Novel application of thermally expanded graphite as the support of catalysts for direct synthesis of DMC from CH3OH and CO2.

PubMed

Bian, J; Xiao, M; Wang, S J; Lu, Y X; Meng, Y Z

2009-06-01

Novel Cu-Ni bimetallic catalysts supported on thermally expanded graphite (TEG) were prepared as an example to show the particular characteristics of TEG as a carbon support material. The structures of TEG and the synthesized Cu-Ni/TEG catalysts were characterized using BET, FTIR, TG, SEM, TEM, XRD and TPR techniques. The catalytic activities of the prepared catalysts were investigated by performing micro-reaction in the direct synthesis of dimethyl carbonate (DMC) from CH3OH and CO2. The experimental results indicated that the prepared Cu-Ni/TEG catalysts exhibited highly catalytic activity. Under the optimal catalytic conditions at 100 degrees C and under 1.2 MPa, the highest conversion of CH3OH of 4.97% and high selectivity of DMC of 89.3% can be achieved. The highly catalytic activity of Cu-Ni/TEG in DMC synthesis can be attributed to the synergetic effects of metal Cu, Ni and Cu-Ni alloy in the activation of CH3OH and CO2 and the particular characteristics of TEG as a carbon support material.

Competitive lithium solvation of linear and cyclic carbonates from quantum chemistry

DOE PAGES

Kent, Paul R. C.; Ganesh, Panchapakesan; Borodin, Oleg; ...

2015-11-17

The composition of the lithium cation (Li+) solvation shell in mixed linear and cyclic carbonate-based electrolytes has been re-examined using Born–Oppenheimer molecular dynamics (BOMD) as a function of salt concentration and cluster calculations with ethylene carbonate:dimethyl carbonate (EC:DMC)–LiPF 6 as a model system. A coordination preference for EC over DMC to a Li+ was found at low salt concentrations, while a slightly higher preference for DMC over EC was found at high salt concentrations. Analysis of the relative binding energies of the (EC) n(DMC) m–Li+ and (EC) n(DMC) m–LiPF 6 solvates in the gas-phase and for an implicit solvent (asmore » a function of the solvent dielectric constant) indicated that the DMC-containing Li+ solvates were stabilized relative to (EC 4)–Li+ and (EC) 3–LiPF 6 by immersing them in the implicit solvent. Such stabilization was more pronounced in the implicit solvents with a high dielectric constant. Results from previous Raman and IR experiments were reanalyzed and reconciled by correcting them for changes of the Raman activities, IR intensities and band shifts for the solvents which occur upon Li+ coordination. After these correction factors were applied to the results of BOMD simulations, the composition of the Li+ solvation shell from the BOMD simulations was found to agree well with the solvation numbers extracted from Raman experiments. Finally, the mechanism of the Li+ diffusion in the dilute (EC:DMC)LiPF 6 mixed solvent electrolyte was studied using the BOMD simulations.« less

Mechanistic investigations on dimethyl carbonate formation by oxidative carbonylation of methanol over a CuY zeolite: an operando SSITKA/DRIFTS/MS study.

PubMed

Engeldinger, Jana; Richter, Manfred; Bentrup, Ursula

2012-02-21

The simultaneous combination of steady state isotopic transient kinetic analysis (SSITKA) with diffuse reflectance Fourier transform spectroscopy (DRIFTS) and mass spectrometric (MS) analysis was applied to study the oxidative carbonylation of methanol (MeOH) to dimethyl carbonate (DMC) on a CuY zeolite catalyst prepared by incipient-wetness impregnation of commercial zeolite NH(4)-Y. The interaction of the catalyst with different reactants and reactant mixtures (O(2), CO, CO/O(2), MeOH/O(2), MeOH/CO, and MeOH/CO/O(2)) was studied in detail using (16)O(2)/(18)O(2) as well as (12)CO/(13)CO containing gas mixtures. DMC is produced via a monodentate monomethyl carbonate (MMC) species as intermediate which is formed by the concerted action of adsorbed methoxide and CO with gas phase MeOH. Adsorbed bidentate MMC species were found to be inactive. Lattice oxygen supplied by CuO(x) species is involved in the formation of MMC. Gas phase oxygen is needed to re-oxidize the catalyst but favours also the oxidation of CO to CO(2) and unselective oxidation reactions of MeOH to methyl formate, dimethoxymethane, and CO(2). The appropriate choice of reaction temperature and of the oxygen content in the reactant gas mixture was found to be indispensable for reaching high DMC selectivities.

Fabrication of Yolk-Shell Cu@C Nanocomposites as High-Performance Catalysts in Oxidative Carbonylation of Methanol to Dimethyl Carbonate

NASA Astrophysics Data System (ADS)

Wang, Juan; Hao, Panpan; Shi, Ruina; Yang, Leilei; Liu, Shusen; Zhao, Jinxian; Ren, Jun; Li, Zhong

2017-08-01

A facile way was developed to fabricate yolk-shell composites with tunable Cu cores encapsulated within hollow carbon spheres (Cu@C) with an average diameter about 210 nm and cavity size about 80 nm. During pyrolysis, the confined nanospace of hollow cavity ensures that the nucleation-and-growth process of Cu nanocrystals take place exclusively inside the cavities. The size of Cu cores can be easily tuned from 30 to 55 nm by varying the copper salt concentration. By deliberately creating shell porosity through KOH chemical activation, at an optimized KOH/HCS mass ratio of 1/4, the catalytic performance for the oxidative carbonylation of methanol to dimethyl carbonate (DMC) of the activated sample is enhanced remarkably with TOF up to 8.6 h-1 at methanol conversion of 17.1%. The activated yolk-shell catalyst shows promising catalytic properties involving the reusability with slight loss of catalytic activity and negligible leaching of activated components even after seven recycles, which is beneficial to the implementation of clean production for the eco-friendly chemical DMC thoroughly.

Performance Loss of Lithium Ion Polymer Batteries Subjected to Overcharge and Overdischarge Abuse

DTIC Science & Technology

2012-11-16

hexafluorophosphate EC: ethylene carbonate DEC: diethyl carbonate DMC: dimethyl carbonate PC: propylene carbonate     2    2. Introduction  Lithium -ion...Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/6110--12-9455 Performance Loss of Lithium Ion Polymer Batteries Subjected to Overcharge...ABSTRACT c. THIS PAGE 18. NUMBER OF PAGES 17. LIMITATION OF ABSTRACT Performance Loss of Lithium Ion Polymer Batteries Subjected to Overcharge and

Optimization of physicochemical characteristics of a lithium anode interface for high-efficiency cycling: an effect of electrolyte temperature

NASA Astrophysics Data System (ADS)

Ishikawa, Masashi; Tasaka, Yuko; Yoshimoto, Nobuko; Morita, Masayuki

Precycling of lithium (Li) metal on a nickel substrate at a low-temperature (-20°C) in propylene carbonate (PC) mixed with dimethyl carbonate (DMC) and Li hexafluorophosphate (LiPF 6) (LiPF 6-PC/DMC) enhanced Li cycleability in the subsequent cycles at a room temperature (25°C). In LiPF 6-PC/DMC, not only the low-temperature precycling in the initial 10 cycles was effective in the improvement of Li cycle life but also the first low-temperature Li deposition followed by room temperature cycling enhanced the Li cycle life. Such a precycling effect was observed with various current densities at the initial Li deposition and the subsequent cycling. When the current density of the cycling was high, improved cycling efficiency was observed and the efficiency of the Li electrode undergoing the precycling was close to that at a constant temperature of -20°C.

CuY zeolite catalysts prepared by ultrasonication-assisted ion-exchange for oxidative carbonylation of methanol to dimethyl carbonate.

PubMed

Woo, Je-Min; Seo, Jung Yoon; Kim, Hyunuk; Lee, Dong-Ho; Park, Young Cheol; Yi, Chang-Keun; Park, Yeong Seong; Moon, Jong-Ho

2018-06-01

The influence of ultrasonication treatment on the catalytic performance of CuY zeolite catalysts was investigated for the liquid-phase oxidative carbonylation of methanol to dimethyl carbonate (DMC). The deammoniation method of NH 4 Y into HY zeolites was optimized and characterized by elemental analyzer, derivative thermogravimetry, Brunauer-Emmett-Teller (BET) analyzer, and powder X-ray diffractometry, revealing that the HY zeolite deammoniated at 400 °C presented the highest surface area, complete ammonium/proton ion exchange, and no structure collapse, rendering it the best support from all the prepared zeolites. CuY zeolites were prepared via aqueous phase ion exchange with the aid of ultrasonication. Upon ultrasonication, the Cu + active centers were uniformly dispersed in the Y zeolites, penetrating the core of the zeolite particles in a very short time. In addition to enhancing the Cu dispersity, the ultrasonication treatment influenced the BET surface area, acid amount, Cu + /Cu 2+ ratio, and also had a relatively small impact on the Cu loading. Consequently, adequate exposure to ultrasonication was able to increase the conversion rate of methanol into dimethyl carbonate up to 11.4% with a comparable DMC selectivity of 23.7%. This methanol conversion is 2.65 times higher than that obtained without the ultrasonication treatment. Copyright © 2018 Elsevier B.V. All rights reserved.

Is 3-methyl-2-oxazolidinone a suitable solvent for lithium-ion batteries?

NASA Astrophysics Data System (ADS)

Gzara, L.; Chagnes, A.; Carré, B.; Dhahbi, M.; Lemordant, D.

3-Methyl-2-oxazolidinone (MeOx) has been mixed to ethylene carbonate (EC) or dimethyl carbonate (DMC) in presence of lithium tetrafluoroborate (LiBF 4) or lithium hexafluorophosphate (LiPF 6) for use as electrolyte in lithium batteries. The optimized electrolytes in term of conductivity and viscosity are MeOx:EC, x(MeOx) = 0.5 and MeOx:DMC, x(MeOx) = 0.4 in presence of LiBF 4 (1 M) or LiPF 6 (1 M). MeOx:EC electrolytes have a better thermal stability than MeOx:DMC electrolytes but the low wettability of the Celgard separator by MeOx:EC prevents its use in lithium batteries. No lithium insertion-deinsertion occurs when LiPF 6 is used as salt in MeOx-based electrolytes. MeOx:DMC, x(MeOx) = 0.4 + LiBF 4 (1 M) exhibits a good cycling ability at a graphite electrode but all the investigated electrolytes containing MeOx have a low stability in oxidation at a lithium cobalt oxide electrode (Li xCoO 2).

The local environment of Cu+ in Cu-Y zeolite and its relationship to the synthesis of dimethyl carbonate.

PubMed

Drake, Ian J; Zhang, Yihua; Briggs, Daniel; Lim, Bomyi; Chau, Tanguy; Bell, Alexis T

2006-06-22

Cu-exchanged Y zeolite was investigated in order to determine the location of the copper cations relative to the zeolite framework and to determine which Cu cations are active for the oxidative carbonylation of methanol to dimethyl carbonate (DMC). Cu-Y zeolite was prepared by vapor-phase exchange of H-Y with CuCl. The oxidation state, local coordination, and bond distances of Al and Cu were determined using Al K-edge and Cu K-edge X-ray absorption spectroscopy (XAS). Complimentary information was obtained by H2 temperature-programmed reduction and by in-situ infrared spectroscopy. Cu-Y has a Cu/Al ratio of unity and very little occluded CuCl. The average Al-O and Al-Cu bond distances are 1.67 angstroms and 2.79 angstroms, respectively, and the average Cu-O and Cu-Si(Al) bond distances are 1.99 angstroms and 3.13 angstroms, respectively. All of the Cu exchanged is present as Cu+ in sites I', II, and III'. Cu-Y is active for the oxidative carbonylation of methanol, and at low reactant contact time produces DMC as the primary product. With increasing reactant contact time, DMC formation decreases in preference to the formation of dimethoxy methane (DMM) and methylformate (MF). The formation of DMM and MF is attributed to the hydrogenation of DMC and the hydrogenolysis of DMM, respectively. Observation of the catalyst under reaction conditions reveals that most of the copper cations remain as Cu+, but some oxidation of Cu+ to Cu2+ does occur. It is also concluded that only those copper cations present in site II and III' positions are accessible to the reactants, and hence are catalytically active. The dominant adsorbed species on the surface are methoxy groups, and adsorbed CO is present as a minority species. The relationship of these observations to the kinetics of DMC synthesis is discussed.

Novel choline-based ionic liquids as safe electrolytes for high-voltage lithium-ion batteries

NASA Astrophysics Data System (ADS)

Yong, Tianqiao; Zhang, Lingzhi; Wang, Jinglun; Mai, Yongjin; Yan, Xiaodan; Zhao, Xinyue

2016-10-01

Three choline-based ionic liquids functionalized with trimethylsilyl, allyl, and cynoethyl groups are synthesized in an inexpensive route as safe electrolytes for high-voltage lithium-ion batteries. The thermal stabilities, viscosities, conductivities, and electrochemical windows of these ILs are reported. Hybrid electrolytes were formulated by doping with 0.6 M LiPF6/0.4 M lithium oxalydifluoroborate (LiODFB) as salts and dimethyl carbonate (DMC) as co-solvent. By using 0.6 M LiPF6/0.4 M LiODFB trimethylsilylated choline-based IL (SN1IL-TFSI)/DMC as electrolyte, LiCoO2/graphite full cell showed excellent cycling performance with a capacity of 152 mAh g-1 and 99% capacity retention over 90 cycles at a cut-off voltage of 4.4 V. The propagation rate of SN1IL-TFSI)/DMC electrolyte is only one quarter of the commercial electrolyte (1 M LiPF6 EC/DEC/DMC, v/v/v = 1/1/1), suggesting a better safety feature.

Highly efficient extraction and lipase-catalyzed transesterification of triglycerides from Chlorella sp. KR-1 for production of biodiesel.

PubMed

Lee, Ok Kyung; Kim, Young Hyun; Na, Jeong-Geol; Oh, You-Kwan; Lee, Eun Yeol

2013-11-01

We developed a method for the highly efficient lipid extraction and lipase-catalyzed transesterification of triglyceride from Chlorella sp. KR-1 using dimethyl carbonate (DMC). Almost all of the total lipids, approximately 38.9% (w/w) of microalgae dry weight, were extracted from the dried microalgae biomass using a DMC and methanol mixture (7:3 (v/v)). The extracted triglycerides were transesterified into fatty acid methyl esters (FAMEs) using Novozyme 435 as the biocatalyst in DMC. Herein, DMC was used as the reaction medium and acyl acceptor. The reaction conditions were optimized and the FAMEs yield was 293.82 mg FAMEs/g biomass in 6 h of reaction time at 60 °C in the presence of 0.2% (v/v) water. Novozyme 435 was reused more than ten times while maintaining relative FAMEs conversion that was greater than 90% of the initial FAMEs conversion. Copyright © 2013 Elsevier Ltd. All rights reserved.

Low-EC-Content Electrolytes for Low-Temperature Li-Ion Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall; Bugga, Ratnakumar; Surampudi, Subbarao

2003-01-01

Electrolytes comprising LiPF6 dissolved at a concentration of 1.0 M in three different mixtures of alkyl carbonates have been found well suited for use in rechargeable lithium-ion electrochemical cells at low temperatures. These and other electrolytes have been investigated in continuing research directed toward extending the lower limit of practical operating temperatures of Li-ion cells down to -60 C. This research at earlier stages was reported in numerous previous NASA Tech Briefs articles, the three most recent being "Ethyl Methyl Carbonate as a Cosolvent for Lithium-Ion Cells" (NPO-20605), Vol. 25, Low-EC-Content Electrolytes for Low-Temperature Li-Ion Cells No. 6 (June 2001), page 53; "Alkyl Pyrocarbonate Electrolyte Additives for Li-Ion Cells" (NPO-20775), Vol. 26, No. 5 (May 2002), page 37; and "Fluorinated Alkyl Carbonates as Cosolvents in Li-Ion Cells (NPO-21076), Vol. 26, No. 5 (May 2002), page 38. The present solvent mixtures, in terms of volume proportions of their ingredients, are 1 ethylene carbonate (EC) + 1 diethyl carbonate (DEC) + 1 dimethyl carbonate (DMC) + 3 ethyl methyl carbonate (EMC); 3EC + 3DMC + 14EMC; and 1EC + 1DEC + 1DMC + 4EMC. Relative to similar mixtures reported previously, the present mixtures, which contain smaller proportions of EC, have been found to afford better performance in experimental Li-ion cells at temperatures < -20 C.

[Study on three kinds of gasoline oxygenates-induced DNA damage in mice fibroblasts].

PubMed

Song, Chonglin; Zhang, Zhifu; Chen, Xue; Zhang, Yanfeng; Wang, Chunhua; Liu, Keming

2002-10-01

To study DNA damage of three kinds of gasoline oxygenates. Single cell gel electrophoresis assay(Comet assay) was used to detect the damage effects of three gasoline oxygenates[methyl tertiary butyl ether(MTBE), ethanol anhydrous(EA) and dimethyl carbonate(DMC)] on DNA in L-929 mice fibroblasts. In certain concentation(37.500-150.000 mg/ml), MTBE could directly cause DNA damage of L-929 mice fibroblasts. There was obvious dose-effect relationship, i.e. when the concentration of MTBE was increased from 9.375 to 150.000 mg/ml, the comet rate also increased from 4% to 85%, and the length of comet tail changed correspondingly. The results of EA and DMC were negative. Under the condition of this experiment(150.000 mg/ml), MTBE could directly cause DNA damage while the effect of EA and DMC on DNA damage was not found.

Carbon Materials Embedded with Metal Nanoparticles as Anode in Lithium-Ion Batteries

NASA Technical Reports Server (NTRS)

Hung, Ching-cheh

2002-01-01

Carbon materials containing metal nanoparticles that can form an alloy with lithium were tested for their capacity and cycle life to store and release lithium electrochemically. Metal nanoparticles may provide the additional lithium storage capacity as well as additional channels to conduct lithium in carbon. The cycle life of this carbon-metal composite can be long because the solid-electrolyte interface (SEI) on the carbon surface may protect both lithium and the metal particles in the carbon interior. In addition, the voids in the carbon interior may accommodate the nanoparticle's volume change, and such volume change may not cause much internal stress due to small sizes of the nanoparticles. This concept of improving carbon's performance to store and release lithium was demonstrated using experimental cells of C(Pd)/0.5M Lil-50/50 (vol.%) EC and DMC/Li, where C(Pd) was graphitized carbon fibers containing palladium nanoparticles, EC was ethylene carbonate, and DMC was dimethyl carbonate. However, such improvement was not observed if the Pd nanoparticles are replaced by aluminum, possibly because the aluminum nanoparticles were oxidized in air during storage, resulting in an inert oxide of aluminum. Further studies are needed to use this concept for practical applications.

High voltage stable liquid electrolytes for Li 1+ xMn 2O 4/carbon rocking-chair lithium batteries

NASA Astrophysics Data System (ADS)

Guyomard, D.; Tarascon, J. M.

A high voltage oxidation-resistant electrolyte is required for Li 1+ xMn 2O 4/carbon rocking-chair cells that need to be charged up to a voltage higher than 4.3 V. Many electrolyte compositions have been tested for their ability to resist to high voltages on Li 1+ xMn 2O 4 electrodes and their ability to maintain high ionic conductivity in a wide temperature range. This survey allowed us to select new electrolyte compositions in the system dimethyl carbonate (DMC) + ethylene carbonate (EC) + lithium hexafluorophosphate (LiPF 6) that are kinetically stable up to almost 5 V versus lithium at 55 °C on Li 1+ xMn 2O 4 electrodes. Low rate potentiostatic experiments, coupled with coulombmetric measurements in the 4.25-5.1 V range, allowed to select the following compositions: (DMC + EC) (1:2) + 1 M LiPF 6 and (DMC + EC) (2:1) + 1.5 M LiPF 6 as the best. These compositions have been used in practical Li 1+ xMn 2O 4/carbon rocking-chair batteries and show better performance in terms of cycle life and self-discharge over a wider temperature range. They are compatible with rocking-chair batteries based on LiCoO 2 and LiNiO 2 as well.

Supercapacitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Donghai; Yi, Ran; Chen, Shuru

Embodiments provide a hybrid supercapacitor exhibiting high energy and power densities enabled by a high-performance lithium-alloy anode coupled with a porous carbon cathode in an electrolyte containing lithium salt. Embodiments include a size reduced silicon oxide anode, a boron-doped silicon oxide anode, and/or a carbon coated silicon oxide anode, which may improve cycling stability and rate performance. Further embodiments include a hybrid supercapacitor system using a Li-active anode in an electrolyte including LiPF6 in a mixture of ethylene carbonate, diethyl carbonate, and dimethyl carbonate (EC:DEC:DMC, 2:1:2 by vol.) and 10 wt % fluoroethylene carbonate (FEC), which may reduce the self-dischargemore » rate.« less

Functional interface of polymer modified graphite anode

NASA Astrophysics Data System (ADS)

Komaba, S.; Ozeki, T.; Okushi, K.

Graphite electrodes were modified by polyacrylic acid (PAA), polymethacrylic acid (PMA), and polyvinyl alcohol (PVA). Their electrochemical properties were examined in 1 mol dm -3 LiClO 4 ethylene carbonate:dimethyl carbonate (EC:DMC) and propylene carbonate (PC) solutions as an anode of lithium ion batteries. Generally, lithium ions hardly intercalate into graphite in the PC electrolyte due to a decomposition of the PC electrolyte at ca. 0.8 V vs. Li/Li +, and it results in the exfoliation of the graphene layers. However, the modified graphite electrodes with PAA, PMA, and PVA demonstrated the stable charge-discharge performance due to the reversible lithium intercalation not only in the EC:DMC but also in the PC electrolytes since the electrolyte decomposition and co-intercalation of solvent were successfully suppressed by the polymer modification. It is thought that these improvements were attributed to the interfacial function of the polymer layer on the graphite which interacted with the solvated lithium ions at the electrode interface.

From CO2 to dimethyl carbonate with dialkyldimethoxystannanes: the key role of monomeric species.

PubMed

Kalhor, Mahboubeh Poor; Chermette, Henry; Chambrey, Stéphane; Ballivet-Tkatchenko, Danielle

2011-02-14

The formation of dimethyl carbonate (DMC) from CO(2) and methanol with the dimer [n-Bu(2)Sn(OCH(3))(2)](2) was investigated by experimental kinetics in support of DFT calculations. Under the reaction conditions (357-423 K, 10-20 MPa), identical initial rates are observed with three different reacting mixtures, CO(2)/toluene, supercritical CO(2), and CO(2)/methanol, and are consistent with the formation of monomeric di-n-butyltin(iv) species. An intramolecular mechanism is, therefore, proposed with an Arrhenius activation energy amounting to 104 ± 10 kJ mol(-1) for DMC synthesis. DFT calculations on the [(CH(3))(2)Sn(OCH(3))(2)](2)/CO(2) system show that the exothermic insertion of CO(2) into the Sn-OCH(3) bond occurs by a concerted Lewis acid-base interaction involving the tin center and the oxygen atom of the methoxy ligand. The Gibbs energy diagrams highlight that, under the reaction conditions, the dimer-monomer equilibrium is significantly shifted towards monomeric species, in agreement with the experimental kinetics. Importantly, the two Sn-OCH(3) bonds are prompt to insert CO(2). These results provide new insight into the reaction mechanism and catalyst design to enhance the turnover numbers.

A low-temperature electrolyte for lithium and lithium-ion batteries

NASA Astrophysics Data System (ADS)

Plichta, E. J.; Behl, W. K.

An electrolyte consisting of 1 M solution of lithium hexafluorophosphate in 1:1:1 ethylene carbonate(EC)-dimethyl carbonate(DMC)-ethyl methyl carbonate(EMC) is proposed for low temperature applications of lithium and lithium-ion cells. The new electrolyte has good conductivity and electrochemical stability. Lithium and lithium-ion cells using the new electrolyte were found to be operable at temperatures down to -40°C. The paper also reports on the electrochemical stability of aluminum metal, which is used as a substrate for the positive electrodes in lithium-ion cells, in the new electrolyte.

Control of lithium metal anode cycleability by electrolyte temperature

NASA Astrophysics Data System (ADS)

Ishikawa, Masashi; Kanemoto, Manabu; Morita, Masayuki

Precycling of lithium (Li) metal on a nickel substrate at low temperatures (0 and -20°C) in propylene carbonate (PC) mixed with dimethyl carbonate (DMC) and Li hexafluorophosphate (LiPF 6) (LiPF 6-PC/DMC) was found to enhance Li cycleability in the subsequent cycles at a room temperature (25°C). In contrast when the precycling at the low temperatures was performed in PC mixed with 2-methyltetrahydrofuran (2MeTHF) and LiPF 6 (LiPF 6-PC/2MeTHF), no improvement in the Li cycling efficiency was observed in the subsequent cycles at 25°C. These results suggest that the low-temperature precycling effect on the Li cycleability depends on a co-solvent used in the PC-based electrolytes. Ac impedance analysis revealed that the precycling in the low-temperature LiPF 6-PC/DMC electrolyte provided a compact Li interface with a low resistance. In marked constant to this, a Li anode interface formed by the precycling in the LiPF 6-PC/2MeTHF system was irregular and resistive to Li-ion diffusion. The origins of the low-temperature precycling effect dependent on the co-solvents were discussed.

Development of many-body polarizable force fields for Li-battery applications: 2. LiTFSI-doped Oligoether, polyether, and carbonate-based electrolytes.

PubMed

Borodin, Oleg; Smith, Grant D

2006-03-30

A quantum chemistry study of Li(+) interactions with ethers, carbonates, alkanes, and a trifluoromethanesulfonylimide anion (TFSI(-)) was performed at the MP2, B3LYP, and HF levels using the aug-cc-pvDz basis set for solvents and TFSI(-) anion, and [8s4p3d/5s3p2d]-type basis set for Li. A classical many-polarizable force field was developed for the LiTFSI salt interacting with ethylene carbonate (EC), gamma-butyrolactone (GBL), dimethyl carbonate (DMC), acetone, oligoethers, n-alkanes, and perfluoroalkanes. Molecular dynamics (MD) simulations were performed for EC/LiTFSI, PC/LiTFSI, GBL/LiTFSI, DMC/LiTFSI, 1,2-dimethoxyethane/LiTFSI, pentaglyme/LiTFSI, and poly(ethylene oxide) (MW = 2380)/LiTFSI electrolytes at temperatures from 298 to 423 K and salt concentrations from 0.3 to 5 M. The ion and solvent self-diffusion coefficients, electrolyte conductivity, electrolyte density, LiTFSI apparent molar volumes, and structure of the Li(+) cation environment predicted by MD simulations were found in good agreement with experimental data.

Lipase-catalyzed in-situ biosynthesis of glycerol-free biodiesel from heterotrophic microalgae, Aurantiochytrium sp. KRS101 biomass.

PubMed

Kim, Keon Hee; Lee, Ok Kyung; Kim, Chul Ho; Seo, Jeong-Woo; Oh, Baek-Rock; Lee, Eun Yeol

2016-07-01

Heterotrophic microalgae, Aurantiochytrium sp. KRS101 had a large amount of lipid (56.8% total lipids). The cells in the culture medium were easily ruptured due to thin cell wall of Aurantiochytrium sp., which facilitated in-situ fatty acid methyl esters (FAMEs) production directly from biomass. The harvested biomass had a high content of free fatty acids (FFAs), which was advantageous for glycerol-free FAMEs production. FAMEs were directly produced from Aurantiochytrium sp. KRS101 biomass (48.4% saponifiable lipids) using Novozyme 435-catalyzed in-situ esterification in dimethyl carbonate (DMC). DMC was used as a lipid extraction reagent, acyl acceptor and reaction medium. A 433.09mg FAMEs/g biomass was obtained with 89.5% conversion under the optimal condition: DMC to biomass ratio of 5:1 (v/w) and enzyme to biomass ratio of 30% (w/w) at 50°C for 12h. Glycerol could not be detected in the produced FAMEs. Copyright © 2016 Elsevier Ltd. All rights reserved.

In-situ pyrogenic production of biodiesel from swine fat.

PubMed

Lee, Jechan; Tsang, Yiu Fai; Jung, Jong-Min; Oh, Jeong-Ik; Kim, Hyung-Wook; Kwon, Eilhann E

2016-11-01

In-situ production of fatty acid methyl esters from swine fat via thermally induced pseudo-catalytic transesterification on silica was investigated in this study. Instead of methanol, dimethyl carbonate (DMC) was used as acyl acceptor to achieve environmental benefits and economic viability. Thermo-gravimetric analysis of swine fat reveals that swine fat contains 19.57wt.% of water and impurities. Moreover, the fatty acid profiles obtained under various conditions (extracted swine oil+methanol+NaOH, extracted swine oil+DMC+pseudo-catalytic, and swine fat+DMC+pseudo-catalytic) were compared. These profiles were identical, showing that the introduced in-situ transesterification is technically feasible. This also suggests that in-situ pseudo-catalytic transesterification has a high tolerance against impurities. This study also shows that FAME yield via in-situ pseudo-catalytic transesterification of swine fat reached up to 97.2% at 380°C. Therefore, in-situ pseudo-catalytic transesterification can be applicable to biodiesel production of other oil-bearing biomass feedstocks. Copyright © 2016 Elsevier Ltd. All rights reserved.

Methylation of Brazilein on Secang (Caesalpinia sappan Linn) Wood Extract for Maintain Color Stability to the Changes of pH

NASA Astrophysics Data System (ADS)

Ulma, Zeni; Rahayuningsih, Edia; Dwi Wahyuningsih, Tutik

2018-01-01

The stability of natural dyes to the changes of pH is really necessary when the natural dyes are applied either on fabric or food. This research aimed to increase the stability of brazilein, a compound contained within the secang wood extract, to the changes of pH. The methylation process was done by reacting Dimethyl Carbonate (DMC) with the brazilein on the secang wood extract. DMC acts as a substance that substitute hydroxyl group on brazilein. The methylation reaction of brazilein on secang wood extract was operated on a three-necked round-bottomed flask fitted with mercury-sealed stirrer and reflux condenser under 80°C temperature and 250 rpm stirring speed. There were two variables observed in this research; the DMC amount ratio to the amount of secang wood extract and the time of the methylation process. The research showed that at the 1:10 the DMC amount ratio to the amount of wood extract and 8 hours of the methylation process give the better stability of color of the secang wood extract than the variation of the other variables.

Modified silicas with different structure of grafted methylphenylsiloxane layer

NASA Astrophysics Data System (ADS)

Bolbukh, Yuliia; Terpiłowski, Konrad; Kozakevych, Roman; Sternik, Dariusz; Deryło-Marczewska, Anna; Tertykh, Valentin

2016-06-01

The method of a chemical assembly of the surface polymeric layer with high contents of the modifying agent was developed. Powders of nanodispersed silica with chemisorbed polymethylphenylsiloxane (PMPS) were synthesized by solvent-free chemical assembly technique with a dimethyl carbonate (DMC) as scission agent. Samples were characterized using FTIR spectroscopy, transmission electron microscopy (TEM), atomic force microscopy (AFM), and elemental analysis (CHN analysis). Coating microstructure, morphology, and hydrophilic-hydrophobic properties of nanoparticles were estimated. The results indicate a significant effect of the PMPS/DMC ratio at each modification stage on hydrophobic properties of modified silicas. Modification with a similar composition of the PMPS/DMC mixture, even with different polymer amount at each stage, provides the worst hydrophobicity. Results suggest that the highest hydrophobicity (contact angle θ = 135°-140°) is achieved in the case when silica modified with the PMPS/DMC mixture using multistage approach that providing a formation of the monomolecular layer of polysiloxane at the first modification step. The characteristics of surface structure were interpreted in terms of density of polymer-silica bonds at the interfaces that, usually, are reduced for modified surfaces, in a coupling with conformation model that accented the shape of chains (arch- and console-like) adsorbed on solid surfaces.

Comprehensive Insights into the Reactivity of Electrolytes Based on Sodium Ions.

PubMed

Eshetu, Gebrekidan Gebresilassie; Grugeon, Sylvie; Kim, Huikyong; Jeong, Sangsik; Wu, Liming; Gachot, Gregory; Laruelle, Stephane; Armand, Michel; Passerini, Stefano

2016-03-08

We report a systematic investigation of Na-based electrolytes that comprise various NaX [X=hexafluorophosphate (PF6 ), perchlorate (ClO4 ), bis(trifluoromethanesulfonyl)imide (TFSI), fluorosulfonyl-(trifluoromethanesulfonyl)imide (FTFSI), and bis(fluorosulfonyl)imide (FSI)] salts and solvent mixtures [ethylene carbonate (EC)/dimethyl carbonate (DMC), EC/diethyl carbonate (DEC), and EC/propylene carbonate (PC)] with respect to the Al current collector stability, formation of soluble degradation compounds, reactivity towards sodiated hard carbon (Nax -HC), and solid-electrolyte interphase (SEI) layer formation. Cyclic voltammetry demonstrates that the stability of Al is highly influenced by the nature of the anions, solvents, and additives. GC-MS analysis reveals that the formation of SEI telltales depends on the nature of the linear alkyl carbonates and the battery chemistry (Li(+) vs. Na(+) ). FTIR spectroscopy shows that double alkyl carbonates are the main components of the SEI layer on Nax -HC. In the presence of Na salts, EC/DMC and EC/DEC presented a higher reactivity towards Nax -HC than EC/PC. For a fixed solvent mixture, the onset temperature follows the sequence NaClO4

Spectroscopic Investigation of the Electrosynthesis of Diphenyl Carbonate from CO and Phenol on Gold Electrodes

PubMed Central

2018-01-01

In this work, we study the synthesis of diphenyl carbonate (DPC) from phenol and CO on gold electrodes studied by means of in situ Fourier transform infrared spectroscopy (FTIR). The results show that, on gold electrodes, the formation of DPC is observed at potentials as low as 0.4 V vs Ag/AgCl, together with the formation of dimethyl carbonate (DMC) from the carbonylation of methanol that was used as a solvent. The spectroelectrochemical results also suggest that the formation of DPC occurs via the replacement of the methoxy groups from DMC with phenoxy groups from phenol and not directly by the carbonylation of phenol. Although this transesterification process is known to occur with heterogeneous catalysts, it has not been reported under electrochemical conditions. These are interesting findings, since the direct DPC production by carbonylation of phenol to DPC is usually performed with Pd-based catalysts. With this reaction scheme of transesterification happening under electrochemical conditions, other non-Pd catalysts could be used as well for one-step DPC production from phenol and CO. These findings give important mechanistic insights into this reaction and open up possibilities to an alternative process for the production of DPC. PMID:29657886

Studies on the thermal breakdown of common Li-ion battery electrolyte components

DOE PAGES

Lamb, Joshua; Orendorff, Christopher J.; Roth, Emanuel Peter; ...

2015-08-06

While much attention is paid to the impact of the active materials on the catastrophic failure of lithium ion batteries, much of the severity of a battery failure is also governed by the electrolytes used, which are typically flammable themselves and can decompose during battery failure. The use of LiPF 6 salt can be problematic as well, not only catalyzing electrolyte decomposition, but also providing a mechanism for HF production. This work evaluates the safety performance of the common components ethylene carbonate (EC), diethyl carbonate (DEC), dimethyl carbonate (DMC), and ethyl methyl carbonate (EMC) in the context of the gassesmore » produced during thermal decomposition, looking at both the quantity and composition of the vapor produced. EC and DEC were found to be the largest contributors to gas production, both producing upwards of 1.5 moles of gas/mole of electrolyte. DMC was found to be relatively stable, producing very little gas regardless of the presence of LiPF 6. EMC was stable on its own, but the addition of LiPF 6 catalyzed decomposition of the solvent. As a result, while gas analysis did not show evidence of significant quantities of any acutely toxic materials, the gasses themselves all contained enough flammable components to potentially ignite in air.« less

Charge carrier dynamics in PMMA-LiClO4 based polymer electrolytes plasticized with different plasticizers

NASA Astrophysics Data System (ADS)

Pal, P.; Ghosh, A.

2017-07-01

We have studied the charge carrier dynamics in poly(methylmethacrylate)-LiClO4 polymer electrolytes plasticized with different plasticizers such as ethylene carbonate (EC), propylene carbonate (PC), polyethylene glycol (PEG), and dimethyl carbonate (DMC). We have measured the broadband complex conductivity spectra of these electrolytes in the frequency range of 0.01 Hz-3 GHz and in the temperature range of 203 K-363 K and analyzed the conductivity spectra in the framework of the random barrier model by taking into account the contribution of the electrode polarization observed at low frequencies and/or at high temperatures. It is observed that the temperature dependences of the ionic conductivity and relaxation time follow the Vogel-Tammann-Fulcher relation for all plasticized electrolytes. We have also performed the scaling of the conductivity spectra, which indicates that the charge carrier dynamics is almost independent of temperature and plasticizers in a limited frequency range. The existence of nearly constant loss in these electrolytes has been observed at low temperatures and/or high frequencies. We have studied the dielectric relaxation in these electrolytes using electric modulus formalism and obtained the stretched exponent and the decay function. We have observed less cooperative ion dynamics in electrolytes plasticized with DMC compared to electrolytes plasticized with EC, PC, and PEG.

Study on the decomposition mechanism of alkyl carbonate on lithium metal by pyrolysis-gas chromatography-mass spectroscopy

NASA Astrophysics Data System (ADS)

Mogi, Ryo; Inaba, Minoru; Iriyama, Yasutoshi; Abe, Takeshi; Ogumi, Zempachi

The surface films formed on deposited lithium in electrolyte solutions based on ethylene carbonate (EC), diethyl carbonate (DEC), and dimethyl carbonate (DMC) were analyzed by pyrolysis-gas chromatography-mass spectroscopy (Py-GC-MS). In 1 M LiClO 4/EC, the main component of the surface film was easily hydrolyzed to give ethylene glycol after exposure to air, and hence was considered to have a chemical structure of ROCH 2CH 2OR', of which OR and OR' are OLi or OCO 2Li. Ethylene oxide, acetaldehyde, and 1,4-dioxane were detected in decomposition products, and they were considered to have been formed by pyrolysis of ROCH 2CH 2OR' in the pyrolyzer. The presence of ethanol in decomposition products confirmed that ring cleavage at the CH 2O bonds of EC occurs by one electron reduction. In addition, the presence of methanol implied the cleavage of the CC bond of EC upon reduction. From the surface films formed in 1 M LiClO 4/DEC and /DMC, ethanol and methanol, respectively, were detected, which suggested that corresponding lithium alkoxides and/or lithium alkyl carbonates were the main components. In 1 M LiClO 4/EC+DEC (1:1), EC dominantly decomposed to form the surface film. The surface film formed in 1 M LiPF 6/EC+DEC (1:1) contained a much smaller amount of organic compounds.

Template-assisted formation of microsized nanocrystalline CeO2 tubes and their catalytic performance in the carboxylation of methanol

PubMed Central

Naumann, Meike; Schäfer, Christian; Brandner, Armin; Hofmann, Heiko J; Claus, Peter

2011-01-01

Summary Polymethylmethacrylate (PMMA)/ceria composite fibres were synthesized by using a sequential combination of polymer electrospinning, spray-coating with a sol, and a final calcination step to yield microstructured ceria tubes, which are composed of nanocrystalline ceria particles. The PMMA template is removed from the organic/inorganic hybrid material by radio frequency (rf) plasma etching followed by calcination of the ceramic green-body fibres. Microsized ceria (CeO2) tubes, with a diameter of ca. 0.75 µm, composed of nanocrystalline agglomerated ceria particles were thus obtained. The 1-D ceramic ceria material was characterized by X-ray diffraction, scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), UV–vis and photoluminescence spectroscopy (PL), as well as thermogravimetric analysis (TGA). Its catalytic performance was studied in the direct carboxylation of methanol with carbon dioxide leading to dimethyl carbonate [(CH3O)2CO, DMC], which is widely employed as a phosgene and dimethyl sulfate substitute, and as well as a fuel additive. PMID:22259761

Investigation of a novel ternary electrolyte based on dimethyl sulfite and lithium difluoromono(oxalato)borate for lithium ion batteries

NASA Astrophysics Data System (ADS)

Chen, Renjie; Zhu, Lu; Wu, Feng; Li, Li; Zhang, Rong; Chen, Shi

2014-01-01

Lithium difluoromono(oxalato)borate (LiODFB) has been used as a novel lithium salt for battery in recent studies. In this study, a series of novel electrolytes has been prepared by adding 30 vol% dimethyl sulfite (DMS) or dimethyl carbonate (DMC) as co-solvent into an ethylene carbonate (EC)/ethyl methyl carbonate (EMC) + LiX mixture, in which the LiX could be LiClO4, LiODFB, LiBOB, LiTFSI, or LiCF3SO3. These ternary electrolytes have been investigated for use in lithium ion batteries. FT-IR spectroscopy analysis shows that characteristic functional groups (-CO3, -SO3) undergo red-shift or blue-shift with the addition of different lithium salts. The LiODFB-EC/EMC/DMS electrolyte exhibits high ionic conductivity, which is mainly because of the low melting point of DMS, and LiODFB possessing high solubility. The Li/MCMB cells containing this novel electrolyte exhibit high capacities, good cycling performance, and excellent rate performance. These performances are probably because both LiODFB and DMS can assist in the formation of SEI films by reductive decomposition. Additionally, the discharge capacity of Li/LiCoO2 half cell containing LiODFB-EC/EMC/DMS electrolyte is 130.9 mAh g-1 after 50 cycles, and it is very comparable with the standard-commercial electrolyte. The results show that this study produces a promising electrolyte candidate for lithium ion batteries.

Electrolyte for high voltage Li/LiMn 1.9Co 0.1O 4 cells

NASA Astrophysics Data System (ADS)

Hayashi, Katsuya; Nemoto, Yasue; Tobishima, Shin-ichi; Yamaki, Jun-ichi

An electrolyte for high voltage lithium metal anode cells must simultaneously satisfy at least the following requirements; (i) high cycling efficiency on the lithium metal anode; (ii) higher oxidation potential than the charging voltage, and (iii) high specific conductivity. We have examined various electrolytes for lithium metal anode cells using a high voltage cathode, LiMn 1.9Co 0.1O 4. Of the electrolytes resistant to high voltage that we used, a system containing 60 to 90 vol.% of dimethyl carbonate (DMC) mixed with ethylene carbonate (EC) and 1.0 M lithium hexafluorophosphate (LiPF 6) provided the best cycling efficiency on a lithium metal anode, as well as a high specific conductivity around 10 mS cm -1 at 20 °C.

[Spectralsignatures of nickel and vanadium supported photocatalysts and their photocatalytic properties].

PubMed

Hai, Feng; Zhang, Qian-Cheng; Wang, Zhi-Wei; Jian, Li

2011-04-01

Using SiO2, activated carbon (AC) and Al2O3 as supports, the supported photocatalysts Ni-V-O/SiO2, Ni-V-O/AC and Ni-V-O/Al2O3 were prepared by impregnation method, and their spectralsignatures were investigated. The carbonylation of methanol with CO2 under UV irradiation was used as a probe reaction to compare the photocatalytic performance of the prepared catalysts. Integrated with the testing results of carbonylation, the effects of different supports on selectivity for the carbonylation products of methyl formate (MF) and dimethyl carbonate (DMC) were discussed by pyridine-IR and UV-Vis techniques. XRD results showed that the particles of nickel and vanadium supported on SiO2 had the highest degree of dispersion. Results of pyridine-IR indicated that all catalysts retained Lewis acid sites. The acid strength was different from catalyst samples with different supports but with the same active components. The acid strengths could be arranged as follows: Ni-V-O/SiO2 > Ni-V-O/Al2 O3 > Ni-V-O/AC. Different acid strengths exhibited different influence on the selectivity of products MF and DMC of carbonylation. The surface acid strengths of catalysts were the major factor influencing the selectivity of carbonylation products.

Polyfluorinated boron cluster based salts: A new electrolyte for application in nonaqueous asymmetric AC/Li 4Ti 5O 12 supercapacitors

NASA Astrophysics Data System (ADS)

Ionica-Bousquet, C. M.; Muñoz-Rojas, D.; Casteel, W. J.; Pearlstein, R. M.; Kumar, G. Girish; Pez, G. P.; Palacín, M. R.

Solutions of novel fluorinated lithium dodecaborate (Li 2B 12F xH 12- x) salts have been evaluated as electrolytes in nonaqueous asymmetric supercapacitors with Li 4Ti 5O 12 as negative electrode, and activated carbon (AC) as positive electrode. The results obtained with these new electrolytes were compared with those obtained with cells built using standard 1 M LiPF 6 dissolved in ethylene carbonate and dimethyl carbonate (EC:DMC; 1:1, v/v) as electrolyte. The specific energy, rate capability, and cycling performances of nonaqueous asymmetric cells based on these new electrolyte salts were studied. Cells assembled using the new fluoroborate salts show excellent reversibility, coulombic efficiency, rate capability and improved cyclability when compared with the standard electrolyte. These features confirm the suitability of lithium-fluoro-borate based salts to be used in nonaqueous asymmetric supercapacitors.

[Determination of twenty one elements in lithium hexafluorophosphate by ICP-AES].

PubMed

Fang, Yi-wen; Hao, Zhi-feng; Song, Yi-bing; Sun, Chang-yong; Yu, Jian; Yu, Lin

2005-02-01

One gram (+/- 0.0001 g) of lithium hexafluorophosphate was weighed exactly under dry atmosphere and was dissolved with an adequate amount of dimethyl carbonate (DMC). After the sample solution was pretreated with a series of methods, Be, Cu, Pb, Ca, Zr, Co, Mg, V, Ti, Mo, Ni, Mn, Sr, Zn, K, Al, Ba, Cd, Fe, Cr and Na were determined by ICP-AES. The results show that the recoveries of standard addition were 93.3%-102.1%, and the relative standard deviations (n = 11) were 0%-3.56%. The method is efficient, accurate and easy to operate. It has been applied to the determination of lithium hexafluorophosphate products with satisfactory results.

Thermal stability of LiPF 6 salt and Li-ion battery electrolytes containing LiPF 6

NASA Astrophysics Data System (ADS)

Yang, Hui; Zhuang, Guorong V.; Ross, Philip N.

The thermal stability of the neat lithium hexafluorophosphate (LiPF 6) salt and of 1 molal (m) solutions of LiPF 6 in prototypical Li-ion battery solvents was studied with thermogravimetric analysis (TGA) and on-line Fourier transform infrared (FTIR). Pure LiPF 6 salt is thermally stable up to 107 °C in a dry inert atmosphere, and its decomposition path is a simple dissociation producing lithium fluoride (LiF) as solid and PF 5 as gaseous products. In the presence of water (300 ppm) in the carrier gas, its decomposition onset temperature is lowered as a result of direct thermal reaction between LiPF 6 and water vapor to form phosphorous oxyfluoride (POF 3) and hydrofluoric acid (HF). No new products were observed in 1 m solutions of LiPF 6 in ethylene carbonate (EC), dimethyl carbonate (DMC) and ethyl methyl carbonate (EMC) by on-line TGA-FTIR analysis. The storage of the same solutions in sealed containers at 85 °C for 300-420 h did not produce any significant quantity of new products as well. In particular, no alkylflurophosphates were found in the solutions after storage at elevated temperature. In the absence of either an impurity like alcohol or cathode active material that may (or may not) act as a catalyst, there is no evidence of thermally induced reaction between LiPF 6 and the prototypical Li-ion battery solvents EC, PC, DMC or EMC.

From D-sorbitol to five-membered bis(cyclo-carbonate) as a platform molecule for the synthesis of different original biobased chemicals and polymers.

PubMed

Furtwengler, Pierre; Avérous, Luc

2018-06-14

Bis(cyclo-carbonate) was successfully synthesized from D-sorbitol (Sorb-BisCC) through an environmentally friendly process with dimethyl carbonate (DMC) as a reactant. In agreement with green chemistry principles, solvent free reactions were catalyzed and took place at low temperature. The reaction yield was increased until 50%, with the use of 1.3.5-triazabicyclo[4.4.0]dec-5-ene as catalyst and a continuous DMC feed to limit the side-reactions or the loss of reactant by azeotropic flux with a reactional subsidiary product. The obtained Sorb-BisCC is a remarkable platform molecule which could compete with others polycyclic platform molecules (isosorbide). Sorb-BisCC can be e.g., used to synthesize different chemicals such as short and long polyols, or novel biobased non-isocyanate polyurethanes (NIPU). Two Sorb-BisCC molecules have been coupled to obtain novel cyclic diols with pendant side chains. Polyether polyols were also obtained by anionic ring opening polymerization. According to the synthesis conditions, these synthetized polyether polyols range from partially to highly cross-linked materials. Finally, NIPU were synthesized with short and biobased fatty diamines. These different modifications and synthesis highlight the versatility of the Sorb-BisCC and demonstrated its high potential as building block. Sorb-BisCC can be considered as a platform molecule to open the way to different original and biobased chemical architectures.

Response surface method (RSM) for optimization of ionic conductivity of membranes polymer electrolyte poly (vinylidene fluoride) (PVDF) with polyvinyl pyrrolidone (PVP) as pore forming agent

NASA Astrophysics Data System (ADS)

Dyartanti, E. R.; Susanto, H.; Widiasa, I. N.; Purwanto, A.

2017-06-01

The Membranes Polymer Gel Electrolyte (MPGEs) based poly (vinylidene fluoride) (PVDF) was prepared by a phase inversion method using polyvinyl pyrrolidone (PVP) as a pore-forming agent and N, N-dimethyl acetamide (DMAc) as a solvent and water as non solvet. The membranes were then soaked in 1 M lithium hexafluorophosphate (LiPF6) in ethylene carbonate (EC) / dimethyl carbonate (DMC) / Diethyl carbonate (DEC) (4:2:4 %vol) solution in order to prepare polymer electrolyte membranes. The MPEGs PVDF/PVP/Nanoclay was applied using central composite design (CCD) experimental design to obtain a quantitative relationship between selected membranes prepared parameters namely (PVDF, PVP as pore forming agent and nanoclay filler concentration) and Ionic conductivity MPEGs. The model was used to find the optimum ionic conductivity from polymer electrolyte membranes. The polymer electrolyte membranes show good ionic conductivity on the order of 6.3 - 8.7 x 10-3 S cm-1 at the ambient temperatures. The ionic conductivity tended to increase with PVP and nanoclay concentration and decrease with PVDF composition. The model predicted the maximum ionic conductivity of 8.47 x 10-3 S cm-1 when the PVDF, PVP and nanoclay concentration were set at 8.01 %, 8.04 % and 10.12%, respectively. The first section in your paper.

Submicroporous/microporous and compatible/incompatible multi-functional dual-layer polymer electrolytes and their interfacial characteristics with lithium metal anode

NASA Astrophysics Data System (ADS)

Lee, Young-Gi; Kyhm, Kwangseuk; Choi, Nam-Soon; Ryu, Kwang Sun

A novel multi-functional dual-layer polymer electrolyte was prepared by impregnating the interconnected pores with an ethylene carbonate (EC)/dimethyl carbonate (DMC)/lithium hexafluorophosphate (LiPF 6) solution. An incompatible layer is based on a microporous polyethylene (PE) and a compatible layer, based on a poly(vinylidenefluoride-co-hexafluoropropylene) (P(VdF-co-HFP)) is sub-microporous and compatible with an electrolyte solution. The Li electrode/the dual-layer polymer electrolyte/Li[Ni 0.15Li 0.23M n0.62]O 2 cell showed stable cycle performance under prolonged cycle number. This behavior is due to the enhanced compatibility between the matrix polymer and the liquid electrolytes within the submicroporous compatible layer, which could lead to a controlled Li + deposition on the Li anode surface by forming homegeneous electrolyte zone near the anode.

Measurement of the through thickness compression of a battery separator

NASA Astrophysics Data System (ADS)

Yan, Shutian; Huang, Xiaosong; Xiao, Xinran

2018-04-01

The mechanical integrity of the separator is critical to the reliable operation of a battery. Due to its minimal thickness, compression experiments with a single/a few layers of separator are difficult to perform. In this work, a capacitance based displacement set-up has been developed for the measurement of the through thickness direction (TTD) compression stress-strain behavior of the separator and the investigation of its interaction with the electrode. The experiments were performed for a stack of two layers of Celgard 2400 separator, NMC cathode, and separator/NMC cathode/separator stack in both dry and wet (i.e. submersed in dimethyl carbonate DMC) conditions. The experimental results reveal that the separator compression modulus can be significantly affected by the presence of DMC. The iso-stress based rule of mixtures was used to compute the compressive stress-strain curve for the stack from that of the separator and NMC layer. The computed curve agreed with the experimental curve reasonably well up to about 0.16 strain but deviated significantly to a softer response at higher strains. The results suggest that, in the stack, the TTD compressive deformation of the separator is influenced by the NMC cathode.

Ultrasonic-microwave assisted synthesis of three-dimensional polyvinyl alcohol carbonate/graphene oxide sponge and studies of surface resistivity and thermal stability.

PubMed

Song, Yunna; Li, Yuehai; Li, Jihui; Li, Yongshen; Niu, Shuai; Li, Ning

2018-04-01

In the article, graphene oxide (GO) was prepared by flake graphite, nitric acid and peroxyacetic acid via the sonochemical method and characterized, and polyvinyl alcohol carbonate/GO composite (PVAC/GO composite) was synthesized by polyvinyl alcohol (PVA), dimethyl carbonate (DMC) and GO via the approach of transesterification in the case of ultrasonic-microwave synergistic effects and characterized, and three-dimensional PVAC/GO sponge (3D PVAC/GO sponge) was manufactured by PVAC/GO composite via the foaming approach and characterized, and the thermal stability and surface resistivity of 3D PVAC/GO sponge were investigated. Based on those, it had been attested that PVAC polymer was structured by DMC and PVA and had the six-membered lactone rings and the ether bonds, and PVAC/GO composite was constituted by 2D GO lattice and PVAC polymer, and 3D PVAC/GO sponge was constructed by PVAC/GO composite, and the surface resistivity of 3D PVAC/GO sponge with 0.00, 0.60, 1.20, 1.80 and 2.40 g of GO were 9.07  ×  10 7 , 6.02  ×  10 7 , 4.65  ×  10 7 , 2.47  ×  10 7 and 1.06  ×  107 O/sq, and the thermal stability of 3D PVAC/GO sponge had improved. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of Carbon Structure and Surface Oxygen on the Carbon's Performance as the Anode in Lithium-Ion Battery Determined

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh

2000-01-01

Four carbon materials (C1, C2, C3, and C4) were tested electrochemically at the NASA Glenn Research Center at Lewis Field to determine their performance in lithium-ion batteries. They were formed as shown in the figure. This process caused very little carbon loss. Products C1 and C3 contained very little oxygen because of the final overnight heating at 540 C. Products C2 and C4, on the other hand, contained small amounts of basic oxide. The electrochemical test involved cycles of lithium intercalation and deintercalation using C/saturated LiI-50/50 (vol %) ethylene carbonate (EC) and dimethyl carbonate (DMC)/Li half cell. The cycling test, which is summarized in the table, resulted in three major conclusions. The capacity of the carbon with a basic oxide surface converges to a constant 1. value quickly (within 4 cycles), possibly because the oxide prevents solvent from entering the carbon structure and, therefore, prolongs the carbon s cycle life. Under certain conditions, the disordered carbon can store more lithium than its 2. precursor. These samples and their precursor can intercalate at 200 mA/g and deintercalate at 3. a rate of 2000 mA/g without significant capacity loss.

Electrochemical properties of lithium iron phosphate cathode material using polymer electrolyte

NASA Astrophysics Data System (ADS)

Kim, Jae-Kwang; Choi, Jae-Won; Cheruvally, Gouri; Shin, Yong-Jo; Ahn, Jou-Hyeon; Cho, Kwon-Koo; Ahn, Hyo-Jun; Kim, Ki-Won

2007-12-01

Carbon-coated lithium iron phosphate (LiFePO4/C) cathode material was synthesized by mechano-chemical activation method. The performance of LiFePO4/C in lithium battery was tested with an electrospun polymer-based electrolyte. Liquid electrolyte of 1M lithium hexafluorophosphate (LiPF6) in ethylene carbonate/dimethyl carbonate (EC/DMC) (1 : 1vol) was incorporated in electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (P(VdF-HFP)) microfibrous membrane to prepare the polymer electrolyte (PE). The cell based on Li|PE|Li FePO4/C exhibited an initial discharge capacity of 142 mAh g-1 at 0.1 C-rate at room temperature. Good cycling performance even under the high current density of 2 C could be obtained. Impedance spectroscopy was applied to investigate the material behavior during 0.1 C-rate charge-discharge cycling. When the fresh cell and the cell after different cycles were compared, impedance resistance was found to decrease with cycling. Impedance study indicated good cycle life for the cell when tested at room temperature.

Solvent decompositions and physical properties of decomposition compounds in Li-ion battery electrolytes studied by DFT calculations and molecular dynamics simulations.

PubMed

Tasaki, Ken

2005-02-24

The density functional theory (DFT) calculations have been performed for the reduction decompositions of solvents widely used in Li-ion secondary battery electrolytes, ethylene carbonate (EC), propylene carbonate (PC), dimethyl carbonates (DMC), ethyl methyl carbonate (EMC), and diethyl carbonate (DEC), including a typical electrolyte additive, vinylene carbonate (VC), at the level of B3LYP/6-311+G(2d,p), both in the gas phase and solution using the polarizable conductor calculation model. In the gas phase, the first electron reduction for the cyclic carbonates and for the linear carbonates is found to be exothermic and endothermic, respectively, while the second electron reduction is endothermic for all the compounds examined. On the contrary, in solution both first and second electron reductions are exothermic for all the compounds. Among the solvents and the additive examined, the likelihood of undergoing the first electron reduction in solution was found in the order of EC > PC > VC > DMC > EMC > DEC with EC being the most likely reduced. VC, on the other hand, is most likely to undergo the second electron reduction among the compounds, in the order of VC > EC > PC. Based on the results, the experimentally demonstrated effectiveness of VC as an excellent electrolyte additive was discussed. The bulk thermodynamic properties of two dilithium alkylene glycol dicarbonates, dilithium ethylene glycol dicarbonate (Li-EDC) and dilithium 1,2-propylene glycol dicarbonate (Li-PDC), as the major component of solid-electrolyte interface (SEI) films were also examined through molecular dynamics (MD) simulations in order to understand the stability of the SEI film. It was found that film produced from a decomposition of EC, modeled by Li-EDC, has a higher density, more cohesive energy, and less solubility to the solvent than the film produced from decomposition of PC, Li-PDC. Further, MD simulations of the interface between the decomposition compound and graphite suggested that Li-EDC has more favorable interactions with the graphite surface than Li-PDC. The difference in the SEI film stability and the behavior of Li-ion battery cycling among the solvents were discussed in terms of the molecular structures.

Quasiparticle and excitonic gaps of one-dimensional carbon chains.

PubMed

Mostaani, E; Monserrat, B; Drummond, N D; Lambert, C J

2016-06-01

We report diffusion quantum Monte Carlo (DMC) calculations of the quasiparticle and excitonic gaps of hydrogen-terminated oligoynes and extended polyyne. The electronic gaps are found to be very sensitive to the atomic structure in these systems. We have therefore optimised the geometry of polyyne by directly minimising the DMC energy with respect to the lattice constant and the Peierls-induced carbon-carbon bond-length alternation. We find the bond-length alternation of polyyne to be 0.136(2) Å and the excitonic and quasiparticle gaps to be 3.30(7) and 3.4(1) eV, respectively. The DMC zone-centre longitudinal optical phonon frequency of polyyne is 2084(5) cm(-1), which is consistent with Raman spectroscopic measurements for large oligoynes.

Dimensional stability and electrochemical behaviour of ZrO2 incorporated electrospun PVdF-HFP based nanocomposite polymer membrane electrolyte for Li-ion capacitors

PubMed Central

Solarajan, Arun Kumar; Murugadoss, Vignesh; Angaiah, Subramania

2017-01-01

Different weight percentages of ZrO2 (0, 3, 5, 7 and 10 wt%) incorporated electrospun PVDF-HFP nanocomposite polymer membranes (esCPMs) were prepared by electrospinning technique. They were activated by soaking in 1 M LiPF6 containing 1:1 volume ratio of EC : DMC (ethylene carbonate:dimethyl carbonate) to get electrospun nanocomposite polymer membrane electrolytes (esCPMEs). The influence of ZrO2 on the physical, mechanical and electrochemical properties of esCPM was studied in detail. Finally, coin type Li-ion capacitor cell was assembled using LiCo0.2Mn1.8O4 as the cathode, Activated carbon as the anode and the esCPME containing 7 wt% of ZrO2 as the separator, which delivered a discharge capacitance of 182.5 Fg−1 at the current density of 1Ag−1 and retained 92% of its initial discharge capacitance even after 2,000 cycles. It revealed that the electrospun PVdF-HFP/ZrO2 based nanocomposite membrane electrolyte could be used as a good candidate for high performance Li-ion capacitors. PMID:28397783

Dimensional stability and electrochemical behaviour of ZrO2 incorporated electrospun PVdF-HFP based nanocomposite polymer membrane electrolyte for Li-ion capacitors.

PubMed

Solarajan, Arun Kumar; Murugadoss, Vignesh; Angaiah, Subramania

2017-04-11

Different weight percentages of ZrO 2 (0, 3, 5, 7 and 10 wt%) incorporated electrospun PVDF-HFP nanocomposite polymer membranes (esCPMs) were prepared by electrospinning technique. They were activated by soaking in 1 M LiPF 6 containing 1:1 volume ratio of EC : DMC (ethylene carbonate:dimethyl carbonate) to get electrospun nanocomposite polymer membrane electrolytes (esCPMEs). The influence of ZrO 2 on the physical, mechanical and electrochemical properties of esCPM was studied in detail. Finally, coin type Li-ion capacitor cell was assembled using LiCo 0.2 Mn 1.8 O 4 as the cathode, Activated carbon as the anode and the esCPME containing 7 wt% of ZrO 2 as the separator, which delivered a discharge capacitance of 182.5 Fg -1 at the current density of 1Ag -1 and retained 92% of its initial discharge capacitance even after 2,000 cycles. It revealed that the electrospun PVdF-HFP/ZrO 2 based nanocomposite membrane electrolyte could be used as a good candidate for high performance Li-ion capacitors.

Study on characteristics of PVDF/nano-clay composite polymer electrolyte using PVP as pore-forming agent

NASA Astrophysics Data System (ADS)

Dyartanti, Endah R.; Purwanto, Agus; Widiasa, I. Nyoman; Susanto, Heru

2016-02-01

Polyvinylidene fluoride (PVDF) based polymer electrolytes have a high dielectric constant, which can assist in greater ionization of lithium salts. The main advantages of PVDF are its durability in long battery operation and its ability to be a good ion conductor. However, the limitation of this polymer is its crystalline molecular structure. Dispersing nano-particles in the polymer matrix may improve the characteristics of the PVDF polymer. This paper aims to investigate the impact of nano-clay addition on the characteristics of PVDF polymer to be used as a polymer electrolyte membrane. In addition, the effect of poly(vinyl pyrrolidone) (PVP) is also investigated. The membrane was prepared by phase separation method whereas the polymer electrolyte membranes was prepared by immersing into 1 M lithium hexafluorophosphate (LiPF6) in ethylene carbonate/dimethyl carbonate (EC/DMC) electrolytes for 1 h. The membranes were characterized by scanning electron microscope (SEM), porosity and electrolyte uptake and performance in battery cell. The results showed that both nano-clay and PVP have significant impacts on the improvement of PVDF membranes to be used as polymer electrolyte.

Investigation of Ion-Solvent Interactions in Nonaqueous Electrolytes Using in Situ Liquid SIMS.

PubMed

Zhang, Yanyan; Su, Mao; Yu, Xiaofei; Zhou, Yufan; Wang, Jungang; Cao, Ruiguo; Xu, Wu; Wang, Chongmin; Baer, Donald R; Borodin, Oleg; Xu, Kang; Wang, Yanting; Wang, Xue-Lin; Xu, Zhijie; Wang, Fuyi; Zhu, Zihua

2018-03-06

Ion-solvent interactions in nonaqueous electrolytes are of fundamental interest and practical importance, yet debates regarding ion preferential solvation and coordination numbers persist. In this work, in situ liquid SIMS was used to examine ion-solvent interactions in three representative electrolytes, i.e., lithium hexafluorophosphate (LiPF 6 ) at 1.0 M in ethylene carbonate (EC)-dimethyl carbonate (DMC) and lithium bis(fluorosulfonyl)imide (LiFSI) at both low (1.0 M) and high (4.0 M) concentrations in 1,2-dimethoxyethane (DME). In the positive ion mode, solid molecular evidence strongly supports the preferential solvation of Li + by EC. Besides, from the negative spectra, we also found that PF 6 - forms association with EC, which has been neglected by previous studies due to the relatively weak interaction. In both LiFSI in DME electrolytes, however, no evidence shows that FSI - is associated with DME. Furthermore, strong salt ion cluster signals were observed in the 1.0 M LiPF 6 in EC-DMC electrolyte, suggesting that a significant amount of Li + ions stay in the vicinity of anions. In sharp comparison, weak ion cluster signals were detected in dilute LiFSI in DME electrolyte, suggesting most ions are well separated, in agreement with our molecular dynamics simulation results. These findings indicate that with virtues of little bias on detecting positive and negative ions and the capability of directly analyzing concentrated electrolytes, in situ liquid SIMS is a powerful tool that can provide key evidence for improved understanding on the ion-solvent interactions in nonaqueous electrolytes. Therefore, we anticipate wide applications of in situ liquid SIMS on investigations of various ion-solvent interactions in the near future.

Investigation of Ion-Solvent Interactions in Nonaqueous Electrolytes Using in Situ Liquid SIMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yanyan; Su, Mao; Yu, Xiaofei

2018-02-06

Ion-solvent interactions in non-aqueous electrolytes are of fundamental interest and practical importance, yet debates regarding ion preferential solvation and coordination numbers persist. In this work, in situ liquid SIMS was used to examine ion-solvent interactions in three representative electrolytes, i.e., lithium hexafluorophosphate (LiPF6) at 1.0 M in ethylene carbonate (EC)-dimethyl carbonate (DMC), and lithium bis(fluorosulfonyl)imide (LiFSI) at both low (1.0 M) and high (4.0 M) concentrations in 1,2-dimethoxyethane (DME). In the positive ion mode, solid molecular evidence strongly supports the preferential solvation of Li+ by EC. Besides, from the negative spectra, we also found that PF6- forms association with EC,more » which has been neglected by previous studies due to the relatively weak interaction. While in both LiFSI in DME electrolytes, no evidence shows that FSI- is associated with DME. Furthermore, strong salt ion cluster signals were observed in the 1.0 M LiPF6 in EC-DMC electrolyte, suggesting that a significant amount of Li+ ions stay in vicinity of anions. In sharp comparison, weak ion cluster signals were detected in dilute LiFSI in DME electrolyte, suggesting most ions are well separated, in agreement with our molecular dynamics (MD) simulation results. These findings indicate that with virtues of little bias on detecting positive and negative ions and the capability of directly analyzing concentrated electrolytes, in situ liquid SIMS is a powerful tool that can provide key evidence for improved understanding on the ion-solvent interactions in non-aqueous electrolytes. Therefore, we anticipate wide applications of in situ liquid SIMS on investigations of various ion-solvent interactions in the near future.« less

Investigation of Ion–Solvent Interactions in Nonaqueous Electrolytes Using in Situ Liquid SIMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Yanyan; Su, Mao; Yu, Xiaofei

Ion-solvent interactions in non-aqueous electrolytes are of fundamental interest and practical importance, yet debates regarding ion preferential solvation and coordination numbers persist. In this work, in situ liquid SIMS was used to examine ion-solvent interactions in three representative electrolytes, i.e., lithium hexafluorophosphate (LiPF6) at 1.0 M in ethylene carbonate (EC)-dimethyl carbonate (DMC), and lithium bis(fluorosulfonyl)imide (LiFSI) at both low (1.0 M) and high (4.0 M) concentrations in 1,2-dimethoxyethane (DME). In the positive ion mode, solid molecular evidence strongly supports the preferential solvation of Li+ by EC. Besides, from the negative spectra, we also found that PF6- forms association with EC,more » which has been neglected by previous studies due to the relatively weak interaction. While in both LiFSI in DME electrolytes, no evidence shows that FSI- is associated with DME. Furthermore, strong salt ion cluster signals were observed in the 1.0 M LiPF6 in EC-DMC electrolyte, suggesting that a significant amount of Li+ ions stay in vicinity of anions. In sharp comparison, weak ion cluster signals were detected in dilute LiFSI in DME electrolyte, suggesting most ions are well separated, in agreement with our molecular dynamics (MD) simulation results. These findings indicate that with virtues of little bias on detecting positive and negative ions and the capability of directly analyzing concentrated electrolytes, in situ liquid SIMS is a powerful tool that can provide key evidence for improved understanding on the ion-solvent interactions in non-aqueous electrolytes. Therefore, we anticipate wide applications of in situ liquid SIMS on investigations of various ion-solvent interactions in the near future.« less

Understanding transport mechanisms in ionic liquid/carbonate solvent electrolyte blends.

PubMed

Oldiges, K; Diddens, D; Ebrahiminia, M; Hooper, J B; Cekic-Laskovic, I; Heuer, A; Bedrov, D; Winter, M; Brunklaus, G

2018-06-20

To unravel mechanistic details of the ion transport in liquid electrolytes, blends of the ionic liquid (IL) 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (Pyr14TFSI), ethylene carbonate (EC) and dimethyl carbonate (DMC) with the conducting salts lithium hexafluorophosphate (LiPF6) and lithium bis(trifluoromethylsulfonyl)imide (LiTFSI) were investigated as a function of the IL concentration. Electrochemical impedance, Pulsed Field Gradient Nuclear Magnetic Resonance (PFG NMR) and Raman spectroscopy supported by Molecular Dynamics (MD) simulations allowed the structural and dynamic correlations of the ion motions to be probed. Remarkably, we identified that though the individual correlations among different ion types exhibit a clear concentration dependence, their net effect is nearly constant throughout the entire concentration range, resulting in approximately equal transport and transference numbers, despite a monitored cross-over from carbonate-based lithium coordination to a TFSI-based ion coordination. In addition, though dynamical ion correlation could be found, the absolute values of the ionic conductivity are essentially determined by the overall viscosity of the electrolyte. The IL/carbonate blends with a Pyr14TFSI fraction of ∼10 wt% are found to be promising electrolyte solvents, with ionic conductivities and lithium ion transference numbers comparable to those of standard carbonate-based electrolytes while the thermal and electrochemical stabilities are considerably improved. In contrast, the choice of the conducting salt only marginally affects the transport properties.

Study on characteristics of PVDF/nano-clay composite polymer electrolyte using PVP as pore-forming agent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyartanti, Endah R., E-mail: heru.susanto@undip.ac.id, E-mail: endah-rd@uns.ac.id; Department of Chemical Engineering, Diponegoro University, Semarang; Purwanto, Agus

2016-02-08

Polyvinylidene fluoride (PVDF) based polymer electrolytes have a high dielectric constant, which can assist in greater ionization of lithium salts. The main advantages of PVDF are its durability in long battery operation and its ability to be a good ion conductor. However, the limitation of this polymer is its crystalline molecular structure. Dispersing nano-particles in the polymer matrix may improve the characteristics of the PVDF polymer. This paper aims to investigate the impact of nano-clay addition on the characteristics of PVDF polymer to be used as a polymer electrolyte membrane. In addition, the effect of poly(vinyl pyrrolidone) (PVP) is alsomore » investigated. The membrane was prepared by phase separation method whereas the polymer electrolyte membranes was prepared by immersing into 1 M lithium hexafluorophosphate (LiPF{sub 6}) in ethylene carbonate/dimethyl carbonate (EC/DMC) electrolytes for 1 h. The membranes were characterized by scanning electron microscope (SEM), porosity and electrolyte uptake and performance in battery cell. The results showed that both nano-clay and PVP have significant impacts on the improvement of PVDF membranes to be used as polymer electrolyte.« less

Improved electrochemical properties of a coin cell using LiMn 1.5Ni 0.5O 4 as cathode in the 5 V range

NASA Astrophysics Data System (ADS)

Singhal, Rahul; Das, Suprem R.; Oviedo, Osbert; Tomar, Maharaj S.; Katiyar, Ram S.

Phase pure LiMn 1.5Ni 0.5O 4 powders were synthesized by a chemical synthesis route and were subsequently characterized as cathode materials in a Li-ion coin cell comprising a Li anode and lithium hexafluorophosphate (LiPF 6), dissolved in dimethyl carbonate (DMC) + ethylene carbonate (EC) [1:1, v/v ratio] as electrolyte. The spinel structure and phase purity of the powders were characterized using X-ray diffraction and micro-Raman spectroscopy. The presence of both oxidation and reduction peaks in the cyclic voltammogram revealed Li + extraction and insertion from the spinel structure. The charge-discharge characteristics of the coin cell were performed in the 3.0-4.8 V range. An initial discharge capacity of ∼140 mAh g -1 was obtained with 94% initial discharge capacity retention after 50 repeated cycles. The microstructures and compositions of the cathode before and after electrochemistry were investigated using scanning electron microscopy and energy-dispersive analysis by X-ray analysis, respectively. Using X-ray diffraction, Raman spectroscopy and electrochemical analysis, we correlated the structural stability and the electrochemical performance of this cathode.

Influence of surface oxygenated groups on the formation of active Cu species and the catalytic activity of Cu/AC catalyst for the synthesis of dimethyl carbonate

NASA Astrophysics Data System (ADS)

Zhang, Guoqiang; Li, Zhong; Zheng, Huayan; Hao, Zhiqiang; Wang, Xia; Wang, Jiajun

2016-12-01

Activated carbon (AC) supported Cu catalysts are employed to study the influence of surface oxygenated groups on the formation of active Cu species and the catalytic activity of Cu/AC catalyst for oxidative carbonylation of methanol to dimethyl carbonate (DMC). The AC supports are thermal treated under different temperatures in order to adjust the levels of surface oxygenated groups. The AC supports are characterized by BET, TPD-MS and XRD, and the Cu/AC catalysts are characterized by BET, XRD, TEM, XPS, AAS, CH3OH-TPD and N2O chemisorption. The results show that as the treatment temperature is below 800 °C, the BET surface area of the corresponding AC supports are nearly unchanged and close to that of the original AC (1529.6 m2/g). But as the thermal treatment temperature is elevated from 1000 to 1600 °C, the BET surface area of AC supports gradually decreases from 1407.6 to 972.2 m2/g. After loading of Cu, the BET surface area of copper catalysts is in the range of 834.4 to 1545.3 m2/g, which is slightly less than that of the respective supports. When AC is thermal treated at 400 and 600 °C, the unstable carboxylic acid and anhydrides groups are selectively removed, which has weakened the mobility and agglomeration of Cu species during the calcination process, and thus improve the Cu species dispersion over AC support. But as the treatment temperature is elevated from 600 °C to 1200 °C, the Cu species dispersion begins to decline suggesting further removal of stable surface oxygenated groups is unfavorable for Cu species dispersion. Moreover, higher thermal treatment temperature (above 1200 °C) promotes the graphitization degree of AC and leds to the decrease of Cu loading on AC support. Meanwhile, the removal of surface oxygenated groups by thermal treatment is conducive to the formation of more π-sites, and thus promote the reduction of Cu2+ to Cu+ and Cu0 as active centers. The specific surface area of (Cu+ + Cu0) is improved by thermal treatment of AC, however, the space time yield of DMC on unit specific surface area of (Cu+ + Cu0) is in the range of 23.1-49.1 mg h-1 m-2, which is much less than that (77.6 mg h-1 m-2) of the original catalyst. The possible reason is that the removal of surface oxygenated groups results in AC support transforms from hydrophilicity to hydrophobicity, which is detrimental for the adsorption of CH3OH resulting in the decreased local concentration of CH3OH on active Cu species.

Electrolytes for Li-Ion Cells in Low Temperature Applications

NASA Technical Reports Server (NTRS)

Smart, M. C.; Ratnakumar, B. V.; Surampudi, S.

2000-01-01

Prototype AA-size lithium-ion cells have been demonstrated to operate effectively at temperatures as low as -30 to -40 C. These improvements in low temperature cell performance have been realized by the incorporation of ethylene carbonate-based electrolytes which possess low melting, low viscosity cosolvents, such as methyl acetate, ethyl acetate, gamma-butyrolactone, and ethyl methyl carbonate. The cells containing a 0.75M LiPF6 EC+DEC+DMC+EMC (1:1:1:1) electrolyte displayed the best performance at -30 C (> 90% of the room temperature capacity at approximately C/15 rate), whereas, at -40 C the cells with the 0.75M LiPF6 EC+DEC+DMC+MA (1:1:1:1) and 0.75M LiPF6 EC+DEC+DMC+EA (1:1:1:1) electrolytes showed superior performance.

Effects of ammonia load on glucose metabolism by isolated ovine duodenal mucosa.

PubMed

Regmi, P R; Dixon, W T; Oba, M

2008-09-01

To determine the effects of ammonia load on glucose metabolism in ruminant small intestinal tissues, duodenal mucosal cells (DMC) were isolated from growing female sheep (n = 10; 46. 0 +/- 0. 8 kg of BW) fed diets differing in CP content: high (19. 4%) vs. low (13. 1%). Ammonia concentration in the duodenal digesta fluid was greater for sheep fed a high CP diet compared with those fed a low CP diet (16. 4 +/- 1. 0 vs. 9. 1 +/- 1. 8 mM). The isolated primary mucosal cells were incubated for 90 min with [2-(13)C] glucose (3 mM) and ammonium chloride (0, 0. 1, 1, 5, 10, 20, or 50 mM) in Krebs-Ringer HEPES buffer. It was hypothesized that DMC would increase glucose carbon utilization for the synthesis of nonessential AA when the ammonia concentration in the incubation media increased. However, utilization of glucose carbon for alanine synthesis decreased linearly (P = 0. 03) as the ammonia concentration in the incubation media increased. Furthermore, glucose disappearance and utilization of glucose carbon for aspartate synthesis were not affected (P > 0. 47) by the ammonia concentration. Contrarily, in vitro glucose disappearance was greater (P = 0. 03) for DMC isolated from sheep fed a low CP diet vs. a high CP diet [14. 6 +/- 1. 6 vs. 8. 6 +/- 1. 3 nmol.(10(6) cells)(-1).(90 min) (-1)], and hexokinase activity was greater (P = 0. 01) in the mucosa of sheep fed a low CP diet compared with a high CP diet (1. 22 +/- 0. 05 vs. 1. 04 +/- 0. 02 mUnit/mg of protein). These observations indicate that ammonia load does not affect the extent of glucose utilization by DMC, and that glucose carbon may not play a significant role for the synthesis of alanine, aspartate, or glutamate when DMC are exposed to increased concentrations of ammonia.

A high performance ceramic-polymer separator for lithium batteries

NASA Astrophysics Data System (ADS)

Kumar, Jitendra; Kichambare, Padmakar; Rai, Amarendra K.; Bhattacharya, Rabi; Rodrigues, Stanley; Subramanyam, Guru

2016-01-01

A three-layered (ceramic-polymer-ceramic) hybrid separator was prepared by coating ceramic electrolyte [lithium aluminum germanium phosphate (LAGP)] over both sides of polyethylene (PE) polymer membrane using electron beam physical vapor deposition (EB-PVD) technique. Ionic conductivities of membranes were evaluated after soaking PE and LAGP/PE/LAGP membranes in a 1 Molar (1M) lithium hexafluroarsenate (LiAsF6) electrolyte in ethylene carbonate (EC), dimethyl carbonate (DMC) and ethylmethyl carbonate (EMC) in volume ratio (1:1:1). Scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques were employed to evaluate morphology and structure of the separators before and after cycling performance tests to better understand structure-property correlation. As compared to regular PE separator, LAGP/PE/LAGP hybrid separator showed: (i) higher liquid electrolyte uptake, (ii) higher ionic conductivity, (iii) lower interfacial resistance with lithium and (iv) lower cell voltage polarization during lithium cycling at high current density of 1.3 mA cm-2 at room temperature. The enhanced performance is attributed to higher liquid uptake, LAGP-assisted faster ion conduction and dendrite prevention. Optimization of density and thickness of LAGP layer on PE or other membranes through manipulation of PVD deposition parameters will enable practical applications of this novel hybrid separator in rechargeable lithium batteries with high energy, high power, longer cycle life, and higher safety level.

LiGa(OTf)(sub 4) as an Electrolyte Salt for Li-Ion Cells

NASA Technical Reports Server (NTRS)

Reddy, V. Prakash; Prakash, G. K. Syria; Hu, Jinbo; Yan, Ping; Smart, Marshall; Bugga, ratnakumar; Chin, Keith; Surampudi, Subarao

2008-01-01

Lithium tetrakis(trifluoromethane sulfo - nato)gallate [abbreviated "LiGa(OTf)4" (wherein "OTf" signifies trifluoro - methanesulfonate)] has been found to be promising as an electrolyte salt for incorporation into both liquid and polymer electrolytes in both rechargeable and non-rechargeable lithium-ion electrochemical cells. This and other ingredients have been investigated in continuing research oriented toward im proving the performances of rechargeable lithium-ion electrochemical cells, especially at low temperatures. This research at earlier stages, and the underlying physical and chemical principles, were reported in numerous previous NASA Tech Briefs articles. As described in more detail in those articles, lithiumion cells most commonly contain nonaqueous electrolyte solutions consisting of lithium hexafluorophosphate (LiPF6) dissolved in mixtures of cyclic and linear alkyl carbonates, including ethylene carbonate (EC), propylene carbonate (PC), dimethyl carbonate (DMC), diethyl carbonate (DEC), and ethyl methyl carbonate (EMC). Although such LiPF6-based electrolyte solutions are generally highly ionically conductive and electrochemically stable, as needed for good cell performance, there is interest in identifying alternate lithium electrolyte salts that, relative to LiPF6, are more resilient at high temperature and are less expensive. Experiments have been performed on LiGa(OTf)4 as well as on several other candidate lithium salts in pursuit of this interest. As part of these experiments, LiGa(OTf)4 was synthesized by the reaction of Ga(OTf)3 with an equimolar portion of LiOTf in a solvent consisting of anhydrous acetonitrile. Evaporation of the solvent yielded LiGa(OTf)4 as a colorless crystalline solid. The LiGa(OTf)4 and the other salts were incorporated into solutions with PC and DMC. The resulting electrolyte solutions exhibited reasonably high ionic conductivities over a relatively wide temperature range down to 40 C (see figure). In cyclic voltammetry measurements, LiGa(OTf)4 and the other salts exhibited acceptably high electrochemical stability over the relatively wide potential window of 0 to 5 V versus Li+/Li. 13C nuclear-magneticresonance measurements yielded results that suggested that in comparison with the other candidate salts, LiGa(OTf)4 exhibits less ion pairing. Planned further development will include optimization of the salt and solvent contents of such electrolyte solutions and incorporation of LiGa(OTf)4 into gel and solid-state polymer electrolytes. Of the salts, LiGa(OTf)4 is expected to be especially desirable for incorporation into lithium polymer electrolytes, wherein decreased ion pairing is advantageous and the large delocalized anions can exert a plasticizing effect.

Catalytic oxidation of dimethyl ether

DOEpatents

Zelenay, Piotr; Wu, Gang; Johnston, Christina M.; Li, Qing

2016-05-10

A composition for oxidizing dimethyl ether includes an alloy supported on carbon, the alloy being of platinum, ruthenium, and palladium. A process for oxidizing dimethyl ether involves exposing dimethyl ether to a carbon-supported alloy of platinum, ruthenium, and palladium under conditions sufficient to electrochemically oxidize the dimethyl ether.

Thermodynamic equilibrium calculations of dimethyl ether steam reforming and dimethyl ether hydrolysis

NASA Astrophysics Data System (ADS)

Semelsberger, Troy A.; Borup, Rodney L.

The production of a hydrogen-rich fuel-cell feed by dimethyl ether (DME) steam reforming was investigated using calculations of thermodynamic equilibrium as a function of steam-to-carbon ratio (0.00-4.00), temperature (100-600 °C), pressure (1-5 atm), and product species. Species considered were acetone, acetylene, carbon dioxide, carbon monoxide, dimethyl ether, ethane, ethanol, ethylene, formaldehyde, formic acid, hydrogen, isopropanol, methane, methanol, methyl-ethyl ether, n-propanol and water. Thermodynamic equilibrium calculations of DME steam reforming indicate complete conversion of dimethyl ether to hydrogen, carbon monoxide and carbon dioxide at temperatures greater than 200 °C and steam-to-carbon ratios greater than 1.25 at atmospheric pressure ( P = 1 atm). Increasing the operating pressure shifts the equilibrium toward the reactants; increasing the pressure from 1 to 5 atm decreases the conversion of dimethyl ether from 99.5 to 76.2%. The trend of thermodynamically stable products in decreasing mole fraction is methane, ethane, isopropyl alcohol, acetone, n-propanol, ethylene, ethanol, methyl-ethyl ether and methanol-formaldehyde, formic acid, and acetylene were not observed. Based on the equilibrium calculations, the optimal processing conditions for dimethyl ether steam reforming occur at a steam-to-carbon ratio of 1.50, a pressure of 1 atm, and a temperature of 200 °C. These thermodynamic equilibrium calculations show dimethyl ether processed with steam will produce hydrogen-rich fuel-cell feeds—with hydrogen concentrations exceeding 70%. The conversion of dimethyl ether via hydrolysis (considering methanol as the only product) is limited by thermodynamic equilibrium. Equilibrium conversion increases with temperature and steam-to-carbon ratio. A maximum dimethyl ether conversion of 62% is achieved at a steam-to-carbon ratio of 5.00 and a processing temperature of 600 °C.

Biosynthesis of glycerol carbonate from glycerol by lipase in dimethyl carbonate as the solvent.

PubMed

Lee, Kyung Hwa; Park, Chang-Ho; Lee, Eun Yeol

2010-11-01

Glycerol carbonate was synthesized from renewable glycerol and dimethyl carbonate using lipase in solvent-free reaction system in which excess dimethyl carbonate played as the reaction medium. A variety of lipases have been tested for their abilities to catalyze transesterification reaction, and Candida antartica lipase B and Novozyme 435 exhibited higher catalytic activities. The silica-coated glycerol with a 1:1 ratio was supplied to prevent two-phase formation between hydrophobic dimethyl carbonate and hydrophilic glycerol. Glycerol carbonate was successfully synthesized with more than 90% conversion from dimethyl carbonate and glycerol with a molar ratio of 10 using Novozyme 435-catalyzed transesterification at 70 °C. The Novozyme 435 [5% (w/w) and 20% (w/w)] and silica gel were more than four times recycled with good stability in a repeated batch operation for the solvent-free synthesis of glycerol carbonate.

Thiol-ene chemistry guided preparation of thiolated polymeric nanocomposite for anodic stripping voltammetric analysis of Cd2+ and Pb2+.

PubMed

Su, Zhaohong; Liu, Ying; Zhang, Yi; Xie, Qingji; Chen, Li; Huang, Yi; Fu, Yingchun; Meng, Yue; Li, Xuejiao; Ma, Ming; Yao, Shouzhuo

2013-02-21

We report on the thiol-ene chemistry guided preparation of a novel thiolated polymeric nanocomposite involving polyaniline (PANI), a functionalized thiol, e.g., sulfur-rich 2,5-dimercapto-1,3,4-thiadiazole (DMcT), and multiwalled carbon nanotubes (MWCNTs) for the sensitive differential pulse anodic stripping voltammetric determination of Cd(2+) and Pb(2+) on a glassy carbon electrode (GCE). Briefly, the thiol-ene reaction of a thiol with oxidized PANI that was chemically synthesized in the presence of solution-dispersed acidified MWCNTs yielded a thiolated polymeric nanocomposite of thiol-PANI/MWCNTs. The thiols examined include DMcT, 1,6-hexanedithiol and β-mercaptoethanol. Quartz crystal microbalance, cyclic voltammetry, scanning electron microscopy, Fourier transform infrared spectroscopy and ultraviolet-visible spectroscopy were used for film characterization and process monitoring. Under the optimized conditions, the obtained Bi/Nafion/DMcT-PANI/MWCNTs/GCE can sensitively sense Cd(2+) and Pb(2+) with limits of detection of 0.01 and 0.04 μg L(-1), respectively.

Natural derivatives of curcumin attenuate the Wnt/{beta}-catenin pathway through down-regulation of the transcriptional coactivator p300

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ryu, Min-Jung; Cho, Munju; Song, Jie-Young

2008-12-26

Curcumin, a component of turmeric (Curcuma longa), has been reported to suppress {beta}-catenin response transcription (CRT), which is aberrantly activated in colorectal cancer. However, the effects of its natural analogs (demethoxycurcumin [DMC] and bisdemethoxycurcumin [BDMC]) and metabolite (tetrahydrocurcumin [THC]) on the Wnt/{beta}-catenin pathway have not been investigated. Here, we show that DMC and BDMC suppressed CRT that was activated by Wnt3a conditioned-medium (Wnt3a-CM) without altering the level of intracellular {beta}-catenin, and inhibited the growth of various colon cancer cells, with comparable potency to curcumin. Additionally, DMC and BDMC down-regulated p300, which is a positive regulator of the Wnt/{beta}-catenin pathway. Notably,more » THC also inhibited CRT and cell proliferation, but to a much lesser degree than curcumin, DMC, or BDMC, indicating that the conjugated bonds in the central seven-carbon chain of curcuminoids are essential for the inhibition of Wnt/{beta}-catenin pathway and the anti-proliferative activity of curcuminoids. Thus, our findings suggest that curcumin derivatives inhibit the Wnt/{beta}-catenin pathway by decreasing the amount of the transcriptional coactivator p300.« less

Gel polymer electrolytes based on nanofibrous polyacrylonitrile–acrylate for lithium batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Dul-Sun; Woo, Jang Chang; Youk, Ji Ho, E-mail: youk@inha.ac.kr

2014-10-15

Graphical abstract: - Highlights: • Nanofibrous polyacrylonitrile–acrylate membranes were prepared by electrospinning. • Trimethylolpropane triacrylate was used as a crosslinking agent of fibers. • The GPE based on PAN–acrylate (1/0.5) showed good electrochemical properties. - Abstract: Nanofibrous membranes for gel polymer electrolytes (GPEs) were prepared by electrospinning a mixture of polyacrylonitrile (PAN) and trimethylolpropane triacrylate (TMPTA) at weight ratios of 1/0.5 and 1/1. TMPTA is used to achieve crosslinking of fibers thereby improving mechanical strength. The average fiber diameters increased with increasing TMPTA concentration and the mechanical strength was also improved due to the enhanced crosslinking of fibers. GPEs basedmore » on electrospun membranes were prepared by soaking them in a liquid electrolyte of 1 M LiPF{sub 6} in ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1, v/v). The electrolyte uptake and ionic conductivity of GPEs based on PAN and PAN–acrylate (weight ratio; 1/1 and 1/0.5) were investigated. Ionic conductivity of GPEs based on PAN–acrylate was the highest for PAN/acrylate (1/0.5) due to the proper swelling of fibers and good affinity with liquid electrolyte. Both GPEs based on PAN and PAN–acrylate membranes show good oxidation stability, >5.0 V vs. Li/Li{sup +}. Cells with GPEs based on PAN–acrylate (1/0.5) showed remarkable cycle performance with high initial discharge capacity and low capacity fading.« less

Automated microfluidic platform for studies of carbon dioxide dissolution and solubility in physical solvents.

PubMed

Abolhasani, Milad; Singh, Mayank; Kumacheva, Eugenia; Günther, Axel

2012-05-07

We present an automated microfluidic (MF) approach for the systematic and rapid investigation of carbon dioxide (CO(2)) mass transfer and solubility in physical solvents. Uniformly sized bubbles of CO(2) with lengths exceeding the width of the microchannel (plugs) were isothermally generated in a co-flowing physical solvent within a gas-impermeable, silicon-based MF platform that is compatible with a wide range of solvents, temperatures and pressures. We dynamically determined the volume reduction of the plugs from images that were accommodated within a single field of view, six different downstream locations of the microchannel at any given flow condition. Evaluating plug sizes in real time allowed our automated strategy to suitably select inlet pressures and solvent flow rates such that otherwise dynamically self-selecting parameters (e.g., the plug size, the solvent segment size, and the plug velocity) could be either kept constant or systematically altered. Specifically, if a constant slug length was imposed, the volumetric dissolution rate of CO(2) could be deduced from the measured rate of plug shrinkage. The solubility of CO(2) in the physical solvent was obtained from a comparison between the terminal and the initial plug sizes. Solubility data were acquired every 5 min and were within 2-5% accuracy as compared to literature data. A parameter space consisting of the plug length, solvent slug length and plug velocity at the microchannel inlet was established for different CO(2)-solvent pairs with high and low gas solubilities. In a case study, we selected the gas-liquid pair CO(2)-dimethyl carbonate (DMC) and volumetric mass transfer coefficients 4-30 s(-1) (translating into mass transfer times between 0.25 s and 0.03 s), and Henry's constants, within the range of 6-12 MPa.

Microbial Transformations of Selenium

PubMed Central

Doran, J. W.; Alexander, M.

1977-01-01

Resting cell suspensions of a strain of Corynebacterium isolated from soil formed dimethyl selenide from selenate, selenite, elemental selenium, selenomethionine, selenocystine, and methaneseleninate. Extracts of the bacterium catalyzed the production of dimethyl selenide from selenite, elemental selenium, and methaneseleninate, and methylation of the inorganic Se compounds was enhanced by S-adenosylmethionine. Neither trimethylselenonium nor methaneselenonate was metabolized by the Corynebacterium. Resting cell suspensions of a methionine-utilizing pseudomonad converted selenomethionine to dimethyl diselenide. Six of 10 microorganisms able to grow on cystine used selenocystine as a sole source of carbon and formed elemental selenium, and one of the isolates, a pseudomonad, was found also to produce selenide. Soil enrichments converted trimethylselenonium to dimethyl selenide. Bacteria capable of utilizing trimethylselenonium, dimethyl selenide, and dimethyl diselenide as carbon sources were isolated from soil. PMID:16345188

Thermodynamic equilibrium calculations of hydrogen production from the combined processes of dimethyl ether steam reforming and partial oxidation

NASA Astrophysics Data System (ADS)

Semelsberger, Troy A.; Borup, Rodney L.

Thermodynamic analyses of producing a hydrogen-rich fuel-cell feed from the combined processes of dimethyl ether (DME) partial oxidation and steam reforming were investigated as a function of oxygen-to-carbon ratio (0.00-2.80), steam-to-carbon ratio (0.00-4.00), temperature (100 °C-600 °C), pressure (1-5 atm) and product species. Thermodynamically, dimethyl ether processed with air and steam generates hydrogen-rich fuel-cell feeds; however, the hydrogen concentration is less than that for pure DME steam reforming. Results of the thermodynamic processing of dimethyl ether indicate the complete conversion of dimethyl ether to hydrogen, carbon monoxide and carbon dioxide for temperatures greater than 200 °C, oxygen-to-carbon ratios greater than 0.00 and steam-to-carbon ratios greater than 1.25 at atmospheric pressure (P = 1 atm). Increasing the operating pressure has negligible effects on the hydrogen content. Thermodynamically, dimethyl ether can produce concentrations of hydrogen and carbon monoxide of 52% and 2.2%, respectively, at a temperature of 300 °C, and oxygen-to-carbon ratio of 0.40, a pressure of 1 atm and a steam-to-carbon ratio of 1.50. The order of thermodynamically stable products (excluding H 2, CO, CO 2, DME, NH 3 and H 2O) in decreasing mole fraction is methane, ethane, isopropyl alcohol, acetone, n-propanol, ethylene, ethanol and methyl-ethyl ether; trace amounts of formaldehyde, formic acid and methanol are observed. Ammonia and hydrogen cyanide are also thermodynamically favored products. Ammonia is favored at low temperatures in the range of oxygen-to-carbon ratios of 0.40-2.50 regardless of the steam-to-carbon ratio employed. The maximum ammonia content (i.e., 40%) occurs at an oxygen-to-carbon ratio of 0.40, a steam-to-carbon ratio of 1.00 and a temperature of 100 °C. Hydrogen cyanide is favored at high temperatures and low oxygen-to-carbon ratios with a maximum of 3.18% occurring at an oxygen-to-carbon ratio of 0.40 and a steam-to-carbon ratio of 0.00 in the temperature range of 400 °C-500 °C. Increasing the system pressure shifts the equilibrium toward ammonia and hydrogen cyanide.

AtDMC1, the Arabidopsis homologue of the yeast DMC1 gene: characterization, transposon-induced allelic variation and meiosis-associated expression.

PubMed

Klimyuk, V I; Jones, J D

1997-01-01

Based on homologies between the yeast DMC1 and the lily LIM15 meiosis-specific genes, degenerate PCR primers were designed that amplified the Arabidopsis DMC1 gene (AtDMC1). AtDMC1 genomic DNA (8 kb) was sequenced, and the transcript was characterized by reverse transcriptase-polymerase chain reaction (RT-PCR) and by 5' and 3' RACE (rapid amplification of cDNA ends). The AtDMC1 gene contains 15 exons and 14 introns. RNA in situ hybridization analysis showed that expression of the AtDMC1 is restricted to pollen mother cells in anthers and to megaspore mother cells in ovules. The AtDMC1 promoter was fused to the GUS reporter gene, and conferred meiosis-associated expression in both male and female floral lineages. Comparison of AtDMC1 isolated from Landsberg erecta ecotype to its Columbia allele ArLIM15, revealed the presence of a 1874 bp transposon-like element within the promoter region of ArLIM15. RT-PCR analysis showed that the expression levels of AtDMC1 and ArLIM15 are similar. Possible uses for the AtDMC1 promoter are discussed.

Diversity or disarray? A systematic review of decision-making capacity for treatment and research in schizophrenia and other non-affective psychoses.

PubMed

Spencer, B W J; Shields, G; Gergel, T; Hotopf, M; Owen, G S

2017-08-01

Valid consent for treatment or research participation requires that an individual has decision-making capacity (DMC), which is the ability to make a specific decision. There is evidence that the psychopathology of schizophrenia can compromise DMC. The objective of this review was to examine the presence or absence of DMC in schizophrenia and the socio-demographic/psychopathological factors associated. We searched three databases Embase, Ovid MEDLINE(R), and PsycINFO for studies reporting data on the proportion of DMC for treatment and research (DMC-T and DMC-R), and/or socio-demographic/psychopathological associations with ability to make such decisions, in people with schizophrenia and related illnesses. A total of 40 studies were identified. While high levels of heterogeneity limited direct comparison, meta-analysis of inpatient data showed that DMC-T was present in 48% of people. Insight was strongly associated with DMC-T. Neurocognitive deficits were strongly associated with lack of DMC-R and to a lesser extent DMC-T. With the exception of years of education, there was no evidence for an association with socio-demographic factors. Insight and neurocognitive deficits are most closely associated with DMC in schizophrenia. The lack of an association with socio-demographic factors dispels common misperceptions regarding DMC and characteristics such as age. Although our results reveal a wide spectrum of DMC-T and DMC-R in schizophrenia, this could be partly due to the complexity of the DMC construct and the heterogeneity of existing studies. To facilitate systematic review research, there is a need for improvement within research study design and increased consistency of concepts and tools.

Kinetic Evaluation of Lipid Oils Conversion to Biofuel Using Layered Double Hydroxide Doped with Triazabicyclodece Catalyst

NASA Astrophysics Data System (ADS)

Nato Lopez, Frank D.

Worldwide, there is an ever increasing need for sustainable, renewable fuels that will accommodate the rapidly increasing energy demand and provide independence from fossil fuels. The search for a sustainable alternative to petroleum based fuels has been a great challenge to the scientific community; therefore, great efforts are being made to overcome the fossil fuels dependence by exploring the prominent field of biofuels (bioethanol and biodiesel). Traditional biodiesel is produced from feedstocks such as vegetable oils and animal fats by converting the triglycerides with methanol in the presence of a homogeneous catalyst to produce fatty acid methyl esters (FAMEs). However, drawbacks of this process are the undesired glycerol byproduct and post reaction processing, including separation from reaction mixture, that results in high costs factors. In the present work, the reaction kinetics of a glycerol-free biodiesel method is studied. This method consists of the transesterification of a vegetable oil (i.e. canola oil) using dimethyl carbonate (DMC) as an alternative methylating agent in presence of layered double hydroxides doped with triazabicyclodecene catalyst (a basic organocatalyst). Furthermore, is theorized that this heterogeneous catalyst (TBD/LDH) simultaneously converts both FFAs and triglycerides due to acid sites formed by Al3+ active sites of the LDH structure. Additionally, the versatility of the Raman in situ technique was used as quantitative analysis tool to monitor the reaction kinetics and collect real time data.

Dmc1 of Schizosaccharomyces pombe plays a role in meiotic recombination.

PubMed

Fukushima, K; Tanaka, Y; Nabeshima, K; Yoneki, T; Tougan, T; Tanaka, S; Nojima, H

2000-07-15

We report here a Schizosaccharomyces pombe gene (dmc1(+)) that resembles budding yeast DMC1 in the region immediately upstream of the rad24(+) gene. We showed by northern and Southern blot analysis that dmc1(+) and rad24(+) are co-transcribed as a bicistronic mRNA of 2.8 kb with meiotic specificity, whereas rad24(+) itself is constitutively transcribed as a 1.0-kb mRNA species during meiosis. Induction of the bicistronic transcript is under the control of a meiosis-specific transcription factor, Ste11. Disruption of both dmc1(+) and rad24(+) had no effect on mitosis or spore formation, and dmc1Delta cells displayed no change in sensitivity to UV or gamma irradiation relative to the wild type. Tetrad analysis indicated that Dmc1 is involved in meiotic recombination. Analysis of gene conversion frequencies using single and double mutants of dmc1 and rhp51 indicated that both Dmc1 and Rhp51 function in meiotic gene conversion. These observations, together with a high level of sequence identity, indicate that the dmc1(+) gene of S. POMBE: is a structural homolog of budding yeast DMC1, sharing both similar and distinct functions in meiosis.

INTRAMOLECULAR MOTION AND REORIENTATIONAL BARRIERS IN 9-FLUORENONE, 4-METHYL-9-FLUORENONE AND 4,5-DIMETHYL-9-FLUORENONE

EPA Science Inventory

Carbon-13 nuclear magnetic resonance spin-lattice relaxation times and nuclear Overhauser enhancements were measured as functions of temperature for the hydrogen-bearing carbons in 9-fluorenone, 4-methyl-9-fluorenone, and 4,5-dimethyl-9-fluorenone. Reorientational diffusion const...

Dmc1 Functions in a Saccharomyces Cerevisiae Meiotic Pathway That Is Largely Independent of the Rad51 Pathway

PubMed Central

Dresser, M. E.; Ewing, D. J.; Conrad, M. N.; Dominguez, A. M.; Barstead, R.; Jiang, H.; Kodadek, T.

1997-01-01

Meiotic recombination in the yeast Saccharomyces cerevisiae requires two similar recA-like proteins, Dmc1p and Rad51p. A screen for dominant meiotic mutants provided DMC1-G126D, a dominant allele mutated in the conserved ATP-binding site (specifically, the A-loop motif) that confers a null phenotype. A recessive null allele, dmc1-K69E, was isolated as an intragenic suppressor of DMC1-G126D. Dmc1-K69Ep, unlike Dmc1p, does not interact homotypically in a two-hybrid assay, although it does interact with other fusion proteins identified by two-hybrid screen with Dmc1p. Dmc1p, unlike Rad51p, does not interact in the two-hybrid assay with Rad52p or Rad54p. However, Dmc1p does interact with Tid1p, a Rad54p homologue, with Tid4p, a Rad16p homologue, and with other fusion proteins that do not interact with Rad51p, suggesting that Dmc1p and Rad51p function in separate, though possibly overlapping, recombinational repair complexes. Epistasis analysis suggests that DMC1 and RAD51 function in separate pathways responsible for meiotic recombination. Taken together, our results are consistent with a requirement for DMC1 for meiosis-specific entry of DNA double-strand break ends into chromatin. Interestingly, the pattern on CHEF gels of chromosome fragments that result from meiotic DNA double-strand break formation is different in DMC1 mutant strains from that seen in rad50S strains. PMID:9335591

Methylation of 2-Naphthol Using Dimethyl Carbonate under Continuous-Flow Gas-Phase Conditions

ERIC Educational Resources Information Center

Tundo, Pietro; Rosamilia, Anthony E.; Arico, Fabio

2010-01-01

This experiment investigates the methylation of 2-naphthol with dimethyl carbonate. The volatility of the substrates, products, and co-products allows the reaction to be performed using a continuous-flow gas-phase setup at ambient pressure. The reaction uses catalytic quantities of base, achieves high conversion, produces little waste, and…

Spectro-Electrochemical Examination of the Formation of Dimethyl Carbonate from CO and Methanol at Different Electrode Materials

PubMed Central

2017-01-01

In this work, we report a fundamental mechanistic study of the electrochemical oxidative carbonylation of methanol with CO for the synthesis of dimethyl carbonate on metallic electrodes at low overpotentials. For the first time, the reaction was shown to take place on the metallic catalysts without need of oxidized metals or additives. Moreover, in-situ spectroelectrochemical techniques were applied to this electrosynthesis reaction in order to reveal the reaction intermediates and to shed light into the reaction mechanism. Fourier transformed infrared spectroscopy was used with different electrode materials (Au, Pd, Pt, and Ag) to assess the effect of the electrode material on the reaction and the dependence of products and intermediates on the applied potentials. It was observed that the dimethyl carbonate is only formed when the electrode is able to decompose/oxidize MeOH to form (adsorbed) methoxy groups that can further react with CO to dimethyl carbonate. Furthermore, the electrode needs to adsorb CO not too strongly; otherwise, further reaction will be inhibited because of surface poisoning by CO. PMID:28929754

Layered double hydroxide catalyst for the conversion of crude vegetable oils to a sustainable biofuel

NASA Astrophysics Data System (ADS)

Mollaeian, Keyvan

Over the last two decades, the U.S. has developed the production of biodiesel, a mixture of fatty acid methyl esters, using chiefly vegetable oils as feedstocks. However, there is much concern about the availability of high-quality vegetable oils for longterm biodiesel production. Problems have also risen due to the production of glycerol, an unwanted byproduct, as well as the need for process wash water. Therefore, this study was initiated to produce not only fatty acid methyl esters (FAMEs) but also fatty acid glycerol carbonates (FAGCs) by replacing methanol with dimethyl carbonate (DMC). The process would have no unnecessary byproducts and would be a simplified process compared to traditional biodiesel. In addition, this altering of the methylating agent could convert triglycerides, free fatty acids, and phospholipids to a sustainable biofuel. In this project, Mg-Al Layered Double Hydroxide (LDH) was optimized by calcination in different temperature varied from 250°C to 450°C. The gallery between layers was increased by intercalating sodium dodecylsulfate (SDS). During catalyst preparation, the pH was controlled ~10. In our experiment, triazabicyclodecene (TBD) was attached with trimethoxysilane (3GPS) as a coupling agent, and N-cetyl-N,N,N-trimethylammonium bromide (CTAB) was added to remove SDS from the catalyst. The catalyst was characterized by XRD, FTIR, and Raman spectroscopy. The effect of the heterogeneous catalyst on the conversion of canola oil, corn oil, and free fatty acids was investigated. To analyze the conversion of lipid oils to biofuel an in situ Raman spectroscopic method was developed. Catalyst synthesis methods and a proposed mechanism for converting triglycerides and free fatty acids to biofuel will be presented.

Solid-state Graft Copolymer Electrolytes for Lithium Battery Applications

PubMed Central

Hu, Qichao; Caputo, Antonio; Sadoway, Donald R.

2013-01-01

Battery safety has been a very important research area over the past decade. Commercially available lithium ion batteries employ low flash point (<80 °C), flammable, and volatile organic electrolytes. These organic based electrolyte systems are viable at ambient temperatures, but require a cooling system to ensure that temperatures do not exceed 80 °C. These cooling systems tend to increase battery costs and can malfunction which can lead to battery malfunction and explosions, thus endangering human life. Increases in petroleum prices lead to a huge demand for safe, electric hybrid vehicles that are more economically viable to operate as oil prices continue to rise. Existing organic based electrolytes used in lithium ion batteries are not applicable to high temperature automotive applications. A safer alternative to organic electrolytes is solid polymer electrolytes. This work will highlight the synthesis for a graft copolymer electrolyte (GCE) poly(oxyethylene) methacrylate (POEM) to a block with a lower glass transition temperature (Tg) poly(oxyethylene) acrylate (POEA). The conduction mechanism has been discussed and it has been demonstrated the relationship between polymer segmental motion and ionic conductivity indeed has a Vogel-Tammann-Fulcher (VTF) dependence. Batteries containing commercially available LP30 organic (LiPF6 in ethylene carbonate (EC):dimethyl carbonate (DMC) at a 1:1 ratio) and GCE were cycled at ambient temperature. It was found that at ambient temperature, the batteries containing GCE showed a greater overpotential when compared to LP30 electrolyte. However at temperatures greater than 60 °C, the GCE cell exhibited much lower overpotential due to fast polymer electrolyte conductivity and nearly the full theoretical specific capacity of 170 mAh/g was accessed. PMID:23963203

Solid-state graft copolymer electrolytes for lithium battery applications.

PubMed

Hu, Qichao; Caputo, Antonio; Sadoway, Donald R

2013-08-12

Battery safety has been a very important research area over the past decade. Commercially available lithium ion batteries employ low flash point (< 80 °C), flammable, and volatile organic electrolytes. These organic based electrolyte systems are viable at ambient temperatures, but require a cooling system to ensure that temperatures do not exceed 80 °C. These cooling systems tend to increase battery costs and can malfunction which can lead to battery malfunction and explosions, thus endangering human life. Increases in petroleum prices lead to a huge demand for safe, electric hybrid vehicles that are more economically viable to operate as oil prices continue to rise. Existing organic based electrolytes used in lithium ion batteries are not applicable to high temperature automotive applications. A safer alternative to organic electrolytes is solid polymer electrolytes. This work will highlight the synthesis for a graft copolymer electrolyte (GCE) poly(oxyethylene) methacrylate (POEM) to a block with a lower glass transition temperature (Tg) poly(oxyethylene) acrylate (POEA). The conduction mechanism has been discussed and it has been demonstrated the relationship between polymer segmental motion and ionic conductivity indeed has a Vogel-Tammann-Fulcher (VTF) dependence. Batteries containing commercially available LP30 organic (LiPF6 in ethylene carbonate (EC):dimethyl carbonate (DMC) at a 1:1 ratio) and GCE were cycled at ambient temperature. It was found that at ambient temperature, the batteries containing GCE showed a greater overpotential when compared to LP30 electrolyte. However at temperatures greater than 60 °C, the GCE cell exhibited much lower overpotential due to fast polymer electrolyte conductivity and nearly the full theoretical specific capacity of 170 mAh/g was accessed.

Decision-making competence predicts domain-specific risk attitudes

PubMed Central

Weller, Joshua A.; Ceschi, Andrea; Randolph, Caleb

2015-01-01

Decision-making competence (DMC) reflects individual differences in rational responding across several classic behavioral decision-making tasks. Although it has been associated with real-world risk behavior, less is known about the degree to which DMC contributes to specific components of risk attitudes. Utilizing a psychological risk-return framework, we examined the associations between risk attitudes and DMC. Italian community residents (n = 804) completed an online DMC measure, using a subset of the original Adult-DMC battery. Participants also completed a self-reported risk attitude measure for three components of risk attitudes (risk-taking, risk perceptions, and expected benefits) across six risk domains. Overall, greater performance on the DMC component scales were inversely, albeit modestly, associated with risk-taking tendencies. Structural equation modeling results revealed that DMC was associated with lower perceived expected benefits for all domains. In contrast, its association with perceived risks was more domain-specific. These analyses also revealed stronger indirect effects for the DMC → expected benefits → risk-taking path than the DMC → perceived risk → risk-taking path, especially for behaviors that may be considered more maladaptive in nature. These results suggest that DMC performance differentially impacts specific components of risk attitudes, and may be more strongly related to the evaluation of expected value of a specific behavior. PMID:26029128

Combining activated carbon adsorption with heterogeneous photocatalytic oxidation: Lack of synergy for biologically treated greywater and tetraethylene glycol dimethyl ether

PubMed Central

Gulyas, Holger; Argáez, Ángel Santiago Oria; Kong, Fanzhuo; Jorge, Carlos Liriano; Eggers, Susanne; Otterpohl, Ralf

2013-01-01

The aim of the study was to evaluate whether the addition of activated carbon in the photocatalytic oxidation of biologically pretreated greywater and of a polar aliphatic compound gives synergy, as previously demonstrated with phenol. Photocatalytic oxidation kinetics were recorded with fivefold concentrated biologically pretreated greywater and with aqueous tetraethylene glycol dimethyl ether solutions using a UV lamp and the photocatalyst TiO2 P25 in the presence and the absence of powdered activated carbon. The synergy factor, SF, was quantified as the ratio of photocatalytic oxidation rate constant in the presence of powdered activated carbon to the rate constant without activated carbon. No synergy was observed for the greywater concentrate (SF ≈ 1). For the aliphatic compound, tetraethylene glycol dimethyl ether, addition of activated carbon actually had an inhibiting effect on photocatalysis (SF < 1), while synergy was confirmed in reference experiments using aqueous phenol solutions. The absence of synergy for the greywater concentrate can be explained by low adsorbability of its organic constituents by activated carbon. Inhibition of the photocatalytic oxidation of tetraethylene glycol dimethyl ether by addition of powdered activated carbon was attributed to shading of the photocatalyst by the activated carbon particles. It was assumed that synergy in the hybrid process was limited to aromatic organics. Regardless of the lack of synergy in the case of biologically pretreated greywater, the addition of powdered activated carbon is advantageous since, due to additional adsorptive removal of organics, photocatalytic oxidation resulted in a 60% lower organic concentration when activated carbon was present after the same UV irradiation time. PMID:24191472

DLH1 is a functional Candida albicans homologue of the meiosis-specific gene DMC1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Diener, A.C.; Fink, G.R.

1996-06-01

DMC1/LIM15 homologue 1 (DLH1), a gene related to meiosis-specific genes, has been isolated from Candida albicans, a fungus thought not to undergo meiosis. The deduced protein sequence of DLH1 contains 74% amino acid identity with Dmc1p from Saccharomyces cerevisiae and 63% with Lim15p from the plant Lilium longiflorum, meiosis-specific homologous of Escherichia coli RecA. Candida DLH1 complements a dmc1/dmc1 null mutant in S. cerevisiae. High copy expression of DLH1 restores both sporulation and meiotic recombination to a Saccharomyces dmc1/{Delta}/dmc1{Delta} strain. Unlike the DMC1 gene, which is transcribed only in meiotic cells, the heterologous Candida DLH1 gene is transcribed in bothmore » vegetative and meiotic cells of S. cerevisiae. Transcription of DLH1 is not detected or induced in C. albicans under conditions that induce DMC1 and meiosis in S. cerevisiae. The presence of an intact homologue of a meiosis-specific gene in C. albicans raises the possibility that this organism has a cryptic meiotic pathway. 25 refs., 6 figs., 3 tabs.« less

U.S. Army’s Ground Vehicle Energy Storage R&D Programs & Goals

DTIC Science & Technology

2011-09-13

Results Li-ion Pack Testing ( NCA ) 13 CO CO2 Analyte Peak Concentration (ppm) 15 min Average Concentration (ppm) Carbon Monoxide (CO) 108939 81588...Carbonate (DMC) 21734 14307 Methyl Butyrate (MB) 47198 33368 • NCA Cell Chemistry • 173V, 6.4kWhr Pack • Prototype pack design (to determine worst case...including advanced prognostic and diagnostic capability) • O092-EP7 – Enhancing the Utilization Efficiency of Cathode Materials in the Li ion

Demethoxycurcumin Suppresses Migration and Invasion of Human Cervical Cancer HeLa Cells via Inhibition of NF-κB Pathways.

PubMed

Lin, Chin-Chung; Kuo, Chao-Lin; Huang, Yi-Ping; Chen, Cheng-Yen; Hsu, Ming-Jie; Chu, Yung Lin; Chueh, Fu-Shin; Chung, Jing-Gung

2018-05-01

Demethoxycurcumin (DMC), one of the curcuminoids present in turmeric, has been shown to induce cell death in many human cancer cell lines, however, there has not been any investigation on whether DMC inhibits metastatic activity in human cervical cancer cells in vitro. In the present study, DMC at 2.5-15 μM decreased cell number, thus, we used IC 20 (7.5 μM) for further investigation of its anti-metastatic activity in human cervical cancer HeLa cells. The wound healing, migration, invasion, zymography, and western blotting assays were used to investigate the effects of DMC on HeLa cells. The wound healing assay was used to show that DMC suppressed cell movement of HeLa cells. Furthermore, the trans-well chamber assay was used to show that DMC suppressed HeLa cell migration and invasion. Gelatin zymography assay did not show any significant effects of DMC on the gelatinolytic activity (MMP-2 and -9) in conditioned media of HeLa cells treated by DMC. Western blotting showed that DMC significantly reduced protein levels of GRB2, MMP-2, ERK1/2, N-cadherin and Ras but increased the levels of E-cadherin and NF-κB in HeLa cells. Confocal laser microscopy indicated that DMC increased NF-κB in HeLa cells confirming the results from Western blotting. DMC may be used as a novel anti-metastatic agent for the treatment of human cervical cancer in the future. Copyright© 2018, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

OsDMC1 Is Not Required for Homologous Pairing in Rice Meiosis1[OPEN

PubMed Central

Tang, Ding; Liu, Xiaofei; Du, Guijie; Shen, Yi; Li, Yafei; Cheng, Zhukuan

2016-01-01

Meiotic homologous recombination is pivotal to sexual reproduction. DMC1, a conserved recombinase, is involved in directing single-end invasion between interhomologs during meiotic recombination. In this study, we identified OsDMC1A and OsDMC1B, two closely related proteins in rice (Oryza sativa) with high sequence similarity to DMC1 proteins from other species. Analysis of Osdmc1a and Osdmc1b Tos17 insertion mutants indicated that these genes are functionally redundant. Immunolocalization analysis revealed OsDMC1 foci occurred at leptotene, which disappeared from late pachytene chromosomes in wild-type meiocytes. According to cytological analyses, homologous pairing is accomplished in the Osdmc1a Osdmc1b double mutant, but synapsis is seriously disrupted. The reduced number of bivalents and abnormal OsHEI10 foci in Osdmc1a Osdmc1b establishes an essential role for OsDMC1 in crossover formation. In the absence of OsDMC1, early recombination events probably occur normally, leading to normal localization of γH2AX, PAIR3, OsMRE11, OsCOM1, and OsRAD51C. Moreover, OsDMC1 was not detected in pairing-defective mutants, such as pair2, pair3, Oscom1, and Osrad51c, while it was loaded onto meiotic chromosomes in zep1, Osmer3, Oszip4, and Oshei10. Taken together, these results suggest that during meiosis, OsDMC1 is dispensable for homologous pairing in rice, which is quite different from the DMC1 homologs identified so far in other organisms. PMID:26960731

Process for producing dimethyl ether from synthesis gas

DOEpatents

Pierantozzi, R.

1985-06-04

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Process for producing dimethyl ether form synthesis gas

DOEpatents

Pierantozzi, Ronald

1985-01-01

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Stronger proteasomal inhibition and higher CHOP induction are responsible for more effective induction of paraptosis by dimethoxycurcumin than curcumin

PubMed Central

Yoon, M J; Kang, Y J; Lee, J A; Kim, I Y; Kim, M A; Lee, Y S; Park, J H; Lee, B Y; Kim, I A; Kim, H S; Kim, S-A; Yoon, A-R; Yun, C-O; Kim, E-Y; Lee, K; Choi, K S

2014-01-01

Although curcumin suppresses the growth of a variety of cancer cells, its poor absorption and low systemic bioavailability have limited its translation into clinics as an anticancer agent. In this study, we show that dimethoxycurcumin (DMC), a methylated, more stable analog of curcumin, is significantly more potent than curcumin in inducing cell death and reducing the clonogenicity of malignant breast cancer cells. Furthermore, DMC reduces the tumor growth of xenografted MDA-MB 435S cells more strongly than curcumin. We found that DMC induces paraptosis accompanied by excessive dilation of mitochondria and the endoplasmic reticulum (ER); this is similar to curcumin, but a much lower concentration of DMC is required to induce this process. DMC inhibits the proteasomal activity more strongly than curcumin, possibly causing severe ER stress and contributing to the observed dilation. DMC treatment upregulates the protein levels of CCAAT-enhancer-binding protein homologous protein (CHOP) and Noxa, and the small interfering RNA-mediated suppression of CHOP, but not Noxa, markedly attenuates DMC-induced ER dilation and cell death. Interestingly, DMC does not affect the viability, proteasomal activity or CHOP protein levels of human mammary epithelial cells, suggesting that DMC effectively induces paraptosis selectively in breast cancer cells, while sparing normal cells. Taken together, these results suggest that DMC triggers a stronger proteasome inhibition and higher induction of CHOP compared with curcumin, giving it more potent anticancer effects on malignant breast cancer cells. PMID:24625971

The impact of web services at the IRIS DMC

NASA Astrophysics Data System (ADS)

Weekly, R. T.; Trabant, C. M.; Ahern, T. K.; Stults, M.; Suleiman, Y. Y.; Van Fossen, M.; Weertman, B.

2015-12-01

The IRIS Data Management Center (DMC) has served the seismological community for nearly 25 years. In that time we have offered data and information from our archive using a variety of mechanisms ranging from email-based to desktop applications to web applications and web services. Of these, web services have quickly become the primary method for data extraction at the DMC. In 2011, the first full year of operation, web services accounted for over 40% of the data shipped from the DMC. In 2014, over ~450 TB of data was delivered directly to users through web services, representing nearly 70% of all shipments from the DMC that year. In addition to handling requests directly from users, the DMC switched all data extraction methods to use web services in 2014. On average the DMC now handles between 10 and 20 million requests per day submitted to web service interfaces. The rapid adoption of web services is attributed to the many advantages they bring. For users, they provide on-demand data using an interface technology, HTTP, that is widely supported in nearly every computing environment and language. These characteristics, combined with human-readable documentation and existing tools make integration of data access into existing workflows relatively easy. For the DMC, the web services provide an abstraction layer to internal repositories allowing for concentrated optimization of extraction workflow and easier evolution of those repositories. Lending further support to DMC's push in this direction, the core web services for station metadata, timeseries data and event parameters were adopted as standards by the International Federation of Digital Seismograph Networks (FDSN). We expect to continue enhancing existing services and building new capabilities for this platform. For example, the DMC has created a federation system and tools allowing researchers to discover and collect seismic data from data centers running the FDSN-standardized services. A future capability will leverage the DMC's MUSTANG project to select data based on data quality measurements. Within five years, the DMC's web services have proven to be a robust and flexible platform that enables continued growth for the DMC. We expect continued enhancements and adoption of web services.

Microbial Hydrocarbon Co-oxidation

PubMed Central

Raymond, R. L.; Jamison, V. W.; Hudson, J. O.

1967-01-01

Nocardia cultures, isolated from soil by use of n-paraffins as the sole carbon source, have been shown to bring about significant oxidation of several methyl-substituted mono- and dicyclic aromatic hydrocarbons. Oxygen uptake by washed cell suspensions was not a reliable indicator of oxidation. Under co-oxidation conditions in shaken flasks, o- and p-xylenes were oxidized to their respective mono-aromatic acids, o-toluic and p-toluic acids. In addition, a new fermentation product, 2, 3-dihydroxy-p-toluic acid, was found in the p-xylene oxidation system. Of 10 methyl-substituted naphthalenes tested (1-methyl, 2-methyl, 1, 3-dimethyl, 1, 4-dimethyl, 1, 5-dimethyl, 1, 8-dimethyl, 1, 6-dimethyl, 2, 3-dimethyl, 2, 6-dimethyl, 2, 7-dimethyl), only those containing a methyl group in the β position were oxidized at this position to the mono acid. PMID:6049305

Metal chelate process to remove pollutants from fluids

DOEpatents

Chang, Shih-Ger T.

1994-01-01

The present invention relates to improved methods using an organic iron chelate to remove pollutants from fluids, such as flue gas. Specifically, the present invention relates to a process to remove NO.sub.x and optionally SO.sub.2 from a fluid using a metal ion (Fe.sup.2+) chelate wherein the ligand is a dimercapto compound wherein the --SH groups are attached to adjacent carbon atoms (HS--C--C--SH) or (SH--C--CCSH) and contain a polar functional group so that the ligand of DMC chelate is water soluble. Alternatively, the DMC' is covalently attached to a water insoluble substrate such as a polymer or resin, e.g., polystyrene. The chelate is regenerated using electroreduction or a chemical additive. The dimercapto compound bonded to a water insoluble substrate is also useful to lower the concentration or remove hazardous metal ions from an aqueous solution.

Metal chelate process to remove pollutants from fluids

DOEpatents

Chang, S.G.T.

1994-12-06

The present invention relates to improved methods using an organic iron chelate to remove pollutants from fluids, such as flue gas. Specifically, the present invention relates to a process to remove NO[sub x] and optionally SO[sub 2] from a fluid using a metal ion (Fe[sup 2+]) chelate wherein the ligand is a dimercapto compound wherein the --SH groups are attached to adjacent carbon atoms (HS--C--C--SH) or (SH--C--CCSH) and contain a polar functional group so that the ligand of DMC chelate is water soluble. Alternatively, the DMC is covalently attached to a water insoluble substrate such as a polymer or resin, e.g., polystyrene. The chelate is regenerated using electroreduction or a chemical additive. The dimercapto compound bonded to a water insoluble substrate is also useful to lower the concentration or remove hazardous metal ions from an aqueous solution. 26 figures.

Dimethoxy Curcumin Induces Apoptosis by Suppressing Survivin and Inhibits Invasion by Enhancing E-Cadherin in Colon Cancer Cells.

PubMed

Chen, Dong; Dai, Fang; Chen, Zhehang; Wang, Saisai; Cheng, Xiaobin; Sheng, Qinsong; Lin, Jianjiang; Chen, Wenbin

2016-09-11

BACKGROUND Dimethoxy curcumin (DMC) is a kind of lipophilic analog of curcumin with great improvement in chemical and metabolic stability. DMC has been studied in breast and renal cancer, but no research in colon cancer has been found yet. MATERIAL AND METHODS Two colon cancer cells (HT-29 and SW480) and one normal human colon mucosal epithelial cell (NCM460) were used in this study. We studied the effect of DMC on the proliferation in vitro and in vivo. Transwell migration assay was used to estimate the inhibition of DMC on invasion. Moreover, the expressions of PARP, caspase-3, survivin and E-cadherin were detected to uncover the related signaling pathways by western blotting assay both in vitro and in vivo. RESULTS DMC significantly inhibited the growth of colon cancer cells in dose-dependent manner; IC50 for DMC was calculated to be 43.4, 28.2 and 454.8µM on HT-29, SW480 and NCM460. DMC significantly increased the apoptosis in both HT-29 (p=0.0051) and SW480 (p=0.0013) cells in vitro, and significantly suppressed the growth of both cell lines in vivo. Moreover, DMC reduced the number of migrated cells in both HT-29 (p=0.007) and SW480 (p=0.004) cells. By western blotting analysis, the cleavage of pro-caspases-3 and PARP were clearly induced by DMC to their active form, while the expression of survivin was reduced and E-cadherin was enhanced in both cells in vitro and in vivo. CONCLUSIONS DMC may exert an effective anti-tumor effect in colon cancer cells by down-regulating survivin and upregulating E-cadherin.

Mitomycin C and decarbamoyl mitomycin C induce p53-independent p21WAF1/CIP1 activation

PubMed Central

Cheng, Shu-Yuan; Seo, Jiwon; Huang, Bik Tzu; Napolitano, Tanya; Champeil, Elise

2016-01-01

Mitomycin C (MC), a commonly used anticancer drug, induces DNA damage via DNA alkylation. Decarbamoyl mitomycin C (DMC), another mitomycin lacking the carbamate at C10, generates similar lesions as MC. Interstrand cross-links (ICLs) are believed to be the lesions primarily responsible for the cytotoxicity of MC and DMC. The major ICL generated by MC (α-ICL) has a trans stereochemistry at the guanine-drug linkage whereas the major ICL from DMC (β-ICL) has the opposite, cis, stereochemistry. In addition, DMC can provoke strong p53-independent cell death. Our hypothesis is that the stereochemistry of the major unique β-ICL generated by DMC is responsible for this p53-independent cell death signaling. p53 gene is inactively mutated in more than half of human cancers. p21WAF1/CIP1 known as a major effector of p53 is involved in p53-dependent and -independent control of cell proliferation and death. This study revealed the role of p21WAF1/CIP1 on MC and DMC triggered cell damage. MCF-7 (p53-proficient) and K562 (p53-deficient) cells were used. Cell cycle distributions were shifted to the G1/S phase in MCF-7 treated with MC and DMC, but were shifted to the S phase in K562. p21WAF1/CIP1 activation was observed in both cells treated with MC and DMC, and DMC triggered more significant activation. Knocking down p53 in MCF-7 did not attenuate MC and DMC induced p21WAF1/CIP1 activation. The α-ICL itself was enough to cause p21WAF1/CIP1 activation. PMID:27666201

SSTL UK-DMC SLIM-6 data quality assessment

USGS Publications Warehouse

Chander, G.; Saunier, S.; Choate, M.J.; Scaramuzza, P.L.

2009-01-01

Satellite data from the Surrey Satellite Technology Limited (SSTL) United Kingdom (UK) Disaster Monitoring Constellation (DMC) were assessed for geometric and radiometric quality. The UK-DMC Surrey Linear Imager 6 (SLIM-6) sensor has a 32-m spatial resolution and a ground swath width of 640 km. The UK-DMC SLIM-6 design consists of a three-band imager with green, red, and near-infrared bands that are set to similar bandpass as Landsat bands 2, 3, and 4. The UK-DMC data consisted of imagery registered to Landsat orthorectified imagery produced from the GeoCover program. Relief displacements within the UK-DMC SLIM-6 imagery were accounted for by using global 1-km digital elevation models available through the Global Land One-km Base Elevation (GLOBE) Project. Positional accuracy and relative band-to-band accuracy were measured. Positional accuracy of the UK-DMC SLIM-6 imagery was assessed by measuring the imagery against digital orthophoto quadrangles (DOQs), which are designed to meet national map accuracy standards at 1 : 24 000 scales; this corresponds to a horizontal root-mean-square accuracy of about 6 m. The UK-DMC SLIM-6 images were typically registered to within 1.0-1.5 pixels to the DOQ mosaic images. Several radiometric artifacts like striping, coherent noise, and flat detector were discovered and studied. Indications are that the SSTL UK-DMC SLIM-6 data have few artifacts and calibration challenges, and these can be adjusted or corrected via calibration and processing algorithms. The cross-calibration of the UK-DMC SLIM-6 and Landsat 7 Enhanced Thematic Mapper Plus was performed using image statistics derived from large common areas observed by the two sensors.

Celecoxib exerts protective effects in the vascular endothelium via COX-2-independent activation of AMPK-CREB-Nrf2 signalling.

PubMed

Al-Rashed, Fahad; Calay, Damien; Lang, Marie; Thornton, Clare C; Bauer, Andrea; Kiprianos, Allan; Haskard, Dorian O; Seneviratne, Anusha; Boyle, Joseph J; Schönthal, Alex H; Wheeler-Jones, Caroline P; Mason, Justin C

2018-04-19

Although concern remains about the athero-thrombotic risk posed by cyclo-oxygenase (COX)-2-selective inhibitors, recent data implicates rofecoxib, while celecoxib appears equivalent to NSAIDs naproxen and ibuprofen. We investigated the hypothesis that celecoxib activates AMP kinase (AMPK) signalling to enhance vascular endothelial protection. In human arterial and venous endothelial cells (EC), and in contrast to ibuprofen and naproxen, celecoxib induced the protective protein heme oxygenase-1 (HO-1). Celecoxib derivative 2,5-dimethyl-celecoxib (DMC) which lacks COX-2 inhibition also upregulated HO-1, implicating a COX-2-independent mechanism. Celecoxib activated AMPKα (Thr172) and CREB-1 (Ser133) phosphorylation leading to Nrf2 nuclear translocation. Importantly, these responses were not reproduced by ibuprofen or naproxen, while AMPKα silencing abrogated celecoxib-mediated CREB and Nrf2 activation. Moreover, celecoxib induced H-ferritin via the same pathway, and increased HO-1 and H-ferritin in the aortic endothelium of mice fed celecoxib (1000 ppm) or control chow. Functionally, celecoxib inhibited TNF-α-induced NF-κB p65 (Ser536) phosphorylation by activating AMPK. This attenuated VCAM-1 upregulation via induction of HO-1, a response reproduced by DMC but not ibuprofen or naproxen. Similarly, celecoxib prevented IL-1β-mediated induction of IL-6. Celecoxib enhances vascular protection via AMPK-CREB-Nrf2 signalling, a mechanism which may mitigate cardiovascular risk in patients prescribed celecoxib. Understanding NSAID heterogeneity and COX-2-independent signalling will ultimately lead to safer anti-inflammatory drugs.

Spectroscopic Analysis of Temporal Changes in Leaf Moisture and Dry Matter Content

NASA Astrophysics Data System (ADS)

Qi, Y.; Dennison, P. E.; Brewer, S.; Jolly, W. M.; Kropp, R.

2013-12-01

Live fuel moisture (LFM), the ratio of water content to dry matter content (DMC) in live fuel, is critical for determining fire danger and behavior. Remote sensing estimation of LFM often relies on an assumption of changing water content and stable DMC over time. In order to advance understanding of temporal variation in LFM and DMC, we collected field samples and spectroscopic data for two species, lodgepole pine (Pinus contorta) and big sagebrush (Artemisia tridentata), to explore seasonal trends and spectral expression of these trends. New and old needles were measured separately for lodgepole pine. All samples were measured using a visible/NIR/SWIR spectrometer, and coincident samples were processed to provide LFM, DMC, water content and chemical components including structural and non-structural carbohydrates. New needles initially exhibited higher LFM and a smaller proportion of DMC, but differences between new and old needles converged as the new needles hardened. DMC explained more variation in LFM than water content for new pine needles and sagebrush leaves. Old pine needles transported non-structural carbohydrates to new needles to accumulate DMC during the growth season, resulting decreasing LFM in new needles. DMC and water content co-varied with vegetation chemical components and physical structure. Spectral variation in response to changing DMC is difficulty to isolate from the spectral signatures of multiple chemical components. Partial least square regression combined with hyperspectral data may increase modeling performance in LFM estimation.

Airborne measurements of sulfur dioxide, dimethyl sulfide, carbon disulfide, and carbonyl sulfide by isotope dilution gas chromatography/mass spectrometry

NASA Technical Reports Server (NTRS)

Bandy, Alan R.; Thornton, Donald C.; Driedger, Arthur R., III

1993-01-01

A gas chromatograph/mass spectrometer is described for determining atmospheric sulfur dioxide, carbon disulfide, dimethyl sulfide, and carbonyl sulfide from aircraft and ship platforms. Isotopically labelled variants of each analyte were used as internal standards to achieve high precision. The lower limit of detection for each species for an integration time of 3 min was 1 pptv for sulfur dioxide and dimethyl sulfide and 0.2 pptv for carbon disulfide and carbonyl sulfide. All four species were simultaneously determined with a sample frequency of one sample per 6 min or greater. When only one or two species were determined, a frequency of one sample per 4 min was achieved. Because a calibration is included in each sample, no separate calibration sequence was needed. Instrument warmup was only a few minutes. The instrument was very robust in field deployments, requiring little maintenance.

Dmc1 catalyzes interhomolog joint molecule formation in meiosis with Rad51 and Mei5-Sae3 as accessory factors

PubMed Central

Cloud, Veronica; Chan, Yuen-Ling; Grubb, Jennifer; Budke, Brian; Bishop, Douglas K.

2014-01-01

Meiotic recombination in budding yeast requires two RecA-related proteins, Rad51 and Dmc1, both of which form filaments on DNA capable of directing homology search and catalyzing formation of homologous joint molecules (JMs) and strand exchange. Using a separation-of-function mutant form of Rad51, that retains filament-forming but not JM forming activity, we show that the JM activity of Rad51 is fully dispensable for meiotic recombination. The corresponding mutation in Dmc1 causes a profound recombination defect, demonstrating Dmc1’s JM activity alone is responsible for meiotic recombination. We further provide biochemical evidence that Rad51 acts with Mei5-Sae3 as a Dmc1 accessory factor. Thus, Rad51 is a multifunctional protein that catalyzes recombination directly in mitosis and indirectly, via Dmc1, during meiosis. PMID:22955832

Rad51 is an accessory factor for Dmc1-mediated joint molecule formation during meiosis.

PubMed

Cloud, Veronica; Chan, Yuen-Ling; Grubb, Jennifer; Budke, Brian; Bishop, Douglas K

2012-09-07

Meiotic recombination in budding yeast requires two RecA-related proteins, Rad51 and Dmc1, both of which form filaments on DNA capable of directing homology search and catalyzing formation of homologous joint molecules (JMs) and strand exchange. With use of a separation-of-function mutant form of Rad51 that retains filament-forming but not JM-forming activity, we show that the JM activity of Rad51 is fully dispensable for meiotic recombination. The corresponding mutation in Dmc1 causes a profound recombination defect, demonstrating Dmc1's JM activity alone is responsible for meiotic recombination. We further provide biochemical evidence that Rad51 acts with Mei5-Sae3 as a Dmc1 accessory factor. Thus, Rad51 is a multifunctional protein that catalyzes recombination directly in mitosis and indirectly, via Dmc1, during meiosis.

Tolerance of DNA Mismatches in Dmc1 Recombinase-mediated DNA Strand Exchange.

PubMed

Borgogno, María V; Monti, Mariela R; Zhao, Weixing; Sung, Patrick; Argaraña, Carlos E; Pezza, Roberto J

2016-03-04

Recombination between homologous chromosomes is required for the faithful meiotic segregation of chromosomes and leads to the generation of genetic diversity. The conserved meiosis-specific Dmc1 recombinase catalyzes homologous recombination triggered by DNA double strand breaks through the exchange of parental DNA sequences. Although providing an efficient rate of DNA strand exchange between polymorphic alleles, Dmc1 must also guard against recombination between divergent sequences. How DNA mismatches affect Dmc1-mediated DNA strand exchange is not understood. We have used fluorescence resonance energy transfer to study the mechanism of Dmc1-mediated strand exchange between DNA oligonucleotides with different degrees of heterology. The efficiency of strand exchange is highly sensitive to the location, type, and distribution of mismatches. Mismatches near the 3' end of the initiating DNA strand have a small effect, whereas most mismatches near the 5' end impede strand exchange dramatically. The Hop2-Mnd1 protein complex stimulates Dmc1-catalyzed strand exchange on homologous DNA or containing a single mismatch. We observed that Dmc1 can reject divergent DNA sequences while bypassing a few mismatches in the DNA sequence. Our findings have important implications in understanding meiotic recombination. First, Dmc1 acts as an initial barrier for heterologous recombination, with the mismatch repair system providing a second level of proofreading, to ensure that ectopic sequences are not recombined. Second, Dmc1 stepping over infrequent mismatches is likely critical for allowing recombination between the polymorphic sequences of homologous chromosomes, thus contributing to gene conversion and genetic diversity. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

Tolerance of DNA Mismatches in Dmc1 Recombinase-mediated DNA Strand Exchange*

PubMed Central

Borgogno, María V.; Monti, Mariela R.; Zhao, Weixing; Sung, Patrick; Argaraña, Carlos E.; Pezza, Roberto J.

2016-01-01

Recombination between homologous chromosomes is required for the faithful meiotic segregation of chromosomes and leads to the generation of genetic diversity. The conserved meiosis-specific Dmc1 recombinase catalyzes homologous recombination triggered by DNA double strand breaks through the exchange of parental DNA sequences. Although providing an efficient rate of DNA strand exchange between polymorphic alleles, Dmc1 must also guard against recombination between divergent sequences. How DNA mismatches affect Dmc1-mediated DNA strand exchange is not understood. We have used fluorescence resonance energy transfer to study the mechanism of Dmc1-mediated strand exchange between DNA oligonucleotides with different degrees of heterology. The efficiency of strand exchange is highly sensitive to the location, type, and distribution of mismatches. Mismatches near the 3′ end of the initiating DNA strand have a small effect, whereas most mismatches near the 5′ end impede strand exchange dramatically. The Hop2-Mnd1 protein complex stimulates Dmc1-catalyzed strand exchange on homologous DNA or containing a single mismatch. We observed that Dmc1 can reject divergent DNA sequences while bypassing a few mismatches in the DNA sequence. Our findings have important implications in understanding meiotic recombination. First, Dmc1 acts as an initial barrier for heterologous recombination, with the mismatch repair system providing a second level of proofreading, to ensure that ectopic sequences are not recombined. Second, Dmc1 stepping over infrequent mismatches is likely critical for allowing recombination between the polymorphic sequences of homologous chromosomes, thus contributing to gene conversion and genetic diversity. PMID:26709229

Quantitative trait loci controlling cyanogenic glucoside and dry matter content in cassava (Manihot esculenta Crantz) roots.

PubMed

Balyejusa Kizito, Elizabeth; Rönnberg-Wästljung, Ann-Christin; Egwang, Thomas; Gullberg, Urban; Fregene, Martin; Westerbergh, Anna

2007-09-01

Cassava (Manihot esculenta Crantz) is a starchy root crop grown in the tropics mainly by small-scale farmers even though agro-industrial processing is rapidly increasing. For this processing market improved varieties with high dry matter root content (DMC) is required. Potentially toxic cyanogenic glucosides are synthesized in the leaves and translocated to the roots. Selection for varieties with low cyanogenic glucoside potential (CNP) and high DMC is among the principal objectives in cassava breeding programs. However, these traits are highly influenced by the environmental conditions and the genetic control of these traits is not well understood. An S(1) population derived from a cross between two bred cassava varieties (MCOL 1684 and Rayong 1) that differ in CNP and DMC was used to study the heritability and genetic basis of these traits. A broad-sense heritability of 0.43 and 0.42 was found for CNP and DMC, respectively. The moderate heritabilities for DMC and CNP indicate that the phenotypic variation of these traits is explained by a genetic component. We found two quantitative trait loci (QTL) on two different linkage groups controlling CNP and six QTL on four different linkage groups controlling DMC. One QTL for CNP and one QTL for DMC mapped near each other, suggesting pleiotrophy and/or linkage of QTL. The two QTL for CNP showed additive effects while the six QTL for DMC showed additive effect, dominance or overdominance. This study is a first step towards developing molecular marker tools for efficient breeding of CNP and DMC in cassava.

Construction and development of IGP DMC of China National Seismological Network

NASA Astrophysics Data System (ADS)

Zheng, X.; Zheng, J.; Lin, P.; Yao, Z.; Liang, J.

2011-12-01

In 2003, CEA (China Earthquake Administration) commenced the construction of China Digital Seismological Observation Network. By the end of 2007, a new-generation digital seismological observation system had been established, which consists of 1 National Seismic Network, 32 regional seismic networks, 2 small-aperture seismic arrays, 6 volcano monitoring networks and 19 mobile seismic networks, as well as CENC (China Earthquake Network Center) DMC (Data Management Centre) and IGP (Institute of Geophysics) DMC. Since then, the seismological observation system of China has completely entered a digital time. For operational, data backup and data security considerations, the DMC at the Institute of Geophysics (IGP), CEA was established at the end of 2007. IGP DMC now receives and archives waveform data from more than 1000 permanent seismic stations around China in real-time. After the great Wenchuan and Yushu earthquakes, the real-time waveform data from 56 and 8 portable seismic stations deployed in the aftershock area are added to IGP DMC. The technical system of IGP DMC is designed to conduct data management, processing and service through the network of CEA. We developed and integrated a hardware system with high-performance servers, large-capacity disc arrays, tape library and other facilities, as well as software packages for real-time waveform data receiving, storage, quality control, processing and service. Considering the demands from researchers for large quantities of seismic event waveform data, IGP DMC adopts an innovative "user order" method to extract event waveform data. Users can specify seismic stations, epicenter distance and record length. In a short period of 3 years, IGP DMC has supplied about 350 Terabytes waveform data to over 200 researches of more than 40 academic institutions. According to incomplete statistics, over 40 papers have been published in professional journals, in which 30 papers were indexed by SCI. Now, IGP DMC has become an important platform of promoting seismological researches in China. In the future, IGP DMC will continue to improve its technical system with powerful ability of waveform data processing, management and service, and to provide better and more data service to the research community. We expect IGP DMC to become an exchange and collaboration platform for geo-scientific researchers around the world.

Diffusion quantum Monte Carlo and density functional calculations of the structural stability of bilayer arsenene

NASA Astrophysics Data System (ADS)

Kadioglu, Yelda; Santana, Juan A.; Özaydin, H. Duygu; Ersan, Fatih; Aktürk, O. Üzengi; Aktürk, Ethem; Reboredo, Fernando A.

2018-06-01

We have studied the structural stability of monolayer and bilayer arsenene (As) in the buckled (b) and washboard (w) phases with diffusion quantum Monte Carlo (DMC) and density functional theory (DFT) calculations. DMC yields cohesive energies of 2.826(2) eV/atom for monolayer b-As and 2.792(3) eV/atom for w-As. In the case of bilayer As, DMC and DFT predict that AA-stacking is the more stable form of b-As, while AB is the most stable form of w-As. The DMC layer-layer binding energies for b-As-AA and w-As-AB are 30(1) and 53(1) meV/atom, respectively. The interlayer separations were estimated with DMC at 3.521(1) Å for b-As-AA and 3.145(1) Å for w-As-AB. A comparison of DMC and DFT results shows that the van der Waals density functional method yields energetic properties of arsenene close to DMC, while the DFT + D3 method closely reproduced the geometric properties from DMC. The electronic properties of monolayer and bilayer arsenene were explored with various DFT methods. The bandgap values vary significantly with the DFT method, but the results are generally qualitatively consistent. We expect the present work to be useful for future experiments attempting to prepare multilayer arsenene and for further development of DFT methods for weakly bonded systems.

Demethoxycurcumin, a Natural Derivative of Curcumin Abrogates Rotenone-induced Dopamine Depletion and Motor Deficits by Its Antioxidative and Anti-inflammatory Properties in Parkinsonian Rats

PubMed Central

Ramkumar, Muthu; Rajasankar, Srinivasagam; Gobi, Veerapan Venkatesh; Janakiraman, Udaiyappan; Manivasagam, Thamilarasan; Thenmozhi, Arokiasamy Justin; Essa, Musthafa Mohamed; Chidambaram, Ranganathan; Chidambaram, Saravana Babu; Guillemin, Giles J.

2018-01-01

Background: Parkinson's disease (PD) is a progressive neurodegenerative disorder (NDD) associated with the loss of dopaminergic neurons in the substantia nigra and subsequently has an effect on motor function and coordination. The pathology of PD is multifactorial, in which neuroinflammation and oxidative damage are the two of the main protagonists. Objectives: The present study aims to assess the potential antioxidant and anti-inflammatory effects of demethoxycurcumin (DMC), a natural derivative of curcumin, against rotenone-induced PD in rats. Materials and Methods: Rats were randomized and divided into six groups: control, rotenone (0.5 mg/kg/day, intraperitoneal in sunflower oil) treated for 7 days, rotenone and DMC (5, 10, and 20 mg/kg b.w) cotreated, and DMC (20 mg/kg b.w) alone treated groups. Results: Based on the dopamine concentration and biochemical estimations, the effective dose of DMC was selected and the chronic study was performed. At the end of the experimental period, behavioral studies and protein expression patterns of inflammatory markers were analyzed. Rotenone treatment led to motor dysfunctions, neurochemical deficits, and oxidative stress and enhanced expressions of inflammatory markers, whereas oral administration of DMC attenuated all the above. Conclusion: Even though further research is needed to prove its efficacy in clinical trial, the results of our study showed that DMC may offer a promising and new therapeutic lead for the treatment of NDDs including PD. SUMMARY Curcumin and their derivatives have been shown to be potent neuroprotective effectDemethoxycurcumin (DMC) amolerated the rotenone induced behavioural alterationsDMC abrogated the rotenone induced dopamine deficitsDMC attenuated the rotenone induced oxidative stressDMC diminished the rotenone mediated inflammation. Abbreviations used: COX-2: Cyclooxygenase-2; DA: Dopamine; DMC: Demethoxycurcumin; DMRT: Duncan's multiple range test; GSH: Reduced glutathione; GPx: Glutathione peroxidase; IL-1 β: Interleukin-1 β; IL-6: Interleukin-6; iNOS: Inducible nitric oxide synthase; PD: Parkinson's disease; SN: Substantia nigra; SOD: Superoxide dismutase; TBARS: Thiobarbituric acid reactive substances; TNF-α: Tumor necrosis factor-α. PMID:29576695

Electrochemical and impedance investigation of the effect of lithium malonate on the performance of natural graphite electrodes in lithium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Xiao-Guang; Dai, Sheng

2010-01-01

Lithium malonate (LM) was coated on the surface of a natural graphite (NG) electrode, which was then tested as the negative electrode in the electrolytes of 0.9 M LiPF6/EC-PC-DMC (1/1/3, by weight) and 1.0 M LiBF4/EC-PC-DMC (1/1/3, by weight) under a current density of 0.075 mA cm-2. LM was also used as an additive to the electrolyte of 1.0 M LiPF6/EC-DMC-DEC (1/1/1, by volume) and tested on a bare graphite electrode. It was found that both the surface coating and the additive approach were effective in improving first charge discharge capacity and coulomb efficiency. Electrochemical impedance spectra showed that themore » decreased interfacial impedance was coupled with improved coulomb efficiency of the cells using coated graphite electrodes. Cyclic voltammograms (CVs) on fresh bare and coated natural graphite electrodes confirmed that all the improvement in the half-cell performance was due to the suppression of the solvent decomposition through the surface modification with LM. The CV data also showed that the carbonate electrolyte with LM as the additive was not stable against oxidation, which resulted in lower capacity of the full cell with commercial graphite and LiCoO2 electrodes.« less

Abiotic synthesis of organic compounds from carbon disulfide under hydrothermal conditions.

PubMed

Rushdi, Ahmed I; Simoneit, Bernd R T

2005-12-01

Abiotic formation of organic compounds under hydrothermal conditions is of interest to bio, geo-, and cosmochemists. Oceanic sulfur-rich hydrothermal systems have been proposed as settings for the abiotic synthesis of organic compounds. Carbon disulfide is a common component of magmatic and hot spring gases, and is present in marine and terrestrial hydrothermal systems. Thus, its reactivity should be considered as another carbon source in addition to carbon dioxide in reductive aqueous thermosynthesis. We have examined the formation of organic compounds in aqueous solutions of carbon disulfide and oxalic acid at 175 degrees C for 5 and 72 h. The synthesis products from carbon disulfide in acidic aqueous solutions yielded a series of organic sulfur compounds. The major compounds after 5 h of reaction included dimethyl polysulfides (54.5%), methyl perthioacetate (27.6%), dimethyl trithiocarbonate (6.8%), trithianes (2.7%), hexathiepane (1.4%), trithiolanes (0.8%), and trithiacycloheptanes (0.3%). The main compounds after 72 h of reaction consisted of trithiacycloheptanes (39.4%), pentathiepane (11.6%), tetrathiocyclooctanes (11.5%), trithiolanes (10.6%), tetrathianes (4.4%), trithianes (1.2%), dimethyl trisulfide (1.1%), and numerous minor compounds. It is concluded that the abiotic formation of aliphatic straight-chain and cyclic polysulfides is possible under hydrothermal conditions and warrants further studies.

Capacity in vacuo: an audit of decision-making capacity assessments in a liaison psychiatry service

PubMed Central

Spencer, Benjamin W. J.; Wilson, Gareth; Okon-Rocha, Ewa; Owen, Gareth S.; Wilson Jones, Charlotte

2017-01-01

Aims and method We aimed to audit the documentation of decision-making capacity (DMC) assessments by our liaison psychiatry service against the legal criteria set out in the Mental Capacity Act 2005. We audited 3 months split over a 2-year period occurring before, during and after an educational intervention to staff. Results There were 21 assessments of DMC in month 1 (6.9% of all referrals), 27 (9.7%) in month 16, and 24 (6.6%) in month 21. Only during the intervention (month 16) did any meet our gold-standard (n = 2). Severity of consequences of the decision (odds ratio (OR) 24.4) and not agreeing to the intervention (OR = 21.8) were highly likely to result in lacking DMC. Clinical implications Our audit demonstrated that DMC assessments were infrequent and poorly documented, with no effect of our legally focused educational intervention demonstrated. Our findings of factors associated with the outcome of the assessment of DMC confirm the anecdotal beliefs in this area. Clinicians and service leads need to carefully consider how to make the legal model of DMC more meaningful to clinicians when striving to improve documentation of DMC assessments. PMID:28184310

Capacity in vacuo: an audit of decision-making capacity assessments in a liaison psychiatry service.

PubMed

Spencer, Benjamin W J; Wilson, Gareth; Okon-Rocha, Ewa; Owen, Gareth S; Wilson Jones, Charlotte

2017-02-01

Aims and method We aimed to audit the documentation of decision-making capacity (DMC) assessments by our liaison psychiatry service against the legal criteria set out in the Mental Capacity Act 2005. We audited 3 months split over a 2-year period occurring before, during and after an educational intervention to staff. Results There were 21 assessments of DMC in month 1 (6.9% of all referrals), 27 (9.7%) in month 16, and 24 (6.6%) in month 21. Only during the intervention (month 16) did any meet our gold-standard ( n = 2). Severity of consequences of the decision (odds ratio (OR) 24.4) and not agreeing to the intervention (OR = 21.8) were highly likely to result in lacking DMC. Clinical implications Our audit demonstrated that DMC assessments were infrequent and poorly documented, with no effect of our legally focused educational intervention demonstrated. Our findings of factors associated with the outcome of the assessment of DMC confirm the anecdotal beliefs in this area. Clinicians and service leads need to carefully consider how to make the legal model of DMC more meaningful to clinicians when striving to improve documentation of DMC assessments.

Selective effect of 2',6'-dihydroxy-4'-methoxychalcone isolated from Piper aduncum on Leishmania amazonensis.

PubMed

Torres-Santos, E C; Moreira, D L; Kaplan, M A; Meirelles, M N; Rossi-Bergmann, B

1999-05-01

2',6'-Dihydroxy-4'-methoxychalcone (DMC) was purified from the dichloromethane extract of Piper aduncum inflorescences. DMC showed significant activity in vitro against promastigotes and intracellular amastigotes of Leishmania amazonensis, with 50% effective doses of 0.5 and 24 micrograms/ml, respectively. Its inhibitory effect on amastigotes is apparently a direct effect on the parasites and is not due to activation of the nitrogen oxidative metabolism of macrophages, since the production of nitric oxide by both unstimulated and recombinant gamma interferon-stimulated macrophages was decreased rather than increased with DMC. The phagocytic activity of macrophages was functioning normally even with DMC concentrations as high as 80 micrograms/ml, as seen by electron microscopy and by the uptake of fluorescein isothiocyanate-labeled beads. Ultrastructural studies also showed that in the presence of DMC the mitochondria of promastigotes were enlarged and disorganized. Despite destruction of intracellular amastigotes, no disarrangement of macrophage organelles were observed, even at 80 micrograms of DMC/ml. These observations suggest that DMC is selectively toxic to the parasites. Its simple structure may well enable it to serve as a new lead compound for the synthesis of novel antileishmanial drugs.

X-Ray Absorption Spectroscopy of Electrochemically Generated Species

DTIC Science & Technology

1989-01-27

constructed from gold minigrid, colloidal graphite, and reticulated vitreous carbon (RVC). The use of gold minigrid electrodes has been demonstrated for...jBF n (bipy= 2,2’-ipyridine, dmp= 2,9-dimethvl- 1,10-phenanthroline) in solution at reticulated vitreous carbon electrodes, and incorporated in...Fe(bipy)3(C104)2, Ru(bipy)3Cl2, and Cu(drp)2BF4 (bipy= 2,2’-bipyridine, dmp= 2, 9-dimethyl-l,10-phenanthroline) in solution at reticulated vitreous

p53 Protein interacts specifically with the meiosis-specific mammalian RecA-like protein DMC1 in meiosis.

PubMed

Habu, Toshiyuki; Wakabayashi, Nobunao; Yoshida, Kayo; Yomogida, Kenntaro; Nishimune, Yoshitake; Morita, Takashi

2004-06-01

The tumor suppressor protein p53 is specifically expressed during meiosis in spermatocytes. Subsets of p53 knockout mice exhibit testicular giant cell degenerative syndrome, which suggests p53 may be associated with meiotic cell cycle and/or DNA metabolism. Here, we show that p53 binds to the mouse meiosis-specific RecA-like protein Mus musculus DMC1 (MmDMC1). The C-terminal domain (amino acid 234-340) of MmDMC1 binds to DNA-binding domain of p53 protein. p53 might be involved in homologous recombination and/or checkpoint function by directly binding to DMC1 protein to repress genomic instability in meiotic germ cells.

Decision-making capacity for treatment in psychiatric and medical in-patients: cross-sectional, comparative study†

PubMed Central

Owen, Gareth S.; Szmukler, George; Richardson, Genevra; David, Anthony S.; Raymont, Vanessa; Freyenhagen, Fabian; Martin, Wayne; Hotopf, Matthew

2013-01-01

Background Is the nature of decision-making capacity (DMC) for treatment significantly different in medical and psychiatric patients? Aims To compare the abilities relevant to DMC for treatment in medical and psychiatric patients who are able to communicate a treatment choice. Method A secondary analysis of two cross-sectional studies of consecutive admissions: 125 to a psychiatric hospital and 164 to a medical hospital. The MacArthur Competence Assessment Tool - Treatment and a clinical interview were used to assess decision-making abilities (understanding, appreciating and reasoning) and judgements of DMC. We limited analysis to patients able to express a choice about treatment and stratified the analysis by low and high understanding ability. Results Most people scoring low on understanding were judged to lack DMC and there was no difference by hospital (P = 0.14). In both hospitals there were patients who were able to understand yet lacked DMC (39% psychiatric v. 13% medical in-patients, P<0.001). Appreciation was a better ‘test’ of DMC in the psychiatric hospital (where psychotic and severe affective disorders predominated) (P<0.001), whereas reasoning was a better test of DMC in the medical hospital (where cognitive impairment was common) (P = 0.02). Conclusions Among those with good understanding, the appreciation ability had more salience to DMC for treatment in a psychiatric setting and the reasoning ability had more salience in a medical setting. PMID:23969482

Production of biodiesel from Coelastrella sp. microalgae

NASA Astrophysics Data System (ADS)

Mansur, Dieni; Fitriady, Muhammad Arifuddin; Susilaningsih, Dwi; Simanungkalit, Sabar Pangihutan

2017-11-01

Microalgae have a wide area of usage and one of them it can be used for biodiesel production. In biodiesel production, lipids containing triglyceride or free fatty acid are converted into methyl ester through trans/esterification reactions. Lipids from microalgae can be extracted by acetone and dimethyl carbonate using homogenizer. Esterification of the lipids was investigated using various catalysts and source of methyl group. Activity of homogeneous catalyst such as HCl and H2SO4 and heterogeneous catalysts such as montmorillonit K-10 and ledgestone was investigated. Moreover, methanol and dimethyl carbonate as source of methyl group were also studied. Among of catalysts with methanol as source of methyl group, it was found that yield of crude biodiesel derived from Choelestrella Sp. microalgae was high over H2SO4 catalyst. On the other hand, over H2SO4 catalyst using dimethyl carbonate as source of methyl group, yield of crude biodiesel significant increase. However, FAME composition of crude biodiesel was high over HCl catalyst.

Demographics.

PubMed

Gillis, Artha J; Bath, Eraka

2016-01-01

There is a large proportion of minority youth involved in the juvenile justice system. Disproportionate minority contact (DMC) occurs when the proportion of any ethnic group is higher at any given stage in the juvenile justice process than the proportion of this group in the general population. There are several theories explaining the presence and persistence of DMC. This article reviews the history of DMC and the theories and implications of this problem. It discusses several targets for interventions designed to reduce DMC and offer resources in this area. Copyright © 2016 Elsevier Inc. All rights reserved.

A Novel Battery Cathode Material Based on intercalation Chemistry: Redox Reactions of the 2,5-Dimercapto-1,3,4-Thiadiazole/V2O5 Xerogel System

DTIC Science & Technology

1998-06-29

of some interstitial water during intercalation of the disulfide polymer of DMcT. Elemental analysis gives a composition for the intercalation...the disulfide polymer of DMcT. Elemental analysis gives a composition for the intercalation material of [(polyDMcT)o25*V205𔃻.4H20]. The cyclic...13.5 A). This change is consistent with loss of some interstitial water during intercalation of the disulfide polymer of DMcT. Elemental analysis

Selective Effect of 2′,6′-Dihydroxy-4′-Methoxychalcone Isolated from Piper aduncum on Leishmania amazonensis

PubMed Central

Torres-Santos, Eduardo Caio; Moreira, Davyson Lima; Kaplan, Maria Auxiliadora C.; Meirelles, Maria Nazareth; Rossi-Bergmann, Bartira

1999-01-01

2′,6′-Dihydroxy-4′-methoxychalcone (DMC) was purified from the dichloromethane extract of Piper aduncum inflorescences. DMC showed significant activity in vitro against promastigotes and intracellular amastigotes of Leishmania amazonensis, with 50% effective doses of 0.5 and 24 μg/ml, respectively. Its inhibitory effect on amastigotes is apparently a direct effect on the parasites and is not due to activation of the nitrogen oxidative metabolism of macrophages, since the production of nitric oxide by both unstimulated and recombinant gamma interferon-stimulated macrophages was decreased rather than increased with DMC. The phagocytic activity of macrophages was functioning normally even with DMC concentrations as high as 80 μg/ml, as seen by electron microscopy and by the uptake of fluorescein isothiocyanate-labeled beads. Ultrastructural studies also showed that in the presence of DMC the mitochondria of promastigotes were enlarged and disorganized. Despite destruction of intracellular amastigotes, no disarrangement of macrophage organelles were observed, even at 80 μg of DMC/ml. These observations suggest that DMC is selectively toxic to the parasites. Its simple structure may well enable it to serve as a new lead compound for the synthesis of novel antileishmanial drugs. PMID:10223942

Protective effect of the daming capsule on impaired baroreflexes in STZ-induced diabetic rats with hyperlipoidemia.

PubMed

Ai, Jing; Wang, Li-Hong; Zhang, Rong; Qiao, Guo-Fen; Wang, Ning; Sun, Li-Hua; Lu, Guan-Yi; Sun, Chao; Yang, Bao-Feng

2010-12-22

The Daming capsule (DMC) is a traditional Chinese medicine used to treat hyperlipoidemia. Both clinic trials and studies on animal models have demonstrated that DMC is beneficial against diabetic symptoms. Impairment of the baroreflex can cause life-threatening arrhythmias and sudden cardiac death in patients with diabetes mellitus (DM). This study was designed to elucidate the effects of DMC on baroreflexes in streptozocin (STZ)-induced diabetic rats with hyperlipoidemia. Wistar rats were randomly divided into three groups: untreated controls, rats pretreated STZ and high lipids (a diabetes model or DM rats), and DM rats treated with DMC. The baroreflex sensitivity was examined during intravenous injection of phenylephrine (PE) or sodium nitroprusside (SNP) and quantified by the change in heart rate over the change in mean arterial blood pressure (ΔHR/ΔMABP). Morphological remodeling of baroreceptors was analyzed by transmission electron microscopy (TEM). The mRNA levels and expression of GluR2 and a GABAA receptor subunit were measured by quantitative RT-PCR and Western blotting. Compared to untreated DM rats, DMC significantly elevated the ratio of ΔHR/ΔMABP by enhancing the compensatory reduction in HR (-ΔHR) in response to PE-induced hypertension (+ΔMABP) (P < 0.05). In the presence of SNP, DMC increased the ΔMABP (P < 0.05). In addition, DMC markedly shortened the duration of blood pressure changes elicited by PE or SNP in DM rats compared to the untreated DM group (P < 0.05). Electron microscopy revealed disrupted myelin sheaths, swollen ER, and lysed mitochondria in the nucleus ambiguous (NAm) DM rats. These signs of neuropathology were largely prevented by treatment with DMC for 30 days. Treatment with DMC elevated both mRNA and protein level of GluR2 in the NAm of DM rats, but had no effect on GABAA receptor expression. The Daming capsule partially reversed the parasympathetic baroreflex impairment observed in STZ-induced diabetic rats with hyperlipoidemia. Treatment with DMC also prevented the degeneration of neurons and myelinated axons in the brain stem NAm and reversed the down-regulation of GluR2 mRNA. Rescue of NAm function may contribute to the medicinal properties of DMC in diabetic rats.

Biochemical Connections Between the Atmosphere and the Ocean

NASA Astrophysics Data System (ADS)

Liss, P. S.

INTRODUCTION THE CHEMICAL COMPOSITION OF THE EARTH'S ATMOSPHERE AIR-SEA EXCHANGE OF GASES OF IMPORTANCE Ozone Manmade Carbon Dioxide Dimethyl Sulphide Dimethyl Selenide Ammonia IMPACT OF ATMOSPHERIC DUST ON OCEAN BIOCHEMISTRY GLOBAL PERSPECTIVES ON BIOGEOCHEMICAL FLUXES ACROSS THE AIR-SEA INTERFACE DMS and the CLAW Hypothesis Iron REFERENCES

77 FR 50613 - Didecyl Dimethyl Ammonium Carbonate and Didecyl Dimethyl Ammonium Bicarbonate; Exemption From the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-22

... used as sanitizers on appliances, beverage bottling, counter tops, food packaging, refrigerators..., countertops, and in food/beverage processing facilities. The assessment calculated the Daily Dietary Dose (DDD... estimates from exposure to treated food packaging and beverage bottles are also below the Agency's LOC...

Latent Heat Characteristics of Biobased Oleochemical Carbonates as Novel Phase Change Materials

USDA-ARS?s Scientific Manuscript database

Oleochemical carbonates are biobased materials that were readily prepared through a carbonate interchange reaction between renewable C10-C18 fatty alcohols and dimethyl or diethyl carbonate in the presence of a catalyst. These carbonates have various commercial uses in cosmetic, fuel additive and l...

EPR studies of free radicals in A-2058 human melanoma cells treated by valproic acid and 5,7-dimethoxycoumarin.

PubMed

Zdybel, Magdalena; Chodurek, Ewa; Pilawa, Barbara

2014-01-01

Free radicals in A-2058 human melanoma cells were studied by the use of electron paramagnetic resonance (EPR) spectroscopy. The aim of this work was to determine the changes in relative free radical concentrations in tumor A-2058 cells after treatment by valproic acid (VPA) and 5,7-dimethoxycoumarin (DMC). The influences of VPA and DMC on free radicals in A-2058 cells were compared with those for human melanoma malignum A-375 and G-361 cells, which were tested by us earlier. Human malignant melanoma A-2058 cells were exposed to interactions with VPA, DMC, and both VPA and DMC. The tumor cells A-2058 were purchased from LGC Standards (Lomianki, Poland), and they were grown in the standard conditions: at 37°C and in an atmosphere containing 95% air and 5% CO2, in the Minimum Essential Medium Eagle (MEM, Sigma-Aldrich). The A-2058 cells were incubated with VPA (1 mM) and DMC (10 μM) for 4 days. The first-derivative EPR spectra of the control A-2058 cells, and the cells treated with VPA, DMC, and both VPA and DMC, were measured by the electron paramagnetic resonance spectrometer of Radiopan (Poznań, Poland) with microwaves from an X-band (9.3 GHz). The parameters of the EPR lines: amplitudes (A), integral intensities (I), line widths (ΔBpp), and g-factors, were analyzed. The changes of amplitudes and line widths with microwave power increasing from 2.2 to 70 mW were drawn evaluated, o-Semiquinone free radicals of melanin biopolymer are mainly responsible for the EPR lines of A-2058 melanoma malignum cells. The amounts of free radicals in A-2058 cells treated with VPA, and both VPA and DMC, were lower than in the untreated control cells. Application of the tested substances (VPA, and both VPA and DMC) as the antitumor compounds was discussed. DMC without VPA did not decrease free radicals concentration in A-2058 cells. The studies con-firmed that EPR spectroscopy may be used to examine interactions of free radicals with antitumor compounds.

Altered sterol profile induced in Leishmania amazonensis by a natural dihydroxymethoxylated chalcone

PubMed Central

Torres-Santos, Eduardo Caio; Sampaio-Santos, Maria Isabel; Buckner, Frederick S.; Yokoyama, Kohei; Gelb, Michael; Urbina, Julio A.; Rossi-Bergmann, Bartira

2009-01-01

Objectives The effects of the antileishmanial chalcone 2′,6′-dihydroxy-4′-methoxychalcone (DMC) on Leishmania amazonensis sterol composition and biosynthesis were investigated to obtain information about the mechanism of growth inhibition by DMC on this parasite. Methods The interference of sterol biosynthesis by DMC was studied in drug-treated promastigotes by two different methods. (i) Newly synthesized sterols from parasites grown in the presence of [3H]mevalonate were analysed by thin layer chromatography (TLC)/fluorography. (ii) Total sterols extracted from the parasites grown with or without DMC were characterized by gas chromatography coupled to mass spectroscopy (GC/MS). Results TLC and GC/MS analyses of sterols extracted from DMC-treated promastigotes revealed the accumulation of early precursors and a reduction in the levels of C-14 demethylated and C-24 alkylated sterols, as well as a reduction in exogenous cholesterol uptake. Conclusions This study demonstrates that the natural chalcone DMC alters the sterol composition of L. amazonensis and suggests that the parasite target is different from other known sterol inhibitors. PMID:19176591

Enhanced Cognitive Effects of Demethoxycurcumin, a Natural Derivative of Curcumin on Scopolamine-Induced Memory Impairment in Mice.

PubMed

Lim, Dong Wook; Son, Hyun Jung; Um, Min Young; Kim, In-Ho; Han, Daeseok; Cho, Suengmok; Lee, Chang-Ho

2016-08-05

In the present study, we examined the ameliorating effects of demethoxycurcumin (DMC) on memory impairment induced by scopolamine using passive avoidance and Morris water maze tests in mice. Moreover, to determine the neurobiological effects underlying the ameliorating effects of the DMC, choline acetyltransferase (ChAT) immunoreactivity was evaluated in mice exposed to scopolamine. Our results demonstrated that chronic oral administration (28 days) of DMC (10 mg/kg) improved scopolamine-induced learning impairment in the passive avoidance task and memory impairment in the Morris water maze. Moreover, Choline acetyltransferase (ChAT) activity in the DMC-treated group was significantly increased to 33.03% compared with the control group. Our present finding suggests that DMC ameliorates memory impairments induced by scopolamine treatment through reversing the reduction of hippocampal ChAT expression in mice.

CMOS Imaging Sensor Technology for Aerial Mapping Cameras

NASA Astrophysics Data System (ADS)

Neumann, Klaus; Welzenbach, Martin; Timm, Martin

2016-06-01

In June 2015 Leica Geosystems launched the first large format aerial mapping camera using CMOS sensor technology, the Leica DMC III. This paper describes the motivation to change from CCD sensor technology to CMOS for the development of this new aerial mapping camera. In 2002 the DMC first generation was developed by Z/I Imaging. It was the first large format digital frame sensor designed for mapping applications. In 2009 Z/I Imaging designed the DMC II which was the first digital aerial mapping camera using a single ultra large CCD sensor to avoid stitching of smaller CCDs. The DMC III is now the third generation of large format frame sensor developed by Z/I Imaging and Leica Geosystems for the DMC camera family. It is an evolution of the DMC II using the same system design with one large monolithic PAN sensor and four multi spectral camera heads for R,G, B and NIR. For the first time a 391 Megapixel large CMOS sensor had been used as PAN chromatic sensor, which is an industry record. Along with CMOS technology goes a range of technical benefits. The dynamic range of the CMOS sensor is approx. twice the range of a comparable CCD sensor and the signal to noise ratio is significantly better than with CCDs. Finally results from the first DMC III customer installations and test flights will be presented and compared with other CCD based aerial sensors.

Neuroprotective effect of Demethoxycurcumin, a natural derivative of Curcumin on rotenone induced neurotoxicity in SH-SY 5Y Neuroblastoma cells.

PubMed

Ramkumar, Muthu; Rajasankar, Srinivasagam; Gobi, Veerappan Venkatesh; Dhanalakshmi, Chinnasamy; Manivasagam, Thamilarasan; Justin Thenmozhi, Arokiasamy; Essa, Musthafa Mohamed; Kalandar, Ameer; Chidambaram, Ranganathan

2017-04-18

Mitochondrial dysfunction and oxidative stress are the main toxic events leading to dopaminergic neuronal death in Parkinson's disease (PD) and identified as vital objective for therapeutic intercession. This study investigated the neuro-protective effects of the demethoxycurcumin (DMC), a derivative of curcumin against rotenone induced neurotoxicity. SH-SY5Y neuroblastoma cells are divided into four experimental groups: untreated cells, cells incubated with rotenone (100 nM), cells treated with DMC (50 nM) + rotenone (100 nM) and DMC alone treated. 24 h after treatment with rotenone and 28 h after treatment with DMC, cell viability was assessed using the MTT assay, and levels of ROS and MMP, plus expression of apoptotic protein were analysed. Rotenone induced cell death in SH-SY5Y cells was significantly reduced by DMC pretreatment in a dose-dependent manner, indicating the potent neuroprotective effects of DMC. Rotenone treatment significantly increases the levels of ROS, loss of MMP, release of Cyt-c and expression of pro-apoptotic markers and decreases the expression of anti-apoptotic markers. Even though the results of the present study indicated that the DMC may serve as a potent therapeutic agent particularly for the treatment of neurodegenerative diseases like PD, further pre-clinical and clinical studies are required.

Degradation and adsorption of carbonated dimethyl disulfide in soils with grape production in california

USDA-ARS?s Scientific Manuscript database

The common method to apply pre-plant soil fumigants is through pressurizing the pesticides with compressed nitrogen gas. However, it is believed that fumigants with relatively low vapor pressure, such as dimethyl disulfide or DMDS, can be better dispersed in soil when applied using CO2 gas. A labor...

Dimethyl disulfide (DMDS) and dimethyl sulfide (DMS) emissions from biomass burning in Australia

NASA Astrophysics Data System (ADS)

Meinardi, Simone; Simpson, Isobel J.; Blake, Nicola J.; Blake, Donald R.; Rowland, F. Sherwood

2003-05-01

We identify dimethyl disulfide (DMDS) as the major reduced sulfur-containing gas emitted from bushfires in Australia's Northern Territory. Like dimethyl sulfide (DMS), DMDS is oxidized in the atmosphere to sulfur dioxide (SO2) and methane sulfonic acid (MSA), which are intermediates in the formation of sulfuric acid (H2SO4). The mixing ratios of DMDS and DMS were the highest we have ever detected, with maximum values of 113 and 35 ppbv, respectively, whereas background values were below the detection limit (10 pptv). Molar emission ratios relative to carbon monoxide (CO) were [1.6 +/- 0.1] × 10-5 and [6.2 +/- 0.3] × 10-6, for DMDS and DMS respectively, while molar emission ratios relative to carbon dioxide (CO2) were [4.7 +/- 0.4] × 10-6 and [1.4 +/- 0.4] × 10-7, respectively. Assuming these observations are representative of biomass burning, we estimate that biomass burning could yield up to 175 Gg/yr of DMDS (119 Gg S/yr) and 13 Gg/yr of DMS.

Psychometric Properties of the Deep Muscle Contraction Scale for Assessment of the Drawing-in Maneuver in Patients With Chronic Nonspecific Low Back Pain.

PubMed

Oliveira, Crystian B; Negrão Filho, Ruben F; Franco, Márcia R; Morelhão, Priscila K; Araujo, Amanda C; Pinto, Rafael Z

2017-06-01

Study Design A prospective cohort study. Background Motor control dysfunctions have been commonly reported in patients with chronic nonspecific low back pain (LBP). Physical therapists need clinical tools with adequate psychometric properties to assess such patients in clinical practice. The deep muscle contraction (DMC) scale is a clinical rating scale for assessing patients' ability to voluntarily contract deep abdominal muscles. Objectives To investigate the intrarater reliability, floor and ceiling effects, internal and external responsiveness, and correlation analysis (with ultrasound measures) of the DMC scale in patients with chronic nonspecific LBP undergoing a lumbar stabilization exercise program. Methods Sixty-two patients with chronic nonspecific LBP were included. At baseline, self-report questionnaires were administered to patients and a trained assessor evaluated abdominal muscle recruitment with the DMC scale and ultrasound imaging. Four ratios of the change in abdominal muscle thickness between the resting and contracted states were calculated through the ultrasound measures. After 1 week, the same ultrasound measures and DMC scale were collected again for the reliability analysis. The proportions of patients with the lowest and highest scores on the DMC scale were calculated to investigate floor and ceiling effects. All patients underwent a lumbar stabilization program, administered twice a week for 8 weeks. After the treatment period, all measures were collected again, with the addition of the global perceived effect scale, to assess the internal and external responsiveness of the measures. Correlation coefficients between ultrasound ratios and DMC scale total and subscale scores were also calculated. Results The intrarater reliability of the DMC scale and the 4 ratios of abdominal muscle thickness varied from moderate to excellent. The DMC scale showed no floor or ceiling effects. Results for internal responsiveness of the DMC scale showed large effect sizes (2.26; 84% confidence interval [CI]: 2.06, 2.45), whereas the external responsiveness was below the proposed threshold (area under the curve = 0.54; 95% CI: 0.39, 0.68). Fair and significant correlations between some ultrasound ratios and DMC subscales were found. Conclusion The DMC scale was demonstrated to be a reliable tool, with no ceiling and floor effects, and to detect change in the ability to contract the deep abdominal muscles after a lumbar stabilization exercise program, but with low accuracy for estimating patient-perceived clinical outcome. J Orthop Sports Phys Ther 2017;47(6):432-441. doi:10.2519/jospt.2017.7140.

In vitro additive antitumor effects of dimethoxycurcumin and 5-fluorouracil in colon cancer cells.

PubMed

Zhao, Huiying; Liu, Qingchun; Wang, Saisai; Dai, Fang; Cheng, Xiaofei; Cheng, Xiaobin; Chen, Wenbin; Zhang, Min; Chen, Dong

2017-07-01

Dimethoxycurcumin (DMC) is a lipophilic analog of curcumin, an effective treatment for colon cancer, which has greater chemical and metabolic stability. Chemotherapy treatments, such as 5-fluorouracil (5-Fu), play a key role in the current management of colon cancer. In this study, we investigated the antitumor efficacy of DMC in combination with 5-Fu in SW480 and SW620 colon cancer cells. CCK-8 assay was used to evaluate the inhibitory effect of DMC and 5-Fu on cancer cells proliferation, and the combination index was calculated. The influence of DMC and 5-Fu on cell cycle, apoptosis, reactive oxygen species (ROS) production, and mitochondrial membrane potential in SW480 and SW620 cells was determined using flow cytometry, and the related signaling pathways were detected by western blot. Transmission electron microscopy was used to observe endoplasmic reticulum expansion. DMC- and/or 5-Fu-induced apoptosis, stimulated G0/G1 phase arrest, increased ROS levels, decreased mitochondrial membrane potential, and enhanced endoplasmic reticulum expansion. The induction of apoptosis is involved in the increasing of Bax and cytochrome c and decreasing of Bcl2 expressions. Increased production of ROS was accompanied by upregulation of CHOP and Noxa. Combination therapy of DMC and 5-Fu had increased efficacy on the above pathways compared with either drug alone. Based on the calculated IC 50 , combination treatment with DMC and 5-Fu had an additive antitumor effect in both cell lines. Combined treatment with DMC and 5-Fu led to an additive antitumor effect in colon cancer cells that was related to apoptosis induction, G0/G1 phase arrest, increased ROS production, decreased mitochondrial membrane potential, and enhanced endoplasmic reticulum expansion. © 2017 The Authors. Cancer Medicine published by John Wiley & Sons Ltd.

A New Way to Produce Cellobiose Carbonates Using Green Chemistry.

PubMed

Khiari, R; Brochier-Salon, M-C; Mhenni, M F; Mauret, E; Belgacem, M N

2016-08-23

The preparation of cellulose derivatives using green (i.e., environmentally friendly) reagents would improve sustainability and reduce concerns arising from the use of non-green reagents. The objective of this work was to prepare cellobiose carbonate using a green reagent, dimethyl carbonate. The carbonation reaction was carried out in the presence of ethanolic potassium hydroxide solution and dimethyl carbonate for 6 h at a range of temperatures (25-70 °C). A cellobiose derivative was successfully prepared with a recovered yield of more than 70 % and characterized by FTIR and NMR spectroscopy techniques. The presence of a grafted disaccharide with a degree of substitution higher than 2 was determined by (13) C NMR analysis. The spectra of the prepared cellobiose carbonate exhibited peaks that were associated with cellulose molecules (C1 -C6 ) and corresponded to carbonate functions at around 159.4 ppm. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Operationa1 Logistics 2010.

DTIC Science & Technology

1997-04-02

movements control center (MCC) which is co-located with a material management center (MMC) forming a distribution management center (DMC). The MMC...missions by a section in Support Operations called the Distribution Management Center (DMC)29. The DMC executes the distribution management (also...restructured organizations are the formula for making theater distribution a reality and the locus of these changes is the Distribution Management Center

Cohesive energy and structural parameters of binary oxides of groups IIA and IIIB from diffusion quantum Monte Carlo

DOE PAGES

Santana, Juan A.; Krogel, Jaron T.; Kent, Paul R. C.; ...

2016-05-03

We have applied the diffusion quantum Monte Carlo (DMC) method to calculate the cohesive energy and the structural parameters of the binary oxides CaO, SrO, BaO, Sc 2O 3, Y 2O 3 and La 2O 3. The aim of our calculations is to systematically quantify the accuracy of the DMC method to study this type of metal oxides. The DMC results were compared with local and semi-local Density Functional Theory (DFT) approximations as well as with experimental measurements. The DMC method yields cohesive energies for these oxides with a mean absolute deviation from experimental measurements of 0.18(2) eV, while withmore » local and semi-local DFT approximations the deviation is 3.06 and 0.94 eV, respectively. For lattice constants, the mean absolute deviation in DMC, local and semi-local DFT approximations, are 0.017(1), 0.07 and 0.05 , respectively. In conclusion, DMC is highly accurate method, outperforming the local and semi-local DFT approximations in describing the cohesive energies and structural parameters of these binary oxides.« less

Carbon dioxide recycling

EPA Science Inventory

The recycling of carbon dioxide to methanol and dimethyl ether is seen to offer a substantial route to renewable and environmentally carbon neutral fuels. One of the authors has championed the “Methanol Economy" in articles and a book. By recycling ambient CO2, the authors argue ...

Odor composition analysis and odor indicator selection during sewage sludge composting

PubMed Central

Zhu, Yan-li; Zheng, Guo-di; Gao, Ding; Chen, Tong-bin; Wu, Fang-kun; Niu, Ming-jie; Zou, Ke-hua

2016-01-01

ABSTRACT On the basis of total temperature increase, normal dehydration, and maturity, the odor compositions of surface and internal piles in a well-run sewage sludge compost plant were analyzed using gas chromatography–mass spectrometry with a liquid nitrogen cooling system and a portable odor detector. Approximately 80 types of substances were detected, including 2 volatile inorganic compounds, 4 sulfur organic compounds, 16 benzenes, 27 alkanes, 15 alkenes, and 19 halogenated compounds. Most pollutants were mainly produced in the mesophilic and pre-thermophilic periods. The sulfur volatile organic compounds contributed significantly to odor and should be controlled primarily. Treatment strategies should be based on the properties of sulfur organic compounds. Hydrogen sulfide, methyl mercaptan, dimethyl disulfide, dimethyl sulfide, ammonia, and carbon disulfide were selected as core indicators. Ammonia, hydrogen sulfide, carbon disulfide, dimethyl disulfide, methyl mercaptan, dimethylbenzene, phenylpropane, and isopentane were designated as concentration indicators. Benzene, m-xylene, p-xylene, dimethylbenzene, dichloromethane, toluene, chlorobenzene, trichloromethane, carbon tetrachloride, and ethylbenzene were selected as health indicators. According to the principle of odor pollution indicator selection, dimethyl disulfide was selected as an odor pollution indicator of sewage sludge composting. Monitoring dimethyl disulfide provides a highly scientific method for modeling and evaluating odor pollution from sewage sludge composting facilities. Implications: Composting is one of the most important methods for sewage sludge treatment and improving the low organic matter content of many agricultural soils. However, odors are inevitably produced during the composting process. Understanding the production and emission patterns of odors is important for odor control and treatment. Core indicators, concentration indicators, and health indicators provide an index system to odor evaluation. An odor pollution indicator provides theoretical support for further modelling and evaluating odor pollution from sewage sludge composting facilities. PMID:27192607

Odor composition analysis and odor indicator selection during sewage sludge composting.

PubMed

Zhu, Yan-Li; Zheng, Guo-di; Gao, Ding; Chen, Tong-Bin; Wu, Fang-Kun; Niu, Ming-Jie; Zou, Ke-Hua

2016-09-01

On the basis of total temperature increase, normal dehydration, and maturity, the odor compositions of surface and internal piles in a well-run sewage sludge compost plant were analyzed using gas chromatography-mass spectrometry with a liquid nitrogen cooling system and a portable odor detector. Approximately 80 types of substances were detected, including 2 volatile inorganic compounds, 4 sulfur organic compounds, 16 benzenes, 27 alkanes, 15 alkenes, and 19 halogenated compounds. Most pollutants were mainly produced in the mesophilic and pre-thermophilic periods. The sulfur volatile organic compounds contributed significantly to odor and should be controlled primarily. Treatment strategies should be based on the properties of sulfur organic compounds. Hydrogen sulfide, methyl mercaptan, dimethyl disulfide, dimethyl sulfide, ammonia, and carbon disulfide were selected as core indicators. Ammonia, hydrogen sulfide, carbon disulfide, dimethyl disulfide, methyl mercaptan, dimethylbenzene, phenylpropane, and isopentane were designated as concentration indicators. Benzene, m-xylene, p-xylene, dimethylbenzene, dichloromethane, toluene, chlorobenzene, trichloromethane, carbon tetrachloride, and ethylbenzene were selected as health indicators. According to the principle of odor pollution indicator selection, dimethyl disulfide was selected as an odor pollution indicator of sewage sludge composting. Monitoring dimethyl disulfide provides a highly scientific method for modeling and evaluating odor pollution from sewage sludge composting facilities. Composting is one of the most important methods for sewage sludge treatment and improving the low organic matter content of many agricultural soils. However, odors are inevitably produced during the composting process. Understanding the production and emission patterns of odors is important for odor control and treatment. Core indicators, concentration indicators, and health indicators provide an index system to odor evaluation. An odor pollution indicator provides theoretical support for further modelling and evaluating odor pollution from sewage sludge composting facilities.

Radiolabeled dimethyl branched long chain fatty acid for heart imaging

DOEpatents

Knapp, Jr., Furn F.; Goodman, Mark M.; Kirsch, Gilbert

1988-08-16

A radiolabeled long chain fatty acid for heart imaging that has dimethyl branching at one of the carbons of the chain which inhibits the extent to which oxidation can occur. The closer to the carboxyl the branching is positioned, the more limited the oxidation, thereby resulting in prolonged retention of the radiolabeled compound in the heart.

The fission yeast meiosis-specific Dmc1 recombinase mediates formation and branch migration of Holliday junctions by preferentially promoting strand exchange in a direction opposite to that of Rad51

PubMed Central

Murayama, Yasuto; Tsutsui, Yasuhiro; Iwasaki, Hiroshi

2011-01-01

Homologous recombination proceeds via the formation of several intermediates including Holliday junctions (HJs), which are important for creating crossover products. DNA strand exchange is a core reaction that produces these intermediates that is directly catalyzed by RecA family recombinases, of which there are two types in eukaryotes: universal Rad51 and meiosis-specific Dmc1. We demonstrated previously that Rad51 promotes four-strand exchange, mimicking the formation and branch migration of HJs. Here we show that Dmc1 from fission yeast has a similar activity, which requires ATP hydrolysis and is independent of an absolute requirement for the Swi5–Sfr1 complex. These features are critically different from three-strand exchange mediated by Dmc1, but similar to those of four-strand exchange mediated by Rad51, suggesting that strand exchange reactions between duplex–duplex and single-duplex DNAs are mechanistically different. Interestingly, despite similarities in protein structure and in reaction features, the preferential polarities of Dmc1 and Rad51 strand exchange are different (Dmc1 promotes exchange in the 5′-to-3′ direction and Rad51 promotes exchange in the 3′-to-5′ direction relative to the ssDNA region of the DNA substrate). The significance of the Dmc1 polarity is discussed within the context of the necessity for crossover production. PMID:21363965

Depression and decision-making capacity for treatment or research: a systematic review

PubMed Central

2013-01-01

Background Psychiatric disorders can pose problems in the assessment of decision-making capacity (DMC). This is so particularly where psychopathology is seen as the extreme end of a dimension that includes normality. Depression is an example of such a psychiatric disorder. Four abilities (understanding, appreciating, reasoning and ability to express a choice) are commonly assessed when determining DMC in psychiatry and uncertainty exists about the extent to which depression impacts capacity to make treatment or research participation decisions. Methods A systematic review of the medical ethical and empirical literature concerning depression and DMC was conducted. Medline, EMBASE and PsycInfo databases were searched for studies of depression and consent and DMC. Empirical studies and papers containing ethical analysis were extracted and analysed. Results 17 publications were identified. The clinical ethics studies highlighted appreciation of information as the ability that can be impaired in depression, indicating that emotional factors can impact on DMC. The empirical studies reporting decision-making ability scores also highlighted impairment of appreciation but without evidence of strong impact. Measurement problems, however, looked likely. The frequency of clinical judgements of lack of DMC in people with depression varied greatly according to acuity of illness and whether judgements are structured or unstructured. Conclusions Depression can impair DMC especially if severe. Most evidence indicates appreciation as the ability primarily impaired by depressive illness. Understanding and measuring the appreciation ability in depression remains a problem in need of further research. PMID:24330745

Effects of demethoxycurcumin on the viability and apoptosis of skin cancer cells.

PubMed

Wu, Yaoqun; Zhang, Pei; Yang, Hongyun; Ge, Yong; Xin, Yong

2017-07-01

The present study investigated the effects and mechanisms of demethoxycurcumin (DMC) on a human skin squamous cell carcinoma cell line, A431, and a human keratinocyte cell line, HaCaT. A431 and HaCaT cells were cultured in vitro. The effects of DMC treatment on cell viability were analyzed using the Cell Counting kit‑8 (CCK‑8) assay; cell cycle distribution was analyzed by flow cytometry; apoptosis was assessed by flow cytometry and Hoechst 33258 staining; and the protein expression levels of cytochrome c, B‑cell lymphoma 2 (Bcl‑2), Bcl‑2‑associated X protein (BAX), caspase‑9 and caspase‑3 were evaluated by western blotting. CCK‑8 assay results demonstrated that DMC treatment significantly inhibited viability of A431 and HaCaT cells in a dose‑dependent manner. Flow cytometric analysis confirmed that DMC treatment induced apoptosis in a dose‑dependent manner, and significantly increased the proportion of cells in G2/M phase. Western blot analysis indicated that the protein expression levels of Bcl‑2 were decreased, whereas the expression levels of BAX, caspase‑9, caspase‑3 and cytochrome c were increased following DMC treatment compared with in untreated cells. In conclusion, DMC treatment significantly inhibited viability of A431 and HaCaT cells, and induced cell cycle arrest in G2/M phase. The present study indicated that DMC may induce apoptosis of skin cancer cells through a caspase‑dependent pathway.

Structural Stability and Defect Energetics of ZnO from Diffusion Quantum Monte Carlo

DOE PAGES

Santana Palacio, Juan A.; Krogel, Jaron T.; Kim, Jeongnim; ...

2015-04-28

We have applied the many-body ab-initio diffusion quantum Monte Carlo (DMC) method to study Zn and ZnO crystals under pressure, and the energetics of the oxygen vacancy, zinc interstitial and hydrogen impurities in ZnO. We show that DMC is an accurate and practical method that can be used to characterize multiple properties of materials that are challenging for density functional theory approximations. DMC agrees with experimental measurements to within 0.3 eV, including the band-gap of ZnO, the ionization potential of O and Zn, and the atomization energy of O2, ZnO dimer, and wurtzite ZnO. DMC predicts the oxygen vacancy asmore » a deep donor with a formation energy of 5.0(2) eV under O-rich conditions and thermodynamic transition levels located between 1.8 and 2.5 eV from the valence band maximum. Our DMC results indicate that the concentration of zinc interstitial and hydrogen impurities in ZnO should be low under n-type, and Zn- and H-rich conditions because these defects have formation energies above 1.4 eV under these conditions. Comparison of DMC and hybrid functionals shows that these DFT approximations can be parameterized to yield a general correct qualitative description of ZnO. However, the formation energy of defects in ZnO evaluated with DMC and hybrid functionals can differ by more than 0.5 eV.« less

ASC Distribution Management Center (DMC) Provides Materiel Management Capability

DTIC Science & Technology

2008-09-01

Distribution Management Center (DMC) is the single interface for the synchronization and integration of logistical functions among active Army units in CONUS...with an integrated team of Soldiers, government service employees, and contractors assigned to Rock Island, as well as forward-positioned Distribution ... Management Teams (DMTs) at 15 major Army installations throughout CONUS, Alaska, and Hawaii. The current DMC structure provides the benefit of

Improvement of in vitro and in vivo antileishmanial activities of 2', 6'-dihydroxy-4'-methoxychalcone by entrapment in poly(D,L-lactide) nanoparticles.

PubMed

Torres-Santos, E C; Rodrigues, J M; Moreira, D L; Kaplan, M A; Rossi-Bergmann, B

1999-07-01

The inhibition of intracellular Leishmania amazonensis growth by 2', 6'-dihydroxy-4'-methoxychalcone (DMC) isolated from Piper aduncum was further enhanced after encapsulation of DMC in polymeric nanoparticles. Encapsulated DMC also showed increased antileishmanial activity in infected BALB/c mice, as evidenced by significantly smaller lesions and fewer parasites in the lesions.

Meiotic Crossover Control by Concerted Action of Rad51-Dmc1 in Homolog Template Bias and Robust Homeostatic Regulation

PubMed Central

Huang, Chu-Chun; Grubb, Jennifer; Thacker, Drew; Lee, Chih-Ying; Dresser, Michael E.; Hunter, Neil; Bishop, Douglas K.

2013-01-01

During meiosis, repair of programmed DNA double-strand breaks (DSBs) by recombination promotes pairing of homologous chromosomes and their connection by crossovers. Two DNA strand-exchange proteins, Rad51 and Dmc1, are required for meiotic recombination in many organisms. Studies in budding yeast imply that Rad51 acts to regulate Dmc1's strand exchange activity, while its own exchange activity is inhibited. However, in a dmc1 mutant, elimination of inhibitory factor, Hed1, activates Rad51's strand exchange activity and results in high levels of recombination without participation of Dmc1. Here we show that Rad51-mediated meiotic recombination is not subject to regulatory processes associated with high-fidelity chromosome segregation. These include homolog bias, a process that directs strand exchange between homologs rather than sister chromatids. Furthermore, activation of Rad51 does not effectively substitute for Dmc1's chromosome pairing activity, nor does it ensure formation of the obligate crossovers required for accurate homolog segregation. We further show that Dmc1's dominance in promoting strand exchange between homologs involves repression of Rad51's strand-exchange activity. This function of Dmc1 is independent of Hed1, but requires the meiotic kinase, Mek1. Hed1 makes a relatively minor contribution to homolog bias, but nonetheless this is important for normal morphogenesis of synaptonemal complexes and efficient crossing-over especially when DSB numbers are decreased. Super-resolution microscopy shows that Dmc1 also acts to organize discrete complexes of a Mek1 partner protein, Red1, into clusters along lateral elements of synaptonemal complexes; this activity may also contribute to homolog bias. Finally, we show that when interhomolog bias is defective, recombination is buffered by two feedback processes, one that increases the fraction of events that yields crossovers, and a second that we propose involves additional DSB formation in response to defective homolog interactions. Thus, robust crossover homeostasis is conferred by integrated regulation at initiation, strand-exchange and maturation steps of meiotic recombination. PMID:24367271

Tools for Integrating Data Access from the IRIS DMC into Research Workflows

NASA Astrophysics Data System (ADS)

Reyes, C. G.; Suleiman, Y. Y.; Trabant, C.; Karstens, R.; Weertman, B. R.

2012-12-01

Web service interfaces at the IRIS Data Management Center (DMC) provide access to a vast archive of seismological and related geophysical data. These interfaces are designed to easily incorporate data access into data processing workflows. Examples of data that may be accessed include: time series data, related metadata, and earthquake information. The DMC has developed command line scripts, MATLAB® interfaces and a Java library to support a wide variety of data access needs. Users of these interfaces do not need to concern themselves with web service details, networking, or even (in most cases) data conversion. Fetch scripts allow access to the DMC archive and are a comfortable fit for command line users. These scripts are written in Perl and are well suited for automation and integration into existing workflows on most operating systems. For metdata and event information, the Fetch scripts even parse the returned data into simple text summaries. The IRIS Java Web Services Library (IRIS-WS Library) allows Java developers the ability to create programs that access the DMC archives seamlessly. By returning the data and information as native Java objects the Library insulates the developer from data formats, network programming and web service details. The MATLAB interfaces leverage this library to allow users access to the DMC archive directly from within MATLAB (r2009b or newer), returning data into variables for immediate use. Data users and research groups are developing other toolkits that use the DMC's web services. Notably, the ObsPy framework developed at LMU Munich is a Python Toolbox that allows seamless access to data and information via the DMC services. Another example is the MATLAB-based GISMO and Waveform Suite developments that can now access data via web services. In summary, there now exist a host of ways that researchers can bring IRIS DMC data directly into their workflows. MATLAB users can use irisFetch.m, command line users can use the various Fetch scripts, Java users can use the IRIS-WS library, and Python users may request data through ObsPy. To learn more about any of these clients see http://www.iris.edu/ws/wsclients/.

Phosphonate–Phosphinate Rearrangement

PubMed Central

2014-01-01

LiTMP metalated dimethyl N-Boc-phosphoramidates derived from 1-phenylethylamine and 1,2,3,4-tetrahydronaphthalen-1-ylamine highly selectively at the CH3O group to generate short-lived oxymethyllithiums. These isomerized to diastereomeric hydroxymethylphosphonamidates (phosphate–phosphonate rearrangement). However, s-BuLi converted the dimethyl N-Boc-phosphoramidate derived from 1-phenylethylamine to the N-Boc α-aminophosphonate preferentially. Only s-BuLi deprotonated dimethyl hydroxymethylphosphonamidates at the benzylic position and dimethyl N-Boc α-aminophosphonates at the CH3O group to induce phosphonate–phosphinate rearrangements. In the former case, the migration of the phosphorus substituent from the nitrogen to the carbon atom followed a retentive course with some racemization because of the involvement of a benzyllithium as an intermediate. PMID:25525945

Solvent dependent photophysical properties of dimethoxy curcumin

NASA Astrophysics Data System (ADS)

Barik, Atanu; Indira Priyadarsini, K.

2013-03-01

Dimethoxy curcumin (DMC) is a methylated derivative of curcumin. In order to know the effect of ring substitution on photophysical properties of curcumin, steady state absorption and fluorescence spectra of DMC were recorded in organic solvents with different polarity and compared with those of curcumin. The absorption and fluorescence spectra of DMC, like curcumin, are strongly dependent on solvent polarity and the maxima of DMC showed red shift with increase in solvent polarity function (Δf), but the above effect is prominently observed in case of fluorescence maxima. From the dependence of Stokes' shift on solvent polarity function the difference between the excited state and ground state dipole moment was estimated as 4.9 D. Fluorescence quantum yield (ϕf) and fluorescence lifetime (τf) of DMC were also measured in different solvents at room temperature. The results indicated that with increasing solvent polarity, ϕf increased linearly, which has been accounted for the decrease in non-radiative rate by intersystem crossing (ISC) processes.

Small Rad51 and Dmc1 Complexes Often Co-occupy Both Ends of a Meiotic DNA Double Strand Break

PubMed Central

Brown, M. Scott; Grubb, Jennifer; Zhang, Annie; Rust, Michael J.; Bishop, Douglas K.

2015-01-01

The Eukaryotic RecA-like proteins Rad51 and Dmc1 cooperate during meiosis to promote recombination between homologous chromosomes by repairing programmed DNA double strand breaks (DSBs). Previous studies showed that Rad51 and Dmc1 form partially overlapping co-foci. Here we show these Rad51-Dmc1 co-foci are often arranged in pairs separated by distances of up to 400 nm. Paired co-foci remain prevalent when DSBs are dramatically reduced or when strand exchange or synapsis is blocked. Super-resolution dSTORM microscopy reveals that individual foci observed by conventional light microscopy are often composed of two or more substructures. The data support a model in which the two tracts of ssDNA formed by a single DSB separate from one another by distances of up to 400 nm, with both tracts often bound by one or more short (about 100 nt) Rad51 filaments and also by one or more short Dmc1 filaments. PMID:26719980

Diabetes-related heart failure.

PubMed

Bando, Yasuko K; Murohara, Toyoaki

2014-01-01

As the link between heart failure (HF) and diabetes mellitus (DM) becomes unignorable, so the need is further increasing for pathological comprehension: What is "diabetic cardiomyopathy (DMC)?" In response to current concern, the most updated guidelines stated by the ACCF/AHA and by the ESC/EASD take one step further, including the definition of DMC, although it is a matter yet to be completed. For more than 40 years, coronary artery disease and hypertension have been considered as the main causes of diabetes-related cardiac dysfunction. HF was originally considered as a result of reduced left ventricular ejection fraction (HF-REF); however, it has been recognized that HF symptoms are often observed in patients with preserved EF (HF-PEF). DMC includes HF with both reduced and preserved entities independent of coronary stenosis and hypertension. Cardiologists are thus facing a sort of chaos without clear guidelines for the "deadly intersection" of DM and HF. Today, the increasing interest and concern have caused DMC to be revisited and the first step in controlling the chaos around DMC is to organize and analyze all of the available evidence from preclinical and clinical studies. This review aims to illustrate the current concepts of DMC by shedding light on the new molecular mechanisms.  (Circ J 2014; 78: 576-583).

Influence of management regime and harvest date on the forage quality of rangelands plants: the importance of dry matter content

PubMed Central

Bumb, Iris; Garnier, Eric; Bastianelli, Denis; Richarte, Jean; Bonnal, Laurent; Kazakou, Elena

2016-01-01

In spite of their recognized ecological value, relatively little is known about the nutritional value of species-rich rangelands for herbivores. We investigated the sources of variation in dry matter digestibility (DMD), neutral detergent fibre content (NDF) and nitrogen concentration (NC) in plants from species-rich Mediterranean rangelands in southern France, and tested whether the dry matter content (DMC) was a good predictor of the forage quality of different plant parts. Sixteen plant species with contrasting growth forms (rosette, tussock, extensive and stemmed-herb) were studied, representative of two management regimes imposed in these rangelands: (i) fertilization and intensive grazing and (ii) non-fertilization and moderate grazing. Among the 16 plant species, four species were found in both treatments, allowing us to assess the intraspecific variability in forage quality and DMC across the treatments. The components of nutritional value (DMD, NDF and NC) as well as the DMC of leaves, stems and reproductive plant parts, were assessed at the beginning of the growing season and at peak standing biomass. All components of nutritional value and DMC were affected by species growth form: rosettes had higher DMD and NC than tussocks; the reverse being found for NDF and DMC. As the season progressed, DMD and NC of the different plant parts decreased while NDF and DMC increased for all species. DMC was negatively related to DMD and NC and positively to NDF, regardless of the source of variation (species, harvest date, management regime or plant part). Path analysis indicated that NDF was the main determinant of DMD. Better assessment of forage quality in species-rich systems requires consideration of their growth form composition. DMC of all plant parts, which is closely related to NDF, emerged as a good predictor and easily measured trait to estimate DMD in these species-rich systems. PMID:27339049

Improvement of In Vitro and In Vivo Antileishmanial Activities of 2′,6′-Dihydroxy-4′-Methoxychalcone by Entrapment in Poly(d,l-Lactide) Nanoparticles

PubMed Central

Torres-Santos, Eduardo Caio; Rodrigues, José M.; Moreira, Davyson L.; Kaplan, Maria Auxiliadora C.; Rossi-Bergmann, Bartira

1999-01-01

The inhibition of intracellular Leishmania amazonensis growth by 2′,6′-dihydroxy-4′-methoxychalcone (DMC) isolated from Piper aduncum was further enhanced after encapsulation of DMC in polymeric nanoparticles. Encapsulated DMC also showed increased antileishmanial activity in infected BALB/c mice, as evidenced by significantly smaller lesions and fewer parasites in the lesions. PMID:10390243

DOE Office of Scientific and Technical Information (OSTI.GOV)

Preece, D.S.; Knudsen, S.D.

The spherical element computer code DMC (Distinct Motion Code) used to model rock motion resulting from blasting has been enhanced to allow routine computer simulations of bench blasting. The enhancements required for bench blast simulation include: (1) modifying the gas flow portion of DMC, (2) adding a new explosive gas equation of state capability, (3) modifying the porosity calculation, and (4) accounting for blastwell spacing parallel to the face. A parametric study performed with DMC shows logical variation of the face velocity as burden, spacing, blastwell diameter and explosive type are varied. These additions represent a significant advance in themore » capability of DMC which will not only aid in understanding the physics involved in blasting but will also become a blast design tool. 8 refs., 7 figs., 1 tab.« less

Development of Lithium Dimethyl Phosphate as an Electrolyte Additive for Lithium Ion Batteries

DOE PAGES

Milien, Mickdy S.; Tottempudi, Usha; Son, Miyoung; ...

2016-04-27

The novel electrolyte additive lithium dimethyl phosphate (LiDMP) has been synthesized and characterized. Incorporation of LiDMP (0.1% wt) into LiPF 6 in ethylene carbonate (EC) / ethyl methyl carbonate (EMC) (3:7 wt) results in improved rate performance and reduced impedance for graphite / LiNi 1/3Mn 1/3Co 1/3O 2 cells. Ex-situ surface analysis of the electrodes suggests that incorporation of LiDMP results in a modification of the solid electrolyte interphase (SEI) on the anode. A decrease in the concentration of lithium alkyl carbonates and an increase in the concentration of lithium fluoro phosphates are observed. The change in the anode SEImore » structure is responsible for the increased rate performance and decreased cell impedance.« less

The combined EarthScope data set at the IRIS DMC

NASA Astrophysics Data System (ADS)

Trabant, C.; Sharer, G.; Benson, R.; Ahern, T.

2007-12-01

The IRIS Data Management Center (DMC) is the perpetual archive and access point for an ever-increasing variety of geophysical data in terms of volume, geographic distribution and scientific value. A particular highlight is the combined data set produced by the EarthScope project. The DMC archives data from each of the primary components: USArray, the Plate Boundary Observatory (PBO) & the San Andreas Fault Observatory at Depth (SAFOD). Growing at over 4.6 gigabytes per day, the USArray data set currently totals approximately 5 terabytes. Composed of four separate sub-components: the Permanent, Transportable, Flexible and Magnetotelluric Arrays, the USArray data set provides a multi-scale view of the western United States at present and the conterminous United States when it is completed. The primary data from USArray are in the form of broadband and short-period seismic recordings and magnetotelluric measurements. Complementing the data from USArray are the short- period, borehole seismic data and borehole and laser strain data from PBO. The DMC also archives the high- resolution seismic data from instruments in the SAFOD main and pilot drill holes. The SAFOD seismic data is available in two forms: lower-rate monitoring channels sampled at 250 hertz and full resolution channels varying between 1 and 4 kilohertz. Beyond data collection and archive management the DMC performs value-added functions. All data arriving at the DMC as real-time data streams are processed by QUACK, an automated Quality Control (QC) system. All the measurements made by this system are stored in a database and made available to data contributors and users via a web interface including customized report generation. In addition to the automated QC measurements, quality control is performed on USArray data at the DMC by a team of analysts. The primary functions of the analysts are to routinely report data quality assessment to the respective network operators and log serious, unfixable data issues for reference by data users. All of these data are managed in a unified SEED format archive and are seamlessly available to data users via the DMC's&pstandard data access methods along with all the other data managed by the DMC. The only exception is high resolution, special case SAFOD seismic data that is retained in its original SEG-2 format as an assembled data set. A data user can choose between a handful of data access methods ranging from simple email requests to technologically advanced CORBA-based access, streamlining the "information into application" philosophy. Currently totally over 8.5 terabytes and growing, the combined EarthScope data at the DMC provides an unparalleled, multi-measurement record of geophysical information ideal for determining Earth structure and processes in the United States and beyond. A website is maintained to provide current information regarding EarthScope data at the DMC: http://www.iris.edu/earthscope/.

Molecular Basis for Enhancement of the Meiotic DMCI Recombinase by RAD51AP1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dray, Eloise; Dunlop, Myun Hwa; Kauppi, Liisa

Homologous recombination is needed for meiotic chromosome segregation, genome maintenance, and tumor suppression. RAD51AP1 (RAD51 Associated Protein 1) has been shown to interact with and enhance the recombinase activity of RAD51. Accordingly, genetic ablation of RAD51AP1 leads to enhanced sensitivity to and also chromosome aberrations upon DNA damage, demonstrating a role for RAD51AP1 in mitotic homologous recombination. Here we show physical association of RAD51AP1 with the meiosis-specific recombinase DMC1 and a stimulatory effect of RAD51AP1 on the DMC1-mediated D-loop reaction. Mechanistic studies have revealed that RAD51AP1 enhances the ability of the DMC1 presynaptic filament to capture the duplex DNA partnermore » and to assemble the synaptic complex, in which the recombining DNA strands are homologously aligned. We also provide evidence that functional co-operation is dependent on complex formation between DMC1 and RAD51AP1, and that distinct epitopes in RAD51AP1 mediate interactions with RAD51 and DMC1. Finally, we show that RAD51AP1 is expressed in mouse testes, and that RAD51AP1 foci co-localize with a subset of DMC1 foci in spermatocytes. These results suggest that RAD51AP1 also serves an important role in meiotic homologous recombination.« less

Determinants of psychogeriatric inpatient length of stay and direct medical costs: a 6-year longitudinal study using a national database in Taiwan.

PubMed

Liu, Chin-Ming; Li, Chu-Shiu; Liu, Chwen-Chi; Tu, Chu-Chin

2012-08-01

This research examined factors related to the average length of hospital stay (LOS) and average direct medical costs (DMC) for 2291 psychogeriatric inpatients (aged 65 and over) admitted for the first time to a psychiatric ward in 2002. Hospitalization claim data of these inpatients were traced for the subsequent 6 years (2002-2007) from the dataset of Taiwan's National Health Insurance program. Analysis was carried out using the t-test, χ(2) -test and zero truncated Tobit regression. Mean LOS and mean DMC were significantly different according to sex, psychiatric diagnosis, institution type, ownership type, and number of hospitalizations, but age was the exception. Both LOS and DMC exhibited downward U-shape for the number of hospitalizations. Factors significantly associated with longer LOS and higher DMC were: male sex; schizophrenic and delusional disorders (compared with dementia); and public institution (compared with private hospital). Compared with dementia, organic mental and anxiety disorders had significantly shorter LOS, and affective disorders had shorter LOS but higher DMC. Community and psychiatric hospitals (compared with general hospital) significantly influenced LOS but not DMC. Our results can be used as a reference for providers and policymakers to improve psychiatric care efficiency and carry out National Health Insurance financial reform for psychogeriatric inpatients. © 2012 The Authors. Psychiatry and Clinical Neurosciences © 2012 Japanese Society of Psychiatry and Neurology.

[Needles stable carbon isotope composition and traits of Pinus sylvestris var. mongolica in sparse wood grassland in south edge of Keerqin Sandy Land under the conditions of different precipitation].

PubMed

Song, Li-Ning; Zhu, Jiao-Jun; Li, Ming-Cai; Yan, Tao; Zhang, Jin-Xin

2012-06-01

A comparative study was conducted on the needles stable carbon isotope composition (delta13 C), specific leaf area (SLA), and dry matter content (DMC) of 19-year-old Pinus sylvestris var. mongolica trees in a sparse wood grassland in the south edge of Keerqin Sandy Land under the conditions of extreme drought and extreme wetness, aimed to understand the water use of Pinus sylvestris under the conditions of extreme precipitation. The soil water content and groundwater level were also measured. In the dry year (2009), the soil water content in the grassland was significantly lower than that in the wet year (2010), but the delta13C values of the current year-old needles had no significant difference between the two years and between the same months of the two years. The SLA of the current year-old needles was significantly lower in the dry year than in the wet year, but the DMC had no significant difference between the two years. Under the conditions of the two extreme precipitations, the water use efficiency of the trees did not vary remarkably, and the trees could change their needles SLA to adapt the variations of precipitation. For the test ecosystem with a groundwater level more than 3.0 m, extreme drought could have no serious impact on the growth and survival of the trees.

Estimating current and future global urban domestic material consumption

NASA Astrophysics Data System (ADS)

Baynes, Timothy Malcolm; Kaviti Musango, Josephine

2018-06-01

Urban material resource requirements are significant at the global level and these are expected to expand with future urban population growth. However, there are no global scale studies on the future material consumption of urban areas. This paper provides estimates of global urban domestic material consumption (DMC) in 2050 using three approaches based on: current gross statistics; a regression model; and a transition theoretic logistic model. All methods use UN urban population projections and assume a simple ‘business-as-usual’ scenario wherein historical aggregate trends in income and material flow continue into the future. A collation of data for 152 cities provided a year 2000 world average DMC/capita estimate, 12 tons/person/year (±22%), which we combined with UN population projections to produce a first-order estimation of urban DMC at 2050 of ~73 billion tons/year (±22%). Urban DMC/capita was found to be significantly correlated (R 2 > 0.9) to urban GDP/capita and area per person through a power law relation used to obtain a second estimate of 106 billion tons (±33%) in 2050. The inelastic exponent of the power law indicates a global tendency for relative decoupling of direct urban material consumption with increasing income. These estimates are global and influenced by the current proportion of developed-world cities in the global population of cities (and in our sample data). A third method employed a logistic model of transitions in urban DMC/capita with regional resolution. This method estimated global urban DMC to rise from approximately 40 billion tons/year in 2010 to ~90 billion tons/year in 2050 (modelled range: 66–111 billion tons/year). DMC/capita across different regions was estimated to converge from a range of 5–27 tons/person/year in the year 2000 to around 8–17 tons/person/year in 2050. The urban population does not increase proportionally during this period and thus the global average DMC/capita increases from ~12 to ~14 tons/person/year, challenging resource decoupling targets.

Recruitment of RecA homologs Dmc1p and Rad51p to the double-strand break repair site initiated by meiosis-specific endonuclease VDE (PI-SceI).

PubMed

Fukuda, Tomoyuki; Ohya, Yoshikazu

2006-02-01

During meiosis, VDE (PI-SceI), a homing endonuclease in Saccharomyces cerevisiae, introduces a double-strand break (DSB) at its recognition sequence and induces homologous recombinational repair, called homing. Meiosis-specific RecA homolog Dmc1p, as well as mitotic RecA homolog Rad51p, acts in the process of meiotic recombination, being required for strand invasion and exchange. In this study, recruitment of Dmc1p and Rad51p to the VDE-induced DSB repair site is investigated by chromatin immunoprecipitation assay. It is revealed that Dmc1p and Rad51p are loaded to the repair site in an independent manner. Association of Rad51p requires other DSB repair proteins of Rad52p, Rad55p, and Rad57p, while loading of Dmc1p is facilitated by the different protein, Sae3p. Absence of Tid1p, which can bind both RecA homologs, appears specifically to cause an abnormal distribution of Dmc1p. Lack of Hop2, Mnd1p, and Sae1p does not impair recruitment of both RecA homologs. These findings reveal the discrete functions of each strand invasion protein in VDE-initiated homing, confirm the similarity between VDE-initiated homing and Spo11p-initiated meiotic recombination, and demonstrate the availability of VDE-initiated homing for the study of meiotic recombination.

Role of solvents on the oxygen reduction and evolution of rechargeable Li-O2 battery

NASA Astrophysics Data System (ADS)

Christy, Maria; Arul, Anupriya; Zahoor, Awan; Moon, Kwang Uk; Oh, Mi Young; Stephan, A. Manuel; Nahm, Kee Suk

2017-02-01

The choice of electrolyte solvent is expected to play a key role in influencing the lithium-oxygen battery performance. The electrochemical performances of three electrolytes composed of lithium bis (trifluoromethane sulfonyl) imide (LiTFSI) salt and different solvents namely, ethylene carbonate/propylene carbonate (EC/PC), tetra ethylene glycol dimethyl ether (TEGDME) and dimethyl sulfoxide (DMSO) are investigated by assembling lithium oxygen cells. The electrolyte composition significantly varied the specific capacity of the battery. The choice of electrolyte also influences the overpotential, cycle life, and rechargeability of the battery. Electrochemical impedance spectra, cyclic voltammetry, and chronoamperometry were utilized to determine the reversible reactions associated with the air cathode.

High-energy metal air batteries

DOEpatents

Zhang, Ji-Guang; Xiao, Jie; Xu, Wu; Wang, Deyu; Williford, Ralph E.; Liu, Jun

2014-07-01

Disclosed herein are embodiments of lithium/air batteries and methods of making and using the same. Certain embodiments are pouch-cell batteries encased within an oxygen-permeable membrane packaging material that is less than 2% of the total battery weight. Some embodiments include a hybrid air electrode comprising carbon and an ion insertion material, wherein the mass ratio of ion insertion material to carbon is 0.2 to 0.8. The air electrode may include hydrophobic, porous fibers. In particular embodiments, the air electrode is soaked with an electrolyte comprising one or more solvents including dimethyl ether, and the dimethyl ether subsequently is evacuated from the soaked electrode. In other embodiments, the electrolyte comprises 10-20% crown ether by weight.

High-energy metal air batteries

DOEpatents

Zhang, Ji-Guang; Xiao, Jie; Xu, Wu; Wang, Deyu; Williford, Ralph E.; Liu, Jun

2013-07-09

Disclosed herein are embodiments of lithium/air batteries and methods of making and using the same. Certain embodiments are pouch-cell batteries encased within an oxygen-permeable membrane packaging material that is less than 2% of the total battery weight. Some embodiments include a hybrid air electrode comprising carbon and an ion insertion material, wherein the mass ratio of ion insertion material to carbon is 0.2 to 0.8. The air electrode may include hydrophobic, porous fibers. In particular embodiments, the air electrode is soaked with an electrolyte comprising one or more solvents including dimethyl ether, and the dimethyl ether subsequently is evacuated from the soaked electrode. In other embodiments, the electrolyte comprises 10-20% crown ether by weight.

Programmatic access to data and information at the IRIS DMC via web services

NASA Astrophysics Data System (ADS)

Weertman, B. R.; Trabant, C.; Karstens, R.; Suleiman, Y. Y.; Ahern, T. K.; Casey, R.; Benson, R. B.

2011-12-01

The IRIS Data Management Center (DMC) has developed a suite of web services that provide access to the DMC's time series holdings, their related metadata and earthquake catalogs. In addition, services are available to perform simple, on-demand time series processing at the DMC prior to being shipped to the user. The primary goal is to provide programmatic access to data and processing services in a manner usable by and useful to the research community. The web services are relatively simple to understand and use and will form the foundation on which future DMC access tools will be built. Based on standard Web technologies they can be accessed programmatically with a wide range of programming languages (e.g. Perl, Python, Java), command line utilities such as wget and curl or with any web browser. We anticipate these services being used for everything from simple command line access, used in shell scripts and higher programming languages to being integrated within complex data processing software. In addition to improving access to our data by the seismological community the web services will also make our data more accessible to other disciplines. The web services available from the DMC include ws-bulkdataselect for the retrieval of large volumes of miniSEED data, ws-timeseries for the retrieval of individual segments of time series data in a variety of formats (miniSEED, SAC, ASCII, audio WAVE, and PNG plots) with optional signal processing, ws-station for station metadata in StationXML format, ws-resp for the retrieval of instrument response in RESP format, ws-sacpz for the retrieval of sensor response in the SAC poles and zeros convention and ws-event for the retrieval of earthquake catalogs. To make the services even easier to use, the DMC is developing a library that allows Java programmers to seamlessly retrieve and integrate DMC information into their own programs. The library will handle all aspects of dealing with the services and will parse the returned data. By using this library a developer will not need to learn the details of the service interfaces or understand the data formats returned. This library will be used to build the software bridge needed to request data and information from within MATLAB°. We also provide several client scripts written in Perl for the retrieval of waveform data, metadata and earthquake catalogs using command line programs. For more information on the DMC's web services please visit http://www.iris.edu/ws/

Diffusion quantum Monte Carlo calculations of SrFeO 3 and LaFeO 3

DOE PAGES

Santana, Juan A.; Krogel, Jaron T.; Kent, Paul R. C.; ...

2017-07-18

The equations of state, formation energy, and migration energy barrier of the oxygen vacancy in SrFeO 3 and LaFeO 3 were calculated in this paper with the diffusion quantum Monte Carlo (DMC) method. Calculations were also performed with various Density Functional Theory (DFT) approximations for comparison. DMC reproduces the measured cohesive energies of these materials with errors below 0.23(5) eV and the structural properties within 1% of the experimental values. The DMC formation energies of the oxygen vacancy in SrFeO 3 and LaFeO 3 under oxygen-rich conditions are 1.3(1) and 6.24(7) eV, respectively. Similar calculations with semi-local DFT approximations formore » LaFeO 3 yielded vacancy formation energies 1.5 eV lower. Comparison of charge density evaluated with DMC and DFT approximations shows that DFT tends to overdelocalize the electrons in defected SrFeO 3 and LaFeO 3. Finally, calculations with DMC and local density approximation yield similar vacancy migration energy barriers, indicating that steric/electrostatic effects mainly determine migration barriers in these materials.« less

Impact of MPEG-4 3D mesh coding on watermarking algorithms for polygonal 3D meshes

NASA Astrophysics Data System (ADS)

Funk, Wolfgang

2004-06-01

The MPEG-4 multimedia standard addresses the scene-based composition of audiovisual objects. Natural and synthetic multimedia content can be mixed and transmitted over narrow and broadband communication channels. Synthetic natural hybrid coding (SNHC) within MPEG-4 provides tools for 3D mesh coding (3DMC). We investigate the robustness of two different 3D watermarking algorithms for polygonal meshes with respect to 3DMC. The first algorithm is a blind detection scheme designed for labelling applications that require high bandwidth and low robustness. The second algorithm is a robust non-blind one-bit watermarking scheme intended for copyright protection applications. Both algorithms have been proposed by Benedens. We expect 3DMC to have an impact on the watermarked 3D meshes, as the algorithms used for our simulations work on vertex coordinates to encode the watermark. We use the 3DMC implementation provided with the MPEG-4 reference software and the Princeton Shape Benchmark model database for our simulations. The watermarked models are sent through the 3DMC encoder and decoder, and the watermark decoding process is performed. For each algorithm under consideration we examine the detection properties as a function of the quantization of the vertex coordinates.

Application of a constant hole volume Sanchez-Lacombe equation of state to mixtures relevant to polymeric foaming.

PubMed

von Konigslow, Kier; Park, Chul B; Thompson, Russell B

2018-06-06

A variant of the Sanchez-Lacombe equation of state is applied to several polymers, blowing agents, and saturated mixtures of interest to the polymer foaming industry. These are low-density polyethylene-carbon dioxide and polylactide-carbon dioxide saturated mixtures as well as polystyrene-carbon dioxide-dimethyl ether and polystyrene-carbon dioxide-nitrogen ternary saturated mixtures. Good agreement is achieved between theoretically predicted and experimentally determined solubilities, both for binary and ternary mixtures. Acceptable agreement with swelling ratios is found with no free parameters. Up-to-date pure component Sanchez-Lacombe characteristic parameters are provided for carbon dioxide, dimethyl ether, low-density polyethylene, nitrogen, polylactide, linear and branched polypropylene, and polystyrene. Pure fluid low-density polyethylene and nitrogen parameters exhibit more moderate success while still providing acceptable quantitative estimations. Mixture estimations are found to have more moderate success where pure components are not as well represented. The Sanchez-Lacombe equation of state is found to correctly predict the anomalous reversal of solubility temperature dependence for low critical point fluids through the observation of this behaviour in polystyrene nitrogen mixtures.

Artemisia dracunculus L. polyphenols complexed to soy protein show enhanced bioavailability and hypoglycemic activity in C57BL/6 mice

PubMed Central

Ribnicky, D.M.; Roopchand, D.E.; Poulev, A; Kuhn, P.; Oren, A.; Cefalu, W.T.; Raskin, I.

2014-01-01

Objective Scientifically-validated food-based interventions are a practical means of addressing the epidemic of metabolic syndrome. An ethanolic extract of Artemisia dracunculus L. (PMI-5011) containing bioactive polyphenols, such as 2′, 4′–dihydroxy-4-methoxydihydrochalcone (DMC-2), improved insulin resistance in vitro and in vivo. Plant polyphenols are concentrated and stabilized when complexed to protein-rich matrices, such as soy protein isolate (SPI), which act as effective food-based delivery vehicles. In this study we compared bioaccessibility, bioavailability and efficacy of polyphenols extracted from A. dracunculus and delivered as PMI-5011 (ethanolic extract alone), formulated with the non-food excipient Gelucire®, (5011- Gelucire), or sorbed to SPI (5011-Nutrasorb®). Materials and Methods PMI-5011, 5011-Gelucire or 5011-Nutrasorb each containing 162 μg of DMC-2 was delivered to the TNO Intestinal Model-1 (TIM-1) of the human upper gastrointestinal tract to compare the effect of delivery vehicle on DMC-2 bioaccessibility. C57BL6/J mice were orally administered 5011-Nutrasorb or PMI-5011 to compare effects of polyphenol-protein complexation on acute hypoglycemic activity and bioavailability of DMC-2 in serum. Results At 500 mg/kg, 5011-Nutrasorb and PMI-5011 had similar hypoglycemic activity in high fat diet-induced diabetes mouse model despite the fact that 5011-Nutrasorb delivered 15-times less DMC-2 (40 μg/kg vs. 600 μg/kg). This can be partially explained by 8 times greater DMC-2 absorption into serum from 5011-Nutrasorb than from PMI-5011. TIM-1 experiments confirmed higher total bioaccessibility of DMC-2 in vitro when delivered in 5011-Nutrasorb (50.2 %) or Gelucire-5011 (44.4 %) compared to PMI-5011 (27.1 %) (p = 0.08). Conclusion Complexation with soy protein makes anti-diabetic A. dracunculus polyphenols more bioavailable and bioaccessible. PMID:24985105

Excess single-stranded DNA inhibits meiotic double-strand break repair.

PubMed

Johnson, Rebecca; Borde, Valérie; Neale, Matthew J; Bishop-Bailey, Anna; North, Matthew; Harris, Sheila; Nicolas, Alain; Goldman, Alastair S H

2007-11-01

During meiosis, self-inflicted DNA double-strand breaks (DSBs) are created by the protein Spo11 and repaired by homologous recombination leading to gene conversions and crossovers. Crossover formation is vital for the segregation of homologous chromosomes during the first meiotic division and requires the RecA orthologue, Dmc1. We analyzed repair during meiosis of site-specific DSBs created by another nuclease, VMA1-derived endonuclease (VDE), in cells lacking Dmc1 strand-exchange protein. Turnover and resection of the VDE-DSBs was assessed in two different reporter cassettes that can repair using flanking direct repeat sequences, thereby obviating the need for a Dmc1-dependent DNA strand invasion step. Access of the single-strand binding complex replication protein A, which is normally used in all modes of DSB repair, was checked in chromatin immunoprecipitation experiments, using antibody against Rfa1. Repair of the VDE-DSBs was severely inhibited in dmc1Delta cells, a defect that was associated with a reduction in the long tract resection required to initiate single-strand annealing between the flanking repeat sequences. Mutants that either reduce Spo11-DSB formation or abolish resection at Spo11-DSBs rescued the repair block. We also found that a replication protein A component, Rfa1, does not accumulate to expected levels at unrepaired single-stranded DNA (ssDNA) in dmc1Delta cells. The requirement of Dmc1 for VDE-DSB repair using flanking repeats appears to be caused by the accumulation of large quantities of ssDNA that accumulate at Spo11-DSBs when Dmc1 is absent. We propose that these resected DSBs sequester both resection machinery and ssDNA binding proteins, which in wild-type cells would normally be recycled as Spo11-DSBs repair. The implication is that repair proteins are in limited supply, and this could reflect an underlying mechanism for regulating DSB repair in wild-type cells, providing protection from potentially harmful effects of overabundant repair proteins.

Excess Single-Stranded DNA Inhibits Meiotic Double-Strand Break Repair

PubMed Central

Bishop-Bailey, Anna; North, Matthew; Harris, Sheila; Nicolas, Alain; Goldman, Alastair S. H

2007-01-01

During meiosis, self-inflicted DNA double-strand breaks (DSBs) are created by the protein Spo11 and repaired by homologous recombination leading to gene conversions and crossovers. Crossover formation is vital for the segregation of homologous chromosomes during the first meiotic division and requires the RecA orthologue, Dmc1.We analyzed repair during meiosis of site-specific DSBs created by another nuclease, VMA1-derived endonuclease (VDE), in cells lacking Dmc1 strand-exchange protein. Turnover and resection of the VDE-DSBs was assessed in two different reporter cassettes that can repair using flanking direct repeat sequences, thereby obviating the need for a Dmc1-dependent DNA strand invasion step. Access of the single-strand binding complex replication protein A, which is normally used in all modes of DSB repair, was checked in chromatin immunoprecipitation experiments, using antibody against Rfa1. Repair of the VDE-DSBs was severely inhibited in dmc1Δ cells, a defect that was associated with a reduction in the long tract resection required to initiate single-strand annealing between the flanking repeat sequences. Mutants that either reduce Spo11-DSB formation or abolish resection at Spo11-DSBs rescued the repair block. We also found that a replication protein A component, Rfa1, does not accumulate to expected levels at unrepaired single-stranded DNA (ssDNA) in dmc1Δ cells. The requirement of Dmc1 for VDE-DSB repair using flanking repeats appears to be caused by the accumulation of large quantities of ssDNA that accumulate at Spo11-DSBs when Dmc1 is absent. We propose that these resected DSBs sequester both resection machinery and ssDNA binding proteins, which in wild-type cells would normally be recycled as Spo11-DSBs repair. The implication is that repair proteins are in limited supply, and this could reflect an underlying mechanism for regulating DSB repair in wild-type cells, providing protection from potentially harmful effects of overabundant repair proteins. PMID:18081428

Mental illness, violence risk, and race in juvenile detention: implications for disproportionate minority contact.

PubMed

Desai, Rani A; Falzer, Paul R; Chapman, John; Borum, Randy

2012-01-01

Disproportionate minority contact (DMC) is a pervasive problem throughout the juvenile justice system. This article explored whether mental illness may be an explanatory factor in DMC. Data such as measures of violence risk and symptoms of mental illness were taken from intake interviews with 482 detained youth in Connecticut. Results indicated that racial minorities in detention have significantly lower violence risk than Caucasians but are disproportionately represented among detention populations relative to their proportions in the general population. In addition, DMC in these data was not explained by mental illness, seriousness of charges, violence risk, age, or gender. We suggest that mandated efforts to reduce DMC will need to address more than improving behavior or reducing symptoms of mental illness among detained minority youth. Instead, efforts should be focused on reducing the racial disparity evident in decisions made within the juvenile justice system. © 2012 American Orthopsychiatric Association.

Changing concentrations of CO, CH(4), C(5)H(8), CH(3)Br, CH(3)I, and dimethyl sulfide during the Southern Ocean Iron Enrichment Experiments.

PubMed

Wingenter, Oliver W; Haase, Karl B; Strutton, Peter; Friederich, Gernot; Meinardi, Simone; Blake, Donald R; Rowland, F Sherwood

2004-06-08

Oceanic iron (Fe) fertilization experiments have advanced the understanding of how Fe regulates biological productivity and air-sea carbon dioxide (CO(2)) exchange. However, little is known about the production and consumption of halocarbons and other gases as a result of Fe addition. Besides metabolizing inorganic carbon, marine microorganisms produce and consume many other trace gases. Several of these gases, which individually impact global climate, stratospheric ozone concentration, or local photochemistry, have not been previously quantified during an Fe-enrichment experiment. We describe results for selected dissolved trace gases including methane (CH(4)), isoprene (C(5)H(8)), methyl bromide (CH(3)Br), dimethyl sulfide, and oxygen (O(2)), which increased subsequent to Fe fertilization, and the associated decreases in concentrations of carbon monoxide (CO), methyl iodide (CH(3)I), and CO(2) observed during the Southern Ocean Iron Enrichment Experiments.

Rapid orthophoto development system.

DOT National Transportation Integrated Search

2013-06-01

The DMC system procured in the project represented state-of-the-art, large-format digital aerial camera systems at the start of : project. DMC is based on the frame camera model, and to achieve large ground coverage with high spatial resolution, the ...

Analysis of multi-year near-surface ozone observations at the WMO/GAW "Concordia" station (75°06‧S, 123°20‧E, 3280 m a.s.l. - Antarctica)

NASA Astrophysics Data System (ADS)

Cristofanelli, Paolo; Putero, Davide; Bonasoni, Paolo; Busetto, Maurizio; Calzolari, Francescopiero; Camporeale, Giuseppe; Grigioni, Paolo; Lupi, Angelo; Petkov, Boyan; Traversi, Rita; Udisti, Roberto; Vitale, Vito

2018-03-01

This work focuses on the near-surface O3 variability over the eastern Antarctic Plateau. In particular, eight years (2006-2013) of continuous observations at the WMO/GAW contributing station "Concordia" (Dome C-DMC: 75°06‧S, 123°20‧E, 3280 m) are presented, in the framework of the Italian Antarctic Research Programme (PNRA). First, the characterization of seasonal and diurnal O3 variability at DMC is provided. Then, for the period of highest data coverage (2008-2013), we investigated the role of specific atmospheric processes in affecting near-surface summer O3 variability, when O3 enhancement events (OEEs) are systematically observed at DMC (average monthly frequency peaking up to 60% in December). As deduced by a statistical selection methodology, these OEEs are affected by a significant interannual variability, both in their average O3 values and in their frequency. To explain part of this variability, we analyzed OEEs as a function of specific atmospheric variables and processes: (i) total column of O3 (TCO) and UV-A irradiance, (ii) long-range transport of air masses over the Antarctic Plateau (by Lagrangian back-trajectory analysis - LAGRANTO), (iii) occurrence of "deep" stratospheric intrusion events (by using the Lagrangian tool STLEFLUX). The overall near-surface O3 variability at DMC is controlled by a day-to-day pattern, which strongly points towards a dominating influence of processes occurring at "synoptic" scales rather than "local" processes. Even if previous studies suggested an inverse relationship between OEEs and TCO, we found a slight tendency for the annual frequency of OEEs to be higher when TCO values are higher over DMC. The annual occurrence of OEEs at DMC seems related to the total time spent by air masses over the Antarctic plateau before their arrival to DMC, suggesting the accumulation of photochemically-produced O3 during the transport, rather than a more efficient local production. Moreover, the identification of recent (i.e., 4-day old) stratospheric intrusion events by STEFLUX suggested only a minor influence (up to 3% of the period, in November) of "deep" events on the variability of near-surface summer O3 at DMC.

Volatile sulphur compounds in UHT milk.

PubMed

Al-Attabi, Z; D'Arcy, B R; Deeth, H C

2009-01-01

Several volatile sulphur compounds have been detected in raw and processed milk. These are hydrogen sulphide, methanethiol, carbonyl sulphide, dimethyl sulphide, carbon disulphide, dimethyl disulphide, dimethyl trisulphide, dimethyl sulphoxide, and dimethyl sulphone. Many of these increase in milk during heat processing and are associated with the cooked flavor of heat-treated milks, particularly UHT and sterilized milk. Several researchers have attempted to explain the origin of these volatiles in both raw and processed milk, and how to reduce the associated cooked flavor that has a negative impact on consumer acceptability of processed milk. These compounds are difficult to detect and analyze due to their high volatility, sensitivity to oxidation and heat, and in some cases, their very low concentrations. However, methods of detection and quantification have improved in recent years. Pre-concentration methods such as solid phase microextraction (SPME) together with gas chromatography equipped with sulphur-selective detectors now enable low concentrations of these compounds to be analyzed. In this review, methods of extraction and analyzes of these volatile sulphur compounds are compared, and their occurrence in milk is reviewed.

Process for biological material carbon-carbon bond formation

DOEpatents

Hollingsworth, R.I.; Jung, S.; Mindock, C.A.

1998-12-22

A process for providing vicinal dimethyl long chain between alkyl groups of organic compounds is described. The process uses intact or disrupted cells of various species of bacteria, particularly Thermoanaerobacter sp., Sarcina sp. and Butyrivibrio sp. The process can be conducted in an aqueous reaction mixture at room temperatures. 8 figs.

75 FR 57412 - Approval and Promulgation of Implementation Plans Alabama: Volatile Organic Compounds

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-21

...] Approval and Promulgation of Implementation Plans Alabama: Volatile Organic Compounds AGENCY: Environmental... compounds'' (VOCs) found at Alabama Administrative Code section 335-3-1-.02(gggg). Specifically, the revision would add two compounds (propylene carbonate and dimethyl carbonate) to the list of those excluded...

Process for biological material carbon-carbon bond formation

DOEpatents

Hollingsworth, Rawle I.; Jung, Seunho; Mindock, Carol A.

1998-01-01

A process for providing vicinal dimethyl long chain between alkyl groups of organic compounds is described. The process uses intact or disrupted cells of various species of bacteria, particularly Thermoanaerobacter sp., Sarcina sp. and Butyrivibrio sp. The process can be conducted in an aqueous reaction mixture at room temperatures.

Benchmarking the pseudopotential and fixed-node approximations in diffusion Monte Carlo calculations of molecules and solids

DOE PAGES

Nazarov, Roman; Shulenburger, Luke; Morales, Miguel A.; ...

2016-03-28

We performed diffusion Monte Carlo (DMC) calculations of the spectroscopic properties of a large set of molecules, assessing the effect of different approximations. In systems containing elements with large atomic numbers, we show that the errors associated with the use of nonlocal mean-field-based pseudopotentials in DMC calculations can be significant and may surpass the fixed-node error. In conclusion, we suggest practical guidelines for reducing these pseudopotential errors, which allow us to obtain DMC-computed spectroscopic parameters of molecules and equation of state properties of solids in excellent agreement with experiment.

Benchmarking the pseudopotential and fixed-node approximations in diffusion Monte Carlo calculations of molecules and solids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nazarov, Roman; Shulenburger, Luke; Morales, Miguel A.

We performed diffusion Monte Carlo (DMC) calculations of the spectroscopic properties of a large set of molecules, assessing the effect of different approximations. In systems containing elements with large atomic numbers, we show that the errors associated with the use of nonlocal mean-field-based pseudopotentials in DMC calculations can be significant and may surpass the fixed-node error. In conclusion, we suggest practical guidelines for reducing these pseudopotential errors, which allow us to obtain DMC-computed spectroscopic parameters of molecules and equation of state properties of solids in excellent agreement with experiment.

Sequence-Dependent Diastereospecific and Diastereodivergent Crosslinking of DNA by Decarbamoylmitomycin C.

PubMed

Aguilar, William; Paz, Manuel M; Vargas, Anayatzinc; Clement, Cristina C; Cheng, Shu-Yuan; Champeil, Elise

2018-04-20

Mitomycin C (MC), a potent antitumor drug, and decarbamoylmitomycin C (DMC), a derivative lacking the carbamoyl group, form highly cytotoxic DNA interstrand crosslinks. The major interstrand crosslink formed by DMC is the C1'' epimer of the major crosslink formed by MC. The molecular basis for the stereochemical configuration exhibited by DMC was investigated using biomimetic synthesis. The formation of DNA-DNA crosslinks by DMC is diastereospecific and diastereodivergent: Only the 1''S-diastereomer of the initially formed monoadduct can form crosslinks at GpC sequences, and only the 1''R-diastereomer of the monoadduct can form crosslinks at CpG sequences. We also show that CpG and GpC sequences react with divergent diastereoselectivity in the first alkylation step: 1"S stereochemistry is favored at GpC sequences and 1''R stereochemistry is favored at CpG sequences. Therefore, the first alkylation step results, at each sequence, in the selective formation of the diastereomer able to generate an interstrand DNA-DNA crosslink after the "second arm" alkylation. Examination of the known DNA adduct pattern obtained after treatment of cancer cell cultures with DMC indicates that the GpC sequence is the major target for the formation of DNA-DNA crosslinks in vivo by this drug. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Distributed Motor Controller (DMC) for Operation in Extreme Environments

NASA Technical Reports Server (NTRS)

McKinney, Colin M.; Yager, Jeremy A.; Mojarradi, Mohammad M.; Some, Rafi; Sirota, Allen; Kopf, Ted; Stern, Ryan; Hunter, Don

2012-01-01

This paper presents an extreme environment capable Distributed Motor Controller (DMC) module suitable for operation with a distributed architecture of future spacecraft systems. This motor controller is designed to be a bus-based electronics module capable of operating a single Brushless DC motor in extreme space environments: temperature (-120 C to +85 C required, -180 C to +100 C stretch goal); radiation (>;20K required, >;100KRad stretch goal); >;360 cycles of operation. Achieving this objective will result in a scalable modular configuration for motor control with enhanced reliability that will greatly lower cost during the design, fabrication and ATLO phases of future missions. Within the heart of the DMC lies a pair of cold-capable Application Specific Integrated Circuits (ASICs) and a Field Programmable Gate Array (FPGA) that enable its miniaturization and operation in extreme environments. The ASICs are fabricated in the IBM 0.5 micron Silicon Germanium (SiGe) BiCMOS process and are comprised of Analog circuitry to provide telemetry information, sensor interface, and health and status of DMC. The FPGA contains logic to provide motor control, status monitoring and spacecraft interface. The testing and characterization of these ASICs have yielded excellent functionality in cold temperatures (-135 C). The DMC module has demonstrated successful operation of a motor at temperature.

Effect of oxygen compounds addition on the hydrocracking of coal derived liquid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sato, Yoshiki; Kodera, Yoichi; Kamo, Tohru

1998-12-31

Coal derived liquid from liquefaction, coking and low temperature pyrolysis contains considerable amounts of alkylphenols with alkylbenzenes and alkylnaphthalenes. To produce and purify useful chemicals from coal-derived liquid, hydrocracking and hydrotreating of alkylphenol mixture is a very important process. In this study the effects of oxygen compounds such as dimethylcarbonate (DMC) addition on the hydrocracking of alkylphenols and coal-derived liquid were investigated to decrease hydrogen consumption due to the production of water from the removal of OH group. From the hydrocracking of 3,5-dimethylphenol (3,5-DMP) without DMC at 700 C, residence time of 3--10 sec under hydrogen-to-reactant molar ratio of moremore » than 10 using atmospheric flow apparatus with quartz reactor, m-xylene and m-cresol were produced with the production ratio of 1:1.8. However the dehydroxylation to produce m-xylene was decreased by the addition of 10% DMC with the 50% increased production ratio of 1:2.7. These are considered due to the strong interaction between OH group and DMC. Similar reaction behavior was observed in the hydrocracking of 2,5-DMP and the production ratio of (o-cresol + m-cresol)/p-xylene slightly increased from 3.0 to 3.5 by the addition of DMC. On the other hand, the products distribution did not change with and without DMC in the case of 2,6-DMP. This indicates the interaction is hindered by steric effect by the neighboring CH{sub 3} group. The effect of other oxygen compounds on the hydrocracking and the products distribution from the hydrocracking of coal-derived liquids is also discussed.« less

Rapid characterization of lithium ion battery electrolytes and thermal aging products by low-temperature plasma ambient ionization high-resolution mass spectrometry.

PubMed

Vortmann, Britta; Nowak, Sascha; Engelhard, Carsten

2013-03-19

Lithium ion batteries (LIBs) are key components for portable electronic devices that are used around the world. However, thermal decomposition products in the battery reduce its lifetime, and decomposition processes are still not understood. In this study, a rapid method for in situ analysis and reaction monitoring in LIB electrolytes is presented based on high-resolution mass spectrometry (HR-MS) with low-temperature plasma probe (LTP) ambient desorption/ionization for the first time. This proof-of-principle study demonstrates the capabilities of ambient mass spectrometry in battery research. LTP-HR-MS is ideally suited for qualitative analysis in the ambient environment because it allows direct sample analysis independent of the sample size, geometry, and structure. Further, it is environmental friendly because it eliminates the need of organic solvents that are typically used in separation techniques coupled to mass spectrometry. Accurate mass measurements were used to identify the time-/condition-dependent formation of electrolyte decomposition compounds. A LIB model electrolyte containing ethylene carbonate and dimethyl carbonate was analyzed before and after controlled thermal stress and over the course of several weeks. Major decomposition products identified include difluorophosphoric acid, monofluorophosphoric acid methyl ester, monofluorophosphoric acid dimethyl ester, and hexafluorophosphate. Solvents (i.e., dimethyl carbonate) were partly consumed via an esterification pathway. LTP-HR-MS is considered to be an attractive method for fundamental LIB studies.

Clinical assessment of decision-making capacity in acquired brain injury with personality change.

PubMed

Owen, Gareth S; Freyenhagen, Fabian; Martin, Wayne; David, Anthony S

2017-01-01

Assessment of decision-making capacity (DMC) can be difficult in acquired brain injury (ABI) particularly with the syndrome of organic personality disorder (OPD) (the "frontal lobe syndrome"). Clinical neuroscience may help but there are challenges translating its constructs to the decision-making abilities considered relevant by law and ethics. An in-depth interview study of DMC in OPD was undertaken. Six patients were purposefully sampled and rich interview data were acquired for scrutiny using interpretative phenomenological analysis. Interview data revealed that awareness of deficit and thinking about psychological states can be present. However, the awareness of deficit may not be "online" and effectively integrated into decision-making. Without this online awareness of deficit the ability to appreciate or use and weigh information in the process of deciding some matters appeared absent. We argue that the decision-making abilities discussed are: (1) necessary for DMC, (2) threatened by ABI , and (3) assessable at interview. Some advice for practically incorporating these abilities within assessments of DMC in patients with OPD is outlined.

Clinician perspectives on decision-making capacity after acquired brain injury.

PubMed

Mukherjee, Debjani; McDonough, Carol

2006-01-01

Acquired brain injury frequently alters an individual's ability to make health care decisions based on a clear understanding of the situation and options. This exploratory study investigated the ways health care providers address issues of decisionmaking capacity (DMC) on a daily, functional basis. 33 clinicians providing rehabilitation services to persons with acquired brain injury participated in 1 of 5 semi-structured focus groups. All 33 participants, representing 8 different occupations, agreed that DMC determinations affected their practice every day. Participants underscored a multidimensional rather than a unitary definition of DMC, with an emphasis on fluctuating capacities due to the injury. Important concerns were for the safety of the person with brain injury, the health care provider, and community members. Other themes included rehabilitation team involvement, family context, and professional socialization. Clinical determinations of DMC are context dependent and are affected by the abilities of the individual and the substance and consequences of the decision being made and include the concepts of regaining trust and reclaiming capacity.

Rapid analyses of dry matter content and carotenoids in fresh cassava roots using a portable visible and near infrared spectrometer (Vis/NIRS).

PubMed

Ikeogu, Ugochukwu N; Davrieux, Fabrice; Dufour, Dominique; Ceballos, Hernan; Egesi, Chiedozie N; Jannink, Jean-Luc

2017-01-01

Portable Vis/NIRS are flexible tools for fast and unbiased analyses of constituents with minimal sample preparation. This study developed calibration models for dry matter content (DMC) and carotenoids in fresh cassava roots using a portable Vis/NIRS system. We examined the effects of eight data pre-treatment combinations on calibration models and assessed calibrations on processed and intact root samples. We compared Vis/NIRS derived-DMC to other phenotyping methods. The results of the study showed that the combination of standard normal variate and de-trend (SNVD) with first derivative calculated on two data points and no smoothing (SNVD+1111) was adequate for a robust model. Calibration performance was higher with processed than the intact root samples for all the traits although intact root models for some traits especially total carotenoid content (TCC) (R2c = 96%, R2cv = 90%, RPD = 3.6 and SECV = 0.63) were sufficient for screening purposes. Using three key quality traits as templates, we developed models with processed fresh root samples. Robust calibrations were established for DMC (R2c = 99%, R2cv = 95%, RPD = 4.5 and SECV = 0.9), TCC (R2c = 99%, R2cv = 91%, RPD = 3.5 and SECV = 2.1) and all Trans β-carotene (ATBC) (R2c = 98%, R2cv = 91%, RPD = 3.5 and SECV = 1.6). Coefficient of determination on independent validation set (R2p) for these traits were also satisfactory for ATBC (91%), TCC (88%) and DMC (80%). Compared to other methods, Vis/NIRS-derived DMC from both intact and processed roots had very high correlation (>0.95) with the ideal oven-drying than from specific gravity method (0.49). There was equally a high correlation (0.94) between the intact and processed Vis/NIRS DMC. Therefore, the portable Vis/NIRS could be employed for the rapid analyses of DMC and quantification of carotenoids in cassava for nutritional and breeding purposes.

78 FR 19636 - Approval and Promulgation of Implementation Plans and Operating Permits Program; State of Missouri

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-02

... add the compounds propylene carbonate and dimethyl carbonate to the list of compounds which are excluded from the definition of Volatile Organic Compound (VOC) for consistency with the Federal definition... action. EPA will not institute a second comment period on this action. Any parties interested in...

Ketone EC50 values in the Microtox test.

PubMed

Chen, H F; Hee, S S

1995-03-01

The Microtox EC50 values for the following ketones are reported in the following homologous series: straight chain methyl ketones (acetone, 2-butanone, 2-pentanone, 2-hepatonone, 2-octanone, 2-decanone, and 2-tridecanone); methyl ketones substituted at one alpha carbon (3-methyl-2-butanone; 3,3-dimethyl-2-butanone); methyl substituted at two alpha carbons (2,4-dimethyl-3-pentanone; 2,2,4,4-tetramethyl-3-pentanone); phenyl groups replacing methyl in acetone (acetophenone; benzophenone); methyl groups substituted at the alpha carbons of cyclohexanone; and 2,3- 2,4-, and 2,5-hexanediones, most for the first time. While there were linear relationships between log EC50 and MW for the straight chain methyl ketones, and for methyl substitution at the alpha carbon for methyl ketones, there were no other linear relationships. As molecular weight increased, the EC50 values of soluble ketones decreased; as distance between two carbonyl groups decreased so too did EC50 values. Thus, for the ketones the geometry around the carbonyl group is an important determinant of toxicity as well as MW, water solubility, and octanol/water coefficient.

Some thoughts on GAIA and the sulfur cycle

NASA Technical Reports Server (NTRS)

Lovelock, J. E.

1985-01-01

The data hypothesis states that the composition, oxidation reduction state, and temperature of the troposphere are actively regulated by the biota for the biota. One of the early predictions of the Gaia hypothesis was that there should be a sulfur compound made by the biota in the oceans. It would need to be stable enough against oxidation in water to allow its transfer to the air. Either the sulfur compound itself or its atmospheric oxidation product would have to return sulfur from the sea to the land surfaces. The most likely candidate for this role was dimethyl sulfide. Another sulfur compound of interest from a Gaian viewpoint CS2 (carbon disulfide) is discussed. Theories on the production of dimethyl sulfide and carbon disulfide related to the Gaian hypothesis are examined.

Psychopathology, psychopharmacological properties, decision-making capacity to consent to clinical research and the willingness to participate among long-term hospitalized patients with schizophrenia.

PubMed

Wu, Bo-Jian; Liao, Hsun-Yi; Chen, Hsing-Kang; Lan, Tsuo-Hung

2016-03-30

Many studies discuss factors related to the decision-making capacity to consent to clinical research (DMC) of patients with schizophrenia. However, these studies rarely approached willingness to participate and the association between psychopharmacological properties (e.g., antipsychotic-induced side effects) and DMC. This study aimed to explore factors related to DMC and willingness to participate in patients with schizophrenia. All 139 patients with schizophrenia were assessed with the MacArthur Competence Assessment Tool for Clinical Research (MacCAT-CR) and other measures. A linear regression model was used to find the predictors of MacCAT-CR scores. A logistic regression model was used for exploring the predictors of willingness to participate. Patients with more severe negative symptoms performed poorly in DMC outcomes. In addition, females, those with fewer years of education and reduced cognitive function are more likely to experience difficulties in decision-making. Forty-three subjects (30.4%) chose to participate. Patients with higher level of positive symptoms, longer length of stay, higher burden of anticholinergics and users of atypical antipsychotics were more likely to participate in a clinical study which aimed to "enhance cognition". These finding suggest that research investigators should consider many variables for patients who require more intensive screening for impaired DMC. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Graft-transmissible movement of inverted-repeat-induced siRNA signals into flowers.

PubMed

Zhang, Wenna; Kollwig, Gregor; Stecyk, Ewelina; Apelt, Federico; Dirks, Rob; Kragler, Friedrich

2014-10-01

In plants, small interfering RNAs (siRNA) and microRNAs move to distant tissues where they control numerous developmental and physiological processes such as morphogenesis and stress responses. Grafting techniques and transient expression systems have been employed to show that sequence-specific siRNAs with a size of 21-24 nucleotides traffic to distant organs. We used inverted-repeat constructs producing siRNA targeting the meiosis factor DISRUPTED MEIOTIC cDNA 1 (DMC1) and GFP to test whether silencing signals move into meiotically active tissues. In grafted Nicotiana tabacum, a transgenic DMC1 siRNA signal made in source tissues preferably entered the anthers formed in the first flowers. Here, the DMC1 siRNA interfered with meiotic progression and, consequently, the flowers were at least partially sterile. In agro-infiltrated N. benthamiana plants, a GFP siRNA signal produced in leaves was allocated and active in most flower tissues including anthers. In hypocotyl-grafted Arabidopsis thaliana plants, the DMC1 silencing signal consistently appeared in leaves, petioles, and stem, and only a small number of plants displayed DMC1 siRNA signals in flowers. In all three tested plant species the systemic silencing signal penetrated male sporogenic tissues suggesting that plants harbour an endogenous long-distance small RNA transport pathway facilitating siRNA signalling into meiotically active cells. © 2014 The Authors The Plant Journal © 2014 John Wiley & Sons Ltd.

Diallel analysis of provitamin A carotenoid and dry matter content in cassava (Manihot esculenta Crantz)

PubMed Central

Esuma, Williams; Kawuki, Robert S.; Herselman, Liezel; Labuschagne, Maryke Tine

2016-01-01

Global efforts are underway to biofortify cassava (Manihot esculenta Crantz) with provitamin A carotenoids to help combat dietary vitamin A deficiency afflicting the health of more than 500 million resource-poor people in Sub-Saharan Africa. To further the biofortification initiative in Uganda, a 6×6 diallel analysis was conducted to estimate combining ability of six provitamin A clones and gene actions controlling total carotenoid content (TCC), dry matter content (DMC) in cassava roots and other relevant traits. Fifteen F1 families generated from the diallel crosses were evaluated in two environments using a randomized complete block design. General combining ability (GCA) effects were significant for TCC and DMC, suggesting the relative importance of additive gene effects in controlling these traits in cassava. On the other hand, non-additive effects were predominant for root and shoot weight. MH02-073HS, with the highest level of TCC, was the best general combiner for TCC while NASE 3, a popular white-fleshed variety grown by farmers in Uganda, was the best general combiner for DMC. Such progenitors with superior GCA effects could form the genetic source for future programs targeting cassava breeding for TCC and DMC. A negative correlation was observed between TCC and DMC, which will require breeding strategies to combine both traits for increased adoption of provitamin A cassava varieties. PMID:27795688

Using Spacecraft in Climate and Natural Disasters Registration

NASA Astrophysics Data System (ADS)

Sokol, Galyna; Kotlov, Vladyslav; Khorischenko, Oleksandr; Davydova, Angelica; Heti, Kristina

2017-04-01

Since the beginning of the space age it become possible the global monitoring of the planet Earth's state. Since the second half of the 20th century there are observations of the atmosphere's state and the Earth's climate have been held by a spacecraft. Also become possible large-scale monitoring of climate change. An attempt was made to define the role of infrasound in the interaction between a space weather, climate and biosphere of the Earth using spacecraft sensors recording. Many countries are involving in the detection of earthquakes, predicting volcanic eruptions and floods and also the monitoring of irregular solar activity. Understanding this leads to the conclusion that international cooperation for the protection of humanity is not only a political priority in the international arena, but also a question of the quality of living standards of any state. Commonly known following monitoring systems: Disaster Monitoring Constellation (DMC), FUEGO program (Spain), Sentinel-Asia program (Japan) and International aerospace system for monitoring of global phenomena (MAKCM, Russia). The Disaster Monitoring Constellation for International Imaging (DMCii) consists of a number of remote sensing satellites constructed by Surrey Satellite Technology Ltd (SSTL) and operated for the Algerian, Nigerian, Turkish, British and Chinese governments by DMC International Imaging. The DMC has monitored the effects and aftermath of the Indian Ocean Tsunami (December 2004), Hurricane Katrina (August 2005), and many other floods, fires and disasters. The individual DMC satellites are: 1. First generation satellites (AlSAT-1 - Algeria, BilSAT - Turkey, NigeriaSAT-1 - Nigeria, UK-DMC - United Kingdom); 2. Second generation satellites (Beijing - China, UK-DMC 2 - United Kingdom, Deimos-1 - Spanish commercial, NigeriaSAT-2 and NigeriaSAT-X). The sun-synchronous orbits of these satellites are coordinated so that the satellites follow each other around an orbital plane, ascending north over the Equator at 10:15 am local time (and 10:30 am local time for Beijing-1). Some of these satellites also include other imaging payloads and experimental payloads: onboard hardware-based image compression (on BilSAT), a GPS reflectometry experiment and onboard Internet router (on the UK-DMC satellite). The DMC satellites are notable for communicating with their ground stations using the Internet Protocol for payload data transfer and command and control, so extending the Internet into space, and allowing experiments with the Interplanetary Internet to be carried out. Many of the technologies used in the design of the DMC satellites, including Internet Protocol use, were tested in space beforehand on SSTL's earlier UoSAT-12 satellite. Currently, there is a great need to establish combining space and ground-based observation systems that will accurately capture key climate variables on a scale from regional to global and stable functioning for decades to determine climate variability and trends. With the help of modern computer systems were calculated moving of infrasonic waves in the atmosphere. This data can be used to predict the weather.

Volatile organic compounds as markers of quality changes during the storage of wild rocket.

PubMed

Luca, Alexandru; Kjær, Anders; Edelenbos, Merete

2017-10-01

The quality of leafy green vegetables changes during storage. Leaves become yellow or disintegrate, and an off-odor may develop. In addition, small amounts of volatile organic compounds (VOCs) are released. In this study, the release of acetone, carbon disulfide, dimethyl sulfide, nitromethane, pentane, 3-methylfuran, 2-ethylfuran, and dimethyl disulfide from wild rocket with different initial qualities was monitored during 8d storage at 10°C and correlated to aerobic bacteria counts, yeast and mold counts, and degree of tissue disintegration. The release of VOCs, except for 3-methylfuran, was influenced by the initial quality of the leaves. The release of pentane and 2-ethylfuran was related to the degree of tissue disintegration, and the release of dimethyl sulfide and dimethyl disulfide was related to the total aerobic bacteria count. The results demonstrated that VOCs can be used as markers for monitoring the complex quality changes taking place in packaged fresh produce during storage. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of Surface Oxygen on the Performance of Carbon as an Anode in Lithium-Ion Batteries

NASA Technical Reports Server (NTRS)

Hung, Ching-Cheh; Clark, Gregory W.

2001-01-01

Carbon materials with similar bulk structure but different surface oxygen were compared for their performance as anodes in lithium-ion battery. The bulk structure was such that the graphene planes were perpendicular to the surface. Three types of surfaces were examined: surface containing C=O type oxygen. surface containing -O-C type oxygen, and surface containing high concentration of active sites. The test involved cycles of lithium insertion into and release from the carbon materials, which was in the half cells of carbon/saturated LiI-50/50 (vol %) EC and DMC/lithium. During the first cycle of lithium insertion, the presence of adsorbed oxygen, -O-C type oxygen, active carbon sites, and C=O type oxygen resulted in the formation of solid-electrolyte interface (SEI) when the carbon's voltage relative to lithium metal was >1.35, 1 to 1.35, 0.5 to 1, and 0.67 to 0.7 V, respectively. An optimum -O-C type oxygen and a minimum C=O type oxygen was found to increase the reversible and decrease the irreversible capacity of carbon. Active sites on the carbon surface result in a large irreversible capacity and a second lithium insertion-release mechanism. However, this new mechanism has a short cycle life.

The Career Decision-Making Competence: A New Construct for the Career Realm

ERIC Educational Resources Information Center

Ceschi, Andrea; Costantini, Arianna; Phillips, Susan D.; Sartori, Riccardo

2017-01-01

Purpose: This paper aims to link findings from laboratory-based decision-making research and decision-making competence (DMC) aspects that may be central for career-related decision-making processes. Past research has identified individual differences in rational responses in decision situations, which the authors refer to as DMC. Although there…

The Importance of Electron Correlation on Stacking Interaction of Adenine-Thymine Base-Pair Step in B-DNA: A Quantum Monte Carlo Study.

PubMed

Hongo, Kenta; Cuong, Nguyen Thanh; Maezono, Ryo

2013-02-12

We report fixed-node diffusion Monte Carlo (DMC) calculations of stacking interaction energy between two adenine(A)-thymine(T) base pairs in B-DNA (AA:TT), for which reference data are available, obtained from a complete basis set estimate of CCSD(T) (coupled-cluster with singles, doubles, and perturbative triples). We consider four sets of nodal surfaces obtained from self-consistent field calculations and examine how the different nodal surfaces affect the DMC potential energy curves of the AA:TT molecule and the resulting stacking energies. We find that the DMC potential energy curves using the different nodes look similar to each other as a whole. We also benchmark the performance of various quantum chemistry methods, including Hartree-Fock (HF) theory, second-order Møller-Plesset perturbation theory (MP2), and density functional theory (DFT). The DMC and recently developed DFT results of the stacking energy reasonably agree with the reference, while the HF, MP2, and conventional DFT methods give unsatisfactory results.

Greater decision-making competence is associated with greater expected-value sensitivity, but not overall risk taking: an examination of concurrent validity.

PubMed

Parker, Andrew M; Weller, Joshua A

2015-01-01

Decision-making competence reflects individual differences in the susceptibility to committing decision-making errors, measured using tasks common from behavioral decision research (e.g., framing effects, under/overconfidence, following decision rules). Prior research demonstrates that those with higher decision-making competence report lower incidence of health-risking and antisocial behaviors, but there has been less focus on intermediate processes that may impact real-world decisions, and, in particular, those implicated by normative models. Here we test the associations between measures of youth decision-making competence (Y-DMC) and one such process, the degree to which individuals make choices consistent with maximizing expected value (EV). Using a task involving hypothetical gambles, we find that greater EV sensitivity is associated with greater Y-DMC. Higher Y-DMC scores are associated with (a) choosing risky options when EV favors those options and (b) avoiding risky options when EV favors a certain option. This relationship is stronger for gambles that involved potential losses. The results suggest that Y-DMC captures decision processes consistent with standard normative evaluations of risky decisions.

Linking Theoretical Decision-making Mechanisms in the Simon Task with Electrophysiological Data: A Model-based Neuroscience Study in Humans.

PubMed

Servant, Mathieu; White, Corey; Montagnini, Anna; Burle, Borís

2016-10-01

A current challenge for decision-making research is in extending models of simple decisions to more complex and ecological choice situations. Conflict tasks (e.g., Simon, Stroop, Eriksen flanker) have been the focus of much interest, because they provide a decision-making context representative of everyday life experiences. Modeling efforts have led to an elaborated drift diffusion model for conflict tasks (DMC), which implements a superimposition of automatic and controlled decision activations. The DMC has proven to capture the diversity of behavioral conflict effects across various task contexts. This study combined DMC predictions with EEG and EMG measurements to test a set of linking propositions that specify the relationship between theoretical decision-making mechanisms involved in the Simon task and brain activity. Our results are consistent with a representation of the superimposed decision variable in the primary motor cortices. The decision variable was also observed in the EMG activity of response agonist muscles. These findings provide new insight into the neurophysiology of human decision-making. In return, they provide support for the DMC model framework.

From Revolution to Evolution: 21 Years of the IRIS Data Management Facility

NASA Astrophysics Data System (ADS)

Benson, R. B.; Ahern, T. K.; Trabant, C. M.; Casey, R.

2009-12-01

A revolution is defined as a "drastic and far-reaching change in the way of thinking and behaving", and this describes the effect that the IRIS Data Management System (DMS) has had in the framework of seismological research. The IRIS Data Management Center (DMC) prototype began operation at theUniversity of Texas at Austin in 1988 and has evolved to to a fully functioning facility at the University of Washington in Seattle. The focus of this submission is to share an historical timeline of events related to the DMC, a bit of scrap-booking perhaps, centered around the business of waveform data management conducted by IRIS and it's partners. We hope to illustrate how the successful philosophy of sharing unrestricted data, openly collaborating with a global network of networks, and partnering with computer and software industry vendors that have supported our community's academic research, has enabled generations of seismologists to both curate and continually "mine" the ever-growing 45 years of digital data currently stored in the perpetual archive located in Seattle, WA. At the time that the Loma Prieta Earthquake shook and burned San Francisco on October 17, 1989, there were only 3 stations which had dial-up modems enabling what then was considered "fast access" to waveform data delivery from them back to the DMC. This was considered the first test of the DMC, since waveform data were collected and distributed within days of this event. But this was only a foretelling of things to come, since the rates of archiving and distribution have continually grown to a current 1900+ stations and a 17,000+ channel count of real-time data streaming in and out of the DMC daily, totaling 50 Terabytes of data shipped in 2009 alone. We will attempt to summarize the important technological challenges, solutions, and growth of the DMC with the goal of illustrating that "if you build it, they will come", and how this could be useful to other organizations.

Synthesis of carbon-11 labeled 1-(3,4-dimethoxybenzyl)-2,2-dimethyl-1,2,3,4-tetrahydroisoquinolinium derivatives as new potential PET SKCa channel imaging agents.

PubMed

Gao, Mingzhang; Wang, Min; Zheng, Qi-Huang

2008-02-01

Small conductance Ca2+-activated K+ (SKCa) channels play an important role in many functions such as neuronal communication and behavioral plasticity, secretion, and cell proliferation. SKCa channel modulation is associated with various brain, heart, and cancer diseases. N-methyl-laudanosine and its structurally related derivatives, substituted 1-(3,4-dimethoxybenzyl)-2,2-dimethyl-1,2,3,4-tetrahydroisoquinoliniums, are reversible and selective SKCa channel blockers. Carbon-11 labeled N-methyl-laudanosine and its tetrahydroisoquinolinium derivatives may serve as new probes for positron emission tomography (PET) to image SKCa channels in the brain, heart, and cancer. The key intermediates, substituted isoquinolines (3a-c), were synthesized using a modification of the Pomeranz-Fritsch procedure. The precursors, substituted 1-(3,4-dimethoxybenzyl)-2-methyl-1,2,3,4-tetrahydroisoquinolines (8a-c), and their corresponding reference standards, substituted 1-(3,4-dimethoxybenzyl)-2,2-dimethyl-1,2,3,4-tetrahydroisoquinoliniums (9a-c), were synthesized from compounds 3a-c with 3,4-dimethoxybenzyl chloride (2) in multiple steps with moderate to excellent chemical yields. The precursor 6,7-dimethoxy-1-(3,4-dimethoxybenzyl)-2-methyl-1,2,3,4-tetrahydroisoquinoline (10) was commercially available, and the methylation of compound 10 with methyl iodide provided N-methyl-laudanosine (11). The target quaternary ammonium tracers, carbon-11 labeled 1-(3,4-dimethoxybenzyl)-2,2-dimethyl-1,2,3,4-tetrahydroisoquinoliniums ([11C]9a-c and [11C]11), were prepared by N-[11C]methylation of the tertiary amine precursors (8a-c and 10) with [11C]methyl triflate and isolated by a simplified solid-phase extraction (SPE) purification using a SiO2 or cation-exchange CM Sep-Pak cartridge in 40-65% radiochemical yields.

Tobacco Stem-Based Activated Carbons for High Performance Supercapacitors

NASA Astrophysics Data System (ADS)

Xia, Xiaohong; Liu, Hongbo; Shi, Lei; He, Yuede

2012-09-01

Tobacco stem-based activated carbons (TS-ACs) were prepared by simple KOH activation and their application as electrodes in the electrical double layer capacitor (EDLC) performed successfully. The BET surface area, pore volume, and pore size distribution of the TS-ACs were evaluated based on N2 adsorption isotherms at 77 K. The surface area of the obtained activated carbons varies over a wide range (1472.8-3326.7 m2/g) and the mesoporosity was enhanced significantly as the ratio of KOH to tobacco stem (TS) increased. The electrochemical behaviors of series TS-ACs were characterized by means of galvanostatic charging/discharging, cyclic voltammetry, and impedance spectroscopy. The correlation between electrochemical properties and pore structure was investigated. A high specific capacitance value as 190 F/g at 1 mA/cm2 was obtained in 1 M LiPF6-EC/DMC/DEC electrolyte solution. Furthermore, good performance is also achieved even at high current densities. A development of new use for TS into a valuable energy storage material is explored.

MW-assisted synthesis of LiFePO 4 for high power applications

NASA Astrophysics Data System (ADS)

Beninati, Sabina; Damen, Libero; Mastragostino, Marina

LiFePO 4/C was prepared by solid-state reaction from Li 3PO 4, Fe 3(PO 4) 2·8H 2O, carbon and glucose in a few minutes in a scientific MW (microwave) oven with temperature and power control. The material was characterized by X-ray diffraction, scanning electron microscopy and by TGA analysis to evaluate carbon content. The electrochemical characterization as positive electrode in EC (ethylene carbonate)-DMC (dimethylcarbonate) 1 M LiPF 6 was performed by galvanostatic charge-discharge cycles at C/10 to evaluate specific capacity and by sequences of 10 s discharge-charge pulses, at different high C-rates (5-45C) to evaluate pulse-specific power in simulate operative conditions for full-HEV application. The maximum pulse-specific power and, particularly, pulse efficiency values are quite high and make MW synthesis a very promising route for mass production of LiFePO 4/C for full-HEV batteries at low energy costs.

Preparation and properties of dough-modeling compound/fly ash/reclaim powder composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, W.L.

A novel composite was prepared with reclaim powder (RP) matrix, dough-modeling compound (DMC) reinforcement and fly ash (FA) filler in this article. The compatibility and crosslinking construction of the FA/RP composites were respectively, studied by the polarizing microscope and IR, the optimal formulation and experimental process were determined by measuring the mechanical properties such as shore A hardness, tensile strength, elongation at break, wear resistance and the thermal stability. The results showed that DMC/FA/RP composites exhibited extremely high mechanical and thermal properties when the mass ratio of the DMC/FA/RP composites was 45/25/100, and the cure condition is at 145 {supmore » o}C for 30 min under 9 MPa.« less

Utilization of Dimethyl Sulfide as a Sulfur Source with the Aid of Light by Marinobacterium sp. Strain DMS-S1

PubMed Central

Fuse, Hiroyuki; Takimura, Osamu; Murakami, Katsuji; Yamaoka, Yukiho; Omori, Toshio

2000-01-01

Strain DMS-S1 isolated from seawater was able to utilize dimethyl sulfide (DMS) as a sulfur source only in the presence of light in a sulfur-lacking medium. Phylogenetic analysis based on 16S ribosomal DNA genes indicated that the strain was closely related to Marinobacterium georgiense. The strain produced dimethyl sulfoxide (DMSO), which was a main metabolite, and small amounts of formate and formaldehyde when grown on DMS as the sole sulfur source. The cells of the strain grown with succinate as a carbon source were able to use methyl mercaptan or methanesulfonate besides DMS but not DMSO or dimethyl sulfone as a sole sulfur source. DMS was transformed to DMSO primarily at wavelengths between 380 and 480 nm by heat-stable photosensitizers released by the strain. DMS was also degraded to formaldehyde in the presence of light by unidentified heat-stable factors released by the strain, and it appeared that strain DMS-S1 used the degradation products, which should be sulfite, sulfate, or methanesulfonate, as sulfur sources. PMID:11097944

Ultra Low-Cost Radar

NASA Astrophysics Data System (ADS)

Davies, P.; da Silva Curiel, A.; Eves, S.; Sweeting, M.; Thompson, A.; Hall, D.

From early 2003, Surrey Satellite Technology Limited (SSTL), together with its partners from Algeria, Nigeria and Turkey, has operated the Disaster Monitoring Constellation (DMC). During this period we have demonstrated the utility of a low-cost satellite system that uses optical sensors and is capable of providing daily imaging globally. For example, DMC data has been used operationally in the relief work in Darfur and following the Asian Tsunami. In addition to the use of the DMC to support disasters, the DMC has also been extensively used by the consortium members in support of national imaging needs and some residual system capacity has been provided to commercial customers. In the same timeframe, EADS Astrium Ltd has developed the technologies needed to implement the low-cost radar satellites of the MicroSAR range of synthetic aperture radar (SAR) satellites. EADS Astrium Ltd and SSTL are now looking to combine their expertises in low cost space technology and extend the capability of the DMC constellation by including a complementary small satellite radar sensor. The product of this activity is a satellite design that strikes an appropriate balance between revisit frequency and resolution. Hence, by comparison with other small satellite SAR concepts, the satellite described in this paper will provide broader area coverage at spatial resolutions in the region of 10 - 15m. Most significantly, perhaps, as a result of the specific cost targets imposed at the beginning of the design process, the satellite can provide this level of performance at a lower cost than other comparable space-based radar systems and significantly lower than larger, more performant, space-based radar systems.

Sufficient Amounts of Functional HOP2/MND1 Complex Promote Interhomolog DNA Repair but Are Dispensable for Intersister DNA Repair during Meiosis in Arabidopsis[W

PubMed Central

Uanschou, Clemens; Ronceret, Arnaud; Von Harder, Mona; De Muyt, Arnaud; Vezon, Daniel; Pereira, Lucie; Chelysheva, Liudmila; Kobayashi, Wataru; Kurumizaka, Hitoshi; Schlögelhofer, Peter; Grelon, Mathilde

2013-01-01

During meiosis, homologous recombination (HR) is essential to repair programmed DNA double-strand breaks (DSBs), and a dedicated protein machinery ensures that the homologous chromosome is favored over the nearby sister chromatid as a repair template. The HOMOLOGOUS-PAIRING PROTEIN2/MEIOTIC NUCLEAR DIVISION PROTEIN1 (HOP2/MND1) protein complex has been identified as a crucial factor of meiotic HR in Arabidopsis thaliana, since loss of either MND1 or HOP2 results in failure of DNA repair. We isolated two mutant alleles of HOP2 (hop2-2 and hop2-3) that retained the capacity to repair meiotic DSBs via the sister chromatid but failed to use the homologous chromosome. We show that in these alleles, the recombinases RADIATION SENSITIVE51 (RAD51) and DISRUPTED MEIOTIC cDNA1 (DMC1) are loaded, but only the intersister DNA repair pathway is activated. The hop2-2 phenotype is correlated with a decrease in HOP2/MND1 complex abundance. In hop2-3, a truncated HOP2 protein is produced that retains its ability to bind to DMC1 and DNA but forms less stable complexes with MND1 and fails to efficiently stimulate DMC1-driven D-loop formation. Genetic analyses demonstrated that in the absence of DMC1, HOP2/MND1 is dispensable for RAD51-mediated intersister DNA repair, while in the presence of DMC1, a minimal amount of functional HOP2/MND1 is essential to drive intersister DNA repair. PMID:24363313

Relationship between dry matter content at harvest and maturity index and post-harvest quality of "Fuji" apples

USDA-ARS?s Scientific Manuscript database

Two experiments were carried out to evaluate the relationship between dry matter content (DMC) and maturity index of ‘Fuji’ apple fruit sports (‘Mishima’, ‘Fuji Select’ and ‘Fuji Suprema’) during the final stage of fruit growth, and the relationship between DMC at harvest and the post-harvest fruit ...

ATMOSPHERIC CHEMISTRY OF SELECTED SULFUR-CONTAINING COMPOUNDS OUTDOOR SMOG CHAMBER STUDY - PHASE 1

EPA Science Inventory

The chemical behavior of hydrogen sulfide, carbonyl sulfide, carbon sulfide, methanethiol, ethanethiol, methyl sulfide, ethylsulfide, methyl-disulfide, ethyldisulfide, methylethylsulfide, thiophene, 2-methylthiophene, 3-methylthiophene, 2,5-dimethyl-thiophene and propene (used as...

Diffusion Monte Carlo calculations of Xenon and Krypton at High Pressure

NASA Astrophysics Data System (ADS)

Shulenburger, Luke; Mattsson, Thomas R.

2011-06-01

Ab initio calculations based on density functional theory (DFT) have proven a valuable tool in understanding the properties of materials at extreme conditions. However, there are entire classes of materials where the current limitations of DFT cast doubt upon the predictive power of the method. These include so called strongly correlated systems and materials where van der Waals forces are important. Diffusion Monte Carlo (DMC) can treat materials with a different class of approximations that have generally proven to be more accurate. The use of DMC together with DFT may therefore improve the predictive capability of the ab initio calculation of materials at extreme conditions. We present two examples of this approach. In the first we use DMC total energies to address the discrepancy between DFT and diamond anvil cell melt curves of Xe. In the second, DMC is used to address the choice of density functional used in calculations of the Kr hugoniot. Sandia National Laboratories is a multiprogram laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under Contract No. DE-AC04-94AL85000. Belonoshko et al. PRB 74, 054114 (2006).

The role of sulfur in osmoregulation and salinity tolerance in cyanobacteria, algae, and plants

NASA Technical Reports Server (NTRS)

Yopp, J. H.

1985-01-01

Organosulfur compounds are involved in osmoregulation and salinity tolerance in some cyanobacteria and photosynthetic eukaryotes. Glycinebetaine, the osmolyte of the halotolerant cyanobacterium, Aphanothece halophytica, requires the sulfonium compound. S-adenosyl-methionine (SAM) for its synthesis. Glutamate is the nitrogen source, SAM is the methyl carbon and serine the carbon backbone source of this unique osmolyte. Inhibitor studies suggest that photorespiration interacts with sulfur metabolism to control betaine synthesis in cyanobacteria. The limiting factor for SAM synthesis is formate from photorespiration. SAM is, in turn, the methyl donor for betaine synthesis from serine. The nitrogen component of serine is from glutamate. Betaine synthesis is hypothesized to be regulated via potassium. The biosynthesis of dimethyl-B-propiothetin (DMPT, which is the same as beta-dimethyl sulfonioprpionate) and diacylsulfoquinovosylglycerol were elucidated as having their roles in osmoregulation and salinity tolerance. The relation between these sulfolipids and the sulfur cycle was discussed.

Removal of dimethyl sulfide by the combination of non-thermal plasma and biological process.

PubMed

Wei, Z S; Li, H Q; He, J C; Ye, Q H; Huang, Q R; Luo, Y W

2013-10-01

A bench scale system integrated with a non-thermal plasma (NTP) and a biotricking filtration (BTF) unit for the treatment of gases containing dimethyl sulfide (DMS) was investigated. DMS removal efficiency in the integrated system was up to 96%. Bacterial communities in the BTF were assessed by PCR-DGGE, which play the dominant role in the biological processes of metabolism, sulfur oxidation, sulfate-reducing and carbon oxidation. The addition of ozone from NTP made microbial community in BTF more complicated and active for DMS removal. The NTP oxidize DMS to simple compounds such as methanol and carbonyl sulfide; the intermediate organic products and DMS are further oxidized to sulfate, carbon dioxide, water vapors by biological degradation. These results show that NTP-BTF is achievable and open new possibilities for applying the integrated with NTP and BTF to odour gas treatment. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

Dose-dependent changes of chemical attributes in irradiated sausages.

PubMed

Nam, K C; Lee, E J; Ahn, D U; Kwon, J H

2011-05-01

To determine the effects of irradiation on the chemical attributes of sausages, TBARS values, volatile compounds, gaseous compounds, and hydrocarbons of vacuum-packaged sausages were analyzed during 60 d of refrigerated storage. A sulfur-containing volatile (dimethyl disulfide), a gas (methane), and radiation-induced hydrocarbons (1-tetradecene, pentadecane, heptadecane, 8-heptadecene, eicosane, 1, 7-hexadecadiene, hexadecane) were mainly detected in irradiated sausages and the concentrations of these compounds were irradiation dose-dependent with R(2) = 0.9585, 0.9431, and 0.9091-0.9977, respectively. Especially methane and a few hydrocarbons were detected only in irradiated sausages and their amounts were dose-dependent. On the other hand, TBARS values, other off-odor volatiles (carbon disulfide, hexanal), and gases (carbon monoxide, carbon dioxide) were found both in irradiated and nonirradiated sausages. Therefore, it is suggested that radiation-induced hydrocarbons (1-tetradecene, pentadecane, heptadecane, 8-heptadecene, eicosane, 1, 7-hexadecadiene, hexadecane), dimethyl disulfide, and methane can be used as markers for irradiated sausages. Copyright © 2010 The American Meat Science Association. Published by Elsevier Ltd. All rights reserved.

Study of curcumin on microvasculature characteristic in diabetic rat's liver as revealed by vascular corrosion cast/scanning electron microscope (SEM) technique.

PubMed

Khimmaktong, Wipapan; Petpiboolthai, Hattaya; Panyarachun, Busaba; Anupunpisit, Vipavee

2012-05-01

To investigate the effect of curcumin on the structural change ofmicrovasculature in STZ-induced diabetic rat' liver. Diabetic rats were induced by streptozotocin (60 mg/kg BW). Male rats were divided into thre groups, control (C), diabetic (DM) and diabetic rats treated with curcumin (DMC) (200 mg/kg BW). After 8 weeks o experiments, blood vessels of rat's liver were studied under conventional light microscope (LM) and vascular corrosion cas technique with scanning electron microscope (SEM). LM observation demonstrated that there were pathology and destruction of liver tissues and microvasculature in diabetic animals. The sinusoids around central veins were dilated and filled with red blood cells. There was an accumulation of lipid droplets in the cytoplasm of hepatocytes and hepatocyte nuclei showed pathological sign of pyknosis. Moreover, the inflammation change of liver tissues revealed the infiltration of lymphocytes and increasing of collagen deposition in the area of portal triad. In curcumin-treated rats, the distinguished recovery of liver tissues showed regained normal pattern of central veins, sinusoids, hepatocytes and portal triad, when compared with liver tissues of control group. By using vascular corrosion casting with SEM, the liver blood vessels of DM group revealed higher and expanded sizes, compared with control group; proximal parts of portal veins (C = 577.75 +/- 126.23, DM = 892 +/- 35.79, DMC = 469.5 +/- 8553 microm), distal parts of portal veins (C = 76.72 +/- 1.48, DM = 200 +/- 31.05, DMC = 76.38 +/- 2.98 microm) and venules (C = 27.03 +/- 0.55, DM = 45.15 +/- 5.03, DMC = 28.38 +/- 3.67 microm) and corresponding to increased blood volumes compared with control group; proximal parts of portal veins (C = 20.8 +/- 1.28, DM = 62.2 +/- 3.39, DMC = 14.9 +/- 0.67 microm3), distal parts of portal veins (C = 0.46 +/- 0.03, DM = 3.81 +/- 0.18, DMC = 0.41 +/- 0.05 microm3) and venules (C = 0.05 +/- 0.05, DM = 0.24 +/- 0.013, DMC = 0.05 +/- 0.05 microm3) respectively. Fascinatingly, liver microvasculature in curcumin treated group developed into regenerate and repair into healthy and normal characteristics. Efficiency of curcumin treatment beneficially repaired and regenerated liver tissues of diabetic groups and also redeveloped the liver's microvascular complications. These results optimistically demonstrated the potential use of curcumin as a novel therapeutic agent in liver pathology of diabetic rats.

Chemical recycling of carbon dioxide to methanol and dimethyl ether: from greenhouse gas to renewable, environmentally carbon neutral fuels and synthetic hydrocarbons.

PubMed

Olah, George A; Goeppert, Alain; Prakash, G K Surya

2009-01-16

Nature's photosynthesis uses the sun's energy with chlorophyll in plants as a catalyst to recycle carbon dioxide and water into new plant life. Only given sufficient geological time can new fossil fuels be formed naturally. In contrast, chemical recycling of carbon dioxide from natural and industrial sources as well as varied human activities or even from the air itself to methanol or dimethyl ether (DME) and their varied products can be achieved via its capture and subsequent reductive hydrogenative conversion. The present Perspective reviews this new approach and our research in the field over the last 15 years. Carbon recycling represents a significant aspect of our proposed Methanol Economy. Any available energy source (alternative energies such as solar, wind, geothermal, and atomic energy) can be used for the production of needed hydrogen and chemical conversion of CO(2). Improved new methods for the efficient reductive conversion of CO(2) to methanol and/or DME that we have developed include bireforming with methane and ways of catalytic or electrochemical conversions. Liquid methanol is preferable to highly volatile and potentially explosive hydrogen for energy storage and transportation. Together with the derived DME, they are excellent transportation fuels for internal combustion engines (ICE) and fuel cells as well as convenient starting materials for synthetic hydrocarbons and their varied products. Carbon dioxide thus can be chemically transformed from a detrimental greenhouse gas causing global warming into a valuable, renewable and inexhaustible carbon source of the future allowing environmentally neutral use of carbon fuels and derived hydrocarbon products.

A density functional theory computational study of adsorption of Di-Meta-Cyano Azobenzene molecules on Si (111) surfaces

NASA Astrophysics Data System (ADS)

Motevalli, Benyamin; Taherifar, Neda; Wu, Bisheng; Tang, Wenxin; Liu, Jefferson Zhe

2017-11-01

The adsorption of di-meta-cyano azobenzene (DMC) cis and trans isomers on non-passivated and passivated Si (111) (7 × 7) surfaces is studied using density functional theory (DFT) calculations. Our results reveal that on the non-passivated surface the 12 Si adatoms are accessible to form chemical bonds with DMC molecules. Interestingly, the trans isomer forms two chemical bonds near the corner hole atom in Si (111) (7 × 7) surface, which is not observed in the widely studied metallic surfaces. The DMC isomers show significant structural distortion in the chemisorption case. The strong chemical bonds (and high bonding energy) could be detrimental to conformation switching between these two isomers under external stimuli. The physisorption case is also examined. Monte Carlo (MC) simulations with empirical force fields were employed to search about 106 different adsorption positions and DMC molecule orientations to identify the stable adsorption sites (up to six). The DFT-PBE and DFT-D2 calculations were then carried out to obtain the relaxed atomistic structures and accurate adsorption energy. We find that it is imperative to take van der Waals (vdW) interaction into account in DFT calculations. Our results show that the adsorption sites generally are encompassed by either the Si adatoms or the passivated H atoms, which could enhance the long-range dispersion interaction between DMC molecules and Si surfaces. The molecular structures of both isomers remain unchanged compared with gas phase. The obtained adsorption energy results ΔEads are moderate (0.2-0.8 eV). At some adsorption sites on the passivated surface, both isomers have similar moderate ΔEads (0.4-0.6 eV), implying promises of molecular switching that should be examined in experiments.

A systematic review of the reporting of Data Monitoring Committees' roles, interim analysis and early termination in pediatric clinical trials

PubMed Central

2009-01-01

Background Decisions about interim analysis and early stopping of clinical trials, as based on recommendations of Data Monitoring Committees (DMCs), have far reaching consequences for the scientific validity and clinical impact of a trial. Our aim was to evaluate the frequency and quality of the reporting on DMC composition and roles, interim analysis and early termination in pediatric trials. Methods We conducted a systematic review of randomized controlled clinical trials published from 2005 to 2007 in a sample of four general and four pediatric journals. We used full-text databases to identify trials which reported on DMCs, interim analysis or early termination, and included children or adolescents. Information was extracted on general trial characteristics, risk of bias, and a set of parameters regarding DMC composition and roles, interim analysis and early termination. Results 110 of the 648 pediatric trials in this sample (17%) reported on DMC or interim analysis or early stopping, and were included; 68 from general and 42 from pediatric journals. The presence of DMCs was reported in 89 of the 110 included trials (81%); 62 papers, including 46 of the 89 that reported on DMCs (52%), also presented information about interim analysis. No paper adequately reported all DMC parameters, and nine (15%) reported all interim analysis details. Of 32 trials which terminated early, 22 (69%) did not report predefined stopping guidelines and 15 (47%) did not provide information on statistical monitoring methods. Conclusions Reporting on DMC composition and roles, on interim analysis results and on early termination of pediatric trials is incomplete and heterogeneous. We propose a minimal set of reporting parameters that will allow the reader to assess the validity of trial results. PMID:20003383

Improved low temperature performance of lithium ion cells with quaternary carbonate-based electrolytes

NASA Technical Reports Server (NTRS)

Smart, M. C.; Ratnakumar, B. V.; Whitcanack, L. D.; Chin, K. B.; Surampudi, S.; Croft, H.; Tice, D.; Staniewicz, R.

2002-01-01

In order to enable future missions involving the exploration of the surface of Mars with Landers and Rovers, NASA desires long life, high energy density rechargeable batteries which can operate well at very low temperature (down to 40(deg)C). Lithium-ion technology has been identified as being the most promising chemistry, due to high gravimetric and volumetric energy densities, as well as, long life characteristics. However, the state-of-art (SOA) technology is not sufficient to meet the needs of many applications that require excellent low temperature capabilities. To further improve this technology, work at JF'L has been focused upon developing electrolytes that result in lithium-ion cells with wider temperature ranges of operation. These efforts have led to the identification of a number of ternary and quaternary, all carbonate-based electrolytes that have been demonstrated to result in improved low temperature performance in experimental three-electrode MCMB carbon/LiNio.sCoo.zOz cells. A number of electrochemical characterization techniques were performed on these cells (i.e., Tafel polarization measurements, linear polarization measurements, and electrochemical impedance spectroscopy (EIS)) to further enhance our understanding of the performance limitations at low temperature. The most promising electrolyte formulations, namely 1 .O M LiPF6EC+DEC+DMC+EMC (1 : 1: 1 :2 v/v) and 1 .O M LiPF6 EC+DEC+DMC+EMC (1 : 1 : 1 :3 v/v), were incorporated into SAFT prototype DD-size (9 Ahr) lithium- cells for evaluation. A number of electrical tests were performed on these cells, including rate characterization as a function of temperature, cycle life characterization at different temperatures, as well as, many mission specific characterization test to determine their viability to enable future missions to Mars. Excellent performance was observed with the prototype DD-size cells over a wide temperature range (-50 to 4OoC), with high specific energy being delivered at very low temperatures (i.e, over 95 WHrKg being delivered at 40(deg)C using a C/10 discharge rate).

When psychiatry and bioethics disagree about patient decision making capacity (DMC)

PubMed Central

Schneider, P L; Bramstedt, K A

2006-01-01

The terms “competency” and “decision making capacity” (DMC) are often used interchangeably in the medical setting. Although competency is a legal determination made by judges, “competency” assessments are frequently requested of psychiatrists who are called to consult on hospitalised patients who refuse medical treatment. In these situations, the bioethicist is called to consult frequently as well, sometimes as a second opinion or “tie breaker”. The psychiatric determination of competence, while a clinical phenomenon, is based primarily in legalism and can be quite different from the bioethics approach. This discrepancy highlights the difficulties that arise when a patient is found to be “competent” by psychiatry but lacking in DMC by bioethics. Using a case, this dilemma is explored and guidance for reconciling the opinions of two distinct clinical specialties is offered. PMID:16446413

DOE Office of Scientific and Technical Information (OSTI.GOV)

Azadi, Sam, E-mail: s.azadi@ucl.ac.uk; Cohen, R. E.; Department of Earth- and Environmental Sciences, Ludwig Maximilians Universität, Munich 80333

We studied the low-pressure (0–10 GPa) phase diagram of crystalline benzene using quantum Monte Carlo and density functional theory (DFT) methods. We performed diffusion quantum Monte Carlo (DMC) calculations to obtain accurate static phase diagrams as benchmarks for modern van der Waals density functionals. Using density functional perturbation theory, we computed the phonon contributions to the free energies. Our DFT enthalpy-pressure phase diagrams indicate that the Pbca and P2{sub 1}/c structures are the most stable phases within the studied pressure range. The DMC Gibbs free-energy calculations predict that the room temperature Pbca to P2{sub 1}/c phase transition occurs at 2.1(1)more » GPa. This prediction is consistent with available experimental results at room temperature. Our DMC calculations give 50.6 ± 0.5 kJ/mol for crystalline benzene lattice energy.« less

Secure Autonomous Automated Scheduling (SAAS). Rev. 1.1

NASA Technical Reports Server (NTRS)

Walke, Jon G.; Dikeman, Larry; Sage, Stephen P.; Miller, Eric M.

2010-01-01

This report describes network-centric operations, where a virtual mission operations center autonomously receives sensor triggers, and schedules space and ground assets using Internet-based technologies and service-oriented architectures. For proof-of-concept purposes, sensor triggers are received from the United States Geological Survey (USGS) to determine targets for space-based sensors. The Surrey Satellite Technology Limited (SSTL) Disaster Monitoring Constellation satellite, the UK-DMC, is used as the space-based sensor. The UK-DMC's availability is determined via machine-to-machine communications using SSTL's mission planning system. Access to/from the UK-DMC for tasking and sensor data is via SSTL's and Universal Space Network's (USN) ground assets. The availability and scheduling of USN's assets can also be performed autonomously via machine-to-machine communications. All communication, both on the ground and between ground and space, uses open Internet standards

Evaluating the viability of dimethyl carbonate as an alternative fuel for the transportation sector.

DOT National Transportation Integrated Search

2017-06-01

Some of the most important questions in the development of sustainable transportation are : identify fuels that will reduce emissions, provide diversification from fossil fuels, reduce : greenhouse gas emissions, be produced from renewable sources, a...

Fixed-node diffusion Monte Carlo potential energy curve of the fluorine molecule F{sub 2} using selected configuration interaction trial wavefunctions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giner, Emmanuel; Scemama, Anthony; Caffarel, Michel

2015-01-28

The potential energy curve of the F{sub 2} molecule is calculated with Fixed-Node Diffusion Monte Carlo (FN-DMC) using Configuration Interaction (CI)-type trial wavefunctions. To keep the number of determinants reasonable and thus make FN-DMC calculations feasible in practice, the CI expansion is restricted to those determinants that contribute the most to the total energy. The selection of the determinants is made using the CIPSI approach (Configuration Interaction using a Perturbative Selection made Iteratively). The trial wavefunction used in FN-DMC is directly issued from the deterministic CI program; no Jastrow factor is used and no preliminary multi-parameter stochastic optimization of themore » trial wavefunction is performed. The nodes of CIPSI wavefunctions are found to reduce significantly the fixed-node error and to be systematically improved upon increasing the number of selected determinants. To reduce the non-parallelism error of the potential energy curve, a scheme based on the use of a R-dependent number of determinants is introduced. Using Dunning’s cc-pVDZ basis set, the FN-DMC energy curve of F{sub 2} is found to be of a quality similar to that obtained with full configuration interaction/cc-pVQZ.« less

Outcomes of dual mobility cups in a young Middle Eastern population and its influence on life style.

PubMed

Assi, Chahine; El-Najjar, Elie; Samaha, Camille; Yammine, Kaissar

2017-03-01

Dual mobility cups (DMC) in total hip arthroplasty (THA) are becoming popular among orthopaedic surgeons. Substantial benefit of their use has been reported among high risk patients, particularly in reducing post-operative hip instability (dislocation). Many reports stated some concern when implanted in young and active people where complications such as polyethylene wear and mechanical loosening could potentially be higher. This Middle Eastern study analyses a retrospective series of THA for any aetiology other than infection, using DMC for the acetabular component in 75 patients (85 implants) less than 70 years old. No instability, intra-prosthetic dislocation or mechanical failure was reported during a mean follow-up of five years. The only major complication was a post-operative infection. The mean post- operative modified Harris hip score was 97.1 out of 100. All patients resumed their daily activities and all religious practicing patients were able to accomplish their prayer positions without pain. DMC is found to be an interesting option in reducing dislocation events in young patients. Those excellent short-term results would encourage surgeons to use DMC in an active and highly demanding population. Further research is necessary to confirm maintenance of such results at long term follow-up.

Catalytic ozonation of dimethyl phthalate over cerium supported on activated carbon.

PubMed

Li, Laisheng; Ye, Weiying; Zhang, Qiuyun; Sun, Fengqiang; Lu, Ping; Li, Xukai

2009-10-15

Cerium supported on activated carbon (Ce/AC), which was prepared by dipping method, was employed to degrade dimethyl phthalate (DMP) in water. The mineral matter present in the activated carbon positively contributes to its activity to enhance DMP ozonation process. A higher dipping Ce(NO(3))(3) concentration and calcination process increase its microporous volume and surface area, and decreases its exterior surface area. The catalytic activity reaches optimal when 0.2% (w/w) cerium is deposited on activated carbon. Ce/AC catalyst was characterized by XRD, SEM and BET. The presence of either activated carbon or Ce/AC catalyst considerably improves their degradation and mineralization in the ozonation of DMP. During the ozonation (50mg/h ozone flow rate) of a 30 mg/L DMP (initial pH 5.0) with the presence of Ce/AC catalyst, TOC removal rate reaches 68% at 60 min oxidation time, 48% using activated carbon as catalyst, only 22% with ozonation alone. The presence of tert-butanol (a well known OH radical scavenger) strongly inhibits DMP degradation by activated carbon or Ce/AC catalytic ozonation. TOC removal rate follows the second-order kinetics model well. In the ozonation of DMP with 50mg/h ozone flow rate, its mineralization rate constant with the presence of Ce/AC catalyst is 2.5 times higher than that of activated carbon, 7.5 times higher than that of O(3) alone. Ce/AC catalyst shows the better catalytic activity and stability based on 780 min sequential reaction in the ozonation of DMP. Ce/AC was a promising catalyst for ozonizing organic pollutants in the aqueous solution.

Tactical Operations Analysis Support Facility.

DTIC Science & Technology

1981-05-01

Punch/Reader 2 DMC-11AR DDCMP Micro Processor 2 DMC-11DA Network Link Line Unit 2 DL-11E Async Serial Line Interface 4 Intel IN-1670 448K Words MOS Memory...86 5.3 VIRTUAL PROCESSORS - VAX-11/750 ........................... 89 5.4 A RELATIONAL DATA MANAGEMENT SYSTEM - ORACLE...Central Processing Unit (CPU) is a 16 bit processor for high-speed, real time applications, and for large multi-user, multi- task, time shared

Blasting, graphical interfaces and Unix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knudsen, S.; Preece, D.S.

1993-11-01

A discrete element computer program, DMC (Distinct Motion Code) was developed to simulate blast-induced rock motion. To simplify the complex task of entering material and explosive design parameters as well as bench configuration, a full-featured graphical interface has been developed. DMC is currently executed on both Sun SPARCstation 2 and Sun SPARCstation 10 platforms and routinely used to model bench and crater blasting problems. This paper will document the design and development of the full-featured interface to DMC. The development of the interface will be tracked through the various stages, highlighting the adjustments made to allow the necessary parameters tomore » be entered in terms and units that field blasters understand. The paper also discusses a novel way of entering non-integer numbers and the techniques necessary to display blasting parameters in an understandable visual manner. A video presentation will demonstrate the graphics interface and explains its use.« less

Blasting, graphical interfaces and Unix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knudsen, S.; Preece, D.S.

1994-12-31

A discrete element computer program, DMC (Distinct Motion Code) was developed to simulate blast-induced rock motion. To simplify the complex task of entering material and explosive design parameters as well as bench configuration, a full-featured graphical interface has been developed. DMC is currently executed on both Sun SPARCstation 2 and Sun SPARCstation 10 platforms and routinely used to model bench and crater blasting problems. This paper will document the design and development of the full-featured interface to DMC. The development of the interface will be tracked through the various stages, highlighting the adjustments made to allow the necessary parameters tomore » be entered in terms and units that field blasters understand. The paper also discusses a novel way of entering non-integer numbers and the techniques necessary to display blasting parameters in an understandable visual manner. A video presentation will demonstrate the graphics interface and explains its use.« less

Virtual Mission Operations of Remote Sensors With Rapid Access To and From Space

NASA Technical Reports Server (NTRS)

Ivancic, William D.; Stewart, Dave; Walke, Jon; Dikeman, Larry; Sage, Steven; Miller, Eric; Northam, James; Jackson, Chris; Taylor, John; Lynch, Scott;

Economy of Standards: European Association of Urology Guideline Changes Influence Treatment Costs in Stage I Testicular Cancer Patients.

PubMed

John, Axel; Baumgart, André; Worst, Thomas; Heinzelbecker, Julia

2018-01-01

The study aimed to calculate direct medical costs (DMC) during the first year of diagnosis and to evaluate the impact of guideline changes on treatment costs in clinical stage (CS) I testicular germ cell tumor (TGCT) patients in a German healthcare system. Healthcare expenditures as DMC during the first year of diagnosis for 307 TGCT patients in CS I treated at our institution from 1987 to 2013 were calculated from the statutory health insurance perspective using patient level data. Three periods were defined referring to the first European Association of Urology (EAU) guideline in 2001 as well as to subsequent major guideline changes in 2005 and 2010. Data source for cost calculations were the German Diagnosis Related Groups system for inpatient stays (version 2014) and the German system for reimbursement of outpatient care (EBM - Einheitlicher Bewertungsmaßstab, edition 2014). During our 25 years of study period, mean DMC in the first year after diagnosis for the entire cohort of TGCT patients in CS I almost halved from EUR 13.000 to EUR 6.900 (p < 0.001). From 1987 to 2001, DMC for CS I seminomatous germ cell tumor (SGCT) patients were EUR 13.790 ± 4.700. From 2002 to 2010, mean costs were EUR 10.900 ± 5.990, and from 2011 to 2013, mean costs were EUR 5.190 ± 3.700. For CS I non-seminomatous germ cell tumor (NSGCT) patients, from 1987 to 2001, mean DMC were EUR 11.650 ± 5.690. From 2002 to 2010, mean costs were EUR 11.230 ± 5.990, and from 2011 to 2013, mean costs were EUR 11.170 ± 7.390. Follow-up examinations became less frequent over time, which caused a significant cost reduction for NSGCT (p = 0.042) while costs remained stable for SGCT. When adding costs of relapse treatment, active surveillance (AS) was the most cost-effective adjuvant treatment option in CS I NSGCT whereas one course carboplatin or AS caused similar expenditures in SGCT patients. The introduction of the EAU guidelines in 2001 caused a decrease in DMC in CS I seminoma patients. This cost reduction mainly took place due to the declining importance of radiation therapy. No substantial changes were seen in patients with CS I NSGCT. Costs for follow-up care also diminished, but to a lesser degree. Even when considering expenditures for relapse treatment, AS remained cost-effective in CS I TCGT patients. Our data show that evidence-based medicine in TGCT can reduce DMC in the first year after diagnosis. © 2018 S. Karger AG, Basel.

Research on the degradation mechanism of dimethyl phthalate in drinking water by strong ionization discharge

NASA Astrophysics Data System (ADS)

Hong, ZHAO; Chengwu, YI; Rongjie, YI; Huijuan, WANG; Lanlan, YIN; I, N. MUHAMMAD; Zhongfei, MA

2018-03-01

The degradation mechanism of dimethyl phthalate (DMP) in the drinking water was investigated using strong ionization discharge technology in this study. Under the optimized condition, the degradation efficiency of DMP in drinking water was up to 93% in 60 min. A series of analytical techniques including high-performance liquid chromatography, liquid chromatography mass spectrometry, total organic carbon analyzer and ultraviolet-visible spectroscopy were used in the study. It was found that a high concentration of ozone (O3) produced by dielectric barrier discharge reactor was up to 74.4 mg l-1 within 60 min. Tert-butanol, isopropyl alcohol, carbonate ions ({{{{CO}}}3}2-) and bicarbonate ions ({{{{HCO}}}3}-) was added to the sample solution to indirectly prove the presence and effect of hydroxyl radicals (·OH). These analytical findings indicate that mono-methyl phthalate, phthalic acid (PA) and methyl ester PA were detected as the major intermediates in the process of DMP degradation. Finally, DMP and all products were mineralized into carbon dioxide (CO2) and water (H2O) ultimately. Based on these analysis results, the degradation pathway of DMP by strong ionization discharge technology were proposed.

40 CFR Appendix - Tables to Part 132

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Bromophenyl phenyl ether Butyl benzyl phthalate Cadmium Carbon tetrachloride; tetrachloromethane Chlorobenzene...) phthalate Diazinon 1,2:5,6-Dibenzanthracene; dibenz[a,h]anthracene Dibutyl phthalate; di-n-butyl phthalate 1...-dichloropropylene Diethyl phthalate 2,4-Dimethylphenol; 2,4-xylenol Dimethyl phthalate 4,6-Dinitro-o-cresol; 2...

A study of perfluorocarboxylate ester solvents for lithium ion battery electrolytes

DOE PAGES

Fears, Tyler M.; Sacci, Robert L.; Winiarz, Jeffrey G.; ...

2015-09-18

We prepared several high-purity methyl perfluorocarboxylates (>99.5% purity by mole) and investigated as potential fluorine-rich electrolyte solvents in Li-ion batteries. The most conductive electrolyte, 0.1 M lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in dimethyl perfluoroglutarate (PF5M 2) (ionic conductivity 1.87 10 -2 mS cm -1), is investigated in Si thin-film half-cells. The solid-electrolyteinterphase (SEI) formed by the PF5M2 electrolyte is composed of similar organic and inorganic moieties and at comparable concentrations as those formed by ethylene carbonate/dimethyl carbonate electrolytes containing LiPF 6 and LiTFSI salts. But, the SEI formed by the PF5M 2 electrolyte undergoes reversible electrochemical defluorination, contributing to the reversible capacitymore » of the cell and compensating in part for capacity fade in the Si electrode. These electrolytes, though far from ideal, provide an opportunity to further develop predictions of suitable fluorinated molecules for use in battery solvents.« less

Folate Polyglutamylation Is Involved in Chromatin Silencing by Maintaining Global DNA Methylation and Histone H3K9 Dimethylation in Arabidopsis[C][W

PubMed Central

Zhou, Hao-Ran; Zhang, Fang-Fang; Ma, Ze-Yang; Huang, Huan-Wei; Jiang, Ling; Cai, Tao; Zhu, Jian-Kang; Zhang, Chuyi; He, Xin-Jian

2013-01-01

DNA methylation and repressive histone Histone3 Lysine9 (H3K9) dimethylation correlate with chromatin silencing in plants and mammals. To identify factors required for DNA methylation and H3K9 dimethylation, we screened for suppressors of the repressor of silencing1 (ros1) mutation, which causes silencing of the expression of the RD29A (RESPONSE TO DESSICATION 29A) promoter-driven luciferase transgene (RD29A-LUC) and the 35S promoter-driven NPTII (NEOMYCIN PHOSPHOTRANSFERASE II) transgene (35S-NPTII). We identified the folylpolyglutamate synthetase FPGS1 and the known factor DECREASED DNA METHYLATION1 (DDM1). The fpgs1 and ddm1 mutations release the silencing of both RD29A-LUC and 35S-NPTII. Genome-wide analysis indicated that the fpgs1 mutation reduces DNA methylation and releases chromatin silencing at a genome-wide scale. The effect of fpgs1 on chromatin silencing is correlated with reduced levels of DNA methylation and H3K9 dimethylation. Supplementation of fpgs1 mutants with 5-formyltetrahydrofolate, a stable form of folate, rescues the defects in DNA methylation, histone H3K9 dimethylation, and chromatin silencing. The competitive inhibitor of methyltransferases, S-adenosylhomocysteine, is markedly upregulated in fpgs1, by which fpgs1 reduces S-adenosylmethionine accessibility to methyltransferases and accordingly affects DNA and histone methylation. These results suggest that FPGS1-mediated folate polyglutamylation is required for DNA methylation and H3K9 dimethylation through its function in one-carbon metabolism. Our study makes an important contribution to understanding the complex interplay among metabolism, development, and epigenetic regulation. PMID:23881414

Surface modification and antimicrobial properties of cellulose nanocrystals

NASA Astrophysics Data System (ADS)

Bespalova, Yulia A.

Surface modification of cellulose nanocrystals (CNC) was performed by acetylation and subsequent reaction with various tertiary amines with different lengths of alkyl groups. Chloroacetic anhydride (95%) was used for acetylation. The acetylation of CNC was confirmed using IR spectroscopy. The bands associated with C=0 stretching (1740 cm-1) and C-Cl stretching (793 cm -1) was present in the acetylated CNC but they were absent in the neat CNC. It has been suggested that the primary hydroxyl groups of CNC are substituted by chloro acetyl groups during acetylation reaction. Subsequent reaction of chloro acetylated CNC with N, N - Dimethyl ethylamine, N, N - Dimethyl hexylamine, N, N - Dimethyl dodecylamine, N, N - Dimethyl hexadecylamine and N, N - Dimethyl decylamine formed quaternary ammonium salts. These quaternary ammonium salts were characterized by FTIR and solid state13C NMR spectroscopy. FTIR spectra of five types of quaternary ammonium salts of CNC are similar and they showed infrared bands at 2905 -1 and 2850 cm-1, attributed to symmetrical and unsymmetrical C-H stretching vibration. The absence of C-Cl band at 793 cm-1 proves that quaternary salt formation was successful. The 13C NMR spectrum of quaternary ammonium modified CNC with N, N - Dimethyl dodecylamine shows several additional resonances ranging from 14.5 ppm to 58.0 ppm when compared to 13C NMR spectrum of pure CNC. This evidence proves that long alkyl chains have been added to the pure CNC. The disc diffusion method confirmed that quaternary ammonium modified CNCs with a chain longer than ten carbons are effective antimicrobial agents against Staphylococcus aureus and E. coli bacteria. Pure CNC and quaternary ammonium modified CNCs with an alkyl chain length of ten or less were not able to inhibit bacteria growth.

Carbon dioxide conversion over carbon-based nanocatalysts.

PubMed

Khavarian, Mehrnoush; Chai, Siang-Piao; Mohamed, Abdul Rahman

2013-07-01

The utilization of carbon dioxide for the production of valuable chemicals via catalysts is one of the efficient ways to mitigate the greenhouse gases in the atmosphere. It is known that the carbon dioxide conversion and product yields are still low even if the reaction is operated at high pressure and temperature. The carbon dioxide utilization and conversion provides many challenges in exploring new concepts and opportunities for development of unique catalysts for the purpose of activating the carbon dioxide molecules. In this paper, the role of carbon-based nanocatalysts in the hydrogenation of carbon dioxide and direct synthesis of dimethyl carbonate from carbon dioxide and methanol are reviewed. The current catalytic results obtained with different carbon-based nanocatalysts systems are presented and how these materials contribute to the carbon dioxide conversion is explained. In addition, different strategies and preparation methods of nanometallic catalysts on various carbon supports are described to optimize the dispersion of metal nanoparticles and catalytic activity.

Intercalation of Lithium in Pitch-Based Graphitized Carbon Fibers Chemically Modified by Fluorine: Soft Carbon With or Without an Oxide Surface

NASA Technical Reports Server (NTRS)

Hung, Ching-Chen; Prisko, Aniko

1999-01-01

The effects of carbon structure and surface oxygen on the carbon's performance as the anode in lithium-ion battery were studied. Two carbon materials were used for the electrochemical tests: soft carbon made from defluorination of graphite fluoride, and the carbon precursor from which the graphite fluoride was made. In this research the precursor was graphitized carbon fiber P-100. It was first fluorinated to form CF(0.68), then defluorinated slowly at 350 to 450 C in bromoform, and finally heated in 1000 C nitrogen before exposed to room temperature air, producing disordered soft carbon having basic surface oxides. This process caused very little carbon loss. The electrochemical test involved cycles of lithium intercalation and deintercalation using C/saturated LiI-50/50 (vol %) EC and DMC/Li half cell. The cycling test had four major results. (1) The presence of a basic oxide surface may prevent solvent from entering the carbon structure and therefore prolong the carbon's cycle life for lithium intercalation-deintercalation. (2) The disordered soft carbon can store lithium through two different mechanisms. One of them is lithium intercalation. which gives the disordered carbon an electrochemical behavior similar to its more ordered graphitic precursor. The other is unknown in its chemistry, but is responsible for the high-N,oltage portion (less than 0.3V) of the charge-discharge curve. (3) Under certain conditions, the disordered carbon can store more lithium than its precursor. (4) These sample and its precursor can intercalate at 200 mA/g. and deintercalate at a rate of 2000 mA/g without significant capacity loss.

Independent academic Data Monitoring Committees for clinical trials in cardiovascular and cardiometabolic diseases.

PubMed

Filippatos, Gerasimos S; de Graeff, Pieter; Bax, Jeroen J; Borg, John-Joseph; Cleland, John G F; Dargie, Henry J; Flather, Marcus; Ford, Ian; Friede, Tim; Greenberg, Barry; Henon-Goburdhun, Cécile; Holcomb, Richard; Horst, Bradley; Lekakis, John; Mueller-Velten, Guenther; Papavassiliou, Athanasios G; Prasad, Krishna; Rosano, Giuseppe M C; Severin, Thomas; Sherman, Warren; Stough, Wendy Gattis; Swedberg, Karl; Tavazzi, Luigi; Tousoulis, Dimitris; Vardas, Panagiotis; Ruschitzka, Frank; Anker, Stefan D

2017-04-01

Data Monitoring Committees (DMCs) play a crucial role in the conducting of clinical trials to ensure the safety of study participants and to maintain a trial's scientific integrity. Generally accepted standards exist for DMC composition and operational conduct. However, some relevant issues are not specifically addressed in current guidance documents, resulting in uncertainties regarding optimal approaches for communication between the DMC, steering committee, and sponsors, release of information, and liability protection for DMC members. The Heart Failure Association (HFA) of the European Society of Cardiology (ESC), in collaboration with the Clinical Trials Unit of the European Heart Agency (EHA) of the ESC convened a meeting of international experts in DMCs for cardiovascular and cardiometabolic clinical trials to identify specific issues and develop steps to resolve challenges faced by DMCs.The main recommendations from the meeting relate to methodological consistency, independence, managing conflicts of interest, liability protection, and training of future DMC members. This paper summarizes the key outcomes from this expert meeting, and describes the core set of activities that might be further developed and ultimately implemented by the ESC, HFA, and other interested ESC constituent bodies. The HFA will continue to work with stakeholders in cardiovascular and cardiometabolic clinical research to promote these goals. © 2017 The Authors. European Journal of Heart Failure © 2017 European Society of Cardiology.

[Degradation of antipyrin by pyrazon-degrading bacteria (author's transl)].

PubMed

Sauber, K; Müller, R; Keller, E; Eberspächer, J; Lingens, F

1977-01-01

Bacteria with the ability to grow on pyrazon as sole source of carbon were isolated from soil. They also are able to grow on antipyrin. Then three metabolites of antipyrin can be isolated from the culture fluid which were identified as 2,3-dimethyl-1-(cis-2,3-dihydro-2,3-dihydroxy-4,6-cyclohexadiene-1-yl)-pyrazolone (5) (I), as 2,3-dimethyl-1-(2,3-dihydroxyphenyl)-pyrazolone (5) (II) and as 2,3-dimethyl-pyrazolone (5) (III), respectively. Compound I and II were used as substrates for enzyme studies. A dioxygenase catalyzes the enzymatic conversion of antipyrin into compound I. In the presence of NAD as cosubstrate compound I is transformed into compound II by a dehydrogenase. A pure preparation of metapyrocatechase from pyrazon-degrading bacteria converts compound II into the dephenylated heterocyclic moiety of antipyrin (III) and into 2-pyrone-6-carboxylic acid. Based on the results of the enzymatic studies a pathway for the degradation of antipyrin is proposed.

The 2007 water crisis in Wuxi, China: analysis of the origin.

PubMed

Zhang, Xiao-jian; Chen, Chao; Ding, Jian-qing; Hou, Aixin; Li, Yong; Niu, Zhang-bin; Su, Xiao-yan; Xu, Yan-juan; Laws, Edward A

2010-10-15

An odorous tap water crisis that affected two million residents for several days occurred in Wuxi, China in the summer of 2007. Volatile sulfide chemicals including methyl thiols, dimethyl sulfide, dimethyl disulfide, and dimethyl trisulfide were the dominant odorous contaminants in Lake Taihu and in tap water during the crisis. These contaminants originated from the decomposition of a massive cyanobacterial bloom that was triggered by illegal industrial discharges and inadequately regulated domestic pollution. A specific emergency drinking water treatment process was quickly developed using a combination of potassium permanganate oxidation and powdered activated carbon adsorption. The emergency treatment process removed the odor from the tap water and solved the crisis successfully in several days. This experience underscores the suggestion that a combination of stresses associated with eutrophication and industrial and domestic wastewater discharges can push an aquatic system to the tipping point with consequences far more severe than would occur if the system were subjected to each stress separately. 2010 Elsevier B.V. All rights reserved.

Kinetic and thermodynamic selectivity of intermolecular C-H activation at [Tp'Rh(PMe3)]. How does the ancillary ligand affect the metal-carbon bond strength?

PubMed

Jiao, Yunzhe; Morris, James; Brennessel, William W; Jones, William D

2013-10-30

Tp'Rh(PMe3)(CH3)H was synthesized as a precursor to produce the coordinatively unsaturated fragment [Tp'Rh(PMe3)], which reacts with benzene, mesitylene, 3,3-dimethyl-1-butene, 2-methoxy-2-methylpropane, 2-butyne, acetone, pentane, cyclopentane, trifluoroethane, fluoromethane, dimethyl ether, and difluoromethane at ambient temperature to give only one product in almost quantitative yield in each case. All of the complexes Tp'Rh(PMe3)(R)H were characterized by NMR spectroscopy, and their halogenated derivatives were fully characterized by NMR spectroscopy, elemental analysis, and X-ray crystallography. The active species [Tp'Rh(PMe3)] was also able to activate the alkynyl C-H bond of terminal alkynes to give activation products of the type Tp'Rh(PMe3)(C≡CR)H (R = t-Bu, SiMe3, hexyl, CF3, Ph, p-MeOC6H4, and p-CF3C6H4). The measured relative rhodium-carbon bond strengths display two linear correlations with the corresponding carbon-hydrogen bond strengths, giving a slope of 1.54 for α-unsubstituted hydrocarbons and a slope of 1.71 for substrates with α-substitution. Similar trends of energy correlations were established by DFT calculated metal-carbon bond strengths for the same groups of substrates.

Experience with Delay-Tolerant Networking from Orbit

NASA Technical Reports Server (NTRS)

Ivancic, W.; Eddy, W. M.; Stewart, D.; Wood, L.; Northam, J.; Jackson, C.

2010-01-01

We describe the first use from space of the Bundle Protocol for Delay-Tolerant Networking (DTN) and lessons learned from experiments made and experience gained with this protocol. The Disaster Monitoring Constellation (DMC), constructed by Surrey Satellite Technology Ltd (SSTL), is a multiple-satellite Earth-imaging low-Earth-orbit sensor network in which recorded image swaths are stored onboard each satellite and later downloaded from the satellite payloads to a ground station. Store-and-forward of images with capture and later download gives each satellite the characteristics of a node in a disruption-tolerant network. Originally developed for the Interplanetary Internet, DTNs are now under investigation in an Internet Research Task Force (IRTF) DTN research group (RG), which has developed a bundle architecture and protocol. The DMC is technically advanced in its adoption of the Internet Protocol (IP) for its imaging payloads and for satellite command and control, based around reuse of commercial networking and link protocols. These satellites use of IP has enabled earlier experiments with the Cisco router in Low Earth Orbit (CLEO) onboard the constellation s UK-DMC satellite. Earth images are downloaded from the satellites using a custom IP-based high-speed transfer protocol developed by SSTL, Saratoga, which tolerates unusual link environments. Saratoga has been documented in the Internet Engineering Task Force (IETF) for wider adoption. We experiment with the use of DTNRG bundle concepts onboard the UK-DMC satellite, by examining how Saratoga can be used as a DTN convergence layer to carry the DTNRG Bundle Protocol, so that sensor images can be delivered to ground stations and beyond as bundles. Our practical experience with the first successful use of the DTNRG Bundle Protocol in a space environment gives us insights into the design of the Bundle Protocol and enables us to identify issues that must be addressed before wider deployment of the Bundle Protocol. Published in 2010 by John Wiley & Sons, Ltd. KEY WORDS: Internet; UK-DMC; satellite; Delay-Tolerant Networking (DTN); Bundle Protocol

Advancements in Data Access at the IRIS Data Management Center to Broaden Data Use

NASA Astrophysics Data System (ADS)

Benson, R. B.; Trabant, C. M.; Ahern, T. K.

2013-12-01

The IRIS Data Management Center (DMC) has been serving digital seismic data for more than 20 years and has offered a variety of access mechanisms that have stood the test of time. However, beginning in 2010, and in response to multiple needs being requested from the IRIS DMC, we have developed web service interfaces to access our primary data repository. These new interfaces have rapidly grown in popularity. In 2013, the third full year of their operation, these services were responsible for half of all the data shipped from the DMC. In the same time period, the amount of data shipped from the other data access mechanisms has also increased. This non-linear growth of data shipments reflects the increased data usage by the research community. We believe that our new web service interfaces are well suited to fit future data access needs and signify a significant evolution in integrating different scientific data sets. Based on standardized web technologies, support for writing access software is ubiquitous. As fundamentally programmatic interfaces, the services are well suited for integration into data processing systems, in particular large-scale data processing systems. Their programmatic nature also makes then well suited for use with brokering systems where, for example, data from multiple disciplines can be integrated. In addition to providing access to raw data, the DMC created web services that apply simple, on-the-fly processing and format conversion. Processing the data (e.g. converting to Earth units) and formatting the result into something generally usable (e.g. ASCII) removes important barriers for users working in other disciplines. The end result is that we are shipping a much larger amount of data in a manner more directly usable by users. Many of these principles will be applied to the DMC's future work in the NSF's EarthCube Web Service Building Blocks project.

Effects of Type 2 Diabetes Mellitus in Patients on Treatment With Glibenclamide and Metformin on Carvedilol Enantiomers Metabolism.

PubMed

Nardotto, Glauco H B; Coelho, Eduardo B; Paiva, Carlos E; Lanchote, Vera L

2017-06-01

Carvedilol is available in clinical practice as a racemate in which (S)-(-)-carvedilol is a β- and α 1 -adrenergic antagonist and (R)-(+)-carvedilol is only an α 1 -adrenergic antagonist. Carvedilol is mainly metabolized by glucuronidation, by CYP2D6 to hydroxyphenylcarvedilol (OHC), and by CYP2C9 to O-desmethylcarvedilol (DMC). This study evaluated the pharmacokinetics of carvedilol enantiomers and their metabolites OHC and DMC in healthy volunteers (n = 13) and in type 2 diabetes mellitus patients with good glycemic control (n = 13). The healthy subjects were enrolled to receive either a 25-mg oral single dose of carvedilol alone (no DDI) or carvedilol simultaneously with 5 mg glibenclamide and 500 mg metformin (DDI), whereas type 2 diabetes mellitus patients who were on long-term treatment with glibenclamide (5 mg/8 h) and metformin (500 mg/8 h) were enrolled to receive only a single oral dose of 25 mg carvedilol. The plasma concentrations of the (R)-(+)-carvedilol, (R)-(+)-DMC, and (R)-(+)-OHC were higher than those of (S)-(-)-carvedilol, (S)-(-)-DMC, and (S)-(-)-OHC in all investigated groups. The pharmacokinetics of the carvedilol enantiomers did not differ between the groups. However, the AUC values of the DMC enantiomers were lower in the type 2 diabetes mellitus patients than in the healthy volunteers (DDI and no DDI) [(R)-(+), 6.9, 10.4, 11.9 ng·h/mL; and (S)-(-), 2.4, 4.3, 4.0 ng·h/mL, respectively]. In contrast, the AUC values of the OHC enantiomers were higher in the type 2 diabetes mellitus patients [(R)-(+), 13.9, 6.6, 4.9 ng·h/mL; and (S)-(-), 7.2, 1.5, 1.5 ng·h/mL], which explains the fact that the carvedilol pharmacokinetics was unchanged. © 2017, The American College of Clinical Pharmacology.

Mapping DNA adducts of mitomycin C and decarbamoyl mitomycin C in cell lines using liquid chromatography/electrospray tandem mass spectrometry

PubMed Central

Paz, Manuel M.; Ladwa, Sweta; Champeil, Elise; Liu, Yanfeng; Rockwell, Sara; Boamah, Ernest K.; Bargonetti, Jill; Callahan, John; Roach, John; Tomasz, Maria

2009-01-01

The antitumor antibiotic and cancer chemotherapeutic agent mitomycin C (MC) alkylates and cross-links DNA, forming six major MC-deoxyguanosine adducts of known structures in vitro and in vivo. Two of these adducts are derived from 2,7-diaminomitosene (2,7-DAM), a non-toxic reductive metabolite of MC formed in cells in situ. Several methods have been used for analysis of MC-DNA adducts in the past; however, a need exists for a safer, more comprehensive and direct assay of the six-adduct complex. Development of an assay, based on mass spectrometry is described. DNA from EMT6 mouse mammary tumor cells, Fanconi Anemia –A fibroblasts, normal human fibroblasts, and MCF-7 human breast cancer cells was isolated after MC or DMC treatment of the cells, digested to nucleosides and submitted to liquid chromatography electrospray-tandem mass spectrometry. Two fragments of each parent ion were monitored (“multiple reaction monitoring”; MRM). Identification and quantitative analysis was based on a standard mixture of six adducts, the preparation of which is described here in detail. The lower limit of detection of adducts is estimated as 0.25 picomol. Three initial applications of this method are reported: (i) differential kinetics of adduct repair in EMT6 cells; (ii) analysis of adducts in MC- or DMC-treated Fanconi Anemia cells; and (iii) comparison of the adducts generated by treatment of MCF-7 breast cancer cells with MC and DMC. Notable results are the following: repair removal of the DNA interstrand cross-link and of the two adducts of 2,7-DAM is relatively slow; both MC and DMC generate DNA interstrand cross-links in human fibroblasts, Fanconi Anemia-A fibroblasts and MCF-7 cells as well as EMT6 cells; DMC shows a stereochemical preference of linkage to the guanine-2-amino group opposite from that of MC. PMID:19053323

Mapping DNA adducts of mitomycin C and decarbamoyl mitomycin C in cell lines using liquid chromatography/ electrospray tandem mass spectrometry.

PubMed

Paz, Manuel M; Ladwa, Sweta; Champeil, Elise; Liu, Yanfeng; Rockwell, Sara; Boamah, Ernest K; Bargonetti, Jill; Callahan, John; Roach, John; Tomasz, Maria

2008-12-01

The antitumor antibiotic and cancer chemotherapeutic agent mitomycin C (MC) alkylates and crosslinks DNA, forming six major MC-deoxyguanosine adducts of known structures in vitro and in vivo. Two of these adducts are derived from 2,7-diaminomitosene (2,7-DAM), a nontoxic reductive metabolite of MC formed in cells in situ. Several methods have been used for the analysis of MC-DNA adducts in the past; however, a need exists for a safer, more comprehensive and direct assay of the six-adduct complex. Development of an assay, based on mass spectrometry, is described. DNA from EMT6 mouse mammary tumor cells, Fanconi Anemia-A fibroblasts, normal human fibroblasts, and MCF-7 human breast cancer cells was isolated after MC or 10-decarbamoyl mitomycin C (DMC) treatment of the cells, digested to nucleosides, and submitted to liquid chromatography electrospray-tandem mass spectrometry. Two fragments of each parent ion were monitored ("multiple reaction monitoring"). Identification and quantitative analysis were based on a standard mixture of six adducts, the preparation of which is described here in detail. The lower limit of detection of adducts is estimated as 0.25 pmol. Three initial applications of this method are reported as follows: (i) differential kinetics of adduct repair in EMT6 cells, (ii) analysis of adducts in MC- or DMC-treated Fanconi Anemia cells, and (iii) comparison of the adducts generated by treatment of MCF-7 breast cancer cells with MC and DMC. Notable results are the following: Repair removal of the DNA interstrand cross-link and of the two adducts of 2,7-DAM is relatively slow; both MC and DMC generate DNA interstrand cross-links in human fibroblasts, Fanconi Anemia-A fibroblasts, and MCF-7 cells as well as EMT6 cells; and DMC shows a stereochemical preference of linkage to the guanine-2-amino group opposite from that of MC.

Results from Preliminary Checks on AmBe Neutron Source Number 71

DTIC Science & Technology

2011-02-01

radiation and additional lead shielding was used to shield against gamma radiation emissions. Electronic dosimeters , the MGP DMC2000GN and Thermo EPD...DMC2000GN (S/N: 007395) and EPD-N2 (S/N: 07106323) electronic dosimeters were employed as these both are able to measure and record gamma and neutron...the AN/VDR-2 gamma radiation meter and Meridian Model 5085 neutron meter to confirm this and electronic dosimeters would be worn by personnel to

ASC Addresses Unit Commanders’ Concerns through LBE and Reset Programs

DTIC Science & Technology

2008-09-01

Distribution Management Center (DMC). The DMC, based at ASC Headquarters on Rock Island Arsenal, Ilinois, has become the single ASC integrator for LBE and field-level reset in support of ARFORGEN. The reset of units returning from OEF/OIF consists of a series of actions to restore the units to a desired level of combat capability commensurate with future mission requirements. These actions include the repair of equipment, replacement of equipment lost during operations, and recapitalization of equipment where feasible and

Relocation of the Deep Space Network Maintenance Center

NASA Technical Reports Server (NTRS)

Beutler, K. F.

1981-01-01

The Jet Propulsion Laboratory maintains a Deep Space Network (DSN) maintenance center (DMC), whose task is to engineer and manage the repair and calibration program for the electronic and mechanical equipment used in the tracking stations located at Madrid, Spain, and Canberra, Australia. The DMC also manages the Goldstone complex maintenance facility (GCMF), whose task is to repair and calibrate the Goldstone electronic and mechanical equipment. The rationale for moving the facility to Barstow, California, and the benefits derived from the move are discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lim, Chern -Hooi; Holder, Aaron M.; Hynes, James T.

Conflicting experimental results for the electrocatalytic reduction of CO 2 to CH 3OH on a glassy carbon electrode by the 6,7-dimethyl-4-hydroxy-2-mercaptopteridine have been recently reported. In this study, we have used computational chemistry to examine the issue of this molecule's ability to act as a hydride donor to reduce CO 2.

A New Epoxy Bis-Phosphonate Crosslinker for Durable Fire Retardancy on Cotton

USDA-ARS?s Scientific Manuscript database

A new epoxy bis-phosphonate crosslinker for cotton [2-(dimethoxy-phosphorylmethyl)-oxiranylmethyl]-phosphonic acid dimethyl ester was prepared in two steps from 3-chloro-2-chloromethylpropene in 55% yield. The new monomer was characterized by proton and carbon NMR and GC-mass spectrometry. This cro...

Equivalence of Brownian dynamics and dynamic Monte Carlo simulations in multicomponent colloidal suspensions.

PubMed

Cuetos, Alejandro; Patti, Alessandro

2015-08-01

We propose a simple but powerful theoretical framework to quantitatively compare Brownian dynamics (BD) and dynamic Monte Carlo (DMC) simulations of multicomponent colloidal suspensions. By extending our previous study focusing on monodisperse systems of rodlike colloids, here we generalize the formalism described there to multicomponent colloidal mixtures and validate it by investigating the dynamics in isotropic and liquid crystalline phases containing spherical and rodlike particles. In order to investigate the dynamics of multicomponent colloidal systems by DMC simulations, it is key to determine the elementary time step of each species and establish a unique timescale. This is crucial to consistently study the dynamics of colloidal particles with different geometry. By analyzing the mean-square displacement, the orientation autocorrelation functions, and the self part of the van Hove correlation functions, we show that DMC simulation is a very convenient and reliable technique to describe the stochastic dynamics of any multicomponent colloidal system. Our theoretical formalism can be easily extended to any colloidal system containing size and/or shape polydisperse particles.

Computing by robust transience: How the fronto-parietal network performs sequential category-based decisions

PubMed Central

Chaisangmongkon, Warasinee; Swaminathan, Sruthi K.; Freedman, David J.; Wang, Xiao-Jing

2017-01-01

Summary Decision making involves dynamic interplay between internal judgements and external perception, which has been investigated in delayed match-to-category (DMC) experiments. Our analysis of neural recordings shows that, during DMC tasks, LIP and PFC neurons demonstrate mixed, time-varying, and heterogeneous selectivity, but previous theoretical work has not established the link between these neural characteristics and population-level computations. We trained a recurrent network model to perform DMC tasks and found that the model can remarkably reproduce key features of neuronal selectivity at the single-neuron and population levels. Analysis of the trained networks elucidates that robust transient trajectories of the neural population are the key driver of sequential categorical decisions. The directions of trajectories are governed by network self-organized connectivity, defining a ‘neural landscape’, consisting of a task-tailored arrangement of slow states and dynamical tunnels. With this model, we can identify functionally-relevant circuit motifs and generalize the framework to solve other categorization tasks. PMID:28334612

Influence of various Activated Carbon based Electrode Materials in the Performance of Super Capacitor

NASA Astrophysics Data System (ADS)

Ajay, K. M.; Dinesh, M. N.

2018-02-01

Various activated carbon based electrode materials with different surface areas was prepared on stainless steel based refillable super capacitor model using spin coating. Bio Synthesized Activated Carbon (BSAC), Activated Carbon (AC) and Graphite powder are chosen as electrode materials in this paper. Electrode materials prepared using binder solution which is 6% by wt. polyvinylidene difluoride, 94% by wt. dimethyl fluoride. 3M concentrated KOH solution is used as aqueous electrolyte with PVDF thin film as separator. It is tested for electrochemical characterizations and material characterizations. It is observed that the Specific capacitance of Graphite, Biosynthesized active carbon and Commercially available activated carbon are 16.1F g-1, 53.4F g-1 and 107.6F g-1 respectively at 5mV s-1 scan rate.

Empirical Modeling of Nanoscale Dynamics using Solution Mapping

DTIC Science & Technology

2010-02-27

high performance liquid chromatography (HPLC). Journal of Supercritical Fluids , 44(2):139–147, 2008. 14 30 40 50 60 70 80 90 100 110 120 0 0.5 1 1.5...dioxide. Journal of Supercritical Fluids , 41(2):179–186, 2007. [3] O. Aschenbrenner, N. Dahmen, K. Schaber, and E. Dinjus. Adsorption of dimethyl(1,5...carbon nanotubes in a supercritical carbon dioxide process. The goal is to predict the time-evolution of the nanoparticle size distribution, as well

Highly crosslinked polyethylene: a safe alternative to conventional polyethylene for dual mobility cup mobile component. A biomechanical validation.

PubMed

Malatray, Matthieu; Roux, Jean-Paul; Gunst, Stanislas; Pibarot, Vincent; Wegrzyn, Julien

2017-03-01

Dual mobility cup (DMC) consists of a cobalt-chromium (CoCr) alloy cup articulated with a polyethylene (PE) mobile component capturing the femoral head in force using a snap-fit technique. This biomechanical study was the first to evaluate and compare the generation of cracks in the retentive area of DMC mobile components made of highly crosslinked PE (XLPE) or conventional ultra-high molecular weight PE (UHMWPE). Eighty mobile components designed for a 52-mm diameter Symbol® DMC (Dedienne Santé, Mauguio, France) and a 28-mm diameter femoral head were analyzed. Four groups of 20 mobile components were constituted according to the PE material: raw UHMWPE, sterilized UHMWPE, annealed XLPE and remelted XLPE. Ten mobile components in each group were impacted with a 28-mm diameter CoCr femoral head using a snap-fit technique. The occurrence, location and area of the cracks in the retentive area were investigated using micro-CT (Skyscan 1176®, Bruker, Aarsellar, Belgium) with a 35 μm nominal isotropic voxel size by two observers blinded to the PE material and impaction or not of the mobile components. Compared to conventional UHMWPE, the femoral head snap-fit did not generate more or wider cracks in the retentive area of annealed or remelted XLPE mobile components. This biomechanical study suggests that XLPE in DMC could be a safe alternative to conventional UHMWPE regarding the generation of cracks in the retentive area related to the femoral head snap-fit.

Differing Requirements for RAD51 and DMC1 in Meiotic Pairing of Centromeres and Chromosome Arms in Arabidopsis thaliana

PubMed Central

Da Ines, Olivier; Abe, Kiyomi; Goubely, Chantal; Gallego, Maria Eugenia; White, Charles I.

2012-01-01

During meiosis homologous chromosomes pair, recombine, and synapse, thus ensuring accurate chromosome segregation and the halving of ploidy necessary for gametogenesis. The processes permitting a chromosome to pair only with its homologue are not fully understood, but successful pairing of homologous chromosomes is tightly linked to recombination. In Arabidopsis thaliana, meiotic prophase of rad51, xrcc3, and rad51C mutants appears normal up to the zygotene/pachytene stage, after which the genome fragments, leading to sterility. To better understand the relationship between recombination and chromosome pairing, we have analysed meiotic chromosome pairing in these and in dmc1 mutant lines. Our data show a differing requirement for these proteins in pairing of centromeric regions and chromosome arms. No homologous pairing of mid-arm or distal regions was observed in rad51, xrcc3, and rad51C mutants. However, homologous centromeres do pair in these mutants and we show that this does depend upon recombination, principally on DMC1. This centromere pairing extends well beyond the heterochromatic centromere region and, surprisingly, does not require XRCC3 and RAD51C. In addition to clarifying and bringing the roles of centromeres in meiotic synapsis to the fore, this analysis thus separates the roles in meiotic synapsis of DMC1 and RAD51 and the meiotic RAD51 paralogs, XRCC3 and RAD51C, with respect to different chromosome domains. PMID:22532804

Ar(n)HF van der Waals clusters revisited: II. Energetics and HF vibrational frequency shifts from diffusion Monte Carlo calculations on additive and nonadditive potential-energy surfaces for n=1-12.

PubMed

Jiang, Hao; Xu, Minzhong; Hutson, Jeremy M; Bacić, Zlatko

2005-08-01

The ground-state energies and HF vibrational frequency shifts of Ar(n)HF clusters have been calculated on the nonadditive potential-energy surfaces (PESs) for n=2-7 and on the pairwise-additive PESs for the clusters with n=1-12, using the diffusion Monte Carlo (DMC) method. For n>3, the calculations have been performed for the lowest-energy isomer and several higher-lying isomers which are the closest in energy. They provide information about the isomer dependence of the HF redshift, and enable direct comparison with the experimental data recently obtained in helium nanodroplets. The agreement between theory and experiment is excellent, in particular, for the nonadditive DMC redshifts. The relative, incremental redshifts are reproduced accurately even at the lower level of theory, i.e., the DMC and quantum five-dimensional (rigid Ar(n)) calculations on the pairwise-additive PESs. The nonadditive interactions make a significant contribution to the frequency shift, on the order of 10%-12%, and have to be included in the PESs in order for the theory to yield accurate magnitude of the HF redshift. The energy gaps between the DMC ground states of the cluster isomers are very different from the energy separation of their respective minima on the PES, due to the considerable variations in the intermolecular zero-point energy of different Ar(n)HF isomers.

Lignin-based microporous materials as selective adsorbents for carbon dioxide separation.

PubMed

Meng, Qing Bo; Weber, Jens

2014-12-01

Suitable solid adsorbents are demanded for carbon capture and storage (CCS) processes. In this work, a novel microporous polymer is developed by hypercrosslinking of organosolv lignin, which is a renewable resource. Reaction with formaldehyde dimethyl acetal (FDA) via Friedel-Crafts reaction gives microporous networks, with moderate capacity of carbon dioxide but excellent selectivity towards CO2 /N2 mixture as predicted on the basis of ideal adsorption-solution theory (IAST). Pyrolysis of pure organosolv lignin results in microporous carbon powders, while pyrolysis of hypercrosslinked organosolv lignin yields shape-persistent materials with increased CO2 capacity while maintaining very good selectivity. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su, Liang; Ferrandon, Magali; Barton, John L.

The identification and development of conductive electrolytes with high concentrations of redox active species is key to realizing energy-dense nonaqueous flow batteries. Herein, we explore the use of ether solvents (1,3-dioxolane (DOL), 1,2-dimethoxyethane (DME), diethylene glycol dimethyl ether (DEGDME), and tetraethylene glycol dimethyl ether (TEGDME)) as the basis for redox electrolytes containing a lithium ion supporting salt (LiBF4 or LiTFSI) and 2,5-di-tert-butyl-1,4-bis(2-methoxyethoxy)benzene (DBBB) as an active material. An automated high-throughput platform is employed to screen various electrolyte compositions by measuring solution conductivity and solute solubility as a function of solvent and salt type, component concentration, and temperature. Subsequently, the electrochemicalmore » and transport properties of select redox electrolytes are characterized by cyclic voltammetry using glassy carbon disk electrodes and by linear sweep voltammetry using carbon fiber ultramicroelectrodes. In general, improvements in electrolyte conductivity and solute solubility are observed with ether-based formulations as compared to previously reported propylene carbonate (PC)-based formulations. In particular, the addition of DOL to a DME-based electrolyte increases the conductivity and decreases the temperature for solubilization at high LiTFSI and DBBB concentrations. The redox behavior of DBBB remains consistent across the range of concentrations tested while the diffusion coefficient scales with changes in solution viscosity.« less

Regioselective and enantiospecific rhodium-catalyzed allylic alkylation reactions using copper(I) enolates: synthesis of (-)-sugiresinol dimethyl ether.

PubMed

Evans, P Andrew; Leahy, David K

2003-07-30

The transition metal-catalyzed allylic alkylation represents a fundamentally important cross-coupling reaction for the construction of ternary carbon stereogenic centers. We have developed a regioselective and enantiospecific rhodium-catalyzed allylic alkylation of acyclic unsymmetrical allylic alcohol derivatives using copper(I) enolates to prepare beta-substituted ketones. This protocol represents a convenient asymmetric Claisen rearrangement surrogate in which alpha-substituted enolates permit the introduction of an additional stereogenic center. The synthetic utility of this transformation was highlighted in the construction of a trans-1,2-disubstituted cyclohexene and the total synthesis of (-)-sugiresinol dimethyl ether. Finally, we anticipate that copper(I) enolates may prove useful nucleophiles in related metal-catalyzed reactions.

Process for the production of ethylidene diacetate from dimethyl ether using a heterogeneous catalyst

DOEpatents

Ramprasad, D.; Waller, F.J.

1998-04-28

This invention relates to a process for producing ethylidene diacetate by the reaction of dimethyl ether, acetic acid, hydrogen and carbon monoxide at elevated temperatures and pressures in the presence of an alkyl halide and a heterogeneous, bifunctional catalyst that is stable to hydrogenation and comprises an insoluble polymer having pendant quaternized heteroatoms, some of which heteroatoms are ionically bonded to anionic Group VIII metal complexes, the remainder of the heteroatoms being bonded to iodide. In contrast to prior art processes, no accelerator (promoter) is necessary to achieve the catalytic reaction and the products are easily separated from the catalyst by filtration. The catalyst can be recycled for 3 consecutive runs without loss in activity.

Process for the production of ethylidene diacetate from dimethyl ether using a heterogeneous catalyst

DOEpatents

Ramprasad, Dorai; Waller, Francis Joseph

1998-01-01

This invention relates to a process for producing ethylidene diacetate by the reaction of dimethyl ether, acetic acid, hydrogen and carbon monoxide at elevated temperatures and pressures in the presence of an alkyl halide and a heterogeneous, bifunctional catalyst that is stable to hydrogenation and comprises an insoluble polymer having pendant quaternized heteroatoms, some of which heteroatoms are ionically bonded to anionic Group VIII metal complexes, the remainder of the heteroatoms being bonded to iodide. In contrast to prior art processes, no accelerator (promoter) is necessary to achieve the catalytic reaction and the products are easily separated from the catalyst by filtration. The catalyst can be recycled for 3 consecutive runs without loss in activity.

Emissions of Trace Gases and Particles from Savanna Fires in Southern Africa

NASA Technical Reports Server (NTRS)

Sinha, Parikhit; Hobbs, Peter V.; Yokelson, Robert J.; Bertschi, Isaac T.; Blake, Donald R.; Simpson, Isobel J.; Gao, Song; Kirchstetter, Thomas W.; Novakov, Tica

2003-01-01

Airborne measurements made on initial smoke from 10 savanna fires in southern Africa provide quantitative data on emissions of 50 gaseous and particulate species, including carbon dioxide, carbon monoxide, sulfur dioxide, nitrogen oxides, methane, ammonia, dimethyl sulfide, nonmethane organic compounds, halocarbons, gaseous organic acids, aerosol ionic components, carbonaceous aerosols, and condensation nuclei (CN). Measurements of several of the gaseous species by gas chromatography and Fourier transform infrared spectroscopy are compared. Emission ratios and emission factors are given for eight species that have not been reported previously for biomass burning of savanna in southern Africa (namely, dimethyl sulfide, methyl nitrate, five hydrocarbons, and particles with diameters from 0.1 to 3 microns). The emission factor that we measured for ammonia is lower by a factor of 4, and the emission factors for formaldehyde, hydrogen cyanide, and CN are greater by factors of about 3, 20, and 3 - 15, respectively, than previously reported values. The new emission factors are used to estimate annual emissions of these species from savanna fires in Africa and worldwide.

Superconcentrated electrolytes for a high-voltage lithium-ion battery

PubMed Central

Wang, Jianhui; Yamada, Yuki; Sodeyama, Keitaro; Chiang, Ching Hua; Tateyama, Yoshitaka; Yamada, Atsuo

2016-01-01

Finding a viable electrolyte for next-generation 5 V-class lithium-ion batteries is of primary importance. A long-standing obstacle has been metal-ion dissolution at high voltages. The LiPF6 salt in conventional electrolytes is chemically unstable, which accelerates transition metal dissolution of the electrode material, yet beneficially suppresses oxidative dissolution of the aluminium current collector; replacing LiPF6 with more stable lithium salts may diminish transition metal dissolution but unfortunately encounters severe aluminium oxidation. Here we report an electrolyte design that can solve this dilemma. By mixing a stable lithium salt LiN(SO2F)2 with dimethyl carbonate solvent at extremely high concentrations, we obtain an unusual liquid showing a three-dimensional network of anions and solvent molecules that coordinate strongly to Li+ ions. This simple formulation of superconcentrated LiN(SO2F)2/dimethyl carbonate electrolyte inhibits the dissolution of both aluminium and transition metal at around 5 V, and realizes a high-voltage LiNi0.5Mn1.5O4/graphite battery that exhibits excellent cycling durability, high rate capability and enhanced safety. PMID:27354162

Intracavity widely-tunable quantum cascade laser spectrometer.

PubMed

Brownsword, Richard A; Weidmann, Damien

2013-01-28

A grating-tuned extended-cavity quantum cascade laser (EC-QCL) operating around 7.6 µm was assembled to provide a tuning range of ~80 cm⁻¹ with output power of up to 30 mW. The EC-QCL output power was shown to be sensitive to the presence of a broadband absorbing gas mixture contained in a 2-cm cell introduced inside the extended laser cavity. In this arrangement, enhanced absorption relative to single path linear absorption was observed. To describe observations, in the QCL rate-equation model was included the effect of intracavity absorption. The model qualitatively reproduced the absorption behavior observed. In addition, it allowed quantitative measurements of mixing ratio of dimethyl carbonate, which was used as a test broadband absorber. A number of alternative data acquisition and reduction methods were identified. As the intracavity absorber modifies the laser threshold current, phase-sensitive detection of the laser threshold current was found to be the most attractive way to determine the mixing ratio of the absorber. The dimethyl carbonate detection limit was estimated to be 1.4 ppmv for 10 second integration. Limitations and possible ways of improvements were also identified.

Rapid determination of global moment-tensor solutions

USGS Publications Warehouse

Sipkin, S.A.

1994-01-01

In an effort to improve data services, the National Earthquake Information Center has begun a program, in cooperation with the Incorporated Research Institutions for Seismology Data Management Center (IRIS DMC), to produce rapid estimates of the seismic moment tensor for most earthquakes with a bodywave magnitude of 5.8 or greater. An estimate of the moment tensor can usually be produced within 20 minutes of the arrival of the broadband P-waveform data from the IRIS DMC. The solutions do not vary significantly from the final solutions determined using the entire network. -from Author

Web service activities at the IRIS DMC to support federated and multidisciplinary access

NASA Astrophysics Data System (ADS)

Trabant, Chad; Ahern, Timothy K.

2013-04-01

At the IRIS Data Management Center (DMC) we have developed a suite of web service interfaces to access our large archive of, primarily seismological, time series data and related metadata. The goals of these web services include providing: a) next-generation and easily used access interfaces for our current users, b) access to data holdings in a form usable for non-seismologists, c) programmatic access to facilitate integration into data processing workflows and d) a foundation for participation in federated data discovery and access systems. To support our current users, our services provide access to the raw time series data and metadata or conversions of the raw data to commonly used formats. Our services also support simple, on-the-fly signal processing options that are common first steps in many workflows. Additionally, high-level data products derived from raw data are available via service interfaces. To support data access by researchers unfamiliar with seismic data we offer conversion of the data to broadly usable formats (e.g. ASCII text) and data processing to convert the data to Earth units. By their very nature, web services are programmatic interfaces. Combined with ubiquitous support for web technologies in programming & scripting languages and support in many computing environments, web services are very well suited for integrating data access into data processing workflows. As programmatic interfaces that can return data in both discipline-specific and broadly usable formats, our services are also well suited for participation in federated and brokered systems either specific to seismology or multidisciplinary. Working within the International Federation of Digital Seismograph Networks, the DMC collaborated on the specification of standardized web service interfaces for use at any seismological data center. These data access interfaces, when supported by multiple data centers, will form a foundation on which to build discovery and access mechanisms for data sets spanning multiple centers. To promote the adoption of these standardized services the DMC has developed portable implementations of the software needed to host these interfaces, minimizing the work required at each data center. Within the COOPEUS project framework, the DMC is working with EU partners to install web services implementations at multiple data centers in Europe.

Real-time, autonomous precise satellite orbit determination using the global positioning system

NASA Astrophysics Data System (ADS)

Goldstein, David Ben

2000-10-01

The desire for autonomously generated, rapidly available, and highly accurate satellite ephemeris is growing with the proliferation of constellations of satellites and the cost and overhead of ground tracking resources. Autonomous Orbit Determination (OD) may be done on the ground in a post-processing mode or in real-time on board a satellite and may be accomplished days, hours or immediately after observations are processed. The Global Positioning System (GPS) is now widely used as an alternative to ground tracking resources to supply observation data for satellite positioning and navigation. GPS is accurate, inexpensive, provides continuous coverage, and is an excellent choice for autonomous systems. In an effort to estimate precise satellite ephemeris in real-time on board a satellite, the Goddard Space Flight Center (GSFC) created the GPS Enhanced OD Experiment (GEODE) flight navigation software. This dissertation offers alternative methods and improvements to GEODE to increase on board autonomy and real-time total position accuracy and precision without increasing computational burden. First, GEODE is modified to include a Gravity Acceleration Approximation Function (GAAF) to replace the traditional spherical harmonic representation of the gravity field. Next, an ionospheric correction method called Differenced Range Versus Integrated Doppler (DRVID) is applied to correct for ionospheric errors in the GPS measurements used in GEODE. Then, Dynamic Model Compensation (DMC) is added to estimate unmodeled and/or mismodeled forces in the dynamic model and to provide an alternative process noise variance-covariance formulation. Finally, a Genetic Algorithm (GA) is implemented in the form of Genetic Model Compensation (GMC) to optimize DMC forcing noise parameters. Application of GAAF, DRVID and DMC improved GEODE's position estimates by 28.3% when applied to GPS/MET data collected in the presence of Selective Availability (SA), 17.5% when SA is removed from the GPS/MET data and 10.8% on SA free TOPEX data. Position estimates with RSS errors below I meter are now achieved using SA free TOPEX data. DRVID causes an increase in computational burden while GAAF and DMC reduce computational burden. The net effect of applying GAAF, DRVID and DMC is an improvement in GEODE's accuracy/precision without an increase in computational burden.

Characterization and electrochemical application of carbon materials based on poly(phenylene oxide)

NASA Astrophysics Data System (ADS)

Gray, Hunter

Carbon materials possess excellent electrical and surface properties for the next generation of energy storage devices. Polymers provide a carbon rich and tailorable precursor for the production of carbon materials. Therefore, activated carbons were prepared from poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) via a three step process: thermal oxidation, carbonization, and activation with KOH. The activated carbons are predominately microporous with BET specific surface areas up to 2638 m2/g. Impedance spectroscopy revealed these carbons possess electrical conductivities comparable to commercial carbon blacks and consequently were employed in thin-film composite electrodes in electrochemical double-layer capacitors. Cyclic voltammetry confirmed maximum specific capacitances of 13.23 F/g and 2.848 F/g for aqueous and organic electrolyte systems, respectively. Additionally, carbon nanotubes were synthesized from PPO and other polymers with a nickel catalyst via chemical vapor deposition as revealed by transmission electron microscopy. This is the first report of carbon nanotubes produced from PPO.

Cyberinfrastructure at IRIS: Challenges and Solutions Providing Integrated Data Access to EarthScope and Other Earth Science Data

NASA Astrophysics Data System (ADS)

Ahern, T. K.; Barga, R.; Casey, R.; Kamb, L.; Parastatidis, S.; Stromme, S.; Weertman, B. T.

2008-12-01

While mature methods of accessing seismic data from the IRIS DMC have existed for decades, the demands for improved interdisciplinary data integration call for new approaches. Talented software teams at the IRIS DMC, UNAVCO and the ICDP in Germany, have been developing web services for all EarthScope data including data from USArray, PBO and SAFOD. These web services are based upon SOAP and WSDL. The EarthScope Data Portal was the first external system to access data holdings from the IRIS DMC using Web Services. EarthScope will also draw more heavily upon products to aid in cross-disciplinary data reuse. A Product Management System called SPADE allows archive of and access to heterogeneous data products, presented as XML documents, at the IRIS DMC. Searchable metadata are extracted from the XML and enable powerful searches for products from EarthScope and other data sources. IRIS is teaming with the External Research Group at Microsoft Research to leverage a powerful Scientific Workflow Engine (Trident) and interact with the web services developed at centers such as IRIS to enable access to data services as well as computational services. We believe that this approach will allow web- based control of workflows and the invocation of computational services that transform data. This capability will greatly improve access to data across scientific disciplines. This presentation will review some of the traditional access tools as well as many of the newer approaches that use web services, scientific workflow to improve interdisciplinary data access.

Fixed-Node Diffusion Quantum Monte Carlo Method on Dissociation Energies and Their Trends for R-X Bonds (R = Me, Et, i-Pr, t-Bu).

PubMed

Hou, Aiqiang; Zhou, Xiaojun; Wang, Ting; Wang, Fan

2018-05-15

Achieving both bond dissociation energies (BDEs) and their trends for the R-X bonds with R = Me, Et, i-Pr, and t-Bu reliably is nontrivial. Density functional theory (DFT) methods with traditional exchange-correlation functionals usually have large error on both the BDEs and their trends. The M06-2X functional gives rise to reliable BDEs, but the relative BDEs are determined not as accurately. More demanding approaches such as some double-hybrid functionals, for example, G4 and CCSD(T), are generally required to achieve the BDEs and their trends reliably. The fixed-node diffusion quantum Monte Carlo method (FN-DMC) is employed to calculated BDEs of these R-X bonds with X = H, CH 3 , OCH 3 , OH, and F in this work. The single Slater-Jastrow wave function is adopted as trial wave function, and pseudopotentials (PPs) developed for quantum Monte Carlo calculations are chosen. Error of these PPs is modest in wave function methods, while it is more pronounced in DFT calculations. Our results show that accuracy of BDEs with FN-DMC is similar to that of M06-2X and G4, and trends in BDEs are calculated more reliably than M06-2X. Both BDEs and trends in BDEs of these bonds are reproduced reasonably with FN-DMC. FN-DMC using PPs can thus be applied to BDEs and their trends of similar chemical bonds in larger molecules reliably and provide valuable information on properties of these molecules.

Moving Toward Real Time Data Handling: Data Management at the IRIS DMC

NASA Astrophysics Data System (ADS)

Ahern, T. K.; Benson, R. B.

2001-12-01

The IRIS Data Management Center at the University of Washington has become a major archive and distribution center for a wide variety of seismological data. With a mass storage system with a 360-terabyte capacity, the center is well positioned to manage the data flow, both inbound and outbound, from all anticipated seismic sources for the foreseeable future. As data flow in and out of the IRIS DMC at an increasing rate, new methods to deal with data using purely automated techniques are being developed. The on-line and self-service data repositories of SPYDERr and FARM are collections of seismograms for all larger events. The WWW tool WILBER and the client application WEED are examples of tools that provide convenient access to the 1/2 terabyte of SPYDERr and FARM data. The Buffer of Uniform Data (BUD) system provides access to continuous data available in real time from GSN, FDSN, US regional networks, and other globally distributed stations. Continuous data that have received quality control are always available from the archive of continuous data. This presentation will review current and future data access techniques supported at IRIS. One of the most difficult tasks at the DMC is the management of the metadata that describes all the stations, sensors, and data holdings. Demonstrations of tools that provide access to the metadata will be presented. This presentation will focus on the new techniques of data management now being developed at the IRIS DMC. We believe that these techniques are generally applicable to other types of geophysical data management as well.

Integrated health management and control of complex dynamical systems

NASA Astrophysics Data System (ADS)

Tolani, Devendra K.

2005-11-01

A comprehensive control and health management strategy for human-engineered complex dynamical systems is formulated for achieving high performance and reliability over a wide range of operation. Results from diverse research areas such as Probabilistic Robust Control (PRC), Damage Mitigating/Life Extending Control (DMC), Discrete Event Supervisory (DES) Control, Symbolic Time Series Analysis (STSA) and Health and Usage Monitoring System (HUMS) have been employed to achieve this goal. Continuous-domain control modules at the lower level are synthesized by PRC and DMC theories, whereas the upper-level supervision is based on DES control theory. In the PRC approach, by allowing different levels of risk under different flight conditions, the control system can achieve the desired trade off between stability robustness and nominal performance. In the DMC approach, component damage is incorporated in the control law to reduce the damage rate for enhanced structural durability. The DES controller monitors the system performance and, based on the mission requirements (e.g., performance metrics and level of damage mitigation), switches among various lower-level controllers. The core idea is to design a framework where the DES controller at the upper-level, mimics human intelligence and makes appropriate decisions to satisfy mission requirements, enhance system performance and structural durability. Recently developed tools in STSA have been used for anomaly detection and failure prognosis. The DMC deals with the usage monitoring or operational control part of health management, where as the issue of health monitoring is addressed by the anomaly detection tools. The proposed decision and control architecture has been validated on two test-beds, simulating the operations of rotorcraft dynamics and aircraft propulsion.

Negative decision outcomes are more common among people with lower decision-making competence: an item-level analysis of the Decision Outcome Inventory (DOI).

PubMed

Parker, Andrew M; Bruine de Bruin, Wändi; Fischhoff, Baruch

2015-01-01

Most behavioral decision research takes place in carefully controlled laboratory settings, and examination of relationships between performance and specific real-world decision outcomes is rare. One prior study shows that people who perform better on hypothetical decision tasks, assessed using the Adult Decision-Making Competence (A-DMC) measure, also tend to experience better real-world decision outcomes, as reported on the Decision Outcomes Inventory (DOI). The DOI score reflects avoidance of outcomes that could result from poor decisions, ranging from serious (e.g., bankruptcy) to minor (e.g., blisters from sunburn). The present analyses go beyond the initial work, which focused on the overall DOI score, by analyzing the relationships between specific decision outcomes and A-DMC performance. Most outcomes are significantly more likely among people with lower A-DMC scores, even after taking into account two variables expected to produce worse real-world decision outcomes: younger age and lower socio-economic status. We discuss the usefulness of DOI as a measure of successful real-world decision-making.

Performance of quantum Monte Carlo for calculating molecular bond lengths

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cleland, Deidre M., E-mail: deidre.cleland@csiro.au; Per, Manolo C., E-mail: manolo.per@csiro.au

2016-03-28

This work investigates the accuracy of real-space quantum Monte Carlo (QMC) methods for calculating molecular geometries. We present the equilibrium bond lengths of a test set of 30 diatomic molecules calculated using variational Monte Carlo (VMC) and diffusion Monte Carlo (DMC) methods. The effect of different trial wavefunctions is investigated using single determinants constructed from Hartree-Fock (HF) and Density Functional Theory (DFT) orbitals with LDA, PBE, and B3LYP functionals, as well as small multi-configurational self-consistent field (MCSCF) multi-determinant expansions. When compared to experimental geometries, all DMC methods exhibit smaller mean-absolute deviations (MADs) than those given by HF, DFT, and MCSCF.more » The most accurate MAD of 3 ± 2 × 10{sup −3} Å is achieved using DMC with a small multi-determinant expansion. However, the more computationally efficient multi-determinant VMC method has a similar MAD of only 4.0 ± 0.9 × 10{sup −3} Å, suggesting that QMC forces calculated from the relatively simple VMC algorithm may often be sufficient for accurate molecular geometries.« less

Study on the Treatment of Wastewater Generated at KSC (Kennedy Space Center) STS (Space Transport System) Operations and Projected Effects on the Design of the STS Hazardous Waste Management Facility at Vandenberg AFB, California.

DTIC Science & Technology

1983-10-01

carbon monoxide gas (mostly converted to carbon dioxide during afterburning), alu- minum oxide particles, and hydrogen chloride gas. Additionally, a great...colorimetrically or with an oxidation -reduction probe (ORP). The laboratory tests used a colorimetric indi- cator N.N.-Dimethyl-P-Phenylene Diamine Sulfate...in the composite wastewater sample under both quiescent and dynamic conditions to determine the corrosivity of the fluid . The procedures followed and

Solution blow spinning: parameters optimization and effects on the properties of nanofibers from poly(lactic) acid/dimethyl carbonate solutions

USDA-ARS?s Scientific Manuscript database

Solution blow spinning (SBS) is a process to produce non-woven fiber sheets with high porosity and an extremely large amount of surface area. In this study, a Box-Behnken experimental design (BBD) was used to optimize the processing parameters for the production of nanofibers from polymer solutions ...

75 FR 4288 - Oxirane, 2-Methyl-, Polymer with Oxirane, Dimethyl Ether; Tolerance Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-27

... a finite tolerance is not necessary to ensure that there is a reasonable certainty that no harm will... composition the atomic elements carbon, hydrogen, and oxygen. 3. The polymer does not contain as an integral part of its composition, except as impurities, any element other than those listed in 40 CFR 723.250(d...

Unravelling abiotic and biotic controls on the seasonal water balance using data-driven dimensionless diagnostics

NASA Astrophysics Data System (ADS)

Seibert, Simon Paul; Jackisch, Conrad; Ehret, Uwe; Pfister, Laurent; Zehe, Erwin

2017-06-01

The baffling diversity of runoff generation processes, alongside our sketchy understanding of how physiographic characteristics control fundamental hydrological functions of water collection, storage, and release, continue to pose major research challenges in catchment hydrology. Here, we propose innovative data-driven diagnostic signatures for overcoming the prevailing status quo in catchment inter-comparison. More specifically, we present dimensionless double mass curves (dDMC) which allow inference of information on runoff generation and the water balance at the seasonal and annual timescales. By separating the vegetation and winter periods, dDMC furthermore provide information on the role of biotic and abiotic controls in seasonal runoff formation. A key aspect we address in this paper is the derivation of dimensionless expressions of fluxes which ensure the comparability of the signatures in space and time. We achieve this by using the limiting factors of a hydrological process as a scaling reference. We show that different references result in different diagnostics. As such we define two kinds of dDMC which allow us to derive seasonal runoff coefficients and to characterize dimensionless streamflow release as a function of the potential renewal rate of the soil storage. We expect these signatures for storage controlled seasonal runoff formation to remain invariant, as long as the ratios of release over supply and supply over storage capacity develop similarly in different catchments. We test the proposed methods by applying them to an operational data set comprising 22 catchments (12-166 km2) from different environments in southern Germany and hydrometeorological data from 4 hydrological years. The diagnostics are used to compare the sites and to reveal the dominant controls on runoff formation. The key findings are that dDMC are meaningful signatures for catchment runoff formation at the seasonal to annual scale and that the type of scaling strongly influences the diagnostic potential of the dDMC. Adding discrimination between growing season and winter period was of fundamental importance and easy to implement by means of a temperature-index model. More specifically, temperature aggregates explain over 70 % of the variability of the seasonal summer runoff coefficients. The results also show that the soil topographic index, i.e. the product of topographic gradient and saturated hydraulic conductivity, is significantly correlated with winter runoff coefficients, whereas the topographic gradient and the hydraulic conductivity alone are not. We conclude that proxies for gradients and resistances should be interpreted as a pair. Lastly, the dDMC concept reveals memory effects between summer and winter runoff regimes that are not relevant in spring between the transition from winter to summer.

Use of aluminum phosphate as the dehydration catalyst in single step dimethyl ether process

DOEpatents

Peng, Xiang-Dong; Parris, Gene E.; Toseland, Bernard A.; Battavio, Paula J.

1998-01-01

The present invention pertains to a process for the coproduction of methanol and dimethyl ether (DME) directly from a synthesis gas in a single step (hereafter, the "single step DME process"). In this process, the synthesis gas comprising hydrogen and carbon oxides is contacted with a dual catalyst system comprising a physical mixture of a methanol synthesis catalyst and a methanol dehydration catalyst. The present invention is an improvement to this process for providing an active and stable catalyst system. The improvement comprises the use of an aluminum phosphate based catalyst as the methanol dehydration catalyst. Due to its moderate acidity, such a catalyst avoids the coke formation and catalyst interaction problems associated with the conventional dual catalyst systems taught for the single step DME process.

DMAC and NMP as Electrolyte Additives for Li-Ion Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall; Bugga, Ratnakumar; Lucht, Brett

2008-01-01

Dimethyl acetamide (DMAC) and N-methyl pyrrolidinone (NMP) have been found to be useful as high-temperature-resilience-enhancing additives to a baseline electrolyte used in rechargeable lithium-ion electrochemical cells. The baseline electrolyte, which was previously formulated to improve low-temperature performance, comprises LiPF6 dissolved at a concentration of 1.0 M in a mixture comprising equal volume proportions of ethylene carbonate, diethyl carbonate, and dimethyl carbonate. This and other electrolytes comprising lithium salts dissolved in mixtures of esters (including alkyl carbonates) have been studied in continuing research directed toward extending the lower limits of operating temperatures and, more recently, enhancing the high-temperature resilience of such cells. This research at earlier stages, and the underlying physical and chemical principles, were reported in numerous previous NASA Tech Briefs articles. Although these electrolytes provide excellent performance at low temperatures (typically as low as -40 C), when the affected Li-ion cells are subjected to high temperatures during storage and cycling, there occur irreversible losses of capacity accompanied by power fade and deterioration of low-temperature performance. The term "high-temperature resilience" signifies, loosely, the ability of a cell to resist such deterioration, retaining as much as possible of its initial charge/discharge capacity during operation or during storage in the fully charged condition at high temperature. For the purposes of the present development, a temperature is considered to be high if it equals or exceeds the upper limit (typically, 30 C) of the operating-temperature range for which the cells in question are generally designed.

Cognitive function and advanced kidney disease: longitudinal trends and impact on decision-making.

PubMed

Iyasere, Osasuyi; Okai, David; Brown, Edwina

2017-02-01

Background: Cognitive impairment commonly affects renal patients. But little is known about the influence of dialysis modality on cognitive trends or the influence of cognitive impairment on decision-making in renal patients. This study evaluated cognitive trends amongst chronic kidney disease (CKD), haemodialysis (HD) and peritoneal dialysis (PD) patients. The relationship between cognitive impairment and decision-making capacity (DMC) was also assessed. Methods: Patients were recruited from three outpatient clinics. Cognitive function was assessed 4-monthly for up to 2 years, using the Montreal Cognitive Assessment (MoCA) tool. Cognitive trends were assessed using mixed model analysis. DMC was assessed using the Macarthur Competency Assessment tool (MacCAT-T). MacCAT-T scores were compared between patients with cognitive impairment (MoCA <26) and those without. Results: In total, 102 (41 HD, 25 PD and 36 CKD) patients were recruited into the prospective study. After multivariate analysis, the total MoCA scores declined faster in dialysis compared with CKD patients [coefficient = -0.03, 95% confidence interval (95% CI) = -0.056 to - 0.004; P = 0.025]. The MoCA executive scores declined faster in the HD compared with PD patients (coefficient = -0.12, 95% CI = -0.233 to - 0.007; P = 0.037). DMC was assessed in 10 patients. Those with cognitive impairment had lower MacCAT-T compared with those without [median (interquartile range) 19 (17.9-19.6) versus 17.4 (16.3-18.4); P = 0.049]. Conclusions: Cognition declines faster in dialysis patients compared with CKD patients and in HD patients compared with PD patients. Cognitive impairment affects DMC in patients with advanced kidney disease.

Genetic parameters and prediction of genotypic values for root quality traits in cassava using REML/BLUP.

PubMed

Oliveira, E J; Santana, F A; Oliveira, L A; Santos, V S

2014-08-28

The aim of this study was to estimate the genetic parameters and predict the genotypic values of root quality traits in cassava (Manihot esculenta Crantz) using restricted maximum likelihood (REML) and best linear unbiased prediction (BLUP). A total of 471 cassava accessions were evaluated over two years of cultivation. The evaluated traits included amylose content (AML), root dry matter (DMC), cyanogenic compounds (CyC), and starch yield (StYi). Estimates of the individual broad-sense heritability of AML were low (hg(2) = 0.07 ± 0.02), medium for StYi and DMC, and high for CyC. The heritability of AML was substantially improved based on mean of accessions (hm(2) = 0.28), indicating that some strategies such as increasing the number of repetitions can be used to increase the selective efficiency. In general, the observed genotypic values were very close to the predicted average of the improved population, most likely due to the high accuracy (>0.90), especially for DMC, CyC, and StYi. Gains via selection of the 30 best genotypes for each trait were 4.8 and 3.2% for an increase and decrease for AML, respectively, an increase of 10.75 and 74.62% for DMC for StYi, respectively, and a decrease of 89.60% for CyC in relation to the overall mean of the genotypic values. Genotypic correlations between the quality traits of the cassava roots collected were generally favorable, although they were low in magnitude. The REML/BLUP method was adequate for estimating genetic parameters and predicting the genotypic values, making it useful for cassava breeding.

The combination of dimethoxycurcumin with DNA methylation inhibitor enhances gene re-expression of promoter-methylated genes and antagonizes their cytotoxic effect

PubMed Central

Hassan, Hazem E.; Keita, Jean-Arnaud; Narayan, Lawrence; Brady, Sean M.; Frederick, Richard; Carlson, Samuel; C. Glass, Karen; Natesan, Senthil; Buttolph, Thomm; Fandy, Tamer E.

2016-01-01

ABSTRACT Curcumin and its analogs exhibited antileukemic activity either as single agent or in combination therapy. Dimethoxycurcumin (DMC) is a more metabolically stable curcumin analog that was shown to induce the expression of promoter-methylated genes without reversing DNA methylation. Accordingly, co-treatment with DMC and DNA methyltransferase (DNMT) inhibitors could hypothetically enhance the re-expression of promoter-methylated tumor suppressor genes. In this study, we investigated the cytotoxic effects and epigenetic changes associated with the combination of DMC and the DNMT inhibitor decitabine (DAC) in primary leukemia samples and cell lines. The combination demonstrated antagonistic cytotoxic effects and was minimally cytotoxic to primary leukemia cells. The combination did not affect the metabolic stability of DMC. Although the combination enhanced the downregulation of nuclear DNMT proteins, the hypomethylating activity of the combination was not increased significantly compared to DAC alone. On the other hand, the combination significantly increased H3K27 acetylation (H3K27Ac) compared to the single agents near the promoter region of promoter-methylated genes. Furthermore, sequential chromatin immunoprecipitation (ChIP) and DNA pyrosequencing of the chromatin-enriched H3K27Ac did not show any significant decrease in DNA methylation compared to other regions. Consequently, the enhanced induction of promoter-methylated genes by the combination compared to DAC alone is mediated by a mechanism that involves increased histone acetylation and not through potentiation of the DNA hypomethylating activity of DAC. Collectively, our results provide the mechanistic basis for further characterization of this combination in leukemia animal models and early phase clinical trials. PMID:27588609

Mek1 Down Regulates Rad51 Activity during Yeast Meiosis by Phosphorylation of Hed1.

PubMed

Callender, Tracy L; Laureau, Raphaelle; Wan, Lihong; Chen, Xiangyu; Sandhu, Rima; Laljee, Saif; Zhou, Sai; Suhandynata, Ray T; Prugar, Evelyn; Gaines, William A; Kwon, YoungHo; Börner, G Valentin; Nicolas, Alain; Neiman, Aaron M; Hollingsworth, Nancy M

2016-08-01

During meiosis, programmed double strand breaks (DSBs) are repaired preferentially between homologs to generate crossovers that promote proper chromosome segregation at Meiosis I. In many organisms, there are two strand exchange proteins, Rad51 and the meiosis-specific Dmc1, required for interhomolog (IH) bias. This bias requires the presence, but not the strand exchange activity of Rad51, while Dmc1 is responsible for the bulk of meiotic recombination. How these activities are regulated is less well established. In dmc1Δ mutants, Rad51 is actively inhibited, thereby resulting in prophase arrest due to unrepaired DSBs triggering the meiotic recombination checkpoint. This inhibition is dependent upon the meiosis-specific kinase Mek1 and occurs through two different mechanisms that prevent complex formation with the Rad51 accessory factor Rad54: (i) phosphorylation of Rad54 by Mek1 and (ii) binding of Rad51 by the meiosis-specific protein Hed1. An open question has been why inhibition of Mek1 affects Hed1 repression of Rad51. This work shows that Hed1 is a direct substrate of Mek1. Phosphorylation of Hed1 at threonine 40 helps suppress Rad51 activity in dmc1Δ mutants by promoting Hed1 protein stability. Rad51-mediated recombination occurring in the absence of Hed1 phosphorylation results in a significant increase in non-exchange chromosomes despite wild-type levels of crossovers, confirming previous results indicating a defect in crossover assurance. We propose that Rad51 function in meiosis is regulated in part by the coordinated phosphorylation of Rad54 and Hed1 by Mek1.

The comprehensive electrophysiological study of curcuminoids on delayed-rectifier K+ currents in insulin-secreting cells.

PubMed

Kuo, Ping-Chung; Yang, Chia-Jung; Lee, Yu-Chi; Chen, Pei-Chun; Liu, Yen-Chin; Wu, Sheng-Nan

2018-01-15

Curcumin (CUR) has been demonstrated to induce insulin release from pancreatic β-cells; however, how curcuminoids (including demethoxycurcumin (DMC) and bisdemethoxycurcumin (BDMC)) exert any possible effects on membrane ion currents inherently in insulin-secreting cells remains largely unclear. The effects of CUR and other structurally similar curcuminoids on ion currents in rat insulin-secreting (INS-1) insulinoma cells were therefore investigated in this study. The effects of these compounds on ionic currents and membrane potential were studied by patch-clamp technique. CUR suppressed the amplitude of delayed-rectifier K + current (I K(DR) ) in a time-, state- and concentration-dependent manner in these cells and the inhibition was not reversed by diazoxide, nicorandil or chlorotoxin. The value of dissociation constant for CUR-induced suppression of I K(DR) in INS-1 cells was 1.26μM. Despite the inability of CUR to alter the activation rate of I K(DR) , it accelerated current inactivation elicited by membrane depolarization. Increasing CUR concentrations shifted the inactivation curve of I K(DR) to hyperpolarized potential and slowed the recovery of I K(DR) inactivation. CUR, DMC, and BDMC all exerted depressant actions on I K(DR) amplitude to a similar magnitude, although DMC and BDMC did not increase current inactivation clearly. CUR slightly suppressed the peak amplitude of voltage-gated Na + current. CUR, DMC and BDMC depolarized the resting potential and increased firing frequency of action potentials. The CUR-mediated decrease of I K(DR) and the increase of current inactivation also occurred in βTC-6 INS-1 cells. Taken these results together, these effects may be one of the possible mechanisms contributing their insulin-releasing effect. Copyright © 2017 Elsevier B.V. All rights reserved.

Organic solvents, electrolytes, and lithium ion cells with good low temperature performance

NASA Technical Reports Server (NTRS)

Huang, Chen-Kuo (Inventor); Smart, Marshall C. (Inventor); Surampudi, Subbarao (Inventor); Bugga, Ratnakumar V. (Inventor)

2002-01-01

Multi-component organic solvent systems, electrolytes and electrochemical cells characterized by good low temperature performance are provided. In one embodiment, an improved organic solvent system contains a ternary mixture of ethylene carbonate, dimethyl carbonate and diethyl carbonate. In other embodiments, quaternary systems include a fourth component, i.e, an aliphatic ester, an asymmetric alkyl carbonate or a compound of the formula LiOX, where X is R, COOR, or COR, where R is alkyl or fluoroalkyl. Electrolytes based on such organic solvent systems are also provided and contain therein a lithium salt of high ionic mobility, such as LiPF.sub.6. Reversible electrochemical cells, particularly lithium ion cells, are constructed with the improved electrolytes, and preferably include a carbonaceous anode, an insertion type cathode, and an electrolyte interspersed therebetween.

76 FR 7703 - 1,4-Benzenedicarboxylic Acid, Dimethyl Ester, Polymer With 1,4-Butanediol, Adipic Acid, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-11

... of pesticide use in residential settings. If EPA is able to determine that a finite tolerance is not... part of its composition the atomic elements carbon, hydrogen, and oxygen. 3. The polymer does not contain as an integral part of its composition, except as impurities, any element other than those listed...

Inhibition of microbiological sulfide oxidation by methanethiol and dimethyl polysulfides at natron-alkaline conditions.

PubMed

van den Bosch, Pim L F; de Graaff, Marco; Fortuny-Picornell, Marc; van Leerdam, Robin C; Janssen, Albert J H

2009-06-01

To avoid problems related to the discharge of sulfidic spent caustics, a biotechnological process is developed for the treatment of gases containing both hydrogen sulfide and methanethiol. The process operates at natron-alkaline conditions (>1 mol L(-1) of sodium- and potassium carbonates and a pH of 8.5-10) to enable the treatment of gases with a high partial CO(2) pressure. In the process, methanethiol reacts with biologically produced sulfur particles to form a complex mixture predominantly consisting of inorganic polysulfides, dimethyl disulfide (DMDS), and dimethyl trisulfide (DMTS). The effect of these organic sulfur compounds on the biological oxidation of sulfide to elemental sulfur was studied with natron-alkaliphilic bacteria belonging to the genus Thioalkalivibrio. Biological oxidation rates were reduced by 50% at 0.05 mM methanethiol, while for DMDS and DMTS, this was estimated to occur at 1.5 and 1.0 mM, respectively. The inhibiting effect of methanethiol on biological sulfide oxidation diminished due to its reaction with biologically produced sulfur particles. This reaction increases the feasibility of biotechnological treatment of gases containing both hydrogen sulfide and methanethiol at natron-alkaline conditions.

Many-body ab initio diffusion quantum Monte Carlo applied to the strongly correlated oxide NiO

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitra, Chandrima; Krogel, Jaron T.; Santana, Juan A.

2015-10-28

We present a many-body diffusion quantum Monte Carlo (DMC) study of the bulk and defect properties of NiO. We find excellent agreement with experimental values, within 0.3%, 0.6%, and 3.5% for the lattice constant, cohesive energy, and bulk modulus, respectively. The quasiparticle bandgap was also computed, and the DMC result of 4.72 (0.17) eV compares well with the experimental value of 4.3 eV. Furthermore, DMC calculations of excited states at the L, Z, and the gamma point of the Brillouin zone reveal a flat upper valence band for NiO, in good agreement with Angle Resolved Photoemission Spectroscopy results. To studymore » defect properties, we evaluated the formation energies of the neutral and charged vacancies of oxygen and nickel in NiO. A formation energy of 7.2 (0.15) eV was found for the oxygen vacancy under oxygen rich conditions. For the Ni vacancy, we obtained a formation energy of 3.2 (0.15) eV under Ni rich conditions. These results confirm that NiO occurs as a p-type material with the dominant intrinsic vacancy defect being Ni vacancy.« less

Protective effects of 2',4'-dihydroxy-6'-methoxy-3',5'-dimethylchalcone to PC12 cells against cytotoxicity induced by hydrogen peroxide.

PubMed

Su, Ming-Yuan; Huang, Hai-Ya; Li, Lin; Lu, Yan-Hua

2011-01-26

Oxidative stress has been considered as a major cause of cellular injuries in various clinical abnormalities. One of the possible ways to prevent reactive oxygen species (ROS)-mediated cellular injury is dietary or pharmaceutical therapies to augment the endogenous antioxidant defense capacity. The present study found that 2',4'-dihydroxy-6'-methoxy-3',5'-dimethylchalcone (DMC), a chalcone isolated from the buds of Cleistocalyx operculatus, possessed cytoprotective activity in PC12 cells treated with H(2)O(2). The results showed that DMC could effectively increase cell viability [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazoliumbromide (MTT) reduction], decrease the cell apoptotic percentage [annexin V/propidium iodide (AV/PI) assay], prevent the membrane from damage [lactate dehydrogenase (LDH) release], scavenge ROS formation, reduce caspase-3 activity, and attenuate the decrease of mitochondrial membrane potential (MMP) in PC12 cells treated with H(2)O(2). Meanwhile, DMC increased the catalytic activity of superoxide dismutase (SOD) and the cellular amount of glutathione (GSH), decreased the cellular amount of malondialdehyde (MDA), and decreased the production of lipid peroxidation in PC12 cells treated with H(2)O(2).

Diagrammatic Monte Carlo study of Fröhlich polaron dispersion in two and three dimensions

NASA Astrophysics Data System (ADS)

Hahn, Thomas; Klimin, Sergei; Tempere, Jacques; Devreese, Jozef T.; Franchini, Cesare

2018-04-01

We present results for the solution of the large polaron Fröhlich Hamiltonian in 3 dimensions (3D) and 2 dimensions (2D) obtained via the diagrammatic Monte Carlo (DMC) method. Our implementation is based on the approach by Mishchenko [A. S. Mishchenko et al., Phys. Rev. B 62, 6317 (2000), 10.1103/PhysRevB.62.6317]. Polaron ground state energies and effective polaron masses are successfully benchmarked with data obtained using Feynman's path integral formalism. By comparing 3D and 2D data, we verify the analytically exact scaling relations for energies and effective masses from 3 D →2 D , which provides a stringent test for the quality of DMC predictions. The accuracy of our results is further proven by providing values for the exactly known coefficients in weak- and strong-coupling expansions. Moreover, we compute polaron dispersion curves which are validated with analytically known lower and upper limits in the small-coupling regime and verify the first-order expansion results for larger couplings, thus disproving previous critiques on the apparent incompatibility of DMC with analytical results and furnishing useful reference for a wide range of coupling strengths.

When Does Decisional Impairment Become Decisional Incompetence? Ethical and Methodological Issues in Capacity Research in Schizophrenia

PubMed Central

Kim, Scott Y H

2006-01-01

Most decision-making capacity (DMC) research has focused on measuring the decision-making abilities of patients, rather than on how such persons may be categorized as competent or incompetent. However, research ethics policies and practices either assume that we can differentiate or attempt to guide the differentiation of the competent from the incompetent. Thus there is a need to build on the recent advances in capacity research by conceptualizing and studying DMC as a categorical concept. This review discusses why there is a need for such research and addresses challenges and obstacles, both practical and theoretical. After a discussion of the potential obstacles and suggesting ways to overcome them, it discusses why clinicians with expertise in capacity assessments may be the best source of a provisional “gold standard” for criterion validation of categorical capacity status. The review provides discussions of selected key methodological issues in conducting research that treats DMC as a categorical concept, such as the issue of the optimal number of expert judges needed to generate a criterion standard and the kinds of information presented to the experts in obtaining their judgments. Future research needs are outlined. PMID:16177276

IRIS Earthquake Browser with Integration to the GEON IDV for 3-D Visualization of Hypocenters.

NASA Astrophysics Data System (ADS)

Weertman, B. R.

2007-12-01

We present a new generation of web based earthquake query tool - the IRIS Earthquake Browser (IEB). The IEB combines the DMC's large set of earthquake catalogs (provided by USGS/NEIC, ISC and the ANF) with the popular Google Maps web interface. With the IEB you can quickly and easily find earthquakes in any region of the globe. Using Google's detailed satellite images, earthquakes can be easily co-located with natural geographic features such as volcanoes as well as man made features such as commercial mines. A set of controls allow earthquakes to be filtered by time, magnitude, and depth range as well as catalog name, contributor name and magnitude type. Displayed events can be easily exported in NetCDF format into the GEON Integrated Data Viewer (IDV) where hypocenters may be visualized in three dimensions. Looking "under the hood", the IEB is based on AJAX technology and utilizes REST style web services hosted at the IRIS DMC. The IEB is part of a broader effort at the DMC aimed at making our data holdings available via web services. The IEB is useful both educationally and as a research tool.

Structure and Electrochemistry of Copper Fluoride Nanocomposites Utilizing Mixed Conducting Matrices

DTIC Science & Technology

2007-01-01

similar to the conversion reaction of the metal fluoride. Attractive materials such as V2O5 , MoS2, and MoO3-δ can be utilized. Examples of metal...fluorides enabled by these MCM matrices are nanocomposites of FeF3 ( V2O5 ),2 BiF3 (MoS2),15 and as discussed herein, CuF2 (MoO3). In all cases, the...filled dry box using Whatman GF/D glass fiber separators saturated with 1M LiPF6 in 1:1 vol/vol ethylene carbonate:dimethyl carbonate elec- trolyte

Extended Le Chatelier's formula for carbon dioxide dilution effect on flammability limits.

PubMed

Kondo, Shigeo; Takizawa, Kenji; Takahashi, Akifumi; Tokuhashi, Kazuaki

2006-11-02

Carbon dioxide dilution effect on the flammability limits was measured for various flammable gases. The obtained values were analyzed using the extended Le Chatelier's formula developed in a previous study. As a result, it has been found that the flammability limits of methane, propane, propylene, methyl formate, and 1,1-difluoroethane are adequately explained by the extended Le Chatelier's formula using a common set of parameter values. Ethylene, dimethyl ether, and ammonia behave differently from these compounds. The present result is very consistent with what was obtained in the case of nitrogen dilution.

Structure of spontaneously formed solid-electrolyte interphase on lithiated graphite determined using small-angle neutron scattering

DOE PAGES

Sacci, Robert L.; Banuelos, Jose Leobardo; Veith, Gabriel M.; ...

2015-03-25

We report the first small-angle neutron scattering of a chemically formed solid-electrolyte interphase from LixC6 reacting with ethylene carbonate/dimethyl carbon solvent. This provides a different and perhaps simpler view of SEI formation than the usual electrochemically-driven reaction. We show that an organic layer coats the graphite particles filling in micro-pores and is polymeric in nature being 1-3 nm thick. We used inelastic neutron scattering to probe the chemistry, and we found that the SEI showed similar inelastic scattering to polyethylene oxide.

X-ray Raman spectroscopy of lithium-ion battery electrolyte solutions in a flow cell.

PubMed

Ketenoglu, Didem; Spiekermann, Georg; Harder, Manuel; Oz, Erdinc; Koz, Cevriye; Yagci, Mehmet C; Yilmaz, Eda; Yin, Zhong; Sahle, Christoph J; Detlefs, Blanka; Yavaş, Hasan

2018-03-01

The effects of varying LiPF 6 salt concentration and the presence of lithium bis(oxalate)borate additive on the electronic structure of commonly used lithium-ion battery electrolyte solvents (ethylene carbonate-dimethyl carbonate and propylene carbonate) have been investigated. X-ray Raman scattering spectroscopy (a non-resonant inelastic X-ray scattering method) was utilized together with a closed-circle flow cell. Carbon and oxygen K-edges provide characteristic information on the electronic structure of the electrolyte solutions, which are sensitive to local chemistry. Higher Li + ion concentration in the solvent manifests itself as a blue-shift of both the π* feature in the carbon edge and the carbonyl π* feature in the oxygen edge. While these oxygen K-edge results agree with previous soft X-ray absorption studies on LiBF 4 salt concentration in propylene carbonate, carbon K-edge spectra reveal a shift in energy, which can be explained with differing ionic conductivities of the electrolyte solutions.

A High-Performance Nanocomposite Material Based on Functionalized Carbon Nanotube and Polymer for Gas Sensing Applications

NASA Astrophysics Data System (ADS)

Wang, L. C.; Tang, K. T.; Kuo, C. T.; Yang, S. R.; Sung, Yuh; Hsu, H. L.; Jehng, J. M.

2009-05-01

The aim of this study is to develop a novel chemical gas sensing nanocomposite material. The traditional use for carbon nanotube in gas sensing polymer is to increase the composite's conductivity. However, we added functionalized carbon nanotube to fill the free volume of the sensing polymer films and enhance the gas absorption/desorption response time of these nanocomposites. These sensing materials were prepared by mixing functionalized multiwalled carbon nanotubes (MWNTs) and Poly (n, n dimethylamino propylsilsequioxane) SXNR polymer. These new materials were coated on the Surface Acoustic Wave (SAW) device, which is expected to increase its sensitivity in analyzing specific classes of vapors. The proposed materials showed an enhanced sensitivity upon exposure to ethanol and dimethyl methylphosphonate (Dmmp) vapors. Additionally, the performances of our nanocomposite film are much higher than those polymers without functionalized carbon nanotubes.

40 CFR 414.91 - Toxic pollutant effluent limitations and standards for direct discharge point sources that use...

Code of Federal Regulations, 2012 CFR

2012-07-01

...(k)fluoranthene 59 22 Benzo(a)pyrene 61 23 Bis(2-ethylhexyl) phthalate 279 103 Carbon Tetrachloride... Di-n-butyl phthalate 57 27 1,2-Dichlorobenzene 163 77 1,3-Dichlorobenzene 44 31 1,4-Dichlorobenzene... phthalate 203 81 2,4-Dimethylphenol 36 18 Dimethyl phthalate 47 19 4,6-Dinitro-o-cresol 277 78 2,4...

40 CFR 414.91 - Toxic pollutant effluent limitations and standards for direct discharge point sources that use...

Code of Federal Regulations, 2014 CFR

2014-07-01

...(k)fluoranthene 59 22 Benzo(a)pyrene 61 23 Bis(2-ethylhexyl) phthalate 279 103 Carbon Tetrachloride... Di-n-butyl phthalate 57 27 1,2-Dichlorobenzene 163 77 1,3-Dichlorobenzene 44 31 1,4-Dichlorobenzene... phthalate 203 81 2,4-Dimethylphenol 36 18 Dimethyl phthalate 47 19 4,6-Dinitro-o-cresol 277 78 2,4...

40 CFR 414.101 - Toxic pollutant effluent limitations and standards for direct discharge point sources that do not...

Code of Federal Regulations, 2012 CFR

2012-07-01

...(k)fluoranthene 47 19 Benzo(a)pyrene 48 20 Bis(2-ethylhexyl) phthalate 258 95 Carbon Tetrachloride... phthalate 43 20 1,2-Dichlorobenzene 794 196 1,3-Dichlorobenzene 380 142 1,4-Dichlorobenzene 380 142 1,1...-Dichloropropane 794 196 1,3-Dichloropropylene 794 196 Diethyl phthalate 113 46 2,4-Dimethylphenol 47 19 Dimethyl...

40 CFR 414.101 - Toxic pollutant effluent limitations and standards for direct discharge point sources that do not...

Code of Federal Regulations, 2014 CFR

2014-07-01

...(k)fluoranthene 47 19 Benzo(a)pyrene 48 20 Bis(2-ethylhexyl) phthalate 258 95 Carbon Tetrachloride... phthalate 43 20 1,2-Dichlorobenzene 794 196 1,3-Dichlorobenzene 380 142 1,4-Dichlorobenzene 380 142 1,1...-Dichloropropane 794 196 1,3-Dichloropropylene 794 196 Diethyl phthalate 113 46 2,4-Dimethylphenol 47 19 Dimethyl...

Cu@C nanoporous composites containing little copper oxides derived from dimethyl imidazole modified MOF199 as electrocatalysts for hydrogen evolution reaction

NASA Astrophysics Data System (ADS)

Wei, Xuedong; Li, Na; Zhang, Xianming

2017-12-01

It remains a huge challenge to develop non precious electrocatalysts with high activity to substitute commercial Pt catalysts for hydrogen evolution reactions (HER). Here, the C-Cu-DI and C-Cu materials with the copper based nanoporous carbon structures were synthesized by carbonizing MOF199 and DI-MOF199. The composite structure and HER electrocatalytic properties of the C-Cu-DI and C-Cu materials are studied. The results show that C-Cu-DI and C-Cu samples exhibit good catalytic activity. And C-Cu-DI sample through the addition of Dimethyl imidazole(DI) in the DI-MOF199 precursor has higher electrocatalytic activity than the C-Cu sample. The superior catalytic activity is attributed to the special composite structure of nanoscale deposition particles on the framework with plenty of nano pores and nano copper and few copper oxidation particles distributed or wrapped into the amorphous porous carbon phase. The nano copper and few copper oxidation particles in the C-Cu and C-Cu-DI catalysts maybe provide the more effective catalytic activity sites. The C-Cu-DI composite with large size spherical hollow deposition particles has higher conductivity, better BET surface area and reasonable micro-meso-macro porous distribution, so the overpotentials at the current density of 1 mA cm-2 and 10 mA cm-2 are respectively 270 mV and 390 mV vs. RHE. Although the HER activity has a big gap with commercial platinum catalyst, this study can provide an important experimental exploration for the design of copper based non noble metal/nano porous carbon composite HER electrocatalyst.

Frequentist and Bayesian Orbital Parameter Estimaton from Radial Velocity Data Using RVLIN, BOOTTRAN, and RUN DMC

NASA Astrophysics Data System (ADS)

Nelson, Benjamin Earl; Wright, Jason Thomas; Wang, Sharon

2015-08-01

For this hack session, we will present three tools used in analyses of radial velocity exoplanet systems. RVLIN is a set of IDL routines used to quickly fit an arbitrary number of Keplerian curves to radial velocity data to find adequate parameter point estimates. BOOTTRAN is an IDL-based extension of RVLIN to provide orbital parameter uncertainties using bootstrap based on a Keplerian model. RUN DMC is a highly parallelized Markov chain Monte Carlo algorithm that employs an n-body model, primarily used for dynamically complex or poorly constrained exoplanet systems. We will compare the performance of these tools and their applications to various exoplanet systems.

Permeable reactive barrier of surface hydrophobic granular activated carbon coupled with elemental iron for the removal of 2,4-dichlorophenol in water.

PubMed

Yang, Ji; Cao, Limei; Guo, Rui; Jia, Jinping

2010-12-15

Granular activated carbon was modified with dimethyl dichlorosilane to improve its surface hydrophobicity, and therefore to improve the performance of permeable reactive barrier constructed with the modified granular activated carbon and elemental iron. X-ray photoelectron spectroscopy shows that the surface silicon concentration of the modified granular activated carbon is higher than that of the original one, leading to the increased surface hydrophobicity. Although the specific surface area decreased from 895 to 835 m(2)g(-1), the modified granular activated carbon could adsorb 20% more 2,4-dichlorophenol than the original one did in water. It is also proven that the permeable reactive barrier with the modified granular activated carbon is more efficient at 2,4-dichlorophenol dechlorination, in which process 2,4-dichlorophenol is transformed to 2-chlorophenol or 4-chlorophenol then to phenol, or to phenol directly. Copyright © 2010 Elsevier B.V. All rights reserved.

Synthesis and structure identification of 2-amino-4, 6- dimethyl pyrimidine with gallic acid and pimelic acid

NASA Astrophysics Data System (ADS)

Mekala, R.; Jagdish, P.; Mathammal, R.

2018-07-01

Reaction of 2-amino-4, 6- dimethyl pyrimidine with carboxylic acid such as gallic acid and pimelic acid, yielded a salt and co-crystal, respectively. The new crystal forms were obtained from slow evaporation technique. The crystal structure and hydrogen bond interaction of the two crystals were determined by single X-ray diffraction analysis. Inter molecular interactions of the compounds were investigated using the 3D Hirshfeld surfaces and the associated 2D fingerprint plots. The functional groups were identified by the FTIR, FT-Raman spectral studies. The presence of carbon and hydrogen in the two samples were identified by the 1H and 13C NMR analysis. The excited energy was observed using UV-Visible spectral analysis. The fluorescence spectra revealed the emission state of the two samples. The thermal behaviour and stability of the two compounds were evaluated by the TGA-DSC analysis.

Many-body ab initio diffusion quantum Monte Carlo applied to the strongly correlated oxide NiO

DOE PAGES

Mitra, Chandrima; Krogel, Jaron T.; Santana, Juan A.; ...

2015-10-28

We present a many-body diffusion quantum Monte Carlo (DMC) study of the bulk and defect properties of NiO. We find excellent agreement with experimental values, within 0.3%, 0.6%, and 3.5% for the lattice constant, cohesive energy, and bulk modulus, respectively. The quasiparticle bandgap was also computed, and the DMC result of 4.72 (0.17) eV compares well with the experimental value of 4.3 eV. Furthermore, DMC calculations of excited states at the L, Z, and the gamma point of the Brillouin zone reveal a flat upper valence band for NiO, in good agreement with Angle Resolved Photoemission Spectroscopy results. To studymore » defect properties, we evaluated the formation energies of the neutral and charged vacancies of oxygen and nickel in NiO. A formation energy of 7.2 (0.15) eV was found for the oxygen vacancy under oxygen rich conditions. For the Ni vacancy, we obtained a formation energy of 3.2 (0.15) eV under Ni rich conditions. Lastly, these results confirm that NiO occurs as a p-type material with the dominant intrinsic vacancy defect being Ni vacancy. (C) 2015 AIP Publishing LLC.« less

Detector Simulation and WIMP Search Analysis for the Cryogenic Dark Matter Search Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCarthy, Kevin

2013-06-01

Astrophysical and cosmological measurements on the scales of galaxies, galaxy clusters, and the universe indicate that 85% of the matter in the universe is composed of dark matter, made up of non-baryonic particles that interact with cross-sections on the weak scale or lower. Hypothetical Weakly Interacting Massive Particles, or WIMPs, represent a potential solution to the dark matter problem, and naturally arise in certain Standard Model extensions. The Cryogenic Dark Matter Search (CDMS) collaboration aims to detect the scattering of WIMP particles from nuclei in terrestrial detectors. Germanium and silicon particle detectors are deployed in the Soudan Underground Laboratory inmore » Minnesota. These detectors are instrumented with phonon and ionization sensors, which allows for discrimination against electromagnetic backgrounds, which strike the detector at rates orders of magnitude higher than the expected WIMP signal. This dissertation presents the development of numerical models of the physics of the CDMS detectors, implemented in a computational package collectively known as the CDMS Detector Monte Carlo (DMC). After substantial validation of the models against data, the DMC is used to investigate potential backgrounds to the next iteration of the CDMS experiment, known as SuperCDMS. Finally, an investigation of using the DMC in a reverse Monte Carlo analysis of WIMP search data is presented.« less

ExoMol line lists XXV: a hot line list for silicon sulphide, SiS

NASA Astrophysics Data System (ADS)

Upadhyay, Apoorva; Conway, Eamon K.; Tennyson, Jonathan; Yurchenko, Sergei N.

2018-06-01

SiS has long been observed in the circumstellar medium of the carbon-rich star IRC+10216 CW Leo. Comprehensive and accurate rotation-vibrational line lists and partition functions are computed for 12 isotopologues of silicon sulphide (28Si32S, 28Si34S, 29Si32S, 28Si33S, 30Si32S, 29Si34S, 30Si34S, 28Si36S, 29Si33S, 29Si36S, 30Si33S, and 30Si36S) in its ground (X 1Σ+) electronic state. The calculations employ an existing spectroscopically accurate potential energy curve (PEC) derived from experimental measurements and a newly computed ab initio dipole moment curve (DMC). The 28Si32S line list includes 10 104 states and 91 715 transitions. These line lists are available from the ExoMol website (www.exomol.com) and the CDS data base.

Studying the Dependency of Interfacial Formation with Carbon Nanotube

DTIC Science & Technology

2014-08-27

PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND...duration of this project toward understanding the interfacial formation and dependency on SWNT and its relationship to the nanotube length. SECTION II...obtained from Kuraray America Inc. Dimethyl sulfoxide (DMSO) was purchased from Sigma -Aldrich Corporation (CAS# 67-68-5, lot# 472301). Methanol was

Biodegradation of the Organophosphate Trichlorfon and Its Major Degradation Products by a Novel Aspergillus sydowii PA F-2.

PubMed

Tian, Jiang; Dong, Qiaofeng; Yu, Chenlei; Zhao, Ruixue; Wang, Jing; Chen, Lanzhou

2016-06-01

Trichlorfon (TCF) is an important organophosphate pesticide in agriculture. However, limited information is known about the biodegradation behaviors and kinetics of this pesticide. In this study, a newly isolated fungus (PA F-2) from pesticide-polluted soils was identified as Aspergillus sydowii on the basis of the sequencing of internal transcribed spacer rDNA. This fungus degraded TCF as sole carbon, sole phosphorus, and sole carbon-phosphorus sources in a mineral salt medium (MSM). Optimal TCF degradation conditions were determined through response surface methodology, and results also revealed that 75.31% of 100 mg/L TCF was metabolized within 7 days. The degradation of TCF was accelerated, and the mycelial dry weight of PA F-2 was remarkably increased in MSM supplemented with exogenous sucrose and yeast extract. Five TCF metabolic products were identified through gas chromatography-mass spectrometry. TCF could be initially hydrolyzed to dichlorvos and then be degraded through the cleavage of the P-C bond to produce dimethyl hydrogen phosphate and chloral hydrate. These two compounds were subsequently deoxidized to produce dimethyl phosphite and trichloroethanal. These results demonstrate the biodegradation pathways of TCF and promote the potential use of PA F-2 to bioremediate TCF-contaminated environments.

Ternary PtRuPd/C catalyst for high-performance, low-temperature direct dimethyl ether fuel cells

DOE PAGES

Dumont, Joseph Henry; Martinez, Ulises; Chung, Hoon T.; ...

2016-08-19

Here, dimethyl ether (DME) is a promising alternative fuel option for direct-feed low-temperature fuel cells. Until recently, DME had not received the same attention as alcohol fuels, such as methanol or ethanol, despite its notable advantages. These advantages include a high theoretical open-cell voltage (1.18 V at 25 °C) that is similar to that of methanol (1.21 V), much lower toxicity than methanol, and no need for the carbon–carbon bond scission that is needed in ethanol oxidation. DME is biodegradable, has a higher energy content than methanol (8.2 vs. 6.1 kWh kg –1), and, like methanol, can be synthesized frommore » recycled carbon dioxide. Although the performance of direct DME fuel cells (DDMEFCs) has progressed over the past few years, DDMEFCs have not been viewed as fully viable. In this work, we report much improved performance from the ternary Pt 55Ru 35Pd 10/C anode catalyst, allowing DDMEFCs to compete directly with direct methanol fuel cells (DMFCs). We also report results involving binary Pt alloys as reference catalysts and an in situ infrared electrochemical study to better understand the mechanism of DME electro-oxidation on ternary PtRuPd/C catalysts.« less

Synthesis of Thymoquinone derivatives and its activity analysis: In-silico approach

NASA Astrophysics Data System (ADS)

Ulfa, Siti Mariyah; Sholikhah, Shoimatus; Utomo, Edi Priyo

2017-03-01

Thymoquinone derivatives which synthesized in this research is bromoalkylquinones with alkyl chain consist of seven carbons (C7) and ten carbons (C10). The synthesis was carried out by oxidation of 2,3-dimethylhydroquinone followed by alkylation using reflux for 1.5 hours. The alkylation products were successfully characterized as 5-(7-bromoheptyl)-2,3-dimethyl-1,4-benzoquinone (C7) and 5-(10-bromodecyl)-2,3-dimethyl-1,4-benzoquinone (C10) in 31.93 and 16.89%, respectively. These compounds were fully characterized using FT-IR, 1H-NMR and 13C-NMR. Thus, the activity of C7 and C10 was analyzed by in silico approach with molecular docking using macromolecule model extracted from Protein Data Bank (PDB). Macromolecules used in this research is mitochondrial translocator protein (TSPO) as an antioxidant receptor, glycogen phosphorylase (GPA) as antidiabetic receptor and phosphatase tensin homolog (PTEN) as an anticancer agent. The result showed that C7 and C10 has a very good activity as antioxidant and antidiabetic agents with IC50 2.03 and 1.02 ppm (TSPO) and 16.98 and 14.88 ppm (GPA) compared with Thymoquinone. While the activity of C7 and C10 against PTEN gave the IC50 23.13 and 18.31 ppm showed a good candidate for an anticancer agent.

Effect of combinations of additives on the performance of lithium ion batteries

NASA Astrophysics Data System (ADS)

Santee, Stuart; Xiao, Ang; Yang, Li; Gnanaraj, Joe; Lucht, Brett L.

Commercial lithium-ion batteries have excellent performance at room temperature for a few years. However, the calendar life and thermal stability (>50 °C) need to be improved for many applications, including electric vehicles. We have conducted an investigation of the effect of thermal stabilizing additives, including dimethyl acetamide, vinylene carbonate, and lithium bis(oxalato) borate, on the performance of lithium ion batteries stored at 70 °C for one month. The reactions of the lithium hexafluorophosphate/carbonate electrolyte, with and without electrolyte additives, with the surface of the electrodes after initial formation cycling have been analyzed via a combination of IR-ATR and XPS.

/sup 13/C NMR spectra of cyclic nitrones. 1. 2-substituted 4-methyl- and 4-phenyl-1-hydroxy-5,5-dimethyl-3-imidazoline 3-oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grigor'ev, I.A.; Martin, V.V.; Shchukin, G.I.

1985-08-01

The introduction of an N-oxide oxygen atom into azomethines leads to an upfield shift of the signals for the carbon atom of the C=N group in the /sup 13/C NMR spectra by 30-33 ppm. This is consistent with the increase in the electron density on this atom. The signal of the nitrone carbon atom is observed in the region of 140-147 ppm, depending on the nature of the substituent at the C/sub (2)/ atom of the 3-imidazoline 3-oxide ring.

A New Method for Non-destructive Measurement of Biomass, Growth Rates, Vertical Biomass Distribution and Dry Matter Content Based on Digital Image Analysis

PubMed Central

Tackenberg, Oliver

2007-01-01

Background and Aims Biomass is an important trait in functional ecology and growth analysis. The typical methods for measuring biomass are destructive. Thus, they do not allow the development of individual plants to be followed and they require many individuals to be cultivated for repeated measurements. Non-destructive methods do not have these limitations. Here, a non-destructive method based on digital image analysis is presented, addressing not only above-ground fresh biomass (FBM) and oven-dried biomass (DBM), but also vertical biomass distribution as well as dry matter content (DMC) and growth rates. Methods Scaled digital images of the plants silhouettes were taken for 582 individuals of 27 grass species (Poaceae). Above-ground biomass and DMC were measured using destructive methods. With image analysis software Zeiss KS 300, the projected area and the proportion of greenish pixels were calculated, and generalized linear models (GLMs) were developed with destructively measured parameters as dependent variables and parameters derived from image analysis as independent variables. A bootstrap analysis was performed to assess the number of individuals required for re-calibration of the models. Key Results The results of the developed models showed no systematic errors compared with traditionally measured values and explained most of their variance (R2 ≥ 0·85 for all models). The presented models can be directly applied to herbaceous grasses without further calibration. Applying the models to other growth forms might require a re-calibration which can be based on only 10–20 individuals for FBM or DMC and on 40–50 individuals for DBM. Conclusions The methods presented are time and cost effective compared with traditional methods, especially if development or growth rates are to be measured repeatedly. Hence, they offer an alternative way of determining biomass, especially as they are non-destructive and address not only FBM and DBM, but also vertical biomass distribution and DMC. PMID:17353204

Fixed node diffusion Monte Carlo using a genetic algorithm: a study of the CO-(4)He(N) complex, N = 1…10.

PubMed

Ramilowski, Jordan A; Farrelly, David

2012-06-14

The diffusion Monte Carlo (DMC) method is a widely used algorithm for computing both ground and excited states of many-particle systems; for states without nodes the algorithm is numerically exact. In the presence of nodes approximations must be introduced, for example, the fixed-node approximation. Recently we have developed a genetic algorithm (GA) based approach which allows the computation of nodal surfaces on-the-fly [Ramilowski and Farrelly, Phys. Chem. Chem. Phys., 2010, 12, 12450]. Here GA-DMC is applied to the computation of rovibrational states of CO-(4)He(N) complexes with N≤ 10. These complexes have been the subject of recent high resolution microwave and millimeter-wave studies which traced the onset of microscopic superfluidity in a doped (4)He droplet, one atom at a time, up to N = 10 [Surin et al., Phys. Rev. Lett., 2008, 101, 233401; Raston et al., Phys. Chem. Chem. Phys., 2010, 12, 8260]. The frequencies of the a-type (microwave) series, which correlate with end-over-end rotation in the CO-(4)He dimer, decrease from N = 1 to 3 and then smoothly increase. This signifies the transition from a molecular complex to a quantum solvated system. The frequencies of the b-type (millimeter-wave) series, which evolves from free rotation of the rigid CO molecule, initially increase from N = 0 to N∼ 6 before starting to decrease with increasing N. An interesting feature of the b-type series, originally observed in the high resolution infra-red (IR) experiments of Tang and McKellar [J. Chem. Phys., 2003, 119, 754] is that, for N = 7, two lines are observed. The GA-DMC algorithm is found to be in good agreement with experimental results and possibly detects the small (∼0.7 cm(-1)) splitting in the b-series line at N = 7. Advantages and disadvantages of GA-DMC are discussed.

Gel polymer electrolyte for lithium-ion batteries comprising cyclic carbonate moieties

NASA Astrophysics Data System (ADS)

Tillmann, S. D.; Isken, P.; Lex-Balducci, A.

2014-12-01

A polymer system based on oligo (ethylene glycol) methyl ether methacrylate (OEGMA) and cyclic carbonate methacrylate (CCMA) was chosen as matrix to realize high-performance gel polymer electrolytes due to the fact that both monomers are able to interact with the liquid electrolyte, thus, retaining it inside the matrix. Additionally, OEGMA enables high flexibility, while CCMA provides mechanical stability. The polymer displays a high thermal stability up to 200 °C and a glass transition temperature below room temperature (5 °C) allowing an easy handling of the obtained films. By immobilizing the liquid electrolyte 1 M LiPF6 in EC:DMC 1:1 w:w in the polymer host a gel polymer electrolyte with a high conductivity of 2.3 mS cm-1 at 25 °C and a stable cycling behavior with high capacities and efficiencies in Li(Ni1/3Co1/3Mn1/3)O2 (NCM)/graphite full cells is obtained. The investigated gel polymer electrolyte is identified as promising electrolyte for lithium-ion batteries, because it combines good electrochemical properties comparable to that of liquid electrolytes with the safety advantage that no leakage of the flammable electrolyte solvents can occur.

The IRIS Data Management Center: An international "network of networks", providing open, automated access to geographically distributed sensors of geophysical and environmental data.

NASA Astrophysics Data System (ADS)

Benson, R. B.; Ahern, T. K.; Trabant, C.

2006-12-01

The IRIS Data Management System has long supported international collaboration for seismology by both deploying a global network of seismometers and creating and maintaining an open and accessible archive in Seattle, WA, known as the Data Management Center (DMC). With sensors distributed on a global scale spanning more than 30 years of digital data, the DMC provides a rich repository of observations across broad time and space domains. Primary seismological data types include strong motion and broadband seismometers, conventional and superconducting gravimeters, tilt and creep meters, GPS measurements, along with other similar sensors that record accurate and calibrated ground motion. What may not be as well understood is the volume of environmental data that accompanies typical seismological data these days. This poster will review the types of time-series data that are currently being collected, how they are collected, and made freely available for download at the IRIS DMC. Environmental sensor data that is often co-located with geophysical data sensors include temperature, barometric pressure, wind direction and speed, humidity, insolation, rain gauge, and sometimes hydrological data like water current, level, temperature and depth. As the primary archival institution of the International Federation of Digital Seismograph Networks (FDSN), the IRIS DMC collects approximately 13,600 channels of real-time data from 69 different networks, from close to 1600 individual stations, currently averaging 10Tb per year in total. A major contribution to the IRIS archive currently is the EarthScope project data, a ten-year science undertaking that is collecting data from a high-resolution, multi-variate sensor network. Data types include magnetotelluric, high-sample rate seismics from a borehole drilled into the San Andreas fault (SAFOD) and various types of strain data from the Plate Boundary Observatory (PBO). In addition to the DMC, data centers located in other countries are networked seamlessly, and are providing access for researchers to these data from national networks around the world utilizing the IRIS developed Data Handling Interface (DHI) system. This poster will highlight some of the DHI enabled clients that allow geophysical information to be directly transferred to the clients. This ability allows one to construct a virtual network of data centers providing the illusion of a single virtual observatory. Furthermore, some of the features that will be shown include direct connections to MATLAB and the ability to access globally distributed sensor data in real time. We encourage discussion and participation from network operators who would like to leverage existing technology, as well as enabling collaboration.

Ion chromatography electrospray ionization mass spectrometry method development and investigation of lithium hexafluorophosphate-based organic electrolytes and their thermal decomposition products.

PubMed

Kraft, Vadim; Grützke, Martin; Weber, Waldemar; Winter, Martin; Nowak, Sascha

2014-08-08

A method based on the coupling of ion chromatography (IC) and electrospray ionization mass spectrometry (ESI-MS) for the separation and determination of thermal decomposition products of LiPF6-based organic electrolytes is presented. The utilized electrolytes, LP30 and LP50, are commercially available and consist of 1mol/l LiPF6 dissolved in ethylene carbonate/dimethyl carbonate and ethylene carbonate/ethyl methyl carbonate, respectively. For the separation method development three ion chromatographic columns with different capacity and stationary phase were used and compared. Besides the known hydrolysis products of lithium hexafluorophosphate, several new organophosphates were separated and identified with the developed IC-ESI-MS method during aging investigations of the electrolytes. The chemical structures were elucidated with IC-ESI-MS/MS. Copyright © 2014 Elsevier B.V. All rights reserved.

Nanosized amorphous calcium carbonate stabilized by poly(ethylene oxide)-b-poly(acrylic acid) block copolymers.

PubMed

Guillemet, Baptiste; Faatz, Michael; Gröhn, Franziska; Wegner, Gerhard; Gnanou, Yves

2006-02-14

Particles of amorphous calcium carbonate (ACC), formed in situ from calcium chloride by the slow release of carbon dioxide by alkaline hydrolysis of dimethyl carbonate in water, are stabilized against coalescence in the presence of very small amounts of double hydrophilic block copolymers (DHBCs) composed of poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) blocks. Under optimized conditions, spherical particles of ACC with diameters less than 100 nm and narrow size distribution are obtained at a concentration of only 3 ppm of PEO-b-PAA as additive. Equivalent triblock or star DHBCs are compared to diblock copolymers. The results are interpreted assuming an interaction of the PAA blocks with the surface of the liquid droplets of the concentrated CaCO3 phase, formed by phase separation from the initially homogeneous reaction mixture. The adsorption layer of the block copolymer protects the liquid precursor of ACC from coalescence and/or coagulation.

Synthesis and electrochemical properties of niobium pentoxide deposited on layered carbide-derived carbon

NASA Astrophysics Data System (ADS)

Zhang, Chuanfang (John); Maloney, Ryan; Lukatskaya, Maria R.; Beidaghi, Majid; Dyatkin, Boris; Perre, Emilie; Long, Donghui; Qiao, Wenming; Dunn, Bruce; Gogotsi, Yury

2015-01-01

Herein we report on the hydrothermal synthesis of niobium pentoxide on carbide-derived carbon (Nb2O5/CDC) with a layered structure. The presence of phenylphosphonic acid guides the deposition during preparation, leading to the formation of amorphous Nb2O5 particles which are 4-10 nm in diameter and homogeneously distributed on the CDC framework. Electrochemical testing of the Nb2O5/CDC electrode indicated that the highest capacitance and Coulombic efficiency occurred using an electrolyte comprised of 1 M lithium perchlorate in ethylene carbonate/dimethyl carbonate. Subsequent heat treatment of Nb2O5/CDC in CO2 environment led to crystallization of the Nb2O5, allowing reversible Li+ intercalation/de-intercalation. For sweep rates corresponding to charging and discharging in under 3 min, a volumetric charge of 180 C cm-3 and Coulombic efficiency of 99.2% were attained.

Comparison of antioxidant, anticholinesterase, and antidiabetic activities of three curcuminoids isolated from Curcuma longa L.

PubMed

Kalaycıoğlu, Zeynep; Gazioğlu, Işıl; Erim, F Bedia

2017-12-01

Antioxidant, anticholinesterase and antidiabetic activities of three curcuminoids isolated from the Curcuma longa were simultaneously tested and compared in this study. The highest antioxidant power was detected for curcumin with the applied methods. The drug potentials of curcuminoids for Alzheimer's disease were controlled. Bisdemethoxycurcumin (BDMC) showed substantial inhibitory activity. The activity of demethoxycurcumin (DMC) followed BDMC, whereas curcumin showed very little acetylcholinesterase inhibition activity. Antidiabetic activity of curcuminoids was evaluated by their α-glucosidase inhibitory activities. All curcuminoids show activities with decreasing order as BDMC > curcumin > DMC. The significant activities of BDMC compared to its isomers and examination of chemical structures of isomers might be a starting point in designing new drugs for Alzheimer's and Diabetes Mellitus.

Electrochemical and theoretical characterization of the electro-oxidation of dimethoxycurcumin

NASA Astrophysics Data System (ADS)

Arrue, Lily; Barra, Tomas; Camarada, María Belén; Zarate, Ximena; Schott, Eduardo

2017-06-01

Dimethoxycurcumin (DMC) ((1E,6E)-1-(3,4-dimethoxycyclohexyl)-7-(3,4-dimethoxyphenyl) hepta-1,6- diene-3,5-dione) is a natural polyphenolic compound that appears together with curcumin in turmeric. Both molecules have wide range biological activities as antioxidant, anti-inflammatory and anti-carcinogenic agent. To evaluate the oxidation process and kinetics for DMC, the rate constant, electron transfer and diffusion coefficients for the electrochemical oxidation were determined. Therefore, its electrochemical behavior over a platinum electrode in anhydrous media was investigated. Furthermore, DFT calculations were performed to give a rational explanation to the obtained results. All the results support the fact that the central sbnd CH2sbnd group is the most reactive against an oxidation process.

Production, purification, and properties of a lipase from a bacterium (Pseudomonas aeruginosa YS-7) capable of growing in water-restricted environments.

PubMed Central

Shabtai, Y; Daya-Mishne, N

1992-01-01

An extracellular lipase from the low-water-tolerant bacterium P. aeruginosa YS-7 was produced, purified, and characterized with respect to its functional properties in aqueous solutions and organic solvents. The enzyme was partially released from the cells during fermentation in defined medium with 5% (wt/vol) soybean oil. Approximately one-half of the total culture activity remained in solution after removal of cells. More than 95% of the activity was found in culture supernatant after mild detergent treatment (10 mM sodium deoxycholate) or after shifting the carbon source during the fermentation from triglyceride to a free fatty acid. The enzyme was recovered from an acetone precipitate of the whole culture and purified by hydrophobic interaction chromatography, yielding a preparation having a specific activity of about 1,300 mumol of fatty acid mg-1 h-1. The lipase (molecular size, approximately 40 kDa) hydrolyzes a variety of fatty acid esters and has an optimum pH of about 7. The enzyme retained its full activity at 20 to 55 degrees C, even after prolonged exposure (more than 30 days) to different concentrations of water-miscible organic solvents such as alcohols, glycols, pyridine, acetonitrile, dimethyl formamide, and dimethyl sulfoxide. The hydrolysis of 4-nitrophenyl laurate ester and of triglyceride emulsified in water was slightly accelerated with increasing concentrations of alcohols and glycols up to about 20% but was abolished with a further increase in alcohol concentration or in the presence of acetonitrile. In contrast, the rate of hydrolysis of these substrates in concentrated solutions of dimethyl formamide or dimethyl sulfoxide was markedly increased, by more than twofold and more than fivefold, respectively.(ABSTRACT TRUNCATED AT 250 WORDS) Images PMID:1539972

Dihydropteridine/pteridine as a 2H +/2e – redox mediator for the reduction of CO 2 to methanol: A computational study

DOE PAGES

Lim, Chern -Hooi; Holder, Aaron M.; Hynes, James T.; ...

2017-04-04

Conflicting experimental results for the electrocatalytic reduction of CO 2 to CH 3OH on a glassy carbon electrode by the 6,7-dimethyl-4-hydroxy-2-mercaptopteridine have been recently reported. In this study, we have used computational chemistry to examine the issue of this molecule's ability to act as a hydride donor to reduce CO 2.

Spectrophotometric determination of copper in alkaline solutions and evaluation of some hydroxy-substituted 1,10-phenanthrolines as chromogenic reagents.

PubMed

Dunbar, W E; Schilt, A A

1972-09-01

Seven new hydroxy-substituted 1,10-phenanthroline derivatives have been evaluated as chromogenic reagents for the determination of copper in strongly alkaline solution. The most sensitive of these, 2,9-dimethyl-4,7-dihydroxy-1,10-phenanthroline, has proven to be highly effective in a simple, rapid procedure for determining trace amounts of copper in sodium hydroxide, potassium carbonate, sodium phosphate or ammonium hydroxide.

Synthesis and biological studies of positron-emitting radiopharmaceuticals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dischino, D.D.

The development and clinical evaluation of two-positron emitting radiopharmaceuticals designed to image myelin in humans is reported. Carbon-11-labeled benzyl methyl ether was synthesized by the reaction of carbon-11-labeled methanol and benzyl chloride in dimethyl sulfoxide containing powdered potassium hydroxide in a radiochemical yield of 43% and a synthesis and purification time of 40 minutes. Carbon-11-labeled diphenylmethanol was synthesized by the reaction of carbon-11-labeled carbon dioxide and phenyllithium followed by the reduction of the carbon-11-labeled intermediate to diphenylmethanol via lithium aluminum hydride in a radiochemical yield of 71% and a synthesis and purification time of 38 minutes. Carbon-11-labeled benzyl methyl ethermore » and diphenylmethanol were each evaluated as myelin imaging agents in three patients with multiple sclerosis via positron-emission tomography. In two out of three patients studied with carbon-11-labeled benzyl methyl ether, the distribution of activity in the brain was not consistent with local lipid content. A new synthesis of carbon-11-labeled-DL-phenylalanine labeled in the benzylic position and the synthesis of fluorine-18-labeled 1-(2-nitro-1-imidazolyl)-3-fluoro-2-propanol, a potential in vivo marker of hypoxic tissue, are reported.« less

Structure elucidation of the designer drug N-(1-amino-3,3-dimethyl-1-oxobutan-2-yl)-1-(5-fluoropentyl)-3-(4-fluorophenyl)-pyrazole-5-carboxamide and the relevance of predicted (13) C NMR shifts - a case study.

PubMed

Girreser, Ulrich; Rösner, Peter; Vasilev, Andrej

2016-07-01

The detailed structure elucidation process of the new cannabimimetic designer drug, N-(1-amino-3,3-dimethyl-1-oxobutan-2-yl)-1-(5-fluoropentyl)-3-(4-fluorophenyl)-pyrazole-5-carboxamide, with a highly substituted pyrazole skeleton, using nuclear magnetic resonance (NMR) spectroscopic and mass spectrometric (MS) techniques is described. After a first analysis of the NMR spectra and comparison with 48 possible pyrazole and imidazole structures, a subset of six positional isomeric pyrazoles and six imidazoles remained conceivable. Four substituents of the heterocyclic skeleton were identified: a proton bound to a pyrazole ring carbon atom; a 5-fluoropentyl group; a 4-fluorophenyl substituent; and a carbamoyl group, which is N-substituted with a methyl residue carrying a tert.-butyl and a carbamoyl substituent. The 5-fluoropentyl residue is situated at the nitrogen ring atom. Additional NMR experiments like the (1) H,(13) C HMBC were performed, but due to the small number of signals based on long-range couplings, the comparison of predicted and observed (13) C chemical shifts became necessary. The open access Internet shift prediction programs NMRDB, NMRSHIFTDB2, and CSEARCH were employed for the prediction of (13) C shift values which allowed an efficient and unambiguous structure determination. For the identified N-(1-amino-3,3-dimethyl-1-oxobutan-2-yl)-1-(5-fluoropentyl)-3-(4-fluorophenyl)-pyrazole-5-carboxamide, the best agreement between predicted (13) C shifts and the observed chemical shifts and long-range couplings for the pyrazole ring carbon atoms, with a standard error of about 2 ppm, was found with each of the predictions. For the comparison of measured and predicted chemical shifts model compounds with simple substituents proved helpful. The identified compound is a homologue of AZ-037 which is offered by Internet suppliers. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Helical filaments of human Dmc1 protein on single-stranded DNA: a cautionary tale

PubMed Central

Yu, Xiong; Egelman, Edward H.

2010-01-01

Proteins in the RecA/Rad51/RadA family form nucleoprotein filaments on DNA that catalyze a strand exchange reaction as part of homologous genetic recombination. Because of the centrality of this system to many aspects of DNA repair, the generation of genetic diversity, and cancer when this system fails or is not properly regulated, these filaments have been the object of many biochemical and biophysical studies. A recent paper has argued that the human Dmc1 protein, a meiotic homolog of bacterial RecA and human Rad51, forms filaments on single stranded DNA with ∼ 9 subunits per turn in contrast to the filaments formed on double stranded DNA with ∼ 6.4 subunits per turn, and that the stoichiometry of DNA binding is different between these two filaments. We show using scanning transmission electron microscopy (STEM) that the Dmc1 filament formed on single stranded DNA has a mass per unit length expected from ∼ 6.5 subunits per turn. More generally, we show how ambiguities in helical symmetry determination can generate incorrect solutions, and why one sometimes must use other techniques, such as biochemistry, metal shadowing, or STEM to resolve these ambiguities. While three-dimensional reconstruction of helical filaments from EM images is a powerful tool, the intrinsic ambiguities that may be present with limited resolution are not sufficiently appreciated. PMID:20600108

MUSTANG: A Community-Facing Web Service to Improve Seismic Data Quality Awareness Through Metrics

NASA Astrophysics Data System (ADS)

Templeton, M. E.; Ahern, T. K.; Casey, R. E.; Sharer, G.; Weertman, B.; Ashmore, S.

2014-12-01

IRIS DMC is engaged in a new effort to provide broad and deep visibility into the quality of data and metadata found in its terabyte-scale geophysical data archive. Taking advantage of large and fast disk capacity, modern advances in open database technologies, and nimble provisioning of virtual machine resources, we are creating an openly accessible treasure trove of data measurements for scientists and the general public to utilize in providing new insights into the quality of this data. We have branded this statistical gathering system MUSTANG, and have constructed it as a component of the web services suite that IRIS DMC offers. MUSTANG measures over forty data metrics addressing issues with archive status, data statistics and continuity, signal anomalies, noise analysis, metadata checks, and station state of health. These metrics could potentially be used both by network operators to diagnose station problems and by data users to sort suitable data from unreliable or unusable data. Our poster details what MUSTANG is, how users can access it, what measurements they can find, and how MUSTANG fits into the IRIS DMC's data access ecosystem. Progress in data processing, approaches to data visualization, and case studies of MUSTANG's use for quality assurance will be presented. We want to illustrate what is possible with data quality assurance, the need for data quality assurance, and how the seismic community will benefit from this freely available analytics service.

Stroop proactive control and task conflict are modulated by concurrent working memory load.

PubMed

Kalanthroff, Eyal; Avnit, Amir; Henik, Avishai; Davelaar, Eddy J; Usher, Marius

2015-06-01

Performance on the Stroop task reflects two types of conflict-informational (between the incongruent word and font color) and task (between the contextually relevant color-naming task and the irrelevant, but automatic, word-reading task). According to the dual mechanisms of control theory (DMC; Braver, 2012), variability in Stroop performance can result from variability in the deployment of a proactive task-demand control mechanism. Previous research has shown that when proactive control (PC) is diminished, both increased Stroop interference and a reversed Stroop facilitation (RF) are observed. Although the current DMC model accounts for the former effect, it does not predict the observed RF, which is considered to be behavioral evidence for task conflict in the Stroop task. Here we expanded the DMC model to account for Stroop RF. Assuming that a concurrent working memory (WM) task reduces PC, we predicted both increased interference and an RF. Nineteen participants performed a standard Stroop task combined with a concurrent n-back task, which was aimed at reducing available WM resources, and thus overloading PC. Although the results indicated common Stroop interference and facilitation in the low-load condition (zero-back), in the high-load condition (two-back), both increased Stroop interference and RF were observed, consistent with the model's prediction. These findings indicate that PC is modulated by concurrent WM load and serves as a common control mechanism for both informational and task Stroop conflicts.

Electron impact dissociation of amorphous cis-methyl acetate ice analogs

NASA Astrophysics Data System (ADS)

Sivaraman, B.; Mukherjee, R.; Subramanian, K. P.; Banerjee, S. B.

2014-08-01

We have carried out, for the first time, electron irradiation on methyl acetate (CH3COOCH3) ices grown, under astrochemical condition, at 85 K and the chemical changes were probed by FTIR spectroscopy in the mid-IR region (4000-500 cm-1). Carbon dioxide (CO2), carbon monoxide (CO) molecules were found to be the major products indicating a competing dissociation pathway along with the by-products ethane (C2H6) and dimethyl ether (CH3OCH3), respectively. CH3OH (methyl alcohol) formation showed the possibility of acetate to alcohol conversion by keV electron irradiation. In addition irradiation induced aggregation of CH3COOCH3 molecules is also proposed.

Characterization of the International Humic Substances Society standard and reference fulvic and humic acids by solution state carbon-13 (13C) and hydrogen-1 (1H) nuclear magnetic resonance spectrometry

USGS Publications Warehouse

Thorn, Kevin A.; Folan, Daniel W.; MacCarthy, Patrick

1989-01-01

Standard and reference samples of the International Humic Substances Society have been characterized by solution state carbon-13 and hydrogen-1 nuclear magnetic resonance (NMR) spectrometry. Samples included the Suwannee River, soil, and peat standard fulvic and humic acids, the Leonardite standard humic acid, the Nordic aquatic reference fulvic and humic acids, and the Summit Hill soil reference humic acid. Aqueous-solution carbon-13 NMR analyses included the measurement of spin-lattice relaxation times, measurement of nuclear Overhauser enhancement factors, measurement of quantitative carbon distributions, recording of attached proton test spectra, and recording of spectra under nonquantitative conditions. Distortionless enhancement by polarization transfer carbon-13 NMR spectra also were recorded on the Suwannee River fulvic acid in deuterated dimethyl sulfoxide. Hydrogen-1 NMR spectra were recorded on sodium salts of the samples in deuterium oxide. The carbon aromaticities of the samples ranged from 0.24 for the Suwannee River fulvic acid to 0.58 for the Leonardite humic acid.

Hindered Glymes for Graphite-Compatible Electrolytes.

PubMed

Shanmukaraj, Devaraj; Grugeon, Sylvie; Laruelle, Stephane; Armand, Michel

2015-08-24

Organic carbonate mixtures are used almost exclusively as lithium battery electrolyte solvents. The linear compounds (dimethyl carbonate, diethyl carbonate, ethyl methyl carbonate) act mainly as thinner for the more viscous and high-melting ethylene carbonate but are the least stable component and have low flash points; these are serious handicaps for lifetime and safety. Polyethers (glymes) are useful co-solvents, but all formerly known representatives solvate Li(+) strongly enough to co-intercalate in the graphite negative electrode and exfoliate it. We have put forward a new electrolyte composition comprising a polyether to which a bulky tert-butyl group is attached ("hindered glyme"), thus completely preventing co-intercalation while maintaining good conductivity. This alkyl-carbonate-free electrolyte shows remarkable cycle efficiency of the graphite electrode, not only at room temperature, but also at 50 and 70 °C in the presence of lithium bis(fluorosulfonimide). The two-ethylene-bridge hindered glyme has a high boiling point and a flash point of 80 °C, a considerable advantage for safety. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The IRIS Data Management Center: Enabling Access to Observational Time Series Spanning Decades

NASA Astrophysics Data System (ADS)

Ahern, T.; Benson, R.; Trabant, C.

2009-04-01

The Incorporated Research Institutions for Seismology (IRIS) is funded by the National Science Foundation (NSF) to operate the facilities to generate, archive, and distribute seismological data to research communities in the United States and internationally. The IRIS Data Management System (DMS) is responsible for the ingestion, archiving, curation and distribution of these data. The IRIS Data Management Center (DMC) manages data from more than 100 permanent seismic networks, hundreds of temporary seismic deployments as well as data from other geophysical observing networks such as magnetotelluric sensors, ocean bottom sensors, superconducting gravimeters, strainmeters, surface meteorological measurements, and in-situ atmospheric pressure measurements. The IRIS DMC has data from more than 20 different types of sensors. The IRIS DMC manages approximately 100 terabytes of primary observational data. These data are archived in multiple distributed storage systems that insure data availability independent of any single catastrophic failure. Storage systems include both RAID systems of greater than 100 terabytes as well as robotic tape robots of petabyte capacity. IRIS performs routine transcription of the data to new media and storage systems to insure the long-term viability of the scientific data. IRIS adheres to the OAIS Data Preservation Model in most cases. The IRIS data model requires the availability of metadata describing the characteristics and geographic location of sensors before data can be fully archived. IRIS works with the International Federation of Digital Seismographic Networks (FDSN) in the definition and evolution of the metadata. The metadata insures that the data remain useful to both current and future generations of earth scientists. Curation of the metadata and time series is one of the most important activities at the IRIS DMC. Data analysts and an automated quality assurance system monitor the quality of the incoming data. This insures data are of acceptably high quality. The formats and data structures used by the seismological community are esoteric. IRIS and its FDSN partners are developing web services that can transform the data holdings to structures that are more easily used by broader scientific communities. For instance, atmospheric scientists are interested in using global observations of microbarograph data but that community does not understand the methods of applying instrument corrections to the observations. Web processing services under development at IRIS will transform these data in a manner that allows direct use within such analysis tools as MATLAB® already in use by that community. By continuing to develop web-service based methods of data discovery and access, IRIS is enabling broader access to its data holdings. We currently support data discovery using many of the Open Geospatial Consortium (OGC) web mapping services. We are involved in portal technologies to support data discovery and distribution for all data from the EarthScope project. We are working with computer scientists at several universities including the University of Washington as part of a DataNet proposal and we intend to enhance metadata, further develop ontologies, develop a Registry Service to aid in the discovery of data sets and services, and in general improve the semantic interoperability of the data managed at the IRIS DMC. Finally IRIS has been identified as one of four scientific organizations that the External Research Division of Microsoft wants to work with in the development of web services and specifically with the development of a scientific workflow engine. More specific details of current and future developments at the IRIS DMC will be included in this presentation.

Physical Properties of Substituted Imidazolium Based Ionic Liquids Gel Electrolytes

NASA Astrophysics Data System (ADS)

Sutto, Thomas E.; De Long, Hugh C.; Trulove, Paul C.

2002-11-01

The physical properties of solid gel electrolytes of either polyvinylidene diflurohexafluoropropylene or a combination of polyvinylidene hexafluoropropylene and polyacrylic acid, and the molten salts 1-ethyl-3-methylimidazolium tetrafluoroborate, 1,2-dimethyl-3-n-propylimidazolium tetrafluoroborate, and the new molten salts 1,2-dimethyl-3-n-butylimidazolium tetrafluoroborate, and 1,2-dimethyl-3-n-butylimidazolium hexafluorophosphate were characterized by temperature dependent ionic conductivity measurements for both the pure molten salt and of the molten salt with 0.5 M Li+ present. Ionic conductivity data indicate that for each of the molten salts, the highest concentration of molten salt allowable in a single component polymer gel was 85%, while gels composed of 90%molten salt were possible when using both polyvinylidene hexafluorophosphate and polyacrylic acid. For polymer gel composites prepared using lithium containing ionic liquids, the optimum polymer gel composite consisted of 85% of the 0.5 M Li+/ionic liquid, 12.75% polyvinylidene hexafluoropropylene, and 2.25% poly (1-carboxyethylene). The highest ionic conductivity observed was for the gel containing 90%1-ethyl-3-methyl-imidazolium tetrafluoroborate, 9.08 mS/cm. For the lithium containing ionic liquid gels, their ionic conductivity ranged from 1.45 to 0.05 mS/cm, which is comparable to the value of 0.91 mS/cm, observed for polymer composite gels containing 0.5 M LiBF4 in propylene carbonate.

Brief communication: economic comparison of opportunistic infection management with antiretroviral treatment in people living with HIV/AIDS presenting at an NGO clinic in Bangalore, India.

PubMed

John, K R; Rajagopalan, Nirmala; Madhuri, K V

2006-11-01

Highly active antiretroviral treatment (HAART) usage in India is escalating. With the government of India launching the free HAART rollout as part of the "3 by 5" initiative, many people living with HIV/AIDS (PLHA) have been able to gain access to HAART medications. Currently, the national HAART centers are located in a few district hospitals (in the high- and medium-prevalence states) and have very stringent criteria for enrolling PLHA. Patients who do not fit these criteria or patients who are too ill to undergo the prolonged wait at the government hospitals avail themselves of nongovernment organization (NGO) services in order to take HAART medications. In addition, the government program has not yet started providing second-line HAART (protease inhibitors). Hence, even with the free HAART rollout, NGOs with the expertise to provide HAART continue to look for funding opportunities and other innovative ways of making HAART available to PLHA. Currently, no study from Indian NGOs has compared the direct and indirect costs of solely managing opportunistic infections (OIs) vs HAART. Compare direct medical costs (DMC) and nonmedical costs (NMC) with 2005 values accrued by the NGO and PLHA, respectively, for either HAART or exclusive OI management. Retrospective case study comparison. Low-cost community care and support center--Freedom Foundation (NGO, Bangalore, south India). Retrospective analysis data on PLHA accessing treatment at Freedom Foundation between January 1, 2003 and January 1, 2005. The HAART arm included case records of PLHA who initiated HAART at the center, had frequent follow-up, and were between 18 and 55 years of age. The OI arm included records of PLHA who were also frequently followed up, who were in the same age range, who had CD4+ cell counts < 200/microliter (mcL) or an AIDS-defining illness, and who were not on HAART (solely for socioeconomic reasons). A total of 50 records were analyzed. Expenditures on medication, hospitalization, diagnostics, and NMC (such as food and travel for a caregiver) were calculated for each group. At 2005 costs, the median DMC plus NMC in the OI group was 21,335 Indian rupees (Rs) (mean Rs 24,277/-) per patient per year (pppy) (US $474). In the HAART group, the median DMC plus NMC was Rs 18,976/- (mean Rs 21,416/-) pppy (US $421). Median DMC plus NMC pppy in the OI arm was Rs 13623.7/- paid by NGO and Rs 1155/- paid by PLHA. Median DMC and NMC pppy in the HAART arm were Rs 1425/- paid by NGO and Rs 17,606/- paid by PLHA. Good health at no increased expenditure justifies providing PLHA with HAART even in NGO settings.

The GEON Integrated Data Viewer (IDV) and IRIS DMC Services Illustrate CyberInfrastructure Support for Seismic Data Visualization and Interpretation

NASA Astrophysics Data System (ADS)

Meertens, C.; Wier, S.; Ahern, T.; Casey, R.; Weertman, B.; Laughbon, C.

2008-12-01

UNAVCO and the IRIS DMC are data service partners for seismic visualization, particularly for hypocentral data and tomography. UNAVCO provides the GEON Integrated Data Viewer (IDV), an extension of the Unidata IDV, a free, interactive, research-level, software display and analysis tool for data in 3D (latitude, longitude, depth) and 4D (with time), located on or inside the Earth. The GEON IDV is designed to meet the challenge of investigating complex, multi-variate, time-varying, three- dimensional geoscience data in the context of new remote and shared data sources. The GEON IDV supports data access from data sources using HTTP and FTP servers, OPeNDAP servers, THREDDS catalogs, RSS feeds, and WMS (web map) servers. The IRIS DMC (Data Management System) has developed web services providing data for earthquake hypocentral data and seismic tomography model grids. These services can be called by the GEON IDV to access data at IRIS without copying files. The IRIS Earthquake Browser (IEB) is a web-based query tool for hypocentral data. The IEB combines the DMC's large database of more than 1,900,000 earthquakes with the Google Maps web interface. With the IEB you can quickly find earthquakes in any region of the globe and then import this information into the GEON Integrated Data Viewer where the hypocenters may be visualized. You can select earthquakes by location region, time, depth, and magnitude. The IEB gives the IDV a URL to the selected data. The IDV then shows the data as maps or 3D displays, with interactive control of vertical scale, area, map projection, with symbol size and color control by magnitude or depth. The IDV can show progressive time animation of, for example, aftershocks filling a source region. The IRIS Tomoserver converts seismic tomography model output grids to NetCDF for use in the IDV. The Tomoserver accepts a tomographic model file as input from a user and provides an equivalent NetCDF file as output. The service supports NA04, S3D, A1D and CUB input file formats, contributed by their respective creators. The NetCDF file is saved to a location that can be referenced with a URL on an IRIS server. The URL for the NetCDF file is provided to the user. The user can download the data from IRIS, or copy the URL into IDV directly for interpretation, and the IDV will access the data at IRIS. The Tomoserver conversion software was developed by Instrumental Software Technologies, Inc. Use cases with the GEON IDV and IRIS DMC data services will be shown.

SYNTHESIS AND EVALUATION OF NEW PHTHALAZINE SUBSTITUTED β-LACTAM DERIVATIVES AS CARBONIC ANHYDRASE INHIBITORS.

PubMed

Berber, Nurcan; Arslan, Mustafa; Bilen, Çiğdem; Sackes, Zübeyde; Gençer, Nahit; Arslan, Oktay

2015-01-01

A new series of phthalazine substituted β-lactam derivatives were synthesized and their inhibitory effects on the activity of purified human carbonic anhydrase (hCA I and II) were evaluated. 2H-Indazolo[2,1-b]phthala- zine-trione derivative was prepared with 4-nitrobenzaldehyde, dimedone, and phthalhydrazide in the presence of TFA in DMF, and the nitro group was reduced to 13-(4-aminophenyl)-3,3-dimethyl-3,4-dihydro- 2H-indazolo[1,2-b]phthalazine-1,6,11(13H)-trione with SnCl2 · 2H2O. The reduced compound was re- acted with different aromatic aldehydes, and phthalazine substituted imines were synthesized. The imine compounds undergo (2+2) cycloaddition reactions with ketenes to produce 2H-indazolo[2,1-b]phthala-zine-trione substituted β-lactam derivatives. The β-lactam compounds were tested as inhibitors of the CA isoenzyme activity. The results showed that all the synthesized compounds inhibited the CA isoenzyme activity. 1-(4-(3,3-dimethyl- 1,6,1 1-trioxo-2,3,4,6,11,13-hexahydro-1H-indazolo[1,2-b]phthalazin-13- yl)phenyl)-2-oxo-4-p-tolylazetidin-3-yl acetate (IC50 = 6.97 µM for hCA I and 8.48 µM for hCA II) had the most inhibitory effect.

Aerobic and anaerobic degradation of a range of alkyl sulfides by a denitrifying marine bacterium

USGS Publications Warehouse

Visscher, P.T.; Taylor, B.F.

1993-01-01

A pure culture of a bacterium was obtained from a marine microbial mat by using an anoxic medium containing dimethyl sulfide (DMS) and nitrate. The isolate grew aerobically or anaerobically as a denitrifier on alkyl sulfides, including DMS, dimethyl disulfide, diethyl sulfide (DES), ethyl methyl sulfide, dipropyl sulfide, dibutyl sulfide, and dibutyl disulfide. Cells grown on an alkyl sulfide or disulfide also oxidized the corresponding thiols, namely, methanethiol, ethanethiol, propanethiol, or butanethiol. Alkyl sulfides were metabolized by induced or derepressed cells with oxygen, nitrate, or nitrite as electron acceptor. Cells grown on DMS immediately metabolized DMS, but there was a lag before DES was consumed; with DES-grown cells, DES was immediately used but DMS was used only after a lag. Chloramphenicol prevented the eventual use of DES by DMS-grown cells and DMS use by DES-grown cells, respectively, indicating separate enzymes for the metabolism of methyl and ethyl groups. Growth was rapid on formate, acetate, propionate, and butyrate but slow on methanol. The organism also grew chemolithotrophically on thiosulfate with a decrease in pH; growth required carbonate in the medium. Growth on sulfide was also carbonate dependent but slow. The isolate was identified as a Thiobacillus sp. and designated strain ASN-1. It may have utility for removing alkyl sulfides, and also nitrate, nitrite, and sulfide, from wastewaters.

Anaerobic electron acceptor chemotaxis in Shewanella putrefaciens

NASA Technical Reports Server (NTRS)

Nealson, K. H.; Moser, D. P.; Saffarini, D. A.

1995-01-01

Shewanella putrefaciens MR-1 can grow either aerobically or anaerobically at the expense of many different electron acceptors and is often found in abundance at redox interfaces in nature. Such redox interfaces are often characterized by very strong gradients of electron acceptors resulting from rapid microbial metabolism. The coincidence of S. putrefaciens abundance with environmental gradients prompted an examination of the ability of MR-1 to sense and respond to electron acceptor gradients in the laboratory. In these experiments, taxis to the majority of the electron acceptors that S. putrefaciens utilizes for anaerobic growth was seen. All anaerobic electron acceptor taxis was eliminated by the presence of oxygen, nitrate, nitrite, elemental sulfur, or dimethyl sulfoxide, even though taxis to the latter was very weak and nitrate and nitrite respiration was normal in the presence of dimethyl sulfoxide. Studies with respiratory mutants of MR-1 revealed that several electron acceptors that could not be used for anaerobic growth nevertheless elicited normal anaerobic taxis. Mutant M56, which was unable to respire nitrite, showed normal taxis to nitrite, as well as the inhibition of taxis to other electron acceptors by nitrite. These results indicate that electron acceptor taxis in S. putrefaciens does not conform to the paradigm established for Escherichia coli and several other bacteria. Carbon chemo-taxis was also unusual in this organism: of all carbon compounds tested, the only positive response observed was to formate under anaerobic conditions.

Carbon nanotube (CNT) and nanofibrillated cellulose (NFC) reinforcement effect on thermoplastic polyurethane (TPU) scaffolds fabricated via phase separation using dimethyl sulfoxide (DMSO) as solvent.

PubMed

Mi, Hao-Yang; Jing, Xin; Salick, Max R; Cordie, Travis M; Turng, Lih-Sheng

2016-09-01

Although phase separation is a simple method of preparing tissue engineering scaffolds, it suffers from organic solvent residual in the scaffold. Searching for nontoxic solvents and developing effective solvent removal methods are current challenges in scaffold fabrication. In this study, thermoplastic polyurethane (TPU) scaffolds containing carbon nanotubes (CNTs) or nanofibrillated cellulose fibers (NFCs) were prepared using low toxicity dimethyl sulfoxide (DMSO) as a solvent. The effects of two solvent removal approaches on the final scaffold morphology were studied. The freeze drying method caused large pores, with small pores on the pore walls, which created connections between the pores. Meanwhile, the leaching and freeze drying method led to interconnected fine pores with smaller pore diameters. The nucleation effect of CNTs and the phase separation behavior of NFCs in the TPU solution resulted in significant differences in the microstructures of the resulting scaffolds. The mechanical performance of the nanocomposite scaffolds with different morphologies was investigated. Generally, the scaffolds with a fine pore structure showed higher compressive properties, and both the CNTs and NFCs improved the compressive properties of the scaffolds, with greater enhancement found in TPU/NFC nanocomposite scaffolds. In addition, all scaffolds showed good sustainability under cyclical load bearing, and the biocompatibility of the scaffolds was verified via 3T3 fibroblast cell culture. Copyright © 2016 Elsevier Ltd. All rights reserved.

Operational overview of the NASA GTE/CITE 3 airborne instrument intercomparisons for sulfur dioxide, hydrogen sulfide, carbonyl sulfide, dimethyl sulfide, and carbon disulfide

NASA Technical Reports Server (NTRS)

Hoell, James M., Jr.; Davis, Douglas D.; Gregory, Gerald L.; Mcneal, Robert J.; Bendura, Richard J.; Drewry, Joseph W.; Barrick, John D.; Kirchhoff, Volker W. J. H.; Motta, Adauto G.; Navarro, Roger L.

1993-01-01

This paper reports the overall experimental design and gives a brief overview of results from the third airborne Chemical Instrumentation Test and Evaluation (CITE 3) mission conducted as part of the National Aeronautics and Space Administration's Global Tropospheric Experiment. The primary objective of CITE 3 was to evaluate the capability of instrumentation for airborne measurements of ambient concentrations of SO2, H2S, CS, dimethyl sulfide, and carbonyl sulfide. Ancillary measurements augmented the intercomparison data in order to address the secondary objective of CITE 3 which was to address specific issues related to the budget and photochemistry of tropospheric sulfur species. The CITE 3 mission was conducted on NASA's Wallops Flight Center Electra aircraft and included a ground-based intercomparison of sulfur standards and intercomparison/sulfur science flights conducted from the NASA Wallops Flight Facility, Wallops Island, Virginia, followed by flights from Natal, Brazil. Including the transit flights, CITE 3 included 16 flights encompassing approximately 96 flight hours.

Aprotic solvents effect on the UV-visible absorption spectra of bixin.

PubMed

Rahmalia, Winda; Fabre, Jean-François; Usman, Thamrin; Mouloungui, Zéphirin

2014-10-15

We describe here the effects of aprotic solvents on the spectroscopic characteristics of bixin. Bixin was dissolved in dimethyl sulfoxide, acetone, dichloromethane, ethyl acetate, chloroform, dimethyl carbonate, cyclohexane and hexane, separately, and its spectra in the resulting solutions were determined by UV-visible spectrophotometry at normal pressure and room temperature. We analyzed the effect of aprotic solvents on λmax according to Onsager cavity model and Hansen theory, and determined the approximate absorption coefficient with the Beer-Lambert law. We found that the UV-visible absorption spectra of bixin were found to be solvent dependent. The S0→S2 transition energy of bixin in solution was dependent principally on the refractive index of the solvents and the bixin-solvent dispersion interaction. There was a small influence of the solvents dielectric constant, permanent dipole interaction and hydrogen bonding occurred between bixin and solvents. The absorbance of bixin in various solvents, with the exception of hexane, increased linearly with concentration. Copyright © 2014 Elsevier B.V. All rights reserved.

Aprotic solvents effect on the UV-visible absorption spectra of bixin

NASA Astrophysics Data System (ADS)

Rahmalia, Winda; Fabre, Jean-François; Usman, Thamrin; Mouloungui, Zéphirin

2014-10-01

We describe here the effects of aprotic solvents on the spectroscopic characteristics of bixin. Bixin was dissolved in dimethyl sulfoxide, acetone, dichloromethane, ethyl acetate, chloroform, dimethyl carbonate, cyclohexane and hexane, separately, and its spectra in the resulting solutions were determined by UV-visible spectrophotometry at normal pressure and room temperature. We analyzed the effect of aprotic solvents on λmax according to Onsager cavity model and Hansen theory, and determined the approximate absorption coefficient with the Beer-Lambert law. We found that the UV-visible absorption spectra of bixin were found to be solvent dependent. The S0 → S2 transition energy of bixin in solution was dependent principally on the refractive index of the solvents and the bixin-solvent dispersion interaction. There was a small influence of the solvents dielectric constant, permanent dipole interaction and hydrogen bonding occurred between bixin and solvents. The absorbance of bixin in various solvents, with the exception of hexane, increased linearly with concentration.

(Carbonato-κ2 O,O′)bis­(5,5′-dimethyl-2,2′-bipyridyl-κ2 N,N′)cobalt(III) bromide trihydrate

PubMed Central

Arun Kumar, Kannan; Meera, Parthsarathi; Amutha Selvi, Madhavan; Dayalan, Arunachalam

2012-01-01

In the title complex, [Co(CO3)(C12H12N2)2]Br·3H2O, the CoIII cation has a distorted octa­hedral coordination environment. It is chelated by four N atoms of two different 5,5′-dimethyl-2,2′-bipyridyl (dmbpy) ligands in axial and equatorial positions, and by two O atoms of a carbonate anion completing the equatorial positions. Although the water mol­ecules are disordered and their H atoms were not located, there are typical O⋯O distances between 2.8 and 3.0 Å, indicating O—H⋯O hydrogen bonding. The crystal packing is consolidated by C—H⋯O and C—H⋯Br hydrogen bonds, as well as π–π stacking inter­actions between adjacent pyridine rings of the dmbpy ligands, with centroid–centroid distances of 3.694 (3) and 3.7053 (3) Å. PMID:22589773

(Carbonato-κ(2)O,O')bis-(5,5'-dimethyl-2,2'-bipyridyl-κ(2)N,N')cobalt(III) bromide trihydrate.

PubMed

Arun Kumar, Kannan; Meera, Parthsarathi; Amutha Selvi, Madhavan; Dayalan, Arunachalam

2012-04-01

In the title complex, [Co(CO(3))(C(12)H(12)N(2))(2)]Br·3H(2)O, the Co(III) cation has a distorted octa-hedral coordination environment. It is chelated by four N atoms of two different 5,5'-dimethyl-2,2'-bipyridyl (dmbpy) ligands in axial and equatorial positions, and by two O atoms of a carbonate anion completing the equatorial positions. Although the water mol-ecules are disordered and their H atoms were not located, there are typical O⋯O distances between 2.8 and 3.0 Å, indicating O-H⋯O hydrogen bonding. The crystal packing is consolidated by C-H⋯O and C-H⋯Br hydrogen bonds, as well as π-π stacking inter-actions between adjacent pyridine rings of the dmbpy ligands, with centroid-centroid distances of 3.694 (3) and 3.7053 (3) Å.

Can cemented dual-mobility cups be used without a reinforcement device in cases of mild acetabular bone stock alteration in total hip arthroplasty?

PubMed

Haen, T X; Lonjon, G; Vandenbussche, E

2015-12-01

Cemented versions of dual-mobility cups (DMCs), helpful in cases of bone stock alteration, are usually used in association with a reinforcement device. To simplify the intervention in elderly subjects or those with a poor bone stock, the cups can be cemented directly into the bone, but the long-term result remains uncertain. We conducted a retrospective study in this population so as to: (1) assess whether cemented fixation of a DMC without a reinforcement device leads to a higher loosening rate, (2) confirm its efficacy in preventing dislocations in subjects at high risk of instability, and (3) measure the functional results. Cemented fixation of a DMC is reliable in cases of moderate alteration of bone stock. Sixty-four patients (66 hips) undergoing implantation of a cemented DMC (Saturne™) without a reinforcement device were included in this single-center retrospective study. Their mean age was 79.8 years (range, 40-95 years). The indications varied: hip osteoarthritis (30.3%), prosthesis revision (44.0%), and trauma (25.8%). The patients were evaluated radiologically and clinically at follow-up. The main evaluation criterion was the revision rate for aseptic loosening. Dislocations, the infection rate, and the Postel Merle d'Aubigné (PMA) score were noted. At the mean follow-up of 4.2 years, three (4.6%) patients had been lost to follow-up and 22 (33.3%) had died. There was one case of aseptic loosening (1.5%). Cup survival was 98% at 5 years (95%CI [94-100]). There were no dislocations. There was one revision for infection. The mean PMA score was 15.5 (range, 9-18). The frequency of acetabular loosening was comparable to the frequency in cemented DMCs with a reinforcement device. A cemented DMC without a reinforcement device is possible and is a simple and viable option when there is moderate bone stock alteration. IV, retrospective cohort study. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

New data products available at the IRIS DMC

NASA Astrophysics Data System (ADS)

Trabant, C. M.; Bahavar, M.; Hutko, A.; Karstens, R.

2010-12-01

The research supported by the raw data from the observatories of NSF's EarthScope project are having tremendous impact on our understanding of the structure and geologic history of North America, how and why earthquakes occur and many other areas of modern geophysics. The IRIS Data Management Center (DMC) is the primary access point for EarthScope/USArray data and has embarked on a new effort to produce higher-level data products beyond raw time series in order to assist the community in extracting the highest value possible from these data. These new products will serve many purposes: stepping-stones for future research projects, data visualizations, research result comparisons and compilation of unique data sets as well as outreach material. To ensure community involvement in the development of new products the requirements and priorities are reviewed and approved by the IRIS Data Products Working Group (DPWG). Many new products are now available at the IRIS DMC. These include two event based products generated in near real time. 1) USArray Ground Motion Visualizations, routinely generated animations showing the both the vertical and horizontal seismic wavefields sweeping across the USArray Transportable Array from earthquakes around the world. 2) Event Plots, a suite of figures automatically generated following all M6.0+ events which include phase aligned record sections, global body wave envelope stacks, regional network vespagrams and source-time functions. 3) Earth Model Collaboration, a new web repository for community-supplied regional and global tomography models with the ability to preview, request and compare models. 4) EARS, the EarthScope Automated Receiver Survey, developed at the University of South Carolina, aims to calculate crustal thickness and bulk crustal properties beneath USArray stations as well as many other broadband stations whose data are archived at the IRIS DMC. 5) Archiving and distribution of Princeton 3D SEM and 1D synthetic seismograms generated for all Global CMT events. 6) Archiving and distribution of GPS displacement time series produced by the Plate Boundary Observatory. Other data products are under consideration and will be moved to the development pipeline once approved by the IRIS DPWG. Feedback on existing products and ideas for new products are welcome at any time.

Investigation of the Storage Behavior of Shredded Lithium-Ion Batteries from Electric Vehicles for Recycling Purposes.

PubMed

Grützke, Martin; Krüger, Steffen; Kraft, Vadim; Vortmann, Britta; Rothermel, Sergej; Winter, Martin; Nowak, Sascha

2015-10-26

Shredding of the cells is often the first step in lithium-ion battery (LIB) recycling. Thus, LiNi1/3 Mn1/3 Co1/3 O2 (NMC)/graphite lithium-ion cells from a field-tested electric vehicle were shredded and transferred to tinplate or plastic storage containers. The formation of hazardous compounds within, and being released from, these containers was monitored over 20 months. The tinplate cans underwent fast corrosion as a result of either residual charge in the active battery material, which could not fully be discharged because of contact loss to the current collector, or redox reactions between the tinplate surface and metal parts of the shredded material. The headspace compositions of the containers were investigated at room temperature and 150 °C using headspace-gas chromatography-mass spectrometry (HS-GC-MS). Samples of the waste material were also collected using microwave-assisted extraction and the extracts were analyzed over a period of 20 months using ion chromatography-electrospray ionization-mass spectrometry (IC-ESI-MS). LiPF6 was identified as a conducting salt, whereas dimethyl carbonate, ethyl methyl carbonate, and ethylene carbonate were the main solvent components. Cyclohexylbenzene was also detected, which is an additive for overcharge protection. Diethyl carbonate, fluoride, difluorophosphate and several ionic and non-ionic alkyl (fluoro)phosphates were also identified. Importantly, dimethyl fluorophosphate (DMFP) and diethyl fluorophosphate (DEFP) were quantified using HS-GC-MS through the use of an internal standard. DMFP, DEFP, and related compounds are known as chemical warfare agents, and the presence of these materials is of great interest. In the case of this study, these hazardous materials are present but in manageable low concentrations. Nonetheless, the presence of such compounds and their potential release during an accident that may occur during shredding or recycling of large amounts of LIB waste should be considered. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of dimethyl sulfide on the carbon cycle and biological production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Shanlin; Maltrud, Mathew; Elliott, Scott

Dimethyl sulfide (DMS) is a significant source of marine sulfate aerosol and plays an important role in modifying cloud properties. Fully coupled climate simulations using dynamic marine ecosystem and DMS calculations are conducted to estimate DMS fluxes under various climate scenarios and to examine the sign and strength of phytoplankton-DMS-climate feedbacks for the first time. Simulation results show small differences in the DMS production and emissions between pre-industrial and present climate scenarios, except for some areas in the Southern Ocean. There are clear changes in surface ocean DMS concentrations moving into the future, and they are attributable to changes inmore » phytoplankton production and competition driven by complex spatially varying mechanisms. Comparisons between parallel simulations with and without DMS fluxes into the atmosphere show significant differences in marine ecosystems and physical fields. Without DMS, the missing subsequent aerosol indirect effects on clouds and radiative forcing lead to fewer clouds, more solar radiation, and a much warmer climate. Phaeocystis, a uniquely efficient organosulfur producer with a growth advantage under cooler climate states, can benefit from producing the compound through cooling effects of DMS in the climate system. Our results show a tight coupling between the sulfur and carbon cycles. The ocean carbon uptake declines without DMS emissions to the atmosphere. The analysis indicates a weak positive phytoplankton-DMS-climate feedback at the global scale, with large spatial variations driven by individual autotrophic functional groups and complex mechanisms. The sign and strength of the feedback vary with climate states and phytoplankton groups. This highlights the importance of a dynamic marine ecosystem module and the sulfur cycle mechanism in climate projections.« less

Influence of low-temperature combustion and dimethyl ether-diesel blends on performance, combustion, and emission characteristics of common rail diesel engine: a CFD study.

PubMed

Lamani, Venkatesh Tavareppa; Yadav, Ajay Kumar; Narayanappa, Kumar Gottekere

2017-06-01

Due to presence of more oxygen, absence of carbon-carbon (C-C) bond in chemical structure, and high cetane number of dimethyl ether (DME), pollution from DME operated engine is less compared to diesel engine. Hence, the DME can be a promising alternative fuel for diesel engine. The present study emphasizes the effect of various exhaust gas recirculation (EGR) rates (0-20%) and DME/Diesel blends (0-20%) on combustion characteristics and exhaust emissions of common rail direct injection (CRDI) engine using three-dimensional computational fluid dynamics (CFD) simulation. Extended coherent flame model-3 zone (ECFM-3Z) is implemented to carry out combustion analysis, and k-ξ-f model is employed for turbulence modeling. Results show that in-cylinder pressure marginally decreases with employing EGR compared to without EGR case. As EGR rate increases, nitrogen oxide (NO) formation decreases, whereas soot increases marginally. Due to better combustion characteristics of DME, indicated thermal efficiency (ITE) increases with the increases in DME/diesel blend ratio. Adverse effect of EGR on efficiency for blends is less compared to neat diesel, because the anoxygenated region created due to EGR is compensated by extra oxygen present in DME. The trade-off among NO, soot, carbon monoxide (CO) formation, and efficiency is studied by normalizing the parameters. Optimum operating condition is found at 10% EGR rate and 20% DME/diesel blend. The maximum indicated thermal efficiency was observed for DME/diesel ratio of 20% in the present range of study. Obtained results are validated with published experimental data and found good agreement.

Influence of dimethyl sulfide on the carbon cycle and biological production

DOE PAGES

Wang, Shanlin; Maltrud, Mathew; Elliott, Scott; ...

2018-02-27

Dimethyl sulfide (DMS) is a significant source of marine sulfate aerosol and plays an important role in modifying cloud properties. Fully coupled climate simulations using dynamic marine ecosystem and DMS calculations are conducted to estimate DMS fluxes under various climate scenarios and to examine the sign and strength of phytoplankton-DMS-climate feedbacks for the first time. Simulation results show small differences in the DMS production and emissions between pre-industrial and present climate scenarios, except for some areas in the Southern Ocean. There are clear changes in surface ocean DMS concentrations moving into the future, and they are attributable to changes inmore » phytoplankton production and competition driven by complex spatially varying mechanisms. Comparisons between parallel simulations with and without DMS fluxes into the atmosphere show significant differences in marine ecosystems and physical fields. Without DMS, the missing subsequent aerosol indirect effects on clouds and radiative forcing lead to fewer clouds, more solar radiation, and a much warmer climate. Phaeocystis, a uniquely efficient organosulfur producer with a growth advantage under cooler climate states, can benefit from producing the compound through cooling effects of DMS in the climate system. Our results show a tight coupling between the sulfur and carbon cycles. The ocean carbon uptake declines without DMS emissions to the atmosphere. The analysis indicates a weak positive phytoplankton-DMS-climate feedback at the global scale, with large spatial variations driven by individual autotrophic functional groups and complex mechanisms. The sign and strength of the feedback vary with climate states and phytoplankton groups. This highlights the importance of a dynamic marine ecosystem module and the sulfur cycle mechanism in climate projections.« less

Morphology and chemistry of Dufour glands in four ectoparasitoids: Cephalonomia tarsalis, C. waterstoni (Hymenoptera: Bethylidae), Anisopteromalus calandrae, and Pteromalus cerealellae (Hymenoptera: Pteromalidae).

PubMed

Howard, Ralph W; Baker, James E

2003-05-01

The venom apparatus of four hymenopterous parasitoids, including two bethylids, C. tarsalis (Ashmead) and C. waterstoni (Gahan), and two pteromalids, A. calandrae (Howard) and P. cerealellae (Ashmead), were removed and the associated Dufour glands characterized with respect to their external morphology and chemistry. Dufour glands in all four species have a characteristic translucent appearance that apparently results from their lipid content. The stalked Dufour glands of C. tarsalis and C. waterstoni are pear-shaped and have overall lengths of approximately 0.2 and 0.15 mm, respectively. The thin venom glands are bifurcate and insert through a fine duct into the transparent ovoid- to pear-shaped venom reservoir in these bethylids. In A. calandrae and P. cerealellae the Dufour glands are elongated, tubular structures of ca. 0.35 and 0.8 mm in length, respectively, that constrict to a short stalk that empties into the common oviduct. The venom glands in these pteromalids are simple elongated structures that insert into the sac-like venom reservoir through a fine duct. The chemistry of the volatile contents of the Dufour gland in these four species differs considerably. C. tarsalis Dufour glands contain the same hydrocarbon components as found on the cuticle of this species (Ann. Entomol. Soc. Am. 91:101-112 (1998)), and no other chemicals. The Dufour glands of C. waterstoni also contain only hydrocarbons, most of which are the same as the cuticular hydrocarbons (Ann. Entomol. Soc. Am. 85:317-325 (1992)), but in addition the Dufour gland contains ca. 3% of a mixture of 2,17- and 2,19-dimethyl C(23). A. calandrae Dufour gland chemistry is somewhat more complex than that of either of the two bethylids, but like the bethylids, only hydrocarbons are present. The carbon number range is from C(30) to C(39) and consists of a mixture of n-alkanes (C(30)-C(38)); 3-, 5-, 7-, 9-, 11-, 12-, 13-, 14-, 15- and 17-methyl alkanes; 3,7- and 3,11-dimethyl alkanes; 5,9- and 5,17-dimethyl alkanes; 7,11-, 9,13-, 13,17-, 14,18- and 15,19-dimethyl alkanes; 3,7,11- and 3, 9,15-trimethyl alkanes; and 3,7,11,15-tetramethyl alkanes. The cuticular hydrocarbons of this species have not been previously reported, but they are the same as the Dufour gland hydrocarbons. The Dufour glands of P. cerealellae contain both hydrocarbons and two long-chain aldehydes. Most of the hydrocarbons are identical to those found on the cuticle of this species (Ann. Entomol. Soc. Am. 94:152-158 (2001)), but in addition, 5,9-dimethyl C(27), 5,13-, 5,17- and 5,19-dimethyl C(35), 12- and 14-methyl C(36), 12,16- and 13,17-dimethyl C(36), 13-methyl C(37) and 13,17-dimethyl C(37) are present. The two aldehydes detected in glands from P. cerealellae are n-tetracosanal (C(23)CHO) and n-hexacosanal (C(25)CHO).

Temperature control in a solar collector field using Filtered Dynamic Matrix Control.

PubMed

Lima, Daniel Martins; Normey-Rico, Julio Elias; Santos, Tito Luís Maia

2016-05-01

This paper presents the output temperature control of a solar collector field of a desalinization plant using the Filtered Dynamic Matrix Control (FDMC). The FDMC is a modified controller based on the Dynamic Matrix Control (DMC), a predictive control strategy widely used in industry. In the FDMC, a filter is used in the prediction error, which allows the modification of the robustness and disturbance rejection characteristics of the original algorithm. The implementation and tuning of the FDMC are simple and maintain the advantages of DMC. Several simulation results using a validated model of the solar plant are presented considering different scenarios. The results are also compared to nonlinear control techniques, showing that FDMC, if properly tuned, can yield similar results to more complex control algorithms. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Helical filaments of human Dmc1 protein on single-stranded DNA: a cautionary tale.

PubMed

Yu, Xiong; Egelman, Edward H

2010-08-20

Proteins in the RecA/Rad51/RadA family form nucleoprotein filaments on DNA that catalyze a strand exchange reaction as part of homologous genetic recombination. Because of the centrality of this system to many aspects of DNA repair, the generation of genetic diversity, and cancer when this system fails or is not properly regulated, these filaments have been the object of many biochemical and biophysical studies. A recent paper has argued that the human Dmc1 protein, a meiotic homolog of bacterial RecA and human Rad51, forms filaments on single-stranded DNA with approximately 9 subunits per turn in contrast to the filaments formed on double-stranded DNA with approximately 6.4 subunits per turn and that the stoichiometry of DNA binding is different between these two filaments. We show using scanning transmission electron microscopy that the Dmc1 filament formed on single-stranded DNA has a mass per unit length expected from approximately 6.5 subunits per turn. More generally, we show how ambiguities in helical symmetry determination can generate incorrect solutions and why one sometimes must use other techniques, such as biochemistry, metal shadowing, or scanning transmission electron microscopy, to resolve these ambiguities. While three-dimensional reconstruction of helical filaments from EM images is a powerful tool, the intrinsic ambiguities that may be present with limited resolution are not sufficiently appreciated. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Multi-scale curvature for automated identification of glaciated mountain landscapes

NASA Astrophysics Data System (ADS)

Prasicek, Günther; Otto, Jan-Christoph; Montgomery, David R.; Schrott, Lothar

2014-03-01

Erosion by glacial and fluvial processes shapes mountain landscapes in a long-recognized and characteristic way. Upland valleys incised by fluvial processes typically have a V-shaped cross-section with uniform and moderately steep slopes, whereas glacial valleys tend to have a U-shaped profile with a changing slope gradient. We present a novel regional approach to automatically differentiate between fluvial and glacial mountain landscapes based on the relation of multi-scale curvature and drainage area. Sample catchments are delineated and multiple moving window sizes are used to calculate per-cell curvature over a variety of scales ranging from the vicinity of the flow path at the valley bottom to catchment sections fully including valley sides. Single-scale curvature can take similar values for glaciated and non-glaciated catchments but a comparison of multi-scale curvature leads to different results according to the typical cross-sectional shapes. To adapt these differences for automated classification of mountain landscapes into areas with V- and U-shaped valleys, curvature values are correlated with drainage area and a new and simple morphometric parameter, the Difference of Minimum Curvature (DMC), is developed. At three study sites in the western United States the DMC thresholds determined from catchment analysis are used to automatically identify 5 × 5 km quadrats of glaciated and non-glaciated landscapes and the distinctions are validated by field-based geological and geomorphological maps. Our results demonstrate that DMC is a good predictor of glacial imprint, allowing automated delineation of glacially and fluvially incised mountain landscapes.

A distributed monitoring system for photovoltaic arrays based on a two-level wireless sensor network

NASA Astrophysics Data System (ADS)

Su, F. P.; Chen, Z. C.; Zhou, H. F.; Wu, L. J.; Lin, P. J.; Cheng, S. Y.; Li, Y. F.

2017-11-01

In this paper, a distributed on-line monitoring system based on a two-level wireless sensor network (WSN) is proposed for real time status monitoring of photovoltaic (PV) arrays to support the fine management and maintenance of PV power plants. The system includes the sensing nodes installed on PV modules (PVM), sensing and routing nodes installed on combiner boxes of PV sub-arrays (PVA), a sink node and a data management centre (DMC) running on a host computer. The first level WSN is implemented by the low-cost wireless transceiver nRF24L01, and it is used to achieve single hop communication between the PVM nodes and their corresponding PVA nodes. The second level WSN is realized by the CC2530 based ZigBee network for multi-hop communication among PVA nodes and the sink node. The PVM nodes are used to monitor the PVM working voltage and backplane temperature, and they send the acquired data to their PVA node via the nRF24L01 based first level WSN. The PVA nodes are used to monitor the array voltage, PV string current and environment irradiance, and they send the acquired and received data to the DMC via the ZigBee based second level WSN. The DMC is designed using the MATLAB GUIDE and MySQL database. Laboratory experiment results show that the system can effectively acquire, display, store and manage the operating and environment parameters of PVA in real time.

Thermoplastic polymides and composites therefrom

NASA Technical Reports Server (NTRS)

Harris, Frank W. (Inventor)

1994-01-01

A new class polyimide and polyimide precursors based on diaryl oxyalkylene diamines, such as 1,3-bis[4-aminophenoxy]-2,2-dimethyl propane, a process for their preparation and their use as the continuous phase for the manufacture of composites and composite laminates reinforced by reinforcing agents such as carbon fibers, Kevlar.TM., and other similar high strength reinforcing agents. The polyimides and molecular composites obtained from the diamines according to the invention show thermoplastic properties, excellent flex fatigue and fracture resistance, and excellent thermal and oxidative stability.

Pt and Pd catalyzed oxidation of Li 2O 2 and DMSO during Li–O 2 battery charging

DOE PAGES

Gittleson, Forrest S.; Ryu, Won-Hee; Schwab, Mark; ...

2016-01-01

Rechargeable Li-O 2 and Li-air batteries require electrode and electrolyte materials that synergistcally promote long-term cell operation. We investigate the role of noble metals Pt and Pd as catalysts for the Li-O 2 oxidation process and their compatibility with a dimethyl sulfoxide (DMSO) based electrolyte. Lastly, we identify a basis for low potential Li 2O 2 evolution followed by oxidative decomposition of the electrolyte to form carbonate side products.

Synthesis and characteristics of polyarylene ether sulfones

NASA Technical Reports Server (NTRS)

Viswanathan, R.; Johnson, B. C.; Ward, T. C.; Mcgrath, J. E.

1981-01-01

A method utilizing potassium carbonate/dimethyl acetamide, as base and solvent respectively, was used for the synthesis of several homopolymers and copolymers derived from various bisphenols. It is demonstrated that this method deviates from simple second order kinetics; this deviation being due to the heterogeneous nature of the reaction. Also, it is shown that a liquid induced crystallization process can improve the solvent resistance of these polymers. Finally, a Monte Carlo simulation of the triad distribution of monomers in nonequilibrium copolycondensation is discussed.

Structure-Function Study of Tertiary Amines as Switchable Polarity Solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aaron D. Wilson; Frederick F. Stewart

2014-02-01

A series of tertiary amines have been screened for their function as switchable polarity solvents (SPS). The relative ratios of tertiary amine and carbonate species as well as maximum possible concentration were determined through quantitative 1H and 13C NMR spectroscopy. The viscosities of the polar SPS solutions were measured and ranged from near water in dilute systems through to gel formation at high concentrations. The van't Hoff indices for SPS solutions were measured through freezing point depression studies as a proxy for osmotic pressures. A new form of SPS with an amine : carbonate ratio significantly greater than unity hasmore » been identified. Tertiary amines that function as SPS at ambient pressures appear to be limited to molecules with fewer than 12 carbons. The N,N-dimethyl-n-alkylamine structure has been identified as important to the function of an SPS.« less

Direct synthesis of formic acid from carbon dioxide by hydrogenation in acidic media

PubMed Central

Moret, Séverine; Dyson, Paul J.; Laurenczy, Gábor

2014-01-01

The chemical transformation of carbon dioxide into useful products becomes increasingly important as CO2 levels in the atmosphere continue to rise as a consequence of human activities. In this article we describe the direct hydrogenation of CO2 into formic acid using a homogeneous ruthenium catalyst, in aqueous solution and in dimethyl sulphoxide (DMSO), without any additives. In water, at 40 °C, 0.2 M formic acid can be obtained under 200 bar, however, in DMSO the same catalyst affords 1.9 M formic acid. In both solvents the catalysts can be reused multiple times without a decrease in activity. Worldwide demand for formic acid continues to grow, especially in the context of a renewable energy hydrogen carrier, and its production from CO2 without base, via the direct catalytic carbon dioxide hydrogenation, is considerably more sustainable than the existing routes. PMID:24886955

Direct synthesis of formic acid from carbon dioxide by hydrogenation in acidic media.

PubMed

Moret, Séverine; Dyson, Paul J; Laurenczy, Gábor

2014-06-02

The chemical transformation of carbon dioxide into useful products becomes increasingly important as CO2 levels in the atmosphere continue to rise as a consequence of human activities. In this article we describe the direct hydrogenation of CO2 into formic acid using a homogeneous ruthenium catalyst, in aqueous solution and in dimethyl sulphoxide (DMSO), without any additives. In water, at 40 °C, 0.2 M formic acid can be obtained under 200 bar, however, in DMSO the same catalyst affords 1.9 M formic acid. In both solvents the catalysts can be reused multiple times without a decrease in activity. Worldwide demand for formic acid continues to grow, especially in the context of a renewable energy hydrogen carrier, and its production from CO2 without base, via the direct catalytic carbon dioxide hydrogenation, is considerably more sustainable than the existing routes.

Carbon Dioxide Utilization by the Five-Membered Ring Products of Cyclometalation Reactions

PubMed Central

Omae, Iwao

2016-01-01

In carbon dioxide utilization by cyclometalated five-membered ring products, the following compounds are used in four types of applications: 1. 2-Phenylpyrazole iridium compounds, pincer phosphine iridium compounds and 2-phenylimidazoline iridium compounds are used as catalysts for both formic acid production from CO2 and H2, and hydrogen production from the formic acid. This formic acid can be a useful agent for H2 production and storage for fuel cell electric vehicles. 2. Other chemicals, e.g., dimethyl carbonate, methane, methanol and CO, are produced with dimethylaminomethylphenyltin compounds, pincer phosphine iridium compounds, pincer phosphine nickel compound and ruthenium carbene compound or 2-phenylpyridine iridium compounds, and phenylbenzothiazole iridium compounds as the catalysts for the reactions with CO2. 3. The five-membered ring intermediates of cyclometalation reactions with the conventional substrates react with carbon dioxide to afford their many types of carboxylic acid derivatives. 4. Carbon dioxide is easily immobilized at room temperature with immobilizing agents such as pincer phosphine nickel compounds, pincer phosphine palladium compounds, pincer N,N-dimethylaminomethyltin compounds and tris(2-pyridylthio)methane zinc compounds. PMID:28503084

Carbon Dioxide Utilization by the Five-Membered Ring Products of Cyclometalation Reactions.

PubMed

Omae, Iwao

2016-04-01

In carbon dioxide utilization by cyclometalated five-membered ring products, the following compounds are used in four types of applications: 1. 2-Phenylpyrazole iridium compounds, pincer phosphine iridium compounds and 2-phenylimidazoline iridium compounds are used as catalysts for both formic acid production from CO 2 and H 2 , and hydrogen production from the formic acid. This formic acid can be a useful agent for H 2 production and storage for fuel cell electric vehicles. 2. Other chemicals, e.g. , dimethyl carbonate, methane, methanol and CO, are produced with dimethylaminomethylphenyltin compounds, pincer phosphine iridium compounds, pincer phosphine nickel compound and ruthenium carbene compound or 2-phenylpyridine iridium compounds, and phenylbenzothiazole iridium compounds as the catalysts for the reactions with CO 2 . 3. The five-membered ring intermediates of cyclometalation reactions with the conventional substrates react with carbon dioxide to afford their many types of carboxylic acid derivatives. 4. Carbon dioxide is easily immobilized at room temperature with immobilizing agents such as pincer phosphine nickel compounds, pincer phosphine palladium compounds, pincer N , N -dimethylaminomethyltin compounds and tris(2-pyridylthio)methane zinc compounds.

Enantioseparation of α-Hydroxyallylphosphonates and Phosphonoallylic Carbonate Derivatives on Chiral Stationary Phases Using Sequential UV, Polarimetric, and Refractive Index Detection.

PubMed

Hamper, Bruce C; Mannino, Michael P; Mueller, Melissa E; Harrison, Liam T; Spilling, Christopher D

2016-09-01

Chromatographic separation of the enantiomers of parent compounds dimethyl α-hydroxyallyl phosphonate and 1-(dimethoxyphosphoryl) allyl methyl carbonate was demonstrated by high-performance liquid chromatography (HPLC) using Chiralpak AS-H and ad-H chiral stationary phases (CSP), respectively, using a combination of UV, polarimetric, and refractive index detectors. A comparison was made of the separation efficiency and elution order of enantiomeric α-hydroxyallyl phosphonates and their carbonate derivatives on commercially available polysaccharide AS, ad, OD, IC-3, and Whelk-O 1 CSPs. In general, the α-hydroxyallyl phosphonates were resolved on the AS-H CSP, whereas the carbonate derivatives and were preferentially resolved on the ad-H CSP. The impact of aryl substitution on the resolution of analytes and was evaluated. Thermodynamic parameters determined for enantioselective adsorption hydroxyphosphonates and on the AS-H CSP and carbonate on the ad-H CSP demonstrated enthalpic control for separation of the enantiomers. Chirality 28:656-662, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

A High T(sub g) PMR Polyimide Composites (DMBZ-15)

NASA Technical Reports Server (NTRS)

Chuang, Kathy C.; Bowles, Kenneth J.; Papadopoulos, Demitrios S.; Hardy-Green, DeNise; Mccorkle, Linda

2000-01-01

A high T(sub g) thermosetting PMR-type polyimide, designated as DMBZ-15, was developed by replacing methylene dianline (MDA) in PMR-15 with 2,2'-dimethylbenzidine. Polyimide/carbon fiber (T650-35) composites were fabricated from a formulation of 3,3', 4,4'-benzophenonetetracarboxylic acid dimethyl ester (BTDE) and 2,2'-dimethylbenzidine (DMBZ), along with nadic ester (NE) as the endcap. DMBZ-15 displays a higher glass transition temperature (T(sub g) = 414 C) than PMR-15 (T(sub g) = 345 C), and thus retains better mechanical properties for brief exposure above 400 C. The physical properties and longterm thermo-oxidative stability of the DMBZ-15 polyimide/carbon fiber composites are also compared to that of PMR-15.

Data Management Coordinators (DMC)

EPA Pesticide Factsheets

The Regional Data Management Coordinators (DMCs) were identified to serve as the primary contact for each region for all Water Quality Framework activities. They will facilitate and communicate information to the necessary individuals at the region and tra

Conversion of sulfur compounds and microbial community in anaerobic treatment of fish and pork waste.

PubMed

He, Ruo; Yao, Xing-Zhi; Chen, Min; Ma, Ruo-Chan; Li, Hua-Jun; Wang, Chen; Ding, Shen-Hua

2018-06-01

Volatile sulfur compounds (VSCs) are not only the main source of malodor in anaerobic treatment of organic waste, but also pose a threat to human health. In this study, VSCs production and microbial community was investigated during the anaerobic degradation of fish and pork waste. The results showed that after the operation of 245 days, 94.5% and 76.2% of sulfur compounds in the fish and pork waste was converted into VSCs. Among the detected VSCs including H 2 S, carbon disulfide, methanethiol, ethanethiol, dimethyl sulfide, dimethyl disulfide and dimethyl trisulfide, methanethiol was the major component with the maximum concentration of 4.54% and 3.28% in the fish and pork waste, respectively. The conversion of sulfur compounds including total sulfur, SO 4 2- -S, S 2- , methionine and cysteine followed the first-order kinetics. Miseq sequencing analysis showed that Acinetobacter, Clostridium, Proteus, Thiobacillus, Hyphomicrobium and Pseudomonas were the main known sulfur-metabolizing microorganisms in the fish and pork waste. The C/N value had most significant influence on the microbial community in the fish and pork waste. A main conversion of sulfur compounds with CH 3 SH as the key intermediate was firstly hypothesized during the anaerobic degradation of fish and pork waste. These findings are helpful to understand the conversion of sulfur compounds and to develop techniques to control ordor pollution in the anaerobic treatment of organic waste. Copyright © 2018 Elsevier Ltd. All rights reserved.

Impact of sea-ice melt on dimethyl sulfide (sulfoniopropionate) inventories in surface waters of Marguerite Bay, West Antarctic Peninsula.

PubMed

Stefels, Jacqueline; van Leeuwe, Maria A; Jones, Elizabeth M; Meredith, Michael P; Venables, Hugh J; Webb, Alison L; Henley, Sian F

2018-06-28

The Southern Ocean is a hotspot of the climate-relevant organic sulfur compound dimethyl sulfide (DMS). Spatial and temporal variability in DMS concentration is higher than in any other oceanic region, especially in the marginal ice zone. During a one-week expedition across the continental shelf of the West Antarctic Peninsula (WAP), from the shelf break into Marguerite Bay, in January 2015, spatial heterogeneity of DMS and its precursor dimethyl sulfoniopropionate (DMSP) was studied and linked with environmental conditions, including sea-ice melt events. Concentrations of sulfur compounds, particulate organic carbon (POC) and chlorophyll a in the surface waters varied by a factor of 5-6 over the entire transect. DMS and DMSP concentrations were an order of magnitude higher than currently inferred in climatologies for the WAP region. Particulate DMSP concentrations were correlated most strongly with POC and the abundance of haptophyte algae within the phytoplankton community, which, in turn, was linked with sea-ice melt. The strong sea-ice signal in the distribution of DMS(P) implies that DMS(P) production is likely to decrease with ongoing reductions in sea-ice cover along the WAP. This has implications for feedback processes on the region's climate system.This article is part of the theme issue 'The marine system of the West Antarctic Peninsula: status and strategy for progress in a region of rapid change'. © 2018 The Author(s).

Naturally-Occurring DMSP Analogs as Potential Precursors of Dimethyl Sulfide (DMS) and Methanethiol (MeSH) in Coastal Seawater

NASA Astrophysics Data System (ADS)

Cordero, D.; Kiene, R. P.

2016-02-01

Dimethylsulfoniopropionate (DMSP) is an osmolyte produced by various macroalgae and phytoplankton in the marine environment. DMSP is known to be the main precursor for dimethyl sulfide (DMS), the major natural sulfur gas emitted from the oceans to the atmosphere. DMS contributes to formation and growth of sulfur-containing aerosols in our stratosphere. These aerosols influence Earth's solar radiation balance and potentially affect the formation of clouds, which could function as a counter-effect to global warming. Bacterioplankton are capable of converting DMSP into DMS via the enzyme DMSP lyase. But not all DMSP in the ocean is converted into DMS. A significant fraction of the DMSP available in the ocean is converted to methanethiol (MeSH) via the bacterial demethylation/demethiolation pathway, with a portion of the MeSH being assimilated as both a carbon and sulfur source. Here we test whether several other naturally-occurring dimethyl sulfonium compounds could be precursors of DMS and MeSH. To test this, we carried out experiments with estuarine water samples from Mobile Bay in the Northern Gulf of Mexico. After collection, unfiltered seawater and seawater filtrate samples, the later containing bacteria only, were treated with 50 nM additions of either 2-dimethylsulfononioacetate (DMSA) or S-Methylmethionine (SMM). After addition of the dimethyl sulfonium compounds, samples were analyzed for sulfur gases with Gas Chromatography-Flame Photometric Detection, using cryogenic-trapping techniques. Addition of DMSA resulted in an immediate increase in MeSH production in both seawater and seawater filtrate containing bacteria only, producing even more MeSH than DMSP. This suggests that DMSA is potentially a significant precursor for MeSH. DMS was not produced in significant amounts from DMSA. Addition of SMM resulted in low rates of both DMS and MeSH accumulation in both seawater samples, indicating that SMM may be a minor precursor for both gases compared to DMSP.

Real-time operation of the NSF EarthScope USArray Transportable Array

NASA Astrophysics Data System (ADS)

Astiz, L.; Eakins, J. A.; Vernon, F. L.; Martynov, V.; Newman, R. L.; Cox, T. A.; Mulder, T. L.; Busby, R. W.

2007-05-01

The Transportable Array (TA) component of USArray uses real-time telemetry to send data to the Array Network Facility (ANF) through a variety of satellite, mobile phone, wireless and wired communication links. The ANF is responsible for the timely delivery of metadata and waveform data to the IRIS DMC from the growing number of Transportable Array stations. The IRIS DMC makes these data available to the research community. The network has increased in size to 327 stations with 259 out of the 400 new TA sites installed (as of 28 February 2007). Starting in Fall 2007, equipment will start to roll from current stations to new locations to the east of the current footprint. Use of the Antelope software package has allowed the ANF to maintain and operate this extremely dynamic network configuration, facilitating the collection and transfer of data, the generation and merging of the metadata as well as the real-time monitoring of state of health of TA station data-loggers and their command and control. Four regional networks (ANZA, BDSN, SCSN, and UNR) as well as the USNSN contribute data to the Transportable Array in real-time. Although the real-time data flow to the IRIS DMC has been 93.4% over the last year, the ANF and the TA field teams have extended every effort and have managed to recover an additional 4.8% by recovering data from the local data storage device (Baler 14) at each station. Once the missing data is recovered, we then generate station-channel-day volume seed files, which are resent to the DMC to bring the total data recovery rate to 98.4%. The total network uptime is above 99%. Analyst review of automatic locations for the USArray network is being done at the ANF as part of the data quality monitoring strategy. All events are associated with the USGS and regional network bulletins. As of February 2007, around 13,000 weekly picks are being fully reviewed by analysts at the ANF and over 19,000 events have been recorded. We find a small percentage (about 10 %) of events that cannot be associated with existing bulletins. This information is used by the regional network operators to help them determine which TA stations may be beneficial to permanently add to their seismic networks. Operation of the USArray at the ANF has benefited by the real-time interface with the ORB and the Datascope database using PHP for display on the ANF website (http:anf.ucsd.edu) to provide station and system state-of- health information to field teams. Information available for all stations includes: location, maps, photographs, equipment deployed, communications, distribution of events recorded by each station, and displays of daily, weekly, and yearly state of health parameters as well as station noise spectra generated by the DMC.

Catalytic oxidation of gaseous reduced sulfur compounds using coal fly ash.

PubMed

Kastner, James R; Das, K C; Melear, Nathan D

2002-11-11

Activated carbon has been shown to oxidize reduced sulfur compounds, but in many cases it is too costly for large-scale environmental remediation applications. Alternatively, we theorized that coal fly ash, given its high metal content and the presence of carbon could act as an inexpensive catalytic oxidizer of reduced sulfur compounds for "odor" removal. Initial results indicate that coal fly ash can catalyze the oxidization of H(2)S and ethanethiol, but not dimethyl sulfide (DMS) and dimethyl disulfide (DMDS) at room temperature. In batch reactor systems, initial concentrations of 100-500 ppmv H(2)S or ethanethiol were reduced to 0-2 ppmv within 1-2 and 6-8 min, respectively. This was contrary to control systems without ash in which concentrations remained constant. Diethyl disulfide was formed from ethanethiol substantiating the claim that catalytic oxidation occurred. The presence of water increased the rate of adsorption/reaction of both H(2)S and ethanethiol for the room temperature reactions (23-25 degrees C). Additionally, in a continuous flow packed bed reactor, a gaseous stream containing an inlet H(2)S concentration of 400-500 ppmv was reduced to 200 ppmv at a 4.6s residence time. The removal efficiency remained at 50% for approximately 4.6h or 3500 reactor volumes. These results demonstrate the potential of using coal fly ash in reactors for removal of H(2)S and other reduced sulfur compounds.

Generation and detection of metal ions and volatile organic compounds (VOCs) emissions from the pretreatment processes for recycling spent lithium-ion batteries.

PubMed

Li, Jia; Wang, Guangxu; Xu, Zhenming

2016-06-01

The recycling of spent lithium-ion batteries brings benefits to both economic and environmental terms, but it can also lead to contaminants in a workshop environment. This study focused on metals, non-metals and volatile organic compounds generated by the discharging and dismantling pretreatment processes which are prerequisite for recycling spent lithium-ion batteries. After discharging in NaCl solution, metal contents in supernate and concentrated liquor were detected. Among results of condition #2, #3, #4 and #5, supernate and concentrated liquor contain high levels of Na, Al, Fe; middle levels of Co, Li, Cu, Ca, Zn; and low levels of Mn, Sn, Cr, Zn, Ba, K, Mg, V. The Hg, Ag, Cr and V are not detected in any of the analyzed supernate. 10wt% NaCl solution was a better discharging condition for high discharge efficiency, less possible harm to environment. To collect the gas released from dismantled LIB belts, a set of gas collecting system devices was designed independently. Two predominant organic vapour compounds were dimethyl carbonate (4.298mgh(-1)) and tert-amylbenzene (0.749mgh(-1)) from one dismantled battery cell. To make sure the concentrations of dimethyl carbonate under recommended industrial exposure limit (REL) of 100mgL(-1), for a workshop on dismantling capacity of 1000kg spent LIBs, the minimum flow rate of ventilating pump should be 235.16m(3)h(-1). Copyright © 2016 Elsevier Ltd. All rights reserved.

Detection of rare species of volatile organic selenium metabolites in male golden hamster urine.

PubMed

Kwak, Jae; Ohrnberger, Sarah A; Valencak, Teresa G

2016-07-01

Selenium has been considered as an essential trace element in mammals and its intake comes mainly from food. Mammals can metabolize both inorganic and organic species, and urinary excretion is the primary elimination route of selenium. Selenosugars and trimethylselenonium ion have been identified as major urinary metabolites. Other metabolites have been reported, but they were detected in some studies and not in others. Still, a large portion of the ingested selenium eliminated from the body is unknown. Volatile selenium species may account for a certain portion of the unknown species since they can easily be lost during sample analyses. While we analyzed male golden hamster urine in search of potential volatile pheromone(s), four volatile selenium compounds were detected. They were dimethyl selenenylsulfide, dimethyl diselenide, dimethyl bis(thio)selenide, and dimethyl selenodisulfide. When the urine samples were aged and dried for 48 h, dimethyl selenodisulfide tended to increase, while others decreased. The increase might be due to the formation of dimethyl selenodisulfide via reaction of dimethyl diselenide and dimethyl trisulfide whose concentration increased as urine aged. To our knowledge, dimethyl bis(thio)selenide and dimethyl selenodisulfide have never been demonstrated in urine. It remains to be determined whether these species are common metabolites in other animals or hamster-specific.

Binding energies from diffusion Monte Carlo for the MB-pol H{sub 2}O and D{sub 2}O dimer: A comparison to experimental values

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mallory, Joel D.; Mandelshtam, Vladimir A.

2015-10-14

The diffusion Monte Carlo (DMC) method is applied to compute the ground state energies of the water monomer and dimer and their D{sub 2}O isotopomers using MB-pol; the most recent and most accurate ab inito-based potential energy surface (PES). MB-pol has already demonstrated excellent agreement with high level electronic structure data, as well as agreement with some experimental, spectroscopic, and thermodynamic data. Here, the DMC binding energies of (H{sub 2}O){sub 2} and (D{sub 2}O){sub 2} agree with the corresponding values obtained from velocity map imaging within, respectively, 0.01 and 0.02 kcal/mol. This work adds two more valuable data points thatmore » highlight the accuracy of the MB-pol PES.« less

Quantum Monte Carlo calculations of NiO

NASA Astrophysics Data System (ADS)

Maezono, Ryo; Towler, Mike D.; Needs, Richard. J.

2008-03-01

We describe variational and diffusion quantum Monte Carlo (VMC and DMC) calculations [1] of NiO using a 1024-electron simulation cell. We have used a smooth, norm-conserving, Dirac-Fock pseudopotential [2] in our work. Our trial wave functions were of Slater-Jastrow form, containing orbitals generated in Gaussian-basis UHF periodic calculations. Jastrow factor is optimized using variance minimization with optimized cutoff lengths using the same scheme as our previous work. [4] We apply the lattice regulated scheme [5] to evaluate non-local pseudopotentials in DMC and find the scheme improves the smoothness of the energy-volume curve. [1] CASINO ver.2.1 User Manual, University of Cambridge (2007). [2] J.R. Trail et.al., J. Chem. Phys. 122, 014112 (2005). [3] CRYSTAL98 User's Manual, University of Torino (1998). [4] Ryo Maezono et.al., Phys. Rev. Lett., 98, 025701 (2007). [5] Michele Casula, Phys. Rev. B 74, 161102R (2006).

Accurate dipole moment curve and non-adiabatic effects on the high resolution spectroscopic properties of the LiH molecule

NASA Astrophysics Data System (ADS)

Diniz, Leonardo G.; Kirnosov, Nikita; Alijah, Alexander; Mohallem, José R.; Adamowicz, Ludwik

2016-04-01

A very accurate dipole moment curve (DMC) for the ground X1Σ+ electronic state of the 7LiH molecule is reported. It is calculated with the use of all-particle explicitly correlated Gaussian functions with shifted centers. The DMC - the most accurate to our knowledge - and the corresponding highly accurate potential energy curve are used to calculate the transition energies, the transition dipole moments, and the Einstein coefficients for the rovibrational transitions with ΔJ = - 1 and Δv ⩽ 5 . The importance of the non-adiabatic effects in determining these properties is evaluated using the model of a vibrational R-dependent effective reduced mass in the rovibrational calculations introduced earlier (Diniz et al., 2015). The results of the present calculations are used to assess the quality of the two complete linelists of 7LiH available in the literature.

Overview of a Preliminary Destination Mission Concept for a Human Orbital Mission to the Martial Moons

NASA Technical Reports Server (NTRS)

Mazanek, D. D.; Abell, P. A.; Antol, J.; Barbee, B. W.; Beaty, D. W.; Bass, D. S.; Castillo-Rogez, J. C.; Coan, D. A.; Colaprete, A.; Daugherty, K. J.;

Inducing Proactive Control Shifts in the AX-CPT

PubMed Central

Gonthier, Corentin; Macnamara, Brooke N.; Chow, Michael; Conway, Andrew R. A.; Braver, Todd S.

2016-01-01

The Dual Mechanisms of Control (DMC) account (Braver, 2012) proposes two distinct mechanisms of cognitive control, proactive and reactive. This account has been supported by a large number of studies using the AX-CPT paradigm that have demonstrated not only between-group differences, but also within-subjects variability in the use of the two control mechanisms. Yet there has been little investigation of task manipulations that can experimentally modulate the use of proactive control in healthy young adults; such manipulations could be useful to better understand the workings of cognitive control mechanisms. In the current study, a series of three experiments demonstrate how individuals can be systematically biased toward and away from the utilization of proactive control, via strategy training and no-go manipulations, respectively. These results provide increased support for the DMC framework, and provide a new basis from which to examine group-based differences and neural mechanisms underlying the two control modes. PMID:27920741

Extended Thomas-Fermi density functional for the unitary Fermi gas

NASA Astrophysics Data System (ADS)

Salasnich, Luca; Toigo, Flavio

2008-11-01

We determine the energy density ξ(3/5)nɛF and the gradient correction λℏ2(∇n)2/(8mn) of the extended Thomas-Fermi (ETF) density functional, where n is the number density and ɛF is the Fermi energy, for a trapped two-component Fermi gas with infinite scattering length (unitary Fermi gas) on the basis of recent diffusion Monte Carlo (DMC) calculations [Phys. Rev. Lett. 99, 233201 (2007)]. In particular we find that ξ=0.455 and λ=0.13 give the best fit of the DMC data with an even number N of particles. We also study the odd-even splitting γN1/9ℏω of the ground-state energy for the unitary gas in a harmonic trap of frequency ω determining the constant γ . Finally we investigate the effect of the gradient term in the time-dependent ETF model by introducing generalized Galilei-invariant hydrodynamics equations.

Effectiveness of Culturally Appropriate Adaptations to Juvenile Justice Services

PubMed Central

Vergara, Andrew T.; Kathuria, Parul; Woodmass, Kyler; Janke, Robert; Wells, Susan J.

2017-01-01

Despite efforts to increase cultural competence of services within juvenile justice systems, disproportional minority contact (DMC) persists throughout Canada and the United States. Commonly cited approaches to decreasing DMC include large-scale systemic changes as well as enhancement of the cultural relevance and responsiveness of services delivered. Cultural adaptations to service delivery focus on prevention, decision-making, and treatment services to reduce initial contact, minimize unnecessary restraint, and reduce recidivism. Though locating rigorous testing of these approaches compared to standard interventions is difficult, this paper identifies and reports on such research. The Cochrane guidelines for systematic literature reviews and meta-analyses served as a foundation for study methodology. Databases such as Legal Periodicals and Books were searched through June 2015. Three studies were sufficiently rigorous to identify the effect of the cultural adaptations, and three studies that are making potentially important contributions to the field were also reviewed. PMID:29468092

Full Wave Function Optimization with Quantum Monte Carlo and Its Effect on the Dissociation Energy of FeS.

PubMed

Haghighi Mood, Kaveh; Lüchow, Arne

2017-08-17

Diffusion quantum Monte Carlo calculations with partial and full optimization of the guide function are carried out for the dissociation of the FeS molecule. For the first time, quantum Monte Carlo orbital optimization for transition metal compounds is performed. It is demonstrated that energy optimization of the orbitals of a complete active space wave function in the presence of a Jastrow correlation function is required to obtain agreement with the experimental dissociation energy. Furthermore, it is shown that orbital optimization leads to a 5 Δ ground state, in agreement with experiments but in disagreement with other high-level ab initio wave function calculations which all predict a 5 Σ + ground state. The role of the Jastrow factor in DMC calculations with pseudopotentials is investigated. The results suggest that a large Jastrow factor may improve the DMC accuracy substantially at small additional cost.

A Computational Scheme To Evaluate Hamaker Constants of Molecules with Practical Size and Anisotropy.

PubMed

Hongo, Kenta; Maezono, Ryo

2017-11-14

We propose a computational scheme to evaluate Hamaker constants, A, of molecules with practical sizes and anisotropies. Upon the increasing feasibility of diffusion Monte Carlo (DMC) methods to evaluate binding curves for such molecules to extract the constants, we discussed how to treat the averaging over anisotropy and how to correct the bias due to the nonadditivity. We have developed a computational procedure for dealing with the anisotropy and reducing statistical errors and biases in DMC evaluations, based on possible validations on predicted A. We applied the scheme to cyclohexasilane molecule, Si 6 H 12 , used in "printed electronics" fabrications, getting A ≈ 105 ± 2 zJ, being in plausible range supported even by other possible extrapolations. The scheme provided here would open a way to use handy ab initio evaluations to predict wettabilities as in the form of materials informatics over broader molecules.

Diaphragmatic lymphatic vessel behavior during local skeletal muscle contraction.

PubMed

Moriondo, Andrea; Solari, Eleonora; Marcozzi, Cristiana; Negrini, Daniela

2015-02-01

The mechanism through which the stresses developed in the diaphragmatic tissue during skeletal muscle contraction sustain local lymphatic function was studied in 10 deeply anesthetized, tracheotomized adult Wistar rats whose diaphragm was exposed after thoracotomy. To evaluate the direct effect of skeletal muscle contraction on the hydraulic intraluminal lymphatic pressures (Plymph) and lymphatic vessel geometry, the maximal contraction of diaphragmatic fibers adjacent to a lymphatic vessel was elicited by injection of 9.2 nl of 1 M KCl solution among diaphragmatic fibers while Plymph was recorded through micropuncture and vessel geometry via stereomicroscopy video recording. In lymphatics oriented perpendicularly to the longitudinal axis of muscle fibers and located at <300 μm from KCl injection, vessel diameter at maximal skeletal muscle contraction (Dmc) decreased to 61.3 ± 1.4% of the precontraction value [resting diameter (Drest)]; however, if injection was at >900 μm from the vessel, Dmc enlarged to 131.1 ± 2.3% of Drest. In vessels parallel to muscle fibers, Dmc increased to 122.8 ± 2.9% of Drest. During contraction, Plymph decreased as much as 22.5 ± 2.6 cmH2O in all submesothelial superficial vessels, whereas it increased by 10.7 ± 5.1 cmH2O in deeper vessels running perpendicular to contracting muscle fibers. Hence, the three-dimensional arrangement of the diaphragmatic lymphatic network seems to be finalized to efficiently exploit the stresses exerted by muscle fibers during the contracting inspiratory phase to promote lymph formation in superficial submesothelial lymphatics and its further propulsion in deeper intramuscular vessels. Copyright © 2015 the American Physiological Society.

Multi-scale curvature for automated identification of glaciated mountain landscapes☆

PubMed Central

Prasicek, Günther; Otto, Jan-Christoph; Montgomery, David R.; Schrott, Lothar

2014-01-01

Erosion by glacial and fluvial processes shapes mountain landscapes in a long-recognized and characteristic way. Upland valleys incised by fluvial processes typically have a V-shaped cross-section with uniform and moderately steep slopes, whereas glacial valleys tend to have a U-shaped profile with a changing slope gradient. We present a novel regional approach to automatically differentiate between fluvial and glacial mountain landscapes based on the relation of multi-scale curvature and drainage area. Sample catchments are delineated and multiple moving window sizes are used to calculate per-cell curvature over a variety of scales ranging from the vicinity of the flow path at the valley bottom to catchment sections fully including valley sides. Single-scale curvature can take similar values for glaciated and non-glaciated catchments but a comparison of multi-scale curvature leads to different results according to the typical cross-sectional shapes. To adapt these differences for automated classification of mountain landscapes into areas with V- and U-shaped valleys, curvature values are correlated with drainage area and a new and simple morphometric parameter, the Difference of Minimum Curvature (DMC), is developed. At three study sites in the western United States the DMC thresholds determined from catchment analysis are used to automatically identify 5 × 5 km quadrats of glaciated and non-glaciated landscapes and the distinctions are validated by field-based geological and geomorphological maps. Our results demonstrate that DMC is a good predictor of glacial imprint, allowing automated delineation of glacially and fluvially incised mountain landscapes. PMID:24748703

High-activity PtRuPd/C catalyst for direct dimethyl ether fuel cells.

PubMed

Li, Qing; Wen, Xiaodong; Wu, Gang; Chung, Hoon T; Gao, Rui; Zelenay, Piotr

2015-06-22

Dimethyl ether (DME) has been considered as a promising alternative fuel for direct-feed fuel cells but lack of an efficient DME oxidation electrocatalyst has remained the challenge for the commercialization of the direct DME fuel cell. The commonly studied binary PtRu catalyst shows much lower activity in DME than methanol oxidation. In this work, guided by density functional theory (DFT) calculation, a ternary carbon-supported PtRuPd catalyst was designed and synthesized for DME electrooxidation. DFT calculations indicated that Pd in the ternary PtRuPd catalyst is capable of significantly decreasing the activation energy of the CO and CH bond scission during the oxidation process. As evidenced by both electrochemical measurements in an aqueous electrolyte and polymer-electrolyte fuel cell testing, the ternary catalyst shows much higher activity (two-fold enhancement at 0.5 V in fuel cells) than the state-of-the-art binary Pt50 Ru50 /C catalyst (HiSPEC 12100). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

On the temperature dependence of flammability limits of gases.

PubMed

Kondo, Shigeo; Takizawa, Kenji; Takahashi, Akifumi; Tokuhashi, Kazuaki

2011-03-15

Flammability limits of several combustible gases were measured at temperatures from 5 to 100 °C in a 12-l spherical flask basically following ASHRAE method. The measurements were done for methane, propane, isobutane, ethylene, propylene, dimethyl ether, methyl formate, 1,1-difluoroethane, ammonia, and carbon monoxide. As the temperature rises, the lower flammability limits are gradually shifted down and the upper limits are shifted up. Both the limits shift almost linearly to temperature within the range examined. The linear temperature dependence of the lower flammability limits is explained well using a limiting flame temperature concept at the lower concentration limit (LFL)--'White's rule'. The geometric mean of the flammability limits has been found to be relatively constant for many compounds over the temperature range studied (5-100 °C). Based on this fact, the temperature dependence of the upper flammability limit (UFL) can be predicted reasonably using the temperature coefficient calculated for the LFL. However, some compounds such as ethylene and dimethyl ether, in particular, have a more complex temperature dependence. Copyright © 2011 Elsevier B.V. All rights reserved.

Study on systems based on coal and natural gas for producing dimethyl ether

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, L.; Hu, S.Y.; Chen, D.J.

2009-04-15

China is a coal-dependent country and will remain so for a long time. Dimethyl ether (DME), a potential substitute for liquid fuel, is a kind of clean diesel motor fuel. The production of DME from coal is meaningful and is studied in this article. Considering the C/H ratios of coal and natural gas (NG), the cofeed (coal and NG) system (CFS), which does not contain the water gas shift process, is studied. It can reduce CO{sub 2} emission and increase the conversion rate of carbon, producing more DME. The CFS is simulated and compared with the coal-based and NG-based systemsmore » with different recycling ratios. The part of the exhaust gas that is not recycled is burned, producing electricity. On the basis of the simulation results, the thermal efficiency, economic index, and CO{sub 2} emission ratio are calculated separately. The CFS with a 100% recycling ratio has the best comprehensive evaluation index, while the energy, economy, and environment were considered at the same time.« less

Fabrication of two-layer poly(dimethyl siloxane) devices for hydrodynamic cell trapping and exocytosis measurement with integrated indium tin oxide microelectrodes arrays

PubMed Central

Gao, Changlu; Sun, Xiuhua; Gillis, Kevin D.

2016-01-01

The design, fabrication and test of a microfluidic cell trapping device to measure single cell exocytosis were reported. Research on the patterning of double layer template based on repetitive standard photolithography of AZ photoresist was investigated. The replicated poly(dimethyl siloxane) devices with 2.5 μm deep channels were proved to be efficient for stopping cells. Quantal exocytosis measurement can be achieved by targeting single or small clumps of chromaffin cells on top of the 10 μm ×10 μm indium tin oxide microelectrodes arrays with the developed microdevice. And about 72% of the trapping sites can be occupied by cells with hydrodynamic trapping method and the recorded amperometric signals are comparable to the results with traditional carbon fiber microelectrodes. The method of manufacturing the microdevices is simple, low-cost and easy to perform. The manufactured device offers a platform for the high throughput detection of quantal catecholamine exocytosis from chromaffin cells with sufficient sensitivity and broad application. PMID:23329291

Surface Nanobubbles in Nonaqueous Media: Looking for Nanobubbles in DMSO, Formamide, Propylene Carbonate, Ethylammonium Nitrate, and Propylammonium Nitrate.

PubMed

An, Hongjie; Liu, Guangming; Atkin, Rob; Craig, Vincent S J

2015-07-28

Surface nanobubbles produced by supersaturation during the exchange of ethanol for water are routinely observed on hydrophobic surfaces, are stable for days, and have contact angles that are very much greater than observed macroscopically. Here, we test the hypothesis that nanobubbles can also be observed in nonaqueous solvents in order to ascertain if their anomalous lifetimes and contact angles are related to properties of the solvent. Nanobubbles were seen in the protic solvents formamide, ethylammonium nitrate, and propylammonium nitrate, but not in propylene carbonate or dimethyl sulfoxide. Solvents in which nanobubbles were observed exhibit a three-dimensional hydrogen-bonding network. Like in aqueous systems, the nanobubbles were stable for days and exhibited high contact angles (∼165°).

A novel five-lipoxygenase activity protein inhibitor labeled with carbon-14 and deuterium.

PubMed

Latli, Bachir; Hrapchak, Matt; Gao, Joe J; Busacca, Carl A; Senanayake, Chris H

2015-07-01

2-[4-(3-{(1R)-1-[4-(2-Aminopyrimidin-5-yl)phenyl]-1-cyclopropylethyl}-1,2,4-oxadiazol-5-yl)-1H-pyrazol-1-yl]-N,N-dimethylacetamide (1), is a novel and selective five-lipoxygenase activity protein (FLAP) inhibitor with excellent pharmacokinetics properties. The availability of a key chiral intermediate allowed the synthesis of [(14) C]-(1) in six radiochemical steps and in 47% overall radiochemical yield with a specific activity of 51 mCi/mmol using carbon-14 zinc cyanide. 2-Chloro-N,N-dimethyl-(2)H6-acetamide was prepared and condensed with a penultimate intermediate to give [(2)H6]-(1) in very high yield and in more than 99% isotopic enrichment. Copyright © 2015 John Wiley & Sons, Ltd.

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10666 - Quaternary ammonium compounds, bis(fattyalkyl) dimethyl, salts with tannins (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

...(fattyalkyl) dimethyl, salts with tannins (generic). 721.10666 Section 721.10666 Protection of Environment..., bis(fattyalkyl) dimethyl, salts with tannins (generic). (a) Chemical substance and significant new... compounds, bis(fattyalkyl) dimethyl, salts with tannins (PMN P-12-437) is subject to reporting under this...

40 CFR 721.10666 - Quaternary ammonium compounds, bis(fattyalkyl) dimethyl, salts with tannins (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

...(fattyalkyl) dimethyl, salts with tannins (generic). 721.10666 Section 721.10666 Protection of Environment..., bis(fattyalkyl) dimethyl, salts with tannins (generic). (a) Chemical substance and significant new... compounds, bis(fattyalkyl) dimethyl, salts with tannins (PMN P-12-437) is subject to reporting under this...

40 CFR 721.10352 - Dimethyl terephthalate, polymer with alkyl diol and substituted benzoates (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Dimethyl terephthalate, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10352 Dimethyl terephthalate, polymer... subject to reporting. (1) The chemical substance identified generically as dimethyl terephthalate, polymer...

40 CFR 721.10352 - Dimethyl terephthalate, polymer with alkyl diol and substituted benzoates (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Dimethyl terephthalate, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10352 Dimethyl terephthalate, polymer... subject to reporting. (1) The chemical substance identified generically as dimethyl terephthalate, polymer...

40 CFR 721.10352 - Dimethyl terephthalate, polymer with alkyl diol and substituted benzoates (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Dimethyl terephthalate, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10352 Dimethyl terephthalate, polymer... subject to reporting. (1) The chemical substance identified generically as dimethyl terephthalate, polymer...

40 CFR 721.6167 - Piperdinium, 1,1-dimethyl-, chloride.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Piperdinium, 1,1-dimethyl-, chloride... Substances § 721.6167 Piperdinium, 1,1-dimethyl-, chloride. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as piperdinium, 1,1-dimethyl-, chloride. (PMN...

21 CFR 172.824 - Sodium mono- and dimethyl naphthalene sulfonates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium mono- and dimethyl naphthalene sulfonates... sulfonates. The food additive sodium mono- and dimethyl naphthalene sulfonates may be safely used in... statement declaring the presence of sodium mono- and dimethyl naphthalene sulfonates. [42 FR 14491, Mar. 15...

Synthesis and evaluation of borates derived from boric acid and diols for the protection of wood against fungal decay and thermal degradation

Treesearch

George C. Chen

2004-01-01

N,N-dimethyl amino carbinol catechol borate(1). N,N-dimethyl amino carbinol-4-methyl catechol borate(2), N,N-dimethyl amino carbinol-4-t- butyl catechol borate(3). N,N-dimethyl amino carbinol-2,3-naphthyl borate 4) were synthesized by refluxing boric acid and diol in DMF(N,N-dimethyl formamide). The borates were characterized by NMR. Wood impregnated with borate 1,2 or...

The vibrational spectra and structures of dimethyl oxaloacetate and dimethyl oxaloacetate- d2

NASA Astrophysics Data System (ADS)

Schiering, David W.; Katon, J. E.

The complete vibrational spectra of dimethyl oxaloacetate and dimethyl oxaloacetate- d2 have been recorded and analyzed. The i.r. spectra were recorded at liquid N 2 as well as ambient temperature. Tentative vibrational assignments are proposed based on an enol structure in the crystalline phase. In solution, dimethyl oxaloacetate exists as a tautomeric mixture of keto and enol forms. Evidence for the existence of different enol conformers in CCl 4 and CS 2 solutions is also presented.

Reaction of carbon dioxide with a palladium–alkyl complex supported by a bis–NHC framework†

PubMed Central

Ariyananda, Piyal W. G.; Yap, Glenn P. A.

2012-01-01

The reactivity of a dimethyl palladium complex supported by a dicarbene chelate (MDCMes)PdMe2 towards CO2 has been investigated. In the presence of trace H2O, this reaction yields the corresponding methyl bicarbonate complex (MDCMes)PdMe(O2COH), which goes on to give the corresponding κ2-carbonato complex upon crystallization (MDCMes)Pd(CO3). This chemistry, as well as related protonolysis by acetic acid was monitored by a combination of techniques including React-IR spectroscopy. PMID:22643651

1-[(3,5-Dimethyl-1H-pyrazol-1-yl)carbon­yl]-5-methyl­indolizine-3-carbo­nitrile

PubMed Central

Gu, Wei-Jin; Xie, Wen-Li; Wang, Ting-Ting

2012-01-01

In the title mol­ecule, C16H14N4O, the indolizine ring system is essentially planar, with a maximum deviation of 0.013 (3) Å, and forms a dihedral angle of 7.52 (12)° with the pyrazole ring. In the crystal, weak C—H⋯O hydrogen bonds and π–π stacking inter­actions, with a centroid–centroid distance of 3.6378 (16) Å, link mol­ecules along [001]. PMID:23476226

Reaction of carbon dioxide with a palladium-alkyl complex supported by a bis-NHC framework.

PubMed

Ariyananda, Piyal W G; Yap, Glenn P A; Rosenthal, Joel

2012-07-14

The reactivity of a dimethyl palladium complex supported by a dicarbene chelate (MDC(Mes))PdMe(2) towards CO(2) has been investigated. In the presence of trace H(2)O, this reaction yields the corresponding methyl bicarbonate complex (MDC(Mes))PdMe(O(2)COH), which goes on to give the corresponding κ(2)-carbonato complex upon crystallization (MDC(Mes))Pd(CO(3)). This chemistry, as well as related protonolysis by acetic acid was monitored by a combination of techniques including React-IR spectroscopy.

Synthesis, characterization and properties of carbon nanotubes microspheres from pyrolysis of polypropylene and maleated polypropylene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Junhao, E-mail: jhzhang6@mail.ustc.edu.cn; Department of Chemistry, University of Science and Technology of China, Heifei, Anhui 230026; Du, Jin

Microspheres assembled from carbon nanotubes (MCNTs), with the diameters ranging from 5.5 to 7.5 {mu}m, were synthesized by means of pyrolysis of polypropylene and maleated polypropylene in an autoclave. The characterization of structure and morphology was carried out by X-ray diffractometer (XRD), field-emission scanning electron microscopy (FESEM), (high resolution) transmission electron microscope [(HR)TEM)], selected-area electron diffraction (SAED) and Raman spectrum. As a typical morphology, the possible growth process of MCNTs was also investigated and discussed. The results of nitrogen adsorption-desorption indicate that the Brunauer-Emett-Teller (BET) surface area (140.6 m{sup 2}/g) of the MCNTs obtained at 600 {sup o}C is aboutmore » twice as that (74.5 m{sup 2}/g) of carbon nanotubes obtained at 700 {sup o}C. The results of catalytic experiment show that MCNTs based catalyst has higher catalytic activity than the carbon nanotubes based catalyst for the preparation of methanol and dimethoxy-ethane by oxidation of dimethyl ether.« less

40 CFR 721.10159 - 1-Docosanamine, N,N-dimethyl-.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1-Docosanamine, N,N-dimethyl-. 721... Substances § 721.10159 1-Docosanamine, N,N-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as 1-docosanamine, N,N-dimethyl- (PMN P-07-587...

40 CFR 180.261 - N-(Mercaptomethyl) phthali-mide S-(O,O-dimethyl phosphoro-dithioate) and its oxygen analog...

Code of Federal Regulations, 2010 CFR

2010-07-01

...-dimethyl phosphoro-dithioate) and its oxygen analog; tolerances for residues. 180.261 Section 180.261...-mide S-(O,O-dimethyl phosphoro-dithioate) and its oxygen analog; tolerances for residues. (a) General...-(O,O-dimethyl phosphorodithioate) and its oxygen analog N-(mercaptomethyl) phthalimide S-(O,O...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Benzene, 1,2-dimethyl-, poly-propene... Significant New Uses for Specific Chemical Substances § 721.1225 Benzene, 1,2-dimethyl-, poly-propene... reporting. (1) The chemical substance identified as benzene, 1,2-dimethyl-, polypropene derivatives...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Benzene, 1,2-dimethyl-, poly-propene... Significant New Uses for Specific Chemical Substances § 721.1225 Benzene, 1,2-dimethyl-, poly-propene... reporting. (1) The chemical substance identified as benzene, 1,2-dimethyl-, polypropene derivatives...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Benzene, 1,2-dimethyl-, poly-propene... Significant New Uses for Specific Chemical Substances § 721.1225 Benzene, 1,2-dimethyl-, poly-propene... reporting. (1) The chemical substance identified as benzene, 1,2-dimethyl-, polypropene derivatives...

40 CFR 721.10159 - 1-Docosanamine, N,N-dimethyl-.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Docosanamine, N,N-dimethyl-. 721... Substances § 721.10159 1-Docosanamine, N,N-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as 1-docosanamine, N,N-dimethyl- (PMN P-07-587...

Highly ordered and ultra-long carbon nanotube arrays as air cathodes for high-energy-efficiency Li-oxygen batteries

NASA Astrophysics Data System (ADS)

Yu, Ruimin; Fan, Wugang; Guo, Xiangxin; Dong, Shaoming

2016-02-01

Carbonaceous air cathodes with rational architecture are vital for the nonaqueous Li-O2 batteries to achieve large energy density, high energy efficiency and long cycle life. In this work, we report the cathodes made of highly ordered and vertically aligned carbon nanotubes grown on permeable Ta foil substrates (VACNTs-Ta) via thermal chemical vapour deposition. The VACNTs-Ta, composed of uniform carbon nanotubes with approximately 240 μm in superficial height, has the super large surface area. Meanwhile, the oriented carbon nanotubes provide extremely outstanding passageways for Li ions and oxygen species. Electrochemistry tests of VACNTs-Ta air cathodes show enhancement in discharge capacity and cycle life compared to those made from short-range oriented and disordered carbon nanotubes. By further combining with the LiI redox mediator that is dissolved in the tetraethylene dimethyl glycol based electrolytes, the batteries exhibit more than 200 cycles at the current density of 200 mA g-1 with a cut-off discharge capacity of 1000 mAh g-1, and their energy efficiencies increase from 50% to 82%. The results here demonstrate the importance of cathode construction for high-energy-efficiency and long-life Li-O2 batteries.

Electrolytes for Low-Temperature Operation of Li-CFx Cells

NASA Technical Reports Server (NTRS)

Smart, Marshall C.; Whitacre, Jay F.; Bugga, Ratnakumar V.; Prakash, G. K. Surya; Bhalla, Pooja; Smith, Kiah

2009-01-01

A report describes a study of electrolyte compositions selected as candidates for improving the low-temperature performances of primary electrochemical cells that contain lithium anodes and fluorinated carbonaceous (CFx) cathodes. This study complements the developments reported in Additive for Low-Temperature Operation of Li-(CF)n Cells (NPO- 43579) and Li/CFx Cells Optimized for Low-Temperature Operation (NPO- 43585), which appear elsewhere in this issue of NASA Tech Briefs. Similar to lithium-based electrolytes described in several previous NASA Tech Briefs articles, each of these electrolytes consisted of a lithium salt dissolved in a nonaqueous solvent mixture. Each such mixture consisted of two or more of the following ingredients: propylene carbonate (PC); 1,2-dimethoxyethane (DME); trifluoropropylene carbonate; bis(2,2,2-trifluoroethyl) ether; diethyl carbonate; dimethyl carbonate; and ethyl methyl carbonate. The report describes the physical and chemical principles underlying the selection of the compositions (which were not optimized) and presents results of preliminary tests made to determine effects of the compositions upon the low-temperature capabilities of Li-CFx cells, relative to a baseline composition of LiBF4 at a concentration of 1.0 M in a solvent comprising equal volume parts of PC and DME.

Differentiation of isomeric 2-aryldimethyltetrahydro-5-quinolinones by electron ionization and electrospray ionization mass spectrometry.

PubMed

Kumar, Ch Dinesh; Chary, V Naresh; Dinesh, A; Reddy, P S; Srinivas, K; Gayatri, G; Sastry, G N; Prabhakar, S

2011-10-15

A series of isomeric 2-aryl-6,6-dimethyltetrahydro-5-quinolinones (set I) and 2-aryl-7,7-dimethyltetrahydro-5-quinolinones (set II) were studied under positive ion electron ionization (EI) and electrospray ionization (ESI) techniques. Under EI conditions, the molecular ions were found to be less stable in set I isomers, and they resulted in abundant fragment ions, i.e., [M-CH(3)](+), [M-CO](+.), [M-HCO](+), [M-(CH(3),CO)](+), and [M-(CH(3),CH(2)O)](+), when compared with set II isomers. In addition, the set I isomers showed specific fragment ions corresponding to [M-OH](+) and [M-OCH(3)](+). The retro-Diels-Alder (RDA) product ion was always higher in set II isomers. The ESI mass spectra produced [M + H](+) ions, and their decomposition showed favorable loss of CH(3) radical, CH(4) and C(2)H(6) molecules in set I isomers. The set II isomers, however, showed predominant RDA product ions, and specific loss of H(2)O. The selectivity in EI and ESI was attributed to the instability of set I isomers by the presence of a gem-dimethyl group at the α-position, and it was supported by the data from model compounds without a gem-dimethyl group. Density functional theory (DFT) calculations successfully corroborated the fragmentation pathways for diagnostic ions. This study revealed the effect of a gem-dimethyl group located at the α-position to the carbonyl having aromatic/unsaturated carbon on the other side of the carbonyl group. Copyright © 2011 John Wiley & Sons, Ltd.

40 CFR 721.10366 - Benzene, 4-bromo-1,2-dimethyl-.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Benzene, 4-bromo-1,2-dimethyl-. 721... Substances § 721.10366 Benzene, 4-bromo-1,2-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as benzene, 4-bromo-1,2-dimethyl-(PMN P-10-76...

40 CFR 721.10366 - Benzene, 4-bromo-1,2-dimethyl-.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Benzene, 4-bromo-1,2-dimethyl-. 721... Substances § 721.10366 Benzene, 4-bromo-1,2-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as benzene, 4-bromo-1,2-dimethyl-(PMN P-10-76...

40 CFR 721.10366 - Benzene, 4-bromo-1,2-dimethyl-.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Benzene, 4-bromo-1,2-dimethyl-. 721... Substances § 721.10366 Benzene, 4-bromo-1,2-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as benzene, 4-bromo-1,2-dimethyl-(PMN P-10-76...

Metathesis process for preparing an alpha, omega-functionalized olefin

DOEpatents

Burdett, Kenneth A.; Mokhtarzadeh, Morteza; Timmers, Francis J.

2010-10-12

A cross-metathesis process for preparing an .alpha.,.omega.-functionalized olefin, such as methyl 9-decenoate, and an .alpha.-olefin having three or more carbon atoms, such as 1-decene. The process involves contacting in a first reaction zone an .alpha.-functionalized internal olefin, such as methyl oleate, and an .alpha.-olefinic monomer having three or more carbon atoms, such as 1-decene, with a first metathesis catalyst to prepare an effluent stream containing the .alpha.,.omega.-functionalized olefin, such as methyl 9-decenoate, an unfunctionalized internal olefin, such as 9-octadecene, unconverted reactant olefins, and optionally, an .alpha.,.omega.-difunctionalized internal olefinic dimer, such as dimethyl 9-octadecen-1,18-dioate; separating said effluent streams; then contacting in a second reaction zone the unfunctionalized internal olefin with ethylene in the presence of a second metathesis catalyst to obtain a second product effluent containing the .alpha.-olefinic monomer having three or more carbon atoms; and cycling a portion of the .alpha.-olefinic monomer stream(s) to the first zone.

An operando FTIR spectroscopic and kinetic study of carbon monoxide pressure influence on rhodium-catalyzed olefin hydroformylation.

PubMed

Kubis, Christoph; Sawall, Mathias; Block, Axel; Neymeyr, Klaus; Ludwig, Ralf; Börner, Armin; Selent, Detlef

2014-09-08

The influence of carbon monoxide concentration on the kinetics of the hydroformylation of 3,3-dimethyl-1-butene with a phosphite-modified rhodium catalyst has been studied for the pressure range p(CO)=0.20-3.83 MPa. Highly resolved time-dependent concentration profiles of the organometallic intermediates were derived from IR spectroscopic data collected in situ for the entire olefin-conversion range. The dynamics of the catalyst and organic components are described by enzyme-type kinetics with competitive and uncompetitive inhibition reactions involving carbon monoxide taken into account. Saturation of the alkyl-rhodium intermediates with carbon monoxide as a cosubstrate occurs between 1.5 and 2 MPa of carbon monoxide pressure, which brings about a convergence of aldehyde regioselectivity. Hydrogenolysis of the acyl intermediate is fast at 30 °C and low pressure of p(CO)=0.2 MPa, but is of minus first order with respect to the solution concentration of carbon monoxide. Resting 18-electron hydrido and acyl complexes that correspond to early and late rate-determining states, respectively, coexist as long as the conversion of the substrate is not complete. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

This program summary describes each of the DOE's Biomass Energy System's projects funded or in existence during fiscal year 1979 and reflects their status as of September 30, 1979. The summary provides an overview of the ongoing research, development, and demonstration efforts of the preceding fiscal year as well. (DMC)

H3 K79 dimethylation marks developmental activation of the beta-globin gene but is reduced upon LCR-mediated high-level transcription.

PubMed

Sawado, Tomoyuki; Halow, Jessica; Im, Hogune; Ragoczy, Tobias; Bresnick, Emery H; Bender, M A; Groudine, Mark

2008-07-15

Genome-wide analyses of the relationship between H3 K79 dimethylation and transcription have revealed contradictory results. To clarify this relationship at a single locus, we analyzed expression and H3 K79 modification levels of wild-type (WT) and transcriptionally impaired beta-globin mutant genes during erythroid differentiation. Analysis of fractionated erythroid cells derived from WT/Delta locus control region (LCR) heterozygous mice reveals no significant H3 K79 dimethylation of the beta-globin gene on either allele prior to activation of transcription. Upon transcriptional activation, H3 K79 di-methylation is observed along both WT and DeltaLCR alleles, and both alleles are located in proximity to H3 K79 dimethylation nuclear foci. However, H3 K79 di-methylation is significantly increased along the DeltaLCR allele compared with the WT allele. In addition, analysis of a partial LCR deletion mutant reveals that H3 K79 dimethylation is inversely correlated with beta-globin gene expression levels. Thus, while our results support a link between H3 K79 dimethylation and gene expression, high levels of this mark are not essential for high level beta-globin gene transcription. We propose that H3 K79 dimethylation is destabilized on a highly transcribed template.

Isolation and Characterization of 4-tert-Butylphenol-Utilizing Sphingobium fuliginis Strains from Phragmites australis Rhizosphere Sediment▿ †

PubMed Central

Toyama, Tadashi; Momotani, Naonori; Ogata, Yuka; Miyamori, Yuji; Inoue, Daisuke; Sei, Kazunari; Mori, Kazuhiro; Kikuchi, Shintaro; Ike, Michihiko

2010-01-01

We isolated three Sphingobium fuliginis strains from Phragmites australis rhizosphere sediment that were capable of utilizing 4-tert-butylphenol as a sole carbon and energy source. These strains are the first 4-tert-butylphenol-utilizing bacteria. The strain designated TIK-1 completely degraded 1.0 mM 4-tert-butylphenol in basal salts medium within 12 h, with concomitant cell growth. We identified 4-tert-butylcatechol and 3,3-dimethyl-2-butanone as internal metabolites by gas chromatography-mass spectrometry. When 3-fluorocatechol was used as an inactivator of meta-cleavage enzymes, strain TIK-1 could not degrade 4-tert-butylcatechol and 3,3-dimethyl-2-butanone was not detected. We concluded that metabolism of 4-tert-butylphenol by strain TIK-1 is initiated by hydroxylation to 4-tert-butylcatechol, followed by a meta-cleavage pathway. Growth experiments with 20 other alkylphenols showed that 4-isopropylphenol, 4-sec-butylphenol, and 4-tert-pentylphenol, which have alkyl side chains of three to five carbon atoms with α-quaternary or α-tertiary carbons, supported cell growth but that 4-n-alkylphenols, 4-tert-octylphenol, technical nonylphenol, 2-alkylphenols, and 3-alkylphenols did not. The rate of growth on 4-tert-butylphenol was much higher than that of growth on the other alkylphenols. Degradation experiments with various alkylphenols showed that strain TIK-1 cells grown on 4-tert-butylphenol could degrade 4-alkylphenols with variously sized and branched side chains (ethyl, n-propyl, isopropyl, n-butyl, sec-butyl, tert-butyl, n-pentyl, tert-pentyl, n-hexyl, n-heptyl, n-octyl, tert-octyl, n-nonyl, and branched nonyl) via a meta-cleavage pathway but not 2- or 3-alkylphenols. Along with the degradation of these alkylphenols, we detected methyl alkyl ketones that retained the structure of the original alkyl side chains. Strain TIK-1 may be useful in the bioremediation of environments polluted by 4-tert-butylphenol and various other 4-alkylphenols. PMID:20802076

40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

Code of Federal Regulations, 2014 CFR

2014-07-01

...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

Code of Federal Regulations, 2013 CFR

2013-07-01

...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

Code of Federal Regulations, 2012 CFR

2012-07-01

...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

40 CFR 721.10408 - Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene...

Code of Federal Regulations, 2013 CFR

2013-07-01

...)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2,2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl)oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...

40 CFR 721.10408 - Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene...

Code of Federal Regulations, 2014 CFR

2014-07-01

...)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2,2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl)oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...

40 CFR 721.10408 - Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene...

Code of Federal Regulations, 2012 CFR

2012-07-01

...)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2,2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl)oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...

Biological Implications in Cassava for the Production of Amylose-Free Starch: Impact on Root Yield and Related Traits

PubMed Central

Karlström, Amanda; Calle, Fernando; Salazar, Sandra; Morante, Nelson; Dufour, Dominique; Ceballos, Hernán

2016-01-01

Cassava (Manihot esculenta, Crantz) is an important food security crop, but it is becoming an important raw material for different industrial applications. Cassava is the second most important source of starch worldwide. Novel starch properties are of interest to the starch industry, and one them is the recently identified amylose-free (waxy) cassava starch. Waxy mutants have been found in different crops and have been often associated with a yield penalty. There are ongoing efforts to develop commercial cassava varieties with amylose-free starch. However, little information is available regarding the biological and agronomic implications of starch mutations in cassava, nor in other root and tuber crops. In this study, siblings from eight full-sib families, segregating for the waxy trait, were used to determine if the mutation has implications for yield, dry matter content (DMC) and harvest index in cassava. A total of 87 waxy and 87 wild-type starch genotypes from the eight families were used in the study. The only significant effect of starch type was on DMC (p < 0.01), with waxy clones having a 0.8% lower content than their wild type counterparts. There was no effect of starch type on fresh root yield (FRY), adjusted FRY and harvest index. It is not clear if lower DMC is a pleiotropic effect of the waxy starch mutation or else the result of linked genes introgressed along with the mutation. It is expected that commercial waxy cassava varieties will have competitive FRYs but special efforts will be required to attain adequate DMCs. This study contributes to the limited knowledge available of the impact of starch mutations on the agronomic performance of root and tuber crops. PMID:27242813

Data management of clinical trials during an outbreak of Ebola virus disease.

PubMed

Hossmann, Stefanie; Haynes, Alan G; Spoerri, Adrian; Diatta, Ibrahima Dina; Aboubacar, Barry; Egger, Matthias; Rintelen, Felix; Trelle, Sven

2017-10-23

Clinical trial data management (DM) conducted during outbreaks like that of Ebola virus disease (EVD) in West Africa, 2014-2016, has to adapt to specific, unique circumstances. CTU Bern was asked to set up a safe data capture/management system that could be launched within a few weeks and cover two different vaccine trials. This article describes some of the challenges we faced and our solutions during the two different trials. Setting up a DM system was split into four phases/tasks: (1) quick set-up of the (electronic) data capture system (EDC) and mobile infrastructure in Bern, (2) moving the EDC and infrastructure to Conakry, Guinea and implementation of a local data management centre (DMC), (3) running the DMC, and (4) data cleaning. The DMC had to meet the following criteria: (1) quick implementation, (2) efficient maintenance and handling of data, and (3) procedures to guarantee data quality. The EDC (REDCap) was setup as a local area network. In order to ensure high data quality, double data entry, and then review of inconsistencies and offline plausibility checks were implemented. From the start of CTU Bern's involvement to the productive EDC took 11 weeks. It was necessary to adapt processes for dealing with data continuously throughout the trial conduct phase. The data management team processed 171,794 case report form pages from a total of 14,203 participants in the period between March and December 2015. Data management is a key task supporting trial conduct. For trials in emergency situations, many of our approaches are suitable, but we also provide a list of aspects that might be done differently. Copyright © 2017. Published by Elsevier Ltd.

Use of the Delay-Tolerant Networking Bundle Protocol from Space

NASA Technical Reports Server (NTRS)

Wood, Lloyd; Ivancic, William D.; Eddy, Wesley M.; Stewart, Dave; Northam, James; Jackson, Chris; daSilvaCuriel, Alex

2009-01-01

The Disaster Monitoring Constellation (DMC), constructed by Survey Satellite Technology Ltd (SSTL), is a multisatellite Earth-imaging low-Earth-orbit sensor network where captured image swaths are stored onboard each satellite and later downloaded from the satellite payloads to a ground station. Store-and-forward of images with capture and later download gives each satellite the characteristics of a node in a Delay/Disruption Tolerant Network (DTN). Originally developed for the Interplanetary Internet, DTNs are now under investigation in an Internet Research Task Force (IRTF) DTN research group (RG), which has developed a bundle architecture and protocol. The DMC is currently unique in its adoption of the Internet Protocol (IP) for its imaging payloads and for satellite command and control, based around reuse of commercial networking and link protocols. These satellites use of IP has enabled earlier experiments with the Cisco router in Low Earth Orbit (CLEO) onboard the constellation's UK-DMC satellite. Earth images are downloaded from the satellites using a custom IPbased high-speed transfer protocol developed by SSTL, Saratoga, which tolerates unusual link environments. Saratoga has been documented in the Internet Engineering Task Force (IETF) for wider adoption. We experiment with use of DTNRG bundle concepts onboard the UKDMC satellite, by examining how Saratoga can be used as a DTN convergence layer to carry the DTNRG Bundle Protocol, so that sensor images can be delivered to ground stations and beyond as bundles. This is the first successful use of the DTNRG Bundle Protocol in a space environment. We use our practical experience to examine the strengths and weaknesses of the Bundle Protocol for DTN use, paying attention to fragmentation, custody transfer, and reliability issues.

The CpG island encompassing the promoter and first exon of human DNMT3L gene is a PcG/TrX response element (PRE).

PubMed

Basu, Amitava; Dasari, Vasanthi; Mishra, Rakesh K; Khosla, Sanjeev

2014-01-01

DNMT3L, a member of DNA methyltransferases family, is present only in mammals. As it provides specificity to the action of de novo methyltransferases, DNMT3A and DNMT3B and interacts with histone H3, DNMT3L has been invoked as the molecule that can read the histone code and translate it into DNA methylation. It plays an important role in the initiation of genomic imprints during gametogenesis and in nuclear reprogramming. With important functions attributed to it, it is imperative that the DNMT3L expression is tightly controlled. Previously, we had identified a CpG island within the human DNMT3L promoter and first exon that showed loss of DNA methylation in cancer samples. Here we show that this Differentially Methylated CpG island within DNMT3L (DNMT3L DMC) acts to repress transcription, is a Polycomb/Trithorax Response Element (PRE) and interacts with both PRC1 and PRC2 Polycomb repressive complexes. In addition, it adopts inactive chromatin conformation and is associated with other inactive chromatin-specific proteins like SUV39H1 and HP1. The presence of DNMT3L DMC also influences the adjacent promoter to adopt repressive histone post-translational modifications. Due to its association with multiple layers of repressive epigenetic modifications, we believe that PRE within the DNMT3L DMC is responsible for the tight regulation of DNMT3L expression and the aberrant epigenetic modifications of this region leading to DNMT3L overexpression could be the reason of nuclear programming during carcinogenesis.

Full-dimensional quantum calculations of ground-state tunneling splitting of malonaldehyde using an accurate ab initio potential energy surface

NASA Astrophysics Data System (ADS)

Wang, Yimin; Braams, Bastiaan J.; Bowman, Joel M.; Carter, Stuart; Tew, David P.

2008-06-01

Quantum calculations of the ground vibrational state tunneling splitting of H-atom and D-atom transfer in malonaldehyde are performed on a full-dimensional ab initio potential energy surface (PES). The PES is a fit to 11 147 near basis-set-limit frozen-core CCSD(T) electronic energies. This surface properly describes the invariance of the potential with respect to all permutations of identical atoms. The saddle-point barrier for the H-atom transfer on the PES is 4.1 kcal/mol, in excellent agreement with the reported ab initio value. Model one-dimensional and ``exact'' full-dimensional calculations of the splitting for H- and D-atom transfer are done using this PES. The tunneling splittings in full dimensionality are calculated using the unbiased ``fixed-node'' diffusion Monte Carlo (DMC) method in Cartesian and saddle-point normal coordinates. The ground-state tunneling splitting is found to be 21.6 cm-1 in Cartesian coordinates and 22.6 cm-1 in normal coordinates, with an uncertainty of 2-3 cm-1. This splitting is also calculated based on a model which makes use of the exact single-well zero-point energy (ZPE) obtained with the MULTIMODE code and DMC ZPE and this calculation gives a tunneling splitting of 21-22 cm-1. The corresponding computed splittings for the D-atom transfer are 3.0, 3.1, and 2-3 cm-1. These calculated tunneling splittings agree with each other to within less than the standard uncertainties obtained with the DMC method used, which are between 2 and 3 cm-1, and agree well with the experimental values of 21.6 and 2.9 cm-1 for the H and D transfer, respectively.

Full-dimensional quantum calculations of ground-state tunneling splitting of malonaldehyde using an accurate ab initio potential energy surface.

PubMed

Wang, Yimin; Braams, Bastiaan J; Bowman, Joel M; Carter, Stuart; Tew, David P

2008-06-14

Quantum calculations of the ground vibrational state tunneling splitting of H-atom and D-atom transfer in malonaldehyde are performed on a full-dimensional ab initio potential energy surface (PES). The PES is a fit to 11 147 near basis-set-limit frozen-core CCSD(T) electronic energies. This surface properly describes the invariance of the potential with respect to all permutations of identical atoms. The saddle-point barrier for the H-atom transfer on the PES is 4.1 kcalmol, in excellent agreement with the reported ab initio value. Model one-dimensional and "exact" full-dimensional calculations of the splitting for H- and D-atom transfer are done using this PES. The tunneling splittings in full dimensionality are calculated using the unbiased "fixed-node" diffusion Monte Carlo (DMC) method in Cartesian and saddle-point normal coordinates. The ground-state tunneling splitting is found to be 21.6 cm(-1) in Cartesian coordinates and 22.6 cm(-1) in normal coordinates, with an uncertainty of 2-3 cm(-1). This splitting is also calculated based on a model which makes use of the exact single-well zero-point energy (ZPE) obtained with the MULTIMODE code and DMC ZPE and this calculation gives a tunneling splitting of 21-22 cm(-1). The corresponding computed splittings for the D-atom transfer are 3.0, 3.1, and 2-3 cm(-1). These calculated tunneling splittings agree with each other to within less than the standard uncertainties obtained with the DMC method used, which are between 2 and 3 cm(-1), and agree well with the experimental values of 21.6 and 2.9 cm(-1) for the H and D transfer, respectively.

Quantifying and managing regional greenhouse gas emissions: waste sector of Daejeon, Korea.

PubMed

Yi, Sora; Yang, Heewon; Lee, Seung Hoon; An, Kyoung-Jin

2014-06-01

A credible accounting of national and regional inventories for the greenhouse gas (GHG) reduction has emerged as one of the most significant current discussions. This article assessed the regional GHG emissions by three categories of the waste sector in Daejeon Metropolitan City (DMC), Korea, examined the potential for DMC to reduce GHG emission, and discussed the methodology modified from Intergovernmental Panel on Climate Change and Korea national guidelines. During the last five years, DMC's overall GHG emissions were 239 thousand tons CO2 eq./year from eleven public environmental infrastructure facilities, with a population of 1.52 million. Of the three categories, solid waste treatment/disposal contributes 68%, whilst wastewater treatment and others contribute 22% and 10% respectively. Among GHG unit emissions per ton of waste treatment, the biggest contributor was waste incineration of 694 kg CO2 eq./ton, followed by waste disposal of 483 kg CO2 eq./ton, biological treatment of solid waste of 209 kg CO2 eq./ton, wastewater treatment of 0.241 kg CO2 eq./m(3), and public water supplies of 0.067 kg CO2 eq./m(3). Furthermore, it is suggested that the potential in reducing GHG emissions from landfill process can be as high as 47.5% by increasing landfill gas recovery up to 50%. Therefore, it is apparent that reduction strategies for the main contributors of GHG emissions should take precedence over minor contributors and lead to the best practice for managing GHGs abatement. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

Adsorption Characteristics of Bixin on Acid- and Alkali-Treated Kaolinite in Aprotic Solvents

PubMed Central

Rahmalia, Winda; Fabre, Jean-François; Usman, Thamrin

2018-01-01

The adsorption of bixin in aprotic solvents onto acid- and alkali-treated kaolinite was investigated. Kaolinite was treated three times, for 6 h each, with 8 M HCl or 5 M KOH. The adsorbents were characterized by XRD, FT-IR, EDS, and BET-N2. The effects of contact time and dye concentration on adsorption capacity and kinetics, electronic transition of bixin before and after adsorption, and also mechanism of bixin-kaolinite adsorption were investigated. Dye adsorption followed pseudo-second order kinetics and was faster in acetone than in dimethyl carbonate. The best adsorption results were obtained for KOH-treated kaolinite. In both of the solvents, the adsorption isotherm followed the Langmuir model and adsorption capacity was higher in dimethyl carbonate (q m = 0.43 mg/g) than in acetone (0.29 mg/g). The adsorption capacity and kinetics of KOH-treated kaolinite (q m = 0.43 mg/g, k 2 = 3.27 g/mg·min) were better than those of HCl-treated kaolinite (q m = 0.21 mg/g, k 2 = 0.25 g/mg·min) and natural kaolinite (q m = 0.18 mg/g, k 2 = 0.32 g/mg·min). There are shift in the band position of maximum intensity of bixin after adsorption on this adsorbent. Adsorption in this system seemed to be based essentially on chemisorption due to the electrostatic interaction of bixin with the strong basic and reducing sites of kaolinite. PMID:29581720

Generation and characterization of a distonic biradical anion formed from an enediynone prodrug in the gas phase.

PubMed

Yang, Linan; Bekele, Tefsit; Lipton, Mark A; Kenttämaa, Hilkka I

2013-04-01

A negatively charged biradical intermediate was successfully generated in the gas phase via cyclization of the deprotonated bicyclo[8.3.0]trideca-12-ene-2,7-diyn-1-one precursor. The inherent negative charge of this biradical allows its characterization via collision-activated dissociation and reactions with a variety of neutral substrates in an FT-ICR mass spectrometer. Although the biradical is unreactive toward reagents that usually react rapidly with positively charged biradicals, such as dimethyl disulfide, it reacts with the halogen-containing substrates carbon tetrachloride, carbon tetrabromide, and bromotrichloromethane via bromine or chlorine atom abstraction, which supports its biradical structure. The results presented in this study indicate that cyclizations commonly used in solution to form biradical intermediates from enediyne compounds may also occur in the gas phase.

Generation and Characterization of a Distonic Biradical Anion Formed from an Enediynone Prodrug in the Gas Phase

PubMed Central

Yang, Linan; Bekele, Tefsit; Lipton, Mark A.

2013-01-01

A negatively charged biradical intermediate was successfully generated in the gas phase via cyclization of the deprotonated bicyclo[8.3.0]trideca-12-ene-2,7-diyn-1-one precursor. The inherent negative charge of this biradical allows its characterization via collision-activated dissociation and reactions with a variety of neutral substrates in an FT-ICR mass spectrometer. Although the biradical is unreactive toward reagents that usually react rapidly with positively charged biradicals, such as dimethyl disulfide, it reacts with the halogen-containing substrates carbon tetrachloride, carbon tetrabromide and bromotrichloromethane via bromine or chlorine atom abstraction, which supports its biradical structure. The results presented in this study indicate that cyclizations commonly used in solution to form biradical intermediates from enediyne compounds may also occur in the gas phase. PMID:23512422

A Nonaqueous Potassium-Based Battery-Supercapacitor Hybrid Device.

PubMed

Fan, Ling; Lin, Kairui; Wang, Jue; Ma, Ruifang; Lu, Bingan

2018-05-01

A low cost nonaqueous potassium-based battery-supercapacitor hybrid device (BSH) is successfully established for the first time with soft carbon as the anode, commercialized activated carbon as the cathode, and potassium bis(fluoro-slufonyl)imide in dimethyl ether as the electrolyte. This BSH reconciles the advantages of potassium ion batteries and supercapacitors, achieving a high energy density of 120 W h kg -1 , a high power density of 599 W kg -1 , a long cycle life of 1500 cycles, and an ultrafast charge/slow discharge performance (energy density and power density are calculated based on the total mass of active materials in the anode and cathode). This work demonstrates a great potential of applying the nonaqueous BSH for low cost electric energy storage systems. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Environmentally-friendly lithium recycling from a spent organic li-ion battery.

PubMed

Renault, Stéven; Brandell, Daniel; Edström, Kristina

2014-10-01

A simple and straightforward method using non-polluting solvents and a single thermal treatment step at moderate temperature was investigated as an environmentally-friendly process to recycle lithium from organic electrode materials for secondary lithium batteries. This method, highly dependent on the choice of electrolyte, gives up to 99% of sustained capacity for the recycled materials used in a second life-cycle battery when compared with the original. The best results were obtained using a dimethyl carbonate/lithium bis(trifluoromethane sulfonyl) imide electrolyte that does not decompose in presence of water. The process implies a thermal decomposition step at a moderate temperature of the extracted organic material into lithium carbonate, which is then used as a lithiation agent for the preparation of fresh electrode material without loss of lithium. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Predicting Global Rates and Distribution of Carbonate Melting Beneath the Ocean Basins: Implications for the Origin of the Gutenberg Discontinuity

NASA Astrophysics Data System (ADS)

Clerc, F.; Behn, M. D.; Parmentier, E. M.

2017-12-01

The pooling of carbonate melts beneath old ocean lithosphere is a proposed explanation for the seismic Gutenberg (G) discontinuity. However, while the G discontinuity is observed ubiquitously across the ocean basins, carbonate melting only occurs in regions of mantle upwelling. Here we examine the global distribution and extent of carbonate melting by coupling a mantle flow model with a thermodynamic parameterization for carbonate melting. We obtain global upwelling velocities from a convection model driven by plate motions and mantle density differences [1], and calculate melt fractions from the R_DMC carbonate solidus [2]. We find low-degree carbonate melts are produced pervasively throughout ocean basins, driven by passive upwelling in response to subduction. Assuming melt formed within 100 km of the ridge is focused to its axis, our model predicts a 6-km thick oceanic crust and a global CO2 ridge flux of 7 x 1011 mol/yr (for a mantle source concentration of 100 ppm CO2). This flux is consistent with other estimates of CO2 ridge fluxes [e.g.,3] over the inferred range of MORB-source mantle carbon concentrations [e.g.,4]. In addition to the ridge flux, off-axis carbonate melting results in a global CO2 flux of 1.6 x 1012mol/yr. To test for correlations between regions of upwelling-induced carbonate melting and seismic evidence for the LAB, we compare our results with a compilation of seismic G discontinuity observations [5]. While most observations of the G discontinuity are found in regions of predicted carbonate melting, some lie in regions of downwelling (where no melting occurs), suggesting that melt pooling does not conclusively explain these seismic signals. Further, we estimate off-axis porosities to be < 0.1%, indicating that the melt remaining in the mantle does not contribute substantially to a discontinuity of the observed magnitude. Carbonate melts pooled at the base of the lithosphere may refreeze within the thermal boundary layer and refertilize the lithosphere. We model the trace element compositions of these enriched melts and compare them with geochemical data from enriched mantle sources, such as petit-spot melts [e.g.,6]. [1] Naliboff et al., GRL, 2009; [2] Keller & Katz, J Pet, 2016; [3] Chavrit et al., EPSL, 2014; [4] Rosenthal et al., EPSL, 2015; [5] Schmerr, Sci, 2012; [6] Machida et al., EPSL, 2015

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2013 CFR

2013-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2012 CFR

2012-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2011 CFR

2011-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2014 CFR

2014-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts (PMN P-03-46; CAS No. 136504-87-5) is subject to...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts (PMN P-03-46; CAS No. 136504-87-5) is subject to...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts (PMN P-03-46; CAS No. 136504-87-5) is subject to...

40 CFR 721.10174 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts. 721.10174 Section 721.10174 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts. (a) Chemical substance...-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts (PMN P-04-139...

Puzzle of magnetic moments of Ni clusters revisited using quantum Monte Carlo method.

PubMed

Lee, Hung-Wen; Chang, Chun-Ming; Hsing, Cheng-Rong

2017-02-28

The puzzle of the magnetic moments of small nickel clusters arises from the discrepancy between values predicted using density functional theory (DFT) and experimental measurements. Traditional DFT approaches underestimate the magnetic moments of nickel clusters. Two fundamental problems are associated with this puzzle, namely, calculating the exchange-correlation interaction accurately and determining the global minimum structures of the clusters. Theoretically, the two problems can be solved using quantum Monte Carlo (QMC) calculations and the ab initio random structure searching (AIRSS) method correspondingly. Therefore, we combined the fixed-moment AIRSS and QMC methods to investigate the magnetic properties of Ni n (n = 5-9) clusters. The spin moments of the diffusion Monte Carlo (DMC) ground states are higher than those of the Perdew-Burke-Ernzerhof ground states and, in the case of Ni 8-9 , two new ground-state structures have been discovered using the DMC calculations. The predicted results are closer to the experimental findings, unlike the results predicted in previous standard DFT studies.

Improved diffusion Monte Carlo propagators for bosonic systems using Itô calculus

NASA Astrophysics Data System (ADS)

Hâkansson, P.; Mella, M.; Bressanini, Dario; Morosi, Gabriele; Patrone, Marta

2006-11-01

The construction of importance sampled diffusion Monte Carlo (DMC) schemes accurate to second order in the time step is discussed. A central aspect in obtaining efficient second order schemes is the numerical solution of the stochastic differential equation (SDE) associated with the Fokker-Plank equation responsible for the importance sampling procedure. In this work, stochastic predictor-corrector schemes solving the SDE and consistent with Itô calculus are used in DMC simulations of helium clusters. These schemes are numerically compared with alternative algorithms obtained by splitting the Fokker-Plank operator, an approach that we analyze using the analytical tools provided by Itô calculus. The numerical results show that predictor-corrector methods are indeed accurate to second order in the time step and that they present a smaller time step bias and a better efficiency than second order split-operator derived schemes when computing ensemble averages for bosonic systems. The possible extension of the predictor-corrector methods to higher orders is also discussed.

Case study of rotating sonar sensor application in unmanned automated guided vehicle

NASA Astrophysics Data System (ADS)

Chandak, Pravin; Cao, Ming; Hall, Ernest L.

2001-10-01

A single rotating sonar element is used with a restricted angle of sweep to obtain readings to develop a range map for the unobstructed path of an autonomous guided vehicle (AGV). A Polaroid ultrasound transducer element is mounted on a micromotor with an encoder feedback. The motion of this motor is controlled using a Galil DMC 1000 motion control board. The encoder is interfaced with the DMC 1000 board using an intermediate IMC 1100 break-out board. By adjusting the parameters of the Polaroid element, it is possible to obtain range readings at known angles with respect to the center of the robot. The readings are mapped to obtain a range map of the unobstructed path in front of the robot. The idea can be extended to a 360 degree mapping by changing the assembly level programming on the Galil Motion control board. Such a system would be compact and reliable over a range of environments and AGV applications.

Role for the Silencing Protein Dot1 in Meiotic Checkpoint Control

PubMed Central

San-Segundo, Pedro A.; Roeder, G. Shirleen

2000-01-01

During the meiotic cell cycle, a surveillance mechanism called the “pachytene checkpoint” ensures proper chromosome segregation by preventing meiotic progression when recombination and chromosome synapsis are defective. The silencing protein Dot1 (also known as Pch1) is required for checkpoint-mediated pachytene arrest of the zip1 and dmc1 mutants of Saccharomyces cerevisiae. In the absence of DOT1, the zip1 and dmc1 mutants inappropriately progress through meiosis, generating inviable meiotic products. Other components of the pachytene checkpoint include the nucleolar protein Pch2 and the heterochromatin component Sir2. In dot1, disruption of the checkpoint correlates with the loss of concentration of Pch2 and Sir2 in the nucleolus. In addition to its checkpoint function, Dot1 blocks the repair of meiotic double-strand breaks by a Rad54-dependent pathway of recombination between sister chromatids. In vegetative cells, mutation of DOT1 results in delocalization of Sir3 from telomeres, accounting for the impaired telomeric silencing in dot1. PMID:11029058

DOE Office of Scientific and Technical Information (OSTI.GOV)

Azadi, Sam, E-mail: s.azadi@ucl.ac.uk; Cohen, R. E.

We report an accurate study of interactions between benzene molecules using variational quantum Monte Carlo (VMC) and diffusion quantum Monte Carlo (DMC) methods. We compare these results with density functional theory using different van der Waals functionals. In our quantum Monte Carlo (QMC) calculations, we use accurate correlated trial wave functions including three-body Jastrow factors and backflow transformations. We consider two benzene molecules in the parallel displaced geometry, and find that by highly optimizing the wave function and introducing more dynamical correlation into the wave function, we compute the weak chemical binding energy between aromatic rings accurately. We find optimalmore » VMC and DMC binding energies of −2.3(4) and −2.7(3) kcal/mol, respectively. The best estimate of the coupled-cluster theory through perturbative triplets/complete basis set limit is −2.65(2) kcal/mol [Miliordos et al., J. Phys. Chem. A 118, 7568 (2014)]. Our results indicate that QMC methods give chemical accuracy for weakly bound van der Waals molecular interactions, comparable to results from the best quantum chemistry methods.« less

Antioxidant properties of dimethyl sulfoxide and its viability as a solvent in the evaluation of neuroprotective antioxidants.

PubMed

Sanmartín-Suárez, Carolina; Soto-Otero, Ramón; Sánchez-Sellero, Inés; Méndez-Álvarez, Estefanía

2011-01-01

Dimethyl sulfoxide is an amphiphilic compound whose miscibility with water and its ability to dissolve lipophilic compounds make it an appreciated solvent in biomedical research. However, its reported antioxidant properties raise doubts about its use as a solvent in evaluating new antioxidants. The goal of this investigation was to evaluate its antioxidant properties and carry out a comparative study on the antioxidant properties of some known neuroprotective antioxidants in the presence and absence of dimethyl sulfoxide. The antioxidant properties of dimethyl sulfoxide were studied in rat brain homogenates by determining its ability to reduce both lipid peroxidation (TBARS formation) and protein oxidation (increase in protein carbonyl content and decrease in free thiol content) induced by ferrous chloride/hydrogen peroxide. Its ability to reduce the production of hydroxyl radicals by 6-hydroxydopamine autoxidation was also estimated. The same study was also performed with three known antioxidants (α-phenyl-N-tert-butylnitrone; 2-methyl-2-nitrosopropane; 5,5-dimethyl-1-pyrroline N-oxide) in the presence and absence of dimethyl sulfoxide. Our results showed that dimethyl sulfoxide is able to reduce both lipid peroxidation and protein carbonyl formation induced by ferrous chloride/hydrogen peroxide in rat brain homogenates. It can also reduce the production of hydroxyl radicals during 6-hydroxydopamine autoxidation. However, it increases the oxidation of protein thiol groups caused by ferrous chloride/hydrogen peroxide in rat brain homogenate. Despite the here reported antioxidant and pro-oxidant properties of dimethyl sulfoxide, the results obtained with α-phenyl-N-tert-butylnitrone, 2-methyl-2-nitrosopropane, and 5,5-dimethyl-1-pyrroline N-oxide corroborate the antioxidant properties attributed to these compounds and support the potential use of dimethyl sulfoxide as a solvent in the study of the antioxidant properties of lipophilic compounds. Dimethyl sulfoxide is a very useful solvent that may be used at relatively low concentrations in the development of new antioxidants with neuroprotective properties. Copyright © 2010 Elsevier Inc. All rights reserved.

Enhanced Performance of a Lithium-Sulfur Battery Using a Carbonate-Based Electrolyte.

PubMed

Xu, Zhixin; Wang, Jiulin; Yang, Jun; Miao, Xiaowei; Chen, Renjie; Qian, Ji; Miao, Rongrong

2016-08-22

The lithium-sulfur battery is regarded as one of the most promising candidates for lithium-metal batteries with high energy density. However, dendrite Li formation and low cycle efficiency of the Li anode as well as unstable sulfur based cathode still hinder its practical application. Herein a novel electrolyte (1 m LiODFB/EC-DMC-FEC) is designed not only to address the above problems of Li anode but also to match sulfur cathode perfectly, leading to extraordinary electrochemical performances. Using this electrolyte, lithium|lithium cells can cycle stably for above 2000 hours and the average Coulumbic efficiency reaches 98.8 %. Moreover, the Li-S battery delivers a reversible capacity of about 1400 mAh g(-1) sulfur with retention of 89 % for 1100 cycles at 1 C, and a capacity above 1100 mAh g(-1) sulfur at 10 C. The more advantages of this cell system are its outstanding cycle stability at 60 °C and no self-discharge phenomena. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

75 FR 56094 - Delta-Mendota Canal Intertie Project

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-15

... and maintenance road along the canal would be used to set the transmission structures. Although span... access and maintenance road would be realigned where necessary to accommodate transmission line... DMC. The route also allowed use of the existing canal access and maintenance road to be used for...

Dynamic Constellation Tasking and Management

DTIC Science & Technology

2013-03-01

14 2.4. DARPA SeeMe Concept................................................................................20...11 Figure 3. DARPA SeeMe Satellite (Artist’s Concept) .................................................... 20 Figure 4...concept has not been adopted, it may one day find use with the DMC or other satellite systems. 2.4. DARPA SeeMe Concept The Defense Advance Research

New Photochrome Probe Allows Simultaneous pH and Microviscosity Sensing.

PubMed

Wu, Yuanyuan; Papper, Vladislav; Pokholenko, Oleksandr; Kharlanov, Vladimir; Zhou, Yubin; Steele, Terry W J; Marks, Robert S

2015-07-01

4-N,N'-dimethylamino-4'-N'-stilbenemaleamic acid (DASMA), a unique molecular photochrome probe that exhibits solubility and retains trans-cis photoisomerisation in a wide range of organic solvents and aqueous pH environments, was prepared, purified and chemically characterised. Absorption, fluorescence excitation and emission spectra and constant-illumination fluorescence decay were measured in acetonitrile, dimethyl sulfoxide, ethanol, propylene carbonate, and aqueous glycerol mixtures. The pseudo-first-order fluorescence decay rates were found to be strongly dependent on the medium viscosity. In addition, the molecule exhibited the pH-dependent fluorescence and photoisomerisation kinetics.

Investigation of polymer membranes modified by fullerenol for dehydration of organic mixtures

NASA Astrophysics Data System (ADS)

Dmitrenko, Mariia E.; Penkova, Anastasia V.; Kuzminova, Anna I.; Ermakov, Sergey S.; Roizard, Denis

2017-07-01

This study focuses on the development of novel dense and supported mixed-matrix membranes based on chitosan and poly(2,6-dimethyl-1,4-phenylenoxide) (PPO) with low-hydroxylated fullerenol C60(OH)12. These novel membranes containing nano-carbon particles were prepared to reach high membrane performances for further integration in a dehydration process like distillation coupled with pervaporation. SEM microscopy was used to visualize the internal morphology of the membrane. It was found that all membranes were well stable and highly water-selective in spite of the different nature of polymers.

Synthesis of racemic β-chamigrene, a spiro[5.5]undecane sequiterpene.

PubMed

Antonsen, Simen; Skattebøl, Lars; Stenstrøm, Yngve

2014-12-10

The present paper describes a total synthesis of racemic β-chamigrene, a sesquiterpene with a spiro[5.5]undecane carbon framework. Compared with previously reported β-chamigrene syntheses, we were able to reduce the total number of reaction steps, which also resulted in a significant improvement of the overall yield. The commercially available ketone 6-methylhept-5-en-2-one was transformed by known simple procedures into 3,3-dimethyl-2-methylenecyclohexanone. This reacted with isoprene by a Diels-Alder reaction to give a spiro ketone. An olefination reaction on this compound gave the target molecule.

Use of 2,5-dimethyl-2,5-hexane diamine as a curing agent for epoxy resins

DOEpatents

Rinde, J.A.; Newey, H.A.

1981-02-24

Primary diamines are disclosed of the formula shown in a diagram wherein R is a straight chain saturated hydrocarbon of 2 to 4 carbons, a disubstituted benzene ring, or disubstituted dibenzomethane for use as a curing agent for epoxy resins. These curing agents can be used to form epoxy resin mixtures useful in filament winding and pre-impregnated fiber molding and in formulating film adhesives, powder coatings and molding powders. The epoxy mixtures form for such uses as room temperature non-reacting, intermediate stable state which has a latent cross-linking capability.

Use of 2,5-dimethyl-2,5-hexane diamine as a curing agent for epoxy resins

DOEpatents

Rinde, James A. [Livermore, CA; Newey, Herbert A. [Lafayette, CA

1981-02-24

Primary diamines of the formula ##STR1## wherein R is a straight chain saturated hydrocarbon of 2 to 4 carbons, a disubstituted benzene ring, or disubstituted dibenzo methane for use as a curing agent for epoxy resins. These curing agents can be used to form epoxy resin mixtures useful in filament winding and pre-impregnated fiber molding and in formulating film adhesives, powder coatings and molding powders. The epoxy mixtures form for such uses as room temperature non-reacting, intermediate stable state which has a latent cross-linking capability.

Collection and analysis of organic gases from natural ecosystems - Application to poultry manure

NASA Technical Reports Server (NTRS)

Smith, M. S.; Francis, A. J.; Duxbury, J. M.

1977-01-01

Combined gas chromatography-mass spectrometry was used to identify volatile compounds generated from chicken manure and collected in Poropak QS-Carbosieve B traps. Various alcohols, ketones, esters, and carboxylic acids together with dimethyl sulfide and dimethyl disulfide were detected when the wastes were incubated in an argon atmosphere. Significant amounts of dimethyl sulfide and dimethyl disulfide but few other compounds were found when the manure was incubated in air

Protein-Mediated Precipitation of Calcium Carbonate

PubMed Central

Polowczyk, Izabela; Bastrzyk, Anna; Fiedot, Marta

2016-01-01

Calcium carbonate is an important component in exoskeletons of many organisms. The synthesis of calcium carbonate was performed by mixing dimethyl carbonate and an aqueous solution of calcium chloride dihydrate. The precipitation product was characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR) measurements. In addition, the turbidity of the reaction solution was acquired to monitor the kinetics of the calcium carbonate structure’s growth in the investigated system. In this study, samples of CaCO3 particles obtained with individual proteins, such as ovalbumin, lysozyme, and a mixture of the proteins, were characterized and compared with a control sample, i.e., synthesized without proteins. The obtained data indicated that the addition of ovalbumin to the reaction changed the morphology of crystals from rhombohedral to ‘stack-like’ structures. Lysozyme, however, did not affect the morphology of calcium carbonate, yet the presence of the protein mixture led to the creation of more complex composites in which the calcium carbonate crystals were constructed in protein matrices formed by the ovalbumin-lysozyme interaction. It was also observed that in the protein mixture, ovalbumin has a major influence on the CaCO3 formation through a strong interaction with calcium ions, which leads to the coalescence and creation of a steric barrier reducing particle growth. The authors proposed a mechanism of calcium carbonate grain growth in the presence of both proteins, taking into account the interaction of calcium ions with the protein. PMID:28774065

The oxidation products of crude mesobilirubinogen

PubMed Central

Stoll, M. S.; Gray, C. H.

1970-01-01

Bile pigment esters were separated by ascending t.l.c. Apparently pure pigments, obtained by ferric chloride oxidation of crude mesobilirubinogen, derived from commercial bilirubin by reduction with sodium amalgam, were shown to be complex mixtures. Successive chromatography of their dimethyl esters on silica gel in methyl acetate–methyl propionate–dichloromethane–carbon tetrachloride (1:1:1:1, by vol.), ethyl methyl ketone–1,2-dichloroethane (1:2, v/v) and benzene–ethanol (100:3, v/v) revealed two major blue pigments (verdins), six major violet pigments (violins) and a red pigment (rhodin) together with numerous minor components. i-Urobilin dimethyl ester, prepared from mesobilirubinogen by dehydrogenation with aqueous iodine, was resolved into three major and at least four minor components on silica gel–kieselguhr (3:1, w/w) in benzene–ethanol (25:2, v/v). The chemical nature of these pigments was investigated by oxidation, by visible and u.v. spectroscopy, by mass spectrometry and by n.m.r. spectrometry. The evidence suggests unusual rearrangement of bilirubin during reduction leading to the formation of IIIα and XIIIα isomers. Isomeric forms of mesobiliviolin IXα and of i-urobilin IXα may also be formed. PMID:5420035

Catalytic ozonation of dimethyl phthalate and chlorination disinfection by-product precursors over Ru/AC.

PubMed

Wang, Jianbing; Zhou, Yunrui; Zhu, Wanpeng; He, Xuwen

2009-07-15

Catalytic ozonation of dimethyl phthalate (DMP) in aqueous solution (5mg/L) under various reactions was performed to examine the effect of catalyst dosage, catalyst particle size, ozone dosage, and gas flow rate on the mineralization of DMP. The mineralization of DMP can be achieved via ozonation and the presence of Ru/AC could greatly accelerate the mineralization rate of DMP in ozonation process. In the continuous experiment of the Ru/AC catalyzed ozonation of DMP, total organic carbon (TOC) removals were kept stable around 75% during 42 h reaction. No leaching of ruthenium was observed in the treated water samples. The treatment of natural water using Ru/AC+O(3), Ru/AC+O(2) and ozonation alone was studied. In the Ru/AC+O(3) process, TOC removals, the reductions of the haloacetic acid formation potentials (HAAFPs), and the reductions of the trihalomethane formation potentials (THMFPs) of 11 water samples were 22-44%, 39-61% and 50-65%, respectively. Ru/AC+O(3) process was much more effective than ozonation alone for TOC removal and the reduction of disinfection by-product formation potential (DBPFP) in the treatment of natural water. It is a promising water treatment technology.

Emissions of sulfur gases from wetlands

NASA Technical Reports Server (NTRS)

Hines, Mark E.

1992-01-01

Data on the emissions of sulfur gases from marine and freshwater wetlands are summarized with respect to wetland vegetation type and possible formation mechanisms. The current data base is largest for salt marshes inhabited by Spartina alterniflora. Both dimethyl sulfide (DMS) and hydrogen sulfide (H2S) dominate emissions from salt marshes, with lesser quantities of methyl mercaptan (MeSH), carbonyl sulfide (COS), carbon disulfide (CS2) and dimethyl disulfide (DMDS) being emitted. High emission rates of DMS are associated with vegetation that produces the DMS precursor dimethylsulfonionpropionate (DMSP). Although large quantities of H2S are produced in marshes, only a small percentage escapes to the atmosphere. High latitude marshes emit less sulfur gases than temperate ones, but DMS still dominates. Mangrove-inhabited wetlands also emit less sulfur than temperate S. alterniflora marshes. Few data are available on sulfur gas emissions from freshwater wetlands. In most instances, sulfur emissions from temperate freshwater sites are low. However, some temperate and subtropical freshwater sites are similar in magnitude to those from marine wetlands which do not contain vegetation that produces DMSP. Emissions are low in Alaskan tundra but may be considerably higher in some bogs and fens.

Pressure-induced amorphization and reactivity of solid dimethyl acetylene probed by in situ FTIR and Raman spectroscopy

NASA Astrophysics Data System (ADS)

Guan, Jiwen; Daljeet, Roshan; Kieran, Arielle; Song, Yang

2018-06-01

Conjugated polymers are prominent semiconductors that have unique electric conductivity and photoluminescence. Synthesis of conjugated polymers under high pressure is extremely appealing because it does not require a catalyst or solvent used in conventional chemical methods. Transformation of acetylene and many of its derivatives to conjugated polymers using high pressure has been successfully achieved, but not with dimethyl acetylene (DMA). In this work, we present a high-pressure study on solid DMA using a diamond anvil cell up to 24.4 GPa at room temperature characterized by in situ Fourier transform infrared and Raman spectroscopy. Our results show that solid DMA exists in a phase II crystal structure and is stable up to 12 GPa. Above this pressure, amorphization was initiated and the process was completed at 24.4 GPa. The expected polymeric transformation was not evident upon compression, but only observed upon decompression from a threshold compression pressure (e.g. 14.4 GPa). In situ florescence measurements suggest excimer formation via crystal defects, which induces the chemical reactions. The vibrational spectral analysis suggests the products contain the amorphous poly(DMA) and possibly additional amorphous hydrogenated carbon material.