Crystallization of calcium oxalate dihydrate in a buffered calcium-containing glucose solution by irradiation with non-equilibrium atmospheric pressure plasma

NASA Astrophysics Data System (ADS)

Kurake, Naoyuki; Tanaka, Hiromasa; Ishikawa, Kenji; Nakamura, Kae; Kajiyama, Hiroaki; Kikkawa, Fumitaka; Mizuno, Masaaki; Ikehara, Yuzuru; Hori, Masaru

2017-10-01

Oxalate was synthesized in the glucose solution by irradiation with non-equilibrium atmospheric pressure plasma (NEAPP), in which the NEAPP plume contacted the solution surface, via the generation of several intermediate organic products such as gluconic acid. A thermodynamically unstable phase of calcium oxalate dihydrate crystallized rapidly during incubation of a NEAPP-irradiated glucose solution that contained calcium ions and was buffered at neutral pH. Longer irradiation times increased the growth rate and the number of seed crystals.

Synthesis, structural, thermal and optical studies of 1-ethyl-2,6-dimethyl-4-hydroxy pyridinium halides.

PubMed

Dhanuskodi, S; Manivannan, S; Kirschbaum, K

2006-05-15

1-Ethyl-2,6-dimethyl-4-hydroxy pyridinium chloride dihydrate and bromide dihydrate salts have been synthesized and their single crystals were grown by the slow evaporation of aqueous solution at 30 degrees C. The grown crystals were characterized by elemental analysis, FT-NMR and FT-IR techniques to confirm the formation of the expected compound. Optical transmittance window in aqueous solution was found to be 275-1100 nm by UV-vis-NIR technique. Thermogravimetric and differential thermal analyses reveal thermal stability and the presence of two water molecules in the crystal lattices. The crystal structure of chloride salt was also determined by X-ray diffraction method.

Crystallization of calcium sulfate dihydrate in the presence of some metal ions

NASA Astrophysics Data System (ADS)

Hamdona, Samia K.; Al Hadad, Umaima A.

2007-02-01

Crystallization of calcium sulfate dihydrate (CaSO 4·2H 2O gypsum) in sodium chloride solutions in the presence of some metal ions, and over a range of relative super-saturation has been studied. The addition of metal ions, even at relatively low concentration (10 -6 mol l -1), markedly retard the rate of crystallization of gypsum. Retardation effect was enhanced with increase in the additives contents. Moreover, the effect was enhanced as the relative super-saturation decreases. Influence of mixed additives on the rate of crystallization (Cd 2++Arg, Cd 2++H 3PO 4 and Cd 2++PAA) has also been studied. Direct adsorption experiments of these metal ions on the surface of gypsum crystals have been made for comparison.

Crystal growth, thermal and optical studies of semiorganic nonlinear optical material: L-lysine hydrochloride dihydrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalaiselvi, D.; Mohan Kumar, R.; Jayavel, R.

2008-07-01

Single crystals of L-lysine hydrochloride dihydrate (LLHCD), a nonlinear optical material, have been grown by slow cooling technique from its aqueous solution. LLHCD was found to be highly soluble in water. The grown crystals have been subjected to single crystal X-ray diffraction to confirm the structure and to estimate the lattice parameters. The vibrational structure of the molecule is elucidated from FTIR spectra. Thermal analysis revealed the thermal stability of the grown crystals. The optical transmittance spectrum shows that the material possesses good optical transparency in the entire visible region with a UV cut-off wavelength at 228 nm. The mechanicalmore » properties of the grown crystal have been studied using Vicker's microhardness test. The laser damage threshold of 52.25 MW/cm{sup 2} has been measured by irradiating Q-switched Nd:YAG laser (1064 nm)« less

Ultrasonographic findings of Achilles tendon and plantar fascia in patients with calcium pyrophosphate deposition disease.

PubMed

Ellabban, Abdou S; Kamel, Shereen R; Abo Omar, Hanaa A S; El-Sherif, Ashraf M H; Abdel-Magied, Rasha A

2012-04-01

The aims of the study were to detect the frequency of involvement of the Achilles tendon and plantar fascia in patients with calcium pyrophosphate deposition disease (CPPD) by high-frequency gray-scale ultrasonography (US) and power Doppler sonography (PDS) and to correlate these findings with demographic and clinical data. Two groups of patients were enrolled: group I (38 patients with CPPD) and group II (22 patients with knee OA). US/PDS examination of the heels was performed to both groups. In the CPPD group, US/PDS examination of the Achilles tendon revealed: calcification in 57.9%, enthesophytosis in 57.9%, enthesopathy in 23.7%, vascular sign in 21%, bursitis in 13.2%, and cortical bone irregularity in 10.5%. US/PDS examination of plantar fascia in the CPPD group revealed: calcification in 15.8%, cortical bone irregularity in 78.9%, enthesophytosis in 60.5%, and planter fasciitis in 42.1%. In patients with CPPD, age was significantly correlated with enthesophytosis and deep retrocalcaneal bursitis (p = 0.01 and p = 0.04, respectively). Heel tenderness and posterior talalgia were significantly correlated with Achilles tendon enthesopathy, vascular sign, and deep retrocalcaneal bursitis (p = 0.0001 for each). Inferior talalgia was significantly correlated with plantar fasciitis (p = 0.0001). The sensitivity of ultrasonography for detection of calcifications in Achilles tendon and plantar fascia was 57.9% and 15.8%, respectively, and the specificity was 100% for both. To conclude, ultrasonographic Achilles tendon and plantar fascia calcifications are frequent findings in patients with CPPD. These calcifications have a high specificity and can be used as a useful indirect sign of CPPD.

Crystal growth, structural, thermal and mechanical behavior of l-arginine 4-nitrophenolate 4-nitrophenol dihydrate (LAPP) single crystals.

PubMed

Mahadevan, M; Ramachandran, K; Anandan, P; Arivanandhan, M; Bhagavannarayana, G; Hayakawa, Y

2014-12-10

Single crystals of l-arginine 4-nitrophenolate 4-nitrophenol dihydrate (LAPP) have been grown successfully from the solution of l-arginine and 4-nitrophenol. Slow evaporation of solvent technique was adopted to grow the bulk single crystals. Single crystal X-ray diffraction analysis confirms the grown crystal has monoclinic crystal system with space group of P21. Powder X-ray diffraction analysis shows the good crystalline nature. The crystalline perfection of the grown single crystals was analyzed by HRXRD by employing a multicrystal X-ray diffractometer. The functional groups were identified from proton NMR spectroscopic analysis. Linear and nonlinear optical properties were determined by UV-Vis spectrophotometer and Kurtz powder technique respectively. It is found that the grown crystal has no absorption in the green wavelength region and the SHG efficiency was found to be 2.66 times that of the standard KDP. The Thermal stability of the crystal was found by obtaining TG/DTA curve. The mechanical behavior of the grown crystal has been studied by Vicker's microhardness method. Copyright © 2014 Elsevier B.V. All rights reserved.

Electron irradiation induced effects on the physico-chemical properties of L-Arginine Maleate Dihydrate (LAMD) single crystals

NASA Astrophysics Data System (ADS)

Thomas, Prince; Dhole, S. D.; Joseph, Ginson P.

2018-07-01

Single crystals of L-Arginine Maleate Dihydrate (LAMD) have been synthesized by slow solvent evaporation technique and irradiated with 6 MeV electrons at fluences of 0.5 ×1015e /cm2 , 1.0 ×1015e /cm2 and 1.5 ×1015e /cm2 . The Powder X-ray Diffraction (PXRD) studies showed that the intensity of the diffraction peaks of the Electron Beam (EB) irradiated crystals decreases with irradiation fluence. The electron irradiation induced effects on the optical parameters such as cut-off wavelength, band gap, Urbach energy and refractive index have been studied and the results are tabulated. The electronic parameters such as valence electron plasma energy, ℏωp , Penn gap, Ep , Fermi energy, EF and Electronic polarizability, α for pure and irradiated LAMD crystals are calculated. The electrical and thermal properties of the pure and irradiated LAMD crystals are also investigated.

The Structure of Glycine Dihydrate: Implications for the Crystallization of Glycine from Solution and Its Structure in Outer Space

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Wenqian; Zhu, Qiang; Hu, Chunhua Tony

2017-01-18

Glycine, the simplest amino acid, is also the most polymorphous. Herein, we report the structure determination of an unknown phase of glycine which was firstly reported by Pyne and Suryanarayanan in 2001. To date, the new phase has only been prepared at 208 K as nanocrystals within ice. Through computational crystal structure prediction and powder X-ray diffraction methods, we identified this elusive phase as glycine dihydrate (GDH), representing a first report on a hydrated glycine structure. The structure of GDH has important implications for the state of glycine in aqueous solution, and the mechanisms of glycine crystallization. GDH may alsomore » be the form of glycine that comes to Earth from extraterrestrial sources.« less

Physicochemical characterization of mineral deposits in human ligamenta flava.

PubMed

Orzechowska, Sylwia; Wróbel, Andrzej; Kozieł, Marcin; Łasocha, Wiesław; Rokita, Eugeniusz

2018-05-01

The aim of our study was the detailed characterization of calcium deposits in ligamenta flava. The use of microcomputed tomography allowed extending the routine medical investigations to characterize mineral grains in the microscopic scale. A possible connection between spinal stenosis and ligament mineralization was investigated. The studies were carried out on 24 surgically removed ligamentum flavum samples divided into control and stenosis groups. Physicochemical characterization of the inorganic material was performed using X-ray fluorescence, X-ray diffraction, and Fourier transform infrared spectroscopy. The minerals were present in 14 of 24 ligament samples, both in stenosis and control groups. The inorganic substance constitutes on average ~0.1% of the sample volume. The minerals are scattered in the soft tissue matrix without any regular pattern. It was confirmed that minerals possess an internal structure and consist of the organic material and small inorganic grains mixture. The physicochemical analyses show that the predominant crystalline phase was hydroxyapatite (HAP). In the stenosis group calcium pyrophosphate dehydrate (CPPD) was identified. Both structures were never present in a single sample. Two different crystal structures suggest two independent processes of mineralization. The formation of CPPD may be treated as a more intense process since CPPD minerals are characterized by bigger values of the structural parameters and higher density than HAP deposits. The formation of HAP minerals is a soft tissue degeneration process that begins, in some cases, at early age or may not occur at all. Various density and volume of mineral grains indicate that the mineralization process does not occur in a constant environment and proceeds with various speeds. The formation of minerals in ligamenta flava is not directly associated with diagnosed spinal canal stenosis.

The Structure of Glycine Dihydrate: Implications for the Crystallization of Glycine from Solution and Its Structure in Outer Space.

PubMed

Xu, Wenqian; Zhu, Qiang; Hu, Chunhua Tony

2017-02-13

Glycine, the simplest amino acid, is also the most polymorphous. Herein, we report the structure determination of a long unknown phase of glycine, which was first reported by Pyne and Suryanarayanan in 2001. To date, this phase has only been prepared at 208 K as nanocrystals within ice. Through computational crystal-structure prediction and powder X-ray diffraction methods, we identified this elusive phase as glycine dihydrate (GDH), representing the first report on the structure of a hydrated glycine structure. The structure of GDH has important implications for the state of glycine in aqueous solution and the mechanisms of glycine crystallization. GDH may also be the form of glycine that comes to Earth from extraterrestrial sources. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Non linear optical studies on semiorganic single crystal: L-arginine 4-nitrophenalate 4-nitrophenol dihydrate (LAPP)

NASA Astrophysics Data System (ADS)

Mahadevan, M.; Sankar, P. K.; Vinitha, G.; Arivanandhan, M.; Ramachandran, K.; Anandan, P.

2017-07-01

L-arginine 4-nitrophenalate 4-nitrophenol dihydrate (LAPP) has been synthesized and grown by solution growth at room temperature using deionized water as a solvent. The various functional groups of the sample were identified by Fourier transform infra-red and Fourier transforms - Raman spectroscopic analyses. The Laser damage threshold of LAPP has been studied. Refractive index of LAPP single crystal was measured using Metricon prism coupler Instrument. The etching studies were carried out to study the quality of the grown crystals. The third order nonlinear optical properties of LAPP sample was analyzed by the Z-scan technique using 532 nm diode pumped CW Nd: YAG laser. The LAPP material exhibits negative optical nonlinearity. The results show that LAPP sample has potential applications in nonlinear optics and it can be exploited for optical limiting or switching.

Heterogeneous Nucleation of Dicalcium Phosphate Dihydrate on Modified Silica Surfaces

PubMed Central

Miller, Carrie; Komunjer, Ljepša; Hlady, Vladimir

2012-01-01

Heterogeneous nucleation of dicalcium phosphate dihydrate, CaHPO4•2H2O (DCPD) was studied on untreated planar fused silica and on three modified silica surfaces: octadecylsilyl (OTS) modified silica, human serum albumin treated OTS silica, and UV-oxidized 3-mercaptopropyltriethoxysilyl (MTS) modified silica. The supersaturation ratio of calcium and phosphate solution with respect to DCPD was kept below ~10. The nucleated crystals were observed 24 hours and one week after initial contact between supersaturated solutions and substrate surfaces using bright field and reflectance interference contrast microscopy. No DCPD crystals nucleated on albumin-treated OTS-silica. Majority of the DCDP crystals formed on the other modified silica surfaces appeared to be morphologically similar irrespective of the nature of nucleating substrate. Reflectance interference contrast microscopy provided a proof that the majority of the crystals on these substrates do not develop an extended contact with the substrate surface. The images showed that the most extended contact planes were between the DCPD crystals and MTS modified silica surface. The crystals nucleated on OTS-treated and untreated silica surfaces showed only few or none well-developed contact planes. PMID:25264399

Superposition model analysis of zero field splitting for Mn2+ in some host single crystals

NASA Astrophysics Data System (ADS)

Bansal, R. S.; Ahlawat, P.; Bharti, M.; Hooda, S. S.

2013-07-01

The Newman superposition model has been used to investigate the substitution of Mn2+ for Zn2+ site in ammonium tetra flurozincate dihydrate and for Co2+ site in cobalt ammonium phosphate hexahydrate and cobalt potassium phosphate hexahydrate single crystals. The calculated values of zero field splitting parameter b 2 0 at room temperature fit the experimental data with average intrinsic parameters overline{b}2 (F) = -0.0531 cm-1 for fluorine and overline{b}2 (O) = -0.0280 cm-1 for oxygen, taken t 2 = 7 for Mn2+ doped in ammonium tetra fluorozincate dihydrate single crystals. The values of overline{b}2 determined for Mn2+ doped in cobalt ammonium phosphate hexahydrate are -0.049 cm-1 for site I and -0.045 cm-1 for site II and in cobalt pottasium phosphate hexahydrate single crystals it is found to be overline{b}2 = -0.086 cm-1. We find close agreement between theoretical and experimental values of b 2 0.

7-Chloro-4-[(7-chloro­quinolin-4-yl)sulfan­yl]quinoline dihydrate

PubMed Central

Wardell, James L.; Tiekink, Edward R. T.

2012-01-01

In the title thio­ether dihydrate, C18H10Cl2N2S·2H2O, the S-bound quinolinyl residues are almost orthogonal, forming a dihedral angle of 72.36 (4)°. In the crystal, the four water mol­ecules are connected via an eight-membered {⋯OH}4 synthon with each of the four pendent water H atoms hydrogen bonded to a pyridine N atom to stabilize a three-dimensional architecture. PMID:22589973

Dehydration of trehalose dihydrate at low relative humidity and ambient temperature.

PubMed

Jones, Matthew D; Hooton, Jennifer C; Dawson, Michelle L; Ferrie, Alan R; Price, Robert

2006-04-26

The physico-chemical behaviour of trehalose dihydrate during storage at low relative humidity and ambient temperature was investigated, using a combination of techniques commonly employed in pharmaceutical research. Weight loss, water content determinations, differential scanning calorimetry and X-ray powder diffraction showed that at low relative humidity (0.1% RH) and ambient temperature (25 degrees C) trehalose dihydrate dehydrates forming the alpha-polymorph. Physical examination of trehalose particles by scanning electron microscopy and of the dominant growth faces of trehalose crystals by environmentally controlled atomic force microscopy revealed significant changes in surface morphology upon partial dehydration, in particular the formation of cracks. These changes were not fully reversible upon complete rehydration at 50% RH. These findings should be considered when trehalose dihydrate is used as a pharmaceutical excipient in situations where surface properties are key to behaviour, for example as a carrier in a dry powder inhalation formulations, as morphological changes under common processing or storage conditions may lead to variations in formulation performance.

Growth and characterization of Melaminium bis (trichloroacetate) dihydrate

NASA Astrophysics Data System (ADS)

Kanagathara, N.; Renganathan, N. G.; Marchewka, M. K.; Sivakumar, N.; Gayathri, K.; Krishnan, P.; Gunasekaran, S.; Anbalagan, G.

2013-01-01

Single crystals of melaminium bis (trichloroacetate) dihydrate have been grown successfully by slow evaporation solution growth technique at room temperature. Single crystal X-ray diffraction analysis reveals that the compound crystallizes in monoclinic system with non -centrosymmetric space group C2 with lattice parameters a = 17.70 Å, b = 8.44 Å, c = 6.09 Å, α = 90°, β = 100.24°, γ = 90° and V = 900 (Å)3. The UV-Vis transmittance spectrum shows that the crystal has a good optical transmittance in the entire visible region with lower cutoff wavelength of 351 nm. The vibrational frequencies of various functional groups present in the crystal have been derived from FI-IR, FT-Raman and Confocal Raman analyses. The chemical structure of the compound was established by 1H and 13C NMR spectrum. TGA-DTA analysis reveals that the materials have good thermal stability and the melting point of the crystal is found to be 195 °C. The dielectric response of the crystals was studied in the frequency range 50 Hz to 5 MHz at different temperatures and the results are discussed. Etching studies show the growth pattern of the crystals. The second harmonic generation efficiency was measured in comparison with KDP by employing powder Kurtz method.

Crystal structures of two solvates of (18-crown-6)potassium acetate.

PubMed

Liebing, Phil; Zaeni, Ahmad; Olbrich, Falk; Edelmann, Frank T

2016-12-01

The crystal and mol-ecular strutures of two solvated forms of [K(18 c 6)]OAc (18 c 6 = 18-crown-6 = 1,4,7,10,13,16-hexa-oxa-cyclo-octa-decane and OAc = acetate) were determined by single-crystal X-ray diffraction, namely (acetato-κ 2 O , O ')(1,4,7,10,13,16-hexa-oxa-cyclo-octa-decane-κ 6 O )potassium dihydrate, [K(CH 3 COO)(C 12 H 24 O 6 )]·2H 2 O ( 1 ) and (acetato-κ 2 O , O ')aqua-(1,4,7,10,13,16-hexa-oxa-cyclo-octa-decane-κ 6 O )potassium acetic acid monosolvate [K(CH 3 COO)(C 12 H 24 O 6 )(H 2 O)]·CH 3 COOH ( 2 ). In both compounds, the acetate anion is bonded to the potassium ion in a chelating fashion and the metal atom is consequently slightly displaced from the O 6 plane of the crown ether. In the crystals, O-H⋯O hydrogen bonds lead to a polymeric ladder structure in the dihydrate 1 , while the acetic acid hydrate 2 features inversion dimers.

"Fabrication of arbitrarily shaped carbonate apatite foam based on the interlocking process of dicalcium hydrogen phosphate dihydrate".

PubMed

Sugiura, Yuki; Tsuru, Kanji; Ishikawa, Kunio

2017-08-01

Carbonate apatite (CO 3 Ap) foam with an interconnected porous structure is highly attractive as a scaffold for bone replacement. In this study, arbitrarily shaped CO 3 Ap foam was formed from α-tricalcium phosphate (α-TCP) foam granules via a two-step process involving treatment with acidic calcium phosphate solution followed by hydrothermal treatment with NaHCO 3 . The treatment with acidic calcium phosphate solution, which is key to fabricating arbitrarily shaped CO 3 Ap foam, enables dicalcium hydrogen phosphate dihydrate (DCPD) crystals to form on the α-TCP foam granules. The generated DCPD crystals cause the α-TCP granules to interlock with each other, inducing an α-TCP/DCPD foam. The interlocking structure containing DCPD crystals can survive hydrothermal treatment with NaHCO 3 . The arbitrarily shaped CO 3 Ap foam was fabricated from the α-TCP/DCPD foam via hydrothermal treatment at 200 °C for 24 h in the presence of a large amount of NaHCO 3 .

Investigations on nucleation, HRXRD, optical, piezoelectric, polarizability and Z-scan analysis of L-arginine maleate dihydrate single crystals

NASA Astrophysics Data System (ADS)

Sakthy Priya, S.; Alexandar, A.; Surendran, P.; Lakshmanan, A.; Rameshkumar, P.; Sagayaraj, P.

2017-04-01

An efficient organic nonlinear optical single crystal of L-arginine maleate dihydrate (LAMD) has been grown by slow evaporation solution technique (SEST) and slow cooling technique (SCT). The crystalline perfection of the crystal was examined using high-resolution X-ray diffractometry (HRXRD) analysis. Photoluminescence study confirmed the optical properties and defects level in the crystal lattice. Electromechanical behaviour was observed using piezoelectric co-efficient (d33) analysis. The photoconductivity analysis confirmed the negative photoconducting nature of the material. The dielectric constant and loss were measured as a function of frequency with varying temperature and vice-versa. The laser damage threshold (LDT) measurement was carried out using Nd:YAG Laser with a wavelength of 1064 nm (Focal length is 35 cm) and the obtained results showed that LDT value of the crystal is high compared to KDP crystal. The high laser damage threshold of the grown crystal makes it a potential candidate for second and higher order nonlinear optical device application. The third order nonlinear optical parameters of LAMD crystal is determined by open-aperture and closed-aperture studies using Z-scan technique. The third order linear and nonlinear optical parameters such as the nonlinear refractive index (n2), two photon absorption coefficient (β), Real part (Reχ3) and imaginary part (Imχ3) of third-order nonlinear optical susceptibility are calculated.

Unusual calcium oxalate crystals in ethylene glycol poisoning.

PubMed

Godolphin, W; Meagher, E P; Sanders, H D; Frohlich, J

1980-06-01

A patient poisoned with ethylene glycol exhibited the symptoms of (1) hysteria, (2) metabolic acidosis with both a large anion gap and osmolal gap, and (3) crystalluria. However, the shape of the urinary crystals was prismatic and resembled hippurate rather than the expected dipyramidal calcium oxalate dihydrate. X-ray crystallography positively identified them as calcium oxalate monohydrate.

Unraveling Complexity in the Solid Form Screening of a Pharmaceutical Salt: Why so Many Forms? Why so Few?

PubMed Central

2017-01-01

The solid form landscape of 5-HT2a antagonist 3-(4-(benzo[d]isoxazole-3-yl)piperazin-1-yl)-2,2-dimethylpropanoic acid hydrochloride (B5HCl) proved difficult to establish. Many crystalline materials were produced by solid form screening, but few forms readily grew high quality crystals to afford a clear picture or understanding of the solid form landscape. Careful control of crystallization conditions, a range of experimental methods, computational modeling of solvate structures, and crystal structure prediction were required to see potential arrangements of the salt in its crystal forms. Structural diversity in the solid form landscape of B5HCl was apparent in the layer structures for the anhydrate polymorphs (Forms I and II), dihydrate and a family of solvates with alcohols. The alcohol solvates, which provided a distinct packing from the neat forms and the dihydrate, form layers with conserved hydrogen bonding between B5HCl and the solvent, as well as stacking of the aromatic rings. The ability of the alcohol hydrocarbon moieties to efficiently pack between the layers accounted for the difficulty in growing some solvate crystals and the inability of other solvates to crystallize altogether. Through a combination of experiment and computation, the crystallization problems, form stability, and desolvation pathways of B5HCl have been rationalized at a molecular level. PMID:29018305

Distillation Kinetics of Solid Mixtures of Hydrogen Peroxide and Water and the Isolation of Pure Hydrogen Peroxide in Ultrahigh Vacuum

NASA Technical Reports Server (NTRS)

Teolis, B. D.; Baragiola, R. A.

2006-01-01

We present results of the growth of thin films of crystalline H2O2 and H2O2.2H2O (dihydrate) in ultrahigh vacuum by distilling an aqueous solution of hydrogen peroxide. We traced the process using infrared reflectance spectroscopy, mass loss on a quartz crystal microbalance, and in a few cases ultraviolet-visible reflectance. We find that the different crystalline phases-water, dihydrate, and hydrogen peroxide-have very different sublimation rates, making distillation efficient to isolate the less volatile component, crystalline H2O2.

Crystal water dynamics of guanosine dihydrate: analysis of atomic displacement parameters, time profile of hydrogen-bonding probability, and translocation of water by MD simulation.

PubMed

Yoneda, Shigetaka; Sugawara, Yoko; Urabe, Hisako

2005-01-27

The dynamics of crystal water molecules of guanosine dihydrate are investigated in detail by molecular dynamics (MD) simulation. A 2 ns simulation is performed using a periodic boundary box composed of 4 x 5 x 8 crystallographic unit cells and using the particle-mesh Ewald method for calculation of electrostatic energy. The simulated average atomic positions and atomic displacement parameters are remarkably coincident with the experimental values determined by X-ray analysis, confirming the high accuracy of this simulation. The dynamics of crystal water are analyzed in terms of atomic displacement parameters, orientation vectors, order parameters, self-correlation functions of the orientation vectors, time profiles of hydrogen-bonding probability, and translocations. The simulation clarifies that the average structure is composed of various stable and transient structures of the molecules. The simulated guanosine crystal forms a layered structure, with four water sites per asymmetric unit, classified as either interlayer water or intralayer water. From a detailed analysis of the translocations of water molecules in the simulation, columns of intralayer water molecules along the c axis appear to represent a pathway for hydration and dehydration by a kind of molecular valve mechanism.

Novel ANKH Amino Terminus Mutation (Pro5Ser) Associated With Early-Onset Calcium Pyrophosphate Disease With Associated Phosphaturia

PubMed Central

Gruber, Barry L.; Couto, Ana Rita; Armas, Jácome Bruges; Brown, Matthew A.; Finzel, Kathleen; Terkeltaub, Robert A.

2015-01-01

This report describes a 32-year-old woman presenting since childhood with progressive calcium pyrophosphate disease (CPPD), characterized by severe arthropathy and chondrocalcinosis involving multiple peripheral joints and intervertebral disks. Because ANKH mutations have been previously described in familial CPPD, the proband’s DNA was assessed at this locus by direct sequencing of promoter and coding regions and revealed 3 sequence variants in ANKH. Sequences of exon 1 revealed a novel isolated nonsynonymous mutation (c.13 C>T), altering amino acid in codon 5 from proline to serine (CCG>TCG). Sequencing of parental DNA revealed an identical mutation in the proband’s father but not the mother. Subsequent clinical evaluation demonstrated extensive chondrocalcinosis and degenerative arthropathy in the proband’s father. In summary, we report a novel mutation, not previously described, in ANKH exon 1, wherein serine replaces proline, in a case of early-onset severe CPPD associated with metabolic abnormalities, with similar findings in the proband’s father. PMID:22647861

Novel ANKH amino terminus mutation (Pro5Ser) associated with early-onset calcium pyrophosphate disease with associated phosphaturia.

PubMed

Gruber, Barry L; Couto, Ana Rita; Armas, Jácome Bruges; Brown, Matthew A; Finzel, Kathleen; Terkeltaub, Robert A

2012-06-01

This report describes a 32-year-old woman presenting since childhood with progressive calcium pyrophosphate disease (CPPD), characterized by severe arthropathy and chondrocalcinosis involving multiple peripheral joints and intervertebral disks. Because ANKH mutations have been previously described in familial CPPD, the proband's DNA was assessed at this locus by direct sequencing of promoter and coding regions and revealed 3 sequence variants in ANKH. Sequences of exon 1 revealed a novel isolated nonsynonymous mutation (c.13 C>T), altering amino acid in codon 5 from proline to serine (CCG>TCG). Sequencing of parental DNA revealed an identical mutation in the proband's father but not the mother. Subsequent clinical evaluation demonstrated extensive chondrocalcinosis and degenerative arthropathy in the proband's father. In summary, we report a novel mutation, not previously described, in ANKH exon 1, wherein serine replaces proline, in a case of early-onset severe CPPD associated with metabolic abnormalities, with similar findings in the proband's father.

Modulation of calcium oxalate dihydrate growth by selective crystal-face binding of phosphorylated osteopontin and polyaspartate peptide showing occlusion by sectoral (compositional) zoning.

PubMed

Chien, Yung-Ching; Masica, David L; Gray, Jeffrey J; Nguyen, Sarah; Vali, Hojatollah; McKee, Marc D

2009-08-28

Calcium oxalate dihydrate (COD) mineral and the urinary protein osteopontin/uropontin (OPN) are commonly found in kidney stones. To investigate the effects of OPN on COD growth, COD crystals were grown with phosphorylated OPN or a polyaspartic acid-rich peptide of OPN (DDLDDDDD, poly-Asp(86-93)). Crystals grown with OPN showed increased dimensions of the {110} prismatic faces attributable to selective inhibition at this crystallographic face. At high concentrations of OPN, elongated crystals with dominant {110} faces were produced, often with intergrown, interpenetrating twin crystals. Poly-Asp(86-93) dose-dependently elongated crystal morphology along the {110} faces in a manner similar to OPN. In crystal growth studies using fluorescently tagged poly-Asp(86-93) followed by imaging of crystal interiors using confocal microscopy, sectoral (compositional) zoning in COD was observed resulting from selective binding and incorporation (occlusion) of peptide exclusively into {110} crystal sectors. Computational modeling of poly-Asp(86-93) adsorption to COD {110} and {101} surfaces also suggests increased stabilization of the COD {110} surface and negligible change to the natively stable {101} surface. Ultrastructural, colloidal-gold immunolocalization of OPN by transmission electron microscopy in human stones confirmed an intracrystalline distribution of OPN. In summary, OPN and its poly-Asp(86-93) sequence similarly affect COD mineral growth; the {110} crystallographic faces become enhanced and dominant attributable to {110} face inhibition by the protein/peptide, and peptides can incorporate into the mineral phase. We, thus, conclude that the poly-Asp(86-93) domain is central to the OPN ability to interact with the {110} faces of COD, where it binds to inhibit crystal growth with subsequent intracrystalline incorporation (occlusion).

Crystal growth and DFT insight on sodium para-nitrophenolate para-nitrophenol dihydrate single crystal for NLO applications

NASA Astrophysics Data System (ADS)

Selvakumar, S.; Boobalan, Maria Susai; Anthuvan Babu, S.; Ramalingam, S.; Leo Rajesh, A.

2016-12-01

Single crystals of sodium para-nitrophenolate para-nitrophenol dihydrate (SPPD) were grown by slow evaporation technique and its structure has been studied by FT-IR, FT-Raman and single crystal X-ray diffraction techniques. The optical and electrical properties were characterized by UV-Vis spectrum, and dielectric studies respectively. SPPD was thermally stable up to 128 °C as determined by TG-DTA curves. Using the Kurtz-Perry powder method, the second-harmonic generation efficiency was found to be five times to that of KDP. Third-order nonlinear response was studied using Z-scan technique with a He-Ne laser (632.8 nm) and NLO parameters such as intensity dependent refractive index, nonlinear absorption coefficient and third-order susceptibility were also estimated. The molecular geometry from X-ray experiment in the ground state has been compared using density functional theory (DFT) with appropriate basis set. The first-order hyperpolarizability also calculated using DFT approaches. Stability of the molecule arising from hyperconjugative interactions leading to its nonlinear optical activity and charge delocalization were analyzed using natural bond orbital technique. HOMO-LUMO energy gap value suggests the possibility of charge transfer within the molecule. Based on optimized ground state geometries, Natural bond orbital (NBO) analysis was performed to study donor-acceptor interactions.

Elemental distribution analysis of urinary crystals.

PubMed

Fazil Marickar, Y M; Lekshmi, P R; Varma, Luxmi; Koshy, Peter

2009-10-01

Various crystals are seen in human urine. Some of them, particularly calcium oxalate dihydrate, are seen normally. Pathological crystals indicate crystal formation initiating urinary stones. Unfortunately, many of the relevant crystals are not recognized in light microscopic analysis of the urinary deposit performed in most of the clinical laboratories. Many crystals are not clearly identifiable under the ordinary light microscopy. The objective of the present study was to perform scanning electron microscopic (SEM) assessment of various urinary deposits and confirm the identity by elemental distribution analysis (EDAX). 50 samples of urinary deposits were collected from urinary stone clinic. Deposits containing significant crystalluria (more than 10 per HPF) were collected under liquid paraffin in special containers and taken up for SEM studies. The deposited crystals were retrieved with appropriate Pasteur pipettes, and placed on micropore filter paper discs. The fluid was absorbed by thicker layers of filter paper underneath and discs were fixed to brass studs. They were then gold sputtered to 100 A and examined under SEM (Jeol JSM 35C microscope). When crystals were seen, their morphology was recorded by taking photographs at different angles. At appropriate magnification, EDAX probe was pointed to the crystals under study and the wave patterns analyzed. Components of the crystals were recognized by utilizing the data. All the samples analyzed contained significant number of crystals. All samples contained more than one type of crystal. The commonest crystals encountered included calcium oxalate monohydrate (whewellite 22%), calcium oxalate dihydrate (weddellite 32%), uric acid (10%), calcium phosphates, namely, apatite (4%), brushite (6%), struvite (6%) and octocalcium phosphate (2%). The morphological appearances of urinary crystals described were correlated with the wavelengths obtained through elemental distribution analysis. Various urinary crystals that are not reported under light microscopy could be recognized by SEM-EDAX combination. EDAX is a significant tool for recognizing unknown crystals not identified by ordinary light microscopy or SEM alone.

Studies on the syntheses, structural characterization, antimicrobial-, and DPPH radical scavenging activity of the cocrystals caffeine:cinnamic acid and caffeine:eosin dihydrate

NASA Astrophysics Data System (ADS)

Suresh Kumar, G. S.; Seethalakshmi, P. G.; Bhuvanesh, N.; Kumaresan, S.

2013-10-01

Two organic cocrystals namely, caffeine:cinnamic acid [(caf)(ca)] (1) and caffeine:eosin dihydrate [(caf)(eos)]·2H2O (2) were synthesized and studied by FT-IR, TGA/DTA, and single crystal XRD. The crystal system of cocrystal 1 is triclinic with space group P-1 and Z = 2 and that of cocrystal 2 is monoclinic with space group P21/C and Z = 4. An imidazole-carboxylic acid synthon is observed in the cocrystal 1. The intermolecular hydrogen bond, O-H⋯N and π-π interactions play a major role in stabilizing 1 whereas the intermolecular hydrogen bonds, O-H⋯O, O-H⋯N, and intramolecular hydrogen bond, O-H⋯Br; along with π-π interactions together play a vital role in stabilizing the structure of 2. The antimicrobial- and DPPH radical scavenging activities of both the cocrystals were studied.

N-(L-2-aminopentanoyl)-L-phenylalanine dihydrate, a hydrophobic dipeptide with a nonproteinogenic residue.

PubMed

Görbitz, Carl Henrik; Yadav, Vitthal N

2013-09-01

The title dipeptide, better known as L-norvalyl-L-phenylalanine {systematic name: (S)-2-[(S)-2-aminopentanamido]-3-phenylpropanoic acid dihydrate}, C14H20N2O3·2H2O, has a nonproteinogenic N-terminal residue. In the solid state, it takes on a molecular conformation typical for one of the three classes of nanoporous dipeptides, but like two related compounds with a hydrophobic N-terminal residue and a C-terminal L-phenylalanine, it fails to form channels or pores. Instead, the crystal structure is divided into distinct hydrophobic and hydrophilic layers, the latter encompassing cocrystallized water molecules connecting the charged N- and C-terminal groups.

Spatial Distribution of Trehalose Dihydrate Crystallization in Tablets by X-ray Diffractometry.

PubMed

Thakral, Naveen K; Yamada, Hiroyuki; Stephenson, Gregory A; Suryanarayanan, Raj

2015-10-05

Crystallization of trehalose dihydrate (C12H22O11·2H2O) was induced by storing tablets of amorphous anhydrous trehalose (C12H22O11) at 65% RH (RT). Our goal was to evaluate the advantages and limitations of two approaches of profiling spatial distribution of drug crystallization in tablets. The extent of crystallization, as a function of depth, was determined in tablets stored for different time-periods. The first approach was glancing angle X-ray diffractometry, where the penetration depth of X-rays was modulated by the incident angle. Based on the mass attenuation coefficient of the matrix, the depth of X-ray penetration was calculated as a function of incident angle, which in turn enabled us to "calculate" the extent of crystallization to different depths. In the second approach, the tablets were split into halves and the split surfaces were analyzed directly. Starting from the tablet surface and moving toward the midplane, XRD patterns were collected in 36 "regions", in increments of 0.05 mm. The results obtained by the two approaches were, in general, in good agreement. Additionally, the results obtained were validated by determining the "average" crystallization in the entire tablet by using synchrotron radiation in the transmission mode. The glancing angle method could detect crystallization up to ∼650 μm and had a "surface bias". Being a nondestructive technique, this method will permit repeated analyses of the same tablet at different time points, for example, during a stability study. However, split tablet analyses, while a "destructive" technique, provided comprehensive and unbiased depth profiling information.

Synthesis of calcium oxalate crystals in culture medium irradiated with non-equilibrium atmospheric-pressure plasma

NASA Astrophysics Data System (ADS)

Kurake, Naoyuki; Tanaka, Hiromasa; Ishikawa, Kenji; Nakamura, Kae; Kajiyama, Hiroaki; Kikkawa, Fumitaka; Mizuno, Masaaki; Yamanishi, Yoko; Hori, Masaru

2016-09-01

Octahedral particulates several tens of microns in size were synthesized in a culture medium irradiated through contact with a plume of non-equilibrium atmospheric-pressure plasma (NEAPP). The particulates were identified in the crystalline phase as calcium oxalate dihydrate (COD). The original medium contained constituents such as NaCl, d-glucose, CaCl2, and NaHCO3 but not oxalate or oxalic acid. The oxalate was clearly synthesized and crystallized in the medium as thermodynamically unstable COD crystals after the NEAPP irradiation.

Reinjury risk of nano-calcium oxalate monohydrate and calcium oxalate dihydrate crystals on injured renal epithelial cells: aggravation of crystal adhesion and aggregation

PubMed Central

Gan, Qiong-Zhi; Sun, Xin-Yuan; Bhadja, Poonam; Yao, Xiu-Qiong; Ouyang, Jian-Ming

2016-01-01

Background Renal epithelial cell injury facilitates crystal adhesion to cell surface and serves as a key step in renal stone formation. However, the effects of cell injury on the adhesion of nano-calcium oxalate crystals and the nano-crystal-induced reinjury risk of injured cells remain unclear. Methods African green monkey renal epithelial (Vero) cells were injured with H2O2 to establish a cell injury model. Cell viability, superoxide dismutase (SOD) activity, malonaldehyde (MDA) content, propidium iodide staining, hematoxylin–eosin staining, reactive oxygen species production, and mitochondrial membrane potential (Δψm) were determined to examine cell injury during adhesion. Changes in the surface structure of H2O2-injured cells were assessed through atomic force microscopy. The altered expression of hyaluronan during adhesion was examined through laser scanning confocal microscopy. The adhesion of nano-calcium oxalate monohydrate (COM) and calcium oxalate dihydrate (COD) crystals to Vero cells was observed through scanning electron microscopy. Nano-COM and COD binding was quantitatively determined through inductively coupled plasma emission spectrometry. Results The expression of hyaluronan on the cell surface was increased during wound healing because of Vero cell injury. The structure and function of the cell membrane were also altered by cell injury; thus, nano-crystal adhesion occurred. The ability of nano-COM to adhere to the injured Vero cells was higher than that of nano-COD crystals. The cell viability, SOD activity, and Δψm decreased when nano-crystals attached to the cell surface. By contrast, the MDA content, reactive oxygen species production, and cell death rate increased. Conclusion Cell injury contributes to crystal adhesion to Vero cell surface. The attached nano-COM and COD crystals can aggravate Vero cell injury. As a consequence, crystal adhesion and aggregation are enhanced. These findings provide further insights into kidney stone formation. PMID:27382277

Crystallization of dicalcium phosphate dihydrate with presence of glutamic acid and arginine at 37 °C.

PubMed

Li, Chengfeng; Ge, Xiaolu; Li, Guochang; Bai, Jiahai; Ding, Rui

2014-08-01

The formations of non-metabolic stones, bones and teeth were seriously related to the morphology, size and surface reactivity of dicalcium phosphate dihydrate (DCPD). Herein, a facile biomimetic mineralization method with presence of glutamic acid and arginine was employed to fabricate DCPD with well-defined morphology and adjustable crystallite size. In reaction solution containing more arginine, crystallization of DCPD occurred with faster rate of nucleation and higher density of stacked layers due to the generation of more OH(-) ions after hydrolysis of arginine at 37 °C. With addition of fluorescein or acetone, the consumption of OH(-) ions or desolvation reaction of Ca(2+) ions was modulated, which resulted in the fabrication of DCPD with adjustable crystallite sizes and densities of stacked layers. In comparison with fluorescein-loading DCPD, dicalcium phosphate anhydrate was prepared with enhanced photoluminescence properties due to the reduction of self-quenching effect and regular arrangement of encapsulated fluorescein molecules. With addition of more acetone, DCPD was prepared with smaller crystallite size via antisolvent crystallization. The simulated process with addition of amino acids under 37 °C would shed light on the dynamic process of biomineralization for calcium phosphate compounds. Copyright © 2014 Elsevier B.V. All rights reserved.

4′,5-Dihy­droxy-7-meth­oxy­flavanone dihydrate

PubMed Central

Brito, Iván; Bórquez, Jorge; Simirgiotis, Mario; Cárdenas, Alejandro; López-Rodríguez, Matías

2012-01-01

The title compound, C16H14O5·2H2O [systematic name: 5-hy­droxy-2-(4-hy­droxy­phen­yl)-7-meth­oxy­chroman-4-one dihydrate], is a natural phytoalexin flavone isolated from the native chilean species Heliotropium taltalense and crystallizes with an organic mol­ecule and two water mol­ecules in the asymmetric unit. The 5-hy­droxy group forms a strong intra­molecular hydrogen bond with the carbonyl group, resulting in a six-membered ring. In the crystal, the components are linked by O—H⋯O hydrogen bonds, forming a three-dimensional network. The 4-hy­droxy­phenyl benzene ring is bonded equatorially to the pyrone ring, which adopts a slightly distorted sofa conformation. The title compound is the hydrated form of a previously reported structure [Shoja (1990 ▶). Acta Cryst. C46, 1969–1971]. There are only slight variations in the mol­ecular geometry between the two compounds. PMID:22259537

Communication Platform Payload Definition (CPPD) study. Volume 2: Technical report

NASA Technical Reports Server (NTRS)

Hunter, E. M.; Driggers, T.; Jorasch, R.

1986-01-01

This is Volume 2 (Technical Report) of the Ford Aerospace & Communications Corporation Final Report for the Communication Platform Payload Definition (CPPD) Study program conducted for NASA Lewis Research Center under contract No. NAS3-24235. This report presents the results of the study effort leading to five potential platform payloads to service CONUS and WARC Region 2 traffic demand as projected to the year 2008. The report addresses establishing the data bases, developing service aggregation scenarios, selecting and developing 5 payload concepts, performing detailed definition of the 5 payloads, costing them, identifying critical technology, and finally comparing the payloads with each other and also with non-aggregated equivalent services.

Communication Platform Payload Definition (CPPD) study. Volume 1: Executive summary

NASA Technical Reports Server (NTRS)

Hunter, E. M.

1986-01-01

This is Volume 1 (Executive Summary) of the Ford Aerospace & Communications Corporation Final Report for the Communication Platform Payload Definition (CPPD) Study program conducted for NASA Lewis Research Center under contract No. NAS3-24235. This report presents the results of the study effort leading to five potential platform payloads to service CONUS and WARC Region 2 traffic demand as projected to the year 2008. The report addresses establishing the data bases, developing service aggregation scenarios, selecting and developing 5 payload concepts, performing detailed definition of the 5 payloads, costing them, identifying critical technology, and finally comparing the payloads with each other and also with non-aggregated equivalent services.

Communication Platform Payload Definition (CPPD) study. Volume 3: Addendum

NASA Technical Reports Server (NTRS)

Hunter, E. M.; Driggers, T.; Jorasch, R.

1986-01-01

This is Volume 3 (Addendum) of the Ford Aerospace & Communications Corporation Final Report for the Communication Platform Payload Definition (CPPD) Study Program conducted for NASA Lewis Research Center under contract No. NAS3-24235. This report presents the results of the study effort leading to five potential platform payloads to service CONUS and WARC Region 2 traffic demand as projected to the year 2008. The report addresses establishing the data bases, developing service aggregation scenarios, selecting and developing 5 payload concepts, performing detailed definition of the 5 payloads, costing them, identifying critical technology, and finally comparing the payloads with each other and also with non-aggregated equivalent services.

Transperineal Ultrasound as a Tool to Plan Surgical Strategies in Pediatric Urology: Back to the Future?

PubMed

de Jesus, Lisieux Eyer; Fazecas, Tatiana; Ribeiro, Bianca G; Dekermacher, Samuel

2017-06-01

To demonstrate the usefulness and advantages of transperineal ultrasound (TPUS) on planning the surgical tactics to treat childhood pelviperineal disease (CPPD). A cohort of CPPD is reviewed to provide a pictorial review of TPUS as imaging method variety of CPPD. Other imaging methods are compared with TPUS. TPUS studies of patients showing different conditions on the spectrum of pelviperineal malformation are shown in detail (pictorial review, graphically shown-see figures in the article and as supplementary material), highlighting the advantages of the method and comparing TPUS findings with other imaging techniques. Magnetic resonance imaging, contrast genitograms, voiding cystourethrography, and genital or urologic endoscopy have some important disadvantages, especially radiation exposure, high cost, not easily available equipment, and the need of general anesthesia or deep sedation in children. TPUS is easily available, including in impoverished environments, portable, painless, reproducible, inexpensive, and capable of providing detailed and specific information about pelviperineal malformation with accuracy. Data provided by TPUS are comparable with other imaging techniques (Table 1). Its main disadvantage is the dependency on the expertise of the operator to obtain high-quality, well-interpreted images. Copyright © 2017 Elsevier Inc. All rights reserved.

Crystallization and identification of the glycosylated moieties of two isoforms of the main allergen Hev b 2 and preliminary X-ray analysis of two polymorphs of isoform II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fuentes-Silva, D.; Mendoza-Hernández, G.; Stojanoff, V.

2007-09-01

Crystallization of important glycoenzymes involved in IgE-mediated latex allergy. Latex from Hevea brasiliensis contains several allergenic proteins that are involved in type I allergy. One of them is Hev b 2, which is a β-1,3-glucanase enzyme that exists in different isoforms with variable glycosylation content. Two glucanase isoforms were isolated from trees of the GV-42 clone by gel filtration, affinity and ion-exchange chromatography. Isoform I had a carbohydrate content of about 20%, with N-linked N-acetyl-glucosamine, N-acetyl-galactosamine, fucose and galactose residues as the main sugars, while isoform II showed 6% carbohydrate content constisting of N-acetyl-glucosamine, fucose, mannose and xylose. Both isoformsmore » were crystallized by the hanging-drop vapour-diffusion method. Isoform I crystals were grown using 0.2 M trisodium citrate dihydrate, 0.1 M Na HEPES pH 7.5 and 20%(v/v) 2-propanol, but these crystals were not appropriate for data collection. Isoform II crystals were obtained under two conditions and X-ray diffraction data were collected from both. In the first condition (0.2 M trisodium citrate, 0.1 M sodium cacodylate pH 6.5, 30% 2-propanol), crystals belonging to the tetragonal space group P4{sub 1} with unit-cell parameters a = b = 150.17, c = 77.41 Å were obtained. In the second condition [0.2 M ammonium acetate, 0.1 M trisodium citrate dihydrate pH 5.6, 30%(w/v) polyethylene glycol 4000] the isoform II crystals belonged to the monoclinic space group P2{sub 1}, with unit-cell parameters a = 85.08, b = 89.67, c = 101.80 Å, β = 113.6°. Preliminary analysis suggests that there are four molecules of isoform II in both asymmetric units.« less

Bulk growth of <001> organic nonlinear optical (NLO) L-arginine 4-nitrophenolate 4-nitrophenol dihydrate (LAPP) single crystals by SR method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pandian, Muthu Senthil, E-mail: senthilpandianm@ssn.edu.in; Sivasubramani, V.; Ramasamy, P.

2015-06-24

A transparent uniaxial L-arginine 4-nitrophenolate 4-nitrophenol dehydrate (LAPP) single crystal having dimension of 20 mm diameter and 45 mm length was grown by Sankaranarayanan-Ramasamy (SR) method with a growth rate of 1 mm per day. Using an identical solution the conventional crystal grown to a dimension of 8×5×5 mm{sup 3} was obtained over a period of 30 days. The crystal structure has been confirmed by single crystal X-ray diffraction measurement. The crystalline perfection of LAPP crystals grown by slow evaporation solution technique (SEST) and SR method were characterized using Vickers microhardness, UV-Vis NIR, chemical etching, dark and photo current measurements. The above study indicatesmore » that the crystal quality of the Sankaranarayanan-Ramasamy (SR) method grown LAPP is good compared to the conventional method grown crystal.« less

A study of the piezoelectric resonance in metal organic NLO single crystals: Sodium D-isoascorbate monohydrate and Lithium L-ascorbate dihydrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Saripalli, Ravi Kiran, E-mail: rksaripalli@physics.iisc.ernet.in; Sanath Kumar, R.; Elizabeth, Suja

2016-05-06

Large single crystals of Sodium D-isoacsorbate monohydrate and Lithium L-ascorbate dehydrate were grown using solution growth technique. Dielectric constant and dielectric loss were monitored as a function of frequency at different temperatures. These are typically characterized by strong resonance peaks. The piezoelectric coefficients d{sub 31}, elastic coefficient (S{sub 11}) and electromechanical coupling coefficient (k{sub 31}) were estimated by resonance-antiresonance method. The temperature dependence of the resonance-peaks frequencies was studied.

High variability of the heterogeneous ice nucleation potential of oxalic acid dihydrate and sodium oxalate

NASA Astrophysics Data System (ADS)

Wagner, R.; Möhler, O.; Saathoff, H.; Schnaiter, M.; Leisner, T.

2010-04-01

The heterogeneous ice nucleation potential of airborne oxalic acid dihydrate and sodium oxalate particles in the deposition and condensation mode has been investigated by controlled expansion cooling cycles in the AIDA aerosol and cloud chamber of the Karlsruhe Institute of Technology at temperatures between 244 and 228 K. Previous laboratory studies have highlighted the particular role of oxalic acid dihydrate as the only species amongst a variety of other investigated dicarboxylic acids to be capable of acting as a heterogeneous ice nucleus in both the deposition and immersion mode. We could confirm a high deposition mode ice activity for 0.03 to 0.8 μm sized oxalic acid dihydrate particles that were either formed by nucleation from a gaseous oxalic acid/air mixture or by rapid crystallisation of highly supersaturated aqueous oxalic acid solution droplets. The critical saturation ratio with respect to ice required for deposition nucleation was found to be less than 1.1 and the size-dependent ice-active fraction of the aerosol population was in the range from 0.1 to 22%. In contrast, oxalic acid dihydrate particles that had crystallised from less supersaturated solution droplets and had been allowed to slowly grow in a supersaturated environment from still unfrozen oxalic acid solution droplets over a time period of several hours were found to be much poorer heterogeneous ice nuclei. We speculate that under these conditions a crystal surface structure with less-active sites for the initiation of ice nucleation was generated. Such particles partially proved to be almost ice-inactive in both the deposition and condensation mode. At times, the heterogeneous ice nucleation ability of oxalic acid dihydrate significantly changed when the particles had been processed in preceding cloud droplet activation steps. Such behaviour was also observed for the second investigated species, namely sodium oxalate. Our experiments address the atmospheric scenario that coating layers of oxalic acid or its salts may be formed by physical and chemical processing on pre-existing particulates such as mineral dust and soot. Given the broad diversity of the observed heterogeneous ice nucleability of the oxalate species, it is not straightforward to predict whether an oxalate coating layer will improve or reduce the ice nucleation ability of the seed aerosol particles.

High variability of the heterogeneous ice nucleation potential of oxalic acid dihydrate and sodium oxalate

NASA Astrophysics Data System (ADS)

Wagner, R.; Möhler, O.; Saathoff, H.; Schnaiter, M.; Leisner, T.

2010-08-01

The heterogeneous ice nucleation potential of airborne oxalic acid dihydrate and sodium oxalate particles in the deposition and condensation mode has been investigated by controlled expansion cooling cycles in the AIDA aerosol and cloud chamber of the Karlsruhe Institute of Technology at temperatures between 244 and 228 K. Previous laboratory studies have highlighted the particular role of oxalic acid dihydrate as the only species amongst a variety of other investigated dicarboxylic acids to be capable of acting as a heterogeneous ice nucleus in both the deposition and immersion mode. We could confirm a high deposition mode ice activity for 0.03 to 0.8 μm sized oxalic acid dihydrate particles that were either formed by nucleation from a gaseous oxalic acid/air mixture or by rapid crystallisation of highly supersaturated aqueous oxalic acid solution droplets. The critical saturation ratio with respect to ice required for deposition nucleation was found to be less than 1.1 and the size-dependent ice-active fraction of the aerosol population was in the range from 0.1 to 22%. In contrast, oxalic acid dihydrate particles that had crystallised from less supersaturated solution droplets and had been allowed to slowly grow in a supersaturated environment from still unfrozen oxalic acid solution droplets over a time period of several hours were found to be much poorer heterogeneous ice nuclei. We speculate that under these conditions a crystal surface structure with less-active sites for the initiation of ice nucleation was generated. Such particles partially proved to be almost ice-inactive in both the deposition and condensation mode. At times, the heterogeneous ice nucleation ability of oxalic acid dihydrate significantly changed when the particles had been processed in preceding cloud droplet activation steps. Such behaviour was also observed for the second investigated species, namely sodium oxalate. Our experiments address the atmospheric scenario that coating layers of oxalic acid or its salts may be formed by physical and chemical processing on pre-existing particulates such as mineral dust and soot. Given the broad diversity of the observed heterogeneous ice nucleability of the oxalate species, it is not straightforward to predict whether an oxalate coating layer will improve or reduce the ice nucleation ability of the seed aerosol particles.

Evolution of molecular crystal optical phonons near structural phase transitions

NASA Astrophysics Data System (ADS)

Michki, Nigel; Niessen, Katherine; Xu, Mengyang; Markelz, Andrea

Molecular crystals are increasingly important photonic and electronic materials. For example organic semiconductors are lightweight compared to inorganic semiconductors and have inexpensive scale up processing with roll to roll printing. However their implementation is limited by their environmental sensitivity, in part arising from the weak intermolecular interactions of the crystal. These weak interactions result in optical phonons in the terahertz frequency range. We examine the evolution of intermolecular interactions near structural phase transitions by measuring the optical phonons as a function of temperature and crystal orientation using terahertz time-domain spectroscopy. The measured orientation dependence of the resonances provides an additional constraint for comparison of the observed spectra with the density functional calculations, enabling us to follow specific phonon modes. We observe crystal reorganization near 350 K for oxalic acid as it transforms from dihydrate to anhydrous form. We also report the first THz spectra for the molecular crystal fructose through its melting point.

Molecular structure, vibrational spectra and DFT computational studies of melaminium N-acetylglycinate dihydrate

NASA Astrophysics Data System (ADS)

Tanak, H.; Pawlus, K.; Marchewka, M. K.

2016-10-01

Melaminium N-acetylglycinate dihydrate, an organic material has been synthesized and characterized by X-ray diffraction, FT-IR, and FT-Raman spectroscopies for the protiated and deuteriated crystals. The title complex crystallizes in the triclinic system, and the space group is P-1 with a = 5.642(1) Å, b = 7.773(2) Å, c = 15.775(3) Å, α = 77.28(1)°, β = 84.00(1)°, γ = 73.43(1)° and Z = 2. The molecular geometry, vibrational frequencies and intensity of the vibrational bands have been interpreted with the aid of structure optimization based on density functional method (B3LYP) with the 6-311++G(d,p) basis set. The obtained vibrational wavenumbers and optimized geometric parameters were seen to be in good agreement with the experimental data. The intermolecular hydrogen bonding interactions of the title compound have been investigated using the natural bonding orbital analysis. It reveals that the O-H···O, N-H···N and N-H···O intermolecular interactions significantly influence crystal packing of this molecule. The non-linear optical properties are also addressed theoretically. The predicted NLO properties of the title compound are much greater than ones of urea. In addition, DFT calculations of the title compound, molecular electrostatic potential, thermodynamic properties, frontier orbitals and chemical reactivity descriptors were also performed at 6-311++G(d,p) level of theory.

Calcium Pyrophosphate Deposition (CPPD)

MedlinePlus

... Keep me signed in Passwords are Case Sensitive. Ex. Enter smith as follows: Smith Forgot Username/Password? ... Erythematosus (Juvenile) Takayasu's Arteritis Tendinitis & Bursitis Tumor Necrosis Factor Receptor Associated Periodic Syndrome (Juvenile) Vasculitis Enfermedades y ...

Effect of Mg2+ on acidic calcium phosphate phases grown by electrodeposition

NASA Astrophysics Data System (ADS)

Correia, Matheus Bento; Júnior, José Pedro Gualberto; Macedo, Michelle Cardinale S. S.; Resende, Cristiane Xavier; dos Santos, Euler Araujo

2017-10-01

In this work, the effect of Mg2+ ions on the electrodeposition of dicalcium phosphate dihydrate (DCPD), octacalcium phosphate (OCP) and calcium-deficient hydroxyapatite (CDHA) crystals on a commercially pure titanium (cp-Ti) substrate was evaluated. We demonstrated that Mg2+ ions could change the morphology of the coatings by inhibiting the growth rate of the OCP and CDHA crystals and diminishing the crystallite size of DCPD. The inhibition effect on OCP and CDHA was most likely due to a surface adsorption mechanism since no evidence of a doping process was observed using Rietveld refinement and electron diffraction analyses. Conversely, the presence of Mg2+ ions generated a favorable condition for the nucleation of a new Mg2+-rich DCPD crystal population, presenting smaller crystallite sizes.

Pharmacokinetics of ibuprofen sodium dihydrate and gastrointestinal tolerability of short-term treatment with a novel, rapidly absorbed formulation.

PubMed

Sörgel, F; Fuhr, U; Minic, M; Siegmund, M; Maares, J; Jetter, A; Kinzig-Schippers, M; Tomalik-Scharte, D; Szymanski, J; Goeser, T; Toex, U; Scheidel, B; Lehmacher, W

2005-03-01

This paper describes four studies investigating the dissolution, plasma pharmacokinetics and safety of a novel, fast-acting ibuprofen formulation, ibuprofen sodium dihydrate. Four separate studies investigated: the in vitro dissolution rates of ibuprofen sodium dihydrate (at pH 1.2, 3.5 and 7.2); the bioavailability of ibuprofen sodium dihydrate (in two pharmacokinetic studies; combined n = 38) compared with conventional ibuprofen, ibuprofen lysinate, ibuprofen arginate and ibuprofen liquagels (all 2 x 200 mg ibuprofen); and the gastroduodenal tolerance of ibuprofen sodium dihydrate and ibuprofen arginate (both 2 x 200 mg ibuprofen t.i.d.) in an endoscopy safety study, where endoscopy was performed at baseline and at the end of each treatment period using a five-point scale to assess the integrity of the gastric and duodenal mucosa. Ibuprofen sodium dihydrate dissolved significantly more rapidly at pH 1.2, 3.5 and 7.2 than conventional ibuprofen, ibuprofen lysinate and ibuprofen liquagels. Ibuprofen sodium dihydrate had similar C(max) to ibuprofen lysinate and ibuprofen liquagels and significantly higher Cmax than conventional ibuprofen (p = 0.002). The mean plasma concentration for ibuprofen sodium dihydrate was significantly higher than for conventional ibuprofen (p = 0.028) 10 minutes post-dose and the t(max) for ibuprofen sodium dihydrate was reached significantly earlier than for conventional ibuprofen (p = 0.018). All three formulations were bioequivalent according to the acceptable boundaries (90% confidence intervals). No statistically significant difference was observed between the ibuprofen formulations in terms of adverse events and specifically with respect to hemorrhagic scores; 41 (46.0%) adverse events (AEs) occurred after administration of ibuprofen sodium dihydrate, and 46 (52.9%) after ibuprofen arginate. One occurrence of an invasive ulcer was observed after administration of ibuprofen arginate. The new formulation of ibuprofen sodium dihydrate dissolves quickly in vitro, has the same extent of absorption as other fast-acting ibuprofen formulations, and is absorbed into plasma more rapidly than conventional ibuprofen. In addition, the present studies suggest that the tolerability and safety profile of ibuprofen sodium dihydrate is comparable to existing ibuprofen formulations.

Factors affecting calcium oxalate dihydrate fragmented calculi regrowth

PubMed Central

Costa-Bauzá, A; Perelló, J; Isern, B; Sanchis, P; Grases, F

2006-01-01

Background The use of extracorporeal shock wave lithotripsy (ESWL) to treat calcium oxalate dihydrate (COD) renal calculi gives excellent fragmentation results. However, the retention of post-ESWL fragments within the kidney remains an important health problem. This study examined the effect of various urinary conditions and crystallization inhibitors on the regrowth of spontaneously-passed post-ESWL COD calculi fragments. Methods Post-ESWL COD calculi fragments were incubated in chambers containing synthetic urine varying in pH and calcium concentration: pH = 5.5 normocalciuria (3.75 mM), pH = 5.5 hypercalciuria (6.25 mM), pH = 6.5 normocalciuria (3.75 mM) or pH = 6.5 hypercalciuria (6.25 mM). Fragment growth was evaluated by measuring increases in weight. Fragment growth was standardized by calculating the relative mass increase. Results Calcium oxalate monohydrate (COM) crystals formed on COD renal calculi fragments under all conditions. Under pH = 5.5 normocalciuria conditions, only COM crystals formed (growth rate = 0.22 ± 0.04 μg/mg·h). Under pH = 5.5 hypercalciuria and under pH = 6.5 normocalciuria conditions, COM crystals and a small number of new COD crystals formed (growth rate = 0.32 ± 0.03 μg/mg·h and 0.35 ± 0.05 μg/mg·h, respectively). Under pH = 6.5 hypercalciuria conditions, large amounts of COD, COM, hydroxyapatite and brushite crystals formed (growth rate = 3.87 ± 0. 34 μg/mg·h). A study of three crystallization inhibitors demonstrated that phytate completely inhibited fragment growth (2.27 μM at pH = 5.5 and 4.55 μM at pH = 6.5, both under hypercalciuria conditions), while 69.0 μM pyrophosphate caused an 87% reduction in mass under pH = 6.5 hypercalciuria conditions. In contrast, 5.29 mM citrate did not inhibit fragment mass increase under pH = 6.5 hypercalciuria conditions. Conclusion The growth rate of COD calculi fragments under pH = 6.5 hypercalciuria conditions was approximately ten times that observed under the other three conditions. This observation suggests COD calculi residual fragments in the kidneys together with hypercalciuria and high urinary pH values may be a risk factor for stone growth. The study also showed the effectiveness of specific crystallization inhibitors in slowing calculi fragment growth. PMID:16822299

Size-dependent cellular uptake mechanism and cytotoxicity toward calcium oxalate on Vero cells

NASA Astrophysics Data System (ADS)

Sun, Xin-Yuan; Gan, Qiong-Zhi; Ouyang, Jian-Ming

2017-02-01

Urinary crystals with various sizes are present in healthy individuals and patients with kidney stone; however, the cellular uptake mechanism of calcium oxalate of various sizes has not been elucidated. This study aims to compare the internalization of nano-/micron-sized (50 nm, 100 nm, and 1 μm) calcium oxalate monohydrate (COM) and dihydrate (COD) crystals in African green monkey renal epithelial (Vero) cells. The internalization and adhesion of COM and COD crystals to Vero cells were enhanced with decreasing crystal size. Cell death rate was positively related to the amount of adhered and internalized crystals and exhibited higher correlation with internalization than that with adhesion. Vero cells mainly internalized nano-sized COM and COD crystals through clathrin-mediated pathways as well as micron-sized crystals through macropinocytosis. The internalized COM and COD crystals were distributed in the lysosomes and destroyed lysosomal integrity to some extent. The results of this study indicated that the size of crystal affected cellular uptake mechanism, and may provide an enlightenment for finding potential inhibitors of crystal uptake, thereby decreasing cell injury and the occurrence of kidney stones.

Kidney Stones in Primary Hyperoxaluria: New Lessons Learnt

PubMed Central

Jacob, Dorrit E.; Grohe, Bernd; Geßner, Michaela; Beck, Bodo B.; Hoppe, Bernd

2013-01-01

To investigate potential differences in stone composition with regard to the type of Primary Hyperoxaluria (PH), and in relation to the patient’s medical therapy (treatment naïve patients versus those on preventive medication) we examined twelve kidney stones from ten PH I and six stones from four PH III patients. Unfortunately, no PH II stones were available for analysis. The study on this set of stones indicates a more diverse composition of PH stones than previously reported and a potential dynamic response of morphology and composition of calculi to treatment with crystallization inhibitors (citrate, magnesium) in PH I. Stones formed by PH I patients under treatment are more compact and consist predominantly of calcium-oxalate monohydrate (COM, whewellite), while calcium-oxalate dihydrate (COD, weddellite) is only rarely present. In contrast, the single stone available from a treatment naïve PH I patient as well as stones from PH III patients prior to and under treatment with alkali citrate contained a wide size range of aggregated COD crystals. No significant effects of the treatment were noted in PH III stones. In disagreement with findings from previous studies, stones from patients with primary hyperoxaluria did not exclusively consist of COM. Progressive replacement of COD by small COM crystals could be caused by prolonged stone growth and residence times in the urinary tract, eventually resulting in complete replacement of calcium-oxalate dihydrate by the monohydrate form. The noted difference to the naïve PH I stone may reflect a reduced growth rate in response to treatment. This pilot study highlights the importance of detailed stone diagnostics and could be of therapeutic relevance in calcium-oxalates urolithiasis, provided that the effects of treatment can be reproduced in subsequent larger studies. PMID:23940605

Metamagnetism and weak ferromagnetism in nickel (II) oxalate crystals

NASA Astrophysics Data System (ADS)

Romero-Tela, E.; Mendoza, M. E.; Escudero, R.

2012-05-01

Microcrystals of orthorhombic nickel (II) oxalate dihydrate were synthesized through a precipitation reaction of aqueous solutions of nickel chloride and oxalic acid. Magnetic susceptibility exhibits a sharp peak at 3.3 K and a broad rounded maximum near 43 K. We associated the lower maximum with a metamagnetic transition that occurs when the magnetic field is about ≥ 3.5 T. The maximum at 43 K is typical of 1D antiferromagnets, whereas weak ferromagnetism behavior was observed in the range of 3.3-43 K.

Structure of Radicals from X-irradiated Guanine Derivatives: An Experimental and Computational Study of Sodium Guanosine Dihydrate Single Crystals

PubMed Central

Jayatilaka, Nayana; Nelson, William H.

2008-01-01

In sodium guanosine dihydrate single crystals, the guanine moiety is deprotonated at N1 due to growth from high-pH (>12) solutions. EPR and ENDOR study of crystals x-irradiated at 10 K detected evidence for three radical forms. Radical R1,characterized by two proton and two nitrogen hyperfine interactions, was identified as the product of net hydrogenation at N7 of the N1-deprotonated guanine unit. R1 exhibited an unusually distorted structure leading to net positive isotropic components of the hydrogen couplings. Radical R2, characterized by one proton and one nitrogen hyperfine coupling was identified as the primary electron loss product. This product is equivalent to that of deprotonation at N1 by the guanine cation and represents the first ENDOR characterization of that product. Radical R3, characterized by a single hydrogen hyperfine coupling, was identified as the product of net dehydrogenation at C1 of the ribose moiety. The identification of radicals R1-R3 was supported by DFT calculations on several possible structures using the B3LYP/6-311G(2df,p)//6-31G(d,p) approach. Radical R4, detected after warming the crystals to room temperature, was identified as the well-known product of net hydrogenation of C8 of the (N1-deprotonated) guanine component. Radical R1, evidently formed by protonation of the primary electron addition product, was present as roughly 60% of the total radicals detected at 10 K. Radical R2 was present as roughly 27% of the total yield, and the concentration of R3 contributed the remaining 13%. R3 is evidently the product of oneelectron oxidation followed by deprotonation; thus, the balance of oxidation and reduction products is approximately equal within experimental uncertainty. PMID:17249824

Ultrasonication as a potential tool to predict solute crystallization in freeze-concentrates.

PubMed

Ragoonanan, Vishard; Suryanarayanan, Raj

2014-06-01

We hypothesize that ultrasonication can accelerate solute crystallization in freeze-concentrates. Our objective is to demonstrate ultrasonication as a potential predictive tool for evaluating physical stability of excipients in frozen solutions. The crystallization tendencies of lyoprotectants (trehalose, sucrose), carboxylic acid buffers (citric, tartaric, malic, and acetic) and an amino acid buffer (histidine HCl) were studied. Aqueous solutions of buffers, lyoprotectants and mixtures of the two were cooled from room temperature to -20°C and sonicated to induce solute crystallization. The crystallized phases were identified by X-ray diffractometry (laboratory or synchrotron source). Sonication accelerated crystallization of trehalose dihydrate in frozen trehalose solutions. Sonication also enhanced solute crystallization in tartaric (200 mM; pH 5), citric (200 mM pH 4) and malic (200 mM; pH 4) acid buffers. At lower buffer concentrations, longer annealing times following sonication were required to facilitate solute crystallization. The time for crystallization of histidine HCl progressively increased as a function of sucrose concentration. The insonation period required to effect crystallization also increased with sucrose concentration. Sonication can substantially accelerate solute crystallization in the freeze-concentrate. Ultrasonication may be useful in assessing the crystallization tendency of formulation constituents used in long term frozen storage and freeze-drying.

PLAN VIEW OF FUEL STORAGE BUILDING (CPP603) SHOWING STORAGE BASINS. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

PLAN VIEW OF FUEL STORAGE BUILDING (CPP-603) SHOWING STORAGE BASINS. INL DRAWING NUMBER 200-0603-00-706-051285. ALTERNATE ID NUMBER CPP-D-1285. - Idaho National Engineering Laboratory, Idaho Chemical Processing Plant, Fuel Reprocessing Complex, Scoville, Butte County, ID

Comparative Study of 14C-Labeled Purified Protein Derivative from Various Mycobacteria

PubMed Central

Landi, S.; Held, H. R.; Tseng, M. C.

1970-01-01

Biologically active 14C-labeled purified protein derivative (14C-PPD) has been prepared from the culture filtrates of seven species of mycobacteria, namely Mycobacterium tuberculosis Johnston strain (PPD), M. bovis BCG (PPD-BCG), M. avium (PPD-A), M. kansasii (PPD-Y), M. intracellulare (PPD-B), M. scrofulaceum (PPD-G), and M. fortuitum (PPD-F). These mycobacteria were grown in a culture medium containing a mixture of 14C-labeled amino acids. The yield and specific radioactivity of the PPD, of the nucleic acid, of the bacterial cells, and of the CO2 developed during growth have been determined for each of the seven species of mycobacteria. Although the yields of 14C-PPD antigens differed greatly for the different species of mycobacteria tested, their specific radioactivities were similar. The 14C-PPD antigens have been used as a means to measure their adsorption to glass. When glass ampoules containing dilute solutions (0.001 mg of PPD per ml) of these PPD antigens (PPD, PPD-BCG, PPD-A, PPD-Y, PPD-G, PPD-B, and PPD-F) were stored for 12 months at 5 C, it was found that they all adsorbed equally well to glass surfaces. In fact, regardless of the origin of the PPD, a loss due to adsorption of about 90% occurred during the first month of storage, and thereafter the PPD content remained practically constant for the rest of the duration of the storage period. The addition of 0.0005% Tween 80 to the PPD solutions effectively reduced the adsorption to glass of most PPD antigens. However, adsorption of PPD-BCG was not quite so effectively prevented, even when the Tween 80 concentration was increased from 0.0005 to 0.0005%. Images PMID:5485082

Fabrication of Carbonate Apatite Block through a Dissolution-Precipitation Reaction Using Calcium Hydrogen Phosphate Dihydrate Block as a Precursor.

PubMed

Tsuru, Kanji; Yoshimoto, Ayami; Kanazawa, Masayuki; Sugiura, Yuki; Nakashima, Yasuharu; Ishikawa, Kunio

2017-03-31

Carbonate apatite (CO₃Ap) block, which is a bone replacement used to repair defects, was fabricated through a dissolution-precipitation reaction using a calcium hydrogen phosphate dihydrate (DCPD) block as a precursor. When the DCPD block was immersed in NaHCO₃ or Na₂CO₃ solution at 80 °C, DCPD converted to CO₃Ap within 3 days. β-Tricalcium phosphate was formed as an intermediate phase, and it was completely converted to CO₃Ap within 2 weeks when the DCPD block was immersed in Na₂CO₃ solution. Although the crystal structures of the DCPD and CO₃Ap blocks were different, the macroscopic structure was maintained during the compositional transformation through the dissolution-precipitation reaction. CO₃Ap block fabricated in NaHCO₃ or Na₂CO₃ solution contained 12.9 and 15.8 wt % carbonate, respectively. The diametral tensile strength of the CO₃Ap block was 2 MPa, and the porosity was approximately 57% regardless of the carbonate solution. DCPD is a useful precursor for the fabrication of CO₃Ap block.

Stimulation of inorganic pyrophosphate elaboration by cultured cartilage and chondrocytes.

PubMed

Ryan, L M; Kurup, I; Rosenthal, A K; McCarty, D J

1989-08-01

Inorganic pyrophosphate elaboration by articular cartilage may favor calcium pyrophosphate dihydrate crystal deposition. Frequently crystal deposits form in persons affected with metabolic diseases. The cartilage organ culture system was used to model these metabolic conditions while measuring the influence on extracellular pyrophosphate elaboration. Alterations of ambient pH, thyroid stimulating hormone levels, and parathyroid hormone levels did not change pyrophosphate accumulation in the media. However, subphysiologic ambient calcium concentrations (25, 100, 500 microM) increased pyrophosphate accumulation about chondrocytes 3- to 10-fold. Low calcium also induced release of [14C]adenine-labeled nucleotides from chondrocytes, potential substrates for generation of extracellular pyrophosphate by ectoenzymes. Exposing cartilage to 10% fetal bovine serum also enhanced by 50% the egress of inorganic pyrophosphate from the tissue.

Structural and vibrational spectroscopic studies on charge transfer and ionic hydrogen bonding interactions of melaminium benzoate dihydrate

NASA Astrophysics Data System (ADS)

Kanagathara, N.; Marchewka, M. K.; Drozd, M.; Gunasekaran, S.; Rajakumar, P. R.; Anbalagan, G.

2015-06-01

Single crystals of melaminium benzoate dihydrate (MBDH) have been grown from aqueous solution by the slow solvent evaporation method at room temperature. Crystalline nature of the grown crystal has been confirmed by X-ray powder diffraction studies. The optimized geometry, frequency and intensity of the vibrational bands of MBDH were obtained by the Hartree-Fock and density functional theory using B3LYP/cam-B3LYP with 6-311++G(d,p) basis set. The harmonic vibrational frequencies were calculated and the scaled values have been compared with the experimental FT-IR and FT-Raman spectral values. The obtained vibrational wavenumbers and optimized geometric parameters are found to be in good agreement with the experimental data. UV-Visible spectrum was recorded in the region 200-400 nm and the electronic properties, HOMO-LUMO energies and other related electronic parameters are calculated. The isotropic chemical shifts computed by 1H and 13C NMR analysis also show good agreement with experimental observation. Natural bond orbital (NBO) analysis has been performed on MBDH compound to analyze the stability of the molecule arising from hyperconjugative interactions and charge delocalization. Molecular electrostatic potential surface (MEP) has also been performed by DFT/cam-B3LYP method with 6-311++G(d,p) basis set. Differential scanning calorimetric measurements performed on the powder sample indicate the phase transition point approximately at 368 and 358 K for heating and cooling, respectively.

Structural and vibrational spectroscopic studies on charge transfer and ionic hydrogen bonding interactions of melaminium benzoate dihydrate.

PubMed

Kanagathara, N; Marchewka, M K; Drozd, M; Gunasekaran, S; Rajakumar, P R; Anbalagan, G

2015-06-15

Single crystals of melaminium benzoate dihydrate (MBDH) have been grown from aqueous solution by the slow solvent evaporation method at room temperature. Crystalline nature of the grown crystal has been confirmed by X-ray powder diffraction studies. The optimized geometry, frequency and intensity of the vibrational bands of MBDH were obtained by the Hartree-Fock and density functional theory using B3LYP/cam-B3LYP with 6-311++G(d,p) basis set. The harmonic vibrational frequencies were calculated and the scaled values have been compared with the experimental FT-IR and FT-Raman spectral values. The obtained vibrational wavenumbers and optimized geometric parameters are found to be in good agreement with the experimental data. UV-Visible spectrum was recorded in the region 200-400 nm and the electronic properties, HOMO-LUMO energies and other related electronic parameters are calculated. The isotropic chemical shifts computed by (1)H and (13)C NMR analysis also show good agreement with experimental observation. Natural bond orbital (NBO) analysis has been performed on MBDH compound to analyze the stability of the molecule arising from hyperconjugative interactions and charge delocalization. Molecular electrostatic potential surface (MEP) has also been performed by DFT/cam-B3LYP method with 6-311++G(d,p) basis set. Differential scanning calorimetric measurements performed on the powder sample indicate the phase transition point approximately at 368 and 358K for heating and cooling, respectively. Copyright © 2015 Elsevier B.V. All rights reserved.

Modulation of polyepoxysuccinic acid on crystallization of calcium oxalate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yanqing; Tang, Yongming, E-mail: tangym@njtech.edu.cn; Xu, Jinqiu

The influence of polyepoxysuccinic acid (PESA) on the phase composition and crystal morphology of calcium oxalate was investigated in this paper. It was found that the presence of PESA inhibited the growth of the monoclinic calcium oxalate monohydrate (COM) crystal and promoted the nucleation of the tetragonal calcium oxalate dihydrate (COD). In addition, with the increase in PESA concentration, the aggregation of COD crystals was reduced but the particle size was increased. Under the conditions of low calcium-to-oxalate ratio and high CaOx concentration, PESA could not effectively stabilize the formation of COD. Based on molecular dynamic simulations, the adsorption ofmore » PESA on CaOx crystal faces was confirmed. - Graphical abstract: Introduction of PESA into crystallization solutions promotes the formation of calcium oxalate dehydrate and modifies the morphology of crystals. - Highlights: • PESA induces the formation of COD at low supersaturation. • Establishment of Ca-rich surface augments the adsorption of PESA. • At Ca/Ox=0.5 PESA cannot induce the formation of COD compared with Ca/Ox=2. • Interaction of PESA with COM faces is stronger than that with COD faces.« less

Evaporative crystallization of salts from Electrodialysis concentrated brine at atmospheric and subatmospheric pressures

NASA Astrophysics Data System (ADS)

Wang, Dong; Du, Wei; Cheng, Penggao; Tang, Na; Wang, Xuekui

2018-02-01

A large amount of concentrated brine was produced as by-product during the process of the electrodialysis seawater desalination. In this study, the crystallization sequences of different salts from the brine through evaporative crystallization at both atmospheric and subatmospheric pressures were investigated in detail. The profile of the boiling temperature with density and the relationship between the boiling temperature and the pressure were recorded. The combination of Powder X-Ray Diffraction and the polarizing microscope was employed to identify the salts in the solid form. It can be inferred that NaCl crystallized out firstly and then MgSO4·6H2O and CaSO4 precipitate in order at both atmospheric and subatmospheric pressures, and it should be noticed that CaSO4 crystallized as anhydrate at 70°C and 90°C while as dihydrate at 50°C. At the end of all the experiments the precipitation rates of CaSO4 and NaCl have reached to more than 95% while MgSO4 only reached to about 60%.

Occurrence and characterisation of calcium oxalate crystals in stems and fruits of Hylocereus costaricensis and Selenicereus megalanthus (Cactaceae: Hylocereeae).

PubMed

Viñas, María; Jiménez, Víctor M

2016-10-01

Detailed description about occurrence of calcium oxalate (CaOx) crystals in the edible vine cactus species Hylocereus costaricensis and Selenicereus megalanthus is scarce. Therefore, we evaluated and characterized the presence, morphology and composition of CaOx crystals in both species. Crystals were isolated from greenhouse and in vitro vegetative stems, and from ripe fruit peels and pulp by enzymatic digestion and density centrifugation and quantified with a haemocytometer. Morphologies were studied using scanning electron microscopy, elemental composition with energy-dispersive X-ray spectroscopy and salt composition with X-ray powder diffraction. Analyses conducted confirmed that isolated crystals were exclusively composed by CaOx, both mono- and dihydrated. Highest crystal contents were measured in greenhouse stems, followed by the fruit peels. While very few crystals were quantified in in vitro plants, they were not detected in the fruit pulp at all, which is of advantage for its human consumption and could be linked to mechanisms of seed dispersal through animals. Different crystal morphologies were observed, sometimes varying between genotypes and tissues analysed. This is the first work known to the authors with a detailed characterization of CaOx crystals in vine cacti. Copyright © 2016 Elsevier Ltd. All rights reserved.

In Situ Investigation of a Self-Accelerated Cocrystal Formation by Grinding Pyrazinamide with Oxalic Acid.

PubMed

Kulla, Hannes; Greiser, Sebastian; Benemann, Sigrid; Rademann, Klaus; Emmerling, Franziska

2016-07-14

A new cocrystal of pyrazinamide with oxalic acid was prepared mechanochemically and characterized by PXRD, Raman spectroscopy, solid-state NMR spectroscopy, DTA-TG, and SEM. Based on powder X-ray diffraction data the structure was solved. The formation pathway of the reaction was studied in situ using combined synchrotron PXRD and Raman spectroscopy. Using oxalic acid dihydrate the initially neat grinding turned into a rapid self-accelerated liquid-assisted grinding process by the release of crystallization water. Under these conditions, the cocrystal was formed directly within two minutes.

Bis(6-meth-oxy-2-{[tris-(hydroxy-meth-yl)-meth-yl]-imino-meth-yl}phenolato)-copper(II) dihydrate.

PubMed

Zhang, Xiutang; Wei, Peihai; Dou, Jianmin; Li, Bin; Hu, Bo

2009-01-08

In the title compound, [Cu(C(12)H(16)NO(5))(2)]·2H(2)O, the Cu(II) ion adopts a trans-CuN(2)O(4) octa-hedral geometry arising from two N,O,O'-tridentate 6-meth-oxy-2-{[tris-(hydroxy-meth-yl)meth-yl]-imino-meth-yl}phenolate ligands. The Jahn-Teller distortion of the copper centre is unusally small. In the crystal structure, O-H⋯O hydrogen bonds, some of which are bifurcated, link the component species.

Electrodeposited non-stoichiometric tungstic acid for electrochromic applications: film growth modes, crystal structure, redox behavior and stability

NASA Astrophysics Data System (ADS)

Pugolovkin, Leonid V.; Cherstiouk, Olga V.; Plyasova, Lyudmila M.; Molina, Irina Yu.; Kardash, Tatyana Yu.; Stonkus, Olga A.; Yatsenko, Dmitriy A.; Kaichev, Vasily V.; Tsirlina, Galina A.

2016-12-01

Bath composition for cathodic electrodeposition of non-stoichiometric hydrated tungstic acid with high electrochromic efficiency is optimized with account for selective electroreduction of certain isopolytungstates. XRD data for thin electrodeposited films and chemically synthesized bulk tungstic acid dihydrate are compared in the context of reversible oxidation and reduction in hydrogen atmosphere, in presence of Pt catalyst. XPS and TEM techniques are attracted to understand the nature of reversible and less reversible transformations of films in the course of their storage and operation.

Dimethyl 4-[3-(4-meth­oxy­phen­yl)-1-phenyl-1H-pyrazol-4-yl]-2,6-dimethyl-1,4-dihydro­pyridine-3,5-dicarboxyl­ate dihydrate

PubMed Central

Fun, Hoong-Kun; Ooi, Chin Wei; Garudachari, B.; Shivananda, Kammasandra Nanjunda; Isloor, Arun M.

2012-01-01

In the title compound, C27H27N3O5·2H2O, the dihydro­pyridine ring adopts a flattened boat conformation. The central pyrazole ring is essentially planar [maximum deviation of 0.003 (1) Å] and makes dihedral angles of 50.42 (6) and 26.44 (6)° with the benzene rings. In the crystal, mol­ecules are linked via N—H⋯O, O—H⋯O, O—H⋯N and C—H⋯O hydrogen bonds into two-dimensional networks parallel to the bc plane. The crystal structure is further consolidated by weak C—H⋯π inter­actions. PMID:22798871

Crystalline coats or hollow crystals as tools for product design in pharmaceutical industry

NASA Astrophysics Data System (ADS)

Ulrich, J.; Schuster, A.; Stelzer, T.

2013-01-01

The coating of pharmaceutical compounds is a field of high interest. As most of the coating materials form an amorphous layer around the material, the studies on crystalline coatings are rare. In this work the progress in this domain should be summarized and innovative results concerning crystalline hollow needles as coating material are presented. Since the first reports on needles formed via a solvent-mediated phase transition from solvates to hydrates, the field could be widened to hydrate-to-anhydrate and anhydrate-to-hydrate transformations. Novel investigations on hollow theophylline monohydrate and carbamazepine dihydrate needles are presented. It is shown that the inclusion of substances into the hollow needle crystals is feasible by simple means, which enable an application in industry as coating for sensitive materials.

Investigation of recrystallization of amorphous trehalose through hot-humidity stage X-ray powder diffraction.

PubMed

Jójárt-Laczkovich, Orsolya; Katona, Gábor; Aigner, Zoltán; Szabó-Révész, Piroska

2016-12-01

The aim of this work was an investigation of the physical changes of the amorphous model material spray-dried trehalose through the use of various analytical techniques and to identify a suitable, rapid method able to quantify the changes. The crystallinity changes and recrystallization process of amorphous samples were investigated by hot-humidity stage X-ray powder diffractometry (HH-XRPD) with fresh samples, conventional X-ray powder diffractometry (XRPD) used stored samples and by differential scanning calorimetry (DSC). The data from the three methods were compared and the various forms of trehalose were analysed. HH-XRPD demonstrated that the recrystallization began at 40 and 60°C up to 45% RH and at 70°C up to 30% RH into dihydrate form. At 70°C up to 60% RH the anhydrous form of trehalose appeared too. Conventional XRPD results showed, that in the 28days stored samples the dihydrate form was detected at 40°C, 50% RH. Storage at 60°C, 40% RH resulted in the appearance of the anhydrous form and at 60°C, 50% RH both polymorphic forms were detected. By carrying out the DSC measurements at different temperatures the fraction of recrystallized trehalose dihydrate was detected. The recrystallization investigated by HH-XRPD and DSC followed Avrami kinetics, the calculated rate constants of isothermal crystallization (K) were same. Both HH-XRPD and conventional XRPD was suitable for the detection of the physical changes of the amorphous model material. DSC measurements showed similar results as HH-XRPD. Primarily HH-XRPD could be suggested for prediction, because the method is fast and every changes could be studied on one sample. Copyright © 2016 Elsevier B.V. All rights reserved.

Mental Imagery Abilities in Adolescents with Spastic Diplegic Cerebral Palsy

ERIC Educational Resources Information Center

Courbois, Yanick; Coello, Yann; Bouchart, Isabelle

2004-01-01

Four visual imagery tasks were presented to three groups of adolescents with or without spastic diplegic cerebral palsy. The first group was composed of six adolescents with cerebral palsy who had associated visual-perceptual deficits (CP-PD), the second group was composed of five adolescents with cerebral palsy and no associated visual-perceptual…

Pseudogout of the cervical and thoracic spine mimicking infection after lumbar fusion: case report.

PubMed

Bridges, Kelly J; Bullis, Carli L; Wanchu, Ajay; Than, Khoi D

2017-08-01

Pseudogout is a form of acute calcium pyrophosphate deposition (CPPD) disease that typically afflicts the elderly. CPPD commonly involves larger joints, such as the knees, wrists, shoulders, and hips, and has been known to involve the spine. The authors report the case of a 66-year-old woman with a recent history of lumbar laminectomy and fusion who presented 5 weeks postprocedure with a clinical and radiographic picture consistent with multilevel skip lesions involving the cervical and thoracic spine, thoracic discitis, and epidural abscess. Serial blood cultures and repeat biopsy samples were sterile. Subsequent wrist and ankle erythema, pain, and swelling led to synovial fluid analysis, and pseudogout was diagnosed. She was treated with an interleukin-1 inhibitor with immediate symptom relief. To the authors' knowledge, this is only the second report of spinal pseudogout presenting with a clinical and radiographic picture consistent with discitis and epidural abscess. This report is the first to report skip lesions of pseudogout occurring throughout the spine that are uniquely remote from a recent lumbar surgery.

Insights into Hydrate Formation and Stability of Morphinanes from a Combination of Experimental and Computational Approaches

PubMed Central

2014-01-01

Morphine, codeine, and ethylmorphine are important drug compounds whose free bases and hydrochloride salts form stable hydrates. These compounds were used to systematically investigate the influence of the type of functional groups, the role of water molecules, and the Cl– counterion on molecular aggregation and solid state properties. Five new crystal structures have been determined. Additionally, structure models for anhydrous ethylmorphine and morphine hydrochloride dihydrate, two phases existing only in a very limited humidity range, are proposed on the basis of computational dehydration modeling. These match the experimental powder X-ray diffraction patterns and the structural information derived from infrared spectroscopy. All 12 structurally characterized morphinane forms (including structures from the Cambridge Structural Database) crystallize in the orthorhombic space group P212121. Hydrate formation results in higher dimensional hydrogen bond networks. The salt structures of the different compounds exhibit only little structural variation. Anhydrous polymorphs were detected for all compounds except ethylmorphine (one anhydrate) and its hydrochloride salt (no anhydrate). Morphine HCl forms a trihydrate and dihydrate. Differential scanning and isothermal calorimetry were employed to estimate the heat of the hydrate ↔ anhydrate phase transformations, indicating an enthalpic stabilization of the respective hydrate of 5.7 to 25.6 kJ mol–1 relative to the most stable anhydrate. These results are in qualitative agreement with static 0 K lattice energy calculations for all systems except morphine hydrochloride, showing the need for further improvements in quantitative thermodynamic prediction of hydrates having water···water interactions. Thus, the combination of a variety of experimental techniques, covering temperature- and moisture-dependent stability, and computational modeling allowed us to generate sufficient kinetic, thermodynamic and structural information to understand the principles of hydrate formation of the model compounds. This approach also led to the detection of several new crystal forms of the investigated morphinanes. PMID:25036525

Comparative spectroscopic analysis of urinary calculi inhibition by Larrea Tridentata infusion and NDGA chemical extract

NASA Astrophysics Data System (ADS)

Manciu, Felicia

2012-10-01

In the present comparative spectroscopic study we try to understand calcium oxalate kidney stone formation as well as its inhibition by using a traditional medicine approach with Larrea Tridentata (LT) herbal extracts and nordihydroguaiaretic acid (NDGA), which is a chemical extract of the LT bush. The samples were synthesized without and with LT or NDGA using a simplified single diffusion gel growth technique. While the use of infusion from LT decreases the sizes of calcium oxalate crystals and also changes their structure from monohydrate for pure crystals to dihydrate for crystals grown with different amounts of inhibitor, both Raman and infrared absorption spectroscopic techniques, which are the methods of analysis employed in this work, reveal that NDGA is not responsible for the change in the morphology of calcium oxalate crystals and does not contribute significantly to the inhibition process. The presence of NDGA slightly affects the structure of the crystals by modifying the strength of the C-C bonds as seen in the Raman data. Also, the current infrared absorption results demonstrate the presence of NDGA in the samples through a vibrational line that corresponds to the double bond between carbon atoms of the ester group of NDGA.

Effect of aging heat time and annealing temperature on the properties of nanocrystalline tin dioxide thin films

NASA Astrophysics Data System (ADS)

Kadhim, Imad H.; Abu Hassan, H.

2017-04-01

Nanocrystalline tin dioxide (SnO2) thin films have been successfully prepared by sol-gel spin-coating technique on p-type Si (100) substrates. A stable solution was prepared by mixing tin(II) chloride dihydrate, pure ethanol, and glycerin. Temperature affects the properties of SnO2 thin films, particularly the crystallite size where the crystallization of SnO2 with tetragonal rutile structure is achieved when thin films that prepared under different aging heat times are annealed at 400∘C. By increasing aging heat time in the presence of annealing temperatures the FESEM images indicated that the thickness of the fabricated film was directly proportional to solution viscosity, increasing from approximately 380 nm to 744 nm, as well as the crystallization of the thin films improved and reduced defects.

Co-crystallization of cholesterol and calcium phosphate as related to atherosclerosis

NASA Astrophysics Data System (ADS)

Hirsch, Danielle; Azoury, Reuven; Sarig, Sara

1990-09-01

Calcification of atherosclerotic plaques occurs very frequently and aggravates the disease. In biological systems, epitaxial relationships between crystal structures may be important in nucleating the deposit of a solid phase. The biologically preferred calcium phosphate species, apatite, and cholesterol crystal have structurally compatible crystallographic faces which allow epitaxial growth of one crystal upon another. The present study describes a new approach to explore, in vitro, the crystallization processes of calcium phosphate (CaP) with cholesterol (CS) and cholestanol (CN) which are related to atherosclerosis. Aqueous solutions containing calcium and phosphate ions or CaP crystals as hydroxyapatite were added into saturated ethanolic solutions of CS or CS and 10% CN. After precipitation, crystals were collected and analyzed by nuclear magnetic resonance (NMR), infra-red (IR), X-ray, scanning electron microscope (SEM-LINK), differential scanning calorimeter (DSC) and atomic absorption. The principal result is the well-formed crystals precipitation when an aqueous solution and CaP seed crystals were added to saturated solutions of CS and 10% CN. Cholesterol-cholestanol dihydrate (CC2W) crystals precipitated in the presence of CaP seeds were compared to the CC2W crystals obtained without the mineral compound. The results of this comparison indicate a special link between crystals of CaP and CC2W, and support the epitaxial relationship between the two kinds of crystals. The potential of CC2W crystals to be precipitated by CaP seed crystals prove likewise the possible significant role of the cholestanol metabolite in the process of cholesterol crystallization and calcification in the arteries.

Crystallization of calcium oxalate in minimally diluted urine

NASA Astrophysics Data System (ADS)

Bretherton, T.; Rodgers, A.

1998-09-01

Crystallization of calcium oxalate was studied in minimally diluted (92%) urine using a mixed suspension mixed product crystallizer in series with a Malvern particle sizer. The crystallization was initiated by constant flow of aqueous sodium oxalate and urine into the reaction vessel via two independent feed lines. Because the Malvern cell was in series with the reaction vessel, noninvasive measurement of particle sizes could be effected. In addition, aliquots of the mixed suspension were withdrawn and transferred to a Coulter counter for crystal counting and sizing. Steady-state particle size distributions were used to determine nucleation and growth kinetics while scanning electron microscopy was used to examine deposited crystals. Two sets of experiments were performed. In the first, the effect of the concentration of the exogenous sodium oxalate was investigated while in the second, the effect of temperature was studied. Calcium oxalate nucleation and growth rates were found to be dependent on supersaturation levels inside the crystallizer. However, while growth rate increased with increasing temperature, nucleation rates decreased. The favored phases were the trihydrate at 18°C, the dihydrate at 38° and the monohydrate at 58°C. The results of both experiments are in agreement with those obtained in other studies that have been conducted in synthetic and in maximally diluted urine and which have employed invasive crystal counting and sizing techniques. As such, the present study lends confidence to the models of urinary calcium oxalate crystallization processes which currently prevail in the literature.

Acute neck pain caused by pseudogout attack of calcified cervical yellow ligament: a case report.

PubMed

Kobayashi, Takashi; Miyakoshi, Naohisa; Abe, Toshiki; Abe, Eiji; Kikuchi, Kazuma; Noguchi, Hideaki; Konno, Norikazu; Shimada, Yoichi

2016-05-30

Calcification of the yellow ligament sometimes compresses the spinal cord and can induce myelopathy. Usually, the calcification does not induce acute neck pain. We report a case of a patient with acute neck pain caused by calcium pyrophosphate dihydrate in a calcified cervical yellow ligament. A 70-year-old Japanese woman presented with acute neck pain. She had a moderately high fever (37.5 °C), and her neck pain was so severe that she could not move her neck in any direction. Computed tomography showed a high-density area between the C5 and C6 laminae suspicious for calcification of the yellow ligament. Magnetic resonance imaging showed intermediate-signal intensity on T1-weighted imaging and high-signal intensity on T2-weighted imaging surrounding a low-signal region on both T1- and T2-weighted imaging with cord compression. There was a turbid, yellow fluid collection in the yellow ligament at the time of operation. Histologically, calcium pyrophosphate dihydrate crystals were found in the fluid, and she was diagnosed as having a pseudogout attack of the yellow ligament. Pseudogout attack of the cervical yellow ligament is rare, but this clinical entity should be added to the differential diagnosis of acute neck pain, especially when calcification of the yellow ligament exists.

Calcium-deficient apatite synthesized by ammonia hydrolysis of dicalcium phosphate dihydrate: influence of temperature, time, and pressure.

PubMed

Obadia, Laetitia; Rouillon, Thierry; Bujoli, Bruno; Daculsi, Guy; Bouler, Jean Michel

2007-01-01

In this work, calcium-deficient apatites (CDA) were synthesized by ammonia hydrolysis reaction of dicalcium phosphate dihydrate (DCPD; CaHPO4 x 2 H2O) to obtain biphasic calcium phosphates (BCP) without any extraionic substitution. The influence of three parameters was studied: temperature of the reaction (70 and 100 degrees C), time of the reaction (4 and 18 h), and the pressure (open and closed system). Experiments were made according to a factorial design method (FDM) allowing optimization of the number of samples as well as statistical analysis of results. Moreover, the influence of temperature (until 200 degrees C) was investigated. The crystal size of CDA was determined according to the Scherrer's formula and from Rietveld refinements taking the CDA anisotropy into account. The last method seems to be a reliable method to determine crystallite sizes of CDA, since crystallite sizes of CDA along <00l> and directions were accessible. The results describe the hydroxyapatite % (HA%) in BCP by a first-order polynomial equation in the experimental area studied and the HA content was found to increase by raising time and temperature of the reaction. Moreover, the type of reaction system (open/closed vessel) appeared to have little influence on HA%. 2006 Wiley Periodicals, Inc.

Temperature-dependent formation of NaCl dihydrate in levitated NaCl and sea salt aerosol particles.

PubMed

Peckhaus, Andreas; Kiselev, Alexei; Wagner, Robert; Duft, Denis; Leisner, Thomas

2016-12-28

Recent laboratory studies indicate that the hydrated form of crystalline NaCl is potentially important for atmospheric processes involving depositional ice nucleation on NaCl dihydrate particles under cirrus cloud conditions. However, recent experimental studies reported a strong discrepancy between the temperature intervals where the efflorescence of NaCl dihydrate has been observed. Here we report the measurements of the volume specific nucleation rate of crystalline NaCl in the aqueous solution droplets of pure NaCl suspended in an electrodynamic balance at constant temperature and humidity in the range from 250 K to 241 K. Based on these measurements, we derive the interfacial energy of crystalline NaCl dihydrate in a supersaturated NaCl solution and determined its temperature dependence. Taking into account both temperature and concentration dependence of nucleation rate coefficients, we explain the difference in the observed fractions of NaCl dihydrate reported in the previous studies. Applying the heterogeneous classical nucleation theory model, we have been able to reproduce the 5 K shift of the NaCl dihydrate efflorescence curve observed for the sea salt aerosol particles, assuming the presence of super-micron solid inclusions (hypothetically gypsum or hemihydrate of CaSO 4 ). These results support the notion that the phase transitions in microscopic droplets of supersaturated solution should be interpreted by accounting for the stochastic nature of homogeneous and heterogeneous nucleation and cannot be understood on the ground of bulk phase diagrams alone.

Temperature-dependent formation of NaCl dihydrate in levitated NaCl and sea salt aerosol particles

NASA Astrophysics Data System (ADS)

Peckhaus, Andreas; Kiselev, Alexei; Wagner, Robert; Duft, Denis; Leisner, Thomas

2016-12-01

Recent laboratory studies indicate that the hydrated form of crystalline NaCl is potentially important for atmospheric processes involving depositional ice nucleation on NaCl dihydrate particles under cirrus cloud conditions. However, recent experimental studies reported a strong discrepancy between the temperature intervals where the efflorescence of NaCl dihydrate has been observed. Here we report the measurements of the volume specific nucleation rate of crystalline NaCl in the aqueous solution droplets of pure NaCl suspended in an electrodynamic balance at constant temperature and humidity in the range from 250 K to 241 K. Based on these measurements, we derive the interfacial energy of crystalline NaCl dihydrate in a supersaturated NaCl solution and determined its temperature dependence. Taking into account both temperature and concentration dependence of nucleation rate coefficients, we explain the difference in the observed fractions of NaCl dihydrate reported in the previous studies. Applying the heterogeneous classical nucleation theory model, we have been able to reproduce the 5 K shift of the NaCl dihydrate efflorescence curve observed for the sea salt aerosol particles, assuming the presence of super-micron solid inclusions (hypothetically gypsum or hemihydrate of CaSO4). These results support the notion that the phase transitions in microscopic droplets of supersaturated solution should be interpreted by accounting for the stochastic nature of homogeneous and heterogeneous nucleation and cannot be understood on the ground of bulk phase diagrams alone.

Bis[2-(2-pyridylmethyl­eneamino)benzene­sulfonato-κ3 N,N′,O]cobalt(II) dihydrate

PubMed Central

Huang, Xue-Ren; Ou-Yang, Miao; Yang, Ge-Ge; Meng, Xiu-Jin; Jiang, Yi-Min

2009-01-01

The title complex, [Co(C12H9N2O3S)2]·2H2O, has site symmetry 2 with the CoII cation located on a twofold rotation axis. Two tridentate 2-(2-pyridylmethyl­eneamino)benzene­sulfonate (paba) ligands chelate to the CoII cation in a distorted octa­hedral geometry. The pyridine and benzene rings in the paba ligand are oriented at a dihedral angle of 42.86 (13)°. Inter­molecular O—H⋯O and C—H⋯O hydrogen bonding is present in the crystal structure. PMID:21578190

Herbal extracts of Tribulus terrestris and Bergenia ligulata inhibit growth of calcium oxalate monohydrate crystals in vitro

NASA Astrophysics Data System (ADS)

Joshi, V. S.; Parekh, B. B.; Joshi, M. J.; Vaidya, A. B.

2005-02-01

A large number of people in this world are suffering from urinary stone problem. Calcium oxalate monohydrate (COM) and calcium oxalate dihydrate (COD) containing stones (calculi) are commonly found. In the present study, COM crystals were grown by a double diffusion gel growth technique using U-tubes. The gel was prepared from hydrated sodium metasilicate solution. The gel framework acts like a three-dimensional crucible in which the crystal nuclei are delicately held in the position of their formation, and nutrients are supplied for the growth. This technique can be utilized as a simplified screening static model to study the growth, inhibition and dissolution of urinary stones in vitro. The action of putative litholytic medicinal plants, Tribulus terrestris Linn. ( T.t) and Bergenia ligulata Linn. ( B.l.), has been studied in the growth of COM crystals. Tribulus terrestris and Bergenia ligulata are commonly used as herbal medicines for urinary calculi in India. To verify the inhibitive effect, aqueous extracts of Tribulus terrestris and Bergenia ligulata were added along with the supernatant solutions. The growth was measured and compared, with and without the aqueous extracts. Inhibition of COM crystal growth was observed in the herbal extracts. Maximum inhibition was observed in Bergenia ligulata followed by Tribulus terrestris. The results are discussed.

Effect of NH4-N/P and Ca/P molar ratios on the reactive crystallization of calcium phosphates for phosphorus recovery from wastewater

NASA Astrophysics Data System (ADS)

Vasenko, Liubov; Qu, Haiyan

2017-02-01

In this work, the effects of operational parameters, initial phosphorus concentration and molar ratios of Ca/P and NH4-N/P (further in the text N/P), on the nature and purity of precipitated phosphorus products have been investigated in an artificial system that mimics the supernatant in wastewater treatment plants. Metastable zone width was determined for two target phosphorus products: DCPD (dicalcium phosphate dihydrate) and HAp (hydroxyapatite) in the range of pH 4.5 - 7. HAp crystallizes at final pH higher than 6.3 while DCPD crystallizes at the final pH in between 4.7 and 5.7. At the final pH 5.7 - 6.3 and at pH lower than 4.7 the mixtures of DCPD and HAp were obtained. It was observed that N/P ratio affects not only the metastable zone width but also the kinetics of crystal growth for both DCPD and HAp: the higher the N/P ratio, the lower is the growth rate for both P-products. Investigation of the effect of Ca/P and N/P ratios on the nucleation and crystal growth of DCPD in batch crystallization experiment was performed. It showed that at high supersaturation level, crystals with larger median size can be obtained at higher N/P ratio despite the negative effects of N/P ratio on the growth rate of the crystals.

Flow of ices in the Ammonia-Water System

NASA Technical Reports Server (NTRS)

Durham, W. B.; Kirby, S. H.; Stern, L. A.

1993-01-01

We have fabricated in the laboratory and subsequently deformed crystalline hydrates and partial melts of the water-rich end of the NH3-H2O system, with the aim of improving our understanding of physical processes occurring in icy moons of the outer solar system. Deformation experiments were carried out at constant strain rate. The range of experimental variables are given. Phase relationships in the NH3-H2O system indicate that water ice and ammonia dihydrate, NH3-2H2O, are the stable phases under our experiment conditions. X-ray diffraction of our samples usually revealed these as the dominant phases, but we have also observed an amorphous phase (in unpressurized samples only) and occasionally significant ammonia monohydrate, NH3-H2O. The onset of partial melting at the peritectic temperature at about 176 K appeared as a sharp transition in strength observed in samples of x(sub NH3) = 0.05 and 0.01, the effect of melt was less pronounced. For any given water ice + dihydrate alloy in the subsolidus region, we observed one rheological law over the entire temperature range from 175 K to about 140 K. Below 140 K, a shear instability similar to that occurring in pure water ice under the same conditions limited our ability to measure ductile flow. The rheological laws for the several alloys vary systematically from that of pure ice to that of dihydrate. Pure dihydrate is about 4 orders of magnitude less viscous than water ice just below the peritectic temperature, but because of a very pronounced temperature dependence in dihydrate (100 kJ/mol versus 43 kJ/mol for water ice) the viscosity of dihydrate equals or exceeds that of water ice at T less than 140 K. The large variation in viscosity of dihydrate with relatively small changes in temperature may be helpful in explaining the rich variety of tectonic and volcanic features seen on the surfaces of icy moons in the outer solar system.

Revisiting polarimetry near the isotropic point of an optically active, non-enantiomorphous, molecular crystal.

PubMed

Martin, Alexander T; Tan, Melissa; Nichols, Shane M; Timothy, Emily; Kahr, Bart

2018-07-01

Accurate polarimetric measurements of the optical activity of crystals along low symmetry directions are facilitated by isotropic points, frequencies where dispersion curves of eigenrays cross and the linear birefringence disappears. We report here the optical properties and structure of achiral, uniaxial (point group D 2d ) potassium trihydrogen di-(cis-4-cyclohexene-1,2-dicarboxylate) dihydrate, whose isotropic point was previously detected (S. A. Kim, C. Grieswatch, H. Küppers, Zeit. Krist. 1993; 208:219-222) and exploited for a singular measurement of optical activity normal to the optic axis. The crystal structure associated with the aforementioned study was never published. We report it here, confirming the space group assignment I 4¯c2, along with the frequency dependence of the fundamental optical properties and the constitutive tensors by fitting optical dispersion relations to measured Mueller matrix spectra. k-Space maps of circular birefringence and of the Mueller matrix near the isotropic wavelength are measured and simulated. The signs of optical rotation are correlated with the absolute crystallographic directions. © 2018 Wiley Periodicals, Inc.

Higher plasma quercetin levels following oral administration of an onion skin extract compared with pure quercetin dihydrate in humans.

PubMed

Burak, Constanze; Brüll, Verena; Langguth, Peter; Zimmermann, Benno F; Stoffel-Wagner, Birgit; Sausen, Udo; Stehle, Peter; Wolffram, Siegfried; Egert, Sarah

2017-02-01

To investigate the plasma kinetics of quercetin derived from hard capsules filled with onion skin extract powder or quercetin dihydrate in humans. In a randomized, single-blind, diet-controlled crossover study, 12 healthy subjects (six men and six women) aged 21-33 years were administered a single oral supra-nutritional dose of approximately 163 mg quercetin derived from onion skin extract powder (containing 95.3 % of total flavonoids as quercetin aglycone) or quercetin dihydrate (134 mg quercetin aglycone equivalent). Blood samples were collected before and during a 24-h period after quercetin administration. The concentrations of quercetin and its two monomethylated derivatives, isorhamnetin (3'-O-methyl quercetin), and tamarixetin (4'-O-methyl quercetin), were measured using HPLC with fluorescence detection after plasma enzymatic treatment. The systemic availability, determined by comparing the plasma concentration-time curves of quercetin, was 4.8 times higher, and the maximum plasma concentration (C max ) was 5.4 times higher after ingestion of the onion skin extract than after ingestion of pure quercetin dihydrate. By contrast, t max did not differ significantly between the two formulations. The C max values for isorhamnetin and tamarixetin were 3.8 and 4.4 times higher, respectively, after administration of onion skin extract than after pure quercetin dihydrate. The plasma kinetics of quercetin were not significantly different in men and women. Quercetin aglycone derived from onion skin extract powder is significantly more bioavailable than that from quercetin dihydrate powder filled hard capsules.

Effects of Oxalic Acid on Apis mellifera (Hymenoptera: Apidae)

PubMed Central

Rademacher, Eva; Harz, Marika; Schneider, Saskia

2017-01-01

Oxalic acid dihydrate is used to treat varroosis of Apis mellifera. This study investigates lethal and sublethal effects of oxalic acid dihydrate on individually treated honeybees kept in cages under laboratory conditions as well as the distribution in the colony. After oral application, bee mortality occurred at relatively low concentrations (No Observed Adverse Effect Level (NOAEL) 50 µg/bee; Lowest Observed Adverse Effect Level (LOAEL) 75 µg/bee) compared to the dermal treatment (NOAEL 212.5 µg/bee; LOAEL 250 µg/bee). The dosage used in regular treatment via dermal application (circa 175 µg/bee) is below the LOAEL, referring to mortality derived in the laboratory. However, the treatment with oxalic acid dihydrate caused sublethal effects: This could be demonstrated in an increased responsiveness to water, decreased longevity and a reduction in pH-values in the digestive system and the hemolymph. The shift towards stronger acidity after treatment confirms that damage to the epithelial tissue and organs is likely to be caused by hyperacidity. The distribution of oxalic acid dihydrate within a colony was shown by macro-computed tomography; it was rapid and consistent. The increased density of the individual bee was continuous for at least 14 days after the treatment indicating the presence of oxalic acid dihydrate in the hive even long after a treatment. PMID:28783129

The Strategic Leadership of Admiral Chester W. Nimitz

DTIC Science & Technology

2012-03-19

leadership frameworks can prove useful in this analysis including the U.S. Navy’s Center for Personal and Professional Development’s (CPPD) 3 Navy...severe case of dermatitis and needed hospital care. With a Japanese carrier and invasion force bearing down on Midway, Admiral Nimitz had lost his...includes other key competencies not specifically spelled out in the NLCM including an emphasis on self-awareness, professional development and the

Novel selective kappa-opioid ligands.

PubMed

Peeters, O M; Jamroz, D; Blaton, N M; De Ranter, C J

1999-03-15

The single-crystal X-ray structures of (-)-dimethyl[(2S)-1-(5,6,7,8- tetrahydro-5-oxonaphthalene-2-acetyl)piperidin-2-ylmethyl ]ammonium chloride, C20H29N2O2+.Cl-(BRL-53001A), and (-)-ethylmethyl[(2S)-1-(5,6,7,8-tetrahydro-5-oxonaphthalene- 2- acetyl)piperidin-2-ylmethyl]-ammonium chloride dihydrate, C21H31N2O2+.Cl-.2H2O (BRL-53188A), have been determined. The two molecules have different conformations in the 1-tetralon-6-ylacetyl residue but the same conformation in the 1-acetyl-2-(dialkylaminomethyl)piperidine moiety. The conformations found are in agreement with the required chemical features for kappa affinity and antinociceptive potency.

Molecular structure and vibrational spectra of Bis(melaminium) terephthalate dihydrate: A DFT computational study

NASA Astrophysics Data System (ADS)

Tanak, Hasan; Marchewka, Mariusz K.; Drozd, Marek

2013-03-01

The experimental and theoretical vibrational spectra of Bis(melaminium) terephthalate dihydrate were studied. The Fourier transform infrared (FT-IR) spectra of the Bis(melaminium) terephthalate dihydrate and its deuterated analogue were recorded in the solid phase. The molecular geometry and vibrational frequencies of Bis(melaminium) terephthalate dihydrate in the ground state have been calculated by using the density functional method (B3LYP) with 6-31++G(d,p) basis set. The results of the optimized molecular structure are presented and compared with the experimental X-ray diffraction. The molecule contains the weak hydrogen bonds of Nsbnd H⋯O, Nsbnd H⋯N and Osbnd H⋯O types, and those bonds are calculated with DFT method. In addition, molecular electrostatic potential, frontier molecular orbitals and natural bond orbital analysis of the title compound were investigated by theoretical calculations. The lack of the second harmonic generation (SHG) confirms the presence of macroscopic center of inversion.

Molecular structure and vibrational spectra of Bis(melaminium) terephthalate dihydrate: a DFT computational study.

PubMed

Tanak, Hasan; Marchewka, Mariusz K; Drozd, Marek

2013-03-15

The experimental and theoretical vibrational spectra of Bis(melaminium) terephthalate dihydrate were studied. The Fourier transform infrared (FT-IR) spectra of the Bis(melaminium) terephthalate dihydrate and its deuterated analogue were recorded in the solid phase. The molecular geometry and vibrational frequencies of Bis(melaminium) terephthalate dihydrate in the ground state have been calculated by using the density functional method (B3LYP) with 6-31++G(d,p) basis set. The results of the optimized molecular structure are presented and compared with the experimental X-ray diffraction. The molecule contains the weak hydrogen bonds of N-H···O, N-H···N and O-H···O types, and those bonds are calculated with DFT method. In addition, molecular electrostatic potential, frontier molecular orbitals and natural bond orbital analysis of the title compound were investigated by theoretical calculations. The lack of the second harmonic generation (SHG) confirms the presence of macroscopic center of inversion. Copyright © 2012 Elsevier B.V. All rights reserved.

Effects of Temperature and Humidity History on Brittleness of α-Sulfonated Fatty Acid Methyl Ester Salt Crystals.

PubMed

Watanabe, Hideaki; Morigaki, Atsunori; Kaneko, Yukihiro; Tobori, Norio; Aramaki, Kenji

2016-01-01

α-Sulfonated fatty acid methyl ester salts (MES), which were made from vegetable sources, are attractive candidates for eco-friendly washing detergents because they have various special features like excellent detergency, favorable biodegradability, and high stability against enzymes. To overcome some disadvantages of powder-type detergents like caking, sorting, and dusting, we studied how temperature and humidity history, as a model for long-term storage conditions, can affect crystalline structures and reduce the brittleness of MES powder. We characterized the crystalline structure of MES grains using small-angle X-ray scattering, wide-angle X-ray scattering, differential scanning calorimetry, and Fourier transform infrared spectroscopy measurements and determined the yield values, which measure the brittleness of MES grains, in shear stress using dynamic viscoelasticity measurements. This study confirmed that MES crystals form three pseudo-polymorphs via thermal or humidity conditioning: metastable crystals (αsubcell), anhydrous crystals (β subcell), and dihydrate crystals (β' subcell). Further, we found that the yield value increases upon phase transition from the β subcell to the β' subcell and from the β' subcell to the αsubcell. Therefore, controlling the thermal and humidity conditioning of MES grains is an effective way to decrease the brittleness of MES powders and can be used to overcome the above mentioned disadvantages of powder-type detergents in the absence of co-surfactants.

Role of Polymeric Excipients in the Stabilization of Olanzapine when Exposed to Aqueous Environments.

PubMed

Paisana, Maria; Wahl, Martin; Pinto, João

2015-12-12

Hydrate formation is a phase transition which can occur during manufacturing processes involving water. This work considers the prevention of hydration of anhydrous olanzapine and hydrate conversions in the presence of water and polymers (polyethyleneglycol; hydroxypropylcellulose; polyvinylpyrrolidone) in forming pellets by wet extrusion and spheronisation. Anhydrous olanzapine was added to water with or without those polymers prior to extrusion with microcrystalline cellulose. Assessment of olanzapine conversion was made by XRP-Diffraction; FTIR spectroscopy; calorimetry (DSC) and microscopy (SEM for crystal size and shape). The addition of water converted the anhydrous form into dihydrate B and higher hydrate; whereas polyethyleneglycol promoted a selective hydrate conversion into the higher hydrate olanzapine form. Both polyvinylpyrrolidone and hydroxypropylcellulose prevented the hydrate transformations of the anhydrous drug; the latter even in the presence of hydrate seeds. This may be explained by the higher H-bond ability; higher network association and higher hydrophobicity of hydroxypropylcellulose by comparison with polyethyleneglycol and polyvinylpyrrolidone; which could contribute to its higher affinity to the crystal surfaces of the hydrate nuclei/initial crystals and promoting steric hindrance to the incorporation of other drug molecules into the crystal lattice; thus, preventing the crystal growth. The addition of microcrystalline cellulose needed for the pellets production (final product) did not eliminate the protector effect of both hydroxypropylcellulose and polyvinylpyrrolidone during pellets' processing and dissolution evaluation.

Budesonide + formoterol fumarate dihydrate for the treatment of asthma.

PubMed

Wolthers, Ole D

2016-01-01

One of the most widely used fixed combinations in asthma management is dry powder budesonide+formoterol fumarate dihydrate which is commercially available as Symbicort Turbuhaler(®) (and generic products), Easyhaler Bufomix(®) and DuoRespSpiromax(®) inhaler. The aim of this paper was to review the fixed dry powder combination of inhaled budesonide+formoterol fumarate dihydrate for asthma treatment in adolescents and adults. A literature search using relevant search terms, reference lists for reviews and meta-analyses was performed. In symptomatic adolescent and adult patients with asthma maintenance and reliever therapy with a single-inhaler fixed combination of dry powder budesonide+formoterol fumarate dihydrate is an evidenced option. The combination treatment is convenient to patients. It reduces the number of exacerbations requiring treatment with oral corticosteroids. In some patients the strategy may also reduce the total intake of inhaled corticosteroids over time. Whether important outcome measures of asthma treatment, such as hospital admission and emergency room visit rates, may be reduced is less well documented since the published studies may have been influenced by publication bias. Non-pharmaceutical company-sponsored research evaluating such measures is needed. There is no evidence for the use of single inhaler fixed combinations of inhaled corticosteroids+long-acting β(2)-agonists in children (<12 years of age), and budesonide+formoterol fumarate dihydrate should not be prescribed to the age group.

Spectroscopic and structural studies of the first complex formed between salinomycin and organic amine

NASA Astrophysics Data System (ADS)

Antoszczak, Michał; Janczak, Jan; Brzezinski, Bogumił; Huczyński, Adam

2017-02-01

For the first time, the crystalline complex of salinomycin with benzylamine was obtained and its molecular structure was studied using single crystal X-ray diffraction, FT-IR, 1H NMR, 13C NMR, 2D NMR and ESI MS methods. These studies provided evidence that the proton from the carboxylic group of salinomycin (SAL) is transferred to the amine group of benzylamine (BnA) forming the host-guest complex (SAL-BnA). It was shown that the SAL-BnA complex both in solid state and in chloroform solution is stabilized by the intramolecular O-H⋯O hydrogen bonds and also by the intermolecular hydrogen bonding interactions of the carboxylate, ketone and/or hydroxyl groups of SAL with water molecules present in the investigated system. The solvated acetonitrile molecules are additionally located in the voids between the SAL-BnA complex molecules in the crystal structure, while water molecules involved in the dihydrated crystalline SAL-BnA complex partially move into the solvent upon dissolution in chloroform.

Cynodon dactylon extract as a preventive and curative agent in experimentally induced nephrolithiasis.

PubMed

Atmani, F; Sadki, C; Aziz, M; Mimouni, M; Hacht, B

2009-04-01

Cynodon dactylon (Poaceae family) decoction was used in the treatment of kidney stones. However, no scientific study was undertaken so far to demonstrate the beneficial effect of the plant. Thus, the aim of the current study is to evaluate the effect of Cynodon aqueous extract as a preventive and curative agent in experimentally induced nephrolithiasis in a rat model. Ethylene glycol (EG) was used in the experiment to induce calcium oxalate (CaOx) deposition into kidneys. In preventive protocol, Cynodon decoction was administered in the same day with EG to evaluate the ability of the extract to prevent crystal deposition. However, in curative protocol, rats were first rendered nephrolithiasic and then the extract was administered to assess the ability of the plant to eliminate the pre-existing crystal deposition. In both protocols, urinary biochemical and other variables were measured during the course of the study. Crystalluria and renal histology were examined as well. The results showed that, in both protocols, all measured variables were similar for both the rat groups. Nevertheless, urinary biochemical analysis was apparently unaffected by the extract except oxalate in preventive protocol, and calcium, sodium, and potassium in curative protocol which were significantly highly excreted in treated rats compared to untreated animals. Crystalluria was characterized mostly by the presence of large quantities of CaOx monohydrate and CaOx dihydrate particles in untreated rats. However, crystalluria was mainly dominated by the presence of CaOx dihydrate particles with reduced size. The most apparent beneficial effect of Cynodon extract was seen in kidney tissues where reduced levels of CaOx deposition have been noticed especially in medullary and papillary sections from treated rats. We concluded that C. dactylon extract has beneficial effect in preventing and eliminating CaOx deposition into kidneys. Such findings provide a scientific explanation for its use in the treatment of kidneys stones.

Effect of citric acid on setting reaction and tissue response to β-TCP granular cement.

PubMed

Fukuda, Naoyuki; Tsuru, Kanji; Mori, Yoshihide; Ishikawa, Kunio

2017-02-24

We recently reported that when an acidic calcium phosphate solution is mixed with β-tricalcium phosphate (β-TCP) granules, the resulting dicalcium phosphate dihydrate (DCPD) crystals form bridges between the β-TCP granules, creating a set interconnected porous structure in approximately 1 min. Although this self-setting β-TCP granular cement (β-TCPGC) is useful for clinical applications, the short setting time is a key drawback for handling. In this study, the setting time of β-TCPGC was adjusted with the addition of citric acid, which is a known inhibiter of DCPD crystal growth. As the concentration of citric acid in the acidic calcium phosphate solution increased, the amount of DCPD formation in the set β-TCPGC decreased, and the crystal morphology of DCPD became elongated. β-TCPGC prepared with various citric acid concentrations were used as grafting material in rat calvarial bone defects to evaluate bone regeneration in vivo. Four weeks after implantation, no inflammatory reaction and approximately 20% new bone formation were observed, regardless of the presence or absence of citric acid in the liquid phase of β-TCPGC. We concluded, therefore, that citric acid might be a useful retarder of β-TCPGC setting times.

Synthesis, crystal structure, vibrational spectroscopy and photoluminescence of new hybrid compound containing chlorate anions of stanate (II)

NASA Astrophysics Data System (ADS)

Lassoued, Mohamed Saber; Abdelbaky, Mohammed S. M.; Lassoued, Abdelmajid; Meroño, Rafael Mendoza; Gadri, Abdellatif; Ammar, Salah; Ben Salah, Abdelhamid; García-Granda, Santiago

2017-08-01

The present work aimed at studying a new organic-inorganic bis (4-amino quinolinium) hexachloro stanate (II) dihydrate compound. It was prepared and characterized by single crystal X-ray diffraction, X-ray powder, Hirshfeld surface, Spectroscopy measurement, thermal study and photoluminescence properties. It was found to crystallize in the monoclinic system (P21/c space group) with the following lattice parameters: a = 7.2558(6) Å, b = 13.4876(5) Å, c = 17.2107(13) Å, β = 102.028 (12)°. Its crystal structure was determined and refined down to an R value of 0.06 and a wR value of 0.087. The structure consisted of two different alternating organic-inorganic layers. The crystal packing was stabilized by Nsbnd H⋯Cl and Osbnd H⋯Cl hydrogen bonds and π-π interactions. Hirshfeld surface analysis was used to investigate intermolecular interactions, as well 2D finger plots were conducted to reveal the contribution of these interactions in the crystal structure quantitatively. The X-ray powder is in agreement with the X-ray structure. Scanning electronic microscopy (SEM) was carried out. Furthermore, the room temperature Infra Red (IR) spectrum of the title compound was analyzed on the basis of data found in the literature. Solid state 13C NMR spectrum shows ten signals, confirming the solid state structure determined by X-ray diffraction. Thermal analysis shows two anomalies at 380 and 610 °C. The optical properties of the crystal were studied using optical absorption UV-visible and photoluminescence (PL) spectroscopy, which were investigated at room temperature.

Physicochemical and crystal structure analyses of the antidiabetic agent troglitazone.

PubMed

Kobayashi, Katsuhiro; Fukuhara, Hiroshi; Hata, Tadashi; Sekine, Akiko; Uekusa, Hidehiro; Ohashi, Yuji

2003-07-01

The antidiabetic agent troglitazone has two asymmetric carbons located at the chroman ring and the thiazolidine ring and is produced as a mixture of equal amounts of four optical isomers, 2R-5S, 2S-5R, 2R-5R, and 2S-5S. The crystalline powdered drug substance consists of two diastereomer pairs, 2R-5R/2S-5S and 2R-5S/2S-5R. There are many types of crystals obtained from various crystallization conditions. The X-ray structure analysis and the physicochemical analyses of troglitazone were performed. The solvated crystals of the 2R-5R/2S-5S pair were crystallized from several solutions: methanol, ethanol, acetonitrile, and dichloromethane. The ratio of solvent and troglitazone was 1 : 2 (L1/2-form). The monohydrate crystals were obtained from aqueous acetone solution (L1-form). On the other hand, only an anhydrate crystal of the 2R-5S/2S-5R pair was crystallized from various solutions (H0-form). The dihydrous mixed crystal (MA2-form) was obtained from a mixture of the two diastereomer pairs of 2R-5R/2S-5S and 2R-5S/2S-5R in equal amounts by the slow evaporation of aqueous acetone solution. The crystal structure of the MA2-form is similar to the H0-form. When the MA2 crystal was kept under low humidity, it was converted into the dehydrated form (MA0-form) with retention of the single crystal form. The structure of the MA0-form is isomorphous to the H0-form. The MA2-form was converted into the MA0-form and vice versa with retention of the single crystal under low and high humidity, respectively. The crystallization and storage conditions of the drug substances were successfully analyzed.

Holistic and component plant phenotyping using temporal image sequence.

PubMed

Das Choudhury, Sruti; Bashyam, Srinidhi; Qiu, Yumou; Samal, Ashok; Awada, Tala

2018-01-01

Image-based plant phenotyping facilitates the extraction of traits noninvasively by analyzing large number of plants in a relatively short period of time. It has the potential to compute advanced phenotypes by considering the whole plant as a single object (holistic phenotypes) or as individual components, i.e., leaves and the stem (component phenotypes), to investigate the biophysical characteristics of the plants. The emergence timing, total number of leaves present at any point of time and the growth of individual leaves during vegetative stage life cycle of the maize plants are significant phenotypic expressions that best contribute to assess the plant vigor. However, image-based automated solution to this novel problem is yet to be explored. A set of new holistic and component phenotypes are introduced in this paper. To compute the component phenotypes, it is essential to detect the individual leaves and the stem. Thus, the paper introduces a novel method to reliably detect the leaves and the stem of the maize plants by analyzing 2-dimensional visible light image sequences captured from the side using a graph based approach. The total number of leaves are counted and the length of each leaf is measured for all images in the sequence to monitor leaf growth. To evaluate the performance of the proposed algorithm, we introduce University of Nebraska-Lincoln Component Plant Phenotyping Dataset (UNL-CPPD) and provide ground truth to facilitate new algorithm development and uniform comparison. The temporal variation of the component phenotypes regulated by genotypes and environment (i.e., greenhouse) are experimentally demonstrated for the maize plants on UNL-CPPD. Statistical models are applied to analyze the greenhouse environment impact and demonstrate the genetic regulation of the temporal variation of the holistic phenotypes on the public dataset called Panicoid Phenomap-1. The central contribution of the paper is a novel computer vision based algorithm for automated detection of individual leaves and the stem to compute new component phenotypes along with a public release of a benchmark dataset, i.e., UNL-CPPD. Detailed experimental analyses are performed to demonstrate the temporal variation of the holistic and component phenotypes in maize regulated by environment and genetic variation with a discussion on their significance in the context of plant science.

Crystallization of calcium oxalates is controlled by molecular hydrophilicity and specific polyanion-crystal interactions.

PubMed

Grohe, Bernd; Taller, Adam; Vincent, Peter L; Tieu, Long D; Rogers, Kem A; Heiss, Alexander; Sørensen, Esben S; Mittler, Silvia; Goldberg, Harvey A; Hunter, Graeme K

2009-10-06

To gain more insight into protein structure-function relationships that govern ectopic biomineralization processes in kidney stone formation, we have studied the ability of urinary proteins (Tamm-Horsfall protein, osteopontin (OPN), prothrombin fragment 1 (PTF1), bikunin, lysozyme, albumin, fetuin-A), and model compounds (a bikunin fragment, recombinant-, milk-, bone osteopontin, poly-L-aspartic acid (poly asp), poly-L-glutamic acid (poly glu)) in modulating precipitation reactions of kidney stone-related calcium oxalate mono- and dihydrates (COM, COD). Combining scanning confocal microscopy and fluorescence imaging, we determined the crystal faces of COM with which these polypeptides interact; using scanning electron microscopy, we characterized their effects on crystal habits and precipitated volumes. Our findings demonstrate that polypeptide adsorption to COM crystals is dictated first by the polypeptide's affinity for the crystal followed by its preference for a crystal face: basic and relatively hydrophobic macromolecules show no adsorption, while acidic and more hydrophilic polypeptides adsorb either nonspecifically to all faces of COM or preferentially to {100}/{121} edges and {100} faces. However, investigating calcium oxalates grown in the presence of these polypeptides showed that some acidic proteins that adsorb to crystals do not affect crystallization, even if present in excess of physiological concentrations. These proteins (albumin, bikunin, PTF1, recombinant OPN) have estimated total hydrophilicities from 200 to 850 kJ/mol and net negative charges from -9 to -35, perhaps representing a "window" in which proteins adsorb and coat urinary crystals (support of excretion) without affecting crystallization. Strongest effects on crystallization were observed for polypeptides that are either highly hydrophilic (>950 kJ/mol) and highly carboxylated (poly asp, poly glu), or else highly hydrophilic and highly phosphorylated (native OPN isoforms), suggesting that highly hydrophilic proteins strongly affect precipitation processes in the urinary tract. Therefore, the level of hydrophilicity and net charge is a critical factor in the ability of polypeptides to affect crystallization and to regulate biomineralization processes.

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2014 CFR

2014-04-01

.... 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-69-1) is the chloride salt of metallic tin that contains two molecules of water. It is prepared from...

Isothermal Decomposition of Hydrogen Peroxide Dihydrate

NASA Technical Reports Server (NTRS)

Loeffler, M. J.; Baragiola, R. A.

2011-01-01

We present a new method of growing pure solid hydrogen peroxide in an ultra high vacuum environment and apply it to determine thermal stability of the dihydrate compound that forms when water and hydrogen peroxide are mixed at low temperatures. Using infrared spectroscopy and thermogravimetric analysis, we quantified the isothermal decomposition of the metastable dihydrate at 151.6 K. This decomposition occurs by fractional distillation through the preferential sublimation of water, which leads to the formation of pure hydrogen peroxide. The results imply that in an astronomical environment where condensed mixtures of H2O2 and H2O are shielded from radiolytic decomposition and warmed to temperatures where sublimation is significant, highly concentrated or even pure hydrogen peroxide may form.

Free energy of formation of a crystal nucleus in incongruent solidification: Implication for modeling the crystallization of aqueous nitric acid droplets in polar stratospheric clouds

NASA Astrophysics Data System (ADS)

Djikaev, Yuri S.; Ruckenstein, Eli

2017-04-01

Using the formalism of classical thermodynamics in the framework of the classical nucleation theory, we derive an expression for the reversible work W* of formation of a binary crystal nucleus in a liquid binary solution of non-stoichiometric composition (incongruent crystallization). Applied to the crystallization of aqueous nitric acid droplets, the new expression more adequately takes account of the effects of nitric acid vapor compared to the conventional expression of MacKenzie, Kulmala, Laaksonen, and Vesala (MKLV) [J. Geophys. Res.: Atmos. 102, 19729 (1997)]. The predictions of both MKLV and modified expressions for the average liquid-solid interfacial tension σls of nitric acid dihydrate (NAD) crystals are compared by using existing experimental data on the incongruent crystallization of aqueous nitric acid droplets of composition relevant to polar stratospheric clouds (PSCs). The predictions for σls based on the MKLV expression are higher by about 5% compared to predictions based on our modified expression. This results in similar differences between the predictions of both expressions for the solid-vapor interfacial tension σsv of NAD crystal nuclei. The latter can be obtained by using the method based on the analysis of experimental data on crystal nucleation rates in aqueous nitric acid droplets; it exploits the dominance of the surface-stimulated mode of crystal nucleation in small droplets and its negligibility in large ones. Applying that method to existing experimental data, our expression for the free energy of formation provides an estimate for σsv of NAD in the range ≈92 dyn/cm to ≈100 dyn/cm, while the MKLV expression predicts it in the range ≈95 dyn/cm to ≈105 dyn/cm. The predictions of both expressions for W* become identical for the case of congruent crystallization; this was also demonstrated by applying our method for determining σsv to the nucleation of nitric acid trihydrate crystals in PSC droplets of stoichiometric composition.

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2010 CFR

2010-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-0969-091) is the chloride salt of metallic tin that contains two...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2013 CFR

2013-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-69-1) is the chloride salt of metallic tin that contains two...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-0969-091) is the chloride salt of metallic tin that contains two...

21 CFR 184.1845 - Stannous chloride (anhydrous and dihydrated).

Code of Federal Regulations, 2012 CFR

2012-04-01

.... Anhydrous stannous chloride (SnCl2, CAS Reg. No. 7772-99-8) is the chloride salt of metallic tin. It is prepared by reacting molten tin with either chlorine or gaseous tin tetrachloride. Dihydrated stannous chloride (SnCl2·2H2O, CAS Reg. No. 10025-69-1) is the chloride salt of metallic tin that contains two...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sundaramurthi, Prakash; Suryanarayanan, Raj

To effectively inhibit succinate buffer crystallization and the consequent pH changes in frozen solutions. Using differential scanning calorimetry (DSC) and X-ray diffractometry (XRD), the crystallization behavior of succinate buffer in the presence of either (i) a crystallizing (glycine, mannitol, trehalose) or (ii) a non-crystallizing cosolute (sucrose) was evaluated. Aqueous succinate buffer solutions, 50 or 200 mM, at pH values 4.0 or 6.0 were cooled from room temperature to -25 C at 0.5 C/min. The pH of the solution was measured as a function of temperature using a probe designed to function at low temperatures. The final lyophiles prepared from thesemore » solutions were characterized using synchrotron radiation. When the succinic acid solution buffered to pH 4.0, in the absence of a cosolute, was cooled, there was a pronounced shift in the freeze-concentrate pH. Glycine and mannitol, which have a tendency to crystallize in frozen solutions, remained amorphous when the initial pH was 6.0. Under this condition, they also inhibited buffer crystallization and prevented pH change. At pH 4.0 (50 mM initial concentration), glycine and mannitol crystallized and did not prevent pH change in frozen solutions. While sucrose, a non-crystallizing cosolute, did not completely prevent buffer crystallization, the extent of crystallization was reduced. Sucrose decomposition, based on XRD peaks attributable to {beta}-D-glucose, was observed in frozen buffer solutions with an initial pH of 4.0. Trehalose completely inhibited crystallization of the buffer components when the initial pH was 6.0 but not at pH 4.0. At the lower pH, the crystallization of both trehalose dihydrate and buffer components was evident. When retained amorphous, sucrose and trehalose effectively inhibited succinate buffer component crystallization and the consequent pH shift. However, when trehalose crystallized or sucrose degraded to yield a crystalline decomposition product, crystallization of buffer was observed. Similarly, glycine and mannitol, two widely used bulking agents, inhibited buffer component crystallization only when retained amorphous. In addition to stabilizing the active pharmaceutical ingredient, lyoprotectants may prevent solution pH shift by inhibiting buffer crystallization.« less

Optical Simulation and Fabrication of Pancharatnam (Geometric) Phase Devices from Liquid Crystals

NASA Astrophysics Data System (ADS)

Gao, Kun

Pancharatnam made clear the concept of a phase-only device based on changes in the polarization state of light. A device of this type is sometimes called a circular polarization grating because of the polarization states of interfering light beams used to fabricate it by polarization holography. Here, we will call it a Pancharatnam (geometric) phase device to emphasize the fact that the phase of diffracted light does not have a discontinuous periodic profile but changes continuously. In this dissertation, using simulations and experiments, we have successfully demonstrated a 90% diffraction efficiency based on the Pancharatnam phase deflector (PPD) with the dual-twist structure. Unlike the conventional Pancharatnam phase deflector (c-PPD) limited to small diffraction angles, our work demonstrates that a device with a structural periodicity near the wavelength of light is highly efficient at deflecting light to large angles. Also, from a similar fabrication procedure, we have made an ultra-compact non-mechanical zoom lens system based on the Pancharatnam phase lens (PPL) with a low f-number and high efficiency. The wavelength dependence on the image quality is evaluated and shown to be satisfactory from red light to near-infrared machine vision systems. A demonstration device is shown with a 4x zoom ratio at a 633 nm wavelength. The unique characteristic of these devices is made possible through the use of azo-dye photoalignment materials to align a liquid crystal polymer (reactive mesogens). Furthermore, the proposed dual-twist design and fabrication opens the possibility for making a high-efficiency beam-steering device, a lens with an f-number less than 1.0, as well as a wide range of other potential applications in the optical and display industry. The details of simulation, fabrication, and characterization of these devices are shown in this dissertation.

Synthesis, characterization, and thermal analysis of a new energetic salt based on 1'-hydroxy-1H,1'H-5,5'-bitetrazol-1-olate

NASA Astrophysics Data System (ADS)

Niu, Chunhuan; Jin, Bo; Shang, Yu; Liu, Qiangqiang; Peng, Rufang

2018-04-01

4-Amino-1,2,4-triazolium 1'-hydroxy-1H,1'H-5,5'-bitetrazol-1-olate (ATHBTO) was synthesized by reacting 4-amino-1,2,4-triazole (AT) and 1H,1‧H-5,5‧-bistetrazole-1,1‧-diolate dihydrate (H2BTO.2H2O). Its crystal structure was characterized through single-crystal X-ray diffraction. Meanwhile, FTIR, 1H NMR, 13C NMR, and elemental analysis were also introduced to analyze its composition. The thermal stability was investigated by differential scanning calorimetry, thermogravimetric analysis, and thermogravimetric tandem infrared spectrum. Results indicated that ATHBTO exhibited excellent resistance to thermal decompositions reaching 511.4 K and had a 64.6% mass loss between 475.7 and 552.3 K. The kinetics parameters were calculated by Kissinger's method and Ozawa-Doyle's method. Moreover, according to the Kamlet-Jacobs formula, the calculated detonation velocity and detonation pressure of ATHBTO attained 8218 m/s and 28.69 GPa, respectively.

Synthesis, self-assembly, and properties of Mn doped ZnO nanoparticles.

PubMed

Barick, K C; Bahadur, D

2007-06-01

We report here a novel process to prepare Mn doped ZnO nanoparticles by a soft chemical route at low temperature. The synthesis process is based on the hydrolysis of zinc acetate dihydrate and manganese acetate tetrahydrate heated under reflux to 160-175 degrees C using diethylene glycol as a solvent. X-ray diffraction analysis reveals that the Mn doped ZnO crystallizes in a wurtzite structure with crystal size of 15-25 nm. These nano size crystallites of Mn doped ZnO self-organize into polydisperse spheres in size ranging from 100-400 nm. Transmission Electron Microscopy image also shows that each sphere is made up of numerous nanocrystals of average diameter 15-25 nm. By means of X-ray photoelectron spectroscopy and electron spin resonance spectroscopy, we determined the valence state of Mn ions as 2+. These nanoparticles were found to be ferromagnetic at room temperature. Monodisperse porous spheres (approximately 250 nm) were obtained by size selective separation technique and then self-assembled in a closed pack periodic array through sedimentation with slow solvent evaporation, which gives strong opalescence in visible region.

Inhibition of the solid state transformation of carbamazepine in aqueous solution: impact of polymeric properties.

PubMed

Gift, Alan D; Hettenbaugh, Jacob A; Quandahl, Rachel A; Mapes, Madison

2017-11-06

The effects of polymers on the anhydrate-to-hydrate transformation of carbamazepine (CBZ) was investigated. The three types of polymers studied were polyvinylpyrrolidone (PVP), polyvinyl alcohol (PVA) and substituted celluloses which included hydroxypropyl methylcellulose (HPMC) and methylcellulose (MC). Anhydrous CBZ was added to dilute aqueous polymer solutions and Raman spectroscopy measurements were collected to monitor the kinetics of the solution-mediated transformation to CBZ dihydrate. Polymers exhibiting the greatest inhibition were able to reduce the growth phase of the solution-mediated transformation and change the habit of the hydrate crystal indicating polymer adsorption to the hydrate crystal surface as the mechanism of inhibition. The results of the various polymers showed that short chain substituted celluloses (HPMC and MC) inhibited the CBZ transformation to a much greater extent than longer chains. The same trend was observed for PVP and PVA, but to a lesser extent. These chain length effects were attributed to changes in polymer confirmation when adsorbed on the crystal surface. Additionally, decreasing the percentage of hydroxyl groups on the PVA polymer backbone reduced the ability of the polymer to inhibit the transformation and changing the degree of substitutions of methyl and hydroxypropyl groups on the cellulosic polymer backbone had no effect on the transformation.

A new supramolecular chromium(III) complex: Synthesis, structural determination, optical study, magnetic and antibacterial activity

NASA Astrophysics Data System (ADS)

Dridi, Rihab; Dhieb, Cyrine; Cherni, Saoussen Namouchi; Boudjada, Nassira Chniba; Sadfi Zouaoui, Najla; Zid, Mohamed Faouzi

2018-01-01

A new chromium (III) complex 1,5-Naphthyridine Trans-diaquadioxalatochromate (III) dihydrate, had been synthesized by self-assembly of chromium (III) nitrate with oxalic acid and 1,5-Naphthyridine. The complex was characterized by X-ray diffraction, Fourier Transform Infrared spectroscopy, thermogravimetric analysis and UV-Visible spectroscopy. The crystal morphology was carried out using Bravais-Friedel-Donnay-Harker (BFDH) model. Single crystal X-Ray structure determination revealed that the complex posses two crystallographically independent Cr(III) centers. Each Cr(III) has a distorted octahedron geometry involving two axial O atoms from two water molecules and four equatorial O atoms from two oxalate dianions forming trans-[Cr(C2O4)2(H2O)2]- complex anions. The charge compensation is accomplished by the incorporation of 1,5-Naphthyridine cations. Connection between these entities is ensured by means of strong hydrogen bonds giving rise to 3D supramolecular architecture. Hirshfeld surface analysis and the related 2D fingerprint plots were used for decoding plausible intermolecular interactions in the crystal packing. The magnetic properties of the complex had been investigated and discussed in the context of its structure. The antimicrobial activity was evaluated by disc diffusion method highlighting an antagonistic effect of the synthesized complex against Gram-positive and Gram-negative species.

Solid-vapor interactions: influence of environmental conditions on the dehydration of carbamazepine dihydrate.

PubMed

Surana, Rahul; Pyne, Abira; Suryanarayanan, Raj

2004-12-31

The goal of this research was a phenomenological study of the effect of environmental factors on the dehydration behavior of carbamazepine dihydrate. Dehydration experiments were performed in an automated vapor sorption apparatus under a variety of conditions, and weight loss was monitored as a function of time. In addition to lattice water, carbamazepine dihydrate contained a significant amount of physically bound water. Based on the kinetics of water loss, it was possible to differentiate between the removal of physically bound water and the lattice water. The activation energy for the 2 processes was 44 and 88 kJ/mol, respectively. As expected, the dehydration rate of carbamazepine dihydrate decreased with an increase in water vapor pressure. While dehydration at 0% relative humidity (RH) resulted in an amorphous anhydrate, the crystallinity of the anhydrate increased as a function of the RH of dehydration. A method was developed for in situ crystallinity determination of the anhydrate formed. Dehydration in the presence of the ethanol vapor was a 2-step process, and the fraction dehydrated at each step was a function of the ethanol vapor pressure. We hypothesize the formation of an intermediate lower hydrate phase with unknown water stoichiometry. An increase in the ethanol vapor pressure first led to a decrease in the dehydration rate followed by an increase. In summary, the dehydration behavior of carbamazepine dihydrate was evaluated at different vapor pressures of water and ethanol. Using the water sorption apparatus, it was possible to (1) differentiate between the removal of physically bound and lattice water, and (2) develop a method for quantifying, in situ, the crystallinity of the product (anhydrate) phase.

Correlation of Periodontal Disease With Inflammatory Arthritis in the Time Before Modern Medical Intervention.

PubMed

Rothschild, Bruce

2017-03-01

Controversy exists regarding possible correlation of periodontal disease with rheumatoid arthritis (RA) and ankylosing spondylitis (AS). Confounding factors may relate to stringency of inflammatory disease diagnosis and the effect of therapeutic intervention for RA on periodontal disease. These factors are investigated in this study. Forty-five individuals with documented RA (n = 15), spondyloarthropathy (n = 15), and calcium pyrophosphate deposition disease (CPPD) (n = 15), from the Hamann-Todd collection of human skeletons compiled from 1912 to 1938, and 15 individuals contemporarily incorporated in the collection were examined for tooth loss, cavity occurrence, average and maximum lingual and buccal depth of space between tooth and bone, periosteal reaction, serpentine bone resorption, abscess formation, and root penetration of the bone surface and analyzed by analysis of variance. Tooth loss was common, but actual number of teeth lost, cavity occurrence, average and maximum lingual and buccal depth of space between tooth and bone, periosteal reaction, serpentine grooving surrounding teeth (considered a sign of inflammation), abscess formation, and root exposure (penetration of bone surface) were indistinguishable among controls and individuals with RA, spondyloarthropathy, and CPPD. Although many factors can affect periodontal disease, presence of inflammatory arthritis does not appear to be one of them. The implication is that dental disease was common in the general population and not necessarily associated with arthritis, at least before the advent of modern rheumatologic medications. As specific diagnosis did not affect prevalence, perhaps current prevalence controversy may relate to current intervention, a subject for further study.

A Neat Trick Using Oxalic Acid Dihydrate and Potassium Permanganate and Other Experiments with Small Organic Amine or Oxygenated Compounds

ERIC Educational Resources Information Center

Kelland, Malcolm A.

2011-01-01

Solid potassium permanganate (KMnO[subscript 4]) is shown to react in a variety of ways with small organic amines or oxygenated compounds depending on whether they are liquids or solids and whether water is present. In particular, its reaction with solid oxalic acid dihydrate can be initiated by the moisture in one's breath, making an intriguing…

Spectroscopic study of the inhibition of calcium oxalate calculi by Larrea tridentata

NASA Astrophysics Data System (ADS)

Pinales, Luis Alonso

The causes of urolithiasis include such influences as diet, metabolic disorders, and genetic factors which have been documented as sources that aggravate urinary calculi depositions and aggregations, and, implicitly, as causes of urolithiasis. This study endeavors to detail the scientific mechanisms involved in calcium oxalate calculi formation, and, more importantly, their inhibition under growth conditions imposed by the traditional medicinal approach using the herbal extract, Larrea tridentata. The calculi were synthesized without and with Larrea tridentata infusion by employing the single diffusion gel technique. A visible decrease in calcium oxalate crystal growth with increasing amounts of Larrea tridentata herbal infusion was observed in photomicrographs, as well as a color change from white-transparent for pure crystals to light orange-brown for crystals with inhibitor. Analysis of the samples, which includes Raman, infrared absorption, scanning electron microscopy (SEM), and X-ray powder diffraction (XRD) techniques, demonstrate an overall transition in morphology of the crystals from monohydrate without herbal extract to dihydrate with inhibitor. Furthermore, the resulting data from Raman and infrared absorption support the possibilities of the influences, in this complex process, of NDGA and its derivative compounds from Larrea tridentata, and of the bonding of the magnesium of the inhibitor with the oxalate ion on the surface of the calculi crystals. This assumption corroborates well with the micrographs obtained under higher magnification, which show that the separated small crystallites consist of darker brownish cores, which we attribute to the dominance of growth inhibition by NDGA, surrounded by light transparent thin shells, which possibly correspond to passivation of the crystals by magnesium oxalate. The SEM results reveal the transformation from the dominant monoclinic structure of the calcium oxalate crystals grown alone to the tetragonal dipyramidal crystal structure of the calcium oxalate crystals grown with Larrea tridentata. Comparison between XRD experimental and simulated data, besides corroborating with our previous results, show that each sample is a combination of different structures.

Role of scanning electron microscopy in identifying drugs used in medical practice.

PubMed

Fazil Marickar, Y M; Sylaja, N; Koshy, Peter

2009-10-01

Several plant preparations are administered for treatment of stone disease without scientific basis. This paper presents the results of in vitro and animal experimental studies using scanning electron microscopy (SEM) in the identification of the therapeutic properties of trial drugs in medicine. In the first set of the study, urinary crystals namely calcium oxalate monohydrate and calcium oxalate dehydrate were grown in six sets of Hane's tubes in silica gel medium. Trial drugs namely scoparia dulcis Lynn, musa sapiens and dolicos biflorus were incorporated in the gel medium to identify the dopant effect of the trial drugs on the size and extent of crystal column growth. The changes in morphology of crystals were studied using SEM. In the second set, six male Wistar rats each were calculogenised by administering sodium oxalate and ethylene glycol and diabetised using streptozotocin. The SEM changes of calculogenisation were studied. The rats were administered trial drugs before calculogenisation or after. The kidneys of the rats studied under the scanning electron microscope showed changes in tissue morphology and crystal deposition produced by calculogenisation and alterations produced by addition of trial drugs. The trial drugs produced changes in the pattern of crystal growth and in the crystal morphology of both calcium oxalate monohydrate and calcium oxalate dihydrate grown in vitro. Elemental distribution analysis showed that the crystal purity was not altered by the trial drugs. Scoparia dulcis Lynn was found to be the most effective anticalculogenic agent. Musa sapiens and dolicos biflorus were found to have no significant effect in inhibiting crystal growth. The kidneys of rats on calculogenisation showed different grades of crystals in the glomerulus and interstitial tissues, extrusion of the crystals into the tubular lumen, collodisation and tissue inflammatory cell infiltration. Scoparia dulcis Lynn exhibited maximum protector effect against the changes of calculogenisation. Musa sapiens and dolicos biflorus had only minimal effect in preventing crystal deposition, inflammatory cell infiltration and other changes of calculogenisation. SEM was found to be effective in assessing the effect of drugs on crystal growth morphology and tissue histology.

Lanthanide Fluorobenzoates as Bio-Probes: a Quest for the Optimal Ligand Fluorination Degree.

PubMed

Kalyakina, Alena S; Utochnikova, Valentina V; Bushmarinov, Ivan S; Le-Deygen, Irina M; Volz, Daniel; Weis, Patrick; Schepers, Ute; Kuzmina, Natalia P; Bräse, Stefan

2017-10-20

The thorough study of fluorinated benzoates of lanthanides (Eu, Tb, Nd, Er, Yb, Gd, La, Lu) is reported. Their composition in single crystal and powder state revealed two predominant structural motifs. An in-depth luminescence study has been performed on the reported fluorobenzoates, showing, that terbium and europium complexes in solid state possess high luminescence intensity with the quantum yield of up to 69 %. High solubility in most organic solvents, as well as in water, combined with the high luminescence intensity in water solution and non-toxicity allowed the testing of europium complexes as bioprobes in cellulo. Among all tested fluorobenzoates, europium 2-fluorobenzoate dihydrate combined the best luminescent properties, thermodynamic stability, aqueous solubility, and non-toxicity, and was shown to be a viable bio-marker. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Distribution of organic matrix in calcium oxalate renal calculi.

PubMed

Warpehoski, M A; Buscemi, P J; Osborn, D C; Finlayson, B; Goldberg, E P

1981-01-01

The quantity of protein and carbohydrate comprising the matrix of calcium oxalate monohydrate (COM) renal stones was found to decrease with distance from the surface of the stone. The average organic concentration of stones 3 to 30 mm in diameter ranged from 5.7% at the surface to 2.7% at the core. This concentration gradient suggests matrix involvement in a "growth front" on stone surfaces with migration of organic material from the "older" interior. The matrix distribution was not readily correlated with density variations or with the presence of hydroxyapatite or calcium oxalate dihydrate. Surface matrix concentrations were greater than amounts predicted by physical adsorption. Electron microscopy confirmed the presence of the organic-rich surface layer and also suggested that increase in stone size occurs predominantly by crystal growth with microcrystal aggregates as growth centers.

High pressure cosmochemistry of major planetary interiors: Laboratory studies of the water-rich region of the system ammonia-water

NASA Technical Reports Server (NTRS)

Nicol, Malcolm; Johnson, Mary; Boone, Steven; Cynn, Hyunchee

1987-01-01

Several studies relative to high pressure cosmochemistry of major planetary interiors are summarized. The behavior of gas-ice mixtures at very high pressures, studies of the phase diagram of (NH3) sub x (H2O) sub 1-x at pressures to 5GPa and temperatures from 240 to 370 K, single crystal growth of ammonia dihydrate at room temperature in order to determine their structures by x-ray diffraction, spectroscopy of chemical reactions during shock compression in order to evaluate how the reactions affect the interpretation of equation of state data obtained by shock methods, and temperature and x-ray diffraction measurements made on resistively heated wire in diamond anvil cells in order to obtain phase and structural data relevant to the interiors of terrestrial planets are among the studies discussed.

Evaluation of Gum of Moringa oleifera as a Binder and Release Retardant in Tablet Formulation

PubMed Central

Panda, D. S.; Choudhury, N. S. K.; Yedukondalu, M.; Si, S.; Gupta, R.

2008-01-01

The present study was undertaken to find out the potential of gum from Moringa oleifera to act as a binder and release retardant in tablet formulations. The effect of calcium sulphate dihydrate (water insoluble) and lactose (water soluble) diluent on the release of propranolol hydrochloride was studied. The DSC thermograms of drug, gum and mixture of gum/drug indicated no chemical interaction. Tablets (F1, F2, F3, and F4) were prepared containing calcium sulphate dihydrate as diluent, propranolol hydrochloride as model drug using 10%, 8%, 6% and 4% w/v of gum solution as binder. Magnesium stearate was used as lubricant. Physical and technological properties of granules and tablets like flow rate, Carr index, Hausner ratio, angle of repose, hardness, friability and disintegration time were determined and found to be satisfactory. Tablets were prepared by wet granulation method containing calcium sulphate dihydrate as excipient, propranolol hydrochloride as model drug using 10%, 20% and 30% of gum as release retardant, magnesium stearate was used as lubricant. Similarly tablets were prepared replacing lactose with calcium sulphate dihydrate. Despite of the widely varying physico-chemical characteristics of the excipients, the drug release profiles were found to be similar. The drug release increased with increasing proportions of the excipient and decreased proportion of the gum irrespective of the solubility characteristics of the excipient. The values of release exponent ‘n’ are between 0.37 and 0.54. This implies that the release mechanism is Fickian. There is no evidence that the dissolution or erosion of the excipient has got any effect on the release of the drug. The t50% values for tablets containing calcium sulphate dihydrate were on an average 10%-15% longer than the tablets containing lactose as excipient. These relatively small differences in t50% values suggest that the nature of excipient used appeared to play a minor role in regulating the release, while the gum content was a major factor. PMID:21394258

Calcium phosphates recovery from digester supernatant by fast precipitation and recrystallization

NASA Astrophysics Data System (ADS)

Vasenko, Liubov; Qu, Haiyan

2018-01-01

Conditional solubility of dicalcium phosphate dihydrate (DCPD) and hydroxyapatite (HAp) in digester supernatant was determined as a function of pH and was compared to its conditional solubility in distilled water. Conditional solubility of both substances in digester supernatant at pH >5-6 was higher than their conditional solubility in pure water due to the presence of impurities, and this influence is more significant for HAp. Amorphous CaP was precipitated through a fast precipitation process from digester supernatant with initial total phosphate concentration 0.008 mol/L and 0.015 mol/L and Ca/P ratios 2 and 5. The amorphous CaP can be subsequently recrystallized into crystalline CaP. Obtained amorphous products have Ca/P ratio > 1, which allow performing the recrystallization process without further Ca dosing into the system. Batch recrystallization of the amorphous products resulted in crystallization of HAp, DCPD or their mixture depending on the conditions of the process. Maximum achieved P-recovery was 69.5%. The increase of phosphate concentration and the addition of seeding decreased the yield of the process but promoted crystallization of DCPD. The increase of Ca/P ratio had a positive effect on the total P-recovery. Compared with the direct batch crystallization of CaP from digester supernatant, the two-step process with fast precipitation and recrystallization significantly improved the color of the obtained products.

Revisiting spatial distribution and biochemical composition of calcium-containing crystals in human osteoarthritic articular cartilage.

PubMed

Nguyen, Christelle; Bazin, Dominique; Daudon, Michel; Chatron-Colliet, Aurore; Hannouche, Didier; Bianchi, Arnaud; Côme, Dominique; So, Alexander; Busso, Nathalie; Busso, Nathalie; Lioté, Frédéric; Ea, Hang-Korng

2013-01-01

Calcium-containing (CaC) crystals, including basic calcium phosphate (BCP) and calcium pyrophosphate dihydrate (CPP), are associated with destructive forms of osteoarthritis (OA). We assessed their distribution and biochemical and morphologic features in human knee OA cartilage. We prospectively included 20 patients who underwent total knee replacement (TKR) for primary OA. CaC crystal characterization and identification involved Fourier-transform infra-red spectrometry and scanning electron microscopy of 8 to 10 cartilage zones of each knee, including medial and lateral femoral condyles and tibial plateaux and the intercondyle zone. Differential expression of genes involved in the mineralization process between cartilage with and without calcification was assessed in samples from 8 different patients by RT-PCR. Immunohistochemistry and histology studies were performed in 6 different patients. Mean (SEM) age and body mass index of patients at the time of TKR was 74.6 (1.7) years and 28.1 (1.6) kg/m², respectively. Preoperative X-rays showed joint calcifications (chondrocalcinosis) in 4 cases only. The medial femoro-tibial compartment was the most severely affected in all cases, and mean (SEM) Kellgren-Lawrence score was 3.8 (0.1). All 20 OA cartilages showed CaC crystals. The mineral content represented 7.7% (8.1%) of the cartilage weight. All patients showed BCP crystals, which were associated with CPP crystals for 8 joints. CaC crystals were present in all knee joint compartments and in a mean of 4.6 (1.7) of the 8 studied areas. Crystal content was similar between superficial and deep layers and between medial and femoral compartments. BCP samples showed spherical structures, typical of biological apatite, and CPP samples showed rod-shaped or cubic structures. The expression of several genes involved in mineralization, including human homolog of progressive ankylosis, plasma-cell-membrane glycoprotein 1 and tissue-nonspecific alkaline phosphatase, was upregulated in OA chondrocytes isolated from CaC crystal-containing cartilages. CaC crystal deposition is a widespread phenomenon in human OA articular cartilage involving the entire knee cartilage including macroscopically normal and less weight-bearing zones. Cartilage calcification is associated with altered expression of genes involved in the mineralisation process.

A Raman spectroscopic study of thermally treated glushinskite--the natural magnesium oxalate dihydrate.

PubMed

Frost, Ray L; Adebajo, Moses; Weier, Matt L

2004-02-01

Raman spectroscopy has been used to study the thermal transformations of natural magnesium oxalate dihydrate known in mineralogy as glushinskite. The data obtained by Raman spectroscopy was supplemented with that of infrared emission spectroscopy. The vibrational spectroscopic data was complimented with high resolution thermogravimetric analysis combined with evolved gas mass spectrometry. TG-MS identified two mass loss steps at 146 and 397 degrees C. In the first mass loss step water is evolved only, in the second step carbon dioxide is evolved. The combination of Raman microscopy and a thermal stage clearly identifies the changes in the molecular structure with thermal treatment. Glushinskite is the dihydrate phase in the temperature range up to the pre-dehydration temperature of 146 degrees C. Above 397 degrees C, magnesium oxide is formed. Infrared emission spectroscopy shows that this mineral decomposes at around 400 degrees C. Changes in the position and intensity of the CO and CC stretching vibrations in the Raman spectra indicate the temperature range at which these phase changes occur.

(E)-N′-(4-Meth­oxy­benzyl­idene)pyridine-3-carbohydrazide dihydrate

PubMed Central

Novina, J. Josephine; Vasuki, G.; Suresh, M.; Padusha, M. Syed Ali

2013-01-01

In the title compound, C14H13N3O2·2H2O, the hydrazone mol­ecule adopts an E conformation with respect to the C=N bond. The dihedral angle between the benzene and pyridine rings is 8.55 (10)°. The methyl­idene–hydrazide [–C(=O)–N–N=C–] fragment is essentially planar, with a maximum deviation of 0.0375 (13) Å. The mean planes of the benzene and pyridine rings make dihedral angles of 2.71 (14) and 11.25 (13)°, respectively, with mean plane of the methyl­idene-hydrazide fragment. In the crystal, the benzohydrazide and water mol­ecules are linked by N—H⋯O, O—H⋯O and O—H⋯N hydrogen bonds into a three-dimensional network. PMID:24046719

The crystal and molecular structure of sodium 4-(2,4,6-triisopropylbenzoyl)benzoate in terms of the photochemical behaviour of the anion.

PubMed

Konieczny, Krzysztof; Bąkowicz, Julia; Turowska-Tyrk, Ilona

2015-05-01

Contrary to the known 4-(2,4,6-triisopropylbenzoyl)benzoate salts, di-μ-aqua-bis[tetraaquasodium(I)] bis[4-(2,4,6-triisopropylbenzoyl)benzoate] dihydrate, [Na2(H2O)10](C23H27O3)2·2H2O, (1), does not undergo a photochemical Norrish-Yang reaction in the crystalline state. In order to explain this photochemical inactivity, the intermolecular interactions were analyzed by means of the Hirshfeld surface and intramolecular geometrical parameters describing the possibility of a Norrish-Yang reaction were calculated. The reasons for the behaviour of the title salt are similar crystalline environments for both the o-isopropyl groups in the anion, resulting in similar geometrical parameters and orientations, and that these interaction distances differ significantly from those found in salts where the photochemical reaction occurs.

Infrared optical constants of H2O ice, amorphous nitric acid solutions, and nitric acid hydrates

NASA Technical Reports Server (NTRS)

Toon, Owen B.; Koehler, Birgit G.; Middlebrook, Ann M.; Tolbert, Margaret A.; Jordon, Joseph

1994-01-01

We determined the infrared optical constants of nitric acid trihydrate, nitric acid dihydrate, nitric acid monohydrate, and solid amorphous nitric acid solutions which crystallize to form these hydrates. We have also found the infrared optical constants of H2O ice. We measured the transmission of infrared light throught thin films of varying thickness over the frequency range from about 7000 to 500/cm at temperatures below 200 K. We developed a theory for the transmission of light through a substrate that has thin films on both sides. We used an iterative Kramers-Kronig technique to determine the optical constants which gave the best match between measured transmission spectra and those calculated for a variety of films of different thickness. These optical constants should be useful for calculations of the infrared spectrum of polar stratospheric clouds.

Properties of zinc tin oxide thin film by aerosol assisted chemical vapor deposition (AACVD)

NASA Astrophysics Data System (ADS)

Riza, Muhammad Arif; Rahman, Abu Bakar Abd; Sepeai, Suhaila; Ludin, Norasikin Ahmad; Teridi, Mohd Asri Mat; Ibrahim, Mohd Adib

2018-05-01

This study focuses on the properties of ZTO which have been deposited by a low-cost method namely aerosol assisted chemical vapor deposition (AACVD). The precursors used in this method were zinc acetate dihidrate and tin chloride dihydrate for ZTO thin film deposition. Both precursors were mixed and stirred until fully dissolved before deposition. The ZTO was deposited on borosilicate glass substrate for the investigation of optical properties. The films deposited have passed the scotch tape adherence test. XRD revealed that the crystal ZTO is slightly in the form of perovskite structure but several deteriorations were also seen in the spectrum. The UV-Vis analysis showed high transmittance of ˜85% and the band gap was calculated to be 3.85 eV. The average thickness of the film is around 284 nm. The results showed that the ZTO thin films have been successfully deposited by the utilization of AACVD method.

Polaron conductivity mechanism in oxalic acid dihydrate: ac conductivity experiment

NASA Astrophysics Data System (ADS)

Levstik, Adrijan; Filipič, Cene; Bobnar, Vid; Levstik, Iva; Hadži, Dušan

2006-10-01

The ac electrical conductivity of the oxalic acid dihydrate ( α -POX) was investigated as a function of the frequency and temperature. The real part of the complex ac electrical conductivity was found to follow the universal dielectric response σ'∝νs , indicating that hopping or tunneling of localized charge carriers governs the electrical transport. A detailed analysis of the temperature dependence of the exponent s revealed that in a broad temperature range 50-200K the tunneling of polarons is the dominating charge transport mechanism.

NTP toxicity studies of sodium dichromate dihydrate (CAS No. 7789-12-0) administered in drinking water to male and female F344/N rats and B6C3F1 mice and male BALB/c and am3-C57BL/6 mice.

PubMed

Bucher, John R

2007-01-01

Sodium dichromate dihydrate is one of a number of inorganic compounds containing hexavalent chromium (CR VI) found in drinking water supplies as a contaminant resulting from various industrial processes including electroplating operations, leather tanning, and textile manufacturing. Because of the lack of adequate experimental data on the toxicity and carcinogenicity of hexavalent chromium ingested orally, and because hexavalent chromium has been found in human drinking water supplies, the California Congressional delegation and the California Environmental Protection Agency nominated hexavalent chromium to the NTP for study. In study 1, male and female F344/N rats and B6C3F1 mice were exposed to sodium dichromate dihydrate (greater than 99% pure) in drinking water for 3 months. In study 2, sodium dichromate dihydrate was administered in drinking water to male B6C3F1, BALB/c, and am3-C57BL/6 mice for 3 months. Genetic toxicology studies were conducted in Salmonella typhimurium, Escherichia coli, and mouse peripheral blood erythrocytes. In study 1, groups of 10 male and 10 female F344/N rats and B6C3F1 mice were given drinking water containing 0, 62.5, 125, 250, 500, or 1,000 mg sodium dichromate dihydrate/L for 3 months (equivalent to average daily doses of approximately 5, 10, 17, 32, or 60 mg sodium dichromate dihydrate/kg body weight to rats and 9, 15, 26, 45, or 80 mg/kg to mice). On a molecular weight basis, these doses are equivalent to approximately 1.7, 3.5, 5.9, 11.2, and 20.9 mg hexavalent chromium/kg body weight per day to rats and 3.1, 5.2, 9.1, 15.7, and 27.9 mg/kg per day to mice. Additional groups of 10 rats per sex were exposed to the same concentrations of sodium dichromate dihydrate for 4 weeks. All rats and mice survived to the end of the study. Reduced body weights occurred in 500 and 1,000 mg/L male rats, 1,000 mg/L female rats, and in male and female mice exposed to 125 mg/L or greater. Water consumption by male and female rats exposed to 250 mg/L or greater and male and female mice exposed to 125 mg/L or greater was generally less than that by the control groups, and decreases in urine volume and increases in urine specific gravity in rats were related to reduced water consumption. Exposure to sodium dichromate dihydrate caused a microcytic hypochromic anemia in rats and mice, but the severity was less in mice. Serum cholesterol and triglyceride concentrations were decreased in rats. Increased bile acid concentrations in exposed groups of rats may have been due to altered hepatic function. The incidences of histiocytic cellular infiltration were generally significantly increased in the duodenum of rats and mice, the liver of female rats, and the mesenteric lymph node of mice exposed to 125 mg/L or greater. Significantly increased nonneoplastic lesions (focal ulceration, regenerative epithelial hyperplasia, and squamous epithelial metaplasia) occurred in the glandular stomach of male and female rats exposed to 1,000 mg/L. Incidences of epithelial hyperplasia of the duodenum were significantly increased in all exposed groups of mice. In study 2, sodium dichromate dihydrate was administered in drinking water to groups of 10 male B6C3F1, 10 male BALB/c, and five male am3-C57BL/6 mice for 3 months at exposure concentrations of 0, 62.5, 125, or 250 mg/L (equivalent to average daily doses of approximately 8, 15, or 25 mg/kg sodium dichromate dihydrate or 2.8, 5.2, or 8.7 mg/kg chromium to B6C3F1, BALB/c, and am3-C57BL/6 mice). All mice in study 2 survived until study termination. Mean body weights of 125 and 250 mg/L B6C3F1 and BALB/c mice and all exposed groups of am3-C57BL/6 mice were less than those of the control groups. Mice exposed to 250 mg/L consumed less water than the control groups. Exposure concentration-related decreases in mean red cell volumes and mean red cell hemoglobin values were observed in all three mouse strains. Erythrocyte counts were increased in exposed B6C3F1 and BALB/c mice but not in am3-C57BL/6 mice. Changes in organ weights were generally consistent with reduced body weights in exposed groups in all mouse strains. No biologically significant differences in reproductive parameters were observed in any strain. Histiocytic cellular infiltration and epithelial hyperplasia of the duodenum occurred in most mice exposed to 125 or 250 mg/L, and the incidences of these lesions were increased in the 62.5 mg/L group compared to controls. Secretory depletion was present in the pancreas of most mice exposed to 125 or 250 mg/L. The incidences of glycogen depletion of the liver were significantly increased in male B6C3F1 mice exposed to 125 or 250 mg/L and in all exposed groups of male am3-C57BL/6 mice. The incidence of histiocytic cellular infiltration in the mesenteric lymph node was significantly increased in the 250 mg/L group of male am3-C57BL/6 mice. Sodium dichromate dihydrate was mutagenic in S. typhimurium strains TA100 and TA98 and in E. coli strain WP2 uvrA pKM101 with and without induced rat liver S9 enzymes. The results of four micronucleus tests conducted in the three strains of mice from studies 1 and 2 were mixed. In study 1, no significant increases were seen in micronucleated normochromatic erythrocytes in peripheral blood samples from male or female B6C3F1 mice; there was a decrease in the percentage of polychromatic erythrocytes among total erythrocytes (an indication of bone marrow toxicity), but the changes were small and not well correlated with exposure concentrations. In study 2, a significant exposure concentration-related increase (P<0.001) in micronucleated normochromatic erythrocytes was seen in am3-C57BL/6 male mice. An equivocal increase in micronucleated erythrocytes was noted in male B6C3F1 mice, based on a small increase in micronucleated normochromatic erythrocytes that did not reach statistical significance. No increase in micronucleated normochromatic erythrocytes was observed in male BALB/c mice. No significant effect of sodium dichromate dihydrate exposure on the percentage of polychromatic erythrocytes was observed in any of the three micronucleus tests conducted in study 2. In summary, administration of sodium dichromate dihydrate in the drinking water to F344/N rats and B6C3F1 mice resulted in focal ulceration, hyperplasia, and metaplasia in the glandular stomach at the limiting ridge in rats in the 1,000 mg/L group and evidence of increased histiocytic infiltration in the liver (female), duodenum of the small intestine, and/or pancreatic lymph nodes at concentrations as low as 62.5 mg/L, the lowest concentration studied. In addition, a microcytic, hypochromic anemia occurred at all exposure concentrations and was considered evidence of a toxic response resulting from absorption of Cr VI following oral ingestion in rats. A similar, but less severe, anemia was evident in mice receiving drinking water containing sodium dichromate dihydrate; histiocytic infiltration was noted in the duodenum of all three strains studied (B6C3F1, BALB/c, and am3-C57BL/6) at all concentrations employed, in the mesenteric lymph nodes at 125 mg/L or greater in the B6C3F1 strain, and at 250 mg/L in the am3-C57BL/6 strain. There was no consistent evidence of hepatocyte injury in mice in any of the strains tested. Variations in glycogen content were considered more likely related to diminished food intake than to the toxicity of sodium dichromate dihydrate. Synonyms: Chromic acid; dichromic acid; disodium salt, dihydrate; disodium dichromate dihydrate; chromium VI.

Proteomic analysis of a rare urinary stone composed of calcium carbonate and calcium oxalate dihydrate: a case report.

PubMed

Kaneko, Kiyoko; Matsuta, Yosuke; Moriyama, Manabu; Yasuda, Makoto; Chishima, Noriharu; Yamaoka, Noriko; Fukuuchi, Tomoko; Miyazawa, Katsuhito; Suzuki, Koji

2014-03-01

The objective of the present study was to investigate the matrix protein of a rare urinary stone that contained calcium carbonate. A urinary stone was extracted from a 34-year-old male patient with metabolic alkalosis. After X-ray diffractometry and infrared analysis of the stone, proteomic analysis was carried out. The resulting mass spectra were evaluated with protein search software, and matrix proteins were identified. X-ray diffraction and infrared analysis confirmed that the stone contained calcium carbonate and calcium oxalate dihydrate. Of the identified 53 proteins, 24 have not been previously reported from calcium oxalate- or calcium phosphate-containing stones. The protease inhibitors and several proteins related to cell adhesion or the cytoskeleton were identified for the first time. We analyzed in detail a rare urinary stone composed of calcium carbonate and calcium oxalate dihydrate. Considering the formation of a calcium carbonate stone, the new identified proteins should play an important role on the urolithiasis process in alkaline condition. © 2013 The Japanese Urological Association.

Effect of experimental and sample factors on dehydration kinetics of mildronate dihydrate: mechanism of dehydration and determination of kinetic parameters.

PubMed

Bērziņš, Agris; Actiņš, Andris

2014-06-01

The dehydration kinetics of mildronate dihydrate [3-(1,1,1-trimethylhydrazin-1-ium-2-yl)propionate dihydrate] was analyzed in isothermal and nonisothermal modes. The particle size, sample preparation and storage, sample weight, nitrogen flow rate, relative humidity, and sample history were varied in order to evaluate the effect of these factors and to more accurately interpret the data obtained from such analysis. It was determined that comparable kinetic parameters can be obtained in both isothermal and nonisothermal mode. However, dehydration activation energy values obtained in nonisothermal mode showed variation with conversion degree because of different rate-limiting step energy at higher temperature. Moreover, carrying out experiments in this mode required consideration of additional experimental complications. Our study of the different sample and experimental factor effect revealed information about changes of the dehydration rate-limiting step energy, variable contribution from different rate limiting steps, as well as clarified the dehydration mechanism. Procedures for convenient and fast determination of dehydration kinetic parameters were offered. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Characterization of the calcification of cardiac valve bioprostheses by environmental scanning electron microscopy and vibrational spectroscopy.

PubMed

Delogne, Christophe; Lawford, Patricia V; Habesch, Steven M; Carolan, Vikki A

2007-10-01

Bioprosthetic heart valve tissue and associated calcification were studied in their natural state, using environmental scanning electron microscopy (ESEM). Energy dispersive X-ray micro-analysis, X-ray diffraction, Fourier-transform infrared and Raman spectroscopy were used to characterize the various calcific deposits observed with ESEM. The major elements present in calcified valves were also analyzed by inductively coupled plasma-optical emission spectroscopy. To better understand the precursor formation of the calcific deposits, results from the elemental analyses were statistically correlated. ESEM revealed the presence of four broad types of calcium phosphate crystal morphology. In addition, two main patterns of organization of calcific deposits were observed associated with the collagen fibres. Energy dispersive X-ray micro-analysis identified the crystals observed by ESEM as salts containing mainly calcium and phosphate with ratios from 1.340 (possibly octacalcium phosphate, which has a Ca/P ratio of 1.336) to 2.045 (possibly hydroxyapatite with incorporation of carbonate and metal ion contaminants, such as silicon and magnesium, in the crystal lattice). Raman and fourier-transform infrared spectroscopy also identified the presence of carbonate and the analyses showed spectral features very similar to a crystalline hydroxyapatite spectrum, also refuting the presence of precursor phases such as beta-tricalcium phosphate, octacalcium phosphate and dicalcium phosphate dihydrate. The results of this study raised the possibility of the presence of precursor phases associated with the early stages of calcification.

Biological availability and in vitro dissolution of oxytetracycline dihydrate tablets

PubMed Central

Barber, H. E.; Calvey, T. N.; Muir, K.; Hart, A.

1974-01-01

1 The concentration of oxytetracycline in plasma was studied by microbiological assay after oral administration of four different preparations of oxytetracycline dihydrate tablets. 2 There were statistically significant differences in biological availability between the four preparations, as assessed by the peak plasma level, the area under the plasma concentration-time curve, or the cumulative fraction of the dose excreted in urine at 405 minutes. In contrast, differences between the subjects were not statistically significant. 3 The differences in biological availability were not predictably related to the in vitro dissolution of the tablets. PMID:22454918

The ammonia-water phase diagram and its implications for icy satellites

NASA Technical Reports Server (NTRS)

Johnson, M. L.; Nicol, M.

1986-01-01

A Holzapfel-type diamond anvil cell is used to determine the NH3 - H2O phase diagram in the region from 0 to 33 mole percent NH3, 240 to 370 K, and 0 to 5 GPa. The following phases were identified: liquid; water ices Ih, III, V, VI, VII, and VIII; ammonia monohydrate, NH3.H2O; and ammonia dihydrate NH3.2H2O. Ammonia dihydrate becomes prominent at moderate pressures (less than 1 GPa), with planetologically significant implications, including the possibility of layering in Titan's magma ocean.

The ammonia-water phase diagram and its implications for icy satellites

NASA Technical Reports Server (NTRS)

Johnson, Mary L.; Nicol, Malcolm

1987-01-01

A Holzapfel-type diamond anvil cell is used to determine the NH3 - H2O phase diagram in the region from 0 to 33 mole percent NH3, 240 to 370 K, and 0 to 5 GPa. The following phases were identified: liquid; water ices Ih, III, V, VI, VII, and VIII; ammonia monohydrate, NH3.H2O; and ammonia dihydrate NH3.2H2O. Ammonia dihydrate becomes prominent at moderate pressures (less than 1 GPa), with planetologically significant implications, including the possibility of layering in Titan's magma ocean.

User’s Manual for Strategic Satellite System Terminal Segment Life Cycle Cost Model. Volume 1

DTIC Science & Technology

1981-03-01

the depot pipeline, given by: NFD(I) = EFAIL (I,NS)*TNB(NS) NS *1 [LRU(I) + RTS(NHI(1))]*NRTS(I)*DRCT(LO(NS)) + NRTS(NHI(i))*(l - COND(I))*DADI where... EFAIL (I,NS)*TNB(NS)* [(LRU(I) + RTS(NHI(I)))*NRTS(I) NS + NRTS(NHI(I))*(l-COND(I))] *DMH(I)*DMF where DMH(I) = averaRP marnours to perform depot...XJC - RSCA(I) + 12*PIUP* EFAIL (I,NS)*TNB(NS)* NS {(LRUCI)+RTS(NHI(I)))* (CR(I)*BIIH(I)*BMF*BLR + CN(I)*(DMH(I)*DMF*DLR + 2*CPPD(LOCNS))*WT(I)) + CC

Synthesis, crystal structure and magnetic properties of diaquabis(2,6-diamino-7H-purin-1-ium-κN9)bis(4,4'-oxydibenzoato-κO)cobalt(II) dihydrate.

PubMed

Atria, Ana María; Parada, José; Moreno, Yanko; Suárez, Sebastián; Baggio, Ricardo; Peña, Octavio

2018-01-01

The title mononuclear Co II complex, [Co(C 5 H 7 N 6 ) 2 (C 14 H 8 O 5 ) 2 (H 2 O) 2 ]·2H 2 O, has been synthesized and its crystal structure determined by X-ray diffraction. The complex crystallizes in the triclinic space group P-1, with one formula unit per cell (Z = 1 and Z' = 1/2). It consists of a mononuclear unit with the Co II ion on an inversion centre coordinated by two 2,6-diamino-7H-purin-1-ium cations, two 4,4'-oxydibenzoate anions (in a nonbridging κO-monodentate coordination mode, which is less common for the anion in its Co II complexes) and two water molecules, defining an octahedral environment around the metal atom. There is a rich assortment of nonbonding interactions, among which a strong N + -H...O - bridge, with a short N...O distance of 2.5272 (18) Å, stands out, with the H atom ostensibly displaced away from its expected position at the donor side, towards the acceptor. The complex molecules assemble into a three-dimensional hydrogen-bonded network. A variable-temperature magnetic study between 2 and 300 K reveals an orbital contribution to the magnetic moment and a weak antiferromagnetic interaction between Co II centres as the temperature decreases. The model leads to the following values: A (crystal field strength) = 1.81, λ (spin-orbit coupling) = -59.9 cm -1 , g (Landé factor) = 2.58 and zJ (exchange coupling) = -0.5 cm -1 .

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gil, D.M.; Osiry, H.; Pomiro, F.

The hydrogen bond and π-π stacking are two non-covalent interactions able to support cooperative magnetic ordering between paramagnetic centers. This contribution reports the crystal structure and related magnetic properties for VO[Fe(CN){sub 5}NO]·2H{sub 2}O, which has a layered structure. This solid crystallizes with an orthorhombic unit cell, in the Pna2{sub 1} space group, with cell parameters a=14.1804(2), b=10.4935(1), c=7.1722(8) Å and four molecules per unit cell (Z=4). Its crystal structure was solved and refined from powder X-ray diffraction data. Neighboring layers remain linked through a network of hydrogen bonds involving a water molecule coordinated to the axial position for the Vmore » atom and the unbridged axial NO and CN ligands. An uncoordinated water molecule is found forming a triple bridge between these last two ligands and the coordinated water molecule. The magnetic measurements, recorded down to 2 K, shows a ferromagnetic interaction between V atoms located at neighboring layers, with a Curie-Weiss constant of 3.14 K. Such ferromagnetic behavior was interpreted as resulting from a superexchange interaction through the network of strong OH····O{sub H2O}, OH····N{sub CN}, and OH····O{sub NO} hydrogen bonds that connects neighboring layers. The interaction within the layer must be of antiferromagnetic nature and it was detected close to 2 K. - Graphical abstract: Coordination environment for the metals in vanadyl (II) nitroprusside dihydrate. Display Omitted - Highlights: • Crystal structure of vanadyl nitroprusside dehydrate. • Network of hydrogen bonds. • Magnetic interactions through a network of hydrogen bonds. • Layered transition metal nitroprussides.« less

Bioavailability and dissolution of different formulations of oxytetracycline preparations.

PubMed Central

Hart, A; Barber, H E; Calvey, T N

1975-01-01

1 The concentration of oxytetracycline in plasma was studied by microbiological assay after oral administration of five different preparations of the antibiotic. None of these preparations had been studied previously. 2 There was a statistically significant correlation between the time required for 50% dissolution at pH 2 and biological availability, as assessed by the peak plasma level or the area under the plasma concentration-time curve. 3 The mean bioavailability of oxytetracycline was greatest with preparations of the hydrochloride, and with film-coated tablets of the dihydrate. In contrast, sugar-coated tablets of oxytetracycline dihydrate were associated with poorer dissolution characteristics and reduced biological availability. PMID:10944

The International Standard for Oxytetracycline

PubMed Central

Humphrey, J. H.; Lightbown, J. W.; Mussett, M. V.; Perry, W. L. M.

1955-01-01

The first attempt to set up an international standard for oxytetracycline, using oxytetracycline hydrochloride, failed because of difficulties in obtaining a preparation whose moisture content was uniform after distribution into ampoules. A preparation of dihydrate of oxytetracycline base was obtained instead, and was compared in an international collaborative assay with a sample of oxytetracycline hydrochloride, which was the current working standard of Chas. Pfizer & Co., Inc., USA. The results of the collaborative assay showed that the potency of the dihydrate was uniform, and that it was a suitable preparation for use as the International Standard. Evidence was obtained, however, that the reference preparation at the time of examination was less potent than had been originally supposed, and that it was hydrated. The potency of the proposed international standard was recalculated after allowance for water in the reference preparation, and the resulting biological potency agreed well with that to be expected on the basis of the physicochemical properties of the preparation. It was agreed, therefore, that the recalculated values should be used, and the preparation of oxytetracycline base dihydrate used in the collaborative assay is established as the International Standard for Oxytetracycline with a potency of 900 International Units per mg. PMID:13284563

4,5,7,8,17-Penta-hydr-oxy-14,18-dimethyl-6-methyl-ene-3,10-dioxapenta-cyclo-[9.8.0.0.0.0]nona-dec-14-ene-9,16-dione methanol solvate dihydrate.

PubMed

Teh, Chin Hoe; Teoh, Siew Chin; Yeap, Chin Sing; Chan, Kit Lam; Fun, Hoong-Kun

2009-03-28

The title quassinoid compound, C(20)H(24)O(9)·CH(3)OH·2H(2)O, is a natural eurycomanone isolated from the roots of Eurycoma longifolia. The mol-ecules contain a fused five-ring system, with one tetra-hydro-furan ring adopting an envelope conformation, one tetra-hydro-pyran-2-one ring in a screw boat conformation, one cyclo-hexenone ring in a half-chair conformation and two cyclo-hexane rings in chair conformations. Intra-molecular C-H⋯O inter-actions generate S(5) ring motifs and an O-H⋯O inter-action generates an S(7) ring motif. In the crystal, mol-ecules are linked via inter-molecular O-H⋯O inter-actions along the b axis and further stacked along a axis. The absolute configuration of the title compound was inferred from previously solved structures of its analogues.

Synthesis of IGZO ink and study of ink-jet printed IGZO thin films with different Ga concentrations

NASA Astrophysics Data System (ADS)

Shen, Y. K.; Liu, Z.; Wang, X. L.; Ma, W. K.; Chen, Z. H.; Chen, T. P.; Zhang, H. Y.

2017-12-01

By dissolving gallium chloride (GaCl3), indium chloride (InCl3), zinc acetate dihydrate [Zn(OAc)2·2H2O] and monoethanolamine (MEA) into a solvent of 2-methoxyethanol, the IGZO ink was synthesized. Five types of IGZO ink were prepared with different molar ratios of In:Ga:Zn, which can be used for ink-jet printing process. The thermal behaviors of IGZO ink with different formulas were investigated and the ideal annealing temperature for film formation was found to be ∼450 °C. Based on the prepared ink, amorphous IGZO thin films were directly printed on the glass substrate with a FujiFilm Dimatix ink-jet printer, followed by a thermal annealing at 450 °C for 1 h. The surface morphology, crystal structure, optical transmittance, electron mobility and carrier concentration were characterized and investigated. The ink-jet printed amorphous IGZO thin films fabricated in this work can be used as switching medium in flexible resistive random access memory devices.

6-[(Dimethyl­amino)methyl­ene­amino]-1,3-dimethyl­pyrimidine-2,4(1H,3H)-dione dihydrate

PubMed Central

Das, Subrata; Saikia, Binoy K.; Sridhar, B.; Thakur, Ashim J.

2008-01-01

Uracil, the pyrimidine nucleobase, which combined with adenine forms one of the major motifs present in the biopolymer RNA, is also involved in the self-assembly of RNA. In the title compound, C9H14N4O2·2H2O, the asymmetric unit contains one dimethyl­amino­uracil group and two water mol­ecules. The plane of the N=C—NMe2 side chain is inclined at 27.6 (5)° to the plane of the uracil ring. Both water mol­ecules form O—H⋯O hydrogen bonds with the carbonyl O atoms of the uracil group. Additional water–water hydrogen-bond inter­actions are also observed in the crystal structure. The O—H⋯O hydrogen bonds lead to the formation of a two-dimensional hydrogen-bonded network cage consisting of two dimethyl­amino­uracil groups and six water mol­ecules. PMID:21201655

Structural and optical properties of Na-doped ZnO films

NASA Astrophysics Data System (ADS)

Akcan, D.; Gungor, A.; Arda, L.

2018-06-01

Zn1-xNaxO (x = 0.0-0.05) solutions have been synthesized by the sol-gel technique using Zinc acetate dihydrate and Sodium acetate which were dissolved into solvent and chelating agent. Na-doped ZnO nanoparticles were obtained from solutions to find phase and crystal structure. Na-doped ZnO films have been deposited onto glass substrate by using sol-gel dip coating system. The effects of dopant concentration on the structure, morphology, and optical properties of Na-doped ZnO thin films deposited on glass substrate are investigated. Characterization of Zn1-xNaxO nanoparticles and thin films are examined using differential thermal analysis (DTA)/thermogravimetric analysis (TGA), Scanning electron microscope (SEM) and X-Ray diffractometer (XRD). Optical properties of Zn1-xNaxO thin films were obtained by using PG Instruments UV-Vis-NIR spectrophotometer in 190-1100 nm range. The structure, morphology, and optical properties of thin films are presented.

Grazing incidence synchrotron X-ray diffraction of marbles consolidated with diammonium hydrogen phosphate treatments: non-destructive probing of buried minerals

NASA Astrophysics Data System (ADS)

Possenti, Elena; Colombo, Chiara; Conti, Claudia; Gigli, Lara; Merlini, Marco; Plaisier, Jasper Rikkert; Realini, Marco; Gatta, G. Diego

2018-05-01

Diammonium hydrogen phosphate (DAP)-based consolidating treatments react with carbonatic stones and form calcium phosphates phases, whose composition depends on the availability of free calcium ions. In this work, an innovative non-destructive approach based on grazing incidence X-ray diffraction (GIXRD) with synchrotron radiation (SR) is used to investigate DAP-treated Carrara marble specimens and to study the influence of the substrate composition on the crystallization of calcium phosphate phases. The outcomes indicate that the presence of compositional micro-heterogeneity of Carrara marble favours the formation of specific phases. Dicalcium phosphate dihydrate, a calcium phosphate with a low Ca/P molar ratio, is formed on carbonatic phases with a low Ca amount, such as dolomite grains and Mg-containing veins. Furthermore, this study highlights the potentialities of SR-GIXRD as a powerful non-destructive tool for the diagnostic of Cultural Heritage objects since it allows investigating the conservation history of stone materials and their interaction with the environment.

Comparison of the relative stability of pharmaceutical cocrystals consisting of paracetamol and dicarboxylic acids.

PubMed

Suzuki, Naoto; Kawahata, Masatoshi; Yamaguchi, Kentaro; Suzuki, Toyofumi; Tomono, Kazuo; Fukami, Toshiro

2018-04-01

The aim of this study is to evaluate the relative stability of pharmaceutical cocrystals consisting of paracetamol (APAP) and oxalic acid (OXA) or maleic acid (MLA). These observations of cocrystal stability under various conditions are useful coformer criteria when cocrystals are selected as the active pharmaceutical ingredient in drug development. The relative stability was determined from the preferentially formed cocrystals under various conditions. Cocrystal of APAP-OXA was more stable than that of APAP-MLA in a ternary cogrinding system and possessed thermodynamical stability. On the other hand, when grinding with moisture or maintaining at high temperatures and relative humidity conditions, APAP-MLA was more stable, and OXA converted to OXA dihydrate. In the slurry method, APAP-OXA was more stable in aprotic solvents because the APAP-OXA with low-solubility product precipitated. The relative stability order was affected by preparing conditions of presence of moisture. This order might attribute to the small difference of crystal structure in the extension of the hydrogen bond network.

Hyaline cartilage involvement in patients with gout and calcium pyrophosphate deposition disease. An ultrasound study.

PubMed

Filippucci, E; Riveros, M Gutierrez; Georgescu, D; Salaffi, F; Grassi, W

2009-02-01

The main aim of the present study was to determine the sensitivity, specificity and accuracy of ultrasonography (US) in detecting monosodium urate and calcium pyrophosphate dihydrate crystals deposits at knee cartilage level using clinical definite diagnosis as standard reference. A total of 32 patients with a diagnosis of gout and 48 patients with pyrophosphate arthropathy were included in the study. Fifty-two patients with rheumatoid arthritis (RA), psoriatic arthritis or osteoarthritis (OA) were recruited as disease controls. All diagnoses were made using an international clinical criterion. US examinations were performed by an experienced sonographer, blind to clinical and laboratory data. Hyaline cartilage was assessed to detect two US findings recently indicated as indicative of crystal deposits: hyperechoic enhancement of the superficial margin of the hyaline cartilage and hyperechoic spots within the cartilage layer not generating a posterior acoustic shadow. Hyperechoic enhancement of the chondrosynovial margin was found in at least one knee of 14 out of 32 (43.7%) patients with gout and in a single knee of only one patient affected by pyrophosphate arthropathy (specificity=99%). Intra-cartilaginous hyperechoic spots were detected in at least one knee of 33 out of 48 (68.7%) patients with pyrophosphate arthropathy and in two disease controls one with OA and the second with RA (specificity=97.6%). The results of the present study indicate that US may play a relevant role in distinguishing cartilage involvement in patients with crystal-related arthropathy. The selected US findings were found to be highly specific.

Characterization of pore and crystal structure of synthesized LiBOB with varying quality of raw materials as electrolyte for lithium-ion battery

NASA Astrophysics Data System (ADS)

Lestariningsih, Titik; Ratri, Christin Rina; Wigayati, Etty Marty; Sabrina, Qolby

2016-02-01

Characterization of pore structure and crystal structure of the LiB(C2O4)2H2O or LIBOB compound has been performed in this study. These recent years, research regarding LiBOB electrolyte salt have been performed using analytical-grade raw materials, therefore this research was aimed to synthesized LiBOB electrolyte salt using the cheaper and abundant technical-grade raw materials. Lithium hydroxide (LiOH), oxalic acid dihydrate (H2C2O4.2H2O), and boric acid (H3BO3) both in technical-grade and analytical-grade quality were used as raw materials for the synthesis of LiBOB. Crystal structure characterization results of synthesized LiBOB from both technical-grade and analytical-grade raw materials have shown the existence of LiBOB and LiBOB hydrate phase with orthorombic structure. These results were also confirmed by FT-IR analysis, which showed the functional groups of LiBOB compounds. SEM analysis results showed that synthesized LiBOB has spherical structure, while commercial LiBOB has cylindrical structure. Synthesized LiBOB has a similar pore size of commercial LiBOB, i.e. 19 nm (mesoporous material). Surface area of synthesized LiBOB from analytical-grade raw materials and technical-grade materials as well as commercial LIBOB were 88.556 m2/g, 41.524 m2/g, and 108.776 m2/g, respectively. EIS analysis results showed that synthesized LiBOB from technical-grade raw materials has lower conductivity than synthesized LiBOB from analytical-grade raw materials.

Determination of dosimetric and kinetic features of gamma irradiated solid calcium ascorbate dihydrate using ESR spectroscopy

NASA Astrophysics Data System (ADS)

Tuner, H.

2013-01-01

Effects of gamma radiation on solid calcium ascorbate dihydrate were studied using electron spin resonance (ESR) spectroscopy. Irradiated samples were found to present two specific ESR lines with shoulder at low and high magnetic field sides. Structural and kinetic features of the radicalic species responsible for experimental ESR spectrum were explored through the variations of the signal intensities with applied microwave power, variable temperature, high-temperature annealing and room temperature storage time studies. Dosimetric potential of the sample was also determined using spectrum area and measured signal intensity measurements. It was concluded that three radicals with different spectroscopic and kinetic features were produced upon gamma irradiation.

Solid-phase molecular recognition of cytosine based on proton-transfer reaction. Part II. supramolecular architecture in the cocrystals of cytosine and its 5-Fluoroderivative with 5-Nitrouracil

PubMed Central

2011-01-01

Background Cytosine is a biologically important compound owing to its natural occurrence as a component of nucleic acids. Cytosine plays a crucial role in DNA/RNA base pairing, through several hydrogen-bonding patterns, and controls the essential features of life as it is involved in genetic codon of 17 amino acids. The molecular recognition among cytosines, and the molecular heterosynthons of molecular salts fabricated through proton-transfer reactions, might be used to investigate the theoretical sites of cytosine-specific DNA-binding proteins and the design for molecular imprint. Results Reaction of cytosine (Cyt) and 5-fluorocytosine (5Fcyt) with 5-nitrouracil (Nit) in aqueous solution yielded two new products, which have been characterized by single-crystal X-ray diffraction. The products include a dihydrated molecular salt (CytNit) having both ionic and neutral hydrogen-bonded species, and a dihydrated cocrystal of neutral species (5FcytNit). In CytNit a protonated and an unprotonated cytosine form a triply hydrogen-bonded aggregate in a self-recognition ion-pair complex, and this dimer is then hydrogen bonded to one neutral and one anionic 5-nitrouracil molecule. In 5FcytNit the two neutral nucleobase derivatives are hydrogen bonded in pairs. In both structures conventional N-H...O, O-H...O, N-H+...N and N-H...N- intermolecular interactions are most significant in the structural assembly. Conclusion The supramolecular structure of the molecular adducts formed by cytosine and 5-fluorocytosine with 5-nitrouracil, CytNit and 5FcytNit, respectively, have been investigated in detail. CytNit and 5FcytNit exhibit widely differing hydrogen-bonding patterns, though both possess layered structures. The crystal structures of CytNit (Dpka = -0.7, molecular salt) and 5FcytNit (Dpka = -2.0, cocrystal) confirm that, at the present level of knowledge about the nature of proton-transfer process, there is not a strict correlation between the Dpka values and the proton transfer, in that the acid/base pka strength is not a definite guide to predict the location of H atoms in the solid state. Eventually, the absence in 5FcytNit of hydrogen bonds involving fluorine is in agreement with findings that covalently bound fluorine hardly ever acts as acceptor for available Brønsted acidic sites in the presence of competing heteroatom acceptors. PMID:21888640

Changes in the solid state of anhydrous and hydrated forms of sodium naproxen under different grinding and environmental conditions: Evidence of the formation of new hydrated forms.

PubMed

Censi, Roberta; Rascioni, Riccardo; Di Martino, Piera

2015-05-01

The aim of the present work was to investigate the solid state change of the anhydrous and hydrate solid forms of sodium naproxen under different grinding and environmental conditions. Grinding was carried out manually in a mortar under the following conditions: at room temperature under air atmosphere (Method A), in the presence of liquid nitrogen under air atmosphere (Method B), at room temperature under nitrogen atmosphere (Method C), and in the presence of liquid nitrogen under nitrogen atmosphere (Method D). Among the hydrates, the following forms were used: a dihydrate form (DSN) obtained by exposing the anhydrous form at 55% RH; a dihydrate form (CSN) obtained by crystallizing sodium naproxen from water; the tetrahydrate form (TSN) obtained by exposing the anhydrous form at 75% RH. The metastable monohydrate form (MSN), previously described in the literature, was not used because of its high physical instability. The chemical stability during grinding was firstly assessed and proven by HPLC. Modification of the particle size and shape, and changes in the solid state under different grinding methods were evaluated by scanning electron microscopy, and X-ray powder diffractometry and thermogravimetry, respectively. The study demonstrated the strong influence of starting form, grinding and environmental conditions on particle size, shape and solid state of recovered sodium naproxen forms. In particular, it was demonstrated that in the absence of liquid nitrogen (Methods A and C), either at air or at nitrogen atmosphere, the monohydrate form (MSN) was obtained from any hydrates, meaning that these grinding conditions favored the dehydration of superior hydrates. The grinding process carried out in the presence of liquid nitrogen (Method B) led to further hydration of the starting materials: new hydrate forms were identified as one pentahydrate form and one hexahydrate form. The hydration was caused by the condensation of the atmospheric water on sodium naproxen particles by liquid nitrogen and by the grinding forces that created a close contact between water and drug. The simultaneous disruption of the crystals, occurring during grinding, and their close contact with water molecules promoted the conversion in higher hydrates. Under the Method D, it was possible to highlight a certain tendency to hydration probably due to a rearrangement of water already present into the hydrates, but results were substantially different from Method B. Thus, summarizing, the different SN forms behave differently under different grinding and environmental conditions. Copyright © 2015 Elsevier B.V. All rights reserved.

Recrystallization and Water Absorption Properties of Vitrified Trehalose Near Room Temperature.

PubMed

Shirakashi, Ryo; Takano, Kiyoshi

2018-05-10

To provide the physicochemical properties of vitrified trehalose for predicting its recrystallization. Thin films of vitrified trehalose solutions were prepared at room temperature and exposed to various humid and temperature atmospheres. The in-situ amount of retained water in the vacuum-dried trehalose thin film during exposure was determined using its FTIR spectrum by quantifying the extremely infinitesimal amount of retained water in the trehalose solution. Recrystallization of the sample was also assessed by the FTIR spectrum of trehalose dihydrate. The effective water absorption coefficient, h meff , exponentially increased to the water activity of the trehalose sample, A w , at 25°C and 40°C at which the increasing rates are comparable. The surface energy of trehalose dihydrate, γ, was found to be lower than the value calculated from the reported equation, neglecting the effects of the activity of the solute and solvent water. The retained water in trehalose considerably increases its affinity for water vapor, and the change in this affinity with regard to the water activity is nearly independent of temperature. The dihydrate nucleation rate of trehalose-water system is maximal when trehalose weight ratio is ~0.8 at 25°C and is slightly higher (~0.85) at 40°C.

The theoretical and experimental study on dicalcium phosphate dehydrate loading with protocatechuic aldehyde.

PubMed

Guo, Yuehua; Qu, Shuxin; Lu, Xiong; Xie, Haodong; Zhang, Hongping; Weng, Jie

2010-07-01

The aim of this study is to investigate the interaction between dicalcium phosphate dihydrate (CaHPO(4) x 2H(2)O, DCPD) and Protocatechuic aldehyde (C(7)H(6)O(3), Pca), which is the water-soluble constituents of Chinese Medicine, Salvia Miltiorrhiza Bunge (SMB), by calculating the absorption energy through molecular dynamics simulation. Furthermore, the effects of functional groups of Pca and temperature on Pca adsorbed by DCPD are calculated respectively. DCPD/Pca and DCPD were analyzed by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TG). The simulation results showed that Pca mostly absorbed on the (0 2 0) surface of DCPD. The aldehyde group of Pca played a moren important role on the adsorption of Pca on DCPD than hydroxyl did, while temperature had no distinct effects on the adsorption. XRD results indicated that Pca induced the preferential growth of (0 2 0) crystal surface in DCPC/Pca whereas it had no influence on the crystal structure, the crystallinity and grain size of DCPD. FTIR and TG results showed that the characteristic peak of Pca was at 1295 cm(-1) and the content of Pca in DCPD was 16%, respectively. The present results show that molecular dynamics simulation is a very effective and complementary method to study the interaction between materials and medicine.

Heat Stress Nephropathy From Exercise-Induced Uric Acid Crystalluria: A Perspective on Mesoamerican Nephropathy.

PubMed

Roncal-Jimenez, Carlos; García-Trabanino, Ramón; Barregard, Lars; Lanaspa, Miguel A; Wesseling, Catharina; Harra, Tamara; Aragón, Aurora; Grases, Felix; Jarquin, Emmanuel R; González, Marvin A; Weiss, Ilana; Glaser, Jason; Sánchez-Lozada, Laura G; Johnson, Richard J

2016-01-01

Mesoamerican nephropathy (MeN), an epidemic in Central America, is a chronic kidney disease of unknown cause. In this article, we argue that MeN may be a uric acid disorder. Individuals at risk for developing the disease are primarily male workers exposed to heat stress and physical exertion that predisposes to recurrent water and volume depletion, often accompanied by urinary concentration and acidification. Uric acid is generated during heat stress, in part consequent to nucleotide release from muscles. We hypothesize that working in the sugarcane fields may result in cyclic uricosuria in which uric acid concentrations exceed solubility, leading to the formation of dihydrate urate crystals and local injury. Consistent with this hypothesis, we present pilot data documenting the common presence of urate crystals in the urine of sugarcane workers from El Salvador. High end-of-workday urinary uric acid concentrations were common in a pilot study, particularly if urine pH was corrected to 7. Hyperuricemia may induce glomerular hypertension, whereas the increased urinary uric acid may directly injure renal tubules. Thus, MeN may result from exercise and heat stress associated with dehydration-induced hyperuricemia and uricosuria. Increased hydration with water and salt, urinary alkalinization, reduction in sugary beverage intake, and inhibitors of uric acid synthesis should be tested for disease prevention. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Fourier transform infrared spectroscopy for analysis of kidney stones.

PubMed

Khan, Aysha Habib; Imran, Sheharbano; Talati, Jamsheer; Jafri, Lena

2018-01-01

To compare the results of a chemical method of kidney stone analysis with the results of Fourier transform infrared (FT-IR) spectroscopy. Kidney stones collected between June and October 2015 were simultaneously analyzed by chemical and FT-IR methods. Kidney stones (n=449) were collected from patients from 1 to 81 years old. Most stones were from adults, with only 11.5% from children (aged 3-16 years) and 1.5% from children aged <2 years. The male to female ratio was 4.6. In adults, the calcium oxalate stone type, calcium oxalate monohydrate (COM, n=224), was the most common crystal, followed by uric acid and calcium oxalate dihydrate (COD, n=83). In children, the most frequently occurring type was predominantly COD (n=21), followed by COM (n=11), ammonium urate (n=10), carbonate apatite (n=6), uric acid (n=4), and cystine (n=1). Core composition in 22 stones showed ammonium urate (n=2), COM (n=2), and carbonate apatite (n=1) in five stones, while uric acid crystals were detected (n=13) by FT-IR. While chemical analysis identified 3 stones as uric acid and the rest as calcium oxalate only. Agreement between the two methods was moderate, with a kappa statistic of 0.57 (95% confidence interval, 0.5-0.64). Disagreement was noted in the analysis of 77 stones. FT-IR analysis of kidney stones can overcome many limitations associated with chemical analysis.

Navigating the Waters of Unconventional Crystalline Hydrates

PubMed Central

2015-01-01

Elucidating the crystal structures, transformations, and thermodynamics of the two zwitterionic hydrates (Hy2 and HyA) of 3-(4-dibenzo[b,f][1,4]oxepin-11-yl-piperazin-1-yl)-2,2-dimethylpropanoic acid (DB7) rationalizes the complex interplay of temperature, water activity, and pH on the solid form stability and transformation pathways to three neutral anhydrate polymorphs (Forms I, II°, and III). HyA contains 1.29 to 1.95 molecules of water per DB7 zwitterion (DB7z). Removal of the essential water stabilizing HyA causes it to collapse to an amorphous phase, frequently concomitantly nucleating the stable anhydrate Forms I and II°. Hy2 is a stoichiometric dihydrate and the only known precursor to Form III, a high energy disordered anhydrate, with the level of disorder depending on the drying conditions. X-ray crystallography, solid state NMR, and H/D exchange experiments on highly crystalline phase pure samples obtained by exquisite control over crystallization, filtration, and drying conditions, along with computational modeling, provided a molecular level understanding of this system. The slow rates of many transformations and sensitivity of equilibria to exact conditions, arising from its varying static and dynamic disorder and water mobility in different phases, meant that characterizing DB7 hydration in terms of simplified hydrate classifications was inappropriate for developing this pharmaceutical. PMID:26075319

Value of tomosynthesis for lesion evaluation of small joints in osteoarthritic hands using the OARSI score.

PubMed

Martini, K; Becker, A S; Guggenberger, R; Andreisek, G; Frauenfelder, T

2016-07-01

To determine the diagnostic performance of tomosynthesis in depicting osteoarthritic lesions in comparison to conventional radiographs, with use of computed tomography (CT) as standard-of-reference. Imaging of 12 cadaveric hands was performed with tomosynthesis in dorso-palmar (dp) projection, conventional radiographs (dp) and multi-detector CT. Distal interphalangeal joint (DIP)II, DIPIII, proximal interphalangeal joint (PIP)II, PIPIII, first carpometacarpal (CMC) and scaphotrapezotrapezoidal joint (STT) were graded by two independent readers using the Osteoarthritis Research Society International (OARSI) score. The mean score for each feature was calculated for all modalities. Additional wrists were evaluated for presence of calcium pyrophosphate disease (CPPD). CT served as reference-standard. Inter-reader agreement (ICC) was calculated. Comparing tomosynthesis and conventional radiographs to CT, the sensitivity for the presence of osteophytes was 95,7% vs 65,2%; for joint space narrowing 95,8% vs 52,1%; for subchondral sclerosis 61,5% vs 51,3%; for lateral deformity 83.3% vs 83,3%; and for subchondral cysts 45,8% vs 29,2%. Erosions were not present. While tomosynthesis showed no significant difference in OARSI score grading to CT (mean OARSI-score CT: 16.8, SD = 10.6; mean OARSI-score Tomosynthesis: 16.3, SD = 9.6; P = 0.84), conventional radiographs had significant lower mean OARSI scores (mean OARSI-score X-ray: 11.1, SD = 8.3; P = 0.04). Inter-reader agreement for OARSI scoring was excellent (ICC = 0.99). CPPD calcifications present in CT, were also visible with tomosynthesis, but not with conventional radiography. In conclusion, tomosynthesis depicts more osteoarthritic changes in the small joints of the hand than conventional radiography using the OARSI scoring system and CT as the standard of reference. Copyright © 2016 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Toxicology and carcinogenesis studies of sodium dichromate dihydrate (Cas No. 7789-12-0) in F344/N rats and B6C3F1 mice (drinking water studies).

PubMed

2008-07-01

Sodium dichromate dihydrate is one of a number of inorganic compounds containing hexavalent chromium (Cr VI) found in drinking water source supplies as a contaminant resulting from various industrial processes including electroplating operations, leather tanning, and textile manufacturing. Because of the lack of adequate experimental data on the toxicity and carcinogenicity of hexavalent chromium ingested orally and because hexavalent chromium has been found in drinking water source supplies, the California Congressional Delegation, the California Environmental Protection Agency, and the California Department of Health Services nominated hexavalent chromium to the National Toxicology Program for study. Results of 3 month toxicity studies in F344/N rats and B6C3F1, BALB/c, and am3-C57BL/6 mice were reported earlier in NTP Toxicity Report 72. In the current study, male and female F344/N rats and B6C3F1 mice were exposed to sodium dichromate dihydrate (greater than 99.7% pure) in drinking water for 2 years. 2-YEAR STUDY IN RATS: Groups of 50 male and 50 female rats were exposed to drinking water containing 0, 14.3, 57.3, 172, or 516 mg/L sodium dichromate dihydrate (equivalent to 0, 5, 20, 60, or 180 mg/L chromium) for 2 years (equivalent to average daily doses of approximately 0.6, 2.2, 6, or 17 mg sodium dichromate dihydrate/kg body weight for males and 0.7, 2.7, 7, or 20 mg/kg for females). Survival of exposed groups was similar to that of the control groups. Mean body weights of 516 mg/L males and females were less than those of the controls throughout the study. The lower body weights were partly attributed to poor palatability of the dosed water and consequent reductions in water consumption. Water consumption by 172 and 516 mg/L rats was less than that by the controls throughout the study. Exposure to sodium dichromate dihydrate caused a microcytic hypochromic anemia in rats that ameliorated with time. Exposure to sodium dichromate dihydrate resulted in the development of neoplasms of the squamous epithelium that lines the oral mucosa and tongue. The incidences of squamous cell carcinoma in the oral mucosa of 516 mg/L male and female rats were significantly greater than those in the controls. The incidence in 172 mg/L females exceeded the historical control ranges for drinking water studies and for all routes of administration. The incidences of squamous cell papilloma or squamous cell carcinoma (combined) of the oral mucosa or tongue of 516 mg/L male and female rats were significantly greater than those in the controls. Exposure concentration-related nonneoplastic liver lesions were observed in males and females exposed to 57.3 mg/L or greater. These included histiocytic cellular infiltration, chronic inflammation, fatty change (females), basophilic focus (males), and clear cell focus (females). Increased incidences of histiocytic cellular infiltration also occurred in the small intestine (duodenum), mesenteric lymph node, and pancreatic lymph node of males and/or females exposed to 57.3 mg/L or greater. 2-YEAR STUDY IN MICE: Groups of 50 male mice were exposed to drinking water containing 0, 14.3, 28.6, 85.7, or 257.4 mg/L sodium dichromate dihydrate (equivalent to 0, 5, 10, 30, or 90 mg/L chromium) for 2 years (equivalent to average daily doses of approximately 1.1, 2.6, 7, or 17 mg sodium dichromate dihydrate/kg body weight). Groups of 50 female mice were exposed to drinking water containing 0, 14.3, 57.3, 172, or 516 mg/L sodium dichromate dihydrate (equivalent to 0, 5, 20, 60, or 180 mg/L chromium) for 2 years (equivalent to average daily doses of approximately 1.1, 3.9, 9, or 25 mg/kg). Survival of exposed groups was similar to that of the control groups. Mean body weights of 257.4 mg/L males were less than those of controls from months 2 through 6 of the study, but by the end of the study, the mean body weight of 257.4 mg/L males was only slightly less than that of the control group. Mean body weights of 172 mg/L females were less than those of the controls from months 3 through 12 of the study, and mean body weights of 516 mg/L females were less than those of the controls from month 2 until the end of the study. By the end of the study, the mean body weight of 172 mg/L females was 8% less than that of the controls, and the mean body weight of 516 mg/L females was 15% less than that of the controls. The lower body weights were partly attributed to poor palatability of the dosed water and consequent reductions in water consumption. Water consumption by 85.7 and 257.4 mg/L males and 172 and 516 mg/L females was less than that by the controls throughout the study. A treatment-related microcytosis occurred in exposed mice; the mice were less affected than the rats. The incidences of neoplasms of the small intestine (duodenum, jejunum, or ileum) were increased in exposed groups of male and female mice. The incidences of adenoma of the duodenum in 257.4 mg/L males and 172 and 516 mg/L females were significantly greater than those in the controls. The incidence of carcinoma of the duodenum was significantly increased in 516 mg/L females. The incidence of adenoma of the jejunum in 516 mg/L females was significantly increased compared to that in the controls. When the incidences of adenoma and carcinoma were combined for all sites of the small intestine, the incidences were significantly increased in 85.7 and 257.4 mg/L males and 172 and 516 mg/L females compared to those in the controls. The incidences in 57.3 mg/L females exceeded the historical control ranges for drinking water studies and for all routes of administration. The incidences of diffuse epithelial hyperplasia were significantly increased in the duodenum of all exposed groups of male and female mice. The incidences of histiocytic cellular infiltration were significantly increased in the duodenum of 85.7 and 257.4 mg/L males and in 172 and 516 mg/L females. In the jejunum, the incidences of diffuse epithelial hyperplasia and histiocytic cellular infiltration were significantly increased in 516 mg/L females. The incidences of histiocytic cellular infiltration of the liver in all exposed groups of females, of the mesenteric lymph node in all exposed groups of males and females, and of the pancreatic lymph node of 85.7 and 257.4 mg/L males and 172 and 516 mg/L females were significantly increased. Tissue distribution studies showed that total chromium concentrations tended to increase with increasing exposure concentration and duration of exposure. Under the conditions of these 2-year drinking water studies, there was clear evidence of carcinogenic activity of sodium dichromate dihydrate in male and female F344/N rats based on increased incidences of squamous cell neoplasms of the oral cavity. There was clear evidence of carcinogenic activity of sodium dichromate dihydrate in male and female B6C3F1 mice based on increased incidences of neoplasms of the small intestine (duodenum, jejunum, or ileum). Exposure to sodium dichromate dihydrate resulted in histiocytic cellular infiltration in the liver, small intestine, and pancreatic and mesenteric lymph nodes of rats and mice and diffuse epithelial hyperplasia in the small intestine of male and female mice.

Electrical conductivity and total dissolved solids in urine.

PubMed

Fazil Marickar, Y M

2010-08-01

The objective of this paper is to study the relevance of electrical conductivity (EC) and total dissolved solids (TDS) in early morning and random samples of urine of urinary stone patients; 2,000 urine samples were studied. The two parameters were correlated with the extent of various urinary concrements. The early morning urine (EMU) and random samples of the patients who attended the urinary stone clinic were analysed routinely. The pH, specific gravity, EC, TDS, redox potential, albumin, sugar and microscopic study of the urinary sediments including red blood cells (RBC), pus cells (PC), crystals, namely calcium oxalate monohydrate (COM), calcium oxalate dihydrate (COD), uric acid (UA), and phosphates and epithelial cells were assessed. The extent of RBC, PC, COM, COD, UA and phosphates was correlated with EC and TDS. The values of EC ranged from 1.1 to 33.9 mS, the mean value being 21.5 mS. TDS ranged from 3,028 to 18,480 ppm, the mean value being 7,012 ppm. The TDS levels corresponded with EC of urine. Both values were significantly higher (P < 0.05) in the EMU samples than the random samples. There was a statistically significant correlation between the level of abnormality in the urinary deposits (r = +0.27, P < 0.05). In samples, where the TDS were more than 12,000 ppm, there were more crystals than those samples containing TDS less than 12,000 ppm. However, there were certain urine samples, where the TDS were over 12,000, which did not contain any urinary crystals. It is concluded that the value of TDS has relevance in the process of stone formation.

Cooperation of phosphates and carboxylates controls calcium oxalate crystallization in ultrafiltered urine.

PubMed

Grohe, Bernd; Chan, Brian P H; Sørensen, Esben S; Lajoie, Gilles; Goldberg, Harvey A; Hunter, Graeme K

2011-10-01

Osteopontin (OPN) is one of a group of proteins found in urine that are believed to limit the formation of kidney stones. In the present study, we investigate the roles of phosphate and carboxylate groups in the OPN-mediated modulation of calcium oxalate (CaOx), the principal mineral phase found in kidney stones. To this end, crystallization was induced by addition of CaOx solution to ultrafiltered human urine containing either human kidney OPN (kOPN; 7 consecutive carboxylates, 8 phosphates) or synthesized peptides corresponding to residues 65-80 (pSHDHMDDDDDDDDDGD; pOPAR) or 220-235 (pSHEpSTEQSDAIDpSAEK; P3) of rat bone OPN. Sequence 65-80 was also synthesized without the phosphate group (OPAR). Effects on calcium oxalate monohydrate (COM) and dihydrate (COD) formation were studied by scanning electron microscopy. We found that controls form large, partly intergrown COM platelets; COD was never observed. Adding any of the polyelectrolytes was sufficient to prevent intergrowth of COM platelets entirely, inhibiting formation of these platelets strongly, and inducing formation of the COD phase. Strongest effects on COM formation were found for pOPAR and OPAR followed by kOPN and then P3, showing that acidity and hydrophilicity are crucial in polyelectrolyte-affected COM crystallization. At higher concentrations, OPAR also inhibited COD formation, while P3, kOPN and, in particular, pOPAR promoted COD, a difference explainable by the variations of carboxylate and phosphate groups present in the molecules. Thus, we conclude that carboxylate groups play a primary role in inhibiting COM formation, but phosphate and carboxylate groups are both important in initiating and promoting COD formation.

77 FR 8863 - Product Cancellation Order for Certain Pesticide Registrations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-15

...-00001 X-100 Natural Seal Wood 2-(Thiocyanomethylthio) benzothiazole, Preservative. Methylene bis... dichloroisocyanurate dihydrate. Disinfectant Cleanser. 075015-00001 Dead-Fast Insecticide Chalk Tralomethrin. 080697...

Elaboration, structural, spectroscopy, DSC investigations and Hirshfeld surface analysis of a one-dimensional self-assembled organic-inorganic hybrid compound

NASA Astrophysics Data System (ADS)

Mesbeh, Radhia; Hamdi, Besma; Zouari, Ridha

2017-01-01

The new organic-inorganic hybrid of the formula [H2mela]Cu2Cl6, where mela = 1,3,5-triazine-2,4,6-triamine, has been synthesized by the reaction of 1,3,5-triazine-2,4,6-triamine and copper(II) chloride dihydrate in the presence of hydrochloric acid. This compound has been determined by X-ray diffraction analysis and characterized by FT-IR, Raman, NMR characterization, differential scanning calorimetric (DSC) analysis, dielectric measurements and Hirshfeld surface. 1,3,5-triazinidium-2,4,6-triamine hexachlorodicuprate(II) crystallizes in the monoclinic system with space group P21/c. The final refinement of the structure of the program led to the reliability factors unweighted R1 = 3.53% and weighted WR2 = 8.87%. The observed internal C3sbnd N31sbnd C1 and C3sbnd N23sbnd C2 angle (121.5 and 121.4°) at protanated N-atom are significantly greater the other ring angle C1sbnd N12sbnd C2 (117.1°). The titled compound crystallizes as an organic-inorganic one-dimensional (1D) structure. The crystal structure was stabilized by two types of hydrogen bonding Nsbnd H⋯Cl and Nsbnd H⋯N. The infrared spectra was recorded in the 4000-400 cm-1 frequency region and the Raman spectra was recorded in the external region of the anionic sublattice vibration 4000-50 cm-1 at room temperature. Solid-state 13C and 63Cu MAS-NMR spectroscopies are in agreement with the X-ray structure. The differential scanning calorimetric (DSC) show the presence of a structural phase transition of the title compound at 338 K. Hirshfeld surface analyses for visually analyzing intermolecular interactions in crystal structures employing molecular surface contours and 2D fingerprint plots have been used to examine molecular shapes.

Evolution of post-ESWL residual lithiasis depending on the type of calculus and urine composition.

PubMed

Grases, Felix; Costa-Bauzá, Antonia; Isern, Bernat; Sanchis, Pilar; Perelló, Joan; Hierro, Fernando; Conte Visus, Antonio

2009-07-01

Extracorporeal shock wave lithotripsy (ESWL) is one of the most commonly used procedures for removal of renal calculi from the upper urinary tract, but complete expulsion of the fragments generated is not always achieved. This can lead to new lithiasic episodes, and it is considered that 10-26% of fragmented calculi can undergo regrowth. This in vitro study investigated the influence of fragment and urinary composition on post-ESWL growth of fragments, with the aims of establishing the effect and importance of these parameters, and identifying effective prophylactic measures. Fragments collected from patients immediately following expulsion after ESWL treatment were selected for regrowth experiments. The particles included 24 calcium oxalate monohydrate (COM) fragments, 48 calcium oxalate dihydrate (COD), 24 hydroxyapatite (HAP), and 16 uric acid. In all treatments, calculi fragments showed a considerable capacity to induce growth of calcium oxalate and calcium phosphate. Under normocalciuria conditions, new COM crystals formed; both COM and COD crystals developed under hypercalciuria conditions at a urinary pH < 6.0; and in hypercalciuric conditions and urinary pH > 6.0 both HAP and brushite (BRU) crystals were formed. The highest growth rates were observed for COD calculi fragments under hypercalciuria conditions and at a urinary pH of 6.5, followed by growth on COM and HAP fragments under the same conditions; growth rates under other conditions tested were similar but 10-fold lower. With regard to the role of crystallization inhibitors, phytate exhibited inhibitory effects under all assay conditions. However, citrate had little effect, even at the highest concentration tested (1,000 mg/L). This study demonstrates the importance of avoiding heterogeneous nucleant retention (pre-existing solid microparticles) in renal cavities, as these can act as very efficient inducers of the formation of new calculi, the composition of which is mainly dependant on the urine composition.

Unusual effect of water vapor pressure on dehydration of dibasic calcium phosphate dihydrate.

PubMed

Kaushal, Aditya M; Vangala, Venu R; Suryanarayanan, Raj

2011-04-01

Dibasic calcium phosphate occurs as an anhydrate (DCPA; CaHPO₄) and as a dihydrate (DCPD; CaHPO₄•2H₂O). Our objective was to investigate the unusual behavior of these phases. Dibasic calcium phosphate dihydrate was dehydrated in a (i) differential scanning calorimeter (DSC) in different pan configurations; (ii) variable-temperature X-ray diffractometer (XRD) at atmospheric and under reduced pressure, and in sealed capillaries; and (iii) water vapor sorption analyzer at varying temperature and humidity conditions. Dehydration was complete by 210°C in an open DSC pan and under atmospheric pressure in the XRD. Unlike "conventional" hydrates, the dehydration of DCPD was facilitated in the presence of water vapor. Variable-temperature XRD in a sealed capillary and DSC in a hermetic pan with pinhole caused complete dehydration by 100°C and 140°C, respectively. Under reduced pressure, conversion to the anhydrate was incomplete even at 300°C. The increase in dehydration rate with increase in water vapor pressure has been explained by the Smith-Topley effect. Under "dry" conditions, a coating of poorly crystalline product is believed to form on the surface of particles and act as a barrier to further dehydration. However, in the presence of water vapor, recrystallization occurs, creating cracks and channels and facilitating continued dehydration. Copyright © 2010 Wiley-Liss, Inc.

Pharmacokinetics and Bioequivalence Evaluation of 2 Loxoprofen Tablets in Healthy Egyptian Male Volunteers.

PubMed

Helmy, Sally A

2013-04-01

The objective of this study was to assess the in vitro dissolution and to evaluate the bioavailability of two brands of Loxoprofen sodium dihydrate tablets. Loxoprofen tablets (68.1 mg loxoprofen sodium dihydrate equivalent to 60 mg loxoprofen; test) relative to Roxonin tablets (68.1 mg loxoprofen sodium dihydrate equivalent to 60 mg loxoprofen; reference). In vitro study was adopted to determine and compare the dissolution behavior of both products. In vivo study was conducted according to a single-center, randomized, single-dose, and laboratory-blinded, 2-period, 2-sequence, crossover design with a washout period of 1 week. Under fasting conditions, 24 healthy Egyptian adult male volunteers were randomly allocated to receive a single dose of either test or reference product. Blood samples were collected at specified time intervals, and plasma was analyzed for loxoprofen concentrations using a validated high-performance liquid chromatography assay method. The pharmacokinetic parameters Cmax , AUC0-t , AUC0-∞ , tmax , and t1/2 were determined from plasma concentration-time profiles. The 90% confidence intervals for the ratio Cmax , AUC0-t , and AUCt-∞ of the test product over those of reference were within the acceptable range (0.8-1.25) for bioequivalence. On the basis of these results, the two-loxoprofen formulations are considered bioequivalent. © The Author(s) 2013.

Phase Transformations in a Human Tooth Tissue at the Initial Stage of Caries

PubMed Central

Prutskij, Tatiana; Ippolitov, Yury

2015-01-01

The aim of the paper is to study phase transformations in solid tissues of the human teeth during the development of fissure caries by Raman and fluorescence microspectroscopy. The study of the areas with fissure caries confirmed the assumption of the formation of a weak interaction between phosphate apatite enamel and organic acids (products of microorganisms). The experimental results obtained with by Raman microspectroscopy showed the formation of dicalcium phosphate dihydrate - CaHPO4-2H2O in the area of mural demineralization of carious fissure. A comparative analysis of structural and spectroscopic data for the intact and carious enamel shows that emergence of a more soluble phase - carbonate-substituted hydroxyapatite - is typical for the initial stage of caries. It is shown that microareas of dental hard tissues in the carious fissure due to an emerging misorientation of apatite crystals have a higher fluorescence yield than the area of the intact enamel. These areas can be easily detected even prior to a deep demineralization (white spot stage) for the case of irreversibly changed organomineral complex and intensive removal of the mineral component. PMID:25901743

A detailed study of intermolecular interactions, electronic and vibrational properties of the metal complex bis(uracilato)diammine copper(ii) dihydrate

NASA Astrophysics Data System (ADS)

Gramajo Feijoo, M.; Fernández-Liencres, M. P.; Gil, D. M.; Gómez, M. I.; Ben Altabef, A.; Navarro, A.; Tuttolomondo, M. E.

2018-03-01

Density Functional Theory (DFT) calculations were performed with the aim of investigating the vibrational, electronic and structural properties of [Cu(uracilato-N1)2 (NH3)2]ṡ2H2O complex. The IR and Raman spectra were recorded leading to a complete analysis of the normal modes of vibration of the metal complex. A careful study of the intermolecular interactions observed in solid state was performed by using the Hirshfeld surface analysis and their associated 2D fingerprint plots. The results indicated that the crystal packing is stabilized by Nsbnd H⋯O hydrogen bonds and π-stacking interactions. In addition, Csbnd H···π interactions were also observed. Time-dependent density functional theory (TD-DFT) calculations revealed that all the low-lying electronic states correspond to a mixture of intraligand charge transfer (ILCT) and ligand-to-metal charge transfer (LMCT) transitions. Finally, Natural Bond Orbital (NBO) and Atoms in Molecules (AIM) analysis were performed to shed light on the intermolecular interactions in the coordination sphere.

Ammonia clathrate hydrates as new solid phases for Titan, Enceladus, and other planetary systems.

PubMed

Shin, Kyuchul; Kumar, Rajnish; Udachin, Konstantin A; Alavi, Saman; Ripmeester, John A

2012-09-11

There is interest in the role of ammonia on Saturn's moons Titan and Enceladus as the presence of water, methane, and ammonia under temperature and pressure conditions of the surface and interior make these moons rich environments for the study of phases formed by these materials. Ammonia is known to form solid hemi-, mono-, and dihydrate crystal phases under conditions consistent with the surface of Titan and Enceladus, but has also been assigned a role as water-ice antifreeze and methane hydrate inhibitor which is thought to contribute to the outgassing of methane clathrate hydrates into these moons' atmospheres. Here we show, through direct synthesis from solution and vapor deposition experiments under conditions consistent with extraterrestrial planetary atmospheres, that ammonia forms clathrate hydrates and participates synergistically in clathrate hydrate formation in the presence of methane gas at low temperatures. The binary structure II tetrahydrofuran + ammonia, structure I ammonia, and binary structure I ammonia + methane clathrate hydrate phases synthesized have been characterized by X-ray diffraction, molecular dynamics simulation, and Raman spectroscopy methods.

Ammonia clathrate hydrates as new solid phases for Titan, Enceladus, and other planetary systems

PubMed Central

Shin, Kyuchul; Kumar, Rajnish; Udachin, Konstantin A.; Alavi, Saman; Ripmeester, John A.

2012-01-01

There is interest in the role of ammonia on Saturn’s moons Titan and Enceladus as the presence of water, methane, and ammonia under temperature and pressure conditions of the surface and interior make these moons rich environments for the study of phases formed by these materials. Ammonia is known to form solid hemi-, mono-, and dihydrate crystal phases under conditions consistent with the surface of Titan and Enceladus, but has also been assigned a role as water-ice antifreeze and methane hydrate inhibitor which is thought to contribute to the outgassing of methane clathrate hydrates into these moons’ atmospheres. Here we show, through direct synthesis from solution and vapor deposition experiments under conditions consistent with extraterrestrial planetary atmospheres, that ammonia forms clathrate hydrates and participates synergistically in clathrate hydrate formation in the presence of methane gas at low temperatures. The binary structure II tetrahydrofuran + ammonia, structure I ammonia, and binary structure I ammonia + methane clathrate hydrate phases synthesized have been characterized by X-ray diffraction, molecular dynamics simulation, and Raman spectroscopy methods. PMID:22908239

Performance of the 2015 American College of Rheumatology/European League Against Rheumatism gout classification criteria in Thai patients.

PubMed

Louthrenoo, Worawit; Jatuworapruk, Kanon; Lhakum, Panomkorn; Pattamapaspong, Nuttaya

2017-05-01

To evaluate the sensitivity and specificity of the 2015 American College of Rheumatology/European League Against Rheumatism (ACR/EULAR) gout classification criteria in Thai patients presenting with acute arthritis in a real-life setting. Data were analyzed on consecutive patients presenting with arthritis of less than 2 weeks duration. Sensitivity and specificity were calculated by using the presence of monosodium urate (MSU) crystals in the synovial fluid or tissue aspirate as gold standard for gout diagnosis. Subgroup analysis was performed in patients with early disease (≤2 years), established disease (>2 years), and those without tophus. Additional analysis also was performed in non-tophaceous gout patients, and patients with acute calcium pyrophosphate dihydrate crystal arthritis were used as controls. One hundred and nine gout and 74 non-gout patients participated in this study. Full ACR/EULAR classification criteria had sensitivity and specificity of 90.2 and 90.0%, respectively; and 90.2 and 85.0%, respectively, when synovial fluid microscopy was excluded. Clinical-only criteria yielded sensitivity and specificity of 79.8 and 87.8%, respectively. The criteria performed well among patients with early and non-tophaceous disease, but had lower specificity in patients with established disease. The variation of serum uric acid level was a major limitation of the classification criteria. The ACR/EULAR classification criteria had high sensitivity and specificity in Thai patients presenting with acute arthritis, even when clinical criteria alone were used.

Protein-Mediated Precipitation of Calcium Carbonate

PubMed Central

Polowczyk, Izabela; Bastrzyk, Anna; Fiedot, Marta

2016-01-01

Calcium carbonate is an important component in exoskeletons of many organisms. The synthesis of calcium carbonate was performed by mixing dimethyl carbonate and an aqueous solution of calcium chloride dihydrate. The precipitation product was characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR) measurements. In addition, the turbidity of the reaction solution was acquired to monitor the kinetics of the calcium carbonate structure’s growth in the investigated system. In this study, samples of CaCO3 particles obtained with individual proteins, such as ovalbumin, lysozyme, and a mixture of the proteins, were characterized and compared with a control sample, i.e., synthesized without proteins. The obtained data indicated that the addition of ovalbumin to the reaction changed the morphology of crystals from rhombohedral to ‘stack-like’ structures. Lysozyme, however, did not affect the morphology of calcium carbonate, yet the presence of the protein mixture led to the creation of more complex composites in which the calcium carbonate crystals were constructed in protein matrices formed by the ovalbumin-lysozyme interaction. It was also observed that in the protein mixture, ovalbumin has a major influence on the CaCO3 formation through a strong interaction with calcium ions, which leads to the coalescence and creation of a steric barrier reducing particle growth. The authors proposed a mechanism of calcium carbonate grain growth in the presence of both proteins, taking into account the interaction of calcium ions with the protein. PMID:28774065

Crystal structure of tetra-aqua-bis(3,5-di-amino-4H-1,2,4-triazol-1-ium)cobalt(II) bis-[bis-(pyridine-2,6-di-carboxyl-ato)cobaltate(II)] dihydrate.

PubMed

Johnson, Atim; Mbonu, Justina; Hussain, Zahid; Loh, Wan-Sin; Fun, Hoong-Kun

2015-06-01

The asymmetric unit of the title compound, [Co(C2H6N5)2(H2O)4][Co(C7H3NO4)2]2·2H2O, features 1.5 Co(II) ions (one anionic complex and one half cationic complex) and one water mol-ecule. In the cationic complex, the Co(II) atom is located on an inversion centre and is coordinated by two triazolium cations and four water mol-ecules, adopting an octa-hedral geometry where the N atoms of the two triazolium cations occupy the axial positions and the O atoms of the four water mol-ecules the equatorial positions. The two triazole ligands are parallel offset (with a distance of 1.38 Å between their planes). In the anionic complex, the Co(II) ion is six-coordinated by two N and four O atoms of the two pyridine-2,6-di-carboxyl-ate anions, exhibiting a slightly distorted octa-hedral coordination geometry in which the mean plane of the two pyridine-2,6-di-carboxyl-ate anions are almost perpendicular to each other, making a dihedral angle of 85.87 (2)°. In the crystal, mol-ecules are linked into a three-dimensional network via C-H⋯O, C-H⋯N, O-H⋯O and N-H⋯O hydrogen bonds.

Evaluation of a biphasic in vitro dissolution test for estimating the bioavailability of carbamazepine polymorphic forms.

PubMed

Deng, Jia; Staufenbiel, Sven; Bodmeier, Roland

2017-07-15

The purpose of this study was to discriminate three crystal forms of carbamazepine (a BCS II drug) by in vitro dissolution testing and to correlate in vitro data with published in vivo data. A biphasic dissolution system (phosphate buffer pH6.8 and octanol) was used to evaluate the dissolution of the three polymorphic forms and to compare it with conventional single phase dissolution tests performed under sink and non-sink conditions. Similar dissolution profiles of three polymorphic forms were observed in the conventional dissolution test under sink conditions. Although a difference in dissolution was seen in the single phase dissolution test under non-sink conditions as well as in the aqueous phase of the biphasic test, little relevance for in vivo data was observed. In contrast, the biphasic dissolution system could discriminate between the different polymorphic forms in the octanol phase with a ranking of form III>form I>dihydrate form. This was in agreement with the in vivo performance. The dissolved drug available for oral absorption, which was dominated by dissolution and solution-mediated phase transformation, could be reflected in the biphasic dissolution test. Moreover, a good correlation was established between in vitro dissolution in the octanol phase of the biphasic test and in vivo pharmacokinetic data (R 2 =0.99). The biphasic dissolution method is a valuable tool to discriminate between different crystal forms in the formulations of poorly soluble drugs. Copyright © 2017. Published by Elsevier B.V.

Influence of shot peening on corrosion properties of biocompatible magnesium alloy AZ31 coated by dicalcium phosphate dihydrate (DCPD).

PubMed

Mhaede, Mansour; Pastorek, Filip; Hadzima, Branislav

2014-06-01

Magnesium alloys are promising materials for biomedical applications because of many outstanding properties like biodegradation, bioactivity and their specific density and Young's modulus are closer to bone than the commonly used metallic implant materials. Unfortunately their fatigue properties and low corrosion resistance negatively influenced their application possibilities in the field of biomedicine. These problems could be diminished through appropriate surface treatments. This study evaluates the influence of a surface pre-treatment by shot peening and shot peening+coating on the corrosion properties of magnesium alloy AZ31. The dicalcium phosphate dihydrate coating (DCPD) was electrochemically deposited in a solution containing 0.1M Ca(NO3)2, 0.06M NH4H2PO4 and 10mL/L of H2O2. The effect of shot peening on the surface properties of magnesium alloy was evaluated by microhardness and surface roughness measurements. The influence of the shot peening and dicalcium phosphate dihydrate layer on the electrochemical characteristics of AZ31 magnesium alloy was evaluated by potentiodynamic measurements and electrochemical impedance spectroscopy in 0.9% NaCl solution at a temperature of 22±1°C. The obtained results were analyzed by the Tafel-extrapolation method and equivalent circuit method. The results showed that the application of shot peening process followed by DCPD coating improves the properties of the AZ31 surface from corrosion and mechanical point of view. Copyright © 2014 Elsevier B.V. All rights reserved.

Hydrogen bonding Part 53. Correlation of differential scanning calorimetric data with IR and dissociation vapor pressure studies of transitions of hexamethonium chloride and bromide dihydrates and hexamethonium bromide monohydrate

NASA Astrophysics Data System (ADS)

Snider, Barbara L.; Harmon, Kenneth M.

1994-03-01

Differential scanning calorimetry of hexamethonium chloride dihydrate shows an endothermic transition of 2.70 kcal mol -1 at 36.81°C. This correlates well with the temperatures observed by IR spectra (36°C) and equilibrium dissociation vapor pressure studies (37°C) for the transition between Type I planar cluster and Type II extended linear HOH⋯Cl - hydrogen bonding, and with the value of 2.77 kcal mol -1 for this transition derived by Hess' law treatment of dissociation vapor pressure data. Differential scanning calorimetry of hexamethonium bromide shows a rapid endothermic transition of 2.38 kcal mol -1 at 35.15°C and a very slow endothermic transition of about 12-13 kcal mol -1 centered near 50°C. This latter endotherm corresponds to the transition between Type I and Type II HOH⋯Br - hydrogen bonding observed by IR and vapor pressure studies at 49°C. The nature of the 35.15°C endotherm is not known. Hexamethonium bromide also shows a third endotherm at 142.91°C, which presumably results from melting of hydrate in the sealed DSC cell. Combined analysis of differential scanning calorimetry and dissociation vapor pressure data predicts a value of about -13 kcal mol -1 for an exothermic disproportionation at 52°C of two hexamethonium bromide monohydrate to Type II dihydrate and anhydrous bromide.

Gas adsorption on commercial magnesium stearate: Effects of degassing conditions on nitrogen BET surface area and isotherm characteristics.

PubMed

Lapham, Darren P; Lapham, Julie L

2017-09-15

Commercial grades of magnesium stearate have been analysed by nitrogen adsorption having been pre-treated at temperatures between 30°C and 110°C and in the as-received state. Characteristics of nitrogen adsorption/desorption isotherms are assessed through the linearity of low relative pressure isotherm data and the BET transform plot together with the extent of isotherm hysteresis. Comparison is made between thermal gravimetric analysis and mass loss on drying. Features of gas adsorption isotherms considered atypical are identified and possible causes presented. It is shown that atypical isotherm features and issues of applying BET theory to the calculation of S BET are linked to the presence of hydrated water and that these depend on the hydration state: being more pronounced for the di-hydrate than the mono-hydrate. Dehydration reduces the extent of atypical features. S BET of a mono-hydrate sample is 5.6m 2 g -1 and 3.2m 2 g -1 at 40°C and 100°C degassing respectively but 23.9m 2 g 1 and 5.9m 2 g -1 for di-hydrate containing samples under comparable degassing. Di-hydrated samples also show S BET >15m 2 g 1 , BET C-values <7 and BET correlation coefficients <0.98 before dehydration. Possible mechanisms for atypical isotherms are critically discussed together with the suitability of applying BET theory to nitrogen adsorption data. Copyright © 2017 Elsevier B.V. All rights reserved.

The ammonia-water system and the chemical differentiation of icy satellites

USGS Publications Warehouse

Hogenboom, D.L.; Kargel, J.S.; Consolmagno, G.J.; Holden, T.C.; Lee, L.; Buyyounouski, M.

1997-01-01

We report the discovery of the first high-pressure polymorphs of ammonia hydrates: ammonia monohydrate II and ammonia dihydrate II. The subsolidus transitions and melting curves of these substances are shown by their volume-temperature functions; uncalibrated calorimetry corroborates these phase changes. From 20 to 300 MPa ammonia dihydrate and ice melt at a eutectic to form water-rich liquids; at lower and higher pressures, ammonia dihydrate melts incongruently to ammonia-rich liquids. The new data are consistent with independently known thermodynamic parameters of the ammonia-water system. These results fill in an important region of pressure-temperature space not previously studied; a body of previous data reported by other investigators covers a complementary region (higher pressures), but in the light of the new data those earlier results now appear to have been misinterpreted. We show that a suitable reinterpretation of the previous data supports the identification of at least one high-pressure polymorph of each compound. The behavior of the system H2O-NH3in many ways follows that of MgO-SiO2, and the roles of ammonia-water in icy satellite evolution may parallel those of magnesium silicates in Earth's structure, volcanism, and deep mantle tectonism. Pressure-related effects, including a pressure influence on the ammonia content of cryomagmas, might be significant in determining some potentially observable aspects of cryovolcanic morphologies, surface compositions, and interior structures of icy satellites. ?? 1997 Academic Press.

Solid state stability and solubility of triethylenetetramine dihydrochloride.

PubMed

Henriet, Théo; Gana, Inès; Ghaddar, Carine; Barrio, Maria; Cartigny, Yohann; Yagoubi, Najet; Do, Bernard; Tamarit, Josep-Lluis; Rietveld, Ivo B

2016-09-10

The API triethylenetetramine dihydrochloride used as an alternative treatment of Wilson's disease is sensitive to water and it exhibits polymorphism. As this may become an issue for the drug formulation, the physical stability has been studied by differential scanning calorimetry, high-pressure thermal analysis, dynamic vapor sorption, and X-ray diffraction as a function of temperature. In addition, high-pressure liquid chromatography and mass spectrometry have been used to study the purity and chemical stability of the API. A pressure-temperature phase diagram of the pure compound has been constructed and it can be concluded that form II is monotropic in relation to form I, which is the only stable solid. The solubilities of the different solid forms have been determined with the help of a temperature - composition phase diagram. The API is very soluble, at 20° C about 10% of the saturated solution with respect to the dihydrate consists of API and the solubility of the pure form I is twice as high. Moreover, it has been shown that at 20°C, a relative humidity above 40% induces the formation of the dihydrate and at 70% a saturated solution appears. At higher temperatures, the formation of the dihydrate appears at lower relative humidity values. A clear link has been established between the API's chemical stability, its physical stability and the relative humidity in the air. Humidity levels above 40% are detrimental to the quality of the API. Copyright © 2016 Elsevier B.V. All rights reserved.

Precipitation diagrams and solubility of uric acid dihydrate

NASA Astrophysics Data System (ADS)

Babić-Ivančić, V.; Füredi-Milhofer, H.; Brown, W. E.; Gregory, T. M.

1987-07-01

The solubility of uric acid dihydrate (UA·2H 2O) and the precipitation of UA·2H 2O and anhydrous uric acid (UA) from solutions containing sodium hydroxide and hydrochloric acid have been investigated. For the solubility studies, crystals of pure UA·2H 2O were prepared and equilibrated with water and with solutions of HCl or NaOH for 60 min or 20 h, respectively. The equilibrium pH (pH = 2-6.25) and uric acid concentration were determined. For the precipitation experiments, commercial UA was dissolved in NaOH in a 1:1.1 molar ratio and UA·2H 2O and/or UA were precipitated with hydrochloric acid. The precipitates and/or supernatants were examined 24 h after sample preparation. The results are represented in the form of tables, precipitation diagrams and "chemical potential" diagrams. Solubility measurements with 60 min equilibration times yielded the solubility products of UA·2H 2O, K sp(298 K) = (0.926 ± 0.025) × 10 -9mol2dm-6 and K sp(310 K) = (2.25 ± 0.05) × 10 -9mol2dm-6 and the first dissociation constants of uric acid, K 1(298 K) = (2.45 ± 0.07) × 10 -6moldm-3 and K 1(310 K) = (3.63 ± 0.08) × 10 -6moldm-3. Precipitation diagrams show that under the given experimental conditions, at 298 K, UA·2H 2O is stable for 24 h while at 310 K this was true only for precipitates formed from solutions of high supersaturations. At lower supersaturations, mixtures of UA·2H 2O and UA formed. Consequently, while the Ksp value determined from precipitation data obtained at 298 K (K sp = 1.04 × 10 -9mol2dm-6) was consistent with the respective solubility product, the 310 K precipitation boundary yielded an ion activity product, AP, the value of which fulfills the conditions Ksp(UA) < AP < Ksp (UA·2H 2O). Similar ion activity products were obtained from solubility measurements in pure water at 20 h equilibration time.

Chemical composition and binary mixture of human urinary stones using FT-Raman spectroscopy method.

PubMed

Selvaraju, R; Raja, A; Thiruppathi, G

2013-10-01

In the present study the human urinary stones were observed in their different chemical compositions of calcium oxalate monohydrate, calcium oxalate dihydrate, calcium phosphate, struvite (magnesium ammonium phosphate), uric acid, cystine, oxammite (ammonium oxalate monohydrate), natroxalate (sodium oxalate), glushinkite (magnesium oxalate dihydrate) and moolooite (copper oxalate) were analyzed using Fourier Transform-Raman (FT-Raman) spectroscopy. For the quantitative analysis, various human urinary stone samples are used for ratios calculation of binary mixtures compositions such as COM/COD, HAP/COD, HAP/COD, Uric acid/COM, uric acid/COD and uric acid/HAP. The calibration curve is used for further analysis of binary mixture of human urinary stones. For the binary mixture calculation the various intensities bands at 1462 cm(-1) (I(COM)), 1473 cm(-1) (I(COD)), 961 cm(-1) (I(HAP)) and 1282 cm(-1) (I(UA)) were used. Copyright © 2013 Elsevier B.V. All rights reserved.

The Burn Rate of Calcium Sulfate Dihydrate-Aluminum Thermites.

PubMed

Govender, Desania Raquel; Focke, Walter Wilhelm; Tichapondwa, Shepherd Masimba; Cloete, William Edward

2018-05-29

The energetics of cast calcium sulfate dihydrate-aluminium thermites was investigated. The casts were prepared form water slurries with a solids content of xxx wt-%. The base case thermite comprised 60 wt-% calcium sulfate dihydrate as the oxidiser with 40 wt-% aluminium as fuel. The heat of hydration of the base case was 59 ± 8 kJkg-1 and the setting time was zzz min. The compressive strength reached 2.9 ± 0.2 MPa after three days drying in ambient air. The open air burn rate was 12.0 ± 1.6 mm s-1 and a maximum surface temperature of 1370 ± 64 °C was recorded with a pyrometer. Bomb calorimetry indicated an energy output of 8.0 ± 1.1 MJ kg-1, slightly lower than predicted by the EKVI thermodynamic simulation. Substitution of 10 wt-% of the oxidant with copper sulfate pentahydrate significantly decreased the setting time of the casts to about yyy min. The density of the castings was varied by either adding hollow sodium borosilicate glass spheres or by adding excess water during the casting process. The addition of the hollow glass spheres caused a decrease in the burning rate. The burning rate of the base case was not affected materially by the addition of excess water. However, it did increase the burning rate of the copper sulfate pentahydrate-modified thermite. Dehydration of the casts by thermal treatments at either 155 °C or 200 °C also led to significant increases in the burning rate.

21 CFR 573.360 - Disodium EDTA.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES PERMITTED IN FEED AND DRINKING WATER OF ANIMALS Food Additive Listing § 573.360 Disodium EDTA. The food additive disodium EDTA (disodium ethylenediaminetetraace- tate... food additive contains a minimum of 99 percent disodium ethylenediaminetetraacetate dihydrate...

21 CFR 573.360 - Disodium EDTA.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES PERMITTED IN FEED AND DRINKING WATER OF ANIMALS Food Additive Listing § 573.360 Disodium EDTA. The food additive disodium EDTA (disodium ethylenediaminetetraace- tate... food additive contains a minimum of 99 percent disodium ethylenediaminetetraacetate dihydrate...

21 CFR 573.360 - Disodium EDTA.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES PERMITTED IN FEED AND DRINKING WATER OF ANIMALS Food Additive Listing § 573.360 Disodium EDTA. The food additive disodium EDTA (disodium ethylenediaminetetraace- tate... food additive contains a minimum of 99 percent disodium ethylenediaminetetraacetate dihydrate...

21 CFR 573.360 - Disodium EDTA.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES PERMITTED IN FEED AND DRINKING WATER OF ANIMALS Food Additive Listing § 573.360 Disodium EDTA. The food additive disodium EDTA (disodium ethylenediaminetetraace- tate... food additive contains a minimum of 99 percent disodium ethylenediaminetetraacetate dihydrate...

21 CFR 573.360 - Disodium EDTA.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES PERMITTED IN FEED AND DRINKING WATER OF ANIMALS Food Additive Listing § 573.360 Disodium EDTA. The food additive disodium EDTA (disodium ethylenediaminetetraace- tate... food additive contains a minimum of 99 percent disodium ethylenediaminetetraacetate dihydrate...

4,5,7,8,17-Penta­hydr­oxy-14,18-dimethyl-6-methyl­ene-3,10-dioxapenta­cyclo­[9.8.0.01,7.04,19.013,18]nona­dec-14-ene-9,16-dione methanol solvate dihydrate

PubMed Central

Teh, Chin Hoe; Teoh, Siew Chin; Yeap, Chin Sing; Chan, Kit Lam; Fun, Hoong-Kun

2009-01-01

The title quassinoid compound, C20H24O9·CH3OH·2H2O, is a natural eurycomanone isolated from the roots of Eurycoma longifolia. The mol­ecules contain a fused five-ring system, with one tetra­hydro­furan ring adopting an envelope conformation, one tetra­hydro­pyran-2-one ring in a screw boat conformation, one cyclo­hexenone ring in a half-chair conformation and two cyclo­hexane rings in chair conformations. Intra­molecular C—H⋯O inter­actions generate S(5) ring motifs and an O—H⋯O inter­action generates an S(7) ring motif. In the crystal, mol­ecules are linked via inter­molecular O—H⋯O inter­actions along the b axis and further stacked along a axis. The absolute configuration of the title compound was inferred from previously solved structures of its analogues. PMID:21582604

Nitromethane Bridged Bis(1,3,4-oxadiazoles): Trianionic Energetic Salts with Low Sensitivities.

PubMed

Yu, Qiong; Imler, Gregory H; Parrish, Damon A; Shreeve, Jean'ne M

2017-12-14

Trianionic energetic salts based on one nitromethylene and two dinitromethyl anions were designed and synthesized. Interestingly, the unstable dinitromethylene group of diethyl 2,2'-((dinitromethylene)bis(1,3,4-oxadiazole-5,2-diyl))bis(2,2-dinitroacetate) (2) was changed to a mononitromethylene group by an aminolysis reaction to form triammonium ((nitromethanidylene)bis(1,3,4-oxadiazole-5,2-diyl))bis(dinitromethanide) (3), whereas in (dinitrobis(5-(trinitromethyl)-1,3,4-oxadiazol-2-yl)methan) 8 it was hydrolyzed to a carbonyl group resulting in (bis(5-(trinitromethyl)-1,3,4-oxadiazol-2-yl)methanone) 9. All the new compounds were fully characterized by infrared, multinuclear NMR spectra, and elemental analysis. The structures of triammonium ((nitromethanidylene)bis(1,3,4-oxadiazole-5,2-diyl))bis(dinitromethanide) dihydrate (3⋅2 H 2 O) and bis(2-dinitromethyl-1,3,4-oxadiazole-5-yl)methanone (9) were further confirmed by single-crystal X-ray diffraction analysis. Based on their different physical and detonation properties, some of the energetic salts were found to exhibit good energetic performance and low sensitivity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Bis[1-meth­oxy-2,2,2-tris­(pyrazol-1-yl-κN 2)ethane]­nickel(II) bis­(tri­fluoro­methane­sulfonate) dihydrate

PubMed Central

Lyubartseva, Ganna; Parkin, Sean; Mallik, Uma Prasad

2013-01-01

In the title salt, [Ni(C12H14N6O)2](CF3SO3)2·2H2O, the NiII cation is located on an inversion centre and is coordinated by six N atoms from two tridentate 1-meth­oxy-2,2,2-tris­(pyrazol-1-yl)ethane ligands in a distorted octa­hedral geometry. The Ni—N distances range from 2.0594 (12) to 2.0664 (12) Å, intra-ligand N—Ni—N angles range from 84.59 (5) to 86.06 (5)°, and adjacent inter-ligand N—Ni—N angles range between 93.94 (5) and 95.41 (5)°. In the crystal, inversion-related pyrazole rings are π–π stacked, with an inter­planar spacing of 3.4494 (18) Å, forming chains that propagate parallel to the a-axis direction. Inter­molecular O—H⋯O hydrogen bonds are present between water mol­ecules and tri­fluoro­methane­sulfonate anions. PMID:24098167

Charcot-like joints in calcium pyrophosphate dihydrate deposition disease

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helms, C.A.; Chapman, G.S.; Wild, J.H.

1981-10-01

Two cases of Charcot-like joints in patients with pseudogout who were otherwise neurologically intact are presented. The arthropathy of pseudogout should include Charcot-like joints and it is emphasized that an apparent Charcot joint should raise the question of pseudogout.

Breast Microcalcification Detection Using Super-Resolution Ultrasound Image Reconstruction

DTIC Science & Technology

2010-09-01

microcalcifications often occur as one of two types: calcium oxalate dihydrate or calcium hydroxyapatite. Their sizes range approximately from 0.1 mm to 0.5 mm...super-resolution imaging, ultrasound imaging, wave equation. 1. INTRODUCTION Microcalcifications, tiny specks of mineral deposits ( calcium ), are the

Provisional Peer-Reviewed Toxicity Values for Sodium Tungstate Dihydrate

EPA Science Inventory

Provisional Peer-Reviewed Toxicity Values (PPRTV) assessments are developed for use by the Agency’s Office of Land and Emergency Management (OLEM) to support informed decisions in the Superfund program and at hazardous waste sites when a values is not available in the Integrated ...

Alcohol vapor sensing by cadmium-doped zinc oxide thick films based chemical sensor

NASA Astrophysics Data System (ADS)

Zargar, R. A.; Arora, M.; Chackrabarti, S.; Ahmad, S.; Kumar, J.; Hafiz, A. K.

2016-04-01

Cadmium-doped zinc oxide nanoparticles were derived by simple chemical co-precipitation route using zinc acetate dihydrate and cadmium acetate dihydrate as precursor materials. The thick films were casted from chemical co-precipitation route prepared nanoparticles by economic facile screen printing method. The structural, morphological, optical and electrical properties of the film were characterized relevant to alcohol vapor sensing application by powder XRD, SEM, UV-VIS and DC conductivity techniques. The response and sensitivity of alcohol (ethanol) vapor sensor are obtained from the recovery curves at optimum working temperature range from 20∘C to 50∘C. The result shows that maximum sensitivity of the sensor is observed at 25∘C operating temperature. On varying alcohol vapor concentration, minor variation in resistance has been observed. The sensing mechanism of sensor has been described in terms of physical adsorption and chemical absorption of alcohol vapors on cadmium-doped zinc oxide film surface and inside film lattice network through weak hydrogen bonding, respectively.

Influence of addition of calcium sulfate dihydrate on drying of autoclaved aerated concrete

NASA Astrophysics Data System (ADS)

Małaszkiewicz, Dorota; Chojnowski, Jacek

2017-11-01

The quality of the autoclaved aerated concrete (AAC) strongly depends on the chemical composition of the raw materials, as well as on the process of the hydrothermal reaction during autoclaving. Performance parameters depend on material structure: fine micron-scale matrix porosity generated by the packing of thin tobermorite plates and coarse aeration pores arising from the foaming of wet mix. In this study the binder varied in calcium sulfate dihydrate (CaSO4ṡ2H2O) content. Five series of AAC specimens were produced, with gypsum content 0; 0.55; 1.15; 2.3 and 3.5% of dry mass respectively. AAC units were produced in UNIPOL technology. The study presents experimental results of AAC moisture stabilization. The initial moisture content was determined directly after autoclaving. Slower drying process was observed for samples containing over 2% of gypsum. Whereas other performance parameters, compressive and tensile strength, as well as water absorption and capillary rise, were significantly better comparing to the reference AAC samples.

Cloud forming potential of oligomers relevant to secondary organic aerosols

NASA Astrophysics Data System (ADS)

Xu, Wen; Guo, Song; Gomez-Hernandez, Mario; Zamora, Misti L.; Secrest, Jeremiah; Marrero-Ortiz, Wilmarie; Zhang, Annie L.; Collins, Don R.; Zhang, Renyi

2014-09-01

The hygroscopic growth factor (HGF) and cloud condensation nuclei (CCN) activity are measured for surrogates that mimic atmospherically relevant oligomers, including glyoxal trimer dihydrate, methyl glyoxal trimer dihydrate, sucrose, methyl glyoxal mixtures with sulfuric acid and glycolic acid, and 2,4-hexandienal mixtures with sulfuric acid and glycolic acid. For the single-component aerosols, the measured HGF ranges from 1.3 to 1.4 at a relative humidity of 90%, and the hygroscopicity parameter (κ) is in the range of 0.06 to 0.19 on the basis of the measured CCN activity and 0.13 to 0.22 on the basis of the measured HGF, compared to the calculated values of 0.08 to 0.16. Large differences exist in the κ values derived using the measured HGF and CCN data for the multi-component aerosols. Our results reveal that, in contrast to the oxidation process, oligomerization decreases particle hygroscopicity and CCN activity and provides guidance for analyzing the organic species in ambient aerosols.

The acoustic velocity, refractive index, and equation of state of liquid ammonia dihydrate under high pressure and high temperature.

PubMed

Ma, Chunli; Wu, Xiaoxin; Huang, Fengxian; Zhou, Qiang; Li, Fangfei; Cui, Qiliang

2012-09-14

High-pressure and high-temperature Brillouin scattering studies have been performed on liquid of composition corresponding to the ammonia dihydrate stoichiometry (NH(3)·2H(2)O) in a diamond anvil cell. Using the measured Brillouin frequency shifts from 180° back- and 60° platelet-scattering geometries, the acoustic velocity, refractive index, density, and adiabatic bulk modulus have been determined under pressure up to freezing point along the 296, 338, 376, and 407 K isotherms. Along these four isotherms, the acoustic velocities increase smoothly with increasing pressure but decrease with the increased temperature. However, the pressure dependence of the refractive indexes on the four isotherms exhibits a change in slope around 1.5 GPa. The bulk modulus increases linearly with pressure and its slope, dB/dP, decreases from 6.83 at 296 K to 4.41 at 407 K. These new datasets improve our understanding of the pressure- and temperature-induced molecular structure changes in the ammonia-water binary system.

Syntheses, structures and characterization of isomorphous CoII and NiII coordination polymers based on 2-[(1H-imidazol-1-yl)methyl]-6-methyl-1H-benzimidazole and benzene-1,4-dicarboxylate.

PubMed

Huang, Qiu Ying; Zhao, Yang; Meng, Xiang Ru

2017-08-01

Careful choice of the organic ligands is one of the most important parameters in the rational design and synthesis of coordination polymers. Aromatic polycarboxylates have been widely used in the preparation of metal-organic polymers since they can utilize various coordination modes to form diverse structures and can act as hydrogen-bond acceptors and donors in the assembly of supramolecular structures. Nitrogen-heterocyclic organic compounds have also been used extensively as ligands for the construction of polymers with interesting structures. In the polymers catena-poly[[[diaquabis{2-[(1H-imidazol-1-yl)methyl]-6-methyl-1H-benzimidazole-κN 3 }cobalt(II)]-μ 2 -benzene-1,4-dicarboxylato-κ 2 O 1 :O 4 ] dihydrate], {[Co(C 8 H 4 O 4 )(C 12 H 11 N 4 ) 2 (H 2 O) 2 ]·2H 2 O} n , (I), and catena-poly[[[diaquabis{2-[(1H-imidazol-1-yl)methyl]-6-methyl-1H-benzimidazole-κN 3 }nickel(II)]-μ 2 -benzene-1,4-dicarboxylato-κ 2 O 1 :O 4 ] dihydrate], {[Ni(C 8 H 4 O 4 )(C 12 H 11 N 4 ) 2 (H 2 O) 2 ]·2H 2 O} n , (II), the Co II or Ni II ion lies on an inversion centre and exhibits a slightly distorted octahedral coordination geometry, coordinated by two N atoms from two imidazole rings and four O atoms from two monodentate carboxylate groups and two water molecules. The dicarboxylate ligands bridge metal ions forming a polymeric chain. The 2-[(1H-imidazol-1-yl)methyl]-6-methyl-1H-benzimidazole ligands coordinate to the Co II or Ni II centres in monodentate modes through an imidazole N atom and are pendant on opposite sides of the main chain. The two structures are isomorphous. In the crystal, the one-dimensional chains are further connected through O-H...O, O-H...N and N-H...O hydrogen bonds, leading to a three-dimensional supramolecular architecture. In addition, the IR spectroscopic properties, PXRD patterns, thermogravimetric behaviours and fluorescence properties of both polymers have been investigated.

Experimental and Theoretical Electron Density Distribution of Alpha,Alpha-Trehalose Dihydrate

USDA-ARS?s Scientific Manuscript database

Alpha,alpha-rehalose is of interest because of its cryoprotective and antidessicant properties, and because it possesses various technical anomalies such as 13C NMR spectra that give misleading indications of intramolecular structural symmetry. It is a non-reducing disaccharide, with the glycosidic...

Provisional Peer-Reviewed Toxicity Values for Trialuminum Sodium Tetra Decahydrogenoctaorthophosphate (dihydrate)

EPA Science Inventory

Provisional Peer-Reviewed Toxicity Values (PPRTV) assessments are developed for use by the Agency’s Office of Land and Emergency Management (OLEM) to support informed decisions in the Superfund program and at hazardous waste sites when a values is not available in the Integrated ...

Differential diagnostic perspectives provided by en face microscopic examination of articular surface defects.

PubMed

Rothschild, Bruce M

2018-03-01

Surface defects have a central position in diagnosis of articular pathology. Recognizing the limitations of standard radiologic techniques and those imposed by positioning and averaging artifacts on CT evaluation, direct visualization of surface defects was pursued to identify disease characteristics that would facilitate interpretation of radiologic findings. Epi-illumination surface microscopy was utilized to examine macroscopically recognized articular surface defects in individuals in the Hamann-Todd, Terry, and Huntington human skeletal collections with previously verified diagnoses of rheumatoid arthritis, spondyloarthropathy, juvenile inflammatory arthritis (JIA), calcium pyrophosphate deposition disease (CPPD), gout, metastatic cancer, multiple myeloma, septic arthritis, tuberculosis, fungal arthritis, histiocytosis and sickle cell anemia (Rothschild and Rothschild Clin Infect Dis 20(5):1402-1408, 1995; Rothschild et al. Amer J Phys Anthropol 82(4):441-449, 1990; Rothschild and Rothschild Amer J Phys Anthropol 96(4):357-563, 1995; Rothschild and Woods Clin Exp Rheumatol 10(2):117-122, 1992; Barrett and Keat Radiographics 24(6):1679-1691, 2004; Rothschild and Heathcote Amer J Phys Anthropol 98(4):519-525, 1995; Rothschild and Woods Am J Phys Anthropol 85:25-34, 1991; Hershkovitz et al. Amer J Phys Anthropol 106(1):47-60, 1998; Winland et al. Amer J Phys Anthropol 24:S243, 1997; Rothschild et al. Clin Exp Rheumatol 10(6):557-564, 1992; Rothschild and Martin , 2006; Rothschild et al. Amer J Phys Anthropol 102(2):249-264, 1997). Observed alterations were compared with standard radiographs. Fronts of resorption distinguished inflammatory arthritis from those caused by the other disorders studied. Multiple myeloma, fungal disease, and gout are expansile character; the latter accompanied by reactive new bone formation more prominent than that noted with spondyloarthropathy and JIA. Those were clearly distinguished from the crumbling alterations found with CPPD. Histiocytosis had a unique crenulated appearance, while nodules were prominent with syphilis. Defects in sickle cell anemia had ivory fragments at their base. These findings provided explanation for radiologic observations. Direct surface microscopy revealed characteristics apparently pathognomonic for specific disorders and facilitated distinguishing among them. The technique provides visualization an order of magnitude greater than that available with clinical radiologic techniques and identifies new characteristics which should facilitate clinical diagnoses. This demonstrates that there would be value to the development of higher resolution, clinically applicable imaging techniques.

Thermodynamic properties of selenoether-functionalized ionic liquids and their use for the synthesis of zinc selenide nanoparticles.

PubMed

Klauke, Karsten; Zaitsau, Dzmitry H; Bülow, Mark; He, Li; Klopotowski, Maximilian; Knedel, Tim-Oliver; Barthel, Juri; Held, Christoph; Verevkin, Sergey P; Janiak, Christoph

2018-04-03

Three selenoether-functionalized ionic liquids (ILs) of N-[(phenylseleno)methylene]pyridinium (1), N-(methyl)- (2) and N-(butyl)-N'-[(phenylseleno)methylene]imidazolium (3) with bis(trifluoromethanesulfonyl)imide anions ([NTf2]) were prepared from pyridine, N-methylimidazole and N-butylimidazole with in situ obtained phenylselenomethyl chloride, followed by ion exchange to give the desired compounds. The crystal structures of the bromide and tetraphenylborate salts of the above cations (1-Br, 2-BPh4 and 3-BPh4) confirm the formation of the desired cations and indicate a multitude of different supramolecular interactions besides the dominating Coulomb interactions between the cations and anions. The vaporization enthalpies of the synthesized [NTf2]-containing ILs were determined by means of a quartz-crystal microbalance method (QCM) and their densities were measured with an oscillating U-tube. These thermodynamic data have been used to develop a method for assessment of miscibility of conventional solvents in the selenium-containing ILs by using Hildebrandt solubility parameters, as well as for modeling with the electrolyte perturbed-chain statistical associating fluid theory (ePC-SAFT) method. Furthermore, structure-property relations between selenoether-functionalized and similarly shaped corresponding aryl-substituted imidazolium- and pyridinium-based ILs were analyzed and showed that the contribution of the selenium moiety to the enthalpy of vaporization of an IL is equal to the contribution of a methylene (CH2) group. An incremental approach to predict vaporization enthalpies of ILs by a group contribution method has been developed. The reaction of these ILs with zinc acetate dihydrate under microwave irradiation led to ZnSe nanoparticles of an average diameter between 4 and 10 nm, depending on the reaction conditions.

Use of absorption mechanisms to decrease heavy metal mobility.

DOT National Transportation Integrated Search

2014-02-01

The objective of this project is to reduce the toxic heavy metal leaching from coal fly ash so that the fly ash may be used for road : surface or related applications. Trona (trisodium hydrogendicarbonate dihydrate, Na3HCO3CO32H2O) is injected into...

Computer modelling of solid alkali metal carboxylates

NASA Astrophysics Data System (ADS)

Barreto, L. S.; Mort, K. A.; Jackson, R. A.; Alves, O. L.

2000-11-01

A computational study of solid lithium acetate dihydrate and anhydrous sodium acetate is presented. Interatomic potentials are obtained by empirical fitting to experimental structural data for both materials and the resulting potentials were found to be transferable to different phases of the same materials, giving good agreement with the experimental structure.

Nitranilic acid hexahydrate, a novel benchmark system of the Zundel cation in an intrinsically asymmetric environment: spectroscopic features and hydrogen bond dynamics characterised by experimental and theoretical methods.

PubMed

Molčanov, Krešimir; Stare, Jernej; Vener, Mikhail V; Kojić-Prodić, Biserka; Mali, Gregor; Grdadolnik, Jože; Mohaček-Grošev, Vlasta

2014-01-21

Nitranilic acid (2,5-dihydroxy-3,6-dinitro-2,5-cyclohexadiene-1,4-dione) as a strong dibasic acid in acidic aqueous media creates the Zundel cation, H5O2(+). The structural unit in a crystal comprises (H5O2)2(+) (2,5-dihydroxy-3,6-dinitro-1,4-benzoquinonate)(2-) dihydrate where the Zundel cation reveals no symmetry, being an ideal case for studying proton dynamics and its stability. The Zundel cation and proton transfer dynamics are studied by variable-temperature X-ray diffraction, IR and solid-state NMR spectroscopy, and various quantum chemical methods, including periodic DFT calculations, ab initio molecular dynamics simulation, and quantization of nuclear motion along three fully coupled internal coordinates. The Zundel cation features a short H-bond with the O···O distance of 2.433(2) Å with an asymmetric placement of hydrogen. The proton potential is of a single well type and, due to the non-symmetric surroundings, of asymmetric shape. The formation of the Zundel cation is facilitated by the electronegative NO2 groups. The employed spectroscopic techniques supported by calculations confirm the presence of a short H-bond with a complex proton dynamics.

Synthesis of nano-sized ZnO particles by co-precipitation method with variation of heating time

DOE Office of Scientific and Technical Information (OSTI.GOV)

Purwaningsih, S. Y., E-mail: sriyanisaputri@gmail.com; Pratapa, S.; Triwikantoro

Zinc oxide powders have been synthesized by a co-precipitation method at low temperature (85 °C), using zinc acetate dihydrate, ammonia, hydrochloric acid solutions as the reactants. A number of process parameters such as reaction temperature, solution basicity or pH and heating time are the main factors affecting the morphology and physical properties of the ZnO nanostructures. In this work the effect of heating time on the morphology and particles size were studied. The as-synthesized ZnO powders were characterized using transmission electron microscopy (TEM) and X-ray diffraction (XRD) techniques. The samples were also analyzed using Fourier transform infrared (FTIR). Rietveld refinementmore » of XRD data confirms that ZnO crystallizes in the hexagonal wurtzite structure with high degree of purity and the (101) plane predominant. The XRD results show that the average crystallite sizes were about 66, 27 and 12 nm for 3, 4 and 5 h of heating times, respectively. The XRD analysis indicated that a fraction of nano-sized ZnO powders were in the form of aggregates, which was also verified by TEM image. The TEM photograph demonstrated that the nano-sized ZnO particles were a pseudo-spherical shape.« less

SCALED-UP SYNTHESIS: SALTS OF CARFENTANIL AND REMIFENTANIL

DTIC Science & Technology

2017-07-01

solution of oxalic acid dihydrate (10.28 g, 80.00 mmol) in 200 mL of isopropanol was added. The mixture was cooled in the refrigerator , and the...acid (2.70 g, 14.05 mmol) in isopropanol. The solution was placed in a refrigerator for 16 h. The precipitate was collected by filtration and washed

Physical characterization of dibasic calcium phosphate dihydrate and anhydrate.

PubMed

Miyazaki, Tamaki; Sivaprakasam, Kannan; Tantry, Jaidev; Suryanarayanan, Raj

2009-03-01

The dehydration of different commercial brands of dibasic calcium phosphate dihydrate (DCPD; CaHPO(4).2H(2)O) was examined over a range of temperatures and water vapor pressures. To determine the main factors affecting the physical stability of DCPD, the baseline characterization of DCPD and dibasic calcium phosphate anhydrate (DCPA; CaHPO(4)) was conducted by thermogravimetric analysis, differential scanning calorimetry and X-ray diffractometry. The surface area and the DCPA content (present as an impurity) depended on the commercial source of DCPD. The larger particles contained a higher concentration of DCPA and the anhydrate exhibited a concentration-dependent acceleratory effect on the dehydration of DCPD. Unlike DCPD, DCPA is physically stable and resisted hydration even when dispersed in water for over 7 months in the temperature range of 4-50 degrees C. In dosage forms containing DCPD, there is a potential for phase transformation to DCPA, while the reverse transition, that is, DCPA --> DCPD appears to be extremely unlikely. Thus, the risk of physical transformation can be minimized by using DCPA in formulations. (c) 2008 Wiley-Liss, Inc. and the American Pharmacists Association

Occurrence and distribution of selected pharmaceuticals and personal care products in aquatic environments: a comparative study of regions in China with different urbanization levels.

PubMed

Chen, Hong; Li, Xiaojuan; Zhu, Saichang

2012-07-01

We analyzed and compared the distributions of 13 target pharmaceuticals in different water samples from the Hangzhou metropolitan area and Linan County, Southeast China. Sampling was conducted in five hospitals, two wastewater treatment plants (WWTPs), and Qiantang River. Samples were concentrated by solid-phase extraction and PPCP concentrations were determined by UPLC-MS/MS. Trimethoprim, erythromycin A dihydrate, norfloxacin, ofloxacin, diclofenac sodium, and atenolol were the most frequently detected pharmaceuticals in hospital effluents. Most of the pharmaceutical concentrations in hospital effluents were higher than those in the WWTP influents. Although both WWTPs adopt the anaerobic-aerobic-anoxic treatment process, the removal rates for pharmaceuticals, such as trimethoprim and diclofenac sodium, were completely different. Meanwhile, erythromycin A dihydrate, ofloxacin, penicillin-G, cephalexin, cefazolin, ibuprofen, and diclofenac sodium were detected in Qiantang River. These results indicate that hospitals are more concentrated sources of pharmaceuticals than WWTPs, and the WWTPs are not the only route of entry of pharmaceuticals into aquatic environments in these two regions.

Fabrication of nanostructured ZnO film as a hole-conducting layer of organic photovoltaic cell

PubMed Central

2013-01-01

We have investigated the effect of fibrous nanostructured ZnO film as a hole-conducting layer on the performance of polymer photovoltaic cells. By increasing the concentration of zinc acetate dihydrate, the changes of performance characteristics were evaluated. Fibrous nanostructured ZnO film was prepared by sol-gel process and annealed on a hot plate. As the concentration of zinc acetate dihydrate increased, ZnO fibrous nanostructure grew from 300 to 600 nm. The obtained ZnO nanostructured fibrous films have taken the shape of a maze-like structure and were characterized by UV-visible absorption, scanning electron microscopy, and X-ray diffraction techniques. The intensity of absorption bands in the ultraviolet region was increased with increasing precursor concentration. The X-ray diffraction studies show that the ZnO fibrous nanostructures became strongly (002)-oriented with increasing concentration of precursor. The bulk heterojunction photovoltaic cells were fabricated using poly(3-hexylthiophene-2,5-diyl) and indene-C60 bisadduct as active layer, and their electrical properties were investigated. The external quantum efficiency of the fabricated device increased with increasing precursor concentration. PMID:23680100

Influence of Sn doping on structural, optical and electrical properties of ZnO thin films prepared by cost effective sol-gel process.

PubMed

Vishwas, M; Narasimha Rao, K; Arjuna Gowda, K V; Chakradhar, R P S

2012-09-01

Tin (Sn) doped zinc oxide (ZnO) thin films were synthesized by sol-gel spin coating method using zinc acetate di-hydrate and tin chloride di-hydrate as the precursor materials. The films were deposited on glass and silicon substrates and annealed at different temperatures in air ambient. The agglomeration of grains was observed by the addition of Sn in ZnO film with an average grain size of 60 nm. The optical properties of the films were studied using UV-VIS-NIR spectrophotometer. The optical band gap energies were estimated at different concentrations of Sn. The MOS capacitors were fabricated using Sn doped ZnO films. The capacitance-voltage (C-V), dissipation vs. voltage (D-V) and current-voltage (I-V) characteristics were studied and the electrical resistivity and dielectric constant were estimated. The porosity and surface area of the films were increased with the doping of Sn which makes these films suitable for opto-electronic applications. Copyright © 2012 Elsevier B.V. All rights reserved.

Evaluation of the thermal stability of a novel strain of live-attenuated mumps vaccine (RS-12 strain) lyophilized in different stabilizers.

PubMed

Jamil, Razieh Kamali; Taqavian, Mohammad; Sadigh, Zohreh-Azita; Shahkarami, Mohammad-Kazem; Esna-Ashari, Fatemeh; Hamkar, Rasool; Hosseini, Seyedeh-Marzieh; Hatami, Alireza

2014-04-01

The stability of live-attenuated viral vaccines is important for immunization efficacy. Here, the thermostabilities of lyophilized live-attenuated mumps vaccine formulations in two different stabilizers, a trehalose dihydrate-based stabilizer and a stabilizer containing sucrose, human serum albumin and sorbitol were investigated using accelerated stability tests at 4°C, 25°C and 37°C at time points between 4h (every 4h for the first 24h) and 1 week. Even under the harshest storage conditions of 37°C for 1 week, the 50% cell culture infective dose (CCID50) determined from titrations in Vero cells dropped by less than 10-fold using each stabilizer formulation and thus complied with the World Health Organization's requirements for the potency of live-attenuated mumps vaccines. However, as the half-life of the RS-12 strain mumps virus infectivity was lengthened substantially at elevated temperatures using the trehalose dihydrate (TD)-based stabilizer, this stabilizer is recommended for vaccine use. Copyright © 2013 Elsevier B.V. All rights reserved.

Investigation of Polar Stratospheric Cloud Solid Particle Formation Mechanisms Using ILAS and AVHRR Observations in the Arctic

NASA Technical Reports Server (NTRS)

Irie, H.; Pagan, K. L.; Tabazadeh, A.; Legg, M. J.; Sugita, T.

2004-01-01

Satellite observations of denitrification and ice clouds in the Arctic lower stratosphere in February 1997 are used with Lagrangian microphysical box model calculations to evaluate nucleation mechanisms of solid polar stratospheric cloud (PSC) particles. The occurrences of ice clouds are not correlated in time and space with the locations of back trajectories of denitrified air masses, indicating that ice particle surfaces are not always a prerequisite for the formation of solid PSCs that lead to denitrification. In contrast, the model calculations incorporating a pseudoheterogeneous freezing process occurring at the vapor-liquid interface can quantitatively explain most of the observed denitrification when the nucleation activation free energy for nitric acid dihydrate formation is raised by only approx.10% relative to the current published values. Once nucleated, the conversion of nitric acid dihydrate to the stable trihydrate phase brings the computed levels of denitrification closer to the measurements. INDEX TERMS: 0305 Atmospheric Composition and Structure: Aerosols and particles (0345, 4801); 0320 Atmospheric Composition and SblctureC: loud physics and chemistry; 0340 Atmospheric Composition and Structure: Middle atmosphere-composition and chemistry

Fabrication of nanostructured ZnO film as a hole-conducting layer of organic photovoltaic cell

NASA Astrophysics Data System (ADS)

Kim, Hyomin; Kwon, Yiseul; Choe, Youngson

2013-05-01

We have investigated the effect of fibrous nanostructured ZnO film as a hole-conducting layer on the performance of polymer photovoltaic cells. By increasing the concentration of zinc acetate dihydrate, the changes of performance characteristics were evaluated. Fibrous nanostructured ZnO film was prepared by sol-gel process and annealed on a hot plate. As the concentration of zinc acetate dihydrate increased, ZnO fibrous nanostructure grew from 300 to 600 nm. The obtained ZnO nanostructured fibrous films have taken the shape of a maze-like structure and were characterized by UV-visible absorption, scanning electron microscopy, and X-ray diffraction techniques. The intensity of absorption bands in the ultraviolet region was increased with increasing precursor concentration. The X-ray diffraction studies show that the ZnO fibrous nanostructures became strongly (002)-oriented with increasing concentration of precursor. The bulk heterojunction photovoltaic cells were fabricated using poly(3-hexylthiophene-2,5-diyl) and indene-C60 bisadduct as active layer, and their electrical properties were investigated. The external quantum efficiency of the fabricated device increased with increasing precursor concentration.

Fabrication of dicalcium phosphate dihydrate-coated β-TCP granules and evaluation of their osteoconductivity using experimental rats.

PubMed

Shariff, Khairul Anuar; Tsuru, Kanji; Ishikawa, Kunio

2017-06-01

β-Tricalcium phosphate (β-TCP) has attracted much attention as an artificial bone substitute owing to its biocompatibility and osteoconductivity. In this study, osteoconductivity of β-TCP bone substitute was enhanced without using growth factors or cells. Dicalcium phosphate dihydrate (DCPD), which is known to possess the highest solubility among calcium phosphates, was coated on β-TCP granules by exposing their surface with acidic calcium phosphate solution. The amount of coated DCPD was regulated by changing the reaction time between β-TCP granules and acidic calcium phosphate solution. Histomorphometry analysis obtained from histological results revealed that the approximately 10mol% DCPD-coated β-TCP granules showed the largest new bone formation compared to DCPD-free β-TCP granules, approximately 2.5mol% DCPD-coated β-TCP granules, or approximately 27mol% DCPD-coated β-TCP granules after 2 and 4weeks of implantation. Based on this finding, we demonstrate that the osteoconductivity of β-TCP granules could be improved by coating their surface with an appropriate amount of DCPD. Copyright © 2017 Elsevier B.V. All rights reserved.

NTP Toxicology and Carcinogenesis Studies of Barium Chloride Dihydrate (CAS No. 10326-27-9) in F344/N Rats and B6C3F1 Mice (Drinking Water Studies).

PubMed

1994-01-01

Barium chloride dihydrate, a white crystalline granule or powder, is used in pigments, aluminum refining, leather tanning and coloring, the manufacture of magnesium metal, ceramics, glass, and paper products, as a pesticide, and in medicine as a cardiac stimulant. Toxicology and carcinogenicity studies were conducted by administering barium chloride dihydrate (99% pure) in drinking water to F344/N rats and B6C3F1 mice for 15 days, 13 weeks, and 2 years. Genetic toxicology studies were conducted in Salmonella typhimurium, cultured Chinese hamster ovary cells, and mouse lymphoma cells. 15-DAY STUDY IN RATS: Groups of five males and five females received barium chloride dihydrate in the drinking water at concentrations of 0, 125, 250, 500, 1,000, or 2,000 ppm for 15 days, corresponding to average daily doses of 10, 15, 35, 60, or 110 mg barium/kg body weight to males and females. No chemical-related deaths, differences in final mean body weights, or clinical findings of toxicity were observed. Water consumption by male and female rats exposed to 2,000 ppm was slightly less (S16%) than controls during week 2. There were no significant differences in absolute or relative organ weights between exposed and control rats. No biologically significant differences in hematology, clinical chemistry, or neurobehavioral parameters occurred in rats. 15-DAY STUDY IN MICE: Groups of five males and five females received barium chloride dihydrate in the drinking water at concentrations of 0, 40, 80,173, 346, or 692 ppm for 15 days, corresponding to average daily doses of 5,10, 20, 40, or 70 mg barium/kg body weight to males and 5, 10, 15, 40, or 85 mg barium/kg body weight to females. No chemical-related deaths, differences in mean body weights or in water consumption, or clinical findings of toxicity were observed in mice. The relative liver weight of males receiving 692 ppm was significantly greater than that of the controls. The absolute and relative liver weights of females that received 692 ppm were significantly greater than those of the controls. No histopathologic evidence of toxicity was observed in mice. 13-WEEK STUDY IN RATS: Groups of 10 males and 10 females received barium chloride dihydrate in the drinking water at concentrations of 0, 125, 500, 1,000, 2,000, or 4,000 ppm for 13 weeks, corresponding to average daily doses of 10, 30, 65, 110, or 200 mg barium/kg body weight to males and 10, 35, 65, 115, or 180 mg barium/kg body weight to females. Three males and one female in the 4,000 ppm groups died during the last week of the study. The final mean body weights of male and female rats receiving 4,000 ppm were significantly lower (13% and 8%) than those of the controls. Water consumption by male and female rats in the 4,000 ppm groups was approximately 30% lower than that by the controls. No clearly chemical-related clinical findings of toxicity or neurobehavioral or cardiovascular effects were noted. Serum phosphorus levels in 2,000 and 4,000 ppm male and female rats were significantly higher than those in controls, but there were no biologically significant differences in hematology parameters or in serum sodium, potassium, or calcium levels. Renal tubule dilatation in the outer stripe of the outer medulla and cortex occurred in male and female rats receiving 4,000 ppm. 13-WEEK STUDY IN MICE: Groups of 10 males and 10 females received barium chloride dihydrate in the drinking water at concentrations of 0, 125, 500, 1,000, 2,000, or 4,000 ppm for 13 weeks, corresponding to average daily doses of 15, 55, 100, 205, or 450 mg barium/kg body weight to males and 15, 60, 110, 200, or 495 mg barium/kg body weight to females. Six males and seven females that received 4,000 ppm and one male that received 125 ppm died during the study. Final mean body weights of male and female mice receiving 4,000 ppm were significantly lower (>30%) than those of controls. Water consumption by male mice in the 4,000 ppm group was 18% lower than that by the controls; water consumption by other exposed groups of male and female mice was similar to thatd groups of male and female mice was similar to that by the controls. Clinical findings of toxicity were limited to debilitation in the surviving male and female mice receiving 4,000 ppm. The absolute and/or relative liver weights of mice receiving 1,000, 2,000, and 4,000 ppm were significantly lower than those of the controls. Multifocal to diffuse nephropathy characterized by tubule dilatation, regeneration, and atrophy occurred in 4,000 ppm male and female mice. 2-YEAR STUDY IN RATS: Groups of 60 males and 60 females received barium chloride dihydrate in the drinking water at concentrations of 0, 500, 1,250, or 2,500 ppm for 104 (males) or 105 weeks (females), corresponding to average daily doses of 15, 30, or 60 mg barium/kg body weight for males and 15, 45, or 75 mg barium/kg body weight for females. The high dose of 2,500 ppm was selected based on decreased final mean body weights, mortality, decreased water consumption, and chemical-related kidney lesions observed in the 4,000 ppm groups in the 13-week study. Survival, Body Weights, Water Consumption, and Clinical Findings: Two-year survival of exposed male and female rats was similar to that of the controls. The final mean body weights of male and female rats that received 2,500 ppm were (5% and 11%) lower than those of controls. Beginning as early as week 5, water consumption by male and female rats receiving 2,500 ppm was substantially lower than that by controls (male: 11% to 30%; female: 19% to 33%). There were no chemical-related clinical findings. Hematology and Clinical Chemistry: There were no chemical-related differences in hematology or clinical chemistry parameters in male or female rats. Special Studies: At the 15-month interim evaluation, the plasma barium concentrations (mg/ml) were significantly increased in males receiving 1,250 and 2,500 ppm and in all exposed groups of females (male: 0 ppm, 0.98; 500 ppm, 1.00; 1,250 ppm, 1.23; 2,500 ppm, 1.68; female: 0 ppm, 0.74; 500 ppm, 0.99; 1,250 ppm, 0.97; 2,500 ppm, 1.43). Barium levels in bone in rats from the 2,500 ppm groups were about 400 times greater than those in the controls. Pathology Findings: At the end of 2 years, there were no increased incidences of neoplasms or nonneoplastic lesions that could be attributed to barium chloride dihydrate. However, there were dose-related decreased incidences of adrenal medulla pheochromocytomas and mononuclear cell leukemia in male rats. 2-YEAR STUDY IN MICE: Groups of 60 males and 60 females received barium chloride dihydrate in the drinking water at concentrations of 0, 500, 1,250, or 2,500 ppm for 103 (males) or 104 weeks (females), corresponding to average daily doses of 30, 75, or 160 mg barium/kg body weight for males and 40, 90, or 200 mg barium/kg body weight for females. The high dose of 2,500 ppm was selected based on decreased final mean body weights, mortality, decreased water consumption, and chemical-related kidney lesions observed in the 4,000 ppm groups in the 13-week study. Survival, Body Weights, Water Consumption, and Clinical Findings: Two-year survival of male and female mice receiving 2,500 ppm was significantly lower than that of the controls due to renal toxicity. Final mean body weights of 2,500 ppm males and females were 9% and 12% lower than those of controls. Water consumption by male and female mice receiving barium chloride was similar to that by the controls. There were no chemical-related clinical findings. Hematology and Clinical Chemistry: There were no differences in hematology or clinical chemistry parameters measured at the 15-month interim evaluation. Special Studies: At the 15-month interim evaluation, plasma barium concentrations (mg/mL) were significantly increased in all exposed groups of mice (male: 0 ppm, 0.62; 500 ppm, 0.77; 1,250 ppm, 0.89; 2,500 ppm, 1.49; female: 0 ppm, 0.52; 500 ppm, 0.74; 1,250 ppm, 1.01; 2,500 ppm, 1.35). Pathology Findings: At the end of the 2-year study, there were increased incidences of nephropathy in male and female mice (male: 1/50, 0/50, 2/48, 19/50; female: 0/50, 2/53, 1/50, 37/54). There were no chemical-related increased incidences of neoplasms in male or female mice. The incidence of hepatocellular adenoma was significantly decreased in male mice receiving 2,500 ppm. GENETIC TOXICOLOGY: Barium chloride dihydrate was not mutagenic in Salmonella typhimurium strains TA97, TA98, TA100, TA1535, or TA1537, with or without exogenous metabolic activation (S9). It was mutagenic in L5178Y mouse lymphoma cells in the presence of S9, but it did not induce sister chromatid exchanges or chromosomal aberrations in cultured Chinese hamster ovary cells, with or without S9. CONCLUSIONS: Under the conditions of these 2-year drinking water studies, there was no evidence of carcinogenic activity of barium chloride dihydrate in male or female F344/N rats that received 500, 1,250, or 2,500 ppm. There was no evidence of carcinogenic activity of barium chloride dihydrate in male or female B6C3F1 mice that received 500, 1,250, or 2,500 ppm. There were chemical-related increased incidences of nephropathy in male and female mice.

Mechanism of groundwater inrush hazard caused by solution mining in a multilayered rock-salt-mining area: a case study in Tongbai, China

NASA Astrophysics Data System (ADS)

Zeng, Bin; Shi, Tingting; Chen, Zhihua; Xiang, Liu; Xiang, Shaopeng; Yang, Muyi

2018-01-01

The solution mining of salt mineral resources may contaminate groundwater and lead to water inrush out of the ground due to brine leakage. Through the example of a serious groundwater inrush hazard in a large salt-mining area in Tongbai County, China, this study mainly aims to analyse the source and channel of the inrushing water. The mining area has three different types of ore beds including trona (trisodium hydrogendicarbonate dihydrate, also sodium sesquicarbonate dihydrate, with the formula Na2CO3 × NaHCO3 × 2H2O, it is a non-marine evaporite mineral), glauber (sodium sulfate, it is the inorganic compound with the formula Na2SO4 as well as several related hydrates) and gypsum (a soft sulfate mineral composed of calcium sulfate dihydrate, with chemical formula CaSO4 × 2H2O). Based on characterisation of the geological and hydrogeological conditions, the hydrochemical data of the groundwater at different points and depths were used to analyse the pollution source and the pollutant component from single or mixed brine by using physical-chemical reaction principle analysis and hydrogeochemical simulation method. Finally, a possible brine leakage connecting the channel to the ground was discussed from both the geological and artificial perspectives. The results reveal that the brine from the trona mine is the major pollution source; there is a NW-SE fissure zone controlled by the geological structure that provides the main channels through which brine can flow into the aquifer around the water inrush regions, with a large number of waste gypsum exploration boreholes channelling the polluted groundwater inrush out of the ground. This research can be a valuable reference for avoiding and assessing groundwater inrush hazards in similar rock-salt-mining areas, which is advantageous for both groundwater quality protection and public health.

Treatment of tooth fracture by medium-energy CO2 laser and DP-bioactive glass paste: the interaction of enamel and DP-bioactive glass paste during irradiation by CO2 laser.

PubMed

Lin, C P; Tseng, Y C; Lin, F H; Liao, J D; Lan, W H

2001-03-01

Acute trauma or trauma associated with occlusal disturbance can produce tooth crack or fracture. Although several methods are proposed to treat the defect, however, the prognosis is generally poor. If the fusion of a tooth fracture by laser is possible, it will offer an alternative to extraction or at least serve as an adjunctive treatment in the reconstruction. We have tried to use a continuous-wave CO2 laser and a newly developed DP-bioactive glass paste (DPGP) to fuse or bridge tooth crack or fracture lines. Both the DP-bioactive glass paste and tooth enamel have strong absorption bands at the wavelength of 10.6 microm. Therefore, under CO2 laser, DPGP and enamel should have an effective absorption and melt together. The interface between DPGP and enamel could be regarded as a mixture of DPGP and enamel (DPG-E). The study focused on the phase transformation, microstructure, functional group and thermal behavior of DPG-E with or without CO2 laser irradiation, by the analytical techniques of XRD, FTIR, DTA/TGA, and SEM. The results of XRD showed that the main crystal phase in the DPG-E was dicalcium phosphate dihydrate (CaHPO4.2H2O). It changed into CaHPO4, gamma-Ca2P2O7, beta-Ca2P2O7 and finally alpha-Ca2P2O7 with increasing temperature. In the FTIR analysis, the 720 cm(-1) absorption band ascribed to the P-O-P linkage in pyrophosphate rose up and the intensities of the OH- bands reduced after laser irradiation. In regard to the results of DTA/TGA after irradiation, the weight loss decreased due to the removal of part of absorption water and crystallization water by the CO2 laser. SEM micrographs revealed that the melted masses and the plate-like crystals formed a tight chemical bond between the enamel and DPGP. We expect that DPGP with the help of CO2 laser can be an alternative to the treatment of tooth crack or fracture.

Polarized electronic spectra for the crystals of three compounds, potassium tetrabromoplatinate(II) dihydrate, tetraethylammonium hexabromodiplatinate(II), and tetra-μ-glycine-dimolybdenum (II) sulfate tetrahydrate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, Timothy Joseph

1977-06-01

The polarized absorption spectra for K 2PtBr 4 . 2H 2O, (N(C 2H 5) 4) 2PtBr 6, and Mo 2(O 2CCH 2NH 3) 4(SO 4) 2 . 4H 2O have been recorded at 300 and 15/sup 0/K. In K 2PtBr 4 . 2H 2O the bands at 24,000 and 27,000 cm -1 in both a- and b-polarizations appear to be vibronically induced. The energy spacing of the vibrational structure was noted to be somewhat higher at 180 cm -1 than for the analogous structure of K 2PtBr 4. The presence of a Pt 2Br 6 -2 impurity gave rise tomore » red sections, which evidently were due to the electron transfer, Pt(IV)/reverse arrow/Pt(II), occurring in c-polarization. Very weak spin-forbidden bands were observable in all three polarizations below 23,500 cm -1. In the crystal spectra of (N(C 2H 5) 4) 2Pt 2Br 6 the transitions were defined with respect to the three molecular axes of the Pt 2Br 6 -2 ion. Excited states were assigned under the D 2sub h/ point group symmetry of the ion. The delocalization of the d electrons gave rise to strongly enhanced intensities for both spin-forbidden and spin-allowed d/reverse arrow/d transitions. The M/reverse arrow/L charge-transfer transitions occur at lower energies in the case of Pt 2Br 6 -2 than in PtBr 4 -2. These charge transfer transitions were found from the polarizations to originate from the terminal bromides. The crystal spectra of Mo 2(O 2CCH 2NH 3) 4(SO 4) 2 . 4H 2O were recorded through the region 20,000 - 25,000 cm -1. The spectra at 15K revealed the vibrational structure in the two recorded polarizations. The electronic transition observed in these spectra was forbidden under the local symmetry of D 4h.« less

Integrated varroa control in honey bee colonies (Apis mellifera carnica) with or without brood

USDA-ARS?s Scientific Manuscript database

Studies were conducted in two apiaries in order to assess the comparative efficacy of oxalic acid (OA), formic acid (FA) and Thymovar against varroa mites in honey bee colonies. Treatments were performed using 85% FA and OA consisted of 2.9% oxalic acid dihydrate and 31.9% sugar in water. Consecutiv...

Solubility and Solubility Product Determination of a Sparingly Soluble Salt: A First-Level Laboratory Experiment

ERIC Educational Resources Information Center

Bonomo, Raffaele P.; Tabbi, Giovanni; Vagliasindi, Laura I.

2012-01-01

A simple experiment was devised to let students determine the solubility and solubility product, "K"[subscript sp], of calcium sulfate dihydrate in a first-level laboratory. The students experimentally work on an intriguing equilibrium law: the constancy of the product of the ion concentrations of a sparingly soluble salt. The determination of…

Potential adherence of gypsum to forage as a consideration for excessive ingestion by ruminates

USDA-ARS?s Scientific Manuscript database

Gypsum (calcium sulfate dihydrate, CaSO4•2H2O) has long been used in agriculture to improve soils and crop production and its use has recently been encouraged by the USDA NRCS for soil conservation through a new National Conservation Practice Standard: Code 333. However, there is concern regarding ...

Gypsum adherence to forage: consideration for excessive ingestion by ruminates

USDA-ARS?s Scientific Manuscript database

Gypsum (calcium sulfate dihydrate, CaSO4•2H2O) has long been used as a soil amendment to improve soil conditions and its use has recently been encouraged by the USDA-NRCS for soil conservation through a new National Conservation Practice Standard: Code 333. However, there is concern regarding the e...

Layer-by-Layer Self-Assembly of Plexcitonic Nanoparticles

DTIC Science & Technology

2013-08-12

nitrate , trisodium citrate tribasic dihydrate, sodium poly(styrene sulfonate) (PSS, MW ~70,000), poly(diallyldimethyl ammonium chloride ) (PDADMAC...Abstract: Colloidal suspensions of multilayer nanoparticles composed of a silver core, a polyelectrolyte spacer layer (inner shell), and a J-aggregate...multilayer architecture served as a framework for examining the coupling of the localized surface plasmon resonance exhibited by the silver core with

Potential adherence of flue gas desulfurization gypsum to forage as a consideration for excessive ingestion by ruminants

USDA-ARS?s Scientific Manuscript database

Gypsum (calcium sulfate dihydrate, CaSO4·2H2O) has long been used to improve soils and crop production, and its use has recently been encouraged by the USDA-NRCS for soil conservation through a new Conservation Practice Standard: Code 333. However, there is concern regarding adverse effects of exce...

Transparent conducting ZnO-CdO mixed oxide thin films grown by the sol-gel method.

PubMed

Pathak, Trilok K; Rajput, Jeevitesh K; Kumar, Vinod; Purohit, L P; Swart, H C; Kroon, R E

2017-02-01

Mixed oxides of zinc and cadmium with different proportions were deposited on ordinary glass substrates using the sol-gel spin coating method under optimized deposition conditions using zinc acetate dihydrate and cadmium acetate dihydrate as precursors. X-ray diffraction patterns confirmed the polycrystalline nature of the films. A combination of cubic CdO and hexagonal wurtzite ZnO phases was observed. The oxidation states of Zn, Cd and O in the deposited films were determined by X-ray photoelectron spectroscopic studies. Surface morphology was studied by scanning electron microscopy and atomic force microscopy. The compositional analysis of the thin films was studied by secondary ion mass spectroscopy. The transmittance of the thin films was measured in the range 300-800nm and the optical bandgap was calculated using Tauc's plot method. The bandgap decreased from 3.15eV to 2.15eV with increasing CdO content. The light emission properties of the ZnO:CdO thin films were studied by photoluminescence spectra recorded at room temperature. The current-voltage characteristics were also assessed and showed ohmic behaviour. The resistance decreased with increasing CdO content. Copyright © 2016 Elsevier Inc. All rights reserved.

13C and (15)N chemical shift tensors in adenosine, guanosine dihydrate, 2'-deoxythymidine, and cytidine.

PubMed

Stueber, Dirk; Grant, David M

2002-09-04

The (13)C and (15)N chemical shift tensor principal values for adenosine, guanosine dihydrate, 2'-deoxythymidine, and cytidine are measured on natural abundance samples. Additionally, the (13)C and (15)N chemical shielding tensor principal values in these four nucleosides are calculated utilizing various theoretical approaches. Embedded ion method (EIM) calculations improve significantly the precision with which the experimental principal values are reproduced over calculations on the corresponding isolated molecules with proton-optimized geometries. The (13)C and (15)N chemical shift tensor orientations are reliably assigned in the molecular frames of the nucleosides based upon chemical shielding tensor calculations employing the EIM. The differences between principal values obtained in EIM calculations and in calculations on isolated molecules with proton positions optimized inside a point charge array are used to estimate the contributions to chemical shielding arising from intermolecular interactions. Moreover, the (13)C and (15)N chemical shift tensor orientations and principal values correlate with the molecular structure and the crystallographic environment for the nucleosides and agree with data obtained previously for related compounds. The effects of variations in certain EIM parameters on the accuracy of the shielding tensor calculations are investigated.

Bilateral symptomatic synovial cysts of the lumbar spine caused by calcium pyrophosphate deposition disease: a case report.

PubMed

Gadgil, Anirudh A; Eisenstein, Stephan M; Darby, Alan; Cassar Pullicino, Victor

2002-10-01

A case of bilateral symptomatic facet joint synovial cysts arising in association with calcium pyrophosphate deposition disease is reported. To present a previously unreported cause for symptomatic synovial cysts of the lumbar spine. Synovial cysts of the facet joints occur most commonly in association with degenerative disease of the spine in older individuals. The association of these cysts with trauma, rheumatoid arthritis, spondylolysis, and kissing spinous processes also has been reported. These cysts can cause symptoms and signs from direct compression of the dura. Chondrocalcinosis has not been previously reported to cause symptomatic synovial cysts. A 67-year-old woman presented with right lower limb sciatica caused by a right L4-L5 facet joint cyst, which resolved after surgical decompression. A year later, she presented with left lower limb sciatica caused by development of a new L4-L5 facet joint cyst, which also resolved after surgical decompression. Histopathologic examination of each cyst showed a cyst wall of fibrous tissue with synovial lining, inflammation, and granulation tissue. Examination of the tissue under polarized light showed positively birefringent, short blunt crystals of calcium pyrophosphate dihydrate. In patients with a history of gout or pseudogout, a rare possibility of a synovial cyst should be considered in the differential diagnosis during investigation for the cause of neural compression resulting in sciatic syndrome.

Diaqua­bis­(4-meth­oxy­benzoato-κO 1)bis­(nicotinamide-κN 1)cobalt(II) dihydrate

PubMed Central

Hökelek, Tuncer; Dal, Hakan; Tercan, Barış; Tenlik, Erdinç; Necefoğlu, Hacali

2010-01-01

In the mononuclear title compound, [Co(C8H7O3)2(C6H6N2O)2(H2O)2]·2H2O, the CoII ion is located on a crystallographic inversion center. The asymmetric unit is completed by one 4-meth­oxy­benzoate anion, one nicotinamide (NA) ligand and one coordinated and one uncoordinated water mol­ecule. All ligands act in a monodentate mode. The four O atoms in the equatorial plane around the CoII ion form a slightly distorted square-planar arrangement, while the slightly distorted octa­hedral coordination is completed by the two pyridine N atoms of the NA ligands in the axial positions. The dihedral angle between the carboxyl­ate group and the attached benzene ring is 6.47 (7)°, while the pyridine and benzene rings are oriented at a dihedral angle of 72.80 (4)°. An O—H⋯O hydrogen bond links the uncoordinated water mol­ecule to one of the carboxyl­ate groups. In the crystal structure, inter­molecular O—H⋯O, N—H⋯O and C—H⋯O hydrogen bonds link the mol­ecules into a three-dimensional network. PMID:21588149

Unusual 2:3:2 complex of DABCO mono-betaine with HCl and H 2O studied by X-ray diffraction, DFT calculations and spectroscopic methods

NASA Astrophysics Data System (ADS)

Barczyński, P.; Dega-Szafran, Z.; Katrusiak, A.; Perdoch, W.; Szafran, M.

2009-12-01

DABCO mono-betaine (1,4-diazabicyclo[2.2.2]octane-1-acetate) forms a complex with HCl and water in the ratio 2:3:2. The crystals are triclinic, space group P1¯. Two non-equivalent molecules of protonated DABCO mono-betaines form a homoconjugated cation through the short and asymmetric O·H·O hydrogen bond of 2.470(3) Å. Two chloride anions are involved in the N-H···Cl hydrogen bonds of 3.049(2) and 3.023(3) Å. The third chloride anion is solvated by the water molecules. The molecules of bis(1,4-diazoniumbicyclo[2.2.2]octane-1-acetate) trihydrochloride dihydrate are linked into comb-like chains by the hydrogen bond formed between water molecules of the neighboring complexes; the O(W)-H···O(W) distance is 2.920(5) Å. FTIR spectrum shows several broad bands attributed to the νO-H, νN-H and νO·H·O vibrations. The structure of three bis(1,4-diazoniumbicyclo[2.2.2]octane-1-acetate) hydrochlorides are optimized at the B3LYP/6-31G(d,p) level of theory and a theoretical IR spectrum is calculated. The values of p Ka of DABCO, DABCO mono- and di-betaines are determined by the potentiometric titration of their hydrohalides.

Sol concentration effect on ZnO nanofibers photocatalytic activity synthesized by sol-gel dip coating method

NASA Astrophysics Data System (ADS)

Toubane, M.; Tala-Ighil, R.; Bensouici, F.; Bououdina, M.; Souier, M.; Liu, S.; Cai, W.; Iratni, A.

2017-03-01

ZnO thin films were deposited onto glass substrate by sol-gel dip coating method. The initial sol concentrations were varied from 0.2 to 0.5 M. Zinc acetate dihydrate, ethanol and Diethanolamine (DEA) were used as staring material, solvent and stabilizer respectively. The evolution of structural, optical properties and methylene blue (MB) photodegradation of the as-deposited films on sol concentration was investigated. Rietveld refinements of x-ray patterns reveal that all the as-prepared thin films have a Zincite-type structure with grain orientation along to c-axis. The strongest sol concentration is favorable for the highest crystallization quality. However, the high preferred orientation factor (POF) occurs for 0.3 M sol concentration. The field emission scanning electron microscopy observations reveals nanofibrous morphology with different lengths. The nanofibers density increases with increasing sols concentrations until forming a flower-like morphology. The EDS analysis confirms the high purity of the as-deposited ZnO films. It is found that all films present good transparency greater than 95% in the visible range; the optical band gap is slightly reduced with the increase in sol concentration. The photocatalytic degradation is enhanced by 90% with the sol concentration. The K app rate reaction increased with increasing sol concentration. The films stability is found to slightly decrease after the third cycle, especially for 0.5 M sol concentration.

Supramolecular architecture of metal-organic frameworks involving dinuclear copper paddle-wheel complexes.

PubMed

Gomathi, Sundaramoorthy; Muthiah, Packianathan Thomas

2013-12-15

The two centrosymmetric dinuclear copper paddle-wheel complexes tetrakis(μ-4-hydroxybenzoato-κ(2)O:O')bis[aquacopper(II)] dimethylformamide disolvate dihydrate, [Cu2(C7H5O3)4(H2O)2]·2C3H7NO·2H2O, (I), and tetrakis(μ-4-methoxybenzoato-κ(2)O:O')bis[(dimethylformamide-κO)copper(II)], [Cu2(C8H7O3)4(C3H7NO)2], (II), crystallize with half of the dinuclear paddle-wheel cage unit in the asymmetric unit and, in addition, complex (I) has one dimethylformamide (DMF) and one water solvent molecule in the asymmetric unit. In both (I) and (II), two Cu(II) ions are bridged by four syn,syn-η(1):η(1):μ carboxylate groups, showing a paddle-wheel cage-type structure with a square-pyramidal coordination geometry. The equatorial positions of (I) and (II) are occupied by the carboxylate groups of 4-hydroxy- and 4-methoxybenzoate ligands, and the axial positions are occupied by aqua and DMF ligands, respectively. The three-dimensional supramolecular metal-organic framework of (I) consists of three different R2(2)(20) and an R4(4)(36) ring motif formed via O-H···O and OW-HW···O hydrogen bonds. Complex (II) simply packs as molecular species.

High-Albedo Salt Crusts on the Tropical Ocean of Snowball Earth: Measurements and Modeling

NASA Astrophysics Data System (ADS)

Carns, R.; Light, B.; Warren, S. G.

2014-12-01

During a Snowball Earth event, almost all of the ocean surface first freezes as sea ice. As in modern sea ice, trapped inclusions of liquid brine permeate the ice cover. As the ice grows and cools, salt crystals precipitate within the inclusions. At -23C, the most abundant salt in seawater, sodium chloride, begins to precipitate as the dihydrate mineral hydrohalite (NaCl·2H2O). Crystals of hydrohalite within the sea ice scatter light. Measurements of cold, natural sea ice show a broadband albedo increase of 10-20% when salt precipitates. Such snow-free natural sea ice with a surface temperature below -23C is rare on modern Earth, but would have been common in tropical regions of a Snowball Earth where evaporation exceeded precipitation. The persistent cold and lack of summer melt on the Snowball ocean surface, combined with net evaporation, is hypothesized to yield lag deposits of hydrohalite crystals on the ice surface. To investigate this process, we prepared laboratory-grown sea ice in a 1000 liter tank in a walk-in freezer laboratory. The ice was cooled below -23 C and the surface sprayed with a 23% NaCl solution to create a layer of hydrohalite-enriched ice, a proxy for lag deposits that would have formed over long periods of surface sublimation. We have developed a novel technique for measuring the spectral albedo of ice surfaces in the laboratory; this technique was used to monitor the evolution of the surface albedo of our salt crust as the ice matrix sublimated away leaving a layer of fine-grained hydrohalite crystals. Measurements of this hydrohalite surface crust show a very high albedo, comparable to fresh snow at visible wavelengths and significantly larger than fresh snow at near infrared wavelengths. Broadband albedos are 0.55 for bare artificial sea ice at -30C, 0.75 for ice containing 25% hydrohalite by volume, 0.84 after five days of desiccation and 0.93 after 47 days of desiccation. Using our laboratory measurements, along with estimates of grain size and crust optical depth, as inputs to Mie scattering and radiative transfer models allowed us to infer the imaginary refractive index of hydrohalite. The model can calculate albedo for pure hydrohalite crusts of varying thickness and for mixtures of ice and hydrohalite. A parameterization is presented for albedo as a function of the thickness of the hydrohalite crust.

Process Parameters on the Crystallization and Morphology of Hydroxyapatite Powders Prepared by a Hydrolysis Method

NASA Astrophysics Data System (ADS)

Wang, Moo-Chin; Hon, Min-Hsiung; Chen, Hui-Ting; Yen, Feng-Lin; Hung, I.-Ming; Ko, Horng-Huey; Shih, Wei-Jen

2013-07-01

The effects of process parameters on the crystallization and morphology of hydroxyapatite (Ca10(PO4)6(OH)2, HA) powders synthesized from dicalcium phosphate dihydrate (CaHPO4·2H2O, DCPD) using a hydrolysis method have been investigated. X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectra, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction (SAED) were used to characterize the synthesized powders. When DCPD underwent hydrolysis in 2.5 NaOH solution (Na(aq)) at 303 K to 348 K (30 °C to 75 °C) for 1 hour, the XRD results revealed that HA was obtained for all the as-dried samples. The SEM morphology of the HA powders for DCPD hydrolysis produced at 348 K (75 °C) shows regular alignment and a short rod shape with a size of 200 nm in length and 50 nm in width. With DCPD hydrolysis in 2.5 M NaOH(aq) holding at 348 K (75 °C) for 1 to 24 hours, XRD results demonstrated that all samples were HA and no other phases could be detected. Moreover, the XRD results also show that all the as-dried powders still maintained the HA structure when DCPD underwent hydrolysis in 0.1 to 5 M NaOH(aq) at 348 K (75 °C) for 1 hour. Otherwise, the full transformation from HA to octa-calcium phosphate (OCP, Ca8H2(PO4)6·5H2O) occurred when hydrolysis happened in 10 M NaOH(aq). FT-IR spectra analysis revealed that some carbonated HA (Ca10(PO4)6(CO3), CHA) had formed. The SEM morphology results show that the 60 to 65 nm width of the uniformly long rods with regular alignment formed in the HA powder aggregates when DCPD underwent hydrolysis in 2.5 M NaOH(aq) at 348 K (75 °C) for 1 hour.

Crystal structures of Sr(ClO4)2·3H2O, Sr(ClO4)2·4H2O and Sr(ClO4)2·9H2O

PubMed Central

Hennings, Erik; Schmidt, Horst; Voigt, Wolfgang

2014-01-01

The title compounds, strontium perchlorate trihydrate {di-μ-aqua-aquadi-μ-perchlorato-strontium, [Sr(ClO4)2(H2O)3]n}, strontium perchlorate tetra­hydrate {di-μ-aqua-bis­(tri­aqua­diperchloratostrontium), [Sr2(ClO4)4(H2O)8]} and strontium perchlorate nona­hydrate {hepta­aqua­diperchloratostrontium dihydrate, [Sr(ClO4)2(H2O)7]·2H2O}, were crystallized at low temperatures according to the solid–liquid phase diagram. The structures of the tri- and tetra­hydrate consist of Sr2+ cations coordinated by five water mol­ecules and four O atoms of four perchlorate tetra­hedra in a distorted tricapped trigonal–prismatic coordination mode. The asymmetric unit of the trihydrate contains two formula units. Two [SrO9] polyhedra in the trihydrate are connected by sharing water mol­ecules and thus forming chains parallel to [100]. In the tetra­hydrate, dimers of two [SrO9] polyhedra connected by two sharing water mol­ecules are formed. The structure of the nona­hydrate contains one Sr2+ cation coordinated by seven water mol­ecules and by two O atoms of two perchlorate tetra­hedra (point group symmetry ..m), forming a tricapped trigonal prism (point group symmetry m2m). The structure contains additional non-coordinating water mol­ecules, which are located on twofold rotation axes. O—H⋯O hydrogen bonds between the water mol­ecules as donor and ClO4 tetra­hedra and water mol­ecules as acceptor groups lead to the formation of a three-dimensional network in each of the three structures. PMID:25552979

Reaction of hydroxy and carbonyl compounds with sulfur tetrafluoride. XVI. Reactions of vicinal dihydric alcohols with sulfur tetrafluoride (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burmakov, A.I.; Hassanein, S.M.; Kunshenko, B.V.

1986-11-20

During the action of sulfur tetrafluoride on ethanediol, d,l-1,2-propanediol, d,l-3,3,3-trifluoro-1,2-propanediol regioselective substitution of one of the hydroxyl groups by a fluorine atom occurs, depending on the electronic nature of the groups present in the molecule. The second hydroxy group in converted into a fluorosulfite group.

Development and Testing of a Colorimetric 96 Well Plate Assay for the Determination of HD Hydrolysis Rate in Various Formulations

DTIC Science & Technology

2005-01-01

Cold Foam 1% ethylene glycol 1% benzalkonium chloride 1% polyvinylpolypyrrolidone 1% Brij 58 1% Benzyldimethyl tetradecyl ammonium chloride dihydrate...described in this report was authorized by the Defense Threat Reduction Agency. This work was started in December 2003 and completed in March 2004. The...LITERA TURE CITED ..................................................................................... 15 5 FIGURES 1. Rates of Chloride Release in

Bis(4,4′-dimethyl-2,2′-bipyridine)oxidovanadium(IV) Sulfate Dehydrate: Potential Candidate for Controlling Lipid Metabolism?

PubMed Central

Gryboś, Ryszard; Krośniak, Mirosław

2017-01-01

Vanadium is a trace element mainly connected with regulation of insulin metabolism which is particularly important in diabetes. In recent years, organic complexes of vanadium seem to be more interesting than inorganic salts. Nevertheless, the effect of vanadium on lipid metabolism is still a problematic issue; therefore, the main purpose of this study was to investigate the effect of 3 organic complexes of vanadium such as sodium (2,2′-bipyridine)oxidobisperoxovanadate(V) octahydrate, bis(2,2′-bipyridine)oxidovanadium(IV) sulfate dehydrate, and bis(4,4′-dimethyl-2,2′-bipyridine)oxidovanadium(IV) sulfate dihydrate in conjunction with high-fat as well as control diet in nondiabetes model on the following lipid parameters: total cholesterol, triglycerides, and high density lipoprotein as well as activity of paraoxonase 1. All of these parameters were determined in plasma of Wistar rats. The most significant effect was observed in case of bis(4,4′-dimethyl-2,2′ bipyridine)oxidovanadium(IV) sulfate dehydrate in rats fed with high-fat diet. Based on our research, bis(4,4′-dimethyl-2,2′-bipyridine)oxidovanadium(IV) sulfate dihydrate should be the aim of further research and perhaps it will be an important factor in the regulation of lipid metabolism. PMID:28529953

Developmental toxicity study of sodium molybdate dihydrate administered in the diet to Sprague Dawley rats.

PubMed

Jay Murray, F; Tyl, Rochelle W; Sullivan, Frank M; Tiwary, Asheesh K; Carey, Sandra

2014-11-01

Molybdenum is an essential nutrient for humans and animals and is a constituent of several important oxidase enzymes. It is normally absorbed from the diet and to a lesser extent from drinking water and the typical human intake is around 2μg/kg bodyweight per day. No developmental toxicity studies to contemporary standards have been published and regulatory decisions have been based primarily on older studies where the nature of the test material, or the actual dose levels consumed is uncertain. In the current study the developmental toxicity of sodium molybdate dihydrate as a representative of a broad class of soluble molybdenum(VI) compounds, was given in the diet to Sprague Dawley rats in accordance with OECD Test Guideline 414. Dose levels of 0, 3, 10, 20 and 40mgMo/kgbw/day were administered from GD6 to GD20. No adverse effects were observed at any dose level on the dams, or on embryofetal survival, fetal bodyweight, or development, with no increase in malformations or variations. Significant increases in serum and tissue copper levels were observed but no toxicity related to these was observed. The NOAEL observed in this study was 40mgMo/kgbw/day, the highest dose tested. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Determination of outer layer and bulk dehydration kinetics of trehalose dihydrate using atomic force microscopy, gravimetric vapour sorption and near infrared spectroscopy.

PubMed

Jones, Matthew D; Beezer, Anthony E; Buckton, Graham

2008-10-01

Knowledge of the kinetics of solid state reactions is important when considering the stability of many medicines. Potentially, such reactions could follow different kinetics on the surface of particles when compared with their interior, yet solid state processes are routinely followed using only bulk characterisation techniques. Atomic force microscopy (AFM) has previously been shown to be a suitable technique for the investigation of surface processes, but has not been combined with bulk techniques in order to analyse surface and bulk kinetics separately. This report therefore describes the investigation of the outer layer and bulk kinetics of the dehydration of trehalose dihydrate at ambient temperature and low humidity, using AFM, dynamic vapour sorption (DVS) and near infrared spectroscopy (NIR). The use of AFM enabled the dehydration kinetics of the outer layers to be determined both directly and from bulk data. There were no significant differences between the outer layer dehydration kinetics determined using these methods. AFM also enabled the bulk-only kinetics to be analysed from the DVS and NIR data. These results suggest that the combination of AFM and bulk characterisation techniques should enable a more complete understanding of the kinetics of certain solid state reactions to be achieved. (c) 2008 Wiley-Liss, Inc. and the American Pharmacists Association

High Pressure Cosmochemistry of Major Planetary Interiors: Laboratory Studies of the Water-rich Region of the System Ammonia-water

NASA Technical Reports Server (NTRS)

Nicol, M.; Johnson, M.; Koumvakalis, A. S.

1985-01-01

The behavior of gas-ice mixtures in major planets at very high pressures was studied. Some relevant pressure-temperature-composition (P-T-X) regions of the hydrogen (H2)-helium (He)-water (H2O-ammonia (NH3)-methane (CH4) phase diagram were determined. The studies, and theoretical model, of the relevant phases, are needed to interpret the compositions of ice-gas systems at conditions of planetary interest. The compositions and structures of a multiphase, multicomponent system at very high pressures care characterized, and the goal is to characterize this system over a wide range of low and high temperatures. The NH3-H2O compositions that are relevant to planetary problems yet are easy to prepare were applied. The P-T surface of water was examined and the corresponding surface for NH3 was determined. The T-X diagram of ammonia-water at atmospheric pressure was studied and two water-rich phases were found, NH3-2H2O (ammonia dihydrate), which melts incongruently, and NH3.H2O (ammonia monohydrate), which is nonstoichiometric and melts at a higher temperature than the dihydrate. It is suggested that a P-T surface at approximately the monohydrate composition and the P-X surface at room temperature is determined.

Evans hole and non linear optical activity in Bis(melaminium) sulphate dihydrate: A vibrational spectral study.

PubMed

Suresh Kumar, V R; Binoy, J; Dawn Dharma Roy, S; Marchewka, M K; Jayakumar, V S

2015-01-01

Bis(melaminium) sulphate dihydrate (BMSD), an interesting melaminium derivative for nonlinear optical activity, has been subjected to vibrational spectral analysis using FT IR and FT Raman spectra. The analysis has been aided by the Potential Energy Distribution (PED) of vibrational spectral bands, derived using density functional theory (DFT) at B3LYP/6-31G(d) level. The geometry is found to correlate well with the XRD structure and the band profiles for certain vibrations in the finger print region have been theoretically explained using Evans hole. The detailed Natural Bond Orbital (NBO) analysis of the hydrogen bonding in BMSD has also been carried out to understand the correlation between the stabilization energy of hyperconjugation of the lone pair of donor with the σ(∗) orbital of hydrogen-acceptor bond and the strength of hydrogen bond. The theoretical calculation shows that BMSD has NLO efficiency, 2.66 times that of urea. The frontier molecular orbital analysis points to a charge transfer, which contributes to NLO activity, through N-H…O intermolecular hydrogen bonding between the melaminium ring and the sulphate. The molecular electrostatic potential (MEP) mapping has also been performed for the detailed analysis of the mutual interactions between melaminium ring and sulphate ion. Copyright © 2015 Elsevier B.V. All rights reserved.

Plasma shield lasertripsy: in vitro studies.

PubMed

Bhatta, K M; Rosen, D I; Dretler, S P

1989-10-01

A technique for safer and more effective pulsed laser lithotripsy of urinary and biliary calculi was investigated in vitro. The technique involves enclosing the distal end of the laser delivery fiber in a "plasma shield." The plasma shield is a specially designed metal cap that serves to transfer the laser-induced mechanical impulse to the calculus while shielding surrounding tissue from direct laser exposure and thermal radiation. The metal cap also offers the advantage of effectively blunting the sharp fiber tip and improving its visualization under fluoroscopy. Plasma shield lithotripsy using a 200 micron quartz fiber inserted into a section of a modified 0.034 in. diameter stainless steel guide wire was tested in vitro on a variety of calculi and compared with results obtained using a 200 micron laser fiber applied directly. Calculi tested included cystine, struvite and calcium oxalate dihydrate urinary stones and pigmented cholesterol gallstones. The laser source was a flashlamp-pumped dye laser producing pulses of 1.2 microsecond duration and operated at a wavelength of 504 nm and pulse repetition frequency of 5 Hz. The results show that plasma shield lasertripsy is as effective as direct lasertripsy for fragmenting gallstones, struvite and calcium oxalate dihydrate calculi, is potentially safer, and can fragment cystine calculi which the pulsed dye laser applied directly cannot.

Tinnunculite, C5H4N4O3 · 2H2O: Occurrences on the Kola Peninsula and Redefinition and Validation as a Mineral Species

NASA Astrophysics Data System (ADS)

Pekov, I. V.; Chukanov, N. V.; Yapaskurt, V. O.; Belakovskiy, D. I.; Lykova, I. S.; Zubkova, N. V.; Shcherbakova, E. P.; Britvin, S. N.; Chervonnyi, A. D.

2017-12-01

Based on a study of samples found in the Khibiny (Mt. Rasvumchorr: the holotype) and Lovozero (Mts Alluaiv and Vavnbed) alkaline complexes on the Kola Peninsula, Russia, tinnunculite was approved by the IMA Commission on New Minerals, Nomenclature, and Classification as a valid mineral species (IMA no. 2015-02la) and, taking into account a revisory examination of the original material from burnt dumps of coal mines in the southern Urals, it was redefined as crystalline uric acid dihydrate (UAD), C5H4N4O3 · 2H2O. Tinnunculite is poultry manure mineralized in biogeochemical systems, which could be defined as "guano microdeposits." The mineral occurs as prismatic or tabular crystals up to 0.01 × 0.1 × 0.2 mm in size and clusters of them, as well as crystalline or microglobular crusts. Tinnunculite is transparent or translucent, colorless, white, yellowish, reddish or pale lilac. Crystals show vitreous luster. The mineral is soft and brittle, with a distinct (010) cleavage. D calc = 1.68 g/cm3 (holotype). Tinnunculite is optically biaxial (-), α = 1.503(3), β = 1.712(3), γ = 1.74(1), 2 V obs = 40(10)°. The IR spectrum is given. The chemical composition of the holotype sample (electron microprobe data, content of H is calculated by UAD stoichiometry) is as follows, wt %: 37.5 O, 28.4 C, 27.0 N, 3.8 Hcalc, total 96.7. The empirical formula calculated on the basis of (C + N+ O) = 14 apfu is: C4.99H8N4.07O4.94. Tinnunculite is monoclinic, space group (by analogy with synthetic UAD) P21/ c. The unit cell parameters of the holotype sample (single crystal XRD data) are a = 7.37(4), b = 6.326(16), c = 17.59(4) Å, β = 90(1)°, V = 820(5) Å3, Z = 4. The strongest reflections in the XRD pattern ( d, Å- I[ hkl]) are 8.82-84[002], 5.97-15[011], 5.63-24[102̅, 102], 4.22-22[112], 3.24-27[114̅,114], 3.18-100[210], 3.12-44[211̅, 211], 2.576-14[024].

Use of Vegetable Oil in Reductive Dechlorination of Tetrachloroethene

DTIC Science & Technology

2001-08-01

12.5 g sodium bicarbonate (Fisher Scientific Co.), and 4.412 g of citric acid , trisodium salt dihydrate (99%, Aldrich 62 Chemical Co. Inc.) to 1 L of...relatively quickly, leading to low donor efficiency. Biomass and acetate were the most significant products of vegoil- fed microcosms. Volatile fatty acids ...longer than 2 carbons rarely persisted. Since these acids can act as good secondary donors in the aqueous phase, their absence implies that the

[May renal lithiasis be really prevented? New trends and therapeutic tools.

PubMed

Grases, Félix; Costa-Bauzá, Antonia; Prieto, Rafael M

2017-01-01

Renal calculi are generally formed as a result of the combination of certain factors, some related to urine composition (concentration of lithogenic substances, deficiency of crystallization inhibitors, presence of heterogeneous nucleants) and others with renal morphology and anatomy (urinary tract stasis, low urodynamic efficiency cavities, morpho-anatomic deformations, renal papillary tissue lesions). In fact, the composition, macrostructure and microstructure of the calculus will clearly depend on the factors that have induced it. For this reason, the appropriate study and classification of the renal calculi simplifies the diagnosis and allows a more effective therapeutic approach since it can be oriented to directly correct the etiological factors responsible for stone formation. In this article, we review the main etiological factors involved in the formation of each type of calculus and the prophylactic measures that can be adopted for proper correction. The most frequent kidney stones have been classified into the following types: calcium oxalate monohydrate papillary calculi, calcium oxalate monohydrate non-papillary calculi, calcium oxalate dihydrate calculi, mixed hydroxyapatite/ calcium oxalate calculi, carboxyapatite/hydroxyapatite calculi, brushite calculi, struvite/carboxyapatite calculi, uric acid calculi, uric acid/calcium oxalate monohydrate calculi, and cystine calculi. Occasionally, however, the calculus is not available for study, in which case the only way forward is to use all available information (clinical history, life habits, radiological data), together with basic biochemical information, to identify and correct all etiological factors related to renal lithiasis that have been identified.

Structure disordering and thermal decomposition of manganese oxalate dihydrate, MnC2O4·2H2O

NASA Astrophysics Data System (ADS)

Puzan, Anna N.; Baumer, Vyacheslav N.; Lisovytskiy, Dmytro V.; Mateychenko, Pavel V.

2018-04-01

It is found that the known regular structures of MnC2O4·2H2O (I) do not allow to refine the powder X-ray pattern of (I) properly using the Rietveld method. Implementation of order-disorder scheme [28] via the including of appropriate displacement vector improves the refinement results. Also it is found that in the case of (I) the similar improvement may be achieved using the data on two phases of (I) obtained as result of decomposition MnC2O4·3H2O single crystal in the mother solution after growth. Thermal decomposition of (I) produce the anhydrous γ-MnC2O4 (II) the structure of which is differ from the known α- and β-modifications of VIIIb transition metal oxalates. The solved ab initio from the powder pattern structure (II) (space group Pmna, a = 7.1333 (1), b = 5.8787 (1), c = 9.0186 (2) Å, V = 378.19 (1) Å3, Z = 4 and Dx = 2.511 Mg m-3) contains seven-coordinated Mn atoms with Mn-O distances of 2.110-2.358 Å, and is not close-packed. Thermal decomposition of (II) in air flows via forming of amorphous MnO, the heating of which up to 723 K is accompanied by oxidation of MnO to Mn2O3 and further recrystallization of the latter.

KCd2[N(CN)2]5(H2O)4: an enmeshed honeycomb grid.

PubMed

Schlueter, John A; Geiser, Urs; Funk, Kylee A

2008-02-01

The title compound, poly[potassium [diaquapenta-micro(2)-dicyanamido-dicadmium(II)] dihydrate], {K[Cd(2)(C(2)N(3))(5)(H(2)O)(2)].2H(2)O}(n), contains two-dimensional anionic sheets of {[Cd(2){N(CN)(2)}(H(2)O)(2)](-)}(n) with a modified (6,3)-net (layer group cm2m, No. 35). Two sets of equivalent sheets interpenetrate orthogonally to form a tetragonal enmeshed grid.

Familial chondrocalcinosis in the Spanish population.

PubMed

Fernandez Dapica, M P; Gómez-Reino, J J

1986-06-01

We have found in our clinic a 28.1% prevalence of familial chondrocalcinosis among 149 family members of 32 patients with calcium pyrophosphate dihydrate deposition disease. The clinical and radiological characteristics of these familial chondrocalcinosis patients were similar to those of the Chiloes with familial chondrocalcinosis previously reported. No significant clinical or radiological differences were detected between our sporadic and familial chondrocalcinosis patients. Our findings support the hypothesis that the Chiloes familial chondrocalcinosis was carried to Chile by Spanish immigrants.

Dry powder aerosols generated by standardized entrainment tubes from alternative sugar blends: 3. Trehalose dihydrate and D-mannitol carriers.

PubMed

Mansour, Heidi M; Xu, Zhen; Hickey, Anthony J

2010-08-01

The relationship between physicochemical properties of drug/carrier blends and aerosol drug powder delivery was evaluated. Four pulmonary drugs each representing the major pulmonary therapeutic classes and with a different pharmacological action were employed. Specifically, the four pulmonary drugs were albuterol sulfate, ipratropium bromide monohydrate, disodium cromoglycate, and fluticasone propionate. The two carrier sugars, each representing a different sugar class, were D-mannitol and trehalose dihydrate. Dry powder aerosols (2%, w/w, drug in carrier) delivered using standardized entrainment tubes (SETs) were characterized by twin-stage liquid impinger. The fine particle fraction (FPF) was correlated with SET shear stress, tau(s), and the maximum fine particle fraction (FPF(max)) was correlated with a deaggregation constant, k(d), by using a powder aerosol deaggregation equation (PADE) by nonlinear and linear regression analyses applied to pharmaceutical inhalation aerosol systems in the solid state. For the four pulmonary drugs representing the major pulmonary therapeutic classes and two chemically distinct pulmonary sugar carriers (non-lactose types) aerosolized with SETs having well-defined shear stress values, excellent correlation and predictive relationships were demonstrated for the novel and rigorous application of PADE for dry powder inhalation aerosol dispersion within a well-defined shear stress range, in the context of pulmonary drug/sugar carrier physicochemical and interfacial properties. (c) 2010 Wiley-Liss, Inc. and the American Pharmacists Association

Evaluation of carbonate apatite blocks fabricated from dicalcium phosphate dihydrate blocks for reconstruction of rabbit femoral and tibial defects.

PubMed

Kanazawa, Masayuki; Tsuru, Kanji; Fukuda, Naoyuki; Sakemi, Yuta; Nakashima, Yasuharu; Ishikawa, Kunio

2017-06-01

This study aimed to evaluate in vivo behavior of a carbonate apatite (CO 3 Ap) block fabricated by compositional transformation via a dissolution-precipitation reaction using a calcium hydrogen phosphate dihydrate [DCPD: CaHPO 4 ·2H 2 O] block as a precursor. These blocks were used to reconstruct defects in the femur and tibia of rabbits, using sintered dense hydroxyapatite (HAp) blocks as the control. Both the CO 3 Ap and HAp blocks showed excellent tissue response and good osteoconductivity. HAp block maintained its structure even after 24 weeks of implantation, so no bone replacement of the implant was observed throughout the post-implantation period in either femoral or tibial bone defects. In contrast, CO 3 Ap was resorbed with increasing time after implantation and replaced with new bone. The CO 3 Ap block was resorbed approximately twice as fast at the metaphysis of the proximal tibia than at the epiphysis of the distal femur. The CO 3 Ap block was resorbed at an approximately linear change over time, with complete resorption was estimated by extrapolation of data at approximately 1-1.5 years. Hence, the CO 3 Ap block fabricated in this study has potential value as an ideal artificial bone substitute because of its resorption and subsequent replacement by bone.

Identification of mineral compositions in some renal calculi by FT Raman and IR spectral analysis

NASA Astrophysics Data System (ADS)

Tonannavar, J.; Deshpande, Gouri; Yenagi, Jayashree; Patil, Siddanagouda B.; Patil, Nikhil A.; Mulimani, B. G.

2016-02-01

We present in this paper accurate and reliable Raman and IR spectral identification of mineral constituents in nine samples of renal calculi (kidney stones) removed from patients suffering from nephrolithiasis. The identified mineral components include Calcium Oxalate Monohydrate (COM, whewellite), Calcium Oxalate Dihydrate (COD, weddellite), Magnesium Ammonium Phosphate Hexahydrate (MAPH, struvite), Calcium Hydrogen Phosphate Dihydrate (CHPD, brushite), Pentacalcium Hydroxy Triphosphate (PCHT, hydroxyapatite) and Uric Acid (UA). The identification is based on a satisfactory assignment of all the observed IR and Raman bands (3500-400 cm- 1) to chemical functional groups of mineral components in the samples, aided by spectral analysis of pure materials of COM, MAPH, CHPD and UA. It is found that the eight samples are composed of COM as the common component, the other mineral species as common components are: MAPH in five samples, PCHT in three samples, COD in three samples, UA in three samples and CHPD in two samples. One sample is wholly composed of UA as a single component; this inference is supported by the good agreement between ab initio density functional theoretical spectra and experimental spectral measurements of both sample and pure material. A combined application of Raman and IR techniques has shown that, where the IR is ambiguous, the Raman analysis can differentiate COD from COM and PCHT from MAPH.

Identification of mineral compositions in some renal calculi by FT Raman and IR spectral analysis.

PubMed

Tonannavar, J; Deshpande, Gouri; Yenagi, Jayashree; Patil, Siddanagouda B; Patil, Nikhil A; Mulimani, B G

2016-02-05

We present in this paper accurate and reliable Raman and IR spectral identification of mineral constituents in nine samples of renal calculi (kidney stones) removed from patients suffering from nephrolithiasis. The identified mineral components include Calcium Oxalate Monohydrate (COM, whewellite), Calcium Oxalate Dihydrate (COD, weddellite), Magnesium Ammonium Phosphate Hexahydrate (MAPH, struvite), Calcium Hydrogen Phosphate Dihydrate (CHPD, brushite), Pentacalcium Hydroxy Triphosphate (PCHT, hydroxyapatite) and Uric Acid (UA). The identification is based on a satisfactory assignment of all the observed IR and Raman bands (3500-400c m(-1)) to chemical functional groups of mineral components in the samples, aided by spectral analysis of pure materials of COM, MAPH, CHPD and UA. It is found that the eight samples are composed of COM as the common component, the other mineral species as common components are: MAPH in five samples, PCHT in three samples, COD in three samples, UA in three samples and CHPD in two samples. One sample is wholly composed of UA as a single component; this inference is supported by the good agreement between ab initio density functional theoretical spectra and experimental spectral measurements of both sample and pure material. A combined application of Raman and IR techniques has shown that, where the IR is ambiguous, the Raman analysis can differentiate COD from COM and PCHT from MAPH. Copyright © 2015 Elsevier B.V. All rights reserved.

Three-Dimensional Analysis of the Contact Pattern between the Cortical Bone and Femoral Prosthesis after Cementless Total Hip Arthroplasty

PubMed Central

Mishima, Hajime; Sugaya, Hisashi; Nishino, Tomofumi; Yamazaki, Masashi

2016-01-01

The cementless stem Excia (B. Braun, Melsungen, Germany) implant has a rectangular cross-sectional shape with back-and-forth flanges and a plasma-sprayed, dicalcium phosphate dihydrate coating from the middle to proximal portion to increase initial fixation and early bone formation. Here, the conformity of the Excia stem to the femoral canal morphology was three-dimensionally assessed using computed tomography. Forty-three patients (45 hips) were examined after primary total hip arthroplasty with a mean follow-up of 27 ± 3 months (range: 24–36 months). Spot welds occurred at zone 2 in 16 hips and at zone 6 in 24 hips, with 83% (20/24 hips) of those occurring within 3 months after surgery. First- (n = 12 hips), second- (n = 32), and third- (n = 1) degree stress shielding were observed. The stem was typically in contact with the cortical bone in the anterolateral mid-portion (100%) and posteromedial distal portions (85%). Stress shielding did not progress, even in cases where the stems were in contact with the distal portions. The anterior flange was in contact with the bone in all cases. The stability of the mid-lateral portion with the dicalcium phosphate dihydrate coating and the anterior flange may have inhibited the progression of stress shielding beyond the second degree. PMID:26881087

Evaluation of a Particulate Filtration System for an Alkaline Paint Stripper at Letterkenny Army Depot

DTIC Science & Technology

1991-08-01

hydroxide 66.0 17.5 1 Mineral seal oil 1.00 0.26 1.00 Fluorochemical surfactant 0.02 0.005 0.02 Sodiun carbonate 1.62 0.43 5.00 Sulfunated oleic acid ...specified rejuvenating additive is currently not added to the solution at LEAD. d Sodium salt of N-hydroxyethylethylenediamine triacetic acid , dihydrate...methylene chloride) and formic acid or I abrasive blasting. Aluminum parts are not stripped in alkaline solutions because these solutions chemically attack

Study on environmental stability of a Zn based metal chelate organic small molecule in powder and thin films

NASA Astrophysics Data System (ADS)

Shukla, Vivek Kumar; Maitra, Jaya

2013-06-01

The organic small molecules like Bis (8-hydroxy quinoline) Zinc, (Znq2), used in organic light emitting diodes (OLEDs) are sensitive to environment species like moisture and air. Using characterization tools like photoluminescence (PL), FTIR and DSC, we investigated that as deposited films of Znq2 have a significant component of Znq2 tetramer and less dihydrate component. The stability of films deposited at higher deposition rates may be due to higher component of tetramer.

Preliminary In Vitro Evaluation of an Adjunctive Therapy for Extremity Wound Infection Reduction: Rapidly Resorbing Local Antibiotic Delivery

DTIC Science & Technology

2009-07-01

activity of fast- degrading drug delivery vehicles made from cellulose binder and calcium sulfate dihydrate and from conven- tional calcium sulfate...investigations are planned to deter- mine if the in vitro findings of this study correlate to reduced risk of infection, biofilm formation, patient...of bacteria in biofilms . Lancet 358:135–138. 31. Donlan RM. 2002. Biofilms : microbial life on surfaces. Emerg Infect Dis 8:881–890. 32. Sarkisova S

Time-Resolved Infrared Reflectance Studies of the Dehydration-Induced Transformation of Uranyl Nitrate Hexahydrate to the Trihydrate Form

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Timothy J.; Sweet, Lucas E.; Meier, David E.

Uranyl nitrate is a key species in the nuclear fuel cycle. However, this species is known to exist in different states of hydration, including the hexahydrate ([UO2(NO3)2(H2O)6] often called UNH), the trihydrate [UO2(NO3)2(H2O)3 or UNT], and in very dry environments the dihydrate form [UO2(NO3)2(H2O)2]. Their relative stabilities depend on both water vapor pressure and temperature. In the 1950s and 1960s the different phases were studied by infrared transmission spectroscopy, but were limited both by instrumental resolution and by the ability to prepare the samples for transmission. We have revisited this problem using time-resolved reflectance spectroscopy, which requires no sample preparationmore » and allows dynamic analysis while the sample is exposed to a flow of N2 gas. Samples of known hydration state were prepared and confirmed via X-ray diffraction patterns of known species. In reflectance mode the hexahydrate UO2(NO3)2(H2O)6 has a distinct uranyl asymmetric stretch band at 949.0 cm-1 that shifts to shorter wavelengths and broadens as the sample desiccates and recrystallizes to the trihydrate, first as a shoulder growing in on the blue edge but ultimately results in a doublet band with reflectance peaks at 966 and 957 cm-1. The data are consistent with transformation from UNH to UNT as UNT has two inequivalent UO22+ sites. The dehydration of UO2(NO3)2(H2O)6 to UO2(NO3)2(H2O)3 is both a structural and morphological change that has the lustrous lime green UO2(NO3)2(H2O)6 crystals changing to the matte greenish yellow of the trihydrate solid. The phase transformation and crystal structures were confirmed by density functional theory calculations and optical microscopy methods, both of which showed a transformation with two distinct sites for the uranyl cation in the trihydrate, with but one in the hexahydrate.« less

Calcium-43 chemical shift and electric field gradient tensor interplay: a sensitive probe of structure, polymorphism, and hydration.

PubMed

Widdifield, Cory M; Moudrakovski, Igor; Bryce, David L

2014-07-14

Calcium is the 5th most abundant element on earth, and is found in numerous biological tissues, proteins, materials, and increasingly in catalysts. However, due to a number of unfavourable nuclear properties, such as a low magnetogyric ratio, very low natural abundance, and its nuclear electric quadrupole moment, development of solid-state (43)Ca NMR has been constrained relative to similar nuclides. In this study, 12 commonly-available calcium compounds are analyzed via(43)Ca solid-state NMR and the information which may be obtained by the measurement of both the (43)Ca electric field gradient (EFG) and chemical shift tensors (the latter of which are extremely rare with only a handful of literature examples) is discussed. Combined with density functional theory (DFT) computations, this 'tensor interplay' is, for the first time for (43)Ca, illustrated to be diagnostic in distinguishing polymorphs (e.g., calcium formate), and the degree of hydration (e.g., CaCl2·2H2O and calcium tartrate tetrahydrate). For Ca(OH)2, we outline the first example of (1)H to (43)Ca cross-polarization on a sample at natural abundance in (43)Ca. Using prior knowledge of the relationship between the isotropic calcium chemical shift and the calcium quadrupolar coupling constant (CQ) with coordination number, we postulate the coordination number in a sample of calcium levulinate dihydrate, which does not have a known crystal structure. Natural samples of CaCO3 (aragonite polymorph) are used to show that the synthetic structure is present in nature. Gauge-including projector augmented-wave (GIPAW) DFT computations using accepted crystal structures for many of these systems generally result in calculated NMR tensor parameters which are in very good agreement with the experimental observations. This combination of (43)Ca NMR measurements with GIPAW DFT ultimately allows us to establish clear correlations between various solid-state (43)Ca NMR observables and selected structural parameters, such as unit cell dimensions and average Ca-O bond distances.

Time-resolved infrared reflectance studies of the dehydration-induced transformation of uranyl nitrate hexahydrate to the trihydrate form

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Timothy J.; Sweet, Lucas E.; Meier, David E.

2015-09-08

Uranyl nitrate is a key species in the nuclear fuel cycle. However, this species is known to exist in different states of hydration, including the hexahydrate ([UO 2(NO 3) 2(H 2O) 6] often called UNH), the trihydrate [UO 2(NO 3) 2(H 2O) 3 or UNT], and in very dry environments the dihydrate form [UO 2(NO 3) 2(H 2O) 2]. Their relative stabilities depend on both water vapor pressure and temperature. In the 1950s and 1960s, the different phases were studied by infrared transmission spectroscopy but were limited both by instrumental resolution and by the ability to prepare the samples formore » transmission. We have revisited this problem using time-resolved reflectance spectroscopy, which requires no sample preparation and allows dynamic analysis while the sample is exposed to a flow of N 2 gas. Samples of known hydration state were prepared and confirmed via X-ray diffraction patterns of known species. In reflectance mode the hexahydrate UO 2(NO 3) 2(H 2O) 6 has a distinct uranyl asymmetric stretch band at 949.0 cm –1 that shifts to shorter wavelengths and broadens as the sample desiccates and recrystallizes to the trihydrate, first as a shoulder growing in on the blue edge but ultimately results in a doublet band with reflectance peaks at 966 and 957 cm –1. The data are consistent with transformation from UNH to UNT as UNT has two inequivalent UO 2 2+ sites. The dehydration of UO 2(NO 3) 2(H 2O) 6 to UO 2(NO 3) 2(H 2O) 3 is both a structural and morphological change that has the lustrous lime green UO 2(NO 3) 2(H 2O) 6 crystals changing to the matte greenish yellow of the trihydrate solid. As a result, the phase transformation and crystal structures were confirmed by density functional theory calculations and optical microscopy methods, both of which showed a transformation with two distinct sites for the uranyl cation in the trihydrate, with only one in the hexahydrate.« less

Development of zinc oxide nanoparticle by sonochemical method and study of their physical and optical properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khan, Samreen Heena, E-mail: samreen.heena.khan@gmail.com; Suriyaprabha, R.; Pathak, Bhawana, E-mail: bhawana.pathak@cug.ac.in

With the miniaturization of crystal size, the fraction of under-coordinated surface atoms becomes dominant, and hence, materials in the nano-regime behave very differently from the similar material in a bulk. Zinc oxide (ZnO), particularly, exhibits extraordinary properties such as a wide direct band gap (3.37 eV), large excitation binding energy (60 meV), low refractive index (1.9), stability to intense ultraviolet (UV) illumination, resistance to high-energy irradiation, and lower toxicity as compared to other semiconductors. This very property makes Zinc Oxide a potential candidate in many application fields, particularly as a prominent semiconductor. Zinc Oxide plays a significant role in manymore » technological advances with its application in semiconductor mediated photocatalytic processes and sensor, solar cells and others. In present study, Zinc Oxide (ZnO) has been synthesized using three different precursors by sonochemical method. Zinc Acetate Dihydrate, Zinc Nitrate Hexahydrate and Zinc Sulphate Heptahydrate used as a precursor for the synthesis process. The synthesized ZnO nanoparticle has been found under the range of ∼50 nm. Zinc oxide nanoparticles were characterized using different characterizing tools. The as-synthesized ZnO was characterized by Fourier Transform-Infrared Spectroscopy (FT-IR) for the determination of functional group; Scanning Electron Microscopy equipped with Energy Dispersive Spectroscopy (SEM-EDS) for Morphology and elemental detection respectively, Transmission Electron Microscopy for Particle size distribution and morphology and X-Ray Diffraction (XRD) for the confirmation of crystal structure of the nanomaterial. The optical properties of the ZnO were examined by UV-VIS spectroscopy equipped with Diffuse Reflectance spectroscopy (DRS) confirmed the optical band gap of ZnO-3 around 3.23 eV resembles with the band gap of bulk ZnO (3.37eV). The TEM micrograph of the as-synthesized material showed perfectly spherical shaped nanoparticle under the size range of 50nm. The XRD data showed that the ZnO-3 which was synthesized using Zinc Nitrate Hexahydrate as precursor showed the hexagonal wurtzite crystal structure. The XRD data obtained were compared with the JCPDS standard data. The precursor Zinc Nitrate Hexahydrate (ZnO-3) showed the good yield, monodispersity and size of nanoparticle under the range of 50 nm. The ZnO nanoparticles synthesize using different precursor was found effective in order of ZnO-3, followed by ZnO-1 & ZnO-2. The Synthesized ZnO has wider application in environmental remediation and clean-up as a potential nano-catalyst.« less

Dibasic calcium phosphate dihydrate, USP material compatibility with gamma radiation

NASA Astrophysics Data System (ADS)

Betancourt Quiles, Maritza

Gamma radiation is a commonly used method to reduce the microbial bioburden in compatible materials when it is applied at appropriate dose levels. Gamma irradiation kills bacteria and mold by breaking down the organism’s DNA and inhibiting cell division. The purpose of this study is to determine the radiation dosage to be used to treat Dibasic Calcium Phosphate Dihydrate, USP (DCPD) and to evaluate its physicochemical effects if any, on this material. This material will be submitted to various doses of gamma radiation that were selected based on literature review and existing regulations that demonstrate that this method is effective to reduce or eliminate microbial bioburden in natural source and synthetic materials. Analytical testing was conducted to the DCPD exposed material in order to demonstrate that gamma radiation does not alter the physicochemical properties and material still acceptable for use in the manufacture of pharmaceutical products. The results obtained through this study were satisfactory and demonstrated that the gamma irradiation dosages from 5 to 30 kGy can be applied to DCPD without altering its physicochemical properties. These are supported by the Assay test data evaluation of lots tested before and after gamma irradiation implementation that show no significant statistical difference between irradiated and non irradiated assay results. The results of this study represent an achievement for the industry since they provide as an alternative the use of Gamma irradiation technology to control the microbial growth in DCPD.

The influence of various excipients on the conversion kinetics of carbamazepine polymorphs in aqueous suspension.

PubMed

Tian, Fang; Saville, Dorothy J; Gordon, Keith C; Strachan, Clare J; Zeitler, J Axel; Sandler, Niklas; Rades, Thomas

2007-02-01

The influence of various excipients on the conversion of carbamazepine polymorphs to the dihydrate in aqueous suspension has been investigated. Ten excipients having functional groups which were potentially able to form hydrogen bonds with carbamazepine (group 1: methylcellulose, hypromellose (hydroxypropyl methylcellulose), hydroxypropylcellulose (HPC), 2-hydroxyethylcellulose (HEC), carmellose sodium (sodium carboxymethylcellulose), cellobiose; group 2: povidone (polyvinylpyrrolidone), povidone-vinyl acetate copolymer (povidone/VA) and N-methyl-2-pyrrolidone; group 3: macrogol (polyethylene glycol) and polyethylene oxide-polypropylene oxide copolymer (PEO/PPO)) were selected. Carbamazepine polymorphic forms III and I were dispersed separately into each aqueous excipient solution (0.1%, w/v) for 30 min at room temperature. The inhibition effect of each excipient was quantified using Raman spectroscopy combined with multivariate analyses. The solubility parameter of each excipient was calculated and used for categorizing excipients. Excipients in groups 1 and 2, which had both low solubility parameters (< 27.0 MPa(1/2)) and strong hydrogen bonding groups, inhibited the conversion completely. With increasing solubility parameter, the inhibition effect decreased for group 1 excipients, especially for carbamazepine form I, which had a higher specific surface area. Also, the excipients of group 3, lacking strong hydrogen bonding groups, showed poor inhibition although they had low solubility parameters (< 21.0 MPa(1/2)). This study indicated the importance of both hydrogen bonding interaction and a suitable hydrophobicity (expressed by the solubility parameter) in the inhibition of the conversion of carbamazepine to the dihydrate.

Partitions for high-rise construction using phosphogypsum

NASA Astrophysics Data System (ADS)

Zolotukhin, Sergey; Kukina, Olga; Abramenko, Anatoly

2018-03-01

Gypsum blocks are usually used to make partitions in highrise construction. Reducing the cost of materials used in high-rise construction is an urgent task of modern material science. Phosphogypsum dihydrate, which has binding properties, is one of the large-tonnage waste. The authors have proved that, after years of storage in heaps, water-soluble phosphates, fluorides and other additives included in the structure of fresh phosphogypsum dissolved in water due to weathering (humidification-drying, freezing-thawing in a water-saturated state), and the calcium hydro-and dihydrogen phosphates ingressed in the lattice underwent complete hydrolysis and disintegration, thereby changing the physicochemical properties of phosphogypsum. The data obtained by the authors on the absence of water-soluble compounds of phosphorus, fluorine in stale phosphogypsum indicate its ecological purity and the possibility of application in housing construction. Having analyzed the data of modern methods of differential scanning calorimetry and scanning electron microscopy, the authors predicted and proved by the energy of dehydration of phosphogypsum dihydrate, lime, sandy loam, the possibility of obtaining non-flammable materials with sufficient strength for wall materials. Understanding the processes occurring in water films (the thickness of the water film, the pressure, the temperature and the pH of the aqueous extract of the mixture, the drying of the materials produced), made it possible to develop a technology for obtaining wall products from lime-sandy phosphogypsum material using typical silicate brick production equipment and vibropresses for key-cog blocks production.

Evaluation of the impact of tromethamine edetate disodium dihydrate on antimicrobial susceptibility of Pseudomonas aeruginosa in biofilm in vitro.

PubMed

Pye, Charlotte C; Singh, Ameet; Weese, J Scott

2014-04-01

Biofilm formation by Pseudomonas aeruginosa has been documented in canine otic isolates. An increase in minimal inhibitory concentration (MIC) for specific antibiotics has been noted for biofilm-embedded bacteria. Tromethamine edetate disodium dihydrate buffered to pH 8 with tromethamine hydrochloride and deionized water (Triz-EDTA(®)) has been documented to potentiate bactericidal activity when used in combination with topical antibiotics, but the impact on biofilm-embedded bacteria is unknown. The objective of this study was to evaluate the impact of Triz-EDTA(®) use on in vitro antimicrobial susceptibility of biofilm-embedded P. aeruginosa. Biofilm formation was documented using a microtitre plate assay. Broth microdilution was used to assess the MIC of neomycin, polymyxin B, enrofloxacin and gentamicin for the biofilm-embedded bacteria. The microtitre plate assay was again used to assess the MIC of neomycin, polymyxin B, enrofloxacin and gentamicin for biofilm-embedded bacteria with added Triz-EDTA(®). Thirty-one isolates from dogs with otitis were tested. Addition of Triz-EDTA(®) significantly reduced MICs for neomycin (P < 0.003) and gentamicin (P < 0.02) but not for polymyxin B (P = 0.3). Enrofloxacin MICs increased in the presence of Triz-EDTA (P < 0.036). Triz-EDTA(®) may be a useful adjunctive treatment for chronic cases of Pseudomonas otitis where biofilms may have developed, if gentamicin or neomycin is to be used as a topical treatment. In vivo study is required to confirm this effect. © 2014 ESVD and ACVD.

Relative hyperoxaluria, crystalluria and haematuria after megadose ingestion of vitamin C.

PubMed

Auer, B L; Auer, D; Rodgers, A L

1998-09-01

Long-term or high-dosage consumption of vitamin C may play a role in calcium oxalate kidney stone formation. The present study was undertaken to determine the biochemical and physicochemical risk factors in a male subject who developed haematuria and calcium oxalate crystalluria after ingestion of large doses of ascorbic acid for 8 consecutive days. Twenty-four-hour urine samples were collected before and during the ascorbic acid ingestion period as well as after the detection of haematuria. A special procedure was implemented for urine collections to allow for oxalate, ascorbate and other urinalysis. Oxalate was determined in the presence of EDTA to prevent in vitro conversion to ascorbic acid, whereas ascorbate itself was determined by manual titration in a redox method using the dye dichlorophenolindophenol. Urinalysis data were used to compute calcium oxalate relative supersaturations and Tiselius risk indices, whereas scanning electron microscopy was used to examine urinary deposits. Oxalate excretion increased by about 350% during ascorbate ingestion before haematuria. Ascorbate concentrations also increased dramatically but appeared to reach a plateau maximum. Increasing calcium excretion was accompanied by decreasing potassium and phosphate values. The calcium oxalate relative supersaturation and Tiselius risk index increased during vitamin C ingestion and large aggregates of calcium oxalate dihydrate crystals were observed by scanning electron microscopy immediately after the detection of haematuria. High percentage metabolic conversion of ascorbate to oxalate in this subject caused relative hyperoxaluria and crystalluria, the latter manifesting itself as haematuria. Clinicians need to be alerted to the potential dangers of large dose ingestion of vitamin C in some individuals.

In vitro study of root fracture treated by CO2 laser and DP-bioactive glass paste.

PubMed

Wang, Yin-Lin; Lee, Bor-Shiunn; Tseng, Ching-Li; Lin, Feng-Huei; Lin, Chun-Pin

2008-01-01

An ideal material has yet to be discovered that can successfully treat vertical root fracture. Therefore, the purpose of this study was to use a continuous-wave CO2 laser of medium-energy density to fuse DP-bioactive glass paste (DPGP) to vertical root fracture. The DP-bioglass powder was based on a Na2O-CaO-SiO2-P2O5 system and it was mixed with phosphoric acid (65% concentration) with a powder/liquid ratio of 2 g/4 mL to form DPGP. The interaction of DPGP and dentin was analyzed by means of X-ray diffractometer (XRD) and differential thermal analysis/thermogravimetric analysis (DTA/TGA). Root fracture line was filled with DPGP followed by CO2 laser irradiation and the result was examined by scanning electron microscopy (SEM). The main crystal phase of DPGP was monocalcium phosphate monohydrate (Ca(H2PO4)2.H2O) and the phase transformed to dicalcium phosphate dihydrate (CaHPO4.2H2O) after mixing DPGP with dentin powder (DPG-D). Additionally, gamma-Ca2P2O7 and beta-Ca2P2O7 were identified when DPG-D was lased by CO2 laser. The reaction temperature was between 500 degrees C and 1100 degrees C. SEM results demonstrated that the fracture line was effectively sealed by DPGP. The chemical reaction of DPGP and dentin indicated that DPGP combined with CO2 laser is a potential regimen for the treatment of vertical root fracture.

Bis(2,3,5,6-tetra-2-pyridyl­pyrazine-κ3 N 2,N 1,N 6)nickel(II) dithio­cyanate dihydrate

PubMed Central

De la Pinta, Noelia; Fidalgo, M. Luz; Ezpeleta, José M.; Cortés, Roberto; Madariaga, Gotzon

2011-01-01

In the title compound, [Ni(C24H16N6)2](NCS)2·2H2O, the central NiII ion is octahedrally coordinated by six N atoms of two tridentate 2,3,5,6-tetra-2-pyridyl­pyrazine ligands (tppz). Two thio­cyanate anions act as counter-ions and two water mol­ecules act as solvation agents. O—H⋯N hydrogen bonds are observed in the crystral structure. PMID:21522540

Tris[4,4′-(ethene-1,2-di­yl)dipyridinium] deca­vanadate dihydrate

PubMed Central

Fernandez de Luis, Roberto; Urtiaga, M. Karmele; Mesa, José Luis; Arriortua, María I.

2010-01-01

The asymmetric unit of the title compound, (C12H12N2)3[V10O28]·2H2O, contains one half of a deca­vanadate anion, one and a half trans-1,2-bis­(4-pyridinio)ethene cations and one water mol­ecule. The V10O28 groups are involved in a three-dimensional hydrogen-bonding network through Ow—H⋯O, N—H⋯O and C—H⋯O inter­actions. PMID:21580261

Targeted Gold Nanoparticle Contrast Agent for Digital Breast Tomosynthesis and Computed Tomography

DTIC Science & Technology

2010-03-01

hearing mantle and magnetic stirrer, and the gold solution was brought to a boil (Figure 1a). Next, 0.93 g of sodium citrate dihydrate...C6H5Na3O7.2H2O ) was dissolved in 45 mL of DI-H2O and added to the boiling gold solution. Upon addition of the sodium citrate, the solution rapidly changed...diatrizoate and related triiodinated benzoates by Trametes versicolor. Appl Environ Microbiol, 1998. 64(8): p. 3114-7. 2. Baselga, J., A.D. Seidman, P.P

Effect of preparation conditions on the nanostructure of hydroxyapatite and brushite phases

NASA Astrophysics Data System (ADS)

Mansour, S. F.; El-dek, S. I.; Ahmed, M. A.; Abd-Elwahab, S. M.; Ahmed, M. K.

2016-10-01

Hydroxyapatite (HAP) and dicalcium phosphate dihydrate (brushite) nanoparticles were prepared by co-precipitation method. The obtained products were characterized by X-ray powder diffraction (XRD), Fourier transformation infra-red spectroscopy (FTIR) and thermo-gravimetric analysis (TGA). Scanning electron microscopy (SEM) and transmission electron microscope (TEM) were used to investigate the morphology of the powdered samples as well as their microstructure, respectively. Brushite samples were obtained in a spherical shape, while hydroxyapatite was formed in a needle and rice shape depending on the pH value.

The effect of hydrodynamic and thermodynamic factors and the addition of citric acid on the precipitation of calcium oxalate dihydrate.

PubMed

Šter, Anamarija; Šafranko, Silvija; Bilić, Katarina; Marković, Berislav; Kralj, Damir

2018-06-01

This paper reports on the investigation of experimental conditions relevant for spontaneous precipitation of significant amount of pure calcium oxalate dihydrate (COD). For this purpose, the hydrodynamic and thermodynamic parameters, such as mode of agitation, temperature, supersaturation and concentration of additives (citrate ions), have been studied. The results show that in the model systems, without the citrate addition and applied mechanical stirring, calcium oxalate monohydrate (COM) was observed as dominant modification after 20 min of aging, while the magnetic stirring resulted in a formation of a mixture of COM and calcium oxalate trihydrate (COT), regardless of the temperature applied. In the mechanically stirred systems, the addition of citrate ions in the range of concentrations, 0.001 mol dm -3  < c i (Na 3 C 6 H 5 O 7 ) < 0.012 mol dm -3 , caused the formation of COM and COD mixture at all temperatures. At the same conditions and in the magnetically stirred systems formation of COD, in a mixture with COT or COM, has been observed. The highest COD content in the mechanically stirred system was obtained at 45 °C and c i (Na 3 C 6 H 5 O 7 ) = 0.001 mol dm -3 (w = 89.5%), while in the magnetically stirred system almost pure COD was obtained at 37 °C and c i (Na 3 C 6 H 5 O 7 ) = 0.008 mol dm -3 (w = 96.5%).

Photoluminescent enhancement of CdSe/Cd(1-x) Zn(x)S quantum dots by hexadecylamine at room temperature.

PubMed

Yang, Jie; Yang, Ping

2012-09-01

CdSe/Cd(1-x) Zn(x)S core/shell quantum dots (QDs) were fabricated in 1-octadecene via a two step synthesis. CdSe cores were first prepared using CdO, trioctylphosphine (TOP) selenium, and stearic acid. Subsquently, a Cd(1-x) Zn(x)S shell coating was carried out using zinc acetate dihydrate, cadmium acetate dihydrate, TOPS, and hexadecylamine (HDA) starting materials in the friendly organic system under relatively low temperature. The absorption and photoluminescence (PL) spectra have a significant red shift after the coverage of Cd(1-x)Zn(x)S shell on CdSe cores. The X-ray diffraction analysis of samples confirmed the formation of core/shell structure. The PL quantum yields (QYs) of CdSe/Cd(1-x)Zn(x)S QDs were improved gradually with time at room temperature. This is ascribed to the surface passivation of HDA to the QDs during store. This phenomenon was confirmed by the Fourier transform infrared spectrum of samples. Namely, HDA does not capped on the surface of as-prepared QDs, in which a low PL QYs was observed (less than 10%). Being storing for certain time, HDA attached to the surface of the QDs, in which the PL QYs increased (up to 31%) and the full width at half maximum of PL spectra decreased. Moreover, the fluorescence decay curve of the core/shell QDs is closer to a biexponential decay profile and has a longer average PL lifetime. The variation of average PL lifetime also indicated the influence of HDA during store.

Prevalence of asymptomatic chondrocalcinosis in the pelvis.

PubMed

Stensby, James Derek; Lawrence, David A; Patrie, James T; Gaskin, Cree M

2016-07-01

To determine trends in incidentally detected age- and gender-associated chondrocalcinosis on pelvic CT. Twenty patients of each gender at the center of each decade of life who underwent a CT scan of the pelvis performed 2009-2013 were identified and selected for a total of 400 pelvic CTs. Images were reviewed independently by two radiologists for the presence or absence of chondrocalcinosis within the pelvis. Patients with hip or low back pain, known CPPD arthropathy or any known predisposing condition, prior hip arthroplasty, or articular fracture were excluded. Logistic regression was used to predict the presence/absence of chondrocalcinosis as a function of patient age and gender. The presence/absence of chondrocalcinosis was found to be associated with patient age (p = 0.016) but not patient gender (p = 0.929). In the pelvis, chondrocalcinosis was most frequently identified at the pubic symphysis. Incidental chondrocalcinosis was not identified in any patients under 50 years of age. Chondrocalcinosis increased in frequency from 12.5 at 55 years of age to 27.5 % of patients 95 years of age. Chondrocalcinosis is common and more prevalent in late adulthood, occurs without a gender predilection, and is infrequently identified in patients younger than 50 years of age.

Trichomes of Tobacco Excrete Zinc as Zinc-Substituted Calcium Carbonate and Other Zinc-Containing Compounds1[W

PubMed Central

Sarret, Géraldine; Harada, Emiko; Choi, Yong-Eui; Isaure, Marie-Pierre; Geoffroy, Nicolas; Fakra, Sirine; Marcus, Matthew A.; Birschwilks, Mandy; Clemens, Stephan; Manceau, Alain

2006-01-01

Tobacco (Nicotiana tabacum L. cv Xanthi) plants were exposed to toxic levels of zinc (Zn). Zn exposure resulted in toxicity signs in plants, and these damages were partly reduced by a calcium (Ca) supplement. Confocal imaging of intracellular Zn using Zinquin showed that Zn was preferentially accumulated in trichomes. Exposure to Zn and Zn + Ca increased the trichome density and induced the production of Ca/Zn mineral grains on the head cells of trichomes. These grains were aggregates of submicrometer-sized crystals and poorly crystalline material and contained Ca as major element, along with subordinate amounts of Zn, manganese, potassium, chlorine, phosphorus, silicon, and magnesium. Micro x-ray diffraction revealed that the large majority of the grains were composed essentially of metal-substituted calcite (CaCO3). CaCO3 polymorphs (aragonite and vaterite) and CaC2O4 (Ca oxalate) mono- and dihydrate also were identified, either as an admixture to calcite or in separate grains. Some grains did not diffract, although they contained Ca, suggesting the presence of amorphous form of Ca. The presence of Zn-substituted calcite was confirmed by Zn K-edge micro-extended x-ray absorption fine structure spectroscopy. Zn bound to organic compounds and Zn-containing silica and phosphate were also identified by this technique. The proportion of Zn-substituted calcite relative to the other species increased with Ca exposure. The production of Zn-containing biogenic calcite and other Zn compounds through the trichomes is a novel mechanism involved in Zn detoxification. This study illustrates the potential of laterally resolved x-ray synchrotron radiation techniques to study biomineralization and metal homeostasis processes in plants. PMID:16731580

To evaluate the effect of various magnesium stearate polymorphs using powder rheology and thermal analysis.

PubMed

Okoye, Patrick; Wu, Stephen H; Dave, Rutesh H

2012-12-01

The effects of magnesium stearate (MgSt) polymorphs-anhydrate (MgSt-A), monohydrate (MgSt-M), and dihydrate (MgSt-D)-on rheological properties of powders were evaluated using techniques such as atomic analysis and powder rheometry. Additional evaluation was conducted using thermal analysis, micromeritics, and tableting forces. In this study, binary ratios of neat MgSt polymorphs were employed as lubricants in powder blends containing acetaminophen (APAP), microcrystalline cellulose (MCC), and lactose monohydrate (LAC-M). Powder rheometry was studied using permeability, basic flow energy (BFE), density, and porosity analysis. Thermal conductivity and differential scanning calorimetric analysis of MgSt polymorphs were employed to elucidate MgSt effect on powder blends. The impact of MgSt polymorphs on compaction characteristics were analyzed via tablet compression forces. Finally, the distribution of atomized magnesium (Mg) ions as a function of intensity was evaluated using laser-induced breakdown spectroscopy (LIBS) on tablets. The results from LIBS analysis indicated the dependency of the MgSt polymorphic forms on the atomized Mg ion intensity, with higher Mg ion intensity suggesting higher lubricity index (i.e. greater propensity to over-lubricate). The results from lubricity index suggested the tendency of blends to over-lubricate based on the MgSt polymorphic forms. Finally, tableting forces suggested that MgSt-D and MgSt-A offered processing benefits such as lower ejection and compression forces, and that MgSt-M showed the most stable compression force in single or combined polymorphic ratios. These results suggested that the initial moisture content, crystal arrangement, intra- and inter-molecular packing of the polymorphs defined their effects on the rheology of lubricated powders.

Two novel mixed-ligand complexes containing organosulfonate ligands.

PubMed

Li, Mingtian; Huang, Jun; Zhou, Xuan; Fang, Hua; Ding, Liyun

2008-07-01

The structures reported herein, viz. bis(4-aminonaphthalene-1-sulfonato-kappaO)bis(4,5-diazafluoren-9-one-kappa(2)N,N')copper(II), [Cu(C(10)H(8)NO(3)S)(2)(C(11)H(6)N(2)O)(2)], (I), and poly[[[diaquacadmium(II)]-bis(mu-4-aminonaphthalene-1-sulfonato)-kappa(2)O:N;kappa(2)N:O] dihydrate], {[Cd(C(10)H(8)NO(3)S)(2)(H(2)O)(2)].2H(2)O}(n), (II), are rare examples of sulfonate-containing complexes where the anion does not fulfill a passive charge-balancing role, but takes an active part in coordination as a monodentate and/or bridging ligand. Monomeric complex (I) possesses a crystallographic inversion center at the Cu(II) atom, and the asymmetric unit contains one-half of a Cu atom, one complete 4-aminonaphthalene-1-sulfonate (ans) ligand and one 4,5-diazafluoren-9-one (DAFO) ligand. The Cu(II) atom has an elongated distorted octahedral coordination geometry formed by two O atoms from two monodentate ans ligands and by four N atoms from two DAFO molecules. Complex (II) is polymeric and its crystal structure is built up by one-dimensional chains and solvent water molecules. Here also the cation (a Cd(II) atom) lies on a crystallographic inversion center and adopts a slightly distorted octahedral geometry. Each ans anion serves as a bridging ligand linking two Cd(II) atoms into one-dimensional infinite chains along the [010] direction, with each Cd(II) center coordinated by four ans ligands via O and N atoms and by two aqua ligands. In both structures, there are significant pi-pi stacking interactions between adjacent ligands and hydrogen bonds contribute to the formation of two- and three-dimensional networks.

1,4-Bis(4H-1,2,4-triazol-4-yl)benzene dihydrate

PubMed Central

Wang, Xiu-Guang; Li, Jian-Hui; Ding, Bin; Du, Gui-Xiang

2012-01-01

The asymmetric unit of the title compound, C10H8N6·2H2O, comprises half the organic species, the mol­ecule being completed by inversion symmetry, and one water mol­ecule. The dihedral angle between the 1,2,4-triazole ring and the central benzene ring is 32.2 (2)°. The water mol­ecules form O—H⋯N hydrogen bonds with N-atom acceptors of the triazole rings. C—H⋯N hydrogen bonds are also observed, giving a three-dimensional framework. PMID:22904851

Trajectory Studies of Large HNO3-Containing PSC Particles in the Arctic: Evidence for the Role of NAT

NASA Technical Reports Server (NTRS)

McKinney, K. A.; Wennberg, P. O.; Dhaniyala, S.; Fahey, D. W.; Northway, M. J.; Kuenzi, K. F.; Kleinboehl, A.; Sinnhuber, M.; Kuellmann, H.; Bremer, H.;

Regenerable sorbents for CO.sub.2 capture from moderate and high temperature gas streams

DOEpatents

Siriwardane, Ranjani V [Morgantown, WV

2008-01-01

A process for making a granular sorbent to capture carbon dioxide from gas streams comprising homogeneously mixing an alkali metal oxide, alkali metal hydroxide, alkaline earth metal oxide, alkaline earth metal hydroxide, alkali titanate, alkali zirconate, alkali silicate and combinations thereof with a binder selected from the group consisting of sodium ortho silicate, calcium sulfate dihydrate (CaSO.sub.4.2H.sub.2O), alkali silicates, calcium aluminate, bentonite, inorganic clays and organic clays and combinations thereof and water; drying the mixture and placing the sorbent in a container permeable to a gas stream.

Hexaaqua­cobalt(II) bis­[4-(pyridin-2-yl­meth­oxy)benzoate] dihydrate

PubMed Central

Zhang, Li-Wei; Gao, Shan; Ng, Seik Weng

2011-01-01

The CoII atom in the title salt, [Co(H2O)6](C13H10NO3)2·2H2O, lies on a center of inversion in an octa­hedron of water mol­ecules. The cations, anions and uncoordinated water mol­ecules are linked by O—H⋯O and O—H⋯N hydrogen bonds into a three-dimensional network. The anion is essentially planar, with an r.m.s. deviation of all non-H atoms of 0.066 Å. PMID:22219767

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bohner, Bíborka; Endrődi, Balázs; Tóth, Ágota, E-mail: atoth@chem.u-szeged.hu

The precipitation reaction of calcium oxalate is studied experimentally in the presence of spatial gradients by controlled flow of calcium into oxalate solution. The density difference between the reactants leads to strong convection in the form of a gravity current that drives the spatiotemporal pattern formation. The phase diagram of the system is constructed, the evolving precipitate patterns are analyzed and quantitatively characterized by their diameters and the average height of the gravity flow. The compact structures of calcium oxalate monohydrate produced at low flow rates are replaced by the thermodynamically unstable calcium oxalate dihydrate favored in the presence ofmore » a strong gravity current.« less

Crystal chemistry of thorium nitrates and chromates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sigmon, Ginger E.; Burns, Peter C., E-mail: pburns@nd.ed

2010-07-15

The structures and infrared spectra of six novel thorium compounds are reported. Th(NO{sub 3}){sub 2}(OH){sub 2}(H{sub 2}O){sub 2} (1) crystallizes in space group C2/c, a=14.050(1), b=8.992(7), c=5.954(5) A, {beta}=101.014(2){sup o}. K{sub 2}Th(NO{sub 3}){sub 6} (2), P-3, a=13.606(1), c=6.641(6) A. (C{sub 12}H{sub 28}N){sub 2}Th(NO{sub 3}){sub 6} (3), P2{sub 1}/c, a=14.643(4), b=15.772(5), c=22.316(5) A, {beta}=131.01(1){sup o}. KTh(NO{sub 3}){sub 5}(H{sub 2}O){sub 2} (4), P2{sub 1}/c, a=10.070(8), b=12.731(9), c=13.231(8) A, {beta}=128.647(4){sup o}. Th(CrO{sub 4}){sub 2}(H{sub 2}O){sub 2} (5), P2{sub 1}/n, a=12.731(1), b=9.469(8), c=12.972(1) A, {beta}=91.793(2){sup o}. K{sub 2}Th{sub 3}(CrO{sub 4}){sub 7}(H{sub 2}O){sub 10} (6), Ama2, a=19.302(8), b=15.580(6), c=11.318(6) A. The coordination polyhedra about Thmore » in these structures are diverse. Th is coordinated by 9 O atoms in 5 and 6, seven of which are from monodentate (CrO{sub 4}) tetrahedra and two are (H{sub 2}O). The Th in compound 1 is coordinated by ten O atoms, four of which are O atoms of two bidentate (NO{sub 3}) triangles and six of which are (OH) and (H{sub 2}O). In compounds 2, 3 and 4 the Th is coordinate by 12 O atoms. In 2 and 3 there are six bidentate (NO{sub 3}) triangles, and in 4 ten of the O atoms are part of five bidentate (NO{sub 3}) triangles and the others are (H{sub 2}O) groups. The structural units of these compounds consist of a chain of thorium and nitrate polyhedra (1), isolated thorium hexanitrate clusters (2, 3), an isolated thorium pentanitrate dihydrate cluster (4), and a sheet (6) and framework (5) of thorium and chromate polyhedra. These structures illustrate the complexity inherent in the crystal chemistry of Th. - Graphical Abstract: The structures and infrared spectra of four new Th nitrates and two Th chromates are reported. The coordination numbers of the Th cations range from nine to 12 in these compounds. Structural units consist of isolated clusters, chains, sheets and frameworks.« less

Investigation of drug-excipient compatibility using rheological and thermal tools

NASA Astrophysics Data System (ADS)

Trivedi, Maitri R.

HYPOTHESIS: We plan to investigate a different approach to evaluate drug-excipient physical compatibility using rheological and thermal tools as opposed to commonly used chemical techniques in pharmaceutical industry. This approach offers practical solutions to routinely associated problems arising with API's and commonly used hydrates forms of excipients. ABSTRACT: Drug-Excipient compatibility studies are an important aspect of pre-formulation and formulation development in pharmaceutical research and development. Various approaches have been used in pharmaceutical industry including use of thermal analysis and quantitative assessment of drug-excipient mixtures after keeping the samples under stress environment depending upon the type of formulation. In an attempt to provide better understanding of such compatibility aspect of excipients with different properties of API, various rheological and thermal studies were conducted on binary mixtures of excipients which exist in different hydrates. Dibasic Calcium Phosphate (DCP, anhydrous and dihydrate forms) and Lactose (Lac, anhydrous and monohydrate) were selected with cohesive API's (Acetaminophen and Aspirin). Binary mixtures of DCP and Lac were prepared by addition of 0% w/w to 50% w/w of the API into each powder blend. Rheological and thermal aspects were considered using different approaches such as powder rheometer, rotational shear cell and traditional rheometery approaches like angle of repose (AOR), hausner's ratio (HR) and cares index (CI). Thermal analysis was conducted using modulated differential scanning calorimetry (MDSC) and thermal effusivity. The data suggested that the powder rheometer showed distinctive understanding in the flowability behavior of binary mixtures with addition of increasing proportion of API's than traditional approaches. Thermal approaches revealed the potential interaction of water of crystallization DCP-D with the API (APAP) while such interactions were absent in DCP-A, while in case of Lac-M and Lac-A, interaction with water of crystallization were not present. Binary mixtures prepared with DCP-D were better flowable while blends with DCP-A were better in stability (physical), compressibility and permeability. Similarly binary mixtures prepared with Lac-M were better flowable and stable in physical compatibility as compared to Lac-A. Lac-A were better in compressibility and permeability. Second part of these research included understanding the powder behavior from wet granulation point of view. Wet granulation includes the formation of agglomerates with powders to form granules in order to have better flowability, content uniformity and compressibility of granular mass. End point determination of powders involving change in powder energies and compressibility, permeability along with thermal analyses were conducted. The effects of water of crystallization on end point determination was studied and based on which overall effects on drug-excipient compatibility using different hydrate forms of excipients were evaluated.

EPR, ENDOR, and DFT study of free radicals in L-lysine·HCl·2H2O single crystals X-irradiated at 298 K.

PubMed

Zhou, Yiying; Nelson, William H

2011-10-27

With K-band EPR (Electron Paramagnetic Resonance), ENDOR (Electron-Nuclear DOuble Resonance), and EIE (ENDOR-induced EPR) techniques, three free radicals (RI-RIII) in L-lysine hydrochloride dihydrate single crystals X-irradiated at 298 K were detected at 298 K, and six radicals (R1, R1', R2-R5) were detected if the temperature was lowered to 66 K from 298 K. R1 and RI dominated the central portion of the EPR at 66 and 298 K, respectively, and were identified as main chain deamination radicals, (-)OOCĊH(CH(2))(4)(NH(3))(+). R1' was identified as a main chain deamination radical with the different configuration from R1 at 66 K, and it probably formed during cooling the temperature from 298 to 66 K. The configurations of R1, R1', and RI were analyzed with their coupling tensors. R2 and R3 each contain one α- and four β-proton couplings and have very similar EIEs at three crystallographic axes. The two-layer ONIOM calculations (at B3LYP/6-31G(d,p):PM3) support that R2 and R3 are from different radicals: dehydrogenation at C4, (-)OOCCH(NH(3))(+)CH(2)ĊH(CH(2))(2)(NH(3))(+), and dehydrogenation at C5, (-)OOCCH(NH(3))(+)(CH(2))(2)ĊHCH(2)(NH(3))(+), respectively. The comparisons of the coupling tensors indicated that R2 (66 K) is the same radical as RII (298 K), and R3 is the same as RIII. Thus, RII and RIII also are the radicals of C4 and C5 dehydrogenation. R4 and R5 are minority radicals and were observed only when temperature was lowered to 66 K. R4 and R5 were only tentatively assigned as the side chain deamination radical, (-)OOCCH (NH(3))(+)(CH(2))(3)ĊH(2), and the radical dehydrogenation at C3, (-)OOCCH(NH(3))(+)ĊH(CH(2))(3)(NH(3))(+), respectively, although the evidence was indirect. From simulation of the EPR (B//a, 66 K), the concentrations of R1, R1', and R2-R5 were estimated as: R1, 50%; R1', 11%; R2, 14%; R3, 16%; R4, 6%; R5, 3%.

Stone clearance after extracorporeal shockwave lithotripsy in patients with solitary pure calcium oxalate stones smaller than 1.0 cm in the proximal ureter, with special reference to monohydrate and dihydrate content.

PubMed

Ichiyanagi, Osamu; Nagaoka, Akira; Izumi, Takuji; Kawamura, Yuko; Tsukigi, Masaaki; Ishii, Tatsuya; Ohji, Hiroshi; Kato, Tomoyuki; Tomita, Yoshihiko

2013-04-01

The aim of this study was to assess stone-free rates following extracorporeal shockwave lithotripsy (ESWL) of pure calcium oxalate (CaOx) stones in the proximal ureter. The investigators retrospectively examined 53 patients with 5-10 mm pure CaOx stones in the proximal ureter from the medical archives of 593 consecutive patients treated with ESWL. The compositions of calcium oxalate monohydrate (COM) and dihydrate (COD) in a given stone were determined by infrared spectrometry. Stone size, attenuation number and stone-to-skin distance (SSD) were measured using plain radiography and computed tomography (CT). ESWL success was evaluated by stone-free status after the first single session. On average, calculi were 8.0 × 5.3 mm in size, with an SSD of 11.0 cm. The mean CT attenuation value was 740.1 HU. Attenuation numbers correlated significantly with stone diameter (r = 0.49), but had no correlation with the stone content of COM or COD. A negative correlation was observed between COM and COD content (r = -0.925). With regard to patients' physical characteristics and COM and COD content, no differences were found between study subgroups with stone-free and residual status (n = 38 and 15, respectively). There were also no differences in clinical features between patient subgroups with COM- or COD-predominant stones (n = 22 and 31, respectively). The findings indicated that the differences in COM and COD content of CaOx stones had no impact on stone clearance after ESWL and that a favorable stone-free rate of the stones treated with ESWL may be achieved independently of CaOx hydration.

Immunotoxic effects of sodium tungstate dihydrate on female B6C3F1/N mice when administered in drinking water.

PubMed

Frawley, Rachel P; Smith, Matthew J; White, Kimber L; Elmore, Susan A; Herbert, Ron; Moore, Rebecca; Staska, Lauren M; Behl, Mamta; Hooth, Michelle J; Kissling, Grace E; Germolec, Dori R

2016-09-01

Tungsten is a naturally occurring, high-tensile strength element that has been used in a number of consumer products. Tungsten has been detected in soil, waterways, groundwater, and human tissue and body fluids. Elevated levels of tungsten in urine were reported for populations exposed to tungstate in drinking water in areas where natural tungsten formations were prevalent. Published reports indicated that sodium tungstate may modulate hematopoiesis, immune cell populations, and immune responses in rodent models. The objective of this study was to assess potential immunotoxicity of sodium tungstate dihydrate (STD), a drinking water contaminant. Female B6C3F1/N mice received 0-2000 mg STD/L in their drinking water for 28 d, and were evaluated for effects on immune cell populations in spleen and bone marrow, and humoral-mediated, cell-mediated, and innate immunity. Three different parameters of cell-mediated immunity were similarly affected at 1000 mg STD/L. T-cell proliferative responses against allogeneic leukocytes and anti-CD3 were decreased 32%, and 21%, respectively. Cytotoxic T-lymphocyte activity was decreased at all effector:target cell ratios examined. At 2000 mg STD/L, the absolute numbers of CD3(+) T-cell progenitor cells in bone marrow were increased 86%, but the alterations in B-lymphocyte and other progenitor cells were not significant. There were no effects on bone marrow DNA synthesis or colony forming capabilities. STD-induced effects on humoral-mediated immunity, innate immunity, and splenocyte sub-populations were limited. Enhanced histopathology did not detect treatment-related lesions in any of the immune tissues. These data suggest exposure to STD in drinking water may adversely affect cell-mediated immunity.

Stone size limits the use of Hounsfield units for prediction of calcium oxalate stone composition.

PubMed

Stewart, Gregory; Johnson, Lewis; Ganesh, Halemane; Davenport, Daniel; Smelser, Woodson; Crispen, Paul; Venkatesh, Ramakrishna

2015-02-01

To evaluate the role of stone size in predicting urinary calculus composition using Hounsfield units on noncontrasted computed tomography (CT) scan. A retrospective review was performed for all patients who underwent ureteroscopy or percutaneous nephrolithotomy during a 1-year period, had a stone analysis performed, and had CT imaging available for review. All CT scans were reviewed by a board-certified radiologist. Variables evaluated included age, sex, body mass index, stone size, stone location, Hounsfield units (HUs), and stone composition. We identified a total of 91 patients (41 men and 50 women) with CT imaging and stone analysis available for review. Stone analysis showed 41 calcium oxalate monohydrate (CaOxMH), 13 calcium oxalate dihydrate, 29 calcium phosphate, 5 uric acid, 2 struvite, and 1 cystine stone. Average age was 46 years, and average body mass index was 32 kg/m2. Measured HUs varied significantly with size for CaOxMH and calcium oxalate dihydrate stones (P values <.05), but not for calcium phosphate stones (P = .126). Using a CaOxMH identification value of 700-1000 HUs, 28 of 41 stone compositions (68%) would not have been correctly identified, including all 10 (100%) small (<5 mm) stones, 13 of 22 (59%) medium (5-10 mm) stones, and 5 of 9 large (>10 mm) stones (55%). For calcium stones, the ability of CT HUs to predict stone composition was limited, likely due to the mixed stone composition. Within a cohort of CaOxMH stone formers, measured HUs varied linearly with stone size. All stones <5 mm were below thresholds for CaOxMH composition. Copyright © 2015 Elsevier Inc. All rights reserved.

Immunotoxic Effects of Sodium Tungstate Dihydrate on Female B6C3F1/N Mice When Administered in Drinking Water

PubMed Central

Frawley, Rachel P.; Smith, Matthew J.; White, Kimber L; Elmore, Susan; Herbert, Ron; Moore, Rebecca; Staska, Lauren M.; Behl, Mamta; Hooth, Michelle J.; Kissling, Grace E.; Germolec, Dori R.

2018-01-01

Tungsten is a naturally occurring, high tensile strength element that has been used in a number of consumer products. Tungsten has been detected in soil, waterways, groundwater, and human tissue and body fluids. Elevated levels of tungsten in urine were reported for populations exposed to tungstate in drinking water in areas where natural tungsten formations were prevalent. Published reports indicated that sodium tungstate may modulate hematopoiesis, immune cell populations, and immune responses in rodent models. The objective of this study was to assess potential immunotoxicity of sodium tungstate dihydrate (STD), a drinking water contaminant. Female B6C3F1/N mice received 0–2000 mg STD/L in their drinking water for 28 days, and were evaluated for effects on immune cell populations in spleen and bone marrow, and humoral-mediated, cell-mediated, and innate immunity. Three different parameters of cell-mediated immunity were similarly affected at 1000 mg STD/L. T-cell proliferative responses against allogeneic leukocytes and anti-CD3 were decreased 32%, and 21%, respectively. Cytotoxic T-lymphocyte activity was decreased at all effector:target cell ratios examined. At 2000 mg STD/L, the absolute numbers of CD3+ T-cell progenitor cells in bone marrow were increased 86%, but the alterations in B-lymphocyte and other progenitor cells were not significant. There were no effects on bone marrow DNA synthesis or colony forming capabilities. STD-induced effects on humoral-mediated immunity, innate immunity, and splenocyte sub-populations were limited. Enhanced histopathology did not detect treatment-related lesions in any of the immune tissues. These data suggest exposure to STD in drinking water may adversely effect cell-mediated immunity. PMID:27223060

Computed phase diagrams for the system: Sodium hydroxide-uric acid-hydrochloric acid-water

NASA Astrophysics Data System (ADS)

Brown, W. E.; Gregory, T. M.; Füredi-Milhofer, H.

1987-07-01

Renal stone formation is made complex by the variety of solid phases that are formed, by the number of components in the aqueous phase, and by the multiplicity of ionic dissociation and association processes that are involved. In the present work we apply phase diagrams calculated by the use of equilibrium constants from the ternary system sodium hydroxide-uric acid-water to simplify and make more rigorous the understanding of the factors governing dissolution and precipitation of uric acid (anhydrous and dihydrate) and sodium urate monohydrate. The system is then examined in terms of four components. Finally, procedures are described for fluids containing more than four components. The isotherms, singular points, and fields of supersaturation and undersaturation are shown in various forms of phase diagrams. This system has two notable features: (1) in the coordinates -log[H 2U] versus -log[NaOH], the solubility isotherms for anhydrous uric acid and uric acid dihydrate approximate straight lines with slopes equal to +1 over a wide range of concentrations. As a result, substantial quantities of sodium acid urate monohydrate can precipitate from solution or dissolve without changing the degree of saturation of uric acid significantly. (2) The solubility isotherm for NaHU·H 2O has a deltoid shape with the low-pH branch having a slope of infinity. As a result of the vertical slope of this isotherm, substantial quantities of uric acid can dissolve or precipitate without changing the degree of saturation of sodium acid urate monohydrate significantly. The H 2U-NaOH singular point has a pH of 6.87 at 310 K in the ternary system.

Tautomeric transformation of temozolomide, their proton affinities and chemical reactivities: A theoretical approach.

PubMed

Sang-Aroon, Wichien; Ruangpornvisuti, Vithaya; Amornkitbamrung, Vittaya

2016-05-01

The gas-phase geometry optimizations of bare, mono- and dihydrated complexes of temozolomide isomers were carried out using density functional calculation at the M06-2X/6-31+G(d,p) level of the theory. The structures and protonation energies of protonated species of temozolomide are reported. Chemical indices of all isomers and protonated species are also reported. Energies, thermodynamic quantities, rate constants and equilibrium constants of tautomeric and rotameric transformations of all isomers I1↔TZM↔HIa↔HIb↔I2↔I3 in bare and hydrated systems were obtained. Copyright © 2016 Elsevier Inc. All rights reserved.

Radiolysis of lignin: Prospective mechanism of high-temperature decomposition

NASA Astrophysics Data System (ADS)

Ponomarev, A. V.

2017-12-01

The range of the radiation-thermal processes resulting in conversion of lignin into monomeric phenols is considered. Statistically the most probable places of macromolecule ionization are aromatic units. Release of phenolic products from a lignin macromolecule is the multistage process beginning via fragmentation of primary cation-radicals. Reactions of electrons and small radicals with macromolecules, also as degradation of cation-radicals, result in formation of phenoxyl radicals. Macroradicals possess lower heat stability in comparison with macromolecules. Thermal decomposition of macroradicals leads to release of monohydric and dihydric phenols. The probability of benzenediols formation increases in the presence of alkanes. As noted, partial transformation of lignin into charcoal is inevitable.

Zinc oxide films chemically grown onto rigid and flexible substrates for TFT applications

NASA Astrophysics Data System (ADS)

Suchea, M.; Kornilios, N.; Koudoumas, E.

2010-10-01

This contribution presents some preliminary results regarding the use of a chemical route for the growth of good quality ZnO thin films that can be used for the fabrication of thin film transistors (TFTs). The films were grown at rather low temperature (60 °C) on glass and PET substrates using non-aqueous (zinc acetate dihydrate in methanol) precursor solution and their surface morphology, crystalline structure, optical transmittance and electrical characteristics were studied. The study indicated that good quality films with desirable ZnO structure onto rigid and flexible substrates can be obtained, using a simple, cheap, low temperature chemical growth method.

Flow-driven pattern formation in the calcium-oxalate system.

PubMed

Bohner, Bíborka; Endrődi, Balázs; Horváth, Dezső; Tóth, Ágota

2016-04-28

The precipitation reaction of calcium oxalate is studied experimentally in the presence of spatial gradients by controlled flow of calcium into oxalate solution. The density difference between the reactants leads to strong convection in the form of a gravity current that drives the spatiotemporal pattern formation. The phase diagram of the system is constructed, the evolving precipitate patterns are analyzed and quantitatively characterized by their diameters and the average height of the gravity flow. The compact structures of calcium oxalate monohydrate produced at low flow rates are replaced by the thermodynamically unstable calcium oxalate dihydrate favored in the presence of a strong gravity current.

Mössbauer study on the thermal decomposition of potassium tris (oxalato) ferrate(III) trihydrate and bis (oxalato) ferrate(II) dihydrate

NASA Astrophysics Data System (ADS)

Ladriere, J.

1992-04-01

The thermal decompositions of K3Fe(ox)3 3 H2O and K2Fe(ox)2 2 H2O in nitrogen have been studied using Mössbauer spectroscopy, X-ray diffraction and thermal analysis methods in order to determine the nature of the solid residues obtained after each stage of decomposition. Particularly, after dehydration at 113°C, the ferric complex is reduced into a ferrous compound, with a quadrupole splitting of 3.89 mm/s, which corresponds to the anhydrous form of K2Fe(ox)2 2 H2O.

Determining the morphology of polystyrene-block-poly(2-vinylpyridine) micellar reactors for ZnO nanoparticle synthesis.

PubMed

El-Atwani, Osman; El-Atwani, Osman C; Aytun, Taner; Mutaf, Omer Faruk; Srot, Vesna; van Aken, Peter A; Ow-Yang, Cleva W

2010-05-18

We report the use of reverse PS-b-P2VP diblock copolymer micelles as true nanoscale-sized reactor vessels to synthesize ZnO nanoparticles. The reverse micelles were formed in toluene and then sequentially loaded with zinc acetate dihydrate and tetramethylammonium hydroxide reactants. Moreover, high spatial resolution Z-contrast imaging and EDX spectroscopy techniques were used to confirm the segregation of the Zn cation to the core of the loaded micelles. Determining the chemical distribution with high nanoscale spatial resolution is shown to complement the less direct characterization by AFM, DLS and FTIR, thus demonstrating broader implications for the characterization of hybrid nanocomposite systems.

Effect of surface modification on hydration kinetics of carbamazepine anhydrate using isothermal microcalorimetry.

PubMed

Otsuka, Makoto; Ishii, Mika; Matsuda, Yoshihisa

2003-01-01

The purpose of this research was to improve the stability of carbamazepine (CBZ) bulk powder under high humidity by surface modification. The surface-modified anhydrates of CBZ were obtained in a specially designed surface modification apparatus at 60 degrees C via the adsorption of n-butanol, and powder x-ray diffraction, Fourier-Transformed Infrared spectra, and differential scanning calorimetry were used to determine the crystalline characteristics of the samples. The hydration process of intact and surface-modified CBZ anhydrate at 97% relative humidity (RH) and 40 +/-C 1 degrees C was automatically monitored by using isothermal microcalorimetry (IMC). The dissolution test for surface-modified samples (20 mg) was performed in 900 mL of distilled water at 37 +/-C 0.5 degrees C with stirring by a paddle at 100 rpm as in the Japanese Pharmacopoeia XIII. The heat flow profiles of hydration of intact and surface-modified CBZ anhydrates at 97% RH by using IMC profiles showed a maximum peak at around 10 hours and 45 hours after 0 and 10 hours of induction, respectively. The result indicated that hydration of CBZ anhydrate was completely inhibited at the initial stage by surface modification of n-butanol and thereafter transformed into dihydrate. The hydration of surface-modified samples followed a 2-dimensional phase boundary process with an induction period (IP). The IP of intact and surface-modified samples decreased with increase of the reaction temperature, and the hydration rate constant (k) increased with increase of the temperature. The crystal growth rate constants of nuclei of the intact sample were significantly larger than the surface-modified sample's at each temperature. The activation energy (E) of nuclei formation and crystal growth process for hydration of surface-modified CBZ anhydrate were evaluated to be 20.1 and 32.5 kJ/mol, respectively, from Arrhenius plots, but the Es of intact anhydrate were 56.3 and 26.8 kJ/mol, respectively. The dissolution profiles showed that the surface-modified sample dissolved faster than the intact sample at the initial stage. The dissolution kinetics were analyzed based on the Hixon-Crowell equation, and the dissolution rate constants for intact and surface-modified anhydrates were found to be 0.0102 +/-C 0.008 mg(1/3) x min(-1) and 0.1442 +/-C 0.0482 mg(1/3) x min(-1). The surface-modified anhydrate powders were more stable than the nonmodified samples under high humidity and showed resistance against moisture. However, surface modification induced rapid dissolution in water compared to the control.

Formation of liquid water at low temperatures via the deliquescence of calcium chloride: Implications for Antarctica and Mars

NASA Astrophysics Data System (ADS)

Gough, R. V.; Chevrier, V. F.; Tolbert, M. A.

2016-10-01

There is significant interest in the potential existence of even small amounts of liquid brine on current Mars. It has been proposed that aqueous solutions could form on Mars via the deliquescence of hygroscopic salts in contact with atmospheric water vapor, and these hygroscopic salts have recently been detected in recurring slope linae (RSL). While past work has largely focused on perchlorate species, another Mars-relevant salt that has a low eutectic temperature and may be deliquescent is calcium chloride, CaCl2. This salt may be linked to RSL formation on Mars, and deliquescence of CaCl2 is also known to be responsible for the only terrestrial RSL analog features known thus far: water tracks in the McMurdo Dry Valleys. Here we use Raman microscopy to monitor the low-temperature (223-273 K) deliquescence (solid to aqueous phase transition) and efflorescence (aqueous to solid phase transition) of two hydration states of CaCl2, the dihydrate and the hexahydrate. We find the deliquescence relative humidity (DRH) decreases with decreasing hydration state and with increasing temperature. Average DRH values over the temperature range studied are 15.8±3.5% RH for the dihydrate and 63.3±12.5% RH for the hexahydrate, making this salt at least as deliquescent as many perchlorate salts. A remarkable property of CaCl2 is its ability to persist as metastable, supersaturated brine. Once an aqueous solution was formed, efflorescence (recrystallization) of the liquid did not occur until single-digit RH values were reached (3.9±2.4% RH on average). We show that temperature and relative humidity conditions in the martian subsurface are sufficient to allow deliquescence of CaCl2, and the resulting brines may persist for over half of a martian sol. Therefore, this salt could play a role in RSL formation, the martian water cycle, and have implications for the potential habitability of Mars.

The Effect of Stone Composition on the Efficacy of Retrograde Intrarenal Surgery: Kidney Stones 1 - 3 cm in Diameter.

PubMed

Xue, Yuquan; Zhang, Peng; Yang, Xiaojie; Chong, Tie

2015-05-01

The goal of this study was to analyze the effect of stone composition on the efficacy of retrograde intrarenal surgery (RIRS) with kidney stones of 1-3 cm, 1-2 cm, and 2-3 cm in diameter. We undertook a retrospective analysis of 74 patients with kidney stones who underwent RIRS. The patients were divided into two groups based on stone composition: Group I (n=47) (calcium oxalate monohydrate and calcium phosphate) was the hard to fragment stone group and group II (n=27) (calcium oxalate dihydrate, magnesium ammonium phosphate, and uric acid) was the easy to fragment stone group. Forty-six patients with kidney stones 1 to 2 cm in diameter were divided into group A (n=30) (smaller than 20 mm, hard to fragment stones) and group B (n=16) (smaller than 20 mm, easy to fragment stones). Twenty-eight patients with stones 2 to 3 cm in diameter were divided into group C (n=17) (larger than 20 mm, hard to fragment stones) and group D (n=11) (larger than 20 mm, easy-to-crush stones). The stone clearance rates of group I and group II were 66.0% and 88.9%, respectively (P<0.05). The stone clearance rates of group A and group B were 73.3% and 100% (P<0.05). The stone clearance rates of group C and group D were 52.9% and 72.7%, respectively. Stone composition has a significant impact on the efficacy of RIRS in the management of 1 to 3 cm kidney stones. For 2-3 cm calcium oxalate dihydrate stones, uric acid stones, and magnesium ammonium phosphate stones, the outcome of RIRS treatment was relatively good, and RIRS is recommended.

Chemical interaction of glycero-phosphate dimethacrylate (GPDM) with hydroxyapatite and dentin.

PubMed

Yoshihara, Kumiko; Nagaoka, Noriyuki; Hayakawa, Satoshi; Okihara, Takumi; Yoshida, Yasuhiro; Van Meerbeek, Bart

2018-04-28

Although the functional monomer glycero-phosphate dimethacrylate (GPDM) has since long been used in several dental adhesives and more recently in self-adhesive composite cements and restoratives, its mechanism of chemical adhesion to hydroxyapatite (HAp) is still unknown. We therefore investigated the chemical interaction of GPDM with HAp using diverse chemical analyzers and ultra-structurally characterized the interface of a GPDM-based primer formulation with dentin. HAp particles were added to a GPDM solution for various periods, upon which they were thoroughly washed with ethanol and water prior to being air-dried. As control, 10-methacryloyloxydecyl dihydrogen phosphate (MDP) was used. The molecular interaction of GPDM with HAp was analyzed using X-ray diffraction (XRD) and solid-state nuclear magnetic resonance (NMR) spectroscopy. Crystal formation upon application of GPDM onto dentin was analyzed using thin-film XRD (TF-XRD). Its hydrophobicity was measured using contact-angle measurement. The interaction of GPDM with dentin was characterized using transmission electron microscopy (TEM). XRD revealed the deposition of dicalcium phosphate dihydrate (DCPD: CaHPO 4 ·2H 2 O) on HAp after 24h. NMR confirmed the adsorption of GPDM onto HAp. However, GPDM was easily removed after washing with water, unlike MDP that remained adhered to HAp. Dentin treated with GPDM appeared more hydrophilic compared to dentin treated with MDP. TEM disclosed exposed collagen in the hybrid layer produced by the GPDM-based primer formulation. Although GPDM adsorbed to HAp, it did not form a stable calcium salt. The bond between GPDM and HAp was weak, unlike the strong bond formed by MDP to HAp. Due to its high hydrophilicity, GPDM might be an adequate monomer for an etch-and-rinse adhesive, but appears less appropriate for a 'mild' self-etch adhesive that besides micro-retention ionically interacts with HAp, or for a self-adhesive restorative material. Copyright © 2018 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.

Development of an Aqueous Ophthalmic Solution with an Enhanced-Solubility Enrofloxacin Crystal, and its Clinical Evaluation in Dogs.

PubMed

Miranda-Calderon, Jorge E; Gutierrez, Lilia; Ocampo, Luis; Garcia-Gutierrez, Ponciano; Tapia, Graciela; Sumano, Hector

2018-01-01

The concern about the frequent use of ciprofloxacin in veterinary medicine is linked to increased antimicrobial resistance. The corresponding fluoroquinolone for veterinary use is enrofloxacin. A new solvate form of enrofloxacin, as dihydrate-hydrochloride (enro-C) with higher water solubility than the parent compound, was formulated as an ophthalmic solution (pH 5). A multicentre, longitudinal, non-inferiority clinical study in a non-hospital environment was designed to treat 36 dogs affected by tobramycin-unresponsive conjunctivitis with either the experimental 0.5% enro-C ophthalmic preparation (enro-CG) or a commercial preparation of ciprofloxacin (cipro-G). Other causes of conjunctivitis were ruled out. Pathogens were isolated and minimum inhibitory concentration (MIC) studies of tobramycin were carried out. Three blocks of bacterial resistance were set up, beginning at the established breakpoint i.e., 4 µg/mL; 8 µg/mL and 16 µg/mL. Eighteen dogs were randomly assigned to each block. The enro-CG group was treated with two drops of the referred preparation (10 mg/eye) twice a day for 7 days, and the cipro-G group was treated with four drops of a 0.3% commercially available ciprofloxacin eye-drop preparation (9 mg/eye) twice a day, also for 7 days. Clinical and bacteriological cure rates were evaluated. Enro-C-treated dogs achieved a clinical cure one day earlier than ciprofloxacin-treated dogs, and unlike this latter group, enro-CG achieved bacteriological cure in all cases. No side effects were observed in either group, but dogs treated with enro-C showed no discomfort, allowing easier treatment-compliance. This is the first study reported on the successful formulation of enrofloxacin as an ophthalmic solution. Clinical assessment reveals outstanding clinical efficacy. It is necessary to conduct further research on clinical efficacy and toxicity, with the chronic use of this preparation under different clinical challenges. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Short-term implantation effects of a DCPD-based calcium phosphate cement.

PubMed

Frayssinet, P; Gineste, L; Conte, P; Fages, J; Rouquet, N

1998-06-01

Calcium phosphate cements can be handled in paste form and set in a wet medium after precipitation of calcium phosphate crystals in the implantation site. Depending on the products entering into the chemical reaction leading to the precipitation of calcium phosphates, different phases can be obtained with different mechanical properties, setting times and injectability. We tested a cement composed of a powder, containing beta-tricalcium phosphate (beta-TCP) and sodium pyrophosphate mixed with a solution of phosphoric and sulphuric acids. The cement set under a dicalcium phosphate dihydrate (DCPD)-based matrix containing beta-TCP particles. This was injected with a syringe into a defect drilled in rabbit condyles, the control being an identical defect left empty in the opposite condyle. The condyles were analysed histologically 2, 6 and 18 weeks after implantation. After injection into the bone defect the cement set and formed a porous calcium phosphate structure. Two different calcium phosphate phases with different solubility rates could be identified by scanning electron microscopy (SEM) observation. The less-soluble fragments could be degraded by cell phagocytosis in cell compartments of low pH or integrated in the newly formed bone matrix. The degradation rate of the material was relatively high but compatible with the ingrowth of bone trabeculae within the resorbing material. The ossification process was different from the creeping substitution occurring at the ceramic contact. Bone did not form directly at the cement surface following the differentiation of osteoblasts at the material surface. The trabeculae came to the material surface from the edges of the implantation site. Bone formation in the implantation site was significantly higher than in the control region during the first week of implantation. In conclusion, this material set in situ was well tolerated, inducing a mild foreign-body reaction, which did not impair its replacement by newly formed bone within a few weeks.

Pseudogout at the knee joint will frequently occur after hip fracture and lead to the knee pain in the early postoperative period.

PubMed

Harato, Kengo; Yoshida, Hiroki

2015-01-14

Symptomatic knee joint effusion is frequently observed after hip fracture, which may lead to postoperative knee pain during rehabilitation after hip fracture surgery. However, unfortunately, very little has been reported on this phenomenon in the literature. The purpose of the current study was to investigate the relationship between symptomatic knee effusion and postoperative knee pain and to clarify the reason of the effusion accompanied by hip fracture. A total of 100 patients over 65 years of age with an acute hip fracture after fall were prospectively followed up. Knee effusion was assessed on admission and at the operating room before the surgery. If knee effusion was observed at the time of the surgery, synovial fluid was collected into syringes to investigate the cause of the effusion using a compensated polarized light microscope. Furthermore, for each patient, we evaluated age, sex, radiographic knee osteoarthritis (OA), type of the fracture, laterality, severity of the fracture, and postoperative knee pain during rehabilitation. These factors were compared between patients with and without knee effusion at the time of the surgery. As a statistical analysis, we used Mann-Whitney U-test for patients' age and categorical variables were analyzed by chi-square test or Fisher's exact test. A total of 30 patients presented symptomatic knee effusion at the time of the surgery. In patients with knee effusion, numbers of intertrochanteric fracture, radiographic knee OA, and postoperative knee pain were significantly large compared to those without effusion. In terms of synovial fluid analysis, calcium pyrophosphate dihydrate crystals were observed in 80% of patients with knee effusion. From our study, approximately 63% of patients with knee effusion at the time of the surgery had postoperative knee pain. In addition, this effusion was basically related to pseudogout.

Subchondral cysts (geodes) in arthritic disorders: pathologic and radiographic appearance of the hip joint.

PubMed

Resnick, D; Niwayama, G; Coutts, R D

1977-05-01

A comprehensive study of femoral heads of patients and cadavers with osteoarthritis, rheumatoid arthritis, osteonecrosis, and calcium pyrophosphate dihydrate deposition disease allows insight into the radiographic and pathologic appearance of subchondral radiolucencies in these disorders. The term geode, rather than cyst or pseudocyst, may be a more appropriate decription of these lesions. In osteoarthritis, goedes occur on the pressure segment of the femoral head in association with loss of articular space; in rheumatoid arthritis, they are initially noted at the chondro-osseous junction and subsequently involve the entire femoral head. In osteonecrosis, geodes appear in the necrotic segment of the femoral head. In calcium pyrophosphate deposition disease, geodes resemble those in osteoarthritis but are larger, more numerous, and more widespread.

Synthesis of Single Crystalline ZnO Nanoparticles by Salt-Assisted Spray Pyrolysis

NASA Astrophysics Data System (ADS)

Panatarani, Camellia; Lenggoro, I. Wuled; Okuyama, Kikuo

2003-04-01

LiNO3 was used as a shield in the preparation of single crystalline ZnO particles by a spray pyrolysis process in order to prevent agglomeration and enhance the crystallinity of the ZnO. LiNO3 was added to a precursor solution of zinc acetate dihydrate prior to its atomization by means of an ultrasonic transducer. Agglomerate-free particles having a mean particle size of 26 nm were successfully obtained after washing the product. X-ray diffractometry, field-emission scanning electron micrograph and transmission electron micrograph data indicate that the size and morphology of ZnO were strongly influenced by the operating temperature used and the residence time of the particle in the reactor.

Morphological impact of zinc oxide layers on the device performance in thin-film transistors.

PubMed

Faber, Hendrik; Klaumünzer, Martin; Voigt, Michael; Galli, Diana; Vieweg, Benito F; Peukert, Wolfgang; Spiecker, Erdmann; Halik, Marcus

2011-03-01

Zinc oxide thin-films are prepared either by spin coating of an ethanolic dispersion of nanoparticles (NP, diameter 5 nm) or by spray pyrolysis of a zinc acetate dihydrate precursor. High-resolution electron microscopy studies reveal a monolayer of particles for the low temperature spin coating approach and larger crystalline domains of more than 30 nm for the spray pyrolysis technique. Thin-film transistor devices (TFTs) based on spray pyrolysis films exhibit higher electron mobilities of up to 24 cm2 V(-1) s(-1) compared to 0.6 cm2 V(-1) s(-1) for NP based TFTs. These observations were dedicated to a reduced number of grain boundaries within the transistor channel.

Formation of model polar stratospheric cloud films

NASA Technical Reports Server (NTRS)

Middlebrook, Ann M.; Koehler, Birgit G.; Mcneill, Laurie S.; Tolbert, Margaret A.

1992-01-01

Fourier transform infrared spectroscopy was used to examine the competitive growth of films representative of polar stratospheric clouds. These experiments show that either crystalline nitric acid trihydrate (beta-NAT) or amorphous films with H2O:HNO3 ratios close to 3:1 formed at temperatures 3-7 K warmer than the ice frost point under stratospheric pressure conditions. In addition, with higher HNO3 pressure, we observed nitric acid dihydrate (NAD) formation at temperatures warmer than ice formation. However, our experiments also show that NAD surfaces converted to beta-NAT upon exposure to stratospheric water pressures. Finally, we determined that the net uptake coefficient for HNO3 on beta-NAT is close to unity, whereas the net uptake coefficient for H2O is much less.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thangavelu, Sonia G.; Butcher, Ray J.; Cahill, Christopher L.

Thiophene 2,5-dicarboxylic acid (TDC) was reacted with uranyl acetate dihydrate and one (or none) of six N-donor chelating ligands (2,2'-bipyridine (BPY), 4,4'-dimethyl-2,2'-bipyridine (4-MeBPY), 5,5'-dimethyl-2,2'-bipyridine (5-MeBPY), 6,6'-dimethyl-2,2'-bipyridine (6-MeBPY), 4,4',6,6'-tetramethyl-2,2'-bipyridine (4,6-MeBPY), and tetrakis(2-pyridyl)pyrazine (TPPZ) to result in the crystallization of seven uranyl coordination polymers, which were characterized by their crystal structures and luminescence properties. The seven coordination polymers, Na2[(UO2)2(C6H2O4S)3]·4H2O (1), [(UO2)4(C6H2O4S)5(C10H8N2)2]·C10H10N2·3H2O (2), [(UO2)(C6H2O4S)(C12H12N3)] (3), [(UO2)(C6H2O4S)(C12H12N3)]·H2O (4), [(UO2)2(C6H2O4S)3]·(C12H14N2)·5H2O (5), [(UO2)3(CH3CO2)(C6H2O4S)4](C14H17N2)3·(C14H16N2)·H2O (6), and [(UO2)2(C6H2O4S)3](C24H18N6) (7), consist of either uranyl hexagonal bipyramidal or pentagonal bipyramidal coordination geometries. In all structures, structural variations in the local and global structures of 1–7 are influenced by the positionsmore » (or number) of methyl groups or pyridyl rings on the N-donor species, thus resulting in a wide diversity of structures ranging from single chains, double chains, or 2-D sheets. Direct coordination of N-donor ligands to uranyl centers is observed in the chain structures of 2–4 using BPY, 4-MeBPY, and 5-MeBPY, whereas the N-donor species participate as guests (as either neutral or charge balancing species) in the chain and sheet structures of 5–7 using 6-MeBPY, 4,6-MeBPY, and TPPZ, respectively. Compound 1 is the only structure that does not contain any N-donor ligands and thus crystallizes as a 2-D interpenetrating sheet. The luminescent properties of 1–7 are influenced by the direct coordination or noncoordination of N-donor species to uranyl centers. Compounds 2–4 exhibit typical UO22+ emission upon direct coordination of N-donors, but its absence is observed in 1, 5, 6, and 7, when N-donor species participate as guest molecules. These results suggest that direct coordination of N-donor ligands participate as chromophores, thus resulting in possible UO22+ sensitization. The lack of emission in 1, 5, 6, and 7 may be explained by the extended conjugation of the TDC ligands within their structures.« less

Bleaching of red lake paints in encaustic mummy portraits

NASA Astrophysics Data System (ADS)

Miliani, Costanza; Daveri, Alessia; Spaabaek, Lin; Romani, Aldo; Manuali, Valentina; Sgamellotti, Antonio; Brunetti, Brunetto Giovanni

2010-09-01

The present paper reports on the study of the development of whitish opacity in pink paints in encaustic mummy portraits. Non-invasive measurements carried out on two encaustic portraits belonging to the Ny Carlsberg Glyptotek, Copenhagen, by reflectance FTIR and UV-vis fluorescence have shown that the areas prone to the bleaching phenomenon had been painted with melted beeswax and an anthraquinone vegetal lake mixed with calcium sulphate hemihydrate and dihydrate. The hypothesis that the bleaching disease was neither related to a degradation of the dyes nor to an alteration of the wax but rather to a dehydration-hydration reaction of the CaSO4-H2O system, has been corroborated by the analyses of two microsamples from the bleached areas and ascertained by accelerated ageing experiments on encaustic models.

Room temperature synthesis and enhanced photocatalytic property of CeO2/ZnO heterostructures

NASA Astrophysics Data System (ADS)

Wang, Chao; Fan, Huiqing; Ren, Xiaohu; Fang, Jiawen

2018-02-01

To achieve better photocatalytic performance, we proposed a facile solid-state reaction method to produce CeO2/ZnO heterostructures. Ceria and zinc oxide were synthesized simultaneously by thoroughly grinding the mixture of zinc acetate dihydrate, cerium nitrate hexahydrate and sodium hydroxide. The morphology of the as-prepared heterostructures varies dramatically as different amount of ceria was introduced in the composition. The photocatalytic performance of CeO2/ZnO heterojunctions was 4.6 times higher than that of pure ZnO. The enhanced photocatalytic activity could be ascribed to that more electrons and holes could transport to the surface of catalysts and react with the pollution due to the extended light-responsive range, accelerated migration, increased specific surface area and suppressed recombination of photogenerated carriers.

Plasma oxalic acid and calcium levels in oxalate poisoning

PubMed Central

Zarembski, P. M.; Hodgkinson, A.

1967-01-01

Observations are reported on five cases of suicide or attempted suicide by poisoning with oxalic acid or ethylene glycol. Elevated oxalic acid levels were observed in the plasma, stomach contents, and a number of tissues. Raised oxalic acid levels in plasma were associated with reduced total and ultrafilterable calcium levels. It is suggested that the reduction in plasma total calcium level is due mainly to the deposition of calcium oxalate in the soft tissues, but inhibition of the parathyroid glands may be a contributory factor. Microscopic examination of various tissues indicated that oxalic acid is deposited in the tissues in two forms: (1) crystalline calcium oxalate dihydrate in the kidney and (2) a non-crystalline complex of calcium oxalate and lipid in liver and other tissues. PMID:5602563

Poly[[tetra-μ3-acetato-hexa-μ2-acetato­diaqua-μ2-oxalato-tetra­lanthanum(III)] dihydrate

PubMed Central

Di, Wen-Jing; Lan, Shao-Min; Zhang, Qun; Liang, Yun-Xiao

2011-01-01

The title compound, {[La4(CH3CO2)10(C2O4)(H2O)2]·2H2O}n, exhibits a two-dimensional layered structure with the oxalate and acetate ligands acting as bridges. The asymmetric unit contains two crystallographically independent lanthanum(III) ions, half of an oxalate ligand, five acetate ligands, one coordinated water mol­ecule and one uncoordinated water mol­ecule. The coordination numbers of the two La ions are 9 and 10. Adjacent layers of the structure, which extend parallel to (100), are linked by O–H⋯O hydrogen bonds and are also held together by van der Waals inter­actions between the CH3 groups of the acetate anions. PMID:22064832

The inclusion of electroactive β-phase in Sn2+ incorporated PVDF composite film for improving dielectric properties and piezoelectric energy generation

NASA Astrophysics Data System (ADS)

Alam, Md. Mehebub; Mandal, Dipankar

2018-04-01

Low content (0.5 wt. %) of dihydrate tin chloride (Sn2+) salt leads to inclusion of 98 % electroactive phase in poly(vinylidene fluoride) (PVDF), out of this a high yield of piezoelectric β-phase (˜ 49%) is found, which is most desirable for mechanical energy harvesting application. It is also found that Sn2+ salt can significantly enhanced the dielectric property of resulting Sn2+ incorporated PVDF composite film. Thus, the enhancement of β-phase in the PVDF/Sn2+ composite film owns to be a potential material for mechanical energy harvesting application. We have also demonstrated the mechanical energy harvesting capability of the nanogenerator (NG) made with PVDF/Sn2+ composite film under repeated human finger touch.

Vaginal oxytetracycline concentrations.

PubMed Central

Thin, R N; Al Rawi, Z H; Simmons, P D; Treharne, J; Tabaqchali, S

1979-01-01

Although tetracycline preparations are widely used in departments of genitourinary medicine, or sexually transmitted diseases clinics, little is known of the concentrations of these preparations in genital secretions. For this reason a microbiological method was used for estimating oxytetracycline concentrations in vaginal secretions. These concentrations varied from 0.6 to 6.5 microgram/ml in 19 women who had had sexual contact with a man with non-specific urethritis and who were taking oxytetracycline dihydrate 250 mg four times daily. They were well in excess of the minimum inhibitory concentration of oxytetracycline (0.2 microgram/ml) for the strains of Chlamydia trachomatis isolated from the patients with positive culture results. Thus, oxytetracycline 250 mg four times daily appears to be a satisfactory regimen for the treatment of chlamydial genital infection in women. PMID:509190

High-performance liquid chromatographic method optimization for ondansetron assay in extemporaneous topical gel and in marketed products.

PubMed

Quamrun, Masuda; Mamoon, Rashid; Nasheed, Shams; Randy, Mullins

2014-01-01

The compounding and evaluation of ondansetron hydrochloride dihydrate topical gel, 2.5% w/w, were conducted in this study. The gelling agent was Carbopol 940. Ethanol 70% in purified water was used to dissolve the drug and disperse the gelling agent. A gel was formed by adding drops of 0.1 N sodium hydroxide solution. To assay this gel, we developed a simple and reproducible stability--indicating high-performance liquid chromatographic method. This method was validated for specificity, accuracy, and precision. The compounded gel was assayed in triplicate, and the average recovery was 98.3%. Ondansetron marketed products were analyzed for comparison with the compounded formulation. Assay, accuracy, and precision data of the compounded topical gel were comparable to the marketed products.

Potassium (2,2'-bipyridine-κN,N')bis-(carbonato-κO,O')cobaltate(III) dihydrate.

PubMed

Wang, Jian-Fei; Lin, Jian-Li

2010-09-30

In the title compound, K[Co(CO(3))(2)(C(10)H(8)N(2))]·2H(2)O, the Co(III) atom is coordinated by two bipyridine N atoms and four O atoms from two bidentate chelating carbonate anions, and thus adopts a distorted octa-hedral N(2)O(4) environment. The [Co(bipy)(CO(3))(2)](-) (bipy is 2,2'-bipyridine) -units are stacked along [100] via π-π stacking inter-actions, with inter-planar distances between the bipyridine rings of 3.36 (4) and 3.44 (6) Å, forming chains. Classical O-H⋯O hydrogen-bonding inter-actions link the chains, forming channels along (100) in which the K(+) ions reside and leading to a three-dimensional supra-molecular architecture.

Drug repurposing: In-vitro anti-glycation properties of 18 common drugs

PubMed Central

Rasheed, Saima; Sánchez, Sara S.; Yousuf, Sammer; Honoré, Stella M.; Choudhary, M. Iqbal

2018-01-01

Drug repositioning or repurposing, i.e. identifying new indications for existing drugs, has gained increasing attention in the recent years. This approach enables the scientists to discover “new targets” for known drugs in a cost and time efficient manner. Glycation, the non-enzymatic reaction of sugars with proteins or nucleic acids to form early glycation (Amadori or fructosamine) products, is a key molecular basis of diabetic complications. Inhibiting the process of non-enzymatic protein glycation is one of the key strategies to prevent glycation-mediated diabetic complications. The present study focuses on the anti-glycation activity of 18 drugs, commonly used for the treatment of gastrointestinal, central nervous system, inflammatory diseases, bacterial infections, and gout. This study was carried out by using two in-vitro protein anti-glycation assay models. Results revealed that nimesulide (3), a non-steroidal anti-inflammatory drug, possesses a good anti-glycation activity in in-vitro BSA-MG and BSA-glucose glycation models with IC50 values of 330.56 ± 2.90, and 145.46 ± 16.35 μM, respectively. Phloroglucinol dihydrate (11), a drug used for the treatment of gastrointestinal diseases, showed a weak activity in BSA-MG glycation model (IC50 = 654.89 ± 2.50 μM), while it showed a good activity in BSA-glucose assay (IC50 = 148.23 ± 0.15 μM). Trimethylphloroglucinol (9), a drug used for the treatment of pain related to functional disorders of the digestive and biliary tracts, also showed a good antiglycation activity in BSA-MG model (IC50 = 321.15 ± 1.26 μM), while it was found to be inactive in in-vitro BSA-glucose assay (IC50 = 12.95% inhibition). These activities of drugs were compared with the anti-glycation activity of the standard, rutin (IC50 = 294.5 ± 1.50 μM in BSA-MG glycation model, and IC50 = 86.94 ± 0.24 μM in BSA- glucose model). Rest of the drugs exhibited a relatively weak antiglycation activity. This study identifies nimesulide (3), and phloroglucinol dihydrate (11) as new inhibitors of in-vitro protein glycation for further investigations as potential anti-diabetic agents. PMID:29300762

High precision mapping of kidney stones using μ-IR spectroscopy to determine urinary lithogenesis.

PubMed

Blanco, Francisco; Ortiz-Alías, Pilar; López-Mesas, Montserrat; Valiente, Manuel

2015-06-01

Evolution of urinary lithiasis is determined by the metabolism and life-style of the related patient. The appropriate classification of the stone is mandatory for the identification of the lithogenic process. In this study, cros-sections from a single stone of each of the most frequent urolithiasis types (calcium oxalate mono and dihydrate and carbonate apatite) have been selected and imaged using IR microspectroscopy. Moreover, the use of high definition sFTIR (synchrotron source) has revealed hidden information to the conventional FTIR. This work has demonstrated that minor components become key factors on the description of the stages of stone formation. Intensity map for COM (1630 cm(-1) peak). The high spatial definition achieved is key for the precise description of the kidney stone history. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tyrosinase autoactivation and the problem of the lag period.

PubMed

Naish-Byfield, S; Riley, P A

1998-06-01

Evidence is presented for the binding of the quinone oxidation product of the monohydric phenol substrate, 4-hydroxyanisole, to mushroom tyrosinase. Column chromatography and SDS-PAGE separation showed labelling of the enzyme when incubated with 14C ring-labelled 4-hydroxyanisole. It is proposed that covalent binding to the enzyme and other proteins is through reaction of accessible nucleophilic groups, including thiols and amino groups, with the anisylquinone. This reductive addition enables the indirect generation of the catecholic substrate, which acts as an electron donor for the bicupric active site of met-tyrosinase and explains the lag kinetics of tyrosinase oxidation of non-cyclizing substrates. The effects of diluting the enzyme or the addition of amino acids on the lag period was consistent with a mechanism involving indirect generation of the dihydric phenol, which acts as the met-enzyme-recruiting substrate.

Aqua[bis(pyrimidin-2-yl-kappa N)amine](carbonato-kappa 2O,O')copper(II) dihydrate.

PubMed

van Albada, Gerard A; Mutikainen, Ilpo; Turpeinen, Urho; Reedijk, Jan

2002-03-01

The title mononuclear complex, [Cu(CO(3))(C(8)H(7)N(5))(H(2)O)] x 2H(2)O, was obtained by fixation of CO(2) by a mixture of copper(II) tetrafluoroborate and the ligand bis(pyrimidin-2-yl)amine in ethanol/water. The Cu(II) ion of the complex has a distorted square-pyramidal environment, with a basal plane formed by two N atoms of the ligand and two chelating O atoms of the carbonate group, while the apical position is occupied by the O atom of the coordinating water molecule. In the solid state, hydrogen-bonding interactions are dominant, the most unusual being the Watson-Crick-type coplanar ligand pairing through two N--H...N bonds. Lattice water molecules also participate in hydrogen bonding.

Purine 3':5'-cyclic nucleotides with the nucleobase in a syn orientation: cAMP, cGMP and cIMP.

PubMed

Řlepokura, Katarzyna Anna

2016-06-01

Purine 3':5'-cyclic nucleotides are very well known for their role as the secondary messengers in hormone action and cellular signal transduction. Nonetheless, their solid-state conformational details still require investigation. Five crystals containing purine 3':5'-cyclic nucleotides have been obtained and structurally characterized, namely adenosine 3':5'-cyclic phosphate dihydrate, C10H12N5O6P·2H2O or cAMP·2H2O, (I), adenosine 3':5'-cyclic phosphate 0.3-hydrate, C10H12N5O6P·0.3H2O or cAMP·0.3H2O, (II), guanosine 3':5'-cyclic phosphate pentahydrate, C10H12N5O7P·5H2O or cGMP·5H2O, (III), sodium guanosine 3':5'-cyclic phosphate tetrahydrate, Na(+)·C10H11N5O7P(-)·4H2O or Na(cGMP)·4H2O, (IV), and sodium inosine 3':5'-cyclic phosphate tetrahydrate, Na(+)·C10H10N4O7P(-)·4H2O or Na(cIMP)·4H2O, (V). Most of the cyclic nucleotide zwitterions/anions [two from four cAMP present in total in (I) and (II), cGMP in (III), cGMP(-) in (IV) and cIMP(-) in (V)] are syn conformers about the N-glycosidic bond, and this nucleobase arrangement is accompanied by Crib-H...Npur hydrogen bonds (rib = ribose and pur = purine). The base orientation is tuned by the ribose pucker. An analysis of data obtained from the Cambridge Structural Database made in the context of syn-anti conformational preferences has revealed that among the syn conformers of various purine nucleotides, cyclic nucleotides and dinucleotides predominate significantly. The interactions stabilizing the syn conformation have been indicated. The inter-nucleotide contacts in (I)-(V) have been systematized in terms of the chemical groups involved. All five structures display three-dimensional hydrogen-bonded networks.

Simple and Rapid Synthesis of Magnetite/Hydroxyapatite Composites for Hyperthermia Treatments via a Mechanochemical Route

PubMed Central

Iwasaki, Tomohiro; Nakatsuka, Ryo; Murase, Kenya; Takata, Hiroshige; Nakamura, Hideya; Watano, Satoru

2013-01-01

This paper presents a simple method for the rapid synthesis of magnetite/hydroxyapatite composite particles. In this method, superparamagnetic magnetite nanoparticles are first synthesized by coprecipitation using ferrous chloride and ferric chloride. Immediately following the synthesis, carbonate-substituted (B-type) hydroxyapatite particles are mechanochemically synthesized by wet milling dicalcium phosphate dihydrate and calcium carbonate in a dispersed suspension of magnetite nanoparticles, during which the magnetite nanoparticles are incorporated into the hydroxyapatite matrix. We observed that the resultant magnetite/hydroxyapatite composites possessed a homogeneous dispersion of magnetite nanoparticles, characterized by an absence of large aggregates. When this material was subjected to an alternating magnetic field, the heat generated increased with increasing magnetite concentration. For a magnetite concentration of 30 mass%, a temperature increase greater than 20 K was achieved in less than 50 s. These results suggest that our composites exhibit good hyperthermia properties and are promising candidates for hyperthermia treatments. PMID:23629669

How do Polar Stratospheric Clouds Form?

NASA Technical Reports Server (NTRS)

Drdla, Katja; Gandrud, Bruce; Baumgardner, Darrel; Herman, Robert; Gore, Warren J. (Technical Monitor)

2000-01-01

SOLVE measurements have been compared with results from a microphysical model to understand the composition and formation of the polar stratospheric clouds (PSCs) observed during SOLVE. Evidence that the majority of the particles remain liquid throughout the winter will be presented. However, a small fraction of the particles do freeze, and the presence of these frozen particles can not be explained by current theories, in which the only freezing mechanism is homogeneous freezing to ice below the ice frost point. Alternative formation mechanisms, in particular homogeneous freezing above the ice frost point and heterogeneous freezing, have been explored using the microphysical model. Both nitric acid trihydrate (NAT) and nitric acid dihydrate (NAD) have been considered as possible compositions for the solid-phase nitric acid aerosols. Comparisons between the model results and the SOLVE measurements will be used to constrain the possible formation mechanisms. Other effects of these frozen particles will also be discussed, in particular denitrification.

Microphysical Modelling of the 1999-2000 Arctic Winter. 3; Impact of Homogeneous Freezing on PSCs

NASA Technical Reports Server (NTRS)

Drdla, K.

2003-01-01

Simulations of the 1999-2000 winter have tested the effect on polar stratospheric clouds (PSCs) of the homogeneous freezing of liquid ternary solutions into nitric acid trihydrate (NAT) and nitric acid dihydrate (NAD). Proposed laboratory-derived volume-based and surface-based homogeneous freezing rates have both been examined, including different assumptions about the extrapolation of laboratory measurements to atmospheric conditions. Widespread PSC formation and denitrification are possible in several of the scenarios examined. However, the simulations are all unable to explain the solid-phase PSCs observed early in the 1999-2000 winter, and are unable to reproduce the measured extent of vortex denitrification. These problems can both be attributed to the relatively cold temperatures, more than 5 K below the NAT condensation point, necessary for effective homogeneous freezing. Therefore synoptic-scale homogeneous freezing appears unlikely to be the primary mechanism responsible for solid-phase PSC formation.

IR-UV spectroscopy of jet-cooled 1-indanol: Restriction of the conformational space by hydration

NASA Astrophysics Data System (ADS)

Bouchet, Aude; Altnöder, Jonas; Broquier, Michel; Zehnacker, Anne

2014-11-01

The effect of hydration on a flexible amphiphilic molecule has been studied on the example of 1-hydroxyindan (1-indanol). Studies in jet-cooled conditions by means of resonance-enhanced two-photon ionization and IR-UV double resonance experiments show that the mono-hydrate 1-indanol(H2O) is formed in a dominant isomer, as well as the di-hydrate 1-indanol(H2O)2. 1-Indanol(H2O) favors a cooperative hydrogen bond pattern with -OH⋯O(H)-H⋯π topology, while 1-indanol(H2O)2 forms a cyclic hydrogen bond network with three OH⋯O interactions. The single conformation observed for the hydrates contrasts with the bare molecule which shows two dominant conformations, with the hydroxyl in axial or in equatorial position, respectively. Hydration therefore results in a restriction of the conformational space and conformational locking.

(2′-Amino-4,4′-bi-1,3-thia­zol-2-aminium-κ2 N,N′)aqua­[citrato(4−)-κ3 O,O′,O′′)chromium(III) dihydrate

PubMed Central

Liu, Bing-Xin; Du, Mei; Chen, Guang-Hua; Sun, Xiao-Yuan

2009-01-01

In the title compound, [Cr(C6H7N4S2)(C6H4O7)(H2O)]·2H2O, the CrIII atom is in a distorted octa­hedral environment, coordinated by one water mol­ecule, two N atoms from a protonated diamino­bithia­zole ligand and three O atoms from a citrate(4−) anion. The complex is zwitterionic, with the H atom from the uncoordinated carboxyl­ate group of the citrate anion transferred to one amino group of the diamino­bithia­zole ligand. O—H⋯O and N—H⋯O hydrogen bonds link the complexes into layers including the two uncoordinated water mol­ecules. PMID:21582094

Structural and Optoelectronic Properties of SnO2 Thin Films Doped by Group-Ia Elements

NASA Astrophysics Data System (ADS)

Benhebal, Hadj; Benrabah, Bedhiaf; Ammari, Aek; Madoune, Yacine; Lambert, Stéphanie D.

This paper presents the results of an experimental work devoted to the synthesis and the characterization of tin dioxide (SnO2) thin layers doped with group-IA elements (Li, Na and K). The materials were synthesized by the sol-gel method and deposited by dip-coating, using tin (II) chloride dihydrate as a source of tin and absolute ethyl alcohol as solvent. Thin films prepared were characterized by several techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (IR), visible and ultraviolet spectroscopy and complex impedance method. The results obtained show that the materials kept their tetragonal rutile structure with preferred orientation of (101), whereas doping leads to a reduction of their energy band gap. The complex impedance analysis suggests that the different processes occurring at the electrode interface are modeled by an electrical circuit not affected by the doping.

Effects of Weightlessness of Aurelia Ephyra Differentiation and Statolith Synthesis

NASA Technical Reports Server (NTRS)

Spangenberg, D. B.

1985-01-01

Aurelia polyps are especially suited for space flight experiments because they are very small (2 to 4 mm), form ephyrae with gravity sensing structures in 6 to 7 days, and can be reared easily and inexpensively in the laboratory. During iodine-induced metamorphosis ephyrae develop in sequential order from the oral to the aboral end of the polyps. Eight sites of gravity receptors (rhopalia) form per ephyra. These structures have sacs of statoliths at their distal end, which are composed of calcium sulfate dihydrate. Only one statolith forms per cell (statocyte) and the cells collect at the distal end of the rhopalia forming statocysts. Rhopalia with statocysts are necessary for the righting reflex of swimming medusae. Using the Aurelia Metamorphosis Test System (Spangenberg, 1984) for the past eight months, the effects of clinostat rotation in the horizontal and verticall planes on the development of ephyrae and the synthesis of their statoliths were investigated.

Potassium (2,2′-bipyridine-κ2 N,N′)bis­(carbonato-κ2 O,O′)cobaltate(III) dihydrate

PubMed Central

Wang, Jian-Fei; Lin, Jian-Li

2010-01-01

In the title compound, K[Co(CO3)2(C10H8N2)]·2H2O, the Co(III) atom is coordinated by two bipyridine N atoms and four O atoms from two bidentate chelating carbonate anions, and thus adopts a distorted octa­hedral N2O4 environment. The [Co(bipy)(CO3)2]− (bipy is 2,2′-bipyridine) ­units are stacked along [100] via π–π stacking inter­actions, with inter­planar distances between the bipyridine rings of 3.36 (4) and 3.44 (6) Å, forming chains. Classical O—H⋯O hydrogen-bonding inter­actions link the chains, forming channels along (100) in which the K+ ions reside and leading to a three-dimensional supra­molecular architecture. PMID:21587447

Preparation and Supercooling Modification of Salt Hydrate Phase Change Materials Based on CaCl₂·2H₂O/CaCl₂.

PubMed

Xu, Xiaoxiao; Dong, Zhijun; Memon, Shazim Ali; Bao, Xiaohua; Cui, Hongzhi

2017-06-23

Salt hydrates have issues of supercooling when they are utilized as phase change materials (PCMs). In this research, a new method was adopted to prepare a salt hydrate PCM (based on a mixture of calcium chloride dihydrate and calcium chloride anhydrous) as a novel PCM system to reduce the supercooling phenomenon existing in CaCl₂·6H₂O. Six samples with different compositions of CaCl₂ were prepared. The relationship between the performance and the proportion of calcium chloride dihydrate (CaCl₂·2H₂O) and calcium chloride anhydrous (CaCl₂) was also investigated. The supercooling degree of the final PCM reduced with the increase in volume of CaCl₂·2H₂O during its preparation. The PCM obtained with 66.21 wt % CaCl₂·2H₂O reduced the supercooling degree by about 96.8%. All six samples, whose ratio of CaCl₂·2H₂O to (CaCl₂ plus CaCl₂·2H₂O) was 0%, 34.03%, 53.82%, 76.56%, 90.74%, and 100% respectively, showed relatively higher enthalpy (greater than 155.29 J/g), and have the possibility to be applied in buildings for thermal energy storage purposes. Hence, CaCl₂·2H₂O plays an important role in reducing supercooling and it can be helpful in adjusting the solidification enthalpy. Thereafter, the influence of adding different percentages of Nano-SiO₂ (0.1 wt %, 0.3 wt %, 0.5 wt %) in reducing the supercooling degree of some PCM samples was investigated. The test results showed that the supercooling of the salt hydrate PCM in Samples 6 and 5 reduced to 0.2 °C and 0.4 °C respectively. Finally, the effect of the different cooling conditions, including frozen storage (-20 °C) and cold storage (5 °C), that were used to prepare the salt hydrate PCM was considered. It was found that both cooling conditions are effective in reducing the supercooling degree of the salt hydrate PCM. With the synergistic action of the two materials, the performance and properties of the newly developed PCM systems were better especially in terms of reducing the supercooling degree of the PCM. The novel composite PCMs are promising candidates for thermal energy storage applications.

Efficacy of a New Recrystallized Enrofloxacin Hydrochloride-Dihydrate against Leptospirosis in a Hamster Model.

PubMed

Carrascosa, Alma; Gutierrez, Lilia; De la Peña, Alejandro; Candanosa, Irma E; Tapia, Graciela; Sumano, Hector

2017-11-01

A trial on Syrian hamsters ( Mesocricetus auratus ) infected with Leptospira interrogans serovar Canicola was established to compare treatment efficacies of daily intramuscular (i.m.) injections of either 10 mg/kg of 5% enrofloxacin (Baytril [BE]; Bayer Animal Health, Mexico) or the same dose of enrofloxacin hydrochloride-dihydrate (enro-C). Hamsters were experimentally infected via the oral submucosa with 400 microorganisms/animal, in a sequential time schedule aligned to the initial treatment day, and were treated in groups as follows: a group treated with 5% enrofloxacin daily for 7 days after 24 h of infection (group BE 24 ); a group treated as described for group BE 24 but with enro-C (enro-C 24 ); a group also treated with 5% enrofloxacin but starting at 72 h after infection (BE 74 ); a group treated as described for group BE 74 but with injection of enro-C (enro-C 74 ). An untreated-uninfected control group (group CG - ) and an infected-untreated control group (group CG + ) were assembled ( n = 18 in all groups). Weights and temperatures of the hamsters were monitored daily for 28 days. After hamsters were euthanatized or following death, necropsy, histopathology, macroscopic agglutination tests (MAT), bacterial culture, and PCR were performed. The mortality rates were 38.8% in group BE 24 and 100% in group BE 74 No mortality was observed in group enro-C 24 , and 11.1% mortality was recorded in group enro-C 74 The mortality rates in groups CG + and CG - were 100% and zero, respectively. Combined necropsy and histopathologic findings revealed signs of septicemia and organ damage in groups BE 24 , BE 72 , and CG + Groups enro-C 24 and CG - showed no lesions. Moderated lesions were registered in 3 hamsters in group enro-C 72 MAT results were positive in 83.3% of BE 24 hamsters (83.3%) and 100% of BE 72 and CG + hamsters; MAT results were positive in 16.7% in group Enro-C 24 and 38.9% in group enro-C 72 Only 4/18 were PCR positive in group enro-C 72 and only 1 in group enro-C 24 ( P < 0.05). It can be concluded that enro-C may be a viable option to treat leptospirosis in hamsters and that this may be the case in other species. Copyright © 2017 American Society for Microbiology.

Hygroscopic behavior and chemical composition evolution of internally mixed aerosols composed of oxalic acid and ammonium sulfate

NASA Astrophysics Data System (ADS)

Wang, Xiaowei; Jing, Bo; Tan, Fang; Ma, Jiabi; Zhang, Yunhong; Ge, Maofa

2017-10-01

Although water uptake of aerosol particles plays an important role in the atmospheric environment, the effects of interactions between components on chemical composition and hygroscopicity of particles are still not well constrained. The hygroscopic properties and phase transformation of oxalic acid (OA) and mixed particles composed of ammonium sulfate (AS) and OA with different organic to inorganic molar ratios (OIRs) have been investigated by using confocal Raman spectroscopy. It is found that OA droplets first crystallize to form OA dihydrate at 71 % relative humidity (RH), and further lose crystalline water to convert into anhydrous OA around 5 % RH during the dehydration process. The deliquescence and efflorescence point for AS is determined to be 80.1 ± 1.5 % RH and 44.3 ± 2.5 % RH, respectively. The observed efflorescence relative humidity (ERH) for mixed OA / AS droplets with OIRs of 1 : 3, 1 : 1 and 3 : 1 is 34.4 ± 2.0, 44.3 ± 2.5 and 64.4 ± 3.0 % RH, respectively, indicating the elevated OA content appears to favor the crystallization of mixed systems at higher RH. However, the deliquescence relative humidity (DRH) of AS in mixed OA / AS particles with OIRs of 1 : 3 and 1 : 1 is observed to occur at 81.1 ± 1.5 and 77 ± 1.0 % RH, respectively. The Raman spectra of mixed OA / AS droplets indicate the formation of ammonium hydrogen oxalate (NH4HC2O4) and ammonium hydrogen sulfate (NH4HSO4) from interactions between OA and AS in aerosols during the dehydration process on the time scale of hours, which considerably influence the subsequent deliquescence behavior of internally mixed particles with different OIRs. The mixed OA / AS particles with an OIR of 3 : 1 exhibit no deliquescence transition over the RH range studied due to the considerable transformation of (NH4)2SO4 into NH4HC2O4 with a high DRH. Although the hygroscopic growth of mixed OA / AS droplets is comparable to that of AS or OA at high RH during the dehydration process, Raman growth factors of mixed particles after deliquescence are substantially lower than those of mixed OA / AS droplets during the efflorescence process and further decrease with elevated OA content. The discrepancies for Raman growth factors of mixed OA / AS particles between the dehydration and hydration process at high RH can be attributed to the significant formation of NH4HC2O4 and residual OA, which remain solid at high RH and thus result in less water uptake of mixed particles. These findings improve the understanding of the role of reactions between dicarboxylic acid and inorganic salt in the chemical and physical properties of aerosol particles, and might have important implications for atmospheric chemistry.

Sodium Peroxide Dihydrate or Sodium Superoxide: The Importance of the Cell Configuration for Sodium-Oxygen Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bi, Xuanxuan; Wang, Rongyue; Ma, Lu

In sodium–oxygen (Na–O2) batteries, multiple discharge products have been observed by different research groups. Given the fact that different materials, gas supplies, and cell configurations are used by different groups, it is a great challenge to draw a clear conclusion on the formation of the different products. Here, two different cell setups are used to investigate the cell chemistries of Na–O2 batteries. With the same materials and gas supplies, a peroxide-based product is observed in a glass chamber cell and a superoxide-based product is observed in a stainless-steel cell. Ex situ high-energy X-ray diffraction (HEXRD) and Raman spectroscopy are performedmore » to investigate the structure and composition of the product. In addition, in situ XRD is used to investigate the structure evolution of the peroxide-based product. The findings highlight the importance of the cell design and emphasize the critical environment of the formation of the discharge products of Na–O2 batteries.« less

Percolation Diffusion into Self-Assembled Mesoporous Silica Microfibres

PubMed Central

Canning, John; Huyang, George; Ma, Miles; Beavis, Alison; Bishop, David; Cook, Kevin; McDonagh, Andrew; Shi, Dongqi; Peng, Gang-Ding; Crossley, Maxwell J.

2014-01-01

Percolation diffusion into long (11.5 cm) self-assembled, ordered mesoporous microfibres is studied using optical transmission and laser ablation inductive coupled mass spectrometry (LA-ICP-MS). Optical transmission based diffusion studies reveal rapid penetration (<5 s, D > 80 μm2∙s−1) of Rhodamine B with very little percolation of larger molecules such as zinc tetraphenylporphyrin (ZnTPP) observed under similar loading conditions. The failure of ZnTPP to enter the microfibre was confirmed, in higher resolution, using LA-ICP-MS. In the latter case, LA-ICP-MS was used to determine the diffusion of zinc acetate dihydrate, D~3 × 10−4 nm2∙s−1. The large differences between the molecules are accounted for by proposing ordered solvent and structure assisted accelerated diffusion of the Rhodamine B based on its hydrophilicity relative to the zinc compounds. The broader implications and applications for filtration, molecular sieves and a range of devices and uses are described. PMID:28348290

Kinetics Study on the Effect of NaCl on the CaSO4 Dissolution Behavior

NASA Astrophysics Data System (ADS)

Song, Jingyao; Shi, Peiyang; Wang, Yeguang; Jiang, Maofa

2018-01-01

The study of the dissolution kinetics of CaSO4 is essential for the control of the dissolution and recrystallization behavior of CaSO4. In this work, the kinetic behavior of CaSO4 dissolved in NaCl solution was investigated by means of conductivity meter. The results show that with the increase of concentration of NaCl, the temperature rise and the time prolonged, the dissolution rate of dihydrate CaSO4 gradually increases, and the dissolved apparent activation energy is gradually decreased. When the NaCl concentration is 1.8%, the dissolution kinetic equation is 1-(1-α) 1/3=5.46*10-4exp (-9147/RT) t; When the NaCl concentration is 3.0%, the dissolution kinetic equation is 1-(1-α) 1/3=2.81×10-4 exp (-6753/RT)t; When the NaCl concentration is 3.6%, the dissolution kinetic equation is 1-(1-α) 1/3=3.07×l0-4exp(-6103/RT)t.

Hydrothermal Synthesis and Acetylene Sensing Properties of Variety Low Dimensional Zinc Oxide Nanostructures

PubMed Central

Chen, Weigen; Peng, Shudi; Zeng, Wen

2014-01-01

Various morphologies of low dimensional ZnO nanostructures, including spheres, rods, sheets, and wires, were successfully synthesized using a simple and facile hydrothermal method assisted with different surfactants. Zinc acetate dihydrate was chosen as the precursors of ZnO nanostructures. We found that polyethylene glycol (PEG), polyvinylpyrrolidone (PVP), glycine, and ethylene glycol (EG) play critical roles in the morphologies and microstructures of the synthesized nanostructures, and a series of possible growth processes were discussed in detail. Gas sensors were fabricated using screen-printing technology, and their sensing properties towards acetylene gas (C2H2), one of the most important arc discharge characteristic gases dissolved in oil-filled power equipments, were systematically measured. The ZnO nanowires based sensor exhibits excellent C2H2 sensing behaviors than those of ZnO nanosheets, nanorods, and nanospheres, indicating a feasible way to develop high-performance C2H2 gas sensor for practical application. PMID:24672324

Calcium phosphates deposited on titanium electrode surface--part 1: Effect of the electrode polarity and oxide film on the deposited materials.

PubMed

Okawa, Seigo; Watanabe, Kouichi; Kanatani, Mitsugu

2013-01-01

We report experimental results about the effect of polarity of electrode and anodized titanium oxide film on the deposited materials by electrolysis of an acidic calcium phosphate solution. Mirror-polished titanium and anodized titanium were used as anode or cathode, and a Pt plate was used as a counter electrode. The load voltage was held constant at 20 VDC. No deposited materials were found on the anode surface. On the other hand, dicalcium phosphate dihydrate (DCPD) was deposited on the cathode surface at the beginning of the electrolysis. After the electrolysis time 600 s, the non-stoichiometric hydroxyapatite (HAp) with several hundred nanometers was formed on the specimen surface. Based on X-ray photoelectron spectroscopy data, the anodized oxide film contained both P(5+) and P(3+) ions. This characteristic of the oxide film and the electrolysis conditions were related to the behavior of the deposition of ultra fine HAp with high crystallinity.

Cocrystal dissociation in the presence of water: a general approach for identifying stable cocrystal forms.

PubMed

Eddleston, Mark D; Madusanka, Nadeesh; Jones, William

2014-09-01

In previous studies, cocrystals have been shown to be susceptible to dissociation at high humidity because of differences in the solubilities of the two coformer molecules, especially when these molecules can form hydrates. Contrastingly, however, the propensity of the pharmaceutically active compound caffeine to hydrate formation is reduced by cocrystallization with oxalic acid. Here, the stability of the oxalic acid cocrystal of caffeine is investigated from a thermodynamic perspective through the use of aqueous slurries of caffeine hydrate and oxalic acid dihydrate. Conversion to the anhydrous caffeine-oxalic acid cocrystal occurred under these conditions confirming that this form is thermodynamically stable in an aqueous environment. The slurry methodology was further developed as a general approach to screening for cocrystals that are not susceptible to dissociation at high humidity. In this manner, cocrystals of the hydrate-forming molecules theophylline, carbamazepine, and piroxicam that are stable at high humidity, indefinitely avoiding hydrate formation, were identified. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Trehalase: A New Pollen Enzyme

PubMed Central

Gussin, Arnold E. S.; McCormack, Jeffrey H.; Waung, Lucille Yih-Lo; Gluckin, Doreen S.

1969-01-01

Pollen from 5 plant species (Lycopersicon pimpinellifolium Mill., Hermerocallis minor Mill., Galtonia condicans Decne., Camellia japonica L., and Lathyrus odoratus L.) representing 4 families germinated well in media containing trehalose as the sole carbon source. Data are presented indicating that pollen metabolized this disaccharide for germination and subsequent pollen-tube growth; the sugar was not merely an osmoregulator. An inhibitor of trehalase activity depressed germination in trehalose but not in sucrose. Phloridzin dihydrate, an inhibitor of glucose transport, depressed germination in both disaccharides. Biochemical tests demonstrated that a pollen extract was capable of hydrolyzing trehalose to its constituent glucose monomers. Heat inactivation experiments confirmed the presence of a distinct trehalase having a rigid specificity for its substrate. By this method, trehalase activity was completely distinguishable from the activities of other α- and β-glucosidases and β-galactosidases. Localization data indicated that the enzyme diffused from intact grains and was probably soluble. The presence of its substrate could not be demonstrated in pollen or in stigmatic or stylar tissues. PMID:5379538

Trehalase: a new pollen enzyme.

PubMed

Gussin, A E; McCormack, J H; Waung, L Y; Gluckin, D S

1969-08-01

Pollen from 5 plant species (Lycopersicon pimpinellifolium Mill., Hermerocallis minor Mill., Galtonia condicans Decne., Camellia japonica L., and Lathyrus odoratus L.) representing 4 families germinated well in media containing trehalose as the sole carbon source. Data are presented indicating that pollen metabolized this disaccharide for germination and subsequent pollen-tube growth; the sugar was not merely an osmoregulator. An inhibitor of trehalase activity depressed germination in trehalose but not in sucrose. Phloridzin dihydrate, an inhibitor of glucose transport, depressed germination in both disaccharides. Biochemical tests demonstrated that a pollen extract was capable of hydrolyzing trehalose to its constituent glucose monomers. Heat inactivation experiments confirmed the presence of a distinct trehalase having a rigid specificity for its substrate. By this method, trehalase activity was completely distinguishable from the activities of other alpha- and beta-glucosidases and beta-galactosidases. Localization data indicated that the enzyme diffused from intact grains and was probably soluble. The presence of its substrate could not be demonstrated in pollen or in stigmatic or stylar tissues.

Dissolution and ionization of sodium superoxide in sodium–oxygen batteries

PubMed Central

Kim, Jinsoo; Park, Hyeokjun; Lee, Byungju; Seong, Won Mo; Lim, Hee-Dae; Bae, Youngjoon; Kim, Haegyeom; Kim, Won Keun; Ryu, Kyoung Han; Kang, Kisuk

2016-01-01

With the demand for high-energy-storage devices, the rechargeable metal–oxygen battery has attracted attention recently. Sodium–oxygen batteries have been regarded as the most promising candidates because of their lower-charge overpotential compared with that of lithium–oxygen system. However, conflicting observations with different discharge products have inhibited the understanding of precise reactions in the battery. Here we demonstrate that the competition between the electrochemical and chemical reactions in sodium–oxygen batteries leads to the dissolution and ionization of sodium superoxide, liberating superoxide anion and triggering the formation of sodium peroxide dihydrate (Na2O2·2H2O). On the formation of Na2O2·2H2O, the charge overpotential of sodium–oxygen cells significantly increases. This verification addresses the origin of conflicting discharge products and overpotentials observed in sodium–oxygen systems. Our proposed model provides guidelines to help direct the reactions in sodium–oxygen batteries to achieve high efficiency and rechargeability. PMID:26892931

Effect of sintering on optical, structural and photoluminescence properties of ZnO thin films prepared by sol-gel process.

PubMed

Vishwas, M; Narasimha Rao, K; Arjuna Gowda, K V; Chakradhar, R P S

2010-09-15

Zinc oxide (ZnO) thin films have been deposited on glass substrates via sol-gel technique using zinc acetate dihydrate as precursor by spin coating of the sol at 2000 rpm. Effects of annealing temperature on optical, structural and photo luminescence properties of the deposited ZnO films have been investigated. The phase transition from amorphous to polycrystalline hexagonal wurtzite structure was observed at an annealing temperature of 400 degrees C. An average transmittance of 87% in the visible region has been obtained at room temperature. The optical transmittance has slightly increased with increase of annealing temperature. The band gap energy was estimated by Tauc's method and found to be 3.22 eV at room temperature. The optical band gap energy has decreased with increasing annealing temperature. The photoluminescence (PL) intensity increased with annealing temperature up to 200 degrees C and decreased at 300 degrees C. Copyright 2010 Elsevier B.V. All rights reserved.

Fabrication of calcium phosphate–calcium sulfate injectable bone substitute using hydroxy-propyl-methyl-cellulose and citric acid

PubMed Central

Thai, Van Viet

2010-01-01

In this study, an injectable bone substitute (IBS) consisting of citric acid, chitosan, and hydroxyl propyl methyl cellulose (HPMC) as the liquid phase and tetra calcium phosphate (TTCP), dicalcium phosphate dihydrate (DCPD) and calcium sulfate dehydrate (CSD, CaSO4·2H2O) powders as the solid phase, were fabricated. Two groups were classified based on the percent of citric acid in the liquid phase (20, 40 wt%). In each groups, the HPMC percentage was 0, 2, and 4 wt%. An increase in compressive strength due to changes in morphology was confirmed by scanning electron microscopy images. A good conversion rate of HAp at 20% citric acid was observed in the XRD profiles. In addition, HPMC was not obviously affected by apatite formation. However, both HPMC and citric acid increased the compressive strength of IBS. The maximum compressive strength for IBS was with 40% citric acid and 4% HPMC after 14 days of incubation in 100% humidity at 37°C. PMID:20333539

Elucidating the influence of polymorph-dependent interfacial solvent structuring at chitin surfaces.

PubMed

Brown, Aaron H; Walsh, Tiffany R

2016-10-20

Interfacial solvent structuring is thought to be influential in mediating the adsorption of biomolecules at aqueous materials interfaces. However, despite the enormous potential for exploitation of aqueous chitin interfaces in industrial, medical and drug-delivery applications, little is known at the molecular-level about such interfacial solvent structuring for chitin. Here we use molecular simulation to predict the structure of the [100] and [010] interfaces of α-chitin and β-chitin dihydrate in contact with liquid water and saline solution. We find the α-chitin [100] interface supports lateral high-density regions in the first water layer at the interface, which are also present, but not as pronounced, for β-chitin. The lateral structuring of interfacial ions at the saline/chitin interface is also more pronounced for α-chitin compared with β-chitin. Our findings provide a foundation for the systematic design of biomolecules with selective binding affinity for different chitin polymorphs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Tailoring the structure of biphasic calcium phosphate via synthesis procedure

NASA Astrophysics Data System (ADS)

Mansour, S. F.; El-dek, S. I.; Ahmed, M. K.

2017-12-01

Nano calcium phosphate ceramics (CaPC) were synthesized using simple co-precipitation method at different preparation conditions. The selected Ca/P ratio with a variation of pH value lead to formation of dicalcium phosphate dihydrate (DCPD) at pH 5 and 6 while, hydroxyapatite (HAP) nano particles were formed at pH 9 and 12 at room temperature. The crystallite size was in the range of 15-55 nm depending on the obtained crystalline phase. The study displayed variation of decomposition depending on the annealing temperature. The significant note is the different transformation trend of each phase depending on the starting pH value. The HRTEM illustrated that the DCPD phase was formed as fibers with diameter around 4-6 nm, while HAP was formed in rod shape. The aspect ratio decreased from 6.6 at pH 9 to 4 at pH 12 which refer to the great influence of pH value on the morphology of calcium phosphates.

Determination of residual fluoroquinolones in honey by liquid chromatography using metal chelate affinity chromatography.

PubMed

Yatsukawa, Yoh-Ichi; Ito, Hironobu; Matsuda, Takahiro; Nakamura, Munetomo; Watai, Masatoshi; Fujita, Kazuhiro

2011-01-01

A new analytical method for the simultaneous determination of seven fluoroquinolones, namely, norfloxacin, ciprofloxacin, danofloxacin, enrofloxacin, orbifloxacin, sarafloxacin, and difloxacin, especially in dark-colored honey, has been developed. Fluoroquinolone antibiotics were extracted from samples with MacIlvaine buffer solution (pH 4.0) containing EDTA disodium salt dihydrate. The extracts were treated with both a polymeric cartridge and a metal chelate affinity column preloaded with ferric ion (Fe3+). LC separation with fluorescence detection was performed at 40 degrees C using an Inertsil ODS-4 analytical column (150 x 4.6 mm, 3 microm). The mobile phase was composed of 20 mM/L citrate buffer solution (pH 3.1)-acetonitrile mixture (70 + 30, v/v) containing 1 mM/L sodium dodecyl sulfate. Lomefloxacin was used as an internal standard. The developed method was validated according to the criteria of European Commission Decision 2002/657/EC. Decision limits and detection capabilities were below 2.9 and 4.4 microg/kg, respectively.

Effect of interface voids on electroluminescence colors for ZnO microdisk/p-GaN heterojunction light-emitting diodes

NASA Astrophysics Data System (ADS)

Mo, Ran; Choi, Ji Eun; Kim, Hyeong Jin; Jeong, Junseok; Kim, Jong Chan; Kim, Yong-Jin; Jeong, Hu Young; Hong, Young Joon

2017-10-01

This study investigates the influence of voids on the electroluminescence (EL) emission color of ZnO microdisk/p-GaN heterojunction light-emitting diodes (LEDs). For this study, position-controlled microdisk arrays were fabricated on patterned p-GaN via wet chemical epitaxy of ZnO, and specifically, the use of trisodium citrate dihydrate (TCD) yielded high-density voids at the bottom of the microdisk. Greenish yellow or whitish blue EL was emitted from the microdisk LEDs formed with or without TCD, respectively, at reverse-bias voltages. Such different EL colors were found to be responsible for the relative EL intensity ratio between indigo and yellow emission peaks, which were originated from radiative recombination at p-GaN and ZnO, respectively. The relative EL intensity between dichromatic emissions is discussed in terms of (i) junction edge effect provoked by interfacial voids and (ii) electron tunneling probability depending on the depletion layer geometry.

Aquabis[1-hydroxy-2-(imidazol-3-ium-1-yl)-1,1′-ethylidenediphophonato-κ2 O,O′]zinc(II) dihydrate

PubMed Central

Freire, Eleonora; Vega, Daniel R.

2009-01-01

In the title complex, [Zn(C5H9NO7P2)2(H2O)]·2H2O, the zinc atom is coordinated by two zoledronate anions [zoledronate = (2-(1-imidazole)-1-hydr­oxy-1,1′-ethyl­idenediphophonate)] and one water mol­ecule. The coordination number is 5. There is one half-mol­ecule in the asymmetric unit, the zinc atom being located on a twofold rotation axis passing through the metal centre and the coordinating water O atom. The anion exists as a zwitterion with an overall charge of −1; the protonated nitro­gen in the ring has a positive charge and the two phospho­nates groups each have a single negative charge. Inter­molecular O—H⋯O hydrogen bonds link the mol­ecules. An N—H⋯O inter­action is also present. PMID:21578165

Exploration of the kinetic and thermochemical abilities for the free radical scavenging of two quercetin conformers

NASA Astrophysics Data System (ADS)

Mendoza-Wilson, Ana María; Sotelo-Mundo, Rogerio R.; Balandrán-Quintana, René R.; Glossman-Mitnik, Daniel; Sántiz-gómez, Marco a.; García-orozco, karina D.

2010-09-01

Quercetin has a great antioxidant potential due to its large capacity for free radical scavenging. Although it has been found that conformational changes have a profound effect on its chemical properties, there are few studies where conformation is associated with the antioxidant activity. The aim of this investigation was to explore the kinetic and the thermochemical abilities of two quercetin conformers for the free radical scavenging. Quercetin unhydrate (QUH) and quercetin dihydrate (QDH) conformers were studied employing 2,2-diphenyl-1-picrylhydrazyl (DPPH rad ) as in vitro radical model, and catechol and 4-hexyl-resorcinol as reference systems, for identifying the oxidation products. QDH showed to be most effective under conditions of free radical excess, while QUH was most effective when the flavonoid far exceeds the concentration of free radical. It was found, by means of experimental and computational methods, that 4'-OH, 3-OH and 3'-OH are the main reactive sites of both conformers.

Dissolution and ionization of sodium superoxide in sodium-oxygen batteries.

PubMed

Kim, Jinsoo; Park, Hyeokjun; Lee, Byungju; Seong, Won Mo; Lim, Hee-Dae; Bae, Youngjoon; Kim, Haegyeom; Kim, Won Keun; Ryu, Kyoung Han; Kang, Kisuk

2016-02-19

With the demand for high-energy-storage devices, the rechargeable metal-oxygen battery has attracted attention recently. Sodium-oxygen batteries have been regarded as the most promising candidates because of their lower-charge overpotential compared with that of lithium-oxygen system. However, conflicting observations with different discharge products have inhibited the understanding of precise reactions in the battery. Here we demonstrate that the competition between the electrochemical and chemical reactions in sodium-oxygen batteries leads to the dissolution and ionization of sodium superoxide, liberating superoxide anion and triggering the formation of sodium peroxide dihydrate (Na2O2·2H2O). On the formation of Na2O2·2H2O, the charge overpotential of sodium-oxygen cells significantly increases. This verification addresses the origin of conflicting discharge products and overpotentials observed in sodium-oxygen systems. Our proposed model provides guidelines to help direct the reactions in sodium-oxygen batteries to achieve high efficiency and rechargeability.

Renal geology (quantitative renal stone analysis) by 'Fourier transform infrared spectroscopy'.

PubMed

Singh, Iqbal

2008-01-01

To prospectively determine the precise stone composition (quantitative analysis) by using infrared spectroscopy in patients with urinary stone disease presenting to our clinic. To determine an ideal method for stone analysis suitable for use in a clinical setting. After routine and a detailed metabolic workup of all patients of urolithiasis, stone samples of 50 patients of urolithiasis satisfying the entry criteria were subjected to the Fourier transform infrared spectroscopic analysis after adequate sample homogenization at a single testing center. Calcium oxalate monohydrate and dihydrate stone mixture was most commonly encountered in 35 (71%) followed by calcium phosphate, carbonate apatite, magnesium ammonium hexahydrate and xanthine stones. Fourier transform infrared spectroscopy allows an accurate, reliable quantitative method of stone analysis. It also helps in maintaining a computerized large reference library. Knowledge of precise stone composition may allow the institution of appropriate prophylactic therapy despite the absence of any detectable metabolic abnormalities. This may prevent and or delay stone recurrence.

Enhancement of the antimicrobial properties of orthorhombic molybdenum trioxide by thermal induced fracturing of the hydrates.

PubMed

Shafaei, Shahram; Van Opdenbosch, Daniel; Fey, Tobias; Koch, Marcus; Kraus, Tobias; Guggenbichler, Josef Peter; Zollfrank, Cordt

2016-01-01

The oxides of the transition metal molybdenum exhibit excellent antimicrobial properties. We present the preparation of molybdenum trioxide dihydrate (MoO3 × 2H2O) by an acidification method and demonstrate the thermal phase development and morphological evolution during and after calcination from 25 °C to 600 °C. The thermal dehydration of the material was found to proceed in two steps. Microbiological roll-on tests using Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa were performed and exceptional antimicrobial activities were determined for anhydrous samples with orthorhombic lattice symmetry and a large specific surface area. The increase in the specific surface area is due to crack formation and to the loss of the hydrate water after calcination at 300 °C. The results support the proposed antimicrobial mechanism for transition metal oxides, which based on a local acidity increase as a consequence of the augmented specific surface area. Copyright © 2015 Elsevier B.V. All rights reserved.

Estimation of urinary stone composition by automated processing of CT images.

PubMed

Chevreau, Grégoire; Troccaz, Jocelyne; Conort, Pierre; Renard-Penna, Raphaëlle; Mallet, Alain; Daudon, Michel; Mozer, Pierre

2009-10-01

The objective of this article was developing an automated tool for routine clinical practice to estimate urinary stone composition from CT images based on the density of all constituent voxels. A total of 118 stones for which the composition had been determined by infrared spectroscopy were placed in a helical CT scanner. A standard acquisition, low-dose and high-dose acquisitions were performed. All voxels constituting each stone were automatically selected. A dissimilarity index evaluating variations of density around each voxel was created in order to minimize partial volume effects: stone composition was established on the basis of voxel density of homogeneous zones. Stone composition was determined in 52% of cases. Sensitivities for each compound were: uric acid: 65%, struvite: 19%, cystine: 78%, carbapatite: 33.5%, calcium oxalate dihydrate: 57%, calcium oxalate monohydrate: 66.5%, brushite: 75%. Low-dose acquisition did not lower the performances (P < 0.05). This entirely automated approach eliminates manual intervention on the images by the radiologist while providing identical performances including for low-dose protocols.

CROSS-DISCIPLINARY PHYSICS AND RELATED AREAS OF SCIENCE AND TECHNOLOGY: Effect of polyacrylamide on morphology and electromagnetic properties of chrysanthemum-like ZnO particles

NASA Astrophysics Data System (ADS)

Yan, Jun-Feng; Zhang, Zhi-Yong; You, Tian-Gui; Zhao, Wu; Yun, Jiang-Ni; Zhang, Fu-Chun

2009-10-01

Through hydrothermal process, the chrysanthemum-like ZnO particles are prepared with zinc acetate dihydrate (Zn(CH3COO)2·2H2O) and sodium hydroxide (NaOH) used as main resources under the different concentrations of surfactant polyacrylamide (PAM). The microstructure, morphology and the electromagnetic properties of the as-prepared products are characterized by high-resolution transmissïon electron microscopy (HRTEM), field emission environment scanning electron microscope (FEESEM) and microwave vector network analyzer, respectively. The experimental results indicate that the as-prepared products are ZnO single crystalline with hexagona wurtzite structure, that the values of slenderness ratio Ld are different in different PAM concentrations, and that the good magnetic loss property is found in the ZnO products, and the average magnetic loss tangent tan δu increases with PAM concentration increasing, while the dielectric loss tangent tan δe decreases.

Electrical and optical properties of p-type codoped ZnO thin films prepared by spin coating technique

NASA Astrophysics Data System (ADS)

Pathak, Trilok Kumar; Kumar, Vinod; Swart, H. C.; Purohit, L. P.

2016-03-01

Undoped, doped and codoped ZnO thin films were synthesized on glass substrates using a spin coating technique. Zinc acetate dihydrate, ammonium acetate and aluminum nitrate were used as precursor for zinc, nitrogen and aluminum, respectively. X-ray diffraction shows that the thin films have a hexagonal wurtzite structure for the undoped, doped and co-doped ZnO. The transmittance of the films was above 80% and the band gap of the film varied from 3.20 eV to 3.24 eV for undoped and doped ZnO. An energy band diagram to describe the photoluminescence from the thin films was also constructed. This diagram includes the various defect levels and possible quasi-Fermi levels. A minimum resistivity of 0.0834 Ω-cm was obtained for the N and Al codoped ZnO thin films with p-type carrier conductivity. These ZnO films can be used as a window layer in solar cells and in UV lasers.

MICROBIAL METABOLISM OF AROMATIC COMPOUNDS I.

PubMed Central

Tabak, Henry H.; Chambers, Cecil W.; Kabler, Paul W.

1964-01-01

Tabak, Henry H. (Robert A. Taft Sanitary Engineering Center, Cincinnati, Ohio), Cecil W. Chambers, and Paul W. Kabler. Microbial metabolism of aromatic carbon compounds. I. Decomposition of phenolic compounds and aromatic hydrocarbons by phenol-adapted bacteria. J. Bacteriol. 87:910–919. 1964.—Bacteria from soil and related environments were selected or adapted to metabolize phenol, hydroxy phenols, nitrophenols, chlorophenols, methylphenols, alkylphenols, and arylphenols when cultured in mineral salts media with the specific substrate as the sole source of carbon. A phenol-adapted culture (substrate-induced enzyme synthesis proven) was challenged in respirometric tests with 104 related compounds; probable significant oxidative activity occurred with 65. Dihydric phenols were generally oxidized; trihydric phenols were not. Cresols and dimethylphenols were oxidized; adding a chloro group increased resistance. Benzoic and hydroxybenzoic acids were oxidized; sulfonated, methoxylated, nitro, and chlorobenzoic acids were not; m-toluic acid was utilized but not the o- and p-isomers. Benzaldehyde and p-hydroxybenzaldehyde were oxidized. In general, nitro- and chloro-substituted compounds and the benzenes were difficult to oxidize. PMID:14137630

Dehydration of planetary ices at high pressure; the role of analogue materials (Invited)

NASA Astrophysics Data System (ADS)

Fortes, A. D.

2013-12-01

Many planet-forming compounds become unstable with respect to their components under conditions of high pressure. In the Earth, for example, Mg2SiO4 breaks down to MgSiO3 + MgO at ~ 25 GPa, a pressure corresponding to the 670 km seismic discontinuity, with significance for the dynamics of convective flow in the mantle. A similar phenomenon occurs with many hydrate compounds thought to be major ';rock forming minerals' inside outer Solar System bodies, undoubtedly with important consequences for the structure and dynamics of icy worlds. It is well known that clathrates tend to form denser polymorphs with an incrementally greater concentration of the guest molecule, exsolving high-pressure phases of water ice in the process, or else (in the case of CO2), break down to entirely to their component molecular solids. My own recent work using high-pressure neutron powder diffraction has explored not only the behaviour of methane clathrates but also the exsolution of water from ammonia dihydrate and monohydrate, both of which break down eventually to ammonia hemihydrate + ice. In some cases, understanding the sequence of changes in both crystal structure and composition at high pressure is challenging, particularly when the starting materials have a complex crystal structure. Some years ago, I identified a high-pressure phase boundary where MgSO4.11H2O (meridianiite) appeared to break down to another hydrate and high-pressure ice VI. However, the powder diffraction pattern of the hydrate formed under these conditions resembled nothing encountered previously in my high-pressure studies of the next lowest hydrate, MgSO4.7H2O (epsomite). This led me to search for hydration states between 7 and 11 which might have escaped detection over several centuries of study of simple divalent metal sulfates. A wide-ranging systematic study of M2+X6+O4.nH2O compounds at low temperatures uncovered two new hydrates, an 8-hydrate and a 9-hydrate, the former occurring only in NiSO4 solutions, and the latter being found in Ni-, Zn-, Cu-, and Fe-doped MgSO4 solutions. Indeed, I determined that small quantities of pure MgSO4.9H2O can co-crystallise at ambient pressure with meridianiite. However, these all appear to be metastable states, and further work was necessary to try and discover stable forms of these hydrates for further study. In experiments carried out earlier this year, evidence has emerged not only that MgMoO4 can form a (possibly) stable 8-hydrate but also that MgSeO4 can form a 9-hydrate that exists in equilibrium with liquid near the eutectic. These apparently esoteric compounds (from a planetary perspective) may yet hold the key to understanding the high-pressure behaviour of true planetary materials. Just as the search for analogue materials over many decades has substantially advanced our knowledge of Earth materials, similar analogue studies are poised to unlock the mysteries of these planetary ices.

Automated Leaf Tracking using Multi-view Image Sequences of Maize Plants for Leaf-growth Monitoring

NASA Astrophysics Data System (ADS)

Das Choudhury, S.; Awada, T.; Samal, A.; Stoerger, V.; Bashyam, S.

2017-12-01

Extraction of phenotypes with botanical importance by analyzing plant image sequences has the desirable advantages of non-destructive temporal phenotypic measurements of a large number of plants with little or no manual intervention in a relatively short period of time. The health of a plant is best interpreted by the emergence timing and temporal growth of individual leaves. For automated leaf growth monitoring, it is essential to track each leaf throughout the life cycle of the plant. Plants are constantly changing organisms with increasing complexity in architecture due to variations in self-occlusions and phyllotaxy, i.e., arrangements of leaves around the stem. The leaf cross-overs pose challenges to accurately track each leaf using single view image sequence. Thus, we introduce a novel automated leaf tracking algorithm using a graph theoretic approach by multi-view image sequence analysis based on the determination of leaf-tips and leaf-junctions in the 3D space. The basis of the leaf tracking algorithm is: the leaves emerge using bottom-up approach in the case of a maize plant, and the direction of leaf emergence strictly alternates in terms of direction. The algorithm involves labeling of the individual parts of a plant, i.e., leaves and stem, following graphical representation of the plant skeleton, i.e., one-pixel wide connected line obtained from the binary image. The length of the leaf is measured by the number of pixels in the leaf skeleton. To evaluate the performance of the algorithm, a benchmark dataset is indispensable. Thus, we publicly release University of Nebraska-Lincoln Component Plant Phenotyping dataset-2 (UNL-CPPD-2) consisting of images of the 20 maize plants captured by visible light camera of the Lemnatec Scanalyzer 3D high throughout plant phenotyping facility once daily for 60 days from 10 different views. The dataset is aimed to facilitate the development and evaluation of leaf tracking algorithms and their uniform comparisons.

Synthesis and Characterization of Diranitidinecopper(II) Sulfate Dihydrate

NASA Astrophysics Data System (ADS)

Syaima, H.; Rahardjo, S. B.; Zein, I. M.

2018-04-01

The complex of ranitidine with Cu(II) has been synthesized in 1:2-mole ratio of metal to the ligand in water. The forming of the complex was indicated by shifting of maximum wavelength from 816 nm (CuSO4·5H2O) to 626 nm (the complex). Infrared spectra indicated NO2 and NH functional group were coordinated to Cu(II). The percentage of copper in the complex measured by Atomic Absorption Spectroscopy (AAS) analysis was 7.5% indicating that formula of the complex was Cu(ranitidine)2SO4(H2O)n (n=2, 3 or 4). The electrical conductivity of Cu(II) complex in water was 71.0 Scm2mol-1 corresponding to 1:1 electrolytes. Thermogravimetric/Differential Thermal Analysis (TG/DTA) showed the presence of two molecules of H2O in the complex. UV-Vis spectra showed a transition peak on 15974 cm-1 indicating square planar geometry. The complex was paramagnetic with µeff 1.77 BM. The proposed formula of the complex was [Cu(ranitidine)2]SO4·2H2O.

Quantitative Mineralogical Composition of Calculi and Urine Abnormalities for Calcium Oxalate Stone Formers: A Single-Center Results.

PubMed

Kustov, Andrey V; Strelnikov, Alexander I

2018-05-03

The paper focuses on the relationship of risk factors and metabolic disorders with mineralogical composition of calculi, age and gender of calcium oxalate stone formers. Stone mineralogical composition, 24 hour biochemistry and pH-profile of urine were examined for sixty four stone formers using powder X-ray diffraction, spectrophotometric and potentiometric techniques. The analysis indicated that 44 % of calculi were composed of pure calcium oxalate monohydrate, whereas other 56 % contained both monohydrate and dihydrate or usually their mixtures with hydroxyl apatite. Hypocitraturia, hypercalciuria and hyperuricosuria were identified as the most frequent disorders. Patients with pure calcium oxalate stones and calcium oxalate mixed with apatite revealed different patterns including age, acid-base balance of urine, calcium, citrate excretion etc.Conclusions: Our results demonstrate that most patients simultaneously reveal several risk factors. The special attention should be paid to normalize the daily citrate, calcium and urate excretion. High risk patients, such as postmenopausal females or stone formers with a high apatite content require a specific metabolic evaluation towards in highlighting abnormalities associated with stone formation.

Solar-assisted synthesis of ZnO nanoparticles using lime juice: a green approach

NASA Astrophysics Data System (ADS)

Hinge, Shruti P.; Pandit, Aniruddha B.

2017-12-01

Zinc oxide (ZnO) nanoparticles are those nanoparticles which have been synthesized in various morphologies and shapes. Their size and shape dependent properties and their applications in vivid sectors of science and technology make them interesting to synthesize. Present work reports a green method for ZnO nanoparticle synthesis using lime juice and sunlight. ZnO nanoparticles were also synthesized by conventionally used methods like heating, stirring or no heating and/or stirring. The nanoparticles were characterized using different techniques like UV-vis spectroscopy, scanning electron microscopy (SEM), x-ray diffraction (XRD) and dynamic light scattering (DLS). Thermo gravimetric analysis (TGA) was also carried out for the intermediate product to select the calcination temperature. Stoichiometric study reveals that the intermediate product formed is zinc citrate dihydrate. The synthesized calcined nanoparticles have good crystallinity, uniform shape, and high purity and were in the size range of 20-30 nm. These nanoparticles formed agglomerates of various shapes in the size range of 200-750 nm. This process is ecofriendly and is amiable for easy scale up.

Predicting the quality of powders for inhalation from surface energy and area.

PubMed

Cline, David; Dalby, Richard

2002-09-01

To correlate the surface energy of active and carrier components in an aerosol powder to in vitro performance of a passive dry powder inhaler. Inverse gas chromatography (IGC) was used to assess the surface energy of active (albuterol and ipratropium bromide) and carrier (lactose monohydrate, trehalose dihydrate and mannitol) components of a dry powder inhaler formulation. Blends (1%w/w) of drug and carrier were prepared and evaluated for dry powder inhaler performance by cascade impaction. The formulations were tested with either of two passive dry powder inhalers, Rotahaler (GlaxoSmithKline) or Handihaler (Boehringer Ingelheim). In vitro performance of the powder blends was strongly correlated to surface energy interaction between active and carrier components. Plotting fine particle fraction vs. surface energy interaction yielded an R2 value of 0.9283. Increasing surface energy interaction between drug and carrier resulted in greater fine particle fraction of drug. A convincing relationship, potentially useful for rapid formulation design and screening, was found between the surface energy and area parameters derived from IGC and dry powder inhaler performance.

Variations in the Infrared Spectra of Wüstite with Defects and Disorder

NASA Astrophysics Data System (ADS)

Koike, C.; Matsuno, J.; Chihara, H.

2017-08-01

The presence of FeO particles in circumstellar space has been suggested based on the observation of a mysterious 21 μm emission band. However, the complete infrared spectra of FeO have not been obtained so far; hence, data of the infrared (IR) spectra of FeO need to be investigated. We prepared synthetic and commercial samples of FeO, which were obtained by crushing bulk samples, annealing iron oxalate dihydrate ({{FeC}}2{{{O}}}4\\cdot 2{{{H}}}2{{O}}), and mechanical milling of a powder mixture comprising (Fe and {{Fe}}2{{{O}}}3) particles with different milling times. We present a new study on the IR spectra of these samples, and show that these spectra changed according to defects and disorders. Furthermore, FeO particles are very sensitive to oxygen fugacity and temperature. The spectra of FeO particles were compared with the unidentified observed feature. It may be difficult for FeO particles to exist alone in the ISM and circumstellar space. This may be connected to the problem of missing iron in the ISM.

Determination of nitric oxide mediating intracellular Ca2+ release on neurons based on confocal microscopy imaging

NASA Astrophysics Data System (ADS)

Zheng, Liqin; Wang, Yuhua; He, Yipeng; Zeng, Yixiu; Zhang, Yanding; Xie, Shusen

2014-09-01

The gas NO is a ubiquitous intercellular messenger that modulates a wide range of physiological and pathophysiological functions. But few studies were made to study the role of NO in the Ca2+ release in dorsal root ganglion (DRG) neurons by confocal microscopy. Thus the objective of this study was to assess if NO has a role in Ca2+ signaling in DRG neurons using confocal microscopy combined with special fluorescence probe Fluo-3/AM. A 100 μM concentration of the NO donors (Sodium Nitroprusside, Dihydrate, SNP) and NO synthase inhibitor (NG-Monomethyl-L-arginine, Monoacetate salt, L-NMMA) was used in the study. Results showed that the fluorescence intensity increased rapidly after injecting SNP, which indicated that SNP could enhance intracellular Ca2+ release. And the fluorescence intensity shrank gradually with time and kept at a low level for quite a long period after loading with L-NMMA which indicated that L-NMMA could block intracellular Ca2+ release. All these results demonstrated that NO was involved in the regulation of intracellular Ca2+ release in the DRG neurons.

Phase transformation of calcium oxalate dihydrate-monohydrate: Effects of relative humidity and new spectroscopic data

NASA Astrophysics Data System (ADS)

Conti, Claudia; Casati, Marco; Colombo, Chiara; Realini, Marco; Brambilla, Luigi; Zerbi, Giuseppe

2014-07-01

New data on vibrational properties of calcium oxalates and their controversial transformation mechanism are presented. We have focused on whewellite (CaC2O4·H2O) and weddellite [CaC2O4·(2 + x) H2O], the most common phases of calcium oxalate; these compounds occur in many organisms, in kidney stones and in particular kinds of films found on the surface of many works of art. Low temperature experiments carried out by Fourier transform infrared spectroscopy have highlighted both the high structural order in the crystalline state of whewellite and the disordered distribution of the zeolitic water molecules in weddellite. The synthesised nanocrystals of weddellite have been kept under different hygrometric conditions in order to study, by X-ray powder diffraction, the role of “external” water molecules on their stability. Moreover, in order to identify the different kinds of water molecules, a re-investigation, supported by quantum chemical calculations, of the observed vibrational spectra (IR and Raman) of whewellite has been conducted.

[Quantitative mineralogical analyzes of kidney stones and diagnosing metabolic disorders in female patients with calcium oxalate urolithiasis].

PubMed

Kustov, A V; Moryganov, M A; Strel'nikov, A I; Zhuravleva, N I; Airapetyan, A O

2016-02-01

To conduct a complex examination of female patients with calcium oxalate urolithiasis to detect metabolic disorders, leading to stone formation. The study was carried out using complex physical and chemical methods, including quantitative X-ray phase analysis of urinary stones, pH measurement, volumetry, urine and blood spectrophotometry. Quantitative mineralogical composition of stones, daily urine pH profile, daily urinary excretion of ions of calcium, magnesium, oxalate, phosphate, citrate and uric acid were determined in 20 female patients with calcium oxalate stones. We have shown that most of the stones comprised calcium oxalate monohydrate or mixtures of calcium oxalate dihydrate and hydroxyapatite. Among the identified abnormalities, the most frequent were hypocitraturia and hypercalciuria - 90 and 45%, respectively. Our findings revealed that the daily secretion of citrate and oxalate in patients older than 50 years was significantly lower than in younger patients. In conclusion, daily urinary citrate excretion should be measured in female patients with calcium oxalate stones. This is necessary both to determine the causes of stone formation, and to monitor the effectiveness of citrate therapy.

Diatom frustules decorated with zinc oxide nanoparticles for enhanced optical properties

NASA Astrophysics Data System (ADS)

Lamastra, F. R.; Grilli, M. L.; Leahu, G.; Belardini, A.; Li Voti, R.; Sibilia, C.; Salvatori, D.; Cacciotti, I.; Nanni, F.

2017-09-01

Zinc oxide (ZnO) nanoparticles were synthesized on diatomite (DE) surface by a low temperature sol gel technique, starting from zinc acetate dihydrate (Zn(CH3COO)2 · 2H2O) solution in water/ethyl alcohol, in presence of triethanolamine (TEA) with functions of Zn2+ chelating agent, catalyst and mediator of nanoparticle growth on DE surface. Microstructural features were investigated by field emission scanning electron microscopy and x-ray diffraction. ZnO crystalline nanoparticles, well distributed both on the surface and into the porous architecture of diatomite, were obtained just after the synthesis carried out at 80 °C without the need of calcination treatments. The optical properties of ZnO/DE hybrid powders were measured for the first time by means of photoacoustic spectroscopy (PAS). A new method to retrieve both the optical absorption and scattering coefficients from PAS is here discussed for powder aggregates. The fingerprint of the zinc oxide nanoparticles has been highlighted in the Mie scattering resonance in the UV-Vis range, and in the enhancement of the optical absorption with respect to diatomite.

High-Content Screening in hPSC-Neural Progenitors Identifies Drug Candidates that Inhibit Zika Virus Infection in Fetal-like Organoids and Adult Brain.

PubMed

Zhou, Ting; Tan, Lei; Cederquist, Gustav Y; Fan, Yujie; Hartley, Brigham J; Mukherjee, Suranjit; Tomishima, Mark; Brennand, Kristen J; Zhang, Qisheng; Schwartz, Robert E; Evans, Todd; Studer, Lorenz; Chen, Shuibing

2017-08-03

Zika virus (ZIKV) infects fetal and adult human brain and is associated with serious neurological complications. To date, no therapeutic treatment is available to treat ZIKV-infected patients. We performed a high-content chemical screen using human pluripotent stem cell-derived cortical neural progenitor cells (hNPCs) and found that hippeastrine hydrobromide (HH) and amodiaquine dihydrochloride dihydrate (AQ) can inhibit ZIKV infection in hNPCs. Further validation showed that HH also rescues ZIKV-induced growth and differentiation defects in hNPCs and human fetal-like forebrain organoids. Finally, HH and AQ inhibit ZIKV infection in adult mouse brain in vivo. Strikingly, HH suppresses viral propagation when administered to adult mice with active ZIKV infection, highlighting its therapeutic potential. Our approach highlights the power of stem cell-based screens and validation in human forebrain organoids and mouse models in identifying drug candidates for treating ZIKV infection and related neurological complications in fetal and adult patients. Copyright © 2017 Elsevier Inc. All rights reserved.

Antimicrobial activity of biopolymeric thin films containing flavonoid natural compounds and silver nanoparticles fabricated by MAPLE: A comparative study

NASA Astrophysics Data System (ADS)

Cristescu, R.; Visan, A.; Socol, G.; Surdu, A. V.; Oprea, A. E.; Grumezescu, A. M.; Chifiriuc, M. C.; Boehm, R. D.; Yamaleyeva, D.; Taylor, M.; Narayan, R. J.; Chrisey, D. B.

2016-06-01

The purpose of this study was to investigate the interactions between microorganisms, including the planktonic and adherent organisms, and biopolymer (polyvinylpyrrolidone), flavonoid (quercetin dihydrate and resveratrol)-biopolymer, and silver nanoparticles-biopolymer composite thin films that were deposited using matrix assisted pulsed laser evaporation (MAPLE). A pulsed KrF* excimer laser source was used to deposit the aforementioned composite thin films, which were characterized using Fourier transform infrared spectroscopy (FT-IR), infrared microscopy (IRM), scanning electron microscopy (SEM), Grazing incidence X-ray diffraction (GIXRD) and atomic force microscopy (AFM). The antimicrobial activity of thin films was quantified using an adapted disk diffusion assay against Gram-positive and Gram-negative bacteria strains. FT-IR, AFM and SEM studies confirmed that MAPLE may be used to fabricate thin films with chemical properties corresponding to the input materials as well as surface properties that are appropriate for medical use. The silver nanoparticles and flavonoid-containing films exhibited an antimicrobial activity both against Gram-positive and Gram-negative bacterial strains demonstrating the potential use of these hybrid systems for the development of novel antimicrobial strategies.

Effects of optical band gap energy, band tail energy and particle shape on photocatalytic activities of different ZnO nanostructures prepared by a hydrothermal method

NASA Astrophysics Data System (ADS)

Klubnuan, Sarunya; Suwanboon, Sumetha; Amornpitoksuk, Pongsaton

2016-03-01

The dependence of the crystallite size and the band tail energy on the optical properties, particle shape and oxygen vacancy of different ZnO nanostructures to catalyse photocatalytic degradation was investigated. The ZnO nanoplatelets and mesh-like ZnO lamellae were synthesized from the PEO19-b-PPO3 modified zinc acetate dihydrate using aqueous KOH and CO(NH2)2 solutions, respectively via a hydrothermal method. The band tail energy of the ZnO nanostructures had more influence on the band gap energy than the crystallite size. The photocatalytic degradation of methylene blue increased as a function of the irradiation time, the amount of oxygen vacancy and the intensity of the (0 0 0 2) plane. The ZnO nanoplatelets exhibited a better photocatalytic degradation of methylene blue than the mesh-like ZnO lamellae due to the migration of the photoelectrons and holes to the (0 0 0 1) and (0 0 0 -1) planes, respectively under the internal electric field, that resulted in the enhancement of the photocatalytic activities.

Evaluation of four biodegradable, injectable bone cements in an experimental drill hole model in sheep.

PubMed

von Rechenberg, Brigitte; Génot, Oliver R; Nuss, Katja; Galuppo, Larry; Fulmer, Mark; Jacobson, Evan; Kronen, Peter; Zlinszky, Kati; Auer, Jörg A

2013-09-01

Four cement applications were tested in this investigation. Two dicalcium phosphate dihydrate (DCPD-brushite) hydraulic cements, an apatite hydraulic fiber loaded cement, and a calcium sulfate cement (Plaster of Paris) were implanted in epiphyseal and metaphyseal cylindrical bone defects in sheep. The in vivo study was performed to assess the biocompatibility and bone remodeling of four cement formulations. After time periods of 2, 4, and 6 months, the cement samples were clinically and histologically evaluated. Histomorphometrically, the amount of new bone formation, fibrous tissue, and bone marrow and the area of remaining cement were measured. In all specimens, no signs of inflammation were detectable either macroscopically or microscopically. Cements differed mainly in their resorption time. Calcium sulfate was already completely resorbed at 2 months and showed a variable amount of new bone formation and/or fibrous tissue in the original drill hole over all time periods. The two DCPD cements in contrast were degraded to a large amount at 6 months, whereas the apatite was almost unchanged over all time periods. Copyright © 2013. Published by Elsevier B.V.

4,4'-([4,4'-Bipyridine]-1,1'-diium-1,1'-diyl)dibenzoate dihydrate

DOE PAGES

Rodriguez, Mark A.; Sava Gallis, Dorina F.; Chavez, James S.; ...

2016-06-01

We report here the synthesis of a neutral viologen derivative, C 24H 16N 2O 4·2H 2O. The non-solvent portion of the structure (Z-Lig) is a zwitterion, consisting of two positively charged pyridinium cations and two negatively charged carboxylate anions. The carboxylate group is almost coplanar [dihedral angle = 2.04 (11)°] with the benzene ring, whereas the dihedral angle between pyridine and benzene rings is 46.28 (5)°. TheZ-Lig molecule is positioned on a center of inversion (Fig. 1). The presence of the twofold axis perpendicular to thec-glide plane in space groupC2/c generates a screw-axis parallel to thebaxis that is shifted from themore » origin by 1/4 in theaandcdirections. This screw-axis replicates the molecule (and solvent water molecules) through space. TheZ-Lig molecule links to adjacent moleculesviaO—H...O hydrogen bonds involving solvent water molecules as well as intermolecular C—H...O interactions. There are also π–π interactions between benzene rings on adjacent molecules.« less

Estimated congener specific gas-phase atmospheric behavior and fractionation of perfluoroalkyl compounds: rates of reaction with atmospheric oxidants, air-water partitioning, and wet/dry deposition lifetimes.

PubMed

Rayne, Sierra; Forest, Kaya; Friesen, Ken J

2009-08-01

A quantitative structure-activity model has been validated for estimating congener specific gas-phase hydroxyl radical reaction rates for perfluoroalkyl sulfonic acids (PFSAs), carboxylic acids (PFCAs), aldehydes (PFAls) and dihydrates, fluorotelomer olefins (FTOls), alcohols (FTOHs), aldehydes (FTAls), and acids (FTAcs), and sulfonamides (SAs), sulfonamidoethanols (SEs), and sulfonamido carboxylic acids (SAAs), and their alkylated derivatives based on calculated semi-empirical PM6 method ionization potentials. Corresponding gas-phase reaction rates with nitrate radicals and ozone have also been estimated using the computationally derived ionization potentials. Henry's law constants for these classes of perfluorinated compounds also appear to be reasonably approximated by the SPARC software program, thereby allowing estimation of wet and dry atmospheric deposition rates. Both congener specific gas-phase atmospheric and air-water interface fractionation of these compounds is expected, complicating current source apportionment perspectives and necessitating integration of such differential partitioning influences into future multimedia models. The findings will allow development and refinement of more accurate and detailed local through global scale atmospheric models for the atmospheric fate of perfluoroalkyl compounds.

Speciation in experimental C-O-H fluids produced by the thermal dissociation of oxalic acid dihydrate

NASA Astrophysics Data System (ADS)

Morgan, G. B., VI; Chou, I.-Ming; Pasteris, J. D.

1992-01-01

Fluid speciations and their related reaction pathways were studied in C-O-H-system fluids produced by the thermal dissociation of oxalic acid dihydrate (OAD: H 2C 2O 4 · 2H 2O) sealed in silica glass capsules. Experiments were conducted in the temperature range 230-750°C, with bulk fluid densities in the range 0.01-0.53 g/cm 3. Pressure was controlled by temperature and density in the isochoric systems. The quenched products of dissociation experiments were an aqueous liquid and one (supercritical fluid) or, rarely, two (vapor plus liquid) carbonic phase (s). In-situ Raman microanalyses were performed on the quenched carbonic phases at room temperature, at which fluid pressures ranged from about 50 to 340 bars. Bulk fluid speciations were reconstructed from the Raman analyses via mass balance constraints, and appear to monitor the true fluid speciations at run conditions. In experiments from the lowtemperature range (230-350°C), fluid speciations record the dissociation of OAD according to the reaction OAD = CO2 + CO + 3 H2O. A process of the form CO + H2O = CO2 + H2 is driven to the right with increasing temperature. The hydrogen gas produced tends to escape from the sample systems via diffusion into/through the silica glass capsules, shifting bulk compositions toward equimolar binary H 2O-CO 2 mixtures. The speciations of fluids in experiments with minimal hydrogen loss show poor agreement with speciations calculated for equilibrium fluids by the corresponding-states model of SAXENA and FEI (1988). Such disagreement suggests that the formations of CH 4 and graphite are metastably inhibited in the current experiments, which correlates with their absence or trivial abundances in experimental products. Moreover, calculations in which the stabilities of methane and graphite are suppressed suggest that such metastable equilibrium is approached only in experiments at temperatures greater than about 600-650°C. These results have applications to fluid processes in geological environments, in addition to considerations of using oxalate compounds as volatile sources in experimental studies. It is possible that disequilibrium or metastable fluids may be entrapped as inclusions; re-speciation (toward metastable or stable equilibrium) during P-T evolution of a given terrain would place the fluid inclusion on a new isochore that would not project through the original conditions of entrapment. Moreover, the disequilibrium to metastable nature of dissociation reactions, coupled with the diffusional mobility of hydrogen gas observed in the current experiments, suggests that the predominance of binary H 2O-CO 2 fluid mixtures in natural inclusions from medium- to high-grade metamorphic terrains may be more than a coincidence of similar initial bulk compositions.

Speciation in experimental C-O-H fluids produced by the thermal dissociation of oxalic acid dihydrate

USGS Publications Warehouse

Morgan, G.B.; Chou, I.-Ming; Pasteris, J.D.

1992-01-01

Fluid speciations and their related reaction pathways were studied in C-O-H-system fluids produced by the thermal dissociation of oxalic acid dihydrate (OAD: H2C2O4 ?? 2H2O) sealed in silica glass capsules. Experiments were conducted in the temperature range 230-750??C, with bulk fluid densities in the range 0.01-0.53 g/cm3. Pressure was controlled by temperature and density in the isochoric systems. The quenched products of dissociation experiments were an aqueous liquid and one (supercritical fluid) or, rarely, two (vapor plus liquid) carbonic phase (s). In-situ Raman microanalyses were performed on the quenched carbonic phases at room temperature, at which fluid pressures ranged from about 50 to 340 bars. Bulk fluid speciations were reconstructed from the Raman analyses via mass balance constraints, and appear to monitor the true fluid speciations at run conditions. In experiments from the lowtemperature range (230-350??C), fluid speciations record the dissociation of OAD according to the reaction OAD = CO2 + CO + 3H2O. A process of the form CO + H2O = CO2 + H2 is driven to the right with increasing temperature. The hydrogen gas produced tends to escape from the sample systems via diffusion into/through the silica glass capsules, shifting bulk compositions toward equimolar binary H2O-CO2 mixtures. The speciations of fluids in experiments with minimal hydrogen loss show poor agreement with speciations calculated for equilibrium fluids by the corresponding-states model of Saxena and Fei (1988). Such disagreement suggests that the formations of CH4 and graphite are metastably inhibited in the current experiments, which correlates with their absence or trivial abundances in experimental products. Moreover, calculations in which the stabilities of methane and graphite are suppressed suggest that such metastable equilibrium is approached only in experiments at temperatures greater than about 600-650??C. These results have applications to fluid processes in geological environments, in addition to considerations of using oxalate compounds as volatile sources in experimental studies. It is possible that disequilibrium or metastable fluids may be entrapped as inclusions; re-speciation (toward metastable or stable equilibrium) during P-T evolution of a given terrain would place the fluid inclusion on a new isochore that would not project through the original conditions of entrapment. Moreover, the disequilibrium to metastable nature of dissociation reactions, coupled with the diffusional mobility of hydrogen gas observed in the current experiments, suggests that the predominance of binary H2O-CO2 fluid mixtures in natural inclusions from medium- to high-grade metamorphic terrains may be more than a coincidence of similar initial bulk compositions. ?? 1992.

Structural, thermal, and magnetic study of solvation processes in spin-crossover [Fe(bpp)(2)][Cr(L)(ox)(2)](2).nH(2)O complexes.

PubMed

Clemente-León, Miguel; Coronado, Eugenio; Giménez-López, M Carmen; Romero, Francisco M

2007-12-24

The influence of lattice water in the magnetic properties of spin-crossover [Fe(bpp)2]X2.nH2O salts [bpp = 2,6-bis(pyrazol-3-yl)pyridine] is well-documented. In most cases, it stabilizes the low-spin state compared to the anhydrous compound. In other cases, it is rather the contrary. Unraveling this mystery implies the study of the microscopic changes that accompany the loss of water. This might be difficult from an experimental point of view. Our strategy is to focus on some salts that undergo a nonreversible dehydration-hydration process without loss of crystallinity. By comparison of the structural and magnetic properties of original and rehydrated samples, several rules concerning the role of water at the microscopic level can be deduced. This paper reports on the crystal structure, thermal studies, and magnetic properties of [Fe(bpp)2][Cr(bpy)(ox)2]2.2H2O (1), [Fe(bpp)2][Cr(phen)(ox)2]2.0.5H2O.0.5MeOH (2), and [Fe(bpp)2][Cr(phen)(ox)2]2.5.5H2O.2.5MeOH (3). Salt 1 contains both high-spin (HS) and low-spin (LS) Fe2+ cations in a 1:1 ratio. Dehydration yields the anhydrous spin-crossover compound with T1/2 downward arrow = 353 K and T1/2 upward arrow = 369 K. Rehydration affords the dihydrate [Fe(bpp)2][Cr(bpy)(ox)2]2.2H2O (1r) with 100% HS Fe2+ sites. Salt 2 also contains both HS and LS Fe2+ cations in a 1:1 ratio. Dehydration yields the anhydrous spin-crossover compound with T1/2 downward arrow = 343 K and T1/2 upward arrow = 348 K. Rehydration affords [Fe(bpp)2][Cr(phen)(ox)2]2.0.5H2O (2r) with 72% Fe2+ sites in the LS configuration. The structural, magnetic, and thermal properties of these rehydrated compounds 1r and 2r are also discussed. Finally, 1 has been dehydrated and resolvated with MeOH to give [Fe(bpp)2][Cr(bpy)(ox)2]2.MeOH (1s) with 33% HS Fe2+ sites. The influence of the guest solvent in the Fe2+ spin state can anticipate the future applications of these compounds in solvent sensing.

Atomically resolved calcium phosphate coating on a gold substrate.

PubMed

Metoki, Noah; Baik, Sung-Il; Isheim, Dieter; Mandler, Daniel; Seidman, David N; Eliaz, Noam

2018-05-10

Some articles have revealed that the electrodeposition of calcium phosphate (CaP) coatings entails a precursor phase, similarly to biomineralization in vivo. The chemical composition of the initial layer and its thickness are, however, still arguable, to the best of our knowledge. Moreover, while CaP and electrodeposition of metal coatings have been studied utilizing atom-probe tomography (APT), the electrodeposition of CaP ceramics has not been heretofore studied. Herein, we present an investigation of the CaP deposition on a gold substrate. Using APT and transmission electron microscopy (TEM) it is found that a mixture of phases, which could serve as transient precursor phases to hydroxyapatite (HAp), can be detected. The thickness of these phases is tens of nanometers, and they consist of amorphous CaP (ACP), dibasic calcium phosphate dihydrate (DCPD), and octacalcium phosphate (OCP). This demonstrates the value of using atomic-resolved characterization techniques for identifying the precursor phases. It also indicates that the kinetics of their transformation into the more stable HAp is not too fast to enable their observation. The coating gradually displays higher Ca/P atomic ratios, a porous nature, and concomitantly a change in its density.

Fourier Transform Infrared Analysis of Urinary Calculi and Metabolic Studies in a Group of Sicilian Children.

PubMed

D'Alessandro, Maria Michela; Gennaro, Giuseppe; Tralongo, Pietro; Maringhini, Silvio

2017-05-01

Prevalence of urinary calculi in children has been increasing in the past years. We performed an analysis of the chemical composition of stones formers of the pediatric population in our geographical area over the years 2005 to 2013. Fourier transform infrared spectroscopy was employed for the determination of the calculus composition of a group of Sicilian children, and metabolic studies were performed to formulate the correct diagnosis and establish therapy. The prevalence of stone formation was much higher for boys than for girls, with a sex ratio of 1.9:1. The single most frequent component was found to be calcium oxalate monohydrate, and calcium oxalates (pure or mixed calculi) were the overall most frequent components. Calcium phosphates ranked 2nd for frequency, most often in mixed calculi, while urates ranked 3rd. The metabolic disorder most often associated with pure calcium oxalate monohydrate calculi was hypocitraturia, while hyperoxaluria was predominantly associated with calcium oxalate dihydrate calculi. Mixed calculi had the highest prevalence in our pediatric population. Our data showed that Fourier transform infrared spectroscopy was a useful tool for the determination of the calculi composition.

Flexocoupling-induced soft acoustic modes and the spatially modulated phases in ferroelectrics

NASA Astrophysics Data System (ADS)

Morozovska, Anna N.; Glinchuk, Maya D.; Eliseev, Eugene A.; Vysochanskii, Yulian M.

2017-09-01

Using the Landau-Ginzburg-Devonshire theory and one component approximation, we examined the conditions of the soft acoustic phonon mode (A-mode) appearance in a ferroelectric (FE) depending on the magnitude of the flexoelectric coefficient f and temperature T . If the flexocoefficient f is equal to the temperature-dependent critical value fcr(T ) at some temperature T =TIC , the A-mode frequency tends to zero at wave vector k =k0cr , and the spontaneous polarization becomes spatially modulated in the temperature range T fcr(TIC) , the A-mode becomes zero for two wave vectors k =k1,2 cr , and does not exist in the range of wave vectors k1cr

Investigation of microstructure and mechanical properties of phosphocalcic bone substitute using the chemical wet method

NASA Astrophysics Data System (ADS)

Alimi, Latifa; Bahloul, Lynda; Azzi, Afef; Guerfi, Souad; Ismail, Fadhel; Chaoui, Kamel

2018-05-01

Selection of calcium phosphate base materials in reconstructive bone surgery is justified by the surprising similarities in chemical compositions with human bones. The closest to natural apatite material is the hydroxyapatite (HAp) which has a chemical composition based on calcium and phosphate (Ca10(PO4)6(OH)2). In this study, HAp is synthesized using the wet precipitation method from hydrated calcium chloride (CaCl2,12H2O) and di-sodium hydrogen phosphate di-hydrate (HNa2PO4,2H2O). The powder is calcinated at 900°C and 1200°C in order to compare with sintered condition at 1150°C. Vickers microhardness tests and X-ray diffraction analyzes are used for the characterization of the crystalline material. Mechanical properties (Hv, σe, σr, and KC) and the degree of crystallinity (Xc) are discussed according to heat treatment temperatures. Results indicate that heat treating the powder at 1200°C increased crystallinity up to 72%. At the same time, microhardness increased with temperature and even outmatched the sintered case at 1150°C. Fracture toughness is ameliorated with increasing heat treatment temperature by more than two folds.

Investigation of the effect of hydroxypropyl methylcellulose on the phase transformation and release profiles of carbamazepine-nicotinamide cocrystal.

PubMed

Li, Mingzhong; Qiu, Shi; Lu, Yan; Wang, Ke; Lai, Xiaojun; Rehan, Mohammad

2014-09-01

The aim of this work was to investigate the influence of hydroxypropyl methylcellulose (HPMC) on the phase transformation and release profile of carbamazepine-nicotinamide (CBZ-NIC) cocrystal in solution and in sustained release matrix tablets. The polymorphic transitions of the CBZ-NIC cocrystal and its crystalline properties were examined by differential scanning calorimetry (DSC), X-ray powder diffraction (XRPD), Raman spectroscopy, and scanning electron microscopy (SEM). The apparent CBZ solubility and dissolution rate of CBZ-NIC cocrystal were constant in different concentrations of HPMC solutions. In a lower percentage of HPMC in the matrix tablets, the CBZ release profile of the CBZ-NIC cocrystal was nonlinear and declined over time. With an increased HPMC content in the tablets, the CBZ-NIC cocrystal formulation showed a significantly higher CBZ release rate in comparison with the other two formulations of CBZ III and the physical mixture. Because of a significantly improved dissolution rate of the CBZ-NIC cocrystal, the rate of CBZ entering into solution is significantly faster than the rate of formation of the CBZ-HPMC soluble complex in solution, leading to a higher supersaturation level of CBZ and subsequently precipitation of CBZ dihydrate.

Initial dissolution kinetics of cocrystal of carbamazepine with nicotinamide.

PubMed

Hattori, Yusuke; Sato, Maiko; Otsuka, Makoto

2015-11-01

Objectives of this study are investigating the initial dissolution kinetics of the cocrystal of carbamazepine (CBZ) with nicotinamide (NIC) and understanding its initial dissolution process. Cocrystal solids of CBZ with NIC were prepared by co-milling and solvent evaporation methods. The formation of cocrystal solid was verified via X-ray diffraction measurement. Dissolution tests of the solids were performed using an original flow cell and ultraviolet-visible spectroscopic detector. The spectra monitored in situ were analyzed to determine the dissolved compounds separately using the classical least squares regression method. The initial dissolution profiles were interpreted using simultaneous model of dissolution and phase changes. In the initial dissolution, CBZ in the cocrystal structure dissolved in water and it was suggested that CBZ reached a metastable intermediate state simultaneously with dissolution. The cocrystal solid prepared by solvent evaporation provided a higher rate constant of the phase change than that prepared by co-milling. Our results thus support the use of evaporation as the method of choice to produce ordered cocrystal structures. We suggest that CBZ forms dihydrate during the dissolution process; however, during the initial phase of dissolution, CBZ changes to a metastable intermediate phase. © 2015 Royal Pharmaceutical Society.

Optical and structural properties of Al-doped ZnO thin films by sol gel process.

PubMed

Jun, Min-Chul; Koh, Jung-Hyuk

2013-05-01

Transparent conducting oxide (TCO) materials with high transmittance and good electrical conductivity have been attracted much attention due to the development of electronic display and devices such as organic light emitting diodes (OLEDs), and dye-sensitized solar cells (DSSCs). Aluminum doped zinc oxide thin films (AZO) have been well known for their use as TCO materials due to its stability, cost-effectiveness, good optical transmittance and electrical properties. Especially, AZO thin film, which have low resistivity of 2-4 x 10(-4) omega x cm which is similar to that of ITO films with wide band gap semiconductors. The AZO thin films were deposited on glass substrates by sol-gel spin-coating process. As a starting material, zinc acetate dihydrate (Zn(CH3COO)2 x 2H2O) and aluminum chloride hexahydrate (AlCl3 6H2O) were used. 2-methoxyethanol and monoethanolamine (MEA) were used as solvent and stabilizer, respectively. After deposited, the films were preheated at 300 degrees C on a hotplate and post-heated at 650 degrees C for 1.5 hrs in the furnace. We have studied the structural and optical properties as a function of Al concentration (0-2.5 mol.%).

Effect of repeated compaction of tablets on tablet properties and work of compaction using an instrumented laboratory tablet press.

PubMed

Gamlen, Michael John Desmond; Martini, Luigi G; Al Obaidy, Kais G

2015-01-01

The repeated compaction of Avicel PH101, dicalcium phosphate dihydrate (DCP) powder, 50:50 DCP/Avicel PH101 and Starch 1500 was studied using an instrumented laboratory tablet press which measures upper punch force, punch displacement and ejection force and operates using a V-shaped compression profile. The measurement of work compaction was demonstrated, and the test materials were ranked in order of compaction behaviour Avicel PH101 > DCP/Avicel PH101 > Starch > DCP. The behaviour of the DCP/Avicel PH101 mixture was distinctly non-linear compared with the pure components. Repeated compaction and precompression had no effect on the tensile fracture strength of Avicel PH101 tablets, although small effects on friability and disintegration time were seen. Repeated compaction and precompression reduced the tensile strength and the increased disintegration time of the DCP tablets, but improved the strength and friability of Starch 1500 tablets. Based on the data reported, routine laboratory measurement of tablet work of compaction may have potential as a critical quality attribute of a powder blend for compression. The instrumented press was suitable for student use with minimal supervisor input.

Evaluation of a setting reaction pathway in the novel composite TiHA-CSD bone cement by FT-Raman and FT-IR spectroscopy

NASA Astrophysics Data System (ADS)

Paluszkiewicz, Czesława; Czechowska, Joanna; Ślósarczyk, Anna; Paszkiewicz, Zofia

2013-02-01

The aim of this study was to determine a setting reaction pathway in a novel, surgically handy implant material, based on calcium sulfate hemihydrate (CSH) and titanium doped hydroxyapatite (TiHA). The previous studies confirmed superior biological properties of TiHA in comparison to the undoped hydroxyapatite (HA) what makes it highly attractive for future medical applications. In this study the three types of titanium modified HA powders: untreated, calcined at 800 °C, sintered at 1250 °C and CSH were used to produce bone cements. The Fourier Transform-InfraRed (FT-IR) spectroscopy and Raman spectroscopy were applied to evaluate processes taking place during the setting of the studied materials. Our results undoubtedly confirmed that the reaction pathways and the phase compositions differed significantly for set cements and were dependent on the initial heat treatment of TiHA powder. Final materials were multiphase composites consisting of calcium sulfate dihydrate, bassanite, tricalcium phosphate, hydroxyapatite and calcium titanate (perovskite). The FT-IR and Scanning Electron Microscopy (SEM) measurements performed after the incubation of the cement samples in the simulated body fluid (SBF), indicate on high bioactive potential of the obtained bone cements.

A novel extremophile strategy studied by Raman spectroscopy

NASA Astrophysics Data System (ADS)

Edwards, Howell G. M.

2007-12-01

A case is made for the classification of the colonisation by Dirina massiliensis forma sorediata of pigments on ancient wall-paintings as extremophilic behaviour. The lichen encrustations studied using FT-Raman spectroscopy have yielded important molecular information which has assisted in the identification of the survival strategy of the organism in the presence of significant levels of heavy metal toxins. The production of a carotenoid, probably astaxanthin, at the surface of the lichen thalli is identified from its characteristic biomolecular signatures in the Raman spectrum, whereas the presence of calcium oxalate dihydrate (weddellite) has been identified at both the upper and lower surfaces of the thalli and in core samples taken from depths of up to 10 mm through the encrustation into the rock substrate. The latter observation explains the significant disintegrative biodeteriorative effect of the colonisation upon the integrity of the wall-paintings and can be used to direct conservatorial and preservation efforts of the art work. A surprising result proved to be the absence of Raman spectroscopic evidence for the complexation of the metal pigments by the oxalic acid produced by the metabolic action of the organisms, unlike several cases that have been reported in the literature.

Spectroscopic studies of model polar stratospheric cloud films

NASA Technical Reports Server (NTRS)

Tolbert, Margaret A.; Koehler, Birgit G.; Middlebrook, Ann M.

1993-01-01

Fourier transform infrared (FTIR) spectroscopy has been used to study nitric-acid/ice films representative of type I polar stratospheric clouds (PSCs). These studies reveal that in addition to amorphous nitric acid/ice mixtures, there are three stable stoichiometric hydrates of nitric acid: nitric-acid monohydrate (NAM), dihydrate (NAD), and trihydrate (NAT). We also observe two distinct crystalline forms of the trihydrate, which we denote alpha- and beta-NAT. These two forms appear to differ in their concentration of crystalline defects, but not in their chemical composition. In addition to probing the composition of type I PSCs, we have also used FTIR spectroscopy to study the interaction of HCl with model PSC films. In this work we find that for HCl pressures in the range 10 exp -5 to 10 exp -7 Torr, HCl is taken up by ice at 155 K to form a thin layer of HCl.6H2O. At 193 K, the uptake of HCl by ice was consistent with less than or equal to monolayer coverage. Uptake of HCl by alpha and beta-NAT at 175 K was also consistent with less than or equal to monolayer coverage.

Enhanced photocatalytic activity of nanocellulose supported zinc oxide composite for RhB dye as well as ciprofloxacin drug under sunlight/visible light

NASA Astrophysics Data System (ADS)

Tavker, Neha; Sharma, Manu

2018-05-01

Zinc oxide nanoparticles were synthesised from zinc acetate di-hydrate via co-precipitation method. Nanocellulose was isolated from agrowaste using chemo-mechanical treatments and characterized. Nanocellulose supported zinc oxide composites were prepared through in-situ method by adding different amounts of nanocellulose. The photocatalytic efficiency of pure Zno and nanocellulose supported ZnO was calculated using RhB dye under visible light and sun light. The composites which had nanocellulose in greater ratio showed higher degradation efficiency in sunlight rather than visible light for both; dye and drug. All the composites showed high rate of photodegradation compared to bare ZnO and bare nanocellulose. The enhancement in photocatalytic activity was observed maximum where the amount of cellulose was maximum. The maximum observed rate was 0.025 min-1 using Ciprofloxacin drug due to the increase in lifetime of Z4 sample delaying the electron and hole pair recombination. The degrading efficiency of nanocellulose supported zinc oxide (NC/ZnO) composite for RhB was found to be 35% in visible, 76% in sunlight and 75% for ciprofloxacin under sunlight.

Electroless Cu Plating on Anodized Al Substrate for High Power LED.

PubMed

Rha, Sa-Kyun; Lee, Youn-Seoung

2015-03-01

Area-selective copper deposition on screen printed Ag pattern/anodized Al/Al substrate was attempted using a neutral electroless plating processes for printed circuit boards (PCBs), according to a range of variation of pH 6.5-pH 8 at 70 °C. The utilized basic electroless solution consisted of copper(II) sulfate pentahydrate, sodium phosphinate monohydrate, sodium citrate tribasic dihydrate, ammonium chloride, and nickel(II) sulfate hexahydrate. The pH of the copper plating solutions was adjusted from pH 6.5 to pH 8 using NH4OH. Using electroless plating in pH 6.5 and pH 7 baths, surface damage to the anodized Al layer hardly occurred; the structure of the plated Cu-rich films was a typical fcc-Cu, but a small Ni component was co-deposited. In electroless plating at pH 8, the surface of the anodized Al layer was damaged and the Cu film was composed of a lot of Ni and P which were co-deposited with Cu. Finally, in a pH 7 bath, we can make a selectively electroless plated Cu film on a PCB without any lithography and without surface damage to the anodized Al layer.

Facile Synthesis of Ultralong and Thin Copper Nanowires and Its Application to High-Performance Flexible Transparent Conductive Electrodes

NASA Astrophysics Data System (ADS)

Wang, Yaxiong; Liu, Ping; Zeng, Baoqing; Liu, Liming; Yang, Jianjun

2018-03-01

A hydrothermal method for synthesizing ultralong and thin copper nanowires (CuNWs) with average diameter of 35 nm and average length of 100 μm is demonstrated in this paper. The concerning raw materials include copric (II) chloride dihydrate (CuCl2·2H2O), octadecylamine (ODA), and ascorbic acid, which are all very cheap and nontoxic. The effect of different reaction time and different molar ratios to the reaction products were researched. The CuNWs prepared by the hydrothermal method were applied to fabricate CuNW transparent conductive electrode (TCE), which exhibited excellent conductivity-transmittance performance with low sheet resistance of 26.23 Ω /\\square and high transparency at 550 nm of 89.06% (excluding Polyethylene terephthalate (PET) substrate). The electrode fabrication process was carried out at room temperature, and there was no need for post-treatment. In order to decrease roughness and protect CuNW TCEs against being oxidized, we fabricated CuNW/poly(methyl methacrylate) (PMMA) hybrid TCEs (HTCEs) using PMMA solution. The CuNW/PMMA HTCEs exhibited low surface roughness and chemical stability as compared with CuNW TCEs.

Photocatalytic degradation of sunscreen active ingredients mediated by nanostructured materials

NASA Astrophysics Data System (ADS)

Soto-Vazquez, Loraine

Water scarcity and pollution are environmental issues with terrible consequences. In recent years several pharmaceutical and personal care products, such as sunscreen active ingredients, have been detected in different water matrices. Its recalcitrant behavior in the environment has caused controversies and generated countless questions about its safety. During this research, we employed an advanced oxidation process (photocatalysis) to degrade sunscreen active ingredients. For this study, we used a 3x3 system, evaluating three photocatalysts and three different contaminants. From the three catalysts employed, two of them were synthesized. ZnO nanoparticles were obtained using zinc acetate dihydrated as the precursor, and TiO2 nanowires were synthesized from titanium tetrachloride precursor. The third catalyst employed (namely, P25) was obtained commercially. The synthesized photocatalysts were characterized in terms of the morphology, elemental composition, crystalline structure, elemental oxidation states, vibrational modes and surface area, using SEM-EDS, XRD, XPS, Raman spectroscopy and BET measurements, respectively. The photocatalysts were employed during the study of the degradation of p-aminobenzoic acid, phenylbenzimidazole sulfonic acid, and benzophenone-4. In all the cases, at least 50% degradation was achieved. P25 showed degradation efficiencies above 90%, and from the nine systems, 7 of them degraded at least 86%.

Phosphorus forms and extractability in dairy manure: a case study for Wisconsin on-farm anaerobic digesters.

PubMed

Güngör, Kerem; Karthikeyan, K G

2008-01-01

The effect of anaerobic digestion on phosphorus (P) forms and water P extractability was investigated using dairy manure samples from six full-scale on-farm anaerobic digesters in Wisconsin, USA. On an average, total dissolved P (TDP) constituted 12 +/- 4% of total P (TP) in the influent to the anaerobic digesters. Only 7 +/- 2% of the effluent was in a dissolved form. Dissolved unreactive P (DUP), comprising polyphosphates and organic P, dominated the dissolved P component in both the influent and effluent. In most cases, it appeared that the fraction of DUP mineralized during anaerobic digestion became subsequently associated with particulate-bound solids. Geochemical equilibrium modeling with Mineql+ indicated that dicalcium phosphate dihydrate, dicalcium phosphate anhydrous, octacalcium phosphate, newberyite, and struvite were the probable solid phases in both the digester influent and effluent samples. The water-extractable P (WEP) fraction in undigested manure ranged from 45% to 70% of TP, which reduced substantially after anaerobic digestion to 25% to 45% of TP. Anaerobic digestion of dairy manure appears capable of reducing the fraction of P that is immediately available by increasing the stability of the solid phases controlling P solubility.

Physicochemical and mechanical properties of carbamazepine cocrystals with saccharin.

PubMed

Rahman, Ziyaur; Samy, Raghu; Sayeed, Vilayat A; Khan, Mansoor A

2012-01-01

The aim of present research was to investigate the physicochemical, mechanical properties, and stability characteristics of cocrystal of carbamazepine (CBZ) using saccharin (SAC) as a coformer. The cocrystals were prepared by solubility method and characterized by pH-solubility profile, intrinsic dissolution by static disk method, and surface morphology by scanning electron microscopy (SEM), crystallinity by differential scanning calorimetry (DSC) and powder X-ray diffraction (PXRD), and mechanical properties by Heckel analysis. Stability of the cocrystals were assessed by storing them at 60 (°)C for two weeks, 25 (°)C/60%RH, 40 (°)C/75%RH and 40 (°)C/94%RH for one month and compared with the stability of CBZ. The solubility profile of cocrystal was similar to CBZ. The cocrystal and CBZ have shown the same stability profile at all the conditions of studies except at 40 (°)C/94%RH. Unlike the CBZ, cocrystal was stable against dihydrate transformation. The compacts of cocrystal have a greater tensile strength and more compressibility. The Heckel analysis suggested that plastic deformation started at low compression pressure in the cocrystal than CBZ. In summary, the cocrystal form of carbamazepine provides another avenue for product development which is more stable than the parent drug.

Effects of heating and calcium and phosphate mineral supplementation on the physical properties of rennet-induced coagulation of camel and cow milk gels.

PubMed

Kamal, Mohammad; Foukani, Mohammed; Karoui, Romdhane

2017-05-01

The physical properties of rennet-induced coagulation of preheated camel and cow milk gels (50 and 70 °C for 10 min) enriched with calcium chloride (CaCl2) and hydrogen phosphate dihydrate (Na2HPO42H2O) were evaluated using the dynamic low amplitude oscillatory shear analysis. The storage modulus (G') and loss modulus (G") of camel milk gels showed significant (P < 0·05) lower values than those of cow milk gels. The preheating of camel milk at 50 °C affected negatively the gelation properties, while the preheating at 70 °C prevented the formation of rennet-induced milk gels. No effect was observed on the gelation properties of cow milk gels. The CaCl2 added at 10 and 20 mM to preheated camel and cow milk reduced significantly (P < 0·05) the gelation time and increased the gel firmness. In contrast, Na2HPO42H2O added at 10 and 20 mM induced the formation of weak gels for preheated camel and cow milk at 50 °C, and even no gelation for preheated camel milk at 70 °C.

Extraction of pectin from passion fruit rind (Passiflora edulis var. flavicarpa Degener) for edible coating

NASA Astrophysics Data System (ADS)

Inayati, Puspita, Rifka Intan; Fajrin, Vika Latifiana

2018-02-01

One of fruit preservation method is by applying the edible coating. Rind of passion fruit (Passiflora edulis var. flavicarpa Degener), which is kind of waste, can be utilized as edible coating through pectin extraction process. The purposes of this work were to determine the suitable solvent for the pectin extraction and techniques for applying the produced edible coating on strawberry, to produce edible coating from the pectin, and the test the performance of the edible coating which was applied to strawberries. Pectin from passion fruit rind was collected through conventional extraction method using two types of solvent, i.e. acetic acid solution and hydrochloric acid solution with concentration of 0.01 N, 0.015 N, 0.02 N, 0.025 N, and 0.03 N. The results showed that chloric acid solution was more suitable for the pectin extraction from passion fruit. Maximum yield of 30.78% was obtained at hydrochloric acid concentration of 0.02 N. Obtained pectin from the extraction was then processed into the edible coating by adding plasticizers and calcium chloride dihydrate. Storability of the coated strawberry was observed to measure the performance of the edible coating

Isolation of site-specific anharmonicities of individual water molecules in the I-·(H2O)2 complex using tag-free, isotopomer selective IR-IR double resonance

NASA Astrophysics Data System (ADS)

Yang, Nan; Duong, Chinh H.; Kelleher, Patrick J.; Johnson, Mark A.; McCoy, Anne B.

2017-12-01

We reveal the microscopic mechanics of iodide ion microhydration by recording the isotopomer-selective vibrational spectra of the I-·(H2O)·(D2O), I-·(HOD)·(D2O), and I-·(DOH)·(H2O) isotopologues using a new class of ion spectrometer that is optimized to carry out two-color, IR-IR photodissociation in a variety of pump-probe schemes. Using one of these, we record the linear absorption spectrum of a cryogenically cooled cluster without the use of a messenger ;tag;. In another protocol, we reveal the spectra of individual H2O and D2O molecules embedded in each of the two possible binding sites in the iodide dihydrate, as well as the bands due to individual OH and OD groups in each of the four local binding environments. Finally, we demonstrate how temperature dependent isotopic scrambling among the spectral features can be used to monitor the onset of large amplitude motion, heretofore inferred from changes in the envelope of the OH stretching vibrational manifold.

Simulations of Polar Stratospheric Clouds and Denitrification Using Laboratory Freezing Rates

NASA Technical Reports Server (NTRS)

Drdla, Katja; Tabazadeh, Azadeh; Gore, Warren J. (Technical Monitor)

2001-01-01

During the 1999-2000 Arctic winter, the SAGE (Stratospheric Aerosol and Gas Experiment) III Ozone Loss and Validation Experiment (SOLVE) provided evidence of widespread solid-phase polar stratospheric clouds (PSCs) accompanied by severe nitrification. Previous simulations have shown that a freezing process occurring at temperatures above the ice frost point is necessary to explain these observations. In this work, the nitric acid freezing rates measured by Salcedo et al. and discussed by Tabazadeh et al. have been examined. These freezing rates have been tested in winter-long microphysical simulations of the 1999-2000 Arctic vortex evolution in order to determine whether they can explain the observations. A range of cases have been explored, including whether the PSC particles are composed of nitric acid dihydrate or trihydrate, whether the freezing process is a bulk process or occurs only on the particle surfaces, and uncertainties in the derived freezing rates. Finally, the possibility that meteoritic debris enhances the freezing rate has also been examined. The results of these simulations have been compared with key PSC and denitrification measurements made by the SOLVE campaign. The cases that best reproduce the measurements will he highlighted, with a discussion of the implications for our understanding of PSCs.

Laboratory studies of the low-temperature deliquescence of calcium chloride salts: Relevance to aqueous solutions on Mars and in the Antarctic Dry Valleys

NASA Astrophysics Data System (ADS)

Gough, R. V.; Chevrier, V.; Tolbert, M. A.

2013-12-01

There is significant interest in the possible existence of liquid water on current Mars. This water would likely exist as a brine in order to be stable on Mars today. It has been proposed that soil salts could form aqueous solutions through either the melting of ice by low-eutectic salts, or by the deliquescence of hygroscopic salts present in the Martian soil. The focus thus far has largely been on perchlorate species, which can melt ice at temperatures as low as 206 K and can deliquesce at relative humidity values as low as 38% RH. A Mars-relevant salt that has been neglected thus far is calcium chloride (CaCl2). Calcium has been reported to be an abundant cation at the Phoenix landing site and Mars Science Laboratory instruments have recently identified calcium as well. Simulations suggest subsurface CaCl2 is an ideal candidate to produce brines with seasonality consistent with observed recurring slope lineae (RSL) (Chevrier et al., 2012). Finally, the only terrestrial site where RSL-like features have been observed (near Don Juan Pond in the Antarctic Dry Valleys) contains abundant CaCl2. These seasonal slope streaks are thought to form when CaCl2 in the soil deliquesces due to contact with atmospheric water vapor (Dickson et al., 2013). It is important to understand how this CaCl2 interacts with water vapor at low temperatures relevant to Mars and the Martian analog sites. Here we use a Raman microscope and environmental cell to monitor the low-temperature (223 - 273 K) deliquescence (solid to aqueous phase transition) and efflorescence (aqueous to solid phase transition) of three hydration states of CaCl2 (dihydrate, tetrahydrate, hexahydrate). We have found that the deliquescence relative humidity (DRH) increases with increasing hydration state, which is an expected result. Average DRH values over the temperature range studied are 20.0 × 2.6% RH for the dihydrate, 31.8 × 6.3% RH for the tetrahydrate and 60.7 × 1.6% RH for the hexahydrate. Once the aqueous solution has formed, efflorescence (recrystallization) of the salt is kinetically hindered and supersaturated solutions can exist at humidities far below the DRH. Regardless of temperature or initial hydration state of the solid salt, we do not observe efflorescence of the aqueous solutions to occur until single digit RH values are reached. We show here that calcium chloride is at least as deliquescent as many perchlorate salts, and that solutions of calcium chloride are even more difficult to recrystallize once a brine solution has formed. These experimental results will assist with interpretation of observations of deliquescence in the Antarctic Dry Valleys and will help us understand potential liquid water formation on Mars. In addition to formation of brines through melting, deliquescence of salts such as CaCl2 is a reasonable mechanism for formation of aqueous solutions on current Mars.

Anti-solvent crystallization of L-threonine in Taylor crystallizers and MSMPR crystallizer: Effect of fluid dynamic motions on crystal size, shape, and recovery

NASA Astrophysics Data System (ADS)

Lee, Sooyun; Lee, Choul-Ho; Kim, Woo-Sik

2017-07-01

The influence of the fluid dynamic motions of a periodic Taylor vortex and random turbulent eddy on the anti-solvent crystallization of L-threonine was investigated. The Taylor vortex flow and random turbulent eddy flow were generated by the inner cylinder rotation in a Couette-Taylor (CT) crystallizer and the impeller agitation in a mixed-suspension mixed product removal (MSMPR) crystallizer, respectively. Furthermore, the circumferentially sinusoidal fluctuation of a Taylor vortex was induced in an elliptical Couette-Taylor (ECT) crystallizer . The periodic Taylor vortex flows in the CT and ECT crystallizers resulted in a smaller crystal size and higher crystal recovery ratio of L-threonine than the random turbulent flow in the MSMPR crystallizer due to induction of a higher supersaturation, resulting in a higher nucleation in the CT and ECT crystallizers than in the MSMPR crystallizer. Thus, the crystal size was reduced and the crystal recovery ratio enhanced when increasing the rotation/agitation speed and feed flow rate in the CT, ECT, and MSMPR crystallizers. When increasing the temperature, the crystal size and crystal recovery ratio were both increased due an enhanced mass transfer for crystal growth. The crystal morphology changes according to the fluid dynamic motion with various crystallization conditions were well correlated in terms of the supersaturation.

The Biological Macromolecule Crystallization Database and NASA Protein Crystal Growth Archive

PubMed Central

Gilliland, Gary L.; Tung, Michael; Ladner, Jane

1996-01-01

The NIST/NASA/CARB Biological Macromolecule Crystallization Database (BMCD), NIST Standard Reference Database 21, contains crystal data and crystallization conditions for biological macromolecules. The database entries include data abstracted from published crystallographic reports. Each entry consists of information describing the biological macromolecule crystallized and crystal data and the crystallization conditions for each crystal form. The BMCD serves as the NASA Protein Crystal Growth Archive in that it contains protocols and results of crystallization experiments undertaken in microgravity (space). These database entries report the results, whether successful or not, from NASA-sponsored protein crystal growth experiments in microgravity and from microgravity crystallization studies sponsored by other international organizations. The BMCD was designed as a tool to assist x-ray crystallographers in the development of protocols to crystallize biological macromolecules, those that have previously been crystallized, and those that have not been crystallized. PMID:11542472

Fast surface crystallization of amorphous griseofulvin below T g.

PubMed

Zhu, Lei; Jona, Janan; Nagapudi, Karthik; Wu, Tian

2010-08-01

To study crystal growth rates of amorphous griseofulvin (GSF) below its glass transition temperature (T (g)) and the effect of surface crystallization on the overall crystallization kinetics of amorphous GSF. Amorphous GSF was generated by melt quenching. Surface and bulk crystal growth rates were determined using polarized light microscope. X-ray powder diffraction (XRPD) and Raman microscopy were used to identify the polymorph of the crystals. Crystallization kinetics of amorphous GSF powder stored at 40 degrees C (T (g)-48 degrees C) and room temperature (T (g)-66 degrees C) was monitored using XRPD. Crystal growth at the surface of amorphous GSF is 10- to 100-fold faster than that in the bulk. The surface crystal growth can be suppressed by an ultrathin gold coating. Below T (g), the crystallization of amorphous GSF powder was biphasic with a rapid initial crystallization stage dominated by the surface crystallization and a slow or suspended late stage controlled by the bulk crystallization. GSF exhibits the fastest surface crystallization kinetics among the known amorphous pharmaceutical solids. Well below T (g), surface crystallization dominated the overall crystallization kinetics of amorphous GSF powder. Thus, surface crystallization should be distinguished from bulk crystallization in studying, modeling and controlling the crystallization of amorphous solids.

Photonic time crystals.

PubMed

Zeng, Lunwu; Xu, Jin; Wang, Chengen; Zhang, Jianhua; Zhao, Yuting; Zeng, Jing; Song, Runxia

2017-12-07

When space (time) translation symmetry is spontaneously broken, the space crystal (time crystal) forms; when permittivity and permeability periodically vary with space (time), the photonic crystal (photonic time crystal) forms. We proposed the concept of photonic time crystal and rewritten the Maxwell's equations. Utilizing Finite Difference Time Domain (FDTD) method, we simulated electromagnetic wave propagation in photonic time crystal and photonic space-time crystal, the simulation results show that more intensive scatter fields can obtained in photonic time crystal and photonic space-time crystal.

Advanced Protein Crystallization Facility (APCF)

NASA Technical Reports Server (NTRS)

1998-01-01

This section of the Life and Microgravity Spacelab (LMS) publication contains articles entitled: (1) Crystallization of EGFR-EGF; (2) Crystallization of Apocrustacyanin C1; (3) Crystallization and X-ray Analysis of 5S rRNA and the 5S rRNA Domain A; (4) Growth of Lysozyme Crystals at Low Nucleation Density; (5) Comparative Analysis of Aspartyl tRNA-synthetase and Thaumatin Crystals Grown on Earth and In Microgravity; (6) Lysosome Crystal Growth in the Advanced Protein Crystallization Facility Monitored via Mach-Zehnder Interferometry and CCD Video; (7) Analysis of Thaumatin Crystals Grown on Earth and in Microgravity; (8) Crystallization of the Nucleosome Core Particle; (9) Crystallization of Photosystem I; (10) Mechanism of Membrane Protein Crystal Growth: Bacteriorhodopsin-mixed Micelle Packing at the Consolution Boundary, Stabilized in Microgravity; (11) Crystallization in a Microgravity Environment of CcdB, a Protein Involved in the Control of Cell Death; and (12) Crystallization of Sulfolobus Solfataricus

Causes of fragmented crystals in ignimbrites: a case study of the Cardones ignimbrite, Northern Chile

NASA Astrophysics Data System (ADS)

van Zalinge, M. E.; Cashman, K. V.; Sparks, R. S. J.

2018-03-01

Broken crystals have been documented in many large-volume caldera-forming ignimbrites and can help to understand the role of crystal fragmentation in both eruption and compaction processes, the latter generally overlooked in the literature. This study investigates the origin of fragmented crystals in the > 1260 km3, crystal-rich Cardones ignimbrites located in the Central Andes. Observations of fragmented crystals in non-welded pumice clasts indicate that primary fragmentation includes extensive crystal breakage and an associated ca. 5 vol% expansion of individual crystals while preserving their original shapes. These observations are consistent with the hypothesis that crystals fragment in a brittle response to rapid decompression associated with the eruption. Additionally, we observe that the extent of crystal fragmentation increases with increasing stratigraphic depth in the ignimbrite, recording secondary crystal fragmentation during welding and compaction. Secondary crystal fragmentation aids welding and compaction in two ways. First, enhanced crystal fragmentation at crystal-crystal contacts accommodates compaction along the principal axis of stress. Second, rotation and displacement of individual crystal fragments enhances lateral flow in the direction(s) of least principal stress. This process increases crystal aspect ratios and forms textures that resemble mantled porphyroclasts in shear zones, indicating lateral flow adds to processes of compaction and welding alongside bubble collapse. In the Cardones ignimbrite, secondary fragmentation commences at depths of 175-250 m (lithostatic pressures 4-6 MPa), and is modulated by both the overlying crystal load and the time spent above the glass transition temperature. Under these conditions, the existence of force-chains can produce stresses at crystal-crystal contacts of a few times the lithostatic pressure. We suggest that documenting crystal textures, in addition to conventional welding parameters, can provide useful information about welding processes in thick crystal-rich ignimbrites.

Improvement of crystal identification performance for a four-layer DOI detector composed of crystals segmented by laser processing

NASA Astrophysics Data System (ADS)

Mohammadi, Akram; Inadama, Naoko; Yoshida, Eiji; Nishikido, Fumihiko; Shimizu, Keiji; Yamaya, Taiga

2017-09-01

We have developed a four-layer depth of interaction (DOI) detector with single-side photon readout, in which segmented crystals with the patterned reflector insertion are separately identified by the Anger-type calculation. Optical conditions between segmented crystals, where there is no reflector, affect crystal identification ability. Our objective of this work was to improve crystal identification performance of the four-layer DOI detector that uses crystals segmented with a recently developed laser processing technique to include laser processed boundaries (LPBs). The detector consisted of 2 × 2 × 4mm3 LYSO crystals and a 4 × 4 array multianode photomultiplier tube (PMT) with 4.5 mm anode pitch. The 2D position map of the detector was calculated by the Anger calculation method. At first, influence of optical condition on crystal identification was evaluated for a one-layer detector consisting of a 2 × 2 crystal array with three different optical conditions between the crystals: crystals stuck together using room temperature vulcanized (RTV) rubber, crystals with air coupling and segmented crystals with LPBs. The crystal array with LPBs gave the shortest distance between crystal responses in the 2D position map compared with the crystal array coupled with RTV rubber or air due to the great amount of cross-talk between segmented crystals with LPBs. These results were used to find optical conditions offering the optimum distance between crystal responses in the 2D position map for the four-layer DOI detector. Crystal identification performance for the four-layer DOI detector consisting of an 8 × 8 array of crystals segmented with LPBs was examined and it was not acceptable for the crystals in the first layer. The crystal identification was improved for the first layer by changing the optical conditions between all 2 × 2 crystal arrays of the first layer to RTV coupling. More improvement was observed by combining different optical conditions between all crystals of the first layer and some crystals of the second and the third layers of the segmented array.

Crystal growth and annealing for minimized residual stress

DOEpatents

Gianoulakis, Steven E.

2002-01-01

A method and apparatus for producing crystals that minimizes birefringence even at large crystal sizes, and is suitable for production of CaF.sub.2 crystals. The method of the present invention comprises annealing a crystal by maintaining a minimal temperature gradient in the crystal while slowly reducing the bulk temperature of the crystal. An apparatus according to the present invention includes a thermal control system added to a crystal growth and annealing apparatus, wherein the thermal control system allows a temperature gradient during crystal growth but minimizes the temperature gradient during crystal annealing.

Protein crystal growth; Proceedings of the First International Conference, Stanford University, CA, August 14-16, 1985

NASA Technical Reports Server (NTRS)

Feigelson, R. S. (Editor)

1986-01-01

Papers are presented on mechanisms of nucleation and growth of protein crystals, the role of purification in the crystallization of proteins and nucleic acids, and the effect of chemical impurities in polyethylene glycol on macromolecular crystallization. Also considered are growth kinetics of tetragonal lysozyme crystals, thermodynamic and kinetic considerations for crystal growth of complex molecules from solution, protein single-crystal growth under microgravity, and growth of organic crystals in a microgravity environment. Papers are also presented on preliminary investigations of protein crystal growth using the Space Shuttle, convective diffusion in protein crystal growth, and the growth and characterization of membrane protein crystals.

Crystallization and X-ray diffraction of crystals formed in water-plasticized amorphous lactose.

PubMed

Jouppila, K; Kansikas, J; Roos, Y H

1998-01-01

Effects of storage time and relative humidity on crystallization and crystal forms produced from amorphous lactose were investigated. Crystallization was observed from time-dependent loss of sorbed water and increasing intensities of peaks in X-ray diffraction patterns. The rate of crystallization increased with increasing storage relative humidity. Lactose crystallized mainly as alpha-lactose monohydrate and anhydrous crystals with alpha- and beta-lactose in a molar ratio of 5:3. The results suggested that the crystal form was defined by the early nucleation process. The crystallization data are important in modeling of crystallization phenomena and prediction of stability of lactose-containing food and pharmaceutical materials.

Liquid Crystals in Chromatography

NASA Astrophysics Data System (ADS)

Witkiewicz, Zygfryd

The following sections are included: * INTRODUCTION * LIQUID CRYSTALS SUITABLE FOR GAS CHROMATOGRAPHY * Monomeric Liquid Crystal Stationary Phases * Polymeric Liquid Crystal Stationary Phases * Polymeric Liquid Crystal Stationary Phases * Conventional Analytical Columns * Capillary Columns * FACTORS AFFECTING THE CHROMATOGRAPHIC SEPARATIONS ON LIQUID CRYSTAL STATIONARY PHASES * Kind of Mesophase of the Liquid Crystal * Molecular Structure of the Liquid Crystals and of the Chromatographed Substances * Substrate on which the Liquid Crystal is Deposited * ANALYTICAL APPLICATIONS OF LIQUID CRYSTAL STATIONARY PHASES IN GAS CHROMATOGRAPHY * Separation of Isomers of Benzene and Naphthalene Derivatives * Separation of Alkane and Alkene Isomers * Separation of Mixtures of Benzene and Aliphatic Hydrocarbon Derivatives Containing Heteroatoms * Separation of Polynuclear Hydrocarbons * INVESTIGATION OF THE PROPERTIES OF LIQUID CRYSTALS BY GAS CHROMATOGRAPHY * APPLICATION OF LIQUID CRYSTALS IN LIQUID CHROMATOGRAPHY * Column Chromatography * Thin-Layer Chromatography * APPLICATION OF LIQUID CRYSTAL STATIONARY PHASES IN SUPERCRITICAL FLUID CHROMATOGRAPHY * FINAL REMARKS * References

The application of crystal soaking technique to study the effect of zinc and cresol on insulinotropin crystals grown from a saline solution.

PubMed

Kim, Y; Haren, A M

1995-11-01

The purpose of this study is to investigate the effect of zinc and cresol on the structure of insulinotropin crystals. Insulinotropin crystals grown from a saline solution were treated with zinc and/or m-cresol using a crystal soaking technique. The effects of these additives on the crystal structure were investigated with powder X-ray diffraction, photomicrography, and differential scanning calorimetry. The molecular interaction between insulinotropin and m-trifluorocresol in solution was also studied by 19F NMR: The data suggest that the original crystals grown from a saline solution have relatively weak lattice forces. After the addition of m-cresol to the suspension of the insulinotropin crystals, the crystals were immediately rendered amorphous. The m-cresol molecules which diffused into the crystals through solvent channels may have disturbed the lattice interactions that maintain the integrity of the crystal. In contrast, the zinc added to the suspension stabilized the crystal lattice so that the subsequent addition of m-cresol did not alter the integrity of the crystals. A marked increase in melting point (206 degrees versus 184 degrees) and heat of fusion (24.6 J/g versus 1.4 J/g) of the crystals was observed after the treatment with zinc. The solubility of the zinc treated crystals in a pH 7.1 phosphate buffered saline was 1/20 of that of the original crystals. When the insulinotropin crystals were treated with the additives using a crystal soaking method, the crystals underwent structural changes. Zinc stabilized the crystal lattice, and reduced the solubility of the peptide.

Acoustic Methods to Monitor Protein Crystallization and to Detect Protein Crystals in Suspensions of Agarose and Lipidic Cubic Phase.

PubMed

Ericson, Daniel L; Yin, Xingyu; Scalia, Alexander; Samara, Yasmin N; Stearns, Richard; Vlahos, Harry; Ellson, Richard; Sweet, Robert M; Soares, Alexei S

2016-02-01

Improvements needed for automated crystallography include crystal detection and crystal harvesting. A technique that uses acoustic droplet ejection to harvest crystals was previously reported. Here a method is described for using the same acoustic instrument to detect protein crystals and to monitor crystal growth. Acoustic pulses were used to monitor the progress of crystallization trials and to detect the presence and location of protein crystals. Crystals were detected, and crystallization was monitored in aqueous solutions and in lipidic cubic phase. Using a commercially available acoustic instrument, crystals measuring ~150 µm or larger were readily detected. Simple laboratory techniques were used to increase the sensitivity to 50 µm by suspending the crystals away from the plastic surface of the crystallization plate. This increased the sensitivity by separating the strong signal generated by the plate bottom that can mask the signal from small protein crystals. It is possible to further boost the acoustic reflection from small crystals by reducing the wavelength of the incident sound pulse, but our current instrumentation does not allow this option. In the future, commercially available sound-emitting transducers with a characteristic frequency near 300 MHz should detect and monitor the growth of individual 3 µm crystals. © 2015 Society for Laboratory Automation and Screening.

Acoustic Methods to Monitor Protein Crystallization and to Detect Protein Crystals in Suspensions of Agarose and Lipidic Cubic Phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ericson, Daniel L.; Yin, Xingyu; Scalia, Alexander

2016-02-01

Improvements needed for automated crystallography include crystal detection and crystal harvesting. A technique that uses acoustic droplet ejection to harvest crystals was previously reported. Here a method is described for using the same acoustic instrument to detect protein crystals and to monitor crystal growth. Acoustic pulses were used to monitor the progress of crystallization trials and to detect the presence and location of protein crystals. Crystals were detected, and crystallization was monitored in aqueous solutions and in lipidic cubic phase. Using a commercially available acoustic instrument, crystals measuring ~150 µm or larger were readily detected. Simple laboratory techniques were usedmore » to increase the sensitivity to 50 µm by suspending the crystals away from the plastic surface of the crystallization plate. This increased the sensitivity by separating the strong signal generated by the plate bottom that can mask the signal from small protein crystals. It is possible to further boost the acoustic reflection from small crystals by reducing the wavelength of the incident sound pulse, but our current instrumentation does not allow this option. In the future, commercially available sound-emitting transducers with a characteristic frequency near 300 MHz should detect and monitor the growth of individual 3 µm crystals.« less

High-throughput crystallization screening.

PubMed

Skarina, Tatiana; Xu, Xiaohui; Evdokimova, Elena; Savchenko, Alexei

2014-01-01

Protein structure determination by X-ray crystallography is dependent on obtaining a single protein crystal suitable for diffraction data collection. Due to this requirement, protein crystallization represents a key step in protein structure determination. The conditions for protein crystallization have to be determined empirically for each protein, making this step also a bottleneck in the structure determination process. Typical protein crystallization practice involves parallel setup and monitoring of a considerable number of individual protein crystallization experiments (also called crystallization trials). In these trials the aliquots of purified protein are mixed with a range of solutions composed of a precipitating agent, buffer, and sometimes an additive that have been previously successful in prompting protein crystallization. The individual chemical conditions in which a particular protein shows signs of crystallization are used as a starting point for further crystallization experiments. The goal is optimizing the formation of individual protein crystals of sufficient size and quality to make them suitable for diffraction data collection. Thus the composition of the primary crystallization screen is critical for successful crystallization.Systematic analysis of crystallization experiments carried out on several hundred proteins as part of large-scale structural genomics efforts allowed the optimization of the protein crystallization protocol and identification of a minimal set of 96 crystallization solutions (the "TRAP" screen) that, in our experience, led to crystallization of the maximum number of proteins.

Role of Solvents in Improvement of Dissolution Rate of Drugs: Crystal Habit and Crystal Agglomeration

PubMed Central

Maghsoodi, Maryam

2015-01-01

Crystallization is often used for manufacturing drug substances. Advances of crystallization have achieved control over drug identity and purity, but control over the physical form remains poor. This review discusses the influence of solvents used in crystallization process on crystal habit and agglomeration of crystals with potential implication for dissolution. According to literature it has been known that habit modification of crystals by use of proper solvents may enhance the dissolution properties by changing the size, number and the nature of crystal faces exposed to the dissolution medium. Also, the faster dissolution rate of drug from the agglomerates of crystals compared with the single crystals may be related to porous structure of the agglomerates and consequently their better wettability. It is concluded from this review that in-depth understanding of role of the solvents in crystallization process can be applied to engineering of crystal habit or crystal agglomeration, and predictably dissolution improvement in poorly soluble drugs. PMID:25789214

GROWTH AND CHARACTERIZATION OF SINGLE CRYSTALS OF RARE EARTH COMPOUNDS.

DTIC Science & Technology

SINGLE CRYSTALS, CRYSTAL GROWTH), (*CRYSTAL GROWTH, SINGLE CRYSTALS), (*RARE EARTH COMPOUNDS, SINGLE CRYSTALS), EPITAXIAL GROWTH, SODIUM COMPOUNDS, CHLORIDES, VAPOR PLATING, ELECTROSTATIC FIELDS, ENERGY, ATOMIC PROPERTIES , BONDING

Use of dye to distinguish salt and protein crystals under microcrystallization conditions

NASA Technical Reports Server (NTRS)

Cosenza, Larry (Inventor); Gester, Thomas E. (Inventor); Bray, Terry L. (Inventor); DeLucas, Lawrence J. (Inventor); Hamrick, David T. (Inventor)

2007-01-01

An improved method of screening crystal growth conditions is provided wherein molecules are crystallized from solutions containing dyes. These dyes are selectively incorporated or associated with crystals of particular character thereby rendering crystals of particular character colored and improving detection of the dyed crystals. A preferred method involves use of dyes in protein solutions overlayed by oil. Use of oil allows the use of small volumes of solution and facilitates the screening of large numbers of crystallization conditions in arrays using automated devices that dispense appropriate solutions to generate crystallization trials, overlay crystallization trials with an oil, provide appropriate conditions conducive to crystallization and enhance detection of dyed (colored) or undyed (uncolored) crystals that result.

Influence of annealing temperature on optical properties of Al doped ZnO nanoparticles via sol-gel methods

NASA Astrophysics Data System (ADS)

Rashid, Affa Rozana Abd; Hazwani, Tuan Nur; Mukhtar, Wan Maisarah; Taib, Nur Athirah Mohd

2018-06-01

Zinc oxide (ZnO) thin films have become technologically important materials due to their wide range of electrical and optical properties. The characteristics can be further adjusted by adequate doping processes. The effect of dopant concentration of Al, heating treatment and annealing in reducing atmosphere on the optical properties of the thin films is discussed. Undoped and aluminum-doped zinc oxide (AZO) thin films are prepared by the sol-gel method. Zinc acetate dihydrate, 2-methoxyethanol and monoethanolamine are used as precursor, solvent and stabilizer. In the case of AZO, aluminum nitrate nanohydrate is added to the precursor solution with an atomic percentage equal to 0 %, 1 %, 2 % and 3 % of Al. The multi thin layers are transformed into ZnO upon annealing at 450 °C and 500 °C. The optical properties such as transmittance, absorbance, band gap and refractive index of the thin films have been investigated by using UV-Visible Spectroscopy (UV-Vis). The results show that the effect of aluminium dopant concentration on the optical properties is depend on the post-heat treatment of the films. By doping with Al, the transmittance spectra in visible range increased and widen the band gap of ZnO which might due to Burstein-moss effects.

Hydrogen storage studies on palladium-doped carbon materials (AC, CB, CNMs) @ metal-organic framework-5.

PubMed

Viditha, V; Srilatha, K; Himabindu, V

2016-05-01

Metal organic frameworks (MOFs) are a rapidly growing class of porous materials and are considered as best adsorbents for their high surface area and extraordinary porosity. The MOFs are synthesized by using various chemicals like triethylamine, terepthalic acid, zinc acetate dihydrate, chloroform, and dimethylformamide (DMF). Synthesized MOFs are intercalated with palladium/activated carbon, carbon black, and carbon nanomaterials by chemical reduction method for the purpose of enhancing the hydrogen adsorption capacities. We have observed that the palladium doped activated carbon on MOF-5 showed high hydrogen storage capacity. This may be due to the affinity of the palladium toward hydrogen molecule. The samples are characterized by X-ray diffraction, scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET) surface area analysis. We have observed a clear decrease in the BET surface area and pore volume. The obtained results show a better performance for the synthesized sample. To our best knowledge, no one has reported the work on palladium-doped carbon materials (activated carbon, carbon black, carbon nanomaterials) impregnated to the metal-organic framework-5. We have attempted to synthesize carbon nanomaterials using indigenously fabricated chemical vapor deposition (CVD) unit as a support. We have observed an increase in the hydrogen storage capacities.

Effects of 2 adenosine antagonists, quercetin and caffeine, on vigilance and mood.

PubMed

Olson, Craig A; Thornton, Jennifer A; Adam, Gina E; Lieberman, Harris R

2010-10-01

Quercetin, a phenolic flavonoid found in small quantities in some fruits and vegetables, is an adenosine receptor antagonist in vitro marketed as a dietary supplement for purported caffeine-like effects. A double-blind, placebo-controlled, between-subjects study was conducted to compare the behavioral effects of quercetin to a central adenosine receptor antagonist, caffeine. Fifty-seven volunteers received either 2000 mg of quercetin dihydrate (a dose estimated based on in vitro receptor binding to be equivalent in potency to 200 mg of caffeine), placebo, or 200 mg of caffeine. One hour later, a 45-minute visual vigilance task was administered. The Profile of Mood States questionnaire was completed before treatment and immediately after vigilance testing. On the vigilance task, caffeine increased the number of stimuli detected (P < 0.02) and decreased the reaction time (P = 0.001). Caffeine increased self-reported vigor and reduced fatigue and total mood disturbance Profile of Mood States scores compared with placebo. Quercetin did not significantly alter any parameter, but values were typically intermediate between caffeine and placebo on those tests affected by caffeine. Quercetin is unlikely to have any effects when consumed by humans in quantities present in the diet or in dietary supplements. Caffeine (200 mg) administration resulted in the expected effects on vigilance and mood.

Effects of ancillary ligands on selectivity of protein labeling with platinum(II) chloro complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Xia-Ying.

1990-02-01

Potassium (2,6-pyridinedicarboxylato)chloroplatinate(II) was synthesized. The molecular structure of the complex in (n-Bu){sub 4}N(Pt(dipic)Cl){center dot}0.5H{sub 2}O was determined by x-ray crystallography. The (Pt(dipic)Cl){sup {minus}} is essentially planar and contains a Pt(II) atom, a tridentate dipicolinate dianion ligand, and a unidentate Cl{sup {minus}} ligand. The bis(bidentate) complex trans-(Pt(dipic){sub 2}){sup 2{minus}} was also observed by {sup 1}H NMR. A red gel-like substance was observed when the yellow aqueous solution of K(Pt(dipic)Cl) was cooled or concentrated. The K(Pt(dipic)Cl) molecules form stacks in the solid state and gel-like substance but remain monomeric over a wide range of concentrations and temperatures. The reactivity and selectivity of(Pt(dipic)Cl){supmore » {minus}} toward cytochromes c from horse and tuna were studied. The new transition-metal reagent is specific for methionine residues. Di(2-pyridyl-{beta}-ethyl)sulfidochloroplatinum(II) chloride dihydrate was also synthesized. This complex labels histidine and methionine residues in cytochrome c. The ancillary ligands in these platinum(II) complexes clearly determine the selectivity of protein labeling. 106 refs., 10 figs., 11 tabs.« less

ACR Appropriateness Criteria® Chronic Extremity Joint Pain-Suspected Inflammatory Arthritis.

PubMed

Jacobson, Jon A; Roberts, Catherine C; Bencardino, Jenny T; Appel, Marc; Arnold, Erin; Baccei, Steven J; Cassidy, R Carter; Chang, Eric Y; Fox, Michael G; Greenspan, Bennett S; Gyftopoulos, Soterios; Hochman, Mary G; Mintz, Douglas N; Newman, Joel S; Rosenberg, Zehava S; Shah, Nehal A; Small, Kirstin M; Weissman, Barbara N

2017-05-01

Evaluation for suspected inflammatory arthritis as a cause for chronic extremity joint pain often relies on imaging. This review first discusses the characteristic osseous and soft tissue abnormalities seen with inflammatory arthritis and how they may be imaged. It is essential that imaging results are interpreted in the context of clinical and serologic results to add specificity as there is significant overlap of imaging findings among the various types of arthritis. This review provides recommendations for imaging evaluation of specific types of inflammatory arthritis, including rheumatoid arthritis, seronegative spondyloarthropathy, gout, calcium pyrophosphate dihydrate disease (or pseudogout), and erosive osteoarthritis. The American College of Radiology Appropriateness Criteria are evidence-based guidelines for specific clinical conditions that are reviewed annually by a multidisciplinary expert panel. The guideline development and revision include an extensive analysis of current medical literature from peer-reviewed journals and the application of well-established methodologies (RAND/UCLA Appropriateness Method and Grading of Recommendations Assessment, Development, and Evaluation or GRADE) to rate the appropriateness of imaging and treatment procedures for specific clinical scenarios. In those instances where evidence is lacking or equivocal, expert opinion may supplement the available evidence to recommend imaging or treatment. Copyright © 2017 American College of Radiology. Published by Elsevier Inc. All rights reserved.

One-step polypyrrole coating of self-assembled silver nanoprisms for enhanced stability and Raman scattering

NASA Astrophysics Data System (ADS)

Jeong, Dong-Won; Jeong, Sugyeong; Jang, Du-Jeon

2017-07-01

Self-assemblies of silver nanoprisms (AgPRs) having enhanced structural stability and optical properties have been facilely coated with polypyrrole (PPy) via the in situ polymerization of pyrrole monomers that also act as an assembling agent. The assemblies of AgPRs, whose edge lengths and thicknesses are typically 78 and 4 nm, respectively, have been surrounded by a PPy coating of 6 nm. AgPRs are assembled in a side-to-side orientation, and the degree of assembly has been controlled by varying the concentration of trisodium citrate dihydrate, which attaches selectively to the {111} facets of AgPRs. The morphology deformation time of PPy-coated AgPRs in 0.6 mM H2O2(aq) is seven times longer than that of PPy-free AgPRs, suggesting that PPy coating prevents the sharp tips of AgPRs from being truncated by oxidizing agents. The SERS effect of highly self-assembled and PPy-coated AgPRs becomes as high as 6.3 due to numerous hot spots generated between nanoprisms. Overall, our fabricated AgPRs assemblies with PPy coating have not only improved structural stability but also enhanced optical properties, extending the practical use of noble-metal nanoprisms for various optical applications.

Synthesis and spectral characterization of Zn(II) microsphere series for antimicrobial application

NASA Astrophysics Data System (ADS)

Singh, Ajay K.; Pandey, Sarvesh K.; Pandey, O. P.; Sengupta, S. K.

2014-09-01

Microsphere series have been synthesized by reacting zinc(II) acetate dihydrate with Schiff bases derived from 2-hydrazino-5-[substituted phenyl]-1,3,4-thiadiazole/oxadiazole/triazole with salicylaldehyde. Elemental analysis suggests that the complexes have 1:2 and 1:1 stoichiometry of the type [Zn(L)2(H2O)2] and [Zn(L‧)(H2O)2]; LH = Schiff bases derived from 2-hydrazino-5-[substituted phenyl]-1,3,4-thia/oxadiazole with salicylaldehyde; L‧H2 = Schiff bases derived from 3-(substituted phenyl)-4-amino-5-hydrazino-1,2,4-triazole and salicylaldehyde and were characterized by elemental analyses, IR, 1H NMR and 13C NMR spectral data. Scanning electron microscopy (SEM) showed that synthesized materials have microsphere like structure and there EDX analysis comparably matches with elemental analysis. For the antimicrobial application Schiff bases and their zinc(II) complexes were screened for four bacteria e.g. Bacillus subtilis, Pseudomonas aeruginosa, Salmonella typhi, Streptococcus pyogenes and four fungi e.g. Cyrtomium falcatum, Aspergillus niger, Fusarium oxysporium and Curvularia pallescence by the reported method. Schiff base and Zn(II) compounds showed significant antimicrobial activities. However, activities increase upon chelation. Thermal analysis (TGA) data of compound (10) showed its stability up to 300 °C.

Co-spray Drying with HPMC as a Platform to Improve Direct Compaction Properties of Various Tablet Fillers.

PubMed

Li, JinZhi; Zhao, LiJie; Lin, Xiao; Shen, Lan; Feng, Yi

2017-11-01

Many commonly used tablet fillers are not suitable for direct compaction process due to insufficient properties, mainly of flowability and compactability. This work therefore aimed to use co-spray drying with HPMC as a platform to improve direct compaction properties of various tablet fillers. Starch, calcium hydrogen phosphate dihydrate (DCPD), and mannitol were chosen as a representative of three types of commonly used fillers (i.e. organic macromolecules, water-insoluble inorganic salts, and water-soluble small molecular carbohydrates), respectively. The five-level central composite design-response surface methodology was used (i) to investigate the effects of HPMC level and solid content of the feed on various powder, tableting, and tablet properties of composite excipients, and (ii) to optimize the composition. The results showed that the impacts of the two factors on various properties of composite excipients showed great similarity, despite of significantly different primary properties of the parent fillers, and the HPMC level was the main contributor to the majority of the impacts. An increase in HPMC level significantly improved tablet tensile strength and various tableting parameters. For all the three fillers, their optimized composite excipients provided by the established models showed excellent performances as predicted. The platform suggested is confirmed to be effective and promising.

Preparation of micro/nano-fibrous brushite coating on titanium via chemical conversion for biomedical applications

NASA Astrophysics Data System (ADS)

Liu, Bing; Guo, Yong-yuan; Xiao, Gui-yong; Lu, Yu-peng

2017-03-01

Calcium phosphate coatings have been applied on the surface of Ti implants to realize better osseointegration. The formation of dicalcium phosphate dihydrate (CaHPO4·2H2O), mineralogically named brushite on pure Ti substrate has been investigated via chemical conversion method. Coating composition and microstructure have been investigated by X-ray diffractometer, Fourier transform infrared spectrometer and field emission scanning electron microscope. The results reveal that the coatings are composed of high crystalline brushite with minor scholzite (CaZn2(PO4)2·2H2O). A micro/nano-scaled fibrous morphology can be produced in the acidic chemical conversion bath with pH 5.00. The surface of the fibrous brushite coating exhibits high hydrophilicity and corrosion resistance in the simulated body fluid. The osteoblast cells grow and spread actively on the coated samples and the proliferation numbers and alkaline phosphate activities of the cells improve significantly compared to the uncoated Ti. It is suggested that the micro/nano-fibrous brushite coating can be a potential approach to improve the osteoinductivity and osteoconductivity of Ti implant, due to its similarity in morphology and dimension to inorganic components of biological hard tissues, and favorable responses to the osteoblasts.

The development of carbamazepine-succinic acid cocrystal tablet formulations with improved in vitro and in vivo performance.

PubMed

Ullah, Majeed; Hussain, Izhar; Sun, Changquan Calvin

2016-01-01

The use of soluble cocrystal for delivering drugs with low solubility, although a potentially effective approach, often suffers the problem of rapid disproportionation during dissolution, which negates the solubility advantages offered by the cocrystal. This necessitates their robust stabilization in order for successful use in a tablet dosage form. The cocrystal between carbamezepine and succinic acid (CBZ-SUC) exhibits a higher aqueous solubility than its dihydrate, which is the stable form of CBZ in water. Using this model system, we demonstrate an efficient and material-sparing tablet formulation screening approach enabled by intrinsic dissolution rate measurements. Three tablet formulations capable of stabilizing the cocrystal both under accelerated condition of 40 °C and 75% RH and during dissolution were developed using three different polymers, Soluplus® (F1), Kollidon VA/64 (F2) and Hydroxypropyl methyl cellulose acetate succinate (F3). When compared to a marketed product, Epitol® 200 mg tablets (F0), drug release after 60 min from formulations F1 (∼82%), F2 (∼95%) and F3 (∼95%) was all higher than that from Epitol® (79%) in a modified simulated intestinal fluid. Studies in albino rabbits show correspondingly better bioavailability of F1-F3 than Epitol.

Manufacturing process, characterization and optical investigation of amorphous 1D zinc oxide nanostructures

NASA Astrophysics Data System (ADS)

Matysiak, Wiktor; Tański, Tomasz; Zaborowska, Marta

2018-06-01

The purpose of this article was to produce amorphous ZnO nanowires via the electrospinning process from a polyvinylpyrrolidone (PVP)/zinc acetate dihydrate (Zn(COOH)2)/dimethylformamide (DMF) and ethanol (EtOH) solution. The as obtained nanofibers were calcined at temperatures ranging from 400 to 600 °C to remove the organic phase. The one-dimensional zinc oxide nanostructures were studied using a scanning electron microscope (SEM) and a transmission electron microscope (TEM) to analyse the influence of the used temperature on the morphology and structures of the obtained ceramic nanomaterials. In order to examine the chemical structure of nanowires, the energy dispersive spectrometry (EDX) was used. Besides, a thermogravimetric analysis (TGA) was performed to show the polymer concentration loss in a function of temperature in order to obtain pure zinc oxide nanowires. The optical property analysis was performed on the basis of UV-vis spectra of absorbance as a function of the wavelength. Using the modified Swanepoel method, which the authors proposed, and the recorded absorbance spectra determined the banded refractive index n, real n‧ and imaginary k part of the refractive index as a function of the wavelength, complex dielectric permeability ɛ, real and imaginary part εr and εi of the dielectric permeability as a function of the radiation energy of the produced ZnO nanowires.

Fabrication of mineralized electrospun PLGA and PLGA/gelatin nanofibers and their potential in bone tissue engineering.

PubMed

Meng, Z X; Li, H F; Sun, Z Z; Zheng, W; Zheng, Y F

2013-03-01

Surface mineralization is an effective method to produce calcium phosphate apatite coating on the surface of bone tissue scaffold which could create an osteophilic environment similar to the natural extracellular matrix for bone cells. In this study, we prepared mineralized poly(D,L-lactide-co-glycolide) (PLGA) and PLGA/gelatin electrospun nanofibers via depositing calcium phosphate apatite coating on the surface of these nanofibers to fabricate bone tissue engineering scaffolds by concentrated simulated body fluid method, supersaturated calcification solution method and alternate soaking method. The apatite products were characterized by the scanning electron microscopy (SEM), Fourier transform-infrared spectroscopy (FT-IR), and X-ray diffractometry (XRD) methods. A large amount of calcium phosphate apatite composed of dicalcium phosphate dihydrate (DCPD), hydroxyapatite (HA) and octacalcium phosphate (OCP) was deposited on the surface of resulting nanofibers in short times via three mineralizing methods. A larger amount of calcium phosphate was deposited on the surface of PLGA/gelatin nanofibers rather than PLGA nanofibers because gelatin acted as nucleation center for the formation of calcium phosphate. The cell culture experiments revealed that the difference of morphology and components of calcium phosphate apatite did not show much influence on the cell adhesion, proliferation and activity. Copyright © 2012 Elsevier B.V. All rights reserved.

Organization and mobility of water in amorphous and crystalline trehalose

NASA Astrophysics Data System (ADS)

Kilburn, Duncan; Townrow, Sam; Meunier, Vincent; Richardson, Robert; Alam, Ashraf; Ubbink, Job

2006-08-01

The disaccharide trehalose is accumulated by microorganisms, such as yeasts, and multicellular organisms, such as tardigrades, when conditions of extreme drought occur. In this way these organisms can withstand dehydration through the formation of an intracellular carbohydrate glass, which, with its high viscosity and hydrogen-bonding interactions, stabilizes and protects the integrity of complex biological structures and molecules. This property of trehalose can also be harnessed in the stabilization of liposomes, proteins and in the preservation of red blood cells, but the underlying mechanism of bioprotection is not yet fully understood. Here we use positron annihilation lifetime spectroscopy to probe the free volume of trehalose matrices; specifically, we develop a molecular picture of the organization and mobility of water in both amorphous and crystalline states. Whereas in amorphous matrices, water increases the average intermolecular hole size, in the crystalline dihydrate it is organized as a confined one-dimensional fluid in channels of fixed diameter that allow activated diffusion of water in and out of the crystallites. We present direct real-time evidence of water molecules unloading reversibly from these channels, thereby acting as both a sink and a source of water in low-moisture systems. We postulate that this behaviour may provide the overall stability required to keep organisms viable through dehydration conditions.

Can a dual-energy computed tomography predict unsuitable stone components for extracorporeal shock wave lithotripsy?

PubMed

Ahn, Sung Hoon; Oh, Tae Hoon; Seo, Ill Young

2015-09-01

To assess the potential of dual-energy computed tomography (DECT) to identify urinary stone components, particularly uric acid and calcium oxalate monohydrate, which are unsuitable for extracorporeal shock wave lithotripsy (ESWL). This clinical study included 246 patients who underwent removal of urinary stones and an analysis of stone components between November 2009 and August 2013. All patients received preoperative DECT using two energy values (80 kVp and 140 kVp). Hounsfield units (HU) were measured and matched to the stone component. Significant differences in HU values were observed between uric acid and nonuric acid stones at the 80 and 140 kVp energy values (p<0.001). All uric acid stones were red on color-coded DECT images, whereas 96.3% of the nonuric acid stones were blue. Patients with calcium oxalate stones were divided into two groups according to the amount of monohydrate (calcium oxalate monohydrate group: monohydrate≥90%, calcium oxalate dihydrate group: monohydrate<90%). Significant differences in HU values were detected between the two groups at both energy values (p<0.001). DECT improved the characterization of urinary stone components and was a useful method for identifying uric acid and calcium oxalate monohydrate stones, which are unsuitable for ESWL.

Adsorption behavior of methacryloyloxydecyl dihydrogen phosphate on an apatite surface at neutral pH.

PubMed

Bista, Baba; Nakashima, Syozi; Nikaido, Toru; Sadr, Alireza; Takagaki, Tomohiro; Romero, Maria J R H; Sato, Takaaki; Tagami, Junji

2016-04-01

This study aimed to quantify the adsorption affinity of neutralized 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP-N) toward hydroxyapatite (HA) and dicalcium phosphate dihydrate (DCPD) at pH 7.0 by employing the Langmuir isotherm model. Furthermore, the effects of inorganic phosphate (Pi) and fluoride (F(-) ) ions on the adsorption of 10-MDP-N onto HA and DCPD were examined. Fixed amounts of HA and DCPD powders were suspended in different concentrations of 10-MDP-N solutions and were incubated for 18 h. Equilibrated concentrations of 10-MDP-N were measured by spectrophotometry and the adsorption affinity was estimated using the Langmuir model. Moreover, the adsorption was examined by zeta-potential analysis. The results indicated that significant Langmuir correlation was noted in both substrates, along with an increasing negative zeta-potential; however, in DCPD the correlation was less strong. The addition of 1.0 mM Pi slightly delayed the adsorption of 10-MDP-N onto both substrates, whereas 3.0 mM Pi drastically delayed adsorption onto HA but completely inhibited adsorption onto DCPD. Up to 50 ppm, F(-) enhanced the adsorption onto HA, and the adsorption plateaued at higher concentrations of F(-) , whereas no obvious influence of F(-) on the adsorption onto DCPD was noted. © 2016 Eur J Oral Sci.

Preparation of 7-hydroxy-2-oxoindolin-3-ylacetic acid and its [13C2], [5-n-3H], and [5-n-3H]-7-O-glucosyl analogues for use in the study of indol-3-ylacetic acid catabolism

NASA Technical Reports Server (NTRS)

Lewer, P.; Bandurski, R. S. (Principal Investigator)

1987-01-01

An improved synthesis of 7-hydroxy-2-oxoindolin-3-ylacetic acid via the base-induced condensation reaction between oxalate esters and 7-benzyloxyindolin-2-one is described. 7-Benzyloxyindolin-2-one was prepared in four steps and 50% overall yield from 3-hydroxy-2-nitrotoluene. The yield of the title compound from 7-benzyloxyindolin-2-one was 56%. This route was used to prepare 7-hydroxy-2-oxoindolin-3-yl[13C2]acetic acid in 30% yield from [13C2]oxalic acid dihydrate. The method could not be extended to the preparation of the corresponding [14C2]-compound. However, an enzyme preparation from Zea mays roots catalysed the conversion of carrier-free [5-n-3H]indol-3-ylacetic acid with a specific activity of 16.7 Ci mmol-1 to a mixture of 7-hydroxy-2-oxo[5-n-3H]indolin-3-ylacetic acid and its [5-n-3H]-7-O-glucoside in ca. 3 and 40% radiochemical yield respectively. The glucoside was converted into the 7-hydroxy compound in 80% yield by means of beta-glucosidase.

Fabrication of interconnected porous β-tricalcium phosphate (β-TCP) based on a setting reaction of β-TCP granules with HNO3 followed by heat treatment.

PubMed

Ishikawa, Kunio; Putri, Tansza Setiana; Tsuchiya, Akira; Tanaka, Keisuke; Tsuru, Kanji

2018-03-01

β-Tricalcium phosphate [β-TCP] is the typical bone substitute due to its excellent osteoconductivity and bioresorbability. One of the keys to improve its potential as bone substitute is to introduce porous structure and its regulation. In this study, interconnected porous β-TCP blocks were fabricated through a setting reaction of β-TCP granules and subsequent heat treatment. First, β-TCP granules were mixed with HNO 3 . Upon mixing, β-TCP granules were bridged with dicalcium phosphate dihydrate [DCPD: CaHPO 4 ·2H 2 O] containing Ca(NO 3 ) 2 . Then, the DCPD-bridged β-TCP was heated at 1100°C. During the heating process, DCPD containing Ca(NO 3 ) 2 transformed into β-TCP and bonded with β-TCP granules. As a result, an interconnected porous β-TCP block formed. The diametral tensile strength and porosity of the interconnected porous β-TCP block fabricated from 200-300-μm β-TCP granules and 5 N HNO 3 and then heated at 1,100°C were 1.4 ± 0.2 MPa and 57% ± 2%, respectively. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 797-804, 2018. © 2017 Wiley Periodicals, Inc.

Ammonia-water mixtures at high pressures - Melting curves of ammonia dihydrate and ammonia monohydrate and a revised high-pressure phase diagram for the water-rich region. [in primordial solar system ices

NASA Technical Reports Server (NTRS)

Boone, S.; Nicol, M. F.

1991-01-01

The phase relations of some mixtures of ammonia and water are investigated to create a phase diagram in pressure-temperature-composition space relevant to the geophysical study of bodies in the outer solar system. The mixtures of NH3(x)H2O(1-x), where x is greater than 0.30 but less than 0.51, are examined at pressures and temperatures ranging from 0-6.5 GPa and 125-400 K, respectively. The ruby luminescence technique monitors the pressure and a diamond-anvil cell compresses the samples, and the phases are identified by means of normal- and polarized-light optical microscopy. The melting curve for NH3H2O(2) is described by the equation T = 176 + 60P - 8.5P squared for the ranges of 0.06-1.4 GPa and 179-243 K. The equation for NH3H2O is T = 194 + 37P - P squared, which represents a minor correction of a previous description by Johnson et al. (1985). Observed phase transitions are consistent with the high-pressure stability limit of NH3H2O(2), and the transition boundary is found to be linear.

Effects of coformers on phase transformation and release profiles of carbamazepine cocrystals in hydroxypropyl methylcellulose based matrix tablets.

PubMed

Qiu, Shi; Li, Mingzhong

2015-02-01

The aim of this study was to investigate the effects of coformers on phase transformation and release profiles of carbamazepine (CBZ) cocrystals in hydroxypropyl methylcellulose (HPMC) based matrix tablets. It has been found that selection of different coformers of saccharin (SAC) and cinnamic acid (CIN) can affect the stability of CBZ cocrystals in solution, resulting in significant differences in the apparent solubility of CBZ. The dissolution advantage of CBZ-SAC cocrystals can only be shown for a short period during dissolution because of the fast conversion to its dihydrate form (DH). HPMC can partially inhibit the crystallisation of CBZ DH during dissolution of CBZ-SAC cocrystal. However, the increased viscosity of HPMC dissolution medium reduced the dissolution rate of CBZ-SAC cocrystals. Therefore the CBZ-SAC cocrystal formulation did not show any significant advantage in CBZ release rate. In contrast the improved CBZ dissolution rate of CBZ-CIN cocrystal can be realised in both solution and formulation due to its high stability. In conclusion, exploring and understanding the mechanisms of the phase transformation of pharmaceutical cocrystals in aqueous medium for selection of lead cocrystals is the key for success of product development. Copyright © 2014 Elsevier B.V. All rights reserved.

The Remedial Efficacy of Spirulina platensis versus Chromium-Induced Nephrotoxicity in Male Sprague-Dawley Rats

PubMed Central

Elshazly, M. O.; Abd El-Rahman, Sahar S.; Morgan, Ashraf M.; Ali, Merhan E.

2015-01-01

This study was conducted to investigate the possible protective effect of Spirulina platensis against chromium-induced nephrotoxicity. A total of 36 adult male Sprague-Dawley rats were divided into 4 equal groups (Gps). Gp1 served as control, rats of Gps 2, 3, and 4 were exposed to Spirulina platensis (300 mg/kg b.wt per os) and sodium dichromate dihydrate (SDD) via drinking water at concentration of 520 mg /l respectively. Chromium administration caused alterations in the renal function markers as evidenced by significant increase of blood urea and creatinine levels accompanied with significant increase in kidney’s chromium residues and MDA level as well as decreased catalase activity and glutathion content in kidney tissue. Histologically, Cr provoked deleterious changes including: vascular congestion, wide spread tubular epithelium necrobiotic changes, atrophy of glomerular tuft and proliferative hyperplasia. The latter was accompanied with positive PCNA expression in kidney tissues as well as DNA ploidy interpretation of major cellular population of degenerated cells, appearance of tetraploid cells, high proliferation index and high DNA index. Morphometrical measurements revealed marked glomerular and tubular lumen alterations. On contrary, spirulina co-treatment with Cr significantly restored the histopathological changes, antioxidants and renal function markers and all the previously mentioned changes as well. PMID:26029926

The Remedial Efficacy of Spirulina platensis versus Chromium-Induced Nephrotoxicity in Male Sprague-Dawley Rats.

PubMed

Elshazly, M O; Abd El-Rahman, Sahar S; Morgan, Ashraf M; Ali, Merhan E

2015-01-01

This study was conducted to investigate the possible protective effect of Spirulina platensis against chromium-induced nephrotoxicity. A total of 36 adult male Sprague-Dawley rats were divided into 4 equal groups (Gps). Gp1 served as control, rats of Gps 2, 3, and 4 were exposed to Spirulina platensis (300 mg/kg b.wt per os) and sodium dichromate dihydrate (SDD) via drinking water at concentration of 520 mg /l respectively. Chromium administration caused alterations in the renal function markers as evidenced by significant increase of blood urea and creatinine levels accompanied with significant increase in kidney's chromium residues and MDA level as well as decreased catalase activity and glutathion content in kidney tissue. Histologically, Cr provoked deleterious changes including: vascular congestion, wide spread tubular epithelium necrobiotic changes, atrophy of glomerular tuft and proliferative hyperplasia. The latter was accompanied with positive PCNA expression in kidney tissues as well as DNA ploidy interpretation of major cellular population of degenerated cells, appearance of tetraploid cells, high proliferation index and high DNA index. Morphometrical measurements revealed marked glomerular and tubular lumen alterations. On contrary, spirulina co-treatment with Cr significantly restored the histopathological changes, antioxidants and renal function markers and all the previously mentioned changes as well.

Chromium and Ruthenium-Doped Zinc Oxide Thin Films for Propane Sensing Applications

PubMed Central

Gómez-Pozos, Heberto; González-Vidal, José Luis; Torres, Gonzalo Alberto; Rodríguez-Baez, Jorge; Maldonado, Arturo; de la Luz Olvera, María; Acosta, Dwight Roberto; Avendaño-Alejo, Maximino; Castañeda, Luis

2013-01-01

Chromium and ruthenium-doped zinc oxide (ZnO:Cr) and (ZnO:Ru) thin solid films were deposited on soda-lime glass substrates by the sol-gel dip-coating method. A 0.6 M solution of zinc acetate dihydrate dissolved in 2-methoxyethanol and monoethanolamine was used as basic solution. Chromium (III) acetylacetonate and Ruthenium (III) trichloride were used as doping sources. The Ru incorporation and its distribution profile into the films were proved by the SIMS technique. The morphology and structure of the films were studied by SEM microscopy and X-ray diffraction measurements, respectively. The SEM images show porous surfaces covered by small grains with different grain size, depending on the doping element, and the immersions number into the doping solutions. The sensing properties of ZnO:Cr and ZnO:Ru films in a propane (C3H8) atmosphere, as a function of the immersions number in the doping solution, have been studied in the present work. The highest sensitivity values were obtained for films doped from five immersions, 5.8 and 900, for ZnO:Cr and ZnO:Ru films, respectively. In order to evidence the catalytic effect of the chromium (Cr) and ruthenium (Ru), the sensing characteristics of undoped ZnO films are reported as well. PMID:23482091

Silicone intraocular lens surface calcification in a patient with asteroid hyalosis.

PubMed

Matsumura, Kazuhiro; Takano, Masahiko; Shimizu, Kimiya; Nemoto, Noriko

2012-07-01

To confirm a substance presence on the posterior intraocular lens (IOL) surface in a patient with asteroid hyalosis. An 80-year-old man had IOLs for approximately 12 years. Opacities and neodymium-doped yttrium aluminum garnet pits were observed on the posterior surface of the right IOL. Asteroid hyalosis and an epiretinal membrane were observed OD. An IOL exchange was performed on 24 March 2008, and the explanted IOL was analyzed using a light microscope and a transmission electron microscope with a scanning electron micrograph and an energy-dispersive X-ray spectrometer for elemental analysis. To confirm asteroid hyalosis, asteroid bodies were examined with the ionic liquid (EtMeIm+ BF4-) method using a field emission scanning electron microscope (FE-SEM) with digital beam control RGB mapping. X-ray spectrometry of the deposits revealed high calcium and phosphorus peaks. Spectrometry revealed that the posterior IOL surface opacity was due to a calcium-phosphorus compound. Examination of the asteroid bodies using FE-SEM with digital beam control RGB mapping confirmed calcium and phosphorus as the main components. Calcium hydrogen phosphate dihydrate deposits were probably responsible for the posterior IOL surface opacity. Furthermore, analysis of the asteroid bodies demonstrated that calcium and phosphorus were its main components.

Modeling of Mechanical Stress Exerted by Cholesterol Crystallization on Atherosclerotic Plaques.

PubMed

Luo, Yuemei; Cui, Dongyao; Yu, Xiaojun; Chen, Si; Liu, Xinyu; Tang, Hongying; Wang, Xianghong; Liu, Linbo

2016-01-01

Plaque rupture is the critical cause of cardiovascular thrombosis, but the detailed mechanisms are not fully understood. Recent studies have found abundant cholesterol crystals in ruptured plaques, and it has been proposed that the rapid expansion of cholesterol crystals in a limited space during crystallization may contribute to plaque rupture. To evaluate the effect of cholesterol crystal growth on atherosclerotic plaques, we modeled the expansion of cholesterol crystals during the crystallization process in the necrotic core and estimated the stress on the thin cap with different arrangements of cholesterol crystals. We developed a two-dimensional finite element method model of atherosclerotic plaques containing expanding cholesterol crystals and investigated the effect of the magnitude and distribution of crystallization on the peak circumferential stress born by the cap. Using micro-optical coherence tomography (μOCT), we extracted the cross-sectional geometric information of cholesterol crystals in human atherosclerotic aorta tissue ex vivo and applied the information to the model. The results demonstrate that (1) the peak circumference stress is proportionally dependent on the cholesterol crystal growth; (2) cholesterol crystals at the cap shoulder impose the highest peak circumference stress; and (3) spatial distributions of cholesterol crystals have a significant impact on the peak circumference stress: evenly distributed cholesterol crystals exert less peak circumferential stress on the cap than concentrated crystals.

Stepwise crystallization and the layered distribution in crystallization kinetics of ultra-thin poly(ethylene terephthalate) film

NASA Astrophysics Data System (ADS)

Zuo, Biao; Xu, Jianquan; Sun, Shuzheng; Liu, Yue; Yang, Juping; Zhang, Li; Wang, Xinping

2016-06-01

Crystallization is an important property of polymeric materials. In conventional viewpoint, the transformation of disordered chains into crystals is usually a spatially homogeneous process (i.e., it occurs simultaneously throughout the sample), that is, the crystallization rate at each local position within the sample is almost the same. Here, we show that crystallization of ultra-thin poly(ethylene terephthalate) (PET) films can occur in the heterogeneous way, exhibiting a stepwise crystallization process. We found that the layered distribution of glass transition dynamics of thin film modifies the corresponding crystallization behavior, giving rise to the layered distribution of the crystallization kinetics of PET films, with an 11-nm-thick surface layer having faster crystallization rate and the underlying layer showing bulk-like behavior. The layered distribution in crystallization kinetics results in a particular stepwise crystallization behavior during heating the sample, with the two cold-crystallization temperatures separated by up to 20 K. Meanwhile, interfacial interaction is crucial for the occurrence of the heterogeneous crystallization, as the thin film crystallizes simultaneously if the interfacial interaction is relatively strong. We anticipate that this mechanism of stepwise crystallization of thin polymeric films will allow new insight into the chain organization in confined environments and permit independent manipulation of localized properties of nanomaterials.

Stepwise crystallization and the layered distribution in crystallization kinetics of ultra-thin poly(ethylene terephthalate) film

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zuo, Biao, E-mail: chemizuo@zstu.edu.cn, E-mail: wxinping@yahoo.com; Xu, Jianquan; Sun, Shuzheng

2016-06-21

Crystallization is an important property of polymeric materials. In conventional viewpoint, the transformation of disordered chains into crystals is usually a spatially homogeneous process (i.e., it occurs simultaneously throughout the sample), that is, the crystallization rate at each local position within the sample is almost the same. Here, we show that crystallization of ultra-thin poly(ethylene terephthalate) (PET) films can occur in the heterogeneous way, exhibiting a stepwise crystallization process. We found that the layered distribution of glass transition dynamics of thin film modifies the corresponding crystallization behavior, giving rise to the layered distribution of the crystallization kinetics of PET films,more » with an 11-nm-thick surface layer having faster crystallization rate and the underlying layer showing bulk-like behavior. The layered distribution in crystallization kinetics results in a particular stepwise crystallization behavior during heating the sample, with the two cold-crystallization temperatures separated by up to 20 K. Meanwhile, interfacial interaction is crucial for the occurrence of the heterogeneous crystallization, as the thin film crystallizes simultaneously if the interfacial interaction is relatively strong. We anticipate that this mechanism of stepwise crystallization of thin polymeric films will allow new insight into the chain organization in confined environments and permit independent manipulation of localized properties of nanomaterials.« less

Solution-grown crystals for neutron radiation detectors, and methods of solution growth

DOEpatents

Zaitseva, Natalia; Carman, M Leslie; Payne, Steve

2014-10-28

An organic crystal according to one embodiment includes an organic crystal comprising diphenylacetylene and stilbene or a stilbene derivative, the crystal having physical characteristics of formation from solution, the organic crystal exhibiting a signal response signature for neutrons from a radioactive source. A system according to one embodiment includes an organic crystal comprising diphenylacetylene and stilbene or a stilbene derivative, the crystal having physical characteristics of formation from solution, the organic crystal exhibiting a signal response signature for neutrons from a radioactive source; and a photodetector for detecting the signal response of the organic crystal. Methods of making such crystals are also provided.

Crystallization characteristics of iron-rich glass ceramics prepared from nickel slag and blast furnace slag

NASA Astrophysics Data System (ADS)

Wang, Zhong-Jie; Ni, Wen; Li, Ke-Qing; Huang, Xiao-Yan; Zhu, Li-Ping

2011-08-01

The crystallization process of iron-rich glass-ceramics prepared from the mixture of nickel slag (NS) and blast furnace slag (BFS) with a small amount of quartz sand was investigated. A modified melting method which was more energy-saving than the traditional methods was used to control the crystallization process. The results show that the iron-rich system has much lower melting temperature, glass transition temperature ( T g), and glass crystallization temperature ( T c), which can result in a further energy-saving process. The results also show that the system has a quick but controllable crystallization process with its peak crystallization temperature at 918°C. The crystallization of augite crystals begins from the edge of the sample and invades into the whole sample. The crystallization process can be completed in a few minutes. A distinct boundary between the crystallized part and the non-crystallized part exists during the process. In the non-crystallized part showing a black colour, some sphere-shaped augite crystals already exist in the glass matrix before samples are heated to T c. In the crystallized part showing a khaki colour, a compact structure is formed by augite crystals.

The Effect of Temperature and Solution pH on the Nucleation of Tetragonal Lysozyme Crystals

NASA Technical Reports Server (NTRS)

Judge, Russell A.; Jacobs, Randolph S.; Frazier, Tyralynn; Snell, Edward H.; Pusey, Marc L.

1999-01-01

Part of the challenge of macromolecular crystal growth for structure determination is obtaining crystals with a volume suitable for x-ray analysis. In this respect an understanding of the effect of solution conditions on macromolecule nucleation rates is advantageous. This study investigated the effects of supersaturation, temperature, and pH on the nucleation rate of tetragonal lysozyme crystals. Batch crystallization plates were prepared at given solution concentrations and incubated at set temperatures over 1 week. The number of crystals per well with their size and axial ratios were recorded and correlated with solution conditions. Crystal numbers were found to increase with increasing supersaturation and temperature. The most significant variable, however, was pH; crystal numbers changed by two orders of magnitude over the pH range 4.0-5.2. Crystal size also varied with solution conditions, with the largest crystals obtained at pH 5.2. Having optimized the crystallization conditions, we prepared a batch of crystals under the same initial conditions, and 50 of these crystals were analyzed by x-ray diffraction techniques. The results indicate that even under the same crystallization conditions, a marked variation in crystal properties exists.

Surrogate Seeds For Growth Of Crystals

NASA Technical Reports Server (NTRS)

Shlichta, Paul J.

1989-01-01

Larger crystals of higher quality grown. Alternative method for starting growth of crystal involves use of seed crystal of different material instead of same material as solution. Intended for growing single-crystal proteins for experiments but applicable in general to growth of crystals from solutions and to growth of semiconductor or other crystals from melts.

Noncovalent Polymerization of Mesogens Crystallizes Lysozyme: Correlation between Nonamphiphilic Lyotropic Liquid Crystal Phase and Protein Crystal Formation

PubMed Central

Simon, Karen A.; Shetye, Gauri S.; Englich, Ulrich; Wu, Lei; Luk, Yan-Yeung

2011-01-01

Crystallization of proteins is important for fundamental studies and biopharmaceutical development but remains largely an empirical science. Here, we report the use of organic salts that can form a class of unusual non-amphiphilic lyotropic liquid crystals to crystallize the protein lysozyme. Certain non-amphiphilic organic molecules with fused aromatic rings and two charges can assemble into stable thread-like noncovalent polymers that may further form liquid crystal phases in water, traditionally termed chromonic liquid crystals. Using five of these mesogenic molecules as additives to induce protein crystallization, we discover that molecules that can form liquid crystal phases in water are highly effective at inducing the crystal formation of lysozyme, even at concentrations significantly lower than that required for forming liquid crystal phases. This result reveals an example of inducing protein crystallization by the molecular assembly of the additives, and is consistent with a new mechanism by which the strong hydration of an assembly process provides a gradual means to compete for the water molecules to enable solvated proteins to form crystals. PMID:21786812

Control of heat transfer in continuous-feeding Czochralski-silicon crystal growth with a water-cooled jacket

NASA Astrophysics Data System (ADS)

Zhao, Wenhan; Liu, Lijun

2017-01-01

The continuous-feeding Czochralski method is an effective method to reduce the cost of single crystal silicon. By promoting the crystal growth rate, the cost can be reduced further. However, more latent heat will be released at the melt-crystal interface under a high crystal growth rate. In this study, a water-cooled jacket was applied to enhance the heat transfer at the melt-crystal interface. Quasi-steady-state numerical calculation was employed to investigate the impact of the water-cooled jacket on the heat transfer at the melt-crystal interface. Latent heat released during the crystal growth process at the melt-crystal interface and absorbed during feedstock melting at the feeding zone was modeled in the simulations. The results show that, by using the water-cooled jacket, heat transfer in the growing crystal is enhanced significantly. Melt-crystal interface deflection and thermal stress increase simultaneously due to the increase of radial temperature at the melt-crystal interface. With a modified heat shield design, heat transfer at the melt-crystal interface is well controlled. The crystal growth rate can be increased by 20%.

Steering a crystallization process to reduce crystal polydispersity; case study of insulin crystallization

NASA Astrophysics Data System (ADS)

Nanev, Christo N.; Petrov, Kostadin P.

2017-12-01

The use of the classical nucleation-growth-separation principle (NGSP) was restricted hitherto to nucleation kinetics studies only. A novel application of the NGSP is proposed. To reduce crystal polydispersity internal seeding of equally-sized crystals is suggested, the advantage being avoidance of crystal grinding, sieving and any introduction of impurities. In the present study, size distributions of grown insulin crystals are interpreted retrospectively to select the proper nucleation stage parameters. The conclusion is that when steering a crystallization process aimed at reducing crystal polydispersity, the shortest possible nucleation stage duration has to be chosen because it renders the closest size distribution of the nucleated crystal seeds. Causes of inherent propensity to increasing crystal polydispersity during prolonged growth are also explored. Step sources of increased activity, present in some crystals while absent in others, are pointed as the major polydispersity cause. Insulin crystal morphology is also considered since it determines the dissolution rate of a crystalline medicine.

The Effect of Thermal Cycling on Crystal-Liquid Separation During Lunar Magma Ocean Differentiation

NASA Technical Reports Server (NTRS)

Mills, Ryan D.

2013-01-01

Differentiation of magma oceans likely involves a mixture of fractional and equilibrium crystallization [1]. The existence of: 1) large volumes of anorthosite in the lunar highlands and 2) the incompatible- rich (KREEP) reservoir suggests that fractional crystallization may have dominated during differentiation of the Moon. For this to have occurred, crystal fractionation must have been remarkably efficient. Several authors [e.g. 2, 3] have hypothesized that equilibrium crystallization would have dominated early in differentiation of magma oceans because of crystal entrainment during turbulent convection. However, recent numerical modeling [4] suggests that crystal settling could have occurred throughout the entire solidification history of the lunar magma ocean if crystals were large and crystal fraction was low. These results indicate that the crystal size distribution could have played an important role in differentiation of the lunar magma ocean. Here, I suggest that thermal cycling from tidal heating during lunar magma ocean crystallization caused crystals to coarsen, leading to efficient crystal-liquid separation.

Crystal Growth Technology

NASA Astrophysics Data System (ADS)

Scheel, Hans J.; Fukuda, Tsuguo

2004-06-01

This volume deals with the technologies of crystal fabrication, of crystal machining, and of epilayer production and is the first book on industrial and scientific aspects of crystal and layer production. The major industrial crystals are treated: Si, GaAs, GaP, InP, CdTe, sapphire, oxide and halide scintillator crystals, crystals for optical, piezoelectric and microwave applications and more. Contains 29 contributions from leading crystal technologists covering the following topics:

General aspects of crystal growth technology Silicon Compound semiconductors Oxides and halides Crystal machining Epitaxy and layer deposition Scientific and technological problems of production and machining of industrial crystals are discussed by top experts, most of them from the major growth industries and crystal growth centers. In addition, it will be useful for the users of crystals, for teachers and graduate students in materials sciences, in electronic and other functional materials, chemical and metallurgical engineering, micro-and optoelectronics including nanotechnology, mechanical engineering and precision-machining, microtechnology, and in solid-state sciences.

• Effect of method of crystallization on the IV-III and IV-II polymorphic transitions of ammonium nitrate.

  PubMed

  Vargeese, Anuj A; Joshi, Satyawati S; Krishnamurthy, V N

  2009-01-15

  A study has been undertaken on the effect of crystallization method on the IV<-->III transition of ammonium nitrate (AN). AN is crystallized in three different ways, viz. recrystallization, evaporative crystallization and melt crystallization. When the samples were crystallized from saturated aqueous solution, ideal crystals were formed, which behaved differently from the crystals formed from the other methods. The DTA examination of the crystals showed that the crystals have different transition behaviour. The moisture uptake of the samples determined were found to have influenced by the mode of crystallization. The samples were further analyzed by powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). The present study showed that the parameters like thermal history, number of previous transformations and moisture content have a very negligible influence on the IV<-->III transition of AN as compared to the method of crystallization.

• Crystal growth and annealing method and apparatus

  DOEpatents

  Gianoulakis, Steven E.; Sparrow, Robert

  2001-01-01

  A method and apparatus for producing crystals that minimizes birefringence even at large crystal sizes, and is suitable for production of CaF.sub.2 crystals. The method of the present invention comprises annealing a crystal by maintaining a minimal temperature gradient in the crystal while slowly reducing the bulk temperature of the crystal. An apparatus according to the present invention includes a thermal control system added to a crystal growth and annealing apparatus, wherein the thermal control system allows a temperature gradient during crystal growth but minimizes the temperature gradient during crystal annealing. An embodiment of the present invention comprises a secondary heater incorporated into a conventional crystal growth and annealing apparatus. The secondary heater supplies heat to minimize the temperature gradients in the crystal during the annealing process. The secondary heater can mount near the bottom of the crucible to effectively maintain appropriate temperature gradients.

• Solution-grown crystals for neutron radiation detectors, and methods of solution growth

  DOEpatents

  Zaitseva, Natalia P; Hull, Giulia; Cherepy, Nerine J; Payne, Stephen A; Stoeffl, Wolfgang

  2012-06-26

  A method according to one embodiment includes growing an organic crystal from solution, the organic crystal exhibiting a signal response signature for neutrons from a radioactive source. A system according to one embodiment includes an organic crystal having physical characteristics of formation from solution, the organic crystal exhibiting a signal response signature for neutrons from a radioactive source; and a photodetector for detecting the signal response of the organic crystal. A method according to another embodiment includes growing an organic crystal from solution, the organic crystal being large enough to exhibit a detectable signal response signature for neutrons from a radioactive source. An organic crystal according to another embodiment includes an organic crystal having physical characteristics of formation from solution, the organic crystal exhibiting a signal response signature for neutrons from a radioactive source, wherein the organic crystal has a length of greater than about 1 mm in one dimension.

• Comparative analysis of anti-polyglutamine Fab crystals grown on Earth and in microgravity.

  PubMed

  Owens, Gwen E; New, Danielle M; Olvera, Alejandra I; Manzella, Julia Ashlyn; Macon, Brittney L; Dunn, Joshua C; Cooper, David A; Rouleau, Robyn L; Connor, Daniel S; Bjorkman, Pamela J

  2016-10-01

  Huntington's disease is one of nine neurodegenerative diseases caused by a polyglutamine (polyQ)-repeat expansion. An anti-polyQ antigen-binding fragment, MW1 Fab, was crystallized both on Earth and on the International Space Station, a microgravity environment where convection is limited. Once the crystals returned to Earth, the number, size and morphology of all crystals were recorded, and X-ray data were collected from representative crystals. The results generally agreed with previous microgravity crystallization studies. On average, microgravity-grown crystals were 20% larger than control crystals grown on Earth, and microgravity-grown crystals had a slightly improved mosaicity (decreased by 0.03°) and diffraction resolution (decreased by 0.2 Å) compared with control crystals grown on Earth. However, the highest resolution and lowest mosaicity crystals were formed on Earth, and the highest-quality crystal overall was formed on Earth after return from microgravity.

• Comparative analysis of anti-polyglutamine Fab crystals grown on Earth and in microgravity

  PubMed Central

  Owens, Gwen E.; New, Danielle M.; Olvera, Alejandra I.; Manzella, Julia Ashlyn; Macon, Brittney L.; Dunn, Joshua C.; Cooper, David A.; Rouleau, Robyn L.; Connor, Daniel S.; Bjorkman, Pamela J.

  2016-01-01

  Huntington’s disease is one of nine neurodegenerative diseases caused by a polyglutamine (polyQ)-repeat expansion. An anti-polyQ antigen-binding fragment, MW1 Fab, was crystallized both on Earth and on the International Space Station, a microgravity environment where convection is limited. Once the crystals returned to Earth, the number, size and morphology of all crystals were recorded, and X-ray data were collected from representative crystals. The results generally agreed with previous microgravity crystallization studies. On average, microgravity-grown crystals were 20% larger than control crystals grown on Earth, and microgravity-grown crystals had a slightly improved mosaicity (decreased by 0.03°) and diffraction resolution (decreased by 0.2 Å) compared with control crystals grown on Earth. However, the highest resolution and lowest mosaicity crystals were formed on Earth, and the highest-quality crystal overall was formed on Earth after return from microgravity. PMID:27710941

• Extracellular matrix protein in calcified endoskeleton: a potential additive for crystal growth and design

  NASA Astrophysics Data System (ADS)

  Azizur Rahman, M.; Fujimura, Hiroyuki; Shinjo, Ryuichi; Oomori, Tamotsu

  2011-06-01

  In this study, we demonstrate a key function of extracellular matrix proteins (ECMPs) on seed crystals, which are isolated from calcified endoskeletons of soft coral and contain only CaCO 3 without any living cells. This is the first report that an ECMP protein extracted from a marine organism could potentially influence in modifying the surface of a substrate for designing materials via crystallization. We previously studied with the ECMPs from a different type of soft coral ( Sinularia polydactyla) without introducing any seed crystals in the process , which showed different results. Thus, crystallization on the seed in the presence of ECMPs of present species is an important first step toward linking function to individual proteins from soft coral. For understanding this interesting phenomenon, in vitro crystallization was initiated in a supersaturated solution on seed particles of calcite (1 0 4) with and without ECMPs. No change in the crystal growth shape occurred without ECMPs present during the crystallization process. However, with ECMPs, the morphology and phase of the crystals in the crystallization process changed dramatically. Upon completion of crystallization with ECMPs, an attractive crystal morphology was found. Scanning electron microscopy (SEM) was utilized to observe the crystal morphologies on the seeds surface. The mineral phases of crystals nucleated by ECMPs on the seeds surface were examined by Raman spectroscopy. Although 50 mM Mg 2+ is influential in making aragonite in the crystallization process, the ECMPs significantly made calcite crystals even when 50 mM Mg 2+ was present in the process. Crystallization with the ECMP additive seems to be a technically attractive strategy to generate assembled micro crystals that could be used in crystals growth and design in the Pharmaceutical and biotechnology industries.

In situ study of the growth and degradation processes in tetragonal lysozyme crystals on a silicon substrate by high-resolution X-ray diffractometry

NASA Astrophysics Data System (ADS)

Kovalchuk, M. V.; Prosekov, P. A.; Marchenkova, M. A.; Blagov, A. E.; D'yakova, Yu. A.; Tereshchenko, E. Yu.; Pisarevskii, Yu. V.; Kondratev, O. A.

2014-09-01

The results of an in situ study of the growth of tetragonal lysozyme crystals by high-resolution X-ray diffractometry are considered. The crystals are grown by the sitting-drop method on crystalline silicon substrates of different types: both on smooth substrates and substrates with artificial surface-relief structures using graphoepitaxy. The crystals are grown in a special hermetically closed crystallization cell, which enables one to obtain images with an optical microscope and perform in situ X-ray diffraction studies in the course of crystal growth. Measurements for lysozyme crystals were carried out in different stages of the crystallization process, including crystal nucleation and growth, developed crystals, the degradation of the crystal structure, and complete destruction.

Thermal, mechanical, optical and dielectric properties of piperazinium hydrogen phosphite monohydrate NLO single crystal

NASA Astrophysics Data System (ADS)

Rajkumar, R.; Praveen Kumar, P.

2018-05-01

Optical transparent crystal of piperazinium hydrogen phosphite monohydrate (PHPM) was grown by slow evaporation method. The grown crystal was characterized by single crystal X-ray diffraction analysis and the crystal belongs to monoclinic system. The functional groups present in PHPM crystal were confirmed by FTIR analysis. UV-Visible spectrum shows that the PHPM crystal is transparent in the visible region. The mechanical behavior of PHPM crystal was characterized by Vickers hardness test. Thermal stability of PHPM crystal was analyzed by thermogravimetric analysis. Dielectric studies were also carried out for the grown crystal. The third-order nonlinear parameters such as nonlinear refractive index and nonlinear absorption coefficient have been calculated using Z scan technique.

Dynamically controlled crystallization method and apparatus and crystals obtained thereby

NASA Technical Reports Server (NTRS)

Arnowitz, Leonard (Inventor); Steinberg, Emanuel (Inventor)

1999-01-01

A method and apparatus for dynamically controlling the crystallization of proteins including a crystallization chamber or chambers for holding a protein in a salt solution, one or more salt solution chambers, two communication passages respectively coupling the crystallization chamber with each of the salt solution chambers, and transfer mechanisms configured to respectively transfer salt solution between each of the salt solution chambers and the crystallization chamber. The transfer mechanisms are interlocked to maintain the volume of salt solution in the crystallization chamber substantially constant. Salt solution of different concentrations is transferred into and out of the crystallization chamber to adjust the salt concentration in the crystallization chamber to achieve precise control of the crystallization process.

Crystal-to-Crystal Transition of Ultrasoft Colloids under Shear

NASA Astrophysics Data System (ADS)

Ruiz-Franco, J.; Marakis, J.; Gnan, N.; Kohlbrecher, J.; Gauthier, M.; Lettinga, M. P.; Vlassopoulos, D.; Zaccarelli, E.

2018-02-01

Ultrasoft colloids typically do not spontaneously crystallize, but rather vitrify, at high concentrations. Combining in situ rheo-small-angle-neutron-scattering experiments and numerical simulations we show that shear facilitates crystallization of colloidal star polymers in the vicinity of their glass transition. With increasing shear rate well beyond rheological yielding, a transition is found from an initial bcc-dominated structure to an fcc-dominated one. This crystal-to-crystal transition is not accompanied by intermediate melting but occurs via a sudden reorganization of the crystal structure. Our results provide a new avenue to tailor colloidal crystallization and the crystal-to-crystal transition at the molecular level by coupling softness and shear.

Can Solution Supersaturation Affect Protein Crystal Quality?

NASA Technical Reports Server (NTRS)

Gorti, Sridhar

2013-01-01

The formation of large protein crystals of "high quality" is considered a characteristic manifestation of microgravity. The physical processes that predict the formation of large, high quality protein crystals in the microgravity environment of space are considered rooted in the existence of a "depletion zone" in the vicinity of crystal. Namely, it is considered reasonable that crystal quality suffers in earth-grown crystals as a result of the incorporation of large aggregates, micro-crystals and/or large molecular weight "impurities", processes which are aided by density driven convective flow or mixing at the crystal-liquid interface. Sedimentation and density driven convection produce unfavorable solution conditions in the vicinity of the crystal surface, which promotes rapid crystal growth to the detriment of crystal size and quality. In this effort, we shall further present the hypothesis that the solution supersaturatoin at the crystal surface determines the growth mechanism, or mode, by which protein crystals grow. It is further hypothesized that protein crystal quality is affected by the mechanism or mode of crystal growth. Hence the formation of a depletion zone in microgravity environment is beneficial due to inhibition of impurity incorporatoin as well as preventing a kinetic roughening transition. It should be noted that for many proteins the magnitude of neither protein crystal growth rates nor solution supersaturation are predictors of a kinetic roughening transition. That is, the kinetic roughening transition supersaturation must be dtermined for each individual protein.

Metal-assisted and microwave accelerated-evaporative crystallization: Application to lysozyme protein

NASA Astrophysics Data System (ADS)

Mauge-Lewis, Kevin

In response to the growing need for new crystallization techniques that afford for rapid processing times along with control over crystal size and distribution, the Aslan Research Group has recently demonstrated the use of Metal-Assisted and Microwave-Accelerated Evaporative Crystallization MA-MAEC technique in conjunction with metal nanoparticles and nanostructures for the crystallization of amino acids and organic small molecules. In this study, we have employed the newly developed MA-MAEC technique to the accelerated crystallization of chicken egg-white lysozyme on circular crystallization platforms in order to demonstrate the proof-of-principle application of the method for protein crystallization. The circular crystallization platforms are constructed in-house from poly (methyl methacrylate) (PMMA) and silver nanoparticle films (SNFs), indium tin oxide (ITO) and iron nano-columns. In this study, we prove the MA-MAEC method to be a more effective technique in the rapid crystallization of macromolecules in comparison to other conventional methods. Furthermore, we demonstrate the use of the novel iCrystal system, which incorporates the use of continuous, low wattage heating to facilitate the rapid crystallization of the lysozyme while still retaining excellent crystal quality. With the incorporation of the iCrystal system, we observe crystallization times that are even shorter than those produced by the MA-MAEC technique using a conventional microwave oven in addition to significantly improved crystal quality.

Engineering calcium oxalate crystal formation in Arabidopsis

USDA-ARS?s Scientific Manuscript database

Many plants accumulate crystals of calcium oxalate. Just how these crystals form remains unknown. To gain insight into the mechanisms regulating calcium oxalate crystal formation, a crystal engineering approach was initiated utilizing the non-crystal accumulating plant, Arabidopsis. The success of t...

The Morse code effect: A crystal-crystal transformation observed in gel-grown lead (II) oxalate crystals

NASA Astrophysics Data System (ADS)

Lisgarten, J. N.; Marks, J. A.

2018-05-01

This paper reports on an unusual crystal-crystal transformation phenomenon, which we have called the Morse Code Effect, based on the change in appearance of lead(II) oxalate crystals grown in agarose gels.

Oxidative stability and lipid oxidation flavoring volatiles in antioxidants treated chicken meat patties during storage.

PubMed

Sohaib, Muhammad; Anjum, Faqir Muhammad; Arshad, Muhammad Sajid; Imran, Muhammad; Imran, Ali; Hussain, Shahzad

2017-02-01

Chicken meat contains higher percentage of polyunsaturated fatty acids that are susceptible to oxidative deterioration ultimately leading towards lower consumer acceptability for chicken meat products. Accordingly, meat processing industries are looking for combinations of natural antioxidants to enhance the oxidative stability and consumer acceptability of meat based products. The present study aimed to investigate the influence of directly added quercetin dihydrate in combination with α-tocopherol on oxidative stability, color characteristics, total carbonyls and flavor volatile compounds in chicken meat patties. Considering the preliminary studies, 3 levels of quercetin dihdrate @ 25, 50 and 100 mg/kg meat in combination with α-tocopherol at the rate 100 and 200 mg/kg meat were added to develop chicken meat patties and were stored at refrigeration temperature for 7 days. The oxidative stability of the antioxidant treated patties was determined by measuring malonaldehydes using TBARS and total carbonyls assay. The color (Lightness, redness and yellowness) of the patties was determined by using Konica Minolta Color Meter. Moreover, the volatile compounds were measured through gas chromatography at various storage intervals. The results elucidated that quercetin dehydrate inclusion at the rate of 50 mg/kg meat as well as particularly 100 mg/kg meat decreased the oxidation by reducing generation of malonaldehydes and total carbonyls in treated patties. Highest value for TBARS at initiation of storage was reported in (T 0 ) as 1.93 ± 0.02 whereas lowest were reported in T 6 and T 5 as 0.37 ± 0.01 and 0.38 ± 0.03 that were increased to 3.47 ± 0.14, 0.90 ± 0.05 and 0.94 ± 0.34 at the completion of storage. Moreover, the lowest carbonyls also reported in T6 and the values at various storage intervals (1st, 3rd and 7th) were as 0.59 ± 0.025, 0.77 ± 0.015 and 1.02 ± 0.031, respectively. The antioxidants inclusion also inhibited volatile flavoring compounds particularly aldehydes like hexanal and pentanal in a dose dependent manner (p ≤ 0.05). Lowest hexanal values reported in T 6 as 2488 ± 103 followed by T 4 (3701 ± 111) at the start of the trial whereas highest in T 0 (control) as 54,768 ± 431 that were increased to 9569 ± 607, 112,550 ± 897 and 359,826 ± 1285, correspondingly. The hexanal, as a critical indicator for the determination of volatiles in meat based products, was decreased with the addition of antioxidants and its highest values were reported in control group. Quercetin dihydrate addition along with alpha tocopherol is a pragmatic choice to improve oxidative storability and volatile flavor compounds in cooked meat patties. The data obtained will help meat processor to better develop antioxidant enriched formulations to augment oxidative stability and quality of processed meat products.

The Effect of Temperature and Solution pH on Tetragonal Lysozyme Nucleation Kinetics

NASA Technical Reports Server (NTRS)

Judge, Russell A.; Jacobs, Randolph S.; Frazier, Tyralynn; Snell, Edward H.; Pusey, Marc L.

1998-01-01

Part of the challenge of macromolecular crystal growth for structure determination is obtaining an appropriate number of crystals with a crystal volume suitable for x-ray analysis. In this respect an understanding of the effect of solution conditions on macromolecule nucleation rates is advantageous. This study investigated the effects of supersaturation, temperature and pH on the nucleation rate of tetragonal lysozyme crystals. Batch crystallization plates were prepared at given solution concentrations and incubated at set temperatures over one week. The number of crystals per well with their size and axial ratios were recorded and correlated with solution conditions, Duplicate experiments indicate the reproducibility of the technique, Crystal numbers were found to increase with increasing supersaturation and temperature. The most significant variable however, was pH, where crystal numbers changed by two orders of magnitude over the pH range 4.0 to 5.2. Crystal size varied also with solution conditions, with the largest crystals being obtained at pH 5.2. Having optimized the crystallization conditions, a batch of crystals were prepared under exactly the same conditions and fifty of these crystals were analyzed by x-ray techniques. The results indicate that even under the same crystallization conditions, a marked variation in crystal properties exists.

From screen to structure with a harvestable microfluidic device.

PubMed

Stojanoff, Vivian; Jakoncic, Jean; Oren, Deena A; Nagarajan, V; Poulsen, Jens-Christian Navarro; Adams-Cioaba, Melanie A; Bergfors, Terese; Sommer, Morten O A

2011-08-01

Advances in automation have facilitated the widespread adoption of high-throughput vapour-diffusion methods for initial crystallization screening. However, for many proteins, screening thousands of crystallization conditions fails to yield crystals of sufficient quality for structural characterization. Here, the rates of crystal identification for thaumatin, catalase and myoglobin using microfluidic Crystal Former devices and sitting-drop vapour-diffusion plates are compared. It is shown that the Crystal Former results in a greater number of identified initial crystallization conditions compared with vapour diffusion. Furthermore, crystals of thaumatin and lysozyme obtained in the Crystal Former were used directly for structure determination both in situ and upon harvesting and cryocooling. On the basis of these results, a crystallization strategy is proposed that uses multiple methods with distinct kinetic trajectories through the protein phase diagram to increase the output of crystallization pipelines.

Method for reducing energy losses in laser crystals

DOEpatents

Atherton, L.J.; DeYoreo, J.J.; Roberts, D.H.

1992-03-24

A process for reducing energy losses in crystals is disclosed which comprises: a. heating a crystal to a temperature sufficiently high as to cause dissolution of microscopic inclusions into the crystal, thereby converting said inclusions into point-defects, and b. maintaining said crystal at a given temperature for a period of time sufficient to cause said point-defects to diffuse out of said crystal. Also disclosed are crystals treated by the process, and lasers utilizing the crystals as a source of light. 12 figs.

Method for reducing energy losses in laser crystals

DOEpatents

Atherton, L. Jeffrey; DeYoreo, James J.; Roberts, David H.

1992-01-01

A process for reducing energy losses in crystals is disclosed which comprises: a. heating a crystal to a temperature sufficiently high as to cause dissolution of microscopic inclusions into the crystal, thereby converting said inclusions into point-defects, and b. maintaining said crystal at a given temperature for a period of time sufficient to cause said point-defects to diffuse out of said crystal. Also disclosed are crystals treated by the process, and lasers utilizing the crystals as a source of light.

Liquid encapsulated crystal growth

NASA Technical Reports Server (NTRS)

Morrison, Andrew D. (Inventor)

1989-01-01

Low-defect crystals are grown in a closed ampoule under a layer of encapsulant. After crystal growth, the crystal is separated from the melt and moved into the layer of encapsulant and cooled to a first temperature at which crystal growth stops. The crystal is then moved into the inert gas ambient in the ampoule and further cooled. The crystal can be separated from the melt by decanting the melt into an adjacent reservoir or by rotating the ampoule to rotate the crystal into the encapsulant layer.

Liquid encapsulated crystal growth

NASA Technical Reports Server (NTRS)

Morrison, Andrew D. (Inventor)

1987-01-01

Low-defect crystals are grown in a closed ampoule under a layer of encapsulant. After crystal growth, the crystal is separated from the melt and moved into the layer of encapsulant and cooled to a first temperature at which crystal growth stops. The crystal is then moved into the inert gas ambient in the ampoule and further cooled. The crystal can be separated from the melt by decanting the melt into and adjacent reservoir or by rotating the ampoule to rotate the crystal into the encapsulant layer.

A Few Good Crystals Please

NASA Technical Reports Server (NTRS)

Judge, Russell A.; Snell, Edward H.

1999-01-01

Part of the challenge of macromolecular crystal growth for structure determination is obtaining an appropriate number of crystals with a crystal volume suitable for X-ray analysis. In this respect an understanding of the effect of solution conditions on macromolecule nucleation rates is advantageous. This study investigated the effects of solution conditions on the nucleation rate and final crystal size of two crystal systems; tetragonal lysozyme and glucose isomerase. Batch crystallization plates were prepared at given solution concentration and incubated at set temperatures over one week. The number of crystals per well with their size and axial ratios were recorded and correlated with solution conditions. Duplicate experiments indicate the reproducibility of the technique. Results for each system showing the effect of supersaturation, incubation temperature and solution pH on nucleation rates will be presented and discussed. In the case of lysozyme, having optimized solution conditions to produce an appropriate number of crystals of a suitable size, a batch of crystals were prepared under exactly the same conditions. Fifty of these crystals were analyzed by x-ray techniques. The results indicate that even under the same crystallization conditions, a marked variation in crystal properties exists.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baba, Seiki; Hoshino, Takeshi; Ito, Len

A new crystal-mounting method has been developed that involves a combination of controlled humid air and polymer glue for crystal coating. This method is particularly useful when applied to fragile protein crystals that are known to be sensitive to subtle changes in their physicochemical environment. Protein crystals are fragile, and it is sometimes difficult to find conditions suitable for handling and cryocooling the crystals before conducting X-ray diffraction experiments. To overcome this issue, a protein crystal-mounting method has been developed that involves a water-soluble polymer and controlled humid air that can adjust the moisture content of a mounted crystal. Bymore » coating crystals with polymer glue and exposing them to controlled humid air, the crystals were stable at room temperature and were cryocooled under optimized humidity. Moreover, the glue-coated crystals reproducibly showed gradual transformations of their lattice constants in response to a change in humidity; thus, using this method, a series of isomorphous crystals can be prepared. This technique is valuable when working on fragile protein crystals, including membrane proteins, and will also be useful for multi-crystal data collection.« less

Simulation of the temperature distribution in crystals grown by Czochralski method

NASA Technical Reports Server (NTRS)

Dudokovic, M. P.; Ramachandran, P. A.

1985-01-01

Production of perfect crystals, free of residual strain and dislocations and with prescribed dopant concentration, by the Czochralski method is possible only if the complex, interacting phenomena that affect crystal growth in a Cz-puller are fully understood and quantified. Natural and forced convection in the melt, thermocapillary effect and heat transfer in and around the crystal affect its growth rate, the shape of the crystal-melt interface and the temperature gradients in the crystal. The heat transfer problem in the crystal and between the crystal and all other surfaces present in the crystal pulling apparatus are discussed at length. A simulation and computer algorithm are used, based on the following assumptions: (1) only conduction occurs in the crystal (experimentally determined conductivity as a function of temperature is used), (2) melt temperature and the melt-crystal heat transfer coefficient are available (either as constant values or functions of radial position), (3) pseudo-steady state is achieved with respect to temperature gradients, (4) crystal radius is fixed, and (5) both direct and reflected radiation exchange occurs among all surfaces at various temperatures in the crystal puller enclosure.

Self-powdering and nonlinear optical domain structures in ferroelastic β‧-Gd2(MoO4)3 crystals formed in glass

NASA Astrophysics Data System (ADS)

Tsukada, Y.; Honma, T.; Komatsu, T.

2009-08-01

Ferroelastic β'-Gd 2(MoO 4) 3, (GMO), crystals are formed through the crystallization of 21.25Gd 2O 3-63.75MoO 3-15B 2O 3 glass (mol%), and two scientific curious phenomena are observed. (1) GMO crystals formed in the crystallization break into small pieces with a triangular prism or pyramid shape having a length of 50-500 μm spontaneously during the crystallizations in the inside of an electric furnace, not during the cooling in air after the crystallization. This phenomenon is called "self-powdering phenomenon during crystallization" in this paper. (2) Each self-powdered GMO crystal grain shows a periodic domain structure with different refractive indices, and a spatially periodic second harmonic generation (SHG) depending on the domain structure is observed. It is proposed from polarized micro-Raman scattering spectra and the azimuthal dependence of second harmonic intensities that GMO crystals are oriented in each crystal grain and the orientation of (MoO 4) 2- tetrahedra in GMO crystals changes periodically due to spontaneous strains in ferroelastic GMO crystals.

Active crystals on a sphere

NASA Astrophysics Data System (ADS)

Praetorius, Simon; Voigt, Axel; Wittkowski, Raphael; Löwen, Hartmut

2018-05-01

Two-dimensional crystals on curved manifolds exhibit nontrivial defect structures. Here we consider "active crystals" on a sphere, which are composed of self-propelled colloidal particles. Our work is based on a phase-field-crystal-type model that involves a density and a polarization field on the sphere. Depending on the strength of the self-propulsion, three different types of crystals are found: a static crystal, a self-spinning "vortex-vortex" crystal containing two vortical poles of the local velocity, and a self-translating "source-sink" crystal with a source pole where crystallization occurs and a sink pole where the active crystal melts. These different crystalline states as well as their defects are studied theoretically here and can in principle be confirmed in experiments.