of current improvements to existing Virtual Mission Operations Center technology being used by US Department of Defense and originally developed under NASA funding. The report also highlights a technology demonstration performed in partnership with the United States Geological Service for Earth Resources Observation and Science using DigitalGlobe(Registered TradeMark) satellites to obtain space-based sensor data.

Controller Evaluation of Initial Data Link En Route Air Traffic Control Services: ISSS Design Development. Study 1

DTIC Science & Technology

1994-05-01

services developed for transmission using Data Link technology . Candidate designs for five ATC services and functions for the new Initial Sector Suite System...clarify suspected confusions to avoid further congestion. 1.2.2 Data Link Communications . Data Link is a digital communications technology which is being... developed as a supplement to traditional voice radio for two-way, air-ground ATC communications and other applications. As shown in figure 1, Data Link

Differentiating Digital Writing Instruction: The Intersection of Technology, Writing Instruction, and Digital Genre Knowledge

ERIC Educational Resources Information Center

Martin, Nicole M.; Lambert, Claire

2015-01-01

U.S. adolescents' prior technology experiences and exposure to digital genres vary, but they will often write digital texts as they enter college and adulthood. We explored middle school students' digital writing instructional experience in the context of a university-based summer digital writing camp. The sixth- through eighth-grade adolescents…

Digital security technology simplified.

PubMed

Scaglione, Bernard J

2007-01-01

Digital security technology is making great strides in replacing analog and other traditional security systems including CCTV card access, personal identification and alarm monitoring applications. Like any new technology, the author says, it is important to understand its benefits and limitations before purchasing and installing, to ensure its proper operation and effectiveness. This article is a primer for security directors on how digital technology works. It provides an understanding of the key components which make up the foundation for digital security systems, focusing on three key aspects of the digital security world: the security network, IP cameras and IP recorders.

Malaysian Teachers' Conceptions and Uses of Digital Technology in English Writing Instruction: A Multiple Case Study

ERIC Educational Resources Information Center

Mohamed Razali, Abu Bakar

2013-01-01

Very little is known about how teachers' "conceptualizations" of digital technology and their "uses" of the technology evolve and relate. Yet knowing about and understanding teachers' conceptions and uses of digital technology are essential for learning how teachers integrate it effectively for student learning. By applying…

A Historical Perspective on Student Affairs Professionals' Use of Digital Technology

ERIC Educational Resources Information Center

Cabellon, Edmund T.; Payne-Kirchmeier, Julie

2016-01-01

This chapter provides a historical perspective of student affairs professionals' use of digital and social technologies in their work on college campuses. The purpose of the chapter is to describe how digital technology tools have evolved since 2005, demonstrate how student affairs technology shifted and changed during this time, and shape student…

Technological Implications for Assessment Ecosystems: Opportunities for Digital Technology to Advance Assessment

ERIC Educational Resources Information Center

Behrens, John T.; DiCerbo, Kristen E.

2014-01-01

Background: It would be easy to think the technological shifts in the digital revolution are simple incremental progressions in societal advancement. However, the nature of digital technology is resulting in qualitative differences in nearly all parts of daily life. Purpose: This paper investigates how the new possibilities for understanding,…

Summary of: dental practitioners and a digital future: an initial exploration of barriers and incentives to adopting digital technologies.

PubMed

Addy, Liam

2013-12-01

Digital technologies are proliferating into dental practices. While their technical attributes have often been studied, it remains unclear why some dentists adopt and use these technologies more than others. AIM To explore the incentives for and barriers against accepting and using digital dental technologies. Eleven semi-structured qualitative interviews were conducted with experts in dentistry, dental technology and dental education in the Netherlands. Dentists' acceptance and use of digital technologies are to varying degrees driven by the perceived advantages over analogue methods, perceived influence on treatment quality, dentists' personal and professional orientation, and social influence from peers and external groups. These effects are complemented by personal and dental-practice characteristics. The findings suggest that there are large differences in motivation to adopt and use digital technologies between early adopters, late adopters and non-adopters, which should be examined in greater detail. We recommend that educators, dentists, and representatives of the dental industry who deal with the diffusion of these technologies take account of dentists' widely different attitudes to digitalisation.

[Overall digitalization: leading innovation of endodontics in big data era].

PubMed

Ling, J Q

2016-04-09

In big data era, digital technologies bring great challenges and opportunities to modern stomatology. The applications of digital technologies, such as cone-beam CT(CBCT), computer aided design,(CAD)and computer aided manufacture(CAM), 3D printing and digital approaches for education , provide new concepts and patterns to the treatment and study of endodontic diseases. This review provides an overview of the application and prospect of commonly used digital technologies in the development of endodontics.

A digital optical phase-locked loop for diode lasers based on field programmable gate array

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu Zhouxiang; Zhang Xian; Huang Kaikai

2012-09-15

We have designed and implemented a highly digital optical phase-locked loop (OPLL) for diode lasers in atom interferometry. The three parts of controlling circuit in this OPLL, including phase and frequency detector (PFD), loop filter and proportional integral derivative (PID) controller, are implemented in a single field programmable gate array chip. A structure type compatible with the model MAX9382/MCH12140 is chosen for PFD and pipeline and parallelism technology have been adapted in PID controller. Especially, high speed clock and twisted ring counter have been integrated in the most crucial part, the loop filter. This OPLL has the narrow beat notemore » line width below 1 Hz, residual mean-square phase error of 0.14 rad{sup 2} and transition time of 100 {mu}s under 10 MHz frequency step. A main innovation of this design is the completely digitalization of the whole controlling circuit in OPLL for diode lasers.« less

Aeroservoelastic wind-tunnel investigations using the Active Flexible Wing Model: Status and recent accomplishments

NASA Technical Reports Server (NTRS)

Noll, Thomas E.; Perry, Boyd, III; Tiffany, Sherwood H.; Cole, Stanley R.; Buttrill, Carey S.; Adams, William M., Jr.; Houck, Jacob A.; Srinathkumar, S.; Mukhopadhyay, Vivek; Pototzky, Anthony S.

1989-01-01

The status of the joint NASA/Rockwell Active Flexible Wing Wind-Tunnel Test Program is described. The objectives are to develop and validate the analysis, design, and test methodologies required to apply multifunction active control technology for improving aircraft performance and stability. Major tasks include designing digital multi-input/multi-output flutter-suppression and rolling-maneuver-load alleviation concepts for a flexible full-span wind-tunnel model, obtaining an experimental data base for the basic model and each control concept and providing comparisons between experimental and analytical results to validate the methodologies. The opportunity is provided to improve real-time simulation techniques and to gain practical experience with digital control law implementation procedures.

The effectiveness of annotated (vs. non-annotated) digital pathology slides as a teaching tool during dermatology and pathology residencies.

PubMed

Marsch, Amanda F; Espiritu, Baltazar; Groth, John; Hutchens, Kelli A

2014-06-01

With today's technology, paraffin-embedded, hematoxylin & eosin-stained pathology slides can be scanned to generate high quality virtual slides. Using proprietary software, digital images can also be annotated with arrows, circles and boxes to highlight certain diagnostic features. Previous studies assessing digital microscopy as a teaching tool did not involve the annotation of digital images. The objective of this study was to compare the effectiveness of annotated digital pathology slides versus non-annotated digital pathology slides as a teaching tool during dermatology and pathology residencies. A study group composed of 31 dermatology and pathology residents was asked to complete an online pre-quiz consisting of 20 multiple choice style questions, each associated with a static digital pathology image. After completion, participants were given access to an online tutorial composed of digitally annotated pathology slides and subsequently asked to complete a post-quiz. A control group of 12 residents completed a non-annotated version of the tutorial. Nearly all participants in the study group improved their quiz score, with an average improvement of 17%, versus only 3% (P = 0.005) in the control group. These results support the notion that annotated digital pathology slides are superior to non-annotated slides for the purpose of resident education. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Real-time Simulation of Turboprop Engine Control System

NASA Astrophysics Data System (ADS)

Sheng, Hanlin; Zhang, Tianhong; Zhang, Yi

2017-05-01

On account of the complexity of turboprop engine control system, real-time simulation is the technology, under the prerequisite of maintaining real-time, to effectively reduce development cost, shorten development cycle and avert testing risks. The paper takes RT-LAB as a platform and studies the real-time digital simulation of turboprop engine control system. The architecture, work principles and external interfaces of RT-LAB real-time simulation platform are introduced firstly. Then based on a turboprop engine model, the control laws of propeller control loop and fuel control loop are studied. From that and on the basis of Matlab/Simulink, an integrated controller is designed which can realize the entire process control of the engine from start-up to maximum power till stop. At the end, on the basis of RT-LAB platform, the real-time digital simulation of the designed control system is studied, different regulating plans are tried and more ideal control effects have been obtained.

Applying the Technology Acceptance Model in a Study of the Factors Affecting Usage of the Taiwan Digital Archives System

ERIC Educational Resources Information Center

Hong, Jon-Chao; Hwang, Ming-Yueh; Hsu, Hsuan-Fang; Wong, Wan-Tzu; Chen, Mei-Yung

2011-01-01

The rapid development of information and communication technology and the popularization of the Internet have given a boost to digitization technologies. Since 2001, The National Science Council (NSC) of Taiwan has invested a large amount of funding in the National Digital Archives Program (NDAP) to develop digital content. Some studies have…

Deconstructing Digital Natives: Young People, Technology, and the New Literacies

ERIC Educational Resources Information Center

Thomas, Michael, Ed.

2011-01-01

There have been many attempts to define the generation of students who emerged with the Web and new digital technologies in the early 1990s. The term "digital native" refers to the generation born after 1980, which has grown up in a world where digital technologies and the internet are a normal part of everyday life. Young people…

Digital Technology Use by the Students and English Teachers and Self-Directed Language Learning

ERIC Educational Resources Information Center

Sert, Nehir; Boynuegri, Ebru

2017-01-01

The digital era is a new challenge for teachers. While children get acquainted with the digital technology before the age of six, teachers, who have encountered with the digital world at a later time in their lives, struggle with it. Self-directed learning, which is crucial for lifelong learning, can be enhanced by the use technology particularly…

Using Digital Comics to Develop Digital Literacy: Fostering Functionally, Critically, and Rhetorically Literate Students

ERIC Educational Resources Information Center

Kirchoff, Jeff

2017-01-01

Literacy scholarship has established the importance of teaching, supporting, and facilitating digital literacy education for 21st century students. Stuart Selber goes a step further, arguing that students must be functionally (using digital technology), critically (questioning digital technology), and rhetorically (producing effective digital…

E-Learning Environments for Digitally-Minded Students

ERIC Educational Resources Information Center

Andone, Diana; Dron, Jon; Pemberton, Lyn; Boyne, Chris

2007-01-01

While most existing online learning environments cater for needs identified during the 1990s, a new generation of digital students has emerged in the developed world. Digital students are young adults who have grown up with digital technologies integrated as an everyday feature of their lives. Digital students use technology differently, fluidly…

From protection of privacy to control of data streams: a focus group study on biobanks in the information society.

PubMed

Snell, K; Starkbaum, J; Lauß, G; Vermeer, A; Helén, I

2012-01-01

Most people in Europe do not know what biobanks are. In this study, public perceptions of biobanks and collection of genetic and health data were analyzed in relation to other technologies and digital networks where personal information is compiled and distributed. In this setting, people contextualized biobanks in line with their daily experiences with other technologies and data streams. The analysis was based on 18 focus group discussions conducted in Austria, Finland and Germany. We examined the ways in which people frame and talk about problems and benefits of information distribution in digital networks and biobanks. People identify many challenges associated with collection of personal data in the information society. The study showed that instead of privacy - which has been the key term of bioethical debates on biobanks - the notions of control and controllability are most essential for people. From the viewpoint of biobanks, issues of controllability pose challenges. In the information society, people have become accustomed to controlling personal data, which is particularly difficult in relation to biobanks. They expressed strong concerns over the controllability of the goals and benefits of biobanks. Copyright © 2012 S. Karger AG, Basel.

Wireless Control of Smartphones with Tongue Motion Using Tongue Drive Assistive Technology

PubMed Central

Kim, Jeonghee; Huo, Xueliang

2010-01-01

Tongue Drive System (TDS) is a noninvasive, wireless and wearable assistive technology that helps people with severe disabilities control their environments using their tongue motion. TDS translates specific tongue gestures to commands by detecting a small permanent magnetic tracer on the users’ tongue. We have linked the TDS to a smartphone (iPhone/iPod Touch) with a customized wireless module, added to the iPhone. We also migrated and ran the TDS sensor signal processing algorithm and graphical user interface on the iPhone in real time. The TDS-iPhone interface was evaluated by four able-bodied subjects for dialing 10-digit phone numbers using the standard telephone keypad and three methods of prompting the numbers: visual, auditory, and cognitive. Preliminary results showed that the interface worked quite reliably at a rate of 15.4 digits per minute, on average, with negligible errors. PMID:21096049

Digital microfluidics: A promising technique for biochemical applications

NASA Astrophysics Data System (ADS)

Wang, He; Chen, Liguo; Sun, Lining

2017-12-01

Digital microfluidics (DMF) is a versatile microfluidics technology that has significant application potential in the areas of automation and miniaturization. In DMF, discrete droplets containing samples and reagents are controlled to implement a series of operations via electrowetting-on-dielectric. This process works by applying electrical potentials to an array of electrodes coated with a hydrophobic dielectric layer. Unlike microchannels, DMF facilitates precise control over multiple reaction processes without using complex pump, microvalve, and tubing networks. DMF also presents other distinct features, such as portability, less sample consumption, shorter chemical reaction time, flexibility, and easier combination with other technology types. Due to its unique advantages, DMF has been applied to a broad range of fields (e.g., chemistry, biology, medicine, and environment). This study reviews the basic principles of droplet actuation, configuration design, and fabrication of the DMF device, as well as discusses the latest progress in DMF from the biochemistry perspective.

CMOS Image Sensors: Electronic Camera On A Chip

NASA Technical Reports Server (NTRS)

Fossum, E. R.

1995-01-01

Recent advancements in CMOS image sensor technology are reviewed, including both passive pixel sensors and active pixel sensors. On- chip analog to digital converters and on-chip timing and control circuits permit realization of an electronic camera-on-a-chip. Highly miniaturized imaging systems based on CMOS image sensor technology are emerging as a competitor to charge-coupled devices for low cost uses.

Digital Interface Board to Control Phase and Amplitude of Four Channels

NASA Technical Reports Server (NTRS)

Smith, Amy E.; Cook, Brian M.; Khan, Abdur R.; Lux, James P.

2011-01-01

An increasing number of parts are designed with digital control interfaces, including phase shifters and variable attenuators. When designing an antenna array in which each antenna has independent amplitude and phase control, the number of digital control lines that must be set simultaneously can grow very large. Use of a parallel interface would require separate line drivers, more parts, and thus additional failure points. A convenient form of control where single-phase shifters or attenuators could be set or the whole set could be programmed with an update rate of 100 Hz is needed to solve this problem. A digital interface board with a field-programmable gate array (FPGA) can simultaneously control an essentially arbitrary number of digital control lines with a serial command interface requiring only three wires. A small set of short, high-level commands provides a simple programming interface for an external controller. Parity bits are used to validate the control commands. Output timing is controlled within the FPGA to allow for rapid update rates of the phase shifters and attenuators. This technology has been used to set and monitor eight 5-bit control signals via a serial UART (universal asynchronous receiver/transmitter) interface. The digital interface board controls the phase and amplitude of the signals for each element in the array. A host computer running Agilent VEE sends commands via serial UART connection to a Xilinx VirtexII FPGA. The commands are decoded, and either outputs are set or telemetry data is sent back to the host computer describing the status and the current phase and amplitude settings. This technology is an integral part of a closed-loop system in which the angle of arrival of an X-band uplink signal is detected and the appropriate phase shifts are applied to the Ka-band downlink signal to electronically steer the array back in the direction of the uplink signal. It will also be used in the non-beam-steering case to compensate for phase shift variations through power amplifiers. The digital interface board can be used to set four 5-bit phase shifters and four 5-bit attenuators and monitor their current settings. Additionally, it is useful outside of the closed-loop system for beamsteering alone. When the VEE program is started, it prompts the user to initialize variables (to zero) or skip initialization. After that, the program enters into a continuous loop waiting for the telemetry period to elapse or a button to be pushed. A telemetry request is sent when the telemetry period is elapsed (every five seconds). Pushing one of the set or reset buttons will send the appropriate command. When a command is sent, the interface status is returned, and the user will be notified by a pop-up window if any error has occurred. The program runs until the End Program button is depressed.

Traffic Monitor

NASA Technical Reports Server (NTRS)

1995-01-01

Intelligent Vision Systems, Inc. (InVision) needed image acquisition technology that was reliable in bad weather for its TDS-200 Traffic Detection System. InVision researchers used information from NASA Tech Briefs and assistance from Johnson Space Center to finish the system. The NASA technology used was developed for Earth-observing imaging satellites: charge coupled devices, in which silicon chips convert light directly into electronic or digital images. The TDS-200 consists of sensors mounted above traffic on poles or span wires, enabling two sensors to view an intersection; a "swing and sway" feature to compensate for movement of the sensors; a combination of electronic shutter and gain control; and sensor output to an image digital signal processor, still frame video and optionally live video.

Technological innovations in mental healthcare: harnessing the digital revolution.

PubMed

Hollis, Chris; Morriss, Richard; Martin, Jennifer; Amani, Sarah; Cotton, Rebecca; Denis, Mike; Lewis, Shôn

2015-04-01

Digital technology has the potential to transform mental healthcare by connecting patients, services and health data in new ways. Digital online and mobile applications can offer patients greater access to information and services and enhance clinical management and early intervention through access to real-time patient data. However, substantial gaps exist in the evidence base underlying these technologies. Greater patient and clinician involvement is needed to evaluate digital technologies and ensure they target unmet needs, maintain public trust and improve clinical outcomes. Royal College of Psychiatrists.

Application of digital computer APU modeling techniques to control system design.

NASA Technical Reports Server (NTRS)

Bailey, D. A.; Burriss, W. L.

1973-01-01

Study of the required controls for a H2-O2 auxiliary power unit (APU) technology program for the Space Shuttle. A steady-state system digital computer program was prepared and used to optimize initial system design. Analytical models of each system component were included. The program was used to solve a nineteen-dimensional problem, and then time-dependent differential equations were added to the computer program to simulate transient APU system and control. Some system parameters were considered quasi-steady-state, and others were treated as differential variables. The dynamic control analysis proceeded from initial ideal control modeling (which considered one control function and assumed the others to be ideal), stepwise through the system (adding control functions), until all of the control functions and their interactions were considered. In this way, the adequacy of the final control design over the required wide range of APU operating conditions was established.

Periodic reference tracking control approach for smart material actuators with complex hysteretic characteristics

NASA Astrophysics Data System (ADS)

Sun, Zhiyong; Hao, Lina; Song, Bo; Yang, Ruiguo; Cao, Ruimin; Cheng, Yu

2016-10-01

Micro/nano positioning technologies have been attractive for decades for their various applications in both industrial and scientific fields. The actuators employed in these technologies are typically smart material actuators, which possess inherent hysteresis that may cause systems behave unexpectedly. Periodic reference tracking capability is fundamental for apparatuses such as scanning probe microscope, which employs smart material actuators to generate periodic scanning motion. However, traditional controller such as PID method cannot guarantee accurate fast periodic scanning motion. To tackle this problem and to conduct practical implementation in digital devices, this paper proposes a novel control method named discrete extended unparallel Prandtl-Ishlinskii model based internal model (d-EUPI-IM) control approach. To tackle modeling uncertainties, the robust d-EUPI-IM control approach is investigated, and the associated sufficient stabilizing conditions are derived. The advantages of the proposed controller are: it is designed and represented in discrete form, thus practical for digital devices implementation; the extended unparallel Prandtl-Ishlinskii model can precisely represent forward/inverse complex hysteretic characteristics, thus can reduce modeling uncertainties and benefits controllers design; in addition, the internal model principle based control module can be utilized as a natural oscillator for tackling periodic references tracking problem. The proposed controller was verified through comparative experiments on a piezoelectric actuator platform, and convincing results have been achieved.

OPTICAL correlation identification technology applied in underwater laser imaging target identification

NASA Astrophysics Data System (ADS)

Yao, Guang-tao; Zhang, Xiao-hui; Ge, Wei-long

2012-01-01

The underwater laser imaging detection is an effective method of detecting short distance target underwater as an important complement of sonar detection. With the development of underwater laser imaging technology and underwater vehicle technology, the underwater automatic target identification has gotten more and more attention, and is a research difficulty in the area of underwater optical imaging information processing. Today, underwater automatic target identification based on optical imaging is usually realized with the method of digital circuit software programming. The algorithm realization and control of this method is very flexible. However, the optical imaging information is 2D image even 3D image, the amount of imaging processing information is abundant, so the electronic hardware with pure digital algorithm will need long identification time and is hard to meet the demands of real-time identification. If adopt computer parallel processing, the identification speed can be improved, but it will increase complexity, size and power consumption. This paper attempts to apply optical correlation identification technology to realize underwater automatic target identification. The optics correlation identification technology utilizes the Fourier transform characteristic of Fourier lens which can accomplish Fourier transform of image information in the level of nanosecond, and optical space interconnection calculation has the features of parallel, high speed, large capacity and high resolution, combines the flexibility of calculation and control of digital circuit method to realize optoelectronic hybrid identification mode. We reduce theoretical formulation of correlation identification and analyze the principle of optical correlation identification, and write MATLAB simulation program. We adopt single frame image obtained in underwater range gating laser imaging to identify, and through identifying and locating the different positions of target, we can improve the speed and orientation efficiency of target identification effectively, and validate the feasibility of this method primarily.

Nagging, Noobs and New Tricks--Students' Perceptions of School as a Context for Digital Technology Use

ERIC Educational Resources Information Center

Bulfin, Scott; Johnson, Nicola; Nemorin, Selena; Selwyn, Neil

2016-01-01

While digital technology is an integral feature of contemporary education, schools are often presumed to constrain and compromise students' uses of technology. This paper investigates students' experiences of school as a context for digital technology use. Drawing upon survey data from three Australian secondary schools (n = 1174), this paper…

Applying Digital Sensor Technology: A Problem-Solving Approach

ERIC Educational Resources Information Center

Seedhouse, Paul; Knight, Dawn

2016-01-01

There is currently an explosion in the number and range of new devices coming onto the technology market that use digital sensor technology to track aspects of human behaviour. In this article, we present and exemplify a three-stage model for the application of digital sensor technology in applied linguistics that we have developed, namely,…

Barriers and Facilitators to Using Digital Technologies in the Cooperative Learning Model in Physical Education

ERIC Educational Resources Information Center

Bodsworth, Hannah; Goodyear, Victoria A.

2017-01-01

Background: The influence of technology on children's everyday lives is significant in today's society, with children described as digital natives and/or the iGeneration. There are also a range of digital technologies available for use in education and a number of pedagogical approaches reported to support technology integration and pupil learning…

CMOS based capacitance to digital converter circuit for MEMS sensor

NASA Astrophysics Data System (ADS)

Rotake, D. R.; Darji, A. D.

2018-02-01

Most of the MEMS cantilever based system required costly instruments for characterization, processing and also has large experimental setups which led to non-portable device. So there is a need of low cost, highly sensitive, high speed and portable digital system. The proposed Capacitance to Digital Converter (CDC) interfacing circuit converts capacitance to digital domain which can be easily processed. Recent demand microcantilever deflection is part per trillion ranges which change the capacitance in 1-10 femto farad (fF) range. The entire CDC circuit is designed using CMOS 250nm technology. Design of CDC circuit consists of a D-latch and two oscillators, namely Sensor controlled oscillator (SCO) and digitally controlled oscillator (DCO). The D-latch is designed using transmission gate based MUX for power optimization. A CDC design of 7-stage, 9-stage and 11-stage tested for 1-18 fF and simulated using mentor graphics Eldo tool with parasitic. Since the proposed design does not use resistance component, the total power dissipation is reduced to 2.3621 mW for CDC designed using 9-stage SCO and DCO.

'We have the internet in our hands': Bangladeshi college students' use of ICTs for health information.

PubMed

Waldman, Linda; Ahmed, Tanvir; Scott, Nigel; Akter, Shahinoor; Standing, Hilary; Rasheed, Sabrina

2018-03-20

Information and Communications Technologies (ICTs) which enable people to access, use and promote health information through digital technology, promise important health systems innovations which can challenge gatekeepers' control of information, through processes of disintermediation. College students, in pursuit of sexual and reproductive health (SRH) information, are particularly affected by gatekeeping as strong social and cultural norms restrict their access to information and services. This paper examines mobile phone usage for obtaining health information in Mirzapur, Bangladesh. It contrasts college students' usage with that of the general population, asks whether students are using digital technologies for health information in innovative ways, and examines how gender affects this. This study relies on two surveys: a 2013-2014 General Survey that randomly sampled 854 households drawn from the general population and a 2015 Student Survey that randomly sampled 436 students from two Mirzapur colleges. Select focus group discussions and in-depth interviews were undertaken with students. Icddr,b's Ethical Review Board granted ethical clearance. The data show that Mirzapur's college students are economically relatively well positioned, more likely to own mobile and smart phones, and more aware of the internet than the general population. They are interested in health information and use phones and computers to access information. Moreover, they use digital technology to share previously-discreet information, adding value to that information and bypassing former gatekeepers. But access to health information is not entirely unfettered, affecting male and female students differently, and powerful gatekeepers, both old and new, can still control sources of information. Personal searches for SRH and the resultant online information shared through discrete, personal face-to-face discussions has some potential to challenge social norms. This is particularly so for women students, as sharing information may enable them to bypass gatekeepers and make decisions about reproduction. This suggests that digital health information seeking may be exercising a disruptive effect within the health sector. However, the extent of this disruption may depend, not on students' mobile phone usage, but on the degree to which powerful new gatekeepers are able to retain control over and market SRH information through students' peer-to-peer sharing.

The Role of Motive Objects in Early Childhood Teacher Development Concerning Children's Digital Play and Play-Based Learning in Early Childhood Curricula

ERIC Educational Resources Information Center

Nuttall, Joce; Edwards, Susan; Mantilla, Ana; Grieshaber, Sue; Wood, Elizabeth

2015-01-01

Digital technologies are increasingly accepted as a viable aspect of early childhood curriculum. However, teacher uptake of digital technologies in early childhood education and their use with young children in play-based approaches to learning have not been strong. Traditional approaches to the problem of teacher uptake of digital technologies in…

Digital radiographic imaging: is the dental practice ready?

PubMed

Parks, Edwin T

2008-04-01

Digital radiographic imaging is slowly, but surely, replacing film-based imaging. It has many advantages over traditional imaging, but the technology also has some drawbacks. The author presents an overview of the types of digital image receptors available, image enhancement software and the range of costs for the new technology. PRACTICE IMPLICATIONS. The expenses associated with converting to digital radiographic imaging are considerable. The purpose of this article is to provide the clinician with an overview of digital radiographic imaging technology so that he or she can be an informed consumer when evaluating the numerous digital systems in the marketplace.

47 CFR 90.548 - Interoperability Technical Standards.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Specification—New Technology Standards Project—Digital Radio Technical Standards, approved March 2005. (v) ANSI/TIA-102.BAEE-B-2010, Project 25 Radio Management Protocols—New Technology Standards Project—Digital... 2003. (iii) ANSI/TIA-102.BAEA-B-2012, Project 25 Data Overview—New Technology Standards Project—Digital...

Handheld Devices with Wide-Area Wireless Connectivity: Applications in Astronomy Educational Technology and Remote Computational Control

NASA Astrophysics Data System (ADS)

Budiardja, R. D.; Lingerfelt, E. J.; Guidry, M. W.

2003-05-01

Wireless technology implemented with handheld devices has attractive features because of the potential to access large amounts of data and the prospect of on-the-fly computational analysis from a device that can be carried in a shirt pocket. We shall describe applications of such technology to the general paradigm of making digital wireless connections from the field to upload information and queries to network servers, executing (potentially complex) programs and controlling data analysis and/or database operations on fast network computers, and returning real-time information from this analysis to the handheld device in the field. As illustration, we shall describe several client/server programs that we have written for applications in teaching introductory astronomy. For example, one program allows static and dynamic properties of astronomical objects to be accessed in a remote observation laboratory setting using a digital cell phone or PDA. Another implements interactive quizzing over a cell phone or PDA using a 700-question introductory astronomy quiz database, thus permitting students to study for astronomy quizzes in any environment in which they have a few free minutes and a digital cell phone or wireless PDA. Another allows one to control and monitor a computation done on a Beowulf cluster by changing the parameters of the computation remotely and retrieving the result when the computation is done. The presentation will include hands-on demonstrations with real devices. *Managed by UT-Battelle, LLC, for the U.S. Department of Energy under contract DE-AC05-00OR22725.

Listening to Communities: Mixed-Method Study of the Engagement of Disadvantaged Mothers and Pregnant Women With Digital Health Technologies.

PubMed

Guendelman, Sylvia; Broderick, Andrew; Mlo, Hmellisa; Gemmill, Alison; Lindeman, David

2017-07-05

US health care providers are increasingly demanding patient engagement with digital health technologies to enroll in care, access personal health information, communicate with providers, and monitor their own health. Such engagement may be difficult for disadvantaged populations who may have limited health literacy, time constraints, or competing priorities. We aimed to understand the extent of adoption and use of digital health tools and to identify key perceived psychological motivators of technology use among disadvantaged first-time pregnant women and mothers of young children. We recruited women from health organizations serving low-income communities in the Midwest and on the East and West coasts. A total of 92 women participated in 14 focus groups. During each session, we administered worksheets that measured 3 utilization outcomes: the number of recent Web-based health-seeking activities, current use of digital health-management practices (eg, accessing personal health information, communicating with providers, and scheduling appointments), and potential adoption of digital health-management tools among low users or nonusers. Responses to the worksheets and to a pre-focus group survey on demographics, technology access, and motivators of use were examined to create user profiles. Separate regression models identified the motivators (eHealth literacy, internal health orientation, and trust in digital information) associated with these outcomes. Qualitative data were incorporated to illustrate the worksheet responses. Whereas 97% of the participants reported that they had searched for health information on the Internet in the past year, 42% did not engage in digital health-management practices. Among the low users and nonusers, 49% expressed interest in future adoption of digital health tools. Web-based health information-seeking activities were associated with digital health-management practices (P<.001). When controlling for covariates, eHealth literacy was positively correlated with the number of Web-based health-seeking activities (beta=.03, 95% CI 0.00-0.07). However, an internal health orientation was a much stronger correlate of digital health-management practices (beta=.13, 95% CI 0.02-0.24), whereas trust in digital information increased the odds of potential adoption (vs no adoption) in adjusted models (OR 5.21, 95% CI 0.84-32.53). Demographic characteristics were not important drivers of digital health use and few differences distinguished use among mothers and pregnant women. Seeking health information on the Internet may be an important gateway toward engaging in digital health-management practices. Notably, different consumer motivators influence digital health tool use. The relative contributions of each must be explored to design tools and interventions that enhance competencies for the management of self and child health among disadvantaged mothers and pregnant women. Unless we address disparities in digital health tool use, benefits from their use will accrue predominantly to individuals with the resources and skills to use technology effectively. ©Sylvia Guendelman, Andrew Broderick, Hmellisa Mlo, Alison Gemmill, David Lindeman. Originally published in the Journal of Medical Internet Research (http://www.jmir.org), 05.07.2017.

Use of Digital Pens for Rapid Epidemiologic Data Collection During a Foodborne Outbreak Investigation.

PubMed

Mathewson, Abigail A; Daly, Elizabeth R; Cavallo, Steffany J; Alic, Adnela

2015-08-01

Public health investigations require rapid assessment, response, and initiation of control measures. In 2012, the New Hampshire Department of Health and Human Services used digital pens to rapidly acquire epidemiologic data during a gastrointestinal illness outbreak. Menus were obtained and a standard questionnaire was administered to exposed persons using digital pens. Questionnaire data were downloaded into an electronic file for analysis. Sixty-nine (74%) of 93 exposed persons completed a questionnaire. Of 6389 data entries made on digital paper, 218 (3%) required correction; of these, 201 (92%) involved a free-form variable and 17 (8%) involved a check-box variable. Digital pens saved an estimated 5 to 6 hours of data-entry time. This outbreak provided an opportunity to assess the value of digital pens for decreasing data-entry burden and allowing more timely data analysis in an emergent setting. Depending on the size of the outbreak and complexity of the survey, there is likely a threshold when use of digital pens would provide a clear benefit to outbreak response. As new technology becomes available for use in emergency preparedness settings, public health agencies must continuously review and update response plans and evaluate investigation tools to ensure timely disease control and response activities.

Analog and digital transport of RF channels over converged 5G wireless-optical networks

NASA Astrophysics Data System (ADS)

Binh, Le Nguyen

2016-02-01

Under the exponential increase demand by the emerging 5G wireless access networking and thus data-center based Internet, novel and economical transport of RF channels to and from wireless access systems. This paper presents the transport technologies of RF channels over the analog and digital domain so as to meet the demands of the transport capacity reaching multi-Tbps, in the followings: (i) The convergence of 5G broadband wireless and optical networks and its demands on capacity delivery and network structures; (ii) Analog optical technologies for delivery of both the information and RF carriers to and from multiple-input multiple-output (MIMO) antenna sites so as to control the beam steering of MIMO antenna in the mmW at either 28.6 GHz and 56.8 GHz RF carrier and delivery of channels of aggregate capacity reaching several Tbps; (ii) Transceiver employing advanced digital modulation formats and digital signal processing (DSP) so as to provide 100G and beyond transmission rate to meet the ultra-high capacity demands with flexible spectral grids, hence pay-on-demand services. The interplay between DSP-based and analog transport techniques is examined; (iii) Transport technologies for 5G cloud access networks and associate modulation and digital processing techniques for capacity efficiency; and (iv) Finally the integrated optic technologies with novel lasers, comb generators and simultaneous dual function photonic devices for both demultiplexing/multiplexing and modulation are proposed, hence a system on chip structure can be structured. Quantum dot lasers and matrixes of micro ring resonators are integrated on the same Si-on-Silica substrate are proposed and described.

A Historical Perspective on Digital Hearing Aids: How Digital Technology Has Changed Modern Hearing Aids

PubMed Central

Levitt, Harry

2007-01-01

This article provides the author's perspective on the development of digital hearing aids and how digital signal processing approaches have led to changes in hearing aid design. Major landmarks in the evolution of digital technology are identified, and their impact on the development of digital hearing aids is discussed. Differences between analog and digital approaches to signal processing in hearing aids are identified. PMID:17301334

Electromechanical actuation for cryogenic valve control

NASA Technical Reports Server (NTRS)

Lister, M. J.; Reichmuth, D. M.

1993-01-01

The design and analysis of the electromechanical actuator (EMA) being developed for the NASA/Marshall Space Flight Center as part of the National Launch System (NLS) Propellant Control Effector Advanced Development Program (ADP) are addressed. The EMA design uses several proven technologies combined into a single modular package which includes single stage high ratio gear reduction, redundant electric motors mounted on a common drive shaft, redundant drive and control electronics, and digital technology for performing the closed loop position feedback, communication, and health monitoring functions. Results of tests aimed at evaluating both component characteristics and overall system performance demonstrated that the goal of low cost, reliable control in a cryogenic environment is feasible.

Mapping invasive weeds and their control with spatial information technologies

USDA-ARS?s Scientific Manuscript database

We discuss applications of airborne multispectral digital imaging systems, imaging processing techniques, global positioning systems (GPS), and geographic information systems (GIS) for mapping the invasive weeds giant salvinia (Salvinia molesta) and Brazilian pepper (Schinus terebinthifolius) and fo...

Digital diffractive optics: Have diffractive optics entered mainstream industry yet?

NASA Astrophysics Data System (ADS)

Kress, Bernard; Hejmadi, Vic

2010-05-01

When a new technology is integrated into industry commodity products and consumer electronic devices, and sold worldwide in retail stores, it is usually understood that this technology has then entered the realm of mainstream technology and therefore mainstream industry. Such a leap however does not come cheap, as it has a double edge sword effect: first it becomes democratized and thus massively developed by numerous companies for various applications, but also it becomes a commodity, and thus gets under tremendous pressure to cut down its production and integration costs while not sacrificing to performance. We will show, based on numerous examples extracted from recent industry history, that the field of Diffractive Optics is about to undergo such a major transformation. Such a move has many impacts on all facets of digital diffractive optics technology, from the optical design houses to the micro-optics foundries (for both mastering and volume replication), to the final product integrators or contract manufacturers. The main causes of such a transformation are, as they have been for many other technologies in industry, successive technological bubbles which have carried and lifted up diffractive optics technology within the last decades. These various technological bubbles have been triggered either by real industry needs or by virtual investment hype. Both of these causes will be discussed in the paper. The adjective ""digital"" in "digital diffractive optics" does not refer only, as it is done in digital electronics, to the digital functionality of the element (digital signal processing), but rather to the digital way they are designed (by a digital computer) and fabricated (as wafer level optics using digital masking techniques). However, we can still trace a very strong similarity between the emergence of micro-electronics from analog electronics half a century ago, and the emergence of digital optics from conventional optics today.

Object-Based Teaching and Learning for a Critical Assessment of Digital Technologies in Arts and Cultural Heritage

NASA Astrophysics Data System (ADS)

Hess, M.; Garside, D.; Nelson, T.; Robson, S.; Weyrich, T.

2017-08-01

As cultural sector practice becomes increasingly dependent on digital technologies for the production, display, and dissemination of art and material heritage, it is important that those working in the sector understand the basic scientific principles underpinning these technologies and the social, political and economic implications of exploiting them. The understanding of issues in cultural heritage preservation and digital heritage begins in the education of the future stakeholders and the innovative integration of technologies into the curriculum. This paper gives an example of digital technology skills embedded into a module in the interdisciplinary UCL Bachelor of Arts and Sciences, named "Technologies in Arts and Cultural Heritage", at University College London.

The Learning Preferences of Digital Learners in K-12 Schools in China

ERIC Educational Resources Information Center

Yang, Junfeng; Huang, Ronghuai; Kinshuk

2016-01-01

Students grown up with digital technology and Internet are called digital natives or net generation. All others, who grew up without so much immersion with digital technologies are called digital immigrants. Researchers held different ideas on whether a new generation of learners existed. One of the foci of the debate is on the appropriateness of…

Incorporating digital imaging into dental hygiene practice.

PubMed

Saxe, M J; West, D J

1997-01-01

The objective of this paper is to describe digital imaging technology: available modalities, scientific imaging process, advantages and limitations, and applications to dental hygiene practice. Advances in technology have created innovative imaging modalities for intraoral radiography that eliminate film as the traditional image receptor. Digital imaging generates instantaneous radiographic images on a display monitor following exposure. Advantages include lower patient exposure per image and elimination of film processing. Digital imaging enhances diagnostic capabilities and, therefore, treatment decisions by the oral healthcare provider. Utilization of digital imaging technology for intraoral radiography will advance the practice of dental hygiene. Although spatial resolution is inferior to conventional film, digital imaging provides adequate resolution to diagnose oral diseases. Dental hygienists must evaluate new technologies in radiography to continue providing quality care while reducing patient exposure to ionizing radiation.

The Effectiveness of Prompts to Promote Engagement With Digital Interventions: A Systematic Review.

PubMed

Alkhaldi, Ghadah; Hamilton, Fiona L; Lau, Rosa; Webster, Rosie; Michie, Susan; Murray, Elizabeth

2016-01-08

Digital interventions have been effective in improving numerous health outcomes and health behaviors; furthermore, they are increasingly being used in different health care areas, including self-management of long-term conditions, mental health, and health promotion. The full potential of digital interventions is hindered by a lack of user engagement. There is an urgent need to develop effective strategies that can promote users' engagement with digital interventions. One potential method is the use of technology-based reminders or prompts. To evaluate the effectiveness of technology-based strategies for promoting engagement with digital interventions. Cochrane Collaboration guidelines on systematic review methodology were followed. The search strategy was executed across 7 electronic databases: the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE, Embase, Web of Science, the Education Resources Information Center (ERIC), PsycINFO, and the Cumulative Index to Nursing and Allied Health Literature (CINAHL). Databases were searched from inception to September 13, 2013, with no language or publication type restrictions, using three concepts: randomized controlled trials, digital interventions, and engagement. Gray literature and reference lists of included studies were also searched. Titles and abstracts were independently screened by 2 authors, then the full texts of potentially eligible papers were obtained and double-screened. Data from eligible papers were extracted by one author and checked for accuracy by another author. Bias was assessed using the Cochrane risk of bias assessment tool. Narrative synthesis was performed on all included studies and, where appropriate, data were pooled using meta-analysis. All findings were reported according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. A total of 14 studies were included in the review with 8774 participants. Of the 14 studies, 9 had sufficient data to be included in the meta-analyses. The meta-analyses suggested that technology-based strategies can potentially promote engagement compared to no strategy for dichotomous outcomes (relative risk [RR] 1.27, 95% CI 1.01-1.60, I(2)=71%), but due to considerable heterogeneity and the small sample sizes in most studies, this result should be treated with caution. No studies reported adverse or economic outcomes. Only one study with a small sample size compared different characteristics; the study found that strategies promoting new digital intervention content and those sent to users shortly after they started using the digital intervention were more likely to engage users. Overall, studies reported borderline positive effects of technology-based strategies on engagement compared to no strategy. However, the results have to be interpreted with caution. More research is needed to replicate findings and understand which characteristics of the strategies are effective in promoting engagement and how cost-effective they are.

Approach to spatial information security based on digital certificate

NASA Astrophysics Data System (ADS)

Cong, Shengri; Zhang, Kai; Chen, Baowen

2005-11-01

With the development of the online applications of geographic information systems (GIS) and the spatial information services, the spatial information security becomes more important. This work introduced digital certificates and authorization schemes into GIS to protect the crucial spatial information combining the techniques of the role-based access control (RBAC), the public key infrastructure (PKI) and the privilege management infrastructure (PMI). We investigated the spatial information granularity suited for sensitivity marking and digital certificate model that fits the need of GIS security based on the semantics analysis of spatial information. It implements a secure, flexible, fine-grained data access based on public technologies in GIS in the world.

Digitization of Microfilm: A Scottish Perspective.

ERIC Educational Resources Information Center

Lauder, John

1995-01-01

Discusses the Scottish Newspapers Microfilming Unit's interest in conversion of microfilm to digital technology. Concerns include cost, potential market, reliability of digital technology as a preservation medium, and the necessity to have both microfilm and digital formats for preservation. Solicits feedback and information from colleagues on the…

Integrating Digital Video Technology in the Classroom

ERIC Educational Resources Information Center

Lim, Jon; Pellett, Heidi Henschel; Pellett, Tracy

2009-01-01

Digital video technology can be a powerful tool for teaching and learning. It enables students to develop a variety of skills including research, communication, decision-making, problem-solving, and other higher-order critical-thinking skills. In addition, digital video technology has the potential to enrich university classroom curricula, enhance…

CONTENTdm Digital Collection Management Software and End-User Efficacy

ERIC Educational Resources Information Center

Dickson, Maggie

2008-01-01

Digital libraries and collections are a growing facet of today's traditional library. Digital library technologies have become increasingly more sophisticated in the effort to provide more and better access to the collections they contain. The evaluation of the usability of these technologies has not kept pace with technological developments,…

Digital Literacy - Is It Necessary for eInclusion?

NASA Astrophysics Data System (ADS)

Leahy, Denise; Dolan, Dudley

In order to live and work in today's technological world, it is important to be able to use information and communications technology. More and more of us are communicating with family and friends using technology; business is carried out using technology; in the work environment companies use intranets to communicate with staff; governments are moving towards interacting with citizens online. While accessibility and usability in technology are absolutely necessary, is digital literacy a pre-requisite to benefit from what the Information Society can offer? The EU has recognised the need for digital literacy and has included this in the definition of eInclusion [1]. This paper examines definitions of digital literacy and suggests that digital literacy is necessary for a person to take a full part in today's Information Society.

The digital pen and paper technology: implementation and use in an existing clinical information system.

PubMed

Despont-Gros, Christelle; Bœuf, Christophe; Geissbuhler, Antoine; Lovis, Christian

2005-01-01

Evaluation of the technical feasibility of tight integration of the digital pen and paper technology in an existing computerized patient record.Technology: The digital pen is a normal pen able to record all actions of the user and to analyze a micro pattern printed on the paper. The digital paper is a normal paper printed with an almost invisible micro pattern of small dots encoding information such as position and identifiers. We report our experience in the implementation and the use of this technology in an existing large clinical information system for acquiring clinical information. It is possible to print uniquely identified forms using the digital paper technology. These forms can be pre-filled with clinical readable information about the patient. When care providers complete these forms using the digital pen, it is possible to acquire the data in a structured computerized patient record. The technology is easy to integrate in a component-based architecture based on Web Services. The digital pen and paper is a cost-effective technology that can be integrated in an existing clinical information system and allows fast and easy bedside clinical information acquisition without the need for an expensive infrastructure based on traditional portable devices or wireless devices.

Closing the design loop on HiMAT (highly maneuverable aircraft technology)

NASA Technical Reports Server (NTRS)

Putnam, T. W.; Robinson, M. R.

1984-01-01

The design methodology used in the HiMAT program and the wind tunnel development activities are discussed. Selected results from the flight test program are presented and the strengths and weaknesses of testing advanced technology vehicles using the RPV concept is examined. The role of simulation on the development of digital flight control systems and in RPV's in particular is emphasized.

Enhancing Student Interactions with the Instructor and Content Using Pen-Based Technology, YouTube Videos, and Virtual Conferencing

ERIC Educational Resources Information Center

Cox, James R.

2011-01-01

This report describes the incorporation of digital learning elements in organic chemistry and biochemistry courses. The first example is the use of pen-based technology and a large-format PowerPoint slide to construct a map that integrates various metabolic pathways and control points. Students can use this map to visualize the integrated nature…

Development of Coriolis mass flowmeter with digital drive and signal processing technology.

PubMed

Hou, Qi-Li; Xu, Ke-Jun; Fang, Min; Liu, Cui; Xiong, Wen-Jun

2013-09-01

Coriolis mass flowmeter (CMF) often suffers from two-phase flowrate which may cause flowtube stalling. To solve this problem, a digital drive method and a digital signal processing method of CMF is studied and implemented in this paper. A positive-negative step signal is used to initiate the flowtube oscillation without knowing the natural frequency of the flowtube. A digital zero-crossing detection method based on Lagrange interpolation is adopted to calculate the frequency and phase difference of the sensor output signals in order to synthesize the digital drive signal. The digital drive approach is implemented by a multiplying digital to analog converter (MDAC) and a direct digital synthesizer (DDS). A digital Coriolis mass flow transmitter is developed with a digital signal processor (DSP) to control the digital drive, and realize the signal processing. Water flow calibrations and gas-liquid two-phase flowrate experiments are conducted to examine the performance of the transmitter. The experimental results show that the transmitter shortens the start-up time and can maintain the oscillation of flowtube in two-phase flowrate condition. Copyright © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Comparison of speech recognition with adaptive digital and FM remote microphone hearing assistance technology by listeners who use hearing aids.

PubMed

Thibodeau, Linda

2014-06-01

The purpose of this study was to compare the benefits of 3 types of remote microphone hearing assistance technology (HAT), adaptive digital broadband, adaptive frequency modulation (FM), and fixed FM, through objective and subjective measures of speech recognition in clinical and real-world settings. Participants included 11 adults, ages 16 to 78 years, with primarily moderate-to-severe bilateral hearing impairment (HI), who wore binaural behind-the-ear hearing aids; and 15 adults, ages 18 to 30 years, with normal hearing. Sentence recognition in quiet and in noise and subjective ratings were obtained in 3 conditions of wireless signal processing. Performance by the listeners with HI when using the adaptive digital technology was significantly better than that obtained with the FM technology, with the greatest benefits at the highest noise levels. The majority of listeners also preferred the digital technology when listening in a real-world noisy environment. The wireless technology allowed persons with HI to surpass persons with normal hearing in speech recognition in noise, with the greatest benefit occurring with adaptive digital technology. The use of adaptive digital technology combined with speechreading cues would allow persons with HI to engage in communication in environments that would have otherwise not been possible with traditional wireless technology.

Digital Reading: A Question of Prelectio?

ERIC Educational Resources Information Center

Fitzpatrick, Noel

2013-01-01

Digital reading as superficial reading is examined by demonstrating that technologies act as placeholders for different types of memory, artificial memory and true memory. This chapter argues that the affordances of digital technologies enable certain types of reading activity, digital reading, but hinders others, such as deep reading. In…

An Investigation of Middle School Science Teachers and Students Use of Technology inside and outside of Classrooms: Considering Whether Digital Natives Are More Technology Savvy than Their Teachers

ERIC Educational Resources Information Center

Wang, Shiang-Kwei; Hsu, Hui-Yin; Campbell, Todd; Coster, Daniel C.; Longhurst, Max

2014-01-01

The purpose of the study is to investigate the popular assumption that the "digital natives" generation surpasses the previous "digital immigrants" generation in terms of their technology experiences, because they grow up with information and communication technology. The assumption presumes that teachers, the digital…

Data management in NOAA

NASA Technical Reports Server (NTRS)

Callicott, William M.

1992-01-01

NOAA has 11 terabytes of digital data stored on 240,000 computer tapes. There are an additional 100 terabytes (TB) of geostationary satellite data stored in digital form on specially configured SONY U-Matic video tapes at the University of Wisconsin. There are over 90,000,000 non-digital form records in manuscript, film, printed, and chart form which are not easily accessible. The three NOAA Data Centers service 6,000 requests per year and publish 5,000 bulletins which are distributed to 40,000 subscribers. Seventeen CD-ROM's have been produced. Thirty thousand computer tapes containing polar satellite data are being copied to 12 inch WORM optical disks for research applications. The present annual data accumulation rate of 10 TB will grow to 30 TB in 1994 and to 100 TB by the year 2000. The present storage and distribution technologies with their attendant support systems will be overwhelmed by these increases if not improved. Increased user sophistication coupled with more precise measurement technologies will demand better quality control mechanisms, especially for those data maintained in an indefinite archive. There is optimism that the future will offer improved media technologies to accommodate the volumes of data. With the advanced technologies, storage and performance monitoring tools will be pivotal to the successful long-term management of data and information.

77 FR 26786 - Certain Products Containing Interactive Program and Parental Control Technology; Notice of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-07

.... of CA; Mitsubishi Digital Electronics America, Inc. of CA; Netflix Inc. of CA; Roku, Inc. of CA; and... public health and welfare in the United States, competitive conditions in the United States economy, the...

Development of CMOS Active Pixel Image Sensors for Low Cost Commercial Applications

NASA Technical Reports Server (NTRS)

Gee, R.; Kemeny, S.; Kim, Q.; Mendis, S.; Nakamura, J.; Nixon, R.; Ortiz, M.; Pain, B.; Staller, C.; Zhou, Z;

Advanced digital image archival system using MPEG technologies

NASA Astrophysics Data System (ADS)

Chang, Wo

2009-08-01

Digital information and records are vital to the human race regardless of the nationalities and eras in which they were produced. Digital image contents are produced at a rapid pace from cultural heritages via digitalization, scientific and experimental data via high speed imaging sensors, national defense satellite images from governments, medical and healthcare imaging records from hospitals, personal collection of photos from digital cameras. With these mass amounts of precious and irreplaceable data and knowledge, what standards technologies can be applied to preserve and yet provide an interoperable framework for accessing the data across varieties of systems and devices? This paper presents an advanced digital image archival system by applying the international standard of MPEG technologies to preserve digital image content.

[Telepsychiatry provides new opportunities for the prevention and treatment of mental health disorders].

PubMed

Folker, Marie Paldam; Helverskov, Trine; Nielsen, Amalie Søgaard; Jørgensen, Ulla Skov; Larsen, John Teilmann

2018-04-23

Digital technologies in mental healthcare are envisioned to offer easier, faster and more cost-effective access to mental healthcare. The scope for integrating digital technology into mental healthcare is vast: video conferencing, developing novel treatments using interactive software, mobile applications, and sensor technologies. We outline technology-based interventions, which are relevant to clinical practice, and present the evidence base for using digital technology as well as emerging challenges for their implementation in clinical practice.

High Rate Digital Demodulator ASIC

NASA Technical Reports Server (NTRS)

Ghuman, Parminder; Sheikh, Salman; Koubek, Steve; Hoy, Scott; Gray, Andrew

1998-01-01

The architecture of High Rate (600 Mega-bits per second) Digital Demodulator (HRDD) ASIC capable of demodulating BPSK and QPSK modulated data is presented in this paper. The advantages of all-digital processing include increased flexibility and reliability with reduced reproduction costs. Conventional serial digital processing would require high processing rates necessitating a hardware implementation in other than CMOS technology such as Gallium Arsenide (GaAs) which has high cost and power requirements. It is more desirable to use CMOS technology with its lower power requirements and higher gate density. However, digital demodulation of high data rates in CMOS requires parallel algorithms to process the sampled data at a rate lower than the data rate. The parallel processing algorithms described here were developed jointly by NASA's Goddard Space Flight Center (GSFC) and the Jet Propulsion Laboratory (JPL). The resulting all-digital receiver has the capability to demodulate BPSK, QPSK, OQPSK, and DQPSK at data rates in excess of 300 Mega-bits per second (Mbps) per channel. This paper will provide an overview of the parallel architecture and features of the HRDR ASIC. In addition, this paper will provide an over-view of the implementation of the hardware architectures used to create flexibility over conventional high rate analog or hybrid receivers. This flexibility includes a wide range of data rates, modulation schemes, and operating environments. In conclusion it will be shown how this high rate digital demodulator can be used with an off-the-shelf A/D and a flexible analog front end, both of which are numerically computer controlled, to produce a very flexible, low cost high rate digital receiver.

Teaching conceptions of the use of digital technologies as a teaching resource in physical education in public schools of Minas Gerais, Brazil

NASA Astrophysics Data System (ADS)

Voelzke, M. R.; Paganotti, A.; Assis, A. M. M.

2017-07-01

Increasingly, digital technologies have been invading classrooms, providing more and more attractive teaching methods for both, students and teachers. The arrival of digital technologies in classrooms brings great advances, but also many uncertainties and insecurities to teachers. With current technologies, the school environment can transform into a meaningful learning ambience with a more active and interactive student. This research aimed to analyze the opinion of eleven teachers who teach in four public schools in the interior of Minas Gerais, about the challenges of using digital technologies at school everyday. The data were obtained from the application of a questionnaire with eight questions. One of those asked about the used of digital technologies in the classroom, ten professors claimed to use them, but in another question that inquired about their knowledge about simulation software for physics teaching, only six said they knew about this resource. When questioned about the lecture on the topic of technological development, only seven teachers stated that they use this technique, being a relatively small number. Out of the four surveyed schools, two had digital slates, but the teachers said they did not use them because they did not receive any training. It was concluded that teachers do not feel comfortable teaching physics using digital technological resources, apparently because they lack adequate training. In many schools either there is no equipment or the same exists, but the teachers did not undergo training to use them. It is noticed that in the XXI century teachers insist on the traditional teaching model, contrary to the current trends to which students are immersed in a digital and interactive technological world.

Digital Ink and Notetaking

ERIC Educational Resources Information Center

Colwell, Kenneth E.

2004-01-01

Tablet PCs and graphics tablets employ digital ink technology. In this paper the author introduces the reader to digital ink technology with the aim of promoting its use in various instructional or training settings, with the goal of improving instructor-learner dialogue and student learning. The potential of digital ink for improved instructional…

Digital Citizenship

ERIC Educational Resources Information Center

Isman, Aytekin; Canan Gungoren, Ozlem

2014-01-01

Era in which we live is known and referred as digital age.In this age technology is rapidly changed and developed. In light of these technological advances in 21st century, schools have the responsibility of training "digital citizen" as well as a good citizen. Digital citizens must have extensive skills, knowledge, Internet and …

76 FR 80417 - Request for Information: Public Access to Digital Data Resulting From Federally Funded Scientific...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-23

... OFFICE OF SCIENCE AND TECHNOLOGY POLICY Request for Information: Public Access to Digital Data... public access to unclassified digital data that result from federally funded scientific research. The... Technology Council's Interagency Working Group on Digital Data. Release Date: November 3, 2011. Response Date...

Secondary School Teachers' Approaches to Teaching Composition Using Digital Technology

ERIC Educational Resources Information Center

Wise, Stuart

2016-01-01

The music industry in the 21 century uses digital technology in a wide range of applications including in performance, in composition and in recording and publishing. In this article, I consider how the impact of digital technologies may be affecting pedagogical processes adopted by secondary music teachers, particularly in the area of…

Digital Technologies: From Vision to Action

ERIC Educational Resources Information Center

Armistead, Stuart

2016-01-01

The interest and uptake in utilising digital technologies in education appears to be exponential. With the rollout of ultrafast broadband and the development of the Network for Learning in New Zealand, school leaders face the challenges and opportunity of deciding when, what and how they go about implementing digital technologies in their schools.…

What Works and Why? Student Perceptions of "Useful" Digital Technology in University Teaching and Learning

ERIC Educational Resources Information Center

Henderson, Michael; Selwyn, Neil; Aston, Rachel

2017-01-01

Digital technologies are now an integral aspect of the university student experience. As such, academic research has understandably focused on the potential of various digital technologies to enable, extend and even "enhance" student learning. This paper offers an alternate perspective on these issues by exploring students' actual…

Validity of Subjective Self-Assessment of Digital Competence among Undergraduate Preservice Teachers

ERIC Educational Resources Information Center

Maderick, Joseph Andrew

2013-01-01

Technology is now integrated into the Technological Pedagogical Content Knowledge (TPACK) required to be a highly qualified 21st century teacher. Accurate measurement of digital competence has become critical. Self-assessment has been used widely to measure the digital competence of preservice teachers who are expected to integrate technology into…

iGeneration: The Social Cognitive Effects of Digital Technology on Teenagers

ERIC Educational Resources Information Center

Ives, Eugenia A.

2012-01-01

The purpose of this study was to examine and better understand the social cognitive effects of digital technology on teenagers' brains and their socialization processes, as well as to learn best practices with regard to digital technology consumption. An extensive literature review was conducted on the social cognitive effects of digital…

Technology Knowledge Self-Assessment and Pre-Test Performance among Digital Natives

ERIC Educational Resources Information Center

Nelms, Keith R.

2015-01-01

According to education pundits, traditional-age college students are "digital natives" inherently savvy in digital technology due to their constant exposure to technology from an early age. This widely held meme is at odds with observation in the college classroom. In this research, college students in an introductory information…

Agriscience Teachers' Implementation of Digital Game-Based Learning in an Introductory Animal Science Course

ERIC Educational Resources Information Center

Webb, Angela W.; Bunch, J. C.; Wallace, Maria F.

2015-01-01

In today's technological age, visions for technology integration in the classroom continue to be explored and examined. Digital game-based learning is one way to purposefully integrate technology while maintaining a focus on learning objectives. This case study sought to understand agriscience teachers' experiences implementing digital game-based…

Digital Media and Technology in Afterschool Programs, Libraries, and Museums

ERIC Educational Resources Information Center

Herr-Stephenson, Becky; Rhoten, Diana; Perkel, Dan; Sims, Christo

2011-01-01

Digital media and technology have become culturally and economically powerful parts of contemporary middle-class American childhoods. Immersed in various forms of digital media as well as mobile and Web-based technologies, young people today appear to develop knowledge and skills through participation in media. This MacArthur Report examines the…

A Professional Learning Model Supporting Teachers to Integrate Digital Technologies

ERIC Educational Resources Information Center

Sheffield, Rachel; Blackley, Susan; Moro, Paul

2018-01-01

Contemporary teachers have an obligation to support and scaffold students' learning in digital technologies and to do this in authentic contexts. In order for teachers to be successful in this, their own competency in digital technologies needs to be high, and their own 21st century learning skills of communication, collaboration, creativity and…

Students' Everyday Engagement with Digital Technology in University: Exploring Patterns of Use and "Usefulness"

ERIC Educational Resources Information Center

Henderson, Michael; Selwyn, Neil; Finger, Glenn; Aston, Rachel

2015-01-01

The much-discussed potential of "technology-enhanced learning" is not always apparent in the day-to-day use of digital technology throughout higher education. Against this background, the present paper considers the digital devices and resources that students engage most frequently with during their university studies, what these…

Embracing Digital Technologies in Classroom Practice: The Impact of Teacher Identity

ERIC Educational Resources Information Center

Abbott, Rosemary

2016-01-01

It is often perceived that learning in 21st century classrooms will involve extensive use of digital technologies. This paper, based on a qualitative research investigation at a private girls' college in Melbourne, explores the impact of teacher subjectivities on the need to change through the integration of digital technologies into classroom…

Comic Relief: Graduate Students Address Multiple Meanings for Technology Integration with Digital Comic Creation

ERIC Educational Resources Information Center

Sockman, Beth Rajan; Sutton, Rhonda; Herrmann, Michele

2016-01-01

This study determined the usefulness of digital comic creation with 77 graduate students in a teacher technology course. Students completed an assigned reading and created digital comics that addressed technology integration concerns in the schools and society. Using practical action research, 77 student-created comics were analyzed. The findings…

Application of Digital Technology and PDA+APPS Mobile Terminal in Historical Architecture Culture Protection and Development

NASA Astrophysics Data System (ADS)

Liu, Zhi Feng; Wang, Ying; Huang, Dong Hui

2018-06-01

In the wake of big data and Internet plus era, continuous infiltration of digital technology has been happening in various fields of social and economic development. As the most important material carrier of historical culture, the historical value of historical buildings is produced and accumulated in its historical evolution, and it can only be protected from being created again. Based on the background of digitization of cultural resources, this paper summarizes the relevant digital technologies for the digital translation of information on buildings of historical and cultural heritage, as a means to promote the spread of the PDA+APPS mobile terminal, so as to achieve the purpose of preservation, protection, management and publicity. Meanwhile, this paper analyzes the application of digital technology in this field and the prospect of its function.

Rethinking Teaching in STEM Education in a Community College: Role of Instructional Consultation and Digital Technologies

NASA Astrophysics Data System (ADS)

Kurland, Shelley Chih-Hsian

Community college faculty members educate almost half of all U.S. undergraduates, who are often more diverse and more academically underprepared when compared to undergraduate students who attend four-year institutions. In addition, faculty members in community colleges are facing increased accountability for meeting student learning outcomes, expectations to adjust their teaching practices to include active learning practices, and expectations to incorporate more technologies into the classroom. Faculty developers are one of the support structures that faculty members can look to in order to meet those challenges. A survey of literature in faculty development suggests that instructional consultation can play an important role in shaping and transforming teaching practices. Hence, this action research study examined my work using instructional consulting with four full-time STEM faculty colleagues in order to examine and shape their teaching practices with and without the use of digital technologies. The two foci of the research, examining shifts in faculty participants' teaching practices, and my instructional consulting practices, were informed by Thomas and Brown's (2011) social view of learning and the concept of teaching and learning in a "co-learning" environment. Two dominant factors emerged regarding faculty participants' shift in teaching practices. These factors concerned: 1) the perception of control and 2) individual faculty participant's comfort level, expectations, and readiness. In addition to these two dominant factors, the instructional consultation process also supported a range of shifts in either mindset and/or teaching practices. My analysis showed that the use of digital technologies was not an essential factor in shifting faculty participant mindset and/or teaching practices, instead digital technologies were used to enhance the teaching process and students' learning experiences.

The precision-processing subsystem for the Earth Resources Technology Satellite.

NASA Technical Reports Server (NTRS)

Chapelle, W. E.; Bybee, J. E.; Bedross, G. M.

1972-01-01

Description of the precision processor, a subsystem in the image-processing system for the Earth Resources Technology Satellite (ERTS). This processor is a special-purpose image-measurement and printing system, designed to process user-selected bulk images to produce 1:1,000,000-scale film outputs and digital image data, presented in a Universal-Transverse-Mercator (UTM) projection. The system will remove geometric and radiometric errors introduced by the ERTS multispectral sensors and by the bulk-processor electron-beam recorder. The geometric transformations required for each input scene are determined by resection computations based on reseau measurements and image comparisons with a special ground-control base contained within the system; the images are then printed and digitized by electronic image-transfer techniques.

Facilitating the adoption of digital technologies by the elderly.

PubMed

Loiseau, Séverine; Boog, César; Pelayo, Sylvia

2015-01-01

This study examined the major criteria needed to facilitate the adoption of a technology that aims to support elderly autonomy. A User Centered Design process was instigated to design a digital tablet-based application. The two first stages consisted of a literature review and two focus groups that aimed respectively: to specify interaction principles, and to define the needs and expectations of the elderly and collect their feedback on the application's usability. The results show that to be accepted the technology has to provide relevant and useful information on nearby services, aids and social activities. It also has to facilitate the controlled sharing of information and the communication with close family/relations, and residential home and external services to both empower the elderly and counter loneliness. A summative evaluation will be organised after taking into account the current guidelines to further validate the usability of the application with elderly people.

Lightning protection of full authority digital electronic systems

NASA Astrophysics Data System (ADS)

Crofts, David

1991-08-01

Modern electronic systems are vulnerable to transient and they now provide safety critical functions such as full authority digital electronic control (FADEC) units for fly by wire aircraft. Of the traditional suppression technologies available diodes have gained the wider acceptance, however, they lack the current handling capacity to meet existing threat levels. The development of high speed fold back devices where, at a specified voltage, the off state resistance switches to a very low on state one has provided the equivalent to a semiconductor spark gap. The size of the technology enables it to be integrated into connectors of interconnection cables. To illustrate the performance the technology was developed to meet the Lightning Protection requirements for FADEC units within aeroengines. Work was also carried out to study switching behavior with the waveform 5, the 500 us, 10 kA pulse applied to cable assemblies. This test enabled all the switches in a connector to be fired simultaneously.

Lightning protection of full authority digital electronic systems

NASA Technical Reports Server (NTRS)

Crofts, David

1991-01-01

Modern electronic systems are vulnerable to transient and they now provide safety critical functions such as full authority digital electronic control (FADEC) units for fly by wire aircraft. Of the traditional suppression technologies available diodes have gained the wider acceptance, however, they lack the current handling capacity to meet existing threat levels. The development of high speed fold back devices where, at a specified voltage, the off state resistance switches to a very low on state one has provided the equivalent to a semiconductor spark gap. The size of the technology enables it to be integrated into connectors of interconnection cables. To illustrate the performance the technology was developed to meet the Lightning Protection requirements for FADEC units within aeroengines. Work was also carried out to study switching behavior with the waveform 5, the 500 us, 10 kA pulse applied to cable assemblies. This test enabled all the switches in a connector to be fired simultaneously.

Instruments speak global language

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nudo, L.

1993-07-01

If all goes as planned, companies that use instruments for measurement and control will get more complete, reliable and repeatable information about their processes with advanced digital devices that speak a global language. That language, in technical terms, is known as international fieldbus. But it's not much different from English's role as the international language of business. Companies that use a remote measurement device for environmental applications, such as pH control and fugitive emissions control, are candidates for fieldbus devices, which are much faster and measure more process variables than their counterpart analog devices. With the advent of a globalmore » fieldbus, users will see digital valves, solenoids and multivariable transmitters. Fieldbus technology redefines the roles of the control system and field devices. The control system still serves as a central clearinghouse, but field devices will handle more control and reporting functions and generate data that can be used for trending and preventive maintenance.« less

Flight testing the Digital Electronic Engine Control (DEEC) A unique management experience

NASA Technical Reports Server (NTRS)

Putnam, T. W.; Burcham, F. W., Jr.; Kock, B. M.

1983-01-01

The concept for the DEEC had its origin in the early 1970s. At that time it was recognized that the F100 engine performance, operability, reliability, and cost could be substantially improved by replacing the original mechanical/supervisory electronic control system with a full-authority digital control system. By 1978, the engine manufacturer had designed and initiated the procurement of flight-qualified control system hardware. As a precursor to an integrated controls program, a flight evaluation of the DEEC system on the F-15 aircraft was proposed. Questions regarding the management of the DEEC flight evaluation program are discussed along with the program elements, the technical results of the F-15 evaluation, and the impact of the flight evaluation on after-burning turbofan controls technology and its use in and application to military aircraft. The lessons learned through the conduct of the program are discussed.

Digital imaging in dentistry.

PubMed

Essen, S Donovan

2011-01-01

Information technology is vital to operations, marketing, accounting, finance and administration. One of the most exciting and quickly evolving technologies in the modern dental office is digital applications. The dentist is often the business manager, information technology officer and strategic planning chief for his small business. The information systems triangle applies directly to this critical manager supported by properly trained ancillary staff and good equipment. With emerging technology driving all medical disciplines and the rapid pace at which it emerges, it is vital for the contemporary practitioner to keep abreast of the newest information technology developments. This article compares the strategic and operational advantages of digital applications, specifically imaging. The focus of this paper will be on digital radiography (DR), 3D computerized tomography, digital photography and digitally-driven CAD/CAM to what are now considered obsolescing modalities and contemplates what may arrive in the future. It is the purpose of this essay to succinctly evaluate the decisions involved in the role, application and implications of employing this tool in the dental environment

Value of wireless personal digital assistants for practice: perceptions of advanced practice nurses.

PubMed

Garrett, Bernard; Klein, Gerri

2008-08-01

The aims were to explore advanced practice nurses' perceptions on wireless Personal Digital Assistant technologies, to establish the type and range of tools that would be useful to support their practice and to identify any requirements and limitations that may impact the implementation of wireless Personal Digital Assistants in practice. The wireless Personal Digital Assistant is becoming established as a hand-held computing tool for healthcare professionals. The reflections of advanced practice nurses' about the value of wireless Personal Digital Assistants and its potential to contribute to improved patient care has not been investigated. A qualitative interpretivist design was used to explore advanced practice nurses' perceptions on the value of wireless Personal Digital Assistant technologies to support their practice. The data were collected using survey questionnaires and individual and focus group interviews with nurse practitioners, clinical nurse specialists and information technology managers based in British Columbia, Canada. An open-coding content analysis was performed using qualitative data analysis software. Wireless Personal Digital Assistant's use supports the principles of pervasivity and is a technology rapidly being adopted by advanced practice nurses. Some nurses indicated a reluctance to integrate wireless Personal Digital Assistant technologies into their practices because of the cost and the short technological life cycle of these devices. Many of the barriers which precluded the use of wireless networks within facilities are being removed. Nurses demonstrated a complex understanding of wireless Personal Digital Assistant technologies and gave good rationales for its integration in their practice. Nurses identified improved client care as the major benefit of this technology in practice and the type and range of tools they identified included clinical reference tools such as drug and diagnostic/laboratory reference applications and wireless communications. Nurses in this study support integrating wireless mobile computing technologies into their practice to improve client care.

Digital Tablet PCs as New Technologies of Writing and Learning: A Survey of Perceptions of Digital Ink Technology

ERIC Educational Resources Information Center

Reins, Kevin

2007-01-01

The purpose of this study was to investigate effective uses of digital ink technology in an elementary mathematics methods course. A survey methodology was used in the study to examine the participants' perceptions toward this technology for teaching and learning. All of the items on the survey produced response means between 5.0 and 6.0, with a…

How Has the Internet Reshaped Human Cognition?

PubMed

Loh, Kep Kee; Kanai, Ryota

2016-10-01

Throughout our evolutionary history, our cognitive systems have been altered by the advent of technological inventions such as primitive tools, spoken language, writing, and arithmetic systems. Thirty years ago, the Internet surfaced as the latest technological invention poised to deeply reshape human cognition. With its multifaceted affordances, the Internet environment has profoundly transformed our thoughts and behaviors. Growing up with Internet technologies, "Digital Natives" gravitate toward "shallow" information processing behaviors characterized by rapid attention shifting and reduced deliberations. They engage in increased multitasking behaviors that are linked to increased distractibility and poor executive control abilities. Digital natives also exhibit higher prevalence of Internet-related addictive behaviors that reflect altered reward-processing and self-control mechanisms. Recent neuroimaging investigations have suggested associations between these Internet-related cognitive impacts and structural changes in the brain. Against mounting apprehension over the Internet's consequences on our cognitive systems, several researchers have lamented that these concerns were often exaggerated beyond existing scientific evidence. In the present review, we aim to provide an objective overview of the Internet's impacts on our cognitive systems. We critically discuss current empirical evidence about how the Internet environment has altered the cognitive behaviors and structures involved in information processing, executive control, and reward-processing. © The Author(s) 2015.

Research and development of a digital design system for hull structures

NASA Astrophysics Data System (ADS)

Zhan, Yi-Ting; Ji, Zhuo-Shang; Liu, Yin-Dong

2007-06-01

Methods used for digital ship design were studied and formed the basis of a proposed frame model suitable for ship construction modeling. Based on 3-D modeling software, a digital design system for hull structures was developed. Basic software systems for modeling, modifying, and assembly simulation were developed. The system has good compatibility, and models created by it can be saved in different 3-D file formats, and 2D engineering drawings can be output directly. The model can be modified dynamically, overcoming the necessity of repeated modifications during hull structural design. Through operations such as model construction, intervention inspection, and collision detection, problems can be identified and modified during the hull structural design stage. Technologies for centralized control of the system, database management, and 3-D digital design are integrated into this digital model in the preliminary design stage of shipbuilding.

A Hearing Aid Primer 1

ERIC Educational Resources Information Center

Yetter, Carol J.

2009-01-01

This hearing aid primer is designed to define the differences among the three levels of hearing instrument technology: conventional analog circuit technology (most basic), digitally programmable/analog circuit technology (moderately advanced), and fully digital technology (most advanced). Both moderate and advanced technologies mean that hearing…

Research progress of free space coherent optical communication

NASA Astrophysics Data System (ADS)

Tan, Zhenkun; Ke, Xizheng

2018-02-01

This paper mainly introduces the research progress of free space coherent optical communication in Xi'an University of Technology. In recent years, the research on the outer modulation technology of the laser, free-space-to-fiber coupling technique, the design of transmitting and receiving optical antenna, adaptive optical technology with or without wave-front sensor, automatic polarization control technology, frequency stabilization technology, heterodyne detection technology and high speed signal processing technology. Based on the above related research, the digital signal modulation, transmission, detection and data recovery are realized by the heterodyne detection technology in the free space optical communication system, and finally the function of smooth viewing high-definition video is realized.

Communications and control for electric power systems

NASA Technical Reports Server (NTRS)

Kirkham, H.

1992-01-01

A long-term strategy for the integration of new control technologies for power generation and delivery is proposed: the industry would benefit from an evolutionary approach that would adapt to its needs future technologies as well as those that it has so far not heeded. The integrated operation of the entire system, including the distribution system, was proposed as a future goal. The AbNET communication protocols are reviewed, and additions that were made in 1991 are described. In the original network, traffic was controlled by polling at the master station, located at the substation, and routed by a flooding algorithm. In a revised version, the polling and flooding are modified. The question of interfacing low-energy measurement transducers or instrument transformers is considered. There is presently little or no agreement on what the output of optical current transducers (CT's) should be. Appendices deal with the calibration of current transducers; with Delta modulation, a simple means of serially encoding the output of an OCT; and with noise shaping, a method of digital signal processing that trades off the number of bits in a digital sample for a higher number of samples.

[Digital acoustic burglar alarm system using infrared radio remote control].

PubMed

Wang, Song-De; Zhao, Yan; Yao, Li-Ping; Zhang, Shuan-Ji

2009-03-01

Using butt emission infrared sensors, radio receiving and sending modules, double function integrated circuit with code and code translation, LED etc, a digital acoustic burglar alarm system using infrared radio to realize remote control was designed. It uses infrared ray invisible to eyes, composing area of radio distance. Once people and objects shelter the infrared ray, a testing signal will be output by the tester, and the sender will be triggered to work. The radio coding signal that sender sent is received by the receiver, then processed by a serial circuit. The control signal is output to trigger the sounder to give out an alarm signal, and the operator will be cued to notice this variation. At the same time, the digital display will be lighted and the alarm place will be watched. Digital coding technology is used, and a number of sub alarm circuits can joint the main receiver, so a lot of places can be monitored. The whole system features a module structure, with the property of easy alignment, stable operation, debug free and so on. The system offers an alarm range reaching 1 000 meters in all directions, and can be widely used in family, shop, storehouse, orchard and so on.

Adolescent asthma self-management: patient and parent-caregiver perspectives on using social media to improve care.

PubMed

Panzera, Anthony D; Schneider, Tali K; Martinasek, Mary P; Lindenberger, James H; Couluris, Marisa; Bryant, Carol A; McDermott, Robert J

2013-12-01

Self-management of asthma can now leverage new media technologies. To optimize implementation they must employ a consumer-oriented developmental approach. This study explored benefits of and barriers to improved asthma self-management and identified key elements for the development of a digital media tool to enhance asthma control. Between August 2010 and January 2011, 18 teens with asthma and 18 parent-caregivers participated in semistructured in-depth interviews to identify mechanisms for improving asthma self-management and propose characteristics for developing a digital media tool to aid such efforts. Teens and caregivers enumerated physician-recommended strategies for asthma management as well as currently employed strategies. Both groups thought of a potential digital media solution as positive, but indicated specific design requirements for such a solution to have utility. Whereas most participants perceived mobile platforms to be viable modes to improve asthma self-management, interest in having social networking capabilities was mixed. A digital media product capable of tracking conditions, triggers, and related asthma activities can be a core element of improved asthma control for youth. Improved asthma control will help decrease school absenteeism. © 2013, American School Health Association.

AFTI/F-111 MAW flight control system and redundancy management description

NASA Technical Reports Server (NTRS)

Larson, Richard R.

1987-01-01

The wing on the NASA F-111 transonic aircraft technology (TACT) airplane was modified to provide flexible leading and trailing edge flaps; this modified wing is known as the mission adaptive wing (MAW). A dual digital primary fly-by-wire flight control system was developed with analog backup reversion for redundancy. This report discusses the functions, design, and redundancy management of the flight control system for these flaps.

High-performance holographic technologies for fluid-dynamics experiments

PubMed Central

Orlov, Sergei S.; Abarzhi, Snezhana I.; Oh, Se Baek; Barbastathis, George; Sreenivasan, Katepalli R.

2010-01-01

Modern technologies offer new opportunities for experimentalists in a variety of research areas of fluid dynamics. Improvements are now possible in the state-of-the-art in precision, dynamic range, reproducibility, motion-control accuracy, data-acquisition rate and information capacity. These improvements are required for understanding complex turbulent flows under realistic conditions, and for allowing unambiguous comparisons to be made with new theoretical approaches and large-scale numerical simulations. One of the new technologies is high-performance digital holography. State-of-the-art motion control, electronics and optical imaging allow for the realization of turbulent flows with very high Reynolds number (more than 107) on a relatively small laboratory scale, and quantification of their properties with high space–time resolutions and bandwidth. In-line digital holographic technology can provide complete three-dimensional mapping of the flow velocity and density fields at high data rates (over 1000 frames per second) over a relatively large spatial area with high spatial (1–10 μm) and temporal (better than a few nanoseconds) resolution, and can give accurate quantitative description of the fluid flows, including those of multi-phase and unsteady conditions. This technology can be applied in a variety of problems to study fundamental properties of flow–particle interactions, rotating flows, non-canonical boundary layers and Rayleigh–Taylor mixing. Some of these examples are discussed briefly. PMID:20211881

E-inclusion Process and Societal Digital Skill Development

ERIC Educational Resources Information Center

Vitolina, Ieva

2015-01-01

Nowadays, the focus shifts from information and communication technology access to skills and knowledge. Moreover, lack of digital skills is an obstacle in the process of learning new digital competences using technologies and e-learning. The objective of this research is to investigate how to facilitate students to use the acquired digital skills…

Technical Boys and Creative Girls: The Career Aspirations of Digitally Skilled Youths

ERIC Educational Resources Information Center

Wong, Billy; Kemp, Peter E. J.

2018-01-01

Digital technology is increasingly central to our lives, particularly among young people. However, there remains a concern from government and businesses of a digital skills gap because many youths, especially girls, tend to be consumers rather than creators of technology. Drawing on 32 semi-structured interviews with digitally skilled teenagers…

Digital Media, Technologies and Scholarship: Some Shapes of eResearch in Educational Inquiry

ERIC Educational Resources Information Center

Markauskaite, Lina

2010-01-01

This paper discusses some recent developments in digital media, research technologies and scholarly practices that are known under the umbrella term of "eResearch". Drawing on conceptual ideas of digital materialism, epistemic artefacts and epistemic tools, this paper discusses how the digital inscription of knowledge and knowing could…

76 FR 70176 - Request For Information: Public Access to Digital Data Resulting from Federally Funded Scientific...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-10

... OFFICE OF SCIENCE AND TECHNOLOGY POLICY Request For Information: Public Access to Digital Data... stewardship and encouraging broad public access to unclassified digital data that result from federally funded... Science and Technology Council's Interagency Working Group on Digital Data. Release Date: November 3, 2011...

Paradox, Promise and Public Pedagogy: Implications of the Federal Government's Digital Education Revolution

ERIC Educational Resources Information Center

Buchanan, Rachel

2011-01-01

The use of digital technology in the classroom is a significant issue for teachers as they are under increasing pressure to teach in technologically mediated ways. This "digital turn" in education has culminated in the Australian federal government's Digital Education Revolution, which represents a multi-billion dollar commitment to…

Digital dentistry: information technology for today's (and tomorrow's) dental practice.

PubMed

Hirschinger, R

2001-03-01

Digital dentistry is not the wave of the future; it is occurring now. Whether a dentist embraces new technology will define his or her practice and, possibly, future. The aim of this article is to inform practitioners of the various components that constitute a digital dental practice, the technologies available today, and those on the horizon.

Teachers' Use of Digital Technology in Secondary Music Education: Illustrations of Changing Classrooms

ERIC Educational Resources Information Center

Wise, Stuart; Greenwood, Janinka; Davis, Niki

2011-01-01

The music industry in the 21st century uses digital technology in a wide range of applications including performance, composition and in recording and publishing. Much of this digital technology is freely available via downloads from the internet, as part of software included with computers when they are purchased and via applications that are…

Digital Technology at the National Science Museum of Japan

ERIC Educational Resources Information Center

Lydens, Lois; Saito, Yasuji; Inoue, Tohru

2007-01-01

The National Science Museum (NSM) in Japan has recently completed a project using different types of visitor-oriented digital technologies. With sponsorship from the Japan Society for the Promotion of Science (JSPS), the NSM team carried out a four-year study to examine how digital technologies can be used to enhance as well as educationally…

The Relationship between Digital Leadership and Digital Implementation in Elementary Schools

ERIC Educational Resources Information Center

Domeny, Jami V.

2017-01-01

New technological advances are changing the landscape for both teaching and learning at a rapid pace. With an increase in the focus and allocation of funding on technology, schools need leaders who can facilitate the change process and support a digital learning culture for technology integration. As with any focus and initiative in education, the…

Teaching in a Digital Age: How Educators Use Technology to Improve Student Learning

ERIC Educational Resources Information Center

McKnight, Katherine; O'Malley, Kimberly; Ruzic, Roxanne; Horsley, Maria Kelly; Franey, John J.; Bassett, Katherine

2016-01-01

A successful digital conversion for classrooms, districts, and states is not determined by the technology, but by how technology enables teaching and learning. The purpose of our multisite case study was to document digital instructional strategies teachers use to enhance and transform student learning, and align that use with learning research.…

Digital Technology, Schools and Teachers' Workplace Learning: Policy, Practice and Identity. Digital Education and Learning

ERIC Educational Resources Information Center

Phillips, Michael

2016-01-01

This book advances an alternative reading of the social, political and cultural issues surrounding schools and technology and develops a comprehensive overview of the interplay between policy, practice and identity in school workplaces. It explores how digital technologies have become an integral element of the politics and socially negotiated…

Digital Technology in the Tertiary Dance Technique Studio: Expanding Student Engagement through Collaborative and Co-Creative Experiences

ERIC Educational Resources Information Center

Huddy, Avril

2017-01-01

Digital technology has long been integrated into the mainstream learning environment in a variety of ways from basic teaching delivery tools to specific courseware; however, it has struggled to make an impact in the dance technique studio. Despite the enthusiastic and alacritous integration of digital technologies within the repertoire and…

Adult Learning in the Digital Age: Perspectives on Online Technologies and Outcomes

ERIC Educational Resources Information Center

Kidd, Terry T., Ed.; Keengwe, Jared, Ed.

2010-01-01

As instructors move further into the incorporation of 21st century technologies in adult education, a new paradigm of digitally-enriched mediated learning has emerged. This book provides a comprehensive framework of trends and issues related to adult learning for the facilitation of authentic learning in the age of digital technology. This…

Using Digital Technology to See Angles from Different Angles. Part 1: Corners

ERIC Educational Resources Information Center

Host, Erin; Baynham, Emily; McMaster, Heather

2014-01-01

In Part 1 of their article, Erin Host, Emily Baynham and Heather McMaster use a combination of digital technology and concrete materials to explore the concept of "corners". They provide a practical, easy to follow sequence of activities that builds on students' understandings. [For "Using Digital Technology to See Angles from…

How Digital Technologies, Blended Learning and MOOCs Will Impact the Future of Higher Education

ERIC Educational Resources Information Center

Morris, Neil P.

2014-01-01

Digital technologies are revolutionizing all parts of society, including higher education. Universities are rapidly adapting to the prevalence of staff and student mobile devices, digital tools and services on campus, and are developing strategies to harness these technologies to enhance student learning. In this paper, I explore the use of…

Organizational Influences in Technology Adoption Decisions: A Case Study of Digital Libraries

ERIC Educational Resources Information Center

Oguz, Fatih

2016-01-01

The purpose of this study was to understand the organizational level decision factors in technology adoption in the context of digital libraries. A qualitative case study approach was used to investigate the adoption of a specific technology, XML-based Web services, in digital libraries. Rogers' diffusion of innovations and Wenger's communities of…

A Survey of the University Students' Perspectives about Using Digital Technologies in Education: Zimbabwean Case

ERIC Educational Resources Information Center

Dube, Sibusisiwe; Scott, Elsje

2017-01-01

This study investigated the perspectives of university students on the use of digital technologies as tools for teaching and learning. Digital technologies are an essential asset for academic institutions as they can support strategic teaching and learning objectives for education institutions. Studies have shown that limited use of digital…

Smart Camera Technology Increases Quality

NASA Technical Reports Server (NTRS)

2004-01-01

When it comes to real-time image processing, everyone is an expert. People begin processing images at birth and rapidly learn to control their responses through the real-time processing of the human visual system. The human eye captures an enormous amount of information in the form of light images. In order to keep the brain from becoming overloaded with all the data, portions of an image are processed at a higher resolution than others, such as a traffic light changing colors. changing colors. In the same manner, image processing products strive to extract the information stored in light in the most efficient way possible. Digital cameras available today capture millions of pixels worth of information from incident light. However, at frame rates more than a few per second, existing digital interfaces are overwhelmed. All the user can do is store several frames to memory until that memory is full and then subsequent information is lost. New technology pairs existing digital interface technology with an off-the-shelf complementary metal oxide semiconductor (CMOS) imager to provide more than 500 frames per second of specialty image processing. The result is a cost-effective detection system unlike any other.

New layer-based imaging and rapid prototyping techniques for computer-aided design and manufacture of custom dental restoration.

PubMed

Lee, M-Y; Chang, C-C; Ku, Y C

2008-01-01

Fixed dental restoration by conventional methods greatly relies on the skill and experience of the dental technician. The quality and accuracy of the final product depends mostly on the technician's subjective judgment. In addition, the traditional manual operation involves many complex procedures, and is a time-consuming and labour-intensive job. Most importantly, no quantitative design and manufacturing information is preserved for future retrieval. In this paper, a new device for scanning the dental profile and reconstructing 3D digital information of a dental model based on a layer-based imaging technique, called abrasive computer tomography (ACT) was designed in-house and proposed for the design of custom dental restoration. The fixed partial dental restoration was then produced by rapid prototyping (RP) and computer numerical control (CNC) machining methods based on the ACT scanned digital information. A force feedback sculptor (FreeForm system, Sensible Technologies, Inc., Cambridge MA, USA), which comprises 3D Touch technology, was applied to modify the morphology and design of the fixed dental restoration. In addition, a comparison of conventional manual operation and digital manufacture using both RP and CNC machining technologies for fixed dental restoration production is presented. Finally, a digital custom fixed restoration manufacturing protocol integrating proposed layer-based dental profile scanning, computer-aided design, 3D force feedback feature modification and advanced fixed restoration manufacturing techniques is illustrated. The proposed method provides solid evidence that computer-aided design and manufacturing technologies may become a new avenue for custom-made fixed restoration design, analysis, and production in the 21st century.

Digital active material processing platform effort (DAMPER), SBIR phase 2

NASA Technical Reports Server (NTRS)

Blackburn, John; Smith, Dennis

1992-01-01

Applied Technology Associates, Inc., (ATA) has demonstrated that inertial actuation can be employed effectively in digital, active vibration isolation systems. Inertial actuation involves the use of momentum exchange to produce corrective forces which act directly on the payload being actively isolated. In a typical active vibration isolation system, accelerometers are used to measure the inertial motion of the payload. The signals from the accelerometers are then used to calculate the corrective forces required to counteract, or 'cancel out' the payload motion. Active vibration isolation is common technology, but the use of inertial actuation in such systems is novel, and is the focus of the DAMPER project. A May 1991 report was completed which documented the successful demonstration of inertial actuation, employed in the control of vibration in a single axis. In the 1 degree-of-freedom (1DOF) experiment a set of air bearing rails was used to suspend the payload, simulating a microgravity environment in a single horizontal axis. Digital Signal Processor (DSP) technology was used to calculate in real time, the control law between the accelerometer signals and the inertial actuators. The data obtained from this experiment verified that as much as 20 dB of rejection could be realized by this type of system. A discussion is included of recent tests performed in which vibrations were actively controlled in three axes simultaneously. In the three degree-of-freedom (3DOF) system, the air bearings were designed in such a way that the payload is free to rotate about the azimuth axis, as well as translate in the two horizontal directions. The actuator developed for the DAMPER project has applications beyond payload isolation, including structural damping and source vibration isolation. This report includes a brief discussion of these applications, as well as a commercialization plan for the actuator.

Digital active material processing platform effort (DAMPER), SBIR phase 2

NASA Astrophysics Data System (ADS)

Blackburn, John; Smith, Dennis

1992-11-01

Applied Technology Associates, Inc., (ATA) has demonstrated that inertial actuation can be employed effectively in digital, active vibration isolation systems. Inertial actuation involves the use of momentum exchange to produce corrective forces which act directly on the payload being actively isolated. In a typical active vibration isolation system, accelerometers are used to measure the inertial motion of the payload. The signals from the accelerometers are then used to calculate the corrective forces required to counteract, or 'cancel out' the payload motion. Active vibration isolation is common technology, but the use of inertial actuation in such systems is novel, and is the focus of the DAMPER project. A May 1991 report was completed which documented the successful demonstration of inertial actuation, employed in the control of vibration in a single axis. In the 1 degree-of-freedom (1DOF) experiment a set of air bearing rails was used to suspend the payload, simulating a microgravity environment in a single horizontal axis. Digital Signal Processor (DSP) technology was used to calculate in real time, the control law between the accelerometer signals and the inertial actuators. The data obtained from this experiment verified that as much as 20 dB of rejection could be realized by this type of system. A discussion is included of recent tests performed in which vibrations were actively controlled in three axes simultaneously. In the three degree-of-freedom (3DOF) system, the air bearings were designed in such a way that the payload is free to rotate about the azimuth axis, as well as translate in the two horizontal directions. The actuator developed for the DAMPER project has applications beyond payload isolation, including structural damping and source vibration isolation. This report includes a brief discussion of these applications, as well as a commercialization plan for the actuator.

Planning for optical disk technology with digital cartography.

USGS Publications Warehouse

Light, D.L.

1986-01-01

A major shortfall that still exists in digital systems is the need for very large mass storage capacity. The decade of the 1980s has introduced laser optical disk storage technology, which may be the breakthrough needed for mass storage. This paper addresses system concepts for digital cartography during the transition period. Emphasis will be placed on determining USGS mass storage requirements and introducing laser optical disk technology for handling storage problems for digital data in this decade.-from Author

An Action Research Study Investigating Children's Use of an iPad during Free Play in a Kindergarten Classroom: An Exploration of Teaching Pedagogy and Children's Learning, Social Interactions, and Digital Literacy

ERIC Educational Resources Information Center

Reynolds-Blankenship, Tara

2013-01-01

As part of human development, technology plays an important role in many children's lives. As digital technologies continue to permeate aspects of many children's everyday lives, educators are integrating digital technologies into classroom practices and, as such, have created a need to examine the ways in which children use technologies in their…

A superconducting large-angle magnetic suspension

NASA Technical Reports Server (NTRS)

Downer, James R.; Anastas, George V., Jr.; Bushko, Dariusz A.; Flynn, Frederick J.; Goldie, James H.; Gondhalekar, Vijay; Hawkey, Timothy J.; Hockney, Richard L.; Torti, Richard P.

1992-01-01

SatCon Technology Corporation has completed a Small Business Innovation Research (SBIR) Phase 2 program to develop a Superconducting Large-Angle Magnetic Suspension (LAMS) for the NASA Langley Research Center. The Superconducting LAMS was a hardware demonstration of the control technology required to develop an advanced momentum exchange effector. The Phase 2 research was directed toward the demonstration for the key technology required for the advanced concept CMG, the controller. The Phase 2 hardware consists of a superconducting solenoid ('source coils') suspended within an array of nonsuperconducting coils ('control coils'), a five-degree-of-freedom positioning sensing system, switching power amplifiers, and a digital control system. The results demonstrated the feasibility of suspending the source coil. Gimballing (pointing the axis of the source coil) was demonstrated over a limited range. With further development of the rotation sensing system, enhanced angular freedom should be possible.

A superconducting large-angle magnetic suspension

NASA Astrophysics Data System (ADS)

Downer, James R.; Anastas, George V., Jr.; Bushko, Dariusz A.; Flynn, Frederick J.; Goldie, James H.; Gondhalekar, Vijay; Hawkey, Timothy J.; Hockney, Richard L.; Torti, Richard P.

1992-12-01

SatCon Technology Corporation has completed a Small Business Innovation Research (SBIR) Phase 2 program to develop a Superconducting Large-Angle Magnetic Suspension (LAMS) for the NASA Langley Research Center. The Superconducting LAMS was a hardware demonstration of the control technology required to develop an advanced momentum exchange effector. The Phase 2 research was directed toward the demonstration for the key technology required for the advanced concept CMG, the controller. The Phase 2 hardware consists of a superconducting solenoid ('source coils') suspended within an array of nonsuperconducting coils ('control coils'), a five-degree-of-freedom positioning sensing system, switching power amplifiers, and a digital control system. The results demonstrated the feasibility of suspending the source coil. Gimballing (pointing the axis of the source coil) was demonstrated over a limited range. With further development of the rotation sensing system, enhanced angular freedom should be possible.

Autonomous Telemetry Collection for Single-Processor Small Satellites

NASA Technical Reports Server (NTRS)

Speer, Dave

2003-01-01

For the Space Technology 5 mission, which is being developed under NASA's New Millennium Program, a single spacecraft processor will be required to do on-board real-time computations and operations associated with attitude control, up-link and down-link communications, science data processing, solid-state recorder management, power switching and battery charge management, experiment data collection, health and status data collection, etc. Much of the health and status information is in analog form, and each of the analog signals must be routed to the input of an analog-to-digital converter, converted to digital form, and then stored in memory. If the micro-operations of the analog data collection process are implemented in software, the processor may use up a lot of time either waiting for the analog signal to settle, waiting for the analog-to-digital conversion to complete, or servicing a large number of high frequency interrupts. In order to off-load a very busy processor, the collection and digitization of all analog spacecraft health and status data will be done autonomously by a field-programmable gate array that can configure the analog signal chain, control the analog-to-digital converter, and store the converted data in memory.

A Pilot Study Investigating the Effects of Advanced Nuclear Power Plant Control Room Technologies: Methods and Qualitative Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

BLanc, Katya Le; Powers, David; Joe, Jeffrey

2015-08-01

Control room modernization is an important part of life extension for the existing light water reactor fleet. None of the 99 currently operating commercial nuclear power plants in the U.S. has completed a full-scale control room modernization to date. Nuclear power plant main control rooms for the existing commercial reactor fleet remain significantly analog, with only limited digital modernizations. Upgrades in the U.S. do not achieve the full potential of newer technologies that might otherwise enhance plant and operator performance. The goal of the control room upgrade benefits research is to identify previously overlooked benefits of modernization, identify candidate technologiesmore » that may facilitate such benefits, and demonstrate these technologies through human factors research. This report describes a pilot study to test upgrades to the Human Systems Simulation Laboratory at INL.« less

Steering the conversation: A linguistic exploration of natural language interactions with a digital assistant during simulated driving.

PubMed

Large, David R; Clark, Leigh; Quandt, Annie; Burnett, Gary; Skrypchuk, Lee

2017-09-01

Given the proliferation of 'intelligent' and 'socially-aware' digital assistants embodying everyday mobile technology - and the undeniable logic that utilising voice-activated controls and interfaces in cars reduces the visual and manual distraction of interacting with in-vehicle devices - it appears inevitable that next generation vehicles will be embodied by digital assistants and utilise spoken language as a method of interaction. From a design perspective, defining the language and interaction style that a digital driving assistant should adopt is contingent on the role that they play within the social fabric and context in which they are situated. We therefore conducted a qualitative, Wizard-of-Oz study to explore how drivers might interact linguistically with a natural language digital driving assistant. Twenty-five participants drove for 10 min in a medium-fidelity driving simulator while interacting with a state-of-the-art, high-functioning, conversational digital driving assistant. All exchanges were transcribed and analysed using recognised linguistic techniques, such as discourse and conversation analysis, normally reserved for interpersonal investigation. Language usage patterns demonstrate that interactions with the digital assistant were fundamentally social in nature, with participants affording the assistant equal social status and high-level cognitive processing capability. For example, participants were polite, actively controlled turn-taking during the conversation, and used back-channelling, fillers and hesitation, as they might in human communication. Furthermore, participants expected the digital assistant to understand and process complex requests mitigated with hedging words and expressions, and peppered with vague language and deictic references requiring shared contextual information and mutual understanding. Findings are presented in six themes which emerged during the analysis - formulating responses; turn-taking; back-channelling, fillers and hesitation; vague language; mitigating requests and politeness and praise. The results can be used to inform the design of future in-vehicle natural language systems, in particular to help manage the tension between designing for an engaging dialogue (important for technology acceptance) and designing for an effective dialogue (important to minimise distraction in a driving context). Copyright © 2017 Elsevier Ltd. All rights reserved.

RF control hardware design for CYCIAE-100 cyclotron

NASA Astrophysics Data System (ADS)

Yin, Zhiguo; Fu, Xiaoliang; Ji, Bin; Zhao, Zhenlu; Zhang, Tianjue; Li, Pengzhan; Wei, Junyi; Xing, Jiansheng; Wang, Chuan

2015-11-01

The Beijing Radioactive Ion-beam Facility project is being constructed by BRIF division of China Institute of Atomic Energy. In this project, a 100 MeV high intensity compact proton cyclotron is built for multiple applications. The first successful beam extraction of CYCIAE-100 cyclotron was done in the middle of 2014. The extracted proton beam energy is 100 MeV and the beam current is more than 20 μA. The RF system of the CYCIAE-100 cyclotron includes two half-wavelength cavities, two 100 kW tetrode amplifiers and power transmission line systems (all above are independent from each other) and two sets of Low Level RF control crates. Each set of LLRF control includes an amplitude control unit, a tuning control unit, a phase control unit, a local Digital Signal Process control unit and an Advanced RISC Machines based EPICS IOC unit. These two identical LLRF control crates share one common reference clock and take advantages of modern digital technologies (e.g. DSP and Direct Digital Synthesizer) to achieve closed loop voltage and phase regulations of the dee-voltage. In the beam commission, the measured dee-voltage stability of RF system is better than 0.1% and phase stability is better than 0.03°. The hardware design of the LLRF system will be reviewed in this paper.

Generation of multiple analog pulses with different duty cycles within VME control system for ICRH Aditya system

NASA Astrophysics Data System (ADS)

Joshi, Ramesh; Singh, Manoj; Jadav, H. M.; Misra, Kishor; Kulkarni, S. V.; ICRH-RF Group

2010-02-01

Ion Cyclotron Resonance Heating (ICRH) is a promising heating method for a fusion device due to its localized power deposition profile, a direct ion heating at high density, and established technology for high RF power generation and transmission at low cost. Multiple analog pulse with different duty cycle in master of digital pulse for Data acquisition and Control system for steady state RF ICRH System(RF ICRH DAC) to be used for operating of RF Generator in Aditya to produce pre ionization and second analog pulse will produce heating. The control system software is based upon single digital pulse operation for RF source. It is planned to integrate multiple analog pulses with different duty cycle in master of digital pulse for Data acquisition and Control system for RF ICRH System(RF ICRH DAC) to be used for operating of RF Generator in Aditya tokamak. The task of RF ICRH DAC is to control and acquisition of all ICRH system operation with all control loop and acquisition for post analysis of data with java based tool. For pre ionization startup as well as heating experiments using multiple RF Power of different powers and duration. The experiment based upon the idea of using single RF generator to energize antenna inside the tokamak to radiate power twise, out of which first analog pulse will produce pre ionization and second analog pulse will produce heating. The whole system is based on standard client server technology using tcp/ip protocol. DAC Software is based on linux operating system for highly reliable, secure and stable system operation in failsafe manner. Client system is based on tcl/tk like toolkit for user interface with c/c++ like environment which is reliable programming languages widely used on stand alone system operation with server as vxWorks real time operating system like environment. The paper is focused on the Data acquisition and monitoring system software on Aditya RF ICRH System with analog pulses in slave mode with digital pulse in master mode for control acquisition and monitoring and interlocking.

New Integrated Video and Graphics Technology: Digital Video Interactive.

ERIC Educational Resources Information Center

Optical Information Systems, 1987

1987-01-01

Describes digital video interactive (DVI), a new technology which combines the interactivity of the graphics capabilities in personal computers with the realism of high-quality motion video and multitrack audio in an all-digital integrated system. (MES)

Lidar In-space Technology Experiment (LITE) Electronics Overview

NASA Technical Reports Server (NTRS)

Blythe, Michael P.; Couch, Richard H.; Rowland, Carroll W.; Kitchen, Wayne L.; Regan, Curtis P.; Koch, Michael R.; Antill, Charles W.; Stevens, William T.; Rollins, Courtney H.; Kist, Edward H.

1992-01-01

The LITE electronics system consists of the following seven subsystems: Laser Transmitter Module (LTM), Boresight Assembly (BA), Aft-Optics Electronics (AOE), Digital Data Handling Unit (DDHU), Engineering Data System (EDS), Instrument Controller (IC), and the Ground Support Equipment (GSE). Each of these subsystems is discussed.

Guidance and control/ACEE

NASA Technical Reports Server (NTRS)

1981-01-01

Active controls improve airplane performance by stabilizing its flight, reducing departures from stable flight, and alleviating loads imposed by external forces such as gusts, turbulence, or maneuvers. Some uses for active control systems, the design of redundant and reliable stability augmentation systems, digital fly-by-wire, and NASA assessments of the technology of sensors and actuators are discussed. A series of trade-off studies to better define optimum flight control systems, and research by drone and full-scale models are described.

Boeing electronic flight bag

NASA Astrophysics Data System (ADS)

Trujillo, Eddie J.; Ellersick, Steven D.

2006-05-01

The Boeing Electronic Flight Bag (EFB) is a key element in the evolutionary process of an "e-enabled" flight deck. The EFB is designed to improve the overall safety, efficiency, and operation of the flight deck and corresponding airline operations by providing the flight crew with better information and enhanced functionality in a user-friendly digital format. The EFB is intended to increase the pilots' situational awareness of the airplane and systems, as well as improve the efficiency of information management. The system will replace documents and forms that are currently stored or carried onto the flight deck and put them, in digital format, at the crew's fingertips. This paper describes what the Boeing EFB is and the significant human factors and interface design issues, trade-offs, and decisions made during development of the display system. In addition, EFB formats, graphics, input control methods, challenges using COTS (commercial-off-the-shelf)-leveraged glass and formatting technology are discussed. The optical design requirements, display technology utilized, brightness control system, reflection challenge, and the resulting optical performance are presented.

Digitalized preservation and presentation of historical building - taking traditional temples and dougong as examples

NASA Astrophysics Data System (ADS)

Yang, W. B.; Yen, Y. N.; Cheng, H. M.

2015-08-01

The integration of preservation of heritage and the digital technology is an important international trend in the 21st century. The digital technology not only is able to record and preserve detailed documents and information of heritage completely, but also brings the value-added features effectively. In this study, 3D laser scanning is used to perform the digitalized archives for the interior and exterior body work of the building which contains integration of 3D scanner technology, mobile scanning collaboration and multisystem reverse modeling and integration technology. The 3D model is built by combining with multi-media presentations and reversed modeling in real scale to perform the simulation of virtual reality (VR). With interactive teaching and presentation of augmented reality to perform the interaction technology to extend the continuously update in traditional architecture information. With the upgrade of the technology and value-added in digitalization, the cultural asset value can be experienced through 3D virtual reality which makes the information presentation from the traditional reading in the past toward user operation with sensory experience and keep exploring the possibilities and development of cultural asset preservation by using digital technology makes the presentation and learning of cultural asset information toward diversification.

Where's the revolution? Digital technology and health care in the internet age.

PubMed

Miller, Edward Alan; West, Darrell M

2009-04-01

Despite the growing use of online resources, it is unclear how many Americans are using the World Wide Web for different health-related purposes and whether factors promoting use of the Internet in health care correspond with those affecting more traditional in-person and telemedicine encounters. This research uses a national public opinion survey to examine the degree to which health care consumers communicate through conventional, face-to-face consultation, telemedicine, or digital technology, and the relationship between these means of communication and respondent characteristics. Results indicate that few people are using digital technology to get information, communicate with health personnel, or make online medical purchases. Furthermore, less well educated, lower-income individuals living in rural areas tend to use the health care Internet less than others. Several policy measures need to be undertaken in order to accelerate the appropriate use of digital technology by health care consumers of all kinds. These include improving education and technological literacy and providing access to low-cost digital technology. Without a consumer complement to prevailing efforts to spur health information technology development and implementation on the part of providers, the promise of the digital revolution will continue to be limited to certain better-connected segments of the population.

The Digital Literacy Debate: An Investigation of Digital Propensity and Information and Communication Technology

ERIC Educational Resources Information Center

Nasah, Angelique; DaCosta, Boaventura; Kinsell, Carolyn; Seok, Soonhwa

2010-01-01

Research suggests students' use of information and communication technology (ICT) may be more a matter of digital literacy and access rather than a generational trait. We sought to identify ICT preferences of post-secondary students (N = 580) through a Digital Propensity Index (DPI), investigating communication methods, Internet practices and the…

Digital Photography and Journals in a Kindergarten-First-Grade Classroom: Toward Meaningful Technology Integration in Early Childhood Education

ERIC Educational Resources Information Center

Ching, Cynthia Carter; Wang, X. Christine; Shih, Mei-Li; Kedem, Yore

2006-01-01

To explore meaningful and effective technology integration in early childhood education, we investigated how kindergarten-first-grade students created and employed digital photography journals to support social and cognitive reflection. These students used a digital camera to document their daily school activities and created digital photo…

The Use of Digital Technologies across the Adult Life Span in Distance Education

ERIC Educational Resources Information Center

Jelfs, Anne; Richardson, John T. E.

2013-01-01

In June 2010, a survey was carried out to explore access to digital technology, attitudes to digital technology and approaches to studying across the adult life span in students taking courses with the UK Open University. In total, 7000 people were surveyed, of whom more than 4000 responded. Nearly all these students had access to a computer and…

Digital Tools and Challenges to Institutional Traditions of Learning: Technologies, Social Memory and the Performative Nature of Learning

ERIC Educational Resources Information Center

Saljo, R.

2010-01-01

The purpose of this article is to offer some reflections on the relationships between digital technologies and learning. It is argued that activities of learning, as they have been practised within institutionalized schooling, are coming under increasing pressure from the developments of digital technologies and the capacities to store, access and…

E-Inclusion in Early French Immersion Classrooms: Using Digital Technologies to Support Inclusive Practices that Meet the Needs of All Learners

ERIC Educational Resources Information Center

Pellerin, Martine

2013-01-01

This paper presents a 2-year collaborative action research project that investigated the use of digital technologies to support inclusive practices in Early French Immersion (EFI) classrooms. The findings reveal that the collaborative action research project contributed to empowering teachers in using digital technologies to support the…

Exploring How Digital Media Technology Can Foster Saudi EFL Students' English Language Learning

ERIC Educational Resources Information Center

Altawil, Abdulmohsin

2016-01-01

Digital media technology has become an integral part of daily life for almost all young students, and for the majority of Saudi EFL (English as a Foreign Language) students. Digital media technology may not be limited to one or two kinds; it has various types such as software and programs, devices, application, websites, social media tools, etc.…

"Happy and Excited": Perceptions of Using Digital Technology and Social Media by Young People Who Use Augmentative and Alternative Communication

ERIC Educational Resources Information Center

Hynan, Amanda; Murray, Janice; Goldbart, Juliet

2014-01-01

Young people are using digital technology and online social media within their everyday lives to enrich their social relationships. The UK government believes that using digital technology can improve social inclusion. One well-recognized outcome measure for establishing social inclusion is to examine opportunities for self-determination.…

Advanced Digital Forensic and Steganalysis Methods

DTIC Science & Technology

2009-02-01

investigation is simultaneously cropped, scaled, and processed, extending the technology when the digital image is printed, developing technology capable ...or other common processing operations). TECNOLOGY APPLICATIONS 1. Determining the origin of digital images 2. Matching an image to a camera...Technology Transfer and Innovation Partnerships Division of Research P.O. Box 6000 State University of New York Binghamton, NY 13902-6000 Phone: 607-777

PLANNING FOR OPTICAL DISK TECHNOLOGY WITH DIGITAL CARTOGRAPHY.

USGS Publications Warehouse

Light, Donald L.

1984-01-01

Progress in the computer field continues to suggest that the transition from traditional analog mapping systems to digital systems has become a practical possibility. A major shortfall that still exists in digital systems is the need for very large mass storage capacity. The decade of the 1980's has introduced laser optical disk storage technology, which may be the breakthrough needed for mass storage. This paper addresses system concepts for digital cartography during the transition period. Emphasis is placed on determining U. S. Geological Survey mass storage requirements and introducing laser optical disk technology for handling storage problems for digital data in this decade.

Digital Natives as Preservice Teachers: What Technology Preparation Is Needed?

ERIC Educational Resources Information Center

Lei, Jing

2009-01-01

This study focused on "digital natives" as preservice teachers to examine their beliefs, attitudes, and technology experiences and expertise, identify the strengths and weaknesses in their technology knowledge and skills, and explore what technology preparation was needed to prepare them to integrate technology in their future classrooms. Results…

The Development of Micromachined Gyroscope Structure and Circuitry Technology

PubMed Central

Xia, Dunzhu; Yu, Cheng; Kong, Lun

2014-01-01

This review surveys micromachined gyroscope structure and circuitry technology. The principle of micromachined gyroscopes is first introduced. Then, different kinds of MEMS gyroscope structures, materials and fabrication technologies are illustrated. Micromachined gyroscopes are mainly categorized into micromachined vibrating gyroscopes (MVGs), piezoelectric vibrating gyroscopes (PVGs), surface acoustic wave (SAW) gyroscopes, bulk acoustic wave (BAW) gyroscopes, micromachined electrostatically suspended gyroscopes (MESGs), magnetically suspended gyroscopes (MSGs), micro fiber optic gyroscopes (MFOGs), micro fluid gyroscopes (MFGs), micro atom gyroscopes (MAGs), and special micromachined gyroscopes. Next, the control electronics of micromachined gyroscopes are analyzed. The control circuits are categorized into typical circuitry and special circuitry technologies. The typical circuitry technologies include typical analog circuitry and digital circuitry, while the special circuitry consists of sigma delta, mode matching, temperature/quadrature compensation and novel special technologies. Finally, the characteristics of various typical gyroscopes and their development tendency are discussed and investigated in detail. PMID:24424468

[THE VIRTUAL CYTOLOGIC SLIDES FOR EXTERNAL EVALUATION OF QUALITY OF IMPLEMENTATION OF CYTOLOGIC ANALYSES IN CLINICAL DIAGNOSTIC LABORATORIES: POSSIBILITIES AND PERSPECTIVES].

PubMed

Djangirova, T V; Shabalova, I P; Pronichev, A N; Polyakov, E V

2015-08-01

The article considers application of technology of analysis of cytological slides in external quality control of clinical diagnostic laboratories. The advantages of virtual slides are demonstrated against other applied technologies of external evaluation of quality i.e. slide plate and digital micro-photography. The conditions of formation of virtual slides for external evaluation of quality of clinical diagnostic laboratories. The technology of their application is described. The success of practical application of considered technology in the Federal system of external evaluation of quality is emphasized.

Factors related to the implementation and diffusion of new technologies: a pilot study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-06-01

In order to develop an understanding of how government intervention affects the processes of implementation and diffusion of new technologies, case studies of 14 technologies were carried out: automobiles; broadcast radio; frozen foods; black and white TV; color TV; polio vaccine; supersonic transport; fluoridation of water supplies; computer-aided instruction; basic oxygen process for steel; numerical control in manufacturing; digital computers; lasers; and integrated circuit. The key factors, their motivations for implementing/adopting the technology (or not doing so), the interactions among the key factors, and how these affected implementation/adoption are examined.

Online, offline, realtime: recent developments in industrial photogrammetry

NASA Astrophysics Data System (ADS)

Boesemann, Werner

2003-01-01

In recent years industrial photogrammetry has emerged from a highly specialized niche technology to a well established tool in industrial coordinate measurement applications with numerous installations in a significantly growing market of flexible and portable optical measurement systems. This is due to the development of powerful, but affordable video and computer technology. The increasing industrial requirements for accuracy, speed, robustness and ease of use of these systems together with a demand for the highest possible degree of automation have forced universities and system manufacturer to develop hard- and software solutions to meet these requirements. The presentation will show the latest trends in hardware development, especially new generation digital and/or intelligent cameras, aspects of image engineering like use of controlled illumination or projection technologies, and algorithmic and software aspects like automation strategies or new camera models. The basic qualities of digital photogrammetry- like portability and flexibility on one hand and fully automated quality control on the other - sometimes lead to certain conflicts in the design of measurement systems for different online, offline, or real-time solutions. The presentation will further show, how these tools and methods are combined in different configurations to be able to cover the still growing demands of the industrial end-users.

Photogrammetry in the line: recent developments in industrial photogrammetry

NASA Astrophysics Data System (ADS)

Boesemann, Werner

2003-05-01

In recent years industrial photogrammetry has emerged from a highly specialized niche technology to a well established tool in industrial coordinate measurement applications with numerous installations in a significantly growing market of flexible and portable optical measurement systems. This is due to the development of powerful, but affordable video and computer technology. The increasing industrial requirements for accuracy, speed, robustness and ease of use of these systems together with a demand for the highest possible degree of automation have forced universities and system manufacturers to develop hard- and software solutions to meet these requirements. The presentation will show the latest trends in hardware development, especially new generation digital and/or intelligent cameras, aspects of image engineering like use of controlled illumination or projection technologies,and algorithmic and software aspects like automation strategies or new camera models. The basic qualities of digital photogrammetry-like portability and flexibility on one hand and fully automated quality control on the other -- sometimes lead to certain conflicts in the design of measurement systems for different online, offline or real-time solutions. The presentation will further show, how these tools and methods are combined in different configurations to be able to cover the still growing demands of the industrial end-users.

ODIN system technology module library, 1972 - 1973

NASA Technical Reports Server (NTRS)

Hague, D. S.; Watson, D. A.; Glatt, C. R.; Jones, R. T.; Galipeau, J.; Phoa, Y. T.; White, R. J.

1978-01-01

ODIN/RLV is a digital computing system for the synthesis and optimization of reusable launch vehicle preliminary designs. The system consists of a library of technology modules in the form of independent computer programs and an executive program, ODINEX, which operates on the technology modules. The technology module library contains programs for estimating all major military flight vehicle system characteristics, for example, geometry, aerodynamics, economics, propulsion, inertia and volumetric properties, trajectories and missions, steady state aeroelasticity and flutter, and stability and control. A general system optimization module, a computer graphics module, and a program precompiler are available as user aids in the ODIN/RLV program technology module library.

Digital Learning Resources and Ubiquitous Technologies in Education

ERIC Educational Resources Information Center

Camilleri, Mark Anthony; Camilleri, Adriana Caterina

2017-01-01

This research explores the educators' attitudes and perceptions about their utilisation of digital learning technologies. The methodology integrates measures from "the pace of technological innovativeness" and the "technology acceptance model" to understand the rationale for further ICT investment in compulsory education. A…

Thermostatic system of sensor in NIR spectrometer based on PID control

NASA Astrophysics Data System (ADS)

Wang, Zhihong; Qiao, Liwei; Ji, Xufei

2016-11-01

Aiming at the shortcomings of the primary sensor thermostatic control system in the near infrared (NIR) spectrometer, a novel thermostatic control system based on proportional-integral-derivative (PID) control technology was developed to improve the detection precision of the NIR spectrometer. There were five parts including bridge amplifier circuit, analog-digital conversion (ADC) circuit, microcontroller, digital-analog conversion (DAC) circuit and drive circuit in the system. The five parts formed a closed-loop control system based on PID algorithm that was used to control the error between the temperature calculated by the sampling data of ADC and the designed temperature to ensure the stability of the spectrometer's sensor. The experimental results show that, when the operating temperature of sensor is -11°, compared with the original system, the temperature control precision of the new control system is improved from ±0.64° to ±0.04° and the spectrum signal to noise ratio (SNR) is improved from 4891 to 5967.

WE-D-BRD-01: Innovation in Radiation Therapy Delivery: Advanced Digital Linac Features

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xing, L; Wong, J; Li, R

2014-06-15

Last few years has witnessed significant advances in linac technology and therapeutic dose delivery method. Digital linacs equipped with high dose rate FFF beams have been clinically implemented in a number of hospitals. Gated VMAT is becoming increasingly popular in treating tumors affected by respiratory motion. This session is devoted to update the audience with these technical advances and to present our experience in clinically implementing the new linacs and dose delivery methods. Topics to be covered include, technical features of new generation of linacs from different vendors, dosimetric characteristics and clinical need for FFF-beam based IMRT and VMAT, respiration-gatedmore » VMAT, the concept and implementation of station parameter optimized radiation therapy (SPORT), beam level imaging and onboard image guidance tools. Emphasis will be on providing fundamental understanding of the new treatment delivery and image guidance strategies, control systems, and the associated dosimetric characteristics. Commissioning and acceptance experience on these new treatment delivery technologies will be reported. Clinical experience and challenges encountered during the process of implementation of the new treatment techniques and future applications of the systems will also be highlighted. Learning Objectives: Present background knowledge of emerging digital linacs and summarize their key geometric and dosimetric features. SPORT as an emerging radiation therapy modality specifically designed to take advantage of digital linacs. Discuss issues related to the acceptance and commissioning of the digital linacs and FFF beams. Describe clinical utility of the new generation of digital linacs and their future applications.« less

GMA200 ATEGG Digital Controls Demonstration.

DTIC Science & Technology

1979-10-01

report has been reviewed by the Office of Public Affairs (ASD/PA) and is releasable to the National Technical Information Service (NTIS). At NTIS, it...Conrolling Ofice) 5. SECU.R1Y C..ASS. or this report)1<, // . Unclassified S.. OEC . ASSIgiCATION 0OWNGRACtNG SCHEDULE 6, OISTRIBUTION STATEMENT cit...controller on Build 5 of the Advanced Technology Engine Gas Generator (ATEGG) . Control modes are described with emphasis on changes to he incorporated on

Digital Avionics

NASA Technical Reports Server (NTRS)

Koelbl, Terry G.; Ponchak, Denise; Lamarche, Teresa

2002-01-01

The field of digital avionics experienced another year of important advances in civil aviation, military systems, and space applications. As a result of the events of 9/11/2001, NASA has pursued activities to apply its aerospace technologies toward improved aviation security. Both NASA Glenn Research Center and Langley Research Center have performed flight research demonstrations using advanced datalink concepts to transmit live pictures from inside a jetliner, and to downlink the contents of the plane's 'black box' recorder in real time. The U.S. Navy and General Electric demonstrated survivable engine control (SEC) algorithms during engine ground tests at the Weapons Survivability Laboratory at China Lake. The scientists at Boeing Satellite Systems advanced the field of stellar inertial technology with the development of a new method for positioning optical star trackers on satellites.

Data acquisition and analysis in the DOE/NASA Wind Energy Program

NASA Technical Reports Server (NTRS)

Neustadter, H. E.

1980-01-01

Four categories of data systems, each responding to a distinct information need are presented. The categories are: control, technology, engineering and performance. The focus is on the technology data system which consists of the following elements: sensors which measure critical parameters such as wind speed and direction, output power, blade loads and strains, and tower vibrations; remote multiplexing units (RMU) mounted on each wind turbine which frequency modulate, multiplex and transmit sensor outputs; the instrumentation available to record, process and display these signals; and centralized computer analysis of data. The RMU characteristics and multiplexing techniques are presented. Data processing is illustrated by following a typical signal through instruments such as the analog tape recorder, analog to digital converter, data compressor, digital tape recorder, video (CRT) display, and strip chart recorder.

Quiet Clean Short-Haul Experimental Engine (QCSEE) Under-the-Wing (UTW) Final Design Report

NASA Technical Reports Server (NTRS)

1977-01-01

The QCSEE Program provides for the design, fabrication, and testing of two experimental high-bypass geared turbofan engines and propulsion systems for short-haul passenger aircraft. The overall objective of the program is to develop the propulsion technology required for future externally blown flap types of aircraft with engines located both under-the-wing and over-the-wing. This technology includes work in composite structures and digital engine controls.

On the Brain Basis of Digital Daze in Millennial Minds: Rejoinder to "Digital Technology and Student Cognitive Development: The Neuroscience of the University Classroom"

ERIC Educational Resources Information Center

Brown, Timothy T.

2016-01-01

In this issue, Cavanaugh, Giapponi, and Golden (2016) have discussed the new prominent role of digital devices in the lives of students; the possible impact of these widely-used technologies on developing, learning minds; and the relevance of new cognitive neuroscience research and technologies for better understanding the potential effects of…

Rethinking Education in the Age of Technology: The Digital Revolution and Schooling in America. Technology, Education--Connections (TEC) Series

ERIC Educational Resources Information Center

Collins, Allan; Halverson, Richard

2009-01-01

The digital revolution has hit education, with more and more classrooms plugged into the whole wired world. But are schools making the most of new technologies? Are they tapping into the learning potential of today's Firefox/Facebook/cell phone generation? Have schools fallen through the crack of the digital divide? In "Rethinking Education in the…

Digital Sensor Technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, Ken D.; Quinn, Edward L.; Mauck, Jerry L.

The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy and reliability. This paper, which refers to a final report issued in 2013, demonstrates these benefits in direct comparisons of digital and analog sensor applications. Improved accuracy results from the superior operating characteristics of digital sensors. These include improvements in sensor accuracy and drift and other related parameters which reduce total loop uncertainty and thereby increase safety and operating margins. Anmore » example instrument loop uncertainty calculation for a pressure sensor application is presented to illustrate these improvements. This is a side-by-side comparison of the instrument loop uncertainty for both an analog and a digital sensor in the same pressure measurement application. Similarly, improved sensor reliability is illustrated with a sample calculation for determining the probability of failure on demand, an industry standard reliability measure. This looks at equivalent analog and digital temperature sensors to draw the comparison. The results confirm substantial reliability improvement with the digital sensor, due in large part to ability to continuously monitor the health of a digital sensor such that problems can be immediately identified and corrected. This greatly reduces the likelihood of a latent failure condition of the sensor at the time of a design basis event. Notwithstanding the benefits of digital sensors, there are certain qualification issues that are inherent with digital technology and these are described in the report. One major qualification impediment for digital sensor implementation is software common cause failure (SCCF).« less

Digital microscopy. Bringing new technology into focus.

PubMed

2010-06-01

Digital microscopy enables the scanning of microscope slides so that they can be viewed, analyzed, and archived on a computer. While the technology is not yet widely accepted by pathologists, a switch to digital microscopy systems seems to be inevitable in the near future.

The Integrity of Digital Information: Mechanics and Definitional Issues.

ERIC Educational Resources Information Center

Lynch, Clifford A.

1994-01-01

Considers issues regarding the migration of a system of literature into electronic formats. Highlights include integrity in an information distribution system; digest technology; tracings that permit detection of copied digital objects; verifying sources; digital signature technology and cryptography; electronic publishing; and intellectual…

Digital Image Access & Retrieval.

ERIC Educational Resources Information Center

Heidorn, P. Bryan, Ed.; Sandore, Beth, Ed.

Recent technological advances in computing and digital imaging technology have had immediate and permanent consequences for visual resource collections. Libraries are involved in organizing and managing large visual resource collections. The central challenges in working with digital image collections mirror those that libraries have sought to…

An Ethics Whirlwind: A Perspective of the Digital Lifestyle of Digital Natives and Initial Thoughts on Ethics Education in Technology

ERIC Educational Resources Information Center

Hall, Brian R.

2012-01-01

As digital natives continue rolling onto college campuses around the country, the questions surrounding digital ethics grow. Students do not know life without modern technology, computers, mobile devices, the Internet and their lifestyle has developed around this mass. Unlike their predecessors, they do not recognize a difference between the…

Using Disruptive Technologies to Make Digital Connections: Stories of Media Use and Digital Literacy in Secondary Classrooms

ERIC Educational Resources Information Center

Nowell, Shanedra D.

2014-01-01

This study focused on ways teachers and students in an urban high school used technologies often labeled as disruptive (i.e. social media and mobile phones) as learning and relationship building tools, inside and outside the classroom. In this teacher research study, secondary teachers discussed digital literacies, the digital divide, and digital…

Digital Native Preservice Teachers: An Examination of Their Self-Efficacy Beliefs Regarding Technology Integration in Classroom Settings

ERIC Educational Resources Information Center

Southall, Sarah Parker

2012-01-01

The purpose of this mixed-method study was to investigate digital native preservice teachers' self-efficacy beliefs regarding their technology experiences and skills at the beginning and at the end of their field placement semester. Digital natives, as defined by Prensky (2001), are students born after 1980 who have been raised with digital media…

Reproducible Operating Margins on a 72800-Device Digital Superconducting Chip (Open Access)

DTIC Science & Technology

2015-10-28

superconductor digital logic. Keywords: flux trapping, yield, digital Superconductor digital technology offers fundamental advantages over conventional...trapping in the superconductor films can degrade or preclude correct circuit operation. Scaling superconductor technology is now possible due to recent...advances in circuit design embodied in reciprocal quantum logic (RQL) [2, 3] and recent advances in superconductor integrated circuit fabrication, which

Exploring Professional Development Needs of Digital Immigrant and Digital Native Teachers for the Successful Integration of Technology in a Jewish Elementary Education Setting

ERIC Educational Resources Information Center

Salomon, Anna M.

2014-01-01

Today's teachers are tasked with the integration of technology in their curriculum and their classrooms. In order to do that, teachers require professional development/training and support. Further, schools are encountering a unique landscape of teaching with digital natives becoming teachers alongside digital immigrants. This study aimed to…

The Digital Skills Paradox: How Do Digitally Excluded Youth Develop Skills to Use the Internet?

ERIC Educational Resources Information Center

Eynon, Rebecca; Geniets, Anne

2016-01-01

Digital skills are an important aspect of ensuring that all young people are digitally included. Yet, there tends to be an assumption in popular discourse that young people can simply learn these skills by themselves. While experience of technologies forms an important part of the learning process, other resources (i.e., access to technology and…

The Digitally Disadvantaged: Access to Digital Communication Technologies among First Year Students at a Rural South African University

ERIC Educational Resources Information Center

Oyedemi, Toks; Mogano, Saki

2018-01-01

Considering the importance of digital skills in university education, this article reports on a study which examined access to technology among first year students at a rural South African university. The study focused on the digital readiness of students prior to their admission to the university, since many universities provide access to…

Pre-Service Teachers in Second Life: Are Digital Natives Prepared for a Web 2.0 Experience?

ERIC Educational Resources Information Center

Inman, Christopher T.

2010-01-01

Today's college students, "digital natives," have had digital technology at their fingertips (Rushkoff, 1996; Prensky, 2001a). Technology habits and expectations of young people are changing; the educational and business worlds have placed a focus on skills called "21st century skills," to prepare students for the digital age (Lemke, 2002). Skills…

State-of-the-art cockpit design for the HH-65A helicopters

NASA Technical Reports Server (NTRS)

Castleberry, D. E.; Mcelreath, M. Y.

1982-01-01

In the design of a HH-65A helicopter cockpit, advanced integrated electronics systems technology was employed to achieve several important goals for this multimission aircraft. They were: (1) integrated systems operation with consistent and simplified cockpit procedures; (2) mission-task-related cockpit displays and controls, and (3) reduced pilot instrument scan effort with excellent outside visibility. The integrated avionics system was implemented to depend heavily upon distributed but complementary processing, multiplex digital bus technology, and multifunction CRT controls and displays. This avionics system was completely flight tested and will soon enter operational service with the Coast Guard.

"What Goes Around Comes Around": Lessons Learned from Economic Evaluations of Personalized Medicine Applied to Digital Medicine.

PubMed

Phillips, Kathryn A; Douglas, Michael P; Trosman, Julia R; Marshall, Deborah A

2017-01-01

The growth of "big data" and the emphasis on patient-centered health care have led to the increasing use of two key technologies: personalized medicine and digital medicine. For these technologies to move into mainstream health care and be reimbursed by insurers, it will be essential to have evidence that their benefits provide reasonable value relative to their costs. These technologies, however, have complex characteristics that present challenges to the assessment of their economic value. Previous studies have identified the challenges for personalized medicine and thus this work informs the more nascent topic of digital medicine. To examine the methodological challenges and future opportunities for assessing the economic value of digital medicine, using personalized medicine as a comparison. We focused specifically on digital biomarker technologies and multigene tests. We identified similarities in these technologies that can present challenges to economic evaluation: multiple results, results with different types of utilities, secondary findings, downstream impact (including on family members), and interactive effects. Using a structured review, we found that there are few economic evaluations of digital biomarker technologies, with limited results. We conclude that more evidence on the effectiveness of digital medicine will be needed but that the experiences with personalized medicine can inform what data will be needed and how such analyses can be conducted. Our study points out the critical need for typologies and terminology for digital medicine technologies that would enable them to be classified in ways that will facilitate research on their effectiveness and value. Copyright © 2017 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Digital Learning As Enhanced Learning Processing? Cognitive Evidence for New insight of Smart Learning.

PubMed

Di Giacomo, Dina; Ranieri, Jessica; Lacasa, Pilar

2017-01-01

Large use of technology improved quality of life across aging and favoring the development of digital skills. Digital skills can be considered an enhancing to human cognitive activities. New research trend is about the impact of the technology in the elaboration information processing of the children. We wanted to analyze the influence of technology in early age evaluating the impact on cognition. We investigated the performance of a sample composed of n. 191 children in school age distributed in two groups as users: high digital users and low digital users. We measured the verbal and visuoperceptual cognitive performance of children by n. 8 standardized psychological tests and ad hoc self-report questionnaire. Results have evidenced the influence of digital exposition on cognitive development: the cognitive performance is looked enhanced and better developed: high digital users performed better in naming, semantic, visual memory and logical reasoning tasks. Our finding confirms the data present in literature and suggests the strong impact of the technology using not only in the social, educational and quality of life of the people, but also it outlines the functionality and the effect of the digital exposition in early age; increased cognitive abilities of the children tailor digital skilled generation with enhanced cognitive processing toward to smart learning.

Museum Informatics.

ERIC Educational Resources Information Center

Marty, Paul F.; Rayward, W. Boyd; Twidale, Michael B.

2003-01-01

Discusses museum informatics that studies how information science and technology affect the museum environment. Examines digital technology; information organization and access; digitization, personal computers, and the Internet; data sharing; standards; social impacts of new technologies; collaboration; consortia; multimedia exhibits; virtual…

Acoustic charge transport technology investigation for advanced development transponder

NASA Technical Reports Server (NTRS)

Kayalar, S.

1993-01-01

Acoustic charge transport (ACT) technology has provided a basis for a new family of analog signal processors, including a programmable transversal filter (PTF). Through monolithic integration of ACT delay lines with GaAs metal semiconductor field effect transistor (MESFET) digital memory and controllers, these devices significantly extend the performance of PTF's. This article introduces the basic operation of these devices and summarizes their present and future specifications. The production and testing of these devices indicate that this new technology is a promising one for future space applications.

Demonstration of three gorges archaeological relics based on 3D-visualization technology

NASA Astrophysics Data System (ADS)

Xu, Wenli

2015-12-01

This paper mainly focuses on the digital demonstration of three gorges archeological relics to exhibit the achievements of the protective measures. A novel and effective method based on 3D-visualization technology, which includes large-scaled landscape reconstruction, virtual studio, and virtual panoramic roaming, etc, is proposed to create a digitized interactive demonstration system. The method contains three stages: pre-processing, 3D modeling and integration. Firstly, abundant archaeological information is classified according to its history and geographical information. Secondly, build up a 3D-model library with the technology of digital images processing and 3D modeling. Thirdly, use virtual reality technology to display the archaeological scenes and cultural relics vividly and realistically. The present work promotes the application of virtual reality to digital projects and enriches the content of digital archaeology.

The contributions of digital technologies in the teaching of nursing skills: an integrative review.

PubMed

Silveira, Maurício de Souza; Cogo, Ana Luísa Petersen

2017-07-13

To analyze the contributions of digital educational technologies used in teaching nursing skills. Integrative literature review, search in five databases, from 2006 to 2015 combining the descriptors 'education, nursing', 'educational technology', 'computer-assisted instruction' or related terms in English. Sample of 30 articles grouped in the thematic categories 'technology in the simulation with manikin', 'incentive to learning' and 'teaching of nursing skills'. It was identified different formats of digital educational technologies used in teaching Nursing skills such as videos, learning management system, applications, hypertext, games, virtual reality simulators. These digital materials collaborated in the acquisition of theoretical references that subsidize the practices, enhancing the teaching and enable the use of active learning methods, breaking with the traditional teaching of demonstrating and repeating procedures.

Using Digital Health Technology to Better Generate Evidence and Deliver Evidence-Based Care.

PubMed

Sharma, Abhinav; Harrington, Robert A; McClellan, Mark B; Turakhia, Mintu P; Eapen, Zubin J; Steinhubl, Steven; Mault, James R; Majmudar, Maulik D; Roessig, Lothar; Chandross, Karen J; Green, Eric M; Patel, Bakul; Hamer, Andrew; Olgin, Jeffrey; Rumsfeld, John S; Roe, Matthew T; Peterson, Eric D

2018-06-12

As we enter the information age of health care, digital health technologies offer significant opportunities to optimize both clinical care delivery and clinical research. Despite their potential, the use of such information technologies in clinical care and research faces major data quality, privacy, and regulatory concerns. In hopes of addressing both the promise and challenges facing digital health technologies in the transformation of health care, we convened a think tank meeting with academic, industry, and regulatory representatives in December 2016 in Washington, DC. In this paper, we summarize the proceedings of the think tank meeting and aim to delineate a framework for appropriately using digital health technologies in healthcare delivery and research. Copyright © 2018 American College of Cardiology Foundation. All rights reserved.

Shaping Our World: Digital Storytelling and the Authoring of Society

ERIC Educational Resources Information Center

Brzoska, Karen Lynn

2009-01-01

Globalization, networked societies, and a knowledge-based economy engender increasing reliance on digital communication technologies for the dissemination of information and ideas (Castells, Fernandez-Ardevol, Qiu & Sey, 2006). While the technological revolution has broadened access this digital domain, participants often adopt the passive…

Learning Reconsidered: Education in the Digital Age. Communications, Convergence and the Curriculum.

ERIC Educational Resources Information Center

Dennis, Everette E.; Meyer, Philip; Sundar, S. Shyam; Pryor, Larry; Rogers, Everett M.; Chen, Helen L.; Pavlik, John

2003-01-01

Includes thoughts of seven educators on the place of digital communication in journalism and mass communication education. Discusses communication scholars and the professional field's readiness for the digital age. Notes educators' attitudes towards technology and technology's applications in education. (PM)

Digital Readiness Gaps

ERIC Educational Resources Information Center

Horrigan, John B.

2016-01-01

For many years concerns about "digital divides" centered primarily on whether people had "access" to digital technologies. Now, those worried about these issues also focus on the degree to which people succeed or struggle when they use technology to try to navigate their environments, solve problems, and make decisions. This…

Training Psychiatry Residents in Professionalism in the Digital World.

PubMed

John, Nadyah Janine; Shelton, P G; Lang, Michael C; Ingersoll, Jennifer

2017-06-01

Professionalism is an abstract concept which makes it difficult to define, assess and teach. An additional layer of complexity is added when discussing professionalism in the context of digital technology, the internet and social media - the digital world. Current physicians-in-training (residents and fellows) are digital natives having been raised in a digital, media saturated world. Consequently, their use of digital technology and social media has been unconstrained - a reflection of it being integral to their social construct and identity. Cultivating the professional identity and therefore professionalism is the charge of residency training programs. Residents have shown negative and hostile attitudes to formalized professionalism curricula in training. Approaches to these curricula need to consider the learning style of Millennials and incorporate more active learning techniques that utilize technology. Reviewing landmark position papers, guidelines and scholarly work can therefore be augmented with use of vignettes and technology that are available to residency training programs for use with their Millennial learners.

Technology and Reform-Based Science Education

ERIC Educational Resources Information Center

Dani, Danielle E.; Koenig, Kathleen M.

2008-01-01

Current reforms in science education call for the integration of digital technologies into science teaching, advocating that students learn science content and processes through technology. In this article, we provide practical examples, situated within the literature, of how digital technologies can be used to support the development and…

Using digital technologies to engage with medical research: views of myotonic dystrophy patients in Japan.

PubMed

Coathup, Victoria; Teare, Harriet J A; Minari, Jusaku; Yoshizawa, Go; Kaye, Jane; Takahashi, Masanori P; Kato, Kazuto

2016-08-24

As in other countries, the traditional doctor-patient relationship in the Japanese healthcare system has often been characterised as being of a paternalistic nature. However, in recent years there has been a gradual shift towards a more participatory-patient model in Japan. With advances in technology, the possibility to use digital technologies to improve patient interactions is growing and is in line with changing attitudes in the medical profession and society within Japan and elsewhere. The implementation of an online patient engagement platform is being considered by the Myotonic Dystrophy Registry of Japan. The aim of this exploratory study was to understand patients' views and attitudes to using digital tools in patient registries and engagement with medical research in Japan, prior to implementation of the digital platform. We conducted an exploratory, cross-sectional, self-completed questionnaire with a sample of myotonic dystrophy (MD) patients attending an Open Day at Osaka University, Japan. Patients were eligible for inclusion if they were 18 years or older, and were diagnosed with MD. A total of 68 patients and family members attended the Open Day and were invited to participate in the survey. Of those, 59 % submitted a completed questionnaire (n = 40). The survey showed that the majority of patients felt that they were not receiving the information they wanted from their clinicians, which included recent medical research findings and opportunities to participate in clinical trials, and 88 % of patients indicated they would be willing to engage with digital technologies to receive relevant medical information. Patients also expressed an interest in having control over when and how they received this information, as well as being informed of how their data is used and shared with other researchers. Overall, the findings from this study suggest that there is scope to develop a digital platform to engage with patients so that they can receive information about medical care and research opportunities. While this study group is a small, self-selecting population, who suffer from a particular condition, the results suggest that there are interested populations within Japan that would appreciate enhanced communication and interaction with healthcare teams.

Laying the foundation for a digital Nova Scotia

NASA Astrophysics Data System (ADS)

Bond, J.

2016-04-01

In 2013, the Province of Nova Scotia began an effort to modernize its coordinate referencing infrastructure known as the Nova Scotia Coordinate Referencing System (NSCRS). At that time, 8, active GPS stations were installed in southwest Nova Scotia to evaluate the technology's ability to address the Province's coordinate referencing needs. The success of the test phase helped build a business case to implement the technology across the entire Province. It is anticipated that by the end of 2015, 40 active GPS stations will be in place across Nova Scotia. This infrastructure, known as the Nova Scotia Active Control Stations (NSACS) network, will allow for instantaneous, centimetre level positioning across the Province. Originally designed to address the needs of the surveying community, the technology has also proven to have applications in mapping, machine automation, agriculture, navigation, emergency response, earthquake detection and other areas. In the foreseeable future, all spatial data sets captured in Nova Scotia will be either directly or indirectly derived from the NSACS network. The technology will promote high accuracy and homogenous spatial data sets across the Province. The technology behind the NSACS and the development of the system are described. Examples of how the technology is contributing to a digital Nova Scotia are presented. Future applications of the technology are also considered.

Acceptance Testing of a Satellite SCADA Photovoltaic-Diesel Hybrid System

NASA Technical Reports Server (NTRS)

Kalu, Alex; Acosta, R.; Durand, S.; Emrich, Carol; Ventre, G.; Wilson, W.

1999-01-01

Savannah State University (SSU) and the Florida Solar Energy Center (FSEC) have been participating in the NASA Advanced Communications Technology Satellite (ACTS) program for the last five years. This program was designed by NASA to help maintain U.S. leadership in commercial space communications by funding high-risk research, and to flight-test next-generation digital satellite components. Launched in 1993, ACTS is an U.S. government funded technology test-bed that incorporates high power Ka-band transponders, small spot beams, and on-board digital storage and switching technology. Associated with the spacecraft, is a prototype satellite control center that supports various application experiments. The SSU/FSEC application experiment is to developing a Photovoltaic-Diesel Hybrid Power system complete with satellite Supervisory Control and Data Acquisition (SCADA). The hybrid system was design to demonstrate the feasibility of using SCADA to maintain and operate remote village power systems. This configuration would enable experts at a central location to provide technical assistance to local technicians while they acquire a measure of proficiency with the hybrid system operation and maintenance. Upon full mastery of the technology, similar SCADA arrangement are planned to remotely monitor and control constellation of hybrid systems scattered overlarge rural areas. Two Orion Energy APEX-1000 hybrid systems were delivered in 1998, one was installed at SSU in eastern Georgia and the other was installed at FSEC in Central Florida. The project was designed to: (1) evaluate the performance of ACTS in a SCADA arrangement, (2) monitor the health and performance of all major hybrid subsystems, (3) investigate load control and battery charging strategies to maximize battery capacity and lifetime, and (4) develop satellite communication protocol. Preliminary results indicate that the hybrid design is suitable for satellite Supervisory Control and Data Acquisition. A modification to the controller software has produced a robust communication link capable of real time control and long term data collection.

Application of Virtual and Augmented reality to geoscientific teaching and research.

NASA Astrophysics Data System (ADS)

Hodgetts, David

2017-04-01

The geological sciences are the ideal candidate for the application of Virtual Reality (VR) and Augmented Reality (AR). Digital data collection techniques such as laser scanning, digital photogrammetry and the increasing use of Unmanned Aerial Vehicles (UAV) or Small Unmanned Aircraft (SUA) technology allow us to collect large datasets efficiently and evermore affordably. This linked with the recent resurgence in VR and AR technologies make these 3D digital datasets even more valuable. These advances in VR and AR have been further supported by rapid improvements in graphics card technologies, and by development of high performance software applications to support them. Visualising data in VR is more complex than normal 3D rendering, consideration needs to be given to latency, frame-rate and the comfort of the viewer to enable reasonably long immersion time. Each frame has to be rendered from 2 viewpoints (one for each eye) requiring twice the rendering than for normal monoscopic views. Any unnatural effects (e.g. incorrect lighting) can lead to an uncomfortable VR experience so these have to be minimised. With large digital outcrop datasets comprising 10's-100's of millions of triangles this is challenging but achievable. Apart from the obvious "wow factor" of VR there are some serious applications. It is often the case that users of digital outcrop data do not appreciate the size of features they are dealing with. This is not the case when using correctly scaled VR, and a true sense of scale can be achieved. In addition VR provides an excellent way of performing quality control on 3D models and interpretations and errors are much more easily visible. VR models can then be used to create content that can then be used in AR applications closing the loop and taking interpretations back into the field.

Digital Disconnect or Digital Difference? A Socio-Ecological Perspective on Young Children's Technology Use in the Home and the Early Childhood Centre

ERIC Educational Resources Information Center

Edwards, Susan; Henderson, Michael; Gronn, Donna; Scott, Anne; Mirkhil, Moska

2017-01-01

A digital disconnect perspective is founded on an assumption that technology use in the home is frequent, creative and generative, and that technology use in the early childhood centre should be the same as that found in the home. However, such arguments divert our attention from understanding the nature of the setting and thereby from an…

Digital Narrative and the Humanities: An Evaluation of the Use of Digital Storytelling in an Australian Undergraduate Literary Studies Program

ERIC Educational Resources Information Center

Clarke, Robert Garth Hipkins; Thomas, Sharon

2012-01-01

A growing number of university teachers advocate the benefits of multimedia and digital technologies in their classrooms. Such technologies are promoted: as a means to ensure the relevance of subject disciplines; and, as tools of engagement to assist students to meet their learning outcomes. Digital storytelling or narration is one example of how…

Technology Roadmap Instrumentation, Control, and Human-Machine Interface to Support DOE Advanced Nuclear Energy Programs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donald D Dudenhoeffer; Burce P Hallbert

Instrumentation, Controls, and Human-Machine Interface (ICHMI) technologies are essential to ensuring delivery and effective operation of optimized advanced Generation IV (Gen IV) nuclear energy systems. In 1996, the Watts Bar I nuclear power plant in Tennessee was the last U.S. nuclear power plant to go on line. It was, in fact, built based on pre-1990 technology. Since this last U.S. nuclear power plant was designed, there have been major advances in the field of ICHMI systems. Computer technology employed in other industries has advanced dramatically, and computing systems are now replaced every few years as they become functionally obsolete. Functionalmore » obsolescence occurs when newer, more functional technology replaces or supersedes an existing technology, even though an existing technology may well be in working order.Although ICHMI architectures are comprised of much of the same technology, they have not been updated nearly as often in the nuclear power industry. For example, some newer Personal Digital Assistants (PDAs) or handheld computers may, in fact, have more functionality than the 1996 computer control system at the Watts Bar I plant. This illustrates the need to transition and upgrade current nuclear power plant ICHMI technologies.« less

Digital health technology for use in patients with serious mental illness: a systematic review of the literature.

PubMed

Batra, Sonal; Baker, Ross A; Wang, Tao; Forma, Felicia; DiBiasi, Faith; Peters-Strickland, Timothy

2017-01-01

As the capabilities and reach of technology have expanded, there is an accompanying proliferation of digital technologies developed for use in the care of patients with mental illness. The objective of this review was to systematically search published literature to identify currently available health technologies and their intended uses for patients with serious mental illness. The Medline, Embase, and BIOSIS Previews electronic databases were searched to identify peer-reviewed English language articles that reported the use of digital, mobile, and other advanced technology in patients with schizophrenia/schizoaffective disorder, bipolar disorder, and major depressive disorder. Eligible studies were systematically reviewed based on Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Eighteen studies that met the inclusion criteria were identified. Digital health technologies (DHTs) assessed in the selected studies included mobile applications (apps), digital medicine, digital personal health records, and an electronic pill container. Smartphone apps accounted for the largest share of DHTs. The intended uses of DHTs could be broadly classified as monitoring to gain a better understanding of illness, clinical assessment, and intervention. Overall, studies indicated high usability/feasibility and efficacy/effectiveness, with several reporting validity against established clinical scales. Users were generally engaged with the DHT, and mobile assessments were deemed helpful in monitoring disease symptoms. Rapidly proliferating digital technologies seem to be feasible for short-term use in patients with serious mental illness; nevertheless, long-term effectiveness data from naturalistic studies will help demonstrate their usefulness and facilitate their adoption and integration into the mental health-care system.

Digital health technology for use in patients with serious mental illness: a systematic review of the literature

PubMed Central

Batra, Sonal; Baker, Ross A; Wang, Tao; Forma, Felicia; DiBiasi, Faith; Peters-Strickland, Timothy

2017-01-01

Background As the capabilities and reach of technology have expanded, there is an accompanying proliferation of digital technologies developed for use in the care of patients with mental illness. The objective of this review was to systematically search published literature to identify currently available health technologies and their intended uses for patients with serious mental illness. Materials and methods The Medline, Embase, and BIOSIS Previews electronic databases were searched to identify peer-reviewed English language articles that reported the use of digital, mobile, and other advanced technology in patients with schizophrenia/schizoaffective disorder, bipolar disorder, and major depressive disorder. Eligible studies were systematically reviewed based on Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Results Eighteen studies that met the inclusion criteria were identified. Digital health technologies (DHTs) assessed in the selected studies included mobile applications (apps), digital medicine, digital personal health records, and an electronic pill container. Smartphone apps accounted for the largest share of DHTs. The intended uses of DHTs could be broadly classified as monitoring to gain a better understanding of illness, clinical assessment, and intervention. Overall, studies indicated high usability/feasibility and efficacy/effectiveness, with several reporting validity against established clinical scales. Users were generally engaged with the DHT, and mobile assessments were deemed helpful in monitoring disease symptoms. Conclusion Rapidly proliferating digital technologies seem to be feasible for short-term use in patients with serious mental illness; nevertheless, long-term effectiveness data from naturalistic studies will help demonstrate their usefulness and facilitate their adoption and integration into the mental health-care system. PMID:29042823

A Phenomenographical Study of Voluntary Digital Exclusion

ERIC Educational Resources Information Center

Anderson, Derrick L.

2012-01-01

Traditionally scholars have used the digital divide and technology acceptance model definitions when examining why some people elect not to use certain information and communications technologies. When examining the phenomenon referred to as voluntary digital exclusion, the use of these classic definitions is woefully inadequate. They do not…

Essays on the Digital Divide

ERIC Educational Resources Information Center

Abdelfattah, Belal M. T.

2013-01-01

The digital divide is a phenomenon that is globally persistent, despite rapidly decreasing costs in technology. While much of the variance in the adoption and use of information communication technology (ICT) that defines the digital divide can be explained by socioeconomic and demographic variables, there is still significant unaccounted variance…

The Use of Digital Narratives to Enhance Counseling and Psychotherapy

ERIC Educational Resources Information Center

Pillay, Yegan

2009-01-01

Technological advances have impinged on every aspect of contemporary phenomenological experiences, including counseling and psychotherapy. The author explores the intersection of narrative therapy, specifically the traditional memory book, with the advances in information technology in the formulation of the digital memory book. The digital memory…

Outcasts on the Inside: Academics Reinventing Themselves Online

ERIC Educational Resources Information Center

Costa, Cristina

2015-01-01

Recent developments in digital scholarship point out that academic practices supported by technologies may not only be transformed through the obvious process of digitization, but also renovated through distributed knowledge networks that digital technologies enable, and the practices of openness that such networks develop. Yet, this apparent…

Learning to Read in the Digital Age

ERIC Educational Resources Information Center

Rose, David; Dalton, Bridget

2009-01-01

The digital age offers transformative opportunities for individualization of learning. First, modern imaging technologies have changed our understanding of learning and the sources and ranges of its diversity. Second, digital technologies make it possible to design learning environments that are responsive to individual differences. We draw on…

Conservation Is Job One.

ERIC Educational Resources Information Center

Hatzai, Glen

1998-01-01

The University of Michigan, winner of a federal award for its campus energy conservation, has developed a building automation system that uses direct-digital-control technology to manage energy use. The project, undertaken in partnership with an energy management company, has saved over $10 million since its inception, and includes a revolving…

Decision generation tools and Bayesian inference

NASA Astrophysics Data System (ADS)

Jannson, Tomasz; Wang, Wenjian; Forrester, Thomas; Kostrzewski, Andrew; Veeris, Christian; Nielsen, Thomas

2014-05-01

Digital Decision Generation (DDG) tools are important software sub-systems of Command and Control (C2) systems and technologies. In this paper, we present a special type of DDGs based on Bayesian Inference, related to adverse (hostile) networks, including such important applications as terrorism-related networks and organized crime ones.

The Digital Divide through the Lens of Critical Race Theory: The Digitally Denied

ERIC Educational Resources Information Center

Hollins, Stacy Gee

2015-01-01

The purpose of this qualitative research study was to examine African American community college students' availability to technological resources and how that availability affects their success. In this study, technological resources include access to the internet, software, hardware, technology training, technology support, and community…

Aligning Digital Video Technology with Game Pedagogy in Physical Education

ERIC Educational Resources Information Center

Koekoek, Jeroen; van der Mars, Hans; van der Kamp, John; Walinga, Wytse; van Hilvoorde, Ivo

2018-01-01

The rapid development of digital technology has expanded the prospects and promises for its application in physical education programs. Physical educators are becoming increasingly interested in technology but often remain inadequately equipped to effectively integrate these technological resources in their daily practice, and/or lack the…

Pre-School Children Creating and Communicating with Digital Technologies in the Home

ERIC Educational Resources Information Center

McPake, Joanna; Plowman, Lydia; Stephen, Christine

2013-01-01

There is a limited literature on pre-school children's experiences with "digital technologies" at home and little discussion of the ways in which children harness these technologies for their own purposes. This paper discusses findings drawn from three studies that investigated the role of "domestic technologies" and…

Examining Student Digital Artifacts during a Year-Long Technology Integration Initiative

ERIC Educational Resources Information Center

Rodriguez, Prisca M.; Frey, Chris; Dawson, Kara; Liu, Feng; Ritzhaupt, Albert D.

2012-01-01

This study was situated within a year-long, statewide technology integration initiative designed to support technology integration within science, technology, engineering, and math classrooms. It examined the elements used in student artifacts in an attempt to investigate trends in digital artifact creation. Among several conclusions, this…

Digital Technology Education and Its Impact on Traditional Academic Roles and Practice

ERIC Educational Resources Information Center

Sappey, Jennifer; Relf, Stephen

2010-01-01

This paper explores the interface between digital technologies and the teaching labour process in Australian higher education. We develop an adaptation of the seminal Clark (1983, 1994, 2001) and Kozma (1991, 1994) debate about whether technology merely delivers educational content unchanged--technology as the "delivery truck"--or…

Health promotion in the digital era: a critical commentary.

PubMed

Lupton, Deborah

2015-03-01

A range of digitized health promotion practices have emerged in the digital era. Some of these practices are voluntarily undertaken by people who are interested in improving their health and fitness, but many others are employed in the interests of organizations and agencies. This article provides a critical commentary on digitized health promotion. I begin with an overview of the types of digital technologies that are used for health promotion, and follow this with a discussion of the socio-political implications of such use. It is contended that many digitized health promotion strategies focus on individual responsibility for health and fail to recognize the social, cultural and political dimensions of digital technology use. The increasing blurring between voluntary health promotion practices, professional health promotion, government and corporate strategies requires acknowledgement, as does the increasing power wielded by digital media corporations over digital technologies and the data they generate. These issues provoke questions for health promotion as a practice and field of research that hitherto have been little addressed. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

A Statistical Testing Approach for Quantifying Software Reliability; Application to an Example System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, Tsong-Lun; Varuttamaseni, Athi; Baek, Joo-Seok

The U.S. Nuclear Regulatory Commission (NRC) encourages the use of probabilistic risk assessment (PRA) technology in all regulatory matters, to the extent supported by the state-of-the-art in PRA methods and data. Although much has been accomplished in the area of risk-informed regulation, risk assessment for digital systems has not been fully developed. The NRC established a plan for research on digital systems to identify and develop methods, analytical tools, and regulatory guidance for (1) including models of digital systems in the PRAs of nuclear power plants (NPPs), and (2) incorporating digital systems in the NRC's risk-informed licensing and oversight activities.more » Under NRC's sponsorship, Brookhaven National Laboratory (BNL) explored approaches for addressing the failures of digital instrumentation and control (I and C) systems in the current NPP PRA framework. Specific areas investigated included PRA modeling digital hardware, development of a philosophical basis for defining software failure, and identification of desirable attributes of quantitative software reliability methods. Based on the earlier research, statistical testing is considered a promising method for quantifying software reliability. This paper describes a statistical software testing approach for quantifying software reliability and applies it to the loop-operating control system (LOCS) of an experimental loop of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL).« less

Dental Students' Perceptions of Digital and Conventional Impression Techniques: A Randomized Controlled Trial.

PubMed

Zitzmann, Nicola U; Kovaltschuk, Irina; Lenherr, Patrik; Dedem, Philipp; Joda, Tim

2017-10-01

The aim of this randomized controlled trial was to analyze inexperienced dental students' perceptions of the difficulty and applicability of digital and conventional implant impressions and their preferences including performance. Fifty undergraduate dental students at a dental school in Switzerland were randomly divided into two groups (2×25). Group A first took digital impressions in a standardized phantom model and then conventional impressions, while the procedures were reversed for Group B. Participants were asked to complete a VAS questionnaire (0-100) on the level of difficulty and applicability (user/patient-friendliness) of both techniques. They were asked which technique they preferred and perceived to be more efficient. A quotient of "effective scan time per software-recorded time" (TRIOS) was calculated as an objective quality indicator for intraoral optical scanning (IOS). The majority of students perceived IOS as easier than the conventional technique. Most (72%) preferred the digital approach using IOS to take the implant impression to the conventional method (12%) or had no preference (12%). Although total work was similar for males and females, the TRIOS quotient indicated that male students tended to use their time more efficiently. In this study, dental students with no clinical experience were very capable of acquiring digital tools, indicating that digital impression techniques can be included early in the dental curriculum to help them catch up with ongoing development in computer-assisted technologies used in oral rehabilitation.

Color management systems: methods and technologies for increased image quality

NASA Astrophysics Data System (ADS)

Caretti, Maria

1997-02-01

All the steps in the imaging chain -- from handling the originals in the prepress to outputting them on any device - - have to be well calibrated and adjusted to each other, in order to reproduce color images in a desktop environment as accurate as possible according to the original. Today most of the steps in the prepress production are digital and therefore it is realistic to believe that the color reproduction can be well controlled. This is true thanks to the last years development of fast, cost effective scanners, digital sources and digital proofing devices not the least. It is likely to believe that well defined tools and methods to control this imaging flow will lead to large cost and time savings as well as increased overall image quality. Until now, there has been a lack of good, reliable, easy-to- use systems (e.g. hardware, software, documentation, training and support) in an extent that has made them accessible to the large group of users of graphic arts production systems. This paper provides an overview of the existing solutions to manage colors in a digital pre-press environment. Their benefits and limitations are discussed as well as how they affect the production workflow and organization. The difference between a color controlled environment and one that is not is explained.

Understanding dental CAD/CAM for restorations--the digital workflow from a mechanical engineering viewpoint.

PubMed

Tapie, L; Lebon, N; Mawussi, B; Fron Chabouis, H; Duret, F; Attal, J-P

2015-01-01

As digital technology infiltrates every area of daily life, including the field of medicine, so it is increasingly being introduced into dental practice. Apart from chairside practice, computer-aided design/computer-aided manufacturing (CAD/CAM) solutions are available for creating inlays, crowns, fixed partial dentures (FPDs), implant abutments, and other dental prostheses. CAD/CAM dental solutions can be considered a chain of digital devices and software for the almost automatic design and creation of dental restorations. However, dentists who want to use the technology often do not have the time or knowledge to understand it. A basic knowledge of the CAD/CAM digital workflow for dental restorations can help dentists to grasp the technology and purchase a CAM/CAM system that meets the needs of their office. This article provides a computer-science and mechanical-engineering approach to the CAD/CAM digital workflow to help dentists understand the technology.

Integration of tablet technologies in the e-laboratory of cytology: a health technology assessment.

PubMed

Giansanti, Daniele; Pochini, Marco; Giovagnoli, Maria Rosaria

2014-10-01

Although tablet systems are becoming a powerful technology, particularly useful in every application of medical imaging, to date no one has investigated the acceptance and performance of this technology in digital cytology. The specific aims of the work were (1) to design a health technology assessment (HTA) tool to assess, in terms of performance and acceptance, the introduction of tablet technologies (wearable, portable, and non portable) in the e-laboratories of cytology and (2) to test the tool in a first significant application of digital cytology. An HTA tool was proposed operating on a domain of five dimensions of investigation comprising the basic information of the product of digital cytology, the perceived subjective quality of images, the assessment of the virtual navigation on the e-slide, the assessment of the information and communication technologies features, and the diagnostic power. Six e-slides regarding studies of cervicovaginal cytology digitalized by means of an Aperio ( www.aperio.com ) scanner and uploaded onto the www.digitalslide.it Web site were used for testing the methodology on three different network connections. Three experts of cytology successfully tested the methodology on seven tablets found suitable for the study in their own standard configuration. Specific indexes furnished by the tool indicated both a high degree of performance and subjective acceptance of the investigated technology. The HTA tool thus could be useful to investigate new tablet technologies in digital cytology and furnish stakeholders with useful information that may help them make decisions involving the healthcare system. From a global point of view the study demonstrates the feasibility of using the tablet technology in digital cytology.

Quiet Clean Short-haul Experimental Engine (QCSEE). Under-The-Wing (UTW) engine boilerplate nacelle test report. Volume 3: Mechanical performance

NASA Technical Reports Server (NTRS)

1977-01-01

Results of initial tests of the under the wing experimental engine and boilerplate nacelle are presented. The mechanical performance of the engine is reported with emphasis on the advanced technology components. Technology elements of the propulsion system covered include: system dynamics, composite fan blades, reduction gear, lube and accessory drive system, fan frame, inlet, core cowl cooling, fan exhaust nozzle, and digital control system.

Coming cockpit avionics

NASA Technical Reports Server (NTRS)

Mciver, D.; Hatfield, J. J.

1978-01-01

Digital and display technology combined with human factors research under development today are expected to become operational in the commercial aircraft of the 1990s. Attention is given to reducing the pilot's workload and increasing aircraft reliability through integration of electronic systems, and through multi-mode displays. Recent advances in display technology are outlined, including electroluminescent panels, beam penetration color CRTs, liquid crystal modules, and LED panels and indicators. Research cockpits are described in terms of simplification of aircraft systems evaluation and control.

Digital Radiographic Image Processing and Analysis.

PubMed

Yoon, Douglas C; Mol, André; Benn, Douglas K; Benavides, Erika

2018-07-01

This article describes digital radiographic imaging and analysis from the basics of image capture to examples of some of the most advanced digital technologies currently available. The principles underlying the imaging technologies are described to provide a better understanding of their strengths and limitations. Copyright © 2018 Elsevier Inc. All rights reserved.

Digital Participatory Pedagogy: Digital Participation as a Method for Technology Integration in Curriculum

ERIC Educational Resources Information Center

Dooley, Caitlin McMunn; Lewis Ellison, Tisha; Welch, Meghan M.; Allen, Mindy; Bauer, Dennis

2016-01-01

This qualitative participatory action research study provides two case studies to demonstrate how teachers in Grades 4 and 6 integrated digital tools into everyday, content-focused classroom instruction. The study demonstrates how teachers' technological pedagogical knowledge might combine with a participatory stance to encourage students to…

Digital Natives Come to Preschool: Implications for Early Childhood Practice

ERIC Educational Resources Information Center

Zevenbergen, Robyn

2007-01-01

This article explores the implications of young learners' dispositions towards the use of digital technologies in contemporary early childhood settings. It is proposed that young learners have grown up in very different social conditions from previous generations, mainly through the saturation of digital technologies, in particular computers. This…

Digital Media and "Girling" at an Elite Girls' School

ERIC Educational Resources Information Center

Charles, Claire

2007-01-01

In this article, I draw on Judith Butler's notion of performativity to investigate the role of digital technologies in processes of gendered subjectification (or "girling") in elite girls' education. Elite girls' schooling is a site where the potential of digital technologies in mediating student-led constructions and explorations of…

A Business Educator's Guide to Transitioning to a Digital Curriculum

ERIC Educational Resources Information Center

Roberts, Scott D.; Rains, Russell E.; Perry, Gregory E.

2012-01-01

The authors, representing three key digital media business disciplines, present a case for how business curriculum could be updated to include a strong digital element without recreating the entire business school enterprise or spending millions on new faculty and technology. The three key disciplines are technology, law, and marketing.

Perspectives on Communicating with the Net Generation

ERIC Educational Resources Information Center

Zimmerman, Lynn; Milligan, Anastasia Trekles

2008-01-01

Lynn Zimmerman and Anastasia Trekles Milligan examine technological communication from the perspectives of two instructors, one a digital immigrant and the other a digital native. Today's students are digital natives, reared in a world permeated by interactive technology; as a result, they are used to a model of communication that is significantly…

From Digital Divide to Digital Democracy.

ERIC Educational Resources Information Center

de los Santos, Gerardo E., Ed.; de los Santos, Alfredo G., Jr., Ed.; Milliron, Mark David, Ed.

This publication is one of many efforts of the League for Innovation in the Community College to address the issue of societal technology access and learning needs. This work addresses the issue of the digital divide, which includes the often conflicting perspectives of information technology (IT) access and literacy needs held by government…

The Rise of the Digital Public Library

ERIC Educational Resources Information Center

McKendrick, Joseph

2012-01-01

There is a growing shift to digital offerings among public libraries. Libraries increasingly are fulfilling roles as technology hubs for their communities, with high demand for technology and career development training resources. Ebooks and other digital materials are on the rise, while print is being scaled back. More libraries are turning to…

Digital Exclusion: Coming out from behind Closed Doors

ERIC Educational Resources Information Center

Watling, Sue

2011-01-01

Government visions of a digital future show little indication of how disabled people, reliant on access technology, will participate. Access technology has the potential to offer independent use of the Internet but many disabled people already face barriers that prevent them having equitable digital experiences. Multiple obstacles include high…

Digital Learning in Schools: Conceptualizing the Challenges and Influences on Teacher Practice

ERIC Educational Resources Information Center

Blundell, Christopher; Lee, Kar-Tin; Nykvist, Shaun

2016-01-01

Digital technologies are an important requirement for curriculum expectations, including general ICT capability and STEM education. These technologies are also positioned as mechanisms for educational reform via transformation of teacher practice. It seems, however, that wide-scale transformation of teacher practice and digital learning remain…

Play, Creativity and Digital Cultures. Routledge Research in Education

ERIC Educational Resources Information Center

Willett, Rebekah, Ed.; Robinson, Muriel, Ed.; Marsh, Jackie, Ed.

2011-01-01

Recent work on children's digital cultures has identified a range of literacies emerging through children's engagement with new media technologies. This edited collection focuses on children's digital cultures, specifically examining the role of play and creativity in learning with these new technologies. The chapters in this book were contributed…

Beyond Preservation: New Directions for Technological Innovation through Intangible Cultural Heritage

ERIC Educational Resources Information Center

Robbins, Christopher

2010-01-01

While many digitization projects are currently underway, to help preserve Indigenous traditions, few explore the full potential of the development of digital media and networked technology through Indigenous cultures. This paper outlines the three phases necessary for a robust digital preservation, promotion and growth project: 1) Straightforward…

Digital Simulations: Facilitating Transition for Students with Disabilities

ERIC Educational Resources Information Center

Zionch, Allenda

2011-01-01

Today's students are digital natives. From computers to MP3 players, the everyday use of technology in society underscores the necessity of using technology in education. The use of digital simulations especially has had positive outcomes for students with disabilities in generalizing various life skills necessary for transition beyond high…

Multi-channel photon counting DOT system based on digital lock-in detection technique

NASA Astrophysics Data System (ADS)

Wang, Tingting; Zhao, Huijuan; Wang, Zhichao; Hou, Shaohua; Gao, Feng

2011-02-01

Relying on deeper penetration of light in the tissue, Diffuse Optical Tomography (DOT) achieves organ-level tomography diagnosis, which can provide information on anatomical and physiological features. DOT has been widely used in imaging of breast, neonatal cerebral oxygen status and blood oxygen kinetics observed by its non-invasive, security and other advantages. Continuous wave DOT image reconstruction algorithms need the measurement of the surface distribution of the output photon flow inspired by more than one driving source, which means that source coding is necessary. The most currently used source coding in DOT is time-division multiplexing (TDM) technology, which utilizes the optical switch to switch light into optical fiber of different locations. However, in case of large amounts of the source locations or using the multi-wavelength, the measurement time with TDM and the measurement interval between different locations within the same measurement period will therefore become too long to capture the dynamic changes in real-time. In this paper, a frequency division multiplexing source coding technology is developed, which uses light sources modulated by sine waves with different frequencies incident to the imaging chamber simultaneously. Signal corresponding to an individual source is obtained from the mixed output light using digital phase-locked detection technology at the detection end. A digital lock-in detection circuit for photon counting measurement system is implemented on a FPGA development platform. A dual-channel DOT photon counting experimental system is preliminary established, including the two continuous lasers, photon counting detectors, digital lock-in detection control circuit, and codes to control the hardware and display the results. A series of experimental measurements are taken to validate the feasibility of the system. This method developed in this paper greatly accelerates the DOT system measurement, and can also obtain the multiple measurements in different source-detector locations.

Controlling the digital transfer process

NASA Astrophysics Data System (ADS)

Brunner, Felix

1997-02-01

The accuracy of today's color management systems fails to satisfy the requirements of the graphic arts market. A first explanation for this is that color calibration charts on which these systems rely, because of print technical reasons, are subject to color deviations and inconsistencies. A second reason is that colorimetry describes the human visual perception of color differences and has no direct relation to the rendering technology itself of a proofing or printing device. The author explains that only firm process control of the many parameters in offset printing by means of a system as for example EUROSTANDARD System Brunner, can lead to accurate and consistent calibration of scanner, display, proof and print. The same principles hold for the quality management of digital presses.

Performance seeking control program overview

NASA Technical Reports Server (NTRS)

Orme, John S.

1995-01-01

The Performance Seeking Control (PSC) program evolved from a series of integrated propulsion-flight control research programs flown at NASA Dryden Flight Research Center (DFRC) on an F-15. The first of these was the Digital Electronic Engine Control (DEEC) program and provided digital engine controls suitable for integration. The DEEC and digital electronic flight control system of the NASA F-15 were ideally suited for integrated controls research. The Advanced Engine Control System (ADECS) program proved that integrated engine and aircraft control could improve overall system performance. The objective of the PSC program was to advance the technology for a fully integrated propulsion flight control system. Whereas ADECS provided single variable control for an average engine, PSC controlled multiple propulsion system variables while adapting to the measured engine performance. PSC was developed as a model-based, adaptive control algorithm and included four optimization modes: minimum fuel flow at constant thrust, minimum turbine temperature at constant thrust, maximum thrust, and minimum thrust. Subsonic and supersonic flight testing were conducted at NASA Dryden covering the four PSC optimization modes and over the full throttle range. Flight testing of the PSC algorithm, conducted in a series of five flight test phases, has been concluded at NASA Dryden covering all four of the PSC optimization modes. Over a three year period and five flight test phases 72 research flights were conducted. The primary objective of flight testing was to exercise each PSC optimization mode and quantify the resulting performance improvements.

Application of space technologies for the purpose of education at the Belarusian state university

NASA Astrophysics Data System (ADS)

Liashkevich, Siarhey

Application of space technologies for the purpose of education at the Aerospace Educational Center of Belarusian state university is discussed. The aim of the work is to prepare launch of small satellite. Students are expected to participate in the design of control station, systems of communication, earth observation, navigation, and positioning. Benefit of such project-based learning from economical perspective is discussed. At present our training system at the base of EyasSat classroom satellite is used for management of satellite orientation and stabilization system. Principles of video processing, communication technologies and informational security for small spacecraft are developed at the base of Wi9M-2443 developer kit. More recent equipment allows obtaining the skills in digital signal processing at the base of FPGA. Development of ground station includes setup of 2.6 meter diameter dish for L-band, and spiral rotational antennas for UHF and VHF bands. Receiver equipment from National Instruments is used for digital signal processing and signal management.

Database application of digital medical X-rays and labs: computerization, storage, retrieval, interpretation, and distribution.

PubMed

Hatcher, Myron; Tabriziani, Hossein; Heetebry, Irene

2005-08-01

Stenter lets the health care worker order an X-ray that is produced as a computer image rather than on flat film. The health care provider can be in any location with the correct equipment, and view the digital image. The dimensions of this discussion are extensive. The cost savings because of reduced media and storage cost is substantial. Health care quality can be improved because of the ability to obtain consultation via telemedicine and the enhanced ability to track medical problems over time via trends. The major downside is the limited cost imbursement system to pay for technology. Unfortunately, this may impact on the improved quality of care. In simple terms someone needs to pay for the technology and the quality of health care needs to be maintained or improved. The real cost to the health care systems needs to be correctly calculated and inappropriate charging kept to a minimum. Specific costs need to be kept in mind and the first is the cost for new staff or staff training. The number of health care providers that are able to read the X-ray can be enlarged remembering that only American Board Certified Radiologists are allowed to give the final recommendation. How do we view the cost of missing something? It could be argued that this risk will be reduced because of improved technology for obtaining the digital X-ray and improved enhancement software. One way to view this situation is to include technology, management, and organization. The cost and benefits occur through the interplay of all three dimensions. The development of digital imaging hardware and artificial intelligence software will demand change in the management and organization. The organization will require changes in its design to accommodate the technology as to support and resources. Management will evolve to include methods for control and monitoring this technology. Business processes and standard operating procedures will change to integrate the technology into the organization in the most effective and efficient manner.

Transition in Gas Turbine Control System Architecture: Modular, Distributed, and Embedded

NASA Technical Reports Server (NTRS)

Culley, Dennis

2010-01-01

Controls systems are an increasingly important component of turbine-engine system technology. However, as engines become more capable, the control system itself becomes ever more constrained by the inherent environmental conditions of the engine; a relationship forced by the continued reliance on commercial electronics technology. A revolutionary change in the architecture of turbine-engine control systems will change this paradigm and result in fully distributed engine control systems. Initially, the revolution will begin with the physical decoupling of the control law processor from the hostile engine environment using a digital communications network and engine-mounted high temperature electronics requiring little or no thermal control. The vision for the evolution of distributed control capability from this initial implementation to fully distributed and embedded control is described in a roadmap and implementation plan. The development of this plan is the result of discussions with government and industry stakeholders

Toward virtual anatomy: a stereoscopic 3-D interactive multimedia computer program for cranial osteology.

PubMed

Trelease, R B

1996-01-01

Advances in computer visualization and user interface technologies have enabled development of "virtual reality" programs that allow users to perceive and to interact with objects in artificial three-dimensional environments. Such technologies were used to create an image database and program for studying the human skull, a specimen that has become increasingly expensive and scarce. Stereoscopic image pairs of a museum-quality skull were digitized from multiple views. For each view, the stereo pairs were interlaced into a single, field-sequential stereoscopic picture using an image processing program. The resulting interlaced image files are organized in an interactive multimedia program. At run-time, gray-scale 3-D images are displayed on a large-screen computer monitor and observed through liquid-crystal shutter goggles. Users can then control the program and change views with a mouse and cursor to point-and-click on screen-level control words ("buttons"). For each view of the skull, an ID control button can be used to overlay pointers and captions for important structures. Pointing and clicking on "hidden buttons" overlying certain structures triggers digitized audio spoken word descriptions or mini lectures.

Varifocal liquid lens based on microelectrofluidic technology.

PubMed

Chang, Jong-hyeon; Jung, Kyu-Dong; Lee, Eunsung; Choi, Minseog; Lee, Seungwan; Kim, Woonbae

2012-11-01

This Letter presents a tunable liquid lens based on microelectrofluidic technology. In the microelectrofluidic lens (MEFL), electrowetting in the hydrophobic surface channel induces the Laplace pressure difference between two fluidic interfaces on the lens aperture and the surface channel. Then, the pressure difference makes the lens curvature tunable. In spite of the contact angle saturation, the narrow surface channel increases the Laplace pressure to have a wide range of optical power variation in the MEFL. The magnitude of the applied voltage determines the lens curvature in the analog mode MEFL. Digital operation is also possible when the control electrodes of the MEFL are patterned to have an array. The lens aperture and maximum surface channel diameter were designed to 3.2 mm and 6.4 mm, respectively, with a channel height of 0.2 mm for an optical power range between +210 and -30 D. By switching the control electrodes, the averaged transit time in steps and turnaround time were as low as 2.4 ms and 16.5 ms, respectively, in good agreement with the simulation results. It is expected that the proposed MEFL may be widely used with advantages of wide variation of the optical power with fast and precise controllability in a digital manner.

The Future of Hearing Aid Technology

PubMed Central

Edwards, Brent

2007-01-01

Hearing aids have advanced significantly over the past decade, primarily due to the maturing of digital technology. The next decade should see an even greater number of innovations to hearing aid technology, and this article attempts to predict in which areas the new developments will occur. Both incremental and radical innovations in digital hearing aids will be driven by research advances in the following fields: (1) wireless technology, (2) digital chip technology, (3) hearing science, and (4) cognitive science. The opportunities and limitations for each of these areas will be discussed. Additionally, emerging trends such as connectivity and individualization will also drive new technology, and these are discussed within the context of the areas given here. PMID:17301336

Adoption and Use of Digital Technologies among General Dental Practitioners in the Netherlands

PubMed Central

van der Zande, Marieke M.; Gorter, Ronald C.; Aartman, Irene H. A.; Wismeijer, Daniel

2015-01-01

Objectives To investigate (1) the degree of digital technology adoption among general dental practitioners, and to assess (2) which personal and practice factors are associated with technology use. Methods A questionnaire was distributed among a stratified sample of 1000 general dental practitioners in the Netherlands, to measure the use of fifteen administrative, communicative, clinical and diagnostic technologies, as well as personal factors and dental practice characteristics. Results The response rate was 31.3%; 65.1% replied to the questionnaire on paper and 34.9% online. Each specific digital technology was used by between 93.2% and 6.8% of the dentists. Administrative technologies were generally used by more dentists than clinical technologies. Dentists had adopted an average number of 6.3±2.3 technologies. 22.5% were low technology users (0 to 4 technologies), 46.2% were intermediate technology users (5 to 7 technologies) and 31.3% were high technology users (8 to12 technologies). High technology users more frequently had a specialization (p<0.001), were younger on average (p=0.024), and worked more hours per week (p=0.003) than low technology users, and invested more hours per year in professional activities (p=0.026) than intermediate technology users. High technology use was also more common for dentists working in practices with a higher average number of patients per year (p<0.001), with more dentists working in the practice (p<0.001) and with more staff (p<0.001). Conclusion With few exceptions, all dentists use some or a substantial number of digital technologies. Technology use is associated with various patterns of person-specific factors, and is higher when working in larger dental practices. The findings provide insight into the current state of digital technology adoption in dental practices. Further exploration why some dentists are more reluctant to adopt technologies than others is valuable for the dental profession’s agility in adjusting to technological developments. PMID:25811594

Method and Process for the Creation of Modeling and Simulation Tools for Human Crowd Behavior

DTIC Science & Technology

2014-07-23

Support• Program Executive Office Ground Combat Systems • Program Executive Office Soldier TACOM LCMC MG Michael J. Terry Assigned/Direct Support...environmental technologies and explosive ordnance disposal Fire Control: Battlefield digitization; embedded system software; aero ballistics and...MRAD – Handheld stand-off NLW operated by Control Force • Simulated Projectile Weapon • Simulated Handheld Directed Energy NLW ( VDE ) – Simulated

System-Level Integrated Circuit (SLIC) Technology Development for Phased Array Antenna Applications

NASA Technical Reports Server (NTRS)

Windyka, John A.; Zablocki, Ed G.

1997-01-01

This report documents the efforts and progress in developing a 'system-level' integrated circuit, or SLIC, for application in advanced phased array antenna systems. The SLIC combines radio-frequency (RF) microelectronics, digital and analog support circuitry, and photonic interfaces into a single micro-hybrid assembly. Together, these technologies provide not only the amplitude and phase control necessary for electronic beam steering in the phased array, but also add thermally-compensated automatic gain control, health and status feedback, bias regulation, and reduced interconnect complexity. All circuitry is integrated into a compact, multilayer structure configured for use as a two-by-four element phased array module, operating at 20 Gigahertz, using a Microwave High-Density Interconnect (MHDI) process. The resultant hardware is constructed without conventional wirebonds, maintains tight inter-element spacing, and leads toward low-cost mass production. The measured performances and development issues associated with both the two-by-four element module and the constituent elements are presented. Additionally, a section of the report describes alternative architectures and applications supported by the SLIC electronics. Test results show excellent yield and performance of RF circuitry and full automatic gain control for multiple, independent channels. Digital control function, while suffering from lower manufacturing yield, also proved successful.

"Technological Me": Young Children's Use of Technology across Their Home and School Contexts

ERIC Educational Resources Information Center

Gronn, Donna; Scott, Anne; Edwards, Susan; Henderson, Michael

2014-01-01

Research into children's learning with digital technologies is represented by a growing body of literature examining the relationship between home-school technological practices. A focus of this work is on the notion of a "digital-disconnect" between home and school. This argument suggests that children are such native users of…

Disruptive Technology Enhanced Learning: The Use and Misuse of Digital Technologies in Higher Education

ERIC Educational Resources Information Center

Flavin, Michael

2017-01-01

This book is about how technologies are used in practice to support learning and teaching in higher education. Despite digitization and e-learning becoming ever-increasingly popular in university teaching settings, this book convincingly argues instead in favour of simple and convenient technologies, thus disrupting traditional patterns of…

Making Sense of Young People, Education and Digital Technology: The Role of Sociological Theory

ERIC Educational Resources Information Center

Selwyn, Neil

2012-01-01

This paper considers the contribution of sociological theory to the academic study of young people, education and digital technology. First it discusses the shortcomings of the technological and socially determinist views of technology and education that prevail in current academic and policy discussions. Against this background the paper outlines…

Digitization of the human body in the present-day economy

NASA Astrophysics Data System (ADS)

D'Apuzzo, Nicola

2004-12-01

In this paper we report on the historic development of human body digitization and on the actual state of commercially available technology. Complete systems for the digitization of the human body exist since more than ten years. One of the main users of this technology was the entertainment industry. Every new movie excited with attractive visual effects, but only few people knew that the most thrilling cuts were realized by using virtual persons. The faces and bodies of actors were digitized and the "virtual twin" replaced the actor in the movie. Nowadays, the state of the human body digitization is so high that it is not possible any more to distinguish the real actor from the virtual one. Indeed, for the rush technical development has to be thanked the movie industry, which was one of the strong economic motors for this technology. Today, with the possibility of a massive cost reduction given by new technologies, methods for digitization of the human body are used also in other fields of application, such as ergonomics, medical applications, computer games, biometry and anthropometrics. With the time, this technology becomes interesting also for sport, fitness, fashion and beauty. A large expansion of human body digitization is expected in the near future. To date, different technologies are used commercially for the measurement of the human body. They can be divided into three distinguished groups: laser-scanning, projection of light patterns, combination modeling and image processing. The different solutions have strengths and weaknesses that profile their suitability for specific applications. This paper gives an overview of their differences and characteristics and expresses clues for the selection of the adequate method. Practical examples of commercial exploitation of human body digitization are also presented and new interesting perspectives are introduced.

Digitization of the human body in the present-day economy

NASA Astrophysics Data System (ADS)

D'Apuzzo, Nicola

2005-01-01

In this paper we report on the historic development of human body digitization and on the actual state of commercially available technology. Complete systems for the digitization of the human body exist since more than ten years. One of the main users of this technology was the entertainment industry. Every new movie excited with attractive visual effects, but only few people knew that the most thrilling cuts were realized by using virtual persons. The faces and bodies of actors were digitized and the "virtual twin" replaced the actor in the movie. Nowadays, the state of the human body digitization is so high that it is not possible any more to distinguish the real actor from the virtual one. Indeed, for the rush technical development has to be thanked the movie industry, which was one of the strong economic motors for this technology. Today, with the possibility of a massive cost reduction given by new technologies, methods for digitization of the human body are used also in other fields of application, such as ergonomics, medical applications, computer games, biometry and anthropometrics. With the time, this technology becomes interesting also for sport, fitness, fashion and beauty. A large expansion of human body digitization is expected in the near future. To date, different technologies are used commercially for the measurement of the human body. They can be divided into three distinguished groups: laser-scanning, projection of light patterns, combination modeling and image processing. The different solutions have strengths and weaknesses that profile their suitability for specific applications. This paper gives an overview of their differences and characteristics and expresses clues for the selection of the adequate method. Practical examples of commercial exploitation of human body digitization are also presented and new interesting perspectives are introduced.

Digital image analysis in pathology: benefits and obligation.

PubMed

Laurinavicius, Arvydas; Laurinaviciene, Aida; Dasevicius, Darius; Elie, Nicolas; Plancoulaine, Benoît; Bor, Catherine; Herlin, Paulette

2012-01-01

Pathology has recently entered the era of personalized medicine. This brings new expectations for the accuracy and precision of tissue-based diagnosis, in particular, when quantification of histologic features and biomarker expression is required. While for many years traditional pathologic diagnosis has been regarded as ground truth, this concept is no longer sufficient in contemporary tissue-based biomarker research and clinical use. Another major change in pathology is brought by the advancement of virtual microscopy technology enabling digitization of microscopy slides and presenting new opportunities for digital image analysis. Computerized vision provides an immediate benefit of increased capacity (automation) and precision (reproducibility), but not necessarily the accuracy of the analysis. To achieve the benefit of accuracy, pathologists will have to assume an obligation of validation and quality assurance of the image analysis algorithms. Reference values are needed to measure and control the accuracy. Although pathologists' consensus values are commonly used to validate these tools, we argue that the ground truth can be best achieved by stereology methods, estimating the same variable as an algorithm is intended to do. Proper adoption of the new technology will require a new quantitative mentality in pathology. In order to see a complete and sharp picture of a disease, pathologists will need to learn to use both their analogue and digital eyes.

Integrated electrofluidic circuits: pressure sensing with analog and digital operation functionalities for microfluidics.

PubMed

Wu, Chueh-Yu; Lu, Jau-Ching; Liu, Man-Chi; Tung, Yi-Chung

2012-10-21

Microfluidic technology plays an essential role in various lab on a chip devices due to its desired advantages. An automated microfluidic system integrated with actuators and sensors can further achieve better controllability. A number of microfluidic actuation schemes have been well developed. In contrast, most of the existing sensing methods still heavily rely on optical observations and external transducers, which have drawbacks including: costly instrumentation, professional operation, tedious interfacing, and difficulties of scaling up and further signal processing. This paper reports the concept of electrofluidic circuits - electrical circuits which are constructed using ionic liquid (IL)-filled fluidic channels. The developed electrofluidic circuits can be fabricated using a well-developed multi-layer soft lithography (MSL) process with polydimethylsiloxane (PDMS) microfluidic channels. Electrofluidic circuits allow seamless integration of pressure sensors with analog and digital operation functions into microfluidic systems and provide electrical readouts for further signal processing. In the experiments, the analog operation device is constructed based on electrofluidic Wheatstone bridge circuits with electrical outputs of the addition and subtraction results of the applied pressures. The digital operation (AND, OR, and XOR) devices are constructed using the electrofluidic pressure controlled switches, and output electrical signals of digital operations of the applied pressures. The experimental results demonstrate the designed functions for analog and digital operations of applied pressures are successfully achieved using the developed electrofluidic circuits, making them promising to develop integrated microfluidic systems with capabilities of precise pressure monitoring and further feedback control for advanced lab on a chip applications.

Using information and communication technology (ICT) to the maximum: learning and teaching biology with limited digital technologies

NASA Astrophysics Data System (ADS)

Van Rooy, Wilhelmina S.

2012-04-01

Background: The ubiquity, availability and exponential growth of digital information and communication technology (ICT) creates unique opportunities for learning and teaching in the senior secondary school biology curriculum. Digital technologies make it possible for emerging disciplinary knowledge and understanding of biological processes previously too small, large, slow or fast to be taught. Indeed, much of bioscience can now be effectively taught via digital technology, since its representational and symbolic forms are in digital formats. Purpose: This paper is part of a larger Australian study dealing with the technologies and modalities of learning biology in secondary schools. Sample: The classroom practices of three experienced biology teachers, working in a range of NSW secondary schools, are compared and contrasted to illustrate how the challenges of limited technologies are confronted to seamlessly integrate what is available into a number of molecular genetics lessons to enhance student learning. Design and method: The data are qualitative and the analysis is based on video classroom observations and semi-structured teacher interviews. Results: Findings indicate that if professional development opportunities are provided where the pedagogy of learning and teaching of both the relevant biology and its digital representations are available, then teachers see the immediate pedagogic benefit to student learning. In particular, teachers use ICT for challenging genetic concepts despite limited computer hardware and software availability. Conclusion: Experienced teachers incorporate ICT, however limited, in order to improve the quality of student learning.

Bridging the digital divide through the integration of computer and information technology in science education: An action research study

NASA Astrophysics Data System (ADS)

Brown, Gail Laverne

The presence of a digital divide, computer and information technology integration effectiveness, and barriers to continued usage of computer and information technology were investigated. Thirty-four African American and Caucasian American students (17 males and 17 females) in grades 9--11 from 2 Georgia high school science classes were exposed to 30 hours of hands-on computer and information technology skills. The purpose of the exposure was to improve students' computer and information technology skills. Pre-study and post-study skills surveys, and structured interviews were used to compare race, gender, income, grade-level, and age differences with respect to computer usage. A paired t-test and McNemar test determined mean differences between student pre-study and post-study perceived skills levels. The results were consistent with findings of the National Telecommunications and Information Administration (2000) that indicated the presence of a digital divide and digital inclusion. Caucasian American participants were found to have more at-home computer and Internet access than African American participants, indicating that there is a digital divide by ethnicity. Caucasian American females were found to have more computer and Internet access which was an indication of digital inclusion. Sophomores had more at-home computer access and Internet access than other levels indicating digital inclusion. Students receiving regular meals had more computer and Internet access than students receiving free/reduced meals. Older students had more computer and Internet access than younger students. African American males had been using computer and information technology the longest which is an indication of inclusion. The paired t-test and McNemar test revealed significant perceived student increases in all skills levels. Interviews did not reveal any barriers to continued usage of the computer and information technology skills.

[A strategy of constructing the technological system for quality control of Chinese medicine based on process control and management].

PubMed

Cheng, Yi-Yu; Qian, Zhong-Zhi; Zhang, Bo-Li

2017-01-01

The current situation, bottleneck problems and severe challenges in quality control technology of Chinese Medicine (CM) are briefly described. It is presented to change the phenomenon related to the post-test as the main means and contempt for process control in drug regulation, reverse the situation of neglecting the development of process control and management technology for pharmaceutical manufacture and reconstruct the technological system for quality control of CM products. The regulation and technology system based on process control and management for controlling CM quality should be established to solve weighty realistic problems of CM industry from the root causes, including backwardness of quality control technology, weakness of quality risk control measures, poor reputation of product quality and so on. By this way, the obstacles from poor controllability of CM product quality could be broken. Concentrating on those difficult problems and weak links in the technical field of CM quality control, it is proposed to build CMC (Chemistry, Manufacturing and Controls) regulation for CM products with Chinese characteristics and promote the regulation international recognition as soon as possible. The CMC technical framework, which is clinical efficacy-oriented, manufacturing manner-centered and process control-focused, was designed. To address the clinical characteristics of traditional Chinese medicine (TCM) and the production feature of CM manufacture, it is suggested to establish quality control engineering for CM manufacturing by integrating pharmaceutical analysis, TCM chemistry, TCM pharmacology, pharmaceutical engineering, control engineering, management engineering and other disciplines. Further, a theoretical model of quality control engineering for CM manufacturing and the methodology of digital pharmaceutical engineering are proposed. A technology pathway for promoting CM standard and realizing the strategic goal of CM internationalization is elaborated. Copyright© by the Chinese Pharmaceutical Association.

Bringing Superconductor Digital Technology to the Market Place

NASA Astrophysics Data System (ADS)

Nisenoff, Martin

The unique properties of superconductivity can be exploited to provide the ultimate in electronic technology for systems such as ultra-precise analogue-to-digital and digital-to-analogue converters, precise DC and AC voltage standards, ultra high speed logic circuits and systems (both digital and hybrid analogue-digital systems), and very high throughput network routers and supercomputers which would have superior electrical performance at lower overall electrical power consumption compared to systems with comparable performance which are fabricated using conventional room temperature technologies. This potential for high performance electronics with reduced power consumption would have a positive impact on slowing the increase in the demand for electrical utility power by the information technology community on the overall electrical power grid. However, before this technology can be successfully brought to the commercial market place, there must be an aggressive investment of resources and funding to develop the required infrastructure needed to yield these high performance superconductor systems, which will be reliable and available at low cost. The author proposes that it will require a concerted effort by the superconductor and cryogenic communities to bring this technology to the commercial market place or make it available for widespread use in scientific instrumentation.

Development of Shunt-Type Three-Phase Active Power Filter with Novel Adaptive Control for Wind Generators

PubMed Central

2015-01-01

This paper proposes a new adaptive filter for wind generators that combines instantaneous reactive power compensation technology and current prediction controller, and therefore this system is characterized by low harmonic distortion, high power factor, and small DC-link voltage variations during load disturbances. The performance of the system was first simulated using MATLAB/Simulink, and the possibility of an adaptive digital low-pass filter eliminating current harmonics was confirmed in steady and transient states. Subsequently, a digital signal processor was used to implement an active power filter. The experimental results indicate, that for the rated operation of 2 kVA, the system has a total harmonic distortion of current less than 5.0% and a power factor of 1.0 on the utility side. Thus, the transient performance of the adaptive filter is superior to the traditional digital low-pass filter and is more economical because of its short computation time compared with other types of adaptive filters. PMID:26451391

Development of Shunt-Type Three-Phase Active Power Filter with Novel Adaptive Control for Wind Generators.

PubMed

Chen, Ming-Hung

2015-01-01

This paper proposes a new adaptive filter for wind generators that combines instantaneous reactive power compensation technology and current prediction controller, and therefore this system is characterized by low harmonic distortion, high power factor, and small DC-link voltage variations during load disturbances. The performance of the system was first simulated using MATLAB/Simulink, and the possibility of an adaptive digital low-pass filter eliminating current harmonics was confirmed in steady and transient states. Subsequently, a digital signal processor was used to implement an active power filter. The experimental results indicate, that for the rated operation of 2 kVA, the system has a total harmonic distortion of current less than 5.0% and a power factor of 1.0 on the utility side. Thus, the transient performance of the adaptive filter is superior to the traditional digital low-pass filter and is more economical because of its short computation time compared with other types of adaptive filters.

The interactive digital video interface

NASA Technical Reports Server (NTRS)

Doyle, Michael D.

1989-01-01

A frequent complaint in the computer oriented trade journals is that current hardware technology is progressing so quickly that software developers cannot keep up. A example of this phenomenon can be seen in the field of microcomputer graphics. To exploit the advantages of new mechanisms of information storage and retrieval, new approaches must be made towards incorporating existing programs as well as developing entirely new applications. A particular area of need is the correlation of discrete image elements to textural information. The interactive digital video (IDV) interface embodies a new concept in software design which addresses these needs. The IDV interface is a patented device and language independent process for identifying image features on a digital video display and which allows a number of different processes to be keyed to that identification. Its capabilities include the correlation of discrete image elements to relevant text information and the correlation of these image features to other images as well as to program control mechanisms. Sophisticated interrelationships can be set up between images, text, and program control mechanisms.

Seeing Music--Hearing Art

ERIC Educational Resources Information Center

Stephens, Pam

2007-01-01

In this article, the author explores the digital artwork of Brian Evans, a composer-artist who creates visualizations of sound. Through the years Evans' love for music and visual art led him to explore ways to work concurrently with image and sound. Digital technology proved to be such a means. Digital technology is based upon the transcription of…

Colloquium: Digital Technologies--Help or Hindrance for the Humanities?

ERIC Educational Resources Information Center

Barker, Elton; Bissell, Chris; Hardwick, Lorna; Jones, Allan; Ridge, Mia; Wolffe, John

2012-01-01

This article offers reflections arising from a recent colloquium at the Open University on the implications of the development of digital humanities for research in arts disciplines, and also for their interactions with computing and technology. Particular issues explored include the ways in which the digital turn in humanities research is also a…

Digitizing Technologies for Preservation. SPEC Kit 214.

ERIC Educational Resources Information Center

Kellerman, L. Suzanne, Comp.; Wilson, Rebecca, Comp.

The Association of Research Libraries distributed a survey to its 119 member libraries to assess the use of state-of-the-art digital technologies as a preservation method. Libraries were asked to report detailed data on all projects designed specifically to: (1) enhance images of faded or brittle originals, (2) provide access to digital images…

A Review of Digital Addiction: A Call for Safety Education

ERIC Educational Resources Information Center

Rugai, Joseph; Hamiliton-Ekeke, Joy-Telu

2016-01-01

In reviewing digital addiction, this paper recognized that digital technology has been useful in various spheres of life and the reach is undeniable, with an "average" user spending long hours on their phone or online daily. These hours increase as new applications are released by various technological companies. The demands of modern…

Student Adoption & Development of Digital Learning Media: Action Research and Recommended Practices

ERIC Educational Resources Information Center

Tabor, Sharon W.; Minch, Robert P.

2013-01-01

Digital technologies offer many opportunities for creating engaging course content. In this study we captured student perceptions and adoption choices related to creating and using digital media as learning tools. Podcasts, video and other media were integrated in a variety of contexts and tasks in two undergraduate information technology (IT)…

Opportunity for All? Technology and Learning in Lower-Income Families

ERIC Educational Resources Information Center

Rideout, Victoria; Katz, Vikki S.

2016-01-01

Because digital devices and the Internet have become so essential, digital inequality can exacerbate educational and economic inequality as well. Therefore, it is critical to understand how low- and moderate-income families in the U.S. are engaging digital technologies and how they perceive the opportunities--and potential risks-- that these…

Literary Education and Digital Learning: Methods and Technologies for Humanities Studies

ERIC Educational Resources Information Center

van Peer, Willie, Ed.; Zyngier, Sonia, Ed.; Viana, Vander, Ed.

2010-01-01

Today's popularization of modern technologies has allowed literature specialists to access an array of new opportunities in the digital medium, which have brought about an equal number of challenges and questions. This book provides insight into the most relevant issues in literary education and digital learning. This unique reference fills a gap…

Digital Storytelling in Writing: A Case Study of Student Teacher Attitudes toward Teaching with Technology

ERIC Educational Resources Information Center

Bumgarner, Barri L.

2012-01-01

This case study investigated how preservice teachers taught digital storytelling to students who often possessed more technology skills than the teachers. During the spring semester of 2011, two secondary-level language arts teaching interns and their cooperating teachers taught a digital storytelling project. The participants and their students…

Access to Technology in Transnational Social Fields: Simultaneity and Digital Literacy Socialization of Adult Immigrants

ERIC Educational Resources Information Center

Nogueron-Liu, Silvia

2013-01-01

Some studies of technology use by immigrants have explored the role of digital media in their maintenance of affiliations with their nations of origin. However, the potential for transnational social networks to serve as "resources" that facilitate digital literacy socialization for adult immigrant learners remains unexplored. In this…

Student and Teacher Use of Technology at the University Level

ERIC Educational Resources Information Center

Gobel, Peter; Kano, Makimi

2013-01-01

"Digital Native" and "Digital Immigrant" are terms, popularized by Prensky (2001), to describe those born either before, or in the digital era (i.e. after 1980). In recent years, this dichotomy has been used to raise awareness of differences in technology usage and what these differences may mean for education. The present…

Digital Literacy and New Technological Perspectives

ERIC Educational Resources Information Center

Feola, Elvia Ilaria

2016-01-01

This paper aims to reflect on the implications and challenges that experts in the field have to deal with when you want to evaluate the performance in the use of digital technologies in teaching. The argument stems from a contextual and social assessment, and then proceeds to an application and methodological connotation of digital literacy…

Through the Teacher's Eyes: Unpacking the TPACK of Digital Fabrication Integration in Middle School Language Arts

ERIC Educational Resources Information Center

Smith, Shaunna

2013-01-01

Digital fabrication consists of manufacturing design technology that is used to facilitate the creation of physical objects. Existing research suggests digital fabrication technology can inspire student creativity and innovation in mathematics and science. However, there is a lack of research that informs teacher education by identifying practical…

Empowering Student Voice through Interactive Design and Digital Making

ERIC Educational Resources Information Center

Kim, Yanghee; Searle, Kristin

2017-01-01

Over the last two decades online technology and digital media have provided space for students to participate and express their voices. This paper further explores how new digital technologies, such as humanoid robots and wearable electronics, can be used to offer additional spaces where students' voices are heard. In these spaces, young students…

Using TPCK with Digital Storytelling to Investigate Contemporary Issues in Educational Technology

ERIC Educational Resources Information Center

Maddin, Ellen

2012-01-01

Digital storytelling is recognized as a motivating instructional approach that engages students in critical thinking and reflective learning. Technology tools that support digital storytelling are readily available and much easier to use today than they were in years past. The convergence of these factors has facilitated the inclusion of digital…

Visual Literacy and the Digital Native: An Examination of the Millennial Learner

ERIC Educational Resources Information Center

Brumberger, Eva

2011-01-01

The so-called millennial learners who currently populate college classrooms are purportedly digital natives whose repeated exposure to a host of new technologies has allegedly resulted in enhanced skills in several areas, including those related to technology and visual communication. By extension, the argument has been made that digital natives…

Digital Preservation and Deep Infrastructure; Dublin Core Metadata Initiative Progress Report and Workplan for 2002; Video Gaming, Education and Digital Learning Technologies: Relevance and Opportunities; Digital Collections of Real World Objects; The MusArt Music-Retrieval System: An Overview; eML: Taking Mississippi Libraries into the 21st Century.

ERIC Educational Resources Information Center

Granger, Stewart; Dekkers, Makx; Weibel, Stuart L.; Kirriemuir, John; Lensch, Hendrik P. A.; Goesele, Michael; Seidel, Hans-Peter; Birmingham, William; Pardo, Bryan; Meek, Colin; Shifrin, Jonah; Goodvin, Renee; Lippy, Brooke

2002-01-01

One opinion piece and five articles in this issue discuss: digital preservation infrastructure; accomplishments and changes in the Dublin Core Metadata Initiative in 2001 and plans for 2002; video gaming and how it relates to digital libraries and learning technologies; overview of a music retrieval system; and the online version of the…

Update on new technologies in digital mammography

PubMed Central

Patterson, Stephanie K; Roubidoux, Marilyn A

2014-01-01

Despite controversy regarding mammography’s efficacy, it continues to be the most commonly used breast cancer-screening modality. With the development of digital mammography, some improved benefit has been shown in women with dense breast tissue. However, the density of breast tissue continues to limit the sensitivity of conventional mammography. We discuss the development of some derivative digital technologies, primarily digital breast tomosynthesis, and their strengths, weaknesses, and potential patient impact. PMID:25152634

Digital storytelling: an innovative technological approach to nursing education.

PubMed

Price, Deborah M; Strodtman, Linda; Brough, Elizabeth; Lonn, Steven; Luo, Airong

2015-01-01

This study investigated the impact of using digital stories in promoting deeper understanding in nursing students about palliative care concepts. Students (N = 134) created a 5-minute narrated digital story utilizing VoiceThread technology that synthesized and applied knowledge that had been presented in class and course readings. Postsurvey and focus group evaluation data revealed that through the writing and sharing of digital stories, students embraced the personal and complex nature of palliative care.

Storytelling in the digital world: achieving higher-level learning objectives.

PubMed

Schwartz, Melissa R

2012-01-01

Nursing students are not passive media consumers but instead live in a technology ecosystem where digital is the language they speak. To prepare the next generation of nurses, educators must incorporate multiple technologies to improve higher-order learning. The author discusses the evolution and use of storytelling as part of the digital world and how digital stories can be aligned with Bloom's Taxonomy so that students achieve higher-level learning objectives.

Evaluation of an F100 multivariable control using a real-time engine simulation

NASA Technical Reports Server (NTRS)

Szuch, J. R.; Soeder, J. F.; Skira, C.

1977-01-01

The control evaluated has been designed for the F100-PW-100 turbofan engine. The F100 engine represents the current state-of-the-art in aircraft gas turbine technology. The control makes use of a multivariable, linear quadratic regulator. The evaluation procedure employed utilized a real-time hybrid computer simulation of the F100 engine and an implementation of the control logic on the NASA LeRC digital computer/controller. The results of the evaluation indicated that the control logic and its implementation will be capable of controlling the engine throughout its operating range.