Effect of Hydrazines on Substrate Utilization by a Strain of Enterobacter Cloacae

DTIC Science & Technology

1983-01-01

UDMH) to a strain of soil bacteria to be comparable to that observed in other biological systems. A subsequent study by MANTEL & LONDON (1980) suggested...metabolites derived from lysed cells were being metabolized . This observation in conjunction with reports on the effects of Hz intoxication on...carbohydrate metabolism (UNDERHILL & HOGAN 1915, IZUME & LEWIS 1926-1927, SMITH 1965, TAYLOR 1966, GEORGE & BACK 1977) prompted an investigation of the effects

Material Capability for Transport of Unsymmetrical Dimethylhydrazine

DTIC Science & Technology

1990-07-13

is shown in Figure 1. The air supply was house compressed air conditioned by passing it through a series of demisters, a hot Hopcalite catalyst bed...required to reach that value was recorded. At the end of a test, the tubing was rinsed with methanol and dried with compressed breathing air or filtered... compressed house air . Solvents such as acetone were not used as they react with hydrazines (8]. Table 2 lists the combinations of tubing length, UDMH or

Role of Chlorine Dioxide in N-Nitrosodimethylamine Formation from Oxidation of Model Amines.

PubMed

Gan, Wenhui; Bond, Tom; Yang, Xin; Westerhoff, Paul

2015-10-06

N-Nitrosodimethylamine (NDMA) is an emerging disinfection byproduct, and we show that use of chlorine dioxide (ClO2) has the potential to increase NDMA formation in waters containing precursors with hydrazine moieties. NDMA formation was measured after oxidation of 13 amines by monochloramine and ClO2 and pretreatment with ClO2 followed by postmonochloramination. Daminozide, a plant growth regulator, was found to yield 5.01 ± 0.96% NDMA upon reaction with ClO2, although no NDMA was recorded during chloramination. The reaction rate was estimated to be ∼0.0085 s(-1), and on the basis of our identification by mass spectrometry of the intermediates, the reaction likely proceeds via the hydrolytic release of unsymmetrical dimethylhydrazine (UDMH), with the hydrazine structure a key intermediate in NDMA formation. The presence of UDMH was confirmed by gas chromatography-mass spectrometry analysis. For 10 of the 13 compounds, ClO2 preoxidation reduced NDMA yields compared with monochloramination alone, which is explained by our measured release of dimethylamine. This work shows potential preoxidation strategies to control NDMA formation may not impact all organic precursors uniformly, so differences might be source specific depending upon the occurrence of different precursors in source waters. For example, daminozide is a plant regulator, so drinking water that is heavily influenced by upstream agricultural runoff could be at risk.

BLAKE - A Thermodynamics Code Based on TIGER: Users’ Guide and Manual

DTIC Science & Technology

1982-07-01

hydrazine UDMH Water H20 3S I The formulas and enthalpies of formation of these ingredients are listed in Appendix B. Wherever possible they were taken...estimates for B(T), it does not improve the estimates of C(I). Numerically the contribution of the third coefficient is necessary- for loading densities ...here, C will be assumed independent of temperature. The vejume, V, is related to the reference mass, Mo, and the density , p, by P = M /V (9) 0 The

A Summary of NASA and USAF Hypergolic Propellant Related Spills And Fires

NASA Technical Reports Server (NTRS)

Nufer, B. M.

2009-01-01

Hypergolic fluids are toxic liquids that react spontaneously and violently when they contact each other. These fluids are used in many different rocket and aircraft systems for propulsion and hydraulic power including, orbiting satellites, manned spacecraft, military aircraft, and deep space probes. Hypergolic fuels include hydrazine (N 2H4) and its derivatives including monomethylhydrazine (MMH), unsymmetrical di-methylhydrazine (UDMH), and Aerozine 50 (A-50), which is an equal mixture of N2H4 and UDMH. The oxidizer used with these fuels is usually nitrogen tetroxide (N2O4), also known as di-nitrogen tetroxide or NTO, and various blends of N2O4 with nitric oxide (NO). Several documented, unintentional hypergolic fluid spills and fires related to the Apollo Program, the Space Shuttle Program, and several other programs from approximately 1968 through the spring of 2009 have been studied for the primary purpose of extracting the lessons learned. Spill sites include KSC, JSC, WSTF, CCAFS, EAFB, McConnell AFB, and VAFB.

Proceedings of the Conference on the Environmental Chemistry of Hydrazine Fuels (3rd) Held in Panama City Beach, Florida on 15-17 September 1987

DTIC Science & Technology

1988-01-01

for hydrauine, MMH and UDMH are 4.78 x 10-6, 10.2 x 10Ś, and 3.19 x 10-6 aecŕ, respectively. Plots of the log(area) versus time were linear and...followed first-order kinetics except for hydrauine, for which a non- linear portion was observed in the first 6 to 8 hours. This portion of the decay...As a result, the prototype flow reactor can be represented to good approximation by a linear combination of point source solutions (Reference 19). The

40 CFR Table 2 to Subpart Jj of... - List of Volatile Hazardous Air Pollutants

Code of Federal Regulations, 2014 CFR

2014-07-01

...-Dichloropropene 542756 Diethanolamine 111422 N,N-Dimethylaniline 121697 Diethyl sulfate 64675 3,3... 79447 N,N-Dimethylformamide 68122 1,1-Dimethylhydrazine 57147 Dimethyl phthalate 131113 Dimethyl sulfate... Hexamethylphosphoramide 680319 Hexane 110543 Hydrazine 302012 Hydroquinone 123319 Isophorone 78591 Maleic anhydride 108316...

40 CFR Table 2 to Subpart Jj of... - List of Volatile Hazardous Air Pollutants

Code of Federal Regulations, 2013 CFR

2013-07-01

...-Dichloropropene 542756 Diethanolamine 111422 N,N-Dimethylaniline 121697 Diethyl sulfate 64675 3,3... 79447 N,N-Dimethylformamide 68122 1,1-Dimethylhydrazine 57147 Dimethyl phthalate 131113 Dimethyl sulfate... Hexamethylphosphoramide 680319 Hexane 110543 Hydrazine 302012 Hydroquinone 123319 Isophorone 78591 Maleic anhydride 108316...

40 CFR Table 2 to Subpart Jj of... - List of Volatile Hazardous Air Pollutants

Code of Federal Regulations, 2012 CFR

2012-07-01

...-Dichloropropene 542756 Diethanolamine 111422 N,N-Dimethylaniline 121697 Diethyl sulfate 64675 3,3... 79447 N,N-Dimethylformamide 68122 1,1-Dimethylhydrazine 57147 Dimethyl phthalate 131113 Dimethyl sulfate... Hexamethylphosphoramide 680319 Hexane 110543 Hydrazine 302012 Hydroquinone 123319 Isophorone 78591 Maleic anhydride 108316...

Occupational hazards of missile operations with special regard to the hydrazine propellants.

PubMed

Back, K C; Carter, V L; Thomas, A A

1978-04-01

The second generation of ballistic missiles and boosters, characterized by increased range and quick reaction capability, required the development of new high-energy storage propellants. This exploration led to the introduction of hydrazine (Hz), monomethylhydrazine (MMH), and 1,1-dimethylhydrazine (UDMH) into the USAF inventory. These compounds are all storable, noncryogenic, high-energy fuels which may be used alone or in combination as mixed amine fuels. Early toxicology experiments were to produce data on acute and subacute effects of the propellants in order to set standards for test and operational procedures to protect propellant handlers. The early work indicated that, despite similar chemical characteristics, there were marked differences between the compounds in terms of toxicological mechanisms. Since the propellant systems have been used for some 15 years, recent emphasis on toxicology has been centered on the more chronic effects and on an increasing body of evidence from animal experiments that the compounds may possess oncogenic potential as well as chronic systemic effects. This paper addresses itself to data leading up to current occupational standards.

Investigation of critical burning of fuel droplets

NASA Technical Reports Server (NTRS)

Allison, C. B.; Canada, G. S.; Faeth, G. M.

1972-01-01

Measurements were made on the burning of liquid hydrazine, MMH, and UDMH in a combustion gas environment. The experimental range of these tests involved gas temperatures of 1660-2530 K, oxygen concentrations of 0-42% by mass and droplet diameters (employing both droplets and porous spheres) of 0.11-1.91 cm. at atmospheric pressure. A simplified hybrid combustion theory was developed which was found to correlate the present results as well as the experimental measurements of other investigators. Measurements were also made of the monopropellant strand burning rates and liquid surface temperatures of a number of nitrate ester fuels and hydrazine at elevated pressures. The temperature measurements for the nitrate esters were found to be in good agreement with a theoretical model which allowed for gas solubility in the liquid phase at high pressures. Experimental results were also obtained on the burning rates and liquid surface temperatures of a number of paraffin and alcohol fuels burning in air pressures up to 72 atm. For these tests, the fuels were burned from porous spheres in a natural convection environment. Initial findings on a pressurized flat flame burner are also described as well as the design of an oscillatory combustion apparatus to test the response of burning liquid fuels.

Electrostatic Evaluation of the Propellant Handlers Ensemble

NASA Technical Reports Server (NTRS)

Hogue, Michael D.; Calle, Carlos I.; Buhler, Charles

2006-01-01

The Self-Contained Atmospheric Protective Ensemble (SCAPE) used in propellant handling at NASA's Kennedy Space Center (KSC) has recently completed a series of tests to determine its electrostatic properties of the coverall fabric used in the Propellant Handlers Ensemble (PHE). Understanding these electrostatic properties are fundamental to ensuring safe operations when working with flammable rocket propellants such as hydrazine, methyl hydrazine, and unsymmetrical dimethyl hydrazine. These tests include surface resistivity, charge decay, triboelectric charging, and flame incendivity. In this presentation, we will discuss the results of these tests on the current PHE as well as new fabrics and materials being evaluated for the next generation of PHE.

Vandenberg Air Force Base Emission Survey.

DTIC Science & Technology

1983-01-01

1,020 gals) b. SLC-3 Hydrazine Scrubber c. SLC-4 1) West Pad - Two Aerozine-50 Tanks (11,000 gals each) (one emission point) - Unsymmetrical Dimethyl...Launch Complex (SLC)-2 1) Aerozine-50 Tank (880 gal) 2) Nitrogen Tetroxide Tank (1,020 gal) b. SLC-3 Hydrazine Scrubber c. SLC-4 1) West Pad - Two...vapors are put through a scrubber to reduce the amount of fuel vapor entering the atmosphere. Likewise, specific Oxidizer vapors are disposed of by a

Theory investigation progress of DMAZ

NASA Astrophysics Data System (ADS)

Xie, Hui; Mu, Xiaogang; Zhang, Yue; Wang, Xuanjun

2017-05-01

The recent progress in the theoretical study of N, N-dimethyl-2-azidoethylamine (DMAZ), a new type of azide fuel, is summarized. Thermodynamic Properties (such as Enthalpy-of-Formation, Enthalpy-of-Vaporization, and Enthalpy-of-Sublimation), conformers, Spectrums, the Henry's constant, ignition delay et al. are studied by Density Functional Theory (DFT). It is proved that DMAZ has good performance with a density impulse 2.499 Ns/m3, and has a good application prospect in replacing the traditional hydrazine propellant methyl-hydrazine (MMH).

Synthesis of unsymmetrical dimethylhydrazine oxalate from rejected liquid rocket propellant

NASA Astrophysics Data System (ADS)

Mu, Xiaogang; Yang, Jingjing; Zhang, Youzhi

2018-02-01

The rejected liquid propellant unsymmetrical dimethylhydrazine (UDMH) was converted to UDMH oxalate, which has commercial value. The UDMH oxalate structure and stability were investigated by the Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, differential scanning calorimetry, and ultraviolet-visible spectrophotometric analysis. The results indicate that UDMH oxalate has good thermal and aqueous solution stability, a melting point of 144 °C, an initial decomposition temperature of 180 °C, and a peak wavelength of UV in aqueous solution at λ = 204 nm. This disposal method of rejected UDMH is highly efficient and environmentally safe.

Development of an Automated Reader for Analysis and Storage of Personnel Dosimeter Badge Data

NASA Technical Reports Server (NTRS)

Meneghelli, B. J.; Hodge, T. R.; Robinson, L. J.; Lueck, D. E.

1997-01-01

The collection and archiving of data from personnel dosimeters has become increasingly important in light of the lowered Threshold Limit Values (TLV) for HydraZine (HZ), MonoMethylHydrazine (MMH), and Unsymmetrical DiMethylHydrazine (UDMH). The American Conference of Government Industrial Hygienists (ACGIH) lowered the TLV from 100 parts per billion (ppb) to IO ppb and has caused increased concern over long term exposures of personnel to trace levels of these hypergols and other potentially harmful chemicals. An automated system of reading the exposure levels of personnel dosimeters and storing exposure data for subsequent evaluation has been developed. The reading of personnel dosimeter badges for exposure to potentially harmful vapor concentrations of hydrazines or other chemicals is performed visually by comparing the color developed by the badge with a calibrated color comparator. The result obtained using visual comparisons of the developed badge color with the comparator may vary widely from user to user. The automated badge reader takes the variability out of the dosimeter reading by accurately comparing the reflectance obtained from a colored spot on the badge with a reading on the same spot prior to any exposure to chemical vapors. The observed difference between the reflectance values is used as part of a calculation of the dose value for the badge based on a stored calibration curve. The badge reader also stores bar-code data unique to each badge, as well as bar-code information on the user, as part of the permanent badge record. The start and stop exposure times for each badge are recorded and can be used as part of the calculated concentration, in ppm, for each badge logged during a recording period. The badge reader is equipped with a number of badge holders, each of which is unique to a specific type of personnel dosimeter badge. This gives the reader maximum flexibility to allow for the reading of several different types of badges. Test results of the badge reader for several different types of personnel dosimeter badges are presented within the body of this paper.

Decontamination of unsymmetrical dimethylhydrazine waste water by hydrodynamic cavitation-induced advanced Fenton process.

PubMed

Torabi Angaji, Mahmood; Ghiaee, Reza

2015-03-01

A pilot scale hydrodynamic cavitation (HC) reactor, using iron metal blades, as the heterogeneous catalyst, with no external source of H₂O₂ was developed for catalytic decontamination of unsymmetrical dimethylhydrazine (UDMH) waste water. In situ generation of Fenton reagents suggested an induced advanced Fenton process (IAFP) to explain the enhancing effect of the used catalyst in the HC process. The effects of the applied catalyst, pH of the initial solution (1.0-9.7), initial UDMH concentration (2-15 mg/l), inlet pressure (5.5-7.8bar), and downstream pressure (2-6 bar), have been investigated. The results showed that the highest cavitation yield can be obtained at pH 3 and initial UDMH concentration of 10mg/l. Also, an increase in the inlet pressure would lead to an increase in the extent of UDMH degradation. In addition, the optimum value of 3 bar was determined for the downstream pressure that resulted to 98.6% degradation of UDMH after 120 min of processing time. Neither n-nitrosodimethylamine (NDMA) nor any other toxic byproduct (/end-product) was observed in the investigated samples. Formic acid and acetic acid, as well as nitromethane, were identified as oxidation by-products. The present work has conclusively established that hydrodynamic cavitation in combination with Fenton's chemistry can be effectively used for the degradation of UDMH. Copyright © 2014 Elsevier B.V. All rights reserved.

40 CFR 721.10594 - Hexanedioic acid, polymer with 2,2-dimethyl-1,3-propanediol, 1,6-hexanediol, hydrazine, 3-hydroxy...

Code of Federal Regulations, 2013 CFR

2013-07-01

... SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10594...) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...-173; CAS No. 1138156-39-4) is subject to reporting under this section for the significant new uses...

40 CFR 721.10594 - Hexanedioic acid, polymer with 2,2-dimethyl-1,3-propanediol, 1,6-hexanediol, hydrazine, 3-hydroxy...

Code of Federal Regulations, 2014 CFR

2014-07-01

... SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10594...) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as...-173; CAS No. 1138156-39-4) is subject to reporting under this section for the significant new uses...

Soil factors of ecosystems' disturbance risk reduction under the impact of rocket fuel

NASA Astrophysics Data System (ADS)

Krechetov, Pavel; Koroleva, Tatyana; Sharapova, Anna; Chernitsova, Olga

2016-04-01

Environmental impacts occur at all stages of space rocket launch. One of the most dangerous consequences of a missile launch is pollution by components of rocket fuels ((unsymmetrical dimethylhydrazine (UDMH)). The areas subjected to falls of the used stages of carrier rockets launched from the Baikonur cosmodrome occupy thousands of square kilometers of different natural landscapes: from dry steppes of Kazakhstan to the taiga of West Siberia and mountains of the Altai-Sayany region. The study aims at assessing the environmental risk of adverse effects of rocket fuel on the soil. Experimental studies have been performed on soil and rock samples with specified parameters of the material composition. The effect of organic matter, acid-base properties, particle size distribution, and mineralogy on the decrease in the concentration of UDMH in equilibrium solutions has been studied. It has been found that the soil factors are arranged in the following series according to the effect on UDMH mobility: acid-base properties > organic matter content >clay fraction mineralogy > particle size distribution. The estimation of the rate of self-purification of contaminated soil is carried out. Experimental study of the behavior of UDMH in soil allowed to define a model for calculating critical loads of UDMH in terrestrial ecosystems.

Aerojet - AJ10-137 Apollo Service Module Engine. Chapter 5, Appendix G

NASA Technical Reports Server (NTRS)

Boyce, Clay

2009-01-01

The general configuration of the SPS engine was 20,000 pounds of thrust, with a chamber pressure of 100 psi and specific impulse (Isp) of 314.5. The very large nozzle had an area ratio of 62.5:1 (exit area to throat area). The propellants were nitrogen tetroxide (also known as N2O4 and nitrous oxide) and A-50. A-50 was a hydrazine family fuel. Aerojet developed it for the Titan Missile Program when they went with Titan II, to store it in the launch silos. They wanted the highest performance they could get. N2H4 was just pure hydrazine, which doesn't take low temperature very well. In fact, it freezes about like water. We started adding unsymmetrical-dimethylhydrazine (UDMH) to the hydrazine until such time as it would meet the environmental specifications the Air Force needed for Titan II. It turned out it s roughly a fifty-fifty mix. We still had to be careful with that fuel because the two fluids didn't mix very well chemically. We had to spray the two fluids through some special nozzles to get them to emulsify with each other into a single fluid. If we ever got it too cold or froze it, the hydrazine separated back out. Then, if we tried to run the engine, things could go boom in the night. The inlet pressure was only 165 pounds per square inch absolute (psia), but we needed at least forty psi pressure drop across the injector just to get some kind of stable flow. It was a whole new game for some of us. We didn't have much supply pressure to work with. It had the aluminum injector to keep the weight down. That was a couple feet in diameter, and we didn't have a lot of propellant to cool it. In fact, we had to use both propellants to keep the injector cool. There were twenty-two ring channels in the injector. Specification required 750 seconds duration, or fifty engine restarts during a flight. There were several first flight things we accomplished with the engine. It was the first ablative thrust chamber of any size to fly. (See Slide 6, Appendix G) There were no liners in it. It was just straight ablative material. It took us a while to figure that out. It was a throat-gimbaled engine, and it was the first engine to fly with columbium (also known as niobium, used as an alloying element in steels and superalloys) in the nozzle.

Toxic Hazards Research Unit Annual Technical Report: 1979

DTIC Science & Technology

1979-08-01

in hemangiosarcomas and Kupffer cell sarcomas. In the 5 ppm UDMH exposure group, there were 19 hemangiosarcomas versus 3 in unexposed controls. Also...responsible for the incidence of liver hemangiosarcomas . The objective of this study was to determine the oncogenic potential of purified UDMH (DMNA... Hemangiosarcoma 0 25 Cholangiocarcinoma 0 10 Hepatocellular Adenoma 0 1 Small Intestinal Papilloma 1 0 Colonic Papilloma 0 8 Malignant Neoplasm

Novel pyrazolyl-s-triazine derivatives, molecular structure and antimicrobial activity

NASA Astrophysics Data System (ADS)

Sharma, Anamika; Ghabbour, Hazem; Khan, Shams Tabrez; de la Torre, Beatriz G.; Albericio, Fernando; El-Faham, Ayman

2017-10-01

A new series of pyrazole-containing s-triazine derivatives were synthesized by reaction of the corresponding s-triazinyl hydrazine derivatives with acetylacetone in the presence of HClO4 or DMF/TEA. The former method allowed the preparation of the target products with higher yields. All compounds were fully characterized. X-ray single crystal diffraction for two representative compounds (4-(4,6-bis(3,5-dimethyl-1H-pyrazol-1-yl)-1,3,5-triazin-2-yl)morpholine and N-benzyl-4-(3,5-dimethyl-1H-pyrazol-1-yl)-6-(piperidin-1-yl)-1,3,5-triazin-2-amine) was studied and the molecular structures were optimized using the DFT/B3LYP method. The structures were found to be in agreement with X-ray structures. The antimicrobial and antifungal activity of the prepared compounds were tested against the growth of several microorganisms.

Toxic Hazards Research Unit Annual Technical Report: 1976

DTIC Science & Technology

1976-09-01

1miiethylliydrazine ( UDMH ) 46 Toxicity of Solid Rocket Motor Exchiange - Effects of HCI, HF and Alumina on Rodents 53 Toxicity of High Density jet... Formula C12H20 C14 H20 C714 Molecular Weight 164 188 98 Boiling Point (OF) 431 522 213 Vapor Pressure (70 F) 0.354 mm Hg 0.025 mm Hg 42 mm Hg Density ...Inhalation Exposure of Animals to Coal Tar Aerosol 20 A Six-Month Chronic Inhalation Exposure of Animals to UDMH to Determine Its Oncogenic Capacity

Evaporation Rate Study and NDMA Formation from UDMH/NO2 Reaction Products

NASA Technical Reports Server (NTRS)

Buchanan, Vanessa D.; Dee, Louis A.; Baker, David L.

2003-01-01

Laboratory samples of uns-dimethylhydrazine (UDMH) fuel/oxidizer (nitrogen dioxide) non-combustion reaction products (UFORP) were prepared using a unique permeation tube technology. Also, a synthetic UFORP was prepared from UDMH, N-nitrosodimethylamine (NDMA), dimethylammonium nitrate, sodium nitrite and purified water. The evaporation rate of UFORP and synthetic UFORP was determined under space vacuum (approx 10(exp -3) Torr) at -40 ?C and 0 ?C. The material remaining was analyzed and showed that the UFORP weight and NDMA concentration decreased over time; however, NDMA had not completely evaporated. Over 85% of the weight was removed by subjecting the UFORP to 10(-3) Torr for 7 hours at -40 ?C and 4 hours at 0 ?C. A mixture of dimethylammonium nitrate and sodium nitrite formed NDMA at a rapid rate in a moist air environment. A sample of UFORP residue was analyzed for formation of NDMA under various conditions. It was found that NDMA was not formed unless nitrite was added.

Molecular structure, NMR, UV-Visible, vibrational spectroscopic and HOMO, LUMO analysis of (E)-1-(2, 6-bis (4-methoxyphenyl)-3, 3-dimethylpiperidine-4-ylidene)-2-(3-(3, 5-dimethyl-1H-pyrazol-1-yl) pyrazin-2-yl) hydrazine by DFT method

NASA Astrophysics Data System (ADS)

Alphonsa, A. Therasa; Loganathan, C.; Anand, S. Athavan Alias; Kabilan, S.

2016-02-01

We have synthesized (E)-1-(2, 6-bis (4-methoxyphenyl)-3, 3-dimethylpiperidine-4-ylidene)-2-(3-(3, 5-dimethyl-1H-pyrazol-1-yl) pyrazin-2-yl) hydrazine (PM6). It was characterized using FT-IR, FT-Raman, 1H NMR, 13C NMR techniques. To interpret the experimental data, ab initio computations of the vibrational frequencies were carried out using the Gaussian 09 program followed by the full optimizations done using Density Functional Theory (DFT) at B3LYP/6-311 G(d,p) level. The combined use of experiments and computations allowed a firm assignment of the majority of observed bands for the compound. The calculated stretching frequencies have been found to be in good agreement with the experimental frequencies. The electronic and charge transfer properties have been explained on the basis of highest occupied molecular orbitals (HOMOs), lowest unoccupied molecular orbitals (LUMOs) and density of states (DOS). The absorption spectra have been computed by using time dependent density functional theory (TD-DFT). 1H and 13C NMR spectra were recorded and 1H and 13C NMR chemical shifts of the molecule were calculated using the gauge independent atomic orbital (GIAO) method. From the optimized geometry of the molecule, molecular electrostatic potential (MEP) distribution, frontier molecular orbitals (FMOs) of the title compound have been calculated in the ground state theoretically. The theoretical results showed good agreement with the experimental values.

Ozone depletion caused by NO and H2O emissions from hydrazine-fueled rockets

NASA Astrophysics Data System (ADS)

Ross, M. N.; Danilin, M. Y.; Weisenstein, D. K.; Ko, M. K. W.

2004-11-01

Rockets using unsymmetrical dimethyl hydrazine (N(CH3)2NH2) and dinitrogen tetroxide (N2O4) propellants account for about one third of all stratospheric rocket engine emissions, comparable to the solid-fueled rocket emissions. We use plume and global atmosphere models to provide the first estimate of the local and global ozone depletion caused by NO and H2O emissions from the Proton rocket, the largest hydrazine-fueled launcher in use. NO and H2O emission indices are assumed to be 20 and 350 g/kg (propellant), respectively. Predicted maximum ozone loss in the plume of the Proton rocket is 21% at 44 km altitude. Plume ozone loss at 20 km equals 8% just after launch and steadily declines to 2% by model sunset. Predicted steady state global ozone loss from ten Proton launches annually is 1.2 × 10-4%, with nearly all of the loss due to the NO component of the emission. Normalized by stratospheric propellant consumption, the global ozone depletion efficiency of the Proton is approximately 66-90 times less than that of solid-fueled rockets. In situ Proton plume measurements are required to validate assumed emission indices and to assess the role of rocket emissions not considered in these calculations. Such future studies would help to establish a formalism to evaluate the relative ozone depletion caused by different rocket engines using different propellants.

Dihydropyrimidine based hydrazine dihydrochloride derivatives as potent urease inhibitors.

PubMed

Khan, Ajmal; Hashim, Jamshed; Arshad, Nuzhat; Khan, Ijaz; Siddiqui, Naureen; Wadood, Abdul; Ali, Muzaffar; Arshad, Fiza; Khan, Khalid Mohammed; Choudhary, M Iqbal

2016-02-01

Four series of heterocyclic compounds 4-dihydropyrimidine-2-thiones 7-12 (series A), N,S-dimethyl-dihydropyrimidines 13-18 (series B), hydrazine derivatives of dihydropyrimidine 19-24 (series C), and tetrazolo dihydropyrimidine derivatives 25-30 (series D), were synthesized and evaluated for in vitro urease inhibitory activity. The series B-D were first time examined for urease inhibition. Series A and C were found to be significantly active with IC50 values between 34.7-42.9 and 15.0-26.0 μM, respectively. The structure-activity relationship showed that the free S atom and hydrazine moiety are the key pharmacophores against urease enzyme. The kinetic studies of the active series A (7-12) and C (19-24) were carried out to determine their modes of inhibition and dissociation constants Ki. Compounds of series A (7-12) and series C (19-24) showed a mixed-type of inhibition with Ki values ranging between 15.76-25.66 and 14.63-29.42 μM, respectively. The molecular docking results showed that all the active compounds of both series have significant binding interactions with the active sites specially Ni-ion of the urease enzyme. Cytotoxicity of all series A-D was also evaluated against mammalian mouse fibroblast 3T3 cell lines, and no toxicity was observed in cellular model. Copyright © 2016 Elsevier Inc. All rights reserved.

Sambar, an Indian Dish Prevents the Development of Dimethyl Hydrazine–Induced Colon Cancer: A Preclinical Study

PubMed Central

Prasad, Vutturu Ganga; Reddy, Neetinkumar; Francis, Albi; Nayak, Pawan G.; Kishore, Anoop; Nandakumar, Krishnadas; Rao, Mallikarjuna C.; Shenoy, Rekha

2016-01-01

Background: Colon cancer (CC) is the third commonly diagnosed cancer and the second leading cause of mortality in the US when compared to India where prevalence is less. Possible reason could be the vegetarian diet comprising spices used in curry powders. Researchers believe that 70% of the cases are associated with diet. Spices have inherited a rich tradition for their flavor and medicinal properties. Researchers have been oriented towards spices present in food items for their antitumorigenic properties. Objective: We investigated the effects of sambar as a preventive measure for 1,2-dimethyl hydrazine (DMH)-induced CC in Wistar albino rats. Materials and Methods: The animals were divided into three groups (n = 6) namely control, DMH, and sambar. At the end of the experimental period, the animals were killed using anesthesia and the colons and livers were examined. Results: All the treatment groups exhibited a significant change in the number of aberrant crypt foci (ACF). Sambar group showed a significant change in the colonic GSH when compared to both normal and DMH groups. A significant reduction in the liver GSH was noted in the sambar group. Only sambar group showed a significant change in the liver catalase levels when compared to DMH. There was a significant reduction in the colonic nitrite in the sambar-treated group; 2.94 ± 0.29 when compared to DMH control at 8.09 ± 1.32. On the contrary, a significant rise in the liver nitrite levels was observed in the sambar-treated rats. Conclusion: Sambar may prevent the risk of CC when consumed in dietary proportions. SUMMARY Consumption of sambar significantly reduced aberrant crypt foci in DMH-induced colon cancer modelSambar treatment prevented DMH-induced oxidative changes in the colonic tissue, indicating its antioxidant roleSambar comprises a variety of spices that exhibited both pro- and antioxidant properties in different tissues, leading to its overall beneficial effect in this model. Abbreviations used: ACF: aberrant crypt foci, CC: colon cancer, DMH: 1,2-dimethyl hydrazine, GSH: glutathione, IL-6: Interleukin-6, TNF-α: Tumor necrosis factor-alpha. PMID:27761072

Thrust Evaluation of an Arcjet Thruster Using Dimethyl Ether as a Propellant

NASA Astrophysics Data System (ADS)

Kakami, Akira; Beppu, Shinji; Maiguma, Muneyuki; Tachibana, Takeshi

This paper describes the performance of an arcjet thruster using dimethyl ether (DME) as a propellant. DME, an ether compound, has adequate characteristics for space propulsion systems; DME is storable in a liquid state without a high pressure or cryogenic device and requires no sophisticated temperature management. DME is gasified and liquefied simply by adjusting temperature, whereas hydrazine, a conventional propellant, requires an iridium-based particulate catalyst for its gasification. In this study, thrust of the designed kW-class DME arcjet thruster is measured with a torsional thrust stand. Thrust measurements show that thrust is increased with propellant mass flow rate, and that thrust using DME propellant is higher than when using nitrogen. The prototype DME arcjet thruster yields a specific impulse of 330 s, a thruster efficiency of 0.14, and a thrust of 0.19 N at 60-mg/s DME mass flow rate at 25-A discharge current. The corresponding discharge power and specific power are 2.3 kW and 39 MJ/kg.

Indicators for the optical measurement of sulphur dioxide gas

NASA Astrophysics Data System (ADS)

Sharma, Ashutosh; Ali, Zulfiqur; McStay, Daniel

1992-05-01

A number of fluorophores were investigated for their suitability to be employed as indicators in SO2 measurement. Several indicators, including PAll's, 5(and 6) carboxy-4'-5'-dimethyl fluorescein, new fuschin, hydrazine hydrochloride and chioropyridine hydrochloride, showed decrease in the fluorescence intensity with increase in SO2 concentration. Fluorescence quenching of benzopurpurin by 502 is found to be extremely efficient, with a little or no interference from the other toxic gases NH3 and H2S. These results are analyzed using Stem-Volmer relation. The fmding is considered to be of potential utility for the development of an improved fibre optic SO2 sensor/probe.

Development of an Automated Reader for Analysis and Storage of Personnel Dosimeter Badge Data

NASA Technical Reports Server (NTRS)

Meneghelli, B. J.; Hodge, T. R.; Robinson, L. J.; Lueck, D. E.

1997-01-01

The collection and archiving of data from personnel dosimeters has become increasingly important in light of the lowered threshold limit values (TLV) for hydrazine (HZ), monomethylhydrazine (MMH), and unsymmetrical dimethylhydrazine (UDMH). The American Conference of Government Industrial Hygienists (ACGIH) lowered the TLV from 100 parts per billion (ppb) to 10 ppb and has caused increased concern over long term exposures of personnel to trace levels of these hypergols and other potentially harmful chemicals. An automated system of reading the exposure levels of personnel dosimeters and storing exposure data for subsequent evaluation has been developed. The reading of personnel dosimeter badges for exposure lo potentially harmful vapor concentrations of hydrazines or other chemicals is performed visually by comparing the color developed by the badge with a calibrated color comparator. The result obtained using visual comparisons of the developed badge color with the comparator may vary widely from user to user. The automated badge reader takes the variability out of the dosimeter reading by accurately comparing the reflectance obtained from a colored spot on the badge with a reading on the same spot prior to any exposure to chemical vapors. The observed difference between the reflectance values is used as part of a calculation of the dose value for the badge based on a stored calibration curve. The badge reader also stores bar-code data unique to each badge, as well as bar-code information on the user, as part of the permanent badge record. The start and stop exposure times for each badge are recorded and can be used as part of the calculated concentration, in ppm, for each badge logged during a recording period. The badge reader is equipped with a number of badge holders, each of which is unique to a specific type of personnel dosimeter badge. This gives the reader maximum flexibility to allow for the reading of several different types of badges. Test results of the badge reader for several different types of personnel dosimeter badges are presented within the body of this paper.

Dual-Functional Hydrazide-Reactive and Anhydride-Containing Oligomeric Hydrogel Building Blocks.

PubMed

Kascholke, Christian; Loth, Tina; Kohn-Polster, Caroline; Möller, Stephanie; Bellstedt, Peter; Schulz-Siegmund, Michaela; Schnabelrauch, Matthias; Hacker, Michael C

2017-03-13

Biomimetic hydrogels are advanced biomaterials that have been developed following different synthetic routes. Covalent postfabrication functionalization is a promising strategy to achieve efficient matrix modification decoupled of general material properties. To this end, dual-functional macromers were synthesized by free radical polymerization of maleic anhydride with diacetone acrylamide (N-(1,1-dimethyl-3-oxobutyl)acrylamide) and pentaerythritol diacrylate monostearate. Amphiphilic oligomers (M n < 7.5 kDa) with anhydride contents of 7-20% offered cross-linking reactivity to yield rigid hydrogels with gelatinous peptides (E = 4-13 kPa) and good cell adhesion properties. Mildly reactive methyl ketones as second functionality remained intact during hydrogel formation and potential of covalent matrix modification was shown using hydrazide and hydrazine model compounds. Successful secondary dihydrazide cross-linking was demonstrated by an increase of hydrogel stiffness (>40%). Efficient hydrazide/hydrazine immobilization depending on solution pH, hydrogel ketone content as well as ligand concentration for bioconjugation was shown and reversibility of hydrazone formation was indicated by physiologically relevant hydrazide release over 7 days. Proof-of-concept experiments with hydrazido-functionalized hyaluronan demonstrated potential for covalent aECM immobilization. The presented dual-functional macromers have perspective as reactive hydrogel building blocks for various biomedical applications.

Fluorine-Induced Chemiluminescence Detection of Biologically Methylated Tellurium, Selenium, and Sulfur Compounds and Methyldithiocarbhydrazide as a Formaldehyde Derivatization Reagent

NASA Astrophysics Data System (ADS)

Chasteen, Thomas Girard

1990-01-01

The first part of this dissertation describes capillary chromatography coupled to a fluorine-induced chemiluminescence detector as a sensitive method by which biologically methylated metalloids can be determined in the presence of high concentrations of potentially interfering molecules. With a wide linear range and excellent sensitivity, this method was applied to the detection of dimethyl selenide (DMSe), dimethyl diselenide (DMDSe), and dimethyl telluride (DMTe), often found in biological environments in the presence of interfering methylated sulfur gases, such as methanethiol, dimethyl sulfide, dimethyl disulfide, and dimethyl trisulfide. Detection limits for DMSe, DMDSe, and DMTe were 30, 9, and 7 picograms, respectively. This DMTe detection limit is the lowest reported to date for a volatile tellurium gas. A variety of selenium-resistant bacteria emitted mixtures of methylated sulfur/selenium gases when dosed with inorganic selenium salts in the presence of sulfur containing growth media. One of the gases detected was dimethyl selenenyl sulfide, CH_3SeSCH _3, reported here for the first time in headspace above microorganisms. In addition, this detector responded to reduced phosphorus compounds such as phosphine. The detection limit for this compound was 2.8 picograms. Detection limits for alkylated phosphines trimethyl and triethyl phosphine were 0.5 and 17 picograms respectively, based on the relative response of these compounds compared to dimethyl sulfide. This method can be used for the simultaneous determination of methylated sulfur, selenium, tellurium compounds found in biological systems. Part II of this dissertation describes work with methyldithiocarbhydrazide, a compound that has been synthesized for use as a derivatization reagent to capture formaldehyde in the gas phase. Chosen for its ability to react in a manner similar to 2,4-dinitrophenylhydrazine, this molecule was selected based on two structural characteristics: a hydrazine tag to react with and thereby capture carbonyls and a methyl sulfide group to allow for sensitive detection by fluorine-induced chemiluminescence. Although in the final analysis methyldithiocarbohydrazide failed as a successful means by which formaldehyde can be determined using gas chromatography in conjunction with fluorine-induced chemiluminescence, it did successfully derivatize formaldehyde in both solution and the gas phase without the need for low pH conditions.

Catastrophic Failure Modes Assessment of the International Space Station Alpha

NASA Technical Reports Server (NTRS)

Lutz, B. E. P.; Goodwin, C. J.

1996-01-01

This report summarizes a series of analyses to quantify the hazardous effects of meteoroid/debris penetration of Space Station Alpha manned module protective structures. These analyses concentrate on determining (a) the critical crack length associated with six manned module pressure wall designs that, if exceeded, would lead to unstopped crack propagation and rupture of manned modules, and (b) the likelihood of crew or station loss following penetration of unsymmetrical di-methyl hydrazine tanks aboard the proposed Russian FGB ('Tug') propulsion module and critical elements aboard the control moment gyro module (SPP-1). Results from these quantified safety analyses are useful in improving specific design areas, thereby reducing the overall likelihood of crew or station loss following orbital debris penetration.

Evaluation of the potential carcinogenic activity of Senna and Cascara glycosides for the rat colon.

PubMed

Mereto, E; Ghia, M; Brambilla, G

1996-03-19

Anthraquinone glycosides of Senna and Cascara were investigated for their ability to induce aberrant crypt foci (ACF) in the rat colon mucosa, which are considered putative preneoplastic lesions. Dietary exposure to high doses of these glycosides for 56 successive days did not cause the appearance of ACF or increase in incidence of ACF induced by 1,2-dimethyl-hydrazine (DMH). However, in rats treated with both DMH and the highest dose of glycosides, the average number of aberrant crypts per focus, considered a consistent predictor of tumor outcome, was higher than in rats given DMH alone. These findings suggest that Senna and Cascara glycoside might behave as weak promoters in rat colon carcinogenesis.

N-nitrosodimethylamine (NDMA) formation during ozonation of N,N-dimethylhydrazine compounds: Reaction kinetics, mechanisms, and implications for NDMA formation control.

PubMed

Lim, Sungeun; Lee, Woongbae; Na, Soyoung; Shin, Jaedon; Lee, Yunho

2016-11-15

Compounds with N,N-dimethylhydrazine moieties ((CH 3 ) 2 N-N-) form N-nitrosodimethylamine (NDMA) during ozonation, but the relevant reaction chemistry is hitherto poorly understood. This study investigated the reaction kinetics and mechanisms of NDMA formation during ozonation of unsymmetrical dimethylhydrazine (UDMH) and daminozide (DMZ) as structural model N,N-dimethylhydrazine compounds. The reaction of ozone with these NDMA precursor compounds was fast, and k O3 at pH 7 was 2 × 10 6  M -1  s -1 for UDMH and 5 × 10 5  M -1  s -1 for DMZ. Molar NDMA yields (i.e., Δ[NDMA]/Δ[precursor] × 100) were 84% and 100% for UDMH and DMZ, respectively, determined at molar ozone dose ratio ([O 3 ] 0 /[precursor] 0 ) of ≥4 in the presence of tert-butanol as hydroxyl radical (OH) scavenger. The molar NDMA yields decreased significantly in the absence of tert-butanol, indicating OH formation and its subsequent reaction with the parent precursors forming negligible NDMA. The k OH at pH 7 was 4.9 × 10 9  M -1  s -1 and 3.4 × 10 9  M -1  s -1 for UDMH and DMZ, respectively. Reaction mechanisms are proposed in which an ozone adduct is formed at the nitrogen next to N,N-dimethylamine which decomposes via homolytic and heterolytic cleavages of the -N + -O-O-O - bond, forming NDMA as a final product. The heterolytic cleavage pathway explains the significant OH formation via radical intermediates. Overall, significant NDMA formation was found to be unavoidable during ozonation or even O 3 /H 2 O 2 treatment of waters containing N,N-dimethylhydrazine compounds due to their rapid reaction with ozone forming NDMA with high yield. Thus, source control or pre-treatment of N,N-dimethylhydrazine precursors and post-treatment of NDMA are proposed as the mitigation options. Copyright © 2016 Elsevier Ltd. All rights reserved.

Study of complex formation of 5,5'-(2 E, 2' E)-2,2'-(ethane-1,2-diylidene)bis(hydrazine-1-yl-2-ylidene)bis(4-amino-4H-1,2,4-triazole-3-thiol) (HYT) macrocyclic ligand with Cd2+ cation in non-aqueous solution by spectroscopic and conductometric methods

NASA Astrophysics Data System (ADS)

Mallaekeh, Hassan; Shams, Alireza; Shaker, Mohammad; Bahramzadeh, Ehsan; Arefi, Donya

2014-12-01

In this paper the complexation reaction of the 5,5'-(2 E,2' E)-2,2'-(ethane-1,2-diylidene)bis(hydrazine-1-yl-2-ylidene)bis(4-amino-4H-1,2,4-triazole-3-thiol) ligand (HYT) with Cd2+ education was studied in some binary mixtures of methanol (MeOH), n-propanol (PrOH) and dimethyl-formamide (DMF) at different temperatures using the conductometry and spectrophotometry. The stability constants of the complex was determined using a GENPLOT computer program. The conductance data and absorbance-mole ratio plots show that in all solvent systems, the stoichiometry of the complex formed between (HYT) and Cd2+ cation is 1: 1. The obtained results show that the stability of (HYT)-Cd complex is sensitive to the mixed solvents composition. The values of thermodynamic parameters (Δ G ∘, Δ H ∘, and Δ S ∘) for formation of (HYT)-Cd complex were obtained from temperature dependence of the stability constant using the van't Hoff plots. The results show that in most cases, the complex are enthalpy destabilized but entropy stabilized and the complex formation is affected by pH, time, temperature and the nature of the solvent.

Examination of the liver in personnel working with liquid rocket propellant

PubMed Central

Petersen, Palle; Bredahl, Erik; Lauritsen, Ove; Laursen, Thomas

1970-01-01

Petersen, P., Bredahl, E., Lauritsen, O., and Laursen, T. (1970).Brit. J. industr. Med.,27, 141-146. Examination of the liver in personnel working with liquid rocket propellants. Personnel working with liquid rocket propellants were subjected to routine health examinations, including liver function tests, as the propellant, unsymmetrical dimethylhydrazine (UDMH) is potentially toxic to the liver. In 46 persons the concentrations of serum alanine aminotransferase (SGPT) were raised. Liver biopsy was performed in 26 of these men; 6 specimens were pathological (fatty degeneration), 5 were uncertain, and 15 were normal. All 6 pathological biopsies were from patients with a raised SGPT at the time of biopsy. Of the 15 persons with a normal liver biopsy, 14 had a normal SGPT, while one (who was an alcoholic) had a raised SGPT. The connection between SGPT and histology of the liver, as well as the possible causal relation between the pathological findings and exposure to UDMH, is discussed. Images PMID:5428632

[IMMUNOCYTOCHEMICAL ANALYSIS OF THE DISTURBANCES IN THE STRUCTURE OF SYNAPTONEMAL COMPLEXES IN SPERMATOCYTE NUCLEI IN MICE UNDER EXPOSURE TO ROCKET FUEL COMPONENT].

PubMed

Lovinskaya, A V; Kolumbayeva, S Zh; Abilev, S K; Kolomiets, O L

2016-01-01

There was performed an assessment of genotoxic effects of rocket fuel component--unsymmetrical dimethylhydrazine (UDMH, heptyl)--on forming germ cells of male mice. Immunocytochemically there was studied the structure of meiotic nuclei at different times after the intraperitoneal administration of UDMH to male mice. There were revealed following types of disturbances of the structure of synaptonemal complexes (SCs) of meiotic chromosomes: single and multiple fragments of SCs associations of autosomes with a sex bivalent, atypical structure of the SCs with a frequency higher than the reference level. In addition, there were found the premature desinapsis of sex bivalents, the disorder offormation of the genital corpuscle and ring SCs. Established disorders in SCs of spermatocytes, analyzed at 38th day after the 10-days intoxication of animal by the component of rocket fuel, attest to the risk of permanent persistence of chromosomal abnormalities occurring in the pool of stem cells.

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

Hydrazine monitoring in spacecraft

NASA Technical Reports Server (NTRS)

Cross, J. H.; Beck, S. W.; Limero, T. F.; James, J. T.

1992-01-01

Hydrazine (HZ) and monomethyl hydrazine (MMH) are highly toxic compounds used as fuels in the Space Shuttle Orbiter Main Engines and in its maneuvering and reaction control system. Satellite refueling during a mission may also result in release of hydrazines. During extravehicular activities, the potential exists for hydrazines to contaminate the suit and to be brought into the internal atmosphere inadvertantly. Because of the high toxicity of hydrazines, a very sensitive, reliable, interference-free, and real-time method of measurement is required. A portable ion mobility spectrometer (IMS) has exhibited a low ppb detection limit for hydrazines suggesting a promising technology for the detection of hydrazines in spacecraft air. The Hydrazine Monitor is a modified airborne vapor monitor (AVM) with a custom-built datalogger. This off-the-shelf IMS was developed for the detection of chemical warfare agents on the battlefield. After early evaluations of the AVM for hydrazine measurements showed a serious interference from ammonia, the AVM was modified to measure HZ and MMH in the ppb concentration range without interference from ammonia in the low ppm range. A description of the Hydrazine Monitor and how it functions is presented.

Electrochemical oxidation of hydrazine and its derivatives on the surface of metal electrodes in alkaline media

NASA Astrophysics Data System (ADS)

Asazawa, Koichiro; Yamada, Koji; Tanaka, Hirohisa; Taniguchi, Masatoshi; Oguro, Keisuke

Electrochemical oxidation of hydrazine and its derivatives on the surface of various metal electrodes in alkaline media was investigated. A comparison of various polycrystalline metal electrodes (Ni, Co, Fe, Cu, Ag, Au, and Pt) showed that Co and Ni electrodes have a lower onset potential for hydrazine oxidation than the Pt electrode. The onset oxidation potential of APA (aminopolyacrylamide), a hydrazine derivative (-0.127 V vs. reversible hydrogen electrode, RHE), was similar to that of hydrazine hydrate (-0.178 V vs. RHE) in the case of the Co electrode. APA oxidation was possible because of hydrazine desorption that was caused by APA hydrolysis. The hydrolysis reaction was brought about by a heat treatment. This result suggests that the hydrazine hydrolysis reaction of hydrazine derivatives makes it possible to store hydrazine hydrate safely.

Explosive decomposition of hydrazine by rapid compression of a gas volume

NASA Technical Reports Server (NTRS)

Bunker, R. L.; Baker, D. L.; Lee, J. H. S.

1991-01-01

In the present investigation of the initiation mechanism and the explosion mode of hydrazine decomposition, a 20 cm-long column of liquid hydrazine was accelerated into a column of gaseous nitrogen, from which it was separated by a thin Teflon diaphragm, in a close-ended cylindrical chamber. Video data obtained reveal the formation of a froth generated by the acceleration of hydrazine into nitrogen at the liquid hydrazine-gaseous nitrogen interface. The explosive hydrazine decomposition had as its initiation mechanism the formation of a froth at a critical temperature; the explosion mode of hydrazine is a confined thermal runaway reaction.

Hydrazine inhalation hepatotoxicity.

PubMed

Kao, Yung Hsiang; Chong, C H; Ng, W T; Lim, D

2007-10-01

Abstract Hydrazine is a hazardous chemical commonly used as a reactant in rocket and jet fuel cells. Animal studies have demonstrated hepatic changes after hydrazine inhalation. Human case reports of hydrazine inhalation hepatotoxicity are rare. We report a case of mild hepatotoxicity following brief hydrazine vapour inhalation in a healthy young man, which resolved completely on expectant management.

Hydrazine-Compatible Elastomer

NASA Technical Reports Server (NTRS)

Markles, O., F.; Dye, T. G.

1982-01-01

Hydrazine hardly reacts with ethylene propylene diene monomer, even at high temperatures. According to report to tests, EPDM is most hydrazine-compatible material among elastomers. Has strong potential as valve-seat and O-ring seal with hydrazine, especially at high temperatures.

Epithelioid sarcoma of the thumb associated with hydrazine fuel exposure: a case report.

PubMed

Helmers, Scott; Ruland, Robert T; Jacob, Lionel N

2004-01-01

Hydrazine fuels are commonly used propellants for missiles and tactical jet aircraft used by the U.S. Air Force and the National Aeronautical and Space Administration. Hydrazine fuels are known to cause cancer after respiratory exposure or ingestion in laboratory animals and humans. Although hydrazine is known to cause skin irritation, there are no published reports describing cancer developing after cutaneous exposure to hydrazine in humans. Hydrazine is known to cause cancer in animals after skin exposure and is used to induce angiosarcomas in mice after cutaneous exposure. We present a case of an epithelioid sarcoma developing in the thumb of a patient after repeated exposure to hydrazine fuel. We hypothesize that the epithelioid sarcoma is a consequence of cutaneous exposure to hydrazine fuel. Continued efforts to develop less toxic alternative fuels and increased personal protection from occupational exposure are highly recommended.

Hydrazine/Hydrazine sulfate

Integrated Risk Information System (IRIS)

Hydrazine / Hydrazine sulfate ; CASRN 302 - 01 - 2 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Non

Dosimeter Badge Detects Hydrazines

NASA Technical Reports Server (NTRS)

Young, Rebecca C.; Travis, Joshua C.; Moore, Gerald; Rose-Pehrsson, Susan; Carver, Patricia; Brenner, Karen

1993-01-01

Disposable dosimeter badge indicates approximate cumulative exposure to hydrazine or monomethyl hydrazine in air. Indication is change in colors of both paper tapes; one coated with para-N, N-dimethylaminobenzaldehyde. Colors of exposed tapes compared with colors on two preprinted color wheels to obtain estimate of exposure. Badges help minimize risks associated with exposure of personnel to hydrazine or monomethyl hydrazine, or suspected carcinogens. Also used as stationary monitors by taping them on walls or equipment at strategic locations.

Theoretical Study of Indium Compounds of Interest for Organometallic Chemical Vapor Deposition

NASA Technical Reports Server (NTRS)

Cardelino, B. H.; Moore, C. E.; Cardelino, C. A.; Frazier, D. O.; Backmann, K. J.

2000-01-01

The structural. electronic and therinochemical properties of indium compounds which are of interest in halide transport and organometallic chemical vapor deposition processes have been studied by ab initio and statistical mechanics methods. The compounds reported include: indium halides and hydrides (InF, InCl, InCl3, InH, InH2, InH3); indium clusters (In2, In3); methylindium, dimethylindium, and their hydrogen derivatives [In(CH3), In(CH3)H, In(CH3)H2, In(CH3)2, In(CH3)2H]; dimethyl-indium dimer [In2(CH3)4], trimethyl-indium [In(CH3)3]; dehydrogenated methyl, dimethyl and trimethylindium [In(CH3)2CH2, In(CH3)CH2, In(CH2)], trimethylindium adducts with ammonia, trimethylamine and hydrazine [(CH3)3In:NH3, (CH3)3In:N(CH3)3, (CH3)3In:N(H2)N(H2)]; dimethylamino-indium and methylimino-indium [In(CH3)2(NH2), In(CH3)(NH)]; indium nitride and indium nitride dimer (InN, In2N2), indium phosphide, arsenide and antimonide ([InP, InAs, InSb). The predicted electronic properties are based on density functional theory calculations; the calculated thermodynamic properties are reported following the format of the JANAF (Joint Army, Navy, NASA, Air Force) Tables. Equilibrium compositions at two temperatures (298 and 1000 K) have been analyzed for groups of competing simultaneous reactions.

Study of monopropellants for electrothermal thrusters: Analytical task summary report

NASA Technical Reports Server (NTRS)

Kuenzly, J. D.; Grabbi, R.

1973-01-01

The feasibility of operating small thrust level electrothermal thrusters is determined with monopropellants other than MIL-grade hydrazine. The work scope includes analytical study, design and fabrication of demonstration thrusters, and an evaluation test program where monopropellants with freezing points lower than MIL-grade hydrazine are evaluated and characterized to determine their applicability to electrothermal thrusters for spacecraft attitude control. Results of propellant chemistry studies and performance analyses indicated that the most promising candidate monopropellants to be investigated are monomethylhydrazine, Aerozine-50, 77% hydrazine-23% hydrazine azide blend, and TRW formulated mixed hydrazine monopropellant (MHM) consisting of 35% hydrazine-50% monomethylhydrazine-15% ammonia.

A novel fluorescein-based "turn-on" probe for the detection of hydrazine and its application in living cells

NASA Astrophysics Data System (ADS)

Xu, Wen-Zhi; Liu, Wei-Yan; Zhou, Ting-Ting; Yang, Yu-Tao; Li, Wei

2018-03-01

We constructed a novel probe for hydrazine detection based on ICT and PET mechanism. Phthalimide and acetyl ester groups were used as the recognition units. Addition of hydrazine produced a turn-on fluorescence at 525 nm along with the fluorescent color change from dark to yellow. The probe could selectively detect hydrazine over other related interfering species. The detection limit of the probe for hydrazine was calculated to be 0.057 μM which was lower than the EPA standard (0.320 μM). Furthermore, the probe could also be applied for the imaging of hydrazine in living cells.

Epoxide reduction with hydrazine on graphene: a first principles study.

PubMed

Kim, Min Chan; Hwang, Gyeong S; Ruoff, Rodney S

2009-08-14

Mechanisms for epoxide reduction with hydrazine on a single-layer graphene sheet are examined using quantum mechanical calculations within the framework of gradient-corrected spin-polarized density-functional theory. We find that the reduction reaction is mainly governed by epoxide ring opening which is initiated by H transfer from hydrazine or its derivatives. In addition, our calculations suggest that the epoxide reduction by hydrazine may predominantly follow a direct Eley-Rideal mechanism rather than a Langmuir-Hinshelwood mechanism. We also discuss the generation of various hydrazine derivatives during the reduction of graphene oxide with hydrazine and their potential contribution to lowering the barrier height of epoxide ring opening.

Sensitized Liquid Hydrazine Detonation Studies

NASA Technical Reports Server (NTRS)

Rathgeber, K. A.; Keddy, C. P.; Bunker, R. L.

1999-01-01

Vapor-phase hydrazine (N2H4) is known to be very sensitive to detonation while liquid hydrazine is very insensitive to detonation, theoretically requiring extremely high pressures to induce initiation. A review of literature on solid and liquid explosives shows that when pure explosive substances are infiltrated with gas cavities, voids, and/or different phase contaminants, the energy or shock pressure necessary to induce detonation can decrease by an order of magnitude. Tests were conducted with liquid hydrazine in a modified card-gap configuration. Sensitization was attempted by bubbling helium gas through and/or suspending ceramic microspheres in the liquid. The hydrazine was subjected to the shock pressure from a 2 lb (0.9 kg) Composition C-4 explosive charge. The hydrazine was contained in a 4 in. (10.2 cm) diameter stainless steel cylinder with a 122 in(sup 3) (2 L) volume and sealed with a polyethylene cap. Blast pressures from the events were recorded by 63 high speed pressure transducers located on three radial legs extending from 4 to 115 ft (1.2 to 35.1 in) from ground zero. Comparison of the neat hydrazine and water baseline tests with the "sensitized" hydrazine tests indicates the liquid hydrazine did not detonate under these conditions.

Catalysts for the decomposition of hydrazine, hydrazine derivatives and mixtures of both

NASA Technical Reports Server (NTRS)

Sasse, R.

1986-01-01

This invention concerns a catalyst designed for the decomposition of hydrazine, hydrazine derivatives and mixtures of the two. The objective is to develop a catalyst of the type described that is cheap and easy to produce and is also characterized by extremely short response times.

Assembly of N,N-disubstituted hydrazines and 1-aryl-1H-indazoles via copper-catalyzed coupling reactions.

PubMed

Xiong, Xiaodong; Jiang, Yongwen; Ma, Dawei

2012-05-18

CuI-catalyzed coupling of N-acyl-N'-substituted hydrazines with aryl iodides takes place at 60-90 °C to afford N-acyl-N',N'-disubstituted hydrazines regioselectively and thereby gives a facile method for assembling N,N-diaryl hydrazines. N-Acyl-N'-substituted hydrazines can also react with 2-bromoarylcarbonylic compounds at 60-125 °C under the catalysis of CuI/4-hydroxy-l-proline to provide 1-aryl-1H-indazoles.

Hydrazine vapor detonations

NASA Technical Reports Server (NTRS)

Pedley, M. D.; Bishop, C. V.; Benz, F. J.; Bennett, C. A.; Mcclenagan, R. D.

1988-01-01

The detonation velocity and cell widths for hydrazine decomposition were measured over a wide range of temperatures and pressures. The detonation velocity in pure hydrazine was within 5 percent of the calculated C-J velocity. The detonation cell width measurements were interpreted using the Zeldovich-Doering-von Neumann model with a detailed reaction mechanism for hydrazine decomposition. Excellent agreement with experimental data for pure hydrazine was obtained using the empirical relation that detonation cell width was equal to 29 times the kinetically calculated reaction zone length.

Auto-ignition of hydrazine by engineering materials

NASA Technical Reports Server (NTRS)

Perkins, J. H.; Riehl, W. A.

1978-01-01

Hydrazine, being a monopropellant, can explode and/or detonate in contact with some materials. This has been generally recognized and minimized by testing the compatibility of engineering materials with hydrazine at ambient temperature. Very limited tests have been done at elevated temperatures. To assess the potential hazard of hydrazine leakage into a propulsion compartment (boattail), autoignition characteristics of hydrazine were tested on 18 engineering materials and coatings at temperatures of 120 C to over 330 C. Furthermore, since hydrazine can decompose violently in nitrogen or helium, common purging cannot assure safety. Therefore tests were also made in nitrogen. Detonations occurred on contact with five materials in air. Similar tests in nitrogen did not lead to ignition.

Treatment for hydrazine-containing waste water solution

NASA Technical Reports Server (NTRS)

Yade, N.

1986-01-01

The treatment for waste solutions containing hydrazine is presented. The invention attempts oxidation and decomposition of hydrazine in waste water in a simple and effective processing. The method adds activated charcoal to waste solutions containing hydrazine while maintaining a pH value higher than 8, and adding iron salts if necessary. Then, the solution is aerated.

Monomethylhydrazine versus hydrazine fuels - Test results using a 100 pound thrust bipropellant rocket engine

NASA Technical Reports Server (NTRS)

Smith, J. A.; Stechman, R. C.

1981-01-01

A test program was performed to evaluate hydrazine (N2H4) as a fuel for a 445 Newton (100 lbf) thrust bipropellant rocket engine. Results of testing with an identical thruster utilizing monomethylhydrazine (MMH) are included for comparison. Engine performance with hydrazine fuel was essentially identical to that experienced with monomethylhydrazine although higher combustor wall temperatures (approximately 400 F) were obtained with hydrazine. Results are presented which indicate that hydrazine as a fuel is compatible with Marquardt bipropellant rocket engines which use monomethylhydrazine as a baseline fuel.

Test program to demonstrate the stability of hydrazine in propellant tanks

NASA Technical Reports Server (NTRS)

Moran, C. M.; Bjorklund, R. A.

1983-01-01

A 24-month coupon test program to evaluate the decomposition of propellant tanks is reported. The propellant fuel evaluated was monopropellant-grade hydrazine (N2H4), which is normally a colorless, fuming, corrosive, strongly reducing liquid. The degree of hydrazine decomposition was determined by means of chemical analyses of the liquid and evolved gases at the end of the test program. The experimental rates of hydrazine decomposition were determined to be within acceptable limits. The propellant tank materials and material combinations were not degraded by a 2-year exposure to hydrazine propellant. This was verified using change-of-weight determinations and microscopic examination of the specimen surface before and after exposure, and by posttest chemical analyses of hydrazine liquid for residual metal content.

A rhodol-based fluorescent chemosensor for hydrazine and its application in live cell bioimaging

NASA Astrophysics Data System (ADS)

Tiensomjitr, Khomsan; Noorat, Rattha; Wechakorn, Kanokorn; Prabpai, Samran; Suksen, Kanoknetr; Kanjanasirirat, Phongthon; Pewkliang, Yongyut; Borwornpinyo, Suparerk; Kongsaeree, Palangpon

2017-10-01

A rhodol cinnamate fluorescent chemosensor (RC) has been developed for selective detection of hydrazine (N2H4). In aqueous medium, the rhodol-based probe exhibited high selectivity for hydrazine among other molecules. The addition of hydrazine triggered a fluorescence emission with 48-fold enhancement based on hydrazinolysis and a subsequent ring-opening process. The chemical probe also displayed a selective colorimetric response toward N2H4 from colorless solution to pink, readily observed by the naked eye. The detection limit of RC for hydrazine was calculated to be 300 nM (9.6 ppb). RC is membrane permeable and was successfully demonstrated to detect hydrazine in live HepG2 cells by confocal fluorescence microscopy.

[Importance of toxicological studies in animals for elaboration of pathogenetic therapy of hydrazine intoxication].

PubMed

Baryshnikov, I I

1997-01-01

Pathogenesis of poisoning with hydrazine seems complicated. Hydrazines inhibit pyridoxal-dependent enzymes, interfere with carbohydrates transformation and lipid metabolism, alter the processes of energy metabolism. Treatment of poisoning with hydrazine is effective only when containing drug combinations. Based experimentally, recommendations on the combination (phenazepam, be methyl, piracetam, ionol) were supported by chemical testing of the drugs.

A Hydrazine Leak Sensor Based on Chemically Reactive Thermistors

NASA Technical Reports Server (NTRS)

Davis, Dennis D.; Mast, Dion J.; Baker, David L.

1999-01-01

Leaks in the hydrazine supply system of the Shuttle APU can result in hydrazine ignition and fire in the aft compartment of the Shuttle. Indication of the location of a leak could provide valuable information required for operational decisions. WSTF has developed a small, single use sensor for detection of hydrazine leaks. The sensor is composed of a thermistor bead coated with copper(II) oxide (CuO) dispersed in a clay or alumina binder. The CuO-coated thermistor is one of a pair of closely located thermistors, the other being a reference. On exposure to hydrazine the CuO reacts exothermically with the hydrazine and increases the temperature of the coated-thermistor by several degrees. The temperature rise is sensed by a resistive bridge circuit and an alarm registered by data acquisition software. Responses of this sensor to humidity changes, hydrazine concentration, binder characteristics, distance from a liquid leak, and ambient pressure levels as well as application of this sensor concept to other fluids are presented.

A chromogenic and fluorogenic rhodol-based chemosensor for hydrazine detection and its application in live cell bioimaging

NASA Astrophysics Data System (ADS)

Tiensomjitr, Khomsan; Noorat, Rattha; Chomngam, Sinchai; Wechakorn, Kanokorn; Prabpai, Samran; Kanjanasirirat, Phongthon; Pewkliang, Yongyut; Borwornpinyo, Suparerk; Kongsaeree, Palangpon

2018-04-01

A rhodol-based fluorescent probe has been developed as a selective hydrazine chemosensor using levulinate as a recognition site. The rhodol levulinate probe (RL) demonstrated high selectivity and sensitivity toward hydrazine among other molecules. The chromogenic response of RL solution to hydrazine from colorless to pink could be readily observed by the naked eye, while strong fluorescence emission could be monitored upon excitation at 525 nm. The detection process occurred via a ring-opening process of the spirolactone initiated by hydrazinolysis, triggering the fluorescence emission with a 53-fold enhancement. The probe rapidly reacted with hydrazine in aqueous medium with the detection limit of 26 nM (0.83 ppb), lower than the threshold limit value (TLV) of 10 ppb suggested by the U.S. Environmental Protection Agency. Furthermore, RL-impregnated paper strips could detect hydrazine vapor. For biological applicability of RL, its membrane-permeable property led to bioimaging of hydrazine in live HepG2 cells by confocal fluorescence microscopy.

A novel dicyanoisophorone based red-emitting fluorescent probe with a large Stokes shift for detection of hydrazine in solution and living cells

NASA Astrophysics Data System (ADS)

Lv, Hongshui; Sun, Haiyan; Wang, Shoujuan; Kong, Fangong

2018-05-01

A novel dicyanoisophorone based fluorescent probe HP was developed to detect hydrazine. Upon the addition of hydrazine, probe HP displayed turn-on fluorescence in the red region with a large Stokes shift (180 nm). This probe exhibited high selectivity and high sensitivity to hydrazine in solution. The detection limit of HP was found to be 3.26 ppb, which was lower than the threshold limit value set by USEPA (10 ppb). Moreover, the probe was successfully applied to detect hydrazine in different water samples and living cells.

1. Exterior view of LongTerm Hydrazine Silo (T28E), looking southeast. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Exterior view of Long-Term Hydrazine Silo (T-28E), looking southeast. The structure was designed to assess long-term environmental impacts on storage of the Titan's fuel (hydrazine). The low-lying building to the immediate right of the silo is the Fuel Purification Structure (T-28E), constructed during the late 1960s to purify hydrazine for long-term hardware requirements for satellites and space expedition vehicles associated with the Titan III. - Air Force Plant PJKS, Systems Integration Laboratory, Long-Term Hydrazine Silo, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Interactions of Hydrazine and Blowby Gases

NASA Technical Reports Server (NTRS)

Meagher, Nancy E.

2003-01-01

The interactions between hydrazine and blowby gases from pyrovalves was explored in this research project. Investigating the decomposition chemistry of hydrazine through detailed chemical kinetic modeling is a project started last summer while participating in the Summer Faculty Fellowship program. During the 1999-2000 academic year, the chemical kinetic mechanism for hydrazine decomposition developed while a SFF at NASA's White Sands Test Facility was further revised and validated against the limited experimental data in the literature. This mechanism was then used in assessing the effects of blowby gas species on hydrazine decomposition. The combustion products introduced into the fuel line by pyrovalve actuation consist primarily of hydrogen gas. Hydrogen is also a product of the decomposition of hydrazine. Additional gaseous chemical species are introduced into the fuel, as well as metals and metal salts that deposit onto the walls of the fuel line. The deposition process is undoubtedly very rapid, and exothermic. Therefore, the major focus of this summer's work was examining the effects of hydrogen presence on hydrazine decomposition, with some representative calculations including the remaining gaseous species found to exist in blowby gases. Since hydrogen is a product of hydrazine decomposition, all reactions necessary to evaluate its effect on hydrazine decomposition chemistry were in the original mechanism developed. However, the mechanism needed to be considerably expanded to include the reactions of the other gaseous blowby species with hydrazine, all the intermediate species formed in its decomposition, and each other. The expanded mechanism consists of 70 species interacting via a network of 452 reactions. Calculations with molecular hydrogen introduced into hydrazine gas in an inert bath gas indicate that H2 presence as an initial reactant in substantial amounts can dramatically impact the decomposition process for hydrazine. The other gaseous blowby species (CO, CO2, H2O, CH4, O2, and N2) were found to have little effect compared to the inclusion of hydrogen itself as an initial reagent. This result is undoubtedly due, in part, to the fact that the blowby gas used in these calculations consisted of 94.6% H2. A more rigorous examination of the behavior of the full detailed mechanism under a variety of conditions was not performed.

Electroless plating of Ni-B film as a binder-free highly efficient electrocatalyst for hydrazine oxidation

NASA Astrophysics Data System (ADS)

Wen, Xiao-Ping; Dai, Hong-Bin; Wu, Lin-Song; Wang, Ping

2017-07-01

Hydrazine is a promising energy carrier for fuel cells owing to its combined advantages of high theoretical cell voltage, high-power density, and no greenhouse gas emission. By using an electroless plating process, we have prepared a robust Ni-B film grown on Ni foam that is highly effective for hydrazine electrooxidation in alkaline media. The effects of reaction temperature, concentrations of hydrous hydrazine and sodium hydroxide in the fuel solution on performance of hydrazine electrooxidation reaction are investigated. The mechanistic reason for the property advantage of as-prepared Ni-B/Ni foam catalyst over the relevant catalysts is discussed based on careful kinetics studies and characterization. The facile synthesis of Ni-based catalyst with high activity and good stability is of clear significance for the development of hydrous hydrazine as a viable energy carrier.

5. Exterior view of LongTerm Hydrazine Silo (T28E), looking west. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Exterior view of Long-Term Hydrazine Silo (T-28E), looking west. The low-lying building to the left of the silo is the Fuel Purification Structure (T-28E). A hydrazine tank is in the concrete truck well in the immediate foreground. - Air Force Plant PJKS, Systems Integration Laboratory, Long-Term Hydrazine Silo, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Tubing For Sampling Hydrazine Vapor

NASA Technical Reports Server (NTRS)

Travis, Josh; Taffe, Patricia S.; Rose-Pehrsson, Susan L.; Wyatt, Jeffrey R.

1993-01-01

Report evaluates flexible tubing used for transporting such hypergolic vapors as those of hydrazines for quantitative analysis. Describes experiments in which variety of tubing materials, chosen for their known compatibility with hydrazine, flexibility, and resistance to heat.

Synthesis, characterization, crystal structures and DFT studies of some new 1,2,4-triazole and triazolidin derivatives

NASA Astrophysics Data System (ADS)

Abosadiya, Hamza M.; Anouar, El Hassane; Abusaadiya, Salima M.; Hasbullah, Siti Aishah; Yamin, Bohari M.

2018-01-01

A simple efficient method for synthesis of some new 1,2,4-Triazole and Triazolidin derivatives namely, 5-(4-methoxyphenyl)-2-phenyl-2,4-dihydro-3H-1,2,4-triazole-3-thione (1a), (2-chlorophenyl)(3,3-dimethyl-1-phenyl-5-thioxo-1,2,4-triazolidin-4-yl)methanone (1b) and (2-iodophenyl)(3,3-dimethyl-1-phenyl-5-thioxo-1,2,4-triazolidin-4-yl)methanone (1c) have been synthesized in high yields from the reaction of carbonoyl isothiocyanate with phenyl hydrazine. The final products were characterized by FT-IR, 1H and 13C NMR spectroscopic techniques. X-ray crystallographic studies showed that 1a crystallized in triclinic crystal system with space group Pī, while both 1b and 1c crystallized in orthorhombic crystal system with space group Pna21. The asymmetric unit of 1a consists two crystallographically independent molecules, while only one molecule in asymmetric unit for both 1b and 1c compounds. All molecules possess Csbnd H ….S intramolecular hydrogen bonds which formed a pseudo-six-membered ring. Experimental results have been confirmed by the state-of-art density functional theory (DFT) in gas and solvent phase by using five different hybrid functionals B3LYP, B3P86, CAM-B3LYP, M06-2X and PBE0 combined with 6-311++G(d, p) basis set. The experimental data are relatively well produced, and relatively good correlations are obtained between the predicted and experimental data.

Genetic analysis of the dsz promoter and associated regulatory regions of Rhodococcus erythropolis IGTS8.

PubMed Central

Li, M Z; Squires, C H; Monticello, D J; Childs, J D

1996-01-01

The dsz gene cluster of Rhodococcus erythropolis IGTS8 comprises three genes, dszA, dszB, and dszC, whose products are involved in the conversion of dibenzothiophene (DBT) to 2-hydroxybiphenyl and sulfite. This organism can use DBT as the sole sulfur source but not as a carbon source. Dsz activity is repressed by methionine, cysteine, Casamino Acids, and sulfate but not by DBT or dimethyl sulfoxide. We cloned 385 bp of the DNA immediately 5' to dszA in front of the reporter gene lacZ of Escherichia coli. We showed that this region contains a Rhodococcus promoter and at least three dsz regulatory regions. After hydrazine mutagenesis of this DNA, colonies that were able to express beta-galactosidase in the presence of Casamino Acids were isolated. Sequencing of these mutants revealed two possible regulatory regions. One is at -263 to -244, and the other is at -93 to -38, where -1 is the base preceding the A of the initiation codon ATG of dszA. An S1 nuclease protection assay showed that the start of the dsz promoter is the G at -46 and that transcription is repressed by sulfate and cysteine but not by dimethyl sulfoxide. The promoter encompasses a region of potential diad symmetry that may contain an operator. Immediately upstream of the promoter is a protein-binding domain between -146 and -121. Deletion of this region did not affect repression, but promoter activity appeared to be reduced by threefold. Thus, it could be an activator binding site or an enhancer region. PMID:8932295

Photoelectrochemical generation of hydrogen and electricity from hydrazine hydrate using BiVO4 electrodes.

PubMed

Pilli, Satyananda Kishore; Summers, Kodi; Chidambaram, Dev

2015-06-07

This study demonstrates solar driven oxidation of hydrazine hydrate and the simultaneous production of hydrogen and electricity in photoelectrochemical cells and photofuel cells, respectively, using a visible light active molybdenum doped BiVO4 photoelectrode. The developed photoelectrodes exhibited tremendous efficiency towards anodic oxidation of hydrous hydrazine with continuous and stable hydrogen evolution at the Pt cathode under benign pH and zero bias conditions. Significantly, the photofuel cell containing hydrazine hydrate fuel has generated electricity with a high open circuit potential of 0.8 V. The presence of bicarbonate ions in the electrolyte has played a significant role in enhancing the kinetics of photoelectrochemical oxidation of hydrazine and improved the hydrogen and electricity generation efficiency thus avoiding the integration of an oxidation electrocatalyst. In addition, molybdenum doped BiVO4 as a possible photoelectrochemical hydrazine sensor has been investigated and the electrode photocurrent was found to be linearly dependent on the concentration of the hydrazine hydrate in the range of 20-90 mM with a correlation coefficient of 0.9936.

Hydrazine vapor inactivates Bacillus spores

NASA Astrophysics Data System (ADS)

Schubert, Wayne W.; Engler, Diane L.; Beaudet, Robert A.

2016-05-01

NASA policy restricts the total number of bacterial spores that can remain on a spacecraft traveling to any planetary body which might harbor life or have evidence of past life. Hydrazine, N2H4, is commonly used as a propellant on spacecraft. Hydrazine as a liquid is known to inactivate bacterial spores. We have now verified that hydrazine vapor also inactivates bacterial spores. After Bacillus atrophaeus ATCC 9372 spores deposited on stainless steel coupons were exposed to saturated hydrazine vapor in closed containers, the spores were recovered from the coupons, serially diluted, pour plated and the surviving bacterial colonies were counted. The exposure times required to reduce the spore population by a factor of ten, known as the D-value, were 4.70 ± 0.50 h at 25 °C and 2.85 ± 0.13 h at 35 °C. These inactivation rates are short enough to ensure that the bioburden of the surfaces and volumes would be negligible after prolonged exposure to hydrazine vapor. Thus, all the propellant tubing and internal tank surfaces exposed to hydrazine vapor do not contribute to the total spore count.

A chromogenic and fluorogenic rhodol-based chemosensor for hydrazine detection and its application in live cell bioimaging.

PubMed

Tiensomjitr, Khomsan; Noorat, Rattha; Chomngam, Sinchai; Wechakorn, Kanokorn; Prabpai, Samran; Kanjanasirirat, Phongthon; Pewkliang, Yongyut; Borwornpinyo, Suparerk; Kongsaeree, Palangpon

2018-04-15

A rhodol-based fluorescent probe has been developed as a selective hydrazine chemosensor using levulinate as a recognition site. The rhodol levulinate probe (RL) demonstrated high selectivity and sensitivity toward hydrazine among other molecules. The chromogenic response of RL solution to hydrazine from colorless to pink could be readily observed by the naked eye, while strong fluorescence emission could be monitored upon excitation at 525 nm. The detection process occurred via a ring-opening process of the spirolactone initiated by hydrazinolysis, triggering the fluorescence emission with a 53-fold enhancement. The probe rapidly reacted with hydrazine in aqueous medium with the detection limit of 26 nM (0.83 ppb), lower than the threshold limit value (TLV) of 10 ppb suggested by the U.S. Environmental Protection Agency. Furthermore, RL-impregnated paper strips could detect hydrazine vapor. For biological applicability of RL, its membrane-permeable property led to bioimaging of hydrazine in live HepG2 cells by confocal fluorescence microscopy. Copyright © 2018 Elsevier B.V. All rights reserved.

Effect of hydrazine based deproteination protocol on bone mineral crystal structure.

PubMed

Karampas, I A; Orkoula, M G; Kontoyannis, C G

2012-05-01

In several bone deproteination protocols the chemical agent used for protein cleavage is hydrazine. The effect of hydrazine deproteination method on the crystal size and crystallinity of the bone mineral was studied. Bovine bones were subjected to this protocol and the crystal size and crystallinity of the remaining bone mineral were determined by X-ray Diffraction (XRD), by measuring the width at the half of the maximum intensity of the (002) reflection. It was found that hydrazine deproteination induces noteworthy increase of crystal size and crystallinity. The effect was enhanced by increasing hydrazine temperature from 25 to 55°C. Furthermore, infrared spectroscopy revealed that hydrazine facilitates the removal of carbonate and acid phosphate ions from bone mineral. It is proposed that the mechanism of modification of crystal size and crystallinity lies on the removal of these ions thus, resulting in crystal re-organization.

Upgrading non-oxidized carbon nanotubes by thermally decomposed hydrazine

NASA Astrophysics Data System (ADS)

Wang, Pen-Cheng; Liao, Yu-Chun; Liu, Li-Hung; Lai, Yu-Ling; Lin, Ying-Chang; Hsu, Yao-Jane

2014-06-01

We found that the electrical properties of conductive thin films based on non-oxidized carbon nanotubes (CNTs) could be further improved when the CNTs consecutively underwent a mild hydrazine adsorption treatment and then a sufficiently effective thermal desorption treatment. We also found that, after several rounds of vapor-phase hydrazine treatments and baking treatments were applied to an inferior single-CNT field-effect transistor device, the device showed improvement in Ion/Ioff ratio and reduction in the extent of gate-sweeping hysteresis. Our experimental results indicate that, even though hydrazine is a well-known reducing agent, the characteristics of our hydrazine-exposed CNT samples subject to certain treatment conditions could become more graphenic than graphanic, suggesting that the improvement in the electrical and electronic properties of CNT samples could be related to the transient bonding and chemical scavenging of thermally decomposed hydrazine on the surface of CNTs.

Hydrazine Sulfate (PDQ®)—Health Professional Version

Cancer.gov

Hydrazine sulfate has shown no anticancer activity in randomized clinical trials. Data on its effectiveness in cancer-related cachexia are inconclusive. Get detailed information about hydrazine sulfate as a treatment for people with cancer in this summary for clinicians.

Hydrazine Detection with a Tunable Diode Laser Spectrometer

NASA Technical Reports Server (NTRS)

Houseman, John; Webster, C. R.; May, R. D.; Anderson, M. S.; Margolis, J. S.; Jackson, Julie R.; Brown, Pamela R.

1999-01-01

Several instruments have been developed to measure low concentrations of hydrazine but none completely meet the sensitivity requirements while satisfying additional criteria such as quick response, stable calibration, interference free operation, online operation, reasonable cost, etc. A brief review is presented of the current technology including the electrochemical cell, the ion mobility spectrometer, the mass spectrometer, and the gas chromatograph. A review of the advantages and disadvantages of these instruments are presented here. The review also includes commercially unavailable technology such as the electronic nose and the Tunable Diode Laser (TDL) IR Spectrometer. It was found that the TDL could meet the majority of these criteria including fast response, minimum maintenance, portability, and reasonable cost. An experiment was conducted to demonstrate the feasibility of such a system using an existing (non-portable) instrument. A lead-salt tunable diode laser, cooled to 85 degrees Kelvin was used to record direct absorption and second-derivative spectra of Hydrazine at several pressures to study the sensitivity to low levels of Hydrazine. Spectra of NH3 and CO2 were used for wavelength identification of the scanned region. With a pathlength of 80 m, detection sensitivities of about 1 ppb were achieved for hydrazine in dry nitrogen at a cell pressure of 100 mbar. For spectroscopic detection of Hydrazine, spectral regions including strong Ammonia or Carbon Dioxide lines must be avoided. Strong Hydrazine absorption features were identified at 940/cm showing minimal contribution from Ammonia interferences as suitable candidates for Hydrazine gas detection. For the studies reported here, the particular laser diode could only cover the narrow regions near 962/cm and 965/cm where strong Ammonia interferences were expected. However, the high resolution (0.001/cm) of the TDL spectrometer allowed individual lines of Hydrazine to be identified away from interferences from either Ammonia or Carbon Dioxide, especially at lower pressures. A Hydrazine line was identified at 961.75/cm which was free from Ammonia absorption and would be suitable to monitor hydrazine levels. This paper also shows data on the degradation of the detectivity of Hydrazine with increasing pressure. Several design options for a portable unit are presented, including designs with near IR and Quantum Cascade laser components which do not require liquid nitrogen cooling.

The catalysis of hydrazines

NASA Technical Reports Server (NTRS)

Tanatar, S.

1987-01-01

Hydrazine sulfate in a hot aqueous solution can be catalyzed in the direction of 3 N2H4 = 4 NH3 + N2. Free hydrazine in a hot aqueous solution dissociates in the presence of platinum in the following direction: 2 N2H4 = 2 NH3 + N2 + H2. In the presence of sodium hydroxide, the catalytic dissociation of hydrazine takes a third direction: 3 N2H4 = 2 NH3 + 2 N3 + 3 H2.

The Effects of Amine Based Missile Fuels on the Activated Sludge Process.

DTIC Science & Technology

1979-10-01

centrations found to cause no significant effect on sewage treatment efficiency are 74 mg/i for UDMH, 44 mg/k for HZ, and 蕔 mg/k for MMH. Ammonia ...EXPERIMENTAL METHODS AND MATERIALS ........... 9 1. Substrate Base .. ................... 9 2. Supplemental Requirements. ............. 11 a. Nitrogen...Recycle .. ....... 5 3 Tyndall Sewage Treatment Plant .. .............. 10 4 Theoretical Effluent COD and Ammonia Nitrogen as a Function of Mean Cell

Becton-Dickson Model 420 Fluorescence-Activated Cell Sorter (FACS).

DTIC Science & Technology

1986-05-01

respectively) have been associated with certain autoimmune or immunodeficient diseases. The effects of UDMH on Lyt. antigens were previously evaluated...measured in cells from feline leukemia virus (FeLV)-infected cats and normal cat cells. The measurements are performed using the calcium-specific dye...ucavd as a stimulator, which allows for quantitation of " . phagocytosis activity of the cells. c) Quantitation of IL-2 receptor site on feline and murine

Determination of transformation products of unsymmetrical dimethylhydrazine in water using vacuum-assisted headspace solid-phase microextraction.

PubMed

Orazbayeva, Dina; Kenessov, Bulat; Psillakis, Elefteria; Nassyrova, Dayana; Bektassov, Marat

2018-06-22

A new, sensitive and simple method based on vacuum-assisted headspace solid-phase microextraction (Vac-HSSPME) followed by gas chromatography-mass-spectrometry (GC-MS), is proposed for the quantification of rocket fuel unsymmetrical dimethylhydrazine (UDMH) transformation products in water samples. The target transformation products were: pyrazine, 1-methyl-1H-pyrazole, N-nitrosodimethylamine, N,N-dimethylformamide, 1-methyl-1Н-1,2,4-triazole, 1-methyl-imidazole and 1H-pyrazole. For these analytes and within shorter sampling times, Vac-HSSPME yielded detection limits (0.5-100 ng L -1 ) 3-10 times lower than those reported for regular HSSPME. Vac-HSSPME sampling for 30 min at 50 °C yielded the best combination of analyte responses and their standard deviations (<15%). 1-Formyl-2,2-dimethylhydrazine and formamide were discarded because of the poor precision and accuracy when using Vac-HSSPME. The recoveries for the rest of the analytes ranged between 80 and 119%. The modified Mininert valve and Thermogreen septum could be used for automated extraction as it ensured stable analyte signals even after long waiting times (>24 h). Finally, multiple Vac-HSSME proved to be an efficient tool for controlling the matrix effect and quantifying UDMH transformation products. Copyright © 2018 Elsevier B.V. All rights reserved.

A highly sensitive and selective off-on fluorescent chemosensor for hydrazine based on coumarin β-diketone

NASA Astrophysics Data System (ADS)

Wu, Wei-Na; Wu, Hao; Wang, Yuan; Mao, Xian-Jie; Zhao, Xiao-Lei; Xu, Zhou-Qing; Fan, Yun-Chang; Xu, Zhi-Hong

2018-01-01

A coumarin-based sensor C1, namely 3-acetoacetylcoumarin was designed, synthesized and applied for hydrazine detection. Hydrazinolysis of the chemosensor gives a fluorescent coumarin-pyrazole product C1 - N2H4 [3-(3-methyl-1H-pyrazol-5-yl)coumarin], and thus resulting in a prominent fluorescence off-on response toward hydrazine under physiological conditions. The probe is highly selective toward hydrazine over cations, anions and other biologically/environmentally abundant analytes. The detection limit of the probe is 3.2 ppb. The sensing mechanism was supported by 1H NMR, IR, MS and DFT calculation. The application of the fluorescent probe in monitoring intracellular hydrazine in glioma cell line U251 was also demonstrated.

Hydrazine reagents as derivatizing agents in environmental analysis--a critical review.

PubMed

Vogel, M; Büldt, A; Karst, U

2000-04-01

Hydrazine reagents are a well-known group of derivatizing agents for the determination of aldehydes and ketones in liquid and gaseous samples. Within this article, the most important hydrazine reagents are critically summarized, and their major applications in different fields, including environmental analysis, food chemistry and industrial analysis are introduced. As 2,4-dinitrophenylhydrazine (DNPH) is the basic reagent for several international standard procedures, its properties are discussed in detail. Particular focus is directed on the chemistry of the hydrazine reagents, and chemical interferences are considered. Recent methods for the determination of various oxidants using hydrazine reagents are presented as well. Due to limited space, this review does not cover the related field of carbohydrate analysis, although many chemical aspects are similar.

Cyclic voltammetry deposition of copper nanostructure on MWCNTs modified pencil graphite electrode: An ultra-sensitive hydrazine sensor.

PubMed

Heydari, Hamid; Gholivand, Mohammad B; Abdolmaleki, Abbas

2016-09-01

In this study, Copper (Cu) nanostructures (CuNS) were electrochemically deposited on a film of multiwall carbon nanotubes (MWCNTs) modified pencil graphite electrode (MWCNTs/PGE) by cyclic voltammetry method to fabricate a CuNS-MWCNTs composite sensor (CuNS-MWCNT/PGE) for hydrazine detection. Scanning electron microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDX) were used for the characterization of CuNS on the MWCNTs matrix. The composite of CuNS-MWCNTs was characterized with cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The preliminary studies showed that the proposed sensor have a synergistic electrocatalytic activity for the oxidation of hydrazine in phosphate buffer. The catalytic currents of square wave voltammetry had a linear correlation with the hydrazine concentration in the range of 0.1 to 800μM with a low detection limit of 70nM. Moreover, the amperometric oxidation current exhibited a linear correlation with hydrazine concentration in the concentration range of 50-800μM with the detection limit of 4.3μM. The proposed electrode was used for the determination of hydrazine in real samples and the results were promising. Empirical results also indicated that the sensor had good reproducibility, long-term stability, and the response of the sensor to hydrazine was free from interferences. Moreover, the proposed sensor benefits from simple preparation, low cost, outstanding sensitivity, selectivity, and reproducibility for hydrazine determination. Copyright © 2016. Published by Elsevier B.V.

Hydrazine Sulfate (PDQ®)—Patient Version

Cancer.gov

Hydrazine sulfate has shown no anticancer activity in randomized clinical trials. It was reported in some clinical trials to be helpful in treating poor appetite and weight loss due to cancer. Learn more about hydrazine sulfate as a treatment for people with cancer in this expert-reviewed summary.

Antisymmetric Amino-Wagging Band of Hydrazine up toK‧ = 13 Levels

NASA Astrophysics Data System (ADS)

Gulaczyk, Iwona; Kre, Marek; Valentin, Alain

1997-12-01

A newly recorded high-resolution infrared spectrum of hydrazine has been studied in the 729-1198 cm-1region (the ν12antisymmetric wagging band) with a resolution of 0.002 cm-1. About 1350 transitions withK‧ from 7 to 13 have been newly assigned and about 2350 transitions with lower values ofK‧ reanalyzed with the improved precision. The effective parameters have been calculated separately for each value ofK‧ using the Hougen-Ohashi hamiltonian for hydrazine. The extended assignment completes the analysis of the ν12band of hydrazine.

Remediation of Cr(VI)-Contaminated Soil Using the Acidified Hydrazine Hydrate.

PubMed

Ma, Yameng; Li, Fangfang; Jiang, Yuling; Yang, Weihua; Lv, Lv; Xue, Haotian; Wang, Yangyang

2016-09-01

Acidified hydrazine hydrate was used to remediate Cr(VI)-contaminated soil. The content of water-soluble Cr(VI) in contaminated soil was 4977.53 mg/kg. The optimal initial pH of hydrazine hydrate solution, soil to solution ratio and molar ratio of Cr(VI) to hydrazine hydrate for remediation of Cr(VI)-contaminated soil were 5.0, 3:1 and 1:3, respectively. Over 99.50 % of water-soluble Cr(VI) in the contaminated soil was reduced at the optimal condition within 30 min. The remediated soil can keep stable within 4 months. Meanwhile the total phosphorus increased from 0.47 to 4.29 g/kg, indicating that using of acidified hydrazine hydrate is an effective method to remediate Cr(VI)-contaminated soil.

Possible Protective Effects of Quercetin and Sodium Gluconate Against Colon Cancer Induction by Dimethylhydrazine in Mice.

PubMed

Saleem, T H; Attya, A M; Ahmed, E A; Ragab, S M M; Ali Abdallah, M A; Omar, H M

2015-01-01

Micronutrients in food have been found to have chemopreventive effects, supporting the conclusions from epidemiologie studies that consumption of fresh fruits and vegetables reduces cancer risk. The present study was carried out to evaluate the role of querctin (Q) and sodium gluconate (GNA) supplementation separately or in combination in ameliorating promotion of colon tumor development by dimethyl-hydrazine (DMH) in mice. Histopathological observation of colons in mice treated with DMH showed goblet cell dysplasia with inflammatory cell infiltration. This pathological finding was associated with significant alteration in oxidative stress markers in colon tissues and carcinoembryonic antigen (CEA) levels in plasma. Mice co-treated with GNA and Q showed mild changes of absorptive and goblet cells and inflammatory cell infiltration in lamina properia, with improvement in oxidative stress markers. In conclusion, findings of the present study indicate significant roles for reactive oxygen species (ROS) in pathogenesis of DMH-induced colon toxicity and initiation of colon cancer. Also, they suggest that Q, GNA or the combination of both have a positive beneficial effect against DMH induced colonic cancer induction in mice.

Survey - Monomethylhydrazine Propellant/Material Compatibility

DTIC Science & Technology

1977-07-01

MMH, UDMH . Crack growth susceptibility is related to contamination levels of water and carbon dioxide. VII. CONCLUSIONS Based upon the findings of the...per liter Density , grams per 0.870 to 9.874 milliliter at 25’C (770F) Table 2. Monomethylhydrazine Propellant Survey Requirements Constituent, Property...0 en ~ 14 Table 6. Summiary of Properties of 6 Monome-thylhydra7ine Propellant6 Chemical name: methyihydrazine Chemical formula : CH 3N2H 3 Formula

Feasibility of a Modified Chloramine Process for the Production of UDMH and MMH

DTIC Science & Technology

1978-08-31

that phase is provided in this report . Amine Fuels Production Feasibility Demonstration, MCR -75-466, Final Report and Addendurn I - Data Book, Martin ...Final Report , Martin Marietta Corporation, Denver (February 1976) Contract F04701-74-C-0039. Amine Fuels Production Feasibility Demonstration, MCF-75...466, CDRL A305, Volume I, Final Report ; Volume II Economic Analyses; and Volume III, Data Book; Martin Marietta Corporation, Denver (October 1976

Effect of gold nanoparticle as a novel nanocatalyst on luminol-hydrazine chemiluminescence system and its analytical application.

PubMed

Safavi, A; Absalan, G; Bamdad, F

2008-03-10

In this work the catalytic role of unsupported gold nanoparticles on the luminol-hydrazine reaction is investigated. Gold nanoparticles catalyze the reaction of hydrazine and dissolved oxygen to generate hydrogen peroxide and also catalyze the oxidation of luminol by the produced hydrogen peroxide. The result is an intense chemiluminescence (CL) due to the excited 3-aminophthalate anion. In the absence of gold nanoparticles no detectable CL was observed by the reaction of luminol and hydrazine unless an external oxidant is present in the system. The size effect of gold nanoparticles on the CL intensity was investigated. The most intensive CL signals were obtained with 15-nm gold nanoparticles. UV-vis spectra and transmission electron microscopy studies were used to investigate the CL mechanism. The luminol and hydroxide ion concentration, gold nanoparticles size and flow rate were optimized. The proposed method was successfully applied to the determination of hydrazine in boiler feed water samples. Between 0.1 and 30 microM of hydrazine could be determined with a detection limit of 30 nM.

Spectrophotometric determination of pico-molar level of hydrazine by using Alizarin red in water and urine samples

NASA Astrophysics Data System (ADS)

Arulraj, Abraham Daniel; Vijayan, Muthunanthevar; Vasantha, Vairathevar Sivasamy

2015-09-01

In this paper, very simple and rapid sensor has been developed for the spectrophotometric determination of pico-molar level of hydrazine using Alizarin red. There was a decrease of optical intensity of the probe in the presence of hydrazine. The LOD is calculated from the linear graph between 5-100 pM as 0.66 pM of hydrazine which is well below the risk level proposed by Agency for Toxic Substance and Disease Registry. The probe selectivity for the detection of hydrazine was tested in the presence of commonly encountered metal ions and anions. The calibration curves showed good linearity for working ranges from 5-100 pM and 0.5-40 mM respectively, with R2 = 0.9911 and 0.9744, indicate the validity of the Beer-Lambert law. The binding constant and the free energy change values are determined by the Benesi-Hildebrand method. Determination of hydrazine in environmental water and human urine samples are successfully performed by the proposed method with the recovery of 100%.

Spectrophotometric determination of pico-molar level of hydrazine by using Alizarin red in water and urine samples.

PubMed

Arulraj, Abraham Daniel; Vijayan, Muthunanthevar; Vasantha, Vairathevar Sivasamy

2015-09-05

In this paper, very simple and rapid sensor has been developed for the spectrophotometric determination of pico-molar level of hydrazine using Alizarin red. There was a decrease of optical intensity of the probe in the presence of hydrazine. The LOD is calculated from the linear graph between 5-100 pM as 0.66 pM of hydrazine which is well below the risk level proposed by Agency for Toxic Substance and Disease Registry. The probe selectivity for the detection of hydrazine was tested in the presence of commonly encountered metal ions and anions. The calibration curves showed good linearity for working ranges from 5-100 pM and 0.5-40 mM respectively, with R(2)=0.9911 and 0.9744, indicate the validity of the Beer-Lambert law. The binding constant and the free energy change values are determined by the Benesi-Hildebrand method. Determination of hydrazine in environmental water and human urine samples are successfully performed by the proposed method with the recovery of 100%. Copyright © 2015 Elsevier B.V. All rights reserved.

The shock Hugoniot of liquid hydrazine in the pressure range of 3.1 to 21.4 GPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garcia, B.O.; Persson, P-A.

1996-10-01

Impedance matching was used; the technique was similar to Richard Dick`s. Shock pressures were produced using a plane wave explosive driver with different explosives and different reference materials against liq. hydrazine. Velocity of shock wave in the liquid and free surface velocity of the reference material were measured using different pin contact techniques. The experimental Hugoniot appears smooth, with no indication of a phase change. The shock Hugoniot of liq. hydrazine was compared against 3 other liquid Hugoniots (liq. NH3, water, CCl4) and is closest to that for water and in between NH3 and CCl4. The hydrazine Hugoniot was alsomore » compared to the ``Universal`` Hugoniot for liquids. This universal Hugoniot is not a good approximation for the liq. hydrazine in this pressure range.« less

Evaluation of the SSRCT engine with a hydrazine as a fuel, phase 1

NASA Technical Reports Server (NTRS)

Minton, S. J.

1978-01-01

The performance parameters for the space shuttle reaction control thruster (SSRCT) when the fuel is changed from monomethylhydrazine to hydrazine were predicted. Potential problems are higher chamber wall temperature during steady state operation and explosive events during pulse mode operation. Solutions to the problems are suggested. To conduct the analysis, a more realistic film cooling model was devised which considers that hydrazine based fuels are reactive when used as a film coolant on the walls of the combustion chamber. Hydrazine based fuels can decompose exothermally as a monopropellant and also enter into bipropellant reactions with any excess oxidizer in the combustion chamber. It is concluded that the conversion of the thruster from MMH to hydrazine fuel is feasible but that a number of changes would be required to achieve the same safety margins as the monomethylhydrazine-fueled thruster.

Test program to demonstrate the stability of hydrazine in propellant tanks

NASA Technical Reports Server (NTRS)

Moran, C. M.; Sutton, D.

1983-01-01

The suitability of stainless steels and Inconel for long-term hydrazine propellant-storage tanks is investigated. Rectangular coupon samples cut from propellent tanks were sealed with a measured amount of hydrazine in glass capsules, stored at 43 or 60 C, and removed after 6 to 24 months, when corrosion of the coupon and decomposition of the hydrazine was determined, and SEM and electron spectroscopy were performed on some coupons. Corrosion was found to be unmeasurably low for all the coupons, and hydrazine decomposition produced less than 1.0 cu cm of gas per sq cm of wetted surface per year, except in those few cases when catalysis or contamination were detected. Especially good stability was observed for type 304L stainless steel. The decomposition rates determined in the coupon tests are confirmed by preliminary results of actual tank storage trials.

A Review of Hydrazine Sensors: The State of the Art

NASA Technical Reports Server (NTRS)

Meneghelli, B. J.

2004-01-01

Several types of sensors have been developed over the past few years that quantify the vapor concentrations of the hydrazines. These sensor s are able to detect concentrations as low as 10 parts per billion (ppb) up to several parts per million (ppm). The scope of this review wi ll be focused on those sensors that are most current in the marketpla ce as either leak detectors or personnel monitors. Some technical information on the theory of operations of each hydrazine detector will a lso be included. The review will highlight current operations that utilize hydrazine sensors including the Kennedy Space Center (KSC), the United States Air Force (USAF) at Cape Canaveral Air Station (CCAS), USAF F-16 facilities. The orientation of the review will be towards giving users usable practical information on hydrazine sensors.

Mobility Spectrometer Studies on Hydrazine and Ammonia Detection

NASA Technical Reports Server (NTRS)

Niu, William; Eiceman, Gary; Szumlas, Andrew; Lewis, John

2011-01-01

An airborne vapor analyzer for detecting sub- to low- parts-per-million (ppm) hydrazine in the presence of higher concentration levels of ammonia has been under development for the Orion program. The detector is based on ambient pressure ionization and ion mobility characterization. The detector encompasses: 1) a membrane inlet to exclude particulate and aerosols from the analyzer inlet; 2) a method to separate hydrazine from ammonia which would otherwise lead to loss of calibration and quantitative accuracy for the hydrazine determination; and 3) response and quantitative determinations for both hydrazine and ammonia. Laboratory studies were made to explore some of these features including mobility measurements mindful of power, size, and weight issues. The study recommended the use of a mobility spectrometer of traditional design with a reagent gas and equipped with an inlet transfer line of bonded phase fused silica tube. The inlet transfer line provided gas phase separation of neutrals of ammonia from hydrazine at 50 C simplifying significantly the ionization chemistry that underlies response in a mobility spectrometer. Performance of the analyzer was acceptable between ranges of 30 to 80 C for both the pre-fractionation column and the drift tube. An inlet comprised of a combined membrane with valve-less injector allowed high speed quantitative determination of ammonia and hydrazine without cross reactivity from common metabolites such as alcohols, esters, and aldehydes. Preliminary test results and some of the design features are discussed.

Precious-Metal Salt Coatings for Detecting Hydrazines

NASA Technical Reports Server (NTRS)

Dee, Louis A.; Greene, Benjamin

2004-01-01

Substrates coated with a precious-metal salt KAuCl4 have been found to be useful for detecting hydrazine vapors in air at and above a concentration of the order of 0.01 parts per million (ppm). Upon exposure to air containing a sufficient amount of hydrazine for a sufficient time, the coating material undergoes a visible change in color.

4. Exterior view of LongTerm Hydrazine Silo (T28E), looking west. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Exterior view of Long-Term Hydrazine Silo (T-28E), looking west. The low-lying building to the immediate left of the silo is the Fuel Purification Structure (T-28E). - Air Force Plant PJKS, Systems Integration Laboratory, Long-Term Hydrazine Silo, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

2. Exterior view of LongTerm Hydrazine Silo (T28E), looking east. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Exterior view of Long-Term Hydrazine Silo (T-28E), looking east. The low-lying building to the immediate right of the silo is the Fuel Purification Structure T-28E). - Air Force Plant PJKS, Systems Integration Laboratory, Long-Term Hydrazine Silo, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

3. Exterior view of LongTerm Hydrazine Silo (T28E), looking southwest. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Exterior view of Long-Term Hydrazine Silo (T-28E), looking southwest. The low-lying building to the immediate left of the silo is the Fuel Purification Structure (T-28E). - Air Force Plant PJKS, Systems Integration Laboratory, Long-Term Hydrazine Silo, Waterton Canyon Road & Colorado Highway 121, Lakewood, Jefferson County, CO

Analysis of hydrazine in drinking water by isotope dilution gas chromatography/tandem mass spectrometry with derivatization and liquid-liquid extraction.

PubMed

Davis, William E; Li, Yongtao

2008-07-15

A new isotope dilution gas chromatography/chemical ionization/tandem mass spectrometric method was developed for the analysis of carcinogenic hydrazine in drinking water. The sample preparation was performed by using the optimized derivatization and multiple liquid-liquid extraction techniques. Using the direct aqueous-phase derivatization with acetone, hydrazine and isotopically labeled hydrazine-(15)N2 used as the surrogate standard formed acetone azine and acetone azine-(15)N2, respectively. These derivatives were then extracted with dichloromethane. Prior to analysis using methanol as the chemical ionization reagent gas, the extract was dried with anhydrous sodium sulfate, concentrated through evaporation, and then fortified with isotopically labeled N-nitrosodimethylamine-d6 used as the internal standard to quantify the extracted acetone azine-(15)N2. The extracted acetone azine was quantified against the extracted acetone azine-(15)N2. The isotope dilution standard calibration curve resulted in a linear regression correlation coefficient (R) of 0.999. The obtained method detection limit was 0.70 ng/L for hydrazine in reagent water samples, fortified at a concentration of 1.0 ng/L. For reagent water samples fortified at a concentration of 20.0 ng/L, the mean recoveries were 102% with a relative standard deviation of 13.7% for hydrazine and 106% with a relative standard deviation of 12.5% for hydrazine-(15)N2. Hydrazine at 0.5-2.6 ng/L was detected in 7 out of 13 chloraminated drinking water samples but was not detected in the rest of the chloraminated drinking water samples and the studied chlorinated drinking water sample.

SNCR De-NOx within a moderate temperature range using urea-spiked hydrazine hydrate as reductant.

PubMed

Chen, H; Chen, D Z; Fan, S; Hong, L; Wang, D

2016-10-01

In this research, urea-spiked hydrazine hydrate solutions are used as reductants for the Selective Non-Catalytic Reduction (SNCR) De-NOx process below 650 °C. The urea concentration in the urea/hydrazine hydrate solutions is chosen through experimental and theoretical studies. To determine the mechanism of the De-NOx process, thermogravimetric analysis (TGA) of the urea/hydrazine hydrate solutions and their thermal decomposition in air and nitrogen atmospheres were studied to understand their decomposition behaviours and redox characteristics. Then a plug flow reactor (PFR) model was adopted to simulate the De-NOx processes in a pilot scale tubular reactor, and the calculated De-NOx efficiency vs. temperature profiles were compared with experimental results to support the mechanism and choose the proper reductant and its reaction temperature. Both the experimental and calculated results show that when the urea is spiked into hydrazine hydrate solution to make the urea-N content approximately 16.7%-25% of the total N content in the solution, better De-NOx efficiencies can be obtained in the temperature range of 550-650 °C, under which NH3 is inactive in reducing NOx. And it is also proved that for these urea-spiked hydrazine hydrate solutions, the hydrazine decomposition through the pathway N2H4 + M = N2H3 + H + M is enhanced to provide radical H, which is active to reduce NO. Finally, the reaction routes for SNCR De-NOx process based on urea-spiked hydrazine hydrate at the proper temperature are proposed. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effects of aniline impurities on monopropellant hydrazine thruster performance

NASA Technical Reports Server (NTRS)

Holcomb, L.; Mattson, L.; Oshiro, R.

1976-01-01

Both a 0.45-N and a 0.9-N thruster representative of the designs being flown on 3-axis stabilized spacecraft were used in testing various grades of hydrazine for the phenomenon of monopropellant hydrazine thruster catalyst bed poisoning. Both designs employed Shell 405 ABSG spontaneous catalyst. It is found that pulse shape distortion can be minimized, if not eliminated, by using aniline-free hydrazine. The mechanisms for both steady-state and pulse-mode performance loss are associated with the formation of a catalyst coke similar to the polycyclic aromatic poisons encountered in the petroleum industry. These poisoning mechanisms are reversible, with high-temperature operation being required to drive off the aniline coke deposits. It is recommended that a purified-grade hydrazine be considered for any mission that imposes operational conditions on a thruster which can result in aniline-induced poisoning of the catalyst bed.

Synthesis, structurale elucidation and antioxidant study of Ortho-substituted N,N’-bis(benzamidothiocarbonyl)hydrazine derivatives

NASA Astrophysics Data System (ADS)

Firdausiah, Syadza; Hasbullah, S. A.; Yamin, B. M.

2018-03-01

Some bis(thiourea) compounds have been reported to posses excellent performance in pharmaceutical and environmental fields because of their ability to form chelating complexes with various anions and metal ions. Structurally for carbonyl thiourea derivatives, to become a chelating agent, it must adopt cis-configuration. In the present study, four new bis(thiourea) derivatives namely N,N’-bis(o-fluorobenzamidothiocarbonyl)hydrazine (1), N,N’- bis(o-chloro-benzamidothiocarbonyl)hydrazine (2), N,N’-bis(o-nitrobenzamidothiocarbonyl)-hydrazine (3), and N,N’-bis(o-methylbenzamidothiocarbonyl)hydrazine (4) were successfully synthesized and characterized by CHNS microelemental analysis, FTIR, UV-Vis, and 1H and 13C NMR spectroscopy. However chemical crystallography study showed that both thiourea moieties in compound (2) and (3) adopt trans geometry. Therefore they are potential monodentate ligand with two active moieties. DPPH radical scavenging experiment showed that compound (1), (2), and (4) exhibited higher antioxidant activity than ascorbic acid (Vitamin C).

Survey of materials for hydrazine propulsion systems in multicycle extended life applications

NASA Technical Reports Server (NTRS)

Coulbert, C. D.; Yankura, G.

1972-01-01

An assessment is presented of materials compatibility data for hydrazine monopropellant propulsion systems applicable to the Space Shuttle vehicle missions. Materials were evaluated for application over a 10-yr/100-mission operational lifetime with minimum refurbishment. A general materials compatibility rating for a broad range of materials and several propellants based primarily on static liquid propellant immersion testing and an in-depth evaluation of hydrazine decomposition as a function of purity, temperature, material, surface conditions, etc., are presented. The most promising polymeric material candidates for propellant diaphragms and seals appear to have little effect on increasing hydrazine decomposition rates, but the materials themselves do undergo changes in physical properties which can affect their 10-yr performance in multicycle applications. The available data on these physical properties of elastomeric materials as affected by exposure to hydrazine or related environments are presented.

(E)-1,1,4,4-Tetramethyl-2-tetrazene (TMTZ): A Prospective Alternative to Hydrazines in Rocket Propulsion.

PubMed

Dhenain, Anne; Darwich, Chaza; Sabaté, Carlos Miró; Le, Duc-Minh; Bougrine, Anne-Julie; Delalu, Henri; Lacôte, Emmanuel; Payen, Léa; Guitton, Jérôme; Labarthe, Emilie; Jacob, Guy

2017-07-21

1,1,4,4-Tetramethyl-2-tetrazene (TMTZ) is considered as a prospective replacement for toxic hydrazines used in liquid rocket propulsion. The heat of formation of TMTZ was computed and measured, giving values well above those of the hydrazines commonly used in propulsion. This led to a predicted maximum I sp of 337 s for TMTZ/N 2 O 4 mixtures, which is a value comparable to that of monomethylhydrazine. We found that TMTZ has a vapor pressure well below that of liquid hydrazines, and it is far less toxic. Finally, an improved synthesis is proposed, which is compatible with existing industrial production facilities after minor changes. TMTZ is thus an attractive liquid propellant candidate, with a performance comparable to hydrazines but a lower vapor pressure and toxicity. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enthalpy of Formation of N 2 H 4 (Hydrazine) Revisited

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feller, David; Bross, David H.; Ruscic, Branko

2017-08-02

In order to address the accuracy of the long-standing experimental enthalpy of formation of gas-phase hydrazine, fully confirmed in earlier versions of Active Thermochemical Tables (ATcT), the provenance of that value is re-examined in light of new high-end calculations of the Feller-Peterson-Dixon (FPD) variety. An overly optimistic determination of the vaporization enthalpy of hydrazine, which created an unrealistically strong connection between the gas phase thermochemistry and the calorimetric results defining the thermochemistry of liquid hydrazine was identified as the probable culprit. The new enthalpy of formation of gas-phase hydrazine, based on balancing all available knowledge, was determined to be 111.57more » ± 0.47 kJ/mol at 0 K (97.41 kJ/mol at 298.15 K). Close agreement was found between the ATcT (even excluding the latest theoretical result) and FPD enthalpies.« less

Enthalpy of Formation of N2H4 (Hydrazine) Revisited.

PubMed

Feller, David; Bross, David H; Ruscic, Branko

2017-08-17

In order to address the accuracy of the long-standing experimental enthalpy of formation of gas-phase hydrazine, fully confirmed in earlier versions of Active Thermochemical Tables (ATcT), the provenance of that value is re-examined in light of new high-end calculations of the Feller-Peterson-Dixon (FPD) variety. An overly optimistic determination of the vaporization enthalpy of hydrazine, which created an unrealistically strong connection between the gas phase thermochemistry and the calorimetric results defining the thermochemistry of liquid hydrazine, was identified as the probable culprit. The new enthalpy of formation of gas-phase hydrazine, based on balancing all available knowledge, was determined to be 111.57 ± 0.47 kJ/mol at 0 K (97.42 ± 0.47 kJ/mol at 298.15 K). Close agreement was found between the ATcT (even excluding the latest theoretical result) and the FPD enthalpy.

Improved Ablative Materials

DTIC Science & Technology

1967-12-01

Equipment 62 2. Gas Analysis 62 3. Chemical Analysis for Titanium and Boron 63 4. Tensile Strength Determinations 64 5. Density Determinations 64 6. X-ray...mils, and its density was about 4. 45 g/cm 3. Elastic modulus values averaged about 71 x 106 psi for the filament. -X- I. INTRODUCTION Ablative liner...20 4 /50 percent N 2H 4 -50 percent UDMH or L0 2 /LH. The more-energetic propellant systems, using fluorine or FLOX, demand more-effective abla- tive

Chronic Inhalation Toxicity of Unsymmetrical Dimethylhydrazine: Oncogenic Effects

DTIC Science & Technology

1984-10-01

maintained for various time periods postexposure as long as: hamsters, 17 months; mice and rats, 19 months; and dogs , 54 months. The lung was a target organ...Force Base, Ohio R. H. Bruner, Lt Col United States Army BLOCK 18. Subject Terms Peroral Dogs Rats Neoplastic Mice Non-Neoplastic Hamsters BLOCK 19...Abstract An indication of hepatotoxicity in dogs was revealed by transitory elevation in SGPT and BSP values for dogs exposed to 5 ppm. Since the UDMH

Formation of N-nitrosodimethylamine (NDMA) from reaction of monochloramine: a new disinfection by-product.

PubMed

Choi, Junghoon; Valentine, Richard L

2002-02-01

Studies have been conducted specifically to investigate the hypothesis that N-nitrosodimethylamine (NDMA) can be produced by reactions involving monochloramine. Experiments were conducted using dimethylamine (DMA) as a model precursor. NDMA was formed from the reaction between DMA and monochloramine indicating that it should be considered a potential disinfection by-product. The formation of NDMA increased with increased monochloramine concentration and showed maximum in yield when DMA was varied at fixed monochloramine concentrations. The mass spectra of the NDMA formed from DMA and 15N isotope labeled monochloramine (15NH2Cl) showed that the source of one of the nitrogen atoms in the nitroso group in NDMA was from monochloramine. Addition of 0.05 and 0.5 mM of preformed monochloramine to a secondarily treated wastewater at pH 7.2 also resulted in the formation of 3.6 and 111 ng/L of NDMA, respectively, showing that this is indeed an environmentally relevant NDMA formation pathway. The proposed NDMA formation mechanism consists of (i) the formation of 1,1-dimethylhydrazine (UDMH) intermediate from the reaction of DMA with monochloramine followed by, (ii) the oxidation of UDMH by monochloramine to NDMA, and (iii) the reversible chlorine transfer reaction between monochloramine and DMA which is parallel to (i). We conclude that reactions involving monochloramine in addition to classical nitrosation reactions are potentially important pathways for NDMA formation.

Trajectory correction propulsion for TOPS

NASA Technical Reports Server (NTRS)

Long, H. R.; Bjorklund, R. A.

1972-01-01

A blowdown-pressurized hydrazine propulsion system was selected to provide trajectory correction impulse for outer planet flyby spacecraft as the result of cost/mass/reliability tradeoff analyses. Present hydrazine component and system technology and component designs were evaluated for application to the Thermoelectric Outer Planet Spacecraft (TOPS); while general hydrazine technology was adequate, component design changes were deemed necessary for TOPS-type missions. A prototype hydrazine propulsion system was fabricated and fired nine times for a total of 1600 s to demonstrate the operation and performance of the TOPS propulsion configuration. A flight-weight trajectory correction propulsion subsystem (TCPS) was designed for the TOPS based on actual and estimated advanced components.

Propellant material compatibility program and results

NASA Technical Reports Server (NTRS)

Toth, L. R.; Cannon, W. A.; Coulbert, C. D.; Long, H. R.

1976-01-01

The effects of long-term (up to 10 years) contact of inert materials with earth-storable propellants were studied for the purpose of designing chemical propulsion system components that can be used for current as well as future planetary spacecraft. The primary experimental work, and results to date are reported. Investigations include the following propellants: hydrazine, hydrazine-hydrazine nitrate blends, monomethyl-hydrazine, and nitrogen tetroxide. Materials include: aluminum alloys, corrosion-resistant steels, and titanium alloys. More than 700 test specimen capsules were placed in long-term storage testing at 43 C in the special material compatibility facility. Material ratings relative to the 10-year requirement have been assigned.

A diffuse reflectance infrared Fourier transform spectroscopic study of adsorbed hydrazines

NASA Technical Reports Server (NTRS)

Davis, Dennis D.; Kilduff, Jan E.; Koontz, Steven L.

1988-01-01

Diffuse reflectance spectroscopy of fuel hydrazines adsorbed on silica, silica-alumina and alimina surfaces indicates that the primary surface-hydrazine interaction is hydrogen bonding. Hydrazine, on adsorption to a deuterated silica surface, undergoes a rapid H/D exchange with deuterated surface silanol (Si-OD) groups. Adsorption equilibria are rapidly established at room temperature. Monomethylhydrazine and unsymmetrical dimethylhydrazine are similarly adsorbed. On adsorption, the C-H stretching and methyl deformation modes of the methylhydrazines are shifted to higher frequencies by 10 to 20 cm(-1). These shifts are postulated to be due to changes in the lone-pair electro-density on the adjacent nitrogen atom and an electronegativity effect.

Monopropellant hydrazine resistojet: Flight application design

NASA Technical Reports Server (NTRS)

Kurch, C. K.

1973-01-01

The design, development, and testing of an engineering model nominal 20-millipound thrust monopropellant hydrazine resistojet program is directed toward the advanced development of an electrothermal hydrazine thruster (EHT). The EHT decomposes hydrazine thermally and expands the decomposition products through a nozzle to provide the impulse necessary to fulfill spacecraft propulsive requirements. The thruster is capable of operation at pulse widths from 0.050 second to steady state and delivers specific impulse values up to about 230 seconds depending on the duty cycle. The program is comprised of six tasks including analyses, the generation of specifications and other documentation, design, fabrication and test, data correlation, and recommendations for the design of flight units.

Hydrazine levels in formulations of hydralazine, isoniazid, and phenelzine over a 2-year period.

PubMed

Lovering, E G; Matsui, F; Curran, N M; Robertson, D L; Sears, R W

1983-08-01

Hydrazine levels in formulations of hydralazine, isoniazid, and phenelzine have been measured over a 2-year period under ambient conditions and under temperature and humidity stress. Hydralazine tablets are stable under ambient conditions, but the hydrazine level in an injectable formulation increased from 4.5 to 10 micrograms/ml over a 23-month period. Isoniazid tablets are also stable, but hydrazine levels in an elixir and a pyridoxine combination product doubled to 44 micrograms/ml and 19 micrograms/tablet, respectively. Levels in phenelzine tablets appeared to remain constant at approximately 60 micrograms/tablet, with considerable tablet-to-tablet variation.

Application of a palladium hexacyanoferrate film-modified aluminum electrode to electrocatalytic oxidation of hydrazine.

PubMed

Razmi, Habib; Azadbakht, Azadeh; Sadr, Moayad Hossaini

2005-11-01

A palladium hexacyanoferrate (PdHCF) film as an electrocatalytic material was obtained at an aluminum (Al) electrode by a simple electroless dipping method. The modified Al electrode demonstrated a well-behaved redox couple due to the redox reaction of the PdHCF film. The PdHCF film showed an excellent electrocatalytic activity toward the oxidation of hydrazine. The electrocatalytic oxidation of hydrazine was studied by cyclic voltammetry and rotating disk electrode voltammetry techniques. A calibration graph obtained for the hydrazine consisted of two segments (localized at concentration ranges 0.39-10 and 20-75 mM). The rate constant k and transfer coefficient alpha for the catalytic reaction and the diffusion coefficient of hydrazine in the solution D, were found to be 3.11 x 10(3) M(-1) s(-1), 0.52 and 8.03 x 10(-6) cm2 s(-1) respectively. The modified electrode was used to amperometric determination of hydrazine in photographic developer. The interference of ascorbic acid and thiosulfate were investigated and greatly reduced using a thin film of Nafion on the modified electrode. The modified electrode indicated reproducible behavior and a high level of stability during electrochemical experiments, making it particularly suitable for analytical purposes.

The inner workings of the hydrazine synthase multiprotein complex.

PubMed

Dietl, Andreas; Ferousi, Christina; Maalcke, Wouter J; Menzel, Andreas; de Vries, Simon; Keltjens, Jan T; Jetten, Mike S M; Kartal, Boran; Barends, Thomas R M

2015-11-19

Anaerobic ammonium oxidation (anammox) has a major role in the Earth's nitrogen cycle and is used in energy-efficient wastewater treatment. This bacterial process combines nitrite and ammonium to form dinitrogen (N2) gas, and has been estimated to synthesize up to 50% of the dinitrogen gas emitted into our atmosphere from the oceans. Strikingly, the anammox process relies on the highly unusual, extremely reactive intermediate hydrazine, a compound also used as a rocket fuel because of its high reducing power. So far, the enzymatic mechanism by which hydrazine is synthesized is unknown. Here we report the 2.7 Å resolution crystal structure, as well as biophysical and spectroscopic studies, of a hydrazine synthase multiprotein complex isolated from the anammox organism Kuenenia stuttgartiensis. The structure shows an elongated dimer of heterotrimers, each of which has two unique c-type haem-containing active sites, as well as an interaction point for a redox partner. Furthermore, a system of tunnels connects these active sites. The crystal structure implies a two-step mechanism for hydrazine synthesis: a three-electron reduction of nitric oxide to hydroxylamine at the active site of the γ-subunit and its subsequent condensation with ammonia, yielding hydrazine in the active centre of the α-subunit. Our results provide the first, to our knowledge, detailed structural insight into the mechanism of biological hydrazine synthesis, which is of major significance for our understanding of the conversion of nitrogenous compounds in nature.

Concentric-electrode organic electrochemical transistors: case study for selective hydrazine sensing

NASA Astrophysics Data System (ADS)

Pecqueur, S.; Lenfant, S.; Guérin, D.; Alibart, F.; Vuillaume, D.

2017-12-01

We report on hydrazine-sensing organic electrochemical transistors (OECTs) with a design consisting in concentric annular electrodes. The design engineering of these OECTs was motivated by the great potential of using OECT sensing arrays in fields such as bioelectronics. In this work, PEDOT:PSS-based OECTs have been studied as aqueous sensors, specifically sensitive to the lethal hydrazine molecule. These amperometric sensors have many relevant features for the development of hydrazine sensors, such as a sensitivity down to 10-5 M of hydrazine in water, an order of magnitude higher selectivity for hydrazine than for 9 other water soluble common analytes, the capability to recover entirely its base signal after water flushing and a very low voltage operation. The specificity for hydrazine to be sensed by our OECTs is caused by its catalytic oxidation at the gate electrode and enables increasing the output current modulation of the devices. This has permitted the device-geometry study of the whole series of 80 micrometric OECT devices with sub-20-nm PEDOT:PSS layers, channel lengths down to 1 μm and a specific device geometry of coplanar and concentric electrodes. The numerous geometries unravel new aspects of the OECT mechanisms governing the electrochemical sensing behaviours of the device, more particularly the effect of the contacts which are inherent at the micro-scale. By lowering the device cross-talking, micrometric gate-integrated radial OECTs shall contribute to the diminishing of the readout invasiveness and therefore promotes further the development of OECT biosensors.

Enhanced biodegradation of methylhydrazine and hydrazine contaminated NASA wastewater in fixed-film bioreactor.

PubMed

Nwankwoala, A U; Egiebor, N O; Nyavor, K

2001-01-01

The aerobic biodegradation of National Aeronautics and Space Administration (NASA) wastewater that contains mixtures of highly concentrated methylhydrazine/hydrazine, citric acid and their reaction product was studied on a laboratory-scale fixed film trickle-bed reactor. The degrading organisms, Achromobacter sp., Rhodococcus B30 and Rhodococcus J10, were immobilized on coarse sand grains used as support-media in the columns. Under continuous flow operation, Rhodococcus sp. degraded the methylhydrazine content of the wastewater from a concentration of 10 to 2.5 mg/mL within 12 days and the hydrazine from approximately 0.8 to 0.1 mg/mL in 7 days. The Achromobacter sp. was equally efficient in degrading the organics present in the wastewater, reducing the concentration of the methylhydrazine from 10 to approximately 5 mg/mL within 12 days and that of the hydrazine from approximately 0.8 to 0.2 mg/mL in 7 days. The pseudo first-order rate constants of 0.137 day(-1) and 0.232 day(-1) were obtained for the removal of methylhydrazine and hydrazine, respectively, in wastewater in the reactor column. In the batch cultures, rate constants for the degradation were 0.046 and 0.079 day(-1) for methylhydrazine and hydrazine respectively. These results demonstrate that the continuous flow bioreactor afford greater degradation efficiencies than those obtained when the wastewater was incubated with the microbes in growth-limited batch experiments. They also show that wastewater containing hydrazine is more amenable to microbial degradation than one that is predominant in methylhydrazine, in spite of the longer lag period observed for hydrazine containing wastewater. The influence of substrate concentration and recycle rate on the degradation efficiency is reported. The major advantages of the trickle-bed reactor over the batch system include very high substrate volumetric rate of turnover, higher rates of degradation and tolerance of the 100% concentrated NASA wastewater. The results of the present laboratory scale study will be of great importance in the design and operation of an industrial immobilized biofilm reactor for the treatment of methylhydrazine and hydrazine contaminated NASA wastewater.

Inflight performance of the Ulysses reaction control system

NASA Technical Reports Server (NTRS)

McGarry, Andrew; Berry, William; Parker, David

1997-01-01

The Ulysses spacecraft has been exploring the heliosphere since October 1990 in a six-year polar orbit. Despite varying operational demands, the pressure-fed monopropellant hydrazine reaction control system (RCS) has experienced few problems. The observed anomalies, having minimal operational impact, include plume impingement effects, electrical power overload effects and hydrazine gas generation effects. These anomalies are presented and discussed, with emphasis on the first observation of gas in the hydrazine propellant. The relatively low gas generation rate is attributed to: the use of high purity hydrazine; the configuration of the spin-stabilized spacecraft; the extensive use of titanium alloys; and the efficiency of the thermal control of the propellant tank which maintains a temperature of 21 C.

Insight into Hydrazinium Nitrates, Azides, Dicyanamide, and 5-Azidotetrazolate Ionic Materials from Simulations and Experiments

DTIC Science & Technology

2011-04-04

agreement between simulation and experiment is seen for UDMH , with simulations up to slightly above the boiling point of 336 K falling within a density ...conjunction wi th M05-2X density funct ional. Inclusion of a l one-pair on hydrazinium-based cations significantly improved ion electrostatic description...cation-anion complexes employing aug-cc- pvDz (cc-pvTz) basis functions at MP2 level or in conjunction with M05-2X density functional. Inclusion of

Investigation of Ignition Delay: Novel Beta-Substituted Ethylazide Derivatives as Potential New Liquid Propellant Fuels (Preprint)

DTIC Science & Technology

2007-04-09

Magnetic Resonance (NMR) Spectroscopy and Liquid atography ( LC ). Surprisingly the NMR shifts of the characteristic ethyl peaks were not pronounced .2 ppm...regardless of the conditions, UDMH and 2-chloroethyl azide did not react in H H N3 solven butylhy was re repeat and ch Chrom (only 0 group appear these m...unlike what one might expect from replacing a strong withdrawing group with a donating like an amine. In contrast, the peaks attributed to the

A Preliminary Study on the Use of the Ultraviolet Exhaust Plumes of the ICBMS for Launch Detection

DTIC Science & Technology

1986-11-01

HNO3) Ammonia (NH3) Nitrogen Ethyl Tetroxide (N204) Alcohol (C3HlOH) Chlorine Unsymmetrical Trifluoride Dimethylhydrazine (CIF3) (UDMH) (CHiNNHz) In the...attention recently is galium- aluminum - nitride (GaAIN). GaAlN is a photocathode material which is expected to have a significantly improved quantum...the possible combinations of these components. However, the most common solid fuel and oxidizer are aluminum powder and ammonium perchlorate (NH4ClO4

Environmental Quality Research, Use of Unicellular Algae for Evaluation of Potential Aquatic Contaminants

DTIC Science & Technology

1978-11-01

bioassays to determine the toxic and/or biostimulating effects of hydrazine and methylated hydrazines in various freshwater and marine aquatic environments...Table 2. TABLE 2 COMPOUNDS TESTED AND TEST CONDITIONS OF 1976/77 BIOASSAYS COMPOUND TEST CONDITIONS Type of Water Nutrient Level Hydrazine Freshwater ...AMRL-TR-78-86 ENVIRONMENTAL QUALITY RESEARCH, USE OF UNICELLULAR ALGAE FOR EVALUATION OF POTENTIAL AQUATIC CONTAMINANTS Third Annual Report JAN

The Role of Ammonia in the Metabolic Effects of Hydrazine.

DTIC Science & Technology

various experiments, various doses of hydrazine were given. The dogs given high doses developed hyperammonemia, respiratory alkalosis , coma and...The acute effects of administration of hydrazine on plasma ammonia, blood urea nitrogen, pH, pCO2, and respiratory rate were studied in dogs. In...convulsions. Relatively little change in blood urea nitrogen was found. Since brain function is adversely affected by hyperammonemia and alkalosis , it is

Simple and sensitive determination of hydrazine in drinking water by ultra-high-performance liquid chromatography-tandem mass spectrometry after derivatization with naphthalene-2,3-dialdehyde.

PubMed

Oh, Jin-Aa; Shin, Ho-Sang

2015-05-22

An ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method was developed to determine the level of hydrazine in drinking water. The method is based on the derivatization of hydrazine with naphthalene-2,3-dicarboxaldehyde (NDA) in water. The optimum conditions for UPLC-MS/MS detection were determined as follows: derivatization reagent dosage, 50mg/L of NDA; pH 2; and reaction time, 1min; room temperature. The formed derivative was injected into an LC system without extraction or purification procedures. Under the established conditions, the method was used to detect hydrazine in raw drinking water and chlorinated drinking water. The limits of detection and quantification for hydrazine in drinking water were 0.003μg/L and 0.01μg/L, respectively. The accuracy was in the range of 97-104%, and precision, expressed as relative standard deviation, was less than 9% in drinking water. Hydrazine was detected at a concentration of 0.13μg/L in one sample among 24 raw drinking water samples and in a range of 0.04-0.45μg/L in three samples among 24 chlorinated drinking water samples. Copyright © 2015 Elsevier B.V. All rights reserved.

Kaolinite-catalyzed air oxidation of hydrazine: Consideration of several compositional, structural and energetic factors in surface activation

NASA Technical Reports Server (NTRS)

Coyne, L. M.; Mariner, R.; Rice, A.

1991-01-01

Clay minerals have been shown to have numerous, curious, energetic properties by virtue of ultra-violet light release which can be triggered by gentle environmental changes such as wetting and dewetting by a variety of liquids, unique among them water and hydrazine. Since both water and hydrazine play multiple key roles in the air-oxidation of hydrazine on kaolinite surfaces, this reaction would seem to have prime potential for studying interrelationships of energy storage, release and chemical reactivity of clay surfaces, capacities basic to either the Bernal or Cairns-Smith roles of minerals in the origin of life. Establishment of the capacity for stored electronic energy to significantly alter surface chemistry is important, regardless of the reaction chosen to demonstrate it. Hydrazine air oxidation is overawingly complex, given the possibilities for step-wise control and monitoring of parameters. In the light of recently extended characterization of the kaolinite and model sheet catalysts we used to study hydrazine oxidation and gamma-irradiated silica, previous studies of hydrazine air-oxidation on aluminosilicate surfaces have been reevaluated. Our former conclusion remains intact that, whereas trace structural and surface contaminants do play some role in the catalysis of oxidation, they are not the only, nor even the dominant, catalytic centers. Initial intermediates in the oxidation can now be proposed which are consistent with production via O(-)-centers as well as ferric iron centers. The greater than square dependence of the initial reaction rate on the weight of the clay is discussed in the light of these various mechanistic possibilities.

Prototype Chemiluminescent Analyzer for Measurement of Hydrazines and Nitrogen Dioxide.

DTIC Science & Technology

1983-10-01

propellants, mono- methyihydrazine ( MMI ), 1,1-dimethy1hydrazine (UOMH), and hydrazine (Hz), as well as nitrogen dioxide (NO2 ). Preliminary studies at the USAF...large background readings, which consisted mainly of red and infrared (ir) radiation, were obtained in these instruments (2-5), optical filters were...used. This choice eliminated both the need for optical filters and the need to cool the PMTs (since bialkali tubes have much lower dark currents than

Biological effects of fuel and exhaust components from spacecraft descent engines employing hydrazine

NASA Technical Reports Server (NTRS)

Lehwalt, M. E.; Woeller, F. H.; Oyama, V. I.

1973-01-01

The effect of the products of the Viking terminal descent engine fuel upon possible extraterrestrial life at the Martian landing site is examined. The effects of the engine exhaust, the hydrazine fuel, and the breakdown products of the latter on terrestrial microorganisms have been studied. The results indicate that the gaseous exhaust products would probably not be hazardous to microorganisms, but that liquid hydrazine would be lethal.

Surface-catalyzed air oxidation reactions of hydrazines: Tubular reactor studies

NASA Technical Reports Server (NTRS)

Kilduff, Jan E.; Davis, Dennis D.; Koontz, Steven L.

1988-01-01

The surface-catalyzed air oxidation reactions of hydrazine, monomethylhydrazine, unsymmetrical dimethylhydrazine, symmetrical dimethylhydrazine, trimethylhydrazine and tetramethylhydrazine were investigated in a metal-powder packed turbular flow reactor at 55 plus or minus 3 C. Hydrazine was completely reacted on all surfaces studied. The major products of monomethylhydrazine (MMH) oxidation were methanol, methane and methyldiazene. The di-, tri- and tetra-methyl hydrazines were essentially unreactive under these conditions. The relative catalytic reactivities toward MMH are: Fe greater than Al2O3 greater than Ti greater than Zn greater than 316 SS greater than Cr greater than Ni greater than Al greater than 304L SS. A kinetic scheme and mechanism involving adsorption, oxidative dehydrogenation and reductive elimination reactions on a metal oxide surface are proposed.

Developing A New Sampling and Analysis Method for Hydrazine and Monomethyl Hydrazine

NASA Technical Reports Server (NTRS)

Allen, John R.

2002-01-01

Solid phase microextraction (SPME) will be used to develop a method for detecting monomethyl hydrazine (MMH) and hydrazine (Hz). A derivatizing agent, pentafluorobenzoyl chloride (PFBCl), is known to react readily with MMH and Hz. The SPME fiber can either be coated with PFBCl and introduced into a gaseous stream containing MMH, or PFBCl and MMH can react first in a syringe barrel and after a short equilibration period a SPME is used to sample the resulting solution. These methods were optimized and compared. Because Hz and MMH can degrade the SPME, letting the reaction occur first gave better results. Only MMH could be detected using either of these methods. Future research will concentrate on constructing calibration curves and determining the detection limit.

Electrocatalytic oxidation of hydrazine and hydroxylamine by graphene oxide-Pd nanoparticle-modified glassy carbon electrode.

PubMed

Lee, Eunhee; Kim, Daekun; You, Jung-Min; Kim, Seul Ki; Yun, Mira; Jeon, Seungwon

2012-12-01

Pd nanoparticle catalysts supported by thiolated graphene oxide (tGO) on a glassy carbon electrode (GCE), and denoted as tGO-Pd/GCE, are used in this study for the electrochemical determination of hydroxylamine and hydrazine. The physicochemical properties of tGO-Pd were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). They showed strong catalytic activity toward the oxidation of hydroxylamine and hydrazine. Cyclic voltammetry (CV) and amperometry were used to characterize the sensors' performances. The detection limits of hydroxylamine and hydrazine by tGO-Pd/GCE were 0.31 and 0.25 microM (s/n = 3), respectively. The sensors' sensitivity, selectivity, and stability were also investigated.

Hydrazine decomposition and other reactions

NASA Technical Reports Server (NTRS)

Armstrong, Warren E. (Inventor); La France, Donald S. (Inventor); Voge, Hervey H. (Inventor)

1978-01-01

This invention relates to the catalytic decomposition of hydrazine, catalysts useful for this decomposition and other reactions, and to reactions in hydrogen atmospheres generally using carbon-containing catalysts.

(6-bromo-1,4-dimethyl-9H-carbazol-3-yl-methylene)-hydrazine (carbhydraz) acts as a GPER agonist in breast cancer cells.

PubMed

Sinicropi, Maria Stefania; Lappano, Rosamaria; Caruso, Anna; Santolla, Maria Francesca; Pisano, Assunta; Rosano, Camillo; Capasso, Anna; Panno, Antonella; Lancelot, Jean Charles; Rault, Sylvain; Saturnino, Carmela; Maggiolini, Marcello

2015-01-01

Estrogens control a wide number of aspects of human physiology and play a key role in multiple diseases, including cancer. Estrogens act by binding to and activating the cognate receptor (ER), however numerous studies have revealed that the G protein-coupled receptor named GPR30/GPER mediates also estrogen signals. As ER and GPER share the ability to bind to same compounds, the use of GPER-selective ligands has allowed a better understanding of the biological responses mediated by GPER. In the present study, we designed and synthesized two novel carbazole derivatives and then investigated their ability to interact with and activate the GPER-mediated transduction pathway in breast cancer cells. Both compounds did not activate the classical ER in MCF7 cells, whereas one of the two compounds synthesized triggered through GPER the rapid ERK activation in ER-negative SkBr3 cells, demonstrating a good affinity for GPER in docking studies. The characterization of this novel selective GPER agonist could represent a potential useful tool to provide further insights into the physiopathological role exerted by GPER.

Performance Characteristics of a DME Propellant Arcjet Thruster

NASA Astrophysics Data System (ADS)

Kakami, Akira; Beeppu, Shinji; Maiguma, Muneyuki; Tachibana, Takeshi

This paper describes the influence of cathode configuration on performance of an arcjet thruster using dimethyl ether (DME) propellant. DME, an ether compound, has suitable characteristics for a space propulsion system; DME is storable in a liquid state without being kept under a high pressure, and requires no sophisticated temperature management such as a cryogenic device. DME can be gasified and liquefied simply by adjusting temperature whereas hydrazine, a conventional propellant, requires an iridium-based particulate catalyst for its gasification. In this study, thrust of a 1-kW class DME arcjet thruster is measured at a discharge current of 13 A, DME mass flow rates ranging 15 to 60 mg/s under three cathode configurations: flat-tip rods of 2 and 4 mm in diam. and 4-mm-diam. rod having a cavity of 2 mm in diameter. Thrust measurements show that thrust is increased with propellant mass flow rate. Among the tested cathodes, the flat-tip rod of 4 mm in diam. with 55 mg/s DME flow rate yielded the highest performance: specific impulse of 330 s, thrust of 0.18 N, discharge power of 1400 W and specific power of 25 MJ/kg.

Dose response study of conjugated fatty acid derived from safflower oil on mammary and colon carcinogenesis pretreated with 7,12-dimethylbenz[a]anthracene (DMBA) and 1,2-dimethylhydrazine (DMH) in female Sprague-Dawley rats.

PubMed

Cheng, Jing Lei; Futakuchi, Mitsuru; Ogawa, Kumiko; Iwata, Toshio; Kasai, Masaaki; Tokudome, Shinkan; Hirose, Masao; Shirai, Tomoyuki

2003-07-10

To clarify the chemopreventive effects of conjugated fatty acid derived from safflower oil (CFA-S), rich in conjugated linoleic acid (CLA), on mammary and colon carcinogenesis, 6 week old female Sprague-Dawley (SD) rats received diet containing 0.01, 0.05, 0.1, 1, or 2% CFA-S subsequent to five times subcutaneous injections of 1,2-dimethyl-hydrazine (DMH) at a dose of 40 mg/kg b.w. and a single 50 mg/kg b.w. intragastric application of 7,12-dimethylbenz[a]anthracene (DMBA) during the first 11 days. The experiment was terminated at week 36. Numbers of mammary tumors, colon aberrant crypt foci (ACF), and proliferative indices of mammary tumors, and colon epithelium were analyzed. The 1% dose was found to be optimal for suppression of carcinogenesis in both target organs, a good correlation being noted with between data for cell proliferation. These results suggest that a diet containing appropriate levels of CFA-S may be useful for prevention of mammary and colon cancer.

Simultaneous quantitation of hydrazine and acetylhydrazine in human plasma by high performance liquid chromatography-tandem mass spectrometry after derivatization with p-tolualdehyde.

PubMed

Song, Lu; Gao, Dan; Li, Shangfu; Wang, Yanwei; Liu, Hongxia; Jiang, Yuyang

2017-09-15

A high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) method was developed for simultaneous quantitative analysis of hydrazine and acetylhydrazine in human plasma based on the strategy of p-tolualdehyde derivatization. The derivatization reactions were easily realized by ultrasonic manipulation for 40min. Good separation of the derivatization products was achieved using a C 18 column by gradient elution. The optimized mass transition ion-pairs (m/z) monitored for the two hydrazine derivatives were m/z 237.1≫>119.9 and m/z 176.9≫>117.8, respectively. The limit of detection (LOD) and limit of quantification (LOQ) for hydrazine were 0.002 and 0.005ngmL -1 separately. And they were 0.03 and 0.05ngmL -1 for acetylhydrazine, respectively. The linear range was 0.005-50ngmL -1 for hydrazine and 0.05-500ngmL -1 for acetylhydrazine with R 2 greater than 0.999. The recovery range was determined to be 95.38-108.12% with the relative standard deviation (RSD) in the range of 1.24-14.89%. The method was successfully applied to detect 30 clinical plasma samples of pulmonary tuberculosis patients treated with isoniazid. The concentrations were from 0.04-1.99ngmL -1 for hydrazine and 0.06-142.43ngmL -1 for acetylhydrazine. The results indicated that our developed method had the potential for the detection of hydrazine toxicology in complex biological samples. Furthermore, the method has an important significance to clinical treatment with drugs. Copyright © 2017. Published by Elsevier B.V.

Thermochemical and Kinetics of Hydrazine Dehydrogenation by an Oxygen Atom in Hydrazine-Rich Systems: A Dimer Model.

PubMed

Spada, Rene F K; Ferrão, Luiz F A; Roberto-Neto, Orlando; Lischka, Hans; Machado, Francisco B C

2015-12-24

The kinetics of the reaction of N2H4 with oxygen depends sensitively on the initial conditions used. In oxygen-rich systems, the rate constant shows a conventional positive temperature dependence, while in hydrazine-rich setups the dependence is negative in certain temperature ranges. In this study, a theoretical model is presented that adequately reproduces the experimental results trend and values for hydrazine-rich environment, consisting of the hydrogen abstraction from the hydrazine (N2H4) dimer by an oxygen atom. The thermochemical properties of the reaction were computed using two quantum chemical approaches, the coupled cluster theory with single, double, and noniterative triple excitations (CCSD(T)) and the M06-2X DFT approach with the aug-cc-pVTZ and the maug-cc-pVTZ basis sets, respectively. The kinetic data were calculated with the improved canonical variational theory (ICVT) using a dual-level methodology to build the reaction path. The tunneling effects were considered by means of the small curvature tunneling (SCT) approximation. Potential wells on both sides of the reaction ((N2H4)2 + O → N2H4···N2H3 + OH) were determined. A reaction path with a negative activation energy was found leading, in the temperature range of 250-423 K, to a negative dependence of the rate constant on the temperature, which is in good agreement with the experimental measurements. Therefore, the consideration of the hydrazine dimer model provides significantly improved agreement with the experimental data and should be included in the mechanism of the global N2H4 combustion process, as it can be particularly important in hydrazine-rich systems.

Sustained load crack growth design data for Ti-6Al-4V titanium alloy tanks containing hydrazine

NASA Technical Reports Server (NTRS)

Lewis, J. C.; Kenny, J. T.

1976-01-01

Sustained load crack growth data for Ti-6Al-4V titanium alloy in hydrazine per MIL-P-26536 and refined hydrazine are presented. Fracture mechanics data on crack growth thresholds for heat-treated forgings, aged and unaged welds, and aged and unaged heat-affected zones are reported. Fracture mechanics design curves of crack growth threshold stress intensity versus temperature are generated from 40 to 71 C.

Chronic Inhalation Toxicity of Hydrazine: Oncogenic Effects

DTIC Science & Technology

1981-06-01

AFAMRL-TR-81-56 CHRONIC INHALATION TOXICITY OF HYDRAZINE: ONCOGENIC EFFECTS J. D. MacEWEN E. H. VERNOT C C HAUN L . R. KINKEAD UNIVERSITY OF...Acknowledgement is made to A. K. Roychowdhury, Ph.D., J. D. Diaz, G. L . Fogle, Maj. R. Amster and J. A. Sizemore for their significant contributions and...Hemoglobin (g %) for Dogs Exposed to Hydrazine for One Year 49 24 Group Mean Values ± Standard Deviations of Sodium (mEq/ L ) for Dogs Exposed to

Long life monopropellant hydrazine thruster evaluation for Space Station Freedom application

NASA Technical Reports Server (NTRS)

Popp, Christopher G.; Henderson, John B.

1991-01-01

In support of propulsion system thruster development activity for Space Station Freedom (SSF), NASA Johnson Space Center (JSC) is conducting a hydrazine thruster technology demonstration program. The goal of this program is to identify impulse life capability of state-of-the-art long life hydrazine thrusters nominally rated for 50 pounds thrust at 300 psia supply pressure. The SSF propulsion system requirement for impulse life of this thruster class is 1.5 million pound-seconds, corresponding to a throughput of approximately 6400 pounds of propellant, with a high performance (234 pound-seconds per propellant pound). Long life thrusters were procured from Hamilton Standard, The Marquardt Company, and Rocket Research Company. Testing has initiated on the thruster designs to identify life while simulating expected thruster firing duty cycles and durations for SSF using monopropellant grade hydrazine. This paper presents a review of the SSF propulsion system and requirements as applicable to hydrazine thrusters, the three long life thruster designs procured by JSC and the resultant acceptance test data for each thruster, and the JSC test plan and facility.

Catalytic transformation of dinitrogen into ammonia and hydrazine by iron-dinitrogen complexes bearing pincer ligand

PubMed Central

Kuriyama, Shogo; Arashiba, Kazuya; Nakajima, Kazunari; Matsuo, Yuki; Tanaka, Hiromasa; Ishii, Kazuyuki; Yoshizawa, Kazunari; Nishibayashi, Yoshiaki

2016-01-01

Synthesis and reactivity of iron-dinitrogen complexes have been extensively studied, because the iron atom plays an important role in the industrial and biological nitrogen fixation. As a result, iron-catalyzed reduction of molecular dinitrogen into ammonia has recently been achieved. Here we show that an iron-dinitrogen complex bearing an anionic PNP-pincer ligand works as an effective catalyst towards the catalytic nitrogen fixation, where a mixture of ammonia and hydrazine is produced. In the present reaction system, molecular dinitrogen is catalytically and directly converted into hydrazine by using transition metal-dinitrogen complexes as catalysts. Because hydrazine is considered as a key intermediate in the nitrogen fixation in nitrogenase, the findings described in this paper provide an opportunity to elucidate the reaction mechanism in nitrogenase. PMID:27435503

Developing a New Sampling And Analysis Method For Hydrazine And Monomethyl Hydrazine: Using a Derivatizing Agent With Solid Phase Microextraction

NASA Technical Reports Server (NTRS)

Allen, John

2001-01-01

Solid phase microextraction (SPME) will be used to develop a method for detecting monomethyl hydrazine (MMH) and hydrazine (Hz). A derivatizing agent, pentafluorobenzoyl chloride (PFBCI), is known to react readily with MMH and Hz. The SPME fiber can either be coated with PFBCl and introduced into a gaseous stream containing MMH, or PFBCl and MMH can react first in a syringe barrel and after a short equilibration period a SPME is used to sample the resulting solution. These methods were optimized and compared. Because Hz and MMH can degrade the SPME, letting the reaction occur first gave better results. Only MMH could be detected using either of these methods. Future research will concentrate on constructing calibration curves and determining the detection limit.

Hydrazine-induced post-chemiluminescence phenomenon of permanganate-luminol reaction and its applications.

PubMed

Du, Jianxiu; Lu, Jiuru

2004-01-01

The post-chemiluminescence phenomenon arising from the permanganate-luminol reaction induced by hydrazine and isoniazid was investigated. When hydrazine or isoniazid was injected into the mixture after the end of the reaction of permanganate with alkaline luminol, a new chemiluminescence (CL) reaction was initiated and strong CL signal was detected. A possible CL mechanism is suggested, based upon the studies of the kinetic characteristics of the CL reaction, the UV-visible spectra, the CL spectra and some other experiments. The present reactions allow the determination of 0.1-10.0 mg/L hydrazine and 0.02-1.0 mg/L isoniazid, with detection limits of 0.03 mg/L and 0.006 mg/L, respectively. The method was applied to the determination of isoniazid in pharmaceutical preparations.

Synthesis, characterization and antioxidant study of N,N’-bis(2-chlorobenzamidothiocarbonyl)hydrazine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Firdausiah, Syadza; Hasbullah, Siti Aishah; Yamin, Bohari M.

2015-09-25

N,N’-bis(2-chlorobenzamidothiocarbonyl)hydrazine was synthesized from 2-chlorobenzoylisothiocyanate and hydrazine in acetone. The compound was characterized by infrared, {sup 1}H and {sup 13}C NMR, and UV-Vis spectroscopies. X-ray crystallography study showed the molecule adopt trans configuration at both N-N and C-N bonds. The compound showed high antioxidant activity, EC{sub 50} of 374.89 µM, compared to ascorbic acid (EC{sub 50} of 561.36 µM)

Hydrazine Sulfate (PDQ®)—Patient Version

Cancer.gov

Expert-reviewed information summary about the use of hydrazine sulfate as a treatment for people with cancer. Note: The information in this summary is no longer being updated and is provided for reference purposes only.

Effect of pressure on rate of burning /decomposition with flame/ of liquid hydrazine.

NASA Technical Reports Server (NTRS)

Antoine, A. C.

1966-01-01

Liquid hydrazine decomposition process to determine what chemical or physical changes may be occurring that cause breaks in burning rate/ pressure curves, measuring flame temperature and light emission

Review of Alpha-Ketoglutaric Acid (AKGA) Hydrazine and Monomethylhydrazine (MMH) Neutralizing Compound

NASA Technical Reports Server (NTRS)

Dibbern, Andreas W.; Beeson, Harold D.; Greene, Benjamin; Giordano, Thomas J.

2009-01-01

The Johnson Space Center (JSC) White Sands Test Facility (WSTF) and NASA Engineering and Safety Center (NESC) were requested by NASA Associate Administrator for Space Operations to perform an evaluation of a proposed hydrazine/monomethylhydrazine (MMH) fuel treatment method using alpha-ketoglutaric acid (AKGA). This evaluation request was prompted by preliminary tests at the Kennedy Space Center (KSC), suggesting cost and operational benefits to NASA for the Space Shuttle Program (SSP) and other hardware decontamination and decommissioning, in addition to hydrazine and MMH waste treatment activities. This paper provides the team's position on the current KSC and New Mexico Highlands University (NMHU) efforts toward implementing the AKGA treatment technology with flight hardware, ground support equipment (GSE), hydrazine and MMH spills, and vapor control. This evaluation is current to the last data examined (approximately September 2008).

Worldwide Space Launch Vehicles and Their Mainstage Liquid Rocket Propulsion

NASA Technical Reports Server (NTRS)

Rahman, Shamim A.

2010-01-01

Space launch vehicle begins with a basic propulsion stage, and serves as a missile or small launch vehicle; many are traceable to the 1945 German A-4. Increasing stage size, and increasingly energetic propulsion allows for heavier payloads and greater. Earth to Orbit lift capability. Liquid rocket propulsion began with use of storable (UDMH/N2O4) and evolved to high performing cryogenics (LOX/RP, and LOX/LH). Growth versions of SLV's rely on strap-on propulsive stages of either solid propellants or liquid propellants.

Chemical and Molecular Biological Aspects of Alkylhydrazine-Induced Carcinogenesis in Human Cells in Vitro

DTIC Science & Technology

1980-09-01

methylazozy- methanol acetate ( MAMA ), proved to be a potent transformer as well as a carcinogen. The obvious conclusion is that the human cell culture...Negative MMH 62 pg/ml Negative [ AOM Negative at 100 1g/ml Not tested MAMA 3.6 ug/ml 900 2/16’ Tetrazine 50 Ug/ml Positive. No data yet. [j Phenylhydrazine...the tumor incidence data for MAMA is not com-B parable to those of UDMH and Hz. I 11-% C. Conclusion: In our attempts,to correlate toxicity and/or

Hydrazine reduction of transition metal oxides - In situ characterization using X-ray photoelectron spectroscopy

NASA Technical Reports Server (NTRS)

Littrell, D. M.; Tatarchuk, B. J.

1986-01-01

The transition metal oxides (TMOs) V2O5, FeO3, Co3O4, NiO, CuO, and ZnO were exposed to hydrazine at various pressures. The metallic surfaces were surveyed by in situ X-ray photoelectron spectroscopy to determine the irrelative rate of reduction by hydrazine. The most easily reducible oxide, CuO, could be reduced to the metallic state at room temperature and 10 to the -6th torr. The reaction is first order with respect to CuO, with an activation energy of about 35 kJ/mol. Two types of adsorption were seen to occur at 295 K: (1) a reversible component in which the measured N:Cu ratio increased to 0.60 at hydrazine pressures up to 0.5 torr, and (2) an irreversible component, with a N:Cu ratio of 0.28, which could not be removed by extended vacuum pumping. The results of this study are useful for the identification of TMO's that can be used as solid neatallizers of hydrazine spills, and for the preparation of metal surfaces for electroplating and evaporative thin-film coating.

ATS-F radiant cooler contamination test in a hydrazine thruster exhaust

NASA Technical Reports Server (NTRS)

Chirivella, J. E.

1973-01-01

A test was conducted under simulated space conditions to determine the potential thermal degradation of the ATS-F radiant cooler from any contaminants generated by a 0.44-N(0.1-lbf) hydrazine thruster. The radiant cooler, a 0.44-N(0.1-lbf)hydrazine engine, and an aluminum plate simulating the satellite interface were assembled to simulate their flight configuration. The cooler was provided with platinum sensors for measuring temperature, and its surfaces were instrumented with six quartz crystal microbalance units (QCM) to measure contaminant mass deposits. The complete assembly was tested in the molecular sink vacuum facility (Molsink) at the Jet Propulsion Laboratory. This was the first time that a radiant cooler and a hydrazine engine were tested together in a very-high-vacuum space simulator, and this test was the first successful measurement of detectable deposits from hydrazine rocket engine plumes in a high vacuum. The engine was subjected to an accelerated duty cycle of 1 pulse/min, and after 2-hr of operation, the QCMs began to shift in frequency. The tests continued for several days and, although there was considerable activity in the QCMs, the cooler never experienced thermal degradation.

Occupational safety considerations with hydrazine

NASA Technical Reports Server (NTRS)

Clewell, Harvey J., III; Mcdougal, James N.; George, Marilyn E.; Andersen, Melvin E.

1992-01-01

Hydrazine is a reducing agent that is most commonly used as a propellant and as an oxygen scavenger in boilers. Hydrazine is extremely irritating and has been demonstrated to produce both acute and chronic toxicity. As a result, the established permissible inhalation exposure limits are very low, and respiration protection is required whenever vapors are present. Liquid hydrazine penetrates the skin and produces a chemical burn; therefore, some protective measures must also be taken to protect the skin from liquid contact. Often, however, a cumbersome, whole-body protective suit is worn to protect against skin contact with vapor as well. To what extent it is actually necessary to protect skin from vapor penetration had not previously been demonstrated. In an attempt to answer this question, we conducted a study with rats to compare the dermal penetration of hydrazine vapor with inhalation. Pharmacokinetic modeling was used to compare body burdens resulting from these different routes of exposure. The analysis concluded that the vapor concentration during a skin-only exposure would have to be at least 200 times higher than that during inhalation to achieve the same body burden. This type of estimation illustrates the use of predictive toxicology in occupational exposures.

Attitude Control Propulsion Components, Volume 2

NASA Technical Reports Server (NTRS)

1974-01-01

Attitude control propulsion components are described, including hydrazine thrusters, hydrazine thruster and cold gas jet valves, and pressure and temperature transducers. Component-ordered data are presented in tabular form; the manufacturer and specific space program are included.

Hydrazine Sulfate (PDQ®)—Health Professional Version

Cancer.gov

Expert-reviewed information summary about the use of hydrazine sulfate as a treatment for people with cancer. Note: The information in this summary is no longer being updated and is provided for reference purposes only.

Long-time dynamic compatibility of elastomeric materials with hydrazine

NASA Technical Reports Server (NTRS)

Coulbert, C. D.; Cuddihy, E. F.; Fedors, R. F.

1973-01-01

The tensile property surfaces for two elastomeric materials, EPT-10 and AF-E-332, were generated in air and in liquid hydrazine environments using constant strain rate tensile tests over a range of temperatures and elongation rates. These results were used to predict the time-to-rupture for these materials in hydrazine as a function of temperature and amount of strain covering a span of operating times from less than a minute to twenty years. The results of limited sheet-folding tests and their relationship to the tensile failure boundary are presented and discussed.

Preparation of 3,5-disubstituted pyrazoles and isoxazoles from terminal alkynes, aldehydes, hydrazines, and hydroxylamine.

PubMed

Harigae, Ryo; Moriyama, Katsuhiko; Togo, Hideo

2014-03-07

The reaction of terminal alkynes with n-BuLi, and then with aldehydes, followed by the treatment with molecular iodine, and subsequently hydrazines or hydroxylamine provided the corresponding 3,5-disubstituted pyrazoles or isoxazoles in good yields with high regioselectivity, through the formations of propargyl secondary alkoxides and α-alkynyl ketones. The present reactions are one-pot preparation of 3,5-disubstituted pyrazoles from terminal alkynes, aldehydes, molecular iodine, and hydrazines, and 3,5-disubstituted isoxazoles from terminal alkynes, aldehydes, molecular iodine, and hydroxylamine.

Interactions of Hydrazine and of Hydrazine Derivatives with Soil Constituents and with Soils.

DTIC Science & Technology

1982-01-31

exchangeable metal cations held by the clay and humic colloids, or the metal of the hydrous oxide colloids. The pH values of the natural soil solution of most...hydrazine into a soil system will tend to increase the pH of the soil solution . Hydrous oxides of iron and aluminium are insoluble at high pH, and these...aeration, and by the soil solution pH. Treatment of contaminated soils can alter these properties in order to promote the degradation or immobilization of

Wipes, Coatings, and Patches for Detecting Hydrazines

NASA Technical Reports Server (NTRS)

Young, Rebecca; Buttner, William

2005-01-01

Three color-indicating devices have been conceived as simple, rapid, inexpensive means of detecting hazardous liquid and gaseous substances in settings in which safety is of paramount concern and it would be too time-consuming or otherwise impractical to perform detection by use of such instruments as mass spectrometers. More specifically, these devices are designed for detecting hypergolic fuels (in particular, hydrazines) and hypergolic oxidizers in spacecraft settings, where occasional leakage of these substances in liquid or vapor form occurs and it is imperative to take early corrective action to minimize adverse health effects. With suitable redesign, including reformulation of their color indicator chemicals, these devices could be adapted to detection of other hazardous substances in terrestrial settings (e.g., industrial and military ones). One of the devices is a pad of a commercially available absorbent material doped with a color indicator. The absorbent material is made from 70 percent polyester and 30 percent nylon and can absorb about eight times its own weight of liquid. The color indicator is a mixture of conventional pH color indicator chemicals. Hydrazine and monomethyl hydrazine, which are basic, cause the color indicator to turn green. In the original intended application, the pad is wiped on a space suit that is suspected of having been exposed to leaking monomethyl hydrazine during a space walk, before the wearer returns to the interior of the spacecraft. If the wiped surface is contaminated with hydrazine, the pad turns green. In addition, the pad absorbs hydrazine from the wiped surface, thereby reducing or eliminating the hazard. Used pads, including ones that show contamination by hydrazine, can be stored in a sealed plastic bag for subsequent disposal. The second device, which has been proposed but not yet developed, would comprise a color indicator material in the form of either a coating on a space suit (or other protective garment) or a coating on a sheet that could be easily attached to and detached from the protective garment. The coating material would be a hydrogel doped with a suitable pH indicator. The hydrogel would also serve to maintain a level of moisture needed to support the chemical reaction mentioned in the next sentence. In addition to changing color to indicate the presence of any hypergolic fuel (which is basic) or hypergolic oxidizer (which is acidic) that might splash on the space suit, the pH indicator would also react with the hypergolic fuel or oxidizer and thereby bind it. The third device is a color dosimeter for detecting hydrazine liquid or vapor coming from microscopic leaks. This device is designed to satisfy several requirements specific to its original intended use in the auxiliary power unit of the space shuttle. These requirements include stability under vacuum, stability at moderate temperature, fast and irreversible change in color upon exposure to hydrazine, and visibility of the color change through polyimide tape.

Monopropellant hydrazine resistoject: Engineering model fabrication and test task

NASA Technical Reports Server (NTRS)

Murch, C. K.

1973-01-01

The monopropellant hydrazine resistojet, termed the electrothermal hydrazine thruster (EHT) by TRW systems, thermally decomposes anhydrous hydrazine propellant to produce a high-temperature, low-molecular-weight gas for expulsion through a propulsive nozzle. The EHT developed for this program required about 3-5 watts of electrical power and produced 0.020 to 0.070 pound of thrust over the inlet pressure range of 100 to 400 psia. The thruster was designed for both pulsed and steady state operation. A summary of the GSFC original requirements and GSFC modified requirements, and the performance of the engineering model EHT is given. The experimental program leading to the engineering model EHT design, modifications necessary to achieve the required thruster life capability, and the results of the life test prgram. Other facets of the program, including analyses, preliminary design, specifications, data correlation, and recommendations for a flight model are discussed.

A Portable Electronic Nose For Hydrazine and Monomethyl Hydrazine Detection

NASA Technical Reports Server (NTRS)

Young, Rebecca C.; Linnell, Bruce R.; Peterson, Barbara V.; Brooks, Kathy B.; Griffin, Tim P.

2004-01-01

The Space Program and military use large quantities Hydrazine (Hz) and monomethyl hydrazine (MMI-I) as rocket propellant. These substances are very toxic and are suspected human carcinogens. The American Conference of Governmental Industrial Hygienist set the threshold limit value to be 10 parts per billion (ppb). Current off-the-shelf portable instruments require 10 to 20 minutes of exposure to detect 10 ppb concentration. This shortcofriing is not acceptable for many operations. A new prototype instrument using a gas sensor array and pattern recognition software technology (i.e., an electronic nose) has demonstrated the ability to identify either Hz or MM}{ and quantify their concentrations at 10 parts per billion in 90 seconds. This paper describes the design of the portable electronic nose (e-nose) instrument, test equipment setup, test protocol, pattern recognition algorithm, concentration estimation method, and laboratory test results.

Regeneration of ammonia borane from polyborazylene

DOEpatents

Sutton, Andrew; Gordon, John C; Ott, Kevin C; Burrell, Anthony K

2013-02-05

Method of producing ammonia borane, comprising providing a reagent comprising a dehydrogenated material in a suitable solvent; and combining the reagent with a reducing agent comprising hydrazine, a hydrazine derivative, or combinations thereof, in a reaction which produces a mixture comprising ammonia borane.

The development of a non-cryogenic nitrogen/oxygen supply system. [using hydrazine/water electrolysis

NASA Technical Reports Server (NTRS)

Greenough, B. M.; Mahan, R. E.

1974-01-01

A hydrazine/water electrolysis process system module design was fabricated and tested to demonstrate component and module performance. This module is capable of providing both the metabolic oxygen for crew needs and the oxygen and nitrogen for spacecraft leak makeup. The component designs evolved through previous R and D efforts, and were fabricated and tested individually and then were assembled into a complete module which was successfully tested for 1000 hours to demonstrate integration of the individual components. A survey was made of hydrazine sensor technology and a cell math model was derived.

The effect of hydrazine intercalation on the structure and capacitance of 2D titanium carbide (MXene)

DOE PAGES

Mashtalir, O.; Lukatskaya, Maria R.; Kolesnikov, Alexander I.; ...

2016-03-25

Herein we show that hydrazine intercalation into 2D titanium carbide (Ti 3C 2-based MXene) results in changes in its surface chemistry by decreasing the amounts of fluorine, OH surface groups and intercalated water. It also creates a pillaring effect between Ti 3C 2T x layers pre-opening the structure and improving the accessability to active sites. Furthermore, the hydrazine treated material has demonstrated a greatly improved capacitance of 250 F g –1 in acidic electrolytes with an excellent cycling ability for electrodes as thick as 75 μm.

Hypergolic fuel detection using individual single walled carbon nanotube networks

NASA Astrophysics Data System (ADS)

Desai, S. C.; Willitsford, A. H.; Sumanasekera, G. U.; Yu, M.; Tian, W. Q.; Jayanthi, C. S.; Wu, S. Y.

2010-06-01

Accurate and reliable detection of hypergolic fuels such as hydrazine (N2H4) and its derivatives is vital to missile defense, aviation, homeland security, and the chemical industry. More importantly these sensors need to be capable of operation at low temperatures (below room temperature) as most of the widely used chemical sensors operate at high temperatures (above 300 °C). In this research a simple and highly sensitive single walled carbon nanotube (SWNT) network sensor was developed for real time monitoring of hydrazine leaks to concentrations at parts per million levels. Upon exposure to hydrazine vapor, the resistance of the air exposed nanotubes (p-type) is observed to increase rapidly while that of the vacuum-degassed nanotubes (n-type) is observed to decrease. It was found that the resistance of the sample can be recovered through vacuum pumping and exposure to ultraviolet light. The experimental results support the electrochemical charge transfer mechanism between the oxygen redox couple of the ambient and the Fermi level of the SWNT. Theoretical results of the hydrazine-SWNT interaction are compared with the experimental observations. It was found that a monolayer of water molecules on the SWNT is necessary to induce strong interactions between hydrazine and the SWNT by way of introducing new occupied states near the bottom of the conduction band of the SWNT.

Hydrazine and hydroxylamine as probes for O2-reduction site of mitochondrial cytochrome c oxidase.

PubMed Central

Kubota, T; Yoshikawa, S

1993-01-01

Reactions of hydrazine and hydroxylamine with bovine heart cytochrome c oxidase in the fully reduced state were investigated under anaerobic conditions following the visible-Soret spectral change. Hydrazine gave a sharp band at 575 nm with 20% decrease in the alpha band at 603 nm, and hydroxylamine induced a 2 nm blue-shift for the alpha band without any clear splitting. The Soret band at 443 nm was decreased significantly in intensity, with the concomitant appearance of a shoulder with hydrazine or a peak with hydroxylamine, both near 430 nm. The dependence on pH of the affinity of these reagents for the enzyme indicates that only the deprotonated forms of these reagents bind to the enzyme, suggesting a highly hydrophobic environment of the haem ligand-biding site. These spectral changes were largely removed by addition of cyanide or CO. However, detailed analysis of these spectral changes indicates that hydrazine perturbs the shape of the spectral change induced by cyanide and hydroxylamine perturbs that induced by CO. These results suggest that these aldehyde reagents bind to haem a3 iron as well as to a second site which is most likely to be the formyl group on the haem periphery, and that these two sites bind these reagents anti-cooperatively with each other. PMID:8389138

Hydrazine-induced thermo-reversible optical shifts in silver-gelatin bionanocomposites

NASA Astrophysics Data System (ADS)

Aimé, Carole; Rietveld, Ivo B.; Coradin, Thibaud

2011-03-01

Bionanocomposites formed by in situ growth of silver nanoparticles within gelatin gels exhibit large (up to 100 nm) thermo-reversible optical shifts resulting from the enhancement of gel matrix scattering by the interaction of the biopolymer with the hydrazine reducing agent.

Key role of hydrazine to the interaction between oxaloacetic against phosphoenolpyruvic carboxykinase (PEPCK): ONIOM calculations.

PubMed

Prajongtat, Pongthep; Phromyothin, Darinee Sae-Tang; Hannongbua, Supa

2013-08-01

The interactions between oxaloacetic (OAA) and phosphoenolpyruvic carboxykinase (PEPCK) binding pocket in the presence and absence of hydrazine were carried out using quantum chemical calculations, based on the two-layered ONIOM (ONIOM2) approach. The complexes were partially optimized by ONIOM2 (B3LYP/6-31G(d):PM6) method while the interaction energies between OAA and individual residues surrounding the pocket were performed at the MP2/6-31G(d,p) level of theory. The calculated interaction energies (INT) indicated that Arg87, Gly237, Ser286, and Arg405 are key residues for binding to OAA with the INT values of -1.93, -2.06, -2.47, and -3.16 kcal mol(-1), respectively. The interactions are mainly due to the formation of hydrogen bonding interactions with OAA. Moreover, using ONIOM2 (B3LYP/6-31G(d):PM6) applied on the PEPCKHS complex, two proton transfers were observed; first, the proton was transferred from the carboxylic group of OAA to hydrazine while the second one was from Asp311 to Lys244. Such reactions cause the generation of binding strength of OAA to the pocket via electrostatic interaction. The orientations of Lys243, Lys244, His264, Asp311, Phe333, and Arg405 were greatly deviated after hydrazine incorporation. These indicate that hydrazine plays an important role in terms of not only changing the conformation of the binding pocket, but is also tightly bound to OAA resulting in its conformation change in the pocket. The understanding of such interaction can be useful for the design of hydrazine-based inhibitor for antichachexia agents.

Ursolic acid and oleanolic acid suppress preneoplastic lesions induced by 1,2-dimethylhydrazine in rat colon.

PubMed

Furtado, Ricardo A; Rodrigues, Erlon P; Araújo, Felipe R R; Oliveira, Wendel L; Furtado, Michelle A; Castro, Márcio B; Cunha, Wilson R; Tavares, Denise C

2008-06-01

Ursolic acid (UA) and oleanolic acid (OA) are pentacyclic triterpenoid compounds found in plants used in the human diet and in medicinal herbs, in the form of aglycones or as the free acid. These compounds are known for their hepatoprotective, anti-inflammatory, antimicrobial, hypoglycemic, antimutagenic, antioxidant, and antifertility activities. In the present study, we evaluated the effects of UA and OA on the formation of 1,2-dimethyl-hydrazine (DMH)-induced aberrant crypt foci (ACF) in the colon of the male Wistar rat. The animals received subcutaneous (sc) injections of DMH (40 mg/kg body weight) twice a week for two weeks to induce ACF. UA, OA and a mixture of UA and OA were administered to the rats five times a week for four weeks by gavage at doses of 25 mg/kg body weight/day each, during and after DMH treatment. All animals were sacrificed in week 5 for the evaluation of ACF. The results showed a significant reduction in the frequency of ACF in the group treated with the triterpenoid compounds plus DMH when compared to those treated with DMH alone, suggesting that UA and OA suppress the formation of ACF and have a protective effect against colon carcinogenesis.

Efficient hydrogen evolution in transition metal dichalcogenides via a simple one-step hydrazine reaction

PubMed Central

Cummins, Dustin R.; Martinez, Ulises; Sherehiy, Andriy; Kappera, Rajesh; Martinez-Garcia, Alejandro; Schulze, Roland K.; Jasinski, Jacek; Zhang, Jing; Gupta, Ram K.; Lou, Jun; Chhowalla, Manish; Sumanasekera, Gamini; Mohite, Aditya D.; Sunkara, Mahendra K.; Gupta, Gautam

2016-01-01

Hydrogen evolution reaction is catalysed efficiently with precious metals, such as platinum; however, transition metal dichalcogenides have recently emerged as a promising class of materials for electrocatalysis, but these materials still have low activity and durability when compared with precious metals. Here we report a simple one-step scalable approach, where MoOx/MoS2 core-shell nanowires and molybdenum disulfide sheets are exposed to dilute aqueous hydrazine at room temperature, which results in marked improvement in electrocatalytic performance. The nanowires exhibit ∼100 mV improvement in overpotential following exposure to dilute hydrazine, while also showing a 10-fold increase in current density and a significant change in Tafel slope. In situ electrical, gate-dependent measurements and spectroscopic investigations reveal that hydrazine acts as an electron dopant in molybdenum disulfide, increasing its conductivity, while also reducing the MoOx core in the core-shell nanowires, which leads to improved electrocatalytic performance. PMID:27282871

Efficient hydrogen evolution in transition metal dichalcogenides via a simple one-step hydrazine reaction.

PubMed

Cummins, Dustin R; Martinez, Ulises; Sherehiy, Andriy; Kappera, Rajesh; Martinez-Garcia, Alejandro; Schulze, Roland K; Jasinski, Jacek; Zhang, Jing; Gupta, Ram K; Lou, Jun; Chhowalla, Manish; Sumanasekera, Gamini; Mohite, Aditya D; Sunkara, Mahendra K; Gupta, Gautam

2016-06-10

Hydrogen evolution reaction is catalysed efficiently with precious metals, such as platinum; however, transition metal dichalcogenides have recently emerged as a promising class of materials for electrocatalysis, but these materials still have low activity and durability when compared with precious metals. Here we report a simple one-step scalable approach, where MoOx/MoS2 core-shell nanowires and molybdenum disulfide sheets are exposed to dilute aqueous hydrazine at room temperature, which results in marked improvement in electrocatalytic performance. The nanowires exhibit ∼100 mV improvement in overpotential following exposure to dilute hydrazine, while also showing a 10-fold increase in current density and a significant change in Tafel slope. In situ electrical, gate-dependent measurements and spectroscopic investigations reveal that hydrazine acts as an electron dopant in molybdenum disulfide, increasing its conductivity, while also reducing the MoOx core in the core-shell nanowires, which leads to improved electrocatalytic performance.

Long life monopropellant hydrazine thruster evaluation for Space Station Freedom application - Test results

NASA Technical Reports Server (NTRS)

Popp, Christopher G.; Cook, Joseph C.; Ragland, Brenda L.; Pate, Leah R.

1992-01-01

In support of propulsion system thruster development activity for Space Station Freedom (SSF), NASA Johnson Space Center (JSC) conducted a hydrazine thruster technology demonstration program. The goal of this program was to identify impulse life capability of state-of-the-art long life hydrazine thrusters nominally rated for 50 pounds thrust at 300 psia supply pressure. The SSF propulsion system requirement for impulse life of this thruster class is 1.5 million pounds-seconds, corresponding to a throughput of approximately 6400 pounds of propellant. Long life thrusters were procured from The Marquardt Company, Hamilton Standard, and Rocket Research Company, Testing at JSC was completed on the thruster designs to quantify life while simulating expected thruster firing duty cycles and durations for SSF. This paper presents a review of the SSF propulsion system hydrazine thruster requirements, summaries of the three long life thruster designs procured by JSC and acceptance test results for each thruster, the JSC thruster life evaluation test program, and the results of the JSC test program.

Efficient hydrogen evolution in transition metal dichalcogenides via a simple one-step hydrazine reaction

DOE PAGES

Cummins, Dustin R.; Martinez, Ulises; Sherehiy, Andriy; ...

2016-06-10

In this study, hydrogen evolution reaction is catalyzed efficiently with precious metals, such as platinum; however, transition metal dichalcogenides have recently emerged as a promising class of materials for electrocatalysis, but these materials still have low activity and durability when compared with precious metals. Here we report a simple one-step scalable approach, where MoO x/MoS 2 core-shell nanowires and molybdenum disulfide sheets are exposed to dilute aqueous hydrazine at room temperature, which results in marked improvement in electrocatalytic performance. The nanowires exhibit ~100 mV improvement in over potential following exposure to dilute hydrazine, while also showing a 10-fold increase inmore » current density and a significant change in Tafel slope. In situ electrical, gate-dependent measurements and spectroscopic investigations reveal that hydrazine acts as an electron dopant in molybdenum disulfide, increasing its conductivity, while also reducing the MoO x core in the core-shell nanowires, which leads to improved electrocatalytic performance.« less

Isolation of N-linked glycopeptides by hydrazine-functionalized magnetic particles.

PubMed

Sun, Shisheng; Yang, Ganglong; Wang, Ting; Wang, Qinzhe; Chen, Chao; Li, Zheng

2010-04-01

We introduce a novel combination of magnetic particles with hydrazine chemistry, dubbed as hydrazine-functionalized magnetic particles (HFMP) for isolation of glycopeptides. Four methods have been developed and compared for the production of HFMP by hydrazine modification of the surface of the carboxyl and epoxy-silanized magnetic particles, respectively. The evaluation of the capability and specificity of HFMP as well as the optimization of the coupling condition for capturing of glycoproteins were systematically investigated. The results showed that HFMP prepared by adipic dihydrazide functionalization from carboxyl-silanized magnetic particles (HFCA) displayed the maximum capture capacity and isolated efficiency for glycoprotein. When measured with glycoproteins, the capacity of the HFCA (1 g) for coupling bovine fetuin was 130 +/- 5.3 mg. The capability of this method was also confirmed by successful isolation of all formerly glycosylated peptides from standard glycoproteins and identification of their glycosylation sites, which demonstrated the feasibility of the HFCA as an alternative solid support for isolation of glycoproteins/glycopeptides.

Colorimetric and fluorescent detection of hydrazine with high sensitivity and excellent selectivity

NASA Astrophysics Data System (ADS)

Shi, Bingjie; Qi, Sujie; Yu, Mingming; Liu, Chunxia; Li, Zhanxian; Wei, Liuhe; Ni, Zhonghai

2018-01-01

It is critical to develop probes for rapid, selective, and sensitive detection of the highly toxic hydrazine in both environmental and biological science. In this work, under mild condition, a novel colorimetric and off-on fluorescent probe was synthesized for rapid recognition of hydrazine with excellent selectivity over other various species including some biological species, metal ions and anions. The limit of quantification (LOQ) value was 1.5 × 10- 4 M-3.2 × 10- 3 M (colorimetric method) and 1.5 × 10- 4 M - 3.2 × 10- 3 M (fluorescent method) with as low as detection limit of 46.2 μM.

Monte Carlo sensitivity analysis of unknown parameters in hazardous materials transportation risk assessment.

PubMed

Pet-Armacost, J J; Sepulveda, J; Sakude, M

1999-12-01

The US Department of Transportation was interested in the risks associated with transporting Hydrazine in tanks with and without relief devices. Hydrazine is both highly toxic and flammable, as well as corrosive. Consequently, there was a conflict as to whether a relief device should be used or not. Data were not available on the impact of relief devices on release probabilities or the impact of Hydrazine on the likelihood of fires and explosions. In this paper, a Monte Carlo sensitivity analysis of the unknown parameters was used to assess the risks associated with highway transport of Hydrazine. To help determine whether or not relief devices should be used, fault trees and event trees were used to model the sequences of events that could lead to adverse consequences during transport of Hydrazine. The event probabilities in the event trees were derived as functions of the parameters whose effects were not known. The impacts of these parameters on the risk of toxic exposures, fires, and explosions were analyzed through a Monte Carlo sensitivity analysis and analyzed statistically through an analysis of variance. The analysis allowed the determination of which of the unknown parameters had a significant impact on the risks. It also provided the necessary support to a critical transportation decision even though the values of several key parameters were not known.

SECONDARY COMBUSTION OF PENTABORANE-HYDRAZINE EXHAUST IN AIR

DTIC Science & Technology

The design of the first of two liquid micromotors , has been completed. This micromotor will be used for the determination of characteristic velocity... micromotor and auxiliary equipment has been initiated. A tentative test plan has been developed for the study of the combustion characteristics in air of the pentaborane-hydrazine system.

A Hydrazine-Free Wolff-Kishner Reaction Suitable for an Undergraduate Laboratory

ERIC Educational Resources Information Center

Cranwell, Philippa B.; Russell, Andrew T.

2016-01-01

A Wolff-Kishner reaction that does not require hydrazine has been developed. The reaction sequence has two steps: formation of a carbomethoxyhydrazone from methyl hydrazinocarboxylate and acetophenone, then decomposition of this intermediate by treatment with potassium hydroxide in triethylene glycol. Purification is by filtration through a plug…

SOLVENT-FREE REDUCTION OF AROMATIC NITRO COMPOUNDS WITH ALUMINA-SUPPORTED HYDRAZINE UNDER MICROWAVE IRRADIATION

EPA Science Inventory

In a solvent-free microwave-expedited process, aromatic nitro compounds are readily reduced to the corresponding amino compounds in good yield with hydrazine hydrate supported on alumina in presence of FeCl3, 6H2), Fe(III) oxide hydroxide or Fe(III) oxides.

Toxicity Warning Badge

NASA Technical Reports Server (NTRS)

1996-01-01

Kennedy Space Center contracted GMD Systems, Inc., now Bacharach, Inc., to design a system for monitoring personnel exposure to hydrazine and monomethyl hydrazine, two dangerous gases which ignite on contact with an oxidizer. GMD developed a reliable colorimetric gas monitoring dosimeter for NASA, then modified it to create the commercial GMD 530 Series Hydrazine Badge. The badge has two separate paper tape chemistries which change color when the gases are detected, the density of the color being in proportion to the time of exposure and amount of gas in the air. The badge is used in facilities where hypergolic fuel is produced or used in support of space vehicles, satellites, missiles, and military aircraft auxiliary power units.

Solvent properties of hydrazine in the preparation of metal chalcogenide bulk materials and films.

PubMed

Yuan, Min; Mitzi, David B

2009-08-21

A combination of unique solvent properties of hydrazine enables the direct dissolution of a range of metal chalcogenides at ambient temperature, rendering this an extraordinarily simple and soft synthetic approach to prepare new metal chalcogenide-based materials. The extended metal chalcogenide parent framework is broken up during this process, and the resulting metal chalcogenide building units are re-organized into network structures (from 0D to 3D) based upon their interactions with the hydrazine/hydrazinium moieties. This Perspective will review recent crystal and materials chemistry developments within this family of compounds and will briefly discuss the utility of this approach in metal chalcogenide thin-film deposition.

Propagation of detonations in hydrazine vapor

NASA Technical Reports Server (NTRS)

Heinrich, H. J.

1985-01-01

In the range of greater hydrazine vapor pressure, detonation speed depends exclusively on the extent of the ammonia decomposition in the second reaction stage. As vapor pressure decreases, the ammonia disintegration speed becomes increasingly slower and the reaction reached in the reaction zone increasingly decreases until finally, in the vapor pressure range between 53 and 16 Torr, the contribution of the second stage to detonation propagation disappears, and only the first stage remains active. Since the disintegration speed of the hydrazine in this pressure range has decreased markedly as well, no level, but rather only spinning, detonations occur. Temporary separations of the impact front and the reaction zone in the process lead to fluctuations of the detonation speed.

Selective fluorescent detection of aspartic acid and glutamic acid employing dansyl hydrazine dextran conjugate.

PubMed

Nasomphan, Weerachai; Tangboriboonrat, Pramuan; Tanapongpipat, Sutipa; Smanmoo, Srung

2014-01-01

Highly water soluble polymer (DD) was prepared and evaluated for its fluorescence response towards various amino acids. The polymer consists of dansyl hydrazine unit conjugated into dextran template. The conjugation enhances higher water solubility of dansyl hydrazine moiety. Of screened amino acids, DD exhibited selective fluorescence quenching in the presence of aspartic acid (Asp) and glutamic acid (Glu). A plot of fluorescence intensity change of DD against the concentration of corresponding amino acids gave a good linear relationship in the range of 1 × 10(-4) M to 25 × 10(-3) M. This establishes DD as a potential polymeric sensor for selective sensing of Asp and Glu.

Liquid-Phase Heat-Release Rates of the Systems Hydrazine-Nitric Acid and Unsymmetrical Dimethylhydrazine-Nitric Acid

NASA Technical Reports Server (NTRS)

Somogyi, Dezso; Feiler, Charles E.

1960-01-01

The initial rates of heat release produced by the reactions of hydrazine and unsymmetrical dimethylhydrazine with nitric acid were determined in a bomb calorimeter under conditions of forced mixing. Fuel-oxidant weight ratio and injection velocity were varied. The rate of heat release apparently depended on the interfacial area between the propellants. Above a narrow range of injection velocities representing a critical amount of interfacial area, the rates reached a maximum and were almost constant with injection velocity. The maximum rate for hydrazine was about 70 percent greater than that for unsymmetrical dimethylhydrazine. The total heat released did not vary with mixture ratio over the range studied.

Nontoxic Hydroxylammonium Nitrate (HAN) Monopropellant Propulsion

NASA Technical Reports Server (NTRS)

McKechnie, Timothy N.

2015-01-01

Nontoxic monopropellants have been developed that provide better performance than toxic hydrazine. Formulations based on HAN have superior performance as compared to hydrazine with enhanced specific impulse (Isp), higher density and volumetric impulse, lower melting point, and much lower toxicity. However, HAN-based monopropellants require higher chamber temperatures (2,083 K vs. 883 K) to combust. Current hydrazine-based combustion chamber technology (Inconel® or niobium C103 and silicide coating) and catalyst (Shell 405) are inadequate. In Phase I, state-of-the-art iridium-lined rhenium chambers and innovative new foam catalysts were demonstrated in pulse and 10-second firings. Phase II developed and tested a flight-weight thruster for an environmentally green monopropellant.

PRECIPITATION OF PLUTONOUS PEROXIDE

DOEpatents

Barrick, J.G.; Manion, J.P.

1961-08-15

A precipitation process for recovering plutonium values contained in an aqueous solution is described. In the process for precipitating plutonium as plutonous peroxide, hydroxylamine or hydrazine is added to the plutoniumcontaining solution prior to the addition of peroxide to precipitate plutonium. The addition of hydroxylamine or hydrazine increases the amount of plutonium precipitated as plutonous peroxide. (AEC)

40 CFR 721.4340 - Substituted thiazino hydrazine salt (generic name).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Substituted thiazino hydrazine salt (generic name). 721.4340 Section 721.4340 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4340...

14 CFR 420.66 - Separation distance requirements for storage of hydrogen peroxide, hydrazine, and liquid hydrogen...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false Separation distance requirements for storage of hydrogen peroxide, hydrazine, and liquid hydrogen and any incompatible energetic liquids stored within an intraline distance. 420.66 Section 420.66 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION...

14 CFR 420.66 - Separation distance requirements for storage of hydrogen peroxide, hydrazine, and liquid hydrogen...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false Separation distance requirements for storage of hydrogen peroxide, hydrazine, and liquid hydrogen and any incompatible energetic liquids stored within an intraline distance. 420.66 Section 420.66 Aeronautics and Space COMMERCIAL SPACE TRANSPORTATION...

Overview of reductants utilized in nuclear fuel reprocessing/recycling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paviet-Hartmann, P.; Riddle, C.; Campbell, K.

2013-07-01

The most widely used reductant to partition plutonium from uranium in the Purex process was ferrous sulfamate, other alternates were proposed such as hydrazine-stabilized ferrous nitrate or uranous nitrate, platinum catalyzed hydrogen, and hydrazine, hydroxylamine salts. New candidates to replace hydrazine or hydroxylamine nitrate (HAN) are pursued worldwide. They may improve the performance of the industrial Purex process towards different operations such as de-extraction of plutonium and reduction of the amount of hydrazine which will limit the formation of hydrazoic acid. When looking at future recycling technologies using hydroxamic ligands, neither acetohydroxamic acid (AHA) nor formohydroxamic acid (FHA) seem promisingmore » because they hydrolyze to give hydroxylamine and the parent carboxylic acid. Hydroxyethylhydrazine, HOC{sub 2}H{sub 4}N{sub 2}H{sub 3} (HEH) is a promising non-salt-forming reductant of Np and Pu ions because it is selective to neptunium and plutonium ions at room temperature and at relatively low acidity, it could serve as a replacement of HAN or AHA for the development of a novel used nuclear fuel recycling process.« less

Comparative studies on single-layer reduced graphene oxide films obtained by electrochemical reduction and hydrazine vapor reduction

NASA Astrophysics Data System (ADS)

Wang, Zhijuan; Wu, Shixin; Zhang, Juan; Chen, Peng; Yang, Guocheng; Zhou, Xiaozhu; Zhang, Qichun; Yan, Qingyu; Zhang, Hua

2012-02-01

The comparison between two kinds of single-layer reduced graphene oxide (rGO) sheets, obtained by reduction of graphene oxide (GO) with the electrochemical method and hydrazine vapor reduction, referred to as E-rGO and C-rGO, respectively, is systematically studied. Although there is no morphology difference between the E-rGO and C-rGO films adsorbed on solid substrates observed by AFM, the reduction process to obtain the E-rGO and C-rGO films is quite different. In the hydrazine vapor reduction, the nitrogen element is incorporated into the obtained C-rGO film, while no additional element is introduced to the E-rGO film during the electrochemical reduction. Moreover, Raman spectra show that the electrochemical method is more effective than the hydrazine vapor reduction method to reduce the GO films. In addition, E-rGO shows better electrocatalysis towards dopamine than does C-rGO. This study is helpful for researchers to understand these two different reduction methods and choose a suitable one to reduce GO based on their experimental requirements.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chumakov, Yu. M.; Paholnitcaia, A. Yu.; Petrenko, P. A.

Two crystal modifications of nitrato-(2-[2-(1-pyridine-2-ylethylidene)hydrazine]-1,3-benzothiazolo) aquacopper (I and II) and two modifications of chloro-(2-[2-phenyl(pyridine-2-ylethylidene)hydrazine]-1,3-benzothiazolo) copper (III and IV) have been synthesized and studied by X-ray diffraction. In structures I and II, the copper atoms coordinate a monodeprotonated molecule of the organic ligand, nitrate ions, and a water molecule. In crystals of I, the complexes are monomeric, whereas complexes II are linked via nitrate ions to form polymeric chains. In both structures the coordination polyhedron of the copper atom can be described as a distorted tetragonal bipyramid—(4 + 1 + 1) in I and (4 + 2) in II. These coordinationmore » polyherdra have different compositions. In structures III and IV, the metal atoms coordinate a monodeprotonated (2-[2-phenyl(pyridine-2-ylethylidene)hydrazine]-1,3-benzothiazole molecule and chloride ions. In III the complex-forming ion has square-planar coordination geometry, whereas structure IV consists of centrosymmetric dimers with two bridging chlorine atoms. It was found that nitrato-(2-[2-(1-pyridine-2-ylethylidene)hydrazine]-1,3-benzothiazolo) aquacopper possesses antitumor activity.« less

Reduced Toxicity, High Performance Monopropellant at the U.S. Air Force Research Laboratory

NASA Astrophysics Data System (ADS)

Hawkins, T. W.; Brand, A. J.; McKay, M. B.; Tinnirello, M.

2010-09-01

Current programs are aiming to develop reduced toxicity monopropellant formulations to replace spacecraft hydrazine monopropellant. The Air Force Research Laboratory's(AFRL's) approach to replacing hydrazine is the synthesis and development of energetic compounds/formulations with substantially less vapor toxicity and superior performance(specific impulse and density). Characterization and testing of these high energy density materials is an essential part of the screening process for viable advanced propellants. Hazardous handling characteristics, undesirable physical properties or unacceptable sensitivity behaviors must also be identified and/or modified to further development by a potential user. AFRL has successfully identified a novel monopropellant(designated AF-M315E) that shows great promise as an avenue toward replacement of hydrazine monopropellant for spacecraft propulsion. Hazard and safety/sensitivity, stability, and toxicity studies have been conducted on the monopropellant and will be described. The results from AF-M315E indicate that a >50% improvement in propulsion system performance over hydrazine is achievable while simultaneously providing a safer environment for the general public, ground personnel, crews and flight participants.

N-2-Hydroxy-4-methoxyacetophenone- N'-4-nitrobenzoyl hydrazine: Synthesis and structural characterization

NASA Astrophysics Data System (ADS)

Bessy Raj, B. N.; Kurup, M. R. Prathapachandra

2007-04-01

A new aroyl hydrazone, N-2-hydroxy-4-methoxyacetophenone- N'-4-nitrobenzoyl hydrazine was prepared by the condensation reaction of 2-hydroxy-4-methoxyacetophenone and 4-nitrobenzoyl hydrazine. Characterization of the compound was done by elemental analysis and electronic, infrared and NMR spectral analyses. The complete structural assignment of the compound was done by NMR studies by using COSY homonuclear and HSQC heteronuclear techniques. The crystal and molecular structure was determined by single crystal X-ray diffraction studies: crystallized in the monoclinic system, space group P2 1/ n, Z = 4, a = 7.3343(9) Å, b = 20.3517(9) Å, c = 10.1375(5) Å, α = 90.00°, β = 95.735(7)° and γ = 90.00°. From the crystal structure, it is concluded that the compound exists as the keto isomer in the solid state. There is a completely extended conformation in the central part of the molecule C5 sbnd C8 dbnd N1 sbnd N2 sbnd C10 dbnd O2 with an E configuration at the double bond of the hydrazinic bridge.

Suicide inactivation of hydroxylamine oxidoreductase of Nitrosomonas europaea by organohydrazines.

PubMed

Logan, M S; Hooper, A B

1995-07-18

In the presence of a suitable electron acceptor such as mammalian cytochrome c, hydroxylamine oxidoreductase (HAO) from the chemolithotrophic bacterium Nitrosomonas europaea catalyzes the oxidation of hydroxylamine or hydrazine to nitrite or dinitrogen, respectively. Each subunit of HAO contains 7 c-hemes and a chromophore of the active site called heme P460, a c-heme bridged from a methylene carbon to a ring carbon of a tyrosine of the peptide chain. Reaction with either substrate results in reduction of several c-hemes of HAO. The reaction of organohydrazines with HAO was investigated in this work. HAO was inactivated by (phenyl-, (methyl-, or (hydroxyethyl)hydrazine. The process followed first order kinetics and was inhibited by the substrates, hydroxylamine or hydrazine. Complete loss of enzyme activity and absorbancy characteristic of native heme P460 of HAO occurred at a 1:1 ratio of phenylhydrazine and HAO. HAO was covalently derivatized by two molecules of [14C]-phenylhydrazine per subunit. Heme P460 was derivatized with high affinity, and an amino acid residue was derivatized with lower affinity. c-Hemes were not derivatized except for the partial reaction of (hydroxyethyl)hydrazine with one heme. As with hydroxylamine and hydrazine, incubation with organohydrazines resulted in reduction of c-heme of HAO. Derivatized minus native optical difference spectra of ferric or ferrous HAO revealed changes in the optical properties of heme P460 which were generally similar to shifts seen in the reaction of the heme of other hemoproteins with organohydrazines.(ABSTRACT TRUNCATED AT 250 WORDS)

Palladium nanoparticles decorated on reduced graphene oxide rotating disk electrodes toward ultrasensitive hydrazine detection: effects of particle size and hydrodynamic diffusion.

PubMed

Krittayavathananon, Atiweena; Srimuk, Pattarachai; Luanwuthi, Santamon; Sawangphruk, Montree

2014-12-16

Although metal nanoparticle/graphene composites have been widely used as the electrode in electrochemical sensors, two effects, consisting of the particle size of the nanoparticles and the hydrodynamic diffusion of analytes to the electrodes, are not yet fully understood. In this work, palladium nanoparticles/reduced graphene oxide (PdNPs/rGO) composites were synthesized using an in situ polyol method. Palladium(II) ions and graphene oxide were reduced together with a reducing agent, ethylene glycol. By varying the concentration of palladium(II) nitrate, PdNPs with different sizes were decorated on the surface of rGO sheets. The as-fabricated PdNPs/rGO rotating disk electrodes (RDEs) were investigated toward hydrazine detection. Overall, a 3.7 ± 1.4 nm diameter PdNPs/rGO RDE exhibits high performance with a rather low limit of detection of about 7 nM at a rotation speed of 6000 rpm and provides a wide linear range of 0.1-1000 μM with R(2) = 0.995 at 2000 rpm. This electrode is highly selective to hydrazine without interference from uric acid, glucose, ammonia, caffeine, methylamine, ethylenediamine, hydroxylamine, n-butylamine, adenosine, cytosine, guanine, thymine, and l-arginine. The PdNPs/rGO RDEs with larger sizes show lower detection performance. Interestingly, the detection performance of the electrodes is sensitive to the hydrodynamic diffusion of hydrazine. The as-fabricated electrode can detect trace hydrazine in wastewater with high stability, demonstrating its practical use as an electrochemical sensor. These findings may lead to an awareness of the effect of the hydrodynamic diffusion of analyte that has been previously ignored, and the 3.7 ± 1.4 nm PdNPs/rGO RDE may be useful toward trace hydrazine detection, especially in wastewater from related chemical industries.

Intramolecular Electron Transfer in Bis(tetraalkyl Hydrazine) and Bis(hydrazyl) Radical Cations.

NASA Astrophysics Data System (ADS)

Chang, Hao

A series of multicyclic bis(hydrazine) and bis(diazenium) compounds connected by relatively rigid hydrocarbon frameworks were prepared for the study of intramolecular electron transfer. The thermodynamics of electron removal of these compounds was investigated by cyclic voltammetry. The difference between the first and second oxidation potentials for the 4 sigma-bonded species was found to be larger for the bis(hydrazyl) radical systems than for the bis(hydrazines) by ca. 0.2 V (4.6 kcal/mol). This indicates a greater degree of interaction between the two nitrogen moieties for the hydrazyl systems, which is consistent with a greater degree of electronic coupling (H _{rm AB}) in these systems. The ESR spectra of the 4 sigma -bonded bis(hydrazine) radical cations indicate localized radical cations, which corresponds to slow intramolecular electron transfer on the ESR timescale. Conversely, the ESR spectra of the corresponding bis(hydrazyl) radical cation systems show nitrogen hyperfine splittings of a(4N) of ca. 4.5 G. This indicates that intramolecular electron transfer between the two nitrogen moieties is fast on the ESR timescale; the rate of exchange, k_ {rm ex} was estimated to be well above 1.9 times 10^8 s^{-1}. The contrast in exchange rates is consistent with the large geometry change upon oxidation which is characteristic of hydrazines. The hydrazyls undergo a smaller geometry change upon oxidation, and thus are expected to exhibit smaller inner-sphere reorganization energies. The optical spectra of these radical species was investigated in hopes of observing absorption bands corresponding to intramolecular electron transfer, as predicted by Hush theory. A broad absorption band was observed in the near IR region for the saturated bis(hydrazyl) radical cation system at 1060 nm (9420 cm^{-1} ) in acetonitrile at room temperature, and was accompanied by a narrower band at 1430 nm (6993 cm^ {-1}). The width of this band was estimated to be 545 nm (6496 cm^{-1}). A much higher energy band was observed in the UV/Vis region, at 520 nm (19,230 cm^{-1}) in acetonitrile for the corresponding bis(hydrazine) radical cation. The width of this band was estimated to be 240 nm (7211 cm^{-1}). The difference in the energies of these absorbance bands, E _{rm op}, reflects the different inner-sphere reorganization energies of the hydrazyl and hydrazine systems. Using Hush analysis, the electron coupling, H_{rm AB} , was calculated to be ca. 3.5 kcal/mol for the bis(hydrazyl) radical cation systems; a smaller value of H_{rm AB} of 1 kcal/mol was obtained for the bis(hydrazine) radical cations. This difference in electronic coupling is consistent with the faster rate of electron transfer, as well as the smaller inner-sphere reorganization energy in the bis(hydrazyl) systems.

The Second Conference on the Environmental Chemistry of Hydrazine Fuels; 15 February 1979.

DTIC Science & Technology

1982-04-01

tank by a moving piston in the tank. The hydrazine trave’s to a gas generator where it decomposes on an iridium /alumina catalyst. The gas is used to...possibility of nitrogen trichloride formation and presented control instrument problems since commercially available instru- ments required p11 of about 5

Reactivity of pyrylium salts toward basic reactants

NASA Technical Reports Server (NTRS)

Neidlein, R.; Witerzens, P.

1981-01-01

The reactivity of some N-acyl and N-sulfonyl-hydrazines 2-4, 10a-10g, 12, 13, 16a, 16b and of hydrazones 18, benzyldihydrazone 21 towards pyrylium salts 1 was examined. By reaction of 2,4,6-trimethyl-pyrylium salt 1 with substituted hydrazines some pyridinium salts were obtained. Relationships between basicity and reactivity were discussed.

A facile thermal decomposition route to synthesise CoFe2O4 nanostructures

NASA Astrophysics Data System (ADS)

Kalpanadevi, K.; Sinduja, C. R.; Manimekalai, R.

2014-01-01

The synthesis of CoFe2O4 nanoparticles has been achieved by a simple thermal decomposition method from an inorganic precursor, cobalt ferrous cinnamate hydrazinate (CoFe2(cin)3(N2H4)3) which was obtained by a novel precipitation method from the corresponding metal salts, cinnamic acid and hydrazine hydrate. The precursor was characterized by hydrazine and metal analyses, infrared spectral analysis and thermo gravimetric analysis. Under appropriate annealing, CoFe2(cin)3(N2H4)3 yielded CoFe2O4 nanoparticles, which were characterized for their size and structure using X-Ray diffraction (XRD), high resolution transmission electron microscopic (HRTEM), selected area electron diffraction (SAED) and scanning electron microscopic (SEM) techniques.

Recent Developments in Chemically Reactive Sensors for Propellants

NASA Technical Reports Server (NTRS)

Davis, Dennis D.; Mast, Dion J.; Baker, David L.; Fries, Joseph (Technical Monitor)

1999-01-01

Propellant system leaks can pose a significant hazard in aerospace operations. For example, a leak in the hydrazine supply system of the shuttle auxiliary power unit (APU) has resulted in hydrazine ignition and fire in the aft compartment of the shuttle. Sensors indicating the location of a leak could provide valuable information required for operational decisions. WSTF has developed a small, single-use sensor for detection of propellant leaks. The sensor is composed of a thermistor bead coated with a substance which is chemically reactive with the propellant. The reactive thermistor is one of a pair of closely located thermistors, the other being a reference. On exposure to the propellant, the reactive coating responds exothermically to it and increases the temperature of the coated-thermistor by several degrees. The temperature rise is sensed by a resistive bridge circuit, and an alarm is registered by data acquisition software. The concept is general and has been applied to sensors for hydrazine, monomethylhydrazine, unsym-dimethylhydrazine, ammonia, hydrogen peroxide, ethanol, and dinitrogen tetroxide. Responses of these sensors to humidity, propellant concentration, distance from the liquid leak, and ambient pressure levels arc presented. A multi-use sensor has also been developed for hydrazine based on its catalytic reactivity with noble metals.

Derivatization Ion Chromatography for the Determination of Monoethanolamine in Presence of Hydrazine in PHWR Steam-Water Circuits

PubMed Central

D., Ayushi; Sengupta, Arijit; Kumar, Sangita D.; Kumbhar, A. G.; Venkateswaran, G.

2011-01-01

A simple, rapid and accurate method for the determination of monoethanolamine (MEA) in PHWR steam-water circuits has been developed. MEA is added in the feed water to provide protection against corrosion while hydrazine is added to scavenge dissolved oxygen. The quantitative determination of MEA in presence of hydrazine was accomplished using derivatization ion chromatography with conductometric detection in nonsuppressed mode. A Metrosep cation 1-2 analytical column and a Metrosep cartridge were used for cation separation. A mixture of 4 mM tartaric acid, 20% acetone and 0.05 mM HNO3 was used as eluent. Acetone in the mobile phase leads to the formation of different derivatives with MEA and hydrazine. The interferences due Na+ and NH4  + were eliminated by adopting a simple pretreatment procedure employing OnGuard-H cartridge. The limit of detection limit of MEA was 0.1 μg mL−1 and the relative standard deviation was 2% for the overall method. The recovery of MEA added was in the range 95%–102%. The method was applied to the determination of MEA in steam generator water samples. PMID:21785596

An Improved Calibration Method for Hydrazine Monitors for the United States Air Force

DOE Office of Scientific and Technical Information (OSTI.GOV)

Korsah, K

2003-07-07

This report documents the results of Phase 1 of the ''Air Force Hydrazine Detector Characterization and Calibration Project''. A method for calibrating model MDA 7100 hydrazine detectors in the United States Air Force (AF) inventory has been developed. The calibration system consists of a Kintek 491 reference gas generation system, a humidifier/mixer system which combines the dry reference hydrazine gas with humidified diluent or carrier gas to generate the required humidified reference for calibrations, and a gas sampling interface. The Kintek reference gas generation system itself is periodically calibrated using an ORNL-constructed coulometric titration system to verify the hydrazine concentrationmore » of the sample atmosphere in the interface module. The Kintek reference gas is then used to calibrate the hydrazine monitors. Thus, coulometric titration is only used to periodically assess the performance of the Kintek reference gas generation system, and is not required for hydrazine monitor calibrations. One advantage of using coulometric titration for verifying the concentration of the reference gas is that it is a primary standard (if used for simple solutions), thereby guaranteeing, in principle, that measurements will be traceable to SI units (i.e., to the mole). The effect of humidity of the reference gas was characterized by using the results of concentrations determined by coulometric titration to develop a humidity correction graph for the Kintek 491 reference gas generation system. Using this calibration method, calibration uncertainty has been reduced by 50% compared to the current method used to calibrate hydrazine monitors in the Air Force inventory and calibration time has also been reduced by more than 20%. Significant findings from studies documented in this report are the following: (1) The Kintek 491 reference gas generation system (generator, humidifier and interface module) can be used to calibrate hydrazine detectors. (2) The Kintek system output concentration is less than the calculated output of the generator alone but can be calibrated as a system by using coulometric titration of gas samples collected with impingers. (3) The calibrated Kintek system output concentration is reproducible even after having been disassembled and moved and reassembled. (4) The uncertainty of the reference gas concentration generated by the Kintek system is less than half the uncertainty of the Zellweger Analytics' (ZA) reference gas concentration and can be easily lowered to one third or less of the ZA method by using lower-uncertainty flow rate or total flow measuring instruments. (5) The largest sources of uncertainty in the current ORNL calibration system are the permeation rate of the permeation tubes and the flow rate of the impinger sampling pump used to collect gas samples for calibrating the Kintek system. Upgrading the measurement equipment, as stated in (4), can reduce both of these. (6) The coulometric titration technique can be used to periodically assess the performance of the Kintek system and determine a suitable recalibration interval. (7) The Kintek system has been used to calibrate two MDA 7100s and an Interscan 4187 in less than one workday. The system can be upgraded (e.g., by automating it) to provide more calibrations per day. (8) The humidity of both the reference gas and the environment of the Chemcassette affect the MDA 7100 hydrazine detector's readings. However, ORNL believes that the environmental effect is less significant than the effect of the reference gas humidity. (9) The ORNL calibration method based on the Kintek 491 M-B gas standard can correct for the effect of the humidity of the reference gas to produce the same calibration as that of ZA's. Zellweger Analytics calibrations are typically performed at 45%-55% relative humidity. (10) Tests using the Interscan 4187 showed that the instrument was not accurate in its lower (0-100 ppb) range. Subsequent discussions with Kennedy Space Center (KSC) personnel also indicated that the Interscan units were not reproducible when new sensors were used. KSC had discovered that the Interscan units read incorrectly on the low range because of the presence of carbon dioxide. ORNL did not test the carbon dioxide effect, but it was found that the units did not read zero when a test gas containing no hydrazine was sampled. According to the KSC personnel that ORNL had these discussions with, NASA is phasing out the use of these Interscan detectors.« less

The PI3K/Akt pathway in colitis associated colon cancer and its chemoprevention with celecoxib, a Cox-2 selective inhibitor.

PubMed

Setia, Shruti; Nehru, Bimla; Sanyal, Sankar Nath

2014-07-01

Oncogenesis and angiogenesis are the two major pathways involved in tumorigenesis. Oncogenesis involves the PI3K/Akt and Wnt/β-catenin pathways, both of which are upregulated in several types of cancers. We established animal model of ulcerative colitis, colon cancer and colitis associated colon cancer by the incorporation of dextran sufate sodium (DSS) and dimethyl hydrazine (DMH), alone as well as in combination. Apart from the gross morphological analysis, we presently explored the role of various components of the oncogenic pathways, including PI3K, p-Akt, PTEN, PDK1, mTOR, GSK-3β, Wnt and β-catenin and found the elevated levels of these proteins, except the tumor suppressors PTEN and GSK-3β, whose levels were downregulated in both inflammatory and carcinogenic conditions. We also studied the protein expression of some major angiogenic agents, such as Vegf, MMP-2, MMP-9 and iNOS. The angiogenic pathway was also upregulated presently in the DSS, DMH and DSS+DMH groups. Also, the reactive oxygen and nitrogen species, which lead to oxidative stress, were found to be elevated in these groups. All these effects were brought towards normal by the co-administration of celecoxib, a second generation non-steroidal anti-inflammatory drug (NSAID), with DSS, DMH and their combinatorial group. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Dietary selenium protects adiponectin knockout mice against chronic inflammation induced colon cancer.

PubMed

Saxena, Arpit; Fayad, Raja; Kaur, Kamaljeet; Truman, Samantha; Greer, Julian; Carson, James A; Chanda, Anindya

2017-04-03

Selenium (Se) is an essential dietary micronutrient that has been examined for protection against different types of cancers including colon cancer. Despite an established inverse association between Se and chronic inflammation induced colon cancer (CICC), the mechanistic understanding of Se's protective effects requires additional in-vivo studies using preclinical animal models of CICC. Adiponectin (APN) is an adipocytokine that is protective against CICC as well. However, its role in the anti-mutagenic effects of the Se-diet remains unknown. To address this knowledge gap, here we examine the ability of dietary Se in reducing CICC in APN knockout mice (KO) and its wild-type C57BL/6. CICC was induced with the colon cancer agent 1,2 dimethyl hydrazine (DMH) along with dextran sodium sulfate (DSS). Se-enhanced diet increased selenoproteins, Gpx-1 and Gpx-2, in the colon tissues, thereby reducing oxidative stress. Se-mediated reduction of CICC was evident from the histopathological studies in both mouse models. In both mice, reduction in inflammation and tumorigenesis associated well with reduced p65 phosphorylation and elevated 53 phosphorylation. Finally, we show that in both models Se-administration promotes goblet cell differentiation with a concomitant increase in the levels of associated proteins, Muc-2 and Math-1. Our findings suggest that Se's protection against CICC involves both colonic epithelial protection and anti-tumor effects that are independent of APN.

A novel 4-phenyl amino thiourea derivative designed for real-time ratiometric-colorimetric detection of toxic Pb2.

PubMed

Guang, Yi S; Ren, Xia; Zhao, Shuang; Yan, Quan Z; Zhao, Gang; Xu, Yao H

2018-05-12

The objective of this study was to develop a ratiometric and colorimetric organic sensor for Pb 2+ detection in environmental samples. A new probe 4-phenyl amino thiourea (PAT) was designed and synthesized using hydrazine hydrate and phenyl isothiocyanate as raw materials. After its structure was characterized and confirmed, its UV-vis spectral property was investigated in detail. PAT possesses a specifically real-time, ratiometric and colorimetric response to Pb 2+ in dimethyl formamide (DMF)/H 2 O (v/v = 9:1, pH = 7.0) within 18.0 s. There was little interference in the presence of some other common metal ions, such as Fe 3+ , Cd 2+ , Zn 2+ , Mg 2+ , Cr 3+ , Ca 2+ , Ba 2+ , Sn 2+ , Na + , Mn 2+ , Hg 2+ , and Pb 2+ . Under the optimized conditions (DMF/H 2 O with v/v of 9:1, c PAT = 1.0 × 10 -3 mol·L -1 , pH = 7.0), the present sensor PAT was successfully applied for Pb 2+ determination in environmental water samples with satisfied recoveries (83.0%-106.0%) and analytical precision (≤7.2%). The recognition mechanism was confirmed to form a stable 1:1 six-member ring complex between the target dye and Pb 2+ with a coordination constant of 4.96 × 10 4 .

Synthesis, Characterization, and Biological Evaluation of certain 6-methyl-2(3H)-benzo-1, 3-thiazolyl-1'-ethylidene-2-(o, p- Substituted Acetophenones) Hydrazine Analogs.

PubMed

Alang, G; Kaur, G; Kaur, R; Singh, A; Tiwari, R

2010-10-01

In the present study, five new derivatives (GG4 to GG8) of benzothiazoles were synthesized and evaluated against Staphylococcus aureus (MTCC 737), Pseudomonas aeruginosa (MTCC 424), Escherichia coli (MTCC 1687), and yeast-like fungi Candida tropicalis. p-Toluidine on treatment with ammonium thiocynate formed 2-benzothiazolamines (II), which on reaction with hydrazine hydrate formed a hydrazino derivative (III). Compounds GG4 to GG8 were synthesized by reacting the hydrazine derivative with different acetophenones. All the synthesized compounds were identified by IR and (1)H-NMR, and antimicrobial activity was performed on the synthesized compounds. Presence of NO(2), Br, OCH(3), and Cl groups to the substituted benzothiazole enhanced the antibacterial and antifungal activities.

IMPROVEMENT UPON THE CARRIER PRECIPITATION OF PLUTONIUM IONS FROM NITRIC ACID SOLUTIONS

DOEpatents

James, R.A.; Thompson, S.G.

1958-12-23

A process is reported for improving the removal of plutonlum by carrier precipitation by the addition of nitrite ions to a nitrlc acid solutlon of neutronirradiated unanium so as to destroy any hydrazine that may be present in the solution since the hydrazine tends to complex the tetravalent plutonium and prevents removal by the carrier precipltate, such as bismuth phospbate.

A novel electrochemical sensor based on Cu3P@NH2-MIL-125(Ti) nanocomposite for efficient electrocatalytic oxidation and sensitive detection of hydrazine

NASA Astrophysics Data System (ADS)

Wang, Minghua; Yang, Longyu; Hu, Bin; Liu, Yongkang; Song, Yingpan; He, Linghao; Zhang, Zhihong; Fang, Shaoming

2018-07-01

A novel electrocatalyst based on amine-functionalized Ti-based metal-organic framework (NH2-MIL-125(Ti)) embedded with Cu3P nanocrystals (denoted by Cu3P@NH2-MIL-125(Ti)) was synthesized and used for electrocatalytic oxidation and detection of hydrazine in aqueous solution. A series of Cu3P@NH2-MIL-125(Ti) nanocomposites were obtained by adding Cu3P nanoparticles into the preparation system of NH2-MIL-125(Ti), with the Cu3P nanocrystals derived from the phospatization of Cu(OH)2 at high temperature. Based on the detailed characterizations and analysis of the chemical and physical performances of the series of Cu3P@NH2-MIL-125(Ti) nanocomposites at dosages of Cu3P nanocrystals at 5, 20, 50, and 100 mg, the good synergic effect between the Cu3P (50 mg) and the NH2-MIL-125(Ti) endows the as-prepared Cu3P50@NH2-MIL-125(Ti) nanocomposite with the excellent electrocatalytic activity toward the electrocatalytic oxidation of hydrazine. The Cu3P50@NH2-MIL-125(Ti)-based electrochemical sensor exhibited a detection limit of 79 nM (S/N = 3) within a wider linear range from 5 μM to 7.5 mM. Moreover, the developed sensor exhibited high selectivity toward the detection of hydrazine with the addition of certain common interferents and good applicability in real samples. All of these results imply that the Cu3P50@NH2-MIL-125(Ti) nanocomposite could be promising for detecting hydrazine and offer potential applications in the field of electroanalytical chemistry.

2-(Hetero(aryl)methylene)hydrazine-1-carbothioamides as potent urease inhibitors.

PubMed

Saeed, Aamer; Imran, Aqeel; Channar, Pervaiz A; Shahid, Mohammad; Mahmood, Wajahat; Iqbal, Jamshed

2015-02-01

A small series of 2-(hetero(aryl)methylene) hydrazine-1-carbothioamides including two aryl derivatives was synthesized and tested for their inhibitory activity against urease. Compound (E)-2-(Furan-2-ylmethylene) hydrazine-1-carbothioamide (3f), having a furan ring, was the most potent inhibitor of urease with an IC50 value of 0.58 μM. Molecular modeling was carried out through docking the designed compounds into the urease binding site to predict whether these derivatives have analogous binding mode to the urease inhibitors. The study revealed that all of the tested compounds bind with both metal atoms at the active site of the enzyme. The aromatic ring of the compounds forms ionic interactions with the residues, Ala(440), Asp(494), Ala(636), and Met(637). © 2014 John Wiley & Sons A/S.

Photoconversion of 4-nitrophenol in the presence of hydrazine with AgNPs-TiO2 nanoparticles prepared by the sol-gel method.

PubMed

Hernández-Gordillo, Agileo; Arroyo, Missael; Zanella, R; Rodríguez-González, V

2014-03-15

The photocatalytic properties of functionalized TiO2 with silver nanoparticles (AgNPs) for the conversion of 4-nitrophenol to 4-aminophenol in the presence of hydrazine were investigated. The TiO2 semiconductor synthesized by the sol-gel method was functionalized with AgNPs at different loadings, and their structural and optical properties were characterized by several techniques. The functionalized TiO2 with 1.5wt% AgNPs presented the highest photocatalytic activity for the conversion of 4-nitrophenol with appropriate hydrazine concentrations (0.5M). The photoefficiency enhancement under UV light irradiation was attributed to the electron transfer from the TiO2 semiconductor surface to the adsorbed acceptor reactant (4-nitrophenol) through the deposited AgNPs. Copyright © 2014 Elsevier B.V. All rights reserved.

Synthesis, Characterization, and Biological Evaluation of certain 6-methyl-2(3H)-benzo-1, 3-thiazolyl-1’-ethylidene-2-(o, p- Substituted Acetophenones) Hydrazine Analogs

PubMed Central

Alang, G; Kaur, G; Kaur, R; Singh, A; Tiwari, R

2010-01-01

In the present study, five new derivatives (GG4 to GG8) of benzothiazoles were synthesized and evaluated against Staphylococcus aureus (MTCC 737), Pseudomonas aeruginosa (MTCC 424), Escherichia coli (MTCC 1687), and yeast-like fungi Candida tropicalis. p-Toluidine on treatment with ammonium thiocynate formed 2-benzothiazolamines (II), which on reaction with hydrazine hydrate formed a hydrazino derivative (III). Compounds GG4 to GG8 were synthesized by reacting the hydrazine derivative with different acetophenones. All the synthesized compounds were identified by IR and 1H-NMR, and antimicrobial activity was performed on the synthesized compounds. Presence of NO2, Br, OCH3, and Cl groups to the substituted benzothiazole enhanced the antibacterial and antifungal activities. PMID:21264101

Contamination Detection and Mitigation Strategies for Unsymmetric Dimethylhydrazine/Nitrogen Tetroxide Non-Combustion Product Residues

NASA Technical Reports Server (NTRS)

Greene, Benjamin; Buchanan, Vanessa D.; Baker, David L.

2006-01-01

Dimethylamine and nitrite, which are non-combustion reaction products of unsymmetrical dimethylhydrazine (UDMH) and nitrogen tetroxide (NTO) propellants, can contaminate spacesuits during extra-vehicular activity (EVA) operations. They can react with water in the International Space Station (ISS) airlock to form N-nitrosodimethylamine (NDMA), a carcinogen. Detection methods for assessing nitrite and dimethylamine contamination were investigated. The methods are based on color-forming reactions in which intensity of color is proportional to concentration. A concept color detection kit using a commercially available presumptive field test for methamphetamine coupled with nitrite test strips was developed and used to detect dimethylamine and nitrite. Contamination mitigation strategies were also developed.

Fuels and Lubricants for Aircraft

DTIC Science & Technology

1975-02-27

probable but fundamentally possible is the use of hydrides, i.e., compounds of hydrogen "with other elements .(boranes, hydra-zine, ammonia ), alcohols...mixtures; 24. Liquid hydrogen; 25. Nitrogen hydrides and their derivatives ( ammonia , hydrazine, amines, DMH); 26. Boron, Al, Mg, Li, Be and other metals... method . For inflammation to occur, it is necessary that th’e rate of liberation of heat due to exochermic reactions in an initially heated volume of

Development of a Dosimeter System for Unsymmetrical Dimethylhydrazine, Monomethylhydrazine and Hydrazine

DTIC Science & Technology

1994-06-27

the amount of dilution air . Conditioned house- compressed air was used as the diluent. The conditioning procedure consisted of passing the house air ...unsymmetrical dlmethylhydrazine (UDMI-) in air has been developed. The dosimeter consists of a replaceable dosimeter card and a reusable...Department of Defense and NASA require air monitoring for hydrazines in areas where they are handled and/or stored. A real-time dosimeter using vanillin

Recent developments in Cope-type hydroamination reactions of hydroxylamine and hydrazine derivatives.

PubMed

Beauchemin, André M

2013-11-07

Cope-type hydroaminations are versatile for the direct amination of alkenes, alkynes and allenes using hydroxylamines and hydrazine derivatives. These reactions occur via a concerted, 5-membered cyclic transition state that is the microscopic reverse of the Cope elimination. This article focuses on recent developments, including intermolecular variants, directed reactions, and asymmetric variants using aldehydes as tethering catalysts, and their applications in target-oriented synthesis.

Hydrazine Blending and Storage Facility, Interim Response Action Implementation. Final Safety Plan

DTIC Science & Technology

1989-08-30

operators and visitors, will be required to wear a personal hydrazine dosimeter at all times. These will be available from commercial sources and/or the Naval...suspectea or carcinogenic pocen:tal for =an. -- t, :t ha a,,-cn OSL ?:L. Is I pPm or 1.3 mg/m 3 . zo pp=n4p"NIOSI. (1978) hs a oe -nded a ceiling level

Environmental Quality Research. Use of Unicellular Algae for Evaluation of Potential Aquatic Contaminants

DTIC Science & Technology

1977-11-01

Potential Aquatic Contaminants." Research was conducted by the Water Resources Laboratory, School of Engineering, University of California, Irvine...hydrazine concentration is 10 PZ/Z . This level of copper is not toxic to most aquatic organisms. In oligotrophic freshwater environments hydrazine will...AMRL-TR-77-53 ENVIRONMENTAL QUALITY RESEARCH Use of Unicellular Algae for Evaluation of Potential Aquatic Contaminants Second Annual Report JAN SCII

Noncatalytic hydrazine thruster development - 0.050 to 5.0 pounds thrust

NASA Technical Reports Server (NTRS)

Murch, C. K.; Sackheim, R. L.; Kuenzly, J. D.; Callens, R. A.

1976-01-01

Noncatalytic (thermal-decompositon) hydrazine thrusters can operate in both the pulsing and steady-state modes to meet the propulsive requirements of long-life spacecraft. The thermal decomposition mode yields higher specific impulse than is characteristic of catalytic thrusters at similar thrust levels. This performance gain is the result of higher temperature operation and a lower fraction of ammonia dissociation. Some life limiting factors of catalytic thrusters are eliminated.

Gold-catalyzed three-component annulation: efficient synthesis of highly functionalized dihydropyrazoles from alkynes, hydrazines, and aldehydes or ketones.

PubMed

Suzuki, Yamato; Naoe, Saori; Oishi, Shinya; Fujii, Nobutaka; Ohno, Hiroaki

2012-01-06

Polysubstituted dihydropyrazoles were directly obtained by a gold-catalyzed three-component annulation. This reaction consists of a Mannich-type coupling of alkynes with N,N'-disubstituted hydrazines and aldehydes/ketones followed by intramolecular hydroamination. Cascade cyclization using 1,2-dialkynylbenzene derivatives as the alkyne component was also performed producing fused tricyclic dihydropyrazoles in good yields. © 2011 American Chemical Society

Determination of Silicon in Hydrazine

NASA Technical Reports Server (NTRS)

McClure, Mark B.; Mast, Dion; Greene, Ben; Maes, Miguel J.

2006-01-01

Inductively coupled plasma-mass spectrometry (ICP-MS) is a highly sensitive technique sometimes used for the trace determination of silicon at a mass-to-charge (m/z) ratio of 28, the most abundant natural isotope of silicon. Unfortunately, ICP-MS is unable to differentiate between other sources of m/z 28 and false positive results for silicon will result when other sources of m/z 28 are present. Nitrogen was a major source of m/z 28 and contributes to the m/z 28 signal when hydrazine sample or nitric acid preservative is introduced into the plasma. Accordingly, this work was performed to develop a sample preparation step coupled with an ICP-MS analysis that minimized non-silicon sources of m/z 28. In the preparatory step of this method, the hydrazine sample was first decomposed predominately to nitrogen gas and water with copper-catalyzed hydrogen peroxide. In the analysis step, ICP-MS was used without nitric acid preservative in samples or standards. Glass, a potential source of silicon contamination, was also avoided where possible. The method was sensitive, accurate, and reliable for the determination of silicon in monopropellant grade hydrazine (MPH) in AF-E-332 elastomer leaching tests. Results for silicon in MPH were comparable to those reported in the literature for other studies.

Adsorption of phenol and hydrazine upon pristine and X-decorated (X = Sc, Ti, Cr and Mn) MoS2 monolayer

NASA Astrophysics Data System (ADS)

Wang, Meiyan; Wang, Wei; Ji, Min; Cheng, Xinlu

2018-05-01

Using density functional theory (DFT), we present a theoretical investigation of phenol (C6H5OH) and hydrazine (N2H4) on pristine and decorated MoS2 monolayer. In our work, we first focus on the interactions between several metal atoms and MoS2 monolayer and then choose the MoS2 nanosheet decorated by Sc, Ti, Cr and Mn to be the substrate. Furthermore, the properties of phenol and N2H4 on pure and X-doped (X = Sc, Ti, Cr and Mn) MoS2 base materials are discussed in terms of adsorption energy, adsorption distance, charge transfer, charge density difference, HOMO and LUMO molecular orbitals and density of states (DOS). The results predict that the adsorption of phenol and hydrazine upon X-decorated MoS2 monolayers are more favorable than the adsorption on isolated ones, which demonstrating that Sc, Ti, Cr and Mn doping help to improve the adsorption abilities. Calculations also show shorter adsorption distance and more charge transfer for Sc-, Ti-, Cr- and Mn-doped systems than the pristine one. The results confirm that X-doped MoS2 monolayer can be used as effective and potential adsorbents for toxic phenol and hydrazine.

Sensing strategies for toxic vapor detection

NASA Technical Reports Server (NTRS)

Mottola, Horacio A.

1995-01-01

This work was motivated by the recommendations of the American Conference of Governmental Industrial Hygienists (ACGIH) that threshold limits for hydrazine, H2N-NH2 in air be lowered from 100 to 10 parts-per-billion (ppb) concentration levels. Hydrazine is one of the high-energy propellants used in large volumes in Space Shuttle, Titan, payloads, and other aerospace operations. Since analytical methods presently available for hydrazine detection and/or determination do not satisfy such low levels of detection, the ultimate goal of this research is the development and characterization of a portable and compact chemical sensor ideally capable to detect (in real time) 1 ppb of hydrazine, continuously and reversibly. The laboratory prototype developed as part of this project is comprised of: (1) a reactor part in which H2N-NH2 reacts, generating chemiluminescence emission, with tris(2,2'-bipyridine)ruthenium(III), which is immobilized on an ion-exchange polymeric materials of a perfluorinated hydrocarbon containing sulfonate groups as exchange centers (Nafion); (2) an electrochemical three-electrode cell posed at a potential at which the immobilized ruthenium complex could be reoxidized to the 3-oxidation state (as to provide reversible and continuous detection); and (3) a low power consumption photomultiplier tube to collect and quantitatively integrate the emitted photons with the help of auxiliary electronics and readout device.

Hydrocarbon-Seeded Ignition System for Small Spacecraft Thrusters Using Ionic Liquid Propellants

NASA Technical Reports Server (NTRS)

Whitmore, Stephen A.; Merkley, Daniel P.; Eilers, Shannon D.; Taylor, Terry L.

2013-01-01

"Green" propellants based on Ionic-liquids (ILs) like Ammonium DiNitramide and Hydroxyl Ammonium Nitrate have recently been developed as reduced-hazard replacements for hydrazine. Compared to hydrazine, ILs offer up to a 50% improvement in available density-specific impulse. These materials present minimal vapor hazard at room temperature, and this property makes IL's potentially advantageous for "ride-share" launch opportunities where hazards introduced by hydrazine servicing are cost-prohibitive. Even though ILs present a reduced hazard compared to hydrazine, in crystalline form they are potentially explosive and are mixed in aqueous solutions to buffer against explosion. Unfortunately, the high water content makes IL-propellants difficult to ignite and currently a reliable "coldstart" capability does not exist. For reliable ignition, IL-propellants catalyst beds must be pre-heated to greater than 350 C before firing. The required preheat power source is substantial and presents a significant disadvantage for SmallSats where power budgets are extremely limited. Design and development of a "micro-hybrid" igniter designed to act as a "drop-in" replacement for existing IL catalyst beds is presented. The design requires significantly lower input energy and offers a smaller overall form factor. Unlike single-use "squib" pyrotechnic igniters, the system allows the gas generation cycle to be terminated and reinitiated on demand.

Hydrazide and hydrazine reagents as reactive matrices for MALDI-MS to detect gaseous aldehydes.

PubMed

Shigeri, Yasushi; Ikeda, Shinya; Yasuda, Akikazu; Ando, Masanori; Sato, Hiroaki; Kinumi, Tomoya

2014-08-01

The reagents 19 hydrazide and 14 hydrazine were examined to function as reactive matrices for matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) to detect gaseous aldehydes. Among them, two hydrazide (2-hydroxybenzohydrazide and 3-hydroxy-2-naphthoic acid hydrazide) and two hydrazine reagents [2-hydrazinoquinoline and 2,4-dinitrophenylhydrazine (DNPH)] were found to react efficiently with carbonyl groups of gaseous aldehydes (formaldehyde, acetaldehyde and propionaldehyde); these are the main factors for sick building syndrome and operate as reactive matrices for MALDI-MS. Results from accurate mass measurements by JMS-S3000 Spiral-TOF suggested that protonated ion peaks corresponding to [M + H](+) from the resulting derivatives were observed in all cases with the gaseous aldehydes in an incubation, time-dependent manner. The two hydrazide and two hydrazine reagents all possessed absorbances at 337 nm (wavelength of MALDI nitrogen laser), with, significant electrical conductivity of the matrix crystal and functional groups, such as hydroxy group and amino group, being important for desorption/ionization efficiency in MALDI-MS. To our knowledge, this is the first report that gaseous molecules could be derivatized and detected directly in a single step by MALDI-MS using novel reactive matrices that were derivatizing agents with the ability to enhance desorption/ionization efficiency. Copyright © 2014 John Wiley & Sons, Ltd.

Material Compatability with Threshold Limit Value Levels of Monomethyl Hydrazine

DTIC Science & Technology

1988-10-26

supply was house- compressed air conditioned by passing through a series of demisters, a hot Hopcalite catalyst bed, a reciprocating dual-tower...recorded. At the end of a test, the tubing was rinsed with methanol and dried with compressed breathing air . Cleaning the tubing material between tests had...niecessary and identify by block wbr -’Materials were evaluated for potential use as ambient air sample lines for hydrazines. Fluorinated poly- mers

The use of hydrazine as an alternate source of energy

NASA Technical Reports Server (NTRS)

Carvalho, J. A., Jr.; Bressan, C.; Ferreira, J. L.

1984-01-01

The potentials of using hydrazine as an alternative source of energy was studied. Three chemical reactions are considered: oxidation with air, oxidation with hydrogen peroxide, and thermocatalytic decomposition. Performance data of gasoline, ethylic alcohol, and propane are compared. An item about the NO(x) emissions by the various investigated reactions is included. Promising results are shown, mainly those regarding the available energy per unit volume of unburned gases (vaporized fuel and oxidizer).

Synthesis of azines in solid state: reactivity of solid hydrazine with aldehydes and ketones.

PubMed

Lee, Byeongno; Lee, Kyu Hyung; Cho, Jaeheung; Nam, Wonwoo; Hur, Nam Hwi

2011-12-16

Highly conjugated azines were prepared by solid state grinding of solid hydrazine and carbonyl compounds such as aldehydes and ketones, using a mortar and a pestle. Complete conversion to the azine product is generally achieved at room temperature within 24 h, without using solvents or additives. The solid-state reactions afford azines as the sole products with greater than 97% yield, producing only water and carbon dioxide as waste.

Active Hydrazine Vapor Sampler (AHVS)

NASA Technical Reports Server (NTRS)

Young, Rebecca C.; Mcbrearty, Charles F.; Curran, Daniel J.

1993-01-01

The Active Hydrazine Vapor Sampler (AHVS) was developed to detect vapors of hydrazine (HZ) and monomethylhydrazine (MMH) in air at parts-per-billion (ppb) concentration levels. The sampler consists of a commercial personal pump that draws ambient air through paper tape treated with vanillin (4-hydroxy-3-methoxybenzaldehyde). The paper tape is sandwiched in a thin cardboard housing inserted in one of the two specially designed holders to facilitate sampling. Contaminated air reacts with vanillin to develop a yellow color. The density of the color is proportional to the concentration of HZ or MMH. The AHVS can detect 10 ppb in less than 5 minutes. The sampler is easy to use, low cost, and intrinsically safe and contains no toxic material. It is most beneficial for use in locations with no laboratory capabilities for instrumentation calibration. This paper reviews the development, laboratory test, and field test of the device.

Catalyst comprising Ir or Ir and Ru for hydrazine decomposition

NASA Technical Reports Server (NTRS)

Armstrong, Warren E. (Inventor); Voge, Hervey H. (Inventor); Ryland, Lloyd B. (Inventor)

1978-01-01

A catalyst for hydrazine decomposition consisting essentially of a carrier having a pore volume of at least 0.1 cubic centimeters per gram and a specific surface area, measured in square meters per gram, equal to 195 (C.sub.p + 0.013 + 0.736 V.sub.p) where C.sub.p is the specific heat capacity of the carrier at about 25.degree. C in calories per gram per degree and V.sub.p is the pore volume of the carrier in cubic centimeters per gram and metal of the group consisting of iridium, and mixtures consisting of iridium and ruthenium deposited on said carrier in an amount between 20% and about 40% by weight of the catalyst and distributed through the pores thereof in discrete particles sufficiently separated from each other so that they do not sinter or fuse together when the catalyst is at hydrazine decomposition temperature.

A two-dimensional ZnII coordination polymer constructed from benzene-1,2,3-tricarboxylic acid and N,N'-bis[(pyridin-4-yl)methylidene]hydrazine.

PubMed

Wang, Xiangfei; Yang, Fang; Tang, Meng; Yuan, Limin; Liu, Wenlong

2015-07-01

The hydrothermal synthesis of the novel complex poly[aqua(μ4-benzene-1,2,3-tricarboxylato)[μ2-4,4'-(hydrazine-1,2-diylidenedimethanylylidene)dipyridine](μ3-hydroxido)dizinc(II)], [Zn(C9H3O6)(OH)(C12H10N4)(H2O)]n, is described. The benzene-1,2,3-tricarboxylate ligand connects neighbouring Zn4(OH)2 secondary building units (SBUs) producing an infinite one-dimensional chain. Adjacent one-dimensional chains are connected by the N,N'-bis[(pyridin-4-yl)methylidene]hydrazine ligand, forming a two-dimensional layered structure. Adjacent layers are stacked to generate a three-dimensional supramolecular architecture via O-H...O hydrogen-bond interactions. The thermal stability of this complex is described and the complex also appears to have potential for application as a luminescent material.

Quantification of transformation products of rocket fuel unsymmetrical dimethylhydrazine in soils using SPME and GC-MS.

PubMed

Bakaikina, Nadezhda V; Kenessov, Bulat; Ul'yanovskii, Nikolay V; Kosyakov, Dmitry S

2018-07-01

Determination of transformation products (TPs) of rocket fuel unsymmetrical dimethylhydrazine (UDMH) in soil is highly important for environmental impact assessment of the launches of heavy space rockets from Kazakhstan, Russia, China and India. The method based on headspace solid-phase microextraction (HS SPME) and gas chromatography-mass spectrometry is advantageous over other known methods due to greater simplicity and cost efficiency. However, accurate quantification of these analytes using HS SPME is limited by the matrix effect. In this research, we proposed using internal standard and standard addition calibrations to achieve proper combination of accuracies of the quantification of key TPs of UDMH and cost efficiency. 1-Trideuteromethyl-1H-1,2,4-triazole (MTA-d3) was used as the internal standard. Internal standard calibration allowed controlling matrix effects during quantification of 1-methyl-1H-1,2,4-triazole (MTA), N,N-dimethylformamide (DMF), and N-nitrosodimethylamine (NDMA) in soils with humus content < 1%. Using SPME at 60 °C for 15 min by 65 µm Carboxen/polydimethylsiloxane fiber, recoveries of MTA, DMF and NDMA for sandy and loamy soil samples were 91-117, 85-123 and 64-132%, respectively. For improving the method accuracy and widening the range of analytes, standard addition and its combination with internal standard calibration were tested and compared on real soil samples. The combined calibration approach provided greatest accuracies for NDMA, DMF, N-methylformamide, formamide, 1H-pyrazole, 3-methyl-1H-pyrazole and 1H-pyrazole. For determination of 1-formyl-2,2-dimethylhydrazine, 3,5-dimethylpyrazole, 2-ethyl-1H-imidazole, 1H-imidazole, 1H-1,2,4-triazole, pyrazines and pyridines, standard addition calibration is more suitable. However, the proposed approach and collected data allow using both approaches simultaneously. Copyright © 2018 Elsevier B.V. All rights reserved.

Green Applications for Space Power Project

NASA Technical Reports Server (NTRS)

Robinson, Joel (Principal Investigator)

2014-01-01

Spacecraft propulsion and power for many decades has relied on Hydrazine monopropellant technology for auxiliary power units (APU), orbital circularization, orbit raising/lowering and attitude control. However, Hydrazine is toxic and therefore requires special ground handling procedures to ensure launch crew safety. The Swedish Company ECAPS has developed a technology based upon the propellant Ammonium Dinitramide (ADN) that offers higher performance, higher density and reduced ground handling support than Hydrazine. This blended propellant is called LMP-103S. Currently, the United States Air Force (USAF) is pursuing a technology based on Hydroxyl Ammonium Nitrate (HAN, otherwise known as AF-M315E) with industry partners Aerojet and Moog. Based on the advantages offered by these propellants, MSFC should explore powering APU's with these propellants. Due to the availability of space hardware, the principal investigator has found a collection of USAF hardware, that will act as a surrogate, which operates on a Hydrazine derivative. The F-16 fighter jet uses H-70 or 30% diluted Hydrazine for an Emergency Power Unit (EPU) which supplies power to the plane. The PI has acquired two EPU's from planes slated for destruction at the Davis Monthan AFB. This CIF will include a partnership with 2 other NASA Centers who are individually seeking seed funds from their respective organizations: Kennedy Space Center (KSC) and Dryden Flight Research Center (DFRC). KSC is preparing for future flights from their launch pads that will utilize green propellants and desire a low-cost testbed in which to test and calibrate new leak detection sensors. DFRC has access to F-16's which can be used by MSFC & KSC to perform a ground test that demonstrates emergency power supplied to the jet. Neither of the green propellant alternatives have been considered nor evaluated for an APU application. Work has already been accomplished to characterize and obtain the properties of these 2 propellants. However, the spacecraft are using existing leak detection sensors that are typically used for Hydrazine. Using these green propellants for the APU application requires decrementing their TRL down to 3. This task would aim to establish a TRL of 4 at conclusion by showing a proof of concept with a KSC-instrumented EPU asset at the MSFC Component Development Area (CDA). The task to accomplish this is called Green Application for Space Power or GRASP.

Polypyrrole-derived nitrogen and oxygen co-doped mesoporous carbons as efficient metal-free electrocatalyst for hydrazine oxidation.

PubMed

Meng, Yuying; Zou, Xiaoxin; Huang, Xiaoxi; Goswami, Anandarup; Liu, Zhongwu; Asefa, Tewodros

2014-10-08

We demonstrate that polypyrrole-derived nitrogen and oxygen co-doped mesoporous carbons can serve as efficient, metal-free electrocatalysts for hydrazine oxidation reaction, with low overpotential and high current density. The materials' structures and the nature and type of their included dopants, which can be controlled by varying the synthetic conditions, can affect the electrocatalytic properties of the materials. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Proceedings of the Conference on Environmental Toxicology (9th), 28, 29, and 30 March 1979

DTIC Science & Technology

1979-08-01

collected on all persons by the method of saline induction. All samples were analyzed in the laboratory of Dr. Geno Saccomanno, Grand Junction, Colorado...hydrazine was labeled by 1 4 C-methyl-methionine to a greater extent than in saline -treated animals. In the current studies, young adult fasted male...METHIONINE: COMPARISON TO METHYLATION IN HYDRAZINE- AND MMH-TREATED RATS 7-Methylguanine Content Treatment (pMole/Mole Guanine) Saline 0 (None

An Assessment of Hydrazine, Hydrazine Hydrate and Liquid Ammonia as Fuels for Rocket Propulsion

DTIC Science & Technology

1949-08-01

oxide, hyponitrites, or potassium nitrososulphite; decomposition of aminogunnidine; hydrolysis of bis-dinzo acetic acid; and nlso n cyclic process due to... Dehydration of hydrnzinc hydrnte. This may be carried out with caustic alknli, quick- lime or baryto. The method is probably suitable for laboratory scale...certaini that it can be opernted under safe conditions. These disadvontages should not be so formidable if only a partial dehydration were desired. In this

Monitoring Calcium in Trout Eggs Exposed to Hydrazine.

DTIC Science & Technology

1981-07-10

differentiation processes (Chapman, 1980). The high level of calcium in the notochord can be attributed to poor circulation which is characteristic of this...healthy muscle of the same individual. The notochord of the 8.0 mg/P group showed a higher calcium level than the control group. The chorion did not...calcium can alter the process . The above would suggest that even if some hydrazine is converted to N2 and thereby produce the gas bubble disease

Interactions of Hydrazine and of Hydrazine Derivatives with Soil Constituents and with Soils

DTIC Science & Technology

1984-08-23

vigorously. After flocs which formed on addition of alkali had redissolved a homogeneous dark red solution (pH 2.0) was obtained. This solution was allowed to...collected fractions of the eluate. Scintillation techniques (Smedley, 1978), atomic absorption and radioisotopic labelling techniques (Hartmann, 1981), and...but significantly less exothermic in the cases of the alkali -earth than the alkali metals. The heat of hydration of the divalent cations is greater than

R&D of Energetic Ionic Liquids

DTIC Science & Technology

2011-11-01

Ammonia 3-6 H2O balance Properties LMP-103S AF - M315E Hydrazine Ispvac,lbf sec/lbm (e = 50:1 Pc = 300 psi) 252 (theor.) 235 (del) 266...Distribution A: Public Release, Distribution unlimited. AF - M315E is US Air Force IL-Based Monopropellant •Significant physical property and performance...6 Toxicity Assessment of AF - M315E Toxicity Testing Results PROPERTY AF - M315E HYDRAZINE LD50 (rat), mg/kg 550 60 Dermal Irritation (rabbit

Performance characterization of a low power hydrazine arcjet

NASA Technical Reports Server (NTRS)

Knowles, S. C.; Smith, W. W.; Curran, F. M.; Haag, T. W.

1987-01-01

Hydrazine arcjets, which offer substantial performance advantages over alternatives in geosynchronous satellite stationkeeping applications, have undergone startup, materials compatibility, lifetime, and power conditioning unit design issues. Devices in the 1000-3000 W output range have been characterized for several different electrode configurations. Constrictor length and diameter, electrode gap setting, and vortex strength have been parametrically studied in order to ascertain the influence of each on specific impulse and efficiency; specific impulse levels greater than 700 sec have been achieved.

Development of a sensitive monitor for hydrazine

NASA Technical Reports Server (NTRS)

Eiceman, Gary A.; Limero, Thomas; James, John T.

1991-01-01

The development of hand-held, ambient-temperature instruments that utilize ion mobility spectrometry (IMS) in the detection of hydrazine and monomethylhydrazine is reviewed. A development effort to eliminate ammonia interference through altering the ionization chemistry, based on adding 5-nonanone as dopant in the ionization region of the IMS, is presented. Calibration of this instrument conducted before and after STS-37 revealed no more than a 5 percent difference between calibration curves, without any appreciable loss of equipment function.

Advanced Compatibility Characterization Of AF-M315E With Spacecraft Propulsion System Materials Project

NASA Technical Reports Server (NTRS)

McClure, Mark B.; Greene, Benjamin

2014-01-01

All spacecraft require propulsion systems for thrust and maneuvering. Propulsion systems can be chemical, nuclear, electrical, cold gas or combinations thereof. Chemical propulsion has proven to be the most reliable technology since the deployment of launch vehicles. Performance, storability, and handling are three important aspects of liquid chemical propulsion. Bipropellant systems require a fuel and an oxidizer for propulsion, but monopropellants only require a fuel and a catalyst for propulsion and are therefore simpler and lighter. Hydrazine is the state of the art propellant for monopropellant systems, but has drawbacks because it is highly hazardous to human health, which requires extensive care in handling, complex ground ops due to safety and environmental considerations, and lengthy turnaround times for reusable spacecraft. All users of hydrazine monopropellant must contend with these issues and their associated costs. The development of a new monopropellant, intended to replace hydrazine, has been in progress for years. This project will apply advanced techniques to characterize the engineering properties of materials used in AF-M315E propulsion systems after propellant exposure. AF-M315E monopropellant has been selected HQ's Green Propellant Infusion Mission (GPIM) to replace toxic hydrazine for improved performance and reduce safety and health issues that will shorten reusable spacecraft turn-around time. In addition, this project will fundamentally strengthen JSC's core competency to evaluate, use and infuse liquid propellant systems.

Prototype development and test results of a continuous ambient air monitoring system for hydrazine at the 10 ppb level

NASA Technical Reports Server (NTRS)

Meneghelli, Barry; Parrish, Clyde; Barile, Ron; Lueck, Dale E.

1995-01-01

A Hydrazine Vapor Area Monitor (HVAM) system is currently being field tested as a detector for the presence of hydrazine in ambient air. The MDA/Polymetron Hydrazine Analyzer has been incorporated within the HVAM system as the core detector. This analyzer is a three-electrode liquid analyzer typically used in boiler feed water applications. The HVAM system incorporates a dual-phase sample collection/transport method which simultaneously pulls ambient air samples containing hydrazine and a very dilute sulfuric acid solution (0.0001 M) down a length of 1/4 inch outside diameter (OD) tubing from a remote site to the analyzer. The hydrazine-laden dilute acid stream is separated from the air and the pH is adjusted by addition of a dilute caustic solution to a pH greater than 10.2 prior to analysis. Both the dilute acid and caustic used by the HVAM are continuously generated during system operation on an "as needed" basis by mixing a metered amount of concentrated acid/base with dilution water. All of the waste water generated by the analyzer is purified for reuse by Barnstead ion-exchange cartridges so that the entire system minimizes the generation of waste materials. The pumping of all liquid streams and mixing of the caustic solution and dilution water with the incoming sample are done by a single pump motor fitted with the appropriate mix of peristaltic pump heads. The signal to noise (S/N) ratio of the analyzer has been enhanced by adding a stirrer in the MDA liquid cell to provide mixing normally generated by the high liquid flow rate designed by the manufacturer. An onboard microprocessor continuously monitors liquid levels, sample vacuum, and liquid leak sensors, as well as handles communications and other system functions (such as shut down should system malfunctions or errors occur). The overall system response of the HVAM can be automatically checked at regular intervals by measuring the analyzer response to a metered amount of calibration standard injected into the dilute acid stream. The HVAM system provides two measurement ranges (threshold limit value (TLV): 10 to 1000 parts per billion (ppb)/LEAK: 100 ppb to 10 parts per million (ppm)). The LEAK range is created by dilution of the sulfuric acid/hydrazine liquid sample with pure water. This dual range capability permits the analyzer to quantify ambient air samples whose hydrazine concentrations range from 10 ppb to as high as 10 ppm. The laboratory and field prototypes have demonstrated total system response times on the order of 10 to 12 minutes for samples ranging from 10 to 900 ppb in the lLV mode and is greater than 2 minutes for samples ranging from 100 to 1300 ppb in the LEAK mode. Service intervals of over 3 months have been demonstrated for continuous 24 hour/day, 7 day/week usage. The HVAM is made up of a purged cabinet that contains power supplies, RS422 signal transmission capabilities, a UPS, an on-site warning system, and a Line Replaceable Unit (LRU). The LRU includes all of the liquid flow system, the analyzer, the control/data system microprocessor and assorted flow and liquid-level sensors. The LRU is mounted on a track slide system so it can be serviced inplace or totally removed and quickly exchanged with another calibrated unit, thus minimizing analyzer downtime. Once an LRU is removed from an analyzer enclosure, it can be brought to a laboratory facility for complete calibration and periodic maintenance.

Space Shuttle Upgrades Advanced Hydraulic Power System

NASA Technical Reports Server (NTRS)

2004-01-01

Three Auxiliary Power Units (APU) on the Space Shuttle Orbiter each provide 145 hp shaft power to a hydraulic pump which outputs 3000 psi hydraulic fluid to 41 hydraulic actuators. A hydrazine fuel powered APU utilized throughout the Shuttle program has undergone many improvements, but concerns remain with flight safety, operational cost, critical failure modes, and hydrazine related hazards. The advanced hydraulic power system (AHPS), also known as the electric APU, is being evaluated as an upgrade to replace the hydrazine APU. The AHPS replaces the high-speed turbine and hydrazine fuel supply system with a battery power supply and electric motor/pump that converts 300 volt electrical power to 3000 psi hydraulic power. AHPS upgrade benefits include elimination of toxic hydrazine propellant to improve flight safety, reduction in hazardous ground processing operations, and improved reliability. Development of this upgrade provides many interesting challenges and includes development of four hardware elements that comprise the AHPS system: Battery - The battery provides a high voltage supply of power using lithium ion cells. This is a large battery that must provide 28 kilowatt hours of energy over 99 minutes of operation at 300 volts with a peak power of 130 kilowatts for three seconds. High Voltage Power Distribution and Control (PD&C) - The PD&C distributes electric power from the battery to the EHDU. This 300 volt system includes wiring and components necessary to distribute power and provide fault current protection. Electro-Hydraulic Drive Unit (EHDU) - The EHDU converts electric input power to hydraulic output power. The EHDU must provide over 90 kilowatts of stable, output hydraulic power at 3000 psi with high efficiency and rapid response time. Cooling System - The cooling system provides thermal control of the Orbiter hydraulic fluid and EHDU electronic components. Symposium presentation will provide an overview of the AHPS upgrade, descriptions of the four hardware elements, and a summary of development results to date.

Catalytic oxidation of dimethyl ether

DOEpatents

Zelenay, Piotr; Wu, Gang; Johnston, Christina M.; Li, Qing

2016-05-10

A composition for oxidizing dimethyl ether includes an alloy supported on carbon, the alloy being of platinum, ruthenium, and palladium. A process for oxidizing dimethyl ether involves exposing dimethyl ether to a carbon-supported alloy of platinum, ruthenium, and palladium under conditions sufficient to electrochemically oxidize the dimethyl ether.

Novel Combination of Prebiotics Galacto-Oligosaccharides and Inulin-Inhibited Aberrant Crypt Foci Formation and Biomarkers of Colon Cancer in Wistar Rats.

PubMed

Qamar, Tahir Rasool; Syed, Fatima; Nasir, Muhammad; Rehman, Habib; Zahid, Muhammad Nauman; Liu, Rui Hai; Iqbal, Sanaullah

2016-08-01

The selectivity and beneficial effects of prebiotics are mainly dependent on composition and glycosidic linkage among monosaccharide units. This is the first study to use prebiotic galacto-oligosaccharides (GOS) that contains β-1,6 and β-1,3 glycosidic linkages and the novel combination of GOS and inulin in cancer prevention. The objective of the present study is to explore the role of novel GOS and inulin against various biomarkers of colorectal cancer (CRC) and the incidence of aberrant crypt foci (ACF) in a 1,2-dimethyl hydrazine dihydrochloride (DMH)-induced rodent model. Prebiotic treatments of combined GOS and inulin (57 mg each), as well as individual doses (GOS: 76-151 mg; inulin 114 mg), were given to DMH-treated animals for 16 weeks. Our data reveal the significant preventive effect of the GOS and inulin combination against the development of CRC. It was observed that inhibition of ACF formation (55.8%) was significantly (p ≤ 0.05) higher using the GOS and inulin combination than GOS (41.4%) and inulin (51.2%) treatments alone. This combination also rendered better results on short-chain fatty acids (SCFA) and bacterial enzymatic activities. Dose-dependent effects of prebiotic treatments were also observed on cecum and fecal bacterial enzymes and on SCFA. Thus, this study demonstrated that novel combination of GOS and inulin exhibited stronger preventive activity than their individual treatments alone, and can be a promising strategy for CRC chemoprevention.

Hydrazine Blending and Storage Facility, Wastewater Treatment and Decommissioning Assessment. Technical Plan, Version 3.2

DTIC Science & Technology

1988-04-01

o CHEMICAL TREATMENT - CHLORINE (VARIOUS FORMS) AND CHLORINE/ULTRAVIOLET LIGHT (UV) - OZONE AND OZONE/UV - PERMANGANATE - HYDROGEN PEROXIDE AND...and placed in drums, rail cars or trucks (Hazard 3 Abatement Plan, 1982). The existing hydrazine blending facility area is a limited access site which...Area 40’-0" x 26’-0" Volume 44,000 gallons Function Receive wastewater and stormwater runoff m Construction Material Concrete 7. Building 759 Size 40’-0

Laboratory Development of a Passive Sampling Device for Hydrazines in Ambient Air

DTIC Science & Technology

1990-05-30

of dilution air . Conditioned house- compressed air is used as the diluent. The conditioning procedure consists of passing the house air through a...Device N4 for Hydrazines in Ambient Air P. A. TAFFE,* K. P. CROSSMAN,* S. L. ROSE-PEHRSSON, AND J. R. WYATT 0 Chemistry Dynamics and Diagnostic Branch...Ambient Air 6. AUTHOR(S) Taffe,* P. A., Crossman,* K. P., Wyatt, J. R., and Rose-Pehrsson, S. L. 7. PERFORMING ORGANIZATION NAME(S) AND ADORESS(ES) 8

Simple assembly of polysubstituted pyrazoles and isoxazoles via ring closure-ring opening domino reaction of 3-acyl-4,5-dihydrofurans with hydrazines and hydroxylamine.

PubMed

Chagarovskiy, Alexey O; Budynina, Ekaterina M; Ivanova, Olga A; Rybakov, Victor B; Trushkov, Igor V; Melnikov, Mikhail Ya

2016-03-14

A convenient general approach to 2-(pyrazol-4-yl)- and 2-(isoxazol-4-yl)ethanols based on the Brønsted acid-initiated reaction of 3-acyl-4,5-dihydrofurans with hydrazines or hydroxylamine was developed. Further transformation of the alcohol moiety in 2-(pyrazolyl)ethanols affording 2-(pyrazolyl)ethylamine as potent bioactive compounds as well as pyrazole-substituted derivatives of antitumor alkaloid crispine A was elaborated.

Combined effects of hydrazine exposure and endurance testing on solenoid-actuated valve performance

NASA Technical Reports Server (NTRS)

Hagler, R., Jr.

1974-01-01

Results are presented from a test program which was conducted to assess the capability of various solenoid-actuated valve design concepts to provide performance characteristics commensurate with long-duration (ten-year) missions to explore the outer planets. The valves were installed in a hydrazine flow test setup and periodically cycled during a nine-month test period under test conditions comparable to anticipated mission operating conditions. In situ valve performance was periodically determined, and leakage was continuously monitored.

Studies on the Mechanism of Action of Hydrazine-Induced Methylation of DNA Guanne

DTIC Science & Technology

1984-10-03

potent methylating agent , diazomethane (-CH -N+-N). Several in vivo studies were carried out to determine the role of aldehydes in the alkylation of DNA...methylating agent available to interact with DNA. If such a mechanism occurs, it may explain why disulfiram appears to inhibit the alkylation of DNA...a much slower/poorer alkylating agent for DNA. Effect of the 1-Carbon Pool on DNA Methylation in Hydrazine Toxicity: In Vitro In vitro studies were

Attitude Control Propulsion Components, Volume 1

NASA Technical Reports Server (NTRS)

1974-01-01

Effort was made to include as much engineering information on each component as possible, consistent with usefulness and catalog size limitations. The contents of this catalog contain components which were qualified for use with spacecraft monopropellant hydrazine and inert gas attitude control systems. Thrust ranges up to 44.5 N (10.0 lbf) for hydrazine and inert gas sytems were considered. Additionally, some components qualified for uses other than spacecraft attitude control are included because they are suitable for use in attitude controls systems.

Fast Hydrazone Reactants: Electronic and Acid/Base Effects Strongly Influence Rate at Biological pH

PubMed Central

Kool, Eric T.; Park, Do-Hyoung; Crisalli, Pete

2013-01-01

Kinetics studies with structurally varied aldehydes and ketones in aqueous buffer at pH 7.4 reveal that carbonyl compounds with neighboring acid/base groups form hydrazones at accelerated rates. Similarly, tests of a hydrazine with a neighboring carboxylic acid group show that it also reacts at an accelerated rate. Rate constants for the fastest carbonyl/hydrazine combinations are 2–20 M−1sec−1, which is faster than recent strain-promoted cycloaddition reactions. PMID:24224646

Ammonia and hydrazine. Transition-metal-catalyzed hydroamination and metal-free catalyzed functionalization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bertrand, Guy

2012-06-29

The efficient and selective preparation of organic molecules is critical for mankind. For the future, it is of paramount importance to find catalysts able to transform abundant and cheap feedstocks into useful compounds. Acyclic and heterocyclic nitrogen-containing derivatives are common components of naturally occurring compounds, agrochemicals, cosmetics, and pharmaceuticals; they are also useful intermediates in a number of industrial processes. One of the most widely used synthetic strategies, allowing the formation of an N-C bond, is the addition of an N-H bond across a carbon-carbon multiple bond, the so-called hydroamination reaction. This chemical transformation fulfills the principle of “green chemistry”more » since it ideally occurs with 100% atom economy. Various catalysts have been found to promote this reaction, although many limitations remain; one of the most prominent is the lack of methods that permit the use of NH 3 and NH 2NH 2 as the amine partners. In fact, ammonia and hydrazine have rarely succumbed to homogeneous catalytic transformations. Considering the low cost and abundance of ammonia (136 million metric tons produced in 2011) and hydrazine, catalysts able to improve the reactivity and selectivity of the NH 3- and NH 2NH 2-hydroamination reaction, and more broadly speaking the functionalization of these chemicals, are highly desirable. In the last funded period, we discovered the first homogeneous catalysts able to promote the hydroamination of alkynes and allenes with ammonia and the parent hydrazine. The key feature of our catalytic systems is that the formation of catalytically inactive Werner complexes is reversible, in marked contrast to most of the known ammonia and hydrazine transition metal complexes. This is due to the peculiar electronic properties of our neutral ancillary ligands, especially their strong donating capabilities. However, our catalysts currently require high temperatures and long reaction times. To address this issue, we have developed several new families of carbon- and boron-based ligands, which are even better donors. The corresponding metal complexes (particularly gold, rhodium, iridium, and ruthenium) of all these species will be tested in the Markovnikov and anti-Markovnikov hydroamination of alkynes, allenes, and also alkenes with ammonia and hydrazine. We will also develop metal-free catalytic processes for the functionalization of ammonia and hydrazine. By possessing both a lone pair of electrons and an accessible vacant orbital, singlet carbenes resemble and can mimic the chemical behavior of transition metals. Our preliminary results demonstrate that specially designed carbenes can split the N–H bond of ammonia by an initial nucleophilic activation that prevents the formation of Lewis acid-base adducts, which is the major hurdle for the transition metal catalyzed functionalization of NH 3. The use of purely organic compounds as catalysts will eliminate the major drawbacks of transition-metal-catalysis technology, which are the excessive cost of metal complexes (metal + ligands) and in many cases the toxicity of the metal.« less

Synthesis and Free Radical Scavenging Activity of New Hydroxybenzylidene Hydrazines.

PubMed

Sersen, Frantisek; Gregan, Fridrich; Kotora, Peter; Kmetova, Jarmila; Filo, Juraj; Loos, Dusan; Gregan, Juraj

2017-05-29

Hydroxybenzylidene hydrazines exhibit a wide spectrum of biological activities. Here, we report synthesis and free radical scavenging activity of nine new N-(hydroxybenzylidene)-N'-[2,6-dinitro-4-(trifluoromethyl)]phenylhydrazines. The chemical structures of these compounds were confirmed by 1H-NMR, 13C-NMR, 19F-NMR, IR spectroscopy, LC-MS, and elemental analysis. The prepared compounds were tested for their activity to scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH), galvinoxyl radical (GOR), and 2,2'-azino-bis(3-ethylbenzothiazoline)-6-sulphonic acid (ABTS) radicals. The free radical scavenging activity expressed as SC50 values of these compounds varied in a wide range, from a strong to no radical scavenging effect. The most effective radical scavengers were hydroxybenzylidene hydrazines containing three hydroxyl groups in the benzylidene part of their molecules. The prepared compounds were also tested for their activity to inhibit photosynthetic electron transport in spinach chloroplasts. IC50 values of these compounds varied in wide range, from an intermediate to no inhibitory effect.

The Effect of Reduction Potential on the Generation of the Perylene Diimide Radical Anions

NASA Astrophysics Data System (ADS)

Zhao, Y. Z.; Li, K. X.; Ding, S. Y.; Zhu, M.; Ren, H. P.; Ma, Q.; Guo, Z.; Tian, S. P.; Zhang, H. Q.; Miao, Z. C.

2018-07-01

Perylene diimide derivatives (PDIs) with different substituents in the bay positions (Un-PDI, DFPDI and THBPDI) were chosen in this report to investigate the effect of potential on the reduction of PDIs through base (hydrazine, 1,2-ethanediamine and triethylamine)-driven keto-enol anion tautomerism. The reduction potentials (PDI/PDI•-) of these compounds determined via cyclic voltammetry are -0.51, ‒0.34, and -0.098 V for Un-PDI, DFPDI, and THBPDI, respectively. The reduction of Un-PDI, DFPDI and THBPDI by hydrazine can produce corresponding radical anions and dianions, but the volume of hydrazine added at which the radicals started to appear is different and depends on their reduction potential. The similar phenomenon was observed using 1,2-ethylenediamine and triethylamine. However, only the radical anion was obtained even in a large excess of 1,2-ethanediamine or triethylamine. Moreover, the reduction of these PDIs with different bases added in the same amount was investigated, and the correlation with their basicity was shown.

Design, testing, fabrication and launch support of a liquid chemical barium release payload (utilizing the liquid fluorine-barium salt/hydrazine system)

NASA Technical Reports Server (NTRS)

Stokes, C. S.; Smith, E. W.; Murphy, W. J.

1972-01-01

A payload was designed which included a cryogenic oxidizer tank, a fuel tank, and burner section. Release of 30 lb of chemicals was planned to occur in 2 seconds at the optimum oxidizer to fuel ratio. The chemicals consisted of 17 lb of liquid fluorine oxidizer and 13 lb of hydrazine-barium salt fuel mixture. The fuel mixture was 17% barium chloride, 16% barium nitrate, and 67% hydrazine, and contained 2.6 lb of available barium. Two significant problem areas were resolved during the program: explosive valve development and burner operation. The release payload was flight tested, from Wallops Island, Virginia. The release took place at an altitude of approximately 260 km. The release produced a luminous cloud which expanded very rapidly, disappearing to the human eye in about 20 seconds. Barium ion concentration slowly increased over a wide area of sky until measurements were discontinued at sunrise (about 30 minutes).

Optical emission generated by collisions of 5 eV O(3P) atoms with surface-absorbed hydrazine

NASA Technical Reports Server (NTRS)

Orient, O. J.; Martus, K. E.; Chutjian, A.; Murad, E.

1992-01-01

Optical emission has been observed corresponding to vibrational bands in the NH (A 3Pi - X 3Sigma(-)) electronic transition during collisions of 5 eV, ground-state oxygen O(3P) atoms with MgF2 and Ni surfaces continuously exposed to a beam of hydrazine (N2H4). The NH emission intensity is observed to be about five times greater for MgF2 than for Ni. No dependence on temperature was observed for either surface in the range 240 - 340 K, implying that the NH-producing intermediate species is tightly bound. The half-lifetime for desorption of hydrazine from each surface was measured. This was found to be 120 min for the MgF2 surface at 240 K, and less than 20 min for Ni. After exposure, the surface composition was measured using X-ray photoelectron spectroscopy on the exposed and unexposed areas of both targets.

Material Compatibility with Space Storable Propellants. Design Guidebook

NASA Technical Reports Server (NTRS)

Uney, P. E.; Fester, D. A.

1972-01-01

An important consideration in the design of spacecraft for interplanetary missions is the compatibility of storage materials with the propellants. Serious problems can arise because many propellants are either extremely reactive or subject to catalytic decomposition, making the selection of proper materials of construction for propellant containment and control a critical requirement for the long-life applications. To aid in selecting materials and designing and evaluating various propulsion subsystems, available information on the compatibility of spacecraft materials with propellants of interest was compiled from literature searches and personal contacts. The compatibility of both metals and nonmetals with hydrazine, monomethyl hydrazine, nitrated hydrazine, and diborance fuels and nitrogen tetroxide, fluorine, oxygen difluoride, and Flox oxidizers was surveyed. These fuels and oxidizers encompass the wide variety of problems encountered in propellant storage. As such, they present worst case situations of the propellant affecting the material and the material affecting the propellant. This includes material attack, propellant decomposition, and the formation of clogging materials.

Confidence Testing of Shell 405 and S-405 Catalysts in a Monopropellant Hydrazine Thruster

NASA Technical Reports Server (NTRS)

McRight, Patrick; Popp, Chris; Pierce, Charles; Turpin, Alicia; Urbanchock, Walter; Wilson, Mike

2005-01-01

As part of the transfer of catalyst manufacturing technology from Shell Chemical Company (Shell 405 catalyst manufactured in Houston, Texas) to Aerojet (S-405 manufactured in Redmond, Washington), Aerojet demonstrated the equivalence of S-405 and Shell 405 at beginning of life. Some US aerospace users expressed a desire to conduct a preliminary confidence test to assess end-of-life characteristics for S-405. NASA Marshall Space Flight Center (MSFC) and Aerojet entered a contractual agreement in 2004 to conduct a confidence test using a pair of 0.2-lbf MR-103G monopropellant hydrazine thrusters, comparing S-405 and Shell 405 side by side. This paper summarizes the formulation of this test program, explains the test matrix, describes the progress of the test, and analyzes the test results. This paper also includes a discussion of the limitations of this test and the ramifications of the test results for assessing the need for future qualification testing in particular hydrazine thruster applications.

Monolithic catalyst beds for hydrazine reactors

NASA Technical Reports Server (NTRS)

1973-01-01

A monolithic catalyst bed for monopropellant hydrazine decomposition was evaluated. The program involved the evaluation of a new hydrazine catalyst concept wherein open-celled foamed materials are used as supports for the active catalysts. A high-surface-area material is deposited upon the open-celled foamed material and is then coated with an active metal to provide a spontaneous catalyst. Only a fraction of the amount of expensive active metal in currently available catalysts is needed to promote monolithic catalyst. Numerous parameters were evaluated during the program, and the importance of additional parameters became obvious only while the program was in progress. A demonstration firing (using a 2.2-Newton (N)(0.5-lbf) reactor) successfully accumulated 7,700 seconds of firing time and 16 ambient temperature starts without degradation. Based on the excellent results obtained throughout the program and the demonstrated life capability of the monolithic foam, it is recommended that additional studies be conducted to further exploit the advantages of this concept.

Synthesis, properties, and NMR studies of a C8-phenylguanine modified oligonucleotide that preferentially adopts the Z DNA conformation.

PubMed

Gannett, Peter M; Heavner, Sue; Daft, Jonathan R; Shaughnessy, Kevin H; Epperson, Jon D; Greenbaum, Nancy L

2003-10-01

Carcinogenic aryl hydrazines produce C8-arylated purine adducts. The effect of these adducts on DNA conformation and their role in hydrazine carcinogenesis are unknown. Here, we describe a new synthetic route to produce these adducts that is also compatible with the synthesis of the corresponding phosphoramidites needed for oligonucleotide synthesis. Two oligonucleotides were prepared, an unmodified oligonucleotide, d((5)(')CGCGCGCGCG(3)(')), and a C8-phenylguanine modified oligonucleotide, d((5)(')CGCGCGCGCG(3)(')) (G = 8-phenylguanine). These oligonucleotides were compared using thermal denaturation, circular dichroism, NMR, and molecular modeling. The phenyl modification destabilizes the B DNA form and stabilizes the Z DNA form such that the B:Z ratio is near one under physiological conditions. In light of recent studies that show a role for Z DNA in gene expression and cell transformation, Z DNA stabilization by C8-arylguanine formation from aryl hydrazines may be relevant to their role in carcinogenesis.

Automated solid-phase extraction coupled online with HPLC-FLD for the quantification of zearalenone in edible oil.

PubMed

Drzymala, Sarah S; Weiz, Stefan; Heinze, Julia; Marten, Silvia; Prinz, Carsten; Zimathies, Annett; Garbe, Leif-Alexander; Koch, Matthias

2015-05-01

Established maximum levels for the mycotoxin zearalenone (ZEN) in edible oil require monitoring by reliable analytical methods. Therefore, an automated SPE-HPLC online system based on dynamic covalent hydrazine chemistry has been developed. The SPE step comprises a reversible hydrazone formation by ZEN and a hydrazine moiety covalently attached to a solid phase. Seven hydrazine materials with different properties regarding the resin backbone, pore size, particle size, specific surface area, and loading have been evaluated. As a result, a hydrazine-functionalized silica gel was chosen. The final automated online method was validated and applied to the analysis of three maize germ oil samples including a provisionally certified reference material. Important performance criteria for the recovery (70-120 %) and precision (RSDr <25 %) as set by the Commission Regulation EC 401/2006 were fulfilled: The mean recovery was 78 % and RSDr did not exceed 8 %. The results of the SPE-HPLC online method were further compared to results obtained by liquid-liquid extraction with stable isotope dilution analysis LC-MS/MS and found to be in good agreement. The developed SPE-HPLC online system with fluorescence detection allows a reliable, accurate, and sensitive quantification (limit of quantification, 30 μg/kg) of ZEN in edible oils while significantly reducing the workload. To our knowledge, this is the first report on an automated SPE-HPLC method based on a covalent SPE approach.

Microbial Hydrocarbon Co-oxidation

PubMed Central

Raymond, R. L.; Jamison, V. W.; Hudson, J. O.

1967-01-01

Nocardia cultures, isolated from soil by use of n-paraffins as the sole carbon source, have been shown to bring about significant oxidation of several methyl-substituted mono- and dicyclic aromatic hydrocarbons. Oxygen uptake by washed cell suspensions was not a reliable indicator of oxidation. Under co-oxidation conditions in shaken flasks, o- and p-xylenes were oxidized to their respective mono-aromatic acids, o-toluic and p-toluic acids. In addition, a new fermentation product, 2, 3-dihydroxy-p-toluic acid, was found in the p-xylene oxidation system. Of 10 methyl-substituted naphthalenes tested (1-methyl, 2-methyl, 1, 3-dimethyl, 1, 4-dimethyl, 1, 5-dimethyl, 1, 8-dimethyl, 1, 6-dimethyl, 2, 3-dimethyl, 2, 6-dimethyl, 2, 7-dimethyl), only those containing a methyl group in the β position were oxidized at this position to the mono acid. PMID:6049305

Photochemical synthesis of biomolecules under anoxic conditions

NASA Technical Reports Server (NTRS)

Folsome, C.; Brittain, A.; Zelko, M.

1983-01-01

The long-wavelength UV anoxic photosynthesis of uracil, various sugars (including deoxyribose and glycoaldehyde), amino acids, and other organic photoproducts is reported. The reactions were conducted in a mixture of water, calcium carbonate, hydrazine, and formaldehyde which were subjected to 24 hr or 72 hr radiation. Product yields were greatest when the hydrazine/formaldehyde ratio was one, and when the reactant concentrations were low. These data suggest that organic products can be formed in variety from those amounts of formaldehyde and hydazine precursors which are themselves formed under anoxic UV photochemical conditions.

Hydrazine Blending and Storage Facility Wastewater Treatment and Decommissioning Assessment. Version 3.1

DTIC Science & Technology

1988-06-01

Valve Pit Number 2 Location One near hydrazine/aerozine tank area .nd one near wastewater tank area *There is a variety of underground piping at the...loading station (wipe of drum filling nozzles/connectors) 3,475 19.u I W-1U Tank HAS-?, drain value (Tank pit valve ) <S ɘ.2 W-110 Tank HAS-I, control... valve (on top) sample bottle broken W-111 Tank Truck Station, Truck loading filler nozzle and boom sample bottle broken I/ UUMH - 1,1

Application of selection techniques to electric-propulsion options on an advanced synchronous satellite

NASA Technical Reports Server (NTRS)

Holcomb, L. B.; Degrey, S. P.

1973-01-01

This paper addresses the comparison of several candidate auxiliary-propulsion systems and system combinations for an advanced synchronous satellite. Economic selection techniques, evolved at the Jet Propulsion Laboratory, are used as a basis for system option comparisons. Electric auxiliary-propulsion types considered include pulsed plasma and ion bombardment, with hydrazine systems used as a state-of-the-art reference. Current as well as projected electric-propulsion system performance data are used, as well as projected hydrazine system costs resulting from NASA standardization program projections.

Design and Implementation of the MSL Cruise Propulsion Tank Heaters

NASA Technical Reports Server (NTRS)

Krylo, Robert; Mikhaylov, Rebecca; Cucullu, Gordon; Watkins, Brenda

2008-01-01

This slide presentation reviews the design and the implementation of the heaters for the Mars Science Laboratory (MSL). The pressurized tanks store hydrazine that freezes at 2 C, this means that heaters are required to keep the hydrazine and the helium at 36 C for the trip to Mars. Using the TMG software the heat loss was analyzed, and a thermal model simulates a half full tank which yielded a 13W heating requirement for each hemisphere. Views of the design, and the heater are included.

Environmental Quality Research: Fish and Aufwuchs Bioassay

DTIC Science & Technology

1977-11-01

WSF) of JP-8 and the solution was renewed each day. Acute toxicity as assessed by the 96-hr LC 50 values was not significantly different over the pH...The 96-hr LC 50 of hydrazine to three-spine sticklebacks was 3.4 mg/i (nominal initial concentration) using 24 hr solution renewal, but the estimated...34spill," i.e., static bioassay with no hydrazine renewal, the 96-hr LC 50 to sticklebacks was 6.6 mg/k (95% confidence limits of 5.0 to 8.8 mg/k) based

Development of a potentiometric EDTA method for determination of molybdenum. Use of the analysis for molybdenite concentrates

NASA Technical Reports Server (NTRS)

Khristova, R.; Vanmen, M.

1986-01-01

Based on considerations of principles and experimental data, the interference of sulfate ions in poteniometric titration of EDTA with FeCl3 was confirmed. The method of back complexometric titration of molybdenum of Nonova and Gasheva was improved by replacing hydrazine sulfate with hydrazine hydrochloride for reduction of Mo(VI) to Mo(V). The method can be used for one to tenths of mg of molybdenum with 0.04 mg standard deviation. The specific method of determination of molybdenum in molybdenite concentrates is presented.

A study for hypergolic vapor sensor development

NASA Technical Reports Server (NTRS)

Stetter, J. R.

1977-01-01

The use of an electrochemical technique for MMH and N02 measurement was investigated. Specific MMH and N02 electrochemical sensors were developed. Experimental techniques for preparation, handling, and analysis of hydrazine's vapor mixtures at ppb and ppm levels were developed. Two approaches to N02 instrument design were evaluated including specific adsorption and specific electrochemical reduction. Two approaches to hydrazines monitoring were evaluated including catalytic conversion to N0 with subsequent N0 detection and direct specific electrochemical oxidation. Two engineering prototype MMH/N02 monitors were designed and constructed.

Low level vapor verification of monomethyl hydrazine

NASA Technical Reports Server (NTRS)

Mehta, Narinder

1990-01-01

The vapor scrubbing system and the coulometric test procedure for the low level vapor verification of monomethyl hydrazine (MMH) are evaluated. Experimental data on precision, efficiency of the scrubbing liquid, instrument response, detection and reliable quantitation limits, stability of the vapor scrubbed solution, and interference were obtained to assess the applicability of the method for the low ppb level detection of the analyte vapor in air. The results indicated that the analyte vapor scrubbing system and the coulometric test procedure can be utilized for the quantitative detection of low ppb level vapor of MMH in air.

Detection of rare species of volatile organic selenium metabolites in male golden hamster urine.

PubMed

Kwak, Jae; Ohrnberger, Sarah A; Valencak, Teresa G

2016-07-01

Selenium has been considered as an essential trace element in mammals and its intake comes mainly from food. Mammals can metabolize both inorganic and organic species, and urinary excretion is the primary elimination route of selenium. Selenosugars and trimethylselenonium ion have been identified as major urinary metabolites. Other metabolites have been reported, but they were detected in some studies and not in others. Still, a large portion of the ingested selenium eliminated from the body is unknown. Volatile selenium species may account for a certain portion of the unknown species since they can easily be lost during sample analyses. While we analyzed male golden hamster urine in search of potential volatile pheromone(s), four volatile selenium compounds were detected. They were dimethyl selenenylsulfide, dimethyl diselenide, dimethyl bis(thio)selenide, and dimethyl selenodisulfide. When the urine samples were aged and dried for 48 h, dimethyl selenodisulfide tended to increase, while others decreased. The increase might be due to the formation of dimethyl selenodisulfide via reaction of dimethyl diselenide and dimethyl trisulfide whose concentration increased as urine aged. To our knowledge, dimethyl bis(thio)selenide and dimethyl selenodisulfide have never been demonstrated in urine. It remains to be determined whether these species are common metabolites in other animals or hamster-specific.

Hydrazine solution processed Sb2S3, Sb2Se3 and Sb2(S1−xSex)3 film: molecular precursor identification, film fabrication and band gap tuning

PubMed Central

Yang, Bo; Xue, Ding-Jiang; Leng, Meiying; Zhong, Jie; Wang, Liang; Song, Huaibing; Zhou, Ying; Tang, Jiang

2015-01-01

Sb2(S1−xSex)3 (0 ≤ x ≤ 1) compounds have been proposed as promising light-absorbing materials for photovoltaic device applications. However, no systematic study on the synthesis and characterization of polycrystalline Sb2(S1−xSex)3 thin films has been reported. Here, using a hydrazine based solution process, single-phase Sb2(S1−xSex)3 films were successfully obtained. Through Raman spectroscopy, we have investigated the dissolution mechanism of Sb in hydrazine: 1) the reaction between Sb and S/Se yields [Sb4S7]2-/[Sb4Se7]2- ions within their respective solutions; 2) in the Sb-S-Se precursor solutions, Sb, S, and Se were mixed on a molecular level, facilitating the formation of highly uniform polycrystalline Sb2(S1−xSex)3 thin films at a relatively low temperature. UV-vis-NIR transmission spectroscopy revealed that the band gap of Sb2(S1−xSex)3 alloy films had a quadratical relationship with the Se concentration x and it followed the equation , where the bowing parameter was 0.118 eV. Our study provides a valuable guidance for the adjustment and optimization of the band gap in hydrazine solution processed Sb2(S1−xSex)3 alloy films for the future fabrication of improved photovoltaic devices. PMID:26042519

Characterization of Anammox Hydrazine Dehydrogenase, a Key N2-producing Enzyme in the Global Nitrogen Cycle*

PubMed Central

Maalcke, Wouter J.; Reimann, Joachim; de Vries, Simon; Butt, Julea N.; Dietl, Andreas; Kip, Nardy; Mersdorf, Ulrike; Barends, Thomas R. M.; Jetten, Mike S. M.; Keltjens, Jan T.; Kartal, Boran

2016-01-01

Anaerobic ammonium-oxidizing (anammox) bacteria derive their energy for growth from the oxidation of ammonium with nitrite as the electron acceptor. N2, the end product of this metabolism, is produced from the oxidation of the intermediate, hydrazine (N2H4). Previously, we identified N2-producing hydrazine dehydrogenase (KsHDH) from the anammox organism Kuenenia stuttgartiensis as the gene product of kustc0694 and determined some of its catalytic properties. In the genome of K. stuttgartiensis, kustc0694 is one of 10 paralogs related to octaheme hydroxylamine (NH2OH) oxidoreductase (HAO). Here, we characterized KsHDH as a covalently cross-linked homotrimeric octaheme protein as found for HAO and HAO-related hydroxylamine-oxidizing enzyme kustc1061 from K. stuttgartiensis. Interestingly, the HDH trimers formed octamers in solution, each octamer harboring an amazing 192 c-type heme moieties. Whereas HAO and kustc1061 are capable of hydrazine oxidation as well, KsHDH was highly specific for this activity. To understand this specificity, we performed detailed amino acid sequence analyses and investigated the catalytic and spectroscopic (electronic absorbance, EPR) properties of KsHDH in comparison with the well defined HAO and kustc1061. We conclude that HDH specificity is most likely derived from structural changes around the catalytic heme 4 (P460) and of the electron-wiring circuit comprising seven His/His-ligated c-type hemes in each subunit. These nuances make HDH a globally prominent N2-producing enzyme, next to nitrous oxide (N2O) reductase from denitrifying microorganisms. PMID:27317665

Green Propellant Demonstration with Hydrazine Catalyst of F-16 Emergency Power Unit

NASA Technical Reports Server (NTRS)

Robinson, Joel W.; Brechbill, Shawn

2015-01-01

Some space vehicle and aircraft Auxiliary Power Units (APUs) use hydrazine propellant for generating power. Hydrazine is a toxic, hazardous fuel which requires special safety equipment and processes for handling and loading. In recent years, there has been development of two green propellants that could enable their use in APU's: the Swedish LMP-103S and the Air Force Research Laboratory (AFRL) AF-M315E. While there has been work on development of these propellants for thruster applications (Prisma and Green Propulsion Infusion Mission, respectively), there has been less focus on the application to power units. Beginning in 2012, an effort was started by the Marshall Space Flight Center (MSFC) on the APU application. The MSFC plan was to demonstrate green propellants with residual Space Shuttle hardware. The principal investigator was able to acquire a Solid Rocket Booster gas generator and an Orbiter APU. Since these test assets were limited in number, an Air Force equivalent asset was identified: the F-16 Emergency Power Unit (EPU). In June 2013, two EPU's were acquired from retired aircraft located at Davis Monthan Air Force Base. A gas generator from one of these EPU's was taken out of an assembly and configured for testing with a version of the USAF propellant with a higher water content (AF-M315EM) to reduce decomposition temperatures. Testing in November 2014 has shown that this green propellant is reactive with the Hydrazine catalyst (Shell 405) generating 300 psi of pressure with the existing F-16 EPU configuration. This paper will highlight the results of MSFC testing in collaboration with AFRL.

Benefits of Low-Power Electrothermal Propulsion

NASA Technical Reports Server (NTRS)

Oleson, Steven R.; Sankovic, John M.

1997-01-01

Mission analyses were completed to show the benefits of low-power electrothermal propulsion systems for three classes'of LEO smallsat missions. Three different electrothermal systems were considered: (1) a 40 W ammonia resistojet system, (2) a 600 W hydrazine arcjet system, and (3) a 300 W ammonia resistojet. The benefits of using two 40 W ammonia resistojet systems were analyzed for three months of drag makeup of a Shuttle-launched 100 kg spacecraft in a 297 km orbit. The two 46 W resistojets decreased the propulsion system wet mass by 50% when compared to state-of-art hydrazine monopropellant thrusters. The 600 W arcjet system was used for a 300 km sun synchronous makeup mission of a 1000 kg satellite and was found to decrease the wet propulsion mass by 30%. Finally, the 300 W arcjet system was used on a 200 kg Earth-orbiting spacecraft for both orbit transfer from 300 to 400 km, two years of drag makeup, and a final orbit rise to 700 km. The arcjet system was determined to halve the propulsion system wet mass required for that scenario as compared to hydrazine monopropellant thrusters.

Heterobimetallic Ti/Co Complexes That Promote Catalytic N-N Bond Cleavage.

PubMed

Wu, Bing; Gramigna, Kathryn M; Bezpalko, Mark W; Foxman, Bruce M; Thomas, Christine M

2015-11-16

Treatment of the tris(phosphinoamide) titanium precursor ClTi(XylNP(i)Pr2)3 (1) with CoI2 leads to the heterobimetallic complex (η(2)-(i)Pr2PNXyl)Ti(XylNP(i)Pr2)2(μ-Cl)CoI (2). One-electron reduction of 2 affords (η(2)-(i)Pr2PNXyl)Ti(XylNP(i)Pr2)2CoI (3), which can be reduced by another electron under dinitrogen to generate the reduced diamagnetic complex (THF)Ti(XylNP(i)Pr2)3CoN2 (4). The removal of the dinitrogen ligand from 4 under vacuum affords (THF)Ti(XylNP(i)Pr2)3Co (5), which features a Ti-Co triple bond. Treatment of 4 with hydrazine or methyl hydrazine results in N-N bond cleavage and affords the new diamagnetic complexes (L)Ti(XylNP(i)Pr2)3CoN2 (L = NH3 (6), MeNH2 (7)). Complexes 4, 5, and 6 have been shown to catalyze the disproportionation of hydrazine into ammonia and dinitrogen gas through a mechanism involving a diazene intermediate.

N(4)-Methyl-N(4)-(2-methylphenyl)-1H-pyrazolo[3,4-d]pyrimidine-4,6-diamine-ethanol-hydrazine (1/0.865/0.135): hydrogen-bonded ribbons containing four independent ring types.

PubMed

Trilleras, Jorge; Quiroga, Jairo; Cobo, Justo; Glidewell, Christopher

2009-06-01

N(4)-Methyl-N(4)-(2-methylphenyl)-1H-pyrazolo[3,4-d]pyrimidine-4,6-diamine crystallizes from ethanol as a mixed solvate, C(13)H(14)N(6).0.865C(2)H(6)O.0.135N(2)H(4), (I), where the hydrazine has been carried through from the initial preparation. Within the heterocyclic component, the 2-methylphenyl substituent is disordered over two sets of sites. There is an intramolecular C-H...pi(arene) hydrogen bond, which may control the molecular conformation of the heterocycle. The heterocyclic molecules are linked by two independent N-H...N hydrogen bonds in a chain containing two types of R(2)(2)(8) ring. The ethanol component is linked to this chain by a combination of O-H...N and N-H...O hydrogen bonds and the hydrazine component by two N-H...N hydrogen bonds, so generating two R(3)(3)(9) rings and thus forming a ribbon containing four distinct ring types.

Preparation and characterization of AuNPs/CNTs-ErGO electrochemical sensors for highly sensitive detection of hydrazine.

PubMed

Zhao, Zhenting; Sun, Yongjiao; Li, Pengwei; Zhang, Wendong; Lian, Kun; Hu, Jie; Chen, Yong

2016-09-01

A highly sensitive electrochemical sensor of hydrazine has been fabricated by Au nanoparticles (AuNPs) coating of carbon nanotubes-electrochemical reduced graphene oxide composite film (CNTs-ErGO) on glassy carbon electrode (GCE). Cyclic voltammetry and potential amperometry have been used to investigate the electrochemical properties of the fabricated sensors for hydrazine detection. The performances of the sensors were optimized by varying the CNTs to ErGO ratio and the quantity of Au nanoparticles. The results show that under optimal conditions, a sensitivity of 9.73μAμM(-1)cm(-2), a short response time of 3s, and a low detection limit of 0.065μM could be achieved with a linear concentration response range from 0.3μM to 319μM. The enhanced electrochemical performances could be attributed to the synergistic effect between AuNPs and CNTs-ErGO film and the outstanding catalytic effect of the Au nanoparticles. Finally, the sensor was successfully used to analyse the tap water, showing high potential for practical applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Multifunctional Co₀.₈₅Se/graphene hybrid nanosheets: controlled synthesis and enhanced performances for the oxygen reduction reaction and decomposition of hydrazine hydrate.

PubMed

Zhang, Lin-fei; Zhang, Chun-yang

2014-01-01

Ultrathin nanosheets possess novel electronic structures and physical properties as compared with their corresponding bulk samples. However, the controlled synthesis of ultrathin monolayer nanosheets still remains a great challenge due to the lack of an intrinsic driving force for anisotropic growth of two-dimensional (2D) structures. Here we demonstrate, for the first time to our knowledge, the in situ synthesis of large-scale ultrathin single-crystalline Co₀.₈₅Se nanosheets on graphene oxide (GO) sheets, with a thickness of 3 nm. Owing to the synergetic chemical coupling effects between GO and Co₀.₈₅Se, the Co₀.₈₅Se/graphene hybrid nanosheets exhibit the highest catalytic performance among the available cobalt chalcogenide-based catalysts for the oxygen reduction reaction (ORR). Moreover, Co₀.₈₅Se/graphene hybrid nanosheets can catalyze the decomposition of hydrazine hydrate rapidly, with 97% of hydrazine hydrate being degraded in 12 min and the degradation rate remaining constant over 10 consecutive cycles, thus having great potential as long-term catalysts in wastewater treatment.

In-situ analysis of hydrazine decomposition products

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Whalen, Margaret V.

1987-01-01

A gas analyzer utilizing a nondispersive infrared (NDIR) detection system was used to monitor the ammonia and water vapor content of the products of a previously unused hydrazine gas generator. This provided an in-situ measurement of the generator's efficiency difficult to obtain by other means. The analyzer was easily installed in both the calibration and hydrazine systems, required no maintenance other than periodic zero adjustments, and performed well for extended periods in the operating range tested. The catalyst bed operated smoothly and repeatably during the 28 hr of testing. No major transients were observed on startup or during steady state operation. The amount of ammonia in the output stream of the gas generator was found to be a strong function of temperature at catalyst bed temperatures below 450 C. At temperatures above this, the efficiency remained nearly constant. On startup the gas generator efficiency was found to decrease with time until a steady state value was attained. Elevated catalyst bed temperatures in the periods before steady state operation was found to be responsible for this phenomenon.

A design study of hydrazine and biowaste resistojets

NASA Technical Reports Server (NTRS)

Page, R. J.; Stoner, W. A.; Barker, L.

1986-01-01

A generalized modeling program was adapted in BASIC on a personal computer to compare the performance of four types of biowaste resistojets and two types of hydrazine augmenters. Analyzed biowaste design types were: (1) an electrically conductive ceramic heater-exchanger of zirconia; (2) a truss heater of platinum in cross flow; (3) an immersed bicoiled tubular heater-exchanger; and (4) a nonexposed, refractory metal, radiant heater in a central cavity within a heat exchanger case. Concepts 2 and 3 are designed to have an efficient, stainless steel outer pressure case. The hydrazine design types are: (5) an immersed bicoil heater exchanger and (6) a nonexposed radiant heater now with a refractory metal case. The ceramic biowaste resistojet has the highest specific impulse growth potential at 2000 K of 192.5 (CO2) and 269 s (H2O). The bicoil produces the highest augmenter temperature of 1994 K for a 2073 K heater giving 317 s at .73 overall efficiency. Detailed temperature profiles of each of the designs are shown. The scaled layout drawings of each are presented with recommended materials and fabrication methods.

New hydrazine and hydrazide quinoxaline 1,4-di-N-oxide derivatives: In silico ADMET, antiplasmodial and antileishmanial activity.

PubMed

Quiliano, Miguel; Pabón, Adriana; Ramirez-Calderon, Gustavo; Barea, Carlos; Deharo, Eric; Galiano, Silvia; Aldana, Ignacio

2017-04-15

We report the design (in silico ADMET criteria), synthesis, cytotoxicity studies (HepG-2 cells), and biological evaluation of 15 hydrazine/hydrazide quinoxaline 1,4-di-N-oxide derivatives against the 3D7 chloroquine sensitive strain and FCR-3 multidrug resistant strain of Plasmodium falciparum and Leishmania infantum (axenic amastigotes). Fourteen of derivatives are novel quinoxaline 1,4-di-N-oxide derivatives. Compounds 18 (3D7 IC 50 =1.40μM, FCR-3 IC 50 =2.56μM) and 19 (3D7 IC 50 =0.24μM, FCR-3 IC 50 =2.8μM) were identified as the most active against P. falciparum, and they were the least cytotoxic (CC 50 -values>241μM) and most selective (SI>86). None of the compounds tested against L. infantum were considered to be active. Additionally, the functional role of the hydrazine and hydrazide structures were studied in the quinoxaline 1,4-di-N-oxide system. Copyright © 2017 Elsevier Ltd. All rights reserved.

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10127 - Alkenyl dimethyl betaine (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkenyl dimethyl betaine (generic... Specific Chemical Substances § 721.10127 Alkenyl dimethyl betaine (generic). (a) Chemical substance and... dimethyl betaine (PMN P-06-693) is subject to reporting under this section for the significant new uses...

40 CFR 721.10666 - Quaternary ammonium compounds, bis(fattyalkyl) dimethyl, salts with tannins (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

...(fattyalkyl) dimethyl, salts with tannins (generic). 721.10666 Section 721.10666 Protection of Environment..., bis(fattyalkyl) dimethyl, salts with tannins (generic). (a) Chemical substance and significant new... compounds, bis(fattyalkyl) dimethyl, salts with tannins (PMN P-12-437) is subject to reporting under this...

40 CFR 721.10666 - Quaternary ammonium compounds, bis(fattyalkyl) dimethyl, salts with tannins (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

...(fattyalkyl) dimethyl, salts with tannins (generic). 721.10666 Section 721.10666 Protection of Environment..., bis(fattyalkyl) dimethyl, salts with tannins (generic). (a) Chemical substance and significant new... compounds, bis(fattyalkyl) dimethyl, salts with tannins (PMN P-12-437) is subject to reporting under this...

40 CFR 721.10352 - Dimethyl terephthalate, polymer with alkyl diol and substituted benzoates (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Dimethyl terephthalate, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10352 Dimethyl terephthalate, polymer... subject to reporting. (1) The chemical substance identified generically as dimethyl terephthalate, polymer...

40 CFR 721.10352 - Dimethyl terephthalate, polymer with alkyl diol and substituted benzoates (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Dimethyl terephthalate, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10352 Dimethyl terephthalate, polymer... subject to reporting. (1) The chemical substance identified generically as dimethyl terephthalate, polymer...

40 CFR 721.10352 - Dimethyl terephthalate, polymer with alkyl diol and substituted benzoates (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Dimethyl terephthalate, polymer with... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10352 Dimethyl terephthalate, polymer... subject to reporting. (1) The chemical substance identified generically as dimethyl terephthalate, polymer...

40 CFR 721.6167 - Piperdinium, 1,1-dimethyl-, chloride.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Piperdinium, 1,1-dimethyl-, chloride... Substances § 721.6167 Piperdinium, 1,1-dimethyl-, chloride. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as piperdinium, 1,1-dimethyl-, chloride. (PMN...

21 CFR 172.824 - Sodium mono- and dimethyl naphthalene sulfonates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium mono- and dimethyl naphthalene sulfonates... sulfonates. The food additive sodium mono- and dimethyl naphthalene sulfonates may be safely used in... statement declaring the presence of sodium mono- and dimethyl naphthalene sulfonates. [42 FR 14491, Mar. 15...

Synthesis and evaluation of borates derived from boric acid and diols for the protection of wood against fungal decay and thermal degradation

Treesearch

George C. Chen

2004-01-01

N,N-dimethyl amino carbinol catechol borate(1). N,N-dimethyl amino carbinol-4-methyl catechol borate(2), N,N-dimethyl amino carbinol-4-t- butyl catechol borate(3). N,N-dimethyl amino carbinol-2,3-naphthyl borate 4) were synthesized by refluxing boric acid and diol in DMF(N,N-dimethyl formamide). The borates were characterized by NMR. Wood impregnated with borate 1,2 or...

The vibrational spectra and structures of dimethyl oxaloacetate and dimethyl oxaloacetate- d2

NASA Astrophysics Data System (ADS)

Schiering, David W.; Katon, J. E.

The complete vibrational spectra of dimethyl oxaloacetate and dimethyl oxaloacetate- d2 have been recorded and analyzed. The i.r. spectra were recorded at liquid N 2 as well as ambient temperature. Tentative vibrational assignments are proposed based on an enol structure in the crystalline phase. In solution, dimethyl oxaloacetate exists as a tautomeric mixture of keto and enol forms. Evidence for the existence of different enol conformers in CCl 4 and CS 2 solutions is also presented.

Theoretical performance of some rocket propellants containing hydrogen, nitrogen, and oxygen

NASA Technical Reports Server (NTRS)

Miller, Riley O; Ordin, Paul M

1948-01-01

Theoretical performance data including nozzle-exit temperature, specific impulse, volume specific impulse and composition, temperature, and mean molecular weight of reaction products based on frozen equilibrium and isentropic expansion are presented for 13 propellant combinations at reaction pressure of 300 pounds per square inch absolute and expansion ratio of 20.4. On basis of maximum specific impulse alone, five fuels had the following order for any given oxidant: liquid hydrogen, hydrazine, liquid ammonia, and either hydrazine hydrate or hydroxylamine. Three oxidants with a given fuel had the following order: liquid ozone, liquid oxygen, and 100-percent hydrogen peroxide.

Electric auxiliary power unit for Shuttle evolution

NASA Technical Reports Server (NTRS)

Meyer, Doug; Weber, Kent; Scott, Walter

1989-01-01

The Space Shuttle Orbiter currently uses three hydrazine fueled auxiliary power units (APUs) to provide hydraulic power for the vehicle aerodynamic surface controls, main engine thrust vector control, landing gear, steering, and brakes. Electric auxiliary power units have been proposed as possible replacements to the hydrazine auxiliary power units. Along with the potential advantages, this paper describes an Electric APU configuration and addresses the technical issues and risks associated with the subsystem components. Additionally, characteristics of an Electric APU compared to the existing APU and the direction of future study with respect to the Electric APU is suggested.

Microwave-Assisted Piloty-Robinson Synthesis of 3,4-Disubstituted Pyrroles

PubMed Central

Milgram, Benjamin C.; Eskildsen, Katrine; Richter, Steven M.; Scheidt, W. Robert; Scheidt, Karl A.

2007-01-01

The synthesis of N-acyl 3,4-disubstituted pyrroles can be accomplished directly from hydrazine and an aldehyde via a Piloty-Robinson pyrrole synthesis. The use of microwave radiation for the cyclization and pyrrole formation greatly reduces the time necessary for this process and facilitates moderate to good yields from hydrazine for the corresponding 3,4-disubstituted products (5–12). By simple hydrolysis, the free N–H pyrroles can be accessed after the Piloty-Robinson reaction and then used directly in the synthesis of octaethylporphyrin (H2OEP, 14) and octaethyltetraphenylporphyrin (H2OETPP, 15). PMID:17432915

SEPARATION OF URANIUM FROM OTHER METALS

DOEpatents

Hyman, H.H.

1959-07-01

The separation of uranium from other elements, such as ruthenium, zirconium, niobium, cerium, and other rare earth metals is described. According to the invention, this is accomplished by adding hydrazine to an acid aqueous solution containing salts of uranium, preferably hexavalent uranium, and then treating the mixture with a substantially water immiscible ketone, such as hexone. A reaction takes place between the ketone and the hydrazine whereby a complex, a ketazine, is formed; this complex has a greater power of extraction for uranium than the ketone by itself. When contaminating elements are present, they substantially remain in ihe aqueous solution.

α-Oxo-Ketenimines from Isocyanides and α-Haloketones: Synthesis and Divergent Reactivity.

PubMed

Mamboury, Mathias; Wang, Qian; Zhu, Jieping

2017-09-18

The palladium-catalyzed reaction of α-haloketones with isocyanides afforded α-oxo-ketenimines through β-hydride elimination of the β-oxo-imidoyl palladium intermediates. Reaction of these relatively stable α-oxo-ketenimines with nucleophiles such as hydrazines, hydrazoic acid, amines, and Grignard reagent afforded pyrazoles, tetrazole, β-keto amidines, and enaminone, respectively, with high chemoselectivity. Whereas amines attack exclusively on the ketenimine functions, the formal [3+2] cycloaddition between N-monosubstituted hydrazines and α-oxo-ketenimines was initiated by nucleophilic addition to the carbonyl group. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

NASA - Johnson Space Center's New Capabilities for Air Purification

NASA Technical Reports Server (NTRS)

Graf, John

2015-01-01

NASA has some unique and challenging air purification problems that cannot be adequately met with COTS technology: 1) ammonia removal from air, 2) hydrazine removal from air, 3) CO conversion to CO2 in low temperature, high humidity environments. NASA has sponsored the development of new sorbents and new catalysts. These new sorbents and catalysts work better than COTS technology for our application. If attendees have a need for an effective ammonia sorbent, an effective hydrazine sorbent, or an effective CO conversion catalyst, we should learn to see if NASA sponsored technology development can help.

A Cooling System for the EAPU Shuttle Upgrade

NASA Technical Reports Server (NTRS)

Tongue, Stephen; Guyette, Greg; Irbeck, Bradley

2001-01-01

The Shuttle orbiter currently uses hydrazine-powered APU's for powering its hydraulic system pumps. To enhance vehicle safety and reliability, NASA is pursuing an APU upgrade where the hydrazine powered turbine is replaced by an electric motor pump and battery power supply. This EAPU (Electric APU) upgrade presents several thermal control challenges most notably the new requirement for moderate temperature control of high-power electron ics at 132 of (55.6 C). This paper describes how the existing Water Spray Boiler (WSB), which currently cools the hydraulic fluid and APU lubrication oil, is being modified to provide EAPU thermal management.

Environmental crack-growth behavior of high strength pressure vessel alloys

NASA Technical Reports Server (NTRS)

Forman, R. G.

1975-01-01

Results of sustained-load environmental crack growth threshold tests performed on six spacecraft pressure vessel alloys are presented. The alloys were Inconel 718, 6Al-4V titanium, A-286 steel, AM-350 stainless steel, cryoformed AISI 301 stainless steel; and cryoformed AISI 304L steel. The test environments for the program were air, pressurized gases of hydrogen, oxygen, nitrogen, and carbon dioxide, and liquid environments of distilled water, sea water, nitrogen tetroxide, hydrazine, aerozine 50, monomethyl hydrazine, and hydrogen peroxide. Surface flaw type specimens were used with flaws located in both base metal and weld metal.

Update on Chemical Analysis of Recovered Hydrazine Family Fuels for Recycling

NASA Technical Reports Server (NTRS)

Davis, C. L.

1997-01-01

The National Aeronautics and Space Administration, Kennedy Space Center, has developed a program to re-use and/or recycle hypergolic propellants recovered from propellant systems. As part of this effort, new techniques were developed to analyze recovered propellants. At the 1996 PDCS, the paper 'Chemical Analysis of Recovered Hydrazine Family Fuels For Recycling' presented analytical techniques used in accordance with KSC specifications which define what recovered propellants are acceptable for recycling. This paper is a follow up to the 1996 paper. Lower detection limits and response linearity were examined for two gas chromatograph methods.

Performance of a capillary propellant management device with hydrazine

NASA Technical Reports Server (NTRS)

Tegart, J. R.

1979-01-01

The propellant management device that was successfully used in the Viking Orbiter spacecraft was selected for the main propulsion system of the Teleoperator Retrieval System (TRS). Due to differences in the missions and different propellants, the operation of this sheet metal vane device required reverification for the TRS application. An analytical investigation was performed considering the adverse acceleration environment and the high contract angle of the hydrazine propellant. Drop tower tests demonstrated that the device would provide propellant acquisition while the TRS was docked with Skylab, but its operation would have to be supplemented through propellant settling when free-flying.

Enthalpies of Formation of Hydrazine and Its Derivatives.

PubMed

Dorofeeva, Olga V; Ryzhova, Oxana N; Suchkova, Taisiya A

2017-07-20

Enthalpies of formation, Δ f H 298 ° , in both the gas and condensed phase, and enthalpies of sublimation or vaporization have been estimated for hydrazine, NH 2 NH 2 , and its 36 various derivatives using quantum chemical calculations. The composite G4 method has been used along with isodesmic reaction schemes to derive a set of self-consistent high-accuracy gas-phase enthalpies of formation. To estimate the enthalpies of sublimation and vaporization with reasonable accuracy (5-20 kJ/mol), the method of molecular electrostatic potential (MEP) has been used. The value of Δ f H 298 ° (NH 2 NH 2 ,g) = 97.0 ± 3.0 kJ/mol was determined from 75 isogyric reactions involving about 50 reference species; for most of these species, the accurate Δ f H 298 ° (g) values are available in Active Thermochemical Tables (ATcT). The calculated value is in excellent agreement with the reported results of the most accurate models based on coupled cluster theory (97.3 kJ/mol, the average of six calculations). Thus, the difference between the values predicted by high-level theoretical calculations and the experimental value of Δ f H 298 ° (NH 2 NH 2 ,g) = 95.55 ± 0.19 kJ/mol recommended in the ATcT and other comprehensive reference sources is sufficiently large and requires further investigation. Different hydrazine derivatives have been also considered in this work. For some of them, both the enthalpy of formation in the condensed phase and the enthalpy of sublimation or vaporization are available; for other compounds, experimental data for only one of these properties exist. Evidence of accuracy of experimental data for the first group of compounds was provided by the agreement with theoretical Δ f H 298 ° (g) value. The unknown property for the second group of compounds was predicted using the MEP model. This paper presents a systematic comparison of experimentally determined enthalpies of formation and enthalpies of sublimation or vaporization with the results of calculations. Because of relatively large uncertainty in the estimated enthalpies of sublimation, it was not always possible to evaluate the accuracy of the experimental values; however, this model allowed us to detect large errors in the experimental data, as in the case of 5,5'-hydrazinebistetrazole. The enthalpies of formation and enthalpies of sublimation or vaporization have been predicted for the first time for ten hydrazine derivatives with no experimental data. A recommended set of self-consistent experimental and calculated gas-phase enthalpies of formation of hydrazine derivatives can be used as reference Δ f H 298 ° (g) values to predict the enthalpies of formation of various hydrazines by means of isodesmic reactions.

Exercise reduces inflammation and cell proliferation in rat colon carcinogenesis.

PubMed

Demarzo, Marcelo Marcos Piva; Martins, Lisandra Vanessa; Fernandes, Cleverson Rodrigues; Herrero, Fábio Augusto; Perez, Sérgio Eduardo de Andrade; Turatti, Aline; Garcia, Sérgio Britto

2008-04-01

There is evidence that the risk of colon cancer is reduced by appropriate levels of physical exercise. Nevertheless, the mechanisms involved in this protective effect of exercise remain largely unknown. Inflammation is emerging as a unifying link between a range of environment exposures and neoplastic risk. The carcinogen dimethyl-hydrazine (DMH) induces an increase in epithelial cell proliferation and in the expression of the inflammation-related enzyme cyclooxigenase-2 (COX-2) in the colon of rats. Our aim was to verify whether these events could be attenuated by exercise. Four groups of eight Wistar rats were used in the experiment. The groups G1 and G3 were sedentary (controls), and the groups G2 and G4 were submitted to 8 wk of swimming training, 5 d.wk. The groups G3 and G4 were given subcutaneous injections of DMH immediately after the exercise protocols. Fifteen days after the neoplasic induction, the rats were sacrificed and the colon was processed for histological examination and immunohistochemistry staining of proliferating cell nuclear antigen (PCNA) and COX-2. We found a significant increase in the PCNA-labeling index in both DMH-treated groups of rats. However, this increase was significantly attenuated in the training group G4 (P < 0.01). Similar results were observed in relation to the COX-2 expression. From our findings, we conclude that exercise training exerts remarkable antiproliferative and antiinflammatory effects in the rat colonic mucosa, suggesting that this may be an important mechanism to explain how exercise protects against colonic cancer.

A precursor to the beta-pyranosides of 3-amino-3,6-dideoxy-D-mannose (mycosamine).

PubMed

Alais, J; David, S

1992-06-04

SN2-type reaction of 3-O-(1-imidazyl)sulfonyl-1,2:5,6-di-O-isopropylidene-alpha-D-gluco furanose with benzoate gave the 3-O-benzoyl-alpha-D-allo derivative 2, which was hydrolysed to give the 5,6-diol 3. Compound 3 was converted into the 6-deoxy-6-iodo derivative 4 which was reduced with tributylstannane, and then position 5 was protected by benzyloxymethylation, to give 3-O-benzoyl-5-O-benzyloxymethyl-6-deoxy-1,2-O-isopropylidene-alpha -D- allofuranose (6). Debenzoylation of 6 gave 7, (1-imidazyl)sulfonylation gave 8, and azide displacement gave 3-azido-5-O-benzyloxymethyl-3,6-dideoxy- 1,2-O-isopropylidene-alpha-D-glucofuranose (9, 85%). Acetolysis of 9 gave 1,2,4-tri-O-acetyl-3-azido-3,6-dideoxy-alpha,beta-D-glucopyranose (10 and 11). Selective hydrolysis of AcO-1 in the mixture of 10 and 11 with hydrazine acetate (----12), followed by conversion into the pyranosyl chloride 13, treatment with N,N-dimethylformamide dimethyl acetal in the presence of tetrabutylammonium bromide, and benzylation gave 3-azido-4-O-benzyl-3,6-dideoxy-1,2-O-(1-methoxyethylidene)-alpha-D -glucopyranose (15). Treatment of 15 with dry acetic acid gave 1,2-di-O-acetyl-3-azido-4-O-benzyl-3,6-dideoxy-beta-D-glucopyranose (16, 86% yield) that was an excellent glycosyl donor in the presence of trimethylsilyl triflate, allowing the synthesis of cyclohexyl 2-O-acetyl-3-azido-4-O-benzyl-3,6-dideoxy-beta-D-glucopyranoside (17, 90%).(ABSTRACT TRUNCATED AT 250 WORDS)

A pyrazolyl-based thiolato single-source precursor for the selective synthesis of isotropic copper-deficient copper(I) sulfide nanocrystals: synthesis, optical and photocatalytic activity

NASA Astrophysics Data System (ADS)

Mondal, Gopinath; Santra, Ananyakumari; Bera, Pradip; Acharjya, Moumita; Jana, Sumanta; Chattopadhyay, Dipankar; Mondal, Anup; Seok, Sang Il; Bera, Pulakesh

2016-10-01

Hexagonal copper-deficient copper(I) sulfide (Cu2- x S, x = 0.03, 0.2) nanocrystals (NCs) are synthesized from a newly prepared single-source precursor (SP), [Cu(bdpa)2][CuCl2], where bdpa is benzyl 3,5-dimethyl-pyrazole-1-carbodithioate. The SP is crystallized with space group Pī and possesses a distorted tetrahedron structure with a CuN2S2 chromophore where the central copper is in +1 oxidation state. Distortion in copper(I) structure and the low decomposition temperature of SP make it favorable for the low-temperature solvent-assisted selective growth of high-copper content sulfides. The nucleation and growth of Cu2- x S ( x = 0.03, 0.2) are effectively controlled by the SP and the solvent in the solvothermal decomposition process. During decomposition, fragment benzyl thiol (PhCH2SH) from SP effectively passivates the nucleus leading to spherical nanocrystals. Further, solvent plays an important role in the selective thermochemical transformation of CuI-complex to Cu2- x S ( x = 0.03, 0.2) NCs. The chelating binders (solvent) like ethylene diamine (EN) and ethylene glycol (EG) prefer to form spherical Cu1.97S nanoparticles (djurleite), whereas nonchelating hydrazine hydrate (HH) shows the tendency to furnish hexagonal platelets of copper-deficient Cu1.8S. The optical band gap values (2.25-2.50 eV) show quantum confinement effect in the structure. The synthesized NCs display excellent catalytic activity ( 87 %) toward photodegradation of organic dyes like Congo Red (CR) and Methylene Blue (MB).

Effects of Lactobacillus salivarius Ren on cancer prevention and intestinal microbiota in 1, 2-dimethylhydrazine-induced rat model.

PubMed

Zhang, Ming; Fan, Xing; Fang, Bing; Zhu, Chengzhen; Zhu, Jun; Ren, Fazheng

2015-06-01

Probiotics have been suggested as a prophylactic measure in colon cancer. The aim of this study was to investigate the impact of Lactobacillus salivarius Ren (Ren) in modulating colonic microbiota structure and colon cancer incidence in a rat model after injection with 1,2-dimethyl hydrazine (DMH). The results indicated that oral administration of Ren could effectively suppress DMH-induced colonic carcinogenesis. A significant decrease in cancer incidence (87.5% to 25%) was detected in rats fed with a dose of 5 × 10(10) CFU/kg bodyweight per day. Using denaturing gradient gel electrophoresis and Real-time PCR combined with multivariate statistical methods, we demonstrated that injection with DMH significantly altered the rat gut microbiota, while Ren counteracted these DMH-induced adverse effects and promoted reversion of the gut microbiota close to the healthy state. Tvalue biplots followed by band sequencing identified 21 bacterial strains as critical variables affected by DMH and Ren. Injection of DMH significantly increased the amount of Ruminococcus species (sp.) and Clostridiales bacteria, as well as decreasing the Prevotella sp. Administration of Ren reduced the amount of Ruminococcus sp., Clostridiales bacteria, and Bacteroides dorei, and increased the amount of Prevotella. Real-time PCR results were consistent with the results derived by t-value biplots. These findings suggested that Ren is a potential agent for colon cancer prevention. In conclusion, the results in the present study suggest a potential therapeutic approach based on the modulation of intestinal microflora by probiotics may be beneficial in the prevention of colorectal carcinogenesis.

40 CFR 721.10159 - 1-Docosanamine, N,N-dimethyl-.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1-Docosanamine, N,N-dimethyl-. 721... Substances § 721.10159 1-Docosanamine, N,N-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as 1-docosanamine, N,N-dimethyl- (PMN P-07-587...

40 CFR 180.261 - N-(Mercaptomethyl) phthali-mide S-(O,O-dimethyl phosphoro-dithioate) and its oxygen analog...

Code of Federal Regulations, 2010 CFR

2010-07-01

...-dimethyl phosphoro-dithioate) and its oxygen analog; tolerances for residues. 180.261 Section 180.261...-mide S-(O,O-dimethyl phosphoro-dithioate) and its oxygen analog; tolerances for residues. (a) General...-(O,O-dimethyl phosphorodithioate) and its oxygen analog N-(mercaptomethyl) phthalimide S-(O,O...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Benzene, 1,2-dimethyl-, poly-propene... Significant New Uses for Specific Chemical Substances § 721.1225 Benzene, 1,2-dimethyl-, poly-propene... reporting. (1) The chemical substance identified as benzene, 1,2-dimethyl-, polypropene derivatives...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Benzene, 1,2-dimethyl-, poly-propene... Significant New Uses for Specific Chemical Substances § 721.1225 Benzene, 1,2-dimethyl-, poly-propene... reporting. (1) The chemical substance identified as benzene, 1,2-dimethyl-, polypropene derivatives...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Benzene, 1,2-dimethyl-, poly-propene... Significant New Uses for Specific Chemical Substances § 721.1225 Benzene, 1,2-dimethyl-, poly-propene... reporting. (1) The chemical substance identified as benzene, 1,2-dimethyl-, polypropene derivatives...

40 CFR 721.10159 - 1-Docosanamine, N,N-dimethyl-.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Docosanamine, N,N-dimethyl-. 721... Substances § 721.10159 1-Docosanamine, N,N-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as 1-docosanamine, N,N-dimethyl- (PMN P-07-587...

40 CFR 721.10366 - Benzene, 4-bromo-1,2-dimethyl-.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Benzene, 4-bromo-1,2-dimethyl-. 721... Substances § 721.10366 Benzene, 4-bromo-1,2-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as benzene, 4-bromo-1,2-dimethyl-(PMN P-10-76...

40 CFR 721.10366 - Benzene, 4-bromo-1,2-dimethyl-.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Benzene, 4-bromo-1,2-dimethyl-. 721... Substances § 721.10366 Benzene, 4-bromo-1,2-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as benzene, 4-bromo-1,2-dimethyl-(PMN P-10-76...

40 CFR 721.10366 - Benzene, 4-bromo-1,2-dimethyl-.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Benzene, 4-bromo-1,2-dimethyl-. 721... Substances § 721.10366 Benzene, 4-bromo-1,2-dimethyl-. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as benzene, 4-bromo-1,2-dimethyl-(PMN P-10-76...

A Process for Producing Highly Wettable Aluminum 6061 Surfaces Compatible with Hydrazine

NASA Technical Reports Server (NTRS)

Moore, N. R.; Ferraro, N. W.; Yue, A. F.; Estes, R. H.

2007-01-01

NASA's Global Precipitation Measurement (GPM) mission is an ongoing Goddard Space Flight Center (GSFC) project whose basic objective is to improve global precipitation measurements. The space-based portion of the mission architecture consists of a primary or core spacecraft and a constellation of NASA and contributed spacecrafts. The efforts described in this paper refer to the core spacecraft (hereafter referred to as simply GPM) which is to be fabricated at GSFC. It has been decided that the GPM spacecraft is to be a "design-for-demise-spacecraft." This requirement resulted in the need for a propellant tank that would also demise or ablate to an appropriate degree upon re-entry. Composite overwrapped aluminum lined propellant tanks with aluminum propellant management devices (PMD) were shown by analyses to demise and thus became the baseline configuration for GPM. As part of the GPM tank development effort, long term compatibility and wettability testing with hydrazine was performed on Al6061 and 2219 coupons fabricated and cleaned by conventional processes. Long term compatibility was confirmed. However, the wettability of the aluminum as measured by contact angle produced higher than desired angles (greater than 30 deg.) with excessive scatter. The availability of PMD materials exhibiting consistently low contact angles aids in the design of simple PMDs. Two efforts performed by Angeles Crest Engineering and funded by GSFC were undertaken to reduce the risk of using aluminum for the GPM PMD. The goal of the first effort was to develop a cleaning or treatment process to produce consistently low contact angles. The goal of the second effort was to prove via testing that the processed aluminum would retain compatibility with hydrazine and retain low contact angle after long term exposure to hydrazine. Both goals were achieved. This paper describes both efforts and the results achieved.

In vitro granulocyte adherence and in vivo margination: two associated complement-dependent functions. Studies based on the acute neutropenia of filtration leukophoresis.

PubMed

Fehr, J; Jacob, H S

1977-09-01

To study mechanisms and mediators regulating the distribution of intravascular granulocytes between circulating and marginated pools, a human model with extreme transient margination, the neutropenia of continuous flow filtration leukophoresis, was analyzed. Studies in animals demonstrated the existence of a complement (C)-derived granulocytopenia-inducing factor. Thus, autologous plasma, exposed to nylon fibers (NF) of the filtration system, produced an acute selective decrement of circulating granulocytes and monocytes. This phenomenon was blocked by decomplementing plasma, by pretreatment of plasma with EDTA or hydrazine, and by preheating at 56 degrees C, but did occur after recombination of heat-inactivated and hydrazine-treated plasma before NF exposure. Preheating plasma at 50 degrees C did not inhibit the neutropenic response, suggesting involvement of the classical pathway of C activation. Ultrafiltration studies indicated that the NF-provoked neutropenia-inducing factor has a mol wt in the range of 10,000-30,000, and is heat stable (56 degrees C). To analyze the hypothesis that C- induced neutrophil margination might be consequent to increased cell adhesiveness to endothelial surfaces, the role of C in promoting granulocyte adherence was evaluated in vitro. Measured with a plastic Petridish assay, granulocyte adherence was significantly reduced in heat- inactivated (56 degrees C) and hydrazine-treated plasma, but adherence promoting capacity was restored by mixing the two plasmas, or by adding purified C3 to hydrazine-treated plasma. After exposure to activated C, neutrophils showed significantly increased adhesiveness which was maintained when cells were resuspended in heat-inactivated plasma, but progressively lost when resuspended in fresh plasma. On the basis of these results we conclude that granulocyte adhesiveness in vitro and margination in vivo are closely associated, C-dependent phenomena.

H3 K79 dimethylation marks developmental activation of the beta-globin gene but is reduced upon LCR-mediated high-level transcription.

PubMed

Sawado, Tomoyuki; Halow, Jessica; Im, Hogune; Ragoczy, Tobias; Bresnick, Emery H; Bender, M A; Groudine, Mark

2008-07-15

Genome-wide analyses of the relationship between H3 K79 dimethylation and transcription have revealed contradictory results. To clarify this relationship at a single locus, we analyzed expression and H3 K79 modification levels of wild-type (WT) and transcriptionally impaired beta-globin mutant genes during erythroid differentiation. Analysis of fractionated erythroid cells derived from WT/Delta locus control region (LCR) heterozygous mice reveals no significant H3 K79 dimethylation of the beta-globin gene on either allele prior to activation of transcription. Upon transcriptional activation, H3 K79 di-methylation is observed along both WT and DeltaLCR alleles, and both alleles are located in proximity to H3 K79 dimethylation nuclear foci. However, H3 K79 di-methylation is significantly increased along the DeltaLCR allele compared with the WT allele. In addition, analysis of a partial LCR deletion mutant reveals that H3 K79 dimethylation is inversely correlated with beta-globin gene expression levels. Thus, while our results support a link between H3 K79 dimethylation and gene expression, high levels of this mark are not essential for high level beta-globin gene transcription. We propose that H3 K79 dimethylation is destabilized on a highly transcribed template.

40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

Code of Federal Regulations, 2014 CFR

2014-07-01

...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

Code of Federal Regulations, 2013 CFR

2013-07-01

...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

Code of Federal Regulations, 2012 CFR

2012-07-01

...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

40 CFR 721.10408 - Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene...

Code of Federal Regulations, 2013 CFR

2013-07-01

...)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2,2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl)oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...

40 CFR 721.10408 - Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene...

Code of Federal Regulations, 2014 CFR

2014-07-01

...)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2,2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl)oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...

40 CFR 721.10408 - Poly[oxy(methyl-1,2-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene...

Code of Federal Regulations, 2012 CFR

2012-07-01

...)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2,2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl) oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...-ethanediyl)], .alpha.-[2-[[2,2-dimethyl-3-[(1-oxododecyl)oxy]propylidene] amino] methylethyl]-.omega.-[2-[[2...

Microbial Transformations of Selenium

PubMed Central

Doran, J. W.; Alexander, M.

1977-01-01

Resting cell suspensions of a strain of Corynebacterium isolated from soil formed dimethyl selenide from selenate, selenite, elemental selenium, selenomethionine, selenocystine, and methaneseleninate. Extracts of the bacterium catalyzed the production of dimethyl selenide from selenite, elemental selenium, and methaneseleninate, and methylation of the inorganic Se compounds was enhanced by S-adenosylmethionine. Neither trimethylselenonium nor methaneselenonate was metabolized by the Corynebacterium. Resting cell suspensions of a methionine-utilizing pseudomonad converted selenomethionine to dimethyl diselenide. Six of 10 microorganisms able to grow on cystine used selenocystine as a sole source of carbon and formed elemental selenium, and one of the isolates, a pseudomonad, was found also to produce selenide. Soil enrichments converted trimethylselenonium to dimethyl selenide. Bacteria capable of utilizing trimethylselenonium, dimethyl selenide, and dimethyl diselenide as carbon sources were isolated from soil. PMID:16345188

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2013 CFR

2013-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2012 CFR

2012-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2011 CFR

2011-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.2465 - Xanthylium, 9-(2-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate.

Code of Federal Regulations, 2014 CFR

2014-07-01

...)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. 721.2465 Section 721.2465 Protection of...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate. (a) Chemical substance and significant...-(ethoxycarbonyl)phenyl)-3,6-bis(ethylamino)-2,7-dimethyl-, ethyl sulfate (PMN P-00-1195; CAS No. 26694-69-9) is...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts (PMN P-03-46; CAS No. 136504-87-5) is subject to...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts (PMN P-03-46; CAS No. 136504-87-5) is subject to...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts (PMN P-03-46; CAS No. 136504-87-5) is subject to...

40 CFR 721.10174 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

...-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts. 721.10174 Section 721.10174 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts. (a) Chemical substance...-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts (PMN P-04-139...

HAN-Based Monopropellant Propulsion System with Applications

NASA Technical Reports Server (NTRS)

Jankovsky, Robert S.; Oleson, Steven R.

1997-01-01

NASA is developing a new monopropellant propulsion system for small, cost-driven spacecraft with AV requirements in the range of 10-150 m/sec. This system is based on a hydroxylammonium nitrate (HAN)/water/fuel monopropellant blend which is extremely dense, environmentally benign, and promises good performance and simplicity. State-of-art (SOA) small spacecraft typically employ either hydrazine or high pressure stored gas. Herein, a 'typical' small satellite bus is used to illustrate how a HAN-based monopropellant propulsion system fulfills small satellite propulsion requirements by providing mass and/or volume savings of SOA hydrazine monopropellants with the cost benefits of a stored nitrogen gas.

[Progress in the protective medicine against [correction of aganist] rocket propellents].

PubMed

Hu, W X; Tan, C Y; Tan, S J; Jiang, J

1999-12-01

To review the progress in the major assignment, the organization and implementation of protection against liquid rocket propellent. The safety detection methods of the rocket [correction of rocked] propellent in the launching field were also discussed. Three steps of the sanitation and protection of the liquid propellent, the toxicity and the toxicology of hydrazine on central nervous system, blood circulatory system, assimilation system, respiratory system, immune system, liver, kidney, eye, skin and its hereditary toxicology were described. In addition, the clinical types of poisoning, the current principle and the common ways of the prevention and treatment of hydrazine and nitrogen oxides poisoning were summarized.

Analysis and design of the Multimission Modular Spacecraft hydrazine propulsion module

NASA Technical Reports Server (NTRS)

Etheridge, F. G.; Woodruff, W. L.

1978-01-01

The translational velocity increment, stabilization and control requirements, vehicle weight, and geometric considerations of the Multimission Modular Spacecraft (MMS) provided the basic data on which to initiate the analysis and design of the hydrazine propulsion modules. The Landsat D was used as the mission model. Tradeoff studies were conducted on thrust level, thruster location, and clustering arrangement together with tankage volume and location. The impact of the use of single and dual seat thruster valves on plumbing configuration, reliability, and overall system cost was studied in detail. Conceptual designs of a recommended propulsion module configuration for both the Delta 3910 and Shuttle were prepared.

Proposed Amendment to the Final Decision Document for the Hydrazine Blending and Storage Facility, Interim Response Action

DTIC Science & Technology

1991-02-25

OerAtlonl n eor$. 12.15 eflerne tHI IRE III N~ l~l 1111 111111 [10 liii 0I tr. oOffýe of Ni’a eerTe~ n.’ gmo e !oe. ojporcrm. q.,ucto, 9,r7ect f0704-0...Sewage Treatment Plant (STP) of hydrazine wastewater treated to 5 pg/l of NDMA. AEHA’s findings were published in a study released to PMRMA on October 22...the disposal alternative, the EPA would not issue a National Pollutant Discharge Elimination System (NPDES) permit to allow disposal of the treated

An Overview of Demise Calculations, Conceptual Design Studies, and Hydrazine Compatibility Testing for the GPM Core Spacecraft Propellant Tank

NASA Technical Reports Server (NTRS)

Estes, Robert H.; Moore, N. R.

2007-01-01

NASA's Global Precipitation Measurement (GPM) mission is an ongoing Goddard Space Flight Center (GSFC) project whose basic objective is to improve global precipitation measurements. It has been decided that the GPM spacecraft is to be a "design for demise" spacecraft. This requirement resulted in the need for a propellant tank that would also demise or ablate to an appropriate degree upon re-entry. This paper will describe GSFC-performed spacecraft and tankage demise analyses, vendor conceptual design studies, and vendor performed hydrazine compatibility and wettability tests performed on 6061 and 2219 aluminum alloys.

Historical perspective - Viking Mars Lander propulsion

NASA Technical Reports Server (NTRS)

Morrisey, Donald C.

1989-01-01

This paper discusses the Viking 1 and 2 missions to Mars in 1975-1976 and describes the design evolution of the Viking Terminal Descent Rocket Engines responsible for decelerating the Viking Mars Landers during the final portion of their descent from orbit. The Viking Terminal Descent Rocket Engines have twice the thrust of the largest monopropellant hydrazine engine developed previously but weigh considerably less. The engine has 18 nozzles, the capability of 10:1 throttling, is totally sealed until fired, employs no organic unsealed materials, is 100 percent germ free, utilized hydrazine STM-20 as the propellant, and starts at a temperature more than 45 F below the propellant's freezing point.

Luminescent detection of hydrazine and hydrazine derivatives

DOEpatents

Swager, Timothy M [Newton, MA; Thomas, III, Samuel W.

2012-04-17

The present invention generally relates to methods for modulating the optical properties of a luminescent polymer via interaction with a species (e.g., an analyte). In some cases, the present invention provides methods for determination of an analyte by monitoring a change in an optical signal of a luminescent polymer upon exposure to an analyte. Methods of the present invention may be useful for the vapor phase detection of analytes such as explosives and toxins. The present invention also provides methods for increasing the luminescence intensity of a polymer, such as a polymer that has been photobleached, by exposing the luminescent polymer to a species such as a reducing agent.

Thermal design of the IUE hydrazine auxiliary propulsion system. [International Ultraviolet Explorer

NASA Technical Reports Server (NTRS)

Skladany, J. T.; Kelly, W. H.

1977-01-01

The International Ultraviolet Explorer is a large astronomical observatory scheduled to be placed in a three-axis stabilized synchronous orbit in the fourth quarter of 1977. The Hydrazine Auxiliary Propulsion System (HAPS) must perform a number of spacecraft maneuvers to achieve a successful mission. This paper describes the thermal design which accomplishes temperature control between 5 and 65 C for all orbital conditions by utilizing multilayer insulation and commandable component heaters. A primary design criteria was the minimization of spacecraft power by the selective use of the solar environment. The thermal design was carefully assessed and verified in both spacecraft thermal balance and subsystem solar simulation testing.

Using Hydrazine to Link Ferrocene with Re(CO)3: A Modular Approach.

PubMed

Chanawanno, Kullapa; Rhoda, Hannah M; Hasheminasab, Abed; Crandall, Laura A; King, Alexander J; Herrick, Richard S; Nemykin, Victor N; Ziegler, Christopher J

2016-09-01

Acetyl ferrocene and diacetyl ferrocene both readily react with an excess of hydrazine to afford the corresponding hydrazone compounds. These compounds can then be linked to Re(CO) 3 via a metal-mediated Schiff base reaction, resulting in a series of ferrocene-Re(CO) 3 conjugates with different stoichiometries. Conjugates with 1:1, 1:2, and 2:1 ferrocene: Re(CO) 3 ratios can be produced via this "modular" type synthesis approach. Several examples of these conjugates were structurally characterized, and their spectroscopic, electrochemical, and spectroelectrochemical behaviors were investigated. The electronic structures of these compounds were also probed using DFT and TDDFT calculations.

The development of a non-cryogenic nitrogen/oxygen supply system

NASA Technical Reports Server (NTRS)

Greenough, B. M.

1972-01-01

Development of the hydrazine/water electrolysis process in a manned spacecraft to provide metabolic oxygen and both oxygen and nitrogen for cabin leakage makeup was studied. Electrode development efforts were directed to stability, achieved with catalyst additives and improved processing techniques, and a higher hydrazine conversion efficiency, achieved by reducing catalyst loading on the cathodes. Extensive testing of the one-man breadboard N2/02 system provided complete characterization of cabin atmosphere control aspects. A detailed design of a prototype modular N2/02 unit was conducted. The contact heat exchanger which is an integral component of this design was fabricated and sucessfully design-verification tested.

High-yielding and photolabile approaches to the covalent attachment of biomolecules to surfaces via hydrazone chemistry.

PubMed

Lee, Ju Hun; Domaille, Dylan W; Noh, Hyunwoo; Oh, Taeseok; Choi, Chulmin; Jin, Sungho; Cha, Jennifer N

2014-07-22

The development of strategies to couple biomolecules covalently to surfaces is necessary for constructing sensing arrays for biological and biomedical applications. One attractive conjugation reaction is hydrazone formation--the reaction of a hydrazine with an aldehyde or ketone--as both hydrazines and aldehydes/ketones are largely bioorthogonal, which makes this particular reaction suitable for conjugating biomolecules to a variety of substrates. We show that the mild reaction conditions afforded by hydrazone conjugation enable the conjugation of DNA and proteins to the substrate surface in significantly higher yields than can be achieved with traditional bioconjugation techniques, such as maleimide chemistry. Next, we designed and synthesized a photocaged aryl ketone that can be conjugated to a surface and photochemically activated to provide a suitable partner for subsequent hydrazone formation between the surface-anchored ketone and DNA- or protein-hydrazines. Finally, we exploit the latent functionality of the photocaged ketone and pattern multiple biomolecules on the same substrate, effectively demonstrating a strategy for designing substrates with well-defined domains of different biomolecules. We expect that this approach can be extended to the production of multiplexed assays by using an appropriate mask with sequential photoexposure and biomolecule conjugation steps.

Alternative bases in the RNA world: the prebiotic synthesis of urazole and its ribosides

NASA Technical Reports Server (NTRS)

Kolb, V. M.; Dworkin, J. P.; Miller, S. L.

1994-01-01

Urazole is a five-membered heterocyclic compound which is isosteric with uracil's hydrogen-bonding segment. Urazole reacts spontaneoulsy with ribose (and other aldoses) to give a mixture of four ribosides: alpha and beta pyranosides and furanosides. This reaction occurs in aqueous solution at mild temperatures. Thermodynamic and kinetic parameters for the reaction of urazole with ribose were determined. In contrast, uracil is completely unreactive with ribose under these conditions. Urazole's unusual reactivity is ascribed to the hydrazine portion of the molecule. Urazole can be synthesized from biuret and hydrazine under prebiotic conditions. The prebiotic synthesis of guanazole, which is isosteric in part to diaminopyrimidine and cytosine, is accomplished from dicyandiamide and hydrazine. Kinetic parameters for both prebiotic reactions were measured. Urazole and guanazole are transparent in the UV, which would be a favorable property in the absence of an ozone layer on the early Earth. Urazole makes hydrogen bonds with adenine in DMSO similar to those of uracil, as established by H NMR. All of these properties make urazole an attractive potential precursor to uracil and guanazole a potential precursor to cytosine in the RNA or pre-RNA world.

Formation of Nitrogen and Hydrogen-bearing Molecules in Solid Ammonia and Implications for Solar System and Interstellar Ices

NASA Astrophysics Data System (ADS)

Zheng, Weijun; Jewitt, David; Osamura, Yoshihiro; Kaiser, Ralf I.

2008-02-01

We irradiated solid ammonia (NH3) in the temperature range of 10-60 K with high-energy electrons to simulate the processing of ammonia-bearing ices in the interstellar medium and in the solar system. By monitoring the newly formed molecules online and in situ, the synthesis of hydrazine (N2H4), diazene (N2H2 isomers), hydrogen azide (HN3), the amino radical (NH2), molecular hydrogen (H2), and molecular nitrogen (N2) has been confirmed. Our results show that the production rates of hydrazine, diazene, hydrogen azide, molecular hydrogen, and molecular nitrogen are higher in amorphous ammonia than those in crystalline ammonia; this behavior is similar to the production of molecular hydrogen, molecular oxygen, and hydrogen peroxide found in electron-irradiated water ices. However, the formation of hydrazine in crystalline ammonia does not show any temperature dependence. Our experimental results give hints to the origin of molecular nitrogen in the Saturnian system and possibly in the atmospheres of proto-Earth and Titan; our research may also guide the search of hitherto unobserved nitrogen-bearing molecules in the interstellar medium and in our solar system.

Potential biofouling of spacecraft propellant systems due to contaminated deionized water

NASA Astrophysics Data System (ADS)

Hogue, Patrick

2006-08-01

Deionized (DI) water, with a density close to hydrazine, is used to fill spacecraft propellant tanks for mechanical testing during ground operations, after which is it removed and the tanks dried for use with anhydrous hydrazine. Pure nitrogen is used as a pressurant during storage and during water fill and drain operations. Since DI water systems are notorious for contamination by slime-forming bacteria, DI water intended for use in New Horizons and STEREO hydrazine tanks at APL was assessed for microorganism content using the heterotrophic plate count (HPC) method. Results show that some growth occurred during storage of DI water in propellant tanks, however not at the logarithmic rate associated with well-nourished bacteria. Ralstonia and Burkholderia were present in DI water on-loaded however only Ralstonia was present in off-loaded water. One possible source of nutrients during water storage in propellant tanks is organic material originating from the EPDM (EPR per AF-E-332) expulsion diaphragm. This paper will demonstrate potential for bio-fouling of spacecraft propulsion systems due to growth of slime-forming bacteria and will suggest that specifications controlling microorganism content should be imposed on water used for spacecraft ground testing.

Structure investigation of three hydrazones Schiff's bases by spectroscopic, thermal and molecular orbital calculations and their biological activities

NASA Astrophysics Data System (ADS)

Belal, Arafa A. M.; Zayed, M. A.; El-Desawy, M.; Rakha, Sh. M. A. H.

2015-03-01

Three Schiff's bases AI (2(1-hydrazonoethyl)phenol), AII (2, 4-dibromo 6-(hydrazonomethyl)phenol) and AIII (2(hydrazonomethyl)phenol) were prepared as new hydrazone compounds via condensation reactions with molar ratio (1:1) of reactants. Firstly by reaction of 2-hydroxy acetophenone solution and hydrazine hydrate; it gives AI. Secondly condensation between 3,5-dibromo-salicylaldehyde and hydrazine hydrate gives AII. Thirdly condensation between salicylaldehyde and hydrazine hydrate gives AIII. The structures of AI-AIII were characterized by elemental analysis (EA), mass (MS), FT-IR and 1H NMR spectra, and thermal analyses (TG, DTG, and DTA). The activation thermodynamic parameters, such as, ΔE∗, ΔH∗, ΔS∗ and ΔG∗ were calculated from the TG curves using Coats-Redfern method. It is important to investigate their molecular structures to know the active groups and weak bond responsible for their biological activities. Consequently in the present work, the obtained thermal (TA) and mass (MS) practical results are confirmed by semi-empirical MO-calculations (MOCS) using PM3 procedure. Their biological activities have been tested in vitro against Escherichia coli, Proteus vulgaris, Bacillissubtilies and Staphylococcus aurous bacteria in order to assess their anti-microbial potential.

Antioxidant properties of dimethyl sulfoxide and its viability as a solvent in the evaluation of neuroprotective antioxidants.

PubMed

Sanmartín-Suárez, Carolina; Soto-Otero, Ramón; Sánchez-Sellero, Inés; Méndez-Álvarez, Estefanía

2011-01-01

Dimethyl sulfoxide is an amphiphilic compound whose miscibility with water and its ability to dissolve lipophilic compounds make it an appreciated solvent in biomedical research. However, its reported antioxidant properties raise doubts about its use as a solvent in evaluating new antioxidants. The goal of this investigation was to evaluate its antioxidant properties and carry out a comparative study on the antioxidant properties of some known neuroprotective antioxidants in the presence and absence of dimethyl sulfoxide. The antioxidant properties of dimethyl sulfoxide were studied in rat brain homogenates by determining its ability to reduce both lipid peroxidation (TBARS formation) and protein oxidation (increase in protein carbonyl content and decrease in free thiol content) induced by ferrous chloride/hydrogen peroxide. Its ability to reduce the production of hydroxyl radicals by 6-hydroxydopamine autoxidation was also estimated. The same study was also performed with three known antioxidants (α-phenyl-N-tert-butylnitrone; 2-methyl-2-nitrosopropane; 5,5-dimethyl-1-pyrroline N-oxide) in the presence and absence of dimethyl sulfoxide. Our results showed that dimethyl sulfoxide is able to reduce both lipid peroxidation and protein carbonyl formation induced by ferrous chloride/hydrogen peroxide in rat brain homogenates. It can also reduce the production of hydroxyl radicals during 6-hydroxydopamine autoxidation. However, it increases the oxidation of protein thiol groups caused by ferrous chloride/hydrogen peroxide in rat brain homogenate. Despite the here reported antioxidant and pro-oxidant properties of dimethyl sulfoxide, the results obtained with α-phenyl-N-tert-butylnitrone, 2-methyl-2-nitrosopropane, and 5,5-dimethyl-1-pyrroline N-oxide corroborate the antioxidant properties attributed to these compounds and support the potential use of dimethyl sulfoxide as a solvent in the study of the antioxidant properties of lipophilic compounds. Dimethyl sulfoxide is a very useful solvent that may be used at relatively low concentrations in the development of new antioxidants with neuroprotective properties. Copyright © 2010 Elsevier Inc. All rights reserved.

Thermodynamic equilibrium calculations of dimethyl ether steam reforming and dimethyl ether hydrolysis

NASA Astrophysics Data System (ADS)

Semelsberger, Troy A.; Borup, Rodney L.

The production of a hydrogen-rich fuel-cell feed by dimethyl ether (DME) steam reforming was investigated using calculations of thermodynamic equilibrium as a function of steam-to-carbon ratio (0.00-4.00), temperature (100-600 °C), pressure (1-5 atm), and product species. Species considered were acetone, acetylene, carbon dioxide, carbon monoxide, dimethyl ether, ethane, ethanol, ethylene, formaldehyde, formic acid, hydrogen, isopropanol, methane, methanol, methyl-ethyl ether, n-propanol and water. Thermodynamic equilibrium calculations of DME steam reforming indicate complete conversion of dimethyl ether to hydrogen, carbon monoxide and carbon dioxide at temperatures greater than 200 °C and steam-to-carbon ratios greater than 1.25 at atmospheric pressure ( P = 1 atm). Increasing the operating pressure shifts the equilibrium toward the reactants; increasing the pressure from 1 to 5 atm decreases the conversion of dimethyl ether from 99.5 to 76.2%. The trend of thermodynamically stable products in decreasing mole fraction is methane, ethane, isopropyl alcohol, acetone, n-propanol, ethylene, ethanol, methyl-ethyl ether and methanol-formaldehyde, formic acid, and acetylene were not observed. Based on the equilibrium calculations, the optimal processing conditions for dimethyl ether steam reforming occur at a steam-to-carbon ratio of 1.50, a pressure of 1 atm, and a temperature of 200 °C. These thermodynamic equilibrium calculations show dimethyl ether processed with steam will produce hydrogen-rich fuel-cell feeds—with hydrogen concentrations exceeding 70%. The conversion of dimethyl ether via hydrolysis (considering methanol as the only product) is limited by thermodynamic equilibrium. Equilibrium conversion increases with temperature and steam-to-carbon ratio. A maximum dimethyl ether conversion of 62% is achieved at a steam-to-carbon ratio of 5.00 and a processing temperature of 600 °C.

Selectivity control of carbonylation of methanol to dimethyl oxalate and dimethyl carbonate over gold anode by electrochemical potential.

PubMed

Funakawa, Akiyasu; Yamanaka, Ichiro; Takenaka, Sakae; Otsuka, Kiyoshi

2004-05-05

New and unique electrocatalysis of gold for the carbonylation of methanol to dimethyl oxalate (DMO) and dimethyl carbonate (DMC) was found. The selectivity to DMO and DMC could be controlled over gold anode by electrochemical potential, as you like. Drastic changes of gold electrocatalysis was due to changes of the oxidation state of gold, Au0 or Au3+.

Collection and analysis of organic gases from natural ecosystems - Application to poultry manure

NASA Technical Reports Server (NTRS)

Smith, M. S.; Francis, A. J.; Duxbury, J. M.

1977-01-01

Combined gas chromatography-mass spectrometry was used to identify volatile compounds generated from chicken manure and collected in Poropak QS-Carbosieve B traps. Various alcohols, ketones, esters, and carboxylic acids together with dimethyl sulfide and dimethyl disulfide were detected when the wastes were incubated in an argon atmosphere. Significant amounts of dimethyl sulfide and dimethyl disulfide but few other compounds were found when the manure was incubated in air

A chromene and prenylated benzoic acid from Piper aduncum.

PubMed

Baldoqui, D C; Kato, M J; Cavalheiro, A J; Bolzani, V da S; Young, M C; Furlan, M

1999-08-01

In addition to nerolidol, 2',6'-dihydroxy-4'-methoxydihydrochalcone, methyl 2,2-dimethyl-8-(3'-methyl-2'-butenyl)-2H-1-chromene-6-carboxylate, methyl 2,2-dimethyl-2H-1-chromene-6-carboxylate and methyl 8-hydroxy-2,2-dimethyl-2H-1-chromene-6-carboxylate, two new natural products were isolated from the leaves of Piper aduncum, 2,2-dimethyl-2H-1-chromene-6-carboxylic acid and 3-(3',7'-dimethyl-2',6'-octadienyl)-4-methoxybenzoic acid. The structures of the isolates were established based on analysis of spectroscopic data, including ES-MS. The DNA-damaging activity of the isolated compounds was also investigated against mutant strains of Saccharomyces cerevisiae.

Loss mechanisms in hydrazine-processed Cu2ZnSn(Se,S)4 solar cells

NASA Astrophysics Data System (ADS)

Gunawan, Oki; Todorov, Teodor K.; Mitzi, David B.

2010-12-01

We present a device characterization study for hydrazine-processed kesterite Cu2ZnSn(Se,S)4 (CZTSSe) solar cells with a focus on pinpointing the main loss mechanisms limiting device efficiency. Temperature-dependent study and time-resolved photoluminescence spectroscopy on these cells, in comparison to analogous studies on a reference Cu(In,Ga)(Se,S)2 (CIGS) cell, reveal strong recombination loss at the CZTSSe/CdS interface, very low minority-carrier lifetimes, and high series resistance that diverges at low temperature. These findings help identify the key areas for improvement of these CZTSSe cells in the quest for a high-performance indium- and tellurium-free solar cell.

Liquid-phase chemical hydrogen storage: catalytic hydrogen generation under ambient conditions.

PubMed

Jiang, Hai-Long; Singh, Sanjay Kumar; Yan, Jun-Min; Zhang, Xin-Bo; Xu, Qiang

2010-05-25

There is a demand for a sufficient and sustainable energy supply. Hence, the search for applicable hydrogen storage materials is extremely important owing to the diversified merits of hydrogen energy. Lithium and sodium borohydride, ammonia borane, hydrazine, and formic acid have been extensively investigated as promising hydrogen storage materials based on their relatively high hydrogen content. Significant advances, such as hydrogen generation temperatures and reaction kinetics, have been made in the catalytic hydrolysis of aqueous lithium and sodium borohydride and ammonia borane as well as in the catalytic decomposition of hydrous hydrazine and formic acid. In this Minireview we briefly survey the research progresses in catalytic hydrogen generation from these liquid-phase chemical hydrogen storage materials.

U.S. Space Station Freedom waste fluid disposal system with consideration of hydrazine waste gas injection thrusters

NASA Technical Reports Server (NTRS)

Winters, Brian A.

1990-01-01

The results are reported of a study of various methods for propulsively disposing of waste gases. The options considered include hydrazine waste gas injection, resistojets, and eutectic salt phase change heat beds. An overview is given of the waste gas disposal system and how hydrozine waste gas injector thruster is implemented within it. Thruster performance for various gases are given and comparisons with currently available thruster models are made. The impact of disposal on station propellant requirements and electrical power usage are addressed. Contamination effects, reliability and maintainability assessments, safety issues, and operational scenarios of the waste gas thruster and disposal system are considered.

Hydrazine-Free Solution-Deposited CuIn(S,Se)2 Solar Cells by Spray Deposition of Metal Chalcogenides.

PubMed

Arnou, Panagiota; van Hest, Maikel F A M; Cooper, Carl S; Malkov, Andrei V; Walls, John M; Bowers, Jake W

2016-05-18

Solution processing of semiconductors, such as CuInSe2 and its alloys (CIGS), can significantly reduce the manufacturing costs of thin film solar cells. Despite the recent success of solution deposition approaches for CIGS, toxic reagents such as hydrazine are usually involved, which introduce health and safety concerns. Here, we present a simple and safer methodology for the preparation of high-quality CuIn(S, Se)2 absorbers from metal sulfide solutions in a diamine/dithiol mixture. The solutions are sprayed in air, using a chromatography atomizer, followed by a postdeposition selenization step. Two different selenization methods are explored resulting in power conversion efficiencies of up to 8%.

Hydrazines and carbohydrazides produced from oxidized carbon in earth's primitive environment

NASA Technical Reports Server (NTRS)

Folsome, C. E.; Brittain, A.; Smith, A.; Chang, S.

1981-01-01

Whether abiological organic compounds can be formed from the interactions of energy sources with nitrogen, oxidized carbon and water is held to be of importance in geochemical models of the primordial earth atmosphere. It is reported that experiments using quenched spark discharges through molecular nitrogen on aqueous suspensions of CaCO3 and other reactants to simulate the hydrosphere/atmosphere interface yield hydrazine and carbohydrazine in significant but low yields. Such reactions in primitive aquatic environments may have supplied a pathway for chemical evolution and the origin of life, on a primitive earth in which fully oxidized states of carbon were available for the primary synthesis of organic matter.

Hydrogenation of liquid natural rubber via diimide reduction in hydrazine hydrate/hydrogen peroxide system

NASA Astrophysics Data System (ADS)

Yusof, Muhammad Jefri Mohd; Jamaluddin, Naharullah; Abdullah, Ibrahim; Yusoff, Siti Fairus M.

2015-09-01

Liquid natural rubber (LNR) with molecular weight of lower than 105 and shorter polymeric chain than natural rubber was prepared. LNR was then hydrogenated via diimide reduction by oxidation of hydrazine hydrate with hydrogen peroxide. The unsaturated units of the rubber were converted into saturated hydrocarbon to strengthen the backbone of the polymer so it was able to resist thermal degradation. The results indicated that hydrogenation degree of the product (HLNR) could be extended to 91.2% conversion under appropriate conditions. The hydrogenated LNR (HLNR) was characterized using Fourier-Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. The physical characteristics of HLNR were analyzed with Termogravimetric Analysis (TGA).

Asymmetric synthesis of N-allylic indoles via regio- and enantioselective allylation of aryl hydrazines

PubMed Central

Xu, Kun; Gilles, Thomas; Breit, Bernhard

2015-01-01

The asymmetric synthesis of N-allylic indoles is important for natural product synthesis and pharmaceutical research. The regio- and enantioselective N-allylation of indoles is a true challenge due to the favourable C3-allylation. We develop here a new strategy to the asymmetric synthesis of N-allylic indoles via rhodium-catalysed N-selective coupling of aryl hydrazines with allenes followed by Fischer indolization. The exclusive N-selectivities and good to excellent enantioselectivities are achieved applying a rhodium(I)/DTBM-Segphos or rhodium(I)/DTBM-Binap catalyst. This method permits the practical synthesis of valuable chiral N-allylated indoles, and avoids the N- or C-selectivity issue. PMID:26137886

The hard start phenomena in hypergolic engines. Volume 4: The chemistry of hydrazine fuels and nitrogen tetroxide propellant systems

NASA Technical Reports Server (NTRS)

Miron, Y.; Perlee, H. E.

1974-01-01

The various chemical reactions that occur and that could possibly occur in the RCS engines utilizing hydrazine-type fuel/nitrogen tetroxide propellant systems, prior to ignition (preignition), during combustion, and after combustion (postcombustion), and endeavors to relate the hard-start phenomenon to some of these reactions are discussed. The discussion is based on studies utilizing a variety of experimental techniques and apparatus as well as current theories of chemical reactions and reaction kinetics. The chemical reactions were studied in low pressure gas flow reactors, low temperature homogeneous- and heterogeneous-phase reactors, simulated two-dimensional (2-D) engines, and scaled and full size engines.

Monopropellant engine investigation for space shuttle reaction control system. Volume 3: Improvement of metal foam for catalyst retention

NASA Technical Reports Server (NTRS)

1975-01-01

The retention of granular catalyst in a metal foam matrix was demonstrated to greatly increase the life capability of hydrazine monopropellant reactors. Since nickel foam used in previous tests was found to become degraded after long-term exposure the cause of degradation was examined and metal foams of improved durability were developed. The most durable foam developed was a rhodium-coated nickel foam. An all-platinum foam was found to be incompatible in a hot ammonia (hydrazine) environment. It is recommended to scale up the manufacturing process for the improved foam to produce samples sufficiently large for space shuttle APU gas generator testing.

Highly durable direct hydrazine hydrate anion exchange membrane fuel cell

NASA Astrophysics Data System (ADS)

Sakamoto, Tomokazu; Serov, Alexey; Masuda, Teruyuki; Kamakura, Masaki; Yoshimoto, Koji; Omata, Takuya; Kishi, Hirofumi; Yamaguchi, Susumu; Hori, Akihiro; Horiuchi, Yousuke; Terada, Tomoaki; Artyushkova, Kateryna; Atanassov, Plamen; Tanaka, Hirohisa

2018-01-01

The factors influenced on degradation of direct hydrazine hydrate fuel cells (DHFCs) under operation conditions are analyzed by in situ soft X-ray radiography. A durability of DHFCs is significantly improved by multi-step reaction DHFCs (MSR-DHFCs) approach designed to decrease the crossover of liquid fuel. An open circuit voltage (OCV) as well as cell voltage at 5 mA cm-2 of MSR-DHFC construct with commercial anion exchange membrane (AEM) maintained for over of 3500 h at 60 °C. Furthermore, the commercial proton exchange membrane (PEM) is integrated into AEM of MSR-DHFCs resulting in stable power output of MSR-DHFCs for over than 2800 h at 80 °C.

Catalysts for the decomposition of hydrazine and its derivatives and a method for its production

NASA Technical Reports Server (NTRS)

Sasse, R.

1986-01-01

Catalysts of various types are used to decompose hydrazine and its derivatives. One type of catalyst is made as follows: the aluminum is dissolved out of an alloy of cobalt or nickel/aluminum so that a structure is produced that is chemically active for the monergol and that has a large active surface. The objective was to avoid difficulties and to create a catalyst that not only has a short start time but that can also be manufactured easily and relatively inexpensively. The solution to this task is to coat the base structure of the catalyst with oxides of copper, cobalt and cerium or oxides of copper, cobalt and cerite earth.

Synthesis of peptide .alpha.-thioesters

DOEpatents

Camarero, Julio A [Livermore, CA; Mitchell, Alexander R [Livermore, CA; De Yoreo, James J [Clayton, CA

2008-08-19

Disclosed herein is a new method for the solid phase peptide synthesis (SPPS) of C-terminal peptide .alpha. thioesters using Fmoc/t-Bu chemistry. This method is based on the use of an aryl hydrazine linker, which is totally stable to conditions required for Fmoc-SPPS. When the peptide synthesis has been completed, activation of the linker is achieved by mild oxidation. The oxidation step converts the acyl-hydrazine group into a highly reactive acyl-diazene intermediate which reacts with an .alpha.-amino acid alkylthioester (H-AA-SR) to yield the corresponding peptide .alpha.-thioester in good yield. A variety of peptide thioesters, cyclic peptides and a fully functional Src homology 3 (SH3) protein domain have been successfully prepared.

Management Strategies to Facilitate Optimal Outcomes for Patients Treated with Delayed-release Dimethyl Fumarate.

PubMed

Mayer, Lori; Fink, Mary Kay; Sammarco, Carrie; Laing, Lisa

2018-04-01

Delayed-release dimethyl fumarate is an oral disease-modifying therapy that has demonstrated significant efficacy in adults with relapsing-remitting multiple sclerosis. Incidences of flushing and gastrointestinal adverse events are common in the first month after delayed-release dimethyl fumarate initiation. Our objective was to propose mitigation strategies for adverse events related to initiation of delayed-release dimethyl fumarate in the treatment of patients with multiple sclerosis. Studies of individually developed mitigation strategies and chart reviews were evaluated. Those results, as well as mitigation protocols developed at multiple sclerosis care centers, are summarized. Key steps to optimize the effectiveness of delayed-release dimethyl fumarate treatment include education prior to and at the time of delayed-release dimethyl fumarate initiation, initiation dose protocol gradually increasing to maintenance dose, dietary suggestions for co-administration with food, gastrointestinal symptom management with over-the-counter medications, flushing symptom management with aspirin, and temporary dose reduction. Using the available evidence from clinical trials and evaluations of post-marketing studies, these strategies to manage gastrointestinal and flushing symptoms can be effective and helpful to the patient when initiating delayed-release dimethyl fumarate.

Decryptification of Acid Phosphatase in Arthrospores of Geotrichum Species Treated with Dimethyl Sulfoxide and Acetone

PubMed Central

Cotter, David A.; Martel, Anita J.; MacDonald, Paul

1975-01-01

Decryptification of acid phosphatase in Geotrichum sp. arthrospores was accomplished using acetone or dimethyl sulfoxide treatment. Both dimethyl sulfoxide and acetone irreversibly destroyed the integrity of the spore membranes without solubilizing acid phosphatase. PMID:1167386

Inert Reassessment Document for Dimethyl Ether - CAS No. 115-10-6

EPA Pesticide Factsheets

The existing dimethyl ether exemption from the requirement of a tolerance under 40 CFR 180.930 is for use on animals only. Dimethyl ether is used as an inert ingredient in a variety of livestock insect sprays and foggers.

Effect of vanadium on colonic aberrant crypt foci induced in rats by 1,2 Dimethyl hydrazine

PubMed Central

Kanna, P Suresh; Mahendrakumar, CB; Chakraborty, T; Hemalatha, P; Banerjee, Pratik; Chatterjee, M

2003-01-01

AIM: To investigate the chemo preventive effects of vanadium on rat colorectal carcinogenesis induced by 1,2-dimethylhydrazine (DMH). METHODS: Male Sprague-Dawley Rats were randomly divided into four groups. Rats in Group A received saline vehicle alone for 16 weeks. Rats in Group B were given DMH injection once a week intraperitoneally for 16 weeks; rats in Group C, with the same DMH treatment as in the Group B, but received 0.5-ppm vanadium in the form ammonium monovanadate ad libitum in drinking water. Rats in the Group D received vanadium alone as in the Group C without DMH injection. RESULTS: Aberrant crypt foci (ACF) were formed in animals in DMH-treated groups at the end of week 16. Compared to DMH group, vanadium treated group had less ACF (P < 0.001). At the end of week 32, all rats in DMH group developed large intestinal tumors. Rats treated with vanadium contained significantly few colonic adenomas and carcinomas (P < 0.05) compared to rats administered DMH only. In addition, a significant reduction (P < 0.05) in colon tumor burden (sum of tumor sizes per animal) was also evident in animals of Group C when compared to those in rats of carcinogen control Group B. The results also showed that vanadium significantly lowered PCNA index in ACF (P < 0.005). Furthermore, vanadium supplementation also elevated liver GST and Cyt P-450 activities (P < 0.001 and P < 0.02, respectively). CONCLUSION: Vanadium in the form of ammonium monovanadate supplemented in drinking water ad libitum has been found to be highly effective in reducing tumor incidence and preneoplastic foci on DMH-induced colorectal carcinogenesis. These findings suggest that vanadium administration can suppress colon carcinogenesis in rats. PMID:12717849

Astaxanthin inhibits tumor invasion by decreasing extracellular matrix production and induces apoptosis in experimental rat colon carcinogenesis by modulating the expressions of ERK-2, NFkB and COX-2.

PubMed

Nagendraprabhu, Ponnuraj; Sudhandiran, Ganapasam

2011-04-01

Colon cancer is the third most malignant neoplasm in the world and it remains an important cause of mortality in Asian and Western countries. Astaxanthin (AST), a major component of carotenoids possesses attractive remedial features. The purpose of this study is to investigate the possible mechanism of action of astaxanthin against 1, 2 dimethyl hydrazine (DMH)-induced rat colon carcinogenesis. Wistar male rats were randomized into five groups, group 1 were control rats, group 2 were rats that received AST (15 mg/kg body wt p.o. everyday), rats in group 3 were induced with DMH (40 mg/kg body wt, s.c.), DMH-induced rats in groups 4 and 5 were either pre or post initiated with AST, respectively as in group 2. DMH-induced rats exhibited elevated expressions of Nuclear factor kappa B-p65 (NF-κB-p65), Cyclooxygenase-2 (COX-2), Matrixmetallo proteinases (MMP) 2/9, Proliferating cell nuclear antigen (PCNA), and Extracellular signal-regulated kinase-2 (ERK-2) as confirmed by immunofluorescence. Further, Westernblot analysis of MMPs-2/9, ERK-2 and Protein kinase B (Akt) revealed increased expressions of these proteins in DMH-induced groups of rats. AST-treatment decreased the expressions of all these vital proteins, involved in colon carcinogenesis. The ability of AST to induce apoptosis in the colon of DMH-induced rats was confirmed by Annexin-V/PI staining in a confocal microscopy, DNA fragmentation analysis and expression of caspase-3 by Western blotting. In conclusion, astaxanthin exhibits anti-inflammatory and anti-cancer effects by inducing apoptosis in DMH-induced rat colon carcinogenesis by modulating the expressions of NFkB, COX-2, MMPs-2/9, Akt and ERK-2.

Polymorphic one-dimensional (N2H4)2ZnTe: soluble precursors for the formation of hexagonal or cubic zinc telluride.

PubMed

Mitzi, David B

2005-10-03

Two hydrazine zinc(II) telluride polymorphs, (N2H4)2ZnTe, have been isolated, using ambient-temperature solution-based techniques, and the crystal structures determined: alpha-(N2H4)2ZnTe (1) [P21, a = 7.2157(4) Angstroms, b = 11.5439(6) Angstroms, c = 7.3909(4) Angstroms, beta = 101.296(1) degrees, Z = 4] and beta-(N2H4)2ZnTe (2) [Pn, a = 8.1301(5) Angstroms, b = 6.9580(5) Angstroms, c = 10.7380(7) Angstroms, beta = 91.703(1) degrees, Z = 4]. The zinc atoms in 1 and 2 are tetrahedrally bonded to two terminal hydrazine molecules and two bridging tellurium atoms, leading to the formation of extended one-dimensional (1-D) zinc telluride chains, with different chain conformations and packings distinguishing the two polymorphs. Thermal decomposition of (N2H4)2ZnTe first yields crystalline wurtzite (hexagonal) ZnTe at temperatures as low as 200 degrees C, followed by the more stable zinc blende (cubic) form at temperatures above 350 degrees C. The 1-D polymorphs are soluble in hydrazine and can be used as convenient precursors for the low-temperature solution processing of p-type ZnTe semiconducting films.

21 CFR 172.824 - Sodium mono- and dimethyl naphthalene sulfonates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Multipurpose Additives § 172.824 Sodium mono- and dimethyl naphthalene sulfonates. The food additive sodium mono- and dimethyl naphthalene sulfonates may be safely used in...

Divergent Mechanistic Routes for the Formation of gem-Dimethyl Groups in the Biosynthesis of Complex Polyketides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poust, S; Phelan, RM; Deng, K

The gem-dimethyl groups in polyketide-derived natural products add steric bulk and, accordingly, lend increased stability to medicinal compounds, however, our ability to rationally incorporate this functional group in modified natural products is limited. In order to characterize the mechanism of gem-dimethyl group formation, with a goal toward engineering of novel compounds containing this moiety, the gem-dimethyl group producing polyketide synthase (PKS) modules of yersiniabactin and epothilone were characterized using mass spectrometry. The work demonstrated, contrary to the canonical understanding of reaction order in PKSs, that methylation can precede condensation in gem-dimethyl group producing PKS modules. Experiments showed that both PKSsmore » are able to use dimethylmalonyl acyl carrier protein (ACP) as an extender unit. Interestingly, for epothilone module8, use of dimethylmalonyl-ACP appeared to be the sole route to form a gem-dimethylated product, while the yersiniabactin PKS could methylate before or after ketosynthase condensation.« less

1,2-Bis(methylsulfonyl)-1-(2-chloroethyl)-2-[[1-(4-nitrophenyl)ethoxy]carbonyl]hydrazine: An anticancer agent targeting hypoxic cells

PubMed Central

Seow, Helen A.; Penketh, Philip G.; Shyam, Krishnamurthy; Rockwell, Sara; Sartorelli, Alan C.

2005-01-01

To target malignant cells residing in hypoxic regions of solid tumors, we have designed and synthesized prodrugs generating the cytotoxic alkylating species 1,2-bis(methylsulfonyl)-1-(2-chloroethyl)hydrazine (90CE) after bioreductive activation. We postulate that one of these agents, 1,2-bis(methylsulfonyl)-1-(2-chloroethyl)-2-[[1-(4-nitrophenyl)ethoxy]carbonyl]hydrazine (KS119), requires enzymatic nitro reduction to produce 90CE, whereas another agent, 1,2-bis(methylsulfonyl)-1-(2-chloroethyl)-2-[(4-nitrobenzyloxy)carbonyl]hydrazine (PNBC), can also be activated by nucleophilic attack by thiols such as glutathione (GSH)/GST. We demonstrated that these agents selectively kill hypoxic EMT6 mouse mammary carcinoma and CHO cells. In hypoxia, 50 μM KS119 produced 5 logs of kill of EMT6 cells without discernable cytotoxicity in air; similar effects were observed with CHO cells. PNBC was less efficacious against hypoxic tumor cells and also had some toxicity to aerobic cells, presumably because of GST/thiol activation, making PNBC less interesting as a selective hypoxic-cell cytotoxin. BALB/c mice with established EMT6 solid tumors were used to demonstrate that KS119 could reach and kill hypoxic cells in solid tumors. To gain information on bioreductive enzymes involved in the activation of KS119, cytotoxicity was measured in CHO cell lines overexpressing NADH:cytochrome b5 reductase (NBR), NADPH:cytochrome P450 reductase (NPR), or NAD(P)H: quinone oxidoreductase 1 (NQO1). Increased cytotoxicity occurred in cells overexpressing NBR and NPR, whereas overexpressed NQO1 had no effect. These findings were supported by enzymatic studies using purified NPR and xanthine oxidase to activate KS119. KS119 has significant potential as a hypoxia-selective tumor-cell cytotoxin and is unlikely to cause major toxicity to well oxygenated normal tissues. PMID:15964988

Generation of semicarbazide from natural azine development in foods, followed by reaction with urea compounds.

PubMed

Abernethy, Grant A

2015-01-01

This paper proposes a mechanism to explain the trace levels of natural semicarbazide occasionally observed in foods. The analytical derivative of semicarbazide, 2-nitrobenzaldehyde semicarbazone, is often measured as a metabolite marker to detect the widely banned antibiotic nitrofurazone. However, this marker is not specific as semicarbazide may be present in foods for several reasons other than exposure to nitrofurazone. In some cases, an entirely natural origin of semicarbazide is suspected, although up until now there was no explanation about how semicarbazide could occur naturally. In this work, semicarbazide is proposed as being generated from natural food compounds via an azine intermediate. Hydrazine, in the form of azines or hydrazones, may be generated in dilute aqueous solution from the natural food compounds ammonia, hydrogen peroxide and acetone, following known oxidation chemistry. When this mixture was prepared in the presence of ureas such as allantoin, urea, biuret or hydroxyurea, and then analysed by the standard method for the determination of semicarbazide, 2-nitrobenzaldehyde semicarbazone was detected. 2-Nitrobenzaldehyde aldazine was also found, and it may be a general marker for azines in foods. This proposal, that azine formation is central to semicarbazide development, provides a convergence of the published mechanisms for semicarbazide. The reaction starts with hydrogen peroxide, peracetic acid, atmospheric oxygen or hypochlorite; generates hydrazine either by an oxaziridine intermediate or via the chlorination of ammonia; and then either route may converge on azine formation, followed by reaction with a urea compound. Additionally, carbamate ion may speculatively generate semicarbazide by reaction with hydrazine, which might be a significant route in the case of the hypochlorite treatment of foods or food contact surfaces. Significantly, detection of 2-nitrobenzaldehyde semicarbazone may be somewhat artefactual because semicarbazide can form during the acid conditions of analysis, which can free hydrazine in the presence of urea compounds.

Micro-kinetic simulations of the catalytic decomposition of hydrazine on the Cu(111) surface.

PubMed

Tafreshi, Saeedeh S; Roldan, Alberto; de Leeuw, Nora H

2017-04-28

Hydrazine (N 2 H 4 ) is produced at industrial scale from the partial oxidation of ammonia or urea. The hydrogen content (12.5 wt%) and price of hydrazine make it a good source of hydrogen fuel, which is also easily transportable in the hydrate form, thus enabling the production of H 2 in situ. N 2 H 4 is currently used as a monopropellant thruster to control and adjust the orbits and altitudes of spacecrafts and satellites; with similar procedures applicable in new carbon-free technologies for power generators, e.g. proton-exchange membrane fuel cells. The N 2 H 4 decomposition is usually catalysed by the expensive Ir/Al 2 O 3 material, but a more affordable catalyst is needed to scale-up the process whilst retaining reaction control. Using a complementary range of computational tools, including newly developed micro-kinetic simulations, we have derived and analysed the N 2 H 4 decomposition mechanism on the Cu(111) surface, where the energetic terms of all states have been corrected by entropic terms. The simulated temperature-programmed reactions have shown how the pre-adsorbed N 2 H 4 coverage and heating rate affect the evolution of products, including NH 3 , N 2 and H 2 . The batch reactor simulations have revealed that for the scenario of an ideal Cu terrace, a slow but constant production of H 2 occurs, 5.4% at a temperature of 350 K, while the discharged NH 3 can be recycled into N 2 H 4 . These results show that Cu(111) is not suitable for hydrogen production from hydrazine. However, real catalysts are multi-faceted and present defects, where previous work has shown a more favourable N 2 H 4 decomposition mechanism, and, perhaps, the decomposition of NH 3 improves the production of hydrogen. As such, further investigation is needed to develop a general picture.

40 CFR 180.229 - Fluometuron; tolerances for residues.

Code of Federal Regulations, 2014 CFR

2014-07-01

... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

40 CFR 180.229 - Fluometuron; tolerances for residues.

Code of Federal Regulations, 2012 CFR

2012-07-01

... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

40 CFR 180.229 - Fluometuron; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

40 CFR 180.229 - Fluometuron; tolerances for residues.

Code of Federal Regulations, 2011 CFR

2011-07-01

... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

40 CFR 180.229 - Fluometuron; tolerances for residues.

Code of Federal Regulations, 2013 CFR

2013-07-01

... combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl)phenyl]urea, and its... established for the combined residues of the herbicide fluometuron, N,N-dimethyl-N'-[3-(trifluoromethyl)phenyl... established for the combined residues of the herbicide fluometuron, N, N-dimethyl-N'-[3-(trifluoromethyl...

40 CFR 464.21 - Specialized definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 67. butyl benzyl phthalate 68. di-n-butyl phthalate 70. diethyl phthalate 71. dimethyl phthalate 72... 67. butyl benzyl phthalate 68. di-n-butyl phthalate 70. diethyl phthalate 71. dimethyl phthalate 72...-ethylhexyl) phthalate 67. butyl benzyl phthalate 68. di-n-butyl phthalate 70. diethyl phthalate 71. dimethyl...

40 CFR 464.21 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 67. butyl benzyl phthalate 68. di-n-butyl phthalate 70. diethyl phthalate 71. dimethyl phthalate 72... 67. butyl benzyl phthalate 68. di-n-butyl phthalate 70. diethyl phthalate 71. dimethyl phthalate 72...-ethylhexyl) phthalate 67. butyl benzyl phthalate 68. di-n-butyl phthalate 70. diethyl phthalate 71. dimethyl...

Alternative Fuels Data Center: Dimethyl Ether

Science.gov Websites

Hydrocarbon Biofuels Dimethyl Ether Dimethyl ether (DME) is a synthetically produced alternative to diesel for use in specially designed compression ignition diesel engines. Under normal atmospheric conditions ether has several fuel properties that make it attractive for use in diesel engines. It has a very high

Models for liquid-liquid partition in the system dimethyl sulfoxide-organic solvent and their use for estimating descriptors for organic compounds.

PubMed

Karunasekara, Thushara; Poole, Colin F

2011-07-15

Partition coefficients for varied compounds were determined for the organic solvent-dimethyl sulfoxide biphasic partition system where the organic solvent is n-heptane or isopentyl ether. These partition coefficient databases are analyzed using the solvation parameter model facilitating a quantitative comparison of the dimethyl sulfoxide-based partition systems with other totally organic partition systems. Dimethyl sulfoxide is a moderately cohesive solvent, reasonably dipolar/polarizable and strongly hydrogen-bond basic. Although generally considered to be non-hydrogen-bond acidic, analysis of the partition coefficient database strongly supports reclassification as a weak hydrogen-bond acid in agreement with recent literature. The system constants for the n-heptane-dimethyl sulfoxide biphasic system provide an explanation of the mechanism for the selective isolation of polycyclic aromatic compounds from mixtures containing low-polarity hydrocarbons based on the capability of the polar interactions (dipolarity/polarizability and hydrogen-bonding) to overcome the opposing cohesive forces in dimethyl sulfoxide that are absent for the interactions with hydrocarbons of low polarity. In addition, dimethyl sulfoxide-organic solvent systems afford a complementary approach to other totally organic biphasic partition systems for descriptor measurements of compounds virtually insoluble in water. Copyright © 2011 Elsevier B.V. All rights reserved.

Hydrogenation of liquid natural rubber via diimide reduction in hydrazine hydrate/hydrogen peroxide system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yusof, Muhammad Jefri Mohd; Jamaluddin, Naharullah; Abdullah, Ibrahim

Liquid natural rubber (LNR) with molecular weight of lower than 10{sup 5} and shorter polymeric chain than natural rubber was prepared. LNR was then hydrogenated via diimide reduction by oxidation of hydrazine hydrate with hydrogen peroxide. The unsaturated units of the rubber were converted into saturated hydrocarbon to strengthen the backbone of the polymer so it was able to resist thermal degradation. The results indicated that hydrogenation degree of the product (HLNR) could be extended to 91.2% conversion under appropriate conditions. The hydrogenated LNR (HLNR) was characterized using Fourier-Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. The physical characteristicsmore » of HLNR were analyzed with Termogravimetric Analysis (TGA)« less

Long term exposure of metals to hydrazine nitrate blend

NASA Technical Reports Server (NTRS)

Moran, Clifford M.; Blue, Gary D.

1986-01-01

A long term testing program is being conducted to determine the effects of materials in contact with a hydrazine nitrate blend for the purpose of designing chemical propulsion systems which can be used for current as well as future planetary spacecraft. Analysis of this data indicates that some aluminum alloys are acceptable for use with the particular blend of fuel used. Titanium alloy was identified as being acceptable for 10-year applications. Corrosion resistant steels, however, were found to have excessive corrosion rates and are therefore considered unacceptable for long-term use. There is also some evidence that the propellant decomposed at a rate far in excess of the acceptable rate of 0.1 percent per year when in contact with stainless steel.

Recommended Figures of Merit for Green Monopropellants

NASA Technical Reports Server (NTRS)

Marshall. William M.; Deans, Matthew C.

2013-01-01

Hydrazine propellant has historically been used as a rocket thruster monopropellant since the mid-1960s. Mission managers are well aware of its characteristics and performance. However, it is a known toxic chemical and a wide effort is underway to reduce and/or eliminate its use worldwide. Several new propellant combinations have been developed in the last few years which tout or promise to provide same or better performance as hydrazine while being "non-toxic" or "green". Yet, there is no consistent definition for what constitutes "non-toxic" or "green", and thus no good figure of merit for which to compare. This paper seeks to review the three major categories of figures of merit, and discusses how they might be used to assess the viability of a propellant.

The influence of different modified graphene on property of DSSCs

NASA Astrophysics Data System (ADS)

Xu, Kai; Shen, Yue; Zhang, Zongkun; Cao, Meng; Gu, Feng; Wang, Linjun

2016-01-01

Two kinds of modified reduced graphene oxide (rGO) power with different hydrophilic property were synthesized in NH3/hydrazine hydrate (N-rGO) and KOH/hydrazine hydrate (K-rGO) reduction systems, respectively, and be used as counter electrode materials. The as-prepared rGO counter electrodes were confirmed as substitution for Pt counter electrode in dye-sensitized solar cells (DSSCs). The efficiency (η) of DSSCs based on N-rGO counter electrodes achieved 4.72% while that of K-rGO counter electrode was just 3.38%. The electrochemical impedance spectroscopy (EIS) measurements revealed that the hydrophilic K-rGO counter electrode has a low charge transfer resistance (Rct) and the hydrophobic N-rGO counter electrode has a low series resistance (Rs).

Effect of group electronegativity on electron transfer in bis(hydrazine) radical cations.

PubMed

Qin, Haimei; Zhong, Xinxin; Si, Yubing; Zhang, Weiwei; Zhao, Yi

2011-04-14

The radical cation of 4,10-ditert-butyl-5,9-diisopropyl-4,5,9,10-tetraazatetracyclo[6.2.2.2]-tetradecane (sBI4T(+)), as well as its substituted bis(hydrazine) radical cations, is chosen for the investigation of the electronegativity dependence of its intramolecular electron transfer. To do so, two parameters, reorganization energy and electronic coupling, are calculated with several ab initio approaches. It is found that the electronic couplings decrease with the increase of the group electronegativity while the reorganization energies do not show an explicit dependency. Furthermore, Marcus formula is employed to reveal those effect on the electron transfer rates. The predicted rates of electron transfer generally decrease with increasing group electronegativity, although not monotonically.

Monolayer of Hydrazine Facilitates the Direct Covalent Attachment of C60 Fullerene to a Silicon Surface.

PubMed

Gao, Fei; Teplyakov, Andrew V

2017-09-05

The development of oxygen-free organic-inorganic interfaces has led to new schemes for the functionalization of silicon surfaces with nitrogen-based chemical groups. However, building layers of large structures directly on this functionalized surface has remained elusive. This work confirms the path to form a stable interface between silicon and buckminsterfullerene C 60 based on covalent chemical bonds. The starting point for this modification is the hydrazine-reacted Si(111) surface with the diamine functionality, which is further reacted directly with the C 60 molecules. The chemistry of this process is confirmed spectroscopically and microscopically and can be used to form organic-inorganic interfaces separated by a single layer of nitrogen.

Attitude analysis of the Earth Radiation Budget Satellite (ERBS) yaw turn anomaly

NASA Technical Reports Server (NTRS)

Kronenwetter, J.; Phenneger, M.; Weaver, William L.

1988-01-01

The July 2 Earth Radiation Budget Satellite (ERBS) hydrazine thruster-controlled yaw inversion maneuver resulted in a 2.1 deg/sec attitude spin. This mode continued for 150 minutes until the spacecraft was inertially despun using the hydrazine thrusters. The spacecraft remained in a low-rate Y-axis spin of .06 deg/sec for 3 hours until the B-DOT control mode was activated. After 5 hours in this mode, the spacecraft Y-axis was aligned to the orbit normal, and the spacecraft was commanded to the mission mode of attitude control. This work presents the experience of real-time attitude determination support following analysis using the playback telemetry tape recorded for 7 hours from the start of the attitude control anomaly.

40 CFR 180.296 - Dimethyl phosphate of 3-hydroxy-N-methyl-cis-crotonamide; tolerances for residues.

Code of Federal Regulations, 2010 CFR

2010-07-01

...-methyl-cis-crotonamide; tolerances for residues. 180.296 Section 180.296 Protection of Environment... RESIDUES IN FOOD Specific Tolerances § 180.296 Dimethyl phosphate of 3-hydroxy-N-methyl-cis-crotonamide; tolerances for residues. (a) General. Tolerances are established for residues of the insecticide Dimethyl...

21 CFR 73.37 - Astaxanthin dimethyl-disuccinate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Astaxanthin dimethyl-disuccinate. 73.37 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.37 Astaxanthin dimethyl-disuccinate. (a) Identity. (1) The color additive astaxanthin dimethyldisuccinate is 3,3′-bis(4-methoxy-1,4-dioxobutoxy)-β,β...

21 CFR 73.37 - Astaxanthin dimethyl-disuccinate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Astaxanthin dimethyl-disuccinate. 73.37 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.37 Astaxanthin dimethyl-disuccinate. (a) Identity. (1) The color additive astaxanthin dimethyldisuccinate is 3,3′-bis(4-methoxy-1,4-dioxobutoxy)-β,β...

21 CFR 73.37 - Astaxanthin dimethyl-disuccinate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 1 2014-04-01 2014-04-01 false Astaxanthin dimethyl-disuccinate. 73.37 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.37 Astaxanthin dimethyl-disuccinate. (a) Identity. (1) The color additive astaxanthin dimethyldisuccinate is 3,3′-bis(4-methoxy-1,4-dioxobutoxy)-β,β...

21 CFR 73.37 - Astaxanthin dimethyl-disuccinate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 1 2013-04-01 2013-04-01 false Astaxanthin dimethyl-disuccinate. 73.37 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.37 Astaxanthin dimethyl-disuccinate. (a) Identity. (1) The color additive astaxanthin dimethyldisuccinate is 3,3′-bis(4-methoxy-1,4-dioxobutoxy)-β,β...

21 CFR 73.37 - Astaxanthin dimethyl-disuccinate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 1 2012-04-01 2012-04-01 false Astaxanthin dimethyl-disuccinate. 73.37 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Foods § 73.37 Astaxanthin dimethyl-disuccinate. (a) Identity. (1) The color additive astaxanthin dimethyldisuccinate is 3,3′-bis(4-methoxy-1,4-dioxobutoxy)-β,β...

CARCINOGENIC EVALUATION OF 2,3-DIMETHYL-2,3-DINITROBUTANE VIA THE MOUSE SKIN BIOASSAY

EPA Science Inventory

Female SENCAR mice initiated with 2,3-dimethyl-2,3dimethyl-2,3-dinitrobutane (DMDNB) and promoted with 12-0-tetradecanoylphorol-13-acetate (TPA) via the SENCAR mouse skin bioassy did not exhibit a significant increase in skin tumors. The mice received 20 mg kg-1 DMDNE divided int...

DEVELOPMENTAL NEUOTOXICITY EVALUATION OF MIXTURES OF MONO- AND DIMETHYL TIN IN DRINKING WATER OF RATS.

EPA Science Inventory

Developmental Neurotoxicity Evaluation of Mixtures of Mono- and Dimethyl Tin in Drinking Water of Rats

V.C. Moser, K.L. McDaniel, P.M. Phillips

Neurotoxicology Division, NHEERL, ORD, US EPA, RTP, NC, USA

Organotins, especially monomethyl (MMT) and dimethyl (D...

Modeling of a Reaction-Distillation-Recycle System to Produce Dimethyl Ether through Methanol Dehydration

NASA Astrophysics Data System (ADS)

Muharam, Y.; Zulkarnain, L. M.; Wirya, A. S.

2018-03-01

The increase in the dimethyl ether yield through methanol dehydration due to a recycle integration to a reaction-distillation system was studied in this research. A one-dimensional phenomenological model of a methanol dehydration reactor and a shortcut model of distillation columns were used to achieve the aim. Simulation results show that 10.7 moles/s of dimethyl ether is produced in a reaction-distillation system with the reactor length being 4 m, the reactor inlet pressure being 18 atm, the reactor inlet temperature being 533 K, the reactor inlet velocity being 0.408 m/s, and the distillation pressure being 8 atm. The methanol conversion is 90% and the dimethyl ether yield is 48%. The integration of the recycle stream to the system increases the dimethyl ether yield by 8%.

2,3-Dimethyl-5-(2-methylpropyl)pyrazine, a trail pheromone component of Eutetramorium mocquerysi Emery (1899) (Hymenoptera: Formicidae)

NASA Astrophysics Data System (ADS)

Tentschert, J.; Bestmann, H.-J.; Hölldobler, B.; Heinze, J.

The ant Eutetramorium mocquerysi (Myrmicinae) is endemic to the island of Madagascar. During foraging and nest emigration the ants lay recruitment trails with secretions from the poison gland. We identified three pyrazine compounds in the poison gland secretion: 2,3-dimethyl-5-(2-methylpropyl)pyrazine 1, 2,3-dimethyl-5-(3-methylbutyl)pyrazine 3, 2,3-dimethyl-5-(2-methylbutyl)pyrazine 4. Only the first component elicited trail-following behavior in the ants. We were unable to investigate whether the other pyrazine components have a synergistic function.

Arginine (Di)methylated Human Leukocyte Antigen Class I Peptides Are Favorably Presented by HLA-B*07.

PubMed

Marino, Fabio; Mommen, Geert P M; Jeko, Anita; Meiring, Hugo D; van Gaans-van den Brink, Jacqueline A M; Scheltema, Richard A; van Els, Cécile A C M; Heck, Albert J R

2017-01-06

Alterations in protein post-translational modification (PTM) are recognized hallmarks of diseases. These modifications potentially provide a unique source of disease-related human leukocyte antigen (HLA) class I-presented peptides that can elicit specific immune responses. While phosphorylated HLA peptides have already received attention, arginine methylated HLA class I peptide presentation has not been characterized in detail. In a human B-cell line we detected 149 HLA class I peptides harboring mono- and/or dimethylated arginine residues by mass spectrometry. A striking preference was observed in the presentation of arginine (di)methylated peptides for HLA-B*07 molecules, likely because the binding motifs of this allele resemble consensus sequences recognized by arginine methyl-transferases. Moreover, HLA-B*07-bound peptides preferentially harbored dimethylated groups at the P3 position, thus consecutively to the proline anchor residue. Such a proline-arginine sequence has been associated with the arginine methyl-transferases CARM1 and PRMT5. Making use of the specific neutral losses in fragmentation spectra, we found most of the peptides to be asymmetrically dimethylated, most likely by CARM1. These data expand our knowledge of the processing and presentation of arginine (di)methylated HLA class I peptides and demonstrate that these types of modified peptides can be presented for recognition by T-cells. HLA class I peptides with mono- and dimethylated arginine residues may therefore offer a novel target for immunotherapy.

Process for producing dimethyl ether from synthesis gas

DOEpatents

Pierantozzi, R.

1985-06-04

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Two Approaches to the Synthesis of Dimethyl Fumarate That Demonstrate Fundamental Principles of Organic Chemistry

ERIC Educational Resources Information Center

Love, Brian E.; Bennett, Lisa J.

2017-01-01

Two experiments are described which lead to the preparation of dimethyl fumarate, a compound currently used in the treatment of multiple sclerosis. Preparation of a compound with "real-world" applications is believed to increase student interest in the experiment. One experiment involves the isomerization of dimethyl maleate to the…

40 CFR 721.2222 - Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2...

Code of Federal Regulations, 2011 CFR

2011-07-01

.... with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. 721.2222 Section 721.2222... Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. (a... cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate (PMN...

40 CFR 721.2222 - Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2...

Code of Federal Regulations, 2014 CFR

2014-07-01

.... with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. 721.2222 Section 721.2222... Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. (a... cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate (PMN...

40 CFR 721.2222 - Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2...

Code of Federal Regulations, 2012 CFR

2012-07-01

.... with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. 721.2222 Section 721.2222... Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. (a... cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate (PMN...

40 CFR 721.2222 - Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2...

Code of Federal Regulations, 2013 CFR

2013-07-01

.... with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. 721.2222 Section 721.2222... Cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate. (a... cyclohexanamine, N,N-dimethyl-, compd. with alpha-isotridecyl-omega-hydroxypoly(oxy-1,2-ethanediyl) phosphate (PMN...

Process for producing dimethyl ether form synthesis gas

DOEpatents

Pierantozzi, Ronald

1985-01-01

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

Determination of 2-alkylcyclobutanones by combining precolumn derivatization with 1-naphthalenyl hydrazine and ultra-performance liquid chromatography with fluorescence detection.

PubMed

Meng, Xiangpeng; Tong, Tong; Wang, Lianrong; Liu, Hanxia; Chan, Wan

2016-05-01

2-Alkylcyclobutanones (2-ACBs) are uniquely formed when triglycerides-containing food products are exposed to ionizing radiation. Thus, 2-ACBs have been used as marker molecules to identify irradiated food. Most methods to determine 2-ACBs involve mass spectrometric detection after chromatographic separation. The spectrofluorometer is rarely used to determine 2-ACBs because these molecules do not fluoresce. In this study, we developed an ultra-performance liquid chromatography (UPLC) method to determine 2-ACBs. 2-ACBs were converted into fluorophores after reacting with 1-naphthalenyl hydrazine to facilitate their sensitive and selective detection using a fluorescence detector (FLD). Analysis of 2-ACBs using our developed UPLC-FLD method allows sensitive determination of 2-ACBs at a detection limit of 2 ng 2-ACBs per g of fat (30 pg/injection), which is significantly lower than that of existing analytical methods. After validation for trueness and precision, the method was applied to γ-irradiated chicken samples to determine their 2-ACB content. Comparative studies employing liquid chromatography-tandem mass spectrometric method revealed no systematic difference between the two methods, thereby demonstrating that the proposed UPLC-FLD method can be suitably used to determine 2-ACBs in irradiated foodstuffs. Graphical Abstract Determination of radiation-induced food-borne 2-dodecylcyclobutanone and 2-tetradecylcyclobutanone by combining 1-naphthalenyl hydrazine derivatization and ultra-performance liquid chromatography with fluorescence detection.

Alkaline deoxygenated graphene oxide for supercapacitor applications: An effective green alternative for chemically reduced graphene

NASA Astrophysics Data System (ADS)

Perera, Sanjaya D.; Mariano, Ruperto G.; Nijem, Nour; Chabal, Yves; Ferraris, John P.; Balkus, Kenneth J.

2012-10-01

Graphene is a promising electrode material for energy storage applications. The most successful method for preparing graphene from graphite involves the oxidation of graphite to graphene oxide (GO) and reduction back to graphene. Even though different chemical and thermal methods have been developed to reduce GO to graphene, the use of less toxic materials to generate graphene still remains a challenge. In this study we developed a facile one-pot synthesis of deoxygenated graphene (hGO) via alkaline hydrothermal process, which exhibits similar properties to the graphene obtained via hydrazine reduction (i.e. the same degree of deoxygenation found in hydrazine reduced GO). Moreover, the hGO formed freestanding, binder-free paper electrodes for supercapacitors. Coin cell type (CR2032) symmetric supercapacitors were assembled using the hGO electrodes. Electrochemical characterization of hGO was carried out using lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and ethylmethylimidazolium bis-(trifluoromethanesulfonyl)imide (EMITFSI) electrolytes. The results for the hGO electrodes were compared with the hydrazine reduced GO (rGO) electrode. The hGO electrode exhibits a energy density of 20 W h kg-1 and 50 W h kg-1 in LiTFSI and EMITFSI respectively, while delivering a maximum power density of 11 kW kg-1 and 14.7 kW kg-1 in LiTFSI and EMITFSI, respectively.

40 CFR 721.4280 - Substituted hydrazine.

Code of Federal Regulations, 2010 CFR

2010-07-01

...). (ii) Hazard communication program. Requirements as specified in § 721.72 (a), (b), (c), (d), (e...)(5). In addition, the human health hazard statement shall include mutagenicity. (iii) Industrial...

Crystal structures of hibiscus acid and hibiscus acid dimethyl ester isolated from Hibiscus sabdariffa (Malvaceae).

PubMed

Zheoat, Ahmed M; Gray, Alexander I; Igoli, John O; Kennedy, Alan R; Ferro, Valerie A

2017-09-01

The biologically active title compounds have been isolated from Hibiscus sabdariffa plants, hibiscus acid as a dimethyl sulfoxide monosolvate [systematic name: (2 S ,3 R )-3-hy-droxy-5-oxo-2,3,4,5-tetra-hydro-furan-2,3-di-carb-oxy-lic acid dimethyl sulfoxide monosolvate], C 6 H 6 O 7 ·C 2 H 6 OS, (I), and hibiscus acid dimethyl ester [systematic name: dimethyl (2 S ,3 R )-3-hy-droxy-5-oxo-2,3,4,5-tetra-hydro-furan-2,3-di-carboxyl-ate], C 8 H 10 O 7 , (II). Compound (I) forms a layered structure with alternating layers of lactone and solvent mol-ecules, that include a two-dimensional hydrogen-bonding construct. Compound (II) has two crystallographically independent and conformationally similar mol-ecules per asymmetric unit and forms a one-dimensional hydrogen-bonding construct. The known absolute configuration for both compounds has been confirmed.

Biosynthesis of glycerol carbonate from glycerol by lipase in dimethyl carbonate as the solvent.

PubMed

Lee, Kyung Hwa; Park, Chang-Ho; Lee, Eun Yeol

2010-11-01

Glycerol carbonate was synthesized from renewable glycerol and dimethyl carbonate using lipase in solvent-free reaction system in which excess dimethyl carbonate played as the reaction medium. A variety of lipases have been tested for their abilities to catalyze transesterification reaction, and Candida antartica lipase B and Novozyme 435 exhibited higher catalytic activities. The silica-coated glycerol with a 1:1 ratio was supplied to prevent two-phase formation between hydrophobic dimethyl carbonate and hydrophilic glycerol. Glycerol carbonate was successfully synthesized with more than 90% conversion from dimethyl carbonate and glycerol with a molar ratio of 10 using Novozyme 435-catalyzed transesterification at 70 °C. The Novozyme 435 [5% (w/w) and 20% (w/w)] and silica gel were more than four times recycled with good stability in a repeated batch operation for the solvent-free synthesis of glycerol carbonate.

Determining resin/fiber content of laminates

NASA Technical Reports Server (NTRS)

Garrard, G. G.; Houston, D. W.

1979-01-01

Article discusses procedure where hydrazine is used to extract graphite fibers from cured polyimide resin. Method does not attack graphite fibers and is faster than hot-concentrated-acid digestion process.

Chemical Agents

MedlinePlus

... E Ethylene glycol F Fentanyls and other opioids H Hydrazine Hydrofluoric acid (hydrogen fluoride) Hydrogen chloride Hydrogen ... M Mercury Methyl bromide Methyl isocyanate Mustard gas (H) (sulfur mustard) N Nicotine Nitrogen mustard (HN-1, ...

Prolinimines: N-Amino-l-Pro-methyl Ester (Hydrazine) Schiff Bases from a Fish Gastrointestinal Tract-Derived Fungus, Trichoderma sp. CMB-F563.

PubMed

Mohamed, Osama G; Khalil, Zeinab G; Capon, Robert J

2018-01-19

A rice cultivation of a fish gastrointestinal tract-derived fungus, Trichoderma sp. CMB-F563, yielded natural products incorporating a rare hydrazine moiety, embedded within a Schiff base. Structures inclusive of absolute configurations were assigned to prolinimines A-D (1-4) on the basis of detailed spectroscopic and C 3 Marfey's analysis, as well as biosynthetic considerations, biomimetic total synthesis, and chemical transformations. Of note, monomeric 1 proved to be acid labile and, during isolation, underwent quantitative transformation to dimeric 3 and trimeric 4. Prolinimines are only the second reported natural products incorporating an N-amino-Pro residue, the first to include l-Pro, the first to occur as Schiff bases, and the first to be isolated from a microorganism.

KSC-97pc402

NASA Image and Video Library

1997-03-06

Workers take off the protective covering on the propulsion module for the Cassini spacecraft after uncrating the module at KSC's Spacecraft Assembly and Encapsulation Facility-2 (SAEF-2). The extended journey of 6.7 years to Saturn and the 4-year mission for Cassini once it gets there will require the spacecraft to carry a large amount of propellant for inflight trajectory-correction maneuvers and attitude control, particularly during the science observations. The propulsion module has redundant 445-newton main engines that burn nitrogen tetraoxide and monomethyl-hydrazine for main propulsion and 16 smaller 1-newton engines that burn hydrazine to control attitude and to correct small deviations from the spacecraft flight path. Cassini will be launched on a Titan IVB/Centaur expendable launch vehicle. Liftoff is targeted for October 6 from Launch Complex 40, Cape Canaveral Air Station

NASA Developments in Personnel Protective Equipment

NASA Technical Reports Server (NTRS)

Graf, John

2015-01-01

NASA has some unique and challenging PPE needs: there are credible threats to air quality (fire, ammonia leak, hydrazine leak)that require a contingency breathing apparatus that operates for many hours - but there is not enough space or up-mass to provide supplied air tanks. We cannot use "Scott Air Tanks" commonly used by firefighters and other first responders. NASA has developed a respirator based emergency breathing device. It uses a "one size fits everybody in the astronaut corps" hooded mask with excellent chemical permeability and fire resistance properties, and a filtering respirator cartridge that protects the wearer from ammonia leaks, hydrazine leaks, or products of combustion. If you need a small, lightweight emergency breathing system that lasts longer than a supplied air system, we should meet and learn if NASA sponsored technology development can help.

Employing a hydrazine linked asymmetric double naphthalene hybrid for efficient naked eye detection of F-: Crystal structure with real application for F-

NASA Astrophysics Data System (ADS)

Bhattacharyya, Arghyadeep; Makhal, Subhash Chandra; Ghosh, Soumen; Guchhait, Nikhil

2018-06-01

An asymmetric hydrazide, (12E, 13E)-2-((naphthalen-1-yl) methylene)-1-(1-(2-hydroxynaphthalen-6-yl) ethylidene) hydrazine (abbreviated as AH) is synthesized and characterized by standard techniques and crystal structure of AH has been obtained. The naked eye detection of F- in aqueous acetonitrile (acetonitrile: water = 7:3/v:v) by AH has been investigated by UV-Visible titration and in presence of other anions, the limit of detection being 1.31 × 10-6(M). The mechanism of F- sensing has been explored by 1H NMR titration. AH undergoes hydrogen bonding with F- followed by deprotonation. The practical utility of AH has been explored by successful test kit response and color change in toothpaste solution.

High- and low-thrust propulsion systems for the space station

NASA Technical Reports Server (NTRS)

Jones, R. E.

1987-01-01

The purpose of the Advanced Development program was to investigate propulsion options for the space station. Two options were investigated in detail: a high-thrust system consisting of 25 to 50 lbf gaseous oxygen/hydrogen rockets, and a low-thrust system of 0.1 lbf multipropellant resistojets. An effort is also being conducted to determine the life capability of hydrazine-fueled thrusters. During the course of this program, studies clearly identified the benefits of utilizing waste water and other fluids as propellant sources. The results of the H/O thruster test programs are presented and the plan to determine the life of hydrazine thrusters is discussed. The background required to establish a long-life resistojet is presented and the first design model is shown in detail.

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...

40 CFR 721.10055 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. 721.10055 Section 721.10055 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-soya acyl derivs., inner salts. (a) Chemical substance and...

40 CFR 721.10174 - 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Propanaminium, 3-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts. 721.10174 Section 721.10174 Protection of...-amino-N-(carboxymethyl)-N,N-dimethyl-, N-peanut-oil acyl derivs., inner salts. (a) Chemical substance...

One-Pot Preparation of Dimethyl Isosorbide from d-Sorbitol via Dimethyl Carbonate Chemistry.

PubMed

Aricò, F; Aldoshin, A S; Tundo, P

2017-01-10

Direct synthesis of dimethyl isosorbide (DMI) from d-sorbitol via dimethyl carbonate (DMC) chemistry is herein first reported. High yield of DMI was achieved using the nitrogen superbase 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD) as catalyst and performing the reaction in a stainless steel autoclave by increasing the temperature from 90 to 200 °C. In this procedure, DMC features its full capacity acting in the different steps of the process as carboxymethylating, leaving-group (cyclization), and methylating agent; DMC is also employed as the reaction media. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Influence of some technological parameters on the formation of dimethyl sulfide, 2-mercaptoethanol, methionol, and dimethyl sulfone in port wines.

PubMed

Silva Ferreira, António César; Rodrigues, Paula; Hogg, Timothy; Guedes De Pinho, Paula

2003-01-29

Volatile sulfur compounds of 15 young port wines and 12 old port wines were determined. As there is a great difference in the pool of sulfur compounds between the two groups of wines, an experimental protocol was performed to determine which technological parameter (dissolved O(2), free SO(2) levels, pH, and time/temperature) was related with the formation/consumption of these compounds. Four sulfur compounds were selected for this purpose: dimethyl sulfide, 2-mercaptoethanol, dimethyl sulfone, and methionol. The synergistic effects of increasing temperature and O(2) at lower pH had the largest impact. Dimethyl sulfide was formed during the experimental period in the presence of O(2). Dimethyl sulfone had the same behavior. Methionol decreased significantly in the presence of O(2), but no methional was formed. 2-Mercaptoethanol, considered to be an important "off-flavor" in dry wines, also decreased during the experimental period (54 days) in the presence of O(2), and the respective disulfide was formed. These results corroborate the fact that old port wine (barrel aged) never develops "off-flavors" associated with the presence of methionol (cauliflower), 2-mercaptoethanol (rubber/burnt), or methional (cooked potato). In fact, temperature and oxygen are the major factors in the consumption of these molecules. However, some notes of "quince" and "metallic" can appear during port wine aging, and these can be associated with the presence of dimethyl sulfide.

Gold-copper bimetallic nanoparticles supported on nano P zeolite modified carbon paste electrode as an efficient electrocatalyst and sensitive sensor for determination of hydrazine.

PubMed

Amiripour, Fatemeh; Azizi, Seyed Naser; Ghasemi, Shahram

2018-06-01

In this report, a facile, efficient and low cost electrochemical sensor based on bimetallic Au-Cu nanoparticles supported on P nanozeolite modified carbon paste electrode (Au-Cu/NPZ/CPE) was constructed and its efficiency for determination of hydrazine in trace level was studied. For this purpose, agro waste material, stem sweep ash (SSA) was employed as the starting material (silica source) for the synthesis of nano P zeolite (NPZ). After characterization of the synthesized NPZ by analytical instruments (scanning electronic microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectroscopy), construction of Au-Cu/NPZ/CPE was performed by three steps procedure involving preparation of nano P zeolite modified carbon paste electrode (NPZ/CPE), introducing Cu +2 ions into nano zeolite structure by ion exchange and electrochemical reduction of Cu +2 ions upon applying constant potential. This procedure is followed by partial replacement of Cu by Au due to galvanic replacement reaction (GRR). The electrochemical properties of hydrazine at the surface of Au-Cu/NPZ/CPE was evaluated using cyclic voltammetry (CV), amperometry, and chronoamperometry methods in 0.1 M phosphate buffer solution (PBS). It was found that the prepared sensor has higher electrocatalytic activity at a relatively lower potential compared to other modified electrodes including Au/NPZ/CPE, Cu/NPZ/CPE, Au-Cu/CPE and etc. Moreover, the proposed electrochemical sensor presented the favorable analytical properties for determination of hydrazine such as low detection limit (0.04 µM), rapid response time (3 s), wide linear range (0.01-150 mM), and high sensitivity (99.53 µA mM -1 ) that are related to the synergic effect of bimetallic of Au-Cu, porous structure and enough surface area of NPZ. In addition, capability of Au-Cu/NPZ/CPE sensor was successfully tested in real samples with good accuracy and precision. Copyright © 2018 Elsevier B.V. All rights reserved.

Visible-light-induced two-electron-transfer photoreductions on CdS: Effects of morphology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shiragami, Tsutomu; Pac, Chyongjin; Yanagida, Shozo

1990-01-25

Freshly prepared CdS suspensions (CdS-O) consisting of quantized particles and their loose aggregation catalyze photoreductions of aromatic ketones and olefins in methanol under visible light irradiation using triethylamine as sacrificial electron donor, yielding alcohols and dihydro compounds, respectively, which are more selective than photocatalysis of commercially available crystalline CdS (Aldrich) (CdS-Ald). Deuterium incorporation experiments in photolysis of dimethyl maleate in methanol-O-D revealed that CdS-O catalyzes sequential two-electron-transfer photoreduction, affording dideuterated dimethyl succinate, while CdS-Ald induces both photoreduction and photoisomerization through disproportionation between one-electron-transfer-reduction intermediates, yielding much trideuterated dimethyl succinate and monodeuterated dimethyl fumarate and maleate.

Improving amphetamine therapeutic selectivity: N,N-dimethyl-MTA has dopaminergic effects and does not produce aortic contraction.

PubMed

Sotomayor-Zárate, Ramón; Jara, Pablo; Araos, Patricio; Vinet, Raúl; Quiroz, Gabriel; Renard, Georgina M; Espinosa, Pedro; Hurtado-Guzmán, Claudio; Moya, Pablo R; Iturriaga-Vásquez, Patricio; Gysling, Katia; Reyes-Parada, Miguel

2014-05-01

Amphetamine derivatives have therapeutic potential in diseases such as attention deficit hyperactivity disorder, narcolepsy and obesity. However, their prolonged use has been associated with cardiovascular toxicity and addiction. In recent years, we have studied the pharmacological effects of amphetamine derivatives such as methylthioamphetamine (MTA) and N,N-dimethyl-thioamphetamine, with the aim of improving their therapeutic selectivity. In this work, we show that similarly to MTA, N,N-dimethyl-thioamphetamine has effects on the dopamine system, producing a significant increase in extracellular levels of dopamine (as measured by in vivo brain microdialysis) and locomotor activity, which is a behavioural measure of dopaminergic activation. However, unlike MTA, N,N-dimethyl- thioamphetamine does not produce aortic contraction in vitro. Our results show that N,N-dimethyl-thioamphetamine is a drug that retains the dopaminergic effects of amphetamine derivatives but exhibits a lower potential for producing cardiovascular side effects. © 2013 Nordic Association for the Publication of BCPT (former Nordic Pharmacological Society).

Studies on volatile organic compounds of some truffles and false truffles.

PubMed

D'Auria, Maurizio; Racioppi, Rocco; Rana, Gian Luigi; Laurita, Alessandro

2014-01-01

Results of solid phase micro-extraction coupled to gas chromatography and mass spectrometry analyses, accomplished on sporophores of 11 species of truffles and false truffles, are reported. Volatile organic compounds (VOCs) found in Gautieria morchelliformis were dimethyl sulphide, 1,3-octadiene, 3,7-dimethyl-1,6-octadien-3-ol, amorphadiene, isoledene and cis-muurola-3,5-diene. In Hymenogaster luteus var. luteus, presence of 1,3-octadiene, 1-octen-3-ol, 3-octanone, 3-octanol and 4-acetylanisole was revealed. Two VOCs, 4-acetylanisole and β-farnesene, constituted aroma of Hymenogaster olivaceus.Melanogaster broomeanus exhibited as components of its aroma 2-methyl-1,3-butadiene, 2-methylpropanal, 2-methylpropanol, isobutyl acetate, 3,7-dimethyl-1,6-octadien-3-ol, 3-octanone and β-curcumene. VOC profile of Octavianina asterosperma was characterised by the presence of dimethyl sulphide, ethyl 2-methylpropanoate, methyl 2-methylbutanoate and 3-octanone. Tuber rufum var. rufum and Pachyphloeus conglomeratus showed the presence of dimethyl sulphide only.

Obligate methylotrophy: evaluation of dimethyl ether as a C1 compound.

PubMed Central

Meyers, A J

1982-01-01

The suitability of dimethyl ether as a C1 compound was examined with the obligate methylobacterium Methylococcus capsulatus (Texas). The ether did not support growth and was not formed during growth on methane; it was an inhibitor of growth and oxidation of methane and a poor oxidation substrate for cell suspensions. NADH stimulation of methane, but not dimethyl ether, oxidation occurred in cell extracts. PMID:6802804

75 FR 55327 - Tetrahydro-3,5-dimethyl-2H-1,3,5-thiadiazine-2-thione (Dazomet); Notice of Receipt of Request to...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-10

... is granted, any sale, distribution, or use of products listed in this notice will be permitted after...-3,5-dimethyl-2H-1,3,5-thiadiazine-2-thione product registrations to terminate or delete one or more... would not terminate the last tetrahydro-3,5-dimethyl-2H-1,3,5-thiadiazine-2- thione products registered...

N,N-dimethylsulfamide as precursor for N-nitrosodimethylamine (NDMA) formation upon ozonation and its fate during drinking water treatment.

PubMed

Schmidt, Carsten K; Brauch, Heinz-Jürgen

2008-09-01

Application and microbial degradation of the fungicide tolylfluanide gives rise to a new decomposition product named N,N-dimethylsulfamide (DMS). In Germany, DMS was found in groundwaters and surface waters with typical concentrations in the range of 100-1000 ng/L and 50-90 ng/L, respectively. Laboratory-scale and field investigations concerning its fate during drinking water treatment showed that DMS cannot be removed via riverbank filtration, activated carbon filtration, flocculation, and oxidation or disinfection procedures based on hydrogen peroxide, potassium permanganate, chlorine dioxide, or UV irradiation. Even nanofiltration does not provide a sufficient removal efficiency. During ozonation about 30-50% of DMS are converted to the carcinogenic N-nitrosodimethylamine (NDMA). The NDMA being formed is biodegradable and can at least partially be removed by subsequent biologically active drinking water treatment steps including sand or activated carbon filtration. Disinfection with hypochlorous acid converts DMS to so far unknown degradation products but not to NDMA or 1,1-dimethylhydrazine (UDMH).

Formation of NDMA and halogenated DBPs by chloramination of tertiary amines: the influence of bromide ion.

PubMed

Le Roux, Julien; Gallard, Hervé; Croué, Jean-Philippe

2012-02-07

The formation of NDMA and other DBPs (including THMs, HANs, and HKs) has been investigated by chloramination of several tertiary amines in the absence and presence of bromide ion. NDMA formation from the most reactive tertiary amines (e.g., dimethylaminomethylfurfuryl alcohol or DMP30) was enhanced in the presence of bromide due to the formation of brominated oxidant species such as bromochloramine (NHBrCl) and the hypothetical UDMH-Br as an intermediate. The formation of NDMA by chloramination of less reactive model compounds was inhibited in the presence of bromide. This can be explained by competitive reactions leading to the production of brominated DBPs (i.e., THMs). In the presence of bromide, the formation of brominated THMs during chloramination can be attributed to the presence of small amounts of HOBr produced by the decomposition of chloramines and bromamines. The results are of particular interest to understand NDMA formation mechanisms, especially during chloramination of wastewaters impacted by anthropogenic tertiary amines and containing bromide ion.

High-power CW laser using hydrogen-fluorine reaction

NASA Technical Reports Server (NTRS)

Moynihan, P. I.

1975-01-01

Continuous-wave laser has been proposed based on reaction of hydrogen and fluorine. Hydrogen is produced by dissociation of hydrazine, which can be stored as liquid in light containers at room temperature.

(E)-1-(2,4-Di-nitro-phen-yl)-2-(3-eth-oxy-4-hy-droxy-benzyl-idene)hydrazine.

PubMed

Fun, Hoong-Kun; Chantrapromma, Suchada; Ruanwas, Pumsak; Kobkeatthawin, Thawanrat; Chidan Kumar, C S

2014-01-01

The mol-ecule of the title hydrazine derivative, C15H14N4O6, is essentially planar, the dihedral angle between the substituted benzene rings being 2.25 (9)°. The eth-oxy and hy-droxy groups are almost coplanar with their bound benzene ring [r.m.s. deviation = 0.0153 (2) Å for the ten non-H atoms]. Intra-molecular N-H⋯O and O-H⋯Oeth-oxy hydrogen bonds generate S(6) and S(5) ring motifs, respectively. In the crystal, mol-ecules are linked by O-H⋯Onitro hydrogen bonds into chains propagating in [010]. Weak aromatic π-π inter-actions, with centroid-centroid distances of 3.8192 (19) and 4.0491 (19) Å, are also observed.

A lightweight pumped hydrazine orbit maneuvering space vehicle

NASA Astrophysics Data System (ADS)

Whitehead, J. C.

1992-01-01

An orbital maneuvering vehicle has a pair of opposed cylindrical piston tanks for hydrazine, and four transverse liquid rocket engines along a longitudinal plane. A new kind of pumped rocket propulsion provides maneuvering thrust on demand, and free-piston pumps which can rapidly start and stop are radially oriented between thrusters. A major advantage of this configuration is that the tanks can be close together, which maximizes the vehicle's longitudinal bending stiffness while minimizing the mass of the central bridging structure. The impulses from pump exhaust and piston reciprocation are directed through the system mass center, so they apply no disturbance torques. All high-temperature components are located on the outside of the central structure, where they are free to expand and radiate heat without detrimental effects. Virtually all lightweight components have been fabricated and tested, and photographs of hardware subassemblies are presented.

Performance of a Miniaturized Arcjet

NASA Technical Reports Server (NTRS)

Sankovic, John M.; Jacobson, David T.

1995-01-01

Performance measurements were obtained and life-limiting mechanisms were identified on a laboratory-model arcjet thruster designed to operate at a nominal power level of 300 W. The design employed a supersonic-arc-attachment concept and was operated from 200 to 400 W on hydrogen/nitrogen mixtures in ratios simulating fully decomposed hydrazine and ammonia. Power was provided by breadboard power processor. Performance was found to be a strong function of propellant flow rate. Anode losses were essentially constant for the range of mass flow rates tested. It is believed that the performance is dominated by viscous effects. Significantly improved performance was noted with simulated ammonia operation. At 300 W the specific impulse on simulated ammonia was 410 s with an efficiency of 0.34, while simulated hydrazine provided 370 s specific impulse at an efficiency of 0.27.

Synthesis and Structural Characterization of CdFe2O4 Nanostructures

NASA Astrophysics Data System (ADS)

Kalpanadevi, K.; Sinduja, C. R.; Manimekalai, R.

The synthesis of CdFe2O4 nanoparticles has been achieved by a simple thermal decomposition method from the inorganic precursor, [CdFe2(cin)3(N2H4)3], which was obtained by a simple precipitation method from the corresponding metal salts, cinnamic acid and hydrazine hydrate. The precursor was characterized by hydrazine and metal analyses, infrared spectral analysis and thermo gravimetric analysis. On appropriate annealing, [CdFe2(cin)3(N2H4)3] yielded CdFe2O4 nanoparticles. The XRD studies showed that the crystallite size of the particles was 13nm. The results of HRTEM studies also agreed well with those of XRD. SAED pattern of the sample established the polycrystalline nature of the nanoparticles. SEM images displayed a random distribution of grains in the sample.

Synthesis, structure, and thermal properties of soluble hydrazinium germanium(IV) and tin(IV) selenide salts.

PubMed

Mitzi, David B

2005-05-16

The crystal structures of two hydrazinium-based germanium(IV) and tin(IV) selenide salts are determined. (N(2)H(5))(4)Ge(2)Se(6) (1) [I4(1)cd, a = 12.708(1) Angstroms, c = 21.955(2) Angstroms, Z = 8] and (N(2)H(4))(3)(N(2)H(5))(4)Sn(2)Se(6) (2) [P, a = 6.6475(6) Angstroms, b = 9.5474(9) Angstroms, c = 9.8830(10) Angstroms, alpha = 94.110(2) degrees, beta = 99.429(2) degrees, gamma = 104.141(2) degrees, Z = 1] each consist of anionic dimers of edge-sharing metal selenide tetrahedra, M(2)Se(6)(4-) (M = Ge or Sn), separated by hydrazinium cations and, for 2, additional neutral hydrazine molecules. Substantial hydrogen bonding exists among the hydrazine/hydrazinium molecules as well as between the hydrazinium cations and the selenide anions. Whereas the previously reported tin(IV) sulfide system, (N(2)H(5))(4)Sn(2)S(6), decomposes cleanly to microcrystalline SnS(2) when heated to 200 degrees C in an inert atmosphere, higher temperatures (>300 degrees C) are required to dissociate selenium from 1 and 2 for the analogous preparations of single-phase metal selenides. The metal chalcogenide salts are highly soluble in hydrazine, as well as in a variety of amines and DMSO, highlighting the potential usefulness of these compounds as precursors for the solution deposition of the corresponding metal chalcogenide films.

A first-principles study on adsorption behaviors of pristine and Li-decorated graphene sheets toward hydrazine molecules

NASA Astrophysics Data System (ADS)

Zeng, Huadong; Cheng, Xinlu; Wang, Wei

2018-03-01

The adsorption behaviors and properties of hydrazine (N2H4) molecules on pristine and Li-decorated graphene sheets were investigated by means of first-principles based on density functional theory. We systematically analyzed the optimal geometry, average binding energy, charge transfer, charge density difference and density of states of N2H4 molecules adsorbed on pristine and Li-decorated graphene sheets. It is found that the interaction between single N2H4 molecule and pristine graphene is weak physisorption with the low binding energy of -0.026 eV, suggesting that the pristine graphene sheet is insensitive to the presence of N2H4 molecule. However, it is markedly enhanced after lithium decoration with the high binding energy of -1.004 eV, verifying that the Li-decorated graphene sheet is significantly sensitive to detect N2H4 molecule. Meanwhile, the effects of the concentrations of N2H4 molecules on two different substrates were studied detailedly. For pristine graphene substrate, the average binding energy augments apparently with increasing the number of N2H4 molecules, which is mainly attributed to the van der Waals interactions and hydrogen bonds among N2H4 clusters. Li-decorated graphene sheet has still a strong affinity to N2H4 molecules despite the corresponding average binding energy emerges a contrary tendency. Overall, Li-decorated graphene sheet could be considered as a potential gas sensor in field of hydrazine molecules.

Structural, optical, and electrical properties of PbSe nanocrystal solids treated thermally or with simple amines.

PubMed

Law, Matt; Luther, Joseph M; Song, Qing; Hughes, Barbara K; Perkins, Craig L; Nozik, Arthur J

2008-05-07

We describe the structural, optical, and electrical properties of films of spin-cast, oleate-capped PbSe nanocrystals that are treated thermally or chemically in solutions of hydrazine, methylamine, or pyridine to produce electronically coupled nanocrystal solids. Postdeposition heat treatments trigger nanocrystal sintering at approximately 200 degrees C, before a substantial fraction of the oleate capping group evaporates or pyrolyzes. The sintered nanocrystal films have a large hole density and are highly conductive. Most of the amine treatments preserve the size of the nanocrystals and remove much of the oleate, decreasing the separation between nanocrystals and yielding conductive films. X-ray scattering, X-ray photoelectron and optical spectroscopy, electron microscopy, and field-effect transistor electrical measurements are used to compare the impact of these chemical treatments. We find that the concentration of amines adsorbed to the NC films is very low in all cases. Treatments in hydrazine in acetonitrile remove only 2-7% of the oleate yet result in high-mobility n-type transistors. In contrast, ethanol-based hydrazine treatments remove 85-90% of the original oleate load. Treatments in pure ethanol strip 20% of the oleate and create conductive p-type transistors. Methylamine- and pyridine-treated films are also p-type. These chemically treated films oxidize rapidly in air to yield, after short air exposures, highly conductive p-type nanocrystal solids. Our results aid in the rational development of solar cells based on colloidal nanocrystal films.

Incorporation of alpha-Ketoglutaric Acid as a Fixed Bed Scrubber Media for the Neutralization of Hydrazine Family Hypergolic Fuels

NASA Technical Reports Server (NTRS)

DeVor, R. W.; Santiago-Maldonado, E.; Parkerson, J. K.

2010-01-01

A candidate scrubber media, alpha-ketoglutaric acid (aKGA) adsorbed onto a silica-based substrate was examined as a potential alternative to the hydrazine-family hypergolic fuel neutralization techniques currently utilized at NASA/Kennedy Space Center (KSC). Helvenson et. al. has indicated that aKGA will react with hydrazines to produce non-hazardous, possibly biodegradable products. Furthermore, the authors have previously tested and demonstrated the use of aKGA aqueous solutions as a replacement neutralizing agent for citric acid, which is currently used as a scrubbing agent in liquid scrubbers at KSC. Specific properties examined include reaction efficiency, the loading capacity of aKGA onto various silica substrates, and the comparison of aKGA media performance to that of the citric acid vapor scrubber systems at KSC and a commercial vapor scrubber media. Preliminary investigations showed hydrophobic aerogel particles to be an ideal substrate for the deposition of the aKGA. Current studies have shown that the laboratory produced aKGA-Aerogel absorbent media are more efficient and cost effective than a commercially available fixed bed scrubber media, although much less cost effective than liquid-based citric acid scrubbers (although possibly safer and less labor intensive). A comparison of all three alternative scrubber technologies (liquid aKGA, solid-phase aKGA, and commercially available sorbent materials) is given considering both hypergolic neutralization capabilities and relative costs (as compared to the current citric acid scrubbing technology in use at NASA/KSC).

Solar Electric and Chemical Propulsion Technology Applications to a Titan Orbiter/Lander Mission

NASA Technical Reports Server (NTRS)

Cupples, Michael

2007-01-01

Several advanced propulsion technology options were assessed for a conceptual Titan Orbiter/Lander mission. For convenience of presentation, the mission was broken into two phases: interplanetary and Titan capture. The interplanetary phase of the mission was evaluated for an advanced Solar Electric Propulsion System (SEPS), while the Titan capture phase was evaluated for state-of-art chemical propulsion (NTO/Hydrazine), three advanced chemical propulsion options (LOX/Hydrazine, Fluorine/Hydrazine, high Isp mono-propellant), and advanced tank technologies. Hence, this study was referred to as a SEPS/Chemical based option. The SEPS/Chemical study results were briefly compared to a 2002 NASA study that included two general propulsion options for the same conceptual mission: an all propulsive based mission and a SEPS/Aerocapture based mission. The SEP/Chemical study assumed identical science payload as the 2002 NASA study science payload. The SEPS/Chemical study results indicated that the Titan mission was feasible for a medium launch vehicle, an interplanetary transfer time of approximately 8 years, an advanced SEPS (30 kW), and current chemical engine technology (yet with advanced tanks) for the Titan capture. The 2002 NASA study showed the feasibility of the mission based on a somewhat smaller medium launch vehicle, an interplanetary transfer time of approximately 5.9 years, an advanced SEPS (24 kW), and advanced Aerocapture based propulsion technology for the Titan capture. Further comparisons and study results were presented for the advanced chemical and advanced tank technologies.

Expected and unexpected products of reactions of 2-hydrazinylbenzo-thia-zole with 3-nitro-benzene-sulfonyl chloride in different solvents.

PubMed

Morscher, Alexandra; de Souza, Marcus V N; Wardell, James L; Harrison, William T A

2018-05-01

The syntheses and crystal structures of 2-[2-(propan-2-yl-idene)hydrazin-yl]-1,3-benzo-thia-zol-3-ium 3-nitro-benzene-sulfonate (C 10 H 12 N 2 S + ·C 6 H 4 NO 5 S - ), (I), 2-[2-(3-nitro-benzene-sulfon-yl)hydrazin-yl]-1,3-benzo-thia-zole (C 13 H 10 N 4 O 4 S 2 ), (II) and 2-[2-(3-nitro-benzene-sulfon-yl)hydrazin-yl]-1,3-benzo-thia-zol-3-ium 3-nitro-benzene-sulfonate (C 13 H 11 N 4 O 4 S 2 + ·C 6 H 4 NO 5 S - ), (III) are reported. Salt (I) arose from an unexpected reaction of 2-hydrazinylbenzo-thia-zole with the acetone solvent in the presence of 3-nitro-benzene-sulfonyl chloride, whereas (II) and (III) were recovered from the equivalent reaction carried out in methanol. The crystal of (I) features ion pairs linked by pairs of N-H⋯O s (s = sulfonate) hydrogen bonds; adjacent cations inter-act by way of short π-π stacking inter-actions between the thia-zole rings [centroid-centroid separation = 3.4274 (18) Å]. In (II), which crystallizes with two neutral mol-ecules in the asymmetric unit, the mol-ecules are linked by N-H⋯N and N-H⋯O n (n = nitro) hydrogen bonds to generate [[Formula: see text]1[Formula: see text

Green reduction of graphene oxide by ascorbic acid

NASA Astrophysics Data System (ADS)

Khosroshahi, Zahra; Kharaziha, Mahshid; Karimzadeh, Fathallah; Allafchian, Alireza

2018-01-01

Graphene, a single layer of sp2-hybridized carbon atoms in a hexagonal (two-dimensional honey-comb) lattice, has attracted strong scientific and technological interest due to its novel and excellent optical, chemical, electrical, mechanical and thermal properties. The solution-processable chemical reduction of Graphene oxide (GO is considered as the most favorable method regarding mass production of graphene. Generally, the reduction of GO is carried out by chemical approaches using different reductants such as hydrazine and sodium borohydride. These components are corrosive, combustible and highly toxic which may be dangerous for personnel health and the environment. Hence, these reducing agents are not promising choice for reducing of graphene oxide (GO). As a consequence, it is necessary for further development and optimization of eco-friendly, natural reducing agent for clean and effective reduction of GO. Ascorbic acid, an eco-friendly and natural reducing agents, having a mild reductive ability and nontoxic property. So, the aim of this research was to green synthesis of GO with ascorbic acid. For this purpose, the required amount of NaOH and ascorbic acid were added to GO solution (0.5 mg/ml) and were heated at 95 °C for 1 hour. According to the X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and electrochemical results, GO were reduced with ascorbic acid like hydrazine with better electrochemical properties and ascorbic acid is an ideal substitute for hydrazine in the reduction of graphene oxide process.

40 CFR 721.10175 - 1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-(C12-18 and C18-unsatd...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1-Propanaminium, N-(3-aminopropyl)-2... 1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-(C12-18 and C18-unsatd. acyl... chemical substance identified as 1-Propanaminium, N-(3-aminopropyl)-2-hydroxy-N,N-dimethyl-3-sulfo-, N-(C12...

Phosphonate–Phosphinate Rearrangement

PubMed Central

2014-01-01

LiTMP metalated dimethyl N-Boc-phosphoramidates derived from 1-phenylethylamine and 1,2,3,4-tetrahydronaphthalen-1-ylamine highly selectively at the CH3O group to generate short-lived oxymethyllithiums. These isomerized to diastereomeric hydroxymethylphosphonamidates (phosphate–phosphonate rearrangement). However, s-BuLi converted the dimethyl N-Boc-phosphoramidate derived from 1-phenylethylamine to the N-Boc α-aminophosphonate preferentially. Only s-BuLi deprotonated dimethyl hydroxymethylphosphonamidates at the benzylic position and dimethyl N-Boc α-aminophosphonates at the CH3O group to induce phosphonate–phosphinate rearrangements. In the former case, the migration of the phosphorus substituent from the nitrogen to the carbon atom followed a retentive course with some racemization because of the involvement of a benzyllithium as an intermediate. PMID:25525945

Gas chromatographic--mass spectrometric quantitation of 16, 16-dimethyl-trans-delta 2-PGE1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dimov, V.; Green, K.; Bygdeman, M.

1983-02-01

Di-deuterated and di-tritiated 16,16-dimethyl-trans-delta 2-PGE1 has been synthesized and used for development of a GC-MS method for quantitation of corresponding unlabelled drug in patient plasma. Although these carrier/internal standard molecules only contain 2 deuterium atoms the lower limit of detection at each injection is as low as about 40 pg. The maximum plasma levels of this drug following administration of vaginal suppositories used in clinical studies (1 mg 16,16-dimethyl-trans-delta 2-PGE1 methyl ester in 0.8 g Witepsol S-52) were 100-350 pg/ml i.e. in the same order of magnitude as earlier seen for 16,16-dimethyl-PGE2.

The synthesis and structure of a potential immunosuppressant: N-mycophenoyl malonic acid dimethyl ester

NASA Astrophysics Data System (ADS)

Siebert, Agnieszka; Cholewiński, Grzegorz; Garwolińska, Dorota; Olejnik, Adrian; Rachoń, Janusz; Chojnacki, Jarosław

2018-01-01

The synthesis of a potential immunosuppressant, i.e. dimethyl ester of N-mycophenoyl malonic acid was optimized in the reaction of mycophenolic acid (MPA) with amino malonic dimethyl ester in the presence of propanephosphonic anhydride (T3P) as a coupling reagent. The structural properties of the obtained MPA derivative were investigated by NMR, MS and single crystal X-ray diffraction methods. Theoretical considerations of conformational flexibility based on DFT calculations are presented.

Evaluation of the binding interaction between bovine serum albumin and dimethyl fumarate, an anti-inflammatory drug by multispectroscopic methods

NASA Astrophysics Data System (ADS)

Jattinagoudar, Laxmi; Meti, Manjunath; Nandibewoor, Sharanappa; Chimatadar, Shivamurti

2016-03-01

The information of the quenching reaction of bovine serum albumin with dimethyl fumarate is obtained by multi-spectroscopic methods. The number of binding sites, n and binding constants, KA were determined at different temperatures. The effect of increasing temperature on Stern-Volmer quenching constants (KD) indicates that a dynamic quenching mechanism is involved in the interaction. The analysis of thermodynamic quantities namely, ∆H° and ∆S° suggested hydrophobic forces playing a major role in the interaction between dimethyl fumarate and bovine serum albumin. The binding site of dimethyl fumarate on bovine serum albumin was determined by displacement studies, using the site probes viz., warfarin, ibuprofen and digitoxin. The determination of magnitude of the distance of approach for molecular interactions between dimethyl fumarate and bovine serum albumin is calculated according to the theory of Förster energy transfer. The CD, 3D fluorescence spectra, synchronous fluorescence measurements and FT-IR spectral results were indicative of the change in secondary structure of the protein. The influence of some of the metal ions on the binding interaction was also studied.

Volatile sulphur compounds in UHT milk.

PubMed

Al-Attabi, Z; D'Arcy, B R; Deeth, H C

2009-01-01

Several volatile sulphur compounds have been detected in raw and processed milk. These are hydrogen sulphide, methanethiol, carbonyl sulphide, dimethyl sulphide, carbon disulphide, dimethyl disulphide, dimethyl trisulphide, dimethyl sulphoxide, and dimethyl sulphone. Many of these increase in milk during heat processing and are associated with the cooked flavor of heat-treated milks, particularly UHT and sterilized milk. Several researchers have attempted to explain the origin of these volatiles in both raw and processed milk, and how to reduce the associated cooked flavor that has a negative impact on consumer acceptability of processed milk. These compounds are difficult to detect and analyze due to their high volatility, sensitivity to oxidation and heat, and in some cases, their very low concentrations. However, methods of detection and quantification have improved in recent years. Pre-concentration methods such as solid phase microextraction (SPME) together with gas chromatography equipped with sulphur-selective detectors now enable low concentrations of these compounds to be analyzed. In this review, methods of extraction and analyzes of these volatile sulphur compounds are compared, and their occurrence in milk is reviewed.

Arc-Jet Thrustor Development

NASA Technical Reports Server (NTRS)

Curran, F. M.; Hamley, J. A.; Gruber, R. P.; Sankovic, J. M.; Haag, T. W.; Marren, W. E.; Sarmiento, C. J.; Carney, L.

1993-01-01

Two flight-type 1.4-kW hydrazine arcjet systems developed and tested under Lewis program. Each consists of thrustor, gas generator, and power-processing unit. Performance significantly improved. Technology transferred to user community, and first commercial flight anticipated in 1993.

Synthesis of Diverse Nitrogen-Enriched Heterocyclic Scaffolds Using a Suite of Tunable One-Pot Multicomponent Reactions

PubMed Central

2015-01-01

Five elegant and switchable three-component reactions which enable access to a new series of nitrogen-containing heterocycles are reported. A novel one-step addition of an isocyanide to a hydrazine derived Schiff base affords unique six-membered pyridotriazine scaffolds (A and E). With slight modification of reaction conditions and replacement of the nucleophilic isocyanide moiety with different electrophiles (i.e., isocyanates, isothiocyanates, cyclic anhydrides, and acyl chlorides) five-membered triazolopyridine scaffolds (B, D, F, G) are generated in a single step. Furthermore, the use of phenyl hydrazine enables access to dihydroindazole-carboxamides, devoid of a bridge-head nitrogen (C). All protocols are robust and tolerate a diverse collection of reactants, and as such, it is expected that the new scaffolds and associated chemistry will garner high interest from medicinal chemists involved in either file enhancement or specific target-related drug discovery campaigns. PMID:24788091

A highly selective long-wavelength fluorescent probe for hydrazine and its application in living cell imaging

NASA Astrophysics Data System (ADS)

Hao, Yuanqiang; Zhang, Yintang; Ruan, Kehong; Meng, Fanteng; Li, Ting; Guan, Jinsheng; Du, Lulu; Qu, Peng; Xu, Maotian

2017-09-01

A highly selective long-wavelength turn-on fluorescent probe has been developed for the detection of N2H4. The probe was prepared by conjugation the tricyanofuran-based D-π-A system with a recognizing moiety of acetyl group. In the presence of N2H4, the probe can be effectively hydrazinolysized and produce a turn-on fluorescent emission at 610 nm as well as a large red-shift in the absorption spectrum corresponding to a color change from yellow to blue. The sensing mechanism was confirmed by HPLC, MS, UV-vis, emission spectroscopic and theoretical calculation studies. The probe displayed high selectivity and sensitivity for N2H4 with a LOD (limit of detection) of 0.16 μM. Moreover, the probe was successfully utilized for the detection of hydrazine in living cells.

Propellant Vaporization as a Criterion for Rocket-Engine Design; Experimental Performance, Vaporization and Heat-Transfer Rates with Various Propellant Combinations

NASA Technical Reports Server (NTRS)

Clark, Bruce J.; Hersch, Martin; Priem, Richard J.

1959-01-01

Experimental combustion efficiencies of eleven propellant combinations were determined as a function of chamber length. Efficiencies were measured in terms of characteristic exhaust velocities at three chamber lengths and in terms of gas velocities. The data were obtained in a nominal 200-pound-thrust rocket engine. Injector and engine configurations were kept essentially the same to allow comparison of the performance. The data, except for those on hydrazine and ammonia-fluorine, agreed with predicted results based on the assumption that vaporization of the propellants determines the rate of combustion. Decomposition in the liquid phase may be.responsible for the anomalous behavior of hydrazine. Over-all heat-transfer rates were also measured for each combination. These rates were close to the values predicted by standard heat-transfer calculations except for the combinations using ammonia.

Earth storable bimodal engine, phase 1

NASA Technical Reports Server (NTRS)

1973-01-01

An in-depth study of an Earth Storable Bimodal (ESB) Engine using earth storable propellants N2O/N2H4 and operating in either a monopropellant or bipropellant mode was conducted. Detailed studies were completed for both a hot-gas, regeneratively cooled thrust chamber and a ducted hot-gas, film cooled thrust chamber. Hydrazine decomposition products were used for cooling in either configuration. The various arrangements and configurations of hydrazine reactors, secondary injectors, chambers and gimbal methods were considered. The two basic materials selected for the major components were columbium alloys and L-605. The secondary injector types considered were previously demonstrated by JPL and consisted of a liquid-on-gas triplet, a liquid-on-gas doublet, and a liquid-on-gas coaxial injector. Various design tradeoffs were made with different reactor types located at: the secondary injector station, the thrust chamber throat, and the nozzle/extension interface. Associated thermal, structural, and mass analyses were completed.

Thruster-Specific Force Estimation and Trending of Cassini Hydrazine Thrusters at Saturn

NASA Technical Reports Server (NTRS)

Stupik, Joan; Burk, Thomas A.

2016-01-01

The Cassini spacecraft has been in orbit around Saturn since 2004 and has since been approved for both a first and second extended mission. As hardware reaches and exceeds its documented life expectancy, it becomes vital to closely monitor hardware performance. The performance of the 1-N hydrazine attitude control thrusters is especially important to study, because the spacecraft is currently operating on the back-up thruster branch. Early identification of hardware degradation allows more time to develop mitigation strategies. There is no direct measure of an individual thruster's thrust magnitude, but these values can be estimated by post-processing spacecraft telemetry. This paper develops an algorithm to calculate the individual thrust magnitudes using Euler's equation. The algorithm correctly shows the known degradation in the first thruster branch, validating the approach. Results for the current thruster branch show nominal performance as of August, 2015.

(E)-1-(2,4-Di­nitro­phen­yl)-2-(3-eth­oxy-4-hy­droxy­benzyl­idene)hydrazine

PubMed Central

Fun, Hoong-Kun; Chantrapromma, Suchada; Ruanwas, Pumsak; Kobkeatthawin, Thawanrat; Chidan Kumar, C. S.

2014-01-01

The mol­ecule of the title hydrazine derivative, C15H14N4O6, is essentially planar, the dihedral angle between the substituted benzene rings being 2.25 (9)°. The eth­oxy and hy­droxy groups are almost coplanar with their bound benzene ring [r.m.s. deviation = 0.0153 (2) Å for the ten non-H atoms]. Intra­molecular N—H⋯O and O—H⋯Oeth­oxy hydrogen bonds generate S(6) and S(5) ring motifs, respectively. In the crystal, mol­ecules are linked by O—H⋯Onitro hydrogen bonds into chains propagating in [010]. Weak aromatic π–π inter­actions, with centroid–centroid distances of 3.8192 (19) and 4.0491 (19) Å, are also observed. PMID:24527018

Improvement in Titanium Complexes Bearing Schiff Base Ligands in the Ring-Opening Polymerization of L-Lactide: A Dinuclear System with Hydrazine-Bridging Schiff Base Ligands.

PubMed

Tseng, Hsi-Ching; Chen, Hsing-Yin; Huang, Yen-Tzu; Lu, Wei-Yi; Chang, Yu-Lun; Chiang, Michael Y; Lai, Yi-Chun; Chen, Hsuan-Ying

2016-02-15

A series of titanium (Ti) complexes bearing hydrazine-bridging Schiff base ligands were synthesized and investigated as catalysts for the ring-opening polymerization (ROP) of L-lactide (LA). Complexes with electron withdrawing or steric bulky groups reduced the catalytic activity. In addition, the steric bulky substituent on the imine groups reduced the space around the Ti atom and then reduced LA coordination with Ti atom, thereby reducing catalytic activity. All the dinuclear Ti complexes exhibited higher catalytic activity (approximately 10-60-fold) than mononuclear L(Cl-H)-TiOPr2 did. The strategy of bridging dinuclear Ti complexes with isopropoxide groups in the ROP of LA was successful, and adjusting the crowded heptacoordinated transition state by the bridging isopropoxide groups may be the key to our successful strategy.

Fluorination, Defluorination, Derivatization and Solvation of Single-Wall Carbon Nanotubes

NASA Astrophysics Data System (ADS)

Margrave, John L.

1999-10-01

Direct fluorination has been used to create fluoronanotubes which have active sites for derivatizing carbon nanotubes. A new technique using hydrazine and its derivatives has been used for defluorination of fluoronanotubes. The products include N2 and HF. Fluorinated species can be derivatized with R-Li or Grignard Reagents to form inorganic fluorides and derivatized products e.g., methyl, butyl or hexyl-nanotubes, (NH2)x-nanotubes, etc. Mass-spectra IR and Raman spectra along with electron microprobe analyses have been utilized, along with AFM, SEM and TEM to characterize the products. ``Fluorotubes" can be solvated as individual tubes in various alcohol solvents via ultrasonication. These solutions persist long enough (over a week) to permit solution phase chemistry to be carried out on the fluorotubes. For example, the solvated fluorotubes can be precipitated out of solution with hydrazine to yield normal, unfluorinated SWNTs or they can be reacted with sodium methoxide to yield methoxylated SWNTs.

Workers take off the protective covering on Cassini's propulsion module in SAEF-2

NASA Technical Reports Server (NTRS)

1997-01-01

Workers take off the protective covering on the propulsion module for the Cassini spacecraft after uncrating the module at KSC's Spacecraft Assembly and Encapsulation Facility-2 (SAEF-2). The extended journey of 6.7 years to Saturn and the 4-year mission for Cassini once it gets there will require the spacecraft to carry a large amount of propellant for inflight trajectory- correction maneuvers and attitude control, particularly during the science observations. The propulsion module has redundant 445-newton main engines that burn nitrogen tetraoxide and monomethyl-hydrazine for main propulsion and 16 smaller 1-newton engines that burn hydrazine to control attitude and to correct small deviations from the spacecraft flight path. Cassini will be launched on a Titan IVB/Centaur expendable launch vehicle. Liftoff is targeted for October 6 from Launch Complex 40, Cape Canaveral Air Station.

Determination of 17-oxosteroid glucuronides and sulfates in urine and serum by fluorescence high-performance liquid chromatography using dansyl hydrazine as a prelabeling reagent.

PubMed

Kawasaki, T; Maeda, M; Tsuji, A

1982-12-10

A fluorescence high-performance liquid chromatographic method is described for the direct determination of conjugated 17-oxosteroids in biological fluids without hydrolysis. Conjugated 17-oxosteroids are extracted with Sep-Pak C18 cartridge, labeled with dansyl hydrazine in trichloroacetic acid--benzene solution and then separated by high-performance liquid chromatography on reversed-phase muBondapak C18 column using 0.01 M sodium acetate in methanol-water-acetic acid (65:35:1, v/v) as the mobile phase. The eluate is monitored by a fluorophotometer at 365 nm (excitation) and 520 nm (emission). Linearities of fluorescence intensities (peak heights) with the amounts of various conjugated 17-oxosteroids were obtained between 10 pmol and 100 pmol. This method is sensitive, reliable and useful for the simultaneous determination of conjugated 17-oxosteroids in urine and serum.