Simultaneous determination of the potential carcinogen 1,4-dioxane and malodorous alkyl-1,3-dioxanes and alkyl-1,3-dioxolanes in environmental waters by solid-phase extraction and gas chromatography tandem mass spectrometry.

PubMed

Carrera, Guillem; Vegué, Lídia; Boleda, Mª Rosa; Ventura, Francesc

2017-03-03

1,4-dioxane is a synthetic industrial solvent used in various industrial processes, and it is a probable human carcinogen whose presence in the aquatic environment is frequently reported. Alkyl-1,3-dioxanes and alkyl-1,3-dioxolanes are compounds that have been identified as causing several odor episodes in waters over the last years, with the result of downtime of drinking water treatment plants. According to published studies, some of these episodes may be caused either by resins synthesis processes, or by industrial residues added to dehydrated sludge in wastewater treatment plants (WWTPs) in order to increase biogas production efficiency. Analytical methods based on closed loop stripping analysis (CLSA) are routinely used when taste and odor events appear, but this technique has demonstrated to be unsuitable to determine 1,4-dioxane at trace levels. In this context, drinking water companies tend to focus on determining odorous compounds, but not on those compounds that are potentially harmful. The suitability of a SPE method and further analysis by GC/MS-MS to simultaneously determine 1,4-dioxane and alkyl-1,3-dioxanes and dioxolanes has been demonstrated. Recoveries in surface waters spiked at 25ng/L ranged from 76% to 105%, whereas method quantification limits (MQLs) varied from 0.7 to 26ng/L for dioxanes, and dioxolanes and 50ng/L for 1,4-dioxane. Uncertainties were evaluated at two different concentrations, 0.02μg/L and 0.4μg/L, with values of 25% for 1,4-dioxane, and of 16-28% for alkyl-1,3-dioxanes and alkyl-1,3-dioxolanes for the later. The methodology has been successfully applied to samples from the aquifer of the Llobregat River (NE. Spain). Copyright © 2017 Elsevier B.V. All rights reserved.

1,4-Dioxane pollution at contaminated groundwater sites in western Germany and its distribution within a TCE plume.

PubMed

Karges, Ursula; Becker, Johannes; Püttmann, Wilhelm

2018-04-01

An effective and sensitive method for the analysis of 1,4-dioxane in water has been available since 2008 (EPA 522). This method is increasingly being applied to investigate the distribution of 1,4-dioxane in the aquatic environment. However, there is a need for more information about the possible occurrence of 1,4-dioxane in groundwater in Europe in general, and in Germany in particular, where virtually no data have been collected so far. The possible contamination of groundwater with 1,4-dioxane is of relevance to Germany because up to 70% of Germany's drinking water is obtained from groundwater and about 17% from river bank filtrate, which contains variable proportions of groundwater. The aim of the present study is to investigate selected and representative groundwater sites in Germany that have suspected occurrences of 1,4-dioxane. Five of the sites are well known for their volatile chlorinated hydrocarbon contamination, two sites have representative landfill leachate characteristics, and one site is negatively impacted by a detergent manufacturing plant. The presence of 1,4-dioxane was observed at each of these sites. Measured maximum concentration values ranged from 0.15μg/L to 152μg/L. An aquifer containing a trichloroethylene (TCE) plume with 1,4-dioxane as a co-contaminant was investigated in more detail. A perfect match was found between the concentrations of 1,4-dioxane and TCE in the vertical and horizontal distribution profiles. The results indicate the necessity for investigating groundwater contamination by 1,4-dioxane at sites with known 1,1,1-trichloroethane (TCA) and TCE contaminations, in landfill leachates, and at sites of detergent production. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of subsurface environment on oxidant activation and 1,4-dioxane degradation by in-situ chemical oxidation

NASA Astrophysics Data System (ADS)

Yan, N.; Brusseau, M. L. L.; Liu, F.

2017-12-01

The influence of groundwater and soil constituents on oxidant activation and 1,4-dioxane (dioxane) degradation by hydrogen peroxide coupled with persulfate was investigated through a series of batch experiments. The degradation of dioxane was considerably slower in groundwater compared to the tests conducted with ultrapure water. Additional tests were conducted to examine potential inhibitory effects of selected ions in isolation. The inhibition effect of anions on dioxane degradation, from strongest inhibition to weakest, was bicarbonate (HCO3-) > sulfate (SO42-) > chloride (Cl-). The inhibition effect of cations on dioxane degradation, from strongest inhibition to weakest, was calcium (Ca2+) > potassium (K+) > magnesium (Mg2+). Bicarbonate and calcium ions, which are the most abundant ions in the groundwater used herein, resulted in the greatest decrease in dioxane degradation rate compared to the other constituents. The impact of soil constituents was investigated by comparing dioxane degradation for bulk soil (soil without treatment), soil treated to remove organic matter (mineral fraction), and soil treated to remove organic matter and manganese oxides (iron fraction). Radical generation was measured by electron paramagnetic resonance (EPR) spectroscopy. The results of this study reveal potential inhibitory and synergistic effects caused by groundwater and soil constituents during the application of in-situ chemical oxidation.

Gas chromatographic determination of 1,4-dioxane at low parts-per-million levels in glycols.

PubMed

Pundlik, M D; Sitharaman, B; Kaur, I

2001-02-01

1,4-Dioxane is a flammable liquid and tends to form explosive peroxides. Its formation in glycols (low parts-per-million levels), which are used as dehumidifying agents in refineries, may take place by condensation. 1,4-Dioxane thus formed gets distilled over with benzene in the refinery process. Therefore, it is necessary to identify and determine the levels of 1,4-dioxane in glycols as well as benzene. Gas chromatography (GC) is probably the best technique for this purpose. GC analysis may be carried out using a flame ionization detector. Results show that 1,4-dioxane can be comfortably determined down to 2 ppm in glycols and benzene.

Decomposition of 1,4-dioxane by advanced oxidation and biochemical process.

PubMed

Kim, Chang-Gyun; Seo, Hyung-Joon; Lee, Byung-Ryul

2006-01-01

This study was undertaken to determine the optimal decomposition conditions when 1,4-dioxane was degraded using either the AOPs (Advanced Oxidation Processes) or the BAC-TERRA microbial complex. The advanced oxidation was operated with H2O2, in the range 4.7 to 51 mM, under 254 nm (25 W lamp) illumination, while varying the reaction parameters, such as the air flow rate and reaction time. The greatest oxidation rate (96%) of 1,4-dioxane was achieved with H2O2 concentration of 17 mM after a 2-hr reaction. As a result of this reaction, organic acid intermediates were formed, such as acetic, propionic and butyric acids. Furthermore, the study revealed that suspended particles, i.e., bio-flocs, kaolin and pozzolan, in the reaction were able to have an impact on the extent of 1,4-dioxane decomposition. The decomposition of 1,4-dioxane in the presence of bio-flocs was significantly declined due to hindered UV penetration through the solution as a result of the consistent dispersion of bio-particles. In contrast, dosing with pozzolan decomposed up to 98.8% of the 1,4-dioxane after 2 hr of reaction. Two actual wastewaters, from polyester manufacturing, containing 1,4-dioxane in the range 370 to 450 mg/L were able to be oxidized by as high as 100% within 15 min with the introduction of 100:200 (mg/L) Fe(II):H202 under UV illumination. Aerobic biological decomposition, employing BAC-TERRA, was able to remove up to 90% of 1,4-dioxane after 15 days of incubation. In the meantime, the by-products (i.e., acetic, propionic and valeric acid) generated were similar to those formed during the AOPs investigation. According to kinetic studies, both photo-decomposition and biodegradation of 1,4-dioxane followed pseudo first-order reaction kinetics, with k = 5 x 10(-4) s(-1) and 2.38 x 10(-6) s(-1), respectively. It was concluded that 1,4-dioxane could be readily degraded by both AOPs and BAC-TERRA, and that the actual polyester wastewater containing 1,4-dioxane could be successfully decomposed under the conditions of photo-Fenton oxidation.

IN-SITU OXIDATION OF 1,4-DIOXANE (LABORATORY RESULTS)

EPA Science Inventory

Interest in the solvent stabilizer, 1,4-dioxane, is increasing because analytical detection limits have decreased indicating its presence at chlorinated volatile organic compound contaminated sites. The most common method for removing 1,4-dioxane from contaminated water is advanc...

IRIS TOXICOLOGICAL REVIEW AND SUMMARY DOCUMENTS FOR 1,4 - DIOXANE

EPA Science Inventory

1,4 -Dioxane is a cyclic ether that is primarily utilized for industrial applications. These applications include 1,4 -dioxane as a solvent, reaction medium, wetting, degreasing, and dispersing agent, and for stabilization of chlorinated solvents (e.g. 1,1,1 -trichloroethane). ...

IRIS Toxicological Review of 1,4-Dioxane (Final Report)

EPA Science Inventory

EPA announced the release of the final report, Toxicological Review of 1,4-Dioxane (CAS No. 123-91-1): In Support of Summary Information on the Integrated Risk Information System (IRIS). The final Toxicological Review of 1,4-dioxane provides scientific support and rationa...

Oxygenase-Catalyzed Biodegradation of Emerging Water Contaminants: 1,4-Dioxane and N-Nitrosodimethylamine

DTIC Science & Technology

2012-02-01

and treat operations (54, 144). Aitchison et al. (1) have reported phytoremediation of dioxane by hybrid poplar trees. In their laboratory studies... Phytoremediation of 1,4-dioxane by hybrid poplar trees. Water Environ. Res. 72:313-321. 2. Alber, B. E. 2011. Biotechnological potential of the

Laboratory Investigations Of Mechanisms For 1,4-Dioxane Destruction By Ozone In Water (Presentation)

EPA Science Inventory

Advances in analytical detection methods have made it possible to quantify 1,4-dioxane contamination in groundwater, even a well-characterized sites where it had not been previously detected. Although 1,4-dioxane is difficult to treat because of its chemical and physical propert...

Laboratory Investigation Of Mechanisms For 1,4-Dioxane Destruction By Ozone In Water

EPA Science Inventory

Advances in analytical detection methods have made it possible to quantify 1,4-dioxane contamination in groundwater, even at well-characterized sites where it had not been previously detected. Although 1,4-dioxane is difficult to treat because of its chemical and physical proper...

Novel 1,3-dioxanes from apple juice and cider.

PubMed

Kavvadias, D; Beuerle, T; Wein, M; Boss, B; König, T; Schwab, W

1999-12-01

Extracts obtained by XAD solid-phase extraction of apple juice and cider were separated by liquid chromatography on silica gel. Several new 1,3-dioxanes including the known 2-methyl-4-pentyl-1,3-dioxane and 2-methyl-4-[2'(Z)-pentenyl]-1,3-dioxane, were identified in the nonpolar fractions by GC/MS analysis and confirmed by chemical synthesis. The enantioselective synthesis of the stereoisomers of the 1,3-dioxanes was performed using (R)- and (R,S)-octane-1,3-diol and (R)- and (R,S)-5(Z)-octene-1,3-diol as starting material. Comparison with the isolated products indicated that the natural products consisted of a mixture of (2S,4R) and (2R,4R) stereoisomers in the ratio of approximately 10:1, except for 1,3-dioxanes generated from acetone and 2-butanone. It is assumed that the 1, 3-dioxanes are chemically formed in the apples and cider from the natural apple ingredients (R)-octane-1,3-diol, (R)-5(Z)-octene-1, 3-diol, (3R,7R)- and (3R,7S)-octane-1,3,7-triol, and the appropriate aldehydes and ketones, which are produced either by the apples or by yeast during fermentation of the apple juice.

Enthalpy-entropy compensation for the solubility of drugs in solvent mixtures: paracetamol, acetanilide, and nalidixic acid in dioxane-water.

PubMed

Bustamante, P; Romero, S; Pena, A; Escalera, B; Reillo, A

1998-12-01

In earlier work, a nonlinear enthalpy-entropy compensation was observed for the solubility of phenacetin in dioxane-water mixtures. This effect had not been earlier reported for the solubility of drugs in solvent mixtures. To gain insight into the compensation effect, the behavior of the apparent thermodynamic magnitudes for the solubility of paracetamol, acetanilide, and nalidixic acid is studied in this work. The solubility of these drugs was measured at several temperatures in dioxane-water mixtures. DSC analysis was performed on the original powders and on the solid phases after equilibration with the solvent mixture. The thermal properties of the solid phases did not show significant changes. The three drugs display a solubility maximum against the cosolvent ratio. The solubility peaks of acetanilide and nalidixic acid shift to a more polar region at the higher temperatures. Nonlinear van't Hoff plots were observed for nalidixic acid whereas acetanilide and paracetamol show linear behavior at the temperature range studied. The apparent enthalpies of solution are endothermic going through a maximum at 50% dioxane. Two different mechanisms, entropy and enthalpy, are suggested to be the driving forces that increase the solubility of the three drugs. Solubility is entropy controlled at the water-rich region (0-50% dioxane) and enthalpy controlled at the dioxane-rich region (50-100% dioxane). The enthalpy-entropy compensation analysis also suggests that two different mechanisms, dependent on cosolvent ratio, are involved in the solubility enhancement of the three drugs. The plots of deltaH versus deltaG are nonlinear, and the slope changes from positive to negative above 50% dioxane. The compensation effect for the thermodynamic magnitudes of transfer from water to the aqueous mixtures can be described by a common empirical nonlinear relationship, with the exception of paracetamol, which follows a separate linear relationship at dioxane ratios above 50%. The results corroborate earlier findings with phenacetin. The similar pattern shown by the drugs studied suggests that the nonlinear enthalpy-entropy compensation effect may be characteristic of the solubility of semipolar drugs in dioxane-water mixtures.

Controlling the Conformational Energy of a Phenyl Group by Tuning the Strength of a Nonclassical CH···O Hydrogen Bond: The Case of 5-Phenyl-1,3-dioxane.

PubMed

Bailey, William F; Lambert, Kyle M; Stempel, Zachary D; Wiberg, Kenneth B; Mercado, Brandon Q

2016-12-16

Anancomeric 5-phenyl-1,3-dioxanes provide a unique opportunity to study factors that control conformation. Whereas one might expect an axial phenyl group at C(5) of 1,3-dioxane to adopt a conformation similar to that in axial phenylcyclohexane, a series of studies including X-ray crystallography, NOE measurements, and DFT calculations demonstrate that the phenyl prefers to lie over the dioxane ring in order to position an ortho-hydrogen to participate in a stabilizing, nonclassical CH···O hydrogen bond with a ring oxygen of the dioxane. Acid-catalyzed equilibration of a series of anancomeric 2-tert-butyl-5-aryl-1,3-dioxane isomers demonstrates that remote substituents on the phenyl ring affect the conformational energy of a 5-aryl-1,3-dioxane: electron-withdrawing substituents decrease the conformational energy of the aryl group, while electron-donating substituents increase the conformational energy of the group. This effect is correlated in a very linear way to Hammett substituent parameters. In short, the strength of the CH···O hydrogen bond may be tuned in a predictable way in response to the electron-withdrawing or electron-donating ability of substituents positioned remotely on the aryl ring. This effect may be profound: a 3,5-bis-CF 3 phenyl group at C(5) in 1,3-dioxane displays a pronounced preference for the axial orientation. The results are relevant to broader conformational issues involving heterocyclic systems bearing aryl substituents.

IRIS Toxicological Review of 1,4-Dioxane (Interagency ...

EPA Pesticide Factsheets

On September 9, 2011, the Toxicological Review of 1,4-Dioxane (with inhalation update) (External Review Draft) was posted for external peer review and public comment. The Toxicological Review and charge were reviewed internally by EPA and by other federal agencies and White House Offices before public release. In the new IRIS process, introduced by the EPA Administrator, all written comments on IRIS assessments submitted by other federal agencies and White House Offices will be made publicly available. Accordingly, interagency comments with EPA's response and the interagency science consultation draft of the IRIS Toxicological Review of 1,4-dioxane and the charge to external peer reviewers are posted on this site. The Toxicological Review of 1,4-dioxane provides scientific support and rationale for the hazard and dose-response assessment pertaining to chronic exposure to 1,4-dioxane.

Characterizing the intrinsic bioremediation potential of 1,4-dioxane and trichloroethene using innovative environmental diagnostic tools.

PubMed

Chiang, Sheau-Yun Dora; Mora, Rebecca; Diguiseppi, William H; Davis, Greg; Sublette, Kerry; Gedalanga, Phillip; Mahendra, Shaily

2012-09-01

An intrinsic biodegradation study involving the design and implementation of innovative environmental diagnostic tools was conducted to evaluate whether monitored natural attenuation (MNA) could be considered as part of the remedial strategy to treat an aerobic aquifer contaminated with 1,4-dioxane and trichloroethene (TCE). In this study, advanced molecular biological and stable isotopic tools were applied to confirm in situ intrinsic biodegradation of 1,4-dioxane and TCE. Analyses of Bio-Trap® samplers and groundwater samples collected from monitoring wells verified the abundance of bacteria and enzymes capable of aerobically degrading TCE and 1,4-dioxane. Furthermore, phospholipid fatty acid analysis with stable isotope probes (PLFA-SIP) of the microbial community validated the ability for microbial degradation of TCE and 1,4-dioxane. Compound specific isotope analysis (CSIA) of groundwater samples for TCE resulted in δ(13)C values that indicated likely biodegradation of TCE in three of the four monitoring wells sampled. Results of the MNA evaluation showed that enzymes capable of aerobically degrading TCE and 1,4-dioxane were present, abundant, and active in the aquifer. Taken together, these results provide direct evidence of the occurrence of TCE and 1,4-dioxane biodegradation at the study site, supporting the selection of MNA as part of the final remedy at some point in the future.

Method Development for the Analysis of 1,4-Dioxane in Drinking Water Using Solid Phase Extraction and Gas Chromatography/Mass Spectrometry

EPA Science Inventory

1,4-Dioxane has been identified as a probable human carcinogen and an emerging contaminant in drinking water. The National Exposure Research Laboratory (NERL) has developed a method for the analysis of 1,4-dioxane in drinking water at ng/L concentrations. The method consists of...

IRIS Toxicological Review of 1,4-Dioxane (with Inhalation ...

EPA Pesticide Factsheets

On September 9, 2011, the Toxicological Review of 1,4-Dioxane (inhalation) (External Review Draft) was posted for external peer review and public comment. Subsequently, the Toxicological Review and IRIS Summary were reviewed internally by EPA and by other federal agencies and Executive Office of the President before final public release. Based on the 2009 IRIS assessment development process, all written comments on IRIS assessments submitted by other federal agencies and the Executive Office of the President will be made publicly available. Accordingly, interagency comments with EPA's response and the interagency science discussion draft of the IRIS Toxicological Review of 1,4-dioxane (with inhalation update) and the draft IRIS Summary are posted on this site. The Toxicological Review of 1,4-dioxane provides scientific support and rationale for the hazard and dose-response assessment pertaining to chronic exposure to 1,4-dioxane.

Preparation of uranium compounds

DOEpatents

Kiplinger, Jaqueline L; Montreal, Marisa J; Thomson, Robert K; Cantat, Thibault; Travia, Nicholas E

2013-02-19

UI.sub.3(1,4-dioxane).sub.1.5 and UI.sub.4(1,4-dioxane).sub.2, were synthesized in high yield by reacting turnings of elemental uranium with iodine dissolved in 1,4-dioxane under mild conditions. These molecular compounds of uranium are thermally stable and excellent precursor materials for synthesizing other molecular compounds of uranium including alkoxide, amide, organometallic, and halide compounds.

Phytoremediation of 1,4-dioxane-containing recovered groundwater.

PubMed

Ferro, Ari M; Kennedy, Jean; LaRue, James C

2013-01-01

The results of a pilot-scale phytoremediation study are reported in this paper. Small plots of trees established on a closed municipal waste landfill site were irrigated with recovered groundwater containing 1,4-dioxane (dioxane) and other volatile organic compounds (VOCs). The plots were managed to minimize the leaching of irrigation water, and leaching was quantified by the use of bromide tracer. Results indicated that the dioxane (2.5 microg/L) was effectively removed, probably via phytovolatilization, and that a full-scale phytoremediation system could be used. A system is now in place at the site in which the recovered groundwater can be treated using two different approaches. A physical treatment system (PTS) will be used during the winter months, and a 12 ha phytoremediation system (stands of coniferous trees) will be used during the growing season. The PTS removes VOCs using an air-stripper, and destroys dioxane using a photo-catalytic oxidation process. Treated water will be routed to the local sewer system. The phytoremediation system, located on the landfill, will be irrigated with effluent from the PTS air-stripper containing dioxane. Seasonal use of the phytoremediation system will reduce reliance on the photo-catalytic oxidation process that is extremely energy consumptive and expensive to operate.

Method 522 - Determination of 1,4-Dioxane in Drinking Water by Solid Phase Extraction (SPE) and Gas Chromatography Mass Spectrometry (GC/MS) with Selected Ion Monitoring (SIM)

EPA Science Inventory

1,4-Dioxane has been identified as a probable human carcinogen and an emerging contaminant in drinking water. The National Exposure Research Laboratory (NERL) has developed a method for the analysis of 1,4-dioxane in drinking water at ng/L concentrations. The method consists of...

IRIS Toxicological Review of 1,4-Dioxane (with Inhalation ...

EPA Pesticide Factsheets

EPA is conducting a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of 1,4-Dioxane (with inhalation update) that when finalized will appear on the Integrated Risk Information System (IRIS) database. 1,4-Dioxane is commonly used as a solvent, cleaning agent, chemical stabilizer, surface coating, adhesive agent, and an ingredient in chemical manufacture.

1,4-Dioxane drinking water occurrence data from the third unregulated contaminant monitoring rule.

PubMed

Adamson, David T; Piña, Elizabeth A; Cartwright, Abigail E; Rauch, Sharon R; Hunter Anderson, R; Mohr, Thomas; Connor, John A

2017-10-15

This study examined data collected from U.S. public drinking water supplies in support of the recently-completed third round of the Unregulated Contaminant Monitoring Rule (UCMR3) to better understand the nature and occurrence of 1,4-dioxane and the basis for establishing drinking water standards. The purpose was to evaluate whether the occurrence data for this emerging but federally-unregulated contaminant fit with common conceptual models, including its persistence and the importance of groundwater contamination for potential exposure. 1,4-Dioxane was detected in samples from 21% of 4864 PWSs, and was in exceedance of the health-based reference concentration (0.35μg/L) at 6.9% of these systems. In both measures, it ranked second among the 28 UCMR3 contaminants. Although much of the focus on 1,4-dioxane has been its role as a groundwater contaminant, the detection frequency for 1,4-dioxane in surface water was only marginally lower than in groundwater (by a factor of 1.25; p<0.0001). However, groundwater concentrations were higher than those in surface water (p<0.0001) and contributed to a higher frequency of exceeding the reference concentration (by a factor of 1.8, p<0.0001), indicating that surface water sources tend to be more dilute. Sampling from large systems increased the likelihood that 1,4-dioxane was detected by a factor of 2.18 times relative to small systems (p<0.0001). 1,4-Dioxane detections in drinking water were highly associated with detections of other chlorinated compounds particularly 1,1-dichlorethane (odds ratio=47; p<0.0001), which is associated with the release of 1,4-dioxane as a chlorinated solvent stabilizer. Based on aggregated nationwide data, 1,4-dioxane showed evidence of a decreasing trend in concentration and detection frequency over time. These data suggest that the loading to drinking water supplies may be decreasing. However, in the interim, some water supply systems may need to consider improving their treatment capabilities in response to further regulatory review of this compound. Copyright © 2017 Elsevier B.V. All rights reserved.

Removal of 1,4-dioxane from industrial wastewaters: routes of decomposition under different operational conditions to determine the ozone oxidation capacity.

PubMed

Barndõk, Helen; Cortijo, Luis; Hermosilla, Daphne; Negro, Carlos; Blanco, Angeles

2014-09-15

This paper denotes the importance of operational parameters for the feasibility of ozone (O3) oxidation for the treatment of wastewaters containing 1,4-dioxane. Results show that O3 process, which has formerly been considered insufficient as a sole treatment for such wastewaters, could be a viable treatment for the degradation of 1,4-dioxane at the adequate operation conditions. The treatment of both synthetic solution of 1,4-dioxane and industrial wastewaters, containing 1,4-dioxane and 2-methyl-1,3-dioxolane (MDO), showed that about 90% of chemical oxygen demand can be removed and almost a total removal of 1,4-dioxane and MDO is reached by O3 at optimal process conditions. Data from on-line Fourier transform infrared spectroscopy provides a good insight to its different decomposition routes that eventually determine the viability of degrading this toxic and hazardous compound from industrial waters. The degradation at pH>9 occurs faster through the formation of ethylene glycol as a primary intermediate; whereas the decomposition in acidic conditions (pH<5.7) consists in the formation and slower degradation of ethylene glycol diformate. Copyright © 2014 Elsevier B.V. All rights reserved.

Genome Sequence of the 1,4-Dioxane-Degrading Pseudonocardia dioxanivoransStrain CB1190▿

PubMed Central

Sales, Christopher M.; Mahendra, Shaily; Grostern, Ariel; Parales, Rebecca E.; Goodwin, Lynne A.; Woyke, Tanja; Nolan, Matt; Lapidus, Alla; Chertkov, Olga; Ovchinnikova, Galina; Sczyrba, Alexander; Alvarez-Cohen, Lisa

2011-01-01

Pseudonocardia dioxanivoransCB1190 is the first bacterium reported to be capable of growth on the environmental contaminant 1,4-dioxane and the first member of the genus Pseudonocardiafor which there is an annotated genome sequence. Preliminary analysis of the genome (chromosome and three plasmids) indicates that strain CB1190 possesses several multicomponent monooxygenases that could be involved in the aerobic degradation of 1,4-dioxane and other environmental contaminants. PMID:21725009

Molecular Interactions in 1,4-Dioxane, Tetrahydrofuran, and Ethyl Acetate Solutions of 1,1'-Bis(4-isopropyloxyacetylphenoxy)cyclohexane on Reological, Density, and Acoustic Behavior

NASA Astrophysics Data System (ADS)

Dhaduk, B. B.; Patel, Ch. B.; Parsania, P. H.

2017-12-01

Various thermo-acoustical parameters of 1,4-dioxane, tetrahydofuran and ethylacetae solutions of 1,1'-bis(4-isopropyloxyacetylphenoxy)cyclohexane were determined at different temperatures using density, viscosity and ultrasonic speed and correlated with concentration. Linear increase of ultrasonic speed, specific acoustical impedance, Rao's molar sound function, Van der Waals constant and free volume with concentration C and decreased with temperature. Linear decrease of adiabatic compressibility, internal pressure, intermolecular free path length, classical absorption coefficient, and viscous relaxation time with concentration and increased with temperature indicated existence of strong molecular interactions in solutions and further supported by positive values of solvation number. Gibbs free energy of activation decreased with C in all three systems. It is decreased with T in 1,4-dioxane, while increased in tetrahydrofuran and ethyl acetate. Both enthalpy of activation and entropy of activation are increased gradually with C in 1,4-dioxane, while they are negative and remained practically independent of concentration in 1,4-dioxane and tetrahydofuran systems.

Proof-of-Concept Study: Novel Microbially-Driven Fenton Reaction for In Situ Remediation of Groundwater Contaminated with 1,4-Dioxane, Tetrachloroethene (PCE) and Trichloroethene (TCE)

DTIC Science & Technology

2014-09-17

technologies such as carbon absorption, air stripping, and distillation are limited by the physical properties of 1-4-dioxane. In the present study, a...and also to evaluate the ability of the novel degradation process to degrade perfluoroalkyl ( PFAS ) substances. 4 INTRODUCTION 1,4...miscible in water, displays low volatility, and is thus highly mobile in the environment. Current 1,4-dioxane remediation technologies such as carbon

Technical Fact Sheet – 1,4-Dioxane

EPA Pesticide Factsheets

This fact sheet, developed by the U.S. Environmental Protection Agency (EPA) Federal Facilities Restoration and Reuse Office (FFRRO), provides a brief summary of the contaminant 1,4-dioxane, including physical and chemical properties

Cryochemistry: freezing effect on peptide coupling in different organic solutions.

PubMed

Vajda, T; Szókán, G; Hollósi, M

1998-06-01

The freezing effect on peptide coupling in organic solutions of different polarity has been investigated and compared with the results obtained in liquid phase. The model reaction of DCC-activated coupling of Boc-Ala-Phe-OH with H-Ala-OBu(t) has been carried out in dioxane, dimethylsulfoxide and formamide, as well as in mixtures (90%/10%, v/v) of dioxane with acetonitrile, dimethylformamide, dimethylsulfoxide and formamide. The reactions have been traced and evaluated by RP-HPLC analysis. Freezing the reaction mixture resulted in all cases in a significant suppression of the N-dipeptidylurea side-product formation together with a slight decrease of tripeptide epimerization. The coupling yields and the side effects depended on the solvent, with the dioxane and dioxane/acetonitrile mixture produced the best results. The role of freezing and solvent in the improved results is discussed.

Physiologically based Pharmacokinetic Modeling of 1,4-Dioxane in Rats, Mice, and Humans

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sweeney, Lisa M.; Thrall, Karla D.; Poet, Torka S.

2008-01-01

ABSTRACT 1,4-Dioxane (CAS No. 123-91-1) is used primarily as a solvent or as a solvent stabilizer. It can cause lung, liver and kidney damage at sufficiently high exposure levels. Two physiologically-based pharmacokinetic (PBPK) models of 1,4-dioxane and its major metabolite, hydroxyethoxyacetic acid (HEAA), were published in 1990. These models have uncertainties and deficiencies that could be addressed and the model strengthened for use in a contemporary cancer risk assessment for 1,4-dioxane. Studies were performed to fill data gaps and reduce uncertainties pertaining to the pharmacokinetics of 1,4-dioxane and HEAA in rats, mice, and humans. Three types of studies were performed:partitionmore » coefficient measurements, blood time course in mice, and in vitro pharmacokinetics using rat, mouse, and human hepatocytes. Updated PBPK models were developed based on these new data and previously available data. The optimized rate of metabolism for the mouse was significantly higher than the value previously estimated. The optimized rat kinetic parameters were similar to those in the 1990 models. Only two human studies were identified. Model predictions were consistent with one study, but did not fit the second as well. In addition, a rat nasal exposure was completed. The results confirmed water directly contacts rat nasal tissues during drinking water under bioassays. Consistent with previous PBPK models, nasal tissues were not specifically included in the model. Use of these models will reduce the uncertainty in future 1,4-dioxane risk assessments.« less

The synthesis and the spectroscopic, thermal, and structural properties of the M2[(fumarate)Ni(CN)4]·2(1,4-Dioxane) clathrate (M = Co, Ni, Cd and Hg)

NASA Astrophysics Data System (ADS)

Kartal, Zeki; Yavuz, Abdülkerim

2018-03-01

In this study, the clathrates of fumarate-tetracyanonickel-dioxane, given by the formula M2[(fumarate)Ni(CN)4]·2(1,4-Dioxane) (M = Co, Ni, Cd and Hg), have been obtained for the first time through chemical methods. These clathrates have been characterized by elemental, thermal, FT-IR, and FT-Raman spectroscopies. The parameters of structures of clathrates have been determined by X-ray powder diffraction. The thermal behaviors of these clathrates have been also investigated by thermo-gravimetric analysis (TGA), differential thermal analysis (DTA), and derivative thermal gravimetric analysis (DTG) in the range of 20-900 °C. X-ray powder diffraction data have been recorded at ambient temperature in the 2θ range 5-50°. The FT-IR and FT-Raman spectra of clathrates have been recorded in the region of 4000-400 cm-1 and 4000-100 cm-1, respectively. The results of the spectral and thermal analyses of the newly synthesized clathrates of fumarate-tetracyanonickel-dioxane suggest that these clathrates are new examples of the Hofmann-type dioxane clathrates. In our study, the Hofmann-type dioxane clathrates, which are formed by bounding electrons of oxygen-donor atoms of fumarate ion ligand molecule to transition metal atoms, consist of the corrugated |M-Ni(CN)4|∞ polymeric layers, which are held in parallel through the chain of (-M-fumarate-M-).

Concentration and trend of 1,4-dioxane in wells sampled during 2002–2017 in the vicinity of the Tucson International Airport Area Superfund Site, Arizona

USGS Publications Warehouse

Tillman, Fred D.

2017-09-25

Industrial activities causing extensive groundwater contamination led to the listing of the Tucson International Airport Area (TIAA) as a Superfund Site in 1983. Early groundwater investigations identified volatile organic compounds (VOCs), including the chlorinated solvents trichloroethylene (TCE) and perchloroethylene (PCE), in wells in the area. Several responsible parties were identified and cleanup activities began in the late 1980s. In 2002, the compound 1,4-dioxane was discovered in wells in the area and has since been detected in measurable concentrations throughout the site. The U.S. Environmental Protection Agency (USEPA) classifies 1,4-dioxane as a likely human carcinogen.The purpose of this map is to present 1,4-dioxane concentrations in wells sampled from 2002 through mid-2017 in the TIAA Superfund Site area to indicate both the current status and trends in 1,4-dioxane groundwater contamination. This map includes data from wells in the commercial and residential community in the TIAA and does not include data from wells in suspected or confirmed source areas, such as Air Force Plant 44 and Tucson International Airport, or from wells within treatment facilities.

Determination of residual 1,4-dioxane in surfactants and cleaning agents using headspace single-drop microextraction followed by gas chromatography-flame ionization detection.

PubMed

Saraji, M; Shirvani, N

2017-02-01

Polyethoxylated surfactants are widely used in the formulation of different cleaning agents such as shampoo, dish washing and hand washing products and lotion formulation. During the production of polyethoxylated surfactants, 1,4-dioxane as a toxic and carcinogenic by-product is formed. A simple low-cost method based on headspace single-drop microextraction combined with gas chromatography-flame ionization detection was developed for the determination of 1,4-dioxane in surfactants and cleaning agents. In this method, 1,4-dioxane was extracted from 8.0 mL sample solution into a microdrop of an organic solvent, and then, it was injected to gas chromatography. The effects of such parameters as the solvent type, salt addition, microdrop volume, stirring rate, equilibrium time, extraction time and the temperature of sample solution on the extraction performance were studied and optimized. An ethoxylated surfactant containing 1,4-dioxane was used as the sample for the optimization of the extraction parameters. The linear range, determination coefficient, limit of detection and relative standard deviation of the method were 0.5-100 μg g -1 , 0.9977, 0.4 μg g -1 and 7.2% (n = 5), respectively. Different real samples including sodium lauryl ether sulphate, sodium lauryl sulphate (SLS), four brands of shampoo, and hand washing and dish washing liquids were analysed by the method. 1,4-Dioxane was detected at the concentration range of 2.4-201 μg g -1 in the samples, except dish washing liquid and SLS. A new method with the merits of simplicity, low cost, low organic solvent consumption, short analysis time, good repeatability and suitable detection limit was developed for the analysis of 1,4-dioxane in surfactants and cleaning agents. © 2016 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Dioxane contributes to the altered conformation and oligomerization state of a designed engrailed homeodomain variant

PubMed Central

Hom, Geoffrey K.; Lassila, J. Kyle; Thomas, Leonard M.; Mayo, Stephen L.

2005-01-01

Our goal was to compute a stable, full-sequence design of the Drosophila melanogaster engrailed homeodomain. Thermal and chemical denaturation data indicated the design was significantly more stable than was the wild-type protein. The data were also nearly identical to those for a similar, later full-sequence design, which was shown by NMR to adopt the homeodomain fold: a three-helix, globular monomer. However, a 1.65 Å crystal structure of the design described here turned out to be of a completely different fold: a four-helix, rodlike tetramer. The crystallization conditions included ~25% dioxane, and subsequent experiments by circular dichroism and sedimentation velocity analytical ultracentrifugation indicated that dioxane increases the helicity and oligomerization state of the designed protein. We attribute at least part of the discrepancy between the target fold and the crystal structure to the presence of a high concentration of dioxane. PMID:15741348

Method development for the analysis of 1,4-dioxane in drinking water using solid-phase extraction and gas chromatography-mass spectrometry.

PubMed

Grimmett, Paul E; Munch, Jean W

2009-01-01

1,4-Dioxane has been identified as a probable human carcinogen and an emerging contaminant in drinking water. The United States Environmental Protection Agency's (U.S. EPA) National Exposure Research Laboratory (NERL) has developed a method for the analysis of 1,4-dioxane in drinking water at ng/L concentrations. The method consists of an activated carbon solid-phase extraction of 500-mL or 100-mL water samples using dichloromethane as the elution solvent. The extracts are analyzed by gas chromatography-mass spectrometry (GC-MS) in selected ion monitoring (SIM) mode. In the NERL laboratory, recovery of 1,4-dioxane ranged from 94-110% in fortified laboratory reagent water and recoveries of 96-102% were demonstrated for fortified drinking water samples. The relative standard deviations for replicate analyses were less than 6% at concentrations exceeding the minimum reporting level.

Results of the Analyses for 1,4-Dioxane of Groundwater Samples Collected in the Tucson Airport Remediation Project Area, South-Central Arizona, 2006-2009

USGS Publications Warehouse

Tillman, Fred D.

2009-01-01

Extensive groundwater contamination resulting from industrial activities led to the listing of the Tucson International Airport Area (TIAA) as a Superfund Site by the U.S. Environmental Protection Agency (USEPA) in 1983. Early investigations revealed elevated levels of volatile organic compounds (VOCs), including the chlorinated solvents trichloroethylene and perchloroethylene, in wells in the area. Several responsible parties were identified, and cleanup activities were initiated in the late 1980s using technology designed for removal of VOCs. In 2002, the compound 1,4-dioxane was discovered in wells in the TIAA area. Since then, 1,4-dioxane has been detected throughout the TIAA area at levels exceeding the USEPA Drinking Water Health Advisory value of 3 micrograms per liter (ug/L; U.S. Environmental Protection Agency, 2006). Chemical properties of 1,4-dioxane make it relatively unaffected by the treatment technologies employed in the TIAA area. In 2006, the U.S. Geological Survey (USGS) Arizona Water Science Center, in cooperation with the U.S. Air Force Center for Engineering and the Environment, began an investigation into the extent of groundwater contamination by 1,4-dioxane in the area. Five rounds of groundwater sampling in the TIAA area have been completed by the USGS since that time, yielding a total of 210 samples. Results from these analyses indicate less than reportable concentrations of 1,4-dioxane in 30 percent of the samples, with 46 percent of the samples having concentrations at or above the USEPA Drinking Water Health Advisory level.

1,4-Dioxane

Integrated Risk Information System (IRIS)

EPA / 635 / R - 11 / 003F www.epa.gov / iris TOXICOLOGICAL REVIEW OF 1,4 - DIOXANE ( WITH INHALATION UPDATE ) ( CAS No . 123 - 91 - 1 ) In Support of Summary Information on the Integrated Risk Information System ( IRIS ) September 2013 U.S . Environmental Protection Agency Washington , DC DISCLAIMER

IRIS Toxicological Review of 1,4-Dioxane (External Review Draft, 2009)

EPA Science Inventory

EPA is conducting a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of 1,4-dioxane that when finalized will appear on the Integrated Risk Information System (IRIS) database.

Update: Mode of action (MOA) for liver tumors induced by oral exposure to 1,4-dioxane.

PubMed

Dourson, Michael L; Higginbotham, Jeri; Crum, Jeff; Burleigh-Flayer, Heather; Nance, Patricia; Forsberg, Norman D; Lafranconi, Mark; Reichard, John

2017-08-01

Previous work has shown that the weight of evidence supports the hypothesis that 1,4-dioxane causes liver tumors in rodents through cytotoxicity and subsequent regenerative hyperplasia. Questions regarding a lack of concordant findings for this mode of action (MOA) in mice have not been resolved, however. In the current work, a reanalysis of data from two chronic mouse cancer bioassays on 1,4-dioxane, one 13-week mouse study, seven rat cancer bioassays, coupled with other data such as 1,4-dioxane's negative mutagenicity, its lack of up-regulated DNA repair, and the appearance of liver tumors with a high background incidence, support the conclusion that rodent liver tumors, including those in mice, are evoked by a regenerative hyperplasia MOA. The initiating event for this MOA is metabolic saturation of 1,4-dioxane. Above metabolic saturation, higher doses of the parent compound cause an ever increasing toxicity in the rodent liver as evidenced by higher blood levels of enzymes indicative of liver cell damage and associated histopathology that occurs in a dose and time related manner. Importantly, alternative modes of action can be excluded. The observed liver toxicity has a threshold in the dose scale at or below levels that saturate metabolism, and generally in the range of 9.6-42 mg/kg-day for rats and 57 to 66 mg/kg-day for mice. It follows that threshold approaches to the assessment of this chemical's toxicity are supported by the non-mutagenic, metabolic saturation kinetics, and cytotoxicity-generated regenerative repair information available for 1,4-dioxane promoted rodent liver tumors. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Separation and characterization of lignin from bio-ethanol production residue.

PubMed

Guo, Guowan; Li, Shujun; Wang, Lu; Ren, Shixue; Fang, Guizhen

2013-05-01

In order to develop an adequate method to separate lignin from bio-ethanol production residue, solvent extraction was conducted by using benzyl alcohol, dioxane and ethanol. Compared to the conventional alkali-solution and acid-isolation method, benzyl alcohol and dioxane extraction could reach higher lignin yield of 71.55% and 74.14% respectively. FTIR and XRD analysis results indicate that sodium hydroxide solution dissolved most of the lignin in the raw material. However, the low lignin yield by this method may be attributed to the products loss during the complex separation process. GPC and (1)H NMR results revealed that the dioxane-lignin had closer molecular weight with alkali-lignin, lower S/G ratio (0.22) and higher OHPh/OHAl ratio (0.45) with respect to benzyl alcohol-lignin. The results divulge that the lignin products separated from bio-ethanol production residue by dioxane extraction had fairly potential application with better chemical activity. Copyright © 2012 Elsevier Ltd. All rights reserved.

Simultaneous Transformation of Commingled Trichloroethylene, Tetrachloroethylene, and 1,4-Dioxane by a Microbially Driven Fenton Reaction in Batch Liquid Cultures.

PubMed

Sekar, Ramanan; Taillefert, Martial; DiChristina, Thomas J

2016-11-01

Improper disposal of 1,4-dioxane and the chlorinated organic solvents trichloroethylene (TCE) and tetrachloroethylene (also known as perchloroethylene [PCE]) has resulted in widespread contamination of soil and groundwater. In the present study, a previously designed microbially driven Fenton reaction system was reconfigured to generate hydroxyl (HO˙) radicals for simultaneous transformation of source zone levels of single, binary, and ternary mixtures of TCE, PCE, and 1,4-dioxane. The reconfigured Fenton reaction system was driven by fed batch cultures of the Fe(III)-reducing facultative anaerobe Shewanella oneidensis amended with lactate, Fe(III), and contaminants and exposed to alternating anaerobic and aerobic conditions. To avoid contaminant loss due to volatility, the Fe(II)-generating, hydrogen peroxide-generating, and contaminant transformation phases of the microbially driven Fenton reaction system were separated. The reconfigured Fenton reaction system transformed TCE, PCE, and 1,4-dioxane either as single contaminants or as binary and ternary mixtures. In the presence of equimolar concentrations of PCE and TCE, the ratio of the experimentally derived rates of PCE and TCE transformation was nearly identical to the ratio of the corresponding HO˙ radical reaction rate constants. The reconfigured Fenton reaction system may be applied as an ex situ platform for simultaneous degradation of commingled TCE, PCE, and 1,4-dioxane and provides valuable information for future development of in situ remediation technologies. A microbially driven Fenton reaction system [driven by the Fe(III)-reducing facultative anaerobe S. oneidensis] was reconfigured to transform source zone levels of TCE, PCE, and 1,4-dioxane as single contaminants or as binary and ternary mixtures. The microbially driven Fenton reaction may thus be applied as an ex situ platform for simultaneous degradation of at least three (and potentially more) commingled contaminants. Additional targets for ex situ and in situ degradation by the microbially driven Fenton reaction developed in the present study include multiple combinations of environmental contaminants susceptible to attack by Fenton reaction-generated HO˙ radicals, including commingled plumes of 1,4-dioxane, pentachlorophenol (PCP), PCE, TCE, 1,1,2-trichloroethane (TCA), and perfluoroalkylated substances (PFAS). Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Simultaneous Transformation of Commingled Trichloroethylene, Tetrachloroethylene, and 1,4-Dioxane by a Microbially Driven Fenton Reaction in Batch Liquid Cultures

PubMed Central

Sekar, Ramanan; Taillefert, Martial

2016-01-01

ABSTRACT Improper disposal of 1,4-dioxane and the chlorinated organic solvents trichloroethylene (TCE) and tetrachloroethylene (also known as perchloroethylene [PCE]) has resulted in widespread contamination of soil and groundwater. In the present study, a previously designed microbially driven Fenton reaction system was reconfigured to generate hydroxyl (HO˙) radicals for simultaneous transformation of source zone levels of single, binary, and ternary mixtures of TCE, PCE, and 1,4-dioxane. The reconfigured Fenton reaction system was driven by fed batch cultures of the Fe(III)-reducing facultative anaerobe Shewanella oneidensis amended with lactate, Fe(III), and contaminants and exposed to alternating anaerobic and aerobic conditions. To avoid contaminant loss due to volatility, the Fe(II)-generating, hydrogen peroxide-generating, and contaminant transformation phases of the microbially driven Fenton reaction system were separated. The reconfigured Fenton reaction system transformed TCE, PCE, and 1,4-dioxane either as single contaminants or as binary and ternary mixtures. In the presence of equimolar concentrations of PCE and TCE, the ratio of the experimentally derived rates of PCE and TCE transformation was nearly identical to the ratio of the corresponding HO˙ radical reaction rate constants. The reconfigured Fenton reaction system may be applied as an ex situ platform for simultaneous degradation of commingled TCE, PCE, and 1,4-dioxane and provides valuable information for future development of in situ remediation technologies. IMPORTANCE A microbially driven Fenton reaction system [driven by the Fe(III)-reducing facultative anaerobe S. oneidensis] was reconfigured to transform source zone levels of TCE, PCE, and 1,4-dioxane as single contaminants or as binary and ternary mixtures. The microbially driven Fenton reaction may thus be applied as an ex situ platform for simultaneous degradation of at least three (and potentially more) commingled contaminants. Additional targets for ex situ and in situ degradation by the microbially driven Fenton reaction developed in the present study include multiple combinations of environmental contaminants susceptible to attack by Fenton reaction-generated HO˙ radicals, including commingled plumes of 1,4-dioxane, pentachlorophenol (PCP), PCE, TCE, 1,1,2-trichloroethane (TCA), and perfluoroalkylated substances (PFAS). PMID:27542932

IRIS Toxicological Review of 1,4-Dioxane (with Inhalation Update) (External Review Draft)

EPA Science Inventory

EPA is conducting a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of 1,4-Dioxane (with inhalation update) that when finalized will appear on the Integrated Risk Information System (IRIS) database.

IRIS Toxicological Review of 1,4-Dioxane (Interagency Science Consultation Draft)

EPA Science Inventory

On September 9, 2011, the Toxicological Review of 1,4-Dioxane (with inhalation update) (External Review Draft) was posted for external peer review and public comment. The Toxicological Review and charge were reviewed internally by EPA and by other federal agencies and White House...

FIELD STUDY: IN SITU OXIDATION OF 1,4-DIOXANE WITH OZONE AND HYDROGEN PEROXIDE

EPA Science Inventory

A pilot-scale field evaluation is underway to assess the effectiveness of in situ oxidation (using ozone with and without hydrogen peroxide) for remediation of 1,4-dioxane and chlorinated volatile organic compounds in groundwater at the Cooper Drum Company Superfund Site located ...

Three-component synthesis of dialkyl 2-(alkylimino-methylene)3- (2,2,5-trimethyl-4,6-dioxo-1,3-dioxan-5-yl)-succinates.

PubMed

Yavari, Issa; Zare, Hasan; Mohtat, Bita

2006-05-01

The adduct produced in the reaction between alkyl isocyanides and dialkyl acetylenedicarboxylates was trapped by 2,2,5-trimethyl-1,3-dioxane-4,6-dione (methyl Meldrum's acid), to afford highly functionalized ketenimines in good yields.

TANDEM BIS-ALDOL REACTION OF KETONES: A FACILE ONE-POT SYNTHESIS OF 1,3-DIOXANES IN AQUEOUS MEDIUM

EPA Science Inventory

A novel tandem bis-aldol reaction of ketone with paraformaldehyde catalyzed by polystyrenesulfonic acid in aqueous medium delivers 1,3-dioxanes in high yield. This one pot, operationally simple microwave-assisted synthetic protocol proceeds efficiently in water in the absence of ...

IRIS Toxicological Review of 1,4-Dioxane (with Inhalation Update) (Interagency Science Discussion Draft)

EPA Science Inventory

On September 9, 2011, the Toxicological Review of 1,4-Dioxane (inhalation) (External Review Draft) was posted for external peer review and public comment. Subsequently, the Toxicological Review and IRIS Summary were reviewed internally by EPA and by other federal agencies and Exe...

Halogen Oxygen Interactions and Disorder Modes in Pressure Frozen Complexes of 1,2-Dihaloperfluoroethanes with 1,4-Dioxane (Preprint)

DTIC Science & Technology

2007-05-17

iodoperfluoroethanes in 1:1 mixtures with 1,4-dioxane were pressure frozen in a diamond-anvil cell. Structures of cocrystal of 1,2...GPa/296 K. The cocrystal of ICF2CF2I:C4H8O2 and the 1,4-dioxane crystals are isostructural with their phases frozen by cooling; the...BrCF2CF2I:C4H8O2 cocrystal has not been reported earlier. In the structure of ICF2CF2I:C4H8O2 the –CF2-CF2-moiety is disordered about the I˙˙˙I molecular axis and

Development of a Gas Chromatography/Mass Spectrometry Method for the Analysis of the Solvent Stabilizer 1,4-Dioxane in Drinking Water

EPA Science Inventory

The solvent stabilizer 1,4-dioxane was named to the latest draft Drinking Water Contaminant Candidate List (CCL3) in February 2008 by the United States Environmental Protection Agency (USEPA). To collect occurrence data under the Unregulated Contaminant Monitoring Regulation (UC...

New Developments in 1,4 Dioxane Site Management

DTIC Science & Technology

2016-11-01

oxidation, enhanced bioremediation , site management. Unclassified Unclassified UU UL 8 David Adamson (713) 522-6300 Page Intentionally Left Blank...there was little indication that chlorinated solvent remedial efforts (e.g., chemical oxidation, enhanced bioremediation ) impacted 1,4-dioxane...oxidation may prove beneficial for subsequent biologically- based approaches, including both enhanced bioremediation and natural attenuation. FOR

IN SITU OXIDATION FIELD PILOT OF 1,4-DIOXANE AT THE COOPER DRUM SUPERFUND SITE

EPA Science Inventory

1,4-Dioxane, a solvent in paints, varnishes, lacquers, cosmetics, deodorants, cleaning and detergent preparations fluids, has attracted a lot of notice recently because its chemical analytical detection limit has recently been lowered from 50 µg/L to 1 µg/L. It is now commonly de...

Dehydration of dioxane by pervaporation using filled blend membranes of polyvinyl alcohol and sodium alginate.

PubMed

Kuila, Sunil Baran; Ray, Samit Kumar

2014-01-30

Pervaporation membranes were made by solution blending of polyvinyl alcohol (PVA) and sodium alginate (SA). Accordingly, five different blends with PVA:SA weight ratio of 75:25, 50:50, 25:75, 20:80 and 10:90 designated as PS1, PS2, PS3, PS4 and PS5, respectively, were prepared. Each of these blends was crosslinked with 2, 4 and 6 wt% glutaraldehyde and the resulting fifteen (5 × 3) membranes were used for pervaporative separation of 90 wt% dioxane in water. The membranes made from PS4 and PS5 were not stable during pervaporation experiments. Among the stable membranes PS3 membrane crosslinked with 2 wt% glutaraldehyde showed the best results for flux and selectivity. Thus, it was filled with nano size sodium montmorillonite filler and used for separation of dioxane-water mixtures over the entire concentration range of 80-99.5 wt% dioxane in water. The membranes were also characterized by mechanical properties, FTIR, SEM, DTA-TGA and XRD. Copyright © 2013 Elsevier Ltd. All rights reserved.

Accurate gas-phase structure of para-dioxane by fs Raman rotational coherence spectroscopy and ab initio calculations

NASA Astrophysics Data System (ADS)

Den, Takuya; Menzi, Samuel; Frey, Hans-Martin; Leutwyler, Samuel

2017-08-01

p-Dioxane is non-polar, hence its rotational constants cannot be determined by microwave rotational coherence spectroscopy (RCS). We perform high-resolution gas-phase rotational spectroscopy of para-dioxane-h8 and -d8 using femtosecond time-resolved Raman RCS in a gas cell at T = 293 K and in a pulsed supersonic jet at T ˜130 K. The inertial tensor of p-dioxane-h8 is strongly asymmetric, leading to a large number of asymmetry transients in its RCS spectrum. In contrast, the d8-isotopomer is a near-oblate symmetric top that exhibits a much more regular RCS spectrum with few asymmetry transients. Fitting the fs Raman RCS transients of p-dioxane-h8 to an asymmetric-top model yields the ground-state rotational constants A0 = 5084.4(5) MHz, B0 = 4684(1) MHz, C0 = 2744.7(8) MHz, and (A0 + B0)/2 = 4884.5(7) MHz (±1 σ ). The analogous values for p-dioxane-d8 are A0 = 4083(2) MHz, B0 = 3925(4) MHz, C0 = 2347.1(6) MHz, and (A0 + B0)/2 = 4002.4(6) MHz. We determine the molecular structure with a semi-experimental approach involving the highly correlated coupled-cluster singles, doubles and iterated triples method and the cc-pCVXZ basis set series from double- to quadruple-zeta (X = D, T, Q). Combining the calculated vibrationally averaged rotational constants A0c a l c(X ) ,B0c a l c(X ) ,C0c a l c(X ) for increasing basis-set size X with non-linear extrapolation to the experimental constants A0e x p,B0e x p,C0e x p allows to determine the equilibrium ground state structure of p-dioxane. For instance, the equilibrium C-C and C-O bond lengths are re(CC) = 1.5135(3) Å and re(CO) = 1.4168(4) Å, and the four axial C-H bond lengths are 0.008 Å longer than the four equatorial ones. The latter is ascribed to the trans-effect (anomeric effect), i.e., the partial delocalization of the electron lone-pairs on the O atoms that are oriented trans, relative to the axial CH bonds.

76 FR 54225 - Draft Toxicological Review of 1,4-Dioxane: In Support of Summary Information on the Integrated...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-31

.../003). New studies regarding the toxicity of 1,4-dioxane through the inhalation route of exposure are... (U.S. EPA, 2010). These studies have been incorporated into the previously posted assessment for... information). When you register, please indicate if you will need audio-visual equipment (e.g., laptop...

Concentration of 1,4-Dioxane in Wells Sampled During 2002-2009 in the Vicinity of the Tucson International Airport Area Superfund Site, Arizona

USGS Publications Warehouse

Tillman, Fred D.

2010-01-01

Extensive groundwater contamination resulting from industrial activities led to the listing of the Tucson International Airport Area as a Superfund Site in 1983. Early investigations revealed elevated levels of volatile organic compounds (VOCs) including the chlorinated solvents trichloroethylene (TCE) and perchloroethylene (PCE) in wells in the area. Several responsible parties were identified and cleanup activities were begun in the late 1980s using technology designed for removal of VOCs. In 2002, the compound 1,4-dioxane was discovered in wells in the Tucson Airport Remediation Project (TARP) area. Since then, 1,4-dioxane has been detected throughout the TARP area, in some cases exceeding the U.S. Environmental Protection Agency (USEPA) drinking water advisory level of 3 ?g/L.

Mode of interaction of 1,4-dioxane agonists at the M2 and M3 muscarinic receptor orthosteric sites.

PubMed

Del Bello, Fabio; Bonifazi, Alessandro; Quaglia, Wilma; Mazzolari, Angelica; Barocelli, Elisabetta; Bertoni, Simona; Matucci, Rosanna; Nesi, Marta; Piergentili, Alessandro; Vistoli, Giulio

2014-08-01

The methyl group in cis stereochemical relationship with the basic chain of all pentatomic cyclic analogues of ACh is crucial for the agonist activity at mAChR. Among these only cevimeline (1) is employed in the treatment of xerostomia associated with Sjögren's syndrome. Here we demonstrated that, unlike 1,3-dioxolane derivatives, in the 1,4-dioxane series the methyl group is not essential for the activation of mAChR subtypes. Docking studies, using the crystal structures of human M2 and rat M3 receptors, demonstrated that the 5-methylene group of the 1,4-dioxane nucleus of compound 10 occupies the same lipophilic pocket as the methyl group of the 1,3-dioxolane 4. Copyright © 2014 Elsevier Ltd. All rights reserved.

An Easy Student Synthesis of a Substituted 1,3-Dioxane by Use of an Ion-Exchange Resin as Catalyst: Clean Illustration of the Prins Reaction.

ERIC Educational Resources Information Center

Delmas, Michael; And Others

1982-01-01

Background information and experimental procedures are provided for a Prins reaction (condensation of an aldehyde with an alkene). The preparation of 4-(4-hydroxy, 3-methoxy-phenyl) 5-methyl, 1,3-dioxane realized from isoeugenol (natural plant product, commercially available) can be completed in a three-hour laboratory period. (Author/JN)

Structural and dipolar properties of the voltage-dependent pore former alamethicin in octanol/dioxane.

PubMed Central

Schwarz, G; Savko, P

1982-01-01

Dielectric constant and loss of the membrane-active peptide alamethicin in octanol/dioxane mixtures have been measured at frequencies between 5 kHz and 50 MHz. On the basis of a rotational mechanism of dipolar orientation, the observed dispersion provides information regarding size, shape, and dipole moment of the structural entities which the solute may assume in media of diverse lipophilicity. Particularly detailed results are obtained in a pure octanol solvent where an apparent molecular weight of alamethicin could be determined. It turns out that in this quite lipophilic medium most of the peptide material exists as a monomer particle that has approximate length and diameter of 35 and 13 A, respectively. It carries a dipole moment of approximately 75 Debye units (directed nearly parallel to the long axis). At our concentrations of a few milligrams per milliliters, appreciable formation of dimers by head-to-tail linkage is indicated. When the octanol content is reduced by adding greater amounts of dioxane, larger particles are encountered. This is accompanied by a decrease of the effective polarity. The inherent increase of hydrophilicity in the dioxane-enriched solvent apparently favors another monomer conformation that has a low dipole moment and easily aggregates to some kind of micelle. PMID:7115881

Structures, chemotaxonomic significance, cytotoxic and Na(+),K(+)-ATPase inhibitory activities of new cardenolides from Asclepias curassavica.

PubMed

Zhang, Rong-Rong; Tian, Hai-Yan; Tan, Ya-Fang; Chung, Tse-Yu; Sun, Xiao-Hui; Xia, Xue; Ye, Wen-Cai; Middleton, David A; Fedosova, Natalya; Esmann, Mikael; Tzen, Jason T C; Jiang, Ren-Wang

2014-11-28

Five new cardenolide lactates (1–5) and one new dioxane double linked cardenolide glycoside (17) along with 15 known compounds (6–16 and 18–21) were isolated from the ornamental milkweed Asclepias curassavica. Their structures were elucidated by extensive spectroscopic methods (IR, UV, MS, 1D- and 2D-NMR). The molecular structures and absolute configurations of 1–3 and 17 were further confirmed by single-crystal X-ray diffraction analysis. Simultaneous isolation of dioxane double linked cardenolide glycosides (17–21) and cardenolide lactates (1–5) provided unique chemotaxonomic markers for this genus. Compounds 1–21 were evaluated for the inhibitory activities against DU145 prostate cancer cells. The dioxane double linked cardenolide glycosides showed the most potent cytotoxic effect followed by normal cardenolides and cardenolide lactates, while the C21 steroids were non-cytotoxic. Enzymatic assay established a correlation between the cytotoxic effects in DU145 cancer cells and the Ki for the inhibition of Na(+),K(+)-ATPase. Molecular docking analysis revealed relatively strong H-bond interactions between the bottom of the binding cavity and compounds 18 or 20, and explained why the dioxane double linked cardenolide glycosides possessed higher inhibitory potency on Na(+),K(+)-ATPase than the cardenolide lactate.

Studies on Metabolism of 1,4-Dioxane

DTIC Science & Technology

2010-03-01

altered strength, and stereotypes or bizarre behavior (e.g., self mutilation, walking backwards). f. Study conduct. The study described will be...from dioxane in drinking water that is the foundation of the EPA drinking water risk assessment. V.3.3 Laboratory Animals: V.3.3.1 Genus and Species...stimuli, altered strength, and stereotypes or bizarre behavior (e.g., self mutilation, walking backwards). V.4.1.2.3 Paralytics: N/A V.4.1.3 Literature

Surface tension isotherms of the dioxane-acetone-water and glycerol-ethanol-water ternary systems

NASA Astrophysics Data System (ADS)

Dzhambulatov, R. S.; Dadashev, R. Kh.; Elimkhanov, D. Z.; Dadashev, I. N.

2016-10-01

The results of the experimental and theoretical studies of the concentration dependence of surface tension of aqueous solutions of the 1,4-dioxane-acetone-water and glycerol-ethanol-water ternary systems were given. The studies were performed by the hanging-drop method on a DSA100 tensiometer. The maximum error of surface tension was 1%. The theoretical models for calculating the surface tension of the ternary systems of organic solutions were analyzed.

Comparison of Sampling Probe and Thermal Desorber in Hazardous Air Pollutants on Site (HAPSITE) Extended Range (ER) for Analysis of Toxic Organic (TO)-15 Compounds

DTIC Science & Technology

2014-03-01

641,000 671,667 1,4‐dioxane  88  2.20 101 154,000 160,000 137,000 150,333 105,000  119,000 113,000 112,333 Trichloroethylene   130  2.20 87 412,000...Bromodichloromethane 14-dioxane Trichloroethylene Heptane (Z)-13-Dichloro-1-propene Methyl Isobutyl Ketone (E)-13-Dichloro-1-propene 112

Liquid Crystalline Polymers Containing Heterocycloalkane Mesogens. 1. Side-Chain Liquid Crystalline Polymethacrylates and Polycrylates Containing 2,5-Disubstituted-1,3-Dioxane Mesogens.

DTIC Science & Technology

1986-10-01

Report No. 2 Liquid Crystalline Polymers Containing Heterocycloalkane Mesogeus 1. Side-Chain Liquid Crystalline Polymethacrylates and . Polyacrylates...8217. " "-"-"-" " "" ’CS" i Liquid Crystalline Polymers Containing Heterocycloalkane Mesogens 1. Side-Chain Liquid Crystalline Polymethacrylates and Polyacrylates...University Cleveland, OH 44106 ABSTRACT Polymethacrylates and polyacrylates containing 2-(p-hydroxyphenyl)-5-(p-meth- oxyphenyl)-1,3-dioxane as a

In Situ Bioremediation of 1,4-Dioxane by Methane Oxidizing Bacteria in Coupled Anaerobic-Aerobic Zones

DTIC Science & Technology

2016-02-11

groundwater in situ. Because of its low Koc and Henry’s Law constant, traditional remediation technologies such as carbon adsorption and air stripping...of 1,4-dioxane via methane oxidizing bacteria is of particular interest for in situ remedial purposes for two reasons. (1) Cometabolic mechanisms...2010. Final Remedial Action Report: Building 165 and Area 18C Groundwater Treatment Pilot Systems; Former Raritan Arsenal Project, Edison, NJ. US

Neutron scattering of residual hydrogen in 1,4-dioxane d 8 liquid: Understanding measurements with molecular dynamics simulations

DOE PAGES

Liu, Hongjun; Herwig, Kenneth W.; Kidder, Michelle K.; ...

2016-06-08

That incoherent scattering from protiated molecular liquids adds a constant background to the measured scattering intensity is well-known, but less appreciated is the fact that coherent scattering is also induced by the presence of hydrogen in a deuterated liquid. In fact, the scattering intensity can be very sensitive, in the small-q region, with respect to the amounts and distribution of residual H in the system. We used 1,4-dioxane liquid to demonstrate that the partial structure factors of the HD and DD atom pairs contribute significantly to intermolecular scattering and that uncertainty in the extent of deuteration account for discrepancies betweenmore » simulations and measurements. Both contributions to uncertainty have similar magnitudes: scattering interference of the hydrogen–deuterium pair, and complementary interference from the deuterium–deuterium pair by virtue of chemical inhomogeneity. This situation arises in practice since deuteration of liquids is often 99% or less. A combined experimental and extensive computational study of static thermal neutron scattering of 1,4-dioxane demonstrates the foregoing. We show, through simulations, that the reason for the differences is the content of protiated dioxane (vendors quote 1%). We estimate that up to 5% (at 298 K and at 343 K) protiated molar fraction may be involved in generating the scattering differences. Finally, we find that the particular distribution of hydrogen in the protiated molecules affects the results significantly; here, we considered molecules to be either fully protiated or fully deuterated. This scenario best reconciles the computational and experimental results, and leads us to speculate that the deuteration synthesis process tends to leave a molecule either fully deuterated or fully protiated. As a result, we have used 1,4-dioxane as a model liquid, the effects described in this study extend to similar liquids, and similar systematic experimental/computational studies can be performed to either understand measurements or calibrate/validate molecular dynamics models.« less

Viscosity of nonelectrolyte liquid mixtures. IV. Binary mixtures containing p-Dioxane

NASA Astrophysics Data System (ADS)

Oswal, S. L.; Oswal, P.; Phalak, R. P.

1996-11-01

Measurements of the viscosity η and density p are reported for eight binary mixtures of p-dioxane with methylcyclohexane, l-chlorohexane, l-bromohexane, p-xylene, propylbenzene, methyl acetate, butyl acetate. anyl acetate at 303.15 K. The viscosity data haw been correlated with the equations of Grunbeng Nissan. of McAllister, and of Auslaendcr. The relation among the excess viscosity Δ In η, excess Gibbs energy of activation ΔG* E of viscous flow. and intermolecular interaction in these mixtures is discussed.

Effect of dioxane on the benzil:SDS radical pair system. A study in the presence of high magnetic fields

NASA Astrophysics Data System (ADS)

Misra, Ajay; Dutta, Rina; Chowdhury, Mihir

1995-09-01

The magnetic response of the radical pair generated by the hydrogen abstraction of the photoexcited benzil triplet from sodium dodecyl sulphate is studied. It is found that radical decay curves, with or without magnetic field, are affected on addition of small amphiphiles such as 1,4-dioxane. The results have been interpreted on the basis of the ability of the latter to change the micellar aggregation number and intramicellar viscosity.

Electronic spectra and DFT calculations of some pyrimido[1,2-a]benzimidazole derivatives

NASA Astrophysics Data System (ADS)

Elshakre, Mohamed E.; Moustafa, H.; Hassaneen, Huwaida. M. E.; Moussa, Abdelrahim. Z.

2015-06-01

Ground state properties of 2,4-diphenyl-1,4-dihydrobenzo[4,5]imidazo[1,2-a]pyrimidine, compound 1, and its derivatives are investigated experimentally and theoretically in Dioxane and DMF. The calculations show that all the studied compounds (1-7) are non-planar, resulting in a significant impact on the electronic and structural properties. The ground state properties of compounds 1-7 at B3LYP/6-311G (d, p) show that compound 5 has the lowest EHOMO, ELUMO, and ΔE indicating highest reactivity. Compound 7 is found to have the highest polarity. The observed UV spectra in Dioxane and DMF of compounds 1-4 show 2 bands, while compounds 5-7 show 4 bands in both solvents. Band maxima (λmax) and intensities of the spectra are found to have solvent dependence reflected as blue and red shifts. The theoretical spectra computed at TD-B3LYP/6-311G (d, p) in gas phase, Dioxane and DMF indicate a good agreement with the observed spectra.

Odor Events in Surface and Treated Water: The Case of 1,3-Dioxane Related Compounds.

PubMed

Quintana, Jordi; Vegué, Lídia; Martín-Alonso, Jordi; Paraira, Miquel; Boleda, M Rosa; Ventura, Francesc

2016-01-05

A study has been carried out to identify the origin of the odorous compounds at trace levels detected in surface waters and in Barcelona's tap water (NE Spain) which caused consumer complaints. The malodorous compounds were 2,5,5-trimethyl-1,3-dioxane (TMD) and 2-ethyl-5,5-dimethyl-1,3-dioxane (2EDD) which impart a distinctive sickening or olive-oil odor to drinking water at low ng/L levels. Flavor profile analysis (FPA) or threshold odor number (TON) were used for organoleptic purposes. Levels up to 749 ng/L for TMD and 658 ng/L for 2EDD were measured at the entrance of the drinking water treatment plant. Three wastewater treatment plants (WWTPs) using industrial byproducts coming from resin manufacturing plants to promote codigestion were found to be the origin of the event. Corrective measures were applied, including the prohibition to use these byproducts for codigestion in the WWTPs involved. A similar event was already recorded in the same area 20 years ago.

Studies on the self-catalyzed Knoevenagel condensation, characterization, DPPH radical scavenging activity, cytotoxicity, and molecular properties of 5-arylidene-2,2-dimethyl-1,3-dioxane-4,6-diones using single crystal XRD and DFT techniques

NASA Astrophysics Data System (ADS)

Suresh Kumar, G. S.; Antony Muthu Prabhu, A.; Bhuvanesh, N.

2014-10-01

We have studied the self-catalyzed Knoevenagel condensation, spectral characterization, DPPH radical scavenging activity, cytotoxicity, and molecular properties of 5-arylidene-2,2-dimethyl-1,3-dioxane-4,6-diones using single crystal XRD and DFT techniques. In the absence of any catalyst, a series of novel 5-arylidene-2,2-dimethyl-1,3-dioxane-4,6-diones were synthesized using Meldrum’s acid and formylphenoxyaliphatic acid(s) in water. These molecules are arranged in the dimer form through intermolecular H-bonding in the single crystal XRD structure. Compounds have better DPPH radical scavenging activity and cytotoxicity against A431 cancer cell line. The optimized molecular structure, natural bond orbital analysis, electrostatic potential map, HOMO-LUMO energies, molecular properties, and atomic charges of these molecules have been studied by performing DFT/B3LYP/3-21G(*) level of theory in gas phase.

Computer simulation of the linear and nonlinear optical susceptibilities of p-nitroaniline in cyclohexane, 1,4-dioxane, and tetrahydrofuran in quadrupolar approximation. II. Local field effects and optical susceptibilitities.

PubMed

Reis, H; Papadopoulos, M G; Grzybowski, A

2006-09-21

This is the second part of a study to elucidate the local field effects on the nonlinear optical properties of p-nitroaniline (pNA) in three solvents of different multipolar character, that is, cyclohexane (CH), 1,4-dioxane (DI), and tetrahydrofuran (THF), employing a discrete description of the solutions. By the use of liquid structure information from molecular dynamics simulations and molecular properties computed by high-level ab initio methods, the local field and local field gradients on p-nitroaniline and the solvent molecules are computed in quadrupolar approximation. To validate the simulations and the induction model, static and dynamic (non)linear properties of the pure solvents are also computed. With the exception of the static dielectric constant of pure THF, a good agreement between computed and experimental refractive indices, dielectric constants, and third harmonic generation signals is obtained for the solvents. For the solutions, it is found that multipole moments up to two orders higher than quadrupole have a negligible influence on the local fields on pNA, if a simple distribution model is employed for the electric properties of pNA. Quadrupole effects are found to be nonnegligible in all three solvents but are especially pronounced in the 1,4-dioxane solvent, in which the local fields are similar to those in THF, although the dielectric constant of DI is 2.2 and that of the simulated THF is 5.4. The electric-field-induced second harmonic generation (EFISH) signal and the hyper-Rayleigh scattering signal of pNA in the solutions computed with the local field are in good to fair agreement with available experimental results. This confirms the effect of the "dioxane anomaly" also on nonlinear optical properties. Predictions based on an ellipsoidal Onsager model as applied by experimentalists are in very good agreement with the discrete model predictions. This is in contrast to a recent discrete reaction field calculation of pNA in 1,4-dioxane, which found that the predicted first hyperpolarizability of pNA deviated strongly from the predictions obtained using Onsager-Lorentz local field factors.

Strong impact of the solvent on the photokinetics of a 2(1H)-pyrimidinone.

PubMed

Ryseck, G; Villnow, T; Hugenbruch, S; Schaper, K; Gilch, P

2013-08-01

Pyrimidinones are part of the (6-4) photolesions which may be formed from two pyrimidine bases adjacent on a DNA strand. In relation to the secondary photochemistry of the (6-4) lesion, i.e. its transformation into a Dewar valence isomer, photophysical and photochemical properties of 1-methyl-2(1H)-pyrimidinone (1MP) in water, acetonitrile, methanol, and 1,4-dioxane are reported here. As deduced from steady state fluorescence and femtosecond transient absorption spectroscopy the S1 lifetime of 1MP is strongly affected by the solvent. The lifetimes range from 400 ps for water to 40 ps for 1,4-dioxane. Internal conversion (IC) and intersystem crossing (ISC) contribute to the S1 decay. The solvent effect on the IC rate constant is more pronounced than on the ISC constant. The quantum yields for the consumption of 1MP (values for nitrogen purged solvents) are large for methanol (0.35) and 1,4-dioxane (0.24) and small for acetonitrile (0.02) and water (0.003). Hydrogen abstraction from the solvent by the triplet state of 1MP may rationalize this.

Organosolv extraction of lignin from hydrolyzed almond shells and application of the delta-value theory.

PubMed

Quesada-Medina, Joaquín; López-Cremades, Francisco Javier; Olivares-Carrillo, Pilar

2010-11-01

The solubility of lignin from hydrolyzed almond (Prunus amygdalus) shells in different acetone, ethanol and dioxane-water mixtures and conditions (extraction time and temperature) was studied. The concept of the solubility parameter (delta-value) was applied to explain the effect of organic solvent concentration on lignin solubility. The organic solvent-water mixture that led to the highest lignin extraction was composed of a 75% vol. of organic solvent for all the solvent series investigated (acetone, ethanol and dioxane). Moreover, the best lignin extraction conditions were a temperature of 210 degrees C and an extraction time of 40 min for the acetone and ethanol series, and 25 min for the dioxane series. The delta-value of the hydrolyzed almond shell lignin [14.60 (cal/cm(3))(1/2)] and that of the organic solvent-water mixtures was calculated. The experimental delignification capacity of the aqueous organic solvents clearly reflected the proximity of their delta-value to that of lignin. The hydrogen-bonding capacity of the solvent-water mixtures was also taken into account. Copyright 2010 Elsevier Ltd. All rights reserved.

Electrooxidation of industrial wastewater containing 1,4-dioxane in the presence of different salts.

PubMed

Barndõk, H; Hermosilla, D; Cortijo, L; Torres, E; Blanco, A

2014-04-01

The treatment of 1,4-dioxane solution by electrochemical oxidation on boron-doped diamond was studied using a central composite design and the response surface methodology to investigate the use of SO4 (2-) and HCO3 (-) as supporting electrolytes considering the applied electric current, initial chemical oxygen demand (COD) value, and treatment time. Two industrial effluents containing bicarbonate alkalinity, one just carrying 1,4-dioxane (S1), and another one including 1,4-dioxane and 2-methyl-1,3-dioxolane (S2), were treated under optimized conditions and subsequently subjected to biodegradability assays with a Pseudomonas putida culture. Electrooxidation was compared with ozone oxidation (O3) and its combination with hydrogen peroxide (O3/H2O2). Regarding the experimental design, the optimal compromise for maximum COD removal at minimum energy consumption was shown at the maximum tested concentrations of SO4 (2-) and HCO3 (-) (41.6 and 32.8 mEq L(-1), respectively) and the maximum selected initial COD (750 mg L(-1)), applying a current density of 11.9 mA cm(-2) for 3.8 h. Up to 98 % of the COD was removed in the electrooxidation treatment of S1 effluent using 114 kWh per kg of removed COD and about 91 % of the COD from S2 wastewater applying 49 kWh per kg of removed COD. The optimal biodegradability enhancement was achieved after 1 h of electrooxidation treatment. In comparison with O3 and O3/H2O2 alternatives, electrochemical oxidation achieved the fastest degradation rate per oxidant consumption unit, and it also resulted to be the most economical treatment in terms of energy consumption and price per unit of removed COD.

Stoichiometric determination of moisture in edible oils by Mid-FTIR spectroscopy.

PubMed

van de Voort, F R; Tavassoli-Kafrani, M H; Curtis, J M

2016-04-28

A simple and accurate method for the determination of moisture in edible oils by differential FTIR spectroscopy has been devised based on the stoichiometric reaction of the moisture in oil with toluenesulfonyl isocyanate (TSI) to produce CO2. Calibration standards were devised by gravimetrically spiking dry dioxane with water, followed by the addition of neat TSI and examination of the differential spectra relative to the dry dioxane. In the method, CO2 peak area changes are measured at 2335 cm(-1) and were shown to be related to the amount of moisture added, with any CO2 inherent to residual moisture in the dry dioxane subtracted ratioed out. CO2 volatility issues were determined to be minimal, with the overall SD of dioxane calibrations being ∼18 ppm over a range of 0-1000 ppm. Gravimetrically blended dry and water-saturated oils analysed in a similar manner produced linear CO2 responses with SD's of <15 ppm on average. One set of dry-wet blends was analysed in duplicate by FTIR and by two independent laboratories using coulometric Karl Fischer (KF) procedures. All 3 methods produced highly linear moisture relationships with SD's of 7, 16 and 28 ppm, respectively over a range of 200-1500 ppm. Although the absolute moisture values obtained by each method did not exactly coincide, each tracked the expected moisture changes proportionately. The FTIRTSI-H2O method provides a simple and accurate instrumental means of determining moisture in oils rivaling the accuracy and specificity of standard KF procedures and has the potential to be automated. It could also be applied to other hydrophobic matrices and possibly evolve into a more generalized method, if combined with polar aprotic solvent extraction. Copyright © 2016 Elsevier B.V. All rights reserved.

Zwitterionic and free forms of arylmethyl Meldrum's acids.

PubMed

Mierina, Inese; Mishnev, Anatoly; Jure, Mara

2015-09-01

C-Alkyl (including C-arylmethyl) derivatives of Meldrum's acids are attractive building blocks in organic synthesis, mainly due to the unusually high acidity of the resulting compounds. Three examples, namely 5-[4-(diethylamino)benzyl]-2,2-dimethyl-1,3-dioxane-4,6-dione, C17H23NO4, (I), 2,2-dimethyl-5-(2,4,6-trimethoxybenzyl)-1,3-dioxane-4,6-dione, C16H20O7, (II), and 5-(4-hydroxy-3,5-dimethoxybenzyl)-2,2-dimethyl-1,3-dioxane-4,6-dione, C15H18O7, (III), have been synthesized, characterized by NMR and IR spectroscopy, and studied by single-crystal X-ray structure analysis. The nature of the different substituents resulted in remarkable differences in both the molecular conformations and the crystal packing arrangements. The presence of a substituent with a basic centre in compound (I) leads to the formation of an inner salt accompanied by drastic changes in the conformation of the 1,3-dioxane-4,6-dione fragment. By virtue of strong N-H···O hydrogen bonds, the residues are assembled into infinite chains with the graph-set descriptor C(10). Compound (II) contains methoxy groups in both the ortho- and para-positions of the arylmethyl fragment. Because of the absence of classical hydrogen-bond donors in this structure, the crystal packing is controlled by van der Waals forces and weak C-H···O interactions. Compound (III) contains methoxy groups in both meta-positions and a hydroxy group in the para-position. Supramolecular tetrameric synthons which comprise hydrogen-bonded dimers associated into tetramers through π-π interactions of overlapping benzene rings were observed.

5-Arylidene derivatives of Meldrum's acid: Synthesis, structural characterization using single crystal and powder crystal X-ray diffraction, and electronic properties

NASA Astrophysics Data System (ADS)

Dey, Tanusri; Ghosh, Soumen; Ghosh, Somnath; Mukherjee, Alok Kumar

2015-07-01

Four 5-arylidene derivatives of Meldrum's acid, 5-(4-chlorobenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (2), 5-(3-hydroxybenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (3), 5-(3,4-dimethoxybenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (4) and 5-(2,4-dimethoxy benzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (5) have been synthesized and their crystal structures have been determined using single crystal X-ray diffractometry for 2, 4 and 5 and X-ray powder diffraction for 3. The nature of intermolecular interactions in 2-5 has been analyzed through Hirshfeld surfaces and 2D fingerprint plots. The DFT optimized molecular geometries in 2-5 agree closely with those obtained from the crystallographic studies. The crystal packing in 2-5 exhibits an interplay of Osbnd H⋯O, Csbnd H⋯O, Csbnd H⋯Cl and Csbnd H⋯π (arene) hydrogen bonds and π⋯π interactions, which assemble molecules into three-dimensional architecture in 2, 3 and 5 and two-dimensional framework in 4. The Hirshfeld surface analyses of 2-5, Meldrum's acid (1) and a few related 5-arylidene derivatives of Meldrum's acid retrieved from the Cambridge Structural Database (CSD) indicate that about 85% of the Hirshfeld surface area (72% in 2 where H⋯Cl contribution is about 13%) in this class of compounds are due to H⋯H, O⋯H and C⋯H contacts. The HOMO-LUMO energy gap (>2.2 eV) in 2-5 indicates a significant degree of internal charge transfer within the molecule.

Improved tolerance to off-resonance in spectral-spatial EPI of hyperpolarized [1-13 C]pyruvate and metabolites.

PubMed

Lau, Justin Y C; Geraghty, Benjamin J; Chen, Albert P; Cunningham, Charles H

2018-09-01

For 13 C echo-planar imaging (EPI) with spectral-spatial excitation, main field inhomogeneity can result in reduced flip angle and spatial artifacts. A hybrid time-resolved pulse sequence, multi-echo spectral-spatial EPI, is proposed combining broader spectral-spatial passbands for greater off-resonance tolerance with a multi-echo acquisition to separate signals from potentially co-excited resonances. The performance of the imaging sequence and the reconstruction pipeline were evaluated for 1 H imaging using a series of increasingly dilute 1,4-dioxane solutions and for 13 C imaging using an ethylene glycol phantom. Hyperpolarized [1- 13 C]pyruvate was administered to two healthy rats. Multi-echo data of the rat kidneys were acquired to test realistic cases of off-resonance. Analysis of separated images of water and 1,4-dioxane following multi-echo signal decomposition showed water-to-dioxane 1 H signal ratios that were in agreement with the independent measurements by 1 H spectroscopy for all four concentrations of 1,4-dioxane. The 13 C signal ratio of two co-excited resonances of ethylene glycol was accurately recovered after correction for the spectral profile of the redesigned spectral-spatial pulse. In vivo, successful separation of lactate and pyruvate-hydrate signals was achieved for all except the early time points during which signal variations exceeded the temporal resolution of the multi-echo acquisition. Improved tolerance to off-resonance in the new 13 C data acquisition pipeline was demonstrated in vitro and in vivo. Magn Reson Med 80:925-934, 2018. © 2018 International Society for Magnetic Resonance in Medicine. © 2018 International Society for Magnetic Resonance in Medicine.

Determining the Residual Characteristics of Alkylphenols, Arsenic, and Lead as well as Assessing the Exposures of 1,4-Dioxane from Household Food Detergents.

PubMed

Lin, Wan-Ting; Chen, Wun-Ling; Cheng, Wei-Chih; Chang, Hui-Chuan; Tsai, Shih-Wei

2017-07-01

Food detergents are commonly used in households. The main components of detergents include surfactants and water. It has been found that certain compounds, which may cause health concerns, appear in food detergents, such as alkylphenols, arsenic, and lead. After applying food detergents is when people may be exposed to various levels of these chemicals when there are residues. In this study, the Taguchi experimental design was performed to determine the possible factors that might affect the residual characteristics of food detergent on dishware, fruits, and vegetables. The results showed that the variety of detergent was found to be the most significant factor affecting the residue amounts of arsenic (62.9%) and lead (71.6%) on fruits and vegetables, whereas the concentration of detergent used affected the amount of lead residue only (10.5%). On the other hand, dishware material, the concentration of analytes, immersion time, and type of surfactant contributed to arsenic residues on dishware, whereas technical nonylphenol isomer residues on dishware increased as the concentration of spiked analyte increased. In addition, the occurrence of 1,4-dioxane, a possible human carcinogen, in household food detergents in Taiwan was also determined in this research by solid-phase microextraction and GC-MS. Among the 80 detergent samples, 71 contained different concentrations ranges of 1,4-dioxane, from 0.03 to ~3.73 µg/g. In the exposure assessment, it was estimated that the maximum amounts of 1,4-dioxane in contact with the skin from the use of household food detergent in Taiwan was 0.015 µg/kg/day.

2-(Maleimidomethyl)-1,3-Dioxanes (MD): a Serum-Stable Self-hydrolysable Hydrophilic Alternative to Classical Maleimide Conjugation

NASA Astrophysics Data System (ADS)

Dovgan, Igor; Kolodych, Sergii; Koniev, Oleksandr; Wagner, Alain

2016-08-01

The vast majority of antibody-drug conjugates (ADC) are prepared through amine-to-thiol conjugation. To date, N-Succinimidyl-4-(maleimidomethyl) cyclohexanecarboxylate (SMCC) has been one of the most frequently applied reagents for the preparation of ADC and other functional conjugates. However, SMCC-based conjugates suffer from limited stability in blood circulation and from a hydrophobic character of the linker, which may give rise to major pharmacokinetic implications. To address this issue, we have developed a heterobifunctional analogue of a SMCC reagent, i.e., sodium 4-(maleimidomethyl)-1,3-dioxane-5-carbonyl)oxy)-2,3,5,6- tetrafluorobenzenesulfonate (MDTF) for amine-to-thiol conjugation. By replacing the cyclohexyl ring in the SMCC structure with the 1,3-dioxane, we increased the hydrophilicity of the linker. A FRET probe based on MD linker was prepared and showed superior stability compared to the MCC linker in human plasma, as well as in a variety of aqueous buffers. A detailed investigation demonstrated an accelerated succinimide ring opening for MD linker, resulting in stabilized conjugates. Finally, the MDTF reagent was applied for the preparation of serum stable antibody-dye conjugate.

Investigating lipids as a source of chemical exchange-induced MRI frequency shifts.

PubMed

Shmueli, K; Dodd, S J; van Gelderen, P; Duyn, J H

2017-04-01

While magnetic susceptibility is a major contributor to NMR resonance frequency variations in the human brain, a substantial contribution may come from the chemical exchange of protons between water and other molecules. Exchange-induced frequency shifts f e have been measured in tissue and protein solutions, but relatively lipid-rich white matter (WM) has a larger f e than gray matter, suggesting that lipids could contribute. Galactocerebrosides (GC) are a prime candidate as they are abundant in WM and susceptible to exchange. To investigate this, f e was measured in a model of WM lipid membranes in the form of multilamellar vesicles (MLVs), consisting of a 1:2 molar ratio of GC and phospholipids (POPC), and in MLVs with POPC only. Chemical shift imaging with 15% volume fraction of dioxane, an internal reference whose protons are assumed not to undergo chemical exchange, was used to remove susceptibility-induced frequency shifts in an attempt to measure f e in MLVs at several lipid concentrations. Initial analysis of these measurements indicated a necessity to correct for small unexpected variations in dioxane concentration due to its effect on the water frequency shift. To achieve this, the actual dioxane concentration was inferred from spectral analysis and its additional contribution to f e was removed through separate experiments which showed that the water-dioxane frequency shift depended linearly on the dioxane concentration at low concentrations with a proportionality constant of -0.021 ± 0.002 ppb/mM in agreement with published experiments. Contrary to expectations and uncorrected results, for GC + POPC vesicles, the dependence of the corrected f e on GC concentration was insignificant (0.023 ± 0.037 ppb/mM; r 2  = 0.085, p > 0.57), whereas for the POPC-only vesicles a small but significant linear increase with POPC concentration was found: 0.044 ± 0.008 ppb/mM (r 2  = 0.877, p < 0.01). These findings suggest that the exchange-induced contribution of lipids to frequency contrast in WM may be small. Published 2016. This article is a U.S. Government work and is in the public domain in the USA. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

Spectroscopic methods for aqueous cyclodextrin inclusion complex binding measurement for 1,4-dioxane, chlorinated co-contaminants, and ozone

NASA Astrophysics Data System (ADS)

Khan, Naima A.; Johnson, Michael D.; Carroll, Kenneth C.

2018-03-01

Recalcitrant organic contaminants, such as 1,4-dioxane, typically require advanced oxidation process (AOP) oxidants, such as ozone (O3), for their complete mineralization during water treatment. Unfortunately, the use of AOPs can be limited by these oxidants' relatively high reactivities and short half-lives. These drawbacks can be minimized by partial encapsulation of the oxidants within a cyclodextrin cavity to form inclusion complexes. We determined the inclusion complexes of O3 and three common co-contaminants (trichloroethene, 1,1,1-trichloroethane, and 1,4-dioxane) as guest compounds within hydroxypropyl-β-cyclodextrin. Both direct (ultraviolet or UV) and competitive (fluorescence changes with 6-p-toluidine-2-naphthalenesulfonic acid as the probe) methods were used, which gave comparable results for the inclusion constants of these species. Impacts of changing pH and NaCl concentrations were also assessed. Binding constants increased with pH and with ionic strength, which was attributed to variations in guest compound solubility. The results illustrate the versatility of cyclodextrins for inclusion complexation with various types of compounds, binding measurement methods are applicable to a wide range of applications, and have implications for both extraction of contaminants and delivery of reagents for treatment of contaminants in wastewater or contaminated groundwater.

Specific radioisotopic assay for cholinesterase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Talbot, B.G.; Anderson, D.R.; Harris, L.W.

1992-02-01

The authors have developed a radiometric method (1) for measuring cholinesterase (ChE) activity that uses 0.4 N perchloric acid (PCA), instead of p-dioxane (method 2), to denature the ChE and stop hydrolysis of acetyl-1-{sup 14}C-choline (ACh). The unreacted ACh is removed by IRP-69 cationic exchange resin suspended in water, instead of dioxane. The supernatant containing the hydrolysis product, {sup 14}C-acetic acid, is mixed with nonhazardous scintillation cocktail and counted. The incubation mixture of 1 is similar to 2 and contains 0.1 ml of buffer-salt solution 0.1 ml of guinea pig whole blood (WB)-water suspension and 0.1 ml of 3 mMmore » ACh solution. Procedures 1 and 2 were compared to a titragraphic assay for ChE activity; specific activity values of WB (mmol ACh hydrolyzed/ml/hr) were found to be 137.6, 72.4 and 135.0, respectively. When {sup 14}C-acetic acid was processed through procedures 1 and 2, significantly less {sup 14}C was found in the supernatant from 2, whereas all of the expected {sup 14}C was found in the supernatant from 1, suggesting that IRP-69 resin in dioxane will remove significant amounts of {sup 14}C-acetic acid.« less

Relationship between the catalytic properties of the products of the oxidative thermolysis of certain complexes and the porous structures of samples in the oxidation reactions of volatile organic compounds

NASA Astrophysics Data System (ADS)

Semushina, Yu. P.; Pechenyuk, S. I.; Kuzmich, L. F.; Knyazeva, A. I.

2017-01-01

The rate of the gas-phase oxidation of ethanol, 2-propanol, acetone, ethyl acetate, dioxane, and benzene with atmospheric oxygen is studied on surfaces of bimetallic oxide catalysts Co-Fe, Cu-Fe, Cr-Co, and Ni-Fe, prepared via thermal decomposition of double complex compounds in air. It is found that the rate of oxidation of volatile compounds depends on the volume of the transient pores in the catalyst sample. The rate of oxidation on the same catalyst at 350°C depends on the nature of the substance in the order: acetone > ethyl acetate > ethanol > propanol > dioxane, benzene.

Crystal structure of 1-methyl-3-([2,2-dimethyl-4,6-dioxo-1,3-dioxane-5-ylidene]methyl)urea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habibi, A., E-mail: habibi@khu.ac.ir; Ghorbani, H. S.; Bruno, G.

2013-12-15

The crystal structure of 1-Methyl-3-([2,2-dimethyl-4,6-dioxo-1,3-dioxane-5-ylidene]methyl)urea (C{sub 9}H{sub 12}N{sub 2}O{sub 5}) has been determined by single crystal X-ray diffraction analysis. The crystals are monoclinic, a = 5.3179(2), b = 18.6394(6), c =10.8124(3) Å, β = 100.015(2)°, Z = 4, sp. gr. P2{sub 1}/c, R = 0.0381 for 2537 reflections with I > 2σ(I). Except for C(CH{sub 3}){sub 2} group, the molecule is planar. The structure is stabilized by inter- and intramolecular N-H...O hydrogen bonds and weak C-H...O interactions.

Field note: irrigation of tree stands with groundwater containing 1,4-dioxane.

PubMed

Ferro, Ari M; Tammi, Carl E

2009-07-01

Coniferous and deciduous tree stands totaling 14 ha were recently planted on a closed landfill, and when mature, the stands are expected to be part of a natural treatment system for recovered groundwater. The trees would be irrigated at the rate of 189 L/min year-round with water containing 1,4-dioxane (< 10 mg/L), a compound that would be taken up and phytovolatilized by the trees. The water is moderately saline and contains elevated levels of manganese. This paper describes a concurrent series of preliminary studies, performed prior to the full-scale planting, to assess the feasibility of the phytoremediation system. Greenhouse experiments were carried out to identify tree species that can take up 1,4-dioxane and are tolerant of the water. Estimates were made of the area of the tree stand necessary to transpire the irrigation water plus precipitation. The landfill matrix was characterized in terms of its percolation rate and water holding capacity and based on those results salinity-modeling studies were carried out to estimate the fate and leaching potential of the various inorganic species that would accumulate in the root-zone of the trees. A pilot study, currently in progress on the landfill, suggested that the landfill cap is a suitable matrix for the establishment of large trees, and that the stands could be irrigated without the production of excess drainage.

40 CFR 414.70 - Applicability; description of the bulk organic chemicals subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Monomethyl Ether *Dimer Acids Dioxane Ethane Ethylene Glycol Monophenyl Ether *Ethoxylates, Misc. Ethylene Glycol Dimethyl Ether Ethylene Glycol Monobutyl Ether Ethylene Glycol Monoethyl Ether Ethylene Glycol...

Specific radioisotopic assay for cholinesterase. Technical report, December 1987-March 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Talbot, B.G.; Anderson, D.R.; Harris, L.W.

1990-05-01

The radiometric method (I) for measuring ChE activity was modified to preclude the use of p-dioxane, a hazardous material. The modified procedure (II) uses 0.4 N perchloric acid (PCA), instead of p-dioxane, to denature the ChE and stop hydrolysis of 14C-acetylcholine (ACh). The unreacted substrate (ACh) is removed by cationic exchange resin suspended in water. The supernatant (acidic water solution) containing the product of hydrolysis, 14C-acetic acid, is mixed with nonhazardous scintillation cocktail and counted. The incubation mixture (37 degrees C) for II is similar to I and is composed of 0.1 ml of buffer-salt solution (pH 7.8), 0.1 mlmore » of guinea pig whole blood (WB)-water suspension and 0.1 ml of 3mM ACh solution.« less

40 CFR Table 9 to Subpart Ffff of... - Soluble Hazardous Air Pollutants

Code of Federal Regulations, 2010 CFR

2010-07-01

... sulfate 77781 6. Dinitrotoluene (2,4) 121142 7. Dioxane (1,4) 123911 8. Ethylene glycol dimethyl ether 110714 9. Ethylene glycol monobutyl ether acetate 112072 10. Ethylene glycol monomethyl ether acetate...

21 CFR 172.736 - Glycerides and polyglycides of hydrogenated vegetable oils.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., not greater than 1 mg/kg, as determined by a gas chromatographic method entitled “Determination of Ethylene Oxide and 1,4-Dioxane by Headspace Gas Chromatography,” approved November 5, 1998, printed by...

21 CFR 172.736 - Glycerides and polyglycides of hydrogenated vegetable oils.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., not greater than 1 mg/kg, as determined by a gas chromatographic method entitled “Determination of Ethylene Oxide and 1,4-Dioxane by Headspace Gas Chromatography,” approved November 5, 1998, printed by...

21 CFR 172.736 - Glycerides and polyglycides of hydrogenated vegetable oils.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., not greater than 1 mg/kg, as determined by a gas chromatographic method entitled “Determination of Ethylene Oxide and 1,4-Dioxane by Headspace Gas Chromatography,” approved November 5, 1998, printed by...

21 CFR 172.736 - Glycerides and polyglycides of hydrogenated vegetable oils.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., not greater than 1 mg/kg, as determined by a gas chromatographic method entitled “Determination of Ethylene Oxide and 1,4-Dioxane by Headspace Gas Chromatography,” approved November 5, 1998, printed by...

21 CFR 172.736 - Glycerides and polyglycides of hydrogenated vegetable oils.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., not greater than 1 mg/kg, as determined by a gas chromatographic method entitled “Determination of Ethylene Oxide and 1,4-Dioxane by Headspace Gas Chromatography,” approved November 5, 1998, printed by...

40 CFR Table 8 to Subpart Ffff of... - Soluble Hazardous Air Pollutants

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Dinitrotoluene (2,4) 121142 7. Dioxane (1,4) 123911 8. Ethylene glycol dimethyl ether 110714 9. Ethylene glycol monobutyl ether acetate 112072 10. Ethylene glycol monomethyl ether acetate 110496 11. Isophorone 78591 12...

The solvation of L-serine in mixtures of water with some aprotic solvents at 298.15 K

NASA Astrophysics Data System (ADS)

Mezhevoi, I. N.; Badelin, V. G.

2009-03-01

The integral enthalpies of solution Δsol H m of L-serine in mixtures of water with acetonitrile, 1,4-dioxane, dimethylsulfoxide (DMSO), and acetone were measured by solution calorimetry at organic component concentrations up to 0.31 mole fractions. The standard enthalpies of solution (Δsol H°), transfer (Δtr H°), and solvation (Δsolv H°) of L-serine from water into mixed solvents were calculated. The dependences of Δsol H°, Δsolv H°, and Δtr H° on the composition of aqueous-organic solvents contained extrema. The calculated enthalpy coefficients of pair interactions of the amino acid with cosolvent molecules were positive and increased in the series acetonitrile, 1,4-dioxane, DMSO, acetone. The results obtained were interpreted from the point of view of various types of interactions in solutions and the influence of the nature of organic solvents on the thermochemical characteristics of solutions.

Electron-ion dissociative recombination rate constants relevant to the Titan atmosphere and the Interstellar Medium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Osborne, David; Lawson, Patrick; Adams, Nigel, E-mail: ngadams@uga.edu

Following the arrival of Cassini at Titan in 2004, the Titan atmosphere has been shown to contain large complex polycyclic-aromatic hydrocarbons. Since Cassini has provided a great deal of data, there exists a need for kinetic rate data to help with modeling this atmosphere. One type of kinetic data needed is electron-ion dissociative recombination (e-IDR) rate constants. These data are not readily available for larger compounds, such as naphthalene, or oxygen containing compounds, such as 1,4 dioxane or furan. Here, the rate constants for naphthalene, 1,4 dioxane, and furan have been measured and their temperature dependencies are determined when possible,more » using the University of Georgia's Variable Temperature Flowing Afterglow. The rate constants are compared with those previously published for other compounds; these show trends which illustrate the effects which multi-rings and oxygen heteroatoms substitutions have upon e-IDR rate constants.« less

Dihydroxyacetone variants in the organocatalytic construction of carbohydrates: mimicking tagatose and fuculose aldolases.

PubMed

Suri, Jeff T; Mitsumori, Susumu; Albertshofer, Klaus; Tanaka, Fujie; Barbas, Carlos F

2006-05-12

Dihydroxyacetone variants have been explored as donors in organocatalytic aldol reactions with various aldehyde and ketone acceptors. The protected form of dihydroxyacetone that was chosen for in-depth study was 2,2-dimethyl-1,3-dioxan-5-one, 1. Among the catalysts surveyed here, proline proved to be superior in terms of yield and stereoselectivities in the construction of various carbohydrate scaffolds. In a fashion analogous to aldolase enzymes, the de novo preparation of L-ribulose, L-lyxose, D-ribose, D-tagatose, 1-amino-1-deoxy-D-lyxitol, and other carbohydrates was accomplished via the use of 1 and proline. In reactions using 2,2-dimethyl-1,3-dioxan-5-one 1 as a donor, (S)-proline can be used as a functional mimic of tagatose aldolase, whereas (R)-proline can be regarded as an organocatalytic mimic of fuculose aldolase.

Electron-ion dissociative recombination rate constants relevant to the Titan atmosphere and the Interstellar Medium

NASA Astrophysics Data System (ADS)

Osborne, David; Lawson, Patrick; Adams, Nigel

2014-01-01

Following the arrival of Cassini at Titan in 2004, the Titan atmosphere has been shown to contain large complex polycyclic-aromatic hydrocarbons. Since Cassini has provided a great deal of data, there exists a need for kinetic rate data to help with modeling this atmosphere. One type of kinetic data needed is electron-ion dissociative recombination (e-IDR) rate constants. These data are not readily available for larger compounds, such as naphthalene, or oxygen containing compounds, such as 1,4 dioxane or furan. Here, the rate constants for naphthalene, 1,4 dioxane, and furan have been measured and their temperature dependencies are determined when possible, using the University of Georgia's Variable Temperature Flowing Afterglow. The rate constants are compared with those previously published for other compounds; these show trends which illustrate the effects which multi-rings and oxygen heteroatoms substitutions have upon e-IDR rate constants.

Effect of Temperature on Viscosity of S-Substituted Triazinothiocarbamides in 60% Dioxane Water Mixture

NASA Astrophysics Data System (ADS)

Kshirsagar, A. M.; Tayade, D. T.

2012-10-01

S-triazine and thiocarbamide group containing drug create their own identity in the drug, pharmaceutical and medicinal sciences in last four decades. Hence, the viscometric measurements of recently synthesized drugs viz. 1-(4-hydroxy-6-methyl)-S-triazino-3-phenylthiocarbamide (L1) and 1-(4-hydroxy-6-methyl)-S-triazino-3-methylthiocarbamide (L2), were carried out at 60% various percentage of solvent to investigate effect of structure, on group of S-triazinothiocarbamides. The result obtained during this investigation directly through light on the dipole association of compound, intermolecular attraction between solute and solvent, dielectric constant of medium, polarizability and mutual compensation of dipoles and useful for drug absorption, transmission, stability, activity and effect of drug. %K 1-(4-hydroxy-6-methyl)-S-triazino-3-phenylthiocarbamide (L1) and 1-(4-hydroxy-6-methyl)-S-triazino-3-methylthiocarbamide (L2), dioxane-water mixture, viscometric measurements.

40 CFR Table 9 to Subpart Ggg of... - Default Biorates for Soluble HAP

Code of Federal Regulations, 2010 CFR

2010-07-01

....178 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol dimethyl ether 0.364 Ethylene glycol monobutyl ether acetate 0.496 Ethylene glycol monomethyl ether acetate 0.159 Isophorone 0.598 Methanol a...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2010 CFR

2010-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol dimethyl ether 0.364 Ethylene glycol monomethyl ether acetate 0.159 Ethylene glycol monobutyl ether acetate...

Radioimmunoassay of LH (in Japanese)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Motohashi, T.; Yogo, I.

The methods of isolation of binding free hormones (B/F), the double antibody method, adsorption method (dextran charcoal method), and precipitation method (dioxane method) were compared for the RIA of LH in the blood. Comparison of the standard curves revealed no difference among the three methods within measurable limits. The dextran charcoal method, a rapid quantitative determination, tended to be inferior in the variation and reproducibility of intraassay. The dioxane method was shown to be an excellent method in the convenience of procedures, precision, and reproducibility, except for the disadvantage of using an antigen-antibody system which is heterologous to LH. Whenmore » changes in the LH values during menstrual cycles in normal Mature women were examined, a large increase was observed in the phase of ovulation. In case of the administration of Enavid, an oral contraceptive, large fluctuations occurred in the LH value, indicating that ovulation was accompanied by an increase in LR. Changes in the blood LH before, during, and after the administration of Clomid, aimed at ovulation induction, were observed. (Japan)« less

Evaluation of Feruloylated and p-Coumaroylated Arabinosyl Units in Grass Arabinoxylans by Acidolysis in Dioxane/Methanol.

PubMed

Lapierre, Catherine; Voxeur, Aline; Karlen, Steven D; Helm, Richard F; Ralph, John

2018-05-30

The arabinosyl side chains of grass arabinoxylans are partially acylated by p-coumarate ( pCA) and ferulate (FA). These aromatic side chains can cross-couple wall polymers resulting in modulation of cell wall physical properties. The determination of p-coumaroylated and feruloylated arabinose units has been the target of analytical efforts with trifluoroacetic acid hydrolysis the standard method to release feruloylated and p-coumaroylated arabinose units from arabinoxylans. Herein, we report on a more robust method to measure these acylated units. Acidolysis of extractive-free grass samples in a dioxane/methanol/aqueous 2 M HCl mixture provided the methyl 5- O- p-coumaroyl- and 5- O-feruloyl-l-arabinofuranoside anomers ( pCA-MeAra and FA-MeAra). These conjugates were readily analyzed by liquid chromatography combined with both UV and MS detection. The method revealed the variability of the relative acylation of arabinose units by pCA or FA in grass cell walls. This methodology will permit delineation of hydroxycinnamate acylation patterns in arabinoxylans.

Characterization of Meldrum's acid derivative 5-(5-Ethyl-1,3,4-thiadiazol-2-ylamino)methylene-2,2-dimethyl-1,3-dioxane-4,6-dione by Raman and FT-IR spectroscopy and DFT calculations

NASA Astrophysics Data System (ADS)

de Toledo, T. A.; da Silva, L. E.; Teixeira, A. M. R.; Freire, P. T. C.; Pizani, P. S.

2015-07-01

In this study, the structural and vibrational properties of Meldrum's acid derivative 5-(5-Ethyl-1,3,4-thiadiazol-2-ylamino)methylene-2,2-dimethyl-1,3-dioxane-4,6-dione, C11H13N3O4S were studied combining experimental techniques such as Raman and FT-IR spectroscopy and density functional theory (DFT) calculations. The Raman and FT-IR spectra were recorded at room conditions in the regions from 80 to 3400 cm-1 and 400 to 4000 cm-1, respectively. Vibrational wavenumbers were predicted using DFT calculations with the hybrid functional B3LYP and basis set 6-31G(d,p). A comparison between experimental and theoretical data is provided for the Raman and FT-IR spectra. The descriptions of the normal modes were carried by means of potential energy distribution (PED).

Three new enantiomerically pure ferrocenylphosphole compounds.

PubMed

López Cortés, José Guadalupe; Vincendeau, Sandrine; Daran, Jean Claude; Manoury, Eric; Gouygou, Maryse

2006-05-01

The absolute configurations of three new enantiomerically pure ferrocenylphosphole compounds, namely (2S,4S,S(Fc))-4-methoxymethyl-2-[2-(9-thioxo-9lambda5-phosphafluoren-9-yl)ferrocenyl]-1,3-dioxane, [Fe(C5H5)(C23H22O3PS)], (III), (S(Fc))-[2-(9-thioxo-9lambda5-phosphafluoren-9-yl)ferrocenyl]methanol, [Fe(C5H5)(C18H14OPS)], (V), and (S(Fc))-diphenyl[2-(9-thioxo-9lambda5-phosphafluoren-9-yl]ferrocenylmethyl]phosphine, [Fe(C5H5)(C30H23P2)], (VIII), have been unambiguously established. All three ligands contain a planar chiral ferrocene group, bearing a dibenzophosphole and either a dioxane, a methanol or a diphenylphosphinomethane group on the same cyclopentadienyl. In compound (V), the occurrence of O-H...S and C-H...S hydrogen bonds results in the formation of a two-dimensional network parallel to (001). The geometry of the ferrocene frameworks agrees with related reported structures.

pH-Independent Recognition of Polyhydroxy Compounds by Niobium(V) Porphyrin Complex with Unique Sugar Selectivity.

PubMed

Doi, Takuya; Kachikawa, Norihide; Yasui, Takashi; Yuchi, Akio

2017-01-01

The niobium(V) complex with tetraphenylporphin having OH - as an auxilliay ligand exists as a dimeric complex, [Nb 2 (tpp) 2 O 3 ] at a total concentration >10 -4.5 mol dm -3 , and reacts with an aliphatic or aromatic polyhydroxy compound to form a monomeric complex containing chelate rings by coordination of the deprotonated species, and to cause an appreciable UV-Vis spectral change. In contrast to phenylboronic acid (PBA), the reactivity of [Nb 2 (tpp) 2 O 3 ] is independent of pH at least between 4 and 8. Aliphatic comounds are more reactive than aromatic compounds in dioxane-water, while the reactivity order is reversed in the two-phase reaction. The sugar selectivity order of [Nb 2 (tpp) 2 O 3 ] in dioxane-water (10:1) (sorbose > fructose > mannose > arabinose, galactose > glucose) is appreciably different from that of PBA (fructose > sorbose > arabinose > galactose > mannose > glucose). This may be related to the difference in size of the Lewis acidic center.

Electrochemical systems and methods using metal halide to form products

DOE Office of Scientific and Technical Information (OSTI.GOV)

Albrecht, Thomas A.; Solas, Dennis; Leclerc, Margarete K.

There are provided electrochemical methods and systems to form one or more organic compounds or enantiomers thereof selected from the group consisting of substituted or unsubstituted dioxane, substituted or unsubstituted dioxolane, dichloroethylether, dichloromethyl methyl ether, dichloroethyl methyl ether, chloroform, carbon tetrachloride, phosgene, and combinations thereof.

ENTHALPIES OF FORMATION OF CYCLIC ALKYL PEROXIDES: 1,2-DIOXETANE, 1,2-DIOXOLANE, AND 1,2-DIOXANE. (R824970)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

The Changing Landscape of Chemical Toxicity Values and Challenges Presented with Trichloroethylene

DTIC Science & Technology

2012-12-11

become Risk Management Actions (RMAs) BUILDING STRONG® IRIS Documents Reviewed by DoD Services  Benzo(a)pyrene  Trimethylbenzenes  Dioxin ...4 BUILDING STRONG® Other Chemicals of DoD Interest Undergoing IRIS Reassessment  1,4-Dioxane  Dioxin (cancer)  RDX  Arsenic

40 CFR Table 3 to Subpart Ggg of... - Soluble HAP

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Soluble HAP 3 Table 3 to Subpart GGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... HAP Compound 1,1-Dimethylhydrazine. 1,4-Dioxane. Acetonitrile. Acetophenone. Diethyl sulfate. Dimethyl...

Niosh analytical methods for Set G

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1976-12-01

Industrial Hygiene sampling and analytical monitoring methods validated under the joint NIOSH/OSHA Standards Completion Program for Set G are contained herein. Monitoring methods for the following compounds are included: butadiene, heptane, ketene, methyl cyclohexane, octachloronaphthalene, pentachloronaphthalene, petroleum distillates, propylene dichloride, turpentine, dioxane, hexane, LPG, naphtha(coal tar), octane, pentane, propane, and stoddard solvent.

Variations in the heterogeneity of the decay of the fluorescence in six procyanidin dimers

Treesearch

Donghwan Cho; Rujiang Tian; Lawrence J. Porter; Richard W. Hemingway; Wayne L. Mattice

1990-01-01

The decay of the fluorescence has been measured in 1,4-dioxane for six dimers of (2R,3R)-(-)-epicatechin and (2R,3S)-(+)-catechin, hereafter denoted simply epicatechin and catechin. The dimers are epicatechin-(4β→8)-catechin, epicatechin-(4β→8)-epicatechin...

77 FR 7576 - Draft Toxicological Review of 1,4-Dioxane: In Support of Summary Information on the Integrated...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-13

... Center for Environmental Assessment (NCEA) within the EPA Office of Research and Development. EPA is... Research and Development, Research Triangle Park, NC 27711; telephone: (919) 541- 1964; facsimile: (919... EPA's IRIS is a human health assessment program that evaluates quantitative and qualitative risk...

Onset of hydrogen bonded collective network of water in 1,4-dioxane.

PubMed

Luong, Trung Quan; Verma, Pramod Kumar; Mitra, Rajib Kumar; Havenith, Martina

2011-12-22

We have studied the evolution of water hydrogen bonded collective network dynamics in mixtures of 1,4-dioxane (Dx) as the mole fraction of water (X(w)) increases from 0.005 to 0.54. The inter- and intramolecular vibrations of water have been observed using terahertz time domain spectroscopy (THz-TDS) in the frequency range 0.4-1.4 THz (13-47 cm(-1)) and Fourier transform infrared (FTIR) spectroscopy in the far-infrared (30-650 cm(-1)) and mid-infrared (3000-3700 cm(-1)) regions. These results have been correlated with the reactivity of water in these mixtures as determined by kinetic studies of the solvolysis reaction of benzoyl chloride (BzCl). Our studies show an onset of intermolecular hydrogen bonded water network dynamics beyond X(w) ≥ 0.1. At the same concentration, we observe a rapid increase of the rate constant of solvolysis of BzCl in water-Dx mixtures. Our results establish a correlation between the onset of collective hydrogen bonded network with the solvation dynamics and the activity of clustered water.

Near infrared cavity enhanced absorption spectra of atmospherically relevant ether-1, 4-Dioxane.

PubMed

Chandran, Satheesh; Varma, Ravi

2016-01-15

1, 4-Dioxane (DX) is a commonly found ether in industrially polluted atmosphere. The near infrared absorption spectra of this compound has been recorded in the region 5900-8230 cm(-1) with a resolution of 0.08 cm(-1) using a novel Fourier transform incoherent broadband cavity-enhanced absorption spectrometer (FT-IBBCEAS). All recorded spectra were found to contain regions that are only weakly perturbed. The possible combinations of fundamental modes and their overtone bands corresponding to selected regions in the measured spectra are tabulated. Two interesting spectral regions were identified as 5900-6400 cm(-1) and 8100-8230 cm(-1). No significant spectral interference due to presence of water vapor was observed suggesting the suitability of these spectral signatures for spectroscopic in situ detection of DX. The technique employed here is much more sensitive than standard Fourier transform spectrometer measurements on account of long effective path length achieved. Hence significant enhancement of weaker absorption lines above the noise level was observed as demonstrated by comparison with an available measurement from database. Copyright © 2015 Elsevier B.V. All rights reserved.

Characteristics of Lignin Fractions from Dilute Acid Pretreated Switchgrass and Their Effect on Cellobiohydrolase from Trichoderma longibrachiatum

DOE PAGES

Yao, Lan; Yang, Haitao; Yoo, Chang Geun; ...

2018-02-06

To investigate the interactions between acid pretreated switchgrass lignin and cellobiohydrolase (CBH), three different lignin fractions were isolated from dilute acid pretreated switchgrass by (i) ethanol extraction, followed by (ii) dioxane/H2O extraction, and (iii) cellulase treatment, respectively. Structural properties of each lignin fraction were elucidated by GPC, 13C-NMR, and 2D-HSQC NMR analyses. The adsorptions of CBH to the isolated lignin fractions were also studied by Langmuir adsorption isotherms. Ethanol-extractable lignin fraction, mainly composed of syringyl (S) and guaiacyl (G) units, had the lowest molecular weight, while dioxane/H2O-extracted lignin fraction had the lowest S/G ratio with higher content of p-coumaric acidmore » (pCA) unit. The residual lignin fraction after enzymatic treatment had the highest S/G ratio without hydroxyphenyl (H) unit. Strong associations were found between lignin properties such as lignin composition and S/G ratio and its non-productive enzyme adsorption factors including the maximum adsorption capacity and binding strength.« less

Comparison of the acetyl bromide spectrophotometric method with other analytical lignin methods for determining lignin concentration in forage samples.

PubMed

Fukushima, Romualdo S; Hatfield, Ronald D

2004-06-16

Present analytical methods to quantify lignin in herbaceous plants are not totally satisfactory. A spectrophotometric method, acetyl bromide soluble lignin (ABSL), has been employed to determine lignin concentration in a range of plant materials. In this work, lignin extracted with acidic dioxane was used to develop standard curves and to calculate the derived linear regression equation (slope equals absorptivity value or extinction coefficient) for determining the lignin concentration of respective cell wall samples. This procedure yielded lignin values that were different from those obtained with Klason lignin, acid detergent acid insoluble lignin, or permanganate lignin procedures. Correlations with in vitro dry matter or cell wall digestibility of samples were highest with data from the spectrophotometric technique. The ABSL method employing as standard lignin extracted with acidic dioxane has the potential to be employed as an analytical method to determine lignin concentration in a range of forage materials. It may be useful in developing a quick and easy method to predict in vitro digestibility on the basis of the total lignin content of a sample.

Characteristics of Lignin Fractions from Dilute Acid Pretreated Switchgrass and Their Effect on Cellobiohydrolase from Trichoderma longibrachiatum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yao, Lan; Yang, Haitao; Yoo, Chang Geun

To investigate the interactions between acid pretreated switchgrass lignin and cellobiohydrolase (CBH), three different lignin fractions were isolated from dilute acid pretreated switchgrass by (i) ethanol extraction, followed by (ii) dioxane/H2O extraction, and (iii) cellulase treatment, respectively. Structural properties of each lignin fraction were elucidated by GPC, 13C-NMR, and 2D-HSQC NMR analyses. The adsorptions of CBH to the isolated lignin fractions were also studied by Langmuir adsorption isotherms. Ethanol-extractable lignin fraction, mainly composed of syringyl (S) and guaiacyl (G) units, had the lowest molecular weight, while dioxane/H2O-extracted lignin fraction had the lowest S/G ratio with higher content of p-coumaric acidmore » (pCA) unit. The residual lignin fraction after enzymatic treatment had the highest S/G ratio without hydroxyphenyl (H) unit. Strong associations were found between lignin properties such as lignin composition and S/G ratio and its non-productive enzyme adsorption factors including the maximum adsorption capacity and binding strength.« less

Endoperoxide polyketides from a Chinese Plakortis simplex: further evidence of the impact of stereochemistry on antimalarial activity of simple 1,2-dioxanes.

PubMed

Chianese, Giuseppina; Persico, Marco; Yang, Fan; Lin, Hou-Wen; Guo, Yue-Wei; Basilico, Nicoletta; Parapini, Silvia; Taramelli, Donatella; Taglialatela-Scafati, Orazio; Fattorusso, Caterina

2014-09-01

Chemical investigation of the organic extract obtained from the sponge Plakortis simplex collected in the South China Sea afforded five new polyketide endoperoxides (2 and 4-7), along with two known analogues (1 and 3). The stereostructures of these metabolites have been deduced on the basis of spectroscopic analysis and chemical conversion. The isolated endoperoxide derivatives have been tested for their in vitro antimalarial activity against Plasmodium falciparum strains, showing IC50 values in the low micromolar range. The structure-activity relationships were analyzed by means of a detailed computational investigation and rationalized in the light of the mechanism of action proposed for this class of simple antimalarials. The relative orientation of the atoms involved in the putative radical generation and transfer reaction was demonstrated to have a great impact on the antimalarial activity. The resulting 3D pharmacophoric model can be a useful guide to design simple and effective antimalarial lead compounds belonging to the class of 1,2-dioxanes. Copyright © 2014 Elsevier Ltd. All rights reserved.

Rapid, High Affinity Binding by a Fluorescein Templated Copolymer Combining Covalent, Hydrophobic, and Acid–Base Noncovalent Crosslinks

PubMed Central

Timberman, Anthony; Yang, Rongfang; Papantones, Alex; Seitz, W. Rudolf

2018-01-01

A new type of biomimetic templated copolymer has been prepared by reverse addition fragmentation chain transfer polymerization (RAFT) in dioxane. The initial formulation includes the template fluorescein, N-isopropylacrylamide (NIPAM, 84 mol %), methacrylic acid (MAA, 5-mol %), 4-vinylpyridine (4-VP, 9 mmol %), and N,N′-methylenebis(acrylamide) (MBA, 2 mol %). PolyNIPAM is a thermosensitive polymer that comes out of aqueous solution above its lower critical solution temperature forming hydrophobic ‘crosslinks’. MAA and 4-VP interact in dioxane forming acid–base crosslinks. The excess 4-VP serves as a recognition monomer organizing around the template fluorescein to form a binding site that is held in place by the noncovalent and covalent crosslinks. The MBA is a covalent crosslinker. The RAFT agent in the resulting copolylmer was reduced to a thiol and attached to gold nanoparticles. The gold nanoparticle bound copolymer binds fluorescein completely in less than two seconds with an affinity constant greater than 108 M−1. A reference copolymer prepared with the same monomers by the same procedure binds fluorescein much more weakly. PMID:29693601

Optimized and Validated Spectrophotometric Methods for the Determination of Enalapril Maleate in Commercial Dosage Forms

PubMed Central

Rahman, Nafisur; Haque, Sk Manirul

2008-01-01

Four simple, rapid and sensitive spectrophotometric methods have been proposed for the determination of enalapril maleate in pharmaceutical formulations. The first method is based on the reaction of carboxylic acid group of enalapril maleate with a mixture of potassium iodate (KIO3) and iodide (KI) to form yellow colored product in aqueous medium at 25 ± 1°C. The reaction is followed spectrophotometrically by measuring the absorbance at 352 nm. The second, third and fourth methods are based on the charge transfer complexation reaction of the drug with p-chloranilic acid (pCA) in 1, 4-dioxan-methanol medium, 2, 3-dichloro 5, 6-dicyano 1, 4-benzoquinone (DDQ) in acetonitrile-1,4 dioxane medium and iodine in acetonitrile-dichloromethane medium. Under optimized experimental conditions, Beer’s law is obeyed in the concentration ranges of 2.5–50, 20–560, 5–75 and 10–200 μg mL−1, respectively. All the methods have been applied to the determination of enalapril maleate in pharmaceutical dosage forms. Results of analysis are validated statistically. PMID:19609388

Use of food and packaging model matrices to investigate the antioxidant properties of biorefinery grass lignins.

PubMed

Aguié-Béghin, Véronique; Foulon, Laurence; Soto, Paola; Crônier, David; Corti, Elena; Legée, Frédéric; Cézard, Laurent; Chabbert, Brigitte; Maillard, Marie-Noëlle; Huijgen, Wouter J J; Baumberger, Stéphanie

2015-11-18

The antioxidant properties of grass lignins recovered from an alkaline industrial process and from different ethanol organosolv pretreatment processes were compared using two types of tests: (i) classical radical 2,2'-diphenyl-1-picrylhydrazyl (DPPH(•)) scavenging tests in dioxane/water or ethanol and (ii) tests involving multiphasic systems (lipid dispersion in water or cellulose film suspended in ethanol). These multiphasic systems were representative of food and packaging matrices in view of high-value applications. All lignins, in solution or in the film, effectively scavenged radicals. Moreover, they were competitive with a food commercial rosemary extract to protect linoleic acid against oxidation. Whereas the DPPH(•) test in dioxane was not discriminant, differences appeared between lignins when the test was performed in ethanol or with the multiphasic systems. Moreover, radical scavenging activity was preserved in the film even after its immersion in ethanol. Structural analysis of lignins revealed that low-molar-mass phenolics, namely p-hydroxycinnamic acids and lignin depolymerization products, governed lignin antioxidant properties in the multiphasic systems.

Multiphase materials with lignin. IV. Blends of hydroxypropyl cellulose with lignin

Treesearch

Timothy G. Rials; Wolfgang G. Glasser

1989-01-01

Polymer blends of hydroxypropyl cellulose (HPC) and organosolv lignin (OSL) were prepared by mixing in solutions of both pyridine and dioxane, and casting as films, and by mixing in the melt followed by extrusion. All preparations exhibited partial miscibility as evidenced by a single Tg up to a composition of 40 wt % lignin above which phase...

An Organic Puzzle Using Meldrum's Acid

NASA Astrophysics Data System (ADS)

Crouch, R. David; Holden, Michael S.

2002-04-01

Meldrum's acid or 2,2-dimethyl-1,3-dioxane-4,6-dione undergoes a Knoevenagel condensation with formaldehyde to form an active Michael acceptor for a second molecule of Meldrum's acid. The structure of the resulting product is determined by correlation of the products of possible reactions of Meldrum's acid and formaldehyde with the NMR spectrum of the product.

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2014 CFR

2014-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2013 CFR

2013-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2012 CFR

2012-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

40 CFR Table 37 to Subpart G of... - Default Biorates for List 1 Compounds

Code of Federal Regulations, 2011 CFR

2011-07-01

... DIMethyl sulfate 0.178 Dinitrophenol 2,4 0.620 Dinitrotoluene(2,4) 0.784 Dioxane(1,4) 0.393 Ethylene glycol... 0.496 Hexachlorobenzene 16.179 ISophorone 0.598 Methanol 0.200 Methyl methacrylate 4.300 Nitrobenzene 2.300 Toluidine (-0) 0.859 Trichlorobenzene 1,2,4 4.393 Trichlorophenol 2,4,5 4.477 Triethylamine...

Novel Side-Chain Liquid Cyrstalline Polymers

DTIC Science & Technology

1989-01-01

Synthesis and Characterization of Liquid Crystalline Polyacrylates and Poly- methacrylates Containing Benzyl Ether and Diphenyl Ethane Based Mesogens J...Crystalline Polymethacrylates and Polyacrylates of trans 2-[4-(11- hydroxyundecanyloxy)-3,5-dimethylphenylI-4-(4-methoxyphenyl)-l,3-dioxane Makromol. Chem., 189...and Characterization of Liquid Crystalline Polyacrylates and Poly- met acrylates Containing Benzyl Ether and Diphenyl Ethane Based Mesogens J. Polym

75 FR 63827 - Integrated Risk Information System (IRIS); Request for Chemical Substance Nominations for 2011...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-18

........... 156-60-5 1,4-dioxane (oral) 123-91-1 ethylene glycol monobutyl ether 111-76-2 (EGBE...-dichlorobenzene 106-46-7 1,2-dichloroethane (ethylene 107-06-2 dichloride). dichloromethane (methylene 75-09-2... 131-18-0 ethanol 64-17-5 ethyl tertiary butyl ether (ETBE). 637-92-3 ethylbenzene 100-41-4 ethylene...

Effect of solvent quality on aggregate structures of common surfactants.

PubMed

Hollamby, Martin J; Tabor, Rico; Mutch, Kevin J; Trickett, Kieran; Eastoe, Julian; Heenan, Richard K; Grillo, Isabelle

2008-11-04

Aggregate structures of two model surfactants, AOT and C12E5 are studied in pure solvents D2O, dioxane-d8 (d-diox) and cyclohexane-d12 (C6D12) as well as in formulated D2O/d-diox and d-diox/C6D12 mixtures. As such these solvents and mixtures span a wide and continuous range of polarities. Small-angle neutron scattering (SANS) has been employed to follow an evolution of the preferred aggregate curvature, from normal micelles in high polarity solvents, through to reversed micelles in low polarity media. SANS has also been used to elucidate the micellar size, shape as well as to highlight intermicellar interactions. The results shed new light on the nature of aggregation structures in intermediate polarity solvents, and point to a region of solvent quality (as characterized by Hildebrand Solubility Parameter, Snyder polarity parameter or dielectric constant) in which aggregation is not favored. Finally these observed trends in aggregation as a function of solvent quality are successfully used to predict the self-assembly behavior of C12E5 in a different solvent, hexane-d14 (C6D14).

Germylenes and stannylenes stabilized within N2PE rings (E = Ge or Sn): combined experimental and theoretical study.

PubMed

Vrána, Jan; Ketkov, Sergey; Jambor, Roman; Růžička, Aleš; Lyčka, Antonín; Dostál, Libor

2016-06-21

The deprotonation of aminophosphanes PhP(NHR)2 (R = t-Bu or Dip; Dip = 2,6-i-Pr2C6H3) and t-BuP(NHDip)2 using n-BuLi gave, depending on the stoichiometry, both the dilithium compounds {[PhP(Nt-Bu)2]Li2}2 (), [PhP(Nt-Bu)(NDip)]Li2·(Et2O) (), [t-BuP(NDip)2]Li2·(Et2O)2 () and [t-BuP(NDip)2]Li2·(tmeda)2 (), and the monolithium compounds [PhP(NHt-Bu)(NR)]Li·(tmeda) (R = t-Bu , Dip ) and [t-BuP(NHDip)(NDip)]Li·(tmeda) (). Treatment of , and with GeCl2·dioxane or SnCl2 in a 1 : 1 stoichiometric ratio gave the corresponding tetrylenes [PhP(Nt-Bu)2]E (E = Ge , Sn ), [PhP(Nt-Bu)(NDip)]Ge () and [t-BuP(NDip)2]E (E = Ge , Sn ). The heteroleptic germylene [Ph(H)P(Nt-Bu)2]GeCl () was obtained by the reaction of the monolithium compound [PhP(NHt-Bu)(Nt-Bu)]Li·(tmeda) () with GeCl2·dioxane in a 1 : 1 stoichiometric ratio, as a result of a spontaneous NH → PH tautomeric shift in the ligand backbone. In contrast, an analogous reaction with SnCl2 produced only stannylene along with the PhP(NHt-Bu)2 starting material, suggesting scrambling of the ligands rather than a NH → PH tautomeric shift. Finally, heating in solution led to P-C bond cleavage and formation of the bis(imino)phosphide [DipNPNDip]Li·(tmeda) (). The reaction of with GeCl2·dioxane, SnCl2 or PbCl2 in a 2 : 1 stoichiometric ratio yielded the unprecedented tetrylenes [DipNPNDip]2E (E = Ge , Sn and Pb ), in which the tetrylene center is incorporated within two N2PE rings. Treatment of the monolithium compound with n-BuLi and K (or KC8) gave [t-BuNPNt-Bu]Li·(tmeda) () and{[t-BuNPNt-Bu]K(tmeda)}2 (), respectively. In contrast to the reaction with , similar reactions of with GeCl2·dioxane and SnCl2 resulted in the known compounds cis-[P(μ-Nt-Bu)2P(t-BuN)2]E (E = Ge, Sn); evidently the t-Bu groups do not provide sufficient steric shielding to protect the bis(imino)phosphide backbone as in the case of . The bonding situation in a set of selected compounds (, ) has been subjected to a theoretical survey with particular emphasis on the nature of the bonding between the ligand and the central metal and the bonding within the NPN core of the ligand, showing significant differences among the studied complexes.

Multiphase materials with lignin. VI. Effect of cellulose derivative structure on blend morphology with lignin

Treesearch

Timothy G. Rials; Wolfgang G. Glasser

1989-01-01

Polymeric blends of lignin with ethyl cellulose (EC) and cellulose acetate/butyrate (CAB) prepared by solution casting from dioxane. Fracture surface analysis by scanning electron microscopy revealed phase separation when the lignin content exceeded 10% for blends with EC and 5% in the CAB system. While this phase behavior is as predicted for the EC blends, a greater...

International Symposium on Solubility Phenomena (3rd) Held in Guildford, Surrey England on 23 - 26 August 1988

DTIC Science & Technology

1988-08-26

metallic iron in these cases, though the ferrate Na FeO is4 3 not existent at such low oxygen potentials. 𔃾 U Wednesday morning 24 August 1988 SESSION 3...acknowledged. 44 ’I 44 P9 Measurement and Calculation of Transfer Enthalpies of Potassium Chloride from Water to Water - Dioxane Mixture W Jian Ji, L

Advanced oxidation of five contaminants in water by UV/TiO2: Reaction kinetics and byproducts identification.

PubMed

Alvarez-Corena, Jose R; Bergendahl, John A; Hart, Fred L

2016-10-01

The extent and kinetics of degradation of 1,4 dioxane, n-nitrosodimethylamine (NDMA), tris-2-chloroethyl phosphate (TCEP), gemfibrozil, and 17β estradiol in a prepared aqueous matrix by means of UV/TiO2 (ultraviolet light/titanium dioxide) oxidation was evaluated. Degussa P25 TiO2 was employed as a photocatalyst excited by UV light in a 1 L water-jacketed batch photoreactor. The rate of degradation was modeled using a pseudo-first order rate model and the Langmuir-Hinshelwood rate model with a high correlation. Degradation rate constants were found to be maximum at pH 5.0 and 1.5 g L(-)(1) TiO2 dose. For these conditions first order rate constants, values were as follows: 0.29 min(-1) for 1,4 dioxane, 0.50 min(-1) for NDMA, 0.12 min(-1) for TCEP, 0.61 min(-1) for gemfibrozil, and 0.53 min(-1) for 17β estradiol. While for the Langmuir-Hinshelwood rate model, the following constants were found: 0.11 Lmg(-1) and 2.81 mgL(-1) min(-1) for 1,4 dioxane, 0.12 Lmg(-1) and 4.35 mgL(-1) min(-1) for NDMA, 0.06 Lmg(-1) and 1.79 mgL(-1) min(-1) for TCEP, 0.21 Lmg(-1) and 3.27 mgL(-1) min(-1) for gemfibrozil, and 0.15 Lmg(-1) and 3.43 mgL(-1) min(-1) for 17β estradiol. In addition, specific byproducts of degradation were identified using GC/MS analysis. The results obtained from the kinetics analysis showed that UV/TiO2 oxidation is a promising process for treating trace organic contaminants in water, but further research is needed to better understand how to incorporate these findings into pilot and full-scale designs. The toxicity of oxidation byproducts, and their potential for interacting with other compounds should be considered in the treatment of contaminated waters using the UV/TiO2 oxidation process. Copyright © 2016 Elsevier Ltd. All rights reserved.

In Situ Treatment and Management Strategies for 1,4-Dioxane-Contaminated Groundwater

DTIC Science & Technology

2017-05-05

microorganisms thrived during the biodegradation process. This was consistent with oxidation process that biodiversity was inhibited by the chemical reaction ...exhibit a strong inhibitory impact on CB1190-like bacteria (Figure 79). However, in well 8MNW54, inhibitory impacts of chemical reactions were clear...inhibited again, indicating that chemical reactions along with high CVOCs levels had widely-varying impacts on microorganisms. Specifically, under low DX

Cubane Derivatives for Propellant Applicationsxb

DTIC Science & Technology

1989-07-03

cycloperitanone ketal containing 2-3% cyclopentanone and trace amounts of toluene. Approximately 4 liters of purified cyclopentanone ketal per day could be...such as reaction with trimethyl phosphite , also gave inconsistent results. In reactions involving 45 moles of ketal in a 20 gallon Pfaudler reactor...Dioxane treated with trimethyl phosphite Dehydrohalogenation and Dimerization of the Tribromo Ketal to the Bisketal. In-0 0 stop 3 0 Gr r or [to"t

Liquid Crystalline Polymers Containing Heterocycloalkane Mesogens. 2. Side-Chain Liquid Crystalline Polysiloxanes Containing 2,5-Disubstituted-1,3-Dioxane Mesogens.

DTIC Science & Technology

1986-10-01

units and an aliphatic spacer containing eleven and respectively, ten methylene units were synthesized. Their phase behavior was studied by differential...scanning calorimetry and optical polarization microscopy, and compared with the phase behavior of the polysiloxanes and copolysiloxanes containing 4...containing eleven and respectively, ten methylene -units were synthesized. Their phase behavior was studied by differential * scanning calorimetry

Microwave-Assisted Rapid Access to Bio-active Heterocycles: Synthesis of 1,3,4-Oxadiazoles, 1,3,4-Thiadiazoles, 1,3-Dioxanes, Pyrazoles, Hydrazones and 3,4-Dihydropyrimidin-2(1H)-ones under Benign Conditions

EPA Science Inventory

Green chemistry is a rapidly developing new field that provides us a proactive avenue for the sustainable development of future science and technologies.1 It emphasis the use of highly efficient and environmental benign synthetic protocols to deliver bio-active heterocycles, acc...

Biodegradation of 1,4-Dioxane

DTIC Science & Technology

2007-08-01

simultaneously transferred to a single flask and provided with toluene as a growth substrate. The cells were subsequently harvested and checked for 1,4... harvested via centrifugation, rinsed with fresh media, and re-suspended to an OD550 of 1-2. Aliquots of the prepared cells were then transferred to...Total RNA from the bacterial cells was isolated with an RNeasy Mini kit (Qiagen, Valencia, CA) with some modifications. The harvested cells were

Geohydrology, water quality, and simulation of ground-water flow in the vicinity of a former waste-oil refinery near Westville, Indiana, 1997-2000

USGS Publications Warehouse

Duwelius, Richard F.; Yeskis, Douglas J.; Wilson, John T.; Robinson, Bret A.

2002-01-01

A three-dimensional, four layer groundwater- flow model was constructed and calibrated to match ground-water levels and streamflow measured during December 1997. The model was used to simulate possible mechanisms of contaminant release, the effect of increased pumpage from water-supply wells, and pumping at the leading edge of the plume as a possible means of remediation. Based on simulation of threewaste-oil lagoons, a vertical hydraulic conductivity of 0.2 feet per day was required to move contaminants into the bottom layer of the model at a constant leakage rate of about 98 gallons per minute. Simulations of a disposal well in layer 3 of the model indicated an injection rate of 50 gallons per minute was necessary to spread contaminants vertically in the aquifer. Simulated pumping rates of about 300 and 1,000 gallons per minute were required for watersupply wells at the Town of Westville and the Westville Correctional Facility to draw water from the plume of 1,4-dioxane. Simulated pumping from hypothetical wells at the leading edge of the plume indicated that three wells, each pumping 25 gallons per minute from model layer 3, would capture the plume of 1,4-dioxane.

Biofouling of contaminated ground-water recovery wells: Characterization of microorganisms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, S.W.; Lange, C.R.; Lesold, E.A.

1997-11-01

The taxonomy and physiology of microorganisms isolated from contaminated ground-water recovery wells prone to biofouling are characterized for an industrial site in Rochester, New York. Principal aquifer contaminants include acetone, cyclohexane, dichloroethane, dichloromethane, 1,4-dioxane, isopropanol, methanol, and toluene. These contaminants represent a significant fraction (up to 95%) of the total organic carbon in the ground water. Ground-water samples from 12 recovery wells were used to isolate, quantify, and identify aerobic and anaerobic bacterial populations. Samples from selected wells were also characterized geochemically to assess redox conditions and availability of essential and trace nutrients. Dominant bacteria, listed in order of descendingmore » numbers, including sulfate-reducers (Desulfovibrio desulfuricans), anaerobic heterotrophs (Actinomyces, Bacteriodes, Bacillus, Agrobacterium), aerobic heterotrophs (Pseudomonas, Flavobacterium, Nocardia, Citrobacter), iron-oxidizers (Gallionella ferruginea, Crenothrix polyspora), iron-reducers (Shewanella), and sulfur-oxidizers (Thiobacillus ferrooxidans). Fungi were also recovered in low numbers. Both aerobic and anaerobic heterotrophs were able to utilize all principal contaminants as sole carbon and energy sources except 1,4-dioxane. The prevalence of heterotrophic bacteria and their ability to use the available anthropogenic carbon suggests that aerobic and anaerobic heterotrophs contribute to the biofouling of wells at this site, in addition to the often cited fouling due to iron-oxidizing bacteria and sulfate-reducing bacteria.« less

Synthesis, structure characterization and biological studies on a new aromatic hydrazone, 5-(2-(1,5-dimethyl-3-oxo-2-phenyl-2,3-dihydro-1H-pyrazol-4-yl)hydrazono)-2,2-dimethyl-1,3-dioxane-4,6-dione, and its transition metal complexes

NASA Astrophysics Data System (ADS)

Kumar, Shubha S.; Biju, S.; Sadasivan, V.

2018-03-01

A new aromatic hydrazone 5-(2-(1,5-dimethyl-3-oxo-2-phenyl-2,3-dihydro-1H-pyrazol-4-yl)hydrazono)-2,2-dimethyl-1,3-dioxane-4,6-dione has been synthesized by Japp-Klingemann reaction from diazotized 4-aminoantipyrine and Meldrum's acid. A few 3d-metal ion complexes of this hydrazone were synthesized. The compound and its complexes were characterized by UV-Visible, 1H NMR, ESR, Mass spectral, molar conductance and magnetic susceptibility measurements. The compound was found to exist in hydrazone form in solid state and solution from SXRD and 1H NMR study. The influence of pH on the molecule was studied and found that it shows azo/enol-hydrazone tautomerism in solution. This molecule act as a univalent tridentate ligand and the complexes were assigned to have a 1:2 stoichiometry (M:L). The antioxidant properties of the compounds were explored by DPPH assay and found that the ligand possesses better free radical scavenging effect than the complexes. Antimicrobial activities of these compounds were investigated and were found to be active.

Isolation and structural characterization of the milled wood lignin, dioxane lignin, and cellulolytic lignin preparations from brewer's spent grain.

PubMed

Rencoret, Jorge; Prinsen, Pepijn; Gutiérrez, Ana; Martínez, Ángel T; Del Río, José C

2015-01-21

The structure of the lignin from brewer's spent grain (BSG) has been studied in detail. Three different lignin preparations, the so-called "milled-wood" lignin (MWL), dioxane lignin (DL), and cellulolytic lignin (CEL), were isolated from BSG and then thoroughly characterized by pyrolysis GC/MS, 2D-NMR, and derivatization followed by reductive cleavage (DFRC). The data indicated that BSG lignin presents a predominance of guaiacyl units (syringyl/guaiacyl ratio of 0.4-0.5) with significant amounts of associated p-coumarates and ferulates. The flavone tricin was also present in the lignin from BSG, as also occurred in other grasses. 2D-NMR (HSQC) revealed that the main substructures present are β-O-4' alkyl-aryl ethers (77-79%) followed by β-5' phenylcoumarans (11-13%) and lower amounts of β-β' resinols (5-6%) and 5-5' dibenzodioxocins (3-5%). The results from 2D-NMR (HMBC) and DFRC indicated that p-coumarates are acylating the γ-carbon of lignin side chains and are mostly involved in condensed structures. DFRC analyses also indicated a minor degree of γ-acylation with acetate groups, which takes place preferentially on S lignin (6% of S units are acetylated) over G lignin (only 1% of G units are acetylated).

About the singular behavior of the ionic condensation of sodium chondroitin sulfate: Conductivity study in water and water dioxane mixture

NASA Astrophysics Data System (ADS)

M'halla, Jalel; Besbes, Rafik; Bouazzi, Ramzi; Boughammoura, Sondes

2006-01-01

In this work, we generalized the (Bjerrum-Debye-Fuoss-MSA) double layer model to an ellipsoidal polyion (chondroitin sulfate) of (∣ Zs∣ e) structural charge, Ls structural length, R minor axe and ( R2 + L2/4) 1/2 major axe. With L ⩽ Ls. Na + counter ions are distributed on the contact (or condensed) layer and on the Debye layer (ionic atmosphere). Both layers are ellipsoidal equipotentials of, respectively, R and d minor axes and are concentric to the polyion. With d = ( R + 1/2 Γ), Γ is the Debye-MSA screen parameter. The equilibrium distribution of Na + ions is derived from a "two states" statistical approach, leading to a general implicit expression for the rate of condensation (1 - α). The generality of this formula results from the fact that it takes into account the finite size of the polyion ( L ≠ ∞ and R ≠ 0) and allows to calculate α for different conformations of the polyion: (ellipsoidal L ≠ 0, cylindrical: L = Ls, spherical: L → 0, and Manning's model: RL-1 → 0). The main conclusion of this model is that, α obeys to the Ostwald's principle of dilution ( α → 1 when CNa+ → 0). This result is contrary to Manning's theory, for which α is a constant αM independent on the concentration Ci: αM = bS/(∣ Zi∣ Lb), with bS = Ls/∣ Zs∣ and Lb = e2/( ɛkT) is the Bjerrum length. However, our analysis shows that the rate of variation: (∂ α/∂ Ci) in a given range of concentration, depends on the structural parameter bS. Indeed, the critical Manning condition ( α-1αM = 1, ⇒(∂ α/∂ Ci) ≈ 0), is compatible with the general following "rod-like model" approximation: (1-α)≈|Zi|(πbS)[4πZi2Lb][αCiR2];withbS″=αM-1 only for some peculiar values of bS and Lb (i.e., dielectric constant: ɛ). In water at 25 °C ( ɛ = 78.3), this singular behavior occurs for a range of a relative low or moderate concentration for some polyelectrolytes of bS structural parameter of about 5.8 Å. This is the case of sodium chondroitin sulfate in water ( bS = 5.72 Å). The addition of dioxane increases Lb, consequently, α is shifted from its Manning's value. In order to verify this dioxane effect, we have compared experimental equivalent conductibilities Λexp of sodium chondroitin sulfate in water ( no shift) and water-dioxane (60 wt%) mixture ( positive shift), to their theoretical values ΛM, ΛcthandΛsth corresponding, respectively, to the Manning, cylindrical and spherical models. This comparison allows also, to explain the conformation "chosen" by the polyion, in order to minimizing the friction effects (due to: viscosity; ionic and dielectric relaxations) and therefore, to optimize its mobility by the shift of its rate of ionic condensation α.

Novel, Solvent-Free, Single Ion Conductive Polymer Electrolytes

DTIC Science & Technology

2008-01-20

liquid oligomeric analogue PEODME (ε = 8, dioxane:CH3CN mass ratio 48:7). The choice of the solvent mixture was a compromise between the...trifluoride – a derivative of Lewis acid properties. An increase in the degree of dissociation, decrease in the share of ionic associates and increase in...diphenylphosphinate this product is a solid, and in reaction with lithium diphenylphosphate the second fraction is a viscous, light-brown liquid , and

ER-1422: Biodegradation of 1,4-Dioxane

DTIC Science & Technology

2007-08-01

simultaneously transferred to a single flask and provided with toluene as a growth substrate. The cells were subsequently harvested and checked for 1,4... harvested via centrifugation, rinsed with fresh media, and re-suspended to an OD550 of 1-2. Aliquots of the prepared cells were then transferred to...Total RNA from the bacterial cells was isolated with an RNeasy Mini kit (Qiagen, Valencia, CA) with some modifications. The harvested cells were

Studies of Halogen Bonding Using High-Pressure Diffractometry

DTIC Science & Technology

2007-11-08

mixed at room temperature. The 1:1 cocrystal was melted by heating it to and in the liquid form loaded to a DAC. Single-crystal of each compound or...upper edge. Figure 6. Isochoric growth of the 1,2-diiodoperfluoroethane:1,4-dioxane 1:1 cocrystal : (a) the melting process of the polycrystal...impurities in the mixture, which condensed at high pressure and grouped between the cocrystal upper face (001) and the upper culet. Figure 7. Isochoric

Transition-Metal-Free Alkynylation of Aryl Chlorides

PubMed Central

Truong, Thanh; Daugulis, Olafs

2011-01-01

Two sets of conditions have been developed for a base-mediated, transition-metal-free alkynylation of aryl chlorides that proceeds via benzyne intermediates. The first set of conditions involves the use of TMPLi base in a pentane/THF mixture at 25 °C. The second set involves use of a metal alkoxide base in dioxane at elevated temperature. Reasonable functional group tolerance has been observed. Fluoro, trifluoromethyl, silyl, cyano, and alcohol functionalities are compatible with the reaction conditions. PMID:21786825

Use of the fluorescence quantum yield for the determination of the number-average molecular weight of polymers of epicatechin with 4β→8 interflavin bonds

Treesearch

D. Cho; W.L. Mattice; L.J. Porter; Richard W. Hemingway

1989-01-01

Excitation at 280 nm produces a structureless emission band with a maximum at 321-324 nm for dilute solutions of catechin, epicatechin, and their oligomers in l,4-dioxane or water. The fluorescence quantum yield, Q, has been measured in these two solvents for five dimers, a trimer, a tetramer, a pentamer, a hexamer, and a polymer in which the monomer...

Complexation of Contaminants and Aqueous-Phase Ozone with Cyclodextrin for Emerging Contaminant Oxidative Degradation

NASA Astrophysics Data System (ADS)

Khan, N. A.; Carroll, K. C.

2016-12-01

Recalcitrant emerging contaminants in groundwater, such as 1,4-dioxane, require strong oxidants for complete mineralization, whereas strong oxidant efficacy for in-situ chemical oxidation (ISCO) is limited by oxidant decay, reactivity, and non-specificity. Hydroxypropyl-β-cyclodextrin (HPβCD) was examined for its ability to stabilize aqueous phase ozone (O3) and prolong oxidation potential through inclusion complex formation. Partial transformation of HPβCD by O3 was observed but HPβCD proved to be sufficiently resilient and only partially degraded in the presence of O3. The formation of a HPβCD:O3 inclusion clathrate complex was observed, and multiple methods for binding constant measurements carried out and compared for HPβCD complexes with O3 and multiple contaminants. The presence of HPβCD increased the O3 half-life linearly with increasing HPβCD:O3 molar ratio. The O3 half-life in solutions increased by as much as 40-fold relative to HPβCD-free O3 solutions, and complexation reversibility was confirmed. Decay rate coefficients increased for 1,4-dioxane, trichloroethene, and trichloroethane likely due to the formation of HPβCD-O3-contaminant ternary complexes. These results suggest that the use of clathrate stabilizers, such as HPβCD, can support the development of a facilitated-transport enabled ISCO for the O3 treatment of groundwater impacted by recalcitrant emerging contaminants.

Conformational analyses of 2,3-dihydroxypropanoic acid as a function of solvent and ionization state as determined by NMR spectroscopy.

PubMed

Drake, Michael D; Harsha, Alex K; Terterov, Sergei; Roberts, John D

2006-03-01

Vicinal (1)H--(1)H coupling constants were used to determine the conformational preferences of 2,3-dihydroxypropanoic acid (1) (DL-glyceric acid) in various solvents and its different carboxyl ionization states. The stereospecific assignments of J(12) and J(13) were confirmed through the point-group substitution of the C-3 hydrogen with deuterium, yielding rac-(2SR,3RS)-[3-(2)H]-1, and the observation of only J(13) in the (1)H NMR spectra. While hydrogen bonding and steric strain may be expected to drive the conformational equilibrium, their role is overshadowed by a profound gauche effect between the vicinal hydroxyl groups that mimics other substituted ethanes, such as 1,2-ethanediol and 1,2-difluoroethane. At low pH, the conformational equilibrium is heavily weighted toward the gauche-hydroxyl rotamers with a range of 81% in DMSO-d(6) to 92% in tert-butyl alcohol-d(10). At high pH, the equilibrium exhibits a larger dependence upon the polarity and solvating capability of the medium, although the gauche effect still dominates in D(2)O, 1,4-dioxane-d(8), methanol-d(4), and ethanol-d(6) (96, 89, 85, and 83% gauche-hydroxyls respectively). The observed preference for the gauche-hydroxyl rotamers is believed to stem primarily from hyperconjugative sigma(C--H) --> sigma*(C--OH) interactions.

Removal of phosphate using copper-loaded polymeric ligand exchanger prepared by radiation grafting of polypropylene/polyethylene (PP/PE) nonwoven fabric

NASA Astrophysics Data System (ADS)

Barsbay, Murat; Kavaklı, Pınar Akkaş; Güven, Olgun

2010-03-01

A novel polymeric ligand exchanger (PLE) was prepared for the removal of phosphate ions from water. 2,2'-dipyridylamine (DPA), a bidentate ligand forming compound with high coordination capacity with a variety of metal ions was bound to glycidyl methacrylate (GMA) grafted polypropylene/polyethylene (PP/PE) nonwoven fabric synthesized by radiation-induced grafting technique. DPA attachment on epoxy ring of GMA units was tested in different solvents, i.e. methanol, ethanol, dioxane and dimethylsulfoxide (DMSO). The highest amount of modification was achieved in dioxane. In order to prepare the corresponding PLE for the removal of phosphate, DPA-immobilized fabric was loaded with Cu(II) ions. Phosphate adsorption experiments were performed in batch mode at different pH (5-9) and phosphate concentrations. The fabric was found to be effective for the removal of phosphate ions. At every stage of preparation and use, the nonwoven fabric was characterized by thermal (i.e. DSC and TGA) and spectroscopic (FTIR) methods. Competitive adsorption experiments were also carried out using two solutions with different concentration levels at pH 7 to see the effect of competing ions. Phosphate adsorption was found to be effective and selective from solutions having trace amounts of competitive anions. It is expected that the novel PLE synthesized can be used for the removal of phosphate ions in low concentrations over a large range of pH.

Synthesis, characterization and photophysical-theoretical analysis of compounds A-π-D. 1. Effect of alkyl-phenyl substituted amines in photophysical properties

NASA Astrophysics Data System (ADS)

Ortega, E.; Montecinos, R.; Cattin, L.; Díaz, F. R.; del Valle, M. A.; Bernède, J. C.

2017-08-01

The study of new dipolar A-π-D molecules, which have an acceptor (A) and donor (D) charge joined by a conjugate bridge, have been an attention focus in the recent years due their different properties. In the current work, a molecular system has been modified in order to compare the effect on properties, such as quantum yield. Thus, two series were generated (alkyl- and alkoxy-substituted) to determine if molecules with tertiary asymmetric amines change their optical properties and whether quantum yield is affected. The different products have been characterized by several techniques such as UV-Vis spectrophotometry, elemental analysis, NMR, FT-IR, mass spectroscopy and fluorescence spectroscopy. Furthermore, their behavior in eight organic solvents, dichloromethane, tetrahydrofuran, ethyl acetate, 1,4-dioxane, acetone, acetonitrile, dimethylformamide and dimethylsulfoxide were experimentally and theoretically studied. The quantum yields were higher for the alkyl-substituted series. Theoretically, the dihedral angles formed between the tertiary amine and carbonyl group moieties have a correlation with quantum yield values, helping to explain why they are higher in non-polar solvents. Consequently, the maximum quantum yield was obtained with (E)-2-cyano-3-(5-((E)-2-(9,9-diethyl-7-(methyl(phenyl)amino)-9H-fluoren-2-yl) vinyl)thiophen-2-yl)acrylic acid (M8-1) in 1,4-dioxane, reaching 98.8%.

A Dioxane Template for Highly Selective Epoxy Alcohol Cyclizations

PubMed Central

Mousseau, James J.; Morten, Christopher J.

2013-01-01

Ladder polyether natural products are a class of natural products denoted by their high functional group density and large number of well-defined stereocenters. They comprise the toxic component of harmful algal blooms (HABs), having significant negative economic and environmental ramifications. However, their mode of action, namely blocking various cellular ion channels, also denotes their promise as potential anticancer agents. Understanding their potential mode of biosynthesis will not only help with developing ways to limit the damage of HABs, but would also facilitate the synthesis of a range of analogues with interesting biological activity. 1,3-Dioxan-5-ol substrates display remarkable ‘enhanced template effects’ in water-promoted epoxide cyclization processes en route to the synthesis of these ladder polyether natural products. In many cases they provide near complete endo to exo selectivity in the cyclization of epoxy alcohols, thereby strongly favouring the formation of tetrahydropyran (THP) over tetrahydrofuran (THF) rings. The effects of various Brønsted and Lewis acidic and basic conditions are explored to demonstrate the superior selectivity of the template over the previously reported THP-based epoxy alcohols. In addition, the consideration of other synthetic routes are also considered with the goal of gaining rapid access to a plethora of potential starting materials applicable towards the synthesis of ladder polyethers. Finally, cascade sequences with polyepoxides are investigated, further demonstrating the versatility of this new reaction template. PMID:23775936

Fragrant Dioxane Derivatives Identify β1-Subunit-containing GABAA Receptors*

PubMed Central

Sergeeva, Olga A.; Kletke, Olaf; Kragler, Andrea; Poppek, Anja; Fleischer, Wiebke; Schubring, Stephan R.; Görg, Boris; Haas, Helmut L.; Zhu, Xin-Ran; Lübbert, Hermann; Gisselmann, Günter; Hatt, Hanns

2010-01-01

Nineteen GABAA receptor (GABAAR) subunits are known in mammals with only a restricted number of functionally identified native combinations. The physiological role of β1-subunit-containing GABAARs is unknown. Here we report the discovery of a new structural class of GABAAR positive modulators with unique β1-subunit selectivity: fragrant dioxane derivatives (FDD). At heterologously expressed α1βxγ2L (x-for 1,2,3) GABAAR FDD were 6 times more potent at β1- versus β2- and β3-containing receptors. Serine at position 265 was essential for the high sensitivity of the β1-subunit to FDD and the β1N286W mutation nearly abolished modulation; vice versa the mutation β3N265S shifted FDD sensitivity toward the β1-type. In posterior hypothalamic neurons controlling wakefulness GABA-mediated whole-cell responses and GABAergic synaptic currents were highly sensitive to FDD, in contrast to β1-negative cerebellar Purkinje neurons. Immunostaining for the β1-subunit and the potency of FDD to modulate GABA responses in cultured hypothalamic neurons was drastically diminished by β1-siRNA treatment. In conclusion, with the help of FDDs we reveal a functional expression of β1-containing GABAARs in the hypothalamus, offering a new tool for studies on the functional diversity of native GABAARs. PMID:20511229

Fragrant dioxane derivatives identify beta1-subunit-containing GABAA receptors.

PubMed

Sergeeva, Olga A; Kletke, Olaf; Kragler, Andrea; Poppek, Anja; Fleischer, Wiebke; Schubring, Stephan R; Görg, Boris; Haas, Helmut L; Zhu, Xin-Ran; Lübbert, Hermann; Gisselmann, Günter; Hatt, Hanns

2010-07-30

Nineteen GABA(A) receptor (GABA(A)R) subunits are known in mammals with only a restricted number of functionally identified native combinations. The physiological role of beta1-subunit-containing GABA(A)Rs is unknown. Here we report the discovery of a new structural class of GABA(A)R positive modulators with unique beta1-subunit selectivity: fragrant dioxane derivatives (FDD). At heterologously expressed alpha1betaxgamma2L (x-for 1,2,3) GABA(A)R FDD were 6 times more potent at beta1- versus beta2- and beta3-containing receptors. Serine at position 265 was essential for the high sensitivity of the beta1-subunit to FDD and the beta1N286W mutation nearly abolished modulation; vice versa the mutation beta3N265S shifted FDD sensitivity toward the beta1-type. In posterior hypothalamic neurons controlling wakefulness GABA-mediated whole-cell responses and GABAergic synaptic currents were highly sensitive to FDD, in contrast to beta1-negative cerebellar Purkinje neurons. Immunostaining for the beta1-subunit and the potency of FDD to modulate GABA responses in cultured hypothalamic neurons was drastically diminished by beta1-siRNA treatment. In conclusion, with the help of FDDs we reveal a functional expression of beta1-containing GABA(A)Rs in the hypothalamus, offering a new tool for studies on the functional diversity of native GABA(A)Rs.

In-liquid Plasma. A stable light source for advanced oxidation processes in environmental remediation

NASA Astrophysics Data System (ADS)

Tsuchida, Akihiro; Shimamura, Takeshi; Sawada, Seiya; Sato, Susumu; Serpone, Nick; Horikoshi, Satoshi

2018-06-01

A microwave-inspired device that generates stable in-liquid plasma (LP) in aqueous media and emits narrow light emission lines at 280-320 nm, 660 nm and 780 nm is examined as a light source capable of driving photochemical reactions and advanced oxidation processes in wastewater treatments. The microwave-driven lighting efficiency was improved by decompressing the inside of the reaction vessel, which resulted in lowering the incident power of the microwaves and suppressed the deterioration of the microwave irradiation antenna. This protocol made it possible to generate continuous stable plasma in water. Evaluation of the LP device was carried out by revisiting the decomposition of 1,4-dioxane in aqueous media against the use of such other conventional water treatment processes as (i) UV irradiation alone, (ii) TiO2-assisted photocatalysis with UV irradiation (UV/TiO2), (iii) oxidation with sodium hypochlorite (NaClO), and (iv) UV-assisted decomposition in the presence of NaClO (UV/NaClO). The in-liquid plasma technique proved superior to these four other methods. The influence of pH on the LP protocol was ascertained through experiments in acidified (HCl and H2SO4) and alkaline (NaOH and KOH) aqueous media. Except for H2SO4, decomposition of 1,4-dioxane was enhanced in both acidic and alkaline media.

Effect of hydrostatic pressure, temperature, and solvent on the rate of the Diels-Alder reaction between 9,10-anthracenedimethanol and maleic anhydride

NASA Astrophysics Data System (ADS)

Kiselev, V. D.; Kornilov, D. A.; Anikin, O. V.; Latypova, L. I.; Konovalov, A. I.

2017-03-01

The rate of the reaction between 9,10-anthracenedimethanol and maleic anhydride in 1,4-dioxane, acetonitrile, trichloromethane, and toluene is studied at 25, 35, 45°C in the pressure range of 1-1772 bar. The rate constants, enthalpies, entropies and activation volumes are determined. It is shown that the rate of reaction with 9,10-anthracenedimethanol is approximately one order of magnitude higher than with 9-anthracenemethanol.

Thermospray Liquid Chromatography/Mass Spectrometry of Mustard and Its Metabolites

DTIC Science & Technology

1989-05-01

MONITORING ORGANIZATION REPORT NUMBER(S) CRDEC-TR-066 6a. NAME OF PERFORMING ORGANIZATION 6b OFFICE SYMBOL 7a. NAME OF MONITORING ORGANIZATION (If applicable...see reverse 6c- ADDRESS (Cty, State, and ZIP Code) 7b. ADDRESS (City, State, and ZIP Code) Ba. NAME OF FUNDING/SPONSORING 8b OFFICE SYMBOL 9...Ather und Thioather in Dioxan- Wasser -Gemischen," Chem, Ber. Vol. 81, p 123 (1948). 2. Capon, B., and McManus, S. P., Neighboring Group Participation

Minimizing the amount of nitromethane in palladium-catalyzed cross-coupling with aryl halides.

PubMed

Walvoord, Ryan R; Kozlowski, Marisa C

2013-09-06

A method for the formation of arylnitromethanes is described that employs readily available aryl halides or triflates and small amounts of nitromethane in a dioxane solvent, thereby reducing the hazards associated with this reagent. Specifically, 2-10 equiv (1-5% v/v) of nitromethane can be employed in comparison to prior work that used nitromethane as solvent (185 equiv). The present transformation provides high yields at relatively low temperatures and tolerates an array of functionality, including heterocycles and substantial steric encumbrance.

High Energy Halogen Chemistry.

DTIC Science & Technology

1978-01-01

underwent addition of triflic acid and of hydrochloric acid . The oxetane was polymerized ~zith phosphorous pentaflucride to ~lve a polymer stable to 2900...in aqueous dioxane . The oxetane was not affected by boron trifluoride etherate In chloroform, or by methanolic solutions of sulfuric or triflic acids ...concentrated hydrochloric acid to give 3-chloro-2-fluoro-2-nitro-l-propanol. NO • i 2 NO2OH CF I + CF SOH— 3 CF SO OCH CCH OH O OH ~ 3 3 2 2~ 2 F NO NO

Electrical Microengineering of Redox Enzymes

DTIC Science & Technology

1994-03-31

coating applied to the electrode 41 to prevent lose of mediator graphite foil potassium -~0.02a 0.03  electrolyte wus dioxane with 15% 42...hexacyanoferrats(ll)d aqueous buffer carbon fiber’ none h 40-5000 biotin/avidin complex used to obtain a 43 surface layer of HRP Pt organic metal, potassium ...OFFICE OF NAVAL RESEARCH AD-A279 015 FINAL REPORT FOR CONTRACT NOOO 14-91 -J- 1656 R&T CODE 413h007---05 ELECTRICAL MICROENGINEERING OF REDOX ENZYMES

RDT&E for Emerging Contaminants

DTIC Science & Technology

2010-06-01

Perchlorate ● NDMA ● 1,4-Dioxane ● PFCs 8 Perchlorate Issue ● Broad Use & Occurrence  DoD - Rocket propellant - Insensitive munitions  Pyrotechnics and...and 18O -20 -15 -10 -5.0 0.0 5.0 -30 -25 -20 -15 -10 -5 0 5 10 Laboratory Military Natural Herbicides Gunpowder Road Flares Taiwan 3 7 C l 18 O 27 NDMA ...Toxicology  NDMA is a potent mutagen, teratogen, & carcinogen.  EPA 10-6 Lifetime Cancer Risk = 0.7 ng/L.  California DHS; 10 ng/L Action

ON THE SEPARATION OF VANADIUM, MOLYBDENUM AND TUNGSTEN BY MEANS OF PAPER CHROMATOGRAPHY. PART I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tzou, S.; Liang, S.

1959-02-01

Molybdenum, tangsten, and vanadium are separated by chromatography as per-acids, and then detected with tannin solution. Of the seven solvents tested, n-butanolhydrogen peroxide-nitric acid mixtures offer the best separations. With the addition of dioxane, the R/sub F/ values of these elements increase, while vanadium and tungsten spots overlap. The formation of per-acids avoids the retainment of tungsten on the original spot and the tailings of vanadium and molybdenum spots. (B.O.G.)

Iodine-catalyzed sp³ C-H bond activation by selenium dioxide: synthesis of diindolylmethanes and di(3-indolyl)selanides.

PubMed

Naidu, P Seetham; Majumder, Swarup; Bhuyan, Pulak J

2015-11-01

An efficient reaction protocol was developed for the synthesis of several diindolylmethane derivatives via the [Formula: see text] C-H bond activation of aryl methyl ketones by [Formula: see text] and indoles in the presence of catalytic amounts of [Formula: see text] at 80 [Formula: see text] using dioxane as solvent. Unexpectedly, an interesting class of di(3-indolyl)selenide compounds was isolated when the reaction was carried out at room temperature.

Spectroscopic and pH-metric studies of the complexation of 3-[2-(4-methylquinolin-2-yl)hydrazono]butan-2-one oxime compound.

PubMed

Seleem, H S; El-Inany, G A; Mousa, M; Hanafy, F I

2010-05-01

The electronic absorption spectra of the oximic quinolinyl hydrazone (MHQ; H(2)L) and its Co(II) and Cu(II)-complexes have been studied in Britton-Rhobinson buffer solutions of varying pH's in 75% dioxane-water. The dissociation constant of the hydrazone (pK(H)) as well as the stability constants (logK) of its chelates were determined spectrophotometrically and pH-metrically. The obtained data are in good agreement. Beer's law is valid in the ranges (0.64-6.99) and (2.36-6.48)mug/mL for Cu(II) and Co(II)-ions, respectively. On the other hand, the pK(H) and logK were determined pH-metrically in 75% solvent-water; (solvent=dioxane, ethanol, methanol and isopropanol). The variation of pK(H) or logK as a function of solvent parameters viz. 1/D, E(T), AN and pi* was used to evaluate the dissociation and stability constants in the aqueous medium. Furthermore, the reaction of the oximic hydrazone (H(2)L) with copper(II)-nitrate and chloride in addition to copper(I)-iodide afforded square planar mononuclear and binuclear complexes in which the oximic hydrazone showed three different modes of bonding. The obtained complexes reflect the strong bridging ability of the oximato group as well as its ambidentate and flexidentate characters. Copyright 2010 Elsevier B.V. All rights reserved.

Natural deep eutectic solvents as eco-friendly and sustainable dilution medium for the determination of residual organic solvents in pharmaceuticals with static headspace-gas chromatography.

PubMed

Wang, Meilian; Fang, Sheng; Liang, Xianrui

2018-06-04

Reported here is a simple and rapid static headspace gas chromatography (SHS-GC) method for the determination of trace solvents including ethanol, isopropanol, n-butanol, 1,4-dioxane, tetrahydrofuran, acetonitrile, methanol and acetone which commonly used in drug production process. Natural deep eutectic solvents (NADESs) are firstly used as the matrix medium for this method, which provided high sensitivity for residual solvents detection. With the optimized method, validation experiments were performed and the data showed excellent linearity for all the solvents (R 2 ≥ 0.999, n = 7). The limits of detection (LOD) for ethanol, isopropanol, n-butanol, 1,4-dioxane, tetrahydrofuran, acetonitrile, methanol and acetone are 0.09, 0.08, 0.07, 0.11, 0.06, 0.10, 0.12 and 0.08 μg g -1 , respectively. Accuracy was checked by a recovery experiment at three different levels, and the recoveries of the tested solvents were ranged from 94.3% to 105.4%. The relative standard deviation (RSD) of each solvent for intra- and inter-day precision is in the range of 0.85 to 3.65 and 1.51 to 4.53, respectively. The developed approach can be readily used for determination of the residual solvents in six active pharmaceutical ingredients including pramipexole dihydrochloride, rivaroxaban, lisinopril, ramipril, imatinib mesylate and sitagliptin. Copyright © 2018 Elsevier B.V. All rights reserved.

Emerging Water Contaminants: Technical, Legal and Policy Challenges

NASA Astrophysics Data System (ADS)

Deeb, R. A.; Kresic, N.; Laugier, M. C.; Kavanaugh, M. C.

2002-12-01

Approximately 120 new chemicals are created each year due to ever-improving industry and technology markets. Releases of new contaminants into the environment can occur during production, use and disposal of these chemicals thereby leading to potential contamination of water supply sources. Very few emerging contaminants are regulated. In addition, knowledge gaps regarding emerging contaminants include lack health effects, occurrence (either because these compounds are not measured or because concentrations are below detection limits of readily available analytical techniques) and fate and transport in the environment especially with regards to mobility and persistence. The sources of these compounds are numerous. One source is treated wastewater, which is re-injected into groundwater aquifers for indirect potable reuse purposes. Emerging compounds of concern can be classified in various classes. This presentation will focus on contaminants, which have emerged in the last 10 years including pharmaceuticals (antibiotics/drugs), personal care products (polycyclic musks), pesticides/herbicides, industrial solvents (1,4-dioxane), gasoline additives (MTBE), disinfection byproducts such as NDMA (N-nitrosodimethylamine), and inorganic compounds such as perchlorate and arsenic. This presentation will present technical, legal and legislative challenges posed by the presence of these contaminants in water. Background information including chemical's history of use, sources in the environments, nationwide occurrence, physical and chemical properties, behavior in the environment and technologies for removal from soil and water will be presented. In addition, case studies on MTBE, pharmaceuticals and personal care products, 1,4-dioxane, arsenic and NDMA will be discussed.

Hydrogen transfer reduction of polyketones catalyzed by iridium complexes: a novel route towards more biocompatible materials.

PubMed

Milani, Barbara; Crottib, Corrado; Farnetti, Erica

2008-09-14

Transfer hydrogenation from 2-propanol to CO/4-methylstyrene and CO/styrene polyketones was catalyzed by [Ir(diene)(N-N)X] (N-N = nitrogen chelating ligand; X = halogen) in the presence of a basic cocatalyst. The reactions were performed using dioxane as cosolvent, in order to overcome problems due to low polyketone solubility. The polyalcohols were obtained in yields up to 95%, the conversions being markedly dependent on the nature of the ligands coordinated to iridium as well as on the experimental conditions.

Minimizing the Amount of Nitromethane in Palladium Catalyzed Cross Coupling with Aryl Halides

PubMed Central

Walvoord, Ryan R.; Kozlowski, Marisa C.

2013-01-01

A method for the formation of arylnitromethanes is described that employs readily available aryl halides or triflates and small amounts of nitromethane in a dioxane solvent, thereby reducing the hazards associated with this reagent. Specifically, 2–10 equivalents (1–5% v/v) of nitromethane can be employed in comparison to prior work that used nitromethane as solvent (185 equivalents). The present transformation provides high yields at relatively low temperatures and tolerates an array of functionality, including heterocycles and substantial steric encumbrance. PMID:23895411

Developing and Validating Genetic Catabolic Probes for Monitored Natural Attenuation of 1,4-Dioxane with a One-Year Timeframe

DTIC Science & Technology

2014-04-01

Psed_0815_F TTC CCG CCG TAG GAC AGG GA Psed_0815_R GTT GCC GTG GTT GTG CAG CA tmo3A Psed_1155_F CTC TCC GAG TAC GCC GCC TG Psed_1155_R GCC ATG TCG...GAG CTC GTC GA tmo2A Psed_1436_F CTC TGC AGC CTG TGC CAC CT Psed_1436_R CCC GTT GTG GGT GAG CGA GT tmo4A Psed_6062_F GCT CCA TGA ACT GCT TGA

Interconversion algorithm between mechanical and dielectric relaxation measurements for acetate of cis- and trans-2-phenyl-5-hydroxymethyl-1,3-dioxane.

PubMed

Garcia-Bernabé, A; Lidón-Roger, J V; Sanchis, M J; Díaz-Calleja, R; del Castillo, L F

2015-10-01

The dielectric and mechanical spectroscopies of acetate of cis- and trans-2-phenyl-5-hydroxymethyl-1,3-dioxane are reported in the frequency domain from 10(-2) to 10(6)Hz. This ester has been selected in this study for its predominant α relaxation with regard to the β relaxation, which can be neglected. This study consists of determining an interconversion algorithm between dielectric and mechanical measurements, given by using a relation between rotational and translational complex viscosities. These important viscosities were obtained from measures of the dielectric complex permittivity and by dynamic mechanical analysis, respectively. The definitions of rotational and translational viscosities were evaluated by means of fractional calculus, by using the fit parameters of the Havriliak-Negami empirical model obtained in the dielectric and mechanical characterization of the α relaxation. This interconversion algorithm is a generalization of the break of the Stokes-Einstein-Debye relationship. It uses a power law with an exponent defined as the shape factor, which modifies the translational viscosity. Two others factors are introduced for the interconversion, a shift factor, which displaces the translational viscosity in the frequency domain, and a scale factor, which makes equal values of the two viscosities. In this paper, the shape factor has been identified as the relation between the slopes of the moduli of the complex viscosities at higher frequency. This is interpreted as the degree of kinetic coupling between the molecular rotation and translational movements. Alternatively, another interconversion algorithm has been expressed by means of dielectric and mechanical moduli.

Photolysis of Mono- and Dichloramines in UV/Hydrogen Peroxide: Effects on 1,4-Dioxane Removal and Relevance in Water Reuse.

PubMed

Patton, Samuel; Romano, Mariano; Naddeo, Vincenzo; Ishida, Kenneth P; Liu, Haizhou

2018-06-05

Growing demands and increasing scarcity of fresh water resources necessitate potable water reuse, which has been implemented with the aid of UV-based advanced oxidation processes (UV/AOPs) that remove potentially hazardous trace organic contaminants from reclaimed water. During the potable reuse treatment process, chloramines are added to prevent membrane fouling that are carried over to the UV/AOP, where hydrogen peroxide (H 2 O 2 ) is commonly added. However, the impact of chloramines on the photolysis of H 2 O 2 and the overall performance of the UV/AOP remains unknown. This study investigated the impacts of the photochemistry of monochloramine (NH 2 Cl) and dichloramine (NHCl 2 ) associated with the photolysis of H 2 O 2 on the degradation of 1,4-dioxane (1,4-D), a trace organic contaminant ubiquitous in recycled water. Results indicated that NH 2 Cl and NHCl 2 alone functioned as oxidants upon UV photolysis, which produced HO • and Cl 2 •- as the two primary oxidative radicals. The speciation of chloramines did not have a significant impact on the degradation kinetics. The inclusion of monochloramine in UV/H 2 O 2 greatly decreased 1,4-D removal efficiency. HO • was the major radical in the mixed H 2 O 2 /chloramine system. Results from this study suggest that recognizing the existence of chloramines in UV/H 2 O 2 systems is important for predicting UV/AOP performance in the treatment train of potable reuse.

Retinoid quantification by HPLC/MS(n)

NASA Technical Reports Server (NTRS)

McCaffery, Peter; Evans, James; Koul, Omanand; Volpert, Amy; Reid, Kevin; Ullman, M. David

2002-01-01

Retinoic acid (RA) mediates most of the biological effects of vitamin A that are essential for vertebrate survival. It acts through binding to receptors that belong to the nuclear receptor transcription factor superfamily (Mangelsdorf et al. 1994). It is also a highly potent vertebrate teratogen. To determine the function and effects of endogenous and exogenous RA, it is important to have a highly specific, sensitive, accurate, and precise analytical procedure. Current analyses of RA and other retinoids are labor intensive, of poor sensitivity, have limited specificity, or require compatibility with RA reporter cell lines (Chen et al. 1995. BIOCHEM: Pharmacol. 50: 1257-1264; Creech Kraft et al. 1994. BIOCHEM: J. 301: 111-119; Lanvers et al. 1996. J. Chromatogr. B Biomed. Appl. 685: 233-240; Maden et al. 1998. DEVELOPMENT: 125: 4133-4144; Wagner et al. 1992. DEVELOPMENT: 116: 55-66). This paper describes an HPLC/mass spectrometry/mass spectrometry product ion scan (HPLC/MS(n)) procedure for the analysis of retinoids that employs atmospheric pressure chemical ionization MS. The retinoids are separated by normal-phase column chromatography with a linear hexane-isopropanol-dioxane gradient. Each retinoid is detected by a unique series of MS(n) functions set at optimal collision-induced dissociation energy (30% to 32%) for all MS(n) steps. The scan events are divided into three segments, based on HPLC elution order, to maximize the mass spectrometer duty cycle. The all-trans, 9-cis, and 13-cis RA isomers are separated, if desired, by an isocratic hexane-dioxane-isopropanol mobile phase. This paper describes an HPLC/MS(n) procedure possessing high sensitivity and specificity for retinoids.

Polarization studies on zinc in hydrochloric acid solution containing some organic solvents

NASA Astrophysics Data System (ADS)

Mohamed, A. K.

1999-05-01

The corrosion behaviour of zinc metal in some organic solvents was tested electrochemically using galvanometric polarization measurements. The results showed that the studied organic solvents act as mixed type inhibitors. The inhibition was assumed to occur via physical adsorption of the inhibitor molecules fitting a Temkin's isotherm. The inhibition eficiency of the solvents increase in the order: glycerol>ethylene glycol>DMSO>dioxane. This order is not affected by the variation in temperature in the range 35-55 circC. The increase in temperature was found to increase the corrosion in absence and in presence of inhibitors. Some thermodynamic parameters for adsorption were also computed and discussed. Le comportement de corrosion du zinc métallique dans certains solvants organiques a été testé électrochimiquement en utilisant les mesures de polarisation galvanométrique. Les résultats ont montré que les solvants organiques étudiés agissent comme des inhibiteurs de type mixte. L'inhibition semble se produire par l'adsorption physique des molécules inhibitrices selon une isotherme de Temkin. L'efficacité d'inhibition des solvants augmente dans l'ordre suivant : glycérol>éthylène glycol>DMSO>dioxane. Cet ordre n'est pas affecté par une variation de température dans l'intervalle compris entre 35 et 55 circC. La corrosion augmente avec la température, en absence ou en présence d'inhibiteurs. Certains paramètres thermodynamiques d'adsorption ont été calculés et discutés.

A new ether-based electrolyte for dendrite-free lithium-metal based rechargeable batteries

PubMed Central

Miao, Rongrong; Yang, Jun; Xu, Zhixin; Wang, Jiulin; Nuli, Yanna; Sun, Limin

2016-01-01

A new ether-based electrolyte to match lithium metal electrode is prepared by introducing 1, 4-dioxane as co-solvent into lithium bis(fluorosulfonyl)imide/1,2-dimethoxyethane solution. Under the synergetic effect of solvents and salt, this simple liquid electrolyte presents stable Li cycling with dendrite-free Li deposition even at relatively high current rate, high coulombic efficiency of ca. 98%, and good anodic stability up to ~4.87 V vs Li RE. Its excellent performance will open up a new possibility for high energy-density rechargeable Li metal battery system. PMID:26878890

Forage lignins: isolation, characterization and degradation in the gastrointestinal trace of ruminants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quiroz, R.A.

1987-01-01

A series of experiments were conducted to investigate the structural composition of forage lignins, structural changes of lignins in the gastrointestinal tract, alkali delignification kinetics and the use of core lignin components as an internal marker. Three species were selected to represent different forage types; alfalfa (Medicago sativa L.), a temperate perennial legume, tall fescue (Festuca arundinacea Schreb.), a temperate perennial grass and coastal bermudagrass (Cynodon dactylon L. Pers.), a tropical perennial grass. Alkaline lignins soluble in 1,4-dioxane, from forage and feces, were isolated and characterized using /sup 13/C nuclear magnetic resonance spectroscopy and nitrobenzene oxidation.

Lupane, friedelane, oleanane, and ursane triterpenes from the stem of Siphonodon celastrineus Griff.

PubMed

Kaweetripob, Wirongrong; Mahidol, Chulabhorn; Prawat, Hunsa; Ruchirawat, Somsak

2013-12-01

Twenty-one triterpenes consisting of a lupane derivative, two friedelanes, an oleanane derivative, and 17 ursane-type triterpenoids, together with three known triterpenes, three sterols, a fatty acid, a sesquiterpene alkaloid, and a glycerol derivative, were isolated from the stem of Siphonodon celastrineus. Their structures were characterized by various spectroscopic techniques, as well as comparison with literature data. Twenty-seven metabolites of these were evaluated for cytotoxic activity against six human cancer cell lines. The biosynthetic formation of a 1,4-dioxane bridge is also discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

Cyclic Disilylated and Digermylated Germylenes

PubMed Central

2013-01-01

The preparation of triethylphosphine adducts of cyclic disilylated or digermylated germylenes was achieved by reaction of 1,4-dipotassio-1,1,4,4-tetrakis(trimethylsilyl)tetramethyltetrasilane with GeBr2·(dioxane) and PEt3. Phosphine abstraction with B(C6F5)3 allowed formation of the base-free germylenes, which undergo 1,2-trimethylsilyl shifts to the germylene atom to form the respective silagermene or digermene, which further dimerize in [2 + 2] cycloadditions to tricyclic compounds. The reasons responsible for the germylenes’ completely different reactivities in comparison to the previously studied analogous stannylenes and plumbylenes were elucidated in a theoretical study. PMID:23874054

Visible-Light-Promoted Metal-Free Aerobic Oxidation of Primary Amines to Acids and Lactones.

PubMed

Cheng, Xiaokai; Yang, Bo; Hu, Xingen; Xu, Qing; Lu, Zhan

2016-12-05

A unique metal-free aerobic oxidation of primary amines via visible light photocatalytic double carbon-carbon bonds cleavage and multi carbon-hydrogen bonds oxidation was observed. Aerobic oxidation of primary amines could be controlled to afford acids by using dioxane with 18 W CFL, and lactones by using DMF with 8 W green LEDs, respectively. A plausible mechanism was proposed based on control experiments. This observation showed direct evidences for the fragmentation in the aerobic oxidation of aliphatic primary amines. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Maleimide-functionalized closo-dodecaborate albumin conjugates (MID-AC): Unique ligation at cysteine and lysine residues enables efficient boron delivery to tumor for neutron capture therapy.

PubMed

Kikuchi, Shunsuke; Kanoh, Daisuke; Sato, Shinichi; Sakurai, Yoshinori; Suzuki, Minoru; Nakamura, Hiroyuki

2016-09-10

Maleimide-conjugating closo-dodecaborate sodium form 5c (MID) synthesized by the nucleophilic ring-opening reaction of closo-dodecaborate-1,4-dioxane complex 2 with tetrabutylammonium (TBA) azide was found to conjugate to free SH of cysteine and lysine residues in BSA under physiological conditions, forming highly boronated BSA that showed high and selective accumulation in tumor and significant tumor growth inhibition in colon 26 tumor-bearing mice subjected to thermal neutron irradiation. Copyright © 2016 Elsevier B.V. All rights reserved.

Sustainable in situ remediation of recalcitrant organic pollutants in groundwater with controlled release materials: A review.

PubMed

O'Connor, David; Hou, Deyi; Ok, Yong Sik; Song, Yinan; Sarmah, Ajit K; Li, Xuanru; Tack, Filip M G

2018-06-06

The removal of recalcitrant organic pollutants in groundwater is a challenge being faced around the world. Achieving effective long-term remediation of contaminated aquifers faces a variety of significant issues such as back diffusion, tailing, and rebound. In recent years, some researchers have proposed the use of controlled release materials (CRMs) as a new approach to counteracting such issues. The novelty of CRMs lies in that they release their active products slowly, over prolonged periods of time, in order to sustain in situ treatments and long-term effectiveness. Here we review the main constituents of CRMs, analyze their production, characterization, and applications, with a focus on reaction mechanisms, effectiveness, and secondary effects. This review shows that the reactive components of CRMs most commonly involve either: (i) chemical oxidants to treat contaminants such as TCE, PCE, BTEX, and 1,4-Dioxane; (ii) sources of dissolved oxygen to stimulate aerobic biodegradation of contaminants such as BTEX and 1,4-Dioxane; or, (iii) substrates that stimulate reductive dechlorination of contaminants such as TCE and 1,2-DCA. It was found that in some studies, CRMs provided sustained delivery of CRM treatment reagents over several years, and achieved complete contaminant removal. However, lower removal rates were apparent in other cases, which may be ascribed to insufficient dispersion in the subsurface. There are a relatively limited number of field-scale applications of CRMs in contaminated land remediation. Those conducted to date suggest that CRMs could prove to be an effective future remediation strategy. Lessons learned from field applications, suggestions for future research directions, and conclusions are put forward in this review. Copyright © 2018 Elsevier B.V. All rights reserved.

The synthesis, structure and properties of N-acetylated derivatives of ethyl 3-amino-1H-pyrazole-4-carboxylate.

PubMed

Kusakiewicz-Dawid, Anna; Masiukiewicz, Elzbieta; Rzeszotarska, Barbara; Dybała, Izabela; Kozioł, Anna Eugenia; Broda, Małgorzata Anna

2007-05-01

Ethyl 3-amino-1H-pyrazole-4-carboxylate (1) was yielded through total synthesis and reacted with acetic anhydride to give the acetylated products 2-6. Compounds 1-6 were studied with HPLC, X-ray, FT-IR, (1)H-NMR, (13)C-NMR and MS. Acetylation was carried out in solvents of various polarity, namely; chloroform; dioxane; DMF; acetic anhydride, at room temperature and at boiling points; and in the presence and absence of DMAP. The acetylated products are mainly nitrogen atoms in the ring. The position of the ring proton in the solution was based on NOESY; multinuclear HMBC, HSQC spectra and calculations. For equivalent amounts (1-1.5 mol) of acetic anhydride at room temperature two products of monoacetylation are produced in the ring: 2 and 3, ca. 2 : 1 and at the same time only small amount of the third product of monoacetylated, 5 in DMF, as well the product diacetylated, 4. The greatest amount of the product 4 is produced during the reaction with chloroform. However, in this solvent and in dioxane no product 5 is produced. Compound 2 is, largely, formed in dimethylformamide, in the presence DMAP, 0.2 eq. In the presence of this catalytic base, for the first hour, there is a mixture 2 and 3 to the ratio ca. 95 : 5. With 8 eq of Ac(2)O at reflux, after another hour, the compounds 3, 4 and 6 appear about equal amounts. After a longer time, the compound, which appears most in this mixture is triacetylated derivative 6. The structural and spectroscopic characteristics of compounds 1-6 have been given and the methods for their preparation have been provided.

Polymer scaffolds with no skin-effect for tissue engineering applications fabricated by thermally induced phase separation.

PubMed

Kasoju, Naresh; Kubies, Dana; Sedlačík, Tomáš; Janoušková, Olga; Koubková, Jana; Kumorek, Marta M; Rypáček, František

2016-01-11

Thermally induced phase separation (TIPS) based methods are widely used for the fabrication of porous scaffolds for tissue engineering and related applications. However, formation of a less-/non-porous layer at the scaffold's outer surface at the air-liquid interface, often known as the skin-effect, restricts the cell infiltration inside the scaffold and therefore limits its efficacy. To this end, we demonstrate a TIPS-based process involving the exposure of the just quenched poly(lactide-co-caprolactone):dioxane phases to the pure dioxane for a short time while still being under the quenching strength, herein after termed as the second quenching (2Q). Scanning electron microscopy, mercury intrusion porosimetry and contact angle analysis revealed a direct correlation between the time of 2Q and the gradual disappearance of the skin, followed by the widening of the outer pores and the formation of the fibrous filaments over the surface, with no effect on the internal pore architecture and the overall porosity of scaffolds. The experiments at various quenching temperatures and polymer concentrations revealed the versatility of 2Q in removing the skin. In addition, the in vitro cell culture studies with the human primary fibroblasts showed that the scaffolds prepared by the TIPS based 2Q process, with the optimal exposure time, resulted in a higher cell seeding and viability in contrast to the scaffolds prepared by the regular TIPS. Thus, TIPS including the 2Q step is a facile, versatile and innovative approach to fabricate the polymer scaffolds with a skin-free and fully open porous surface morphology for achieving a better cell response in tissue engineering and related applications.

An investigation of the role of water on retrograde/condensation reactions and enhanced liquefaction yields. Quarterly progress report, January 1, 1994--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miknis, F.P.; Netzel, D.A.

The results of coal swelling measurements using 1,4-dioxane as the swelling reagent for premoisturized coals (raw) and coal dried thermally, chemically, and with microwave radiation are presented. An increase in the swelling ratio relative to raw coal indicates a decrease in the amount of cross-linking in the coal. Conversely, a decrease in the ratio indicates an increase in cross-linking. The extent of cross-linking (as measured by 1,4-dioxane) for Texas, Black Thunder, and Eagle Butte Coals are about the same. Illinois {number_sign}6 coal appears to have less cross-linking relative to the other three coals. These results are expected on the basismore » of coal rank. The increase in cross linking is most pronounced for coals dried thermally and with microwave radiation. A decrease in the swelling ratios for all four coals suggests that cross-linking had occurred possibly due to partial devolatilization process. However, low temperature, chemical dehydration of the coals causes only a small or no change in the internal structure for Texas and Illinois {number_sign}6 coals whereas a significant decrease in the cross-linking structure for the Black Thunder and Eagle Butte coals is observed. It is possible that the solvent (CH{sub 3}OH) and products resulting from the chemical dehydrating (acetone and methanol) occupy the surface sites that water had before the reaction and thus preventing cross-linking to occur. These reagents can also promote swelling of coals and may account for some of the decrease in the cross-linking of the coal structure observed for the chemically dried coals.« less

RAFT Dispersion Alternating Copolymerization of Styrene with N-Phenylmaleimide: Morphology Control and Application as an Aqueous Foam Stabilizer

PubMed Central

2016-01-01

We report a new nonaqueous polymerization-induced self-assembly (PISA) formulation based on the reversible addition–fragmentation chain transfer (RAFT) dispersion alternating copolymerization of styrene with N-phenylmaleimide using a nonionic poly(N,N-dimethylacrylamide) stabilizer in a 50/50 w/w ethanol/methyl ethyl ketone (MEK) mixture. The MEK cosolvent is significantly less toxic than the 1,4-dioxane cosolvent reported previously [YangP.; Macromolecules2013, 46, 8545−8556]. The core-forming alternating copolymer block has a relatively high glass transition temperature (Tg), which leads to vesicular morphologies being observed during PISA, as well as the more typical sphere and worm phases. Each of these copolymer morphologies has been characterized by transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS) studies. TEM studies reveal micrometer-sized elliptical particles with internal structure, with SAXS analysis suggesting an oligolamellar vesicle morphology. This structure differs from that previously reported for a closely related PISA formulation utilizing a poly(methacrylic acid) stabilizer block for which unilamellar platelet-like particles are observed by TEM and SAXS. This suggests that interlamellar interactions are governed by the nature of the steric stabilizer layer. Moreover, using the MEK cosolvent also enables access to a unilamellar vesicular morphology, despite the high Tg of the alternating copolymer core-forming block. This was achieved by simply conducting the PISA synthesis at a higher temperature for a longer reaction time (80 °C for 24 h). Presumably, MEK solvates the core-forming block more than the previously utilized 1,4-dioxane cosolvent, which leads to greater chain mobility. Finally, preliminary experiments indicate that the worms are much more efficient stabilizers for aqueous foams than either the spheres or the oligolamellar elliptical vesicles. PMID:27708458

Potential for cometabolic biodegradation of 1,4-dioxane in aquifers with methane or ethane as primary substrates.

PubMed

Hatzinger, Paul B; Banerjee, Rahul; Rezes, Rachael; Streger, Sheryl H; McClay, Kevin; Schaefer, Charles E

2017-12-01

The objective of this research was to evaluate the potential for two gases, methane and ethane, to stimulate the biological degradation of 1,4-dioxane (1,4-D) in groundwater aquifers via aerobic cometabolism. Experiments with aquifer microcosms, enrichment cultures from aquifers, mesophilic pure cultures, and purified enzyme (soluble methane monooxygenase; sMMO) were conducted. During an aquifer microcosm study, ethane was observed to stimulate the aerobic biodegradation of 1,4-D. An ethane-oxidizing enrichment culture from these samples, and a pure culture capable of growing on ethane (Mycobacterium sphagni ENV482) that was isolated from a different aquifer also biodegraded 1,4-D. Unlike ethane, methane was not observed to appreciably stimulate the biodegradation of 1,4-D in aquifer microcosms or in methane-oxidizing mixed cultures enriched from two different aquifers. Three different pure cultures of mesophilic methanotrophs also did not degrade 1,4-D, although each rapidly oxidized 1,1,2-trichloroethene (TCE). Subsequent studies showed that 1,4-D is not a substrate for purified sMMO enzyme from Methylosinus trichosporium OB3b, at least not at the concentrations evaluated, which significantly exceeded those typically observed at contaminated sites. Thus, our data indicate that ethane, which is a common daughter product of the biotic or abiotic reductive dechlorination of chlorinated ethanes and ethenes, may serve as a substrate to enhance 1,4-D degradation in aquifers, particularly in zones where these products mix with aerobic groundwater. It may also be possible to stimulate 1,4-D biodegradation in an aerobic aquifer through addition of ethane gas. Conversely, our results suggest that methane may have limited importance in natural attenuation or for enhancing biodegradation of 1,4-D in groundwater environments.

Experimental Investigation and Thermodynamic Assessment of Phase Equilibria in the PLLA/Dioxane/Water Ternary System for Applications in the Biomedical Field.

PubMed

Ruggiero, Flavia; Netti, Paolo Antonio; Torino, Enza

2015-12-01

Fundamental understanding of thermodynamic of phase separation plays a key role in tuning the desired features of biomedical devices. In particular, phase separation of ternary solution is of remarkable interest in processes to obtain biodegradable and biocompatible architectures applied as artificial devices to repair, replace, or support damaged tissues or organs. In these perspectives, thermally induced phase separation (TIPS) is the most widely used technique to obtained porous morphologies and, in addition, among different ternary systems, polylactic acid (PLLA)/dioxane/water has given promising results and has been largely studied. However, to increase the control of TIPS-based processes and architectures, an investigation of the basic energetic phenomena occurring during phase separation is still required. Here we propose an experimental investigation of the selected ternary system by using isothermal titration calorimetric approach at different solvent/antisolvent ratio and a thermodynamic explanation related to the polymer-solvents interactions in terms of energetic contribution to the phase separation process. Furthermore, relevant information about the phase diagrams and interaction parameters of the studied systems are furnished in terms of liquid-liquid miscibility gap. Indeed, polymer-solvents interactions are responsible for the mechanism of the phase separation process and, therefore, of the final features of the morphologies; the knowledge of such data is fundamental to control processes for the production of membranes, scaffolds and several nanostructures. The behavior of the polymer at different solvent/nonsolvent ratios is discussed in terms of solvation mechanism and a preliminary contribution to the understanding of the role of the hydrogen bonding in the interface phenomena is also reported. It is the first time that thermodynamic data of a ternary system are collected by mean of nano-isothermal titration calorimetry (nano-ITC). Supporting Information is available.

Asymmetric synthesis of 5-arylcyclohexenones by rhodium(I)-catalyzed conjugate arylation of racemic 5-(trimethylsilyl)cyclohexenone with arylboronic acids.

PubMed

Chen, Qian; Kuriyama, Masami; Soeta, Takahiro; Hao, Xinyu; Yamada, Ken-ichi; Tomioka, Kiyoshi

2005-09-29

[reaction: see text] A catalytic asymmetric conjugate arylation of racemic 5-(trimethylsilyl)cyclohex-2-enone with arylboronic acids was catalyzed by 3 mol % chiral amidophosphane- or BINAP-Rh(I) in dioxane-water (10:1) to afford trans- and cis-3-aryl-5-(trimethylsilyl)cyclohexanones in high enantioselectivity. Dehydrosilylation of the product mixture with cupric chloride in DMF gave 5-arylcyclohex-2-enones with up to 93% ee in good yield. Enantiofacial selectivity with chiral phosphane-Rh(I) exceeds the trans-diastereoselectivity that is maintained in the achiral or racemic phosphane-Rh(I)-catalyzed conjugate arylation of 5-(trimethylsilyl)cyclohexenone.

Studies on electronic spectral parameters of doped Nd(III) ion with therapeutically important ligands in dioxane solvent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bajaj, Annu, E-mail: annu.bajaj11@gmail.com; Jain, Sushma

2016-05-06

The present investigation is concerened with the studies on electronic spectral parameters viz. Oscillator strength (P), Judd-Ofelt T{sub λ} (λ=2,4,6), Slater-Condon(F{sub K}),Lande(ζ{sub 4F}),Nephelauxetic ratio(β), Bonding parameter (b{sup 1/2}) and Percent covalency parameter (δ%) for Nd(III) ion complexes with the ligands having Nitrogen,Oxygen Sulphur donor sites.The variation in the values of oscillator strength explicitly shows the relative sensitivities of the 4f-4f transition as well as the specific correlation between ligand structures and nature of Nd(III) ligand interaction.

Developing the ISCO Technology Practices Manual: The SERDP/ESTCP ISCO Initiative

DTIC Science & Technology

2010-12-01

8741 mg/L [TCE] / [TCE]o MnO4- and TCE reacting 2nd-order reaction [TCE]o = 1000 mg/L [NOD]o = 0 Temp. = 20C MnO4- = 1311 mg/L k2 = 0.89 L mol -1 s...1 Ea = 78 kJ mol -1 k2 = 0.89 at 20C 0.30 at 10C 7 d TCE[ ] dt = −k2 TCE[ ]1 MnO4 −[ ]1 Source: Siegrist et al. 2001. ● NAPLs can be degraded via...Phenols (e.g., chlorophenols) Ketones Fuel oxygenates (MTBE, TAME) PCBs Alcohols Dioxins /Furans 1,4-dioxane 5 Basic Screening Is the CSM adequately

Serinol: small molecule - big impact

PubMed Central

2011-01-01

The amino alcohol serinol (2-amino-1,3-propanediol) has become a common intermediate for several chemical processes. Since the 1940s serinol was used as precursor for synthesis of synthetic antibiotics (chloramphenicol). In the last years, new scopes of applications were discovered. Serinol is used for X-ray contrast agents, pharmaceuticals or for chemical sphingosine/ceramide synthesis. It can either be obtained by chemical processes based on 2-nitro-1,3-propanediol, dihydroxyacetone and ammonia, dihydroxyacetone oxime or 5-amino-1,3-dioxane, or biotechnological application of amino alcohol dehydrogenases (AMDH) or transaminases. This review provides a survey of synthesis, properties and applications for serinol. PMID:21906364

Optimized multi-step NMR-crystallography approach for structural characterization of a stable quercetin solvate.

PubMed

Filip, Xenia; Miclaus, Maria; Martin, Flavia; Filip, Claudiu; Grosu, Ioana Georgeta

2017-05-10

Herein we report the preparation and solid state structural investigation of the 1,4-dioxane-quercetin solvate. NMR crystallography methods were employed for crystal structure determination of the solvate from microcrystalline powder. The stability of the compound relative to other reported quercetin solvates is discussed and found to be in perfect agreement with the hydrogen bonding networks/supra-molecular architectures formed in each case. It is also clearly shown that NMR crystallography represents an ideal analytical tool in such cases when hydrogen-bonding networks are required to be constrained at a high accuracy level. Copyright © 2017 Elsevier B.V. All rights reserved.

(6)Li-loaded liquid scintillators with pulse shape discrimination.

PubMed

Greenwood, L R; Chellew, N R; Zarwell, G A

1979-04-01

Excellent pulse height and pulse shape discrimination performance has been obtained for liquid scintillators containing as much as 10 wt.% (6)Li-salicylate dissolved in a toluene-methanol solvent system using naphthalene and 9,10 diphenylanthracene as intermediate and secondary solutes. This solution has improved performance at higher (6)Li-loading than solutions in dioxane-water solvent systems, and remains stable at temperatures as low as -10 degrees C. Cells as large as 5 cm in diameter and 15.2 deep have been prepared which have a higher light output for slow neutron detection than (10)B-loaded liquids. Neutron efficiency calculations are also presented.

Radical-mediated reduction of the dithiocarbamate group under tin-free conditions.

PubMed

McMaster, Claire; Bream, Robert N; Grainger, Richard S

2012-06-28

Reductive desulfurisation of dithiocarbamates is conveniently achieved using H(3)PO(2)-Et(3)N-ACCN in refluxing dioxane. Fused and spirocyclic β-lactams, prepared through 4-exo trig carbamoyl radical cyclisation-dithiocarbamate group transfer reactions, are reduced without fragmentation of the strained 4-membered ring. Diethyl tetraacetyl-d-glucopyranosyl dithiocarbamate is selectively reduced with or without acyloxy group migration depending on reaction conditions and choice of reductant. Deuterium incorporation from D(3)PO(2)-Et(3)N is observed for a system involving a nucleophilic radical intermediate, but not in the case of the electrophilic radical obtained through acyloxy group migration on a glucose derivative.

Design of a Facility to Implement a Low Cost Process for Production of NHC

DTIC Science & Technology

1979-05-15

CO4PANY V. i In brief, crude NHC is produced by sequential batch- wise solution processing, initially converting BIO to the sulfide ligand with subsequent...L 1.03 50 214 R-3 (Dibutyl Sulfide ) L 0.84 -112 360 R-4 (Pyridine) L 0.98 - 44 240 1-Octyne L 0.75 -110 260 Acetone L 0.79 -138 134 Methanol L 0.79...R3 -- 25-Octyne- 300 C5 30 TOL 4 NHC -AREA 40 LEGEND: 82 - Diborane R2 - Dioxane B10 - Decaborane R3 - Butyl Sulfide C5 - Pentane MEOH - Methanol C6

From micelle supramolecular assemblies in selective solvents to isoporous membranes.

PubMed

Nunes, Suzana P; Karunakaran, Madhavan; Pradeep, Neelakanda; Behzad, Ali Reza; Hooghan, Bobby; Sougrat, Rachid; He, Haoze; Peinemann, Klaus-Viktor

2011-08-16

The supramolecular assembly of PS-b-P4VP copolymer micelles induced by selective solvent mixtures was used to manufacture isoporous membranes. Micelle order in solution was confirmed by cryo-scanning electron microscopy in casting solutions, leading to ordered pore morphology. When dioxane, a solvent that interacts poorly with the micelle corona, was added to the solution, polymer-polymer segment contact was preferential, increasing the intermicelle contact. Immersion in water gave rise to asymmetric porous membranes with exceptional pore uniformity and high porosity. The introduction of a small number of carbon nanotubes to the casting solution improved the membrane stability and the reversibility of the gate response in the presence of different pH values.

Molecular Characteristics of Kraft-AQ Pulping Lignin Fractionated by Sequential Organic Solvent Extraction

PubMed Central

Wang, Kun; Xu, Feng; Sun, Runcang

2010-01-01

Kraft-AQ pulping lignin was sequentially fractionated by organic solvent extractions and the molecular properties of each fraction were characterized by chemical degradation, GPC, UV, FT-IR, 13C-NMR and thermal analysis. The average molecular weight and polydispersity of each lignin fraction increased with its hydrogen-bonding capacity (Hildebrand solubility parameter). In addition, the ratio of the non-condensed guaiacyl/syringyl units and the content of β-O-4 linkages increased with the increment of the lignin fractions extracted successively with hexane, diethylether, methylene chloride, methanol, and dioxane. Furthermore, the presence of the condensation reaction products was contributed to the higher thermal stability of the larger molecules. PMID:21152286

Molecular determinants for drug-receptor interactions. Part 2. An ab initio molecular orbital and dipole moment study of the novel nootropic agent piracetam (2-oxopyrrolidin-1-ylacetamide)

NASA Astrophysics Data System (ADS)

Lumbroso, H.; Liégeois, C.; Pappalardo, G. C.; Grassi, A.

From the ab initio molecular energies of the possible conformers and from a classical dipole moment analysis of 2-oxopyrrolidin-l-ylacetamide (μ = 4.02 D in dioxan at 30.0°C), the preferred conformation in solution of this novel nootropic agent has been determined. The exocyclic N-CH 2 bond is rotated in one sense by 90° and the exocyclic CH 2-C bond rotated in the same sense by 120° from the "planar" ( OO)- cis conformation. The structures of the two enantiomers in solution differ from that of the crystalline molecule.

Solubility and dissolution thermodynamics of phthalic anhydride in organic solvents at 283-313 K

NASA Astrophysics Data System (ADS)

Wang, Long; Zhang, Fang; Gao, Xiaoqiang; Luo, Tingliang; Xu, Li; Liu, Guoji

2017-08-01

The solubility of phthalic anhydride was measured at 283-313 K under atmospheric pressure in ethyl acetate, n-propyl acetate, methyl acetate, acetone, 1,4-dioxane, n-hexane, n-butyl acetate, cyclohexane, and dichloromethane. The solubility of phthalic anhydride in all solvents increased with the increasing temperature. The Van't Hoff equation, modified Apelblat equation, λ h equation, and Wilson model were used to correlate the experimental solubility data. The standard dissolution enthalpy, the standard entropy, and the standard Gibbs energy were evaluated based on the Van't Hoff analysis. The experimental data and model parameters would be useful for optimizing of the separation processes involving phthalic anhydride.

Biomineralization of 1,4-dioxane in Pure Culture, Microcosm, and Column Studies Using 13C Labeling

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Azizian, M.; Hyman, M. R.; Semprini, L.

2016-12-01

1,4-dioxane (1,4-D), a probable human carcinogen at low (< 1ppb) concentrations, is a widely occurring groundwater contaminant due to its use as a stabilizer for chlorinated solvents. Aerobic cometabolism, the use of a primary substrate to induce the production of microbial enzymes capable of transforming contaminants into innocuous products, is a promising in-situ treatment strategy for 1,4-D because it has the potential to mineralize trace 1,4-D concentrations to carbon dioxide (CO2). Previous work has confirmed the bacterium Rhodococcus rhodochrous (strain ATCC 21198) will transform 1,4-D when grown on isobutane. In this study, 13C uniformly labeled 1,4-D was used to determine the extent to which strain ATCC 21198 biomineralizes 1,4-D to CO2. Batch experiments have been conducted with pure culture 21198 and in microcosms constructed with aquifer sediments. The rate of resting cell transformation of 1,4-D by ATCC 21198 was over 100 times faster than the rate of CO2 accumulation, indicating the presence of intermediates that were slowly mineralized to CO2 . In microcosms, the use of isobutane as a primary substrate effectively stimulated the native microbial community to transform 1,4-D. Microcosms were also bioaugmented with ATCC 21198. After an initial lag and subsequent additions of isobutane, transformation rates in the native microcosms approached those of the bioaugmented microcosms. Cometabolically active microbes survived several periods of starvation in all microcosms, and nutrient amendment allowed for sustained transformation rates. 13C labeled 1,4-D is currently being used to determine the rates and extents of biomineralization in the microcosms. Column studies are also being conducted to evaluate cometabolism and biominerazation potential of isobutane as a biostimulant and 21198 for bioaugmentation under geochemical and flow conditions more representative of in-situ bioremediation.

Enzymes in Commercial Cellulase Preparations Bind Differently to Dioxane Extracted Lignins

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yarbrough, John M.; Mittal, Ashutosh; Katahira, Rui

Commercial fungal cellulases used in biomass-to-biofuels processes can be grouped into three general classes: native, augmented, and engineered. To evaluate lignin binding affinities of different enzyme activities in various commercial cellulase formulations in order to determine if enzyme losses due to lignin binding can be modulated by using different enzymes of the same activity We used water:dioxane (1:9) to extract lignin from pretreated corn stover. Commercial cellulases were incubated with lignin and the unbound supernatants were evaluated for individual enzyme loss by SDS=PAGE and these were correlated with activity loss using various pNP-sugar substrates. Colorimetric assays for general glycosyl hydrolasemore » activities showed distinct differences in enzyme binding to lignin for each enzyme activity. Native systems demonstrated low binding of endo- and exo-cellulases, high binding of xylanase, and moderate ..beta..-glucosidase binding. Engineered cellulase mixtures exhibited low binding of exo-cellulases, very strong binding of endocellulases and ..beta..- glucosidase, and mixed binding of xylanase activity. The augmented cellulase had low binding of exocellulase, high binding of endocellulase and xylanase, and moderate binding of ..beta..-glucosidase activities. Bound and unbound activities were correlated with general molecular weight ranges of proteins as measured by loss of proteins bands in bound fractions on SDS-PAGE gels. Lignin-bound high molecular weight bands correlated with binding of ..beta..-glucosidase activity. While ..beta..-glucosidases demonstrated high binding in many cases, they have been shown to remain active. Bound low molecular weight bands correlated with xylanase activity binding. Contrary to other literature, exocellulase activity did not show strong lignin binding. The variation in enzyme activity binding between the three classes of cellulases preparations indicate that it is certainly possible to alter the binding of specific glycosyl hydrolase activities. It remains unclear whether loss of endocellulase activity to lignin binding is problematic for biomass conversion.« less

Syntheses, Structures, and Binding Constants of Cyclic Ether and Thioether Adducts of Soluble Cadmium(II) Carboxylates. Intermediates in the Homopolymerization of Oxiranes and Thiiranes and in Carbon Dioxide Coupling Processes.

PubMed

Darensbourg, Donald J.; Niezgoda, Sharon A.; Holtcamp, Matthew W.; Draper, Jennifer D.; Reibenspies, Joseph H.

1997-05-21

A synthetic methodology for the preparation of a large variety of eta(3)-HB(3-Phpz)(3)Cd(acetate) adducts is presented which involves replacement of toluene in the eta(3)-HB(3-Phpz)(3)Cd(acetate) solvate complex by the appropriate cyclic ether or cyclic thioether. In this manner, adducts of THF, dioxane, propylene oxide, cyclohexene oxide, and propylene sulfide were isolated. The solid-state structures of several of these complexes were determined by X-ray crystallography, revealing a six-coordinate complex where the acetate ligand is shown to be fairly symmetrically bonded to the cadmium center. In methylene chloride solution, the cyclic ether or thioether readily dissociates to afford the five-coordinate complex, as demonstrated by (113)Cd NMR. A quantitative assessment of the binding of these base adducts of eta(3)-HB(3-Phpz)(3)Cd(acetate) was determined by measuring the temperature dependence of the equilibrium constants for the five- and six-coordinate derivatives. The presence of one sharp (113)Cd resonance in this equilibrium mixture is indicative of rapid intermolecular exchange between the five- and six-coordinate complexes when compared to the chemical shift differences in these two species ( approximately 6600 Hz at 89 MHz). The order established for ether binding is THF > dioxane > propylene sulfide > cyclohexene oxide >/= propylene oxide, with DeltaH degrees and DeltaS degrees spanning the ranges -27.7 to 24.3 kJ/mol and -89.7 to -94.1 J/(mol K). The epoxide and thioepoxide adducts were shown to serve as models for the initiation step in the copolymerization of epoxides with carbon dioxide catalyzed by metal carboxylates. That is, the carboxylate ligand was shown to ring-open the epoxide or thioepoxide, subsequently affording polyethers or polythioethers with ester end groups. By way of contrast, in the presence of CO(2) and epoxides, this system led to cyclic carbonate production.

Kinetic resolution of drug intermediates catalyzed by lipase B from Candida antarctica immobilized on immobead-350.

PubMed

Pinheiro, Maísa Pessoa; Rios, Nathalia Saraiva; Fonseca, Thiago de S; Bezerra, Francisco de Aquino; Rodríguez-Castellón, Enrique; Fernandez-Lafuente, Roberto; Carlos de Mattos, Marcos; Dos Santos, José C S; Gonçalves, Luciana R B

2018-03-14

Novozyme 435, which is a commercial immobilized lipase B from Candida antarctica (CALB), has been proven to be inadequate for the kinetic resolution of rac-indanyl acetate. As it has been previously described that different immobilization protocols may greatly alter lipase features, in this work, CALB was covalently immobilized on epoxy Immobead-350 (IB-350) and on glyoxyl-agarose to ascertain if better kinetic resolution would result. Afterwards, all CALB biocatalysts were utilized in the hydrolytic resolution of rac-indanyl acetate and rac-(chloromethyl)-2-(o-methoxyphenoxy) ethyl acetate. After optimization of the immobilization protocol on IB-350, its loading capacity was 150 mg protein/g dried support. Furthermore, the CALB-IB-350 thermal and solvent stabilities were higher than that of the soluble enzyme (e.g., by a 14-fold factor at pH 5-70°C and by a 11-fold factor in dioxane 30%-65°C) and that of the glyoxyl-agarose-CALB (e.g., by a 12-fold factor at pH 10-50°C and by a 21-fold factor in dioxane 30%-65°C). The CALB-IB-350 preparation (with 98% immobilization yield and activity versus p-nitrophenyl butyrate of 6.26 ± 0.2 U/g) was used in the hydrolysis of rac-indanyl acetate using a biocatalyst/substrate ratio of 2:1 and a pH value of 7.0 at 30°C for 24 h. The conversion obtained was 48% and the enantiomeric excess of the product (e.e. p ) was 97%. These values were much higher than the ones obtained with Novozyme 435, 13% and 26% of conversion and e.e.p, respectively. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 2018. © 2018 American Institute of Chemical Engineers.

Direct Alkynylation of 3H-Imidazo[4,5-b]pyridines Using gem-Dibromoalkenes as Alkynes Source.

PubMed

Aziz, Jessy; Baladi, Tom; Piguel, Sandrine

2016-05-20

C2 direct alkynylation of 3H-imidazo[4,5-b]pyridine derivatives is explored for the first time. Stable and readily available 1,1-dibromo-1-alkenes, electrophilic alkyne precursors, are used as coupling partners. The simple reaction conditions include an inexpensive copper catalyst (CuBr·SMe2 or Cu(OAc)2), a phosphine ligand (DPEphos) and a base (LiOtBu) in 1,4-dioxane at 120 °C. This C-H alkynylation method revealed to be compatible with a variety of substitutions on both coupling partners: heteroarenes and gem-dibromoalkenes. This protocol allows the straightforward synthesis of various 2-alkynyl-3H-imidazo[4,5-b]pyridines, a valuable scaffold in drug design.

Gas chromatographic-mass spectrometric determination of hydrophilic compounds in environmental water by solid-phase extraction with activated carbon fiber felt.

PubMed

Kawata, K; Ibaraki, T; Tanabe, A; Yagoh, H; Shinoda, A; Suzuki, H; Yasuhara, A

2001-03-09

Simple gas chromatographic-mass spectrometric determination of hydrophilic organic compounds in environmental water was developed. A cartridge containing activated carbon fiber felt was made by way of trial and was evaluated for solid-phase extraction of the compounds in water. The hydrophilic compounds investigated were acrylamide, N,N-dimethylacetamide, N,N-dimethylformamide, 1,4-dioxane, furfural, furfuryl alcohol, N-nitrosodiethylamine and N-nitrosodimethylamine. Overall recoveries were good (80-100%) from groundwater and river water. The relative standard deviations ranged from 4.5 to 16% for the target compounds. The minimum detectable concentrations were 0.02 to 0.03 microg/l. This method was successfully applied to several river water samples.

Unique organogel formation with macroporous materials constructed by the freeze-drying of aqueous cyclodextrin solutions.

PubMed

Marui, Yasuhiro; Kikuzawa, Akira; Kida, Toshiyuki; Akashi, Mitsuru

2010-07-06

Macroporous cyclodextrin materials (MP-alpha-, beta-, and gamma-CDs) were easily fabricated by the freeze-drying of aqueous solutions of alpha-, beta-, and gamma-CDs. These MP-CDs showed the absorption ability toward various organic solvents and oils to give organogels at ambient temperature. The morphological changes of the MP-CD microstructures were observed through the absorption of organic solvents. In particular, the absorption of polar organic solvents with hydrogen-bond forming ability, including 1,4-dioxane and ethanol, by the MP-CDs caused remarkable morphological changes in the microstructures. The absorption of these polar solvents by MP-alpha- and gamma-CDs resulted in the formation of channel-type assemblies of alpha- and gamma-CDs, respectively.

Bis[N-cyclohexyl-1-(2-{1-[(cyclohexyl­amino)carbonyl]cyclohexyl}-3,5-dioxo-1,2-oxazolidin-4-yl)cyclopentanecarbox­amide] monohydrate

PubMed Central

Sheikhhosseini, Enayatollah; Vafadarnejad, Fahime; Habibi, Azizollah

2011-01-01

The reaction of cyclo­hexyl isocyanide and alkyl­idene Meldrum’s acid (systematic name 2,2-dimethyl-1,3-dioxane-4,6-dione) in the presence of cyclo­hexyl ketoxime and dichloro­methane as solvent resulted in the title compound, 2C28H43N3O5·H2O. One methyl­ene group of the cyclo­pentane ring was found to be disordered and was refined with occupancies 0.75:0.25. Intra­molecular N—H⋯O hydrogen bonds occur. The crystal structure is stabilized by inter­molecular N—H⋯O and O—H⋯O hydrogen bonds. PMID:22058907

Theoretical calculations of Electron Paramagnetic Resonance parameters of liquid phase Orotic acid radical

NASA Astrophysics Data System (ADS)

Sarikaya, Ebru Karakaş; Dereli, Ömer

2017-02-01

To obtain liquid phase molecular structure, conformational analysis of Orotic acid was performed and six conformers were determined. For these conformations, eight possible radicals were modelled by using Density Functional Theory computations with respect to molecular structure. Electron Paramagnetic Resonance parameters of these model radicals were calculated and then they were compared with the experimental ones. Geometry optimizations of the molecule and modeled radicals were performed using Becke's three-parameter hybrid-exchange functional combined with the Lee-Yang-Parr correlation functional of Density Functional Theory and 6-311++G(d,p) basis sets in p-dioxane solution. Because Orotic acid can be mutagenic in mammalian somatic cells and it is also mutagenic for bacteria and yeast, it has been studied.

Single-Crystal Structure of a Covalent Organic Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, YB; Su, J; Furukawa, H

2013-11-06

The crystal structure of a new covalent organic framework, termed COF-320, is determined by single-crystal 3D electron diffraction using the rotation electron diffraction (RED) method for data collection. The COF crystals are prepared by an imine condensation of tetra-(4-anilyl)methane and 4,4'-biphenyldialdehyde in 1,4-dioxane at 120 degrees C to produce a highly porous 9-fold interwoven diamond net. COF-320 exhibits permanent porosity with a Langmuir surface area of 2400 m(2)/g and a methane total uptake of 15.0 wt % (176 cm(3)/cm(3)) at 25 degrees C and 80 bar. The successful determination of the structure of COF-320 directly from single-crystal samples is anmore » important advance in the development of COF chemistry.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Builth-Williams, J. D.; Chiari, L.; Jones, D. B., E-mail: darryl.jones@flinders.edu.au, E-mail: michael.brunger@flinders.edu.au

We present experimental and theoretical results for the electron-impact ionization of the highest occupied molecular orbitals of tetrahydropyran and 1,4-dioxane. Using an (e,2e) technique in asymmetric coplanar kinematics, angular distributions of the slow ejected electron, with an energy of 20 eV, are measured when incident electrons at 250 eV ionize the target and scatter through an angle of either −10° or −15°. The data are compared with calculations performed at the molecular 3-body distorted wave level. Fair agreement between the theoretical model and the experimental measurements was observed. The similar structures for these targets provide key insights for assessing themore » limitations of the theoretical calculations. This study in turn facilitates an improved understanding of the dynamics in the ionization process.« less

Novel Cage-Like Hexanuclear Nickel(II) Silsesquioxane. Synthesis, Structure, and Catalytic Activity in Oxidations with Peroxides.

PubMed

Bilyachenko, Alexey N; Yalymov, Alexey I; Shul'pina, Lidia S; Mandelli, Dalmo; Korlyukov, Alexander A; Vologzhanina, Anna V; Es'kova, Marina A; Shubina, Elena S; Levitsky, Mikhail M; Shul'pin, Georgiy B

2016-05-19

New hexanuclear nickel(II) silsesquioxane [(PhSiO1.5)12(NiO)₆(NaCl)] (1) was synthesized as its dioxane-benzonitrile-water complex (PhSiO1,5)12(NiO)₆(NaCl)(C₄H₈O₂)13(PhCN)₂(H₂O)₂ and studied by X-ray and topological analysis. The compound exhibits cylinder-like type of molecular architecture and represents very rare case of polyhedral complexation of metallasilsesquioxane with benzonitrile. Complex 1 exhibited catalytic activity in activation of such small molecules as light alkanes and alcohols. Namely, oxidation of alcohols with tert-butylhydroperoxide and alkanes with meta-chloroperoxybenzoic acid. The oxidation of methylcyclohexane gave rise to the isomeric ketones and unusual distribution of alcohol isomers.

First-principles quantum-mechanical investigations: The role of water in catalytic conversion of furfural on Pd(111)

NASA Astrophysics Data System (ADS)

Xue, Wenhua; Borja, Miguel Gonzalez; Resasco, Daniel E.; Wang, Sanwu

2015-03-01

In the study of catalytic reactions of biomass, furfural conversion over metal catalysts with the presence of water has attracted wide attention. Recent experiments showed that the proportion of alcohol product from catalytic reactions of furfural conversion with palladium in the presence of water is significantly increased, when compared with other solvent including dioxane, decalin, and ethanol. We investigated the microscopic mechanism of the reactions based on first-principles quantum-mechanical calculations. We particularly identified the important role of water and the liquid/solid interface in furfural conversion. Our results provide atomic-scale details for the catalytic reactions. Supported by DOE (DE-SC0004600). This research used the supercomputer resources at NERSC, of XSEDE, at TACC, and at the Tandy Supercomputing Center.

A new approach in the design of organic superconductors

NASA Astrophysics Data System (ADS)

Yamada, J.

2004-04-01

The preparation of charge-transfer (CT) salts of DODHT [(1,4-dioxane-2,3-diyldithio) dihydrotetrathia-fulvalene], BDH-TTP [2,5-bis(1,3-dithiolan-2-ylidene)-1,3,4,6-tetrathiapentalene] and BDA-TTP [2,5-bis(1,3-dithian-2-ylidene)-1,3,4,6-tetrathiapentalene] has been investigated to develop new organic superconductors. The DODHT and BDA-TTP donors give organic superconductors (DODHT){2}BF{4}\\cdot H{2}O and (BDA-TTP){2}X (X = GaCl{4} and FeCl{4}) under applied pressures, whereas (BDH-TTP)Br{0.88} and (BDA-TTF){2}X (X = BF{4}, BF{4}\\cdot H{2}O and ClO{4}) fail to exhibit superconductivity at ambient pressure. Key words. Organic superconductor π -electron donor σ -bond framework loose donor packing motif.

Photodynamic Modification Of Plasma Membrane Function In Erythrocytes Sensitized By Xanthenes: What Determines Potency?

NASA Astrophysics Data System (ADS)

Pooler, John P.

1988-02-01

Several xanthene sensitizers were compared as sensitizers of membrane function in erythrocytes and some of their physico-chemical properties were examined. Eosin derivatives that localize at different membrane sites were equally effective at sensitizing both ion leaks and inactivation of membrane cholinesterase, implying that a diffusible intermediate reacts with membrane targets. Assessments of membrane loading and calculations of diffusion distances for singlet oxygen indicate that amounts of membrane-located sensitizer are quantitatively much greater than amounts in the nearby reaction medium. Potency measurements and assessment of absorption spectra and singlet oxygen production in water-dioxane mixtures lead to the conclusion that differential sorption to membranes, photon capture in low polarity environments and conversion of excited states to singlet oxygen are they key determinants of sensitizing potency.

Study of molecular interactions in binary mixtures of 2-chloro-4'methoxy benzoin with various solvents through ultrasonic speed measurements

NASA Astrophysics Data System (ADS)

Thanuja, B.; Kanakam, C.; Nithya, G.

2013-12-01

Density ( ρ) and ultrasonic velocity ( U), for binary mixtures of 2-chloro-4'-methoxy benzoin with ethanol, chloroform, acetonitrile, benzene and 1,4-dioxane of different compositions have been measured at 298 K and explanation of solute solvent interactions and effect of polarity of the solvent on type of interactions are presented in this paper. From the above data, adiabatic compressibility ( β), intermolecular free length ( L f ) and relative association ( R A ) have been calculated. Other useful parameters such as excess density, excess velocity, excess intermolecular freelength and excess adiabatic compressibility have also been calculated. These parameters have been used to study the nature and extent of intermolecular interactions between component molecules in present binary mixtures.

Measurement of tritium in natural water

NASA Astrophysics Data System (ADS)

Li, Meifen

1985-06-01

A detergent-scintillation liquid mixture applied to measure low specific activity of tritium in natural water was studied. The DYS-1 low level liquid scintillation counter designed and manufactured by our institute was employed. In comparing the Triton X-100 scintillation liquid mixture with the dioxane-based-scintillation liquid, a better formula for Triton X-100 scintillation liquid mixture was determined, the mixture possesses the quality of high water content; high efficiency and low back-ground in measuring tritium in water. Chemiluminescence of the Triton X-100 scintillation liquid mixture can be totally de-excited in short time. It can be employed at ambient temperature 11 28°C. For 20ml sample in quartz vials, counting efficiency is 15% with a background 2.17 cpm, Y=31 TU (t=30 min).

UV Photolysis of Chloramine and Persulfate for 1,4-Dioxane Removal in Reverse-Osmosis Permeate for Potable Water Reuse.

PubMed

Li, Wei; Patton, Samuel; Gleason, Jamie M; Mezyk, Stephen P; Ishida, Kenneth P; Liu, Haizhou

2018-06-05

A sequential combination of membrane treatment and UV-based advanced oxidation processes (UV/AOP) has become the industry standard for potable water reuse. Chloramines are used as membrane antifouling agents and therefore carried over into the UV/AOP. In addition, persulfate (S 2 O 8 2- ) is an emerging oxidant that can be added into a UV/AOP, thus creating radicals generated from both chloramines and persulfate for water treatment. This study investigated the simultaneous photolysis of S 2 O 8 2- and monochloramine (NH 2 Cl) on the removal of 1,4-dioxane (1,4-D) for potable-water reuse. The dual oxidant effects of NH 2 Cl and S 2 O 8 2- on 1,4-D degradation were examined at various levels of oxidant dosage, chloride, and solution pH. Results showed that a NH 2 Cl-to-S 2 O 8 2- molar ratio of 0.1 was optimal, beyond which the scavenging by NH 2 Cl of HO • , SO 4 •- , and Cl 2 •- radicals decreased the 1,4-D degradation rate. At the optimal ratio, the degradation rate of 1,4-D increased linearly with the total oxidant dose up to 6 mM. The combined photolysis of NH 2 Cl and S 2 O 8 2- was sensitive to the solution pH due to a disproportionation of NH 2 Cl at pH lower than 6 into less-photoreactive dichloramine (NHCl 2 ) and radical scavenging by NH 4 + . The presence of chloride transformed HO • and SO 4 •- to Cl 2 •- that is less-reactive with 1,4-D, while the presence of dissolved O 2 promoted gaseous nitrogen production. Results from this study suggest that the presence of chloramines can be beneficial to persulfate photolysis in the removal of 1,4-D; however, the treatment efficiency depends on a careful control of an optimal NH 2 Cl dosage and a minimal chloride residue.

Development of a solid-phase microextraction gas chromatography with microelectron-capture detection method for the determination of 5-bromo-5-nitro-1,3-dioxane in rinse-off cosmetics.

PubMed

Fernandez-Alvarez, Maria; Lamas, J Pablo; Sanchez-Prado, Lucia; Llompart, Maria; Garcia-Jares, Carmen; Lores, Marta

2010-10-22

5-Bromo-5-nitro-1,3-dioxane (bronidox) is a bromine-containing preservative often used in rinse-off cosmetics but also subjected to several restrictions according to the European Cosmetic Products Regulation. Thus, as a part of a quality control procedure, analytical methods for the determination of this compound in different types of cosmetics are required. In the present work, a solvent-free and simple methodology based on solid-phase microextraction (SPME) followed by gas chromatography with microelectron capture detection (GC-μECD) has been developed and validated for the determination of bronidox in cosmetic samples such as shampoos, body cleansers or facial exfoliants. As far as we know, this is the first application of SPME to this preservative. Negative matrix effects due to the complexity of the studied samples were reduced by dilution with ultrapure water. The influence of several factors on the SPME procedure such as fiber coating, extraction temperature, salt addition (NaCl) and sampling mode has been assessed by performing a 2(4)-factorial design. After optimization, the recommended procedure was established as follows: direct solid-phase microextraction (DSPME), using a PDMS/DVB coating, of 10 mL of diluted cosmetic with 20% NaCl, at room temperature, under stirring for 30 min. Using these suggested extraction conditions, linear calibration could be achieved, with limits of detection (LOD) and quantification (LOQ) well below the maximum authorized concentration (0.1%) established by the European legislation. Relative standard deviations (RSD) lower than 10% were obtained for both within a day and among days precision. The method was applied to diverse types of formulations spiked with bronidox at different concentration levels (0.008-0.10%); these samples were quantified by external calibration and satisfactory recoveries (≥ 70%) were obtained in all cases. Finally, the SPME-GC-μECD methodology was applied to the analysis of several cosmetics labeled or not as containing bronidox. The presence of this preservative in some of these samples was confirmed by GC-MS. Copyright © 2010 Elsevier B.V. All rights reserved.

Microcosm Studies to Evaluate Aerobic Cometabolism of Low Concentrations of 1,4-Dioxane by Isobutane-utilizing Microorganisms in the Presence of Chlorinated Solvent Co-contaminants

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Azizian, M.; Hyman, M. R.; Semprini, L.

2015-12-01

Due to its use as a stabilizer for chlorinated solvents, 1,4-dioxane (1,4D), a probable human carcinogen, is a common co-contaminant in solvent spills at industrial and military sites and landfills. Its persistence in large groundwater plumes at low concentrations makes it a relevant candidate for in-situ bioremediation via cometabolism. Microcosm studies are being performed to evaluate the capability of aerobic microorganisms to cometabolize mixtures of 1,4D and chlorinated solvents, such as trichloroethylene (TCE), 1,1,1-trichloroethane (1,1,1TCA), and 1,1-dichloroethene (1,1DCE), with isobutane as the primary substrate. Microcosms were constructed using aquifer solids from Fort Carson, Colorado, a site contaminated with 1,4D and TCE, to assess the isobutane uptake and transformation of 1,4D and chlorinated solvents by microorganisms native to the site. Additional microcosms were augmented with Rhodococcus rhodochrous, a bacterium shown to cometabolize 1,4D and chlorinated solvents. Results indicate that native microcosms cometabolized 1,4D upon stimulation with isobutane after a lag period of about 15 days. TCE was also transformed, but at significantly slower rates. The presence of 1,4D and TCE at 500 and 300 ppb, respectively, did not inhibit the growth of native microorganisms on isobutane, with isobutane uptake and 1,4D transformation occurring simultaneously. Bioaugmented microcosms transformed 1,4D immediately after inoculation with R. rhodochrous. Tests in bioaugmented microorganisms indicated that the presence of TCE at low concentrations inhibits but does not block the transformation of 1,4D. Results from the microcosms will be used to design field tests to be performed at Fort Carson. Additional microcosm studies will compare the stimulation of native and bioaugmented microcosms and the transformation of mixtures of 1,4D, 1,1,1TCA and 1,1DCE. Molecular methods will analyze the monoxygenase enzymes expressed in the native and bioaugmented microcosms.

Kinetic Studies of the Cometabolism of 1,4-DIOXANE and Chlorinated Aliphatic Hydrocarbon Mixtures by Rhodococcus Rhodochrous Grown on Isobutane

NASA Astrophysics Data System (ADS)

Rolston, H. M.; Semprini, L.; Thankitkul, S.; Azizian, M.; Hyman, M. R.

2016-12-01

1,4-dioxane (1,4-D) is a frequently observed groundwater contaminant due to its use as a stabilizer in commercial solvent formulations. In situ bioremediation could potentially provide a large cost savings for treatment of mixtures of chlorinated aliphatic hydrocarbons (CAHs) that include 1,4-D. Aerobic cometabolism is a particularly attractive option, as microorganisms can be stimulated in situ using specific primary substrates. Results will be presented that show the model isobutane-metabolizing bacteria, Rhodococcus rhodochrous (ATCC 21198), has the ability to transform 14-D at high rates and transformation capacities to concentrations below the drinking water screening level of 0.67 µg L-1. Resting cell transformation tests showed 1,4-D and a broad range of CAHs can be cometabolized by ATCC 21198. The maximum transformation rate (kmax) and the half-substrate coefficient (Ks) were determined for isobutane (the growth substrate), 1,4-D, 1,1,1-trichloroethane (1,1,1-TCA), 1,1,2-trichloroethane (1,1,2-TCA), 1,1-dichloroethane (1,1-DCA); 1,2-dichloroethane ((1,2-DCA) and 1,1-dichloroethene (1,1-DCE). Of the CAHs tested, 1,1-DCA had the highest kmax, approximately 25% of that for isobutane utilization, while 1,1,1-TCA had the lowest kmax, approximately 2% of isobutane's. 1,4-D was rapidly transformed and had a kmax 25% of that of isobutane. ATCC 21198 effectively transformed mixtures of 1,4-D, 1,1-DCE, 1,2-DCA and 1,1,1-TCA, both in the presence and absence isobutane. Model simulations were performed for the simultaneous cometabolism of 1,4-D and CAH mixtures by ATCC 21198, that included inhibition among the contaminants and isobutane , and terms for a limited transformation capacity. A good match to experimental observations was obtaining using the independently measured rate parameters. Results of model simulations will also be presented using a reactive transport model to evaluate conditions of in situ bioremediation using strain ATCC 21198.

Assessment of potential aluminum chelators in an octanol/aqueous system and in the aluminum-loaded rabbit.

PubMed

Yokel, R A; Kostenbauder, H B

1987-11-01

Aluminum (Al) solubilization from Al borate and its distribution in an octanol/aqueous system (Do/w) were determined in the absence and presence of 12 potential Al chelators. Citrate, N,N'-bis-(2-hydroxybenzyl)ethylenediamine- N,N'-diacetic acid (HBED), cyclohexane-1,2-diaminotetraacetic acid (CDTA), diethylenetriaminepentaacetic acid (DTPA), nitrilotriacetic acid (NTA), desferrioxamine, and ethylenediamine-N,N'-bis(2-dihydroxyphenylacetic acid) (EDDHA) were 55 to over 100% efficient in solubilizing equimolar amounts of Al. Tetracycline, EDTA, and 2,3-dihydroxybenzoic acid (DHBA) were less than 20% efficient. 1,4-Dioxane and fluoride were ineffective. The Do/w of Al averaged 0.005. The Do/w of the Al.chelator complex was generally less than that of Al, except for HBED and tetracycline (0.04 and 0.96, respectively). The Do/w of DHBA, desferrioxamine, EDDHA, and HBED were not influenced by Al, but tetracycline became more lipophilic. These compounds were tested for their ability to increase urinary Al excretion in Al-loaded rabbits. Chelators were given po weekly beginning 2 weeks after Al loading. Urine was obtained hourly from 3 hr prior to 6 hr after chelator administration and analyzed for Al. Fluoride and tetracycline (450 and 4500 mumol/kg) and citrate, NTA, EDTA, CDTA, DTPA, DHBA, HBED, and 1,4-dioxane (150 and 1500 mumol/kg) were ineffective. Following HBED administration, some of the Al-loaded rabbits died, presumably due to redistribution of Al within the rabbit. Following DTPA administration, some of the Al-loaded rabbits died, presumably due to DTPA. Oral EDDHA (1500 mumol/kg) significantly increased urinary Al excretion. EDDHA and desferrioxamine (150 mumol/kg) were administered by po, sc, and iv routes and were found to have comparable potency. The in vitro results may explain some of the in vivo findings. The in vitro methods may be useful to screen out compounds with no chelation potential. EDDHA-like compounds may have potential as alternatives to desferrioxamine in the prevention or treatment of Al accumulation and Al-induced toxicity.

Development of autoclavable polyimides. [fabrication procedures of high temperature resistant/fiber composite

NASA Technical Reports Server (NTRS)

Orell, M. K.; Sheppard, C. H.; Vaughan, R. W.; Jones, R. J.

1974-01-01

A poly(Diels-Alder) (PDA) resin approach was investigated as a means to achieve autoclavability of high temperature resistant resin/fiber composites under mild fabrication procedures. Low void content Type A-S graphite reinforced composites were autoclave fabricated from a PDA resin/fiber prepared from an acetone:methanol:dioxane varnish. Autoclave conditions were 477K (400F) and 0.7 MN/sq m (100 psi) for up to two hours duration. After postcure at temperatures up to 589K (600F), the composites demonstrated high initial mechanical properties at temperatures up to 561K (550F). The results from isothermal aging studies in air for 1000 hours indicated potential for long-term ( 1000 hours) use at 533K (500F) and shorter-term (up to 1000 hours) at 561K (550F).

Coordination properties of tridentate (N,O,O) heterocyclic alcohol (PDC) with Cu(II). Mixed ligand complex formation reactions of Cu(II) with PDC and some bio-relevant ligands.

PubMed

El-Sherif, Ahmed A; Shoukry, Mohamed M

2007-03-01

The formation equilibria of copper(II) complexes and the ternary complexes Cu(PDC)L (PDC=2,6-bis-(hydroxymethyl)-pyridine, HL=amino acid, amides or DNA constituents) have been investigated. Ternary complexes are formed by a simultaneous mechanism. The results showed the formation of Cu(PDC)L, Cu(PDC, H(-1))(L) and Cu(PDC, H(-2))(L) complexes. The concentration distribution of the complexes in solution is evaluated as a function of pH. The effect of dioxane as a solvent on the protonation constant of PDC and the formation constants of Cu(II) complexes are discussed. The thermodynamic parameters DeltaH degrees and DeltaS degrees calculated from the temperature dependence of the equilibrium constants are investigated.

Solvent-induced chirality control in the enantioseparation of 1-phenylethylamine via diastereomeric salt formation.

PubMed

Kodama, Koichi; Kimura, Yuria; Shitara, Hiroaki; Yasutake, Mikio; Sakurai, Rumiko; Hirose, Takuji

2011-04-01

Solvent-induced chirality control in the enantioseparation of 1-phenylethylamine 1 by N-(p-toluenesulfonyl)-(S)-phenylalanine 2 via diastereomeric salt formation was studied. (S)-1·(S)-2 was preferentially crystallized as a less-soluble salt from aqueous alcohol, while (R)-1·(S)-2 salt was mainly obtained by addition of solvents with a six-membered ring such as dioxane, cyclohexane, tetrahydropyran, and cyclohexene to 2-propanol. Further investigations were carried out from the viewpoints of molecular structures, optical rotation measurement, and X-ray crystallographic analyses. Crystallographic analyses have revealed that incorporation of the six-membered ring solvent molecule in (R)-1·(S)-2 without hydrogen bonds changed the molecular conformation of (S)-2 to stabilize the salt, which changed the selectivity of 1 in the enantioseparation. Copyright © 2010 Wiley-Liss, Inc.

Homogeneous catalyst formulations for methanol production

DOEpatents

Mahajan, Devinder; Sapienza, Richard S.; Slegeir, William A.; O'Hare, Thomas E.

1991-02-12

There is disclosed synthesis of CH.sub.3 OH from carbon monoxide and hydrogen using an extremely active homogeneous catalyst for methanol synthesis directly from synthesis gas. The catalyst operates preferably between 100.degree.-150.degree. C. and preferably at 100-150 psia synthesis gas to produce methanol. Use can be made of syngas mixtures which contain considerable quantities of other gases, such as nitrogen, methane or excess hydrogen. The catalyst is composed of two components: (a) a transition metal carbonyl complex and (b) an alkoxide component. In the simplest formulation, component (a) is a complex of nickel tetracarbonyl and component (b) is methoxide (CH.sub.3 O.sup.-), both being dissolved in a methanol solvent system. The presence of a co-solvent such as p-dioxane, THF, polyalcohols, ethers, hydrocarbons, and crown ethers accelerates the methanol synthesis reaction.

Homogeneous catalyst formulations for methanol production

DOEpatents

Mahajan, Devinder; Sapienza, Richard S.; Slegeir, William A.; O'Hare, Thomas E.

1990-01-01

There is disclosed synthesis of CH.sub.3 OH from carbon monoxide and hydrogen using an extremely active homogeneous catalyst for methanol synthesis directly from synthesis gas. The catalyst operates preferably between 100.degree.-150.degree. C. and preferably at 100-150 psia synthesis gas to produce methanol. Use can be made of syngas mixtures which contain considerable quantities of other gases, such as nitrogen, methane or excess hydrogen. The catalyst is composed of two components: (a) a transition metal carbonyl complex and (b) an alkoxide component. In the simplest formulation, component (a) is a complex of nickel tetracarbonyl and component (b) is methoxide (CH.sub.3 O.sup.13 ), both being dissolved in a methanol solvent system. The presence of a co-solvent such as p-dioxane, THF, polyalcohols, ethers, hydrocarbons, and crown ethers accelerates the methanol synthesis reaction.

Furfural production from Eucalyptus wood using an Acidic Ionic Liquid.

PubMed

Peleteiro, Susana; Santos, Valentín; Garrote, Gil; Parajó, Juan Carlos

2016-08-01

Eucalyptus globulus wood samples were treated with hot, compressed water to separate hemicelluloses (as soluble saccharides) from a solid phase mainly made up of cellulose and lignin. The liquid phase was dehydrated, and the resulting solids (containing pentoses as well as poly- and oligo- saccharides made up of pentoses) were dissolved and reacted in media containing an Acidic Ionic Liquid (1-butyl-3-methylimidazolium hydrogen sulfate) and a co-solvent (dioxane). The effects of the reaction time on the product distribution were studied at temperatures in the range 120-170°C for reaction times up to 8h, and operational conditions leading to 59.1% conversion of the potential substrates (including pentoses and pentose structural units in oligo- and poly- saccharides) into furfural were identified. Copyright © 2016 Elsevier Ltd. All rights reserved.

On the Plausibility of Pseudosugar Formation in Cometary Ices and Oxygen-rich Tholins

NASA Astrophysics Data System (ADS)

Lavado, Nieves; Ávalos, Martín; Babiano, Reyes; Cintas, Pedro; Light, Mark E.; Jiménez, José Luis; Palacios, Juan C.

2016-03-01

We revisit herein the formation and structure of dihydroxy dioxanes, which can be obtained from prebiotically available precursors and can be regarded as primeval sugar surrogates. Previous studies dealing with the heterogeneous composition of interstellar bodies point to the existence of significant amounts of small polyalcohols along with oxygen-containing oligomers. Even though such derivatives did not give rise to nucleosides and oligonucleotides, nor they were incorporated into subsequent metabolic routes, molecular chimeras based on sugar-like species could be opportunistic scaffolds in pre-evolutionary scenarios. We could figure out that pseudosugars, assembled by hemiacetalic bonds from available precursors in both interstellar and terrestrial scenarios, were presumably more abundant than thought. Moreover, these species share some key features with naturally-occurring sugar rings, such as anomeric preferences, coordinating ability, and the prevalent occurrence of racemic compounds.

Synthesis, crystal structure, vibrational spectra and theoretical calculations of quantum chemistry of a potential antimicrobial Meldrum's acid derivative

NASA Astrophysics Data System (ADS)

Campelo, M. J. M.; Freire, P. T. C.; Mendes Filho, J.; de Toledo, T. A.; Teixeira, A. M. R.; da Silva, L. E.; Bento, R. R. F.; Faria, J. L. B.; Pizani, P. S.; Gusmão, G. O. M.; Coutinho, H. D. M.; Oliveira, M. T. A.

2017-10-01

A new derivative of Meldrum's acid 5-((5-chloropyridin-2-ylamino)methylene)-2,2-dimethyl-1,3-dioxane-4,6-dione (CYMM) of molecular formula C12H11ClN2O4 was synthesized and structurally characterized using single crystal X-ray diffraction technique. The vibrational properties of the crystal were studied by Fourier Transform infrared (FT-IR), Fourier Transform Raman (FT-Raman) techniques and theoretical calculations of quantum chemistry using Density functional theory (DFT) and Density functional perturbation theory (DFPT). A comparison with experimental spectra allowed the assignment of all the normal modes. The descriptions of the normal modes were carried by means of potential energy distribution (PED). Additionally, analysis of the antimicrobial activity and antibiotic resistance modulatory activity was carried out to evaluate the antibacterial potential of the CYMM.

Ultrasonic studies of intermolecular interactions in binary mixtures of 4-methoxy benzoin with various solvents: Excess molar functions of ultrasonic parameters at different concentrations and in different solvents.

PubMed

Thanuja, B; Nithya, G; Kanagam, Charles C

2012-11-01

Density (ρ), ultrasonic velocity (U), for the binary mixtures of 4-methoxy benzoin (4MB) with ethanol, chloroform, acetonitrile, benzene, and di-oxane were measured at 298K. The solute-solvent interactions and the effect of the polarity of the solvent on the type of intermolecular interactions are discussed here. From the above data, adiabatic compressibility (β), intermolecular free length (L(f)), acoustic impedance (Z), apparent molar volume (Ø), relative association (RA) have been calculated. Other useful parameters such as excess density, excess velocity and excess adiabatic compressibility have also been calculated. These parameters were used to study the nature and extent of intermolecular interactions between component molecules in the binary mixtures. Copyright © 2012 Elsevier B.V. All rights reserved.

New phenanthrene and 9, 10-dihydrophenanthrene derivatives from the stems of Dendrobium officinale with their cytotoxic activities.

PubMed

Zhao, Gui-Yun; Deng, Bo-Wen; Zhang, Chong-Yu; Cui, Yi-Da; Bi, Jia-Yi; Zhang, Guo-Gang

2018-01-01

Two new phenanthrene and 9, 10-dihydrophenanthrene derivatives (1-2) with six known congeners (3-8) were isolated from the extraction of stems of Dendrobium officinale. Compounds 1 and 2 were based on carbon skeleton in which phenanthrene and 9, 10-dihydrophenanthrene moiety were linked with a phenylpropane unit through a dioxane bridge, respectively. Their structures were determined by comprehensive NMR spectroscopic data, the absolute configuration of new compounds were determined by comparing their experimental and calculated ECD for the first time. All the compounds were investigated contains two cancer cell lines (HI-60, THP-1). All the isolates showed cytotoxicity, especially compound 4 showed markedly cytotoxic activities against HI-60 and THP-1 cell lines with IC 50 values of 11.96 and 8.92 μM.

Bonded exciplex formation: electronic and stereoelectronic effects.

PubMed

Wang, Yingsheng; Haze, Olesya; Dinnocenzo, Joseph P; Farid, Samir; Farid, Ramy S; Gould, Ian R

2008-12-18

As recently proposed, the singlet-excited states of several cyanoaromatics react with pyridine via bonded-exciplex formation, a novel concept in photochemical charge transfer reactions. Presented here are electronic and steric effects on the quenching rate constants, which provide valuable support for the model. Additionally, excited-state quenching in poly(vinylpyridine) is strongly inhibited both relative to that in neat pyridine and also to conventional exciplex formation in polymers, consistent with a restrictive orientational requirement for the formation of bonded exciplexes. Examples of competing reactions to form both conventional and bonded exciplexes are presented, which illustrate the delicate balance between these two processes when their reaction energetics are similar. Experimental and computational evidence is provided for the formation of a bonded exciplex in the reaction of the singlet excited state of 2,6,9,10-tetracyanoanthracene (TCA) with an oxygen-substituted donor, dioxane, thus expanding the scope of bonded exciplexes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riande, E.; Guzman, J.; Roman, J.S.

The dipole moments of poly (thiodiethylene glycol terephthalate) chains were determined as a function of temperature by means of dielectric constant measurements in dioxane. The experimental results were found to be in fair agreement with theoretical results based on a rotational isomeric state model in which the required conformational energies were obtained from previous configurational analysis on poly(ethylene terephthalate), poly(diethylene glycol terephthalate) and poly(thiodiethylene glycol). Since poly(thiodiethylene glycol terephthalate) can be considered an alternating copolymer of ethylene terephthalate and thioethylene units, its configuration-dependent properties were compared with those of poly(ethylene terephthalate) and poly(ethylene sulfide). It was found the flexibility ofmore » the copolymer, as expressed by the partition function, intermediate to that of its parent homopolymers. The theoretical results also indicate that the dimensions of poly(thiodiethylene glycol) are similar to those of poly(ethylene terephthalate) while its dipole moment ratio resembles that of poly(ethylene sulfide).« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crandall, M.S.; Wilcox, T.G.

An evaluation was made of working conditions at the Graphic Packaging Corporation, Paoli, Pennsylvania. Particular attention was given to workers making microwave popcorn bags who reported swelling around the eyes and dermatitis. One employee also reported an asthma attack while working on the bags. Special water-based epoxy adhesives were used for these bags as the product must withstand heating in a microwave oven. Environmental and personal breathing-zone air samples were taken and medical questionnaires were filled out. Use of the adhesive was discontinued in May of 1987 and the symptoms have disappeared. Chemical analysis of the adhesive indicated the presencemore » of several chemicals that are potential irritants or allergic sensitizers both to skin and the respiratory tract. These irritants included formaldehyde, acetaldehyde, benzoic acid, 1,1,1-trichloroethane, p-dioxane, and ethyl acetate. Samples taken before the switchover to another adhesive was made did not indicate a hazardous level of any of these substances to be present.« less

Effects of hydroxylated benzaldehyde derivatives on radiation-induced reactions involving various organic radicals

NASA Astrophysics Data System (ADS)

Ksendzova, G. A.; Samovich, S. N.; Sorokin, V. L.; Shadyro, O. I.

2018-05-01

In the present paper, the effects of hydroxylated benzaldehyde derivatives and gossypol - the known natural occurring compound - on formation of decomposition products resulting from radiolysis of ethanol and hexane in deaerated and oxygenated solutions were studied. The obtained data enabled the authors to make conclusions about the effects produced by the structure of the compounds under study on their reactivity towards oxygen- and carbon-centered radicals. It has been found that 2,3-dihydroxybenzaldehyde, 4,6-di-tert-butyl-2,3-dihydroxybenzaldehyde and 4,6-di-tert-butyl-3-(1,3-dioxane-2-yl)-1,2-dihydroxybenzene are not inferior in efficiency to butylated hydroxytoluene - the industrial antioxidant - as regards suppression of the radiation-induced oxidation processes occurring in hexane. The derivatives of hydroxylated benzaldehydes were shown to have a significant influence on radiation-induced reactions involving α-hydroxyalkyl radicals.

Crystal structure of 5''-(4-chloro-benzyl-idene)-4'-(4-chloro-phen-yl)-1'-methyltri-spiro[acenapthylene-1,2'-pyrrolidine-3',1''-cyclo-hexane-3'',2'''-[1,3]dioxane]-2(1H),6''-dione.

PubMed

Chandralekha, Kuppan; Gavaskar, Deivasigamani; Sureshbabu, Adukamparai Rajukrishnan; Lakshmi, Srinivasakannan

2015-11-01

In the title compound, C36H29Cl2NO4, two spiro links connect the methyl-substituted pyrrolidine ring to the ace-naphthyl-ene and cyclo-hexa-none rings. The cyclo-hexa-none ring is further connected to the dioxalane ring by a third spiro junction. The five-membered ring of the ace-naphthylen-1-one ring system adopts a flattened envelope conformation, with the ketonic C atom as the flap, whereas the dioxalane and pyrrolidine rings each have a twist conformation. The cyclo-hexenone ring assumes a boat conformation. An intra-molecular C-H⋯O hydrogen-bond inter-action is present. In the crystal, mol-ecules are linked by non-classical C-H⋯O hydrogen bonds, forming chains extending parallel to the a axis.

The interaction of heme with plakortin and a synthetic endoperoxide analogue: new insights into the heme-activated antimalarial mechanism

NASA Astrophysics Data System (ADS)

Persico, Marco; Fattorusso, Roberto; Taglialatela-Scafati, Orazio; Chianese, Giuseppina; de Paola, Ivan; Zaccaro, Laura; Rondinelli, Francesca; Lombardo, Marco; Quintavalla, Arianna; Trombini, Claudio; Fattorusso, Ernesto; Fattorusso, Caterina; Farina, Biancamaria

2017-04-01

In the present work we performed a combined experimental and computational study on the interaction of the natural antimalarial endoperoxide plakortin and its synthetic analogue 4a with heme. Obtained results indicate that the studied compounds produce reactive carbon radical species after being reductively activated by heme. In particular, similarly to artemisinin, the formation of radicals prone to inter-molecular reactions should represent the key event responsible for Plasmodium death. To our knowledge this is the first experimental investigation on the reductive activation of simple antimalarial endoperoxides (1,2-dioxanes) by heme and results were compared to the ones previously obtained from the reaction with FeCl2. The obtained experimental data and the calculated molecular interaction models represent crucial tools for the rational optimization of our promising class of low-cost synthetic antimalarial endoperoxides.

Imidazolium-Based Ionic Liquids as Efficient Reagents for the C-O Bond Cleavage of Lignin.

PubMed

Thierry, Marina; Majira, Amel; Pégot, Bruce; Cezard, Laurent; Bourdreux, Flavien; Clément, Gilles; Perreau, François; Boutet-Mercey, Stéphanie; Diter, Patrick; Vo-Thanh, Giang; Lapierre, Catherine; Ducrot, Paul-Henri; Magnier, Emmanuel; Baumberger, Stéphanie; Cottyn, Betty

2018-01-23

The demethylation of lignin in ionic liquids (ILs) was investigated by using pure lignin model monomers and dimers together with dioxane-isolated lignins from poplar, miscanthus, and maize. Different methylimidazolium ILs were compared and the samples were treated with two different heating processes: microwave irradiation and conventional heating in a sealed tube. The conversion yield and influence of the treatment on the lignin structure were assessed by 31 P NMR spectroscopy, size-exclusion chromatography, and thioacidolysis. The acidic methylimidazolium IL [HMIM]Br was shown to be an effective combination of solvent and reagent for the demethylation and depolymerization of lignin. The relatively mild reaction conditions, the clean work-up, and the ability to reuse the IL makes the described procedure an attractive and new green method for the conversion of lignin to produce phenol-rich lignin oligomers. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of five- and six-membered cyclic organic peroxides: Key transformations into peroxide ring-retaining products

PubMed Central

Borisov, Dmitry A; Vil’, Vera A; Dembitsky, Valery M

2014-01-01

Summary The present review describes the current status of synthetic five and six-membered cyclic peroxides such as 1,2-dioxolanes, 1,2,4-trioxolanes (ozonides), 1,2-dioxanes, 1,2-dioxenes, 1,2,4-trioxanes, and 1,2,4,5-tetraoxanes. The literature from 2000 onwards is surveyed to provide an update on synthesis of cyclic peroxides. The indicated period of time is, on the whole, characterized by the development of new efficient and scale-up methods for the preparation of these cyclic compounds. It was shown that cyclic peroxides remain unchanged throughout the course of a wide range of fundamental organic reactions. Due to these properties, the molecular structures can be greatly modified to give peroxide ring-retaining products. The chemistry of cyclic peroxides has attracted considerable attention, because these compounds are used in medicine for the design of antimalarial, antihelminthic, and antitumor agents. PMID:24454562

Crystallisation of alpha-crustacyanin, the lobster carapace astaxanthin-protein: results from EURECA

NASA Astrophysics Data System (ADS)

Zagalsky, P. F.; Wright, C. E.; Parsons, M.

1995-08-01

Crystallisation of alpha-crustacyanin, the lobster carapace astaxanthin-protein was attempted under microgravity conditions in EURECA satellite using liquid-liquid diffusion with polyethyleneglycol (PEG) as precipitant; in a second reaction chamber phenol and dioxan were used as additives to prevent composite crystal growth. Crystals of alpha-crustacyanin grown under microgravity from PEG were larger than those grown terrestrially in the same apparatus under otherwise identical conditions. On retrieval, the crystals from PEG were shown to be composite and gave a powder diffraction pattern. The second reaction chamber showed leakage on retrieval and had also been subjected to rapid temperature variation during flight. Crystal fragments were nevertheless recovered but showed a powder diffraction pattern. It is concluded, certainly for liquid-liquid diffusion using PEG alone, that, for crustacyanin, although microgravity conditions resulted in an increase in dimensions of crystals, a measurable improvement in molecular ordering was not achieved.

Study of intermolecular interactions in binary mixtures of 2'-chloro-4-methoxy-3-nitro benzil in various solvents and at different concentrations by the measurement of acoustic properties.

PubMed

Nithya, G; Thanuja, B; Kanagam, Charles C

2013-01-01

Density (ρ), ultrasonic velocity (u), adiabatic compressibility (β), apparent molar volume (Ø), acoustic impedance (Z), intermolecular free length (L(f)), relative association (RA) of binary mixtures of 2'-chloro-4-methoxy-3-nitro benzil (abbreviated as 2CBe) in ethanol, acetonitrile, chloroform, dioxane and benzene were measured at different concentrations at 298 K. Several useful parameters such as excess density, excess ultrasonic velocity, excess adiabatic compressibility, excess apparent molar volume, excess acoustic impedance and excess intermolecular free length have been calculated. These parameters are used to explain the nature of intermolecular interactions taking place in the binary mixture. The above study is useful in understanding the solute--solvent interactions occurring in different concentrations at room temperature. Copyright © 2012 Elsevier B.V. All rights reserved.

Charge-transfer complexes of phenylephrine with nitrobenzene derivatives

NASA Astrophysics Data System (ADS)

El-Mossalamy, E. H.

2004-04-01

The molecular charge-transfer complexes of phenylephrine with picric acid and m-dinitrobenzene have been studied and investigated by IR, 1H NMR electronic spectra in organic solvents and buffer solutions, respectively. Simple and selective methods are proposed for the determination of phenylephrine hydrochloride in bulk form and in tablets. The two methods are based on the formation of charge-transfer complexes between drug base as a n-donor (D) and picric acid, m-dinitrobenzene as π-acceptor (A). The products exhibit absorption maxima at 497 and 560 nm in acetonitrile for picric acid and m-dinitrobenzene, respectively. The coloured product exhibits an absorption maximum at 650 nm in dioxane. The sensitive kinetic methods for the determination phynylephrine hydrochloride are described. The method is based upon a kinetic investigation of the oxidation reaction of the drug with alkaline potassium permanganate at room temperature for a fixed time at 20 min.

Solvent effect on the self-assembly of salt solvates of an antihypertensive drug azilsartan and 2-methylimidazole

NASA Astrophysics Data System (ADS)

Zhang, Xian-Rui; Zhang, Lei

2017-06-01

Three salt solvates of azilsartan (AZ) with 2-methylimidazole (2MI) (namely AZ-2MI-H2O, AZ-2MI-ACE and AZ-2MI-THF) and one azilsartan solvate (AZ-DIO, ACE = acetone, THF = tetrahydrofuran, and DIO = 1,4-dioxane) were manufactured by solvent-controlled self-assembly in aqueous-organic solutions. The experimental result of AZ-DIO shows that AZ is high affinity to DIO molecule, which has a unique ability to prevent salt formation between AZ and 2MI. Thermal studies of three salt solvates exhibit poor thermodynamic stability in environmental conditions. Solubility experiments show that AZ-2MI-ACE and AZ-2MI-THF are unstable and convert to AZ-2MI-H2O in aqueous solution, and that AZ-2MI-H2O exhibits increased solubility and retention stability in an aqueous medium compared with the commercial AZ-A crystalline form.

Challenges in preparing, preserving and detecting para-water in bulk: overcoming proton exchange and other hurdles.

PubMed

Mammoli, Daniele; Salvi, Nicola; Milani, Jonas; Buratto, Roberto; Bornet, Aurélien; Sehgal, Akansha Ashvani; Canet, Estel; Pelupessy, Philippe; Carnevale, Diego; Jannin, Sami; Bodenhausen, Geoffrey

2015-10-28

Para-water is an analogue of para-hydrogen, where the two proton spins are in a quantum state that is antisymmetric under permutation, also known as singlet state. The populations of the nuclear spin states in para-water are believed to have long lifetimes just like other Long-Lived States (LLSs). This hypothesis can be verified by measuring the relaxation of an excess or a deficiency of para-water, also known as a "Triplet-Singlet Imbalance" (TSI), i.e., a difference between the average population of the three triplet states T (that are symmetric under permutation) and the population of the singlet state S. In analogy with our recent findings on ethanol and fumarate, we propose to adapt the procedure for Dissolution Dynamic Nuclear Polarization (D-DNP) to prepare such a TSI in frozen water at very low temperatures in the vicinity of 1.2 K. After rapid heating and dissolution using an aprotic solvent, the TSI should be largely preserved. To assess this hypothesis, we studied the lifetime of water as a molecular entity when diluted in various solvents. In neat liquid H2O, proton exchange rates have been characterized by spin-echo experiments on oxygen-17 in natural abundance, with and without proton decoupling. One-dimensional exchange spectroscopy (EXSY) has been used to study proton exchange rates in H2O, HDO and D2O mixtures diluted in various aprotic solvents. In the case of 50 mM H2O in dioxane-d8, the proton exchange lifetime is about 20 s. After dissolving, one can observe this TSI by monitoring intensities in oxygen-17 spectra of H2O (if necessary using isotopically enriched samples) where the AX2 system comprising a "spy" oxygen A and two protons X2 gives rise to binomial multiplets only if the TSI vanishes. Alternatively, fast chemical addition to a suitable substrate (such as an activated aldehyde or ketone) can provide AX2 systems where a carbon-13 acts as a spy nucleus. Proton signals that relax to equilibrium with two distinct time constants can be considered as a hallmark of a TSI. We optimized several experimental procedures designed to preserve and reveal dilute para-water in bulk.

Structural characterization of lignin from grape stalks (Vitis vinifera L.).

PubMed

Prozil, Sónia O; Evtuguin, Dmitry V; Silva, Artur M S; Lopes, Luísa P C

2014-06-18

The chemical structure of lignin from grape stalks, an abundant waste of winemaking, has been studied. The dioxane lignin was isolated from extractive- and protein-free grape stalks (Vitis vinifera L.) by modified acidolytic procedure and submitted to a structural analysis by wet chemistry (nitrobenzene and permanganate oxidation (PO)) and spectroscopic techniques. The results obtained suggest that grape stalk lignin is an HGS type with molar proportions of p-hydroxyphenyl (H), guaiacyl (G) and syringyl (S) units of 3:71:26. Structural analysis by (1)H and (13)C NMR spectroscopy and PO indicates the predominance of β-O-4' structures (39% mol) in grape stalk lignin together with moderate amounts of β-5', β-β, β-1', 5-5', and 4-O-5' structures. NMR studies also revealed that grape lignin should be structurally associated with tannins. The condensation degree of grape stalks lignin is higher than that of conventional wood lignins and lignins from other agricultural residues.

Crystal structure of 5''-benzyl-idene-1'-methyl-4'-phenyl-tri-spiro-[ace-naphthyl-ene-1,2'-pyrrolidine-3',1''-cyclo-hexane-3'',2'''-[1,3]dioxane]-2,6''-dione.

PubMed

Chandralekha, Kuppan; Gavaskar, Deivasigamani; Sureshbabu, Adukamparai Rajukrishnan; Lakshmi, Srinivasakannan

2016-03-01

In the title compound, C36H31NO4, two spiro links connect the methyl-substituted pyrrolidine ring to the ace-naphthyl-ene and cyclo-hexa-none rings. The cyclo-hexa-none ring is further connected to the dioxalane ring by a third spiro junction. The five-membered ring of the ace-naphthylen-1-one ring system adopts a flattened envelope conformation with the ketonic C atom as flap, whereas the dioxalane and pyrrolidine rings each have a twist conformation. The cyclo-hexa-none ring assumes a boat conformation. Three intra-molecular C-H⋯O hydrogen bonds involving both ketonic O atoms as acceptors are present. In the crystal, C-H⋯O hydrogen bonds connect centrosymmetrically related mol-ecule into chains parallel to the b axis, forming rings of R 2 (2)(10)and R 2 (2)(8) graph-set motifs.

Synthesis of 3 alpha, 5 alpha-tetrahydroaldosterone.

PubMed

Harnik, M; Kashman, Y; Morris, D J

1984-06-01

3 alpha, 5 alpha-Tetrahydroaldosterone (12a), a metabolite of aldosterone, has been synthesized from the lactone 2a or, preferably 11 beta, 21-dihydroxy-5-pregnene-3,20-dione-18-oic acid 3,20-di-(ethylene glycol)-ketal (18----11) lactone 21-acetate (6b), via 11 beta, 21-dihydroxy-5 alpha-pregnane-3,20-dione-18-oic acid 3,20-di-(ethylene glycol) ketal (18----11) lactone 21-acetate (4b). Selective hydrolysis of the latter at C-3 furnished the monoketal 5 which, on reduction with potassium tri-sec-butylborohydride, yielded predominantly 3 alpha, 11 beta, 21-trihydroxy-5 alpha-pregnan-20-one-18-oic acid 20-(ethylene glycol)-ketal (18----11) lactone (8a) and its acetate 8b. Further reduction with diisobutylaluminum hydride afforded 3 alpha, 5 alpha-tetrahydroaldosterone-20-ketal (10a), which was directly hydrolyzed to 12a with dilute acid in tetrahydrofuran-dioxan. Periodate oxidation led to the gamma-etiolactone 14a, which was then further converted into 5 alpha-dihydroaldosterone-gamma-etiolactone (14c).

Calix[4]arene coated QCM sensors for detection of VOC emissions: Methylene chloride sensing studies.

PubMed

Temel, Farabi; Tabakci, Mustafa

2016-06-01

This paper describes the sensing studies of QCM sensors with coated some calixarene derivatives bearing different functional groups for some selected Volatile Organic Compounds (VOCs) such as acetone, acetonitrile, carbon tetrachloride, chloroform, methylene chloride (MC), N,N-dimethylformamide, 1,4-dioxane, ethanol, ethyl acetate, xylene, methanol, n-hexane and toluene. The initial experiments have revealed that whole the calix[4]arene modified QCM sensors exhibited strongest sensing ability to MC emissions. Thus, the detailed studies were performed for only MC emissions after the determination of relatively more effective calix-coated QCM sensors for MC emissions in aqueous media. The results demonstrated that QCM sensor coated with calix-7 bearing both amino and imidazole groups was most useful sensor for MC emissions with 54.1ppm of detection limit. Moreover, it was understood that cyclic structures, H-bonding capabilities and also good preorganization properties of calixarene derivatives played an important role in VOC sensing processes. Copyright © 2016 Elsevier B.V. All rights reserved.

Preparation of pure chitosan film using ternary solvents and its super absorbency.

PubMed

Wang, Xuejun; Lou, Tao; Zhao, Wenhua; Song, Guojun

2016-11-20

Chemical modification and graft copolymerization were commonly adopted to prepare super absorbent materials. However, physical microstructure of pure chitosan film was optimized to improve the water uptake capacity in this study. Chitosan films with micro-nanostructure were prepared by a ternary solvent system. The optimal process parameters are 1% acetic acid water solution: dioxane: dimethyl sulfoxide=90: 2.5: 7.5 (v/v/v) with chitosan concentration at 1.25% (w/v). The water uptake capacity of the chitosan film prepared under the optimal process parameters was 896g/g. The prepared chitosan films also exhibited high water uptake capacity in response to external stimuli such as temperature, pH and salt. This finding may provide another way for improving the water absorbency. The pure chitosan film may find potential applications especially in the fields of hygienic products and biomedicine due to its super water absorbency and nontoxicity. Copyright © 2016 Elsevier Ltd. All rights reserved.

Corona discharge ion mobility spectrometry with orthogonal acceleration time of flight mass spectrometry for monitoring of volatile organic compounds.

PubMed

Sabo, Martin; Matejčík, Štefan

2012-06-19

We demonstrate the application of corona discharge ion mobility spectrometry with orthogonal acceleration time of flight mass spectrometry (CD IMS-oaTOF) for volatile organic compounds (VOCs) monitoring. Two-dimensional (2D) IMS-oaTOF spectra of VOCs were recorded in nearly real time. The corona discharge atmospheric pressure chemical ionization (APCI) source was operated in positive mode in nitrogen and air. The CD ion source generates in air H(3)O(+)(H(2)O)(n) and NO(+). The NO(+) offers additional possibility for selective ionization and for an increase of the sensitivity of monoaromatic compounds. In addition to H(3)O(+)(H(2)O)(n) and NO(+), we have carried out ionization of VOCs using acetone as dopant gas ((CH(3))(2)COH(+)). Sixteen model VOCs (tetrahydrofuran, butanol, n-propanol, iso-propano, acetone, methanol, ethanol, toluene, benzene, amomnia, dioxan, triethylamine, acetonitrile, formaldehyde, m-xylene, 2,2,2-trifluoroethylamine) were tested using these ionization techniques.

Simultaneous determination of all-trans and 13-cis retinoic acids and their 4-oxo metabolites by adsorption liquid chromatography after solid-phase extraction.

PubMed

Lefebvre, P; Agadir, A; Cornic, M; Gourmel, B; Hue, B; Dreux, C; Degos, L; Chomienne, C

1995-04-07

All-trans retinoic acid (all-trans RA), the active metabolite of vitamin A, has been demonstrated to be an efficient alternative to chemotherapy in the treatment of acute promyelocytic leukemia (APL), the AML3 subtype of the FAB cytological classification. Complete remission is obtained by inducing terminal granulocytic differentiation of the leukemic cells. To study all-trans RA pharmacokinetics in patients with APL, a rapid, precise and selective high-performance liquid chromatographic (HPLC) assay was developed. This method is easy and shows good repeatability (C.V. = 8.41-12.44%), reproducibility (C.V. = 9.19-14.73%), accuracy (C.V. = 3.5-11%) and sensitivity with a detection limit of 5 pmol/ml. The analysis is performed using normal-phase HPLC in an isocratic mode with UV detection after solid-phase extraction on octadecyl (C18) columns. The mobile phase is hexane-dichloromethane-dioxane (78:18:4, v/v) containing 1% acetic acid.

Enthalpy characteristics of L-proline dissolution in certain water-organic mixtures at 298.15 K

NASA Astrophysics Data System (ADS)

Badelin, V. G.; Smirnov, V. I.

2017-01-01

A thermochemical study of the processes of L-proline dissolution in aqueous solutions of acetonitrile, 1,4-dioxane, acetone, dimethyl sulfoxide, nitromethane and tetrahydrofuran at T = 298.15 K in the range of organic solvent concentrations x2 = 0-0.25 mole fractions is performed. Standard values of the enthalpies of solution and transfer of L-proline from water to mixed solvent, and the enthalpy coefficients of pairwise interactions between L-proline and molecules of organic solvents, are calculated. The effect the composition of a water-organic mixture and the structure of organic solvents have on the enthalpy characteristics of L-proline dissolution and transfer is examined. The effect the energy properties of intermolecular interactions between components of a mixed solvent has on the intermolecular interactions between L-proline and molecules of cosolvent is estimated. The correlation between the enthalpy characteristics of L-proline dissolution and electron-donor properties of organic cosolvent in aqueous solutions is determined.

Cometabolic bioremediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hazen, Terry C.

2009-02-15

Cometabolic bioremediation is probably the most under appreciated bioremediation strategy currently available. Cometabolism strategies stimulate only indigenous microbes with the ability to degrade the contaminant and cosubstrate e.g. methane, propane, toluene and others. This highly targeted stimulation insures that only those microbes that can degrade the contaminant are targeted, thus reducing amendment costs, well and formation plugging, etc. Cometabolic bioremediation has been used on some of the most recalcitrant contaminants, e.g. PCE, TCE, MTBE, TNT, dioxane, atrazine, etc. Methanotrophs have been demonstrated to produce methane monooxygense, an oxidase that can degrade over 300 compounds. Cometabolic bioremediation also has the advantagemore » of being able to degrade contaminants to trace concentrations, since the biodegrader is not dependent on the contaminant for carbon or energy. Increasingly we are finding that in order to protect human health and the environment that we must remediate to lower and lower concentrations, especially for compounds like endocrine disrupters, thus cometabolism may be the best and maybe the only possibility that we have to bioremediate some contaminants.« less

Ethylenedioxy Homologs of N-Methyl-(3,4-methylenedioxyphenyl)-2-aminopropane (MDMA) and its Corresponding Cathinone Analog Methylenedioxymethcathinone: Interactions with Transporters for Serotonin, Dopamine, and Norepinephrine

PubMed Central

Del Bello, Fabio; Sakloth, Farhana; Partilla, John S.; Baumann, Michael H.; Glennon, Richard A.

2015-01-01

N -Methyl-(3,4-methylenedioxyphenyl)-2-aminopropane (MDMA; ‘Ecstasy’; 1) and its β-keto analog methylone (MDMC; 2) are popular drugs of abuse. Little is known about their ring-expanded ethylenedioxy homologs. Here, we prepared N-methyl-(3,4-ethylenedioxyphenyl)-2-aminopropane (EDMA; 3), both of its optical isomers, and β-keto EDMA (i.e., EDMC; 4) to examine their effects at transporters for serotonin (SERT), dopamine (DAT), and norepinephrine (NET). In general, ring-expansion of the methylenedioxy group led to a several-fold reduction in potency at all three transporters. With respect to EDMA (3), S(+)3 was 6-fold, 50-fold, and 8-fold more potent than its R(−) enantiomer at SERT, DAT, and NET, respectively. Overall, in the absence of a β-carbonyl group, the ethylenedioxy (i.e., 1,4-dioxane) substituent seems better accommodated at SERT than at DAT and NET. PMID:26233799

Laser performance of Coumarin 540A dye molecules in polymeric host media with different viscosities: From liquid solution to solid polymer matrix

DOE Office of Scientific and Technical Information (OSTI.GOV)

Costela, A.; Garcia-Moreno, I.; Barroso, J.

1998-01-01

Photophysical parameters and lasing properties of Coumarin 540A dye molecules are studied in solutions of increasing viscosity, from liquid solutions in 1,4-dioxane to solid solutions in poly(methyl methacrylate). The fluorescence quantum yield and lasing efficiencies decrease as the viscosity of the solution increases, reflecting the strong influence of the rigidity of the medium on the radiative processes. The photodegradation mechanisms acting on the fluorophores are analyzed by following the dependence of laser induced fluorescence and laser output on the number of pump laser pulses. The fluorescence redistribution after pattern photobleaching technique is used, and Fick{close_quote}s second law is applied tomore » study the diffusion of dye molecules in the highly viscous polymer solutions. The diffusion coefficients of the dye molecules as a function of the increased viscosity of the medium are determined. {copyright} {ital 1998 American Institute of Physics.}« less

Thermodynamic Parameters of the Dissolution of 4-Hydroxy-L-Proline and L-Phenylalanine in Mixed Aqueous Solvents at 298 K

NASA Astrophysics Data System (ADS)

Smirnov, V. I.; Badelin, V. G.

2018-01-01

The enthalpies of solution of 4-hydroxy-L-proline and L-phenylalanine in binary mixed aqueous solvents containing acetonitrile (AN), 1,4-dioxane (1,4-DO), or acetone (AC) at mole fractions of 0 to 0.25 are determined at T = 298.15 K via isothermal calorimetry. The standard enthalpies of solution (Δsol H°) and transfer (Δtr H°) of 4-hydroxy-L-proline and L-phenylalanine from water to mixed aqueous solvents are calculated using the experimental calorimetric data, as are the enthalpy coefficients of paired interactions ( h xy ) between the molecules of the investigated amino acids and the organic solvents. The effects the mixed aqueous solvent composition and the structure of the organic solvent molecules have on the enthalpies of solution and transfer for the investigated amino acids are considered. The correlation between the enthalpy of solution of the amino acids and the electron-donating properties of the organic solvents in the mixed aqueous solvent systems is established.

Lidar Probing of the Mesosphere: Simultaneous Observations of Sporadic Sodium and Iron Formations, Calcium Ion Layers, Neutral Temperature and Winds

NASA Technical Reports Server (NTRS)

Kane, Timothy J.; Qian, Jun; Scherrer, Daniel R.; Senft, Daniel C.; Pfenninger, W. Matthew; Papen, George C.; Gardner, Chester S.

1992-01-01

Meteoritic ablation in the upper atmosphere is the commonly accepted source of the mesospheric metals between 80 and 105 km. The vertical and temporal behavior of some of these metals can be probed with high accuracy and resolution using resonance fluorescence lidar techniques. Of considerable interest in recent years has been the sporadic and rapid formation of thin, dense enhancements in these metallic layers. Since late Mar. 1991, the UIUC CEDAR lidar system, located at the Urbana Atmospheric Observatory, has been routinely operating at the Fe resonance line of 372 nm in order to probe the mesospheric Fe layer. In Nov. 1991, the capability to investigate mesospheric Ca(+) at the resonance line of 393.4 nm was added. The lidar's eximer-pumped dye laser uses Exciton QUI laser dye dissolved in p-dioxane, which can lase at both the Fe and Ca(+) frequencies. Various aspects of this investigation are discussed.

Attachment chemistry of aromatic compounds on a Silicon(100) surface

NASA Astrophysics Data System (ADS)

Henriksson, Anders; Nishiori, Daiki; Maeda, Hiroaki; Miyachi, Mariko; Yamanoi, Yoshinori; Nishihara, Hiroshi

2018-03-01

A mild method was developed for the chemical attachment of aromatic compounds directly onto a hydrogen-terminated Si(100) (H-Si(100)) surface. In the presence of palladium catalyst and base, 4-iodophenylferrocene and a π-conjugated iron complex were attached to H-Si(100) electrodes and hydrogen-terminated silicon nanowires (H-SiNWs), both of which have predominant dihydride species on their surfaces. The reactions were conducted in 1,4-dioxane at 100 °C and the immobilization of both 4-ferrocenylphenyl group and π-conjugated molecular wires were confirmed and quantified by XPS and electrochemical measurements. We reported densely packed monolayer whose surface coverage (Γ), estimated from the electrochemical measurements are in analogue to similar monolayers prepared via thermal or light induced hydrosilylation reactions with alkenes or alkynes. The increase in electrochemical response observed on nanostructured silicon surfaces corresponds well to the increase in surface area, those strongly indicating that this method may be applied for the functionalization of electrodes with a variety of surface topographies.

Effect of solvent, electronic, and steric factors on the reactivity of 1,1'-diethylferrocene, 1,1'-diacetylferrocene, and 1,1'-bis(diphenylphosphino)ferrocene towards hydrogen peroxide

NASA Astrophysics Data System (ADS)

Fomin, V. M.; Kochetkova, K. S.; Galkina, M. S.

2017-07-01

The oxidation of Fc(C2H5)2, Fc(COCH3)2, and Fc(PPh2)2, where Fc is a ferrocene, with hydrogen peroxide in aprotic (dioxane and acetonitrile) and hydroxyl-containing (ethanol, acetonitrile-water, and water) solvents is studied via electron spectroscopy. The reactivity of these metal complexes relative to an oxidant is due to the electron-donor or electron-acceptor properties of substituents, their sizes, and their capability for the specific solvation by a particular solvent. Possible mechanisms of the oxidation of metal complexes are discussed. When Fc(PPh2)2 is oxidized, the formation of ferrocenyl cation Fc+(PPh2)2 is due to the redox isomerism of ferrocenylphosphonium cation Fc(PPh2)P+Ph2, which can form during the reaction between protonated complex Fc(PPh2)P(H+)Ph2 and H2O2.

Acid- and base-catalysis in the mononuclear rearrangement of some (Z)-arylhydrazones of 5-amino-3-benzoyl-1,2,4-oxadiazole in toluene: effect of substituents on the course of reaction.

PubMed

D'Anna, Francesca; Frenna, Vincenzo; Ghelfi, Franco; Marullo, Salvatore; Spinelli, Domenico

2011-04-15

The reaction rates for the rearrangement of eleven (Z)-arylhydrazones of 5-amino-3-benzoyl-1,2,4-oxadiazole 3a-k into the relevant (2-aryl-5-phenyl-2H-1,2,3-triazol-4-yl)ureas 4a-k in the presence of trichloroacetic acid or of piperidine have been determined in toluene at 313.1 K. The results have been related to the effect of the aryl substituent by using Hammett and/or Ingold-Yukawa-Tsuno correlations and have been compared with those previously collected in a protic polar solvent (dioxane/water) as well as with those on the analogous rearrangement of the corresponding (Z)-arylhydrazones of 3-benzoyl-5-phenyl-1,2,4-oxadiazole 1a-k in benzene. Some light can thus be shed on the general differences of chemical reactivity between protic polar (or dipolar aprotic) and apolar solvents.

Hydroperoxide Traces in Common Cyclic Ethers as Initiators for Controlled RAFT Polymerizations.

PubMed

Eggers, Steffen; Abetz, Volker

2018-04-01

Herein, a reversible addition-fragmentation chain transfer (RAFT) polymerization is introduced for reactive monomers like N-acryloylpyrrolidine or N,N-dimethylacrylamide working without a conventional radical initiator. As a very straightforward proof of principle, the method takes advantage of the usually inconvenient radical-generating hydroperoxide contaminations in cyclic ethers like tetrahydrofuran or 1,4-dioxane, which are very common solvents in polymer sciences. The polymerizations are surprisingly well controlled and the polymers can be extended with a second block, indicating their high livingness. "Solvent-initiated" RAFT polymerizations hence prove to be a feasible access to tailored materials with minimal experimental effort and standard laboratory equipment, only requiring the following ingredients: hydroperoxide-contaminated solvent, monomer, and RAFT agent. In other respects, however, the potential coinitiating ability of the used solvent is to be considered when investigating the kinetics of RAFT polymerizations or aiming for the synthesis of high-livingness polymers, e.g., multiblock copolymers. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and in Vitro Antifungal Activity against Botrytis cinerea of Geranylated Phenols and Their Phenyl Acetate Derivatives

PubMed Central

Chávez, María I.; Soto, Mauricio; Taborga, Lautaro; Díaz, Katy; Olea, Andrés F.; Bay, Camila; Peña-Cortés, Hugo; Espinoza, Luis

2015-01-01

The inhibitory effects on the mycelial growth of plant pathogen Botritys cinerea have been evaluated for a series of geranylphenols substituted with one, two and three methoxy groups in the aromatic ring. The results show that the antifungal activity depends on the structure of the geranylphenols, increasing from 40% to 90% by increasing the number of methoxy groups. On the other hand, the acetylation of the –OH group induces a change of activity that depends on the number of methoxy groups. The biological activity of digeranyl derivatives is lower than that exhibited by the respective monogeranyl compound. All tested geranylphenols have been synthesized by direct coupling of geraniol and the respective phenol. The effect of solvent on yields and product distribution is discussed. For monomethoxyphenols the reaction gives better yields when acetonitrile is used as a solvent and AgNO3 is used as a secondary catalyst. However, for di- and trimethoxyphenols the reaction proceeds only in dioxane. PMID:26287171

The use of white-rot fungi as active biofilters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Braun-Luellemann, A.; Johannes, C.; Majcherczyk, A.

1995-12-31

White-rot fungi, growing on lignocellulosic substrates, have been successfully used as active organisms in biofilters. Filters using these fungi have a very high biological active surface area, allowing for high degrees of retention, a comparatively low pressure drop, and a high physical stability. The unspecific action of the extracellular enzymes of the white-rot fungi allows for the degradation of a wide variety of substances by the same organism. Degradation of several compounds in the gas phase by the white-rot fungi Trametes versicolor, Pleurotus ostreatus, Bjerkandera adusta, and Phanerochaete chrysosporium was tested. Among the aromatic solvents, styrene was the compound thatmore » was most readily degraded, followed by ethylbenzene, xylenes, and toluene. Tetrahydrofuran and dichloromethane were also degraded, whereas dioxane could not be attacked by fungi under the conditions used. Acrylonitrile and aniline were degraded very well, whereas pyridine was resistant to degradation. The process for removing styrene is now in the scaling-up stage.« less

Reversible Addition Fragmentation Chain Transfer (RAFT) Polymerization of 4-Vinylbenzaldehyde

PubMed Central

Sun, Guorong; Cheng, Chong; Wooley, Karen L.

2008-01-01

The direct reversible addition fragmentation chain transfer (RAFT) polymerization of 4-vinylbenzaldehyde (VBA) was established as a new synthetic method for the preparation of well-defined poly(vinylbenzaldehyde) (PVBA), a polymer having reactive aldehyde side chain substiuents. RAFT polymerization of VBA was investigated using S-1-dodecyl-S’-(α,α’-dimethyl-α”-acetic acid)trithiocarbonate (DDMAT) as chain transfer agent (CTA) and 2,2′-azobis(isobutyronitrile) (AIBN) as initiator in 1,4-dioxane or 2-butanone at 70-75 °C for 7.5-22.5 h. With 45-76% of monomer conversion, the resulting PVBA had well controlled number-average molecular weight (Mn) and low polydispersity (PDI < 1.17). The living characteristic of the RAFT polymerization process was confirmed by the linearity between the Mn values of PVBA and monomer conversions. Well-defined PVBA was further used as a macromolecular chain transfer agent (macro-CTA) in RAFT polymerization of styrene (St), and a block copolymer PVBA-b-PSt with relatively low polydispersity (PDI = 1.20) was successfully synthesized. PMID:19066633

Amorphous Solid Dispersion of Epigallocatechin Gallate for Enhanced Physical Stability and Controlled Release.

PubMed

Cao, Yizheng; Teng, Jing; Selbo, Jon

2017-11-09

Epigallocatechin gallate (EGCG) has been recognized as the most prominent green tea extract due to its healthy influences. The high instability and low bioavailability, however, strongly limit its utilization in food and drug industries. This work, for the first time, develops amorphous solid dispersion of EGCG to enhance its bioavailability and physical stability. Four commonly used polymeric excipients are found to be compatible with EGCG in water-dioxane mixtures via a stepwise mixing method aided by vigorous mechanical interference. The dispersions are successfully generated by lyophilization. The physical stability of the dispersions is significantly improved compared to pure amorphous EGCG in stress condition (elevated temperature and relative humidity) and simulated gastrointestinal tract environment. From the drug release tests, one of the dispersions, EGCG-Soluplus ® 50:50 ( w / w ) shows a dissolution profile that only 50% EGCG is released in the first 20 min, and the remains are slowly released in 24 h. This sustained release profile may open up new possibilities to increase EGCG bioavailability via extending its elimination time in plasma.

Combinatorial Discovery of Cosolvent Systems for Production of Narrow Dispersion Thiolate-Protected Gold Nanoparticles

PubMed Central

2015-01-01

The effect of aqueous solvent concentration in the synthesis of water-soluble thiolate-protected gold nanoparticles (AuNPs) was investigated for 13 water-miscible solvents and three thiolate ligands (p-mercaptobenzoic acid, thiomalic acid, and glutathione). The results were analyzed by construction of heat maps that rank each reaction result for polydispersity. When solvents were organized in the heat map according to their Dimroth–Reichardt ET parameter (an approximate measure of polarity), two “hot spots” become apparent that are independent of the ligand used. We speculate that one hot spot may arise in part from the metal chelation or coordination ability of solvents that include diglyme, 1,2-dimethoxyethane, 1,4-dioxane, and tetrahydrofuran. The second hot spot arises at concentrations of alcohols including 2-propanol and 1-butanol that appear to selectively precipitate a growing product, presumably stopping its growth at a certain size. We observe some tightly dispersed products that appear novel. Overall, this study expands the number of tightly dispersed water-soluble AuNPs that can be directly synthesized. PMID:25459632

Combinatorial discovery of cosolvent systems for production of narrow dispersion thiolate-protected gold nanoparticles.

PubMed

Wong, O Andrea; Compel, W Scott; Ackerson, Christopher J

2015-01-12

The effect of aqueous solvent concentration in the synthesis of water-soluble thiolate-protected gold nanoparticles (AuNPs) was investigated for 13 water-miscible solvents and three thiolate ligands (p-mercaptobenzoic acid, thiomalic acid, and glutathione). The results were analyzed by construction of heat maps that rank each reaction result for polydispersity. When solvents were organized in the heat map according to their Dimroth-Reichardt ET parameter (an approximate measure of polarity), two "hot spots" become apparent that are independent of the ligand used. We speculate that one hot spot may arise in part from the metal chelation or coordination ability of solvents that include diglyme, 1,2-dimethoxyethane, 1,4-dioxane, and tetrahydrofuran. The second hot spot arises at concentrations of alcohols including 2-propanol and 1-butanol that appear to selectively precipitate a growing product, presumably stopping its growth at a certain size. We observe some tightly dispersed products that appear novel. Overall, this study expands the number of tightly dispersed water-soluble AuNPs that can be directly synthesized.

Influence of different environments on the excited-state proton transfer and dual fluorescence of fisetin

NASA Astrophysics Data System (ADS)

Guharay, Jayanti; Dennison, S. Moses; Sengupta, Pradeep K.

1999-05-01

The influence of different protic and aprotic solvent environments on the excited-state intramolecular proton transfer (ESIPT) leading to a dual fluorescence behaviour of a biologically important, naturally occurring, polyhydroxyflavone, fisetin (3,3',4',7-tetrahydroxyflavone), has been investigated. The normal fluorescence band, in particular, is extremely sensitive to solvent polarity with νmax shifting from 24 510 cm -1 in dioxane ( ET(30)=36.0) to 20 790 cm -1 in methanol ( ET(30)=55.5). This is rationalized in terms of solvent dipolar relaxation process, which also accounts for the red edge excitation shifts (REES) observed in viscous environments such as glycerol at low temperatures. Significant solvent dependence of the tautomer fluorescence properties ( νmax, yield and decay kinetics) reveals the influence of external hydrogen bonding perturbation on the internal hydrogen bond of the molecule. These excited-state relaxation phenomena and their relevant parameters have been used to probe the microenvironment of fisetin in a membrane mimetic system, namely AOT reverse micelles in n-heptane at different water/surfactant molar ratio ( w0).

Advances in phytoremediation.

PubMed Central

Dietz, A C; Schnoor, J L

2001-01-01

Phytoremediation is the use of plants to remedy contaminated soils, sediments, and/or groundwater. Sorption and uptake are governed by physicochemical properties of the compounds, and moderately hydrophobic chemicals (logarithm octanol--water coefficients = 1.0--3.5) are most likely to be bioavailable to rooted, vascular plants. Some hydrophilic compounds, such as methyl-tert-butylether and 1,4-dioxane, may also be taken up by plants via hydrogen bonding with transpiration water. Organic chemicals that pass through membranes and are translocated to stem and leaf tissues may be converted (e.g., oxidized by cytochrome P450s), conjugated by glutathione or amino acids, and compartmentalized in plant tissues as bound residue. The relationship between metabolism of organic xenobiotics and toxicity to plant tissues is not well understood. A series of chlorinated ethenes is more toxic to hybrid poplar trees (Populus deltoides x nigra, DN-34) than are the corresponding chlorinated ethanes. Toxicity correlates best with the number of chlorine atoms in each homologous series. Transgenic plants have been engineered to rapidly detoxify and transform such xenobiotic chemicals. These could be used in phytoremediation applications if issues of cost and public acceptability are overcome. PMID:11250813

[Identification of components of the milky juice of Lactarius pergamenus (Fr.)Fr fungi by gas-liquid chromatography/mass spectrometry].

PubMed

Tsyvins'ka, M V; Panchak, L V; Stoĭka, R S; Antoniuk, V O

2013-01-01

The authors have proposed method of separation of methanol extract of Lactarius pergamenus basidiomes and investigation of fractions extracted with hexane which, according to our previous studies, possess the highest antiproliferative and antifungal activity. Main attention was given to fractionation and analysis by gas-liquid chromatography-mass spectrometry (GLC/MS) of the fraction 1.4 extracted with hexane. The key role in separation of this fraction was played by the use of dioxane which mixes well with both polar and nonpolar solvents (hexane, chloroform, methanol, water). Chemical composition of hexanoic fraction of methanol extract of dried basidomes Lactarius pergamenus fungi were completely characterized. It was found that this fraction consisted of 38% of fatty acids and their derivatives, 29%--of the phthalates, 13%--of the sesquiterpene, 2%--of aldehydes and 18%--of other compounds (hydrocarbons, alcohols, hydrazine derivatives and unidentified substances). Such combination of constituents allows forming a stable emulsion of milky juice which protects the mushroom fruit body from the bacterial and fungal infections and from eating by the mammalians and insects.

Simplex optimization of headspace factors for headspace gas chromatography determination of residual solvents in pharmaceutical products.

PubMed

Grodowska, Katarzyna; Parczewski, Andrzej

2013-01-01

The purpose of the present work was to find optimum conditions of headspace gas chromatography (HS-GC) determination of residual solvents which usually appear in pharmaceutical products. Two groups of solvents were taken into account in the present examination. Group I consisted of isopropanol, n-propanol, isobutanol, n-butanol and 1,4-dioxane and group II included cyclohexane, n-hexane and n-heptane. The members of the groups were selected in previous investigations in which experimental design and chemometric methods were applied. Four factors were taken into consideration in optimization which describe HS conditions: sample volume, equilibration time, equilibrium temperature and NaCl concentration in a sample. The relative GC peak area served as an optimization criterion which was considered separately for each analyte. Sequential variable size simplex optimization strategy was used and the progress of optimization was traced and visualized in various ways simultaneously. The optimum HS conditions appeared different for the groups of solvents tested, which proves that influence of experimental conditions (factors) depends on analyte properties. The optimization resulted in significant signal increase (from seven to fifteen times).

Anti-L. donovani activity in macrophage/amastigote model of palmarumycin CP18 and its large scale production.

PubMed

Ortega, Humberto E; Teixeira, Eliane de Morais; Rabello, Ana; Higginbotham, Sarah; Cubilla-Ríos, Luis

2014-01-01

Palmarumycin CP18, isolated from an extract of the fermentation broth and mycelium of the Panamanian endophytic fungus Edenia sp., was previously reported with strong and specific activity against Leishmania donovani. Here we report that when the same strain was cultured on different solid media--Harrold Agar, Leonian Agar, Potato dextrose Agar (PDA), Corn Meal Agar, Honey Peptone Agar, and eight vegetables (V8) Agar--in order to determine the optimal conditions for isolation of palmarumycin CP18, no signal for this compound was observed in any of the 1H NMR spectra of fractions obtained from these extracts. However, one extract, prepared from the fungal culture in PDA contained significant amounts of CJ-12,372, a possible biosynthetic precursor of palmarumycin CP18. Edenia sp. was cultivated on a large scale on PDA and CJ-12,372 was converted to palmarumycin CP18 by oxidation of its p-hydroquinone moiety with DDQ in dioxane. Palmarumycin CP18 showed anti-leishmanial activity against L. donovani in a macrophage/amastigote model, with IC50 values of 23.5 microM.

Advances in phytoremediation.

PubMed

Dietz, A C; Schnoor, J L

2001-03-01

Phytoremediation is the use of plants to remedy contaminated soils, sediments, and/or groundwater. Sorption and uptake are governed by physicochemical properties of the compounds, and moderately hydrophobic chemicals (logarithm octanol--water coefficients = 1.0--3.5) are most likely to be bioavailable to rooted, vascular plants. Some hydrophilic compounds, such as methyl-tert-butylether and 1,4-dioxane, may also be taken up by plants via hydrogen bonding with transpiration water. Organic chemicals that pass through membranes and are translocated to stem and leaf tissues may be converted (e.g., oxidized by cytochrome P450s), conjugated by glutathione or amino acids, and compartmentalized in plant tissues as bound residue. The relationship between metabolism of organic xenobiotics and toxicity to plant tissues is not well understood. A series of chlorinated ethenes is more toxic to hybrid poplar trees (Populus deltoides x nigra, DN-34) than are the corresponding chlorinated ethanes. Toxicity correlates best with the number of chlorine atoms in each homologous series. Transgenic plants have been engineered to rapidly detoxify and transform such xenobiotic chemicals. These could be used in phytoremediation applications if issues of cost and public acceptability are overcome.

Synthesis and click chemistry of a new class of biodegradable polylactide towards tunable thermo-responsive biomaterials.

PubMed

Zhang, Quanxuan; Ren, Hong; Baker, Gregory L

2015-02-28

A new class of clickable and biodegradable polylactide was designed and prepared via bulk polymerization of 3,6-dipropargyloxymethyl-1,4-dioxane-2,5-dione ( 1 ) which was synthesized from easily accessible propargyloxylactic acid ( 5 ). A homopolymer of 1 and random copolymer of 1 with l-lactide were obtained as amorphous materials and exhibit low T g of 8.5 and 34 °C, respectively, indicating their promising potentials for biomedical applications. The statistical nature of random copolymers was investigated by DSC analysis and 13 C NMR spectroscopy, which implies the random distribution of terminal alkyne groups along the back bone of copolymers. The efficient click post-modification of this new class of polylactide with alkyl and mPEG azides affords novel hydrophilic biomaterials, which exhibit reversible thermo-responsive properties as evidenced by their tunable LCST ranging from 22 to 69 °C depending on the balance of the incorporated hydrophilic/hydrophobic side chains. These results indicate the generality of this new class of clickable polylactide in preparing novel smart biomaterials in a simple and efficient manner via click chemistry.

Assessing acute toxicity of effluent from a textile industry and nearby river waters using sulfur-oxidizing bacteria in continuous mode.

PubMed

Gurung, Anup; Hassan, Sedky H A; Oh, Sang-Eun

2011-10-01

Bioassays are becoming an important tool for assessing the toxicity of complex mixtures of substances in aquatic environments in which Daphnia magna is routinely used as a test organism. Bioassays outweigh physicochemical analyses and are valuable in the decision-making process pertaining to the final discharge of effluents from wastewater treatment plants as they measure the total effect of the discharge which is ecologically relevant. In this study, the aquatic toxicity of a textile plant effluent and river water downstream from the plant were evaluated with sulfur-oxidizing bacterial biosensors in continuous mode. Collected samples were analysed for different physicochemical parameters and 1,4-dioxane was detected in the effluent. The effluent contained a relatively high chemical oxygen demand of 60 mg L(-1), which exceeded the limit set by the Korean government for industrial effluent discharges. Results showed that both the effluent and river waters were toxic to sulfur-oxidizing bacteria. These results show the importance of incorporating bioassays to detect toxicity in wastewater effluents for the sustainable management of water resources.

Synthesis of New Hydrated Geranylphenols and in Vitro Antifungal Activity against Botrytis cinerea

PubMed Central

Soto, Mauricio; Espinoza, Luis; Chávez, María I.; Díaz, Katy; Olea, Andrés F.; Taborga, Lautaro

2016-01-01

Geranylated hydroquinones and other geranylated compounds isolated from Aplydium species have shown interesting biological activities. This fact has prompted a number of studies where geranylated phenol derivatives have been synthesized in order to assay their bioactivities. In this work, we report the synthesis of a series of new hydrated geranylphenols using two different synthetic approaches and their inhibitory effects on the mycelial growth of Botrytis cinerea. Five new hydrated geranylphenols were obtained by direct coupling reaction between geraniol and phenol in dioxane/water and using BF3·Et2O as the catalyst or by the reaction of a geranylated phenol with BF3·Et2O. Two new geranylated quinones were also obtained. The synthesis and structural elucidation of all new compounds is presented. All hydrated geranylphenols efficiently inhibit the mycelial growth of B. cinerea. Their activity is higher than that observed for non-hydrated compounds. These results indicate that structural modification on the geranyl chain brings about an enhancement of the inhibition effect of geranylated phenol derivatives. PMID:27271604

Cooperation of Amphiphilicity and Crystallization for Regulating the Self-Assembly of Poly(ethylene glycol)-block-poly(lactic acid) Copolymers.

PubMed

Wang, Zhen; Cao, Yuanyuan; Song, Jiaqi; Xie, Zhigang; Wang, Yapei

2016-09-20

Tuning the amphiphilicity of block copolymers has been extensively exploited to manipulate the morphological transition of aggregates. The introduction of crystallizable moieties into the amphiphilic copolymers also offers increasing possibilities for regulating self-assembled structures. In this work, we demonstrate a detailed investigation of the self-assembly behavior of amphiphilic poly(ethylene glycol)-block-poly(l-lactic acid) (PEG-b-PLLA) diblock copolymers with the assistance of a common solvent in aqueous solution. With a given length of the PEG block, the molecular weight of the PLA block has great effect on the morphologies of self-assembled nanoaggregates as a result of varying molecular amphiphilicity and polymer crystallization. Common solvents including N,N-dimethylformamide, dioxane, and tetrahydrofuran involved in the early stage of self-assembly led to the change in chain configuration, which further influences the self-assembly of block copolymers. This study expanded the scope of PLA-based copolymers and proposed a possible mechanism of the sphere-to-lozenge and platelet-to-cylinder morphological transitions.

Amorphous Solid Dispersion of Epigallocatechin Gallate for Enhanced Physical Stability and Controlled Release

PubMed Central

Cao, Yizheng; Teng, Jing; Selbo, Jon

2017-01-01

Epigallocatechin gallate (EGCG) has been recognized as the most prominent green tea extract due to its healthy influences. The high instability and low bioavailability, however, strongly limit its utilization in food and drug industries. This work, for the first time, develops amorphous solid dispersion of EGCG to enhance its bioavailability and physical stability. Four commonly used polymeric excipients are found to be compatible with EGCG in water-dioxane mixtures via a stepwise mixing method aided by vigorous mechanical interference. The dispersions are successfully generated by lyophilization. The physical stability of the dispersions is significantly improved compared to pure amorphous EGCG in stress condition (elevated temperature and relative humidity) and simulated gastrointestinal tract environment. From the drug release tests, one of the dispersions, EGCG-Soluplus® 50:50 (w/w) shows a dissolution profile that only 50% EGCG is released in the first 20 min, and the remains are slowly released in 24 h. This sustained release profile may open up new possibilities to increase EGCG bioavailability via extending its elimination time in plasma. PMID:29120370

Structural and functional characterization of the CAP domain of pathogen-related yeast 1 (Pry1) protein

NASA Astrophysics Data System (ADS)

Darwiche, Rabih; Kelleher, Alan; Hudspeth, Elissa M.; Schneiter, Roger; Asojo, Oluwatoyin A.

2016-06-01

The production, crystal structure, and functional characterization of the C-terminal cysteine-rich secretory protein/antigen 5/pathogenesis related-1 (CAP) domain of pathogen-related yeast protein-1 (Pry1) from Saccharomyces cerevisiae is presented. The CAP domain of Pry1 (Pry1CAP) is functional in vivo as its expression restores cholesterol export to yeast mutants lacking endogenous Pry1 and Pry2. Recombinant Pry1CAP forms dimers in solution, is sufficient for in vitro cholesterol binding, and has comparable binding properties as full-length Pry1. Two crystal structures of Pry1CAP are reported, one with Mg2+ coordinated to the conserved CAP tetrad (His208, Glu215, Glu233 and His250) in spacegroup I41 and the other without divalent cations in spacegroup P6122. The latter structure contains four 1,4-dioxane molecules from the crystallization solution, one of which sits in the cholesterol binding site. Both structures reveal that the divalent cation and cholesterol binding sites are connected upon dimerization, providing a structural basis for the observed Mg2+-dependent sterol binding by Pry1.

Behavior of soluble and immobilized acid phosphatase in hydro-organic media.

PubMed

Wan, H; Horvath, C

1975-11-20

The hydrolysis of p-nitrophenyl phosphate by wheat germ acid phosphatase (orthophosphoric monoester phosphohydrolase, EC 3.1.3.2) has been investigated in mixtures of aqueous buffers with acetone, dioxane and acetonitrile. The enzyme was either in free solution or immobilized on a pellicular support which consisted of a porous carbonaceous layer on solid glass beads. The highest enzyme activity was obtained in acetone and acetonitrile mixed with citrate buffer over a wide range of organic solvent concentration. In 50% (v/v) acetone both V and Km of the immobilized enzyme were about half of the values in the neat aqueous buffer, but the Ki for inorganic phosphate was unchanged. In 50% (v/v) mixtures of various solvents and citrate buffers of different pH, the enzymic activity was found to depend on the pH of the aqueous buffer component rather than the pH of the hydro-organic mixture as measured with the glass-calomel electrode. The relatively high rates of p-nitrophenol liberation in the presence of glucose even at high organic solvent concentrations suggest that transphosphorylation is facilitated at low water activity.

Enzymatic preparation of novel thermoplastic di-block copolyesters containing poly[(R)-3-hydroxybutyrate] and poly(epsilon-caprolactone) blocks via ring-opening polymerization.

PubMed

Dai, Shiyao; Li, Zhi

2008-07-01

Enzymatic modification of a microbial polyester was achieved by the ring-opening polymerization of epsilon-caprolactone (CL) with low-molecular weight telechelic hydroxylated poly[( R)-3-hydroxybutyrate] (PHB-diol) as initiator and Novozym 435 (immobilized Candida antarctica Lipase B) as catalyst in anhydrous 1,4-dioxane or toluene. The ring-opening polymerization was investigated at different conditions with two different types of PHB-diols: PHB-diol(P), containing a primary OH and a secondary OH end groups, and PHB-diol(M), consisting of 91% PHB-diol(P) and 9% PHB-diol containing two secondary OH end groups. The reactions were followed by GPC analyses of the resulting polymers at different time points, and the optimal conditions were established to be 70 degrees C at a weight ratio of CL/enzyme/solvent of 8:1:24. The ring-opening polymerization of CL with PHB-diol(M) (Mn of 2380, NMR) at the molar ratio of 50:1 under the optimal conditions in 1,4-dioxane gave the corresponding poly[HB(56 wt %)-co-CL(44 wt %)] with Mn (NMR) of 3900 in 66% yield. Polymerization of CL and PHB-diol(P) ( Mn of 2010, NMR) at the same condition in toluene gave the corresponding poly[HB(28 wt %)-co-CL(72 wt %)] with Mn (NMR) of 7100 in 86% yield. Both polymers were characterized by (1)H and (13)C NMR and IR analyses as di-block copolyesters containing a PHB block with a secondary OH end group and a poly(epsilon-caprolactone) (PCL) block with a primary OH end group. NMR analyses and control experiments suggested no formation of random copolymers and no change of the PHB block during the reaction. The enzymatic ring-opening polymerization was selectively initiated by the primary OH group of PHB-diol, whereas the secondary OH group remained as an end group in the final polymers. The thermal properties of the di-block poly(HB-co-CL)s were analyzed by DSC, with excellent T g values for the elastomer domain: poly[HB(56 wt %)- co-CL(44 wt %)] with M n (NMR) of 3900 demonstrated a T g of -57 degrees C, Tm of 145, 123, and 53 degrees C; and poly[HB(28wt%)-co-CL(72wt%)] with Mn (NMR) of 7100 gave a Tg of -60 degrees C, Tm of 147 and 50 degrees C. Thus, the selective enzymatic ring-opening polymerization with PHB-diol as macro-initiator provides a new method for the preparation of PHB-based block copolymers as biomaterials with good thermoplastic properties and novel structures containing functional end groups.

Synthesis and characterization of polyphosphazene electrolytes including cyclic ether side groups

NASA Astrophysics Data System (ADS)

Fiedler, Carsten; Luerssen, Bjoern; Lucht, Brett; Janek, Juergen

2018-04-01

This paper presents the synthesis and detailed characterization of two polyphosphazene based polymers, including different cyclic ether side groups. The final polymers were obtained by a well-known method employing a living cationic polymerization and subsequent nucleophilic substitution. The synthesized polymers Poly [(1,3-dioxane-5-oxy) (1,3-dioxolane-4-methoxy)phosphazene] (DOPP) and Poly[bis(2-Tetrahydro-3-furanoxy)phosphazene] (THFPP) were mixed with varied amounts of lithium bis(trifluoromethane)sulfonamide (LiTFSI) and the interactions between the salt and the polymer chains were studied by Fourier transform infrared (FT-IR) and differential scanning calorimetry (DSC) measurements. Electrochemical characterization was performed by electrochemical impedance spectroscopy (EIS) and direct current polarization in the temperature range of 20-60 °C. These measurements were utilized to calculate the lithium transference number (t+), the lithium conductivity (σ) and its activation energy in order to elucidate the lithium transport behavior. Relatively high lithium transference numbers of 0.6 (DOPP) and 0.7 (THFPP) at 60 °C are found and reveal maximum lithium conductivities of 2.8·10-6 Sṡcm-1 and 9.0·10-7 Sṡcm-1 for DOPP and THFPP at 60 °C, respectively.

High laser efficiency and photostability of pyrromethene dyes mediated by nonpolar solvent.

PubMed

Gupta, Monika; Kamble, Priyadarshini; Rath, M C; Naik, D B; Ray, Alok K

2015-08-10

Many pyrromethene (PM) dyes have been shown to outperform established rhodamine dyes in terms of laser efficiency in the green-yellow spectral region, but their rapid photochemical degradation in commonly used ethanol or methanol solvents continues to limit its use in high average power liquid dye lasers. A comparative study on narrowband laser efficiency and photostability of commercially available PM567 and PM597 dyes, using nonpolar n-heptane and 1,4-dioxane and polar ethanol solvents, was carried out by a constructed pulsed dye laser, pumped by the second harmonic (532 nm) radiation of a Q-switched Nd:YAG laser. Interestingly, both nonpolar solvents showed a significantly higher laser photostability (∼100 times) as well as peak efficiency (∼5%) of these PM dyes in comparison to ethanol. The different photostability of the PM dyes was rationalized by determining their triplet-state spectra and capability to generate reactive singlet oxygen (O₂1) by energy transfer to dissolved oxygen in these solvents using pulse radiolysis. Heptane is identified as a promising solvent for these PM dyes for use in high average power dye lasers, pumped by copper vapor lasers or diode-pumped solid-state green lasers.

Mechanism of Positive Allosteric Modulators Acting on AMPA Receptors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jin,R.; Clark, S.; Weeks, A.

2005-01-01

Ligand-gated ion channels involved in the modulation of synaptic strength are the AMPA, kainate, and NMDA glutamate receptors. Small molecules that potentiate AMPA receptor currents relieve cognitive deficits caused by neurodegenerative diseases such as Alzheimer's disease and show promise in the treatment of depression. Previously, there has been limited understanding of the molecular mechanism of action for AMPA receptor potentiators. Here we present cocrystal structures of the glutamate receptor GluR2 S1S2 ligand-binding domain in complex with aniracetam [1-(4-methoxybenzoyl)-2-pyrrolidinone] or CX614 (pyrrolidino-1, 3-oxazino benzo-1, 4-dioxan-10-one), two AMPA receptor potentiators that preferentially slow AMPA receptor deactivation. Both potentiators bind within the dimermore » interface of the nondesensitized receptor at a common site located on the twofold axis of molecular symmetry. Importantly, the potentiator binding site is adjacent to the 'hinge' in the ligand-binding core 'clamshell' that undergoes conformational rearrangement after glutamate binding. Using rapid solution exchange, patch-clamp electrophysiology experiments, we show that point mutations of residues that interact with potentiators in the cocrystal disrupt potentiator function. We suggest that the potentiators slow deactivation by stabilizing the clamshell in its closed-cleft, glutamate-bound conformation.« less

Chemistry and structure of coal-derived asphaltenes, Phase III. Quarterly progress report, January--March 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yen, T. F.

1978-01-01

The solubility limits of Synthoil and PAMCO asphaltenes have been measured as a function of Hildebrand solubility parameters and hydrogen bonding. Solvents with moderate hydrogen bonding capacity such as dioxane, ethyl benzoate and dibutyl phthalate were found to be most effective in dissolving asphaltenes over the widest range of solubility parameters. VPO molecular weight studies of coal liquid derived carbenes, as a function of concentration in the solvent THF, indicate that these fractions are more strongly self-associated than the corresponding asphaltenes, and generally afford high infinite dilution number average molecular weights: Synthoil, 861; HRI H-Coal, 1156; Cat. Inc. SRC, 1228;more » PAMCO SRC, 1054. The variable ESR temperature dependence of the spin intensity for a Synthoil asphaltene-I/sub 2/ charge transfer followed a 1/T (Curie--Weiss) dependence over the temperature range from 25/sup 0/ to -114/sup 0/C suggesting that independent, non-interacting donor and acceptor doublets were formed. Weight percent OH values, determined from 'H NMR analysis of silylated asphaltenes, were found to provide a reasonably linear correlation with the absorbance of the monomeric OH infrared stretching bands of the asphaltenes.« less

Reverse osmosis followed by activated carbon filtration for efficient removal of organic micropollutants from river bank filtrate.

PubMed

Kegel, F Schoonenberg; Rietman, B M; Verliefde, A R D

2010-01-01

Drinking water utilities in Europe are faced with a growing presence of organic micropollutants in their water sources. The aim of this research was to assess the robustness of a drinking water treatment plant equipped with reverse osmosis and subsequent activated carbon filtration for the removal of these pollutants. The total removal efficiency of 47 organic micropollutants was investigated. Results indicated that removal of most organic micropollutants was high for all membranes tested. Some selected micropollutants were less efficiently removed (e.g. the small and polar NDMA and glyphosate, and the more hydrophobic ethylbenzene and napthalene). Very high removal efficiencies for almost all organic micropollutants by the subsequent activated carbon, fed with the permeate stream of the RO element were observed except for the very small and polar NDMA and 1,4-dioxane. RO and subsequent activated carbon filtration are complementary and their combined application results in the removal of a large part of these emerging organic micropollutants. Based on these experiments it can be concluded that the robustness of a proposed treatment scheme for the drinking water treatment plant Engelse Werk is sufficiently guaranteed.

Development and validation of a rapid capillary zone electrophoresis method for the determination of aconite alkaloids in aconite roots.

PubMed

Song, Jing-Zheng; Han, Quan-Bin; Qiao, Chun-Feng; But, Paul Pui-Hay; Xu, Hong-Xi

2010-01-01

Aconites, with aconite alkaloids as the major therapeutic and toxic components, are used for the treatment of analgesic, antirheumatic and neurological symptoms. Quantification of the aconite alkaloids is important for the quality control of aconite-containing drugs. To establish a validated capillary zone electrophoresis (CZE) method for the simultaneous determination of six major alkaloids, namely aconitine, mesaconitine, hypaconitine, benzoylaconine, benzoylmesaconine and benzoylhypaconine, in crude and processed aconite roots. The CZE method was optimised and validated using a stability-indicating method. The optimised running buffer was a mixture of 200 mm Tris, 150 mm perchloric acid and 40% 1,4-dioxane (pH 7.8) with the capillary thermostated at 25 degrees C. Using the optimised method, six aconite alkaloids were well separated. The established method showed good precision, accuracy and recovery. Contents of these alkaloids in crude and processed aconites were determined and it was observed that the levels of individual alkaloids varied between samples. The developed CZE method was reliable for the quality control of aconites contained in herbal medicines. The method could also be used as an approach for toxicological studies.

Iodination of insulin in aqueous and organic solvents

PubMed Central

Massaglia, A.; Rosa, U.; Rialdi, G.; Rossi, C. A.

1969-01-01

1. The iodination of insulin was studied under various experimental conditions in aqueous media and in some organic solvents, by measuring separately the uptake of iodine by the four tyrosyl groups and the relative amounts of monoiodotyrosine and di-iodotyrosine that are formed. In aqueous media from pH1 to pH9 the iodination occurs predominantly on the tyrosyl groups of the A chain. Some organic solvents increase the iodine uptake of the B-chain tyrosyl groups. Their efficacy in promoting iodination of Tyr-B-16 and Tyr-B-26 is in the order: ethylene glycol and propylene glycol≃methanol and ethanol>dioxan>8m-urea. 2. It is suggested that each of the four tyrosyl groups in insulin has a different environment: Tyr-A-14 is fully exposed to the solvent; Tyr-A-19 is sterically influenced by the environmental structure, possibly by the vicinity of a disulphide interchain bond; Tyr-B-16 is embedded into a non-polar area whose stability is virtually independent of the molecular conformation; Tyr-B-26 is probably in a situation similar to Tyr-B-16 with the difference that its non-polar environment depends on the preservation of the native structure. PMID:5346365

Structural Characterization of Lignin from Maize ( Zea mays L.) Fibers: Evidence for Diferuloylputrescine Incorporated into the Lignin Polymer in Maize Kernels.

PubMed

Del Río, José C; Rencoret, Jorge; Gutiérrez, Ana; Kim, Hoon; Ralph, John

2018-05-02

The structure of the phenolic polymer in maize grain fibers, with 5.5% Klason lignin content, has been studied. For this, the milled wood lignin (MWL) and dioxane lignin (DL) preparations were isolated and analyzed. The data indicated that the lignin in maize fibers was syringyl rich, mostly involved in β-aryl ether, resinol, and phenylcoumaran substructures. 2D NMR and derivatization followed by reductive cleavage (DFRC) also revealed the occurrence of associated ferulates together with trace amounts of p-coumarates acylating the γ-OH of lignin side chains, predominantly on S-lignin units. More interesting was the occurrence of diferuloylputrescine, a ferulic acid amide, which was identified by 2D NMR and comparison with a synthesized standard, that was apparently incorporated into this lignin. A phenylcoumaran structure involving a diferuloylputrescine coupled through 8-5' linkages to another diferuloylputrescine (or to a ferulate or a guaiacyl lignin unit) was found, providing compelling evidence for its participation in radical coupling reactions. The occurrence of diferuloylputrescine in cell walls of maize kernels and other cereal grains appears to have been missed in previous works, perhaps due to the alkaline hydrolysis commonly used for composition studies.

Silicon carbide passive heating elements in microwave-assisted organic synthesis.

PubMed

Kremsner, Jennifer M; Kappe, C Oliver

2006-06-09

Microwave-assisted organic synthesis in nonpolar solvents is investigated utilizing cylinders of sintered silicon carbide (SiC)--a chemically inert and strongly microwave absorbing material--as passive heating elements (PHEs). These heating inserts absorb microwave energy and subsequently transfer the generated thermal energy via conduction phenomena to the reaction mixture. The use of passive heating elements allows otherwise microwave transparent or poorly absorbing solvents such as hexane, carbon tetrachloride, tetrahydrofuran, dioxane, or toluene to be effectively heated to temperatures far above their boiling points (200-250 degrees C) under sealed vessel microwave conditions. This opens up the possibility to perform microwave synthesis in unpolar solvent environments as demonstrated successfully for several organic transformations, such as Claisen rearrangements, Diels-Alder reactions, Michael additions, N-alkylations, and Dimroth rearrangements. This noninvasive technique is a particularly valuable tool in cases where other options to increase the microwave absorbance of the reaction medium, such as the addition of ionic liquids as heating aids, are not feasible due to an incompatibility of the ionic liquid with a particular substrate. The SiC heating elements are thermally and chemically resistant to 1500 degrees C and compatible with any solvent or reagent.

Charge ordered insulating phases of DODHT salts with octahedral anions and a new radical salt, β''-(DODHT)2TaF6

NASA Astrophysics Data System (ADS)

Nishikawa, H.; Oshio, H.; Higa, M.; Kondo, R.; Kagoshima, S.; Nakao, A.; Sawa, H.; Yasuzuka, S.; Murata, K.

2008-10-01

Physical properties of isostructural β''-(DODHT)2X [DODHT = (l,4-dioxane-2,3-diyldithio)dihydrotetrathiafulvalene; X = PF6, AsF6, and SbF6] at ambient pressure have been compared. The insulating phase of β''-(DODHT)2PF6 salt has already been revealed to be a charge ordering (CO) state by X-ray diffraction study and magnetic behavior. CO in this salt was also confirmed by the observation of satellite reflections in oscillation photograph using synchrotron radiation. Transport property of β''-(DODHT)2SbF6 salt was reinvestigated up to the pressure of 3.7 GPa applied by a cubic anvil apparatus. Although the SbF6 salt turned to be metallic above 2.0 GPa, no superconductivity was observed. In order to examine the anion size dependence of DODHT salts with octahedral anions, we prepared a new DODHT salt, β''-(DODHT)2TaF6, which has the larger counter anion compared with the previous salts. Crystal structure of this salt was isostructural to the other DODHT salts. The electrical and magnetic properties of this salt were similar to those of β''-(DODHT)2SbF6 salt.

Spectroscopic studies on 2-[2-(4-methylquinolin-2-yl)hydrazono]-1,2-diphenylethanone molecule and its metal complexes

NASA Astrophysics Data System (ADS)

Seleem, H. S.; El-Inany, G. A.; Mousa, M.; Hanafy, F. I.

2009-11-01

The electronic absorption spectra of a hydrazone: 2-[2-(4-methylquinolin-2-yl)hydrazono]-1,2-diphenylethanone (BHQ) derived from 2-hydrazino-4-methylquinoline and 1,2-diphenylethan-1,2-dione (benzil) have been studied in various solvents of different polarities. The dependence of the band shift Δ ύ on the solvent parameters viz.D, Z, ET, DN, AN, α, β and π* was discussed. Also, the effect of pH on the free hydrazone and its Co(II), Ni(II) and Cu(II) complexes was studied spectrophotometrically in 75% (v/v) dioxane-water in order to determine the dissociation and stability constants. The stoichiometry of the formed complexes was determined by three different methods: Job's, mole ratio and slope ratio which indicate the formation of 1:2, M:L complexes for Co(II) and Cu(II) and 1:1, Ni(II):L. Beer's law is valid in the range 0.32-7.04 μg/mL depending on the type of the metal ion. The use of BHQ as an indicator via a spectrophotometric titration of Cu(II) and Ni(II) with EDTA was efficient.

C–C Cross-Coupling Reactions of O6-Alkyl-2-Haloinosine Derivatives and a One-Pot Cross-Coupling/O6-Deprotection Procedure

PubMed Central

Gurram, Venkateshwarlu; Pottabathini, Narender; Garlapati, Ramesh; Chaudhary, Avinash B.; Patro, Balaram; Lakshman, Mahesh K.

2012-01-01

Reaction conditions for the C–C cross-coupling of O6-alkyl-2-bromo- and 2-chloroinosine derivatives with aryl-, hetaryl-, and alkylboronic acids were studied. Optimization experiments with silyl-protected 2-bromo-O6-methylinosine led to the identification of [PdCl2(dcpf)]/K3PO4 in 1,4-dioxane as the best condition for these reactions (dcpf = 1,1’-bis(dicyclohexylphosphino)ferrocene). Attempted O6-demethylation, as well as the replacement of the C-6 methoxy group by amines, was unsuccessful, which led to the consideration of Pd-cleavable groups such that C–C cross-coupling and O6-deprotection could be accomplished in a single step. Thus, inosine 2-chloro-O6-allylinosine was chosen as the substrate and, after re-evaluation of the cross-coupling conditions with 2-chloro-O6-methylinosine as a model substrate, one-step C–C cross-coupling/deprotection reactions were performed with the O6-allyl analogue. These reactions are the first such examples of a one-pot procedure for the modification and deprotection of purine nucleosides under C–C cross-coupling conditions. PMID:22570232

Subnanosecond spectrofluorimetry of new indolocarbazole derivatives in solutions and protein complexes and their dipole moments

NASA Astrophysics Data System (ADS)

Nemkovich, N. A.; Kruchenok, Yu. V.; Sobchuk, A. N.; Detert, H.; Wrobel, N.; Chernyavskiĭ, E. A.

2009-08-01

The spectral and temporal characteristics of new 6,12-dimethoxyindolo[3,2- b]carbazole, 5,11-dimethyl-6,12-dimethoxyindolo[3,2- b]carbazole, and 5,11-dihexyl-6,12-di(hexyloxy)indolo[3,2- b]carbazole fluorescence probes in organic solvents and protein complexes are studied. The dipole moments of indolocarbazoles in 1,4-dioxane were measured by electrooptical absorption method. The measured dipole moments have values within the range of (3.1-3.6) × 10-30 C m in the equilibrium ground state and increase to (4.8-5.6) × 10-30 C m after excitation. The excited state lifetime of indolocarbazole derivatives increases with increasing polarity and viscosity of the environment. The binding of indolocarbazoles with trypsinogen and human serum albumin increases the fluorescence intensity, changes the intensity ratio of fluorescence bands, and increases the average excited state lifetime of indolocarbazoles. The analysis of the instantaneous fluorescence spectra and fluorescence decay parameters at different wavelengths revealed the existence of several types of probe binding sites in proteins. It is found that the fluorescence characteristics of indolocarbazole derivatives depend on the conformation rearrangements of trypsinogen due to its thermal denaturation.

Probing structure and dynamics of DNA with 2-aminopurine: effects of local environment on fluorescence.

PubMed

Rachofsky, E L; Osman, R; Ross, J B

2001-01-30

2-Aminopurine (2AP) is an analogue of adenine that has been utilized widely as a fluorescence probe of protein-induced local conformational changes in DNA. Within a DNA strand, this fluorophore demonstrates characteristic decreases in quantum yield and emission decay lifetime that vary sensitively with base sequence, temperature, and helix conformation but that are accompanied by only small changes in emission wavelength. However, the molecular interactions that give rise to these spectroscopic changes have not been established. To develop a molecular model for interpreting the fluorescence measurements, we have investigated the effects of environmental polarity, hydrogen bonding, and the purine and pyrimidine bases of DNA on the emission energy, quantum yield, and intensity decay kinetics of 2AP in simple model systems. The effects of environmental polarity were examined in a series of solvents of varying dielectric constant, and hydrogen bonding was investigated in binary mixtures of water with 1,4-dioxane or N,N-dimethylformamide (DMF). The effects of the purine and pyrimidine bases were studied by titrating 2AP deoxyriboside (d2AP) with the nucleosides adenosine (rA), cytidine (rC), guanosine (rG), and deoxythymidine (dT), and the nucleoside triphosphates ATP and GTP in neutral aqueous solution. The nucleosides and NTPs each quench the fluorescence of d2AP by a combination of static (affecting only the quantum yield) and dynamic (affecting both the quantum yield and the lifetime, proportionately) mechanisms. The peak wavelength and shape of the emission spectrum are not altered by either of these effects. The static quenching is saturable and has half-maximal effect at approximately 20 mM nucleoside or NTP, consistent with an aromatic stacking interaction. The rate constant for dynamic quenching is near the diffusion limit for collisional interaction (k(q) approximately 2 x 10(9) M(-1) s(-1)). Neither of these effects varies significantly between the various nucleosides and NTPs studied. In contrast, hydrogen bonding with water was observed to have a negligible effect on the emission wavelength, fluorescence quantum yield, or lifetime of 2AP in either dioxane or DMF. In nonpolar solvents, the fluorescence lifetime and quantum yield decrease dramatically, accompanied by significant shifts in the emission spectrum to shorter wavelengths. However, these effects of polarity do not coincide with the observed emission wavelength-independent quenching of 2AP fluorescence in DNA. Therefore, we conclude that the fluorescence quenching of 2AP in DNA arises from base stacking and collisions with neighboring bases only but is insensitive to base-pairing or other hydrogen bonding interactions. These results implicate both structural and dynamic properties of DNA in quenching of 2AP and constitute a simple model within which the fluorescence changes induced by protein-DNA binding or other perturbations may be interpreted.

Effects of the tumor-vasculature-disrupting agent verubulin and two heteroaryl analogues on cancer cells, endothelial cells, and blood vessels.

PubMed

Mahal, Katharina; Resch, Marcus; Ficner, Ralf; Schobert, Rainer; Biersack, Bernhard; Mueller, Thomas

2014-04-01

Two analogues of the discontinued tumor vascular-disrupting agent verubulin (Azixa®, MPC-6827, 1) featuring benzo-1,4-dioxan-6-yl (compound 5 a) and N-methylindol-5-yl (compound 10) residues instead of the para-anisyl group on the 4-(methylamino)-2-methylquinazoline pharmacophore, were prepared and found to exceed the antitumor efficacy of the lead compound. They were antiproliferative with single-digit nanomolar IC50 values against a panel of nine tumor cell lines, while not affecting nonmalignant fibroblasts. Indole 10 surpassed verubulin in seven tumor cell lines including colon, breast, ovarian, and germ cell cancer cell lines. In line with docking studies indicating that compound 10 may bind the colchicine binding site of tubulin more tightly (Ebind =-9.8 kcal mol(-1) ) than verubulin (Ebind =-8.3 kcal mol(-1) ), 10 suppressed the formation of vessel-like tubes in endothelial cells and destroyed the blood vessels in the chorioallantoic membrane of fertilized chicken eggs at nanomolar concentrations. When applied to nude mice bearing a highly vascularized 1411HP germ cell xenograft tumor, compound 10 displayed pronounced vascular-disrupting effects that led to hemorrhages and extensive central necrosis in the tumor. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Occupational exposure to airborne chemical substances in paintings conservators].

PubMed

Jezewska, Anna; Szewczyńska, Małgorzata; Woźnica, Agnieszka

2014-01-01

This paper presents the results of the quantitative study of the airborne chemical substances detected in the conservator's work environment. The quantitative tests were carried out in 6 museum easel paintings conservation studios. The air test samples were taken at various stages of restoration works, such as cleaning, doubling, impregnation, varnishing, retouching, just to name a few. The chemical substances in the sampled air were measured by the GC-FID (gas chromatography with flame ionization detector) test method. The study results demonstrated that concentrations of airborne substances, e.g., toluene, 1,4-dioxane, turpentine and white spirit in the work environment of paintings conservators exceeded the values allowed by hygiene standards. It was found that exposure levels to the same chemical agents, released during similar activities, varied for different paintings conservation studios. It is likely that this discrepancy resulted from the indoor air exchange system for a given studio (e.g. type of ventilation and its efficiency), the size of the object under maintenance, and also from the methodology and protection used by individual employees. The levels of organic solvent vapors, present in the workplace air in the course of painting conservation, were found to be well above the occupational exposure limits, thus posing a threat to the worker's health.

Low operational stability of enzymes in dry organic solvents: changes in the active site might affect catalysis.

PubMed

Bansal, Vibha; Delgado, Yamixa; Legault, Marc; Barletta, Gabriel

2012-02-14

The potential of enzyme catalysis in organic solvents for synthetic applications has been overshadowed by the fact that their catalytic properties are affected by organic solvents. In addition, it has recently been shown that an enzyme's initial activity diminishes considerably after prolonged exposure to organic media. Studies geared towards understanding this last drawback have yielded unclear results. In the present work we decided to use electron paramagnetic resonance spectroscopy (EPR) to study the motion of an active site spin label (a nitroxide free radical) during 96 h of exposure of the serine protease subtilisin Carlsberg to four different organic solvents. Our EPR data shows a typical two component spectra that was quantified by the ratio of the anisotropic and isotropic signals. The isotropic component, associated with a mobile nitroxide free radical, increases during prolonged exposure to all solvents used in the study. The maximum increase (of 43%) was observed in 1,4-dioxane. Based on these and previous studies we suggest that prolonged exposure of the enzyme to these solvents provokes a cascade of events that could induce substrates to adopt different binding conformations. This is the first EPR study of the motion of an active-site spin label during prolonged exposure of an enzyme to organic solvents ever reported.

Photophysical parameters and laser performance of 3-(4‧-dimethylaminophenyl)-1-(2-furanyl)prop-2-en-1-one (DMAFP): A new laser dye

NASA Astrophysics Data System (ADS)

El-Daly, S. A.; Gaber, M.; El-Sayed, Y. S.

2009-09-01

The spectral properties such as singlet absorption, molar absorptivity, emission spectra, fluorescence quantum yield and excited state lifetime of 3-(4'-dimethylaminophenyl)-1-(2-furanyl)prop-2-en-1-one (DMAFP) have been determined in different solvents. DMAFP dye exhibits a large red shift in both electronic absorption and emission spectra as the solvent polarity increases, indicating a large change in the dipole moment of molecules upon excitation. A crystalline solid of DMAFP gives an excimer like emission at 566 nm due to the excitation of molecular aggregates. This is expected from the idealized crystal structure of the dye that belongs to the B-type class of Steven's classification. The ground and excited state protonation constants of DMAFP are calculated and amounted to 1.71 and 8.3, respectively. DMAFP acts as a good laser dye upon pumping with nitrogen laser ( λex=337.1 nm) in chloroform, methylene chloride and dioxane and gives laser emission in the range 460-590 nm. The laser parameters such as the tuning range, gain coefficient ( α), emission cross section ( σ e) and half-life energy ( E1/2) are calculated. The photoreactivity and net photochemical quantum yield of DMAFP in chloromethane solvents are also studied.

Mixed ligand coordination polymers with flexible bis-imidazole linker and angular sulfonyldibenzoate: Crystal structure, photoluminescence and photocatalytic activity

NASA Astrophysics Data System (ADS)

Bisht, Kamal Kumar; Rachuri, Yadagiri; Parmar, Bhavesh; Suresh, Eringathodi

2014-05-01

Four ternary coordination polymers (CPs) namely, {[Ni(SDB)(BITMB)(H2O)]·H2O}n (CP1), {[Cd(SDB)(BITMB) (H2O)]·(THF)(H2O)}n (CP2), {[Zn2(SDB)2(BITMB)]·(THF)2}n (CP3) and {[Co2(SDB)2(BITMB)]·(Dioxane)3}n (CP4) composed of angular dicarboxylate SDB (4,4'-sulfonyldibenzoate) and N-donor BITMB (1,3-bis(imidazol-1-ylmethyl)-2,4,6-trimethyl benzene) have been synthesized by solvothermal reactions and characterized by single crystal X-ray diffraction and other physico-chemical techniques. CP1 possesses one-dimensional ribbon type metal-organic motifs glued together by H-bonds and π⋯π interactions, whereas CP2-CP4, exhibit non-interpenetrated sql networks supported by weak supramolecular interactions. Structural diversity of these CPs can be attributed to the coordination geometry adopted by the metal nodes, versatile coordination modes of SDB and conformational flexibility of BITMB. Solid state luminescence properties of CP1-CP4 were explored. Photocatalytic performance of all CPs for the decomposition of metanil yellow by dilute hydrogen peroxide in the presence of visible light was also investigated. 25-83% dye removal from aqueous solutions in the presence of CP1-CP4 was observed.

Cyanoketene and Iminopropadienones.

PubMed

Moloney, Daniel W. J.; Wong, Ming Wah; Flammang, Robert; Wentrup, Curt

1997-06-27

Cyanoketene (8) is generated in high yields on flash vacuum thermolysis (FVT) of suitably substituted Meldrum's acid derivatives (5-[(alkylamino)(methylthio or alkylamino)methylene]-2,2-dimethyl-1,3-dioxane-4,6-diones) (3e-j), and also on FVT of cyanoacetic acid derivatives 9e,f,g,j,k,m. The major reaction pathway from 3 proceeds via ketenimines 6 and (alkylimino)propadienones 7, the latter undergoing a retro-ene reaction to 8. A minor pathway is via imidoylketenes 4e,h and oxoketenimines 5e,h, which undergo retro-ene reactions to 9. All intermediates were characterized by Ar matrix FTIR and tandem mass spectrometry (collisional activation MS). Trapping of 4, 5, and 8 with nucleophiles is also reported. The preference of 1,3-X shifts over 1,5-H shifts in imidoylketenes 12 (X = SMe or NMe(2)) is corroborated by the calculated activation barriers. Neat cyanoketene is highly reactive, reacting at or below 80 K, and this is attributed to the availability of a low-lying ketene LUMO. The IR spectrum of cyanoketene (Ar, 14 K) is dominated by two absorptions at 2163 (s; C=C=O) and 2239 (w; CN) cm(-)(1) in excellent agreement with density functional (B3-LYP/6-31G) and ab initio (QCISD/6-31G) calculations.

TEMPO addition into pre-irradiated fluoropolymers and living-radical graft polymerization of styrene for preparation of polymer electrolyte membranes

NASA Astrophysics Data System (ADS)

Sawada, Shin-ichi; Suzuki, Akihiro; Terai, Takayuki; Maekawa, Yasunari

2010-04-01

We prepared proton exchange membranes (PEMs) by 2,2,6,6-tetramethylpiperidinyl-1-oxy (TEMPO)-mediated living-radical graft polymerization (LRGP) of styrene into fluoropolymer films and subsequent sulfonation. Poly(vinylidene fluoride) (PVDF) and poly(ethylene- co-tetrafluoroethylene) (ETFE) films were first irradiated and then treated with TEMPO solutions in various solvents. TEMPO addition was confirmed by the test of styrene grafting into TEMPO-treated films at 60 °C, at which the LRGP never proceeds. This test enabled us to differentiate the LRGP from the conventional graft polymerization. In order to gain a deep insight about TEMPO-addition reaction, the TEMPO-penetration behavior into the base polymer films was examined by a permeation experiment and computer simulation. Xylene and dioxane were appropriate solvents for the complete introduction of TEMPO into PVDF and ETFE films, respectively. Then, the LRGP of styrene was performed based on the fully TEMPO-capped films at 125 °C with various solvents. By using an alcoholic solvent, the degree of grafting was enhanced and it reached a maximum of 38%. This grafted film was sulfonated to prepare a PEM showing an ion exchange capacity of 2.2 meq/g and proton conductivity of 1.6×10 -1 S/cm.

Absorption spectral analysis of 4f-4f transitions for the complexation of Pr(III) and Nd(III) with thiosemicarbazide in absence and presence of Zn(II) in aqueous and organic solvents

NASA Astrophysics Data System (ADS)

Anita, K.; Rajmuhon Singh, N.

2011-10-01

The complexation of thiosemicarbazide with Pr(III) and Nd(III) in absence and presence of Zn(II), a soft metal ion in aqueous and organic solvents like CH 3OH,CH 3CN, dioxane (C 4H 8O 2) and DMF (C 3H 7NO) and their equimolar mixtures are discussed by employing absorption difference and comparative absorption spectrophotometry. Complexation of thiosemicarbazide with Pr(III) and Nd(III) is indicated by the changes in the absorption intensity following the subsequent changes in the oscillator strength of different 4f-4f bands and Judd-Ofelt intensity ( Tλ) parameters. The other spectral parameters like energy interaction parameters namely Slater-Condon ( Fk), Racah ( Ek), Lande ( ξ4f), Nephelauxetic ratio ( β) and bonding parameters ( b1/2) are further computed to explain the nature of complexation. The difference in the energy parameters with respect to donor atoms and solvents reveal that the chemical environment around the lanthanide ions has great impact on f-f transition and any change in the environment result in modification of the spectra. Various solvents and their equimolar mixtures are also used to discuss the participation of solvents in the complexation.

A new intermediate in the Prins reaction

PubMed Central

Fukuda, Takeshi; Yamazaki, Shoko

2013-01-01

Summary Two Prins reactions were investigated by the use of DFT calculations. A model composed of R–CH=CH2 + H3O+(H2O)13 + (H2C=O)2, R = Me and Ph, was adopted to trace reaction paths. For both alkenes, the concerted path forming 1,3-diols was obtained as the rate determining step (TS1). TS stands for a transition state. From the 1,3-diol, a bimolecular elimination (TS2) leads to the allylic alcohol as the first channel. In the second channel, the 1,3-diol was converted via TS3 into an unprecedented hemiacetal intermediate, HO–CH2–O–CH(R)–CH2–CH2–OH. This intermediate undergoes ring closure (TS4), affording the 1,3-dioxane product. The intermediate is of almost the same stability as the product, and two species were suggested to be in a state of equilibrium. While the geometry of TS1 appears to be forwarded to that of a carbocation intermediate, the cation disappeared through the enlargement of the water cluster. Dynamical calculations of a classical trajectory using the atom-centered density matrix propagation molecular dynamics model on the four TSs were carried out, and results of IRC calculations were confirmed by them. PMID:23532354

Epistemology of Contaminants of Emerging Concern and Literature Meta-analysis

PubMed Central

Halden, Rolf U.

2014-01-01

A meta-analysis was conducted to inform the epistemology, or theory of knowledge, of contaminants of emerging concern (CECs). The CEC terminology acknowledges the existence of harmful environmental agents whose identities, occurrences, hazards, and effects are not sufficiently understood. Here, data on publishing activity were analyzed for 12 CECs, revealing a common pattern of emergence, suitable for identifying past years of peak concern and forecasting future ones: dichlorodiphenyltrichloroethane (DDT; 1972, 2008), trichloroacetic acid (TCAA; 1972, 2009), nitrosodimethylamine (1984), methyl tert-butyl ether (2001), trichloroethylene (2005), perchlorate (2006), 1,4-dioxane (2009), prions (2009), triclocarban (2010), triclosan (2012), nanomaterials (by 2016), and microplastics (2022 ± 4). CECs were found to emerge from obscurity to the height of concern in 14.1 ± 3.6 years, and subside to a new baseline level of concern in 14.5 ± 4.5 years. CECs can emerge more than once (e.g., TCAA, DDT) and the multifactorial process of emergence may be driven by inception of novel scientific methods (e.g., ion chromatography, mass spectrometry and nanometrology), scientific paradigm shifts (discovery of infectious proteins), and the development, marketing and mass consumption of novel products (antimicrobial personal care products, microplastics and nanomaterials). Publishing activity and U.S. regulatory actions were correlated for several CECs investigated. PMID:25294779

Comparative Kinetic Study and Microwaves Non-Thermal Effects on the Formation of Poly(amic acid) 4,4′-(Hexafluoroisopropylidene)diphthalic Anhydride (6FDA) and 4,4′-(Hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline (BAPHF). Reaction Activated by Microwave, Ultrasound and Conventional Heating

PubMed Central

Tellez, Hugo Mendoza; Alquisira, Joaquín Palacios; Alonso, Carlos Rius; Cortés, José Guadalupe López; Toledano, Cecilio Alvarez

2011-01-01

Green chemistry is the design of chemical processes that reduce or eliminate negative environmental impacts. The use and production of chemicals involve the reduction of waste products, non-toxic components, and improved efficiency. Green chemistry applies innovative scientific solutions in the use of new reagents, catalysts and non-classical modes of activation such as ultrasounds or microwaves. Kinetic behavior and non-thermal effect of poly(amic acid) synthesized from (6FDA) dianhydride and (BAPHF) diamine in a low microwave absorbing p-dioxane solvent at low temperature of 30, 50, 70 °C were studied, under conventional heating (CH), microwave (MW) and ultrasound irradiation (US). Results show that the polycondensation rate decreases (MW > US > CH) and that the increased rates observed with US and MW are due to decreased activation energies of the Arrhenius equation. Rate constant for a chemical process activated by conventional heating declines proportionally as the induction time increases, however, this behavior is not observed under microwave and ultrasound activation. We can say that in addition to the thermal microwave effect, a non-thermal microwave effect is present in the system. PMID:22072913

Quantitative treatment of the solvent effects on the electronic absorption and fluorescence spectra of acridines and phenazines. The ground and first excited singlet-state dipole moments

NASA Astrophysics Data System (ADS)

Aaron, Jean Jacques; Maafi, Mounir; Párkányi, Cyril; Boniface, Christian

1995-04-01

Electronic absorption and fluorescence excitation and emission spectra of four acridines (acridine, Acridine Yellow, 9-aminoacridine and proflavine) and three phenazines (phenazine, neutral Red and safranine) are determined at room temperature (298 K) in several solvents of various polarities (dioxane, chloroform, ethyl ether, ethyl acetate, 1-butanol, 2-propanol, ethanol, methanol, dimethylformamide, acetonitrile and dimethyl sulfoxide). The effect of the solvent upon the spectral characteristics of the above compounds, is studied. In combination with the ground-state dipole moments of these compounds, the spectral data are used to evaluate their first excited singlet-state dipole moments by means of the solvatochromic shift method (Bakhshiev's and Kawski-Chamma-Viallet's correlations). The theoretical ground and excited singlet-state dipole moments for acridines and phenazines are also calculated as a vector sum of the π-component (obtained by the PPP method) and the σ-component (obtained from σ-bond moments). For most acridines and phenazines under study, the experimental excited singlet-state dipole moments are found to be higher than their ground state counterpart. The application of the Kamlet-Abboud-Taft solvatochromic parameters to the solvent effect on spectral properties of acridine and phenazine derivatives is discussed.

Cosmetics use and age at menopause: Is there a connection?

PubMed Central

Chow, Erika; Mahalingaiah, Shruthi

2016-01-01

Short Narrative Abstract Cosmetics contain a vast number of chemicals, most of which are not under the regulatory purview of the Food and Drug Administration. Only a few of these chemicals have been evaluated for potential deleterious health impact – parabens, phthalates, polycyclic aromatic hydrocarbons, and siloxanes. A review of the ingredients in the best-selling and top rated products of the top beauty brands in the world, as well as a review of highlighted chemicals by non-profit environmental organizations reveal 11 chemicals and chemical families of concern: butylated hydroxyanisole/butylated hydroxytoluene, coal tar dyes, diethanolamine, formaldehyde releasing preservatives, parabens, phthalates, 1,4 dioxane, polycyclic aromatic hydrocarbons, siloxanes, talc/asbestos, and triclosan. Age at menopause can be affected by a variety of mechanisms, including endocrine disruption, failure of DNA repair, oxidative stress, shortened telomere length, and ovarian toxicity. There is a lack of available studies to make a conclusion regarding cosmetics use and age at menopause. What little data there is suggests future studies are warranted. Women with chronic and consistent use of cosmetics across their lifespan may be a population of concern. More research is required to better elucidate the relationship and time windows of vulnerability and the effects of mixtures and combinations of products on ovarian health. PMID:27545020

Real-time mass spectroscopy analysis of Li-ion battery electrolyte degradation under abusive thermal conditions

NASA Astrophysics Data System (ADS)

Gaulupeau, B.; Delobel, B.; Cahen, S.; Fontana, S.; Hérold, C.

2017-02-01

The lithium-ion batteries are widely used in rechargeable electronic devices. The current challenges are to improve the capacity and safety of these systems in view of their development to a larger scale, such as for their application in electric and hybrid vehicles. Lithium-ion batteries use organic solvents because of the wide operating voltage. The corresponding electrolytes are usually based on combinations of linear, cyclic alkyl carbonates and a lithium salt such as LiPF6. It has been reported that in abusive thermal conditions, a catalytic effect of the cathode materials lead to the formation fluoro-organics compounds. In order to understand the degradation phenomenon, the study at 240 °C of the interaction between positive electrode materials (LiCoO2, LiNi1/3Mn1/3Co1/3O2, LiMn2O4 and LiFePO4) and electrolyte in dry and wet conditions has been realized by an original method which consists in analyzing by mass spectrometry in real time the volatile molecules produced. The evolution of specific gases channels coupled to the NMR reveal the formation of rarely discussed species such as 2-fluoroethanol and 1,4-dioxane. Furthermore, it appears that the presence of water or other protic impurities greatly influence their formation.

Synthesis, characterization and non-isothermal decomposition kinetic of a new galactochloralose based polymer.

PubMed

Kök, Gökhan; Ay, Kadir; Ay, Emriye; Doğan, Fatih; Kaya, Ismet

2014-01-30

A glycopolymer, poly(3-O-methacroyl-5,6-O-isopropylidene-1,2-O-(S)-trichloroethylidene-α-d-galactofuranose) (PMIPTEG) was synthesized from the sugar-carrying methacrylate monomer, 3-O-methacroyl-5,6-O-isopropylidene-1,2-O-(S)-trichloroethylidene-α-d-galactofuranose (MIPTEG) via conventional free radical polymerization with AIBN in 1,4-dioxane. The structures of glycomonomer and their polymers were confirmed by UV-vis, FT-IR, (1)H NMR, (13)C NMR, GPC, TG/DTG-DTA, DSC, and SEM techniques. SEM images showed that PMIPTEG had a straight-chain length structure. On the other hand, the thermal decomposition kinetics of polymer were investigated by means of thermogravimetric analysis in dynamic nitrogen atmosphere at different heating rates. The apparent activation energies for thermal decomposition of the PMIPTEG were calculated using the Kissinger, Kim-Park, Tang, Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS) and Friedman methods and were found to be 100.15, 104.40, 102.0, 102.2, 103.2 and 99.6 kJ/mol, respectively. The most likely process mechanism related to the thermal decomposition stage of PMIPTEG was determined to be a Dn deceleration type in terms of master plots results. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparative 4f-4f absorption spectral study for the interactions of Nd(III) with some amino acids: Preliminary thermodynamics and kinetic studies of interaction of Nd(III):glycine with Ca(II)

NASA Astrophysics Data System (ADS)

Moaienla, T.; Bendangsenla, N.; David Singh, Th.; Sumitra, Ch.; Rajmuhon Singh, N.; Indira Devi, M.

2012-02-01

Spectral analysis of Nd(III) complexes with some amino acids viz.; glycine, L-alanine, L-phenylalanine and L-aspartic acid in the presence and absence of Ca 2+ was carried out in some organic solvents; CH 3OH, CH 3CN, DMF and dioxane using comparative absorption spectra of 4f-4f transitions. The study was carried out by evaluating various energy interaction parameters like Slator-Condon ( Fk), Lande factor ( ξ4f), nephelauxetic ratio ( β), bonding parameter ( b1/2), percent-covalency ( δ) by applying partial and multiple regression analysis. The values of oscillator strength ( Pobs) and Judd-Ofelt electric dipole intensity parameter Tλ ( λ = 2, 4, 6) for different 4f-4f transitions have been calculated. On analysis of the variation of the various energy interaction parameters as well as the changes in the oscillator strength ( Pobs) and Tλ values, reveal the mode of binding with the different ligands. Kinetic studies for the complexation of Nd(III):glycine:Ca(II) have also been discussed at different temperatures in DMF medium and from it the values of activation energy ( Ea) and thermodynamic parameters like Δ H°, Δ S° and Δ G° for the complexation are evaluated.

Muscadine grape seed oil as a novel source of tocotrienols to reduce adipogenesis and adipocyte inflammation.

PubMed

Zhao, Lu; Yagiz, Yavuz; Xu, Changmou; Lu, Jiang; Chung, Soonkyu; Marshall, Maurice R

2015-07-01

Tocotrienols are unsaturated forms of vitamin E previously shown to reduce adipogenesis and adipose inflammation. In this study, muscadine grape seed oil (MGSO) was identified as a novel source of tocotrienols containing significant amounts of α- and γ-tocotrienol (T3) with minor seasonal changes. The aim of this study was to assess the anti-adipogenic and anti-inflammatory potential of MGSO by using primary human adipose-derived stem cells (hASCs). Differentiating hASCs were treated with MGSO and compared with rice bran and olive oil. Accumulation of triglyceride was significantly lower in MGSO-treated hASCs than rice bran and olive oils. A tocotrienol rich fraction (TRF) from MGSO was prepared by solid phase extraction and eluted with 15% 1,4-dioxane in hexane. The MGSO-derived TRF treatment significantly reduced mRNA and protein expression that are crucial to adipogenesis (e.g., PPARγ and aP2) in hASCs. Furthermore, TRF from MGSO markedly reduced LPS-induced proinflammatory gene expression in human adipocytes and cytokine secretion to the medium (IL-6 and IL-8). Collectively, our work suggests that MGSO is a stable and reliable natural source of T3 and MGSO may constitute a new dietary strategy to attenuate obesity and its associated adipose inflammation.

Optimization of the fabrication of novel stealth PLA-based nanoparticles by dispersion polymerization using D-optimal mixture design

PubMed Central

Adesina, Simeon K.; Wight, Scott A.; Akala, Emmanuel O.

2015-01-01

Purpose Nanoparticle size is important in drug delivery. Clearance of nanoparticles by cells of the reticuloendothelial system has been reported to increase with increase in particle size. Further, nanoparticles should be small enough to avoid lung or spleen filtering effects. Endocytosis and accumulation in tumor tissue by the enhanced permeability and retention effect are also processes that are influenced by particle size. We present the results of studies designed to optimize crosslinked biodegradable stealth polymeric nanoparticles fabricated by dispersion polymerization. Methods Nanoparticles were fabricated using different amounts of macromonomer, initiators, crosslinking agent and stabilizer in a dioxane/DMSO/water solvent system. Confirmation of nanoparticle formation was by scanning electron microscopy (SEM). Particle size was measured by dynamic light scattering (DLS). D-optimal mixture statistical experimental design was used for the experimental runs, followed by model generation (Scheffe polynomial) and optimization with the aid of a computer software. Model verification was done by comparing particle size data of some suggested solutions to the predicted particle sizes. Results and Conclusion Data showed that average particle sizes follow the same trend as predicted by the model. Negative terms in the model corresponding to the crosslinking agent and stabilizer indicate the important factors for minimizing particle size. PMID:24059281

Optimization of the fabrication of novel stealth PLA-based nanoparticles by dispersion polymerization using D-optimal mixture design.

PubMed

Adesina, Simeon K; Wight, Scott A; Akala, Emmanuel O

2014-11-01

Nanoparticle size is important in drug delivery. Clearance of nanoparticles by cells of the reticuloendothelial system has been reported to increase with increase in particle size. Further, nanoparticles should be small enough to avoid lung or spleen filtering effects. Endocytosis and accumulation in tumor tissue by the enhanced permeability and retention effect are also processes that are influenced by particle size. We present the results of studies designed to optimize cross-linked biodegradable stealth polymeric nanoparticles fabricated by dispersion polymerization. Nanoparticles were fabricated using different amounts of macromonomer, initiators, crosslinking agent and stabilizer in a dioxane/DMSO/water solvent system. Confirmation of nanoparticle formation was by scanning electron microscopy (SEM). Particle size was measured by dynamic light scattering (DLS). D-optimal mixture statistical experimental design was used for the experimental runs, followed by model generation (Scheffe polynomial) and optimization with the aid of a computer software. Model verification was done by comparing particle size data of some suggested solutions to the predicted particle sizes. Data showed that average particle sizes follow the same trend as predicted by the model. Negative terms in the model corresponding to the cross-linking agent and stabilizer indicate the important factors for minimizing particle size.

Synthesis of monodentate ferrocenylphosphines and their application to the palladium-catalyzed Suzuki reaction of aryl chlorides.

PubMed

Pickett, Tom E; Roca, Francesc X; Richards, Christopher J

2003-04-04

Racemic and enantiopure ((p)()S)-1-bromo-2-methylferrocene 6 were synthesized in 4 steps from 2-(4,4-dimethyloxazolinyl)ferrocene and (S)-2-(4-methylethyloxazolinyl)ferrocene, respectively (46 and 81% overall yield). Bromolithium exchange and addition of ClPR(2) gave the corresponding racemic or enantiopure 2-methylferrocenyl phosphine ligands 2-MeFcPR(2) 11 (R = Ph), 12 (R = Cy), and 13 (R = (t)Bu) in 28-93% yield. Use of PCl(3) gave the C(3)-symmetric phosphine (2-MeFc)(3)P 5 from ((p)()S)-6(72% yield) but racemic 6 did not lead to the formation of triferrocenyl phosphines. Combination of 5 and Pd(2)(dba)(3) gave an active catalyst for the Suzuki reaction of aryl chlorides, for example, 4-chlorotoluene and phenylboronic acid reacted at only 60 degrees C in dioxane (86% yield). Other examples are reported together with the use of 12 in this same protocol. From the X-ray crystal structure of 5 the cone angle was determined as 211 degrees. With this, and the electronic character of 11, 12, and other phosphines (derived from nu(CO) of trans-[(R(3)P)(2)Rh(CO)Cl]), an analysis is made of the steric and electronic influences on ligand activity in the Suzuki reaction.

C-C cross-coupling reactions of O6-alkyl-2-haloinosine derivatives and a one-pot cross-coupling/O6-deprotection procedure.

PubMed

Gurram, Venkateshwarlu; Pottabathini, Narender; Garlapati, Ramesh; Chaudhary, Avinash B; Patro, Balaram; Lakshman, Mahesh K

2012-08-01

Reaction conditions for the CC cross-coupling of O(6)-alkyl-2-bromo- and 2-chloroinosine derivatives with aryl-, hetaryl-, and alkylboronic acids were studied. Optimization experiments with silyl-protected 2-bromo-O(6)-methylinosine led to the identification of [PdCl(2)(dcpf)]/K(3)PO(4) in 1,4-dioxane as the best conditions for these reactions (dcpf=1,1'-bis(dicyclohexylphosphino)ferrocene). Attempted O(6)-demethylation, as well as the replacement of the C-6 methoxy group by amines, was unsuccessful, which led to the consideration of Pd-cleavable groups such that C-C cross-coupling and O(6)-deprotection could be accomplished in a single step. Thus, inosine 2-chloro-O(6)-allylinosine was chosen as the substrate and, after re-evaluation of the cross-coupling conditions with 2-chloro-O(6)-methylinosine as a model substrate, one-step C-C cross-coupling/deprotection reactions were performed with the O(6)-allyl analogue. These reactions are the first such examples of a one-pot procedure for the modification and deprotection of purine nucleosides under C-C cross-coupling conditions. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Poly(ethylene glycol)-grafted cyclic acetals based polymer networks with non-water-swellable, biodegradable and surface hydrophilic properties.

PubMed

Yin, Ruixue; Zhang, Nan; Wu, Wentao; Wang, Kemin

2016-05-01

Cyclic acetals based biomaterial without acidic products during hydrolytic degradation is a promising candidate for tissue engineering applications; however, low hydrophilicity is still one limitation for its biomedical application. In this work, we aim to achieve non-water-swellable cyclic acetal networks with improved hydrophilicity and surface wettability by copolymerization of cyclic acetal units based monomer, 5-ethyl-5-(hydroxymethyl)-β,β-dimethyl-1, 3-dioxane-2-ethanol diacrylate (EHD) and methoxy poly(ethylene glycol) monoacrylate (mPEGA) under UV irradiation, to avoid swelling of conventional hydrogels which could limit their applicability in particular of the mechanical properties and geometry integrity. Various EHD/mPEGA networks were fabricated with different concentrations of mPEGA from 0 to 30%, and the results showed photopolymerization behavior, mechanical property and thermal stability could not be significantly affected by addition of mPEGA, while the surface hydrophilicity was dramatically improved with the increase of mPEGA and could achieve a water contact angle of 37° with 30% mPEGA concentration. The obtained EHD/mPEGA network had comparative degradation rate to the PECA hydrogels reported previously, and MTT assay indicated it was biocompatible to L929 cells. Copyright © 2016 Elsevier B.V. All rights reserved.

Polymorphs and solvatomorphs of azilsartan medoxomil: Elucidation of solvent-induced construction and conformational diversity

NASA Astrophysics Data System (ADS)

Zhang, Xian-Rui; He, Sai-Fei; Zhang, Shuo; Li, Jing; Li, Shan; Liu, Jin-Song; Zhang, Lei

2017-02-01

Two polymorphs (AM-A and AM-B) of azilsartan medoxomil (AM) and four AM solvatomorphs with toluene (AM-TOL), 1,4-dioxane (AM-DIO), chloroform (AM-TCM) and N,N-dimethylacetamide (AM-DMA) have been prepared by the hydrolysis of azilsartan medoxomil potassium in aqueous-organic solutions. In the crystal structures of two polymorphs and three solvatomorphs (AM-TOL, AM-DIO and AM-TCM), two asymmetric AM molecules form the dimeric cycle-like structures via intermolecular Nsbnd H⋯N hydrogen bonds in R22 (26) ring, while AM-DMA shows intramolecular Nsbnd H⋯O hydrogen bond between AM and DMA molecules. The hydrogen bonds (Csbnd H⋯O or Csbnd H⋯N) and π···π (or Csbnd H···π) interactions are helpful to stabilize the conformational diversity of AM. The solvent-induced experiment shows that solvent molecules have great influence on the solvatomorph formation and DIO can form the most steady solvatomorph than other solvents. The thermal study demonstrates that toluene molecules in three solvatomorphs (AM-TOL, AM-DIO and AM-TCM) are the most difficult to remove from the cage. Our results illustrate that the solvent plays significant role in tuning the size of the cage and producing the conformational diversity of AM molecules.

Reduced graphene oxide-mediated Z-scheme BiVO4/CdS nanocomposites for boosted photocatalytic decomposition of harmful organic pollutants.

PubMed

Clament Sagaya Selvam, N; Kim, Yeong Gyeong; Kim, Dong Jin; Hong, Won-Hwa; Kim, Woong; Park, Sung Hyuk; Jo, Wan-Kuen

2018-09-01

The efficient photocatalytic degradation of harmful organic pollutants (isoniazid (ISN) and 1,4-dioxane (DX)) via the Z-scheme electron transfer mechanism was accomplished using a photostable composite photocatalyst consisting of BiVO 4 , CdS, and reduced graphene oxide (RGO). Compared to their pristine counterparts, the RGO-mediated Z-scheme CdS/BiVO 4 (CdS/RGO-BiVO 4 ) nanocomposites exhibited superior degradation activities, mainly attributed to the prolonged charge separation. RGO was found to be involved in visible-light harvesting and acted as a solid-state electron mediator at the CdS/BiVO 4 interface to realize an effective Z-scheme electron transfer pathway, avoid photocatalyst self-oxidation, and lengthen the life span of charge carriers. The results of reactive species scavenging experiments, photoluminescence measurements, and transient photocurrent measurements, as well as the calculated band potentials of the synthesized photocatalysts, supported the Z-scheme electron/hole pair separation mechanism. Additionally, the intermediates formed during the degradation of ISN and DX were identified, and a possible fragmentation pattern was proposed. This systematic work aims to develop photostable Z-scheme composites as unique photocatalytic systems for the efficient removal of harmful organic pollutants. Copyright © 2018 Elsevier B.V. All rights reserved.

Comparative kinetic study and microwaves non-thermal effects on the formation of poly(amic acid) 4,4'-(hexafluoroisopropylidene)diphthalic anhydride (6FDA) and 4,4'-(hexafluoroisopropylidene)bis(p-phenyleneoxy)dianiline (BAPHF). Reaction activated by microwave, ultrasound and conventional heating.

PubMed

Tellez, Hugo Mendoza; Alquisira, Joaquín Palacios; Alonso, Carlos Rius; Cortés, José Guadalupe López; Toledano, Cecilio Alvarez

2011-01-01

Green chemistry is the design of chemical processes that reduce or eliminate negative environmental impacts. The use and production of chemicals involve the reduction of waste products, non-toxic components, and improved efficiency. Green chemistry applies innovative scientific solutions in the use of new reagents, catalysts and non-classical modes of activation such as ultrasounds or microwaves. Kinetic behavior and non-thermal effect of poly(amic acid) synthesized from (6FDA) dianhydride and (BAPHF) diamine in a low microwave absorbing p-dioxane solvent at low temperature of 30, 50, 70 °C were studied, under conventional heating (CH), microwave (MW) and ultrasound irradiation (US). Results show that the polycondensation rate decreases (MW > US > CH) and that the increased rates observed with US and MW are due to decreased activation energies of the Arrhenius equation. Rate constant for a chemical process activated by conventional heating declines proportionally as the induction time increases, however, this behavior is not observed under microwave and ultrasound activation. We can say that in addition to the thermal microwave effect, a non-thermal microwave effect is present in the system.

Molecular imprinting of enzymes with water-insoluble ligands for nonaqueous biocatalysis.

PubMed

Rich, Joseph O; Mozhaev, Vadim V; Dordick, Jonathan S; Clark, Douglas S; Khmelnitsky, Yuri L

2002-05-15

Attaining higher levels of catalytic activity of enzymes in organic solvents is one of the major challenges in nonaqueous enzymology. One of the most successful strategies for enhancing enzyme activity in organic solvents involves tuning the enzyme active site by molecular imprinting with substrates or their analogues. Unfortunately, numerous imprinters of potential importance are poorly soluble in water, which significantly limits the utility of this method. In the present study, we have developed strategies that overcome this limitation of the molecular-imprinting technique and that thus expand its applicability beyond water-soluble ligands. The solubility problem can be addressed either by converting the ligands into a water-soluble form or by adding relatively high concentrations of organic cosolvents, such as tert-butyl alcohol and 1,4-dioxane, to increase their solubility in the lyophilization medium. We have succeeded in applying both of these strategies to produce imprinted thermolysin, subtilisin, and lipase TL possessing up to 26-fold higher catalytic activity in the acylation of paclitaxel and 17beta-estradiol compared to nonimprinted enzymes. Furthermore, we have demonstrated for the first time that molecular imprinting and salt activation, applied in combination, produce a strong additive activation effect (up to 110-fold), suggesting different mechanisms of action involved in these enzyme activation techniques.

An automated parallel crystallisation search for predicted crystal structures and packing motifs of carbamazepine.

PubMed

Florence, Alastair J; Johnston, Andrea; Price, Sarah L; Nowell, Harriott; Kennedy, Alan R; Shankland, Norman

2006-09-01

An automated parallel crystallisation search for physical forms of carbamazepine, covering 66 solvents and five crystallisation protocols, identified three anhydrous polymorphs (forms I-III), one hydrate and eight organic solvates, including the single-crystal structures of three previously unreported solvates (N,N-dimethylformamide (1:1); hemi-furfural; hemi-1,4-dioxane). Correlation of physical form outcome with the crystallisation conditions demonstrated that the solvent adopts a relatively nonspecific role in determining which polymorph is obtained, and that the previously reported effect of a polymer template facilitating the formation of form IV could not be reproduced by solvent crystallisation alone. In the accompanying computational search, approximately half of the energetically feasible predicted crystal structures exhibit the C=O...H--N R2(2)(8)dimer motif that is observed in the known polymorphs, with the most stable correctly corresponding to form III. Most of the other energetically feasible structures, including the global minimum, have a C=O...H--N C(4) chain hydrogen bond motif. No such chain structures were observed in this or any other previously published work, suggesting that kinetic, rather than thermodynamic, factors determine which of the energetically feasible crystal structures are observed experimentally, with the kinetics apparently favouring nucleation of crystal structures based on the CBZ-CBZ R2(2)(8) motif. (c) 2006 Wiley-Liss, Inc. and the American Pharmacists Association.

Fabrication and characterization of poly(DL-lactic-co-glycolic acid)/zirconia-hybridized amorphous calcium phosphate composites

PubMed Central

WHITED, BRYCE M.; GOLDSTEIN, AARON S.; SKRTIC, DRAGO; LOVE, BRIAN J.

2010-01-01

Several minerals, such as hydroxyapatite and β-tricalcium phosphate, have been incorporated into bioresorbable polyester bone scaffolds to increase the osteoconductivity both in vitro and in vivo. More soluble forms of calcium phosphate that release calcium and phosphate ions have been postulated as factors that increase osteoblast differentiation and mineralization. Recently, a zirconia-hybridized pyrophosphate-stabilized amorphous calcium phosphate (Zr-ACP) has been synthesized allowing controlled release of calcium and phosphate ions. When incorporated into bioresorbable scaffolds, Zr-ACP has the potential to induce osteoconductivity. In this study, 80–90% (w/v) porous poly(DL-LActic-co-glycolic acid) (PLGA) scaffolds were formed by thermal phase separation from dioxane while incorporating Zr-ACP. Scanning electron microscopy revealed a highly porous structure with a pore size ranging from a few μm to about 100 μm, smaller than we had hoped for. Zr-ACP particles were evenly dispersed in the composite structure and incorporated into the pore walls. The amorphous structure of the Zr-ACP was maintained during composite fabrication, as found by X-ray diffraction. Composite scaffolds had larger compressive yield strengths and moduli compared to pure polymer scaffolds. These initial efforts demonstrate that PLGA/Zr-ACP composites can be formed in ways that ultimately serve as promising bone scaffolds in tissue engineering. PMID:16768292

Conformational analysis of a synthetic fish kisspeptin 1 peptide in membrane mimicking environments

PubMed Central

Shahi, Neetu; Singh, Atul Kumar; Khangembam, Victoria Chanu; Singh, Arvind Kumar; Kumar, Satish

2017-01-01

Kisspeptin 1 is a neuropeptide hormone of the RFamide family, which act as an upstream regulator of brain-pituitary-gonad (BPG) axis in most vertebrates including teleosts. In the present study, a 16 amino acid long putative mature bioactive peptide (kiss 1) from preprokisspeptin 1 of golden mahseer, Tor putitora (Hamilton, 1822), was synthesized and characterized using an integrated (experimental and in silico) approach. The far-UV circular dichroism (CD) spectrum of this peptide was evaluated both in aqueous and membrane mimicking solvents (TFE, HFIP and Dioxane). The results indicate that kiss 1 peptide adopted helical, turn and β conformations in membrane like environments. The near-UV CD spectroscopy was also carried out to examine the tertiary packing around aromatic residues of kiss 1 peptide and the peptide-membrane complex. The kiss 1 peptide exhibited little signal in water, but a prominent negative band was observed at around 275 nm when membrane mimetic solution was added. The observed ordered conformations of kiss 1 peptide in the different solvents indicated its potential biological activity which could enhance the secretion of gonadotropin-releasing hormone (GnRH) at BPG axis. The conformational information generated from the present study reinforces the application prospects of bioactive synthetic peptide analogs of kisspeptin 1 in improving the reproductive performances of important cultivable fish species. PMID:28977030

In vitro toxicities of experimental jet fuel system ice-inhibiting agents.

PubMed

Geiss, K T; Frazier, J M

2001-07-02

One research emphasis within the Department of Defense has been to seek the replacement of operational compounds with alternatives that pose less potential risk to human and ecological systems. Alternatives to glycol ethers, such as diethylene glycol monomethyl ether (M-DE), were investigated for use as jet fuel system ice-inhibiting agents (FSIIs). This group of chemicals includes three derivatives of 1,3-dioxolane-4-methanol (M-1, M-2, and M-3) and a 1,3-dioxane (M-27). In addition, M-DE was evaluated as a reference compound. Our approach was to implement an in vitro test battery based on primary rat hepatocyte cultures to perform initial toxicity evaluations. Hepatocytes were exposed to experimental chemicals (0, 0.001, 0.01, 0.1, 1, 10 mM dosages) for periods up to 24 h. Samples were assayed for lactate dehydrogenase (LDH) release, MTT dye reduction activity, glutathione level, and rate of protein synthesis as indicators of toxicity. Of the compounds tested, M-1, especially at the 10-mM dose, appeared to be more potent than the other chemicals, as measured by these toxicity assays. M-DE, the current FSII, elicited little response in the toxicity assays. Although some variations in toxicity were observed at the 10-mM dose, the in vitro toxicities of the chemicals tested (except for M-1) were not considerably greater than that of M-DE.

Effect of proteolytic starter cultures as leavening agents of pizza dough.

PubMed

Pepe, O; Villani, F; Oliviero, D; Greco, T; Coppola, S

2003-08-01

Lactic acid bacteria (LAB) and yeasts were selected on the basis of in vitro proteolytic activity against wheat gluten protein and then assayed as leavening agents for pizza dough. Trials were carried out to compare a proteolytic starter (Prt(+)), consisting of Lactobacillus sakei T56, Weissella paramesenteroides A51 and Candida krusei G271, and a non-proteolytic starter (Prt(-)), consisting of Lb. sakei T58, W. paramesenteroides A58 and Saccharomyces cerevisiae T22. The proteolytic activity of the starter cultures was monitored immediately after mixing of the dough and throughout the fermentation process. The proteolytic activity was assessed by analysing the salt-soluble protein (SSP) and the dioxane-soluble protein (DSP) fractions of the pizza dough by discontinuous SDS-PAGE. Only the Prt(+) starter exhibited considerable qualitative and quantitative changes in the electrophoretic patterns of the protein fractions extracted. After the fermentation, the Prt(+) and Prt(-) doughs were tested to evaluate the influence of the proteolytic activity on the mechanical properties of the dough before and after baking. Indications emerged suggesting an influence of the proteolytic activity on the viscoelasticity of pizza dough. The pizza dough with Prt(+) strains showed an increase in viscous properties during the fermentation as compared with the Prt(-) dough. Moreover, an increase in the firmness of the crumb was observed in Prt(+) baked pizza dough.

Stabilization and prolonged reactivity of aqueous-phase ozone with cyclodextrin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dettmer, Adam; Ball, Raymond; Boving, Thomas B.

Recalcitrant organic groundwater contaminants, such as 1,4-dioxane, may require strong oxidants for complete mineralization. However, their efficacy for in-situ chemical oxidation (ISCO) is limited by oxidant decay and reactivity. Hydroxypropyl-β-cyclodextrin (HPβCD) was examined for its ability to stabilize aqueous-phase ozone (O3) and prolong oxidation potential through inclusion complex formation. Partial transformation of HPβCD by O3 was observed. However, HPβCD proved to be sufficiently recalcitrant, because it was only partially degraded in the presence of O3. The formation of a HPβCD:O3 clathrate complex was observed, which stabilized decay of O3. The presence of HPβCD increased the O3 half-life linearly with increasingmore » HPβCD:O3 molar ratio. The O3 half-life in solutions increased by as much as 40-fold relative to HPβCD-free O3 solutions. Observed O3 release from HPβCD and indigo oxidation confirmed that the formation of the inclusion complex is reversible. This proof-of-concept study demonstrates that HPβCD can complex O3 while preserving its reactivity. These results suggest that the use of clathrate stabilizers, such as HPβCD, can support the development of a facilitated-transport enabled ISCO for the O3treatment of groundwater contaminated with recalcitrant compounds.« less

KM-34, a Novel Antioxidant Compound, Protects against 6-Hydroxydopamine-Induced Mitochondrial Damage and Neurotoxicity.

PubMed

Fonseca-Fonseca, Luis Arturo; Nuñez-Figueredo, Yanier; Sánchez, Jeney Ramírez; Guerra, Maylin Wong; Ochoa-Rodríguez, Estael; Verdecia-Reyes, Yamila; Hernádez, René Delgado; Menezes-Filho, Noelio J; Costa, Teresa Cristina Silva; de Santana, Wagno Alcântara; Oliveira, Joana L; Segura-Aguilar, Juan; da Silva, Victor Diogenes Amaral; Costa, Silva Lima

2018-01-02

The etiology of Parkinson's disease is not completely understood and is believed to be multifactorial. Neuronal disorders associated to oxidative stress and mitochondrial dysfunction are widely considered major consequences. The aim of this study was to investigate the effect of the synthetic arylidenmalonate derivative 5-(3,4-dihydroxybenzylidene)-2,2-dimethyl-1,3-dioxane-4,6-dione (KM-34), in oxidative stress and mitochondrial dysfunction induced by 6-hydroxydopamine (6-OHDA). Pretreatment (2 h) with KM-34 (1 and 10 μM) markedly attenuated 6-OHDA-induced PC12 cell death in a concentration-dependent manner. KM-34 also inhibited H 2 O 2 generation, mitochondrial swelling, and membrane potential dissipation after 6-OHDA-induced mitochondrial damage. In vivo, KM-34 treatment (1 and 2 mg/Kg) reduced percentage of asymmetry (cylinder test) and increased the vertical exploration (open field) with respect to untreated injured animals; KM-34 also reduced glial fibrillary acidic protein overexpression and increased tyrosine hydroxylase-positive cell number, both in substantia nigra pars compacta. These results demonstrate that KM-34 present biological effects associated to mitoprotection and neuroprotection in vitro, moreover, glial response and neuroprotection in SNpc in vivo. We suggest that KM-34 could be a putative neuroprotective agent for inhibiting the progressive neurodegenerative disease associated to oxidative stress and mitochondrial dysfunction.

Palladium-Catalyzed Coupling of Ammonia with Aryl Chlorides, Bromides, Iodides and Sulfonates: A General Method for the Preparation of Primary Arylamines

PubMed Central

Vo, Giang D.

2010-01-01

We report that the complex generated from Pd[P(o-tol)3]2 and the alkylbisphosphine CyPF-t-Bu is a highly active and selective catalyst for the coupling of ammonia with aryl chlorides, bromides, iodides, and sulfonates. The couplings of ammonia with this catalyst conducted with a solution of ammonia in dioxane form primary arylamines from a variety of aryl electrophiles in high yields. Catalyst loadings as low as 0.1 mol % were sufficient for reactions of many aryl chlorides and bromides. In the presence of this catalyst, aryl sulfonates also coupled with ammonia for the first time in high yields. A comparison of reactions in the presence of this catalyst versus those in the presence of existing copper and palladium systems revealed a complementary, if not broader substrate scope. The utility of this method to generate amides, imides and carbamates is illustrated by a one-pot synthesis of a small library of these carbonyl compounds from aryl bromides and chlorides. Mechanistic studies show that Pd[P(o-tol)3]2 and CyPF-t-Bu generate a more active and general catalyst than that generated from CyPF-t-Bu and palladiun(II) precursors because of the low concentration of active catalyst that is generated from the combination of palladium(II), ammonia and base. PMID:19591470

Use of lignin extracted from different plant sources as standards in the spectrophotometric acetyl bromide lignin method.

PubMed

Fukushima, Romualdo S; Kerley, Monty S

2011-04-27

A nongravimetric acetyl bromide lignin (ABL) method was evaluated to quantify lignin concentration in a variety of plant materials. The traditional approach to lignin quantification required extraction of lignin with acidic dioxane and its isolation from each plant sample to construct a standard curve via spectrophotometric analysis. Lignin concentration was then measured in pre-extracted plant cell walls. However, this presented a methodological complexity because extraction and isolation procedures are lengthy and tedious, particularly if there are many samples involved. This work was targeted to simplify lignin quantification. Our hypothesis was that any lignin, regardless of its botanical origin, could be used to construct a standard curve for the purpose of determining lignin concentration in a variety of plants. To test our hypothesis, lignins were isolated from a range of diverse plants and, along with three commercial lignins, standard curves were built and compared among them. Slopes and intercepts derived from these standard curves were close enough to allow utilization of a mean extinction coefficient in the regression equation to estimate lignin concentration in any plant, independent of its botanical origin. Lignin quantification by use of a common regression equation obviates the steps of lignin extraction, isolation, and standard curve construction, which substantially expedites the ABL method. Acetyl bromide lignin method is a fast, convenient analytical procedure that may routinely be used to quantify lignin.

Eco-friendly Synthesis of Organics and Nanomaterials ...

EPA Pesticide Factsheets

The presentation summarizes our recent activity in chemical synthesis involving benign alternatives, such as the use of supported reagents, and greener reaction medium in aqueous or solvent-free conditions.1 The synthesis of heterocyclic compounds, coupling reactions, and a variety of name reactions2 are the primary beneficiaries as exemplified by the synthesis of N-aryl azacycloalkanes, isoindoles, and dihydropyrazoles, 1,3,4-oxadiazoles, 1,3,4-thiadiazoles, 1,3-dioxanes, pyrazoles, catalyzed by basic water or polystyrene sulfonic acid (PSSA) in conjunction with microwave (MW) irradiation.2 Vitamins B1, B2, C, and tea and wine polyphenols which function both as reducing and capping agents, provide extremely simple, one-pot, green synthetic methods to bulk quantities of nanomaterials in water.3a Shape-controlled synthesis of noble nanostructures via MW-assisted spontaneous reduction of noble metal salts using sugars will be presented.3b A general method has been developed for the cross-linking reaction of poly (vinyl alcohol) (PVA) with metallic systems; bimetallic systems,3c and SWNT, MWNT, and C-60.3d The strategy is extended to the formation of biodegradable carboxymethylcellulose (CMC) composite films with noble nanometals;3e such metal decoration and alignment of carbon nanotubes in CMC is possible using MW approach3f which also enables the shape-controlled bulk synthesis of Ag and Fe nanorods in poly (ethylene glycol).3g MW hydrothermal process delivers m

Spectrophotometric Determination of Mycophenolate Mofetil as Its Charge-Transfer Complexes with Two π-Acceptors

PubMed Central

Vinay, K. B.; Revanasiddappa, H. D.; Raghu, M. S.; Abdulrahman, Sameer. A. M.; Rajendraprasad, N.

2012-01-01

Two simple, selective, and rapid spectrophotometric methods are described for the determination of mycophenolate mofetil (MPM) in pure form and in tablets. Both methods are based on charge-transfer complexation reaction of MPM with p-chloranilic acid (p-CA) or 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ) in dioxane-acetonitrile medium resulting in coloured product measurable at 520 nm (p-CA) or 580 nm (DDQ). Beer's law is obeyed over the concentration ranges of 40–400 and 12–120 μg mL−1 MPM for p-CA and DDQ, respectively, with correlation coefficients (r) of 0.9995 and 0.9947. The apparent molar absorptivity values are calculated to be 1.06 × 103 and 3.87 × 103 L mol−1 cm−1, respectively, and the corresponding Sandell's sensitivities are 0.4106 and 0.1119 μg cm−1. The limits of detection (LOD) and quantification (LOQ) are also reported for both methods. The described methods were successfully applied to the determination of MPM in tablets. Statistical comparison of the results with those of the reference method showed excellent agreement. No interference was observed from the common excipients present in tablets. Both methods were validated statistically for accuracy and precision. The accuracy and reliability of the methods were further ascertained by recovery studies via standard addition procedure. PMID:22567572

HPTLC and magnetochromatography of new complexes of carboxylates with transition metals or rare earth elements and their ligands - study of lipophilicity.

PubMed

Malinowska, Irena; Wronka, Agnieszka; Ferenc, Wiesława

2017-05-01

Nineteen new complexes of carboxylates with transition and rare elements as central ions and their ligands were characterized by chromatographic analyses. The parameter of relative lipophilicity (R M0 ) of the tested compounds was determined experimentally by the reversed-phase high-performance thin layer chromatography method with mixtures of various organic modifiers (acetonitrile, acetone, dioxane) and water as a mobile phase. The extrapolated R M0 values were compared with the logP values calculated from the molecular structures of tested solutes. Similarities between the lipophilicity indices were analysed by principal component analysis and linear regression. Thin-layer chromatography combined with a magnetic field has been proposed as a complementary method for determination of lipophilicity of the investigated compounds. The chromatograms in the field and outside it were developed simultaneously in two identical chromatographic chambers. One of them was placed in the external magnetic field of 0.4 T inductivity. We proved that chelation causes a drastic change in compound lipophilicity, but all complexes did not exhibit enhanced activity as compared with the parent ligand. Also in the magnetic field the retention of some complexes changed, which means that the presence of the field influences the physicochemical properties of the compounds and their interactions with the stationary phase. Copyright © 2016 John Wiley & Sons, Ltd.

Effects of polar and nonpolar groups on the solubility of organic compounds in soil organic matter

USGS Publications Warehouse

Chiou, C.T.; Kile, D.E.

1994-01-01

Vapor sorption capacities on a high-organic-content peat, a model for soil organic matter (SOM), were determined at room temperature for the following liquids: n-hexane, 1,4-dioxane, nitroethane, acetone, acetonitrile, 1-propanol, ethanol, and methanol. The linear organic vapor sorption is in keeping with the dominance of vapor partition in peat SOM. These data and similar results of carbon tetrachloride (CT), trichloroethylene (TCE), benzene, ethylene glycol monoethyl ether (EGME), and water on the same peat from earlier studies are used to evaluate the effect of polarity on the vapor partition in SOM. The extrapolated liquid solubility from the vapor isotherm increases sharply from 3-6 wt % for low-polarity liquids (hexane, CT, and benzene) to 62 wt % for polar methanol and correlates positively with the liquid's component solubility parameters for polar interaction (??P) and hydrogen bonding (??h). The same polarity effect may be expected to influence the relative solubilities of a variety of contaminants in SOM and, therefore, the relative deviations between the SOM-water partition coefficients (Kom) and corresponding octanol-water partition coefficients (Kow) for different classes of compounds. The large solubility disparity in SOM between polar and nonpolar solutes suggests that the accurate prediction of Kom from Kow or Sw (solute water solubility) would be limited to compounds of similar polarity.

Study on the decomposition mechanism of alkyl carbonate on lithium metal by pyrolysis-gas chromatography-mass spectroscopy

NASA Astrophysics Data System (ADS)

Mogi, Ryo; Inaba, Minoru; Iriyama, Yasutoshi; Abe, Takeshi; Ogumi, Zempachi

The surface films formed on deposited lithium in electrolyte solutions based on ethylene carbonate (EC), diethyl carbonate (DEC), and dimethyl carbonate (DMC) were analyzed by pyrolysis-gas chromatography-mass spectroscopy (Py-GC-MS). In 1 M LiClO 4/EC, the main component of the surface film was easily hydrolyzed to give ethylene glycol after exposure to air, and hence was considered to have a chemical structure of ROCH 2CH 2OR', of which OR and OR' are OLi or OCO 2Li. Ethylene oxide, acetaldehyde, and 1,4-dioxane were detected in decomposition products, and they were considered to have been formed by pyrolysis of ROCH 2CH 2OR' in the pyrolyzer. The presence of ethanol in decomposition products confirmed that ring cleavage at the CH 2O bonds of EC occurs by one electron reduction. In addition, the presence of methanol implied the cleavage of the CC bond of EC upon reduction. From the surface films formed in 1 M LiClO 4/DEC and /DMC, ethanol and methanol, respectively, were detected, which suggested that corresponding lithium alkoxides and/or lithium alkyl carbonates were the main components. In 1 M LiClO 4/EC+DEC (1:1), EC dominantly decomposed to form the surface film. The surface film formed in 1 M LiPF 6/EC+DEC (1:1) contained a much smaller amount of organic compounds.

Structural and Functional Analysis of Two New Positive Allosteric Modulators of GluA2 Desensitization and Deactivation

PubMed Central

Timm, David E.; Benveniste, Morris; Weeks, Autumn M.; Nisenbaum, Eric S.

2011-01-01

At the dimer interface of the extracellular ligand-binding domain of α-amino-3-hydroxy-5-methylisoxazole-4-propionic acid (AMPA) receptors a hydrophilic pocket is formed that is known to interact with two classes of positive allosteric modulators, represented by cyclothiazide and the ampakine 2H,3H,6aH-pyrrolidino(2,1–3′,2′)1,3-oxazino(6′,5′-5,4)benzo(e)1,4-dioxan-10-one (CX614). Here, we present structural and functional data on two new positive allosteric modulators of AMPA receptors, phenyl-1,4-bis-alkylsulfonamide (CMPDA) and phenyl-1,4-bis-carboxythiophene (CMPDB). Crystallographic data show that these compounds bind within the modulator-binding pocket and that substituents of each compound overlap with distinct moieties of cyclothiazide and CX614. The goals of the present study were to determine 1) the degree of modulation by CMPDA and CMPDB of AMPA receptor deactivation and desensitization; 2) whether these compounds are splice isoform-selective; and 3) whether predictions of mechanism of action could be inferred by comparing molecular interactions between the ligand-binding domain and each compound with those of cyclothiazide and CX614. CMPDB was found to be more isoform-selective than would be predicted from initial binding assays. It is noteworthy that these new compounds are both more potent and more effective and may be more clinically relevant than the AMPA receptor modulators described previously. PMID:21543522

Ground-State Charge-Density Distribution in a Crystal of the Luminescent ortho-Phenylenediboronic Acid Complex with 8-Hydroxyquinoline.

PubMed

Jarzembska, Katarzyna N; Kamiński, Radosław; Durka, Krzysztof; Woźniak, Krzysztof

2018-05-10

This contribution is devoted to the first electron density studies of a luminescent oxyquinolinato boron complex in the solid state. ortho-Phenylenediboronic acid mixed with 8-hydroxyquinoline in dioxane forms high-quality single crystals via slow solvent evaporation, which allows successful high resolution data collection (sin θ/λ = 1.2 Å -1 ) and charge density distribution modeling. Particular attention has been paid to the boron-oxygen fragment connecting the two parts of the complex, and to the solvent species exhibiting anharmonic thermal motion. The experiment and theory compared rather well in terms of atomic charges and volumes, except for the boron centers. Boron atoms, as expected, constitute the most electron-deficient species in the complex molecule, whereas the neighboring oxygen and carbon atoms are the most significantly negatively charged ones. This part of the molecule appears to be very much involved in the charge transfer occurring between the acid fragment and oxyquinoline moiety leading to the observed fluorescence, as supported by the time-dependent density functional theory (TDDFT) results and the generated transition density maps. TDDFT calculations indicated that p-type atomic orbitals contributing to the HOMO-1, HOMO, and LUMO play the major role in the lowest energy transitions, and enabled further comparison with the charge density features, which is discussed in details. Furthermore, the results confirmed the known fact the Q ligand character is most important for the spectroscopic properties of this class of complexes.

Fabrication and Characterization of 3D-Printed Highly-Porous 3D LiFePO4 Electrodes by Low Temperature Direct Writing Process

PubMed Central

Cheng, Xingxing; Li, Bohan; Chen, Zhangwei; Mi, Shengli; Lao, Changshi

2017-01-01

LiFePO4 (LFP) is a promising cathode material for lithium-ion batteries. In this study, low temperature direct writing (LTDW)-based 3D printing was used to fabricate three-dimensional (3D) LFP electrodes for the first time. LFP inks were deposited into a low temperature chamber and solidified to maintain the shape and mechanical integrity of the printed features. The printed LFP electrodes were then freeze-dried to remove the solvents so that highly-porous architectures in the electrodes were obtained. LFP inks capable of freezing at low temperature was developed by adding 1,4 dioxane as a freezing agent. The rheological behavior of the prepared LFP inks was measured and appropriate compositions and ratios were selected. A LTDW machine was developed to print the electrodes. The printing parameters were optimized and the printing accuracy was characterized. Results showed that LTDW can effectively maintain the shape and mechanical integrity during the printing process. The microstructure, pore size and distribution of the printed LFP electrodes was characterized. In comparison with conventional room temperature direct ink writing process, improved pore volume and porosity can be obtained using the LTDW process. The electrochemical performance of LTDW-fabricated LFP electrodes and conventional roller-coated electrodes were conducted and compared. Results showed that the porous structure that existed in the printed electrodes can greatly improve the rate performance of LFP electrodes. PMID:28796182

New Strategy for the Immobilization of Lipases on Glyoxyl-Agarose Supports: Production of Robust Biocatalysts for Natural Oil Transformation.

PubMed

Godoy, César A

2017-10-12

Immobilization on Glyoxyl-agarose support (Gx) is one of the best strategies to stabilize enzymes. However, the strategy is difficult to apply at neutral pH when most enzymes are stable and, even when possible, produces labile derivatives. This work contributes to overcoming this hurdle through a strategy that combines solid-phase amination, presence of key additives, and derivative basification. To this end, aminated industrial lipases from Candida artarctica (CAL), Thermomyces lunuginosus (TLL), and the recombinant Geobacillus thermocatenulatus (BTL2) were immobilized on Gx for the first time at neutral pH using anthranilic acid (AA) or DTT as additives (immobilization yields >70%; recovered activities 37.5-76.7%). The spectroscopic evidence suggests nucleophilic catalysis and/or adsorption as the initial lipase immobilization events. Subsequent basification drastically increases the stability of BTL2-glyoxyl derivatives under harsh conditions (t 1/2 , from 2.1-54.5 h at 70 °C; from 10.2 h-140 h in 80% dioxane). The novel BTL2-derivatives were active and selective in fish oil hydrolysis (1.0-1.8 μmol of polyunsaturated fatty acids (PUFAs) min -1 ·g -1 ) whereas the selected TLL-derivative was as active and stable in biodiesel production (fatty ethyl esters, EE) as the commercial Novozyme ® -435 after ten reaction cycles (~70% EE). Therefore, the potential of the proposed strategy in producing suitable biocatalysts for industrial processes was demonstrated.

New Strategy for the Immobilization of Lipases on Glyoxyl–Agarose Supports: Production of Robust Biocatalysts for Natural Oil Transformation

PubMed Central

2017-01-01

Immobilization on Glyoxyl–agarose support (Gx) is one of the best strategies to stabilize enzymes. However, the strategy is difficult to apply at neutral pH when most enzymes are stable and, even when possible, produces labile derivatives. This work contributes to overcoming this hurdle through a strategy that combines solid-phase amination, presence of key additives, and derivative basification. To this end, aminated industrial lipases from Candida artarctica (CAL), Thermomyces lunuginosus (TLL), and the recombinant Geobacillus thermocatenulatus (BTL2) were immobilized on Gx for the first time at neutral pH using anthranilic acid (AA) or DTT as additives (immobilization yields >70%; recovered activities 37.5–76.7%). The spectroscopic evidence suggests nucleophilic catalysis and/or adsorption as the initial lipase immobilization events. Subsequent basification drastically increases the stability of BTL2–glyoxyl derivatives under harsh conditions (t1/2, from 2.1–54.5 h at 70 °C; from 10.2 h–140 h in 80% dioxane). The novel BTL2-derivatives were active and selective in fish oil hydrolysis (1.0–1.8 μmol of polyunsaturated fatty acids (PUFAs) min−1·g−1) whereas the selected TLL-derivative was as active and stable in biodiesel production (fatty ethyl esters, EE) as the commercial Novozyme®-435 after ten reaction cycles (~70% EE). Therefore, the potential of the proposed strategy in producing suitable biocatalysts for industrial processes was demonstrated. PMID:29023423

Synthesis and characterization of maleimide-functionalized polystyrene-SiO2/TiO2 hybrid nanocomposites by sol-gel process

NASA Astrophysics Data System (ADS)

Ramesh, Sivalingam; Sivasamy, Arumugam; Kim, Joo-Hyung

2012-06-01

Maleimide-functionalized polystyrene (PSMA-SiO2/TiO2) hybrid nanocomposites were prepared by sol-gel reaction starting from tratraethoxysilane (TEOS) and titanium isopropoxide in the solution of polystyrene maleimide in 1,4-dioxane. The hybrid films were obtained by the hydrolysis and polycondensation of TEOS and titanium isopropoxide in maleimide-functionalized polystyrene solution followed by the Michael addition reaction. The transparency of polymer (PSMA-SiO2/TiO2) hybrid was prepared from polystyrene titanium isopropoxide using the γ-aminopropyltriethoxy silane as crosslinking agent by in situ sol-gel process via covalent bonding between the organic-inorganic hybrid nanocomposites. The maleimide-functionalized polystyrene was synthesized by Friedel-Crafts reaction from N-choloromethyl maleimide. The FTIR spectroscopy data conformed the occurrence of Michael addition reaction between the pendant maleimide moieties of the styrene and γ-aminopropyltriethoxysilane. The chemical structure and morphology of PSMA-SiO2/TiO2 hybrid nanocomposites were characterized by FTIR, nuclear magnetic resonance (NMR), 13 C NMR, SEM, XRD, and TEM analyses. The results also indicate that the inorganic particles are much smaller in the ternary systems than in the binary systems; the shape of the inorganic particles and compatibility for maleimide-functionalized polystrene and inorganic moieties are varied with the ratio of the inorganic moieties in the hybrids. Furthermore, TGA and DSC results indicate that the thermal stability of maleimide-functionalized polystyrene was enhanced through the incorporation of the inorganic moieties in the hybrid materials.

Compensation effect in reactions between trans-4,4'-dinitrostilbene oxide and arylsulfonic acids

NASA Astrophysics Data System (ADS)

Shpan'ko, I. V.; Sadovaya, I. V.

2016-12-01

The effect structure and temperature have on the rate and free activation energy of reactions between trans-4,4'-dinitrostilbene oxide and Y-substituted arylsulfonic acids YC6H4SO3H in a mixture of dioxane with 1,2-dichloroethane (7: 3 vol/vol) at 265, 281, and 298 K is studied. It is found that as a result of the nonadditivity of the joint effect of substituents Y and temperature on the rate of the process of oxirane ring opening, the cross reaction series exhibits isoparametric properties in the aspect of enthalpy-entropy compensation. This allows the experimental determination of an isoparametric point with respect to the constant of substituent Y (σY IP= 0.52), in which activation entropy Δ S ≠ = 0 and free activation energy Δ G ≠ do not depend on temperature (Δ G ≠ = Δ H ≠), and to conduct the transition through this point with inversion of the order of the effect temperature has on the value of Δ G ≠ as a result of reversing the sign of Δ S ≠: in the series Y (σY) = 4-OCH3 (-0.27), 4-CH3 (-0.17), H (0), 4-Cl (0.23), and 3-NO2 (0.71), the values of Δ S ≠ (J/(mol K)) are-140,-119,-85,-42, and 44, respectively. The possibility of using isoparametric points as quantitative mechanistic criteria is demonstrated.

Palladium-catalyzed coupling of ammonia with aryl chlorides, bromides, iodides, and sulfonates: a general method for the preparation of primary arylamines.

PubMed

Vo, Giang D; Hartwig, John F

2009-08-12

We report that the complex generated from Pd[P(o-tol)(3)](2) and the alkylbisphosphine CyPF-t-Bu is a highly active and selective catalyst for the coupling of ammonia with aryl chlorides, bromides, iodides, and sulfonates. The couplings of ammonia with this catalyst conducted with a solution of ammonia in dioxane form primary arylamines from a variety of aryl electrophiles in high yields. Catalyst loadings as low as 0.1 mol % were sufficient for reactions of many aryl chlorides and bromides. In the presence of this catalyst, aryl sulfonates also coupled with ammonia for the first time in high yields. A comparison of reactions in the presence of this catalyst versus those in the presence of existing copper and palladium systems revealed a complementary, if not broader, substrate scope. The utility of this method to generate amides, imides, and carbamates is illustrated by a one-pot synthesis of a small library of these carbonyl compounds from aryl bromides and chlorides, ammonia, and acid chlorides or anhydrides. Mechanistic studies show that reactions conducted with the combination of Pd[P(o-tol)(3)](2) and CyPF-t-Bu as catalyst occur with faster rates and higher yields than those conducted with CyPF-t-Bu and palladiun(II) as catalyst precursors because of the low concentration of active catalyst that is generated from the combination of palladium(II), ammonia, and base.

A novel technique for producing antibody-coated microprobes using a thiol-terminal silane and a heterobifunctional crosslinker.

PubMed

Routh, V H; Helke, C J

1997-02-01

Antibody-coated microprobes are used to measure neuropeptide release in the central nervous system. Although they are not quantitative, they provide the most precise spatial resolution of the location of in vivo release of any currently available method. Previous methods of coating antibody microprobes are difficult and time-consuming. Moreover, using these methods we were unable to produce evenly coated antibody microprobes. This paper describes a novel method for the production of antibody microprobes using thiol-terminal silanes and the heterobifunctional crosslinker, 4-(4-N-maleimidophenyl)butyric acid hydrazide HCl 1/2 dioxane (MPBH). Following silation, glass micropipettes are incubated with antibody to substance P (SP) that has been conjugated to MPBH. This method results in a dense, even coating of antibody without decreasing the biological activity of the antibody. Additionally, this method takes considerably less time than previously described methods without sacrificing the use of antibody microprobes as micropipettes. The sensitivity of the microprobes for SP is in the picomolar range, and there is a linear correlation between the log of SP concentration (M) and B/B0 (r2 = 0.98). The microprobes are stable for up to 3 weeks when stored in 0.1 M sodium phosphate buffer with 50 mM NaCl (pH 7.4) at 5 degrees C. Finally, insertion into the exposed spinal cord of an anesthetized rat for 15 min produces no damage to the antibody coating.

Testing the nature of reaction coordinate describing interaction of H2 with carbonyl carbon, activated by Lewis acid complexation, and the Lewis basic solvent: A Born-Oppenheimer molecular dynamics study with explicit solvent

NASA Astrophysics Data System (ADS)

Heshmat, Mojgan; Privalov, Timofei

2017-09-01

Using Born-Oppenheimer molecular dynamics (BOMD), we explore the nature of interactions between H2 and the activated carbonyl carbon, C(carbonyl), of the acetone-B(C6F5)3 adduct surrounded by an explicit solvent (1,4-dioxane). BOMD simulations at finite (non-zero) temperature with an explicit solvent produced long-lasting instances of significant vibrational perturbation of the H—H bond and H2-polarization at C(carbonyl). As far as the characteristics of H2 are concerned, the dynamical transient state approximates the transition-state of the heterolytic H2-cleavage. The culprit is the concerted interactions of H2 with C(carbonyl) and a number of Lewis basic solvent molecules—i.e., the concerted C(carbonyl)⋯H2⋯solvent interactions. On one hand, the results presented herein complement the mechanistic insight gained from our recent transition-state calculations, reported separately from this article. But on the other hand, we now indicate that an idea of the sufficiency of just one simple reaction coordinate in solution-phase reactions can be too simplistic and misleading. This article goes in the footsteps of the rapidly strengthening approach of investigating molecular interactions in large molecular systems via "computational experimentation" employing, primarily, ab initio molecular dynamics describing reactants-interaction without constraints of the preordained reaction coordinate and/or foreknowledge of the sampling order parameters.

Fabrication and Characterization of 3D-Printed Highly-Porous 3D LiFePO₄ Electrodes by Low Temperature Direct Writing Process.

PubMed

Liu, Changyong; Cheng, Xingxing; Li, Bohan; Chen, Zhangwei; Mi, Shengli; Lao, Changshi

2017-08-10

LiFePO₄ (LFP) is a promising cathode material for lithium-ion batteries. In this study, low temperature direct writing (LTDW)-based 3D printing was used to fabricate three-dimensional (3D) LFP electrodes for the first time. LFP inks were deposited into a low temperature chamber and solidified to maintain the shape and mechanical integrity of the printed features. The printed LFP electrodes were then freeze-dried to remove the solvents so that highly-porous architectures in the electrodes were obtained. LFP inks capable of freezing at low temperature was developed by adding 1,4 dioxane as a freezing agent. The rheological behavior of the prepared LFP inks was measured and appropriate compositions and ratios were selected. A LTDW machine was developed to print the electrodes. The printing parameters were optimized and the printing accuracy was characterized. Results showed that LTDW can effectively maintain the shape and mechanical integrity during the printing process. The microstructure, pore size and distribution of the printed LFP electrodes was characterized. In comparison with conventional room temperature direct ink writing process, improved pore volume and porosity can be obtained using the LTDW process. The electrochemical performance of LTDW-fabricated LFP electrodes and conventional roller-coated electrodes were conducted and compared. Results showed that the porous structure that existed in the printed electrodes can greatly improve the rate performance of LFP electrodes.

Biodegradable copolymers carrying cell-adhesion peptide sequences.

PubMed

Proks, Vladimír; Machová, Lud'ka; Popelka, Stepán; Rypácek, Frantisek

2003-01-01

Amphiphilic block copolymers are used to create bioactive surfaces on biodegradable polymer scaffolds for tissue engineering. Cell-selective biomaterials can be prepared using copolymers containing peptide sequences derived from extracellular-matrix proteins (ECM). Here we discuss alternative ways for preparation of amphiphilic block copolymers composed of hydrophobic polylactide (PLA) and hydrophilic poly(ethylene oxide) (PEO) blocks with cell-adhesion peptide sequences. Copolymers PLA-b-PEO were prepared by a living polymerisation of lactide in dioxane with tin(II)2-ethylhexanoate as a catalyst. The following approaches for incorporation of peptides into copolymers were elaborated. (a) First, a side-chain protected Gly-Arg-Gly-Asp-Ser-Gly (GRGDSG) peptide was prepared by solid-phase peptide synthesis (SPPS) and then coupled with delta-hydroxy-Z-amino-PEO in solution. In the second step, the PLA block was grafted to it via a controlled polymerisation of lactide initiated by the hydroxy end-groups of PEO in the side-chain-protected GRGDSG-PEO. Deprotection of the peptide yielded a GRGDSG-b-PEO-b-PLA copolymer, with the peptide attached through its C-end. (b) A protected GRGDSG peptide was built up on a polymer resin and coupled with Z-carboxy-PEO using a solid-phase approach. After cleavage of the delta-hydroxy-PEO-GRGDSG copolymer from the resin, polymerisation of lactide followed by deprotection of the peptide yielded a PLA-b-PEO-b-GRGDSG block copolymer, in which the peptide is linked through its N-terminus.

The fate of organic micropollutants during long-term/long-distance river bank filtration.

PubMed

Hamann, Enrico; Stuyfzand, Pieter J; Greskowiak, Janek; Timmer, Harrie; Massmann, Gudrun

2016-03-01

The fate of organic micropollutants during long-term/long-distance river bank filtration (RBF) at a temporal scale of several years was investigated along a row of monitoring wells perpendicular to the Lek River (the Netherlands). Out of 247 compounds, which were irregularly analyzed in the period 1999-2013, only 15 were detected in both the river and river bank observation wells. Out of these, 10 compounds (1,4-dioxan, 1,5-naphthalene disulfonate (1,5-NDS), 2-amino-1,5-NDS, 3-amino-1,5-NDS, AOX, carbamazepine, EDTA, MTBE, toluene and triphenylphosphine oxide) showed fully persistent behavior (showing no concentration decrease at all), even after 3.6 years transit time. The remaining 5 compounds (1,3,5-naphthalene trisulfonate (1,3,5-NTS), 1,3,6-NTS, diglyme, iopamidol, triglyme) were partially removed. Their reactive transport parameters (removal rate constants/half-lives, retardation coefficients) were inferred from numerical modeling. In addition, maximum half-lives for 14 of the fully removed compounds, for which the data availability was sufficient to deduce 100% removal during sub-surface passage, were approximated based on travel times to the nearest well. The study is one of very few reporting on the long-term field-scale behavior of organic micropollutants. It highlights the efficiency of RBF for water quality improvement as a pre-treatment step for drinking water production. However, it also shows the very persistent behavior of various compounds in groundwater. Copyright © 2015 Elsevier B.V. All rights reserved.

Study on four polymorphs of bifendate based on X-ray crystallography.

PubMed

Nie, Jinju; Yang, Dezhi; Hu, Kun; Lu, Yang

2016-05-01

Bifendate, a synthetic anti-hepatitis drug, exhibits polycrystalline mode phenomena with 2 polymorphs reported (forms A and B). Single crystals of the known crystalline form B and 3 new crystallosolvates involving bifendate solvated with tetrahydrofuran (C), dioxane (D), and pyridine (E) in a stoichiometric ratio of 1:1 were obtained and characterized by X-ray crystallography, thermal analysis, and Fourier transform infrared (FT-IR) spectroscopy. The differences in molecular conformation, intermolecular interaction and crystal packing arrangement for the four polymorphs were determined and the basis for the polymorphisms was investigated. The rotation of single bonds resulted in different orientations for the biphenyl, methyl ester and methoxyl groups. All guest solvent molecules interacted with the host molecule via an interesting intercalative mode along the [1 0 0] direction in the channel formed by the host molecules through weak aromatic stacking interactions or non-classical hydrogen bonds, of which the volume and planarity played an important role in the intercalation of the host with the guest. The incorporation of solvent-augmented rotation of the C-C bond of the biphenyl group had a striking effect on the host molecular conformation and contributed to the formation of bifendate polymorphs. Moreover, the simulated powder X-ray diffraction (PXRD) patterns for each form were calculated on the basis of the single-crystal data and proved to be unique. The single-crystal structures of the four crystalline forms are reported in this paper.

Conformational analysis of a polyconjugated protein-binding ligand by joint quantum chemistry and polarizable molecular mechanics. Addressing the issues of anisotropy, conjugation, polarization, and multipole transferability.

PubMed

Goldwaser, Elodie; de Courcy, Benoit; Demange, Luc; Garbay, Christiane; Raynaud, Françoise; Hadj-Slimane, Reda; Piquemal, Jean-Philip; Gresh, Nohad

2014-11-01

We investigate the conformational properties of a potent inhibitor of neuropilin-1, a protein involved in cancer processes and macular degeneration. This inhibitor consists of four aromatic/conjugated fragments: a benzimidazole, a methylbenzene, a carboxythiourea, and a benzene-linker dioxane, and these fragments are all linked together by conjugated bonds. The calculations use the SIBFA polarizable molecular mechanics procedure. Prior to docking simulations, it is essential to ensure that variations in the ligand conformational energy upon rotations around its six main-chain torsional bonds are correctly represented (as compared to high-level ab initio quantum chemistry, QC). This is done in two successive calibration stages and one validation stage. In the latter, the minima identified following independent stepwise variations of each of the six main-chain torsion angles are used as starting points for energy minimization of all the torsion angles simultaneously. Single-point QC calculations of the minimized structures are then done to compare their relative energies ΔE conf to the SIBFA ones. We compare three different methods of deriving the multipoles and polarizabilities of the central, most critical moiety of the inhibitor: carboxythiourea (CTU). The representation that gives the best agreement with QC is the one that includes the effects of the mutual polarization energy E pol between the amide and thioamide moieties. This again highlights the critical role of this contribution. The implications and perspectives of these findings are discussed.

Exploratory studies on some electrochemical cell systems

NASA Astrophysics Data System (ADS)

Chaudhuri, Srikumar; Guha, D.

Exploratory studies were conducted on cell systems with different metal anodes, and iodine and sulphur mixed with graphite powder in a polymer matrix as cathodes, using different electrolytes in non-aqueous and aqueous media as ionic charge carriers. The electrical conductance of the electrolyte solutions in aqueous and non-aqueous solvents, the open circuit voltage (OCV) and short circuit current (SCC) for the different cell systems were measured. To date, the non-aqueous solvents used in our studies were dimethylformamide, formamide, dioxan, and nitrobenzene, and the electrolytes used were potassium iodide, caustic potash, cetyltrimethylammonium bromide (CTAB), sodium lauryl sulphate (SLS) and calcium chloride. These electrolytes were used in both non-aqueous and aqueous media. In general, aqueous electrolyte solutions gave a better performance than non-aqueous electrolyte solutions. Of the aqueous electrolytes, the highest conductance was shown by potassium chloride solution in water (conductance=0.0334 mho). However, the best OCV and SCC were shown by aluminium as anode and iodine as cathode with a saturated solution of caustic potash in water. The OCV was 1.85 V and the SCC was 290 mA cm -2. The highest conductance among the non-aqueous systems was shown by caustic potash in formamide. (Conductance=0.013 mho.) The best OCV and SCC, however, were shown by a zinc anode and iodine cathode with saturated potassium chloride in formamide, having an OCV of 1.55 V and an SCC of 150 mA cm -2. Further studies are in progress to obtain detailed performance data and recharging characteristics of some of the more promising systems reported here.

[Application of predictive model to estimate concentrations of chemical substances in the work environment].

PubMed

Kupczewska-Dobecka, Małgorzata; Czerczak, Sławomir; Jakubowski, Marek; Maciaszek, Piotr; Janasik, Beata

2010-01-01

Based on the Estimation and Assessment of Substance Exposure (EASE) predictive model implemented into the European Union System for the Evaluation of Substances (EUSES 2.1.), the exposure to three chosen organic solvents: toluene, ethyl acetate and acetone was estimated and compared with the results of measurements in workplaces. Prior to validation, the EASE model was pretested using three exposure scenarios. The scenarios differed in the decision tree of pattern of use. Five substances were chosen for the test: 1,4-dioxane tert-methyl-butyl ether, diethylamine, 1,1,1-trichloroethane and bisphenol A. After testing the EASE model, the next step was the validation by estimating the exposure level and comparing it with the results of measurements in the workplace. We used the results of measurements of toluene, ethyl acetate and acetone concentrations in the work environment of a paint and lacquer factory, a shoe factory and a refinery. Three types of exposure scenarios, adaptable to the description of working conditions were chosen to estimate inhalation exposure. Comparison of calculated exposure to toluene, ethyl acetate and acetone with measurements in workplaces showed that model predictions are comparable with the measurement results. Only for low concentration ranges, the measured concentrations were higher than those predicted. EASE is a clear, consistent system, which can be successfully used as an additional component of inhalation exposure estimation. If the measurement data are available, they should be preferred to values estimated from models. In addition to inhalation exposure estimation, the EASE model makes it possible not only to assess exposure-related risk but also to predict workers' dermal exposure.

Port wine oxidation management: a multiparametric kinetic approach.

PubMed

Martins, Rui Costa; Monforte, Ana Rita; Silva Ferreira, António

2013-06-05

Port wine is a flagship fortified wine of Portugal, which undergoes a particularly long aging period, developing a dynamic sensory profile over time, responsible for several wine categories, which is dependent upon the type of aging (bottle or barrel). Therefore, the quality of the product is dependent upon the chemical mechanisms occurring during the aging process, such as oxidation or Maillard reactions. To attain the desired quality management, it is necessary to understand how technological parameters, such as temperature or oxygen exposure, affect the kinetics of the formation of key odorants, such as sotolon. There is a lack of information about the impact of the storage conditions (oxygen and temperature) on Port wine quality. In this study, the effect of these two parameters were investigated to increase the knowledge database concerning aging management of Port wines. It was found that sotolon formation is highly dependent upon oxygen and temperature. There is however a synergistic effect between these two parameters that could significantly increase the concentration. The kinetic parameters of oxygen, sotolon, and other compounds related to Port aging (cis- and trans-5-hydroxy-2-methyl-1,3-dioxan, 2-furfural, 5-hydroxy-methyl-furfural, and 5-methyl-furfural) are also reported. Kinetic models with Monte Carlo simulations, where the oxygen permeability dispersion and temperature are the parameters under evaluation, were applied. On the basis of the modeling predictions, it would seem that the temperature of a cellar would have a more significant impact on the Port wines stored in containers where the oxygen intake is higher (barrels) when compared to containers with low oxygen permeability (bottles using cork stoppers).

Changes in the classification of carcinogenic chemicals in the work area. Section III of the German List of MAK and BAT Values.

PubMed

Neumann, H G; Vamvakas, S; Thielmann, H W; Gelbke, H P; Filser, J G; Reuter, U; Greim, H; Kappus, H; Norpoth, K H; Wardenbach, P; Wichmann, H E

1998-11-01

Carcinogenic chemicals in the work area are currently classified into three categories in section III of the German List of MAK and BAT Values (list of values on maximum workplace concentrations and biological tolerance for occupational exposures). This classification is based on qualitative criteria and reflects essentially the weight of evidence available for judging the carcinogenic potential of the chemicals. It is proposed that these categories - IIIA1, IIIA2, IIIB - be retained as Categories 1, 2, and 3, to correspond with European Union regulations. On the basis of our advancing knowledge of reaction mechanisms and the potency of carcinogens, these three categories are supplemented with two additional categories. The essential feature of substances classified in the new categories is that exposure to these chemicals does not contribute significantly to risk of cancer to man, provided that an appropriate exposure limit (MAK value) is observed. Chemicals known to act typically by nongenotoxic mechanisms and for which information is available that allows evaluation of the effects of low-dose exposures, are classified in Category 4. Genotoxic chemicals for which low carcinogenic potency can be expected on the basis of dose-response relationships and toxicokinetics, and for which risk at low doses can be assessed are classified in Category 5. The basis for a better differentiation of carcinogens is discussed, the new categories are defined, and possible criteria for classification are described. Examples for Category 4 (1,4-dioxane) and Category 5 (styrene) are presented.

Proposed changes in the classification of carcinogenic chemicals in the work area.

PubMed

Neumann, H G; Thielmann, H W; Filser, J G; Gelbke, H P; Greim, H; Kappus, H; Norpoth, K H; Reuter, U; Vamvakas, S; Wardenbach, P; Wichmann, H E

1997-12-01

Carcinogenic chemicals in the work area are currently classified into three categories in Section III of the German List of MAK and BAT Values. This classification is based on qualitative criteria and reflects essentially the weight of evidence available for judging the carcinogenic potential of the chemicals. It is proposed that these Categories--IIIA1, IIIA2, and IIIB--be retained as Categories 1, 2, and 3, to conform with EU regulations. On the basis of our advancing knowledge of reaction mechanisms and the potency of carcinogens, it is now proposed that these three categories be supplemented with two additional categories. The essential feature of substances classified in the new categories is that exposure to these chemicals does not convey a significant risk of cancer to man, provided that an appropriate exposure limit (MAK value) is observed. It is proposed that chemicals known to act typically by nongenotoxic mechanisms and for which information is available that allows evaluation of the effects of low-dose exposures be classified in Category 4. Genotoxic chemicals for which low carcinogenic potency can be expected on the basis of dose-response relationships and toxicokinetics and for which risk at low doses can be assessed will be classified in Category 5. The basis for a better differentiation of carcinogens is discussed, the new categories are defined, and possible criteria for classification are described. Examples for Category 4 (1,4-dioxane) and Category 5 (styrene) are presented. The proposed changes in classifying carcinogenic chemicals in the work area are presented for further discussion.

Changes in the classification of carcinogenic chemicals in the work area. (Section III of the German List of MAK and BAT values).

PubMed

Neumann, H G; Thielmann, H W; Filser, J G; Gelbke, H P; Greim, H; Kappus, H; Norpoth, K H; Reuter, U; Vamvakas, S; Wardenbach, P; Wichmann, H E

1998-01-01

Carcinogenic chemicals in the work area were previously classified into three categories in section III of the German List of MAK and BAT values (the list of values on maximum workplace concentrations and biological tolerance for occupational exposures). This classification was based on qualitative criteria and reflected essentially the weight of evidence available for judging the carcinogenic potential of the chemicals. In the new classification scheme the former sections IIIA1, IIIA2, and IIIB are retained as categories 1, 2, and 3, to correspond with European Union regulations. On the basis of our advancing knowledge of reaction mechanisms and the potency of carcinogens, these three categories are supplemented with two additional categories. The essential feature of substances classified in the new categories is that exposure to these chemicals does not contribute significantly to the risk of cancer to man, provided that an appropriate exposure limit (MAK value) is observed. Chemicals known to act typically by non-genotoxic mechanisms, and for which information is available that allows evaluation of the effects of low-dose exposures, are classified in category 4. Genotoxic chemicals for which low carcinogenic potency can be expected on the basis of dose/response relationships and toxicokinetics and for which risk at low doses can be assessed are classified in category 5. The basis for a better differentiation of carcinogens is discussed, the new categories are defined, and possible criteria for classification are described. Examples for category 4 (1,4-dioxane) and category 5 (styrene) are presented.

Investigation of Different Colloidal Porous Silicon Solutions and Their Composite Solid Matrix Rods by Optical Techniques

NASA Astrophysics Data System (ADS)

Khan, M. Naziruddin; Aldalbahi, Ali; Almohammedi, Abdullah

2018-03-01

Colloidal porous silicon (PSi) in different solvents was synthesized by simple chemical etching. Colloidal solutions were then prepared using different quantities of silicon wafer pieces (Pcs) and chloroplatinic (Pt) acid in catalyst solution. The effect on the properties of the colloidal solutions and composite rods were investigated using various optical characterization techniques. Absorption and photoluminescence (PL) intensity of the colloidal PSi solutions are observed to depend on the quantity of wafer Pcs, the Pt-solution, and the porosity formation on the wafer surface. The morphological structure of the PSi in a solvent and the solid-rod environments were studied using field-emission scanning electron microscopy (FE-SEM) and were observed to have different structures. A mono-oriented structure of PSi exists in tetrahydrofuran, which has stereo orientation in dioxane and dimethylsulfoxide (approximately 5-8 nm as confirmed using high resolution transmission electron microscopy). Subsequently, some colloidal PSi solutions were directly embedded in three types of sol-gel-based matrices, silica, ormosils (or organically modified silica) and polymer, which easily generated solid rods. Spontaneous emission (SE) of the PSi solutions and their composite rods were examined using a high power picosecond 355 nm laser source. The emitted PL and SE signals of the colloidal PSi solutions were dependent on the Pt volume, nature of the solvent, quantity of Si wafer piece, and pumping energy. The response of SE signals from the PSi composites rods is an interesting phenomenon, and such nanocomposites may be used for future research on light amplification.

Tris(phosphinoamide)-supported uranium-cobalt heterobimetallic complexes featuring Co → U dative interactions.

PubMed

Napoline, J Wesley; Kraft, Steven J; Matson, Ellen M; Fanwick, Phillip E; Bart, Suzanne C; Thomas, Christine M

2013-10-21

A series of tris- and tetrakis(phosphinoamide) U/Co complexes has been synthesized. The uranium precursors, (η(2)-Ph2PN(i)Pr)4U (1), (η(2)-(i)Pr2PNMes)4U (2), (η(2)-Ph2PN(i)Pr)3UCl (3), and (η(2)-(i)Pr2PNMes)3UI (4), were easily accessed via addition of the appropriate stoichiometric equivalents of [Ph2PN(i)Pr]K or [(i)Pr2PNMes]K to UCl4 or UI4(dioxane)2. Although the phosphinoamide ligands in 1 and 4 have been shown to coordinate to U in an η(2)-fashion in the solid state, the phosphines are sufficiently labile in solution to coordinate cobalt upon addition of CoI2, generating the heterobimetallic Co/U complexes ICo(Ph2PN(i)Pr)3U[η(2)-Ph2PN(i)Pr] (5), ICo((i)Pr2PNMes)3U[η(2)-((i)Pr2PNMes)] (6), ICo(Ph2PN(i)Pr)3UI (7), and ICo((i)Pr2PNMes)3UI (8). Structural characterization of complexes 5 and 7 reveals reasonably short Co-U interatomic distances, with 7 exhibiting the shortest transition metal-uranium distance ever reported (2.874(3) Å). Complexes 7 and 8 were studied by cyclic voltammetry to examine the influence of the metal-metal interaction on the redox properties compared with both monometallic Co and heterobimetallic Co/Zr complexes. Theoretical studies are used to further elucidate the nature of the transition metal-actinide interaction.

Thermochemistry of Alane Complexes for Hydrogen Storage: A Theoretical and Experimental Investigation

PubMed Central

2011-01-01

Knowledge of the relative stabilities of alane (AlH3) complexes with electron donors is essential for identifying hydrogen storage materials for vehicular applications that can be regenerated by off-board methods; however, almost no thermodynamic data are available to make this assessment. To fill this gap, we employed the G4(MP2) method to determine heats of formation, entropies, and Gibbs free energies of formation for 38 alane complexes with NH3−nRn (R = Me, Et; n = 0−3), pyridine, pyrazine, triethylenediamine (TEDA), quinuclidine, OH2−nRn (R = Me, Et; n = 0−2), dioxane, and tetrahydrofuran (THF). Monomer, bis, and selected dimer complex geometries were considered. Using these data, we computed the thermodynamics of the key formation and dehydrogenation reactions that would occur during hydrogen delivery and alane regeneration, from which trends in complex stability were identified. These predictions were tested by synthesizing six amine−alane complexes involving trimethylamine, triethylamine, dimethylethylamine, TEDA, quinuclidine, and hexamine and obtaining upper limits of ΔG° for their formation from metallic aluminum. Combining these computational and experimental results, we establish a criterion for complex stability relevant to hydrogen storage that can be used to assess potential ligands prior to attempting synthesis of the alane complex. On the basis of this, we conclude that only a subset of the tertiary amine complexes considered and none of the ether complexes can be successfully formed by direct reaction with aluminum and regenerated in an alane-based hydrogen storage system. PMID:22962624

Cooperativity of halogen, chalcogen, and pnictogen bonds in infinite molecular chains by electronic structure theory.

PubMed

George, Janine; Deringer, Volker L; Dronskowski, Richard

2014-05-01

Halogen bonds (XBs) are intriguing noncovalent interactions that are frequently being exploited for crystal engineering. Recently, similar bonding mechanisms have been proposed for adjacent main-group elements, and noncovalent "chalcogen bonds" and "pnictogen bonds" have been identified in crystal structures. A fundamental question, largely unresolved thus far, is how XBs and related contacts interact with each other in crystals; similar to hydrogen bonding, one might expect "cooperativity" (bonds amplifying each other), but evidence has been sparse. Here, we explore the crucial step from gas-phase oligomers to truly infinite chains by means of quantum chemical computations. A periodic density functional theory (DFT) framework allows us to address polymeric chains of molecules avoiding the dreaded "cluster effects" as well as the arbitrariness of defining a "large enough" cluster. We focus on three types of molecular chains that we cut from crystal structures; furthermore, we explore reasonable substitutional variants in silico. We find evidence of cooperativity in chains of halogen cyanides and also in similar chalcogen- and pnictogen-bonded systems; the bonds, in the most extreme cases, are amplified through cooperative effects by 79% (I···N), 90% (Te···N), and 103% (Sb···N). Two experimentally known organic crystals, albeit with similar atomic connectivity and XB characteristics, show signs of cooperativity in one case but not in another. Finally, no cooperativity is observed in alternating halogen/acetone and halogen/1,4-dioxane chains; in fact, these XBs weaken each other by up to 26% compared to the respective gas-phase dimers.

Synthesis, characterization and in vitro studies of doxorubicin-loaded magnetic nanoparticles grafted to smart copolymers on A549 lung cancer cell line.

PubMed

Akbarzadeh, Abolfazl; Samiei, Mohammad; Joo, Sang Woo; Anzaby, Maryam; Hanifehpour, Younes; Nasrabadi, Hamid Tayefi; Davaran, Soodabeh

2012-12-18

The aim of present study was to develop the novel methods for chemical and physical modification of superparamagnetic iron oxide nanoparticles (SPIONs) with polymers via covalent bonding entrapment. These modified SPIONs were used for encapsulation of anticancer drug doxorubicin. At first approach silane-grafted magnetic nanoparticles was prepared and used as a template for polymerization of the N-isopropylacrylamide (NIPAAm) and methacrylic acid (MAA) via radical polymerization. This temperature/pH-sensitive copolymer was used for preparation of DOX-loaded magnetic nanocomposites. At second approach Vinyltriethoxysilane-grafted magnetic nanoparticles were used as a template to polymerize PNIPAAm-MAA in 1, 4 dioxan and methylene-bis-acrylamide (BIS) was used as a cross-linking agent. Chemical composition and magnetic properties of Dox-loaded magnetic hydrogel nanocomposites were analyzed by FT-IR, XRD, and VSM. The results demonstrate the feasibility of drug encapsulation of the magnetic nanoparticles with NIPAAm-MAA copolymer via covalent bonding. The key factors for the successful prepardtion of magnetic nanocomposites were the structure of copolymer (linear or cross-linked), concentration of copolymer and concentration of drug. The influence of pH and temperature on the release profile of doxorubicin was examined. The in vitro cytotoxicity test (MTT assay) of both magnetic DOx-loaded nanoparticles was examined. The in vitro tests showed that these systems are no toxicity and are biocompatible. IC50 of DOx-loaded Fe3O4 nanoparticles on A549 lung cancer cell line showed that systems could be useful in treatment of lung cancer.

Investigation of Different Colloidal Porous Silicon Solutions and Their Composite Solid Matrix Rods by Optical Techniques

NASA Astrophysics Data System (ADS)

Khan, M. Naziruddin; Aldalbahi, Ali; Almohammedi, Abdullah

2018-07-01

Colloidal porous silicon (PSi) in different solvents was synthesized by simple chemical etching. Colloidal solutions were then prepared using different quantities of silicon wafer pieces (Pcs) and chloroplatinic (Pt) acid in catalyst solution. The effect on the properties of the colloidal solutions and composite rods were investigated using various optical characterization techniques. Absorption and photoluminescence (PL) intensity of the colloidal PSi solutions are observed to depend on the quantity of wafer Pcs, the Pt-solution, and the porosity formation on the wafer surface. The morphological structure of the PSi in a solvent and the solid-rod environments were studied using field-emission scanning electron microscopy (FE-SEM) and were observed to have different structures. A mono-oriented structure of PSi exists in tetrahydrofuran, which has stereo orientation in dioxane and dimethylsulfoxide (approximately 5-8 nm as confirmed using high resolution transmission electron microscopy). Subsequently, some colloidal PSi solutions were directly embedded in three types of sol-gel-based matrices, silica, ormosils (or organically modified silica) and polymer, which easily generated solid rods. Spontaneous emission (SE) of the PSi solutions and their composite rods were examined using a high power picosecond 355 nm laser source. The emitted PL and SE signals of the colloidal PSi solutions were dependent on the Pt volume, nature of the solvent, quantity of Si wafer piece, and pumping energy. The response of SE signals from the PSi composites rods is an interesting phenomenon, and such nanocomposites may be used for future research on light amplification.

Surface biofunctionalization of three-dimensional porous poly(lactic acid) scaffold using chitosan/OGP coating for bone tissue engineering.

PubMed

Zeng, Sen; Ye, Jianhua; Cui, Zhixiang; Si, Junhui; Wang, Qianting; Wang, Xiaofeng; Peng, Kaiping; Chen, Wenzhe

2017-08-01

As one of the stimulators on bone formation, osteogenic growth peptide (OGP) improves both proliferation and differentiation of the bone cells in vitro and in vivo. The aim of this work was the preparation of three dimensional porous poly(lactic acid) (PLA) scaffold with high porosity from PLA-dioxane-water ternary system with the use of vacuum-assisted solvent casting, phase separation, solvent extraction and particle leaching methods. Then, by surface coating of PLA scaffold with chitosan (CS)/OGP solution, biofunctionalization of PLA scaffold had been completed for application in bone regeneration. The effects of frozen temperature (-20, -50, -80°C) and PLA solution concentration (10, 12, 14wt%) on the microstructure, water absorption, porosity, hydrophilicity, mechanical properties, and biocompatibility of PLA and CS/OGP/PLA scaffold were investigated. Results showed that both PLA and CS/OGP/PLA scaffolds have an interconnected network structure and a porosity of up to 96.1% and 91.5%, respectively. The CS/OGP/PLA scaffold exhibited better hydrophilicity and mechanical properties than that of uncoated PLA scaffold. Moreover, the results of cell culture test showed that CS/OGP coating could stimulate the proliferation and growth of osteoblast cells on CS/OGP/PLA scaffold. These finding suggested that the surface biofunctionalization by CS/OGP coating layer could be an effective method on enhancing cell adhesion to synthetic polymer-based scaffolds in tissue engineering application and the developed porous CS/OGP/PLA scaffold should be considered as alternative biomaterials for bone regeneration. Copyright © 2017 Elsevier B.V. All rights reserved.

Multiple solvent crystal structures of ribonuclease A: An assessment of the method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dechene, Michelle; Wink, Glenna; Smith, Mychal

2010-11-12

The multiple solvent crystal structures (MSCS) method uses organic solvents to map the surfaces of proteins. It identifies binding sites and allows for a more thorough examination of protein plasticity and hydration than could be achieved by a single structure. The crystal structures of bovine pancreatic ribonuclease A (RNAse A) soaked in the following organic solvents are presented: 50% dioxane, 50% dimethylformamide, 70% dimethylsulfoxide, 70% 1,6-hexanediol, 70% isopropanol, 50% R,S,R-bisfuran alcohol, 70% t-butanol, 50% trifluoroethanol, or 1.0M trimethylamine-N-oxide. This set of structures is compared with four sets of crystal structures of RNAse A from the protein data bank (PDB) andmore » with the solution NMR structure to assess the validity of previously untested assumptions associated with MSCS analysis. Plasticity from MSCS is the same as from PDB structures obtained in the same crystal form and deviates only at crystal contacts when compared to structures from a diverse set of crystal environments. Furthermore, there is a good correlation between plasticity as observed by MSCS and the dynamic regions seen by NMR. Conserved water binding sites are identified by MSCS to be those that are conserved in the sets of structures taken from the PDB. Comparison of the MSCS structures with inhibitor-bound crystal structures of RNAse A reveals that the organic solvent molecules identify key interactions made by inhibitor molecules, highlighting ligand binding hot-spots in the active site. The present work firmly establishes the relevance of information obtained by MSCS.« less

Assessment of analytical methods to determine pyrethroids content of bednets.

PubMed

Castellarnau, Marc; Ramón-Azcón, Javier; Gonzalez-Quinteiro, Yolanda; López, Jordi F; Grimalt, Joan O; Marco, María-Pilar; Nieuwenhuijsen, Mark; Picado, Albert

2017-01-01

To present and evaluate simple, cost-effective tests to determine the amount of insecticide on treated materials. We developed and evaluated a competitive immunoassay on two different platforms: a label-free impedimetric biosensor (EIS biosensor) and a lateral flow. Both approaches were validated by gas chromatography (GC) and ELISA, gold standards for analytical methods and immunoassays, respectively. Finally, commercially available pyrethroid-treated ITN samples were analysed. Different extraction methods were evaluated. Insecticide extraction by direct infusion of the ITN samples with dichloromethane and dioxane showed recovery efficiencies around 100% for insecticide-coated bednets, and >70% for insecticide-incorporated bednets. These results were comparable to those obtained with standard sonication methods. The competitive immunoassay characterisation with ELISA presented a dynamic range between 12 nm and 1.5 μm (coefficient of variation (CV) below 5%), with an IC 50 at 138 nm, and a limit of detection (LOD) of 3.2 nm. EIS biosensor had a linear range between 1.7 nm and 61 nm (CV around 14%), with an IC 50 at 10.4 nm, and a LOD of 0.6 nm. Finally, the lateral flow approach showed a dynamic range between 150 nm and 1.5 μm, an IC 50 at 505 nm and a LOD of 67 nm. ELISA can replace chromatography as an accurate laboratory technique to determine insecticide concentration in bednets. The lateral flow approach developed can be used to estimate ITN insecticide concentration in the field. This new technology, coupled to the new extraction methods, should provide reliable guidelines for ITN use and replacement in the field. © 2016 John Wiley & Sons Ltd.

A versatile tripodal amide receptor for the encapsulation of anions or hydrated anions via formation of dimeric capsules.

PubMed

Arunachalam, M; Ghosh, Pradyut

2010-02-01

A bowl-shaped tripodal receptor with an appropriately positioned amide functionality on the benzene platform and electron-withdrawing p-nitrophenyl terminals (L(1)) has been designed, synthesized, and studied for the anion binding properties. The single-crystal X-ray crystallographic analysis on crystals of L(1) with tetrabutylammonium salts of nitrate (1), acetate (2), fluoride (3), and chloride (4) obtained in moist dioxane medium showed encapsulation of two NO(3)(-), [(AcO)(2)(H(2)O)(4)](2-), [F(2)(H(2)O)(6)](2-), and [Cl(2)(H(2)O)(4)](2-) respectively as the anionic guests inside the staggered dimeric capsular assembly of L(1). The p-nitro substitution in the aryl terminals assisted the formation of dimeric capsular assembly of L(1) exclusively upon binding/encapsulating above different guests. Though L(1) demonstrates capsule formation upon anion or hydrated anion complexation for all of the anions studied here, its positional isomer with the o-nitro-substituted tripodal triamide receptor L(2) selectively formed the dimeric capsular assembly upon encapsulation of [F(2)(H(2)O)(6)](2-) and noncapsular aggregates in the cases of other anions such as Cl(-), NO(3)(-), and AcO(-). Interestingly, structural investigations upon anion exchange of the complexes revealed that both isomers have selectivity toward the formation of a [F(2)(H(2)O)(6)](2-) encapsulated dimeric capsule. In contrast, solution-state (1)H NMR titration studies of L(1) and L(2) in DMSO-d(6) with AcO(-) indicated 1:3 (host:guest) binding.

Development and validation of a stability-indicating RP-HPLC method for assay of betamethasone and estimation of its related compounds.

PubMed

Fu, Qiang; Shou, Minshan; Chien, Dwight; Markovich, Robert; Rustum, Abu M

2010-02-05

Betamethasone (9alpha-fluoro-16beta-methylprednisolone) is one of the members of the corticosteriod family of active pharmaceutical ingredient (API), which is widely used as an anti-inflammatory agent and also as a starting material to manufacture various esters of betamethasone. A stability-indicating reverse-phase high performance liquid chromatography (RP-HPLC) method has been developed and validated which can separate and accurately quantitate low levels of 26 betamethasone related compounds. The stability-indicating capability of the method was demonstrated through adequate separation of all potential betamethasone related compounds from betamethasone and also from each other that are present in aged and stress degraded betamethasone stability samples. Chromatographic separation of betamethasone and its related compounds was achieved by using a gradient elution at a flow rate of 1.0mL/min on a ACE 3 C18 column (150mmx4.6mm, 3microm particle size, 100A pore size) at 40 degrees C. Mobile phase A of the gradient was 0.1% methanesulfonic acid in aqueous solution and mobile phase B was a mixture of tert-butanol and 1,4-dioxane (7:93, v/v). UV detection at 254nm was employed to monitor the analytes. For betamethasone 21-aldehyde, the QL and DL were 0.02% and 0.01% respectively. For betamethasone and the rest of the betamethasone related compounds, the QL and DL were 0.05% and 0.02%. The precision of betamethasone assay is 0.6% and the accuracy of betamethasone assay ranged from 98.1% to 99.9%.

Amorphous solid dispersion of cyclosporine A prepared with fine droplet drying process: Physicochemical and pharmacokinetic characterization.

PubMed

Suzuki, Hiroki; Moritani, Tatsuru; Morinaga, Tadahiko; Seto, Yoshiki; Sato, Hideyuki; Onoue, Satomi

2017-03-15

The present study aimed to develop an amorphous solid dispersion (ASD) of cyclosporine A (CsA) by a fine droplet drying (FDD) process for improvement in oral absorption of CsA. CsA and hydroxypropyl cellulose-SSL were dissolved in 1,4-dioxane, and the solution was powdered by the FDD process to obtain the ASD formulation of CsA (ASD/CsA). The ASD/CsA was characterized in terms of morphology, particle size distribution, crystallinity, dissolution behavior, physicochemical stability, and pharmacokinetic behavior in rats. The ASD/CsA was obtained in the form of uniform spherical particles, and the span factor was calculated to be ca. 0.4. CsA in the formulation existed in an amorphous state. The ASD/CsA exhibited a higher dissolution behavior of CsA than amorphous CsA, whereas storage of the ASD/CsA under accelerated conditions led to impairment in the dissolution behavior. The constant release of CsA from non-aged ASD/CsA was observed during dissolution testing. After oral administration of CsA samples (10mg-CsA/kg) in rats, the ASD/CsA showed a high and sustained plasma concentration of CsA as evidenced by a 18-fold increase in the oral bioavailability of CsA compared with amorphous CsA. From these findings, the FDD process might be an efficacious option for the ASD formulation of CsA with enhanced biopharmaceutics properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Silica hydride intermediate for octadecylsilica and phenyl bonded phase preparation via heterogeneous hydrosilation in supercritical carbon dioxide.

PubMed

Scully, N M; Ashu-Arrah, B A; Nagle, A P; Omamogho, J O; O'Sullivan, G P; Friebolin, V; Dietrich, B; Albert, K; Glennon, J D

2011-04-15

Investigations into the preparation of silica hydride intermediate in supercritical carbon dioxide (sc-CO(2)) that avoids the use of organic solvents such as toluene or dioxane are described. The effects of reaction temperature, pressure and time on the surface coverage of the supercritical fluid generated silica hydride intermediate were studied. Under optimised supercritical conditions of 120°C, 483 bar and 3 h reaction time, silica hydride (Si-H) conversion efficiencies of ca. 40% were achieved for the hydride intermediate prepared from a monofunctional silane reagent (dimethylmethoxysilane). Si-H conversion efficiencies (as determined from (29)Si CP-MAS NMR spectral analysis) for the hydride intermediate prepared from triethoxysilane (TES) in sc-CO(2) were found to be comparable to those obtained using a TES silanisation approach in an organic solvent. (13)C and (29)Si CP-MAS-NMR spectroscopy was employed to provide a complete structural assignment of the silica hydride intermediates. Furthermore, supercritical CO(2) was subsequently employed as a reaction medium for the heterogenous hydrosilation of silica hydride with octadecene and with styrene, in the presence of a free radical initiator. These supercritical fluid generated reversed-phase materials were prepared in a substantially reduced reaction time (3 h) compared to organic solvent based methods (100 h reaction time). Silica functionalisation in sc-CO(2) presents an efficient and clean alternative to organic solvent based methods for the preparation of important silica hydride intermediate and silica bonded stationary phases via a hydrosilation approach. Copyright © 2010 Elsevier B.V. All rights reserved.

Computational Elucidation of a Role That Brønsted Acidification of the Lewis Acid-Bound Water Might Play in the Hydrogenation of Carbonyl Compounds with H2 in Lewis Basic Solvents.

PubMed

Heshmat, Mojgan; Privalov, Timofei

2017-08-25

Brønsted acidification of water by Lewis acid (LA) complexation is one of the fundamental principles in chemistry. Using transition-state calculations (TS), herein we investigate the role that Brønsted acidification of the LA-bound water might play in the mechanism of the hydrogenation of carbonyl compounds in Lewis basic solvents under non-anhydrous conditions. The potential energy scans and TS calculations were carried out with a series of eight borane LAs as well as the commonly known strong LA AlCl 3 in 1,4-dioxane or THF as Lewis basic solvents. Our molecular model consists of the dative LA-water adduct with hydrogen bonds to acetone and a solvent molecule plus one additional solvent molecule that participates is the TS structure describing the cleavage of H 2 at acetone's carbonyl carbon atom. In all the molecular models applied here, acetone (O=CMe 2 ) is the archetypical carbonyl substrate. We demonstrate that Brønsted acidification of the LA-bound water can indeed lower the barrier height of the solvent-involving H 2 -cleavage at the acetone's carbonyl carbon atom. This is significant because at present it is believed that the mechanism of the herein considered reaction is described by the same mechanism regardless of whether the reaction conditions are strictly anhydrous or non-anhydrous. Our results offer an alternative to this belief that warrants consideration and further study. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Assessment of the thermodynamic properties of poly(2,2,2-trifluoroethyl methacrylate) by inverse gas chromatography.

PubMed

Papadopoulou, Stella K; Panayiotou, Costas

2014-01-10

The thermodynamic properties of poly(2,2,2-trifluoroethyl methacrylate) (PTFEMA) were determined by the aid of the inverse gas chromatography technique (IGC), at infinite dilution. The interactions between the polymer and 15 solvents were examined in the temperature range of 120-150 °C via the estimation of the thermodynamic sorption parameters, the parameters of mixing at infinite dilution, the weight fraction activity coefficients and the Flory-Huggins interaction parameters. Additionally, the total and the partial solubility parameters of PTFEMA were estimated. The findings of this work indicate that the type and strength of the intermolecular interactions between the polymer and the solvents are strongly depended on the functional groups of the polymer and the solvents. The proton acceptor character of the polymer is responsible for the preferential solubility of PTFEMA in chloroform which acts as a proton donor solvent. The results also reveal that the polymer is insoluble in alkanes and alcohols whereas it presents good miscibility with polar solvents, especially with 2-butanone, 2-pentanone and 1,4-dioxane. Furthermore, the total and dispersive solubility parameters appear diminishing upon temperature rise, whereas the opposite behavior is noticed for the polar and hydrogen bonding solubility parameters. The latter increase with temperature, probably, due to conformational changes of the polymer on the solid support. Finally, comparison of the solubilization profiles of fluorinated methacrylic polymers studied by IGC, leads to the conclusion that PTFEMA is more soluble compared to polymers with higher fluorine content. Copyright © 2013 Elsevier B.V. All rights reserved.

Synthesis, DFT calculations, electronic structure, electronic absorption spectra, natural bond orbital (NBO) and nonlinear optical (NLO) analysis of the novel 5-methyl-8H-benzo[h]chromeno[2,3-b][1,6] naphthyridine-6(5H),8-dione (MBCND)

NASA Astrophysics Data System (ADS)

Halim, Shimaa Abdel; Ibrahim, Magdy A.

2017-02-01

New derivative of heteroannulated chromone identified as 5-methyl-8H-benzo[h]chromeno[2,3-b][1,6]naphthyridine-6(5H),8-dione (5, MBCND) was easily and efficiently synthesized from DBU catalyzed condensation reaction of 2-aminochromone-3-carboxaldehyde (1) with 4-hydroxy-1-methylquinolin-2(1H)-one (2). The same product 5 was isolated from condensation reaction of aldeyde 1 with 3-(4-hydroxy-1-methyl-2-oxo-1,2-dihydroquinolin-3-yl)-3-oxopropanoic acid (3) or ethyl 4-(4-hydroxy-1-methyl-2-oxo-1,2-dihydroquinolin-3-yl)-2,4-dioxobutanoate (4). Structure of compound (5, MBCND) was deduced based on their elemental analyses and spectral data (IR, 1H NMR and mass spectra). Density Functional Theory (DFT) calculations at the B3LYP/6-311G (d,p) level of theory have been carried out to investigate the equilibrium geometry of the novel compound (5, MBCND). Moreover, total energy, energy of HOMO and LUMO and Mullikan atomic charges were calculated. In addition, the dipole moment, theoretical study of the electronic structure, nonlinear optical properties (NLO), and natural bonding orbital (NBO) analysis and orientation have been performed and discussed. Also the electronic absorption spectra were measured in polar (methanol) as well as non polar (dioxane) solvents and the assignment of the observed bands has been discussed by TD-DFT calculations. The correspondences between calculated and experimental transitions energies are satisfactory.

Experimental consideration of capillary chromatography based on tube radial distribution of ternary mixture carrier solvents under laminar flow conditions.

PubMed

Jinno, Naoya; Hashimoto, Masahiko; Tsukagoshi, Kazuhiko

2011-01-01

A capillary chromatography system has been developed based on the tube radial distribution of the carrier solvents using an open capillary tube and a water-acetonitrile-ethyl acetate mixture carrier solution. This tube radial distribution chromatography (TRDC) system works under laminar flow conditions. In this study, a phase diagram for the ternary mixture carrier solvents of water, acetonitrile, and ethyl acetate was constructed. The phase diagram that included a boundary curve between homogeneous and heterogeneous solutions was considered together with the component ratios of the solvents in the homogeneous carrier solutions required for the TRDC system. It was found that the TRDC system performed well with homogeneous solutions having component ratios of the solvents that were positioned near the homogeneous-heterogeneous solution boundary of the phase diagram. For preparing the carrier solutions of water-hydrophilic/hydrophobic organic solvents for the TRDC system, we used for the first time methanol, ethanol, 1,4-dioxane, and 1-propanol, instead of acetonitrile (hydrophilic organic solvent), as well as chloroform and 1-butanol, instead of ethyl acetate (hydrophobic organic solvent). The homogeneous ternary mixture carrier solutions were prepared near the homogeneous-heterogeneous solution boundary. Analyte mixtures of 2,6-naphthalenedisulfonic acid and 1-naphthol were separated with the TRDC system using these homogeneous ternary mixture carrier solutions. The pressure change in the capillary tube under laminar flow conditions might alter the carrier solution from homogeneous in the batch vessel to heterogeneous, thus affecting the tube radial distribution of the solvents in the capillary tube.

Synthesis, DFT band structure calculations, optical and photoelectrical characterizations of the novel 5-hydroxy-4-methoxy-7-oxo-7H-furo[3,2-g]chromene-6-carbonitrile (HMOFCC)

NASA Astrophysics Data System (ADS)

Ibrahim, Magdy A.; Halim, Shimaa Abdel; Roushdy, N.; Farag, A. A. M.; El-Gohary, Nasser M.

2017-11-01

Reaction of 4-methoxy-5-oxo-5H-furo[3,2-g]chromene-6-carboxaldehyde (1) with hydroxylamine hydrochloride resulted in ring transformation producing the novel 5-hydroxy-4-methoxy-7-oxo-7H-furo[3,2-g]chromene-6-carbonitrile (HMOFCC). The structure was deduced based on its correct elemental analysis and spectral data (IR, 1H NMR, 13C NMR and mass spectra). The geometries of the HMOFCC were completely optimized by means of DFT-B3LYP/6-311++G (d,p) theoretical level. The ground state properties such as; total energy, the energy of HOMO and LUMO and Mulliken atomic charges were also determined. In addition, the two solvents; polar (methanol) and nonpolar (dioxane) were utilized to extract the electronic absorption spectra. The assignment of the detected bands was discussed by TD-DFT calculations. A cauliflower-like, as well as, needle-like leaves morphologies were observed using scanning electron microscope images. Two direct optical band gaps were extracted from the photon energy dependence of absorption coefficient at the band edges and found to be 1.16 and 2.56 eV. A characteristic emission peak of photoluminescence spectrum was observed and shifted depending on the solvent type. A remarkable rectification characteristic of HMOFCC/p-Si heterojunction confirms the diode-like behavior. The main important parameters like series resistance, shunt resistance and reverse saturation current show illumination dependence under influence of the illumination intensity range 20-100 mW/cm2. The heterojunction based HMOFCC showed phototransient properties under various illumination intensities which give the recommendation for the studied heterojunction in the field of optoelectronic device application.

Role of orexin-1 receptor mechanisms on compulsive food consumption in a model of binge eating in female rats.

PubMed

Piccoli, Laura; Micioni Di Bonaventura, Maria Vittoria; Cifani, Carlo; Costantini, Vivian J A; Massagrande, Mario; Montanari, Dino; Martinelli, Prisca; Antolini, Marinella; Ciccocioppo, Roberto; Massi, Maurizio; Merlo-Pich, Emilio; Di Fabio, Romano; Corsi, Mauro

2012-08-01

Orexins (OX) and their receptors (OXR) modulate feeding, arousal, stress, and drug abuse. Neural systems that motivate and reinforce drug abuse may also underlie compulsive food seeking and intake. Therefore, the effects of GSK1059865 (5-bromo-N-[(2S,5S)-1-(3-fluoro-2-methoxybenzoyl)-5-methylpiperidin-2-yl]methyl-pyridin-2-amine), a selective OX(1)R antagonist, JNJ-10397049 (N-(2,4-dibromophenyl)-N'-[(4S,5S)-2,2-dimethyl-4-phenyl-1,3-dioxan-5-yl]urea), a selective OX(2)R antagonist, and SB-649868 (N-[((2S)-1-{[5-(4-fluorophenyl)-2-methyl-1,3-thiazol-4-yl]carbonyl}-2-piperidinyl)methyl]-1-benzofuran-4-carboxamide), a dual OX(1)/OX(2)R antagonist were evaluated in a binge eating (BE) model in female rats. BE of highly palatable food (HPF) was evoked by three cycles of food restriction followed by stress, elicited by exposing rats to HPF, but preventing them from having access to it for 15 min. Pharmacokinetic assessments of all compounds were obtained under the same experimental conditions used for the behavioral experiments. Topiramate was used as the reference compound as it selectively blocks BE in rats and humans. Dose-related thresholds for sleep-inducing effects of the OXR antagonists were measured using polysomnography in parallel experiments. SB-649868 and GSK1059865, but not JNJ-10397049, selectively reduced BE for HPF without affecting standard food pellet intake, at doses that did not induce sleep. These results indicate, for the first time, a major role of OX(1)R mechanisms in BE, suggesting that selective antagonism at OX(1)R could represent a novel pharmacological treatment for BE and possibly other eating disorders with a compulsive component.

Determination of fatty alcohol ethoxylates and alkylether sulfates by anionic exchange separation, derivatization with a cyclic anhydride and liquid chromatography.

PubMed

Beneito-Cambra, M; Ripoll-Seguer, L; Herrero-Martínez, J M; Simó-Alfonso, E F; Ramis-Ramos, G

2011-11-25

A method for the separation, characterization and determination of fatty alcohol ethoxylates (FAE) and alkylether sulfates (AES) in industrial and environmental samples is described. Separation of the two surfactant classes was achieved in a 50:50 methanol-water medium by retaining AES on a strong anionic exchanger (SAX) whereas most FAE were eluted. After washing the SAX cartridges to remove cations, the residual hydrophobic FAE were eluted by increasing methanol to 80%. Finally, AES were eluted using 80:20 and 95:5 methanol-concentrated aqueous HCl mixtures. Methanol and water were removed from the FAE and AES fractions, and the residues were dissolved in 1,4-dioxane. In this medium, esterification of FAE and transesterification of AES with a cyclic anhydride was performed. Phthalic and diphenic anhydrides were used to derivatizate the surfactants in industrial samples and seawater extracts, respectively. Separation of the derivatized oligomers was achieved by gradient elution on a C8 column with acetonitrile/water in the presence of 0.1% acetic acid. Good resolution between both the hydrocarbon series and the successive oligomers within the series was achieved. Cross-contamination of FAE with AES and vice versa was not observed. Using dodecyl alcohol as calibration standard, and correction of the peak areas of the derivatized oligomers by their respective UV-vis response factors, both FAE and AES were evaluated. After solid-phase extraction on C18, the proposed method was successfully applied to the characterization and determination of the two surfactant classes in industrial samples and in seawater. Copyright © 2011 Elsevier B.V. All rights reserved.

Dynamics and mechanism of UV-damaged DNA repair in indole-thymine dimer adduct: molecular origin of low repair quantum efficiency.

PubMed

Guo, Xunmin; Liu, Zheyun; Song, Qinhua; Wang, Lijuan; Zhong, Dongping

2015-02-26

Many biomimetic chemical systems for repair of UV-damaged DNA showed very low repair efficiency, and the molecular origin is still unknown. Here, we report our systematic characterization of the repair dynamics of a model compound of indole-thymine dimer adduct in three solvents with different polarity. By resolving all elementary steps including three electron-transfer processes and two bond-breaking and bond-formation dynamics with femtosecond resolution, we observed the slow electron injection in 580 ps in water, 4 ns in acetonitrile, and 1.38 ns in dioxane, the fast back electron transfer without repair in 120, 150, and 180 ps, and the slow bond splitting in 550 ps, 1.9 ns, and 4.5 ns, respectively. The dimer bond cleavage is clearly accelerated by the solvent polarity. By comparing with the biological repair machine photolyase with a slow back electron transfer (2.4 ns) and a fast bond cleavage (90 ps), the low repair efficiency in the biomimetic system is mainly determined by the fast back electron transfer and slow bond breakage. We also found that the model system exists in a dynamic heterogeneous C-clamped conformation, leading to a stretched dynamic behavior. In water, we even identified another stacked form with ultrafast cyclic electron transfer, significantly reducing the repair efficiency. Thus, the comparison of the repair efficiency in different solvents is complicated and should be cautious, and only the dynamics by resolving all elementary steps can finally determine the total repair efficiency. Finally, we use the Marcus electron-transfer theory to analyze all electron-transfer reactions and rationalize all observed electron-transfer dynamics.

Three separate classes of bacterial ice nucleation structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turner, M.A.; Arellano, F.; Kozloff, L.M.

1990-05-01

Studies of the properties of the ice nucleation structure exposed on the surfaces of various bacteria such as Pseudomonas syringae, Erwinia herbicola, or various strains of Ice+ recombinant Escherichia coli have shown that there are clearly three major related but chemically distinct types of structures on these cells. First, the ability of Ice+ cells to nucleate super-cooled D2O has been examined, and it has been found that this ability (relative to the ability of the same cells to nucleate super-cooled H2O) exhibited three characteristic nucleating patterns. The rarest structure, called class A, is found on only a small fraction ofmore » cells in a culture, nucleates H2O at temperatures above -4.4 degrees C, and is an effective nucleator of super-cooled D2O. A second class of structure, called class B, is found on a larger portion of the cells, nucleates H2O between -4.8 and -5.7 degrees C, and is a relatively poor nucleator of super-cooled D2O. The class C structure is found on almost all cells and nucleates at -7.6 degrees C or colder. These three classes of structures were also differentiated by their sensitivities to low concentrations of water-miscible organic solvents such as dioxane or dimethyl sulfoxide. Depending on the specific bacterial strain, the addition of these solvents to bacterial suspensions lowered the nucleation activity of the class A structure by 1,000-fold or more. The nucleation activities of class B structures in the same culture were highly resistant to these compounds and were lowered only by 20 to 40%.« less

Quinolinone and pyridopyrimidinone inhibitors of DNA-dependent protein kinase.

PubMed

Barbeau, Olivier R; Cano-Soumillac, Celine; Griffin, Roger J; Hardcastle, Ian R; Smith, Graeme C M; Richardson, Caroline; Clegg, William; Harrington, Ross W; Golding, Bernard T

2007-08-21

8-Substituted 2-morpholin-4-yl-quinolin-4-ones and 9-substituted 2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-ones with selected aryl and heteroaryl groups as the substituent have been synthesised as potential inhibitors of DNA-dependent protein kinase. A multiple-parallel approach, employing Suzuki cross-coupling methodology, was utilised in the preparation of 8-substituted 2-morpholin-4-yl-quinolin-4-ones. For this purpose 8-bromo-2-morpholin-4-yl-quinolin-4-one was required as an intermediate. This compound was obtained by adapting a literature route in which thermal cyclocondensation of (2-bromoanilino)-morpholin-4-yl-5-methylene-2,2-dimethyl[1,3]dioxane-4,6-dione afforded 8-bromo-2-morpholin-4-yl-quinolin-4-one. A multiple-parallel approach, employing Suzuki cross-coupling methodology, was also utilised to prepare 9-substituted 2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-ones using 9-hydroxy-2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-one O-trifluoromethanesulfonate as an intermediate. 8-Substituted 2-morpholin-4-yl-quinolin-4-ones and 9-substituted 2-morpholin-4-yl-pyrido[1,2-a]pyrimidin-4-ones were both inhibitors of DNA-dependent protein kinase. When the substituent was dibenzothiophen-4-yl, dibenzofuran-4-yl or biphen-3-yl, IC50 values in the low nanomolar range were observed. Interestingly, the pyridopyrimidinones and quinolinones were essentially equipotent with the corresponding 8-substituted 2-morpholin-4-yl-chromen-4-ones previously reported (I. R. Hardcastle, X. Cockcroft, N. J. Curtin, M. Desage El-Murr, J. J. J. Leahy, M. Stockley, B. T. Golding, L. Rigoreau, C. Richardson, G. C. M. Smith and R. J. Griffin, J. Med. Chem., 2005, 48, 7829-7846).

Compatibility Studies Of Blends Of PPG 4000 And PEG 4000 Using Viscosity Technique

NASA Astrophysics Data System (ADS)

Venkatramanan, K.; Arumugam, V.

2010-06-01

Certain properties of polymers can be enhanced by mixing it with another polymer. When two or more polymers are intimately mixed in a single continuous solid product, the composition is generally referred to as a polymer blend or polyblend. Depending upon the degree of miscibility or immiscibility, such a polyblend may resemble a random copolymer or a block or graft copolymer or it may show micro or macro heterogeneous separation into a multiphase system. Viscosity method is simple and it offers very useful information about the relationship between dilute solution properties and bulk structure of the polymer blend. The basic idea of using viscosity as a parameter for compatibility determination of polymer blends lies in the fact that in solution the repulsive interaction may cause shrinkage of polymer coils resulting in a viscosity of the polymer mixture that is lower than the value calculated from viscosities of the pure components on the assumption of the additive law. In the present study, an attempt has been made to blend PPG 4000 with PEG 4000 in 1,4 -Dioxane at 303K at 1% concentration. The blend compositions were formed in the ratio 0:1, 0.2:0.8, 0.4:0.6, 0.5:0.5, 0.6:0.4, 0.8:0.2, 1:0. Relative viscosity of the blend compositions was determined and the values are nonlinear which showed incompatibility. Miscibility nature of the blends were determined further using additive law, log additive law and free volume additive law and the experimental values in all the cases showed negative deviation which is a characteristic of immiscible blend. The miscibility nature of the blend was further confirmed through density, ultrasonic velocity, refractive index and other techniques. The blend showed immiscibility.

Tuned range separated hybrid functionals for solvated low bandgap oligomers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Queiroz, Thiago B. de, E-mail: thiago.branquinho-de-queiroz@uni-bayreuth.de; Kümmel, Stephan

2015-07-21

The description of charge transfer excitations has long been a challenge to time dependent density functional theory. The recently developed concept of “optimally tuned range separated hybrid (OT-RSH) functionals” has proven to describe charge transfer excitations accurately in many cases. However, describing solvated or embedded systems is yet a challenge. This challenge is not only computational but also conceptual, because the tuning requires identifying a specific orbital, typically the highest occupied one of the molecule under study. For solvated molecules, this orbital may be delocalized over the solvent. We here demonstrate that one way of overcoming this problem is tomore » use a locally projected self-consistent field diagonalization on an absolutely localized molecular orbital expansion. We employ this approach to determine ionization energies and the optical gap of solvated oligothiophenes, i.e., paradigm low gap systems that are of relevance in organic electronics. Dioxane solvent molecules are explicitly represented in our calculations, and the ambiguities of straightforward parameter tuning in solution are elucidated. We show that a consistent estimate of the optimal range separated parameter (ω) at the limit of bulk solvation can be obtained by gradually extending the solvated system. In particular, ω is influenced by the solvent beyond the first coordination sphere. For determining ionization energies, a considerable number of solvent molecules on the first solvation shell must be taken into account. We demonstrate that accurately calculating optical gaps of solvated systems using OT-RSH can be done in three steps: (i) including the chemical environment when determining the range-separation parameter, (ii) taking into account the screening due to the solvent, and (iii) using realistic molecular geometries.« less

Determination of a cost-effective air pollution control technology for the control of VOC and HAP emissions from a steroids processing plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamel, T.M.

1997-12-31

A steroids processing plant located in northeastern Puerto Rico emits a combined average of 342 lb/hr of hazardous air pollutants (HAPs) and volatile organic compounds (VOCs) from various process operations. The approach that this facility used to implement maximum achievable control technology (MACT) may assist others who must contend with MACT for pharmaceutical or related manufacturing facilities. Federal air regulations define MACT standards for stationary sources emitting any of 189 HAPs. The MACT standards detailed in the NESHAPs are characterized by industry and type of emission control system or technology. It is anticipated that the standard will require HAP reductionsmore » of approximately 95%. The steroid plant`s emissions include the following pollutant loadings: VOC/HAP Emission Rate (lb/hr): Methanol 92.0; Acetone 35.0; Methylene chloride 126.0; Chloroform 25.0; Ethyl acetate 56.0; Tetrahydrofuran 5.00; and 1,4-Dioxane 3.00. The facility`s existing carbon adsorption control system was nearing the end of its useful life, and the operators sought to install an air pollution control system capable of meeting MACT requirements for the pharmaceutical industry. Several stand-alone and hybrid control technologies were considered for replacement of the carbon adsorption system at the facility. This paper examines the following technologies: carbon adsorption, membrane separation, thermal oxidation, membrane separation-carbon adsorption, and condensation-carbon adsorption. Each control technology is described; the advantages and disadvantages of utilizing each technology for the steroid processing plant are examined; and capital and operating costs associated with the implementation of each technology are presented. The rationale for the technology ultimately chosen to control VOC and HAP emissions is presented.« less

Toward the realization of a compact chemical sensor platform using quantum cascade lasers

NASA Astrophysics Data System (ADS)

Holthoff, Ellen L.; Marcus, Logan S.; Pellegrino, Paul M.

2015-05-01

The Army is investigating several spectroscopic techniques (e.g., infrared spectroscopy) that could allow for an adaptable sensor platform. Traditionally, chemical sensing platforms have been hampered by the opposing concerns of increasing sensor capability while maintaining a minimal package size. Current sensors, although reasonably sized, are geared to more classical chemical threats, and the ability to expand their capabilities to a broader range of emerging threats is uncertain. Recently, photoacoustic spectroscopy, employed in a sensor format, has shown enormous potential to address these ever-changing threats, while maintaining a compact sensor design. In order to realize the advantage of photoacoustic sensor miniaturization, light sources of comparable size are required. Recent research has employed quantum cascade lasers (QCLs) in combination with MEMS-scale photoacoustic cell designs. The continuous tuning capability of QCLs over a broad wavelength range in the mid-infrared spectral region greatly expands the number of compounds that can be identified. Results have demonstrated that utilizing a tunable QCL with a MEMS-scale photoacoustic cell produces favorable detection limits (ppb levels) for chemical targets (e.g., dimethyl methyl phosphonate (DMMP), vinyl acetate, 1,4-dioxane). Although our chemical sensing research has benefitted from the broad tuning capabilities of QCLs, the limitations of these sources must be considered. Current commercially available tunable systems are still expensive and obviously geared more toward laboratory operation, not fielding. Although the laser element itself is quite small, the packaging, power supply, and controller remain logistical burdens. Additionally, operational features such as continuous wave (CW) modulation and laser output powers while maintaining wide tunability are not yet ideal for a variety of sensing applications. In this paper, we will discuss our continuing evaluation of QCL technology as it matures in relation to our ultimate goal of a universal compact chemical sensor platform.

A novel metal-organic framework for high storage and separation of acetylene at room temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, Xing, E-mail: star1987@hdu.edu.cn; Wang, Huizhen; Ji, Zhenguo

2016-09-15

A novel 3D microporous metal-organic framework with NbO topology, [Cu{sub 2}(L)(H{sub 2}O){sub 2}]∙(DMF){sub 6}·(H{sub 2}O){sub 2} (ZJU-10, ZJU = Zhejiang University; H{sub 4}L =2′-hydroxy-[1,1′:4′,1″-terphenyl]-3,3″,5,5″-tetracarboxylic acid; DMF =N,N-dimethylformamide), has been synthesized and structurally characterized. With suitable pore sizes and open Cu{sup 2+} sites, ZJU-10a exhibits high BET surface area of 2392 m{sup 2}/g, as well as moderately high C{sub 2}H{sub 2} volumetric uptake capacity of 132 cm{sup 3}/cm{sup 3}. Meanwhile, ZJU-10a is a promising porous material for separation of acetylene from methane and carbon dioxide gas mixtures at room temperature. - Graphical abstract: A new NbO-type microporous metal-organic framework ZJU-10 withmore » suitable pore size and open Cu{sup 2+} sites was synthesized to realize the strong interaction with acetylene molecules, which can separate the acetylene from methane and carbon dioxane gas mixtures at room temperature. Display Omitted - Highlights: • A novel 3D NbO-type microporous metal-organic framework ZJU-10 was solvothermally synthesized and structurally characterized. • ZJU-10a exhibits high BET surface area of 2392 m{sup 2}/g. • ZJU-10a shows a moderately high C{sub 2}H{sub 2} gravimetric (volumetric) uptake capacity of 174 (132) cm{sup 3}/g at 298 K and 1 bar. • ZJU-10a can separate acetylene from methane and carbon dioxide gas mixtures at room temperature.« less

π-π-Induced aggregation and single-crystal fluorescence anisotropy of 5,6,10b-tri-aza-acephenanthrylene.

PubMed

Ostrowska, Katarzyna; Ceresoli, Davide; Stadnicka, Katarzyna; Gryl, Marlena; Cazzaniga, Marco; Soave, Raffaella; Musielak, Bogdan; Witek, Łukasz J; Goszczycki, Piotr; Grolik, Jarosław; Turek, Andrzej M

2018-05-01

The structural origin of absorption and fluorescence anisotropy of the single crystal of the π-conjugated heterocyclic system 5,6,10b-tri-aza-acephenan-thrylene, TAAP, is presented in this study. X-ray analysis shows that the crystal framework in the space group P [Formula: see text] is formed by centrosymmetric dimers of face-to-face mutually oriented TAAP molecules joined by π-π non-covalent interactions. The conformation of the TAAP molecule is stabilized by intramolecular C-H⋯N( sp 2 ), N( sp 2 )H⋯π(CN), and C-H⋯O( sp 2 ) hydrogen bonds. The presence of weak π-π interactions is confirmed by quantum theory of atoms in molecules (QTAIM) and non-covalent interaction (NCI) analysis. The analysis of the optical spectra of TAAP in solution and in the solid state does not allow the specification of the aggregation type. DFT calculations for the dimer in the gas phase indicate that the lowest singlet excitation is forbidden by symmetry, suggesting H-type aggregation, even though the overall absorption spectrum is bathochromically shifted as for the J-type. The experimental determination of the permanent dipole moment of a TAAP molecule in 1,4-dioxane solution indicates the presence of the monomer form. The calculated absorption and emission spectra of the crystal in a simple approximation are consistent with the experimentally determined orientation of the absorption and emission transition dipole moments in TAAP single crystals. The electrostatic interaction between monomers with a permanent dipole moment ( ca 4 D each) could result in the unusual spectroscopic JH-aggregate behaviour of the TAAP dimer.

Generation of ROS mediated by mechanical waves (ultrasound) and its possible applications.

PubMed

Duco, Walter; Grosso, Viviana; Zaccari, Daniel; Soltermann, Arnaldo T

2016-10-15

The thermal decomposition of 9,10 diphenylanthracene peroxide (DPAO 2 ) generates DPA and a mix of triplet and singlet molecular oxygen. For DPAO 2 the efficiency to produce singlet molecular oxygen is 0.35. On the other hand, it has shown that many thermal reactions can be carried out through the interaction of molecules with ultrasound. Ultrasound irradiation can create hydrodynamic stress (sonomechanical process), inertial cavitation (pyrolitic process) and long range effects mediated by radicals or ROS. Sonochemical reactions can be originated by pyrolytic like process, shock mechanical waves, thermal reactions and radical and ROS mediated reactions. Sonolysis of pure water can yield hydrogen or hydroxyl radicals and hydrogen peroxide (ROS). When DPAO 2 in 1,4 dioxane solution is treated with 20 or 24kHz and different power intensity the production of molecular singlet oxygen is observed. Specific scavengers like tetracyclone (TC) are used to demonstrate it. The efficiency now is 0.85 showing that the sonochemical process is much more efficient that the thermal one. Another endoperoxide, artemisinin was also studied. Unlike the concept of photosensitizer of photodynamic therapy, in spite of large amount of reported results in literature, the term sonosensitizer and the sonosensitization process are not well defined. We define sonosensitized reaction as one in which a chemical species decompose as consequence of cavitation phenomena producing ROS or other radicals and some other target species does undergo a chemical reaction. The concept could be reach rapidly other peroxides which are now under experimental studies. For artemisinin, an important antimalarian and anticancer drug, was established that ultrasound irradiation increases the effectiveness of the treatment but without any explanation. We show that artemisinin is an endoperoxide and behaves as a sonosensitizer in the sense of our definition. Copyright © 2016 Elsevier Inc. All rights reserved.

Surface-modified functionalized polycaprolactone scaffolds for bone repair: in vitro and in vivo experiments.

PubMed

Jensen, Jonas; Rölfing, Jan Hendrik Duedal; Le, Dang Quang Svend; Kristiansen, Asger Albaek; Nygaard, Jens Vinge; Hokland, Lea Bjerre; Bendtsen, Michael; Kassem, Moustapha; Lysdahl, Helle; Bünger, Cody Eric

2014-09-01

A porcine calvaria defect study was carried out to investigate the bone repair potential of three-dimensional (3D)-printed poly-ε-caprolactone (PCL) scaffolds embedded with nanoporous PCL. A microscopic grid network was created by rapid prototyping making a 3D-fused deposition model (FDM-PCL). Afterward, the FDM-PCL scaffolds were infused with a mixture of PCL, water, and 1,4-dioxane and underwent a thermal-induced phase separation (TIPS) followed by lyophilization. The TIPS process lead to a nanoporous structure shielded by the printed microstructure (NSP-PCL). Sixteen Landrace pigs were divided into two groups with 8 and 12 weeks follow-up, respectively. A total of six nonpenetrating holes were drilled in the calvaria of each animal. The size of the cylindrical defects was h 10 mm and Ø 10 mm. The defects were distributed randomly using following groups: (a) NSP-PCL scaffold, (b) FDM-PCL scaffold, (c) autograft, (d) empty defect, (a1) NSP-PCL scaffold + autologous mononuclear cells, and (a2) NSP-PCL scaffold + bone morphogenetic protein 2. Bone volume to total volume was analyzed using microcomputed tomography (µCT) and histomorphometry. The µCT and histological data showed significantly less bone formation in the NSP-PCL scaffolds in all three variations after both 8 and 12 weeks compared to all other groups. The positive autograft control had significantly higher new bone formation compared to all other groups except the FDM-PCL when analyzed using histomorphometry. The NSP-PCL scaffolds were heavily infiltrated with foreign body giant cells suggesting an inflammatory response and perhaps active resorption of the scaffold material. The unmodified FDM-PCL scaffold showed good osteoconductivity and osseointegration after both 8 and 12 weeks. © 2013 Wiley Periodicals, Inc.

Fluorescence spectroscopy and amplified spontaneous emission (ASE) of phenylimidazoles: predicted vibronic coupling along the excited-state intramolecular proton transfer in 2-(2'-hydroxyphenyl)imidazoles.

PubMed

del Valle, Juan Carlos; Claramunt, R M; Catalán, J

2008-06-26

Methylation at the 1N position of 2-phenylimidazole provides the shortest wavelength for a liquid-state laser dye reported to date; that is, the 1-methyl-2-phenylimidazole molecule in cyclohexane solution yields amplified spontaneous emission (ASE) with a peak wavelength at 314.5 nm and a constant laser gain value of 5 cm(-1) from 310 to 317 nm. Methyl substitution in this case favors the appearance of laser action (owing to a torsion-vibrational mechanism) in cyclohexane as compared with the nonmethylated species which does not exhibit ASE in this solvent. The 2-(2'-hydroxyphenyl)imidazole molecules give rise to ASE with high gain values (ca. 9 cm(-1)) at 450 and 466 nm. The mechanism of population inversion is understood in terms of a vibronic coupling between the hydroxyl stretching motion and the torsional vibration of the phenyl and imidazole rings. The proton-transfer spectroscopy of 2-(2'-hydroxyphenyl)imidazoles is studied in dioxane, cyclohexane, dimethyl sulfoxide, methanol, and water. The greater the acidity of the solvent the greater the disruption of the intramolecular hydrogen bond; solvent acidity is the main parameter which favors formation of the open-form species in the ground electronic state. Methyl substitution at the 1N position favors formation of the open species for 2-hydroxyphenylimidazoles in the ground electronic state, which decreases their own capacity to undergo ASE. Low-temperature absorption spectroscopy confirms aggregation processes for 2-(2'-hydroxyphenyl)imidazoles in solution. In accordance with X-ray analyses in the solid phase, these molecules form associations through intermolecular chains of the type N-H...O or O-H...N.

Characterization and structural analysis of the potent antiparasitic and antiviral agent tizoxanide

NASA Astrophysics Data System (ADS)

Bruno, Flavia P.; Caira, Mino R.; Martin, Eliseo Ceballos; Monti, Gustavo A.; Sperandeo, Norma R.

2013-03-01

Tizoxanide [2-(hydroxy)-N-(5-nitro-2-thiazolyl)benzamide, TIZ] is a new potent anti-infective agent which may enhance current therapies for leishmaniasis, Chagas disease and viral hepatitis. The aim of this study was to identify the conformational preferences that may be related to the biological activity of TIZ by resolving its crystal structure and characterizing various physicochemical properties, including its experimental vibrational and 13C nuclear magnetic resonance properties, behavior on heating and solubility in several solvents at 25 °C. TIZ crystallizes from dimethylformamide as the carboxamide tautomer in the triclinic system, space group P(-1) (No. 2) with the following unit cell parameters at 173(2) K: a = 5.4110(3) Å, b = 7.3315(6) Å, c = 13.5293(9) Å, α = 97.528(3), β = 95.390(4), γ = 97.316(5), V = 524.41(6) Å3, Z = 2, Dc = 1.680 g/cm3, R1 = 0.0482 and wR2 = 0.0911 for 2374 reflections. This modification of TIZ has a 'graphitic' structure and is composed of tightly packed layers of extensively hydrogen-bonded molecules. The various spectroscopic data [Diffuse Fourier transform infrared (DRIFT) and FT-Raman, recorded in the range 3600-500 and 4000-200 cm-1 respectively, and solid-state 13C NMR] were consistent with the structure determined by X-ray crystallography. From DSC, TG and thermomicroscopy, it was concluded that TIZ is thermally stable as a solid and that melting is not an isolated event from the one-step thermal decomposition that it undergoes above 270 °C. This modification of TIZ is practically insoluble in water and slightly soluble in polar aprotic solvents such as dimethylsulfoxide, dimethylformamide and dioxane.

TES buffer-induced phase separation of aqueous solutions of several water-miscible organic solvents at 298.15 K: phase diagrams and molecular dynamic simulations.

PubMed

Taha, Mohamed; Lee, Ming-Jer

2013-06-28

Water and the organic solvents tetrahydrofuran, 1,3-dioxolane, 1,4-dioxane, 1-propanol, 2-propanol, tert-butanol, acetonitrile, or acetone are completely miscible in all proportions at room temperature. Here, we present new buffering-out phase separation systems that the above mentioned organic aqueous solutions can be induced to form two liquid phases in the presence of a biological buffer 2-[[1,3-dihydroxy-2-(hydroxymethyl)propan-2-yl]amino]ethanesulfonic acid (TES). The lower liquid phase is rich in water and buffer, and the upper phase is organic rich. This observation has both practical and mechanistic interests. The phase diagrams of these systems were constructed by experimental measurements at ambient conditions. Molecular dynamic (MD) simulations were performed for TES + water + THF system to understand the interactions between TES, water, and organic solvent at molecular level. Several composition-sets for this system, beyond and inside the liquid-liquid phase-splitting region, have been simulated. Interestingly, the MD simulation for compositions inside the phase separation region showed that THF molecules are forced out from the water network to start forming a new liquid phase. The hydrogen-bonds, hydrogen-bonds lifetimes, hydrogen-bond energies, radial distribution functions, coordination numbers, the electrostatic interactions, and the van der Waals interactions between the different pairs have been calculated. Additionally, MD simulations for TES + water + tert-butanol∕acetonitrile∕acetone phase separation systems were simulated. The results from MD simulations provide an explanation for the buffering-out phenomena observed in [TES + water + organic solvent] systems by a mechanism controlled by the competitive interactions of the buffer and the organic solvent with water. The molecular mechanism reported here is helpful for designing new benign separation materials.

Photophysical parameters and fluorescence quenching of 7-diethylaminocoumarin (DEAC) laser dye

NASA Astrophysics Data System (ADS)

El-Mossalamy, E. H.; Obaid, A. Y.; El-Daly, S. A.

2011-10-01

The optical properties including electronic absorption spectrum, emission spectrum, fluorescence quantum yield, and dipole moment of electronic transition of 7-diethylaminocoumarin (DEAC) laser dye have been measured in different solvents. Both electronic absorption and fluorescence spectra are red shifted as the polarity of the medium increases, indicating that the dipole moment of molecule increases on excitation. The fluorescence quantum yield of DEAC decreases as the polarity of solvent increases, a result of the role of solvent polarity in stabilization of the twisting of the intramolecular charge transfer (TICT) in excited state, which is a non-emissive state, as well as hydrogen bonding with the hetero-atom of dye. The emission spectrum of DEAC has also been measured in cationic (CTAC) and anionic (SDS) micelles, the intensity increases as the concentration of surfactant increases, and an abrupt change in emission intensity is observed at critical micelle concentration (CMC) of surfactant. 2×10 -3 mol dm -3 of DEAC gives laser emission in the blue region on pumping with nitrogen laser ( λex=337.1 nm). The laser parameters such as tuning range, gain coefficient ( α), emission cross section ( σe), and half-life energy have been calculated in different solvents, namely acetone, dioxane , ethanol, and dimethyforamide (DMF). The photoreactivity of DEAC has been studied in CCl 4 at a wavelength of 366 nm. The values of photochemical yield ( ϕc) and rate constant ( k) are determined. The interaction of organic acceptors such as picric acid (PA), tetracyanoethylene (TCNE), and 7,7,8,8-tetracynoquinonedimethane (TCNQ) with DEAC is also studied using fluorescence measurements in acetonitrile (CH 3CN); from fluorescence quenching study we assume the possible electron transfer from excited donor DEAC to organic acceptor forming non-emissive exciplex.

Synthesis and molecular docking against dihydrofolate reductase of novel pyridin-N-ethyl-N-methylbenzenesulfonamides as efficient anticancer and antimicrobial agents

NASA Astrophysics Data System (ADS)

Debbabi, Khaled F.; Bashandy, Mahmoud S.; Al-Harbi, Sami A.; Aljuhani, Enas H.; Al-Saidi, Hamed M.

2017-03-01

This article describes the synthesis of some novel sulfonamides having biologically active pyridine 21-28. Starting with 4-(1-(2-(2-cyanoacetyl)hydrazono)ethyl)-N-ethyl-N-methylbenzenesulfonamide (2), which was prepared from condensation of acetophenone derivative 1 with 2-cyanoacetohydrazide. Interaction of compound 2 with different aldehydes namely 4-fluorobenzaldehyde, 4-hydroxybenzaldehyde and 4-N,N-dimethylbenzaldehyde afforded the corresponding hydrazono-ethyl-N-ethyl-N-methylbenzene sulfonamides 18-20 respectively, which when reacted with malononitrile and ethyl cyanoacetate afforded compounds 21-26 respectively. These compounds 21-26 can be prepared by another reaction route by interaction of compounds 2 with arylidine malononitrile and arylidine ethyl cyanoacetate in refluxing dioxane in the presence of trimethylamine as catalyst. Interaction of compound 2 with malononitrile and ethyl cyanoacetate afforded oxopyridine derivatives 27 and 28 respectively. All the new prepared compounds were evaluated for their antitumor activities against the cell lines MCF-7 in comparison with the reference drug Doxorubicin using the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) colorimetric assay. Compounds 25, 21, 23 with SI values of 9.72, 9.71, 8.81 respectively, exhibited better activity than doxorubicin (Dox) as a reference drug with SI value of 8.49. In addition, compounds 25, 27 and 22 exhibited anti-bacterial activity against gram-negative bacteria (Klebsiella pneumoniae) with inhibition zones 22.6, 20.3 and 19.3 mm respectively, which were more active than gentamicin as a reference drug with inhibition zone 17.3 mm. Molecular Operating Environment (MOE) performed virtual screening using molecular docking studies of the synthesized compounds. The results indicated that some synthesized compounds suitable inhibitor against dihydrofolate reductase (DHFR) enzyme (PDB SD: 4DFR) with further modification.

Intramolecular, Exciplex-Mediated, Proton-Coupled, Charge-Transfer Processes in N,N-Dimethyl-3-(1-pyrenyl)propan-1-ammonium Cations: Influence of Anion, Solvent Polarity, and Temperature.

PubMed

Safko, Trevor M; Faleiros, Marcelo M; Atvars, Teresa D Z; Weiss, Richard G

2016-06-16

An intramolecular exciplex-mediated, proton-coupled, charge-transfer (PCCT) process has been investigated for a series of N,N-dimethyl-3-(1-pyrenyl)propan-1-ammonium cations with different anions (PyS) in solvents of low to intermediate polarity over a wide temperature range. Solvent mediates both the equilibrium between conformations of the cation that place the pyrenyl and ammonium groups in proximity (conformation C) or far from each other (conformation O) and the ability of the ammonium group to transfer a proton adiabatically in the PyS excited singlet state. Thus, exciplex emission, concurrent with the PCCT process, was observed only in hydrogen-bond accepting solvents of relatively low polarity (tetrahydrofuran, ethyl acetate, and 1,4-dioxane) and not in dichloromethane. From the exciplex emission and other spectroscopic and thermodynamic data, the acidity of the ammonium group in conformation C of the excited singlet state of PyS (pKa*) has been estimated to be ca. -3.4 in tetrahydrofuran. The ratios between the intensities of emission from the exciplex and the locally excited state (IEx/ILE) appear to be much more dependent on the nature of the anion than are the rates of exciplex formation and decay, although the excited state data do not provide a quantitative measure of the anion effect on the C-O equilibrium. The activation energies associated with exciplex formation in THF are calculated to be 0.08 to 0.15 eV lower than for the neutral amine, N,N-dimethyl-3-(1-pyrenyl)propan-1-amine. Decay of the exciplexes formed from the deprotonation of PyS is hypothesized to occur through charge-recombination processes. To our knowledge, this is the first example in which photoacidity and intramolecular exciplex formation (i.e., a PCCT reaction) are coupled.

Structural anomaly and dynamic heterogeneity in cycloether/water binary mixtures: Signatures from composition dependent dynamic fluorescence measurements and computer simulations

NASA Astrophysics Data System (ADS)

Indra, Sandipa; Guchhait, Biswajit; Biswas, Ranjit

2016-03-01

We have performed steady state UV-visible absorption and time-resolved fluorescence measurements and computer simulations to explore the cosolvent mole fraction induced changes in structural and dynamical properties of water/dioxane (Diox) and water/tetrahydrofuran (THF) binary mixtures. Diox is a quadrupolar solvent whereas THF is a dipolar one although both are cyclic molecules and represent cycloethers. The focus here is on whether these cycloethers can induce stiffening and transition of water H-bond network structure and, if they do, whether such structural modification differentiates the chemical nature (dipolar or quadrupolar) of the cosolvent molecules. Composition dependent measured fluorescence lifetimes and rotation times of a dissolved dipolar solute (Coumarin 153, C153) suggest cycloether mole-fraction (XTHF/Diox) induced structural transition for both of these aqueous binary mixtures in the 0.1 ≤ XTHF/Diox ≤ 0.2 regime with no specific dependence on the chemical nature. Interestingly, absorption measurements reveal stiffening of water H-bond structure in the presence of both the cycloethers at a nearly equal mole-fraction, XTHF/Diox ˜ 0.05. Measurements near the critical solution temperature or concentration indicate no role for the solution criticality on the anomalous structural changes. Evidences for cycloether aggregation at very dilute concentrations have been found. Simulated radial distribution functions reflect abrupt changes in respective peak heights at those mixture compositions around which fluorescence measurements revealed structural transition. Simulated water coordination numbers (for a dissolved C153) and number of H-bonds also exhibit minima around these cosolvent concentrations. In addition, several dynamic heterogeneity parameters have been simulated for both the mixtures to explore the effects of structural transition and chemical nature of cosolvent on heterogeneous dynamics of these systems. Simulated four-point dynamic susceptibility suggests formation of clusters inducing local heterogeneity in the solution structure.

A novel nano-structured porous polycaprolactone scaffold improves hyaline cartilage repair in a rabbit model compared to a collagen type I/III scaffold: in vitro and in vivo studies.

PubMed

Christensen, Bjørn Borsøe; Foldager, Casper Bindzus; Hansen, Ole Møller; Kristiansen, Asger Albæk; Le, Dang Quang Svend; Nielsen, Agnete Desirée; Nygaard, Jens Vinge; Bünger, Cody Erik; Lind, Martin

2012-06-01

To develop a nano-structured porous polycaprolactone (NSP-PCL) scaffold and compare the articular cartilage repair potential with that of a commercially available collagen type I/III (Chondro-Gide) scaffold. By combining rapid prototyping and thermally induced phase separation, the NSP-PCL scaffold was produced for matrix-assisted autologous chondrocyte implantation. Lyophilizing a water-dioxane-PCL solution created micro and nano-pores. In vitro: The scaffolds were seeded with rabbit chondrocytes and cultured in hypoxia for 6 days. qRT-PCR was performed using primers for sox9, aggrecan, collagen type 1 and 2. In vivo: 15 New Zealand White Rabbits received bilateral osteochondral defects in the femoral intercondylar grooves. Autologous chondrocytes were harvested 4 weeks prior to surgery. There were 3 treatment groups: (1) NSP-PCL scaffold without cells. (2) The Chondro-Gide scaffold with autologous chondrocytes and (3) NSP-PCL scaffold with autologous chondrocytes. Observation period was 13 weeks. Histological evaluation was made using the O'Driscoll score. In vitro: The expressions of sox9 and aggrecan were higher in the NSP-PCL scaffold, while expression of collagen 1 was lower compared to the Chondro-Gide scaffold. In vivo: Both NSP-PCL scaffolds with and without cells scored significantly higher than the Chondro-Gide scaffold when looking at the structural integrity and the surface regularity of the repair tissue. No differences were found between the NSP-PCL scaffold with and without cells. The NSP-PCL scaffold demonstrated higher in vitro expression of chondrogenic markers and had higher in vivo histological scores compared to the Chondro-Gide scaffold. The improved chondrocytic differentiation can potentially produce more hyaline cartilage during clinical cartilage repair. It appears to be a suitable cell-free implant for hyaline cartilage repair and could provide a less costly and more effective treatment option than the Chondro-Gide scaffold with cells.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Wen-Hua; Yan, Hao-Jie; Chen, Hui

Dipyridyl sulphide ligands 4-(pyridin-4-ylmethylthio)pyridine (abbreviated as L1) and 3-(pyridin-4-ylmethylthio)pyridine (abbreviated as L2) have been designed and used as μ-{sub N},{sub N}-bridging linkages to construct coordination polymers with free –S–CH{sub 2}– groups as secondary donor sites. By use solvent control method, coordination polymers ([Ag{sub 3}SO{sub 4}(L1){sub 3}](Cl)·4.5H{sub 2}O){sub ∞}(1), ([Ag{sub 2}SO{sub 4}(L1){sub 2}]·6H{sub 2}O·2CH{sub 3}OH){sub ∞}(2), ([Ag{sub 2}SO{sub 4}(L2){sub 2}]·H{sub 2}O){sub ∞}(3) and ([Ag{sub 4}(SO{sub 4}){sub 2}(L2){sub 4}]·5H{sub 2}O){sub ∞}(4) with different architectures were obtained. Complexes 1, 3 and 4 feature 1D channel with different sizes and structures. Complex 1 exhibits guest exchange by THF and 1,4-dioxane, and Hg{sup 2+} sorptionmore » ability from solution due to its relative larger channel and available bonding sites of –S– exposed to the channel region. All complexes have been characterized through single-crystal and powder X-ray diffraction (PXRD), FT-IR spectra, X-ray photoelectron spectroscopy (XPS), elemental and thermogravimetric analyses. The guest exchange and Hg{sup 2+} sorption were monitored and identified, and the structure-property relationship of coordination polymers 1–4 are discussed. - Graphical abstract: Coordination polymers of silver(I) sulfate with secondary donor sites are shown guest exchange property and Hg{sup 2+} absorb ability from solution. This work provides a new method to construct functional materials with potential application. - Highlights: • New example of constructing functional coordination polymer with secondary donor methylthio group. • Guest exchange and interesting Hg(II) absorb ability from solution are investigated. • New method to construct functional materials with potential application.« less

Cationic aza-macrocyclic complexes of germanium(II) and silicon(IV).

PubMed

Everett, Matthew; Jolleys, Andrew; Levason, William; Light, Mark E; Pugh, David; Reid, Gillian

2015-12-28

[GeCl2(dioxane)] reacts with the neutral aza-macrocyclic ligands L, L = Me3tacn (1,4,7-trimethyl-1,4,7-triazacyclononane), Me4cyclen (1,4,7,10-tetramethyl-1,4,7,10-tetraazacyclododecane) or Me4cyclam (1,4,8,11-tetramethyl-1,4,8,11-tetraazacyclotetradecane) and two mol. equiv. of Me3SiO3SCF3 in thf solution to yield the unusual and hydrolytically very sensitive [Ge(L)][O3SCF3]2 as white solids in moderate yield. Using shorter reaction times [Ge(Me3tacn)]Cl2 and [Ge(Me3tacn)]Cl[O3SCF3] were also isolated; the preparation of [Ge(Me4cyclen)][GeCl3]2 is also described. The structures of the Me3tacn complexes show κ(3)-coordination of the macrocycle, with the anions interacting only weakly to produce very distorted five- or six-coordination at germanium. In contrast, the structure of [Ge(Me4cyclen)][O3SCF3]2 shows no anion interactions, and a distorted square planar geometry at germanium from coordination to the tetra-aza macrocycle. Crystal structures of the Si(iv) complexes, [SiCl3(Me3tacn)]Y (Y = O3SCF3, BAr(F); [B{3,5-(CF3)2C6H3}4]) and [SiHCl2(Me3tacn)][BAr(F)], obtained from reaction of SiCl4 or SiHCl3 with Me3tacn, followed by addition of either Me3SiO3SCF3 or Na[BAr(F)], contain distorted octahedral cations, with facialκ(3)-coordinated Me3tacn. The open-chain triamine, Me2NCH2CH2N(Me)CH2CH2NMe2 (pmdta), forms [SiCl3(pmdta)][BAr(F)] and [SiBr3(pmdta)][BAr(F)] under similar conditions, containing mer-octahedral cations.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bisht, Kamal Kumar; Rachuri, Yadagiri; Academy of Scientific and Innovative Research

Four ternary coordination polymers (CPs) namely, ([Ni(SDB)(BITMB)(H{sub 2}O)]·H{sub 2}O){sub n} (CP1), ([Cd(SDB)(BITMB) (H{sub 2}O)]·(THF)(H{sub 2}O)){sub n} (CP2), ([Zn{sub 2}(SDB){sub 2}(BITMB)]·(THF){sub 2}){sub n} (CP3) and ([Co{sub 2}(SDB){sub 2}(BITMB)]·(Dioxane){sub 3}){sub n} (CP4) composed of angular dicarboxylate SDB (4,4'-sulfonyldibenzoate) and N-donor BITMB (1,3-bis(imidazol-1-ylmethyl)-2,4,6-trimethyl benzene) have been synthesized by solvothermal reactions and characterized by single crystal X-ray diffraction and other physico-chemical techniques. CP1 possesses one-dimensional ribbon type metal–organic motifs glued together by H-bonds and π⋯π interactions, whereas CP2–CP4, exhibit non-interpenetrated sql networks supported by weak supramolecular interactions. Structural diversity of these CPs can be attributed to the coordination geometry adopted by the metal nodes,more » versatile coordination modes of SDB and conformational flexibility of BITMB. Solid state luminescence properties of CP1–CP4 were explored. Photocatalytic performance of all CPs for the decomposition of metanil yellow by dilute hydrogen peroxide in the presence of visible light was also investigated. 25–83% dye removal from aqueous solutions in the presence of CP1–CP4 was observed. - Graphical abstract: Four new ternary transition metal CPs have been hydrothermally prepared and their structural aspects as well as photocatalytic activity for decolourization of metanil yellow (MY) dye have been investigated. - Highlights: • Four ternary coordination polymers containing Ni, Cd, Zn and Co center are prepared. • Crystal structure and thermal stability of all four CPs has been described. • PL and diffuse reflectance spectra of synthesized CPs have also been examined. • Band gap values suggest semiconducting behavior of prepared CPs. • Photocatalytic activity of CPs for oxidative degradation of metanil yellow is studied.« less

Synthesis and cytotoxic activity of some 17-picolyl and 17-picolinylidene androstane derivatives.

PubMed

Djurendić, Evgenija A; Ajduković, Jovana J; Sakač, Marija N; Csanádi, János J; Kojić, Vesna V; Bogdanović, Gordana M; Penov Gaši, Katarina M

2012-08-01

New 17-picolyl and 17-picolinylidene androstane derivatives, 3-10, 15, 18, 19, 22 and 23, were synthesized starting from 17α-picolyl-androst-5-en-3β,17β-diol (1) and 17(Z)-picolinylidene-androst-5-en-3β-ol (2). Reaction of 1 with m-chloroperoxybenzoic acid gives 5α,6α-epoxy N-oxide derivative 3, or, with Jones reagent, 3,6-dione derivative 4; while 17α-picolyl-androst-5-en-3β,4α,17β-triol (5) or 3β,4β,17β-triol (6) derivatives are obtainable from 1 using SeO(2) in dioxane. Base-catalyzed tosyl group elimination from 7 or 9 affords AB conjugated derivatives 8 and 10. Oppenauer oxidation of 1 and 2 yields 4-en-3-one derivatives 11 and 12, which, with H(2)O(2) in 4 M NaOH, affords 4α,5α and 4β,5β-epoxides 13, 14, 16 and 17. New 4-methoxy-3-keto derivatives 15 and 18 were obtained from 13 and 14, or, with methanol in 4 M NaOH, from 16 and 17. Reduction of 11 with NaBH(4) gives 22, which was then acetylated to obtain 23. All new derivatives were screened for antitumor activity against human breast adenocarcinoma ER+, MCF-7; human breast adenocarcinoma ER-, MDA-MB-231; prostate cancer AR-, PC-3; human cervix carcinoma, HeLa; and colon cancer, HT-29 cells; as well as one human non-tumor cell line, MRC-5. Compounds 3, 5, 6, 8, 10, 18, 19 and 22 exhibited significant antitumor activity against MDA-MB-231 breast cancer cells; while 5, 6 and 10 also showed strong cytotoxicity against HT-29. Only compound 19 exhibited significant activity against MCF-7 breast cancer cells. No compounds displayed cytotoxicity against non-tumor MRC-5 cells. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

Phytoremediation of ethylene glycol and its derivatives by the burhead plant (Echinodorus cordifolius (L.)): effect of molecular size.

PubMed

Teamkao, Pattrarat; Thiravetyan, Paitip

2010-11-01

Ethylene glycol (EG) is a group of dihydroxy alcohol that has been utilised in a variety of industrial and residential settings. EG contaminated wastewater has a high chemical oxygen demand (COD), which causes environmental problems. The aim of this research was to investigate the efficiency of the burhead plant (Echinodorus cordifolius (L.)) in the removal of mono-, di- and triethylene glycol (MEG, DEG and TEG), the first three members of the dihydroxy alcohol group, from synthetic wastewaters, to examine the toxic effect of EG on the plant and to identify differences among MEG, DEG, and TEG removal. It was found that the COD of synthetic wastewaters decreased to levels below the standard effluent (COD=120 mg L⁻¹) on day 18, 21 and 33 for MEG, DEG and TEG, respectively. On day 18 of the experiment, the burhead plant removed approximately 2000, 1950 and 730 mg L⁻¹ of MEG, DEG and TEG, respectively. The removal rate of MEG was faster than that of DEG and TEG, suggesting that the molecular size of the EG had affected its rate of removal. The concentrations of MEG, DEG, and TEG in plant tissue were measured to show that burhead can take up EG, and the major site of EG accumulation is the leaf. The molar of MEG that was taken up into the plant leaf was higher than that of DEG and TEG. This suggested that EG of smaller molecular sizes can be taken up more rapidly by the plant than EG of larger molecular sizes. EG concentrations in the leaf increased to a peak concentration and then slowly decreased. GC-MS analysis of DEG-treated plant tissue found MEG, 1,4-dioxan-2-one, neophytadiene, and 2-propenamide, that may be DEG-degradation products and/or compounds that are induced when plants are exposed to DEG. The result indicates that burhead can potentially be used for EG removal. Copyright © 2010 Elsevier Ltd. All rights reserved.

Millimeter wave and terahertz dielectric properties of biological materials

NASA Astrophysics Data System (ADS)

Khan, Usman Ansar

Broadband dielectric properties of materials can be employed to identify, detect, and characterize materials through their unique spectral signatures. In this study, millimeter wave, submillimeter wave, and terahertz dielectric properties of biological substances inclusive of liquids, solids, and powders were obtained using Dispersive Fourier Transform Spectroscopy (DFTS). Two broadband polarizing interferometers were constructed to test materials from 60 GHz to 1.2 THz. This is an extremely difficult portion of the frequency spectrum to obtain a material's dielectric properties since neither optical nor microwave-based techniques provide accurate data. The dielectric characteristics of liquids such as cyclohexane, chlorobenzene, benzene, ethanol, methanol, 1,4 dioxane, and 10% formalin were obtained using the liquid interferometer. Subsequently the solid interferometer was utilized to determine the dielectric properties of human breast tissues, which are fixed and preserved in 10% formalin. This joint collaboration with the Tufts New England Medical Center demonstrated a significant difference between the dielectric response of tumorous and non-tumorous breast tissues across the spectrum. Powders such as anthrax, flour, talc, corn starch, dry milk, and baking soda have been involved in a number of security threats and false alarms around the globe in the last decade. To be able to differentiate hoax attacks and serious security threats, the dielectric properties of common household powders were also examined using the solid interferometer to identify the powders' unique resonance peaks. A new sample preparation kit was designed to test the powder specimens. It was anticipated that millimeter wave and terahertz dielectric characterization will enable one to clearly distinguish one powder from the other; however most of the powders had relatively close dielectric responses and only Talc had a resonance signature recorded at 1.135 THz. Furthermore, due to polarization and birefringence effects, it was determined that one can not utilize the dielectric properties of powder-containing packages to differentiate hoax attacks and serious security threats.

GABAA receptors involved in sleep and anaesthesia: β1- versus β3-containing assemblies.

PubMed

Yanovsky, Yevgenij; Schubring, Stephan; Fleischer, Wiebke; Gisselmann, Günter; Zhu, Xin-Ran; Lübbert, Hermann; Hatt, Hanns; Rudolph, Uwe; Haas, Helmut L; Sergeeva, Olga A

2012-01-01

The histaminergic neurons of the posterior hypothalamus (tuberomamillary nucleus-TMN) control wakefulness, and their silencing through activation of GABA(A) receptors (GABA(A)R) induces sleep and is thought to mediate sedation under propofol anaesthesia. We have previously shown that the β1 subunit preferring fragrant dioxane derivatives (FDD) are highly potent modulators of GABA(A)R in TMN neurons. In recombinant receptors containing the β3N265M subunit, FDD action is abolished and GABA potency is reduced. Using rat, wild-type and β3N265M mice, FDD and propofol, we explored the relative contributions of β1- and β3-containing GABA(A)R to synaptic transmission from the GABAergic sleep-on ventrolateral preoptic area neurons to TMN. In β3N265M mice, GABA potency remained unchanged in TMN neurons, but it was decreased in cultured posterior hypothalamic neurons with impaired modulation of GABA(A)R by propofol. Spontaneous and evoked GABAergic synaptic currents (IPSC) showed β1-type pharmacology, with the same effects achieved by 3 μM propofol and 10 μM PI24513. Propofol and the FDD PI24513 suppressed neuronal firing in the majority of neurons at 5 and 100 μM, and in all cells at 10 and 250 μM, respectively. FDD given systemically in mice induced sedation but not anaesthesia. Propofol-induced currents were abolished (1-6 μM) or significantly reduced (12 μM) in β3N265M mice, whereas gating and modulation of GABA(A)R by PI24513 as well as modulation by propofol were unchanged. In conclusion, β1-containing (FDD-sensitive) GABA(A)R represent the major receptor pool in TMN neurons responding to GABA, while β3-containing (FDD-insensitive) receptors are gated by low micromolar doses of propofol. Thus, sleep and anaesthesia depend on different GABA(A)R types.

Tocopherol and tocotrienol homologs in parenteral lipid emulsions

PubMed Central

Xu, Zhidong; Harvey, Kevin A; Pavlina, Thomas M; Zaloga, Gary P; Siddiqui, Rafat A

2015-01-01

Parenteral lipid emulsions, which are made of oils from plant and fish sources, contain different types of tocopherols and tocotrienols (vitamin E homologs). The amount and types of vitamin E homologs in various lipid emulsions vary considerably and are not completely known. The objective of this analysis was to develop a quantitative method to determine levels of all vitamin E homologs in various lipid emulsions. An HPLC system was used to measure vitamin E homologs using a Pinnacle DB Silica normal phase column and an isocratic, n-hexane:1,4 dioxane (98:2) mobile phase. An optimized protocol was used to report vitamin E homolog concentrations in soybean oil-based (Intralipid®, Ivelip®, Lipofundin® N, Liposyn® III, and Liposyn® II), medium- and long-chain fatty acid-based (Lipofundin®, MCT and Structolipid®), olive oil-based (ClinOleic®), and fish oil-based (Omegaven®) and mixture of these oils-based (SMOFlipid®, Lipidem®) commercial parenteral lipid emulsions. Total content of all vitamin E homologs varied greatly between different emulsions, ranging from 57.9 to 383.9 µg/mL. Tocopherols (α, β, γ, δ) were the predominant vitamin E homologs for all emulsions, with tocotrienol content < 0.3%. In all of the soybean emulsions, except for Lipofundin® N, the predominant vitamin E homolog was γ-tocopherol, which ranged from 57–156 µg/mL. ClinOleic® predominantly contained α-tocopherol (32 µg/mL), whereas α-tocopherol content in Omegaven® was higher than most of the other lipid emulsions (230 µg/mL). Practical applications The information on the types and quantity of vitamin E homologs in various lipid emulsions will be extremely useful to physicians and healthcare personnel in selecting appropriate lipid emulsions that are exclusively used in patients with inadequate gastrointestinal function, including hospitalized and critically ill patients. Some emulsions may require vitamin E supplementation in order to meet minimal human requirements. PMID:25685054

Screening for Groundwater Contaminants Discharging to Urban Streams

NASA Astrophysics Data System (ADS)

Roy, J. W.; Bickerton, G.; Voralek, J.

2009-05-01

Groundwater contaminated with urban pollutants can adversely affect freshwater aquatic ecosystems where it discharges to streams, lakes or wetlands. Generally such occurrences have been revealed following the discovery of contaminated groundwater plumes at a particular site or from wells in the area. Thus, this contaminant pathway tends to be dealt with on a site-specific and aquifer-focused basis. In contrast, surface water contaminant monitoring typically relies on bulk water concentrations from one or a small set of locations, thus ignoring the spatial variation in contaminant loading, potential losses to sediment or the atmosphere, and the full range of benthic components of the aquatic ecosystem. There are few studies outlining the extent of this contamination from the perspective of the surface water body's deeper benthic community, which might be expected to experience the greatest contaminant concentrations, on more than a local-scale. In this study, we report on an approach to stream-reach-screening for urban contaminants in discharging groundwater, with the focus on detection rather than accurate quantification. The methodology consists of a drive-point technique for sampling groundwater from below the stream bed (e.g. typically 50 cm) along a chosen reach at intervals of about 10 m. Groundwater samples were then analyzed for a wide range of common urban contaminants and general chemistry. This screening method was performed in three urban settings in Canada with known groundwater contamination, covering sections of about 140 to >500 m. The known contaminant plumes at each site were detected and roughly delineated. In addition, potential areas of previously-unknown groundwater contamination were also identified at each site. Contaminants included BTEX and other petroleum hydrocarbons, various chlorinated solvent compounds, nitrate, 1,4-dioxane, MTBE and elevated chloride (likely indicating road salt). These preliminary findings suggest that this approach may be useful for quickly assessing the cumulative threat to aquatic ecosystems of potentially multiple groundwater contaminant sources discharging to surface water bodies in urban settings.

Candida antartica lipase B catalyzed polycaprolactone synthesis: effects of organic media and temperature.

PubMed

Kumar, A; Gross, R A

2000-01-01

Engineering of the reaction medium and study of an expanded range of reaction temperatures were carried out in an effort to positively influence the outcome of Novozyme-435 (immobilized Lipase B from Candida antarctica) catalyzed epsilon-CL polymerizations. A series of solvents including acetonitrile, dioxane, tetrahydrofuran, chloroform, butyl ether, isopropyl ether, isooctane, and toluene (log P from -1.1 to 4.5) were evaluated at 70 degrees C. Statistically (ANOVA), two significant regions were observed. Solvents having log P values from -1.1 to 0.49 showed low propagation rates (< or = 30% epsilon-CL conversion in 4 h) and gave products of short chain length (Mn < or = 5200 g/mol). In contrast, solvents with log P values from 1.9 to 4.5 showed enhanced propagation rates and afforded polymers of higher molecular weight (Mn = 11,500-17,000 g/mol). Toluene, a preferred solvent for this work, was studied at epsilon-CL to toluene (wt/vol) ratios from 1:1 to 10:1. The ratio 1:2 was selected since, for polymerizations at 70 degrees C, 0.3 mL of epsilon-CL and 4 h, gave high monomer conversions and Mn values (approximately 85% and approximately 17,000 g/mol, respectively). Increasing the scale of the reaction from 0.3 to 10 mL of CL resulted in a similar isolated product yield, but the Mn increased from 17,200 to 44,800 g/mol. Toluene appeared to help stabilize Novozyme-435 so that lipase-catalyzed polymerizations could be conducted effectively at 90 degrees C. For example, within only 2 h at 90 degrees C (toluene-d8 to epsilon-CL, 5:1, approximately 1% protein), the % monomer conversion reached approximately 90%. Also, the controlled character of these polymerizations as a function of reaction temperature was evaluated.

A Systematic Approach to Evaluate Herb-Drug Interaction Mechanisms: Investigation of Milk Thistle Extracts and Eight Isolated Constituents as CYP3A Inhibitors

PubMed Central

Brantley, Scott J.; Graf, Tyler N.; Oberlies, Nicholas H.

2013-01-01

Despite increasing recognition of potential untoward interactions between herbal products and conventional medications, a standard system for prospective assessment of these interactions remains elusive. This information gap was addressed by evaluating the drug interaction liability of the model herbal product milk thistle (Silybum marianum) with the CYP3A probe substrate midazolam. The inhibitory effects of commercially available milk thistle extracts and isolated constituents on midazolam 1′-hydroxylation were screened using human liver and intestinal microsomes. Relative to vehicle, the extract silymarin and constituents silybin A, isosilybin A, isosilybin B, and silychristin at 100 μM demonstrated >50% inhibition of CYP3A activity with at least one microsomal preparation, prompting IC50 determination. The IC50s for isosilybin B and silychristin were ∼60 and 90 μM, respectively, whereas those for the remaining constituents were >100 μM. Extracts and constituents that contained the 1,4-dioxane moiety demonstrated a >1.5-fold shift in IC50 when tested as potential mechanism-based inhibitors. The semipurified extract, silibinin, and the two associated constituents (silybin A and silybin B) demonstrated mechanism-based inhibition of recombinant CYP3A4 (KI, ∼100 μM; kinact, ∼0.20 min−1) but not microsomal CYP3A activity. The maximum predicted increases in midazolam area under the curve using the static mechanistic equation and recombinant CYP3A4 data were 1.75-fold, which may necessitate clinical assessment. Evaluation of the interaction liability of single herbal product constituents, in addition to commercially available extracts, will enable elucidation of mechanisms underlying potential clinically significant herb-drug interactions. Application of this framework to other herbal products would permit predictions of herb-drug interactions and assist in prioritizing clinical evaluation. PMID:23801821

A systematic approach to evaluate herb-drug interaction mechanisms: investigation of milk thistle extracts and eight isolated constituents as CYP3A inhibitors.

PubMed

Brantley, Scott J; Graf, Tyler N; Oberlies, Nicholas H; Paine, Mary F

2013-09-01

Despite increasing recognition of potential untoward interactions between herbal products and conventional medications, a standard system for prospective assessment of these interactions remains elusive. This information gap was addressed by evaluating the drug interaction liability of the model herbal product milk thistle (Silybum marianum) with the CYP3A probe substrate midazolam. The inhibitory effects of commercially available milk thistle extracts and isolated constituents on midazolam 1'-hydroxylation were screened using human liver and intestinal microsomes. Relative to vehicle, the extract silymarin and constituents silybin A, isosilybin A, isosilybin B, and silychristin at 100 μM demonstrated >50% inhibition of CYP3A activity with at least one microsomal preparation, prompting IC50 determination. The IC50s for isosilybin B and silychristin were ∼60 and 90 μM, respectively, whereas those for the remaining constituents were >100 μM. Extracts and constituents that contained the 1,4-dioxane moiety demonstrated a >1.5-fold shift in IC50 when tested as potential mechanism-based inhibitors. The semipurified extract, silibinin, and the two associated constituents (silybin A and silybin B) demonstrated mechanism-based inhibition of recombinant CYP3A4 (KI, ∼100 μM; kinact, ∼0.20 min(-1)) but not microsomal CYP3A activity. The maximum predicted increases in midazolam area under the curve using the static mechanistic equation and recombinant CYP3A4 data were 1.75-fold, which may necessitate clinical assessment. Evaluation of the interaction liability of single herbal product constituents, in addition to commercially available extracts, will enable elucidation of mechanisms underlying potential clinically significant herb-drug interactions. Application of this framework to other herbal products would permit predictions of herb-drug interactions and assist in prioritizing clinical evaluation.

Synthesis of ST7612AA1, a Novel Oral HDAC Inhibitor, via Radical 
Thioacetic Acid Addition.

PubMed

Battistuzzi, Gianfranco; Giannini, Giuseppe

2016-12-01

In the expanding field of anticancer drugs, HDAC inhibitors are playing an increasingly important role. To date, four/five HDAC inhibitors have been approved by FDA. All these compounds fit the widely accepted HDAC inhibitors pharmacophore model characterized by a cap group, a linker chain and a zinc binding group (ZBG), able to bind the Zn 2+ ion in a pocket of the HDAC active site. Romidepsin, a natural compound, is the only thiol derivative. We have selected a new class of synthetic HDAC inhibitors, the thio-ω(lactam-carboxamide) derivatives, with ST7612AA1 as drug candidate, pan-inhibitor active in the range of single- to two-digit nanomolar concentrations. Preliminary results of a synthetic optimization attempt towards a fast scale-up process are here proposed. In the four steps of synthesis, from unsaturated amino acid intermediate to the final product, we explored different synthetic conditions in order to have a transferable process for a scale-up synthetic laboratory. In the first step, isobutyl chloroformate was used and, after a simple work up with 1M HCl, 2 (96% yield) was obtained as a white solid, which was used directly in the next step. For thioacetic acid addition to the double bond of intermediate 2 , two different routes were possible, with addition reaction in the first (D') or last step (D). Reactions of 2 to give 5 or of 4 to give ST7612AA1 were both performed in dioxane. Reactions were fast and did not need the usually advised radical quenching with cyclohexene. The corresponding products were obtained in good yields (step D', 89%; step D, 81%) after a flash chromatography. , a thiol derivative prodrug of ST7464AA1 , is the first of a new generation of HDAC inhibitors, very potent, orally administered, and well tolerated. Here, we have identified a synthetic route, competitive, versatile and easily transferable to industrial processes.

Polymersomes from dual responsive block copolymers: drug encapsulation by heating and acid-triggered release.

PubMed

Qiao, Zeng-Ying; Ji, Ran; Huang, Xiao-Nan; Du, Fu-Sheng; Zhang, Rui; Liang, De-Hai; Li, Zi-Chen

2013-05-13

A series of well-defined thermoresponsive diblock copolymers (PEO45-b-PtNEAn, n=22, 44, 63, 91, 172) were prepared by the atom transfer radical polymerization of trans-N-(2-ethoxy-1,3-dioxan-5-yl) acrylamide (tNEA) using a poly(ethylene oxide) (PEO45) macroinitiator. All copolymers are water-soluble at low temperature, but upon quickly heating to 37 °C, laser light scattering (LLS) and transmission electron microscopy (TEM) characterizations indicate that these copolymers self-assemble into aggregates with different morphologies depending on the chain length of PtNEA and the polymer concentration; the morphologies gradually evolved from spherical solid nanoparticles to a polymersome as the degree of polymerization ("n") of PtNEA block increased from 22 to 172, with the formation of clusters with rod-like structure at the intermediate PtNEA length. Both the spherical nanoparticle and the polymersome are stable at physiological pH but susceptible to the mildly acidic medium. Acid-triggered hydrolysis behaviors of the aggregates were investigated by LLS, Nile red fluorescence, TEM, and (1)H NMR spectroscopy. The results revealed that the spherical nanoparticles formed from PEO45-b-PtNEA44 dissociated faster than the polymersomes of PEO45-b-PtNEA172, and both aggregates showed an enhanced hydrolysis under acidic conditions. Both the spherical nanoparticle and polymersome are able to efficiently load the hydrophobic doxorubicin (DOX), and water-soluble fluorescein isothiocyanate-lysozyme (FITC-Lys) can be conveniently encapsulated into the polymersome without using any organic solvent. Moreover, FITC-Lys and DOX could be coloaded in the polymersome. The drugs loaded either in the polymersome or in the spherical nanoparticle could be released by acid triggering. Finally, the DOX-loaded assemblies display concentration-dependent cytotoxicity to HepG2 cells, while the copolymers themselves are nontoxic.

Quantitative evaluation of inhibitory effect of various substances on anaerobic ammonia oxidation (anammox).

PubMed

Nakamura, Tomotaka; Harigaya, Yuhki; Kimura, Yuya; Kuroiwa, Megumi; Kurata, Yuhri; Isaka, Kazuichi; Suwa, Yuichi

2017-09-01

The inhibitory effect of 20 substances of various chemical species on the anaerobic ammonia oxidation (anammox) activity of an enrichment culture, predominated by Candidatus Brocadia, was determined systematically by using a 15 N tracer technique. The initial anammox rate was determined during first 25 min with a small-scale anaerobic batch incubation supplemented with possible inhibitors. Although Cu 2+ and Mn 2+ did not inhibit anammox, the remaining 18 substances [Ni 2+ , Zn 2+ , Co 2+ , [Formula: see text] , Fe 2+ , 4 amines, ethylenediaminetetraacetic acid (EDTA), ethylenediamine-N,N'-bis (2-hydroxyphenylacetic acid) (EDDHA), citric acid, nitrilotriacetic acid (NTA), N,N-dimethylacetamide (DMA), 1,4-dioxane, dimethyl sulfoxide (DMSO), N,N-dimethylformamide (DMF) and tetrahydrofuran (THF)] were inhibitory. Inhibitory effect of NTA, EDDHA, THF, DMF, DMA and amines on anammox was first determined in this study. Inhibitory effects of metals were re-evaluated because chelators, which may interfere inhibitory effect, have been used to dissolve metal salts into assay solution. The relative anammox activities as a function of concentration of each substance were described successfully (R 2  > 0.91) either with a linear inhibition model or with a Michaelis-Menten-based inhibition model. IC 50 values were estimated based on either model, and were compared. The IC 50 values of the 4 chelators (0.06-2.7 mM) and 5 metal ions (0.02-1.09 mM) were significantly lower than those of the 4 amines (10.6-29.1 mM) and 5 organic solvents (3.5-82 mM). Although it did not show any inhibition within 25 min, 0.1 mM Cu 2+ completely inhibited anammox activity in 240 min, suggesting that the inhibitory effect caused by Cu 2+ is time-dependent. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Status of groundwater quality in the Coastal Los Angeles Basin, 2006-California GAMA Priority Basin Project

USGS Publications Warehouse

Goldrath, Dara; Fram, Miranda S.; Land, Michael; Belitz, Kenneth

2012-01-01

Groundwater quality in the approximately 860-square-mile (2,227-square-kilometer) Coastal Los Angeles Basin study unit (CLAB) was investigated as part of the Priority Basin Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The study area is located in southern California in Los Angeles and Orange Counties. The GAMA Priority Basin Project is being conducted by the California State Water Resources Control Board in collaboration with the U.S. Geological Survey (USGS) and the Lawrence Livermore National Laboratory. The GAMA CLAB study was designed to provide a spatially unbiased assessment of the quality of untreated (raw) groundwater in the primary aquifer system. The assessment is based on water-quality and ancillary data collected in 2006 by the USGS from 69 wells and on water-quality data from the California Department of Public Health (CDPH) database. The primary aquifer system was defined by the depth interval of the wells listed in the CDPH database for the CLAB study unit. The quality of groundwater in the primary aquifer system may be different from that in the shallower or deeper water-bearing zones; shallow groundwater may be more vulnerable to surficial contamination. This study assesses the status of the current quality of the groundwater resource by using data from samples analyzed for volatile organic compounds (VOCs), pesticides, and naturally occurring inorganic constituents, such as major ions and trace elements. This status assessment is intended to characterize the quality of groundwater resources in the primary aquifer system of the CLAB study unit, not the treated drinking water delivered to consumers by water purveyors. Relative-concentrations (sample concentration divided by the health- or aesthetic-based benchmark concentration) were used for evaluating groundwater quality for those constituents that have Federal and (or) California regulatory or non-regulatory benchmarks for drinking-water quality. A relative-concentration greater than (>) 1.0 indicates a concentration greater than a benchmark, and a relative-concentration less than or equal to (≤) 1.0 indicates a concentration equal to or less than a benchmark. Relative-concentrations of organic and special-interest constituents [perchlorate, N-nitrosodimethylamine (NDMA), 1,2,3-trichloropropane (1,2,3-TCP), and 1,4-dioxane] were classified as "high" (relative-concentration>1.0), "moderate" (0.5status assessment for evaluating regional-scale groundwater quality. High aquifer-scale proportion is defined as the percentage of the area of the primary aquifer system with a relative-concentration greater than 1.0 for a particular constituent or class of constituents; percentage is based on an areal rather than a volumetric basis. Moderate and low aquifer-scale proportions were defined as the percentage of the primary aquifer system with moderate and low relative-concentrations, respectively. Two statistical approaches-grid-based and spatially weighted-were used to evaluate aquifer-scale proportions for individual constituents and classes of constituents. Grid-based and spatially weighted estimates were comparable in the CLAB study unit (within 90-percent confidence intervals). Inorganic constituents with human-health benchmarks were detected at high relative-concentrations in 5.6 percent of the primary aquifer system and moderate in 26 percent. High aquifer-scale proportion of inorganic constituents primarily reflected high aquifer-scale proportions of arsenic (1.9 percent), nitrate (1.9 percent), and uranium (1.2 percent). Inorganic constituents with secondary maximum contaminant levels (SMCL) were detected at high relative-concentrations in 18 percent of the primary aquifer system and moderate in 47 percent. The constituents present at high relative-concentrations included total dissolved solids (1.9 percent), manganese (15 percent), and iron (9.4 percent). Relative-concentrations of organic constituents (one or more) were high in 3.7 percent, and moderate in 13 percent, of the primary aquifer system. The high aquifer-scale proportion of organic constituents primarily reflected high aquifer-scale proportions of solvents, including trichloroethene (TCE; 1.7 percent), perchloroethene (PCE; 1.1 percent), and carbon tetrachloride (1.0 percent). Of the 204 organic constituents analyzed, 44 constituents were detected. Eleven organic constituents had detection frequencies of greater than 10 percent: the trihalomethanes chloroform and bromodichloromethane, the solvents TCE, PCE, cis-1,2-dichloroethene, and 1,1-dichloroethene, the herbicides atrazine, simazine, prometon, and tebuthiuron, and the gasoline additive methyl tert-butyl ether (MTBE). Most detections were at low relative-concentrations. The special-interest constituent perchlorate was detected at high relative-concentrations in 0.5 percent of the primary aquifer system, and at moderate relative-concentrations in 35 percent. The special-interest constituent 1,4-dioxane was detected at high relative-concentrations, but an insufficient number of samples was analyzed to provide a representative estimate of aquifer-scale proportion.

A structured understanding of cellobiohydrolase I binding to poplar lignin fractions after dilute acid pretreatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yao, Lan; Yoo, Chang Geun; Meng, Xianzhi

Background: Cellulase adsorption to lignin is considered a cost barrier for bioethanol production; however, its detailed association mechanism is still not fully understood. In this study, two natural poplar variants with high and low sugar release performance were selected as the low and high recalcitrant raw materials (named L and H, respectively). Three different lignin fractions were extracted using ethanol, followed by p-dioxane and then cellulase treatment from the dilute acid pretreated poplar solids (fraction 1, 2, and 3, respectively).Results: Each lignin fraction had different physicochemical properties. Ethanol-extracted lignin had the lowest weight average molecular weight, while the molecular weightsmore » for the other two lignin fractions were similar. 31P NMR analysis revealed that lignin fraction with higher molecular weight contained more aliphatic hydroxyl groups and less phenolic hydroxyl groups. Semi-quantitative analysis by 2D HSQC NMR indicated that the lignin fractions isolated from the natural variants had different contents of syringyl (S), guaiacyl (G) and interunit linkages. Lignin extracted by ethanol contained the largest amount of S units, the smallest amounts of G and p-hydroxybenzoate (PB) subunits, while the contents of these lignin subunits in the other two lignin fractions were similar. The lignin fraction obtained after cellulase treatment was primarily comprised of β-O-4 linkages with small amounts of β-5 and β–β linkages. The binding strength of these three lignin fractions obtained by Langmuir equations were in the order of L1 > L3 > L2 for the low recalcitrance poplar and H1 > H2 > H3 for the high recalcitrance poplar.Conclusions: Overall, adsorption ability of lignin was correlated with the sugar release of poplar. Structural features of lignin were associated with its binding to CBH. For natural poplar variants, lignin fractions with lower molecular weight and polydispersity index (PDI) exhibited more CBH adsorption ability. Lignins with more phenolic hydroxyl groups had higher CBH binding strength. It was also found that lignin fractions with more condensed aromatics adsorbed more CBH likely attributed to stronger hydrophobic interactions.« less

A strategy to improve serum-tolerant transfection activity of polycation vectors by surface hydroxylation.

PubMed

Luo, Xiao-hua; Huang, Fu-wei; Qin, Si-yong; Wang, Hua-fen; Feng, Jun; Zhang, Xian-zheng; Zhuo, Ren-xi

2011-12-01

The aim of this contribution is to develop a universal method to promote the serum-tolerant capability of polycation-based gene delivery system. A "hydroxylation camouflage" strategy was put forward by coating the polycation vectors with hydroxyl-enriched "skin". Branched polyethyleneimine (PEI) was herein used as the polycation model and modified via the catalyst-free aminolysis reaction with 5-ethyl-5-(hydroxymethyl)-1,3-dioxan-2-oxo (EHDO). PEI-g-EHDO, PEI and alkylated PEI derivative termed as PEI-g-DPA were comparatively explored with respect to the transfection efficiency in the serum-free and serum-conditioned medium. The resultant data indicate that the serum-tolerant capability largely depended on the surface composition and substitution degree. In addition to the reduced surface charge, the introduced function caused by hydroxyl coating is believed to play a crucial role for the improved properties of PEI-g-EHDOs. The EHDO modification can effectively inhibit the adsorption of BSA proteins onto polyplexes surface. And the polyplexes stability was remarkably enhanced in the presence of DNase and heparin after EHDO modification. Note that the transfection activity of PEI-g-EHDO(34.5%) in the serum-conditioned medium was even higher than that without serum addition. In contrast, serum addition led to appreciable reduction in the transfection efficiency mediated by PEI and PEI-g-DPAs. Specifically, as far as the transfection activity in the presence of serum is concerned, PEI-g-EHDO could be up to 30-fold higher than unmodified PEI25k. PEI-g-EHDO(34.5%) displayed little to no hemolytic effect and high cell-biocompatibility with nearly no cytotoxicity detected in 293T cells and HeLa cells. Taking into account the high biocompatibility and serum-tolerant transfection activity, PEI-g-EHDO(34.5%) holds great potential for the use as efficient gene vector. More importantly, it is expected that such "hydroxylation camouflage" strategy may be universally applicable for a majority of existing polycation vectors. Copyright © 2011 Elsevier Ltd. All rights reserved.

A structured understanding of cellobiohydrolase I binding to poplar lignin fractions after dilute acid pretreatment.

PubMed

Yao, Lan; Yoo, Chang Geun; Meng, Xianzhi; Li, Mi; Pu, Yunqiao; Ragauskas, Arthur J; Yang, Haitao

2018-01-01

Cellulase adsorption to lignin is considered a cost barrier for bioethanol production; however, its detailed association mechanism is still not fully understood. In this study, two natural poplar variants with high and low sugar release performance were selected as the low and high recalcitrant raw materials (named L and H , respectively). Three different lignin fractions were extracted using ethanol, followed by p -dioxane and then cellulase treatment from the dilute acid pretreated poplar solids (fraction 1, 2, and 3, respectively). Each lignin fraction had different physicochemical properties. Ethanol-extracted lignin had the lowest weight average molecular weight, while the molecular weights for the other two lignin fractions were similar. 31 P NMR analysis revealed that lignin fraction with higher molecular weight contained more aliphatic hydroxyl groups and less phenolic hydroxyl groups. Semi-quantitative analysis by 2D HSQC NMR indicated that the lignin fractions isolated from the natural variants had different contents of syringyl (S), guaiacyl (G) and interunit linkages. Lignin extracted by ethanol contained the largest amount of S units, the smallest amounts of G and p -hydroxybenzoate (PB) subunits, while the contents of these lignin subunits in the other two lignin fractions were similar. The lignin fraction obtained after cellulase treatment was primarily comprised of β- O -4 linkages with small amounts of β-5 and β-β linkages. The binding strength of these three lignin fractions obtained by Langmuir equations were in the order of L 1  >  L 3  >  L 2 for the low recalcitrance poplar and H 1  >  H 2  >  H 3 for the high recalcitrance poplar. Overall, adsorption ability of lignin was correlated with the sugar release of poplar. Structural features of lignin were associated with its binding to CBH. For natural poplar variants, lignin fractions with lower molecular weight and polydispersity index (PDI) exhibited more CBH adsorption ability. Lignins with more phenolic hydroxyl groups had higher CBH binding strength. It was also found that lignin fractions with more condensed aromatics adsorbed more CBH likely attributed to stronger hydrophobic interactions.

Carbonyl Activation by Borane Lewis Acid Complexation: Transition States of H2 Splitting at the Activated Carbonyl Carbon Atom in a Lewis Basic Solvent and the Proton-Transfer Dynamics of the Boroalkoxide Intermediate.

PubMed

Heshmat, Mojgan; Privalov, Timofei

2017-07-06

By using transition-state (TS) calculations, we examined how Lewis acid (LA) complexation activates carbonyl compounds in the context of hydrogenation of carbonyl compounds by H 2 in Lewis basic (ethereal) solvents containing borane LAs of the type (C 6 F 5 ) 3 B. According to our calculations, LA complexation does not activate a ketone sufficiently enough for the direct addition of H 2 to the O=C unsaturated bond; but, calculations indicate a possibly facile heterolytic cleavage of H 2 at the activated and thus sufficiently Lewis acidic carbonyl carbon atom with the assistance of the Lewis basic solvent (i.e., 1,4-dioxane or THF). For the solvent-assisted H 2 splitting at the carbonyl carbon atom of (C 6 F 5 ) 3 B adducts with different ketones, a number of TSs are computed and the obtained results are related to insights from experiment. By using the Born-Oppenheimer molecular dynamics with the DFT for electronic structure calculations, the evolution of the (C 6 F 5 ) 3 B-alkoxide ionic intermediate and the proton transfer to the alkoxide oxygen atom were investigated. The results indicate a plausible hydrogenation mechanism with a LA, that is, (C 6 F 5 ) 3 B, as a catalyst, namely, 1) the step of H 2 cleavage that involves a Lewis basic solvent molecule plus the carbonyl carbon atom of thermodynamically stable and experimentally identifiable (C 6 F 5 ) 3 B-ketone adducts in which (C 6 F 5 ) 3 B is the "Lewis acid promoter", 2) the transfer of the solvent-bound proton to the oxygen atom of the (C 6 F 5 ) 3 B-alkoxide intermediate giving the (C 6 F 5 ) 3 B-alcohol adduct, and 3) the S N 2-style displacement of the alcohol by a ketone or a Lewis basic solvent molecule. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Identification of potent odourants in wine and brewed coffee using gas chromatography-olfactometry and comprehensive two-dimensional gas chromatography.

PubMed

Chin, Sung-Tong; Eyres, Graham T; Marriott, Philip J

2011-10-21

Volatile constituents in wine and brewed coffee were analyzed using a combined system incorporating both GC-olfactometry (GC-O) and comprehensive two-dimensional GC-flame ionization detection (GC×GC-FID). A column set consisting of a 15m first dimension ((1)D; DB-FFAP (free fatty acid phase)), and a 1.0m (2)D column (DB-5 phase) was applied to achieve the GC×GC separation of the volatile extracts isolated by using solid phase extraction (SPE). While 1D GC resulted in many overlapping peaks, GC×GC allowed resolution of co-eluting compounds which coincided with the odour region located using GC-O. Character-impact odourants were tentatively identified through data correlation of GC×GC contour plots across results obtained using either time-of-flight mass spectrometry (TOFMS), or with flame photometric detection (FPD) for sulfur speciation. The odourants 2-methyl-2-butenal, 2-(methoxymethyl)-furan, dimethyl trisulfide, 2-ethyl-5-methyl-pyrazine, 2-octenal, 2-furancarboxaldehyde, 3-mercapto-3-methyl-1-butanol, 2-methoxy-3-(2-methylpropyl)-pyrazine, 2-furanmethanol and isovaleric acid were suspected to be particularly responsible for coffee aroma using this approach. The presented methodology was applied to identify the potent odourants in two different Australian wine varietals. 1-Octen-3-ol, butanoic acid and 2-methylbutanoic acid were detected in both Merlot and a Sauvignon Blanc+Semillon (SV) blend with high aroma potency. Several co-eluting peaks of ethyl 4-oxo-pentanoate, 3,7-dimethyl-1,5,7-octatrien-3-ol, (Z)-2-octen-1-ol, 5-hydroxy-2-methyl-1,3-dioxane were likely contributors to the Merlot wine aroma; while (Z)-3-hexen-1-ol, β-phenylethyl acetate, hexanoic acid and co-eluting peaks of 3-ethoxy-1-propanol and hexyl formate may contribute to SV wine aroma character. The volatile sulfur compound 2-mercapto-ethyl acetate was believed to contribute a fruity, brothy, meaty, sulfur odour to Australian Merlot and SV wines. Copyright © 2011 Elsevier B.V. All rights reserved.

Preparation and isolation of dithiolene thiophosphoryl molecules as stable, protected forms of dithiolene ligands.

PubMed

Arumugam, Kuppuswamy; Bollinger, James E; Fink, Mark; Donahue, James P

2007-04-16

The reaction of P4S10 with acyloins, RC(O)CH(OH)R, in refluxing dioxane, followed by the addition of alkylating agents, forms dithiolene thiophosphoryl thiolate compounds, (R2C2S2)P(S)(SR'), which are readily isolated and purified. The compounds that have been prepared and identified spectroscopically are those with R = p-anisyl, R' = Me (1); R = p-anisyl, R' = Bz (2); R = Ph, R' = Me (4); R = Et, R' = Bz (5). Compounds 1, 2, and 4 were structurally characterized by X-ray crystallography and found to possess a tetrahedral coordination geometry about the phosphorus atom, with overall Cs symmetry. In each case, the mirror plane bisects the dithiolene S-P-S chelate and contains the thiophosphoryl bond, which ranges in length from 1.9241(8) to 1.9361(7) A. The use of 2-(bromomethyl)naphthalene as organic electrophile in the P4S10/acyloin reaction produced bis(2-methylnaphthalenyl) disulfide as the only identifiable product. The substitution of Lawesson's reagent for P4S10 in reactions with acyloins produced deoxy acyloin rather than products resulting from chalcogen exchange. Compounds 1-2 and 4-5 are Group 5 analogues of 1,3-dithiol-2-ones, (R2C2S2)C=O, and undergo a similar hydrolysis in aqueous base to liberate ene-1,2-dithiolate dianions from which corresponding metal dithiolene complexes may be prepared. Deprotection of 1 in MeO-/MeOH, followed by the addition of NiCl2.6H2O and then I2, produces square planar [Ni(S2C2(C6H4-p-OCH3)2)2] (8) in 93% yield. A high-resolution structure of 8 (P) reveals dithiolene C-C and C-S bond lengths that are clearly indicative of the thionyl radical monoanionic nature of the ligand. The use of isolated (R2C2S2)P(S)(SR') compounds as a dithiolene ligand source for the preparation of metal dithiolene complexes offers the advantages of clean reactivity and high yield.

A structured understanding of cellobiohydrolase I binding to poplar lignin fractions after dilute acid pretreatment

DOE PAGES

Yao, Lan; Yoo, Chang Geun; Meng, Xianzhi; ...

2018-04-04

Background: Cellulase adsorption to lignin is considered a cost barrier for bioethanol production; however, its detailed association mechanism is still not fully understood. In this study, two natural poplar variants with high and low sugar release performance were selected as the low and high recalcitrant raw materials (named L and H, respectively). Three different lignin fractions were extracted using ethanol, followed by p-dioxane and then cellulase treatment from the dilute acid pretreated poplar solids (fraction 1, 2, and 3, respectively).Results: Each lignin fraction had different physicochemical properties. Ethanol-extracted lignin had the lowest weight average molecular weight, while the molecular weightsmore » for the other two lignin fractions were similar. 31P NMR analysis revealed that lignin fraction with higher molecular weight contained more aliphatic hydroxyl groups and less phenolic hydroxyl groups. Semi-quantitative analysis by 2D HSQC NMR indicated that the lignin fractions isolated from the natural variants had different contents of syringyl (S), guaiacyl (G) and interunit linkages. Lignin extracted by ethanol contained the largest amount of S units, the smallest amounts of G and p-hydroxybenzoate (PB) subunits, while the contents of these lignin subunits in the other two lignin fractions were similar. The lignin fraction obtained after cellulase treatment was primarily comprised of β-O-4 linkages with small amounts of β-5 and β–β linkages. The binding strength of these three lignin fractions obtained by Langmuir equations were in the order of L1 > L3 > L2 for the low recalcitrance poplar and H1 > H2 > H3 for the high recalcitrance poplar.Conclusions: Overall, adsorption ability of lignin was correlated with the sugar release of poplar. Structural features of lignin were associated with its binding to CBH. For natural poplar variants, lignin fractions with lower molecular weight and polydispersity index (PDI) exhibited more CBH adsorption ability. Lignins with more phenolic hydroxyl groups had higher CBH binding strength. It was also found that lignin fractions with more condensed aromatics adsorbed more CBH likely attributed to stronger hydrophobic interactions.« less

Tautomeric and Microscopic Protonation Equilibria of Anthranilic Acid and Its Derivatives.

PubMed

Zapała, Lidia; Woźnicka, Elżbieta; Kalembkiewicz, Jan

2014-01-01

The acid-base chemistry of three zwitterionic compounds, namely anthranilic (2-aminobenzoic acid), N -methylanthranilic and N -phenylanthranilic acid has been characterized in terms of the macroconstants K a1 , K a2 , the isoelectric point p H I , the tautomerization constant K z and microconstants k 11 , k 12 , k 21 , k 22 . The potentiometric titration method was used to determine the macrodissociation constants. Due to the very poor water solubility of N -phenylanthranilic acid the dissociation constants p K a1 and p K a2 were determined in MDM-water mixtures [MDM is a co-solvent mixture, consisting of equal volumes of methanol (MeOH), dioxane and acetonitrile (MeCN)]. The Yasuda-Shedlovsky extrapolation procedure has been used to obtain the values of p K a1 and p K a2 in aqueous solutions. The p K a1 and p K a2 values obtained by this method are 2.86 ± 0.01 and 4.69 ± 0.03, respectively. The tautomerization constant K z describing the equilibrium between unionized form ⇌ zwitterionic form was evaluated by the K z method based on UV-VIS spectrometry. The method uses spectral differences between the zwitterionic form (found at isoelectric pH in aqueous solution) and the unionized form (formed in an organic solvent of low dielectric constant). The highest value of the K z constant has been observed in the case of N -methylantranilic acid (log 10 K z  = 1.31 ± 0.04). The values of log 10 K z for anthranilic and N -phenylanthranilic acids are similar and have values of 0.93 ± 0.03 and 0.90 ± 0.05, respectively. The results indicate that the tested compounds, in aqueous solution around the isoelectric point pH I , occur mainly in the zwitterionic form. Moreover, the influence of the type of substituent and pH of the aqueous phase on the equilibrium were analyzed with regard to the formation and the coexistence of different forms of the acids in the examined systems.

Safety assessment of poloxamers 101, 105, 108, 122, 123, 124, 181, 182, 183, 184, 185, 188, 212, 215, 217, 231, 234, 235, 237, 238, 282, 284, 288, 331, 333, 334, 335, 338, 401, 402, 403, and 407, poloxamer 105 benzoate, and poloxamer 182 dibenzoate as used in cosmetics.

PubMed

Singh-Joy, Subhashni D; McLain, Valerie C

2008-01-01

Poloxamers are polyoxyethlyene, polyoxypropylene block polymers. The impurities of commercial grade Poloxamer 188, as an example, include low-molecular-weight substances (aldehydes and both formic and acetic acids), as well as 1,4-dioxane and residual ethylene oxide and propylene oxide. Most Poloxamers function in cosmetics as surfactants, emulsifying agents, cleansing agents, and/or solubilizing agents, and are used in 141 cosmetic products at concentrations from 0.005% to 20%. Poloxamers injected intravenously in animals are rapidly excreted in the urine, with some accumulation in lung, liver, brain, and kidney tissue. In humans, the plasma concentration of Poloxamer 188 (given intravenously) reached a maximum at 1 h, then reached a steady state. Poloxamers generally were ineffective in wound healing, but were effective in reducing postsurgical adhesions in several test systems. Poloxamers can cause hypercholesterolemia and hypertriglyceridemia in animals, but overall, they are relatively nontoxic to animals, with LD(50) values reported from 5 to 34.6 g/kg. Short-term intravenous doses up to 4 g/kg of Poloxamer 108 produced no change in body weights, but did result in diffuse hepatocellular vacuolization, renal tubular dilation in kidneys, and dose-dependent vacuolization of epithelial cells in the proximal convoluted tubules. A short-term inhalation toxicity study of Poloxamer 101 at 97 mg/m(3) identified slight alveolitis after 2 weeks of exposure, which subsided in the 2-week postexposure observation period. A short-term dermal toxicity study of Poloxamer 184 in rabbits at doses up to 1000 mg/kg produced slight erythema and slight intradermal inflammatory response on histological examination, but no dose-dependent body weight, hematology, blood chemistry, or organ weight changes. A 6-month feeding study in rats and dogs of Poloxamer 188 at exposures up to 5% in the diet produced no adverse effects. Likewise, Poloxamer 331 (tested up to 0.5 g/kg day(-1)), Poloxamer 235 (tested up to 1.0 g/kg day(-1)), and Poloxamer 338 (at 0.2 or 1.0 g/kg day(-1)) produced no adverse effects in dogs. Poloxamer 338 (at 5.0 g/kg day(-1)) produced slight transient diarrhea in dogs. Poloxamer 188 at levels up to 7.5% in diet given to rats in a 2-year feeding study produced diarrhea at 5% and 7.5% levels, a small decrease in growth at the 7.5% level, but no change in survival. Doses up to 0.5 mg/kg day(-1) for 2 years using rats produced yellow discoloration of the serum, high serum alkaline phosphatase activity, and elevated serum glutamicpyruvic transaminase and glutamic-oxalacetic transaminase activities. Poloxamers are minimal ocular irritants, but are not dermal irritants or sensitizers in animals. Data on reproductive and developmental toxicity of Poloxamers were not found. An Ames test did not identify any mutagenic activity of Poloxamer 407, with or without metabolic activation. Several studies have suggested anticarcinogenic effects of Poloxamers. Poloxamers appear to increase the sensitivity to anticancer drugs of multidrug-resistant cancer cells. In clinical testing, Poloxamer 188 increased the hydration of feces when used in combination with a bulk laxative treatment. Compared to controls, one study of angioplasty patients receiving Poloxamer 188 found a reduced myocardial infarct size and a reduced incidence of reinfarction, with no evidence of toxicity, but two other studies found no effect. Poloxamer 188 given to patients suffering from sickle cell disease had decreased pain and decreased hospitilization, compared to controls. Clinical tests of dermal irritation and sensitization were uniformly negative. The Cosmetic Ingredient Review (CIR) Expert Panel stressed that the cosmetic industry should continue to use the necessary purification procedures to keep the levels below established limits for ethylene oxide, propylene oxide, and 1,4-dioxane. The Panel did note the absence of reproductive and developmental toxicity data, but, based on molecular weight and solubility, there should be little skin penetration and any penetration of the skin should be slow. Also, the available data demonstrate that Poloxamers that are introduced into the body via routes other than dermal exposure have a rapid clearance from the body, suggesting that there would be no risk of reproductive and/or developmental toxicity. Overall, the available data do not suggest any concern about carcinogenesis. Although there are gaps in knowledge about product use, the overall information available on the types of products in which these ingredients are used, and at what concentration, indicates a pattern of use. Based on these safety test data and the information that the manufacturing process can be controlled to limit unwanted impurities, the Panel concluded that these Poloxamers are safe as used.

Scintillating Cocktail Mixtures and the Role of Water on the Optophysical Properties.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cordaro, Joseph Gabriel; Feng, Patrick L.; Mengesha, Wondwosen

2015-10-01

Two types of water - containing liquid scinti llation mixtures were prepared in the present work. In the first, m ixtures of 2 - phenylethanol, water, diphenyl phosphate, sodium phenyl phosphate dibasic dihydrate, and the dye 2,5 - diphenyloxazole (PPO) have been investigated as liquid scintillators. In th e second system, nonionic and mixed surfactant systems were investigated in conjunction with water and small amounts of toluene. In both cases, increasing amounts of water led to reductions in the scintillation light yield. Understanding what factors contr ibute to this phenomenon is the focus of this report. Changes in the solutionmore » microphase structure, diminishing aromatic content of the cocktail mixtures, and inefficient energy transfer to the dye a ppear to be responsible for the decreased light yield as more water is added . In the 2 - phenylethanol system, the observed experimental results are consistent with the formation of a bicontinuous microemulsion at higher water concentrations, which incorporates PPO and shields it from the quenching effects of the increasing polar matrix. Evidence for this proposed phase chan ge c ome s from light scattering data, photo - and x - ray luminescence measurements, and optical transparency measurements . In the surfactant - based system, the quenching effect of water was found to be less than both commercially - available dioxane - naphthalene mixtures used for scintillation counting as well as the 2 - phenylethanol mixtures described above. The effect of different surfactant mixtures and concentrations were studied, revealing a benefic ial effect upon the scintillation light yield for mixed surfactant mixtures. These results are interpreted in the context of r eactive radical species formation following water ionization , which leads to light - yield quenching in aqueous systems . The presenc e of surfactant(s) in these mixtures enables the formation of organic - rich regions that are spatially separated from the reactive radicals. This hypothesis is consistent with subsequent experiments that showed reduced light - yield quenching in the presence of radical - trapping additives. A notable result from these surfactant studies was the preparation of an aqueous scintillator that was transparent and showed neutron/gamma pulse - shape discrimination. Section II below provides background information on the s ignificance of this finding. The combined work described herein has implications on other efforts to make water - based solution scintillators -- without aromatic content an efficient mechanism for ionizing radiation to sensitize emission from a dye is limited.« less

Ex situ generation of stoichiometric HCN and its application in the Pd-catalysed cyanation of aryl bromides: evidence for a transmetallation step between two oxidative addition Pd-complexes.

PubMed

Kristensen, Steffan K; Eikeland, Espen Z; Taarning, Esben; Lindhardt, Anders T; Skrydstrup, Troels

2017-12-01

A protocol for the Pd-catalysed cyanation of aryl bromides using near stoichiometric and gaseous hydrogen cyanide is reported for the first time. A two-chamber reactor was adopted for the safe liberation of ex situ generated HCN in a closed environment, which proved highly efficient in the Ni-catalysed hydrocyanation as the test reaction. Subsequently, this setup was exploited for converting a range of aryl and heteroaryl bromides (28 examples) directly into the corresponding benzonitriles in high yields, without the need for cyanide salts. Cyanation was achieved employing the Pd(0) precatalyst, P( t Bu) 3 -Pd-G3 and a weak base, potassium acetate, in a dioxane-water solvent mixture. The methodology was also suitable for the synthesis of 13 C-labelled benzonitriles with ex situ generated 13 C-hydrogen cyanide. Stoichiometric studies with the metal complexes were undertaken to delineate the mechanism for this catalytic transformation. Treatment of Pd(P( t Bu) 3 ) 2 with H 13 CN in THF provided two Pd-hydride complexes, (P( t Bu) 3 ) 2 Pd(H)( 13 CN), and [(P( t Bu) 3 )Pd(H)] 2 Pd( 13 CN) 4 , both of which were isolated and characterised by NMR spectroscopy and X-ray crystal structure analysis. When the same reaction was performed in a THF : water mixture in the presence of KOAc, only (P( t Bu) 3 ) 2 Pd(H)( 13 CN) was formed. Subjection of this cyano hydride metal complex with the oxidative addition complex (P( t Bu) 3 )Pd(Ph)(Br) in a 1 : 1 ratio in THF led to a transmetallation step with the formation of (P( t Bu) 3 ) 2 Pd(H)(Br) and 13 C-benzonitrile from a reductive elimination step. These experiments suggest the possibility of a catalytic cycle involving initially the formation of two Pd(ii)-species from the oxidative addition of L n Pd(0) into HCN and an aryl bromide followed by a transmetallation step to L n Pd(Ar)(CN) and L n Pd(H)(Br), which both reductively eliminate, the latter in the presence of KOAc, to generate the benzonitrile and L n Pd(0).

Final report on the safety assessment of octoxynol-1, octoxynol-3, octoxynol-5, octoxynol-6, octoxynol-7, octoxynol-8, octoxynol-9, octoxynol-10, octoxynol-11, octoxynol-12, octoxynol-13, octoxynol-16, octoxynol-20, octoxynol-25, octoxynol-30, octoxynol-33, octoxynol-40, octoxynol-70, octoxynol-9 carboxylic acid, octoxynol-20 carboxylic acid, potassium octoxynol-12 phosphate, sodium octoxynol-2 ethane sulfonate, sodium octoxynol-2 sulfate, sodium octoxynol-6 sulfate, and sodium octoxynol-9 sulfate.

PubMed

Johnson, Wilbur

2004-01-01

Octoxynols are ethoxylated alkylphenols in which the size of the molecule is related to the number of moles of ethylene oxide used in synthesis. Reactions are performed at elevated temperature, under pressure, and in the presence of NaOH. It is possible that the synthesis may leave trace amounts of ethylene oxide, 1,4-dioxane, and unreacted C9 phenols. Octoxynols of various chain lengths as well as octoxynol salts and organic acids function in cosmetics either as surfactants--emulsifying agents, surfactants--cleansing agents, surfactant--solubilizing agents, or surfactants--hydrotropes in a wide variety of cosmetic products at concentrations ranging from 0.0008% to 25%, with most less than 5.0%. The octoxynols are chemically similar to nonoxynols, the safety of which were previously considered. Long-chain nonoxynols (9 and above) were considered safe as used, whereas short-chain nonoxynols (8 and below) were considered safe as used in rinse-off products and safe at concentrations less than 5% in leave-on formulations. Acute exposure of hamsters to Octoxynol-9 by bronchopulmonary lavage produced pneumonia, pulmonary edema, and intra-alveolar hemorrhage. Octoxynol-9 at doses over 1 g/kg was toxic in rats and in mice in acute oral toxicity studies. No significant effects were noted in short-term oral studies of Octoxynol-9 in rats, in subchronic oral studies of Octoxynol-40 in rats and dogs, or in chronic oral studies of Octoxynol-40 in rats. The intraperitoneal LD50 of Octoxynol-9 in rats and mice was around 100 mg/kg. In skin irritation studies, octoxynols ranged from nonirritating to moderately irritating. Octoxynols were not ocular irritants in one rabbit study, but in others there was ocular irritation. No immune system toxicity in CF-1 female mice was noted following the intraperitoneal injection of Octoxynol-9 followed by subcutaneous immunization with sheep red blood cells (SRBCs). Octoxynol-9 produced no humoral and cell-mediated immune responses, or autoimmune response in mice. In the Ames test, Octoxynol-1 was not mutagenic with and without metabolic activation nor was Octoxynol-9 clastogenic. Results for Octoxynol-9 were negative in the following assays: unscheduled DNA synthesis, hypoxanthine guanine phosphoribosyl transferase mutation assay, malignant transformation assay, DNA alkaline unwinding test, and mouse lymphoma thymidine kinase locus forward mutation assay. Ethoxylated alkylphenols are generally considered to be estrogenic in that they mimic the effects of estradiol. Dermal exposure at three dose levels of rats to Octoxynol-9 failed to induce any malformations by category (external, visceral, or skeletal) or by individual anatomical location that were different from controls at statistically significant level. An increased incidence of a vestigial thoracic rib was observed in all dose groups. Octoxynol-9 also did not induce developmental toxicity (number of viable litters, liveborn per litter, percentage survival, birth weight per pup, and weight gain per pup) in female specific pathogen-free CD-1 mice dosed daily by gavage on gestation days 6 through 13. No reproductive toxicity was seen in male albino rats which received 5% Octoxynol-40 in the diet daily for 3 months; however, in an in vitro test, Octoxynol-9 (0.24 mg/ml) totally immobilized all human spermatozoa within 20 s. Women who used Nonoxynol-9 or Octoxynol-9 as spermicides, but who did become pregnant, did not have an increase in the overall risk of fetal malformations. In a human skin irritation study, formulations containing 2.0% Octoxynol-9 were classified as moderately irritating and minimally irritating, respectively, in a 24-h single-insult, occlusive patch test. Octoxynol-9 (1.0%) was classified as a nonirritant in a clinical study of nine subjects patch tested for 4 consecutive days. The skin sensitization potential of Octoxynols-1, -3, -5, -9, and -13 was evaluated using 50 subjects. Octoxynol-1 induced sensitization in two subjects; all other results were negative. No sensitization was observed in the following studies: 8.0% Octoxynol-9 in 103 subjects, 0.5% Octoxynol-9 in 102 subjects, and 0.1% Octoxynol-9 in 206 subjects. Concerns about even trace levels of 1,4-dioxane, ethylene oxide, or unreacted C9 led to the recommendation that levels be limited. Concerns about the ocular irritancy of short-chain octoxynols led to a recommendation that they should not be used in products that will be used in the area surrounding the eyes. A limitation on the use concentration for short-chain octoxynols (8 and below) arose from consideration of the skin sensitization potential of octoxynols and the recognition that the short-chain octoxynols could be absorbed into the skin more than the long-chain octoxynols. Overall, based on the available data, it was concluded that long-chain octoxynols (9 and above) are safe as used, whereas short-chain octoxynols (8 and below) are safe as used in rinse-off products and safe at concentrations less than 5% in leave-on formulations.

A survey of household products for volatile organic compounds

NASA Astrophysics Data System (ADS)

Sack, Thomas M.; Steele, David H.; Hammerstrom, Karen; Remmers, Janet

A total of 1159 common household products were analysed for 31 volatile organic compounds as potential sources of indoor air pollution. The products were distributed among 65 product categories within 8 category classes: automotive products (14.4% of the products); household cleaners/polishes (9.6%); paint-related products (39.9%); fabric and leather treatments (7.9%); cleaners for electronic equipment (6.0%); oils, greases and lubricants (9.6%); adhesive-related products (6.6%); and miscellaneous products (6.1%). The study was conducted in two parts. In the first part, or the original study, the products were reanalysed for methylene chloride and five other chlorocarbons using purge-and-trap gas chromatography/mass spectrometry (GC/MS), and a data base containing the analytical results was developed. Because full mass spectra were taken, the original set of GC/MS data also contained information regarding other volatile chemicals in the products. However, this additional data was not reported at that time. In the second part of the study, the GC/MS data were reanalysed to determine the presence and concentrations of an additional 25 volatile chemicals. The 31 chemicals included in both parts of this study were: carbon tetrachloride; methylene chloride; tetrachloroethylene; 1,1,1-trichloroethane; trichlorethylene; 1,1,2-tricholorotrifluoroethane; acetone; benzene; 2-butanone; chlorobenzene; chloroform; cyclohexane; 1,2-dichloroethane; 1,4-dioxane; ethylbenzene; n-hexane; d-limonene; methylcyclohexane; methylcyclopentane; methyl isobutyl ketone; n-nonane; n-octane; α-pinene; propylene oxide; styrene; 1,1,2,2-tetrachloroethane; tetrahydrofuran; toluene; m-mxylene; o-xylene; and p-xylene. Of the 31 chemicals, toluene, the xylenes and methylene chloride were found to occur most frequently—in over 40% of the products tested. Chemicals that were typically found in relatively high concentrations in the samples (i.e. greater than 20% w/w) included acetone, 2-butanone, hexane, methylene chloride, tetrachloroethylene, toluene, 1,1,1-trichloroethane, trichloroethylene, 1,1,2-trichlorotrifluoroethane and the xylenes. Chlorobenzene, d-limonene, 1,1,2,2-tetrachloroethane, n-nonane and styrene were not found in any of the products at or above the 0.1% level. In all, 935 of the products contained one or more of the target solvents at levels greater than 0.1%. The resulting data base contains information regarding the 1159 products, such as origin, cost, container type, lot number, etc., as well as quantitative information for each of the 31 chemicals. The frequency of occurrence and average concentrations for the target chemicals are summarized for each of the product classes.

Toxicological risk assessment and prioritization of drinking water relevant contaminants of emerging concern.

PubMed

Baken, Kirsten A; Sjerps, Rosa M A; Schriks, Merijn; van Wezel, Annemarie P

2018-06-13

Toxicological risk assessment of contaminants of emerging concern (CEC) in (sources of) drinking water is required to identify potential health risks and prioritize chemicals for abatement or monitoring. In such assessments, concentrations of chemicals in drinking water or sources are compared to either (i) health-based (statutory) drinking water guideline values, (ii) provisional guideline values based on recent toxicity data in absence of drinking water guidelines, or (iii) generic drinking water target values in absence of toxicity data. Here, we performed a toxicological risk assessment for 163 CEC that were selected as relevant for drinking water. This relevance was based on their presence in drinking water and/or groundwater and surface water sources in downstream parts of the Rhine and Meuse, in combination with concentration levels and physicochemical properties. Statutory and provisional drinking water guideline values could be derived from publically available toxicological information for 142 of the CEC. Based on measured concentrations it was concluded that the majority of substances do not occur in concentrations which individually pose an appreciable human health risk. A health concern could however not be excluded for vinylchloride, trichloroethene, bromodichloromethane, aniline, phenol, 2-chlorobenzenamine, mevinphos, 1,4-dioxane, and nitrolotriacetic acid. For part of the selected substances, toxicological risk assessment for drinking water could not be performed since either toxicity data (hazard) or drinking water concentrations (exposure) were lacking. In absence of toxicity data, the Threshold of Toxicological Concern (TTC) approach can be applied for screening level risk assessment. The toxicological information on the selected substances was used to evaluate whether drinking water target values based on existing TTC levels are sufficiently protective for drinking water relevant CEC. Generic drinking water target levels of 37 μg/L for Cramer class I substances and 4 μg/L for Cramer class III substances in drinking water were derived based on these CEC. These levels are in line with previously reported generic drinking water target levels based on original TTC values and are shown to be protective for health effects of the majority of contaminants of emerging concern evaluated in the present study. Since the human health impact of many chemicals appearing in the water cycle has been studied insufficiently, generic drinking water target levels are useful for early warning and prioritization of CEC with unknown toxicity in drinking water and its sources for future monitoring. Copyright © 2018 Elsevier Ltd. All rights reserved.

Homo- and Heterometallic Bis(Pentafluorobenzoyl)Methanide Complexes of Copper(II) and Cobalt(II)

NASA Astrophysics Data System (ADS)

Crowder, Janell M.

beta-Diketones are well known to form metal complexes with practically every known metal and metalloid. Metal complexes of fluorinated beta-diketones generally exhibit increased volatility and thermal stability compared to the non-fluorinated analogues, and thus are used extensively in various chemical vapor deposition (CVD) processes for the deposition of metal, simple or mixed metal oxides, and fluorine-doped metal oxide thin films. Furthermore, the electron-withdrawing nature of the fluorinated ligand enhances the Lewis acidity of a coordinatively unsaturated metal center which facilitates additional coordination reactions. The physical and structural properties of fluorinated beta-diketonate complexes are discussed in Chapter 1 and a few key application examples are given. The focus of this work is the synthesis and single crystal X-ray structural characterization of unsolvated and coordinatively unsaturated metal complexes of bis(pentafluorobenzoyl)- methanide (L, C6F5COCHCOC 6F5-). In Chapter 2, we present the preparation and isolation of the unsolvated complex [Cu(L)2] in pure crystalline form for the first time. We subsequently investigated the reaction of unsolvated [Cu(L)2] with sodium hexafluoroacetylacetonate [Na(hfac)] in a solvent-free environment. This reaction allowed the isolation of the first heterometallic Na-Cu diketonate [Na2Cu2(L) 4(hfac)2] structurally characterized by single crystal X-ray crystallography. Thermal decomposition of [Na2Cu2(L) 4(hfac)2] was investigated for its potential application in MOCVD processes. In the final chapter, we present the first exploration of the anhydrous synthesis of Co(II) complexed with bis(pentafluorobenzoyl)methanide in order to produce a complex without ligated water. Single crystal X-ray crystallographic investigations revealed the isolation of the ethanol adduct, [Co2(L)4(C2H5OH)2], and following the removal of ethanol, a 1,4-dioxane adduct, [{Co 2(L)4}2(C4H8O2)]. In this work, we have provided the first investigation of the synthesis, isolation and single crystal X-ray structural characterization of unsolvated and coordinatively unsaturated Cu(II) and Co(II) complexes of bis(pentafluorobenzoyl)methanide ligand. These studies demonstrate how the electrophilicity of a coordinatively unsaturated metal complexed to highly-fluorinated â-diketone ligands can be utilized for the formation of new adducts or new and interesting heterometallic complexes. This body of work provides a basis upon which future research into unsolvated and unligated bis(pentafluorobenzoyl)methanide metal complexes can expand.

Synthesis, properties and applications of bio-based materials

NASA Astrophysics Data System (ADS)

Srinivasan, Madhusudhan

Bio-based feedstock have become very significant as they offer a value proposition in terms of carbon balance and also in terms of endowing biodegradability where needed. Thus a lot of attention is being given to the modification such feedstock for different applications. Soybean oil is one such feedstock. The oil is a triglyceride ester composed of different fatty acids, which are common to other plant oils. Thus soybean oil serves as a platform for plant oils, as modifications of this oil, can in theory be extended to cover other plant oils. Methyl oleate was used as a model fatty acid ester, to synthesize hydroxyesters with ethylene glycol via a two stage oxidative cleavage of the double bonds. Ozone was chosen as the oxidant due to its many advantages. The first stage involved oxidation of the double bond to aldehydes, ozonides and acetals, which were subsequently converted to hydroxyesters (hydroxy values of 220 - 270) in near quantitative yield by treatment with Oxone. This method could be extended to soybean oil to make "polyols" which could find applications in resin syntheses. Silylation was employed as another platform to functionalize soybean oil and fatty acid methyl esters with a reactive silane (vinyltrimethoxy silane). This simple modification produced materials that are cured by atmospheric moisture and are useful as coatings. The silylation was controlled by varying the grafting time, cure temperature and the concentration of the silane. Products with gel content as high as 90% could be achieved. The coating exhibited good adhesion to metal, glass, concrete and paper. Steel panels coated with these coatings exhibited good stability against corrosion in high humidity conditions and moderate stability against a salt spray. The silylation was also successfully utilized to improve the tensile strength of the blend of biodegradable polyester, poly (butylene adipate-co-terephthalate) with talc. A reactive extrusion process was employed to graft vinyl silanes on the polyester in short reaction times of 5 minutes. This improved the compatibility with the talc filler. This biodegradable polyester product was characterized by high tensile strength and moderate elongation. The modification method is simple is applicable to a variety of aliphatic biodegradable polyesters. Finally a rapid polymerization of 1, 4-dioxan-2-one in very short times was accomplished with titanium alkoxides as initiators. At low [monomer]/ [initiator] ratios (100:1), nearly all the alkoxide groups initiated polymerization. High conversions up to 90% were achieved even at high ratios (2400:1). The activation energy for polymerization for titanium tetraisopropoxide is the lowest reported (33.5 kJ/mol) for this monomer system.

Enhanced Ga2O3-photocatalyzed and photochemical degradation of the Fipronil insecticide by UVC irradiation in mixed aqueous/organic media under an inert atmosphere.

PubMed

Hidaka, Hisao; Tsukamoto, Tohru; Mitsutsuka, Yoshihiro; Oyama, Toshiyuki; Serpone, Nick

2015-05-01

Agrochemicals such as the insecticide Fipronil that bear fluoro groups are generally fat-soluble and nearly insoluble in water, so that their photodegradation in a heterogeneous aqueous gallium oxide dispersion presents some challenges. This article examined the photodegradation of this insecticide by solubilizing it through the addition of organic solvents (EtOH, MeOH, THF, 1,4-dioxane and ethylene glycol) to an aqueous medium and then subjecting the insecticide to 254 nm UVC radiation under photocatalytically inert (Ga2O3/N2) and air-equilibrated (Ga2O3/O2) conditions, as well as photochemically in the absence of Ga2O3 but also under inert and air-equilibrated conditions. Defluorination, dechlorination, desulfonation and denitridation of Fipronil were examined in mixed aqueous/organic media (10, 25 and 50 vol% in organic solvent). After 3 h of UVC irradiation (50 vol% mixed media) defluorination with Ga2O3/N2 was ∼65% greater than in aqueous media, and ca. 80% greater than the direct photolysis of Fipronil under inert (N2) conditions; under air-equilibrated conditions both Ga2O3-photocatalyzed and photochemical defluorination were significantly lower than in aqueous media. Dechlorination of Fipronil was ∼160% (Ga2O3/N2) and 140% (photochemically, N2) greater than in aqueous media; under air-equilibrated conditions, both photocatalyzed and photochemical formation of Cl(-) ions in mixed media fell rather short relative to aqueous media. The photocatalyzed (Ga2O3/N2) and photochemical (N2) conversion of the sulfur group in Fipronil to SO4(2(-)) ions was ca. 20% and 30% greater, respectively, in mixed media, while under air-equilibrated conditions photocatalyzed desulfonation was nearly twofold less than in the aqueous phase; direct photolysis showed little variations in mixed media. Denitridation of the nitrogens in Fipronil occurred mostly through the formation of ammonia (as NH4(+)) under all conditions with negligible quantities of NO3(-); again mixed media offered enhanced denitridation, particularly under inert N2 conditions. Time-of-flight electrospray (TOF-MS/ESI(-)) mass spectrometry revealed a fairly large number of intermediates formed in the degradation of Fipronil, particularly under photocatalytic conditions. Only a couple of intermediates were identified in the photodegradation and the presence of Ga2O3 enhanced the complexity of an already cumbersome problem owing to the involvement of organic solvents.

One barbiturate and two solvated thiobarbiturates containing the triply hydrogen-bonded ADA/DAD synthon, plus one ansolvate and three solvates of their coformer 2,4-diaminopyrimidine.

PubMed

Hützler, Wilhelm Maximilian; Egert, Ernst; Bolte, Michael

2016-09-01

A path to new synthons for application in crystal engineering is the replacement of a strong hydrogen-bond acceptor, like a C=O group, with a weaker acceptor, like a C=S group, in doubly or triply hydrogen-bonded synthons. For instance, if the C=O group at the 2-position of barbituric acid is changed into a C=S group, 2-thiobarbituric acid is obtained. Each of the compounds comprises two ADA hydrogen-bonding sites (D = donor and A = acceptor). We report the results of cocrystallization experiments of barbituric acid and 2-thiobarbituric acid, respectively, with 2,4-diaminopyrimidine, which contains a complementary DAD hydrogen-bonding site and is therefore capable of forming an ADA/DAD synthon with barbituric acid and 2-thiobarbituric acid. In addition, pure 2,4-diaminopyrimidine was crystallized in order to study its preferred hydrogen-bonding motifs. The experiments yielded one ansolvate of 2,4-diaminopyrimidine (pyrimidine-2,4-diamine, DAPY), C4H6N4, (I), three solvates of DAPY, namely 2,4-diaminopyrimidine-1,4-dioxane (2/1), 2C4H6N4·C4H8O2, (II), 2,4-diaminopyrimidine-N,N-dimethylacetamide (1/1), C4H6N4·C4H9NO, (III), and 2,4-diaminopyrimidine-1-methylpyrrolidin-2-one (1/1), C4H6N4·C5H9NO, (IV), one salt of barbituric acid, viz. 2,4-diaminopyrimidinium barbiturate (barbiturate is 2,4,6-trioxopyrimidin-5-ide), C4H7N4(+)·C4H3N2O3(-), (V), and two solvated salts of 2-thiobarbituric acid, viz. 2,4-diaminopyrimidinium 2-thiobarbiturate-N,N-dimethylformamide (1/2) (2-thiobarbiturate is 4,6-dioxo-2-sulfanylidenepyrimidin-5-ide), C4H7N4(+)·C4H3N2O2S(-)·2C3H7NO, (VI), and 2,4-diaminopyrimidinium 2-thiobarbiturate-N,N-dimethylacetamide (1/2), C4H7N4(+)·C4H3N2O2S(-)·2C4H9NO, (VII). The ADA/DAD synthon was succesfully formed in the salt of barbituric acid, i.e. (V), as well as in the salts of 2-thiobarbituric acid, i.e. (VI) and (VII). In the crystal structures of 2,4-diaminopyrimidine, i.e. (I)-(IV), R2(2)(8) N-H...N hydrogen-bond motifs are preferred and, in two structures, additional R3(2)(8) patterns were observed.

Nonlinear Optical Properties of High-Temperature Organic Structures

NASA Astrophysics Data System (ADS)

Shi, Rui-Fang

In this thesis, we report the discovery of a new class of electro-optic organic structures, 1,8-naphthoylene -benzimidazoles, developed with computer aided molecular design combined with actual syntheses. These structures are similar to polyimide repeat units and possess high thermal, chemical and photo stabilities. Thermal analysis shows that the new class retains its linear and nonlinear optical properties well above 300^circ C in both pure forms and guest/host polyimide systems. Importantly, side group substitutions not only increase the second-order optical responses but also enhance the thermal stability. The origin of the relatively large second order optical responses of the new class is revealed by quantum many-electron calculations that explicitly take electron -electron correlations into consideration. Contour diagrams indicate that electrons are decreased on the benzimidazole -donor-substituted side and increased on the naphthoylene side upon virtual excitations, illustrating the fact that the naphthoylene group acts both as an electron acceptor and a pi-bridge that provides the necessary electron delocalization. Results for most structures show that the most dominant virtual excitation process to beta_{ijk}(-omega _3;omega_1,omega_2) involves the ground (S_0) and first excited (S_1) pi -electronic states. Importantly, increasing the electron donor strength increase the electric dipole moments and transition moments, therefore second order optical responses are enhanced. Interestingly, it is found that the position of a donor group in the new class has a significant effect on second order optical responses. DC-induced second harmonic generation (DCSHG) dispersion measurements characterize the nonlinear optical properties of the new class, using both nanosecond and picosecond tunable laser sources ranging from 1400 to 2148 nm in wavelength. Comparison between theory and experiment demonstrates that there is good agreement between them over a wide nonresonant photon energy region, illustrating the great success of our understanding of the nonlinear optical responses even in these relatively complicated organic structures. In addition, it is found that these chromophores have large beta_{ijk }: for SY177 in solution with 1,4-dioxane, mu_{x}beta_ {x}(-2omega;omega,omega) + < gamma(-2omega;omega,omega,0) > 5kT = 418 times 10 ^{-48} esu and beta _{x}(-2omega;omega,omega ) 92 times 10^ {-30} esu at hbaromega = 0.65 eV. For SY215 in solution with CH _2Cl_2, mu_ {x}beta_{x}(-2omega; omega,omega) + < gamma( -2omega;omega,omega,0) > 5kT = 1468 times 10^{-48} esu and beta_{x}(-2omega; omega,omega) = 268 times 10^{-30} esu at hbaromega = 0.65 eV. The discovery and characterization of the new high temperature class represents a critical step in the development of new materials that are suitable for practical device applications. Work is underway to optimize these structures and incorporate them into waveguide devices.

Chemical Modification and Structure-property Relationships of Acrylic and Ionomeric Thermoplastic Elastomer Gels

NASA Astrophysics Data System (ADS)

Vargantwar, Pruthesh Hariharrao

Block copolymers (BCs) have remained at the forefront of materials research due to their versatility in applications ranging from hot-melt/pressure-sensitive adhesives and impact modifiers to compatibilizing agents and vibration-dampening/nanotemplating media. Of particular interest are macromolecules composed of two or more chemically dissimilar blocks covalently linked together to form triblock or pentablock copolymers. If the blocks are sufficiently incompatible and the copolymer behaves as a thermoplastic elastomer, the molecules can spontaneously self-assemble to form nanostructured materials that exhibit shape memory due to the formation of a supramolecular network. The BCs of these types are termed as conventional. When BCs contain blocks having ionic moieties such as sulfonic acid groups, they are termed as block ionomers. Designing new systems based on either conventional or ionic BCs, characterizing their structure-property relationships and later using them as electroacive polymers form the essential objectives of this work. Electroactive polymers (EAPs) exhibit electromechanical actuation when stimulated by an external electric field. In the first part of this work, it is shown that BCs resolve some of the outstanding problems presently encountered in the design of two different classes of EAP actuators: dielectric elastomers (DEs) and ionic polymer metal composites (IPMCs). All-acrylic triblock copolymer gels used as DEs actuate with high efficacy without any requirement of mechanical prestrain and, thus, eliminate the need for bulky and heavy hardware essential with prestrained dielectric actuators, as well as material problems associated with stress relaxation. The dependence of actuation behavior on gel morphology as evaluated from mechanical and microstructure studies is observed. In the case of IPMCs, ionic BCs employed in this study greatly facilitate processing compared to other contenders such as NafionRTM, which is commonly used in this class of EAPs. The unique copolymer investigated here (i) retains its mechanical integrity when highly solvated by polar solvents, (ii) demonstrates a high degree of actuation when tested in a cantilever configuration, and (iii) avoids the shortcomings of back-relaxation/overshoot within the testing conditions when used in combination with an appropriate solvent. In the second part of this work, two chemical strategies to design midblock sulfonated block ionomers are explored. In one case, selective sulfonation of the midblocks in triblock copolymers is achieved via a dioxane:sulfur trioxide chemistry, while in the other acetyl sulfate is used for the same purpose. Excellent control on the degree of sulfonation (DOS) is achieved. The block ionomers swell in different solvents while retaining their mechanical integrity. They show disorder-order, order-order, and order-reduced order morphological transitions as DOS varies. These transitions in morphologies are reflected in their thermal behavior as well. The microstructures show periodicity, which is, again, a function of DOS. The transitions are explained in terms of the molar volume expansion and volume densification of the blocks on sulfonation. The ionic levels, morphology and periodicity in microstructure are important for applications such as actuators, sensors and fuel cell membranes. The ability to tune these aspects in the ionomers designed in this work make them potential candidates for these applications.

Groundwater-Quality Data in the Colorado River Study Unit, 2007: Results from the California GAMA Program

USGS Publications Warehouse

Goldrath, Dara A.; Wright, Michael T.; Belitz, Kenneth

2010-01-01

Groundwater quality in the 188-square-mile Colorado River Study unit (COLOR) was investigated October through December 2007 as part of the Priority Basin Project of the California State Water Resources Control Board (SWRCB) Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basin Project was developed in response to the Groundwater Quality Monitoring Act of 2001, and the U.S. Geological Survey (USGS) is the technical project lead. The Colorado River study was designed to provide a spatially unbiased assessment of the quality of raw groundwater used for public water supplies within COLOR, and to facilitate statistically consistent comparisons of groundwater quality throughout California. Samples were collected from 28 wells in three study areas in San Bernardino, Riverside, and Imperial Counties. Twenty wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the Study unit; these wells are termed 'grid wells'. Eight additional wells were selected to evaluate specific water-quality issues in the study area; these wells are termed `understanding wells.' The groundwater samples were analyzed for organic constituents (volatile organic compounds [VOC], gasoline oxygenates and degradates, pesticides and pesticide degradates, pharmaceutical compounds), constituents of special interest (perchlorate, 1,4-dioxane, and 1,2,3-trichlorpropane [1,2,3-TCP]), naturally occurring inorganic constituents (nutrients, major and minor ions, and trace elements), and radioactive constituents. Concentrations of naturally occurring isotopes (tritium, carbon-14, and stable isotopes of hydrogen and oxygen in water), and dissolved noble gases also were measured to help identify the sources and ages of the sampled groundwater. In total, approximately 220 constituents and water-quality indicators were investigated. Quality-control samples (blanks, replicates, and matrix spikes) were collected at approximately 30 percent of the wells, and the results were used to evaluate the quality of the data obtained from the groundwater samples. Field blanks rarely contained detectable concentrations of any constituent, suggesting that contamination was not a significant source of bias in the data. Differences between replicate samples were within acceptable ranges and matrix-spike recoveries were within acceptable ranges for most compounds. This study did not attempt to evaluate the quality of water delivered to consumers; after withdrawal from the ground, raw groundwater typically is treated, disinfected, or blended with other waters to maintain acceptable water quality. Regulatory thresholds apply to water that is served to the consumer, not to raw groundwater. However, to provide some context for the results, concentrations of constituents measured in the raw groundwater were compared to regulatory and nonregulatory health-based thresholds established by the U.S. Environmental Protection Agency (USEPA) and the California Department of Public Health (CDPH) and to thresholds established for aesthetic concerns by CDPH. Comparisons between data collected for this study and drinking-water thresholds are for illustrative purposes only and do not indicate compliance or noncompliance with those thresholds. The concentrations of most constituents detected in groundwater samples were below drinking-water thresholds. Volatile organic compounds (VOC) were detected in approximately 35 percent of grid well samples; all concentrations were below health-based thresholds. Pesticides and pesticide degradates were detected in about 20 percent of all samples; detections were below health-based thresholds. No concentrations of constituents of special interest or nutrients were detected above health-based thresholds. Most of the major and minor ion constituents sampled do not have health-based thresholds; the exception is chloride. Concentrations of chloride, sulfate, and total dis

Ground-Water Quality Data in the Upper Santa Ana Watershed Study Unit, November 2006-March 2007: Results from the California GAMA Program

USGS Publications Warehouse

Kent, Robert; Belitz, Kenneth

2009-01-01

Ground-water quality in the approximately 1,000-square-mile Upper Santa Ana Watershed study unit (USAW) was investigated from November 2006 through March 2007 as part of the Priority Basin Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basin project was developed in response to the Groundwater Quality Monitoring Act of 2001, and is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB). The Upper Santa Ana Watershed study was designed to provide a spatially unbiased assessment of raw ground-water quality within USAW, as well as a statistically consistent basis for comparing water quality throughout California. Samples were collected from 99 wells in Riverside and San Bernardino Counties. Ninety of the wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the study unit (grid wells). Nine wells were selected to provide additional understanding of specific water-quality issues identified within the basin (understanding wells). The ground-water samples were analyzed for a large number of organic constituents (volatile organic compounds [VOCs], pesticides and pesticide degradates, pharmaceutical compounds, and potential wastewater-indicator compounds), constituents of special interest (perchlorate, N-nitrosodimethylamine [NDMA], 1,4-dioxane, and 1,2,3-trichloropropane [1,2,3-TCP]), naturally occurring inorganic constituents (nutrients, major and minor ions, and trace elements), radioactive constituents, and microbial indicators. Naturally occurring isotopes (tritium, carbon-14, and stable isotopes of hydrogen and oxygen in water) and dissolved noble gases also were measured to help identify sources and ages of the sampled ground water. Dissolved gases, and isotopes of nitrogen gas and of dissolved nitrate also were measured in order to investigate the sources and occurrence of nitrate in the study unit. In total, nearly 400 constituents and water-quality indicators were investigated for this study. This study did not attempt to evaluate the quality of water delivered to consumers; after withdrawal from the ground, water typically is treated, disinfected, and (or) blended with other waters to maintain acceptable water quality. Regulatory thresholds apply to treated water that is served to the consumer, not to raw ground water. However, to provide some context for the results, concentrations of constituents measured in the raw ground water were compared with regulatory and non-regulatory health-based thresholds established by the U.S. Environmental Protection Agency (USEPA) and the California Department of Public Health (CDPH) and thresholds established for aesthetic concerns (secondary maximum contaminant levels, SMCL-CA) by CDPH. Volatile organic compounds (VOCs) were detected in more than 80 percent of USAW grid wells. Most VOCs detected were at concentrations far less than thresholds established for drinking water to protect human health; however, six wells had VOC concentrations above health-based thresholds. Twenty-four of the 85 VOCs investigated were detected in the study unit;11 were detected in more than 10 percent of the wells. The VOCs detected above health-based thresholds in at least one well were dibromochloropropane (DBCP), tetrachloroethene (PCE), trichloroethene (TCE), carbon tetrachloride, and 1,1-dichoroethene. Pesticide compounds were detected in more than 75 percent of the grid wells. However, of the 134 different pesticide compounds investigated, 13 were detected at concentrations greater than their respective long-term method detection limits, and only 7 compounds (all herbicides or herbicide degradates) were detected in more than 10 percent of the wells. No pesticide compound was detected above its health-based threshold, although thresholds exist for fewer than half of the pesticide compounds investigat

Ground-Water Quality Data in the Coastal Los Angeles Basin Study Unit, 2006: Results from the California GAMA Program

USGS Publications Warehouse

Mathany, Timothy M.; Land, Michael; Belitz, Kenneth

2008-01-01

Ground-water quality in the approximately 860 square-mile Coastal Los Angeles Basin study unit (CLAB) was investigated from June to November of 2006 as part of the Statewide Basin Assessment Project of the Ground-Water Ambient Monitoring and Assessment (GAMA) Program. The GAMA Statewide Basin Assessment was developed in response to the Ground-Water Quality Monitoring Act of 2001, and is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB). The Coastal Los Angeles Basin study was designed to provide a spatially unbiased assessment of raw ground-water quality within CLAB, as well as a statistically consistent basis for comparing water quality throughout California. Samples were collected from 69 wells in Los Angeles and Orange Counties. Fifty-five of the wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the study area (?grid wells?). Fourteen additional wells were selected to evaluate changes in ground-water chemistry or to gain a greater understanding of the ground-water quality within a specific portion of the Coastal Los Angeles Basin study unit ('understanding wells'). Ground-water samples were analyzed for: a large number of synthetic organic constituents [volatile organic compounds (VOCs), gasoline oxygenates and their degradates, pesticides, polar pesticides, and pesticide degradates, pharmaceutical compounds, and potential wastewater-indicators]; constituents of special interest [perchlorate, N-nitrosodimethylamine (NDMA), 1,4-dioxane, and 1,2,3-trichloropropane (1,2,3-TCP)]; inorganic constituents that can occur naturally [nutrients, major and minor ions, and trace elements]; radioactive constituents [gross-alpha and gross-beta radiation, radium isotopes, and radon-222]; and microbial indicators. Naturally occurring isotopes [stable isotopic ratios of hydrogen and oxygen, and activities of tritium and carbon-14] and dissolved noble gases also were measured to help identify the sources and ages of the sampled ground water. Quality-control samples (blanks, replicates, and samples for matrix spikes) were collected at approximately one-fourth of the wells, and the results for these samples were used to evaluate the quality of the data for the ground-water samples. Field blanks rarely contained detectable concentrations of any constituent, suggesting that contamination was not a significant source of bias. Differences between replicate samples were within acceptable ranges, indicating acceptably low variability. Matrix spike recoveries were within acceptable ranges for most compounds. Assessment of the quality-control information resulted in applying ?V? codes to approximately 0.1 percent of the data collected for ground-water samples (meaning a constituent was detected in blanks as well as the corresponding environmental data). This study did not attempt to evaluate the quality of drinking water delivered to consumers; after withdrawal from the ground, water typically is treated, disinfected, and (or) blended with other waters to maintain acceptable drinking-water quality. Regulatory thresholds are applied to the treated drinking water that is served to the consumer, not to raw ground water. However, to provide some context for the results, concentrations of constituents measured in the raw ground water were compared with regulatory and non-regulatory health-based thresholds established by the U.S. Environmental Protection Agency (USEPA), California Department of Public Health (CDPH, formerly California Department of Health Services [CADHS]) and thresholds established for aesthetic concerns (secondary maximum contaminant levels, SMCL-CA) by CDPH. Comparisons between data collected for this study and drinking-water thresholds are for illustrative purposes only, and are not indicative of compliance or non-compliance with those thresholds. VOCs were detected in alm

Ground-Water Quality Data in the San Fernando-San Gabriel Study Unit, 2005 - Results from the California GAMA Program

USGS Publications Warehouse

Land, Michael; Belitz, Kenneth

2008-01-01

Ground-water quality in the approximately 460 square mile San Fernando-San Gabriel study unit (SFSG) was investigated between May and July 2005 as part of the Priority Basin Assessment Project of the Groundwater Ambient Monitoring and Assessment (GAMA) Program. The GAMA Priority Basin Assessment Project was developed in response to the Groundwater Quality Monitoring Act of 2001 and is being conducted by the U.S. Geological Survey (USGS) in cooperation with the California State Water Resources Control Board (SWRCB). The San Fernando-San Gabriel study was designed to provide a spatially unbiased assessment of raw ground-water quality within SFSG, as well as a statistically consistent basis for comparing water quality throughout California. Samples were collected from 52 wells in Los Angeles County. Thirty-five of the wells were selected using a spatially distributed, randomized grid-based method to provide statistical representation of the study area (grid wells), and seventeen wells were selected to aid in the evaluation of specific water-quality issues or changes in water chemistry along a historic ground-water flow path (understanding wells). The ground-water samples were analyzed for a large number of synthetic organic constituents [volatile organic compounds (VOCs), pesticides and pesticide degradates], constituents of special interest [perchlorate, N-nitrosodimethylamine (NDMA), 1,2,3-trichloropropane (1,2,3-TCP), and 1,4-dioxane], naturally occurring inorganic constituents (nutrients, major and minor ions, and trace elements), radioactive constituents, and microbial indicators. Naturally occurring isotopes (tritium, and carbon-14, and stable isotopes of hydrogen, oxygen, and carbon), and dissolved noble gases also were measured to help identify the source and age of the sampled ground water. Quality-control samples (blanks, replicates, samples for matrix spikes) were collected at approximately one-fifth (11 of 52) of the wells, and the results for these samples were used to evaluate the quality of the data for the ground-water samples. Assessment of the quality-control results showed that the data had very little bias or variability and resulted in censoring of less than 0.7 percent (32 of 4,484 measurements) of the data collected for ground-water samples. This study did not attempt to evaluate the quality of water delivered to consumers; after withdrawal from the ground, water typically is treated, disinfected, or blended with other waters to maintain acceptable water quality. Regulatory thresholds apply to treated water that is served to the consumer, not to raw ground water. However, to provide some context for the results, concentrations of constituents measured in the raw ground water were compared with health-based thresholds established by the U.S. Environmental Protection Agency (USEPA) and California Department of Public Health (CDPH) and thresholds established for aesthetic concerns (secondary maximum contaminant levels, SMCL-CA) by CDPH. VOCs were detected in more than 90 percent (33 of 35) of grid wells. For all wells sampled for SFSG, nearly all VOC detections were below health-based thresholds, and most were less than one-tenth of the threshold values. Samples from seven wells had at least one detection of PCE, TCE, tetrachloromethane, NDMA, or 1,2,3-TCP at or above a health-based threshold. Pesticides were detected in about 90 percent (31 of 35) grid wells and all detections in samples from SFSG wells were below health-based thresholds. Major ions, trace elements, and nutrients in samples from 17 SFSG wells were all below health-based thresholds, with the exception of one detection of nitrate that was above the USEPA maximum contaminant level (MCL-US). With the exception of 14 samples having radon-222 above the proposed MCL-US, radioactive constituents were below health-based thresholds for 16 of the SFSG wells sampled. Total dissolved solids in 6 of the 24 SFSG wells that were sampled ha

Final report of the amended safety assessment of Dioscorea Villosa (Wild Yam) root extract.

PubMed

2004-01-01

Dioscorea Villosa (Wild Yam) Root Extract is an extract of the rhizomes of the wild yam, D. villosa. A manufacturing process was described in which cut up and ground rhizomes are combined with an eluant (e.g., oleyl alcohol), the plant material precipitated with addition of a miscible solvent, washed, and redissolved in the original eluant. The extract contains glycoside and steroidal saponins (< or =0.4%), diosgenin (< or =3.5%), alkaloids, tannins, phytosterols, and starch. Levels of heavy metals, 1,4-dioxane, chloroform, methylene chloride, trichloroethylene, and benzene are reported to be below limits of detection. Although only one use was reported to the U.S. Food and Drug Administration (in a body and hand preparation), industry reported uses in body and hand creams, lotions, powders, and sprays at a concentration of 0.00001% (equivalent to 0.000002% plant solids), and in moisturizing creams, lotions, powders, and sprays at concentrations up to 15% (equivalent to 0.5% plant solids). Preparations fromD. villosaare used in herbal medicine for treatment of a variety of ailments and by the pharmaceutical industry in the preparation of steroids. Using Dioscorea Villosa (Wild Yam) Root Extract prepared via a specified process, it is possible to produce a stable extract with a narrow range of diosgenin content. The extract produced using this methodology was tested in acute and short-term toxicity tests, dermal irritation tests, a sensitization test, an ocular irritation test, a rat uterotropic assay, and genotoxicity tests. An acute oral toxicity test produced hypoactivity, piloerection, and dyspnea and a death in 1 of 10 rats at 2 g/kg using the specified extract, but no toxicity in rats given 0.5 g/kg. A dermal toxicity test using the specified extract demonstrated no acute toxicity in rats. Both a 7-day local tolerance test and a 28-day dermal toxicity test in rats produced no significant adverse effects at the maximum tested concentration of 10%. A single application of undiluted extract to the intact and abraded skin of rabbits produced sufficient irritation for the test material to be rated"irritant,"but a 10% dilution was not irritating. Undiluted extract was only mildly irritating to the conjuctiva of the rabbit eye; irritation in the iris and cornea was mild and transient. Undiluted extract was not irritating during the induction phase of a guinea pig sensitization study, nor did challenge with a 25% dilution elicit any sensitization. The specified extract at concentrations up to 500 mg/kg/day did not have any estrogenic activity in the juvenile rat uterotrophic assay. Genotoxicity assays in bacterial and mammalian systems were negative, except that Ames test strain TA 1537 was positive at one dose level using the plate incorporation method, but not using a preincubation method. Although the concentration at which the actual plant extract is used in cosmetic products is low, one of the primary safety concerns with this plant extract is the possible metabolic/endocrine activity, e.g., estrogen-like or progesterone-like activity as a result of the presence of small amounts of plant phytosterols such as diosgenin. Extracts prepared as described in this safety assessment, with an upper limit of 3.5% diosgenin, did not have any estrogenic activity, demonstrating that it is possible to produce material that does not present this specific safety concern. Although extracts from pesticide-free plants were not considered genotoxic and it was the view of the Cosmetic Ingredient Review (CIR) Expert Panel that there do not appear to be any components that could be carcinogenic, pesticide residues could raise this issue. It was urged that manufacturers limit pesticide residues to the limit previously used for lanolin of not more than 40 ppm (with not more than 10 ppm for any one residue). Based on these data, it was concluded that Dioscorea Villosa (Wild Yam) Root Extract is safe as used in cosmetic formulations. This conclusion regarding safety, however, is valid only for extracts prepared in a manner that produces a similar chemical profile as that described in this report, particularly as regards diosgenin. Extracts not prepared in a manner that produces a similar chemical profile would be considered safe if they have a similar safety test profile.

Coupling of Plasmas and Liquids

NASA Astrophysics Data System (ADS)

Lindsay, Alexander David

Plasma-liquids have exciting applications to several important socioeconomic areas, including agriculture, water treatment, and medicine. To realize their application potential, the basic physical and chemical phenomena of plasma-liquid systems must be better understood. Additionally, system designs must be optimized in order to maximize fluxes of critical plasma species to the liquid phase. With objectives to increase understanding of these systems and optimize their applications, we have performed both comprehensive modeling and experimental work. To date, models of plasma-liquids have focused on configurations where diffusion is the dominant transport process in both gas and liquid phases. However, convection plays a key role in many popular plasma source designs, including jets, corona discharges, and torches. In this dissertation, we model momentum, heat, and neutral species mass transfer in a convection-dominated system based on a corona discharge. We show that evaporative cooling produced by gas-phase convection can lead to a significant difference between gas and liquid phase bulk temperatures. Additionally, convection induced in the liquid phase by the gas phase flow substantially increases interfacial mass transfer of hydrophobic species like NO and NO2. Finally, liquid kinetic modeling suggests that concentrations of highly reactive species like OH and ONOOH are several orders of magnitude higher at the interface than in the solution bulk. Subsequent modeling has focused on coupling discharge physics with species transport at and through the interface. An assumption commonly seen in the literature is that interfacial loss coefficients of charged species like electrons are equal to unity. However, there is no experimental evidence to either deny or support this assumption. Without knowing the true interfacial behavior of electrons, we have explored the effects on key plasma-liquid variables of varying interfacial parameters like the electron and energy surface loss coefficients. Within a reasonable range for these parameters, we have demonstrated that the electron density on the gas phase side of the interface can vary by orders of magnitude. Significant effects can also be seen on the gas phase interfacial electron energy. Electron density and energy will play important roles in determining gas phase chemistry in more complex future models; this will in turn feed back into the liquid phase chemistry. To remove this uncertainty in interfacial behavior, we recommend finer scale atomistic or molecular dynamics simulations. Efficient coupling of the highly non-linear discharge physics equations to liquid transport required creation of a new simulation code named Zapdos, built on top of the MOOSE framework. The operation and capabilities of the code are described in this work. Moreover, changes made to the MOOSE framework allowing coupling of physics across subdomain boundaries, necessary for plasma-liquid coupling, are also detailed. In the latter half of this work, we investigate experimental optimization and characterization of plasma-liquid interactions surrounding a unique very high frequency (VHF) plasma discharge. Several geometric configurations are considered. In the most promising set-up, the discharge is pointed upwards and water is pumped through the source's inner conductor until it forms a milimeter thick water layer on top of the powered electrode. This maximizes the amount of charged and neutral species flux received by the aqueous phase as well as the amount of water vapor created in the gas phase. Additionally, the configuration eliminates electrode damage by providing an infinitely renewable liquid surface layer. The presence of large amounts of water vapor and OH radicals is confirmed by optical emission and broadband absorption spectroscopy. Characterization of liquid phase species like NO-3 , NO-2 , and H2O2 is carried out through ion chromatography (IC) and colorimetric measurements. After detailing the design and characterization of our plasma-liquid systems, we illustrate their applications to plant fertilization and wastewater disinfection. In a four-week collaborative experiment with the NCSU greenhouse, plants that received plasma-treated water grew significantly larger than plants that received tap water. This is directly attributable to the approximately hundred mg/L of NO-3 dissolved into solution by the plasma. The VHF source also proved effective at removing several aqueous contaminants designated harmful to humans by the EPA. Air plasma treatment of solutions contaminated with 1,4-dioxane showed log reduction times competitive with other advanced oxidative processes (AOP). Argon treatment of dixoane was an order of magnitude more effective in terms of log reduction time, although the associated costs are significantly higher. Perfluorooctanesulfonic acid (PFOS) proved resistant to several VHF design iterations. However, the water electrode design introduced in the passage above achieved a log reduction in low level PFOS concentrations over the course of twenty five minutes, suggesting that it may be viable as an advanced technology for degradation of persistent perfluorinated compounds. (Abstract shortened by ProQuest.).

Synthesis, characterization, and properties of peroxo-based oxygen-rich compounds for potential use as greener high energy density materials

NASA Astrophysics Data System (ADS)

Gamage, Nipuni-Dhanesha Horadugoda

One main aspect of high energy density material (HEDM) design is to obtain greener alternatives for HEDMs that produce toxic byproducts. Primary explosives lead azide, lead styphnate, and mercury fulminate contain heavy metals that cause heavy metal poisoning. Leaching of the widely used tertiary explosive NH4ClO4 into groundwater has resulted in human exposure to ClO4-- ions, which cause disruptions of thyroid related metabolic pathways and even thyroid cancer. Many research efforts to find replacements have gained little success. Thus, there is a need for greener HEDMs. Peroxo-based oxygen-rich compounds are proposed as a potential new class of greener HEDMs due to the evolution of CO2 and/or CO, H2O, and O 2 as the main decomposition products. Currently, triacetone triperoxide (TATP), diacetone diperoxide (DADP), hexamethylene triperoxide diamine (HMTD), and methyl ethyl ketone peroxide (MEKP) are the only well-studied highly energetic peroxides. However, due to their high impact and friction sensitivities, low thermal stabilities, and low detonation velocities they have not found any civil or military HEDM applications. In this dissertation research, we have synthesized and fully characterized four categories of peroxo-based compounds: tert-butyl peroxides, tert-butyl peroxy esters, hydroperoxides, and peroxy acids to perform a systematic study of their sensitivities and the energetic properties for potential use as greener HEDMs. tert-Butyl peroxides were not sensitive to impact, friction, or electrostatic spark. Hence, tert-butyl peroxides can be described as fairly safe peroxo-based compounds to handle. tert-Butyl peroxy esters were all surprisingly energetic (4896--6003 m/s), despite the low oxygen and nitrogen contents. Aromatic tert -butyl peroxy esters were much lower in impact and friction sensitivities with respect to the known peroxo-based explosives. These are among the first low sensitivity peroxo-based compounds that can be categorized as secondary HEDMs. Oxygen-rich (0.80--1.00) geminal hydroperoxides have detonation velocities in the range of 6150--7130 m/s. These impressive detonation velocities are greater than the detonation velocities of the known peroxo-based explosives. The highest detonation velocity (7130 m/s) was obtained for 1,4-bis(dihydroperoxymethyl)benzene, which has the highest crystalline density (1.648 g/cm3). This detonation velocity is greater than the secondary explosive 2,4,6-trinitrotoluene (TNT). The sensitivities of these oxygen-rich geminal hydroperoxides are lower than the known peroxo-based explosives due to the O--H•••O hydrogen bonds and O•••O contacts, which stabilize the weak O--O bonds in the crystalline lattice. They could be useful as primary HEDMs. Dihydroperoxy dioxane and dioxolanes have impressive detonation velocities in the range of 6350--6694 m/s. However, their extremely high sensitivities render them unsafe for HEDM applications. Interestingly, hydroperoxy dioxanol and dioxolanols also have high detonation velocities in the range of 6100--6461 m/s even with the lower oxygen contents. The hydroperoxy compounds with one less O--O bond were much less sensitive than the dihydroperoxy compounds. These hydroperoxy compounds could be useful as primary HEDMs. We observed that the ring strain was useful in increasing the detonation velocities, since it led to compounds with higher crystalline densities. However, increasing the steric strain using bulky groups led to lower crystalline densities and lower detonation velocities. Higher steric strain not only resulted in higher sensitivities but also lower thermal stabilities. Peroxy acids have high detonation velocities in the range of 5262--7885 m/s. The detonation velocity of 3,5-dinitrobenzoperoxoic acid (7217 m/s) was the highest detonation velocity obtained for the peroxo-based compounds synthesized in our study, which is greater than the detonation velocity of TNT. The detonation velocity of 2,4,6-trinitrobenzoperoxoic acid (7885 m/s) is close to the detonation velocity of the secondary high explosive 1,3,5-trinitroperhydro-1,3,5-triazine (RDX). Peroxy acids have surprisingly low impact and friction sensitivities that are well below the known peroxo-based explosives TATP, DADP, HMTD, and MEKP. Based on the crystal structure of 3,5-dinitrobenzoperoxoic acid, the low sensitivities can be attributed to the stabilization of the weak O--O bonds in the crystalline lattice by O--H•••O hydrogen bonds and O•••O short contacts. These are the first peroxo-based oxygen-rich compounds that can be useful as secondary HEDMs. The ease of synthesis in high yields with minimum synthetic manipulations, storability, and high thermal stabilities are all advantageous properties of peroxy acids for their use as HEDMs. Through this work, we have gained a wealth of fundamental information about the structures and energetic materials properties of a large family of peroxo-based compounds. Solid state intermolecular interactions were useful to understand the impact and friction sensitivities. The safe peroxy O:C ratio was found to be approximately 1.00. However, the oxygen contents could be further increased with more stable nitro and hydroxy groups. Highly attractive low sensitivity peroxo-based compounds were obtained with impressive detonation performances for potential use as greener primary and secondary HEDMs.