Highlighting landslides and other geomorphological features using sediment connectivity maps

NASA Astrophysics Data System (ADS)

Bossi, Giulia; Crema, Stefano; Cavalli, Marco; Marcato, Gianluca; Pasuto, Alessandro

2016-04-01

Landslide identification is usually made through interpreting geomorphological features in the field or with remote sensing imagery. In recent years, airborne laser scanning (LiDAR) has enhanced the potentiality of geomorphological investigations by providing a detailed and diffuse representation of the land surface. The development of algorithms for geomorphological analysis based on LiDAR derived high-resolution Digital Terrain Models (DTMs) is increasing. Among them, the sediment connectivity index (IC) has been used to quantify sediment dynamics in alpine catchments. In this work, maps of the sediment connectivity index are used for detecting geomorphological features and processes not exclusively related to water-laden processes or debris flows. The test area is located in the upper Passer Valley in South Tyrol (Italy). Here a 4 km2 Deep-seated Gravitational Slope Deformation (DGSD) with several secondary phenomena has been studied for years. The connectivity index was applied to a well-known study area in order to evaluate its effectiveness as an interpretative layer to assist geomorphological analysis. Results were cross checked with evidence previously identified by means of in situ investigations, photointerpretation and monitoring data. IC was applied to a 2.5 m LiDAR derived DTM using two different scenarios in order to test their effectiveness: i) IC derived on the hydrologically correct DTM; ii) IC derived on the original DTM. In the resulting maps a cluster of low-connectivity areas appears as the deformation of the DGSD induce a convexity in the central part of the phenomenon. The double crests, product of the sagging of the landslide, are extremely evident since in those areas the flow directions diverge from the general drainage pattern, which is directed towards the valley river. In the crown area a rock-slab that shows clear evidence of incumbent detachment is clearly highlighted since the maps emphasize the presence of traction trenches and reverse slope. In the second scenario, rockfall activity is more evident since the collapse path induces scars in the slope that locally are identified as flow paths, moreover the presence of the block remnants creates an obstruction (i.e., a sink) for the algorithm. On the other hand, the presence of a smaller rotational landslide at the toe of the DGSD is more detectable in the map derived from the first scenario that shows a rapid change in slope together with a high drainage concentration. An integrated approach that assists the geomorphologic analysis based on aerial images and shaded relief maps with an IC map has proven to be a valuable tool as it allows to highlight different gravitational processes.

Geomorphological hazards and environmental impact: Assessment and mapping

NASA Astrophysics Data System (ADS)

Panizza, Mario

In five sections the author develops the methods for the integration of geomorphological concepts into Environmental Impact and Mapping. The first section introduces the concepts of Impact and Risk through the relationships between Geomorphological Environment and Anthropical Element. The second section proposes a methodology for the determination of Geomorphological Hazard and the identification of Geomorphological Risk. The third section synthesizes the procedure for the compilation of a Geomorphological Hazards Map. The fourth section outlines the concepts of Geomorphological Resource Assessment for the analysis of the Environmental Impact. The fifth section considers the contribution of geomorphological studies and mapping in the procedure for Environmental Impact Assessment.

A preliminary geomorphological map from the Múlajökull drumlin field, Iceland

NASA Astrophysics Data System (ADS)

Jonsson, S. A.; Schomacker, A.; Benediktsson; Johnson, M.; Ingolfsson, O.

2012-12-01

The drumlin field in front of Múlajökull, a surge-type, outlet glacier from Hofsjökull in Iceland, is the only known active drumlin field (Johnson et al., 2010). The aim of this study is to further explore the distribution and formation of drumlins and drumlin fields in a modern glacial environment. We use data from Digital Elevation Models (DEMs), aerial imagery and field mapping. Here we present a preliminary geomorphological map based on remote sensing and fieldwork in 2010 and 2011. Geomorphological mapping of the drumlin field both with DEMs and ground proofing has revealed over 100 drumlins and a number of drumlinized ridges. The drumlins furthest from the present ice margin are broader and have lower relief than those closer to the ice. We suggest that this reflects an evolution of the drumlin form during recurrent surging. The drumlins farther away from the ice have experienced fewer surges than those that have just been uncovered due to present retreat of the ice margin. During successive surges, the drumlins become narrower and develop a higher relief. Reference: Johnson, M.D., Schomacker, A., Benediktsson, Í. Ö., Geiger, A. J., Ferguson, A. and Ingólfsson, Ó. 2010, Active drumlin field revealed at the margin of Múlajökull, Iceland: A surge-type glacier: Geology v. 38, p. 943-946.

Multi-Scale and Object-Oriented Analysis for Mountain Terrain Segmentation and Geomorphological Assessment

NASA Astrophysics Data System (ADS)

Marston, B. K.; Bishop, M. P.; Shroder, J. F.

2009-12-01

Digital terrain analysis of mountain topography is widely utilized for mapping landforms, assessing the role of surface processes in landscape evolution, and estimating the spatial variation of erosion. Numerous geomorphometry techniques exist to characterize terrain surface parameters, although their utility to characterize the spatial hierarchical structure of the topography and permit an assessment of the erosion/tectonic impact on the landscape is very limited due to scale and data integration issues. To address this problem, we apply scale-dependent geomorphometric and object-oriented analyses to characterize the hierarchical spatial structure of mountain topography. Specifically, we utilized a high resolution digital elevation model to characterize complex topography in the Shimshal Valley in the Western Himalaya of Pakistan. To accomplish this, we generate terrain objects (geomorphological features and landform) including valley floors and walls, drainage basins, drainage network, ridge network, slope facets, and elemental forms based upon curvature. Object-oriented analysis was used to characterize object properties accounting for object size, shape, and morphometry. The spatial overlay and integration of terrain objects at various scales defines the nature of the hierarchical organization. Our results indicate that variations in the spatial complexity of the terrain hierarchical organization is related to the spatio-temporal influence of surface processes and landscape evolution dynamics. Terrain segmentation and the integration of multi-scale terrain information permits further assessment of process domains and erosion, tectonic impact potential, and natural hazard potential. We demonstrate this with landform mapping and geomorphological assessment examples.

Automating the implementation of an equilibrium profile model for glacier reconstruction in a GIS environment

NASA Astrophysics Data System (ADS)

Frew, Craig R.; Pellitero, Ramón; Rea, Brice R.; Spagnolo, Matteo; Bakke, Jostein; Hughes, Philip D.; Ivy-Ochs, Susan; Lukas, Sven; Renssen, Hans; Ribolini, Adriano

2014-05-01

Reconstruction of glacier equilibrium line altitudes (ELAs) associated with advance stages of former ice masses is widely used as a tool for palaeoclimatic reconstruction. This requires an accurate reconstruction of palaeo-glacier surface hypsometry, based on mapping of available ice-marginal landform evidence. Classically, the approach used to define ice-surface elevations, using such evidence, follows the 'cartographic method', whereby contours are estimated based on an 'understanding' of the typical surface form of contemporary ice masses. This method introduces inherent uncertainties in the palaeoclimatic interpretation of reconstructed ELAs, especially where the upper limits of glaciation are less well constrained and/or the age of such features in relation to terminal moraine sequences is unknown. An alternative approach is to use equilibrium profile models to define ice surface elevations. Such models are tuned, generally using basal shear stress, in order to generate an ice surface that reaches 'target elevations' defined by geomorphology. In areas where there are no geomorphological constraints for the former ice surface, the reconstruction is undertaken using glaciologiaclly representative values for basal shear stress. Numerical reconstructions have been shown to produce glaciologically "realistic" ice surface geometries, allowing for more objective and robust comparative studies at local to regional scales. User-friendly tools for the calculation of equilibrium profiles are presently available in the literature. Despite this, their use is not yet widespread, perhaps owing to the difficult and time consuming nature of acquiring the necessary inputs from contour maps or digital elevation models. Here we describe a tool for automatically reconstructing palaeo-glacier surface geometry using an equilibrium profile equation implemented in ArcGIS. The only necessary inputs for this tool are 1) a suitable digital elevation model and 2) mapped outlines of the former glacier terminus position (usually a frontal moraine system) and any relevant geomorphological constraints on ice surface elevation (e.g. lateral moraines, trimlines etc.). This provides a standardised method for glacier reconstruction that can be applied rapidly and systematically to large geomorphological datasets.

Landslides in the Central Coalfield (Cantabrian Mountains, NW Spain): Geomorphological features, conditioning factors and methodological implications in susceptibility assessment

NASA Astrophysics Data System (ADS)

Domínguez-Cuesta, María José; Jiménez-Sánchez, Montserrat; Berrezueta, Edgar

2007-09-01

A geomorphological study focussing on slope instability and landslide susceptibility modelling was performed on a 278 km 2 area in the Nalón River Basin (Central Coalfield, NW Spain). The methodology of the study includes: 1) geomorphological mapping at both 1:5000 and 1:25,000 scales based on air-photo interpretation and field work; 2) Digital Terrain Model (DTM) creation and overlay of geomorphological and DTM layers in a Geographical Information System (GIS); and 3) statistical treatment of variables using SPSS and development of a logistic regression model. A total of 603 mass movements including earth flow and debris flow were inventoried and were classified into two groups according to their size. This study focuses on the first group with small mass movements (10 0 to 10 1 m in size), which often cause damage to infrastructures and even victims. The detected conditioning factors of these landslides are lithology (soils and colluviums), vegetation (pasture) and topography. DTM analyses show that high instabilities are linked to slopes with NE and SW orientations, curvature values between - 6 and - 0.7, and slope values from 16° to 30°. Bedrock lithology (Carboniferous sandstone and siltstone), presence of Quaternary soils and sediments, vegetation, and the topographical factors were used to develop a landslide susceptibility model using the logistic regression method. Application of "zoom method" allows us to accurately detect small mass movements using a 5-m grid cell data even if geomorphological mapping is done at a 1:25,000 scale.

Extraction and Validation of Geomorphological Features from EU-DEM in The Vicinity of the Mygdonia Basin, Northern Greece

NASA Astrophysics Data System (ADS)

Mouratidis, Antonios; Karadimou, Georgia; Ampatzidis, Dimitrios

2017-12-01

The European Union Digital Elevation Model (EU-DEM) is a relatively new, hybrid elevation product, principally based on SRTM DEM and ASTER GDEM data, but also on publically available Russian topographic maps for regions north of 60° N. More specifically, EU-DEM is a Digital Surface Model (DSM) over Europe from the Global Monitoring for Environment and Security (GMES) Reference Data Access (RDA) project - a realisation of the Copernicus (former GMES) programme, managed by the European Commission/DG Enterprise and Industry. Even if EU-DEM is indeed more reliable in terms of elevation accuracy than its constituents, it ought to be noted that it is not representative of the original elevation measurements, but is rather a secondary (mathematical) product. Therefore, for specific applications, such as those of geomorphological interest, artefacts may be induced. To this end, the purpose of this paper is to investigate the performance of EU-DEM for geomorphological applications and compare it against other available datasets, i.e. topographic maps and (almost) global DEMs such as SRTM, ASTER-GDEM and WorldDEM™. This initial investigation is carried out in Central Macedonia, Northern Greece, in the vicinity of the Mygdonia basin, which corresponds to an area of particular interest for several geoscience applications. This area has also been serving as a test site for the systematic validation of DEMs for more than a decade. Consequently, extensive elevation datasets and experience have been accumulated over the years, rendering the evaluation of new elevation products a coherent and useful exercise on a local to regional scale. In this context, relief classification, drainage basin delineation, slope and slope aspect, as well as extraction and classification of drainage network are performed and validated among the aforementioned elevation sources. The achieved results focus on qualitative and quantitative aspects of automatic geomorphological feature extraction from EU-DEM at a water basin level, with the use of Geographical Information Systems (GIS).

Topographic representation using DEMs and its applications to active tectonics research

NASA Astrophysics Data System (ADS)

Oguchi, T.; Lin, Z.; Hayakawa, Y. S.

2016-12-01

Identifying topographic deformations due to active tectonics has been a principal issue in tectonic geomorphology. It provides useful information such as whether a fault has been active during the recent past. Traditionally, field observations, conventional surveying, and visual interpretation of topographic maps, aerial photos, and satellite images were the main methods for such geomorphological investigations. However, recent studies have been utilizing digital elevation models (DEMs) to visualize and quantitatively analyze landforms. There are many advantages to the use of DEMs for research in active tectonics. For example, unlike aerial photos and satellite images, DEMs show ground conditions without vegetation and man-made objects such as buildings, permitting direct representation of tectonically deformed landforms. Recent developments and advances in airborne LiDAR also allow the fast creation of DEMs even in vegetated areas such as forested lands. In addition, DEMs enable flexible topographic visualization based on various digital cartographic and computer-graphic techniques, facilitating identification of particular landforms such as active faults. Further, recent progress in morphometric analyses using DEMs can be employed to quantitatively represent topographic characteristics, and objectively evaluate tectonic deformation and the properties of related landforms. This paper presents a review of DEM applications in tectonic geomorphology, with attention to historical development, recent advances, and future perspectives. Examples are taken mainly from Japan, a typical tectonically active country. The broader contributions of DEM-based active tectonics research to other fields, such as fluvial geomorphology and geochronology, will also be discussed.

Yangon River Geomorphology Identification and its Enviromental Imapacts Analsysi by Optical and Radar Sensing Techniques

NASA Astrophysics Data System (ADS)

Lwin, A.; Khaing, M. M.

2012-07-01

The Yangon river, also known as the Rangoon river, is about 40 km long (25miles), and flows from southern Myanmar as an outlet of the Irrawaddy (Ayeyarwady) river into the Ayeyarwady delta. The Yangon river drains the Pegu Mountains; both the Yangon and the Pathein rivers enter the Ayeyarwady at the delta. Fluvial geomorphology is based primarily on rivers of manageable dimensions. The emphasis is on geomorphology, sedimentology of Yangon river and techniques for their identification and management. Present techniques such as remote sensing have made it easier to investigate and interpret in details analysis of river geomorphology. In this paper, attempt has been made the complicated issues of geomorphology, sedimentation patterns and management of river system and evolution studied. The analysis was carried out for the impact of land use/ land cover (LULC) changes on stream flow patterns. The hydrologic response to intense, flood producing rainfall events bears the signatures of the geomorphic structure of the channel network and of the characteristic slope lengths defining the drainage density of the basin. The interpretation of the hydrologic response as the travel time distribution of a water particle randomly injected in a distributed manner across the landscape inspired many geomorphic insights. In 2008, Cyclone Nargis was seriously damaged to mangrove area and its biodiversity system in and around of Yangon river terraces. A combination of digital image processing techniques was employed for enhancement and classification process. It is observed from the study that middle infra red band (0.77mm - 0.86mm) is highly suitable for mapping mangroves. Two major classes of mangroves, dense and open mangroves were delineated from the digital data.

Identification of karst sinkholes in a forested karst landscape using airborne laser scanning data and water flow analysis

NASA Astrophysics Data System (ADS)

Hofierka, Jaroslav; Gallay, Michal; Bandura, Peter; Šašak, Ján

2018-05-01

Karst sinkholes (dolines) play an important role in a karst landscape by controlling infiltration of surficial water, air flow or spatial distribution of solar energy. These landforms also present a limiting factor for human activities in agriculture or construction. Therefore, mapping such geomorphological forms is vital for appropriate landscape management and planning. There are several mapping techniques available; however, their applicability can be reduced in densely forested areas with poor accessibility and visibility of the landforms. In such conditions, airborne laser scanning (ALS) provides means for efficient and accurate mapping of both land and landscape canopy surfaces. Taking the benefits of ALS into account, we present an innovative method for identification and evaluation of karst sinkholes based on numerical water flow modelling. The suggested method was compared to traditional techniques for sinkhole mapping which use topographic maps and digital terrain modelling. The approach based on simulation of a rainfall event very closely matched the reference datasets derived by manual inspection of the ALS digital elevation model and field surveys. However, our process-based approach provides advantage of assessing the magnitude how sinkholes influence concentration of overland water flow during extreme rainfall events. This was performed by calculating the volume of water accumulated in sinkholes during the simulated rainfall. In this way, the influence of particular sinkholes on underground geomorphological systems can be assessed. The method was demonstrated in a case study of Slovak Karst in the West Carpathians where extreme rainfalls or snow-thaw events occur annually. We identified three spatially contiguous groups of sinkholes with a different effect on overland flow concentration. These results are discussed in relation to the known underground hydrological systems.

Time-series studies of drainage pattern and morphological features along the Leitha river (Eastern Austria)

NASA Astrophysics Data System (ADS)

Zámolyi, A.; Draganits, E.; Doneus, M.; Fera, M.; Griebl, M.

2009-04-01

Geomorphologic mapping and drainage network analysis was conducted in the Southern Vienna Basin on the Leitha and Fischa rivers. The study area belongs to an active pull-apart basin between the Eastern Alps and the Carpathians that started to subside in Karpatian times (~ 17 Ma), but with still active faults, proven by fault scarps and earth quakes. The investigated rivers are important tributaries to the Danube river and run through a region that has been subject to settlement since Neoltihic times. Thus, interaction between land use, settlement pattern and river dynamics can be studied. Several datasets are integrated to perform a comprehensive overview of geomorphological, as well as river dynamic changes in the landscape. During an earlier stage of this investigation a map of paleochannel distribution including the location and shape of the paleochannels was extracted from color-infrared and RGB digital orthophotos. Based on this map the location, character and shape of palaeomeanders is studied on different georeferenced historic maps (Timár et al., 2006; Biszak et al., 2007) in order to derive a time-series study. The paleochannels extracted from the digital orthophotos show a good coincidence with the depicted rivers on the historic maps. This partly allows quite well constrained age estimates of the paleochannel sections. The investigated maps are the Walter maps, the First, Second and Third Military Survey of the Habsburg/Austro-Hungarian Empire. Mapping of the Walter maps was conducted 1754-56 (Ulbrich, 1952), the First, Second and Third Military Surveys were mapped in this area in the time-span of 1782-1785, 1819-1869, and 1872-1873, respectively (Kretschmer et al., 2004). This sequence of georeferenced historical maps allows to study only a very short time-span (1755 - 1873) compared to the geological time scale. However, the characteristics of river dynamics special for the study area can be derived and, considering certain assumptions, extrapolated to a wider time range. Within the observable time period the Leitha river preserved its meandering characteristics. Small shifts of the mean channel towards E or W can be detected. A disadvantage of the maps previous to the Third Military Survey is the lack of contour lines. On these maps, variation in terrain elevation was mapped „a la vue" and rather depicted as changes in slope of the terrain by applying hatchures showing a density increase with higher slope. This method provided a very plastic overview of changes in the terrain, but the reading of absolute or relative elevations is not possible. According to this, geomorphologic observations from these maps are constricted to the comparison of the horizontal position of elevated areas and the change of their outline. This study shows that historical maps provide an essential tool to investigate younger river dynamics and sensitively show the impact of anthropological modifications as well as active tectonics. Biszak, S., Timár, G., Molnár, G., Jankó, A. (2007): Digitized maps of the Habsburg Empire - The third military survey, Österreichisch-Ungarische Monarchie, 1869-1887, 1:75000. DVD-issue, Arcanum, Budapest. ISBN 978-963-73-7451-7 Kretschmer, I., Dörflinger, J., Wawrick, F. (2004): Österreichische Kartographie. Wiener Schiften zur Geographie und Kartographie - Band 15. Institut für Geographie und Regionalforschung der Universität Wien, Wien. Timár, G., Molnár, G., Székely, B., Biszak, S., Varga, J., Jankó, A. (2006): Digitized maps of the Habsburg Empire - The map sheets of the second military survey and their georeferenced version. Arcanum, Budapest, 59 p. ISBN 963-7374-33-7 Ulbrich K. (1952): Die Grenzkarte Ungarn-Niederösterreich von C. J. Walter (1754 - 56). Burgenländische Heimatblätter, 14, 108-121

Morphological analysis of hummocks in debris avalanche deposits using UAS-derived high-definition topographic data

NASA Astrophysics Data System (ADS)

Hayakawa, Yuichi S.; Obanawa, Hiroyuki; Yoshida, Hidetsugu; Naruhashi, Ryutaro; Okumura, Koji; Zaiki, Masumi

2016-04-01

Debris avalanche caused by sector collapse of a volcanic mountain often forms depositional landforms with characteristic surface morphology comprising hummocks. Geomorphological and sedimentological analyses of debris avalanche deposits (DAD) at the northeastern face of Mt. Erciyes in central Turkey have been performed to investigate the mechanisms and processes of the debris avalanche. The morphometry of hummocks provides an opportunity to examine the volumetric and kinematic characteristics of the DAD. Although the exact age has been unknown, the sector collapse of this DAD was supposed to have occurred in the late Pleistocene (sometime during 90-20 ka), and subsequent sediment supply from the DAD could have affected ancient human activities in the downstream basin areas. In order to measure detailed surface morphology and depositional structures of the DAD, we apply structure-from-motion multi-view stereo (SfM-MVS) photogrammetry using unmanned aerial system (UAS) and a handheld camera. The UAS, including small unmanned aerial vehicle (sUAV) and a digital camera, provides low-altitude aerial photographs to capture surface morphology for an area of several square kilometers. A high-resolution topographic data, as well as an orthorectified image, of the hummocks were then obtained from the digital elevation model (DEM), and the geometric features of the hummocks were examined. A handheld camera is also used to obtain photographs of outcrop face of the DAD along a road to support the seimentological investigation. The three-dimensional topographic models of the outcrop, with a panoramic orthorectified image projected on a vertical plane, were obtained. This data enables to effectively describe sedimentological structure of the hummock in DAD. The detailed map of the DAD is also further examined with a regional geomorphological map to be compared with other geomorphological features including fluvial valleys, terraces, lakes and active faults.

Analysis of the effects of geological and geomorphological factors on earthquake triggered landslides using artificial neural networks (ANN)

NASA Astrophysics Data System (ADS)

Kawabata, D.; Bandibas, J.

2007-12-01

The occurrence of landslide is the result of the interaction of complex and diverse environmental factors. The geomorphic and geologic features, rock types and vegetative cover are important base factors of landslide occurrence. However, determining the relationship between these factors and landslide occurrence is very difficult using conventional mathematical analysis. The use of an advanced computing technique for this kind of analysis is very important. Artificial neural network (ANN) has recently been included in the list of analytical tools for a wide range of applications in the natural sciences research fields. One of the advantages of using ANN for pattern recognition is that it can handle data at any measurement scale ranging from nominal, ordinal to linear and ratio, and any form of data distribution (Wang et al., 1995). In addition, it can easily handle qualitative variables making it widely used in integrated analysis of spatial data from multiple sources for predicting and classification. This study focuses on the definition of the relationship between geological factors and landslide occurrence using artificial neural networks. The study also focuses on the effect of the DTMs (e.g. ASTER DTM, ALSM, digitized from paper map and digital photogrammetric measurement data). The main aim of the study is to generate landslide susceptibility index map using the defined relationship using ANN. Landslide data in the Chuetsu region were used in this research. The 2004 earthquake triggered many landslides in the region. The initial results of the study showed that ANN is more accurate in defining the relationship between geological and geomorphological factors and landslide occurrence. It also determined the best combination of geological and geomorphological factors that is directly related to landslide occurrence.

Teaching Topographic Map Skills and Geomorphology Concepts with Google Earth in a One-Computer Classroom

ERIC Educational Resources Information Center

Hsu, Hsiao-Ping; Tsai, Bor-Wen; Chen, Che-Ming

2018-01-01

Teaching high-school geomorphological concepts and topographic map reading entails many challenges. This research reports the applicability and effectiveness of Google Earth in teaching topographic map skills and geomorphological concepts, by a single teacher, in a one-computer classroom. Compared to learning via a conventional instructional…

Spatial analysis of fluvial terraces in GRASS GIS accessing R functionality

NASA Astrophysics Data System (ADS)

Józsa, Edina

2017-04-01

Terrace research along the Danube is a major topic of Hungarian traditional geomorphology because of the socio-economic role of terrace surfaces and their importance in paleo-environmental reconstructions. Semi-automated mapping of fluvial landforms from a coherent digital elevation dataset allow objective analysis of hydrogeomorphic characteristics with low time and cost requirements. New results obtained with unified GIS-based algorithms can be integrated with previous findings regarding landscape evolution. The complementary functionality of GRASS GIS and R provides the possibility to develop a flexible terrain analysing tool for the delineation and quantifiable analysis of terrace remnants. Using R as an intermediate analytical environment and visualisation tool gives great added value to the algorithm, while GRASS GIS is capable of handling the large digital elevation datasets and perform the demanding computations to prepare necessary raster derivatives (Bivand, R.S. et al. 2008). The proposed terrace mapping algorithm is based on the work of Demoulin, A. et al. (2007), but it is further improved in the form of GRASS GIS script tool accessing R functionality. In the first step the hydrogeomorphic signatures of the given study site are explored and the area is divided along clearly recognizable structural-morphological boundaries.The algorithm then cuts up the subregions into parallel sections in the flow direction and determines cells potentially belonging to terrace surfaces based on local slope characteristics and a minimum area size threshold. As a result an output report is created that contains a histogram of altitudes, a swath-profile of the landscape, scatter plots to represent the relation of the relative elevations and slope values in the analysed sections and a final plot showing the longitudinal profile of the river with the determined height ranges of terrace levels. The algorithm also produces a raster map of extracted terrace remnants. From this dataset it is possible to interpolate a new digital elevation model approximating the former terraced valley surface using the Ordinary Kriging method (Troiani, F. and Della Seta, M. 2011). The applicability of the algorithm was tested on the northern foreland of Gerecse Mountains, an antecedent valley section of the Danube, with terrace remnants expected in 6 to 8 altitude ranges. Methodological issues arising from determining the optimal threshold values were explored using an artificial hillslope model, while the terrace profiles and terrace-top surfaces raster generated from the digital elevation model were validated with the previous findings of traditional geomorphological surveys. This research was supported by the Human Capacities Grant Management Office and the Hungarian Ministry of Human Capacities in the framework of the NTP-NFTÖ-16 project. References: Bivand, R.S. et al. (2008). Applied Spatial Data Analysis with R. New York: Springer. 378 p. Demoulin, A. et al. (2007). An automated method to extract fluvial terraces from digital elevation models: The Vesdre valley, a case study in eastern Belgium. - Geomorphology 91 (1-2): 51-64. Troiani, E. and Della Seta, M. (2011). Geomorphological response of fluvial and coastal terraces to Quaternary tectonics and climate as revealed by geostatistical topographic analysis. - Earth Surface Processes and Landforms 36: 1193-1208.

Techniques, problems and uses of mega-geomorphological mapping

NASA Technical Reports Server (NTRS)

Embleton, C.

1985-01-01

A plea for a program of global geomorphological mapping based on remote sensing data is presented. It is argued that the program is a necessary step in bringing together the rapidly evolving concepts of plate tectonics with the science of geomorphology. Geomorphologists are urged to bring temporal scales into their subject and to abandon their recent isolation from tectonics and geological history. It is suggested that a start be made with a new geomorphological map of Europe, utilizing the latest space technology.

Geomorphology subprogram: Geomorphological map of Occidental region of Bolivia, utilizing ERTS imagery

NASA Technical Reports Server (NTRS)

Brockmann, C. E. (Principal Investigator); Suarez, M. M.

1973-01-01

The author has identified the following significant results. Due to the receipt of ERTS-1 imagery, Bolivia will have for the first time a geomorphological map at a scale of 1:100,000. Now the researcher and the student will be able to compare the distribution of the existing shapes of the country, which have been modelled by diverse processes, factors, and agents. This geomorphological information will be very useful in its application to mining, especially alluvial beds, engineering work, and other geological studies. This map is divided into ten geomorphological units which coincide with the geostructural units of the western region of the country.

Geological, geomorphological, facies and allostratigraphic maps of the Eberswalde fan delta

NASA Astrophysics Data System (ADS)

Pondrelli, M.; Rossi, A. P.; Platz, T.; Ivanov, A.; Marinangeli, L.; Baliva, A.

2011-09-01

Geological, facies, geomorphological and allostratigraphic map of the Eberswalde fan delta area are presented. The Eberswalde fan delta is proposed as a sort of prototype area to map sedimentary deposits, because of its excellent data coverage and its variability in depositional as well as erosional morphologies and sedimentary facies. We present a report to distinguish different cartographic products implying an increasing level of interpretation. The geological map - in association with the facies map - represents the most objective mapping product. Formations are distinguished on the basis of objectively observable parameters: texture, color, sedimentary structures and geographic distribution. Stratigraphic relations are evaluated using Steno's principles. Formations can be interpreted in terms of depositional environment, but an eventual change of the genetic interpretation would not lead to a change in the geological map. The geomorphological map is based on the data represented in the geological map plus the association of the morphological elements, in order to infer the depositional sub-environments. As a consequence, it is an interpretative map focused on the genetic reconstruction. The allostratigraphic map is based on the morphofacies analysis - expressed by the geomorphological map - and by the recognition of surfaces which reflect allogenic controls, such as water level fluctuations: unconformities, erosional truncations and flooding surfaces. As a consequence, this is an even more interpretative map than the geomorphological one, since it focuses on the control on the sedimentary systems. Geological maps represent the most suitable cartographic product for a systematic mapping, which can serve as a prerequisite for scientific or landing site analyses. Geomorphological and allostratographic maps are suitable tools to broaden scientific analysis or to provide scientific background to landing site selection.

Mapping coastal morphodynamics with geospatial techniques, Cape Henry, Virginia, USA

NASA Astrophysics Data System (ADS)

Allen, Thomas R.; Oertel, George F.; Gares, Paul A.

2012-01-01

The advent and proliferation of digital terrain technologies have spawned concomitant advances in coastal geomorphology. Airborne topographic Light Detection and Ranging (LiDAR) has stimulated a renaissance in coastal mapping, and field-based mapping techniques have benefitted from improvements in real-time kinematic (RTK) Global Positioning System (GPS). Varied methodologies for mapping suggest a need to match geospatial products to geomorphic forms and processes, a task that should consider product and process ontologies from each perspective. Towards such synthesis, coastal morphodynamics on a cuspate foreland are reconstructed using spatial analysis. Sequential beach ridge and swale topography are mapped using photogrammetric spot heights and airborne LiDAR data and integrated with digital bathymetry and large-scale vector shoreline data. Isobaths from bathymetric charts were digitized to determine slope and toe depth of the modern shoreface and a reconstructed three-dimensional antecedent shoreface. Triangulated irregular networks were created for the subaerial cape and subaqueous shoreface models of the cape beach ridges and sets for volumetric analyses. Results provide estimates of relative age and progradation rate and corroborate other paleogeologic sea-level rise data from the region. Swale height elevations and other measurements quantifiable in these data provide several parameters suitable for studying coastal geomorphic evolution. Mapped paleoshorelines and volumes suggest the Virginia Beach coastal compartment is related to embryonic spit development from a late Holocene shoreline located some 5 km east of the current beach.

Shuttle imaging radar-C science plan

NASA Technical Reports Server (NTRS)

1986-01-01

The Shuttle Imaging Radar-C (SIR-C) mission will yield new and advanced scientific studies of the Earth. SIR-C will be the first instrument to simultaneously acquire images at L-band and C-band with HH, VV, HV, or VH polarizations, as well as images of the phase difference between HH and VV polarizations. These data will be digitally encoded and recorded using onboard high-density digital tape recorders and will later be digitally processed into images using the JPL Advanced Digital SAR Processor. SIR-C geologic studies include cold-region geomorphology, fluvial geomorphology, rock weathering and erosional processes, tectonics and geologic boundaries, geobotany, and radar stereogrammetry. Hydrology investigations cover arid, humid, wetland, snow-covered, and high-latitude regions. Additionally, SIR-C will provide the data to identify and map vegetation types, interpret landscape patterns and processes, assess the biophysical properties of plant canopies, and determine the degree of radar penetration of plant canopies. In oceanography, SIR-C will provide the information necessary to: forecast ocean directional wave spectra; better understand internal wave-current interactions; study the relationship of ocean-bottom features to surface expressions and the correlation of wind signatures to radar backscatter; and detect current-system boundaries, oceanic fronts, and mesoscale eddies. And, as the first spaceborne SAR with multi-frequency, multipolarization imaging capabilities, whole new areas of glaciology will be opened for study when SIR-C is flown in a polar orbit.

Applications of Skylab EREP photographs to mapping landforms and environmental geomorphology in the Great Plains and Midwest

NASA Technical Reports Server (NTRS)

Morrison, R. B.; Lineback, J. A.; Fuller, H. K.; Rinkenberger, R. K.

1975-01-01

The following evaluations of Skylab photographs were undertaken: (1) the 1290 Skylab S190A and S190B photographs of Illinois, Iowa, Kansas, Missouri, Nebraska, and South Dakota were evaluated in detail in terms of coverage, cloud cover, photographic quality, endlap, detectability of roads and stereorelief, and utility for geomorphologic mapping, and (2) the utility of the Skylab photos were tested for interpretive analytic mapping of geomorphologic features over large areas representative of different parts of this region. Photointerpretative maps of analytic geomorphology were obtained for various test areas representative of the varied landscapes in the region. These maps are useful for regional land-use planning, ground-water exploration, and other environmental geomorphologic-geologic applications. Compared with LANDSAT-1 MSS images, Skylab photos afford almost as extensive overviews of large areas but in considerably greater detail, and for many SL photos, moderate stereorelief. However, repetitive multiseasonal, cloud-free coverage by high-quality photos is very limited and many areas have no coverage at all.

The Reference Elevation Model of Antarctica (REMA): A High Resolution, Time-Stamped Digital Elevation Model for the Antarctic Ice Sheet

NASA Astrophysics Data System (ADS)

Howat, I.; Noh, M. J.; Porter, C. C.; Smith, B. E.; Morin, P. J.

2017-12-01

We are creating the Reference Elevation Model of Antarctica (REMA), a continuous, high resolution (2-8 m), high precision (accuracy better than 1 m) reference surface for a wide range of glaciological and geodetic applications. REMA will be constructed from stereo-photogrammetric Digital Surface Models (DSM) extracted from pairs of submeter resolution DigitalGlobe satellite imagery and vertically registred to precise elevations from near-coincident airborne LiDAR, ground-based GPS surveys and Cryosat-2 radar altimetry. Both a seamless mosaic and individual, time-stamped DSM strips, collected primarily between 2012 and 2016, will be distributed to enable change measurement. These data will be used for mapping bed topography from ice thickness, measuring ice thickness changes, constraining ice flow and geodynamic models, mapping glacial geomorphology, terrain corrections and filtering of remote sensing observations, and many other science tasks. Is will also be critical for mapping ice traverse routes, landing sites and other field logistics planning. REMA will also provide a critical elevation benchmark for future satellite altimetry missions including ICESat-2. Here we report on REMA production progress, initial accuracy assessment and data availability.

Geomorphologic Map of Titan's Polar Terrains

NASA Astrophysics Data System (ADS)

Birch, S. P. D.; Hayes, A. G.; Malaska, M. J.; Lopes, R. M. C.; Schoenfeld, A.; Williams, D. A.

2016-06-01

Titan's lakes and seas contain vast amounts of information regarding the history and evolution of Saturn's largest moon. To understand this landscape, we created a geomorphologic map, and then used our map to develop an evolutionary model.

Assessing the accuracy of the Second Military Survey for the Doren Landslide (Vorarlberg, Austria)

NASA Astrophysics Data System (ADS)

Zámolyi, András.; Székely, Balázs; Biszak, Sándor

2010-05-01

Reconstruction of the early and long-term evolution of landslide areas is especially important for determining the proportion of anthropogenic influence on the evolution of the region affected by mass movements. The recent geologic and geomorphological setting of the prominent Doren landslide in Vorarlberg (Western Austria) has been studied extensively by various research groups and civil engineering companies. Civil aerial imaging of the area dates back to the 1950's. Modern monitoring techniques include aerial imaging as well as airborne and terrestrial laser scanning (LiDAR) providing us with almost yearly assessment of the changing geomorphology of the area. However, initiation of the landslide occurred most probably earlier than the application of these methods, since there is evidence that the landslide was already active in the 1930's. For studying the initial phase of landslide formation one possibility is to get back on information recorded on historic photographs or historic maps. In this case study we integrated topographic information from the map sheets of the Second Military Survey of the Habsburg Empire that was conducted in Vorarlberg during the years 1816-1821 (Kretschmer et al., 2004) into a comprehensive GIS. The region of interest around the Doren landslide was georeferenced using the method of Timár et al. (2006) refined by Molnár (2009) thus providing a geodetically correct positioning and the possibility of matching the topographic features from the historic map with features recognized in the LiDAR DTM. The landslide of Doren is clearly visible in the historic map. Additionally, prominent geomorphologic features such as morphological scarps, rills and gullies, mass movement lobes and the course of the Weißach rivulet can be matched. Not only the shape and character of these elements can be recognized and matched, but also the positional accuracy is adequate for geomorphological studies. Since the settlement structure is very stable in the region, and in the historical map sheets the individual buildings were also mapped, it is possible to match several buildings with their present-day counterparts. We used matched geomorphologic features and buildings for deriving RMSE values, which range around 26 m. Orientation of major scarps and conspicuous geomorphologic features derived from the historic map and on the LiDAR DTM show a good correlation which confirms the long-term existence of these elements. Evidence from field geologic measurements provide the possible link of these elements to structural geologic features. Furthermore there is strong indication for that the landslide had been in a somewhat other state in the 19th century and the scarp retreat rate could have increased in the second half of the 20th century. Kretschmer, I., Dörflinger, J., Wawrick, F. (2004): Österreichische Kartographie. Wiener Schiften zur Geographie und Kartographie - Band 15. Institut für Geographie und Regionalforschung der Universität Wien, Wien. Molnár, G. (2009): Making a georeferenced mosaic of historical map series using constrained polynomial fit. Geophysical Research Abstracts, 11, ISSN 10297006. Timár, G., Molnár, G., Székely, B., Biszak, S., Varga, J., Jankó, A. (2006): Digitized maps of the Habsburg Empire - The map sheets of the second military survey and their georeferenced version. Arcanum, Budapest, 59 p. ISBN 963-7374-33-7

Digital Bedrock Compilation: A Geodatabase Covering Forest Service Lands in California

NASA Astrophysics Data System (ADS)

Elder, D.; de La Fuente, J. A.; Reichert, M.

2010-12-01

This digital database contains bedrock geologic mapping for Forest Service lands within California. This compilation began in 2004 and the first version was completed in 2005. Second publication of this geodatabase was completed in 2010 and filled major gaps in the southern Sierra Nevada and Modoc/Medicine Lake/Warner Mountains areas. This digital map database was compiled from previously published and unpublished geologic mapping, with source mapping and review from California Geological Survey, the U.S. Geological Survey and others. Much of the source data was itself compilation mapping. This geodatabase is huge, containing ~107,000 polygons and ~ 280,000 arcs. Mapping was compiled from more than one thousand individual sources and covers over 41,000,000 acres (~166,000 km2). It was compiled from source maps at various scales - from ~ 1:4,000 to 1:250,000 and represents the best available geologic mapping at largest scale possible. An estimated 70-80% of the source information was digitized from geologic mapping at 1:62,500 scale or better. Forest Service ACT2 Enterprise Team compiled the bedrock mapping and developed a geodatabase to store this information. This geodatabase supports feature classes for polygons (e.g, map units), lines (e.g., contacts, boundaries, faults and structural lines) and points (e.g., orientation data, structural symbology). Lookup tables provide detailed information for feature class items. Lookup/type tables contain legal values and hierarchical groupings for geologic ages and lithologies. Type tables link coded values with descriptions for line and point attributes, such as line type, line location and point type. This digital mapping is at the core of many quantitative analyses and derivative map products. Queries of the database are used to produce maps and to quantify rock types of interest. These include the following: (1) ultramafic rocks - where hazards from naturally occurring asbestos are high, (2) granitic rocks - increased erosion hazards, (3) limestone, chert, sedimentary rocks - paleontological resources (Potential Fossil Yield Classification maps), (4) calcareous rocks (cave resources, water chemistry), and (5) lava flows - lava tubes (more caves). Map unit groupings (e.g., belts, terranes, tectonic & geomorphic provinces) can also be derived from the geodatabase. Digital geologic mapping was used in ground water modeling to predict effects of tunneling through the San Bernardino Mountains. Bedrock mapping is used in models that characterize watershed sediment regimes and quantify anthropogenic influences. When combined with digital geomorphology mapping, this geodatabase helps to assess landslide hazards.

Identification of erosional and inundation hazard zones in Ken-Betwa river linking area, India, using remote sensing and GIS.

PubMed

Avtar, Ram; Singh, Chander Kumar; Shashtri, Satayanarayan; Mukherjee, Saumitra

2011-11-01

Ken-Betwa river link is one of the pilot projects of the Inter Linking of Rivers program of Government of India in Bundelkhand Region. It will connect the Ken and Betwa rivers through a system of dams, reservoirs, and canals to provide storage for excess rainfall during the monsoon season and avoid floods. The main objective of this study is to identify erosional and inundation prone zones of Ken-Betwa river linking site in India using remote sensing and geographic information system tools. In this study, Landsat Thematic Mapper data of year 2005, digital elevation model from the Shuttle Radar Topographic Mission, and other ancillary data were analyzed to create various thematic maps viz. geomorphology, land use/land cover, NDVI, geology, soil, drainage density, elevation, slope, and rainfall. The integrated thematic maps were used for hazard zonation. This is based on categorizing the different hydrological and geomorphological processes influencing the inundation and erosion intensity. Result shows that the southern part of the study area which lies in Panna district of Madhya Pradesh, India, is more vulnerable than the other areas.

Psychometric and Edumetric Validity of Dimensions of Geomorphological Knowledge Which Are Tapped by Concept Mapping.

ERIC Educational Resources Information Center

Hoz, Ron; Bowman, Dan; Chacham, Tova

1997-01-01

Students (N=14) in a geomorphology course took an objective geomorphology test, the tree construction task, and the Standardized Concept Structuring Analysis Technique (SConSAT) version of concept mapping. Results suggest that the SConSAT knowledge structure dimensions have moderate to good construct validity. Contains 82 references. (DDR)

Physiographic map of the Sicilian region (1:250,000 scale)

NASA Astrophysics Data System (ADS)

Priori, Simone; Fantappiè, Maria; Costantini, Edoardo A. C.

2015-04-01

Physiographic maps summarize and group the landforms of a territory into homogeneous areas in terms of kind and intensity of main geomorphological process. Most of the physiographic maps have large scale, which is national or continental scale. Other maps have been produced at the semi-detailed scales, while examples at the regional scale are much less common. However, being the Region the main administrative level in Europe, they can be very useful for land planning in many fields, such as ecological studies, risk maps, and soil mapping. This work presents a methodological example of regional physiographic map, compiled at 1:250,000 scale, representing the whole Sicilian region, the largest and most characteristic of Mediterranean island. The physiographic units were classed matching thematich layers (NDVI, geology, DEM, land cover) with the main geomorphological processes that were identified by stereo-interpretation of aerial photographs (1:70,000 scale). In addition, information from other published maps, representing geomorphological forms, aeolian deposits, anthropic terraced slopes, and landslide were used to improve the accuracy and reliability of the map. The classification of the physiographic units, and then the map legend, was built up on the basis of literature and taking into account Italian geomorphological legend. The legend proposed in this map, which can be applied also in other Mediterranean countries, is suitable for different scales. The landform units were grouped on the base of a geomorphological classification of the forms into: anthropogenic, eolian, coastal, valley floor, intermountain fluvial, slope erosional, structural, karstic, and volcanic.

The use of historical maps for reconstructing landforms before river damming. The case of the Swiss Rhone River

NASA Astrophysics Data System (ADS)

Reynard, E.; Laigre, L.; Baud, D.

2012-04-01

The Swiss Rhone River was systematically embanked during the period 1864-1893. The Swiss Rhone River valley is a glacial valley filled by glaciolacustrine, fluvioglacial and fluvial sediments. Torrential tributaries contribute to a large extent to the sedimentation in the valley and have built large alluvial fans in the main valley. The period before the river damming corresponds to the Little Ice Age, and it is supposed that the torrential behaviour of the river and its tributaries was very active during that period. In parallel to a large hydraulic project (Third Rhone River Correction), aiming at enlarging the river for security and environmental reasons, this project aims at reconstructing the palaeogeomorphology of the river floodplain before and also during the 30-year long embankment project developed during the last decades of the 19th century. The objective is to better know the geomorphological behaviour of the river, and also to localize palaolandforms (meanders, braided patterns, sandstone dunes, wetlands, etc.), present in the floodplain in the first part of the 19th century and that have now totally disappeared. The project is carried out in close collaboration with the Cantonal Archives of Valais and with a group of historians working on the relations between the river and the communities. It should contribute to a better knowledge of the Swiss Rhone River history (Reynard et al., 2009). Both published official maps (Dufour maps, Siegfried maps) and unpublished maps and plans are systematically collected, digitized, and organised in a database managed by a Geographical Information System. Other data are collected (place names, geomorphological, hydrological and hydraulic data, information about land-use and vegetation, paintings and photographs, etc.) and localised. A high-resolution digital terrain model and areal photographs are also used and allow us to map palaeolandforms (meanders, filled oxbow lakes, former channels, etc.). In a second step maps of the palaeogeomorphology of the river floodplain are produced and analysed in collaboration with the historian colleagues. Reference Reynard E., Evéquoz-Dayen M., Dubuis P. (eds) (2009). Le Rhône : dynamique, histoire et société. Sion, Cahiers de Vallesia 21, 238 p.

Topsoil moisture mapping using geostatistical techniques under different Mediterranean climatic conditions.

PubMed

Martínez-Murillo, J F; Hueso-González, P; Ruiz-Sinoga, J D

2017-10-01

Soil mapping has been considered as an important factor in the widening of Soil Science and giving response to many different environmental questions. Geostatistical techniques, through kriging and co-kriging techniques, have made possible to improve the understanding of eco-geomorphologic variables, e.g., soil moisture. This study is focused on mapping of topsoil moisture using geostatistical techniques under different Mediterranean climatic conditions (humid, dry and semiarid) in three small watersheds and considering topography and soil properties as key factors. A Digital Elevation Model (DEM) with a resolution of 1×1m was derived from a topographical survey as well as soils were sampled to analyzed soil properties controlling topsoil moisture, which was measured during 4-years. Afterwards, some topography attributes were derived from the DEM, the soil properties analyzed in laboratory, and the topsoil moisture was modeled for the entire watersheds applying three geostatistical techniques: i) ordinary kriging; ii) co-kriging considering as co-variate topography attributes; and iii) co-kriging ta considering as co-variates topography attributes and gravel content. The results indicated topsoil moisture was more accurately mapped in the dry and semiarid watersheds when co-kriging procedure was performed. The study is a contribution to improve the efficiency and accuracy of studies about the Mediterranean eco-geomorphologic system and soil hydrology in field conditions. Copyright © 2017 Elsevier B.V. All rights reserved.

Applying NASA Imaging Radar Datasets to Investigate the Geomorphology of the Amazon's Planalto

NASA Astrophysics Data System (ADS)

McDonald, K. C.; Campbell, K.; Islam, R.; Alexander, P. M.; Cracraft, J.

2016-12-01

The Amazon basin is a biodiversity rich biome and plays a significant role into shaping Earth's climate, ocean and atmospheric gases. Understanding the history of the formation of this basin is essential to our understanding of the region's biodiversity and its response to climate change. During March 2013, the NASA/JPL L-band polarimetric airborne imaging radar, UAVSAR, conducted airborne studies over regions of South America including portions of the western Amazon basin. We utilize UAVSAR imagery acquired during that time over the Planalto, in the Madre de Dios region of southeastern Peru in an assessment of the underlying geomorphology, its relationship to the current distribution of vegetation, and its relationship to geologic processes through deep time. We employ UAVSAR data collections to assess the utility of these high quality imaging radar data for use in identifying geomorphologic features and vegetation communities within the context of improving the understanding of evolutionary processes, and their utility in aiding interpretation of datasets from Earth-orbiting satellites to support a basin-wide characterization across the Amazon. We derive maps of landcover and river branching structure from UAVSAR imagery. We compare these maps to those derived using imaging radar datasets from the Japanese Space Agency's ALOS PALSAR and Digital Elevation Models (DEMs) from NASA's Shuttle Radar Topography Mission (SRTM). Results provide an understanding of the underlying geomorphology of the Amazon planalto as well as its relationship to geologic processes and will support interpretation of the evolutionary history of the Amazon Basin. Portions of this work have been carried out within the framework of the ALOS Kyoto & Carbon Initiative. PALSAR data were provided by JAXA/EORC and the Alaska Satellite Facility.This work is carried out with support from the NASA Biodiversity Program and the NSF DIMENSIONS of Biodiversity Program.

Glaciated valleys in Europe and western Asia

PubMed Central

Prasicek, Günther; Otto, Jan-Christoph; Montgomery, David R.; Schrott, Lothar

2015-01-01

In recent years, remote sensing, morphometric analysis, and other computational concepts and tools have invigorated the field of geomorphological mapping. Automated interpretation of digital terrain data based on impartial rules holds substantial promise for large dataset processing and objective landscape classification. However, the geomorphological realm presents tremendous complexity and challenges in the translation of qualitative descriptions into geomorphometric semantics. Here, the simple, conventional distinction of V-shaped fluvial and U-shaped glacial valleys was analyzed quantitatively using multi-scale curvature and a novel morphometric variable termed Difference of Minimum Curvature (DMC). We used this automated terrain analysis approach to produce a raster map at a scale of 1:6,000,000 showing the distribution of glaciated valleys across Europe and western Asia. The data set has a cell size of 3 arc seconds and consists of more than 40 billion grid cells. Glaciated U-shaped valleys commonly associated with erosion by warm-based glaciers are abundant in the alpine regions of mid Europe and western Asia but also occur at the margins of mountain ice sheets in Scandinavia. The high-level correspondence with field mapping and the fully transferable semantics validate this approach for automated analysis of yet unexplored terrain around the globe and qualify for potential applications on other planetary bodies like Mars. PMID:27019665

Mapping three-dimensional geological features from remotely-sensed images and digital elevation models

NASA Astrophysics Data System (ADS)

Morris, Kevin Peter

Accurate mapping of geological structures is important in numerous applications, ranging from mineral exploration through to hydrogeological modelling. Remotely sensed data can provide synoptic views of study areas enabling mapping of geological units within the area. Structural information may be derived from such data using standard manual photo-geologic interpretation techniques, although these are often inaccurate and incomplete. The aim of this thesis is, therefore, to compile a suite of automated and interactive computer-based analysis routines, designed to help a the user map geological structure. These are examined and integrated in the context of an expert system. The data used in this study include Digital Elevation Model (DEM) and Airborne Thematic Mapper images, both with a spatial resolution of 5m, for a 5 x 5 km area surrounding Llyn Cow lyd, Snowdonia, North Wales. The geology of this area comprises folded and faulted Ordo vician sediments intruded throughout by dolerite sills, providing a stringent test for the automated and semi-automated procedures. The DEM is used to highlight geomorphological features which may represent surface expressions of the sub-surface geology. The DEM is created from digitized contours, for which kriging is found to provide the best interpolation routine, based on a number of quantitative measures. Lambertian shading and the creation of slope and change of slope datasets are shown to provide the most successful enhancement of DEMs, in terms of highlighting a range of key geomorphological features. The digital image data are used to identify rock outcrops as well as lithologically controlled features in the land cover. To this end, a series of standard spectral enhancements of the images is examined. In this respect, the least correlated 3 band composite and a principal component composite are shown to give the best visual discrimination of geological and vegetation cover types. Automatic edge detection (followed by line thinning and extraction) and manual interpretation techniques are used to identify a set of 'geological primitives' (linear or arc features representing lithological boundaries) within these data. Inclusion of the DEM data provides the three-dimensional co-ordinates of these primitives enabling a least-squares fit to be employed to calculate dip and strike values, based, initially, on the assumption of a simple, linearly dipping structural model. A very large number of scene 'primitives' is identified using these procedures, only some of which have geological significance. Knowledge-based rules are therefore used to identify the relevant. For example, rules are developed to identify lake edges, forest boundaries, forest tracks, rock-vegetation boundaries, and areas of geomorphological interest. Confidence in the geological significance of some of the geological primitives is increased where they are found independently in both the DEM and remotely sensed data. The dip and strike values derived in this way are compared to information taken from the published geological map for this area, as well as measurements taken in the field. Many results are shown to correspond closely to those taken from the map and in the field, with an error of < 1°. These data and rules are incorporated into an expert system which, initially, produces a simple model of the geological structure. The system also provides a graphical user interface for manual control and interpretation, where necessary. Although the system currently only allows a relatively simple structural model (linearly dipping with faulting), in the future it will be possible to extend the system to model more complex features, such as anticlines, synclines, thrusts, nappes, and igneous intrusions.

Geotourist itineraries along the Italian territory: examples of mapping the geoheritage in different geomorphological and historical contexts

NASA Astrophysics Data System (ADS)

Panizza, Valeria; Brandolini, Pierluigi; Laureti, Lamberto; Nesci, Olivia; Russo, Filippo; Savelli, Daniele

2016-04-01

In the framework of the studies dealing with geomorphosites mapping, many researches were carried out in the last years presenting both applied examples and proposals for tourist fruition. Researchers had to face many different challenges in transferring the knowledge about the geomorphological heritage on maps. The most relevant are those concerning the use of maps for tourist promotion, taking into account the requirements of clearness of representation of landforms and also the need of pointing out possible geomorphological hazards along tourist paths. Within the activity of the Working Group "Geomorphosites and Cultural Landscape" of AIGeo (Italian Association of Physical Geography and Geomorphology), some Italian itineraries, focused on the promotion of the geomorphological heritage by means of geotourist maps, are presented. They have the goal of: promoting landscape through its geomorphological and geological heritage; disseminating geoheritage knowledge focusing its relationships with cultural landscape and human history; assessing geomorphological hazards and possible risk situations The proposed itineraries are localised in different Italian regions and they concern: - the area around the remains of the Roman town of Ostra. The town is placed on the left side of the Misa River (Marche region, Italy), atop a stream terrace dating back to the uppermost Pleistocene-early Holocene. Detailed geomorphological field and remote-sensing mapping started in 2015. The surveying is aimed at focusing the geomorphological evolution as well as at assessing possible geomorphological hazard for both conservation and exploitation scopes. A geotourist trail is proposed with the aim of highlighting and integrating geomorphological and archaeological elements and information. - a geotourist trail along the coastal terraced slopes of Cinque Terre (Liguria, NW Italy): worldwide considered as one of the most outstanding examples of human integration with the natural landscape within the Mediterranean region. The Cinque Terre are has been recognized since 1997 as a World Heritage Site by UNESCO and are currently affected by high geomorphological risk. - the territory of the town of Bosa, north-western Sardinia (Italy). From a geological point of view the area is characterized by the outcropping of the Oligo-Miocene volcanic sequence related to the rotational tectonic. The geomorphological survey allowed the reconstruction of the Quaternary evolution and the assessment of the geomorphological heritage. The itinerary proposed wants to promote, by means of a geo-tourist map, the geomorphological heritage in its relationship with the rich cultural context and give all information for a correct and conscious fruition of the landscape. - the vacant railway tract Avellino-Rocchetta S. Antonio (Campania region, Italy): an inland area of the southern Italian Apennine. Here the great diversity of landforms give rise to a rich variety of landscapes, strictly linked with the long archaeological and cultural history, protected, in part, by the institution of regional Parks and other kind of protected areas. - abandoned or deactivated old mines in the Eastern Italian Alps, in order to promote their recovery for tourist or didactic purposes. The aim of the proposed itinerary is to organize its specific fruition as well as the preservation of their environmental and historic heritage.

Detailed geomorphological mapping of debris-covered and rock glaciers in the Hólar area, Tröllaskagi Peninsula (northern Iceland).

NASA Astrophysics Data System (ADS)

Tanarro, Luis M.; Palacios, David; Zamorano, Jose J.; Andres, Nuria

2017-04-01

Most studies conducted on rock and debris-covered glaciers only include simplified geomorphological maps representing main units (ridges, furrows, front, and thermokarst depressions). The aim of this study is to develop a detailed geomorphological mapping of the Hóladalsjökull debris-covered glacier (65°42' N; 18°57' W) and the Fremri-Grjótárdalur rock glacier (65°43' N 19° W), located near Hólar, a village in the central area of the Trolläskagi peninsula (northern Iceland). The mapping process has been conducted using standard stereo-photointerpretation of aerial photographs and stereo-plotting of a topographic map at 1:2000 scale. Also, landforms have been represented in different transects. Lastly, the geomorphological map has been designed using the elevation digital model, and a 3D pdf file has been generated, allowing for better viewing and understanding the different units and their modelling. The geomorphological mapping of the Hóladalsjökull debris-covered glacier and the Fremri-Grjótárdalur rock glacier represents the prominent walls of their valley heads and their summits, which form a flat highland at 1,200-1,330 metres above sea level, covered by blockfield and patterned ground features. Rockfall and slide landforms are common processes at the foot of these 100-170 metre-high cirque-walls. Debris-covered glaciers and rock glaciers are born right under these walls, building up a spoon-shaped hollow around glacial ice, surrounded by young moraine ridges at their fronts. The dominant features in the Hóladalsjökull debris-covered glacier are large longitudinal ridges and furrows, stretching over 1.5 km in length in the central and western areas. Medium-sized thermokarst depressions (between 15-40 metres in diameter), often running parallel to the furrows, dot the surface of the debris-covered glacier. Parallel alternate ridges and furrows can be seen near the snout. Ridges are rugged and fall around 30-40 metres, with over 30 degree slopes, whereas furrows have smoother hillsides. The snout of the debris-covered glacier is around 900 m high. Several units of rock glaciers from different overlapping ages can be distinguished in the Fremri-Grjótárdalur cirque. Deep and meandering furrows have developed in the contact areas between the main lobes. The lobes of the youngest rock glaciers, located at the cirque head, reach a length of between 0.5 km and 1 km. Their morphology changes from their rooting zone, with alternate smooth furrows and ridges extending towards their front, where steep ridges and furrows appear, and ends in a steep front between 896 and 922 m high. These rock glaciers overlap one another on a fossil rock glacier, rising another 400 m until they reach a height of 850 m. Research funded by Deglaciation project (CGL2015-65813-R), Government of Spain

Geologic map of Big Bend National Park, Texas

USGS Publications Warehouse

Turner, Kenzie J.; Berry, Margaret E.; Page, William R.; Lehman, Thomas M.; Bohannon, Robert G.; Scott, Robert B.; Miggins, Daniel P.; Budahn, James R.; Cooper, Roger W.; Drenth, Benjamin J.; Anderson, Eric D.; Williams, Van S.

2011-01-01

The purpose of this map is to provide the National Park Service and the public with an updated digital geologic map of Big Bend National Park (BBNP). The geologic map report of Maxwell and others (1967) provides a fully comprehensive account of the important volcanic, structural, geomorphological, and paleontological features that define BBNP. However, the map is on a geographically distorted planimetric base and lacks topography, which has caused difficulty in conducting GIS-based data analyses and georeferencing the many geologic features investigated and depicted on the map. In addition, the map is outdated, excluding significant data from numerous studies that have been carried out since its publication more than 40 years ago. This report includes a modern digital geologic map that can be utilized with standard GIS applications to aid BBNP researchers in geologic data analysis, natural resource and ecosystem management, monitoring, assessment, inventory activities, and educational and recreational uses. The digital map incorporates new data, many revisions, and greater detail than the original map. Although some geologic issues remain unresolved for BBNP, the updated map serves as a foundation for addressing those issues. Funding for the Big Bend National Park geologic map was provided by the United States Geological Survey (USGS) National Cooperative Geologic Mapping Program and the National Park Service. The Big Bend mapping project was administered by staff in the USGS Geology and Environmental Change Science Center, Denver, Colo. Members of the USGS Mineral and Environmental Resources Science Center completed investigations in parallel with the geologic mapping project. Results of these investigations addressed some significant current issues in BBNP and the U.S.-Mexico border region, including contaminants and human health, ecosystems, and water resources. Funding for the high-resolution aeromagnetic survey in BBNP, and associated data analyses and interpretation, was from the USGS Crustal Geophysics and Geochemistry Science Center. Mapping contributed from university professors and students was mostly funded by independent sources, including academic institutions, private industry, and other agencies.

Characterisation and quantification of groundwater-surface water interactions along an alluvial stream using geophysical, hydraulic and tracer methods

NASA Astrophysics Data System (ADS)

Rumph Frederiksen, R.; Rasmussen, K. R.; Christensen, S.

2015-12-01

Qualifying and quantifying water, nutrient and contaminant exchange at the groundwater-surface water interface are becoming increasingly important for water resources management. The objectives of this study are to characterise an alluvial stream using geophysics in addition to traditional geological and geomorphological data and quantify the groundwater seepage to the stream on point-to-reach scale using both hydraulic and tracer methods. We mapped the very shallow subsurface along an alluvial stream using a GCM system (DUALEM421S, an electromagnetic system that can be operated behind a boat or towed behind a motorized vehicle) as well as using geological logs from a large number of old wells. Furthermore we made geomorphological observations through digital maps (old topographical maps and aerial photos) and field observations. We measured stream discharge (quasi-) simultaneously at several positions along the stream using both an Ott-C31 propeller instrument and an Acoustic Doppler Current Profiler instrument. The measurements were made during dry summer periods when baseflow is expected to be the dominating contribution to streamflow. Preliminary findings show that the GCM system reveals small-scale structures not seen with other data types. Furthermore, based on the GCM results and stream discharge results we have identified gaining, losing and zero exchange sections of the stream. During late summer 2015 we will collect additional hydrological data in order to support or modify our preliminary findings. To further investigate the spatial and temporal variations of the groundwater-surface water interactions along the stream we will measure groundwater seepage to the stream using: seepage meter (point-scale) DTS (reach-scale) temperature stick measurements (point-in-space-and-time-scale) temperature loggers installed in the streambed (month-scale) The measurement sites are chosen based on our geophysical, geological, and geomorphological mapping as well as our stream discharge measurements.

Digital field mapping for stimulating Secondary School students in the recognition of geological features and landforms

NASA Astrophysics Data System (ADS)

Giardino, Marco; Magagna, Alessandra; Ferrero, Elena; Perrone, Gianluigi

2015-04-01

Digital field mapping has certainly provided geoscientists with the opportunity to map and gather data in the field directly using digital tools and software rather than using paper maps, notebooks and analogue devices and then subsequently transferring the data to a digital format for subsequent analysis. But, the same opportunity has to be recognized for Geoscience education, as well as for stimulating and helping students in the recognition of landforms and interpretation of the geological and geomorphological components of a landscape. More, an early exposure to mapping during school and prior to university can optimise the ability to "read" and identify uncertainty in 3d models. During 2014, about 200 Secondary School students (aged 12-15) of the Piedmont region (NW Italy) participated in a research program involving the use of mobile devices (smartphone and tablet) in the field. Students, divided in groups, used the application Trimble Outdoors Navigators for tracking a geological trail in the Sangone Valley and for taking georeferenced pictures and notes. Back to school, students downloaded the digital data in a .kml file for the visualization on Google Earth. This allowed them: to compare the hand tracked trail on a paper map with the digital trail, and to discuss about the functioning and the precision of the tools; to overlap a digital/semitransparent version of the 2D paper map (a Regional Technical Map) used during the field trip on the 2.5D landscape of Google Earth, as to help them in the interpretation of conventional symbols such as contour lines; to perceive the landforms seen during the field trip as a part of a more complex Pleistocene glacial landscape; to understand the classical and innovative contributions from different geoscientific disciplines to the generation of a 3D structural geological model of the Rivoli-Avigliana Morainic Amphitheatre. In 2013 and 2014, some other pilot projects have been carried out in different areas of the Piedmont region, and in the Sesia Val Grande Geopark, for testing the utility of digital field mapping in Geoscience education. Feedback from students are positive: they are stimulated and involved by the use of ICT for learning Geoscience, and they voluntary choose to work with their personal mobile device (more than 90% of them own a smartphone); they are interested in knowing the features of GPS, and of software for the visualization of satellite and aerial images, but they recognize the importance of integrating and comparing traditional and innovative methods in the field.

Geomorphometric analysis of cave ceiling channels mapped with 3-D terrestrial laser scanning

NASA Astrophysics Data System (ADS)

Gallay, Michal; Hochmuth, Zdenko; Kaňuk, Ján; Hofierka, Jaroslav

2016-05-01

The change of hydrological conditions during the evolution of caves in carbonate rocks often results in a complex subterranean geomorphology, which comprises specific landforms such as ceiling channels, anastomosing half tubes, or speleothems organized vertically in different levels. Studying such complex environments traditionally requires tedious mapping; however, this is being replaced with terrestrial laser scanning technology. Laser scanning overcomes the problem of reaching high ceilings, providing new options to map underground landscapes with unprecedented level of detail and accuracy. The acquired point cloud can be handled conveniently with dedicated software, but applying traditional geomorphometry to analyse the cave surface is limited. This is because geomorphometry has been focused on parameterization and analysis of surficial terrain. The theoretical and methodological concept has been based on two-dimensional (2-D) scalar fields, which are sufficient for most cases of the surficial terrain. The terrain surface is modelled with a bivariate function of altitude (elevation) and represented by a raster digital elevation model. However, the cave is a 3-D entity; therefore, a different approach is required for geomorphometric analysis. In this paper, we demonstrate the benefits of high-resolution cave mapping and 3-D modelling to better understand the palaeohydrography of the Domica cave in Slovakia. This methodological approach adopted traditional geomorphometric methods in a unique manner and also new methods used in 3-D computer graphics, which can be applied to study other 3-D geomorphological forms.

Can we follow the neotectonic activity of the Hluboká-fault by reconstructing the evolution of the Vltava river course? - Mapping of fluvial terraces around the Budejovice-basin using historic maps

NASA Astrophysics Data System (ADS)

Homolova, Dana; Lomax, Johanna; Prachar, Ivan; Spacek, Petr; Zamolyi, Andras; Decker, Kurt

2010-05-01

The Budějovice Basin in the Bohemian Massif (Czech Republic) is a fault-bounded sedimentary basin with a multiple subsidence history overlying Variscan crystalline basement. Permian, Cretaceous and Miocene sediments record repeated reactivations of faults at or close to the basin margin, which may have continued into the Quaternary. The latter is indicated by geomorphological features such as linear topographic scarps, which characterize part of the faults within and at the border of the Budějovice Basin. In a current study we assess possible Quaternary displacements along the faults delimiting the basin using geomorphological data, analyses of river planform patterns and correlations of Quaternary terraces of the Vltava River, which crosses the basin and its boundary faults. The regionally most important tectonic feature - the Hluboká fault -forms the northeastern margin of the Budějovice basin. The fault crosses the course of the river Vltava, a fact that guided our research to take a more precise look at the character and distribution of fluvial sediments in this area. Our main focus is on dating of terrace bodies around the Hluboká fault. According to the scheme used in most European regions, influences by the Pleistocene glacial cycles, the Vltava river terraces were assigned by most scientists to the 4(5) main alpine glacial periods. This dating is not straightforward as terraces are not connected to moraine bodies like in the Alps. The terraces were basically correlated by their altitude above the river and by their lithology (clastic content and grain size composition), but mostly without any numerical age determination. Our studies include several field and laboratory methods, supported by computer analyses of various types of spatial data. Data sources include: (i) modern topographic maps, (ii) geological maps, (iii) georeferenced historic map sheets of the Austrian Second Military Survey (provided by the Geoinformatics Laboratory of the University J. E. Purkyně, 2005). The georeferenced map sheets of the Second Military Survey provide a very exact base map (Timár et al., 2006) for investigating the location of possible terrace bases. Since the georeferencing accuracy is < 10 m, data from these map sheets can be integrated into the geomorphologic studies providing information about the geomorphologic situation in the study area of the years 1836-1842, i.e., with less anthropogenic impact on geomorphological features than today. These data sources are combined with data from boreholes and thus help us identifying potential terrace bodies and choosing appropriate investigation sites. In the field, morphological, sedimentological and pedological methods are used to obtain relevant data about the sediment stratigraphy. Several laboratory analyses were carried out to gain information on the age of the terraces. We use OSL-dating in combination with the analysis of heavy minerals and clay minerals, as well as grain size analysis. After gathering information about the absolute ages of the terrace bodies upstream and downstream the Hluboká fault, we may be able to declare if the building of terrace staircases was influenced by tectonic activity of the fault or not. Timár, G., Molnár, G., Székely, B., Biszak, S., Varga, J., Jankó, A. (2006): Digitized maps of the Habsburg Empire - The map sheets of the second military survey and their georeferenced version. Arcanum, Budapest, 59 p. ISBN 963-7374-33-7

Tampa Bay Study Data and Information Management System (DIMS)

NASA Astrophysics Data System (ADS)

Edgar, N. T.; Johnston, J. B.; Yates, K.; Smith, K. E.

2005-05-01

Providing easy access to data and information is an essential component of both science and management. The Tampa Bay Data and Information Management System (DIMS) catalogs and publicizes data and products which are generated through the Tampa Bay Integrated Science Study. The publicly accessible interface consists of a Web site (http://gulfsci.usgs.gov), a digital library, and an interactive map server (IMS). The Tampa Bay Study Web site contains information from scientists involved in the study, and is also the portal site for the digital library and IMS. Study information is highlighted on the Web site according to the estuarine component: geology and geomorphology, water and sediment quality, ecosystem structure and function, and hydrodynamics. The Tampa Bay Digital Library is a web-based clearinghouse for digital products on Tampa Bay, including documents, maps, spatial and tabular data sets, presentations, etc. New developments to the digital library include new search features, 150 new products over the past year, and partnerships to expand the offering of science products. The IMS is a Web-based geographic information system (GIS) used to store, analyze and display data pertaining to Tampa Bay. Upgrades to the IMS have improved performance and speed, as well as increased the number of data sets available for mapping. The Tampa Bay DIMS is a dynamic entity and will continue to evolve with the study. Beginning in 2005, the Tampa Bay Integrated Coastal Model will have a more prominent presence within the DIMS. The Web site will feature model projects and plans; the digital library will host model products and data sets; the IMS will display spatial model data sets and analyses. These tools will be used to increase communication of USGS efforts in Tampa Bay to the public, local managers, and scientists.

Landslide inventory maps: New tools for an old problem

NASA Astrophysics Data System (ADS)

Guzzetti, Fausto; Mondini, Alessandro Cesare; Cardinali, Mauro; Fiorucci, Federica; Santangelo, Michele; Chang, Kang-Tsung

2012-04-01

Landslides are present in all continents, and play an important role in the evolution of landscapes. They also represent a serious hazard in many areas of the world. Despite their importance, we estimate that landslide maps cover less than 1% of the slopes in the landmasses, and systematic information on the type, abundance, and distribution of landslides is lacking. Preparing landslide maps is important to document the extent of landslide phenomena in a region, to investigate the distribution, types, pattern, recurrence and statistics of slope failures, to determine landslide susceptibility, hazard, vulnerability and risk, and to study the evolution of landscapes dominated by mass-wasting processes. Conventional methods for the production of landslide maps rely chiefly on the visual interpretation of stereoscopic aerial photography, aided by field surveys. These methods are time consuming and resource intensive. New and emerging techniques based on satellite, airborne, and terrestrial remote sensing technologies, promise to facilitate the production of landslide maps, reducing the time and resources required for their compilation and systematic update. In this work, we first outline the principles for landslide mapping, and we review the conventional methods for the preparation of landslide maps, including geomorphological, event, seasonal, and multi-temporal inventories. Next, we examine recent and new technologies for landslide mapping, considering (i) the exploitation of very-high resolution digital elevation models to analyze surface morphology, (ii) the visual interpretation and semi-automatic analysis of different types of satellite images, including panchromatic, multispectral, and synthetic aperture radar images, and (iii) tools that facilitate landslide field mapping. Next, we discuss the advantages and the limitations of the new remote sensing data and technology for the production of geomorphological, event, seasonal, and multi-temporal inventory maps. We conclude by arguing that the new tools will help to improve the quality of landslide maps, with positive effects on all derivative products and analyses, including erosion studies and landscape modeling, susceptibility and hazard assessments, and risk evaluations.

Geomorphological mapping with a small unmanned aircraft system (sUAS): Feature detection and accuracy assessment of a photogrammetrically-derived digital terrain model

NASA Astrophysics Data System (ADS)

Hugenholtz, Chris H.; Whitehead, Ken; Brown, Owen W.; Barchyn, Thomas E.; Moorman, Brian J.; LeClair, Adam; Riddell, Kevin; Hamilton, Tayler

2013-07-01

Small unmanned aircraft systems (sUAS) are a relatively new type of aerial platform for acquiring high-resolution remote sensing measurements of Earth surface processes and landforms. However, despite growing application there has been little quantitative assessment of sUAS performance. Here we present results from a field experiment designed to evaluate the accuracy of a photogrammetrically-derived digital terrain model (DTM) developed from imagery acquired with a low-cost digital camera onboard an sUAS. We also show the utility of the high-resolution (0.1 m) sUAS imagery for resolving small-scale biogeomorphic features. The experiment was conducted in an area with active and stabilized aeolian landforms in the southern Canadian Prairies. Images were acquired with a Hawkeye RQ-84Z Areohawk fixed-wing sUAS. A total of 280 images were acquired along 14 flight lines, covering an area of 1.95 km2. The survey was completed in 4.5 h, including GPS surveying, sUAS setup and flight time. Standard image processing and photogrammetric techniques were used to produce a 1 m resolution DTM and a 0.1 m resolution orthorectified image mosaic. The latter revealed previously un-mapped bioturbation features. The vertical accuracy of the DTM was evaluated with 99 Real-Time Kinematic GPS points, while 20 of these points were used to quantify horizontal accuracy. The horizontal root mean squared error (RMSE) of the orthoimage was 0.18 m, while the vertical RMSE of the DTM was 0.29 m, which is equivalent to the RMSE of a bare earth LiDAR DTM for the same site. The combined error from both datasets was used to define a threshold of the minimum elevation difference that could be reliably attributed to erosion or deposition in the seven years separating the sUAS and LiDAR datasets. Overall, our results suggest that sUAS-acquired imagery may provide a low-cost, rapid, and flexible alternative to airborne LiDAR for geomorphological mapping.

Geomorphological map as a tool for visualisation of geodiversity - example from Cave Park Grabovaca (Croatia)

NASA Astrophysics Data System (ADS)

Buzjak, Nenad; Bocic, Neven; Pahernik, Mladen

2014-05-01

Cave Park Grabovaca is located near Perusic in Lika region (central Croatia). It was established in 2006 at the area of 5.95 km2 (protection category: significant landscape). The main task is management and protection of Samograd, Medina and Amidzina caves that were declared as geomorphological monuments, and 6 other caves located close to each other. Owing to the central geographic location in Croatian Dinaric karst area, good traffic connections between central Europe and tourist centres of the Adriatic coast, preserved nature and easy accessible karst features typical for the Dinaric Karst, it has good potential to develop as an research, educational and tourist centre. In 2013. Cave Park management and the Department of Geography (University of Zagreb, Faculty of Science) established a core team that started to develop the project of Geoeducational centre (GEC) with following goals: exploration-evaluation-presentation-education. According to the accepted strategy, the first step in the project process is to enlarge the area and change the protection category. During the consultation process team members take into account protection, environmental, local economy, tourism and local population issues and proposed that protected area should be increased to 52,2 km2. This enlargement provides more efficient protection, greater geodiversity and biodiversity by occupying geotope, biotope, and landscape units typical for the whole Lika karst region. The next step was inventorying, evaluation, analysis and visualisation of geological, geomorphological and speleological phenomena. This 2 year task was made in cooperation between Croatian Geomorphological Society, Department of Geography, Speleological Society Karlovac and Caving Club Samobor. The inventory was made using field-work mapping and geotagged photographs, cave mapping and DEM analysis. It resulted in GIS oriented geodatabase consisting of geomorphological forms, processes and cave inventory. From those data geomorphological map 1:25.000, morphometrical maps (hypsometrical, slope, relative relief) and speleological maps were produced. Cartographic model of the geomorphological map is defined by 5 groups: geological structure, morphogenetic, morphographic, morphometric and morpho-chronological data. The geodatabase and maps were used for preparing the study as a part of regulated legal procedure for protected area enlargement. It is also a plan to use it for karst and landscape geodiversity presentation and education. For that purpose general geomorphological map, with professional symbology understandable only to professionals, must be didactically transformed to media that is visually and contextually acceptable to wider non-professional audience.

Development of a new British Geologcial Survey(BGS) Map Series: Seabed Geomorphology

NASA Astrophysics Data System (ADS)

Dove, Dayton

2015-04-01

BGS scientists are developing a new offshore map series, Seabed Geomorphology (1:50k), to join the existing 1:250k 'Sea Bed Sediments', 'Quaternary Geology', and 'Solid Geology' map series. The increasing availability of extensive high-resolution swath bathymetry data (e.g. MCA's Civil Hydrography Programme) provides an unprecedented opportunity to characterize the processes which formed, and actively govern the physical seabed environment. Mapping seabed geomorphology is an effective means to describe individual, or groups of features whose form and other physical attributes (e.g. symmetry) may be used to distinguish feature origin. Swath bathymetry also provides added and renewed value to other data types (e.g. grab samples, legacy seismic data). In such cases the geomorphic evidence may be expanded to make inferences on the evolution of seabed features as well as their association with the underlying geology and other environmental variables/events over multiple timescales. Classifying seabed geomorphology is not particularly innovative or groundbreaking. Terrestrial geomorphology is of course a well established field of science, and within the marine environment for example, mapping submarine glacial landforms has probably become the most reliable method to reconstruct the extent and dynamics of past ice-sheets. What is novel here, and we believe useful/necessary for a survey organization, is to standardise the geomorphological classification scheme such that it is applicable to multiple and diverse environments. The classification scheme should be sufficiently detailed and interpretive to be informative, but not so detailed that we over-interpret or become mired in disputed feature designations or definitions. We plan to present the maps at 1:50k scale with the intention that these maps will be 'enabling' resources for research, educational, commercial, and policy purposes, much like the existing 1:250k map series. We welcome feedback on the structure and content of the proposed classification scheme, as well as the anticipated value to respective user communities.

Integrated geomorphologic and GIS analysis for the assessment of erosion zones and its relationship with hazardous zones in the Zacatecas and Guadalupe quadrangles, Mexico

NASA Astrophysics Data System (ADS)

Escalona-Alcázar, F. d. J.; Escobedo-Arellano, B.; Castillo-Félix, B.; Carrillo-Castillo, C.; García-Sandoval, P.; Gurrola-Menchaca, L. L.; Núñez-Peña, E. P.; Esparza-Martínez, A.; Bluhm-Gutiérrez, J.; Guijarro-Rodríguez, C. J.

2012-04-01

The morphology of the Zacatecas and Guadalupe quadrangles is composed to the West by a NNE-SSW fault bounded range and to the East a valley cut by minor hills. The most important and fast growing cities in the state are located in that range. However, in urban development plans variables such as the geology and geomorphologic processes, as well as the land cover characteristics, are poorly taken into consideration. Due to the landscape modification the erosion agents, mainly water, removes loose materials that are either natural or artificial. The effects on the buildings and roads are fractures, slope instability, and rock falling. In this study we present a model that considers the detailed geologic mapping, the geomorphology, land use, vegetation, and the digital slope model scale 1:50 000. The geomorphologic parameters considered were: relief energy, dissection density, general dissection density, and maximum dissection depth. The location and internal characteristics of mapped talus deposits were the basis to define the erosion criteria. High erosion zones are located in slopes over 20° where the talus deposits initiate due to the relative abundance of loose debris. Medium erosion areas are located in slopes over 10° that downslope has progressive accumulation of sediments. While the low erosion zones are located in slopes ranging from 5° to 20° with almost flat lying beds. These parameters were analyzed in ArcGIS together with the digital slope model, detailed geology mapping, the land use cover, and the soil information. The results where verified in the range where the city has been growing in recent years. The soils all over the range are lithosols which are only 10 to 15 cm thick; while the vegetation is composed mainly of bushes and nopals. Even though both, vegetation and soil are not modified, the erosion effects in them are very slow regardless of their location. The faults located in high erosion zones facilitate rock falling mainly during the rainy season; whereas in medium erosion zones it occurs if the road cuts or cliffs are steep. The rocks varying from loose to moderately consolidated, as well as the artificial fillings and talus deposits, are easily or difficultly eroded according with the erosion zones proposed in our model. The effects observed are fractured roads and house walls, removal of soil underneath the buildings, gullies formation, and slope instability. The model defines areas where the erosion effects can be related to the development of hazardous zones. This model gives criteria for land use planning and urban development.

Evaluation of TanDEM-X elevation data for geomorphological mapping and interpretation in high mountain environments - A case study from SE Tibet, China

NASA Astrophysics Data System (ADS)

Pipaud, Isabel; Loibl, David; Lehmkuhl, Frank

2015-10-01

Digital elevation models (DEMs) are a prerequisite for many different applications in the field of geomorphology. In this context, the two near-global medium resolution DEMs originating from the SRTM and ASTER missions are widely used. For detailed geomorphological studies, particularly in high mountain environments, these datasets are, however, known to have substantial disadvantages beyond their posting, i.e., data gaps and miscellaneous artifacts. The upcoming TanDEM-X DEM is a promising candidate to improve this situation by application of state-of-the-art radar technology, exhibiting a posting of 12 m and less proneness to errors. In this study, we present a DEM processed from a single TanDEM-X CoSSC scene, covering a study area in the extreme relief of the eastern Nyainqêntanglha Range, southeastern Tibet. The potential of the resulting experimental TanDEM-X DEM for geomorphological applications was evaluated by geomorphometric analyses and an assessment of landform cognoscibility and artifacts in comparison to the ASTER GDEM and the recently released SRTM 1″ DEM. Detailed geomorphological mapping was conducted for four selected core study areas in a manual approach, based exclusively on the TanDEM-X DEM and its basic derivates. The results show that the self-processed TanDEM-X DEM yields a detailed and widely consistent landscape representation. It thus fosters geomorphological analysis by visual and quantitative means, allowing delineation of landforms down to footprints of 30 m. Even in this premature state, the TanDEM-X elevation data are widely superior to the ASTER and SRTM datasets, primarily owing to its significantly higher resolution and its lower susceptibility to artifacts that hamper landform interpretation. Conversely, challenges toward interferometric DEM generation were identified, including (i) triangulation facets and missing topographic information resulting from radar layover on steep slopes facing toward the radar sensor, (ii) low coherence values on leeward slopes, (iii) decorrelation effects over water bodies, and (iv) challenges for phase unwrapping in settings of strong topographic contrasts. There is, however, a high probability that these drawbacks can be overcome by applying multiple interferograms exhibiting different perpendicular baselines as planned for the generation of the final TanDEM-X DEM product.

GIS-based realization of international standards for digital geological mapping - developments in planetary mapping

NASA Astrophysics Data System (ADS)

Nass, Andrea; van Gasselt, Stephan; Jaumann, Ralf

2010-05-01

The Helmholtz Alliance and the European Planetary Network are research communities with different main topics. One of the main research topics which are shared by these communities is the question about the geomorphological evolutions of planetary surfaces as well as the geological context of life. This research contains questions like "Is there volcanic activity on a planet?" or "Where are possible landing sites?". In order to help answering such questions, analyses of surface features and morphometric measurements need to be performed. This ultimately leads to the generation of thematic maps (e.g. geological and geomorphologic maps) as a basis for the further studies. By using modern GIS techniques the comparative work and generalisation during mapping processes results in new information. These insights are crucial for subsequent investigations. Therefore, the aim is to make these results available to the research community as a secondary data basis. In order to obtain a common and interoperable data collection results of different mapping projects have to follow a standardised data-infrastructure, metadata definition and map layout. Therefore, we are currently focussing on the generation of a database model arranging all data and processes in a uniform mapping schema. With the help of such a schema, the mapper will be able to utilise a predefined (but customisable) GIS environment with individual tool items as well as a standardised symbolisation and a metadata environment. This environment is based on a data model which is currently on a conceptual level and provides the layout of the data infrastructure including relations and topologies. One of the first tasks towards this data model is the definition of a consistent basis of symbolisation standards developed for planetary mapping. The mapper/geologist will be able to access the pre-built signatures and utilise these in scale dependence within the mapping project. The symbolisation will be related to the data model in the next step. As second task, we designed a concept for description of the digital mapping result. Therefore, we are creating a metadata template based on existing standards for individual needs in planetary sciences. This template is subdivided in (meta) data about the general map content (e.g. on which data the mapping result based on) and in metadata for each individual mapping element/layer comprising information like minimum mapping scale, interpretation hints, etc. The assignment of such a metadata description in combination with the usage of a predefined mapping schema facilitates the efficient and traceable storage of data information on a network server and enables a subsequent representation, e.g. as a mapserver data structure. Acknowledgement: This work is partly supported by DLR and the Helmholtz Alliance "Planetary Evolution and Life".

Space imagery and some geomorphological problems of the Guiana Shield, South America

NASA Technical Reports Server (NTRS)

Melhorn, W. N.

1985-01-01

Some ongoing involvement in regional geomorphologic research in South America is described. Because of association with LARS at Purdue University, there has been engagement, vicarious or adivsory, in projects which led to LANDSAT 1-2 mapping of the natural resources of Bolivia (1:8,000,000 scale), and preparation of a geographic information system which mapped the general hydrology, geology, soils, and vegetation of Ecuador (1:4,000,000 scale). Currently we are involved more specifically in geological-geomorphological mapping of the Venezuelan portion of the Guiana shield, and because of manuscript limitations only questions pertinent to this region are posed in the ensuing discussion.

Geodiversity characterization and assessment of the Morainic Amphitheatre of Rivoli -Avigliana (NW-Italy)

NASA Astrophysics Data System (ADS)

Giordano, Enrico; Lucchesi, Stefania; Perotti, Luigi; Giardino, Marco

2014-05-01

The concept of Geodiversity in its wide sense refers specifically to particular geosystems that are in themselves complex (e.g diverse) assemblages of bedrock, landform, and soil features. Therefore, geodiversity assessment is strictly related to landscape structure, whose studies are in the field of complex Physical Geography. Moreover, Geodiversity studies provide a fundamental base for geoconservation and environmental management in a holistic way. This is particularly true within complex geomorphological environments, where many intrinsic and extrinsic factors are interconnected. Various procedures has been already applied for the creation of geodiversity maps in different geomorphological context, but especially in wide areas with a large geodiversity of landforms. Pleistocene morainic amphitheatres of the Alpine piedmont regions are indeed particular and complex environments: not only for the geological and geomorphological points of view, but also for their relationships with biotic components and human life. The aim of this study is to carry out a geodiversity characterization of the Rivoli-Avigliana Morainic Amphitheatre (AMRA; NW Italy). The AMRA separates the lower Susa Valley from the middle course of the Sangone River; it is a set of low hills and depressions related to glacial pulsations aged between 750,000 and 12,000 years ago. Earth Sciences knowledge of the area has been compared to detailed field geomorphological and territorial data in order to determine qualitative and quantitative landscape parameters and to evaluate their validity for geodiversity assessment. A first qualitative characterization of the AMRA and an estimation of its geodiversity have been performed by means of geomorphological mapping and stratigraphic studies, including geomorphosites assessment for the same area. Then, geodiversity characterization and evaluation have been performed through the definition and application of quantitative parameters (landform energy, slope, land use, roughness, and other geomorphologic, hydrologic and geologic indexes). After acquisition of vector data, satellite and aerial images, GIS procedures allowed to manage and to process images and data: this allowed to interpret morphometric indexes and to obtain thematic maps with 3D views. Finally, results from the calculation of geodiversity and geomorphosites have been compared. Results turned out to be very effective for the study and for the reconstruction of the AMRA evolutionary stages, also for interpreting scenarios of future natural hazards, land occupation and risks posed to geodiversity for natural and anthropogenic causes. Geomatics devices and digital data demonstrated to be really suitable for improved analysis and representation of the observed phenomena. They can be easily integrated within GIS for decision support requirements. In this way, field and remote sensing data, together with indexes of biotic and abiotic aspects can generate synthetic information, to produce effective spatial interpolations and impressive 3D scenarios useful for Earth Science simulations and environmental/territorial advertising.

Geomorphological map of a coastal stretch of north-eastern Gozo (Maltese archipelago, Mediterranean Sea)

NASA Astrophysics Data System (ADS)

Soldati, Mauro; Micallef, Anton; Biolchi, Sara; Chelli, Alessandro; Cuoghi, Alessandro; Devoto, Stefano; Gauci, Christopher; Graff, Kevin; Lolli, Federico; Mantovani, Matteo; Mastronuzzi, Giuseppe; Pisani, Luca; Prampolini, Mariacristina; Restall, Brian; Roulland, Thomas; Saliba, Michael; Selmi, Lidia; Vandelli, Vittoria

2017-04-01

Geomorphological investigations carried out along the north-eastern coast of the Island of Gozo (Malta) have led to the production of a detailed geomorphological map. Field surveys, accompanied by aerial photo-interpretation, were carried out within the framework of the EUR-OPA Major Hazards Agreement Project ``Developing Geomorphological mapping skills and datasets in anticipation of subsequent Susceptibility, Vulnerability, Hazard and Risk Mapping'' (Council of Europe). In particular, this geomorphological map is the main output of a `Training Course on Geomorphological Mapping in Coastal Areas' held within the Project in November 2016. The study area selected was between Ramla Bay and Dacrhlet Qorrot Bay on the Island of Gozo (67 km2), part of the Maltese archipelago in the central Mediterranean Sea. From a geological viewpoint, the stratigraphic sequence includes Late Oligocene (Chattian) to Late Miocene (Messinian) sedimentary rocks. The hard limestones of the Upper Coralline Limestone Formation, the youngest lithostratigraphic unit, dominate the study area. Underlying this formation, marls and clays belonging to the Blue Clay Formation extensively outcrop. The oldest lithostratigraphic unit observed in the study area is the Globigerina Limestone Formation, a fine-grained limestone. The lithostructural features of the outcropping units clearly condition the morphography of the landscape. The coast is characterised by the alternation of inlets and promontories. Worthy of notice is the large sandy beach of Ramla Bay partly backed by dunes. From a geomorphological perspective, the investigated coastal stretch is characterised by limestone plateaus bounded by steep structural scarps which are reshaped by gravitational and/or degradation processes, and milder slopes in Blue Clays at their foot comprising of numerous rock block deposits (rdum in Maltese) and active or abandoned terraced fields used for agricultural purposes. Landforms and processes related to structural, gravitational, coastal, alluvial and karst processes were mapped. Particular attention was devoted to the recognition and classification of landslides of different type (in particular block slides and earth flows/slides) which affect large sectors of the north-eastern coast of Gozo. In most cases, landslide accumulations reach the coastline and cover shore platforms. In addition, wide portions of the plateau areas are affected by rock spreading related to the presence of limestones overlying clayey terrains. The climatic conditions, the dense joint systems and the karstification of limestone determine a temporary superficial drainage pattern. Temporary streambeds (wieden in Maltese) were identified in correspondence of V-shaped valleys once occupied by permanent water courses. Karst processes widely affect the Upper Coralline Limestone Formation resulting in caves, diffuse solution pools, grooves and furrows. The geomorphological map output represents a baseline document on which to undertake, first the landslide susceptibility mapping, subsequently the hazard mapping and finally the risk mapping, a critical part of the wider-scoped risk management process of this and similar coastal areas.

The use of multibeam backscatter intensity data as a tool for mapping glacial deposits in the Central North Sea, UK

NASA Astrophysics Data System (ADS)

Stewart, Heather; Bradwell, Tom

2014-05-01

Multibeam backscatter intensity data acquired offshore eastern Scotland and north-eastern England have been used to map drumlin fields, large arcuate moraine ridges, smaller scale moraine ridges, and incised channels on the sea floor. The study area includes the catchments of the previously proposed, but only partly mapped, Strathmore, Forth-Tay, and Tweed palaeo-ice streams. The ice sheet glacial landsystem is extremely well preserved on the sea bed and comprehensive mapping of the seafloor geomorphology has been undertaken. The authors demonstrate the value in utilising not only digital terrain models (both NEXTMap and multibeam bathymetry derived) in undertaking geomorphological mapping, but also examining the backscatter intensity data that is often overlooked. Backscatter intensity maps were generated using FM Geocoder by the British Geological Survey. FM Geocoder corrects the backscatter intensities registered by the multibeam echosounder system, and then geometrically corrects and positions each acoustic sample in a backscatter mosaic. The backscatter intensity data were gridded at the best resolution per dataset (between 2 and 5 m). The strength of the backscattering is dependent upon sediment type, grain size, survey conditions, sea-bed roughness, compaction and slope. A combination of manual interpretation and semi-automated classification of the backscatter intensity data (a predictive method for mapping variations in surficial sea-bed sediments) has been undertaken in the study area. The combination of the two methodologies has produced a robust glacial geomorphological map for the study area. Four separate drumlin fields have been mapped in the study area indicative of fast-flowing and persistent ice-sheet flow configurations. A number of individual drumlins are also identified located outside the fields. The drumlins show as areas of high backscatter intensity compared to the surrounding sea bed, indicating the drumlins comprise mixed sediments of gravelly sands and sandy gravels compared to the surrounding sandy and muddy sediments. Moraines are indicated as areas of high backscatter intensity and comprise coarse grained sediments. A range of moraine sizes have been identified from large scale moraines reflecting both frontal still stands or re-advances of the ice-sheet margin, de geer moraines and smaller moraines that may represent annual variations. Meltwater channels and tunnel valleys are revealed as areas of low backscatter intensity reflecting post-glacial soft sediment infill of the depressions incised into coarser grained and higher strength glacial deposits by these features.

Geomatics for Mapping of Groundwater Potential Zones in Northern Part of the United Arab Emiratis - Sharjah City

NASA Astrophysics Data System (ADS)

Al-Ruzouq, R.; Shanableh, A.; Merabtene, T.

2015-04-01

In United Arab Emirates (UAE) domestic water consumption has increased rapidly over the last decade. The increased demand for high-quality water, create an urgent need to evaluate the groundwater production of aquifers. The development of a reasonable model for groundwater potential is therefore crucial for future systematic developments, efficient management, and sustainable use of groundwater resources. The objective of this study is to map the groundwater potential zones in northern part of UAE and assess the contributing factors for exploration of potential groundwater resources. Remote sensing data and geographic information system will be used to locate potential zones for groundwater. Various maps (i.e., base, soil, geological, Hydro-geological, Geomorphologic Map, structural, drainage, slope, land use/land cover and average annual rainfall map) will be prepared based on geospatial techniques. The groundwater availability of the basin will qualitatively classified into different classes based on its hydro-geo-morphological conditions. The land use/land cover map will be also prepared for the different seasons using a digital classification technique with a ground truth based on field investigation.

Spatial differences in drought vulnerability

NASA Astrophysics Data System (ADS)

Perčec Tadić, M.; Cindić, K.; Gajić-Čapka, M.; Zaninović, K.

2012-04-01

Drought causes the highest economic losses among all hydro-meteorological events in Croatia. It is the most frequent hazard, which produces the highest damages in the agricultural sector. The climate assessment in Croatia according to the aridity index (defined as the ratio of precipitation and potential evapotranspiration) shows that the susceptibility to desertification is present in the warm part of the year and it is mostly pronounced in the Adriatic region and the eastern Croatia lowland. The evidence of more frequent extreme drought events in the last decade is apparent. These facts were motivation to study the drought risk assessment in Croatia. One step in this issue is the construction of the vulnerability map. This map is a complex combination of the geomorphologic and climatological inputs (maps) that are presumed to be natural factors which modify the amount of moisture in the soil. In this study, the first version of the vulnerability map is followed by the updated one that additionally includes the soil types and the land use classes. The first input considered is the geomorphologic slope angle calculated from the digital elevation model (DEM). The SRTM DEM of 100 m resolution is used. The steeper slopes are more likely to lose water and to become dryer. The second climatological parameter, the solar irradiation map, gives for the territory of Croatia the maximum irradiation on the coast. The next meteorological parameter that influences the drought vulnerability is precipitation which is in this assessment included through the precipitation variability expressed by the coefficient of variation. Larger precipitation variability is related with the higher drought vulnerability. The preliminary results for Croatia, according to the recommended procedure in the framework of Drought Management Centre for Southeastern Europe (DMCSEE project), show the most sensitive areas to drought in the southern Adriatic coast and eastern continental lowland.

Evaluation of groundwater potential using geospatial techniques

NASA Astrophysics Data System (ADS)

Hussein, Abdul-Aziz; Govindu, Vanum; Nigusse, Amare Gebre Medhin

2017-09-01

The issue of unsustainable groundwater utilization is becoming increasingly an evident problem and the key concern for many developing countries. One of the problems is the absence of updated spatial information on the quantity and distribution of groundwater resource. Like the other developing countries, groundwater evaluation in Ethiopia has been usually conducted using field survey which is not feasible in terms of time and resource. This study was conducted in Northern Ethiopia, Wollo Zone, in Gerardo River Catchment district to spatially delineate the groundwater potential areas using geospatial and MCDA tools. To do so, eight major biophysical and environmental factors like geomorphology, lithology, slope, rainfall, land use land cover (LULC), soil, lineament density and drainage density were considered. The sources of these data were satellite image, digital elevation model (DEM), existing thematic maps and metrological station data. Landsat image was used in ERDAS Imagine to drive the LULC of the area, while the geomorphology, soil, and lithology of the area were identified and classified through field survey and digitized from existing maps using the ArcGIS software. The slope, lineament and drainage density of the area were derived from DEM using spatial analysis tools. The rainfall surface map was generated using the thissen polygon interpolation. Finally, after all these thematic maps were organized, weighted value determination for each factor and its field value was computed using IDRSI software. At last, all the factors were integrated together and computed the model using the weighted overlay so that potential groundwater areas were mapped. The findings depicted that the most potential groundwater areas are found in the central and eastern parts of the study area, while the northern and western parts of the Gerado River Catchment have poor potential of groundwater availability. This is mainly due to the cumulative effect of steep topographic and high drainage density. At last, once the potential groundwater areas were identified, cross validation of the resultant model was carefully carried out using existing data of dung wells and bore holes. The point data of dung wells and bore holes were overlaid on groundwater potential suitability map and coincide with the expected values. Generally, from this study, it can be concluded that RS and GIS with the help of MCDA are important tools in monitoring and evaluation of groundwater resource potential areas.

GIS- and field based mapping of geomorphological changes in a glacier retreat area: A case study from the Kromer valley, Silvretta Alps (Austria)

NASA Astrophysics Data System (ADS)

Guttmann, Markus; Pöppl, Ronald

2017-04-01

Global warming results in an ongoing retreat of Alpine glaciers, leaving behind large amounts of easily erodible sediments. As a consequence processes like rockfalls, landslides and debris flows as well as fluvial processes occur more frequently in pro- and paraglacial areas, often involving catastrophic consequences for humans and infrastructure in the affected valleys. The main objective of the presented work was to map and spatially quantify glacier retreat and geomorphological changes in the Kromer valley, Silvretta Alps (Austria) by applying GIS- and field-based geomorphological mapping. In total six geomorphological maps (1950s, 1970s, 2001, 2006, 2012, and 2016) were produced and analyzed in the light of the study aim. First results have shown a significant decrease of total glaciated area from 96 ha to 53 ha which was accompanied by increased proglacial geomorphic activity (i.e. fluvial processes, rockfalls, debris flows, shallow landslides) in the last 15 years. More detailed results will be presented at the EGU General Assembly 2017.

Geomorphodiversity index: Quantifying the diversity of landforms and physical landscape.

PubMed

Melelli, Laura; Vergari, Francesca; Liucci, Luisa; Del Monte, Maurizio

2017-04-15

The physical landscape is the mosaic resulting from a wide spectrum of environmental components. The landforms define the variety, or diversity, of the geomorphological component: the geomorphodiversity. Landforms are usually represented in thematic maps where the scale and the graphic solutions are widely heterogeneous. Since geomorphological maps are not always easy to obtain and standardize, topography might be used as a proxy to infer the morphological signature. To recognize, evaluate, and in some cases promote the geomorphodiversity of an area, a numerical assessment is preferable. Through the use of quantitative approaches, indexes can be defined which quantitatively characterize the physical landscape in a discretized space consisting of continuous and regular cells. In this approach each cell is labelled with an algebraic value, which increases with the diversity degree. In this paper a quantitative index for geomorphodiversity is estimated stressing the topographic variables derived from Digital Elevation Models in a GIS environment. The resulting index is the sum of the variety of each terrain parameter taken into account. The areas characterized by the highest value of geomorphodiversity index show a good correspondence with well-known situations in the region where not always the geological heritage is properly acknowledged. The areas characterized by the lowest value of geodiversity correspond to the center of some intermountain basins of the region. Being the index strictly related to the topographic variety, this result is quite obvious but not easily predictable since in some flat areas the index is higher. Comparing the results with the geomorphological map of the area performs a validation procedure for the method. A positive correlation is found between the index calculated and the presence/absence of landforms. The paper shows that the index is a useful and simple tool for the identification, analysis and promotion of the geological heritage. Copyright © 2017. Published by Elsevier B.V.

GIS-based modeling of debris flow processes in an Alpine catchment, Antholz valley, Italy

NASA Astrophysics Data System (ADS)

Sandmeier, Christine; Damm, Bodo; Terhorst, Birgit

2010-05-01

Debris flows are frequent natural hazards in mountain regions, which seriously can threat human lives and economic values. In the European Alps the occurrence of debris flows might even increase with respect to climate change, including permafrost degradation, glacier retreat and variable precipitation patterns. Thus, detailed understanding of process parameters and spatial distribution of debris flows is necessary to take appropriate protection measures for risk assessment. In this context, numerical models have been developed and applied successfully for simulation and prediction of debris-flow hazards and related process areas. In our study a GIS-based model is applied in an alpine catchment to address the following questions: Where are potential initiating areas of debris flows? How much material can be mobilized? What is the influence of topography and precipitation? The study area is located in the Antholz valley in the eastern Alps of Northern Italy. The investigated catchment of the Klammbach creek comprises 6.5 km² and is divided into two sub-catchments. Geologically it is dominated by metamorphic rock and altitudes range between 1310 and 3270 m. In summer 2005 a debris flow of more than 100000 m³ took place, originating from a steep, sparsely vegetated debris cone in the western part of the catchment. According to a regional study, the lower permafrost boundary in this area has risen by 250 m. In a first step, during a field survey, geomorphological mapping was performed, several channel cross-sections were measured and sediment samples were taken. Using mapping results and aerial images, a geomorphological map was created. In further steps, results from the field work, the geomorphological map and existing digital data sets, including a digital elevation model with 2.5 m resolution, are used to derive input data for the modeling of debris flow processes. The model framework ‘r.debrisflow' based on GRASS GIS is applied (Mergili, 2008*), as it is capable of simulating the potential spatial patterns of debris flow deposition, as well as their initiation and movement. Furthermore it is a freely available and opensource software and can thus be improved and extended. ‘r.debrisflow' couples a hydraulic, a slope stability, a sediment transport and a debris flow runout model, which are combined differently in 6 simulation modes. In a first step, model parameters are calibrated using the runout only mode with known parameters of the 2005 debris flow. Finally, the full mode will be used to evaluate the debris-flow potential of the whole catchment. First results from the geomorphological mapping reveal numerous surface forms, like levees, debris flow lobes or scars that indicate past and recent debris flow activity in the area. In both sub-catchments, there are large areas of unconsolidated, sparsely or unvegetated sediments, surrounded by high rock walls, which conduct precipitation rapidly into the debris. The two sub-catchments, however, have different topographic characteristics, which can be analyzed with the model in more detail. In a next step, the potential starting areas of future debris flows shall be identified and the potential amount of mobilized material shall be estimated by the model. *Mergili, M. (2008): Integrated modelling of debris flows with Open Source GIS. Ph.D. thesis. University of Innsbruck. http://www.uibk.ac.at/geographie/personal/mergili/dissertation.pdf

Digital Elevation Models of the Earth derived from space-based observations: Advances and potential for geomorphological studies

NASA Astrophysics Data System (ADS)

Mouratidis, Antonios

2013-04-01

Digital Elevation Models (DEMs) are an inherently interdisciplinary topic, both due to their production and validation methods, as well as their significance for numerous disciplines. The most utilized contemporary topographic datasets worldwide are those of global DEMs. Several space-based sources have been used for the production of (almost) global DEMs, namely satellite Synthetic Aperture Radar (SAR) Interferometry/InSAR, stereoscopy of multispectral satellite images and altimetry, producing several versions of autonomous or mixed products (i.e. SRTM, ACE, ASTER-GDEM). Complementary space-based observations, such as those of Global Navigation Satellite Systems (GNSS), are also used, mainly for validation purposes. The apparent positive impact of these elevation datasets so far has been consolidated by the plethora of related scientific, civil and military applications. Topography is a prominent element for almost all Earth sciences, but in Geomorphology it is even more fundamental. In geomorphological studies, elevation data and thus DEMs can be extensively used for the extraction of both qualitative and quantitative information, such as relief classification, determination of slope and slope orientation, delineation of drainage basins, extraction of drainage networks and much more. Global DEMs are constantly becoming finer, i.e. of higher spatial resolution and more "sensitive" to elevation changes, i.e. of higher vertical accuracy and these progresses are undoubtedly considered as a major breakthrough, each time a new improved global DEM is released. Nevertheless, for Geomorphology in particular, if not already there, we are close to the point in time, where the need for discrimination between DSM (Digital Surface Model) and DTM (Digital Terrain Model) is becoming critical; if the distinction between vegetation and man-made structures on one side (DSM), and actual terrain elevation on the other side (DTM) cannot be made, then, in many cases, any further increase of elevation accuracy in DEMs will have little impact on geomorphological studies. After shortly reviewing the evolution of satellite-based global DEMs, the purpose of this paper is to address their current limitations and challenges from the perspective of a geomorphologist. Subsequently, the implications for geomorphological studies are discussed, with respect to the expected near-future advances in the field, such as the TanDEM-X Global Digital Elevation Model ("WorldDEM", 2014), as well as spaceborne LIDAR (Light Detection and Ranging) approaches (e.g. Lidar Surface Topography/LIST mission, 2016-2020).

Modelling soil erosion in a head catchment of Jemma Basin on the Ethiopian highlands

NASA Astrophysics Data System (ADS)

Cama, Mariaelena; Schillaci, Calogero; Kropáček, Jan; Hochschild, Volker; Maerker, Michael

2017-04-01

Soil erosion represents one of the most important global issues with serious effects on agriculture and water quality especially in developing countries such as Ethiopia where rapid population growth and climatic changes affect wide mountainous areas. The catchment of Andit-Tid is a head catchment of Jemma Basin draining to the Blue Nile (Central Ethiopia). It is located in an extremely variable topographical environment and it is exposed to high degradation dynamics especially in the lower part of the catchment. The increasing agricultural activity and grazing, lead to an intense use of the steep slopes which altered the soil structure. As a consequence, water erosion processes accelerated leading to the evolution of sheet erosion, gullies and badlands. This study is aimed at a geomorphological assessment of soil erosion susceptibility. First, a geomorphological map is generated using high resolution digital elevation model (DEM) derived from high resolution stereoscopic satellite data, multispectral imagery from Rapid Eye satellite system . The map was then validated by a detailed field survey. The final maps contains three inventories of landforms: i) sheet, ii) gully erosion and iii) badlands. The water erosion susceptibility is calculated with a Maximum Entropy approach. In particular, three different models are built using the three inventories as dependent variables and a set of spatial attributes describing the lithology, terrain, vegetation and land cover from remote sensing data and DEMs as independent variables. The single susceptibility maps for sheet, gully erosion as well as badlands showed good to excellent predictive performances. Moreover, we reveal and discuss the importance of different sets of variables among the three models. In order to explore the mutual overlap of the three susceptibility maps we generated a combined map as color composite whereas each color represents one component of water erosion. The latter map yield a useful information for land use managers and planning purposes.

Geodiversity of the Umbria region (central Italy): a GIS-based quantitative index

NASA Astrophysics Data System (ADS)

Melelli, Laura; Pica, Alessia; Del Monte, Maurizio

2014-05-01

The measure of natural range related to geological bedrock, landforms and geomorphological processes is the necessary starting point to geodiversity evaluation. Geodiversity plays a strategic role in landscape management. Whereas geotourism and geosites are identified as a driving power for the scientific and economic promotion of an area, the geodiversity knowledge is required for a complete and accurate research. For example, high values of this abiotic parameter identify and support the foundation of geoparks. According to this perspective, the geodiversity is the unifying factor for these areas of interest. While a subjective and qualitative approach may be adequate for geosites definition, identification and cultural promotion, the geodiversity concept needs a different evaluation method. A quantitative procedure allows achieving an objective and repeatable process exportable in different geographic units. Geographical Information Systems and spatial analysis techniques are the base to quantitative evaluation involving topographic, geological and geomorphological data. Therefore, the assessment of a numerical index derived from the overlay of spatial parameters can be conveniently computed in GIS environment. In this study, a geodiversity index is proposed where geological, geomorphological and landcover factors deriving mainly from maps and field survey; topographic ones are employed from DEM and remote sensed data. Each abiotic parameter is modelled in a grid format; focal functions do provide neighbourhood analysis and computing variety statistics. A particular extent is dedicated to topographic information and terrain roughness, that are strictly related to efficiency of geomorphological processes and generally corresponding to the abiotic components variability. The study area is located in central Italy and is characterized by a well known natural heritage. Thirty-seven geosites are detected in the Umbria region, where seven regional and one natural parks are present. All the area shows a strong correlation between the geological setting and the relief energy associated to topography assessment. Three main outcrop complexes are present: a fluvial lacustrine, where the lowest slope values and plain area are widespread; a terrigenous one, with a medium slope value; and a calcareous complex corresponding to the mountain areas and the highest amplitude of relief. This partition matches different geomorphological processes and landforms, ensuring a widespread distribution of geodiversity. The final map is a digital data that localizes areas with, respectively, null or minimum, medium, and high geodiversity values. The highest class overlaps to geosites areas, to high values of amplitude of relief and where the geomorphological processes are more effective and various. This confirms the method accuracy. The results obtained represent an important advancement in geodiversity research and a significant instrument for economic development and conservation management.

Digital image enhancement techniques used in some ERTS application problems. [geology, geomorphology, and oceanography

NASA Technical Reports Server (NTRS)

Goetz, A. F. H.; Billingsley, F. C.

1974-01-01

Enhancements discussed include contrast stretching, multiratio color displays, Fourier plane operations to remove striping and boosting MTF response to enhance high spatial frequency content. The use of each technique in a specific application in the fields of geology, geomorphology and oceanography is demonstrated.

A Detailed Geomorphological Sketch Map of Titan's Afekan Crater Region

NASA Astrophysics Data System (ADS)

Schoenfeld, A.; Malaska, M. J.; Lopes, R. M. C.; Le Gall, A. A.; Birch, S. P.; Hayes, A.

2014-12-01

Due to Titan's uniquely thick atmosphere and organic haze layers, the most detailed images (with resolution of 300 meters per pixel) of the Saturnian moon's surface exist as Synthetic Aperture Radar (SAR) images taken by Cassini's RADAR instrument. Using the SAR data, we have been putting together detailed geomorphological sketch maps of various Titan regions in an effort to piece together its geologic history. We initially examined the Afekan region of Titan due to extensive SAR coverage. Features described on Afekan fall under the categories (in order of geologic age, extrapolated from their relative emplacement) of hummocky, labyrinthic, plains, and dunes. During our mapping effort, we also divided each terrain category into several different subclasses on a local level. Our map offers a chance to present and analyze the distribution, relationship, and potential formation hypotheses of the different terrains. In bulk, we find evidence for both Aeolian and fluvial processes. A particularly important unit found in the Afekan region is the unit designated "undifferentiated plains", or the "Blandlands" of Titan, a mid-latitude terrain unit comprising 25% of the moon's surface. Undifferentiated plains are notable for its relative featurelessness in radar and infrared. Our interpretation is that it is a fill unit in and around Afekan crater and other hummocky/mountainous units. The plains suggest that the nature of Titan's geomorphology seems to be tied to ongoing erosional forces and sediment deposition. Other datasets used in characterizing Titan's various geomorphological units include information obtained from radiometry, infrared (ISS), and spectrometry (VIMS). We will present the detailed geomorphological sketch map with all the terrain units assigned and labeled.

Directions in Geoheritage Studies: Suggestions from the Italian Geomorphological Community

NASA Astrophysics Data System (ADS)

Panizza, Valeria

2015-04-01

More and more attention has been focused on geological and geomorphological heritage in the past years, leading to several researches in the framework of conservation projects, both at administrative and at scientific level, involving national and international research groups whose purposes are the promotion of Earth Sciences knowledge and the conservation of geological heritage. This paper presents an overview of research and conservation projects in Italy, mainly focused on the geomorphological heritage. Members of the AIGEO Working Group on geomorphosites and cultural landscape analyzed the historical development, methodological issues and main results of these research projects in order to identify possible innovation lines to improve the awareness and knowledge on geodiversity and geoheritage by a wide public, including education, tourism and conservation sectors. In Italy numerous projects of research have been realized with the main aim of geomorphosites inventory and the proposal of assessment methodologies, and so to the improvement and to the analysis of risks and impacts related to their fruition. At an international level, many Italian researchers have also been involved in studies carried out in the Working Group "Geomorphological sites" of the International Association of Geomorphologists (IAG). At a national level several research lines are under development, offering different responses to methodological issues within the general topic of geodiversity and geoheritage: Geosites inventories and assessment activities are performed with powerful digital techniques and new reference models: among these, the investigation on the ecologic support role for increasing geomorphosites global value and the elaboration of quantitative assessment methods of the scientific quality of Geomorphosites, carried out specifically for territorial planning. Improvements in field data collection and visual representation of landforms lead to new findings in geomorphological mapping; by making use of both traditional paper maps and computer-elaborated documents produced by GIS new visual products for geotourism have been created. Geomorphological heritage is now analysed with a special focus on its relationships with cultural landscape and human history; integrated studies of natural and cultural landscapes allow development of better itineraries for geotourism. Quantitative selection of geomorphosites and definition of global value of geotouristic trails according to dedicated relational database are performed with a focus on monitoring of evolution rates of active geomorphosites in different morphoclimatic contexts in order to evaluate the risk scenarios in touristic contexts. Development of innovative educational strategies for the dissemination of scientific research results on geomorphosites includes extensive use of multimedia and Web technologies. More and more detailed reconstruction of the recent evolutionary stages of the geomorphological landscape are performed by means of collaborative investigations performed by geomorphologists, geoarcheologists, archeologists. Relationships between geomorphological heritage and parks are now a comprehensive development, including the proposal of interdisciplinary attractions such as geoarcheological parks, mining and other georesources thematic parks. Geomorphosites are now selected with a particular attention to targeted climatic conditions and environments, such as glacial and periglacial environments, karsts lands.

From field data collection to earth sciences dissemination: mobile examples in the digital era

NASA Astrophysics Data System (ADS)

Giardino, Marco; Ghiraldi, Luca; Palomba, Mauro; Perotti, Luigi

2015-04-01

In the framework of the technological and cultural revolution related to the massive diffusion of mobile devices, as smartphones and tablets, the information management and accessibility is changing, and many software houses and developer communities realized applications that can meet various people's needs. Modern collection, storing and sharing of data have radically changed, and advances in ICT increasingly involve field-based activities. Progresses in these researches and applications depend on three main components: hardware, software and web system. Since 2008 the geoSITLab multidisciplinary group (Earth Sciences Department and NatRisk Centre of the University of Torino and the Natural Sciences Museum of the Piemonte Region) is active in defining and testing methods for collecting, managing and sharing field information using mobile devices. Key issues include: Geomorphological Digital Mapping, Natural Hazards monitoring, Geoheritage assessment and applications for the teaching of Earth Sciences. An overview of the application studies is offered here, including the use of Mobile tools for data collection, the construction of relational databases for inventory activities and the test of Web-Mapping tools and mobile apps for data dissemination. The fil rouge of connection is a standardized digital approach allowing the use of mobile devices in each step of the process, which will be analysed within different projects set up by the research group (Geonathaz, EgeoFieldwork, Progeo Piemonte, GeomediaWeb). The hardware component mainly consists of the availability of handheld mobile devices (e.g. smartphones, PDAs and Tablets). The software component corresponds to applications for spatial data visualization on mobile devices, such as composite mobile GIS or simple location-based apps. The web component allows the integration of collected data into geodatabase based on client-server architecture, where the information can be easily loaded, uploaded and shared between field staff and data management team, in order to disseminate collected information to media or to inform the decision makers. Results demonstrated the possibility to record field observations in a fast and reliable way, using standardized formats that can improve the precision of collected information and lower the possibility of errors and data omission. Dedicated forms have been set up for gathering different thematic data (geologic/geomorphologic, faunal and floristic, path system…etc.). Field data allowed to arrange maps and SDI useful for many application purposes: from country-planning to disaster risk management, from Geoheritage management to Earth Science concepts dissemination.

Modelling prehistoric terrain Models using LiDAR-data: a geomorphological approach

NASA Astrophysics Data System (ADS)

Höfler, Veit; Wessollek, Christine; Karrasch, Pierre

2015-10-01

Terrain surfaces conserve human activities in terms of textures and structures. With reference to archaeological questions, the geological archive is investigated by means of models regarding anthropogenic traces. In doing so, the high-resolution digital terrain model is of inestimable value for the decoding of the archive. The evaluation of these terrain models and the reconstruction of historical surfaces is still a challenging issue. Due to the data collection by means of LiDAR systems (light detection and ranging) and despite their subsequent pre-processing and filtering, recently anthropogenic artefacts are still present in the digital terrain model. Analysis have shown that elements, such as contour lines and channels, can well be extracted from a high-resolution digital terrain model. This way, channels in settlement areas show a clear anthropogenic character. This fact can also be observed for contour lines. Some contour lines representing a possibly natural ground surface and avoid anthropogenic artefacts. Comparable to channels, noticeable patterns of contour lines become visible in areas with anthropogenic artefacts. The presented workflow uses functionalities of ArcGIS and the programming language R.1 The method starts with the extraction of contour lines from the digital terrain model. Through macroscopic analyses based on geomorphological expert knowledge, contour lines are selected representing the natural geomorphological character of the surface. In a first step, points are determined along each contour line in regular intervals. This points and the corresponding height information which is taken from an original digital terrain model is saved as a point cloud. Using the programme library gstat, a variographic analysis and the use of a Kriging-procedure based on this follow.2-4 The result is a digital terrain model filtered considering geomorphological expert knowledge showing no human degradation in terms of artefacts, preserving the landscape-genetic character and can be called a prehistoric terrain model.

Mapping of land use and geomorphology in the APAPORE project area by LANDSAT satellite data, volume 1

NASA Technical Reports Server (NTRS)

Parada, N. D. J. (Principal Investigator); Dossantos, A. P.; Kux, H. J.; Sausen, T. M.; Bueno, A. M. T. R.; Desouza, L. F.; Nunes, J. S. D.

1982-01-01

The results of a land use and geomorphological mapping of the so-called Projeto APAPORE area, at Mato Grosso do Sul State are presented. The study was carried out using multispectral scanner (MSS) and return beam vidicon LANDSAT images (channels 5 and 7 for the MSS) at the scale of 1:250,000 from 1980 through visual interpretation. The results indicate that pastureland is the most widespead class and that the agricultural areas re concentrated in the north of the area under study. The area covered with cerradao (arboreous savanna type) has a great areal extention, thus permitting the advance of the agricultural frontier. The geomorphological mapping can be useful to regional planning of future land use within the studied area.

A multi-annual landslide inventory for the assessment of shallow landslide susceptibility - Two test cases in Vorarlberg, Austria

NASA Astrophysics Data System (ADS)

Zieher, Thomas; Perzl, Frank; Rössel, Monika; Rutzinger, Martin; Meißl, Gertraud; Markart, Gerhard; Geitner, Clemens

2016-04-01

Geomorphological landslide inventories provide crucial input data for any study on the assessment of landslide susceptibility, hazard or risk. Several approaches for assessing landslide susceptibility have been proposed to identify areas particularly vulnerable to this natural hazard. What they have in common is the need for data of observed landslides. Therefore the first step of any study on landslide susceptibility is usually the compilation of a geomorphological landslide inventory using a geographical information system. Recent research has proved the feasibility of orthophoto interpretation for the preparation of an inventory aimed at the delineation of landslides with the use of distinctive signs in the imagery data. In this study a multi-annual landslide inventory focusing on shallow landslides (i.e. translational soil slides of 0-2 m in depth) was compiled for two study areas in Vorarlberg (Austria) from the interpretation of nine orthophoto series. In addition, derivatives of two generations of airborne laser scanning data aided the mapping procedure. Landslide scar areas were delineated on the basis of a high-resolution differential digital terrain model. The derivation of landslide volumes, depths and depth-to-length ratios are discussed. Results show that most mapped landslides meet the definition of a shallow landslide. The inventory therefore provides the data basis for the assessment of shallow landslide susceptibility and allows for the application of various modelling techniques.

Ecological-geomorphological assessment of the suburban area of Astana

NASA Astrophysics Data System (ADS)

Akiyanova, F. Zh; Zinabdin, N. B.; Kenzhebayeva, A. Zh; Adilbekova, F. G.; Ilyassova, A. T.; Karakulov, E. M.

2018-01-01

The results of ecological-geomorphological assessment of the suburban zone of Astana is presented in the paper. Climatic and hydrological factors, which are the agents of pollutants’ transport and caused the development of exogenous processes in the suburban area of Astana were studied and mapped. On the base of the geoinformation technologies and field studies the geomorphologic structure and morphogenetic processes were studied. The analysis of the data complex led to assess ecological-geomorphological conditions of the suburban area of Astana.

Ultra-Fine Scale Spatially-Integrated Mapping of Habitat and Occupancy Using Structure-From-Motion.

PubMed

McDowall, Philip; Lynch, Heather J

2017-01-01

Organisms respond to and often simultaneously modify their environment. While these interactions are apparent at the landscape extent, the driving mechanisms often occur at very fine spatial scales. Structure-from-Motion (SfM), a computer vision technique, allows the simultaneous mapping of organisms and fine scale habitat, and will greatly improve our understanding of habitat suitability, ecophysiology, and the bi-directional relationship between geomorphology and habitat use. SfM can be used to create high-resolution (centimeter-scale) three-dimensional (3D) habitat models at low cost. These models can capture the abiotic conditions formed by terrain and simultaneously record the position of individual organisms within that terrain. While coloniality is common in seabird species, we have a poor understanding of the extent to which dense breeding aggregations are driven by fine-scale active aggregation or limited suitable habitat. We demonstrate the use of SfM for fine-scale habitat suitability by reconstructing the locations of nests in a gentoo penguin colony and fitting models that explicitly account for conspecific attraction. The resulting digital elevation models (DEMs) are used as covariates in an inhomogeneous hybrid point process model. We find that gentoo penguin nest site selection is a function of the topography of the landscape, but that nests are far more aggregated than would be expected based on terrain alone, suggesting a strong role of behavioral aggregation in driving coloniality in this species. This integrated mapping of organisms and fine scale habitat will greatly improve our understanding of fine-scale habitat suitability, ecophysiology, and the complex bi-directional relationship between geomorphology and habitat use.

Last Glacial-Interglacial Transition ice dynamics in the Wicklow Mountains, Ireland

NASA Astrophysics Data System (ADS)

Knight, Lauren; Boston, Clare; Lovell, Harold; Pepin, Nick

2017-04-01

Understanding of the extent and dynamics of former ice masses in the Wicklow Mountains, Ireland, during the Last Glacial-Interglacial Transition (LGIT; 15-10 ka BP) is currently unresolved. Whilst it is acknowledged that the region hosted a local ice cap within the larger British-Irish Ice Sheet at the Last Glacial Maximum (LGM; 27 ka BP), there has been little consideration of ice cap disintegration to a topographically constrained ice mass during the LGIT. This research has produced the first regional glacial geomorphological map, through remote sensing (aerial photograph and digital terrain model interrogation) and field mapping. This has allowed both the style and extent of mountain glaciation and ice recession dynamics during the LGIT to be established. This geomorphological mapping has highlighted that evidence for local glaciation in the Wicklow Mountains is more extensive than previously recognised, and that small icefields and associated outlet valley glaciers existed during the LGIT following disintegration of the Wicklow Ice Cap. A relative chronology based on morphostratigraphic principles is developed, which indicates complex patterns of ice mass oscillation characterised by periods of both sustained retreat and minor readvance. Variations in the pattern of recession across the Wicklow Mountains are evident and appear to be influenced, in part, by topographic controls (e.g. slope, aspect, glacier hypsometry). In summary, this research establishes a relative chronology of glacial events in the region during the LGIT and presents constraints on ice mass extent, dynamics and retreat patterns, offering an insight into small ice mass behaviour in a warming climate.

Capability of applying morphometric parameters of relief in river basins for geomorphological zoning of a territory

NASA Astrophysics Data System (ADS)

Ivanov, M. A.; Yermolaev, O. P.

2018-01-01

Information about morphometric characteristics of relief is necessary for researches devoted to geographic characteristics of territory, its zoning, assessment of erosion processes, geoecological condition and others. For the Volga Federal District for the first time a spatial database of geomorphometric parameters 1: 200 000 scale was created, based on a river basin approach. Watersheds are used as a spatial units created by semi-automated method using the terrain and hydrological modeling techniques implemented in the TAS GIS and WhiteBox GIS. As input data DEMs SRTM and Aster GDEM and hydrographic network vectorized from topographic maps were used. Using DEM highlighted above for each river basin, basic morphometric relief characteristics such as mean height, slope steepness, slope length, height range, river network density and factor LS were calculated. Basins belonging to the geomorphological regions and landscape zones was determined, according to the map of geomorphological zoning and landscape map. Analysis of variance revealed a statistically significant relationship between these characteristics and geomorphological regions and landscape zones. Consequently, spatial trends of changes of analyzed morphometric characteristics were revealed.

Airborne laser scanning for high-resolution mapping of Antarctica

NASA Astrophysics Data System (ADS)

Csatho, Bea; Schenk, Toni; Krabill, William; Wilson, Terry; Lyons, William; McKenzie, Garry; Hallam, Cheryl; Manizade, Serdar; Paulsen, Timothy

In order to evaluate the potential of airborne laser scanning for topographic mapping in Antarctica and to establish calibration/validation sites for NASA's Ice, Cloud and land Elevation Satellite (ICESat) altimeter mission, NASA, the U.S. National Science Foundation (NSF), and the U.S. Geological Survey (USGS) joined forces to collect high-resolution airborne laser scanning data.In a two-week campaign during the 2001-2002 austral summer, NASA's Airborne Topographic Mapper (ATM) system was used to collect data over several sites in the McMurdo Sound area of Antarctica (Figure 1a). From the recorded signals, NASA computed laser points and The Ohio State University (OSU) completed the elaborate computation/verification of high-resolution Digital Elevation Models (DEMs) in 2003. This article reports about the DEM generation and some exemplary results from scientists using the geomorphologic information from the DEMs during the 2003-2004 field season.

Comparing the information content of coral reef geomorphological and biological habitat maps, Amirantes Archipelago (Seychelles), Western Indian Ocean

NASA Astrophysics Data System (ADS)

Hamylton, S.; Andréfouët, S.; Spencer, T.

2012-10-01

Increasing the use of geomorphological map products in marine spatial planning has the potential to greatly enhance return on mapping investment as they are commonly two orders of magnitude cheaper to produce than biologically-focussed maps of benthic communities and shallow substrates. The efficacy of geomorphological maps derived from remotely sensed imagery as surrogates for habitat diversity is explored by comparing two map sets of the platform reefs and atolls of the Amirantes Archipelago (Seychelles), Western Indian Ocean. One mapping campaign utilised Compact Airborne Spectrographic Imagery (19 wavebands, 1 m spatial resolution) to classify 11 islands and associated reefs into 25 biological habitat classes while the other campaign used Landsat 7 + ETM imagery (7 bands, 30 m spatial resolution) to generate maps of 14 geomorphic classes. The maps were compared across a range of characteristics, including habitat richness (number of classes mapped), diversity (Shannon-Weiner statistic) and thematic content (Cramer's V statistic). Between maps, a strong relationship was revealed for habitat richness (R2 = 0.76), a moderate relationship for class diversity and evenness (R2 = 0.63) and a variable relationship for thematic content, dependent on site complexity (V range 0.43-0.93). Geomorphic maps emerged as robust predictors of the habitat richness in the Amirantes. Such maps therefore demonstrate high potential value for informing coastal management activities and conservation planning by drawing on information beyond their own thematic content and thus maximizing the return on mapping investment.

Object-based classification of global undersea topography and geomorphological features from the SRTM30_PLUS data

NASA Astrophysics Data System (ADS)

Dekavalla, Maria; Argialas, Demetre

2017-07-01

The analysis of undersea topography and geomorphological features provides necessary information to related disciplines and many applications. The development of an automated knowledge-based classification approach of undersea topography and geomorphological features is challenging due to their multi-scale nature. The aim of the study is to develop and evaluate an automated knowledge-based OBIA approach to: i) decompose the global undersea topography to multi-scale regions of distinct morphometric properties, and ii) assign the derived regions to characteristic geomorphological features. First, the global undersea topography was decomposed through the SRTM30_PLUS bathymetry data to the so-called morphometric objects of discrete morphometric properties and spatial scales defined by data-driven methods (local variance graphs and nested means) and multi-scale analysis. The derived morphometric objects were combined with additional relative topographic position information computed with a self-adaptive pattern recognition method (geomorphons), and auxiliary data and were assigned to characteristic undersea geomorphological feature classes through a knowledge base, developed from standard definitions. The decomposition of the SRTM30_PLUS data to morphometric objects was considered successful for the requirements of maximizing intra-object and inter-object heterogeneity, based on the near zero values of the Moran's I and the low values of the weighted variance index. The knowledge-based classification approach was tested for its transferability in six case studies of various tectonic settings and achieved the efficient extraction of 11 undersea geomorphological feature classes. The classification results for the six case studies were compared with the digital global seafloor geomorphic features map (GSFM). The 11 undersea feature classes and their producer's accuracies in respect to the GSFM relevant areas were Basin (95%), Continental Shelf (94.9%), Trough (88.4%), Plateau (78.9%), Continental Slope (76.4%), Trench (71.2%), Abyssal Hill (62.9%), Abyssal Plain (62.4%), Ridge (49.8%), Seamount (48.8%) and Continental Rise (25.4%). The knowledge-based OBIA classification approach was considered transferable since the percentages of spatial and thematic agreement between the most of the classified undersea feature classes and the GSFM exhibited low deviations across the six case studies.

Interactions between geomorphology and vegetation in the Western Swiss Alps: first investigations

NASA Astrophysics Data System (ADS)

Giaccone, Elisa; Mariéthoz, Grégoire; Lambiel, Christophe

2017-04-01

The influence of earth surface processes can modify the microhabitat conditions and the species richness, composition and distribution patterns of plant communities. It is therefore important to understand how geomorphology affects the distribution of plant species to predict future vegetation evolution in a context of climate change. To better analyse the influence of geomorphology on vegetation growth in the alpine periglacial belt, we are studying various geomorphological processes (e.g. cryoturbation and solifluction), permafrost, nivation and ground surface characteristics at three focus sites of the Vaud Alps (Western Swiss Alps). The sites are located at an altitude range comprised between 2000 and 2600 m a.s.l. The geomorphology is characterized mainly by the presence of small glaciers, large moraine deposits, rock glaciers and debris slopes. Monitoring of the ground surface temperatures, permafrost mapping, vegetation survey and drone flights have been carried out to investigate in detail the environmental variables. Initial results show a heterogeneous vegetation cover depending on time since deglaciation, debris size, ground stability and soil age. Debris pioneer species are present on moraines, rock glaciers and debris slope; grassland are developed in zones not affected by LIA glacier advances or other interfering processes such as avalanches. The high-resolution images obtained from drone flights (5 cm/pixel) allow a detailed study of the granulometry. In order to use such geomorphological information on a wider area of interest, the local data acquired on focus sites have to be spatialized to a regional scale. This is accomplished by developing an approach based on remote sensing and multiple-point geostatistics that performs a semi-automated geomorphological mapping (SAGM). The SAGM is based on a training image composed by a geomorphological map yet existent, an orthophoto, the slope, the aspect, the curvature, the granulometry classification and the NDVI. The SAGM will be first elaborated for the focus sites and will then be extended to the entire Vaud Alps above 2000 m a.s.l. This information will be used to better understand the geomorphology-vegetation interactions and their spatialization.

Mapping Drought Sensitivity of Ecosystem Functioning in Mountainous Watersheds: Spatial Heterogeneity and Geological-Geomorphological Control

NASA Astrophysics Data System (ADS)

Wainwright, H. M.; Steefel, C. F.; Williams, K. H.; Hubbard, S. S.; Enquist, B. J.; Steltzer, H.; Sarah, T.

2016-12-01

Mountainous watersheds in the Upper Colorado River Basin play a critical role in supplying water and nutrients to western North America. Ecosystem functioning in those regions - including plant dynamics and biogeochemical cycling - is known to be limited by water availability. Under the climate change, early snowmelt and increasing temperature are expected to intensify the drought conditions in early growing seasons. Although the impact of early-season drought has been documented in plot-scale experiments, ascertaining its significance in mountainous watersheds is challenging given the highly heterogeneous nature of the systems with complex terrain and diverse plant functional types (PFTs). The objectives of this study are (1) to map the regions where the plant dynamics are relatively more sensitive to drought conditions based on historical satellite and climate data, and (2) to identify the environmental controls (e.g., geomorphology, elevation, geology, snow and PFT) on drought sensitivity. We characterize the spatial heterogeneity of drought sensitivity in four watersheds (a 15 x 15 km domain) near the Rocky Mountain Biological Laboratory in Colorado, USA. Following previous plot-scale studies, we first define the drought sensitivity based on annual peak NDVI (Landsat 5) and climatic datasets. Non-parametric tree-based machine learning methods are used to identify the significant environmental controls, using high-resolution LiDAR digital elevation map and peak snow-water-equivalent distribution from NASA airborne snow observatory. Results show that the drought sensitivity is negatively correlated with elevation, suggesting increased water limitations in lower elevation (less snow, higher temperature). The drought sensitivity is more spatially variable in shallow-rooted plant types, affected by local hydrological conditions. We also found geomorphological and geological controls, such as high sensitivity in the steep well-drained glacial moraine regions. Our results highlight the importance of geology and subsurface flow conditions, in addition to snow accumulation. In parallel, the remotely-sensed drought sensitivity can be used as a scalable metric to identify the vulnerable regions to the future climate change, as well as to inform future sampling and characterization.

Morphometric analysis of the Marmara Sea river basins, Turkey

NASA Astrophysics Data System (ADS)

Elbaşı, Emre; Ozdemir, Hasan

2014-05-01

The drainage basin, the fundamental unit of the fluvial landscape, has been focus of research aimed at understanding the geometric characteristics of the master channel and its tributary network. This geometry is referred to as the basin morphometry and is nicely reviewed by Abrahams (1984). A great amount of research has focused on geometric characteristic of drainage basins, including the topology of the stream networks, and quantitative description of drainage texture, pattern, shape, and relief characteristics. Evaluation of morphometric parameters necessitates the analysis of various drainage parameters such as ordering of the various streams, measurement of basin area and perimeter, length of drainage channels, drainage density (Dd), stream frequency (Fs), bifurcation ratio (Rb), texture ratio (T), basin relief (Bh), Ruggedness number (Rn), time of concentration (Tc), hypsometric curve and integral (Hc and Hi) (Horton, 1932, Schumn, 1956, Strahler, 1957; Verstappen 1983; Keller and Pinter, 2002; Ozdemir and Bird, 2009). These morphometric parameters have generally been used to predict flood peaks, to assess sediment yield, and to estimate erosion rates in the basins. River basins of the Marmara Sea, has an area of approximately 40,000 sqkm, are the most important basins in Turkey based on their dense populations, industry and transportation systems. The primary aim of this study is to determine and analyse of morphometric characteristics of the Marmara Sea river basins using 10 m resolution Digital Elevation Model (DEM) and to evaluate of the results. For these purposes, digital 10 m contour maps scaled 1:25000 and geological maps scaled 1:100000 were used as the main data sources in the study. 10 m resolution DEM data were created using the contour maps and then drainage networks and their watersheds were extracted using D8 pour point model. Finally, linear, areal and relief morphometries were applied to the river basins using Geographic Information Systems (GIS). This study shows that morphometric analysis of the basins in regional level are very important to understand general morphological characteristics of the basins. In this case, tectonic and lithological conditions of the basins have greatly affected the morphometric characteristics of the north and south basins of the Marmara Sea. References Abrahams, AD. 1984. Channel Networks: A Geomorphological Perspective. Water Resources Research, Volume 20, Issue 2, pages 161-188. Horton, R.E. 1932. Drainage basin characteristics. Trans Am Geophys Union 13:350-361. Keller, E.A., Pinter, N. 2002. Active Tectonics Earthquakes, Uplift, and Landscape, Second Edition, Prentice Hall, New Jersey. Ozdemir H., Bird D. 2009. Evaluation of morphometric parameters of drainage networks derived from topographic maps and DEM in point of floods, Environmental Geology, vol.56, pp.1405-1415. Schumm, S.A. 1956. Evolution of drainage systems and slopes in badlands at Perth Amboy, New Jersey. Geol Soc Am Bull 67:597-646. Strahler, A.N. 1957. Quantitative geomorphology of drainage and channel networks. In: Chow YT (ed) Handbook of appliecl hydrology. Me Graw Hill Book Company, New York. Verstappen, H.Th. 1983. Applied geomorphology. ITC, Enschede.

Using object-based geomorphometry for hydro-geomorphological analysis in a Mediterranean research catchment

NASA Astrophysics Data System (ADS)

Guida, Domenico; Cuomo, Albina; Palmieri, Vincenzo

2016-08-01

The aim of the paper is to apply an object-based geomorphometric procedure to define the runoff contribution areas and support a hydro-geomorphological analysis of a 3 km2 Mediterranean research catchment (southern Italy). Daily and sub-hourly discharge and electrical conductivity data were collected and recorded during a 3-year monitoring activity. Hydro-chemograph analyses carried out on these data revealed a strong seasonal hydrological response in the catchment that differed from the stormflow events that occur in the wet periods and in dry periods. This analysis enabled us to define the hydro-chemograph signatures related to increasing flood magnitude, which progressively involves various runoff components (baseflow, subsurface flow and surficial flow) and an increasing contributing area to discharge. Field surveys and water table/discharge measurements carried out during a selected storm event enabled us to identify and map specific runoff source areas with homogeneous geomorphological units previously defined as hydro-geomorphotypes (spring points, diffuse seepage along the main channel, seepage along the riparian corridors, diffuse outflow from hillslope taluses and concentrate sapping from colluvial hollows). Following the procedures previously proposed and used by authors for object-based geomorphological mapping, a hydro-geomorphologically oriented segmentation and classification was performed with the eCognition (Trimble, Inc.) package. The best agreement with the expert-based geomorphological mapping was obtained with weighted plan curvature at different-sized windows. By combining the hydro-chemical analysis and object-based hydro-geomorphotype map, the variability of the contribution areas was graphically modeled for the selected event, which occurred during the wet season, by using the log values of flow accumulation that better fit the contribution areas. The results allow us to identify the runoff component on hydro-chemographs for each time step and calculate a specific discharge contribution from each hydro-geomorphotype. This kind of approach could be useful when applied to similar, rainfall-dominated, forested and no-karst catchments in the Mediterranean eco-region.

UAV-based detection and spatial analyses of periglacial landforms on Demay Point (King George Island, South Shetland Islands, Antarctica)

NASA Astrophysics Data System (ADS)

Dąbski, Maciej; Zmarz, Anna; Pabjanek, Piotr; Korczak-Abshire, Małgorzata; Karsznia, Izabela; Chwedorzewska, Katarzyna J.

2017-08-01

High-resolution aerial images allow detailed analyses of periglacial landforms, which is of particular importance in light of climate change and resulting changes in active layer thickness. The aim of this study is to show possibilities of using UAV-based photography to perform spatial analysis of periglacial landforms on the Demay Point peninsula, King George Island, and hence to supplement previous geomorphological studies of the South Shetland Islands. Photogrammetric flights were performed using a PW-ZOOM fixed-winged unmanned aircraft vehicle. Digital elevation models (DEM) and maps of slope and contour lines were prepared in ESRI ArcGIS 10.3 with the Spatial Analyst extension, and three-dimensional visualizations in ESRI ArcScene 10.3 software. Careful interpretation of orthophoto and DEM, allowed us to vectorize polygons of landforms, such as (i) solifluction landforms (solifluction sheets, tongues, and lobes); (ii) scarps, taluses, and a protalus rampart; (iii) patterned ground (hummocks, sorted circles, stripes, nets and labyrinths, and nonsorted nets and stripes); (iv) coastal landforms (cliffs and beaches); (v) landslides and mud flows; and (vi) stone fields and bedrock outcrops. We conclude that geomorphological studies based on commonly accessible aerial and satellite images can underestimate the spatial extent of periglacial landforms and result in incomplete inventories. The PW-ZOOM UAV is well suited to gather detailed geomorphological data and can be used in spatial analysis of periglacial landforms in the Western Antarctic Peninsula region.

Ultra-Fine Scale Spatially-Integrated Mapping of Habitat and Occupancy Using Structure-From-Motion

PubMed Central

McDowall, Philip; Lynch, Heather J.

2017-01-01

Organisms respond to and often simultaneously modify their environment. While these interactions are apparent at the landscape extent, the driving mechanisms often occur at very fine spatial scales. Structure-from-Motion (SfM), a computer vision technique, allows the simultaneous mapping of organisms and fine scale habitat, and will greatly improve our understanding of habitat suitability, ecophysiology, and the bi-directional relationship between geomorphology and habitat use. SfM can be used to create high-resolution (centimeter-scale) three-dimensional (3D) habitat models at low cost. These models can capture the abiotic conditions formed by terrain and simultaneously record the position of individual organisms within that terrain. While coloniality is common in seabird species, we have a poor understanding of the extent to which dense breeding aggregations are driven by fine-scale active aggregation or limited suitable habitat. We demonstrate the use of SfM for fine-scale habitat suitability by reconstructing the locations of nests in a gentoo penguin colony and fitting models that explicitly account for conspecific attraction. The resulting digital elevation models (DEMs) are used as covariates in an inhomogeneous hybrid point process model. We find that gentoo penguin nest site selection is a function of the topography of the landscape, but that nests are far more aggregated than would be expected based on terrain alone, suggesting a strong role of behavioral aggregation in driving coloniality in this species. This integrated mapping of organisms and fine scale habitat will greatly improve our understanding of fine-scale habitat suitability, ecophysiology, and the complex bi-directional relationship between geomorphology and habitat use. PMID:28076351

A multi-characteristic based algorithm for classifying vegetation in a plateau area: Qinghai Lake watershed, northwestern China

NASA Astrophysics Data System (ADS)

Ma, Weiwei; Gong, Cailan; Hu, Yong; Li, Long; Meng, Peng

2015-10-01

Remote sensing technology has been broadly recognized for its convenience and efficiency in mapping vegetation, particularly in high-altitude and inaccessible areas where there are lack of in-situ observations. In this study, Landsat Thematic Mapper (TM) images and Chinese environmental mitigation satellite CCD sensor (HJ-1 CCD) images, both of which are at 30m spatial resolution were employed for identifying and monitoring of vegetation types in a area of Western China——Qinghai Lake Watershed(QHLW). A decision classification tree (DCT) algorithm using multi-characteristic including seasonal TM/HJ-1 CCD time series data combined with digital elevation models (DEMs) dataset, and a supervised maximum likelihood classification (MLC) algorithm with single-data TM image were applied vegetation classification. Accuracy of the two algorithms was assessed using field observation data. Based on produced vegetation classification maps, it was found that the DCT using multi-season data and geomorphologic parameters was superior to the MLC algorithm using single-data image, improving the overall accuracy by 11.86% at second class level and significantly reducing the "salt and pepper" noise. The DCT algorithm applied to TM /HJ-1 CCD time series data geomorphologic parameters appeared as a valuable and reliable tool for monitoring vegetation at first class level (5 vegetation classes) and second class level(8 vegetation subclasses). The DCT algorithm using multi-characteristic might provide a theoretical basis and general approach to automatic extraction of vegetation types from remote sensing imagery over plateau areas.

Geologic characteristics of benthic habitats in Glacier Bay, southeast Alaska

USGS Publications Warehouse

Harney, Jodi N.; Cochrane, Guy R.; Etherington, Lisa L.; Dartnell, Pete; Golden, Nadine E.; Chezar, Hank

2006-01-01

In April 2004, more than 40 hours of georeferenced submarine digital video was collected in water depths of 15-370 m in Glacier Bay to (1) ground-truth existing geophysical data (bathymetry and acoustic reflectance), (2) examine and record geologic characteristics of the sea floor, and (3) investigate the relation between substrate types and benthic communities, and (4) construct predictive maps of seafloor geomorphology and habitat distribution. Common substrates observed include rock, boulders, cobbles, rippled sand, bioturbated mud, and extensive beds of living horse mussels and scallops. Four principal sea-floor geomorphic types are distinguished by using video observations. Their distribution in lower and central Glacier Bay is predicted using a supervised, hierarchical decision-tree statistical classification of geophysical data.

Geomorphologic flood-hazard assessment of alluvial fans and piedmonts

USGS Publications Warehouse

Field, J.J.; Pearthree, P.A.

1997-01-01

Geomorphologic studies are an excellent means of flood-hazard assessment on alluvial fans and piedmonts in the southwestern United States. Inactive, flood-free, alluvial fans display well developed soils, desert pavement, rock varnish, and tributary drainage networks. These areas are easily distinguished from flood-prone active alluvial fans on aerial photographs and in the field. The distribution of flood-prone areas associated with alluvial fans is strongly controlled by fanhead trenches dissecting the surface. Where fanhead trenches are permanent features cut in response to long-term conditions such as tectonic quiescence, flood-prone surfaces are situated down-slope from the mountain front and their positions are stable for thousands of years. Since the length and permanency of fanhead trenches can vary greatly between adjacent drainages, it is not appropriate to use regional generalizations to evaluate the distribution and stability of flood-hazard zones. Site-specific geomorphologic studies must be carried out if piedmont areas with a high risk of flooding are to be correctly identified and losses due to alluvial-fan flooding minimized. To meet the growing demand for trained professionals to complete geomorphologic maps of desert piedmonts, undergraduate and graduate geomorphology courses should adopt an instructional unit on alluvial-fan flood hazards that includes: 1) a review of geomorphologic characteristics that vary with surface age; 2) a basic mapping exercise; and 3) a discussion of the causes of fanhead trenching.

Quantifying uncertainty of measuring gully morphological evolution with close-range digital photogrammetry

USDA-ARS?s Scientific Manuscript database

Measurement of geomorphic change may be of interest to researchers and practitioners in a variety of fields including geology, geomorphology, hydrology, engineering, and soil science. Landscapes are often represented by digital elevation models. Surface models generated of the same landscape over a ...

Near surface geophysics techniques and geomorphological approach to reconstruct the hazard cave map in historical and urban areas

NASA Astrophysics Data System (ADS)

Lazzari, M.; Loperte, A.; Perrone, A.

2010-03-01

This work, carried out with an integrated methodological approach, focuses on the use of near surface geophysics techniques, such as ground penetrating radar and electrical resistivity tomography (ERT), and geomorphological analysis, in order to reconstruct the cave distribution and geometry in a urban context and, in particular, in historical centres. The interaction during recent centuries between human activity (caves excavation, birth and growth of an urban area) and the characters of the natural environment were the reasons of a progressive increase in hazard and vulnerability levels of several sites. The reconstruction of a detailed cave map distribution is the first step to define the anthropic and geomorphological hazard in urban areas, fundamental basis for planning and assessing the risk.

Geomorphological Mapping on the Southern Hemisphere of Comet 67P/Churyumov-Gerasimenko

NASA Astrophysics Data System (ADS)

Lee, Jui-Chi; Massironi, Matteo; Giacomini, Lorenza; Ip, Wing-Huen; El-Maarry, Mohamed R.

2016-04-01

Since its rendezvous with comet 67P/Churyumov-Gerasimenko on the sixth of August, 2014, the Rosetta spacecraft has carried out close-up observations of the nucleus and coma of this Jupiter family comet. The OSIRIS, the Scientific Imaging Camera System onboard the Rosetta spacecraft, which consists of a narrow-angle and wide-angle camera (NAC and WAC), has made detailed investigations of the physical properties and surface morphology of the comet. From May 2015, the southern hemisphere of the comet became visible and the adaptical resolution was high enough for us to do a detailed analysis of the surface. Previous work shows that the fine particle deposits are the most extensive geomorphological unit in the northern hemisphere. On the contrary, southern hemisphere is dominated by rocky-like stratified terrain. The southern hemisphere of the nucleus surface reveals quite different morphologies from the northern hemisphere. This could be linked to the different insolation condition between northern and southern hemisphere. As a result, surface geological processes could operate with a diverse intensity on the different sides of the comet nucleus. In this work, we provide the geomorphological maps of the southern hemisphere with linear features and geological units identified. The geomorphological maps described in this study allow us to understand the processes and the origin of the comet.

Mapping soil erosion risk in Serra de Grândola (Portugal)

NASA Astrophysics Data System (ADS)

Neto Paixão, H. M.; Granja Martins, F. M.; Zavala, L. M.; Jordán, A.; Bellinfante, N.

2012-04-01

Geomorphological processes can pose environmental risks to people and economical activities. Information and a better knowledge of the genesis of these processes is important for environmental planning, since it allows to model, quantify and classify risks, what can mitigate the threats. The objective of this research is to assess the soil erosion risk in Serra de Grândola, which is a north-south oriented mountain ridge with an altitude of 383 m, located in southwest of Alentejo (southern Portugal). The study area is 675 km2, including the councils of Grândola, Santiago do Cacém and Sines. The process for mapping of erosive status was based on the guidelines for measuring and mapping the processes of erosion of coastal areas of the Mediterranean proposed by PAP/RAC (1997), developed and later modified by other authors in different areas. This method is based on the application of a geographic information system that integrates different types of spatial information inserted into a digital terrain model and in their derivative models. Erosive status are classified using information from soil erodibility, slope, land use and vegetation cover. The rainfall erosivity map was obtained using the modified Fournier index, calculated from the mean monthly rainfall, as recorded in 30 meteorological stations with influence in the study area. Finally, the soil erosion risk map was designed by ovelaying the erosive status map and the rainfall erosivity map.

Early Writing in the Research Mode via Digital Modeling of Rivers.

ERIC Educational Resources Information Center

Snow, Robin Scott

1991-01-01

Author describes an individual research project involving digital modeling of graded river profiles as part of a sophomore-level geomorphology class. The three-week project gives students the opportunity to choose research topics, design experiments to test ideas, interpret results, and write a research report. (PR)

Geomorphology of coal seam fires

NASA Astrophysics Data System (ADS)

Kuenzer, Claudia; Stracher, Glenn B.

2012-02-01

Coal fires occur in underground natural coal seams, in exposed surface seams, and in coal storage or waste piles. The fires ignite through spontaneous combustion or natural or anthropogenic causes. They are reported from China, India, USA, South Africa, Australia, and Russia, as well as many other countries. Coal fires lead to loss of a valuable resource (coal), the emission of greenhouse-relevant and toxic gases, and vegetation deterioration. A dangerous aspect of the fires is the threat to local mines, industries, and settlements through the volume loss underground. Surface collapse in coal fire areas is common. Thus, coal fires are significantly affecting the evolution of the landscape. Based on more than a decade of experience with in situ mapping of coal fire areas worldwide, a general classification system for coal fires is presented. Furthermore, coal seam fire geomorphology is explained in detail. The major landforms associated with, and induced by, these fires are presented. The landforms include manifestations resulting from bedrock surface fracturing, such as fissures, cracks, funnels, vents, and sponges. Further manifestations resulting from surface bedrock subsidence include sinkholes, trenches, depressions, partial surface subsidence, large surface subsidence, and slides. Additional geomorphologic coal fire manifestations include exposed ash layers, pyrometamorphic rocks, and fumarolic minerals. The origin, evolution, and possible future development of these features are explained, and examples from in situ surveys, as well as from high-resolution satellite data analyses, are presented. The geomorphology of coal fires has not been presented in a systematic manner. Knowledge of coal fire geomorphology enables the detection of underground coal fires based on distinct surface manifestations. Furthermore, it allows judgments about the safety of coal fire-affected terrain. Additionally, geomorphologic features are indicators of the burning stage of fires. Finally, coal fire geomorphology helps to explain landscape features whose occurrence would otherwise not be understood. Although coal fire-induced thermal anomalies and gas release are also indications of coal fire activity, as addressed by many investigators, no assessment is complete without sound geomorphologic mapping of the fire-induced geomorphologic features.

A Transient Landscape: Geospatial Analysis and Numerical Modeling of Coastal Geomorphology in the Outer Banks, North Carolina

NASA Astrophysics Data System (ADS)

Hardin, Eric Jon

Coastal landscapes can be relentlessly dynamic---owing to wave energy, tidal cycles, extreme weather events, and perpetual coastal winds. In these settings, the ever-changing landscape can threaten assets and infrastructure, necessitating costly measures to mitigate associated risks and to repair or maintain the changing landscape. Mapping and monitoring of terrain change, identification of areas susceptible to dramatic change, and understanding the processes that drive landscape change are critical for the development of responsible coastal management strategies and policies. Over the past two decades, LiDAR mapping has been conducted along the U.S. east coast (including the Outer Banks, North Carolina) on a near annual basis---generating a rich time series of topographic data with unprecedented accuracy, resolution, and extent. This time series has captured the response of the landscape to episodic storms, daily forcing of wind and waves, and anthropogenic activities. This work presents raster-based geospatial techniques developed to gain new insights into coastal geomorphology from the time series of available LiDAR. Per-cell statistical techniques derive information that is typically not obtained through the techniques traditionally employed by coastal scientists and engineers. Application of these techniques to study sites along the Outer Banks, NC, revealed substantial spatial and temporal variations in terrain change. Additionally, they identify the foredunes as being the most geomorphologically dynamic coastal features. In addition to per-cell statistical analysis, an approach is presented for the extraction of the dune ridge and dune toe (two features that are essential to standard vulnerability assessment). The approach employs a novel application of least cost path analysis and a physics-based model of an elastic sheet. The spatially distributed nature of the approach achieves a high level of automation and repeatability that semi-automated methods and manual digitization lack. Furthermore, the approach can be fully implemented with standard Geographic Information System (GIS) functionality, resulting in efficiency and ease of implementation. With this approach, a raster-based implementation of the U.S. Geological Survey (USGS) storm impact scale (designed to assess storm vulnerability of barrier islands) was developed. Vulnerability of 4km of the Outer Banks to Hurricane Isabel (2003) was assessed. The demonstrated approach produced vulnerability mapping at the high resolution of the input Digital Elevation Model (DEM)---providing results at the scale needed for local management, in contrast to the USGS approach, which is designed for continental scale vulnerability assessment. However, geospatial techniques cannot fully explain the observed geomorphology. Therefore, we present the Smoothed Particle Hydrodynamics (SPH) implementation of the Sauermann model for wind-driven sand transport. The SPH implementation enables the full nonlinearity of the model to be applied to complex scenarios that are typical of coastal landscapes. Through application of the SPH model and Computational Fluid Dynamics (CFD) modeling of the windborne surface shear stress (which drives sand transport), we present the sediment flux at two study sites along the Outer Banks. Scenarios were tested that involved steady-state surface shear stress as well as scenarios with intermittent variations in the surface shear stress. Results showed that intermittency in the surface shear stress has the potential to greatly influence the resulting flux. However, the degree to which intermittency does alter the flux is highly dependent on wind characteristics and wind direction relative to the orientation of salient topographic features.

A review of the activities of the IAG working group on geomorphosites over the last ten years

NASA Astrophysics Data System (ADS)

Reynard, Emmanuel; Coratza, Paola

2013-04-01

During the last two decades a renewed interest emerged in the scientific community for geoheritage, geoconservation and geotourism research. This was the reason for the International Association of Geomorphologists (IAG) for creating a specific working group on geomorphosites in 2001, with the aim to improve knowledge and scientific research on the definition, assessment, cartography, promotion and conservation of geomorphological heritage. The working group is chaired by the two authors, experiences were shared during several workshops and international conferences, and results were collected in several special publications (http://www.geomorph.org/wg/wggs.html). Several intensive courses for Master and PhD students were also organized and a book was published, dedicated particularly to Master and PhD students working on geomorphosite issues (Reynard et al., 2009). This contribution proposes a review of the working group activities since 2001 that focused on four main domains: (1) Definition and conceptualization. Geomorphosites are a type of geosite that is portions of the geosphere that present a particular importance for the comprehension of the Earth's history. Geomorphosites have to be considered as the result of human valuation. Conceptualization related to the value of geomorphosites is still in course. Nevertheless, three groups of values can be demonstrated: the scientific value (that is the interest of sites for Earth history and for the history and epistemology of geomorphology), several additional values (aesthetic, ecological, and cultural in a broad sense), and use and management values, that can be divided in three groups (educational value, economic value, including the tourist value, and protection). The scientific and additional value can be considered as intrinsic values, whereas the management and use value are to be related to extrinsic or societal values. (2) Assessment. Several methods, based on the measurement of specific features of geomorphosites, were applied. A problem found in practically all of them is the subjectivity of assessment and, consequently, the difficulty for one operator to replicate results obtained by another. The original objective of the WG was, after four years, to publish guidelines to assess geomorphosites. Nevertheless, the works have shown that the development of general guidelines to be used by all the countries was quite impossible, because the choice of assessment methods depends on the objectives and the context of the research. For this reason, the project of guidelines was abandoned and several of the methods available were developed. These methods have their specificities and are based on several assessment criteria. Nevertheless, it is possible to recognize common and recurrent assessment criteria, like rarity, representativeness and integrity, and others, for example ecological value, palaeogeographic importance, educational value etc., that are dependent on the context of the assessment and on the aims of the research. (3) Mapping. Designing maps is not a simple procedure and in the codification phase (implementation of the map) several points should be considered, in particular, when mapping geomorphosites efforts should be made to identify and use symbols corresponding to semiotic criteria (communicative immediacy, graphic originality and flexibility). Although it is not possible to set up a standardized methodology valid for all purposes, the WG proposed guiding principles for geomorphosite mapping. (4) Education and dissemination. The issue of interpretation of geomorphological heritage, in particular the sensitive question of the adequacy of geoproducts with the public needs and previous knowledge, was also addressed by the WG, and several scholars proposed methods for interpreting geomorphology in a geotourist context. Several questions have not been solved until now and should be addressed in the future: (1) The scale issue in geomorphosite studies is not clearly addressed, even if it impacts on several domains such as the assessment and cartography of geomorphological heritage; (2) Relationships between geoheritage assessment and geodiversity assessment may also be explored in the future, especially in terms of geoconservation; (3) Guidelines such as those proposed for the mapping issues and for the elaboration of geotourist products are particularly useful and a book of good practices in the fields of geomorphological heritage assessment, cartography and interpretation should be encouraged; (4) Finally, the integration of geomorphosite studies with other scientific domains is needed, in particular with educational and social sciences in the field of public characterization, with computer sciences in the field of knowledge dissemination using digital technologies, with political and law sciences in the field of geoconservation, and with process geomorphology in the management of geomorphosites in particularly dynamic environments. Reference Reynard E., Coratza P., Regolini-Bissig G. (2009) (Eds.). Geomorphosites. München, Pfeil Verlag.

Urban geomorphological heritage - A new field of research

NASA Astrophysics Data System (ADS)

Reynard, Emmanuel; Pica, Alessia; Coratza, Paola

2017-04-01

Urbanization is one of the major challenges that the world faces. In 2015, 54% of the world population was living in urban areas and in some countries this percentage is close to 100% (Singapore 100%; Qatar 99%; Belgium 98%). In several parts of the world annual urbanization rates exceed 5% (e.g. Oman 8.54%; Rwanda 6.43%; Burkina Faso 5.87%), which means that urban sprawl is a widespread phenomenon. Urbanization and correlated infrastructure building highly impact and sometimes completely destroy natural landforms. Geomorphological heritage research has traditionally focused on rural or natural regions, in particular protected areas (nature parks, geoparks). We consider that urban areas, which have been poorly investigated until now, are particularly interesting in a geomorphological heritage point of view for almost three reasons: (i) The geomorphological context (site) of some cities is part of their "image" and their fame (e.g. the sugarloaf of Rio de Janeiro); (ii) Urban sprawl often interacts with landforms, which addresses the challenge of geoheritage protection in fast urbanizing areas; (iii) Cities are often tourist destinations, which creates a potential for a geotourist promotion of their geomorphological heritage. This study addresses the main challenges research on geomorphological heritage is facing in urban contexts: (i) the complex interrelationships between natural landforms and urban forms; (ii) the partial or total invisibility of landforms and sediments that are covered or destroyed by urban infrastructures; (iii) man-made landforms as part of urban geomorphological heritage; (iv) the suitability of some landforms (valleys, gullies, mounts) for specific urban uses; (v) the geomorphic constraints of landforms on urban development; and (vi) the importance of some landforms for the urban landscape and the image of the cities. To address these challenges a methodological framework is proposed, which combines: (i) the geomorphological analysis of the urban landscape through geomorphological mapping (with use of a specific legend for man-made landforms) and geohistorical analysis of landscape evolution (historical maps processing); (ii) the selection, characterization and assessment of urban geomorphosites; (iii) proposals for the conservation and promotion (geotourism) of the urban geomorphological heritage.

The use of a GIS Red-Amber-Green (RAG) system to define search priorities for burials

NASA Astrophysics Data System (ADS)

Somma, Roberta; Silvestro, Massimiliano; Cascio, Maria; Dawson, Lorna; Donnelly, Laurance; Harrison, Mark; McKinley, Jennifer; Ruffell, Alastair

2016-04-01

The aim of this research is to promote among the Italian police, magistrates, and geologists, the applications of a Geographical Information System (GIS)-based RAG system for use in ground searches for burials. To date the RAG system has not been used and documented in Italy and would potentially be useful for searches related to clandestine burial sites. This technique, was originally documented by the British Army in the 1st World War. The RAG method is based on the construction of theme maps. RAG maps can facilitate the deployment of appropriate search assets (such as geophysics, probe or search dogs) and therefore applied to ground searches for the potential location of homicide graves or other buried objects (including weapons, explosives, etc.). RAG maps also may assist in the management of resources such as the deployment of search personnel, search teams and dogs. A GIS RAG (Red-Amber-Green) system related to a search for a homicide grave was applied to a test site in Italy, simulating the concealment of a victim in the area of Alì. This is an area of hill in Sicily, characterized by Palaeozoic phyllites. It was assumed during this test that information was provided by an observer who saw a suspect carrying tools on his land during daylight hours. A desktop study of the rural area was first implemented. Data was collated from previous geological, geomorphological, hydrogeological, geophysical and land use surveys. All these data were stored and independently analysed in a GIS using ArcGIS software. For the development of the GIS-based RAG map a digital elevation model (DEM) including a digital surface model (DTS) and digital terrain model (DTM) types were used. These were integrated with data from soil surveys to provide a preliminary assessment of "diggability" - including the possible thickness of loose superficial deposits and soils. Data were stored in different layers within the GIS. These included the delineation of the search area with consideration of access/exit points, diggability (easy: red, difficult: green), ground slope (<27°: red, >27°: green), vegetation type (easy access: red, difficult access: green), geomorphology (stable area: red, unstable area: green), anthropogenic structures (not present: red, present: green), visibility of the site from a potential eyewitnesses perspective (not visible: red, visible: green). Overlaying these layers, using the ArcGIS tools, enabled the RAG map to be composed with red showing the high priority search areas, amber the intermediate priority search areas and green the low priority search areas. The GIS-based RAG map of the simulated test-site allowed the original extent of the search area of 39.315m2, to be significantly reduced to 7.45% (2.930m2: extension red area) by desktop study and to 2.93% (1.152m2) with a further reconnaissance site visit. During subsequent field training conducted by forensic geology students at Messina University, the grave was found after 2 hours of searching, both using the RAG map and a soil probe and observing topographic disturbances. A subsidence of some centimeters and an anomalous growth of vegetation was found on the superficial surface of the grave (75cm deep).

Investigating talus slope geomorphology as impacted by permafrost thaw (Valais, Switzerland): stipulating a research framework

NASA Astrophysics Data System (ADS)

Hendrickx, Hanne; Delaloye, Reynald; Nyssen, Jan; Frankl, Amaury

2017-04-01

Climate change is altering temperature regimes and precipitation patterns worldwide. In the European Alps, atmospheric temperatures have risen twice as fast as the global average since 1900, while precipitation regimes are changing as well. Snow cover duration and extent has significantly decreased in the Swiss Alps, mainly due to earlier spring melt and rise in winter temperatures. Moreover, future projections predict a continuation of these trends. Spatial distribution and thermal properties of permafrost are highly influenced by ground surface conditions (snow and vegetation) and air temperature. Climate induced permafrost degradation is, therefore, expected. While alpine permafrost research has mainly focused on rock glaciers, less attention has been given to talus slopes. The latter are subjected to different kinds of slope processes such as debris flows, solifluction, permafrost creep, avalanches and rock fall. These processes are especially effective under a changing periglacial climate. Therefore, it is important to study permafrost distribution in these talus slopes, since it is believed to have large influence on slope stability. In this study, permafrost distribution will be mapped on several talus slope segments (10 - 40 ha) using geomorphological evidence, temperature data and measuring electrical resistivity tomography (ERT) profiles in addition to already existing data. The current dynamics of the study area will be studied by constructing detailed 3D models, using ground based and aerial photography (Unmanned Aerial Vehicles, UAV) and the Structure-from-Motion method (SfM). The resulting Digital Elevation Models (DEM) will be used to quantify and understand the current geomorphological processes acting on these talus slopes. Historical aerial and terrestrial photographs will be used to give an idea about the magnitude and frequency of past geomorphic processes (e.g. debris flows). Historical and current dynamics can then be compared and contrasted with permafrost occurrence. By doing so, this study will answer following question: "To which extent will climate-induced permafrost degradation impact geomorphological processes on talus slopes?".

Electronic atlas of the Russian Arctic coastal zone: natural conditions and technogenic risk

NASA Astrophysics Data System (ADS)

Drozdov, D. S.; Rivkin, F. M.; Rachold, V.

2004-12-01

The Arctic coast is characterized by a diversity of geological-geomorphological structures and geocryological conditions, which are expected to respond differently to changes in the natural environment and in anthropogenic impacts. At present, oil fields are prospected and developed and permanent and temporary ports are constructed in the Arctic regions of Russia. Thus, profound understanding of the processes involved and measures of nature conservation for the coastal zone of the Arctic Seas are required. One of the main field of Arctic coastal investigations and database formation of coastal conditions is the mapping of the coasts. This poster presents a set of digital maps including geology, quaternary sediments, landscapes, engineering-geology, vegetation, geocryology and a series of regional sources, which have been selected to characterize the Russian Arctic coast. The area covered in this work includes the 200-km-wide band along the entire Russian Arctic coast from the Norwegian boundary in the west to the Bering Strait in the east. Methods included the collection of the majority of available hard copies of cartographic material and their digital formats and the transformation of these sources into a uniform digital graphic format. The atlas consists of environmental maps and maps of engineering-geological zoning. The set of environmental maps includes geology, quaternary sediments, landscapes and vegetation of the Russian Arctic coast at a scale of 1:4000000. The set of engineering-geocryological maps includes a map of engineering-geocryological zoning of the Russian Arctic coast, a map of the intensity of destructive coastal process and a map of industrial impact risk assessment ( 1:8000000 scale). Detailed mapping has been performed for key sites (at a scale of 1:100000) in order to enable more precise estimates of the intensity of destructive coastal process and industrial impact. The engineering-geocryological map of the Russian Arctic coast was compiled based on the analysis of geotechnical and geocryological conditions in the areas adjacent to the coastal band. Industrial impact assessment has been estimated differently for each engineering-geocryological region distinguished on the coast, considering technological features of construction and engineering facilities: aerial construction, highways and airdromes, underground (with positive and negative pipe temperatures) and surface pipelines and quarries. The atlas is being used as a base for the circum-Arctic segmentation of the coastline and the analyses of coastal dynamics within the Arctic Coastal Dynamics (ACD) Project. The work has been supported by INTAS (project number 01-2332).

The topographic grain concept in DEM-based geomorphometric mapping

NASA Astrophysics Data System (ADS)

Józsa, Edina

2016-04-01

A common drawback of geomorphological analyses based on digital elevation datasets is the definition of search window size for the derivation of morphometric variables. The fixed-size neighbourhood determines the scale of the analysis and mapping, which can lead to the generalization of smaller surface details or the elimination of larger landform elements. The methods of DEM-based geomorphometric mapping are constantly developing into the direction of multi-scale landform delineation, but the optimal threshold for search window size is still a limiting factor. A possible way to determine the suitable value for the parameter is to consider the topographic grain principle (Wood, W. F. - Snell, J. B. 1960, Pike, R. J. et al. 1989). The calculation is implemented as a bash shell script for GRASS GIS to determine the optimal threshold for the r.geomorphon module. The approach relies on the potential of the topographic grain to detect the characteristic local ridgeline-to-channel spacing. By calculating the relative relief values with nested neighbourhood matrices it is possible to define a break-point where the increase rate of local relief encountered by the sample is significantly reducing. The geomorphons approach (Jasiewicz, J. - Stepinski, T. F. 2013) is a cell-based DEM classification method for the identification of landform elements at a broad range of scales by using line-of-sight technique. The landforms larger than the maximum lookup distance are broken down to smaller elements therefore the threshold needs to be set for a relatively large value. On the contrary, the computational requirements and the size of the study sites determine the upper limit for the value. Therefore the aim was to create a tool that would help to determine the optimal parameter for r.geomorphon tool. As a result it would be possible to produce more objective and consistent maps with achieving the full efficiency of this mapping technique. For the thorough analysis on the applicability of the proposed methodology a test site covering hilly and low mountainous regions in Southern Transdanubia, Hungary was chosen. As elevation dataset the freely available SRTM DSM with 1 arc-second resolution was used, after implementing necessary error correction. Based on the delineated landform elements and morphometric variables the physiographic characteristics of the landscape could be analysed and compared with the existing expert-based map of microregions. References: Wood, W. F. and J. B. Snell (1960). A quantitative system for classifying landforms. - Technical Report EP-124. U.S. Army Quartermaster Research and Engineering Center, Natick, 20 pp. Pike, R. J., et al. (1989). Topographic grain automated from digital elevation models. - Proceedings, Auto-Carto 9, ASPRS/ACSM Baltimore MD, 2-7 April 1989. Jasiewicz, J. and T. F. Stepinski (2013). Geomorphons - a pattern recognition approach to classification and mapping of landforms. - Geomorphology 182(0): 147-156.

An approach for quantifying geomorphological impacts for EIA of transportation infrastructures: a case study in northern Spain

NASA Astrophysics Data System (ADS)

Bonachea, Jaime; Bruschi, Viola Maria; Remondo, Juan; González-Díez, Alberto; Salas, Luis; Bertens, Jurjen; Cendrero, Antonio; Otero, César; Giusti, Cecilia; Fabbri, Andrea; González-Lastra, José Ramón; Aramburu, José María

2005-03-01

A methodological proposal for the assessment of impacts due to linear infrastructures such as motorways, railways, etc. is presented. The approach proposed includes a series of specific issues to be addressed for each geomorphological feature analysed—both 'static' and 'dynamic'—as well as a series of steps to be followed in the process. Geomorphic characteristics potentially affected were initially identified on the basis of a conceptual activities/impacts model that helps to single out geomorphic impacts related to environmental concerns for the area. The following issues were addressed for each individual impact: nature of potential effects; indicators that can be used to measure impacts; criteria of 'geomorphologic performance'; procedure for measurement/prediction of changes; translation of geomorphologic impacts into significant terms from the viewpoint of human concerns; possible mitigation and/or compensation measures. The procedure has been applied to a case study corresponding to a new motorway in the Basque Country, northern Spain. Geomorphological impacts considered in this analysis included: (1) consumable resources; (2) sites of geomorphological interest; (3) land units with high potential for use, high productivity or value for conservation; (4) visual landscape; (5) slope instability processes. The procedure has been designed for implementation in a Geographic Information System (GIS) environment. Details are given on the application of the method to each individual impact analysed and results are presented in both numerical and map form. Impacts assessed were initially expressed by means of heterogeneous magnitudes, depending on the geomorphological feature considered. Those geomorphological impacts were then translated into significant terms and homogeneous magnitudes. Integration was carried out on the basis of impact values thus obtained. Final integrated results were also expressed in numerical and map form. The method proposed enables comparison of alternatives as well as 'prediction' and assessment of impacts in terms directly related to geomorphic characteristics. It also facilitates the expression of those impacts in terms that allow integration with other types of environmental impacts.

Forensic geomorphology

NASA Astrophysics Data System (ADS)

Ruffell, Alastair; McKinley, Jennifer

2014-02-01

Geomorphology plays a critical role in two areas of geoforensics: searching the land for surface or buried objects and sampling scenes of crime and control locations as evidence. Associated geoscience disciplines have substantial bodies of work dedicated to their relevance in forensic investigations, yet geomorphology (specifically landforms, their mapping and evolution, soils and relationship to geology and biogeography) have not had similar public exposure. This is strange considering how fundamental to legal enquiries the location of a crime and its evolution are, as this article will demonstrate. This work aims to redress the balance by showing how geomorphology featured in one of the earliest works on forensic science methods, and has continued to play a role in the sociology, archaeology, criminalistics and geoforensics of crime. Traditional landscape interpretation from aerial photography is used to demonstrate how a geomorphological approach saved police time in the search for a clandestine grave. The application geomorphology has in military/humanitarian geography and environmental/engineering forensics is briefly discussed as these are also regularly reviewed in courts of law.

Comparison of UAV and TLS DTMs for acquisition of geological, geomorphological information for Doren landslide, Vorarlberg Austria

NASA Astrophysics Data System (ADS)

Koma, Zsófia; Székely, Balázs; Dorninger, Peter; Rasztovits, Sascha; Roncat, Andreas; Zámolyi, András; Krawczyk, Dominik; Pfeifer, Norbert

2014-05-01

Aerial imagery derivatives collected by the Unmanned Aerial Vehicle (UAV) technology can be used as input for generation of high resolution digital terrain model (DTM) data along with the Terrestrial Laser Scanning (TLS) method. Both types of datasets are suitable for detailed geological and geomorphometric analysis, because the data provide micro-topographical and structural geological information. Our study focuses on the comparison of the possibilities of the extracted geological information, which is available from high resolution DTMs. This research attempts to find an answer which technology is more effective for geological and geomorphological analysis. The measurements were taken at the Doren landslide (Vorarlberg, Austria), a complex rotational land slide situated in the Alpine molasse foreland. Several formations (Kojen Formation, Würmian glacial moraine sediments, Weissach Formation) were tectonized there in the course of the alpine orogeny (Oberhauser et al, 2007). The typical fault direction is WSW-ENE. The UAV measurements that were carried out simultaneously with the TLS campaign focused on the landslide scarp. The original image resolution was 4 mm/pixel. Image matching was implemented in pyramid level 2 and the achieved resolution of the DTM was 0.05 meter. The TLS dataset includes 18 scan positions and more than 300 million points for the whole landslide area. The achieved DTM has 0.2 meter resolution. The steps of the geological and geomorphological analysis were: (1) visual interpretation based on field work and geological maps, (2) quantitative DTM analysis. In the quantitative analysis input data provided by the different kinds of DTMs were used for further parameter calculations (e.g. slope, aspect, sigmaZ). In the next step an automatic classification method was used for the detection of faults and classification of different parts of the landslide. The conclusion was that for geological visualization interpretation UAV datasets are better, because the high resolution texture information allows for the extraction of the digital geomorphology indicators. For quantitative analysis both datasets are informative, but the TLS DTM has an advantage of accessing additional information on faults beneath the vegetation cover. These studies were carried out partly in the framework of Hybrid 3D project financed by the Austrian Research Promotion Agency (FFG) and Von-Oben and 4D-IT; the contribution of ZsK was partly funded by Campus Hungary Internship TÁMOP-424B1; BSz contributed partly as an Alexander von Humboldt Research Fellow.

Digital modelling of landscape and soil in a mountainous region: A neuro-fuzzy approach

NASA Astrophysics Data System (ADS)

Viloria, Jesús A.; Viloria-Botello, Alvaro; Pineda, María Corina; Valera, Angel

2016-01-01

Research on genetic relationships between soil and landforms has largely improved soil mapping. Recent technological advances have created innovative methods for modelling the spatial soil variation from digital elevation models (DEMs) and remote sensors. This generates new opportunities for the application of geomorphology to soil mapping. This study applied a method based on artificial neural networks and fuzzy clustering to recognize digital classes of land surfaces in a mountainous area in north-central Venezuela. The spatial variation of the fuzzy memberships exposed the areas where each class predominates, while the class centres helped to recognize the topographic attributes and vegetation cover of each class. The obtained classes of terrain revealed the structure of the land surface, which showed regional differences in climate, vegetation, and topography and landscape stability. The land-surface classes were subdivided on the basis of the geological substratum to produce landscape classes that additionally considered the influence of soil parent material. These classes were used as a framework for soil sampling. A redundancy analysis confirmed that changes of landscape classes explained the variation in soil properties (p = 0.01), and a Kruskal-Wallis test showed significant differences (p = 0.01) in clay, hydraulic conductivity, soil organic carbon, base saturation, and exchangeable Ca and Mg between classes. Thus, the produced landscape classes correspond to three-dimensional bodies that differ in soil conditions. Some changes of land-surface classes coincide with abrupt boundaries in the landscape, such as ridges and thalwegs. However, as the model is continuous, it disclosed the remaining variation between those boundaries.

Deciphering groundwater potential zones in hard rock terrain using geospatial technology.

PubMed

Dar, Imran A; Sankar, K; Dar, Mithas A

2011-02-01

Remote sensing and geographical information system (GIS) has become one of the leading tools in the field of groundwater research, which helps in assessing, monitoring, and conserving groundwater resources. This paper mainly deals with the integrated approach of remote sensing and GIS to delineate groundwater potential zones in hard rock terrain. Digitized vector maps pertaining to chosen parameters, viz. geomorphology, geology, land use/land cover, lineament, relief, and drainage, were converted to raster data using 23 m×23 m grid cell size. Moreover, curvature of the study area was also considered while manipulating the spatial data. The raster maps of these parameters were assigned to their respective theme weight and class weights. The individual theme weight was multiplied by its respective class weight and then all the raster thematic layers were aggregated in a linear combination equation in Arc Map GIS Raster Calculator module. Moreover, the weighted layers were statistically modeled to get the areal extent of groundwater prospects with respect to each thematic layer. The final result depicts the favorable prospective zones in the study area and can be helpful in better planning and management of groundwater resources especially in hard rock terrains.

Geologic interpretation and multibeam bathymetry of the sea floor in southeastern Long Island Sound

USGS Publications Warehouse

Poppe, Lawrence J.; Ackerman, Seth D.; Doran, Elizabeth F.; Moser, Marc S.; Stewart, Helen F.; Forfinski, Nicholas A.; Gardner, Uther L.; Keene, Jennifer A.

2006-01-01

Digital terrain models (DTMs) produced from multibeam echosounder (MBES) bathymetric data provide valuable base maps for marine geological interpretations (e.g. Todd and others, 1999; Mosher and Thomson, 2002; ten Brink and others, 2004; Poppe and others, 2006a,b). These maps help define the geological variability of the sea floor (one of the primary controls of benthic habitat diversity); improve our understanding of the processes that control the distribution and transport of bottom sediments, the distribution of benthic habitats and associated infaunal community structures; and provide a detailed framework for future research, monitoring, and management activities. The bathymetric survey interpreted herein (National Oceanic and Atmospheric Administration (NOAA) survey H11255) covers roughly 95 km? of sea floor in southeastern Long Island Sound (fig. 1). This bathymetry has been examined in relation to seismic reflection data collected concurrently, as well as archived seismic profiles acquired as part of a long-standing geologic mapping partnership between the State of Connecticut and the U.S. Geological Survey (USGS). The objective of this work was to use these geophysical data sets to interpret geomorphological attributes of the sea floor in terms of the Quaternary geologic history and modern sedimentary processes within Long Island Sound.

Integrating geospatial and ground geophysical information as guidelines for groundwater potential zones in hard rock terrains of south India.

PubMed

Rashid, Mehnaz; Lone, Mahjoor Ahmad; Ahmed, Shakeel

2012-08-01

The increasing demand of water has brought tremendous pressure on groundwater resources in the regions were groundwater is prime source of water. The objective of this study was to explore groundwater potential zones in Maheshwaram watershed of Andhra Pradesh, India with semi-arid climatic condition and hard rock granitic terrain. GIS-based modelling was used to integrate remote sensing and geophysical data to delineate groundwater potential zones. In the present study, Indian Remote Sensing RESOURCESAT-1, Linear Imaging Self-Scanner (LISS-4) digital data, ASTER digital elevation model and vertical electrical sounding data along with other data sets were analysed to generate various thematic maps, viz., geomorphology, land use/land cover, geology, lineament density, soil, drainage density, slope, aquifer resistivity and aquifer thickness. Based on this integrated approach, the groundwater availability in the watershed was classified into four categories, viz. very good, good, moderate and poor. The results reveal that the modelling assessment method proposed in this study is an effective tool for deciphering groundwater potential zones for proper planning and management of groundwater resources in diverse hydrogeological terrains.

Improving fieldwork by using GIS for quantitative exploration, data management and digital mapping

NASA Astrophysics Data System (ADS)

Marra, Wouter; Alberti, Koko; van de Grint, Liesbeth; Karssenberg, Derek

2016-04-01

Fieldwork is an essential part of teaching geosciences. The essence of a fieldwork is to study natural phenomena in its proper context. Fieldworks dominantly utilize a learning-by-experiencing learning style and are often light on abstract thinking skills. We introduce more of the latter skills to a first-year fieldwork of several weeks by using Geographical Information Systems (GIS). We use simple techniques as the involved students had no prior experience with GIS. In our project, we introduced new tutorials prior to the fieldwork where students explored their research area using aerial photos, satellite images, an elevation model and slope-map using Google Earth and QGIS. The goal of these tutorials was to get acquainted with the area, plan the first steps of the fieldwork, and formulate hypotheses in form of a preliminary map based on quantitative data. During the actual fieldwork, half of the students processed and managed their field data using GIS, used elevation data as additional data source, and made digital geomorphological maps. This was in contrast to the other half of the students that used classic techniques with paper maps. We evaluated the learning benefits by two questionnaires (one before and one after the fieldwork), and a group interview with students that used GIS in the field. Students liked the use of Google Earth and GIS, and many indicate the added value of using quantitative maps. The hypotheses and fieldwork plans of the students were quickly superseded by insights during the fieldwork itself, but making these plans and hypotheses in advance improved the student's ability to perform empirical research. Students were very positive towards the use of GIS for their fieldwork, mainly because they experienced it as a modern and relevant technique for research and the labour market. Tech-savvy students were extra motivated and explored additional methods. There were some minor technical difficulties with using GIS during the fieldwork, but these can be solved by focussing the preparatory tutorials on what to expect during the fieldwork. We did not observe a significant difference in the quality of the products created by students between both groups since both digital and classic maps show a large range of aesthetic and scientific quality. To conclude, we had a positive experience with our first attempt to add GIS components to a classic fieldwork. The main benefit is that students use quantitative data which provides a different view on the fieldwork area and triggers abstract thinking. Future plans include using the student's field data in a web-gis app to allow easy remote supervision and using digital maps in the field.

Digital Terroir Mapping in the Tokaj Historical Wine Region

NASA Astrophysics Data System (ADS)

Pásztor, László; Lukácsy, György; Szabó, József; László, Péter; Burai, Péter; Bakacsi, Zsófia; Koós, Sándor; Laborczi, Annamária; Takács, Katalin; Bekő, László

2015-04-01

Tokaj is a historical region for botritized dessert wine making, the famed Tokaji Wine Region has the distinction of being Europe's first classified wine region. Very recently the sustainable quality wine production in the region was targeted, which requires detailed and "terroir-based approach" characterization of viticultural land. Tokaj region consists of 27 villages, the total producing vineyard surface area is 5,500 hectares, and the total vineyard land exceeds 11,000 hectares. The Tokaj Kereskedőház Ltd. is the only state owned winery in Hungary. The company is integrating grapes for wine production from 1,100 hectares of vineyard, which consist of 3,500 parcels with average size of 0.3 hectares. In 2013 the Hungarian Government has decided to elaborate a sustainable quality wine production in the Tokaj region coordinated by the Tokaj Kereskedőház Ltd, the biggest wine producer. To achieve the target it is indispensable to assess the viticultural potential of the land. In 2013 the characterization of the vineyard land potential was started collecting detailed, up-to-date information on the main environmental factors (geology, geomorphology and soil) which comprise the terroir effect and combined with legacy data of climate. The Council of Wine Communities of Tokaj Region has decided to widen the survey for the whole wine region in the year 2014. The primary objective of our work was the execution of an appropriate terroir zoning, which was carried out by digital terroir mapping. As a start-up we adapted some concepts recently applied in French wine regions. The implementation was however carried out totally in spatial, digital environment. Four main sources of information have been used (i) airborne laser scanning, (ii) hyperspectral imaginary, (iii) digital soil maps compiled based on detailed soil survey and (iv) interpolated climatic data. Based on them pedoclimate, mesoclimate and soil water reservoir were spatially predicted. The operational spatial resolution was set to 25 meters as a compromise between the denser remotely sensed data and the resolution available by the spatial inference of the collected soil information by proper digital soil mapping techniques. Finally the plant available water content, the vigor potential and precocity (earliness) potential was calculated. Based on these three maps the optimal target of production (dessert wine, dry wine, sparkling wine) could be determined and the information could provide a basis for decisions made both prior to planting and during production. Acknowledgement: The authors are grateful to the Tokaj Kereskedőház Ltd. and to András Tombor, Head of the Supervisory Board of Tokaj Kereskedőház Ltd. who has been supporting the project for the survey of the state of vineyards. Digital soil mapping was partly supported by the Hungarian National Scientific Research Foundation (OTKA, Grant No. K105167).

LiDAR DTMs and anthropogenic feature extraction: testing the feasibility of geomorphometric parameters in floodplains

NASA Astrophysics Data System (ADS)

Sofia, G.; Tarolli, P.; Dalla Fontana, G.

2012-04-01

In floodplains, massive investments in land reclamation have always played an important role in the past for flood protection. In these contexts, human alteration is reflected by artificial features ('Anthropogenic features'), such as banks, levees or road scarps, that constantly increase and change, in response to the rapid growth of human populations. For these areas, various existing and emerging applications require up-to-date, accurate and sufficiently attributed digital data, but such information is usually lacking, especially when dealing with large-scale applications. More recently, National or Local Mapping Agencies, in Europe, are moving towards the generation of digital topographic information that conforms to reality and are highly reliable and up to date. LiDAR Digital Terrain Models (DTMs) covering large areas are readily available for public authorities, and there is a greater and more widespread interest in the application of such information by agencies responsible for land management for the development of automated methods aimed at solving geomorphological and hydrological problems. Automatic feature recognition based upon DTMs can offer, for large-scale applications, a quick and accurate method that can help in improving topographic databases, and that can overcome some of the problems associated with traditional, field-based, geomorphological mapping, such as restrictions on access, and constraints of time or costs. Although anthropogenic features as levees and road scarps are artificial structures that actually do not belong to what is usually defined as the bare ground surface, they are implicitly embedded in digital terrain models (DTMs). Automatic feature recognition based upon DTMs, therefore, can offer a quick and accurate method that does not require additional data, and that can help in improving flood defense asset information, flood modeling or other applications. In natural contexts, morphological indicators derived from high resolution topography have been proven to be reliable for feasible applications. The use of statistical operators as thresholds for these geomorphic parameters, furthermore, showed a high reliability for feature extraction in mountainous environments. The goal of this research is to test if these morphological indicators and objective thresholds can be feasible also in floodplains, where features assume different characteristics and other artificial disturbances might be present. In the work, three different geomorphic parameters are tested and applied at different scales on a LiDAR DTM of typical alluvial plain's area in the North East of Italy. The box-plot is applied to identify the threshold for feature extraction, and a filtering procedure is proposed, to improve the quality of the final results. The effectiveness of the different geomorphic parameters is analyzed, comparing automatically derived features with the surveyed ones. The results highlight the capability of high resolution topography, geomorphic indicators and statistical thresholds for anthropogenic features extraction and characterization in a floodplains context.

Intensity of geomorphological processes in NW sector of Pacific rim marginal mountain belts

NASA Astrophysics Data System (ADS)

Lebedeva, Ekaterina; Shvarev, Sergey; Gotvansky, Veniamin

2014-05-01

Continental marginal mountains, including the mountain belts of Russian Far East, are characterized by supreme terrain contrast, mosaic structure of surface and crust, and rich complex of modern endogenous processes - volcanism, seismicity, and vertical movements. Unstable state of geomorphological systems and activity of relief forming processes here is caused also by deep dissected topography and the type and amount of precipitation. Human activities further stimulate natural processes and increase the risk of local disasters. So these territories have high intensity (or tension) of geomorphological processes. Intensity in the authors' understanding is willingness of geomorphological system to be out of balance, risk of disaster under external and internal agent, both natural and human. Mapping with quantitative accounting of intensity of natural and human potential impact is necessary for indication the areal distribution trends of geomorphological processes intensity and zones of potential risk of disasters. Methods of map drowning up are based on several criteria analyzing: 1) total terrain-form processes and their willingness to be a hazard-like, 2) existence, peculiarity and zoning of external agents which could cause extreme character of base processes within the territory, 3) peculiarity of terrain morphology which could cause hazard way of terrain-form processes. Seismic activity is one of the most important factors causing activation of geomorphological processes and contributing to the risk of dangerous situations. Earthquake even small force can provoke many catastrophic processes: landslides, mudslides, avalanches and mudflows, tsunami and others. Seismic gravitational phenomenons of different scale accompany almost all earthquakes of intensity 7-8 points and above, and some processes, such as avalanches, activated by seismic shocks intensity about 1-3 points. In this regard, we consider it important selection of high intensity seismic zones in marginal-continental mountain systems and also offer to give them extra points of tension, the number of which increases depending on the strength of the shock. Such approach allows to identify clearly the most potentially hazardous areas where there may be various, sometimes unpredictable scale catastrophic processes, provoked intense underground tremors. We also consider the impact of the depth of topography dissection and the total amount of precipitation. The marginal-continental mountain systems have often radically different moistening of coastal and inland slopes. And this difference can be 500, 1000 mm and more, that, undoubtedly, affects the course and intensity of geomorphological processes on slopes of different exposures. The total evaluation of intensity of geomorphologic processes exceeding 15 points is considered to be potentially catastrophic. At 10-15 points tension geomorphologic processes is extremely high, and at 5-10 points - high, less than 5 points - low. The maps of the key areas of the Russian Far East - Kamchatka and the north of Kuril Islands, Sakhalin and the Western Okhotsk region were compiled. These areas have differences in geodynamic regimes, landscape-climatic and anthropogenic conditions and highly significant in relation to the differentiated estimation of geomorphologic tension. The growth of intensity of geomorphological processes toward the Pacific Ocean was recorded: from 7-10 points in Western Okhotsk region to 10-13 at Sakhalin and to 13-15 points for Kamchatka.

Machine processing of remotely sensed data - quantifying global process: Models, sensor systems, and analytical methods; Proceedings of the Eleventh International Symposium, Purdue University, West Lafayette, IN, June 25-27, 1985

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mengel, S.K.; Morrison, D.B.

1985-01-01

Consideration is given to global biogeochemical issues, image processing, remote sensing of tropical environments, global processes, geology, landcover hydrology, and ecosystems modeling. Topics discussed include multisensor remote sensing strategies, geographic information systems, radars, and agricultural remote sensing. Papers are presented on fast feature extraction; a computational approach for adjusting TM imagery terrain distortions; the segmentation of a textured image by a maximum likelihood classifier; analysis of MSS Landsat data; sun angle and background effects on spectral response of simulated forest canopies; an integrated approach for vegetation/landcover mapping with digital Landsat images; geological and geomorphological studies using an image processing technique;more » and wavelength intensity indices in relation to tree conditions and leaf-nutrient content.« less

Geomorphological mapping of shallow landslides using UAVs

NASA Astrophysics Data System (ADS)

Fiorucci, Federica; Giordan, Daniele; Dutto, Furio; Rossi, Mauro; Guzzetti, Fausto

2015-04-01

The mapping of event shallow landslides is a critical activity, due to the large number of phenomena, mostly with small dimension, affecting extensive areas. This is commonly done through aerial photo-interpretation or through field surveys. Nowadays, landslide maps can be realized exploiting other methods/technologies: (i) airborne LiDARs, (ii) stereoscopic satellite images, and (iii) unmanned aerial vehicles (UAVs). In addition to the landslide maps, these methods/technologies allow the generation of updated Digital Terrain Models (DTM). In December 2013, in the Collazzone area (Umbria, Central Italy), an intense rainfall event triggered a large number of shallow landslides. To map the landslides occurred in the area, we exploited data and images obtained through (A) an airborne LiDAR survey, (B) a remote controlled optocopter (equipped with a Canon EOS M) survey, and (C) a stereoscopic satellite WorldView II MS. To evaluate the mapping accuracy of these methods, we select two landslides and we mapped them using a GPS RTK instrumentation. We consider the GPS survey as the benchmark being the most accurate system. The results of the comparison allow to highlight pros and cons of the methods/technologies used. LiDAR can be considered the most accurate system and in addition it allows the extraction and the classification of the digital surface models from the surveyed point cloud. Conversely, LiDAR requires additional time for the flight planning, and specific data analysis user capabilities. The analysis of the satellite WorldView II MS images facilitates the landslide mapping over large areas, but at the expenses of a minor resolution to detect the smaller landslides and their boundaries. UAVs can be considered the cheapest and fastest solution for the acquisition of high resolution ortho-photographs on limited areas, and the best solution for a multi-temporal analysis of specific landslide phenomena. Limitations are due to (i) the needs of optimal climatic conditions during the acquisition, (ii) the needs of ground control points to be acquired simultaneously with the UAV surveys, and (iii) the restrictive laws existing in different countries that could limit the use of these systems.

Geomorphology and reflectance patterns of vegetation-covered dunes at the Tsodilo Hills, north-west Botswana

NASA Technical Reports Server (NTRS)

Jacobberger, P. A.; Hooper, D. M.

1991-01-01

Seasonal reflectance variations in semigrid environments provide a means of assessing vegetation health and density as well as monitoring landform processes. Multitemporal Landsat Thematic Mapper scenes with field measurements are used to map geomorphology and vegetation density in a stabilized dune environment and to measure seasonal reflectance changes for a series of ten geomorphological and vegetation units on the Kalahari-age linear dunes. Units were chosen based on differences in landform and proportion of trees, forbs and bare soil. Reflectance curves and normalized-difference vegetation indices (NDVI) show that dune crests have the strongest seasonal variability in color and brightness. The geomorphological link with reflectance and NDVI values are linked to biomass production and zoning of vegetation with slope, drainage and subtle soil differences.

Stream piracy in the Black Hills: A geomorphology lab exercise

USGS Publications Warehouse

Zaprowski, B.J.; Evenson, E.B.; Epstein, J.B.

2002-01-01

The Black Hills of South Dakota exhibits many fine examples of stream piracy that are very suitable for teaching geomorphology lab exercises. This lab goes beyond standard topographic map interpretation by using geologic maps, well logs, gravel provenance and other types of data to teach students about stream piracy. Using a step-by-step method in which the lab exercises ramp up in difficulty, students hone their skills in deductive reasoning and data assimilation. The first exercises deal with the identification of stream piracy at a variety of spatial scales and the lab culminates with an exercise on landscape evolution and drainage rearrangement.

Geologic Map of the Shakespeare Quadrangle (H03), Mercury

NASA Astrophysics Data System (ADS)

Guzzetta, L.; Galluzzi, V.; Ferranti, L.; Palumbo, P.

2018-05-01

A 1:3M geological map of the H03 Shakespeare quadrangle of Mercury has been compiled through photointerpretation of the MESSENGER images. The most prominent geomorphological feature is the Caloris basin, the largest impact crater on Mercury.

Geomorphological mapping and geotechnical testing of the March 22, 2014, SR530 landslide near Oso, Washington

NASA Astrophysics Data System (ADS)

Collins, B. D.; Reid, M. E.; Vallance, J. W.; Iverson, R. M.; Schmidt, K. M.

2014-12-01

The March 22, 2014 landslide near Oso, Washington devastated a community, killing 43 people, destroying dozens of homes, and temporarily closing a section of State Route (SR) 530. The landslide, characterized as a debris avalanche - debris flow - rotational slide, was triggered by heavy precipitation in the region and initiated from a 200 m tall section of Pleistocene glacial deposits. The entire landslide encompassed an area of 1.2 km2. To understand the mobility of this landslide, we performed geological and geomorphological mapping throughout the initiation, transport, and deposition zones. In addition, we mapped a 450-m-long cross-section through the western distal lobe created by the excavation to reopen the SR530 roadbed to temporary traffic. Samples collected during mapping were used for geotechnical testing to evaluate the mobility of the landslide materials. Our detailed (1:300) geological mapping of the excavation revealed the juxtaposition of sand (glacial outwash) and clay (glaciolacustrine) debris avalanche hummocks towards the distal end of the landslide. Further, we found that two sections of the roadbed, having a combined length of at least 150 m, were entrained in the landslide. Throughout the debris avalanche deposit, 1:1200-scale geomorphological mapping identified a preponderance of sand boils located within thinner deposits between hummocks, suggesting that liquefaction played a role in the landslides mobility. In the central distal end of the landslide, we mapped on-lap deposits, wherein distal debris flow material overrode smaller hummocks of the larger debris avalanche deposit. Discovery of these deposits indicates that the run out of the landslide might have been even longer in places had topographic barriers (i.e., the other side of the valley) not reflected the flow back towards itself.

Bathymetry & Geomorphology - A New Seafloor Mapping of the Israeli Exclusive Economic Zone

NASA Astrophysics Data System (ADS)

Tibor, G.; Hall, J. K.; Kanari, M.; Sade, R. A.; Sade, H.; Amit, G.; Gur-Arie, L.; Ketter, T.

2017-12-01

Recent extensive activities of oil and gas exploration and production companies in the Israeli Exclusive Economic Zone (EEZ) raised the need for an up-to-date baseline mapping of the seafloor to assist policy makers. The baseline mapping focused on bathymetry, geomorphology, geology, biodiversity, infauna and habitat in order to compile a sensitivity map for the Petroleum Commissioner in the Ministry of Energy in the bid for opening the sea to new natural gas and oil explorations. The Israeli EEZ covers an area of 25,950 sq. km. and reaches a maximum water depth of 2,100 m. It is located within the Levantine Basin, a zone of compression and strike-slip tectonics as Africa pushes into Eurasia. These forces operate on a half kilometer thick of Messinian evaporates and over a dozen kilometers of Pliocene and Pleistocene sediments to produce a complex seafloor morphology. The margin is cut by numerous slumps and canyons, while the basin is traversed by deep sea channels emptying into the moat around Eratosthenes Seamount farther north. The bathymetric and geomorphological mapping was done in three phases using Kongsberg and Elac multibeam sonars installed on different research vessels. The last phase (Aug.-Sept., 2016) covering depths from 1,400 to 2,100 m used the Kongsberg EM302 sonar installed on our new governmental research vessel Bat Galim. It has "state of the art" capabilities to map, sample and analyze the water column, seafloor and sub-bottom from water depths of 10m to 7,000 m. These mapping capabilities are unique in our region, the Eastern Mediterranean and the Red Sea, so we hope to promote research collaborations with our neighbors.

Linear programming model to develop geodiversity map using utility theory

NASA Astrophysics Data System (ADS)

Sepehr, Adel

2015-04-01

In this article, the classification and mapping of geodiversity based on a quantitative methodology was accomplished using linear programming, the central idea of which being that geosites and geomorphosites as main indicators of geodiversity can be evaluated by utility theory. A linear programming method was applied for geodiversity mapping over Khorasan-razavi province located in eastern north of Iran. In this route, the main criteria for distinguishing geodiversity potential in the studied area were considered regarding rocks type (lithology), faults position (tectonic process), karst area (dynamic process), Aeolian landforms frequency and surface river forms. These parameters were investigated by thematic maps including geology, topography and geomorphology at scales 1:100'000, 1:50'000 and 1:250'000 separately, imagery data involving SPOT, ETM+ (Landsat 7) and field operations directly. The geological thematic layer was simplified from the original map using a practical lithologic criterion based on a primary genetic rocks classification representing metamorphic, igneous and sedimentary rocks. The geomorphology map was provided using DEM at scale 30m extracted by ASTER data, geology and google earth images. The geology map shows tectonic status and geomorphology indicated dynamic processes and landform (karst, Aeolian and river). Then, according to the utility theory algorithms, we proposed a linear programming to classify geodiversity degree in the studied area based on geology/morphology parameters. The algorithm used in the methodology was consisted a linear function to be maximized geodiversity to certain constraints in the form of linear equations. The results of this research indicated three classes of geodiversity potential including low, medium and high status. The geodiversity potential shows satisfied conditions in the Karstic areas and Aeolian landscape. Also the utility theory used in the research has been decreased uncertainty of the evaluations.

Rockfall hazard mapping along a mountainous road in Switzerland using a GIS-based parameter rating approach

NASA Astrophysics Data System (ADS)

Baillifard, F.; Jaboyedoff, M.; Sartori, M.

A posteriori studies of rock slope instabilities generally show that rockfalls do not occur at random locations: the failure zone can be classified as sensitive from geomorphological evidence. Zones susceptible to failure can there-fore be detected. Effects resulting from degrading and triggering factors, such as groundwater circulation and freeze and thaw cycles, must then be assessed in order to evaluate the probability of failure. A simple method to detect rock slope instabilities was tested in a study involving a 2000 m3 rockfall that obstructed a mountainous road near Sion (Switzerland) on 9 January 2001. In order to locate areas from which a rock-fall might originate, areas were assessed with respect to the presence or absence of five criteria: (1) a fault, (2) a scree slope within a short distance, (3) a rocky cliff, (4) a steep slope, and (5) a road. These criteria were integrated into a Geographic Information System (GIS) using existing topo-graphic, geomorphological, and geological vector and raster digital data. The proposed model yields a rating from 0 to 5, and gives a relative hazard map. Areas yielding a high relative hazard have to meet two additional criteria if they are to be considered as locations from which a rockfall might originate: (1) the local structural pattern has to be unfavourable, and (2) the morphology has to be susceptible to the effects of degrading and triggering factors. The rockfall of 9 January 2001, has a score of 5. Applied to the entire length of the road (4 km), the present method reveals two additional areas with a high relative hazard, and allows the detection of the main instabilities of the site.

GIS representation of coal-bearing areas in Antarctica

USGS Publications Warehouse

Merrill, Matthew D.

2016-03-11

Understanding the distribution of coal-bearing geologic units in Antarctica provides information that can be used in sedimentary, geomorphological, paleontological, and climatological studies. This report is a digital compilation of information on Antarctica’s coal-bearing geologic units found in the literature. It is intended to be used in small-scale spatial geographic information system (GIS) investigations and as a visual aid in the discussion of Antarctica’s coal resources or in other coal-based geologic investigations. Instead of using spatially insignificant point markers to represent large coal-bearing areas, this dataset uses polygons to represent actual coal-bearing lithologic units. Specific locations of coal deposits confirmed from the literature are provided in the attribution for the coal-bearing unit polygons. Coal-sample-location data were used to confirm some reported coal-bearing geology. The age and extent of the coal deposits indicated in the literature were checked against geologic maps ranging from local scale at 1:50,000 to Antarctic continental scale at 1:5,000,000; if satisfactory, the map boundaries were used to generate the polygons for the coal-bearing localities.

Geomorphological map and preliminary analysis of Quaternary sediments in the Planica-Tamar valley (Julian Alps, NW Slovenia)

NASA Astrophysics Data System (ADS)

Novak, Andrej; Šmuc, Andrej

2016-04-01

The Planica-Tamar valley is located in the Julian Alps in north-west Slovenia. The Planica-Tamar valley represents typical mountain glacial valley bounded by steep, mainly carbonate cliffs with some glacial deposits still preserved. The valley is currently being filled with numerous Holocene sediments deposited by rock falls, landslides, mass gravity flows and fluvial flows. These deposits are forming active or inactive interfingering talus slopes, alluvial and debris-flow fans, all of them with a complex history of sedimentation and erosion forming unconformity bounded sedimentary units. In order to make a thorough analysis of these deposits a detailed geomorphological map in a scale of 1:10 000 has been made. Six different types of sedimentary deposits were defined and mapped. These are moraines, lacustrine sediments, fluvio-glacial deposits, talus slopes, debris fans and alluvial fans. Other mapped features also include shape of ravines, their depths, ridges and direction of sedimentary flow. Additionally areas of active, semi-active and inactive sedimentation were marked. Moraines forms a ridge in the bottom of the valleys and are composed of unconsolidated, poorly sorted, subangular grains ranging from clay size to a few cubic meters big blocks. Lacustrine sediments are represented by laminated well sorted sand and silt, while fluvio-glacial deposits are composed of washed out subrounded sands and gravels. Talus slope deposits are characterised by clast-supported poorly sorted very angular gravel. Debris flow fans are represented by extremely poorly sorted matrix-supported gravels with grain size ranging from clay to few cubic meters big blocks. Alluvial fans are composed by variety of sedimentary textures. Sediments at the fan apex are clast-supported poorly sorted very angular gravels with up to a few cubic meters big block. In the middle part of the fan the sieve deposits are common, while in the distal parts a few centimeters thick layers of sand and moderately sorted clast or sandy matrix-supported angular gravels occur. In cross-sections of alluvial fans distinct palaeosoil horizons are present indicating longer inactivity of that part of the fan. The geomorphological map forms a base for further research and thorough analysis of Quaternary deposits in order to reconstruct the Holocene dynamic of triggering and sedimentation of different types of slope deposits and relate them to base rock geology, tectonic and local/regional climate events. Key words: geomorphological mapping, Holocene slope deposits, alluvial fans, debris fans, Alpine geomorphology.

Swift delineation of flood-prone areas over large European regions

NASA Astrophysics Data System (ADS)

Tavares da Costa, Ricardo; Castellarin, Attilio; Manfreda, Salvatore; Samela, Caterina; Domeneghetti, Alessio; Mazzoli, Paolo; Luzzi, Valerio; Bagli, Stefano

2017-04-01

According to the European Environment Agency (EEA Report No 1/2016), a significant share of the European population is estimated to be living on or near a floodplain, with Italy having the highest population density in flood-prone areas among the countries analysed. This tendency, tied with event frequency and magnitude (e.g.: the 24/11/2016 floods in Italy) and the fact that river floods may occur at large scales and at a transboundary level, where data is often sparse, presents a challenge in flood-risk management. The availability of consistent flood hazard and risk maps during prevention, preparedness, response and recovery phases are a valuable and important step forward in improving the effectiveness, efficiency and robustness of evidence-based decision making. The present work aims at testing and discussing the usefulness of pattern recognition techniques based on geomorphologic indices (Manfreda et al., J. Hydrol. Eng., 2011, Degiorgis et al., J Hydrol., 2012, Samela et al., J. Hydrol. Eng., 2015) for the simplified mapping of river flood-prone areas at large scales. The techniques are applied to 25m Digital Elevation Models (DEM) of the Danube, Po and Severn river watersheds, obtained from the Copernicus data and information funded by the European Union - EU-DEM layers. Results are compared to the Pan-European flood hazard maps derived by Alfieri et al. (Hydrol. Proc., 2013) using a set of distributed hydrological (LISFLOOD, van der Knijff et al., Int. J. Geogr. Inf. Sci., 2010, employed within the European Flood Awareness System, www.efas.eu) and hydraulic models (LISFLOOD-FP, Bates and De Roo, J. Hydrol., 2000). Our study presents different calibration and cross-validation exercises of the DEM-based mapping algorithms to assess to which extent, and with which accuracy, they can be reproduced over different regions of Europe. This work is being developed under the System-Risk project (www.system-risk.eu) that received funding from the European Union's Framework Programme for Research and Innovation Horizon 2020 under the Marie Skłodowska-Curie Grant Agreement No. 676027. Keywords: flood hazard, data-scarce regions, large-scale studies, pattern recognition, linear binary classifiers, basin geomorphology, DEM.

Revisiting Melton: Analyzing the correlation structure of geomorphological and climatological parameters

NASA Astrophysics Data System (ADS)

Carothers, R. A.; Sangireddy, H.; Passalacqua, P.

2013-12-01

In his expansive 1957 study of over 80 basins in Arizona, Colorado, New Mexico, and Utah, Mark Melton measured key morphometric, soil, land cover, and climatic parameters [Melton, 1957]. He identified correlations between morphological parameters and climatic regimes in an attempt to characterize the geomorphology of the basin as a function of climate and vegetation. Using modern techniques such as high resolution digital terrain models in combination with high spatial resolution weather station records, vector soil maps, seamless raster geological data, and land cover vector maps, we revisit Melton's 1957 dataset with the following hypotheses: (1) Patterns of channelization carry strong, codependent signatures in the form of statistical correlations of rainfall variability, soil type, and vegetation patterns. (2) Channelization patterns reflect the erosion processes on sub-catchment scale and the subsequent processes of vegetation recovery and gullying. In order to characterize various topographic and climatic parameters, we obtain elevation and land cover data from the USGS National Elevation dataset, climate data from the Western Regional Climate Center and PRISM climate group database, and soil type from the USDA STATSGO soil database. We generate a correlative high resolution database on vegetation, soil cover, lithology, and climatology for the basins identified by Melton in his 1957 study. Using the GeoNet framework developed by Passalacqua et al. [2010], we extract various morphological parameters such as slope, drainage density, and stream frequency. We also calculate metrics for patterns of channelization such as number of channelized pixels in a basin and channel head density. In order to understand the correlation structure between climate and morphological variables, we compute the Pearson's correlation coefficient similar to Melton's analysis and also explore other statistical procedures to characterize the feedbacks between these variables. By identifying the differences in Melton's and our results, we address the influence of climate over the degree of channel dissection in the landscape. References: Melton, M. A. (1957). An analysis of the relations among elements of climate, surface properties, and geomorphology (No. CU-TR-11). COLUMBIA UNIV NEW YORK Passalacqua, P., Do Trung, T., Foufoula-Georgiou, E., Sapiro, G., & Dietrich, W. E. (2010). A geometric framework for channel network extraction from lidar: Nonlinear diffusion and geodesic paths. Journal of Geophysical Research: Earth Surface (2003-2012), 115(F1). PRISM Climate Group, Oregon State University, http://prism.oregonstate.edu, created 4 Feb 2004 Soil Survey Staff, Natural Resources Conservation Service, United States Department of Agriculture. U.S. General Soil Map (STATSGO2). Available online at http://soildatamart.nrcs.usda.gov USGS National Map Viewer, United States Geological Survey. Web. 10 June 2013. http://viewer.nationalmap.gov/viewer/ Western U.S. Historical Climate Summaries, Western Regional Climate Group, 2013. Web. 10 June 2013. http://www.wrcc.dri.edu/Climsum.html

Comparison of different landform classification methods for digital landform and soil mapping of the Iranian loess plateau

NASA Astrophysics Data System (ADS)

Hoffmeister, Dirk; Kramm, Tanja; Curdt, Constanze; Maleki, Sedigheh; Khormali, Farhad; Kehl, Martin

2016-04-01

The Iranian loess plateau is covered by loess deposits, up to 70 m thick. Tectonic uplift triggered deep erosion and valley incision into the loess and underlying marine deposits. Soil development strongly relates to the aspect of these incised slopes, because on northern slopes vegetation protects the soil surface against erosion and facilitates formation and preservation of a Cambisol, whereas on south-facing slopes soils were probably eroded and weakly developed Entisols formed. While the whole area is intensively stocked with sheep and goat, rain-fed cropping of winter wheat is practiced on the valley floors. Most time of the year, the soil surface is unprotected against rainfall, which is one of the factors promoting soil erosion and serious flooding. However, little information is available on soil distribution, plant cover and the geomorphological evolution of the plateau, as well as on potentials and problems in land use. Thus, digital landform and soil mapping is needed. As a requirement of digital landform and soil mapping, four different landform classification methods were compared and evaluated. These geomorphometric classifications were run on two different scales. On the whole area an ASTER GDEM and SRTM dataset (30 m pixel resolution) was used. Likewise, two high-resolution digital elevation models were derived from Pléiades satellite stereo-imagery (< 1m pixel resolution, 10 by 10 km). The high-resolution information of this dataset was aggregated to datasets of 5 and 10 m scale. The applied classification methods are the Geomorphons approach, an object-based image approach, the topographical position index and a mainly slope based approach. The accuracy of the classification was checked with a location related image dataset obtained in a field survey (n ~ 150) in September 2015. The accuracy of the DEMs was compared to measured DGPS trenches and map-based elevation data. The overall derived accuracy of the landform classification based on the high-resolution DEM with a resolution of 5 m is approximately 70% and on a 10 m resolution >58%. For the 30 m resolution datasets is the achieved accuracy approximately 40%, as several small scale features are not recognizable in this resolution. Thus, for an accurate differentiation between different important landform types, high-resolution datasets are necessary for this strongly shaped area. One major problem of this approach are the different classes derived by each method and the various class annotations. The result of this evaluation will be regarded for the derivation of landform and soil maps.

Tectonic geomorphology of the Safeen Anticline (Northern Iraq)

NASA Astrophysics Data System (ADS)

Bartl, N.; Grasemann, B.; Faber, R.; Lockhart, D.

2009-04-01

The Zagros Fold- and Thrust Belt extends over 1800 km from Kurdistan in N-Iraq to the Strait of Hormuz in Iran and is one of the world most promising regions for the future hydrocarbon exploration. The Zagros Mountains are the result of the collision of the Eurasian and the Arabian Plates starting in the Late Cretaceous. Recent GPS measurements in have shown that the shortening between these two plates is about 2.5 cm/a most of which is distributed within the Zagros collision orogen. Whereas the tectonic structure and the geomorphological response to active deformation is thoroughly studied in the SE part of the Zagros in Iran, there are almost no modern field based studies of the NW part of the Zagros in Iraq. Here we present the first structural field studies, the mechanical stratigraphy and geomorphological investigations of the Safeen anticline in the NE of the city of Erbil in the Kurdistan region, which is a province of Northern Iraq. The sub-cylindrical part of the anticline strikes for about 65 km NW-SE and has a dominant wavelength of about 6 km. Perpendicular to the strike of the anticline Cretaceous to Tertiary sediments are exposed consisting mainly of bedded to massif limestones and sandstones (competent lithologies), intercalated with marl and claystones (incompetent lithologies). Whereas deformation in the competent lithologies is accommodated by diffusive mass transfer processes and mainly fracturing, the incompetent lithologies record distributed plastic deformation. Along the investigated section, the limbs of the anticline dip with 55° towards NE (backlimb) and 60° towards SW (forelimb). Interestingly the drainage pattern of the forelimb differs significantly to the erosional signature along the backlimb. Both limbs are dominated by transverse river segments. The backlimb records straight almost perpendicular to the fold axis with a spacing of the segments of about 200 m. The forelimb, however, is dominated by a more irregular pattern with a wider spacing of the main segments of about 600m. We use an ASTER digital elevation model in combination with the geological map in order to quantify the differences in geomorphological signal along the different limbs of the Safeen anticline.

Remote sensing studies and morphotectonic investigations in an arid rift setting, Baja California, Mexico

NASA Astrophysics Data System (ADS)

El-Sobky, Hesham Farouk

The Gulf of California and its surrounding land areas provide a classic example of recently rifted continental lithosphere. The recent tectonic history of eastern Baja California has been dominated by oblique rifting that began at ˜12 Ma. Thus, extensional tectonics, bedrock lithology, long-term climatic changes, and evolving surface processes have controlled the tectono-geomorphological evolution of the eastern part of the peninsula since that time. In this study, digital elevation data from the Shuttle Radar Topography Mission (SRTM) from Baja California were corrected and enhanced by replacing artifacts with real values that were derived using a series of geostatistical techniques. The next step was to generate accurate thematic geologic maps with high resolution (15-m) for the entire eastern coast of Baja California. The main approach that we used to clearly represent all the lithological units in the investigated area was objectoriented classification based on fuzzy logic theory. The area of study was divided into twenty-two blocks; each was classified independently on the basis of its own defined membership function. Overall accuracies were 89.6%, indicating that this approach was highly recommended over the most conventional classification techniques. The third step of this study was to assess the factors that affected the geomorphologic development along the eastern side of Baja California, where thirty-four drainage basins were extracted from a 15-m-resolution absolute digital elevation model (DEM). Thirty morphometric parameters were extracted; these parameters were then reduced using principal component analysis (PCA). Cluster analysis classification defined four major groups of basins. We extracted stream length-gradient indices, which highlight the differential rock uplift that has occurred along fault escarpments bounding the basins. Also, steepness and concavity indices were extracted for bedrock channels within the thirty-four drainage basins. The results were highly correlated with stream length-gradient indices for each basin. Nine basins, exhibiting steepness index values greater than 0.07, indicated a strong tectonic signature and possible higher uplift rates in these basins. Further, our results indicated that drainage basins in the eastern rift province of Baja California could be classified according to the dominant geomorphologic controlling factors (i.e., fault-controlled, lithology-controlled, or hybrid basins).

Bathymetric and underwater video survey of Lower Granite Reservoir and vicinity, Washington and Idaho, 2009-10

USGS Publications Warehouse

Williams, Marshall L.; Fosness, Ryan L.; Weakland, Rhonda J.

2012-01-01

The U.S. Geological Survey conducted a bathymetric survey of the Lower Granite Reservoir, Washington, using a multibeam echosounder, and an underwater video mapping survey during autumn 2009 and winter 2010. The surveys were conducted as part of the U.S. Army Corps of Engineer's study on sediment deposition and control in the reservoir. The multibeam echosounder survey was performed in 1-mile increments between river mile (RM) 130 and 142 on the Snake River, and between RM 0 and 2 on the Clearwater River. The result of the survey is a digital elevation dataset in ASCII coordinate positioning data (easting, northing, and elevation) useful in rendering a 3×3-foot point grid showing bed elevation and reservoir geomorphology. The underwater video mapping survey was conducted from RM 107.73 to 141.78 on the Snake River and RM 0 to 1.66 on the Clearwater River, along 61 U.S. Army Corps of Engineers established cross sections, and dredge material deposit transects. More than 900 videos and 90 bank photographs were used to characterize the sediment facies and ground-truth the multibeam echosounder data. Combined, the surveys were used to create a surficial sediment facies map that displays type of substrate, level of embeddedness, and presence of silt.

High-resolution mapping based on an Unmanned Aerial Vehicle (UAV) to capture paleoseismic offsets along the Altyn-Tagh fault, China.

PubMed

Gao, Mingxing; Xu, Xiwei; Klinger, Yann; van der Woerd, Jerome; Tapponnier, Paul

2017-08-15

The recent dramatic increase in millimeter- to centimeter- resolution topographic datasets obtained via multi-view photogrammetry raises the possibility of mapping detailed offset geomorphology and constraining the spatial characteristics of active faults. Here, for the first time, we applied this new method to acquire high-resolution imagery and generate topographic data along the Altyn Tagh fault, which is located in a remote high elevation area and shows preserved ancient earthquake surface ruptures. A digital elevation model (DEM) with a resolution of 0.065 m and an orthophoto with a resolution of 0.016 m were generated from these images. We identified piercing markers and reconstructed offsets based on both the orthoimage and the topography. The high-resolution UAV data were used to accurately measure the recent seismic offset. We obtained the recent offset of 7 ± 1 m. Combined with the high resolution satellite image, we measured cumulative offsets of 15 ± 2 m, 20 ± 2 m, 30 ± 2 m, which may be due to multiple paleo-earthquakes. Therefore, UAV mapping can provide fine-scale data for the assessment of the seismic hazards.

Quantitative Analysis of Venus Radar Backscatter Data in ArcGIS

NASA Technical Reports Server (NTRS)

Long, S. M.; Grosfils, E. B.

2005-01-01

Ongoing mapping of the Ganiki Planitia (V14) quadrangle of Venus and definition of material units has involved an integrated but qualitative analysis of Magellan radar backscatter images and topography using standard geomorphological mapping techniques. However, such analyses do not take full advantage of the quantitative information contained within the images. Analysis of the backscatter coefficient allows a much more rigorous statistical comparison between mapped units, permitting first order selfsimilarity tests of geographically separated materials assigned identical geomorphological labels. Such analyses cannot be performed directly on pixel (DN) values from Magellan backscatter images, because the pixels are scaled to the Muhleman law for radar echoes on Venus and are not corrected for latitudinal variations in incidence angle. Therefore, DN values must be converted based on pixel latitude back to their backscatter coefficient values before accurate statistical analysis can occur. Here we present a method for performing the conversions and analysis of Magellan backscatter data using commonly available ArcGIS software and illustrate the advantages of the process for geological mapping.

Satellite data in aquatic area research - Some ideas for future studies

NASA Technical Reports Server (NTRS)

Raitala, Jouko T.

1986-01-01

Attempts to apply aquatic remote sensing to the preparation of parametric map-like presentations, quantitative evaluations and time-related investigations in various water areas in Finland are presented. The potential use of Landsat MSS data in aquatic area studies, including limology, aquatic botany, geomorphology and engineering is evaluated using computer-aided digital remote sensing techniques. MSS data may provide information about depth, Secchi disc values, humus content in water, and productivity. Aquatic vegetation classification using MSS is possible only where vegetation units are large enough in respect to the 0.5 hectares ground resolution. Multitemporal satellite imagery has been used to evaluate alterations in the littoral areas of some Finnish water reservoirs between successive periods of high water. It is concluded that although MSS data can be of use in aquatic studies, it should be used in connection with field data and/or TM and SPOT data.

Drought Vulnerability Mapping with Geomorphological Approach in Yogyakarta Special Region (DIY) and Central Java

NASA Astrophysics Data System (ADS)

Sudaryatno

2016-11-01

This study aims to determine the level of vulnerability of the geomorphologic drought that occurred in Central Java and Yogyakarta Special Region. This study examines geomorphologic drought. Parameters used were slope, drainage, Available Water Capacity (AWC), permeability, landform, and land use. Landsat 8 and SRTM data were used for the extraction of physical parameters, such as slope, drainage, landform, and land use. The method used in this study is scoring and weighting. Query results were used for data classification by overlaying drought geomorphologic parameters. The expected outcome of this research is to map the geomorphologic drought vulnerability on Central Java and Yogyakarta Special Region. Drought vulnerability was divided into wet, normal and dry classes. Distribution of the dry class is frequent. Some of the dry classes are distributed on the steep till extremely steep slope region and on the structural and karsts landform. This was related to AWC value where region with high AWC contributed to the poor drainage of the soil, such as at Kulonprogo, Purworejo, Kebumen, Blora, Wonogiri, Purbalingga, Pekalongan, Jepara and Kudus regency. Normal classes are distributed on the sloping till steep slope, have moderate till well-drained soil and low AWC, such as at Gunung Kidul, Pati, Temanggung regency, and Magelang city. Wet classes are distributed on the flat or almost flat and sloping region. Most of the wet classes are distributed on volcanic hills and coastal area. Those regions are well-drained and the land uses are mostly for settlement and farming, such as at Sleman, Yogyakarta city, Klaten, Bantul, and Wonosobo regency.

Geology and geomorphology of the Carolina Sandhills, Chesterfield County, South Carolina

USGS Publications Warehouse

Swezey, Christopher; Fitzwater, Bradley A.; Whittecar, G. Richard

2016-01-01

This two-day field trip focuses on the geology and geomorphology of the Carolina Sandhills in Chesterfield County, South Carolina. This area is located in the updip portion of the U.S. Atlantic Coastal Plain province, supports an ecosystem of longleaf pine (Pinus palustris) and wiregrass (Aristida stricta), and contains three major geologic map units: (1) An ~60–120-m-thick unit of weakly consolidated sand, sandstone, mud, and gravel is mapped as the Upper Cretaceous Middendorf Formation and is interpreted as a fluvial deposit. This unit is capped by an unconformity, and displays reticulate mottling, plinthite, and other paleosol features at the unconformity. The Middendorf Formation is the largest aquifer in South Carolina. (2) A 0.3–10-m-thick unit of unconsolidated sand is mapped as the Quaternary Pinehurst Formation and is interpreted as deposits of eolian sand sheets and dunes derived via remobilization of sand from the underlying Cretaceous strata. This unit displays argillic horizons and abundant evidence of bioturbation by vegetation. (3) A <3-m-thick unit of sand, pebbly sand, sandy mud, and mud is mapped as Quaternary terrace deposits adjacent to modern drainages. In addition to the geologic units listed above, a prominent geomorphologic feature in the study area is a north-trending escarpment (incised by headwater streams) that forms a markedly asymmetric drainage divide. This drainage divide, as well as the Quaternary terraces deposits, are interpreted as evidence of landscape disequilibrium (possibly geomorphic responses to Quaternary climate changes).

Automatic identification of fault surfaces through Object Based Image Analysis of a Digital Elevation Model in the submarine area of the North Aegean Basin

NASA Astrophysics Data System (ADS)

Argyropoulou, Evangelia

2015-04-01

The current study was focused on the seafloor morphology of the North Aegean Basin in Greece, through Object Based Image Analysis (OBIA) using a Digital Elevation Model. The goal was the automatic extraction of morphologic and morphotectonic features, resulting into fault surface extraction. An Object Based Image Analysis approach was developed based on the bathymetric data and the extracted features, based on morphological criteria, were compared with the corresponding landforms derived through tectonic analysis. A digital elevation model of 150 meters spatial resolution was used. At first, slope, profile curvature, and percentile were extracted from this bathymetry grid. The OBIA approach was developed within the eCognition environment. Four segmentation levels were created having as a target "level 4". At level 4, the final classes of geomorphological features were classified: discontinuities, fault-like features and fault surfaces. On previous levels, additional landforms were also classified, such as continental platform and continental slope. The results of the developed approach were evaluated by two methods. At first, classification stability measures were computed within eCognition. Then, qualitative and quantitative comparison of the results took place with a reference tectonic map which has been created manually based on the analysis of seismic profiles. The results of this comparison were satisfactory, a fact which determines the correctness of the developed OBIA approach.

Mapping the Rainforest of the Sea: Global Coral Reef Maps for Global Conservation

NASA Technical Reports Server (NTRS)

Robinson, Julie A.

2006-01-01

Coral reefs are the center of marine biodiversity, yet are under threat with an estimated 60% of coral reef habitats considered at risk by the World Resources Institute. The location and extent of coral reefs in the world are the basic information required for resource management and as a baseline for monitoring change. A NASA sponsored partnership between remote sensing scientists, international agencies and NGOs, has developed a new generation of global reef maps based on data collected by satellites. The effort, dubbed the Millennium Coral Reef Map aims to develop new methods for wide distribution of voluminous satellite data of use to the conservation and management communities. We discuss the tradeoffs between remote sensing data sources, mapping objectives, and the needs for conservation and resource management. SeaWiFS data were used to produce a composite global shallow bathymetry map at 1 km resolution. Landsat 7/ETM+ data acquisition plans were modified to collect global reefs and new operational methods were designed to generate the firstever global coral reef geomorphology map. We discuss the challenges encountered to build these databases and in implementing the geospatial data distribution strategies. Conservation applications include a new assessment of the distribution of the world s marine protected areas (UNEPWCMC), improved spatial resolution in the Reefs at Risk analysis for the Caribbean (WRI), and a global basemap for the Census of Marine Life's OBIS database. The Millennium Coral Reef map and digital image archive will pay significant dividends for local and regional conservation projects around the globe. Complete details of the project are available at http://eol.jsc.nasa.gov/reefs.

Data without Frontiers - the International Quaternary Map of Europe (IQUAME 2500)

NASA Astrophysics Data System (ADS)

Asch, Kristine

2017-04-01

The Federal German Geological Survey (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR) is leading the review of the International Quaternary Map of Europe (IQUAME 2500) and its transformation into a geographical information system (GIS) under the umbrella of the CGMW and INQUA. It is a long-standing policy of BGR to lead international cooperation of European geological survey mapping projects. These particularly include projects under the umbrella of organisations including CGMW, UNESCO, INQUA, EGU and IUGS. The aim of IQUAME 2500 is to build a geological information system (GIS) of Europe's Quaternary geology where relevant information can be retrieved, combined and applied across international boundaries. Cross-border mapping poses specific challenges, in particular data harmonisation, for the presentation of regional geology. Overcoming these obstacles demands international cooperation with national geological survey organisations. Based on the previous BGR & UNESCO co-produced International Quaternary Map of Europe (at a 1 : 2,5 million scale; completed in 1995), revision was begun by BGR in 2011 to review the information available from an international group of experts from European geological survey organisations. This group is supported by an international academic Advisory Board. The work requires re-evaluation and digitization of the 14 paper sheets. For this purpose BGR developed a pragmatic procedure to classify, deliver and combine the reviewed Quaternary data in a harmonized and uniform manner. The project is applying the vocabularies and data model of the EC Directive INSPIRE Directive and is creating additional vocabularies and definitions for necessary features such as geomorphology (with the EMODnet project) and glaciogenic elements. An academic scientific advisory board is overseeing the process. Subjects of the map include: geological boundaries and classifications of Quaternary rocks, extension and boundaries of permafrost, last glacial maximum, genetic descriptions of the rocks, faults, key localities (geologically and palaeontologically significant sites, anthropological sites, impact craters, etc.) and more detailed off-shore geology (in cooperation with the EMODnet project). Ultimately, the IQUAME project will summarise the current status quo of European Quaternary geological research in a digitally available GIS synthesis and introduce practically applicable new vocabularies to describe the results and share those with the science community.

Geomorphological analysis and classification of foredune ridges based on Terrestrial Laser Scanning (TLS) technology

NASA Astrophysics Data System (ADS)

Fabbri, Stefano; Giambastiani, Beatrice M. S.; Sistilli, Flavia; Scarelli, Frederico; Gabbianelli, Giovanni

2017-10-01

Along the North Adriatic Sea coast (Italy), vulnerability to climate change is further aggravated by anthropogenic influences, such as strong subsidence rate due to deep groundwater and gas abstraction, tourism and industry impacts. In this context, conservation and restoration of coastal sand dunes become extremely important especially because of their importance in terms of 'natural' coastal defense. This paper proposes an innovative geomorphological approach based on Terrestrial Laser Scanning - TLS, which allows us to measure and monitor morphometric dune evolution with high precision and details. Several TLS surveys were performed along the Ravenna coast (Adriatic Sea, Italy) and the resulting Digital Elevation Models (DEMs) were analyzed in order to classify the foredune ridges in three geomorphological sub-zones. The topographic, areal and volumetric variations over time of geomorphological units were calculated by GIS tools in order to identify seasonal trends or particular pattern. Meteo-marine climate conditions were also analyzed and Principal Component Analysis (PCA) was performed to correlate changes in morphology with meteo-marine forcing factors, highlighting the ones that most influence dune evolution and dynamics.

Habitat Hydrology and Geomorphology Control the Distribution of Malaria Vector Larvae in Rural Africa

PubMed Central

Hardy, Andrew J.; Gamarra, Javier G. P.; Cross, Dónall E.; Macklin, Mark G.; Smith, Mark W.; Kihonda, Japhet; Killeen, Gerry F.; Ling’ala, George N.; Thomas, Chris J.

2013-01-01

Background Larval source management is a promising component of integrated malaria control and elimination. This requires development of a framework to target productive locations through process-based understanding of habitat hydrology and geomorphology. Methods We conducted the first catchment scale study of fine resolution spatial and temporal variation in Anopheles habitat and productivity in relation to rainfall, hydrology and geomorphology for a high malaria transmission area of Tanzania. Results Monthly aggregates of rainfall, river stage and water table were not significantly related to the abundance of vector larvae. However, these metrics showed strong explanatory power to predict mosquito larval abundances after stratification by water body type, with a clear seasonal trend for each, defined on the basis of its geomorphological setting and origin. Conclusion Hydrological and geomorphological processes governing the availability and productivity of Anopheles breeding habitat need to be understood at the local scale for which larval source management is implemented in order to effectively target larval source interventions. Mapping and monitoring these processes is a well-established practice providing a tractable way forward for developing important malaria management tools. PMID:24312606

Habitat hydrology and geomorphology control the distribution of malaria vector larvae in rural Africa.

PubMed

Hardy, Andrew J; Gamarra, Javier G P; Cross, Dónall E; Macklin, Mark G; Smith, Mark W; Kihonda, Japhet; Killeen, Gerry F; Ling'ala, George N; Thomas, Chris J

2013-01-01

Larval source management is a promising component of integrated malaria control and elimination. This requires development of a framework to target productive locations through process-based understanding of habitat hydrology and geomorphology. We conducted the first catchment scale study of fine resolution spatial and temporal variation in Anopheles habitat and productivity in relation to rainfall, hydrology and geomorphology for a high malaria transmission area of Tanzania. Monthly aggregates of rainfall, river stage and water table were not significantly related to the abundance of vector larvae. However, these metrics showed strong explanatory power to predict mosquito larval abundances after stratification by water body type, with a clear seasonal trend for each, defined on the basis of its geomorphological setting and origin. Hydrological and geomorphological processes governing the availability and productivity of Anopheles breeding habitat need to be understood at the local scale for which larval source management is implemented in order to effectively target larval source interventions. Mapping and monitoring these processes is a well-established practice providing a tractable way forward for developing important malaria management tools.

Tundra landform and vegetation productivity trend maps for the Arctic Coastal Plain of northern Alaska

NASA Astrophysics Data System (ADS)

Lara, Mark J.; Nitze, Ingmar; Grosse, Guido; McGuire, A. David

2018-04-01

Arctic tundra landscapes are composed of a complex mosaic of patterned ground features, varying in soil moisture, vegetation composition, and surface hydrology over small spatial scales (10-100 m). The importance of microtopography and associated geomorphic landforms in influencing ecosystem structure and function is well founded, however, spatial data products describing local to regional scale distribution of patterned ground or polygonal tundra geomorphology are largely unavailable. Thus, our understanding of local impacts on regional scale processes (e.g., carbon dynamics) may be limited. We produced two key spatiotemporal datasets spanning the Arctic Coastal Plain of northern Alaska (~60,000 km2) to evaluate climate-geomorphological controls on arctic tundra productivity change, using (1) a novel 30 m classification of polygonal tundra geomorphology and (2) decadal-trends in surface greenness using the Landsat archive (1999-2014). These datasets can be easily integrated and adapted in an array of local to regional applications such as (1) upscaling plot-level measurements (e.g., carbon/energy fluxes), (2) mapping of soils, vegetation, or permafrost, and/or (3) initializing ecosystem biogeochemistry, hydrology, and/or habitat modeling.

Tundra landform and vegetation productivity trend maps for the Arctic Coastal Plain of northern Alaska.

PubMed

Lara, Mark J; Nitze, Ingmar; Grosse, Guido; McGuire, A David

2018-04-10

Arctic tundra landscapes are composed of a complex mosaic of patterned ground features, varying in soil moisture, vegetation composition, and surface hydrology over small spatial scales (10-100 m). The importance of microtopography and associated geomorphic landforms in influencing ecosystem structure and function is well founded, however, spatial data products describing local to regional scale distribution of patterned ground or polygonal tundra geomorphology are largely unavailable. Thus, our understanding of local impacts on regional scale processes (e.g., carbon dynamics) may be limited. We produced two key spatiotemporal datasets spanning the Arctic Coastal Plain of northern Alaska (~60,000 km 2 ) to evaluate climate-geomorphological controls on arctic tundra productivity change, using (1) a novel 30 m classification of polygonal tundra geomorphology and (2) decadal-trends in surface greenness using the Landsat archive (1999-2014). These datasets can be easily integrated and adapted in an array of local to regional applications such as (1) upscaling plot-level measurements (e.g., carbon/energy fluxes), (2) mapping of soils, vegetation, or permafrost, and/or (3) initializing ecosystem biogeochemistry, hydrology, and/or habitat modeling.

The utilization of ERTS-1 data for the study of the French Atlantic Littoral. [coastal water and geomorphology

NASA Technical Reports Server (NTRS)

Demathieu, P. G.; Verger, F. H.

1974-01-01

The French Atlantic Littoral (FRALIT) program uses ERTS-1 data to study coastal geomorphology and waters. ERTS-1 gives an overall picture of the phenomena for the first time due mainly to channel 4 data, but the other channels also contribute valuable complementary data on superficial waters. These studies have already resulted in accurate maps of the mud transported south-westwards from the mouth of the River Loire.

Publications - PDF 99-24C | Alaska Division of Geological & Geophysical

Science.gov Websites

Alaska's Mineral Industry Reports AKGeology.info Rare Earth Elements WebGeochem Engineering Geology Alaska :63,360 (6.7 M) Keywords Geologic Map; Geology; Geomorphology; Glacial; STATEMAP Project; Slope Instability; Surficial; Surficial Geologic Map; Surficial Geology Top of Page Department of Natural Resources

Delimitation of volcanic edifices for landscape characterization and planning

NASA Astrophysics Data System (ADS)

Melis, Maria Teresa; Mundula, Filippo; Dessì, Francesco; Danila Patta, Elisabetta; Funedda, Antonio; Cioni, Raffaello

2014-05-01

The European Landscape Convention, recently adopted in Italy, indicates specific landforms to be selected as special protected sites. Active and inactive volcanic edifices, defined as the products of evolution of aggradational (lava effusion, pyroclastic deposition, magma intrusion) and degradational processes (erosion, deformation, gravitative phenomena), are one of the specific landforms to be protected. In order to protect these sites, management and planning measures are to be defined and shared with the local communities. In the framework of the Regional Landscape Management Plan of Sardinia (Italy), a detailed study aimed at identifying and delimiting Cenozoic volcanic edifices was performed. The large geological and morphological variability of the volcanic edifices of Sardinia in terms of type, dimension, age, integrity (a measure of the wholeness and intactnes of the volcanic edifice), geology and paleomorphology of the substrate, does not allow the definition of an automatic procedure for extracting the boundaries to delimit the volcanic edifices. In addition, quantitative geomorphological studies in the field of volcanology are confined to specific volcano types, and landscape literature does not suggest any universal criteria for delimiting volcanic edifices, except for the use of the concave breaks in slope at their base (Euillades et al., Computers and Geosciences, 2013). As this simple criterion can be unequivocally applied only in the ideal case of symmetric cones or domes built up on a planar surface, we developed a multidisciplinary methodology based on the integrated analysis of geological, geomorphological and morphometrical data of each edifice. The process of selection and delimitation of the volcanic edifices is the result of the following steps: i) a literature based delimitation of the volcanic edifice; ii) a preliminary delimitation through photo-interpretation and the use of geological criteria; and iii) a final refinement based on the use of DEM-based quantitative elaborations. This final step consists in the construction of maps of the angle of slope and of the surface curvature (concavity, convexity) generated by digital topographic maps in 1:10.000. In addition to this, morphological parameters were combined following the method proposed by Grosse et al. (Geomorphology, 2012) and a new algorithm based on a different combination of the morphometric parameters. The edifice boundaries are manually defined by cross-checking all the available data, and the results are discussed through the use of some examples.

Geomorphology Drives Amphibian Beta Diversity in Atlantic Forest Lowlands of Southeastern Brazil

PubMed Central

Luiz, Amom Mendes; Leão-Pires, Thiago Augusto; Sawaya, Ricardo J.

2016-01-01

Beta diversity patterns are the outcome of multiple processes operating at different scales. Amphibian assemblages seem to be affected by contemporary climate and dispersal-based processes. However, historical processes involved in present patterns of beta diversity remain poorly understood. We assess and disentangle geomorphological, climatic and spatial drivers of amphibian beta diversity in coastal lowlands of the Atlantic Forest, southeastern Brazil. We tested the hypothesis that geomorphological factors are more important in structuring anuran beta diversity than climatic and spatial factors. We obtained species composition via field survey (N = 766 individuals), museum specimens (N = 9,730) and literature records (N = 4,763). Sampling area was divided in four spatially explicit geomorphological units, representing historical predictors. Climatic descriptors were represented by the first two axis of a Principal Component Analysis. Spatial predictors in different spatial scales were described by Moran Eigenvector Maps. Redundancy Analysis was implemented to partition the explained variation of species composition by geomorphological, climatic and spatial predictors. Moreover, spatial autocorrelation analyses were used to test neutral theory predictions. Beta diversity was spatially structured in broader scales. Shared fraction between climatic and geomorphological variables was an important predictor of species composition (13%), as well as broad scale spatial predictors (13%). However, geomorphological variables alone were the most important predictor of beta diversity (42%). Historical factors related to geomorphology must have played a crucial role in structuring amphibian beta diversity. The complex relationships between geomorphological history and climatic gradients generated by the Serra do Mar Precambrian basements were also important. We highlight the importance of combining spatially explicit historical and contemporary predictors for understanding and disentangling major drivers of beta diversity patterns. PMID:27171522

Geomorphology Drives Amphibian Beta Diversity in Atlantic Forest Lowlands of Southeastern Brazil.

PubMed

Luiz, Amom Mendes; Leão-Pires, Thiago Augusto; Sawaya, Ricardo J

2016-01-01

Beta diversity patterns are the outcome of multiple processes operating at different scales. Amphibian assemblages seem to be affected by contemporary climate and dispersal-based processes. However, historical processes involved in present patterns of beta diversity remain poorly understood. We assess and disentangle geomorphological, climatic and spatial drivers of amphibian beta diversity in coastal lowlands of the Atlantic Forest, southeastern Brazil. We tested the hypothesis that geomorphological factors are more important in structuring anuran beta diversity than climatic and spatial factors. We obtained species composition via field survey (N = 766 individuals), museum specimens (N = 9,730) and literature records (N = 4,763). Sampling area was divided in four spatially explicit geomorphological units, representing historical predictors. Climatic descriptors were represented by the first two axis of a Principal Component Analysis. Spatial predictors in different spatial scales were described by Moran Eigenvector Maps. Redundancy Analysis was implemented to partition the explained variation of species composition by geomorphological, climatic and spatial predictors. Moreover, spatial autocorrelation analyses were used to test neutral theory predictions. Beta diversity was spatially structured in broader scales. Shared fraction between climatic and geomorphological variables was an important predictor of species composition (13%), as well as broad scale spatial predictors (13%). However, geomorphological variables alone were the most important predictor of beta diversity (42%). Historical factors related to geomorphology must have played a crucial role in structuring amphibian beta diversity. The complex relationships between geomorphological history and climatic gradients generated by the Serra do Mar Precambrian basements were also important. We highlight the importance of combining spatially explicit historical and contemporary predictors for understanding and disentangling major drivers of beta diversity patterns.

High-resolution Terrestrial Laser Scanning (TLS) on cushion peatlands - a case study from the Peruvian Andes

NASA Astrophysics Data System (ADS)

Forbriger, M.; Höfle, B.; Siart, C.; Schittek, K.; Bubenzer, O.

2012-04-01

So-called cushion peatlands located in the high mountain areas of the Peruvian Andes are unique ecotopes, which are of major importance for both palaeoenvironmental reconstructions and permanent water supply of the valley oases in the presently hyperarid Peruvian desert. In this context, a case study was performed on the Cerro Llamoca peatland (southern Peru, province Lucanas, 14° S) in the uppermost reaches of the Rió Grande catchment area (4000-4450 m a.s.l.) within the framework of the BMBF-funded project 'Andean Transect - Climate Sensitivity of pre-Columbian Man-Environment-Systems' and serves as a basis for a long-term, multitemporal observation study. As small-scale geomorphologic investigations require high-resolution elevation data, which is still not available for this remote study site, and local microrelief is characterised by features not visible from aerial view (e.g. channel cuttings within the peatland), terrestrial laser scanning (TLS) was applied. Data acquisition was carried out with one of the latest 'time-of-flight'-scanners (Riegl VZ-400). A total of 46 positions was recorded to capture the whole area of interest leading to more 370 million single laser points within an area of approximately 1,8 km2. Registration of scan positions was performed by means of GPS measurements, coarse registration and the iterative closest point (ICP) algorithm provided by the plugin Multi-Station Adjustment within the RiSCAN PRO software (Riegl). The large amount of output data required the use of special LiDAR software for further processing and digital elevation raster generation (OPALS software). The defined target raster resolution was set to values between 0.1 and 2 m depending on the average point density. It is important to have access to the original point cloud including additional laser point attributes (e.g. signal amplitude and echo width) for digital terrain model generation (i.e. terrain point filtering) and geomorphologic mapping by means of segmentation and object-based classification. Furthermore, multitemporal investigation of the study area requires co-registration of the datasets of the different epochs to each other, which is best performed using the original point cloud. This guarantees high accuracy of elevation change estimation and, thus, volume change assessment. Geomorphologic microscale features can be analyzed in, by now, inaccessible details and therefore also short term events with only little impact can be investigated. The outcomes demonstrate the great suitability of terrestrial laser scanning for fast and high-precision mapping, particularly in isolated terrains at high altitudes like the Peruvian Altiplano. Future investigations will focus on data fusion of surface and subsurface data derived from geophysical measurements. In combination with vibra coring, chronometric dating and geochemical analysis palaeoenvironmental 3D reconstructions over time are possible. With regard to recent water storage capacity, new approximations can be carried out. Additionally, the determination of erosion and degradation rates will be possible at high resolutions.

Towards Automation in Landcover Mapping from LiDAR Data in Alpine Environment

NASA Astrophysics Data System (ADS)

Dorninger, Peter; Briese, Christian; Nothegger, Clemens; Klauser, Armin

2010-05-01

Digital terrain models derived from airborne LiDAR (often referred to as airborne laser scanning) are commonly used for various applications in geomorphology. The ongoing development in sensor technology makes flight campaigns with some 10 points per square meter economically feasible for large areas. Simultaneously, the achievable accuracy of the originally acquired points as well as those of the derived products increases due to improved measurement techniques. Additionally, full-waveform (FWF) laser scanning systems record the time-dependent strength of the backscattered signal. This allows for the determination of numerous points (i.e. echoes) for one emitted laser beam hitting multiple targets within its footprint. Practically, about five echoes may be determined from the digitized signal form. Furthermore, additional attributes can be determined for each echo. These are, for example, a reflectivity measure (amplitude), the widening of the echo (echo width), or the sequence of the echoes of a single shot. By considering the polar measurement range and atmospheric conditions, a physical calibration of such measurements is possible. The application of FWF information to increase the accuracy and the reliability of digital terrain models especially in areas with dense vegetation was shown by Doneus & Briese (2006). However, these additional attributes are rarely used for object or landcover classification. This is still the domain of automated image interpretation (e.g. Zebedin et al., 2006). Nevertheless, image interpretation has well known deficiencies in areas with vegetation or if shadows occur. Therefore, we tested a hybrid approach which uses conventional first echo / last echo (FE/LE) airborne laser scanning data (first and last pulse) and an RGB-orthophoto. The testing site is located in an alpine area in Tyrol, Austria. For the classification, topographic models, a slope map, a local roughness measure and a penetration ratio were determined from the laser scanning data. Additionally, a vegetation index was derived from the orthophoto. Using a supervised classification approach based on well known testing sites, the following classes could be determined: forest, dwarf-pines, grass land, debris, and bare rock. After a generalization step, we compared the results to two existing topographic landcover maps showing high correlation. However, the method showed several shortcomings in shadowed areas in the orthophoto. Furthermore, a separation of debris and bare rock was only possibly by a slope threshold. To overcome these problems, we investigated another testing site, situated in the alpine region of Lower Austria, Austria. The data was acquired by a Riegl LMS-Q560 FWF laser scanner. In this case we did not use an orthophoto. Instead we considered additional parameters derived from the FWF data. These were a distance corrected amplitude and the pulse width, and, especially in regions with high vegetation, multiple echoes were available. Furthermore, we derived highly robust local tangential planes for each point (Nothegger & Dorninger, 2008). Due to those tangential planes being computed in three-dimensions, the computation of the slope angles, especially in steep regions, becomes more reliable. Additionally, quality parameters provided by the plane estimation were considered for the classification. For example, the local roughness measure indicates vegetation. So it could be demonstrated that point based classification of LiDAR data allows for landcover classification in alpine areas. To achieve reliable results from FE/LE laser scanning data, the integration of image data was necessary. However, this introduced typical shortcomings of geomorphological interpretation in vegetation and shadowed areas. The use of FWF laser scanning allows overcoming these shortcomings and increasing the automation of reliable landcover mapping including the characteristics of alpine geomorphic features. References: C. Nothegger, P. Dorninger: "3D Filtering of High-Resolution Terrestrial Laser Scanner Point Clouds for Cultural Heritage Documentation"; Photogrammetrie, Fernerkundung, Geoinformation, 1 (2009), 53 - 63. M. Doneus, C. Briese: "Digital Terrain Modelling For Archaeological Interpretation Within Forested Areas Using Full-Waveform Laserscanning", The 7Th International Symposium on Virtual Reality, Archaeology and Cultural Heritage Vast (2006) L. Zebedin, A. Klaus, B. Gruber-Geymayer, K. Karner: "Towards 3D map generation from digital aerial images", ISPRS Journal of Photogrammetry & Remote Sensing, Vol. 60, 413-427 (2006).

Global Drainage Patterns to Modern Terrestrial Sedimentary Basins and its Influence on Large River Systems

NASA Astrophysics Data System (ADS)

Nyberg, B.; Helland-Hansen, W.

2017-12-01

Long-term preservation of alluvial sediments is dependent on the hydrological processes that deposit sediments solely within an area that has available accomodation space and net subsidence know as a sedimentary basin. An understanding of the river processes contributing to terrestrial sedimentary basins is essential to fundamentally constrain and quantify controls on the modern terrestrial sink. Furthermore, the terrestrial source to sink controls place constraints on the entire coastal, shelf and deep marine sediment routing systems. In addition, the geographical importance of modern terrestrial sedimentary basins for agriculture and human settlements has resulted in significant upstream anthropogenic catchment modification for irrigation and energy needs. Yet to our knowledge, a global catchment model depicting the drainage patterns to modern terrestrial sedimentary basins has previously not been established that may be used to address these challenging issues. Here we present a new database of 180,737 global catchments that show the surface drainage patterns to modern terrestrial sedimentary basins. This is achieved by using high resolution river networks derived from digital elevation models in relation to newly acquired maps on global modern sedimentary basins to identify terrestrial sinks. The results show that active tectonic regimes are typically characterized by larger terrestrial sedimentary basins, numerous smaller source catchments and a high source to sink relief ratio. To the contrary passive margins drain catchments to smaller terrestrial sedimentary basins, are composed of fewer source catchments that are relatively larger and a lower source to sink relief ratio. The different geomorphological characteristics of source catchments by tectonic setting influence the spatial and temporal patterns of fluvial architecture within sedimentary basins and the anthropogenic methods of exploiting those rivers. The new digital database resource is aimed to help the geoscientific community to contribute further to our quantitative understanding of source-to-sink systems and its allogenic and autogenic controls, geomorphological characteristics, terrestrial sediment transit times and the anthropogenic impact on those systems.

Stable isotopes and Digital Elevation Models to study nutrient inputs in high-Arctic lakes

NASA Astrophysics Data System (ADS)

Calizza, Edoardo; Rossi, David; Costantini, Maria Letizia; Careddu, Giulio; Rossi, Loreto

2016-04-01

Ice cover, run-off from the watershed, aquatic and terrestrial primary productivity, guano deposition from birds are key factors controlling nutrient and organic matter inputs in high-Arctic lakes. All these factors are expected to be significantly affected by climate change. Quantifying these controls is a key baseline step to understand what combination of factors subtends the biological productivity in Arctic lakes and will drive their ecological response to environmental change. Basing on Digital Elevation Models, drainage maps, and C and N elemental content and stable isotope analysis in sediments, aquatic vegetation and a dominant macroinvertebrate species (Lepidurus arcticus Pallas 1973) belonging to Tvillingvatnet, Storvatnet and Kolhamna, three lakes located in North Spitsbergen (Svalbard), we propose an integrated approach for the analysis of (i) nutrient and organic matter inputs in lakes; (ii) the role of catchment hydro-geomorphology in determining inter-lake differences in the isotopic composition of sediments; (iii) effects of diverse nutrient inputs on the isotopic niche of Lepidurus arcticus. Given its high run-off and large catchment, organic deposits in Tvillingvatnet where dominated by terrestrial inputs, whereas inputs were mainly of aquatic origin in Storvatnet, a lowland lake with low potential run-off. In Kolhamna, organic deposits seem to be dominated by inputs from birds, which actually colonise the area. Isotopic signatures were similar between samples within each lake, representing precise tracers for studies on the effect of climate change on biogeochemical cycles in lakes. The isotopic niche of L. aricticus reflected differences in sediments between lakes, suggesting a bottom-up effect of hydro-geomorphology characterizing each lake on nutrients assimilated by this species. The presented approach proven to be an effective research pathway for the identification of factors subtending to nutrient and organic matter inputs and transfer within each water body, as well as for the modelling of expected changes in nutrient content associated to changes in isotopic composition of sediments. Key words: nitrogen; carbon, sediment; biogeochemical cycle; climate change; hydro-ecology; isotopic niche; Svalbard

Comparing morphologies of drainage basins on Mars and Earth using integral-geometry and neural maps

NASA Technical Reports Server (NTRS)

Stepinski, T. F.; Coradetti, S.

2004-01-01

We compare morphologies of drainage basins on Mars and Earth in order to confine the formation process of Martian valley networks. Basins on both planets are computationally extracted from digital topography. Integral-geometry methods are used to represent each basin by a circularity function that encapsulates its internal structure. The shape of such a function is an indicator of the style of fluvial erosion. We use the self-organizing map technique to construct a similarity graph for all basins. The graph reveals systematic differences between morphologies of basins on the two planets. This dichotomy indicates that terrestrial and Martian surfaces were eroded differently. We argue that morphologies of Martian basins are incompatible with runoff from sustained, homogeneous rainfall. Fluvial environments compatible with observed morphologies are discussed. We also construct a similarity graph based on the comparison of basins hypsometric curves to demonstrate that hypsometry is incapable of discriminating between terrestrial and Martian basins. INDEX TERMS: 1824 Hydrology: Geomorphology (1625); 1886 Hydrology: Weathering (1625); 5415 Planetology: Solid Surface Planets: Erosion and weathering; 6225 Planetology: Solar System Objects Mars. Citation: Stepinski, T. F., and S. Coradetti (2004), Comparing morphologies of drainage basins on Mars and Earth using integral-ge

Geomorphology, acoustic backscatter, and processes in Santa Monica Bay from multibeam mapping.

PubMed

Gardner, James V; Dartnell, Peter; Mayer, Larry A; Hughes Clarke, John E

2003-01-01

Santa Monica Bay was mapped in 1996 using a high-resolution multibeam system, providing the first substantial update of the submarine geomorphology since the initial compilation by Shepard and Emery [(1941) Geol. Soc. Amer. Spec. Paper 31]. The multibeam mapping generated not only high-resolution bathymetry, but also coregistered, calibrated acoustic backscatter at 95 kHz. The geomorphology has been subdivided into six provinces; shelf, marginal plateau, submarine canyon, basin slope, apron, and basin. The dimensions, gradients, and backscatter characteristics of each province is described and related to a combination of tectonics, climate, sea level, and sediment supply. Fluctuations of eustatic sea level have had a profound effect on the area; by periodically eroding the surface of Santa Monica plateau, extending the mouth of the Los Angeles River to various locations along the shelf break, and by connecting submarine canyons to rivers. A wetter glacial climate undoubtedly generated more sediment to the rivers that then transported the increased sediment load to the low-stand coastline and canyon heads. The trends of Santa Monica Canyon and several bathymetric highs suggest a complex tectonic stress field that has controlled the various segments. There is no geomorphic evidence to suggest Redondo Canyon is fault controlled. The San Pedro fault can be extended more than 30 km to the northwest by the alignment of a series of bathymetric highs and abrupt changes in direction of channel thalwegs.

Publications - RI 2000-1A | Alaska Division of Geological & Geophysical

Science.gov Websites

; Folding; Formations; Fossils; Generalized; Geologic; Geologic Map; Geology; Geomorphology; Glacial ; Silt; Structure; Surficial; Surficial Geology; Tectonics; Tertiary; Thaw Lakes; Trace Fossils

Preservation potential of subtle glacial landforms based on detailed mapping of recently exposed proglacial areas: application of unmanned aerial vehicle (UAV) and structure-from-motion (SfM)

NASA Astrophysics Data System (ADS)

Ewertowski, Marek; Evans, David; Roberts, David; Tomczyk, Aleksandra; Ewertowski, Wojciech

2016-04-01

Ongoing glacier retreat results in the continuous exposure of proglacial areas. Such areas contain invaluable information about glacial process-form relationships manifest in specific landform assemblages. However, preservation potential of freshly exposed glacial landforms is very low, as proglacial terrains are one of the most dynamic parts of the landscape. Therefore, rapid mapping and geomorphological characterisation of such areas is important from a glaciological and geomorphological point of view for proper understanding and reconstruction of glacier-landform dynamics and chronology of glacial events. Annual patterns of recession and relatively small areas exposed every year, mean that the performing of regular aerial or satellite survey is expensive and therefore impractical. Recent advances in technology enables the development of low-cost alternatives for traditional aerial surveys. Small unmanned aerial vehicles (UAV) can be used to acquire high-resolution (several cm) low-altitude photographs. The UAV-based photographs can be subsequently processed through the structure-from-motion process to generate detailed orthophotomaps and digital elevation models. In this study we present case studies from the forelands of various glaciers on Iceland and Svalbard representing different types of proglacial landscapes: Fláajökull (annual push moraines); Hofellsjökul (bedrock bedforms and push moraines); Fjallsjökull (marginal drainage network); Rieperbreen (crevasse squeeze ridges and longitudinal debris stripes); Ayerbreen (transverse debris ridges); Foxfonna (longitudinal debris stripes);Hørbyebreen (geometric ridge network); Nordenskiöldbreen (fluted till surface); Ebbabreen (controlled moraine complex). UAV campaigns were conducted using a low-cost quadcopter platform. Resultant orthophotos and DEMs enabled mapping and assessment of recent glacial landscape development in different types of glacial landsystems. Results of our study indicate that preservation potential of geometric ridge networks and debris stripes produced by polythermal glaciers on Svalbard is very low (< 5 years), whereas subtle landforms indicative for temperate conditions: annual push moraines (Iceland)and flutings (Iceland and Svalbard) - can survive decades without being seriously modified.

Development of Waterfall Cliff Face: An Implication from Multitemporal High-definition Topographic Data

NASA Astrophysics Data System (ADS)

Hayakawa, Y. S.; Obanawa, H.

2015-12-01

Bedrock knickpoints (waterfalls) often act as erosional front in bedrock rivers, whose geomorphological processes are various. In waterfalls with vertical cliffs, both fluvial erosion and mass movement are feasible to form the landscape. Although morphological changes of such steep cliffs are sometimes visually observed, quantitative and precise measurements of their spatiotemporal distribution have been limited due to poor accessibility to such cliffs. For the clarification of geomorphological processes in such cliffs, multi-temporal mapping of the cliff face at a high resolution can be advantaged by short-range remote sensing approaches. Here we carry out multi-temporal terrestrial laser scanning (TLS), as well as structure-from-motion multi-view stereo (SfM-MVS) photogrammetry based on unmanned aerial system (UAS) for accurate topographic mapping of cliffs around a waterfall. The study site is Kegon Falls in central Japan, having a vertical drop of surface water from top of its overhanging cliff and groundwater outflows from its lower portions. The bedrock consists of alternate layers of jointed andesite lava and conglomerates. The latest major rockfall in 1986 caused approximately 8-m recession of the waterfall lip. Three-dimensional changes of the rock surface were detected by multi-temporal measurements by TLS over years, showing the portions of small rockfalls and surface lowering in the bedrock. Erosion was frequently observed in relatively weak the conglomerates layer, whereas small rockfalls were often found in the andesite layers. Wider areas of the waterfall and cliff were also measured by UAS-based SfM-MVS photogrammetry, improving the mapping quality of the cliff morphology. Point clouds are also projected on a vertical plane to generate a digital elevation model (DEM), and cross-sectional profiles extracted from the DEM indicate the presence of a distinct, 5-10-m deep depression in the cliff face. This appears to have been formed by freeze-thaw and/or wet-dry weathering following the recession in 1986. The long-term development of the waterfall cliff face is then discussed comprising various processes of rockfalls, water pressure and weathering.

Automated identification of stream-channel geomorphic features from high‑resolution digital elevation models in West Tennessee watersheds

USGS Publications Warehouse

Cartwright, Jennifer M.; Diehl, Timothy H.

2017-01-17

High-resolution digital elevation models (DEMs) derived from light detection and ranging (lidar) enable investigations of stream-channel geomorphology with much greater precision than previously possible. The U.S. Geological Survey has developed the DEM Geomorphology Toolbox, containing seven tools to automate the identification of sites of geomorphic instability that may represent sediment sources and sinks in stream-channel networks. These tools can be used to modify input DEMs on the basis of known locations of stormwater infrastructure, derive flow networks at user-specified resolutions, and identify possible sites of geomorphic instability including steep banks, abrupt changes in channel slope, or areas of rough terrain. Field verification of tool outputs identified several tool limitations but also demonstrated their overall usefulness in highlighting likely sediment sources and sinks within channel networks. In particular, spatial clusters of outputs from multiple tools can be used to prioritize field efforts to assess and restore eroding stream reaches.

Identification of large geomorphological anomalies based on 2D discrete wavelet transform

NASA Astrophysics Data System (ADS)

Doglioni, A.; Simeone, V.

2012-04-01

The identification and analysis based on quantitative evidences of large geomorphological anomalies is an important stage for the study of large landslides. Numerical geomorphic analyses represent an interesting approach to this kind of studies, allowing for a detailed and pretty accurate identification of hidden topographic anomalies that may be related to large landslides. Here a geomorphic numerical analyses of the Digital Terrain Model (DTM) is presented. The introduced approach is based on 2D discrete wavelet transform (Antoine et al., 2003; Bruun and Nilsen, 2003, Booth et al., 2009). The 2D wavelet decomposition of the DTM, and in particular the analysis of the detail coefficients of the wavelet transform can provide evidences of anomalies or singularities, i.e. discontinuities of the land surface. These discontinuities are not very evident from the DTM as it is, while 2D wavelet transform allows for grid-based analysis of DTM and for mapping the decomposition. In fact, the grid-based DTM can be assumed as a matrix, where a discrete wavelet transform (Daubechies, 1992) is performed columnwise and linewise, which basically represent horizontal and vertical directions. The outcomes of this analysis are low-frequency approximation coefficients and high-frequency detail coefficients. Detail coefficients are analyzed, since their variations are associated to discontinuities of the DTM. Detailed coefficients are estimated assuming to perform 2D wavelet transform both for the horizontal direction (east-west) and for the vertical direction (north-south). Detail coefficients are then mapped for both the cases, thus allowing to visualize and quantify potential anomalies of the land surface. Moreover, wavelet decomposition can be pushed to further levels, assuming a higher scale number of the transform. This may potentially return further interesting results, in terms of identification of the anomalies of land surface. In this kind of approach, the choice of a proper mother wavelet function is a tricky point, since it conditions the analysis and then their outcomes. Therefore multiple levels as well as multiple wavelet analyses are guessed. Here the introduced approach is applied to some interesting cases study of south Italy, in particular for the identification of large anomalies associated to large landslides at the transition between Apennine chain domain and the foredeep domain. In particular low Biferno valley and Fortore valley are here analyzed. Finally, the wavelet transforms are performed on multiple levels, thus trying to address the problem of which is the level extent for an accurate analysis fit to a specific problem. Antoine J.P., Carrette P., Murenzi R., and Piette B., (2003), Image analysis with two-dimensional continuous wavelet transform, Signal Processing, 31(3), pp. 241-272, doi:10.1016/0165-1684(93)90085-O. Booth A.M., Roering J.J., and Taylor Perron J., (2009), Automated landslide mapping using spectral analysis and high-resolution topographic data: Puget Sound lowlands, Washington, and Portland Hills, Oregon, Geomorphology, 109(3-4), pp. 132-147, doi:10.1016/j.geomorph.2009.02.027. Bruun B.T., and Nilsen S., (2003), Wavelet representation of large digital terrain models, Computers and Geoscience, 29(6), pp. 695-703, doi:10.1016/S0098-3004(03)00015-3. Daubechies, I. (1992), Ten lectures on wavelets, SIAM.

Distribution of late Pleistocene ice-rich syngenetic permafrost of the Yedoma Suite in east and central Siberia, Russia

USGS Publications Warehouse

Grosse, Guido; Robinson, Joel E.; Bryant, Robin; Taylor, Maxwell D.; Harper, William; DeMasi, Amy; Kyker-Snowman, Emily; Veremeeva, Alexandra; Schirrmeister, Lutz; Harden, Jennifer

2013-01-01

This digital database is the product of collaboration between the U.S. Geological Survey, the Geophysical Institute at the University of Alaska, Fairbanks; the Los Altos Hills Foothill College GeoSpatial Technology Certificate Program; the Alfred Wegener Institute for Polar and Marine Research, Potsdam, Germany; and the Institute of Physical Chemical and Biological Problems in Soil Science of the Russian Academy of Sciences. The primary goal for creating this digital database is to enhance current estimates of soil organic carbon stored in deep permafrost, in particular the late Pleistocene syngenetic ice-rich permafrost deposits of the Yedoma Suite. Previous studies estimated that Yedoma deposits cover about 1 million square kilometers of a large region in central and eastern Siberia, but these estimates generally are based on maps with scales smaller than 1:10,000,000. Taking into account this large area, it was estimated that Yedoma may store as much as 500 petagrams of soil organic carbon, a large part of which is vulnerable to thaw and mobilization from thermokarst and erosion. To refine assessments of the spatial distribution of Yedoma deposits, we digitized 11 Russian Quaternary geologic maps. Our study focused on extracting geologic units interpreted by us as late Pleistocene ice-rich syngenetic Yedoma deposits based on lithology, ground ice conditions, stratigraphy, and geomorphological and spatial association. These Yedoma units then were merged into a single data layer across map tiles. The spatial database provides a useful update of the spatial distribution of this deposit for an approximately 2.32 million square kilometers land area in Siberia that will (1) serve as a core database for future refinements of Yedoma distribution in additional regions, and (2) provide a starting point to revise the size of deep but thaw-vulnerable permafrost carbon pools in the Arctic based on surface geology and the distribution of cryolithofacies types at high spatial resolution. However, we recognize that the extent of Yedoma deposits presented in this database is not complete for a global assessment, because Yedoma deposits also occur in the Taymyr lowlands and Chukotka, and in parts of Alaska and northwestern Canada.

Assessment of geomorphological and hydrological changes produced by Pleistocene glaciations in a Patagonian basin

NASA Astrophysics Data System (ADS)

Scordo, Facundo; Seitz, Carina; Melo, Walter D.; Piccolo, M. Cintia; Perillo, Gerardo M. E.

2018-04-01

This work aims to assess how Pleistocene glaciations modeled the landscape in the upper Senguer River basin and its relationship to current watershed features (drainage surface and fluvial hydrological regime). During the Pleistocene six glacial lobes developed in the upper basin of the Senguer River localized east of the Andean range in southern Argentinean Patagonia between 43° 36' - 46° 27‧ S. To describe the topography and hydrology, map the geomorphology, and propose an evolution of the study area during the Pleistocene we employed multitemporal Landsat images, national geological sheets and a mosaic of the digital elevation model (Shuttle Radar Topography Mission) along with fieldwork. The main conclusion is that until the Middle Pleistocene, the drainage divide of the Senguer River basin was located to the west of its current limits and its rivers drained the meltwater of the glaciers during interglacial periods. However, processes of drainage inversion and drainage surface reduction occurred in the headwater of most rivers of the basin during the Late Pleistocene. Those processes were favored by a relative shorter glacial extension during LGM and the dam effect produced by the moraines of the Post GPG I and III glaciations. Thus, since the Late Pleistocene, the headwaters of several rivers in the basin have been reduced, and the moraines corresponding to the Middle Pleistocene glaciations currently divide the watersheds that drain towards the Senguer River from those that flow west towards the Pacific Ocean.

Landscapes of human evolution: models and methods of tectonic geomorphology and the reconstruction of hominin landscapes.

PubMed

Bailey, Geoffrey N; Reynolds, Sally C; King, Geoffrey C P

2011-03-01

This paper examines the relationship between complex and tectonically active landscapes and patterns of human evolution. We show how active tectonics can produce dynamic landscapes with geomorphological and topographic features that may be critical to long-term patterns of hominin land use, but which are not typically addressed in landscape reconstructions based on existing geological and paleoenvironmental principles. We describe methods of representing topography at a range of scales using measures of roughness based on digital elevation data, and combine the resulting maps with satellite imagery and ground observations to reconstruct features of the wider landscape as they existed at the time of hominin occupation and activity. We apply these methods to sites in South Africa, where relatively stable topography facilitates reconstruction. We demonstrate the presence of previously unrecognized tectonic effects and their implications for the interpretation of hominin habitats and land use. In parts of the East African Rift, reconstruction is more difficult because of dramatic changes since the time of hominin occupation, while fossils are often found in places where activity has now almost ceased. However, we show that original, dynamic landscape features can be assessed by analogy with parts of the Rift that are currently active and indicate how this approach can complement other sources of information to add new insights and pose new questions for future investigation of hominin land use and habitats. Copyright © 2010 Elsevier Ltd. All rights reserved.

Geomorphological evolution of volcanic fluvial channels: Eighteen years of morphological monitoring of the upper strect of the Tenenepanco Gorge, Popocatépetl volcano, Mexico

NASA Astrophysics Data System (ADS)

Tanarro, Luis Miguel; Juan Zamorano, Jose; Andres, Nuria; Palacios, David

2015-04-01

During volcanic eruptions a significant volume of material accumulates on the slopes and pre-existing gorges of the stratovolcanoes. This abundance of loose and unconsolidated material is very likely to be mobilized by rapid flows or lahars generated by sudden heavy rain or melting snow and ice. Thus, volcanic gorges are affected by complex cycles of incision, filling and widening, altering the equilibrium of river systems due to the major changes that lahars cause in channel morphology. These geomorphological dynamics characterize the gorges located on the north flank of the Popocatépetl volcano (19°02' N, 98°62' W, 5424 m). This volcano, located in the centre of the Trans-Mexican Volcanic Belt, began its most recent eruptive period in December 1994, when a glacier partially covered the northern slope. Since then, the interaction of volcanic and glacier activity triggered the formation of lahars in the gorges, causing significant morphological changes in the channel (especially in April 1995, July 1997 and January 2001). The most recent major eruption at Popocatépetl took place on 19 July 2003, and since then a series of smaller eruptions has reduced the glacier to near extinction. The aim of this study is to assess the morphological response of the Tenenepanco channel over an 18-year period, from 1995-2013, where two main scenarios can be observed: a) the period from 1995 to 2001 of volcanic activity and glacier retreat with the formation of flows and b) the period from 2002 to 2013 of relative volcanic calm, the almost complete extinction of the glacier, and the formation of secondary lahars associated with heavy rainfall. Monitoring of the gorge has consisted in the elaboration of 14 geomorphological maps during field studies (November 14, 1995, December 5, 1997, February 7, 1998, October 6, 2001, November 14, 1995, December 5, 1997, February 7, 1998, October 6, 2001, Julio 16, 2002, February 11, 2004, September 8, 2004, February 5, 2006, November 2, 2008, February 5, 2008, November 5, 2009, November 5, 2010, November 9, 2011, November 6, 2013). An additional map (May-1989) was made based on photo-interpretation of aerial photographs taken during that period. A set of 13 morphological units were recognized in each of the maps. Subsequently, the maps were georeferenced using a 2010 orthophoto and the image of Google Earth from 2013. In a second step the 15 maps were digitized and the topology created in a CAD environment (Bentley Microstation V8i). Finally a spatial analysis was carried out in a GIS (ESRI ArcMap 10) in order to study the morphological variations of the channel gorge. The preliminary results show that during the initial period (1995-2001) channel evolution is more variable, with episodes in which the bottom of the gorge is eroded with multiple channels alternating with others where there is only a single channel. These moments presumably coincide with volcanic activity which provides abundant material that fills the smaller gullies and concentrates the lahars in a single channel. However, the secondary flows in the 2002-2013 period tend to merge into one wide channel that drops in depth, creating pseudo-terraces. Research funded by Cryocrisis project (CGL2012-35858), Government of Spain

Stream gradient Hotspot and Cluster Analysis (SL-HCA) for improving the longitudinal profiles metrics

NASA Astrophysics Data System (ADS)

Troiani, Francesco; Piacentini, Daniela; Seta Marta, Della

2016-04-01

Many researches successfully focused on stream longitudinal profiles analysis through Stream Length-gradient (SL) index for detecting, at different spatial scales, either tectonic structures or hillslope processes. The analysis and interpretation of spatial variability of SL values, both at a regional and local scale, is often complicated due to the concomitance of different factors generating SL anomalies, including the bedrock composition. The creation of lithologically-filtered SL maps is often problematic in areas where homogeneously surveyed geological maps, with a sufficient resolution are unavailable. Moreover, both the SL map classification and the unbiased anomaly detection are rather difficult. For instance, which is the best threshold to define the anomalous SL values? Further, is there a minimum along-channel extent of anomalous SL values for objectively defining over-steeped segments on long-profiles? This research investigates the relevance and potential of a new approach based on Hotspot and Cluster Analysis of SL values (SL-HCA) for detecting knickzones on long-profiles at a regional scale and for fine-tuning the interpretation of their geological-geomorphological meaning. We developed this procedure within a 2800 km2-wide area located in the mountainous sector of the Northern Apennines of Italy. The Getis-Ord Gi∗ statistic is applied for the SL-HCA approach. The value of SL, calculated starting from a 5x5 m Digital Elevation Model, is used as weighting factor and the Gi∗ index is calculated for each 50 m-long channel segment for the whole fluvial system. The outcomes indicate that high positive Gi∗ values imply the clustering of SL anomalies, thus the occurrence of knickzones on the stream long-profiles. Results show that high and very high Gi* values (i.e. values beyond two standard deviations from the mean) correlate well with the principal knickzones detected with existent lithologically-filtered SL maps. Field checks and remote sensing analysis conducted on 52 clusters of high and very high Gi* values indicate that mass movement of slope material represents the dominant process producing over-steeped long-profiles along connected streams, whereas the litho-structure accounts for the main anomalies along disconnected steams. Tectonic structures generally provide to the largest clusters. Our results demonstrate that SL-HCA maps have the same potential of lithologically-filtered SL maps for detecting knickzones due to hillslope processes and/or tectonic structures. The reduced-complexity model derived from SL-HCA approach highly improve the readability of the morphometric outcomes, thus the interpretation at a regional scale of the geological-geomorphological meaning of over-steeped segments on long-profiles. SL-HCA maps are useful to investigate and better interpret knickzones within regions poorly covered by geological data and where field surveys are difficult to be performed.

Tundra landform and vegetation productivity trend maps for the Arctic Coastal Plain of northern Alaska

PubMed Central

Lara, Mark J.; Nitze, Ingmar; Grosse, Guido; McGuire, A. David

2018-01-01

Arctic tundra landscapes are composed of a complex mosaic of patterned ground features, varying in soil moisture, vegetation composition, and surface hydrology over small spatial scales (10–100 m). The importance of microtopography and associated geomorphic landforms in influencing ecosystem structure and function is well founded, however, spatial data products describing local to regional scale distribution of patterned ground or polygonal tundra geomorphology are largely unavailable. Thus, our understanding of local impacts on regional scale processes (e.g., carbon dynamics) may be limited. We produced two key spatiotemporal datasets spanning the Arctic Coastal Plain of northern Alaska (~60,000 km2) to evaluate climate-geomorphological controls on arctic tundra productivity change, using (1) a novel 30 m classification of polygonal tundra geomorphology and (2) decadal-trends in surface greenness using the Landsat archive (1999–2014). These datasets can be easily integrated and adapted in an array of local to regional applications such as (1) upscaling plot-level measurements (e.g., carbon/energy fluxes), (2) mapping of soils, vegetation, or permafrost, and/or (3) initializing ecosystem biogeochemistry, hydrology, and/or habitat modeling. PMID:29633984

Tundra landform and vegetation productivity trend maps for the Arctic Coastal Plain of northern Alaska

USGS Publications Warehouse

Lara, Mark J.; Nitze, Ingmar; Grosse, Guido; McGuire, A. David

2018-01-01

Arctic tundra landscapes are composed of a complex mosaic of patterned ground features, varying in soil moisture, vegetation composition, and surface hydrology over small spatial scales (10–100 m). The importance of microtopography and associated geomorphic landforms in influencing ecosystem structure and function is well founded, however, spatial data products describing local to regional scale distribution of patterned ground or polygonal tundra geomorphology are largely unavailable. Thus, our understanding of local impacts on regional scale processes (e.g., carbon dynamics) may be limited. We produced two key spatiotemporal datasets spanning the Arctic Coastal Plain of northern Alaska (~60,000 km2) to evaluate climate-geomorphological controls on arctic tundra productivity change, using (1) a novel 30 m classification of polygonal tundra geomorphology and (2) decadal-trends in surface greenness using the Landsat archive (1999–2014). These datasets can be easily integrated and adapted in an array of local to regional applications such as (1) upscaling plot-level measurements (e.g., carbon/energy fluxes), (2) mapping of soils, vegetation, or permafrost, and/or (3) initializing ecosystem biogeochemistry, hydrology, and/or habitat modeling.

A millennial-scale record of tidewater glacier advance and retreat, SW Greenland.

NASA Astrophysics Data System (ADS)

Pearce, Danni; Mair, Doug; Rea, Brice; Schofield, Ed; Lea, James; Barr, Iestyn; Kamenos, Nick; Schoenrock, Kate

2017-04-01

Tidewater glaciers (TWGs) exert a major control on the short- and long-term mass balance of the Greenland Ice Sheet (GrIS) and have experienced widespread retreat over the last century. However, in many cases inferences on their dynamics, prior to this, are poorly constrained due to a lack of observations and paucity of mapped or mappable deglacial geomorphology. Especially lacking is evidence associated with TWG advance during the Little Ice Age (LIA, AD c. 1300 to 1850). Such data are crucial for numerical model calibration and validation in order to more confidently forward model ice sheet dynamics and projection future sea-level rise. Therefore, empirical data constraints from the palaeo-record, that span such timescales (decadal to millennial), are essential. Kangiata Nunaata Sermia (KNS) is the most dynamic TWG in SW Greenland, located c. 100 km inland from Nuuk, at the head of Godthabsfjord. KNS has received considerable research attention over the last decade but glacial geomorphological and numerical dating investigations have been limited. However, the adjacent topography and geomorphology presents a unique opportunity to reconstruct the advance and retreat dynamics over the LIA. We present detailed glacial geomorphological mapping for KNS, which followed a morphostratigraphic approach, using a combination of aerial photos, Landsat, a DEM and field mapping. This identified a three landsystems, which are associated with the LIA, pre-LIA and neoglacial. From the mapping inferences on rapid changes in meltwater routing have been inferred. When KNS reached its LIA maximum (c. 1761), the calving front was c. >22 km further along the fjord than present and a number of ice-dammed lakes were formed. We present new 14C dating from peat underlying lake sediments associated with an ice-dammed lake and buried palaeosols resulting from meltwater re-routing over topographic spillways. The ages support an early and rapid LIA advance phase, with advance rates being comparable with published data from Columbia Glacier during the LIA (Nick et al., 2007, JGR). This centennial to millennial timescale record of TWG dynamics, will provide a dataset for numerical model calibration and validation linking calving glacier dynamics to atmospheric and oceanic forcing.

Coastal flooding hazard related to storms and coastal evolution in Valdelagrana spit (Cadiz Bay Natural Park, SW Spain)

NASA Astrophysics Data System (ADS)

Benavente, J.; Del Río, L.; Gracia, F. J.; Martínez-del-Pozo, J. A.

2006-06-01

Mapping of coastal inundation hazard related to storms requires the combination of multiple sources of information regarding meteorological, morphological and dynamic characteristics of both the area at risk and the studied phenomena. Variables such as beach slope, storm wave height or wind speed have traditionally been used, but detailed geomorphological features of the area as well as long-term shoreline evolution trends must also be taken into account in order to achieve more realistic results. This work presents an evaluation of storm flooding hazard in Valdelagrana spit and marshes (SW Spain), considering two types of storm that are characteristic of the area: a modal storm with 1 year of recurrence interval (maximum wave height of 3.3 m), and an extreme storm with 6-10 years of recurrence interval (maximum wave height of 10.6 m), both approaching the coast perpendicularly. After calculating theoretical storm surge elevation, a digital terrain model was made by adjusting topographic data to field work and detailed geomorphological analysis. A model of flooding extent was subsequently developed for each storm type, and then corrected according to the rates of shoreline change in the last decades, which were assessed by means of aerial photographs taking the dune toe as shoreline indicator. Results show that long-term coastline trend represents an important factor in the prediction of flooding extent, since shoreline retreat causes the deterioration of natural coastal defences as dune ridges, thus increasing coastal exposure to high-energy waves. This way, it has been stated that the lack of sedimentary supply plays an important role in spatial variability of inundation extent in Valdelagrana spit. Finally, a hazard map is presented, where calculated coastal retreat rates are employed in order to predict the areas that could be affected by future inundation events.

Detection and Mapping of the Geomorphic Effects of Flooding Using UAV Photogrammetry

NASA Astrophysics Data System (ADS)

Langhammer, Jakub; Vacková, Tereza

2018-04-01

In this paper, we present a novel technique for the objective detection of the geomorphological effects of flooding in riverbeds and floodplains using imagery acquired by unmanned aerial vehicles (UAVs, also known as drones) equipped with an panchromatic camera. The proposed method is based on the fusion of the two key data products of UAV photogrammetry, the digital elevation model (DEM), and the orthoimage, as well as derived qualitative information, which together serve as the basis for object-based segmentation and the supervised classification of fluvial forms. The orthoimage is used to calculate textural features, enabling detection of the structural properties of the image area and supporting the differentiation of features with similar spectral responses but different surface structures. The DEM is used to derive a flood depth model and the terrain ruggedness index, supporting the detection of bank erosion. All the newly derived information layers are merged with the orthoimage to form a multi-band data set, which is used for object-based segmentation and the supervised classification of key fluvial forms resulting from flooding, i.e., fresh and old gravel accumulations, sand accumulations, and bank erosion. The method was tested on the effects of a snowmelt flood that occurred in December 2015 in a montane stream in the Sumava Mountains, Czech Republic, Central Europe. A multi-rotor UAV was used to collect images of a 1-km-long and 200-m-wide stretch of meandering stream with fresh traces of fluvial activity. The performed segmentation and classification proved that the fusion of 2D and 3D data with the derived qualitative layers significantly enhanced the reliability of the fluvial form detection process. The assessment accuracy for all of the detected classes exceeded 90%. The proposed technique proved its potential for application in rapid mapping and detection of the geomorphological effects of flooding.

A framework for global terrain classification using 250-m DEMs to predict geohazards

NASA Astrophysics Data System (ADS)

Iwahashi, J.; Matsuoka, M.; Yong, A.

2016-12-01

Geomorphology is key for identifying factors that control geohazards induced by landslides, liquefaction, and ground shaking. To systematically identify landforms that affect these hazards, Iwahashi and Pike (2007; IP07) introduced an automated terrain classification scheme using 1-km-scale Shuttle Radar Topography Mission (SRTM) digital elevation models (DEMs). The IP07 classes describe 16 categories of terrain types and were used as a proxy for predicting ground motion amplification (Yong et al., 2012; Seyhan et al., 2014; Stewart et al., 2014; Yong, 2016). These classes, however, were not sufficiently resolved because coarse-scaled SRTM DEMs were the basis for the categories (Yong, 2016). Thus, we develop a new framework consisting of more detailed polygonal global terrain classes to improve estimations of soil-type and material stiffness. We first prepare high resolution 250-m DEMs derived from the 2010 Global Multi-resolution Terrain Elevation Data (GMTED2010). As in IP07, we calculate three geometric signatures (slope, local convexity and surface texture) from the DEMs. We create additional polygons by using the same signatures and multi-resolution segmentation techniques on the GMTED2010. We consider two types of surface texture thresholds in different window sizes (3x3 and 13x13 pixels), in addition to slope and local convexity, to classify pixels within the DEM. Finally, we apply the k-means clustering and thresholding methods to the 250-m DEM and produce more detailed polygonal terrain classes. We compare the new terrain classification maps of Japan and California with geologic, aerial photography, and landslide distribution maps, and visually find good correspondence of key features. To predict ground motion amplification, we apply the Yong (2016) method for estimating VS30. The systematic classification of geomorphology has the potential to provide a better understanding of the susceptibility to geohazards, which is especially vital in populated areas.

Geomorphological diversity of Dong-Sha Atoll based on spectrum and texture analysis in high resolution remote sensing imagery

NASA Astrophysics Data System (ADS)

Chen, Jianyu; Mao, Zhihua; He, Xianqiang

2009-01-01

Coral reefs are complex marine ecosystems that are constructed and maintained by biological communities that thrive in tropical oceans. The Dong-Sha Atoll is located at the northern continental margin of the South China Sea. It has being abused by destructive activity of human being and natural event during recent decades. Remote sensing offers a powerful tool for studying coral reef geomorphology and is the most cost-effective approach for large-scale reef survey. In this paper, the high-resolution Quickbird2 imageries which covered the full atoll are used to categorize the current distribution of coral reefs geomorphological structure therein with the auxiliary SPOT5 and ASTER imageries. Spectral and texture analysis are used to distinguish the geomorphological diversity during data processing. The Gray Level Co-occurrence Matrices is adopted for texture feature extraction and atoll geomorphology mapping in the high-resolution pan-color image of Quickbird2. Quickbird2 is considered as the most appropriate image source for coral reefs studies. In the Dong-Sha Atoll, various dynamical geomorphologic units are developed according to wave energy zones. There the reef frame types are classified to 3 different types according as its diversity at the image. The radial structure system is the most characteristic and from high resolution imagery we can distinguish the discrepancy between them.

Scoping of Flood Hazard Mapping Needs for Coos County, New Hampshire

DTIC Science & Technology

2006-01-01

Technical Partner DEM Digital Elevation Model DFIRM Digital Flood Insurance Rate Map DOQ Digital Orthophoto Quadrangle DOQQ Digital Ortho Quarter Quadrangle...color Digital Orthophoto Quadrangles (DOQs)). Remote sensing, base map information, GIS data (for example, contour data, E911 data, Digital Elevation...the feature types found on USGS topographic maps. More recently developed data were derived from digital orthophotos providing improved base map

A digital platform for university education on geomorphosites

NASA Astrophysics Data System (ADS)

Coratza, Paola; Reynard, Emmanuel; Cayla, Nathalie; Comanescu, Laura; Darbellay, Lucie; Giusti, Christian; Grecu, Florina; Pereira, Paulo

2016-04-01

The working group on Geomorphosites of the International Association of Geomorphologists (IAG) is active since 2001 and has developed research activities on issues related to the geomorphological heritage (geomorphosites) (Reynard and Coratza, 2013). In parallel to the research activities, several intensive courses for Ph.D. and Master students have been organized since 2006 in various universities (Lausanne, Lesvos, Minho, Savoie, Beni Mellal) and a textbook for students was edited in 2009 (Reynard et al., 2009). The platform INTERGEO is prepared as a way to disseminate knowledge on geomorphological heritage, in particular in universities of developing countries where access to scientific papers and textbooks is not easy. It aims at improving students' autonomy by the reduction of frontal teaching and increasing autonomous learning as well as promoting international interactions between students interested in geomorphosite topics. The course, developed with the Learning Management System Moodle, is a completely free-access course. It is divided into four parts: (1) Generalities - definitions, links with heritage and landscape studies, active geomorphosites, the IAG working group; (2) Methods - selection and assessment, mapping issues, geomorphosite visualization, technical and digital tools in geomorphosite studies; (3) Conservation and promotion - example of geomorphosite studies related to geoconservation, geoparks, protected areas, World Heritage Sites, geotourism and interpretation, and natural hazards; (4) Examples - cultural, karstic, coastal, mountainous, fluvial, volcanic and anthropogenic geomorphosites. Each chapter contains a short description, a list of references, selected publications, as well as other educational material, e.g. videos, virtual fieldtrips, etc. In particular, several videos allow presenting in a very dynamic way concepts and examples. The content of the course will evolve and will be completed in the future. Most of the content is now ready and is tested by the six universities involved in the project during the academic year 2015-2016. Each university is using INTERGEO as a support for the specific courses on geoconservation and geomorphological heritage. Each team will then carry out fieldwork and will exchange on the results during a virtual international conference to be organized in Summer 2016 (the various teams will interact by video-conferences). The course will then be fully open-access by September 2016. References Reynard, E., Coratza, P. 2013. Scientific research on geomorphosites. A review of the activities of the IAG working group on geomorphosites over the last twelve years. Geogr. Fis. Dinam. Quat., 36, 159-168. Reynard, E., Coratza, P., Regolini-Bissig, G. 2009. (eds). Geomorphosites, München, Pfeil Verlag, 240 p.

Quantitative evaluation of the underground Geoheritage in karst areas: The Picos de Europa National Park, North Spain

NASA Astrophysics Data System (ADS)

Ballesteros, Daniel; Jiménez-Sánchez, Montserrat; José Domínguez-Cuestra, María; García-Sansegundo, Joaquín; Meléndez-Asensio, Mónica

2014-05-01

Karst areas show a lot of kilometers of cave conduits with a hidden Geoheritage poorly investigated in previous works that concerning with their cultural, scientific and education values. The evaluation of cave Geoheritage is complex due to methodological constrains. One of the most important karst areas in the World is the Picos de Europa National Park (North Spain) that was declared as a Global Geosite in 2007 and includes 14 % of the World's Deepest Caves. The GEOCAVE research project is being developed in several caves from the Picos de Europa National Park since 2012 in order to characterize geomorphology and geochronology of the cavities, proposing and validating new methodologies adapted to these environments. The aim of this work is to evaluate the Geoheritage of the Picos de Europa caves based on the studies made in nine selected caves. The methodology includes: 1) elaboration of geomorphological maps of the nine selected caves, projecting geomorphological, geological, hydrogeological, paleontological and cultural forms on the caves surveys; and 2) definition and calculation of three indexes useful to evaluate the Geoheritage of the caves. The indexes are: a) Cave Geoheritage Extension Index (CGhEI), defined as the percentage of the area occupied by the entire features divided by the cave area (excluding the forms that represent the conduits themselves), b) Feature Extension Index (FEI), defined as the area occupied by each group of form divided by the cave area, and c) Cave Geodiversity Index (CGdI), defined as the number of forms divided by the cave area. The nine cave geomorphological maps cover 178,639 m2 of caves and include a whole of 14.9 km of karst conduits, representing these caves the 4.1 % of the conduits of the Picos de Europa. The values of the Cave Geoheritage Extension Index range from 22 to 82 %, while the values of the Feature Extension Indexes for each group of features reach the following values: Geomorphological FEI take values of 20-80 % (speleothems FEI is 15-60 %, fluviokarst FEI is 5-25 %, gravity FEI is 10-40 %); Geological FEI is 4-5 %; Hydrogeological FEI is 0-3 %; Paleontological FEI is 0-0.1% and cultural FEI is 0-4 %. the On the other hand, 84 features are recognized into the caves and the Cave Geodiversity Index ranges from 0.3 to 1.1 features/cm2. These results evidence that 22 to 82 % of the cave conduits are occupy with Geoheritage features, being most of them geomorphological forms (speleothems, fluviokarst and gravity forms). The Geodiversity of the karst caves is high, recognizing a whole of 84 features into the caves and showing a high density of forms. Consequently, underground Geoheritage from karst areas can be estimated combining geomorphological maps few selected caves and three indexes based on number and extensions of the features. These indexes allow us to assign a preliminary weight of the geomorphological, geological, hydrogeological, paleontological and cultural features in a karst area.

ArcticDEM; A Publically Available, High Resolution Elevation Model of the Arctic

NASA Astrophysics Data System (ADS)

Morin, Paul; Porter, Claire; Cloutier, Michael; Howat, Ian; Noh, Myoung-Jong; Willis, Michael; Bates, Brian; Willamson, Cathleen; Peterman, Kennith

2016-04-01

A Digital Elevation Model (DEM) of the Arctic is needed for a large number of reasons, including: measuring and understanding rapid, ongoing changes to the Arctic landscape resulting from climate change and human use and mitigation and adaptation planning for Arctic communities. The topography of the Arctic is more poorly mapped than most other regions of Earth due to logistical costs and the limits of satellite missions with low-latitude inclinations. A convergence of civilian, high-quality sub-meter stereo imagery; petascale computing and open source photogrammetry software has made it possible to produce a complete, very high resolution (2 to 8-meter posting), elevation model of the Arctic. A partnership between the US National Geospatial-intelligence Agency and a team led by the US National Science Foundation funded Polar Geospatial Center is using stereo imagery from DigitalGlobe's Worldview-1, 2 and 3 satellites and the Ohio State University's Surface Extraction with TIN-based Search-space Minimization (SETSM) software running on the University of Illinois's Blue Water supercomputer to address this challenge. The final product will be a seemless, 2-m posting digital surface model mosaic of the entire Arctic above 60 North including all of Alaska, Greenland and Kamchatka. We will also make available the more than 300,000 individual time-stamped DSM strip pairs that were used to assemble the mosaic. The Arctic DEM will have a vertical precision of better than 0.5m and can be used to examine changes in land surfaces such as those caused by permafrost degradation or the evolution of arctic rivers and floodplains. The data set can also be used to highlight changing geomorphology due to Earth surface mass transport processes occurring in active volcanic and glacial environments. When complete the ArcticDEM will catapult the Arctic from the worst to among the best mapped regions on Earth.

Mapping cold-water coral habitats at different scales within the Northern Ionian Sea (Central Mediterranean): an assessment of coral coverage and associated vulnerability.

PubMed

Savini, Alessandra; Vertino, Agostina; Marchese, Fabio; Beuck, Lydia; Freiwald, André

2014-01-01

In this study, we mapped the distribution of Cold-Water Coral (CWC) habitats on the northern Ionian Margin (Mediterranean Sea), with an emphasis on assessing coral coverage at various spatial scales over an area of 2,000 km(2) between 120 and 1,400 m of water depth. Our work made use of a set of data obtained from ship-based research surveys. Multi-scale seafloor mapping data, video inspections, and previous results from sediment samples were integrated and analyzed using Geographic Information System (GIS)-based tools. Results obtained from the application of spatial and textural analytical techniques to acoustic meso-scale maps (i.e. a Digital Terrain Model (DTM) of the seafloor at a 40 m grid cell size and associated terrain parameters) and large-scale maps (i.e. Side-Scan Sonar (SSS) mosaics of 1 m in resolution ground-truthed using underwater video observations) were integrated and revealed that, at the meso-scale level, the main morphological pattern (i.e. the aggregation of mound-like features) associated with CWC habitat occurrences was widespread over a total area of 600 km(2). Single coral mounds were isolated from the DTM and represented the geomorphic proxies used to model coral distributions within the investigated area. Coral mounds spanned a total area of 68 km(2) where different coral facies (characterized using video analyses and mapped on SSS mosaics) represent the dominant macro-habitat. We also mapped and classified anthropogenic threats that were identifiable within the examined videos, and, here, discuss their relationship to the mapped distribution of coral habitats and mounds. The combined results (from multi-scale habitat mapping and observations of the distribution of anthropogenic threats) provide the first quantitative assessment of CWC coverage for a Mediterranean province and document the relevant role of seafloor geomorphology in influencing habitat vulnerability to different types of human pressures.

Comparison between flood prone areas' geomorphic features in the Abruzzo region

NASA Astrophysics Data System (ADS)

Orlando, D.; Giglioni, M.; Magnaldi, S.

2017-07-01

Flood risk maps are one of the main non-structural measures for risk mitigation, but, as the risk knowledge degree is directly proportional to the community interest and financial capability, many sites are devoid of flood inundation areas studies. Recently many authors have investigated the capability of flood prone areas individuation with geomorphological DIGITAL ELEVATION MODEL(DEM) based approaches. These approaches highlight the role of geomorphic features derived from DEM, in this case slope, curvature, elevation, and topographic wetness index, to preliminary inundated areas' identification, without using hydraulic simulations. The present studies aim to analyze the geomorphic features of different hazard levels that lie under the identified inundated areas that have been carried out by the Abruzzo Region Basin Authority. The Aterno-Pescara and Foro river basins have been investigated. The results show that the characteristics of the flooded areas can be clearly distinguished from those of the entire basin,however, the difficultly of geomorphic features in individuatingthe areas of different hazard classifications is obvious.

Deforestation, floodplain dynamics, and carbon biogeochemistry in the Amazon Basin

NASA Technical Reports Server (NTRS)

Bryan, M. L.; Dunne, T.; Richey, J.; Melack, J.; Simonett, D. S.; Woodwell, G.

1984-01-01

Three aspects of the physical geographic environment of the Amazon Basin are considered: (1) deforestation and reforestation, (2) floodplain dynamics, and (3) fluvial geomorphology. Three independent projects are coupled in this experiment to improve the in-place research and to ensure that the Shuttle Imaging Radar-B (SIR-B) experiment stands on a secure base of ongoing work. Major benefits to be obtained center on: (1) areal and locational information, (2) data from various depression angles, and (3) digital radar signatures. Analysis will be conducted for selected sites to define how well SIR-B data can be used for: (1) definition of extent and location of deforestation in a tropical moist forest, (2) definition and quantification of the nature of the vegetation and edaphic conditions on the (floodplain) of the Amazon River, and (3) quantification of the accuracy with which the geometry and channel shifting of the Amazon River may be mapped using SIR-B imagery in conjunction with other remote sensing data.

Using lidar data to analyse sinkhole characteristics relevant for understory vegetation under forest cover-case study of a high karst area in the dinaric mountains.

PubMed

Kobal, Milan; Bertoncelj, Irena; Pirotti, Francesco; Dakskobler, Igor; Kutnar, Lado

2015-01-01

In this article, we investigate the potential for detection and characterization of sinkholes under dense forest cover by using airborne laser scanning data. Laser pulse returns from the ground provide important data for the estimation of digital elevation model (DEM), which can be used for further processing. The main objectives of this study were to map and determine the geomorphometric characteristics of a large number of sinkholes and to investigate the correlations between geomorphology and vegetation in areas with such characteristics. The selected study area has very low anthropogenic influences and is particularly suitable for studying undisturbed karst sinkholes. The information extracted from this study regarding the shapes and depths of sinkholes show significant directionality for both orientation of sinkholes and their distribution over the area. Furthermore, significant differences in vegetation diversity and composition occur inside and outside the sinkholes, which indicates their presence has important ecological impacts.

Using Lidar Data to Analyse Sinkhole Characteristics Relevant for Understory Vegetation under Forest Cover—Case Study of a High Karst Area in the Dinaric Mountains

PubMed Central

Kobal, Milan; Bertoncelj, Irena; Pirotti, Francesco; Dakskobler, Igor; Kutnar, Lado

2015-01-01

In this article, we investigate the potential for detection and characterization of sinkholes under dense forest cover by using airborne laser scanning data. Laser pulse returns from the ground provide important data for the estimation of digital elevation model (DEM), which can be used for further processing. The main objectives of this study were to map and determine the geomorphometric characteristics of a large number of sinkholes and to investigate the correlations between geomorphology and vegetation in areas with such characteristics. The selected study area has very low anthropogenic influences and is particularly suitable for studying undisturbed karst sinkholes. The information extracted from this study regarding the shapes and depths of sinkholes show significant directionality for both orientation of sinkholes and their distribution over the area. Furthermore, significant differences in vegetation diversity and composition occur inside and outside the sinkholes, which indicates their presence has important ecological impacts. PMID:25793871

Scoping of Flood Hazard Mapping Needs for Belknap County, New Hampshire

DTIC Science & Technology

2006-01-01

DEM Digital Elevation Model DFIRM Digital Flood Insurance Rate Map DOQ Digital Orthophoto Quadrangle DOQQ Digital Ortho Quarter Quadrangle DTM...Agriculture Imag- ery Program (NAIP) color Digital Orthophoto Quadrangles (DOQs)). Remote sensing, base map information, GIS data (for example, contour data...found on USGS topographic maps. More recently developed data were derived from digital orthophotos providing improved base map accuracy. NH GRANIT is

A geomorphological characterisation of river systems in South Africa: A case study of the Sabie River

NASA Astrophysics Data System (ADS)

Eze, Peter N.; Knight, Jasper

2018-06-01

Fluvial geomorphology affects river character, behaviour, evolution, trajectory of change and recovery potential, and as such affects biophysical interactions within a catchment. Water bodies in South Africa, in common with many other water-stressed parts of the world, are generally under threat due to increasing natural and anthropogenic influences including aridity, siltation and pollution, as well as climate and environmental change. This study reports on a case study to characterise the geomorphology of different river systems in South Africa, with the aim of better understanding their properties, controls, and implications for biophysical interactions including water quality, biodiversity (aquatic and riparian), and human activity within the catchment. The approach adopted is based on the River Styles® framework (RSF), a geomorphology-based approach developed for rivers in New Zealand and Australia, but applied here for the first time to South Africa. Based on analysis of remote sensing imagery, SRTM-2 digital topographic data and field observations on sites through the entire river system, six geomorphic elements were identified along the Sabie River, northeast South Africa (gorge, bedrock-forced meander, low-moderate sinuosity planform controlled sand bed, meandering sand bed, low sinuosity fine grained sand bed, and floodouts), using the RSF classification scheme and based on the RSF procedural tree of Brierley and Fryirs (2005). Previous geomorphological studies along the Sabie River have shown that different reaches respond differently to episodic floods; we use these data to link river geomorphological character (as defined by the RSF) to the hydrodynamic conditions and processes giving rise to such character. This RSF approach can be used to develop a new management approach for river systems that considers their functional biophysical behaviour within individual reaches, rather than considering them as homogeneous and uniform systems.

High resolution digital mapping and geomorphological analysis of the 2010 Mount Meager rock-debris avalanche (BC, Canada).

NASA Astrophysics Data System (ADS)

Roberti, Gioachino; van Wyk de vries, Benjamin; Ward, Brent; Clague, John; Friele, Pierre; Perotti, Luigi; Giardino, Marco

2016-04-01

This study examines the large landslide that occurred at Mt. Meager, 200 km NNW of Vancouver, British Columbia, Canada, on August 6, 2010. We studied the source area and deposits to reconstruct the failure of the south flank of Mt. Meager from slow deformation to catastrophic collapse, the subsequent transformation into a debris avalanche, and the 11 km run-out. We use a Structure from Motion (SfM) photogrammetric approach and processed both historical British Columbia Provincial airphotos (1948, 1962, 1964-1965, 1973, 1981, 1990, and 2006) and digital images taken with a commercial camera during low-level helicopter traverses. The SfM products have been used to calculate volumes and the geometry of the south flank of Mt. Meager before and after the catastrophic failure, and to produce an orthophoto that we have used to map and describe the deposit. Oblique helicopter photos provide information on the scar geometry and rock units exposed by the failure. The SfM-derived orthophoto and ground observations allowed us to map deposit facies, lithologies, and structures, including thrust, normal, and strike-slip faults. We identified five sub-areas in the accumulation zone based on the association of facies and deformation structures. Based on our interpretation of the remotely sensed data and ground observations, we propose that the landslide had two main rheological phases: one richer in water and highly mobile, and another massive and water-poor. The water-rich phase spread quickly and superelevated high on valley walls as it moved down valley. It left a discontinuous veneer of debris, typically <1 m thick. The main, unsaturated mass moved more slowly and left a thicker (up to about 20 m) deposit with hummocks and brittle-ductile faults and shear zone in the distal part of the run-out zone.

Derivation of Ground Surface and Vegetation in a Coastal Florida Wetland with Airborne Laser Technology

USGS Publications Warehouse

Raabe, Ellen A.; Harris, Melanie S.; Shrestha, Ramesh L.; Carter, William E.

2008-01-01

The geomorphology and vegetation of marsh-dominated coastal lowlands were mapped from airborne laser data points collected on the Gulf Coast of Florida near Cedar Key. Surface models were developed using low- and high-point filters to separate ground-surface and vegetation-canopy intercepts. In a non-automated process, the landscape was partitioned into functional landscape units to manage the modeling of key landscape features in discrete processing steps. The final digital ground surface-elevation model offers a faithful representation of topographic relief beneath canopies of tidal marsh and coastal forest. Bare-earth models approximate field-surveyed heights by + 0.17 m in the open marsh and + 0.22 m under thick marsh or forest canopy. The laser-derived digital surface models effectively delineate surface features of relatively inaccessible coastal habitats with a geographic coverage and vertical detail previously unavailable. Coastal topographic details include tidal-creek tributaries, levees, modest topographic undulations in the intertidal zone, karst features, silviculture, and relict sand dunes under coastal-forest canopy. A combination of laser-derived ground-surface and canopy-height models and intensity values provided additional mapping capabilities to differentiate between tidal-marsh zones and forest types such as mesic flatwood, hydric hammock, and oak scrub. Additional derived products include fine-scale shoreline and topographic profiles. The derived products demonstrate the capability to identify areas of concern to resource managers and unique components of the coastal system from laser altimetry. Because the very nature of a wetland system presents difficulties for access and data collection, airborne coverage from remote sensors has become an accepted alternative for monitoring wetland regions. Data acquisition with airborne laser represents a viable option for mapping coastal topography and for evaluating habitats and coastal change on marsh-dominated coasts. Such datasets can be instrumental in effective coastal-resource management.

Geomorphological processes and frozen ground conditions in Elephant Point (Livingston Island, South Shetland Islands, Antarctica)

NASA Astrophysics Data System (ADS)

Oliva, Marc; Ruiz-Fernández, Jesús

2017-09-01

Elephant Point is an ice-free area in the SW corner of Livingston Island (Maritime Antarctica). The retreat of Rotch Dome glacier during the Holocene has exposed a land area of 1.16 km2. Up to 17.3% of this surface has become ice-free between 1956 and 2010. A detailed geomorphological mapping of this ice-free environment was conducted in late January 2014. A wide range of active periglacial landforms show that periglacial processes are widespread. From the glacier to the coast four different geomorphological areas are identified: proglacial environment, moraine complex, bedrock plateaus and marine terraces. In situ measurements of the thawed soil depth show evidence of the widespread frozen ground conditions in the area. Field observations of permafrost exposures suggest that these frost conditions may be related to a soil permafrost regime, almost down to sea level. The activity of penguin colonies and elephant seals has created minor geomorphological features in the raised marine terraces. Here, several archaeological sites related to early human colonization of Antarctica were also found in natural shelters.

Geomorphology and depositional subenvironments of Gulf Islands National Seashore, Perdido Key and Santa Rosa Island, Florida

USGS Publications Warehouse

Morton, Robert A.; Montgomery, Marilyn C.

2010-01-01

The primary mapping procedures were supervised functions within a Geographic Information System (GIS) that were applied to delineate and classify depositional subenvironments and features, collectively referred to as map units. The delineated boundaries of the map units were exported to create one shapefile, and are differentiated by the field "Type" in the associated attribute table. Map units were delineated and classified based on differences in tonal patterns of features in contrast to adjacent features observed on orthophotography. Land elevations from recent lidar surveys served as supplementary data to assist in delineating the map unit boundaries.

Multidisciplinary approach to evaluate landslide susceptibility along highway in northern Calabria, Italy

NASA Astrophysics Data System (ADS)

Muto, Francesco; Conforti, Massimo; Critelli, Salvatore; Fabbricatore, Davide; Filomena, Luciana; Rago, Valeria; Robustelli, Gaetano; Scarciglia, Fabio; Versace, Pasquale

2014-05-01

The interaction of landslides with linear infrastructures is often the cause of disasters. In Italy landslide impact on roads, railways and buildings cause millions of Euro per year in damage and restoration as well. The proposed study is aimed to the landslide susceptibility evaluation using a multidisciplinary approach: geological and geomorphological survey, statistical analysis and GIS technique, along a section of highway "A3 (Salerno-Reggio Calabria)" between Cosenza Sud and Altilia, northern Calabria. This study is included in a wider research project, named: PON01-01503, Landslides Early Warning-Sistemi integrati per il monitoraggio e la mitigazione del rischio idrogeologico lungo le grandi vie di comunicazione - aimed at the hydrogeological risk mitigation and at the early warning along the highways. The work was first based on air-photo interpretations and field investigations, in order to realize the geological map, geomorphological map and landslide inventory map. In the study area the geomorphology is strongly controlled by its bedrock geology and tectonics. The bedrock geology consists of Neogene sedimentary rocks that cover a thick stack of allochthonous nappes. These nappes consist of crystalline rocks mainly gneiss, phyllite and schist. A total of 835 landslides were mapped and the type of movement are represented mainly by slides and complex and subordinately flow. In order to estimate and validate landslide susceptibility the landslides were divided in two group. One group (training set) was used to prepare susceptibility map and the second group (validation set) to validate the map. Then, the selection of predisposing factors was performed, according with the geological and geomorphological settings of the study area: lithology, distance from tectonic elements, land use, slope, aspect, stream power index (SPI) and plan curvature. In order to evaluate landslide susceptibility Conditional Analysis was applied to Unique Conditions Units (UCUs), that are a unique combination of the predisposing factors. Subsequently, the landslide area is determined within each UCU and the landslide density is computed. The outcome of the study was a classification of the study area into four susceptibility classes, ranked from low to very high. The results showed that the 33% of the study area is characterized by a high to very high degree of susceptibility. The validation procedure results, obtained by crossing the group of the landslide of validation set with the susceptibility map, showed that the predictive model is generally satisfactory; therefore, over 75% of the landslide of validation set is correctly classified falling in high and very high susceptibility classes. The consistency of the model is also suggested by computing the seed cell area index (SCAI) because the high and very high susceptibility classes have very low SCAI values, whereas the SCAI values of the very low and low susceptibility classes are very high. Finally, the landslide susceptibility map provides the baseline information for further evaluations of landslide hazards and related risks.

From hydro-geomorphological mapping to sediment transfer evaluation in the Upper Guil Catchment (Queyras, French Alps)

NASA Astrophysics Data System (ADS)

Lissak, Candide; Fort, Monique; Arnaud-Fassetta, Gilles; Mathieu, Alexandre; Malet, Jean-Philippe; Carlier, Benoit; Betard, François; Cossart, Etienne; Madelin, Malika; Viel, Vincent; Charney, Bérengère; Bletterie, Xavier

2014-05-01

The Guil River catchment (Queyras, Southern French Alps) is prone to hydro-geomorphic hazards related to catastrophic floods, with an amplification of their impacts due to strong hillslope-channel connectivity such as in 1957 (> R.I. 100 yr), and more recently in 2000 (R.I. 30 yr). In both cases, the rainfall intensity, aggravated by pre-existing saturated soils, explained the immediate response of the fluvial system and the subsequent destabilisation of slopes. This resulted in serious damages to infrastructure and buildings in the valley bottom, mostly along some specific reaches and confluences with debris flow prone tributaries. After each event, new protective structures are built. One of the purposes of this study, undertaken in the frame of the SAMCO (ANR) project, was to understand the hydro-geomorphological functioning of this upper Alpine catchment in a context of hazards mitigation and sustainable management of sediment yield, transfer and deposition. To determine the main sediment storages that could be mobilised during the next major hydro-meteorological events, the first step of our study consists in the identification and characterisation of areas that play a role into the sediment transfer processing. From environmental characteristics (channel geometric, vegetation cover…) and anthropogenic factors (hydraulic infrastructures, urban development…), a semi-automatic method provides a typology of contribution areas with sediment storages sensitive to erosion, or areas that will be prone to deposition of sediments during the next flooding event. The second step of the study is focused on the sediment storages with their characterisation and connectivity to the trunk channel. Taking into account the entire catchment and including the torrential system, this phase analyses the sedimentary transfers from the identification and classification of sediment storages to the evaluation of the degree of connectivity with the main or secondary channels. The proposed methodology is based on data directly derived from GIS analysis using interpretation of aerial photographs, regional scale Digital Elevation Model (DEM), high-resolution DEM derived from airborne-based LiDAR, and field survey. The data thus obtained can be used in the final geomorphological map. Future investigations will quantify the contribution of each sub-catchment in the global sediment budget of the Guil catchment. For a better assessment of sediment fluxes and sediment delivery into the main channel network, tracers (pit-tags) and diachronic Terrestrial Laser Scanning will be performed in selected sub-catchments in order to measure erosion rates and contribution to the sediment yield in the valley bottoms during the floods, avalanches and rainfall seasonal events.

Geomorphology and sediment transport on a submerged back-reef sand apron: One Tree Reef, Great Barrier Reef

NASA Astrophysics Data System (ADS)

Harris, Daniel L.; Vila-Concejo, Ana; Webster, Jody M.

2014-10-01

Back-reef sand aprons are conspicuous and dynamic sedimentary features in coral reef systems. The development of these features influences the evolution and defines the maturity of coral reefs. However, the hydrodynamic processes that drive changes on sand aprons are poorly understood with only a few studies directly assessing sediment entrainment and transport. Current and wave conditions on a back-reef sand apron were measured during this study and a digital elevation model was developed through topographic and bathymetric surveying of the sand apron, reef flats and lagoon. The current and wave processes that may entrain and transport sediment were assessed using second order small amplitude (Stokes) wave theory and Shields equations. The morphodynamic interactions between current flow and geomorphology were also examined. The results showed that sediment transport occurs under modal hydrodynamic conditions with waves the main force entraining sediment rather than average currents. A morphodynamic relationship between current flow and geomorphology was also observed with current flow primarily towards the lagoon in shallow areas of the sand apron and deeper channel-like areas directing current off the sand apron towards the lagoon or the reef crest. These results show that the short-term mutual interaction of hydrodynamics and geomorphology in coral reefs can result in morphodynamic equilibrium.

Geomorphology of the Southern Gulf of California Seafloor

NASA Astrophysics Data System (ADS)

Eakins, B. W.; Lonsdale, P. F.; Fletcher, J. M.; Ledesma, J. V.

2004-12-01

A Spring 2004 multibeam sonar survey defined the seafloor geomorphology of the southern part of Gulf of California and the intersection of the East Pacific Rise with the North American continent. Survey goals included mapping structural patterns formed during the rifting that opened the Gulf and identifying the spatial transition from continental rifting to seafloor spreading. Multibeam sonar imagery, augmented with archival data and a subaerial DEM of Mexico, illuminates the principal features of this boundary zone between obliquely diverging plates: (i) active and inactive oceanic risecrests within young oceanic basins that are rich in evidence for off-axis magmatic eruption and intrusion; (ii) transforms with pull-apart basins and transpressive ridges along shearing continental margins and within oceanic crust; (iii) orphaned blocks of continental crust detached from sheared and rifted continental margins; and (iv) young, still-extending continental margins dissected by submarine canyons that in many cases are deeply drowned river valleys. Many of the canyons are conduits for turbidity currents that feed deep-sea fans on oceanic and subsided continental crust, and channel sediment to spreading axes, thereby modifying the crustal accretion process. We present a series of detailed bathymetric and seafloor reflectivity maps of this MARGINS Rupturing Continental Lithosphere focus site illustrating geomorphologic features of the southern part of the Gulf, from Guaymas Basin to the Maria Magdalena Rise.

Analysis of spatial-temporal patterns of water table change as a tool for conjunctive water management in the Upper Central Plain of the Chao Phraya River Basin, Thailand

NASA Astrophysics Data System (ADS)

Vasconcelos, Vitor Vieira; Koontanakulvong, Sucharit; Suthidhummajit, Chokchai; Junior, Paulo Pereira Martins; Hadad, Renato Moreira

2017-03-01

A sustainable strategy for conjunctive water management must include information on the temporal and spatial availability of this natural resource. Because of water shortages in the dry seasons, farmers on the Upper Plain of the Chao Phraya River basin, Thailand, are increasingly using groundwater to meet their irrigation needs. To evaluate the possibilities of conjunctive water management in the area, the spatial-temporal changes in the water table of the Younger Terrace Aquifer were investigated. First, a regional geomorphological map based on field surveys, remote sensing and previous environmental studies was developed. Then, the well data were analyzed in relation to rainfall, streamflow, yield and pumpage, and the data were interpolated using geostatistical techniques. The results were analyzed via integrated zoning based on color theory as applied to multivariate visualization. The analysis results indicate areas that would be more suitable for groundwater extraction in a conjunctive management framework with regard to the natural hydrogeological processes and the effects of human interaction. The kriging results were compared with the geomorphological map, and the geomorphological areas exhibit distinct hydrogeological patterns. The western fans exhibit the best potential for the expansion of conjunctive use, whereas the borders of the northern fans exhibit the lowest potential.

Using Remote Sensing, Geomorphology, and Soils to Map Episodic Streams in Drylands

NASA Astrophysics Data System (ADS)

Thibodeaux-Yost, S. N. S.

2016-12-01

Millions of acres of public land in the California deserts are currently being evaluated and permitted for the construction of large-scale renewable energy projects. The absence of a standard method for identifying episodic streams in arid and semi-arid (dryland) regions is a source of conflict between project developers and the government agencies responsible for conserving natural resources and permitting renewable energy projects. There is a need for a consistent, efficient, and cost-effective dryland stream delineation protocol that accurately reflects the extent and distribution of active watercourses. This thesis evaluates the stream delineation method and results used by the developer for the proposed Ridgecrest Solar Power Project on the El Paso Fan, Ridgecrest, Kern County, California. This evaluation is then compared and contrasted with results achieved using remote sensing, geomorphology, soils, and GIS analysis to identify stream presence on the site. This study's results identified 105 acres of watercourse, a value 10 times greater than that originally identified by the project developer. In addition, the applied methods provide an ecohydrologic base map to better inform project siting and potential project impact mitigation opportunities. This study concludes that remote sensing, geomorphology, and dryland soils can be used to accurately and efficiently identify episodic stream activity and the extent of watercourses in dryland environments.

Multi-scale curvature for automated identification of glaciated mountain landscapes

NASA Astrophysics Data System (ADS)

Prasicek, Günther; Otto, Jan-Christoph; Montgomery, David; Schrott, Lothar

2014-05-01

Automated morphometric interpretation of digital terrain data based on impartial rule sets holds substantial promise for large dataset processing and objective landscape classification. However, the geomorphological realm presents tremendous complexity in the translation of qualitative descriptions into geomorphometric semantics. Here, the simple, conventional distinction of V-shaped fluvial and U-shaped glacial valleys is analyzed quantitatively using the relation of multi-scale curvature and drainage area. Glacial and fluvial erosion shapes mountain landscapes in a long-recognized and characteristic way. Valleys incised by fluvial processes typically have V-shaped cross-sections with uniform and moderately steep slopes, whereas glacial valleys tend to have U-shaped profiles and topographic gradients steepening with distance from valley floor. On a DEM, thalweg cells are determined by a drainage area cutoff and multiple moving window sizes are used to derive per-cell curvature over a variety of scales ranging from the vicinity of the flow path at the valley bottom to catchment sections fully including valley sides. The relation of the curvatures calculated for the user-defined minimum scale and the automatically detected maximum scale is presented as a novel morphometric variable termed Difference of Minimum Curvature (DMC). DMC thresholds determined from typical glacial and fluvial sample catchments are employed to identify quadrats of glaciated and non-glaciated mountain landscapes and the distinctions are validated by field-based geological and geomorphological maps. A first test of the novel algorithm at three study sites in the western United States and a subsequent application to Europe and western Asia demonstrate the transferability of the approach.

The sky is the limit? 20 years of small-format aerial photography taken from UAS for monitoring geomorphological processes

NASA Astrophysics Data System (ADS)

Marzolff, Irene

2014-05-01

One hundred years after the first publication on aerial photography taken from unmanned aerial platforms (Arthur Batut 1890), small-format aerial photography (SFAP) became a distinct niche within remote sensing during the 1990s. Geographers, plant biologists, archaeologists and other researchers with geospatial interests re-discovered the usefulness of unmanned platforms for taking high-resolution, low-altitude photographs that could then be digitized and analysed with geographical information systems, (softcopy) photogrammetry and image processing techniques originally developed for digital satellite imagery. Even before the ubiquity of digital consumer-grade cameras and 3D analysis software accessible to the photogrammetric layperson, do-it-yourself remote sensing using kites, blimps, drones and micro air vehicles literally enabled the questing researcher to get their own pictures of the world. As a flexible, cost-effective method, SFAP offered images with high spatial and temporal resolutions that could be ideally adapted to the scales of landscapes, forms and distribution patterns to be monitored. During the last five years, this development has been significantly accelerated by the rapid technological advancements of GPS navigation, autopiloting and revolutionary softcopy-photogrammetry techniques. State-of-the-art unmanned aerial systems (UAS) now allow automatic flight planning, autopilot-controlled aerial surveys, ground control-free direct georeferencing and DEM plus orthophoto generation with centimeter accuracy, all within the space of one day. The ease of use of current UAS and processing software for the generation of high-resolution topographic datasets and spectacular visualizations is tempting and has spurred the number of publications on these issues - but which advancements in our knowledge and understanding of geomorphological processes have we seen and can we expect in the future? This presentation traces the development of the last two decades by presenting and discussing examples for geomorphological research using UAS, mostly from the field of soil erosion monitoring.

Hazard analysis in active landslide areas in the State of Veracruz, Mexico

NASA Astrophysics Data System (ADS)

Wilde, Martina; Morales Barrera, Wendy V.; Rodriguez Elizarrarás, Sergio R.; Solleiro Rebolledo, Elizabeth; Sedov, Sergey; Terhorst, Birgit

2016-04-01

The year 2013 was characterized by strong storms and hurricanes like the Hurricanes Barbara and Ingrid and the tropical storms Barry and Fernand, which occurred between June and November affecting especially the coastal regions of Mexico. First of all, the State of Veracruz experienced a series of intense rainfalls and as consequences of these events over 780 landslides were registered. More than 45000 people suffered from evacuations. Located on the coast of the Gulf of Mexico, Veracruz has a wide range of altitude differences. The area with the highest elevations reaches from 5675 m.a.s.l. (Pico de Orizaba, the highest mountain of Mexico) to approximately 3000 m.a.s.l. and is characterized by steep slopes and V-shaped valleys. The mountains are part of the Sierra Madre Oriental and the Trans-Mexican Volcanic Belt. Plateaus and rounded hills are typical for the intermediate zones (3000 - 500 m.a.s.l.). The lowest zone (from 500 m.a.s.l. to sea level) is defined by moderate slopes, large rivers and coastal plain areas. The geology shows a variety and complexity of sedimentary and volcanic rocks. The sedimentary formations comprise claystones, siltstones, sandstones and calcareous rocks. Plateaus of basalts and andesites and deposits of ignimbrites are representative for this area. Even though Veracruz is a region highly endangered by landslides, currently there are no susceptibility maps or any other relevant information with high spatial resolution. Because of the lack of high definite information about the landslide hazards in this area, detailed investigations about the conditions (geology, geomorphology, thresholds, etc.) are indispensable. A doctoral grant from the German Academic Exchange Service (DAAD) allowed to carry out investigations in areas affected by large landslides in the year 2013. The selected study sites comprise damaged infrastructures and settlements. With a multi-methodological and interdisciplinary approach different processes and types of mass movements are analyzed in order to reconstruct complex interrelations of the causes and effects of landslide events. One of the major objectives of this research is to evaluate the potential hazard of active landslide areas. Detailed field analyzes were performed to investigate the situations and dynamics of the slope movements. Therefore, geomorphological mapping, sediment characterization as well as geophysical methods are applied. On the one hand, a detailed sediment characterization aims to identify the type of material (e.g. geotechnical attributes), on the other sediments can provide information on different activity phases, respectively movement processes in slide masses. Furthermore, the focus is placed on the determination of landslide relevant parameters and thresholds. Digital elevation models, which were generated before the onset of slope movements, are integrated in the geomorphological analysis. The poster presents the specific study sites in Veracruz and the situation of endangered slopes before and after the landslide events. It is planned to use this knowledge to model susceptibility maps for the region in the future. Moreover, field data will be used as basic information for further monitoring plans. Resulting susceptibility maps will be provided to the responsible authorities in order to support sustainable planning of settlements and infrastructure in hazardous regions.

Tectonic geomorphology of the Andes with SIR-A and SIR-B

NASA Technical Reports Server (NTRS)

Bloom, Arthur L.; Fielding, Eric J.

1986-01-01

Data takes from SIR-A and SIR-B (Shuttle Imaging Radar) crossed all of the principal geomorphic provinces of the central Andes between 17 and 34 S latitude. In conjunction with Thematic Mapping images and photographs from hand-held cameras as well as from the Large Format Camera that was flown with SIR-B, the radar images give an excellent sampling of Andean geomorphology. In particular, the radar images show new details of volcanic rocks and landforms of late Cenozoic age in the Puna, and the exhumed surfaces of tilted blocks of Precambrian crystalline basement in the Sierras Pampeanas.

Geologic interpretation and multibeam bathymetry of the sea floor in the vicinity of the Race, eastern Long Island Sound

USGS Publications Warehouse

Poppe, L.J.; DiGiacomo-Cohen, M. L.; Doran, E.F.; Smith, S.M.; Stewart, H.F.; Forfinski, N.A.

2007-01-01

Digital terrain models (DTMs) produced from multibeam bathymetric data provide valuable base maps for marine geological interpretations (Todd and others, 1999; Mosher and Thomson, 2002; ten Brink and others, 2004; Poppe and others, 2006a, b, c, d). These maps help define the geological variability of the sea floor (one of the primary controls of benthic habitat diversity), improve our understanding of the processes that control the distribution and transport of bottom sediments and the distribution of benthic habitats and associated infaunal community structures, and provide a detailed framework for future research, monitoring, and management activities. The bathymetric survey interpreted herein (National Oceanic and Atmospheric Administration (NOAA) survey H11250) covers roughly 94 km² of sea floor in an area where a depression along the Orient Point-Fishers Island segment of the Harbor Hill-Roanoke Point-Charlestown Moraine forms the Race, the eastern opening to Long Island Sound. The Race also divides easternmost Long Island Sound from northwestern Block Island Sound (fig. 1). This bathymetry has been examined in relation to seismic reflection data collected concurrently, as well as archived seismic profiles acquired as part of a long-standing geologic mapping partnership between the State of Connecticut and the U.S. Geological Survey (USGS). The objective of this work was to use these acoustic data sets to interpret geomorphological attributes of the sea floor, and to use these interpretations to better understand the Quaternary geologic history and modern sedimentary processes.

Geoarchaeology and geomorphology of Phoenicus ancient harbor, NW coast of Egypt

NASA Astrophysics Data System (ADS)

Moustafa, Samah; Torab, Magdy

2016-04-01

Phoenicus Greek harbor located in SE coastline of Ras El Hekma area, west of Alexandria city for about 220 km. It is shaped as triangle with its headland extending into the Mediterranean Sea for about 15 km. It is occupied by sedimentary rocks belonging to the Tertiary and Quaternary Eras, the western coastline consists of Pleistocene, Separated polygons of limestone sheets and fossil lime stone, where there are coastal platforms, fluvial forms and solution holes. The location and description of Phoenicus ancient harbor were mentioned by some late writers (Fourtau,1893) & (Muller,1901), some geoarchaeological indicators were discovered by the authors such as fish tanks, well, remains of breakwater and wine press. The present work is mainly devoted to define the geomorphological and geoarchaelological indicators of Phoenicus Greek harbor site, based on detailed geomorphological and geoarchaelogical surveying, sampling, dating and mapping as well as satellite image interpretation and GIS techniques.

Hyperspectral remote sensing exploration of carbonatite - an example from Epembe, Kunene region, Namibia

NASA Astrophysics Data System (ADS)

Zimmermann, Robert; Brandmeier, Melanie; Andreani, Louis; Gloaguen, Richard

2015-04-01

Remote sensing data can provide valuable information about ore deposits and their alteration zones at surface level. High spectral and spatial resolution of the data is essential for detailed mapping of mineral abundances and related structures. Carbonatites are well known for hosting economic enrichments in REE, Ta, Nb and P (Jones et al. 2013). These make them a preferential target for exploration for those critical elements. In this study we show how combining geomorphic, textural and spectral data improves classification result. We selected a site with a well-known occurrence in northern Namibia: the Epembe dyke. For analysis LANDSAT 8, SRTM and airborne hyperspectral (HyMap) data were chosen. The overlapping data allows a multi-scale and multi-resolution approach. Results from data analysis were validated during fieldwork in 2014. Data was corrected for atmospherical and geometrical effects. Image classification, mineral mapping and tectonic geomorphology allow a refinement of the geological map by lithological mapping in a second step. Detailed mineral abundance maps were computed using spectral unmixing techniques. These techniques are well suited to map abundances of carbonate minerals, but not to discriminate the carbonatite itself from surrounding rocks with similar spectral signatures. Thus, geometric indices were calculated using tectonic geomorphology and textures. For this purpose the TecDEM-toolbox (SHAHZAD & GLOAGUEN 2011) was applied to the SRTM-data for geomorphic analysis. Textural indices (e.g. uniformity, entropy, angular second moment) were derived from HyMap and SRTM by a grey-level co-occurrence matrix (CLAUSI 2002). The carbonatite in the study area is ridge-forming and shows a narrow linear feature in the textural bands. Spectral and geometric information were combined using kohonen Self-Organizing Maps (SOM) for unsupervised clustering. The resulting class spectra were visually compared and interpreted. Classes with similar signatures were merged according to geological context. The major conclusions are: 1. Carbonate minerals can be mapped using spectral unmixing techniques. 2. Carbonatites are associated with specific geometric pattern 3. The combination of spectral and geometric information improves classification result and reduces misclassification. References Clausi, D. A. (2002): An analysis of co-occurrence texture statistics as a function of grey-level quantization. - Canadian Journal of Remote Sensing, 28 (1), 45-62 Jones, A. P., Genge, M. and Carmody, L (2013): Carbonate Melts and Carbonatites. - Reviews in Mineralogy & Geochemistry, 75, 289-322 Shahzad, F. & Gloaguen, R. (2011): TecDEM: A MATLAB based toolbox for tectonic geomorphology, Part 2: Surface dynamics and basin analysis. - Computers and Geosciences, 37 (2), 261-271

Reports of planetary geology program, 1983

NASA Technical Reports Server (NTRS)

Holt, H. E. (Compiler)

1984-01-01

Several areas of the Planetary Geology Program were addressed including outer solar system satellites, asteroids, comets, Venus, cratering processes and landform development, volcanic processes, aeolian processes, fluvial processes, periglacial and permafrost processes, geomorphology, remote sensing, tectonics and stratigraphy, and mapping.

LIDAR data to support coastal erosion analysis: the Conero study case

NASA Astrophysics Data System (ADS)

Calligaro, Simone; Sofia, Giulia; Guarnieri, Alberto; Tarolli, Paolo

2013-04-01

In the last decades, the topic of coastal erosion and the derived risk have been subject of a growing interest for public authorities and researchers. Recent major natural events, such as hurricanes, tsunamis, and sea level rising, called the attention of media and society, underlining serious concerns about such problems. In a high-density populated country such as Italy, where tourism is one of the major economic activities, the coastal erosion is really a critical issue. In April 2010, along a reach of the coast of Ventotene Island, two young students tragically died, killed by a rock fall. This event dramatically stressed public authorities about the effectiveness of structural and non-structural measures for the mitigation of such phenomena. It is clear that an improving of the actual knowledge about coastal erosion is needed, especially to monitor such events and to set alert systems. In the last few years, airborne LIDAR technology led to a dramatic increase in terrain information. Airborne LiDAR and Terrestrial Laser Scanner (TLS) derived high-resolution Digital Terrain Models (DTMs) have opened avenues for hydrologic and geomorphologic studies (Tarolli et al., 2009). In general, all the main surface processes signatures are correctly recognized using a DTM with cell sizes of 1 m. Having said that, some sub-meter grid sizes may be more suitable in those situations where the analysis of micro topography related to micro changes due to slope failures is critical for risk assessment, and the Terrestrial Laser Scanner (TLS) has been proven to be a useful tool for such detailed field survey. The acquired elevation data with TLS allow to derive a centimeters high quality DTMs. The possibility to detect in detail the slope failures signatures results in a better understanding and mapping of the erosion susceptibility, and of those areas where slope failures are more likely to happen. In addition, these information can be also considered as the basis to develop risk maps. At this regard, a clear example is the case of coastal erosion. In this work a detailed TLS survey was carried out in summer 2012, in the Conero Regional Park (Marche, province of Ancona), along the "spiaggia Urbani" and "spiaggia San Michele". These two study areas present several sections affected by erosion, rock falls and slope failures. They are also a part of a very prestigious place for tourism during the summer season; therefore deriving risk maps is critical. Thanks to the TLS survey, it was possible to obtain a 10 cm resolution DTM covering a reach of about 1.5 km of the coast. This high resolution DTM was used to derive topographic attributes such as curvature from which it has been possible to automatically recognize (Tarolli et al, 2012) and map the surface features related to any surface instabilities. These topographic information and results will also serve as the reference point for future yearly TLS surveys, that absolutely will help in recognizing any micro changes and slope failures, improving the delineation of risk maps. References Tarolli, P., Arrowsmith, J.R., Vivoni, E.R. (2009). Understanding earth surface processes from remotely sensed digital terrain models, Geomorphology, 113, 1-3, doi:10.1016/j.geomorph. 2009.07.005. Tarolli, P., Sofia, G., Dalla Fontana, G. (2012). Geomorphic features extraction from high-resolution topography: landslide crowns and bank erosion, Natural Hazards, 61, 65-83, doi:10.1007/s11069-010-9695-2.

Space geodiversity review: a case study in the southwestern region of Paraná State, Brazil.

NASA Astrophysics Data System (ADS)

Manosso, Fernando; Tauana Basso, Bruna; Alcindo Da Roza, Douglas; Souza dos Santos, Daniel

2015-04-01

Considering the strong global concern for nature protection, improvements emerge to support techniques to understand physical and biological means of selecting areas for environmental conservation. Most techniques take into consideration mainly the biological characteristics of nature, however as the nature is a complex of biotic and abiotic elements it becomes thus necessary the creation of parameters to understand the diversity of abiotic elements, their distribution, occurrence, threats and values as well. This paper aims to identify, quantify and perform a spatial analysis of the distribution of geodiversity in the southwestern region of Paraná State, Brazil, from the different concepts of geodiversity with the use of techniques on digital cartographic database in a Geographic Information System - GIS. Gray (2004) conceptualized geodiversity as the natural distribution of geology, including rocks, minerals, fossils, soil characteristics, land forms and processes (geomorphology), and their connections. Geodiversity is composed by the variability of abiotic nature, including lithological elements, tectonic, geomorphological, edaphic, hydrological, topographical and physical processes of the Earth surface, seas, oceans, together with natural endogenous, exogenous and anthropogenic processes that include a diversity of particles, elements and places (Serrano and Ruiz Flaño, 2007). Different methods of quantitative assessment of geodiversity in different territories were applied by Carcavilla et al (2007), Pellitero and González-Amuchastegui (2010), Navarro (2010), Katerina and Dušan (2008), Serrano et al (2007; 2009), Kozlowski (2010), Zwolinski and Stachowiak (2012), Thomas (2012), Hjort and Luoto (2010; 2012), Pellitero et al (2014), and Silva (2014). Considering geodiversity as the abiotic elements which constitute the landscape; it is important to mention that such set may vary spatially according to the occurrence of different geological formations, rock types, landforms, occurrence of fossils, drainage system, soil and other processes that outline the geodiversity. In addition to the wealth index number, which presents a quantity and area ratio, another way of analyzing the geodiversity of a case study is the abundance, dominance or the relative frequency of geodiversity (Carcavilla et al, 2007). As for the southwestern region of Paraná State case study, we used a set of cartographic databases at the 1:250.000 scale; for example: geomorphological and soil compartments, rivers, geological formations, structural lineaments, as well as temperature, rainfall and humidity average maps. The maps were organized relating the attribute tables, quantifying the sum of different elements each sample cell contained in a regular grid of 4km2. As a result, a map of the geodiversity wealth index of the region has been generated. High geodiversity wealth index comprises more carved valleys with steep slopes on some structural lines; on the other hand, less wealthy areas are located on softer relief plateaus with large hills, more homogeneous soils and lower relief structural control. These results, as well as adjustments and efficiency of the method seem to indicate an important tool for area management, especially regarding the selection of priority areas for nature conservation.

A Servicewide Benthic Mapping Program for National Parks

USGS Publications Warehouse

Moses, Christopher S.; Nayegandhi, Amar; Beavers, Rebecca; Brock, John

2010-01-01

In 2007, the National Park Service (NPS) Inventory and Monitoring Program directed the initiation of a benthic habitat mapping program in ocean and coastal parks in alignment with the NPS Ocean Park Stewardship 2007-2008 Action Plan. With 74 ocean and Great Lakes parks stretching over more than 5,000 miles of coastline across 26 States and territories, this Servicewide Benthic Mapping Program (SBMP) is essential. This program will deliver benthic habitat maps and their associated inventory reports to NPS managers in a consistent, servicewide format to support informed management and protection of 3 million acres of submerged National Park System natural and cultural resources. The NPS and the U.S. Geological Survey (USGS) convened a workshop June 3-5, 2008, in Lakewood, Colo., to discuss the goals and develop the design of the NPS SBMP with an assembly of experts (Moses and others, 2010) who identified park needs and suggested best practices for inventory and mapping of bathymetry, benthic cover, geology, geomorphology, and some water-column properties. The recommended SBMP protocols include servicewide standards (such as gap analysis, minimum accuracy, final products) as well as standards that can be adapted to fit network and park unit needs (for example, minimum mapping unit, mapping priorities). SBMP Mapping Process. The SBMP calls for a multi-step mapping process for each park, beginning with a gap assessment and data mining to determine data resources and needs. An interagency announcement of intent to acquire new data will provide opportunities to leverage partnerships. Prior to new data acquisition, all involved parties should be included in a scoping meeting held at network scale. Data collection will be followed by processing and interpretation, and finally expert review and publication. After publication, all digital materials will be archived in a common format. SBMP Classification Scheme. The SBMP will map using the Coastal and Marine Ecological Classification Standard (CMECS) that is being modified to include all NPS needs, such as lacustrine ecosystems and submerged cultural resources. CMECS Version III (Madden and others, 2010) includes components for water column, biotic cover, surface geology, sub-benthic, and geoform. SBMP Data Archiving. The SBMP calls for the storage of all raw data and final products in common-use data formats. The concept of 'collect once, use often' is essential to efficient use of mapping resources. Data should also be shared with other agencies and the public through various digital clearing houses, such as Geospatial One-Stop (http://gos2.geodata.gov/wps/portal/gos). To be most useful for managing submerged resources, the SBMP advocates the inventory and mapping of the five components of marine ecosystems: surface geology, biotic cover, geoform, sub-benthic, and water column. A complete benthic inventory of a park would include maps of bathymetry and the five components of CMECS. The completion of mapping for any set of components, such as bathymetry and surface geology, or a particular theme (for example, submerged aquatic vegetation) should also include a printed report.

Glaciation style and the geomorphological record: evidence for Younger Dryas glaciers in the eastern Lake District, northwest England

NASA Astrophysics Data System (ADS)

McDougall, Derek

2013-08-01

The Younger Dryas (c. 12,900-11,700 years ago) in Britain witnessed renewed glaciation, with the readvance of ice masses that had survived the preceding Lateglacial Interstadial as well as the formation of new glaciers. The extents of these former glaciers have been mapped by many workers over the past fifty years, usually as a basis for palaeoclimatic investigations. It has frequently been asserted that the landform record is sufficiently clear to allow accurate ice mass reconstructions at or near maximum extents. Detailed geomorphological mapping in the eastern Lake District in NW England, however, demonstrates that this confidence may not always be warranted. Whereas previous workers have interpreted the well-developed moraines that exist in some locations as evidence for an alpine-style of glaciation, with ice restricted to a small number of valleys, this study shows that the most recent glaciation to affect the area was characterised by: (i) extensive summit icefields, which supplied ice to the surrounding valleys; and (ii) a much greater volume of ice in the valleys than previously thought. The discovery that summit icefields were relatively common at this time is consistent with recent studies elsewhere in the Lake District and beyond. More significant, however, is the recognition that changing glacier-topographic interactions over both space and time appears to have had a profound impact on valley-floor glacial landform development, with the absence of clear moraines not necessarily indicating ice-free conditions at this time. This complicates glacier reconstructions based solely on the geomorphological record. Similar geomorphological complexity may be present in other areas that previously supported summit icefields, and this needs to be taken into account in glacier reconstructions.

High-resolution CASSINI-VIMS mosaics of Titan and the icy Saturnian satellites

USGS Publications Warehouse

Jaumann, R.; Stephan, K.; Brown, R.H.; Buratti, B.J.; Clark, R.N.; McCord, T.B.; Coradini, A.; Capaccioni, F.; Filacchione, G.; Cerroni, P.; Baines, K.H.; Bellucci, G.; Bibring, J.-P.; Combes, M.; Cruikshank, D.P.; Drossart, P.; Formisano, V.; Langevin, Y.; Matson, D.L.; Nelson, R.M.; Nicholson, P.D.; Sicardy, B.; Sotin, Christophe; Soderbloom, L.A.; Griffith, C.; Matz, K.-D.; Roatsch, Th.; Scholten, F.; Porco, C.C.

2006-01-01

The Visual Infrared Mapping Spectrometer (VIMS) onboard the CASSINI spacecraft obtained new spectral data of the icy satellites of Saturn after its arrival at Saturn in June 2004. VIMS operates in a spectral range from 0.35 to 5.2 ??m, generating image cubes in which each pixel represents a spectrum consisting of 352 contiguous wavebands. As an imaging spectrometer VIMS combines the characteristics of both a spectrometer and an imaging instrument. This makes it possible to analyze the spectrum of each pixel separately and to map the spectral characteristics spatially, which is important to study the relationships between spectral information and geological and geomorphologic surface features. The spatial analysis of the spectral data requires the determination of the exact geographic position of each pixel on the specific surface and that all 352 spectral elements of each pixel show the same region of the target. We developed a method to reproject each pixel geometrically and to convert the spectral data into map projected image cubes. This method can also be applied to mosaic different VIMS observations. Based on these mosaics, maps of the spectral properties for each Saturnian satellite can be derived and attributed to geographic positions as well as to geological and geomorphologic surface features. These map-projected mosaics are the basis for all further investigations. ?? 2006 Elsevier Ltd. All rights reserved.

Digital geologic map of the Coeur d'Alene 1:100,000 quadrangle, Idaho and Montana

USGS Publications Warehouse

digital compilation by Munts, Steven R.

2000-01-01

Between 1961 and 1969, Alan Griggs and others conducted fieldwork to prepare a geologic map of the Spokane 1:250,000 map (Griggs, 1973). Their field observations were posted on paper copies of 15-minute quadrangle maps. In 1999, the USGS contracted with the Idaho Geological Survey to prepare a digital version of the Coeur d’Alene 1:100,000 quadrangle. To facilitate this work, the USGS obtained the field maps prepared by Griggs and others from the USGS Field Records Library in Denver, Colorado. The Idaho Geological Survey (IGS) digitized these maps and used them in their mapping program. The mapping focused on field checks to resolve problems in poorly known areas and in areas of disagreement between adjoining maps. The IGS is currently in the process of preparing a final digital spatial database for the Coeur d’Alene 1:100,000 quadrangle. However, there was immediate need for a digital version of the geologic map of the Coeur d’Alene 1:100,000 quadrangle and the data from the field sheets along with several other sources were assembled to produce this interim product. This interim product is the digital geologic map of the Coeur d’Alene 1:100,000 quadrangle, Idaho and Montana. It was compiled from the preliminary digital files prepared by the Idaho Geological, and supplemented by data from Griggs (1973) and from digital databases by Bookstrom and others (1999) and Derkey and others (1996). The resulting digital geologic map (GIS) database can be queried in many ways to produce a variety of geologic maps. Digital base map data files (topography, roads, towns, rivers and lakes, etc.) are not included: they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:100,000 (e.g., 1:62,500 or 1:24,000). The digital geologic map graphics (of00-135_map.pdf) that are provided are representations of the digital database. The map area is located in north Idaho. This open-file report describes the geologic map units, the methods used to convert the geologic map data into a digital format, the ArcInfo GIS file structures and relationships, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet.

Hydrographic Basins Analysis Using Digital Terrain Modelling

NASA Astrophysics Data System (ADS)

Mihaela, Pişleagă; -Minda Codruţa, Bădăluţă; Gabriel, Eleş; Daniela, Popescu

2017-10-01

The paper, emphasis the link between digital terrain modelling and studies of hydrographic basins, concerning the hydrological processes analysis. Given the evolution of computing techniques but also of the software digital terrain modelling made its presence felt increasingly, and established itself as a basic concept in many areas, due to many advantages. At present, most digital terrain modelling is derived from three alternative sources such as ground surveys, photogrammetric data capture or from digitized cartographic sources. A wide range of features may be extracted from digital terrain models, such as surface, specific points and landmarks, linear features but also areal futures like drainage basins, hills or hydrological basins. The paper highlights how the use appropriate software for the preparation of a digital terrain model, a model which is subsequently used to study hydrographic basins according to various geomorphological parameters. As a final goal, it shows the link between digital terrain modelling and hydrographic basins study that can be used to optimize the correlation between digital model terrain and hydrological processes in order to obtain results as close to the real field processes.

An historical look at the Binghamton Geomorphology Symposium

NASA Astrophysics Data System (ADS)

Sawyer, Carol F.; Butler, David R.; O'Rourke, Tela

2014-10-01

The Binghamton Geomorphology Symposium (BGS) is an annual meeting held since 1970, usually in the U.S.A., on timely topics in the field of geomorphology. A special issue of this journal presents the papers from each meeting and provides an opportunity to disseminate to the international community research relevant to that year's theme written by key people in that field. In this paper, we review the history of the BGS, examine the academic disciplines of each year's organizers, compile a list of the researchers who have made multiple contributions to BGS, note the citation impact of papers published in the annual proceedings, map the spatial distribution of the meeting locations, and categorize the gender distribution of the contributors to the symposium. Contributions from female authors to the BGS have steadily increased since the 1970s; however, from 2003 to 2013, females still only accounted for 23.6% of the proceeding's papers, an increase of 16.4% from the 1970s. These numbers are not surprising when compared to the gender distribution of the top positions in specialty groups in the U.S. Between 1989 and 2010, over 7000 citations were from articles published in BGS special issues, indicating their contributions to the geomorphology field. When normalized by the number of years the articles have been available, papers from BGS whose themes combined geomorphology with other fields (i.e., natural hazards and geomorphology), rated higher numbers of citations. The dispersion of the location of BGS meetings illustrates how the series is maturing by moving away from its origin in the U.S. northeast.

Geodiversity, geoheritage and cultural landscape: an example from the Messinian geosites of the Piemonte region (NW-Italy)

NASA Astrophysics Data System (ADS)

Giordano, Enrico; Natalicchio, Marcello; Ghiraldi, Luca; Lozar, Francesca; Dela Pierre, Francesco; Giardino, Marco

2015-04-01

The Piemonte region (NW-Italy) contains a remarkable diversity of landscapes, some of them included in and protected by the World Heritage list, as well as some recently proposed geosites which testify the dramatic paleoevironmental, paleobiological and paleoclimatic event that occurred in the Mediterranean area around 6 Ma ago during the so-called Messinian Salinity Crisis (MSC). However the link between landform, geodiversity, geoheritage, and cultural landscape has not yet fully explored. The aims of this study, promoted by the multidisciplinary research project 'PROGEO-Piemonte' (PROactive management of GEOlogical heritage in the Piemonte region), are: 1) to analyse the link between geosites and recent landscape modification, 2) to reconstruct the landscape evolution and, through geotourism, 3) to promote geological knowledge in an area with great potential for tourism. The study area is located in the SE part of the Cuneo plain, at the foot of the Langhe hills, where heterogeneous landforms, mainly related to the Tanaro river piracy, are observed. The sediments recording the MSC event, mostly consisting of thick gypsum layers, have been recently studied by a multidisciplinary approach and the results allowed the detailed reconstruction of the MSC evolution in this region. Two maps have been produced to disseminate the geodiversity knowledge (the geological - landscape map) and to promote geotourism fruition (the geotouristic map). The geological - landscape map deals with different geological and geomorphologic issues thanks to illustrations of the main features of the Messinian deposits, their depositional environments and the exposed landforms. To underline the high geodiversity of the area, it has been divided into several geomorphologic sectors based of their characteristic landforms and evolution. In each of these sectors, geosites have been identified to clarify the comprehension of the related topics at the widest public: particularly, the geosites help to reconstruct the stages of the MSC and to understand the implication of fast environmental changes on the living beings. The geotouristic map describes the geological and geomorphologic features with a simpler language and shorter form than the previous one. Trails, viewpoints and museums are reported on the map to facilitate the comprehension of the landscape and to create a link between scientific issues and human activities (i.e. use of gypsum in the building industry). Moreover the geomorphologic analysis of the present landscape allows to decipher its recent evolution and to evaluate the risks connected with the tourist fruition, thus improving the potential safe use of anthropogenic landforms for geo-environmental education. Here the MSC is dealt with through the stages of scientific discoveries that led to the formulation of the current theories. In conclusion, the produced maps may help both to improve people knowledge and awareness on environmental modification and past climate variability and to address the crucial question whether they could happen again in the future.

To assess the value of satellite imagery in resource inventorization on a national scale

NASA Technical Reports Server (NTRS)

Malan, O. G. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Production of 1:500,000 scale false color photolithoprints proved to be very valuable. Significant results were obtained in geomorphological mapping, mapping of disturbed and undisturbed natural vegetation as well as in the discovery of major geologic lineaments, some of which may be associated with mineralization. The cartographic quality of system corrected MSS imagery was also evaluated.

The value of ERTS-1 imagery in resource inventorization on a national scale in South Africa

NASA Technical Reports Server (NTRS)

Malan, O. G.; Macvicar, C. N.; Edwards, D.; Temperley, B. N.; Claassen, L.

1974-01-01

It has been shown that ERTS imagery, particularly in the form of 1:500,000 scale false color photolithographic prints, can contribute very significantly towards facilitating and accelerating (dramatically, in some cases) resource surveys and geologic mapping. Fire mapping on a national scale becomes a feasability; numerous new geologic features, particularly lineaments, have been discovered, land use can be mapped efficiently on a regional scale and degraded areas identified. The first detailed tectonic and geomorphological maps of the Republic of South Africa will be published mainly owing to the availability of ERTS images.

Mapping Surface Features Produced by an Active Landslide

NASA Astrophysics Data System (ADS)

Parise, Mario; Gueguen, Erwan; Vennari, Carmela

2016-10-01

A large landslide reactivated on December 2013, at Montescaglioso, southern Italy, after 56 hours of rainfall. The landslide disrupted over 500 m of a freeway, involved a few warehouses, a supermarket, and private homes. After the event, it has been performed field surveys, aided by visual analysis of terrestrial and helicopter photographs, to compile a map of the surface deformations. The geomorphological features mapped included single fractures, sets of fractures, tension cracks, trenches, and pressure ridges. In this paper we present the methodology used, the map obtained through the intensive field work, and discuss the main surface features produced by the landslide.

An interactive method for digitizing zone maps

NASA Technical Reports Server (NTRS)

Giddings, L. E.; Thompson, E. J.

1975-01-01

A method is presented for digitizing maps that consist of zones, such as contour or climatic zone maps. A color-coded map is prepared by any convenient process. The map is then read into memory of an Image 100 computer by means of its table scanner, using colored filters. Zones are separated and stored in themes, using standard classification procedures. Thematic data are written on magnetic tape and these data, appropriately coded, are combined to make a digitized image on tape. Step-by-step procedures are given for digitization of crop moisture index maps with this procedure. In addition, a complete example of the digitization of a climatic zone map is given.

Spatially distributed rockfall activity inferred from talus deposits and corresponding rockwall areas in the Gradenbach catchment (Schober Mountains, Austria)

NASA Astrophysics Data System (ADS)

Götz, Joachim; Buckel, Johannes; Heckmann, Tobias

2013-04-01

The analysis of alpine sediment cascades requires the identification, differentiation and quantification of sediment sources, storages, and transport processes. This study deals with the origin of alpine sediment transfer and relates primary talus deposits to corresponding rockwall source areas within the Gradenbach catchment (Schober Mountains, Austrian Alps). Sediment storage landforms are based on a detailed geomorphological map of the catchment which was generated to analyse the sediment transfer system. Mapping was mainly performed in the field and supplemented by post-mapping analysis using LIDAR data and digital orthophotos. A fundamental part of the mapping procedure was to capture additional landform-based information with respect to morphometry, activity and connectivity. The applied procedure provides a detailed inventory of sediment storage landforms including additional information on surface characteristics, dominant and secondary erosion and deposition processes, process activity and sediment storage coupling. We develop the working hypothesis that the present-day surface area ratio between rockfall talus (area as a proxy for volume, backed by geophysical analysis of selected talus cones) and corresponding rockwall source area is a measure of rockfall activity since deglaciation; large talus cones derived from small rockwall catchments indicate high activity, while low activity can be inferred where rockfall from large rock faces has created only small deposits. The surface area ratio of talus and corresponding rockwalls is analysed using a landform-based and a process-based approach. For the landform-based approach, we designed a GIS procedure which derives the (hydrological) catchment area of the contact lines of talus and rockwall landforms in the geomorphological map. The process-based approach simulates rockfall trajectories from steep (>45°) portions of a DEM generated by a random-walk rockfall model. By back-tracing those trajectories that end on a selected talus landform, the 'rockfall contributing area' is delineated; this approach takes account of the stochastic nature of rockfall trajectories and is able to identify, for example, rockfall delivery from one rockwall segment to multiple talus landforms (or from multiple rockfall segments to the same deposit, respectively). Using both approaches, a total of 290 rockwall-talus-subsystems are statistically analysed indicating a constant relationship between rockfall source areas and corresponding areas of talus deposits of almost 1:1. However, certain rockwall-talus-subsystems deviate from this correlation since sediment storage landforms of similar size originate from varying rockwall source areas and vice versa. This varying relationship is assumed to be strongly controlled by morphometric parameters, such as rockwall slope, altitudinal interval, and aspect. The impact of these parameters on the surface area ratio will be finally discussed.

Estimation of water table based on geomorphologic and geologic conditions using public database of geotechnical information over Japan

NASA Astrophysics Data System (ADS)

Koshigai, Masaru; Marui, Atsunao

Water table provides important information for the evaluation of groundwater resource. Recently, the estimation of water table in wide area is required for effective evaluation of groundwater resources. However, evaluation process is met with difficulties due to technical and economic constraints. Regression analysis for the prediction of groundwater levels based on geomorphologic and geologic conditions is considered as a reliable tool for the estimation of water table of wide area. Data of groundwater levels were extracted from the public database of geotechnical information. It was observed that changes in groundwater level depend on climate conditions. It was also observed and confirmed that there exist variations of groundwater levels according to geomorphologic and geologic conditions. The objective variable of the regression analysis was groundwater level. And the explanatory variables were elevation and the dummy variable consisting of group number. The constructed regression formula was significant according to the determination coefficients and analysis of the variance. Therefore, combining the regression formula and mesh map, the statistical method to estimate the water table based on geomorphologic and geologic condition for the whole country could be established.

Geomorphology and bank erosion of the Matanuska River, southcentral Alaska

USGS Publications Warehouse

Curran, Janet H.; McTeague, Monica L.

2011-01-01

Bank erosion along the Matanuska River, a braided, glacial river in southcentral Alaska, has damaged or threatened houses, roadways, and public facilities for decades. Mapping of river geomorphology and bank characteristics for a 65-mile study area from the Matanuska Glacier to the river mouth provided erodibility information that was assessed along with 1949-2006 erosion to establish erosion hazard data. Braid plain margins were delineated from 1949, 1962, and 2006 orthophotographs to provide detailed measurements of erosion. Bank material and height and geomorphic features within the Matanuska River valley (primarily terraces and tributary fans) were mapped in a Geographic Information System (GIS) from orthophotographs and field observations to provide categories of erodibility and extent of the erodible corridor. The braid plain expanded 861 acres between 1949 and 2006. Erosion in the highest category ranged from 225 to 1,043 feet at reaches of bank an average of 0.5 mile long, affecting 8 percent of the banks but accounting for 64 percent of the erosion. Correlation of erosion to measurable predictor variables was limited to bank height and material. Streamflow statistics, such as peak streamflow or mean annual streamflow, were not clearly linked to erosion, which can occur during the prolonged period of summer high flows where channels are adjacent to an erodible braid plain margin. The historical braid plain, which includes vegetated braid plain bars and islands and active channels, was identified as the greatest riverine hazard area on the basis of its historical occupation. In 2006, the historical braid plain was an average of 15 years old, as determined from the estimated age of vegetation visible in orthophotographs. Bank erosion hazards at the braid plain margins can be mapped by combining bank material, bank height, and geomorphology data. Bedrock bluffs at least 10 feet high (31 percent of the braid plain margins) present no erosion hazard. At unconsolidated banks (63 percent of the braid plain margins), erosion hazards are great and the distinction in hazards between banks of varying height or geomorphology is slight.

Geomorphology and Tectonics at the Intersection of Silurian and Death Valleys, Southern California - 2005 Guidebook Pacific Cell Friends of the Pleistocene

USGS Publications Warehouse

Miller, David M.; Valin, Zenon C.

2007-01-01

This publication describes results from new regional and detailed surficial geologic mapping, combined with geomorphologic, geochronologic, and tectonic studies, in Silurian Valley and Death Valley, California. The studies address a long-standing problem, the tectonic and geomorphic evolution of the intersection between three regional tectonic provinces: the eastern California shear zone, the Basin and Range region of southern Nevada and adjacent California, and the eastern Mojave Desert region. The chapters represent work presented on the 2005 Friends of the Pleistocene field trip and meeting as well as the field trip road log.

Geomorphology and till architecture of terrestrial palaeo-ice streams of the southwest Laurentide Ice Sheet: A borehole stratigraphic approach

NASA Astrophysics Data System (ADS)

Norris, Sophie L.; Evans, David J. A.; Cofaigh, Colm Ó.

2018-04-01

A multidimensional study, utilising geomorphological mapping and the analysis of regional borehole stratigraphy, is employed to elucidate the regional till architecture of terrestrial palaeo-ice streams relating to the Late Wisconsinan southwest Laurentide Ice Sheet. Detailed mapping over a 57,400 km2 area of southwestern Saskatchewan confirms previous reconstructions of a former southerly flowing ice stream, demarcated by a 800 km long corridor of megaflutes and mega-scale glacial lineations (Ice Stream 1) and cross cut by three, formerly southeast flowing ice streams (Ice Streams 2A, B and C). Analysis of the lithologic and geophysical characteristics of 197 borehole samples within these corridors reveals 17 stratigraphic units comprising multiple tills and associated stratified sediments overlying preglacial deposits, the till thicknesses varying with both topography and distance down corridor. Reconciling this regional till architecture with the surficial geomorphology reveals that surficial units are spatially consistent with a dynamic switch in flow direction, recorded by the cross cutting corridors of Ice Streams 1, 2A, B and C. The general thickening of tills towards lobate ice stream margins is consistent with subglacial deformation theory and variations in this pattern on a more localised scale are attributed to influences of subglacial topography including thickening at buried valley margins, thinning over uplands and thickening in overridden ice-marginal landforms.

Geoscientific Mapping of Vesta by the Dawn Mission

NASA Technical Reports Server (NTRS)

Jaumann, R.; Pieters, C. M.; Neukum, G.; Mottola, S.; DeSanctis, M. C.; Russell, C. T.; Raymond, C. A.; McSween, H. Y.; Roatsch, T.; Nathues, A.;

Impacts of Colville River dynamics on river navigability near Nuiqsut, Alaska: 1955-present

NASA Astrophysics Data System (ADS)

Whitley, M. A.; Panda, S. K.; Prakash, A.; Brinkman, T. J.

2016-12-01

Climate-driven changes in river systems are challenging access to ecosystem services such as access to traditional hunting grounds and other subsistence food sources on the North Slope of Alaska. This work studies the dynamics of the Colville River and assesses the impacts on traditional harvest practices and subsistence travel of the Native community of Nuiqsut. Recent reports from Nuiqsut residents indicate accelerated changes in the environment, limiting river travel and their ability to harvest subsistence food. This study explores how channel migration, gravel bars, and bank erosion have evolved since the 1950s, and their impact on water depth and navigability. In an area of ice-rich permafrost, warmer summer temperatures exacerbate lateral bank erosion, resulting in river siltation. The study focuses on selected key areas south of Nuiqsut that have shown significant change in river geomorphology. Since 1955, some areas proximate to ice wedge exposures show channel migration in excess of 1 km. Panchromatic aerial photography acquired by US Geological Surveys in the mid 1950s, color infrared aerial photography from 1979 and 1982 acquired by the Alaska High Altitude Photography (AHAP) mission, and high resolution satellite images from Digital Globe, Inc. were used in this study. We mapped water, vegetation, and gravel/non-vegetated classes to identify risk areas for river navigability. River bathymetry was also mapped using a multispectral ratio-based water depth retrieval algorithm to identify problem sites for boat travel. Remote sensing products and analyses were validated with field data for mapping risk areas along the river. This study has the potential to be implemented on a larger scale for predictive mapping to aid river navigation. Findings from this study will provide insight whether recent changes are anomalies, or if they are part of a directional trend that will require local adaptation.

Re-examining data-intensive surface water models with high-resolution topography derived from unmanned aerial system photogrammetry

NASA Astrophysics Data System (ADS)

Pai, H.; Tyler, S.

2017-12-01

Small, unmanned aerial systems (sUAS) are quickly becoming a cost-effective and easily deployable tool for high spatial resolution environmental sensing. Land surface studies from sUAS imagery have largely focused on accurate topographic mapping, quantifying geomorphologic changes, and classification/identification of vegetation, sediment, and water quality tracers. In this work, we explore a further application of sUAS-derived topographic mapping to a two-dimensional (2-d), depth-averaged river hydraulic model (Flow and Sediment Transport with Morphological Evolution of Channels, FaSTMECH) along a short, meandering reach of East River, Colorado. On August 8, 2016, we flew a sUAS as part of the Center for Transformative Environmental Monitoring Programs with a consumer-grade visible camera and created a digital elevation map ( 1.5 cm resolution; 5 cm accuracy; 500 m long river corridor) with Agisoft Photoscan software. With the elevation map, we created a longitudinal water surface elevation (WSE) profile by manually delineating the bank-water interface and river bathymetry by applying refraction corrections for more accurate water depth estimates, an area of ongoing research for shallow and clear river systems. We tested both uncorrected and refraction-corrected bathymetries with the steady-state, 2-d model, applying sensitivities for dissipation parameters (bed roughness and eddy characteristics). Model performance was judged from the WSE data and measured stream velocities. While the models converged, performance and insights from model output could be improved with better bed roughness characterization and additional water depth cross-validation for refraction corrections. Overall, this work shows the applicability of sUAS-derived products to a multidimensional river model, where bathymetric data of high resolution and accuracy are key model input requirements.

Geomorphology applied to landscape analysis for planning and management of natural spaces. Case study: Las Batuecas-S. de Francia and Quilamas natural parks, (Salamanca, Spain).

PubMed

Martínez-Graña, A M; Silva, P G; Goy, J L; Elez, J; Valdés, V; Zazo, C

2017-04-15

Geomorphology is fundamental to landscape analysis, as it represents the main parameter that determines the land spatial configuration and facilitates reliefs classification. The goal of this article is the elaboration of thematic maps that enable the determination of different landscape units and elaboration of quality and vulnerability synthetic maps for landscape fragility assessment prior to planning human activities. For two natural spaces, the final synthetic maps were created with direct (visual-perceptual features) and indirect (cartographic models and 3D simulations) methods from thematic maps with GIS technique. This enabled the creation of intrinsic and extrinsic landscape quality maps showing sectors needing most preservation, as well as intrinsic and extrinsic landscape fragility maps (environment response capacity or vulnerability towards human actions). The resulting map shows absorption capacity for areas of maximum and/or minimum human intervention. Sectors of high absorption capacity (minimum need for preservation) are found where the incidence of human intervention is minimum: escarpment bottoms, fitted rivers, sinuous high lands with thick vegetation coverage and valley interiors, or those areas with high landscape quality, low fragility and high absorption capacity, whose average values are found across lower hillsides of some valleys, and sectors with low absorption capacity (areas needing most preservation) found mainly in the inner parts of natural spaces: peaks and upper hillsides, synclines flanks and scattered areas. For the integral analysis of landscape, a mapping methodology has been set. It comprises a valid criterion for rational and sustainable planning, management and protection of natural spaces. Copyright © 2017 Elsevier B.V. All rights reserved.

Geosites and geoheritage representations - a cartographic approach

NASA Astrophysics Data System (ADS)

Rocha, Joao; Brilha, José

2016-04-01

In recent years, the increasing awareness of the importance of nature conservation, particularly towards the protection, conservation and promotion of geological sites, has resulted in a wide range of scientific studies. In a certain way, the majority of geodiversity studies, geoconservation strategies and geosites inventories and geoheritage assessment projects will use, on a particular stage, a cartographic representation - a map - of the most relevant geological and geomorphological features within the area of analyses. A wide range of geosite maps and geological heritage maps have been produced but, so far, a widely accepted conceptual cartographic framework with a specific symbology for cartographic representation has not been created. In this work we debate the lack of a systematic and conceptual framework to support geoheritage and geosite mapping. It is important to create a widely accepted conceptual cartographic framework with a specific symbology to be used within maps dedicated to geoheritage and geosites. We propose a cartographic approach aiming the conceptualization and the definition of a nomenclature and symbology system to be used on both geosite and geoheritage maps. We define a symbology framework for geosite and geoheritage mapping addressed to general public and to secondary school students, in order to be used as geotouristic and didactic tools, respectively. Three different approaches to support the definition of the symbology framework were developed: i) symbols to correlate geosites with the geological time scale; ii) symbols related to each one of the 27 geological frameworks defined in the Portuguese geoheritage inventory; iii) symbols to represent groups of geosites that share common geological and geomorphological features. The use of these different symbols in a map allows a quick understanding of a set of relevant information, in addition to the usual geographical distribution of geosites in a certain area.

The MAP program: building the digital terrain model.

Treesearch

R.H. Twito; R.W. Mifflin; R.J. McGaughey

1987-01-01

PLANS, a software package for integrated timber-harvest planning, uses digital terrain models to provide the topographic data needed to fit harvest and transportation designs to specific terrain. MAP, an integral program in the PLANS package, is used to construct the digital terrain models required by PLANS. MAP establishes digital terrain models using digitizer-traced...

Delineating riparian zones for entire river networks using geomorphological criteria

NASA Astrophysics Data System (ADS)

Fernández, D.; Barquín, J.; Álvarez-Cabria, M.; Peñas, F. J.

2012-03-01

Riparian zone delineation is a central issue for riparian and river ecosystem management, however, criteria used to delineate them are still under debate. The area inundated by a 50-yr flood has been indicated as an optimal hydrological descriptor for riparian areas. This detailed hydrological information is, however, not usually available for entire river corridors, and is only available for populated areas at risk of flooding. One of the requirements for catchment planning is to establish the most appropriate location of zones to conserve or restore riparian buffer strips for whole river networks. This issue could be solved by using geomorphological criteria extracted from Digital Elevation Models. In this work we have explored the adjustment of surfaces developed under two different geomorphological criteria with respect to the flooded area covered by the 50-yr flood, in an attempt to rapidly delineate hydrologically-meaningful riparian zones for entire river networks. The first geomorphological criterion is based on the surface that intersects valley walls at a given number of bankfull depths above the channel (BFDAC), while the second is based on the surface defined by a~threshold value indicating the relative cost of moving from the stream up to the valley, accounting for slope and elevation change (path distance). As the relationship between local geomorphology and 50-yr flood has been suggested to be river-type dependant, we have performed our analyses distinguishing between three river types corresponding with three valley morphologies: open, shallow vee and deep vee valleys (in increasing degree of valley constrainment). Adjustment between the surfaces derived from geomorphological and hydrological criteria has been evaluated using two different methods: one based on exceeding areas (minimum exceeding score) and the other on the similarity among total area values. Both methods have pointed out the same surfaces when looking for those that best match with the 50-yr flood. Results have shown that the BFDAC approach obtains an adjustment slightly better than that of path distance. However, BFDAC requires bankfull depth regional regressions along the considered river network. Results have also confirmed that unconstrained valleys require lower threshold values than constrained valleys when deriving surfaces using geomorphological criteria. Moreover, this study provides: (i) guidance on the selection of the proper geomorphological criterion and associated threshold values, and (ii) an easy calibration framework to evaluate the adjustment with respect to hydrologically-meaningful surfaces.

Mapping seabed geomorphology in the Inner Hebrides, Scotland; Bathymetric records of ice streaming and retreat

NASA Astrophysics Data System (ADS)

Dove, Dayton; Finlayson, Andrew; Bradwell, Tom; Arosio, Riccardo; Howe, John

2014-05-01

Approximately 7,000 km² of new bathymetry have been stitched together with onshore airborne radar data, both gridded at 5m resolution, to map and describe the submarine glacial landscape of the Inner Hebrides sector of the former British-Irish Ice Sheet (BIIS). As part of the MAREMAP Project (http://www.maremap.ac.uk), and to build on previous work (Howe et al., 2012), we are using recently acquired swath bathymetry data, collected primarily by the UKHO Civil Hydrography Programme, to characterise the geomorphology, sea-bed sediments, and bedrock geology of the Inner Hebrides region. Mapping has revealed an extensive array of well-preserved glacigenic landforms on the seabed associated with key stages of ice flow and retreat of the BIIS following the Last Glacial Maximum. On multiple submarine rock platforms and within overdeepened troughs, diverse assemblages of glacially streamlined landforms are present, forming a geomorphic continuum between rock drumlins and mega-flutes. Superimposed streamlined bedforms indicate different phases of fast flow at the ice sheet bed, and the convergence of flow sets suggest that ice sheet flow was organised into faster flowing topographically controlled corridors. Across the region, the streamlined landforms occur within a geographically controlled zone, semi-independent of the underlying geology. This is consistent with the onset zone of the Hebrides Ice Stream, as previously postulated (Howe et al., 2012). Submarine moraine ridges are observed widely across the survey area: within sea lochs, atop rock platforms and superimposed on glacially streamlined bedforms, as well as pinned to topographic highs (i.e. islands). Some retreat patterns reveal clear glacial recession towards respective catchments, while others are more ambiguous and are the focus of ongoing work. The bathymetry data notably reveal more geomorphic evidence of glaciation than adjacent land records, thus providing the opportunity to reassess onshore mapping where clear offshore examples may provide insights into poorly understood terrestrial geological and geomorphological features. And importantly, these new data provide the opportunity to greatly improve offshore geology maps of the region, which are in increasing demand by governmental, commercial, and conservation groups.

Earth Resources Technology Satellite data collection project, ERTS - Bolivia. [thematic mapping

NASA Technical Reports Server (NTRS)

Brockmann, C. E.

1974-01-01

The Earth Resources Technology Satellite program of Bolivia has developed a multidisciplinary project to carry out investigations in cartography and to prepare various thematic maps. In cartography, investigations are being carried out with the ERTS-1 images and with existing maps, to determine their application to the preparation of new cartographic products on one hand and on the other to map those regions where the cartography is still deficient. The application of the MSS images to the geological mapping has given more than satisfactory results. Working with conventional photointerpretation, it has been possible to prepare regional geological maps, tectonic maps, studies relative to mining, geomorphological maps, studies relative to petroleum exploration, volcanological maps and maps of hydrologic basins. In agriculture, the ERTS images are used to study land classification and forest and soils mapping.

Paleoglaciology of the Ala-Archa and Ak-Shyrak areas, Kyrgyz Tian Shan

NASA Astrophysics Data System (ADS)

Blomdin, R.; Beel, C.; Caffee, M. W.; Codilean, A.; Gribenski, N.; Harbor, J.; Heyman, J.; Hattestrand, C.; Ivanov, M.; Kassab, C.; Lifton, N. A.; Petrakov, D.; Rogozhina, I.; Stroeven, A. P.; Usubaliev, R.

2012-12-01

We employed detailed glacial geomorphological mapping of the Ala-Archa and Ak-Shyrak areas, Kyrgyz Tian Shan (Shan = Mountains) to build a paleoglaciological reconstruction. These two areas were selected because their glaciers constitute important freshwater reservoirs for downstream communities (the Kyrgyz capital Bishkek, and cities along the Syr Darja which drains towards the Aral Sea, respectively), and because fluctuations in their extent cause both variations in water supply and risks for glacial hazards. Five landform categories were mapped; glacial valleys, marginal moraines, glacial lineations, hummocky terrain, and melt-water channels. These landforms were mapped using a SRTM digital elevation model (DEM) with a 90 m resolution, Landsat 7 ETM+ satellite imagery with a 30 m resolution, Aster GDEM with a 30 m resolution, and Google Earth. This remotely sensed mapping was also checked and complemented by field mapping. The distribution of mapped landforms indicates restricted glaciations, mainly concentrated to the mountain areas. In both ranges marginal moraines extend beyond the furthest extent of glacial valleys. Furthermore, extensive areas of hummocky moraine in Ak-Shyrak extending beyond montane glacial valleys indicate glacial extents into the intermontane basins. Several series of lateral and terminal moraines in the Ala-Archa and Ak-Shyrak ranges have been identified and sampled for cosmogenic nuclide 10Be dating, while associated glaciofluvial sediment was sampled for optically-stimulated luminescence (OSL) and electron spin resonance (ESR) dating. Future work will involve using these samples to build a consistent chronology for glaciation and investigation of contrasts between paleoglaciological reconstructions of valleys within a single range but with different aspects, as well as between ranges. In the final stages of the project we will use intermediate complexity glacier flow models to examine paleoclimatic implications of the observed spatial and temporal patterns of glacier changes, focused in particular on the last glacial cycle.

Recent transformations in the high-Arctic glacier landsystem Hørbyebreen, Svalbard.

NASA Astrophysics Data System (ADS)

Ewertowski, Marek; Evans, David; Roberts, David; Tomczyk, Aleksandra

2016-04-01

The Hørbyebreen is a polythermal valley glacier in the Petuniabukta area, central part of Spitsbergen. Since the end of the Little Ice Age, a debris-free glacier margin retreated by more than 3 km exposing complex landform assemblages including ice-cored moraines, flutes, eskers and geometric ridge networks. Glacier recession and landforms' development in the terrestrial parts of the foreland were quantified using time-series of orthophotos and digital elevation models (generated based on 1961, 1990, 2009 aerial photographs) and high resolution satellite images from 2013. Additionally, detailed analyses of a case study area were performed based on unmanned aerial vehicle (UAV) imagery (3 cm resolution) captured in 2014. A time-series of 1:5,000 geomorphological maps of the whole foreland, together with 1:300 map of a sample area of complex geometric ridge networks and results of sedimentological analysis, enable us to assess the evolution of glacial landform assemblages. The two main areas of the Hørbyebreen foreland were identified as: (1) the outer moraine ridge and (2) the inner zone between the contemporary ice edge and the outer moraine ridge. The outer moraine ridge was relatively stable and subject to mainly vertical transformation between 1960 and 2009. The most prominent changes were observed within the inner zone. In 1960 it was covered by glacier ice, whereas in 2009 this area exhibited a wide range of subglacial and englacial landforms, including a network of rectilinear ridges which we interpret as crevasse infills created by the injection of pressurized englacial meltwater. Other prominent features in this zone include controlled moraine, indicative of sub-marginal debris entrainment by the polythermal snout, and complex esker network. This landform assemblage is diagnostic of a variable process-form regime in which the glacial geomorphology of polythermal conditions is supplemented with surge signatures and therefore is likely to be the most representative landsystem model for terrestrial-terminating Svalbard glaciers. The research was founded by Polish National Science Centre (project granted by decision number DEC-2011/01/D/ST10/06494).

Lithology and aggregate quality attributes for the digital geologic map of Colorado

USGS Publications Warehouse

Knepper, Daniel H.; Green, Gregory N.; Langer, William H.

1999-01-01

This geologic map was prepared as a part of a study of digital methods and techniques as applied to complex geologic maps. The geologic map was digitized from the original scribe sheets used to prepare the published Geologic Map of Colorado (Tweto 1979). Consequently the digital version is at 1:500,000 scale using the Lambert Conformal Conic map projection parameters of the state base map. Stable base contact prints of the scribe sheets were scanned on a Tektronix 4991 digital scanner. The scanner automatically converts the scanned image to an ASCII vector format. These vectors were transferred to a VAX minicomputer, where they were then loaded into ARC/INFO. Each vector and polygon was given attributes derived from the original 1979 geologic map.

Citizen-Scientist Digitization of a Complex Geologic Map of the McDowell Mountains (Scottsdale, Arizona).

NASA Astrophysics Data System (ADS)

Gruber, D.; Skotnicki, S.; Gootee, B.

2016-12-01

The work of citizen scientists has become very important to researchers doing field work and internet-based projects but has not been widely utilized in digital mapping. The McDowell Mountains - located in Scottsdale, Arizona, at the edge of the basin-and-range province and protected as part of the McDowell Sonoran Preserve - are geologically complex. Until recently, no comprehensive geologic survey of the entire range had been done. Over the last 9 years geologist Steven Skotnicki spent 2000 hours mapping the complex geology of the range. His work, born of personal interest and partially supported by the McDowell Sonoran Conservancy, resulted in highly detailed hand-drawn survey maps. Dr. Skotnicki's work provides important new information and raises interesting research questions about the geology of this range. Citizen scientists of the McDowell Sonoran Conservancy Field Institute digitized Dr. Skotnicki's maps. A team of 10 volunteers, trained in ArcMap digitization techniques and led by volunteer project leader Daniel Gruber, performed the digitization work. Technical oversight of mapping using ArcMap, including provision of USGS-based mapping toolbars, was provided by Arizona Geological Survey (AZGS) research geologist Brian Gootee. The map digitization process identified and helped resolve a number of mapping questions. The citizen-scientist team spent 900 hours on training, digitization, quality checking, and project coordination with support and review by Skotnicki and Gootee. The resulting digital map has approximately 3000 polygons, 3000 points, and 86 map units with complete metadata and unit descriptions. The finished map is available online through AZGS and can be accessed in the field on mobile devices. User location is shown on the map and metadata can be viewed with a tap. The citizen scientist map digitization team has made this important geologic information available to the public and accessible to other researchers quickly and efficiently.

Railway deformation detected by DInSAR over active sinkholes in the Ebro Valley evaporite karst, Spain

NASA Astrophysics Data System (ADS)

Galve, J. P.; Castañeda, C.; Gutiérrez, F.

2015-06-01

Previously not measured subsidence on railway tracks was detected using DInSAR displacement maps produced for the central sector of Ebro Valley (NE Spain). This area is affected by evaporite karst and the analyzed railway corridors traverse active sinkholes that produce deformations in these infrastructures. One of the railway tracks affected by slight settlements corresponds to the Madrid-Barcelona high-speed line, a transport infrastructure highly vulnerable to ground deformation processes. Our analysis based on DInSAR measurements and geomorphological surveys indicate that this line show dissolution-induced subsidence and compaction of anthropogenic deposits (infills and embankments). By using DInSAR techniques, it was also measured the significant subsidence related to the activity of sinkholes in the Castejón-Zaragoza conventional railway line. Thus, this study demonstrate that DInSAR velocity maps coupled with detailed geomorphological surveys may help in the identification of the sectors of railway tracks that may compromise the safety of travellers.

Reconnaissance investigation of the alluvial gold deposits in the North Takhar Area of Interest, Takhar Province, Afghanistan

USGS Publications Warehouse

Chirico, Peter G.; Malpeli, Katherine C.; Moran, Thomas W.

2013-01-01

This study is a reconnaissance assessment of the alluvial gold deposits of the North Takhar Area of Interest (AOI) in Takhar Province, Afghanistan. Soviet and Afghan geologists collected data and calculated the gold deposit reserves in Takhar Province in the 1970s, prior to the development of satellite-based remote-sensing platforms and new methods of geomorphic mapping. The purpose of this study was to integrate new mapping techniques with previously collected borehole sampling and concentration sampling data and geomorphologic interpretations to reassess the alluvial gold placer deposits in the North Takhar AOI. Through a combination of historical borehole and cross-section data and digital terrain modeling, the Samti, Nooraba-Khasar-Anjir, and Kocha River placer deposits were reassessed. Resource estimates were calculated to be 20,927 kilograms (kg) for Samti, 7,626 kg for Nooraba-Khasar-Anjir, 160 kg for the mouth of the Kocha, 1,047 kg for the lower Kocha, 113 kg for the middle Kocha, and 168 kg for the upper Kocha. Previous resource estimates conducted by the Soviets for the Samti and Nooraba-Khasar-Anjir deposits estimated 30,062 kg and 802 kg of gold, respectively. This difference between the new estimates and previous estimates results from the higher resolution geomorphic model and the interpretation of areas outside of the initial work zone studied by Soviet and Afghan geologists.

Seafloor mapping and benthic habitat GIS for southern California, volume III

USGS Publications Warehouse

Cochrane, Guy R.; Golden, Nadine E.; Dartnell, Pete; Schroeder, Donna M.; Finlayson, David P.

2007-01-01

From August 8-27, 2005, more than 75 km of the continental shelf (Fig. 1) in water depths of 20-70m southeast of Santa Barbara, were surveyed during the USGS cruise S-1-05-SC (http://walrus.wr.usgs.gov/infobank/s/s105sc/html/s-1-05-sc.meta.html). Both Interferometric sonar and 14 hours of both vertical and oblique georeferenced submarine digital video were collected to (1) obtain geophysical data (bathymetry and acoustic reflectance), (2) examine and record geologic characteristics of the sea floor, and (3) construct maps of seafloor geomorphology and habitat distribution. Substrate distribution is predicted using a modified version of Cochrane and Lafferty (2002) video-supervised statistical classification of sonar data that includes derivatives of bathymetry data. Specific details of the methods can be found in the meatadata of the bathymetry data file. Substrates observed are predominantly sand with some rock. Rocky substrates were restricted primarily to an east-west trending bathymetric high 2,000 m north of oil platforms. This is an updated report (version 2.0) from the earlier 2007-1271 (version 1.0) open-file report. This updated report re-releases the data files in UTM, zone 11, WGS84 coordinates. Also, the bathymetry data has been corrected for a vertical offset discovered in the earlier 2007-1271 (version 1.0) report.

Reconnaissance investigation of the placer gold deposits in the Zarkashan Area of Interest, Ghazni Province, Afghanistan

USGS Publications Warehouse

Malpeli, Katherine C.; Chirico, Peter G.; McLoughlin, Isabel H.

2013-01-01

This study is a reconnaissance investigation of the placer gold deposits in the Zarkashan Area of Interest (AOI) in Ghazni Province, Afghanistan. Detailed investigations of the Zarkashan gold deposits were conducted by Soviet and Afghan geologists in the 1960s and 1970s, prior to the development of satellite-based remote-sensing platforms and new methods of geomorphic mapping. The purpose of this study was to integrate new mapping techniques with previously collected concentration and borehole sampling data and geomorphologic interpretations to reassess the placer gold deposits in the Zarkashan AOI. A methodology combining the collection and analysis of historical sampling data, digital database development, hydrologic analysis, and geomorphic modeling was used. The analysis led to the reinterpretation of four gold-bearing seams along the Zarkashan River, and the calculation of an estimated gold reserve of approximately 3,000 kilograms (kg). This estimate is approximately 1,500 kg greater than the Soviet estimate. The result differs in large part due to the reinterpretation of the seams based on a much lower cutoff grade of 100 mg/m3. Because cutoff grade is dependent in part on the price of gold, the sevenfold increase in the price of gold since the undertaking of the Soviet investigation warranted our re-evaluation of their 500 mg/m3 cutoff grade.

Reducing the Dynamical Degradation by Bi-Coupling Digital Chaotic Maps

NASA Astrophysics Data System (ADS)

Liu, Lingfeng; Liu, Bocheng; Hu, Hanping; Miao, Suoxia

A chaotic map which is realized on a computer will suffer dynamical degradation. Here, a coupled chaotic model is proposed to reduce the dynamical degradation. In this model, the state variable of one digital chaotic map is used to control the parameter of the other digital map. This coupled model is universal and can be used for all chaotic maps. In this paper, two coupled models (one is coupled by two logistic maps, the other is coupled by Chebyshev map and Baker map) are performed, and the numerical experiments show that the performances of these two coupled chaotic maps are greatly improved. Furthermore, a simple pseudorandom bit generator (PRBG) based on coupled digital logistic maps is proposed as an application for our method.

Scoping of Flood Hazard Mapping Needs for Merrimack County, New Hampshire

DTIC Science & Technology

2006-01-01

DOQ Digital Orthophoto Quadrangle DOQQ Digital Ortho Quarter Quadrangle DTM Digital Terrain Model FBFM Flood Boundary and Floodway Map FEMA Federal...discussed available data and coverages within New Hampshire (for example, 2003 National Agriculture Imag- ery Program (NAIP) color Digital Orthophoto ... orthophotos providing improved base map accuracy. NH GRANIT is presently converting the standard, paper FIRMs and Flood Boundary and Floodway maps (FBFMs

Landslides Identification Using Airborne Laser Scanning Data Derived Topographic Terrain Attributes and Support Vector Machine Classification

NASA Astrophysics Data System (ADS)

Pawłuszek, Kamila; Borkowski, Andrzej

2016-06-01

Since the availability of high-resolution Airborne Laser Scanning (ALS) data, substantial progress in geomorphological research, especially in landslide analysis, has been carried out. First and second order derivatives of Digital Terrain Model (DTM) have become a popular and powerful tool in landslide inventory mapping. Nevertheless, an automatic landslide mapping based on sophisticated classifiers including Support Vector Machine (SVM), Artificial Neural Network or Random Forests is often computationally time consuming. The objective of this research is to deeply explore topographic information provided by ALS data and overcome computational time limitation. For this reason, an extended set of topographic features and the Principal Component Analysis (PCA) were used to reduce redundant information. The proposed novel approach was tested on a susceptible area affected by more than 50 landslides located on Rożnów Lake in Carpathian Mountains, Poland. The initial seven PCA components with 90% of the total variability in the original topographic attributes were used for SVM classification. Comparing results with landslide inventory map, the average user's accuracy (UA), producer's accuracy (PA), and overall accuracy (OA) were calculated for two models according to the classification results. Thereby, for the PCA-feature-reduced model UA, PA, and OA were found to be 72%, 76%, and 72%, respectively. Similarly, UA, PA, and OA in the non-reduced original topographic model, was 74%, 77% and 74%, respectively. Using the initial seven PCA components instead of the twenty original topographic attributes does not significantly change identification accuracy but reduce computational time.

Spatial digital database of the geologic map of Catalina Core Complex and San Pedro Trough, Pima, Pinal, Gila, Graham, and Cochise counties, Arizona

USGS Publications Warehouse

Dickinson, William R.; digital database by Hirschberg, Douglas M.; Pitts, G. Stephen; Bolm, Karen S.

2002-01-01

The geologic map of Catalina Core Complex and San Pedro Trough by Dickinson (1992) was digitized for input into a geographic information system (GIS) by the U.S. Geological Survey staff and contractors in 2000-2001. This digital geospatial database is one of many being created by the U.S. Geological Survey as an ongoing effort to provide geologic information in a geographic information system (GIS) for use in spatial analysis. The resulting digital geologic map database data can be queried in many ways to produce a variety of geologic maps and derivative products. Digital base map data (topography, roads, towns, rivers, lakes, and so forth) are not included; they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:125,000 (for example, 1:100,000 or 1:24,000). The digital geologic map plot files that are provided herein are representations of the database. The map area is located in southern Arizona. This report lists the geologic map units, the methods used to convert the geologic map data into a digital format, the ArcInfo GIS file structures and relationships, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet. The manuscript and digital data review by Lorre Moyer (USGS) is greatly appreciated.

Tri-stereo Pleiades images-derived digital surface models for tectonic geomorphology studies

NASA Astrophysics Data System (ADS)

Ferry, Matthieu; Le Roux-Mallouf, Romain; Ritz, Jean-François; Berthet, Théo; Peyret, Michel; Vernant, Philippe; Maréchal, Anaïs; Cattin, Rodolphe; Mazzotti, Stéphane; Poujol, Antoine

2014-05-01

Very high resolution digital elevation models are a key component of modern quantitative geomorphology. In parallel to high-precision but time-consuming kinematic GPS and/or total station surveys and dense coverage but expensive LiDAR campaigns, we explore the usability of affordable, flexible, wide coverage digital surface models (DSMs) derived from Pleiades tri-stereo optical images. We present two different approaches to extract DSM from a triplet of images. The first relies on the photogrammetric extraction of 3 DSMs from the 3 possible stereo couples and subsequent merge based on the best correlation score. The second takes advantage of simultaneous correlation over the 3 images to derive a point cloud. We further extract DSM from panchromatic 0.5 m resolution images and multispectral 2 m resolution images to test for correlation and noise and determine optimal correlation window size and achievable resolution. Georeferencing is also assessed by comparing raw coordinates derived from Pleiades Rational Polynomial Coefficients to ground control points. Primary images appear to be referenced within ~15 m over flat areas where parallax is minimal while derived DSMs and associated orthorectified images show a much improved referencing within ~5 m of GCPs. In order to assess the adequacy of Pleiades DSMs for tectonic geomorphology, we present examples from case studies along the Trougout normal fault (Morocco), the Hovd strike-slip fault (Mongolia), the Denali strike-slip fault (USA and Canada) and the Main Frontal Thrust (Bhutan). In addition to proposing a variety of tectonic contexts, these examples cover a wide range of climatic conditions (semi-arid, arctic and tropical), vegetation covers (bare earth, sparse Mediterranean, homogeneous arctic pine, varied tropical forest), lithological natures and related erosion rates. The capacity of derived DSMs is demonstrated to characterize geomorphic markers of active deformation such as marine and alluvial terraces, stream gullies, alluvial fans and fluvio-glacial deposits in terms of vertical (from DSMs) and horizontal (from orthorectified optical images) offsets. Values extracted from Pleiades DSMs compare well to field measurements in terms of relief and slope, which suggests effort and resources necessary for field topography could be significantly reduced, especially in poorly accessible areas.

Preliminary geologic map of the Piru 7.5' quadrangle, southern California: a digital database

USGS Publications Warehouse

Yerkes, R.F.; Campbell, Russell H.

1995-01-01

This Open-File report is a digital geologic map database. This pamphlet serves to introduce and describe the digital data. There is no paper map included in the Open-File report. This digital map database is compiled from previously published sources combined with some new mapping and modifications in nomenclature. The geologic map database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U. S. Geological Survey. For detailed descriptions of the units, their stratigraphic relations and sources of geologic mapping consult Yerkes and Campbell (1995). More specific information about the units may be available in the original sources.

Geologic Map of the Utukok River Quadrangle, Alaska

USGS Publications Warehouse

Mull, Charles G.; Houseknecht, David W.; Pessel, G.H.; Garrity, Christopher P.

2006-01-01

This map is a product of the USGS Digital Geologic Maps of Northern Alaska project, which captures in digital format quadrangles across the entire width of northern Alaska. Sources include geologic maps previously published in hardcopy format and recent updates and revisions based on field mapping by the Alaska Department of Natural Resources, Division of Geological and Geophysical Surveys and Division of Oil and Gas, and the U.S. Geological Survey. Individual quadrangles are digitized at either 1:125,000 or 1:250,000 depending on the resolution of source maps. The project objective is to produce a set of digital geologic maps with uniform stratigraphic nomenclature and structural annotation, and publish those maps electronically.

A Mid-Latitude Geomorphologic Map of Titan

NASA Astrophysics Data System (ADS)

Lopes, Rosaly M. C.; Malaska, Michael; Schoenfeld, Ashley; Solomonidou, Anezina; Birch, Samuel; Hayes, Alexander; Williams, David A.; Janssen, Michael A.; Le Gall, Alice; Turtle, Elizabeth P.; Radebaugh, Jani; Cassini RADAR Team

2016-10-01

We investigated the geologic history of Titan through mapping and analyzing the distribution of observed geomorphic features using a combination of Cassini data collected by RADAR, VIMS, and ISS. Determining the spatial and superposition relationships between geomorphologic units on Titan leads to an understanding of the likely time evolution of the landscape and gives insight into the process interactions that drive its evolution. We have used all available datasets to extend the mapping initially done by Lopes et al. [1]. We now have the mid-latitudes (60N to 60S) of Titan mapped at 1:800,000 scale in all areas covered by Synthetic Aperture Radar (SAR). A map of the polar regions has been done by Birch et al. [2]. For the mid-latitudes, we have defined five broad classes of terrains following Malaska et al. [3], largely based on prior mapping [1]. These broad classes are: craters, hummocky/mountainous, labyrinth, plains, and dunes. We have found that the hummocky/mountainous terrains are the oldest units on the surface and appear radiometrically cold, indicating icy materials [5]. Dunes are the youngest units and appear radiometrically warm, indicating organic sediments. VIMS analysis shows that compositional variations can also exist within the same class of unit [6, 7]. Future work aims to combine the polar maps of Birch et al. [2] with the mid-latitude maps presented here and harmonize the units at the 60 degrees boundaries. We also plan to extend the map in regions not covered by SAR to produce a 1:1,500,000 scale map compatible with USGS standards.References: [1] Lopes, R.M.C., et al.: Icarus, 205, 540-588, 2010; [2] Birch et al., submitted to Icarus. [3] Malaska, M., et al.: Icarus, 270, 130-161, 2016; [4] Barnes, J., et al.: Pl. Scie., 2:1, 2013; [5] Janssen et al., 2016 Icarus 270, 443-459, 2016. [6] Solomonidou, A., et al. : DPS abstract, 2016. [7] Lopes, R.M.C., et al, Icarus, 270, 162-182, 2016.

Spatial digital database for the tectonic map of Southeast Arizona

USGS Publications Warehouse

map by Drewes, Harald; digital database by Fields, Robert A.; Hirschberg, Douglas M.; Bolm, Karen S.

2002-01-01

A spatial database was created for Drewes' (1980) tectonic map of southeast Arizona: this database supercedes Drewes and others (2001, ver. 1.0). Staff and a contractor at the U.S. Geological Survey in Tucson, Arizona completed an interim digital geologic map database for the east part of the map in 2001, made revisions to the previously released digital data for the west part of the map (Drewes and others, 2001, ver. 1.0), merged data files for the east and west parts, and added additional data not previously captured. Digital base map data files (such as topography, roads, towns, rivers and lakes) are not included: they may be obtained from a variety of commercial and government sources. This digital geospatial database is one of many being created by the U.S. Geological Survey as an ongoing effort to provide geologic information in a geographic information system (GIS) for use in spatial analysis. The resulting digital geologic map database can be queried in many ways to produce a variety of geologic maps and derivative products. Because Drewes' (1980) map sheets include additional text and graphics that were not included in this report, scanned images of his maps (i1109_e.jpg, i1109_w.jpg) are included as a courtesy to the reader. This database should not be used or displayed at any scale larger than 1:125,000 (for example, 1:100,000 or 1:24,000). The digital geologic map plot files (i1109_e.pdf and i1109_w.pdf) that are provided herein are representations of the database (see Appendix A). The map area is located in southeastern Arizona (fig. 1). This report describes the map units (from Drewes, 1980), the methods used to convert the geologic map data into a digital format, the ArcInfo GIS file structures and relationships, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet. The manuscript and digital data review by Helen Kayser (Information Systems Support, Inc.) is greatly appreciated.

Preliminary digital geologic maps of the Mariposa, Kingman, Trona, and Death Valley Sheets, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

D`Agnese, F.A.; Faunt, C.C.; Turner, A.K.

1995-10-01

Parts of four 1:250,000-scale geologic maps by the California Department of Natural Resources, Division of Mines and Geology have been digitized for use in hydrogeologic characterization. These maps include the area of California between lat. 35{degree}N; Long. 115{degree}W and lat. 38{degree}N, long. 118{degree}W of the Kingman Sheet (Jennings, 1961), Trona Sheet (Jennings and others, 1962), Mariposa Sheet (Strand, 1967), and Death Valley Sheet (Streitz and Stinson, 1974). These digital maps are being released by the US Geological Survey in the ARC/INFO Version 6.1 Export format. The digitized data include geologic unit boundaries, fault traces, and identity of geologic units. Themore » procedure outlined in US Geological Survey Circular 1054 (Soller and others, 1990) was sued during the map construction. The procedure involves transferring hard-copy data into digital format by scanning manuscript maps, manipulating the digital map data, and outputting the data. Most of the work was done using Environmental Systems Research Institute`s ARC/INFO software. The digital maps are available in ARC/INFO Rev. 6.1 Export format, from the USGS, Yucca Mountain Project, in Denver, Colorado.« less

First-order shallow aquifer characteristics across Europe: The International Hydrogeological Map of Europe at scale 1:1.5 Million (IHME1500)

NASA Astrophysics Data System (ADS)

Günther, Andreas; Duscher, Klaus; Broda, Stefan; Clos, Patrick; Reichling, Jörg

2017-04-01

Since the mid of the last century, pan-European hydrogeological overview-mapping is conducted at the scale 1 : 1.5 Million following common standards and guidelines to interpret suitable geologic mapping units in terms of potential uppermost aquifer (or non-aquifer) characteristics. These comprises potential aquifer productivities and general hydrogeological aquifer conditions (fissured vs. porous). The printed IHME1500 dataset successively elaborated and published from 1970 - 2013 consists of 25 individual map sheets. Besides the potential aquifer characterization grouped in six classes, IHME1500 offers a complete coverage of lithological material properties of potential shallow aquifer assemblages, and tracelines of major fault structures. Regional information on groundwater surfaces, aquifer thicknesses and depths, locations and characteristics of groundwater springs and other punctual information related to European groundwater resources is present for some areas in selected map sheets, however not digitally available. Synoptic IHME1500 vector data consists of a topographically corrected, seamless and harmonized polygon layer with attribute information on potential aquifer productivity and lithology. While the standardized aquifer-classification is relatively easy to harmonize across the entire mapped area, the lithological information of IHME1500 is presented using sheet-specific legend information resulting in more than 1000 aquifer lithology classes. An attempt was made to harmonize this information utilizing a specifically developed taxonomic scheme, treating consolidated, partly consolidated and unconsolidated materials separately. The translation of the original lithological information into this scheme allows for a hierarchical grouping of the mapping units into five generalization levels, where the highest aggregation level displays a ternary map showing the distribution of consolidated, partially consolidated and unconsolidated aquifer materials. The harmonized and hierarchically structured IHME1500 information based on the published map sheet data also allows for the extension of the mapped area in regions where only incomplete, unpublished IHME1500 draft information is available. IHME1500 now covers the entire European continent up to the Urals, the Caucasus region, and parts of the Middle East (Turkey, Cyprus, parts of Syria and Iraq). IHME1500 represents the only digitally available coherent overview information on potential groundwater resources and shallow aquifer characteristics across Europe. The data is therefore of great use for European policy support in terms of e.g. transboundary aquifer identification and characterization, the harmonization of regional European groundwater bodies, and the delineation of hot spot regions for aquifer systems under potential environmental stress with respect to climate change, natural hazards or migratory flows. Additionally, the lithological information of IHME1500 represents the only harmonized pan-European dataset on shallow subsurface geologic materials available and can used for the spatial delineation of soil parent materials and as a spatial predictor for the evaluation of geomorphological hazards at overview scales. IHME1500 GIS data can be downloaded through BGŔs product centre (http://produktcenter.bgr.de).

Cartography of irregularly shaped satellites

NASA Technical Reports Server (NTRS)

Batson, R. M.; Edwards, Kathleen

1987-01-01

Irregularly shaped satellites, such as Phobos and Amalthea, do not lend themselves to mapping by conventional methods because mathematical projections of their surfaces fail to convey an accurate visual impression of the landforms, and because large and irregular scale changes make their features difficult to measure on maps. A digital mapping technique has therefore been developed by which maps are compiled from digital topographic and spacecraft image files. The digital file is geometrically transformed as desired for human viewing, either on video screens or on hard copy. Digital files of this kind consist of digital images superimposed on another digital file representing the three-dimensional form of a body.

The Twenty-Fifth Lunar and Planetary Science Conference. Part 2: H-O

NASA Technical Reports Server (NTRS)

1994-01-01

Various papers on lunar and planetary science are presented, covering such topics as: planetary geology, lunar geology, meteorites, shock loads, cometary collisions, planetary mapping, planetary atmospheres, chondrites, chondrules, planetary surfaces, impact craters, lava flow, achondrites, geochemistry, stratigraphy, micrometeorites, tectonics, mineralogy, petrology, geomorphology, and volcanology.

Ecological units of the Northern Region: Subsections

Treesearch

John A. Nesser; Gary L. Ford; C. Lee Maynard; Debbie Dumroese

1997-01-01

Ecological units are described at the subsection level of the Forest Service National Hierarchical Framework of Ecological Units. A total of 91 subsections are delineated on the 1996 map "Ecological Units of the Northern Region: Subsections," based on physical and biological criteria. This document consists of descriptions of the climate, geomorphology,...

EFFECT OF GEOMORPHOLOGIC RESOLUTION ON MODELING OF RUNOFF HYDROGRAPH AND SEDIMENTOGRAPH OVER SMALL WATERSHEDS

EPA Science Inventory

In hydrologic models GIS interfaces are commonly used for extracting the channel network, and delineating the watershed. By overlaying soil and land use maps onto the extracted channel network, input files required by the model are prepared. However, the nature of the extracted c...

Enhanced digital mapping project : final report

DOT National Transportation Integrated Search

2004-11-19

The Enhanced Digital Map Project (EDMap) was a three-year effort launched in April 2001 to develop a range of digital map database enhancements that enable or improve the performance of driver assistance systems currently under development or conside...

Rockfall trajectory modelling by the integration of Digital Terrestrial Photogrammetry, Laser Scanning and GIS

NASA Astrophysics Data System (ADS)

Francioni, Mirko; Salvini, Riccardo; Riccucci, Silvia; Guastaldi, Enrico; Ortolano, Fabrizio; Bonciani, Filippo; Callegari, Ivan; Fantozzi, Pierlorenzo

2010-05-01

The present paper describes the runout analysis of rocky unstable blocks on the slope, 500 m wide and 600 m high, overhanging the railroad line Domodossola - Iselle, Italy. In addition to the traditional geological, geomorphological and engineering-geological surveys, DTP (Digital Terrestrial Photogrammetry) by means of an helicopter was used to perform a detailed analysis of rocky blocks sited in inaccessible areas. In order to accomplish the analysis, DTP was combined with LS (Laser Scanning) to build the DDSM (Digital Dense Surface Model) of the slope. Aim of the work is the assessment of the rockfalls potentially dangerous for the railroad line, the assessment of the efficiency of existing protection measures and the prompt of mitigation strategies and monitoring. In order to collect the exact position and size of blocks and wedges, a digital interpretation of stereopairs coming from DTP has been carried out. The photointerpretation has been used to realize the land cover map (ex. outcropping rock, soil covered by vegetation) and to recognize the mitigation and protection measures already installed. Starting from blocks position the DDSM has allowed to determine the probable trajectories of rockfall along the slope. These have been calculated by means of a GIS procedure by the use of the ArcHydro module of EsriTM ArcMap assuming a correspondence between probable trajectories and flowdirection. The morphologic profile of rock falling paths has been obtained by the interpolation of 3D points coming from a properly procedure developed inside EsriTM Arcinfo Workstation environment integrated with the Easy Profiler tool of EsriTM ArcMap. The physical-mechanical characteristics of blocks, the morphologic profile, the land cover and the location of the protection barriers (classified according to the height - from 2 to 4 m - and to the preservation status), have been used as input data in RocFall2D (RoscienceTM) software to calculate the runout analysis. Local slope land cover has been managed by a statistical approach utilizing the coefficient of normal and tangential restitution; in this way probabilistic results about rockfall end point and kinetic energy along the falling path and on the barriers have been obtained. Considering the railroad line proximity, the analysis has shown the high probability to reach the train track for some unstable block. Some other ends their fall mainly in correspondence of vegetated and less steep areas; the remaining blocks are stopped by the existing protection measures. Results from this work have allowed the hazard zoning in respect to the railway; moreover, comparing them with results coming from the rock slope stability analysis, it has been possible to suggest the proper protection methods in different areas.

Spatial Digital Database for the Geologic Map of Oregon

USGS Publications Warehouse

Walker, George W.; MacLeod, Norman S.; Miller, Robert J.; Raines, Gary L.; Connors, Katherine A.

2003-01-01

Introduction This report describes and makes available a geologic digital spatial database (orgeo) representing the geologic map of Oregon (Walker and MacLeod, 1991). The original paper publication was printed as a single map sheet at a scale of 1:500,000, accompanied by a second sheet containing map unit descriptions and ancillary data. A digital version of the Walker and MacLeod (1991) map was included in Raines and others (1996). The dataset provided by this open-file report supersedes the earlier published digital version (Raines and others, 1996). This digital spatial database is one of many being created by the U.S. Geological Survey as an ongoing effort to provide geologic information for use in spatial analysis in a geographic information system (GIS). This database can be queried in many ways to produce a variety of geologic maps. This database is not meant to be used or displayed at any scale larger than 1:500,000 (for example, 1:100,000). This report describes the methods used to convert the geologic map data into a digital format, describes the ArcInfo GIS file structures and relationships, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet. Scanned images of the printed map (Walker and MacLeod, 1991), their correlation of map units, and their explanation of map symbols are also available for download.

Geologic Map of the Point Lay Quadrangle, Alaska

USGS Publications Warehouse

Mull, Charles G.; Houseknecht, David W.; Pessel, G.H.; Garrity, Christopher P.

2008-01-01

This map is a product of the USGS Digital Geologic Maps of Northern Alaska project, which captures in digital format quadrangles across the entire width of northern Alaska. Sources include geologic maps previously published in hardcopy format and recent updates and revisions based on field mapping by the Alaska Department of Natural Resources, Division of Geological and Geophysical Surveys and Division of Oil and Gas, and the U.S. Geological Survey. Individual quadrangles are digitized at either 1:125,000 or 1:250,000 depending on the resolution of source maps. The project objective is to produce a set of digital geologic maps with uniform stratigraphic nomenclature and structural annotation, and publish those maps electronically. The paper version of this map is available for purchase from the USGS Store.

Geologic Map of the Ikpikpuk River Quadrangle, Alaska

USGS Publications Warehouse

Mull, Charles G.; Houseknecht, David W.; Pessel, G.H.; Garrity, Christopher P.

2005-01-01

This map is a product of the USGS Digital Geologic Maps of Northern Alaska project, which captures in digital format quadrangles across the entire width of northern Alaska. Sources include geologic maps previously published in hardcopy format and recent updates and revisions based on field mapping by the Alaska Department of Natural Resources, Division of Geological and Geophysical Surveys and Division of Oil and Gas, and the U.S. Geological Survey. Individual quadrangles are digitized at either 1:125,000 or 1:250,000 depending on the resolution of source maps. The project objective is to produce a set of digital geologic maps with uniform stratigraphic nomenclature and structural annotation, and publish those maps electronically. The paper version of this map is available for purchase from the USGS Store.

Geologic Map of the Lookout Ridge Quadrangle, Alaska

USGS Publications Warehouse

Mull, Charles G.; Houseknecht, David W.; Pessel, G.H.; Garrity, Christopher P.

2006-01-01

This map is a product of the USGS Digital Geologic Maps of Northern Alaska project, which captures in digital format quadrangles across the entire width of northern Alaska. Sources include geologic maps previously published in hardcopy format and recent updates and revisions based on field mapping by the Alaska Department of Natural Resources, Division of Geological and Geophysical Surveys and Division of Oil and Gas, and the U.S. Geological Survey. Individual quadrangles are digitized at either 1:125,000 or 1:250,000 depending on the resolution of source maps. The project objective is to produce a set of digital geologic maps with uniform stratigraphic nomenclature and structural annotation, and publish those maps electronically. The paper version of this map is available for purchase from the USGS Store.

TRENDS IN ENGINEERING GEOLOGIC AND RELATED MAPPING.

USGS Publications Warehouse

Varnes, David J.; Keaton, Jeffrey R.

1983-01-01

Progress is reviewed that has been made during the period 1972-1982 in producing medium- and small-scale engineering geologic maps with a variety of content. Improved methods to obtain and present information are evolving. Standards concerning text and map content, soil and rock classification, and map symbols have been proposed. Application of geomorphological techniques in terrain evaluation has increased, as has the use of aerial photography and other remote sensing. Computers are being used to store, analyze, retrieve, and print both text and map information. Development of offshore resources, especially petroleum, has led to marked improvement and growth in marine engineering geology and geotechnology. Coordinated planning for societal needs has required broader scope and increased complexity of both engineering geologic and environmental geologic studies. Refs.

Insights into bird wing evolution and digit specification from polarizing region fate maps.

PubMed

Towers, Matthew; Signolet, Jason; Sherman, Adrian; Sang, Helen; Tickle, Cheryll

2011-08-09

The proposal that birds descended from theropod dinosaurs with digits 2, 3 and 4 was recently given support by short-term fate maps, suggesting that the chick wing polarizing region-a group that Sonic hedgehog-expressing cells-gives rise to digit 4. Here we show using long-term fate maps that Green fluorescent protein-expressing chick wing polarizing region grafts contribute only to soft tissues along the posterior margin of digit 4, supporting fossil data that birds descended from theropods that had digits 1, 2 and 3. In contrast, digit IV of the chick leg with four digits (I-IV) arises from the polarizing region. To determine how digit identity is specified over time, we inhibited Sonic hedgehog signalling. Fate maps show that polarizing region and adjacent cells are specified in parallel through a series of anterior to posterior digit fates-a process of digit specification that we suggest is involved in patterning all vertebrate limbs with more than three digits.

"Parco Archeologico Storico Naturale delle Chiese Rupestri del Materano": geomorphological fragility and slope instability in a rupestrian-heritage rich area (Basilicata, south Italy).

NASA Astrophysics Data System (ADS)

Francioso, R.; Sdao, F.; Tropeano, M.

2003-04-01

The Italian Ministry of Education, University and Research financed a research project about the study and the control of hydrogeological hazard of some sites belonging to the "Parco Archeologico Storico Naturale delle Chiese Rupestri del Materano"; the Park and the old city of Matera ("Sassi di Matera") was inserted in the UNESCO World Heritage list since 1993. The studied sites ("Belvedere Chiese Rupestri" and "Iazzo dell'Ofra" localities) are located along the top of the walls of the deep canyon (locally called "Gravina di Matera" and deeper than 100 m) which characterizes the area. Several valuable medieval rupestrian hand-hewn rock churches and sanctuaries are present along the canyon walls. The canyon cut weak rocks (Plio-Pleistocene calcarenites, in which churches and sanctuaries are excavated) and the underlying well-stratified limestones (Cretaceous calcilutites). Both rocks are abundantly and strongly fractured and disjointed by several different joint sets, and, on the left wall of the "Gravina di Matera" canyon, they are characterized by a mainly dipping-slope attitude. Consequently, rock blocks of different sizes formed (up to some tens of m^3 in volume), and are characterized by low stability condition. The considerable acclivity of the walls and the defects and intense fracturing state of rocks, especially along the edge, cause rapid falls, topples and rockslides of the blocks. This geomorphological fragility, confirmed by wide-spread signs of potential instability and by several rock blocks fell in the stream, causes the diffuse and significant structural-failures processes that involve most of the very fine rupestrian heritages. Our study, after the geological and geomorphological description of the sites and the editing of thematic maps, concentrates on the determination the present-day slope instability conditions. Moreover, the study demonstrated the notable genetic relationship between jointing, slope instability and failure type of carbonate blocks. The main results of this geological and geomorphological studies and thematic maps will be reported and discussed.

The geomorphological evidences of subsidence in the Nile Delta: Analysis of high resolution topographic DEM and multi-temporal satellite images

NASA Astrophysics Data System (ADS)

El Bastawesy, M.; Cherif, O. H.; Sultan, M.

2017-12-01

This paper investigates the relevance of landforms to the subsidence of the Nile Delta using a high resolution topographic digital elevation model (DEM) and sets of multi-temporal Landsat satellite images. 195 topographic map sheets produced in 1946 at 1:25,000 scale were digitized, and the DEM was interpolated. The undertaken processing techniques have distinguished all the natural low-lying closed depressions from the artificial errors induced by the interpolation of the DEM. The local subsidence of these depressions from their surroundings reaches a maximum depth of 2.5 m. The regional subsidence of the Nile Delta has developed inverted topography, where the tracts occupied by the contemporary distributary channels are standing at higher elevations than the areas in between. This inversion could be related to the differences in the hydrological and sedimentological properties of underlying sediments, as the channels are underlain by water-saturated sands while the successions of clay and silt on flood plains are prone to compaction. Furthermore, the analysis of remote sensing and topographic data clearly show significant changes in the land cover and land use, particularly in the northern lagoons and adjacent sabkhas, which are dominated by numerous low subsiding depressions. The areas covered by water logging and ponds are increasing on the expense of agricultural areas, and aquaculture have been practiced instead. The precise estimation of subsidence rates and distribution should be worked out to evaluate probable changes in land cover and land use.

Hydrological and hydraulic models for determination of flood-prone and flood inundation areas

NASA Astrophysics Data System (ADS)

Aksoy, Hafzullah; Sadan Ozgur Kirca, Veysel; Burgan, Halil Ibrahim; Kellecioglu, Dorukhan

2016-05-01

Geographic Information Systems (GIS) are widely used in most studies on water resources. Especially, when the topography and geomorphology of study area are considered, GIS can ease the work load. Detailed data should be used in this kind of studies. Because of, either the complication of the models or the requirement of highly detailed data, model outputs can be obtained fast only with a good optimization. The aim in this study, firstly, is to determine flood-prone areas in a watershed by using a hydrological model considering two wetness indexes; the topographical wetness index, and the SAGA (System for Automated Geoscientific Analyses) wetness index. The wetness indexes were obtained in the Quantum GIS (QGIS) software by using the Digital Elevation Model of the study area. Flood-prone areas are determined by considering the wetness index maps of the watershed. As the second stage of this study, a hydraulic model, HEC-RAS, was executed to determine flood inundation areas under different return period-flood events. River network cross-sections required for this study were derived from highly detailed digital elevation models by QGIS. Also river hydraulic parameters were used in the hydraulic model. Modelling technology used in this study is made of freely available open source softwares. Based on case studies performed on watersheds in Turkey, it is concluded that results of such studies can be used for taking precaution measures against life and monetary losses due to floods in urban areas particularly.

Amazonas project: Application of remote sensing techniques for the integrated survey of natural resources in Amazonas. [Brazil

NASA Technical Reports Server (NTRS)

Dejesusparada, N. (Principal Investigator)

1981-01-01

The use of LANDSAT multispectral scanner and return beam vidicon imagery for surveying the natural resources of the Brazilian Amazonas is described. Purposes of the Amazonas development project are summarized. The application of LANDSAT imagery to identification of vegetation coverage and soil use, identification of soil types, geomorphology, and geology and highway planning is discussed. An evaluation of the worth of LANDSAT imagery in mapping the region is presented. Maps generated by the project are included.

Preliminary integrated geologic map databases for the United States : Central states : Montana, Wyoming, Colorado, New Mexico, Kansas, Oklahoma, Texas, Missouri, Arkansas, and Louisiana

USGS Publications Warehouse

Stoeser, Douglas B.; Green, Gregory N.; Morath, Laurie C.; Heran, William D.; Wilson, Anna B.; Moore, David W.; Van Gosen, Bradley S.

2005-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for regional and national digital geologic maps attributed with age and lithology information. Such maps can be conveniently used to generate derivative maps for purposes including mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This Open-File Report is a preliminary version of part of a series of integrated state geologic map databases that cover the entire United States. The only national-scale digital geologic maps that portray most or all of the United States for the conterminous U.S. are the digital version of the King and Beikman (1974a, b) map at a scale of 1:2,500,000, as digitized by Schruben and others (1994) and the digital version of the Geologic Map of North America (Reed and others, 2005a, b) compiled at a scale of 1:5,000,000 which is currently being prepared by the U.S. Geological Survey. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. In a few cases, new digital compilations were prepared (e.g. OH, SC, SD) or existing paper maps were digitized (e.g. KY, TX). For Alaska and Hawaii, new regional maps are being compiled and ultimately new state maps will be produced. The digital geologic maps are presented in standardized formats as ARC/INFO (.e00) export files and as ArcView shape (.shp) files. Accompanying these spatial databases are a set of five supplemental data tables that relate the map units to detailed lithologic and age information. The maps for the CONUS have been fitted to a common set of state boundaries based on the 1:100,000 topographic map series of the United States Geological Survey (USGS). When the individual state maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps. No attempt has been made to reconcile differences in mapped geology across state lines. This is the first version of this product and it will be subsequently updated to include four additional states (North Dakota, South Dakota, Nebraska, and Iowa)

A multi-technique approach for characterizing the geomorphological evolution of a Villerville-Cricqueboeuf coastal landslide (Normandy, France).

NASA Astrophysics Data System (ADS)

Lissak Borges, Candide; Maquaire, Olivier; Malet, Jean-Philippe; Gomez, Christopher; Lavigne, Franck

2010-05-01

The Villerville and Cricqueboeuf coastal landslides (Calvados, Normandy, North-West France) have occurred in marly, sandy and chalky formations. The slope instability probably started during the last Quaternary period and is still active over the recent historic period. Since 1982, the slope is affected by a permanent activity (following the Varnes classification) with an annual average displacement of 5-10 cm.y-1 depending on the season. Three major events occurred in 1988, 1995 and 2001 and are controlled by the hydro-climatic conditions. These events induced pluri-decimetres to pluri-meters displacements (e.g. 5m horizontal displacements have been observed in 2001 at Cricqueboeuf) and generated economical and physical damage to buildings and roads. The landslide morphology is characterized by multi-metres scarps, reverse slopes caused by the tilting of landslide blocks and evolving cracks. The objective of this paper is to present the methodology used to characterize the recent historical (since 1808) geomorphological evolution of the landslides, and to discuss the spatio-temporal pattern of observed displacements. A multi-technique research approach has been applied and consisted in historical research, geomorphological mapping, geodetic monitoring and engineering geotechnical investigation. Information gained from different documents and techniques has been combined to propose a conceptual model of landslide evolution: - a retrospective study on landslide events inventoried in the historic period (archive investigation, newspapers); - a multi-temporal (1955-2006) analysis of aerial photographs (image processing, traditional stereoscopic techniques and image orthorectification), ancient maps and cadastres; - the creation of a detailed geomorphological map in 2009; - an analysis of recent displacements monitored since 1985 with traditional geodetic techniques (tacheometry, dGPS, micro-levelling) - geophysical investigation by ground-penetrating radar along the main road in order to assess the subsidence of the road according to the thickness of the filling material. Integration of the knowledge allows to characterize the landscape changes over the historical time. Displacement values obtained over nearly 200 years reflect annual slow movement and crisis acceleration. Values are dispersed in space and time. An average of displacements of 12.30 m year-1 (σ = 8.50) between 1829 and 2006 is observed for the Villerville landslide. This average allows calculating an annual displacement of 0.07 m which can be compared to data recorded since 1985 and by annual DGPS measurement data between 2008 and 2009.

To assess the value of satellite imagery in resource evaluation on a national scale. [South Africa

NASA Technical Reports Server (NTRS)

Malan, O. G. (Principal Investigator)

1973-01-01

The author has identified the following significant results. It has been shown that ERTS imagery, particularly in the form of 1:500,000 scale false color photolithographic prints, can contribute very significantly towards facilitating and accelerating (dramatically, in the case of vegetation) resource surveys and geologic mapping. Fire mapping on a national scale becomes a feasibility, numerous new geologic features, particularly lineaments, have been discovered, land use can be mapped efficiently on a regional scale and degraded areas identified. The first detailed tectonic and geomorphological maps of the Republic of South Africa will be published in the near future mainly owing to the availability of ERTS-1 imagery.

US GeoData: Digital cartographic and geographic data

USGS Publications Warehouse

,

1985-01-01

The increasing use of computers for storing and analyzing earth science information has sparked a growth in the demand for various types of cartographic data in digital form. The production of map data in computerized form is called digital cartography, and it involves the collection, storage, processing, analysis, and display of map data with the aid of computers. The U.S. Geological Survey, the Nation's largest earth science research agency, has expanded its national mapping program to incorporate operations associated with digital cartography, including the collection of planimetric, elevation, and geographic names information in digital form. This digital information is available for use in meeting the multipurpose needs and applications of the map user community.

Radiometric Survey in Western Afghanistan: A Website for Distribution of Data

USGS Publications Warehouse

Sweeney, Ronald E.; Kucks, Robert P.; Hill, Patricia L.; Finn, Carol A.

2007-01-01

Radiometric (uranium content, thorium content, potassium content, and gamma-ray intensity) and related data were digitized from radiometric and survey route location maps of western Afghanistan published in 1976. The uranium content data were digitized along contour lines from 33 maps in a series entitled 'Map of Uranium (Radium) Contents of Afghanistan (Western Area),' compiled by V. N. Kirsanov and R. S. Dershimanov. The thorium content data were digitized along contour lines from 33 maps in a series entitled 'Map of Thorium Contents of Afghanistan (Western Area),' compiled by V. N. Kirsanov and R. S. Dershimanov. The potassium content data were digitized along contour lines from 33 maps in a series entitled 'Map of Potassium Contents of Afghanistan (Western Area),' compiled by V. N. Kirsanov and R. S. Dershimanov. The gamma-ray intensity data were digitized along contour lines from 33 maps in a series entitled 'Map of Gamma-Field of Afghanistan (Western Area),' compiled by V. N. Kirsanov and R. S. Dershimanov. The survey route location data were digitized along flight-lines located on 33 maps in a series entitled 'Survey Routes Location and Contours of Flight Equal Altitudes. Western Area of Afghanistan,' compiled by Z. A. Alpatova, V. G. Kurnosov, and F. A. Grebneva.

Geologic Map of the Tucson and Nogales Quadrangles, Arizona (Scale 1:250,000): A Digital Database

USGS Publications Warehouse

Peterson, J.A.; Berquist, J.R.; Reynolds, S.J.; Page-Nedell, S. S.; Digital database by Oland, Gustav P.; Hirschberg, Douglas M.

2001-01-01

The geologic map of the Tucson-Nogales 1:250,000 scale quadrangle (Peterson and others, 1990) was digitized by U.S. Geological Survey staff and University of Arizona contractors at the Southwest Field Office, Tucson, Arizona, in 2000 for input into a geographic information system (GIS). The database was created for use as a basemap in a decision support system designed by the National Industrial Minerals and Surface Processes project. The resulting digital geologic map database can be queried in many ways to produce a variety of geologic maps. Digital base map data files (topography, roads, towns, rivers and lakes, etc.) are not included; they may be obtained from a variety of commercial and government sources. Additionally, point features, such as strike and dip, were not captured from the original paper map and are not included in the database. This database is not meant to be used or displayed at any scale larger than 1:250,000 (for example, 1:100,000 or 1:24,000). The digital geologic map graphics and plot files that are provided in the digital package are representations of the digital database. They are not designed to be cartographic products.

3D mapping of breast surface using digital fringe projection

NASA Astrophysics Data System (ADS)

Vairavan, Rajendaran; Retnasamy, Vithyacharan; Mohamad Shahimin, Mukhzeer; Sauli, Zaliman; Leng, Lai Siang; Wan Norhaimi, Wan Mokhzani; Marimuthu, Rajeswaran; Abdullah, Othman; Kirtsaeng, Supap

2017-02-01

Optical sensing technique has inherited non-contact nature for generating 3D surface mapping where its application ranges from MEMS component characterization, corrosion analysis, and vibration analysis. In particular, the digital fringe projection is utilized for 3D mapping of objects through the illumination of structured light for medical application extending from oral dental measurements, lower back deformation analysis, monitoring of scoliosis and 3D face reconstruction for biometric identification. However, the usage of digital fringe projection for 3D mapping of human breast is very minimal. Thus, this paper addresses the application of digital fringe projection for 3D mapping of breast surface based on total non-contact nature. In this work, phase shift method is utilized to perform the 3D mapping. The phase shifted fringe pattern are displayed through a digital projector onto the breast surface, and the distorted fringe patterns are captured by a CCD camera. A phase map is produced, and phase unwrapping was executed to obtain the 3D surface mapping of the breast. The surface height profile from 3D fringe projection was compared with the surface height measured by a direct method using electronic digital vernier caliper. Preliminary results showed the feasibility of digital fringe projection in providing a 3D mapping of breast and its application could be further extended for breast carcinoma detection.

Specification for the U.S. Geological Survey Historical Topographic Map Collection

USGS Publications Warehouse

Allord, Gregory J.; Walter, Jennifer L.; Fishburn, Kristin A.; Shea, Gale A.

2014-01-01

This document provides the detailed requirements for producing, archiving, and disseminating a comprehensive digital collection of topographic maps for the U.S. Geological Survey (USGS) Historical Topographic Map Collection (HTMC). The HTMC is a digital archive of about 190,000 printed topographic maps published by the USGS from the inception of the topographic mapping program in 1884 until the last paper topographic map using lithographic printing technology was published in 2006. The HTMC provides a comprehensive digital repository of all scales and all editions of USGS printed topographic maps that is easily discovered, browsed, and downloaded by the public at no cost. The HTMC provides ready access to maps that are no longer available for distribution in print. A digital file representing the original paper historical topographic map is produced for each historical map in the HTMC in georeferenced PDF (GeoPDF) format (a portable document format [PDF] with a geospatial extension).

Producing Alaska interim land cover maps from Landsat digital and ancillary data

USGS Publications Warehouse

Fitzpatrick-Lins, Katherine; Doughty, Eileen Flanagan; Shasby, Mark; Loveland, Thomas R.; Benjamin, Susan

1987-01-01

In 1985, the U.S. Geological Survey initiated a research program to produce 1:250,000-scale land cover maps of Alaska using digital Landsat multispectral scanner data and ancillary data and to evaluate the potential of establishing a statewide land cover mapping program using this approach. The geometrically corrected and resampled Landsat pixel data are registered to a Universal Transverse Mercator (UTM) projection, along with arc-second digital elevation model data used as an aid in the final computer classification. Areas summaries of the land cover classes are extracted by merging the Landsat digital classification files with the U.S. Bureau of Land Management's Public Land Survey digital file. Registration of the digital land cover data is verified and control points are identified so that a laser plotter can products screened film separate for printing the classification data at map scale directly from the digital file. The final land cover classification is retained both as a color map at 1:250,000 scale registered to the U.S. Geological Survey base map, with area summaries by township and range on the reverse, and as a digital file where it may be used as a category in a geographic information system.

Spatial digital database for the geologic map of the east part of the Pullman 1° x 2° quadrangle, Idaho

USGS Publications Warehouse

Rember, William C.; Bennett, Earl H.

2001-01-01

he paper geologic map of the east part of the Pullman 1·x 2· degree quadrangle, Idaho (Rember and Bennett, 1979) was scanned and initially attributed by Optronics Specialty Co., Inc. (Northridge, CA) and remitted to the U.S. Geological Survey for further attribution and publication of the geospatial digital files. The resulting digital geologic map GIS can be queried in many ways to produce a variety of geologic maps. This digital geospatial database is one of many being created by the U.S. Geological Survey as an ongoing effort to provide geologic information in a geographic information system (GIS) for use in spatial analysis. Digital base map data files (topography, roads, towns, rivers and lakes, and others.) are not included: they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:250,000 (for example, 1:100,000 or 1:24,000). The digital geologic map graphics and plot files (pull250k.gra/.hp /.eps) that are provided in the digital package are representations of the digital database.

Digital floodplain mapping and an analysis of errors involved

USGS Publications Warehouse

Hamblen, C.S.; Soong, D.T.; Cai, X.

2007-01-01

Mapping floodplain boundaries using geographical information system (GIS) and digital elevation models (DEMs) was completed in a recent study. However convenient this method may appear at first, the resulting maps potentially can have unaccounted errors. Mapping the floodplain using GIS is faster than mapping manually, and digital mapping is expected to be more common in the future. When mapping is done manually, the experience and judgment of the engineer or geographer completing the mapping and the contour resolution of the surface topography are critical in determining the flood-plain and floodway boundaries between cross sections. When mapping is done digitally, discrepancies can result from the use of the computing algorithm and digital topographic datasets. Understanding the possible sources of error and how the error accumulates through these processes is necessary for the validation of automated digital mapping. This study will evaluate the procedure of floodplain mapping using GIS and a 3 m by 3 m resolution DEM with a focus on the accumulated errors involved in the process. Within the GIS environment of this mapping method, the procedural steps of most interest, initially, include: (1) the accurate spatial representation of the stream centerline and cross sections, (2) properly using a triangulated irregular network (TIN) model for the flood elevations of the studied cross sections, the interpolated elevations between them and the extrapolated flood elevations beyond the cross sections, and (3) the comparison of the flood elevation TIN with the ground elevation DEM, from which the appropriate inundation boundaries are delineated. The study area involved is of relatively low topographic relief; thereby, making it representative of common suburban development and a prime setting for the need of accurately mapped floodplains. This paper emphasizes the impacts of integrating supplemental digital terrain data between cross sections on floodplain delineation. ?? 2007 ASCE.

Mapping and quantifying geodiversity in land-water transition zones using MBES and topobathymetric LiDAR

NASA Astrophysics Data System (ADS)

Brandbyge Ernstsen, Verner; Skovgaard Andersen, Mikkel; Gergely, Aron; Schulze Tenberge, Yvonne; Al-Hamdani, Zyad; Steinbacher, Frank; Rolighed Larsen, Laurids; Winter, Christian; Bartholomä, Alexander

2016-04-01

Land-water transition zones, like e.g. coastal and fluvial environments, are valuable ecosystems which are often characterised by high biodiversity and geodiversity. However, often these land-water transition zones are difficult or even impossible to map and investigate in high spatial resolution due to the challenging environmental conditions. Combining vessel borne shallow water multibeam echosounder (MBES) surveys ,to cover the subtidal coastal areas and the river channel areas, with airborne topobathymetric light detection and ranging (LiDAR) surveys, to cover the intertidal and supratidal coastal areas and the river floodplain areas, potentially enables full-coverage and high-resolution mapping in these challenging environments. We have carried out MBES and topobathymetric LiDAR surveys in the Knudedyb tidal inlet system, a coastal environment in the Danish Wadden Sea which is part of the Wadden Sea National Park and UNESCO World Heritage, and in the Ribe Vesterå, a fluvial environment in the Ribe Å river catchment discharging into the Knudedyb tidal basin. Detailed digital elevation models (DEMs) with a grid cell size of 0.5 m x 0.5 m were generated from the MBES and the LiDAR point clouds, which both have point densities in the order of 20 points/m2. Morphometric analyses of the DEMs enabled the identification and mapping of the different landforms within the coastal and fluvial environments. Hereby, we demonstrate that vessel borne MBES and airborne topobathymetric LiDAR, here in combination, are promising tools for seamless mapping across land-water transition zones as well as for the quantification of a range of landforms at landscape scale in different land-water transition zone environments. Hence, we demonstrate the potential for mapping and quantifying geomorphological diversity, which is one of the main components of geodiversity and a prerequisite for assessing geoheritage. Acknowledgements This work was funded by the Danish Council for Independent Research | Natural Sciences through the project "Process-based understanding and prediction of morphodynamics in a natural coastal system in response to climate change" (Steno Grant no. 10-081102) and by the Geocenter Denmark through the project "Closing the gap! - Coherent land-water environmental mapping (LAWA)" (Grant no. 4-2015).

Digital geologic map of the Spokane 1:100,000 quadrangle, Washington and Idaho: a digital database for the 1990 N.L. Joseph map

USGS Publications Warehouse

Johnson, Bruce R.; Derkey, Pamela D.

1998-01-01

Geologic data from the geologic map of the Spokane 1:100,000-scale quadrangle compiled by Joseph (1990) were entered into a geographic information system (GIS) as part of a larger effort to create regional digital geology for the Pacific Northwest. The map area is located in eastern Washington and extends across the state border into western Idaho (Fig. 1). This open-file report describes the methods used to convert the geologic map data into a digital format, documents the file structures, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet.

Tectonic geomorphology of the New Madrid seismic zone based on imaging of digital topographic data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mayer, L.

1993-03-01

Topographic analysis using digital elevation data of the New Madrid region focuses on topographic features that occur at several spatial scales and can be used to delineate distinct anomalies. In this region, topographic anomalies occur as domal or elongate uplifts and bowl-shaped depressions approximately 1--10 km in size, topographic lineaments, and differences in topographic blocking across 50 km long boundaries. In order to fully explain these topographic anomalies, tectonic processes may be required. Imaging is based on digital topographic data from USGS 30 arc-second, 3 arc-second, and 30 m resolutions. Imaging of these data uses standard imaging processing techniques tomore » examine topography within the contexts of geomorphological hypothesis testing. A good example is the use of thresholding to highlight areas of unusually high elevation given the hypothesis of fluvial landscape architecture. Thresholding delineates topographic features such as the Tiptonville dome which is strongly believed to be tectonic in origin. To determine the pattern of topographic blocking, defined as a pattern that topography assumes when constrained by active forces other than erosion alone, low frequency passing spatial convolutions are used as filters and the resulting data are sliced into blocks according to pseudoelevations that produce a stable block pattern. The resultant blocks are analyzed according to its structural pattern of block size and block orientation. This analysis suggests that a topographic boundary cuts across the Mississippi embayment from near the Newport pluton on the west, to the area south of Memphis on east.« less

Comparison of Terrestrial Laser Scanning (TLS) and Structure from Motion (SfM) photogrammetry from unmanned aerial systems (UAS) for geomorphic change detection in beach-dune systems.

NASA Astrophysics Data System (ADS)

Heathfield, D.; Walker, I. J.; Grilliot, M. J.

2016-12-01

The recent emergence of terrestrial laser scanning (TLS) and unmanned aerial systems (UAS) as mapping platforms in geomorphology research has allowed for expedited acquisition of high spatial and temporal resolution, three-dimensional topographic datasets. TLS provides dense 3D `point cloud' datasets that require careful acquisition strategies and appreciable post-processing to produce accurate digital elevation models (DEMs). UAS provide overlapping nadir and oblique imagery that can be analysed using Structure from Motion (SfM) photogrammetry software to provide accurate, high-resolution orthophoto mosaics and accurate digital surface models (DSMs). Both methods yield centimeter to decimeter scale accuracy, depending on various hardware and field acquisition considerations (e.g., camera resolution, flight height, on-site GNSS control, etc.). Combined, the UAS-SfM workflow provides a comparable and more affordable solution to the more expensive TLS or aerial LiDAR methods. This paper compares and contrasts SfM and TLS survey methodologies and related workflow costs and benefits as used to quantify and examine seasonal beach-dune erosion and recovery processes at a site (Calvert Island) on British Columbia's central coast in western Canada. Seasonal SfM- and TLS-derived DEMs were used to quantify spatial patterns of surface elevation change, geomorphic responses, and related significant sediment volume changes. Cluster maps of positive (depositional) and negative (erosional) change are analysed to detect and interpret the geomorphic and sediment budget responses following an erosive water level event during winter 2016 season (Oct. 2015 - Apr. 2016). Vantage cameras also provided qualitative data on the frequency and magnitude of environmental drivers (e.g., tide, wave, wind forcing) of erosion and deposition events during the observation period. In addition, we evaluate the costs, time expenditures, and accuracy considerations for both SfM and TLS methodologies.

Geologic and structure map of the Choteau 1 degree by 2 degrees Quadrangle, western Montana

USGS Publications Warehouse

Mudge, Melville R.; Earhart, Robert L.; Whipple, James W.; Harrison, Jack E.

1982-01-01

The geologic and structure map of Choteau 1 x 2 degree quadrangle (Mudge and others, 1982) was originally converted to a digital format by Jeff Silkwood (U.S. Forest Service and completed by the U.S. Geological Survey staff and contractor at the Spokane Field Office (WA) in 2000 for input into a geographic information system (GIS). The resulting digital geologic map (GIS) database can be queried in many ways to produce a variey of geologic maps. Digital base map data files (topography, roads, towns, rivers and lakes, etc.) are not included: they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:250,000 (e.g. 1:100,000 or 1:24,000. The digital geologic map graphics and plot files (chot250k.gra/.hp/.eps and chot-map.pdf) that are provided in the digital package are representations of the digital database. They are not designed to be cartographic products.

Reports of Planetary Geology and Geophysics Program, 1984

NASA Technical Reports Server (NTRS)

Holt, H. E. (Compiler); Watters, T. R. (Compiler)

1985-01-01

Topics include outer planets and satellites; asteroids and comets; Venus; lunar origin and solar dynamics; cratering process; planetary interiors, petrology, and geochemistry; volcanic processes; aeolian processes and landforms; fluvial processes; geomorphology; periglacial and permafrost processes; remote sensing and regolith studies; structure, tectonics, and stratigraphy; geological mapping, cartography, and geodesy; and radar applications.

Hyperspectral remote sensing and GIS techniques application for the evaluation and monitoring of interactions between natural risks and industrial hazards

NASA Astrophysics Data System (ADS)

Marino, Alessandra; Ludovisi, Giancarlo; Moccaldi, Antonio; Damiani, Fiorenzo

2001-02-01

The aim of this paper is to outline the potential of imaging spectroscopy and GIS techniques as tool for the management of data rich environments, as complex fluvial areas, exposed to geological, geomorphological, and hydrogeological risks. The area of study, the Pescara River Basin is characterized by the presence of important industrial sites and by the occurrence of floods, landslides and seismic events. Data were collected, during a specific flight, using an hyperspectral MIVIS sensor. Images have been processed in order to obtain updated and accurate land-cover and land-use maps that have been inserted in a specific GIS database and integrated with further information like lithology, geological structure, geomorphology, hydrogeological features, productive plants location and characters. The processing of data layers was performed, using a dedicated software, through typical GIS operators like indexing, recording, matrix analysis, proximity analysis. The interactions between natural risks, industrial installations, agricultural areas, water resources and urban settlements have been analyzed. This allowed the creation and processing of thematic layers like vulnerability, risk and impact maps.

Preliminary Study on Earthquake Surface Rupture Extraction from Uav Images

NASA Astrophysics Data System (ADS)

Yuan, X.; Wang, X.; Ding, X.; Wu, X.; Dou, A.; Wang, S.

2018-04-01

Because of the advantages of low-cost, lightweight and photography under the cloud, UAVs have been widely used in the field of seismic geomorphology research in recent years. Earthquake surface rupture is a typical seismic tectonic geomorphology that reflects the dynamic and kinematic characteristics of crustal movement. The quick identification of earthquake surface rupture is of great significance for understanding the mechanism of earthquake occurrence, disasters distribution and scale. Using integrated differential UAV platform, series images were acquired with accuracy POS around the former urban area (Qushan town) of Beichuan County as the area stricken seriously by the 2008 Wenchuan Ms8.0 earthquake. Based on the multi-view 3D reconstruction technique, the high resolution DSM and DOM are obtained from differential UAV images. Through the shade-relief map and aspect map derived from DSM, the earthquake surface rupture is extracted and analyzed. The results show that the surface rupture can still be identified by using the UAV images although the time of earthquake elapse is longer, whose middle segment is characterized by vertical movement caused by compression deformation from fault planes.

Geomorphologic mapping of the lunar crater Tycho and its impact melt deposits

NASA Astrophysics Data System (ADS)

Krüger, T.; van der Bogert, C. H.; Hiesinger, H.

2016-07-01

Using SELENE/Kaguya Terrain Camera and Lunar Reconnaissance Orbiter Camera (LROC) data, we produced a new, high-resolution (10 m/pixel), geomorphological and impact melt distribution map for the lunar crater Tycho. The distal ejecta blanket and crater rays were investigated using LROC wide-angle camera (WAC) data (100 m/pixel), while the fine-scale morphologies of individual units were documented using high resolution (∼0.5 m/pixel) LROC narrow-angle camera (NAC) frames. In particular, Tycho shows a large coherent melt sheet on the crater floor, melt pools and flows along the terraced walls, and melt pools on the continuous ejecta blanket. The crater floor of Tycho exhibits three distinct units, distinguishable by their elevation and hummocky surface morphology. The distribution of impact melt pools and ejecta, as well as topographic asymmetries, support the formation of Tycho as an oblique impact from the W-SW. The asymmetric ejecta blanket, significantly reduced melt emplacement uprange, and the depressed uprange crater rim at Tycho suggest an impact angle of ∼25-45°.

Comparative Performance Analysis of a Hyper-Temporal Ndvi Analysis Approach and a Landscape-Ecological Mapping Approach

NASA Astrophysics Data System (ADS)

Ali, A.; de Bie, C. A. J. M.; Scarrott, R. G.; Ha, N. T. T.; Skidmore, A. K.

2012-07-01

Both agricultural area expansion and intensification are necessary to cope with the growing demand for food, and the growing threat of food insecurity which is rapidly engulfing poor and under-privileged sections of the global population. Therefore, it is of paramount importance to have the ability to accurately estimate crop area and spatial distribution. Remote sensing has become a valuable tool for estimating and mapping cropland areas, useful in food security monitoring. This work contributes to addressing this broad issue, focusing on the comparative performance analysis of two mapping approaches (i) a hyper-temporal Normalized Difference Vegetation Index (NDVI) analysis approach and (ii) a Landscape-ecological approach. The hyper-temporal NDVI analysis approach utilized SPOT 10-day NDVI imagery from April 1998-December 2008, whilst the Landscape-ecological approach used multitemporal Landsat-7 ETM+ imagery acquired intermittently between 1992 and 2002. Pixels in the time-series NDVI dataset were clustered using an ISODATA clustering algorithm adapted to determine the optimal number of pixel clusters to successfully generalize hyper-temporal datasets. Clusters were then characterized with crop cycle information, and flooding information to produce an NDVI unit map of rice classes with flood regime and NDVI profile information. A Landscape-ecological map was generated using a combination of digitized homogenous map units in the Landsat-7 ETM+ imagery, a Land use map 2005 of the Mekong delta, and supplementary datasets on the regions terrain, geo-morphology and flooding depths. The output maps were validated using reported crop statistics, and regression analyses were used to ascertain the relationship between land use area estimated from maps, and those reported in district crop statistics. The regression analysis showed that the hyper-temporal NDVI analysis approach explained 74% and 76% of the variability in reported crop statistics in two rice crop and three rice crop land use systems respectively. In contrast, 64% and 63% of the variability was explained respectively by the Landscape-ecological map. Overall, the results indicate the hyper-temporal NDVI analysis approach is more accurate and more useful in exploring when, why and how agricultural land use manifests itself in space and time. Furthermore, the NDVI analysis approach was found to be easier to implement, was more cost effective, and involved less subjective user intervention than the landscape-ecological approach.

Airborne photogrammetry and geomorphological analysis of the 2001-2012 exogenous dome growth at Molodoy Shiveluch Volcano, Kamchatka

NASA Astrophysics Data System (ADS)

Shevchenko, A. V.; Dvigalo, V. N.; Svirid, I. Yu.

2015-10-01

In 2001, after a six-year pause in extrusive activity, lava dome growth resumed at Molodoy Shiveluch Volcano. The new period of dome growth (2001-present) has morphological features that were uncommon during the previous periods of the dome formation (1980-1981, 1993-1995): numerous lava lobes and crease structures. Thus, the current dome growth is mostly of an exogenous type with short periods of endogenous growth that occurred in 2003, 2005, and 2010. Geomorphological interpretation of stereo photo images has revealed elements of the dome that are hardly distinguishable in single photographs. We have made detailed descriptions of the dome morphology covering all the dates of the available images. By using photogrammetric processing of aerial photographs, we created Digital Terrain Models and topographic maps of the lava dome and defined its volumes for 2001 (0.19 km3), 2003 (0.47 km3), 2005 (0.48 km3), 2010 (0.54 km3), and 2012 (0.63 km3). We also defined other morphometric characteristics: absolute and relative heights, as well as the dimensions of the dome and its elements for the investigated period. Taking into account large partial failures of the dome in 2005 (>0.11 km3) and 2010 (0.28 km3), we suggest that the volume of the extruded material for the whole 1980-2012 period was no less than 1.02 km3. The average extrusion rate over the 2001-2012 period exceeded 225,000 m3/day. The transition from endogenous to exogenous dome growth was possibly caused by change in extruded material physical properties due to an increase of SiO2. On the basis of geomorphological analysis of the current lava dome features, we suggest the possible process of the exogenous dome formation at Molodoy Shiveluch. The crease structures detected at Molodoy Shiveluch were classified into three groups according to their shapes: radial, bilaterally symmetrical, and irregular. These crease structures are morphologically similar to those formed at Unzen Volcano during the 1990-1995 eruption. Some revealed morphological features of the crease structures show that the role of gravity is insignificant in their formation. We assume that the crease structures at Molodoy Shiveluch were formed by inner stresses due to thermal and solidification gradients.

Assessment of present day geomorphological dynamics to decipher landscape evolution around the Paleolithic sites of Melka Kunture, Ethiopia

NASA Astrophysics Data System (ADS)

Maerker, Michael; Schillaci, Calogero; Melis, Rita; Mussi, Margherita

2014-05-01

The area of Melka Kunture (central Ethiopia) is one of the most important clusters of Paleolithic sites in Eastern Africa. The archaeological record spans from c. 1.7 Ma onwards, with a number of stratified occurrences of Oldowan, Acheulean, Middle Stone Age and Late Stone Age industries, together with faunal remains and human fossils. However, the archaeological sites are endangered by flooding and soil erosion. The main excavation area lies close to the convergence of the Awash river with the Atabella river, one of the main tributaries of the upper Awash catchment. In the semi-arid Ethiopian highlands, gully networks develop especially in the vicinity of the active and inactive river meanders. Various erosion processes are linked to specific driving factors such as the rainfall regime, the land use/cover changes and vertic soils with a specific hydrological behaviour. It was documented in the field and by previous research that the origin of most of the man made erosion channels is due to animal pathways and car tracks. However, paleolandscape features increase the general erosion risk. Former wetland areas and deposition zones are particularly affected by soil erosion processes. Hence, the spatial distribution and characteristics of present day geomorphic processes also reveal information on the paleolandscape. In order to assess landscape evolution and present day geomorphologic dynamics, we mapped the geomorphology describing in detail the present-day slope processes at a 10.000 scale. We performed a detailed terrain analysis based on high resolution DEMs such as SRTM-X with 25m resolution and ALOS/PRISM with 10m resolution to characterize the main erosion processes and surface runoff dynamics. The latter ones are simulated using a Soil Conservation Service Curve Number method. Landuse was delineated for a larger area using ASTER 25m multispectral data. Finally, using calibrated topographic indices and a simple hydrological model we were able to detect and quantify the major present day soil erosion and surface runoff processes. Based on the analysis of the processes and the respective terrain features derived from the digital elevation models we also identified the major paelolandscape features. This will be the basis for assessing conservation risks related to modern land use and climate.

A Coastal Hazards Data Base for the U.S. Gulf Coast (1993) (NDP-04bB)

DOE Data Explorer

Gornitz, Vivien M. [National Aeronautics and Space Administration, Goddard Institute for Space Studies, New York, NY (USA); White, Tammy W. [CDIAC, Oak Ridge National Laboratory, Oak Ridge, TN (USA)

2008-01-01

This document describes the contents of a digital data base that may be used to identify coastlines along the U.S. Gulf Coast at risk to sea-level rise. The data base integrates point, line, and polygon data for the U.S. Gulf Coast into 0.25° latitude by 0.25° longitude grid cells and into 1:2,000,000 digitized line segments that can be used by raster or vector geographic information systems (GIS) as well as by non-GIS data base systems. Each coastal grid cell and line segment contains data on elevations, geology, geomorphology, sea-level trends, shoreline displacement (erosion/accretion), tidal ranges, and wave heights.

Evaluation of LiDAR Imagery as a Tool for Mapping the Northern San Andreas Fault in Heavily Forested Areas of Mendocino and Sonoma Counties, California

NASA Astrophysics Data System (ADS)

Prentice, C. S.; Koehler, R. D.; Baldwin, J. N.; Harding, D. J.

2004-12-01

We are mapping in detail active traces of the San Andreas Fault in Mendocino and Sonoma Counties in northern California, using recently acquired airborne LiDAR (also known as ALSM) data. The LiDAR data set provides a powerful new tool for mapping geomorphic features related to the San Andreas Fault because it can be used to produce high-resolution images of the ground surfaces beneath the forest canopy along the 70-km-long section of the fault zone encompassed by the data. Our effort represents the first use of LiDAR data to map active fault traces in a densely vegetated region along the San Andreas Fault. We are using shaded relief images generated from bare-earth DEMs to conduct detailed mapping of fault-related geomorphic features (e.g. scarps, offset streams, linear valleys, shutter ridges, and sag ponds) between Fort Ross and Point Arena. Initially, we map fault traces digitally, on-screen, based only on the geomorphology interpreted from LiDAR images. We then conduct field reconnaissance using the initial computer-based maps in order to verify and further refine our mapping. We found that field reconnaissance is of utmost importance in producing an accurate and detailed map of fault traces. Many lineaments identified as faults from the on-screen images were determined in the field to be old logging roads or other features unrelated to faulting. Also, in areas where the resolution of LiDAR data is poor, field reconnaissance, coupled with topographic maps and aerial photographs, permits a more accurate location of fault-related geomorphic features. LiDAR images are extremely valuable as a base for field mapping in this heavily forested area, and the use of LiDAR is far superior to traditional mapping techniques relying only on aerial photography and 7.5 minute USGS quadrangle topographic maps. Comparison with earlier mapping of the northern San Andreas fault (Brown and Wolfe, 1972) shows that in some areas the LiDAR data allow a correction of the fault trace location of up to several hundred meters. To date we have field checked approximately 24 km of the 70-km-long section of the fault for which LiDAR data is available. The remaining 46 km will be field checked in 2005. The result will be a much more accurate map of the active traces of the northern San Andreas Fault, which will be of great use for future fault studies.

Proceedings of a workshop on digital mapping techniques; methods for geologic map data capture, management, and publication - June 2 - 5, 1997, Lawrence, Kansas

USGS Publications Warehouse

Soller, David R.

1997-01-01

Introduction: From June 2-5, 1997, selected technical representatives of the USGS and State geological surveys participated in the 'AASG/USGS Digital Mapping Techniques' workshop in Lawrence, Kansas. The workshop was initiated by the AASG/USGS Data Capture Working Group, and was hosted by the Kansas Geological Survey (KGS). With a focus on methods for data capture and digital map production, the goal was to help move the state surveys and the USGS toward development of more cost-effective, flexible, and useful systems for digital mapping and GIS analysis.

Digital Mapping Techniques '09-Workshop Proceedings, Morgantown, West Virginia, May 10-13, 2009

USGS Publications Warehouse

Soller, David R.

2011-01-01

As in the previous years' meetings, the objective was to foster informal discussion and exchange of technical information, principally in order to develop more efficient methods for digital mapping, cartography, GIS analysis, and information management. At this meeting, oral and poster presentations and special discussion sessions emphasized (1) methods for creating and publishing map products (here, "publishing" includes Web-based release); (2) field data capture software and techniques, including the use of LiDAR; (3) digital cartographic techniques; (4) migration of digital maps into ArcGIS Geodatabase format; (5) analytical GIS techniques; and (6) continued development of the National Geologic Map Database.

A Limnological Examination of the Southwestern Amazon, Madre de Dios, Peru

NASA Astrophysics Data System (ADS)

Belcon, Alana Urnesha

This dissertation investigates the limnology of the southwestern Peruvian Amazon centered on the Madre de Dios department by examining first the geomorphology and then the ecology and biogeochemistry of the region's fluvial systems. Madre de Dios, Peru is world renowned for its prolific biodiversity and its location within the Andes biodiversity hotspot. It is also a site of study regarding the development of the Fitzcarrald Arch and that feature's geomorphological importance as the drainage center for the headwaters of the Madeira River---the Amazon's largest tributary and as well as its role as a physical divider of genetic evolution in the Amazon. Though each of these has been studied by a variety of prominent researchers, the ability to investigate all the aspects of this unique region is hampered by the lack of a regional geomorphological map. This study aims to fill that gap by using remote sensing techniques on digital elevation models, satellite imagery and soil, geology and geoecological maps already in publication to create a geomorphological map. The resulting map contains ten distinct landform types that exemplify the dominance of fluvial processes in shaping this landscape. The river terraces of the Madre de Dios River are delineated in their entirety as well as the various dissected relief units and previously undefined units. The demarcation of the boundaries of these geomorphic units will provide invaluable assistance to the selection of field sites by future researchers as well as insights into the origin of the high biodiversity indices of this region and aid in planning for biodiversity conservation. Secondly this study examines 25 tropical floodplain lakes along 300 km of the Manu River within the Manu National Park in the Madre de Dios department. Alternative stable state and regime shifts in shallow lakes typically have been examined in lakes in temperate and boreal regions and within anthropogenically disturbed basins but have rarely been studied in tropical or in undisturbed regions. In contrast this study focuses on a tropical region of virtually no human disturbance and evaluates the effects of hydrological variability on ecosystem structure and dynamics. Using satellite imagery a 23 yr timeline of ecological regime shifts in Amazon oxbow lakes or "cochas" is reconstructed. The study shows that almost 25% of the river's floodplain lakes experience periodic abrupt vegetative changes with an average 3.4% existing in an alternative stable state in any given year. State changes typically occur from a stable phytoplankton-dominated state to a short lived, <3 yr, floating macrophytic state and often occur independent of regional flooding. We theorize that multiple dynamics, both internal and external, drive vegetative regime shifts in the Manu but insufficient data yet exists in this remote region to identify the key processes. To complete the investigation of tropical limnology the third study compares and contrasts the nutrient-productivity ration of floodplain and non-floodplain lakes globally and regionally. For over 70 years a strong positive relationship between sestonic chlorophyll-a (Chl-a) and total phosphorus (TP) has been established with phosphorus generally viewed as the most limiting factor to productivity. Most of these studies, however, have focused on northern, temperate regions where the lakes are typically postglacial, isolated and fed by small streams. Relatively little work has been done on floodplain lakes which are semi or permanently connected to the river. This study examines the relationship between nutrients and productivity in floodplain lakes globally through an extensive literature synthesis. Values for total phosphorus, total nitrogen and chlorophyll-a were collected for 523 floodplain lakes, represented by 288 data points while 551 data points were collected for 5444 non-floodplain lakes. Analysis revealed that globally, floodplain lakes do not show any significant difference in the total phosphorus/chlorophyll-a relationship from that found in non-floodplain lakes but significant differences are seen between tropical and temperate lakes. We propose that the term 'floodplain' lake should serve as purely a geographical descriptor and that it is lacking as an ecological indicator. Instead factors such as precipitation seasonality, hydrological connectivity and regional flooding regimes are better indicators of high or low productivity in floodplain lakes.

Digital Mapping Techniques '11–12 workshop proceedings

USGS Publications Warehouse

Soller, David R.

2014-01-01

At these meetings, oral and poster presentations and special discussion sessions emphasized: (1) methods for creating and publishing map products (here, "publishing" includes Web-based release); (2) field data capture software and techniques, including the use of LiDAR; (3) digital cartographic techniques; (4) migration of digital maps into ArcGIS Geodatabase formats; (5) analytical GIS techniques; and (6) continued development of the National Geologic Map Database.

Procedure for extraction of disparate data from maps into computerized data bases

NASA Technical Reports Server (NTRS)

Junkin, B. G.

1979-01-01

A procedure is presented for extracting disparate sources of data from geographic maps and for the conversion of these data into a suitable format for processing on a computer-oriented information system. Several graphic digitizing considerations are included and related to the NASA Earth Resources Laboratory's Digitizer System. Current operating procedures for the Digitizer System are given in a simplified and logical manner. The report serves as a guide to those organizations interested in converting map-based data by using a comparable map digitizing system.

Structural Mapping and Geomorphology of Ireland's Southwest Continental Shelf Using High Resolution Sonar

NASA Astrophysics Data System (ADS)

Bowden, S.; Wireman, R.

2016-02-01

Bathymetric surveys were conducted on the continental shelf off the southwest coast of County Cork, Ireland by the Marine Institute of Ireland, the Geological Survey of Ireland, and the INFOMAR project. Data were collected from July 2006 through September 2014 using a Kongsberg EM2040 multibeam echosounder aboard the R/Vs Celtic Voyager and Keary, and a Kongsberg EM1002 on the R/V Celtic Explorer. Sonar data were post-processed with CARIS HIPS and SIPS 9.0 to create 2D and 3D bathymetric and backscatter intensity surfaces with a resolution of 1 m. The offshore study site is part of the 286 Ma western Variscian orogenic front and has several massive outcrops, exhibiting 5 to 20 m of near-vertical relief. These outcrops were structurally mapped and relatively aged, and exhibit significant folding, rotation, tilting, and joint systems. Google Earth, ArcGIS, and previous terrestrial studies were used to further analyze how geomorphology is controlled by seafloor composition and structural features. Rock type and age were interpreted by comparing fracture analysis of the joints and fold trends to similar onshore outcrops documented previously, to determine an age of 416-299 Ma for the shelf's outcropping strata and associated structural features. The oldest features observed are regional anticlines and synclines containing Upper Devonian Old Red Sandstone and Lower Carboniferous shales. Within the shale layers are NE-SW plunging parasitic chevron folds. Jointing is observed in both sandstone and shale layers and is superimposed on chevron folding, with cross joints appearing to influence shallow current patterns. Rotation of the regional folds is the youngest structural feature, as both the parasitic folds and joint systems are warped. Our study shows that high resolution sonar is an effective tool for offshore structural mapping and is an important resource for understanding the geomorphology and geologic history of submerged outcrops on continental shelf systems.

Geological features indicative of processes related to the hematite formation in Meridiani Planum and Aram Chaos, Mars: a comparison with diagenetic hematite deposits in southern Utah, USA

NASA Astrophysics Data System (ADS)

Ormö, Jens; Komatsu, Goro; Chan, Marjorie A.; Beitler, Brenda; Parry, William T.

2004-10-01

In order to understand the formation of the few but large, hematite deposits on Mars, comparisons are often made with terrestrial hematite occurrences. In southern Utah, hematite concretions have formed within continental sandstones and are exposed as extensive weathered-out beds. The hematite deposits are linked to geological and geomorphological features such as knobs, buttes, bleached beds, fractures and rings. These terrestrial features are visible in aerial and satellite images, which enables a comparison with similar features occurring extensively in the martian hematite-rich areas. The combination of processes involved in the movement and precipitation of iron in southern Utah can provide new insights in the context of the hematite formation on Mars. Here we present a mapping of the analogue geological and geomorphological features in parts of Meridiani Planum and Aram Chaos. Based on mapping comparisons with the Utah occurrences, we present models for the formation of the martian analogues, as well as a model for iron transport and precipitation on Mars. Following the Utah model, high albedo layers and rings in the mapped area on Mars are due to removal or lack of iron, and precipitation of secondary diagenetic minerals as fluids moved up along fractures and permeable materials. Hematite was precipitated intraformationally where the fluid transporting the reduced iron met oxidizing conditions. Our study shows that certain geological/geomorphological features can be linked to the hematite formation on Mars and that pH differences could suffice for the transport of the iron from an orthopyroxene volcanoclastic source rock. The presence of organic compounds can enhance the iron mobilization and precipitation processes. Continued studies will focus on possible influence of biological activity and/or methane in the formation of the hematite concretions in Utah and on Mars.

An Interactive Map Viewer for the Urban Geology of Ottawa (Canada): an Example of Web Publishing

NASA Astrophysics Data System (ADS)

Giroux, D.; Bélanger, R.

2003-04-01

Developed by the Terrain Sciences Division (TSD) of the Geological Survey of Canada (GSC), an interactive map viewer, called GEOSERV (www.geoserv.org), is now available on the Internet. The purpose of this viewer is to provide engineers, planners, decision makers, and the general public with the geoscience information required for sound regional planning in densely populated areas, such as Canada's national capital, Ottawa (Ontario). Urban geology studies rely on diverse branches of earth sciences such as hydrology, engineering geology, geochemistry, stratigraphy, and geomorphology in order to build a three-dimensional model of the character of the land and to explain the geological processes involved in the dynamic equilibrium of the local environment. Over the past few years, TSD has compiled geoscientific information derived from various sources such as borehole logs, geological maps, hydrological reports and digital elevation models, compiled it in digital format and stored it in georeferenced databases in the form of point, linear, and polygonal data. This information constitutes the geoscience knowledge base which is then processed by Geographic Information Systems (GIS) to integrate the various sources of information and produce derived graphics, maps and models describing the geological infrastructure and response of the geological environment to human activities. Urban Geology of Canada's National Capital Area is a pilot project aiming at developing approaches, methodologies and standards that can be applied to other major urban centres of the country, while providing the geoscience knowledge required for sound regional planning and environmental protection of the National Capital Area. Based on an application developed by ESRI (Environmental System Research Institute), namely ArcIMS, the TSD has customized this web application to give free access to geoscience information of the Ottawa/Outaouais (Ontario/Québec) area including geological history, subsurface database, stratigraphy, bedrock, surficial and hydrogeology maps, and a few others. At present, each layer of geospatial information in TSD's interactive map viewer is connected to simple independent flat files (i.e. shapefiles), but it is also possible to connect GEOSERV to other types of (relational) databases (e.g. Microsoft SQL Server, Oracle). Frequent updating of shapefiles could be a cumbersome task, when new records are added, since we have to completely rebuild the updated shapefiles. However, new attributes can be added to existing shapefiles easily. At present, the updating process can not be done on-the-fly; we must stop and restart the updated MapService if one of its shapefiles is changed. The public can access seventeen MapServices that provide interactive tools that users can use to query, zoom, pan, select, and so on, or print the map displayed on their monitor. The map viewer is light-weight as it uses HTML and Javascript, so end users do not have to download and install any plug-ins. A free CD and a companion web site were also developed to give access to complementary information, like high resolution raster maps and reports. Some of the datasets are available free of charge, on-line.

Integration of rainfall/runoff and geomorphological analyses flood hazard in small catchments: case studies from the southern Apennines (Italy)

NASA Astrophysics Data System (ADS)

Palumbo, Manuela; Ascione, Alessandra; Santangelo, Nicoletta; Santo, Antonio

2017-04-01

We present the first results of an analysis of flood hazard in ungauged mountain catchments that are associated with intensely urbanized alluvial fans. Assessment of hydrological hazard has been based on the integration of rainfall/runoff modelling of drainage basins with geomorphological analysis and mapping. Some small and steep, ungauged mountain catchments located in various areas of the southern Apennines, in southern Italy, have been chosen as test sites. In the last centuries, the selected basins have been subject to heavy and intense precipitation events, which have caused flash floods with serious damages in the correlated alluvial fan areas. Available spatial information (regional technical maps, DEMs, land use maps, geological/lithological maps, orthophotos) and an automated GIS-based procedure (ArcGis tools and ArcHydro tools) have been used to extract morphological, hydrological and hydraulic parameters. Such parameters have been used to run the HEC (Hydrologic Engineering Center of the US Army Corps of Engineers) software (GeoHMS, GeoRAS, HMS and RAS) based on rainfall-runoff models, which have allowed the hydrological and hydraulic simulations. As the floods occurred in the studied catchments have been debris flows dominated, the solid load simulation has been also performed. In order to validate the simulations, we have compared results of the modelling with the effects produced by past floods. Such effects have been quantified through estimations of both the sediment volumes within each catchment that have the potential to be mobilised (pre-event) during a sediment transfer event, and the volume of sediments delivered by the debris flows at basins' outlets (post-event). The post-event sediment volume has been quantified through post-event surveys and Lidar data. Evaluation of the pre-event sediment volumes in single catchments has been based on mapping of sediment storages that may constitute source zones of bed load transport and debris flows. For such an approach has been used a methodology that consists of the application of a process-based geomorphological mapping, based on data derived from GIS analysis using high-resolution DEMs, field measurements and aerial photograph interpretations. Our integrated approach, which allows quantification of the flow rate and a semi-quantitative assessment of sediment that can be mobilized during hydro-meteorological events, is applied for the first time to torrential catchmenmts of the southern Apennines and may significantly contribute to previsional studies aimed at risk mitigation in the study region.

Intrusive Rock Database for the Digital Geologic Map of Utah

USGS Publications Warehouse

Nutt, C.J.; Ludington, Steve

2003-01-01

Digital geologic maps offer the promise of rapid and powerful answers to geologic questions using Geographic Information System software (GIS). Using modern GIS and database methods, a specialized derivative map can be easily prepared. An important limitation can be shortcomings in the information provided in the database associated with the digital map, a database which is often based on the legend of the original map. The purpose of this report is to show how the compilation of additional information can, when prepared as a database that can be used with the digital map, be used to create some types of derivative maps that are not possible with the original digital map and database. This Open-file Report consists of computer files with information about intrusive rocks in Utah that can be linked to the Digital Geologic Map of Utah (Hintze et al., 2000), an explanation of how to link the databases and map, and a list of references for the databases. The digital map, which represents the 1:500,000-scale Geologic Map of Utah (Hintze, 1980), can be obtained from the Utah Geological Survey (Map 179DM). Each polygon in the map has a unique identification number. We selected the polygons identified on the geologic map as intrusive rock, and constructed a database (UT_PLUT.xls) that classifies the polygons into plutonic map units (see tables). These plutonic map units are the key information that is used to relate the compiled information to the polygons on the map. The map includes a few polygons that were coded as intrusive on the state map but are largely volcanic rock; in these cases we note the volcanic rock names (rhyolite and latite) as used in the original sources Some polygons identified on the digital state map as intrusive rock were misidentified; these polygons are noted in a separate table of the database, along with some information about their true character. Fields may be empty because of lack of information from references used or difficulty in finding information. The information in the database is from a variety of sources, including geologic maps at scales ranging from 1:500,000 to 1:24,000, and thesis monographs. The references are shown twice: alphabetically and by region. The digital geologic map of Utah (Hintze and others, 2000) classifies intrusive rocks into only 3 categories, distinguished by age. They are: Ti, Tertiary intrusive rock; Ji, Upper to Middle Jurassic granite to quartz monzonite; and pCi, Early Proterozoic to Late Archean intrusive rock. Use of the tables provided in this report will permit selection and classification of those rocks by lithology and age. This database is a pilot study by the Survey and Analysis Project of the U.S. Geological Survey to characterize igneous rocks and link them to a digital map. The database, and others like it, will evolve as the project continues and other states are completed. We release this version now as an example, as a reference, and for those interested in Utah plutonic rocks.

Preliminary integrated geologic map databases for the United States: Digital data for the geology of southeast Alaska

USGS Publications Warehouse

Gehrels, George E.; Berg, Henry C.

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set of 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Digital Data for the reconnaissance geologic map for the Kuskokwim Bay Region of Southwest Alaska

USGS Publications Warehouse

Wilson, Frederic H.; Hults, Chad P.; Mohadjer, Solmaz; Coonrad, Warren L.; Shew, Nora B.; Labay, Keith A.

2008-01-01

INTRODUCTION The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

History as a guide to the future for cities: coastal storms and Jamaica Bay in New York City as an example.

NASA Astrophysics Data System (ADS)

Sanderson, E. W.; Orton, P. M.; Giampieri, M.; Spagnoli, C.

2015-12-01

History can provide a guide to the future by revealing the physical climatic and geomorphological dynamics with which cities must contend. We used historical maps from the U.S. Coast Survey and the Stevens Estuarine and Coastal Ocean Model (sECOM) to simulate how and where coastal flooding from storm surge affected the Jamaica Bay region of southeastern New York City at different points in time. This area, which houses approximately 1.2 million people today and the John F. Kennedy International Airport, was heavily impacted by coastal flooding during Hurricane Sandy. Historical analysis showed that the Rockaway Peninsula was an active barrier island system up until the early twentieth century, growing approximately 70 meters per year to the west between 1844 - 1891. Older historical maps made by American and European cartographers from 1524 - 1844 suggest that Jamaica Bay may have been a much more open system, with few or no interior marsh islands, at the time of European discovery. From these studies, we constructed digital terrain models and land cover maps for two historical periods: ca. 1870s and ca. 1609, and today. Storm simulations of hurricanes over the historical and present-day landscapes showed how a smaller inlet, shallower channel depths, and larger floodplains all can reduce the height of flooding inside the bay, and suggested a series of leverage experiments that test the efficacy of present-day green infrastructure interventions to lessen peak flood heights while maintaining tidal flushing. By combining history, modelling, and policy-relevant scenarios, we believe we have developed a reshreshing and accessible toolkit for policymakers thinking about resilience measures in coastal cities like New York.

Digital geologic map of part of the Thompson Falls 1:100,000 quadrangle, Idaho

USGS Publications Warehouse

Lewis, Reed S.; Derkey, Pamela D.

1999-01-01

The geology of the Thompson Falls 1:100,000 quadrangle, Idaho was compiled by Reed S. Lewis in 1997 onto a 1:100,000-scale greenline mylar of the topographic base map for input into a geographic information system (GIS). The resulting digital geologic map GIS can be queried in many ways to produce a variety of geologic maps. Digital base map data files (topography, roads, towns, rivers and lakes, etc.) are not included: they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:100,000 (e.g., 1:62,500 or 1:24,000). The map area is located in north Idaho. This open-file report describes the geologic map units, the methods used to convert the geologic map data into a digital format, the Arc/Info GIS file structures and relationships, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet.

Appearance of De Geer moraines in southern and western Finland - Implications for reconstructing glacier retreat dynamics

NASA Astrophysics Data System (ADS)

Ojala, Antti E. K.

2016-02-01

LiDAR digital elevation models (DEMs) from southern and western Finland were investigated to map and discriminate features of De Geer moraines, sparser and more scattered end moraines, and larger end moraine features (i.e., ice-marginal complexes). The results indicate that the occurrence and distribution of De Geer moraines and scattered end moraine ridges in Finland are more widespread than previously suggested. This is probably attributed to the ease of detecting and mapping these features with high-resolution DEMs, indicating the efficiency of LiDAR applications in geological and geomorphological studies. The variable appearance and distribution of moraine ridges in Finland support previous interpretations that no single model is likely to be appropriate for the genesis of De Geer moraines at all localities and for all types of end moraines. De Geer moraine appearances and interdistances probably result from a combination of the general rapidity of ice-margin recession during deglaciation, the proglacial water depth in which they were formed, and local glacier dynamics related to climate and terrain topography. The correlation between the varved clay-based rate of deglaciation and interdistances of distinct and regularly spaced De Geer moraine ridges indicates that the rate of deglaciation is probably involved in the De Geer ridge-forming process, but more thorough comparisons are needed to understand the extent to which De Geer interdistances represent an annual rate of ice-margin decay and the rapidity of regional deglaciation.

Application of Low-Cost Fixed-Wing UAV for Inland Lakes Shoreline Investigation

NASA Astrophysics Data System (ADS)

Templin, Tomasz; Popielarczyk, Dariusz; Kosecki, Rafał

2017-10-01

One of the most important factors that influences the performance of geomorphologic parameters on urban lakes is the water level. It fluctuates periodically, causing shoreline changes. It is especially significant for typical environmental studies like bathymetric surveys, morphometric parameters calculation, sediment depth changes, thermal structure, water quality monitoring, etc. In most reservoirs, it can be obtained from digitized historical maps or plans or directly measured using the instruments such as: geodetic total station, GNSS receivers, UAV with different sensors, satellite and aerial photos, terrestrial and airborne light detection and ranging, or others. Today one of the most popular measuring platforms, increasingly applied in many applications is UAV. Unmanned aerial system can be a cheap, easy to use, on-demand technology for gathering remote sensing data. Our study presents a reliable methodology for shallow lake shoreline investigation with the use of a low-cost fixed-wing UAV system. The research was implemented on a small, eutrophic urban inland reservoir located in the northern part of Poland—Lake Suskie. The geodetic TS, and RTK/GNSS measurements, hydroacoustic soundings and experimental aerial mapping were conducted by the authors in 2012-2015. The article specifically describes the UAV system used for experimental measurements, the obtained results and the accuracy analysis. Final conclusions demonstrate that even a low-cost fixed-wing UAV can provide an excellent tool for accurately surveying a shallow lake shoreline and generate valuable geoinformation data collected definitely faster than when traditional geodetic methods are employed.

Digital Geologic Map of the Rosalia 1:100,000 Quadrangle, Washington and Idaho: A Digital Database for the 1990 S.Z. Waggoner Map

USGS Publications Warehouse

Derkey, Pamela D.; Johnson, Bruce R.; Lackaff, Beatrice B.; Derkey, Robert E.

1998-01-01

The geologic map of the Rosalia 1:100,000-scale quadrangle was compiled in 1990 by S.Z. Waggoner of the Washington state Division of Geology and Earth Resources. This data was entered into a geographic information system (GIS) as part of a larger effort to create regional digital geology for the Pacific Northwest. The intent was to provide a digital geospatial database for a previously published black and white paper geologic map. This database can be queried in many ways to produce a variety of geologic maps. Digital base map data files are not included: they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:100,000 (e.g., 1:62,500 or 1:24,000) as it has been somewhat generalized to fit the 1:100,000 scale map. The map area is located in eastern Washington and extends across the state border into western Idaho. This open-file report describes the methods used to convert the geologic map data into a digital format, documents the file structures, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet. We wish to thank J. Eric Schuster of the Washington Division of Geology and Earth Resources for providing the original stable-base mylar and the funding for it to be scanned. We also thank Dick Blank and Barry Moring of the U.S. Geological Survey for reviewing the manuscript and digital files, respectively.

Influence of geomorphological properties and stage on in-stream travel time

NASA Astrophysics Data System (ADS)

Åkesson, Anna; Wörman, Anders

2014-05-01

The travel time distribution within stream channels is known to vary non-linearly with stage (discharge), depending on the combined effects of geomorphologic, hydrodynamic and kinematic dispersions. This non-linearity, implying that stream network travel time generally decreases with increasing discharge is a factor that is important to account for in hydrological modelling - especially when making peak flow predictions where uncertainty is often high and large values can be at risk. Through hydraulic analysis of several stream networks, we analyse how travel time distributions varies with discharge. The principal focus is the coupling to the geomorphologic properties of stream networks with the final goal being to use this physically based information as a parameterisation tool of the streamflow component of hydrologic models. For each of the studied stream networks, a 1D, steady-state, distributed routing model was set up to determine the velocities in each reach during different flow conditions. Although the model (based in the Manning friction formula) is built on the presence of uniform conditions within sub-reaches, the model can in the stream network scale be considered to include effects of non-uniformity as supercritical conditions in sections of the stream network give rise to backwater effects that reduce the flow velocities in upstream reaches in the stream. By coupling the routing model to a particle tracking routine tracing water "parcels" through the stream network, the average travel time within the stream network can be determined quantitatively for different flow conditions. The data used to drive the model is digitised stream network maps, topographical data (DEMs). The model is not calibrated in any way, but is run for with different sets of parameters representing a span of possible friction coefficients and cross-sectional geometries as this information is not generally known. The routing model is implemented in several different stream networks (representing catchments of the spatial scale of a few hundred km2) in different geographic regions in Sweden displaying different geomorphological properties. Results show that the geomorphological properties (data that is often available in the form of maps and/or DEMs) of individual stream networks have major influence on the stream network travel times. By coupling the geomorphological information to general expressions for stage dependency, catchment-specific relationships of how the travel times within stream networks can be determined. Basing the parameterisation procedure of a hydrological model in physical catchment properties and process understanding rather than statistical parameterisation (based in how a catchment has responded in the past) - is believed to lead to more reliable hydrological predictions - during extreme conditions as well as during changing conditions such as climate change and landscape modifications, and/or when making predictions in ungauged basins.

Understanding of the Geomorphological Elements in Discrimination of Typical Mediterranean Land Cover Types

NASA Astrophysics Data System (ADS)

Elhag, Mohamed; Boteva, Silvena

2017-12-01

Quantification of geomorphometric features is the keystone concern of the current study. The quantification was based on the statistical approach in term of multivariate analysis of local topographic features. The implemented algorithm utilizes the Digital Elevation Model (DEM) to categorize and extract the geomorphometric features embedded in the topographic dataset. The morphological settings were exercised on the central pixel of 3x3 per-defined convolution kernel to evaluate the surrounding pixels under the right directional pour point model (D8) of the azimuth viewpoints. Realization of unsupervised classification algorithm in term of Iterative Self-Organizing Data Analysis Technique (ISODATA) was carried out on ASTER GDEM within the boundary of the designated study area to distinguish 10 morphometric classes. The morphometric classes expressed spatial distribution variation in the study area. The adopted methodology is successful to appreciate the spatial distribution of the geomorphometric features under investigation. The conducted results verified the superimposition of the delineated geomorphometric elements over a given remote sensing imagery to be further analyzed. Robust relationship between different Land Cover types and the geomorphological elements was established in the context of the study area. The domination and the relative association of different Land Cover types in corresponding to its geomorphological elements were demonstrated.

Using Digital Mapping Tool in Ill-Structured Problem Solving

ERIC Educational Resources Information Center

Bai, Hua

2013-01-01

Scaffolding students' problem solving and helping them to improve problem solving skills are critical in instructional design courses. This study investigated the effects of students' uses of a digital mapping tool on their problem solving performance in a design case study. It was found that the students who used the digital mapping tool…

Using Digital Mapping Programs to Augment Student Learning in Social Studies

ERIC Educational Resources Information Center

Chandler, Thomas; An, Heejung

2007-01-01

Thomas Chandler and Heejung An describe how digital mapping technology can be incorporated into community-based K-12 social studies projects. According to Chandler and An, digital mapping can add value to the social studies curriculum by enabling students to better understand the interdependence between the lives of individuals and their…

Cartographic services contract...for everything geographic

USGS Publications Warehouse

,

2003-01-01

The U.S. Geological Survey's (USGS) Cartographic Services Contract (CSC) is used to award work for photogrammetric and mapping services under the umbrella of Architect-Engineer (A&E) contracting. The A&E contract is broad in scope and can accommodate any activity related to standard, nonstandard, graphic, and digital cartographic products. Services provided may include, but are not limited to, photogrammetric mapping and aerotriangulation; orthophotography; thematic mapping (for example, land characterization); analog and digital imagery applications; geographic information systems development; surveying and control acquisition, including ground-based and airborne Global Positioning System; analog and digital image manipulation, analysis, and interpretation; raster and vector map digitizing; data manipulations (for example, transformations, conversions, generalization, integration, and conflation); primary and ancillary data acquisition (for example, aerial photography, satellite imagery, multispectral, multitemporal, and hyperspectral data); image scanning and processing; metadata production, revision, and creation; and production or revision of standard USGS products defined by formal and informal specification and standards, such as those for digital line graphs, digital elevation models, digital orthophoto quadrangles, and digital raster graphics.

The Gravitational Process Path (GPP) model (v1.0) - a GIS-based simulation framework for gravitational processes

NASA Astrophysics Data System (ADS)

Wichmann, Volker

2017-09-01

The Gravitational Process Path (GPP) model can be used to simulate the process path and run-out area of gravitational processes based on a digital terrain model (DTM). The conceptual model combines several components (process path, run-out length, sink filling and material deposition) to simulate the movement of a mass point from an initiation site to the deposition area. For each component several modeling approaches are provided, which makes the tool configurable for different processes such as rockfall, debris flows or snow avalanches. The tool can be applied to regional-scale studies such as natural hazard susceptibility mapping but also contains components for scenario-based modeling of single events. Both the modeling approaches and precursor implementations of the tool have proven their applicability in numerous studies, also including geomorphological research questions such as the delineation of sediment cascades or the study of process connectivity. This is the first open-source implementation, completely re-written, extended and improved in many ways. The tool has been committed to the main repository of the System for Automated Geoscientific Analyses (SAGA) and thus will be available with every SAGA release.

Vegetation survey in Amazonia using LANDSAT data. [Brazil

NASA Technical Reports Server (NTRS)

Parada, N. D. J. (Principal Investigator); Shimabukuro, Y. E.; Dossantos, J. R.; Deaquino, L. C. S.

1982-01-01

Automatic Image-100 analysis of LANDSAT data was performed using the MAXVER classification algorithm. In the pilot area, four vegetation units were mapped automatically in addition to the areas occupied for agricultural activities. The Image-100 classified results together with a soil map and information from RADAR images, permitted the establishment of the final legend with six classes: semi-deciduous tropical forest; low land evergreen tropical forest; secondary vegetation; tropical forest of humid areas, predominant pastureland and flood plains. Two water types were identified based on their sediments indicating different geological and geomorphological aspects.

How a geomorphosite inventory can contribute to regional sustainable development? The case of the Simen Mountains National Park, Ethiopia

NASA Astrophysics Data System (ADS)

Mauerhofer, Lukas; Reynard, Emmanuel; Asrat, Asfawossen; Hurni, Hans; Wildlife Conservation Authority, Ethiopian

2016-04-01

This research aimed at investigating how an inventory of geomorphosites can foster or improve the knowledge and management of geomorphological heritages in the context of developing countries. Accordingly, a geomorphosite inventory in the Simen Mountains National Park (SMNP), Ethiopia was conducted following the method of Reynard et al. (2015). The national context of geoheritage and geoconservation in Ethiopia was appraised and a road map for the management of the inventoried sites in the SMNP was elaborated. Ethiopia hosts numerous geoheritage sites, some of which of highest international significance. Therefore, geotourism has recently been promoted throughout the country (Asrat et al., 2008). Despite numerous trials of the scientific community, there is not yet a national policy for geoconservation in the country. Many parts of Ethiopia are underdeveloped in terms of economic subsistence and infrastructure, making these immediate priorities over conservation efforts. Nevertheless, this study showed that the Simen Mountains have the potential to become a UNESCO Global Geopark and that geosites could be used to develop geotourism within SMNP, and that development and conservation are not contradictory. Twenty-one geomorphosites were identified and assessed. Diverse geomorphological contexts including fluvial, structural, glacial, periglacial, anthropic and organic characterize the SMNP. The temporal stages, which allow the reconstitution of the morphogenesis of the Simen Mountains, are the Cenozoic volcanism, Last Glacial Maximum, Holocene as well as historic/modern landscape modification. Four synthesis maps were elaborated to present the results of the assessment. The average scientific value of the inventoried geomorphosites is very high compared to other inventories realized using the same method. This is particularly due to the extremely high integrity of the sites. Almost all geomorphosites are in a good state of conservation and only few sites are vulnerable to human encroachment. The educational interest of most sites is high but interpretation facilities are absent. With some minor adjustments, the application of the inventory method (Reynard et al., 2015) to the SMNP has proven successful and can be recommended for application to other areas in developing countries of similar well-documented geomorphology. However, the method could prove too complex for areas where basic knowledge on geomorphology is poor, as is often the case in developing countries. Based on previous studies (in particular Asrat et al. 2012) and results of the current inventory, a road map for SMNP geomorphosite management was proposed. Eight strategic objectives and working tasks were considered, which include the development of geotourism products such as geotourist maps, geo-trails and guidebooks, geo-trekking, geo-sightseeing tours, and interpretive panels as well as the training of geo-guides and capacity building of the park staff and specific management of the Lemalemo site, one of the most accessible geosites in the park. The overall goal is to raise awareness on the rich geomorphological heritage through geotourism development and empowerment of locals and thus to contribute to long-term protection of the geomorphosites. In conclusion the study revealed important potential for sustainable rural development in the Simen. Applied research will be necessary on how exactly the promotion products should be developed. References Asrat, A., Demissie, M., Mogessie, A. (2008). Geotourism in Ethiopia: archaelogical and ancient cities, religious and cultural centres: Yeha, Axum, Wukro, and Lalibela. Addis Ababa: Shama Books. Asrat, A., Demissie, M., Mogessie, A. (2012). Geoheritage conservation in Ethiopia: the case of the Simien Mountains. Quaestiones Geographicae, 31(1), 7-23. doi:10.2478/v10117-012-0001-0. Reynard E., Perret A., Bussard J., Grangier L., Martin S. (2015). Integrated approach for the inventory and management of geomorphological heritage at the regional scale. Geoheritage, doi: 10.1007/s12371-015-0153-0

A Double Perturbation Method for Reducing Dynamical Degradation of the Digital Baker Map

NASA Astrophysics Data System (ADS)

Liu, Lingfeng; Lin, Jun; Miao, Suoxia; Liu, Bocheng

2017-06-01

The digital Baker map is widely used in different kinds of cryptosystems, especially for image encryption. However, any chaotic map which is realized on the finite precision device (e.g. computer) will suffer from dynamical degradation, which refers to short cycle lengths, low complexity and strong correlations. In this paper, a novel double perturbation method is proposed for reducing the dynamical degradation of the digital Baker map. Both state variables and system parameters are perturbed by the digital logistic map. Numerical experiments show that the perturbed Baker map can achieve good statistical and cryptographic properties. Furthermore, a new image encryption algorithm is provided as a simple application. With a rather simple algorithm, the encrypted image can achieve high security, which is competitive to the recently proposed image encryption algorithms.

Susceptibility mapping in the Río El Estado watershed, Pico de Orizaba volcano, Mexico

NASA Astrophysics Data System (ADS)

Legorreta Paulin, G.; Bursik, M. I.; Lugo Hubp, J.; Paredes Mejía, L.; Aceves Quesada, F.

2013-12-01

In volcanic terrains, dormant stratovolcanoes are very common and can trigger landslides and debris flows continually along stream systems, thereby affecting human settlements and economic activities. It is important to assess their potential impact and damage through the use of landslide inventory maps and landslide models. This poster provides an overview of the on-going research project (Grant SEP-CONACYT no 167495) from the Institute of Geography at the National Autonomous University of Mexico (UNAM) that seeks to conduct a multi-temporal landslide inventory and produce a landslide susceptibility map by using Geographic Information Systems (GIS). The Río El Estado watershed on the southwestern flank of Pico de Orizaba volcano, the highest mountain in Mexico, is selected as a study area. The catchment covers 5.2 km2 with elevations ranging from 2676.79 to 4248.2 m a.s.l. and hillslopes between 5° and 56°. The stream system of Río El Estado catchment erodes Tertiary and Quaternary lavas, pyroclastic flows, and fall deposits. The geologic and geomorphologic factors in combination with high seasonal precipitation, high degree of weathering, and steep slopes predispose the study area to landslides. The method encompasses two main levels of analysis to assess landslide susceptibility. The first level builds a historic landslide inventory. In the study area, an inventory of more than 100 landslides was mapped from interpretation of multi-temporal aerial orthophotographs and local field surveys to assess and describe landslide distribution. All landslides were digitized into a GIS, and the spatial geo-database of landslides was constructed from standardized GIS datasets. The second level calculates the susceptibility for the watershed. Multiple Logistic Regression (MLR) was used to examine the relationship between landsliding and several independent variables (elevation, slope, terrain curvature, flow direction, saturation, contributing area, land use, and geology) to create the susceptibility map. Finally, the model was compared with the reality expressed by the inventory map. The technique and its implementation of each level in a GIS-based technology is presented and discussed.

Successful Teaching, Learning, and Use of Digital Mapping Technology in Mazvihwa, Rural Zimbabwe

NASA Astrophysics Data System (ADS)

Eitzel Solera, M. V.; Madzoro, S.; Solera, J.; Mhike Hove, E.; Changarara, A.; Ndlovu, D.; Chirindira, A.; Ndlovu, A.; Gwatipedza, S.; Mhizha, M.; Ndlovu, M.

2016-12-01

Participatory mapping is now a staple of community-based work around the world. Particularly for indigenous and rural peoples, it can represent a new avenue for environmental justice and can be a tool for culturally appropriate management of local ecosystems. We present a successful example of teaching and learning digital mapping technology in rural Zimbabwe. Our digital mapping project is part of the long-term community-based participatory research of The Muonde Trust in Mazvihwa, Zimbabwe. By gathering and distributing local knowledge and also bringing in visitors to share knowledge, Muonde has been able to spread relevant information among rural farmers. The authors were all members of Muonde or were Muonde's visitors, and were mentors and learners of digital mapping technologies at different times. Key successful characteristics of participants included patience, compassion, openness, perseverance, respect, and humility. Important mentoring strategies included: 1) instruction in Shona and in English, 2) locally relevant examples, assignments, and analogies motivated by real needs, 3) using a variety of teaching methods for different learning modalities, 4) building on and modifying familiar teaching methods, and 5) paying attention to the social and relational aspects of teaching and learning. The Muonde mapping team has used their new skills for a wide variety of purposes, including: identifying, discussing, and acting on emerging needs; using digital mapping for land-use and agropastoral planning; and using mapping as a tool for recording and telling important historical and cultural stories. Digital mapping has built self-confidence as well as providing employable skills and giving Muonde more visibility to other local and national non-governmental organizations, utility companies, and educational institutions. Digital mapping, as taught in a bottom-up, collaborative way, has proven to be both accessible and of enormous practical use to rural Zimbabweans.

Geologic map of the eastern part of the Challis National Forest and vicinity, Idaho

USGS Publications Warehouse

Wilson, A.B.; Skipp, B.A.

1994-01-01

The paper version of the Geologic Map of the eastern part of the Challis National Forest and vicinity, Idaho was compiled by Anna Wilson and Betty Skipp in 1994. The geology was compiled on a 1:250,000 scale topographic base map. TechniGraphic System, Inc. of Fort Collins Colorado digitized this map under contract for N.Shock. G.Green edited and prepared the digital version for publication as a GIS database. The digital geologic map database can be queried in many ways to produce a variety of geologic maps.

Planetary mapping—The datamodel's perspective and GIS framework

NASA Astrophysics Data System (ADS)

van Gasselt, S.; Nass, A.

2011-09-01

Demands for a broad range of integrated geospatial data-analysis tools and methods for planetary data organization have been growing considerably since the late 1990s when a plethora of missions equipped with new instruments entered planetary orbits or landed on the surface. They sent back terabytes of new data which soon became accessible for the scientific community and public and which needed to be organized. On the terrestrial side, issues of data access, organization and utilization for scientific and economic analyses are handled by using a range of well-established geographic information systems (GIS) that also found their way into the field of planetary sciences in the late 1990s. We here address key issues concerning the field of planetary mapping by making use of established GIS environments and discuss methods of addressing data organization and mapping requirements by using an easily integrable datamodel that is - for the time being - designed as file-geodatabase (FileGDB) environment in ESRI's ArcGIS. A major design-driving requirement for this datamodel is its extensibility and scalability for growing scientific as well as technical needs, e.g., the utilization of such a datamodel for surface mapping of different planetary objects as defined by their respective reference system and by using different instrument data. Furthermore, it is a major goal to construct a generic model which allows to perform combined geologic as well as geomorphologic mapping tasks making use of international standards without loss of information and by maintaining topologic integrity. An integration of such a datamodel within a geospatial DBMS context can practically be performed by individuals as well as groups without having to deal with the details of administrative tasks and data ingestion issues. Besides the actual mapping, key components of such a mapping datamodel deal with the organization and search for image-sensor data and previous mapping efforts, as well as the proper organization of cartographic representations and assignments of geologic/geomorphologic units within their stratigraphic context.

Geologic Mapping of the Chaac-Camaxtli Region of Io from Galileo Imaging Data

NASA Technical Reports Server (NTRS)

Williams, David A.; Radebaugh, Jani; Keszthelyi, Laszlo P.; McEwen, Alfred S.; Lopes, Rosaly M. C.; Doute, Sylvain; Greekely, Ronald

2003-01-01

We produced a geologic/geomorphologic map of the Chaac-Camaxtli region of Io's leading anti-Jovian hemisphere using regional resolution ( 186 m/pixel) Galileo imaging data collected during orbit I27 (February 2000) integrated with lower resolution (1.4 km/pixel) color data, along with other Galileo imaging and spectral data. This is the first regional map of Io made from Galileo data. Nine color and geomorphologic units have been mapped, and the close proximity of dark and various colored bright materials suggests that there is an intimate interaction between (presumably) silicate magmas and sulfur-bearing volatile materials that produced a variety of explosive and effusive deposits in the recent geologic past. This region of Io is dominated by 11 volcanic centers, most of which are paterae that are analogous in morphology to terrestrial calderas but larger in size. Mapping of structural features indicates that most of the active regions occur in topographic lows, and less active or inactive paterae are associated with topographic highs. This indicates that crustal thickness variations influence magma access to the surface. Surface changes in this region since the Voyager flybys are relatively minor (additional bright and dark flows, color changes), although several active vents have migrated within paterae. This observation, along with the identification of the relatively regular spacing of paterae (approx. 100 - 150 km) along a line, may indicate there are multiple interlacing fractures in the crust that serve as magma conduits from the interior. This connection between volcanism and tectonism may have implications for tidal heating mechanisms and their effect on Io's lithosphere. Some inactive patera floors may be evolving into bright plains material, which, if composed of silicates, might explain the strength of Io's crust to support steep patera walls and tall mountains.

Geologic Mapping of the Chaac-Camaxtli Region of Io from Galileo Imaging Data

NASA Technical Reports Server (NTRS)

Williams, David A.; Radebaugh, Jani; Keszthelyi, Laszlo P.; McEwen, Alfred S.; Lopes, Rosaly M. C.; Doute, Sylvain; Greeley, Ronald

2002-01-01

We produced a geologic/geomorphologic map of the Chaac-Camaxtli region of Io's leading anti-Jovian hemisphere using regional resolution (186 m/pixel) Galileo imaging data collected during orbit I27 (February 2000) integrated with lower resolution (1.4 km/pixel) color data, along with other Galileo imaging and spectral data. This is the first regional map of Io made from Galileo data. Nine color and geomorphologic units have been mapped, and the close proximity of dark and various colored bright materials suggests that there is an intimate interaction between (presumably) silicate magmas and sulfur-bearing volatile materials that produced a variety of explosive and effusive deposits in the recent geologic past. This region of Io is dominated by 11 volcanic centers, most of which are paterae that are analogous in morphology to terrestrial calderas but larger in size. Mapping of structural features indicates that most of the active regions occur in topographic lows, and less active or inactive paterae are associated with topographic highs. This indicates that crustal thickness variations influence magma access to the surface. Surface changes in this region since the Voyager flybys (1979) are relatively minor (additional bright and dark flows, color changes), although several active vents have migrated within paterae. This observation, along with the identification of the relatively regular spacing of paterae (approx. 100- 150 km) along a line, may indicate there are multiple interlacing fractures in the crust that serve as magma conduits from the interior. This connection between volcanism and tectonism may have implications for tidal heating mechanisms and their effect on Io's lithosphere. Some inactive patera floors may be evolving into bright plains material, which, if composed of silicates, might explain the strength of Io's crust to support steep patera walls and tall mountains.

Use of Digital Elevation Models to understand map landforms and history of the magmatism Khibiny Massif (Kola Peninsula, Russia)

NASA Astrophysics Data System (ADS)

Chesalova, Elena; Asavin, Alex

2016-04-01

This work presents an improved geomorphological methodology that uses 3D model of relief, remotely-sensed data, geological, geophysical maps and tools of Geographical Information Systems. On the basis of maps of 1: 50,000 and 1: 200,000 the Digital Elevation model (DEM) of Khibiny massif was developed. We used software ARC / INFO v10.2 ESRI. A DEM was used for analyzing landform by extracting the slope gradient, curvature, valley pro?les, slope, aspect and so on. The results were gradually re?ned from the interpretation of satellite imagery and geological map Geomorphological analysis will allow us to determine spatial regularities in inner massive construction. We try to found areas where gas emissions (CH4/H2) enrich, according to morphometry, geology, tectonic and other environments. The main regional blocks were de?ned by different morphological evidences: impression zone, similar to subsidence caldera; uplift zone, domed area (located in the highest part of massif and zone of intersection of main faults) and others. It says that there are the few stages in the development of the Khibiny massif. There is no common concept of the consequence of intrudes magmatic phases now. And we hope that our geomorphical analysis take a new evidences about this problems. Locations of the blocks' borders (tectonic zones) were recognized by lineament analysis of valleys and tectonic faults presented in relief. Erosion system is represented by valleys of 4 ranks. It inherits the zone of tectonic disturbances 3 groups of faults were recognized: 1) Global lineament system cross whole peninsula - existing before Khibiny massif intrusion; 2) Faults associated with the formation of the intrusive phases sequence and magma differentiation and with later collision history during magma cooling; 3) Crack system related to neotectonic process. We believed that if different magmatic phases intrude in similar tectonic environment, the common spatial system of faults will be formed. Really we observed a confederated system of contraction faults for different phases suggests that the differentiation within the intrusion is implemented as a single magma chamber for different intrusive phases. It remains an open question - which fault system (old or young) is more productive to gas emissions? The discrepancy of the geological structures and land forms is established. • Impression zone is represented by foyaites (high-strength rocks) • Uplift zone - rischorrites, khibinites (low-strength rocks) • Trough valley - weakened zone of tectonic faults - yuvites, urtites, rischorrites (low-strength rocks) • In the lowest part of depression zone - carbonatite stock It looks like an inversion of lithomorphic properties and the rock's morphological expression - it is a subject to uplift tectonics. Positive forms of relief (domed area and swells) could be formed due to the intrusion of secondary highly differentiated melts of low density. Also our early studies con?rm that rischorrites is one of the more rich ?uid gases rocks in Khibina massive. And we expect the strong emission of gas in the areas of distribution of these rock. Low density and increase buoyancy of magma, as a result of high gas concentration, can increase difference between density of cumulus minerals and intercumulus melts. This inversion between melt density and cumulus density, which are formed during chamber melt differentiation, and their low viscosity can cause formation of the local swells. Swells are located in the areas of crossing tectonic faults. This can lead to vertical movements, caused by elevating power of micro diapirs. Such diapirs forms are observed on the block diagrams of apatite ores in Koashve (Ivanyuk et. al., 2012). We observe such structure in middle zone of Khibiny massif, near Kuelporr deposit, about 15 km long and 5 km width and one with less size near Rasvumchorr deposit, about 10x3 km. This is the area of rischorrite's appearance. And in this area we see locations of the most intense free gas emission. The technical possibilities that are offered by Remote Sensing (RS) and Geographical Information Systems (GIS) facilitate the geomorphological investigation of inhospitable and inaccessible mountain areas Digital Elevation Models (DEMs) are valuable tools for approximation of the real world's continuous surface. They allow a visual analysis of the earth's surface morphology, quanti?cation of sediment volumes and the calculation of topographic derivatives such as the slope gradient, slope aspect and pro?le curvature that consume ?eld investigations and optimize time The project has been sponsored by programmm Presidium of RAS P44. Reference Ivanyuk G, Kalashnikov A, Mikhailova J, Konoplyova N, Goryainov P, Yakovenchuk V, Pakhomovsky Y. Self-Organization of the Khibiny Alkaline Massif (Kola Peninsula, Russia). In Earth Sciences, Dr. Imran Ahmad Dar(Ed.), ISBN: 978-953-307-861-8, InTech, Available from: http://www.intechopen.com/books/earth-sciences/self-organization-of-the-khibiny-alkaline -massif -kolapeninsula-russia INTECH Open Access Publisher; 2012, Head7, P.131-156.

Flexible, reconfigurable, power efficient transmitter and method

NASA Technical Reports Server (NTRS)

Bishop, James W. (Inventor); Zaki, Nazrul H. Mohd (Inventor); Newman, David Childress (Inventor); Bundick, Steven N. (Inventor)

2011-01-01

A flexible, reconfigurable, power efficient transmitter device and method is provided. In one embodiment, the method includes receiving outbound data and determining a mode of operation. When operating in a first mode the method may include modulation mapping the outbound data according a modulation scheme to provide first modulation mapped digital data, converting the first modulation mapped digital data to an analog signal that comprises an intermediate frequency (IF) analog signal, upconverting the IF analog signal to produce a first modulated radio frequency (RF) signal based on a local oscillator signal, amplifying the first RF modulated signal to produce a first RF output signal, and outputting the first RF output signal via an isolator. In a second mode of operation method may include modulation mapping the outbound data according a modulation scheme to provide second modulation mapped digital data, converting the second modulation mapped digital data to a first digital baseband signal, conditioning the first digital baseband signal to provide a first analog baseband signal, modulating one or more carriers with the first analog baseband signal to produce a second modulated RF signal based on a local oscillator signal, amplifying the second RF modulated signal to produce a second RF output signal, and outputting the second RF output signal via the isolator. The digital baseband signal may comprise an in-phase (I) digital baseband signal and a quadrature (Q) baseband signal.

Digital Mapping Techniques '07 - Workshop Proceedings

USGS Publications Warehouse

Soller, David R.

2008-01-01

The Digital Mapping Techniques '07 (DMT'07) workshop was attended by 85 technical experts from 49 agencies, universities, and private companies, including representatives from 27 state geological surveys. This year's meeting, the tenth in the annual series, was hosted by the South Carolina Geological Survey, from May 20-23, 2007, on the University of South Carolina campus in Columbia, South Carolina. Each DMT workshop has been coordinated by the U.S. Geological Survey's National Geologic Map Database Project and the Association of American State Geologists (AASG). As in previous year's meetings, the objective was to foster informal discussion and exchange of technical information, principally in order to develop more efficient methods for digital mapping, cartography, GIS analysis, and information management. At this meeting, oral and poster presentations and special discussion sessions emphasized: 1) methods for creating and publishing map products (here, 'publishing' includes Web-based release); 2) field data capture software and techniques, including the use of LIDAR; 3) digital cartographic techniques; 4) migration of digital maps into ArcGIS Geodatabase format; 5) analytical GIS techniques; and 6) continued development of the National Geologic Map Database.

Hydro-geomorphic connectivity and landslide features extraction to identifying potential threats and hazardous areas

NASA Astrophysics Data System (ADS)

Tarolli, Paolo; Fuller, Ian C.; Basso, Federica; Cavalli, Marco; Sofia, Giulia

2017-04-01

Hydro-geomorphic connectivity has significantly emerged as a new concept to understand the transfer of surface water and sediment through landscapes. A further scientific challenge is determining how the concept can be used to enable sustainable land and water management. This research proposes an interesting approach to integrating remote sensing techniques, connectivity theory, and geomorphometry based on high-resolution digital terrain model (HR-DTMs) to automatically extract landslides crowns and gully erosion, to determine the different rate of connectivity among the main extracted features and the river network, and thus determine a possible categorization of hazardous areas. The study takes place in two mountainous regions in the Wellington Region (New Zealand). The methodology is a three step approach. Firstly, we performed an automatic detection of the likely landslides crowns through the use of thresholds obtained by the statistical analysis of the variability of landform curvature. After that, the research considered the Connectivity Index to analyse how a complex and rugged topography induces large variations in erosion and sediment delivery in the two catchments. Lastly, the two methods have been integrated to create a unique procedure able to classify the different rate of connectivity among the main features and the river network and thus identifying potential threats and hazardous areas. The methodology is fast, and it can produce a detailed and updated inventory map that could be a key tool for erosional and sediment delivery hazard mitigation. This fast and simple method can be a useful tool to manage emergencies giving priorities to more failure-prone zones. Furthermore, it could be considered to do a preliminary interpretations of geomorphological phenomena and more in general, it could be the base to develop inventory maps. References Cavalli M, Trevisani S, Comiti F, Marchi L. 2013. Geomorphometric assessment of spatial sediment connectivity in small Alpine catchments. Geomorphology 188: 31-41 DOI: 10.1016/j.geomorph.2012.05.007 Sofia G, Dalla Fontana G, Tarolli P. 2014. High-resolution topography and anthropogenic feature extraction: testing geomorphometric parameters in floodplains. Hydrological Processes 28 (4): 2046-2061 DOI: 10.1002/hyp.9727 Tarolli P, Sofia G, Dalla Fontana G. 2012. Geomorphic features extraction from high-resolution topography: landslide crowns and bank erosion. Natural Hazards 61 (1): 65-83 DOI: 10.1007/s11069-010-9695-2

Research on the Application of Rapid Surveying and Mapping for Large Scare Topographic Map by Uav Aerial Photography System

NASA Astrophysics Data System (ADS)

Gao, Z.; Song, Y.; Li, C.; Zeng, F.; Wang, F.

2017-08-01

Rapid acquisition and processing method of large scale topographic map data, which relies on the Unmanned Aerial Vehicle (UAV) low-altitude aerial photogrammetry system, is studied in this paper, elaborating the main work flow. Key technologies of UAV photograph mapping is also studied, developing a rapid mapping system based on electronic plate mapping system, thus changing the traditional mapping mode and greatly improving the efficiency of the mapping. Production test and achievement precision evaluation of Digital Orth photo Map (DOM), Digital Line Graphic (DLG) and other digital production were carried out combined with the city basic topographic map update project, which provides a new techniques for large scale rapid surveying and has obvious technical advantage and good application prospect.

Fusion of Remote Sensing Methods, UAV Photogrammetry and LiDAR Scanning products for monitoring fluvial dynamics

NASA Astrophysics Data System (ADS)

Lendzioch, Theodora; Langhammer, Jakub; Hartvich, Filip

2015-04-01

Fusion of remote sensing data is a common and rapidly developing discipline, which combines data from multiple sources with different spatial and spectral resolution, from satellite sensors, aircraft and ground platforms. Fusion data contains more detailed information than each of the source and enhances the interpretation performance and accuracy of the source data and produces a high-quality visualisation of the final data. Especially, in fluvial geomorphology it is essential to get valuable images in sub-meter resolution to obtain high quality 2D and 3D information for a detailed identification, extraction and description of channel features of different river regimes and to perform a rapid mapping of changes in river topography. In order to design, test and evaluate a new approach for detection of river morphology, we combine different research techniques from remote sensing products to drone-based photogrammetry and LiDAR products (aerial LiDAR Scanner and TLS). Topographic information (e.g. changes in river channel morphology, surface roughness, evaluation of floodplain inundation, mapping gravel bars and slope characteristics) will be extracted either from one single layer or from combined layers in accordance to detect fluvial topographic changes before and after flood events. Besides statistical approaches for predictive geomorphological mapping and the determination of errors and uncertainties of the data, we will also provide 3D modelling of small fluvial features.

Landslide susceptibility mapping in Mawat area, Kurdistan Region, NE Iraq: a comparison of different statistical models

NASA Astrophysics Data System (ADS)

Othman, A. A.; Gloaguen, R.; Andreani, L.; Rahnama, M.

2015-03-01

During the last decades, expansion of settlements into areas prone to landslides in Iraq has increased the importance of accurate hazard assessment. Susceptibility mapping provides information about hazardous locations and thus helps to potentially prevent infrastructure damage due to mass wasting. The aim of this study is to evaluate and compare frequency ratio (FR), weight of evidence (WOE), logistic regression (LR) and probit regression (PR) approaches in combination with new geomorphological indices to determine the landslide susceptibility index (LSI). We tested these four methods in Mawat area, Kurdistan Region, NE Iraq, where landslides occur frequently. For this purpose, we evaluated 16 geomorphological, geological and environmental predicting factors mainly derived from the advanced spaceborne thermal emission and reflection radiometer (ASTER) satellite. The available reference inventory includes 351 landslides representing a cumulative surface of 3.127 km2. This reference inventory was mapped from QuickBird data by manual delineation and partly verified by field survey. The areas under curve (AUC) of the receiver operating characteristic (ROC), and relative landslide density (R index) show that all models perform similarly and that focus should be put on the careful selection of proxies. The results indicate that the lithology and the slope aspects play major roles for landslide occurrences. Furthermore, this paper demonstrates that using hypsometric integral as a prediction factor instead of slope curvature gives better results and increases the accuracy of the LSI.

Surface Rupture Map of the 2002 M7.9 Denali Fault Earthquake, Alaska: Digital Data

USGS Publications Warehouse

Haeussler, Peter J.

2009-01-01

The November 3, 2002, Mw7.9 Denali Fault earthquake produced about 340 km of surface rupture along the Susitna Glacier Thrust Fault and the right-lateral, strike-slip Denali and Totschunda Faults. Digital photogrammetric methods were primarily used to create a 1:500-scale, three-dimensional surface rupture map, and 1:6,000-scale aerial photographs were used for three-dimensional digitization in ESRI's ArcMap GIS software, using Leica's StereoAnalyst plug in. Points were digitized 4.3 m apart, on average, for the entire surface rupture. Earthquake-induced landslides, sackungen, and unruptured Holocene fault scarps on the eastern Denali Fault were also digitized where they lay within the limits of air photo coverage. This digital three-dimensional fault-trace map is superior to traditional maps in terms of relative and absolute accuracy, completeness, and detail and is used as a basis for three-dimensional visualization. Field work complements the air photo observations in locations of dense vegetation, on bedrock, or in areas where the surface trace is weakly developed. Seventeen km of the fault trace, which broke through glacier ice, were not digitized in detail due to time constraints, and air photos missed another 10 km of fault rupture through the upper Black Rapids Glacier, so that was not mapped in detail either.

Integrated terrain mapping with digital Landsat images in Queensland, Australia

USGS Publications Warehouse

Robinove, Charles Joseph

1979-01-01

Mapping with Landsat images usually is done by selecting single types of features, such as soils, vegetation, or rocks, and creating visually interpreted or digitally classified maps of each feature. Individual maps can then be overlaid on or combined with other maps to characterize the terrain. Integrated terrain mapping combines several terrain features into each map unit which, in many cases, is more directly related to uses of the land and to methods of land management than the single features alone. Terrain brightness, as measured by the multispectral scanners in Landsat 1 and 2, represents an integration of reflectance from the terrain features within the scanner's instantaneous field of view and is therefore more correlatable with integrated terrain units than with differentiated ones, such as rocks, soils, and vegetation. A test of the feasibilty of the technique of mapping integrated terrain units was conducted in a part of southwestern Queensland, Australia, in cooperation with scientists of the Queensland Department of Primary Industries. The primary purpose was to test the use of digital classification techniques to create a 'land systems map' usable for grazing land management. A recently published map of 'land systems' in the area (made by aerial photograph interpretation and ground surveys), which are integrated terrain units composed of vegetation, soil, topography, and geomorphic features, was used as a basis for comparison with digitally classified Landsat multispectral images. The land systems, in turn, each have a specific grazing capacity for cattle (expressed in beasts per km 2 ) which is estimated following analysis of both research results and property carrying capacities. Landsat images, in computer-compatible tape form, were first contrast-stretched to increase their visual interpretability, and digitally classified by the parallelepiped method into distinct spectral classes to determine their correspondence to the land systems classes and to areally smaller, but readily recognizable, 'land units.' Many land systems appeared as distinct spectral classes or as acceptably homogeneous combinations of several spectral classes. The digitally classified map corresponded to the general geographic patterns of many of the land systems. Statistical correlation of the digitally classified map and the published map was not possible because the published map showed only land systems whereas the digitally classified map showed some land units as well as systems. The general correspondence of spectral classes to the integrated terrain units means that the digital mapping of the units may precede fieldwork and act as a guide to field sampling and detailed terrain unit description as well as measuring of the location, area, and extent of each unit. Extension of the Landsat mapping and classification technique to other arid and semi-arid regions of the world may be feasible.

Mapping Eroded Areas on Mountain Grassland with Terrestrial Photogrammetry and Object-Based Image Analysis

NASA Astrophysics Data System (ADS)

Mayr, Andreas; Rutzinger, Martin; Bremer, Magnus; Geitner, Clemens

2016-06-01

In the Alps as well as in other mountain regions steep grassland is frequently affected by shallow erosion. Often small landslides or snow movements displace the vegetation together with soil and/or unconsolidated material. This results in bare earth surface patches within the grass covered slope. Close-range and remote sensing techniques are promising for both mapping and monitoring these eroded areas. This is essential for a better geomorphological process understanding, to assess past and recent developments, and to plan mitigation measures. Recent developments in image matching techniques make it feasible to produce high resolution orthophotos and digital elevation models from terrestrial oblique images. In this paper we propose to delineate the boundary of eroded areas for selected scenes of a study area, using close-range photogrammetric data. Striving for an efficient, objective and reproducible workflow for this task, we developed an approach for automated classification of the scenes into the classes grass and eroded. We propose an object-based image analysis (OBIA) workflow which consists of image segmentation and automated threshold selection for classification using the Excess Green Vegetation Index (ExG). The automated workflow is tested with ten different scenes. Compared to a manual classification, grass and eroded areas are classified with an overall accuracy between 90.7% and 95.5%, depending on the scene. The methods proved to be insensitive to differences in illumination of the scenes and greenness of the grass. The proposed workflow reduces user interaction and is transferable to other study areas. We conclude that close-range photogrammetry is a valuable low-cost tool for mapping this type of eroded areas in the field with a high level of detail and quality. In future, the output will be used as ground truth for an area-wide mapping of eroded areas in coarser resolution aerial orthophotos acquired at the same time.

Utility of shallow-water ATRIS images in defining biogeologic processes and self-similarity in skeletal scleractinia, Florida reefs

USGS Publications Warehouse

Lidz, B.H.; Brock, J.C.; Nagle, D.B.

2008-01-01

A recently developed remote-sensing instrument acquires high-quality digital photographs in shallow-marine settings within water depths of 15 m. The technology, known as the Along-Track Reef-Imaging System, provides remarkably clear, georeferenced imagery that allows visual interpretation of benthic class (substrates, organisms) for mapping coral reef habitats, as intended. Unforeseen, however, are functions new to the initial technologic purpose: interpr??table evidence for real-time biogeologic processes and for perception of scaled-up skeletal self-similarity of scleractinian microstructure. Florida reef sea trials lacked the grid structure required to map contiguous habitat and submarine topography. Thus, only general observations could be made relative to times and sites of imagery. Degradation of corals was nearly universal; absence of reef fish was profound. However, ???1% of more than 23,600 sea-trial images examined provided visual evidence for local environs and processes. Clarity in many images was so exceptional that small tracks left by organisms traversing fine-grained carbonate sand were visible. Other images revealed a compelling sense, not yet fully understood, of the microscopic wall structure characteristic of scleractinian corals. Conclusions drawn from classifiable images are that demersal marine animals, where imaged, are oblivious to the equipment and that the technology has strong capabilities beyond mapping habitat. Imagery acquired along predetermined transects that cross a variety of geomorphic features within depth limits will ( 1) facilitate construction of accurate contour maps of habitat and bathymetry without need for ground-truthing, (2) contain a strong geologic component of interpreted real-time processes as they relate to imaged topography and regional geomorphology, and (3) allow cost-effective monitoring of regional- and local-scale changes in an ecosystem by use of existing-image global-positioning system coordinates to re-image areas. Details revealed in the modern setting have taphonomic implications for what is often found in the geologic record.

Habitat Mapping and Classification of the Grand Bay National Estuarine Research Reserve using AISA Hyperspectral Imagery

NASA Astrophysics Data System (ADS)

Rose, K.

2012-12-01

Habitat mapping and classification provides essential information for land use planning and ecosystem research, monitoring and management. At the Grand Bay National Estuarine Research Reserve (GRDNERR), Mississippi, habitat characterization of the Grand Bay watershed will also be used to develop a decision-support tool for the NERR's managers and state and local partners. Grand Bay NERR habitat units were identified using a combination of remotely sensed imagery, aerial photography and elevation data. Airborne Imaging Spectrometer for Applications (AISA) hyperspectral data, acquired 5 and 6 May 2010, was analyzed and classified using ENVI v4.8 and v5.0 software. The AISA system was configured to return 63 bands of digital imagery data with a spectral range of 400 to 970 nm (VNIR), spectral resolution (bandwidth) at 8.76 nm, and 1 m spatial resolution. Minimum Noise Fraction (MNF) and Inverse Minimum Noise Fraction were applied to the data prior to using Spectral Angle Mapper ([SAM] supervised) and ISODATA (unsupervised) classification techniques. The resulting class image was exported to ArcGIS 10.0 and visually inspected and compared with the original imagery as well as auxiliary datasets to assist in the attribution of habitat characteristics to the spectral classes, including: National Agricultural Imagery Program (NAIP) aerial photography, Jackson County, MS, 2010; USFWS National Wetlands Inventory, 2007; an existing GRDNERR habitat map (2004), SAV (2009) and salt panne (2002-2003) GIS produced by GRDNERR; and USACE lidar topo-bathymetry, 2005. A field survey to validate the map's accuracy will take place during the 2012 summer season. ENVI's Random Sample generator was used to generate GIS points for a ground-truth survey. The broad range of coastal estuarine habitats and geomorphological features- many of which are transitional and vulnerable to environmental stressors- that have been identified within the GRDNERR point to the value of the Reserve for continued coastal research.

Preliminary integrated geologic map databases for the United States: Digital data for the reconnaissance bedrock geologic map for the northern Alaska peninsula area, southwest Alaska

USGS Publications Warehouse

,

2006-01-01

he growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Preliminary integrated geologic map databases for the United States: Digital data for the reconnaissance geologic map of the western Aleutian Islands, Alaska

USGS Publications Warehouse

,

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO Exportfiles/ and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Preliminary integrated geologic map databases for the United States: Digital data for the generalized bedrock geologic map, Yukon Flats region, east-central Alaska

USGS Publications Warehouse

Till, Alison B.; Dumoulin, Julie A.; Phillips, Jeffrey D.; Stanley, Richard G.; Crews, Jessie

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Preliminary integrated geologic map databases for the United States: Digital data for the reconnaissance geologic map of the lower Yukon River region, Alaska

USGS Publications Warehouse

,

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Cross-disciplinary Undergraduate Research: A Case Study in Digital Mapping, western Ireland

NASA Astrophysics Data System (ADS)

Whitmeyer, S. J.; de Paor, D. G.; Nicoletti, J.; Rivera, M.; Santangelo, B.; Daniels, J.

2008-12-01

As digital mapping technology becomes ever more advanced, field geologists spend a greater proportion of time learning digital methods relative to analyzing rocks and structures. To explore potential solutions to the time commitment implicit in learning digital field methods, we paired James Madison University (JMU) geology majors (experienced in traditional field techniques) with Worcester Polytechnic Institute (WPI) engineering students (experienced in computer applications) during a four week summer mapping project in Connemara, western Ireland. The project consisted of approximately equal parts digital field mapping (directed by the geology students), and lab-based map assembly, evaluation and formatting for virtual 3D terrains (directed by the engineering students). Students collected geologic data in the field using ruggedized handheld computers (Trimble GeoExplorer® series) with ArcPAD® software. Lab work initially focused on building geologic maps in ArcGIS® from the digital field data and then progressed to developing Google Earth-based visualizations of field data and maps. Challenges included exporting GIS data, such as locations and attributes, to KML tags for viewing in Google Earth, which we accomplished using a Linux bash script written by one of our engineers - a task outside the comfort zone of the average geology major. We also attempted to expand the scope of Google Earth by using DEMs of present-day geologically-induced landforms as representative models for paleo-geographic reconstructions of the western Ireland field area. As our integrated approach to digital field work progressed, we found that our digital field mapping produced data at a faster rate than could be effectively managed during our allotted time for lab work. This likely reflected the more developed methodology for digital field data collection, as compared with our lab-based attempts to develop new methods for 3D visualization of geologic maps. However, this experiment in cross-disciplinary undergraduate research was a big success, with an enthusiastic interchange of expertise between undergraduate geology and engineering students that produced new, cutting-edge methods for visualizing geologic data and maps.

The Avignon Bridge: a 3d Reconstruction Project Integrating Archaeological, Historical and Gemorphological Issues

NASA Astrophysics Data System (ADS)

Berthelot, M.; Nony, N.; Gugi, L.; Bishop, A.; De Luca, L.

2015-02-01

The history and identity of the Avignon's bridge is inseparable from that of the Rhône river. Therefore, in order to share the history and memory of the Rhône, it is essential to get to know this bridge and especially to identify and make visible the traces of its past, its construction, its interaction with the river dynamics, which greatly influenced his life. These are the objectives of the PAVAGE project that focuses on digitally surveying, modelling and re-visiting a heritage site of primary importance with the aim of virtually restoring the link between the two sides which, after the disappearance of the Roman bridge of Arles, constituted for a long time the only connection between Lyon or Vienna and the sea. Therefore, this project has an important geo-historical dimension for which geo-morphological and paleoenvironmental studies were implemented in connection with the latest digital simulation methods exploiting geographic information systems. By integrating knowledge and reflections of archaeologists, historians, geomorphologists, environmentalists, architects, engineers and computer scientists, the result of this project (which involved 5 laboratories during 4 years) is a 3D digital model covering an extension of 50 km2 achieved by integrating satellite imagery, UAV-based acquisitions, terrestrial laser scanning and photogrammetry, etc. Beyond the actions of scientific valorisation concerning the historical and geomorphological dimensions of the project, the results of this work of this interdisciplinary investigation and interpretation of this site are today integrated within a location-based augmented reality application allowing tourists to exploring the virtual reconstruction of the bridge and its environment through tablets inside the portion of territory covered by this project (between Avignon and Villeneuve-lez-Avignon). This paper presents the main aspects of the 3D virtual reconstruction approach.

Preparation and Presentation of Digital Maps in Raster Format

USGS Publications Warehouse

Edwards, K.; Batson, R.M.

1980-01-01

A set of algorithms has been developed at USGS Flagstaff for displaying digital map data in raster format. The set includes: FILLIN, which assigns a specified attribute code to units of a map which have been outlined on a digitizer and converted to raster format; FILBND, which removes the outlines; ZIP, which adds patterns to the map units; and COLOR, which provides a simplified process for creating color separation plates for either photographic or lithographic reproduction. - Authors

Evaluation of using digital gravity field models for zoning map creation

NASA Astrophysics Data System (ADS)

Loginov, Dmitry

2018-05-01

At the present time the digital cartographic models of geophysical fields are taking a special significance into geo-physical mapping. One of the important directions to their application is the creation of zoning maps, which allow taking into account the morphology of geophysical field in the implementation automated choice of contour intervals. The purpose of this work is the comparative evaluation of various digital models in the creation of integrated gravity field zoning map. For comparison were chosen the digital model of gravity field of Russia, created by the analog map with scale of 1 : 2 500 000, and the open global model of gravity field of the Earth - WGM2012. As a result of experimental works the four integrated gravity field zoning maps were obtained with using raw and processed data on each gravity field model. The study demonstrates the possibility of open data use to create integrated zoning maps with the condition to eliminate noise component of model by processing in specialized software systems. In this case, for solving problem of contour intervals automated choice the open digital models aren't inferior to regional models of gravity field, created for individual countries. This fact allows asserting about universality and independence of integrated zoning maps creation regardless of detail of a digital cartographic model of geo-physical fields.

Digital Data for the reconnaissance geologic map for Prince William Sound and the Kenai Peninsula, Alaska

USGS Publications Warehouse

Wilson, Frederic H.; Hults, Chad P.; Labay, Keith A.; Shew, Nora B.

2007-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. The files named __geol contain geologic polygons and line (contact) attributes; files named __fold contain fold axes; files named __lin contain lineaments; and files named __dike contain dikes as lines. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Analysis of Tsunamigenic Coastal Rock Slope Failures Triggered by the 2007 Earthquake in the Chilean Fjordland

NASA Astrophysics Data System (ADS)

Sepulveda, S. A.; Serey, A.; Hermanns, R. L.; Redfield, T. F.; Oppikofer, T.; Duhart, P.

2011-12-01

The fjordland of the Chilean Patagonia is subject to active tectonics, with large magnitude subduction earthquakes, such as the M 9.5 1960 earthquake, and shallow crustal earthquakes along the regional Liquiñe-Ofqui Fault Zone (LOFZ). One of the latter (M 6.2) struck the Aysen Fjord region (45.5 S) on the 21st of April 2007, triggering dozens of landslides in the epicentral area along the fjord coast and surroundings. The largest rock slides and rock avalanches induced a local tsunami that together with debris flows caused ten fatalities and severely damaged several salmon farms, the most important economic activity of the area. Multi-scale studies of the landslides triggered during the Aysen earthquake have been carried out, including landslide mapping and classification, slope stability back-analyses and structural and geomorphological mapping of the largest failures from field surveys and high-resolution digital surface models created from terrestrial laser scanning. The failures included rock slides, rock avalanches, rock-soil slides, soil slides and debris flows. The largest rock avalanche had a volume of over 20 million cubic metres. The landslides affected steep slopes of intrusive rocks of the North Patagonian batholith covered by a thin layer of volcanic soils, which supports a high forest. The results of geotechnical analyses suggest a site effect due to topographic amplification on the generation of the landslides, with peak ground accelerations that may have reached between about 1.0 and 2.0 g for rock avalanches and between 0.6 and 1.0 g for shallow rock-soil slides, depending on the amount of assumed vertical acceleration and the applied method (limit equilibrium and Newmark). Attenuation relationships for shallow crustal seismicity indicate accelerations below 0.5 g for earthquakes of a similar magnitude and epicentral distances. Detailed field structural analyses of the largest rock avalanche in Punta Cola indicate a key role in the failure mechanics of brittle faults and jointing related to the LOFZ. The basal failure plane closely followed an older (epidote chlorite facies) thrust fault. Later fracture patterns suggest the thrust relaxed under gravitational stress following rock column uplift. Failure probably utilized a combination of these structures. Digital geomorphic models allowed establishing a sequence of events during failure which together make up the complex rock avalanche deposit. The volume of each individual slide could be more accurately determined. These and ongoing studies will allow a unique characterization of earthquake-induced slope failures in fjord coastal environments, providing new tools for landslide, seismic and tsunami hazard assessment in Patagonia and similar geomorphological settings around the world. This work was funded by Fondecyt project 11070107, the International Center for Geohazards, the Millenium Nucleus 'International Earthquake Research Center Montessus de Ballore', FNDR-Project 'Geological-Mining Environmental Research in Aysen' of the Chilean Government and the Andean Geothermal Center of Excellence.

Mapping of the Culann-Tohil Region of Io

NASA Technical Reports Server (NTRS)

Turtle, E. P.; Keszthelyi, L. P.; Jaeger, W. L.; Radebaugh, J.; Milazzo, M. P.; McEwen, A. S.; Moore, J. M.; Schenk, P. M.; Lopes, R. M. C.

2003-01-01

The Galileo spacecraft completed its observations of Jupiter's volcanic moon Io in October 2001 with the orbit I32 flyby, during which new local (13-55 m/pixel) and regional (130-400 m/pixel) resolution images and spectroscopic data were returned of the antijovian hemisphere. We have combined a I32 regional mosaic (330 m/pixel) with lower-resolution C21 color data (1.4 km/pixel, Figure 1) and produced a geomorphologic map of the Culann-Tohil area of this hemisphere. Here we present the geologic features, map units, and structures in this region, and give preliminary conclusions about geologic activity for comparison with other regions to better understand Io's geologic evolution.

Refining Landsat classification results using digital terrain data

USGS Publications Warehouse

Miller, Wayne A.; Shasby, Mark

1982-01-01

 Scientists at the U.S. Geological Survey's Earth Resources Observation systems (EROS) Data Center have recently completed two land-cover mapping projects in which digital terrain data were used to refine Landsat classification results. Digital ter rain data were incorporated into the Landsat classification process using two different procedures that required developing decision criteria either subjectively or quantitatively. The subjective procedure was used in a vegetation mapping project in Arizona, and the quantitative procedure was used in a forest-fuels mapping project in Montana. By incorporating digital terrain data into the Landsat classification process, more spatially accurate landcover maps were produced for both projects.

Lateglacial geomorphology in the Tweedsmuir Hills, Scotland - Implications for retreat patterns, glacier reconstruction and chronology.

NASA Astrophysics Data System (ADS)

Pearce, D.; Rea, B.; McDougall, D.

2012-04-01

The Tweedsmuir Hills, Southern Uplands, Scotland, contain excellent assemblages of glacial landforms, including hummocky moraine, classically associated with a Lateglacial deglaciation (c. 14.7 - 11.7 cal. ka BP) in the UK. Although initially documented in 1855, a detailed systematic geomorphological investigation has never been undertaken in the region, meaning reconstructions are patchy, outdated and lacking chronological control. This has resulted in conflicting styles of glaciation being inferred, with both plateau icefield and valley glaciers reconstructed in the Tweedsmuir Hills. Importantly, comprehensive numerical modelling experiments for the period, c. 38 -10.4 ka BP, predict a significant body of ice for the Tweedsmuir Hills at the onset and throughout the Younger Dryas (c. 12.9 - 11.7 cal. ka. BP). Field data, which at present, are missing means that the numerical modelling remains untested. Given the emerging evidence that ice-masses survived, during or throughout the Lateglacial in a number of regions in Scotland, the glacial geomorphology and reconstructions for this area will provide a key input of palaeo-glacier data for subsequent investigation of wider patterns of Lateglacial ice-mass distribution and climate gradients across the UK and NW Europe. Geomorphological mapping followed a morphostratigraphic approach using a combination of aerial photos, NEXTMapTM and mapping in the field using a ruggedized tablet PC, with built in GPS and ArcGIS 9.3. The glacial landforms indicate two separate landsystems. The first is characterised by elongate subglacial bedforms overriding the topography, trending SW to NE, suggested to be attributable to the Devensian glaciation. The second landsystem is characterised by closely spaced sharp crested moraines, oblique to the valley axis and confined by the topography, meltwater channels and single terrace systems, which are likely to have formed in a subsequent period of renewed glaciation i.e. Lateglacial. The Lateglacial landform assemblage indicates more extensive glaciation than previously envisaged, with both a transection ice-mass and icefield coexisting, reflecting different topographic controls. Interestingly, a geomorphic pattern is observable in more than one valley, which is interpreted as a synchronous recession of the outlet glaciers and a rapid deglaciation towards the summits. Whilst two landsystems have been mapped the second poses interesting problems regarding extent and timing of glaciation. The Loch Skene site has been traditionally associated with a small valley glacier. However, it appears to feed ice into a lower valley which exhibits a landform assemblage typical of Lateglacial deglaciation in Scotland. It is tentatively proposed that the Loch Skene glacier represents a retreat phase prior to complete deglaciation rather than the Younger Dryas maximum.

Preliminary geologic map of the Santa Barbara coastal plain area, Santa Barbara County, California

USGS Publications Warehouse

Minor, Scott A.; Kellogg, Karl S.; Stanley, Richard G.; Stone, Paul; Powell, Charles L.; Gurrola, Larry D.; Selting, Amy J.; Brandt, Theodore R.

2002-01-01

This report presents a new geologic digital map of the Santa Barbara coastal plain area at a compilation scale of 1:24,000 (one inch on the map = 2,000 feet on the ground) and with a horizontal positional accuracy of at least 20 m. This preliminary map depicts the distribution of bedrock units and surficial deposits and associated deformation underlying and adjacent to the coastal plain within the contiguous Santa Barbara and Goleta 7.5' quadrangles. A planned second version will extend the mapping westward into the adjoining Dos Pueblos Canyon quadrangle and eastward into the Carpinteria quadrangle. The mapping presented here results from the collaborative efforts of geologists with the U.S. Geological Survey Southern California Areal Mapping Project (SCAMP) (Minor, Kellogg, Stanley, Stone, and Powell) and the tectonic geomorphology research group at the University of California at Santa Barbara (Gurrola and Selting). C.L. Powell, II, performed all new fossil identifications and interpretations reported herein. T.R. Brandt designed and edited the GIS database,performed GIS database integration and created the digital cartography for the map layout. The Santa Barbara coastal plain is located in the western Transverse Ranges physiographic province along a west-trending segment of the southern California coastline about 100 km (62 mi) northwest of Los Angeles. The coastal plain region, which extends from the Santa Ynez Mountains on the north to the Santa Barbara Channel on the south, is underlain by numerous active and potentially active folds and partly buried thrust faults of the Santa Barbara fold and fault belt. Strong earthquakes that occurred in the region in 1925 (6.8 magnitude) and 1978 (5.1 magnitude) are evidence that such structures pose a significant earthquake hazard to the approximately 200,000 people living within the major coastal population centers of Santa Barbara and Goleta. Also, young landslide deposits along the steep lower flank of the Santa Ynez Mountains indicate the potential for continued slope failures and mass movements that may threaten urbanized parts of the coastal plain. Deformed sedimentary rocks in the subsurface of the coastal plain and the adjacent Santa Barbara Channel contain deposits of oil and gas, some of which are currently being extracted. Shallow, localized sedimentary aquifers underlying the coastal plain provide limited amounts of water for the urban areas, but the quality of some of this groundwater is compromised by coastal salt-water contamination. The present map compilation provides a set of uniform geologic digital coverages that can be used for analysis and prediction of these and other geologic hazards and resources in the coastal plain region. In the map area the oldest stratigraphic units consist of resistant Eocene to Oligocene marine and terrestrial sedimentary rocks that form a mostly southward-dipping and laterally continuous sequence along the south flank of the Santa Ynez Mountains. Less resistant, but more variably deformed, Miocene, Pliocene, and Pleistocene marine sedimentary rocks and deposits are exposed in the lower Santa Ynez foothills and in the coastal hills and sea cliffs farther south. Pleistocene and Holocene surficial alluvial, colluvial, estuarine, and marine-terrace deposits directly underlie much of the low-lying coastal plain area, and similar-aged alluvial and landslide deposits locally mantle the lower flanks of the Santa Ynez Mountains. Structurally, the Santa Barbara coastal plain area is dominated by the Santa Barbara fold and fault belt, an east-west-trending zone of Quaternary, partly active folds and blind and exposed reverse and thrust faults. The dominant trend of individual structures within the belt is west-northwest -- slightly oblique to the overall trend of the fold and fault belt. A conspicuous exception, however, is the More Ranch fault system, which strikes east-northeast across the fold and f

Digital line graphs from 1:24,000-scale maps

USGS Publications Warehouse

,

1990-01-01

The Earth Science Information Centers (ESIC) distribute digital cartographic/geographic data files produced by the U.S. Geological Survey (USGS) as part of the National Mapping Program. Digital cartographic data flles are grouped into four basic types. The first of these, called a Digital Line . Graph (DLG), is line map information in digital form. These data files include information on planimetric base categories, such as transportation, hydrography, and boundaries. The second type, called a Digital Elevation Model (DEM), consists of a sampled array of elevations for a number of ground positions that are usually at regularly spaced intervals. The third type is Land Use and Land Cover digital data, which provides information on nine major classes of land use such as urban, agricultural, or forest as wen as associated map data such as political units and Federal land ownership. The fourth type, the Geographic Names Information System, provides primary information for all known places, features, and areas in the United States identified by a proper name.

Digital line graphs from 1:100,000-scale maps

USGS Publications Warehouse

,

1989-01-01

The National Cartographic Information Center (NCIC) distributes digital cartographic/geographic data files produced by the U.S. Geological Survey (USGS) as part of the National Mapping Program. Digital cartographic data files may be grouped into four basic types. The first of these, called a Digital Line Graph (DLG), is line map information in digital form. These data files include information on planimetric base categories, such as transportation, hydrography, and boundaries. The second form, called a Digital Elevation Model (OEM), consists of a sampled array of elevations for ground positions that are usually, but not always, at regularly spaced intervals. The third type is Land Use and Land Cover digital data, which provides information on nine major classes of land use such as urban, agricultural, or forest as well as associated map data such as political units and Federal land ownership. The fourth type, the Geographic Names Information System, provides primary information for known places, features, and areas in the United States identified by a proper name.

Geomorphology of comet 67P/Churyumov–Gerasimenko

USGS Publications Warehouse

Birch, Samuel P. D.; Tang, Y.; Hayes, A. G.; Kirk, Randolph L.; Bodewitz, D.; Campins, H.; Fernandez, Y.; de Freitas Bart, R.; Kutsop, N. W.; Sierks, H.; Soderblom, J. M.; Squyres, S. W.; Vincent, J.-B.

2017-01-01

We present a global geomorphological map of comet 67P/Churyumov–Gerasimenko (67P/C-G) using data acquired by the Rosetta Orbiter’s OSIRIS Narrow Angle Camera. The images used in our study were acquired between 2014 August and 2015 May, before 67P/C-G passed through perihelion. Imagery of the Southern hemisphere was included in our study, allowing us to compare the contrasting hemispheres of 67P/C-G in a single study. Our work also puts into greater context the morphologies studied in previous works, and also the morphologies observed on previously visited cometary nuclei. Relative to other nuclei, 67P/C-G appears most similar to 81P/Wild 2, with a topographically heterogeneous surface dominated by smooth-floored pits. Our mapping describes the landscapes of 67P/C-G when they were first observed by Rosetta, and our map can be used to detect changes in surface morphologies after its perihelion passage. Our mapping reveals strong latitudinal dependences for emplaced units and a highly heterogeneous surface. Layered bedrock units that represent the exposed nucleus of 67P/C-G are dominant at southern latitudes, while topographically smooth, dust covered regions dominate the Northern hemisphere. Equatorial latitudes are dominated by smooth terrain units that show evidence for flow structures. We observe no obvious differences between the comet’s two lobes, with the only longitudinal variations being the Imhotep and Hatmehit basins. These correlations suggest a strong seasonal forcing on the surface evolution of 67P/C-G, where materials are transported from the Southern hemisphere to Northern hemisphere basins over multiple orbital time-scales.

Digital data for the geology of the Southern Brooks Range, Alaska

USGS Publications Warehouse

Till, Alison B.; Dumoulin, Julie A.; Harris, Anita G.; Moore, Thomas E.; Bleick, Heather A.; Siwiec, Benjamin; Labay, Keith A.; Wilson, Frederic H.; Shew, Nora B.

2008-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. The files named __geol contain geologic polygons and line (contact) attributes; files named __fold contain fold axes; files named __lin contain lineaments; and files named __dike contain dikes as lines. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

An ocean gazetteer for education and research

NASA Astrophysics Data System (ADS)

Delaney, R.; Staudigel, D.; Staudigel, H.

2003-04-01

Global travel, economy, and news coverage often challenge the student's and teacher's knowledge of the geography of the seas. The International Hydrographic Organization (IHO) has published a description of all the major seas making up earth's oceans, but there is currently no electronic tool that identifies them on a digital map. During an internship at Scripps Institution of Oceanography, we transferred the printed visual description of the seas from IHO publication 23 into a digital format. This digital map was turned into a (Flash) web application that allows a user to identify any of the IHO seas on a world map, simply by moving the computer cursor over it. In our presentation, we will describe the path taken to produce this web application and the learning process involved in this path during our internship at Scripps. The main steps in this process included the digitization of the official IHO maps, the transfer of this information onto a modern digital map by Smith and Sandwell. Adjustments were necessary due to the fact that many of the landmasses were placed incorrectly on a lat/long grid, off by as much as 100km. Boundaries between seas were often misrepresented by the IHO as straight lines on a Mercator projection. Once the digitization of the seas was completed we used the 2d animation environment Flash and we produced an interactive map environment that allows any teacher or student of ocean geography to identify an ocean by name and location. Aside from learning about the geography of the oceans, we were introduced to the use of digitizers, we learned to make maps using Generic Mapping Tools (GMT) and digital global bathymetry data sets, and we learned about map projections. We studied Flash to produce an interactive map of the oceans that displays bathymetry and topography, highlighting any particular sea the cursor moves across. The name of the selected sea in our Flash application appears in a textbox on the bottom of the map. The result of this project can be found at http://earthref.org/PACER/beta/IH023seas.

Geomorphological evolution of a fluvial channel after primary lahar deposition: Huiloac Gorge, Popocatépetl volcano (Mexico)

NASA Astrophysics Data System (ADS)

Tanarro, L. M.; Andrés, N.; Zamorano, J. J.; Palacios, D.; Renschler, C. S.

2010-10-01

Popocatépetl volcano (19°02' N, 98°62' W, 5424 m) began its most recent period of volcanic activity in December 1994. The interaction of volcanic and glacier activity triggered the formation of lahars through the Huiloac Gorge, located on the northern flank of the volcano, causing significant morphological changes in the channel. The most powerful lahars occurred in April 1995, July 1997 and January 2001, and were followed by secondary lahars that formed during the post-eruptive period. This study interprets the geomorphological evolution of the Huiloac Gorge after the January 2001 lahar. Variations in channel morphology at a 520 m-long research site located mid-way down the gorge were recorded over a 4 year period from February 2002 to March 2005, and depicted in five geomorphological maps (scale 1:200) for 14 February and 15 October 2002, 27 September 2003, 9 February 2004, and 16 March 2006. A GIS was used to calculate the surface area for the landforms identified for each map and detected changes and erosion-deposition processes of the landforms using the overlay function for different dates. Findings reveal that secondary lahars and others types of flows, like sediment-laden or muddy streamflows caused by precipitation, rapidly modified the gorge channel following the January 2001 non-eruptive lahar, a period associated with volcanic inactivity and the disappearance of the glacier once located at the headwall of the gorge. Field observations also confirmed that secondary flows altered the dynamics and geomorphological development of the channel. These flows incised and destroyed the formations generated by the primary lahars (1997 and 2001), causing a widening of the channel that continues today. After February 2004, a rain-triggered lahar and other flows infilled the channel with materials transported by these flows. The deposits on the lateral edges of the channel form terraces. A recent lull in lahar activity contrasts with the increasing instability of the edges of the channel and the continuous edification and destruction of recent lahar terraces.

Geomorphic evidence of Quaternary tectonics within an underlap fault zone of southern Apennines, Italy

NASA Astrophysics Data System (ADS)

Giano, Salvatore Ivo; Pescatore, Eva; Agosta, Fabrizio; Prosser, Giacomo

2018-02-01

A composite seismic source, the Irpinia - Agri Valley Fault zone, located in the axial sector of the fold-and-thrust belt of southern Apennines, Italy, is investigated. This composite source is made up of a series of nearly parallel, NW-striking normal fault segments which caused many historical earthquakes. Two of these fault segments, known as the San Gregorio Magno and Pergola-Melandro, and the fault-related mountain fronts, form a wedge-shaped, right-stepping, underlap fault zone. This work is aimed at documenting tectonic geomorphology and geology of this underlap fault zone. The goal is to decipher the evidence of surface topographic interaction between two bounding fault segments and their related mountain fronts. In particular, computation of geomorphic indices such as mountain front sinuosity (Smf), water divide sinuosity (Swd), asymmetry factor (AF), drainage basin elongation (Bs), relief ratio (Rh), Hypsometry (HI), normalized steepness (Ksn), and concavity (θ) is integrated with geomorphological analysis, the geological mapping, and structural analysis in order to assess the recent activity of the fault scarp sets recognized within the underlap zone. Results are consistent with the NW-striking faults as those showing the most recent tectonic activity, as also suggested by presence of related slope deposits younger than 38 ka. The results of this work therefore show how the integration of a multidisciplinary approach that combines geomorphology, morphometry, and structural analyses may be key to solving tectonic geomorphology issues in a complex, fold-and-thrust belt configuration.

Spatial Digital Database for the Geology of the San Pedro River Basin in Cochise, Gila, Graham, Pima, and Pinal Counties, Arizona

USGS Publications Warehouse

Bolm, Karen S.

2002-01-01

The map area is located in southeastern Arizona. This report describes the map units, the methods used to convert the geologic map data into a digital format, and the ArcInfo GIS file structures and relationships; and it explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet. See figures 2 and 3 for page-size versions of the map compilation.

Toward digital geologic map standards: a progress report

USGS Publications Warehouse

Ulrech, George E.; Reynolds, Mitchell W.; Taylor, Richard B.

1992-01-01

Establishing modern scientific and technical standards for geologic maps and their derivative map products is vital to both producers and users of such maps as we move into an age of digital cartography. Application of earth-science data in complex geographic information systems, acceleration of geologic map production, and reduction of population costs require that national standards be developed for digital geologic cartography and computer analysis. Since December 1988, under commission of the Chief Geologic of the U.S. Geological Survey and the mandate of the National Geologic Mapping Program (with added representation from the Association of American State Geologists), a committee has been designing a comprehensive set of scientific map standards. Three primary issues were: (1) selecting scientific symbology and its digital representation; (2) creating an appropriate digital coding system that characterizes geologic features with respect to their physical properties, stratigraphic and structural relations, spatial orientation, and interpreted mode of origin; and (3) developing mechanisms for reporting levels of certainty for descriptive as well as measured properties. Approximately 650 symbols for geoscience maps, including present usage of the U.S Geological Survey, state geological surveys, industry, and academia have been identified and tentatively adopted. A proposed coding system comprises four-character groupings of major and minor codes that can identify all attributes of a geologic feature. Such a coding system allows unique identification of as many as 105 geologic names and values on a given map. The new standard will track closely the latest developments of the Proposed Standard for Digital Cartographic Data soon to be submitted to the National Institute of Standards and Technology by the Federal Interagency Coordinating Committee on Digital Cartography. This standard will adhere generally to the accepted definitions and specifications for spatial data transfer. It will require separate specifications of digital cartographic quality relating to positional accuracy and ranges of measured and interpreted values such as geologic age and rock composition. Provisional digital geologic map standards will be published for trial implementation. After approximately two years, when comments on the proposed standards have been solicited and modifications made, formal adoption of the standards will be recommended. Widespread acceptance of the new standards will depend on their applicability to the broadest range of earth-science map products and their adaptability to changing cartographic technology.

Mitigating the effects of landscape development on streams in urbanizing watersheds

USGS Publications Warehouse

Hogan, Dianna M.; Jarnagin, S. Taylor; Loperfido, John V.; Van Ness, Keith

2013-01-01

This collaborative study examined urbanization and impacts on area streams while using the best available sediment and erosion control (S&EC) practices in developing watersheds in Maryland, United States. During conversion of the agricultural and forested watersheds to urban land use, land surface topography was graded and vegetation was removed creating a high potential for sediment generation and release during storm events. The currently best available S&EC facilities were used during the development process to mitigate storm runoff water quality, quantity, and timing before entering area streams. Detailed Geographic Information System (GIS) maps were created to visualize changing land use and S&EC practices, five temporal collections of LiDAR (light detection and ranging) imagery were used to map the changing landscape topography, and streamflow, physical geomorphology, and habitat data were used to assess the ability of the S&EC facilities to protect receiving streams during development. Despite the use of the best available S&EC facilities, receiving streams experienced altered flow, geomorphology, and decreased biotic community health. These impacts on small streams during watershed development affect sediment and nutrient loads to larger downstream aquatic ecosystems such as the Chesapeake Bay.

Geomorphic change detection in proglacial areas using repetitive unmanned aerial vehicle (UAV) surveys

NASA Astrophysics Data System (ADS)

Ewertowski, Marek; Evans, David; Roberts, David; Tomczyk, Aleksandra; Ewertowski, Wojciech

2017-04-01

Glacial forelands exposed due to the glacier recession are one of the most dynamically transformed landscapes in Polar and mountainous areas. These areas are supposed to be intensively changed by various geomorphological processes related to the glacial retreat and meltwater activity, as well as paraglacial adjustment of topography. This study deals with landscape transformation in an annual time-scale in the foreland of Hørbyebreen and Rieperbreen (Svalbard) and Fjallsjökull and Kviárjökull (Iceland) to assess landscape changes in 2014-2016 period. The main aim of this study is to map and quantify landforms development in detailed spatial scale to provide an insight into geomorphological processes which occurred shortly after the retreat of the ice margin. Low-altitude aerial photographs were taken using small quadcopter equipped with 12 MP camera. Images were acquired at an elevation between 40 and 60 m above the ground level. The images were subsequently processed using structure-from-motion approach to produce orthomosaics ( 3 cm cell size) and digital elevation models (DEMs) with 5-10 cm cell size. Subtracting DEMs from subsequent time periods created DEMs of Differences — which enabled us to calculate the amount of material loss or deposition. Accuracy of the orthophotos and DEMs was improved using ground control points measured with dGPS. Over the 2014-2016 period repetitive UAV-based surveys revealed and quantify changes in landscape including: (1) glacier thinning; (2) ice-cored moraines degradation; (3) development of terminoglacial and supraglacial lakes; (4) debris flow activity. Short-time dynamics of different components showed very high variability over time and space illustrating relative importance of ice backwasting and downwasting as well as glacifluvial processes for studied forelands The research was founded by Polish National Science Centre (project granted by decision number DEC-2011/01/D/ST10/06494).

PaleoGeo: a Web based GIS database for paleoenvironmental studies

NASA Astrophysics Data System (ADS)

Song, Wonsuh; Kondo, Yasuhisa; Oguchi, Takashi

2014-05-01

Paleoenvironmental studies cover various fields such as paleohydrology, geomorphology, paleooceanology, paleobiology, paleoclimatology, and chronology. It is difficult for an individual researcher to collect and compile enormous data regarding these fields. We have been compiling portal data and presenting them using a web-based geographical information system (Web-GIS) called PaleoGeo for the multidisciplinary project 'Replacement of Neanderthals by Modern Humans'. The aim of the project is to reconstruct the distribution of Neanderthals and modern humans in time and space in relation to past climate change. We have been collecting information from almost three thousand articles of 13 journals regarding paleoenvironmental research (i.e., Boreas, Catena, Climatic Change, Earth Surface Processes and Landforms, Geomorphology, Journal of Quaternary Science, Palaeogeography, Palaeoclimatology, and Palaeoecology, Quaternary International, Quaternary Research, Quaternary Science Reviews, The Holocene, and The Journal of Geology). The topics of the articles were classified into six themes (paleohydrology, earth surface processes and materials, paleooceanology, paleobiology, palaeoclimatology, and chronology) and 19 subthemes (hydrology, flood, fluvial, glacier, fluvial/glacier, sedimentology, soil, slope process, periglacial, peat land, eolian, sea-level, biology, vegetation, zoology, vegetation/zoology, archaeology, climate, atmosphere, and chronology). The collected data consist of the journal name, information about each paper (authors, title, volume, year, and page numbers), site location (country name, longitude, and latitude), theme, subtheme, keywords, DOI (Digital Object Identifier), and period (era). Location data are indispensable for paleoenvironmental studies. The PaleoGeo shows information with a map, which is an advantage of this database system. However, the number of the paleoenvironmental studies is growing rapidly and we have to effectively cover them as many as possible. We plan to simplify the input data (latitude, longitude, title and DOI only) to include more publications. So far information about >7500 sites has been collected and the number is increasing. The collected data are accessible via the internet (http://neangis.csis.u-tokyo.ac.jp/paleogeo/).

Quantitative paleotopography and paleogeography around the Gibraltar Arc (South Spain) during the Messinian Salinity Crisis

NASA Astrophysics Data System (ADS)

Elez, Javier; Silva, Pablo G.; Huerta, Pedro; Perucha, M. Ángeles; Civis, Jorge; Roquero, Elvira; Rodríguez-Pascua, Miguel A.; Bardají, Teresa; Giner-Robles, Jorge L.; Martínez-Graña, Antonio

2016-12-01

The Malaga basin contains an important geological record documenting the complex paleogeographic evolution of the Gibraltar Arc before, during and after the closure and desiccation of the Mediterranean Sea triggered by the "Messinian Salinity crisis" (MSC). Proxy paleo-elevation data, estimated from the stratigraphic and geomorphological records, allow the building of quantitative paleogeoid, paleotopographic and paleogeographic models for the three main paleogeographic stages: pre-MSC (Tortonian-early Messinian), syn-MSC (late Messinian) and post-MSC (early Pliocene). The methodological workflow combines classical contouring procedures used in geology and isobase map models from geomorphometric analyses and proxy data overprinted on present Digital Terrain Models. The resulting terrain quantitative models have been arranged, managed and computed in a GIS environment. The computed terrain models enable the exploration of past landscapes usually beyond the reach of classical geomorphological analyses and strongly improve the paleogeographic and paleotopographic knowledge of the study area. The resulting models suggest the occurrence of a set of uplifted littoral erosive and paleokarstic landforms that evolved during pre-MSC times. These uplifted landform assemblages can explain the origin of key elements of the present landscape, such as the Torcal de Antequera and the large amount of mogote-like relict hills present in the zone, in terms of ancient uplifted tropical islands. The most prominent landform is the extensive erosional platform dominating the Betic frontal zone that represents the relic Atlantic wave cut platform elaborated during late-Tortonian to early Messinian times. The amount of uplift derived from paleogeoid models suggests that the area rose by about 340 m during the MSC. This points to isostatic uplift triggered by differential erosional unloading (towards the Mediterranean) as the main factor controlling landscape evolution in the area during and after the MSC. Former littoral landscapes in the old emergent axis of the Gibraltar Arc were uplifted to form the main water-divide of the present Betic Cordillera in the zone.

SwathProfiler and NProfiler: Two new ArcGIS Add-ins for the automatic extraction of swath and normalized river profiles

NASA Astrophysics Data System (ADS)

Pérez-Peña, J. V.; Al-Awabdeh, M.; Azañón, J. M.; Galve, J. P.; Booth-Rea, G.; Notti, D.

2017-07-01

The present-day great availability of high-resolution Digital Elevation Models has improved tectonic geomorphology analyses in their methodological aspects and geological meaning. Analyses based on topographic profiles are valuable to explore the short and long-term landscape response to tectonic activity and climate changes. Swath and river longitudinal profiles are two of the most used analysis to explore the long and short-term landscape responses. Most of these morphometric analyses are conducted in GIS software, which have become standard tools for analyzing drainage network metrics. In this work we present two ArcGIS Add-Ins to automatically delineate swath and normalized river profiles. Both tools are programmed in Visual Basic . NET and use ArcObjects library-architecture to access directly to vector and raster data. The SwathProfiler Add-In allows analyzing the topography within a swath or band by representing maximum-minimum-mean elevations, first and third quartile, local relief and hypsometry. We have defined a new transverse hypsometric integral index (THi) that analyzes hypsometry along the swath and offer valuable information in these kind of graphics. The NProfiler Add-In allows representing longitudinal normalized river profiles and their related morphometric indexes as normalized concavity (CT), maximum concavity (Cmax) and length of maximum concavity (Lmax). Both tools facilitate the spatial analysis of topography and drainage networks directly in a GIS environment as ArcMap and provide graphical outputs. To illustrate how these tools work, we analyzed two study areas, the Sierra Alhamilla mountain range (Betic Cordillera, SE Spain) and the Eastern margin of the Dead Sea (Jordan). The first study area has been recently studied from a morphotectonic perspective and these new tools can show an added value to the previous studies. The second study area has not been analyzed by quantitative tectonic geomorphology and the results suggest a landscape in transient state due to a continuous base-level fall produced by the formation of the Dead Sea basin.

Tsunami Rapid Assessment Using High Resolution Images and Field Surveys: the 2010 , Central Chile, and the 2011, Tohoku Tsunamis

NASA Astrophysics Data System (ADS)

Ramirez-Herrera, M.; Navarrete-Pacheco, J.; Lagos, M.; Arcas, D.

2013-12-01

Recent extreme tsunamis have shown their major socioeconomic impact and imprint in the coastal landscape. Extensive destruction, erosion, sediment transport and deposition resculpted coastal landscape within few minutes along hundreds of kilometers of the Central Chile, in 2010, and the Northeast coast of Japan, in 2011. In the central coast of Chile, we performed a post-tsunami survey a week after the tsunami due to access restrictions. Our observations focus on the inundation and geomorphic effects of the 2010 tsunami and included an air reconnaissance flight, analysis of pre- and post-event low fly air-photographs and Google Earth satellite images, together with ground reconnaissance and mapping in the field, including topographic transects, during a period of 13 days. Eyewitness accounts enabled us to confirm our observations on effects produced by the tsunami along ~ 500km along the coastline landscape in central Chile For the Tohoku case study, we assessed in a day tsunami inundation distances and runup heights using satellite data (very high resolution satellite images from the GeoEye1 satellite and from the DigitalGlobe worldview through the Google crisis response project, SRTM and ASTER GDEM) of the Tohoku region, Northeast Japan. Field survey data by Japanese, other international scientists and us validated our results. The rapid assessment of damage using high-resolution images has proven to be an excellent tool neccessary for effcient postsunami surveys as well as for rapid assessment of areas with access restrictions. All countries, in particular those with less access to technology and infrastructure, can benefit from the use of freely available satellite imagery and DEMs for an initial, pre-field survey, rapid estimate of inundated areas, distances and runup, tsunami effects in the coastal geomorphology and for assisting in hazard management and mitigation after a natural disaster. These data provide unprecedented opportunities for rapid assessment and to describe both damage and how tsunamis impacted the coastal geomorphology .

Digitizing zone maps, using modified LARSYS program. [computer graphics and computer techniques for mapping

NASA Technical Reports Server (NTRS)

Giddings, L.; Boston, S.

1976-01-01

A method for digitizing zone maps is presented, starting with colored images and producing a final one-channel digitized tape. This method automates the work previously done interactively on the Image-100 and Data Analysis System computers of the Johnson Space Center (JSC) Earth Observations Division (EOD). A color-coded map was digitized through color filters on a scanner to form a digital tape in LARSYS-2 or JSC Universal format. The taped image was classified by the EOD LARSYS program on the basis of training fields included in the image. Numerical values were assigned to all pixels in a given class, and the resulting coded zone map was written on a LARSYS or Universal tape. A unique spatial filter option permitted zones to be made homogeneous and edges of zones to be abrupt transitions from one zone to the next. A zoom option allowed the output image to have arbitrary dimensions in terms of number of lines and number of samples on a line. Printouts of the computer program are given and the images that were digitized are shown.

Mapping broom snakeweed through image analysis of color-infrared photography and digital imagery.

PubMed

Everitt, J H; Yang, C

2007-11-01

A study was conducted on a south Texas rangeland area to evaluate aerial color-infrared (CIR) photography and CIR digital imagery combined with unsupervised image analysis techniques to map broom snakeweed [Gutierrezia sarothrae (Pursh.) Britt. and Rusby]. Accuracy assessments performed on computer-classified maps of photographic images from two sites had mean producer's and user's accuracies for broom snakeweed of 98.3 and 88.3%, respectively; whereas, accuracy assessments performed on classified maps from digital images of the same two sites had mean producer's and user's accuracies for broom snakeweed of 98.3 and 92.8%, respectively. These results indicate that CIR photography and CIR digital imagery combined with image analysis techniques can be used successfully to map broom snakeweed infestations on south Texas rangelands.

Virtual Field Reconnaissance to enable multi-site collaboration in geoscience fieldwork in Chile.

NASA Astrophysics Data System (ADS)

Hughes, Leanne; Bateson, Luke; Ford, Jonathan; Napier, Bruce; Creixell, Christian; Contreras, Juan-Pablo; Vallette, Jane

2017-04-01

The unique challenges of geological mapping in remote terrains can make cross-organisation collaboration challenging. Cooperation between the British and Chilean Geological Surveys and the Chilean national mining company used the BGS digital Mapping Workflow and virtual field reconnaissance software (GeoVisionary) to undertake geological mapping in a complex area of Andean Geology. The international team undertook a pre-field evaluation using GeoVisionary to integrate massive volumes of data and interpret high resolution satellite imagery, terrain models and existing geological information to capture, manipulate and understand geological features and re-interpret existing maps. This digital interpretation was then taken into the field and verified using the BGS digital data capture system (SIGMA.mobile). This allowed the production of final geological interpretation and creation of a geological map. This presentation describes the digital mapping workflow used in Chile and highlights the key advantages of increased efficiency and communication to colleagues, stakeholders and funding bodies.

Binational digital soils map of the Ambos Nogales watershed, southern Arizona and northern Sonora, Mexico

USGS Publications Warehouse

Norman, Laura

2004-01-01

We have prepared a digital map of soil parameters for the international Ambos Nogales watershed to use as input for selected soils-erosion models. The Ambos Nogales watershed in southern Arizona and northern Sonora, Mexico, contains the Nogales wash, a tributary of the Upper Santa Cruz River. The watershed covers an area of 235 km2, just under half of which is in Mexico. Preliminary investigations of potential erosion revealed a discrepancy in soils data and mapping across the United States-Mexican border due to issues including different mapping resolutions, incompatible formatting, and varying nomenclature and classification systems. To prepare a digital soils map appropriate for input to a soils-erosion model, the historical analog soils maps for Nogales, Ariz., were scanned and merged with the larger-scale digital soils data available for Nogales, Sonora, Mexico using a geographic information system.

The Spectral Nature of Titan's Major Geomorphological Units: Constraints on Surface Composition

NASA Astrophysics Data System (ADS)

Solomonidou, A.; Coustenis, A.; Lopes, R. M. C.; Malaska, M. J.; Rodriguez, S.; Drossart, P.; Elachi, C.; Schmitt, B.; Philippe, S.; Janssen, M.; Hirtzig, M.; Wall, S.; Sotin, C.; Lawrence, K.; Altobelli, N.; Bratsolis, E.; Radebaugh, J.; Stephan, K.; Brown, R. H.; Le Mouélic, S.; Le Gall, A.; Villanueva, E. V.; Brossier, J. F.; Bloom, A. A.; Witasse, O.; Matsoukas, C.; Schoenfeld, A.

2018-02-01

We investigate Titan's low-latitude and midlatitude surface using spectro-imaging near-infrared data from Cassini/Visual and Infrared Mapping Spectrometer. We use a radiative transfer code to first evaluate atmospheric contributions and then extract the haze and the surface albedo values of major geomorphological units identified in Cassini Synthetic Aperture Radar data, which exhibit quite similar spectral response to the Visual and Infrared Mapping Spectrometer data. We have identified three main categories of albedo values and spectral shapes, indicating significant differences in the composition among the various areas. We compare with linear mixtures of three components (water ice, tholin-like, and a dark material) at different grain sizes. Due to the limited spectral information available, we use a simplified model, with which we find that each albedo category of regions of interest can be approximately fitted with simulations composed essentially by one of the three surface candidates. Our fits of the data are overall successful, except in some cases at 0.94, 2.03, and 2.79 μm, indicative of the limitations of our simplistic compositional model and the need for additional components to reproduce Titan's complex surface. Our results show a latitudinal dependence of Titan's surface composition, with water ice being the major constituent at latitudes beyond 30°N and 30°S, while Titan's equatorial region appears to be dominated partly by a tholin-like or by a very dark unknown material. The albedo differences and similarities among the various geomorphological units give insights on the geological processes affecting Titan's surface and, by implication, its interior. We discuss our results in terms of origin and evolution theories.

Geomorphological and cryostratigraphical analyses of the Zackenberg Valley, NE Greenland and significance of Holocene alluvial fans

NASA Astrophysics Data System (ADS)

Cable, Stefanie; Christiansen, Hanne H.; Westergaard-Nielsen, Andreas; Kroon, Aart; Elberling, Bo

2018-02-01

In High Arctic northern Greenland, future responses to climatic changes are poorly understood on a landscape scale. Here, we present a study of the geomorphology and cryostratigraphy in the Zackenberg Valley in NE Greenland (74°N) containing a geomorphological map and a simplified geocryological map, combined with analyses of 13 permafrost cores and two exposures. Cores from a solifluction sheet, alluvial fans, and an emerged delta were studied with regards to cryostructures, ice and total carbon contents, grain size distribution, and pore water electrical conductivity; and the samples were AMS 14C dated. The near-surface permafrost on slopes and alluvial fans is ice rich, as opposed to the ice-poor epigenetic permafrost in the emerged delta. Ground ice and carbon distribution are closely linked to sediment transport processes, which largely depend on lithology and topography. Holocene alluvial fans on the lowermost hillslopes, covering 12% of the study area, represent paleoenvironmental archives. During the contrasting climates of the Holocene, the alluvial fans continued to aggrade - through the warmer early Holocene Optimum, the colder late Holocene, and the following climate warming - and by 0.45 mm a- 1, on average. This is caused by three factors: sedimentation, ground ice aggradation, and vegetation growth and is reflected by AMS 14C dating and continuously alternating cryostructures. Highly variable sedimentation rates in space and time at the alluvial fans have been detected. This is also reflected by alternating lenticular and microlenticular cryostructures indicating syngenetic permafrost aggradation during sedimentation with suspended and organic-matrix cryostructures indicating quasi-syngenetic permafrost aggradation in response to vegetation growth in periods with reduced or no sedimentation. Over time, this causes organic matter to become buried, indicating that alluvial fans represent effective carbon sinks that have previously been overlooked.

Causal Loop Analysis of coastal geomorphological systems

NASA Astrophysics Data System (ADS)

Payo, Andres; Hall, Jim W.; French, Jon; Sutherland, James; van Maanen, Barend; Nicholls, Robert J.; Reeve, Dominic E.

2016-03-01

As geomorphologists embrace ever more sophisticated theoretical frameworks that shift from simple notions of evolution towards single steady equilibria to recognise the possibility of multiple response pathways and outcomes, morphodynamic modellers are facing the problem of how to keep track of an ever-greater number of system feedbacks. Within coastal geomorphology, capturing these feedbacks is critically important, especially as the focus of activity shifts from reductionist models founded on sediment transport fundamentals to more synthesist ones intended to resolve emergent behaviours at decadal to centennial scales. This paper addresses the challenge of mapping the feedback structure of processes controlling geomorphic system behaviour with reference to illustrative applications of Causal Loop Analysis at two study cases: (1) the erosion-accretion behaviour of graded (mixed) sediment beds, and (2) the local alongshore sediment fluxes of sand-rich shorelines. These case study examples are chosen on account of their central role in the quantitative modelling of geomorphological futures and as they illustrate different types of causation. Causal loop diagrams, a form of directed graph, are used to distil the feedback structure to reveal, in advance of more quantitative modelling, multi-response pathways and multiple outcomes. In the case of graded sediment bed, up to three different outcomes (no response, and two disequilibrium states) can be derived from a simple qualitative stability analysis. For the sand-rich local shoreline behaviour case, two fundamentally different responses of the shoreline (diffusive and anti-diffusive), triggered by small changes of the shoreline cross-shore position, can be inferred purely through analysis of the causal pathways. Explicit depiction of feedback-structure diagrams is beneficial when developing numerical models to explore coastal morphological futures. By explicitly mapping the feedbacks included and neglected within a model, the modeller can readily assess if critical feedback loops are included.

Understanding volcanic geomorphology from derivatives and wavelet analysis: A case study at Miyakejima Volcano, Izu Islands, Japan

NASA Astrophysics Data System (ADS)

Gomez, C.

2018-04-01

From feature recognition to multiscale analysis, the human brain does this computation almost instantaneously, but reproducing this process for effective computation is still a challenge. Although it is a growing field in computational geomorphology, there has been only limited investigation of those issues on volcanoes. For the present study, we investigated Miyakejima, a volcanic island in the Izu archipelago, located 200 km south of Tokyo City (Japan). The island has experienced numerous Quaternary and historical eruptions, which have been recorded in details and therefore provide a solid foundation to experiment remote-sensing methods and compare the results to existing data. In the present study, the author examines the use of DEM derivatives and wavelet decomposition 5 m DEM available from the Geographic Authority of Japan was used. It was pre-processed to generate grid data with QGIS. The data was then analyzed with remote sensing techniques and wavelet analysis in ENVI and Matlab. Results have shown that the combination of 'Elevation' with 'Local Data Range Variation' and 'Relief Mapping' as a RGB image composite provides a powerful visual interpretation tool, but the feature separation remains a subjective analysis provided a more appropriate dataset for computer-based analysis and information extraction and understanding of topographic features at different scales. In order to confirm the usefulness of these topographic derivatives, the results were compared to known geological features and it was found to be in accordance with the data provided by geological, topographic maps and field research at Miyakejima. The protocol presented in the discussion can therefore be re-used at other volcanoes worldwide where less information is available on past-eruption and geology, in order to explain the volcanic geomorphology.

Application of ordinary kriging to reconstruct and visualise the relief in thelocation of an open pit sand mine. (Polish Title: Zastosowanie krigingu zwyczajnego do rekonstrukcji i wizualizacji reliefu w miejscach odkrywkowej eksploatacji piasku)

NASA Astrophysics Data System (ADS)

Zarychta, R.; Zarychta, A.

2013-12-01

Extraction of mineral resources, including rocks, usually causes some significant changes of the landscape. Transformation of the relief which character and scale can be analysed by means of cartographic materials seems to be the most interesting. Reconstruction of the relief of the period prior to the exploitation is a starting point for such investigation. It can be done basing on archival cartographic materials which are difficult to obtain. However, too varied morphological material of the area can lead to erroneous conclusions which suggests interpretation of three - dimensional models of the relief. Hence, the paper deals with reconstruction and visualisation of the relief (in the period before the exploitation) of four sand fields of the old sand mine excavation "Siemonia". A geological map of Poland (Wojkowice sheet) has been used for the purpose. A geostatical analysis by means of the programmes Surfer 8 and ArcGIS 10.1. has been performed on the map. An estimation method called ordinary kriging, which is related to B.L.U.E. (best linear unbiased estimator), where the condition of the lack of weight of the measurement (the sum of weight is equal to 1) is fulfilled, has been applied. The calculated values of errors (mean error, mean squared error and mean squared standardised error) obtained as a result of application of the cross - validation procedure are, to a large extent, in agreement with predetermined values of errors given by numerous authors in the scientific literature. It confirms proper "manual" adjustment of two mathematic al models of spherical variograms and empirical variograms. The generated contour map of the investigated area (based on estimated points of sampling in nodes of the interpolation grid) together with its three - dimensional digital model are more adequate (due to significant marking of the relief) to the previous state of the investigated area than the two other presented types of cartographic visualisations made without application of the geostatistical methods. Hence, the graphic presentation of results, mentioned as the last one, can be only applied to visualise the relief without any detailed geomorphological interpretations due to its inaccuracy. It seems to be obvious that detailed analyses can be performed basing on a digital model of the terrain accompanied by its contour map obtained when reconstruction of the relief is made by means of geostatistical methods (especially ordinary kriging).

Multidate remote sensing approaches for digital zoning of terroirs at regional scales: case studies revisited and perspectives

NASA Astrophysics Data System (ADS)

Vaudour, Emmanuelle; Carey, Victoria A.; Gilliot, Jean-Marc

2014-05-01

Geospatial technologies prove more and more useful for characterizing terroirs and this, not only at the within-field scale: amongst innovating technologies revolutionizing approaches for digitally zoning viticultural areas, be they managed by individual or cooperative grape growers, or even unions of grape growers, multispectral satellite remote sensing data have been used for 15 years already at either regional or whole-vineyard scale, starting from single date-studies to multi-temporal processings. Regional remotely-sensed approaches for terroir mapping mostly use multispectral satellite images in conjunction with a set of ancillary morphometric and/or geomorphological and/or legacy soil data and time series data on grape/wine quality and climate. Two prominent case-studies of regional terroir mapping using SPOT satellite images with medium spatial resolution (20 m) were carried out in the Southern Rhone Valley (Côtes-du-Rhône controlled Appelation of origin) in Southern France and in the Stellenbosch-Paarl region (including 5 Wine of Origin wards: Simonsberg-Stellenbosch, Simonsberg-Paarl, Jonkershoek Valley, Banghoek and Papegaaiberg and portions of two further wards, namely, Franschoek and Devon Valley) in the South Western Cape of South Africa. In addition to emphasizing their usefulness for operational land management, our objective was to develop, compare and discuss both approaches in terms of formalization, spatial data handling and processing, sampling design, validation procedures and/or availability of uncertainty information. Both approaches essentially relied on supervised image classifiers based on the selection of reference training areas. For the Southern Rhone valley, viticultural terroirs were validated using an external sample of 91 vineyards planted with Grenache Noir and Syrah for which grape composition was available over a large 17 years-period: the validation procedure highlighted a strong vintage effect for each specific terroir. The output map was appropriate at the scale of cooperative wineries and the scale of the union of grapegrowers. For the Stellenbosch-Paarl region, 55 Sauvignon Blanc vineyards previously characterized in terms of grape/vine/wine quality in several earlier studies were used to introduce expert knowledge as a basis for bootstrapped regression tree calculations, which enabled uncertainty assessment of final map results. Further perspectives related to the spatial monitoring of vine phenology according to the output terroir units and the possible characterization of both within/between terroir spatio-temporal variability of vegetative growth were initiated for the Southern Rhone terroirs considering a SPOT4-Take Five satellite time series acquired from February to June 2013 in the framework of the SPOT4-Take Five program of the French Space Agency (CNES).

Digital Mapping Techniques '08—Workshop Proceedings, Moscow, Idaho, May 18–21, 2008

USGS Publications Warehouse

Soller, David R.

2009-01-01

The Digital Mapping Techniques '08 (DMT'08) workshop was attended by more than 100 technical experts from 40 agencies, universities, and private companies, including representatives from 24 State geological surveys. This year's meeting, the twelfth in the annual series, was hosted by the Idaho Geological Survey, from May 18-21, 2008, on the University of Idaho campus in Moscow, Idaho. Each DMT workshop has been coordinated by the U.S. Geological Survey's National Geologic Map Database Project and the Association of American State Geologists (AASG). As in previous years' meetings, the objective was to foster informal discussion and exchange of technical information, principally in order to develop more efficient methods for digital mapping, cartography, GIS analysis, and information management. At this meeting, oral and poster presentations and special discussion sessions emphasized (1) methods for creating and publishing map products (here, "publishing" includes Web-based release); (2) field data capture software and techniques, including the use of LiDAR; (3) digital cartographic techniques; (4) migration of digital maps into ArcGIS Geodatabase format; (5) analytical GIS techniques; and (6) continued development of the National Geologic Map Database.

Geology of Point Reyes National Seashore and vicinity, California: a digital database

USGS Publications Warehouse

Clark, Jospeh C.; Brabb, Earl E.

1997-01-01

This Open-File report is a digital geologic map database. This pamphlet serves to introduce and describe the digital data. There is no paper map included in the Open-File report. The report does include, however, a PostScript plot file containing an image of the geologic map sheet with explanation, as well as the accompanying text describing the geology of the area. For those interested in a paper plot of information contained in the database or in obtaining the PostScript plot files, please see the section entitled 'For Those Who Aren't Familiar With Digital Geologic Map Databases' below. This digital map database, compiled from previously published and unpublished data and new mapping by the authors, represents the general distribution of surficial deposits and rock units in Point Reyes and surrounding areas. Together with the accompanying text file (pr-geo.txt or pr-geo.ps), it provides current information on the stratigraphy and structural geology of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:48,000 or smaller.

Staff - Jennifer E. Athey | Alaska Division of Geological & Geophysical

Science.gov Websites

multiple data management projects from digital field data collection to data compilation projects to Surveys Digital Data Series 14, http://doi.org/10.14509/photodb. http://doi.org/10.14509/29735 Athey, J.E increasing communication about digital geologic field mapping, in Soller, D.R., ed. Digital Mapping

Optical domain analog to digital conversion methods and apparatus

DOEpatents

Vawter, Gregory A

2014-05-13

Methods and apparatus for optical analog to digital conversion are disclosed. An optical signal is converted by mapping the optical analog signal onto a wavelength modulated optical beam, passing the mapped beam through interferometers to generate analog bit representation signals, and converting the analog bit representation signals into an optical digital signal. A photodiode receives an optical analog signal, a wavelength modulated laser coupled to the photodiode maps the optical analog signal to a wavelength modulated optical beam, interferometers produce an analog bit representation signal from the mapped wavelength modulated optical beam, and sample and threshold circuits corresponding to the interferometers produce a digital bit signal from the analog bit representation signal.

Taxonomic classification of soils using digital information from LANDSAT data. Huayllamarca and eucaliptus areas. M.S. Thesis - Bolivia Univ.

NASA Technical Reports Server (NTRS)

Quiroga, S. Q.

1977-01-01

The applicability of LANDSAT digital information to soil mapping is described. A compilation of all cartographic information and bibliography of the study area is made. LANDSAT MSS images on a scale of 1:250,000 are interpreted and a physiographic map with legend is prepared. The study area is inspected and a selection of the sample areas is made. A digital map of the different soil units is produced and the computer mapping units are checked against the soil units encountered in the field. The soil boundaries obtained by automatic mapping were not substantially changed by field work. The accuracy of the automatic mapping is rather high.

Introducing students to digital geological mapping: A workflow based on cheap hardware and free software

NASA Astrophysics Data System (ADS)

Vrabec, Marko; Dolžan, Erazem

2016-04-01

The undergraduate field course in Geological Mapping at the University of Ljubljana involves 20-40 students per year, which precludes the use of specialized rugged digital field equipment as the costs would be way beyond the capabilities of the Department. A different mapping area is selected each year with the aim to provide typical conditions that a professional geologist might encounter when doing fieldwork in Slovenia, which includes rugged relief, dense tree cover, and moderately-well- to poorly-exposed bedrock due to vegetation and urbanization. It is therefore mandatory that the digital tools and workflows are combined with classical methods of fieldwork, since, for example, full-time precise GNSS positioning is not viable under such circumstances. Additionally, due to the prevailing combination of complex geological structure with generally poor exposure, students cannot be expected to produce line (vector) maps of geological contacts on the go, so there is no need for such functionality in hardware and software that we use in the field. Our workflow therefore still relies on paper base maps, but is strongly complemented with digital tools to provide robust positioning, track recording, and acquisition of various point-based data. Primary field hardware are students' Android-based smartphones and optionally tablets. For our purposes, the built-in GNSS chips provide adequate positioning precision most of the time, particularly if they are GLONASS-capable. We use Oruxmaps, a powerful free offline map viewer for the Android platform, which facilitates the use of custom-made geopositioned maps. For digital base maps, which we prepare in free Windows QGIS software, we use scanned topographic maps provided by the National Geodetic Authority, but also other maps such as aerial imagery, processed Digital Elevation Models, scans of existing geological maps, etc. Point data, like important outcrop locations or structural measurements, are entered into Oruxmaps as waypoints. Students are also encouraged to directly measure structural data with specialized Android apps such as the MVE FieldMove Clino. Digital field data is exported from Oruxmaps to Windows computers primarily in the ubiquitous GPX data format and then integrated in the QGIS environment. Recorded GPX tracks are also used with the free Geosetter Windows software to geoposition and tag any digital photographs taken in the field. With minimal expenses, our workflow provides the students with basic familiarity and experience in using digital field tools and methods. The workflow is also practical enough for the prevailing field conditions of Slovenia that the faculty staff is using it in geological mapping for scientific research and consultancy work.

A physically based catchment partitioning method for hydrological analysis

NASA Astrophysics Data System (ADS)

Menduni, Giovanni; Riboni, Vittoria

2000-07-01

We propose a partitioning method for the topographic surface, which is particularly suitable for hydrological distributed modelling and shallow-landslide distributed modelling. The model provides variable mesh size and appears to be a natural evolution of contour-based digital terrain models. The proposed method allows the drainage network to be derived from the contour lines. The single channels are calculated via a search for the steepest downslope lines. Then, for each network node, the contributing area is determined by means of a search for both steepest upslope and downslope lines. This leads to the basin being partitioned into physically based finite elements delimited by irregular polygons. In particular, the distributed computation of local geomorphological parameters (i.e. aspect, average slope and elevation, main stream length, concentration time, etc.) can be performed easily for each single element. The contributing area system, together with the information on the distribution of geomorphological parameters provide a useful tool for distributed hydrological modelling and simulation of environmental processes such as erosion, sediment transport and shallow landslides.

Geomorphological origin of recession curves

NASA Astrophysics Data System (ADS)

Biswal, Basudev; Marani, Marco

2010-12-01

We identify a previously undetected link between the river network morphology and key recession curves properties through a conceptual-physical model of the drainage process of the riparian unconfined aquifer. We show that the power-law exponent, α, of -dQ/dt vs. Q curves is related to the power-law exponent of N(l) vs. G(l) curves (which we show to be connected to Hack's law), where l is the downstream distance from the channel heads, N(l) is the number of channel reaches exactly located at a distance l from their channel head, and G(l) is the total length of the network located at a distance greater or equal to l from channel heads. Using Digital Terrain Models and daily discharge observations from 67 US basins we find that geomorphologic α estimates match well the values obtained from recession curves analyses. Finally, we argue that the link between recession flows and network morphology points to an important role of low-flow discharges in shaping the channel network.

Quantifying climatic controls on river network topology across scales

NASA Astrophysics Data System (ADS)

Ranjbar Moshfeghi, S.; Hooshyar, M.; Wang, D.; Singh, A.

2017-12-01

Branching structure of river networks is an important topologic and geomorphologic feature that depends on several factors (e.g. climate, tectonic). However, mechanisms that cause these drainage patterns in river networks are poorly understood. In this study, we investigate the effects of varying climatic forcing on river network topology and geomorphology. For this, we select 20 catchments across the United States with different long-term climatic conditions quantified by climate aridity index (AI), defined here as the ratio of mean annual potential evaporation (Ep) to precipitation (P), capturing variation in runoff and vegetation cover. The river networks of these catchments are extracted, using a curvature-based method, from high-resolution (1 m) digital elevation models and several metrics such as drainage density, branching angle, and width functions are computed. We also use a multiscale-entropy-based approach to quantify the topologic irregularity and structural richness of these river networks. Our results reveal systematic impacts of climate forcing on the structure of river networks.

Digital image transformation and rectification of spacecraft and radar images

NASA Technical Reports Server (NTRS)

Wu, S. S. C.

1985-01-01

The application of digital processing techniques to spacecraft television pictures and radar images is discussed. The use of digital rectification to produce contour maps from spacecraft pictures is described; images with azimuth and elevation angles are converted into point-perspective frame pictures. The digital correction of the slant angle of radar images to ground scale is examined. The development of orthophoto and stereoscopic shaded relief maps from digital terrain and digital image data is analyzed. Digital image transformations and rectifications are utilized on Viking Orbiter and Lander pictures of Mars.

Geomorphology, active tectonics, and landscape evolution in the Mid-Atlantic region: Chapter

USGS Publications Warehouse

Pazzaglia, Frank J.; Carter, Mark W.; Berti, Claudio; Counts, Ronald C.; Hancock, Gregory S.; Harbor, David; Harrison, Richard W.; Heller, Matthew J.; Mahan, Shannon; Malenda, Helen; McKeon, Ryan; Nelson, Michelle S.; Prince, Phillip; Rittenour, Tammy M.; Spotilla, James; Whittecar, G. Richard

2015-01-01

In 2014, the geomorphology community marked the 125th birthday of one of its most influential papers, “The Rivers and Valleys of Pennsylvania” by William Morris Davis. Inspired by Davis’s work, the Appalachian landscape rapidly became fertile ground for the development and testing of several grand landscape evolution paradigms, culminating with John Hack’s dynamic equilibrium in 1960. As part of the 2015 GSA Annual Meeting, the Geomorphology, Active Tectonics, and Landscape Evolution field trip offers an excellent venue for exploring Appalachian geomorphology through the lens of the Appalachian landscape, leveraging exciting research by a new generation of process-oriented geomorphologists and geologic field mapping. Important geomorphologic scholarship has recently used the Appalachian landscape as the testing ground for ideas on long- and short-term erosion, dynamic topography, glacial-isostatic adjustments, active tectonics in an intraplate setting, river incision, periglacial processes, and soil-saprolite formation. This field trip explores a geologic and geomorphic transect of the mid-Atlantic margin, starting in the Blue Ridge of Virginia and proceeding to the east across the Piedmont to the Coastal Plain. The emphasis here will not only be on the geomorphology, but also the underlying geology that establishes the template and foundation upon which surface processes have etched out the familiar Appalachian landscape. The first day focuses on new and published work that highlights Cenozoic sedimentary deposits, soils, paleosols, and geomorphic markers (terraces and knickpoints) that are being used to reconstruct a late Cenozoic history of erosion, deposition, climate change, and active tectonics. The second day is similarly devoted to new and published work documenting the fluvial geomorphic response to active tectonics in the Central Virginia seismic zone (CVSZ), site of the 2011 M 5.8 Mineral earthquake and the integrated record of Appalachian erosion preserved on the Coastal Plain. The trip concludes on Day 3, joining the Kirk Bryan Field Trip at Great Falls, Virginia/ Maryland, to explore and discuss the dramatic processes of base-level fall, fluvial incision, and knickpoint retreat.

The Importance of Cultural Heritage in Earth Science

NASA Astrophysics Data System (ADS)

Avvisati, Gala; Di Vito, Mauro; Marotta, Enrica; Sangianantoni, Agata; Peluso, Rosario; de Vita, Sandro; Nave, Rosella; Vertechi, Enrico; De Natale, Giuseppe; Ghilardi, Massimo

2016-04-01

In recent years the Earth Sciences community is facing the need to achieve a more effective and efficient dissemination of its scientific culture. There is now a growing needing to integrate the use of "traditional" dissemination media of cultural heritage with the new digital technologies. Getting people involved in geoheritage site's activities represents a crucial issue in order to better communicate and increase the collective awareness of natural hazards, risk, and environmental change. The Reale Osservatorio Vesuviano (ROV) which is part of the Istituto Nazionale di Geofisica e Vulcanologia (INGV), owns collections unique in their combination of scientific, historical and artistic importance. The long history of ROV is extensively documented in its collections. This heritage - of great scientific and cultural value and unique for its abundance and variety - tells the story of the first observatory in the world, closely linked to the activity of Vesuvius, and the commitment of many scientists who dedicated their lives to study the volcano. The collections include: a) old books on volcanological matters, b) collection of rocks, minerals, volcanic ash and other materials from historical eruptions of Vesuvius, c) recordings on smoked paper of Vesuvius seismic activity from 1915 until 1970, d) scientific instruments, e) geological and geomorphological maps and models, f) vintage photographs and filmed sequences of eruptions, g) gouaches of Vesuvius and h) lava medals. The exposition of these collections, improved with the new digital contents, may trace new and unexplored routes for the dissemination of Earth Sciences related culture. The ethical duty of the ROV is the creation of an universal identity by taking a picture of the evolution of the society through the training of the culture of seismic and volcanic risk. A disappearance of its heritage could represent an huge impoverishment of its community: the ROV carries in fact the cultural identity of the inhabitants in its surroundings but also of all the people in the world as the global digital connections have broken down geographical and cultural barriers. The challenge to protect and preserve this cultural heritage is played on many fields: sociology, digital contents, heritage management and legal.

The influence of floodplain geomorphology and hydrologic connectivity on alligator gar (Atractosteus spatula) habitat along the embanked floodplain of the Lower Mississippi River

NASA Astrophysics Data System (ADS)

van der Most, Merel; Hudson, Paul F.

2018-02-01

The floodplain geomorphology of large lowland rivers is intricately related to aquatic ecosystems dependent upon flood pulse dynamics. The alligator gar (Atractosteus spatula) is native to the Lower Mississippi River and dependent upon floodplain backwater areas for spawning. In this study we utilize a geospatial approach to develop a habitat suitability index for alligator gar that explicitly considers hydrologic connectivity and the floodplain geomorphology along a frequently inundated segment of the Lower Mississippi River. The data sets include Landsat imagery, a high-resolution LiDAR digital elevation model (DEM), National Hydrography Dataset (NHD), and hydrologic and geomorphic data. A habitat suitability index is created based on the extent and frequency of inundation, water depth, temperature, and vegetation. A comparison between the remote sensing approach and the NHD revealed substantial differences in the area and location of water bodies available for alligator gar spawning. The final habitat suitability index indicates that a modest proportion (19%) of the overall embanked floodplain is available for alligator gar spawning. Opportunities exist for management efforts to utilize engineered and natural geomorphic features to facilitate hydrologic connectivity at flow levels below flood stage that would expand the habitat of alligator gar across the floodplain. The study results have direct implications regarding environmental restoration of the Lower Mississippi, an iconic example of an embanked meandering river floodplain.

Digital Geologic Map of the Wallace 1:100,000 Quadrangle, Idaho

USGS Publications Warehouse

Lewis, Reed S.; Burmester, Russell F.; McFaddan, Mark D.; Derkey, Pamela D.; Oblad, Jon R.

1999-01-01

The geology of the Wallace 1:100,000 quadrangle, Idaho was compiled by Reed S. Lewis in 1997 primarily from published materials including 1983 data from Foster, Harrison's unpublished mapping done from 1975 to 1985, Hietenan's 1963, 1967, 1968, and 1984 mapping, Hobbs and others 1965 mapping, and Vance's 1981 mapping, supplemented by eight weeks of field mapping by Reed S. Lewis, Russell F. Burmester, and Mark D. McFaddan in 1997 and 1998. This geologic map information was inked onto a 1:100,000-scale greenline mylar of the topographic base map for input into a geographic information system (GIS). The resulting digital geologic map GIS can be queried in many ways to produce a variety of geologic maps. Digital base map data files (topography, roads, towns, rivers and lakes, etc.) are not included: they may be obtained from a variety of commercial and government sources. This database is not meant to be used or displayed at any scale larger than 1:100,000 (e.g., 1:62,500 or 1:24,000). The map area is located in north Idaho. The primary sources of map data are shown in figure 2 and additional sources are shown in figure 3. This open-file report describes the geologic map units, the methods used to convert the geologic map data into a digital format, the Arc/Info GIS file structures and relationships, and explains how to download the digital files from the U.S. Geological Survey public access World Wide Web site on the Internet. Mapping and compilation was completed by the Idaho Geological Survey under contract with the U.S. Geological Survey (USGS) office in Spokane, Washington. The authors would like to acknowledge the help of the following field assistants: Josh Goodman, Yvonne Issak, Jeremy Johnson and Kevin Myer. Don Winston provided help with our ongoing study of Belt stratigraphy, and Tom Frost assisted with logistical problems and sample collection. Manuscript reviews by Steve Box, Tom Frost, and Brian White are greatly appreciated. We wish to thank Karen S. Bolm of the USGS for reviewing the digital files.

Qualitative landslide susceptibility assessment by multicriteria analysis: A case study from San Antonio del Sur, Guantánamo, Cuba

NASA Astrophysics Data System (ADS)

Castellanos Abella, Enrique A.; Van Westen, Cees J.

Geomorphological information can be combined with decision-support tools to assess landslide hazard and risk. A heuristic model was applied to a rural municipality in eastern Cuba. The study is based on a terrain mapping units (TMU) map, generated at 1:50,000 scale by interpretation of aerial photos, satellite images and field data. Information describing 603 terrain units was collected in a database. Landslide areas were mapped in detail to classify the different failure types and parts. Three major landslide regions are recognized in the study area: coastal hills with rockfalls, shallow debris flows and old rotational rockslides denudational slopes in limestone, with very large deep-seated rockslides related to tectonic activity and the Sierra de Caujerí scarp, with large rockslides. The Caujerí scarp presents the highest hazard, with recent landslides and various signs of active processes. The different landforms and the causative factors for landslides were analyzed and used to develop the heuristic model. The model is based on weights assigned by expert judgment and organized in a number of components such as slope angle, internal relief, slope shape, geological formation, active faults, distance to drainage, distance to springs, geomorphological subunits and existing landslide zones. From these variables a hierarchical heuristic model was applied in which three levels of weights were designed for classes, variables, and criteria. The model combines all weights into a single hazard value for each pixel of the landslide hazard map. The hazard map was then divided by two scales, one with three classes for disaster managers and one with 10 detailed hazard classes for technical staff. The range of weight values and the number of existing landslides is registered for each class. The resulting increasing landslide density with higher hazard classes indicates that the output map is reliable. The landslide hazard map was used in combination with existing information on buildings and infrastructure to prepare a qualitative risk map. The complete lack of historical landslide information and geotechnical data precludes the development of quantitative deterministic or probabilistic models.

Transfer of Technology for Cadastral Mapping in Tajikistan Using High Resolution Satellite Data

NASA Astrophysics Data System (ADS)

Kaczynski, R.

2012-07-01

European Commission funded project entitled: "Support to the mapping and certification capacity of the Agency of Land Management, Geodesy and Cartography" in Tajikistan was run by FINNMAP FM-International and Human Dynamics from Nov. 2006 to June 2011. The Agency of Land Management, Geodesy and Cartography is the state agency responsible for development, implementation, monitoring and evaluation of state policies on land tenure and land management, including the on-going land reform and registration of land use rights. The specific objective was to support and strengthen the professional capacity of the "Fazo" Institute in the field of satellite geodesy, digital photogrammetry, advanced digital satellite image processing of high resolution satellite data and digital cartography. Lectures and on-the-job trainings for the personnel of "Fazo" and Agency in satellite geodesy, digital photogrammetry, cartography and the use of high resolution satellite data for cadastral mapping have been organized. Standards and Quality control system for all data and products have been elaborated and implemented in the production line. Technical expertise and trainings in geodesy, photogrammetry and satellite image processing to the World Bank project "Land Registration and Cadastre System for Sustainable Agriculture" has also been completed in Tajikistan. The new map projection was chosen and the new unclassified geodetic network has been established for all of the country in which all agricultural parcel boundaries are being mapped. IKONOS, QuickBird and WorldView1 panchromatic data have been used for orthophoto generation. Average accuracy of space triangulation of non-standard (long up to 90km) satellite images of QuickBird Pan and IKONOS Pan on ICPs: RMSEx = 0.5m and RMSEy = 0.5m have been achieved. Accuracy of digital orthophoto map is RMSExy = 1.0m. More then two and half thousands of digital orthophoto map sheets in the scale of 1:5000 with pixel size 0.5m have been produced so far by the "Fazo" Institute in Tajikistan on the basis of technology elaborated in the framework of this project. Digital cadastral maps are produced in "Fazo" and Cadastral Regional Centers in Tajikistan using ArcMap software. These digital orthophotomaps will also be used for digital mapping of water resources and other needs of the country.

Comparing Tactile Maps and Haptic Digital Representations of a Maritime Environment

ERIC Educational Resources Information Center

Simonnet, Mathieu; Vieilledent, Steephane; Jacobson, R. Daniel; Tisseau, Jacques

2011-01-01

A map exploration and representation exercise was conducted with participants who were totally blind. Representations of maritime environments were presented either with a tactile map or with a digital haptic virtual map. We assessed the knowledge of spatial configurations using a triangulation technique. The results revealed that both types of…

Digital terrain tapes: user guide

USGS Publications Warehouse

,

1980-01-01

DMATC's digital terrain tapes are a by-product of the agency's efforts to streamline the production of raised-relief maps. In the early 1960's DMATC developed the Digital Graphics Recorder (DGR) system that introduced new digitizing techniques and processing methods into the field of three-dimensional mapping. The DGR system consisted of an automatic digitizing table and a computer system that recorded a grid of terrain elevations from traces of the contour lines on standard topographic maps. A sequence of computer accuracy checks was performed and then the elevations of grid points not intersected by contour lines were interpolated. The DGR system produced computer magnetic tapes which controlled the carving of plaster forms used to mold raised-relief maps. It was realized almost immediately that this relatively simple tool for carving plaster molds had enormous potential for storing, manipulating, and selectively displaying (either graphically or numerically) a vast number of terrain elevations. As the demand for the digital terrain tapes increased, DMATC began developing increasingly advanced digitizing systems and now operates the Digital Topographic Data Collection System (DTDCS). With DTDCS, two types of data elevations as contour lines and points, and stream and ridge lines are sorted, matched, and resorted to obtain a grid of elevation values for every 0.01 inch on each map (approximately 200 feet on the ground). Undefined points on the grid are found by either linear or or planar interpolation.

Logistic Regression for Seismically Induced Landslide Predictions: Using Uniform Hazard and Geophysical Layers as Predictor Variables

NASA Astrophysics Data System (ADS)

Nowicki, M. A.; Hearne, M.; Thompson, E.; Wald, D. J.

2012-12-01

Seismically induced landslides present a costly and often fatal threats in many mountainous regions. Substantial effort has been invested to understand where seismically induced landslides may occur in the future. Both slope-stability methods and, more recently, statistical approaches to the problem are described throughout the literature. Though some regional efforts have succeeded, no uniformly agreed-upon method is available for predicting the likelihood and spatial extent of seismically induced landslides. For use in the U. S. Geological Survey (USGS) Prompt Assessment of Global Earthquakes for Response (PAGER) system, we would like to routinely make such estimates, in near-real time, around the globe. Here we use the recently produced USGS ShakeMap Atlas of historic earthquakes to develop an empirical landslide probability model. We focus on recent events, yet include any digitally-mapped landslide inventories for which well-constrained ShakeMaps are also available. We combine these uniform estimates of the input shaking (e.g., peak acceleration and velocity) with broadly available susceptibility proxies, such as topographic slope and surface geology. The resulting database is used to build a predictive model of the probability of landslide occurrence with logistic regression. The landslide database includes observations from the Northridge, California (1994); Wenchuan, China (2008); ChiChi, Taiwan (1999); and Chuetsu, Japan (2004) earthquakes; we also provide ShakeMaps for moderate-sized events without landslide for proper model testing and training. The performance of the regression model is assessed with both statistical goodness-of-fit metrics and a qualitative review of whether or not the model is able to capture the spatial extent of landslides for each event. Part of our goal is to determine which variables can be employed based on globally-available data or proxies, and whether or not modeling results from one region are transferrable to geomorphologically-similar regions that lack proper calibration events. Combined with near-real time ShakeMaps, we anticipate using our model to make generalized predictions of whether or not (and if so, where) landslides are likely to occur for earthquakes around the globe; we also intend to incorporate this functionality into the USGS PAGER system.

Landslide Susceptibility Mapping of Tegucigalpa, Honduras Using Artificial Neural Network, Bayesian Network and Decision Trees

NASA Astrophysics Data System (ADS)

Garcia Urquia, E. L.; Braun, A.; Yamagishi, H.

2016-12-01

Tegucigalpa, the capital city of Honduras, experiences rainfall-induced landslides on a yearly basis. The high precipitation regime and the rugged topography the city has been built in couple with the lack of a proper urban expansion plan to contribute to the occurrence of landslides during the rainy season. Thousands of inhabitants live at risk of losing their belongings due to the construction of precarious shelters in landslide-prone areas on mountainous terrains and next to the riverbanks. Therefore, the city is in the need for landslide susceptibility and hazard maps to aid in the regulation of future development. Major challenges in the context of highly dynamic urbanizing areas are the overlap of natural and anthropogenic slope destabilizing factors, as well as the availability and accuracy of data. Data-driven multivariate techniques have proven to be powerful in discovering interrelations between factors, identifying important factors in large datasets, capturing non-linear problems and coping with noisy and incomplete data. This analysis focuses on the creation of a landslide susceptibility map using different methods from the field of data mining, Artificial Neural Networks (ANN), Bayesian Networks (BN) and Decision Trees (DT). The input dataset of the study contains geomorphological and hydrological factors derived from a digital elevation model with a 10 m resolution, lithological factors derived from a geological map, and anthropogenic factors, such as information on the development stage of the neighborhoods in Tegucigalpa and road density. Moreover, a landslide inventory map that was developed in 2014 through aerial photo interpretation was used as target variable in the analysis. The analysis covers an area of roughly 100 km2, while 8.95 km2 are occupied by landslides. In a first step, the dataset was explored by assessing and improving the data quality, identifying unimportant variables and finding interrelations. Then, based on a training partition of the dataset, the ANN, BN and DT were optimized for the prediction of landslides. The predictive power and ability to generalize of the resulting models were assessed in a test partition and evaluated using success rate curves, skill scores and by ensuring the spatial plausibility of the prediction.

Mapping and Mitigating the International Rip Current Health Hazard

NASA Astrophysics Data System (ADS)

Trimble, S. M.; Houser, C.

2016-12-01

Rip currents are concentrated seaward flows of water originating in the surf zones of beaches. Rips cause hundreds of international drownings each year. Calculating exact numbers is barred by logistical difficulties in obtaining accurate incident reports, but annual rip current fatalities are estimated at 100, 53 and 21 in the United States (US), Costa Rica, and Australia respectively. Notably, Australia's lifeguards rescue 17,600 swimmers from rips each year. This project addresses the geophysical, social, and systematic causes of fatalities in hopes of decreasing the global number of rip-related deaths. We demonstrate a novel method for mapping bathymetry in the surf zone (20m deep or less), specifically within rip channels (topographic low spots in the nearshore that result from feedback amongst waves, substrate, and antecedent bathymetry). We calculate bathymetry using 8-band multispectral imagery from the Digital Globe WorldView2 (WV2) satellite and field measurements of depth, generating maps of the changing nearshore at two embayed, rip-prone beaches: Playa Cocles, Costa Rica, and Bondi Beach, Australia. WV2 has a 1.1 day pass-over rate with 1.84m ground pixel resolution of 8 bands, including `yellow' (585-625 nm) and `coastal blue' (400-450 nm). Methods are tested for consistency amongst dates and locations. Previous research shows drownings result from a combination of the physical environment with personal and group behaviors; for this reason we build on rip-detection by evaluating tourists' and locals' knowledge and understanding of their beach's rip behavior. By combining the geomorphologic maps developed from WV2 with interview data, we evaluate how the physical environment dictates the exposure of certain swimmers. Controls include rip channel location, beach access points, and environmental factors favored by swimmers. The project serves as an evaluation of the landscape's creation of a physical feature that becomes a hazard when vulnerable humans swim into it. Results are meant to inform policy makers so that they may implement the methods: developing frequent nearshore maps to observe rip channel behavior, designing beach access controls informed by morphology, posting informative signs in ideal locations, and funding lifeguard programs.

Digital geologic map database of the Nevada Test Site area, Nevada

USGS Publications Warehouse

Wahl, R.R.; Sawyer, D.A.; Minor, S.A.; Carr, M.D.; Cole, J.C.; Swadley, W.C.; Laczniak, R.J.; Warren, R.G.; Green, K.S.; Engle, C.M.

1997-01-01

Forty years of geologic investigations at the Nevada Test Site (NTS) have been digitized. These data include all geologic information that: (1) has been collected, and (2) can be represented on a map within the map borders at the map scale is included in the map digital coverages. The following coverages are included with this dataset: Coverage Type Description geolpoly Polygon Geologic outcrops geolflts line Fault traces geolatts Point Bedding attitudes, etc. geolcald line Caldera boundaries geollins line Interpreted lineaments geolmeta line Metamorphic gradients The above coverages are attributed with numeric values and interpreted information. The entity files documented below show the data associated with each coverage.

Land use and land cover digital data from 1:250,000- and 1:100,000- scale maps

USGS Publications Warehouse

,

1990-01-01

The Earth Science Information Centers (ESIC) distribute digital cartographic/geographic data files produced by the U.S. Geological Survey (USGS) as part of the National Mapping Program. The data files are grouped into four basic types. The first type, called a Digital Line Graph (DLG), is line map information in digital form. These data files include information on planimetric base categories, such as transportation, hydrography, and boundaries. The second type, called a Digital Elevation Model (DEM), consists of a sampled array of elevations for ground positions that are usually at regularly spaced intervals. The third type, Land Use and Land Cover digital data, provide information on nine major classes of land use such as urban, agricultural, or forest as well as associated map data such as political units and Federal land ownership. The fourth type, the Geographic Names Information System, provides primary information for known places, features, and areas in the United States identified by a proper name.

The influence of control parameter estimation on large scale geomorphological interpretation of pointclouds

NASA Astrophysics Data System (ADS)

Dorninger, P.; Koma, Z.; Székely, B.

2012-04-01

In recent years, laser scanning, also referred to as LiDAR, has proved to be an important tool for topographic data acquisition. Basically, laser scanning acquires a more or less homogeneously distributed point cloud. These points represent all natural objects like terrain and vegetation as well as man-made objects such as buildings, streets, powerlines, or other constructions. Due to the enormous amount of data provided by current scanning systems capturing up to several hundred thousands of points per second, the immediate application of such point clouds for large scale interpretation and analysis is often prohibitive due to restrictions of the hard- and software infrastructure. To overcome this, numerous methods for the determination of derived products do exist. Commonly, Digital Terrain Models (DTM) or Digital Surface Models (DSM) are derived to represent the topography using a regular grid as datastructure. The obvious advantages are a significant reduction of the amount of data and the introduction of an implicit neighborhood topology enabling the application of efficient post processing methods. The major disadvantages are the loss of 3D information (i.e. overhangs) as well as the loss of information due to the interpolation approach used. We introduced a segmentation approach enabling the determination of planar structures within a given point cloud. It was originally developed for the purpose of building modeling but has proven to be well suited for large scale geomorphological analysis as well. The result is an assignment of the original points to a set of planes. Each plane is represented by its plane parameters. Additionally, numerous quality and quantity parameters are determined (e.g. aspect, slope, local roughness, etc.). In this contribution, we investigate the influence of the control parameters required for the plane segmentation on the geomorphological interpretation of the derived product. The respective control parameters may be determined either automatically (i.e. estimated of the given data) or manually (i.e. supervised parameter estimation). Additionally, the result might be influenced if data processing is performed locally (i.e. using tiles) or globally. Local processing of the data has the advantages of generally performing faster, having less hardware requirements, and enabling the determination of more detailed information. By contrast, especially in geomorphological interpretation, a global data processing enables determining large scale relations within the dataset analyzed. We investigated the influence of control parameter settings on the geomorphological interpretation on airborne and terrestrial laser scanning data sets of the landslide at Doren (Vorarlberg, Austria), on airborne laser scanning data of the western cordilleras of the central Andes, and on HRSC terrain data of the Mars surface. Topics discussed are the suitability of automated versus manual determination of control parameters, the influence of the definition of the area of interest (local versus global application) as well as computational performance.

Deciphering Fluvial-Capture-Induced Erosional Patterns at the Continental Scale on the Iberian Peninsula

NASA Astrophysics Data System (ADS)

Anton, L.; Munoz Martin, A.; De Vicente, G.; Finnegan, N. J.

2017-12-01

The process of river incision into bedrock dictates the landscape response to changes in climate and bedrock uplift in most unglaciated settings. Hence, understanding processes of river incision into bedrock and their topographic signatures are a basic goal of geomorphology. Formerly closed drainage basins provide an exceptional setting for the quantification of long term fluvial dissection and landscape change, making them valuable natural laboratories. Internally drained basins are peculiar because they trap all the sediment eroded within the watershed; as closed systems they do not respond to the base level of the global ocean and deposition is the dominant process. In that context, the opening of an outward drainage involves a sudden lowering of the base level, which is transmitted upstream along fluvial channels in the form of erosional waves, leading to high incision and denudation rates within the intrabasinal areas. Through digital topographic analysis and paleolandscape reconstruction based on relict deposits and landscapes on the Iberian Peninsula, we quantify the volume of sediments eroded from formerly internally drained basins since capture. Mapping of fluvial dissection patterns reveals how, and how far, regional waves of incision have propagated upstream. In our analysis, erosional patterns are consistent with the progressive establishment of an outward drainage system, providing a relative capture chronology for the different studied basins. Divide migration inferred from chi maps supports the interpretations based on fluvial dissection patterns and volumes, providing clues on how landscaped changed and how drainage integration occurred within the studied watersheds. [Funded by S2013/MAE-2739 and CGL2014-59516].

Pilot monitoring program: geologic input for the hillslope component (includes a discussion of Caspar Creek geology and geomorphology)

Treesearch

T. E. Spittler

1995-01-01

The California Department of Conservation, Division of Mines and Geology (DMG) is submitting this report and accompanying maps to the California Department of Forestry and Fire Protection (CDF) to fulfill Interagency Agreement number 8CA38400, Pilot Monitoring Program -- Geologic Input for the Hillslope Component. Under this agreement, DMG has assisted CDF in the...

The French Atlantic Littoral and the Massif Armoricain

NASA Technical Reports Server (NTRS)

Verger, F. (Principal Investigator); Monget, J. M.; Scanvic, J. Y.

1976-01-01

The author has identified the following significant results. Diachronic use of LANDSAT data time series will in time allow statistical study of submersion frequencies in tidal areas. This is an essential element of coastal geomorphology and of coastal zone management being particularly useful in siting shellfish farms. Maps are being obtained at useable scales and simple, user oriented legends which can be used for coastal planning.

California State Waters Map Series: offshore of Refugio Beach, California

USGS Publications Warehouse

Johnson, Samuel Y.; Dartnell, Peter; Cochrane, Guy R.; Golden, Nadine E.; Phillips, Eleyne L.; Ritchie, Andrew C.; Krigsman, Lisa M.; Dieter, Bryan E.; Conrad, James E.; Greene, H. Gary; Seitz, Gordon G.; Endris, Charles A.; Sliter, Ray W.; Wong, Florence L.; Erdey, Mercedes D.; Gutierrez, Carlos I.; Yoklavich, Mary M.; East, Amy E.; Hart, Patrick E.; Johnson, Samuel Y.; Cochran, Susan A.

2015-01-01

Seafloor habitats in the broad Santa Barbara Channel region consist of significant amounts of soft, unconsolidated sediment interspersed with isolated areas of rocky habitat that support kelp-forest communities nearshore and rocky-reef communities in deep water. The potential marine benthic habitat types mapped in the Offshore of Refugio Beach map area are directly related to its Quaternary geologic history, geomorphology, and active sedimentary processes. These potential habitats, which lie primarily within the Shelf (continental shelf) but also partly within the Flank (basin flank or continental slope) megahabitats, primarily are composed of soft sediment interrupted by a few carbonate mounds. This homogeneous seafloor of sediment and low-relief bedrock provides promising habitat for groundfish, crabs, shrimp, and other marine benthic organisms.

Multibeam mapping of the Pinnacles region, Gulf of Mexico

USGS Publications Warehouse

Gardner, James V.; Dartnell, Peter; Sulak, Kenneth J.

2002-01-01

Recent USGS mapping shows an extensive deep (~100 m) reef tract occurs on the Mississippi-Alabama outer continental shelf (Figure 1). The tract, known as "The Pinnacles", is apparently part of a sequence of drowned reef complexes along the "40-fathom" shelf edge of the northern Gulf of Mexico (Ludwick and Walton, 1957). It is critical to determine the accurate geomorphology of these deep-reefs because of their importance as benthic habitats for fisheries. The Pinnacles have previously been mapped using a single-beam echo sounder (Ludwick and Walton,1957), sidescan sonar (Laswell et al., 1990), and the TAMU2 towed single-beam sidescan-sonar system (Anonymous, 1999). These existing studies do not provide the quality of geomorphic data necessary for reasonable habitat studies.

Reply to the discussion by Pinyol et al. (2016) on Gutiérrez et al. (2015) "Large landslides associated with a diapiric fold in Canelles Reservoir (Spanish Pyrenees): Detailed geological-geomorphological mapping, trenching and electrical resistivity imaging"

NASA Astrophysics Data System (ADS)

Gutiérrez, Francisco; Linares, Rogelio; Roqué, Carles; Zarroca, Mario; Carbonel, Domingo; Rosell, Joan; Gutiérrez, Mateo

2016-06-01

Gutiérrez et al. (2015) in their paper published in Geomorphology document for the first time five large landslides (L1, L2, L3, L5, L6) in the Canelles Reservoir (Spanish Pyrenees) on the basis of detailed geomorphological-geological mapping. They also analyse a large 40 × 106 m3 translational landslide reactivated in 2006 by a severe decline in the reservoir water level (L4 or Canelles landslide). This landslide was discovered because a 1.1 km long fissure-scarp less than 0.5 m in width and height developed along the head of the landslide. The investigation concerning the Canelles landslide included the construction of site-specific stratigraphic columns, detailed mapping, electrical resistivity imaging, and trenching in the upper part of the landslide. The retrodeformation analysis of the trench log together with radiocarbon dates revealed two displacement events older and larger in magnitude than the 2006 event. Those episodes occurred in the 6th to 7th Centuries and in 1262-1679 yr AD, the latter one probably triggered by the 1373 Ribagorza earthquake (Mw 6.2). Based on these new data, Gutiérrez et al. (2015) discuss the hypothesis proposed in a previous paper by Pinyol et al. (2012) on the kinematic behaviour of the Canelles landslide. Pinyol et al. (2012), based on a thermo-hydro-mechanical numerical model that assumes dilation in the sliding surface induced by frictional heating under undrained conditions, predict a catastrophic reactivation. They forecast that at 35 s after the initiation of the movement, the landslide would reach a displacement of 250 m and a speed of 16 m s- 1, capable of generating an impulse-water wave (tsunami). Pinyol et al. (2016) address three issues in their discussion on Gutiérrez et al. (2015): (1) the geological model used; (2) the validity of the prediction of an extremely rapid reactivation; (3) the effectiveness of the corrective measures proposed. They also add a section with additional comments.

A digital version of the 1970 U.S. Geological Survey topographic map of the San Francisco Bay region, three sheets, 1:125,000

USGS Publications Warehouse

Aitken, Douglas S.

1997-01-01

This Open-File report is a digital topographic map database. It contains a digital version of the 1970 U.S. Geological Survey topographic map of the San Francisco Bay Region (3 sheets), at a scale of 1:125,000. These ARC/INFO coverages are in vector format. The vectorization process has distorted characters representing letters and numbers, as well as some road and other symbols, making them difficult to read in some instances. This pamphlet serves to introduce and describe the digital data. There is no paper map included in the Open-File report. The content and character of the database and methods of obtaining it are described herein.

The glacial geomorphology of the Lago Buenos Aires and Lago Puerreydón ice lobes, Central Patagonia

NASA Astrophysics Data System (ADS)

Bendle, Jacob; Thorndycraft, Varyl; Palmer, Adrian

2016-04-01

Patagonia is ideally located for reconstructions of late Quaternary ice-climate interaction(s) in the Southern Hemisphere mid-latitudes, yet many questions remain concerning post-LGM ice sheet retreat dynamics across the region. While modern-day glaciation is restricted to three small icefields (the North and South Patagonian and Cordillera Darwin icefields), during the Quaternary, and at the LGM, episodes of significant ice advance culminated in an expansive Patagonian ice sheet (PIS) centered over the southern Andes, for which a long and well-preserved landform record exists. Previous mapping in the region has either aimed to achieve regional coverage, necessarily omitting more subtle/complex features suggestive of certain ice-marginal processes, or has focused on the identification of palaeo-ice limits (e.g. moraine ridges) for geochronological applications, with little attention given to other (e.g. glaciofluvial, glaciolacustrine) features that are significant for understanding post-LGM ice sheet retreat dynamics. This poster presents a comprehensive and highly detailed (<30m spatial resolution) map of the glacial geomorphology of the Lago Buenos Aires (46.4°S) and Lago Puerreydón (47.2°S) ice lobes, major outlet glaciers of the central sector of the former PIS. The map allows refined reconstructions of glacial and, in particular, deglacial ice-marginal processes, and will underpin further analysis on the retreat history of the palaeo-ice lobes using high-resolution lithostratigraphic (varve) analyses.

The geomorphology of the Chandeleur Island Wetlands

DOE Office of Scientific and Technical Information (OSTI.GOV)

Debusschere, K.; Penland, S.; Westphal, K.

1990-09-01

The Chandeleur Islands represent the largest and oldest transgressive barrier island arc in the northern Gulf of Mexico. Generated by the transgressive submergence of the St. Bernard delta complex, the Chandeleur Islands form the protective geologic framework for one of the richest areas of salt marsh and seagrass flats in Louisiana. The Chandeleur barrier island arc is 60 km long and consists of five individual islands backed by a linear, multiple bar system enclosing a shallow basin floored by extensive seagrass flats. The northern part of the Chandeleur chain is the highest in relief, elevation, width, and habitat diversity. Nonstormmore » morphology is predominantly a combination of continuous dunes and dune terraces. Numerous washover channels and large washover fans extend into the backbarrier environment. Further south, the island width decreases and washover flats and terraces dominate the shoreline morphology In the southernmost section, the island arc is fragmented into a series of small islands and shoals separated by tidal inlets. Between 1984 and 1989, aerial videotape, aerial photographic, and bathymetric surveys were used to map and monitor the geomorphic changes occurring along the shoreline and in backbarrier areas. The aerial videotape mapping surveys focused on the impacts of hurricanes Danny, Elena, and Juan on the geomorphology of the islands. Videotape imagery was acquired in July 1984 and in July (prestorm), August (post-Danny), September (post-Elena), and November (post-Juan) 1985. A coastal geomorphic classification was developed to map the spatial and temporal landscape changes between surveys.« less

Application of Remote Sensing for Generation of Groundwater Prospect Map

NASA Astrophysics Data System (ADS)

Inayathulla, Masool

2016-07-01

In developing accurate hydrogeomorphological analysis, monitoring, ability to generate information in spatial and temporal domain and delineation of land features are crucial for successful analysis and prediction of groundwater resources. However, the use of RS and GIS in handling large amount of spatial data provides to gain accurate information for delineating the geological and geomorphological characteristics and allied significance, which are considered as a controlling factor for the occurrence and movement of groundwater used IRS LISS II data on 1: 50000 scale along with topographic maps in various parts of India to develop integrated groundwater potential zones. The present work is an attempt to integrate RS and GIS based analysis and methodology in groundwater potential zone identification in the Arkavathi Basin, Bangalore, study area. The information on geology, geomorphology, soil, slope, rainfall, water level and land use/land cover was gathered, in addition, GIS platform was used for the integration of various themes. The composite map generated was further classified according to the spatial variation of the groundwater potential. Five categories of groundwater potential zones namely poor, moderate to poor, moderate, good and very good were identified and delineated. The hydrogeomorphological units like valley fills and alluvial plain and are potential zones for groundwater exploration and development and valley fills associated with lineaments is highly promising area for ground water recharging. The spatial variation of the potential indicates that groundwater occurrence is controlled by geology, land use / land cover, slope and landforms.

The digital geologic map of Colorado in ARC/INFO format, Part A. Documentation

USGS Publications Warehouse

Green, Gregory N.

1992-01-01

This geologic map was prepared as a part of a study of digital methods and techniques as applied to complex geologic maps. The geologic map was digitized from the original scribe sheets used to prepare the published Geologic Map of Colorado (Tweto 1979). Consequently the digital version is at 1:500,000 scale using the Lambert Conformal Conic map projection parameters of the state base map. Stable base contact prints of the scribe sheets were scanned on a Tektronix 4991 digital scanner. The scanner automatically converts the scanned image to an ASCII vector format. These vectors were transferred to a VAX minicomputer, where they were then loaded into ARC/INFO. Each vector and polygon was given attributes derived from the original 1979 geologic map. This database was developed on a MicroVAX computer system using VAX V 5.4 nd ARC/INFO 5.0 software. UPDATE: April 1995, The update was done solely for the purpose of adding the abilitly to plot to an HP650c plotter. Two new ARC/INFO plot AMLs along with a lineset and shadeset for the HP650C design jet printer have been included. These new files are COLORADO.650, INDEX.650, TWETOLIN.E00 and TWETOSHD.E00. These files were created on a UNIX platform with ARC/INFO 6.1.2. Updated versions of INDEX.E00, CONTACT.E00, LINE.E00, DECO.E00 and BORDER.E00 files that included the newly defined HP650c items are also included. * Any use of trade, product, or firm names is for descriptive purposes only and does not imply endorsement by the U.S. Government. Descriptors: The Digital Geologic Map of Colorado in ARC/INFO Format Open-File Report 92-050

The digital geologic map of Colorado in ARC/INFO format, Part B. Common files

USGS Publications Warehouse

Green, Gregory N.

1992-01-01

This geologic map was prepared as a part of a study of digital methods and techniques as applied to complex geologic maps. The geologic map was digitized from the original scribe sheets used to prepare the published Geologic Map of Colorado (Tweto 1979). Consequently the digital version is at 1:500,000 scale using the Lambert Conformal Conic map projection parameters of the state base map. Stable base contact prints of the scribe sheets were scanned on a Tektronix 4991 digital scanner. The scanner automatically converts the scanned image to an ASCII vector format. These vectors were transferred to a VAX minicomputer, where they were then loaded into ARC/INFO. Each vector and polygon was given attributes derived from the original 1979 geologic map. This database was developed on a MicroVAX computer system using VAX V 5.4 nd ARC/INFO 5.0 software. UPDATE: April 1995, The update was done solely for the purpose of adding the abilitly to plot to an HP650c plotter. Two new ARC/INFO plot AMLs along with a lineset and shadeset for the HP650C design jet printer have been included. These new files are COLORADO.650, INDEX.650, TWETOLIN.E00 and TWETOSHD.E00. These files were created on a UNIX platform with ARC/INFO 6.1.2. Updated versions of INDEX.E00, CONTACT.E00, LINE.E00, DECO.E00 and BORDER.E00 files that included the newly defined HP650c items are also included. * Any use of trade, product, or firm names is for descriptive purposes only and does not imply endorsement by the U.S. Government. Descriptors: The Digital Geologic Map of Colorado in ARC/INFO Format Open-File Report 92-050

Quantification of soil mapping by digital analysis of LANDSAT data. [Clinton County, Indiana

NASA Technical Reports Server (NTRS)

Kirschner, F. R.; Kaminsky, S. A.; Hinzel, E. J.; Sinclair, H. R.; Weismiller, R. A.

1977-01-01

Soil survey mapping units are designed such that the dominant soil represents the major proportion of the unit. At times, soil mapping delineations do not adequately represent conditions as stated in the mapping unit descriptions. Digital analysis of LANDSAT multispectral scanner (MSS) data provides a means of accurately describing and quantifying soil mapping unit composition. Digital analysis of LANDSAT MSS data collected on 9 June 1973 was used to prepare a spectral soil map for a 430-hectare area in Clinton County, Indiana. Fifteen spectral classes were defined, representing 12 soil and 3 vegetation classes. The 12 soil classes were grouped into 4 moisture regimes based upon their spectral responses; the 3 vegetation classes were grouped into one all-inclusive class.

Map showing geologic terranes of the Hailey 1 degree x 2 degrees quadrangle and the western part of the Idaho Falls 1 degree x 2 degrees quadrangle, south-central Idaho

USGS Publications Warehouse

Worl, R.G.; Johnson, K.M.

1995-01-01

The paper version of Map Showing Geologic Terranes of the Hailey 1x2 Quadrangle and the western part of the Idaho Falls 1x2 Quadrangle, south-central Idaho was compiled by Ron Worl and Kate Johnson in 1995. The plate was compiled on a 1:250,000 scale topographic base map. TechniGraphic System, Inc. of Fort Collins Colorado digitized this map under contract for N.Shock. G.Green edited and prepared the digital version for publication as a geographic information system database. The digital geologic map database can be queried in many ways to produce a variety of geologic maps.

Signal digitizing system and method based on amplitude-to-time optical mapping

DOEpatents

Chou, Jason; Bennett, Corey V; Hernandez, Vince

2015-01-13

A signal digitizing system and method based on analog-to-time optical mapping, optically maps amplitude information of an analog signal of interest first into wavelength information using an amplitude tunable filter (ATF) to impress spectral changes induced by the amplitude of the analog signal onto a carrier signal, i.e. a train of optical pulses, and next from wavelength information to temporal information using a dispersive element so that temporal information representing the amplitude information is encoded in the time domain in the carrier signal. Optical-to-electrical conversion of the optical pulses into voltage waveforms and subsequently digitizing the voltage waveforms into a digital image enables the temporal information to be resolved and quantized in the time domain. The digital image may them be digital signal processed to digitally reconstruct the analog signal based on the temporal information with high fidelity.

Quaternary Geology and Liquefaction Susceptibility, San Francisco, California 1:100,000 Quadrangle: A Digital Database

USGS Publications Warehouse

Knudsen, Keith L.; Noller, Jay S.; Sowers, Janet M.; Lettis, William R.

1997-01-01

This Open-File report is a digital geologic map database. This pamphlet serves to introduce and describe the digital data. There are no paper maps included in the Open-File report. The report does include, however, PostScript plot files containing the images of the geologic map sheets with explanations, as well as the accompanying text describing the geology of the area. For those interested in a paper plot of information contained in the database or in obtaining the PostScript plot files, please see the section entitled 'For Those Who Aren't Familiar With Digital Geologic Map Databases' below. This digital map database, compiled from previously unpublished data, and new mapping by the authors, represents the general distribution of surficial deposits in the San Francisco bay region. Together with the accompanying text file (sf_geo.txt or sf_geo.pdf), it provides current information on Quaternary geology and liquefaction susceptibility of the San Francisco, California, 1:100,000 quadrangle. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:100,000 or smaller. The content and character of the database, as well as three methods of obtaining the database, are described below.

Digital soil map of the Ussuri River basin

NASA Astrophysics Data System (ADS)

Bugaets, A. N.; Pschenichnikova, N. F.; Tereshkina, A. A.; Krasnopeev, S. M.; Gartsman, B. I.; Golodnaya, O. M.; Oznobikhin, V. I.

2017-08-01

On the basis of digital soil, topographic, and geological maps; raster topography model; forestry materials; and literature data, the digital soil map of the Ussuri River basin (24400 km2) was created on a scale of 1: 100000. To digitize the initial paper-based maps and analyze the results, an ESRI ArcGIS Desktop (ArcEditor) v.10.1 (http://www.esri.com) and an open-code SAGA GIS v.2.3 (System for Automated Geoscientific Analyses, http://www.saga-gis.org) were used. The spatial distribution of soil areas on the obtained digital soil map is in agreement with modern cartographic data and the SRTM digital elevation model (SRTM DEM). The regional soil classification developed by G.I. Ivanov was used in the legend to the soil map. The names of soil units were also correlated with the names suggested in the modern Russian soil classification system. The major soil units on the map are at the soil subtypes that reflect the entire vertical spectrum of soils in the south of the Far East of Russia (Primorye region). These are mountainous tundra soils, podzolic soils, brown taiga soils, mountainous brown forest soils, bleached brown soils, meadow-brown soils, meadow gley soils, and floodplain soils). With the help of the spatial analysis function of GIS, the comparison of the particular characteristics of the soil cover with numerical characteristics of the topography, geological composition of catchments, and vegetation cover was performed.

Watershed boundaries and digital elevation model of Oklahoma derived from 1:100,000-scale digital topographic maps

USGS Publications Warehouse

Cederstrand, J.R.; Rea, A.H.

1995-01-01

This document provides a general description of the procedures used to develop the data sets included on this compact disc. This compact disc contains watershed boundaries for Oklahoma, a digital elevation model, and other data sets derived from the digital elevation model. The digital elevation model was produced using the ANUDEM software package, written by Michael Hutchinson and licensed from the Centre for Resource and Environmental Studies at The Australian National University. Elevation data (hypsography) and streams (hydrography) from digital versions of the U.S. Geological Survey 1:100,000-scale topographic maps were used by the ANUDEM package to produce a hydrologically conditioned digital elevation model with a 60-meter cell size. This digital elevation model is well suited for drainage-basin delineation using automated techniques. Additional data sets include flow-direction, flow-accumulation, and shaded-relief grids, all derived from the digital elevation model, and the hydrography data set used in producing the digital elevation model. The watershed boundaries derived from the digital elevation model have been edited to be consistent with contours and streams from the U.S. Geological Survey 1:100,000-scale topographic maps. The watershed data set includes boundaries for 11-digit Hydrologic Unit Codes (watersheds) within Oklahoma, and 8-digit Hydrologic Unit Codes (cataloging units) outside Oklahoma. Cataloging-unit boundaries based on 1:250,000-scale maps outside Oklahoma for the Arkansas, Red, and White River basins are included. The other data sets cover Oklahoma, and where available, portions of 1:100,000-scale quadrangles adjoining Oklahoma.

Geomorphological Map of the South Belet Region of Titan: An Exploration of Mid-Latitude-to-Pole Transition Zones

NASA Astrophysics Data System (ADS)

Schoenfeld, A.; Lopes, R.; Malaska, M.; Solomonidou, A.

2017-12-01

We carried out detailed geomorphological mapping of Titan's mid-latitude region south of the Belet Sand Sea. We used radar data collected by Cassini's Synthetic Aperture Radar (SAR) as our basemap, supplemented by images from VIMS, ISS, SARtopo, and microwave emissivity datasets. We mapped at a scale of 1:800,000 in all areas of the South Belet region covered by SAR swaths, taking into consideration the 300 m/pixel resolution of the swaths. For the mid-latitudes, we have defined five broad classes of terrains following Malaska et al. (2015). These terrain classes are craters, hummocky/mountainous, labyrinth, plains, and dunes. We have found that the hummocky/mountainous terrains are the oldest, with a radiometric signature consistent with icy materials. Dunes are the youngest units and return a radiometric signature consistent with organic sediments. We find that the South Belet region is covered primarily by the dune and plain units typical of Titan's mid-latitudes (Malaska et al. 2015). Previous mapping efforts of the mid-latitude regions of Titan (Lopes et al. 2016; Malaska et al. 2015) have indicated that these regions are predominately modified and influenced by aeolian activities. A plains unit designated "scalloped plains" is prominently featured between the 50°S and 60°S latitudes of this region. In this area we also find a terrain unit designated "dark irregular plains" that has been interpreted as damp materials saturated with liquid hydrocarbons (Malaska et al 2015; Hayes et al. 2008). We also note a higher occurrence of fluvial channels starting at this latitude zone and extending poleward. We suggest that these features demark the transition zone between mid-latitude/equatorial aeolian-dominated processes and fluvial-dominated processes prevailing at the poles.

Digital database of the geologic map of the island of Hawai'i [Hawaii

USGS Publications Warehouse

Trusdell, Frank A.; Wolfe, Edward W.; Morris, Jean

2006-01-01

This online publication (DS 144) provides the digital database for the printed map by Edward W. Wolfe and Jean Morris (I-2524-A; 1996). This digital database contains all the information used to publish U.S. Geological Survey Geologic Investigations Series I-2524-A (available only in paper form; see http://pubs.er.usgs.gov/pubs/i/i2524A). The database contains the distribution and relationships of volcanic and surficial-sedimentary deposits on the island of Hawai‘i. This dataset represents the geologic history for the five volcanoes that comprise the Island of Hawai'i. The volcanoes are Kohala, Mauna Kea, Hualalai, Mauna Loa and Kīlauea.This database of the geologic map contributes to understanding the geologic history of the Island of Hawai‘i and provides the basis for understanding long-term volcanic processes in an intra-plate ocean island volcanic system. In addition the database also serves as a basis for producing volcanic hazards assessment for the island of Hawai‘i. Furthermore it serves as a base layer to be used for interdisciplinary research.This online publication consists of a digital database of the geologic map, an explanatory pamphlet, description of map units, correlation of map units diagram, and images for plotting. Geologic mapping was compiled at a scale of 1:100,000 for the entire mapping area. The geologic mapping was compiled as a digital geologic database in ArcInfo GIS format.

DEVELOPMENT OF LAND COVER AND TERRAIN DATA BASES FOR THE INNOKO NATIONAL WILDLIFE REFUGE, ALASKA, USING LANDSAT AND DIGITAL TERRAIN DATA.

USGS Publications Warehouse

Markon, Carl J.; Talbot, Stephen

1986-01-01

Landsat-derived land cover maps and associated elevation, slope, and aspect class maps were produced for the Innoko National Wildlife Refuge (3,850,000 acres; 1,555,095 hectares) in northwestern Alaska. These maps and associated digital data products are being used by the U. S. Fish and Wildlife Service for wildlife management, research, and comprehensive conservation planning. Portions of two Landsat Multispectral Scanner (MSS) scenes and digital terrain data were used to produce 1:250,000 scale land cover and terrain maps. Prints of summer and winter Landsat MSS scenes were used to manually interpret broad physiographic strata. These strata were transferred to U. S. Geological Survey 1:250,000-scale topographic maps and digitized. Seven major land cover classes and 23 subclasses were identified. The major land cover classes include: forest, scrub, dwarf scrub and related types, herbaceous, scarcely vegetated areas, water, and shadow.

3D silicon breast surface mapping via structured light profilometry

NASA Astrophysics Data System (ADS)

Vairavan, R.; Ong, N. R.; Sauli, Z.; Kirtsaeng, S.; Sakuntasathien, S.; Shahimin, M. M.; Alcain, J. B.; Lai, S. L.; Paitong, P.; Retnasamy, V.

2017-09-01

Digital fringe projection technique is one of the promising optical methods for 3D surface imaging as it demonstrates non contact and non invasive characteristics. The potential of this technique matches the requirement for human body evaluation, as it is vital for disease diagnosis and for treatment option selection. Thus, the digital fringe projection has addressed this requirement with its wide clinical related application and studies. However, the application of this technique for 3D surface mapping of the breast is very minimal. Hence, in this work, the application of digital fringe projection for 3D breast surface mapping is reported. Phase shift fringe projection technique was utilized to perform the 3D breast surface mapping. Maiden results have confirmed the feasibility of using the digital fringe projection method for 3D surface mapping of the breast and it can be extended for breast cancer detection.

Method for the visualization of landform by mapping using low altitude UAV application

NASA Astrophysics Data System (ADS)

Sharan Kumar, N.; Ashraf Mohamad Ismail, Mohd; Sukor, Nur Sabahiah Abdul; Cheang, William

2018-05-01

Unmanned Aerial Vehicle (UAV) and Digital Photogrammetry are evolving drastically in mapping technology. The significance and necessity for digital landform mapping are developing with years. In this study, a mapping workflow is applied to obtain two different input data sets which are the orthophoto and DSM. A fine flying technology is used to capture Low Altitude Aerial Photography (LAAP). Low altitude UAV (Drone) with the fixed advanced camera was utilized for imagery while computerized photogrammetry handling using Photo Scan was applied for cartographic information accumulation. The data processing through photogrammetry and orthomosaic processes is the main applications. High imagery quality is essential for the effectiveness and nature of normal mapping output such as 3D model, Digital Elevation Model (DEM), Digital Surface Model (DSM) and Ortho Images. The exactitude of Ground Control Points (GCP), flight altitude and the resolution of the camera are essential for good quality DEM and Orthophoto.

Digital Soil Mapping – A platform for enhancing soil learning.

USDA-ARS?s Scientific Manuscript database

The expansion of digital infrastructure and tools has generated massive data and information as well as a need for reliable processing and accurate interpretations. Digital Soil Mapping is no exception in that it has provided opportunities for professionals and the public to interact at field and tr...

Geologic Communications | Alaska Division of Geological & Geophysical

Science.gov Websites

improves a database for the Division's digital and map-based geological, geophysical, and geochemical data interfaces DGGS metadata and digital data distribution - Geospatial datasets published by DGGS are designed to be compatible with a broad variety of digital mapping software, to present DGGS's geospatial data

Application of Ifsar Technology in Topographic Mapping: JUPEM's Experience

NASA Astrophysics Data System (ADS)

Zakaria, Ahamad

2018-05-01

The application of Interferometric Synthetic Aperture Radar (IFSAR) in topographic mapping has increased during the past decades. This is due to the advantages that IFSAR technology offers in solving data acquisition problems in tropical regions. Unlike aerial photography, radar technology offers wave penetration through cloud cover, fog and haze. As a consequence, images can be made free of any natural phenomenon defects. In Malaysia, Department of Survey and Mapping Malaysia (JUPEM) has been utilizing the IFSAR products since 2009 to update topographic maps at 1 : 50,000 map scales. Orthorectified radar imagery (ORI), Digital Surface Models (DSM) and Digital Terrain Models (DTM) procured under the project have been further processed before the products are ingested into a revamped mapping workflow consisting of stereo and mono digitizing processes. The paper will highlight the experience of Department of Survey and Mapping Malaysia (DSMM)/ JUPEM in using such technology in order to speed up mapping production.

Standard for the U.S. Geological Survey Historical Topographic Map Collection

USGS Publications Warehouse

Allord, Gregory J.; Fishburn, Kristin A.; Walter, Jennifer L.

2014-01-01

This document defines the digital map product of the U.S. Geological Survey (USGS) Historical Topographic Map Collection (HTMC). The HTMC is a digital archive of about 190,000 printed topographic quadrangle maps published by the USGS from the inception of the topographic mapping program in 1884 until the last paper topographic map using lithographic printing technology was published in 2006. The HTMC provides a comprehensive digital repository of all scales and all editions of USGS printed topographic maps that is easily discovered, browsed, and downloaded by the public at no cost. Each printed topographic map is scanned “as is” and captures the content and condition of each map. The HTMC provides ready access to maps that are no longer available for distribution in print. A new generation of topographic maps called “US Topo” was defined in 2009. US Topo maps, though modeled on the legacy 7.5-minute topographic maps, conform to different standards. For more information on the HTMC, see the project Web site at: http://nationalmap.gov/historical/.

Topographic map of the western region of Dao Vallis in Hellas Planitia, Mars; MTM 500k -40/082E OMKT

USGS Publications Warehouse

Rosiek, Mark R.; Redding, Bonnie L.; Galuszka, Donna M.

2006-01-01

This map, compiled photogrammetrically from Viking Orbiter stereo image pairs, is part of a series of topographic maps of areas of special scientific interest on Mars. Contours were derived from a digital terrain model (DTM) compiled on a digital photogrammetric workstation using Viking Orbiter stereo image pairs with orientation parameters derived from an analytic aerotriangulation. The image base for this map employs Viking Orbiter images from orbits 406 and 363. An orthophotomosaic was created on the digital photogrammetric workstation using the DTM compiled from stereo models.

Digital recovery, modification, and analysis of Tetra Tech seismic horizon mapping, National Petroleum Reserve Alaska (NPRA), northern Alaska

USGS Publications Warehouse

Saltus, R.W.; Kulander, Christopher S.; Potter, Christopher J.

2002-01-01

We have digitized, modified, and analyzed seismic interpretation maps of 12 subsurface stratigraphic horizons spanning portions of the National Petroleum Reserve in Alaska (NPRA). These original maps were prepared by Tetra Tech, Inc., based on about 15,000 miles of seismic data collected from 1974 to 1981. We have also digitized interpreted faults and seismic velocities from Tetra Tech maps. The seismic surfaces were digitized as two-way travel time horizons and converted to depth using Tetra Tech seismic velocities. The depth surfaces were then modified by long-wavelength corrections based on recent USGS seismic re-interpretation along regional seismic lines. We have developed and executed an algorithm to identify and calculate statistics on the area, volume, height, and depth of closed structures based on these seismic horizons. These closure statistics are tabulated and have been used as input to oil and gas assessment calculations for the region. Directories accompanying this report contain basic digitized data, processed data, maps, tabulations of closure statistics, and software relating to this project.

Digital terrain modeling and industrial surface metrology: Converging realms

USGS Publications Warehouse

Pike, R.J.

2001-01-01

Digital terrain modeling has a micro-and nanoscale counterpart in surface metrology, the numerical characterization of industrial surfaces. Instrumentation in semiconductor manufacturing and other high-technology fields can now contour surface irregularities down to the atomic scale. Surface metrology has been revolutionized by its ability to manipulate square-grid height matrices that are analogous to the digital elevation models (DEMs) used in physical geography. Because the shaping of industrial surfaces is a spatial process, the same concepts of analytical cartography that represent ground-surface form in geography evolved independently in metrology: The surface topography of manufactured components, exemplified here by automobile-engine cylinders, is routinely modeled by variogram analysis, relief shading, and most other techniques of parameterization and visualization familiar to geography. This article introduces industrial surface-metrology, examines the field in the context of terrain modeling and geomorphology and notes their similarities and differences, and raises theoretical issues to be addressed in progressing toward a unified practice of surface morphometry.

Ecoregions and ecodistricts: Ecological regionalizations for the Netherlands' environmental policy

NASA Astrophysics Data System (ADS)

Klijn, Frans; de Waal, Rein W.; Oude Voshaar, Jan H.

1995-11-01

For communicating data on the state of the environment to policy makers, various integrative frameworks are used, including regional integration. For this kind of integration we have developed two related ecological regionalizations, ecoregions and ecodistricts, which are two levels in a series of classifications for hierarchically nested ecosystems at different spatial scale levels. We explain the compilation of the maps from existing geographical data, demonstrating the relatively holistic, a priori integrated approach. The resulting maps are submitted to discriminant analysis to test the consistancy of the use of mapping characteristics, using data on individual abiotic ecosystem components from a national database on a 1-km2 grid. This reveals that the spatial patterns of soil, groundwater, and geomorphology correspond with the ecoregion and ecodistrict maps. Differences between the original maps and maps formed by automatically reclassifying 1-km2 cells with these discriminant components are found to be few. These differences are discussed against the background of the principal dilemma between deductive, a priori integrated, and inductive, a posteriori, classification.

Geologic Map of the Pueblo of Isleta Tribal Lands and Vicinity, Bernalillo, Torrance, and Valencia Counties, Central New Mexico

USGS Publications Warehouse

Maldonado, Florian; Slate, Janet L.; Love, Dave W.; Connell, Sean D.; Cole, James C.; Karlstrom, Karl E.

2007-01-01

This 1:50,000-scale map compiles geologic mapping of the Pueblo of Isleta tribal lands and vicinity in the central part of the Albuquerque Basin in central New Mexico. The map synthesizes new geologic mapping and summarizes the stratigraphy, structure, and geomorphology of an area of approximately 2,000 km2 that spans the late Paleogene-Neogene Rio Grande rift south of Albuquerque, N. Mex. The map is part of studies conducted between 1996 and 2001 under the U.S. Geological Survey (USGS) Middle Rio Grande Basin Study by geologists from the USGS, the New Mexico Bureau of Geology and Mineral Resources (NMBGMR), and the University of New Mexico (UNM). This work was conducted in order to investigate the geologic factors that influence ground-water resources of the Middle Rio Grande Basin, and to provide new insights into the complex geologic history of the Rio Grande rift in this region.

Ocena georóżnorodności jako metoda określania potencjału geoturystycznego obszaru / Assessment of geodiversity as a method of geotourism potential assessment

NASA Astrophysics Data System (ADS)

Radwanek-Bąk, Barbara; Laskowicz, Izabela

2012-12-01

The aim of the presented paper was to assess the geodiversity in the aspect of a geotourist potential by using modern GIS tools. The study area was Szczawnica region with known high nature and landscape values, interesting geology, geomorphology, as well as one of famous Polish health resorts. The analysis was made by overlapping method, basing on several thematic sheets creating the main criteria of assessment: lithostratigraphy, geomorphology, waters. Main criteria were divided into detailed ones like: the number of units, number of different types of units, land slope, length of watercourse, number of springs. The assessment itself was made by simply quality classification. The final map of the geodiversity assessment allows to show the most diverse and most interesting areas. Such zones are preferable to find some geotopes and geotourist attractions inside them to expose and explain the geodiversity.

Railway deformation detected by DInSAR over active sinkholes in the Ebro Valley evaporite karst, Spain

NASA Astrophysics Data System (ADS)

Galve, J. P.; Castañeda, C.; Gutiérrez, F.

2015-11-01

Subsidence was measured for the first time on railway tracks in the central sector of Ebro Valley (NE Spain) using Differential Synthetic Aperture Radar Interferometry (DInSAR) techniques. This area is affected by evaporite karst and the analysed railway corridors traverse active sinkholes that produce deformations in these infrastructures. One of the railway tracks affected by slight settlements is the Madrid-Barcelona high-speed line, a form of transport infrastructure highly vulnerable to ground deformation processes. Our analysis based on DInSAR measurements and geomorphological surveys indicates that this line shows dissolution-induced subsidence and compaction of anthropogenic deposits (infills and embankments). Significant sinkhole-related subsidence was also measured by DInSAR techniques on the Castejón-Zaragoza conventional railway line. This study demonstrates that DInSAR velocity maps, coupled with detailed geomorphological surveys, may help in the identification of the railway track sections that are affected by active subsidence.

Chirp subbottom profile data collected in 2015 from the northern Chandeleur Islands, Louisiana

USGS Publications Warehouse

Forde, Arnell S.; DeWitt, Nancy T.; Fredericks, Jake J.; Miselis, Jennifer L.

2018-01-30

As part of the Barrier Island Evolution Research project, scientists from the U.S. Geological Survey (USGS) St. Petersburg Coastal and Marine Science Center conducted a nearshore geophysical survey around the northern Chandeleur Islands, Louisiana, in September 2015. The objective of the project is to improve the understanding of barrier island geomorphic evolution, particularly storm-related depositional and erosional processes that shape the islands over annual to interannual time scales (1–5 years). Collecting geophysical data can help researchers identify relations between the geologic history of the islands and their present day morphology and sediment distribution. High-resolution geophysical data collected along this rapidly changing barrier island system can provide a unique time-series dataset to further the analyses and geomorphological interpretations of this and other coastal systems, improving our understanding of coastal response and evolution over medium-term time scales (months to years). Subbottom profile data were collected in September 2015 offshore of the northern Chandeleur Islands, during USGS Field Activity Number 2015-331-FA. Data products, including raw digital chirp subbottom data, processed subbottom profile images, survey trackline map, navigation files, geographic information system data files and formal Federal Geographic Data Committee metadata, and Field Activity Collection System and operation logs are available for download.

Large-scale deep-water seafloor mapping from the Rockall to the Hatton basins, NE Atlantic

NASA Astrophysics Data System (ADS)

Monteys, X.; Thébaudeau, B.; Murcia, C.; Duncan, N.

2016-02-01

Multibeam data acquired in 2000 and 2001 during the Irish National Seabed Survey (INSS) are used for the first detailed investigation of the seabed geomorphology and sediment type in the Hatton-Rockall basin area of the North East Atlantic Ocean, covering an area of approximately 80,000 km². The original multibeam survey produced bathymetric and backscatter datasets that allowed the creation of a Digital Terrain Models of approximately 50 m in resolution in water depths between 500 and 3500 m. Near-surface sediments for the entire region haven been classified using features derived from multibeam angular backscatter data (12kHz) and robust unsupervised clustering techniques. Additionally, sub bottom data imaging the shallow stratigraphy and geomagnetic measurements collected at the time of the MBES survey are combined to further characterise some of the features identified. The features presented in detail include parts of the Hatton and Gardar contourite drifts, volcanic mounds identified by their morphology and magnetic signature, deep-water coral mounds, iceberg scours as well as canyons, gullies and escarpments along and down the slopes of the banks and mounds. This study highlights for the first time the variety and complexity of the seafloor present at the seabed in the Irish Hatton-Rockall basin area

Mapping, Charting, and Geodesy Division Abstracts of Publications, Presentations and Transitions: 1991

DTIC Science & Technology

1992-05-01

Clark, T.H. Fay, Multispectral I Bathymetry Programs: A Users Guide, NTN 95. Myrick, S., M. Lohrenz, Data Base Design Document for the Digital Map...Computer1 Software in the A-12 Digital Map Set, NTN 162. Myrick, S., M. Lohrenz, P. Wischow, M. Trenchard, S. Tyskiewicz, J. Kaufman, MDFF I HELP...Shaw, K, D. Byman, S. Carter, M. Kalcic, M. Clawson, M. Harris, A Summary of the i Collected Data from a Survey of Navy Digital MC&G Requirements

Keeping Pace with Climate Change: Habitat Protection in the Face of Uncertainty

NASA Astrophysics Data System (ADS)

Flitcroft, R. L.; Burnett, K.; Giannico, G.

2014-12-01

Estuaries provide critical habitat for many economically and culturally important species. In the Pacific Northwest, intertidal and subtidal areas provide critical habitat for production of native and commercial oysters (Olympia oyster Ostrea lurida and Pacific oyster Crassostrea gigas, respectively) that in turn provide refuge and rearing habitat for Dungeness Crab, Metacarcinus magister. Environments ranging from subtidal through freshwater zones provide nursery areas for juvenile salmonids at different development stages in their life history. Most Oregon estuaries have been significantly altered by humans over the past century, reducing the quantity and diversity of available habitats. Management agencies have responded with projects to restore and enhance estuarine habitats. Unfortunately, future climate change and sea-level rise could render many current restoration projects ineffective over time. Planning for habitat restoration that keeps pace with climate change will be critical to the sustainable production of seafood and maintenance of ecosystem function. However, land managers and citizens lack the spatially-explicit data needed to incorporate the potential effects of climate change and sea-level rise into planning for habitat improvement projects in estuarine areas. To meet this need, we developed simple models using LiDAR to characterize the geomorphologies of multiple Oregon estuaries. We were able to map the margin of current mean high tide, and contour intervals associated with different potential increases in mean high tide. Because our analysis relied on digital data, we compared three types of digital data in one estuary to assess the utility of different data sets in predicting changes in estuary shape. For each estuary, we assessed changes in the amount and complexity of edge habitats. The simple modeling approach we applied can also be used to identify areas that may be most amenable to pre-emptive restoration actions to mitigate or enhance habitats under future climatic conditions.

The use of karst geomorphology for planning, hazard avoidance and development in Great Britain

NASA Astrophysics Data System (ADS)

Cooper, Anthony H.; Farrant, Andrew R.; Price, Simon J.

2011-11-01

Within Great Britain five main types of karstic rocks - dolomite, limestone, chalk, gypsum and salt - are present. Each presents a different type and severity of karstic geohazard which are related to the rock solubility and geological setting. Typical karstic features associated with these rocks have been databased by the British Geological Survey (BGS) with records of sinkholes, cave entrances, stream sinks, resurgences and building damage; data for more than half of the country has been gathered. BGS has manipulated digital map data, for bedrock and superficial deposits, with digital elevation slope models, superficial deposit thickness models, the karst data and expertly interpreted areas, to generate a derived dataset assessing the likelihood of subsidence due to karst collapse. This dataset is informed and verified by the karst database and marketed as part of the BGS GeoSure suite. It is currently used by environmental regulators, the insurance and construction industries, and the BGS semi-automated enquiry system. The database and derived datasets can be further combined and manipulated using GIS to provide other datasets that deal with specific problems. Sustainable drainage systems, some of which use soak-aways into the ground, are being encouraged in Great Britain, but in karst areas they can cause ground stability problems. Similarly, open loop ground source heat or cooling pump systems may induce subsidence if installed in certain types of karstic environments such as in chalk with overlying sand deposits. Groundwater abstraction also has the potential to trigger subsidence in karst areas. GIS manipulation of the karst information is allowing Great Britain to be zoned into areas suitable, or unsuitable, for such uses; it has the potential to become part of a suite of planning management tools for local and National Government to assess the long term sustainable use of the ground.

Spatial distribution of erosion and deposition during a glacier surge: Brúarjökull, Iceland

NASA Astrophysics Data System (ADS)

Korsgaard, Niels J.; Schomacker, Anders; Benediktsson, Ívar Örn; Larsen, Nicolaj K.; Ingólfsson, Ólafur; Kjær, Kurt H.

2015-12-01

Time-series of digital elevation models (DEMs) of the forefield of the Brúarjökull surge-type glacier in Iceland were used to quantify the volume of material that was mobilized by the 1963-1964 surge. The DEMs were produced by stereophotogrammetry on aerial photographs from before the surge (1961) and after (1988 and 2003). The analysis was performed on two DEMs of Difference (DoDs), i.e., a 1961-2003 DoD documenting the impact of the surge and a 1988-2003 DoD documenting the post-surge modification of the juvenile surging glacier landsystem. Combined with a digital geomorphological map, the DoDs allow us to quantify the impact of the surge on a landsystem scale down to individual landforms. A total of 34.2 ± 11.3 × 106 m3 of material was mobilized in the 30.7-km2 study area as a result of the most recent surge event. Of these, 17.4 ± 6.6 × 106 m3 of the material were eroded and 16.8 ± 4.7 × 106 m3 were deposited. More than half of the deposited volume was ice-cored landforms. This study demonstrates that although the total mobilized mass volume is high, the net volume gain of ice and sediment deposited as landforms in the forefield caused by the surge is low. Furthermore, deposition of new dead-ice from the 1963-1964 surge constitutes as much as 64% of the volume gain in the forefield. The 1988-2003 DoD is used to quantify the melt-out of this dead-ice and other paraglacial modification of the recently deglaciated forefield of Brúarjökull.

Eruptive Style and Geochronology of the Initial Fases of Monogenetic Vulcanism of Southern Basis of Mexico

NASA Astrophysics Data System (ADS)

Jaimes, M. D.; Martin, A.; Layer, P. W.

2013-05-01

Monogenetic vulcanism in the central part of Mexico includes the Chichinautzin Monogenetic Volcanic Field, located at the front of the Transmexican Volcanic Belt (TMVB), 300 km from the Mesoamerican trench. At least 220 volcanoes formed during the Pleistocene and Holocene. Most are scoria cones with associated lava flows, small shield volcanoes and lava domes; and cover an área of 2400 km2 (Martin Del Pozzo, 1982; Wallace and Carmichael, 1999; Velasco-Tapia and Verma, 2001; Velasco-Tapia, 2003). Previous studies in the area (paleomagnetic, geomorphologic, vulcanologic and radiometric) indicate that volcanism is less than 0.79 Ma (Bloomfield, 1973; Mooser et al., 1974; Herrero and Pal, 1978; Martin Del Pozzo et al., 1997; Siebe et al., 2004a). Our field studies include mapping and sampling of 50 lava flows associated with scoria cones, phreatomagmatic structures (2), lava flows without cones (2) and lava domes (5). Geomorphologic analyses, whole rock chemical analyse (FRX), petrographic and geochronologic (Ar-Ar) were carried out. We identified three zones with different eruptive styles: strombolian and violent strombolian to the north and south; and phreatomagmatic style only in the north. Samples are basaltic andesites to dacites. Geochronologic data is consistent with some of the relative ages according to the geomorphologic data and corresponds to three age groups.

Map of Nasca Geoglyphs

NASA Astrophysics Data System (ADS)

Hanzalová, K.; Pavelka, K.

2013-07-01

The Czech Technical University in Prague in the cooperation with the University of Applied Sciences in Dresden (Germany) work on the Nasca Project. The cooperation started in 2004 and much work has been done since then. All work is connected with Nasca lines in southern Peru. The Nasca project started in 1995 and its main target is documentation and conservation of the Nasca lines. Most of the project results are presented as WebGIS application via Internet. In the face of the impending destruction of the soil drawings, it is possible to preserve this world cultural heritage for the posterity at least in a digital form. Creating of Nasca lines map is very useful. The map is in a digital form and it is also available as a paper map. The map contains planimetric component of the map, map lettering and altimetry. Thematic folder in this map is a vector layer of the geoglyphs in Nasca/Peru. Basis for planimetry are georeferenced satellite images, altimetry is created from digital elevation model. This map was created in ArcGis software.

Surface expression of intraplate postglacial faults in Sweden: from LiDAR data

NASA Astrophysics Data System (ADS)

Abduljabbar, Mawaheb; Ask, Maria; Bauer, Tobias; Lund, Björn; Smith, Colby; Mikko, Henrik; Munier, Raymond

2016-04-01

Large intraplate earthquakes, up to magnitude 8.0±0.3 (Lindblom et al. 2015) are inferred to have occurred in northern Fennoscandia at the end of, or just after the Weichselian deglaciation. More than a dozen large so-called postglacial faults (PGF) have been found in the region. The present-day microseismic activity is rather high in north Sweden, and there is a correlation between microseismicity and mapped PGF scarps: 71% of the observed earthquakes north of 66°N locate within 30 km to the southeast and 10 km to the northwest of PGFs (Lindblom et al., 2015). Surface expressions of PGFs in Sweden have mainly been mapped using aerial photogrammetry and trenching (e.g. Lagerbäck & Sundh 2008). Their detailed surface geometry may be investigated using the new high-resolution elevation model of Sweden (NNH) that has a vertical- and lateral resolution of 2 m and 0.25 m, respectively. With NNH data, known PGFs have been modified, and a number of new potential PGFs have been identified (Smith et al. 2014; Mikko et al. 2015). However, the detailed variation of their surface expression remains to be determined. Our main objective is to constrain the strike and surface offset (i.e., apparent vertical throw because of soil cover overlays the bedrock) across the PGF scarps. We anticipate using the results to constrain direction of fault motion and paleomagnitudes of PGFs, and in numerical analyzes to investigate the nature of PGFs. We have developed a methodology for analyzing PGF-geomorphology from LiDAR data using two main software platforms (Ask et al. 2015): (1) Move2015 by Midland Valley has been used for constructing 3D models of the surface traces of the PGFs to determine apparent vertical throw. The apparent hanging- and footwall cut off lines are digitized, and subsequent computation of coordinates is rather time efficient and provide continuous data of fault and soil geomorphology that can be statistically analyzed; and (2) ArcGIS 10.3 by Esri has mostly been used to derive the slope model for the study area. We successfully tested the methodology within a limited area of the Pärvie fault zone, which is the longest known PGF in the world (Ask et al. 2015). Here, we apply the methodology to PGFs in northern Sweden. Additionally, we are planning to analyse PGFs within a virtual reality environment utilizing the GeoVisionary software platform by Virtalis Ltd. in order to increase accuracy and efficiency and to decrease modelling uncertainties. References Ask et al. 2015. Geomorphology of intraplate postglacial faults in Sweden. AGU, Abstract #83167 Lindblom, et al., 2015. Microearthquakes illuminate the deep structure of the endglacial Pärvie fault, northern Sweden. doi: 10.1093/gji/ggv112 Lagerbäck & Sundh, 2008. Early Holocene faulting and paleoseismicity in northern Sweden. http://resource.sgu.se/produkter/c/c836-rapport.pdf Mikko, et al. 2015. LiDAR-derived inventory of post-glacial fault scarps in Sweden. doi:10.1080/11035897.2015.1036360 Smith, et al., 2014. Surficial geology indicates early Holocene faulting and seismicity, central Sweden. doi: 10.1007/s00531-014-1025-6

The MeTIBas project: an example of settlement continuity in a coastal changing landscape of southern Italy

NASA Astrophysics Data System (ADS)

Bavusi, Massimo; Di Leo, Paola; Giammatteo, Tonia; Gioia, Dario; Schiattarella, Marcello

2016-04-01

The MeTIBas (Italian acronym for Innovative Methods and Technologies for the Cultural Heritage in the Basilicata region) project aims to develop an innovative geoarchaeological investigation approach for large areas. Analyses of environmental dynamics, palaeoclimatic proxies, spatial and temporal evolution of settlements and, more in general, of the relationships between man and landscape have been carried also through the implementation of a Territorial Information System, drawing-up of an experimental digital geoarchaeological map, and creation of an open geoarchaeological database. The project methods have been applied in the coastal area of Metaponto, which roughly coincides with the ancient territory of the Greek settlement of Metapontum and its chora and includes a region of about 400 sq. km in the Ionian sector of the Basilicata region, southern Italy. The backshore area of the Metaponto coastal plain was characterized by the presence of wide limno-palustrine environments, reclaimed during the first decades of the last century. Geomorphological mapping, GIS-supported statistics, and analysis of the topographic features of the landforms represent the key to extract the settlement rules and the site dynamics of the study area. Site distribution and relationships with landscape elements allow us to investigate the settlement patterns and human activities and choices. A wide archive of archaeological data on the whole study area - from Prehistoric times to Roman age - has been therefore used to connect the wandering or persistence of the ancient sites in relation with different landforms and their changes during the last 5000 years. The layout of the site arrangement clearly traces the main geomorphological features of the area (i.e. settlements along fluvial scarps, sites on the flat surfaces of marine and fluvial terraces, main villages in the coastal plain). From a chronological viewpoint, after a progressive increase of the settlements and other archaeological elements - sometimes with changes in their function - the human presence becomes dramatically strong during the Greek colonization and the Roman period. Only few archaeological typologies remain the same through time, as for example the farms and their associated features, whilst several sites assume different intended use. From classical to Hellenistic time span, a significant increase of sites can be observed in both the coastal plain and in the intermediate orders of marine terraces, whose top surfaces range from 45 m to 110 m a.s.l.: this could mean that the pre-existing environmental setting of the coastal plain was preserved (i.e. no diffused presence of marshes and swamps) and the plain was not abandoned, but at the same time the terraced surfaces offered similar or better conditions for agricultural practices. From Hellenistic to Roman times, a dramatic collapse of the stable human presence occurred, probably due to historical causes coupled with a landscape deterioration (maybe linked to an increase in flooding occurrence in the coastal plain and in the floodplains of the lower reaches of the main rivers). Results indicate that an intrinsic geomorphological fragility of the territory has accompanied the strong agricultural vocation of the study area, persisting until now.

The French Atlantic Littoral and the Massif Armoricain. [Bay of Biscay, France and Spain

NASA Technical Reports Server (NTRS)

Verger, F. (Principal Investigator); Monget, J. M.; Scanvic, J. Y.

1976-01-01

The author has identified the following significant results. Diachronic use of LANDSAT data time series will in time allow study of statistically submerged frequencies in tidal areas. This is an essential element of coastal geomorphology and of coastal zone management, being particularly useful in siting shellfish farms. Maps at useable scales and simple user oriented legends should become an essential document for coastal planning agencies.

Fuzzy logic-based assessment for mapping potential infiltration areas in low-gradient watersheds.

PubMed

Quiroz Londoño, Orlando Mauricio; Romanelli, Asunción; Lima, María Lourdes; Massone, Héctor Enrique; Martínez, Daniel Emilio

2016-07-01

This paper gives an account of the design a logic-based approach for identifying potential infiltration areas in low-gradient watersheds based on remote sensing data. This methodological framework is applied in a sector of the Pampa Plain, Argentina, which has high level of agricultural activities and large demands for groundwater supplies. Potential infiltration sites are assessed as a function of two primary topics: hydrologic and soil conditions. This model shows the state of each evaluated subwatershed respecting to its potential contribution to infiltration mainly based on easily measurable and commonly used parameters: drainage density, geomorphologic units, soil media, land-cover, slope and aspect (slope orientation). Mapped outputs from the logic model displayed 42% very low-low, 16% moderate, 41% high-very high contribution to potential infiltration in the whole watershed. Subwatersheds in the upper and lower section were identified as areas with high to very high potential infiltration according to the following media features: low drainage density (<1.5 km/km(2)), arable land and pastures as the main land-cover categories, sandy clay loam to loam - clay loam soils and with the geomorphological units named poorly drained plain, channelized drainage plain and, dunes and beaches. Copyright © 2016 Elsevier Ltd. All rights reserved.

Geomorphology and Depositional Subenvironments of Gulf Islands National Seashore, Mississippi

USGS Publications Warehouse

Morton, Robert A.; Rogers, Bryan E.

2010-01-01

The U.S. Geological Survey (USGS) is studying coastal hazards and coastal change to improve our understanding of coastal ecosystems and to develop better capabilities of predicting future coastal change. One approach to understanding the dynamics of coastal systems is to monitor changes in barrier-island subenvironments through time. This involves examining morphological and topographic change at temporal scales ranging from millennia to years and spatial scales ranging from tens of kilometers to meters. Of particular interest are the processes that produce those changes and the determination of whether or not those processes are likely to persist into the future. In these analyses of hazards and change, both natural and anthropogenic influences are considered. Quantifying past magnitudes and rates of coastal change and knowing the principal factors that govern those changes are critical to predicting what changes are likely to occur under different scenarios, such as short-term impacts of extreme storms or long-term impacts of sea-level rise. Gulf Islands National Seashore was selected for detailed mapping of barrier-island morphology and topography because the islands offer a diversity of depositional subenvironments and the islands' areas and positions have changed substantially in historical time. The geomorphologic and subenvironmental maps emphasize the processes that formed the surficial features and also serve as a basis for documenting which subenvironments are relatively stable, such as the beach ridge complex, and those which are highly dynamic, such as the beach and active overwash zones. The primary mapping procedures used supervised functions within a Geographic Information System (GIS) that classified depositional subenvironments and features (map units) and delineated boundaries of the features (shapefiles). The GIS classified units on the basis of tonal patterns of a feature in contrast to adjacent features observed on georeferenced aerial photographs. Land elevations from recent lidar surveys served as supplementary data to assist in delineating the map-unit boundaries.

Remote sensing applied to geological mapping; comparative geomorphology and identification of mineral zones of zinc and lead in the region of Vazante, MG. [Brazil

NASA Technical Reports Server (NTRS)

Nascimento, F. S. D. (Principal Investigator); Nascimento, M. A. L. S. D.

1977-01-01

The author has identified the following significant results. Results showed that the black and white aerial photographs and the color infrared transparencies were efficient for mapping of three lithological units of the Paraopeba formation and for mineralized zones identification, respectively. Multispectral transparencies of I2S made it easier to separate dolomites, which were the rocks conditioning zinc and lead mineralization. Statistical analysis of morphometric indexes obtained from black and white photographs and topographic charts showed significant difference among three lithological units of Paraopeba formation which can be defined as Crest, Hilly, and Karstic reliefs.

Fire Island National Seashore

USGS Publications Warehouse

Brock, John C.; Wright, C. Wayne; Patterson, Matt; Nayagandhi, Amar; Patterson, Judd

2007-01-01

These lidar-derived topographic maps were produced as a collaborative effort between the U.S. Geological Survey (USGS) Coastal and Marine Geology Program, the National Park Service (NPS), Northeast Coastal and Barrier Network, Inventory and Monitoring Program, and the National Aeronautics and Space Administration (NASA) Wallops Flight Facility. The aims of the partnership that created this product are to develop advanced survey techniques for mapping barrier island geomorphology and habitats, and to enable the monitoring of ecological and geological change within National Seashores. This product is based on data from an innovative airborne lidar instrument under development at the NASA Wallops Flight Facility, the NASA Experimental Advanced Airborne Research Lidar (EAARL).

Integrated analysis of differential interferometric synthetic aperture radar (DInSAR) and geological data for measuring deformation movement of Kaligarang fault, Semarang-Indonesia

NASA Astrophysics Data System (ADS)

Prasetyo, Y.; Fakhrudin, Warasambi, S. M.

2016-05-01

Semarang is one of the densely populated city in Central Java which is has Kaligarang's fault. It is lie in Kaligarang River and across several dense urban settlement. The position of Kaligarang's river itself divides in the direction nearly north-south city of Semarang. The impact of the fault can be seen in severals indication such as a land subsidence phenomenon in Tinjomoyo village area which is make impact to house and road destruction. In this research, we have used combination methods between InSAR, DinSAR and geomorphology (geology data) where is this techniques used to identity the fault area and estimate Kaligarang's fault movement velocity. In fault movement velocity observation, we only compute the movement in vertical with neglect horizontal movement. The data used in this study of one pair ALOS PALSAR level 1.0 which was acquired on June 8, 2007and 10 of September 2009. Besides that third ALOS PALSAR earlier, also used data of SRTM DEM 4th version, is used for the correction of the topography. The use of the three methods already mentioned earlier have different functions. For the lnSAR method used for the establishment of a digital model in Semarang. After getting high models digital city of Semarang, the identification process can be done layout, length, width and area of the Kaligarang fault using geomorphology. Results of such identification can be calculated using the rate of deformation and fault movement. From the result generated DinSAR method of land subsidence rate between 3 em to II em. To know the truth measurement that used DinSAR method, is performed with the decline of validation that measured using GPS. After validating obtained standard deviation of 3,073 em. To estimate the Kaligarang's fault pattern and direction is using the geomorphology method. The results that Kaligarang's is an active fault that has fault strike slip as fault pattern. It makes this research is useful because could be used as an inquick assessment in fault identification and deformation movement observation.

Traces on the 'Ubaidian Shore: Mid-Holocene Eustasis, Marine Transgression, and Urbanization in the Mesopotamian Delta (Iraq)

NASA Astrophysics Data System (ADS)

Pournelle, J. R.; Smith, J. R.; Hritz, C.; Nsf Hrrpaa 1045974

2011-12-01

Development and flourit of pre-urban and urban complex societies of southern Mesopotamia (Iraq) during the mid-Holocene took place in the context of Tigris-Euphrates and Karun-Karkheh deltaic progradation on one hand, and marine transgression at the head of the Gulf on the other. Understanding these processes has profound implications for assessing likely resource bioavailability, resource extraction and transport options, population distribution and density, and labour requirements for intensification/ extensification of extraction and production activities during this critical formative period. Multiple attempts have been made to reconstruct the Gulf "shoreline" at various pre-historic and historical periods. Because no systematic coring operations have been undertaken in the region, these attempts have been hampered by the paucity of direct geologic evidence. Conflicting hypotheses based on models of deltaic subsidence, tectonic uplift, and and/or eustatic change were barely testable against scant available cores and archaeologically-derived proxies from a few sites on the western "shore," such as H3, Eridu, Ur, Uruk, and Tell al Oueli. Recently published coring operations in the Iranian Karun-Karkheh delta add considerably to the available corpus of archaeological and geomorphologic data useful for reconstructing the timeline and extent of these processes, especially on the eastern "shore," but these are also bounded in spatial and temporal extent. Multi-scale, multi-sensor processing of remote sensing data and imagery make possible a fuller interpretation of geomorphologic and artifactual evidence bearing on overall shoreline reconstruction from approximately 6,000-3,000 BCE. This paper reports the results of combining interpreted LANDSAT, ASTER, SPOT, CORONA, Digital Globe, and other imagery with multiple derived Digital Elevation Models, thus providing stochastic boundaries for re-interpreting geological and archaeological point data, as well as new pilot data collected in 2010-2011. The result is better understanding of the likely location, extent, and impact of maximum mid-Holocene marine incursion into lower Mesopotamia and Khuzistan associated with deltaic geomorphological and ecological evolution, with implications for assessing site locations, agricultural potential, and water transport routes available to the world's oldest-known cities.

Alaska Interim Land Cover Mapping Program; final report

USGS Publications Warehouse

Fitzpatrick-Lins, Katherine; Doughty, E.F.; Shasby, Mark; Benjamin, Susan

1989-01-01

In 1985, the U.S. Geological Survey initiated a research project to develop an interim land cover data base for Alaska as an alternative to the nationwide Land Use and Land Cover Mapping Program. The Alaska Interim Land Cover Mapping Program was subsequently created to develop methods for producing a series of land cover maps that utilized the existing Landsat digital land cover classifications produced by and for the major land management agencies for mapping the vegetation of Alaska. The program was successful in producing digital land cover classifications and statistical summaries using a common statewide classification and in reformatting these data to produce l:250,000-scale quadrangle-based maps directly from the Scitex laser plotter. A Federal and State agency review of these products found considerable user support for the maps. Presently the Geological Survey is committed to digital processing of six to eight quadrangles each year.

Karst map of Puerto Rico

USGS Publications Warehouse

Alemán González, Wilma B.

2010-01-01

This map is a digital compilation, combining the mapping of earlier geologists. Their work, cited on the map, contains more detailed descriptions of karst areas and landforms in Puerto Rico. This map is the basis for the Puerto Rico part of a new national karst map currently being compiled by the U.S. Geological Survey. In addition, this product is a standalone, citable source of digital karst data for Puerto Rico. Nearly 25 percent of the United States is underlain by karst terrain, and a large part of that area is undergoing urban and industrial development. Accurate delineations of karstic rocks are needed at scales suitable for national, State, and local maps. The data on this map contribute to a better understanding of subsidence hazards, groundwater contamination potential, and cave resources as well as serve as a guide to topical research on karst. Because the karst data were digitized from maps having a different scale and projection from those on the base map used for this publication, some karst features may not coincide perfectly with physiographic features portrayed on the base map.

Database for geologic maps of pyroclastic-flow and related deposits of the 1980 eruptions of Mount St. Helens, Washington

USGS Publications Warehouse

Furze, Andrew J.; Bard, Joseph A.; Robinson, Joel; Ramsey, David W.; Kuntz, Mel A.; Rowley, Peter D.; MacLeod, Norman S.

2017-10-31

This publication releases digital versions of the geologic maps in U.S. Geological Survey Miscellaneous Investigations Map 1950 (USGS I-1950), “Geologic maps of pyroclastic-flow and related deposits of the 1980 eruptions of Mount St. Helens, Washington” (Kuntz, Rowley, and MacLeod, 1990) (https://pubs.er.usgs.gov/publication/i1950). The 1980 Mount St. Helens eruptions on May 18, May 25, June 12, July 22, August 7, and October 16–18 produced pyroclastic-flow and related deposits. The distribution and morphology of these deposits, as determined from extensive field studies and examination of vertical aerial photographs, are shown on four maps in I-1950 (maps A–D) on two map sheets. Map A shows the May 18, May 25, and June 12 deposits; map B shows the July 22 deposits; map C shows the August 7 deposits; and map D shows the October 16–18 deposits. No digital geospatial versions of the geologic data were made available at the time of publication of the original maps. This data release consists of attributed vector features, data tables, and the cropped and georeferenced scans from which the features were digitized, in order to enable visualization and analysis of these data in GIS software. This data release enables users to digitally re-create the maps and description of map units of USGS I-1950; map sheet 1 includes text sections (Introduction, Physiography of Mount St. Helens at the time of the 1980 eruptions, Processes of the 1980 eruptions, Deposits of the 1980 eruptions, Limitations of the maps, Preparation of the maps, and References cited) and associated tables and figures that are not included in this data release.

USGS QA Plan: Certification of digital airborne mapping products

USGS Publications Warehouse

Christopherson, J.

2007-01-01

To facilitate acceptance of new digital technologies in aerial imaging and mapping, the US Geological Survey (USGS) and its partners have launched a Quality Assurance (QA) Plan for Digital Aerial Imagery. This should provide a foundation for the quality of digital aerial imagery and products. It introduces broader considerations regarding processes employed by aerial flyers in collecting, processing and delivering data, and provides training and information for US producers and users alike.

Geo-information for sustainable urban development of Greater Dhaka City, Bangladesh

NASA Astrophysics Data System (ADS)

Günther, Andreas; Asaduzzaman, Atm; Bahls, Rebecca; Ludwig, Rüdiger; Ashraful Kamal, Mohammad; Nahar Faruqa, Nurun

2015-04-01

Greater Dhaka City (including Dhaka and five adjacent municipal areas) is one of the fastest developing urban regions in the world. Densely build-up areas in the developed metropolitan area of Dhaka City are subject to extensive restructuring as common six-storied buildings are replaced by higher and heavier constructions. Additional stories are built on existing houses, frequently exceeding the allowable bearing pressure on the subsoil as supported by the foundations. In turn, newly developing areas are projected in marshy areas modified by extensive, largely unengineered landfills. In many areas, these terrains bear unfavorable building ground conditions, and reliable geospatial information is a major prerequisite for risk-sensitive urban planning. Within a collaborative technical cooperation project between Bangladesh and Germany, BGR supports GSB in the provision of geo-information for the Capital Development authority (RAJUK). For general urban planning, RAJUK successively develops a detailed area plan (DAP) at scale 1 : 50000 for the whole Greater Dhaka City area. Geospatial information have not been considered in the present DAP. Within the project, GSB prepared a detailed geomorphologic map matching the DAP both in areal extent and scale. The geomorphological setting can be used as an important spatial proxy for the characterization of the subsurface since highly segmented, elevated terraces consisting of consolidated sandy Pliocene deposits overlain by stiff Plio-Pleistocene sediments are sharply bordered by low lying-areas. The floodplain and marsh areas are consisting of thick, mechanically weak Holocene fluvial sandy-silty sediments that are sometimes alternated by organic layers. A first expert-based engineering geological reclassification of the geomorphological map resulting in five building ground suitability classes is highly supported by the spatial analysis of extensive archive borehole information consisting of depth-continuous standard penetration test (SPT) observations, engineering geological sample analyses and lithological profiles. The database compiled within the project currently contains more than 1600 locations. The joining of the spatial geomorphological information with the borehole data allows a specific characterization of the building ground classes in terms of bearing capacities for different foundation designs, earthquake-induced subsoil liquefaction potentials and depth-to-engineering rock head considerations. First-order hazard and cost scenarios for several general types of projected settlements can already be broadly evaluated with the data presented in a small scale (DAP scale). However, detailed building ground surveys have to be performed at larger spatial scales (1 : 10000 - 1 : 5000) in areas assigned for new settlements. These involve regular spaced borehole observations, 3-D modeling of the subsurface and geophysical loggings. Within the project, specific representative pilot areas in different geomorphological settings are defined where detailed geospatial building ground investigations are conducted, providing a robust basis for sustainable urban planning related to natural and technological hazards and their associated risks.

Eastern Denali Fault surface trace map, eastern Alaska and Yukon, Canada

USGS Publications Warehouse

Bender, Adrian M.; Haeussler, Peter J.

2017-05-04

We map the 385-kilometer (km) long surface trace of the right-lateral, strike-slip Denali Fault between the Totschunda-Denali Fault intersection in Alaska, United States and the village of Haines Junction, Yukon, Canada. In Alaska, digital elevation models based on light detection and ranging and interferometric synthetic aperture radar data enabled our fault mapping at scales of 1:2,000 and 1:10,000, respectively. Lacking such resources in Yukon, we developed new structure-from-motion digital photogrammetry products from legacy aerial photos to map the fault surface trace at a scale of 1:10,000 east of the international border. The section of the fault that we map, referred to as the Eastern Denali Fault, did not rupture during the 2002 Denali Fault earthquake (moment magnitude 7.9). Seismologic, geodetic, and geomorphic evidence, along with a paleoseismic record of past ground-rupturing earthquakes, demonstrate Holocene and contemporary activity on the fault, however. This map of the Eastern Denali Fault surface trace complements other data sets by providing an openly accessible digital interpretation of the location, length, and continuity of the fault’s surface trace based on the accompanying digital topography dataset. Additionally, the digitized fault trace may provide geometric constraints useful for modeling earthquake scenarios and related seismic hazard.

Digital soil mapping as a basis for climatically oriented agriculture a thematic on the territory of the national crop testing fields of the Republic of Tatarstan, Russia

NASA Astrophysics Data System (ADS)

Sahabiev, I. A.; Giniyatullin, K. G.; Ryazanov, S. S.

2018-01-01

The concept of climate-optimized agriculture (COA) of the UN FAO implies the transformation of agriculture techniques in conditions of changing climate. It is important to implement a timely transition to the concept of COA and sustainable development of soil resources, accurate digital maps of spatial distribution of soils and soil properties are needed. Digital mapping of soil humus content was carried out on the territory of the national crop testing fields (NCTF) of the Republic of Tatarstan (Russian Federation) and the accuracy of the maps obtained was estimated.

High-resolution mapping and spatial variability of soil organic carbon storage of permafrost-affected soils

NASA Astrophysics Data System (ADS)

Siewert, Matthias; Hugelius, Gustaf

2017-04-01

Permafrost-affected soils store large amounts of soil organic carbon (SOC). Mapping of this SOC provides a first order spatial input variable for research that relates carbon stored in permafrost regions to carbon cycle dynamics. High-resolution satellite imagery is becoming increasingly available even in circum-polar regions. The presented research highlights findings of high-resolution mapping efforts of SOC from five study areas in the northern circum-polar permafrost region. These study areas are located in Siberia (Kytalyk, Spasskaya Pad /Neleger, Lena delta), Northern Sweden (Abisko) and Northwestern Canada (Herschel Island). Our high spatial resolution analyses show how geomorphology has a strong influence on the distribution of SOC. This is organized at different spatial scales. Periglacial landforms and processes dictate local scale SOC distribution due to patterned ground. Such landforms are non-sorted circles and ice-wedge polygons of different age and scale. Palsas and peat plateaus are formed and can cover larger areas in Sub-Arctic environments. Study areas that have not been affected by Pleistocene glaciation feature ice-rich Yedoma sediments that dominate the local relief through thermokarst formation and create landscape scale macro environments that dictate the distribution of SOC. A general trend indicates higher SOC storage in Arctic tundra soils compared to forested Boreal or Sub-Arctic taiga soils. Yet, due to the shallower active layer depth in the Arctic, much of the SOC may be permanently frozen and thus not be available to ecosystem processes. Significantly more SOC is stored in soils compared to vegetation, indicating that vegetation growth and incorporation of the carbon into the plant phytomass alone will not be able to offset SOC released from permafrost. This contribution also addresses advances in thematic mapping methods and digital soil mapping of SOC in permafrost terrain. In particular machine-learning methods, such as support vector machines, artificial neural networks and random forests show promising results as a toolbox for mapping permafrost-affected soils. Yet, these new methods do not decrease our dependency from soil pedon data from the field. In contrary, soil pedon data represents an urgent research priority. Statistical analyses are provided as an indication for best practice of soil pedon sampling for the quantification and the model representation of SOC stored in permafrost-affected soils.

Identification, prediction, and mitigation of sinkhole hazards in evaporite karst areas

USGS Publications Warehouse

Gutierrez, F.; Cooper, A.H.; Johnson, K.S.

2008-01-01

Sinkholes usually have a higher probability of occurrence and a greater genetic diversity in evaporite terrains than in carbonate karst areas. This is because evaporites have a higher solubility and, commonly, a lower mechanical strength. Subsidence damage resulting from evaporite dissolution generates substantial losses throughout the world, but the causes are only well understood in a few areas. To deal with these hazards, a phased approach is needed for sinkhole identification, investigation, prediction, and mitigation. Identification techniques include field surveys and geomorphological mapping combined with accounts from local people and historical sources. Detailed sinkhole maps can be constructed from sequential historical maps, recent topographical maps, and digital elevation models (DEMs) complemented with building-damage surveying, remote sensing, and high-resolution geodetic surveys. On a more detailed level, information from exposed paleosubsidence features (paleokarst), speleological explorations, geophysical investigations, trenching, dating techniques, and boreholes may help in investigating dissolution and subsidence features. Information on the hydrogeological pathways including caves, springs, and swallow holes are particularly important especially when corroborated by tracer tests. These diverse data sources make a valuable database-the karst inventory. From this dataset, sinkhole susceptibility zonations (relative probability) may be produced based on the spatial distribution of the features and good knowledge of the local geology. Sinkhole distribution can be investigated by spatial distribution analysis techniques including studies of preferential elongation, alignment, and nearest neighbor analysis. More objective susceptibility models may be obtained by analyzing the statistical relationships between the known sinkholes and the conditioning factors. Chronological information on sinkhole formation is required to estimate the probability of occurrence of sinkholes (number of sinkholes/km2 year). Such spatial and temporal predictions, frequently derived from limited records and based on the assumption that past sinkhole activity may be extrapolated to the future, are non-corroborated hypotheses. Validation methods allow us to assess the predictive capability of the susceptibility maps and to transform them into probability maps. Avoiding the most hazardous areas by preventive planning is the safest strategy for development in sinkhole-prone areas. Corrective measures could be applied to reduce the dissolution activity and subsidence processes. A more practical solution for safe development is to reduce the vulnerability of the structures by using subsidence-proof designs. ?? 2007 Springer-Verlag.

Mapping soil texture classes and optimization of the result by accuracy assessment

NASA Astrophysics Data System (ADS)

Laborczi, Annamária; Takács, Katalin; Bakacsi, Zsófia; Szabó, József; Pásztor, László

2014-05-01

There are increasing demands nowadays on spatial soil information in order to support environmental related and land use management decisions. The GlobalSoilMap.net (GSM) project aims to make a new digital soil map of the world using state-of-the-art and emerging technologies for soil mapping and predicting soil properties at fine resolution. Sand, silt and clay are among the mandatory GSM soil properties. Furthermore, soil texture class information is input data of significant agro-meteorological and hydrological models. Our present work aims to compare and evaluate different digital soil mapping methods and variables for producing the most accurate spatial prediction of texture classes in Hungary. In addition to the Hungarian Soil Information and Monitoring System as our basic data, digital elevation model and its derived components, geological database, and physical property maps of the Digital Kreybig Soil Information System have been applied as auxiliary elements. Two approaches have been applied for the mapping process. At first the sand, silt and clay rasters have been computed independently using regression kriging (RK). From these rasters, according to the USDA categories, we have compiled the texture class map. Different combinations of reference and training soil data and auxiliary covariables have resulted several different maps. However, these results consequentially include the uncertainty factor of the three kriged rasters. Therefore we have suited data mining methods as the other approach of digital soil mapping. By working out of classification trees and random forests we have got directly the texture class maps. In this way the various results can be compared to the RK maps. The performance of the different methods and data has been examined by testing the accuracy of the geostatistically computed and the directly classified results. We have used the GSM methodology to assess the most predictive and accurate way for getting the best among the several result maps. Acknowledgement: Our work was supported by the Hungarian National Scientific Research Foundation (OTKA, Grant No. K105167).

Beyond data collection in digital mapping: interpretation, sketching and thought process elements in geological map making

NASA Astrophysics Data System (ADS)

Watkins, Hannah; Bond, Clare; Butler, Rob

2016-04-01

Geological mapping techniques have advanced significantly in recent years from paper fieldslips to Toughbook, smartphone and tablet mapping; but how do the methods used to create a geological map affect the thought processes that result in the final map interpretation? Geological maps have many key roles in the field of geosciences including understanding geological processes and geometries in 3D, interpreting geological histories and understanding stratigraphic relationships in 2D and 3D. Here we consider the impact of the methods used to create a map on the thought processes that result in the final geological map interpretation. As mapping technology has advanced in recent years, the way in which we produce geological maps has also changed. Traditional geological mapping is undertaken using paper fieldslips, pencils and compass clinometers. The map interpretation evolves through time as data is collected. This interpretive process that results in the final geological map is often supported by recording in a field notebook, observations, ideas and alternative geological models explored with the use of sketches and evolutionary diagrams. In combination the field map and notebook can be used to challenge the map interpretation and consider its uncertainties. These uncertainties and the balance of data to interpretation are often lost in the creation of published 'fair' copy geological maps. The advent of Toughbooks, smartphones and tablets in the production of geological maps has changed the process of map creation. Digital data collection, particularly through the use of inbuilt gyrometers in phones and tablets, has changed smartphones into geological mapping tools that can be used to collect lots of geological data quickly. With GPS functionality this data is also geospatially located, assuming good GPS connectivity, and can be linked to georeferenced infield photography. In contrast line drawing, for example for lithological boundary interpretation and sketching, is yet to find the digital flow that is achieved with pencil on notebook page or map. Free-form integrated sketching and notebook functionality in geological mapping software packages is in its nascence. Hence, the result is a tendency for digital geological mapping to focus on the ease of data collection rather than on the thoughts and careful observations that come from notebook sketching and interpreting boundaries on a map in the field. The final digital geological map can be assessed for when and where data was recorded, but the thought processes of the mapper are less easily assessed, and the use of observations and sketching to generate ideas and interpretations maybe inhibited by reliance on digital mapping methods. All mapping methods used have their own distinct advantages and disadvantages and with more recent technologies both hardware and software issues have arisen. We present field examples of using conventional fieldslip mapping, and compare these with more advanced technologies to highlight some of the main advantages and disadvantages of each method and discuss where geological mapping may be going in the future.

IPL Processing of the Viking Orbiter Images of Mars

NASA Technical Reports Server (NTRS)

Ruiz, R. M.; Elliott, D. A.; Yagi, G. M.; Pomphrey, R. B.; Power, M. A.; Farrell, W., Jr.; Lorre, J. J.; Benton, W. D.; Dewar, R. E.; Cullen, L. E.

1977-01-01

The Viking orbiter cameras returned over 9000 images of Mars during the 6-month nominal mission. Digital image processing was required to produce products suitable for quantitative and qualitative scientific interpretation. Processing included the production of surface elevation data using computer stereophotogrammetric techniques, crater classification based on geomorphological characteristics, and the generation of color products using multiple black-and-white images recorded through spectral filters. The Image Processing Laboratory of the Jet Propulsion Laboratory was responsible for the design, development, and application of the software required to produce these 'second-order' products.

Digital Elevation Models

USGS Publications Warehouse

,

1993-01-01

The Earth Science Information Center (ESIC) distributes digital cartographic/geographic data files produced by the U.S. Geological Survey (USGS) as part of the National Mapping Program. Digital cartographic data files may be grouped into four basic types. The first of these, called a Digital Line Graph (DLG), is the line map information in digital form. These data files include information on base data categories, such as transportation, hypsography, hydrography, and boundaries. The second type, called a Digital Elevation Model (DEM), consists of a sampled array of elevations for a number of ground positions at regularly spaced intervals. The third type is Land Use and Land Cover digital data which provides information on nine major classes of land use such as urban, agricultural, or forest as well as associated map data such as political units and Federal land ownership. The fourth type, the Geographic Names Information System, provides primary information for all known places, features, and areas in the United States identified by a proper name.

EAARL topography: Fire Island National Seashore

USGS Publications Warehouse

Brock, John C.; Wright, C. Wayne; Patterson, Matt; Nayagandhi, Amar; Patterson, Judd

2007-01-01

This Web site contains 31 LIDAR-derived first return topography maps and GIS files for Fire Island National Seashore. These lidar-derived topographic maps were produced as a collaborative effort between the U.S. Geological Survey (USGS) Coastal and Marine Geology Program, the National Park Service (NPS), Northeast Coastal and Barrier Network, Inventory and Monitoring Program, and the National Aeronautics and Space Administration (NASA) Wallops Flight Facility. The aims of the partnership that created this product are to develop advanced survey techniques for mapping barrier island geomorphology and habitats, and to enable the monitoring of ecological and geological change within National Seashores. This product is based on data from an innovative airborne lidar instrument under development at the NASA Wallops Flight Facility, the NASA Experimental Advanced Airborne Research Lidar (EAARL).

Analysis of ERTS imagery of Wyoming and its application to evaluation of Wyoming's natural resources

NASA Technical Reports Server (NTRS)

Houston, R. S. (Principal Investigator); Marrs, R. W.

1972-01-01

The author has identified the following significant results. The Wyoming ERTS investigation has been hindered only slightly by incomplete ERTS data sets and lack of coverage. Efforts to map cultural development, vegetation distributions, and various geomorphologic features are underway. Tectonic analysis of the Rock Springs area has isolated two linear features that may be very significant with regard to the regional structure of central Wyoming. Studies of the fracture systems of the Wind River Mountains are being completed. The fracture map, constructed from ERTS-1 interpretations, contains a great deal of structural information which was previously unavailable. Mapping of the Precambrian metasedimentary and metavolcanic terrain of the Granite Mountains is nearing completion, and interpretation of ERTS supporting aircraft data has revealed deposits of iron formation.

Geologic map of outcrop areas of sedimentary units in the eastern part of the Hailey 1 degree x 2 degrees quadrangle and part of the southern part of the Challis 1 degree x 2 degrees quadrangle, south-central Idaho

USGS Publications Warehouse

Link, P.K.; Mahoney, J.B.; Bruner, D.J.; Batatian, L.D.; Wilson, Eric; Williams, F.J.C.

1995-01-01

The paper version of the Geologic map of outcrop areas of sedimentary units in the eastern part of the Hailey 1x2 Quadrangle and part of the southern part of the Challis 1x2 Quadrangle, south-central Idaho was compiled by Paul Link and others in 1995. The plate was compiled on a 1:100,000 scale topographic base map. TechniGraphic System, Inc. of Fort Collins Colorado digitized this map under contract for N.Shock. G.Green edited and prepared the digital version for publication as a GIS database. The digital geologic map database can be queried in many ways to produce a variety of geologic maps.

Reconnaissance geologic mapping of a portion of the rain‐forest‐covered Guiana Shield, Northwestern Brazil, using SIR-B and digital aeromagnetic data

USGS Publications Warehouse

Pellon de Miranda, Fernando; McCafferty, Anne E.; Taranik, James V.

1994-01-01

This paper documents the result of an integrated analysis of spaceborne radar (SIR-B) and digital aeromagnetic data carried out in the heavily forested Guiana Shield. The objective of the research is to interpret the geophysical data base to its limit to produce a reconnaissance geologic map as an aid to ground work planning in a worst‐case setting. Linear geomorphic features were identified based on the interpretation of the SIR-B image. Digital manipulation of aeromagnetic data allowed the development of a color‐shaded relief map of reduced‐to‐pole magnetic anomalies, a terrace‐magnetization map, and a map showing the location of maximum values of the horizontal component of the pseudogravity gradient (magnetization boundary lines). The resultant end product was a reconnaissance geologic map where broad terrane categories were delineated and geologic faults with both topographic and magnetic expression were defined. The availability of global spaceborne radar coverage in the 1990s and the large number of existing digital aeromagnetic surveys in northwestern Brazil indicate that this approach can be potentially useful for reconnaissance geologic mapping elsewhere in the Guiana Shield.

The National Map - Orthoimagery

USGS Publications Warehouse

Mauck, James; Brown, Kim; Carswell, William J.

2009-01-01

Orthorectified digital aerial photographs and satellite images of 1-meter (m) pixel resolution or finer make up the orthoimagery component of The National Map. The process of orthorectification removes feature displacements and scale variations caused by terrain relief and sensor geometry. The result is a combination of the image characteristics of an aerial photograph or satellite image and the geometric qualities of a map. These attributes allow users to: *Measure distance *Calculate areas *Determine shapes of features *Calculate directions *Determine accurate coordinates *Determine land cover and use *Perform change detection *Update maps The standard digital orthoimage is a 1-m or finer resolution, natural color or color infra-red product. Most are now produced as GeoTIFFs and accompanied by a Federal Geographic Data Committee (FGDC)-compliant metadata file. The primary source for 1-m data is the National Agriculture Imagery Program (NAIP) leaf-on imagery. The U.S. Geological Survey (USGS) utilizes NAIP imagery as the image layer on its 'Digital- Map' - a new generation of USGS topographic maps (http://nationalmap.gov/digital_map). However, many Federal, State, and local governments and organizations require finer resolutions to meet a myriad of needs. Most of these images are leaf-off, natural-color products at resolutions of 1-foot (ft) or finer.

Hard Copy to Digital Transfer: 3D Models that Match 2D Maps

ERIC Educational Resources Information Center

Kellie, Andrew C.

2011-01-01

This research describes technical drawing techniques applied in a project involving digitizing of existing hard copy subsurface mapping for the preparation of three dimensional graphic and mathematical models. The intent of this research was to identify work flows that would support the project, ensure the accuracy of the digital data obtained,…

Moving Digital Libraries into the Student Learning Space: The GetSmart Experience

ERIC Educational Resources Information Center

Marshall, Byron B.; Chen, Hsinchun; Shen, Rao; Fox, Edward A.

2006-01-01

The GetSmart system was built to support theoretically sound learning processes in a digital library environment by integrating course management, digital library, and concept mapping components to support a constructivist, six-step, information search process. In the fall of 2002 more than 100 students created 1400 concept maps as part of…

SCANIT: centralized digitizing of forest resource maps or photographs

Treesearch

Elliot L. Amidon; E. Joyce Dye

1981-01-01

Spatial data on wildland resource maps and aerial photographs can be analyzed by computer after digitizing. SCANIT is a computerized system for encoding such data in digital form. The system, consisting of a collection of computer programs and subroutines, provides a powerful and versatile tool for a variety of resource analyses. SCANIT also may be converted easily to...

Historical patterns of spruce budworm defoliation and bark beetle outbreaks in North American conifer forests: an atlas and description of digital maps

Treesearch

David W. Williams; Richard A. Birdsey

2003-01-01

This atlas presents maps of historical defoliation by the eastern and western spruce budworms and historical outbreaks of the mountain and southern pine beetles during the past half century. The maps encompass various regions of the conterminous United States and eastern Canada. This publication also serves as documentation for an extended set of digital maps, which...

Coastal bathymetry and backscatter data collected in 2012 from the Chandeleur Islands, Louisiana

USGS Publications Warehouse

DeWitt, Nancy T.; Bernier, Julie C.; Pfeiffer, William R.; Miselis, Jennifer L.; Reynolds, B.J.; Wiese, Dana S.; Kelso, Kyle W.

2014-01-01

As part of the Barrier Island Evolution Research Project, scientists from the U.S. Geological Survey St. Petersburg Coastal and Marine Science Center conducted nearshore geophysical surveys off the northern Chandeleur Islands, Louisiana, in July and August of 2012. The objective of the study is to better understand barrier island geomorphic evolution, particularly storm-related depositional and erosional processes that shape the islands over annual to interannual timescales (1-5 years). Collecting geophysical data will allow us to identify relationships between the geologic history of the island and its present day morphology and sediment distribution. This mapping effort was the second in a series of three planned surveys in this area. High resolution geophysical data collected in each of 3 consecutive years along this rapidly changing barrier island system will provide a unique time-series dataset that will significantly further the analyses and geomorphological interpretations of this and other coastal systems, improving our understanding of coastal response and evolution over short time scales (1-5 years). This Data Series report includes the geophysical data that were collected during two cruises (USGS Field Activity Numbers 12BIM03 and 12BIM04) aboard the RV Survey Cat and the RV Twin Vee along the northern portion of the Chandeleur Islands, Breton National Wildlife Refuge, Louisiana. Data were acquired with the following equipment: a Systems Engineering and Assessment, Ltd., SWATHplus interferometric sonar (468 kilohertz (kHz)), an EdgeTech 424 (4-24 kHz) chirp sub-bottom profiling system, and a Knudsen 320BP (210 kHz) echosounder. This report serves as an archive of processed interferometric swath and single-beam bathymetry data. Geographic information system data products include an interpolated digital elevation model, an acoustic backscatter mosaic, trackline maps, and point data files. Additional files include error analysis maps, Field Activity Collection System logs, and formal Federal Geographic Data Committee metadata. NOTE: These data are scientific in nature and are not to be used for navigation.

Coastal Vulnerability to Sea Level Rise and Erosion in Northwest Alaska (Invited)

NASA Astrophysics Data System (ADS)

Gorokhovich, Y.; Leiserowitz, A.

2009-12-01

Northwest Alaska is experiencing significant climate change and human impacts. The study area includes the coastal zone of Kotzebue Sound and the Chukchi Sea and provides the local population (predominantly Inupiaq Eskimo) with critical subsistence resources of meat, fish, berries, herbs, and wood. The geomorphology of the coast includes barrier islands, inlets, estuaries, deltas, cliffs, bluffs, and beaches that host modern settlements and infrastructure. Coastal dynamics and sea-level rise are contributing to erosion, intermittent erosion/accretion patterns, landslides, slumps and coastal retreat. These factors are causing the sedimentation of deltas and lagoons, and changing local bathymetry, morphological parameters of beaches and underwater slopes, rates of coastal dynamics, and turbidity and nutrient cycling in coastal waters. This study is constructing vulnerability maps to help local people and federal officials understand the potential consequences of sea-level rise and coastal erosion on local infrastructure, subsistence resources, and culturally important sites. A lack of complete and uniform data (in terms of methods of collection, geographic scale and spatial resolution) creates an additional level of uncertainty that complicates geographic analysis. These difficulties were overcome by spatial modeling with selected spatial resolution using extrapolation methods. Data include subsistence resource maps obtained using Participatory GIS with local hunters and elders, geological and geographic data on coastal dynamics from satellite imagery, aerial photos, bathymetry and topographic maps, and digital elevation models. These data were classified and ranked according to the level of coastal vulnerability (Figure 1). The resulting qualitative multicriteria model helps to identify the coastal areas with the greatest vulnerability to coastal erosion and of the potential loss of subsistence resources. Acknowldgements: Dr. Ron Abileah (private consultant, jOmegak) helped in preliminary analysis of Landsat imagery, Mr. Alex Whiting provided valuable information on subsistence resources in Kotzebue region, hunters and elders of villages in Kivalina, Kotzebue, Selawik and Deering provided input in GIS database on subsistence resources.

Emergency response to landslide using GNSS measurements and UAV

NASA Astrophysics Data System (ADS)

Nikolakopoulos, Konstantinos G.; Koukouvelas, Ioannis K.

2017-10-01

Landslide monitoring can be performed using many different methods: Classical geotechnical measurements like inclinometer, topographical survey measurements with total stations or GNSS sensors and photogrammetric techniques using airphotos or high resolution satellite images. However all these methods are expensive or difficult to be developed immediately after the landslide triggering. In contrast airborne technology and especially the use of Unmanned Aerial Vehicles (UAVs) make response to landslide disaster easier as UAVs can be launched quickly in dangerous terrains and send data about the sliding areas to responders on the ground either as RGB images or as videos. In addition, the emergency response to landslide is critical for the further monitoring. For proper displacement identification all the above mentioned monitoring methods need a high resolution and a very accurate representation of the relief. The ideal solution for the accurate and quick mapping of a landslide is the combined use of UAV's photogrammetry and GNSS measurements. UAVs have started their development as expensive toys but they currently became a very valuable tool in large scale mapping of sliding areas. The purpose of this work is to demonstrate an effective solution for the initial landslide mapping immediately after the occurrence of the phenomenon and the possibility of the periodical assessment of the landslide. Three different landslide cases from Greece are presented in the current study. All three landslides have different characteristics: occurred in different geomorphologic environments, triggered by different causes and had different geologic bedrock. In all three cases we performed detailed GNSS measurements of the landslide area, we generated orthophotos as well as Digital Surface Models (DSMs) at an accuracy of less than +/-10 cm. Slide direction and velocity, mass balances as well as protection and mitigation measurements can be derived from the application of the UAVs. Those data in addition are accurate, cost- and time-effective.

Use of slope, aspect, and elevation maps derived from digital elevation model data in making soil surveys

USGS Publications Warehouse

Klingebiel, A.A.; Horvath, E.H.; Moore, D.G.; Reybold, W.U.

1987-01-01

Maps showing different classes of slope, aspect, and elevation were developed from U.S. Geological Survey digital elevation model data. The classes were displayed on clear Mylar at 1:24 000-scale and registered with topographic maps and orthophotos. The maps were used with aerial photographs, topographic maps, and other resource data to determine their value in making order-three soil surveys. They were tested on over 600 000 ha in Wyoming, Idaho, and Nevada under various climatic and topographic conditions. Field evaluations showed that the maps developed from digital elevation model data were accurate, except for slope class maps where slopes were <4%. The maps were useful to soil scientists, especially where (i) class boundaries coincided with soil changes, landform delineations, land use and management separations, and vegetation changes, and (ii) rough terrain and dense vegetation made it difficult to traverse the area. In hot, arid areas of sparse vegetation, the relationship of slope classes to kinds of soil and vegetation was less significant.

Scanning and georeferencing historical USGS quadrangles

USGS Publications Warehouse

Davis, Larry R.; Allord, G.J.

2011-01-01

The USGS Historical Quadrangle Scanning Project (HQSP) is scanning all scales and all editions of approximately 250,000 topographic maps published by the U.S. Geological Survey (USGS) since the inception of the topographic mapping program in 1884. This scanning will provide a comprehensive digital repository of USGS topographic maps, available to the public at no cost. This project serves the dual purpose of creating a master catalog and digital archive copies of the irreplaceable collection of topographic maps in the USGS Reston Map Library as well as making the maps available for viewing and downloading from the USGS Store and The National Map Viewer.

Groundwater favorability map using GIS multicriteria data analysis on crystalline terrain, São Paulo State, Brazil

NASA Astrophysics Data System (ADS)

Madrucci, Vanessa; Taioli, Fabio; de Araújo, Carlos César

2008-08-01

SummaryThis paper presents the groundwater favorability mapping on a fractured terrain in the eastern portion of São Paulo State, Brazil. Remote sensing, airborne geophysical data, photogeologic interpretation, geologic and geomorphologic maps and geographic information system (GIS) techniques have been used. The results of cross-tabulation between these maps and well yield data allowed groundwater prospective parameters in a fractured-bedrock aquifer. These prospective parameters are the base for the favorability analysis whose principle is based on the knowledge-driven method. The multicriteria analysis (weighted linear combination) was carried out to give a groundwater favorability map, because the prospective parameters have different weights of importance and different classes of each parameter. The groundwater favorability map was tested by cross-tabulation with new well yield data and spring occurrence. The wells with the highest values of productivity, as well as all the springs occurrence are situated in the excellent and good favorability mapped areas. It shows good coherence between the prospective parameters and the well yield and the importance of GIS techniques for definition of target areas for detail study and wells location.

Digital version of "Open-File Report 92-179: Geologic map of the Cow Cove Quadrangle, San Bernardino County, California"

USGS Publications Warehouse

Wilshire, Howard G.; Bedford, David R.; Coleman, Teresa

2002-01-01

3. Plottable map representations of the database at 1:24,000 scale in PostScript and Adobe PDF formats. The plottable files consist of a color geologic map derived from the spatial database, composited with a topographic base map in the form of the USGS Digital Raster Graphic for the map area. Color symbology from each of these datasets is maintained, which can cause plot file sizes to be large.

Digital image transformation and rectification of spacecraft and radar images

USGS Publications Warehouse

Wu, S.S.C.

1985-01-01

Digital image transformation and rectification can be described in three categories: (1) digital rectification of spacecraft pictures on workable stereoplotters; (2) digital correction of radar image geometry; and (3) digital reconstruction of shaded relief maps and perspective views including stereograms. Digital rectification can make high-oblique pictures workable on stereoplotters that would otherwise not accommodate such extreme tilt angles. It also enables panoramic line-scan geometry to be used to compile contour maps with photogrammetric plotters. Rectifications were digitally processed on both Viking Orbiter and Lander pictures of Mars as well as radar images taken by various radar systems. By merging digital terrain data with image data, perspective and three-dimensional views of Olympus Mons and Tithonium Chasma, also of Mars, are reconstructed through digital image processing. ?? 1985.

Digitization of a geologic map for the Quebec-Maine-Gulf of Maine global geoscience transect

USGS Publications Warehouse

Wright, Bruce E.; Stewart, David B.

1990-01-01

The Bedrock Geologic Map of Maine was digitized and combined with digital geologic data for Quebec and the Gulf of Maine for the Quebec-Maine-Gulf of Maine Geologic Transect Project. This map is being combined with digital geophysical data to produce three-dimensional depictions of the subsurface geology and to produce cross sections of the Earth's crust. It is an essential component of a transect that stretches from the craton near Quebec City, Quebec, to the Atlantic Ocean Basin south of Georges Bank. The transect is part of the Global Geosciences Transect Project of the International Lithosphere Program. The Digital Line Graph format is used for storage of the digitized data. A coding scheme similar to that used for base category planimetric data was developed to assign numeric codes to the digitized geologic data. These codes were used to assign attributes to polygon and line features to describe rock type, age, name, tectonic setting of original deposition, mineralogy, and composition of igneous plutonic rocks, as well as faults and other linear features. The digital geologic data can be readily edited, rescaled, and reprojected. The attribute codes allow generalization and selective retrieval of the geologic features. The codes allow assignment of map colors based on age, lithology, or other attribute. The Digital Line Graph format is a general transfer format that is supported by many software vendors and is easily transferred between systems.

Reconstructing spatial and temporal patterns of paleoglaciation along the Tian Shan

NASA Astrophysics Data System (ADS)

Harbor, J.; Stroeven, A. P.; Beel, C.; Blomdin, R.; Caffee, M. W.; Chen, Y.; Codilean, A.; Gribenski, N.; Hattestrand, C.; Heyman, J.; Ivanov, M.; Kassab, C.; Li, Y.; Lifton, N. A.; Liu, G.; Petrakov, D.; Rogozhina, I.; Usubaliev, R.

2012-12-01

Testing and calibrating global climate models require well-constrained information on past climates of key regions around the world. Particularly important are transitional regions that provide a sensitive record of past climate change. Central Asia is an extreme continental location with glaciers and rivers that respond sensitively to temporal variations in the dominance of several major climate systems. As an international team initiative, we are reconstructing the glacial history of the Kyrgyz and Chinese Tian Shan, based on mapping and dating of key localities along the range. Remote-sensing-based geomorphological mapping, building on previous maps produced by Kyrgyz, Russian, Chinese and German scholars, is being augmented with field observations of glacial geomorphology and the maximum distribution of erratics. We are using cosmogenic nuclide (CN) 10Be dating of moraines and other landforms that constrain the former maximum extents of glaciers. Study sites include the Ala-Archa, Ak-Shyrak and Inylchek/Sary-Dzaz areas in Kyrgyzstan and the Urumqi valley (as well as its upland and southern slopes), and the Tumur and Bogeda peak areas in China. Comparing consistently dated glacial histories along and across the range will allow us to examine potential shifts in the dominance patterns of climate systems over time in Central Asia. We are also comparing ages based on CN with optically stimulated luminescence (OSL) and electron spin resonance (ESR) dates. The final stage of this project will use intermediate complexity glacier flow models to examine paleoclimatic implications of the observed spatial and temporal patterns of glacier changes across Central Asia and eastern Tibet, focused in particular on the last glacial cycle.

Development of Generation System of Simplified Digital Maps

NASA Astrophysics Data System (ADS)

Uchimura, Keiichi; Kawano, Masato; Tokitsu, Hiroki; Hu, Zhencheng

In recent years, digital maps have been used in a variety of scenarios, including car navigation systems and map information services over the Internet. These digital maps are formed by multiple layers of maps of different scales; the map data most suitable for the specific situation are used. Currently, the production of map data of different scales is done by hand due to constraints related to processing time and accuracy. We conducted research concerning technologies for automatic generation of simplified map data from detailed map data. In the present paper, the authors propose the following: (1) a method to transform data related to streets, rivers, etc. containing widths into line data, (2) a method to eliminate the component points of the data, and (3) a method to eliminate data that lie below a certain threshold. In addition, in order to evaluate the proposed method, a user survey was conducted; in this survey we compared maps generated using the proposed method with the commercially available maps. From the viewpoint of the amount of data reduction and processing time, and on the basis of the results of the survey, we confirmed the effectiveness of the automatic generation of simplified maps using the proposed methods.

Preliminary Geologic Map of the Cook Inlet Region, Alaska-Including Parts of the Talkeetna, Talkeetna Mountains, Tyonek, Anchorage, Lake Clark, Kenai, Seward, Iliamna, Seldovia, Mount Katmai, and Afognak 1:250,000-scale Quadrangles

USGS Publications Warehouse

Wilson, Frederic H.; Hults, Chad P.; Schmoll, Henry R.; Haeussler, Peter J.; Schmidt, Jeanine M.; Yehle, Lynn A.; Labay, Keith A.; Shew, Nora B.

2009-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. The files named __geol contain geologic polygons and line (contact) attributes; files named __fold contain fold axes; files named __lin contain lineaments; and files named __dike contain dikes as lines. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

FGDC Digital Cartographic Standard for Geologic Map Symbolization (PostScript Implementation)

USGS Publications Warehouse

,

2006-01-01

PLEASE NOTE: This now-approved 'FGDC Digital Cartographic Standard for Geologic Map Symbolization (PostScript Implementation)' officially supercedes its earlier (2000) Public Review Draft version (see 'Earlier Versions of the Standard' below). In August 2006, the Digital Cartographic Standard for Geologic Map Symbolization was officially endorsed by the Federal Geographic Data Committee (FGDC) as the national standard for the digital cartographic representation of geologic map features (FGDC Document Number FGDC-STD-013-2006). Presented herein is the PostScript Implementation of the standard, which will enable users to directly apply the symbols in the standard to geologic maps and illustrations prepared in desktop illustration and (or) publishing software. The FGDC Digital Cartographic Standard for Geologic Map Symbolization contains descriptions, examples, cartographic specifications, and notes on usage for a wide variety of symbols that may be used on typical, general-purpose geologic maps and related products such as cross sections. The standard also can be used for different kinds of special-purpose or derivative map products and databases that may be focused on a specific geoscience topic (for example, slope stability) or class of features (for example, a fault map). The standard is scale-independent, meaning that the symbols are appropriate for use with geologic mapping compiled or published at any scale. It will be useful to anyone who either produces or uses geologic map information, whether in analog or digital form. Please be aware that this standard is not intended to be used inflexibly or in a manner that will limit one's ability to communicate the observations and interpretations gained from geologic mapping. In certain situations, a symbol or its usage might need to be modified in order to better represent a particular feature on a geologic map or cross section. This standard allows the use of any symbol that doesn't conflict with others in the standard, provided that it is clearly explained on the map and in the database. In addition, modifying the size, color, and (or) lineweight of an existing symbol to suit the needs of a particular map or output device also is permitted, provided that the modified symbol's appearance is not too similar to another symbol on the map. Be aware, however, that reducing lineweights below .125 mm (.005 inch) may cause symbols to plot incorrectly if output at higher resolutions (1800 dpi or higher). For guidelines on symbol usage, as well as on color design and map labeling, please refer to the standard's introductory text. Also found there are informational sections covering concepts of geologic mapping and some definitions of geologic map features, as well as sections on the newly defined concepts and terminology for the scientific confidence and locational accuracy of geologic map features. More information on both the past development and the future maintenance of the FGDC Digital Cartographic Standard for Geologic Map Symbolization can be found at the FGDC Geologic Data Subcommittee website (http://ngmdb.usgs.gov/fgdc_gds/). Earlier Versions of the Standard

Vegetation and terrain mapping in Alaska using Landsat MSS and digital terrain data

USGS Publications Warehouse

Shasby, Mark; Carneggie, David M.

1986-01-01

During the past 5 years, the U.S. Geological Survey's (USGS) Earth Resources Observation Systems (EROS) Data Center Field Office in Anchorage, Alaska has worked cooperatively with Federal and State resource management agencies to produce land-cover and terrain maps for 245 million acres of Alaska. The need for current land-cover information in Alaska comes principally from the mandates of the Alaska National Interest Lands Conservation Act (ANILCA), December 1980, which requires major land management agencies to prepare comprehensive management plans. The land-cover mapping projects integrate digital Landsat data, terrain data, aerial photographs, and field data. The resultant land-cover and terrain maps and associated data bases are used for resource assessment, management, and planning by many Alaskan agencies including the U.S. Fish and Wildlife Service, U.S. Forest Service, Bureau of Land Management, and Alaska Department of Natural Resources. Applications addressed through use of the digital land-cover and terrain data bases range from comprehensive refuge planning to multiphased sampling procedures designed to inventory vegetation statewide. The land-cover mapping programs in Alaska demonstrate the operational utility of digital Landsat data and have resulted in a new land-cover mapping program by the USGS National Mapping Division to compile 1:250,000-scale land-cover maps in Alaska using a common statewide land-cover map legend.

Enhancing rescue-archaeology using geomorphological approaches: Archaeological sites in Paredes (Asturias, NW Spain)

NASA Astrophysics Data System (ADS)

Jiménez-Sánchez, M.; González-Álvarez, I.; Requejo-Pagés, O.; Domínguez-Cuesta, M. J.

2011-09-01

Palaeolithic remnants, a Necropolis (Roman villa), and another minor archaeological site were discovered in Paredes (Spain). These sites were the focus of multidisciplinary research during the construction of a large shopping centre in Asturias (NW Spain). The aims of this study are (1) to contribute to archaeological prospection in the sites and (2) to develop evolutionary models of the sites based on geomorphological inferences. Detailed archaeological prospection (103 trenches), geomorphologic mapping, stratigraphic studies (36 logs) and ground penetration radar (GPR) surveys on five profiles indicate that the location of the settlement source of the Necropolis is outside the construction perimeter, farther to the southeast. The Pre-Holocene evolution of the fluvial landscape is marked by the development of two terraces (T1 and T2) that host the Early Palaeolithic remains in the area (ca 128-71 ka). The Holocene evolution of the landscape was marked by the emplacement of the Nora River flood plain, covered by alluvial fans after ca. 9 ka BP (cal BC 8252-7787). Subsequently, Neolithic pebble pits dated ca. 5.3 ka BP (cal BC 4261-3963 and 4372-4051) were constructed on T2, at the area reoccupied as a Necropolis during the Late Roman period, 1590 ± 45 years BP (cal AD 382-576). Coeval human activity during the Late Roman period at 1670 ± 60 years BP (cal AD 320-430) is also recorded by channel infill sediments in a minor site at the margin of an alluvial fan located to the southeast. This work shows that a rescue-archaeological study can be significantly enhanced by the implementation of multidisciplinary scientific studies, in which the holistic view of geomorphologic settings provide key insights into the geometry and evolution of archaeological sites.

Hydro-geomorphological characterization and classification of Chilean river networks using horizontal, vertical and climatological properties

NASA Astrophysics Data System (ADS)

Pereira, A. A.; Gironas, J. A.; Passalacqua, P.; Mejia, A.; Niemann, J. D.

2017-12-01

Previous work has shown that lithological, tectonic and climatic processes have a major influence in shaping the geomorphology of river networks. Accordingly, quantitative classification methods have been developed to identify and characterize network types (dendritic, parallel, pinnate, rectangular and trellis) based solely on the self-affinity of their planform properties, computed from available Digital Elevation Model (DEM) data. In contrast, this research aim is to include both horizontal and vertical properties to evaluate a quantitative classification method for river networks. We include vertical properties to consider the unique surficial conditions (e.g., large and steep height drops, volcanic activity, and complexity of stream networks) of the Andes Mountains. Furthermore, the goal of the research is also to explain the implications and possible relations between the hydro-geomorphological properties and climatic conditions. The classification method is applied to 42 basins in the southern Andes in Chile, ranging in size from 208 Km2 to 8,000 Km2. The planform metrics include the incremental drainage area, stream course irregularity and junction angles, while the vertical metrics include the hypsometric curve and the slope-area relationship. We introduce new network structures (Brush, Funnel and Low Sinuosity Rectangular), possibly unique to the Andes, that can be quantitatively differentiated from previous networks identified in other geographic regions. Then, this research evaluates the effect that excluding different Strahler order streams has on the horizontal properties and therefore in the classification. We found that climatic conditions are not only linked to horizontal parameters, but also to vertical ones, finding significant correlation between climatic variables (average near-surface temperature and rainfall) and vertical measures (parameters associated with the hypsometric curve and slope-area relation). The proposed classification shows differences among basins previously classified as the same type, which are not noticeable in their horizontal properties and helps reduce misclassifications within the old clusters. Additional hydro-geomorphological metrics are to be considered in the classification method to improve the effectiveness of it.

Digital mapping in extreme and remote environments

NASA Astrophysics Data System (ADS)

Andersson, Joel; Bauer, Tobias; Sarlus, Zimer; Zainy, Maher; Brethes, Anais

2017-04-01

During the last few years, Luleå University of Technology has performed a series of research projects in remote areas with extreme climatic conditions using digital mapping technologies. The majority of past and ongoing research projects focus on the arctic regions of the Fennoscandian Shield and Greenland but also on the Zagros fold-and-thrust belt in northern Iraq. Currently, we use the Midland Valley application FieldMove on iPad mini devices with ruggedized casings. As all projects have a strong focus on geological field work, harsh climatic conditions are a challenge not only for the geologists but also for the digital mapping hardware. In the arctic regions especially cold temperatures affect battery lifetime and performance of the screens. But also high temperatures are restricting digital mapping. From experience, a typical temperature range where digital mapping, using iPad tablets, is possible lies between -20 and +40 degrees. Furthermore, the remote character of field areas complicates access but also availability of electricity. By a combination of robust solar chargers and ruggedized batteries we are able to work entirely autarkical. Additionally, we are currently installing a drone system that allows us to map outcrops normally inaccessible because of safety reasons or time deficiency. The produced data will subsequently be taken into our Virtual Reality studio for interpretation and processing. There we will be able to work also with high resolution DEM data from Lidar scanning allowing us to interpret structural features such as post-glacial faults in areas that are otherwise only accessible by helicopter. By combining digital field mapping with drone technique and a Virtual Reality studio we are able to work in hardly accessible areas, improve safety during field work and increase efficiency substantially.

Soils of Walker Branch Watershed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lietzke, D.A.

1994-03-01

The soil survey of Walker Branch Watershed (WBW) utilized the most up-to-date knowledge of soils, geology, and geohydrology in building the soils data base needed to reinterpret past research and to begin new research in the watershed. The soils of WBW were also compared with soils mapped elsewhere along Chestnut Ridge on the Oak Ridge Reservation to (1) establish whether knowledge obtained elsewhere could be used within the watershed, (2) determine whether there were any soils restricted to the watershed, and (3) evaluate geologic formation lateral variability. Soils, surficial geology, and geomorphology were mapped at a scale of 1:1,200 usingmore » a paper base map having 2-ft contour intervals. Most of the contours seemed to reasonably represent actual landform configurations, except for dense wooded areas. For example, the very large dolines or sinkholes were shown on the contour base map, but numerous smaller ones were not. In addition, small drainageways and gullies were often not shown. These often small but important features were located approximately as soil mapping progressed.« less