Analysis of Discontinuity Induced Bifurcations in a Dual Input DC-DC Converter

NASA Astrophysics Data System (ADS)

Giaouris, Damian; Banerjee, Soumitro; Mandal, Kuntal; Al-Hindawi, Mohammed M.; Abusorrah, Abdullah; Al-Turki, Yusuf; El Aroudi, Abdelali

DC-DC power converters with multiple inputs and a single output are used in numerous applications where multiple sources, e.g. two or more renewable energy sources and/or a battery, feed a single load. In this work, a classical boost converter topology with two input branches connected to two different sources is chosen, with each branch independently being controlled by a separate peak current mode controller. We demonstrate for the first time that even though this converter is similar to other well known topologies that have been studied before, it exhibits many complex nonlinear behaviors that are not found in any other standard PWM controlled power converter. The system undergoes period incrementing cascade as a parameter is varied, with discontinuous hard transitions between consecutive periodicities. We show that the system can be described by a discontinuous map, which explains the observed bifurcation phenomena. The results have been experimentally validated.

An efficient high-frequency analysis of modal reflection and transmission coefficients for a class of waveguide discontinuities

NASA Technical Reports Server (NTRS)

Pathak, P. H.; Altintas, A.

1988-01-01

A high-frequency analysis of electromagnetic modal reflection and transmission coefficients is presented for waveguide discontinuities formed by joining different waveguide sections. The analysis uses an extended version of the concept of geometrical theory of diffraction based equivalent edge currents in conjunction with the reciprocity theorem to describe interior scattering effects. If the waveguide modes and their associated modal rays can be found explicitly, general two- and three-dimensional waveguide geometries can be analyzed. Expressions are developed for two-dimensional reflection and transmission coefficients. Numerical results are given for a flanged, semi-infinite parallel plate waveguide and for the junction between two linearly tapered waveguides.

Forward and inverse modeling for jovian seismology

NASA Astrophysics Data System (ADS)

Jackiewicz, Jason; Nettelmann, Nadine; Marley, Mark; Fortney, Jonathan

2012-08-01

Jupiter is expected to pulsate in a spectrum of acoustic modes and recent re-analysis of a spectroscopic time series has identified a regular pattern in the spacing of the frequencies (Gaulme, P., Schmider, F.-X., Gay, J., Guillot, T., Jacob, C. [2011]. Astron. Astrophys. 531, A104). This exciting result can provide constraints on gross jovian properties and warrants a more in-depth theoretical study of the seismic structure of Jupiter. With current instrumentation, such as the SYMPA instrument (Schmider, F.X. [2007]. Astron. Astrophys. 474, 1073-1080) used for the Gaulme et al. (Gaulme, P., Schmider, F.-X., Gay, J., Guillot, T., Jacob, C. [2011]. Astron. Astrophys. 531, A104) analysis, we assume that, at minimum, a set of global frequencies extending up to angular degree ℓ=25 could be observed. In order to identify which modes would best constraining models of Jupiter's interior and thus help motivate the next generation of observations, we explore the sensitivity of derived parameters to this mode set. Three different models of the jovian interior are computed and the theoretical pulsation spectrum from these models for ℓ⩽25 is obtained. We compute sensitivity kernels and perform linear inversions to infer details of the expected discontinuities in the profiles in the jovian interior. We find that the amplitude of the sound-speed jump of a few percent in the inner/outer envelope boundary seen in two of the applied models should be reasonably inferred with these particular modes. Near the core boundary where models predict large density discontinuities, the location of such features can be accurately measured, while their amplitudes have more uncertainty. These results suggest that this mode set would be sufficient to infer the radial location and strength of expected discontinuities in Jupiter's interior, and place strong constraints on the core size and mass. We encourage new observations to detect these jovian oscillations.

Effect of adhesive interleaving and discontinuous plies on failure of composite laminates subject to transverse normal loads

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.

1989-01-01

Results of a series of tests to determine the effects of adhesive interleaving and discontinuous plies (plies with end-to-end gaps) on the displacements, failure loads and failure modes of graphite-epoxy laminates subjected to transverse normal loads are presented. Adhesive interleaving can be used to contain local damage within a group of plies, i.e., to arrest crack propagation on the interlaminate level, and it can increase the amount of normal displacement the laminate can withstand before failure. However, the addition of adhesive interleaving to a laminate does not significantly increase its load carrying capability. A few discontinuous plies in a laminate can reduce the normal displacement and load at failure by 10 to 40 percent compared to a laminate with no discontinuous plies, but the presence of the ply discontinuities does not generally change the failure location or the failure mode of the laminate.

Resonant power processors. I - State plane analysis

NASA Technical Reports Server (NTRS)

Oruganti, R.; Lee, F. C.

1984-01-01

State-plane techniques in conjunction with piecewise-linear analysis is employed to study the steady-state and transient characteristics of a series resonant converter. With the direct viewing of the resonant tank energy and the device switching instants, the state portrayal provides unique insights into the complex behavior of the converter. Operation of the converter under both continuous and discontinuous current modes and at frequencies both below and above resonant frequency are discussed.

Monolithic single mode interband cascade lasers with wide wavelength tunability

NASA Astrophysics Data System (ADS)

von Edlinger, M.; Weih, R.; Scheuermann, J.; Nähle, L.; Fischer, M.; Koeth, J.; Kamp, M.; Höfling, S.

2016-11-01

Monolithic two-section interband cascade lasers offering a wide wavelength tunability in the wavelength range around 3.7 μm are presented. Stable single mode emission in several wavelength channels was realized using the concept of binary superimposed gratings and two-segment Vernier-tuning. The wavelength selective elements in the two segments were based on specially designed lateral metal grating structures defined by electron beam lithography. A dual-step dry etch process provided electrical separation between the segments. Individual current control of the segments allowed wavelength channel selection as well as continuous wavelength tuning within channels. A discontinuous tuning range extending over 158 nm in up to six discrete wavelength channels was achieved. Mode hop free wavelength tuning up to 14 nm was observed within one channel. The devices can be operated in continuous wave mode up to 30 °C with the output powers of 3.5 mW around room temperature.

Modeling Progressive Damage Using Local Displacement Discontinuities Within the FEAMAC Multiscale Modeling Framework

NASA Technical Reports Server (NTRS)

Ranatunga, Vipul; Bednarcyk, Brett A.; Arnold, Steven M.

2010-01-01

A method for performing progressive damage modeling in composite materials and structures based on continuum level interfacial displacement discontinuities is presented. The proposed method enables the exponential evolution of the interfacial compliance, resulting in unloading of the tractions at the interface after delamination or failure occurs. In this paper, the proposed continuum displacement discontinuity model has been used to simulate failure within both isotropic and orthotropic materials efficiently and to explore the possibility of predicting the crack path, therein. Simulation results obtained from Mode-I and Mode-II fracture compare the proposed approach with the cohesive element approach and Virtual Crack Closure Techniques (VCCT) available within the ABAQUS (ABAQUS, Inc.) finite element software. Furthermore, an eccentrically loaded 3-point bend test has been simulated with the displacement discontinuity model, and the resulting crack path prediction has been compared with a prediction based on the extended finite element model (XFEM) approach.

Revitalizing the drug pipeline: AntibioticDB, an open access database to aid antibacterial research and development.

PubMed

Farrell, L J; Lo, R; Wanford, J J; Jenkins, A; Maxwell, A; Piddock, L J V

2018-06-11

The current state of antibiotic discovery, research and development is insufficient to respond to the need for new treatments for drug-resistant bacterial infections. The process has changed over the last decade, with most new agents that are in Phases 1-3, or recently approved, having been discovered in small- and medium-sized enterprises or academia. These agents have then been licensed or sold to large companies for further development with the goal of taking them to market. However, early drug discovery and development, including the possibility of developing previously discontinued agents, would benefit from a database of antibacterial compounds for scrutiny by the developers. This article describes the first free, open-access searchable database of antibacterial compounds, including discontinued agents, drugs under pre-clinical development and those in clinical trials: AntibioticDB (AntibioticDB.com). Data were obtained from publicly available sources. This article summarizes the compounds and drugs in AntibioticDB, including their drug class, mode of action, development status and propensity to select drug-resistant bacteria. AntibioticDB includes compounds currently in pre-clinical development and 834 that have been discontinued and that reached varying stages of development. These may serve as starting points for future research and development.

Experimental and Numerical Analysis of Performance Discontinuity of a Pump-Turbine under Pumping Mode

NASA Astrophysics Data System (ADS)

Zhang, X.; Burgstaller, R.; Lai, X.; Gehrer, A.; Kefalas, A.; Pang, Y.

2016-11-01

The performance discontinuity of a pump-turbine under pumping mode is harmful to stable operation of units in hydropower station. In this paper, the performance discontinuity phenomenon of the pump-turbine was studied by means of experiment and numerical simulation. In the experiment, characteristics of the pump-turbine with different diffuser vane openings were tested in order to investigate the effect of pumping casing to the performance discontinuity. While other effects such as flow separation and rotating stall are known to have an effect on the discontinuity, the present studied test cases show that prerotation is the dominating effect for the instability, positions of the positive slope of characteristics are almost the same in different diffuser vane opening conditions. The impeller has principal effect to the performance discontinuity. In the numerical simulation, CFD analysis of tested pump-turbine has been done with k-ω and SST turbulence model. It is found that the position of performance curve discontinuity corresponds to flow recirculation at impeller inlet. Flow recirculation at impeller inlet is the cause of the discontinuity of characteristics curve. It is also found that the operating condition of occurrence of flow recirculation at impeller inlet is misestimated with k-ω and SST turbulence model. Furthermore, the original SST model has been modified. We predict the occurrence position of flow recirculation at impeller inlet correctly with the modified SST turbulence model, and it also can improve the prediction accuracy of the pump- turbine performance at the same time.

High performance ripple feedback for the buck unity-power-factor rectifier

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lo, Y.W.; King, R.J.

1995-03-01

The buck unity-power-factor rectifier has harmonic-free input current with complete load regulation down to zero output voltage. A new ``nonlinear ripple feedback`` is proposed which exactly cancels the spoiling effect of dc-side current ripple on the low-distortion ac line current waveforms, even for large amounts of ripple. This cancellation is independent of operating point and readily implemented with analog hardware, thereby permitting economies in the design of the dc filter while maintaining harmonic-free operation. Both large-signal and incremental analyses of the rectifier are given. Confirming experimental results from a 1-kW 48-V isolated battery charger operating with current-ripple levels ranging frommore » 50% to discontinuous-conduction-mode operation are given.« less

Bridgeless SEPIC PFC Converter for Multistring LED Driver

NASA Astrophysics Data System (ADS)

Jha, Aman; Singh, Bhim

2018-05-01

This paper deals with Power Factor Correction (PFC) in Low Voltage High Current (LVHC) multi-string light emitting diode (LED) using a bridgeless (BL) single ended primary inductance converter (SEPIC). This application is designed for large area LED lighting with illumination control. A multi-mode LED dimming technique is used for the lighting control. The BL-SEPIC PFC converter is used as a load emulator for high power factor. The regulated low voltage from flyback converter is a source power to the synchronous buck converters for multi-string LED driver and forced cooling system for LED junction. The BL-SEPIC PFC converter inductor design is based on Discontinuous Inductor Current Modes (DICM) which provides good PFC at low cost. Test results are found quite satisfactory for universal input AC (90-265 V). There is significant improvement in the power factor and input current Total Harmonic Distortion (THD) with good margin of harmonic limits for lighting IEC 61000-3-2 Class C.

Modeling and analysis of fractional order DC-DC converter.

PubMed

Radwan, Ahmed G; Emira, Ahmed A; AbdelAty, Amr M; Azar, Ahmad Taher

2017-07-11

Due to the non-idealities of commercial inductors, the demand for a better model that accurately describe their dynamic response is elevated. So, the fractional order models of Buck, Boost and Buck-Boost DC-DC converters are presented in this paper. The detailed analysis is made for the two most common modes of converter operation: Continuous Conduction Mode (CCM) and Discontinuous Conduction Mode (DCM). Closed form time domain expressions are derived for inductor currents, voltage gain, average current, conduction time and power efficiency where the effect of the fractional order inductor is found to be strongly present. For example, the peak inductor current at steady state increases with decreasing the inductor order. Advanced Design Systems (ADS) circuit simulations are used to verify the derived formulas, where the fractional order inductor is simulated using Valsa Constant Phase Element (CPE) approximation and Generalized Impedance Converter (GIC). Different simulation results are introduced with good matching to the theoretical formulas for the three DC-DC converter topologies under different fractional orders. A comprehensive comparison with the recently published literature is presented to show the advantages and disadvantages of each approach. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Shocks and currents in stratified atmospheres with a magnetic null point

NASA Astrophysics Data System (ADS)

Tarr, Lucas A.; Linton, Mark

2017-08-01

We use the resistive MHD code LARE (Arber et al 2001) to inject a compressive MHD wavepacket into a stratified atmosphere that has a single magnetic null point, as recently described in Tarr et al 2017. The 2.5D simulation represents a slice through a small ephemeral region or area of plage. The strong gradients in field strength and connectivity related to the presence of the null produce substantially different dynamics compared to the more slowly varying fields typically used in simple sunspot models. The wave-null interaction produces a fast mode shock that collapses the null into a current sheet and generates a set of outward propagating (from the null) slow mode shocks confined to field lines near each separatrix. A combination of oscillatory reconnection and shock dissipation ultimately raise the plasma's internal energy at the null and along each separatrix by 25-50% above the background. The resulting pressure gradients must be balanced by Lorentz forces, so that the final state has contact discontinuities along each separatrix and a persistent current at the null. The simulation demonstrates that fast and slow mode waves localize currents to the topologically important locations of the field, just as their Alfvenic counterparts do, and also illustrates the necessity of treating waves and reconnection as coupled phenomena.

Modelling of Dynamic Rock Fracture Process with a Rate-Dependent Combined Continuum Damage-Embedded Discontinuity Model Incorporating Microstructure

NASA Astrophysics Data System (ADS)

Saksala, Timo

2016-10-01

This paper deals with numerical modelling of rock fracture under dynamic loading. For this end, a combined continuum damage-embedded discontinuity model is applied in finite element modelling of crack propagation in rock. In this model, the strong loading rate sensitivity of rock is captured by the rate-dependent continuum scalar damage model that controls the pre-peak nonlinear hardening part of rock behaviour. The post-peak exponential softening part of the rock behaviour is governed by the embedded displacement discontinuity model describing the mode I, mode II and mixed mode fracture of rock. Rock heterogeneity is incorporated in the present approach by random description of the rock mineral texture based on the Voronoi tessellation. The model performance is demonstrated in numerical examples where the uniaxial tension and compression tests on rock are simulated. Finally, the dynamic three-point bending test of a semicircular disc is simulated in order to show that the model correctly predicts the strain rate-dependent tensile strengths as well as the failure modes of rock in this test. Special emphasis is laid on modelling the loading rate sensitivity of tensile strength of Laurentian granite.

Hidden dynamics in models of discontinuity and switching

NASA Astrophysics Data System (ADS)

Jeffrey, Mike R.

2014-04-01

Sharp switches in behaviour, like impacts, stick-slip motion, or electrical relays, can be modelled by differential equations with discontinuities. A discontinuity approximates fine details of a switching process that lie beyond a bulk empirical model. The theory of piecewise-smooth dynamics describes what happens assuming we can solve the system of equations across its discontinuity. What this typically neglects is that effects which are vanishingly small outside the discontinuity can have an arbitrarily large effect at the discontinuity itself. Here we show that such behaviour can be incorporated within the standard theory through nonlinear terms, and these introduce multiple sliding modes. We show that the nonlinear terms persist in more precise models, for example when the discontinuity is smoothed out. The nonlinear sliding can be eliminated, however, if the model contains an irremovable level of unknown error, which provides a criterion for systems to obey the standard Filippov laws for sliding dynamics at a discontinuity.

A mechanism for magnetospheric substorms

NASA Technical Reports Server (NTRS)

Erickson, G. M.; Heinemann, M.

1994-01-01

Energy-principle analysis performed on two-dimensional, self-consistent solutions for magnetospheric convection indicates that the magnetosphere is unstable to isobaric (yet still frozen-in) fluctuations of plasma-sheet flux tubes. Normally, pdV work associated with compression maintains stability of the inward/outward oscillating normal mode. However, if Earth's ionosphere can provide sufficient mass flux, isobaric expansion of flux tubes can occur. The growth of a field-aligned potential drop in the near-Earth, midnight portion of the plasma sheet, associated with upward field-aligned currents responsible for the Harang discontinuity, redistributes plasma along field lines in a manner that destabilizes the normal mode. The growth of this unstable mode results in an out-of-equilibrium situation near the inner edge. When this occurs over a downtail extent comparable to the half-thickness of the plasma sheet, collapse ensues and forces thinning of the plasma sheet whereby conditions favorable to reconnection occur. This scenario for substorm onset is consistent with observed upward fluxes of ions, parallel potential drops, and observations of substorm onset. These observations include near Earth onset, pseudobreakups, the substorm current wedge, and local variations of plasma-sheet thickness.

An analysis toolbox to explore mesenchymal migration heterogeneity reveals adaptive switching between distinct modes

PubMed Central

Shafqat-Abbasi, Hamdah; Kowalewski, Jacob M; Kiss, Alexa; Gong, Xiaowei; Hernandez-Varas, Pablo; Berge, Ulrich; Jafari-Mamaghani, Mehrdad; Lock, John G; Strömblad, Staffan

2016-01-01

Mesenchymal (lamellipodial) migration is heterogeneous, although whether this reflects progressive variability or discrete, 'switchable' migration modalities, remains unclear. We present an analytical toolbox, based on quantitative single-cell imaging data, to interrogate this heterogeneity. Integrating supervised behavioral classification with multivariate analyses of cell motion, membrane dynamics, cell-matrix adhesion status and F-actin organization, this toolbox here enables the detection and characterization of two quantitatively distinct mesenchymal migration modes, termed 'Continuous' and 'Discontinuous'. Quantitative mode comparisons reveal differences in cell motion, spatiotemporal coordination of membrane protrusion/retraction, and how cells within each mode reorganize with changed cell speed. These modes thus represent distinctive migratory strategies. Additional analyses illuminate the macromolecular- and cellular-scale effects of molecular targeting (fibronectin, talin, ROCK), including 'adaptive switching' between Continuous (favored at high adhesion/full contraction) and Discontinuous (low adhesion/inhibited contraction) modes. Overall, this analytical toolbox now facilitates the exploration of both spontaneous and adaptive heterogeneity in mesenchymal migration. DOI: http://dx.doi.org/10.7554/eLife.11384.001 PMID:26821527

EXPERIMENTAL MEASUREMENT AND INTERPRETATION OF VOLT-AMPERE CURVES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gingrich, J.E.; Warner, C.; Weeks, C.C.

1962-07-01

Cylindrical and parallel-plane cesium vapor thermionic converters were used for obtaining volt-ampere curves for systematic variations of emitter, collector, and cesium reservoir temperatures, with electrode spacings ranging from a few to many mean free paths, and with space charge conditions varying from electron-rich to ion-rich. The resulting curves exhibit much variety. The saturation currents agree well with the data of Houston and Aamodt for the space charge neutralized, few-mean-free-path cases. Apparent'' saturation currents for space charge limited cases were observed and were always less than the currents predicted by Houston and Aamodt. Several discontinuities in slope were observed in themore » reverse current portion of the curves and these have tentatively been identified with volume ionization of atoms in both the ground and excited states. Similar processes may be important for obtaining the ignited mode. The methods used to measure static and dynamic volt-ampere curves are described. The use of a controlled-current load has yielded a negative resistance'' region in the curves which show the ignited mode. The curves obtained with poor current control do not show this phenomenon. Extinction is considered from the standpoint of Kaufmann' s criterion for stability. (auth)« less

Continuous and Discontinuous Galerkin Methods for a Scalable Three-Dimensional Nonhydrostatic Atmospheric Model: Limited-Area Mode

DTIC Science & Technology

2012-01-01

atmosphere model, Int. J . High Perform. Comput. Appl. 26 (1) (2012) 74–89. [8] J.M. Dennis, M. Levy, R.D. Nair, H.M. Tufo, T . Voran. Towards and efficient...26] A. Klockner, T . Warburton, J . Bridge, J.S, Hesthaven, Nodal discontinuous galerkin methods on graphics processors, J . Comput. Phys. 228 (21) (2009...mode James F. Kelly, Francis X. Giraldo ⇑ Department of Applied Mathematics, Naval Postgraduate School, Monterey, CA, United States a r t i c l e i n

Interface Instabilities in the Interstellar Medium

NASA Technical Reports Server (NTRS)

Hunter, J. H., Jr.; Siopis, C.; Whitaker, R. W.; Lovelace, R. V. E.

1995-01-01

In the present communication, we reexamine two limiting cases of star-forming mechanisms involving self-gravity, thermodynamics, and velocity fields, that we believe must be ubiquitous in the ISM -- the generally oblique collision of supersonic gas streams or turbulent eddies. The general case of oblique collisions has not yet been examined. However, two limiting cases have been studied in detail: (1) The head-on collision of two identical gas streams that form dense, cool accretion shocks that become unstable and may form Jeans mass clouds, which subsequently undergo collapse. (2) Linearly unstable tangential velocity discontinuities, which result in Kelvin-Helmholtz (K-H) instabilities and related phenomena. The compressible K-H instabilities exhibit rich and unexpected behaviors. Moreover a new thermal-dynamic (T-D) mode was discovered that arises from the coupling of the perturbed thermal behavior and the unperturbed flow. The T-D mode has the curious characteristic that it may be strongly unstable to interface modes when the global modes in either medium are absolutely thermally stable. In the present communication additional models of case 1 are described and discussed, and self-gravity is added in the linear theory of tangential discontinuities, case 2. We prove that self-gravity fundamentally changes the behavior of interfacial modes -- density discontinuities (or steps) are inherently unstable on roughly the free-fall timescale of the denser medium to perturbations of all wavelengths.

Quasi-radial modes of rotating stars in general relativity

NASA Astrophysics Data System (ADS)

Yoshida, Shin'ichirou; Eriguchi, Yoshiharu

2001-04-01

By using the Cowling approximation, quasi-radial modes of rotating general relativistic stars are computed along equilibrium sequences from non-rotating to maximally rotating models. The eigenfrequencies of these modes are decreasing functions of the rotational frequency. The eigenfrequency curve of each mode as a function of the rotational frequency has discontinuities, which arise from the avoided crossing with other curves of axisymmetric modes.

Dynamics of Intense Currents in the Solar Wind

NASA Astrophysics Data System (ADS)

Artemyev, Anton V.; Angelopoulos, Vassilis; Halekas, Jasper S.; Vinogradov, Alexander A.; Vasko, Ivan Y.; Zelenyi, Lev M.

2018-06-01

Transient currents in the solar wind are carried by various magnetic field discontinuities that contribute significantly to the magnetic field fluctuation spectrum. Internal instabilities and dynamics of these discontinuities are believed to be responsible for magnetic field energy dissipation and corresponding charged particle acceleration and heating. Accurate modeling of these phenomena requires detailed investigation of transient current formation and evolution. By examining such evolution using a unique data set compiled from observations of the same solar wind flow by two spacecraft at Earth’s and Mars’s orbits, we show that it consists of several processes: discontinuity thinning (decrease in thickness normalized by the ion inertial length), intensification of currents normalized to the proton thermal current (i.e., the product of proton charge, density, and thermal velocity), and increase in the compressional component of magnetic field variations across discontinuities. The significant proton temperature variation around most observed discontinuities indicates possible proton heating. Plasma velocity jumps across the discontinuities are well correlated with Alfvén velocity changes. We discuss possible explanations of the observed discontinuity evolution. We also compare the observed evolution with predictions of models describing discontinuity formation due to Alfvén wave steepening. Our results show that discontinuity modeling likely requires taking into account both the effects of nonlinear Alfvén wave dynamics and solar wind expansion.

The Harang discontinuity in auroral belt ionospheric currents.

NASA Technical Reports Server (NTRS)

Heppner, J. P.

1972-01-01

Discussion of the nature of a discontinuity in the ionospheric current of the auroral belt whose existence was suggested by Harang in 1946. Convection characteristics, time variability, and current continuity in the auroral belt are considered in a context of observations and arguments supporting the reality of Harang's discontinuity.

A 66pW Discontinuous Switch-Capacitor Energy Harvester for Self-Sustaining Sensor Applications

PubMed Central

Wu, Xiao; Shi, Yao; Jeloka, Supreet; Yang, Kaiyuan; Lee, Inhee; Sylvester, Dennis; Blaauw, David

2016-01-01

We present a discontinuous harvesting approach for switch capacitor DC-DC converters that enables ultra-low power energy harvesting. By slowly accumulating charge on an input capacitor and then transferring it to a battery in burst-mode, switching and leakage losses in the DC-DC converter can be optimally traded-off with the loss due to non-ideal MPPT operation. The harvester uses a 15pW mode controller, an automatic conversion ratio modulator, and a moving sum charge pump for low startup energy upon a mode switch. In 180nm CMOS, the harvester achieves >40% end-to-end efficiency from 113pW to 1.5μW with 66pW minimum input power, marking a >10× improvement over prior ultra-low power harvesters. PMID:28392977

A 66pW Discontinuous Switch-Capacitor Energy Harvester for Self-Sustaining Sensor Applications.

PubMed

Wu, Xiao; Shi, Yao; Jeloka, Supreet; Yang, Kaiyuan; Lee, Inhee; Sylvester, Dennis; Blaauw, David

2016-06-01

We present a discontinuous harvesting approach for switch capacitor DC-DC converters that enables ultra-low power energy harvesting. By slowly accumulating charge on an input capacitor and then transferring it to a battery in burst-mode, switching and leakage losses in the DC-DC converter can be optimally traded-off with the loss due to non-ideal MPPT operation. The harvester uses a 15pW mode controller, an automatic conversion ratio modulator, and a moving sum charge pump for low startup energy upon a mode switch. In 180nm CMOS, the harvester achieves >40% end-to-end efficiency from 113pW to 1.5μW with 66pW minimum input power, marking a >10× improvement over prior ultra-low power harvesters.

Dynamic origin of segment magnetization reversal in thin-film Penrose tilings

NASA Astrophysics Data System (ADS)

Montoncello, F.; Giovannini, L.; Farmer, B.; De Long, L.

2017-02-01

We investigate the low-frequency spin wave dynamics involved in the magnetization reversal of a Penrose P2 tiling using the dynamical matrix method. This system consists of a two-dimensional, connected wire network of elongated thin-film segments, whose complete reversal occurs as a cascade of successive local segment reversals. Using soft mode theory, we interpret the reversal of an individual segment as a first order magnetic transition, in which magnetization curve of the system suffers a small discontinuity. Near this discontinuity a specific mode of the spin wave spectrum goes soft (i.e., its frequency goes to zero), triggering a local instability of the magnetization. We show that this mode is localized, and is at the origin of the local reversal. We discuss the correlation of the mode spatial profile with the ;reversal mechanism;, which is the passage of a domain wall through the segment. This process differs from reversal in periodic square or honeycomb artificial spin ices, where a cascade of reversing segments (e.g., ;Dirac string;) follows an extended (though irregular) path across the sample; here the spatial distribution of successive segment reversals is discontinuous, but strictly associated with the area where a soft mode is localized. The migration of the localization area across the P2 tiling (during reversal in decreasing applied fields) depends on changes in the internal effective field map. We discuss these results in the context of spin wave localization due to the unique topology of the P2 tiling.

Stability of plasma cylinder with current in a helical plasma flow

NASA Astrophysics Data System (ADS)

Leonovich, Anatoly S.; Kozlov, Daniil A.; Zong, Qiugang

2018-04-01

Stability of a plasma cylinder with a current wrapped by a helical plasma flow is studied. Unstable surface modes of magnetohydrodynamic (MHD) oscillations develop at the boundary of the cylinder enwrapped by the plasma flow. Unstable eigenmodes can also develop for which the plasma cylinder is a waveguide. The growth rate of the surface modes is much higher than that for the eigenmodes. It is shown that the asymmetric MHD modes in the plasma cylinder are stable if the velocity of the plasma flow is below a certain threshold. Such a plasma flow velocity threshold is absent for the symmetric modes. They are unstable in any arbitrarily slow plasma flows. For all surface modes there is an upper threshold for the flow velocity above which they are stable. The helicity index of the flow around the plasma cylinder significantly affects both the Mach number dependence of the surface wave growth rate and the velocity threshold values. The higher the index, the lower the upper threshold of the velocity jump above which the surface waves become stable. Calculations have been carried out for the growth rates of unstable oscillations in an equilibrium plasma cylinder with current serving as a model of the low-latitude boundary layer (LLBL) of the Earth's magnetic tail. A tangential discontinuity model is used to simulate the geomagnetic tail boundary. It is shown that the magnetopause in the geotail LLBL is unstable to a surface wave (having the highest growth rate) in low- and medium-speed solar wind flows, but becomes stable to this wave in high-speed flows. However, it can remain weakly unstable to the radiative modes of MHD oscillations.

Eddy current inspection tool. [Patent application

DOEpatents

Petrini, R.R.; Van Lue, D.F.

1980-10-29

A miniaturized inspection tool, for testing and inspection of metal objects in locations with difficult accessibility, which comprises eddy current sensing equipment with a probe coil, and associated coaxial coil cable, oil energizing means, and circuit means responsive to impedance changes in the coil as effected by induced eddy currents in a test object to produce a data output signal proportional to such changes. The coil and cable are slideably received in the utility channel of the flexible insertion tube of a fiberoptic scope. The scope is provided with light transmitting and receiving fiberoptics for viewing through the flexible tube, and articulation means for articulating the distal end of the tube and permitting close control of coil placement relative to a test object. The eddy current sensing equipment includes a tone generator for generating audible signals responsive to the data output signal. In one selected mode of operation, the tone generator responsive to the output signal above a selected level generates a constant single frequency tone for signalling detection of a discontinuity and, in a second selected mode, generates a tone whose frequency is proportional to the difference between the output signal and a predetermined selected threshold level.

What are the control mechanisms of evenly-spaced parallel strike-slip faults? Insights from DEM modeling

NASA Astrophysics Data System (ADS)

Bonilla Sierra, V.; Donze, F. V.; Duriez, J.; Klinger, Y.; Scholtes, L.

2016-12-01

At the very early stages of a pure strike-slip fault zone formation, shear displacement along a deep buried parent fault produces a characteristic set of "evenly-spaced" strike-slip faults at the surface, e.g. Southern San Andreas, North Anatolian, Central Asian, and Northern Tibetan fault systems. This mode III fracture propagation is initiated by the rotation of the local principal stress at the tip of the parent discontinuity, generating twisted fractures with a helicoidal shape. In sandbox or clay-cake experiments used to reproduce these structures, it has been observed that the spacing and possibly the characteristic length of the fractures appearing at the surface are proportional to the overburden thickness of the deformed layer. Based on a Discrete Element Method (YADE DEM-Open Source), we have investigated the conditions controlling the linear relationships between the spacing of the surface "evenly-spaced" strike-slip discontinuities and the thickness of the deformed layer. Increasing the basement displacement of the model, a diffused shear zone appears first at the tip of the basal parent discontinuity. From this mist zone, localized and strongly interacting shear fractures start to propagate. This interaction process can generate complex internal structures: some fractures will propagate faster than their neighbors, modifying their close surrounding stress environment. Some propagating fractures can stop growing and asymmetrical fracture sets can be observed. This resulting hierarchical bifurcation process leads to a set of "en echelon" discontinuities appearing at the surface (Figure 1). In a pure strike-slip mode, fracture spacing is proportional to the thickness, with a ratio and a bifurcation mode controlled by the cohesion value at the first order. Depending on the Poisson's ratio value, which mainly controls the orientation of the discontinuities, this ratio can be affected at a lower degree. In presence of mixed-mode (transpression or transtension), these linear relationships disappear. Figure 1: Effects of the cohesion C and the thickness T of the deformed layer on the surface discontinuity pattern (a) T = Tref and C = Cref (b) T = Tref and C= 10×Cref (c) T = 2×Tref and C = Cref (d) T = 2×Tref and 10×Cref. The color code corresponds to the instantaneous velocity in the Y direction.

Testing theoretical models of subdwarf B stars using multicolor photometry

NASA Astrophysics Data System (ADS)

Reed, Mike; Baran, Andrzej; Ostensen, Roy; O'Toole, Simon

2012-08-01

Pulsating stars allow a direct investigation of their structure and evolutionary history from the evaluation of pulsation modes. However, the observed pulsation frequencies must first be identified with spherical harmonics (modes). For subdwarfs B (sdB) stars, such identifications using white light photometry currently have significant limitations. We intend to use multicolor photometry to identify pulsation modes and constrain structure models. We propose to observe the pulsating sdB star PG0154+182 (BI Ari) with our multicolor instrument GT Cam. Our observations will be compared with perturbative atmospheric models (BRUCE/KYLIE) to identify the pulsation modes. This is part of our NSF grant to obtain seismic tools to test structure and evolution models; constraining stellar parameters including total mass, envelope mass, internal composition discontinuities and internal rotation. During winter/spring 2012, we were allocated three runs on the 2.1 m to collect multicolor data on other promising pulsating subdwarf B stars as part of this work. Those runs were very successful, prompting our continued proposals. In addition, we will obtain 3-color data using MAIA on the Mercator Telescope (using guaranteed institutional time).

Sound diffraction at wall impedance discontinuities in a circular cylinder, investigated using Wiener-Hopf technique

NASA Technical Reports Server (NTRS)

Cho, Y. C.

1983-01-01

Rigorous solutions are presented for sound diffraction in a circular cylinder with axial discontinuities of the wall admittance (or impedance). Analytical expressions are derived for the reflection and the transmission coefficients for duct modes. The results are discussed quantitatively in the limits of small admittance shifts (delta) and of low frequencies (ka). One of the results is the low frequency behavior of the reflection coefficient R(o) sub 00 of the fundamental mode. For the mode of a hardwall duct reflected from the junction with a softwall duct, (R(o) sub oo yields - (1-square root of (ka) square root of (2/i delta)); this result is in contrast to the frequency dependence of the reflection from the open end of a hardwall duct, for which R(o) sub oo yields - 1-(ka) squared/2 .

Resistive dissipation and magnetic field topology in the stellar corona

NASA Technical Reports Server (NTRS)

Parker, E. N.

1993-01-01

Tangential discontinuities, or current sheets, in a magnetic field embedded in a fluid with vanishing resistivity are created by discontinuous fluid motion. Tangential discontinuities are also created when a magnetic field is allowed to relax to magnetostatic equilibrium after mixing by fluid motions (either continuous or discontinuous) into any but the simplest topologies. This paper shows by formal examples that the current sheets arising solely from discontinuous fluid motions do not contribute significantly to the dissipation of magnetic free energy when a small resistivity is introduced. Dissipation that is significant under coronal conditions occurs only by rapid reconnection, which arises when, and only when, the current sheets are required by the field topology. Hence it is topological dissipation that is primarily responsible for heating tenuous coronal gases in astronomical settings, whether the fluid displacements of the field are continuous or discontinuous.

Defect induced guided waves mode conversion

NASA Astrophysics Data System (ADS)

Wandowski, Tomasz; Kudela, Pawel; Malinowski, Pawel; Ostachowicz, Wieslaw

2016-04-01

This paper deals with analysis of guided waves mode conversion phenomenon in fiber reinforced composite materials. Mode conversion phenomenon may take place when propagating elastic guided waves interact with discontinuities in the composite waveguide. The examples of such discontinuities are sudden thickness change or delamination between layers in composite material. In this paper, analysis of mode conversion phenomenon is based on full wave-field signals. In the full wave-field approach signals representing propagation of elastic waves are gathered from dense mesh of points that span over investigated area of composite part. This allow to animate the guided wave propagation. The reported analysis is based on signals resulting from numerical calculations and experimental measurements. In both cases defect in the form of delamination is considered. In the case of numerical research, Spectral Element Method (SEM) is utilized, in which a mesh is composed of 3D elements. Numerical model includes also piezoelectric transducer. Full wave-field experimental measurements are conducted by using piezoelectric transducer for guided wave excitation and Scanning Laser Doppler Vibrometer (SLDV) for sensing.

Improved Transient and Steady-State Performances of Series Resonant ZCS High-Frequency Inverter-Coupled Voltage Multiplier Converter with Dual Mode PFM Control Scheme

NASA Astrophysics Data System (ADS)

Chu, Enhui; Gamage, Laknath; Ishitobi, Manabu; Hiraki, Eiji; Nakaoka, Mutsuo

The A variety of switched-mode high voltage DC power supplies using voltage-fed type or current-fed type high-frequency transformer resonant inverters using MOS gate bipolar power transistors; IGBTs have been recently developed so far for a medical-use X-ray high power generator. In general, the high voltage high power X-ray generator using voltage-fed high frequency inverter with a high voltage transformer link has to meet some performances such as (i) short rising period in start transient of X-ray tube voltage (ii) no overshoot transient response in tube voltage, (iii) minimized voltage ripple in periodic steady-state under extremely wide load variations and filament heater current fluctuation conditions of the X-ray tube. This paper presents two lossless inductor snubber-assisted series resonant zero current soft switching high-frequency inverter using a diode-capacitor ladder type voltage multiplier called Cockcroft-Walton circuit, which is effectively implemented for a high DC voltage X-ray power generator. This DC high voltage generator which incorporates pulse frequency modulated series resonant inverter using IGBT power module packages is based on the operation principle of zero current soft switching commutation scheme under discontinuous resonant current and continuous resonant current transition modes. This series capacitor compensated for transformer resonant power converter with a high frequency transformer linked voltage boost multiplier can efficiently work a novel selectively-changed dual mode PFM control scheme in order to improve the start transient and steady-state response characteristics and can completely achieve stable zero current soft switching commutation tube filament current dependent for wide load parameter setting values with the aid of two lossless inductor snubbers. It is proved on the basis of simulation and experimental results in which a simple and low cost control implementation based on selectively-changed dual-mode PFM for high-voltage X-ray DC-DC power converter with a voltage multiplier strategy has some specified voltage pattern tracking voltage response performances under rapid rising time and no overshoot in start transient tube voltage as well as the minimized steady-state voltage ripple in tube voltage.

A new continuous sliding mode control approach with actuator saturation for control of 2-DOF helicopter system.

PubMed

Sadala, S P; Patre, B M

2018-03-01

The 2-degree of freedom (DOF) helicopter system is a typical higher-order, multi-variable, nonlinear and strong coupled control system. The helicopter dynamics also includes parametric uncertainties and is subject to unknown external disturbances. Such complicated system requires designing a sophisticated control algorithm that can handle these difficulties. This paper presents a new robust control algorithm which is a combination of two continuous control techniques, composite nonlinear feedback (CNF) and super-twisting control (STC) methods. In the existing integral sliding mode (ISM) based CNF control law, the discontinuous term exhibits chattering which is not desirable for many practical applications. As the continuity of well known STC reduces chattering in the system, the proposed strategy is beneficial over the current ISM based CNF control law which has a discontinuous term. Two controllers with integral sliding surface are designed to control the position of the pitch and the yaw angles of the 2- DOF helicopter. The adequacy of this specific combination has been exhibited through general analysis, simulation and experimental results of 2-DOF helicopter setup. The acquired results demonstrate the good execution of the proposed controller regarding stabilization, following reference input without overshoot against actuator saturation and robustness concerning to the limited matched disturbances. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

State-plane analysis of parallel resonant converter

NASA Technical Reports Server (NTRS)

Oruganti, R.; Lee, F. C.

1985-01-01

A method for analyzing the complex operation of a parallel resonant converter is developed, utilizing graphical state-plane techniques. The comprehensive mode analysis uncovers, for the first time, the presence of other complex modes besides the continuous conduction mode and the discontinuous conduction mode and determines their theoretical boundaries. Based on the insight gained from the analysis, a novel, high-frequency resonant buck converter is proposed. The voltage conversion ratio of the new converter is almost independent of load.

Influence of Weathering Depth and Fracture Intensity to Cut-slope Movements

NASA Astrophysics Data System (ADS)

Yoon, W. S.; Choi, J. W.; Jeong, U.; Kim, J. H.

2003-04-01

Generally, Failure modes in cut slopes are triggered by combination of various failure factors which have different effects on failure modes according to ground condition. It is, therefore, important to identify the behavioural characteristic of cut slope in that they reflect the failure mechanism. From the careful field investigation for 373 road cuts along the national highway in Korea, we analysed various types of failure modes for different ground conditions. The ground conditions which control failure modes of cut slopes and their related failure factors are dependent on weathering (or soil) depth and intensity of discontinuities in cut slopes. Firstly, the ratio of the soil depth and slope height (soil depth ratio; SR) is important parameter to classify ground conditions into soil-like masses and rock masses. When a SR value is greater than 0.4, sliding failures on discontinuities do not occur. In this case, weathering condition, slope gradient and external rainfall play a key role on failure factors of cut-slope. The proposed 0.4, therefore, is the critical SR value to identify the soil-like masses and rock masses. Secondly, Intensity of discontinuities is expressed by block size ratio (BR), which is defined by the ratio of block size index (Ib; ISRM (1978)) and slope height. For a rock slope (SR<0.4), when BR is greater than 0.01, key failure modes in a cut slope are wedge sliding, fall and topple. In this case, attitudes and shear strength of discontinuities play an important role on behaviour of cut-slope. When BR is less than 0.01, however, behaviour of cut slope shows circular sliding and surface failure like soil-like mass. To sum up, we could divide the ground conditions in cut-slope into 3 classes on the basis of SR (soil depth ratio) and BR (block size ratio); JRM (joint rock mass), HRM (highly fractured rock mass) and SLM (soil-like mass). Moreover, to evaluate the stability of cut-slope reasonably, it needs new evaluating categories having different weighting factors for each ground condition.

Preferred flavors and reasons for e-cigarette use and discontinued use among never, current, and former smokers.

PubMed

Berg, Carla J

2016-03-01

To compare e-cigarette flavors preferred and reasons for use and discontinued use across never, current, and former e-cigarette users and cigarette smokers. We recruited 1567 participants aged 18-34 years through Facebook ads targeting tobacco users and nonusers in August 2014 to complete an online survey. We assessed tobacco use, preferred flavors, and reasons for e-cigarette use and discontinued use. Our sample was 49 % male, 87 % White; 56 % current cigarette smokers; and 53 % e-cigarette users. Current e-cigarette users used an average of 20.9 days in the past 30 (SD = 11.7) and 55.2 puffs/day (SD = 37.3). Compared to never and current smokers, former smokers used e-cigarettes more frequently (p's <0.001). Among users and nonusers, the most preferred was fruit flavors, and the most commonly reported reason for e-cigarette use was "they might be less harmful than cigarettes". The most endorsed reason for discontinued e-cigarette use was "using other tobacco products instead". Never, current, and former smokers had distinct reasons for e-cigarette use and discontinued use and differed in flavor preferences. Regulating marketing and flavors may impact e-cigarette uptake by young adults.

Nonlinear analysis of a family of LC tuned inverters. [dc to square wave circuits for power conditioning

NASA Technical Reports Server (NTRS)

Lee, F. C. Y.; Wilson, T. G.

1974-01-01

A family of four dc-to-square-wave LC tuned inverters are analyzed using singular point. Limit cycles and waveshape characteristics are given for three modes of oscillation: quasi-harmonic, relaxation, and discontinuous. An inverter in which the avalanche breakdown of the transistor emitter-to-base junction occurs is discussed and the starting characteristics of this family of inverters are presented. The LC tuned inverters are shown to belong to a family of inverters with a common equivalent circuit consisting of only three 'series' elements: a five-segment piecewise-linear current-controlled resistor, linear inductor, and linear capacitor.

Method for controlling brazing

DOEpatents

Hosking, F Michael [Albuquerque, NM; Hall, Aaron C [Albuquerque, NM; Givler, Richard C [Albuquerque, NM; Walker, Charles A [Albuquerque, NM

2006-08-01

A method for making a braze joint across a discontinuity in a work piece using alternating current. A filler metal is pre-placed at a location sufficiently close to the discontinuity such that, when an alternating current is applied across a work piece to heat the work piece and melt the filler metal, the filler metal is drawn into the discontinuity. The alternating current is maintained for a set residence time, generally less than 10 seconds and more particularly less than 3 seconds. The alternating current is then altered, generally by reducing the current and/or voltage such that the filler metal can solidify to form a braze joint of desired quality and thickness.

Global Discontinuity Structure of the Mantle Transition Zone from Finite-Frequency Tomography of SS Precursors

NASA Astrophysics Data System (ADS)

Guo, Z.; Zhou, Y.

2017-12-01

We report global structure of the 410-km and 660-km discontinuities from finite-frequency tomography using frequency-dependent traveltime measurements of SS precursors recorded at the Global Seismological Network (GSN). Finite-frequency sensitivity kernels for discontinuity depth perturbations are calculated in the framework of traveling-wave mode coupling. We parametrize the global discontinuities using a set of spherical triangular grid points and solve the tomographic inverse problem based on singular value decomposition. Our global 410-km and 660-km discontinuity models reveal distinctly different characteristics beneath the oceans and subduction zones. In general, oceanic regions are associated with a thinner mantle transition zone and depth perturbations of the 410-km and 660-km discontinuities are anti-correlated, in agreement with a thermal origin and an overall warm and dry mantle beneath the oceans. The perturbations are not uniform throughout the oceans but show strong small-scale variations, indicating complex processes in the mantle transition zone. In major subduction zones (except for South America where data coverage is sparse), depth perturbations of the 410-km and 660-km discontinuities are correlated, with both the 410-km and the 660-km discontinuities occurring at greater depths. The distributions of the anomalies are consistent with cold stagnant slabs just above the 660-km discontinuity and ascending return flows in a superadiabatic upper mantle.

Acid azo dye remediation in anoxic-aerobic-anoxic microenvironment under periodic discontinuous batch operation: bio-electro kinetics and microbial inventory.

PubMed

Venkata Mohan, S; Suresh Babu, P; Naresh, K; Velvizhi, G; Madamwar, Datta

2012-09-01

Functional behavior of anoxic-aerobic-anoxic microenvironment on azo dye (C.I. Acid black 10B) degradation was evaluated in a periodic discontinuous batch mode operation for 26 cycles. Dye removal efficiency and azo-reductase activity (30.50 ± 1 U) increased with each feeding event until 13th cycle and further stabilized. Dehydrogenase activity also increased gradually and stabilized (2.0 ± 0.2 μg/ml) indicating the stable proton shuttling between metabolic intermediates providing higher number of reducing equivalents towards dye degradation. Voltammetric profiles showed drop in redox catalytic currents during stabilized phase also supports the consumption of reducing equivalents towards dye removal. Change in Tafel slopes, polarization resistance and other bioprocess parameters correlated well with the observed dye removal and biocatalyst behavior. Microbial community analysis documented the involvement of specific organism pertaining to aerobic and facultative functions with heterotrophic and autotrophic metabolism. Integrating anoxic microenvironment with aerobic operation might have facilitated effective dye mineralization due to the possibility of combining redox functions. Copyright © 2012 Elsevier Ltd. All rights reserved.

Transactions of the Second All-Union Conference on Charged Particle Accelerators (Moscow, 11-18 November 1970). Volume 2

DTIC Science & Technology

1980-10-09

to the interruption/discontinu.Lty into y - higher than transition energy. Discontinuity can be removed, for example, by the introduction to special...stable acceleration mode in acccrdance with theory ri], is arranged/located with the negative detuning of rescnator (when its frequency higher than...TRANSLATION IS A RENDITION OF THE ORIGI. NAL FOREIGN TEXT WITHOUT ANY ANALYTICAL OR EDITORIAL COMMENT. STATEMENTS OR THEORIES PREPARED BY: ADVOCATED OR

Nonlinear control of magnetic bearings

NASA Technical Reports Server (NTRS)

Pradeep, A. K.; Gurumoorthy, R.

1994-01-01

In this paper we present a variety of nonlinear controllers for the magnetic bearing that ensure both stability and robustness. We utilize techniques of discontinuous control to design novel control laws for the magnetic bearing. We present in particular sliding mode controllers, time optimal controllers, winding algorithm based controllers, nested switching controllers, fractional controllers, and synchronous switching controllers for the magnetic bearing. We show existence of solutions to systems governed by discontinuous control laws, and prove stability and robustness of the chosen control laws in a rigorous setting. We design sliding mode observers for the magnetic bearing and prove the convergence of the state estimates to their true values. We present simulation results of the performance of the magnetic bearing subject to the aforementioned control laws, and conclude with comments on design.

Precision and reliability of periodically and quasiperiodically driven integrate-and-fire neurons.

PubMed

Tiesinga, P H E

2002-04-01

Neurons in the brain communicate via trains of all-or-none electric events known as spikes. How the brain encodes information using spikes-the neural code-remains elusive. Here the robustness against noise of stimulus-induced neural spike trains is studied in terms of attractors and bifurcations. The dynamics of model neurons converges after a transient onto an attractor yielding a reproducible sequence of spike times. At a bifurcation point the spike times on the attractor change discontinuously when a parameter is varied. Reliability, the stability of the attractor against noise, is reduced when the neuron operates close to a bifurcation point. We determined using analytical spike-time maps the attractor and bifurcation structure of an integrate-and-fire model neuron driven by a periodic or a quasiperiodic piecewise constant current and investigated the stability of attractors against noise. The integrate-and-fire model neuron became mode locked to the periodic current with a rational winding number p/q and produced p spikes per q cycles. There were q attractors. p:q mode-locking regions formed Arnold tongues. In the model, reliability was the highest during 1:1 mode locking when there was only one attractor, as was also observed in recent experiments. The quasiperiodically driven neuron mode locked to either one of the two drive periods, or to a linear combination of both of them. Mode-locking regions were organized in Arnold tongues and reliability was again highest when there was only one attractor. These results show that neuronal reliability in response to the rhythmic drive generated by synchronized networks of neurons is profoundly influenced by the location of the Arnold tongues in parameter space.

Identifying the factors underlying discontinuation of triptans.

PubMed

Wells, Rebecca E; Markowitz, Shira Y; Baron, Eric P; Hentz, Joseph G; Kalidas, Kavita; Mathew, Paul G; Halker, Rashmi; Dodick, David W; Schwedt, Todd J

2014-02-01

To identify factors associated with triptan discontinuation among migraine patients. It is unclear why many migraine patients who are prescribed triptans discontinue this treatment. This study investigated correlates of triptan discontinuation with a focus on potentially modifiable factors to improve compliance. This multicenter cross-sectional survey (n = 276) was performed at US tertiary care headache clinics. Headache fellows who were members of the American Headache Society Headache Fellows Research Consortium recruited episodic and chronic migraine patients who were current triptan users (use within prior 3 months and for ≥1 year) or past triptan users (no use within 6 months; prior use within 2 years). Univariate analyses were first completed to compare current triptan users to past users for: migraine characteristics, other migraine treatments, triptan education, triptan efficacy, triptan side effects, type of prescribing provider, Migraine Disability Assessment (MIDAS) scores and Beck Depression Inventory (BDI) scores. Then, a multivariable logistic regression model was selected from all possible combinations of predictor variables to determine the factors that best correlated with triptan discontinuation. Compared with those still using triptans (n = 207), those who had discontinued use (n = 69) had higher rates of medication overuse (30 vs. 18%, P = .04) and were more likely to have ever used opioids for migraine treatment (57 vs. 38%, P = .006) as well as higher MIDAS (mean 63 vs. 37, P = .001) and BDI scores (mean 10.4 vs. 7.4, P = .009). Compared with discontinued users, current triptan users were more likely to have had their triptan prescribed by a specialist (neurologist, headache specialist, or pain specialist) (74 vs. 54%, P = .002) and were more likely to report headache resolution (53 vs. 14%, P < .001) or a reduction in pain intensity (71 vs. 28%, P < .001) most of the time from their triptan. On a 1-5 scale (1 = disagree, 5 = agree), triptan users felt they had more: control over their migraine attacks (2.9 vs. 2.1), confidence in their prescribing provider (4.5 vs. 4.0), and were more educated about triptan use (4.2 vs. 3.7) compared with triptan discontinuers (P < .001 for all comparisons). Although both current and prior users reported similar rates of side effects (48 vs. 43%, P = .44), of those who discontinued use, the main reasons were for lack of effect (44%) and side effects (29%). Our multivariable modeling revealed that the strongest correlate of triptan discontinuation was lack of efficacy (odds ratio = 17, 95% confidence interval [8.8, 33.0]). Other factors associated with discontinuation included MIDAS > 24 (2.6, [1.5, 4.6]), BDI >4 (2.5, [1.4, 4.5]), and a history of ever using opioids for migraine therapy (2.2, [1.3, 3.8]). Having a triptan prescribed by a specialist and using at least 1 other abortive medication with the triptan were associated with a decreased likelihood of triptan discontinuation (0.41, [0.2-0.7] and 0.44 [0.3, 0.8], respectively). As expected, discontinuation was most correlated with lack of efficacy, but other important factors associated with those who had discontinued use included greater migraine-related disability, depression, and the use of opioids for migraine attacks. Compared with patients who had discontinued triptans, current triptan users felt more: educated about their triptan, control over their migraine attacks, and confidence in their prescribing provider. Current triptan users had their triptan prescribed by a specialist and used other abortive medications with their triptan more often compared with patients who had discontinued triptans. Given the cross-sectional nature of this study, we cannot determine if these factors contributed to triptan discontinuation or reflect the impact of such discontinuation. Interventions that address modifiable risk factors for triptan discontinuation may decrease the likelihood of triptan discontinuation and thus improve overall migraine control. Because lack of efficacy was most strongly associated with triptan discontinuation, future research should determine why triptans are effective for some patients but not others. © 2013 American Headache Society.

The Application of Deterministic Spectral Domain Method to the Analysis of Planar Circuit Discontinuities on Open Substrates

DTIC Science & Technology

1990-08-01

the spectral domain is extended to include the effects of two-dimensional, two-component current flow in planar transmission line discontinuities 6n...PROFESSOR: Tatsuo Itoh A deterministic formulation of the method of moments carried out in the spectral domain is extended to include the effects of...two-dimensional, two- component current flow in planar transmission line discontinuities on open substrates. The method includes the effects of space

Slots in dielectric image line as mode launchers and circuit elements

NASA Astrophysics Data System (ADS)

Solbach, K.

1981-01-01

A planar resonator model is used to investigate slots in the ground plane of dielectric image lines. An equivalent circuit representation of the slot discontinuity is obtained, and the launching efficiency of the slot as a mode launcher is analyzed. Slots are also shown to be useful in the realization of dielectric image line array antennas. It is found that the slot discontinuity can be shown as a T-junction of the dielectric image line and a metal waveguide. The launching efficiency is found to increase with the dielectric constant of the dielectric image line, exhibiting a maximum value for guides whose height is slightly less than half a wavelength in the dielectric medium. The measured launching efficiencies of low permittivity dielectric image lines are found to be in good agreement with calculated values

GNuMe: A Galerkin-based Numerical Modeliing Environment for modeling geophysical fluid dynamics applications ranging from the Atmosphere to the Ocean

NASA Astrophysics Data System (ADS)

Giraldo, Francis; Abdi, Daniel; Kopera, Michal

2017-04-01

We have built a Galerkin-based Numerical Modeling Environment (GNuMe) for non hydrostatic atmospheric and ocean processes. GNuMe uses continuous Galerkin and Discontinuous Galerkin (CG/DG) discetizations as well as non-conforming adaptive mesh refinement (AMR), along with advanced time-integration methods that exploits both CG/DG and AMR capabilities. GNuMe currently solves the compressible and incompressible Navier-Stokes equations, the shallow water equations (with wetting and drying), and work is underway for inclusion of other types of equations. Moreover, GNuMe can run in both 2D and 3D modes on any type of accelerator hardware such as Nvidia GPUs and Intel KNL, and on standard X86 cores. In this talk, we shall present representative solutions obtained with GNuMe and will discuss where we think such a modeling framework could fit within standard Earth Systems Models. For further information on GNuMe please visit: http://frankgiraldo.wixsite.com/mysite/gnume.

Physics-based process model approach for detecting discontinuity during friction stir welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shrivastava, Amber; Pfefferkorn, Frank E.; Duffie, Neil A.

2015-02-12

The goal of this work is to develop a method for detecting the creation of discontinuities during friction stir welding. This in situ weld monitoring method could significantly reduce the need for post-process inspection. A process force model and a discontinuity force model were created based on the state-of-the-art understanding of flow around an friction stir welding (FSW) tool. These models are used to predict the FSW forces and size of discontinuities formed in the weld. Friction stir welds with discontinuities and welds without discontinuities were created, and the differences in force dynamics were observed. In this paper, discontinuities weremore » generated by reducing the tool rotation frequency and increasing the tool traverse speed in order to create "cold" welds. Experimental force data for welds with discontinuities and welds without discontinuities compared favorably with the predicted forces. The model currently overpredicts the discontinuity size.« less

Adherence, persistence, and medication discontinuation in patients with attention-deficit/hyperactivity disorder – a systematic literature review

PubMed Central

Gajria, Kavita; Lu, Mei; Sikirica, Vanja; Greven, Peter; Zhong, Yichen; Qin, Paige; Xie, Jipan

2014-01-01

Untreated attention-deficit/hyperactivity disorder (ADHD) can lead to substantial adverse social, economic, and emotional outcomes for patients. The effectiveness of current pharmacologic treatments is often reduced, due to low treatment adherence and medication discontinuation. This current systematic literature review analyzes the current state of knowledge surrounding ADHD medication discontinuation, focusing on: 1) the extent of patient persistence; 2) adherence; and 3) the underlying reasons for patients’ treatment discontinuation and how discontinuation rates and reasons vary across patient subgroups. We selected 91 original studies (67 with persistence/discontinuation results, 26 with adherence results, and 41 with reasons for discontinuation, switching, or nonadherence) and 36 expert opinion reviews on ADHD medication discontinuation, published from 1990 to 2013. Treatment persistence on stimulants, measured by treatment duration during the 12-month follow-up periods, averaged 136 days for children and adolescents and 230 days for adults. Owing to substantial study heterogeneity, comparisons across age or medication type subgroups were generally inconclusive; however, long-acting formulations and amphetamines were associated with longer treatment duration than short-acting formulations and methylphenidates. The medication possession ratio, used to measure adherence, was <0.7 for all age groups and medication classes during a 12-month period. Adverse effects were the most commonly cited reason for discontinuation in all studies. Original research studies reported the lack of symptom control as a common discontinuation reason, followed by dosing inconvenience, social stigma associated with ADHD medication, and the patient’s attitude. In summary, although there was a lack of consistency in the measurement of adherence and persistence, these findings indicate that drug adherence and persistence are generally poor among patients with ADHD. Clinicians may be able to help improve adherence and persistence to ADHD treatment by educating caregivers and patients on treatment goals, administering long-acting medications, and following-up with patients to verify if medication is still effective and well-tolerated. PMID:25187718

FEMALE SEX AND DISCONTINUATION OF ISONIAZID DUE TO ADVERSE EFFECTS DURING THE TREATMENT OF LATENT TUBERCULOSIS

PubMed Central

Pettit, April C.; Bethel, James; Hirsch-Moverman, Yael; Colson, Paul W.; Sterling, Timothy R.

2013-01-01

SUMMARY Objectives To determine the rate of and risk factors for discontinuation of isoniazid due to adverse effects during the treatment of latent tuberculosis infection in a large, multi-site study. Methods The Tuberculosis Epidemiologic Studies Consortium (TBESC) conducted a prospective study from March 2007–September 2008 among adults initiating isoniazid for treatment of LTBI at 12 sites in the US and Canada. The relative risk for isoniazid discontinuation due to adverse effects was determined using negative binomial regression. Adjusted models were constructed using forward stepwise regression. Results Of 1,306 persons initiating isoniazid, 617 (47.2%, 95% CI 44.5–50.0%) completed treatment and 196 (15.0%, 95% CI 13.1–17.1%) discontinued due to adverse effects. In multivariable analysis, female sex (RR 1.67, 95% CI 1.32–2.10, p<0.001) and current alcohol use (RR 1.41, 95% CI 1.13–1.77, p=0.003) were independently associated with isoniazid discontinuation due to adverse effects. Conclusions The rate of discontinuation of isoniazid due to adverse effects was substantially higher than reported earlier. Women were at increased risk of discontinuing isoniazid due to adverse effects; close monitoring of women for adverse effects may be warranted. Current alcohol use was also associated with isoniazid discontinuation; counseling patients to abstain from alcohol could decrease discontinuation due to adverse effects. PMID:23845828

Discontinuous Mode Power Supply

NASA Technical Reports Server (NTRS)

Lagadinos, John; Poulos, Ethel

2012-01-01

A document discusses the changes made to a standard push-pull inverter circuit to avoid saturation effects in the main inverter power supply. Typically, in a standard push-pull arrangement, the unsymmetrical primary excitation causes variations in the volt second integral of each half of the excitation cycle that could lead to the establishment of DC flux density in the magnetic core, which could eventually cause saturation of the main inverter transformer. The relocation of the filter reactor normally placed across the output of the power supply solves this problem. The filter reactor was placed in series with the primary circuit of the main inverter transformer, and is presented as impedance against the sudden changes on the input current. The reactor averaged the input current in the primary circuit, avoiding saturation of the main inverter transformer. Since the implementation of the described change, the above problem has not reoccurred, and failures in the main power transistors have been avoided.

Supersonic, subsonic and stationary filaments in the plasma focus

NASA Astrophysics Data System (ADS)

Nikulin, V. Ya; Startsev, S. A.; Tsybenko, S. P.

2017-10-01

Filaments in the plasma focus were investigated using a model of plasma with the London current. These structures involve a forward current that flows along the surface of a tangential discontinuity and reverse induction currents in the surrounding plasma, including those that flow over the surface of discontinuity, where the magnetic field reverses its direction. Supersonic filaments demonstrated the capture of plasma by the London current, and in subsonic and stationary filaments, the London current expelled the plasma.

Adverse mood effects of combined oral contraceptives in relation to personality traits.

PubMed

Borgström, Anna; Odlind, Viveca; Ekselius, Lisa; Sundström-Poromaa, Inger

2008-12-01

Mood symptoms, such as depressed mood, anxiety and increased irritability, remain one of the major reasons for discontinuation of combined oral contraceptive (COC) pills. The aim of this study was to compare personality traits in women with ongoing or previous use of COCs and different experiences from these compounds with respect to adverse mood symptoms. Thirty women currently on COCs with no reports of adverse mood symptoms, 28 women currently on COCs and experiencing mood-related side effects, 27 women who had discontinued COC use for reasons other than adverse mood symptoms and 33 women who had discontinued COC use due to adverse mood effects were included. All participants were asked to fill out the Swedish universities Scales of Personality (SSP) to assess different personality traits. The women who were experiencing mood-related side effects on their current COC use exhibited higher scores on the somatic anxiety and stress susceptibility traits as compared to the women who did not experience any mood-related side effects from their current COCs. Women who had discontinued COC treatment because of adverse mood effects had higher scores of detachment and mistrust compared to women who had discontinued COC for reasons unrelated to mood effects. Higher scores on specific personality traits such as somatic anxiety and stress susceptibility are found in women with ongoing experience of adverse mood symptoms from COC. Higher scores of mistrust and detachment are more common among women who have discontinued COC treatment due to adverse mood effects.

Learning from failure - rationale and design for a study about discontinuation of randomized trials (DISCO study)

PubMed Central

2012-01-01

Background Randomized controlled trials (RCTs) may be discontinued because of apparent harm, benefit, or futility. Other RCTs are discontinued early because of insufficient recruitment. Trial discontinuation has ethical implications, because participants consent on the premise of contributing to new medical knowledge, Research Ethics Committees (RECs) spend considerable effort reviewing study protocols, and limited resources for conducting research are wasted. Currently, little is known regarding the frequency and characteristics of discontinued RCTs. Methods/Design Our aims are, first, to determine the prevalence of RCT discontinuation for specific reasons; second, to determine whether the risk of RCT discontinuation for specific reasons differs between investigator- and industry-initiated RCTs; third, to identify risk factors for RCT discontinuation due to insufficient recruitment; fourth, to determine at what stage RCTs are discontinued; and fifth, to examine the publication history of discontinued RCTs. We are currently assembling a multicenter cohort of RCTs based on protocols approved between 2000 and 2002/3 by 6 RECs in Switzerland, Germany, and Canada. We are extracting data on RCT characteristics and planned recruitment for all included protocols. Completion and publication status is determined using information from correspondence between investigators and RECs, publications identified through literature searches, or by contacting the investigators. We will use multivariable regression models to identify risk factors for trial discontinuation due to insufficient recruitment. We aim to include over 1000 RCTs of which an anticipated 150 will have been discontinued due to insufficient recruitment. Discussion Our study will provide insights into the prevalence and characteristics of RCTs that were discontinued. Effective recruitment strategies and the anticipation of problems are key issues in the planning and evaluation of trials by investigators, Clinical Trial Units, RECs and funding agencies. Identification and modification of barriers to successful study completion at an early stage could help to reduce the risk of trial discontinuation, save limited resources, and enable RCTs to better meet their ethical requirements. PMID:22928744

SWRT: A package for semi-analytical solutions of surface wave propagation, including mode conversion, across transversely aligned vertical discontinuities

NASA Astrophysics Data System (ADS)

Datta, Arjun

2018-03-01

We present a suite of programs that implement decades-old algorithms for computation of seismic surface wave reflection and transmission coefficients at a welded contact between two laterally homogeneous quarter-spaces. For Love as well as Rayleigh waves, the algorithms are shown to be capable of modelling multiple mode conversions at a lateral discontinuity, which was not shown in the original publications or in the subsequent literature. Only normal incidence at a lateral boundary is considered so there is no Love-Rayleigh coupling, but incidence of any mode and coupling to any (other) mode can be handled. The code is written in Python and makes use of SciPy's Simpson's rule integrator and NumPy's linear algebra solver for its core functionality. Transmission-side results from this code are found to be in good agreement with those from finite-difference simulations. In today's research environment of extensive computing power, the coded algorithms are arguably redundant but SWRT can be used as a valuable testing tool for the ever evolving numerical solvers of seismic wave propagation. SWRT is available via GitHub (https://github.com/arjundatta23/SWRT.git).

Removal of the Gibbs phenomenon and its application to fast-Fourier-transform-based mode solvers.

PubMed

Wangüemert-Pérez, J G; Godoy-Rubio, R; Ortega-Moñux, A; Molina-Fernández, I

2007-12-01

A simple strategy for accurately recovering discontinuous functions from their Fourier series coefficients is presented. The aim of the proposed approach, named spectrum splitting (SS), is to remove the Gibbs phenomenon by making use of signal-filtering-based concepts and some properties of the Fourier series. While the technique can be used in a vast range of situations, it is particularly suitable for being incorporated into fast-Fourier-transform-based electromagnetic mode solvers (FFT-MSs), which are known to suffer from very poor convergence rates when applied to situations where the field distributions are highly discontinuous (e.g., silicon-on-insulator photonic wires). The resultant method, SS-FFT-MS, is exhaustively tested under the assumption of a simplified one-dimensional model, clearly showing a dramatic improvement of the convergence rates with respect to the original FFT-based methods.

Diffraction of entangled particles by light gratings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sancho, Pedro, E-mail: psanchos@aemet.es

We analyze the diffraction regime of the Kapitza–Dirac effect for particles entangled in momentum. The detection patterns show two-particle interferences. In the single-mode case we identify a discontinuity in the set of joint detection probabilities, associated with the disconnected character of the space of non-separable states. For Gaussian multi-mode states we derive the diffraction patterns, providing an example of the dependence of the light–matter interaction on entanglement. When the particles are identical, we can explore the relation between exchange and entanglement effects. We find a complementary behavior between overlapping and Schmidt’s number. In particular, symmetric entanglement can cancel the exchangemore » effects. - Highlights: • Kapitza–Dirac diffraction of entangled particles shows multiparticle interference. • There is a discontinuity in the set of joint detection patterns of entangled states. • We find a complementary behavior between overlapping and Schmidt’s number. • Symmetric entanglement can cancel the exchange effects.« less

Hyperthermia studies using inductive and ultrasound methods on E. coli bacteria and mouse glioma cells

NASA Astrophysics Data System (ADS)

Cabral-Prieto, A.; López-Callejas, R.; Rodríguez-Méndez, B. G.; Santos-Cuevas, C. L.; Celis-Almazán, J.; Olea-Mejía, O.; Gómez-Morales, J. L.; Peña-Eguiluz, R.; Valencia-Alvarado, R.; Mercado-Cabrera, A.; Muñoz-Castro, A. E.; García-Santibañez, F.

2017-11-01

The survival of Escherichia coli bacteria and mouse glioma cells were studied under different temperatures using direct heating in water, ultrasound, and magnetic fluid hyperthermia. The survival of these microorganisms depended on whether the heating mode was continuous or discontinuous, surviving more in the former than in the discontinuous heating mode. Whereas Escherichia coli bacteria did not survive at temperatures ≥50∘C, the mouse glioma cells did not survive at temperatures ≥48∘C. The survival of both these microorganisms was independent of the presence or absence of the magnetic nanoparticles of magnetite, suggesting that these, having mean particle sizes of 9.5, 8.5 and 5, did not show any apparent cytotoxicity effect. Present results also showed that the inductive heating system which used a radiofrequency of 13.56 MHz, providing a maximum magnetic field strength of 160 A/m, the electric rather than magnetic heating predominated.

Non-Evolutionarity of a Reconnecting Current Sheet as a Cause of Its Splitting into MHD Shocks

NASA Astrophysics Data System (ADS)

Markovsky, S. A.; Somov, B. V.

1995-04-01

Numerical simulations of the magnetic reconnection process in a current sheet show that, in some cases, MHD shocks appear to be attached to edges of the sheet. The appearance of the shocks may be considered to be a result of splitting of the sheet. In the present paper we suppose that this splitting takes place in consequence of non-evolutionarity of the reconnecting current sheet as a discontinuity. The problem of time evolution of small perturbations does not have a unique solution for a non-evolutionary discontinuity, and it splits into other (evolutionary) discontinuities. Such an approach allows us to determine conditions under which the splitting of the-sheet occurs. The main difficulty of this approach is that a current sheet is not reduced to a classified 1D discontinuity, because inhomogeneity of flow velocity inside the sheet is two-dimensional. To formulate the non-evolutionarity problem, we solve the linear MHD equations inside and outside the sheet and deduce linearized 1D boundary conditions at its surface. We show that for large enough conductivity, small perturbations exist which interact with the sheet as with a discontinuity. Then we obtain a non-evolutionarity criterion, with respect to these perturbations, in the form of a restriction on the flow velocity across the surface of the sheet.

Electromagnetic scattering from a class of open-ended waveguide discontinuities

NASA Technical Reports Server (NTRS)

Altintas, A.; Pathak, P. H.; Burnside, Walter D.

1986-01-01

A relatively simple high frequency analysis of electromagnetic scattering from a class of open-ended waveguide discontinuites was developed. The waveguides are composed of perfectly-conducting sections in which the electromagnetic field can be written as the sum of waveguide modes. Junctions are formed at the open end and also within interior regions where different sections are joined. The reflection and transmission properties of each junction are described in terms of a scattering matrix which is determined by combining the modal ray picture with high frequency techniques such as the Geometrical Theory of Diffraction (GTD), the Equivalent Current Method (ECM), and modifications of the Physical Theory of Diffraction (PTD). A new set of equivalent circuits are employed in this ECM analysis which leads to a simple treatment of many types of junction discontinuities. Also, a new procedure is presented to improve the efficiency of the aperture integration at the open end which is required in the PTD procedure for finding the fields radiated from (or coupled to) the open end. Once the scattering matrices are determined, they are then combined using a self-consistent multiple scattering method to obtain the total scattered fields.

A study of the high frequency limitations of series resonant converters

NASA Technical Reports Server (NTRS)

Stuart, T. A.; King, R. J.

1982-01-01

A transformer induced oscillation in series resonant (SR) converters is studied. It may occur in the discontinuous current mode. The source of the oscillation is an unexpected resonant circuit formed by normal resonance components in series with the magnetizing inductance of the output transformers. The methods for achieving cyclic stability are: to use a half bridge SR converter where q0.5. Q should be as close to 1.0 as possible. If 0.5q1.0, the instability will be avoided if psi2/3q-1/3. The second objective was to investigate a power field effect transistor (FET) version of the SR converter capable of operating at frequencies above 100 KHz, to study component stress and losses at various frequencies.

76 FR 41413 - Post Office Organization and Administration: Establishment, Classification, and Discontinuance

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-14

...) to improve the process for discontinuing Post Offices and other Postal Service-operated retail... appears below. The Postal Service is currently in the process of consultation under 39 U.S.C. 1004(b)-(d... or branches, the Postal Service is making that same process applicable to the discontinuance of all...

Kinetic effects on the currents determining the stability of a magnetic island in tokamaks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poli, E., E-mail: emanuele.poli@ipp.mpg.de; Bergmann, A.; Casson, F. J.

The role of the bootstrap and polarization currents for the stability of neoclassical tearing modes is investigated employing both a drift kinetic and a gyrokinetic approach. The adiabatic response of the ions around the island separatrix implies, for island widths below or around the ion thermal banana width, density flattening for islands rotating at the ion diamagnetic frequency, while for islands rotating at the electron diamagnetic frequency the density is unperturbed and the only contribution to the neoclassical drive arises from electron temperature flattening. As for the polarization current, the full inclusion of finite orbit width effects in the calculationmore » of the potential developing in a rotating island leads to a smoothing of the discontinuous derivatives exhibited by the analytic potential on which the polarization term used in the modeling is based. This leads to a reduction of the polarization-current contribution with respect to the analytic estimate, in line with other studies. Other contributions to the perpendicular ion current, related to the response of the particles around the island separatrix, are found to compete or even dominate the polarization-current term for realistic island rotation frequencies.« less

Strain energy release rates of composite interlaminar end-notch and mixed-mode fracture: A sublaminate/ply level analysis and a computer code

NASA Technical Reports Server (NTRS)

Valisetty, R. R.; Chamis, C. C.

1987-01-01

A computer code is presented for the sublaminate/ply level analysis of composite structures. This code is useful for obtaining stresses in regions affected by delaminations, transverse cracks, and discontinuities related to inherent fabrication anomalies, geometric configurations, and loading conditions. Particular attention is focussed on those layers or groups of layers (sublaminates) which are immediately affected by the inherent flaws. These layers are analyzed as homogeneous bodies in equilibrium and in isolation from the rest of the laminate. The theoretical model used to analyze the individual layers allows the relevant stresses and displacements near discontinuities to be represented in the form of pure exponential-decay-type functions which are selected to eliminate the exponential-precision-related difficulties in sublaminate/ply level analysis. Thus, sublaminate analysis can be conducted without any restriction on the maximum number of layers, delaminations, transverse cracks, or other types of discontinuities. In conjunction with the strain energy release rate (SERR) concept and composite micromechanics, this computational procedure is used to model select cases of end-notch and mixed-mode fracture specimens. The computed stresses are in good agreement with those from a three-dimensional finite element analysis. Also, SERRs compare well with limited available experimental data.

Dependence of displacement-length scaling relations for fractures and deformation bands on the volumetric changes across them

USGS Publications Warehouse

Schultz, R.A.; Soliva, R.; Fossen, H.; Okubo, C.H.; Reeves, D.M.

2008-01-01

Displacement-length data from faults, joints, veins, igneous dikes, shear deformation bands, and compaction bands define two groups. The first group, having a power-law scaling relation with a slope of n = 1 and therefore a linear dependence of maximum displacement and discontinuity length (Dmax = ??L), comprises faults and shear (non-compactional or non-dilational) deformation bands. These shearing-mode structures, having shearing strains that predominate over volumetric strains across them, grow under conditions of constant driving stress, with the magnitude of near-tip stress on the same order as the rock's yield strength in shear. The second group, having a power-law scaling relation with a slope of n = 0.5 and therefore a dependence of maximum displacement on the square root of discontinuity length (Dmax = ??L0.5), comprises joints, veins, igneous dikes, cataclastic deformation bands, and compaction bands. These opening- and closing-mode structures grow under conditions of constant fracture toughness, implying significant amplification of near-tip stress within a zone of small-scale yielding at the discontinuity tip. Volumetric changes accommodated by grain fragmentation, and thus control of propagation by the rock's fracture toughness, are associated with scaling of predominantly dilational and compactional structures with an exponent of n = 0.5. ?? 2008 Elsevier Ltd.

Effects of the Kelvin-Helmholtz surface instability on supersonic jets

NASA Technical Reports Server (NTRS)

Hardee, P. E.

1982-01-01

An exact numerical calculation is provided for of linear growth and phase velocity of Kelvin-Helmholtz unstable wave modes on a supersonic jet of cylindrical cross section. An expression for the maximally unstable wavenumber of each wave mode is found. Provided a sharp velocity discontinuity exists all wave modes are unstable. A combination of rapid jet expansion and velocity shear across a jet can effectively stabilize all wave modes. The more likely case of slow jet expansion and of velocity shear at the jet surface allows wave modes with maximally unstable wavelength longer than or on the order of the jet radius to grow. The relative energy in different wave modes and effect on the jet is investigated. Energy input into a jet resulting from surface instability is discussed.

Nondestructive evaluation of helicopter rotor blades using guided Lamb modes.

PubMed

Chakrapani, Sunil Kishore; Barnard, Daniel; Dayal, Vinay

2014-03-01

This paper presents an application for turning and direct modes in a complex composite laminate structure. The propagation and interaction of turning modes and fundamental Lamb modes are investigated in the skin, spar and web sections of a helicopter rotor blade. Finite element models were used to understand the various mode conversions at geometric discontinuities such as web-spar joints. Experimental investigation was carried out with the help of air coupled ultrasonic transducers. The turning and direct modes were confirmed with the help of particle displacements and velocities. Experimental B-Scans were performed on damaged and undamaged samples for qualitative and quantitative assessment of the structure. A strong correlation between the numerical and experimental results was observed and reported. Copyright © 2013 Elsevier B.V. All rights reserved.

A predication model for combustion modes of the scramjet-powered aerospace vehicle based on the nonlinear features of the isolator flow field

NASA Astrophysics Data System (ADS)

Yang, Qingchun; Wang, Hongxin; Chetehouna, Khaled; Gascoin, Nicolas

2017-01-01

The supersonic combustion ramjet (scramjet) engine remains the most promising airbreathing engine cycle for hypersonic flight, particularly the high-performance dual-mode scramjet in the range of flight Mach number from 4 to 7, because it can operates under different combustion modes. Isolator is a very key component of the dual-mode scramjet engine. In this paper, nonlinear characteristics of combustion mode transition is theoretically analyzed. The discontinuous sudden changes of static pressure and Mach number are obtained as the mode transition occurs, which emphasizing the importance of predication and control of combustion modes. In this paper, a predication model of different combustion modes is developed based on these these nonlinear features in the isolator flow field. it can provide a valuable reference for control system design of the scramjet-powered aerospace vehicle.

A thermodynamically consistent discontinuous Galerkin formulation for interface separation

DOE PAGES

Versino, Daniele; Mourad, Hashem M.; Dávila, Carlos G.; ...

2015-07-31

Our paper describes the formulation of an interface damage model, based on the discontinuous Galerkin (DG) method, for the simulation of failure and crack propagation in laminated structures. The DG formulation avoids common difficulties associated with cohesive elements. Specifically, it does not introduce any artificial interfacial compliance and, in explicit dynamic analysis, it leads to a stable time increment size which is unaffected by the presence of stiff massless interfaces. This proposed method is implemented in a finite element setting. Convergence and accuracy are demonstrated in Mode I and mixed-mode delamination in both static and dynamic analyses. Significantly, numerical resultsmore » obtained using the proposed interface model are found to be independent of the value of the penalty factor that characterizes the DG formulation. By contrast, numerical results obtained using a classical cohesive method are found to be dependent on the cohesive penalty stiffnesses. The proposed approach is shown to yield more accurate predictions pertaining to crack propagation under mixed-mode fracture because of the advantage. Furthermore, in explicit dynamic analysis, the stable time increment size calculated with the proposed method is found to be an order of magnitude larger than the maximum allowable value for classical cohesive elements.« less

Time-resolved measurement of global synchronization in the dust acoustic wave

NASA Astrophysics Data System (ADS)

Williams, J. D.

2014-10-01

A spatially and temporally resolved measurement of the synchronization of the naturally occurring dust acoustic wave to an external drive and the relaxation from the driven wave mode back to the naturally occuring wave mode is presented. This measurement provides a time-resolved measurement of the synchronization of the self-excited dust acoustic wave with an external drive and the return to the self-excited mode. It is observed that the wave synchronizes to the external drive in a distinct time-dependent fashion, while there is an immediate loss of synchronization when the external modulation is discontinued.

On the Stability of Strange Dwarf Hybrid Stars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alford, Mark G.; Harris, Steven P.; Sachdeva, Pratik S., E-mail: harrissp@wustl.edu

2017-10-01

We investigate the stability of “strange dwarfs”: white-dwarf-sized stars with a density discontinuity between a small dense core of quark matter and a thick low-density mantle of degenerate electrons. Previous work on strange dwarfs suggested that such a discontinuity could stabilize stars that would have been classified as unstable by the conventional criteria based on extrema in the mass–radius relation. We investigate the stability of such stars by numerically solving the Sturm–Liouville equations for the lowest-energy modes of the star. We find that the conventional criteria are correct, and strange dwarfs are not stable.

Observation of plasmon propagation, redirection, and fan-out in silver nanowires.

PubMed

Sanders, Aric W; Routenberg, David A; Wiley, Benjamin J; Xia, Younan; Dufresne, Eric R; Reed, Mark A

2006-08-01

We report the coupling of free-space photons (vacuum wavelength of 830 nm) to surface plasmon modes of a silver nanowire. The launch of propagating plasmons, and the subsequent emission of photons, is selective and occurs only at ends and other discontinuities of the nanowire. In addition, we observe that the nanowires redirect the plasmons through turns of radii as small as 4 microm. We exploit the radiating nature of discontinuities to find a plasmon propagation length >3 +/- 1 microm. Finally, we observe that interwire plasmon coupling occurs for overlapping wires, demonstrating plasmon fan-out at subwavelength scales.

On the surface-to-bulk mode conversion of Rayleigh waves.

NASA Technical Reports Server (NTRS)

Chang, C.-P.; Tuan, H.-S.

1973-01-01

Surface-to-bulk wave conversion phenomena occurring at a discontinuity characterized by a surface contour deformation are shown to be usable as a means for tapping Rayleigh waves in a nonpiezoelectric solid. A boundary perturbation technique is used in the treatment of the mode conversion problem. A systematic procedure is presented for calculating not only the first-order scattered waves, which include the reflected surface wave and the converted bulk wave, but also the higher order terms.

Stratigraphy -- The Fall of Continuity.

ERIC Educational Resources Information Center

Byers, Charles W.

1982-01-01

Reviews advances in stratigraphy as illustrated in the current geological literature, discussing discontinuity and how the recognition of discontinuity in the stratigraphic record is changing views of Superposition and Original Lateral Continuity. (Author/JN)

Global Hybrid Simulations of The Magnetopause Boundary Layers In Low- and High-latitude Magnetic Reconnections

NASA Astrophysics Data System (ADS)

Lin, Y.; Perez, J. D.

A 2-D global hybrid simulation is carried out to study the structure of the dayside mag- netopause in the noon-midnight meridian plane associated with magnetic reconnec- tion. In the simulation the bow shock, magnetosheath, and magnetopause are formed self-consistently by supersonic solar wind passing the geomagnetic field. The recon- nection events at high- and low-latitudes are simulated for various IMF conditions. The following results will be presented. (1) Large-amplitude rotational discontinuities and Alfvén waves are present in the quasi-steady reconnection layer. (2) The rotational discontinuity possesses an electron sense, or right-hand polarization in the magnetic field as the discontinuity forms from the X line. Later, however, the rotational dis- continuity tends to evolve to a structure with a smallest field rotational angle and thus may reverse its sense of the field rotation. The Walén relation is tested for elec- tron and ion flows in the magnetopause rotational discontinuities with left-hand and right-hand polarizations. (3) The structure of the magnetopause discontinuities and that of the accelerated/decelerated flows are modified significantly by the presence of the local magnetosheath flow. (4) Field-aligned currents are generated in the magne- topause rotational discontinuities. Part of the magnetopause currents propagate with Alfvén waves along the field lines into the polar ionosphere, contributing to the field- aligned current system in the high latitudes. The generation of the parallel currents under northward and southward IMF conditions is investigated. (5) Finally, typical ion velocity distributions will be shown at various locations across the magnetopause northward and southward of the X lines. The ion distributions associated with single or multiple X lines will be discussed.

Electronic and elastic mode locking in charge density wave conductors

NASA Astrophysics Data System (ADS)

Zettl, A.

1986-12-01

Mode locking phenomena are investigated in the charge density wave (CDW) materials NbSe 3 and TaS 3. The joint application of ac and dc electric fields results in free running and mode locked solutions for the CDW drift velocity, with associated ac-induced dynamic coherence lengths ξ D(ac) on the order of several hundred microns. The electronic response couples directly to the elastic properties of the crystal, with corresponding free running and mode locked solutions for the velocity of sound. Phase slip center-induced discontinuities in the CDW phase velocity lead to mode locked solutions with period doubling routes to chaos, and noisy precursor effects at bifurcation points. These results are discussed in terms of simple models of CDW domain synchronization, and internal CDW dynamics.

The role of density discontinuity in the inviscid instability of two-phase parallel flows

NASA Astrophysics Data System (ADS)

Behzad, M.; Ashgriz, N.

2014-02-01

We re-examine the inviscid instability of two-phase parallel flows with piecewise linear velocity profiles. Although such configuration has been theoretically investigated, we employ the concept of waves resonance to physically interpret the instability mechanism as well as the essential role of density discontinuity in the flow. Upon performing linear stability analysis, we demonstrate the existence of neutrally stable "density" and "density-vorticity" waves which are emerged due to the density jump in the flow, in addition to the well-known vorticity waves. Such waves are capable of resonating with each other to form unstable modes in the flow. Although unstable modes in this study are classified as the "shear instability" type, we demonstrate that they are not necessarily of the Rayleigh type. The results also show that the density can have both stabilizing and destabilizing effects on the flow stability. We verify that the difference in the resonating pair of neutral waves leads to such distinct behavior of the density variation.

A sophisticated simulation for the fracture behavior of concrete material using XFEM

NASA Astrophysics Data System (ADS)

Zhai, Changhai; Wang, Xiaomin; Kong, Jingchang; Li, Shuang; Xie, Lili

2017-10-01

The development of a powerful numerical model to simulate the fracture behavior of concrete material has long been one of the dominant research areas in earthquake engineering. A reliable model should be able to adequately represent the discontinuous characteristics of cracks and simulate various failure behaviors under complicated loading conditions. In this paper, a numerical formulation, which incorporates a sophisticated rigid-plastic interface constitutive model coupling cohesion softening, contact, friction and shear dilatation into the XFEM, is proposed to describe various crack behaviors of concrete material. An effective numerical integration scheme for accurately assembling the contribution to the weak form on both sides of the discontinuity is introduced. The effectiveness of the proposed method has been assessed by simulating several well-known experimental tests. It is concluded that the numerical method can successfully capture the crack paths and accurately predict the fracture behavior of concrete structures. The influence of mode-II parameters on the mixed-mode fracture behavior is further investigated to better determine these parameters.

Asymptotics of surface-plasmon redshift saturation at subnanometric separations

NASA Astrophysics Data System (ADS)

Schnitzer, Ory; Giannini, Vincenzo; Craster, Richard V.; Maier, Stefan A.

2016-01-01

Many promising nanophotonics endeavors hinge upon the unique plasmonic properties of nanometallic structures with narrow nonmetallic gaps, which support superconcentrated bonding modes that singularly redshift with decreasing separations. In this Rapid Communication, we present a descriptive physical picture, complemented by elementary asymptotic formulas, of a nonlocal mechanism for plasmon redshift saturation at subnanometric gap widths. Thus, by considering the electron-charge and field distributions in the close vicinity of the metal-vacuum interface, we show that nonlocality is asymptotically manifested as an effective potential discontinuity. For bonding modes in the near-contact limit, the latter discontinuity is shown to be effectively equivalent to a widening of the gap. As a consequence, the resonance-frequency near-contact asymptotics are a renormalization of the corresponding local ones. Specifically, the renormalization furnishes an asymptotic plasmon-frequency lower bound that scales with the 1 /4 power of the Fermi wavelength. We demonstrate these remarkable features in the prototypical cases of nanowire and nanosphere dimers, showing agreement between our elementary expressions and previously reported numerical computations.

Instability of Insulators near Quantum Phase Transitions

NASA Astrophysics Data System (ADS)

Doron, A.; Tamir, I.; Levinson, T.; Ovadia, M.; Sacépé, B.; Shahar, D.

2017-12-01

Thin films of amorphous indium oxide undergo a magnetic field driven superconducting to insulator quantum phase transition. In the insulating phase, the current-voltage characteristics show large current discontinuities due to overheating of electrons. We show that the onset voltage for the discontinuities vanishes as we approach the quantum critical point. As a result, the insulating phase becomes unstable with respect to any applied voltage making it, at least experimentally, immeasurable. We emphasize that unlike previous reports of the absence of linear response near quantum phase transitions, in our system, the departure from equilibrium is discontinuous. Because the conditions for these discontinuities are satisfied in most insulators at low temperatures, and due to the decay of all characteristic energy scales near quantum phase transitions, we believe that this instability is general and should occur in various systems while approaching their quantum critical point. Accounting for this instability is crucial for determining the critical behavior of systems near the transition.

Dispersion Energy Analysis of Rayleigh and Love Waves in the Presence of Low-Velocity Layers in Near-Surface Seismic Surveys

NASA Astrophysics Data System (ADS)

Mi, Binbin; Xia, Jianghai; Shen, Chao; Wang, Limin

2018-03-01

High-frequency surface-wave analysis methods have been effectively and widely used to determine near-surface shear (S) wave velocity. To image the dispersion energy and identify different dispersive modes of surface waves accurately is one of key steps of using surface-wave methods. We analyzed the dispersion energy characteristics of Rayleigh and Love waves in near-surface layered models based on numerical simulations. It has been found that if there is a low-velocity layer (LVL) in the half-space, the dispersion energy of Rayleigh or Love waves is discontinuous and ``jumping'' appears from the fundamental mode to higher modes on dispersive images. We introduce the guided waves generated in an LVL (LVL-guided waves, a trapped wave mode) to clarify the complexity of the dispersion energy. We confirm the LVL-guided waves by analyzing the snapshots of SH and P-SV wavefield and comparing the dispersive energy with theoretical values of phase velocities. Results demonstrate that LVL-guided waves possess energy on dispersive images, which can interfere with the normal dispersion energy of Rayleigh or Love waves. Each mode of LVL-guided waves having lack of energy at the free surface in some high frequency range causes the discontinuity of dispersive energy on dispersive images, which is because shorter wavelengths (generally with lower phase velocities and higher frequencies) of LVL-guided waves cannot penetrate to the free surface. If the S wave velocity of the LVL is higher than that of the surface layer, the energy of LVL-guided waves only contaminates higher mode energy of surface waves and there is no interlacement with the fundamental mode of surface waves, while if the S wave velocity of the LVL is lower than that of the surface layer, the energy of LVL-guided waves may interlace with the fundamental mode of surface waves. Both of the interlacements with the fundamental mode or higher mode energy may cause misidentification for the dispersion curves of surface waves.

Safety Evaluation of Discontinuing Late-Night Flash Operations at Signalized Intersections : Summary Report

DOT National Transportation Integrated Search

2013-08-01

During late-night flash (LNF) mode (from late night to early morning hours), traffic signals flash yellow for one road (typically, the major road), requiring caution but no stopping, and flash red for the other road (typically, the minor road), requi...

The Origin of Compressible Magnetic Turbulence in the Very Local Interstellar Medium

NASA Astrophysics Data System (ADS)

Zank, G. P.; Du, S.; Hunana, P.

2017-06-01

Voyager 1 observed compressible magnetic turbulence in the very local interstellar medium (VLISM). We show that inner heliosheath (IHS) fast- and slow-mode waves incident on the heliopause (HP) generate VLISM fast-mode waves only that propagate into the VLISM. We suggest that this is the origin of compressible turbulence in the VLISM. We show that fast- and slow-mode waves transmitted across a tangential discontinuity such as the HP are strongly refracted on crossing the HP and subsequently propagate at highly oblique angles to the VLISM magnetic field. Thus, fast-mode waves in the VLISM contribute primarily to the compressible and not the transverse components of the VLISM fluctuating magnetic field variance < δ {\\hat{B}}2> since < δ {\\hat{B}}{fz}2> \

Inspection of helicopter rotor blades with the help of guided waves and "turning modes": Experimental and finite element analysis

NASA Astrophysics Data System (ADS)

Barnard, Daniel; Chakrapani, Sunil Kishore; Dayal, Vinay

2013-01-01

Modern helicopter rotor blades constructed of composite materials offer significant inspection challenges, particularly at inner structures, where geometry and differing material properties and anisotropy make placement of the probing energy difficult. This paper presents an application of Lamb waves to these structures, where mode conversion occurs at internal geometric discontinuities. These additional modes were found to successfully propagate to the targeted regions inside the rotor and back out, allowing evaluation of the structure. A finite element model was developed to simulate wave propagation and mode conversion in the structure and aid in identifying the signals received in the laboratory experiment. A good correlation between numerical and experimental results was observed.

A new optimal sliding mode controller design using scalar sign function.

PubMed

Singla, Mithun; Shieh, Leang-San; Song, Gangbing; Xie, Linbo; Zhang, Yongpeng

2014-03-01

This paper presents a new optimal sliding mode controller using the scalar sign function method. A smooth, continuous-time scalar sign function is used to replace the discontinuous switching function in the design of a sliding mode controller. The proposed sliding mode controller is designed using an optimal Linear Quadratic Regulator (LQR) approach. The sliding surface of the system is designed using stable eigenvectors and the scalar sign function. Controller simulations are compared with another existing optimal sliding mode controller. To test the effectiveness of the proposed controller, the controller is implemented on an aluminum beam with piezoceramic sensor and actuator for vibration control. This paper includes the control design and stability analysis of the new optimal sliding mode controller, followed by simulation and experimental results. The simulation and experimental results show that the proposed approach is very effective. © 2013 ISA. Published by Elsevier Ltd. All rights reserved.

Fuzzy fractional order sliding mode controller for nonlinear systems

NASA Astrophysics Data System (ADS)

Delavari, H.; Ghaderi, R.; Ranjbar, A.; Momani, S.

2010-04-01

In this paper, an intelligent robust fractional surface sliding mode control for a nonlinear system is studied. At first a sliding PD surface is designed and then, a fractional form of these networks PDα, is proposed. Fast reaching velocity into the switching hyperplane in the hitting phase and little chattering phenomena in the sliding phase is desired. To reduce the chattering phenomenon in sliding mode control (SMC), a fuzzy logic controller is used to replace the discontinuity in the signum function at the reaching phase in the sliding mode control. For the problem of determining and optimizing the parameters of fuzzy sliding mode controller (FSMC), genetic algorithm (GA) is used. Finally, the performance and the significance of the controlled system two case studies (robot manipulator and coupled tanks) are investigated under variation in system parameters and also in presence of an external disturbance. The simulation results signify performance of genetic-based fuzzy fractional sliding mode controller.

Relaxation models for single helical reversed field pinch plasmas

NASA Astrophysics Data System (ADS)

Paccagnella, Roberto

2016-09-01

In this paper, a relaxation theory for plasmas where a single dominant mode is present [Bhattacharjee et al., Phys. Rev. Lett. 45, 347 (1980)], is revisited. The solutions of a related eigenvalue problem are numerically calculated and discussed. Although these solutions can reproduce well, the magnetic fields measured in experiments, there is no way within the theory to determine the dominant mode, whose pitch is a free parameter in the model. To find the preferred helical perturbation, a procedure is proposed that minimizes the "distance" of the relaxed state from a state which is constructed as a two region generalization of the Taylor's relaxation model [Taylor, Phys. Rev. Lett. 33, 1139 (1974); Rev. Mod. Phys. 58, 751 (1986)] and that allows current discontinuities. It is found that this comparison is able to predict the observed scaling with the aspect ratio and reversal parameter for the dominant mode in the Single Helical states. The aspect ratio scaling alone is discussed in a previous paper [Paccagnella, Nucl. Fusion 56, 046010 (2016)] in terms of the efficient response of a toroidal shell to specific modes (leaving a sign undetermined), showing that the ideal wall boundary condition, a key ingredient in relaxation theories, is particularly well matched for them. Therefore, the present paper altogether [Paccagnella, Nucl. Fusion 56, 046010 (2016)] can give a new and satisfactory explanation of some robust and reproducible experimental facts observed in the Single Helical Reversed Field Pinch plasmas and never explained before.

Seismic imaging of a mid-lithospheric discontinuity beneath Ontong Java Plateau

NASA Astrophysics Data System (ADS)

Tharimena, Saikiran; Rychert, Catherine A.; Harmon, Nicholas

2016-09-01

Ontong Java Plateau (OJP) is a huge, completely submerged volcanic edifice that is hypothesized to have formed during large plume melting events ∼90 and 120 My ago. It is currently resisting subduction into the North Solomon trench. The size and buoyancy of the plateau along with its history of plume melting and current interaction with a subduction zone are all similar to the characteristics and hypothesized mechanisms of continent formation. However, the plateau is remote, and enigmatic, and its proto-continent potential is debated. We use SS precursors to image seismic discontinuity structure beneath Ontong Java Plateau. We image a velocity increase with depth at 28 ± 4 km consistent with the Moho. In addition, we image velocity decreases at 80 ± 5 km and 282 ± 7 km depth. Discontinuities at 60-100 km depth are frequently observed both beneath the oceans and the continents. However, the discontinuity at 282 km is anomalous in comparison to surrounding oceanic regions; in the context of previous results it may suggest a thick viscous root beneath OJP. If such a root exists, then the discontinuity at 80 km bears some similarity to the mid-lithospheric discontinuities (MLDs) observed beneath continents. One possibility is that plume melting events, similar to that which formed OJP, may cause discontinuities in the MLD depth range. Plume-plate interaction could be a mechanism for MLD formation in some continents in the Archean prior to the onset of subduction.

On the resonance hypothesis of storm surge and surf beat run-up

NASA Astrophysics Data System (ADS)

Postacioglu, Nazmi; Sinan Özeren, M.; Canlı, Umut

2017-06-01

Resonance has recently been proposed as the fundamental underlying mechanism that shapes the amplification in coastal run-up for storm surges and surf beats, which are long-wavelength disturbances created by fluid velocity differences between the wave groups and the regions outside the wave groups. It is without doubt that the resonance plays a role in run-up phenomena of various kinds; however, we think that the extent to which it plays its role has not been completely understood. For incident waves, which we assume to be linear, the best approach to investigate the role played by the resonance would be to calculate the normal modes by taking radiation damping into account and then testing how those modes are excited by the incident waves. Such modes diverge offshore, but they can still be used to calculate the run-up. There are a small number of previous works that attempt to calculate the resonant frequencies, but they do not relate the amplitudes of the normal modes to those of the incident wave. This is because, by not including radiation damping, they automatically induce a resonance that leads to infinite amplitudes, thus preventing them from predicting the exact contribution of the resonance to coastal run-up. In this study we consider two different coastal geometries: an infinitely wide beach with a constant slope connecting to a flat-bottomed deep ocean and a bay with sloping bottom, again, connected to a deep ocean. For the fully 1-D problem we find significant resonance if the bathymetric discontinuity is large.The linearisation of the seaward boundary condition leads to slightly smaller run-ups. For the 2-D ocean case the analysis shows that the wave confinement is very effective when the bay is narrow. The bay aspect ratio is the determining factor for the radiation damping. One reason why we include a bathymetric discontinuity is to mimic some natural settings where bays and gulfs may lead to abrupt depth gradients such as the Tokyo Bay. The other reason is, as mentioned above, to test the role played by the depth discontinuity for resonance.

Predictors of statin adherence, switching, and discontinuation in the USAGE survey: understanding the use of statins in America and gaps in patient education.

PubMed

Wei, Melissa Y; Ito, Matthew K; Cohen, Jerome D; Brinton, Eliot A; Jacobson, Terry A

2013-01-01

Although statins have been shown to reduce cardiovascular disease mortality, less than half of U.S. adults achieve their low-density lipoprotein cholesterol goal. In many patients initiated on a statin, adherence rates decrease over time. To characterize current and former statin users, identify reasons for the discontinuation or switching of statins, and identify factors associated with adherence. The USAGE survey is a cross-sectional, self-administered Internet-based survey of 10,138 U.S. adults fielded September to October 2011. The following statin users were identified and compared: adherent nonswitchers, adherent switchers, non-adherent switchers, and discontinuers. Univariate and multivariate models using a priori covariates for adherence and discontinuation were examined. Most participants were current statin users who adhered with their prescribed statin (82.5%, n = 8371). Former statin users or discontinuers (12%, n = 1220) cited muscle pain, a side effect, as the primary reason for discontinuation (60%), followed by cost (16%), and then perceived lack of efficacy (13%). Discontinuers were less satisfied with their physicians' explanation of cholesterol treatment, more likely to use the Internet to research statins, and less likely to undergo frequent cholesterol monitoring. Among adherent statin users, the primary reasons for switching were muscle side effects (33%) and cost (32%). Individuals at risk for non-adherence included those with low household income, those who experienced muscle pain as a side effect while on statin therapy, and those taking medication for cardiovascular disease. Statin-related muscle side effects are common and contribute significantly to rates of discontinuation, switching, and non-adherence. Improved physician patient communication about side effects and benefits of statins are necessary to improve both adherence and outcomes. Copyright © 2013 National Lipid Association. Published by Elsevier Inc. All rights reserved.

Variability modes of precipitation along a Central Mediterranean area and their relations with ENSO, NAO, and other climatic patterns

NASA Astrophysics Data System (ADS)

Kalimeris, Anastasios; Ranieri, Ezio; Founda, Dimitra; Norrant, Caroline

2017-12-01

This study analyses a century-long set of precipitation time series in the Central Mediterranean (encompassing the Greek Ionian and the Italian Puglia regions) and investigates the statistically significant modes of the interannual precipitation variability using efficient methods of spectral decomposition. The statistical relations and the possible physical couplings between the detected modes and the global or hemispheric patterns of climatic variability (the El Niño Southern Oscillation or ENSO, the North Atlantic Oscillation or NAO, the East Atlantic or EA, the Scandinavian or SCAND, and others) were examined in the time-frequency domain and low-order synchronization events were sought. Significant modes of precipitation variability were detected in the Taranto Gulf and the southern part of the Greek Ionian region at the sub-decadal scales (mostly driven by the SCAND pattern) and particularly at the decadal and quasi-decadal scales, where strong relations found with the ENSO activity (under complex implications of EA and NAO) prior to the 1930s or after the early-1970s. The precipitation variations in the Adriatic stations of Puglia are dominated by significant bi-decadal modes which found to be coherent with the ENSO activity and also weakly related with the Atlantic Ocean sea surface temperature intrinsic variability. Additionally, important discontinuities characterize the evolution of precipitation in certain stations of the Taranto Gulf and the Greek Ionian region during the early-1960s and particularly during the early-1970s, followed by significant reductions in the mean annual precipitation. These discontinuities seem to be associated with regional effects of NAO and SCAND, probably combined with the impact of the 1970s climatic shift in the Pacific and the ENSO variability.

Caffeine and exercise.

PubMed

Paluska, Scott A

2003-08-01

Caffeine is the most commonly consumed drug in the world, and athletes frequently use it as an ergogenic aid. It improves performance and endurance during prolonged, exhaustive exercise. To a lesser degree it also enhances short-term, high-intensity athletic performance. Caffeine improves concentration, reduces fatigue, and enhances alertness. Habitual intake does not diminish caffeine's ergogenic properties. Several mechanisms have been proposed to explain the physiologic effects of caffeine, but adenosine receptor antagonism most likely accounts for the primary mode of action. It is relatively safe and has no known negative performance effects, nor does it cause significant dehydration or electrolyte imbalance during exercise. Routine caffeine consumption may cause tolerance or dependence, and abrupt discontinuation produces irritability, mood shifts, headache, drowsiness, or fatigue. Major sport governing bodies ban excessive use of caffeine, but current monitoring techniques are inadequate, and ethical dilemmas persist regarding caffeine intake by athletes.

Chattering-Free Sliding Mode Control with Unmodeled Dynamics

NASA Technical Reports Server (NTRS)

Krupp, Don; Shtessel, Yuri B.

1999-01-01

Sliding mode control systems are valued for their robust accommodation of uncertainties and their ability to reject disturbances. In this paper, a design methodology is proposed to eliminate the chattering phenomenon affecting sliding mode controlled plants with input unmodeled actuator dynamics of second order or greater. The proposed controller design is based on the relative degrees of the plant and the unmodeled actuator dynamics and the ranges of the uncertainties of the plant and actuator. The controller utilizes the pass filter characteristics of the physical actuating device to provide a smoothing effect on the discontinuous control signal rather than introducing any artificial dynamics into the controller design thus eliminating chattering in the system's output response.

Monolithic microwave integrated circuit devices for active array antennas

NASA Technical Reports Server (NTRS)

Mittra, R.

1984-01-01

Two different aspects of active antenna array design were investigated. The transition between monolithic microwave integrated circuits and rectangular waveguides was studied along with crosstalk in multiconductor transmission lines. The boundary value problem associated with a discontinuity in a microstrip line is formulated. This entailed, as a first step, the derivation of the propagating as well as evanescent modes of a microstrip line. The solution is derived to a simple discontinuity problem: change in width of the center strip. As for the multiconductor transmission line problem. A computer algorithm was developed for computing the crosstalk noise from the signal to the sense lines. The computation is based on the assumption that these lines are terminated in passive loads.

Do joints initiate as sharp mode I fractures or finite thickness dilatancy bands? Insights from laboratory experiments and field data

NASA Astrophysics Data System (ADS)

Petit, J.; Chemenda, A. I.; Jorand, C.

2011-12-01

Terminology on fracture and discontinuities in geological objects mainly relies on distinguishing between tabular and sharp forms of deformation localization/failure structures (Aydin et al, JSG 2006; Shultz and Fossen, AAPG, 2009). On this basis joints (considered as mode I fractures) and dilation bands (very rarely observed) are distinguished among extension discontinuities. The former propagate with the separation of the fracture walls due to strong stress concentration at the fracture tips. The plumose features or hackles typical of joints (these terms cover a wide variety of diverging fractographic features) are believed to result from the fracture front breakdown due to the loading mode change (the origin of this change remains unclear). This view is called into question by recent experimental results of extension tests conducted on a synthetic physical rock analogue (granular, frictional, cohesive and dilatant) material (GRAM1) and by field observations of embryonic (not yet open) joints in highly jointed dolomicrite Chemenda et al., JGR, 2011). The initial porosity and grain size of both materials are very different, but at SEM scale, both experimental and natural unopened discontinuities reveal a comparable dilatancy (dilation) band structure with a porosity increase over a width of several grains. This suggests that the distinction between tabular and sharp is a matter of observation scale. Both axisymetric and poly-axial extension tests show that dilatancy bands form at elevated mean stress and have plumose morphology. Mode I cracking occurs only at very low mean stres and the forming fractures do not bear plumose features. Thus the absence of plumose structures can be considered as the signature of mode I fracturing. Consequently, we propose that non- plumose bearing natural joints (provided their fractography is not eroded) could originate as mode I fractures and call them "mode I joints". We call the joints formed as closed dilatancy bands propagating at relatively high pressure (depth) conditions and generating the plumose fractography "dilatancy joints". These joints obtained in poly-axial experiments can be very tight as is also often observed in nature. Joint spacing was shown to depend on the loading conditions but not on the sample thickness, which is another argument against the mode I mechanism. There are two main reasons for which the dilatancy joints were not detected previously: (1) the dilatancy band tends to open during exhumation (it is a weakness zone) leading to the separation of the two walls with destruction of the dilatancy band texture and mineral infilling; (2) if no opening occurs, as soon as the band of increased permeability is formed, diagenetic/epigenetic processes can rapidly cancel the initial structure, the trace of the band appearing at great magnification as a tiny mineralized vein. Such transformation must be very frequent in sedimentary rocks, but it can be absent when the mineral solubility is limited, as for the dolomicrite example presented.

Uncertainty Quantification given Discontinuous Climate Model Response and a Limited Number of Model Runs

NASA Astrophysics Data System (ADS)

Sargsyan, K.; Safta, C.; Debusschere, B.; Najm, H.

2010-12-01

Uncertainty quantification in complex climate models is challenged by the sparsity of available climate model predictions due to the high computational cost of model runs. Another feature that prevents classical uncertainty analysis from being readily applicable is bifurcative behavior in climate model response with respect to certain input parameters. A typical example is the Atlantic Meridional Overturning Circulation. The predicted maximum overturning stream function exhibits discontinuity across a curve in the space of two uncertain parameters, namely climate sensitivity and CO2 forcing. We outline a methodology for uncertainty quantification given discontinuous model response and a limited number of model runs. Our approach is two-fold. First we detect the discontinuity with Bayesian inference, thus obtaining a probabilistic representation of the discontinuity curve shape and location for arbitrarily distributed input parameter values. Then, we construct spectral representations of uncertainty, using Polynomial Chaos (PC) expansions on either side of the discontinuity curve, leading to an averaged-PC representation of the forward model that allows efficient uncertainty quantification. The approach is enabled by a Rosenblatt transformation that maps each side of the discontinuity to regular domains where desirable orthogonality properties for the spectral bases hold. We obtain PC modes by either orthogonal projection or Bayesian inference, and argue for a hybrid approach that targets a balance between the accuracy provided by the orthogonal projection and the flexibility provided by the Bayesian inference - where the latter allows obtaining reasonable expansions without extra forward model runs. The model output, and its associated uncertainty at specific design points, are then computed by taking an ensemble average over PC expansions corresponding to possible realizations of the discontinuity curve. The methodology is tested on synthetic examples of discontinuous model data with adjustable sharpness and structure. This work was supported by the Sandia National Laboratories Seniors’ Council LDRD (Laboratory Directed Research and Development) program. Sandia National Laboratories is a multi-program laboratory operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-AC04-94AL85000.

Antipsychotic discontinuation syndromes: a narrative review of the evidence and its integration into Australian mental health nursing textbooks.

PubMed

Salomon, Carmela; Hamilton, Bridget

2014-02-01

In light of the high number of people discontinuing antipsychotics each year, it is essential that nurses develop a robust understanding of all aspects of the discontinuation experience. While there is a large body of published work documenting post-discontinuation relapse rates, less is known about other aspects of the discontinuation experience. This paper presents the results of a narrative review of international studies of antipsychotic discontinuation syndromes and their relevance to nursing practice. Four key mental health nursing textbooks used in student nurse education in Australia are examined to assess how this evidence has been incorporated into clinical recommendations. This review finds that the evidence for discontinuation syndromes could be more widely disseminated and applied than it is at present. Strikingly, this evidence has not been incorporated into key mental health nursing textbooks in Australia at all. Slow integration into nursing published work may be influenced by a number of clinical and research uncertainties. We consider the impact of this silence on key nursing roles of psycho-education and adverse event monitoring during antipsychotic discontinuation periods. Further robust research should be conducted into discontinuation syndromes as a matter of urgency. Given the high number of consumers potentially impacted upon by discontinuation syndromes, nurse authors and educators should consider revising key nursing textbooks to include the currently available information about discontinuation syndromes. © 2012 The Authors; International Journal of Mental Health Nursing © 2012 Australian College of Mental Health Nurses Inc.

Contraceptive discontinuation and switching among Ghanaian women: evidence from the Ghana Demographic and Health Survey, 2008.

PubMed

Modey, Emefa J; Aryeetey, Richmond; Adanu, Richard

2014-03-01

This study identifies factors associated with contraceptive discontinuation and switching among Ghanaian women of reproductive age, using data from 1,378 female respondents of the 2008 Ghana Demographic and Health Survey. Logistic regression models were used to determine relationships between key socio-demographic factors and user status. Discontinued use occurred among 56% of ever users and switching among 55% of current users. The IUD was most abandoned (70%) and its use was associated with almost twice the odds of discontinuation (OR = 1.97; 95% CI (1.04, 3.75)). Having a history of terminated pregnancy significantly predicted both discontinuation (OR = 1.36; 95% CI (1.03, 1.79) and switching (OR = 1.78; 95% CI (1.16, 2.73)) and intention to limit births significantly predicted lower discontinuation (OR = 0.71; 95% CI (0.52, 0.96)). Counseling services emphasizing contraceptive options and reinforcing switching are critically needed to reduce unwanted pregnancies that may result from poor method use and discontinuation especially among post-abortion clients and IUD users.

Discontinuation of Buprenorphine Maintenance Therapy: Perspectives and Outcomes

PubMed Central

Bentzley, Brandon S.; Barth, Kelly S.; Back, Sudie E.; Book, Sarah W.

2015-01-01

Buprenorphine maintenance therapy (BMT) is increasingly the preferred opioid maintenance agent due to its reduced toxicity and availability in an office-based setting in the United States. Although BMT has been shown to be highly efficacious, it is often discontinued soon after initiation. No current systematic review has yet investigated providers’ or patients’ reasons for BMT discontinuation or the outcomes that follow. Hence, provider and patient perspectives associated with BMT discontinuation after a period of stable buprenorphine maintenance and the resultant outcomes were systematically reviewed with specific emphasis on pre-buprenorphine-taper parameters predictive of relapse following BMT discontinuation. Few identified studies address provider or patient perspectives associated with buprenorphine discontinuation. Within the studies reviewed providers with residency training in BMT were more likely to favor long term BMT instead of detoxification, and providers were likely to consider BMT discontinuation in the face of medication misuse. Patients often desired to remain on BMT because of fear of relapse to illicit opioid use if they were to discontinue BMT. The majority of patients who discontinued BMT did so involuntarily, often due to failure to follow strict program requirements, and 1 month following discontinuation, rates of relapse to illicit opioid use exceeded 50% in every study reviewed. Only lower buprenorphine maintenance dose, which may be a marker for attenuated addiction severity, predicted better outcomes across studies. Relaxed BMT program requirements and frequent counsel on the high probability of relapse if BMT is discontinued may improve retention in treatment and prevent the relapse to illicit opioid use that is likely to follow BMT discontinuation. PMID:25601365

Velocity mode transition of dynamic crack propagation in hyperviscoelastic materials: A continuum model study

PubMed Central

Kubo, Atsushi; Umeno, Yoshitaka

2017-01-01

Experiments of crack propagation in rubbers have shown that a discontinuous jump of crack propagation velocity can occur as energy release rate increases, which is known as the “mode transition” phenomenon. Although it is believed that the mode transition is strongly related to the mechanical properties, the nature of the mode transition had not been revealed. In this study, dynamic crack propagation on an elastomer was investigated using the finite element method (FEM) with a hyperviscoelastic material model. A series of pure shear test was carried out numerically with FEM simulations and crack velocities were measured under various values of tensile strain. As a result, our FEM simulations successfully reproduced the mode transition. The success of realising the mode transition phenomenon by a simple FEM model, which was achieved for the first time ever, helped to explain that the phenomenon occurs owing to a characteristic non-monotonic temporal development of principal stress near the crack tip. PMID:28186205

Velocity mode transition of dynamic crack propagation in hyperviscoelastic materials: A continuum model study

NASA Astrophysics Data System (ADS)

Kubo, Atsushi; Umeno, Yoshitaka

2017-02-01

Experiments of crack propagation in rubbers have shown that a discontinuous jump of crack propagation velocity can occur as energy release rate increases, which is known as the “mode transition” phenomenon. Although it is believed that the mode transition is strongly related to the mechanical properties, the nature of the mode transition had not been revealed. In this study, dynamic crack propagation on an elastomer was investigated using the finite element method (FEM) with a hyperviscoelastic material model. A series of pure shear test was carried out numerically with FEM simulations and crack velocities were measured under various values of tensile strain. As a result, our FEM simulations successfully reproduced the mode transition. The success of realising the mode transition phenomenon by a simple FEM model, which was achieved for the first time ever, helped to explain that the phenomenon occurs owing to a characteristic non-monotonic temporal development of principal stress near the crack tip.

Velocity mode transition of dynamic crack propagation in hyperviscoelastic materials: A continuum model study.

PubMed

Kubo, Atsushi; Umeno, Yoshitaka

2017-02-10

Experiments of crack propagation in rubbers have shown that a discontinuous jump of crack propagation velocity can occur as energy release rate increases, which is known as the "mode transition" phenomenon. Although it is believed that the mode transition is strongly related to the mechanical properties, the nature of the mode transition had not been revealed. In this study, dynamic crack propagation on an elastomer was investigated using the finite element method (FEM) with a hyperviscoelastic material model. A series of pure shear test was carried out numerically with FEM simulations and crack velocities were measured under various values of tensile strain. As a result, our FEM simulations successfully reproduced the mode transition. The success of realising the mode transition phenomenon by a simple FEM model, which was achieved for the first time ever, helped to explain that the phenomenon occurs owing to a characteristic non-monotonic temporal development of principal stress near the crack tip.

Gravitational Radiation with a Positive Cosmological Constant

NASA Astrophysics Data System (ADS)

Bonga, Beatrice

Gravitational radiation is well-understood in spacetimes that are asymptotically flat. However, our Universe is currently expanding at an accelerated rate, which is best described by including a positive cosmological constant, Lambda, in Einstein's equations. Consequently, no matter how far one recedes from sources generating gravitational waves, spacetime curvature never dies and is not asymptotically flat. This dissertation provides first steps to incorporate Lambda in the study of gravitational radiation by analyzing linearized gravitational waves on a de Sitter background. Since the asymptotic structure of de Sitter is very different from that of Minkowski spacetime, many conceptual and technical difficulties arise. The limit Lambda → 0 can be discontinuous: Although energy carried by gravitational waves is always positive in Minkowski spacetime, it can be arbitrarily negative in de Sitter spacetime. Additionally, many of the standard techniques, including 1/r expansions, are no longer applicable. We generalize Einstein's celebrated quadrupole formula describing the power radiated on a flat background to de Sitter spacetime. Even a tiny Lambda brings in qualitatively new features such as contributions from pressure quadrupole moments. Nonetheless, corrections induced by Lambda are O(√Lambda tc) with tc the characteristic time scale of the source and are negligible for current gravitational wave observatories. We demonstrate this explicitly for a binary system in a circular orbit. Radiative modes are encoded in the transverse-traceless part of the spatial components of a gravitational perturbation. When Lambda = 0, one typically extracts these modes in the wave zone by projecting the gravitational perturbation onto the two-sphere orthogonal to the radial direction. We show that this method for waves emitted by spatially compact sources on Minkowski spacetime generically does not yield the transverse-traceless modes; not even infinitely far away. However, the difference between the transverse-traceless and projected modes is non-dynamical and disappears from all physical observables. When one is interested in 'Coulombic' information not captured by the radiative modes, the projection method does not suffice. This is, for example, important for angular momentum carried by gravitational waves. This result relies on Bondi-type expansions for asymptotically flat spacetimes. Therefore, the projection method is not applicable to de Sitter spacetimes.

Exact Large-Deviation Statistics for a Nonequilibrium Quantum Spin Chain

NASA Astrophysics Data System (ADS)

Žnidarič, Marko

2014-01-01

We consider a one-dimensional XX spin chain in a nonequilibrium setting with a Lindblad-type boundary driving. By calculating large-deviation rate function in the thermodynamic limit, a generalization of free energy to a nonequilibrium setting, we obtain a complete distribution of current, including closed expressions for lower-order cumulants. We also identify two phase-transition-like behaviors in either the thermodynamic limit, at which the current probability distribution becomes discontinuous, or at maximal driving, when the range of possible current values changes discontinuously. In the thermodynamic limit the current has a finite upper and lower bound. We also explicitly confirm nonequilibrium fluctuation relation and show that the current distribution is the same under mapping of the coupling strength Γ→1/Γ.

Effectively Single-Mode Self-Recovering Ultrafast Nonlinear Nanowire Surface Plasmons

NASA Astrophysics Data System (ADS)

Tuniz, Alessandro; Weidlich, Stefan; Schmidt, Markus A.

2018-04-01

We report on a regime for surface-plasmon propagation, which is robust to defects and effectively single mode, and we exploit it for accessing the ultrafast nonlinear response of gold on centimeter-long subwavelength-diameter cylindrical nanowires. The hybrid plasmonic-photonic platform is formed by a gold nanowire, monolithically integrated into the core of an optical fiber. We show that, despite the dual-waveguide nature of this structure, the long-range surface plasmon is the only effectively propagating mode in the near infrared, which self-recovers in the presence of gaps via a light-recapturing effect. This self-recovery overcomes detrimental effects of wire discontinuities and enables measurements of the ultrafast nonlinearity of gold, which we perform for a 28-fs pulse duration.

Emergence of currents as a transient quantum effect in nonequilibrium systems

NASA Astrophysics Data System (ADS)

Granot, Er'El; Marchewka, Avi

2011-09-01

Most current calculations are based on equilibrium or semi-equilibrium models. However, except for very special scenarios (like ring configuration), the current cannot exist in equilibrium. Moreover, unlike with equilibrium scenarios, there is no generic approach to confront out-of-equilibrium currents. In this paper we used recent studies on transient quantum mechanics to solve the current, which appears in the presence of very high density gradients and fast transients. It shows that the emerging current appears instantaneously, and although the density beyond the discontinuity is initially negligible the currents there have a finite value, and remain constant for a finite period. It is shown that this nonequilibrium effect can be measured in real experiments (such as cooled rubidium atoms), where the discontinuity is replaced with a finite width (hundreds of nanometers) gradient.

The acute and post-discontinuation effects of a glucocorticoid receptor (GR) antagonist probe on sleep and the HPA axis in chronic insomnia: a pilot study.

PubMed

Buckley, Theresa; Duggal, Vandana; Schatzberg, Alan F

2008-06-15

Hypothalamic-pituitary-adrenal axis (HPA) hyperactivity has been reported in patients with chronic insomnia without depression. Aglucocorticoid receptor (GR) antagonist may re-regulate HPA axis activity even after discontinuation and may have clinical benefit. Ten subjects with chronic insomnia participated in a placebo controlled double-blinded prospective 30-day pilot study of the acute and post-discontinuation effects of a 5-day course of 600 mg of the glucocorticoid antagonist, mifepristone. Sleep outcome measures were polysomnogram and Insomnia Severity Index. Hormonal outcome measures were mean overnight cortisol and ACTH (23:00-07:00). We predicted sleep would improve and that overnight cortisol and ACTH would decrease at 2 weeks post-treatment discontinuation. At 2 weeks post-discontinuation, Insomnia Severity Index (ISI) decreased by 4.0 points (effect size = 0.97). Polysomnogram findings were limited. Mean cortisol (0.84 microg/dL, effect size = 0.91) and ACTH (5.50 pg/mL, effect size = 0.96) were still mildly increased (23:00 to 07:00). Post hoc analysis revealed that, the ratio of cortisol/ ACTH decreased (-0.21, effect size = 1.15) as did mean cortisol from 18:00 to 23:00 (-0.47 microg/dL, effect size = 0.56). This is the first study of a GR antagonist in chronic insomnia. Sleep improvement manifests in terms of decreased ISI post-treatment discontinuation. The decrease in cortisol in the early evening (18:00 to 23:00) in combination with the decrease in cortisol/ ACTH ratio may be an indicator of the longer-term biological mode of action of the drug.

The tropopause inversion layer in models and analyses

NASA Astrophysics Data System (ADS)

Birner, T.; Sankey, D.; Shepherd, T. G.

2006-07-01

Recent high-resolution radiosonde climatologies have revealed a tropopause inversion layer (TIL) in the extratropics: temperature strongly increases just above a sharp local cold point tropopause. Here, it is asked to what extent a TIL exists in current general circulation models (GCMs) and meteorological analyses. Only a weak hint of a TIL exists in NCEP/NCAR reanalysis data. In contrast, the Canadian Middle Atmosphere Model (CMAM), a comprehensive GCM, exhibits a TIL of realistic strength. However, in data assimilation mode CMAM exhibits a much weaker TIL, especially in the Southern Hemisphere where only coarse satellite data are available. The discrepancy between the analyses and the GCM is thus hypothesized to be mainly due to data assimilation acting to smooth the observed strong curvature in temperature around the tropopause. This is confirmed in the reanalysis where the stratification around the tropopause exhibits a strong discontinuity at the start of the satellite era.

Large Eddy Simulation of Cryogenic Injection Processes at Supercritical Pressure

NASA Technical Reports Server (NTRS)

Oefelein, Joseph C.; Garcia, Roberto (Technical Monitor)

2002-01-01

This paper highlights results from the first of a series of hierarchical simulations aimed at assessing the modeling requirements for application of the large eddy simulation technique to cryogenic injection and combustion processes in liquid rocket engines. The focus is on liquid-oxygen-hydrogen coaxial injectors at a condition where the liquid-oxygen is injected at a subcritical temperature into a supercritical environment. For this situation a diffusion dominated mode of combustion occurs in the presence of exceedingly large thermophysical property gradients. Though continuous, these gradients approach the behavior of a contact discontinuity. Significant real gas effects and transport anomalies coexist locally in colder regions of the flow, with ideal gas and transport characteristics occurring within the flame zone. The current focal point is on the interfacial region between the liquid-oxygen core and the coaxial hydrogen jet where the flame anchors itself.

A nonsingular model of the open magnetosphere

NASA Technical Reports Server (NTRS)

Toffoletto, F. R.; Hill, T. W.

1993-01-01

We present a modified version of the Toffoletto and Hill (1989) open magnetosphere model that incorporates a tail-like interconection field with a discontinuity 10 represent the slow-mode expansion fan that defines the high-latitude tail magnetopause. (The interconnection field is defined as the perturbation on an initially closed magnetosphere model to make it open.) The expansion fan controls the open field line region in the tail, and the intersection of the fan with the tail current sheet is, by design, the x line. The new interconnection field allows greater control of the tail field structure; in particular, it enables us to eliminate the nightside mapping singularity that occurs in previous models when the interplanetary magnetic field is nonsouthward. Also, in contrast to earlier models, the far tail x line extends farther downstream on the flanks than in the center of the tail, consistent with observations.

Composite Nanomechanics: A Mechanistic Properties Prediction

NASA Technical Reports Server (NTRS)

Chamis, Christos C.; Handler, Louis M.; Manderscheid, Jane M.

2007-01-01

A unique mechanistic theory is described to predict the properties of nanocomposites. The theory is based on composite micromechanics with progressive substructuring down to a nanoscale slice of a nanofiber where all the governing equations are formulated. These equations hav e been programmed in a computer code. That computer code is used to predict 25 properties of a mononanofiber laminate. The results are pr esented graphically and discussed with respect to their practical sig nificance. Most of the results show smooth distributions. Results for matrix-dependent properties show bimodal through-the-thickness distr ibution with discontinuous changes from mode to mode.

The boundary between the Indian and Asian tectonic plates below Tibet

PubMed Central

Zhao, Junmeng; Yuan, Xiaohui; Liu, Hongbing; Kumar, Prakash; Pei, Shunping; Kind, Rainer; Zhang, Zhongjie; Teng, Jiwen; Ding, Lin; Gao, Xing; Xu, Qiang; Wang, Wei

2010-01-01

The fate of the colliding Indian and Asian tectonic plates below the Tibetan high plateau may be visualized by, in addition to seismic tomography, mapping the deep seismic discontinuities, like the crust-mantle boundary (Moho), the lithosphere-asthenosphere boundary (LAB), or the discontinuities at 410 and 660 km depth. We herein present observations of seismic discontinuities with the P and S receiver function techniques beneath central and western Tibet along two new profiles and discuss the results in connection with results from earlier profiles, which did observe the LAB. The LAB of the Indian and Asian plates is well-imaged by several profiles and suggests a changing mode of India-Asia collision in the east-west direction. From eastern Himalayan syntaxis to the western edge of the Tarim Basin, the Indian lithosphere is underthrusting Tibet at an increasingly shallower angle and reaching progressively further to the north. A particular lithospheric region was formed in northern and eastern Tibet as a crush zone between the two colliding plates, the existence of which is marked by high temperature, low mantle seismic wavespeed (correlating with late arriving signals from the 410 discontinuity), poor Sn propagation, east and southeast oriented global positioning system displacements, and strikingly larger seismic (SKS) anisotropy. PMID:20534567

The boundary between the Indian and Asian tectonic plates below Tibet.

PubMed

Zhao, Junmeng; Yuan, Xiaohui; Liu, Hongbing; Kumar, Prakash; Pei, Shunping; Kind, Rainer; Zhang, Zhongjie; Teng, Jiwen; Ding, Lin; Gao, Xing; Xu, Qiang; Wang, Wei

2010-06-22

The fate of the colliding Indian and Asian tectonic plates below the Tibetan high plateau may be visualized by, in addition to seismic tomography, mapping the deep seismic discontinuities, like the crust-mantle boundary (Moho), the lithosphere-asthenosphere boundary (LAB), or the discontinuities at 410 and 660 km depth. We herein present observations of seismic discontinuities with the P and S receiver function techniques beneath central and western Tibet along two new profiles and discuss the results in connection with results from earlier profiles, which did observe the LAB. The LAB of the Indian and Asian plates is well-imaged by several profiles and suggests a changing mode of India-Asia collision in the east-west direction. From eastern Himalayan syntaxis to the western edge of the Tarim Basin, the Indian lithosphere is underthrusting Tibet at an increasingly shallower angle and reaching progressively further to the north. A particular lithospheric region was formed in northern and eastern Tibet as a crush zone between the two colliding plates, the existence of which is marked by high temperature, low mantle seismic wavespeed (correlating with late arriving signals from the 410 discontinuity), poor Sn propagation, east and southeast oriented global positioning system displacements, and strikingly larger seismic (SKS) anisotropy.

Inter-Method Reliability of School Effectiveness Measures: A Comparison of Value-Added and Regression Discontinuity Estimates

ERIC Educational Resources Information Center

Perry, Thomas

2017-01-01

Value-added (VA) measures are currently the predominant approach used to compare the effectiveness of schools. Recent educational effectiveness research, however, has developed alternative approaches including the regression discontinuity (RD) design, which also allows estimation of absolute school effects. Initial research suggests RD is a viable…

76 FR 55471 - Pittsburgh & West Virginia Railroad-Abandonment Exemption-in Allegheny County, PA; Wheeling...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-07

... Pittsburgh & West Virginia Railroad (PWV) and Wheeling & Lake Erie Railway Company (WLE) (collectively... Abandonments and Discontinuances of Service for PWV to abandon, and for WLE to discontinue its sublease rights... Service Zip Code 15220. Currently, PWV leases the line to Norfolk Southern Railway Company (NSR), which in...

Effect of nonlinear energy transport on neoclassical tearing mode stability in tokamak plasmas

NASA Astrophysics Data System (ADS)

Fitzpatrick, Richard

2017-05-01

An investigation is made into the effect of the reduction in anomalous perpendicular electron heat transport inside the separatrix of a magnetic island chain associated with a neoclassical tearing mode in a tokamak plasma, due to the flattening of the electron temperature profile in this region, on the overall stability of the mode. The onset of the neoclassical tearing mode is governed by the ratio of the divergences of the parallel and perpendicular electron heat fluxes in the vicinity of the island chain. By increasing the degree of transport reduction, the onset of the mode, as the divergence ratio is gradually increased, can be made more and more abrupt. Eventually, when the degree of transport reduction passes a certain critical value, the onset of the neoclassical tearing mode becomes discontinuous. In other words, when some critical value of the divergence ratio is reached, there is a sudden bifurcation to a branch of neoclassical tearing mode solutions. Moreover, once this bifurcation has been triggered, the divergence ratio must be reduced by a substantial factor to trigger the inverse bifurcation.

Ultrasonic guided wave propagation across waveguide transitions: energy transfer and mode conversion.

PubMed

Puthillath, Padmakumar; Galan, Jose M; Ren, Baiyang; Lissenden, Cliff J; Rose, Joseph L

2013-05-01

Ultrasonic guided wave inspection of structures containing adhesively bonded joints requires an understanding of the interaction of guided waves with geometric and material discontinuities or transitions in the waveguide. Such interactions result in mode conversion with energy being partitioned among the reflected and transmitted modes. The step transition between an aluminum layer and an aluminum-adhesive-aluminum multi-layer waveguide is analyzed as a model structure. Dispersion analysis enables assessment of (i) synchronism through dispersion curve overlap and (ii) wavestructure correlation. Mode-pairs in the multi-layer waveguide are defined relative to a prescribed mode in a single layer as being synchronized and having nearly perfect wavestructure matching. Only a limited number of mode-pairs exist, and each has a unique frequency range. A hybrid model based on semi-analytical finite elements and the normal mode expansion is implemented to assess mode conversion at a step transition in a waveguide. The model results indicate that synchronism and wavestructure matching is associated with energy transfer through the step transition, and that the energy of an incident wave mode in a single layer is transmitted almost entirely to the associated mode-pair, where one exists. This analysis guides the selection of incident modes that convert into transmitted modes and improve adhesive joint inspection with ultrasonic guided waves.

Surface wave scattering from sharp lateral discontinuities

NASA Astrophysics Data System (ADS)

Pollitz, Fred F.

1994-11-01

The problem of surface wave scattering is re-explored, with quasi-degenerate normal mode coupling as the starting point. For coupling among specified spheroidal and toroidal mode dispersion branches, a set of coupled wave equations is derived in the frequency domain for first-arriving Rayleigh and Love waves. The solutions to these coupled wave equations using linear perturbation theory are surface integrals over the unit sphere covering the lateral distribution of perturbations in Earth structure. For isotropic structural perturbations and surface topographic perturbations, these solutions agree with the Born scattering theory previously obtained by Snieder and Romanowicz. By transforming these surface integrals into line integrals along the boundaries of the heterogeneous regions in the case of sharp discontinuities, and by using uniformly valid Green's functions, it is possible to extend the solution to the case of multiple scattering interactions. The proposed method allows the relatively rapid calculation of exact second order scattered wavefield potentials for scattering by sharp discontinuities, and it has many advantages not realized in earlier treatments. It employs a spherical Earth geometry, uses no far field approximation, and implicitly contains backward as well as forward scattering. Comparisons of asymptotic scattering and an exact solution with single scattering and multiple scattering integral formulations show that the phase perturbation predicted by geometrical optics breaks down for scatterers less than about six wavelengths in diameter, and second-order scattering predicts well both the amplitude and phase pattern of the exact wavefield for sufficiently small scatterers, less than about three wavelengths in diameter for anomalies of a few percent.

Magnetic field dissipation in D-sheets

NASA Technical Reports Server (NTRS)

Burlaga, L. F.; Scudder, J. D.

1973-01-01

The effects of magnetic field annihilation at a tangential or rotational discontinuity in a resistive plasma are examined. The magnetic field intensity profile depends on (1) the field intensities far from the current sheet (+ and - infinity), (2) the angle between the two intensities, and (3) the electrical resistivity. For a tangential discontinuity, the theory predicts a depression in B, centered at the discontinuity, and it predicts a monotonic transition. The theory provides satisfactory fits to the magnetic field intensity and proton temperature profiles observed for two extremely broad D-sheets in the solar wind. Assuming a diffusion time 10 days, one obtains effective resistivities or approximately = 3 x 10 to the 12th power and 2 x 10 to the 13th power emu for the D-sheets. Either resistivity at directional discontinuities is much lower than 10 to the 12th power emu or annihilation does not always occur at discontinuities.

Nonequilibrium restoration of duality symmetry in the vicinity of the superconductor-to-insulator transition

NASA Astrophysics Data System (ADS)

Tamir, I.; Doron, A.; Levinson, T.; Gorniaczyk, F.; Tewari, G. C.; Shahar, D.

2017-09-01

The magnetic field driven superconductor-to-insulator transition in thin films is theoretically understood in terms of the notion of vortex-charge duality symmetry. The manifestation of such symmetry is the exchange of roles of current and voltage between the superconductor and the insulator. While experimental evidence obtained from amorphous indium oxide films supported such duality symmetry, it is shown to be broken, counterintuitively, at low temperatures where the insulating phase exhibits discontinuous current-voltage characteristics. Here, we demonstrate that it is possible to effectively restore duality symmetry by driving the system beyond the discontinuity into its high current, far from equilibrium, state.

Strain tolerant microfilamentary superconducting wire

DOEpatents

Finnemore, D.K.; Miller, T.A.; Ostenson, J.E.; Schwartzkopf, L.A.; Sanders, S.C.

1993-02-23

A strain tolerant microfilamentary wire capable of carrying superconducting currents is provided comprising a plurality of discontinuous filaments formed from a high temperature superconducting material. The discontinuous filaments have a length at least several orders of magnitude greater than the filament diameter and are sufficiently strong while in an amorphous state to withstand compaction. A normal metal is interposed between and binds the discontinuous filaments to form a normal metal matrix capable of withstanding heat treatment for converting the filaments to a superconducting state. The geometry of the filaments within the normal metal matrix provides substantial filament-to-filament overlap, and the normal metal is sufficiently thin to allow supercurrent transfer between the overlapped discontinuous filaments but is also sufficiently thick to provide strain relief to the filaments.

Management applications of discontinuity theory | Science ...

EPA Pesticide Factsheets

1.Human impacts on the environment are multifaceted and can occur across distinct spatiotemporal scales. Ecological responses to environmental change are therefore difficult to predict, and entail large degrees of uncertainty. Such uncertainty requires robust tools for management to sustain ecosystem goods and services and maintain resilient ecosystems. 2.We propose an approach based on discontinuity theory that accounts for patterns and processes at distinct spatial and temporal scales, an inherent property of ecological systems. Discontinuity theory has not been applied in natural resource management and could therefore improve ecosystem management because it explicitly accounts for ecological complexity. 3.Synthesis and applications. We highlight the application of discontinuity approaches for meeting management goals. Specifically, discontinuity approaches have significant potential to measure and thus understand the resilience of ecosystems, to objectively identify critical scales of space and time in ecological systems at which human impact might be most severe, to provide warning indicators of regime change, to help predict and understand biological invasions and extinctions and to focus monitoring efforts. Discontinuity theory can complement current approaches, providing a broader paradigm for ecological management and conservation This manuscript provides insight on using discontinuity approaches to aid in managing complex ecological systems. In part

A simulation study on the mode conversion process from slow Z-mode to LO mode by the tunneling effect and variations of beaming angle

NASA Astrophysics Data System (ADS)

Kalaee, Mohammad Javad; Katoh, Yuto

2014-12-01

For a particular angle of incidence wave, it is possible for a slow Z-mode wave incident on an inhomogeneous plasma slab to be converted into an LO mode wave. But for another wave normal angle of the incident wave, it has been considered impossible, since an evanescence region exists between two mode branches. In this case we expect that the mode conversion takes place through the tunneling effect. We investigate the effect of the spatial scale of the density gradient on the mode conversion efficiency in an inhomogeneous plasma where the mode conversion can occur only by the tunneling effect. We use the computer simulation solving Maxwell's equations and the motion of a cold electron fluid. By considering the steepness of the density gradient, the simulation results show the efficient mode conversion could be expected even in the case that the mismatch of the refractive indexes prevents the close coupling of plasma waves. Also, we show for these cases the beaming angle does not correspond to Jones' formula. This effect leads to the angles larger and smaller than the angle estimated by the formula. This type of mode conversion process becomes important in a case where the different plasmas form a discontinuity at their contact boundary.

Multiplexed displacement fiber sensor using thin core fiber exciter.

PubMed

Chen, Zhen; Hefferman, Gerald; Wei, Tao

2015-06-01

This letter reports a multiplexed optical displacement sensor using a thin core fiber (TCF) exciter. The TCF exciter is followed by a stripped single mode optical fiber. A small section of buffer is used as the movable component along the single mode fiber. Ultra-weak cladding mode reflection (< - 75 dB) was employed to probe the refractive index discontinuity between the air and buffer coating boundary. The position change of the movable buffer segment results in a delay change of the cladding mode reflection. Thus, it is a measure of the displacement of the buffer segment with respect to the glass fiber. The insertion loss of one sensor was measured to be less than 3 dB. A linear relationship was evaluated between the measurement position and absolute position of the moving actuator. Multiplexed capability was demonstrated and no cross talk was found between the sensors.

Patterns and processes in the California Current System

NASA Astrophysics Data System (ADS)

Checkley, David M., Jr.; Barth, John A.

2009-12-01

The California Current System (CCS) is forced by the distribution of atmospheric pressure and associated winds in relation to the west coast of North America. In this paper, we begin with a simplified case of winds and a linear coast, then consider variability characteristic of the CCS, and conclude by considering future change. The CCS extends from the North Pacific Current (∼50°N) to off Baja California, Mexico (∼15-25°N) with a major discontinuity at Point Conception (34.5°N). Variation in atmospheric pressure affects winds and thus upwelling. Coastal, wind-driven upwelling results in nutrification and biological production and a southward coastal jet. Offshore, curl-driven upwelling results in a spatially large, productive habitat. The California Current flows equatorward and derives from the North Pacific Current and the coastal jet. Dominant modes of spatial and temporal variability in physical processes and biological responses are discussed. High surface production results in deep and bottom waters depleted in oxygen and enriched in carbon dioxide. Fishing has depleted demersal stocks more than pelagic stocks, and marine mammals, including whales, are recovering. Krill, squid, and micronekton are poorly known and merit study. Future climate change will differ from past change and thus prediction of the CCS requires an understanding of its dynamics. Of particular concern are changes in winds, stratification, and ocean chemistry.

The derivative discontinuity of the exchange-correlation functional.

PubMed

Mori-Sánchez, Paula; Cohen, Aron J

2014-07-28

The derivative discontinuity is a key concept in electronic structure theory in general and density functional theory in particular. The electronic energy of a quantum system exhibits derivative discontinuities with respect to different degrees of freedom that are a consequence of the integer nature of electrons. The classical understanding refers to the derivative discontinuity of the total energy as a function of the total number of electrons (N), but it can also manifest at constant N. Examples are shown in models including several hydrogen systems with varying numbers of electrons or nuclear charge (Z), as well as the 1-dimensional Hubbard model (1DHM). Two sides of the problem are investigated: first, the failure of currently used approximate exchange-correlation functionals in DFT and, second, the importance of the derivative discontinuity in the exact electronic structure of molecules, as revealed by full configuration interaction (FCI). Currently, all approximate functionals, including hybrids, miss the derivative discontinuity, leading to basic errors that can be seen in many ways: from the complete failure to give the total energy of H2 and H2(+), to the missing gap in Mott insulators such as stretched H2 and the thermodynamic limit of the 1DHM, or a qualitatively incorrect density in the HZ molecule with two electrons and incorrect electron transfer processes. Description of the exact particle behaviour of electrons is emphasised, which is key to many important physical processes in real systems, especially those involving electron transfer, and offers a challenge for the development of new exchange-correlation functionals.

Multi-phase arrival tracking using tetrahedral cells within a 3D layered titled transversely isotropic anisotropic model involving undulating topography and irregular interfaces

NASA Astrophysics Data System (ADS)

Li, Xing-Wang; Bai, Chao-Ying; Yue, Xiao-Peng; Greenhalgh, Stewart

2018-02-01

To overcome a major problem in current ray tracing methods, which are only capable of tracing first arrivals, and occasionally primary reflections (or mode conversions) in regular cell models, we extend in this paper the multistage triangular shortest-path method (SPM) into 3D titled transversely isotropic (TTI) anisotropic media. The proposed method is capable of tracking multi-phase arrivals composed of any kind of combinations of transmissions, mode conversions and reflections. In model parameterization, five elastic parameters, plus two angles defining the titled axis of symmetry of TTI media are sampled at the primary nodes of the tetrahedral cell, and velocity value at secondary node positions are linked by a tri-linear velocity interpolation function to the primary node velocity value of that of a tetrahedral cell, from which the group velocities of the three wave modes (qP, qSV and qSH) are computed. The multistage triangular SPM is used to track multi-phase arrivals. The uniform anisotropic test indicates that the numerical solution agrees well with the analytic solution, thus verifying the accuracy of the methodology. Several simulations and comparison results for heterogeneous models show that the proposed algorithm is able to efficiently and accurately approximate undulating surface topography and irregular subsurface velocity discontinuities. It is suitable for any combination of multi-phase arrival tracking in arbitrary tilt angle TTI media and can accommodate any magnitude of anisotropy.

Perspectives on holoprosencephaly: Part III. Spectra, distinctions, continuities, and discontinuities.

PubMed

Cohen, M M

1989-10-01

This paper attempts to balance our knowledge of holoprosencephalic spectra and continuities with important distinctions and discontinuities. Prevalence studies and syndrome delineation are briefly reviewed. The following topics receive detailed coverage: human teratogens, special aspects of forebrain and hindbrain malformations, aprosencephaly/atelencephaly, association with neural tube defects, current assessment of "facial principles," and endocrine abnormalities.

What factors are associated with current smokers using or stopping e-cigarette use?

PubMed

Simonavicius, Erikas; McNeill, Ann; Arnott, Deborah; Brose, Leonie S

2017-04-01

While some smokers use e-cigarettes and stop smoking, a substantial proportion try e-cigarettes and later discontinue or use them concurrently with smoking (current dual users). The aim was to assess factors associated with ongoing e-cigarette use and discontinuation among smokers. Secondary analysis of data of 1489 currently smoking adults, 18 and above, from a GB population-based online survey conducted in March 2016. A multivariable logistic regression assessed motivation to stop smoking among never e-cigarette users, past triers (

Adaptive Actor-Critic Design-Based Integral Sliding-Mode Control for Partially Unknown Nonlinear Systems With Input Disturbances.

PubMed

Fan, Quan-Yong; Yang, Guang-Hong

2016-01-01

This paper is concerned with the problem of integral sliding-mode control for a class of nonlinear systems with input disturbances and unknown nonlinear terms through the adaptive actor-critic (AC) control method. The main objective is to design a sliding-mode control methodology based on the adaptive dynamic programming (ADP) method, so that the closed-loop system with time-varying disturbances is stable and the nearly optimal performance of the sliding-mode dynamics can be guaranteed. In the first step, a neural network (NN)-based observer and a disturbance observer are designed to approximate the unknown nonlinear terms and estimate the input disturbances, respectively. Based on the NN approximations and disturbance estimations, the discontinuous part of the sliding-mode control is constructed to eliminate the effect of the disturbances and attain the expected equivalent sliding-mode dynamics. Then, the ADP method with AC structure is presented to learn the optimal control for the sliding-mode dynamics online. Reconstructed tuning laws are developed to guarantee the stability of the sliding-mode dynamics and the convergence of the weights of critic and actor NNs. Finally, the simulation results are presented to illustrate the effectiveness of the proposed method.

Management applications of discontinuity theory

USGS Publications Warehouse

Angeler, David G.; Allen, Craig R.; Barichievy, Chris; Eason, Tarsha; Garmestani, Ahjond S.; Graham, Nicholas A.J.; Granholm, Dean; Gunderson, Lance H.; Knutson, Melinda; Nash, Kirsty L.; Nelson, R. John; Nystrom, Magnus; Spanbauer, Trisha; Stow, Craig A.; Sundstrom, Shana M.

2015-01-01

Human impacts on the environment are multifaceted and can occur across distinct spatiotemporal scales. Ecological responses to environmental change are therefore difficult to predict, and entail large degrees of uncertainty. Such uncertainty requires robust tools for management to sustain ecosystem goods and services and maintain resilient ecosystems.We propose an approach based on discontinuity theory that accounts for patterns and processes at distinct spatial and temporal scales, an inherent property of ecological systems. Discontinuity theory has not been applied in natural resource management and could therefore improve ecosystem management because it explicitly accounts for ecological complexity.Synthesis and applications. We highlight the application of discontinuity approaches for meeting management goals. Specifically, discontinuity approaches have significant potential to measure and thus understand the resilience of ecosystems, to objectively identify critical scales of space and time in ecological systems at which human impact might be most severe, to provide warning indicators of regime change, to help predict and understand biological invasions and extinctions and to focus monitoring efforts. Discontinuity theory can complement current approaches, providing a broader paradigm for ecological management and conservation.

Three-Dimensional Passive-Source Reverse-Time Migration of Converted Waves: The Method

NASA Astrophysics Data System (ADS)

Li, Jiahang; Shen, Yang; Zhang, Wei

2018-02-01

At seismic discontinuities in the crust and mantle, part of the compressional wave energy converts to shear wave, and vice versa. These converted waves have been widely used in receiver function (RF) studies to image discontinuity structures in the Earth. While generally successful, the conventional RF method has its limitations and is suited mostly to flat or gently dipping structures. Among the efforts to overcome the limitations of the conventional RF method is the development of the wave-theory-based, passive-source reverse-time migration (PS-RTM) for imaging complex seismic discontinuities and scatters. To date, PS-RTM has been implemented only in 2D in the Cartesian coordinate for local problems and thus has limited applicability. In this paper, we introduce a 3D PS-RTM approach in the spherical coordinate, which is better suited for regional and global problems. New computational procedures are developed to reduce artifacts and enhance migrated images, including back-propagating the main arrival and the coda containing the converted waves separately, using a modified Helmholtz decomposition operator to separate the P and S modes in the back-propagated wavefields, and applying an imaging condition that maintains a consistent polarity for a given velocity contrast. Our new approach allows us to use migration velocity models with realistic velocity discontinuities, improving accuracy of the migrated images. We present several synthetic experiments to demonstrate the method, using regional and teleseismic sources. The results show that both regional and teleseismic sources can illuminate complex structures and this method is well suited for imaging dipping interfaces and sharp lateral changes in discontinuity structures.

A Streaming Language Implementation of the Discontinuous Galerkin Method

NASA Technical Reports Server (NTRS)

Barth, Timothy; Knight, Timothy

2005-01-01

We present a Brook streaming language implementation of the 3-D discontinuous Galerkin method for compressible fluid flow on tetrahedral meshes. Efficient implementation of the discontinuous Galerkin method using the streaming model of computation introduces several algorithmic design challenges. Using a cycle-accurate simulator, performance characteristics have been obtained for the Stanford Merrimac stream processor. The current Merrimac design achieves 128 Gflops per chip and the desktop board is populated with 16 chips yielding a peak performance of 2 Teraflops. Total parts cost for the desktop board is less than $20K. Current cycle-accurate simulations for discretizations of the 3-D compressible flow equations yield approximately 40-50% of the peak performance of the Merrimac streaming processor chip. Ongoing work includes the assessment of the performance of the same algorithm on the 2 Teraflop desktop board with a target goal of achieving 1 Teraflop performance.

Inverse problems for torsional modes.

USGS Publications Warehouse

Willis, C.

1984-01-01

Considers a spherically symmetric, non-rotating Earth consisting of an isotropic, perfect elastic material where the density and the S-wave velocity may have one or two discontinuities in the upper mantle. Shows that given the velocity throughout the mantle and the crust and given the density in the lower mantle, then the freqencies of the torsional oscillations of one angular order (one torsional spectrum), determine the density in the upper mantle and in the crust uniquely. If the velocity is known only in the lower mantle, then the frequencies of the torsional oscillations of two angular orders uniquely determine both the density and the velocity in the upper mantle and in the crust. In particular, the position and size of the discontinuities in the density and velocity are uniquely determined by two torsional spectra.-Author

Method for producing strain tolerant multifilamentary oxide superconducting wire

DOEpatents

Finnemore, D.K.; Miller, T.A.; Ostenson, J.E.; Schwartzkopf, L.A.; Sanders, S.C.

1994-07-19

A strain tolerant multifilamentary wire capable of carrying superconducting currents is provided comprising a plurality of discontinuous filaments formed from a high temperature superconducting material. The discontinuous filaments have a length at least several orders of magnitude greater than the filament diameter and are sufficiently strong while in an amorphous state to withstand compaction. A normal metal is interposed between and binds the discontinuous filaments to form a normal metal matrix capable of withstanding heat treatment for converting the filaments to a superconducting state. The geometry of the filaments within the normal metal matrix provides substantial filament-to-filament overlap, and the normal metal is sufficiently thin to allow supercurrent transfer between the overlapped discontinuous filaments but is also sufficiently thick to provide strain relief to the filaments. 6 figs.

Method for producing strain tolerant multifilamentary oxide superconducting wire

DOEpatents

Finnemore, Douglas K.; Miller, Theodore A.; Ostenson, Jerome E.; Schwartzkopf, Louis A.; Sanders, Steven C.

1994-07-19

A strain tolerant multifilamentary wire capable of carrying superconducting currents is provided comprising a plurality of discontinuous filaments formed from a high temperature superconducting material. The discontinuous filaments have a length at least several orders of magnitude greater than the filament diameter and are sufficiently strong while in an amorphous state to withstand compaction. A normal metal is interposed between and binds the discontinuous filaments to form a normal metal matrix capable of withstanding heat treatment for converting the filaments to a superconducting state. The geometry of the filaments within the normal metal matrix provides substantial filament-to-filament overlap, and the normal metal is sufficiently thin to allow supercurrent transfer between the overlapped discontinuous filaments but is also sufficiently thick to provide strain relief to the filaments.

Interface failure modes explain non-monotonic size-dependent mechanical properties in bioinspired nanolaminates.

PubMed

Song, Z Q; Ni, Y; Peng, L M; Liang, H Y; He, L H

2016-03-31

Bioinspired discontinuous nanolaminate design becomes an efficient way to mitigate the strength-ductility tradeoff in brittle materials via arresting the crack at the interface followed by controllable interface failure. The analytical solution and numerical simulation based on the nonlinear shear-lag model indicates that propagation of the interface failure can be unstable or stable when the interfacial shear stress between laminae is uniform or highly localized, respectively. A dimensionless key parameter defined by the ratio of two characteristic lengths governs the transition between the two interface-failure modes, which can explain the non-monotonic size-dependent mechanical properties observed in various laminate composites.

Micro-mechanical analysis of damage growth and fracture in discontinuous fiber reinforced metal matrix composites

NASA Technical Reports Server (NTRS)

Goree, James G.; Richardson, David E.

1990-01-01

The near-crack-tip stresses in any planar coupon of arbitrary geometry subjected to mode 1 loading may be equated to those in an infinite center-cracked panel subjected to the appropriate equivalent remote biaxial stresses (ERBS). Since this process can be done for all such mode 1 coupons, attention may be focused on the behavior of the equivalent infinite cracked panel. To calculate the ERBS, the constant term in the series expansion of the crack-tip stress must be retained. It is proposed that the ERBS may be used quantitatively to explain different fracture phenomena such as crack branching.

Uncertainty Quantification for Robust Control of Wind Turbines using Sliding Mode Observer

NASA Astrophysics Data System (ADS)

Schulte, Horst

2016-09-01

A new quantification method of uncertain models for robust wind turbine control using sliding-mode techniques is presented with the objective to improve active load mitigation. This approach is based on the so-called equivalent output injection signal, which corresponds to the average behavior of the discontinuous switching term, establishing and maintaining a motion on a so-called sliding surface. The injection signal is directly evaluated to obtain estimates of the uncertainty bounds of external disturbances and parameter uncertainties. The applicability of the proposed method is illustrated by the quantification of a four degree-of-freedom model of the NREL 5MW reference turbine containing uncertainties.

The Prekindergarten Age-Cutoff Regression-Discontinuity Design: Methodological Issues and Implications for Application

ERIC Educational Resources Information Center

Lipsey, Mark W.; Weiland, Christina; Yoshikawa, Hirokazu; Wilson, Sandra Jo; Hofer, Kerry G.

2015-01-01

Much of the currently available evidence on the causal effects of public prekindergarten programs on school readiness outcomes comes from studies that use a regression-discontinuity design (RDD) with the age cutoff to enter a program in a given year as the basis for assignment to treatment and control conditions. Because the RDD has high internal…

TURBULENCE-GENERATED PROTON-SCALE STRUCTURES IN THE TERRESTRIAL MAGNETOSHEATH

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vörös, Zoltán; Narita, Yasuhito; Yordanova, Emiliya

2016-03-01

Recent results of numerical magnetohydrodynamic simulations suggest that in collisionless space plasmas, turbulence can spontaneously generate thin current sheets. These coherent structures can partially explain the intermittency and the non-homogenous distribution of localized plasma heating in turbulence. In this Letter, Cluster multi-point observations are used to investigate the distribution of magnetic field discontinuities and the associated small-scale current sheets in the terrestrial magnetosheath downstream of a quasi-parallel bow shock. It is shown experimentally, for the first time, that the strongest turbulence-generated current sheets occupy the long tails of probability distribution functions associated with extremal values of magnetic field partial derivatives.more » During the analyzed one-hour time interval, about a hundred strong discontinuities, possibly proton-scale current sheets, were observed.« less

Interferon alpha 2 maintenance therapy may enable high rates of treatment discontinuation in chronic myeloid leukemia.

PubMed

Burchert, A; Saussele, S; Eigendorff, E; Müller, M C; Sohlbach, K; Inselmann, S; Schütz, C; Metzelder, S K; Ziermann, J; Kostrewa, P; Hoffmann, J; Hehlmann, R; Neubauer, A; Hochhaus, A

2015-06-01

A minority of chronic myeloid leukemia (CML) patients is capable of successfully discontinuing imatinib. Treatment modalities to increase this proportion are currently unknown. Here, we assessed the role of interferon alpha 2a (IFN) on therapy discontinuation in a previously reported cohort of 20 chronic phase CML patients who were treated upfront with IFN alpha plus imatinib followed by IFN monotherapy to maintain cytogenetic or molecular remission (MR) after imatinib discontinuation. After a median follow-up of 7.9 years (range, 5.2-12.2), relapse-free survival was 73% (8/11 patients) and 84% (5/6 patients) for patients who discontinued imatinib in major MR (MMR) and MR4/MR4.5, respectively. Ten patients discontinued IFN after a median of 4.5 years (range, 0.24-9.3). After a median of 2.8 years (range, 0.7-5.1), nine of them remain in ongoing treatment-free remission with MR5 (n=6) and MR4.5 (n=3). The four patients who still administer IFN are in stable MR5, MR4.5, MR4, and MMR, respectively. In conclusion, an IFN/imatinib induction treatment followed by a temporary IFN maintenance therapy may enable a high rate of treatment discontinuation in CML patients in at least MMR when stopping imatinib.

Mantle transition zone beneath central-eastern Greenland: Possible evidence for a deep tectosphere from receiver functions

NASA Astrophysics Data System (ADS)

Kraft, Helene Anja; Vinnik, Lev; Thybo, Hans

2018-03-01

We investigate the mantle of central-eastern Greenland by using recordings with data from 24 local broad-band seismograph stations. We apply P wave receiver function technique and evaluate the difference in the arrival times of seismic phases that are formed by P to SV mode conversion at the 410-km and 660-km seismic discontinuities. These boundaries mark the top and bottom of the mantle transition zone (MTZ). The difference in the arrival time of the phases from the 410-km and 660-km discontinuities is sensitive to the thickness of the MTZ and relatively insensitive to volumetric velocity anomalies above the 410-km discontinuity. Near the east coast of Greenland in the region of the Skaergaard basalt intrusions we find two regions where the differential time is reduced by more than 2 s. The 410-km discontinuity in these regions is depressed by more than 20 km. The depression may be explained by a temperature elevation of 150 °C. We hypothesize that the basaltic intrusions and the temperature anomalies at a depth of 400 km are, at least partly, effects of the passage of Greenland over the Iceland hotspot at about 55 Ma. This explanation is consistent with the concept of tectosphere and implies that the upper mantle to a depth of 400 km translates coherently with the Greenland plate.

Fracture Capabilities in Grizzly with the extended Finite Element Method (X-FEM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dolbow, John; Zhang, Ziyu; Spencer, Benjamin

Efforts are underway to develop fracture mechanics capabilities in the Grizzly code to enable it to be used to perform deterministic fracture assessments of degraded reactor pressure vessels (RPVs). A capability was previously developed to calculate three-dimensional interaction- integrals to extract mixed-mode stress-intensity factors. This capability requires the use of a finite element mesh that conforms to the crack geometry. The eXtended Finite Element Method (X-FEM) provides a means to represent a crack geometry without explicitly fitting the finite element mesh to it. This is effected by enhancing the element kinematics to represent jump discontinuities at arbitrary locations inside ofmore » the element, as well as the incorporation of asymptotic near-tip fields to better capture crack singularities. In this work, use of only the discontinuous enrichment functions was examined to see how accurate stress intensity factors could still be calculated. This report documents the following work to enhance Grizzly’s engineering fracture capabilities by introducing arbitrary jump discontinuities for prescribed crack geometries; X-FEM Mesh Cutting in 3D: to enhance the kinematics of elements that are intersected by arbitrary crack geometries, a mesh cutting algorithm was implemented in Grizzly. The algorithm introduces new virtual nodes and creates partial elements, and then creates a new mesh connectivity; Interaction Integral Modifications: the existing code for evaluating the interaction integral in Grizzly was based on the assumption of a mesh that was fitted to the crack geometry. Modifications were made to allow for the possibility of a crack front that passes arbitrarily through the mesh; and Benchmarking for 3D Fracture: the new capabilities were benchmarked against mixed-mode three-dimensional fracture problems with known analytical solutions.« less

Geomorphic Evidences of Pleistocene Deformations in the Western Pyrenees (France)

NASA Astrophysics Data System (ADS)

Lacan, P.; Nivière, B.; Rousset, D.; Sénéchal, P.

2007-12-01

Due to its intraplate position, the on-going tectonic activity of the Western Pyrenees is only revealed by a moderate and diffuse seismicity. This seismicity presents a general E-W pattern and is distributed along the northern flank of the chain in the western part. We focus here on the Arudy area that suffered from one of the major Pyrenean instrumental earthquakes (M=5,1) in 1980. An early Cretaceous normal fault of the Iberian margin is probably the seismic source of this event. The late Cretaceous inversion of the margin, first in a left-lateral strike-slip mode and then in a more frontal convergence, resulted in a shallow pop-up geometry near Arudy. This pop-up attests of the presence in depth of a crustal discontinuity. The present-day geodynamic arrangement might reactivate this accident in a right lateral mode. This reactivation leads to a strain partitioning between the deep crustal discontinuity and the shallow pop-up that achieved respectively the lateral and frontal components of the displacement. Folding of Quaternary terrace remnants above the thrusts limiting the pop-up, attests of the Pleistocene activity of the structure. Growth of alluvial depocenters in the footwall of these thrusts revealed by near-surface geophysical surveys (electric tomography and ground penetrating radar) attest too of this activity. This deformation resulted in ca 1500 m long and 5-10 m high folds during the middle to late Pleistocene. Using a strain partitioning model, this quantification of the near-surface deformation allows to estimate the displacement achieved by the blind crustal discontinuity. So the seismic hazard due to this fault is better constrained. Project funded by Région Aquitaine and TTI Production.

Premature trial discontinuation often not accurately reflected in registries: comparison of registry records with publications.

PubMed

Alturki, Reem; Schandelmaier, Stefan; Olu, Kelechi Kalu; von Niederhäusern, Belinda; Agarwal, Arnav; Frei, Roy; Bhatnagar, Neera; Hooft, Lotty; von Elm, Erik; Briel, Matthias

2017-01-01

One quarter of randomized clinical trials (RCTs) are prematurely discontinued and frequently remain unpublished. Trial registries can document whether a trial is ongoing, suspended, discontinued, or completed and therefore represent an important source for trial status information. The accuracy of this information is unclear. To examine the accuracy of completion status and reasons for discontinuation documented in trial registries as compared to corresponding publications of discontinued RCTs and to investigate potential predictors for accurate trial status information in registries. We conducted a cross-sectional study comparing information provided in publications (reference standard) to corresponding registry entries. First, we reviewed publications of RCTs providing information on both discontinuation and registration. We identified eligible publications through systematic searches of MEDLINE and EMBASE (2010-2014) and an international cohort of 1,017 RCTs initiated between 2000 and 2003. Second, pairs of investigators independently and in duplicate extracted data from publications and corresponding registry records. Third, for each discontinued RCT, we compared publication information to registry information. We used multivariable regression to examine whether accurate labeling of trials as discontinued (vs. other status) in the registry was associated with recent initiation of RCT, industry sponsorship, multicenter design, or larger sample size. We identified 173 publications of RCTs that were discontinued due to slow recruitment (55%), harm (16%), futility (11%), benefit (5%), other reasons (3%), or multiple reasons (9%). Trials were registered with clinicaltrials.gov (77%), isrctn.com (14%), or other registries (8%). Of the 173 corresponding registry records, 77 (45%) trials were labeled as discontinued and 57 (33%) provided a reason for discontinuation (of which 53, 93%, provided the same reason as in the publication). Labeling of discontinued trials as discontinued (vs. other label) in corresponding trial registry records improved over time (adjusted odds ratio 1.16 per year, confidence interval 1.04-1.30) and was possibly associated with industry sponsorship (2.01, 0.99-4.07) but unlikely with multicenter status (0.81, 0.32-2.04) or sample size (1.07, 0.89-1.29). Less than half of published discontinued RCTs were accurately labelled as discontinued in corresponding registry records. One-third of registry records provided a reason for discontinuation. Current trial status information in registries should be viewed with caution. Copyright © 2016 Elsevier Inc. All rights reserved.

Natalizumab Discontinuation and Treatment Strategies in Patients with Multiple Sclerosis (MS): A Retrospective Study from Two Italian MS Centers.

PubMed

Lo Re, Marianna; Capobianco, Marco; Ragonese, Paolo; Realmuto, Sabrina; Malucchi, Simona; Berchialla, Paola; Salemi, Giuseppe; Bertolotto, Antonio

2015-12-01

Natalizumab (NTZ) discontinuation can be followed by multiple sclerosis (MS) disease reactivation. Currently no disease-modifying drug (DMD) has been shown to be able to abolish disease reactivation. The aims of the current study were: (1) to determine the frequency of MS reactivation after NTZ discontinuation; (2) to evaluate predictors of reactivation risk, and (3) to compare the effect of different treatments in reducing this risk. Data from 132 patients with MS followed-up for 2 years before NTZ treatment and 1 year after interruption were collected from two Italian MS centers and retrospectively evaluated. Overall, 72 of 132 patients (54.5%) had relapses after NTZ discontinuation and 60 of 125 patients (48%), who had magnetic resonance imaging, had radiological reactivation. Rebound was observed in 28 of 132 patients (21.2%). A higher number of relapses in the 2 years before NTZ treatment, a longer washout period, and a lower number NTZ infusions correlated with reactivation and rebound. Untreated patients (n = 37) had higher clinical and radiological activity and rebound in comparison to patients receiving DMDs. Moreover, a lower risk of relapses was found in patients treated with second-line therapies (NTZ and fingolimod) than in those treated with first-line therapies (interferon beta, glatiramer acetate, teriflunomide, azathioprine). Interestingly, no disease reactivation in off-label treatment (rituximab, autologous hematopoietic stem cell transplantation) was observed. NTZ discontinuation is a risk for MS reactivation and rebound. An alternative treatment should be promptly resumed mainly in patients with a previous very active disease course and with a shorter NTZ therapy. Second-line therapies demonstrate superiority in preventing relapses after NTZ discontinuation.

Automated extraction and analysis of rock discontinuity characteristics from 3D point clouds

NASA Astrophysics Data System (ADS)

Bianchetti, Matteo; Villa, Alberto; Agliardi, Federico; Crosta, Giovanni B.

2016-04-01

A reliable characterization of fractured rock masses requires an exhaustive geometrical description of discontinuities, including orientation, spacing, and size. These are required to describe discontinuum rock mass structure, perform Discrete Fracture Network and DEM modelling, or provide input for rock mass classification or equivalent continuum estimate of rock mass properties. Although several advanced methodologies have been developed in the last decades, a complete characterization of discontinuity geometry in practice is still challenging, due to scale-dependent variability of fracture patterns and difficult accessibility to large outcrops. Recent advances in remote survey techniques, such as terrestrial laser scanning and digital photogrammetry, allow a fast and accurate acquisition of dense 3D point clouds, which promoted the development of several semi-automatic approaches to extract discontinuity features. Nevertheless, these often need user supervision on algorithm parameters which can be difficult to assess. To overcome this problem, we developed an original Matlab tool, allowing fast, fully automatic extraction and analysis of discontinuity features with no requirements on point cloud accuracy, density and homogeneity. The tool consists of a set of algorithms which: (i) process raw 3D point clouds, (ii) automatically characterize discontinuity sets, (iii) identify individual discontinuity surfaces, and (iv) analyse their spacing and persistence. The tool operates in either a supervised or unsupervised mode, starting from an automatic preliminary exploration data analysis. The identification and geometrical characterization of discontinuity features is divided in steps. First, coplanar surfaces are identified in the whole point cloud using K-Nearest Neighbor and Principal Component Analysis algorithms optimized on point cloud accuracy and specified typical facet size. Then, discontinuity set orientation is calculated using Kernel Density Estimation and principal vector similarity criteria. Poles to points are assigned to individual discontinuity objects using easy custom vector clustering and Jaccard distance approaches, and each object is segmented into planar clusters using an improved version of the DBSCAN algorithm. Modal set orientations are then recomputed by cluster-based orientation statistics to avoid the effects of biases related to cluster size and density heterogeneity of the point cloud. Finally, spacing values are measured between individual discontinuity clusters along scanlines parallel to modal pole vectors, whereas individual feature size (persistence) is measured using 3D convex hull bounding boxes. Spacing and size are provided both as raw population data and as summary statistics. The tool is optimized for parallel computing on 64bit systems, and a Graphic User Interface (GUI) has been developed to manage data processing, provide several outputs, including reclassified point clouds, tables, plots, derived fracture intensity parameters, and export to modelling software tools. We present test applications performed both on synthetic 3D data (simple 3D solids) and real case studies, validating the results with existing geomechanical datasets.

Anomaly Detection in Test Equipment via Sliding Mode Observers

NASA Technical Reports Server (NTRS)

Solano, Wanda M.; Drakunov, Sergey V.

2012-01-01

Nonlinear observers were originally developed based on the ideas of variable structure control, and for the purpose of detecting disturbances in complex systems. In this anomaly detection application, these observers were designed for estimating the distributed state of fluid flow in a pipe described by a class of advection equations. The observer algorithm uses collected data in a piping system to estimate the distributed system state (pressure and velocity along a pipe containing liquid gas propellant flow) using only boundary measurements. These estimates are then used to further estimate and localize possible anomalies such as leaks or foreign objects, and instrumentation metering problems such as incorrect flow meter orifice plate size. The observer algorithm has the following parts: a mathematical model of the fluid flow, observer control algorithm, and an anomaly identification algorithm. The main functional operation of the algorithm is in creating the sliding mode in the observer system implemented as software. Once the sliding mode starts in the system, the equivalent value of the discontinuous function in sliding mode can be obtained by filtering out the high-frequency chattering component. In control theory, "observers" are dynamic algorithms for the online estimation of the current state of a dynamic system by measurements of an output of the system. Classical linear observers can provide optimal estimates of a system state in case of uncertainty modeled by white noise. For nonlinear cases, the theory of nonlinear observers has been developed and its success is mainly due to the sliding mode approach. Using the mathematical theory of variable structure systems with sliding modes, the observer algorithm is designed in such a way that it steers the output of the model to the output of the system obtained via a variety of sensors, in spite of possible mismatches between the assumed model and actual system. The unique properties of sliding mode control allow not only control of the model internal states to the states of the real-life system, but also identification of the disturbance or anomaly that may occur.

Direct Feeding at the Breast Is Associated with Breast Milk Feeding Duration among Preterm Infants

PubMed Central

2017-01-01

Background: In spite of high rates of initiating breast milk feeding (BMF) among preterm infants, a significant rate of discontinuation occurs shortly after discharge. Aim: To investigate the effect of mode (direct feeding at the breast vs. expressing) and exclusivity (breast milk combined with formula vs. breast milk only) as well as maternal perceptions on the duration of BMF among preterm infants. Methods: The study included mothers whose infants were born before 32 weeks gestation, between January 2012 and August 2015 at Sheba Medical Center (SMC). Perinatal data were collected retrospectively from infants’ computerized charts. Mothers were approached >12 months postpartum and were asked to complete a questionnaire. Those who agreed to participate were asked (during their visit to the follow-up clinic or by phone or mail) to complete a questionnaire regarding mode and duration of BMF as well as reasons for its discontinuation. Mothers were also asked about their pre-partum intentions to feed directly at the breast. Results: Out of 162 eligible mothers, 131 (80.8%) initiated BMF during their intensive care unit (ICU) hospitalization. Of these, 66 (50.3%) discontinued BMF earlier than six months postpartum. BMF ≥ 6 months was significantly associated with direct feeding at the breast, duration of exclusive BMF, and singleton birth. Regression analysis revealed that direct feeding at the breast (any or only) and duration of BMF exclusivity were the only significant variables associated with BMF duration (Odds ratio (OR) 5.5 and 95% confidence interval (CI) 2.00–15.37; OR 1.5 and 95% CI 1.25–1.88, respectively). Milk supply (inadequate or nonexistent) was the most commonly reported cause for BMF discontinuation <6 months. Direct feeding at the breast was significantly associated with BMF duration and was more common among singletons. Conclusions: Direct feeding at the breast and duration of exclusive BMF are associated with duration of BMF among infants born <32 weeks of gestational age (GA). These findings suggest that targeting these two factors may play a key role in prolonging BMF duration among preterm infants. PMID:29104257

Drugs in development for Parkinson's disease: an update.

PubMed

Johnston, Tom H; Brotchie, Jonathan M

2006-01-01

The current development of emerging pharmacological treatments for Parkinson's disease (PD), front preclinical to launch, is summarized. Advances over the past year are highlighted, including the significant progress of several drugs through various stages of development. Several agents have been discontinued from development, either because of adverse effects or lack of clinical efficacy. The methyl-esterified form of L-DOPA (melevodopa) and the monoamine oxidase type B inhibitor rasagiline have both been launched. With regard to the monoamine re-uptake inhibitors, many changes have been witnessed, with new agents reaching preclinical development and pre-existing ones being discontinued or having no development reported. Of the dopamine agonists, many continue to progress successfully through clinical trials. Others have struggled to demonstrate a significant advantage over currently available treatments and have been discontinued. The field of non-dopaminergic treatments remains dynamic. The alpha2 adrenergic receptor antagonists and the adenosine A2A receptor antagonists remain in clinical trials. Trials of the neuronal' synchronization modulator levetiracetam are at an advanced stage, and there has also been a new addition to the class (ie, seletracetam). There has been a change in the landscape of neuroprotective agents that modulate disease progression. Candidates from the classes of growth factors and glyceraldehyde-3-phosphate dehydrogenase inhibitors have been discontinued, or no development has been reported, and the mixed lineage kinase inhibitor CEP-1347 has been discontinued for PD treatment. Other drugs in this field, such as neuroimmunophilins, estrogens and alpha-synuclein oligomerization inhibitors, remain in development.

Simulating Flaring Events via an Intelligent Cellular Automata Mechanism

NASA Astrophysics Data System (ADS)

Dimitropoulou, M.; Vlahos, L.; Isliker, H.; Georgoulis, M.

2010-07-01

We simulate flaring events through a Cellular Automaton (CA) model, in which, for the first time, we use observed vector magnetograms as initial conditions. After non-linear force free extrapolation of the magnetic field from the vector magnetograms, we identify magnetic discontinuities, using two alternative criteria: (1) the average magnetic field gradient, or (2) the normalized magnetic field curl (i.e. the current). Magnetic discontinuities are identified at the grid-sites where the magnetic field gradient or curl exceeds a specified threshold. We then relax the magnetic discontinuities according to the rules of Lu and Hamilton (1991) or Lu et al. (1993), i.e. we redistribute the magnetic field locally so that the discontinuities disappear. In order to simulate the flaring events, we consider several alternative scenarios with regard to: (1) The threshold above which magnetic discontinuities are identified (applying low, high, and height-dependent threshold values); (2) The driving process that occasionally causes new discontinuities (at randomly chosen grid sites, magnetic field increments are added that are perpendicular (or may-be also parallel) to the existing magnetic field). We address the question whether the coronal active region magnetic fields can indeed be considered to be in the state of self-organized criticality (SOC).

Analytic wave solution with helicon and Trivelpiece-Gould modes in an annular plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlsson, Johan; Pavarin, Daniele; Walker, Mitchell

2009-11-26

Helicon sources in an annular configuration have applications for plasma thrusters. The theory of Klozenberg et al.[J. P. Klozenberg B. McNamara and P. C. Thonemann, J. Fluid Mech. 21(1965) 545-563] for the propagation and absorption of helicon and Trivelpiece-Gould modes in a cylindrical plasma has been generalized for annular plasmas. Analytic solutions are found also in the annular case, but in the presence of both helicon and Trivelpiece-Gould modes, a heterogeneous linear system of equations must be solved to match the plasma and inner and outer vacuum solutions. The linear system can be ill-conditioned or even exactly singular, leading tomore » a dispersion relation with a discrete set of discontinuities. The coefficients for the analytic solution are calculated by solving the linear system with singular-value decomposition.« less

Unwrapping eddy current compensation: improved compensation of eddy current induced baseline shifts in high-resolution phase-contrast MRI at 9.4 Tesla.

PubMed

Espe, Emil K S; Zhang, Lili; Sjaastad, Ivar

2014-10-01

Phase-contrast MRI (PC-MRI) is a versatile tool allowing evaluation of in vivo motion, but is sensitive to eddy current induced phase offsets, causing errors in the measured velocities. In high-resolution PC-MRI, these offsets can be sufficiently large to cause wrapping in the baseline phase, rendering conventional eddy current compensation (ECC) inadequate. The purpose of this study was to develop an improved ECC technique (unwrapping ECC) able to handle baseline phase discontinuities. Baseline phase discontinuities are unwrapped by minimizing the spatiotemporal standard deviation of the static-tissue phase. Computer simulations were used for demonstrating the theoretical foundation of the proposed technique. The presence of baseline wrapping was confirmed in high-resolution myocardial PC-MRI of a normal rat heart at 9.4 Tesla (T), and the performance of unwrapping ECC was compared with conventional ECC. Areas of phase wrapping in static regions were clearly evident in high-resolution PC-MRI. The proposed technique successfully eliminated discontinuities in the baseline, and resulted in significantly better ECC than the conventional approach. We report the occurrence of baseline phase wrapping in PC-MRI, and provide an improved ECC technique capable of handling its presence. Unwrapping ECC offers improved correction of eddy current induced baseline shifts in high-resolution PC-MRI. Copyright © 2013 Wiley Periodicals, Inc.

Primary care providers’ perspectives on discontinuing prostate cancer screening

PubMed Central

Pollack, Craig E.; Platz, Elizabeth A.; Bhavsar, Nrupen A.; Noronha, Gary; Green, Gene E.; Chen, Sean; Carter, H. Ballentine

2012-01-01

Background Clinical guidelines recommend against routine prostate specific antigen (PSA) screening in older men and those with lower life expectancies. We examined providers’ decision-making regarding discontinuing PSA screening. Methods We administered a survey of primary providers from a large, university-affiliated primary care practice. Providers were asked about their current screening practices, factors that influence their decision to discontinue screening, and barriers to discontinuing screening. Bivariate and multivariable logistic regression analyses were used to examine whether taking age and/or life expectancy into account and barriers to discontinuing were associated with clinician characteristics and practice styles. Results 88.7% of providers participated in the survey (125 out of 141). Over half (59.3%) took both age and life expectancy into account whereas 12.2% did not consider either in their decisions to discontinue PSA screening. Providers varied with the age they typically stop screening and majority (66.4%) report difficulty in assessing life expectancy. Taking patient age and life expectancy into account was not associated with provider characteristics or practice styles. The most frequently cited barriers to discontinuing PSA screening were patient expectation (74.4%) and time constraints (66.4%). Black providers were significantly less likely than non-black providers to endorse barriers related to time constraints and clinical uncertainty, though these results are limited by the small sample size of black providers. Conclusion Though age and life expectancy often figure prominently in decisions to employ screening, providers face multiple barriers to discontinue PSA routine screening, PMID:22517310

75 FR 52627 - Disenrollment Procedures

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-27

... program that has been discontinued. It also amends the regulation to reflect current VA practice and to... conform with current VA practice, which does not disenroll veterans based on their failure to file VA Form 10-10EZ. Current practice is reflected in current paragraph (d)(3)(iv). Removing paragraph (d)(5)(iii...

Unusually Deep Bonin Earthquake (M7.9) of May 30, 2015 Suggests that Stagnant Slab Transforms into Penetration Stage

NASA Astrophysics Data System (ADS)

Obayashi, M.; Fukao, Y.; Yoshimitsu, J.

2015-12-01

A great shock occurred at an unusual depth of 678 km far away from the well-defined Wadati-Benioff zone of the Izu-Bonin arc (Fig.1). To the north of this region the slab is stagnant above the 660 km discontinuity and to the south it penetrates the discontinuity (Fig.2). Thus, the slab in this region can be viewed as in a transitional state from the stagnant to penetrating slab. Here, the steeply dipping part of the slab bends sharply to horizontal and the great shock happened at the lowest corner of this bending. The CMT indicates a pure normal faulting with the trench-normal near horizontal tensional axis and the near vertical compressional axis (Fig.1). We suggest that this mechanism reflects a transitional state of slab deformation from the bending-dominant mode to the penetration-dominant mode. The mechanism is consistent with either of these two two modes. We show that the mechanism is also consistent with the resultant stress field generated by many deep shocks occurring along the Wadati-Benioff zone. The calculated stress field changes rapidly along a trench-normal profile at a depth of 680 km and becomes similar to that generated by the great shock at points near the hypocenter (Fig.3). Thus, the stress field due to the Wadati-Benioff zone earthquakes works to enhance the occurrence of deep shocks of the type of the 2015 great shock, which represents slab deformation associated with the transition from stagnant to penetrating slab.

Starbursts in blue compact dwarf galaxies

NASA Technical Reports Server (NTRS)

Thuan, Trinh Xuan

1987-01-01

All the arguments for a bursting mode of star formation in blue compact dwarf galaxies (BCD) are summarized. It is shown that spectral synthesis of far-ultraviolet spectra of BCDs constitutes a powerful way to study the star formation history in these galaxies. BCD luminosity functions show jumps and discontinuities. These jumps act like fossil records of the star-forming bursts, aiding in the counting and dating of the bursts.

Pregnancy Outcomes Related to Mycophenolate Exposure in Female Kidney Transplant Recipients.

PubMed

King, R W; Baca, M J; Armenti, V T; Kaplan, B

2017-01-01

In 2012, the U.S. Food and Drug Administration issued guidelines advising kidney transplant recipients (KTRs) to discontinue mycophenolate (MPA) in preparation for pregnancy. Little is known about how this guidance has affected pregnancy and graft outcomes. The purpose of this retrospective cohort study was to investigate any association between the discontinuation of MPA and KTR pregnancy and graft outcomes. Data from the National Transplantation Pregnancy Registry included 382 cases in which KTRs managed on MPA became pregnant. Overall, 22 variables, including the time in which a KTR discontinued MPA, were assessed across four end points: miscarriages, birth defects, and 2- and 5-year postpartum graft loss. Birth defects and miscarriages were similar among KTRs who discontinued MPA >6 and <6 weeks prior to pregnancy and during the first trimester. In contrast, discontinuing MPA during the second trimester or later significantly increased the risk of miscarriages (odds ratio [OR] 9.35, 95% confidence interval [CI] 4.31-20.00, p < 0.001) and birth defects (OR 6.06, 95% CI 1.96-18.87, p = 0.002). Discontinuing MPA <6 weeks prior to pregnancy was associated with an increased risk of 5-year graft loss. For the fetus, there is value to discontinuing MPA anytime prior to the second trimester. Adhering to current guidelines does not negatively affect graft survival. © Copyright 2016 The American Society of Transplantation and the American Society of Transplant Surgeons.

Sliding mode disturbance observer-based control of a twin rotor MIMO system.

PubMed

Rashad, Ramy; El-Badawy, Ayman; Aboudonia, Ahmed

2017-07-01

This work proposes a robust tracking controller for a helicopter laboratory setup known as the twin rotor MIMO system (TRMS) using an integral sliding mode controller. To eliminate the discontinuity in the control signal, the controller is augmented by a sliding mode disturbance observer. The actuator dynamics is handled using a backstepping approach which is applicable due to the continuous chattering-free nature of the command signals generated using the disturbance observer based controller. To avoid the complexity of analytically differentiating the command signals, a first order sliding mode differentiator is used. Stability analysis of the closed loop system and the ultimate boundedness of the tracking error is proved using Lyapunov stability arguments. The proposed controller is validated by several simulation studies and is compared to other schemes in the literature. Experimental results using a hardware-in-the-loop system validate the robustness and effectiveness of the proposed controller. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Unexplained infertility: overall ongoing pregnancy rate and mode of conception.

PubMed

Brandes, M; Hamilton, C J C M; van der Steen, J O M; de Bruin, J P; Bots, R S G M; Nelen, W L D M; Kremer, J A M

2011-02-01

Unexplained infertility is one of the most common diagnoses in fertility care. The aim of this study was to evaluate the outcome of current fertility management in unexplained infertility. In an observational, longitudinal, multicentre cohort study, 437 couples were diagnosed with unexplained infertility and were available for analysis. They were treated according to their prognosis using standing national treatment protocols: (i) expectant management-IUI-IVF (main treatment route), (ii) IUI-IVF and (iii) directly IVF. Primary outcome measures were: ongoing pregnancy rate, patient flow over the strategies, numbers of protocol violation and drop out rates. A secondary outcome measure was the prediction of ongoing pregnancy and mode of conception. Of all couples 81.5% (356/437) achieved an ongoing pregnancy and 73.9% (263/356) of the pregnancies were conceived spontaneously. There were 408 couples (93.4%) in strategy-1, 21 (5.0%) in strategy-2 and 8 (1.8%) in strategy-3. In total, 33 (7.6%) couples entered the wrong strategy. There were 104 couples (23.8%) who discontinued fertility treatment prematurely: 26 on doctor's advice (with 4 still becoming pregnant) and 78 on their own initiative (with 33 still achieving a pregnancy). Predictors for overall pregnancy chance and mode of conception were duration of infertility, female age and obstetrical history. Overall success rate in couples with unexplained infertility is high. Most pregnancies are conceived spontaneously. We recommend that if the pregnancy prognosis is good, expectant management should be suggested. The prognosis criteria for treatment with IUI or IVF needs to be investigated in randomized controlled trials.

AED Strategy after Refractory Epilepsy Surgery.

PubMed

Zigouris, Andreas; Alexiou, George A; Themistocleous, Marios S; Voulgaris, Spyridon

2017-01-01

Post-epilepsy surgery antiepileptic drug discontinuation (AED) practices remain unclear and little evidence about the optimum timing exists. In the present study, we reviewed the types of surgery for epilepsy and their outcome. The current concepts for discontinuation of AED after surgery are presented and all contributing factors that should be taken into consideration are discussed. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Non Destructive Test Dye Penetrant and Ultrasonic on Welding SMAW Butt Joint with Acceptance Criteria ASME Standard

NASA Astrophysics Data System (ADS)

Endramawan, T.; Sifa, A.

2018-02-01

The purpose of this research is to know the type of discontinuity of SMAW welding result and to determine acceptance criteria based on American Society of Mechanical Engineer (ASME) standard. Material used is mild steel 98,71% Fe and 0,212% C with hardness 230 VHN with specimen diameter 20 cm and thickness 1.2 cm which is welded use SMAW butt joint with electrode for rooting LB 52U diameter 2.6 mm, current 70 Ampere and voltage 380 volt, filler used LB 5218 electrode diameter 3.2 mm with current 80 Ampere and 380 volt. The method used to analyze the welded with non destructive test dye penetrant (PT) method to see indication on the surface of the object and Ultrasonic (UT) to see indication on the sub and inner the surface of the object, the result is discontinuity recorded and analyzed and then the discontinuity is determine acceptance criteria based on the American Society of Mechanical Engineer (ASME) standards. The result show the discontinuity of porosity on the surface of the welded and inclusion on sub material used ultrasonic test, all indication on dye penetrant or ultrasonic test if there were rejected of result of welded that there must be gouging on part which rejected and then re-welding.

Study of flow over object problems by a nodal discontinuous Galerkin-lattice Boltzmann method

NASA Astrophysics Data System (ADS)

Wu, Jie; Shen, Meng; Liu, Chen

2018-04-01

The flow over object problems are studied by a nodal discontinuous Galerkin-lattice Boltzmann method (NDG-LBM) in this work. Different from the standard lattice Boltzmann method, the current method applies the nodal discontinuous Galerkin method into the streaming process in LBM to solve the resultant pure convection equation, in which the spatial discretization is completed on unstructured grids and the low-storage explicit Runge-Kutta scheme is used for time marching. The present method then overcomes the disadvantage of standard LBM for depending on the uniform meshes. Moreover, the collision process in the LBM is completed by using the multiple-relaxation-time scheme. After the validation of the NDG-LBM by simulating the lid-driven cavity flow, the simulations of flows over a fixed circular cylinder, a stationary airfoil and rotating-stationary cylinders are performed. Good agreement of present results with previous results is achieved, which indicates that the current NDG-LBM is accurate and effective for flow over object problems.

Evidence for a genetic discontinuity between Neandertals and 24,000-year-old anatomically modern Europeans.

PubMed

Caramelli, David; Lalueza-Fox, Carles; Vernesi, Cristiano; Lari, Martina; Casoli, Antonella; Mallegni, Francesco; Chiarelli, Brunetto; Dupanloup, Isabelle; Bertranpetit, Jaume; Barbujani, Guido; Bertorelle, Giorgio

2003-05-27

During the late Pleistocene, early anatomically modern humans coexisted in Europe with the anatomically archaic Neandertals for some thousand years. Under the recent variants of the multiregional model of human evolution, modern and archaic forms were different but related populations within a single evolving species, and both have contributed to the gene pool of current humans. Conversely, the Out-of-Africa model considers the transition between Neandertals and anatomically modern humans as the result of a demographic replacement, and hence it predicts a genetic discontinuity between them. Following the most stringent current standards for validation of ancient DNA sequences, we typed the mtDNA hypervariable region I of two anatomically modern Homo sapiens sapiens individuals of the Cro-Magnon type dated at about 23 and 25 thousand years ago. Here we show that the mtDNAs of these individuals fall well within the range of variation of today's humans, but differ sharply from the available sequences of the chronologically closer Neandertals. This discontinuity is difficult to reconcile with the hypothesis that both Neandertals and early anatomically modern humans contributed to the current European gene pool.

Power-Quality Improvement in PFC Bridgeless SEPIC-Fed BLDC Motor Drive

NASA Astrophysics Data System (ADS)

Singh, Bhim; Bist, Vashist

2013-06-01

This article presents a design of a power factor correction (PFC)-based brushless DC (BLDC) motor drive. The speed control of BLDC motor is achieved by controlling the DC link voltage of the voltage source inverter (VSI) feeding BLDC motor using a single voltage sensor. A front-end bridgeless single-ended primary inductance converter (SEPIC) is used for DC link voltage control and PFC operation. A bridgeless SEPIC is designed to operate in discontinuous inductor current mode (DICM) thus utilizing a simple control scheme of voltage follower. An electronic commutation of BLDC motor is used for VSI to operate in a low-frequency operation for reduced switching losses in the VSI. Moreover, a bridgeless topology offers less conduction losses due to absence of diode bridge rectifier for further increasing the efficiency. The proposed BLDC motor drive is designed to operate over a wide range of speed control with an improved power-quality at the AC mains under the recommended international power-quality standards such as IEC 61000-3-2.

The elusive character of discontinuous deep-water channels: New insights from Lucia Chica channel system, offshore California

USGS Publications Warehouse

Maier, K.L.; Fildani, A.; Paull, C.K.; Graham, S.A.; McHargue, T.R.; Caress, D.W.; McGann, M.

2011-01-01

New high-resolution autonomous underwater vehicle (AUV) seafloor images, with 1 m lateral resolution and 0.3 m vertical resolution, reveal unexpected seafloor rugosity and low-relief (<10 m), discontinuous conduits over ~70 km2. Continuous channel thalwegs were interpreted originally from lower-resolution images, but newly acquired AUV data indicate that a single sinuous channel fed a series of discontinuous lower-relief channels. These discontinuous channels were created by at least four avulsion events. Channel relief, defined as the height from the thalweg to the levee crest, controls avulsions and overall stratigraphic architecture of the depositional area. Flowstripped turbidity currents separated into and reactivated multiple channels to create a distributary pattern and developed discontinuous trains of cyclic scours and megaflutes, which may be erosional precursors to continuous channels. The diverse features now imaged in the Lucia Chica channel system (offshore California) are likely common in modern and ancient systems with similar overall morphologies, but have not been previously mapped with lower-resolution detection methods in any of these systems. ?? 2011 Geological Society of America.

A PCT algorithm for discontinuation of antibiotic therapy is a cost-effective way to reduce antibiotic exposure in adult intensive care patients with sepsis.

PubMed

Kip, Michelle M A; Kusters, Ron; IJzerman, Maarten J; Steuten, Lotte M G

2015-01-01

Procalcitonin (PCT) is a specific marker for differentiating bacterial from non-infective causes of inflammation. It can be used to guide initiation and duration of antibiotic therapy in intensive care unit (ICU) patients with suspected sepsis, and might reduce the duration of hospital stay. Limiting antibiotic treatment duration is highly important because antibiotic over-use may cause patient harm, prolonged hospital stay, and resistance development. Several systematic reviews show that a PCT algorithm for antibiotic discontinuation is safe, but upfront investment required for PCT remains an important barrier against implementation. The current study investigates to what extent this PCT algorithm is a cost-effective use of scarce healthcare resources in ICU patients with sepsis compared to current practice. A decision tree was developed to estimate the health economic consequences of the PCT algorithm for antibiotic discontinuation from a Dutch hospital perspective. Input data were obtained from a systematic literature review. When necessary, additional information was gathered from open interviews with clinical chemists and intensivists. The primary effectiveness measure is defined as the number of antibiotic days, and cost-effectiveness is expressed as incremental costs per antibiotic day avoided. The PCT algorithm for antibiotic discontinuation is expected to reduce hospital spending by circa € 3503 per patient, indicating savings of 9.2%. Savings are mainly due to reductions in length of hospital stay, number of blood cultures performed, and, importantly, days on antibiotic therapy. Probabilistic and one-way sensitivity analyses showed the model outcome to be robust against changes in model inputs. Proven safe, a PCT algorithm for antibiotic discontinuation is a cost-effective means of reducing antibiotic exposure in adult ICU patients with sepsis, compared to current practice. Additional resources required for PCT are more than offset by downstream cost savings. This finding is highly important given the aim of preventing widespread antibiotic resistance.

Relation between Pressure Balance Structures and Polar Plumes from Ulysses High Latitude Observations

NASA Technical Reports Server (NTRS)

Yamauchi, Yohei; Suess, Steven T.; Sakurai, Takashi

2002-01-01

Ulysses observations have shown that pressure balance structures (PBSs) are a common feature in high-latitude, fast solar wind near solar minimum. Previous studies of Ulysses/SWOOPS plasma data suggest these PBSs may be remnants of coronal polar plumes. Here we find support for this suggestion in an analysis of PBS magnetic structure. We used Ulysses magnetometer data and applied a minimum variance analysis to magnetic discontinuities in PBSs. We found that PBSs preferentially contain tangential discontinuities, as opposed to rotational discontinuities and to non-PBS regions in the solar wind. This suggests that PBSs contain structures like current sheets or plasmoids that may be associated with network activity at the base of plumes.

Relation Between Pressure Balance Structures and Polar Plumes from Ulysses High Latitude Observations

NASA Technical Reports Server (NTRS)

Yamauchi, Y.; Suess, Steven T.; Sakurai, T.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

Ulysses observations have shown that pressure balance structures (PBSs) are a common feature in high-latitude, fast solar wind near solar minimum. Previous studies of Ulysses/SWOOPS plasma data suggest these PBSs may be remnants of coronal polar plumes. Here we find support for this suggestion in an analysis of PBS magnetic structure. We used Ulysses magnetometer data and applied a minimum variance analysis to discontinuities. We found that PBSs preferentially contain tangential discontinuities, as opposed to rotational discontinuities and to non-PBS regions in the solar wind. This suggests that PBSs contain structures like current sheets or plasmoids that may be associated with network activity at the base of plumes.

Traveling waves in Hall-magnetohydrodynamics and the ion-acoustic shock structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hagstrom, George I.; Hameiri, Eliezer

Hall-magnetohydrodynamics (HMHD) is a mixed hyperbolic-parabolic partial differential equation that describes the dynamics of an ideal two fluid plasma with massless electrons. We study the only shock wave family that exists in this system (the other discontinuities being contact discontinuities and not shocks). We study planar traveling wave solutions and we find solutions with discontinuities in the hydrodynamic variables, which arise due to the presence of real characteristics in Hall-MHD. We introduce a small viscosity into the equations and use the method of matched asymptotic expansions to show that solutions with a discontinuity satisfying the Rankine-Hugoniot conditions and also anmore » entropy condition have continuous shock structures. The lowest order inner equations reduce to the compressible Navier-Stokes equations, plus an equation which implies the constancy of the magnetic field inside the shock structure. We are able to show that the current is discontinuous across the shock, even as the magnetic field is continuous, and that the lowest order outer equations, which are the equations for traveling waves in inviscid Hall-MHD, are exactly integrable. We show that the inner and outer solutions match, which allows us to construct a family of uniformly valid continuous composite solutions that become discontinuous when the diffusivity vanishes.« less

Electromagnetic radiation in a semi-compact space

NASA Astrophysics Data System (ADS)

Iso, Satoshi; Kitazawa, Noriaki; Yokoo, Sumito

2018-02-01

In this note, we investigate the electromagnetic radiation emitted from a revolving point charge in a compact space. If the point charge is circulating with an angular frequency ω0 on the (x , y)-plane at z = 0 with boundary conditions, x ∼ x + 2 πR and y ∼ y + 2 πR, it emits radiation into the z-direction of z ∈ [ - ∞ , + ∞ ]. We find that the radiation shows discontinuities as a function of ω0 R at which a new propagating mode with a different Fourier component appears. For a small radius limit ω0 R ≪ 1, all the Fourier modes except the zero mode on (x , y)-plane are killed, but an effect of squeezing the electric field totally enhances the radiation. In the large volume limit ω0 R → ∞, the energy flux of the radiation reduces to the expected Larmor formula.

Bending light via adiabatic optical transition in longitudinally modulated photonic lattices

PubMed Central

Han, Bin; Xu, Lei; Dou, Yiling; Xu, Jingjun; Zhang, Guoquan

2015-01-01

Bending light in a controllable way is desired in various applications such as beam steering, navigating and cloaking. Different from the conventional way to bend light by refractive index gradient, transformation optics or special beams through wavefront design such as Airy beams and surface plasmons, we proposed a mechanism to bend light via resonant adiabatic optical transition between Floquet-Bloch (FB) modes from different FB bands in longitudinally modulated photonic lattices. The band structure of longitudinally modulated photonic lattices was calculated by employing the concept of quasi-energy based on the Floquet-Bloch theory, showing the existence of band discontinuities at specific resonant points which cannot be revealed by the coupled-mode theory. Interestingly, different FB bands can be seamlessly connected at these resonant points in longitudinally modulated photonic lattices driven by adiabatically varying the longitudinal modulation period along the propagation direction, which stimulates the adiabatic FB mode transition between different FB bands. PMID:26511890

Why 4-H Members Leave: A Study of Discontinuance through Both Current 4-H Members and Former Members

ERIC Educational Resources Information Center

Chilek, Kevin Dwayne

2012-01-01

4-H members quit. It is part of every 4-H program, and according to the research, it is even part of growing up. If only we knew why they quit, we could possibly do something about it. To date, the reasons youth join 4-H have been more thoroughly researched than the reasons they quit. This study explores why youth choose to discontinue membership…

Invariant Clustering Using Scattering Matrices.

DTIC Science & Technology

1983-02-23

general three-dimensional elasticity a discontinuous fiber, however. equations for an anisotropic beam have been used by Sayir [19] to show that shear...34 Exptl. tives for Viscoelastic Constitutive Equations " Tech.,6(2), pp 10-14 (Apr 1982). (Submitted to J. Rheology, Apr 1982). 63. Gibson, R.F., Yau, A...vibration modes up to about nine nodes [4], Added mass of water. The frequency range relevant In the Timoshenko beam equations governing free, for ship

Discontinuous Galerkin modeling of the Columbia River's coupled estuary-plume dynamics

NASA Astrophysics Data System (ADS)

Vallaeys, Valentin; Kärnä, Tuomas; Delandmeter, Philippe; Lambrechts, Jonathan; Baptista, António M.; Deleersnijder, Eric; Hanert, Emmanuel

2018-04-01

The Columbia River (CR) estuary is characterized by high river discharge and strong tides that generate high velocity flows and sharp density gradients. Its dynamics strongly affects the coastal ocean circulation. Tidal straining in turn modulates the stratification in the estuary. Simulating the hydrodynamics of the CR estuary and plume therefore requires a multi-scale model as both shelf and estuarine circulations are coupled. Such a model has to keep numerical dissipation as low as possible in order to correctly represent the plume propagation and the salinity intrusion in the estuary. Here, we show that the 3D baroclinic discontinuous Galerkin finite element model SLIM 3D is able to reproduce the main features of the CR estuary-to-ocean continuum. We introduce new vertical discretization and mode splitting that allow us to model a region characterized by complex bathymetry and sharp density and velocity gradients. Our model takes into account the major forcings, i.e. tides, surface wind stress and river discharge, on a single multi-scale grid. The simulation period covers the end of spring-early summer of 2006, a period of high river flow and strong changes in the wind regime. SLIM 3D is validated with in-situ data on the shelf and at multiple locations in the estuary and compared with an operational implementation of SELFE. The model skill in the estuary and on the shelf indicate that SLIM 3D is able to reproduce the key processes driving the river plume dynamics, such as the occurrence of bidirectional plumes or reversals of the inner shelf coastal currents.

Low-Temperature Criticality of Martensitic Transformations of Cu Nanoprecipitates in α-Fe

NASA Astrophysics Data System (ADS)

Erhart, Paul; Sadigh, Babak

2013-07-01

Nanoprecipitates form during nucleation of multiphase equilibria in phase segregating multicomponent systems. In spite of their ubiquity, their size-dependent physical chemistry, in particular, at the boundary between phases with incompatible topologies, is still rather arcane. Here, we use extensive atomistic simulations to map out the size-temperature phase diagram of Cu nanoprecipitates in α-Fe. The growing precipitates undergo martensitic transformations from the body-centered cubic (bcc) phase to multiply twinned 9R structures. At high temperatures, the transitions exhibit strong first-order character and prominent hysteresis. Upon cooling, the discontinuities become less pronounced and the transitions occur at ever smaller cluster sizes. Below 300 K, the hysteresis vanishes while the transition remains discontinuous with a finite but diminishing latent heat. This unusual size-temperature phase diagram results from the entropy generated by the soft modes of the bcc-Cu phase, which are stabilized through confinement by the α-Fe lattice.

Forensic Excavation of Rock Masses: A Technique to Investigate Discontinuity Persistence

NASA Astrophysics Data System (ADS)

Shang, J.; Hencher, S. R.; West, L. J.; Handley, K.

2017-11-01

True persistence of rock discontinuities (areas with insignificant tensile strength) is an important factor controlling the engineering behaviour of fractured rock masses, but is extremely difficult to quantify using current geological survey methodologies, even where there is good rock exposure. Trace length as measured in the field or using remote measurement devices is actually only broadly indicative of persistence for rock engineering practice and numerical modelling. Visible traces of discontinuities are treated as if they were open fractures within rock mass classifications, despite many such traces being non-persistent and actually retaining considerable strength. The common assumption of 100% persistence, based on trace length, is generally extremely conservative in terms of strength and stiffness, but not always so and may lead to a wrong prediction of failure mechanism or of excavatability. Assuming full persistence would give hopelessly incorrect predictions of hydraulic conductivity. A new technique termed forensic excavation of rock masses is introduced, as a procedure for directly investigating discontinuity persistence. This technique involves non-explosive excavation of rock masses by injecting an expansive chemical splitter along incipient discontinuities. On expansion, the splitter causes the incipient traces to open as true joints. Experiments are described in which near-planar rock discontinuities, through siltstone and sandstone, were opened up by injecting the splitter into holes drilled along the lines of visible traces of the discontinuities in the laboratory and in the field. Once exposed the surfaces were examined to investigate the pre-existing persistence characteristics of the incipient discontinuities. One conclusion from this study is that visible trace length of a discontinuity can be a poor indicator of true persistence (defined for a fracture area with negligible tensile strength). An observation from this series of experiments was that freshly failed surfaces through pre-existing rock bridges were relatively rough compared to sections of pre-existing weaker areas of geologically developed (though still incipient) discontinuities. Fractographic features such as hackle and rib marks were typical of the freshly broken rock bridges, whereas opened-up areas of incipient discontinuity were smoother. Schmidt hammer rebound values were generally higher for the rock bridge areas, probably reflecting their lower degree of chemical and physical weathering.

Buck-boost converter for simultaneous semi-active vibration control and energy harvesting for electromagnetic regenerative shock absorber

NASA Astrophysics Data System (ADS)

Li, Peng; Zhang, Chongxiao; Kim, Junyoung; Yu, Liangyao; Zuo, Lei

2014-04-01

Regenerative semi-active suspensions can capture the previously dissipated vibration energy and convert it to usable electrical energy for powering on-board electronic devices, while achieve both the better ride comfort and improved road handling performance at the same time when certain control is applied. To achieve this objective, the power electronics interface circuit connecting the energy harvester and the electrical loads, which can perform simultaneous vibration control and energy harvesting function is in need. This paper utilized a buck-boost converter for simultaneous semi-active vibration control and energy harvesting with electromagnetic regenerative shock absorber, which utilizes a rotational generator to converter the vibration energy to electricity. It has been found that when the circuit works in discontinuous current mode (DCM), the ratio between the input voltage and current is only related to the duty cycle of the switch pulse width modulation signal. Using this property, the buck-boost converter can be used to perform semi-active vibration control by controlling the load connected between the terminals of the generator in the electromagnetic shock absorber. While performing the vibration control, the circuit always draw current from the shock absorber and the suspension remain dissipative, and the shock absorber takes no additional energy to perform the vibration control. The working principle and dynamics of the circuit has been analyzed and simulations were performed to validate the concept.

An improved switching converter model. Ph.D. Thesis. Final Report

NASA Technical Reports Server (NTRS)

Shortt, D. J.

1982-01-01

The nonlinear modeling and analysis of dc-dc converters in the continuous mode and discontinuous mode was done by averaging and discrete sampling techniques. A model was developed by combining these two techniques. This model, the discrete average model, accurately predicts the envelope of the output voltage and is easy to implement in circuit and state variable forms. The proposed model is shown to be dependent on the type of duty cycle control. The proper selection of the power stage model, between average and discrete average, is largely a function of the error processor in the feedback loop. The accuracy of the measurement data taken by a conventional technique is affected by the conditions at which the data is collected.

Effectiveness of Anti-Dementia Drugs in Extremely Severe Alzheimer's Disease: A 12-Week, Multicenter, Randomized, Single-Blind Study.

PubMed

Hong, Yun Jeong; Choi, Seong Hye; Jeong, Jee Hyang; Park, Kyung Won; Na, Hae Ri

2018-01-01

There is insufficient evidence to guide decisions concerning how long anti-dementia drug (ADD) regimens should be maintained in severe Alzheimer's disease (AD). We investigated whether patients with extremely severe AD who were already receiving donepezil or memantine benefited from continuing treatment. In this randomized and rater-blinded trial, 65 AD patients with a Mini-Mental State Examination score from 0 to 5 and a score of 6c or worse on Functional Assessment Staging were randomly assigned to an ADD-continuation group (N = 30) or an ADD-discontinuation group (N = 35). The current use of donepezil or memantine was maintained for 12 weeks in the ADD-continuation group and was discontinued after baseline in the ADD-discontinuation group. Efficacy measures were obtained at baseline and 12 weeks. The primary efficacy variable was the change from baseline to the end of the study in Baylor Profound Mental State Examination (BPMSE) scores. The change in the BPMSE from baseline to the end of the study in the ADD-continuation group (a 0.4-point improvement) was not equivalent to that in the ADD-discontinuation group (a 0.5-point decline), as determined by two one-sided tests of equivalence. Study withdrawals due to adverse events (11.4% versus 6.7%) were more frequent in the ADD-discontinuation group than in the ADD-continuation group. Continued treatment with donepezil or memantine seems unequal and might be superior to withdrawal of the drugs in terms of the effects on global cognition in patients with extremely severe AD. Current Controlled Trials number: KCT0000874 (CRIS).

Nonadiabatic nonradial p-mode frequencies of the standard solar model, with and without helium diffusion

NASA Technical Reports Server (NTRS)

Guenther, D. B.

1994-01-01

The nonadiabatic frequencies of a standard solar model and a solar model that includes helium diffusion are discussed. The nonadiabatic pulsation calculation includes physics that describes the losses and gains due to radiation. Radiative gains and losses are modeled in both the diffusion approximation, which is only valid in optically thick regions, and the Eddington approximation, which is valid in both optically thin and thick regions. The calculated pulsation frequencies for modes with l less than or equal to 1320 are compared to the observed spectrum of the Sun. Compared to a strictly adiabatic calculation, the nonadiabatic calculation of p-mode frequencies improves the agreement between model and observation. When helium diffusion is included in the model the frequencies of the modes that are sensitive to regions near the base of the convection zone are improved (i.e., brought into closer agreement with observation), but the agreement is made worse for other modes. Cyclic variations in the frequency spacings of the Sun as a function of frequency of n are presented as evidence for a discontinuity in the structure of the Sun, possibly located near the base of the convection zone.

Plasmonic modes in nanowire dimers: A study based on the hydrodynamic Drude model including nonlocal and nonlinear effects

NASA Astrophysics Data System (ADS)

Moeferdt, Matthias; Kiel, Thomas; Sproll, Tobias; Intravaia, Francesco; Busch, Kurt

2018-02-01

A combined analytical and numerical study of the modes in two distinct plasmonic nanowire systems is presented. The computations are based on a discontinuous Galerkin time-domain approach, and a fully nonlinear and nonlocal hydrodynamic Drude model for the metal is utilized. In the linear regime, these computations demonstrate the strong influence of nonlocality on the field distributions as well as on the scattering and absorption spectra. Based on these results, second-harmonic-generation efficiencies are computed over a frequency range that covers all relevant modes of the linear spectra. In order to interpret the physical mechanisms that lead to corresponding field distributions, the associated linear quasielectrostatic problem is solved analytically via conformal transformation techniques. This provides an intuitive classification of the linear excitations of the systems that is then applied to the full Maxwell case. Based on this classification, group theory facilitates the determination of the selection rules for the efficient excitation of modes in both the linear and nonlinear regimes. This leads to significantly enhanced second-harmonic generation via judiciously exploiting the system symmetries. These results regarding the mode structure and second-harmonic generation are of direct relevance to other nanoantenna systems.

An updated Lagrangian discontinuous Galerkin hydrodynamic method for gas dynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Tong; Shashkov, Mikhail Jurievich; Morgan, Nathaniel Ray

Here, we present a new Lagrangian discontinuous Galerkin (DG) hydrodynamic method for gas dynamics. The new method evolves conserved unknowns in the current configuration, which obviates the Jacobi matrix that maps the element in a reference coordinate system or the initial coordinate system to the current configuration. The density, momentum, and total energy (ρ, ρu, E) are approximated with conservative higher-order Taylor expansions over the element and are limited toward a piecewise constant field near discontinuities using a limiter. Two new limiting methods are presented for enforcing the bounds on the primitive variables of density, velocity, and specific internal energymore » (ρ, u, e). The nodal velocity, and the corresponding forces, are calculated by solving an approximate Riemann problem at the element nodes. An explicit second-order method is used to temporally advance the solution. This new Lagrangian DG hydrodynamic method conserves mass, momentum, and total energy. 1D Cartesian coordinates test problem results are presented to demonstrate the accuracy and convergence order of the new DG method with the new limiters.« less

Effect of Discontinuities and Penetrations on the Shielding Efficacy of High Temperature Superconducting Magnetic Shields

NASA Astrophysics Data System (ADS)

Hatwar, R.; Kvitkovic, J.; Herman, C.; Pamidi, S.

2015-12-01

High Temperature Superconducting (HTS) materials have been demonstrated to be suitable for applications in shielding of both DC and AC magnetic fields. Magnetic shielding is required for protecting sensitive instrumentation from external magnetic fields and for preventing the stray magnetic fields produced by high power density equipment from affecting neighbouring devices. HTS shields have high current densities at relatively high operating temperatures (40-77 K) and can be easily fabricated using commercial HTS conductor. High current densities in HTS materials allow design and fabrication of magnetic shields that are lighter and can be incorporated into the body and skin of high power density devices. HTS shields are particularly attractive for HTS devices because a single cryogenic system can be used for cooling the device and the associated shield. Typical power devices need penetrations for power and signal cabling and the penetrations create discontinuities in HTS shields. Hence it is important to assess the effect of the necessary discontinuities on the efficacy of the shields and the design modifications necessary to accommodate the penetrations.

An updated Lagrangian discontinuous Galerkin hydrodynamic method for gas dynamics

DOE PAGES

Wu, Tong; Shashkov, Mikhail Jurievich; Morgan, Nathaniel Ray; ...

2018-04-09

Here, we present a new Lagrangian discontinuous Galerkin (DG) hydrodynamic method for gas dynamics. The new method evolves conserved unknowns in the current configuration, which obviates the Jacobi matrix that maps the element in a reference coordinate system or the initial coordinate system to the current configuration. The density, momentum, and total energy (ρ, ρu, E) are approximated with conservative higher-order Taylor expansions over the element and are limited toward a piecewise constant field near discontinuities using a limiter. Two new limiting methods are presented for enforcing the bounds on the primitive variables of density, velocity, and specific internal energymore » (ρ, u, e). The nodal velocity, and the corresponding forces, are calculated by solving an approximate Riemann problem at the element nodes. An explicit second-order method is used to temporally advance the solution. This new Lagrangian DG hydrodynamic method conserves mass, momentum, and total energy. 1D Cartesian coordinates test problem results are presented to demonstrate the accuracy and convergence order of the new DG method with the new limiters.« less

Admissible Shape Parameters for a Planar Quasi-Static Constraint Mode Tire Model

DTIC Science & Technology

2014-01-21

Journal of Vibration, 1988. 110(1): p. 70-75. 4. Zegelaar, P.W.A.P., H. B., The In-plane Dynamics of Tyres on Uneven Roads . Vehicle System Dynamics...ADDRESS(ES) Vehicle Terrain performance laboratory,Virginia Tech Mechanical Engineering Department,635 Prices Fork Road - MC 0238,Blacksburg,VA,24061...such that the upper portion is in direct contact with the lower portion and there is a discontinuous and dramatic increase in apparent stiffness). A

A Wavelet-based Fast Discrimination of Transformer Magnetizing Inrush Current

NASA Astrophysics Data System (ADS)

Kitayama, Masashi

Recently customers who need electricity of higher quality have been installing co-generation facilities. They can avoid voltage sags and other distribution system related disturbances by supplying electricity to important load from their generators. For another example, FRIENDS, highly reliable distribution system using semiconductor switches or storage devices based on power electronics technology, is proposed. These examples illustrates that the request for high reliability in distribution system is increasing. In order to realize these systems, fast relaying algorithms are indispensable. The author proposes a new method of detecting magnetizing inrush current using discrete wavelet transform (DWT). DWT provides the function of detecting discontinuity of current waveform. Inrush current occurs when transformer core becomes saturated. The proposed method detects spikes of DWT components derived from the discontinuity of the current waveform at both the beginning and the end of inrush current. Wavelet thresholding, one of the wavelet-based statistical modeling, was applied to detect the DWT component spikes. The proposed method is verified using experimental data using single-phase transformer and the proposed method is proved to be effective.

The role of routine polio immunization in the post-certification era.

PubMed Central

Sutter, Roland W.; Cáceres, Victor M.; Mas Lago, Pedro

2004-01-01

The role of routine vaccination against poliomyelitis for the post-certification era remains an important area for policy decision-making. Two critical decisions need to be taken: first, to continue or discontinue vaccination with the live attenuated oral poliovirus vaccine (OPV); and second, if OPV is to be discontinued, whether vaccination with inactivated poliovirus vaccine (IPV) is needed. Four potential vaccination scenarios can be constructed: stop all polio vaccination; continue with current vaccination policies (OPV, IPV, or sequential schedule); discontinue OPV, but continue IPV universally; or discontinue OPV, but continue IPV in selected countries. All possible scenarios require continued investments in a surveillance and response strategy, including a stockpile of polio vaccine. Continuing vaccination would limit the savings that could be applied to the control of other health priorities. This report reviews the key issues associated with each scenario, highlights the advantages and disadvantages of each scenario, and outlines the major challenges for policy decision-making. PMID:15106298

Investigation of smoothness-increasing accuracy-conserving filters for improving streamline integration through discontinuous fields.

PubMed

Steffen, Michael; Curtis, Sean; Kirby, Robert M; Ryan, Jennifer K

2008-01-01

Streamline integration of fields produced by computational fluid mechanics simulations is a commonly used tool for the investigation and analysis of fluid flow phenomena. Integration is often accomplished through the application of ordinary differential equation (ODE) integrators--integrators whose error characteristics are predicated on the smoothness of the field through which the streamline is being integrated--smoothness which is not available at the inter-element level of finite volume and finite element data. Adaptive error control techniques are often used to ameliorate the challenge posed by inter-element discontinuities. As the root of the difficulties is the discontinuous nature of the data, we present a complementary approach of applying smoothness-enhancing accuracy-conserving filters to the data prior to streamline integration. We investigate whether such an approach applied to uniform quadrilateral discontinuous Galerkin (high-order finite volume) data can be used to augment current adaptive error control approaches. We discuss and demonstrate through numerical example the computational trade-offs exhibited when one applies such a strategy.

The Interaction of Solar wind Discontinuities with the Earth's Bow Shock

NASA Technical Reports Server (NTRS)

Sibeck, David G.

2000-01-01

Funding from NASA Grant No. NAG54679 was received in three installments. The first year's installment amounted to only one month of salary support and was used to prepare survey plots. The second year's installment allowed us to complete two research papers concerning the interaction of solar wind discontinuities with the Earth's bow shock. In the first (published) paper, we reported that the discontinuities launch slow mode waves into the magnetosheath and the slow mode waves always propagate antisunward through the flank magnetosheath. Because the sunward/antisunward sense of the magnetosheath magnetic field reverses across local noon, so does the (north/south or east/west) sense of the velocity fluctuations associated with the waves. Wind, Geotail, and IMP-8 observations were used for this study. In the second study, we used Wind and Interball-1 observations to demonstrate that pressure pulses in the magnetosheath occur in pairs and that they bound pressure cavities and/or brief intervals of outward magnetopause motion. This paper is now in press. Funding from the third year's installment has been used to investigate the two aspects of the foreshock. Two manuscripts are now in preparation for submission to the Journal of Geophysical Research. The first reports that waves within the foreshock account for many instances of poor correlations between two solar wind monitors. Remaining cases of poor correlation occur during intervals of nearly constant IMF orientations and magnetic field strengths. While the former category pose a significant difficulty for space weather forecasts, the latter do not. The second study surveys IMP-8 observations of the foreshock. We find that diamagnetic cavities are common, particularly during periods of high solar wind velocity and low solar wind density. Plasma densities, temperatures, and magnetic field strengths fall during intervals of enhanced energetic particle fluxes. The cavities are bounded by regions of decelerated solar wind plasma and enhanced densities and magnetic field strengths.

Overmoded subterahertz surface wave oscillator with pure TM{sub 01} mode output

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Guangqiang; Zeng, Peng; Wang, Dongyang

2016-02-15

Overmoded O-type Cerenkov generators using annular electron beams are facing the problem of multi-modes output due to the inevitable structural discontinuities. A simple but effective method to achieve the pure TM{sub 01} mode output is applied on the 0.14 THz overmoded surface wave oscillator (SWO) in this paper. In spite of still using an overmoded slow wave structure to ensure the easy fabrication, the followed smooth circular waveguide is shrinkingly tapered to the output waveguide with appropriate radius that it cuts off other higher modes except TM{sub 01} mode. Moreover, the modified device here has the same power capacity as themore » previous one according to the numerical analysis. By optimized lengths of the transition waveguide and tapered waveguide, particle-in-cell simulation results indicate that the subterahertz wave with output power increased 14.2% at the same frequency is obtained from the proposed SWO under the previous input conditions, and importantly, the output power is all carried by TM{sub 01} mode as expected. Further simulation results in the pulse regime confirm the feasibility of the optimized structure in the actual experiments. This simple and viable design is also applicable to overmoded devices in the lower frequency band of subterahertz wave.« less

Effect of Pulse and dc Formation on the Performance of One-Transistor and One-Resistor Resistance Random Access Memory Devices

NASA Astrophysics Data System (ADS)

Liu, Hong-Tao; Yang, Bao-He; Lv, Hang-Bing; Xu, Xiao-Xin; Luo, Qing; Wang, Guo-Ming; Zhang, Mei-Yun; Long, Shi-Bing; Liu, Qi; Liu, Ming

2015-02-01

We investigate the effect of the formation process under pulse and dc modes on the performance of one transistor and one resistor (1T1R) resistance random access memory (RRAM) device. All the devices are operated under the same test conditions, except for the initial formation process with different modes. Based on the statistical results, the high resistance state (HRS) under the dc forming mode shows a lower value with better distribution compared with that under the pulse mode. One of the possible reasons for such a phenomenon originates from different properties of conductive filament (CF) formed in the resistive switching layer under two different modes. For the dc forming mode, the formed filament is thought to be continuous, which is hard to be ruptured, resulting in a lower HRS. However, in the case of pulse forming, the filament is discontinuous where the transport mechanism is governed by hopping. The low resistance state (LRS) can be easily changed by removing a few trapping states from the conducting path. Hence, a higher HRS is thus observed. However, the HRS resistance is highly dependent on the length of the gap opened. A slight variation of the gap length will cause wide dispersion of resistance.

76 FR 68166 - Discontinuing the Mass Mailing of Paper Fee Schedules to Registered Attorneys, Agents, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-03

... current fee schedule is essentially built into the on-line systems (e.g., EFS-Web, TEAS, accessible... applications are filed on-line via TEAS. The official, current USPTO fee schedule will continue to be available...

Geometrically Nonlinear Field Fracture Mechanics and Crack Nucleation, Application to Strain Localization Fields in Al-Cu-Li Aerospace Alloys.

PubMed

Gupta, Satyapriya; Taupin, Vincent; Fressengeas, Claude; Jrad, Mohamad

2018-03-27

The displacement discontinuity arising between crack surfaces is assigned to smooth densities of crystal defects referred to as disconnections, through the incompatibility of the distortion tensor. In a dual way, the disconnections are defined as line defects terminating surfaces where the displacement encounters a discontinuity. A conservation statement for the crack opening displacement provides a framework for disconnection dynamics in the form of transport laws. A similar methodology applied to the discontinuity of the plastic displacement due to dislocations results in the concurrent involvement of dislocation densities in the analysis. Non-linearity of the geometrical setting is assumed for defining the elastic distortion incompatibility in the presence of both dislocations and disconnections, as well as for their transport. Crack nucleation in the presence of thermally-activated fluctuations of the atomic order is shown to derive from this nonlinearity in elastic brittle materials, without any algorithmic rule or ad hoc material parameter. Digital image correlation techniques applied to the analysis of tensile tests on ductile Al-Cu-Li samples further demonstrate the ability of the disconnection density concept to capture crack nucleation and relate strain localization bands to consistent disconnection fields and to the eventual occurrence of complex and combined crack modes in these alloys.

Numerical simulation and experimental validation of Lamb wave propagation behavior in composite plates

NASA Astrophysics Data System (ADS)

Kim, Sungwon; Uprety, Bibhisha; Mathews, V. John; Adams, Daniel O.

2015-03-01

Structural Health Monitoring (SHM) based on Acoustic Emission (AE) is dependent on both the sensors to detect an impact event as well as an algorithm to determine the impact location. The propagation of Lamb waves produced by an impact event in thin composite structures is affected by several unique aspects including material anisotropy, ply orientations, and geometric discontinuities within the structure. The development of accurate numerical models of Lamb wave propagation has important benefits towards the development of AE-based SHM systems for impact location estimation. Currently, many impact location algorithms utilize the time of arrival or velocities of Lamb waves. Therefore the numerical prediction of characteristic wave velocities is of great interest. Additionally, the propagation of the initial symmetric (S0) and asymmetric (A0) wave modes is important, as these wave modes are used for time of arrival estimation. In this investigation, finite element analyses were performed to investigate aspects of Lamb wave propagation in composite plates with active signal excitation. A comparative evaluation of two three-dimensional modeling approaches was performed, with emphasis placed on the propagation and velocity of both the S0 and A0 wave modes. Results from numerical simulations are compared to experimental results obtained from active AE testing. Of particular interest is the directional dependence of Lamb waves in quasi-isotropic carbon/epoxy composite plates. Numerical and experimental results suggest that although a quasi-isotropic composite plate may have the same effective elastic modulus in all in-plane directions, the Lamb wave velocity may have some directional dependence. Further numerical analyses were performed to investigate Lamb wave propagation associated with circular cutouts in composite plates.

Healthcare Resource Waste Associated with Patient Nonadherence and Early Discontinuation of Traditional Continuous Glucose Monitoring in Real-World Settings: A Multicountry Analysis.

PubMed

Yu, Shengsheng; Varughese, Biju; Li, Zhiyi; Kushner, Pam R

2018-06-01

Traditional continuous glucose monitoring (CGM) provides detailed information on glucose patterns and trends to inform daily diabetes management decisions, which is particularly beneficial for patients with a history of hypoglycemia unawareness. However, a high level of patient adherence (≥70%) is required to achieve clinical benefits. The aim of this study was to assess the impact of real-world patient nonadherence and early discontinuation on healthcare resource use. A cost calculator was designed to evaluate monthly healthcare resource waste within the first year of traditional CGM initiation by combining estimates of real-world nonadherence and early discontinuation from the literature with the wholesale acquisition costs of the current technology in the United States (for a commercial payer and for Medicare), or its equivalent in Sweden, Germany, or the Netherlands. Based on an early discontinuation rate of 27% and nonadherence rates of 13.9%-31.1% over the 12 months following initiation, the healthcare resource waste associated with nonadherence and early discontinuation was $220,289 and $21,775, respectively, for every 100 patients initiating CGM in the U.S. commercial payer scenario. In the Medicare scenario, the corresponding figures were $72,648 and $5,675, respectively. In both scenarios, nonadherence and early discontinuation accounted for ∼24% of resources being wasted within the first year of CGM initiation. Similar results were observed using the local costs in the other countries analyzed. The healthcare resource waste associated with traditional CGM nonadherence and early discontinuation warrants deliberate consideration when selecting suitable patients for this technology.

Jet behaviors and ejection mode recognition of electrohydrodynamic direct-write

NASA Astrophysics Data System (ADS)

Zheng, Jianyi; Zhang, Kai; Jiang, Jiaxin; Wang, Xiang; Li, Wenwang; Liu, Yifang; Liu, Juan; Zheng, Gaofeng

2018-01-01

By introducing image recognition and micro-current testing, jet behavior research was conducted, in which the real-time recognition of ejection mode was realized. To study the factors influencing ejection modes and the current variation trends under different modes, an Electrohydrodynamic Direct-Write (EDW) system with functions of current detection and ejection mode recognition was firstly built. Then a program was developed to recognize the jet modes. As the voltage applied to the metal tip increased, four jet ejection modes in EDW occurred: droplet ejection mode, Taylor cone ejection mode, retractive ejection mode and forked ejection mode. In this work, the corresponding relationship between the ejection modes and the effect on fiber deposition as well as current was studied. The real-time identification of ejection mode and detection of electrospinning current was realized. The results in this paper are contributed to enhancing the ejection stability, providing a good technical basis to produce continuous uniform nanofibers controllably.

Forensic analysis of rockfall scars

NASA Astrophysics Data System (ADS)

de Vilder, Saskia J.; Rosser, Nick J.; Brain, Matthew J.

2017-10-01

We characterise and analyse the detachment (scar) surfaces of rockfalls to understand the mechanisms that underpin their failure. Rockfall scars are variously weathered and comprised of both discontinuity release surfaces and surfaces indicative of fracturing through zones of previously intact rock, known as rock bridges. The presence of rock bridges and pre-existing discontinuities is challenging to quantify due to the difficulty in determining discontinuity persistence below the surface of a rock slope. Rock bridges form an important control in holding blocks onto rockslopes, with their frequency, extent and location commonly modelled from the surface exposure of daylighting discontinuities. We explore an alternative approach to assessing their role, by characterising failure scars. We analyse a database of multiple rockfall scar surfaces detailing the areal extent, shape, and location of broken rock bridges and weathered surfaces. Terrestrial laser scanning and gigapixel imagery were combined to record the detailed texture and surface morphology. From this, scar surfaces were mapped via automated classification based on RGB pixel values. Our analysis of the resulting data from scars on the North Yorkshire coast (UK) indicates a wide variation in both weathering and rock bridge properties, controlled by lithology and associated rock mass structure. Importantly, the proportion of rock bridges in a rockfall failure surface does not increase with failure size. Rather larger failures display fracturing through multiple rock bridges, and in contrast smaller failures fracture occurs only through a single critical rock bridge. This holds implications for how failure mechanisms change with rockfall size and shape. Additionally, the location of rock bridges with respect to the geometry of an incipient rockfall is shown to determine failure mode. Weathering can occur both along discontinuity surfaces and previously broken rock bridges, indicating the sequential stages of progressively detaching rockfall. Our findings have wider implications for hazard assessment where rock slope stability is dependent on the nature of rock bridges, how this is accounted for in slope stability modelling, and the implications of rock bridges on long-term rock slope evolution.

Discontinuity surfaces in the Lower Cretaceous of the high Andes (Mendoza, Argentina): Trace fossils and environmental implications

NASA Astrophysics Data System (ADS)

Mangano, M. G.; Buatois, L. A.

The paleoecologic and paleoenvironmental significance of trace fossils related to discontinuity surfaces in the Lower Cretaceous marine deposits of the Aconcagua area are analysed here. Carbonate-evaporite shoaling-upward cycles, developed by high organic production in a shallow hypersaline restricted environment, make up the section. Two types of cycles are defined, being mainly distinguished by their subtidal unit. Cycle I begins with a highly dolomitized lower subtidal unit (Facies A), followed upward by an intensely bioturbated upper subtidal unit (Facies B). The nodular packstone facies (B 1) is capped by a discontinuity surface (firmground or hardground) and occasionally overlain by an oystreid bed (Facies C). Cycle II is characterized by a pelletoidal subtidal unit (Facies B 2) with an abnormal salinity impoverished fauna. Both cycles end with intertidal to supratidal evaporite deposits (Facies D and E, respectively). Attention is particularly focused on cycle I due to its ichologic content. The mode of preservation and the distribution of trace fossils in nodular packstone facies are controlled by original substrate consolidation. Thalassinoides paradoxicus (pre-omission suite) represents colonization in a soft bottom, while Thalassinoides suevicus (omission suite pre-lithification) is apparently restricted to firm substrates. When consolidation processes are interrupted early, only an embryonic hard-ground that represents a minor halt in sedimentation was developed. Sometimes, consolidation processes continued leading to an intraformational hardground. Colonization by Trypanites solitarius (omission suite post-lithification) and Exogyra-like oystreids possibly characterizes hard substrate stage. When two discontinuity surfaces follow closely, a post-omission suite may be defined in relation to the lower cemented surface. As trace fossils are so closely related to changes in the degree of bottom lithification, they prove to be very useful as indicators of substrate evolution. The presence of discontinuity surfaces, evidenced by trace fossil association, suggests changes of sedimentary rate and environmental conditions that should be taken into account in future studies seeking to erect depositional models for these Cretaceous deposits.

Low-Loss Waveguides for Terahertz Frequencies

NASA Technical Reports Server (NTRS)

Siegel, Peter; Yeh, Cavour; Shimabukuro, Fred; Fraser, Scott

2008-01-01

Hollow-core, periodic bandgap (HCPBG) flexible waveguides have been proposed as a means of low-loss transmission of electromagnetic signals in the frequency range from about 300 GHz to 30 THz. This frequency range has been called the "terahertz gap" because it has been little utilized: Heretofore, there has been no way of low-loss guiding of terahertz beams other than by use of fixed-path optical beam guides with lenses and mirrors or multimode waveguides that cannot maintain mode purity around bends or modest discontinuities.

Lightning Physics: A Three Year Program

DTIC Science & Technology

1983-01-01

because these aircraft are controlled poeal’ r r o(z’, I- RIC) with low-voltage digital electronics and are in part construct- 4w J(,3 cR "*t • at ed of... millise - limits pretrigger and delayed-trigger mode,. and a variety of sample conds, and hundreds of microseconds, respectively, the time of simple...processes, but we feel it prudent to discontinue use of the Proctor, D. E., A radio study of lightning, Ph.D. thesis , Univ. of designations in order

YAP Version 4.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, Eric M.

2004-05-20

The YAP software library computes (1) electromagnetic modes, (2) electrostatic fields, (3) magnetostatic fields and (4) particle trajectories in 2d and 3d models. The code employs finite element methods on unstructured grids of tetrahedral, hexahedral, prism and pyramid elements, with linear through cubic element shapes and basis functions to provide high accuracy. The novel particle tracker is robust, accurate and efficient, even on unstructured grids with discontinuous fields. This software library is a component of the MICHELLE 3d finite element gun code.

Linear calculations of edge current driven kink modes with BOUT++ code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, G. Q., E-mail: ligq@ipp.ac.cn; Xia, T. Y.; Lawrence Livermore National Laboratory, Livermore, California 94550

This work extends previous BOUT++ work to systematically study the impact of edge current density on edge localized modes, and to benchmark with the GATO and ELITE codes. Using the CORSICA code, a set of equilibria was generated with different edge current densities by keeping total current and pressure profile fixed. Based on these equilibria, the effects of the edge current density on the MHD instabilities were studied with the 3-field BOUT++ code. For the linear calculations, with increasing edge current density, the dominant modes are changed from intermediate-n and high-n ballooning modes to low-n kink modes, and the linearmore » growth rate becomes smaller. The edge current provides stabilizing effects on ballooning modes due to the increase of local shear at the outer mid-plane with the edge current. For edge kink modes, however, the edge current does not always provide a destabilizing effect; with increasing edge current, the linear growth rate first increases, and then decreases. In benchmark calculations for BOUT++ against the linear results with the GATO and ELITE codes, the vacuum model has important effects on the edge kink mode calculations. By setting a realistic density profile and Spitzer resistivity profile in the vacuum region, the resistivity was found to have a destabilizing effect on both the kink mode and on the ballooning mode. With diamagnetic effects included, the intermediate-n and high-n ballooning modes can be totally stabilized for finite edge current density.« less

Antibiotics in the clinical pipeline in 2013.

PubMed

Butler, Mark S; Blaskovich, Mark A; Cooper, Matthew A

2013-10-01

The continued emergence of multi-drug-resistant bacteria is a major public health concern. The identification and development of new antibiotics, especially those with new modes of action, is imperative to help treat these infections. This review lists the 22 new antibiotics launched since 2000 and details the two first-in-class antibiotics, fidaxomicin (1) and bedaquiline (2), launched in 2011 and 2012, respectively. The development status, mode of action, spectra of activity, historical discovery and origin of the drug pharmacophore (natural product, natural product derived, synthetic or protein/mammalian peptide) of the 49 compounds and 6 β-lactamase/β-lactam combinations in active clinical development are discussed, as well as compounds that have been discontinued from clinical development since 2011. New antibacterial pharmacophore templates are also reviewed and analyzed.

Supermode-density-wave-polariton condensation with a Bose–Einstein condensate in a multimode cavity

PubMed Central

Kollár, Alicia J.; Papageorge, Alexander T.; Vaidya, Varun D.; Guo, Yudan; Keeling, Jonathan; Lev, Benjamin L.

2017-01-01

Phase transitions, where observable properties of a many-body system change discontinuously, can occur in both open and closed systems. By placing cold atoms in optical cavities and inducing strong coupling between light and excitations of the atoms, one can experimentally study phase transitions of open quantum systems. Here we observe and study a non-equilibrium phase transition, the condensation of supermode-density-wave polaritons. These polaritons are formed from a superposition of cavity photon eigenmodes (a supermode), coupled to atomic density waves of a quantum gas. As the cavity supports multiple photon spatial modes and because the light–matter coupling can be comparable to the energy splitting of these modes, the composition of the supermode polariton is changed by the light–matter coupling on condensation. By demonstrating the ability to observe and understand density-wave-polariton condensation in the few-mode-degenerate cavity regime, our results show the potential to study similar questions in fully multimode cavities. PMID:28211455

bcc-to-hcp transformation pathways for iron versus hydrostatic pressure: Coupled shuffle and shear modes

NASA Astrophysics Data System (ADS)

Liu, J. B.; Johnson, D. D.

2009-04-01

Using density-functional theory, we calculate the potential-energy surface (PES), minimum-energy pathway (MEP), and transition state (TS) versus hydrostatic pressure σhyd for the reconstructive transformation in Fe from body-centered cubic (bcc) to hexagonal closed-packed (hcp). At fixed σhyd , the PES is described by coupled shear (γ) and shuffle (η) modes and is determined from structurally minimized hcp-bcc energy differences at a set of (η,γ) . We fit the PES using symmetry-adapted polynomials, permitting the MEP to be found analytically. The MEP is continuous and fully explains the transformation and its associated magnetization and volume discontinuity at TS. We show that σhyd (while not able to induce shear) dramatically alters the MEP to drive reconstruction by a shuffle-only mode at ≤30GPa , as observed. Finally, we relate our polynomial-based results to Landau and nudge-elastic-band approaches and show they yield incorrect MEP in general.

Seismology of adolescent neutron stars: Accounting for thermal effects and crust elasticity

NASA Astrophysics Data System (ADS)

Krüger, C. J.; Ho, W. C. G.; Andersson, N.

2015-09-01

We study the oscillations of relativistic stars, incorporating key physics associated with internal composition, thermal gradients and crust elasticity. Our aim is to develop a formalism which is able to account for the state-of-the-art understanding of the complex physics associated with these systems. As a first step, we build models using a modern equation of state including composition gradients and density discontinuities associated with internal phase transitions (like the crust-core transition and the point where muons first appear in the core). In order to understand the nature of the oscillation spectrum, we carry out cooling simulations to provide realistic snapshots of the temperature distribution in the interior as the star evolves through adolescence. The associated thermal pressure is incorporated in the perturbation analysis, and we discuss the presence of g -modes arising as a result of thermal effects. We also consider interface modes due to phase-transitions and the gradual formation of the star's crust and the emergence of a set of shear modes.

Medication use and rural seniors. Who really knows what they are taking?

PubMed Central

Torrible, S. J.; Hogan, D. B.

1997-01-01

OBJECTIVE: To determine whether listings of current medications obtained from the office file of patients' attending physicians and the pharmacy record of patients' dispensing pharmacists corresponded to the actual use of medications in a group of non-institutionalized seniors residing in rural communities. DESIGN: In-home interviews followed by retrospective office chart and pharmacy database reviews. SETTING: Two rural communities in southern Alberta with populations of less than 7000 people. PARTICIPANTS: Twenty-five patients aged 75 years or older residing in the study communities, eight family physicians, and four dispensing pharmacies. MAIN OUTCOME MEASURES: Number of currently consumed prescription drugs, currently consumed over-the-counter (OTC) drugs, and stored or discontinued prescribed medications; knowledge of medications (prescribed, OTC, and stored) by family physicians and pharmacists; and number of prescribers or dispensing pharmacists. RESULTS: Patients took a mean of 56 prescribed medications, took a mean of 3.5 OTC medications, and had a mean of 2.0 stored or discontinued medications. Attending family physicians and primary dispensing pharmacists typically knew of only some of their patients' entire regimen of medications. CONCLUSIONS: Misinformation about medication consumption by seniors was common among health care providers. Undertaking routine medication reviews (with emphasis on OTC use), asking specific questions about actual consumption, encouraging use of one prescriber and one pharmacist, discouraging storage of discontinued medications and reducing use of medication samples should be of benefit. PMID:9154361

46 CFR 151.45-4 - Cargo-handling.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the persons in charge of cargo handling. (h) Auxiliary steam, air, fuel, or electric current. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, fuel, or electric current... started or, if started, shall be discontinued under the following conditions: (1) During severe electrical...

46 CFR 151.45-4 - Cargo-handling.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the persons in charge of cargo handling. (h) Auxiliary steam, air, fuel, or electric current. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, fuel, or electric current... started or, if started, shall be discontinued under the following conditions: (1) During severe electrical...

46 CFR 151.45-4 - Cargo-handling.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the persons in charge of cargo handling. (h) Auxiliary steam, air, fuel, or electric current. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, fuel, or electric current... started or, if started, shall be discontinued under the following conditions: (1) During severe electrical...

46 CFR 151.45-4 - Cargo-handling.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the persons in charge of cargo handling. (h) Auxiliary steam, air, fuel, or electric current. When discharging cargo from one or more barges, the towing vessel may furnish steam, air, fuel, or electric current... started or, if started, shall be discontinued under the following conditions: (1) During severe electrical...

Enjoyment and other reasons for electronic cigarette use: Results from college students in New York.

PubMed

Saddleson, M L; Kozlowski, L T; Giovino, G A; Goniewicz, M L; Mahoney, M C; Homish, G G; Arora, A

2016-03-01

Young people are more likely to have experimented with e-cigarettes (e-cigs) compared with older adults. Few studies identify reasons for experimentation/use of e-cigs among young people; we sought to discover what drives college students to use e-cigs. Undergraduate students (ages 18-23) at four universities in New York State were surveyed. Among e-cig ever users (n=429), reasons for use were examined. A multinomial logistic regression model analyzed the relative risk of reasons for using e-cigs among discontinued, current non-daily and current daily e-cig users. Using e-cigs for enjoyment was associated with current non-daily (RR=2.11, 95% CI=1.18-3.75) and current daily use (RR=19.1, 95% CI=3.71-98.54). Non-daily use was related to use because e-cigs are less toxic than cigarettes (RR=2.80, 95% CI=1.75-4.50). More daily users reported use to quit smoking compared with either non-daily or discontinued users (53.3% vs. 12.2% and 13.3%, respectively; p<0.05). Among current users, 72.3% used for enjoyment, compared with 42.9% of discontinued users (p<0.05). In contrast to adults, who often report e-cig use to quit smoking, young people are less likely to use for this reason. The exception was daily e-cig users, who often reported use for quitting/reduction of smoking. Rather, college students report usage reasons related to affect (e.g. enjoyment). Overall, enjoyment was reported more often than was use for quitting smoking; affective reasons likely play a role in the popularity of e-cigs and should be considered in future assessments of e-cig users. Copyright © 2015 Elsevier Ltd. All rights reserved.

Lack of cooperation between physicians and dentists during osteoporosis treatment may increase fractures and osteonecrosis of the jaw.

PubMed

Taguchi, Akira; Shiraki, Masataka; Sugimoto, Toshitsugu; Ohta, Hiroaki; Soen, Satoshi

2016-07-01

Our previous questionnaire-based survey suggested that discontinuation of antiresorptive agents before tooth extraction may increase adverse events and disturb osteoporosis treatment without completely preventing osteonecrosis of the jaw (O.N.J.). We also found little cooperation between physicians and dentists in Japan. However, limitations of our previous study included a survey of doctors belonging to small clinics and a small sample size. Our current study aimed to confirm the results of our previous survey in doctors mainly belonging to academia. A structured questionnaire including 14 key clinical queries was sent to 1812 physicians of the Japan Osteoporosis Society, and 629 responses were received. Dentists requested discontinuation of many medications that were not associated with the incidence of O.N.J. A total of 523 respondents had received discontinuation requests from dentists. Of these, 97 respondents experienced 119 adverse events including 25 fractures and seven incidences of O.N.J. The ratios of valid responses for fractures were 3.6% and 5.3% in patients with a discontinuation of <3 and ≥3 months, respectively. Those for O.N.J. were 0.7% and 1.6%, respectively. Respondents who refused discontinuation requests reported no cases of O.N.J. Approximately 17% of respondents had patients who discontinued osteoporosis treatment following a requested drug discontinuation after tooth extraction. Approximately 62% of respondents did not request oral health care by a dentist before antiresorptive therapy, and 72% reported no cooperation between physicians and dentists in their region. This study reconfirms the results of our previous survey. Discontinuation of antiresorptive treatment may increase both fractures and O.N.J. Immediate development of a strategy for sharing information about O.N.J. among physicians, dentists, and patients is required to reduce the incidence of both O.N.J. and skeletal events in osteoporosis treatment. Study limitations were selection bias due to low response rate and possible inaccurate responses to the questionnaire.

Habit Discontinuity, Self-Activation, and the Diminishing Influence of Context Change: Evidence from the UK Understanding Society Survey.

PubMed

Thomas, Gregory Owen; Poortinga, Wouter; Sautkina, Elena

2016-01-01

Repeated behaviours in stable contexts can become automatic habits. Habits are resistant to information-based techniques to change behaviour, but are contextually cued, so a change in behaviour context (e.g., location) weakens habit strength and can facilitate greater consideration of the behaviour. This idea was demonstrated in previous work, whereby people with strong environmental attitudes have lower car use, but only after recently moving home. We examine the habit discontinuity hypothesis by analysing the Understanding Society dataset with 18,053 individuals representative of the UK population, measuring time since moving home, travel mode to work, and strength of environmental attitudes. Results support previous findings where car use is significantly lower among those with stronger environmental views (but only after recently moving home), and in addition, demonstrate a trend where this effects decays as the time since moving home increases. We discuss results in light of moving into a new home being a potential 'window of opportunity' to promote pro-environmental behaviours.

Dielectric image line groove antennas for millimeterwaves

NASA Astrophysics Data System (ADS)

Solbach, K.; Wolff, I.

Grooves in the ground plane of dielectric image lines are proposed as a new radiating structure. A figure is included showing the proposed groove structure as a discontinuity in a dielectric image line. A wave incident on the dielectric image line is partly reflected by the discontinuity, partly transmitted across the groove, and partly radiated into space above the line. In a travelling-wave antenna, a number of grooves are arranged below a dielectric guide, with spacings around one guide wavelength to produce a beam in the upper half space. A prescribed aperture distribution can be effected by tapering the series radiation resistance of the grooves. This can be done by adjusting the depths of the grooves with a constant width or by varying the widths of the grooves with a constant depth. Attention is also given to circular grooves. Here, the widths of the holes are chosen so that they can be considered as waveguides operating far below the cut-off frequency of the fundamental circular waveguide mode.

Discontinuous Transition from Direct to Inverse Cascade in Three-Dimensional Turbulence

NASA Astrophysics Data System (ADS)

Sahoo, Ganapati; Alexakis, Alexandros; Biferale, Luca

2017-04-01

Inviscid invariants of flow equations are crucial in determining the direction of the turbulent energy cascade. In this work we investigate a variant of the three-dimensional Navier-Stokes equations that shares exactly the same ideal invariants (energy and helicity) and the same symmetries (under rotations, reflections, and scale transforms) as the original equations. It is demonstrated that the examined system displays a change in the direction of the energy cascade when varying the value of a free parameter which controls the relative weights of the triadic interactions between different helical Fourier modes. The transition from a forward to inverse cascade is shown to occur at a critical point in a discontinuous manner with diverging fluctuations close to criticality. Our work thus supports the observation that purely isotropic and three-dimensional flow configurations can support inverse energy transfer when interactions are altered and that inside all turbulent flows there is a competition among forward and backward transfer mechanisms which might lead to multiple energy-containing turbulent states.

Habit Discontinuity, Self-Activation, and the Diminishing Influence of Context Change: Evidence from the UK Understanding Society Survey

PubMed Central

Thomas, Gregory Owen; Poortinga, Wouter; Sautkina, Elena

2016-01-01

Repeated behaviours in stable contexts can become automatic habits. Habits are resistant to information-based techniques to change behaviour, but are contextually cued, so a change in behaviour context (e.g., location) weakens habit strength and can facilitate greater consideration of the behaviour. This idea was demonstrated in previous work, whereby people with strong environmental attitudes have lower car use, but only after recently moving home. We examine the habit discontinuity hypothesis by analysing the Understanding Society dataset with 18,053 individuals representative of the UK population, measuring time since moving home, travel mode to work, and strength of environmental attitudes. Results support previous findings where car use is significantly lower among those with stronger environmental views (but only after recently moving home), and in addition, demonstrate a trend where this effects decays as the time since moving home increases. We discuss results in light of moving into a new home being a potential ‘window of opportunity’ to promote pro-environmental behaviours. PMID:27120333

On long-time instabilities in staggered finite difference simulations of the seismic acoustic wave equations on discontinuous grids

NASA Astrophysics Data System (ADS)

Gao, Longfei; Ketcheson, David; Keyes, David

2018-02-01

We consider the long-time instability issue associated with finite difference simulation of seismic acoustic wave equations on discontinuous grids. This issue is exhibited by a prototype algebraic problem abstracted from practical application settings. Analysis of this algebraic problem leads to better understanding of the cause of the instability and provides guidance for its treatment. Specifically, we use the concept of discrete energy to derive the proper solution transfer operators and design an effective way to damp the unstable solution modes. Our investigation shows that the interpolation operators need to be matched with their companion restriction operators in order to properly couple the coarse and fine grids. Moreover, to provide effective damping, specially designed diffusive terms are introduced to the equations at designated locations and discretized with specially designed schemes. These techniques are applied to simulations in practical settings and are shown to lead to superior results in terms of both stability and accuracy.

Generation of Pc 1 waves by the ion temperature anisotropy associated with fast shocks caused by sudden impulses

NASA Technical Reports Server (NTRS)

Mandt, M. E.; Lee, L. C.

1991-01-01

The high correlation of Pc 1 events with magnetospheric compressions is known. A mechanism is proposed which leads to the generation of Pc 1 waves. The interaction of a dynamic pressure pulse with the earth's bow shock leads to the formation of a weak fast-mode shock propagating into the magnetoshealth. The shock wave can pass right through a tangential discontinuity (magnetopause) and into the magnetosphere, without disturbing either of the structures. In a quasiperpendicular geometry, the shock wave exhibits anisotropic heating. This anisotropy drives unstable ion-cyclotron waves which can contribute to the generation of the Pc 1 waves which are detected. The viability of the mechanism is demonstrated with simulations. This mechanism could explain the peak in the occurrence of observed Pc 1 waves in the postnoon sector where a field-aligned discontinuity in the solar wind would most often be parallel to the magnetopause surface due to the average Parker-spiral magnetic-field configuration.

Demonstration of array eddy current technology for real-time monitoring of laser powder bed fusion additive manufacturing process

NASA Astrophysics Data System (ADS)

Todorov, Evgueni; Boulware, Paul; Gaah, Kingsley

2018-03-01

Nondestructive evaluation (NDE) at various fabrication stages is required to assure quality of feedstock and solid builds. Industry efforts are shifting towards solutions that can provide real-time monitoring of additive manufacturing (AM) fabrication process layer-by-layer while the component is being built to reduce or eliminate dependence on post-process inspection. Array eddy current (AEC), electromagnetic NDE technique was developed and implemented to directly scan the component without physical contact with the powder and fused layer surfaces at elevated temperatures inside a LPBF chamber. The technique can detect discontinuities, surface irregularities, and undesirable metallurgical phase transformations in magnetic and nonmagnetic conductive materials used for laser fusion. The AEC hardware and software were integrated with the L-PBF test bed. Two layer-by-layer tests of Inconel 625 coupons with AM built discontinuities and lack of fusion were conducted inside the L-PBF chamber. The AEC technology demonstrated excellent sensitivity to seeded, natural surface, and near-surface-embedded discontinuities, while also detecting surface topography. The data was acquired and imaged in a layer-by-layer sequence demonstrating the real-time monitoring capabilities of this new technology.

Long-term treatment patterns of testosterone replacement medications.

PubMed

Donatucci, Craig; Cui, Zhanglin; Fang, Yun; Muram, David

2014-08-01

Testosterone replacement therapy (TRT) is prescribed to men diagnosed with hypogonadism to alleviate symptoms, improve quality of life, and improve overall health. However, most men use TRT for only a short duration. To evaluate the long-term treatment patterns in hypogonadal men using topical TRT or short-lasting TRT injections. Using the Truven MarketScan(®) Database, 15,435 men who received their first (index) topical TRT prescription and 517 men who received their short-lasting TRT injection index prescription in 2009 were followed from 12 to 30 months after treatment initiation. Treatment interruption was defined as a medication gap of >30 days. Patients who remained off treatment were classified as having discontinued treatment. Patients who restarted therapy after 30 days were classified as cyclic users. Patients were required to have continuous insurance coverage during 1 year prior to treatment initiation and at least 1 year afterward. Main outcome measures were length of therapy, discontinuation, and restarts of topical TRT or short-lasting TRT injections. The patient characteristics were similar for patients who received topical TRT or short-lasting TRT injections. Of the patients who discontinued therapy during the follow-up period, the percentages of patients who were still on therapy after 3 months were 52% and 31% for topical TRT and short-lasting TRT users, respectively. For cyclic users, there was an attrition rate of approximately 40% to 50% of patients in each cycle. For both topical TRT and short-lasting TRT injections, the gap between stopping and restarting therapy tended to decrease over time. In this analysis, high discontinuation rates were observed. The treatment pattern of TRT may be related to the disease state rather than dosing, daily use, or mode of administration. © 2014 International Society for Sexual Medicine.

The First in situ Observation of Kelvin-Helmholtz Waves at High-Latitude Magnetopause during Strongly Dawnward Interplanetary Magnetic Field Conditions

NASA Technical Reports Server (NTRS)

Hwang, K.-J.; Goldstein, M. L.; Kuznetsova, M. M.; Wang, Y.; Vinas, A. F.; Sibeck, D. G.

2012-01-01

We report the first in situ observation of high-latitude magnetopause (near the northern duskward cusp) Kelvin-Helmholtz waves (KHW) by Cluster on January 12, 2003, under strongly dawnward interplanetary magnetic field (IMF) conditions. The fluctuations unstable to Kelvin-Helmholtz instability (KHI) are found to propagate mostly tailward, i.e., along the direction almost 90 deg. to both the magnetosheath and geomagnetic fields, which lowers the threshold of the KHI. The magnetic configuration across the boundary layer near the northern duskward cusp region during dawnward IMF is similar to that in the low-latitude boundary layer under northward IMF, in that (1) both magnetosheath and magnetospheric fields across the local boundary layer constitute the lowest magnetic shear and (2) the tailward propagation of the KHW is perpendicular to both fields. Approximately 3-hour-long periods of the KHW during dawnward IMF are followed by the rapid expansion of the dayside magnetosphere associated with the passage of an IMF discontinuity that characterizes an abrupt change in IMF cone angle, Phi = acos (B(sub x) / absolute value of Beta), from approx. 90 to approx. 10. Cluster, which was on its outbound trajectory, continued observing the boundary waves at the northern evening-side magnetopause during sunward IMF conditions following the passage of the IMF discontinuity. By comparing the signatures of boundary fluctuations before and after the IMF discontinuity, we report that the frequencies of the most unstable KH modes increased after the discontinuity passed. This result demonstrates that differences in IMF orientations (especially in f) are associated with the properties of KHW at the high-latitude magnetopause due to variations in thickness of the boundary layer, and/or width of the KH-unstable band on the surface of the dayside magnetopause.

Determining the time androgens and sex hormone-binding globulin take to return to baseline after discontinuation of oral contraceptives in women with polycystic ovary syndrome: a prospective study.

PubMed

Sánchez, Luis A; Pérez, Marilda; Centeno, Indira; David, Marisa; Kahi, Doris; Gutierrez, Elizabeth

2007-03-01

In this study, discontinuation of oral contraceptive pills in women with polycystic ovary syndrome was followed by the return of all measured androgens and sex hormone-binding globulin levels to basal values after 8 weeks. These observations are pertinent to the measurement of androgens and sex hormone-binding globulin levels in subjects who currently are taking oral contraceptive pills and have symptoms that are related to polycystic ovary syndrome.

FDTD modeling of thin impedance sheets

NASA Technical Reports Server (NTRS)

Luebbers, Raymond; Kunz, Karl

1991-01-01

Thin sheets of resistive or dielectric material are commonly encountered in radar cross section calculations. Analysis of such sheets is simplified by using sheet impedances. It is shown that sheet impedances can be modeled easily and accurately using Finite Difference Time Domain (FDTD) methods. These sheets are characterized by a discontinuity in the tangential magnetic field on either side of the sheet but no discontinuity in tangential electric field. This continuity, or single valued behavior of the electric field, allows the sheet current to be expressed in terms of an impedance multiplying this electric field.

Tuberculosis treatment discontinuation and symptom persistence: an observational study of Bihar, India’s public care system covering >100,000,000 inhabitants

PubMed Central

2014-01-01

Background The effectiveness of India’s TB control programs depend critically on patients completing appropriate treatment. Discontinuing treatment prior to completion can leave patients infectious and symptomatic. Developing strategies to reduce early discontinuation requires characterizing its patterns and their link to symptom persistence. Methods The 2011 BEST-TB survey (360 clusters, 11 districts) sampled patients (n = 1007) from Bihar’s public healthcare system who had initiated treatment >6 months prior to being interviewed, administering questionnaires to patients about TB treatment duration and symptoms, prior treatment, and sociodemographic characteristics. Multivariate logistic regression models estimated the risk of treatment discontinuation for these characteristics. Similar models estimated probabilities of symptom persistence to 25 weeks post-treatment initiation adjusting for the same predictors and treatment duration. All models included district fixed effects, robust standard errors, and adjustments for the survey sampling design. Treatment default timing and symptom persistence relied solely on self-report. Results 24% of patients discontinued treatment prior to 25 weeks. Higher likelihood of discontinuation occurred in those who had failed to complete previous TB treatment episodes (aOR: 4.77 [95% CI: 1.98 – 11.53]) and those seeing multiple providers (3.67 per provider [1.94 – 6.95]). Symptoms persisted in 42% of patients discontinuing treatment within 5 weeks versus 28% for completing 25 weeks of treatment. Symptom persistence was more likely for those with prior TB treatment (aOR: 5.05 [1.90 – 13.38]); poorer patients (2.94 [1.51 – 5.72]); and women (1.79 [1.07 – 2.99]). Predictors for treatment discontinuation prior to 16 weeks were similar. Conclusions Premature TB treatment discontinuation and symptom persistence is particularly high among individuals who have failed to complete treatment for a prior episode. Strategies to identify and promote treatment completion in this group appear promising. Likewise, effective TB regimens of shortened duration currently in trials may eventually help to achieve higher treatment completion rates. PMID:24886314

Secular changes of the M2 tide in the Gulf of Maine

NASA Technical Reports Server (NTRS)

Ray, Richard D.

2005-01-01

Analyses of long time series of hourly tide-gauge data at four stations in the Gulf of Maine reveal that the amplitude of the M2 tide underwent a nearly linear secular increase throughout most of the twentieth century. In the early 1980s, however, the amplitude of M2 abruptly dropped. Sea level changes alone appear inadequate to explain either the long-term trend or the recent trend discontinuity. Tidal models that account for Holocene sea level rise do predict an amplification of M2, but much smaller than the currently observed trends. Nor do recent annual mean sea levels correlate with the recent trend discontinuity. Some unknown fraction of the open Atlantic may be similarly affected, since the M2 discontinuity, but not the long-term secular increase in the tide, is evident also at Halifax.

Finite element simulation of core inspection in helicopter rotor blades using guided waves.

PubMed

Chakrapani, Sunil Kishore; Barnard, Daniel; Dayal, Vinay

2015-09-01

This paper extends the work presented earlier on inspection of helicopter rotor blades using guided Lamb modes by focusing on inspecting the spar-core bond. In particular, this research focuses on structures which employ high stiffness, high density core materials. Wave propagation in such structures deviate from the generic Lamb wave propagation in sandwich panels. To understand the various mode conversions, finite element models of a generalized helicopter rotor blade were created and subjected to transient analysis using a commercial finite element code; ANSYS. Numerical simulations showed that a Lamb wave excited in the spar section of the blade gets converted into Rayleigh wave which travels across the spar-core section and mode converts back into Lamb wave. Dispersion of Rayleigh waves in multi-layered half-space was also explored. Damage was modeled in the form of a notch in the core section to simulate a cracked core, and delamination was modeled between the spar and core material to simulate spar-core disbond. Mode conversions under these damaged conditions were examined numerically. The numerical models help in assessing the difficulty of using nondestructive evaluation for complex structures and also highlight the physics behind the mode conversions which occur at various discontinuities. Copyright © 2015 Elsevier B.V. All rights reserved.

Fundamentals of diagnostic ultrasonography.

PubMed

Noce, J P

1990-01-01

Diagnostic ultrasonography uses acoustical waves in the frequency range of 1 to 20 MHz. These waves obey Snell's law of reflection and refraction, which are rules ordinary to wave behavior. In ultrasound, the analogy to momentum is acoustic impedance. The acoustic impedance, Z, is equal to the density, p, times velocity, v. The ultrasound transducer converts electrical energy into ultrasound energy and vice versa. The transducer usually consists of a piezoelectric crystal composed of such ceramic materials as barium titanate, lead titanate, zirconate, or lead metaniobate. Five basic ultrasonic scanning modes play the major roles in clinical applications. A-mode, or amplitude-mode, scanning measures the tissue discontinuity along the scan axis. B-mode scanning produces a two-dimensional image of the tissue under study by combining A-mode signals from various directions through mechanical transducer scanning. M-mode, or time motion scanning, is an extension of the A-mode approach in which a single stationary transducer is used. The depth of the echo is displayed on the vertical axis; the brightness of the oscilloscope display is modulated by the echo amplitude. Real-time scanning, or rapid B-scanning, techniques provide continuous data acquisition at a rate sufficient to give the impression of the instantaneous motion of moving structures. Doppler scanning relies on the presence of motion. The Doppler effect occurs when there is relative motion between the source of sound and the receiver of the sound, causing a change in the detected frequency of the sound source.

Association between low-dose acetylsalicylic acid reinitiation and the risk of myocardial infarction or coronary heart disease death.

PubMed

Sáez, María E; González-Pérez, Antonio; Johansson, Saga; Himmelmann, Anders; García Rodríguez, Luis A

2016-07-01

In secondary cardiovascular prevention, discontinuation of acetylsalicylic acid (ASA) is associated with an increased risk of cardiovascular events. This study assessed the impact of ASA reinitiation on the risk of myocardial infarction and coronary heart disease death. Patients prescribed ASA for secondary cardiovascular prevention and who had had a period of ASA discontinuation of ≥90 days in 2000-2007 were identified from The Health Improvement Network (N = 10,453). Incidence of myocardial infarction/coronary heart disease death was calculated. Survival analyses using adjusted Cox proportional hazard models were performed to calculate hazard ratios and 95% confidence intervals for the risk of myocardial infarction/coronary heart disease death associated with ASA use patterns after the initial period of discontinuation. Individuals who were prescribed ASA during follow-up were considered reinitiators. The incidence of myocardial infarction/coronary heart disease death was 8.90 cases per 1000 person-years. Risk of myocardial infarction/coronary heart disease death was similar for current ASA users, who had been continuously exposed since reinitiation, and patients who had not reinitiated ASA (hazard ratio 1.27, 95% confidence interval 0.93-1.73). Among reinitiators, an additional period of ASA discontinuation was associated with increased risk of myocardial infarction/coronary heart disease death compared with no reinitiation (current users: hazard ratio 1.46, 95% confidence interval 1.13-1.90; noncurrent users: hazard ratio 1.70, 95% confidence interval 1.31-2.21). ASA reinitiation was not associated with a decreased risk of myocardial infarction/coronary heart disease death. This may be explained by confounding by indication/comorbidity, whereby higher-risk patients are more likely to reinitiate therapy. An additional period of ASA discontinuation among reinitiators was associated with an increased risk of myocardial infarction/coronary heart disease death. © The European Society of Cardiology 2015.

Solution of cavity resonance and waveguide scattering problems using the eigenmode projection technique

NASA Astrophysics Data System (ADS)

Nasr, Mamdouh H.; Othman, Mohamed A. K.; Eshrah, Islam A.; Abuelfadl, Tamer M.

2017-04-01

New developments in the eigenmode projection technique (EPT) are introduced in solving problems of electromagnetic resonance in closed cavities as well as scattering from discontinuities in guided-wave structures. The EPT invokes the eigenmodes of a canonical predefined cavity in the solution procedure and uses the expansion of these eigenmodes to solve Maxwell's equations, in conjunction with a convenient choice of port boundary conditions. For closed cavities, a new spurious-mode separation method is developed, showing robust and efficient spurious-mode separation. This has been tested using more complex and practical examples demonstrating the powerful use of the presented approach. For waveguide scattering problems, convergence studies are being performed showing stable solutions for a relatively small number of expansion modes, and the proposed method has advantages over conventional solvers in analyzing electromagnetic problems with inhomogeneous materials. These convergence studies also lead to an efficient rule-of-thumb for the number of modes to be used in the simulation. The ability to handle closed and open structures is presented in a unified framework that highlights the generality of the EPT which could be used to analyze and design a variety of microwave components.

Separation of Native Allophycocyanin and R-Phycocyanin from Marine Red Macroalga Polysiphonia urceolata by the Polyacrylamide Gel Electrophoresis Performed in Novel Buffer Systems

PubMed Central

Wang, Yu; Gong, Xueqin; Wang, Shumei; Chen, Lixue; Sun, Li

2014-01-01

Three buffer systems of Imidazole−Acetic acid, HEPES−Imidazole/Bis-tris and Bis-tris−HEPES−MES were designed based on the principle of discontinuous polyacrylamide gel electrophoresis (PAGE) for the native PAGE which could be performed in pH 7.0 and 6.5 in order to analyze and prepare the minor components of allophycocyanin (AP) and R-phycocyanin (R-PC) from marine red macroalga Polysiphonia urceolata. These AP and R-PC phycobiliproteins are easily denatured in alkaline environments. The obtained results demonstrated that the PAGE modes performed in the buffer systems of HEPES−Imidazole/Bis-tris and Bis-tris−HEPES−MES gave the satisfactory resolution and separation of AP and R-PC proteins. The absorption and fluorescence spectra of the AP and R-PC proteins which were prepared by the established PAGE modes proved that they maintained natural spectroscopic characteristics. The established PAGE modes may also provide useful references and selections for some other proteins that are sensitive to alkaline environments or are not effectively separated by the classical PAGE modes performed normally in alkaline buffer systems. PMID:25166028

Simulations on Monitoring and Evaluation of Plasticity-Driven Material Damage Based on Second Harmonic of S0 Mode Lamb Waves in Metallic Plates

PubMed Central

Sun, Xiaoqiang; Liu, Xuyang; Liu, Yaolu; Hu, Ning; Zhao, Youxuan; Ding, Xiangyan; Qin, Shiwei; Zhang, Jianyu; Zhang, Jun; Liu, Feng; Fu, Shaoyun

2017-01-01

In this study, a numerical approach—the discontinuous Meshless Local Petrov-Galerkin-Eshelby Method (MLPGEM)—was adopted to simulate and measure material plasticity in an Al 7075-T651 plate. The plate was modeled in two dimensions by assemblies of small particles that interact with each other through bonding stiffness. The material plasticity of the model loaded to produce different levels of strain is evaluated with the Lamb waves of S0 mode. A tone burst at the center frequency of 200 kHz was used as excitation. Second-order nonlinear wave was extracted from the spectrogram of a signal receiving point. Tensile-driven plastic deformation and cumulative second harmonic generation of S0 mode were observed in the simulation. Simulated measurement of the acoustic nonlinearity increased monotonically with the level of tensile-driven plastic strain captured by MLPGEM, whereas achieving this state by other numerical methods is comparatively more difficult. This result indicates that the second harmonics of S0 mode can be employed to monitor and evaluate the material or structural early-stage damage induced by plasticity. PMID:28773188

Quasi-periodic dynamics in system with multilevel pulse modulated control

NASA Astrophysics Data System (ADS)

Gol'tsov, Yu A.; Kizhuk, A. S.; Rubanov, V. G.

2018-03-01

In this paper, the authors describe the transitions from the regular periodic mode to quasiperiodicity that can be observed in a multilevel pulse-width modulated control system for a high-power heating unit. The behavior of such system can be described by a set of two coupled non-autonomous differential equations with discontinuous right-hand sides. The authors reduce the investigation of this system to the studying of a two-dimensional piecewise-smooth map. The authors demonstrate how a closed invariant curve associated with quasiperiodic dynamics can arise from a stable periodic motion through a border-collision bifurcation. The paper also considers a variety of interesting nonlinear phenomena, including phase-locking modes, the coexistence of several stable closed invariant curves, embedded one into the other and with their basins of attraction separated by intervening repelling closed curves.

Fault tolerant control based on interval type-2 fuzzy sliding mode controller for coaxial trirotor aircraft.

PubMed

Zeghlache, Samir; Kara, Kamel; Saigaa, Djamel

2015-11-01

In this paper, a robust controller for a Six Degrees of Freedom (6 DOF) coaxial trirotor helicopter control is proposed in presence of defects in the system. A control strategy based on the coupling of the interval type-2 fuzzy logic control and sliding mode control technique are used to design a controller. The main purpose of this work is to eliminate the chattering phenomenon and guaranteeing the stability and the robustness of the system. In order to achieve this goal, interval type-2 fuzzy logic control has been used to generate the discontinuous control signal. The simulation results have shown that the proposed control strategy can greatly alleviate the chattering effect, and perform good reference tracking in presence of defects in the system. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Hybrid finite element/waveguide mode analysis of passive RF devices

NASA Astrophysics Data System (ADS)

McGrath, Daniel T.

1993-07-01

A numerical solution for time-harmonic electromagnetic fields in two-port passive radio frequency (RF) devices has been developed, implemented in a computer code, and validated. Vector finite elements are used to represent the fields in the device interior, and field continuity across waveguide apertures is enforced by matching the interior solution to a sum of waveguide modes. Consequently, the mesh may end at the aperture instead of extending into the waveguide. The report discusses the variational formulation and its reduction to a linear system using Galerkin's method. It describes the computer code, including its interface to commercial CAD software used for geometry generation. It presents validation results for waveguide discontinuities, coaxial transitions, and microstrip circuits. They demonstrate that the method is an effective and versatile tool for predicting the performance of passive RF devices.

ON INTERMITTENT TURBULENCE HEATING OF THE SOLAR WIND: DIFFERENCES BETWEEN TANGENTIAL AND ROTATIONAL DISCONTINUITIES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Xin; Tu Chuanyi; He Jiansen

The intermittent structures in solar wind turbulence, studied by using measurements from the WIND spacecraft, are identified as being mostly rotational discontinuities (RDs) and rarely tangential discontinuities (TDs) based on the technique described by Smith. Only TD-associated current sheets (TCSs) are found to be accompanied with strong local heating of the solar wind plasma. Statistical results show that the TCSs have a distinct tendency to be associated with local enhancements of the proton temperature, density, and plasma beta, and a local decrease of magnetic field magnitude. Conversely, for RDs, our statistical results do not reveal convincing heating effects. These resultsmore » confirm the notion that dissipation of solar wind turbulence can take place in intermittent or locally isolated small-scale regions which correspond to TCSs. The possibility of heating associated with RDs is discussed.« less

Forced-Air Warming Discontinued: Periprosthetic Joint Infection Rates Drop.

PubMed

Augustine, Scott D

2017-06-23

Several studies have shown that the waste heat from forced-air warming (FAW) escapes near the floor and warms the contaminated air resident near the floor. The waste heat then forms into convection currents that rise up and contaminate the sterile field above the surgical table. It has been shown that a single airborne bacterium can cause a periprosthetic joint infection (PJI) following joint replacement surgery. We retrospectively compared PJI rates during a period of FAW to a period of air-free conductive fabric electric warming (CFW) at three hospitals. Surgical and antibiotic protocols were held constant. The pooled multicenter data showed a decreased PJI rate of 78% following the discontinuation of FAW and a switch to air-free CFW (n=2034; P=0.002). The 78% reduction in joint implant infections observed when FAW was discontinued suggests that there is a link between the waste FAW heat and PJIs.

Forced-Air Warming Discontinued: Periprosthetic Joint Infection Rates Drop

PubMed Central

Augustine, Scott D.

2017-01-01

Several studies have shown that the waste heat from forced-air warming (FAW) escapes near the floor and warms the contaminated air resident near the floor. The waste heat then forms into convection currents that rise up and contaminate the sterile field above the surgical table. It has been shown that a single airborne bacterium can cause a periprosthetic joint infection (PJI) following joint replacement surgery. We retrospectively compared PJI rates during a period of FAW to a period of air-free conductive fabric electric warming (CFW) at three hospitals. Surgical and antibiotic protocols were held constant. The pooled multicenter data showed a decreased PJI rate of 78% following the discontinuation of FAW and a switch to air-free CFW (n=2034; P=0.002). The 78% reduction in joint implant infections observed when FAW was discontinued suggests that there is a link between the waste FAW heat and PJIs. PMID:28713524

METAL RESISTIVITY MEASURING DEVICE

DOEpatents

Renken, J. Jr.; Myers, R.G.

1960-12-20

An eddy current device is offered for detecting discontinuities in metal samples. Alternate short and long duration pulses are inductively applied to a metal sample via the outer coil of a probe. The long pulses give a resultant signal from the metal sample responsive to probe-tosample spacing and discontinuities within the sample and the shont pulses give a resultant signal responsive only to probe -to-sample spacing. The inner coil of the probe detects the two resultant signals and transmits them to a separation network where the two signals are separated. The two separated signals are then transmitted to a compensation network where the detected signals due to the short pulses are used to compensate for variations due to probe-to-sample spacing contained in the detected signals from the long pulses. Thus, a resultant signal is obtained responsive to discontinuities within the sample and independent of probe-to- sample spacing.

Metal Resistivity Measuring Device

DOEpatents

Renken, Jr, C. J.; Myers, R. G.

1960-12-20

An eddy current device is designed for detecting discontinuities in metal samples. Alternate short and long duration pulses are inductively applied to a metal sample via the outer coil of a probe. The lorg pulses give a resultant signal from the metal sample responsive to probe-tosample spacing and discontinuities with the sample, and the short pulses give a resultant signal responsive only to probe-to-sample spacing. The inner coil of the probe detects the two resultant signals and transmits them to a separation network where the two signals are separated. The two separated signals are then transmitted to a compensation network where the detected signals due to the short pulses are used to compensate for variations due to probeto-sample spacing contained in the detected signals from the long pulses. Thus a resultant signal is obtained responsive to discontinuities within the sample and independent of probe-to- sample spacing.

Interferometric fiber-optic temperature sensor with spiral polarization couplers

NASA Astrophysics Data System (ADS)

Cortés, R.; Khomenko, A. V.; Starodumov, A. N.; Arzate, N.; Zenteno, L. A.

1998-09-01

A fiber optic temperature sensor, for which the changes in modal birefringence of a short section of a long birefringent fiber are monitored remotely, is described. It employs a white light interferometer, which is formed by two concatenated spiral polarization mode couplers. A new method for white light interferometer output signal processing is described which provides a high accuracy absolute temperature measurement even in discontinuous operation of the sensor. Experimental results are presented for temperature measurements over a 100°C range with resolution of 3×10 -3 °C.

Modeling of liquid flow in surface discontinuities

NASA Astrophysics Data System (ADS)

Lobanova, I. S.; Meshcheryakov, V. A.; Kalinichenko, A. N.

2018-01-01

Polymer composite and metallic materials have found wide application in various industries such as aviation, rocket, car manufacturing, ship manufacturing, etc. Many design elements need permanent quality control. Ensuring high quality and reliability of products is impossible without effective nondestructive testing methods. One of these methods is penetrant testing using penetrating substances based on liquid penetration into defect cavities. In this paper, we propose a model of liquid flow to determine the rates of filling the defect cavities with various materials and, based on this, to choose optimal control modes.

Proceedings of the Antenna Applications Symposium Held in Illinois, Robert Allerton Park on 21-23 September 1988. Volume 2

DTIC Science & Technology

1989-06-01

for stainless steel airlines of a nominal length of 7.5 cm, a temperature .hanne of +30C changes the length about ±--_1 electrical degree at 18 GHz...regions, each of which satisfies the source- free boundary conditions. The sum of these modes are then matched to the source discontinuity. The wave...dimension H, perpendicular to the array, represents a free dimension in linear array design limited only by the minimum field-of-view (FOV) orthogonal

Cyber Security Vulnerabilities During Long Term Evolution Power-Saving Discontinuous Reception Protocol

DTIC Science & Technology

2014-06-01

2G second generation 3G third generation 3GPP Third Generation Partnership Project 4G fourth generation AAA authentication, authorization and...RRC_IDLE or the RRC_CONNECTED states in 4G LTE as shown in Figure 19. 2G and 3G networks use DRX in idle mode only. In Figure 19, LTE-U_u is the new DRX...is a wireless access communications network that consists of base stations called eNodeBs (eNBs), which allow connectivity between the mobile device

Sublaminate- or ply-level analysis of composites and strain energy release rates of end-notch and mixed-mode fracture specimens

NASA Technical Reports Server (NTRS)

Valisetty, Rao R.; Chamis, Christos C.

1988-01-01

The sublaminate or ply-level analysis of composite structures is presently undertaken by a computational procedure yielding the stresses in regions affected by delaminations, transverse cracks, and discontinuities that are related to material properties, geometries, and loads. Attention is given to layers or groups of layers that are immediately affected by flaws; these are analyzed as if they were homogeneous bodies in equilibrium, in isolation from the rest of the laminate. Computed stresses agree with those from a three-dimensional FEM analysis.

Explicit filtering in large eddy simulation using a discontinuous Galerkin method

NASA Astrophysics Data System (ADS)

Brazell, Matthew J.

The discontinuous Galerkin (DG) method is a formulation of the finite element method (FEM). DG provides the ability for a high order of accuracy in complex geometries, and allows for highly efficient parallelization algorithms. These attributes make the DG method attractive for solving the Navier-Stokes equations for large eddy simulation (LES). The main goal of this work is to investigate the feasibility of adopting an explicit filter in the numerical solution of the Navier-Stokes equations with DG. Explicit filtering has been shown to increase the numerical stability of under-resolved simulations and is needed for LES with dynamic sub-grid scale (SGS) models. The explicit filter takes advantage of DG's framework where the solution is approximated using a polyno- mial basis where the higher modes of the solution correspond to a higher order polynomial basis. By removing high order modes, the filtered solution contains low order frequency content much like an explicit low pass filter. The explicit filter implementation is tested on a simple 1-D solver with an initial condi- tion that has some similarity to turbulent flows. The explicit filter does restrict the resolution as well as remove accumulated energy in the higher modes from aliasing. However, the ex- plicit filter is unable to remove numerical errors causing numerical dissipation. A second test case solves the 3-D Navier-Stokes equations of the Taylor-Green vortex flow (TGV). The TGV is useful for SGS model testing because it is initially laminar and transitions into a fully turbulent flow. The SGS models investigated include the constant coefficient Smagorinsky model, dynamic Smagorinsky model, and dynamic Heinz model. The constant coefficient Smagorinsky model is over dissipative, this is generally not desirable however it does add stability. The dynamic Smagorinsky model generally performs better, especially during the laminar-turbulent transition region as expected. The dynamic Heinz model which is based on an improved model, handles the laminar-turbulent transition region well while also showing additional robustness.

Mechanical conditions and modes of paraglacial deep-seated gravitational spreading in Valles Marineris, Mars

NASA Astrophysics Data System (ADS)

Makowska, Magdalena; Mège, Daniel; Gueydan, Frédéric; Chéry, Jean

2016-09-01

Deep-seated gravitational spreading (DSGS) affects the slopes of formerly glaciated mountain ridges. On Mars, DSGS has played a key role in shaping the landforms of the giant Valles Marineris troughs. Though less spectacular, DSGS is common in terrestrial orogens, where understanding its mechanics is critical in the light of the ongoing climate change because it is a potential source of catastrophic landslides in deglaciated valleys. We conducted parametric numerical studies in order to identify important factors responsible for DSGS initiation. DSGS models are computed using an elastoviscoplastic finite element code. Using ADELI's software, we reproduce topographic ridge spreading under the effect of valley unloading. Two types of spreading topographic ridges are investigated, homogeneous or with horizontal rheological layering. We find that gravitational instabilities are enhanced by high slopes, which increase gravitational stress, and low friction and cohesion, which decrease yield stress. In the unlayered ridge, instability is triggered by glacial unloading with plastic strain concentration inside the ridge and at the base of the high slopes. Vertical fractures develop in the upper part of the slope, potentially leading to fault scarps. Ridge homogeneity promotes a deformation mode controlled by uphill-facing normal faulting and basal bulging. In the second case, the ridge encompasses horizontal geological discontinuities that induce rock mass anisotropy. Discontinuity located at the base of the slope accumulates plastic strain, leading to the formation of a sliding plane evolving into a landslide. The presence of a weak layer at ridge base therefore promotes another slope deformation mode ending up with catastrophic failure. Mechanical conditions and slope height being equal, these conclusions can probably be extrapolated to Earth. Compared with Mars, DSGS on Earth is inhibited because terrestrial topographic gradients are lower than in Valles Marineris, an effect counterbalanced by increased gravitational stress, where the intensity of deformation is enhanced because of the Earth gravity potential.

Ultrashort, high power, and ultralow noise mode-locked optical pulse generation using quantum-dot semiconductor lasers

NASA Astrophysics Data System (ADS)

Choi, Myoung-Taek

This dissertation explores various aspects and potential of optical pulse generation based on active, passive, and hybrid mode-locked quantum dot semiconductor lasers with target applications such as optical interconnect and high speed signal processing. Design guidelines are developed for the single mode operation with suppressed reflection from waveguide discontinuities. The device fabrication procedure is explained, followed by characteristics of FP laser, SOA, and monolithic two-section devices. Short pulse generation from an external cavity mode-locked QD two-section diode laser is studied. High quality, sub-picosecond (960 fs), high peak power (1.2 W) pulse trains are obtained. The sign and magnitude of pulse chirp were measured for the first time. The role of the self-phase modulation and the linewidth enhancement factor in QD mode-locked lasers is addressed. The noise performance of two-section mode-locked lasers and a SOA-based ring laser was investigated. Significant reduction of the timing jitter under hybrid mode-locked operation was achieved owing to more than one order of magnitude reduction of the linewidth in QD gain media. Ultralow phase noise performance (integrated timing jitter of a few fs at a 10 GHz repetition rate) was demonstrated from an actively mode-locked unidirectional ring laser. These results show that quantum dot mode-locked lasers are strong competitors to conventional semiconductor lasers in noise performance. Finally we demonstrated an opto-electronic oscillator (OEO) and coupled opto-electronic oscillators (COEO) which have the potential for both high purity microwave and low noise optical pulse generation. The phase noise of the COEO is measured by the photonic delay line frequency discriminator method. Based on this study we discuss the prospects of the COEO as a low noise optical pulse source.

Edge plasma boundary layer generated by kink modes in tokamaks

NASA Astrophysics Data System (ADS)

Zakharov, Leonid E.

2011-06-01

This paper describes the structure of the electric current generated by external wall touching and free boundary kink modes at the plasma edge using the ideally conducting plasma model. Both kinds of modes generate δ-functional surface current at the plasma edge. Free boundary kink modes also perturb the core plasma current, which in the plasma edge compensates the difference between the δ-functional surface currents of free boundary and wall touching kink modes. In addition, the resolution of an apparent paradox with the pressure balance across the plasma boundary in the presence of the surface currents is provided.

Uniaxial experimental study of the acoustic emission and deformation behavior of composite rock based on 3D digital image correlation (DIC)

NASA Astrophysics Data System (ADS)

Cheng, Jian-Long; Yang, Sheng-Qi; Chen, Kui; Ma, Dan; Li, Feng-Yuan; Wang, Li-Ming

2017-12-01

In this paper, uniaxial compression tests were carried out on a series of composite rock specimens with different dip angles, which were made from two types of rock-like material with different strength. The acoustic emission technique was used to monitor the acoustic signal characteristics of composite rock specimens during the entire loading process. At the same time, an optical non-contact 3D digital image correlation technique was used to study the evolution of axial strain field and the maximal strain field before and after the peak strength at different stress levels during the loading process. The effect of bedding plane inclination on the deformation and strength during uniaxial loading was analyzed. The methods of solving the elastic constants of hard and weak rock were described. The damage evolution process, deformation and failure mechanism, and failure mode during uniaxial loading were fully determined. The experimental results show that the θ = 0{°}-45{°} specimens had obvious plastic deformation during loading, and the brittleness of the θ = 60{°}-90{°} specimens gradually increased during the loading process. When the anisotropic angle θ increased from 0{°} to 90{°}, the peak strength, peak strain, and apparent elastic modulus all decreased initially and then increased. The failure mode of the composite rock specimen during uniaxial loading can be divided into three categories: tensile fracture across the discontinuities (θ = 0{°}-30{°}), sliding failure along the discontinuities (θ = 45{°}-75{°}), and tensile-split along the discontinuities (θ = 90{°}). The axial strain of the weak and hard rock layers in the composite rock specimen during the loading process was significantly different from that of the θ = 0{°}-45{°} specimens and was almost the same as that of the θ = 60{°}-90{°} specimens. As for the strain localization highlighted in the maximum principal strain field, the θ = 0{°}-30{°} specimens appeared in the rock matrix approximately parallel to the loading direction, while in the θ = 45{°}-90{°} specimens it appeared at the hard and weak rock layer interface.

High-Order Entropy Stable Formulations for Computational Fluid Dynamics

NASA Technical Reports Server (NTRS)

Carpenter, Mark H.; Fisher, Travis C.

2013-01-01

A systematic approach is presented for developing entropy stable (SS) formulations of any order for the Navier-Stokes equations. These SS formulations discretely conserve mass, momentum, energy and satisfy a mathematical entropy inequality. They are valid for smooth as well as discontinuous flows provided sufficient dissipation is added at shocks and discontinuities. Entropy stable formulations exist for all diagonal norm, summation-by-parts (SBP) operators, including all centered finite-difference operators, Legendre collocation finite-element operators, and certain finite-volume operators. Examples are presented using various entropy stable formulations that demonstrate the current state-of-the-art of these schemes.

Can CabECO® technology be used for the disinfection of highly faecal-polluted surface water?

PubMed

Isidro, Julia; Llanos, Javier; Sáez, Cristina; Brackemeyer, Dirk; Cañizares, Pablo; Matthee, Thorsten; Rodrigo, Manuel A

2018-06-18

In this work, the disinfection of highly faecal-polluted surface water was studied using a new electrochemical cell (CabECO ® cell, manufactured by CONDIAS) specifically designed to produce ozone in water with very low conductivity. The disinfection tests were carried out in a discontinuous mode to evaluate the influence of the electrode current charge passed. The effect of the current density was also studied in order to optimize the disinfection conditions and to simultaneously prevent the formation of undesirable by-products (chlorates and perchlorates) during the electrolysis. The results demonstrate that this technology is robust and efficient, and it can suitably disinfect water. During electrolysis, the chloride contained in the water was oxidized to hypochlorite, and this compound was combined with ammonia to form chloramines. Both hypochlorite and chloramines (formed by the well-known break point reaction) promoted persistent disinfection and seemed to be mainly responsible for the disinfection attained during the electrochemical process. Chlorate and perchlorate could also be produced, although the low concentrations of chloride in the tested water made them irrelevant. The removal of the total organic carbon under the applied operating conditions was not very efficient (although it reached 50% in 2 h) and the production of trihalomethanes was very low, below 100 ppb for all tests. Copyright © 2018 Elsevier Ltd. All rights reserved.

Probing longitudinal modes evolution of a InGaN green laser diode

NASA Astrophysics Data System (ADS)

Chen, Yi-Hsi; Lin, Wei-Chen; Chen, Hong-Zui; Shy, Jow-Tsong; Chui, Hsiang-Chen

2018-06-01

This study aims to investigate the longitudinal mode evolution of a InGaN green laser diode. A spectrometer with a 3-pm resolution was employed to obtain the emission spectra of a green laser diode, at a wavelength of around 520 nm, as a function of applied current and temperature. The spectral behavior of the laser modes with applied current was investigated. Right above the lasing threshold, the green diode laser emitted single longitudinal mode output. With increasing applied current, the number of the longitudinal modes increased. Up to ten lasing modes oscillated within the entire gain profile when the applied currents were tuned to 2.2Ith. Subsequently, a multi-Lorentzian profile model was adopted to analyze the spectra and observe how the modes evolved with temperature and applied current.

An ionization region model of the reactive Ar/O2 high power impulse magnetron sputtering discharge

NASA Astrophysics Data System (ADS)

Gudmundsson, J. T.; Lundin, D.; Brenning, N.; Raadu, M. A.; Huo, Chunqing; Minea, T. M.

2016-12-01

A new reactive ionization region model (R-IRM) is developed to describe the reactive Ar/O2 high power impulse magnetron sputtering (HiPIMS) discharge with a titanium target. It is then applied to study the temporal behavior of the discharge plasma parameters such as electron density, the neutral and ion composition, the ionization fraction of the sputtered vapor, the oxygen dissociation fraction, and the composition of the discharge current. We study and compare the discharge properties when the discharge is operated in the two well established operating modes, the metal mode and the poisoned mode. Experimentally, it is found that in the metal mode the discharge current waveform displays a typical non-reactive evolution, while in the poisoned mode the discharge current waveform becomes distinctly triangular and the current increases significantly. Using the R-IRM we explore the current increase and find that when the discharge is operated in the metal mode Ar+ and Ti+ -ions contribute most significantly (roughly equal amounts) to the discharge current while in the poisoned mode the Ar+ -ions contribute most significantly to the discharge current and the contribution of O+ -ions, Ti+ -ions, and secondary electron emission is much smaller. Furthermore, we find that recycling of atoms coming from the target, that are subsequently ionized, is required for the current generation in both modes of operation. From the R-IRM results it is found that in the metal mode self-sputter recycling dominates and in the poisoned mode working gas recycling dominates. We also show that working gas recycling can lead to very high discharge currents but never to a runaway. It is concluded that the dominating type of recycling determines the discharge current waveform.

Asymptotic, multigroup flux reconstruction and consistent discontinuity factors

DOE PAGES

Trahan, Travis J.; Larsen, Edward W.

2015-05-12

Recent theoretical work has led to an asymptotically derived expression for reconstructing the neutron flux from lattice functions and multigroup diffusion solutions. The leading-order asymptotic term is the standard expression for flux reconstruction, i.e., it is the product of a shape function, obtained through a lattice calculation, and the multigroup diffusion solution. The first-order asymptotic correction term is significant only where the gradient of the diffusion solution is not small. Inclusion of this first-order correction term can significantly improve the accuracy of the reconstructed flux. One may define discontinuity factors (DFs) to make certain angular moments of the reconstructed fluxmore » continuous across interfaces between assemblies in 1-D. Indeed, the standard assembly discontinuity factors make the zeroth moment (scalar flux) of the reconstructed flux continuous. The inclusion of the correction term in the flux reconstruction provides an additional degree of freedom that can be used to make two angular moments of the reconstructed flux continuous across interfaces by using current DFs in addition to flux DFs. Thus, numerical results demonstrate that using flux and current DFs together can be more accurate than using only flux DFs, and that making the second angular moment continuous can be more accurate than making the zeroth moment continuous.« less

Global seismic data reveal little water in the mantle transition zone

NASA Astrophysics Data System (ADS)

Houser, C.

2016-08-01

Knowledge of the Earth's present water content is necessary to constrain the amount of water and other volatiles the Earth acquired during its formation and the amount that is cycled back into the interior from the surface. This study compares 410 and 660 km discontinuity depth with shear wave tomography within the mantle transition zone to identify regions with seismic signals consistent with water. The depth of the 410 and 660 km discontinuities is determined from a large updated dataset of SS-S410S and SS-S660S differential travel times, known as SS precursors. The discontinuity depths measured from binning and stacking the SS precursor data are then compared to the shear velocity model HMSL-S06 in the transition zone. Mapping all the possible combinations, very few locations match the predictions from mineral physics for the effects of water on discontinuity depth and shear velocity. The predictions, although not yet measured at actual transition zone temperatures and pressures, are a shallow 410 km discontinuity, a deep 660 km discontinuity, and a slow shear velocity. Only 8% of the bins with high-quality data are consistent with these predictions, and the calculated average water content within these bins is around 0.6 wt.%. A few isolated locations have patterns of velocity/topography that are consistent with water, while there are large regional-scale patterns consistent with cold/hot temperature anomalies. Combining this global analysis of long period seismic data and the current mineral physics predictions for water in transition zone minerals, I find that the mantle transition zone is generally dry, containing less than one Earth ocean of water. Although subduction zones could be locally hydrated, the combined discontinuity and velocity data show no evidence that wadsleyite or ringwoodite have been globally hydrated by subduction or initial Earth conditions.

Factors influencing patient decisions to initiate and discontinue subcutaneous testosterone pellets (Testopel) for treatment of hypogonadism.

PubMed

Smith, Ryan P; Khanna, Abhinav; Coward, Robert M; Rajanahally, Saneal; Kovac, Jason R; Gonzales, Marshall A; Lipshultz, Larry I

2013-09-01

A variety of modalities for testosterone replacement therapy (TRT) are available, including topical gels, injections, and Testopel subcutaneous testosterone pellets (STP). STP are becoming more commonly utilized in the United States; however, patient preferences, expectations, and usage patterns regarding this therapy remain poorly characterized. To identify factors influencing patients' decisions to initiate or discontinue STP. A total of 175 men from an academic urology clinic who were currently using or who had previously used STP for hypogonadism received a 32-item electronic survey. Assessment of the impact of convenience, efficacy, side effects, cost, and symptom relief on initiation and discontinuation of STP. One hundred and thirteen men (64.6% response rate) of mean age 51.4 years who previously underwent a mean of 2.8 STP implant procedures completed the survey. Fifty-nine (52.2%) and 40 (35.4%) men had switched to STP from topical gel and injection therapy, respectively, whereas 14 (12.4%) men initially started TRT with STP. Convenience (68.8%) was the most important factor in patients' decision to start STP, while cost of the previous form of TRT (14.7%) was least important. At the time of the survey, 32 men (28.3%) had discontinued STP therapy. Cost of therapy (50%) was the primary factor in discontinuing STP. There was no difference in serum testosterone levels between men who continued STP and those who discontinued therapy (642.8 vs. 629.0 ng/dL, P = 0.83). Overall, 68.1% of patients continued STP therapy at the time of survey completion. Convenience is the most important factor in a patient's decision to initiate STP; however, physician recommendation also plays a substantial role. Cost was the primary reason for discontinuation. Upon survey completion, greater than two-thirds of respondents elected to continue STP therapy. STP are a viable treatment option for hypogonadal men seeking a convenient and efficacious alternative modality of TRT. © 2013 International Society for Sexual Medicine.

Anomalous Refraction of Acoustic Guided Waves in Solids with Geometrically Tapered Metasurfaces.

PubMed

Zhu, Hongfei; Semperlotti, Fabio

2016-07-15

The concept of a metasurface opens new exciting directions to engineer the refraction properties in both optical and acoustic media. Metasurfaces are typically designed by assembling arrays of subwavelength anisotropic scatterers able to mold incoming wave fronts in rather unconventional ways. The concept of a metasurface was pioneered in photonics and later extended to acoustics while its application to the propagation of elastic waves in solids is still relatively unexplored. We investigate the design of acoustic metasurfaces to control elastic guided waves in thin-walled structural elements. These engineered discontinuities enable the anomalous refraction of guided wave modes according to the generalized Snell's law. The metasurfaces are made out of locally resonant toruslike tapers enabling an accurate phase shift of the incoming wave, which ultimately affects the refraction properties. We show that anomalous refraction can be achieved on transmitted antisymmetric modes (A_{0}) either when using a symmetric (S_{0}) or antisymmetric (A_{0}) incident wave, the former clearly involving mode conversion. The same metasurface design also allows achieving structure embedded planar focal lenses and phase masks for nonparaxial propagation.

Finite-time containment control of perturbed multi-agent systems based on sliding-mode control

NASA Astrophysics Data System (ADS)

Yu, Di; Ji, Xiang Yang

2018-01-01

Aimed at faster convergence rate, this paper investigates finite-time containment control problem for second-order multi-agent systems with norm-bounded non-linear perturbation. When topology between the followers are strongly connected, the nonsingular fast terminal sliding-mode error is defined, corresponding discontinuous control protocol is designed and the appropriate value range of control parameter is obtained by applying finite-time stability analysis, so that the followers converge to and move along the desired trajectories within the convex hull formed by the leaders in finite time. Furthermore, on the basis of the sliding-mode error defined, the corresponding distributed continuous control protocols are investigated with fast exponential reaching law and double exponential reaching law, so as to make the followers move to the small neighbourhoods of their desired locations and keep within the dynamic convex hull formed by the leaders in finite time to achieve practical finite-time containment control. Meanwhile, we develop the faster control scheme according to comparison of the convergence rate of these two different reaching laws. Simulation examples are given to verify the correctness of theoretical results.

Gaussian-windowed frame based method of moments formulation of surface-integral-equation for extended apertures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shlivinski, A., E-mail: amirshli@ee.bgu.ac.il; Lomakin, V., E-mail: vlomakin@eng.ucsd.edu

2016-03-01

Scattering or coupling of electromagnetic beam-field at a surface discontinuity separating two homogeneous or inhomogeneous media with different propagation characteristics is formulated using surface integral equation, which are solved by the Method of Moments with the aid of the Gabor-based Gaussian window frame set of basis and testing functions. The application of the Gaussian window frame provides (i) a mathematically exact and robust tool for spatial-spectral phase-space formulation and analysis of the problem; (ii) a system of linear equations in a transmission-line like form relating mode-like wave objects of one medium with mode-like wave objects of the second medium; (iii)more » furthermore, an appropriate setting of the frame parameters yields mode-like wave objects that blend plane wave properties (as if solving in the spectral domain) with Green's function properties (as if solving in the spatial domain); and (iv) a representation of the scattered field with Gaussian-beam propagators that may be used in many large (in terms of wavelengths) systems.« less

A least-squares parameter estimation algorithm for switched hammerstein systems with applications to the VOR

NASA Technical Reports Server (NTRS)

Kukreja, Sunil L.; Kearney, Robert E.; Galiana, Henrietta L.

2005-01-01

A "Multimode" or "switched" system is one that switches between various modes of operation. When a switch occurs from one mode to another, a discontinuity may result followed by a smooth evolution under the new regime. Characterizing the switching behavior of these systems is not well understood and, therefore, identification of multimode systems typically requires a preprocessing step to classify the observed data according to a mode of operation. A further consequence of the switched nature of these systems is that data available for parameter estimation of any subsystem may be inadequate. As such, identification and parameter estimation of multimode systems remains an unresolved problem. In this paper, we 1) show that the NARMAX model structure can be used to describe the impulsive-smooth behavior of switched systems, 2) propose a modified extended least squares (MELS) algorithm to estimate the coefficients of such models, and 3) demonstrate its applicability to simulated and real data from the Vestibulo-Ocular Reflex (VOR). The approach will also allow the identification of other nonlinear bio-systems, suspected of containing "hard" nonlinearities.

Transmission and reflection of terahertz plasmons in two-dimensional plasmonic devices

DOE PAGES

Sydoruk, Oleksiy; Choonee, Kaushal; Dyer, Gregory Conrad

2015-03-10

We found that plasmons in two-dimensional semiconductor devices will be reflected by discontinuities, notably, junctions between gated and non-gated electron channels. The transmitted and reflected plasmons can form spatially- and frequency-varying signals, and their understanding is important for the design of terahertz detectors, oscillators, and plasmonic crystals. Using mode decomposition, we studied terahertz plasmons incident on a junction between a gated and a nongated channel. The plasmon reflection and transmission coefficients were found numerically and analytically and studied between 0.3 and 1 THz for a range of electron densities. At higher frequencies, we could describe the plasmons by a simplifiedmore » model of channels in homogeneous dielectrics, for which the analytical approximations were accurate. At low frequencies, however, the full geometry and mode spectrum had to be taken into account. Moreover, the results agreed with simulations by the finite-element method. As a result, mode decomposition thus proved to be a powerful method for plasmonic devices, combining the rigor of complete solutions of Maxwell's equations with the convenience of analytical expressions.« less

Nonlinear reconnecting edge localized modes in current-carrying plasmas

DOE PAGES

Ebrahimi, F.

2017-05-22

Nonlinear edge localized modes in a tokamak are examined using global three-dimensional resistive magnetohydrodynamics simulations. Coherent current-carrying filament (ribbon-like) structures wrapped around the torus are nonlinearly formed due to nonaxisymmetric reconnecting current sheet instabilities, the so-called peeling-like edge localized modes. These fast growing modes saturate by breaking axisymmetric current layers isolated near the plasma edge and go through repetitive relaxation cycles by expelling current radially outward and relaxing it back. The local bidirectional fluctuation-induced electromotive force (emf) from the edge localized modes, the dynamo action, relaxes the axisymmetric current density and forms current holes near the edge. Furthermore, the three-dimensionalmore » coherent current-carrying filament structures (sometimes referred to as 3-D plasmoids) observed here should also have strong implications for solar and astrophysical reconnection.« less

First-generation phosphodiesterase type 5 inhibitors dropout: a comprehensive review and meta-analysis.

PubMed

Corona, G; Rastrelli, G; Burri, A; Serra, E; Gianfrilli, D; Mannucci, E; Jannini, E A; Maggi, M

2016-11-01

The discontinuation rate with phosphodiesterase type 5 inhibitors (PDE5i) remains very high. The aim of this study was to review and meta-analyze currently available data regarding dropout of the first-generation of PDE5i including sildenafil, vardenafil, and tadalafil. An extensive Medline Embase and Cochrane search was performed including the following words: 'PDE5i', 'discontinuation'. All observational studies reporting the dropout rate of PDE5i and its specific causes without any arbitrary restrictions were included. Out of 103 retrieved articles, 22 were included in the study. Retrieved trials included a total of 162,936 patients with a mean age of 58.8 ± 7.9 years. Prevalence of reported comorbid diabetes and hypertension were 27.7% and 36.9%, respectively. PDE5i were associated with a mean discontinuation rate of 4% per month (almost 50% after one year). This rate was higher in younger subjects and in those reporting a higher prevalence of associated morbidities. Six main reasons of PDE5i dropout were identified in the evaluated trials. Partner-related problems and lack of efficacy represented the most important reasons for PDE5i discontinuation, although no significant difference among factors was detected. In conclusion, despite their high efficacy and easy administration, the discontinuation rate and dissatisfaction with PDE5i are still very high. Our data showed that no single factor plays a major role in PDE5i dropout, suggesting that the discontinuation rate is usually because of a combination of both medical problems and psychosocial and relational factors. © 2016 American Society of Andrology and European Academy of Andrology.

Evaluation of the United States Public Health Service guidelines for discontinuation of anti-CMV therapy after immune recovery in patients with CMV retinitis

PubMed Central

Holbrook, Janet T.; Colvin, Ryan; Van Natta, Mark L.; Thorne, Jennifer E.; Bardsley, Mark; Jabs, Douglas A.

2011-01-01

Purpose To evaluate US Public Health Service (USPHS) guidelines for discontinuing anti-CMV therapy in patients with AIDS who have immune recovery and quiescent retinitis after initiating highly active anti-retroviral therapy (HAART). Design Cohort study of patients with CMV retinitis (Longitudinal Study of Ocular Complications of AIDS). Methods Participants had CMV retinitis and CD4+ T-cell counts of 50 cells/uL or fewer enrolled from 1998 to 2009 who demonstrated sustained immune recovery (two consecutive CD4+ T-cell counts of 100 cells/uL or more at least 6 months apart) and inactive retinitis. Participants were classified into 2 groups according to anti-CMV treatment after immune recover: (1) continued anti-CMV therapy and (2) discontinued therapy. We evaluated survival, visual acuity, and CMV retinitis activity; we employed propensity scores to adjust for confounding factors for these analyses. Results Of 152 participants reviewed, 71 demonstrated immune recovery; 37 of whom discontinued therapy and 34 who continued therapy. At immune recovery, participants continuing therapy tended to be older (44 vs 40 years, P=0.09), have bilateral retinitis (53% vs 32%, P=0.10), and have lower CD4+ T-cell counts (148 vs 207 cells/μL, P<0.001). There were no statistical differences in any of the clinical outcomes (death, retinitis progress, visual acuity or incidence of bilateral retinitis). Both groups lost visual acuity during follow-up, on average 1.2 letters per year (P<0.01). Conclusion Discontinuation of anti-CMV therapy after immune recovery did not increase the risk of poor outcomes. These results support the current guidelines for discontinuation of anti-CMV therapy after achievement of sustained immune recovery. PMID:21742304

Evaluation of the United States public health service guidelines for discontinuation of anticytomegalovirus therapy after immune recovery in patients with cytomegalovirus retinitis.

PubMed

Holbrook, Janet T; Colvin, Ryan; van Natta, Mark L; Thorne, Jennifer E; Bardsley, Mark; Jabs, Douglas A

2011-10-01

To evaluate United States Public Health Service (USPHS) guidelines for discontinuing anticytomegalovirus (CMV) therapy in patients with AIDS who have immune recovery and quiescent retinitis after initiating highly active antiretroviral therapy. Cohort study of patients with CMV retinitis (Longitudinal Study of Ocular Complications of AIDS). Participants had CMV retinitis and CD4+ T-cell counts of 50 cells/μL or fewer enrolled from 1998 through 2009 who demonstrated sustained immune recovery (2 consecutive CD4+ T-cell counts of 100 cells/μL or more at least 6 months apart) and inactive retinitis. Participants were classified into 2 groups according to anti-CMV treatment after immune recover: (1) continued anti-CMV therapy and (2) discontinued therapy. We evaluated survival, visual acuity, and CMV retinitis activity; we used propensity scores to adjust for confounding factors for these analyses. Of 152 participants reviewed, 71 demonstrated immune recovery, 37 of whom discontinued therapy and 34 of whom continued therapy. At immune recovery, participants continuing therapy tended to be older (44 vs 40 years; P = .09), have bilateral retinitis (53% vs 32%; P = .10), and have lower CD4+ T-cell counts (148 vs 207 cells/μL; P < .001). There were no statistical differences in any of the clinical outcomes (death, retinitis progress, visual acuity, or incidence of bilateral retinitis). Both groups lost visual acuity during follow-up, on average 1.2 letters per year (P < .01). Discontinuation of anti-CMV therapy after immune recovery did not increase the risk of poor outcomes. These results support the current guidelines for discontinuation of anti-CMV therapy after achievement of sustained immune recovery. Copyright © 2011 Elsevier Inc. All rights reserved.

Abrupt opium discontinuation has no significant triggering effect on acute myocardial infarction.

PubMed

Masoomi, Mohammad; Zare, Jahangir; Nasri, Hamidreza; Mirzazadeh, Ali; Sheikhvatan, Mehrdad

2011-04-01

A deleterious effect of withdrawal symptoms due to abrupt discontinuation of opium on the cardiovascular system is one of the recent interesting topics in the cardiovascular field. The current study hypothesized that the withdrawal syndrome due to discontinuing opium might be an important trigger for the appearance of acute myocardial infarction. Eighty-one opium-addicted individuals who were candidates for cardiovascular clinical evaluation and consecutively hospitalized in the coronary care unit (CCU) ward of Shafa Hospital in Kerman between January and July 2009 were included in the study and categorized in the case group, including patients experiencing withdrawal symptoms within 6-12 h after the reduced or discontinued use of opium according to the Diagnostic and Statistical Manual of Mental Disorders-revised IV version (DSM-IV-R) criteria for opium dependence and withdrawal, and the control group, without opium withdrawal symptoms. The appearance of acute myocardial infarction was compared between the two groups using multivariable regression models. Acute myocardial infarction occurred in 50.0% of those with withdrawal symptoms and in 45.1% of patients without evidence of opium withdrawal (P = 0.669). Multivariable analysis showed that opium withdrawal symptoms were not a trigger for acute myocardial infarction adjusting for demographic characteristics, marital status, education level and common coronary artery disease risk profiles [odds ratio (OR) = 0.920, 95% confidence interval (CI) = 0.350-2.419, P = 0.866]. Also, daily dose of opium before reducing or discontinuing use did not predict the appearance of myocardial infarction in the presence of confounder variables (OR = 0.975, 95% CI = 0.832-1.143, P = 0.755). Withdrawal syndrome due to abrupt discontinuation of opium does not have a triggering role for appearance of acute myocardial infarction.

Hospital Factors Associated With Care Discontinuity Following Emergency General Surgery.

PubMed

Havens, Joaquim M; Olufajo, Olubode A; Tsai, Thomas C; Jiang, Wei; Columbus, Alexandra B; Nitzschke, Stephanie L; Cooper, Zara; Salim, Ali

2017-03-01

Although there is evidence that changes in clinicians during the continuum of care (care discontinuity) are associated with higher mortality and complications among surgical patients, little is known regarding the drivers of care discontinuity among emergency general surgery (EGS) patients. To identify hospital factors associated with care discontinuity among EGS patients. We performed a retrospective analysis of the 100% Medicare inpatient claims file, from January 1, 2008, to November 30, 2011, and matched patient details to hospital information in the 2011 American Hospital Association Annual Survey database. We selected patients aged 65 years and older who had the most common procedures associated with the previously defined American Association for the Surgery of Trauma EGS diagnosis categories and survived to hospital discharge across the United States. The current analysis was conducted from February 1, 2016, to March 24, 2016. Care discontinuity defined as readmission within 30 days to nonindex hospitals. There were 109 443 EGS patients readmitted within 30 days of discharge and 20 396 (18.6%) were readmitted to nonindex hospitals. Of the readmitted patients, 61 340 (56%) were female. Care discontinuity was higher among patients who were male (19.5% vs 18.0%), those younger than 85 years old (19.0% vs 16.6%), and those who lived 12.8 km (8 miles) or more away from the index hospitals (23.7% vs 14.8%) (all P < .001). Care discontinuity was independently associated with mortality (adjusted odds ratio [aOR], 1.16; 95% CI, 1.08-1.25). Hospital factors associated with care discontinuity included bed size of 200 or more (aOR, 1.45; 95% CI, 1.36-1.54), safety-net status (aOR, 1.35; 95% CI, 1.27-1.43), and teaching status (aOR, 1.18; 95% CI, 1.09-1.28). Care discontinuity was significantly lower among designated trauma centers (aOR, 0.89; 95% CI, 0.83-0.94) and highest among hospitals in the Midwest (aOR, 1.15; 95% CI, 1.05-1.26). Nearly 1 in 5 older EGS patients is readmitted to a hospital other than where their original procedure was performed. This care discontinuity is independently associated with mortality and is highest among EGS patients who are treated at large, teaching, safety-net hospitals. These data underscore the need for sustained efforts in increasing continuity of care among these hospitals and highlight the importance of accounting for these factors in risk-adjusted hospital comparisons.

The impact of CFS/ME on employment and productivity in the UK: a cross-sectional study based on the CFS/ME national outcomes database.

PubMed

Collin, Simon M; Crawley, Esther; May, Margaret T; Sterne, Jonathan A C; Hollingworth, William

2011-09-15

Few studies have investigated factors associated with discontinuation of employment in patients with CFS/ME or quantified its impact on productivity. We used patient-level data from five NHS CFS/ME services during the period 01/04/2006-31/03/2010 collated in the UK CFS/ME National Outcomes Database. We used logistic regression to identify factors associated with discontinuation of employment. We estimated UK-wide productivity costs using patient-level data on duration of illness before assessment by a CFS/ME service, duration of unemployment, age, sex and numbers of patients, in conjunction with Office for National Statistics income and population data. Data were available for 2,170 patients, of whom 1,669 (76.9%) were women. Current employment status was recorded for 1,991 patients (91.8%), of whom 811 patients (40.7%) were currently employed and 998 (50.1%) had discontinued their employment "because of fatigue-related symptoms". Older age, male sex, disability, fatigue, pain, and duration of illness were associated with cessation of employment. In a multivariable model, age, male sex, and disability remained as independent predictors. Total productivity costs among the 2,170 patients due to discontinuation of employment in the years preceding assessment by a specialist CFS/ME service (median duration of illness=36 months) were £49.2 million. Our sample was equivalent to 4,424 UK adults accessing specialist services each year, representing productivity costs to the UK economy of £102.2 million. Sensitivity analyses suggested a range between £75.5-£128.9 million. CFS/ME incurs huge productivity costs amongst the small fraction of adults with CFS/ME who access specialist services.

Risk of relapse after antidepressant discontinuation in anxiety disorders, obsessive-compulsive disorder, and post-traumatic stress disorder: systematic review and meta-analysis of relapse prevention trials.

PubMed

Batelaan, Neeltje M; Bosman, Renske C; Muntingh, Anna; Scholten, Willemijn D; Huijbregts, Klaas M; van Balkom, Anton J L M

2017-09-13

Objectives  To examine the risk of relapse and time to relapse after discontinuation of antidepressants in patients with anxiety disorder who responded to antidepressants, and to explore whether relapse risk is related to type of anxiety disorder, type of antidepressant, mode of discontinuation, duration of treatment and follow-up, comorbidity, and allowance of psychotherapy. Design  Systematic review and meta-analyses of relapse prevention trials. Data sources  PubMed, Cochrane, Embase, and clinical trial registers (from inception to July 2016). Study selection  Eligible studies included patients with anxiety disorder who responded to antidepressants, randomised patients double blind to either continuing antidepressants or switching to placebo, and compared relapse rates or time to relapse. Data extraction  Two independent raters selected studies and extracted data. Random effect models were used to estimate odds ratios for relapse, hazard ratios for time to relapse, and relapse prevalence per group. The effect of various categorical and continuous variables was explored with subgroup analyses and meta-regression analyses respectively. Bias was assessed using the Cochrane tool. Results  The meta-analysis included 28 studies (n=5233) examining relapse with a maximum follow-up of one year. Across studies, risk of bias was considered low. Discontinuation increased the odds of relapse compared with continuing antidepressants (summary odds ratio 3.11, 95% confidence interval 2.48 to 3.89). Subgroup analyses and meta-regression analyses showed no statistical significance. Time to relapse (n=3002) was shorter when antidepressants were discontinued (summary hazard ratio 3.63, 2.58 to 5.10; n=11 studies). Summary relapse prevalences were 36.4% (30.8% to 42.1%; n=28 studies) for the placebo group and 16.4% (12.6% to 20.1%; n=28 studies) for the antidepressant group, but prevalence varied considerably across studies, most likely owing to differences in the length of follow-up. Dropout was higher in the placebo group (summary odds ratio 1.31, 1.06 to 1.63; n=27 studies). Conclusions  Up to one year of follow-up, discontinuation of antidepressant treatment results in higher relapse rates among responders compared with treatment continuation. The lack of evidence after a one year period should not be interpreted as explicit advice to discontinue antidepressants after one year. Given the chronicity of anxiety disorders, treatment should be directed by long term considerations, including relapse prevalence, side effects, and patients' preferences. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Failure Analysis of Alumina Reinforced Aluminum Microtruss and Tube Composites

NASA Astrophysics Data System (ADS)

Chien, Hsueh Fen (Karen)

The energy absorption capacity of cellular materials can be dramatically increased by applying a structural coating. This thesis examined the failure mechanisms of alumina reinforced 3003 aluminum alloy microtrusses and tubes. Alumina coatings were produced by hard anodizing and by plasma electrolytic oxidation (PEO). The relatively thin and discontinuous oxide coating at the hinge acted as a localized weak spot which triggered a chain reaction of failure, including oxide fracture, oxide spallation, oxide penetration to the aluminum core and severe local plastic deformation of the core. For the PEO microtrusses, delamination occurred within the oxide coating resulting in a global strut buckling failure mode. A new failure mode for the anodized tubes was observed: (i) axisymmetric folding of the aluminum core, (ii) longitudinal fracture, and (iii) alumina pulverization. Overall, the alumina coating enhanced the buckling resistance of the composites, while the aluminum core supported the oxide during the damage propagation.

Outer planets mission television subsystem optics study

NASA Technical Reports Server (NTRS)

1972-01-01

An optics study was performed to establish a candidate optical system design for the proposed NASA Mariner Jupiter/Saturn 77 mission. The study was performed over the 6-month period from January through June 1972. The candidate optical system contains both a wide angle (A) and a narrow angle (B) lens. An additional feature is a transfer mirror mechanism that allows image transfer from the B lens to the vidicon initially used for the A lens. This feature adds an operational redundancy to the optical system in allowing for narrow angle viewing if the narrow angle vidicon were to fail. In this failure mode, photography in the wide angle mode would be discontinued. The structure of the candidate system consists mainly of aluminum with substructures of Invar for athermalization. The total optical system weighs (excluding vidicons) approximately 30 pounds and has overall dimensions of 26.6 by 19.5 by 12.3 inches.

Modelling, analyses and design of switching converters

NASA Technical Reports Server (NTRS)

Cuk, S. M.; Middlebrook, R. D.

1978-01-01

A state-space averaging method for modelling switching dc-to-dc converters for both continuous and discontinuous conduction mode is developed. In each case the starting point is the unified state-space representation, and the end result is a complete linear circuit model, for each conduction mode, which correctly represents all essential features, namely, the input, output, and transfer properties (static dc as well as dynamic ac small-signal). While the method is generally applicable to any switching converter, it is extensively illustrated for the three common power stages (buck, boost, and buck-boost). The results for these converters are then easily tabulated owing to the fixed equivalent circuit topology of their canonical circuit model. The insights that emerge from the general state-space modelling approach lead to the design of new converter topologies through the study of generic properties of the cascade connection of basic buck and boost converters.

Preliminary acclimation strategies for successful startup in conventional biofilters.

PubMed

Elías, Ana; Barona, Astrid; Gallastegi, Gorka; Rojo, Naiara; Gurtubay, Luis; Ibarra-Berastegi, Gabriel

2010-08-01

The question of how to obtain the best inocula for conventional biofilters arises when an acclimation/adaptation procedure is to be applied. Bearing in mind that no standardized procedure for acclimating inocula exists, certain preliminary strategies for obtaining an active inoculum from wastewater treatment sludge are proposed in this work. Toluene was the contaminant to be degraded. Concerning the prior separation of sludge phases, no obvious advantage was found in separating the supernatant phase of the sludge before acclimation. As far as a continuous or discontinuous acclimation mode is concerned, the latter is recommended for rapidly obtaining acclimated sludge samples by operating the system for no longer than 1 month. The continuous mode rendered similar degradation rates, although it required longer operating time. Nevertheless, the great advantage of the continuous system lay in the absence of daily maintenance and the ready availability of the activated sample.

On the Theory and Numerical Simulation of Cohesive Crack Propagation with Application to Fiber-Reinforced Composites

NASA Technical Reports Server (NTRS)

Rudraraju, Siva Shankar; Garikipati, Krishna; Waas, Anthony M.; Bednarcyk, Brett A.

2013-01-01

The phenomenon of crack propagation is among the predominant modes of failure in many natural and engineering structures, often leading to severe loss of structural integrity and catastrophic failure. Thus, the ability to understand and a priori simulate the evolution of this failure mode has been one of the cornerstones of applied mechanics and structural engineering and is broadly referred to as "fracture mechanics." The work reported herein focuses on extending this understanding, in the context of through-thickness crack propagation in cohesive materials, through the development of a continuum-level multiscale numerical framework, which represents cracks as displacement discontinuities across a surface of zero measure. This report presents the relevant theory, mathematical framework, numerical modeling, and experimental investigations of through-thickness crack propagation in fiber-reinforced composites using the Variational Multiscale Cohesive Method (VMCM) developed by the authors.

Memantine improves buprenorphine/naloxone treatment for opioid dependent young adults.

PubMed

Gonzalez, Gerardo; DiGirolamo, Gregory; Romero-Gonzalez, Mauricio; Smelson, David; Ziedonis, Douglas; Kolodziej, Monika

2015-11-01

Opioid use disorders are considered a serious public health problem among young adults. Current treatment is limited to long-term opioid substitution therapy, with high relapse rates after discontinuation. This study evaluated the co-administration of memantine to brief buprenorphine pharmacotherapy as a treatment alternative. 13-week double-blind placebo-controlled trial evaluating 80 young adult opioid dependent participants treated with buprenorphine/naloxone 16-4mg/day and randomized to memantine (15mg or 30mg) or placebo. Primary outcomes were a change in the weekly mean proportion of opioid use, and cumulative abstinence rates after rapid buprenorphine discontinuation on week 9. Treatment retention was not significantly different between groups. The memantine 30mg group was significantly less likely to relapse and to use opioids after buprenorphine discontinuation. Among participants abstinent on week 8, those in the memantine 30mg group (81.9%) were significantly less likely to relapse after buprenorphine was discontinued compared to the placebo group (30%) (p<0.025). Also, the memantine 30mg group had significantly reduced opioid use (mean=0, SEM±0.00) compared to the placebo group (mean=0.33, SEM±0.35; p<0.004) during the last 2 weeks of study participation. Memantine 30mg significantly improved short-term treatment with buprenorphine/naloxone for opioid dependent young adults by reducing relapse and opioid use after buprenorphine discontinuation. Combined short-term treatment with buprenorphine/naloxone may be an effective alternative treatment to long-term methadone or buprenorphine maintenance in young adults. Published by Elsevier Ireland Ltd.

SUPRATHERMAL ELECTRON STRAHL WIDTHS IN THE PRESENCE OF NARROW-BAND WHISTLER WAVES IN THE SOLAR WIND

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kajdič, P.; Alexandrova, O.; Maksimovic, M.

2016-12-20

We perform the first statistical study of the effects of the interaction of suprathermal electrons with narrow-band whistler mode waves in the solar wind (SW). We show that this interaction does occur and that it is associated with enhanced widths of the so-called strahl component. The latter is directed along the interplanetary magnetic field away from the Sun. We do the study by comparing the strahl pitch angle widths in the SW at 1 AU in the absence of large scale discontinuities and transient structures, such as interplanetary shocks, interplanetary coronal mass ejections, stream interaction regions, etc. during times whenmore » the whistler mode waves were present and when they were absent. This is done by using the data from two Cluster instruments: Spatio Temporal Analysis of Field Fluctuations experiment (STAFF) data in the frequency range between ∼0.1 and ∼200 Hz were used for determining the wave properties and Plasma Electron And Current Experiment (PEACE) data sets at 12 central energies between ∼57 eV (equivalent to ∼10 typical electron thermal energies in the SW, E{sub T}) and ∼676 eV (∼113 E{sub T}) for pitch angle measurements. Statistical analysis shows that, during the intervals with the whistler waves, the strahl component on average exhibits pitch angle widths between 2° and 12° larger than during the intervals when these waves are not present. The largest difference is obtained for the electron central energy of ∼344 eV (∼57 ET).« less

Semi-analytical discontinuous Galerkin finite element method for the calculation of dispersion properties of guided waves in plates.

PubMed

Hebaz, Salah-Eddine; Benmeddour, Farouk; Moulin, Emmanuel; Assaad, Jamal

2018-01-01

The development of reliable guided waves inspection systems is conditioned by an accurate knowledge of their dispersive properties. The semi-analytical finite element method has been proven to be very practical for modeling wave propagation in arbitrary cross-section waveguides. However, when it comes to computations on complex geometries to a given accuracy, it still has a major drawback: the high consumption of resources. Recently, discontinuous Galerkin finite element method (DG-FEM) has been found advantageous over the standard finite element method when applied as well in the frequency domain. In this work, a high-order method for the computation of Lamb mode characteristics in plates is proposed. The problem is discretised using a class of DG-FEM, namely, the interior penalty methods family. The analytical validation is performed through the homogeneous isotropic case with traction-free boundary conditions. Afterwards, functionally graded material plates are analysed and a numerical example is presented. It was found that the obtained results are in good agreement with those found in the literature.

Influence of helical external driven current on nonlinear resistive tearing mode evolution and saturation in tokamaks

NASA Astrophysics Data System (ADS)

Zhang, W.; Wang, S.; Ma, Z. W.

2017-06-01

The influences of helical driven currents on nonlinear resistive tearing mode evolution and saturation are studied by using a three-dimensional toroidal resistive magnetohydrodynamic code (CLT). We carried out three types of helical driven currents: stationary, time-dependent amplitude, and thickness. It is found that the helical driven current is much more efficient than the Gaussian driven current used in our previous study [S. Wang et al., Phys. Plasmas 23(5), 052503 (2016)]. The stationary helical driven current cannot persistently control tearing mode instabilities. For the time-dependent helical driven current with f c d = 0.01 and δ c d < 0.04 , the island size can be reduced to its saturated level that is about one third of the initial island size. However, if the total driven current increases to about 7% of the total plasma current, tearing mode instabilities will rebound again due to the excitation of the triple tearing mode. For the helical driven current with time dependent strength and thickness, the reduction speed of the radial perturbation component of the magnetic field increases with an increase in the driven current and then saturates at a quite low level. The tearing mode is always controlled even for a large driven current.

Blue Again: Perturbational Effects of Antidepressants Suggest Monoaminergic Homeostasis in Major Depression

PubMed Central

Andrews, Paul W.; Kornstein, Susan G.; Halberstadt, Lisa J.; Gardner, Charles O.; Neale, Michael C.

2011-01-01

Some evolutionary researchers have argued that current diagnostic criteria for major depressive disorder (MDD) may not accurately distinguish true instances of disorder from a normal, adaptive stress response. According to disorder advocates, neurochemicals like the monoamine neurotransmitters (serotonin, norepinephrine, and dopamine) are dysregulated in major depression. Monoamines are normally under homeostatic control, so the monoamine disorder hypothesis implies a breakdown in homeostatic mechanisms. In contrast, adaptationist hypotheses propose that homeostatic mechanisms are properly functioning in most patients meeting current criteria for MDD. If the homeostatic mechanisms regulating monoamines are functioning properly in these patients, then oppositional tolerance should develop with prolonged antidepressant medication (ADM) therapy. Oppositional tolerance refers to the forces that develop when a homeostatic mechanism has been subject to prolonged pharmacological perturbation that attempt to bring the system back to equilibrium. When pharmacological intervention is discontinued, the oppositional forces cause monoamine levels to overshoot their equilibrium levels. Since depressive symptoms are under monoaminergic control, this overshoot should cause a resurgence of depressive symptoms that is proportional to the perturbational effect of the ADM. We test this prediction by conducting a meta-analysis of ADM discontinuation studies. We find that the risk of relapse after ADM discontinuation is positively associated with the degree to which ADMs enhance serotonin and norepinephrine in prefrontal cortex, after controlling for covariates. The results are consistent with oppositional tolerance, and provide no evidence of malfunction in the monoaminergic regulatory mechanisms in patients meeting current diagnostic criteria for MDD. We discuss the evolutionary and clinical implications of our findings. PMID:21779273

Strain energy release rate analysis of delamination in a tapered laminate subjected to tension load

NASA Technical Reports Server (NTRS)

Salpekar, S. A.; Raju, I. S.; Obrien, T. K.

1990-01-01

A tapered composite laminate subjected to tension load was analyzed using the finite-element method. The glass/epoxy laminate has a (+ or - 45)sub 3 group of plies dropped in three distinct steps, each 20 ply-thicknesses apart, thus forming a taper angle of 5.71 degrees. Steep gradients of interlaminar normal and shear stress on a potential delamination interface suggest the existence of stress singularities at the points of material and geometric discontinuities created by the internal plydrops. The delamination was assumed to initiate at the thin end of the taper on a -45/+45 interface and the delamination growth was simulated in both directions, i.e., along the taper and into the thin region. The strain-energy-release rate for a delamination growing into the thin laminate consisted predominantly of mode I (opening) component. For a delamination growing along the tapered region, the strain-energy-release rate was initially all mode I, but the proportion of mode I decreased with increase in delamination size until eventually total G was all mode II. The total G for both delamination tips increased with increase in delamination size, indicating that a delamination initiating at the end of the taper will grow unstably along the taper and into the thin laminate simultaneously.

Peridynamics for failure and residual strength prediction of fiber-reinforced composites

NASA Astrophysics Data System (ADS)

Colavito, Kyle

Peridynamics is a reformulation of classical continuum mechanics that utilizes integral equations in place of partial differential equations to remove the difficulty in handling discontinuities, such as cracks or interfaces, within a body. Damage is included within the constitutive model; initiation and propagation can occur without resorting to special crack growth criteria necessary in other commonly utilized approaches. Predicting damage and residual strengths of composite materials involves capturing complex, distinct and progressive failure modes. The peridynamic laminate theory correctly predicts the load redistribution in general laminate layups in the presence of complex failure modes through the use of multiple interaction types. This study presents two approaches to obtain the critical peridynamic failure parameters necessary to capture the residual strength of a composite structure. The validity of both approaches is first demonstrated by considering the residual strength of isotropic materials. The peridynamic theory is used to predict the crack growth and final failure load in both a diagonally loaded square plate with a center crack, as well as a four-point shear specimen subjected to asymmetric loading. This study also establishes the validity of each approach by considering composite laminate specimens in which each failure mode is isolated. Finally, the failure loads and final failure modes are predicted in a laminate with various hole diameters subjected to tensile and compressive loads.

A discontinuous Galerkin method for poroelastic wave propagation: The two-dimensional case

NASA Astrophysics Data System (ADS)

Dudley Ward, N. F.; Lähivaara, T.; Eveson, S.

2017-12-01

In this paper, we consider a high-order discontinuous Galerkin (DG) method for modelling wave propagation in coupled poroelastic-elastic media. The upwind numerical flux is derived as an exact solution for the Riemann problem including the poroelastic-elastic interface. Attenuation mechanisms in both Biot's low- and high-frequency regimes are considered. The current implementation supports non-uniform basis orders which can be used to control the numerical accuracy element by element. In the numerical examples, we study the convergence properties of the proposed DG scheme and provide experiments where the numerical accuracy of the scheme under consideration is compared to analytic and other numerical solutions.

The Impact of Discontinuity Front Orientation on the Accuracy of L1 Space Weather Forecasting

NASA Astrophysics Data System (ADS)

Szabo, A.

2013-12-01

Current space weather forecasting from the Sun-Earth first Lagrange (L1) point assumes that all observed solar wind discontinuity fronts (interplanetary shocks, ICME boundaries) are perpendicular to the Sun-Earth line and are propagating radially out from eh Sun. In reality, these weather fronts can have significantly tilted orientation. Combined ACE, Wind and Soho observations allow the quantification of this effect. With the launch of the DSCOVR spacecraft in early 2015, dual real-time solar wind measurements will become available (at least at some time). Algorithms and their impact exploiting this unique scenario will be discussed.

METHOD DEVELOPMENT, EVALUATION, REFINEMENT, AND ANALYSIS FOR FIELD STUDIES

EPA Science Inventory

Manufacturers routinely introduce new pesticides into the marketplace and discontinue manufacturing older pesticides that may be more toxic to humans. Analytical methods and environmental data are needed for current use residential pesticides (e.g., pyrethrins, synthetic pyrethr...

Electron cyclotron resonance plasma production by using pulse mode microwaves and dependences of ion beam current and plasma parameters on the pulse condition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiriyama, Ryutaro; Takenaka, Tomoya; Kurisu, Yousuke

2012-02-15

We measure the ion beam current and the plasma parameters by using the pulse mode microwave operation in the first stage of a tandem type ECRIS. The time averaged extracted ion beam current in the pulse mode operation is larger than that of the cw mode operation with the same averaged microwave power. The electron density n{sub e} in the pulse mode is higher and the electron temperature T{sub e} is lower than those of the cw mode operation. These plasma parameters are considered to cause in the increase of the ion beam current and are suitable to produce molecularmore » or cluster ions.« less

Single Active Switch PV Inverter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramanan, V. R.; Pan, Zhiguo

This report presents a new PV inverter topology that uses only one active switch instead of 7 active switches in a conventional PV inverter. It has a buck boost converter and operates at discontinuous current control mode, which can reduce the output stage from an active switch bridge to a thyristor bridge. This concept, if successfully demonstrated, may have great cost and size/weight benefits over conventional solutions. Since the proposed topology is completely different from the traditional boost converter plus voltage source inverter approach, there is no existing control/modulation scheme available. A new modulation scheme for both the main switchmore » and the thyristors has been developed. An active clamping circuit has also been proposed to reduce switching losses and voltage spike during the switching transient. A simulation model has been set up to validate the control algorithm and clamping circuit. Simulated results show that a proposed 10 kW PV inverter can reach 5% total harmonic distortion (THD), 98.8% peak efficiency with only one main active switch, and an inductor weighing less than 3 kg. Based on that, a 10 kW prototype converter has been designed and built.« less

Discharge current modes of high power impulse magnetron sputtering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Zhongzhen, E-mail: wuzz@pkusz.edu.cn; Xiao, Shu; Ma, Zhengyong

2015-09-15

Based on the production and disappearance of ions and electrons in the high power impulse magnetron sputtering plasma near the target, the expression of the discharge current is derived. Depending on the slope, six possible modes are deduced for the discharge current and the feasibility of each mode is discussed. The discharge parameters and target properties are simplified into the discharge voltage, sputtering yield, and ionization energy which mainly affect the discharge plasma. The relationship between these factors and the discharge current modes is also investigated.

The dating and interpretation of a Mode 1 site in the Luangwa Valley, Zambia.

PubMed

Barham, Lawrence; Phillips, William M; Maher, Barbara A; Karloukovski, Vassil; Duller, Geoff A T; Jain, Mayank; Wintle, Ann G

2011-05-01

Flake based assemblages (Mode 1) comprise the earliest stone technologies known, with well-dated Oldowan sites occurring in eastern Africa between ~2.6-1.7 Ma, and in less securely dated contexts in central, southern and northern Africa. Our understanding of the spread and local development of this technology outside East Africa remains hampered by the lack of reliable numerical dating techniques applicable to non-volcanic deposits. This study applied the still relatively new technique of cosmogenic nuclide burial dating ((10)Be/(26)Al) to calculate burial ages for fluvial gravels containing Mode 1 artefacts in the Luangwa Valley, Zambia. The Manzi River, a tributary of the Luangwa River, has exposed a 4.7 m deep section of fluvial sands with discontinuous but stratified gravel layers bearing Mode 1, possibly Oldowan, artefacts in the basal layers. An unconformity divides the Manzi section, separating Mode 1 deposits from overlying gravels containing Mode 3 (Middle Stone Age) artefacts. No diagnostic Mode 2 (Acheulean) artefacts were found. Cosmogenic nuclide burial dating was attempted for the basal gravels as well as exposure ages for the upper Mode 3 gravels, but was unsuccessful. The complex depositional history of the site prevented the calculation of reliable age models. A relative chronology for the full Manzi sequence was constructed, however, from the magnetostratigraphy of the deposit (N>R>N sequence). Isothermal thermoluminescence (ITL) dating of the upper Mode 3 layers also provided consistent results (~78 ka). A coarse but chronologically coherent sequence now exists for the Manzi section with the unconformity separating probable mid- or early Pleistocene deposits below from late Pleistocene deposits above. The results suggest Mode 1 technology in the Luangwa Valley may post-date the Oldowan in eastern and southern Africa. The dating programme has contributed to a clearer understanding of the geomorphological processes that have shaped the valley and structured its archaeological record. Copyright © 2010 Elsevier Ltd. All rights reserved.

The dating and interpretation of a Mode 1 site in the Luangwa Valley, Zambia

USGS Publications Warehouse

Barham, L.; Phillips, W.M.; Maher, B.A.; Karloukovski, V.; Duller, G.A.T.; Jain, M.; Wintle, A.G.

2011-01-01

Flake based assemblages (Mode 1) comprise the earliest stone technologies known, with well-dated Oldowan sites occurring in eastern Africa between ??? 2.6-1.7 Ma, and in less securely dated contexts in central, southern and northern Africa. Our understanding of the spread and local development of this technology outside East Africa remains hampered by the lack of reliable numerical dating techniques applicable to non-volcanic deposits. This study applied the still relatively new technique of cosmogenic nuclide burial dating (10Be/26Al) to calculate burial ages for fluvial gravels containing Mode 1 artefacts in the Luangwa Valley, Zambia. The Manzi River, a tributary of the Luangwa River, has exposed a 4.7 m deep section of fluvial sands with discontinuous but stratified gravel layers bearing Mode 1, possibly Oldowan, artefacts in the basal layers. An unconformity divides the Manzi section, separating Mode 1 deposits from overlying gravels containing Mode 3 (Middle Stone Age) artefacts. No diagnostic Mode 2 (Acheulean) artefacts were found. Cosmogenic nuclide burial dating was attempted for the basal gravels as well as exposure ages for the upper Mode 3 gravels, but was unsuccessful. The complex depositional history of the site prevented the calculation of reliable age models. A relative chronology for the full Manzi sequence was constructed, however, from the magnetostratigraphy of the deposit (N>R>N sequence). Isothermal thermoluminescence (ITL) dating of the upper Mode 3 layers also provided consistent results (???78 ka). A coarse but chronologically coherent sequence now exists for the Manzi section with the unconformity separating probable mid- or early Pleistocene deposits below from late Pleistocene deposits above. The results suggest Mode 1 technology in the Luangwa Valley may post-date the Oldowan in eastern and southern Africa. The dating programme has contributed to a clearer understanding of the geomorphological processes that have shaped the valley and structured its archaeological record. ?? 2010 Elsevier Ltd.

HBT-EP Program: MHD Dynamics and Active Control through 3D Fields and Currents

NASA Astrophysics Data System (ADS)

Navratil, G. A.; Bialek, J.; Brooks, J. W.; Byrne, P. J.; Desanto, S.; Levesque, J. P.; Mauel, M. E.; Stewart, I. G.; Hansen, C. J.

2017-10-01

The HBT-EP active mode control research program aims to: (i) advance understanding of the effects of 3D shaping on advanced tokamak fusion performance, (ii) resolve important MHD issues associated with disruptions, and (iii) measure and mitigate the effects of 3D scrape-off layer (SOL) currents through active and passive control of the plasma edge and conducting boundary structures. Comparison of kink mode structure and RMP response in circular versus diverted plasmas shows good agreement with DCON modeling. SOL current measurements have been used to study SOL current dynamics and current-sharing with the vacuum vessel wall during kink-mode growth and disruptions. A multi-chord extreme UV/soft X-ray array is being installed to provide detailed internal mode structure information. Internal local electrodes were used to apply local bias voltage at two radial locations to study the effect of rotation profile on MHD mode rotation and stability and radial current flow through the SOL. A GPU-based low latency control system using 96 inputs and 64 outputs to apply magnetic perturbations for active control of kink modes is extended to directly control the SOL currents for kink-mode control. An extensive array of SOL current monitors and edge drive electrodes are being installed for pioneering studies of helical edge current control. Supported by U.S. DOE Grant DE-FG02-86ER53222.

Development of the Nonhydrostatic Unified Model of the Atmosphere (NUMA): Limited-Area Mode (Preprint)

DTIC Science & Technology

2011-04-14

such that qN(x, t ) = MN ∑ j =1 qj( t )ψj(x) (9) 6 whereMN = (N+1) 3 is the number of nodes per element andN is the order of the basis functions. The...M.H. Mawson , A. Staniforth, A.A. White, N. Wood, A new dynamical core for the Met Office’s global and regional modelling of the atmosphere, Q. J . R...Tufo, M. Levy, T . Voran, Development of a scalable global discontinuous Galerkin atmospheric model, Int. J . of Comput. Sci. Eng. In Press (2008). [6

Onset of chaos in a single-phase power electronic inverter.

PubMed

Avrutin, Viktor; Mosekilde, Erik; Zhusubaliyev, Zhanybai T; Gardini, Laura

2015-04-01

Supported by experiments on a power electronic DC/AC converter, this paper considers an unusual transition from the domain of stable periodic dynamics (corresponding to the desired mode of operation) to chaotic dynamics. The behavior of the converter is studied by means of a 1D stroboscopic map derived from a non-autonomous ordinary differential equation with discontinuous right-hand side. By construction, this stroboscopic map has a high number of border points. It is shown that the onset of chaos occurs stepwise, via irregular cascades of different border collisions, some of which lead to bifurcations while others do not.

Finite-time stabilization of chaotic gyros based on a homogeneous supertwisting-like algorithm

NASA Astrophysics Data System (ADS)

Khamsuwan, Pitcha; Sangpet, Teerawat; Kuntanapreeda, Suwat

2018-01-01

This paper presents a finite-time stabilization scheme for nonlinear chaotic gyros. The scheme utilizes a supertwisting-like continuous control algorithm for the systems of dimension more than one with a Lipschitz disturbance. The algorithm yields finite-time convergence similar to that produces by discontinuous sliding mode control algorithms. To design the controller, the nonlinearities in the gyro are treated as a disturbance in the system. Thanks to the dissipativeness of chaotic systems, the nonlinearities also possess the Lipschitz property. Numerical results are provided to illustrate the effectiveness of the scheme.

User interface to administrative DRMS within a distributed environment

NASA Technical Reports Server (NTRS)

Martin, L. D.; Kirk, R. D.

1983-01-01

The implementation of a data base management system (DBMS) into a communications office to control and report on communication leased service contracts is discussed. The system user executes online programs to update five files residing on a UNIVAC 1100/82, through the forms mode features of the Tektronix 4025 terminal and IMSAI 8080 microcomputer. This user can select the appropriate form to the Tektronix 4025 screen, and enter new data, update existing data, or discontinue service. Selective online printing of 40 reports is accomplished by the system user to satisfy management, budget, and bill payment reporting requirements.

A complete dc characterization of a constant-frequency, clamped-mode, series-resonant converter

NASA Technical Reports Server (NTRS)

Tsai, Fu-Sheng; Lee, Fred C.

1988-01-01

The dc behavior of a clamped-mode series-resonant converter is characterized systematically. Given a circuit operating condition, the converter's mode of operation is determined and various circuit parameters are calculated, such as average inductor current (load current), rms inductor current, peak capacitor voltage, rms switch currents, average diode currents, switch turn-on currents, and switch turn-off currents. Regions of operation are defined, and various circuit characteristics are derived to facilitate the converter design.

PrEP Uptake, Adherence, and Discontinuation among California YMSM Using Geosocial Networking Applications

PubMed Central

Holloway, Ian; Dougherty, Ryan; Gildner, Jennifer; Beougher, Sean C.; Pulsipher, Craig; Montoya, Jorge A.; Plant, Aaron; Leibowitz, Arleen

2016-01-01

We investigated PrEP uptake, adherence, and discontinuation among young app-using MSM in California (N=761). 9.7% of participants had ever used PrEP; 87% of those deemed good candidates for screening (indicated by a CDC risk index score ≥10) were not current or past users. PrEP use was associated with higher income (aOR:4.13; CI:1.87-9.12), receptive condomless anal sex(aOR:3.41; CI:1.71-6.78), HIV-positive sex partners (aOR:2.87; CI:1.53-5.38), popper use (aOR:3.47; CI:1.96-6.13), and recent STI diagnosis (aOR:2.90; CI:1.64-5.13). 41.5% of users wanted help remembering to take PrEP. The top reason for discontinuation was concern about long-term side effects (33.0%). YMSM app users are prime candidates for PrEP, despite low uptake. Apps may be useful tools for PrEP information dissemination, adherence monitoring, and support. PMID:27552158

Detection and Correction of Step Discontinuities in Kepler Flux Time Series

NASA Technical Reports Server (NTRS)

Kolodziejczak, J. J.; Morris, R. L.

2011-01-01

PDC 8.0 includes an implementation of a new algorithm to detect and correct step discontinuities appearing in roughly one of every 20 stellar light curves during a given quarter. The majority of such discontinuities are believed to result from high-energy particles (either cosmic or solar in origin) striking the photometer and causing permanent local changes (typically -0.5%) in quantum efficiency, though a partial exponential recovery is often observed [1]. Since these features, dubbed sudden pixel sensitivity dropouts (SPSDs), are uncorrelated across targets they cannot be properly accounted for by the current detrending algorithm. PDC detrending is based on the assumption that features in flux time series are due either to intrinsic stellar phenomena or to systematic errors and that systematics will exhibit measurable correlations across targets. SPSD events violate these assumptions and their successful removal not only rectifies the flux values of affected targets, but demonstrably improves the overall performance of PDC detrending [1].

Electro-Fenton as a feasible advanced treatment process to produce reclaimed water.

PubMed

Durán Moreno, A; Frontana-Uribe, B A; Ramírez Zamora, R M

2004-01-01

The feasibility of the electro-Fenton process to generate simultaneously both of the Fenton's reagent species (Fe2+/H2O2), was assessed as a potentially more economical alternative to the classical Fenton's reaction to produce reclaimed water. An air-saturated combined wastewater (mixture of municipal and laboratory effluents) was treated in discontinuous and continuous reactors at pH = 3.5. The discontinuous reactor was a 2 L electrochemical laboratory cell fitted with concentric graphite and iron electrodes. The continuous reactor tests used a pilot treatment system comprising the aforementioned electrochemical cell, two clarifiers and one sand filter. Several tests were carried out at different conditions of reaction time (0-60 min) and electrical current values (0.2-1.0 A) in the discontinuous reactor. The best operating conditions were 60 min and 1 A without filtration of effluents. At these conditions, in discontinuous and continuous reactors with filtration, the COD, turbidity and color removal were 65-74.8%, 77-92.3% and 80-100%, respectively. Fecal and total coliforms, Escherichia coli, Shigella and Salmonella sp. were not detected at the end of the pilot treatment system. Electrogeneration of the Fenton's reagent is also economical; its cost is one-fifth the cost reported for Advanced Primary Treatment.

Agarose electrophoresis of DNA in discontinuous buffers, using a horizontal slab apparatus and a buffer system with improved properties.

PubMed

Zsolnai, A; Orbán, L; Chrambach, A

1993-03-01

Using a horizontal slab apparatus with a buffer in the reservoirs at the level of the gel ("sea-level electrophoresis"), the retrograde discontinuous buffer system reported by Wiltfang et al. for sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) of proteins was applied to DNA electrophoresis. This application yielded the advantages of an increased displacement rate of the moving boundary front and a decrease in the concentration of the counterion base in the resolving phase, which yielded reduced relative mobility values at equivalent gel concentrations and practicable low buffer concentrations. The change of relative mobilities (Rf) with a variation of field strength is decreased compared to that of the migration rate in the continuous Tris-boric-acid-EDTA (TBE) buffer and thus the robustness of the system is improved, as well as the efficiency of separation. The system of Wiltfang et al. has in common with previously described discontinuous DNA system, that it is able to stack DNA from dilute samples and is insensitive to sample components with lower net mobilities than DNA, such as acetate. However, the variance of Rf at constant current density in the discontinuous buffer system is not improved over that of the migration rate at constant field strength in the continuous TBE buffer.

Evidence for frozen melts in the mid-lithosphere detected from active-source seismic data.

PubMed

Ohira, Akane; Kodaira, Shuichi; Nakamura, Yasuyuki; Fujie, Gou; Arai, Ryuta; Miura, Seiichi

2017-11-17

The interactions of the lithospheric plates that form the Earth's outer shell provide much of the evidentiary basis for modern plate tectonic theory. Seismic discontinuities in the lithosphere arising from mantle convection and plate motion provide constraints on the physical and chemical properties of the mantle that contribute to the processes of formation and evolution of tectonic plates. Seismological studies during the past two decades have detected seismic discontinuities within the oceanic lithosphere in addition to that at the lithosphere-asthenosphere boundary (LAB). However, the depth, distribution, and physical properties of these discontinuities are not well constrained, which makes it difficult to use seismological data to examine their origin. Here we present new active-source seismic data acquired along a 1,130 km profile across an old Pacific plate (148-128 Ma) that show oceanic mid-lithosphere discontinuities (oceanic MLDs) distributed 37-59 km below the seafloor. The presence of the oceanic MLDs suggests that frozen melts that accumulated at past LABs have been preserved as low-velocity layers within the current mature lithosphere. These observations show that long-offset, high-frequency, active-source seismic data can be used to image mid-lithospheric structure, which is fundamental to understanding the formation and evolution of tectonic plates.

Mode Transitions in Magnetically Shielded Hall Effect Thrusters

NASA Technical Reports Server (NTRS)

Sekerak, Michael J.; Longmier, Benjamin W.; Gallimore, Alec D.; Huang, Wensheng; Kamhawi, Hani; Hofer, Richard R.; Jorns, Benjamin A.; Polk, James E.

2014-01-01

A mode transition study is conducted in magnetically shielded thrusters where the magnetic field magnitude is varied to induce mode transitions. Three different oscillatory modes are identified with the 20-kW NASA-300MS-2 and the 6-kW H6MS: Mode 1) global mode similar to unshielded thrusters at low magnetic fields, Mode 2) cathode oscillations at nominal magnetic fields, and Mode 3) combined spoke, cathode and breathing mode oscillations at high magnetic fields. Mode 1 exhibits large amplitude, low frequency (1-10 kHz), breathing mode type oscillations where discharge current mean value and oscillation amplitude peak. The mean discharge current is minimized while thrust-to-power and anode efficiency are maximized in Mode 2, where higher frequency (50-90 kHz), low amplitude, cathode oscillations dominate. Thrust is maximized in Mode 3 and decreases by 5-6% with decreasing magnetic field strength. The presence or absence of spokes and strong cathode oscillations do not affect each other or discharge current. Similar to unshielded thrusters, mode transitions and plasma oscillations affect magnetically shielded thruster performance and should be characterized during system development.

MHD Wave Propagation at the Interface Between Solar Chromosphere and Corona

NASA Astrophysics Data System (ADS)

Huang, Y.; Song, P.; Vasyliunas, V. M.

2017-12-01

We study the electromagnetic and momentum constraints at the solar transition region which is a sharp layer interfacing between the solar chromosphere and corona. When mass transfer between the two domains is neglected, the transition region can be treated as a contact discontinuity across which the magnetic flux is conserved and the total forces are balanced. We consider an Alfvénic perturbation that propagates along the magnetic field incident onto the interface from one side. In order to satisfy the boundary conditions at the transition region, only part of the incident energy flux is transmitted through and the rest is reflected. Taking into account the highly anisotropic propagation of waves in magnetized plasmas, we generalize the law of reflection and specify Snell's law for each of the three wave MHD modes: incompressible Alfvén mode and compressible fast and slow modes. Unlike conventional optical systems, the interface between two magnetized plasmas is not rigid but can be deformed by the waves, allowing momentum and energy to be transferred by compression. With compressible modes included, the Fresnel conditions need substantial modification. We derive Fresnel conditions, reflectivities and transmittances, and mode conversion for incident waves propagating along the background magnetic field. The results are well organized when the incident perturbation is decomposed into components in and normal to the incident plane (containing the background magnetic field and the normal direction of the interface). For a perturbation normal to the incident plane, both transmitted and reflected perturbations are incompressible Alfvén mode waves. For a perturbation in the incident plane, they can be compressible slow and fast mode waves which may produce ripples on the transition region.

Investigation of the n  =  1 resistive wall modes in the ITER high-mode confinement

NASA Astrophysics Data System (ADS)

Zheng, L. J.; Kotschenreuther, M. T.; Valanju, P.

2017-06-01

The n  =  1 resistive wall mode (RWM) stability of ITER high-mode confinement is investigated with bootstrap current included for equilibrium, together with the rotation and diamagnetic drift effects for stability. Here, n is the toroidal mode number. We use the CORSICA code for computing the free boundary equilibrium and AEGIS code for stability. We find that the inclusion of bootstrap current for equilibrium is critical. It can reduce the local magnetic shear in the pedestal, so that the infernal mode branches can develop. Consequently, the n  =  1 modes become unstable without a stabilizing wall at a considerably lower beta limit, driven by the steep pressure gradient in the pedestal. Typical values of the wall position stabilize the ideal mode, but give rise to the ‘pedestal’ resistive wall modes. We find that the rotation can contribute a stabilizing effect on RWMs and the diamagnetic drift effects can further improve the stability in the co-current rotation case. But, generally speaking, the rotation stabilization effects are not as effective as the case without including the bootstrap current effects on equilibrium. We also find that the diamagnetic drift effects are actually destabilizing when there is a counter-current rotation.

Extreme interplanetary rotational discontinuities at 1 AU

NASA Astrophysics Data System (ADS)

Lepping, R. P.; Wu, C.-C.

2005-11-01

This study is concerned with the identification and description of a special subset of four Wind interplanetary rotational discontinuities (from an earlier study of 134 directional discontinuities by Lepping et al. (2003)) with some "extreme" characteristics, in the sense that every case has (1) an almost planar current sheet surface, (2) a very large discontinuity angle (ω), (3) at least moderately strong normal field components (>0.8 nT), and (4) the overall set has a very broad range of transition layer thicknesses, with one being as thick as 50 RE and another at the other extreme being 1.6 RE, most being much thicker than are usually studied. Each example has a well-determined surface normal (n) according to minimum variance analysis and corroborated via time delay checking of the discontinuity with observations at IMP 8 by employing the local surface planarity. From the variance analyses, most of these cases had unusually large ratios of intermediate-to-minimum eigenvalues (λI/λmin), being on average 32 for three cases (with a fourth being much larger), indicating compact current sheet transition zones, another (the fifth) extreme property. For many years there has been a controversy as to the relative distribution of rotational (RDs) to tangential discontinuities (TDs) in the solar wind at 1 AU (and elsewhere, such as between the Sun and Earth), even to the point where some authors have suggested that RDs with large ∣Bn∣s are probably not generated or, if generated, are unstable and therefore very rare. Some of this disagreement apparently has been due to the different selection criteria used, e.g., some allowed eigenvalue ratios (λI/λmin) to be almost an order of magnitude lower than 32 in estimating n, usually introducing unacceptable error in n and therefore also in ∣Bn∣. However, we suggest that RDs may not be so rare at 1 AU, but good quality cases (where ∣Bn∣ confidently exceeds the error in ∣Bn∣) appear to be uncommon, and further, cases of large ∣Bn∣ may indeed be rare. Finally, the issue of estimating the number of RDs-to-TDs was revisited using the full 134 events of the original Lepping et al. (2003) study (which utilized the RDs' propagation speeds for this estimation, an unconventional approach) but now by considering only normal field components, the more conventional approach. This resulted in slightly different conclusions, depending on specific assumptions used, making the unconventional approach suspect.

Malpractice Burden, Rural Location, and Discontinuation of Obstetric Care: A Study of Obstetric Providers in Michigan

PubMed Central

Xu, Xiao; Siefert, Kristine A.; Jacobson, Peter D.; Lori, Jody R.; Gueorguieva, Iana; Ransom, Scott B.

2011-01-01

Context It has long been a concern that professional liability problems disproportionately affect the delivery of obstetrical services to women living in rural areas. Michigan, a state with a large number of rural communities, is considered to be at risk for a medical liability crisis. Purpose This study examined whether higher malpractice burden on obstetric providers was associated with an increased likelihood of discontinuing obstetric care and whether there were rural-urban differences in the relationship. Methods Data on 500 obstetrician-gynecologists and family physicians who had provided obstetric care at some point in their career (either currently or previously) were obtained from a statewide survey in Michigan. Statistical tests and multivariate regression analyses were performed to examine the interrelationship among malpractice burden, rural location, and discontinuation of obstetric care. Findings After adjusting for other factors that might influence a physician’s decision about whether to stop obstetric care, our results showed no significant impact of malpractice burden on physicians’ likelihood to discontinue obstetric care. Rural-urban location of the practice did not modify the nature of this relationship. However, family physicians in rural Michigan had a nearly four fold higher likelihood of withdrawing obstetric care when compared to urban family physicians. Conclusions The higher likelihood of rural family physicians to discontinue obstetric care should be carefully weighed in future interventions to preserve obstetric care supply. More research is needed to better understand the practice environment of rural family physicians and the reasons for their withdrawal from obstetric care. PMID:19166559

Report: EPA’s Distribution of Superfund Human Resources Does Not Support Current Regional Workload

EPA Pesticide Factsheets

Report #17-P-0397, September 19, 2017. Due to insufficient human resources to cover all Superfund site work, some regions have had to slow down or discontinue their efforts to protect human health and the environment.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foltyn, Stephen R; Jia, Quanxi; Arendt, Paul N

A superconducting tape having reduced AC losses. The tape has a high temperature superconductor layer that is segmented. Disruptive strips, formed in one of the tape substrate, a buffer layer, and the superconducting layer create parallel discontinuities in the superconducting layer that separate the current-carrying elements of the superconducting layer into strips or filament-like structures. Segmentation of the current-carrying elements has the effect of reducing AC current losses. Methods of making such a superconducting tape and reducing AC losses in such tapes are also disclosed.

Influence of driven current on resistive tearing mode in Tokamaks

NASA Astrophysics Data System (ADS)

Ma, Zhiwei; Wang, Sheng; Zhang, Wei

2016-10-01

Influence of driven current on the m / n = 2 / 1 resistive tearing mode is studied systematically using a three-dimensional toroidal MHD code (CLT). A uniform driven current with Gaussian distribution in the radial direction is imposed around the unperturbed rational surface. It is found that the driven current can locally modify the profiles of the current and safety factor, such that the tearing mode becomes linearly stable. The stabilizing effect increases with increase of the driven current Icd or decrease of its width δcd, unless an excessively large driven current reverses the magnetic shear near the rational surface and drives other instabilities such as double or triple tearing modes. The stabilizing effect can be negligible or becomes reversed if the maximum driven current density is not at the unperturbed rational surface. ITER-CN Program.

Sharp inflaton potentials and bi-spectra: effects of smoothening the discontinuity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, Jérôme; Sriramkumar, L.; Hazra, Dhiraj Kumar, E-mail: jmartin@iap.fr, E-mail: sriram@physics.iitm.ac.in, E-mail: dhiraj@apctp.org

Sharp shapes in the inflaton potentials often lead to short departures from slow roll which, in turn, result in deviations from scale invariance in the scalar power spectrum. Typically, in such situations, the scalar power spectrum exhibits a burst of features associated with modes that leave the Hubble radius either immediately before or during the epoch of fast roll. Moreover, one also finds that the power spectrum turns scale invariant at smaller scales corresponding to modes that leave the Hubble radius at later stages, when slow roll has been restored. In other words, the imprints of brief departures from slowmore » roll, arising out of sharp shapes in the inflaton potential, are usually of a finite width in the scalar power spectrum. Intuitively, one may imagine that the scalar bi-spectrum too may exhibit a similar behavior, i.e. a restoration of scale invariance at small scales, when slow roll has been reestablished. However, in the case of the Starobinsky model (viz. the model described by a linear inflaton potential with a sudden change in its slope) involving the canonical scalar field, it has been found that, a rather sharp, though short, departure from slow roll can leave a lasting and significant imprint on the bi-spectrum. The bi-spectrum in this case is found to grow linearly with the wavenumber at small scales, a behavior which is clearly unphysical. In this work, we study the effects of smoothening the discontinuity in the Starobinsky model on the scalar bi-spectrum. Focusing on the equilateral limit, we analytically show that, for smoother potentials, the bi-spectrum indeed turns scale invariant at suitably large wavenumbers. We also confirm the analytical results numerically using our newly developed code BINGO. We conclude with a few comments on certain related points.« less

Elasticity of plagioclase feldspars

NASA Astrophysics Data System (ADS)

Brown, J. Michael; Angel, Ross J.; Ross, Nancy L.

2016-02-01

Elastic properties are reported for eight plagioclase feldspars that span compositions from albite (NaSi3AlO8) to anorthite (CaSi2Al2O8). Surface acoustic wave velocities measured using Impulsive Stimulated Light Scattering and compliance sums from high-pressure X-ray compression studies accurately determine all 21 components of the elasticity tensor for these triclinic minerals. The overall pattern of elasticity and the changes in individual elastic components with composition can be rationalized on the basis of the evolution of crystal structures and chemistry across this solid-solution join. All plagioclase feldspars have high elastic anisotropy; a* (the direction perpendicular to the b and c axes) is the softest direction by a factor of 3 in albite. From albite to anorthite the stiffness of this direction undergoes the greatest change, increasing twofold. Small discontinuities in the elastic components, inferred to occur between the three plagioclase phases with distinct symmetry (C1>¯, I1>¯, and P1>¯), appear consistent with the nature of the underlying conformation of the framework-linked tetrahedra and the associated structural changes. Measured body wave velocities of plagioclase-rich rocks, reported over the last five decades, are consistent with calculated Hill-averaged velocities using the current moduli. This confirms long-standing speculation that previously reported elastic moduli for plagioclase feldspars are systematically in error. The current results provide greater assurance that the seismic structure of the middle and lower crusts can be accurately estimated on the basis of specified mineral modes, chemistry, and fabric.

Project WILAS: Seismic imaging of crustal and upper mantle structures beneath the western Iberian Peninsula by means of the receiver-function technique

NASA Astrophysics Data System (ADS)

Dündar, Süleyman; Dias, Nuno A.; Silveira, Graça; Vinnik, Lev; Haberland, Christian

2013-04-01

An accurate knowledge of the structure of the earth's interior is of great importance to our understanding of tectonic processes. The WILAS-project (REF: PTDC/CTE-GIX/097946/2008) is a three-year collaborative project developed to study the subsurface structure of the western Iberian Peninsula, putting the main emphases on the lithosphere-asthenosphere system beneath the mainland of Portugal. The tectonic evolution of the target area has been driven by major plate-tectonic processes such as the historical opening of the Central Atlantic and the subsequent African-Eurasian convergence. Still, very little is known about the spatial structure of the continental collision. Within the framework of this research, a temporary network of 30 broadband three-component digital stations was operated between 2010 and 2012 in the target area. To carry out a large-scale structural analysis and facilitate a dense station-coverage for the area under investigation, the permanent Global Seismic Network stations, and temporary broadband stations deployed within the scope of the several seismic experiments (e.g. Doctar Network, Portuguese National Seismic Network), were included in the research analysis. In doing so, an unprecedented volume of high-quality data of a ca. 60X60 km density along with a combined network of 65 temporary and permanent broadband seismic stations are currently available for research purposes. One of the tasks of the WILAS research project has been a study of seismic velocity discontinuities beneath the western Iberian Peninsula region, up to a depth range of 700 km, utilizing the P- and S-receiver function techniques (PRF, SRF). Both techniques are based mainly on mode conversion of the elastic body-waves at an interface dividing the layers with different elastic properties. In the first phase of the project, PRF analysis was conducted in order to image the crust-mantle interface (Moho) and the mantle-transition-zone discontinuities at a depth of 410 km and 660 km beneath the area under investigation. While applying the common data processing steps (e.g., rotation, deconvolution and moveout-correction) to the selected data-set, we were able to create approximately 4.500 PRFs. The signals from the Moho, 410-km and 660-km discontinuities are clearly visible in many PRF stacks. The Moho depth range is from 26 to 34 km, with an average value of 29 km. No significant lateral variations in the depths of the "410-km" and "660-km" discontinuities have been identified so far. In the second phase of this project, the S-receiver-function technique will be applied in order to map the thickness of the underlying mantle lithosphere. Additionally, joint inversion of PRFs and waveforms of SKS will be used to investigate depth-localized azimuthal anisotropy and the related past and present mantle flows.

On the application of frequency selective common mode feedback for multifrequency EIT.

PubMed

Langlois, Peter J; Wu, Yu; Bayford, Richard H; Demosthenous, Andreas

2015-06-01

Common mode voltages are frequently a problem in electrical impedance tomography (EIT) and other bioimpedance applications. To reduce their amplitude common mode feedback is employed. Formalised analyses of both current and voltage feedback is presented in this paper for current drives. Common mode effects due to imbalances caused by the current drives, the electrode connections to the body load and the introduction of the body impedance to ground are considered. Frequency selective narrowband common mode feedback previously proposed to provide feedback stability is examined. As a step towards multifrequency applications the use of narrowband feedback is experimentally demonstrated for two simultaneous current drives. Measured results using standard available components show a reduction of 62 dB for current feedback and 31 dB for voltage feedback. Frequencies ranged from 50 kHz to 1 MHz.

EIGENMODES OF THREE-DIMENSIONAL MAGNETIC ARCADES IN THE SUN’S CORONA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hindman, Bradley W.; Jain, Rekha, E-mail: hindman@solarz.colorado.edu

We develop a model of coronal-loop oscillations that treats the observed bright loops as an integral part of a larger three-dimensional (3D) magnetic structure comprised of the entire magnetic arcade. We demonstrate that magnetic arcades within the solar corona can trap MHD fast waves in a 3D waveguide. This is accomplished through the construction of a cylindrically symmetric model of a magnetic arcade with a potential magnetic field. For a magnetically dominated plasma, we derive a governing equation for MHD fast waves and from this equation we show that the magnetic arcade forms a 3D waveguide if the Alfvén speedmore » increases monotonically beyond a fiducial radius. Both magnetic pressure and tension act as restoring forces, instead of just tension as is generally assumed in 1D models. Since magnetic pressure plays an important role, the eigenmodes involve propagation both parallel and transverse to the magnetic field. Using an analytic solution, we derive the specific eigenfrequencies and eigenfunctions for an arcade possessing a discontinuous density profile. The discontinuity separates a diffuse cylindrical cavity and an overlying shell of denser plasma that corresponds to the bright loops. We emphasize that all of the eigenfunctions have a discontinuous axial velocity at the density interface; hence, the interface can give rise to the Kelvin–Helmholtz instability. Further, we find that all modes have elliptical polarization with the degree of polarization changing with height. However, depending on the line of sight, only one polarization may be clearly visible.« less

Importance of Tensile Strength on the Shear Behavior of Discontinuities

NASA Astrophysics Data System (ADS)

Ghazvinian, A. H.; Azinfar, M. J.; Geranmayeh Vaneghi, R.

2012-05-01

In this study, the shear behavior of discontinuities possessing two different rock wall types with distinct separate compressive strengths was investigated. The designed profiles consisted of regular artificial joints molded by five types of plaster mortars, each representing a distinct uniaxial compressive strength. The compressive strengths of plaster specimens ranged from 5.9 to 19.5 MPa. These specimens were molded considering a regular triangular asperity profile and were designed so as to achieve joint walls with different strength material combinations. The results showed that the shear behavior of discontinuities possessing different joint wall compressive strengths (DDJCS) tested under constant normal load (CNL) conditions is the same as those possessing identical joint wall strengths, but the shear strength of DDJCS is governed by minor joint wall compressive strength. In addition, it was measured that the predicted values obtained by Barton's empirical criterion are greater than the experimental results. The finding indicates that there is a correlation between the joint roughness coefficient (JRC), normal stress, and mechanical strength. It was observed that the mode of failure of asperities is either pure tensile, pure shear, or a combination of both. Therefore, Barton's strength criterion, which considers the compressive strength of joint walls, was modified by substituting the compressive strength with the tensile strength. The validity of the modified criterion was examined by the comparison of the predicted shear values with the laboratory shear test results reported by Grasselli (Ph.D. thesis n.2404, Civil Engineering Department, EPFL, Lausanne, Switzerland, 2001). These comparisons infer that the modified criterion can predict the shear strength of joints more precisely.

Fractional order uncertainty estimator based hierarchical sliding mode design for a class of fractional order non-holonomic chained system.

PubMed

Deepika; Kaur, Sandeep; Narayan, Shiv

2018-06-01

This paper proposes a novel fractional order sliding mode control approach to address the issues of stabilization as well as tracking of an N-dimensional extended chained form of fractional order non-holonomic system. Firstly, the hierarchical fractional order terminal sliding manifolds are selected to procure the desired objectives in finite time. Then, a sliding mode control law is formulated which provides robustness against various system uncertainties or external disturbances. In addition, a novel fractional order uncertainty estimator is deduced mathematically to estimate and mitigate the effects of uncertainties, which also excludes the requirement of their upper bounds. Due to the omission of discontinuous control action, the proposed algorithm ensures a chatter-free control input. Moreover, the finite time stability of the closed loop system has been proved analytically through well known Mittag-Leffler and Fractional Lyapunov theorems. Finally, the proposed methodology is validated with MATLAB simulations on two examples including an application of fractional order non-holonomic wheeled mobile robot and its performances are also compared with the existing control approach. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

Pathological speech signal analysis and classification using empirical mode decomposition.

PubMed

Kaleem, Muhammad; Ghoraani, Behnaz; Guergachi, Aziz; Krishnan, Sridhar

2013-07-01

Automated classification of normal and pathological speech signals can provide an objective and accurate mechanism for pathological speech diagnosis, and is an active area of research. A large part of this research is based on analysis of acoustic measures extracted from sustained vowels. However, sustained vowels do not reflect real-world attributes of voice as effectively as continuous speech, which can take into account important attributes of speech such as rapid voice onset and termination, changes in voice frequency and amplitude, and sudden discontinuities in speech. This paper presents a methodology based on empirical mode decomposition (EMD) for classification of continuous normal and pathological speech signals obtained from a well-known database. EMD is used to decompose randomly chosen portions of speech signals into intrinsic mode functions, which are then analyzed to extract meaningful temporal and spectral features, including true instantaneous features which can capture discriminative information in signals hidden at local time-scales. A total of six features are extracted, and a linear classifier is used with the feature vector to classify continuous speech portions obtained from a database consisting of 51 normal and 161 pathological speakers. A classification accuracy of 95.7 % is obtained, thus demonstrating the effectiveness of the methodology.

Assessing the feasibility of the Effectiveness of Discontinuing Bisphosphonates trial: a pilot study.

PubMed

Wright, N C; Foster, P J; Mudano, A S; Melnick, J A; Lewiecki, M E; Shergy, W J; Curtis, J R; Cutter, G R; Danila, M I; Kilgore, M L; Lewis, E C; Morgan, S L; Redden, D T; Warriner, A H; Saag, K G

2017-08-01

The Effectiveness of Discontinuing Bisphosphonates (EDGE) study is a planned pragmatic clinical trial to guide "drug holiday" clinical decision making. This pilot study assessed work flow and feasibility of such a study. While participant recruitment and treatment adherence were suboptimal, administrative procedures were generally feasible and minimally disrupted clinic flow. The comparative effectiveness of continuing or discontinuing long-term alendronate (ALN) on fractures is unknown. A large pragmatic ALN discontinuation study has potential to answer this question. We conducted a 6-month pilot study of the planned the EDGE study among current long-term ALN users (women aged ≥65 with ≥3 years of ALN use) to determine study work flow and feasibility including evaluating the administrative aspects of trial conduct (e.g., time to contract, institutional review board (IRB) approval), assessing rates of site and participant recruitment, and evaluating post-randomization outcomes, including adherence, bisphosphonate-associated adverse events, and participant and site satisfaction. We assessed outcomes 1 and 6 months after randomization. Nine sites participated, including seven community-based medical practices and two academic medical centers. On average (SD), contract execution took 3.4 (2.3) months and IRB approval took 13.9 (4.1) days. Sites recruited 27 participants (13 to continue ALN and 14 to discontinue ALN). Over follow-up, 22% of participants did not adhere to their randomization assignment: 30.8% in the continuation arm and 14.3% in the discontinuation arm. No fractures or adverse events were reported. Sites reported no issues regarding work flow, and participants were highly satisfied with the study. Administrative procedures of the EDGE study were generally feasible, with minimal disruption to clinic flow. In this convenience sample, participant recruitment was suboptimal across most practice sites. Accounting for low treatment arm adherence, a comprehensive recruitment approach will be needed to effectively achieve the scientific goals of the EDGE study.

From current-driven to neoclassically driven tearing modes.

PubMed

Reimerdes, H; Sauter, O; Goodman, T; Pochelon, A

2002-03-11

In the TCV tokamak, the m/n = 2/1 island is observed in low-density discharges with central electron-cyclotron current drive. The evolution of its width has two distinct growth phases, one of which can be linked to a "conventional" tearing mode driven unstable by the current profile and the other to a neoclassical tearing mode driven by a perturbation of the bootstrap current. The TCV results provide the first clear observation of such a destabilization mechanism and reconcile the theory of conventional and neoclassical tearing modes, which differ only in the dominant driving term.

A possible mechanism of current termination in a reversed field pinch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagata, A.; Masamune, S.; Arimoto, H.

1989-10-01

A rapid growth of magnetic fluctuations resulting from the {ital m}=1 and {ital m}=2 modes and succeeding stop of rotation of these modes have been found as the precursor phenomena of current termination in the STP-3(M) (Trans. Inst. Elec. Eng. Jpn. {bold 107}-{bold B}, 469 (1987)) reversed field pinch. By deepening the field reversal at the wall, these precursors disappear and the current duration becomes much longer. It is found that sudden current termination is caused by a rapid growth of resistive tearing modes mainly because of nonlinear coupling of the {ital m}=1 mode.

MHD simulation of transition process from the magneto-rotational instability to magnetic turbulence by using a high-order MHD simulation scheme

NASA Astrophysics Data System (ADS)

Hirai, K.; Katoh, Y.; Terada, N.; Kawai, S.

2016-12-01

In accretion disks, magneto-rotational instability (MRI; Balbus & Hawley, 1991) makes the disk gas in the magnetic turbulent state and drives efficient mass accretion into a central star. MRI drives turbulence through the evolution of the parasitic instability (PI; Goodman & Xu, 1994), which is related to both Kelvin-Helmholtz (K-H) instability and magnetic reconnection. The wave number vector of PI is strongly affected by both magnetic diffusivity and fluid viscosity (Pessah, 2010). This fact makes MHD simulation of MRI difficult, because we need to employ the numerical diffusivity for treating discontinuities in compressible MHD simulation schemes. Therefore, it is necessary to use an MHD scheme that has both high-order accuracy so as to resolve MRI driven turbulence and small numerical diffusivity enough to treat discontinuities. We have originally developed an MHD code by employing the scheme proposed by Kawai (2013). This scheme focuses on resolving turbulence accurately by using a high-order compact difference scheme (Lele, 1992), and meanwhile, the scheme treats discontinuities by using the localized artificial diffusivity method (Kawai, 2013). Our code also employs the pipeline algorithm (Matsuura & Kato, 2007) for MPI parallelization without diminishing the accuracy of the compact difference scheme. We carry out a 3-dimensional ideal MHD simulation with a net vertical magnetic field in the local shearing box disk model. We use 256x256x128 grids. Simulation results show that the spatially averaged turbulent stress induced by MRI linearly grows until around 2.8 orbital periods, and decreases after the saturation. We confirm the strong enhancement of the K-H mode PI at a timing just before the saturation, identified by the enhancement of its anisotropic wavenumber spectra in the 2-dimensional wavenumber space. The wave number of the maximum growth of PI reproduced in the simulation result is larger than the linear analysis. This discrepancy is explained by the simulation result that a shear flow created by MRI locally becomes thinner and faster due to interactions between antiparallel vortices induced by K-H mode PI, and this structure induces small scale waves which break the shear flow itself. We report the results of the simulation, and discuss how the saturation amplitude of MRI is determined.

Seismic constraints on the radial dependence of the internal rotation profiles of six Kepler subgiants and young red giants

NASA Astrophysics Data System (ADS)

Deheuvels, S.; Doğan, G.; Goupil, M. J.; Appourchaux, T.; Benomar, O.; Bruntt, H.; Campante, T. L.; Casagrande, L.; Ceillier, T.; Davies, G. R.; De Cat, P.; Fu, J. N.; García, R. A.; Lobel, A.; Mosser, B.; Reese, D. R.; Regulo, C.; Schou, J.; Stahn, T.; Thygesen, A. O.; Yang, X. H.; Chaplin, W. J.; Christensen-Dalsgaard, J.; Eggenberger, P.; Gizon, L.; Mathis, S.; Molenda-Żakowicz, J.; Pinsonneault, M.

2014-04-01

Context. We still do not understand which physical mechanisms are responsible for the transport of angular momentum inside stars. The recent detection of mixed modes that contain the clear signature of rotation in the spectra of Kepler subgiants and red giants gives us the opportunity to make progress on this question. Aims: Our aim is to probe the radial dependence of the rotation profiles for a sample of Kepler targets. For this purpose, subgiants and early red giants are particularly interesting targets because their rotational splittings are more sensitive to the rotation outside the deeper core than is the case for their more evolved counterparts. Methods: We first extracted the rotational splittings and frequencies of the modes for six young Kepler red giants. We then performed a seismic modeling of these stars using the evolutionary codes Cesam2k and astec. By using the observed splittings and the rotational kernels of the optimal models, we inverted the internal rotation profiles of the six stars. Results: We obtain estimates of the core rotation rates for these stars, and upper limits to the rotation in their convective envelope. We show that the rotation contrast between the core and the envelope increases during the subgiant branch. Our results also suggest that the core of subgiants spins up with time, while their envelope spins down. For two of the stars, we show that a discontinuous rotation profile with a deep discontinuity reproduces the observed splittings significantly better than a smooth rotation profile. Interestingly, the depths that are found to be most probable for the discontinuities roughly coincide with the location of the H-burning shell, which separates the layers that contract from those that expand. Conclusions: We characterized the differential rotation pattern of six young giants with a range of metallicities, and with both radiative and convective cores on the main sequence. This will bring observational constraints to the scenarios of angular momentum transport in stars. Moreover, if the existence of sharp gradients in the rotation profiles of young red giants is confirmed, it is expected to help in distinguishing between the physical processes that could transport angular momentum in the subgiant and red giant branches. Appendices and Tables 3-9 are available in electronic form at http://www.aanda.org

Predicting Adherence and Persistence with Oral Bisphosphonate Therapy in an Integrated Health Care Delivery System.

PubMed

Hui, Rita L; Adams, Annette L; Niu, Fang; Ettinger, Bruce; Yi, David K; Chandra, Malini; Lo, Joan C

2017-04-01

Examining drug exposure is essential to pharmacovigilance, especially for bisphosphonate (BP) therapy. To examine differences in 4 measures of oral BP exposure: treatment discontinuation, adherence, persistence, and nonpersistence. Among women aged ≥ 50 years who initiated oral BP therapy during 2002-2007 with at least 3 years of health plan membership follow-up, discontinuation was defined by evidence of no further treatment during the study observation period. Among those with at least 2 filled BP prescriptions during the study period, adherence was calculated for each year of follow-up using the (modified) proportion of days covered (mPDC) metric that allows for stockpiling of prescription/refills overlap ≤ 30 days supply. Persistence was quantified by treatment duration, allowing a gap of up to 60 days between prescription/refill days covered. Nonpersistence was quantified by the periods without drugs outside this allowable gap. Multivariable logistic regression was used to compare age and race groups and the relationships of early adherence (adherence during the first year) with subsequent adherence. Among 48,390 women initiating oral BP therapy and followed for 3 years, 26.7% discontinued in year 1, and 14.7% of the remaining 35,456 women discontinued in year 2. Discontinuation rates were slightly higher (29.4%, P < 0.001) for women aged ≥ 75 years and somewhat lower (21.1%, P < 0.001) for Asian women. During the first year, 60.4% of the women achieved an mPDC of ≥ 75%, with demographic differences in adherence similar to that seen for treatment discontinuation. Over the 3 years, the median mPDC levels for BP therapy were 86%, 84%, and 85% in years 1, 2, and 3, respectively, for those receiving treatment. Cumulative persistence was 2.3 years (median, IQR = 1.0-3.0) overall and slightly greater for Asian versus white women and lower for older women. There were 18,174 (42.9%) women with at least 1 period of nonpersistence during 3 years follow-up in excess of the 60-day allowable gap between prescription/refills (median cumulative nonpersistence = 0.65, IQR = 0.30-1.25 years). Women with mPDC ≥ 75% during the first year had a 12-fold and 6-fold increased odds of mPDC ≥ 75% during year 2 and year 3, respectively. BP discontinuation rates are highest for women during the first year. Among those continuing treatment in subsequent years, adherence rates were relatively stable. Persistence and adherence varied slightly by age and was somewhat higher in Asians, contributing to differences in cumulative BP exposure. We also found evidence that optimal adherence in the first year was highly predictive of optimal adherence in the subsequent 1-2 years. Hence, subgroups of patients receiving oral BP drugs may require different levels of support and monitoring to maximize treatment benefit, especially based on early patterns of use. This study was supported by grants from the Kaiser Permanente Northern California Community Benefit Program and the National Institutes of Health, 1R01AG047230-01A1. The opinions expressed in this publication are solely the responsibility of the authors and do not represent the official views of Kaiser Permanente or the National Institutes of Health. Hui, Yi, and Chandra have received past research funding from Amgen not related to the current study. Adams has received research funding from Amgen, Merck, and Otsuka not related to the current study. Niu has received research funding from Bristol-Myers Squibb not related to the current study. Ettinger has received past legal fees in litigation involving Fosamax. Lo has received past research funding from Amgen and current research funding from Sanofi not related to the current study. The data from this study were presented at the Academy of Managed Care Pharmacy Annual Meeting; April 19-22, 2016; San Francisco, California. Study concept and design were contributed primarily by Hui and Lo, along with Adams, Niu, Yi, and Ettinger. Hui took the lead in data collection, along with Chandra, and data interpretation was performed by Niu, Yi, and Lo, along with the other authors. The manuscript was written by Hui, Adams, and Lo, along with Niu, Yi, and Ettinger, and revised by Ettinger, Hui, Lo, and Niu, along with the other authors.

3-D direct current resistivity anisotropic modelling by goal-oriented adaptive finite element methods

NASA Astrophysics Data System (ADS)

Ren, Zhengyong; Qiu, Lewen; Tang, Jingtian; Wu, Xiaoping; Xiao, Xiao; Zhou, Zilong

2018-01-01

Although accurate numerical solvers for 3-D direct current (DC) isotropic resistivity models are current available even for complicated models with topography, reliable numerical solvers for the anisotropic case are still an open question. This study aims to develop a novel and optimal numerical solver for accurately calculating the DC potentials for complicated models with arbitrary anisotropic conductivity structures in the Earth. First, a secondary potential boundary value problem is derived by considering the topography and the anisotropic conductivity. Then, two a posteriori error estimators with one using the gradient-recovery technique and one measuring the discontinuity of the normal component of current density are developed for the anisotropic cases. Combing the goal-oriented and non-goal-oriented mesh refinements and these two error estimators, four different solving strategies are developed for complicated DC anisotropic forward modelling problems. A synthetic anisotropic two-layer model with analytic solutions verified the accuracy of our algorithms. A half-space model with a buried anisotropic cube and a mountain-valley model are adopted to test the convergence rates of these four solving strategies. We found that the error estimator based on the discontinuity of current density shows better performance than the gradient-recovery based a posteriori error estimator for anisotropic models with conductivity contrasts. Both error estimators working together with goal-oriented concepts can offer optimal mesh density distributions and highly accurate solutions.

75 FR 12483 - Courtesy Notice of Liquidation

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-16

.... Currently, CBP provides an electronic and a paper courtesy notice for importers of record whose entry... notification process and reduce printing and mailing costs, CBP proposes to discontinue mailing paper courtesy... that relate to the economic, environmental, or federalism effects that might result from this proposed...

75 FR 75897 - Electronic Funds Transfer of Depository Taxes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-07

... the Financial Management Service to discontinue the system that processes FTD coupons, the temporary... Financial Management Service (FMS) considered current market conditions. In the last 18 months, more than 100 financial institutions, large and small, have stopped accepting FTD coupons. In many states, few...

77 FR 12764 - POSTNET Barcode Discontinuation

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-02

... routing code appears in the lower right corner. * * * * * [Delete current 5.6, DPBC Numeric Equivalent, in... correct ZIP Code, ZIP+4 code, or numeric equivalent to the delivery point routing code and which meets... equivalent to the delivery point routing code is formed by [[Page 12766

Developing Discontinuous Galerkin Methods for Solving Multiphysics Problems in General Relativity

NASA Astrophysics Data System (ADS)

Kidder, Lawrence; Field, Scott; Teukolsky, Saul; Foucart, Francois; SXS Collaboration

2016-03-01

Multi-messenger observations of the merger of black hole-neutron star and neutron star-neutron star binaries, and of supernova explosions will probe fundamental physics inaccessible to terrestrial experiments. Modeling these systems requires a relativistic treatment of hydrodynamics, including magnetic fields, as well as neutrino transport and nuclear reactions. The accuracy, efficiency, and robustness of current codes that treat all of these problems is not sufficient to keep up with the observational needs. We are building a new numerical code that uses the Discontinuous Galerkin method with a task-based parallelization strategy, a promising combination that will allow multiphysics applications to be treated both accurately and efficiently on petascale and exascale machines. The code will scale to more than 100,000 cores for efficient exploration of the parameter space of potential sources and allowed physics, and the high-fidelity predictions needed to realize the promise of multi-messenger astronomy. I will discuss the current status of the development of this new code.

Laboratory degradation studies of 14C-atrazine and -isoproturon in soil from sugarcane cultivated fields under Kenyan tropical conditions.

PubMed

Getenga, Z M; Dörfler, U; Schroll, R

2009-06-01

A study to compare the degradation rates of atrazine (6-chloro-N(2)-ethyl-N(4)-isopropyl-1,3,5-triazine-2,4-diammine) and isoproturon [3-(4-isopropylphenyl)-1,1-dimethylurea] in soils from sugarcane fields with different practices of herbicides application was carried out. (14)C-atrazine was poorly mineralized to (14)CO(2) (1.10% +/- 0.22%) after 139 days of incubation in soil without previous exposure to atrazine. In the same soil also with no previous isoproturon exposure isoproturon was mineralized to (14)CO(2) by 7.70% +/- 0.94%. Atrazine mineralization after 98 days was 13.4% +/- 0.30% in soil which discontinued the use of atrazine in 1997 while it was 89.9% +/- 1.23% in soil in which atrazine is currently being used. The isoproturon mineralization values were 7.24% +/- 0.85% and 22.97% +/- 0.96% in soil which discontinued atrazine and soil currently using atrazine, respectively.

A Current-Mode Common-Mode Feedback Circuit (CMFB) with Rail-to-Rail Operation

NASA Astrophysics Data System (ADS)

Suadet, Apirak; Kasemsuwan, Varakorn

2011-03-01

This paper presents a current-mode common-mode feedback (CMFB) circuit with rail-to-rail operation. The CMFB is a stand-alone circuit, which can be connected to any low voltage transconductor without changing or upsetting the existing circuit. The proposed CMFB employs current mirrors, operating as common-mode detector and current amplifier to enhance the loop gain of the CMFB. The circuit employs positive feedback to enhance the output impedance and gain. The circuit has been designed using a 0.18 μm CMOS technology under 1V supply and analyzed using HSPICE with BSIM3V3 device models. A pseudo-differential amplifier using two common sources and the proposed CMFB shows rail to rail output swing (± 0.7 V) with low common-mode gain (-36 dB) and power dissipation of 390 μW.

Mode control in a high-gain relativistic klystron amplifier

NASA Astrophysics Data System (ADS)

Li, Zheng-Hong; Zhang, Hong; Ju, Bing-Quan; Su, Chang; Wu, Yang

2010-05-01

Middle cavities between the input and output cavity can be used to decrease the required input RF power for the relativistic klystron amplifier. Meanwhile higher modes, which affect the working mode, are also easy to excite in a device with more middle cavities. In order for the positive feedback process for higher modes to be excited, a special measure is taken to increase the threshold current for such modes. Higher modes' excitation will be avoided when the threshold current is significantly larger than the beam current. So a high-gain S-band relativistic klystron amplifier is designed for the beam of current 5 kA and beam voltage 600 kV. Particle in cell simulations show that the gain is 1.6 × 105 with the input RF power of 6.8 kW, and that the output RF power reaches 1.1 GW.

Systematic expansion in the order parameter for replica theory of the dynamical glass transition.

PubMed

Jacquin, Hugo; Zamponi, Francesco

2013-03-28

It has been shown recently that predictions from mode-coupling theory for the glass transition of hard-spheres become increasingly bad when dimensionality increases, whereas replica theory predicts a correct scaling. Nevertheless if one focuses on the regime around the dynamical transition in three dimensions, mode-coupling results are far more convincing than replica theory predictions. It seems thus necessary to reconcile the two theoretic approaches in order to obtain a theory that interpolates between low-dimensional, mode-coupling results, and "mean-field" results from replica theory. Even though quantitative results for the dynamical transition issued from replica theory are not accurate in low dimensions, two different approximation schemes--small cage expansion and replicated hyper-netted-chain (RHNC)--provide the correct qualitative picture for the transition, namely, a discontinuous jump of a static order parameter from zero to a finite value. The purpose of this work is to develop a systematic expansion around the RHNC result in powers of the static order parameter, and to calculate the first correction in this expansion. Interestingly, this correction involves the static three-body correlations of the liquid. More importantly, we separately demonstrate that higher order terms in the expansion are quantitatively relevant at the transition, and that the usual mode-coupling kernel, involving two-body direct correlation functions of the liquid, cannot be recovered from static computations.

Optimized MPPT-based converter for TEG energy harvester to power wireless sensor and monitoring system in nuclear power plant

NASA Astrophysics Data System (ADS)

Xing, Shaoxu; Anakok, Isil; Zuo, Lei

2017-04-01

Accidents like Fukushima Disasters push people to improve the monitoring systems for the nuclear power plants. Thus, various types of energy harvesters are designed to power these systems and the Thermoelectric Generator (TEG) energy harvester is one of them. In order to enhance the amount of harvested power and the system efficiency, the power management stage needs to be carefully designed. In this paper, a power converter with optimized Maximum Power Point Tracking (MPPT) is proposed for the TEG Energy Harvester to power the wireless sensor network in nuclear power plant. The TEG Energy Harvester is installed on the coolant pipe of the nuclear plant and harvests energy from its heat energy while the power converter with optimized MPPT can make the TEG Energy Harvester output the maximum power, quickly response to the voltage change and provide sufficient energy for wireless sensor system to monitor the operation of the nuclear power plant. Due to the special characteristics of the Single-Ended Primary Inductor Converter (SEPIC) when it is working in the Discontinuous Inductor Current Mode (DICM) and Continuous Conduction Mode (CCM), the MPPT method presented in this paper would be able to control the converter to achieve the maximum output power in any working conditions of the TEG system with a simple circuit. The optimized MPPT algorithm will significantly reduce the cost and simplify the system as well as achieve a good performance. Experiment test results have shown that, comparing to a fixed- duty-cycle SEPIC which is specifically designed for the working on the secondary coolant loop in nuclear power plant, the optimized MPPT algorithm increased the output power by 55%.

80-GHz MMIC HEMT Voltage-Controlled Oscillator

NASA Technical Reports Server (NTRS)

Samoska, Lorene; Radisic, Vesna; Micovic, Miro; Hu, Ming; Janke, Paul; Ngo, Catherine; Nguyen, Loi

2003-01-01

A voltage-controlled oscillator (VCO) that operates in the frequency range from 77.5 to 83.5 GHz has been constructed in the form of a monolithic microwave integrated circuit (MMIC) that includes high-electron-mobility transistors (HEMTs). This circuit is a prototype of electronically tunable signal sources in the 75-to-110-GHz range, needed for communication, imaging, and automotive radar applications, among others. This oscillator (see Figure 1) includes two AlInAs/GaInAs/InP HEMTs. One HEMT serves mainly as an oscillator gain element. The other HEMT serves mainly as a varactor for controlling the frequency: the frequency-control element is its gate-to-source capacitance, which is varied by changing its gate supply voltage. The gain HEMT is biased for class-A operation (meaning that current is conducted throughout the oscillation cycle). Grounded coplanar waveguides are used as impedance-matching transmission lines, the input and output matching being chosen to sustain oscillation and maximize output power. Air bridges are placed at discontinuities to suppress undesired slot electromagnetic modes. A high density of vias is necessary for suppressing a parallel-plate electromagnetic mode that is undesired because it can propagate energy into the MMIC substrate. Previous attempts at constructing HEMT-based oscillators yielded circuits with relatively low levels of output power and narrow tuning ranges. For example, one HEMT VCO reported in the literature had an output power of 7 dBm (.5 mW) and a tuning range 2-GHz wide centered approximately at a nominal frequency of 77 GHz. In contrast, as shown in Figure 2, the present MMIC HEMT VCO puts out a power of 12.5 dBm (.18 mW) or more over the 6-GHz-wide frequency range from 77.5 to 83.5 GHz

Nonlinear MHD simulations of QH-mode DIII-D plasmas and implications for ITER high Q scenarios

NASA Astrophysics Data System (ADS)

Liu, F.; Huijsmans, G. T. A.; Loarte, A.; Garofalo, A. M.; Solomon, W. M.; Hoelzl, M.; Nkonga, B.; Pamela, S.; Becoulet, M.; Orain, F.; Van Vugt, D.

2018-01-01

In nonlinear MHD simulations of DIII-D QH-mode plasmas it has been found that low n kink/peeling modes (KPMs) are unstable and grow to a saturated kink-peeling mode. The features of the dominant saturated KPMs, which are localised toroidally by nonlinear coupling of harmonics, such as mode frequencies, density fluctuations and their effect on pedestal particle and energy transport, are in good agreement with the observations of the edge harmonic oscillation typically present in DIII-D QH-mode experiments. The nonlinear evolution of MHD modes including both kink-peeling modes and ballooning modes, is investigated through MHD simulations by varying the pedestal current and pressure relative to the initial conditions of DIII-D QH-mode plasma. The edge current and pressure at the pedestal are key parameters for the plasma either saturating to a QH-mode regime or a ballooning mode dominant regime. The influence of E × B flow and its shear on the QH-mode plasma has been investigated. E × B flow shear has a strong stabilisation effect on the medium to high-n modes but is destabilising for the n = 2 mode. The QH-mode extrapolation results of an ITER Q = 10 plasma show that the pedestal currents are large enough to destabilise n = 1-5 KPMs, leading to a stationary saturated kink-peeling mode.

Transverse Mode Dynamics of VCSELs Undergoing Current Modulation

NASA Technical Reports Server (NTRS)

Goorjian, Peter M.; Ning, C. Z.; Agrawal, Govind

2000-01-01

Transverse mode dynamics of a 20-micron-diameter vertical-cavity surface-emitting laser (VCSEL) undergoing gain switching by deep current modulation is studied numerically. The direct current (dc) level is set slightly below threshold and is modulated by a large alternating current (ac). The resulting optical pulse train and transverse-mode patterns are obtained numerically. The ac frequency is varied from 2.5 GHz to 10 GHz, and the ac amplitude is varied from one-half to four times that of the dc level. At high modulation frequencies, a regular pulse train is not generated unless the ac amplitude is large enough. At all modulation frequencies, the transverse spatial profile switches from single-mode to multiple-mode pattern as the ac pumping level is increased. Optical pulse widths vary in the range 5-30 ps. with the pulse width decreasing when either the frequency is increased or the ac amplitude is decreased. The numerical modeling uses an approximation form of the semiconductor Maxwell-Bloch equations. Temporal evolution of the spatial profiles of the laser (and of carrier density) is determined without any assumptions about the type or number of modes. Keywords: VCSELs, current modulation, gain switching, transverse mode dynamics, computational modeling

Current profile redistribution driven by neutral beam injection in a reversed-field pinch

NASA Astrophysics Data System (ADS)

Parke, E.; Anderson, J. K.; Brower, D. L.; Den Hartog, D. J.; Ding, W. X.; Johnson, C. A.; Lin, L.

2016-05-01

Neutral beam injection in reversed-field pinch (RFP) plasmas on the Madison Symmetric Torus [Dexter et al., Fusion Sci. Technol. 19, 131 (1991)] drives current redistribution with increased on-axis current density but negligible net current drive. Internal fluctuations correlated with tearing modes are observed on multiple diagnostics; the behavior of tearing mode correlated structures is consistent with flattening of the safety factor profile. The first application of a parametrized model for island flattening to temperature fluctuations in an RFP allows inferrence of rational surface locations for multiple tearing modes. The m = 1, n = 6 mode is observed to shift inward by 1.1 ± 0.6 cm with neutral beam injection. Tearing mode rational surface measurements provide a strong constraint for equilibrium reconstruction, with an estimated reduction of q0 by 5% and an increase in on-axis current density of 8% ± 5%. The inferred on-axis current drive is consistent with estimates of fast ion density using TRANSP [Goldston et al., J. Comput. Phys. 43, 61 (1981)].

Analysis of surface-water data network in Kansas for effectiveness in providing regional streamflow information; with a section on theory and application of generalized least squares

USGS Publications Warehouse

Medina, K.D.; Tasker, Gary D.

1987-01-01

This report documents the results of an analysis of the surface-water data network in Kansas for its effectiveness in providing regional streamflow information. The network was analyzed using generalized least squares regression. The correlation and time-sampling error of the streamflow characteristic are considered in the generalized least squares method. Unregulated medium-, low-, and high-flow characteristics were selected to be representative of the regional information that can be obtained from streamflow-gaging-station records for use in evaluating the effectiveness of continuing the present network stations, discontinuing some stations, and (or) adding new stations. The analysis used streamflow records for all currently operated stations that were not affected by regulation and for discontinued stations for which unregulated flow characteristics, as well as physical and climatic characteristics, were available. The State was divided into three network areas, western, northeastern, and southeastern Kansas, and analysis was made for the three streamflow characteristics in each area, using three planning horizons. The analysis showed that the maximum reduction of sampling mean-square error for each cost level could be obtained by adding new stations and discontinuing some current network stations. Large reductions in sampling mean-square error for low-flow information could be achieved in all three network areas, the reduction in western Kansas being the most dramatic. The addition of new stations would be most beneficial for mean-flow information in western Kansas. The reduction of sampling mean-square error for high-flow information would benefit most from the addition of new stations in western Kansas. Southeastern Kansas showed the smallest error reduction in high-flow information. A comparison among all three network areas indicated that funding resources could be most effectively used by discontinuing more stations in northeastern and southeastern Kansas and establishing more new stations in western Kansas.

An Iterative Method for Problems with Multiscale Conductivity

PubMed Central

Kim, Hyea Hyun; Minhas, Atul S.; Woo, Eung Je

2012-01-01

A model with its conductivity varying highly across a very thin layer will be considered. It is related to a stable phantom model, which is invented to generate a certain apparent conductivity inside a region surrounded by a thin cylinder with holes. The thin cylinder is an insulator and both inside and outside the thin cylinderare filled with the same saline. The injected current can enter only through the holes adopted to the thin cylinder. The model has a high contrast of conductivity discontinuity across the thin cylinder and the thickness of the layer and the size of holes are very small compared to the domain of the model problem. Numerical methods for such a model require a very fine mesh near the thin layer to resolve the conductivity discontinuity. In this work, an efficient numerical method for such a model problem is proposed by employing a uniform mesh, which need not resolve the conductivity discontinuity. The discrete problem is then solved by an iterative method, where the solution is improved by solving a simple discrete problem with a uniform conductivity. At each iteration, the right-hand side is updated by integrating the previous iterate over the thin cylinder. This process results in a certain smoothing effect on microscopic structures and our discrete model can provide a more practical tool for simulating the apparent conductivity. The convergence of the iterative method is analyzed regarding the contrast in the conductivity and the relative thickness of the layer. In numerical experiments, solutions of our method are compared to reference solutions obtained from COMSOL, where very fine meshes are used to resolve the conductivity discontinuity in the model. Errors of the voltage in L2 norm follow O(h) asymptotically and the current density matches quitewell those from the reference solution for a sufficiently small mesh size h. The experimental results present a promising feature of our approach for simulating the apparent conductivity related to changes in microscopic cellular structures. PMID:23304238

Retrospective review of treatment retention in pathological gambling.

PubMed

Grant, Jon E; Kim, Suck Won; Kuskowski, Michael

2004-01-01

Although research on pathological gambling is increasing, there are few studies examining correlates of treatment retention. In the current study, 50 outpatients with a primary DSM-IV diagnosis of pathological gambling treated in a clinical practice were assessed by chart review. Standard scales were used to rate subjects at baseline and at 2-month intervals. Subjects who dropped out of treatment were contacted by telephone to determine reasons for discontinuation of treatment. The mean duration of follow-up was 360.4 +/- 352.2 days. Twenty-four (48%) of the subjects discontinued treatment, including 14 (36.8%) of those subjects who were responders (defined as Clinical Global Impression [CGI] scale of "very much" or "much" improved) during at least one assessment point. Of those who discontinued treatment, 41.7% reported missing the thrill of gambling and 20.8% reported feeling certain that they could win and relieve financial burdens. Predictors of treatment continuation were responding to treatment within 8 weeks (odds ratio [OR], 6.00; 95% confidence interval [CI], 1.13 to 32.00; P =.04) and having a supportive environment (OR, 22.99; 95% CI, 5.04 to 104.76; P <.001). We conclude that a large percentage of patients with pathological gambling discontinue treatment. Predictors of treatment continuation may have clinical importance. Prospective longitudinal studies are needed to further elucidate the course of pathological gambling.

Laboratory investigations into fracture propagation characteristics of rock material

NASA Astrophysics Data System (ADS)

Prasad, B. N. V. Siva; Murthy, V. M. S. R.

2018-04-01

After Industrial Revolution, demand of materials for building up structures have increased enormously. Unfortunately, failures of such structures resulted in loss of life and property. Rock is anisotropic and discontinuous in nature with inherent flaws or so-called discontinuities in it. Rock is apparently used for construction in mining, civil, tunnelling, hydropower, geothermal and nuclear sectors [1]. Therefore, the strength of the structure built up considering rockmass as the construction material needs proper technical evaluation during designing stage itself to prevent and predict the scenarios of catastrophic failures due to these inherent fractures [2]. In this study, samples collected from nine different drilling sites have been investigated in laboratory for understanding the fracture propagation characteristics in rock. Rock material properties, ultrasonic velocities through pulse transmission technique and Mode I Fracture Toughness Testing of different variants of Dolomites and Graywackes are determined in laboratory and the resistance of the rock material to catastrophic crack extension or propagation has been determined. Based on the Fracture Toughness values and the rock properties, critical Energy Release Rates have been estimated. However further studies in this direction is to be carried out to understand the fracture propagation characteristics in three-dimensional space.

Avalanche outbreaks emerging in cooperative contagions

NASA Astrophysics Data System (ADS)

Cai, Weiran; Chen, Li; Ghanbarnejad, Fakhteh; Grassberger, Peter

2015-11-01

The spreading of contagions can exhibit a percolation transition, which separates transitory prevalence from outbreaks that reach a finite fraction of the population. Such transitions are commonly believed to be continuous, but empirical studies have shown more violent spreading modes when the participating agents are not limited to one type. Striking examples include the co-epidemic of the Spanish flu and pneumonia that occurred in 1918 (refs , ), and, more recently, the concurrent prevalence of HIV/AIDS and a host of diseases. It remains unclear to what extent an outbreak in the presence of interacting pathogens differs from that due to an ordinary single-agent process. Here we study a mechanistic model for understanding contagion processes involving inter-agent cooperation. Our stochastic simulations reveal the possible emergence of a massive avalanche-like outbreak right at the threshold, which is manifested as a discontinuous phase transition. Such an abrupt change arises only if the underlying network topology supports a bottleneck for cascaded mutual infections. Surprisingly, all these discontinuous transitions are accompanied by non-trivial critical behaviours, presenting a rare case of hybrid transition. The findings may imply the origin of catastrophic occurrences in many realistic systems, from co-epidemics to financial contagions.

Resting-State fMRI Functional Connectivity Is Associated with Sleepiness, Imagery, and Discontinuity of Mind

PubMed Central

Chen, Gang; den Braber, Anouk; van ‘t Ent, Dennis; Boomsma, Dorret I.; Mansvelder, Huibert D.; de Geus, Eco; Van Someren, Eus J. W.; Linkenkaer-Hansen, Klaus

2015-01-01

Resting-state functional magnetic resonance imaging (rs-fMRI) is widely used to investigate the functional architecture of the healthy human brain and how it is affected by learning, lifelong development, brain disorders or pharmacological intervention. Non-sensory experiences are prevalent during rest and must arise from ongoing brain activity, yet little is known about this relationship. Here, we used two runs of rs-fMRI both immediately followed by the Amsterdam Resting-State Questionnaire (ARSQ) to investigate the relationship between functional connectivity within ten large-scale functional brain networks and ten dimensions of thoughts and feelings experienced during the scan in 106 healthy participants. We identified 11 positive associations between brain-network functional connectivity and ARSQ dimensions. ‘Sleepiness’ exhibited significant associations with functional connectivity within Visual, Sensorimotor and Default Mode networks. Similar associations were observed for ‘Visual Thought’ and ‘Discontinuity of Mind’, which may relate to variation in imagery and thought control mediated by arousal fluctuations. Our findings show that self-reports of thoughts and feelings experienced during a rs-fMRI scan help understand the functional significance of variations in functional connectivity, which should be of special relevance to clinical studies. PMID:26540239

Variations in interior morphology of 15-20 km lunar craters - Implications for a major subsurface discontinuity

NASA Technical Reports Server (NTRS)

De Hon, R. A.

1980-01-01

Craters vary in morphology as a function of crater diameter, age, and mode of origin. This study concentrates on the morphology of young lunar impact craters within a limited size range. Elimination of morphologic variations generally attributed to crater size or age leaves a small population which should nearly reflect the varying properties of the lunar substrate. The sample consists of 17 craters 15-20 km in diameter with both simple and complex morphologies. While depth/diameter ratios do not obviously differ between mare and highland subsets, apparent depth, rim height, and profile data do differ distinctly. Highland craters tend to be deep, simple, and bowl-shaped. Mare craters tend to be shallow and flat-floored. Rim heights of complex mare craters are typically greater than those of simple craters. Differences of highland and mare crater morphologies are attributed to variations in the thickness of the lunar megaregolith. Highland craters in this size range do not penetrate the megaregolith. The depth and morphology of complex craters are controlled by the discontinuity at the transition from highly brecciated megaregolith to more coherent crystalline material of the upper crust.

Body-wave traveltime and amplitude shifts from asymptotic travelling wave coupling

USGS Publications Warehouse

Pollitz, F.

2006-01-01

We explore the sensitivity of finite-frequency body-wave traveltimes and amplitudes to perturbations in 3-D seismic velocity structure relative to a spherically symmetric model. Using the approach of coupled travelling wave theory, we consider the effect of a structural perturbation on an isolated portion of the seismogram. By convolving the spectrum of the differential seismogram with the spectrum of a narrow window taper, and using a Taylor's series expansion for wavenumber as a function of frequency on a mode dispersion branch, we derive semi-analytic expressions for the sensitivity kernels. Far-field effects of wave interactions with the free surface or internal discontinuities are implicitly included, as are wave conversions upon scattering. The kernels may be computed rapidly for the purpose of structural inversions. We give examples of traveltime sensitivity kernels for regional wave propagation at 1 Hz. For the direct SV wave in a simple crustal velocity model, they are generally complicated because of interfering waves generated by interactions with the free surface and the Mohorovic??ic?? discontinuity. A large part of the interference effects may be eliminated by restricting the travelling wave basis set to those waves within a certain range of horizontal phase velocity. ?? Journal compilation ?? 2006 RAS.

Lowering of the firing voltage and reducing of the discharge delay time in alternating current plasma display panels by a discontinuous spin-coated LaB{sub 6} film on the MgO protective layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deng, Jiang, E-mail: dj78291@163.com; Zeng, Baoqing; Zhongshan Institute, University of Electronic Science and Technology of China, 528402 zhongshan

2014-03-15

A spin coated LaB{sub 6} discontinuous film is covered on MgO protective layer to improve the discharge performance of alternating current plasma display panels. Under the premise of high transmittance of more than 90%, a very small amount of polycrystal LaB{sub 6} powders added in an organic solvent are chosen as the coating solution. The discharge characteristics results show that with 250 torr 5% Xe-Ne pressure, the firing voltage and discharge delay time of the test panel with LaB{sub 6}/MgO double protective layer are decreased by 13.4% and 36.5%, respectively, compared with that of conventional MgO protective layer, likely owingmore » to the low work function of LaB{sub 6.} Furthermore, the aging time of the proposed structure is comparable to that of pure MgO protective layer. Therefore, it will not increase the production costs and is highly suitable to be applied for alternating current plasma display panels with low electrical power consumption.« less

Synthesis of 1D Bragg gratings by a layer-aggregation method.

PubMed

Capmany, José; Muriel, Miguel A; Sales, Salvador

2007-08-15

We present what we believe to be a novel method for the synthesis of complex 1D (fiber and waveguide) Bragg gratings, which is based on an impedance reconstruction layer aggregation technique. The main advantage brought by the method is the possibility of synthesizing structures containing defects or discontinuities of the size of the local period, a feature that is not possible with prior reported methods. In addition, this enhanced spatial resolution allows the synthesis of very strong fiber Bragg grating devices providing convergent solutions. The method directly renders the refractive index profile n(z) as it does not rely on the coupled-mode theory.

Ultra-large distance modification of gravity from Lorentz symmetry breaking at the Planck scale

NASA Astrophysics Data System (ADS)

Gorbunov, Dmitry S.; Sibiryakov, Sergei M.

2005-09-01

We present an extension of the Randall-Sundrum model in which, due to spontaneous Lorentz symmetry breaking, graviton mixes with bulk vector fields and becomes quasilocalized. The masses of KK modes comprising the four-dimensional graviton are naturally exponentially small. This allows to push the Lorentz breaking scale to as high as a few tenth of the Planck mass. The model does not contain ghosts or tachyons and does not exhibit the van Dam-Veltman-Zakharov discontinuity. The gravitational attraction between static point masses becomes gradually weaker with increasing of separation and gets replaced by repulsion (antigravity) at exponentially large distances.

Computation of Engine Noise Propagation and Scattering Off an Aircraft

NASA Technical Reports Server (NTRS)

Xu, J.; Stanescu, D.; Hussaini, M. Y.; Farassat, F.

2003-01-01

The paper presents a comparison of experimental noise data measured in flight on a two-engine business jet aircraft with Kulite microphones placed on the suction surface of the wing with computational results. Both a time-domain discontinuous Galerkin spectral method and a frequency-domain spectral element method are used to simulate the radiation of the dominant spinning mode from the engine and its reflection and scattering by the fuselage and the wing. Both methods are implemented in computer codes that use the distributed memory model to make use of large parallel architectures. The results show that trends of the noise field are well predicted by both methods.

Continuous and Discontinuous Galerkin Methods for a Scalable Three-Dimensional Nonhydrostatic Atmospheric Model: Limited-Area Mode

DTIC Science & Technology

2012-03-09

guides/ ranger-user-guide. [3] T . Davies, M. J . P. Cullen, A. J . Malcolm, M. H. Mawson , A. Staniforth, A. A. White, and N. Wood. A new dynamical core...element Ωe, a finite-dimensional approximation qN is formed by expanding q(x, t ) in basis functions ψj (x) such that q (e) N (x, t ) = MN ∑ j =1 ψj(x)q (e... j ( t ) (14) where MN = (N + 1) 3 is the number of nodes per element, N is the order of the basis functions, and the superscript (e) denotes element

Angular and energy distribution of low energy cometary ions measured in the outer coma of Comet Halley

NASA Technical Reports Server (NTRS)

Berthelier, J. J.; Illiano, J. M.; Hodges, R. R.; Krankowsky, D.; Eberhardt, P.; Laemmerzahl, P.; Hoffman, J. H.; Herrwerth, I.; Woweries, J.; Dolder, U.

1986-01-01

During the early phase of the Giotto encounter with comet Halley, at distances from the nucleus greater than 350,000 km, the neutral mass spectrometer was operated in a mode allowing the measurement of low energy ions. Data reveal two important features of the outer coma: the presence of a sharp discontinuity in the plasma flow at 550,000 km from the nucleus which results in a significant decrease of the plasma flow accompanied by an increase in temperature; and the detection of newly born ions identified as O(+) and CO(+), at distances from the comet greater than 800,000 km.

Current collection from the space plasma through defects in solar array insulation

NASA Technical Reports Server (NTRS)

Robinson, R. S.; Stillwell, R. P.; Kaufman, H. R.

1985-01-01

Operating high-voltage solar arrays in the space environment can result in anomalously large currents being collected through small insulation defects. Tests simulating the electron collection have shown that there are two major collection modes. The first involves current enhancement by means of a surface phenomenon involving secondary electron emission from the surrounding insulator. In the second mode, the current collection is enhanced by vaporization and ionization of the insulator material, in addition to the surface enhancement of the first mode. The electron collection due to surface enhancement (first mode) has been modeled. Using this model, simple calculations yield realistic predictions.

75 FR 60341 - Deposit Insurance Regulations; Unlimited Coverage for Noninterest-bearing Transaction Accounts

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-30

... mail for depositors who ordinarily receive account information in this manner. The notice may be in the... existing information collection, OMB No. 3064-0168, currently entitled SWEEP Accounts: Disclosure of... discontinue its existing ``Transaction Account Guarantee Program Extension'' information collection, OMB No...

Localized Artificial Viscosity Stabilization of Discontinuous Galerkin Methods for Nonhydrostatic Mesoscale Atmospheric Modeling

DTIC Science & Technology

2014-01-01

with a Riemann flux !"#! (!! ,!!!,), where !!! denotes the solution outside the current element !. Various (approximate) Riemann solvers ...can be used to calculate the Riemann flux, and the Rusanov Riemann solver is adopted in this paper. Then Eq. (7) can be rewritten as !

Differential Velocity between Solar Wind Protons and Alpha Particles in Pressure Balance Structures

NASA Technical Reports Server (NTRS)

Yamauchi, Yohei; Suess, Steven T.; Steinberg, John T.; Sakurai, Takashi

2004-01-01

Pressure balance structures (PBSs) are a common high-plasma beta feature in high-latitude, high-speed solar wind. They have been proposed as remnants of coronal plumes. If true, they should reflect the observation that plumes are rooted in unipolar magnetic flux concentrations in the photosphere and are heated as oppositely directed flux is advected into and reconnects with the flux concentration. A minimum variance analysis (MVA) of magnetic discontinuities in PBSs showed there is a larger proportion of tangential discontinuities than in the surrounding high-speed wind, supporting the hypothesis that plasmoids or extended current sheets are formed during reconnection at the base of plumes. To further evaluate the character of magnetic field discontinuities in PBSs, differential streaming between alpha particles and protons is analyzed here for the same sample of PBSs used in the MVA. Alpha particles in high-speed wind generally have a higher radial flow speed than protons. However, if the magnetic field is folded back on itself, as in a large-amplitude Alfven wave, alpha particles will locally have a radial flow speed less than protons. This characteristic is used here to distinguish between folded back magnetic fields (which would contain rotational discontinuities) and tangential discontinuities using Ulysses high-latitude, high-speed solar wind data. The analysis indicates that almost all reversals in the radial magnetic field in PBSs are folded back field lines. This is found to also be true outside PBSs, supporting existing results for typical high-speed, high-latitude wind. There remains a small number of cases that appear not to be folds in the magnetic field and which may be flux tubes with both ends rooted in the Sun. The distinct difference in MVA results inside and outside PBSs remains unexplained.

Differential Velocity Between Solar Wind Protons and Alpha Particles in Pressure Balance Structures

NASA Technical Reports Server (NTRS)

Yamauchi, Y.; Suess, S. T.; Steinberg, J. T.; Sakurai, T.

2003-01-01

Pressure balance structures (PBSs) are a common high plasma beta feature in high latitude, high speed solar wind. They have been proposed as remnants of coronal plumes. If true, they should reflect the observation that plumes are rooted in unipolar magnetic flux concentrations in the photosphere and are heated as oppositely directed flux is advected into and reconnects with the flux concentration. A minimum variance analysis (MVA) of magnetic discontinuities in PBSs showed there is a larger proportion of tangential discontinuities than in the surrounding high speed wind, supporting the hypothesis that plasmoids or extended current sheets are formed during reconnection at the base of plumes. To further evaluate the character of magnetic field discontinuities in PBSs, differential streaming between alpha particles and protons is analyzed here for the same sample of PBSs used in the MVA. Alpha particles in high speed wind generally have a higher radial flow speed than protons. However, if the magnetic field is folded back on itself, as in a large amplitude Alfven wave, alpha particles will locally have a radial flow speed less than protons. This characteristic is used here to distinguish between folded back magnetic fields (which would contain rotational discontinuities) and tangential discontinuities using Ulysses high latitude, high speed solar wind data. The analysis indicates that almost all reversals in the radial magnetic field in PBSs are folded back field lines. This is found to also be true outside PBSs, supporting existing results for typical high speed, high latitude wind. There remains a small number of cases that appear not to be folds in the magnetic field and which may be flux tubes with both ends rooted in the Sun. The distinct difference in MVA results inside and outside PBSs remains unexplained.

Long-term satisfaction and predictors of use in patients using intracorporeal injections (ICI) for post-prostatectomy erectile dysfunction (PPED)

PubMed Central

Prabhu, Vinay; Alukal, Joseph; Laze, Juliana; Makarov, Danil V.; Lepor, Herbert

2013-01-01

Purpose ICI has low utilization and high discontinuation rates. We examined factors associated with ICI use, long-term satisfaction with ICI, and reasons for discontinuation in men having undergone radical prostatectomy. Materials and Methods Between October 2000 and September 2003, 731 men undergoing open radical retropubic prostatectomy were enrolled in a prospective outcomes study. The eight-year follow-up evaluation included the UCLA-PCI and a survey capturing ICI use, satisfaction, and reasons for discontinuation. Logistic regression was utilized to determine associations between ICI use and pre-operative variables. Results Eight-year self-assessment was completed by 368 (50.4%) men; 140 (38%) of these indicated prior or current ICI use, with only 34 using ICI at eight years. Forty four percent of men were satisfied with ICI. Discontinuation reasons included: dislike (47%), pain (33%), return of erection (19%), inefficacy (14%), and no partner (6%). Men trying ICI had greater pre-operative UCLA-PCI sexual function scores (75.2 vs. 65.62, p = 0.00005) and greater declines in this score at three months (p = 0.0002) and two years (p = 0.003). Higher pre-operative sexual function scores were independently associated with utilization of ICI in a model adjusted for age, marital status, nerve sparing status, and BMI (OR =1.021, 95% CI 1.008–1.035). Conclusions Men pursuing ICI have better baseline erectile function and experience greater deterioration in erectile function during the early post-operative period. Despite high efficacy, many discontinue ICI due to dislike or discomfort. Satisfaction rates with ICI indicate its long-term role in restoring sexual function in men with PPED. PMID:23174252

Prognostic health monitoring in switch-mode power supplies with voltage regulation

NASA Technical Reports Server (NTRS)

Hofmeister, James P (Inventor); Judkins, Justin B (Inventor)

2009-01-01

The system includes a current injection device in electrical communication with the switch mode power supply. The current injection device is positioned to alter the initial, non-zero load current when activated. A prognostic control is in communication with the current injection device, controlling activation of the current injection device. A frequency detector is positioned to receive an output signal from the switch mode power supply and is able to count cycles in a sinusoidal wave within the output signal. An output device is in communication with the frequency detector. The output device outputs a result of the counted cycles, which are indicative of damage to an a remaining useful life of the switch mode power supply.

The mode 3 crack problem in bonded materials with a nonhomogeneous interfacial zone

NASA Technical Reports Server (NTRS)

Erdogan, Fazil; Kaya, A. C.; Joseph, P. F.

1988-01-01

The mode 3 crack problem for two bonded homogeneous half planes was considered. The interfacial zone was modelled by a nonhomogeneous strip in such a way that the shear modulus is a continuous function throughout the composite medium and has discontinuous derivatives along the boundaries of the interfacial zone. The problem was formulated for cracks perpendicular to the nominal interface and was solved for various crack locations in and around the interfacial region. The asymptotic stress field near the tip of a crack terminating at an interface was examined and it was shown that, unlike the corresponding stress field in piecewise homogeneous materials, in this case the stresses have the standard square root singularity and their angular variation was identical to that of a crack in a homogeneous medium. With application to the subcritical crack growth process in mind, the results given include mostly the stress intensity factors for some typical crack geometries and various material combinations.

The mode III crack problem in bonded materials with a nonhomogeneous interfacial zone

NASA Technical Reports Server (NTRS)

Erdogan, F.; Joseph, P. F.; Kaya, A. C.

1991-01-01

The mode 3 crack problem for two bonded homogeneous half planes was considered. The interfacial zone was modelled by a nonhomogeneous strip in such a way that the shear modulus is a continuous function throughout the composite medium and has discontinuous derivatives along the boundaries of the interfacial zone. The problem was formulated for cracks perpendicular to the nominal interface and was solved for various crack locations in and around the interfacial region. The asymptotic stress field near the tip of a crack terminating at an interface was examined and it was shown that, unlike the corresponding stress field in piecewise homogeneous materials, in this case the stresses have the standard square root singularity and their angular variation was identical to that of a crack in a homogeneous medium. With application to the subcritical crack growth process in mind, the results given include mostly the stress intensity factors for some typical crack geometries and various material combinations.

Predicting Properties of Unidirectional-Nanofiber Composites

NASA Technical Reports Server (NTRS)

Chamis, Christos C.; Handler, Louis M.; Manderscheid, Jane

2008-01-01

A theory for predicting mechanical, thermal, electrical, and other properties of unidirectional-nanofiber/matrix composite materials is based on the prior theory of micromechanics of composite materials. In the development of the present theory, the prior theory of micromechanics was extended, through progressive substructuring, to the level of detail of a nanoscale slice of a nanofiber. All the governing equations were then formulated at this level. The substructuring and the equations have been programmed in the ICAN/JAVA computer code, which was reported in "ICAN/JAVA: Integrated Composite Analyzer Recoded in Java" (LEW-17247), NASA Tech Briefs, Vol. 26, No. 12 (December 2002), page 36. In a demonstration, the theory as embodied in the computer code was applied to a graphite-nanofiber/epoxy laminate and used to predict 25 properties. Most of the properties were found to be distributed along the through-the-thickness direction. Matrix-dependent properties were found to have bimodal through-the-thickness distributions with discontinuous changes from mode to mode.

Elastic Model Transitions Using Quadratic Inequality Constrained Least Squares

NASA Technical Reports Server (NTRS)

Orr, Jeb S.

2012-01-01

A technique is presented for initializing multiple discrete finite element model (FEM) mode sets for certain types of flight dynamics formulations that rely on superposition of orthogonal modes for modeling the elastic response. Such approaches are commonly used for modeling launch vehicle dynamics, and challenges arise due to the rapidly time-varying nature of the rigid-body and elastic characteristics. By way of an energy argument, a quadratic inequality constrained least squares (LSQI) algorithm is employed to e ect a smooth transition from one set of FEM eigenvectors to another with no requirement that the models be of similar dimension or that the eigenvectors be correlated in any particular way. The physically unrealistic and controversial method of eigenvector interpolation is completely avoided, and the discrete solution approximates that of the continuously varying system. The real-time computational burden is shown to be negligible due to convenient features of the solution method. Simulation results are presented, and applications to staging and other discontinuous mass changes are discussed

Collective Dynamics of Periplasmic Glutamine Binding Protein upon Domain Closure

PubMed Central

Loeffler, Hannes H.; Kitao, Akio

2009-01-01

The glutamine binding protein is a vital component of the associated ATP binding cassette transport systems responsible for the uptake of glutamine into the cell. We have investigated the global movements of this protein by molecular dynamics simulations and principal component analysis (PCA). We confirm that the most dominant mode corresponds to the biological function of the protein, i.e., a hinge-type motion upon ligand binding. The closure itself was directly observed from two independent trajectories whereby PCA was used to elucidate the nature of this closing reaction. Two intermediary states are identified and described in detail. The ligand binding induces the structural change of the hinge regions from a discontinuous β-sheet to a continuous one, which also enhances softness of the hinge and modifies the direction of hinge motion to enable closing. We also investigated the convergence behavior of PCA modes, which were found to converge rather quickly when the associated magnitudes of the eigenvalues are well separated. PMID:19883597

Sneaker Male Squid Produce Long-lived Spermatozoa by Modulating Their Energy Metabolism *

PubMed Central

Hirohashi, Noritaka; Tamura-Nakano, Miwa; Nakaya, Fumio; Iida, Tomohiro; Iwata, Yoko

2016-01-01

Spermatozoa released by males should remain viable until fertilization. Hence, sperm longevity is governed by intrinsic and environmental factors in accordance with the male mating strategy. However, whether intraspecific variation of insemination modes can impact sperm longevity remains to be elucidated. In the squid Heterololigo bleekeri, male dimorphism (consort and sneaker) is linked to two discontinuous insemination modes that differ in place and time. Notably, only sneaker male spermatozoa inseminated long before egg spawning can be stored in the seminal receptacle. We found that sneaker spermatozoa exhibited greater persistence in fertilization competence and flagellar motility than consort ones because of a larger amount of flagellar glycogen. Sneaker spermatozoa also showed higher capacities in glucose uptake and lactate efflux. Lactic acidosis was considered to stabilize CO2-triggered self-clustering of sneaker spermatozoa, thus establishing hypoxia-induced metabolic changes and sperm survival. These results, together with comparative omics analyses, suggest that postcopulatory reproductive contexts define sperm longevity by modulating the inherent energy levels and metabolic pathways. PMID:27385589

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ranjan, Devesh

Diffusion bonded heat exchangers are the leading candidates for the sCO 2 Brayton cycles in next generation nuclear power plants. Commercially available diffusion bonded heat exchangers utilize set of continuous semi-circular zigzag micro channels to increase the heat transfer area and enhance heat transfer through increased turbulence production. Such heat exchangers can lead to excessive pressure drop as well as flow maldistribution in the case of poorly designed flow distribution headers. The goal of the current project is to fabricate and test potential discontinuous fin patterns for diffusion bonded heat exchangers; which can achieve desired thermal performance at lower pressuremore » drops. Prototypic discontinuous offset rectangular and Airfoil fin surface geometries were chemically etched on to 316 stainless steel plate and sealed against an un-etched flat pate using O-ring seal emulating diffusion bonded heat exchangers. Thermal-hydraulic performance of these prototypic discontinuous fin geometries was experimentally evaluated and compared to the existing data for the continuous zigzag channels. The data generated from this project will serve as the database for future testing and validation of numerical models.« less

Discharge mode transition and temporal-spatial evolution of an air-water plasma jet generated by pulsating DC power

NASA Astrophysics Data System (ADS)

Lei, J.; Geng, Y.; Liu, K.; Zhu, W.; Zheng, Z.; Hu, H.

2017-12-01

In this paper, pulsating direct current air-water plasma jet, which can increase the production of •OH and decrease the temperature, is studied. The results show that the discharge mode changes in one cycle from corona discharge with steep Trichel current pulse to glow-like discharge. It is unknown whether the different discharge modes and water ratio have an effect on the transient process of the excited O and •OH production and the mechanism of plasma propagation. So, a series of experiments are done in this paper. The results show that the changing rules of both the excited state O and the discharge current reach their two peak values synchronously. And its maximum appears at the time of the first peak current value in corona mode. However, the change of the excited state •OH is different. It increases to its maximum at the time of the second peak current value in glow-like mode. Besides, the intensified charge coupled device photographs show that the luminous intensity of the discharge zone at the first peak current value in corona mode is stronger than the second peak current value in glow-like mode. At the same time, the discharge area of the former is larger than the latter. Nevertheless, with the increase in water ratio, the discharge area change reversed. Additionally, the air plasma plume propagation depends on the gas flow. The initial propagation velocity decreases with the increase in water ratio.

DSS range delay calibrations: Current performance level

NASA Technical Reports Server (NTRS)

Spradlin, G. L.

1976-01-01

A means for evaluating Deep Space Station (DSS) range delay calibration performance was developed. Inconsistencies frequently noted in these data are resolved. Development of the DSS range delay data base is described. The data base is presented with comments regarding apparent discontinuities. Data regarding the exciter frequency dependence of the delay values are presented. The improvement observed in the consistency of current DSS range delay calibration data over the performance previously observed is noted.

Quality evaluation and control of end cap welds in PHWR fuel elements by ultrasonic examination

NASA Astrophysics Data System (ADS)

Choi, M. S.; Yang, M. S.

1991-02-01

The current quality control procedure of nuclear fuel end cap weld is mainly dependent on the destructive metallographic examination. A nondestructive examination technique, i.e., ultrasonic examination, has been developed to identify and evaluate weld discontinuities. A few interesting results of the weld quality evaluation by applying the developed ultrasonic examination technique to PHWR fuel welds are presented. In addition, the feasibility of the weld quality control by the ultrasonic examination is discussed. This study shows that the ultrasonic examination is effective and reliable method for detecting abnormal weld contours and weld discontinuities such as micro-fissure, crack, upset split and expulsion, and can be used as a quality control tool for the end cap welding process.

Asynchronous communication in spectral-element and discontinuous Galerkin methods for atmospheric dynamics - a case study using the High-Order Methods Modeling Environment (HOMME-homme_dg_branch)

NASA Astrophysics Data System (ADS)

Jamroz, Benjamin F.; Klöfkorn, Robert

2016-08-01

The scalability of computational applications on current and next-generation supercomputers is increasingly limited by the cost of inter-process communication. We implement non-blocking asynchronous communication in the High-Order Methods Modeling Environment for the time integration of the hydrostatic fluid equations using both the spectral-element and discontinuous Galerkin methods. This allows the overlap of computation with communication, effectively hiding some of the costs of communication. A novel detail about our approach is that it provides some data movement to be performed during the asynchronous communication even in the absence of other computations. This method produces significant performance and scalability gains in large-scale simulations.

General practitioners' decisions about discontinuation of medication: an explorative study.

PubMed

Nixon, Michael Simon; Vendelø, Morten Thanning

2016-06-20

Purpose - The purpose of this paper is to investigate how general practitioners' (GPs) decisions about discontinuation of medication are influenced by their institutional context. Design/methodology/approach - In total, 24 GPs were interviewed, three practices were observed and documents were collected. The Gioia methodology was used to analyse data, drawing on a theoretical framework that integrate the sensemaking perspective and institutional theory. Findings - Most GPs, who actively consider discontinuation, are reluctant to discontinue medication, because the safest course of action for GPs is to continue prescriptions, rather than discontinue them. The authors conclude that this is in part due to the ambiguity about the appropriateness of discontinuing medication, experienced by the GPs, and in part because the clinical guidelines do not encourage discontinuation of medication, as they offer GPs a weak frame for discontinuation. Three reasons for this are identified: the guidelines provide dominating triggers for prescribing, they provide weak priming for discontinuation as an option, and they underscore a cognitive constraint against discontinuation. Originality/value - The analysis offers new insights about decision making when discontinuing medication. It also offers one of the first examinations of how the institutional context embedding GPs influences their decisions about discontinuation. For policymakers interested in the discontinuation of medication, the findings suggest that de-stigmatising discontinuation on an institutional level may be beneficial, allowing GPs to better justify discontinuation in light of the ambiguity they experience.

75 FR 47284 - Secretary's Priorities for Discretionary Grant Programs

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-05

... the most currently available data. Interrupted time series design \\4\\ means a type of quasi... findings. \\4\\ A single subject or single case design is an adaptation of an interrupted time series design...), interrupted time series designs (as defined in this notice), or regression discontinuity designs (as defined...

75 FR 16360 - Dan Kane; Receipt of Petition for Rulemaking

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-01

... certainties in light of the current administration's proposed defunding of the Yucca Mountain Repository for... construction of a mined geologic repository for spent nuclear fuel (Yucca Mountain) from the U.S. Department of... Mountain repository be discontinued for what the petitioner believes are political reasons. The petitioner...

Educational Leadership at 2050: Conjectures, Challenges, and Promises

ERIC Educational Resources Information Center

Papa, Rosemary; Mullen, Carol A.; English, Fenwick W.; Creighton, Theodore

2012-01-01

This is a practical, bold, no-holds barred look at challenges facing educational leaders and the university programs that prepare them through mid-century. It examines key continuities and discontinuities of current times for school, education, and society. Both practice and preparation occur in contested social space, the implications of which…

Nonlinear saturation amplitudes in classical Rayleigh-Taylor instability at arbitrary Atwood numbers

NASA Astrophysics Data System (ADS)

Liu, W. H.; Wang, L. F.; Ye, W. H.; He, X. T.

2012-04-01

In this research, nonlinear saturation amplitudes (NSAs) of the first two harmonics in Rayleigh-Taylor instability (RTI) for irrotational, incompressible, and inviscid fluids, with a discontinuous profile at arbitrary Atwood numbers, are investigated analytically, by considering nonlinear corrections up to the tenth-order. The NSA of the fundamental mode is defined as the linear (purely exponential) growth amplitude of the fundamental mode at the saturation time when the growth of the fundamental mode (first harmonic) is reduced by 10% in comparison to its corresponding linear growth. The NSA of the second harmonic can be obtained in the same way. The analytic results indicate that the effects of the higher-order correction (HOC) and the Atwood number (A) play an important role in the NSA of the RTI. It is found that the NSA of the fundamental mode decreases with increasing A. And when the HOC effects are considered, the NSA of the fundamental mode is significantly larger than the prediction of previous literatures within the framework of third-order perturbation theory [J. W. Jacobs and I. Catton, J. Fluid Mech. 187, 329 (1988); S. W. Haan, Phys. Fluids B 3, 2349 (1991)]. We find that the NSA of the second harmonic first decreases quickly with increasing A, reaching a minimum, and then increases slowly. Furthermore, the NSAs of the first two harmonics demonstrate the trend of convergence as the order of corrections increases. Thus, it should be included in applications where the NSAs play a role, such as inertial confinement fusion ignition target design.

A current-driven resistive instability and its nonlinear effects in simulations of coaxial helicity injection in a tokamak

DOE PAGES

Hooper, E. B.; Sovinec, C. R.

2016-10-06

An instability observed in whole-device, resistive magnetohydrodynamic simulations of the driven phase of coaxial helicity injection in the National Spherical Torus eXperiment is identified as a current-driven resistive mode in an unusual geometry that transiently generates a current sheet. The mode consists of plasma flow velocity and magnetic field eddies in a tube aligned with the magnetic field at the surface of the injected magnetic flux. At low plasma temperatures (~10–20 eV), the mode is benign, but at high temperatures (~100 eV) its amplitude undergoes relaxation oscillations, broadening the layer of injected current and flow at the surface of themore » injected toroidal flux and background plasma. The poloidal-field structure is affected and the magnetic surface closure is generally prevented while the mode undergoes relaxation oscillations during injection. Furthermore, this study describes the mode and uses linearized numerical computations and an analytic slab model to identify the unstable mode.« less

Investigation on Microstructure and Mechanical Properties of Continuous and Pulsed Current Gas Tungsten Arc Welded alloy 600

NASA Astrophysics Data System (ADS)

Srikanth, A.; Manikandan, M.

2018-02-01

The present study investigates the microstructure and mechanical properties of joints fabricated by Continuous and pulsed current gas tungsten arc welded alloy 600. Welding was done by autogenous mode. The macro examination was carried out to evaluate the welding defects in the weld joints. Optical and Scanning Electron Microscope (SEM) were performed to assess the microstructural changes in the fusion zone. Energy Dispersive Spectroscopy (EDS) analysis was carried to evaluate the microsegregation of alloying elements in the fusion zone. The tensile test was conducted to assess the strength of the weld joints. The results show that no welding defects were observed in the fusion zones of Continuous and Pulsed current Gas Tungsten Arc Welding. The refined microstructure was found in the pulsed current compared to continuous current mode. Microsegregation was not noticed in the weld grain boundary of continuous and pulsed current mode. The pulsed current shows improved mechanical properties compared to the continuous current mode.

Satellite Altimetry and Current-Meter Velocities in the Malvinas Current at 41°S: Comparisons and Modes of Variations

NASA Astrophysics Data System (ADS)

Ferrari, Ramiro; Artana, Camila; Saraceno, Martin; Piola, Alberto R.; Provost, Christine

2017-12-01

Three year long current-meter arrays were deployed in the Malvinas Current at 41°S below a satellite altimeter track at about 10 years intervals. Surface geostrophic velocities (SGV) derived from satellite altimetric data are compared with the in situ velocities at the upper current meter (˜300 m). Multisatellite gridded SGV compare better with in situ observations than along-track SGV. In spite of the proximity of the moorings to the complex Brazil-Malvinas Confluence (BMC) region, satellite SGV are significantly correlated with the 20 day low-passed in situ velocities (0.85 for along-isobaths velocities, 0.8 for cross-isobaths velocities). The recent in situ measurement period (2014-2015) stands out in the altimetry record with a long-lasting (4 months) high level of eddy kinetic energy at the mooring site and a southernmost location of the Subantarctic Front (SAF). The first two modes of variations of sea level anomaly (SLA) over the BMC remarkably match the first two modes of the low-passed in situ velocities. The first mode is associated with a latitudinal migration of the SAF, and the second with a longitudinal displacement of the Brazil Current overshoot. The two modes dominate the 24 year long record of SLA in the BMC, with energy peaks at the annual and semiannual periods for the first mode and at 3-5 months for the second mode. The SLA over the Southwest Atlantic was regressed onto the two confluence modes of SLA variations and showed remarkable standing wave train like structures in the Argentine Basin.

Roughness of the Mantle Transition Zone Discontinuities Revealed by High Resolution Wavefield Imaging with the Earthscope Transportable Array

NASA Astrophysics Data System (ADS)

Wang, Y.; Pavlis, G. L.

2015-12-01

We post-processed 141,080 pairs of high quality radial and transverse receiver functions from the Earthscope Automated Receiver Survey using a variant of what we have called generalized iterative deconvolution method and reshaped the spiking output into different scales of Ricker wavelets. We then used these data as input to our 3D plane wave migration method to produce an image volume of P to S scattering surfaces under all of the lower 48 states. The result is arguably the highest resolution image ever produce of the mantle transition zone. Due to the effect of migration impulse response, different scales of Ricker wavelets provide another important means of controlling the resolution of the image produced by 3D plane wave migration method. Model simulation shows that comparing to the widely used CCP stacking method with receiver functions shaped by Gaussian wavelet, the application of our methods is capable of resolving not only dipping discontinuities but also more subtle details of the discontinuities. Application to the latest USArray data reveals several previously unobserved features of the 410 and 660 discontinuities. Both discontinuities are resolved to a precision approaching 1 km under the stable interior, but degrading to the order of 10 km in the western US due to a probably combination of higher attenuation and velocity heterogeneity not resolved by current generation tomography models. Topography with many 10s of km is resolved at a range of scales. In addition, we observe large variation of relative amplitude on the radial component and large variations in the radial to transverse amplitude ratio that correlate with inferred variations in discontinuity topography. We argue this combination of observations can be explained by roughness at a range of scales. Roughness is consistent with the phase-change model for these discontinuities given there is little reason to think the mantle is homogeneous at these distance scales. Continental scale isopach of the transition zones shows the average thickness of the transition is approximately 15 km greater in the eastern US compared to the western US. This change occurs on a well define boundary roughly under the Mississippi River. The standard phase change model would thus predict higher transition zone temperatures on the western side of this boundary.

Current profile redistribution driven by neutral beam injection in a reversed-field pinch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parke, E.; Department of Physics, University of Wisconsin-Madison 1150 University Ave., Madison, Wisconsin 53706; Anderson, J. K.

2016-05-15

Neutral beam injection in reversed-field pinch (RFP) plasmas on the Madison Symmetric Torus [Dexter et al., Fusion Sci. Technol. 19, 131 (1991)] drives current redistribution with increased on-axis current density but negligible net current drive. Internal fluctuations correlated with tearing modes are observed on multiple diagnostics; the behavior of tearing mode correlated structures is consistent with flattening of the safety factor profile. The first application of a parametrized model for island flattening to temperature fluctuations in an RFP allows inferrence of rational surface locations for multiple tearing modes. The m = 1, n = 6 mode is observed to shift inward by 1.1 ± 0.6 cm withmore » neutral beam injection. Tearing mode rational surface measurements provide a strong constraint for equilibrium reconstruction, with an estimated reduction of q{sub 0} by 5% and an increase in on-axis current density of 8% ± 5%. The inferred on-axis current drive is consistent with estimates of fast ion density using TRANSP [Goldston et al., J. Comput. Phys. 43, 61 (1981)].« less

A Low Cost Single Chip VDL Compatible Transceiver ASIC

NASA Technical Reports Server (NTRS)

Becker, Robert

2004-01-01

Recent trends in commercial communications system components have focussed almost exclusively on cellular telephone technology. As many of the traditional sources of receiver components have discontinued non-cellular telephone products, the designers of avionics and other low volume radio applications find themselves increasingly unable to find highly integrated components. This is particularly true for low power, low cost applications which cannot afford the lavish current consumption of the software defined radio approach increasingly taken by certified device manufacturers. In this paper, we describe a low power transceiver chip targeting applications from low VHF to low UHF frequencies typical of avionics systems. The chip encompasses a selectable single or double conversion design for the receiver and a low power IF upconversion transmitter. All local oscillators are synthesized and integrated into the chip. An on-chip I-Q modulator and demodulator provide baseband modulation and demodulation capability allowing the use of low power, fixed point signal processing components for signal demodulation. The goal of this program is to demonstrate a low cost VDL mode-3 transceiver using this chip to receive text weather information sent using 4-slot TDMA with no support for voice. The data will be sent from an experimental ground station. This work is funded by NASA Glenn Research Center.

Passive noise control by enhancing aeroacoustic interference due to structural discontinuities in close proximity

NASA Astrophysics Data System (ADS)

Leung, R. C. K.; So, R. M. C.; Tang, S. K.; Wang, X. Q.

2011-07-01

In-duct devices are commonly installed in flow ducts for various flow management purposes. The structural construction of these devices indispensably creates disruption to smooth flow through duct passages so they exist as structural discontinuities in duct flow. The presence of these discontinuities provides additional possibility of noise generation. In real practice, in-duct devices do not exist alone in any duct system. Even though each in-duct device would generate its own noise, it might be possible that these devices could be properly arranged so as to strengthen the interference between individual noise; thus giving rise to an overall reduction of noise radiation in the in-duct far field. This concept of passive noise control is investigated by considering different configurations of two structural discontinuities of simple form (i.e., a cavity) in tandem in an unconfined flow and in opposing setting within a flow duct. It is known that noise generated by a cavity in unconfined domain (unconfined cavity) is strongly dependent on flow-resonant behavior within the cavity so the interference it produces is merely aeroacoustic. The objective of the present study is to verify the concept of passive noise reduction through enhancement of aeroacoustic interference due to two cavities by considering laminar flow only. A two-dimensional approach is adopted for the direct aeroacoustic calculations using a direct numerical simulation (DNS) technique. The position and geometries of the cavities and the Mach number are varied; the resultant aeroacoustic behavior and acoustic power are calculated. The numerical results are compared with a single cavity case to highlight the effect of introducing additional cavities to the aeroacoustic problem. Resonant flow oscillations occur when two unconfined cavities are very close and the associated acoustic field is very intense with no noise reduction possible. However, for duct aeroacoustics, it is found that a 7.9 db reduction of acoustic power in the downstream side of the duct or a total reduction of ˜6 db is possible with opposing cavities having an offset of half a cavity length. In addition, the reduction is shown to be free from lock-on with trapped modes of the ducts with cavities.

Transport simulation of EAST long-pulse H-mode discharge with integrated modeling

NASA Astrophysics Data System (ADS)

Wu, M. Q.; Li, G. Q.; Chen, J. L.; Du, H. F.; Gao, X.; Ren, Q. L.; Li, K.; Chan, Vincent; Pan, C. K.; Ding, S. Y.; Jian, X.; Zhu, X.; Lian, H.; Qian, J. P.; Gong, X. Z.; Zang, Q.; Duan, Y. M.; Liu, H. Q.; Lyu, B.

2018-04-01

In the 2017 EAST experimental campaign, a steady-state long-pulse H-mode discharge lasting longer than 100 s has been obtained using only radio frequency heating and current drive, and the confinement quality is slightly better than standard H-mode, H98y2 ~ 1.1, with stationary peaked electron temperature profiles. Integrated modeling of one long-pulse H-mode discharge in the 2016 EAST experimental campaign has been performed with equilibrium code EFIT, and transport codes TGYRO and ONETWO under integrated modeling framework OMFIT. The plasma current is fully-noninductively driven with a combination of ~2.2 MW LHW, ~0.3 MW ECH and ~1.1 MW ICRF. Time evolution of the predicted electron and ion temperature profiles through integrated modeling agree closely with that from measurements. The plasma current (I p ~ 0.45 MA) and electron density are kept constantly. A steady-state is achieved using integrated modeling, and the bootstrap current fraction is ~28%, the RF drive current fraction is ~72%. The predicted current density profile matches the experimental one well. Analysis shows that electron cyclotron heating (ECH) makes large contribution to the plasma confinement when heating in the core region while heating in large radius does smaller improvement, also a more peaked LHW driven current profile is got when heating in the core. Linear analysis shows that the high-k modes instability (electron temperature gradient driven modes) is suppressed in the core region where exists weak electron internal transport barriers. The trapped electron modes dominates in the low-k region, which is mainly responsible for driving the electron energy flux. It is found that the ECH heating effect is very local and not the main cause to sustained the good confinement, the peaked current density profile has the most important effect on plasma confinement improvement. Transport analysis of the long-pulse H-mode experiments on EAST will be helpful to build future experiments.

Surveillance system and method having parameter estimation and operating mode partitioning

NASA Technical Reports Server (NTRS)

Bickford, Randall L. (Inventor)

2003-01-01

A system and method for monitoring an apparatus or process asset including partitioning an unpartitioned training data set into a plurality of training data subsets each having an operating mode associated thereto; creating a process model comprised of a plurality of process submodels each trained as a function of at least one of the training data subsets; acquiring a current set of observed signal data values from the asset; determining an operating mode of the asset for the current set of observed signal data values; selecting a process submodel from the process model as a function of the determined operating mode of the asset; calculating a current set of estimated signal data values from the selected process submodel for the determined operating mode; and outputting the calculated current set of estimated signal data values for providing asset surveillance and/or control.

Alternate charging and discharging of capacitor to enhance the electron production of bioelectrochemical systems.

PubMed

Liang, Peng; Wu, Wenlong; Wei, Jincheng; Yuan, Lulu; Xia, Xue; Huang, Xia

2011-08-01

A bioelectrochemical system (BES) can be operated in both "microbial fuel cell" (MFC) and "microbial electrolysis cell" (MEC) modes, in which power is delivered and invested respectively. To enhance the electric current production, a BES was operated in MFC mode first and a capacitor was used to collect power from the system. Then the charged capacitor discharged electrons to the system itself, switching into MEC mode. This alternate charging and discharging (ACD) mode helped the system produce 22-32% higher average current compared to an intermittent charging (IC) mode, in which the capacitor was first charged from an MFC and then discharged to a resistor, at 21.6 Ω external resistance, 3.3 F capacitance and 300 mV charging voltage. The effects of external resistance, capacitance and charging voltage on average current were studied. The average current reduced as the external resistance and charging voltage increased and was slightly affected by the capacitance. Acquisition of higher average current in the ACD mode was attributed to the shorter discharging time compared to the charging time, as well as a higher anode potential caused by discharging the capacitor. Results from circuit analysis and quantitatively calculation were consistent with the experimental observations.

Influence of pacer continuity on continuous and discontinuous visuo-motor synchronisation.

PubMed

Zelic, Gregory; Varlet, Manuel; Kim, Jeesun; Davis, Chris

2016-09-01

Previous research has reported that synchronising movements with an external pacer, known as sensorimotor synchronisation (SMS), is more stable when the movements are discrete/discontinuous rather than continuous. A standard explanation considers that more efficient mechanisms are involved for regulating synchronisation when producing discontinuous movements. To date, however, only discontinuous pacers (e.g., metronomes) have been investigated to compare discontinuous and continuous SMS. We propose an alternative explanation whereby the discontinuous SMS has benefited from the matching between the (dis)continuous nature of the pacer and the (dis)continuous nature of the movements of synchronisation. The present experiment tested this explanation by examining the relative stability of discontinuous and continuous SMS when synchronising with a continuous pacer. Twelve participants finger tapped (discontinuous SMS) or continuously oscillated their forearm (continuous SMS) in synchrony with an oscillatory visual target. The continuity of the pacer was manipulated by varying the kinematic (harmonic to Rayleigh-like oscillations) and the frequency (0.5 and 1Hz) of the target oscillations. Overall, the results showed a more stable continuous than discontinuous SMS. Furthermore, the stability of the discontinuous SMS improved when increasing the discontinuity of the target displacements (high nonlinear kinematic and low frequency), showing an interaction between movement type and pacer continuity in SMS. Copyright © 2016 Elsevier B.V. All rights reserved.

Some Experimental and Monte Carlo Investigations of the Plastic Scintillators for the Current Mode Measurements at Pulsed Neutron Sources

NASA Astrophysics Data System (ADS)

Rogov, A.; Pepyolyshev, Yu.; Carta, M.; d'Angelo, A.

Scintillation detector (SD) is widely used in neutron and gamma-spectrometry in a count mode. The organic scintillators for the count mode of the detector operation are investigated rather well. Usually, they are applied for measurement of amplitude and time distributions of pulses caused by single interaction events of neutrons or gamma's with scintillator material. But in a large area of scientific research scintillation detectors can alternatively be used on a current mode by recording the average current from the detector. For example,the measurements of the neutron pulse shape at the pulsed reactors or another pulsed neutron sources. So as to get a rather large volume of experimental data at pulsed neutron sources, it is necessary to use the current mode detector for registration of fast neutrons. Many parameters of the SD are changed with a transition from an accounting mode to current one. For example, the detector efficiency is different in counting and current modes. Many effects connected with time accuracy become substantial. Besides, for the registration of solely fast neutrons, as must be in many measurements, in the mixed radiation field of the pulsed neutron sources, SD efficiency has to be determined with a gamma-radiation shield present. Here is no calculations or experimental data on SD current mode operation up to now. The response functions of the detectors can be either measured in high-precision reference fields or calculated by a computer simulation. We have used the MCNP code [1] and carried out some experiments for investigation of the plastic performances in a current mode. There are numerous programs performing simulating similar to the MCNP code. For example, for neutrons there are [2-4], for photons - [5-8]. However, all known codes to use (SCINFUL, NRESP4, SANDYL, EGS49) have more stringent restrictions on the source, geometry and detector characteristics. In MCNP code a lot of these restrictions are absent and you need only to write special additions for proton and electron recoil and transfer energy to light output. These code modifications allow taking into account all processes in organic scintillator influence the light yield.

The homeostatic psyche: Freudian theory and somatic markers.

PubMed

Arminjon, Mathieu; Ansermet, François; Magistretti, Pierre

2010-11-01

After years of reciprocal lack of interest, if not opposition, neuroscience and psychoanalysis are poised for a renewed dialogue. This article discusses some aspects of the Freudian metapsychology and its link with specific biological mechanisms. It highlights in particular how the physiological concept of homeostasis resonates with certain fundamental concepts of psychoanalysis. Similarly, the authors underline how the Freud and Damasio theories of brain functioning display remarkable complementarities, especially through their common reference to Meynert and James. Furthermore, the Freudian theory of drives is discussed in the light of current neurobiological evidences of neural plasticity and trace formation and of their relationships with the processes of homeostasis. The ensuing dynamics between traces and homeostasis opens novel avenues to consider inner life in reference to the establishment of fantasies unique to each subject. The lack of determinism, within a context of determinism, implied by plasticity and reconsolidation participates in the emergence of singularity, the creation of uniqueness and the unpredictable future of the subject. There is a gap in determinism inherent to biology itself. Uniqueness and discontinuity: this should today be the focus of the questions raised in neuroscience. Neuroscience needs to establish the new bases of a "discontinuous" biology. Psychoanalysis can offer to neuroscience the possibility to think of discontinuity. Neuroscience and psychoanalysis meet thus in an unexpected way with regard to discontinuity and this is a new point of convergence between them. Copyright © 2010 Elsevier Ltd. All rights reserved.

Long-term dose-response studies of inhaled or injected radionuclides. Biennial report, 1 October 1991--30 September 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boecker, B.B.; Muggenburg, B.A.; Miller, S.C.

This report describes the scientific progress in, and current status of, life-span studies of the long-term health risks in Beagle dogs of chronic irradiation from internally deposited radionuclides or from an external source. The reporting period for this document is the 2-year period from October 1, 1991 through September 30, 1993. Studies that were initiated at three different laboratories (Inhalation Toxicology Research Institute, ITRI, University of Utah, and Argonne National Laboratory, ANL) are presented here because they are being completed at ITRI. All living dogs in the Utah-initiated studies were transferred to the ITRI facility for the remainder of theirmore » life-span observations and measurements in September 1987. This report is the fourth in a series of reports dealing with the current status and progress of both the Utah and ITRI studies. Other life-span studies involving dogs exposed to gamma radiation from an external source were initiated and conducted for many years at ANL. In 1991, the decision was made to discontinue the chronic irradiation of the remaining living dogs and to transfer all remaining dogs to ITRI for care, clinical observations, and pathological observations at death or euthanasia. This report provides the current status of these dogs. Status reports on the Utah and ITRI studies comprise most of this report. The ITRI-related section presents brief statements of project objectives, the general procedures used in these studies, and some study-specific features for each of the 19 studies being conducted with either beta- or alpha-emitting radionuclides. Dose- and effect-modifying factors being addressed in these studies include total dose, dose rate, LET, solubility, nonuniformity of dose, species, age, sex, health status, and mode of exposure. Recent additions to experimental protocols for studies in which dogs are still alive involve the collection and analysis of tumor tissues using currently available molecular biology techniques.« less

Damping of Quasi-stationary Waves Between Two Miscible Liquids

NASA Technical Reports Server (NTRS)

Duval, Walter M. B.

2002-01-01

Two viscous miscible liquids with an initially sharp interface oriented vertically inside a cavity become unstable against oscillatory external forcing due to Kelvin-Helmholtz instability. The instability causes growth of quasi-stationary (q-s) waves at the interface between the two liquids. We examine computationally the dynamics of a four-mode q-s wave, for a fixed energy input, when one of the components of the external forcing is suddenly ceased. The external forcing consists of a steady and oscillatory component as realizable in a microgravity environment. Results show that when there is a jump discontinuity in the oscillatory excitation that produced the four-mode q-s wave, the interface does not return to its equilibrium position, the structure of the q-s wave remains imbedded between the two fluids over a long time scale. The damping characteristics of the q-s wave from the time history of the velocity field show overdamped and critically damped response; there is no underdamped oscillation as the flow field approaches steady state. Viscous effects serve as a dissipative mechanism to effectively damp the system. The stability of the four-mode q-s wave is dependent on both a geometric length scale as well as the level of background steady acceleration.

Linear lesions in heart tissue using diffused laser radiation

NASA Astrophysics Data System (ADS)

Fried, Nathaniel M.; Lardo, Albert C.; Berger, Ronald D.; Calkins, Hugh; Halperin, Henry R.

2000-05-01

Transmural, continuous, and linear lesions may be necessary for successful catheter ablation of cardiac arrythmias such as atrial fibrillation. Laser ablation was studied as an alternative to radiofrequency ablation, which is noted to produce superficial and discontinuous lesions as well as tissue charring and vaporization. Samples of canine myocardium were placed in a saline bath and irradiated with an 1.06- micrometer Nd:YAG laser operated in either pulsed or continuous mode. For pulsed mode, the laser pulse duration was 10 s with 10 s cooling between pulses. Laser radiation was delivered radially through diffusing optical fiber tips oriented parallel to the endocardial surface. In CW mode, transmural (6-mm-deep), linear (16-mm-long), and continuous lesions were produced using a laser power of 30 W and an irradiation time of 180 s. Peak tissue temperatures measured 51 plus or minus 1 degree Celsius at the endocardial surface, 61 plus or minus 6 degrees Celsius in the mid-myocardium, and 55 plus or minus 6 degree Celsius at the epicardial surface. There was no evidence of tissue charring or vaporization. Pulsed laser irradiation produced comparable lesion depths to CW irradiation with more uniform heating of the subsurface myocardium, but at the expense of longer operation times. Further in vivo study of laser ablation is warranted for possible clinical applications.

Transition Analysis for the HIFiRE-1 Flight Experiment

NASA Technical Reports Server (NTRS)

Li, Fei; Choudhari, Meelan M.; Chang, Chau-Lyan; Kimmel, Roger; Adamczak, David; Smith, Mark S.

2011-01-01

The HIFiRE-1 flight experiment provided a valuable database pertaining to boundary layer transition over a 7-degree half-angle, circular cone model from supersonic to hypersonic Mach numbers, and a range of Reynolds numbers and angles of incidence. This paper reports the initial findings from the ongoing computational analysis pertaining to the measured in-flight transition behavior. Transition during the ascent phase at nearly zero degree angle of attack is dominated by second mode instabilities except in the vicinity of the cone meridian where a roughness element was placed midway along the length of the cone. The first mode instabilities were found to be weak at all trajectory points analyzed from the ascent phase. For times less than approximately 18.5 seconds into the flight, the peak amplification ratio for second mode disturbances is sufficiently small because of the lower Mach numbers at earlier times, so that the transition behavior inferred from the measurements is attributed to an unknown physical mechanism, potentially related to step discontinuities in surface height near the locations of a change in the surface material. Based on the time histories of temperature and/or heat flux at transducer locations within the aft portion of the cone, the onset of transition correlated with a linear PSE N-factor of approximately 14.

Notch strengthening or weakening governed by transition of shear failure to normal mode fracture

PubMed Central

Lei, Xianqi; Li, Congling; Shi, Xinghua; Xu, Xianghong; Wei, Yujie

2015-01-01

It is generally observed that the existence of geometrical discontinuity like notches in materials will lead to strength weakening, as a resultant of local stress concentration. By comparing the influence of notches to the strength of three typical materials, aluminum alloys with intermediate tensile ductility, metallic glasses with no tensile ductility, and brittle ceramics, we observed strengthening in aluminum alloys and metallic glasses: Tensile strength of the net section in circumferentially notched cylinders increases with the constraint quantified by the ratio of notch depth over notch root radius; in contrast, the ceramic exhibit notch weakening. The strengthening in the former two is due to resultant deformation transition: Shear failure occurs in intact samples while samples with deep notches break in normal mode fracture. No such deformation transition was observed in the ceramic, and stress concentration leads to its notch weakening. The experimental results are confirmed by theoretical analyses and numerical simulation. The results reported here suggest that the conventional criterion to use brittleness and/or ductility to differentiate notch strengthening or weakening is not physically sound. Notch strengthening or weakening relies on the existence of failure mode transition and materials exhibiting shear failure while subjected to tension will notch strengthen. PMID:26022892

Efficacy and Acceptability of Glycemic Control of Glucagon-Like Peptide-1 Receptor Agonists among Type 2 Diabetes: A Systematic Review and Network Meta-Analysis.

PubMed

Li, Zhixia; Zhang, Yuan; Quan, Xiaochi; Yang, Zhirong; Zeng, Xiantao; Ji, Linong; Sun, Feng; Zhan, Siyan

2016-01-01

To synthesize current evidence of the impact of Glucagon-like peptide-1 receptor agonists (GLP-1 RAs) on hypoglycemia, treatment discontinuation and glycemic level in patients with type 2 diabetes. Systematic review and network meta-analysis. Literature search (Medline, Embase, the Cochrane library), website of clinical trial, bibliographies of published systematic reviews. Randomized controlled trials with available data comparing GLP-1 RAs with placebo or traditional anti-diabetic drugs in patients with type 2 diabetes. Traditional pairwise meta-analyses within DerSimonian-Laird random effects model and network meta-analysis within a Bayesian framework were performed to calculate odds ratios for the incidence of hypoglycemia, treatment discontinuation, HbA1c<7.0% and HbA1c<6.5%. Ranking probabilities for all treatments were estimated to obtain a treatment hierarchy using the surface under the cumulative ranking curve (SUCRA) and mean ranks. 78 trials with 13 treatments were included. Overall, all GLP-1 RAs except for albiglutide increased the risk of hypoglycemia when compared to placebo. Reduction in the incidence of hypoglycemia was found for all GLP-1 RAs versus insulin (except for dulaglutide) and sulphonylureas. For the incidence of treatment discontinuation, increase was found for exenatide, liraglutide, lixisenatide and taspoglutide versus placebo, insulin and sitagliptin. For glycemic level, decrease was found for all GLP-1 RAs versus placebo. Dulaglutide, exenatide long-acting release (exe_lar), liraglutide and taspoglutide had significant lowering effect when compared with sitagliptin (HbA1c<7.0%) and insulin (HbA1c<6.5%). Finally, according to SUCRAs, placebo, thiazolidinediones and albiglutide had the best decrease effect on hypoglycemia; sulphanylureas, sitagliptin and insulin decrease the incidence of treatment discontinuation most; exe_lar and dulaglutide had the highest impact on glycemic level among 13 treatments. Among 13 treatments, GLP-1 RAs had a significant reduction with glycemic level but a slight increase effect on hypoglycemia and treatment discontinuation. While albiglutide had the best decrease effect on hypoglycemia and treatment discontinuation among all GLP-1 RAs. However, further evidence is necessary for more conclusive inferences on mechanisms underlying the rise in hypoglycemia.

Trapped fast particle destabilization of internal kink mode for the locally flattened q-profile with an inflection point

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Xian-Qu; Zhang, Rui-Bin; Meng, Guo

2016-07-15

The destabilization of ideal internal kink modes by trapped fast particles in tokamak plasmas with a “shoulder”-like equilibrium current is investigated. It is found that energetic particle branch of the mode is unstable with the driving of fast-particle precession drifts and corresponds to a precessional fishbone. The mode with a low stability threshold is also more easily excited than the conventional precessional fishbone. This is different from earlier studies for the same equilibrium in which the magnetohydrodynamic (MHD) branch of the mode is stable. Furthermore, the stability and characteristic frequency of the mode are analyzed by solving the dispersion relationmore » and comparing with the conventional fishbone. The results suggest that an equilibrium with a locally flattened q-profile, may be modified by localized current drive (or bootstrap current, etc.), is prone to the onset of the precessional fishbone branch of the mode.« less

Classical impurities and boundary Majorana zero modes in quantum chains

NASA Astrophysics Data System (ADS)

Müller, Markus; Nersesyan, Alexander A.

2016-09-01

We study the response of classical impurities in quantum Ising chains. The Z2 degeneracy they entail renders the existence of two decoupled Majorana modes at zero energy, an exact property of a finite system at arbitrary values of its bulk parameters. We trace the evolution of these modes across the transition from the disordered phase to the ordered one and analyze the concomitant qualitative changes of local magnetic properties of an isolated impurity. In the disordered phase, the two ground states differ only close to the impurity, and they are related by the action of an explicitly constructed quasi-local operator. In this phase the local transverse spin susceptibility follows a Curie law. The critical response of a boundary impurity is logarithmically divergent and maps to the two-channel Kondo problem, while it saturates for critical bulk impurities, as well as in the ordered phase. The results for the Ising chain translate to the related problem of a resonant level coupled to a 1d p-wave superconductor or a Peierls chain, whereby the magnetic order is mapped to topological order. We find that the topological phase always exhibits a continuous impurity response to local fields as a result of the level repulsion of local levels from the boundary Majorana zero mode. In contrast, the disordered phase generically features a discontinuous magnetization or charging response. This difference constitutes a general thermodynamic fingerprint of topological order in phases with a bulk gap.

The TRacking Adolescents' Individual Lives Survey (TRAILS): Design, Current Status, and Selected Findings

ERIC Educational Resources Information Center

Ormel, Johan; Oldehinkel, Albertine J.; Sijtsema, Jelle; van Oort, Floor; Raven, Dennis; Veenstra, Rene; Vollebergh, Wilma A. M.; Verhulst, Frank C.

2012-01-01

Objectives: The objectives of this study were as follows: to present a concise overview of the sample, outcomes, determinants, non-response and attrition of the ongoing TRacking Adolescents' Individual Lives Survey (TRAILS), which started in 2001; to summarize a selection of recent findings on continuity, discontinuity, risk, and protective…

Romanian Pupils at the Spanish Primary Schools: Continuities and Discontinuities between Former and Current Educational Experiences

ERIC Educational Resources Information Center

Ion, Georgeta

2011-01-01

During the last few years, East-Europeans, predominantly Romanians, have become the second largest cultural minority in Catalonia (Spain). Spanish educational institutions now have students from more than twenty different cultures. This paper focuses on the educational background and the factors which characterize the educational experience of…

Observation of a westward travelling surge from satellites at low, medium and high altitudes

NASA Technical Reports Server (NTRS)

Ungstrup, E.; Sharp, R. D.; Cattell, C. A.; Anderson, R. R.; Fitzenreiter, R. J.; Evans, D. S.; Baker, D. N.

1984-01-01

The motion of discontinuity; electric potential and current structure of the event; energy source and flow; wave-particle interactions; and particle acceleration are addressed using wave, electron, ion mass spectrometer, dc electric field, and magnetic field observation from the Isee-1, NOAA-6, and the 1976-059 geostationary satellite.

The Older Woman: Continuities and Discontinuities.

ERIC Educational Resources Information Center

National Inst. of Mental Health (DHEW), Rockville, MD.

This report on the proceedings of a workshop on the older woman presents purposes of the workshop, including the stimulation of interest by researchers in questions currently relevant to the lives of older women and the generation of future research agenda for the two sponsoring institutes. The following areas of concern are addressed: (1)…

Preparation of ore blocks for mine leaching by reagent explosion injection

NASA Astrophysics Data System (ADS)

Shevchenko, YuS

2017-02-01

The current drilling-and-blasting operations fail to prepare intact ore body underlying a production horizon for subsequent mining and leaching. It is found that the required preparation quality is possible by means of advanced implementation of ore body discontinuity and filling of the resultant system of joints with active leaching solutions.

Detection of Anomalous Machining Damages in Inconel 718 and TI 6-4 by Eddy Current Techniques

NASA Astrophysics Data System (ADS)

Lo, C. C. H.; Shimon, M.; Nakagawa, N.

2010-02-01

This paper reports on an eddy current (EC) study aimed at detecting anomalous machining damages in Inconel 718 and Ti 6-4 samples, including (i) surface discontinuities such as re-depositing of chips onto the machined surface, and (ii) microstructural damages manifested as a white surface layer and a subsurface layer of distorted grains, typically tens of microns thick. A series of pristine and machine-damaged coupons were studied by EC scans using a differential probe operated at 2 MHz to detect discontinuous surface anomalies, and by swept high frequency EC (SHFEC) measurements from 0.5 MHz to 65.5 MHz using proprietary detection coils to detect surface microstructural damages. In general, the EC c-scan data from machine-damaged surfaces show spatial variations with larger standard deviations than those from the undamaged surfaces. In some cases, the c-scan images exhibit characteristic bipolar indications in good spatial correlation with surface anomalies revealed by optical microscopy and laser profilometry. Results of the SHFEC measurements indicate a reduced near-surface conductivity of the damaged surfaces compared to the undamaged surfaces.

Verification of the Polish Geodetic Reference Frame by Means of a New Solution Based on Permanent GNSS Data from the Years 2011-2014

NASA Astrophysics Data System (ADS)

Liwosz, T.; Ryczywolski, M.

2016-12-01

The new solution for the Polish geodetic primary GNSS network was created to verify the currently used reference frame (PL-ETRF2000). The new solution is based on more GNSS data (more daily observation sessions included, a longer data timespan, GLONASS observations added) which were processed in a newer reference frame (IGb08) according to up-to-date methodology and using the latest version of Bernese GNSS Software. The new long-term solution (spanning 3.7 years) was aligned to the IGb08 reference frame using a minimum constraints approach. We categorized Polish reference stations into two categories according to their data length. We obtained good agreement of the new solution with the PL-ETRF2000: for most stations position differences did not exceed 5 mm in horizontal, and 10 mm in vertical components. However, for 30 stations we observed discontinuities in position time series, mostly due to GNSS equipment changes, which occured after the introduction of PL-ETRF2000. Position changes due to the discontinuities reached 9.1 mm in horizontal components, and 26.9 mm in vertical components. The new solution takes into account position discontinuities, and in addition also includes six new stations which were installed after the introduction of the PL-ETRF2000. Therefore, we propose to update the currently-used reference frame for the Polish geodetic primary network (PL-ETRF2000) with the new solution. The new solution was also accepted by the EUREF Technical Working Group as a class A solution (highest accuracy) according to EUREF standards.

Reasons and correlates of contraceptive discontinuation in Kuwait.

PubMed

Shah, N M; Shah, M A; Chowdhury, R I; Menon, I

2007-09-01

(1) To examine the probability of discontinuation of various methods within 1, 2, and three years of use and the reasons for discontinuation; 2) to analyse the socio-demographic correlates of discontinuation. Data from a survey of Kuwaiti women in reproductive ages conducted in 1999 were used. Information on duration of use of modern and traditional methods, and reasons for discontinuation during the 72 months before the survey were analysed. Probabilities of discontinuation were estimated through multiple decrement life table analysis. After 1 year, 30% of modern and 40% of traditional method users had discontinued; after 3 years, discontinuation increased to 66 and 70%, respectively. After 36 months, only 40% of IUD users discontinued compared with 74% of oral contraceptive users. The desire to become pregnant was the leading reason for discontinuation of most modern methods, while method failure was an equally important reason for traditional methods. Discontinuation was significantly more frequent among higher parity, non-working and Bedouin women, and among those who said Islam disapproves of contraception. Contraception is used largely for spacing. More than two-thirds of the women studied had discontinued most methods after three years, except the IUD, which was used only by about 10% of them. Traditional methods are often discontinued due to method failure and may result in an unintended pregnancy. Better counselling is warranted for traditional methods. Health care for managing side effects of modern methods also needs improvement.

40 CFR Appendix II to Part 1042 - Steady-State Duty Cycles

Code of Federal Regulations, 2011 CFR

2011-07-01

... the maximum test power. 3 Advance from one mode to the next within a 20-second transition phase. During the transition phase, command a linear progression from the torque setting of the current mode to... transition phase, command a linear progression from the torque setting of the current mode to the torque...

Nonlinear calculation of the m=1 internal kink instability in current carrying stellarators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wakatani, M.

1978-02-01

Nonlinear properties of the m=1 internal kink mode are shown in a low beta current carrying stellarator. The effects of the external helical magnetic fields are considered through a rotational transform and the magnetic surface is assumed to be circular. Magnetic surfaces inside the iota sub eta + iota sub sigma = 1 surface shift and deform non-circularly, while magnetic surfaces outside the iota sub eta + iota sub sigma = 1 are not disturbed, where iota sub eta is a rotational transform due to helical magnetic fields and iota sub sigma is due to a plasma current. Many highermore » harmonics are excited after the fundamental mode saturates. When the external helical magnetic fields are lowered, the m=1 tearing mode similar to that in a low beta Tokamak grows and magnetic islands appear near the iota sub eta + iota sub sigma = 1 surface. For adequate helical magnetic fields, the current carrying stellarator becomes stable against both the m=1 internal kink mode and the m=1 internal kink mode and the m=1 tearing mode, without lowering the rotational transform.« less

Diagnostic for two-mode variable valve activation device

DOEpatents

Fedewa, Andrew M

2014-01-07

A method is provided for diagnosing a multi-mode valve train device which selectively provides high lift and low lift to a combustion valve of an internal combustion engine having a camshaft phaser actuated by an electric motor. The method includes applying a variable electric current to the electric motor to achieve a desired camshaft phaser operational mode and commanding the multi-mode valve train device to a desired valve train device operational mode selected from a high lift mode and a low lift mode. The method also includes monitoring the variable electric current and calculating a first characteristic of the parameter. The method also includes comparing the calculated first characteristic against a predetermined value of the first characteristic measured when the multi-mode valve train device is known to be in the desired valve train device operational mode.

Alternative model of space-charge-limited thermionic current flow through a plasma

NASA Astrophysics Data System (ADS)

Campanell, M. D.

2018-04-01

It is widely assumed that thermionic current flow through a plasma is limited by a "space-charge-limited" (SCL) cathode sheath that consumes the hot cathode's negative bias and accelerates upstream ions into the cathode. Here, we formulate a fundamentally different current-limited mode. In the "inverse" mode, the potentials of both electrodes are above the plasma potential, so that the plasma ions are confined. The bias is consumed by the anode sheath. There is no potential gradient in the neutral plasma region from resistivity or presheath. The inverse cathode sheath pulls some thermoelectrons back to the cathode, thereby limiting the circuit current. Thermoelectrons entering the zero-field plasma region that undergo collisions may also be sent back to the cathode, further attenuating the circuit current. In planar geometry, the plasma density is shown to vary linearly across the electrode gap. A continuum kinetic planar plasma diode simulation model is set up to compare the properties of current modes with classical, conventional SCL, and inverse cathode sheaths. SCL modes can exist only if charge-exchange collisions are turned off in the potential well of the virtual cathode to prevent ion trapping. With the collisions, the current-limited equilibrium must be inverse. Inverse operating modes should therefore be present or possible in many plasma devices that rely on hot cathodes. Evidence from past experiments is discussed. The inverse mode may offer opportunities to minimize sputtering and power consumption that were not previously explored due to the common assumption of SCL sheaths.

Mode jumping of split-ring resonator metamaterials controlled by high-permittivity BST and incident electric fields

PubMed Central

Fu, Xiaojian; Zeng, Xinxi; Cui, Tie Jun; Lan, Chuwen; Guo, Yunsheng; Zhang, Hao Chi; Zhang, Qian

2016-01-01

We investigate the resonant modes of split-ring resonator (SRR) metamaterials that contain high-permittivity BST block numerically and experimentally. We observe interesting mode-jumping phenomena from the BST-included SRR absorber structure as the excitation wave is incident perpendicularly to the SRR plane. Specifically, when the electric field is parallel to the SRR gap, the BST block in the gap will induce a mode jumping from the LC resonance to plasmonic resonance (horizontal electric-dipole mode), because the displacement current excited by the Mie resonance in the dielectric block acts as a current channel in the gap. When the electric field is perpendicular to the gap side, the plasmonic resonance mode (vertical electric-dipole mode) in SRR changes to two joint modes contributed simultaneously by the back layer, SRR and BST block, as a result of connected back layer and SRR layer by the displacement current in the BST dielectric block. Based on the mode jumping effect as well as temperature and electric-field dependent dielectric constant, the BST-included SRR metamaterials may have great potentials for the applications in electromagnetic switches and widely tunable metamaterial devices. PMID:27502844

Large-Scale Survey of the Structure of the Dayside Magnetopause by MMS

NASA Astrophysics Data System (ADS)

Paschmann, G.; Haaland, S. E.; Phan, T. D.; Sonnerup, B. U. Ö.; Burch, J. L.; Torbert, R. B.; Gershman, D. J.; Dorelli, J. C.; Giles, B. L.; Pollock, C.; Saito, Y.; Lavraud, B.; Russell, C. T.; Strangeway, R. J.; Baumjohann, W.; Fuselier, S. A.

2018-03-01

This paper describes the generation and initial utilization of a database containing 80 vector and scalar quantities, for a total of 8,670 magnetopause and magnetosheath current sheet crossings by MMS1, using plasma and magnetic field data from the Fast Plasma Investigation, Fluxgate Magnetometer, and Hot Plasma Composition Analyzer instruments, augmented by solar wind and interplanetary magnetic field data from CDAWeb. Based on a determination of the current sheet width, measured and calculated vector and scalar quantities are stored for the two sides of the current sheet and for selected times within the current sheet. The only manual operations were the classification of the current sheets according to the type of boundary, the character of the magnetic field transition, and the quality of the current sheet fit. To characterize the database, histograms of selected key quantities are presented. We then give the statistics for the duration, motion, and thicknesses of the magnetopause current sheet, using single-spacecraft techniques for the determination of the normal velocities, obtaining median results of 12.9 s, 38.5 km/s, and 705.4 km, respectively. When scaled to the ion inertial length, the median thickness became 12.6; there were no thicknesses less than one. Next, we apply the Walén relation to find crossings that are rotational discontinuities and thus may indicate ongoing magnetic reconnection. For crossings where the velocities in the outflow region exceed the velocity on the magnetosheath side by at least 250 km/s, 47% meet our rotational discontinuity criteria. If we require the outflow to exceed 250 km/s along the L direction, then the percentage rises to 68%.

Asynchronous communication in spectral-element and discontinuous Galerkin methods for atmospheric dynamics – a case study using the High-Order Methods Modeling Environment (HOMME-homme_dg_branch)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jamroz, Benjamin F.; Klofkorn, Robert

The scalability of computational applications on current and next-generation supercomputers is increasingly limited by the cost of inter-process communication. We implement non-blocking asynchronous communication in the High-Order Methods Modeling Environment for the time integration of the hydrostatic fluid equations using both the spectral-element and discontinuous Galerkin methods. This allows the overlap of computation with communication, effectively hiding some of the costs of communication. A novel detail about our approach is that it provides some data movement to be performed during the asynchronous communication even in the absence of other computations. This method produces significant performance and scalability gains in large-scalemore » simulations.« less

Asynchronous communication in spectral-element and discontinuous Galerkin methods for atmospheric dynamics – a case study using the High-Order Methods Modeling Environment (HOMME-homme_dg_branch)

DOE PAGES

Jamroz, Benjamin F.; Klofkorn, Robert

2016-08-26

The scalability of computational applications on current and next-generation supercomputers is increasingly limited by the cost of inter-process communication. We implement non-blocking asynchronous communication in the High-Order Methods Modeling Environment for the time integration of the hydrostatic fluid equations using both the spectral-element and discontinuous Galerkin methods. This allows the overlap of computation with communication, effectively hiding some of the costs of communication. A novel detail about our approach is that it provides some data movement to be performed during the asynchronous communication even in the absence of other computations. This method produces significant performance and scalability gains in large-scalemore » simulations.« less

Preparation of synaptic plasma membrane and postsynaptic density proteins using a discontinuous sucrose gradient.

PubMed

Bermejo, Marie Kristel; Milenkovic, Marija; Salahpour, Ali; Ramsey, Amy J

2014-09-03

Neuronal subcellular fractionation techniques allow the quantification of proteins that are trafficked to and from the synapse. As originally described in the late 1960's, proteins associated with the synaptic plasma membrane can be isolated by ultracentrifugation on a sucrose density gradient. Once synaptic membranes are isolated, the macromolecular complex known as the post-synaptic density can be subsequently isolated due to its detergent insolubility. The techniques used to isolate synaptic plasma membranes and post-synaptic density proteins remain essentially the same after 40 years, and are widely used in current neuroscience research. This article details the fractionation of proteins associated with the synaptic plasma membrane and post-synaptic density using a discontinuous sucrose gradient. Resulting protein preparations are suitable for western blotting or 2D DIGE analysis.

Switch-off slow shock/rotational discontinuity structures in collisionless magnetic reconnection: What to look for in satellite observations

NASA Astrophysics Data System (ADS)

Innocenti, M. E.; Cazzola, E.; Mistry, R.; Eastwood, J. P.; Goldman, M. V.; Newman, D. L.; Markidis, S.; Lapenta, G.

2017-04-01

In Innocenti et al. (2015) we have observed and characterized for the first time Petschek-like switch-off slow shock/rotational discontinuity (SO-SS/RD) compound structures in a 2-D fully kinetic simulation of collisionless magnetic reconnection. Observing these structures in the solar wind or in the magnetotail would corroborate the possibility that Petschek exhausts develop in collisionless media as a result of single X point collisionless reconnection. Here we highlight their signatures in simulations with the aim of easing their identification in observations. The most notable signatures include a four-peaked ion current profile in the out-of-plane direction, associated ion distribution functions, increased electron and ion anisotropy downstream the SS, and increased electron agyrotropy downstream the RDs.

Propel: A Discontinuous-Galerkin Finite Element Code for Solving the Reacting Navier-Stokes Equations

NASA Astrophysics Data System (ADS)

Johnson, Ryan; Kercher, Andrew; Schwer, Douglas; Corrigan, Andrew; Kailasanath, Kazhikathra

2017-11-01

This presentation focuses on the development of a Discontinuous Galerkin (DG) method for application to chemically reacting flows. The in-house code, called Propel, was developed by the Laboratory of Computational Physics and Fluid Dynamics at the Naval Research Laboratory. It was designed specifically for developing advanced multi-dimensional algorithms to run efficiently on new and innovative architectures such as GPUs. For these results, Propel solves for convection and diffusion simultaneously with detailed transport and thermodynamics. Chemistry is currently solved in a time-split approach using Strang-splitting with finite element DG time integration of chemical source terms. Results presented here show canonical unsteady reacting flow cases, such as co-flow and splitter plate, and we report performance for higher order DG on CPU and GPUs.

Tunable modulation of refracted lamb wave front facilitated by adaptive elastic metasurfaces

NASA Astrophysics Data System (ADS)

Li, Shilong; Xu, Jiawen; Tang, J.

2018-01-01

This letter reports designs of adaptive metasurfaces capable of modulating incoming wave fronts of elastic waves through electromechanical-tuning of their cells. The proposed elastic metasurfaces are composed of arrayed piezoelectric units with individually connected negative capacitance elements that are online tunable. By adjusting the negative capacitances properly, accurately formed, discontinuous phase profiles along the elastic metasurfaces can be achieved. Subsequently, anomalous refraction with various angles can be realized on the transmitted lowest asymmetric mode Lamb wave. Moreover, designs to facilitate planar focal lenses and source illusion devices can also be accomplished. The proposed flexible and versatile strategy to manipulate elastic waves has potential applications ranging from structural fault detection to vibration/noise control.

27 CFR 17.187 - Discontinuance of business.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Discontinuance of business... PRODUCTS Miscellaneous Provisions § 17.187 Discontinuance of business. The manufacturer shall notify TTB when business is to be discontinued. Upon discontinuance of business, a manufacturer's entire stock of...

A CMOS power-efficient low-noise current-mode front-end amplifier for neural signal recording.

PubMed

Wu, Chung-Yu; Chen, Wei-Ming; Kuo, Liang-Ting

2013-04-01

In this paper, a new current-mode front-end amplifier (CMFEA) for neural signal recording systems is proposed. In the proposed CMFEA, a current-mode preamplifier with an active feedback loop operated at very low frequency is designed as the first gain stage to bypass any dc offset current generated by the electrode-tissue interface and to achieve a low high-pass cutoff frequency below 0.5 Hz. No reset signal or ultra-large pseudo resistor is required. The current-mode preamplifier has low dc operation current to enhance low-noise performance and decrease power consumption. A programmable current gain stage is adopted to provide adjustable gain for adaptive signal scaling. A following current-mode filter is designed to adjust the low-pass cutoff frequency for different neural signals. The proposed CMFEA is designed and fabricated in 0.18-μm CMOS technology and the area of the core circuit is 0.076 mm(2). The measured high-pass cutoff frequency is as low as 0.3 Hz and the low-pass cutoff frequency is adjustable from 1 kHz to 10 kHz. The measured maximum current gain is 55.9 dB. The measured input-referred current noise density is 153 fA /√Hz , and the power consumption is 13 μW at 1-V power supply. The fabricated CMFEA has been successfully applied to the animal test for recording the seizure ECoG of Long-Evan rats.

Conception et calibration d'un sonoreacteur pour l'oxydation de la cellulose par le systeme TEMPO/NaOCl/NaBr

NASA Astrophysics Data System (ADS)

Paquin, Michel

Avec le contexte economique actuel dans le domaine des pates et papiers au Canada, l'industrie se doit de diversifier ses produits mis en marche. La fermeture de plus de 20 usines depuis 2005, une baisse du PIB de l'industrie de 1,4 milliard CAD entre 1999--2008, une baisse de la demande de 2,4 %, une diminution du prix de la pate de 20,9 % depuis juillet 2009. La delocalisation du secteur vers l'Asie et l'hemisphere sud sont autant de raisons pour laquelle l'industrie se doit d'etre a l'avant plan de nouvelle technologie a base de fibre de bois. Pour augmenter leur rentabilite, l'industrie se doit de diversifier ses produits dans d'autres secteurs que le simple fabricant de papier impression-ecriture. Sa diversification passe par l'elaboration de nouveaux papiers a valeur ajoutee (papier conducteur, papier bioactif, etc.), par l'utilisation de la biomasse forestiere pour la production d'energie, par l'utilisation de la biomasse forestiere pour l'elaboration d'une plateforme de chimie verte, par l'utilisation de la lignine pour le developpement de polymeres et par l'utilisation de la fibre cellulosique pour la fabrication de nanomateriaux. La fabrication de nanofibrille de cellulose peut devenir un des produits qui servira a diversifier la production des usines de pates et papiers. Les nanofibrilles de cellulose possedent des proprietes mecaniques et chimiques exceptionnelles. Les nanofibrilles de cellulose sont fabriquees a partir d'une oxydation selective de la pate kraft de feuillu avec le systeme TEMPO-NaOCl-NaBr. L'oxydation selective de l'alcool primaire en C6 du monomere de glucose sous forme de carboxylates engendre une modification chimique de la cellulose qui accroit l'hydrophilicite des fibrilles. Suite a cette oxydation, nous devons effectuer une desintegration mecanique de la fibre kraft de feuillu oxydee pour separer les fibrilles. Le processus d'oxydation de la fibre par le systeme TEMPO-NaOCl-NaBr et sa defibrillation par la suite engendre une grande consommation d'energie et de reactif qui rend le procede difficilement accessible au milieu industriel. L'utilisation des ultrasons lors de la reaction d'oxydation permet de reduire de 50% le temps de reaction et d'autant la consommation de produits chimiques. Actuellement le processus d'oxydation s'effectue en mode discontinu pour une quantite de 20 grammes de pate dans un reacteur en verre dans un bain a ultrason. L'objectif principal de ce travail est d'elaborer un sonoreacteur en mode semi-continu afin d'etre en mesure de transferer une reaction d'oxydation du mode discontinu en mode semi-continu. Le transfert de reaction sera effectue en realisant la calibration de l'activite acoustique des deux differents reacteurs, discontinu et semi-continu, par la methode de Weissler. La methode de Weissler quantifie le taux de production radicalaire en mesurant la formation d'iode moleculaire d'une solution aqueuse d'iodure de potassium sous ultrason. Suite a sa calibration, le sonoreacteur pilote (mode semi-continu) a demontre une augmentation de la production radicalaire de 683 % a 170 kHz en comparaison avec l'utilisation d'un bain a ultrason a la meme frequence. Lors de la reaction d'oxydation, la puissance optimale utilisee dans le bain a ultrason a 170 kHz est de 1000 W. La puissance utilisee selon les resultats de calibration obtenue dans le sonoreacteur pilote est de 125 W soit une diminution de l'energie appliquee de 87,5 %. Lors de la reaction d'oxydation, le taux de production des groupements carboxylates est de 2,6 mmol COOH kg/min dans le bain a ultrason et de 6,87 mmol COOH kg/min dans le sonoreacteur pilote soit une augmentation de 164% du taux de formation. Selon les resultats obtenus, l'utilisation d'un sonoreacteur en mode continu peut etre envisageable pour la reaction d'oxydation de la cellulose par le systeme TEMPO-NaOCl-NaBr en industrie au niveau industriel.

Wide single-mode tuning in quantum cascade lasers with asymmetric Mach-Zehnder interferometer type cavities with separately biased arms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Mei C., E-mail: meizheng@princeton.edu; Gmachl, Claire F.; Liu, Peter Q.

2013-11-18

We report on the experimental demonstration of a widely tunable single mode quantum cascade laser with Asymmetric Mach-Zehnder (AMZ) interferometer type cavities with separately biased arms. Current and, consequently, temperature tuning of the two arms of the AMZ type cavity resulted in a single mode tuning range of 20 cm{sup −1} at 80 K in continuous-wave mode operation, a ten-fold improvement from the lasers under a single bias current. In addition, we also observed a five fold increase in the tuning rate as compared to the AMZ cavities controlled by one bias current.

Verification of gyrokinetic particle simulation of current-driven instability in fusion plasmas. I. Internal kink mode

DOE Office of Scientific and Technical Information (OSTI.GOV)

McClenaghan, J.; Lin, Z.; Holod, I.

The gyrokinetic toroidal code (GTC) capability has been extended for simulating internal kink instability with kinetic effects in toroidal geometry. The global simulation domain covers the magnetic axis, which is necessary for simulating current-driven instabilities. GTC simulation in the fluid limit of the kink modes in cylindrical geometry is verified by benchmarking with a magnetohydrodynamic eigenvalue code. Gyrokinetic simulations of the kink modes in the toroidal geometry find that ion kinetic effects significantly reduce the growth rate even when the banana orbit width is much smaller than the radial width of the perturbed current layer at the mode rational surface.

27 CFR 555.128 - Discontinuance of business.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Discontinuance of business... Discontinuance of business. Where an explosive materials business or operations is discontinued and succeeded by... such facts and shall be delivered to the successor. Where discontinuance of the business or operations...

27 CFR 555.128 - Discontinuance of business.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Discontinuance of business... Discontinuance of business. Where an explosive materials business or operations is discontinued and succeeded by... such facts and shall be delivered to the successor. Where discontinuance of the business or operations...

27 CFR 555.128 - Discontinuance of business.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Discontinuance of business... Discontinuance of business. Where an explosive materials business or operations is discontinued and succeeded by... such facts and shall be delivered to the successor. Where discontinuance of the business or operations...

21 CFR 1301.52 - Termination of registration; transfer of registration; distribution upon discontinuance of business.

Code of Federal Regulations, 2010 CFR

2010-04-01

... discontinues business or professional practice. Any registrant who ceases legal existence or discontinues... registration; distribution upon discontinuance of business. 1301.52 Section 1301.52 Food and Drugs DRUG... of registration; transfer of registration; distribution upon discontinuance of business. (a) Except...

Experimental investigation of different regimes of mode-locking in a high repetition rate passively mode-locked semiconductor quantum-dot laser.

PubMed

Kéfélian, Fabien; O'Donoghue, Shane; Todaro, Maria Teresa; McInerney, John; Huyet, Guillaume

2009-04-13

We report experimental investigations on a two-section 16-GHz repetition rate InAs/GaAs quantum dot passively mode-locked laser. Near the threshold current, pseudo-periodic Q-switching with complex dynamics is exhibited. Mode-locking operation regimes characterized by different repetition rates and timing jitter levels are encountered up to twice the threshold current. Evolution of the RF spectrum and optical spectrum with current is compared. The different mode-locked regimes are shown to be associated with different spectral and temporal shapes, ranging from 1.3 to 6 ps. This point is discussed by introducing the existence of two different supermodes. Repetition rate evolution and timing jitter increase is attributed to the coupling between the dominant and the secondary supermodes.

Eddy-Current Detection Of Cracks In Reinforced Carbon/Carbon

NASA Technical Reports Server (NTRS)

Christensen, Scott V.; Koshti, Ajay M.

1995-01-01

Investigations of failures of components made of reinforced carbon/carbon show eddy-current flaw-detection techniques applicable to these components. Investigation focused on space shuttle parts, but applicable to other parts made of carbon/carbon materials. Techniques reveal cracks, too small to be detected visually, in carbon/carbon matrix substrates and in silicon carbide coates on substrates. Also reveals delaminations in carbon/carbon matrices. Used to characterize extents and locations of discontinuities in substrates in situations in which ultrasonic techniques and destructive techniques not practical.

Edge Stability and Performance of the ELM-Free Quiescent H-Mode and the Quiescent Double Barrier Mode on DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

West, W P; Burrell, K H; Casper, T A

2004-12-03

The quiescent H (QH) mode, an edge localized mode (ELM)-free, high-confinement mode, combines well with an internal transport barrier to form quiescent double barrier (QDB) stationary state, high performance plasmas. The QH-mode edge pedestal pressure is similar to that seen in ELMing phases of the same discharge, with similar global energy confinement. The pedestal density in early ELMing phases of strongly pumped counter injection discharges drops and a transition to QH-mode occurs, leading to lower calculated edge bootstrap current. Plasmas current ramp experiment and ELITE code modeling of edge stability suggest that QH-modes lie near an edge current stability boundary.more » At high triangularity, QH-mode discharges operate at higher pedestal density and pressure, and have achieved ITER level values of {beta}{sub PED} and {nu}*. The QDB achieves performance of {alpha}{sub N}H{sub 89} {approx} 7 in quasi-stationary conditions for a duration of 10 tE, limited by hardware. Recently we demonstrated stationary state QDB discharges with little change in kinetic and q profiles (q{sub 0} > 1) for 2 s, comparable to ELMing ''hybrid scenarios'', yet without the debilitating effects of ELMs. Plasma profile control tools, including electron cyclotron heating and current drive and neutral beam heating, have been demonstrated to control simultaneously the q profile development, the density peaking, impurity accumulation and plasma beta.« less

Discontinuous atmospheric pressure interface for mass spectrometry using a solenoid pulse valve.

PubMed

Usmanov, Dilshadbek T; Hiraoka, Kenzo

2016-08-30

For the development of on-site mass spectrometry for security and safety, point-of-care analysis, etc., the gas volume introduced into the vacuum should be reduced to a minimum. To cope with this demand, a discontinuous atmospheric pressure interface using a solenoid pulse valve was developed. The sample gas was introduced discontinuously into the ionization cell with a volume of 0.17 cm(3) . The sampled gas in the cell was ionized by an alternating current (ac) corona discharge. The generated ions were sampled through a 0.25 mm i.d. and 12 mm long nickel capillary into the vacuum of a time-of-flight mass spectrometer. A gas flow rate of ~25 mL/min was achieved with the 1 Hz pulse valve operation and 20 ms valve opening time. Sub-ng limits of detection for less volatile compounds such as explosives and drugs were obtained. Due to its compact size and low gas load to the vacuum, this new interface may be useful for applications in miniaturized mass spectrometry. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Brief Report: PrEP Uptake, Adherence, and Discontinuation Among California YMSM Using Geosocial Networking Applications.

PubMed

Holloway, Ian W; Dougherty, Ryan; Gildner, Jennifer; Beougher, Sean C; Pulsipher, Craig; Montoya, Jorge A; Plant, Aaron; Leibowitz, Arleen

2017-01-01

We investigated pre-exposure prophylaxis (PrEP) uptake, adherence, and discontinuation among young app-using men who have sex with men in California (N = 761). Approximately, 9.7% of participants had ever used PrEP; 87% of those deemed good candidates for screening (indicated by a Centers for Disease Control and Prevention risk index score ≥10) were not current or past users. PrEP use was associated with higher income [adjusted odds ratio (aOR): 4.13; confidence interval (CI): 1.87 to 9.12], receptive condomless anal sex (aOR: 3.41; CI: 1.71 to 6.78), HIV-positive sex partners (aOR: 2.87; CI: 1.53 to 5.38), popper use (aOR: 3.47; CI: 1.96 to 6.13), and recent sexually transmitted infection diagnosis (aOR: 2.90; CI: 1.64 to 5.13). Some users (41.5%) wanted help remembering to take PrEP. The top reason for discontinuation was concern about long-term side effects (33.0%). Young men who have sex with men app users are prime candidates for PrEP, despite low uptake. Apps may be useful tools for PrEP information dissemination, adherence monitoring, and support.

Formation of magnetic discontinuities through viscous relaxation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Sanjay; Bhattacharyya, R.; Smolarkiewicz, P. K.

2014-05-15

According to Parker's magnetostatic theorem, tangential discontinuities in magnetic field, or current sheets (CSs), are generally unavoidable in an equilibrium magnetofluid with infinite electrical conductivity and complex magnetic topology. These CSs are due to a failure of a magnetic field in achieving force-balance everywhere and preserving its topology while remaining in a spatially continuous state. A recent work [Kumar, Bhattacharyya, and Smolarkiewicz, Phys. Plasmas 20, 112903 (2013)] demonstrated this CS formation utilizing numerical simulations in terms of the vector magnetic field. The magnetohydrodynamic simulations presented here complement the above work by demonstrating CS formation by employing a novel approach ofmore » describing the magnetofluid evolution in terms of magnetic flux surfaces instead of the vector magnetic field. The magnetic flux surfaces being the possible sites on which CSs develop, this approach provides a direct visualization of the CS formation, helpful in understanding the governing dynamics. The simulations confirm development of tangential discontinuities through a favorable contortion of magnetic flux surfaces, as the magnetofluid undergoes a topology-preserving viscous relaxation from an initial non-equilibrium state with twisted magnetic field. A crucial finding of this work is in its demonstration of CS formation at spatial locations away from the magnetic nulls.« less

Heating of the corona by magnetic singularities

NASA Technical Reports Server (NTRS)

Antiochos, Spiro K.

1990-01-01

Theoretical models of current-sheet formation and magnetic heating in the solar corona are examined analytically. The role of photospheric connectivity in determining the topology of the coronal magnetic field and its equilibrium properties is explored; nonequilibrium models of current-sheet formation (assuming an initially well connected field) are described; and particular attention is given to models with discontinuous connectivity, where magnetic singularities arise from smooth footpoint motions. It is shown that current sheets arise from connectivities in which the photospheric flux structure is complex, with three or more polarity regions and a magnetic null point within the corona.

Exact joint density-current probability function for the asymmetric exclusion process.

PubMed

Depken, Martin; Stinchcombe, Robin

2004-07-23

We study the asymmetric simple exclusion process with open boundaries and derive the exact form of the joint probability function for the occupation number and the current through the system. We further consider the thermodynamic limit, showing that the resulting distribution is non-Gaussian and that the density fluctuations have a discontinuity at the continuous phase transition, while the current fluctuations are continuous. The derivations are performed by using the standard operator algebraic approach and by the introduction of new operators satisfying a modified version of the original algebra. Copyright 2004 The American Physical Society

Single-molecule electronics: Cooling individual vibrational modes by the tunneling current.

PubMed

Lykkebo, Jacob; Romano, Giuseppe; Gagliardi, Alessio; Pecchia, Alessandro; Solomon, Gemma C

2016-03-21

Electronic devices composed of single molecules constitute the ultimate limit in the continued downscaling of electronic components. A key challenge for single-molecule electronics is to control the temperature of these junctions. Controlling heating and cooling effects in individual vibrational modes can, in principle, be utilized to increase stability of single-molecule junctions under bias, to pump energy into particular vibrational modes to perform current-induced reactions, or to increase the resolution in inelastic electron tunneling spectroscopy by controlling the life-times of phonons in a molecule by suppressing absorption and external dissipation processes. Under bias the current and the molecule exchange energy, which typically results in heating of the molecule. However, the opposite process is also possible, where energy is extracted from the molecule by the tunneling current. Designing a molecular "heat sink" where a particular vibrational mode funnels heat out of the molecule and into the leads would be very desirable. It is even possible to imagine how the vibrational energy of the other vibrational modes could be funneled into the "cooling mode," given the right molecular design. Previous efforts to understand heating and cooling mechanisms in single molecule junctions have primarily been concerned with small models, where it is unclear which molecular systems they correspond to. In this paper, our focus is on suppressing heating and obtaining current-induced cooling in certain vibrational modes. Strategies for cooling vibrational modes in single-molecule junctions are presented, together with atomistic calculations based on those strategies. Cooling and reduced heating are observed for two different cooling schemes in calculations of atomistic single-molecule junctions.

27 CFR 478.57 - Discontinuance of business.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Discontinuance of business... Licenses § 478.57 Discontinuance of business. (a) Where a firearm or ammunition business is either discontinued or succeeded by a new owner, the owner of the business discontinued or succeeded shall within 30...

27 CFR 478.127 - Discontinuance of business.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Discontinuance of business... Records § 478.127 Discontinuance of business. Where a licensed business is discontinued and succeeded by a... be delivered to the successor. Where discontinuance of the business is absolute, the records shall be...

27 CFR 478.57 - Discontinuance of business.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2014-04-01 2014-04-01 false Discontinuance of business... Licenses § 478.57 Discontinuance of business. (a) Where a firearm or ammunition business is either discontinued or succeeded by a new owner, the owner of the business discontinued or succeeded shall within 30...

27 CFR 478.127 - Discontinuance of business.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Discontinuance of business... Records § 478.127 Discontinuance of business. Where a licensed business is discontinued and succeeded by a... be delivered to the successor. Where discontinuance of the business is absolute, the records shall be...

27 CFR 478.57 - Discontinuance of business.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 3 2013-04-01 2013-04-01 false Discontinuance of business... Licenses § 478.57 Discontinuance of business. (a) Where a firearm or ammunition business is either discontinued or succeeded by a new owner, the owner of the business discontinued or succeeded shall within 30...

39 CFR 241.3 - Discontinuance of USPS-operated retail facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 39 Postal Service 1 2013-07-01 2013-07-01 false Discontinuance of USPS-operated retail facilities... ESTABLISHMENT CLASSIFICATION, AND DISCONTINUANCE § 241.3 Discontinuance of USPS-operated retail facilities. (a... of whether an existing retail Post Office, station, or branch should be discontinued. The rules cover...

39 CFR 241.3 - Discontinuance of USPS-operated retail facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 39 Postal Service 1 2014-07-01 2014-07-01 false Discontinuance of USPS-operated retail facilities... ESTABLISHMENT CLASSIFICATION, AND DISCONTINUANCE § 241.3 Discontinuance of USPS-operated retail facilities. (a... of whether an existing retail Post Office, station, or branch should be discontinued. The rules cover...

39 CFR 241.3 - Discontinuance of USPS-operated retail facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 39 Postal Service 1 2012-07-01 2012-07-01 false Discontinuance of USPS-operated retail facilities... ESTABLISHMENT CLASSIFICATION, AND DISCONTINUANCE § 241.3 Discontinuance of USPS-operated retail facilities. (a... of whether an existing retail Post Office, station, or branch should be discontinued. The rules cover...

Impact of bootstrap current and Landau-fluid closure on ELM crashes and transport

NASA Astrophysics Data System (ADS)

Chen, J. G.; Xu, X. Q.; Ma, C. H.; Lei, Y. A.

2018-05-01

Results presented here are from 6-field Landau-Fluid simulations using shifted circular cross-section tokamak equilibria on BOUT++ framework. Linear benchmark results imply that the collisional and collisionless Landau resonance closures make a little difference on linear growth rate spectra which are quite close to the results with the flux limited Spitzer-Härm parallel flux. Both linear and nonlinear simulations show that the plasma current profile plays dual roles on the peeling-ballooning modes that it can drive the low-n peeling modes and stabilize the high-n ballooning modes. For fixed total pressure and current, as the pedestal current decreases due to the bootstrap current which becomes smaller when the density (collisionality) increases, the operational point is shifted downwards vertically in the Jped - α diagram, resulting in threshold changes of different modes. The bootstrap current can slightly increase radial turbulence spreading range and enhance the energy and particle transports by increasing the perturbed amplitude and broadening cross-phase frequency distribution.

Acceleration Modes and Transitions in Pulsed Plasma Accelerators

NASA Technical Reports Server (NTRS)

Polzin, Kurt A.; Greve, Christine M.

2018-01-01

Pulsed plasma accelerators typically operate by storing energy in a capacitor bank and then discharging this energy through a gas, ionizing and accelerating it through the Lorentz body force. Two plasma accelerator types employing this general scheme have typically been studied: the gas-fed pulsed plasma thruster and the quasi-steady magnetoplasmadynamic (MPD) accelerator. The gas-fed pulsed plasma accelerator is generally represented as a completely transient device discharging in approximately 1-10 microseconds. When the capacitor bank is discharged through the gas, a current sheet forms at the breech of the thruster and propagates forward under a j (current density) by B (magnetic field) body force, entraining propellant it encounters. This process is sometimes referred to as detonation-mode acceleration because the current sheet representation approximates that of a strong shock propagating through the gas. Acceleration of the initial current sheet ceases when either the current sheet reaches the end of the device and is ejected or when the current in the circuit reverses, striking a new current sheet at the breech and depriving the initial sheet of additional acceleration. In the quasi-steady MPD accelerator, the pulse is lengthened to approximately 1 millisecond or longer and maintained at an approximately constant level during discharge. The time over which the transient phenomena experienced during startup typically occur is short relative to the overall discharge time, which is now long enough for the plasma to assume a relatively steady-state configuration. The ionized gas flows through a stationary current channel in a manner that is sometimes referred to as the deflagration-mode of operation. The plasma experiences electromagnetic acceleration as it flows through the current channel towards the exit of the device. A device that had a short pulse length but appeared to operate in a plasma acceleration regime different from the gas-fed pulsed plasma accelerators was developed by Cheng, et al. The Coaxial High ENerGy (CHENG) thruster operated on the 10-microseconds timescales of pulsed plasma thrusters, but claimed high thrust density, high efficiency and low electrode erosion rates, which are more consistent with the deflagration mode of acceleration. Separate work on gas-fed pulsed plasma thrusters (PPTs) by Ziemer, et al. identified two separate regimes of performance. The regime at higher mass bits (termed Mode I in that work) possessed relatively constant thrust efficiency (ratio of jet kinetic energy to input electrical energy) as a function of mass bit. In the second regime at very low mass bits (termed Mode II), the efficiency increased with decreasing mass bit. Work by Poehlmann et al. and by Sitaraman and Raja sought to understand the performance of the CHENG thruster and the Mode I / Mode II performance in PPTs by modeling the acceleration using the Hugoniot Relation, with the detonation and deflagration modes representing two distinct sets of solutions to the relevant conservation laws. These works studied the proposal that, depending upon the values of the various controllable parameters, the accelerator would operate in either the detonation or deflagration mode. In the present work, we propose a variation on the explanation for the differences in performance between the various pulsed plasma accelerators. Instead of treating the accelerator as if it were only operating in one mode or the other during a pulse, we model the initial stage of the discharge in all cases as an accelerating current sheet (detonation mode). If the current sheet reaches the exit of the accelerator before the discharge is completed, the acceleration mode transitions to the deflagration mode type found in the quasi-steady MPD thrusters. This modeling method is used to demonstrate that standard gas-fed pulsed plasma accelerators, the CHENG thruster, and the quasi-steady MPD accelerator are variations of the same device, with the overall acceleration of the plasma depending upon the behavior of the plasma discharge during initial transient phase and the relative lengths of the detonation and deflagration modes of operation.

Anticrack inclusion model for compaction bands in sandstone

NASA Astrophysics Data System (ADS)

Sternlof, Kurt R.; Rudnicki, John W.; Pollard, David D.

2005-11-01

Detailed observations of compaction bands exposed in the Aztec Sandstone of southeastern Nevada indicate that these thin, tabular, bounded features of localized porosity loss initiated at pervasive grain-scale flaws, which collapsed in response to compressive tectonic loading. From many of these Griffith-type flaws, an apparently self-sustaining progression of collapse propagated outward to form bands of compacted grains a few centimeters thick and tens of meters in planar extent. These compaction bands can be idealized as highly eccentric ellipsoidal bodies that have accommodated uniform uniaxial plastic strain parallel to their short dimension within a surrounding elastic material. They thus can be represented mechanically as contractile Eshelby inclusions, which generate near-tip compressive stress concentrations consistent with self-sustaining, in-plane propagation. The combination of extreme aspect ratio (˜10-4) and significant uniaxial plastic strain (˜10%) also justifies an approximation of the bands as anticracks: sharp boundaries across which a continuous distribution of closing mode displacement discontinuity has been accommodated. This anticrack interpretation of compaction bands is analogous to that of pressure solution surfaces, except that porosity loss takes the place of material dissolution. We find that displacement discontinuity boundary element modeling of compaction bands as anticracks within a two-dimensional linear elastic continuum can accurately represent the perturbed external stress fields they induce.

Mechanical properties of simulated Mars materials: gypsum-rich sandstones and lapilli tuff

USGS Publications Warehouse

Morrow, Carolyn; Lockner, David; Okubo, Chris

2013-01-01

Observations by the Mars Exploration Rover (MER) Opportunity, and other recent studies on diagenesis in the extensive equatorial layered deposits on Mars, suggest that the likely lithologies of these deposits are gypsum-rich sandstones and tuffaceous sediments (for example, Murchie and others, 2009; Squyres and others, 2012; Zimbelman and Scheidt, 2012). Of particular interest is how the diagenesis history of these sediments (degree of cementation and composition) influences the strength and brittle behavior of the material. For instance, fractures are more common in lower porosity materials under strain, whereas deformation bands, characterized by distributed strain throughout a broader discontinuity in a material, are common in higher porosity sedimentary materials. Such discontinuities can either enhance or restrict fluid flow; hence, failure mode plays an important role in determining the mechanics of fluid migration through sediments (Antonellini and Aydin, 1994; 1995; Taylor and Pollard, 2000; Ogilvie and Glover, 2001). As part of a larger study to characterize processes of fault-controlled fluid flow in volcaniclastic and gypsum-rich sediments on Mars, we have completed a series of laboratory experiments to focus on how gypsum clast content and degree of authigenic cementation affects the strength behavior of simulated Mars rocks. Both axial deformation and hydrostatic pressure tests were done at room temperature under dry conditions.

Exploring continuous and integrated strategies for the up- and downstream processing of human mesenchymal stem cells.

PubMed

Cunha, Bárbara; Aguiar, Tiago; Silva, Marta M; Silva, Ricardo J S; Sousa, Marcos F Q; Pineda, Earl; Peixoto, Cristina; Carrondo, Manuel J T; Serra, Margarida; Alves, Paula M

2015-11-10

The integration of up- and downstream unit operations can result in the elimination of hold steps, thus decreasing the footprint, and ultimately can create robust closed system operations. This type of design is desirable for the bioprocess of human mesenchymal stem cells (hMSC), where high numbers of pure cells, at low volumes, need to be delivered for therapy applications. This study reports a proof of concept of the integration of a continuous perfusion culture in bioreactors with a tangential flow filtration (TFF) system for the concentration and washing of hMSC. Moreover, we have also explored a continuous alternative for concentrating hMSC. Results show that expanding cells in a continuous perfusion operation mode provided a higher expansion ratio, and led to a shift in cells' metabolism. TFF operated either in continuous or discontinuous allowed to concentrate cells, with high cell recovery (>80%) and viability (>95%); furthermore, continuous TFF permitted to operate longer with higher cell concentrations. Continuous diafiltration led to higher protein clearance (98%) with lower cell death, when comparing to discontinuous diafiltration. Overall, an integrated process allowed for a shorter process time, recovering 70% of viable hMSC (>95%), with no changes in terms of morphology, immunophenotype, proliferation capacity and multipotent differentiation potential. Copyright © 2015 Elsevier B.V. All rights reserved.

Capillary red blood cell velocimetry by phase-resolved optical coherence tomography

NASA Astrophysics Data System (ADS)

Tang, Jianbo; Erdener, Sefik Evren; Fu, Buyin; Boas, David A.

2018-02-01

Quantitative measurement of blood flow velocity in capillaries is challenging due to their small size (around 5-10 μm), and the discontinuity and single-file feature of RBCs flowing in a capillary. In this work, we present a phase-resolved Optical Coherence Tomography (OCT) method for accurate measurement of the red blood cell (RBC) speed in cerebral capillaries. To account for the discontinuity of RBCs flowing in capillaries, we applied an M-mode scanning strategy that repeated A-scans at each scanning position for an extended time. As the capillary size is comparable to the OCT resolution size (3.5×3.5×3.5μm), we applied a high pass filter to remove the stationary signal component so that the phase information of the dynamic component (i.e. from the moving RBC) could be enhanced to provide an accurate estimate of the RBC axial speed. The phase-resolved OCT method accurately quantifies the axial velocity of RBC's from the phase shift of the dynamic component of the signal. We validated our measurements by RBC passage velocimetry using the signal magnitude of the same OCT time series data. These proposed method of capillary velocimetry proved to be a robust method of mapping capillary RBC speeds across the micro-vascular network.

Single-Mode VCSELs

NASA Astrophysics Data System (ADS)

Larsson, Anders; Gustavsson, Johan S.

The only active transverse mode in a truly single-mode VCSEL is the fundamental mode with a near Gaussian field distribution. A single-mode VCSEL produces a light beam of higher spectral purity, higher degree of coherence and lower divergence than a multimode VCSEL and the beam can be more precisely shaped and focused to a smaller spot. Such beam properties are required in many applications. In this chapter, after discussing applications of single-mode VCSELs, we introduce the basics of fields and modes in VCSELs and review designs implemented for single-mode emission from VCSELs in different materials and at different wavelengths. This includes VCSELs that are inherently single-mode as well as inherently multimode VCSELs where higher-order modes are suppressed by mode selective gain or loss. In each case we present the current state-of-the-art and discuss pros and cons. At the end, a specific example with experimental results is provided and, as a summary, the most promising designs based on current technologies are identified.

Spatial variability of damage around faults in the Joe Lott Tuff Member of the Mount Belknap Volcanics, southwestern Utah

NASA Astrophysics Data System (ADS)

Okubo, C. H.

2012-12-01

In order to yield new insight into the process of faulting in fine-grained, poorly indurated volcanic ash, the distribution of strain around faults in the Miocene-aged Joe Lott Tuff Member of the Mount Belknap Volcanics, Utah, is investigated. Several distinct styles of inelastic strain are identified. Deformation bands are observed in tuff that is porous and granular in nature, or is inferred to have been so at the time of deformation. Where silicic alteration is pervasive, fractures are the dominant form of localized strain. Non-localized strain within the host rock is manifest as pore space compaction, including crushing of pumice clasts. Distinct differences in fault zone architecture are observed at different magnitudes of normal fault displacement, in the mode II orientation. A fault with cm-scale displacements is manifest as a single well-defined surface. Off-fault damage occurs as pore space compaction near the fault tips and formation of deformation band damage zones that are roughly symmetric about the fault. At a fault with larger meter-scale displacements, a fault core is present. A recognizable fault-related deformation band damage zone is not observed here, even though large areas of the host rock remain porous and granular and deformation bands had formed prior to faulting. The host rock is instead fractured in areas of pervasive alteration and shows possible textural evidence of fault pulverization. The zones of localized and distributed strain have notably different spatial extents around the causative fault. The region of distributed deformation, as indicated by changes in gas permeability of the macroscopically intact rock, extends up to four times farther from the fault than the highest densities of localized deformation (i.e., fractures and deformation bands). This study identifies a set of fault-related processes that are pertinent to understanding the evolution of fault systems in poorly indurated tuff. Not surprisingly, the type of structural discontinuity that forms in the fault environment is found to be a function of the porosity and granularity of the host rock. Non-localized deformation in the form of pore space compaction of the host rock is found to be prominent around the fault tips at First Spring Hollow. Interestingly, the spatial distribution of host rock compaction and the occurrences of dilational deformation bands around this fault do not correlate with the classic pattern of compression and dilation generally anticipated for slipped normal faults when viewed in mode II. Therefore, while broad generalities regarding the types of discontinuities that form around faults in tuff can be drawn based on current principles, additional work is needed to better understand the genesis of the observed spatial distributions of strain.

Determinants of neonatal weight loss in term-infants: specific association with pre-pregnancy maternal body mass index and infant feeding mode.

PubMed

Regnault, Nolwenn; Botton, Jérémie; Blanc, Laurence; Hankard, Régis; Forhan, Anne; Goua, Valérie; Thiebaugeorges, Olivier; Kaminski, Monique; Heude, Barbara; Charles, Marie-Aline

2011-05-01

We aimed to study the determinants of neonatal weight loss measured on the third day of life in term-infants. The EDEN mother-child cohort is a prospective study that recruited 2002 pregnant women before 24 weeks of gestation in two French university hospitals. Neonates were weighed every day until discharge that occurred on average 4.5 days after birth. Altogether, 1557 healthy term neonates with data on weight at day 3 and feeding mode available were included. The outcome variable was weight loss at day 3 (D3WL), expressed as a percentage of birth weight lost in the first 3 days of life. Our main explanatory variables were maternal pre-pregnancy body mass index (BMI), gestational weight gain, gestational diabetes, birth weight, gestational age and feeding mode. Factors associated with greater D3WL, whatever the feeding mode, were: higher birth weight, gestational diabetes and caesarean section; higher gestational age was associated with a reduced D3WL. The association between maternal pre-pregnancy BMI and D3WL differed by feeding mode (interaction p value=0.0002). In breastfed babies, mean D3WL ranged from 4.9% for neonates of underweight mothers to 5.8% for neonates of obese mothers (p trend=0.0005). In formula-fed babies, D3WL was highest for neonates of underweight mothers (4.1%) and lowest for those of obese mothers (2.6%) (p trend=0.01). The lower D3WL in formula-fed neonates, especially in neonates of obese mothers, suggests a relative overfeeding in the early days compared with breastfed neonates, which may potentially have consequences on later health. Overweight and obese mothers may need extra support to prevent early breastfeeding discontinuation.

Evaluation and optimization of the new EBT2 radiochromic film dosimetry system for patient dose verification in radiotherapy

NASA Astrophysics Data System (ADS)

Richley, L.; John, A. C.; Coomber, H.; Fletcher, S.

2010-05-01

A new radiochromic film, the yellow Gafchromic EBT2, has been marketed as a drop-in replacement for the discontinued blue EBT film. In order to verify the manufacturer's claims prior to clinical use, EBT2 was characterized in transmission, and the less commonly used, reflection modes with an Epson Expression 10000XL A3 flatbed scanner. The red channel was confirmed to provide the greatest sensitivity and was used for all measurements. The post-irradiation darkening of the film was investigated, and the relative response was found to be dose dependent with higher doses stabilizing earlier than lower doses. After 13 h all dose levels had stabilized to within 1% of their value at 24 h. Uniformity of irradiated EBT2 films was within 0.8% and 1.2% (2SD of signal), in reflection and transmission modes, respectively. The light scattering effect, arising from the structure and thickness of EBT2, was found to give rise to an apparent scanner non-uniformity of up to 5.5% in signal. In reflection mode, differences of up to 1.2% were found between the signal obtained from a small film fragment (5 × 5 cm2) and the signal obtained from the same fragment bordered by extra film. Further work is needed to determine the origin of this effect, as there will be implications for reflection dosimetry of intensity modulated fields; reflection mode cannot yet be regarded as a viable alternative to transmission mode. Our results suggest that EBT2 film is a valid alternative, rather than a direct replacement for EBT film.

Toroidal Rotation and 3D Nonlinear Dynamics in the Peeling-Ballooning Model of ELMs

NASA Astrophysics Data System (ADS)

Snyder, P. B.

2004-11-01

Maximizing the height of the edge transport barrier (or ``pedestal'') while maintaining acceptably small edge localized modes (ELMs) is a critical issue for tokamak performance. The peeling-ballooning model proposes that intermediate wavelength MHD instabilities are responsible for ELMs and impose constraints on the pedestal. Recent studies of linear peeling-ballooning stability have found encouraging agreement with observations [e.g. 1]. To allow more detailed prediction of mode characteristics, including eventually predictions of the ELM energy loss and its deposition, we consider effects of sheared toroidal rotation, as well as 3D nonlinear dynamics. An eigenmode formulation for toroidal rotation shear is developed and incorporated into the framework of the ELITE stability code [2], resolving the low rotation discontinuity in previous high-n results. Rotation shear is found to impact the structure of peeling-ballooning modes, causing radial narrowing and mode shearing. The calculated mode frequency is found to agree with observed rotation in the edge region in the early stages of the ELM crash. Nonlinear studies with the 3D BOUT and NIMROD codes reveal detailed characteristics of the early evolution of these edge instabilities, including the impact of non-ideal effects. The expected linear growth phase is followed by a fast crash event in which poloidally narrow, filamentary structures propagate radially outward from the pedestal region, closely resembling observed ELM events. Comparisons with ELM observations will be discussed. \\vspace0.25em [1] P.B. Snyder et al., Nucl. Fusion 44, 320 (2004); P.B. Snyder et al., Phys. Plasmas 9, 2037 (2002). [2] H.R. Wilson et al., Phys. Plasmas 9, 1277 (2002).

Determinants of Breastfeeding Practices and Success in a Multi-Ethnic Asian Population.

PubMed

Pang, Wei Wei; Aris, Izzuddin M; Fok, Doris; Soh, Shu-E; Chua, Mei Chien; Lim, Sok Bee; Saw, Seang-Mei; Kwek, Kenneth; Gluckman, Peter D; Godfrey, Keith M; van Dam, Rob M; Kramer, Michael S; Chong, Yap-Seng

2016-03-01

Many countries in Asia report low breastfeeding rates and the risk factors for early weaning are not well studied. We assessed the prevalence, duration, and mode of breastfeeding (direct or expressed) among mothers of three Asian ethnic groups. Participants were 1,030 Singaporean women recruited during early pregnancy. Data collected included early breastfeeding experiences, breastfeeding duration, and mode of breastfeeding. Full breastfeeding was defined as the intake of breast milk, with or without water. Cox regression models were used to identify factors associated with discontinuation of any and full breastfeeding. Logistic regression analyses assessed the association of ethnicity with mode of breastfeeding. At 6 months postpartum, the prevalence of any breastfeeding was 46 percent for Chinese mothers, 22 percent for Malay mothers, and 41 percent for Indian mothers; prevalence of full breastfeeding was 11, 2, and 5 percent, respectively. More Chinese mothers fed their infants expressed breast milk, instead of directly breastfeeding them, compared with the other two ethnic groups. Duration of any and full breastfeeding were positively associated with breastfeeding a few hours after birth, higher maternal age and education, and negatively associated with irregular breastfeeding frequency and being shown how to breastfeed. Adjusting for maternal education, breastfeeding duration was similar in the three ethnic groups, but ethnicity remained a significant predictor of mode of breastfeeding. The low rates and duration of breastfeeding in this population may be improved with breastfeeding education and support, especially in mothers with lower education. Further work is needed to understand the cultural differences in mode of feeding and its implications for maternal and infant health. © 2015 Wiley Periodicals, Inc.

Predictors of discontinuation of antipsychotic medication and subsequent outcomes in the European First Episode Schizophrenia Trial (EUFEST).

PubMed

Landolt, Karin; Rössler, Wulf; Ajdacic-Gross, Vladeta; Derks, Eske M; Libiger, Jan; Kahn, René S; Fleischhacker, W Wolfgang

2016-04-01

This study had two aims: to describe patients suffering from first-episode schizophrenia who had stopped taking any antipsychotic medication, and to gain information on the predictors of successful discontinuation. We investigated data from the European First Episode Schizophrenia Trial (EUFEST). From the 325 patients included, 15.7% discontinued all antipsychotic medication. In a first analysis, clinical and sociodemographical predictors of discontinuing any antipsychotic medication were identified, using Cox regression. In the second analysis, logistic regression was used to determine variables associated with those patients who had stopped taking antipsychotic medication and had a favourable outcome, i.e., successful discontinuation. A good outcome was defined as a) having had no relapse within the whole observation period (80.6%), and b) having had no relapse and symptomatic remission at 12-month-follow-up (37.2%). Cox regression revealed that a higher proportion of patients from Western European countries and Israel stopped antipsychotic medication than from Central and Eastern European countries, that relapse was associated with discontinuation, and that discontinuers had lower compliance and higher quality of life. Predictors of successful discontinuation differed with the outcome definition used. Using definition b), successful discontinuers had a better baseline prognosis and better baseline social integration. Using definition a), successful discontinuers more often were from Western European countries. Region and clinical factors were associated with discontinuation. Prognosis and social integration played an important role in predicting successful discontinuation. As this study had several limitations, for example the observational design regarding discontinuation, further studies are needed to identify predictors of successful discontinuation. Copyright © 2016 Elsevier B.V. All rights reserved.

High-order dynamic modeling and parameter identification of structural discontinuities in Timoshenko beams by using reflection coefficients

NASA Astrophysics Data System (ADS)

Fan, Qiang; Huang, Zhenyu; Zhang, Bing; Chen, Dayue

2013-02-01

Properties of discontinuities, such as bolt joints and cracks in the waveguide structures, are difficult to evaluate by either analytical or numerical methods due to the complexity and uncertainty of the discontinuities. In this paper, the discontinuity in a Timoshenko beam is modeled with high-order parameters and then these parameters are identified by using reflection coefficients at the discontinuity. The high-order model is composed of several one-order sub-models in series and each sub-model consists of inertia, stiffness and damping components in parallel. The order of the discontinuity model is determined based on the characteristics of the reflection coefficient curve and the accuracy requirement of the dynamic modeling. The model parameters are identified through the least-square fitting iteration method, of which the undetermined model parameters are updated in iteration to fit the dynamic reflection coefficient curve with the wave-based one. By using the spectral super-element method (SSEM), simulation cases, including one-order discontinuities on infinite- and finite-beams and a two-order discontinuity on an infinite beam, were employed to evaluate both the accuracy of the discontinuity model and the effectiveness of the identification method. For practical considerations, effects of measurement noise on the discontinuity parameter identification are investigated by adding different levels of noise to the simulated data. The simulation results were then validated by the corresponding experiments. Both the simulation and experimental results show that (1) the one-order discontinuities can be identified accurately with the maximum errors of 6.8% and 8.7%, respectively; (2) and the high-order discontinuities can be identified with the maximum errors of 15.8% and 16.2%, respectively; and (3) the high-order model can predict the complex discontinuity much more accurately than the one-order discontinuity model.

Mode control using two electrodes on HBT-EP

NASA Astrophysics Data System (ADS)

Stewart, I. G.; Brooks, J. W.; Levesque, J. P.; Mauel, M. E.; Navratil, G. A.

2017-10-01

Understanding the effects of plasma rotation on magnetohydrodynamic (MHD) modes and tokamak plasma stability is important for performance enhancement of current magnetic confinement experiments and to future fusion devices such as ITER. In order to control plasma rotation, two molybdenum electrodes have been installed on HBT-EP toroidally separated by 144 degrees. This allows independent biasing of the two probes both spatially and temporally. When the bias probes are inserted into the edge of the plasma and a voltage is applied, the probes drive radial currents and produce plasma flow from the torque induced by the currents. If the bias probe voltage is sufficiently positive, the MHD mode rotation transitions into a state with a rapid mode rotation frequency (in excess of 25 kHz) in the direction opposite to mode rotation without bias. The transition into this reversed rotation state occurs when the torque exceeds a threshold, which can depend upon the phase of an applied n = 1 error field. We present recent studies of the two-electrode system on mode rotation, mode stability, and the toroidal symmetry of the radial current through the scrape-off-layer (SOL) during MHD activity and applied magnetic perturbations. Supported by U.S. DOE Grant DE-FG02-86ER53222.

Branch point reconstructors for discontinuous light phase functions

NASA Astrophysics Data System (ADS)

Le Bigot, Eric O.; Wild, Walter J.; Kibblewhite, Edward J.

1998-09-01

The study of phase discontinuities caused by atmospheric turbulence is a recent research topic; their study might yield significant improvements in high-quality adaptive optics systems, laser weapons and laser communication. We present in this paper an introduction to discontinuities in the light phase. We also provide a geometrical description of phase discontinuities, a study of their effect on Hartmann-Shack sensor measurements, as well as algorithms for measuring discontinuous light phases and the position of phase discontinuities.

Edge Currents and Stability in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, D M; Fenstermacher, M E; Finkenthal, D K

2004-12-01

Understanding the stability physics of the H-mode pedestal in tokamak devices requires an accurate measurement of plasma current in the pedestal region with good spatial resolution. Theoretically, the high pressure gradients achieved in the edge of H-mode plasmas should lead to generation of a significant edge current density peak through bootstrap and Pfirsh-Schl{umlt u}ter effects. This edge current is important for the achievement of second stability in the context of coupled magneto hydrodynamic (MHD) modes which are both pressure (ballooning) and current (peeling) driven. Many aspects of edge localized mode (ELM) behavior can be accounted for in terms of anmore » edge current density peak, with the identification of Type 1 ELMs as intermediate-n toroidal mode number MHD modes being a natural feature of this model. The development of a edge localized instabilities in tokamak experiments code (ELITE) based on this model allows one to efficiently calculate the stability and growth of the relevant modes for a broad range of plasma parameters and thus provides a framework for understanding the limits on pedestal height. This however requires an accurate assessment of the edge current. While estimates of j{sub edge} can be made based on specific bootstrap models, their validity may be limited in the edge (gradient scalelengths comparable to orbit size, large changes in collisionality, etc.). Therefore it is highly desirable to have an actual measurement. Such measurements have been made on the DIII-D tokamak using combined polarimetry and spectroscopy of an injected lithium beam. By analyzing one of the Zeeman-split 2S-2P lithium resonance line components, one can obtain direct information on the local magnetic field components. These values allow one to infer details of the edge current density. Because of the negligible Stark mixing of the relevant atomic levels in lithium, this method of determining j(r) is insensitive to the large local electric fields typically found in enhanced confinement (H-mode) edges, and thus avoids an ambiguity common to MSE measurements of B{sub pol}.« less

Edge Currents and Stability in DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, D M; Fenstermacher, M E; Finkenthal, D K

2005-05-05

Understanding the stability physics of the H-mode pedestal in tokamak devices requires an accurate measurement of plasma current in the pedestal region with good spatial resolution. Theoretically, the high pressure gradients achieved in the edge of H-mode plasmas should lead to generation of a significant edge current density peak through bootstrap and Pfirsh-Schlueter effects. This edge current is important for the achievement of second stability in the context of coupled magneto hydrodynamic (MHD) modes which are both pressure (ballooning) and current (peeling) driven [1]. Many aspects of edge localized mode (ELM) behavior can be accounted for in terms of anmore » edge current density peak, with the identification of Type 1 ELMs as intermediate-n toroidal mode number MHD modes being a natural feature of this model [2]. The development of a edge localized instabilities in tokamak experiments code (ELITE) based on this model allows one to efficiently calculate the stability and growth of the relevant modes for a broad range of plasma parameters [3,4] and thus provides a framework for understanding the limits on pedestal height. This however requires an accurate assessment of the edge current. While estimates of j{sub edge} can be made based on specific bootstrap models, their validity may be limited in the edge (gradient scale lengths comparable to orbit size, large changes in collisionality, etc.). Therefore it is highly desirable to have an actual measurement. Such measurements have been made on the DIII-D tokamak using combined polarimetry and spectroscopy of an injected lithium beam. [5,6]. By analyzing one of the Zeeman-split 2S-2P lithium resonance line components, one can obtain direct information on the local magnetic field components. These values allow one to infer details of the edge current density. Because of the negligible Stark mixing of the relevant atomic levels in lithium, this method of determining j(r) is insensitive to the large local electric fields typically found in enhanced confinement (H-mode) edges, and thus avoids an ambiguity common to MSE measurements of B{sub pol}.« less

Factors related to attrition from VA healthcare use: findings from the National Survey of Women Veterans.

PubMed

Hamilton, Alison B; Frayne, Susan M; Cordasco, Kristina M; Washington, Donna L

2013-07-01

While prior research characterizes women Veterans' barriers to accessing and using Veterans Health Administration (VA) care, there has been little attention to women who access VA and use services, but then discontinue use. Recent data suggest that among women Veterans, there is a 30 % attrition rate within 3 years of initial VA use. To compare individual characteristics and perceptions about VA care between women Veteran VA attriters (those who discontinue use) and non-attriters (those who continue use), and to compare recent versus remote attriters. Cross-sectional, population-based 2008-2009 national telephone survey. Six hundred twenty-six attriters and 2,065 non-attriters who responded to the National Survey of Women Veterans. Population weighted demographic, military and health characteristics; perceptions about VA healthcare; length of time since last VA use; among attriters, reasons for no longer using VA care. Fifty-four percent of the weighted VA ever user population reported that they no longer use VA. Forty-five percent of attrition was within the past ten years. Attriters had better overall health (p = 0.007), higher income (p < 0.001), and were more likely to have health insurance (p < 0.001) compared with non-attriters. Attriters had less positive perceptions of VA than non-attriters, with attriters having lower ratings of VA quality and of gender-specific features of VA care (p < 0.001). Women Veterans who discontinued VA use since 2001 did not differ from those with more remote VA use on most measures of VA perceptions. Overall, among attriters, distance to VA sites of care and having alternate insurance coverage were the most common reasons for discontinuing VA use. We found high VA attrition despite recent advances in VA care for women Veterans. Women's attrition from VA could reduce the critical mass of women Veterans in VA and affect current system-wide efforts to provide high-quality care for women Veterans. An understanding of reasons for attrition can inform organizational efforts to re-engage women who have attrited, to retain current users, and potentially to attract new VA patients.

The 520 km Discontinuity: No Longer Just the Middle Child of the Transition Zone

NASA Astrophysics Data System (ADS)

Houser, C.; Williams, Q.

2008-12-01

The 520 km discontinuity is more difficult to image and changes character laterally more relative to its siblings the 410 km and 660 km discontinuities. The 520 km discontinuity is thought to result from the phase change of β-spinel to γ-spinel, a transition which has a smaller impedance contrast than the olivine to β-spinel or the γ-spinel to perovskite and periclase transitions that are associated with the 410 km and 660 km discontinuities, respectively. In addition, there are gradual phase changes occurring in the pyroxene component of the mantle between the 410 km and 660 km discontinuity which complicate imaging and interpretation of the 520 km discontinuity. The best global coverage of discontinuity depth comes from the stacking of SS precursors, seismic phases that bounce off the discontinuities and arrive as precursors to the main SS phase. A recent study by Houser et al. (2008) contains the largest compilation of SS precursor measurements. However, since the 520 km discontinuity is not ubiquitously observed, its characteristics were not addressed. Here, we examine the geographic distribution (which is global, but not even) of high quality 520 km discontinuity measurements derived from precursors. The principal result is that the depth of the 520 km discontinuity has a higher correlation with tomographically-imaged high and low seismic velocities than either the 410 km or 660 km discontinuities. This stronger temperature sensitivity is in accord with determinations of the Clapeyron slopes of the differing transitions. Furthermore, this correlation is observed in a wide range of tectonic environments, and the prospect thus exists that the 520 km discontinuity will, where it is observed, provide a tighter bound on temperature within the transition zone than either of the other major discontinuities. Furthermore, improved constraints on the temperature distribution at depth may produce improved insight into the relative roles of thermal and compositional effects on the 660 km disctoninuity.

Statin withdrawal: clinical implications and molecular mechanisms.

PubMed

Cubeddu, Luigi X; Seamon, Matthew J

2006-09-01

Retrospective analyses of data from the Platelet Receptor Inhibition in Ischemic Syndrome Management (PRISM), the National Registry of Myocardial Infarction 4, and the Global Registry of Acute Coronary Events (GRACE) trials revealed that the benefits of 3-hydroxy-3-methylglutaryl coenzyme A reductase inhibitors (statins) on acute coronary outcomes are rapidly lost and outcomes worsened if statins are discontinued during a patient's hospitalization for an acute coronary syndrome. Withdrawal of statin therapy in the first 24 hours of hospitalization for non-ST-elevation myocardial infarction increased the hospital morbidity and mortality rate versus continued therapy (11.9% vs 5.7%, p<0.01). Data from the Treating New Targets (TNT) study, however, suggested that short-term discontinuation of statin therapy in patients with stable cardiac conditions may not substantially increase the risk of acute coronary syndromes. In patients with acute coronary syndromes who discontinue statins, the rapid increase in risk of an event may result not only from the lost benefits from the therapy, but also from rebound inhibition of vascular protective substances and activation of vascular deleterious substances. Statins inhibit cholesterol synthesis in vascular cells. By reducing levels of isoprenoid intermediates, statins increase the production of nitric oxide and downregulate angiotensin II AT(1) receptors, endothelin-1, vascular inflammatory adhesion molecules, and inflammatory cytokines. These benefits are rapidly lost and often transiently reversed when statins are acutely discontinued. Acute removal of pleiotropic effects and rebound vascular dysfunction may be more important in an acute coronary event, where inflammation promotes rupture of atherosclerotic plaques and inflammatory and prothrombosis markers are present in high concentration, than in stable chronic vascular disease. In the absence of data from randomized controlled trials, current information suggests that statin therapy should be continued, and possibly boosted, during hospitalization for an acute coronary syndrome. Because statins are discontinued during the early hospitalization of many patients, practitioners must ensure that statins are not omitted, unless contraindicated, from the treatment of patients with acute coronary syndromes.

Strategies for discontinuation of proton pump inhibitors: a systematic review.

PubMed

Haastrup, Peter; Paulsen, Maja S; Begtrup, Luise M; Hansen, Jane M; Jarbøl, Dorte E

2014-12-01

Proton pump inhibitors (PPIs) are considered to be overprescribed. Consensus on how to attempt discontinuation is, however, lacking. We therefore conducted a systematic review of clinical studies on discontinuation of PPIs. Systematic review based on clinical studies investigating discontinuation strategies and discontinuation rates for users of antisecretory medication judged eligible for withdrawal. The databases Medline, Embase and Cochrane Library were searched to December 2013 using the terms antisecretory, anti-ulcer, PPI, acid suppressant, discontinuation, step-down, step down, cessation, tapering, withdrawal and withhold. Search terms were used either singularly or in combination. Papers written in English or Scandinavian were included. Concurrent hand searching was undertaken to pursue references of references. The website ClinicalTrials.gov was searched for unpublished results and ongoing studies. A total of 371 abstracts were scrutinized to determine relevancy. The thorough search resulted in six clinical studies on strategies for discontinuation of PPIs. All discontinuation regimens used in the studies differed, and several interventions have been tested in order to decrease use of PPIs. Discontinuations were reported across all studies ranging from 14% to 64% without deteriorating symptom control. Tapering seems to be a more effective discontinuation strategy than abrupt discontinuation. Discontinuation of PPIs is feasible in a clinical setting, and a substantial number of the patients treated without a clear indication can safely reduce or discontinue treatment. Tapering seems to be the most effective way of doing this. © The Author 2014. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Reasons for discontinuation of reversible contraceptive methods by women with epilepsy.

PubMed

Mandle, Hannah B; Cahill, Kaitlyn E; Fowler, Kristen M; Hauser, W Allen; Davis, Anne R; Herzog, Andrew G

2017-05-01

To report the reasons for discontinuation of contraceptive methods by women with epilepsy (WWE). These retrospective data come from a web-based survey regarding the contraceptive practices of 1,144 WWE in the community, ages 18-47 years. We determined the frequencies of contraceptive discontinuations and the reasons for discontinuation. We compared risk ratios for rates of discontinuation among contraceptive methods and categories. We used chi-square analysis to test the independence of discontinuation reasons among the various contraceptive methods and categories and when stratified by antiepileptic drug (AED) categories. Nine hundred fifty-nine of 2,393 (40.6%) individual, reversible contraceptive methods were discontinued. One-half (51.8%) of the WWE who discontinued a method discontinued at least two methods. Hormonal contraception was discontinued most often (553/1,091, 50.7%) with a risk ratio of 1.94 (1.54-2.45, p < 0.0001) compared to intrauterine devices (IUDs), the category that was discontinued the least (57/227, 25.1%). Among all individual methods, the contraceptive patch was stopped most often (79.7%) and the progestin-IUD was stopped the least (20.1%). The top three reasons for discontinuation among all methods were reliability concerns (13.9%), menstrual problems (13.5%), and increased seizures (8.6%). There were significant differences among discontinuation rates and reasons when stratified by AED category for hormonal contraception but not for any other contraceptive category. Contraception counseling for WWE should consider the special experience profiles that are unique to this special population on systemic hormonal contraception. Wiley Periodicals, Inc. © 2017 International League Against Epilepsy.

Alternative model of space-charge-limited thermionic current flow through a plasma

DOE PAGES

Campanell, M. D.

2018-04-19

It is widely assumed that thermionic current flow through a plasma is limited by a “space-charge-limited” (SCL) cathode sheath that consumes the hot cathode's negative bias and accelerates upstream ions into the cathode. In this paper, we formulate a fundamentally different current-limited mode. In the “inverse” mode, the potentials of both electrodes are above the plasma potential, so that the plasma ions are confined. The bias is consumed by the anode sheath. There is no potential gradient in the neutral plasma region from resistivity or presheath. The inverse cathode sheath pulls some thermoelectrons back to the cathode, thereby limiting themore » circuit current. Thermoelectrons entering the zero-field plasma region that undergo collisions may also be sent back to the cathode, further attenuating the circuit current. In planar geometry, the plasma density is shown to vary linearly across the electrode gap. A continuum kinetic planar plasma diode simulation model is set up to compare the properties of current modes with classical, conventional SCL, and inverse cathode sheaths. SCL modes can exist only if charge-exchange collisions are turned off in the potential well of the virtual cathode to prevent ion trapping. With the collisions, the current-limited equilibrium must be inverse. Inverse operating modes should therefore be present or possible in many plasma devices that rely on hot cathodes. Evidence from past experiments is discussed. Finally, the inverse mode may offer opportunities to minimize sputtering and power consumption that were not previously explored due to the common assumption of SCL sheaths.« less

Alternative model of space-charge-limited thermionic current flow through a plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Campanell, M. D.

It is widely assumed that thermionic current flow through a plasma is limited by a “space-charge-limited” (SCL) cathode sheath that consumes the hot cathode's negative bias and accelerates upstream ions into the cathode. In this paper, we formulate a fundamentally different current-limited mode. In the “inverse” mode, the potentials of both electrodes are above the plasma potential, so that the plasma ions are confined. The bias is consumed by the anode sheath. There is no potential gradient in the neutral plasma region from resistivity or presheath. The inverse cathode sheath pulls some thermoelectrons back to the cathode, thereby limiting themore » circuit current. Thermoelectrons entering the zero-field plasma region that undergo collisions may also be sent back to the cathode, further attenuating the circuit current. In planar geometry, the plasma density is shown to vary linearly across the electrode gap. A continuum kinetic planar plasma diode simulation model is set up to compare the properties of current modes with classical, conventional SCL, and inverse cathode sheaths. SCL modes can exist only if charge-exchange collisions are turned off in the potential well of the virtual cathode to prevent ion trapping. With the collisions, the current-limited equilibrium must be inverse. Inverse operating modes should therefore be present or possible in many plasma devices that rely on hot cathodes. Evidence from past experiments is discussed. Finally, the inverse mode may offer opportunities to minimize sputtering and power consumption that were not previously explored due to the common assumption of SCL sheaths.« less

Studies of single-mode injection lasers and of quaternary materials. Volume 1: Single-mode constricted double-heterojunction AlGaAs diode lasers

NASA Technical Reports Server (NTRS)

Botez, D.

1982-01-01

Constricted double-heterojunction (CDH) lasers are presented as the class of single-mode nonplanar-substrate devices for which the lasing cavity is on the least resistive electrical path between the contact and the substrate. Various types of CDH structures are considered under three general topics: liquid-phase epitaxy over channeled substrates, lateral mode control, and current control in nonplanar-substrate devices. Ridge-guide CDH lasers have positive-index lateral-mode confinement and provide: single-mode CW operation to 7 mW/facet at room temperature and to 3 mW/facet at 150 C; light-current characteristics with second-harmonic distortion as low as -57 dB below the fundamental level; threshold-current temperature coefficients, as high as 375 C (pulsed) and 310 C (CW); constant external differential quantum efficiency to 100 C; and lasing operation to 170 C CW and 280 C pulsed. Semileakyguide CDH lasers have an asymmetric leaky cavity for lateral-mode confinement and provide single-mode operation to 15 to 20 mW/facet CW and to 50 mW/facet at 50% duty cycle. Modulation characteristics and preliminary reliability data are discussed.

C-Mod MHD stability analysis with LHCD

NASA Astrophysics Data System (ADS)

Ebrahimi, Fatima; Bhattacharjee, A.; Delgado, L.; Scott, S.; Wilson, J. R.; Wallace, G. M.; Shiraiwa, S.; Mumgaard, R. T.

2016-10-01

In lower hybrid current drive (LHCD) experiments on the Alcator C-Mod, sawtooth activity could be suppressed as the safety factor q on axis is raised above unity. However, in some of these experiments, after applying LHCD, the onset of MHD mode activity caused the current drive efficiency to significantly drop. Here, we study the stability of these experiments by performing MHD simulations using the NIMROD code starting with experimental EFIT equilibria. First, consistent with the LHCD experiment with no signature of MHD activity, MHD mode activity was also absent in the simulations. Second, for experiments with MHD mode activity, we find that a core n=1 reconnecting mode with dominate poloidal modes of m=2,3 is unstable. This mode is a resistive current-driven mode as its growth rate scales with a negative power of the Lundquist number in the simulations. In addition, with further enhanced reversed-shear q profile in the simulations, a core double tearing mode is found to be unstable. This work is supported by U.S. DOE cooperative agreement DE-FC02-99ER54512 using the Alcator C-Mod tokamak, a DOE Office of Science user facility.

The Influence of Motivation and Adaptation on Students' Subjective Well-Being, Meaning in Life and Academic Performance

ERIC Educational Resources Information Center

Bailey, Thomas Hamilton; Phillips, Lisa J.

2016-01-01

High rates of mental illness among students and discontinuation with university studies are regularly reported. The current study sought to explore relationships between motivation, university adaptation and indicators of mental health and well-being and academic performance of 184 first-year university students (73% female, mean age?=?19.3…

A transportable 50 kA dual mode lightning simulator

NASA Technical Reports Server (NTRS)

Salisbury, K.; Lloyd, S.; Chen, Y. G.

1991-01-01

A transportable lightning simulator was designed, built and tested, which is capable of delivering more than 50 kA to an 8 micro-H test object. The simulator was designed to be a versatile device in the lightning laboratory while meeting the requirements of MIL-STD-1757A for component E current waveforms. The system is capable of operating in either a ringing mode with a Q greater than 5 and a nominal frequency of 160 kHz, or a unipolar mode with no hardware configuration changes. The ringing mode is obtained by the LCR series circuit formed by the pulse generator and test object. The unipolar mode is obtained by closing an electrically triggered crowbar switch at peak current. The simulator exceeds the peak current requirement and rate of rise requirements for MIL-STD-1757A in both the ringing and unipolar modes. The pulse half width in the unipolar mode is in excess of 50 microsec and the action is in excess of 10(exp 5) A(exp 2)s. The design, component values, and test results are presented.

Evaluation of Atmospheric Precipitable Water from Reanalysis Products Using Homogenized Radiosonde Observations over China

NASA Astrophysics Data System (ADS)

Zhao, T.; Wang, J.; Dai, A.

2015-12-01

Many multi-decadal atmospheric reanalysis products are avialable now, but their consistencies and reliability are far from perfect. In this study, atmospheric precipitable water (PW) from the NCEP/NCAR, NCEP/DOE, MERRA, JRA-55, JRA-25, ERA-Interim, ERA-40, CFSR and 20CR reanalyses is evaluated against homogenized radiosonde observations over China during 1979-2012 (1979-2001 for ERA-40). Results suggest that the PW biases in the reanalyses are within ˜20% for most of northern and eastern China, but the reanalyses underestimate the observed PW by 20%-40% over western China, and by ˜60% over the southwestern Tibetan Plateau. The newer-generation reanalyses (e.g., JRA25, JRA55, CFSR and ERA-Interim) have smaller root-mean-square error (RMSE) than the older-generation ones (NCEP/NCAR, NCEP/DOE and ERA-40). Most of the reanalyses reproduce well the observed PW climatology and interannual variations over China. However, few reanalyses capture the observed long-term PW changes, primarily because they show spurious wet biases before about 2002. This deficiency results mainly from the discontinuities contained in reanalysis RH fields in the mid-lower troposphere due to the wet bias in older radiosonde records that are assimilated into the reanalyses. An empirical orthogonal function (EOF) analysis revealed two leading modes that represent the long-term PW changes and ENSO-related interannual variations with robust spatial patterns. The reanalysis products, especially the MERRA and JRA-25, roughly capture these EOF modes, which account for over 50% of the total variance. The results show that even during the post-1979 satellite era, discontinuities in radiosonde data can still induce large spurious long-term changes in reanalysis PW and other related fields. Thus, more efforts are needed to remove spurious changes in input data for future long-term reanlayses.

78 FR 60375 - Norfolk Southern Railway Company-Discontinuance of Service Exemption-in Claiborne County, TN, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-01

...); Docket No. AB 55 (Sub-No. 732X)] Norfolk Southern Railway Company--Discontinuance of Service Exemption... exemption under 49 CFR part 1152 Subpart F--Exempt Abandonments and Discontinuances of Service and Trackage Rights for NSR to discontinue service over, and for CSXT to discontinue trackage rights operations over...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medvedev, S. Yu., E-mail: medvedev@a5.kiam.ru; Ivanov, A. A., E-mail: aai@a5.kiam.ru; Martynov, A. A., E-mail: martynov@a5.kiam.ru

The influence of current density and pressure gradient profiles in the pedestal on the access to the regimes free from edge localized modes (ELMs) like quiescent H-mode in ITER is investigated. Using the simulator of MHD modes localized near plasma boundary based on the KINX code, calculations of the ELM stability were performed for the ITER plasma in scenarios 2 and 4 under variations of density and temperature profiles with the self-consistent bootstrap current in the pedestal. Low pressure gradient values at the separatrix, the same position of the density and temperature pedestals and high poloidal beta values facilitate reachingmore » high current density in the pedestal and a potential transition into the regime with saturated large scale kink modes. New version of the localized MHD mode simulator allows one to compute the growth rates of ideal peeling-ballooning modes with different toroidal mode numbers and to determine the stability region taking into account diamagnetic stabilization. The edge stability diagrams computations and sensitivity studies of the stability limits to the value of diamagnetic frequency show that diamagnetic stabilization of the modes with high toroidal mode numbers can help to access the quiescent H-mode even with high plasma density but only with low pressure gradient values at the separatrix. The limiting pressure at the top of the pedestal increases for higher plasma density. With flat density profile the access to the quiescent H-mode is closed even with diamagnetic stabilization taken into account, while toroidal mode numbers of the most unstable peeling-ballooning mode decrease from n = 10−40 to n = 3−20.« less

An Improved Power Quality BIBRED Converter-Based VSI-Fed BLDC Motor Drive

NASA Astrophysics Data System (ADS)

Singh, Bhim; Bist, Vashist

2014-01-01

This paper presents an IHQRR (integrated high-quality rectifier regulator) BIBRED (boost integrated buck rectifier energy storage DC-DC) converter-based VSI (voltage source inverter)-fed BLDC (brushless DC) motor drive. The speed control of BLDC motor is achieved by controlling the DC link voltage of the VSI using a single voltage sensor. This allows VSI to operate in fundamental frequency switching mode for electronic commutation of BLDC motor which reduces the switching losses due to high-frequency switching used in conventional approach of PWM (pulse width modulation)-based VSI-fed BLDC motor drive. A BIBRED converter is operated in a dual-DCM (discontinuous conduction mode) thus using a voltage follower approach for PFC (power factor correction) and DC link voltage control. The performance of the proposed drive is evaluated for improved power quality over a wide range of speed control and supply voltage variation for demonstrating the behavior of proposed drive. The power quality indices thus obtained are within the recommended limits by international PQ (power quality) standards such as IEC 61000-3-2.

Sneaker Male Squid Produce Long-lived Spermatozoa by Modulating Their Energy Metabolism.

PubMed

Hirohashi, Noritaka; Tamura-Nakano, Miwa; Nakaya, Fumio; Iida, Tomohiro; Iwata, Yoko

2016-09-09

Spermatozoa released by males should remain viable until fertilization. Hence, sperm longevity is governed by intrinsic and environmental factors in accordance with the male mating strategy. However, whether intraspecific variation of insemination modes can impact sperm longevity remains to be elucidated. In the squid Heterololigo bleekeri, male dimorphism (consort and sneaker) is linked to two discontinuous insemination modes that differ in place and time. Notably, only sneaker male spermatozoa inseminated long before egg spawning can be stored in the seminal receptacle. We found that sneaker spermatozoa exhibited greater persistence in fertilization competence and flagellar motility than consort ones because of a larger amount of flagellar glycogen. Sneaker spermatozoa also showed higher capacities in glucose uptake and lactate efflux. Lactic acidosis was considered to stabilize CO2-triggered self-clustering of sneaker spermatozoa, thus establishing hypoxia-induced metabolic changes and sperm survival. These results, together with comparative omics analyses, suggest that postcopulatory reproductive contexts define sperm longevity by modulating the inherent energy levels and metabolic pathways. © 2016 by The American Society for Biochemistry and Molecular Biology, Inc.

Comparative efficacy and safety of antibiotics used to treat acute bacterial skin and skin structure infections: Results of a network meta-analysis.

PubMed

Guest, Julian F; Esteban, Jaime; Manganelli, Anton G; Novelli, Andrea; Rizzardini, Giuliano; Serra, Miquel

2017-01-01

This NMA compared the efficacy and safety between IV antibiotics that are used in the current standard of care for managing adult patients (≥18 years of age) with ABSSSI. Comparators were chosen on the basis that both direct and indirect comparisons between the interventions of interest could be performed. Outcomes of the analysis were selected on the basis that they are frequently measured and reported in trials involving ABSSSI patients, and only published randomised control trials of any size and duration and with any blinding status were eligible for inclusion in the analysis. The NMA was performed using both a fixed-effect and random-effect model. Efficacy-related endpoints were (1) clinical treatment success and (2) microbiological success at TOC visit. Safety-related endpoints were (1) number of discontinuations due to AEs/SAEs, (2) patients experiencing AEs, (3) patients experiencing SAEs and (4) all-cause mortality. Study interventions included daptomycin, dalbavancin, linezolid and tigecycline. Vancomycin was the comparator in all studies, except in two where it was linezolid and teicoplanin. The NMA showed that irrespective of patient subgroup, the likelihood of clinical and microbiological success with dalbavancin was statistically similar to the comparators studied. No statistically significant differences were observed between dalbavancin and any of the comparators in the discontinuation rate due to AEs/SAEs. In contrast, dalbavancin was associated with a significantly lower likelihood of experiencing an AE than linezolid, a significantly lower likelihood of experiencing a SAE than vancomycin and daptomycin, and a significantly lower risk of all-cause mortality than vancomycin, linezolid and tigecycline. Dalbavancin affords a promising, new alternative IV antimicrobial agent which is as effective as traditional therapies, but with the added benefit of enabling clinicians to treat patients with ABSSSI in different organisational settings. Notwithstanding, any introduction of an effective treatment with a differential mode of administration into healthcare systems must be followed by a change in clinical practice and patient management in order to fully achieve desirable economic outcomes.