Contributions of Stress and Oxidation on the Formation of Whiskers in Pb-free Solders

DTIC Science & Technology

2016-01-29

environmental factors influencing formation of tin whiskers on electrodeposited lead free, tin coatings over copper (or copper containing) substrates is the...Oxidation on the Formation of Whiskers in Pb‐free Solders,” WP-1754 15. SUBJECT TERMS Tin Whiskers, Residual Stress, Environmental Degradation 16...showing the surface of a tin film with whisker .................... 2 Figure 2: SEM Micrograph of Tin film on Copper Substrate cross-sectioned by FIB

Effect of microstructure on the breakage of tin bronze machining chips during pulverization via jet milling

NASA Astrophysics Data System (ADS)

Afshari, Elham; Ghambari, Mohammad; Farhangi, Hasan

2016-11-01

In this study, jet milling was used to recycle tin bronze machining chips into powder. The main purpose of this study was to assess the effect of the microstructure of tin bronze machining chips on their breakage behavior. An experimental target jet mill was used to pulverize machining chips of three different tin bronze alloys containing 7wt%, 10wt%, and 12wt% of tin. Optical and electron microscopy, as well as sieve analysis, were used to follow the trend of pulverization. Each alloy exhibited a distinct rate of size reduction, particle size distribution, and fracture surface appearance. The results showed that the degree of pulverization substantially increased with increasing tin content. This behavior was attributed to the higher number of machining cracks as well as the increased volume fraction of brittle δ phase in the alloys with higher tin contents. The δ phase was observed to strongly influence the creation of machining cracks as well as the nucleation and propagation of cracks during jet milling. In addition, a direct relationship was observed between the mean δ-phase spacing and the mean size of the jet-milled product; i.e., a decrease in the δ-phase spacing resulted in smaller particles.

The C-Terminal Extension Unique to the Long Isoform of the Shelterin Component TIN2 Enhances Its Interaction with TRF2 in a Phosphorylation- and Dyskeratosis Congenita Cluster-Dependent Fashion.

PubMed

Nelson, Nya D; Dodson, Lois M; Escudero, Laura; Sukumar, Ann T; Williams, Christopher L; Mihalek, Ivana; Baldan, Alessandro; Baird, Duncan M; Bertuch, Alison A

2018-06-15

TIN2 is central to the shelterin complex, linking the telomeric proteins TRF1 and TRF2 with TPP1/POT1. Mutations in TINF2 , which encodes TIN2, that are found in dyskeratosis congenita (DC) result in very short telomeres and cluster in a region shared by the two TIN2 isoforms, TIN2S (short) and TIN2L (long). Here we show that TIN2L, but not TIN2S, is phosphorylated. TRF2 interacts more with TIN2L than TIN2S, and both the DC cluster and phosphorylation promote this enhanced interaction. The binding of TIN2L, but not TIN2S, is affected by TRF2-F120, which is also required for TRF2's interaction with end processing factors such as Apollo. Conversely, TRF1 interacts more with TIN2S than with TIN2L. A DC-associated mutation further reduces TIN2L-TRF1, but not TIN2S-TRF1, interaction. Cells overexpressing TIN2L or phosphomimetic TIN2L are permissive to telomere elongation, whereas cells overexpressing TIN2S or phosphodead TIN2L are not. Telomere lengths are unchanged in cell lines in which TIN2L expression has been eliminated by clustered regularly interspaced short palindromic repeat (CRISPR)/Cas9-mediated mutation. These results indicate that TIN2 isoforms are biochemically and functionally distinguishable and that shelterin composition could be fundamentally altered in patients with TINF2 mutations. Copyright © 2018 Nelson et al.

On-line coating of glass with tin oxide by atmospheric pressure chemical vapor deposition.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allendorf, Mark D.; Sopko, J.F.; Houf, William G.

2006-11-01

Atmospheric pressure chemical vapor deposition (APCVD) of tin oxide is a very important manufacturing technique used in the production of low-emissivity glass. It is also the primary method used to provide wear-resistant coatings on glass containers. The complexity of these systems, which involve chemical reactions in both the gas phase and on the deposition surface, as well as complex fluid dynamics, makes process optimization and design of new coating reactors a very difficult task. In 2001 the U.S. Dept. of Energy Industrial Technologies Program Glass Industry of the Future Team funded a project to address the need for more accuratemore » data concerning the tin oxide APCVD process. This report presents a case study of on-line APCVD using organometallic precursors, which are the primary reactants used in industrial coating processes. Research staff at Sandia National Laboratories in Livermore, CA, and the PPG Industries Glass Technology Center in Pittsburgh, PA collaborated to produce this work. In this report, we describe a detailed investigation of the factors controlling the growth of tin oxide films. The report begins with a discussion of the basic elements of the deposition chemistry, including gas-phase thermochemistry of tin species and mechanisms of chemical reactions involved in the decomposition of tin precursors. These results provide the basis for experimental investigations in which tin oxide growth rates were measured as a function of all major process variables. The experiments focused on growth from monobutyltintrichloride (MBTC) since this is one of the two primary precursors used industrially. There are almost no reliable growth-rate data available for this precursor. Robust models describing the growth rate as a function of these variables are derived from modeling of these data. Finally, the results are used to conduct computational fluid dynamic simulations of both pilot- and full-scale coating reactors. As a result, general conclusions are reached concerning the factors affecting the growth rate in on-line APCVD reactors. In addition, a substantial body of data was generated that can be used to model many different industrial tin oxide coating processes. These data include the most extensive compilation of thermochemistry for gas-phase tin-containing species as well as kinetic expressions describing tin oxide growth rates over a wide range of temperatures, pressures, and reactant concentrations.« less

Positron annihilation and X-ray diffraction studies on tin oxide thin films

NASA Astrophysics Data System (ADS)

Prabakar, K.; Abhaya, S.; Krishnan, R.; Kalavathi, S.; Dash, S.; Jayapandian, J.; Amarendra, G.

2009-04-01

Positron annihilation spectroscopy along with glancing incidence X-ray diffraction have been used to investigate tin oxide thin films grown on Si by pulsed laser deposition. The films were prepared at room temperature and at 670 K under oxygen partial pressure. As-grown samples are amorphous and are found to contain large concentration of open volume sites (vacancy defects). Post-deposition annealing of as-grown samples at 970 K is found to drastically reduce the number of open volume sites and the film becomes crystalline. However, film grown under elevated temperature and under partial pressure of oxygen is found to exhibit a lower S-parameter, indicating lower defect concentration. Based on the analysis of experimental positron annihilation results, the defect-sensitive S-parameter and the overlayer thickness of tin oxide thin films are deduced. S- W correlation plots exhibit distinct positron trapping defect states in three samples.

Synthesis and characterization of 8-hydroxyquinoline complexes of tin(IV) and their application in organic light emitting diode.

PubMed

Fazaeli, Yousef; Amini, Mostafa M; Najafi, Ezzatollah; Mohajerani, Ezeddin; Janghouri, Mohammad; Jalilian, Amirreza; Ng, Seik Weng

2012-09-01

A series of 8-hydroxyquinoline complexes of tin, Q(2)SnCl(2) (Q = 2-methyl-8-hydroxyquinoline, 8-hydroxyquinoline, 5,7-dibromo-8-hydroxyquinoline, 5-chloro-8-hydroxyquinoline, 5,7-dichloro-8-hydroxyquinoline and 5-nitro-8-hydroxyquinoline) were prepared by reacting stannous dichloride with 8-hydroxyquinoline and its derivatives. All complexes were characterized by elemental analysis, mass spectrometry and infrared, UV-vis and (1)H NMR spectroscopes. Furthermore, the molecular structure of a representative complex, dichlorido-bis(5-nitro-quinolin-8-olato-2N,O)tin(IV), was determined by single-crystal X-ray diffraction. The photoluminescence (PL) properties of all prepared compounds and electroluminescence (EL) property of a selected complex (Q = 5-chloro-8-hydroxyquinoline) were investigated. The results showed that the emission wavelength can be tuned by electron donating or withdrawing group substituent on 8-hydroxyquinoline. Application of prepared complexes in fabrication of an OLED has been demonstrated.

Fundamental Factors Impacting the Stability of Phosphonate-Derivatized Ruthenium Polypyridyl Sensitizers Adsorbed on Metal Oxide Surfaces.

PubMed

Raber, McKenzie; Brady, Matthew David; Troian-Gautier, Ludovic; Dickenson, John; Marquard, Seth L; Hyde, Jacob; Lopez, Santiago; Meyer, Gerald J; Meyer, Thomas J; Harrison, Daniel P

2018-06-08

A series of 18 ruthenium(II) polypyridyl complexes were synthesized and evaluated under electrochemically oxidative conditions, which generates the Ru(III) oxidation state and mimics the harsh conditions experienced during the kinetically-limited regime that can occur in dye-sensitized solar cells (DSSCs) and dye-sensitized photoelectrosynthesis cells (DSPECs), to further develop fundamental insights into the factors governing molecular sensitizer surface stability in aqueous 0.1 M HClO4 (aq). Both desorption and oxidatively induced ligand substitution were observed on planar fluorine doped tin oxide, FTO, electrodes, with a dependence on the E1/2 Ru(III/II) redox potential dictating the comparative ratios of the processes. Complexes such as RuP4OMe (E1/2 = 0.91 vs Ag/AgCl) displayed virtually only desorption, while complexes such as RuPbpz (E1/2 > 1.62 V vs Ag/AgCl) displayed only chemical decomposition. Comparing isomers of 4,4'- and 5,5-disubstituted-2,2'-bipyridine ancillary polypyridyl ligands, a dramatic increase in the rate of desorption of the Ru(III) complexes was observed for the 5,5'-ligands. Nanoscopic indium doped tin oxide thin films, nanoITO, were also sensitized and analyzed with cyclic voltammetry, UV-Vis absorption spectroscopy, and XPS, allowing for further distinction of desorption versus ligand substitution processes. Desorption loss to bulk solution associated with the planar surface of FTO is essentially non-existent on nanoITO, where both desorption and ligand substitution are shut down with RuP4OMe. These results revealed that minimizing time spent in the oxidized form, incorporating electron donating groups, maximizing hydrophobicity, and minimizing molecular bulk near the adsorbed ligand are critical to optimizing the performance of ruthenium(II) polypyridyl complexes in dye-sensitized solar cell devices.

Precipitation Behaviors of TiN Inclusion in GCr15 Bearing Steel Billet

NASA Astrophysics Data System (ADS)

Tian, Qianren; Wang, Guocheng; Zhao, Yang; Li, Jing; Wang, Qi

2018-06-01

There are many types of non-metallic TiN-based inclusions observed in GCr15 bearing steel, including single-particle TiN, multi-particle polymerized TiN, and complex inclusions like TiN-MnS, TiN-MgO-MgAl2O4 (TiN-MgO-MA), and TiN-MgAl2O4-MnS (TiN-MA-MnS). Thermodynamic calculations suggest that single-particle TiN precipitates dominate the mushy zone of GCr15 bearing steel. Kinetic calculations regarding TiN growth suggest that the final size of the single-particle TiN ranges between 1 and 6 μm in the initial concentration range of [pct Ti] = 0.0060 to 0.0079 and [pct N] = 0.0049 to 0.0070, at 1620 to 1640 K and a local cooling rate of 0.5 to 10 K/s. The multi-particle polymerized TiN are formed by single TiN particles in three stages: single-particle TiN inclusions approach each other drawn by the cavity bridge force (CBF), local active angles consolidate, and neck region sintering occurs. Based on the thermodynamic calculations of TiN, MnS, and MgO precipitation, the formation behaviors of complex inclusions of TiN-MnS, TiN-MgO-MA, and TiN-MA-MnS were investigated.

Quadtree of TIN: a new algorithm of dynamic LOD

NASA Astrophysics Data System (ADS)

Zhang, Junfeng; Fei, Lifan; Chen, Zhen

2009-10-01

Currently, Real-time visualization of large-scale digital elevation model mainly employs the regular structure of GRID based on quadtree and triangle simplification methods based on irregular triangulated network (TIN). TIN is a refined means to express the terrain surface in the computer science, compared with GRID. However, the data structure of TIN model is complex, and is difficult to realize view-dependence representation of level of detail (LOD) quickly. GRID is a simple method to realize the LOD of terrain, but contains more triangle count. A new algorithm, which takes full advantage of the two methods' merit, is presented in this paper. This algorithm combines TIN with quadtree structure to realize the view-dependence LOD controlling over the irregular sampling point sets, and holds the details through the distance of viewpoint and the geometric error of terrain. Experiments indicate that this approach can generate an efficient quadtree triangulation hierarchy over any irregular sampling point sets and achieve dynamic and visual multi-resolution performance of large-scale terrain at real-time.

Low-debris, efficient laser-produced plasma extreme ultraviolet source by use of a regenerative liquid microjet target containing tin dioxide (SnO2) nanoparticles

NASA Astrophysics Data System (ADS)

Higashiguchi, Takeshi; Dojyo, Naoto; Hamada, Masaya; Sasaki, Wataru; Kubodera, Shoichi

2006-05-01

We demonstrated a low-debris, efficient laser-produced plasma extreme ultraviolet (EUV) source by use of a regenerative liquid microjet target containing tin-dioxide (SnO2) nanoparticles. By using a low SnO2 concentration (6%) solution and dual laser pulses for the plasma control, we observed the EUV conversion efficiency of 1.2% with undetectable debris.

Bonding in Some Zintl Phases: A Study by Tin-119 Mössbauer Spectroscopy

NASA Astrophysics Data System (ADS)

Asbrand, M.; Berry, F. J.; Eisenmann, B.; Kniep, R.; Smart, L. E.; Thied, R. C.

1995-09-01

The 119Sn Mössbauer parameters for a range of Zintl phase compounds are reported. The compounds containing tetrahedrally coordinated tin of composition M5SnX3 (M = Na, K; X = P, As, Sb) have chemical isomer shifts close to that of grey-tin and can be considered to be covalently bonded species. The layer structures of composition KSnX (X = As, Sb) and double-layer compounds M Sn2X2 (M = Na, Sr; X = As, Sb) have tin in a distorted octahedral environment. The chemical isomer shifts are closer to that of white-tin and can be interpreted in terms of metallic bonding.

Mother-Child Conversations about Pictures and Objects: Referring to Categories and Individuals

ERIC Educational Resources Information Center

Gelman, Susan A.; Chesnick, Robert J.; Waxman, Sandra R.

2005-01-01

The distinction between individuals (e.g., Rin-Tin-Tin) and categories (e.g., dogs) is fundamental in human thought. Two studies examined factors that influence when 2- to 3-year-old children and adults focus on individuals versus categories. Mother-child dyads were presented with pictures and toys (e.g., a picture of a boat or a toy boat).…

Selective etching of TiN over TaN and vice versa in chlorine-containing plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shin, Hyungjoo; Zhu Weiye; Liu Lei

2013-05-15

Selectivity of etching between physical vapor-deposited TiN and TaN was studied in chlorine-containing plasmas, under isotropic etching conditions. Etching rates for blanket films were measured in-situ using optical emission of the N{sub 2} (C{sup 3}{Pi}{sub u}{yields}B{sup 3}{Pi}{sub g}) bandhead at 337 nm to determine the etching time, and transmission electron microscopy to determine the starting film thickness. The etching selectivity in Cl{sub 2}/He or HCl/He plasmas was poor (<2:1). There was a window of very high selectivity of etching TiN over TaN by adding small amounts (<1%) of O{sub 2} in the Cl{sub 2}/He plasma. Reverse selectivity (10:1 of TaNmore » etching over TiN) was observed when adding small amounts of O{sub 2} to the HCl/He plasma. Results are explained on the basis of the volatility of plausible reaction products.« less

Synthesis and characterization of tin(II) complexes of fluorinated Schiff bases derived from amino acids.

PubMed

Singh, Har Lal

2010-07-01

New tin(II) complexes of general formula Sn(L)(2) (L=monoanion of 3-methyl-4-fluoro-acetophenone phenylalanine L(1)H, 3-methyl-4-fluoro-acetophenone alanine L(2)H, 3-methyl-4-fluoro acetophenone tryptophan L(3)H, 3-methyl-4-fluoro-acetophenone valine L(4)H, 3-methyl-4-fluoro-acetophenone isoleucine L(5)H and 3-methyl-4-fluoro-acetophenone glycine L(6)H) have been prepared. It is characterized by elemental analyses, molar conductance measurements and molecular weight determinations. Bonding of these complexes is discussed in terms of their UV-visible, infrared, and nuclear magnetic resonance ((1)H, (13)C, (19)F and (119)Sn NMR) spectral studies. The ligands act as bidentate towards metal ions, via the azomethine nitrogen and deprotonated oxygen of the respective amino acid. Elemental analyses and NMR spectral data of the ligands with their tin(II) complexes agree with their proposed square pyramidal structures. A few representative ligands and their tin complexes have been screened for their antibacterial activities and found to be quite active in this respect. Copyright 2010 Elsevier B.V. All rights reserved.

Suppression of suprathermal ions from a colloidal microjet target containing SnO2 nanoparticles by using double laser pulses

NASA Astrophysics Data System (ADS)

Higashiguchi, Takeshi; Kaku, Masanori; Katto, Masahito; Kubodera, Shoichi

2007-10-01

We have demonstrated suppression of suprathermal ions from a colloidal microjet target plasma containing tin-dioxide (SnO2) nanoparticles irradiated by double laser pulses. We observed a significant decrease of the tin and oxygen ion signals in the charged-state-separated energy spectra when double laser pulses were irradiated. The peak energy of the singly ionized tin ions decreased from 9to3keV when a preplasma was produced. The decrease in the ion energy, considered as debris suppression, is attributed to the interaction between an expanding low-density preplasma and a main laser pulse.

Studies on the electrodeposition of tin from acidic chloride-gluconate solutions

NASA Astrophysics Data System (ADS)

Rudnik, Ewa; Włoch, Grzegorz

2013-01-01

Electrodeposition of tin from acidic chloride-gluconate baths was investigated. Equilibrium distribution of tin(II) species showed domination of Sn(II)-gluconate complexes, but for Sn2+ concentrations 50 mM or higher increased percentage of Sn(II)-chloride complexes was found. Cyclic voltammetry, anodic stripping analysis and potentiostatic measurements indicated that rate of the cathodic process is determined by the release of metal cations from gluconate complexes in diluted bath (5 mM), but for more concentrated solutions reduction of Sn(II) ions run under diffusion control. Studies of anodic response showed that it depends on the Sn(II)/Glu ratio in the bath and deposition potential due to development of different planes of metal crystal. Average effective diffusion coefficients of metal species were determined. Morphology and structure tin deposits were also presented.

Molten tin reprocessing of spent nuclear fuel elements

DOEpatents

Heckman, Richard A.

1983-01-01

A method and apparatus for reprocessing spent nuclear fuel is described. Within a containment vessel, a solid plug of tin and nitride precipitates supports a circulating bath of liquid tin therein. Spent nuclear fuel is immersed in the liquid tin under an atmosphere of nitrogen, resulting in the formation of nitride precipitates. The layer of liquid tin and nitride precipitates which interfaces the plug is solidified and integrated with the plug. Part of the plug is melted, removing nitride precipitates from the containment vessel, while a portion of the plug remains solidified to support the liquid tin and nitride precipitates remaining in the containment vessel. The process is practiced numerous times until substantially all of the precipitated nitrides are removed from the containment vessel.

Molten tin reprocessing of spent nuclear fuel elements. [Patent application; continuous process

DOEpatents

Heckman, R.A.

1980-12-19

A method and apparatus for reprocessing spent nuclear fuel is described. Within a containment vessel, a solid plug of tin and nitride precipitates supports a circulating bath of liquid tin therein. Spent nuclear fuel is immersed in the liquid tin under an atmosphere of nitrogen, resulting in the formation of nitride precipitates. The layer of liquid tin and nitride precipitates which interfaces the plug is solidified and integrated with the plug. Part of the plug is melted, removing nitride precipitates from the containment vessel, while a portion of the plug remains solidified to support te liquid tin and nitride precipitates remaining in the containment vessel. The process is practiced numerous times until substantially all of the precipitated nitrides are removed from the containment vessel.

The Southeast Asian Tin Belt

NASA Astrophysics Data System (ADS)

Schwartz, M. O.; Rajah, S. S.; Askury, A. K.; Putthapiban, P.; Djaswadi, S.

1995-07-01

The Southeast Asian Tin Belt is a north-south elongate zone 2800 km long and 400 km wide, extending from Burma (Myanmar) and Thailand to Peninsular Malaysia and the Indonesian Tin Islands. Altogether 9.6 million tonnes of tin, equivalent to 54% of the world's tin production is derived from this region. Most of the granitoids in the region can be grouped geographically into elongate provinces or belts, based on petrographic and geochronological features. - The Main Range Granitoid Province in western Peninsular Malaysia, southern Peninsular Thailand and central Thailand is almost entirely made up of biotite granite (184-230 Ma). Tin deposits associated with these granites contributed 55% of the historic tin production of Southeast Asia. - The Northern Granitoid Province in northern Thailand (0.1% of tin production) also has dominant biotite granite (200-269 Ma) but it is distinguished by abundant post-intrusion deformation. - The Eastern Granitoid Province extends from eastern Peninsular Malaysia to eastern Thailand. The Malaysian part is subdivided into the East Coast Belt (220-263 Ma), Boundary Range Belt (197-257 Ma) and Central Belt (79-219 Ma). The granitoids cover a wide compositional range from biotite granite to hornblende-biotite granite/granodiorite and diorite-gabbro. Tin deposits are associated with biotite granite in the East Coast Belt (3% of tin production). The granitoids in the other areas of the Eastern Granitoid Province are barren. - The Western Granitoid Province (22-149 Ma) in northern Peninsular Thailand, western Thailand and Burma has biotite granite and hornblende-biotite granite/granodiorite. Tin deposits are associated with biotite granite, which probably is the dominant phase (14% of tin production). The granitoids of the Indonesian Tin Islands (193-251 Ma) do not permit grouping into geographically distinct units. Main Range-type and Eastern Province-type plutons occur next to each other. Most of the tin deposits are associated with Main Range-type plutons (28% of tin production). Tin-mineralized plutons are characterized by high concentrations of SiO 2, K 2O, Rb, Sn, Th and U, whereas the concentrations of Fe 2O 3, MgO, CaO, Na 2O, Ba and Sr as well as the Fe2O3/FeO ratios are low. Tin-mineralized plutons are also distinguished by high initial 87Sr/86Sr ratios low magnetic susceptibilities.

Effect of Tin, Copper and Boron on the Hot Ductility of 20CrMnTi Steel between 650 °C and 1100 °C

NASA Astrophysics Data System (ADS)

Peng, Hong-bing; Chen, Wei-qing; Chen, Lie; Guo, Dong

2015-02-01

The hot ductility of 20CrMnTi steel with x% tin, y% copper and z ppm boron (x = 0, 0.02; y = 0, 0.2; z = 0, 60) was investigated. The results show that tin and copper in 20CrMnTi steel are detrimental to its hot ductility while adding boron can eliminate the adverse effect and enhance hot ductility greatly. Tin is found to segregate to the boundaries tested by EPMA in 20CrMnTi steel containing tin and copper and tin-segregation is suppressed by adding boron, moreover, copper was found not to segregate to boundaries, however, fine copper sulfide was found from carbon extraction replicas using TEM. The adverse effect of tin and copper on the hot ductility was due mainly to tin segregation and fine copper sulfide in the steel. The proeutectoid ferrite film precipitating along the austenite grain boundary causes the ductility trough of the three examined steels. Tin and copper in 20CrMnTi steel can retard the occurrence of dynamic recrystallization (DRX) while boron-addition can compensate for that change. The beneficial effect of boron on 20CrMnTi steel containing tin and copper might be ascribed to the fact that boron segregates to grain boundaries, accelerates onset of DRX, retards austenite/ferrite transformation and promotes intragranular nucleation of ferrite.

Electrodeposition of nanostructured Sn-Zn coatings

NASA Astrophysics Data System (ADS)

Salhi, Y.; Cherrouf, S.; Cherkaoui, M.; Abdelouahdi, K.

2016-03-01

The electrodeposition of Sn-Zn coating at ambient temperature was investigated. The bath consists of metal salts SnCl2·2H2O and ZnSO4·7H2O and sodium citrate (NaC6H5Na3O7·2H2O) as complexing agent. To prevent precipitation, the pH is fixed at 5. Reducing tin and zinc through Sncit2- and ZnHcit- complex respectively is confirmed by the presence of two cathodic peaks on the voltammogram. The kinetic of tin (II) reduction process is limited by the SnCit2- dissociation. The SEM and TEM observations have showed that the coating consists of a uniform Sn-Zn layer composed of fine grains on which tin aggregates grow up. XRD revealed peaks corresponding to the hexagonal Zn phase and the tetragonal β-Sn phase.

Palladium-tin catalysts for the direct synthesis of H 2O 2 with high selectivity

DOE PAGES

Freakley, Simon J.; He, Qian; Harrhy, Jonathan H.; ...

2016-02-25

The direct synthesis of hydrogen peroxide (H 2O 2 ) from H 2 and O 2 represents a potentially atom-efficient alternative to the current industrial indirect process. We show that the addition of tin to palladium catalysts coupled with an appropriate heat treatment cycle switches off the sequential hydrogenation and decomposition reactions, enabling selectivities of >95% toward H 2O 2 . This effect arises from a tin oxide surface layer that encapsulates small Pd-rich particles while leaving larger Pd-Sn alloy particles exposed. In conclusion, we show that this effect is a general feature for oxide-supported Pd catalysts containing an appropriatemore » second metal oxide component, and we set out the design principles for producing high-selectivity Pd-based catalysts for direct H 2O 2 production that do not contain gold.« less

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2012 CFR

2012-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2010 CFR

2010-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2014 CFR

2014-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2011 CFR

2011-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...

46 CFR 160.026-3 - Container.

Code of Federal Regulations, 2013 CFR

2013-10-01

... on the outside. The can shall be made of 1.25-pound coating coke tin-plate throughout, with not less.... The interior of the container shall be uncoated, except for the tin-plating required by paragraph (a) of this section. In addition to the tin-plating, the exterior surfaces of the container, including...

Reductive precipitation of metals photosensitized by tin and antimony porphyrins

DOEpatents

Shelnutt, John A.; Gong, Weiliang; Abdelouas, Abdesselam; Lutze, Werner

2003-09-30

A method for reducing metals using a tin or antimony porphyrin by forming an aqueous solution of a tin or antimony porphyrin, an electron donor, such as ethylenediaminetetraaceticacid, triethylamine, triethanolamine, and sodium nitrite, and at least one metal compound selected from a uranium-containing compound, a mercury-containing compound, a copper-containing compound, a lead-containing compound, a gold-containing compound, a silver-containing compound, and a platinum-containing compound through irradiating the aqueous solution with light.

Novel Organotin(IV) Schiff Base Complexes with Histidine Derivatives: Synthesis, Characterization, and Biological Activity

PubMed Central

Garza-Ortiz, Ariadna; Camacho-Camacho, Carlos; Sainz-Espuñes, Teresita; Rojas-Oviedo, Irma; Gutiérrez-Lucas, Luis Raúl; Gutierrez Carrillo, Atilano; Vera Ramirez, Marco A.

2013-01-01

Five novel tin Schiff base complexes with histidine analogues (derived from the condensation reaction between L-histidine and 3,5-di-tert-butyl-2-hydroxybenzaldehyde) have been synthesized and characterized. Characterization has been completed by IR and high-resolution mass spectroscopy, 1D and 2D solution NMR (1H, 13C  and 119Sn), as well as solid state 119Sn NMR. The spectroscopic evidence shows two types of structures: a trigonal bipyramidal stereochemistry with the tin atom coordinated to five donating atoms (two oxygen atoms, one nitrogen atom, and two carbon atoms belonging to the alkyl moieties), where one molecule of ligand is coordinated in a three dentate fashion. The second structure is spectroscopically described as a tetrahedral tin complex with four donating atoms (one oxygen atom coordinated to the metal and three carbon atoms belonging to the alkyl or aryl substituents), with one molecule of ligand attached. The antimicrobial activity of the tin compounds has been tested against the growth of bacteria in vitro to assess their bactericidal properties. While pentacoordinated compounds 1, 2, and 3 are described as moderate effective to noneffective drugs against both Gram-positive and Gram-negative bacteria, tetracoordinated tin(IV) compounds 4 and 5 are considered as moderate effective and most effective compounds, respectively, against the methicillin-resistant Staphylococcus aureus strains (Gram-positive). PMID:23864839

Optimisation of spray-drying process variables for dry powder inhalation (DPI) formulations of corticosteroid/cyclodextrin inclusion complexes.

PubMed

Cabral-Marques, Helena; Almeida, Rita

2009-09-01

This study aims to develop and characterise a beclomethasone diproprionate:gamma-cyclodextrin (BDP:gamma-CYD) complex and to optimise the variables on the spray-drying process, in order to obtain a powder with the most suitable characteristics for lung delivery. The spray-dried powder--in a mass ratio of 2:5 (BDP:gamma-CYD)--was physically mixed with three carriers of different particle sizes and in different ratios. Particle-size distribution, shape and morphology, moisture content, and uniformity in BDP content of formulations were studied. In vitro aerolisation behaviour of the formulations was evaluated using the Rotahaler, and the performance was characterised based on the uniformity of emitted dose and aerodynamic particle-size distribution (respirable fraction (RF), as a percentage of nominal dose (RFN) and emitted dose (RFE)). The most suitable conditions for the preparation of BDP:gamma-CYD complexes were obtained with the solution flow of 5 ml/min, T(in) of 70 degrees C and T(out) of 50 degrees C. Statistically significant differences in the aerodynamic performances were obtained for formulations containing BDP:gamma-CYD complexes prepared using different solution flows and different T(in) (p<0.05). RFN and RFE vary in direct proportion with T(in), while an inverse relationship was observed for the solution flow. A direct correlation between the RFE and the T(out) was identified. Performance of the formulations was compared with an established commercial product (Beclotaide Rotacaps 100 microg) with improved performance of RF: formulations with respitose carrier attained RFN and RFE twofold greater, and formulations based on 63-90 microm fraction lactose and trehalose achieved a threefold improvement; also, all formulations showed that the percentage of dose of BDP deposited in the "oropharynx" compartment was reduced to half.

Inductively coupled plasma atomic emission spectrometric determination of tin in canned food.

PubMed

Sumitani, H; Suekane, S; Nakatani, A; Tatsuka, K

1993-01-01

Various canned foods were digested sequentially with HNO3 and HCl, diluted to 100 mL, and filtered, and then tin was determined by inductively coupled plasma atomic emission spectrometry (ICP/AES). Samples of canned Satsuma mandarin, peach, apricot, pineapple, apple juice, mushroom, asparagus, evaporated milk, short-necked clam, spinach, whole tomato, meat, and salmon were evaluated. Sample preparations did not require time-consuming dilutions, because ICP/AES has wide dynamic range. The standard addition method was used to determine tin concentration. Accuracy of the method was tested by analyzing analytical standards containing tin at 2 levels (50 and 250 micrograms/g). The amounts of tin found for the 50 and 250 micrograms/g levels were 50.5 and 256 micrograms/g, respectively, and the repeatability coefficients of variation were 4.0 and 3.8%, respectively. Recovery of tin from 13 canned foods spiked at 2 levels (50 and 250 micrograms/g) ranged from 93.9 to 109.4%, with a mean of 99.2%. The quantitation limit for tin standard solution was about 0.5 microgram/g.

Mössbauer and X-ray Diffraction Investigations of Sn-containing Binary and Ternary Electrodeposited Alloys from a Gluconate Bath

NASA Astrophysics Data System (ADS)

Kuzmann, E.; Stichleutner, S.; Doyle, O.; Chisholm, C. U.; El-Sharif, M.; Homonnay, Z.; Vértes, A.

2005-04-01

Constant current technique was applied to electrodeposit tin-containing coatings such as tin-cobalt (Sn-Co), tin-iron (Sn-Fe) and a novel tin-cobalt-iron (Sn-Co-Fe) from a gluconate bath. The effect of plating parameters (current density, deposition time at an electrolyte temperature of 60°C and pH=7.0) on phase composition, crystal structure and magnetic anisotropy of alloy deposits has been investigated mainly by 57Fe CEMS, 119Sn CEMS and transmission Mössbauer Spectroscopy as well as XRD. 57Fe and 119Sn CEM spectra and XRD reflect that the dominant phases of the deposits are orthorhombic Co3Sn2, tetragonal FeSn2 or amorphous Fe-Sn and amorphous Sn-Co-Fe in Sn-Co, Sn-Fe and Sn-Co-Fe coatings, respectively. Furthermore, the relative area of the 2nd and 5th lines of the sextets representing the magnetic iron containing phases decreases continuously with increasing current density in all Fe-containing deposits. At the same time, no essential change in the magnetic anisotropy can be found with the plating time. 119Sn spectra reveal the presence of small amount of β-Sn besides the main phases in Sn-Fe and in the Sn-Co coatings. Magnetically split 119Sn spectra reflecting transferred hyperfine field were observed in the case of Co-Sn-Fe coatings.

The behaviour of boron in a peraluminous granite-pegmatite system and associated hydrothermal solutions: a melt and fluid-inclusion study

NASA Astrophysics Data System (ADS)

Thomas, Rainer; Förster, Hans-Jürgen; Heinrich, Wilhelm

2002-09-01

Detailed analyses of melt and fluid inclusions combined with an electron-microprobe survey of boron-bearing minerals reveal the evolution of boron in a highly evolved peraluminous granite-pegmatite complex and the associated high- and medium-temperature ore-forming hydrothermal fluids (Ehrenfriedersdorf, Erzgebirge, Germany). Melt inclusions in granite represent embryonic pegmatite-forming melts containing about 10 wt% H2O and 1.8 wt% B2O3. These melts are also enriched in F, P, and other incompatible elements such as Be, Sn, Rb, and Cs. Ongoing differentiation and volatile enrichment drove the system into a solvus, where two pegmatite-forming melts coexisted. The critical point is at about 712 °C, 100 MPa, 20 wt% H2O and 4.1 wt% B2O3. Cooling and concomitant fractional crystallisation from 700 to 500 °C induced development of two conjugate melts, an H2O-poor (A-melt) and an H2O-rich melt (B-melt) along the opening solvus. Boron is a major element in both melts and is preferentially partitioned into the H2O-rich melt. Temperature-dependent distribution coefficients $ D{boron}{{B - melt/A - melt}} $ are 1.3 at 650 °C, 1.5 at 600 °C, and 1.8 at 500 °C. In both melts, boron concentrations decreased during cooling because of exsolution of a boron-rich hypersaline brine throughout the pegmatitic stage. Boromuscovite containing up to 8.5 wt% was another sink for boron at this stage. The end of the melt-dominated pegmatitic stage was attained at a solidus temperature of around 490 °C. Fluid inclusions of the hydrothermal stage reveal trapping temperatures of 480 to 370 °C, along with varying densities and highly variable B2O3 contents ranging from 0.20 to 2.94 wt%. A boiling system evolved, indicating a complex interplay between closed- and open-system behaviour. Pressure switched from lithostatic to hydrostatic and back, generating hydrothermal convection cells where meteoric waters were introduced and mixed with magmatic fluids. Boron-rich solutions originated from magmatic fluids, whereas boron-depleted fluids were mainly of meteoric origin. This highlights the potential of boron for discriminating fluids of different origin. Tin is continuously enriched during the evolution because tin and boron are cross-linked by formation of boron-, fluorine- and tin-fluorine-bearing complexes and is finally deposited within quartz-cassiterite veins during the transition from closed- to open-system behaviour. Boron does not only trace the complex evolution of the Ehrenfriedersdorf complex but exerts, together with H2O, F and P, an important control on the physical and chemical properties of pegmatite-forming melts, and particularly on the formation of a two-melt solvus at low pressure. We discuss this with respect to experimental results on H2O solubility and the critical behaviour of the haplogranite-water system which contained variable concentrations of volatiles.

The behaviour of boron in a peraluminous granite-pegmatite system and associated hydrothermal solutions: a melt and fluid-inclusion study

NASA Astrophysics Data System (ADS)

Thomas, Rainer; Förster, Hans-Jürgen; Heinrich, Wilhelm

Detailed analyses of melt and fluid inclusions combined with an electron-microprobe survey of boron-bearing minerals reveal the evolution of boron in a highly evolved peraluminous granite-pegmatite complex and the associated high- and medium-temperature ore-forming hydrothermal fluids (Ehrenfriedersdorf, Erzgebirge, Germany). Melt inclusions in granite represent embryonic pegmatite-forming melts containing about 10 wt% H2O and 1.8 wt% B2O3. These melts are also enriched in F, P, and other incompatible elements such as Be, Sn, Rb, and Cs. Ongoing differentiation and volatile enrichment drove the system into a solvus, where two pegmatite-forming melts coexisted. The critical point is at about 712 °C, 100 MPa, 20 wt% H2O and 4.1 wt% B2O3. Cooling and concomitant fractional crystallisation from 700 to 500 °C induced development of two conjugate melts, an H2O-poor (A-melt) and an H2O-rich melt (B-melt) along the opening solvus. Boron is a major element in both melts and is preferentially partitioned into the H2O-rich melt. Temperature-dependent distribution coefficients $ D{boron}{{B - melt/A - melt}} $ are 1.3 at 650 °C, 1.5 at 600 °C, and 1.8 at 500 °C. In both melts, boron concentrations decreased during cooling because of exsolution of a boron-rich hypersaline brine throughout the pegmatitic stage. Boromuscovite containing up to 8.5 wt% was another sink for boron at this stage. The end of the melt-dominated pegmatitic stage was attained at a solidus temperature of around 490 °C. Fluid inclusions of the hydrothermal stage reveal trapping temperatures of 480 to 370 °C, along with varying densities and highly variable B2O3 contents ranging from 0.20 to 2.94 wt%. A boiling system evolved, indicating a complex interplay between closed- and open-system behaviour. Pressure switched from lithostatic to hydrostatic and back, generating hydrothermal convection cells where meteoric waters were introduced and mixed with magmatic fluids. Boron-rich solutions originated from magmatic fluids, whereas boron-depleted fluids were mainly of meteoric origin. This highlights the potential of boron for discriminating fluids of different origin. Tin is continuously enriched during the evolution because tin and boron are cross-linked by formation of boron-, fluorine- and tin-fluorine-bearing complexes and is finally deposited within quartz-cassiterite veins during the transition from closed- to open-system behaviour. Boron does not only trace the complex evolution of the Ehrenfriedersdorf complex but exerts, together with H2O, F and P, an important control on the physical and chemical properties of pegmatite-forming melts, and particularly on the formation of a two-melt solvus at low pressure. We discuss this with respect to experimental results on H2O solubility and the critical behaviour of the haplogranite-water system which contained variable concentrations of volatiles.

Mössbauer and NMR study of novel Tin(IV)-lactames

NASA Astrophysics Data System (ADS)

Kuzmann, Erno; Szalay, Roland; Homonnay, Zoltan; Nagy, Sandor

2012-03-01

N-tributylstannylated 2-pyrrolidinone was reacted with tributyltin triflate in different molar ratios and the complex formation monitored using 1H-NMR, 13C-NMR and 119Sn Mössbauer spectroscopy. Comparing the carbon NMR and tin Mössbauer results, a reaction scheme is suggested for the complexation which assumes the formation of a simultaneously O- and N-tributylstannylated pyrrolidinone cation. The formation of the only O-stannylated pyrrolidinone is also assumed to account for the non-constant Mössbauer parameters of the two tin environments in the distannylated pyrrolidinone cation when the ratio of tributyltin triflate is increased in the reaction.

METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

DOEpatents

Lemon, L.C.

1960-05-24

Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

Petrogenesis of Cretaceous volcanic-intrusive complex from the giant Yanbei tin deposit, South China: Implication for multiple magma sources, tin mineralization, and geodynamic setting

NASA Astrophysics Data System (ADS)

Li, Qian; Zhao, Kui-Dong; Lai, Pan-Chen; Jiang, Shao-Yong; Chen, Wei

2018-01-01

The giant Yanbei tin ore deposit is the largest porphyry-type tin deposit in South China. The orebodies are hosted by the granite porphyry in the central part of the Yanbei volcanic basin in southern Jiangxi Province. The Yanbei volcanic-intrusive complex mainly consists of dacitic-rhyolitic volcanic rocks, granite, granite porphyry and diabase dikes. In previous papers, the granite porphyry was considered as subvolcanic rocks, which came from the same single magma chamber with the volcanic rocks. In this study, zircon U-Pb ages and Hf isotope data, as well as whole-rock geochemical and Sr-Nd isotopic compositions of different magmatic units in the Yanbei complex are reported. Geochronologic results show that various magmatic units have different formation ages. The dacite yielded a zircon U-Pb age of 143 ± 1 Ma, and the granite porphyry has the emplacement age of 138 ± 1 Ma. Diabase dikes which represented the final stage of magmatism, yielded a zircon U-Pb age of 128 ± 1 Ma. Distinctive whole rock Sr-Nd and zircon Hf isotopic compositions suggest that these magmatic units were derived from different magma sources. The volcanic rocks were mainly derived from the partial melting of Paleoproterozoic metasedimentary rocks without additions of mantle-derived magma. The granite porphyry has an A-type geochemical affinity, and was derived from remelting of Paleo-Mesoproterozoic crustal source with involvement of a subordinate mantle-derived magma. The granite porphyry is also a typical stanniferous granite with high F (4070-6090 ppm) and Sn (7-39 ppm) contents. It underwent strongly crystal fractionation of plagioclase, K-feldspar, and accessory minerals (like apatite, Fe-Ti oxides), which may contribute to the tin mineralization. The diabase was derived by partial melting of enriched lithospheric mantle which had been metasomatised by slab-derived fluids. The change of magmatic sources reflected an increasing extensional tectonic environment, perhaps induced by slab rollback of subducted paleo-Pacific plate.

Reactivation of a tin oxide-containing catalyst

NASA Technical Reports Server (NTRS)

Brown, Kenneth G. (Inventor); Hess, Robert V. (Inventor); Paulin, Patricia A. (Inventor); Miller, Irvin M. (Inventor); Schryer, David R. (Inventor); Upchurch, Billy T. (Inventor); Sidney, Barry D. (Inventor); Wood, George M. (Inventor)

1989-01-01

A method for the reactivation of a tin oxide-containing catalyst of a CO.sub.2 laser is provided. First, the catalyst is pretreated by a standard procedure. When the catalyst experiences diminished activity during usage, the heated zone surrounding the catalyst is raised to a temperature which is the operating temperature of the laser and 400.degree. C. for approximately one hour. The catalyst is exposed to the same laser gas mixture during this period. The temperature of the heated zone is then lowered to the operating temperature of the CO.sub.2 laser.

A multinuclear solid-state NMR study of the dimethyltin chalcogenides ((CH 3) 2SnE) 3, E  S,Se,Te

NASA Astrophysics Data System (ADS)

Gay, Ian D.; Jones, C. H. W.; Sharma, R. D.

The solid-state NMR spectra, measured using MAS, are reported for 13C, 119Sn, 77Se, and 125Te in the compounds (Me 2SnE) 3, E  S, Se, or Te. For ((CH 3) 2SnS) 3, tetragonal, three inequivalent carbons and two inequivalent tins are observed consistent with a reinterpretation of the crystal structure data of this compound which shows a twofold axis through opposing tin and sulfur atoms, the molecule being in a twisted-boat conformation. For the monoclinic form six inequivalent carbons and three inequivalent tins were observed. Chemical shifts for 13C and 119Sn and the magnitudes of the 2JSn Sn coupling constants are reported. The tetragonal forms of ((CH 3) 2SnSe) 3 and ((CH 3) 2SnTe) 3 show the presence of two inequivalent tin and chalcogen atoms and three inequivalent carbons, again consistent with a twofold axis. In these compounds it is possible to identify the three different observed single-bond coupling constants with the distinct crystallographically determined tin-chalcogen bonds. The 13C, 119Sn, 77Se, and 125Te chemical shifts are reported, together with the magnitude of 1JSn E (E  Se or Te). In addition to isotropic shifts and couplings, chemical-shift anisotropies are reported for Sn, Se, and Te.

Effect of containers on the quality of Chemlali olive oil during storage.

PubMed

Gargouri, Boutheina; Zribi, Akram; Bouaziz, Mohamed

2015-04-01

This study is undertaken to determine the storage stability of Chemlali extra-virgin olive oil (EVOO) in different containers such as clear and dark glass bottles, polyethylene (PE) and tin containers. The different oil samples were stored under light at room temperature. Quality parameters monitored during a 6-month-storage period included: acidity, peroxide value (PV), spectrophotometric indices (K232 and K270), chlorophyll and carotene pigments, fatty acids and sterol compositions, total phenols, Rancimat induction time as well as sensory evaluation. Tin containers and dark glass bottles recorded the lowest oxidation values. In addition, oil packed in tin containers and dark glass bottles showed better physicochemical and organoleptic characteristics than that stored in clear glass bottles and PE containers. A significant decrease (p < 0.05) in the antioxidant contents (carotenes, chlorophylls and total phenols) was observed in the oil stored in the clear glass bottles and PE containers. Such results proved that the storage of oil in tin containers and dark glass bottles appeared most adequate, and showed a gradual loss of quality during storage, especially in PE containers and clear glass bottles. This study has shown that the best packaging materials for the commercial packing of Chemlali extra-virgin olive oil are tin containers and dark glass bottles.

Tin recovery from tin slag using electrolysis method

NASA Astrophysics Data System (ADS)

Jumari, Arif; Purwanto, Agus; Nur, Adrian; Budiman, Annata Wahyu; Lerian, Metty; Paramita, Fransisca A.

2018-02-01

The process in industry, including in mining industry, would surely give negative effect such as waste polluting to the environment. Some of waste could be potentially reutilized to be a commodity with the higher economic value. Tin slag is one of them. The aim of this research was to recover the tin contained in tin slag. Before coming to the electrolysis, tin slag must be treated by dissolution. The grinded tin slag was dissolved into HCl solution to form a slurry. During dissolution, the slurry was agitated and heated, and finally filtered. The filtrate obtained was then electrolyzed. During the process of electrolysis, solid material precipitated on the used cathode. The precipitated solid was then separated and dried. The solid was then analyzed using XRD, XRF and SEM. The XRD analysis showed that the longest time of dissolution and electrolysis the highest the purity obtained in the product. The SEM analysis showed that the longest time of electrolysis the smallest tin particle obtained. Optimum time achieved in this research was 2 hours for the recovering time and 3 hours for the electrolysis time, with 9% tin recovered.

A tillering inhibition gene influences root–shoot carbon partitioning and pattern of water use to improve wheat productivity in rainfed environments

PubMed Central

Hendriks, P.W.; Kirkegaard, J.A.; Lilley, J.M.; Gregory, P.J.; Rebetzke, G.J.

2016-01-01

Genetic modification of shoot and root morphology has potential to improve water and nutrient uptake of wheat crops in rainfed environments. Near-isogenic lines (NILs) varying for a tillering inhibition (tin) gene and representing multiple genetic backgrounds were phenotyped in contrasting, controlled environments for shoot and root growth. Leaf area, shoot and root biomass were similar until tillering, whereupon reduced tillering in tin-containing NILs produced reductions of up to 60% in total leaf area and biomass, and increases in total root length of up to 120% and root biomass to 145%. Together, the root-to-shoot ratio increased two-fold with the tin gene. The influence of tin on shoot and root growth was greatest in the cv. Banks genetic background, particularly in the biculm-selected NIL, and was typically strongest in cooler environments. A separate de-tillering study confirmed greater root-to-shoot ratios with regular tiller removal in non-tin-containing genotypes. In validating these observations in a rainfed field study, the tin allele had a negligible effect on seedling growth but was associated with significantly (P<0.05) reduced tiller number (–37%), leaf area index (–26%), and spike number (–35%) to reduce plant biomass (–19%) at anthesis. Root biomass, root-to-shoot ratio at early stem elongation, and root depth at maturity were all increased in tin-containing NILs. Soil water use was slowed in tin-containing NILs, resulting in greater water availability, greater stomatal conductance, cooler canopy temperatures, and maintenance of green leaf area during grain-filling. Together these effects contributed to increases in harvest index and grain yield. In both the controlled and field environments, the tin gene was commonly associated with increased root length and biomass, but the significant influence of genetic background and environment suggests careful assessment of tin-containing progeny in selection for genotypic increases in root growth. PMID:26494729

Ru-bis(pyridine)pyrazolate (bpp)-Based Water-Oxidation Catalysts Anchored on TiO2: The Importance of the Nature and Position of the Anchoring Group.

PubMed

Francàs, Laia; Richmond, Craig; Garrido-Barros, Pablo; Planas, Nora; Roeser, Stephan; Benet-Buchholz, Jordi; Escriche, Lluís; Sala, Xavier; Llobet, Antoni

2016-04-04

Three distinct functionalisation strategies have been applied to the in,in-[{Ru(II)(trpy)}2(μ-bpp)(H2O)2](3+) (trpy=2,2':6',2''-terpyridine, bpp=bis(pyridine)pyrazolate) water-oxidation catalyst framework to form new derivatives that can adsorb onto titania substrates. Modifications included the addition of sulfonate, carboxylate, and phosphonate anchoring groups to the terpyridine and bis(pyridyl)pyrazolate ligands. The complexes were characterised in solution by using 1D NMR, 2D NMR, and UV/Vis spectroscopic analysis and electrochemical techniques. The complexes were then anchored on TiO2-coated fluorinated tin oxide (FTO) films, and the reactivity of these new materials as water-oxidation catalysts was tested electrochemically through controlled-potential electrolysis (CPE) with oxygen evolution detected by headspace analysis with a Clark electrode. The results obtained highlight the importance of the catalyst orientation with respect to the titania surface in regard to its capacity to catalytically oxidize water to dioxygen. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structural Basis and Function of XRN2-Binding by XTB Domains

PubMed Central

Richter, Hannes; Katic, Iskra; Gut, Heinz; Großhans, Helge

2016-01-01

The ribonuclease XRN2 is an essential player in RNA metabolism. In Caenorhabditis elegans, XRN2 functions with PAXT-1, which shares a putative XRN2-binding domain (XTBD) with otherwise unrelated mammalian proteins. Here, we characterize structure and function of an XTBD – XRN2 complex. Although XTBD stably interconnects two XRN2 domains through numerous interacting residues, mutation of a single critical residue suffices to disrupt XTBD – XRN2 complexes in vitro, and recapitulates paxt-1 null mutant phenotypes in vivo. Demonstrating conservation of function, vertebrate XTBD-containing proteins bind XRN2 in vitro, and human CDKN2AIPNL (C2AIL) can substitute for PAXT-1 in vivo. In vertebrates, where three distinct XTBD-containing proteins exist, XRN2 may partition to distinct stable heterodimeric complexes, likely differing in subcellular localization or function. In C. elegans, complex formation with the unique PAXT-1 serves to preserve the stability of XRN2 in the absence of substrate. PMID:26779609

Models of grades and tonnages of some lode tin deposits

USGS Publications Warehouse

Menzie, W.D.; Reed, B.L.; Singer, Donald A.

1988-01-01

Descriptive and grade/tonnage models have recently been built for many types of deposits. Such models consist of descriptions of mineralogy, host rocks, ore textures, controls, alteration, geochemical signatures, age, and tectonic settings, together with statistical models of grades, tonnages, and contained metal of deposits of each type. The models are used to identify areas that may contain undiscovered deposits of given types, to convey to non-geologists an idea of the importance of such deposits, and to test and refine classifications of mineral deposits.Descriptive and grade/tonnage models have recently been built for five types of primary tin deposits: rhyolite-hosted such as in Mexico; hydrothermal lodes such as in Cornwall, England, and the Herberton district, Queensland; replacement (or exhalative?) such as Renison Bell, Tasmania; skarn such as at Lost River, Alaska; and greisen such as in the Erzgebirge. Analyses of frequency distributions of tonnage, contained metal, tin grades and the relationships between these variables show that the deposits fall into four well-defined domains that have definite geological characteristics. Rhyolite-hosted, or Mexican, deposits contain a median of 4 t of tin and have a median grade of 0.4% Sn. Hydrothermal lode deposits have the highest grades. Half of such deposits have grades over 1.0% Sn, and the majority contain more than 1,000 t Sn. Large hydrothermal vein deposits contain more than 50,000 t Sn. Replacement (or exhalative?) deposits contain the largest amount of tin (median = 40,000 t). They are only of slightly lower grade (median = 0.80% Sn) than the hydrothermal lodes. Greisen or stockwork deposits have larger tonnages than replacement deposits, but contain less tin (median = 25,000 t).They are also of much lower grade (median = 0.3% Sn). Though grades and tonnages are available for only four skarn deposits, they appear to be more like greisen deposits than replacement deposits when compared using grades, tonnage and contained tin.Although these individual models of primary tin deposits must be regarded as preliminary because of the relatively small number of deposits upon which they are built, they clearly demonstrate differences among types and provide basic information that can be useful in making decisions about exploration strategy, land classification, and tin supply.

A role for heterochromatin protein 1γ at human telomeres

PubMed Central

Canudas, Silvia; Houghtaling, Benjamin R.; Bhanot, Monica; Sasa, Ghadir; Savage, Sharon A.; Bertuch, Alison A.; Smith, Susan

2011-01-01

Human telomere function is mediated by shelterin, a six-subunit complex that is required for telomere replication, protection, and cohesion. TIN2, the central component of shelterin, has binding sites to three subunits: TRF1, TRF2, and TPP1. Here we identify a fourth partner, heterochromatin protein 1γ (HP1γ), that binds to a conserved canonical HP1-binding motif, PXVXL, in the C-terminal domain of TIN2. We show that HP1γ localizes to telomeres in S phase, where it is required to establish/maintain cohesion. We further demonstrate that the HP1-binding site in TIN2 is required for sister telomere cohesion and can impact telomere length maintenance by telomerase. Remarkably, the PTVML HP1-binding site is embedded in the recently identified cluster of mutations in TIN2 that gives rise to dyskeratosis congenita (DC), an inherited bone marrow failure syndrome caused by defects in telomere maintenance. We show that DC-associated mutations in TIN2 abrogate binding to HP1γ and that DC patient cells are defective in sister telomere cohesion. Our data indicate a novel requirement for HP1γ in the establishment/maintenance of cohesion at human telomeres and, furthermore, may provide insight into the mechanism of pathogenesis in TIN2-mediated DC. PMID:21865325

The dermatomyositis-specific autoantigen Mi2 is a component of a complex containing histone deacetylase and nucleosome remodeling activities.

PubMed

Zhang, Y; LeRoy, G; Seelig, H P; Lane, W S; Reinberg, D

1998-10-16

Histone acetylation and deacetylation were found to be catalyzed by structurally distinct, multisubunit complexes that mediate, respectively, activation and repression of transcription. ATP-dependent nucleosome remodeling, mediated by different multisubunit complexes, was thought to be involved only in transcription activation. Here we report the isolation of a protein complex that contains both histone deacetylation and ATP-dependent nucleosome remodeling activities. The complex contains the histone deacetylases HDAC1/2, histone-binding proteins, the dermatomyositis-specific autoantigen Mi2beta, a polypeptide related to the metastasis-associated protein 1, and a novel polypeptide of 32 kDa. Patients with dermatomyositis have a high rate of malignancy. The finding that Mi2beta exists in a complex containing histone deacetylase and nucleosome remodeling activities suggests a role for chromatin reorganization in cancer metastasis.

Pharmacokinetic Study of Di-Phenyl-Di-(2,4-Difluobenzohydroxamato)Tin(IV): Novel Metal-Based Complex with Promising Antitumor Potential

PubMed Central

Li, Yunlan; Gao, Zhuyan; Guo, Pu; Li, Qingshan

2012-01-01

Di-phenyl-di-(2,4-difluobenzohydroxamato)tin(IV)(DPDFT), a new metal-based arylhydroxamate antitumor complex, showed high in vivo and in vitro antitumor activity with relative low toxicity, but no data was reported regarding its pharmacokinetics and dependent toxicity. In this paper, a rapid, sensitive, and reproducible HPLC method in vivo using Diamonsil ODS column with a mixture of methanol and phosphoric acid in water (30 : 70, V/V, pH 3.0) as mobile phase was developed and validated for the determination of DPDFT. The plasma was deproteinized with methanol that contained acetanilide as the internal standard (I.S.). The photodiode array detector was set at a wavelength of 228 nm at room temperature and a linear curve over the concentration range 0.1~25 μg·mL−1 (r = 0.9993) was obtained. The method was used to determine the concentration-time profiles for DPDFT in the plasma after single intravenous administration with doses of 5, 10, 15 mg·kg−1 to rats. The pharmacokinetics parameter calculations and modeling were carried out using the 3p97 software. The results showed that the concentration-time curves of DPDFT in rat plasma could be fitted to two-compartment model. PMID:22400014

Spectral, thermal, XRD and SEM studies of charge-transfer complexation of hexamethylenediamine and three types of acceptors: π-, σ- and vacant orbital acceptors that include quinol, picric acid, bromine, iodine, SnCl4 and ZnCl2 acceptors

NASA Astrophysics Data System (ADS)

Adam, Abdel Majid A.; Refat, Moamen S.; Saad, Hosam A.

2013-11-01

In this work, structural, thermal, morphological and pharmacological characterization was performed on the interactions between a hexamethylenediamine (HMDA) donor and three types of acceptors to understand the complexation behavior of diamines. The three types of acceptors include π-acceptors (i.e., quinol (QL) and picric acid (PA)), σ-acceptors (i.e., bromine and iodine) and vacant orbital acceptors (i.e., tin(IV) tetrachloride (SnCl4) and zinc chloride (ZnCl2)). The characterization of the obtained CT complexes was performed using elemental analysis, infrared (IR), Raman, 1H NMR and electronic absorption spectroscopy, powder X-ray diffraction (XRD) and thermogravimetric (TG) analysis. Their morphologies were studied using scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). The biological activities of the obtained CT complexes were tested for their antibacterial activities. The complex containing the QL acceptor exhibited a remarkable electronic spectrum with a strong, broad absorption band, which had an observed λmax that was at a much longer wavelength than those of the free reactants. In addition, this complex exhibited strong antimicrobial activities against various bacterial and fungal strains compared to standard drugs. The complexes containing the PA, iodine, Sn(IV) and Zn(II) acceptors exhibited good thermal stability up to 240, 330, 275 and 295 °C, respectively. The complexes containing bromine, Sn(IV) and Zn(II) acceptors exhibited good crystallinity. In addition to its good crystallinity properties, the complex containing the bromine acceptor exhibits a remarkable morphology feature.

Synthesis, crystal structures and coordination modes of some triorganotin(IV) complexes with 2-N-propyl and 2-N-benzyl-amino-1-cyclopentene-1-dithiocarboxylates

NASA Astrophysics Data System (ADS)

López-Cardoso, Marcela; Vargas-Pineda, Gabriela; Román-Bravo, Perla Patricia; Rodríguez-Narváez, Cristina; Rosas-Valdez, Elena; Cea-Olivares, Raymundo

2016-07-01

The syntheses and characterization of six new triorganotin(IV) complexes, Ph3Sn(PrACDA) (1), Bu3Sn(PrACDA) (2), Ph3Sn(BzACDA) (3), Bu3Sn(BzACDA) (4), Me3Sn(BzACDA) (5) and Cy3Sn(BzACDA) (6) (ACDA = 2-amino-1-cyclopentene-1-carbodithioate anion) are reported. Compounds 1-6 were synthesized by the reaction between the sodium salts of 2-N-propyl- or 2-N-benzyl-2-amino-1-cyclopentene-1-carbodithioate and R3SnCl (R = Ph, Bu, Me, Cy) in a 1:1 M ratio. The complexes were characterized by elemental analyses, IR and NMR (1H, 13C and 119Sn) spectroscopy and by FAB+ mass spectrometry. The experimental data reveal that the tin atom is coordinated to the ligand by means of the two sulfur atoms from the carbodithioate group in an anisobidentate mode, while the 119Sn{1H} NMR spectra suggest a pentacoordinate metal center in 1-4 and a tetracoordinate tin atom for 5 and 6. The molecular structures of complexes 1, 3 and 5 were confirmed by single crystal X-ray diffraction analysis showing the presence of N-H···S hydrogen bonding and a distorted trigonal bipyramid geometry for the tin atoms.

Investigating Sodium Storage Mechanisms in Tin Anodes: A Combined Pair Distribution Function Analysis, Density Functional Theory, and Solid-State NMR Approach.

PubMed

Stratford, Joshua M; Mayo, Martin; Allan, Phoebe K; Pecher, Oliver; Borkiewicz, Olaf J; Wiaderek, Kamila M; Chapman, Karena W; Pickard, Chris J; Morris, Andrew J; Grey, Clare P

2017-05-31

The alloying mechanism of high-capacity tin anodes for sodium-ion batteries is investigated using a combined theoretical and experimental approach. Ab initio random structure searching (AIRSS) and high-throughput screening using a species-swap method provide insights into a range of possible sodium-tin structures. These structures are linked to experiments using both average and local structure probes in the form of operando pair distribution function analysis, X-ray diffraction, and 23 Na solid-state nuclear magnetic resonance (ssNMR), along with ex situ 119 Sn ssNMR. Through this approach, we propose structures for the previously unidentified crystalline and amorphous intermediates. The first electrochemical process of sodium insertion into tin results in the conversion of crystalline tin into a layered structure consisting of mixed Na/Sn occupancy sites intercalated between planar hexagonal layers of Sn atoms (approximate stoichiometry NaSn 3 ). Following this, NaSn 2 , which is predicted to be thermodynamically stable by AIRSS, forms; this contains hexagonal layers closely related to NaSn 3 , but has no tin atoms between the layers. NaSn 2 is broken down into an amorphous phase of approximate composition Na 1.2 Sn. Reverse Monte Carlo refinements of an ab initio molecular dynamics model of this phase show that the predominant tin connectivity is chains. Further reaction with sodium results in the formation of structures containing Sn-Sn dumbbells, which interconvert through a solid-solution mechanism. These structures are based upon Na 5-x Sn 2 , with increasing occupancy of one of its sodium sites commensurate with the amount of sodium added. ssNMR results indicate that the final product, Na 15 Sn 4 , can store additional sodium atoms as an off-stoichiometry compound (Na 15+x Sn 4 ) in a manner similar to Li 15 Si 4 .

Investigating Sodium Storage Mechanisms in Tin Anodes: A Combined Pair Distribution Function Analysis, Density Functional Theory, and Solid-State NMR Approach

DOE PAGES

Stratford, Joshua M.; Mayo, Martin; Allan, Phoebe K.; ...

2017-05-04

Here, the alloying mechanism of high-capacity tin anodes for sodium-ion batteries is investigated using a combined theoretical and experimental approach. Ab initio random structure searching (AIRSS) and high-throughput screening using a species-swap method provide insights into a range of possible sodium–tin structures. These structures are linked to experiments using both average and local structure probes in the form of operando pair distribution function analysis, X-ray diffraction, and 23Na solid-state nuclear magnetic resonance (ssNMR), along with ex situ 119Sn ssNMR. Through this approach, we propose structures for the previously unidentified crystalline and amorphous intermediates. The first electrochemical process of sodium insertionmore » into tin results in the conversion of crystalline tin into a layered structure consisting of mixed Na/Sn occupancy sites intercalated between planar hexagonal layers of Sn atoms (approximate stoichiometry NaSn 3). Following this, NaSn 2, which is predicted to be thermodynamically stable by AIRSS, forms; this contains hexagonal layers closely related to NaSn 3, but has no tin atoms between the layers. NaSn 2 is broken down into an amorphous phase of approximate composition Na 1.2Sn. Reverse Monte Carlo refinements of an ab initio molecular dynamics model of this phase show that the predominant tin connectivity is chains. Further reaction with sodium results in the formation of structures containing Sn–Sn dumbbells, which interconvert through a solid-solution mechanism. These structures are based upon Na 5–xSn 2, with increasing occupancy of one of its sodium sites commensurate with the amount of sodium added. ssNMR results indicate that the final product, Na 15Sn 4, can store additional sodium atoms as an off-stoichiometry compound (Na 15+xSn 4) in a manner similar to Li 15Si 4.« less

Investigating Sodium Storage Mechanisms in Tin Anodes: A Combined Pair Distribution Function Analysis, Density Functional Theory, and Solid-State NMR Approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stratford, Joshua M.; Mayo, Martin; Allan, Phoebe K.

Here, the alloying mechanism of high-capacity tin anodes for sodium-ion batteries is investigated using a combined theoretical and experimental approach. Ab initio random structure searching (AIRSS) and high-throughput screening using a species-swap method provide insights into a range of possible sodium–tin structures. These structures are linked to experiments using both average and local structure probes in the form of operando pair distribution function analysis, X-ray diffraction, and 23Na solid-state nuclear magnetic resonance (ssNMR), along with ex situ 119Sn ssNMR. Through this approach, we propose structures for the previously unidentified crystalline and amorphous intermediates. The first electrochemical process of sodium insertionmore » into tin results in the conversion of crystalline tin into a layered structure consisting of mixed Na/Sn occupancy sites intercalated between planar hexagonal layers of Sn atoms (approximate stoichiometry NaSn 3). Following this, NaSn 2, which is predicted to be thermodynamically stable by AIRSS, forms; this contains hexagonal layers closely related to NaSn 3, but has no tin atoms between the layers. NaSn 2 is broken down into an amorphous phase of approximate composition Na 1.2Sn. Reverse Monte Carlo refinements of an ab initio molecular dynamics model of this phase show that the predominant tin connectivity is chains. Further reaction with sodium results in the formation of structures containing Sn–Sn dumbbells, which interconvert through a solid-solution mechanism. These structures are based upon Na 5–xSn 2, with increasing occupancy of one of its sodium sites commensurate with the amount of sodium added. ssNMR results indicate that the final product, Na 15Sn 4, can store additional sodium atoms as an off-stoichiometry compound (Na 15+xSn 4) in a manner similar to Li 15Si 4.« less

Use of tin-117m to study the role of tin in the direct labeling of proteins with rhenium-188

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dadachova, E.; Mirzadeh, S.; Knapp, F.F. Jr.

1996-05-01

Sn-117m provided an opportunity to study the effect of [Sn(II)] on the complexation of carrier-free Re-188, radiolabeling efficiency and incorporation of Sn into reduced IgG. Endogenous thiols of the IgG were exposed using dithiothreitol. Reduction of Re-188 was achieved with SnCl{sub 2} [spiked with Sn-117m(II)] in either gluconate(Glu) or citrate(Cit) buffer at pH=4.2. Concentration of Sn(II) varied from 5x10{sup -4} to 1 mg per mg protein. Complexation of reduced Re-188 was monitored by ITLC-SG, and protein was monitored by HPLC. Complexation of Re-188 at [Sn(II)]=5x10{sup -4} mg was higher in Cit (20%) than in Glu (10%); at 5x10{sup -2} mgmore » - 50% in both buffers; and at 1 mg - higher in Glu (95%) than in Cit (60%). The efficiency of protein labeling was considerably higher in Glu than in Cit for the entire range of [Sn(II)]. Experiments with Sn-117m demonstrated that the absolute amount of Sn(II) associated with protein increased with increasing [Sn(II)], and distinct saturation levels were found for both Glu and Cit. Saturation levels were 6.4 and 33 {mu}g of Sn/mg of protein for Flu and Cit, respectively (19 and 48% incorporation). For all [Sn(II)] studied, the amount of Sn bound to the protein was 5-10 times higher in Cit than in Glu. In summary, Glu seems to release Re for transchelation to the protein more readily than Cit. Simultaneously, it complexes Sn(II) more efficiently than Cit thus preventing competition between Re and Sn for thiol groups. These data provide additional insights into the mechanism of direct labeling of proteins with carrier-free Re-188 as well as into the choice of supporting ligand for direct labeling.« less

Structural and Optoelectronic Properties of SnO2 Thin Films Doped by Group-Ia Elements

NASA Astrophysics Data System (ADS)

Benhebal, Hadj; Benrabah, Bedhiaf; Ammari, Aek; Madoune, Yacine; Lambert, Stéphanie D.

This paper presents the results of an experimental work devoted to the synthesis and the characterization of tin dioxide (SnO2) thin layers doped with group-IA elements (Li, Na and K). The materials were synthesized by the sol-gel method and deposited by dip-coating, using tin (II) chloride dihydrate as a source of tin and absolute ethyl alcohol as solvent. Thin films prepared were characterized by several techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (IR), visible and ultraviolet spectroscopy and complex impedance method. The results obtained show that the materials kept their tetragonal rutile structure with preferred orientation of (101), whereas doping leads to a reduction of their energy band gap. The complex impedance analysis suggests that the different processes occurring at the electrode interface are modeled by an electrical circuit not affected by the doping.

Heteroleptic tin(II) initiators for the ring-opening (co)polymerization of lactide and trimethylene carbonate: mechanistic insights from experiments and computations.

PubMed

Wang, Lingfang; Kefalidis, Christos E; Sinbandhit, Sourisak; Dorcet, Vincent; Carpentier, Jean-François; Maron, Laurent; Sarazin, Yann

2013-09-27

The tin(II) complexes {LO(x)}Sn(X) ({LO(x)}(-) =aminophenolate ancillary) containing amido (1-4), chloro (5), or lactyl (6) coligands (X) promote the ring-opening polymerization (ROP) of cyclic esters. Complex 6, which models the first insertion of L-lactide, initiates the living ROP of L-LA on its own, but the amido derivatives 1-4 require the addition of alcohol to do so. Upon addition of one to ten equivalents of iPrOH, precatalysts 1-4 promote the ROP of trimethylene carbonate (TMC); yet, hardly any activity is observed if tert-butyl (R)-lactate is used instead of iPrOH. Strong inhibition of the reactivity of TMC is also detected for the simultaneous copolymerization of L-LA and TMC, or for the block copolymerization of TMC after that of L-LA. Experimental and computational data for the {LO(x)}Sn(OR)complexes (OR=lactyl or lactidyl) replicating the active species during the tin(II)-mediated ROP of L-LA demonstrate that the formation of a five-membered chelate is largely favored over that of an eight-membered one, and that it constitutes the resting state of the catalyst during this (co)polymerization. Comprehensive DFT calculations show that, out of the four possible monomer insertion sequences during simultaneous copolymerization of L-LA and TMC: 1) TMC then TMC, 2) TMC then L-LA, 3) L-LA then L-LA, and 4) L-LA then TMC, the first three are possible. By contrast, insertion of L-LA followed by that of TMC (i.e., insertion sequence 4) is endothermic by +1.1 kcal mol(-1), which compares unfavorably with consecutive insertions of two L-LA units (i.e., insertion sequence 3) (-10.2 kcal mol(-1)). The copolymerization of L-LA and TMC thus proceeds under thermodynamic control. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Laser-produced plasma EUV source using a colloidal microjet target containing tin dioxide nanoparticles

NASA Astrophysics Data System (ADS)

Higashiguchi, Takeshi; Dojyo, Naoto; Sasaki, Wataru; Kubodera, Shoichi

2006-10-01

We realized a low-debris laser-produced plasma extreme ultraviolet (EUV) source by use of a colloidal microjet target, which contained low-concentration (6 wt%) tin-dioxide nanoparticles. An Nd:YAG laser was used to produce a plasma at the intensity on the order of 10^11 W/cm^2. The use of low concentration nanoparticles in a microjet target with a diameter of 50 μm regulated the neutral debris emission from a target, which was monitored by a silicon witness plate placed 30 cm apart from the source in a vacuum chamber. No XPS signals of tin and/or oxygen atoms were observed on the plate after ten thousand laser exposures. The low concentration nature of the target was compensated and the conversion efficiency (CE) was improved by introducing double pulses of two Nd:YAG lasers operated at 532 and 1064 nm as a result of controlling the micro-plasma characteristics. The EUV CE reached its maximum of 1.2% at the delay time of approximately 100 ns with the main laser intensiy of 2 x10^11 W/cm^2. The CE value was comparable to that of a tin bulk target, which, however, produced a significant amount of neutral debris.

Method of preparing composite superconducting wire

DOEpatents

Verhoeven, John D.; Gibson, Edwin D.; Finnemore, Douglas K.; Ostenson, Jerome E.; Schmidt, Frederick A.; Owen, Charles V.

1985-08-06

An improved method of preparing composite multifilament superconducting wire of Nb.sub.3 Sn in a copper matrix which eliminates the necessity of coating the drawn wire with tin. A generalized cylindrical billet of an alloy of copper containing at least 15 weight percent niobium, present in the copper as discrete, randomly distributed and oriented dendritic-shaped particles, is provided with at least one longitudinal opening which is filled with tin to form a composite drawing rod. The drawing rod is then drawn to form a ductile composite multifilament wire containing a filament of tin. The ductile wire containing the tin can then be wound into magnet coils or other devices before heating to diffuse the tin through the wire to react with the niobium forming Nb.sub.3 Sn. Also described is an improved method for making large billets of the copper-niobium alloy by consumable-arc casting.

Improved method of preparing composite superconducting wire

DOEpatents

Verhoeven, J.D.; Gibson, E.D.; Finnemore, D.K.; Ostenson, J.E.; Schmidt, F.A.; Owen, C.V.

1979-10-17

An improved method of preparing composite multifilament superconducting wire of Nb/sub 3/Sn in a copper matrix eliminates the necessity of coating the drawn wire with tin. A generalized cylindrical billet of an alloy of copper containing at least 15 weight percent niobium, present in the copper as discrete, randomly distributed and oriented dendritic-shaped particles, is provided with at least one longitudinal opening which is filled with tin to form a composite drawing rod. The drawing rod is then drawn to form a ductile composite multifilament wire containing a filament of tin. The ductile wire containing the tin can then be wound into magnet coils or other devices before heating to diffuse the tin through the wire to react with the niobium forming Nb/sub 3/Sn. Also described is an improved method for making large billets of the copper-niobium alloy by consumable-arc casting.

Tin

USGS Publications Warehouse

Kamilli, Robert J.; Kimball, Bryn E.; Carlin, James F.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Tin (Sn) is one of the first metals to be used by humans. Almost without exception, tin is used as an alloy. Because of its hardening effect on copper, tin was used in bronze implements as early as 3500 B.C. The major uses of tin today are for cans and containers, construction materials, transportation materials, and solder. The predominant ore mineral of tin, by far, is cassiterite (SnO2).In 2015, the world’s total estimated mine production of tin was 289,000 metric tons of contained tin. Total world reserves at the end of 2016 were estimated to be 4,700,000 metric tons. China held about 24 percent of the world’s tin reserves and accounted for 38 percent of the world’s 2015 production of tin.The proportion of scrap used in tin production is between 10 and 25 percent. Unlike many metals, tin recycling is relatively efficient, and the fraction of tin in discarded products that get recycled is greater than 50 percent.Only about 20 percent of the world’s identified tin resources occur as primary hydrothermal hard-rock veins, or lodes. These lodes contain predominantly high-temperature minerals and almost invariably occur in close association with silicic, peraluminous granites. About 80 percent of the world’s identified tin resources occur as unconsolidated secondary or placer deposits in riverbeds and valleys or on the sea floor. The largest concentration of both onshore and offshore placers is in the extensive tin belt of Southeast Asia, which stretches from China in the north, through Thailand, Burma (also referred to as Myanmar), and Malaysia, to the islands of Indonesia in the south. Furthermore, tin placers are almost always found closely allied to the granites from which they originate. Other countries with significant tin resources are Australia, Bolivia, and Brazil.Most hydrothermal tin deposits belong to what can be thought of as a superclass of porphyry-greisen deposits. The hydrothermal tin deposits are all characterized by a close spatial, temporal, and genetic association with highly differentiated, peraluminous porphyritic granite intrusions. The intrusions form pegmatites; disseminated ore; parallel or subparallel, greisen-bordered sheeted veins that either cross-cut the intrusion or are peripheral to it; skarns; and (or) limestone replacements that contain different amounts of cassiterite, molybdenite, and wolframite.The tectonic settings of tin-bearing granites are relatively well understood and of limited variety. Tin and tungsten deposits and their associated igneous rocks are found mainly in continental settings.Historically, prospecting for tin has been carried out by the time-honored methods of panning, drilling, trenching, and assaying. Geophysical and geochemical surveys have been employed to cover large areas more rapidly, isolating areas of possible tin deposits so that drilling can be more effective and less costly. Elemental concentrations and relationships of the lithophile elements, especially barium, lithium, niobium, potassium, rubidium, and zirconium, are the most reliable chemical indicators of ore-forming processes and tin-bearing potential.The average human diet includes an intake of about 10 milligrams per day of tin. Ingestion of tin in significantly greater amounts than 10 milligrams per day may lead to a stomach ache, anemia, and liver and kidney problems. Exposure to some organo-tin compounds can interfere with brain and nervous system function and, in severe cases, can cause death. Extended inhalation of tin oxide—an issue mainly for those people who work in the tin industry—results in a higher potential to develop stannosis, which is a mild disease of the lungs caused by the inhalation of tin-bearing dust. Inorganic tin is poorly absorbed by the body, and no evidence exists for the carcinogenicity of metallic tin and tin compounds in humans.Most placer tin deposits are mined by open pit and (or) dredging methods. Mining of alluvial placers in modern streambeds and riverbeds is likely to increase the amount of sediment delivered downstream. This, combined with potential diversion of rivers and streams, may negatively affect downstream ecosystems. Many of the placer deposits located in Burma, Indonesia, Malaysia, and Thailand are located offshore. Most offshore placer tin deposits are mined by dredging methods, which have the potential to negatively affect benthic, midwater, and pelagic ecosystems.In a congressionally mandated U.S. Department of Defense study of strategic minerals published in 2013, tin has the greatest shortfall amount (insufficient supply to meet demand) at \\$416 million; this amount is more than twice that of antimony ($182 million), which is the strategic mineral with the next largest shortfall amount (U.S. Department of Defense, 2013). The United States imported 75 percent of its tin supply in 2015. During the period 2012–15, these imports were from, in descending order of amount imported, Peru, Indonesia, Malaysia, and Bolivia.A promising advancement concerning research into the origin of tin deposits is the recent development of a reliable method of analyzing tin isotopes in cassiterite. Although the mechanism of transport and deposition of tin is fairly well understood, the means by which tin is incorporated into the parent magma at the points of magma generation and ascent needs further investigation.Tin metallogenic provinces worldwide are well known. Consequently, any undiscovered tin deposits will likely be spatially close to known deposits or extensions of the same.

Hollow tin/chromium whiskers

NASA Astrophysics Data System (ADS)

Cheng, Jing; Vianco, Paul T.; Li, James C. M.

2010-05-01

Tin whiskers have been an engineering challenge for over five decades. The mechanism has not been agreed upon thus far. This experiment aimed to identify a mechanism by applying compressive stresses to a tin film evaporated on silicon substrate with an adhesion layer of chromium in between. A phenomenon was observed in which hollow whiskers grew inside depleted areas. Using focused ion beam, the hollow whiskers were found to contain both tin and chromium. At the bottom of the depleted areas, thin tin/tin oxide film remained over the chromium layer. It indicates that tin transport occurred along the interface between tin and chromium layers.

Biosorption of inorganic tin and methyltin compounds by estuarine macroalgae

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, P.J.; Weber, J.H.

1991-02-01

Biosorption kinetics of total recoverable inorganic tin (TRISn), MeSn{sup 3+}, Me{sub 2}Sn{sup 2+}, and Me{sub 3}Sn{sup +} compounds onto tissue from the macroalga Fucus vesiculosus and onto a mixed community of Enteromorpha spp. (a filamentous genus) showed that after 48-h accumulation of tin compounds followed the trend TRISn {approximately} MeSn{sup 3+} > Me{sub 2}Sn{sup 2+} > Me{sub 3}Sn{sup +}. Uptake of tin compounds onto F. vesiculosus consisted of three phases: rapid phase 1, intermediate phase 2 (modeled by first-order kinetics). Uptake of tin compounds by Enteromorpha spp. occurred in rapid phase 1 and intermediate, saturating phase 2, which was completemore » in 3 h for TRISn and MeSn{sup 3+} and in 18 h for Me{sub 2}Sn{sup 2+} and Me{sub 2}Sn{sup 2+} and Me{sub 3}Sn{sup +}. After 24 h, (TRISn) and (MeSn{sup 3+}) in dark-incubated plants, suggesting active uptake processes during phase 3. Enteromorpha spp. incubated in the dark for 1 h contained significantly less TRISn and MeSn{sup 3+}, but not less Me{sub 2}Sn{sup 2+} and Me{sub 3}Sn{sup +}, than light-incubated plants. Interactions with different compartments of the algal thallus account for differences in amounts of biosorbed tin compounds. Initial phase 1 biosorption by both algae was probably adsorption onto the thallus surface.« less

Tin, Bismuth, and Tin-Bismuth Alloy Electrodeposition from Chlorometalate Salts in Deep Eutectic Solvents.

PubMed

Vieira, Luciana; Burt, Jennifer; Richardson, Peter W; Schloffer, Daniel; Fuchs, David; Moser, Alwin; Bartlett, Philip N; Reid, Gillian; Gollas, Bernhard

2017-06-01

The electrodeposition of tin, bismuth, and tin-bismuth alloys from Sn II and Bi III chlorometalate salts in the choline chloride/ethylene glycol (1:2 molar ratio) deep eutectic solvent was studied on glassy carbon and gold by cyclic voltammetry, rotating disc voltammetry, and chronoamperometry. The Sn II -containing electrolyte showed one voltammetric redox process corresponding to Sn II /Sn 0 . The diffusion coefficient of [SnCl 3 ] - , detected as the dominating species by Raman spectroscopy, was determined from Levich and Cottrell analyses. The Bi III -containing electrolyte showed two voltammetric reduction processes, both attributed to Bi III /Bi 0 . Dimensionless current/time transients revealed that the electrodeposition of both Sn and Bi on glassy carbon proceeded by 3D-progressive nucleation at a low overpotential and changed to instantaneous at higher overpotentials. The nucleation rate of Bi on glassy carbon was considerably smaller than that of Sn. Elemental Sn and Bi were electrodeposited on Au-coated glass slides from their respective salt solutions, as were Sn-Bi alloys from a 2:1 Sn II /Bi III solution. The biphasic Sn-Bi alloys changed from a Bi-rich composition to a Sn-rich composition by making the deposition potential more negative.

38 CFR 61.12 - Capital grant application packages-threshold requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... contains the Employer Identification Number or Taxpayer Identification Number (EIN/TIN) that corresponds to... must provide such an IRS determination letter, which includes their EIN/TIN. Applicants that apply under a group EIN/TIN must be identified by the parent EIN/TIN as a member or sub-unit of the parent EIN...

38 CFR 61.12 - Capital grant application packages-threshold requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... contains the Employer Identification Number or Taxpayer Identification Number (EIN/TIN) that corresponds to... must provide such an IRS determination letter, which includes their EIN/TIN. Applicants that apply under a group EIN/TIN must be identified by the parent EIN/TIN as a member or sub-unit of the parent EIN...

The effect of Sn on the reactions of n-hexane and cyclohexane over polycrystalline Pt foils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fujikawa, T.; Ribeiro, F.H.; Somorjai, G.A.

The modification of the catalytic properties of a polycrystalline platinum foil by the addition of tin was studied by the reactions of n-hexane and cyclohexane in excess H{sub 2}. The reactions were studied at 13.3 kPa of n-hexane, 450 kPa of H{sub 2} and 740 K, and 6.7 kPa of cyclohexane, 450 kPa of H{sub 2} and 573 K. The Pt-Sn catalyst was characterized by Auger electron spectroscopy and by temperature-programmed desorption of CO before and after the reactions. The sites that bind CO most strongly on the Pt foil also have the highest initial turnover rate and are themore » first ones to be poisoned by carbon deposits from hydrocarbon reactions or by sulfur when a sulfur-containing compound (thiophene) is present in the feed. The addition of tin can block these sites preferentially, thus decreasing the undesirable high initial hydrogenolysis rate of platinum catalysts in reforming reactions and eliminating the need for presulfiding the catalyst. Also, tin suppressed the hydrogenolysis reaction preferentially to the isomerization and cyclization reactions thus increasing the selectivities to isomerization and cyclization. The amount of carbon deposited was smaller on tin containing platinum catalysts during the dehydrogenation of cyclohexane and n-hexane.« less

Steady state and time resolved optical characterization studies of Zn 2SnO 4 nanowires for solar cell applications

DOE PAGES

Yakami, Baichhabi R.; Poudyal, Uma; Nandyala, Shashank R.; ...

2016-10-25

Nanowires are a promising option for sensitized solar cells, sensors, and display technology. Most of the work thus far has focused on binary oxides for these nanowires, but ternary oxides have advantages in additional control of optical and electronic properties. Here, we report on the diffuse reflectance, Low Temperature and Room Temperature Photoluminescence (PL), PL excitation spectrum, and Time Resolved PL (TRPL) of Zinc Tin Oxide (ZTO) nanowires grown by Chemical Vapor Deposition. The PL from the ZTO nanowires does not exhibit any band gap or near gap emission, and the diffuse reflectance measurement confirms that these ZTO nanowires havemore » a direct forbidden transition. The broad PL spectrum reveals two Gaussian peaks centered at 1.86 eV (red) and 2.81 eV (blue), representing two distinct defect states or complexes. The PL spectra were further studied by the Time Resolved Emission Spectrum and intensity dependent PL and TRPL. The time resolved measurements show complex non-exponential decays at all wavelengths, indicative of defect to defect transitions, and the red emissive states decay much slower than the blue emissive states. The effects of annealing in air and vacuum are studied to investigate the origin of the defect states in the nanowires, showing that the blue states are related to oxygen vacancies. We propose an energy band model for the nanowires containing defect states within the band gap and the associated transitions between these states that are consistent with our measurements.« less

Steady state and time resolved optical characterization studies of Zn 2SnO 4 nanowires for solar cell applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yakami, Baichhabi R.; Poudyal, Uma; Nandyala, Shashank R.

Nanowires are a promising option for sensitized solar cells, sensors, and display technology. Most of the work thus far has focused on binary oxides for these nanowires, but ternary oxides have advantages in additional control of optical and electronic properties. Here, we report on the diffuse reflectance, Low Temperature and Room Temperature Photoluminescence (PL), PL excitation spectrum, and Time Resolved PL (TRPL) of Zinc Tin Oxide (ZTO) nanowires grown by Chemical Vapor Deposition. The PL from the ZTO nanowires does not exhibit any band gap or near gap emission, and the diffuse reflectance measurement confirms that these ZTO nanowires havemore » a direct forbidden transition. The broad PL spectrum reveals two Gaussian peaks centered at 1.86 eV (red) and 2.81 eV (blue), representing two distinct defect states or complexes. The PL spectra were further studied by the Time Resolved Emission Spectrum and intensity dependent PL and TRPL. The time resolved measurements show complex non-exponential decays at all wavelengths, indicative of defect to defect transitions, and the red emissive states decay much slower than the blue emissive states. The effects of annealing in air and vacuum are studied to investigate the origin of the defect states in the nanowires, showing that the blue states are related to oxygen vacancies. We propose an energy band model for the nanowires containing defect states within the band gap and the associated transitions between these states that are consistent with our measurements.« less

Electrochemical Formation of Multilayer SnO2-Sb x O y Coating in Complex Electrolyte

NASA Astrophysics Data System (ADS)

Maizelis, Antonina; Bairachniy, Boris

2017-02-01

The multilayer antimony-doped tin dioxide coating was obtained by cathodic deposition of multilayer metal-hydroxide coating with near 100-nm thickness layers on the alloy underlayer accompanied by the anodic oxidation of this coating. The potential regions of deposition of tin, antimony, tin-antimony alloy, and mixture of this metals and their hydroxides in the pyrophosphate-tartrate electrolyte were revealed by the cyclic voltammetric method. The possibility of oxidation of cathodic deposit consisting of tin and Sn(II) hydroxide compounds to the hydrated tin dioxide in the same electrolyte was demonstrated. The operations of alloy underlayer deposition and oxidation of multilayer metal-hydroxide coating were proposed to carry out in the diluted pyrophosphate-tartrate electrolyte, similar to the main electrolyte. The accelerated tests showed higher service life of the titanium electrode with multilayer antimony-doped tin dioxide coating compared to both electrode with single-layer electrodeposited coating and the electrode with the coating obtained using prolonged heat treatment step.

Electrochemical Formation of Multilayer SnO2-Sb x O y Coating in Complex Electrolyte.

PubMed

Maizelis, Antonina; Bairachniy, Boris

2017-12-01

The multilayer antimony-doped tin dioxide coating was obtained by cathodic deposition of multilayer metal-hydroxide coating with near 100-nm thickness layers on the alloy underlayer accompanied by the anodic oxidation of this coating. The potential regions of deposition of tin, antimony, tin-antimony alloy, and mixture of this metals and their hydroxides in the pyrophosphate-tartrate electrolyte were revealed by the cyclic voltammetric method. The possibility of oxidation of cathodic deposit consisting of tin and Sn(II) hydroxide compounds to the hydrated tin dioxide in the same electrolyte was demonstrated.The operations of alloy underlayer deposition and oxidation of multilayer metal-hydroxide coating were proposed to carry out in the diluted pyrophosphate-tartrate electrolyte, similar to the main electrolyte.The accelerated tests showed higher service life of the titanium electrode with multilayer antimony-doped tin dioxide coating compared to both electrode with single-layer electrodeposited coating and the electrode with the coating obtained using prolonged heat treatment step.

Spectral and thermal studies with anti-fungal aspects of some organotin(IV) complexes with nitrogen and sulphur donor ligands derived from 2-phenylethylamine

NASA Astrophysics Data System (ADS)

Singh, Rajeev; Kaushik, N. K.

2008-11-01

Some complexes of 2-phenylethyl dithiocarbamate, thiohydrazides and thiodiamines with dibenzyltin(IV) chloride, tribenzyltin(IV) chloride and di( para-chlorobenzyl)tin(IV) dichloride have been synthesized and investigated in 1:2 and 1:1 molar ratio. The dithiocarbamate ligand act as monoanionic bidentate and thiohydrazide, thiodiamines act as neutral bidentate ligand. The synthesized complexes have been characterized by elemental analysis and molecular weight determination studies and their bonding pattern suggested on the basis of electronic, infrared, 1H and 13C NMR spectroscopy. Using thermogravimetric (TG) and differential thermal analysis (DTA) various thermodynamic and kinetic parameters viz. reaction order ( n), apparent activation energy ( Ea), apparent activation entropy ( S#) and heat of reaction (Δ H) have been calculated and correlated with the structural aspects for solid-state decomposition of complexes. The ligands and their tin complexes have also been screened for their fungitoxicity activity against Rhizoctonia solanii and Sclerotium rolfsii and their ED 50 values calculated.

Spectral and thermal studies with anti-fungal aspects of some organotin(IV) complexes with nitrogen and sulphur donor ligands derived from 2-phenylethylamine.

PubMed

Singh, Rajeev; Kaushik, N K

2008-11-15

Some complexes of 2-phenylethyl dithiocarbamate, thiohydrazides and thiodiamines with dibenzyltin(IV) chloride, tribenzyltin(IV) chloride and di(para-chlorobenzyl)tin(IV) dichloride have been synthesized and investigated in 1:2 and 1:1 molar ratio. The dithiocarbamate ligand act as monoanionic bidentate and thiohydrazide, thiodiamines act as neutral bidentate ligand. The synthesized complexes have been characterized by elemental analysis and molecular weight determination studies and their bonding pattern suggested on the basis of electronic, infrared, 1H and 13C NMR spectroscopy. Using thermogravimetric (TG) and differential thermal analysis (DTA) various thermodynamic and kinetic parameters viz. reaction order (n), apparent activation energy (Ea), apparent activation entropy (S#) and heat of reaction (DeltaH) have been calculated and correlated with the structural aspects for solid-state decomposition of complexes. The ligands and their tin complexes have also been screened for their fungitoxicity activity against Rhizoctonia solanii and Sclerotium rolfsii and their ED50 values calculated.

Two-dimensional tin selenide nanostructures for flexible all-solid-state supercapacitors.

PubMed

Zhang, Chunli; Yin, Huanhuan; Han, Min; Dai, Zhihui; Pang, Huan; Zheng, Yulin; Lan, Ya-Qian; Bao, Jianchun; Zhu, Jianmin

2014-04-22

Due to their unique electronic and optoelectronic properties, tin selenide nanostructures show great promise for applications in energy storage and photovoltaic devices. Despite the great progress that has been achieved, the phase-controlled synthesis of two-dimensional (2D) tin selenide nanostructures remains a challenge, and their use in supercapacitors has not been explored. In this paper, 2D tin selenide nanostructures, including pure SnSe2 nanodisks (NDs), mixed-phase SnSe-SnSe2 NDs, and pure SnSe nanosheets (NSs), have been synthesized by reacting SnCl2 and trioctylphosphine (TOP)-Se with borane-tert-butylamine complex (BTBC) and 1,3-dimethyl-3,4,5,6-tetrahydro-2(1H)-pyrimidinone. Utilizing the interplay of TOP and BTBC and changing only the amount of BTBC, the phase-controlled synthesis of 2D tin selenide nanostructures is realized for the first time. Phase-dependent pseudocapacitive behavior is observed for the resulting 2D nanostructures. The specific capacitances of pure SnSe2 NDs (168 F g(-1)) and SnSe NSs (228 F g(-1)) are much higher than those of other reported materials (e.g., graphene-Mn3O4 nanorods and TiN mesoporous spheres); thus, these tin selenide materials were used to fabricate flexible, all-solid-state supercapacitors. Devices fabricated with these two tin selenide materials exhibited high areal capacitances, good cycling stabilities, excellent flexibilities, and desirable mechanical stabilities, which were comparable to or better than those reported recently for other solid-state devices based on graphene and 3D GeSe2 nanostructures. Additionally, the rate capability of the SnSe2 NDs device was much better than that of the SnSe NS device, indicating that SnSe2 NDs are promising active materials for use in high-performance, flexible, all-solid-state supercapacitors.

Direct transparent electrode patterning on layered GaN substrate by screen printing of indium tin oxide nanoparticle ink for Eu-doped GaN red light-emitting diode

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kashiwagi, Y., E-mail: kasiwagi@omtri.or.jp; Yamamoto, M.; Saitoh, M.

2014-12-01

Transparent electrodes were formed on Eu-doped GaN-based red-light-emitting diode (GaN:Eu LED) substrates by the screen printing of indium tin oxide nanoparticle (ITO np) inks as a wet process. The ITO nps with a mean diameter of 25 nm were synthesized by the controlled thermolysis of a mixture of indium complexes and tin complexes. After the direct screen printing of ITO np inks on GaN:Eu LED substrates and sintering at 850 °C for 10 min under atmospheric conditions, the resistivity of the ITO film was 5.2 mΩ cm. The fabricated LED up to 3 mm square surface emitted red light when the on-voltage was exceeded.

Direct transparent electrode patterning on layered GaN substrate by screen printing of indium tin oxide nanoparticle ink for Eu-doped GaN red light-emitting diode

NASA Astrophysics Data System (ADS)

Kashiwagi, Y.; Koizumi, A.; Takemura, Y.; Furuta, S.; Yamamoto, M.; Saitoh, M.; Takahashi, M.; Ohno, T.; Fujiwara, Y.; Murahashi, K.; Ohtsuka, K.; Nakamoto, M.

2014-12-01

Transparent electrodes were formed on Eu-doped GaN-based red-light-emitting diode (GaN:Eu LED) substrates by the screen printing of indium tin oxide nanoparticle (ITO np) inks as a wet process. The ITO nps with a mean diameter of 25 nm were synthesized by the controlled thermolysis of a mixture of indium complexes and tin complexes. After the direct screen printing of ITO np inks on GaN:Eu LED substrates and sintering at 850 °C for 10 min under atmospheric conditions, the resistivity of the ITO film was 5.2 mΩ cm. The fabricated LED up to 3 mm square surface emitted red light when the on-voltage was exceeded.

TiN films fabricated by reactive gas pulse sputtering: A hybrid design of multilayered and compositionally graded structures

NASA Astrophysics Data System (ADS)

Yang, Jijun; Zhang, Feifei; Wan, Qiang; Lu, Chenyang; Peng, Mingjing; Liao, Jiali; Yang, Yuanyou; Wang, Lumin; Liu, Ning

2016-12-01

Reactive gas pulse (RGP) sputtering approach was used to prepare TiN thin films through periodically changing the N2/Ar gas flow ratio. The obtained RGPsbnd TiN film possessed a hybrid architecture containing compositionally graded and multilayered structures, composed of hcp Ti-phase and fcc TiN-phase sublayers. Meanwhile, the RGP-TiN film exhibited a composition-oscillation along the film thickness direction, where the Ti-phase sublayer had a compositional gradient and the TiN-phase retained a constant stoichiometric ratio of Ti:N ≈ 1. The film modulation ratio λ (the thicknesses ratio of the Ti and TiN-phase sublayer) can be effectively tuned by controlling the undulation behavior of the N2 partial flow rate. Detailed analysis showed that this hybrid structure originated from a periodic transition of the film growth mode during the reactive sputtering process.

TiN-Coating Effects on Stainless Steel Tribological Behavior Under Dry and Lubricated Conditions

NASA Astrophysics Data System (ADS)

Zhang, Liqiang; Yang, Huisheng; Pang, Xiaolu; Gao, Kewei; Tran, Hai T.; Volinsky, Alex A.

2014-04-01

The tribological properties of magnetron sputtered titanium nitride coating on 316L steel, sliding against Si3N4 ceramic ball under dry friction and synthetic perspiration lubrication, were investigated. The morphology of the worn surface and the elemental composition of the wear debris were examined by scanning electron microscopy and energy dispersive spectroscopy. TiN coatings and 316L stainless steel had better tribological properties under synthetic perspiration lubrication than under dry friction. Among the three tested materials (316L, 1.6 and 2.4 μm TiN coatings), 2.4 μm TiN coating exhibits the best wear resistance. The difference in wear damage of the three materials is essentially due to the wear mechanisms. For the TiN coating, the damage is attributed to abrasive wear under synthetic perspiration lubrication and the complex interactive mechanisms, including abrasive and adhesive wear, along with plastic deformation, under dry friction.

Co-precipitation synthesis of nano-composites consists of zinc and tin oxides coatings on glass with enhanced photocatalytic activity on degradation of Reactive Blue 160 KE2B.

PubMed

Habibi, Mohammad Hossein; Mardani, Maryam

2015-02-25

Nano-composite containing zinc oxide-tin oxide was obtained by a facile co-precipitation route using tin chloride tetrahydrate and zinc chloride as precursors and coated on glass by Doctor Blade deposition. The crystalline structure and morphology of composites were evaluated by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The XRD results showed peaks relative to zinc oxide with hexagonal wurtzite structure and tin oxide with tetragonal structure. FESEM observations showed that the nano-composite consisted of aggregates of particles with an average particle size of 18 nm. The photocatalytic activity of the pure SnO2, pure ZnO, ZnSnO3-Zn2SnO4 and ZnO-SnO2 nano-structure thin films was examined using the degradation of a textile dye Reactive Blue 160 (KE2B). ZnO-SnO2 nano-composite showed enhanced photo-catalytic activity than the pure zinc oxide and tin oxide. The enhanced photo-catalytic activity of the nano-composite was ascribed to an improved charge separation of the photo-generated electron-hole pairs. Copyright © 2014 Elsevier B.V. All rights reserved.

Atomic absorption spectrophotometric determination of tin in canned foods, using nitric acid-hydrochloric acid digestion and nitrous oxide-acetylene flame: collaborative study.

PubMed

Dabeka, R W; McKenzie, A D; Albert, R H

1985-01-01

Twenty-six collaborators participated in a study to evaluate an atomic absorption spectrophotometric (AAS) method for the determination of tin in canned foods. The 5 foods evaluated were meat, pineapple juice, tomato paste, evaporated milk, and green beans, each spiked at 2 levels. The concentration range of tin in the samples was 10-450 micrograms/g, and each level was sent as a blind duplicate. Statistical treatment of results revealed no laboratory outliers and 6 individual or replicate-total outliers, accounting for 3.3% of the data. Repeatability (within-laboratory) coefficient of variation (CVo) ranged from 2.2 to 48%, depending on the tin level and food evaluated. For samples containing greater than or equal to 80 micrograms/g of tin, repeatability CV averaged 5.6% including outliers and 3.7% after their rejection. Overall among-laboratories coefficient of variation (CVx) varied from 3.3 to 58%; at levels greater than or equal to 80 micrograms/g, it averaged 7.3% with outliers and 5.3% after their rejection. Recovery of tin, based on spiking levels, ranged from 100.0 to 112.8% and averaged 105.4%. Detection limit range is 2-10 micrograms/g, and lower quantitation limit is 40 micrograms/g. This method has been adopted official first action.

Aromatic Ring Currents Illustrated--NMR Spectra of Tin(IV) Porphyrin Complexes. An Advanced Undergraduate Experiment.

ERIC Educational Resources Information Center

Arnold, Dennis P.

1988-01-01

Attempts to show that in the closed loops of cyclic structures the protons situated in conic regions above and below the ring will be shielded. Uses the diamagnetic and air stable octahedral tin(IV) complexes of porphyrins for study. Notes complexes crystallize easily and offer spectacular purple colors. (MVL)

Drilling fluids and thinners therefor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allison, G.M. III

1986-10-21

This patent describes an aqueous drilling fluid comprising water, finely divided solids and a first agent and a second agent. The first agent comprises a sulfoalkylated tannin containing no complexing heavy metal. The second agent comprises at least one at least partly water-soluble metal compound comprising tin. The weight ratio of the first agent to the second agent is in the range from about 100;1 to about 1:1.

Structural characterization of a bridged 99Tc-Sn-dimethylglyoxime complex: implications for the chemistry of 99mTc-radiopharmaceuticals prepared by the Sn (II) reduction of pertechnetate.

PubMed Central

Deutsch, E; Elder, R C; Lange, B A; Vaal, M J; Lay, D G

1976-01-01

Reduction of pertechnetate by tin(II) in the presence of dimethylglyoxime is shown, by single crystal x-ray analysis, to yield a technetium-tin-dimethylglyoxime complex in which tin and technetium are intimately connected by a triple bridging arrangement. One bridge consists of a single oxygen atom and it is hypothesized that this bridge arises from the inner sphere reduction of technetium by tin(II), the electrons being transferred through a technetium "yl" oxygen which eventually becomes the bridging atom. Two additional bridges arise from two dimethylglyoxime ligands that function as bidentate nitrogen donors towards Tc and monodentate oxygen donors towards Sn. The tin atom can thus be viewed as providing a three-pronged "cap" on one end of the Tc-dimethylglyoxime complex. The additional coordination sites around Tc are occupied by the two nitrogens of a third dimethylglyoxime ligand, making the Tc seven-coordinate. The additional coordination sites around Sn are occupied by three chloride anions, giving the Sn a fac octahedral coordination environment. From indirect evidence the oxidation states of tin and technetium are tentatively assigned to be IV and V, respectively. Since most 99mTc-radiopharmaceuticals are synthesized by the tin(II) reduction of pertechnetate, it is likely that the Sn-O-Tc linkage described in this work is an important feature of the chemistry of these species. This linkage also provides a ready rationale for the close association of tin and technetium observed in many 99mTc-radiopharmaceuticals. PMID:1069984

Bouquet-Like Mn2SnO4 Nanocomposite Engineered with Graphene Sheets as an Advanced Lithium-Ion Battery Anode.

PubMed

Rehman, Wasif Ur; Xu, Youlong; Sun, Xiaofei; Ullah, Inam; Zhang, Yuan; Li, Long

2018-05-30

Volume expansion is a major challenge associated with tin oxide (SnO x ), which causes poor cyclability in lithium-ion battery anode. Bare tin dioxide (SnO 2 ), tin dioxide with graphene sheets (SnO 2 @GS), and bouquet-like nanocomposite structure (Mn 2 SnO 4 @GS) are prepared via hydrothermal method followed by annealing. The obtained composite material presents a bouquet structure containing manganese and tin oxide nanoparticle network with graphene sheets. Benefiting from this porous nanostructure, in which graphene sheets provide high electronic pathways to enhance the electronic conductivity, uniformly distributed particles offer accelerated kinetic reaction with lithium ion and reduced volume deviation in the tin dioxide (SnO 2 ) particle during charge-discharge testing. As a consequence, ternary composite Mn 2 SnO 4 @GS showed a high rate performance and outstanding cyclability of anode material for lithium-ion batteries. The electrode achieved a specific capacity of about 1070 mA h g -1 at a current density of 400 mA g -1 after 200 cycles; meanwhile, the electrode still delivered a specific capacity of about 455 mA h g -1 at a high current density of 2500 mA g -1 . Ternary Mn 2 SnO 4 @GS material could facilitate fabrication of unique structure and conductive network as advanced lithium-ion battery.

Calculating Equilibrium Constants in the SnCl2-H2O-NaOH System According to Potentiometric Titration Data

NASA Astrophysics Data System (ADS)

Maskaeva, L. N.; Fedorova, E. A.; Yusupov, R. A.; Markov, V. F.

2018-05-01

The potentiometric titration of tin chloride SnCl2 is performed in the concentration range of 0.00009-1.1 mol/L with a solution of sodium hydroxide NaOH. According to potentiometric titration data based on modeling equilibria in the SnCl2-H2O-NaOH system, basic equations are generated for the main processes, and instability constants are calculated for the resulting hydroxo complexes and equilibrium constants of low-soluble tin(II) compounds. The data will be of interest for specialists in the field of theory of solutions.

Facile Synthesis and Superior Catalytic Activity of Nano-TiN@N-C for Hydrogen Storage in NaAlH4.

PubMed

Zhang, Xin; Ren, Zhuanghe; Lu, Yunhao; Yao, Jianhua; Gao, Mingxia; Liu, Yongfeng; Pan, Hongge

2018-05-09

Herein, we synthesize successfully ultrafine TiN nanoparticles (<3 nm in size) embedded in N-doped carbon nanorods (nano-TiN@N-C) by a facile one-step calcination process. The prepared nano-TiN@N-C exhibits superior catalytic activity for hydrogen storage in NaAlH 4 . Adding 7 wt % nano-TiN@N-C induces more than 100 °C reduction in the onset dehydrogenation temperature of NaAlH 4 . Approximately 4.9 wt % H 2 is rapidly released from the 7 wt % nano-TiN@N-C-containing NaAlH 4 at 140 °C within 60 min, and the dehydrogenation product is completely hydrogenated at 100 °C within 15 min under 100 bar of hydrogen, exhibiting significantly improved desorption/absorption kinetics. No capacity loss is observed for the nano-TiN@N-C-containing sample within 25 de-/hydrogenation cycles because nano-TiN functions as an active catalyst instead of a precursor. A severe structural distortion with extended bond lengths and reduced bond strengths for Al-H bonding when the [AlH 4 ] - group adsorbs on the TiN cluster is demonstrated for the first time by density functional theory calculations, which well-explains the reduced de-/hydrogenation temperatures of the nano-TiN@N-C-containing NaAlH 4 . These findings provide new insights into designing and synthesizing high-performance catalysts for hydrogen storage in complex hydrides.

Metal and silicate particles including nanoparticles are present in electronic cigarette cartomizer fluid and aerosol.

PubMed

Williams, Monique; Villarreal, Amanda; Bozhilov, Krassimir; Lin, Sabrina; Talbot, Prue

2013-01-01

Electronic cigarettes (EC) deliver aerosol by heating fluid containing nicotine. Cartomizer EC combine the fluid chamber and heating element in a single unit. Because EC do not burn tobacco, they may be safer than conventional cigarettes. Their use is rapidly increasing worldwide with little prior testing of their aerosol. We tested the hypothesis that EC aerosol contains metals derived from various components in EC. Cartomizer contents and aerosols were analyzed using light and electron microscopy, cytotoxicity testing, x-ray microanalysis, particle counting, and inductively coupled plasma optical emission spectrometry. The filament, a nickel-chromium wire, was coupled to a thicker copper wire coated with silver. The silver coating was sometimes missing. Four tin solder joints attached the wires to each other and coupled the copper/silver wire to the air tube and mouthpiece. All cartomizers had evidence of use before packaging (burn spots on the fibers and electrophoretic movement of fluid in the fibers). Fibers in two cartomizers had green deposits that contained copper. Centrifugation of the fibers produced large pellets containing tin. Tin particles and tin whiskers were identified in cartridge fluid and outer fibers. Cartomizer fluid with tin particles was cytotoxic in assays using human pulmonary fibroblasts. The aerosol contained particles >1 µm comprised of tin, silver, iron, nickel, aluminum, and silicate and nanoparticles (<100 nm) of tin, chromium and nickel. The concentrations of nine of eleven elements in EC aerosol were higher than or equal to the corresponding concentrations in conventional cigarette smoke. Many of the elements identified in EC aerosol are known to cause respiratory distress and disease. The presence of metal and silicate particles in cartomizer aerosol demonstrates the need for improved quality control in EC design and manufacture and studies on how EC aerosol impacts the health of users and bystanders.

Synthesis of ligand-stabilized metal oxide nanocrystals and epitaxial core/shell nanocrystals via a lower-temperature esterification process.

PubMed

Ito, Daisuke; Yokoyama, Shun; Zaikova, Tatiana; Masuko, Keiichiro; Hutchison, James E

2014-01-28

The properties of metal oxide nanocrystals can be tuned by incorporating mixtures of matrix metal elements, adding metal ion dopants, or constructing core/shell structures. However, high-temperature conditions required to synthesize these nanocrystals make it difficult to achieve the desired compositions, doping levels, and structural control. We present a lower temperature synthesis of ligand-stabilized metal oxide nanocrystals that produces crystalline, monodisperse nanocrystals at temperatures well below the thermal decomposition point of the precursors. Slow injection (0.2 mL/min) of an oleic acid solution of the metal oleate complex into an oleyl alcohol solvent at 230 °C results in a rapid esterification reaction and the production of metal oxide nanocrystals. The approach produces high yields of crystalline, monodisperse metal oxide nanoparticles containing manganese, iron, cobalt, zinc, and indium within 20 min. Synthesis of tin-doped indium oxide (ITO) can be accomplished with good control of the tin doping levels. Finally, the method makes it possible to perform epitaxial growth of shells onto nanocrystal cores to produce core/shell nanocrystals.

A genome-wide approach identifies distinct but overlapping subsets of cellular mRNAs associated with Staufen1- and Staufen2-containing ribonucleoprotein complexes.

PubMed

Furic, Luc; Maher-Laporte, Marjolaine; DesGroseillers, Luc

2008-02-01

Messenger RNAs are associated with multiple RNA-binding proteins to form ribonucleoprotein (mRNP) complexes. These proteins are important regulators of the fate of their target mRNAs. In human cells, Staufen1 and Staufen2 proteins, coded by two different genes, are double-stranded RNA-binding proteins involved in several cellular functions including mRNA localization, translation, and decay. Although 51% identical, these proteins are nevertheless found in different RNA particles. In addition, differential splicing events generate Staufen2 isoforms that only differ at their N-terminal extremities. In this paper, we used a genome-wide approach to identify and compare the mRNA targets of mammalian Staufen proteins. The mRNA content of Staufen mRNPs was identified by probing DNA microarrays with probes derived from mRNAs isolated from immunopurified Staufen-containing complexes following transfection of HEK293T cells with Stau1(55)-HA, Stau2(59)-HA, or Stau2(62)-HA expressors. Our results indicate that 7% and 11% of the cellular RNAs expressed in HEK293T cells are found in Stau1- and in Stau2-containing mRNPs, respectively. A comparison of Stau1- and Stau2-containing mRNAs identifies a relatively low percentage of common mRNAs; the percentage of common mRNAs highly increases when mRNAs in Stau2(59)-HA- and Stau2(62)-containing mRNPs are compared. There is a predominance of mRNAs involved in cell metabolism, transport, transcription, regulation of cell processes, and catalytic activity. All these subsets of mRNAs are mostly distinct from those associated with FMRP or IMP, although some mRNAs overlap. Consistent with a model of post-transcriptional gene regulation, our results show that Stau1- and Stau2-mRNPs associate with distinct but overlapping sets of cellular mRNAs.

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

40 CFR 721.10297 - Tin, C16-18 and C18-unsatd. fatty acids castor-oil fatty acids complexes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Tin, C16-18 and C18-unsatd. fatty... SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.10297 Tin, C16-18 and C18-unsatd... to reporting. (1) The chemical substance identified as tin, C16-18 and C18-unsatd. fatty acids castor...

Deposition of conductive TiN shells on SiO2 nanoparticles with a fluidized bed ALD reactor

NASA Astrophysics Data System (ADS)

Didden, Arjen; Hillebrand, Philipp; Wollgarten, Markus; Dam, Bernard; van de Krol, Roel

2016-02-01

Conductive TiN shells have been deposited on SiO2 nanoparticles (10-20 nm primary particle size) with fluidized bed atomic layer deposition using TDMAT and NH3 as precursors. Analysis of the powders confirms that shell growth saturates at approximately 0.4 nm/cycle at TDMAT doses of >1.2 mmol/g of powder. TEM and XPS analysis showed that all particles were coated with homogeneous shells containing titanium. Due to the large specific surface area of the nanoparticles, the TiN shells rapidly oxidize upon exposure to air. Electrical measurements show that the partially oxidized shells are conducting, with apparent resistivity of approximately 11 kΩ cm. The resistivity of the powders is strongly influenced by the NH3 dose, with a smaller dose giving an order-of-magnitude higher resistivity.

The thermochromic behavior of aromatic amine-SO2 charge transfer complexes

NASA Astrophysics Data System (ADS)

Monezi, Natália M.; Borin, Antonio C.; Santos, Paulo S.; Ando, Rômulo A.

2017-02-01

The distinct thermochromism observed in solutions containing N,N-dimethylaniline (DMA) and N,N-diethylaniline (DEA) and SO2 was investigated by resonance Raman spectroscopy in a wide range of temperatures. The results indicate in addition to the charge transfer (CT) complexes DMA-SO2 and DEA-SO2, the presence of collision complexes involving the CT complexes and excess DMA and DEA molecules. The latter in fact is the chromophore responsible for the long wavelength absorption originating the color. The Raman signature of the collision complex was attributed to the distinct enhancement of a band at 1140 cm- 1 assigned to νs(SO2), in contrast to the same mode in the 1:1 complex at 1115 cm- 1. The intensity of such band, assigned to the collision complex is favored at high temperatures and depends on the steric hindrance associated to amines, as well as the SO2 molar fraction. Quantum chemical calculations based on time-dependent density functional theory (TDDFT) support the proposed interpretation.

A New Femtosecond Laser-Based Three-Dimensional Tomography Technique

NASA Astrophysics Data System (ADS)

Echlin, McLean P.

2011-12-01

Tomographic imaging has dramatically changed science, most notably in the fields of medicine and biology, by producing 3D views of structures which are too complex to understand in any other way. Current tomographic techniques require extensive time both for post-processing and data collection. Femtosecond laser based tomographic techniques have been developed in both standard atmosphere (femtosecond laser-based serial sectioning technique - FSLSS) and in vacuum (Tri-Beam System) for the fast collection (10 5mum3/s) of mm3 sized 3D datasets. Both techniques use femtosecond laser pulses to selectively remove layer-by-layer areas of material with low collateral damage and a negligible heat affected zone. To the authors knowledge, femtosecond lasers have never been used to serial section and these techniques have been entirely and uniquely developed by the author and his collaborators at the University of Michigan and University of California Santa Barbara. The FSLSS was applied to measure the 3D distribution of TiN particles in a 4330 steel. Single pulse ablation morphologies and rates were measured and collected from literature. Simultaneous two-phase ablation of TiN and steel matrix was shown to occur at fluences of 0.9-2 J/cm2. Laser scanning protocols were developed minimizing surface roughness to 0.1-0.4 mum for laser-based sectioning. The FSLSS technique was used to section and 3D reconstruct titanium nitride (TiN) containing 4330 steel. Statistical analysis of 3D TiN particle sizes, distribution parameters, and particle density were measured. A methodology was developed to use the 3D datasets to produce statistical volume elements (SVEs) for toughness modeling. Six FSLSS TiN datasets were sub-sampled into 48 SVEs for statistical analysis and toughness modeling using the Rice-Tracey and Garrison-Moody models. A two-parameter Weibull analysis was performed and variability in the toughness data agreed well with Ruggieri et al. bulk toughness measurements. The Tri-Beam system combines the benefits of laser based material removal (speed, low-damage, automated) with detectors that collect chemical, structural, and topological information. Multi-modal sectioning information was collected after many laser scanning passes demonstrating the capability of the Tri-Beam system.

THE USE OF GAMMA RADIATION TO DESTROY SALMONELLAE IN FROZEN WHOLE EGG

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brooks, J.; Hannan, R.S.; Hobbs, B.C.

Frozen whole egg (an intimate mixture of the white and yolk) is the most important egg product in international commerce. Average imports into the United Kingdom alone have amounted to about 22,000 tons per annum over the last ten years. It has been known for some time that egg products may contain members of the Salmonella group capable of causing food poisoning, but the position has been rendered more serious by the recent discovery of S. paratyphi B in egg products imported. In fact, the proved association of egg products with paratyphoid B fever has created a new situation inmore » the epidemiology of the disease. After treatment of small samples of frozen whole egg with 2-Mev cathode rays, it was concluded that a dose of about 300,000 to 500,000 rads would destroy the numbers of salmonellas normally encountered in the product without impairing the baking qualities of the material. Whole tins, each containing 22 pounds, were therefore irradiated in the frozen state with cobalt-80 gamma rays. Two tins were treated at each of three dose levels of 300,000, 400,000, and 500,000 rads. The contaminants present before irradiation were S. paratyphi B (three tins), S. newport (two tins), and S. thompson (one tin). No salmonellas were detected in duplicate samples of material taken from each of the tins after irradiation. If the effectiveness of the treatment is confirmed by further work, the process has obvious attractions since it dispenses with the need to thaw or otherwise to handle the product. (auth)« less

Ab Initio Study of the Atomic Level Structure of the Rutile TiO2(110)-Titanium Nitride (TiN) Interface.

PubMed

Gutiérrez Moreno, José Julio; Nolan, Michael

2017-11-01

Titanium nitride (TiN) is widely used in industry as a protective coating due to its hardness and resistance to corrosion and can spontaneously form a thin oxide layer when it is exposed to air, which could modify the properties of the coating. With limited understanding of the TiO 2 -TiN interfacial system at present, this work aims to describe the structural and electronic properties of oxidized TiN based on a density functional theory (DFT) study of the rutile TiO 2 (110)-TiN(100) interface model system, also including Hubbard +U correction on Ti 3d states. The small lattice mismatch gives a good stability to the TiO 2 -TiN interface after depositing the oxide onto TiN through the formation of interfacial Ti-O bonds. Our DFT+U study shows the presence of Ti 3+ cations in the TiO 2 region, which are preferentially located next to the interface region as well as the rotation of the rutile TiO 2 octahedra in the interface structure. The DFT+U TiO 2 electronic density of states (EDOS) shows localized Ti 3+ defect states forming in the midgap between the top edge of the valence and the bottom of the conduction band. We increase the complexity of our models by the introduction of nonstoichiometric compositions. Although the vacancy formation energies for Ti in TiN (E vac (Ti) ≥ 4.03 eV) or O in the oxide (E vac (O) ≥ 3.40 eV) are quite high relative to perfect TiO 2 -TiN, defects are known to form during the oxide growth and can therefore be present after TiO 2 formation. Our results show that a structure with exchanged O and N can lie 0.82 eV higher in energy than the perfect system, suggesting the stability of structures with interdiffused O and N anions at ambient conditions. The presence of N in TiO 2 introduces N 2p states localized between the top edge of the O 2p valence states and the midgap Ti 3+ 3d states, thus reducing the band gap in the TiO 2 region for the exchanged O/N interface EDOS. The outcomes of these simulations give us a most comprehensive insight on the atomic level structure and the electronic properties of oxidized TiN surfaces.

Study of tin amalgam mirrors by 1 1 9 Sn Mössbauer spectroscopy and other analytical methods

NASA Astrophysics Data System (ADS)

Lerf, A.; Wagner, F. E.; Herrera, L. K.; Justo, A.; Mu noz-Páez, A.; Pérez-Rodríguez, J. L.

2016-12-01

From the beginning of the 16 th until the end of the 19 th century the most widely used mirrors consisted of a pane of glass backed with a reflecting layer of tin-mercury amalgam. They were made by sliding the glass pane over a tin foil covered with liquid mercury. After removal of the superfluous mercury, tin amalgam formed slowly at ambient temperature and yielded a reflecting layer adhering to the surface of the glass. Such mirrors often deteriorate in the course of time by oxidation of the tin in the amalgam to stannous or stannic oxide. 119Sn Mössbauer spectroscopy, scanning electron microscopy, micro-XRF and X-ray diffraction have been used to study this deterioration process. The studied specimens were a modern mirror made for the reconstruction of the Green Vault in Dresden in the early 2000s, two rather well preserved German mirrors from the 17 th and 19 th centuries and several strongly deteriorated specimens of Baroque mirrors from the south of Spain. The modern mirror consists mainly of a Sn0.9Hg0.1 amalgam with only 2 % of SnO2. The older German mirrors showed more pronounced oxidation, containing 12 and 15 % of SnO2, which did not noticeably impair their reflectivity. In the samples from the Spanish mirrors at best a few percent of metallic phase was left. The majority of the tin had oxidised to SnO2, but between 8 and 20 % of the tin was present as SnO. X-ray diffraction yielded similar results and micro-XRF mapping using synchrotron radiation for excitation gave information on the distribution of Sn and Hg in the reflecting layer of the mirrors.

Platinum/Tin Oxide/Silica Gel Catalyst Oxidizes CO

NASA Technical Reports Server (NTRS)

Upchurch, Billy T.; Davis, Patricia P.; Schryer, David R.; Miller, Irvin M.; Brown, David; Van Norman, John D.; Brown, Kenneth G.

1991-01-01

Heterogeneous catalyst of platinum, tin oxide, and silica gel combines small concentrations of laser dissociation products, CO and O2, to form CO22 during long times at ambient temperature. Developed as means to prevent accumulation of these products in sealed CO2 lasers. Effective at ambient operating temperatures and installs directly in laser envelope. Formulated to have very high surface area and to chemisorb controlled quantities of moisture: chemisorbed water contained within and upon its structure, makes it highly active and very longlived so only small quantity needed for long times.

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2012 CFR

2012-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2011 CFR

2011-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2014 CFR

2014-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2013 CFR

2013-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

21 CFR 73.1646 - Bronze powder.

Code of Federal Regulations, 2010 CFR

2010-04-01

... electrolytic copper and zinc with small amounts of the virgin metals aluminum and tin. It contains small... part per million Aluminum (as Al), not more than 0.5 percent. Tin (as Sn), not more than 0.5 percent... percent. Maximum particle size 45µ (95 percent minimum). Aluminum, zinc, tin, and copper content shall be...

Enhancement of room temperature ferromagnetism in tin oxide nanocrystal using organic solvents

NASA Astrophysics Data System (ADS)

Sakthiraj, K.; Hema, M.; Balachandra Kumar, K.

2017-10-01

The effect of organic solvents (ethanol & ethylene glycol) on the room temperature ferromagnetism in nanocrystalline tin oxide has been studied. The samples were synthesized using sol-gel method with the mixture of water & organic liquid as solvent. It is found that pristine SnO2 nanocrystal contain two different types of paramagnetic centres over their surface:(i) surface chemisorbed oxygen species and (ii) Sn interstitial & oxygen vacancy defect pair. The magnetic moment induced in the as-prepared samples is mainly contributed by the alignment of local spin moments resulting from these defects. These surface defect states are highly activated by the usage of ethylene glycol solvent rather than ethylene in tin oxide nanostructure synthesis. Powder X-ray diffraction, transmission electron microscope imaging, energy dispersive spectrometry, Fourier transformed infrared spectroscopy, UV-vis absorption spectroscopy, photoluminescence spectroscopy, vibrating sample magnetometer measurement and electron spin resonance spectroscopy were employed to characterize the nanostructured tin oxide materials.

NASA GSFC Tin Whisker Homepage http://nepp.nasa.gov/whisker

NASA Technical Reports Server (NTRS)

Shaw, Harry

2000-01-01

The NASA GSFC Tin Whisker Homepage provides general information and GSFC Code 562 experimentation results regarding the well known phenomenon of tin whisker formation from pure tin plated substrates. The objective of this www site is to provide a central repository for information pertaining to this phenomenon and to provide status of the GSFC experiments to understand the behavior of tin whiskers in space environments. The Tin Whisker www site is produced by Code 562. This www site does not provide information pertaining to patented or proprietary information. All of the information contained in this www site is at the level of that produced by industry and university researchers and is published at international conferences.

A simple, rapid and green ultrasound assisted and ionic liquid dispersive microextraction procedure for the determination of tin in foods employing ETAAS.

PubMed

Tuzen, Mustafa; Uluozlu, Ozgur Dogan; Mendil, Durali; Soylak, Mustafa; Machado, Luana O R; Dos Santos, Walter N L; Ferreira, Sergio L C

2018-04-15

This paper proposes a simple, rapid and green ultrasound assisted and ionic liquid dispersive microextraction procedure using pyrocatechol violet (PV) as complexing reagent and 1-hexyl-3-methylimidazolium bis(trifluoromethylsulfonyl)-imide [C 6 MIM][Tf 2 N] as ionic liquid for the detection of tin employing electrothermal atomic absorption spectrometry (ETAAS). The optimization step was performed using a two-level full factorial design involving the following factors: pH of the working media, amount reagents, ionic liquid volume and extraction time and the chemometric response was tin recovery. The procedure allowed the determination of tin with limits of detection and quantification of 3.4 and 11.3 ng L -1 , respectively. The relative standard deviation was 4.5% for a tin solution of 0.50 µg L -1 . The validation method was confirmed by analysis of rice flour certified reference material. The method was applied for the quantification of tin in several food samples. The concentration range found varied from 0.10 to 1.50 µg g -1 . Copyright © 2017 Elsevier Ltd. All rights reserved.

Subunits of ADA-two-A-containing (ATAC) or Spt-Ada-Gcn5-acetyltrasferase (SAGA) Coactivator Complexes Enhance the Acetyltransferase Activity of GCN5.

PubMed

Riss, Anne; Scheer, Elisabeth; Joint, Mathilde; Trowitzsch, Simon; Berger, Imre; Tora, László

2015-11-27

Histone acetyl transferases (HATs) play a crucial role in eukaryotes by regulating chromatin architecture and locus specific transcription. GCN5 (KAT2A) is a member of the GNAT (Gcn5-related N-acetyltransferase) family of HATs. In metazoans this enzyme is found in two functionally distinct coactivator complexes, SAGA (Spt Ada Gcn5 acetyltransferase) and ATAC (Ada Two A-containing). These two multiprotein complexes comprise complex-specific and shared subunits, which are organized in functional modules. The HAT module of ATAC is composed of GCN5, ADA2a, ADA3, and SGF29, whereas in the SAGA HAT module ADA2b is present instead of ADA2a. To better understand how the activity of human (h) hGCN5 is regulated in the two related, but different, HAT complexes we carried out in vitro HAT assays. We compared the activity of hGCN5 alone with its activity when it was part of purified recombinant hATAC or hSAGA HAT modules or endogenous hATAC or hSAGA complexes using histone tail peptides and full-length histones as substrates. We demonstrated that the subunit environment of the HAT complexes into which GCN5 incorporates determines the enhancement of GCN5 activity. On histone peptides we show that all the tested GCN5-containing complexes acetylate mainly histone H3K14. Our results suggest a stronger influence of ADA2b as compared with ADA2a on the activity of GCN5. However, the lysine acetylation specificity of GCN5 on histone tails or full-length histones was not changed when incorporated in the HAT modules of ATAC or SAGA complexes. Our results thus demonstrate that the catalytic activity of GCN5 is stimulated by subunits of the ADA2a- or ADA2b-containing HAT modules and is further increased by incorporation of the distinct HAT modules in the ATAC or SAGA holo-complexes. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

26 CFR 301.6723-1 - Failure to comply with other information reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... that a person— (A) Include his or her taxpayer identification number (“TIN”) on any return, statement... another person the TIN of such person, or (C) Furnish his or her TIN to another person; (iii) Any requirement contained in the regulations under section 215 that a person— (A) Furnish his or her TIN to...

26 CFR 301.6723-1 - Failure to comply with other information reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... that a person— (A) Include his or her taxpayer identification number (“TIN”) on any return, statement... another person the TIN of such person, or (C) Furnish his or her TIN to another person; (iii) Any requirement contained in the regulations under section 215 that a person— (A) Furnish his or her TIN to...

26 CFR 301.6723-1 - Failure to comply with other information reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... that a person— (A) Include his or her taxpayer identification number (“TIN”) on any return, statement... another person the TIN of such person, or (C) Furnish his or her TIN to another person; (iii) Any requirement contained in the regulations under section 215 that a person— (A) Furnish his or her TIN to...

78 FR 27476 - Pirelli Tire LLC, Grant of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-10

... complete or partial tire identification number (TIN) on the inner tire sidewall as required by paragraphs... being modified or have been modified to ensure that the appropriate TIN information is contained on both... visibility of the full TIN on the outboard sidewall: Pirelli's internal policy allows dealers to sell these...

26 CFR 301.6723-1 - Failure to comply with other information reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... that a person— (A) Include his or her taxpayer identification number (“TIN”) on any return, statement... another person the TIN of such person, or (C) Furnish his or her TIN to another person; (iii) Any requirement contained in the regulations under section 215 that a person— (A) Furnish his or her TIN to...

26 CFR 301.6723-1 - Failure to comply with other information reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... that a person— (A) Include his or her taxpayer identification number (“TIN”) on any return, statement... another person the TIN of such person, or (C) Furnish his or her TIN to another person; (iii) Any requirement contained in the regulations under section 215 that a person— (A) Furnish his or her TIN to...

A genome-wide approach identifies distinct but overlapping subsets of cellular mRNAs associated with Staufen1- and Staufen2-containing ribonucleoprotein complexes

PubMed Central

Furic, Luc; Maher-Laporte, Marjolaine; DesGroseillers, Luc

2008-01-01

Messenger RNAs are associated with multiple RNA-binding proteins to form ribonucleoprotein (mRNP) complexes. These proteins are important regulators of the fate of their target mRNAs. In human cells, Staufen1 and Staufen2 proteins, coded by two different genes, are double-stranded RNA-binding proteins involved in several cellular functions including mRNA localization, translation, and decay. Although 51% identical, these proteins are nevertheless found in different RNA particles. In addition, differential splicing events generate Staufen2 isoforms that only differ at their N-terminal extremities. In this paper, we used a genome-wide approach to identify and compare the mRNA targets of mammalian Staufen proteins. The mRNA content of Staufen mRNPs was identified by probing DNA microarrays with probes derived from mRNAs isolated from immunopurified Staufen-containing complexes following transfection of HEK293T cells with Stau155-HA, Stau259-HA, or Stau262-HA expressors. Our results indicate that 7% and 11% of the cellular RNAs expressed in HEK293T cells are found in Stau1- and in Stau2-containing mRNPs, respectively. A comparison of Stau1- and Stau2-containing mRNAs identifies a relatively low percentage of common mRNAs; the percentage of common mRNAs highly increases when mRNAs in Stau259-HA- and Stau262-containing mRNPs are compared. There is a predominance of mRNAs involved in cell metabolism, transport, transcription, regulation of cell processes, and catalytic activity. All these subsets of mRNAs are mostly distinct from those associated with FMRP or IMP, although some mRNAs overlap. Consistent with a model of post-transcriptionnal gene regulation, our results show that Stau1- and Stau2-mRNPs associate with distinct but overlapping sets of cellular mRNAs. PMID:18094122

International strategic minerals inventory summary report; tin

USGS Publications Warehouse

Sutphin, D.M.; Sabin, A.E.; Reed, B.L.

1990-01-01

The International Strategic Minerals Inventory tin inventory contains records for 56 major tin deposits and districts in 21 countries. These countries accounted for 98 percent of the 10 million metric tons of tin produced in the period 1934-87. Tin is a good alloying metal and is generally nontoxic, and its chief uses are as tinplate for tin cans and as solder in electronics. The 56 locations consist of 39 lode deposits and 17 placers and contain almost 7.5 million metric tons of tin in identified economic resources (R1E) and another 1.5 million metric tons of tin in other resource categories. Most of these resources are in major deposits that have been known for over a hundred years. Lode deposits account for 44 percent of the R1E and 87 percent of the resources in other categories. Placer deposits make up the remainder. Low-income and middle-income countries, including Bolivia and Brazil and countries along the Southeast Asian Tin Belt such as Malaysia, Thailand, and Indonesia account for 91 percent of the R1E resources of tin and for 61 percent of resources in other categories. The United States has less than 0.05 percent of the world's tin R1E in major deposits. Available data suggest that the Soviet Union may have about 4 percent of resources in this category. The industrial market economy countries of the United States, Japan, Federal Republic of Germany, and the United Kingdom are major consumers of tin, whereas the major tin-producing countries generally consume little tin. The Soviet Union and China are both major producers and consumers of tin. At the end of World War II, the four largest tin-producing countries (Bolivia, the Belgian Congo (Zaire), Nigeria, and Malaysia) produced over 80 percent of the world's tin. In 1986, the portion of production from the four largest producers (Malaysia, Brazil, Soviet Union, Indonesia) declined to about 55 percent, while the price of tin rose from about $1,500 to $18,000 per metric ton. In response to tin shortages during World War II, the United States began stockpiling refined tin metal from approximately 1946 to 1953 to ensure a strategic supply in the event of another war. Since World War II, there have been six International Tin Agreements to maintain price and supply stability between tin producers and consumers. Artificially high prices set by the tin-producing members and a tin glut brought on by independent producers like Brazil caused the collapse of the world tin market in late 1985; the International Tin Council exhausted its credit to support the market price. By the year 2025, Bolivia's underground lode mines will likely have insignificant production, as will those in the United Kingdom. Tin mines in the Southeast Asian Tin Belt will still be active. Brazil, which has risen from the eighth-ranked tin-producing country in 1982 to the largest producer in 1988, will likely be a major influence on world tin production well into the 21st century. The future mining activity of deposits presently inactive in Australia is impossible to predict.

Formation of hydrothermal tin deposits: Raman spectroscopic evidence for an important role of aqueous Sn(IV) species

NASA Astrophysics Data System (ADS)

Schmidt, Christian

2018-01-01

The speciation of tin and the solubility of cassiterite in H2O + HCl were determined at temperatures to 600 °C using in situ Raman spectroscopy. In addition, information on the fluid-melt partition of Sn was obtained at 700 °C and indicated a preference of the fluid only at HCl concentrations that are much higher than in fluids exsolved from natural felsic melts. Dissolution of cassiterite generally resulted in formation of Sn(IV) species unless reduced conditions were generated by hydrogen permeation or carbohydrates in the starting material. The prevalent aqueous Sn(IV) species was [SnCl4(H2O)2]0, with additional [SnCl3(H2O)3]+ and [SnCl5(H2O)]-. The only detectable Sn(II) species was very likely [Sn(II)Cl3]-. Cassiterite solubility increased with HCl concentration and was generally high in H2O+HCl fluids, with no strong dependencies on temperature, pressure, or the oxidation state of tin in the fluid. The Sn(IV) concentrations at 500 and 600 °C determined from the integrated ν1[Sn(IV)sbnd Cl] band intensity are in good agreement with literature data on the cassiterite solubility in H2O + HCl at oxygen fugacities along the hematite-magnetite buffer. The combined results from previous experimental studies and this study demonstrate that HCl molality is a crucial parameter for hydrothermal mobilization and transport of tin and for cassiterite precipitation, and that pH, pressure and temperature are less important. Current models on hydrothermal tin deposit formation need to be augmented to include Sn(IV)sbnd Cl complexes as significant tin-transporting species. Irrespective of the oxidation state of tin in the fluid, cassiterite precipitates due to reaction of the hydrothermal fluid with the wall rock (greisen or skarn formation), dilution (mixing with meteoric water) or a decrease in the HCl activity in the aqueous liquid by boiling. A redox reaction is only required for tin transported as Sn(II) to be converted to Sn(IV).

Tin resources of Brazil

USGS Publications Warehouse

White, Max Gregg

1974-01-01

Annual tin production in Brazil, most of it from cassiterite placer deposits in Rondonia Territory, amounts to about 4,000 metric tons (4,400 short tons) of concentrate containing 66 percent tin, much of which is consumed by Brazilian industry. Reserves of cassiterite concentrate in the placers of Rondonia district are estimated at about 160,000 (176,000 short tons) containing 66 percent tin. Extensive undiscovered resources of cassiterite possibly exist in southern Rondonia Territory and to the east of the Territory in northern Mato Grosso, southern Amazonas, and southern Para. Numerous occurrences have been reported in these regions and as far to the east as the headwaters of the Tapajos and the Xingo Rivers. Minor deposits or occurrences of cassiterite (or lode deposits about which there is only minimal information available) are located in Para, Amapa, Paraiba, Rio Grande do Norte, Ceara, Bahia, Minas Gerais, Goias, Sao Paulo, and Rio Grande do Sul. All the lode tin deposits are dated or enclosed in rocks that date as Precambrian B (900 to 1,300 m.y.).

IRRADIATION OF EGGS AND EGG PRODUCTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brooks, J.; Hannan, R.S.; Hobbs, B.C.

It has been known for some time that egg products may contain members of the Salmonella group capable of causing food poisoning, and the position has been rendered more serious by the recent discovery of S. paratyphi B in some of the samples of egg products. Attempts to destroy salmonellae in liquid egg by pasteurization before freezing or drying have met with considerable success but the process requires careful control. The tins in which the frozen product is distributed hold up to 20 kg, and are therefore of a size suitable for treatment with gamma -radiation. After treatment of smallmore » samples of frozen whole egg with 2 Mev cathode rays it was concluded that a dose of about O.3 to 0.5 Mrad would destroy the numbers of salmonellae normally encountered in the product without impairing the baking qualities of the material. Whole tins, each containing 10 kg of infected material, were therefore irradiated in the frozen state with Co/sup 60/ gamma -rays. Two tins were treated at each of three dose levels of 0.3, 0.4, and 0.5 Mrad. No salmonellae were detected in duplicate samples of 25 g of material taken from each of the tins after irradiation. If the effectiveness of the treatment is confirmed, the process has obvious attractions since it dispenses with the need to thaw or otherwise to handle the product. The paper also contains a general discussion on the irradiation of eggs and egg products. (auth)« less

Synthesis, Characterization and Antifertility Activity of New Unsymmetrical Macrocyclic Complexes of Tin(II)

PubMed Central

Sharma, Kripa; Joshi, S. C.

2000-01-01

A new series of unsymmetrical macrocyclic complexes of tin(ll) has been prepared by the template process using bis(3-oxo-2-butylidene)propane-1,3-diamine as precursor. This affords a method to synthesize these complexes with various ring sizes. The tetradentate macrocyclic precursor [N4mL] reacts with SnCl2 and different diamines in a 1:1:1 molar ratio in refluxing methanol to give complexes of the type [Sn(N4mL)Cl2]. The ring expansion has been achieved by varying the diamine between the two diacetyl amino nitrogen atoms. The macrocyclic precursor and its metal complexes have been characterized on the basis of elemental analysis, molar conductance, molecular weight determinations, IR, 1H NMR,13C NMR, 119Sn NMR and electronic spectral studies. An octahedral geometry around the metal ion is suggested for these complexes. On the basis of molecular weights and conductivity measurements, their monomeric and non-electrolytic nature has been confirmed. The precursor and complexes have been screened in vitro against a number of pathogenic fungi and bacteria to assess their growth inhibiting potential. The testicular sperm density and testicular sperm morphology, sperm motility, density of cauda epididymal spermatozoa and fertility in mating trails and biochemicals parameters of reproductive organs have been examined and discussed. PMID:18475951

Different Functions of Phylogenetically Distinct Bacterial Complex I Isozymes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spero, Melanie A.; Brickner, Joshua R.; Mollet, Jordan T.

NADH:quinone oxidoreductase (complex I) is a bioenergetic enzyme that transfers electrons from NADH to quinone, conserving the energy of this reaction by contributing to the proton motive force. While the importance of NADH oxidation to mitochondrial aerobic respiration is well documented, the contribution of complex I to bacterial electron transport chains has been tested in only a few species. Here, we analyze the function of two phylogenetically distinct complex I isozymes in Rhodobacter sphaeroides, an alphaproteobacterium that contains well-characterized electron transport chains. We found that R. sphaeroides complex I activity is important for aerobic respiration and required for anaerobic dimethylmore » sulfoxide (DMSO) respiration (in the absence of light), photoautotrophic growth, and photoheterotrophic growth (in the absence of an external electron acceptor). Our data also provide insight into the functions of the phylogenetically distinct R. sphaeroides complex I enzymes (complex I A and complex I E) in maintaining a cellular redox state during photoheterotrophic growth. We propose that the function of each isozyme during photoheterotrophic growth is either NADH synthesis (complex I A) or NADH oxidation (complex I E). The canonical alphaproteobacterial complex I isozyme (complex I A) was also shown to be important for routing electrons to nitrogenase-mediated H 2 production, while the horizontally acquired enzyme (complex I E) was dispensable in this process. Unlike the singular role of complex I in mitochondria, we predict that the phylogenetically distinct complex I enzymes found across bacterial species have evolved to enhance the functions of their respective electron transport chains. Cells use a proton motive force (PMF), NADH, and ATP to support numerous processes. In mitochondria, complex I uses NADH oxidation to generate a PMF, which can drive ATP synthesis. This study analyzed the function of complex I in bacteria, which contain more-diverse and more-flexible electron transport chains than mitochondria. We tested complex I function in Rhodobacter sphaeroides, a bacterium predicted to encode two phylogenetically distinct complex I isozymes. R. sphaeroides cells lacking both isozymes had growth defects during all tested modes of growth, illustrating the important function of this enzyme under diverse conditions. We conclude that the two isozymes are not functionally redundant and predict that phylogenetically distinct complex I enzymes have evolved to support the diverse lifestyles of bacteria.« less

Different Functions of Phylogenetically Distinct Bacterial Complex I Isozymes

DOE PAGES

Spero, Melanie A.; Brickner, Joshua R.; Mollet, Jordan T.; ...

2016-02-01

NADH:quinone oxidoreductase (complex I) is a bioenergetic enzyme that transfers electrons from NADH to quinone, conserving the energy of this reaction by contributing to the proton motive force. While the importance of NADH oxidation to mitochondrial aerobic respiration is well documented, the contribution of complex I to bacterial electron transport chains has been tested in only a few species. Here, we analyze the function of two phylogenetically distinct complex I isozymes in Rhodobacter sphaeroides, an alphaproteobacterium that contains well-characterized electron transport chains. We found that R. sphaeroides complex I activity is important for aerobic respiration and required for anaerobic dimethylmore » sulfoxide (DMSO) respiration (in the absence of light), photoautotrophic growth, and photoheterotrophic growth (in the absence of an external electron acceptor). Our data also provide insight into the functions of the phylogenetically distinct R. sphaeroides complex I enzymes (complex I A and complex I E) in maintaining a cellular redox state during photoheterotrophic growth. We propose that the function of each isozyme during photoheterotrophic growth is either NADH synthesis (complex I A) or NADH oxidation (complex I E). The canonical alphaproteobacterial complex I isozyme (complex I A) was also shown to be important for routing electrons to nitrogenase-mediated H 2 production, while the horizontally acquired enzyme (complex I E) was dispensable in this process. Unlike the singular role of complex I in mitochondria, we predict that the phylogenetically distinct complex I enzymes found across bacterial species have evolved to enhance the functions of their respective electron transport chains. Cells use a proton motive force (PMF), NADH, and ATP to support numerous processes. In mitochondria, complex I uses NADH oxidation to generate a PMF, which can drive ATP synthesis. This study analyzed the function of complex I in bacteria, which contain more-diverse and more-flexible electron transport chains than mitochondria. We tested complex I function in Rhodobacter sphaeroides, a bacterium predicted to encode two phylogenetically distinct complex I isozymes. R. sphaeroides cells lacking both isozymes had growth defects during all tested modes of growth, illustrating the important function of this enzyme under diverse conditions. We conclude that the two isozymes are not functionally redundant and predict that phylogenetically distinct complex I enzymes have evolved to support the diverse lifestyles of bacteria.« less

Liquid chromatography-hydride generation-atomic absorption spectrometry for the speciation of tin in seafoods.

PubMed

Viñas, Pilar; López-García, Ignacio; Merino-Meroño, Beatriz; Campillo, Natalia; Hernández-Cordóba, Manuel

2004-04-01

Liquid chromatography with hydride generation atomic absorption spectrometry as the detection system was applied to the separation and determination of inorganic tin, tributyltin, dibutyltin, monobutyltin, diphenyltin and monophenyltin. A reversed phase C18 column and a methanol/water/acetic acid (70:27:3, v/v/v) mixture containing 0.05%(v/v) triethylamine and 0.1%(w/v) tropolone as the mobile phase (isocratic elution) were used. Extraction of organotins from the samples was carried out using methanol containing 0.05%(w/v) tropolone, a process that was repeated twice. The supernatants were shaken with water and dichloromethane in a separating funnel and the organic phase was collected and evaporated to dryness. When the method was applied to the speciation of tin in fresh and canned mussels, no organotins above the detection limits were identified in any of the samples, inorganic tin being the only species detected. The reliability of the procedure was checked by analyzing the total tin content of the samples by electrothermal atomic absorption spectrometry and by speciation of tin in a certified reference material, mussel tissue (CRM 477). The method can be used for environmental monitoring of organotins contaminated samples.

The oxidation of carbon monoxide using tin oxide based catalysts

NASA Technical Reports Server (NTRS)

Sampson, Christopher F.; Jorgensen, Norman

1990-01-01

The preparation conditions for precious metal/tin oxide catalysts were optimized for maximum carbon monoxide/oxygen recombination efficiency. This was achieved by controlling the tin digestion, the peptization to form the sol, the calcination process and the method of adding the precious metals. Extensive studies of the tin oxide structure were carried out over the temperature range 20 to 500 C in air or hydrogen environments using Raman scattering and X ray diffraction. Adsorbed species on tin oxide, generated in an environment containing carbon monoxide, gave rise to a Raman band at about 1600 cm(exp -1) which was assigned to carbonaceous groups, possible carbonate.

49 CFR 178.33-5 - Material.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Containers, and Linings § 178.33-5 Material. (a) Uniform quality steel plate such as black plate, electro-tin plate, hot dipped tin plate, tern plate or other commercially accepted can making plate; or nonferrous...

49 CFR 178.33-5 - Material.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Containers, and Linings § 178.33-5 Material. (a) Uniform quality steel plate such as black plate, electro-tin plate, hot dipped tin plate, tern plate or other commercially accepted can making plate; or nonferrous...

49 CFR 178.33-5 - Material.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Containers, and Linings § 178.33-5 Material. (a) Uniform quality steel plate such as black plate, electro-tin plate, hot dipped tin plate, tern plate or other commercially accepted can making plate; or nonferrous...

49 CFR 178.33-5 - Material.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Containers, and Linings § 178.33-5 Material. (a) Uniform quality steel plate such as black plate, electro-tin plate, hot dipped tin plate, tern plate or other commercially accepted can making plate; or nonferrous...

Bayesian Cherry Picking Revisited

NASA Astrophysics Data System (ADS)

Garrett, Anthony J. M.; Prozesky, Victor M.; Padayachee, J.

2004-04-01

Tins are marketed as containing nine cherries. To fill the tins, cherries are fed into a drum containing twelve holes through which air is sucked; either zero, one or two cherries stick in each hole. Dielectric measurements are then made on each hole. Three outcomes are distinguished: empty hole (which is reliable); one cherry (which indicates one cherry with high probability, or two cherries with a complementary low probability known from calibration); or an uncertain number (which also indicates one cherry or two, with known probabilities that are quite similar). A choice can be made from which holes simultaneously to discharge contents into the tin. The sum and product rules of probability are applied in a Bayesian manner to find the distribution for the number of cherries in the tin. Based on this distribution, ways are discussed to optimise the number to nine cherries.

LIQUID METAL COMPOSITIONS CONTAINING URANIUM

DOEpatents

Teitel, R.J.

1959-04-21

Liquid metal compositions containing a solid uranium compound dispersed therein is described. Uranium combines with tin to form the intermetallic compound USn/sub 3/. It has been found that this compound may be incorporated into a liquid bath containing bismuth and lead-bismuth components, if a relatively small percentage of tin is also included in the bath. The composition has a low thermal neutron cross section which makes it suitable for use in a liquid metal fueled nuclear reactor.

Fluid inclusion characteristics and geological significance of the Dajinshan W-Sn polymetallic deposit in Yunfu, Guangdong Province

NASA Astrophysics Data System (ADS)

Yu, Zhangfa; Chen, Maohong; Zhao, Haijie

2015-05-01

The Dajinshan tungsten-tin polymetallic deposit is a quartz-vein-type ore deposit located in Western Guangdong Province. The ore bodies show a fairly simple shape and mainly occur as tungsten-tin polymetallic-bearing sulfide quartz veins, including quartz vein, quartz-greisens, and sulfide quartz veins, and their distribution is spatially related to Dajinshan granitoids. The formation of the deposit experienced three stages: a wolframite-molybdenite-quartz stage, a wolframite-cassiterite-sulfide-quartz stage, and a fluorite-calcite-carbonate stage. Based on detailed petrographic observations, we conducted microthermometric and Raman microspectroscopic studies of fluid inclusions formed at different ore-forming stages in the Dajinshan tungsten-tin polymetallic deposit, identifying four dominant types of fluid inclusions: aqueous two-phase inclusions, CO2-bearing inclusions, solid or daughter mineral-bearing inclusions, and gas-rich inclusions. The gas compositions of ore-forming fluids in the Dajinshan tungsten-tin polymetallic deposit are mostly CO2, CH4, and H2O. The hydrogen, oxygen, and sulfur isotopic data imply that the ore-forming fluids in the Dajinshan tungsten-tin polymetallic deposit were mainly derived from magmatic fluids, mixed with meteoric water in the ore-formation process. These results indicate that the fluid mixing and boiling led to the decomposition of the metal complex in ore-forming fluids and ore deposition.

Transcription instability in high-risk neuroblastoma is associated with a global perturbation of chromatin domains.

PubMed

Zanon, Carlo; Tonini, Gian Paolo

2017-11-01

Chromosome instability has a pivotal role among the hallmarks of cancer, but its transcriptional counterpart is rarely considered a relevant factor in cell destabilization. To examine transcription instability (TIN), we first devised a metric we named TIN index and used it to evaluate TIN on a dataset containing more than 500 neuroblastoma samples. We found that metastatic tumors from high-risk (HR) patients are characterized by significantly different TIN index values compared to low/intermediate-risk patients. Our results indicate that the TIN index is a good predictor of neuroblastoma patient's outcome, and a related TIN index gene signature (TIN-signature) is also able to predict the neuroblastoma patient's outcome with high confidence. Interestingly, we find that TIN-signature genes have a strong positional association with superenhancers in neuroblastoma tumors. Finally, we show that TIN is linked to chromatin structural domains and interferes with their integrity in HR neuroblastoma patients. This novel approach to gene expression analysis broadens the perspective of genome instability investigations to include functional aspects. © 2017 The Authors. Published by FEBS Press and John Wiley & Sons Ltd.

The inorganic speciation of tin(II) in aqueous solution

NASA Astrophysics Data System (ADS)

Cigala, Rosalia Maria; Crea, Francesco; De Stefano, Concetta; Lando, Gabriele; Milea, Demetrio; Sammartano, Silvio

2012-06-01

This paper reports new voltammetric measurements on the interactions between tin(II) and the most important natural inorganic ligands, OH-, Cl-, F-, CO32-, SO42- and PO43-. For a better understanding of tin(II) speciation, an analysis is also given of prior data on the same systems from the literature. The formation constants were determined at t = 25 °C in different ionic media and at different ionic strengths, specifically the following: Sn(OH)q (0.1 ⩽ I/mol L-1 ⩽ 1.0 in NaNO3), SnClr and Sn(OH)Cl (0.1 ⩽ I/mol L-1 ⩽ 2.3 in Na(NO3, Cl)), Sn(SO4)r (0.1 ⩽ I/mol L-1 ⩽ 1.6 in Na(NO3, SO4)), SnHqCO3 and SnHqPO4 (0.15 ⩽ I/mol L-1 ⩽ 1.0 in NaNO3), where the subscripts r and q represent the stoichiometric coefficients. Concerning the SnFr species, reliable literature values were considered (0.15 ⩽ I/mol L-1 ⩽ 1.0 in NaClO4). Fifteen voltammetric measurements were performed in synthetic seawater; the total seawater binding ability was evaluated by a model in which synthetic seawater is expressed as a single salt, BA. The formation of species between tin(II) and the anion of the marine salt (A) was also proposed, and the corresponding stability constants at different salinities (5 ⩽ S ⩽ 50) were reported. In addition, studies on the solubility of Sn(OH)2(s) were carried out using voltammetry and light scattering measurements. The "extra-stability" of the mixed species with respect to the parent species was evaluated, in particular for Sn(OH)Cl and the corresponding species involving the anion of the marine salt (A). The dependence of the formation constants on ionic strength was analysed using extended Debye-Hückel and Specific ion Interaction Theory (SIT) type equations. Tin(II) speciation was also evaluated in different natural fluid conditions, where, in all cases, carbonate complexation was predominant, hampering the formation of hydrolytic species throughout the investigated pH range. Moreover, some formation enthalpy changes were calculated for the Sn(OH)+, Sn(OH)2(aq), Sn(OH)2(s), Sn(OH)3-, Sn(OH)22+, Sn(OH)42+, Sn(OH)Cl, SnCl+, SnCl2 and SnCl3- species on the basis of the available literature stability constant values at different temperatures and using the empirical relationships reported in the literature. The ΔH values at t = 25 °C were positive in all cases except for the Sn(OH)2(s) and Sn(OH)3- species, indicating an increase in the stability constant values with increasing temperature. This work represents an advance in the knowledge, understanding and modelling of the inorganic speciation of tin(II) in natural fluids, particularly for solutions containing chloride, fluoride, sulphate, carbonate and phosphate anions.

Electrodeposition and Characterization of Hydroxyapatite on TiN/316LSS.

PubMed

Nam, Pham Thi; Lam, Tran Dai; Huong, Ho Thu; Phuong, Nguyen Thu; Trang, Nguyen Thi Thu; Hoang, Thai; Huong, Nguyen Thi Thanh; Thang, Le Ba; Drouet, Christophe; Grossin, David; Kergourlay, Emmanuelle; Bertrand, Ghislaine; Devilliers, Didier; Thanh, Dinh Thi Mai

2015-12-01

The deposition of TiN on stainless steel substrates may improve the stability and compatibility of this material with bone, which may be advantageously exploited for the elaboration of advanced pros- thetic devices. In this work, TiN-coated 316LSS (by way of DC magnetron sputtering) was used as a starting material for investigating the electrochemical post-deposition of hydroxyapatite (HAp) which has a composition close to that of bone. Electrodeposition was carried out starting from an aqueous medium containing solubilized Ca(NO3)2 and NH4H2PO4 in the presence of H2O2. We report the influence of experimental conditions on the morphology of the obtained HAp coating on TiN/316LSS. The effect of applied potential, temperature, H2O2 concentration, pH and duration of reaction were thoroughly discussed on the basis of X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier Transform Infrared (FTIR) spectroscopy and Energy Dispersive X-ray Spectroscopy (EDX) results. This method appears advantageous for producing HAp-coated implant materials.

Binders and Hosts for High-Capacity Lithium-ion Battery Anodes

NASA Astrophysics Data System (ADS)

Dufficy, Martin Kyle

Lithium-ion batteries (LIBs) are universal electrochemical energy storage devices that have revolutionized our mobile society. Nonetheless, societal and technological advances drive consumer demand for LIBs with enhanced electrochemical performance, such as higher charge capacity and longer life, compared to conventional LIBs. One method to enhance LIB performance is to replace graphite, the industry standard anode since commercialization of LIBs in 1991, with high-charge capacity materials. Implementing high-capacity anode materials such as tin, silicon, and manganese vanadates, to LIBs presents challenges; Li-insertion is destructive to anode framework, and increasing capacity increases structural strains that pulverize anode materials and results in a short-cycle life. This thesis reports on various methods to extended the cycle life of high-capacity materials. Most of the work is conducted on nano-sized anode materials to reduce Li and electron transport pathway length (facilitating charge-transfer) and reduce strains from volume expansions (preserving anode structure). The first method involves encapsulating tin particles into a graphene-containing carbon nanofiber (CNF) matrix. The composite-CNF matrix houses tin particles to assume strains from tin-volume expansions and produces favorable surface-electrolyte chemistries for stable charge-discharge cycling. Before tin addition, graphene-containing CNFs are produced and assessed as anode materials for LIBs. Graphene addition to CNFs improves electronic and mechanical properties of CNFs. Furthermore, the 2-D nature of graphene provides Li-binding sites to enhance composite-CNF both first-cycle and high-rate capacities > 150% when compared to CNFs in the absence of graphene. With addition of Sn, we vary loadings and thermal production temperature to elucidate structure-composition relationships of tin and graphene-containing CNF electrodes that lead to increased capacity retention. Of note, electrodes containing ≤ 20 wt% tin result in small tin (metallic and tin oxide) particles (≤ 15 nm) within the composite-CNF matrix, which yield long cycle-lives; large reversible capacities of ˜ 600 mAh g-1 are observed at 0.2-C rates, while capacities of ˜ 400 mAh g-1 (double the capacity of CNFs) are observed after hundreds of cycles at 2-C rates. The second method comprises an approach to enhance the cycle life of silicon anodes. Many researchers believe that Si is the future anode material of LIBs, and Si is capable of providing a much needed boost in overall cell performance. Silicon has the highest known charge capacity at ˜ 3579 mAh g-1, nearly an order of magnitude larger than graphite (372 mAh g-1). In attempt to realize the entire capacity of Si anodes, we use binding agents to prolong cycle life. Binding agents enhance capacity retention via favorable interactions with cell components such as active materials and electrolytes. In this study, we introduce galactomannans (specifically, guar) as viable, inexpensive, biopolymer binders for Si electrodes. In attempt to elucidate the role of the binder in Si electrodes, we study guar-electrode and -electrolyte interactions that lead to electrochemical performance enhancements. We recognize that there are deficiencies in guar-silicon systems, which we address in our following approach. Notably, we develop a guar-derived binder to increase the strength and conductivity of Si-based electrodes by crosslinking guar and carbon black dispersions. The crosslinked binders, in effect, enhance electrode adhesion and hinder electrode cracking by self-healing. This study monitors gelation via rheological methods and assesses effects of crosslinking density on physical and electrochemical properties. Lastly, we consider a vacancy-induced manganese vanadate as high-capacity, high-power anodes for LIBs. Rather than assessing nanoparticles, we tailored molecular structure to enhance electrochemical performances. X-ray diffraction studies enable us to suggest a Li-insertion mechanism, where Li travels through large channels created by defects in the crystal structure. The ensuing manganese vanadate structure produces a stable framework that results in stable cycling of hundreds of cycles.

Optical properties of trinuclear metal chalcogenolate complexes - room temperature NIR fluorescence in [Cu2Ti(SPh)6(PPh3)2].

PubMed

Kühn, Michael; Lebedkin, Sergei; Weigend, Florian; Eichhöfer, Andreas

2017-01-31

The optical properties of four isostructural trinuclear chalcogenolato bridged metal complexes [Cu 2 Sn(SPh) 6 (PPh 3 ) 2 ], [Cu 2 Sn(SePh) 6 (PPh 3 ) 2 ], [Ag 2 Sn(SPh) 6 (PPh 3 ) 2 ] and [Cu 2 Ti(SPh) 6 (PPh 3 ) 2 ] have been investigated by absorption and photoluminescence spectroscopy and time-dependent density functional theory (TDDFT) calculations. All copper-tin compounds demonstrate near-infrared (NIR) phosphorescence at ∼900-1100 nm in the solid state at low temperature, which is nearly absent at ambient temperature. Stokes shifts of these emissions are found to be unusually large with values of about 1.5 eV. The copper-titanium complex [Cu 2 Ti(SPh) 6 (PPh 3 ) 2 ] also shows luminescence in the NIR at 1090 nm but with a much faster decay (τ ∼ 10 ns at 150 K) and a much smaller Stokes shift (ca. 0.3 eV). Even at 295 K this fluorescence is found to comprise a quantum yield as high as 9.5%. The experimental electronic absorption spectra well correspond to the spectra simulated from the calculated singlet transitions. In line with the large Stokes shifts of the emission spectra the calculations reveal for the copper-tin complexes strong structural relaxation of the excited triplet states whereas those effects are found to be much smaller in the case of the copper-titanium complex.

Differences in the INR evaluation of two different thromboplastins in patients with positivity to lupus anticoagulant in ongoing oral anticoagulation.

PubMed

Ferrazzi, Paola; Colombo, Anna; Di Micco, Pierpaolo; Lodigiani, Corrado; Librè, Luca; Rota, Lidia Luciana; Montanelli, Alessandro; Quaglia, Ilaria

2010-01-01

A possible interference between lupus anticoagulant (LAC), a well characterized clotting inhibitor, in the International Normalized Ratio (INR) determination during oral anticoagulation (OA) has been reported in the literature. Few data are available about the relationship between this kind of interference and the daily clinical management of oral anticoagulation. The aim of the study is to evaluate the role of two different thromboplastins-RecombiPlasTin 2G and HepatoComplex-in the determination of INR values of several patients' ongoing OA for a previous thrombotic disorder with and without positivity to LAC, and to evaluate possible interferences in the daily therapeutic approach. We selected 16 patients (13 females and 3 males, mean age 59 ± 16 years) with LAC positivity ongoing OA and 11 control subjects (7 females and 4 males, mean age 58 ± 14.5 years) with similar characteristics (ie, ethnic background and weight) with LAC negativity ongoing OA. 165 assays for INR determination were analyzed from both groups. Statistical analysis was performed using STATA 10 software. P values were considered significant if <0.05. Mean values of INR for patients with LAC positivity were 3.79 ± 1.63 when tested with RecombiPlasTin 2G vs 3.18 ± 1.15 when tested with HepatoComplex (P < 0.001, s); while mean values of INR for patients with antiphospholipid syndrome (APS) with LAC negativity were 3.54 ± 1.39 when tested with RecombiPlasTin 2G vs 3.23 ± 1.14 when tested with HepatoComplex (P < 0.002, s). An INR value > than 4.5 was found in 31/165 samples in 9 subjects, 8 patients with LAC positivity, and 1 control group subject with LAC negativity. There was a great difference in INR values in these subjects if we use the common thromboplastin (ie, RecombiPlasTin 2G) with a INR range varying from 5.14 ± 0.35 vs 3.79 ± 0.38 if we use another thromboplastin (ie, HepatoComplex) (P < 0.001, s). A change in the therapeutic approach for OA is possible in these cases because different INR values were obtained using different thromboplastins. Our data confirm that INR evaluation does not reveal significant changes also if tested with two different thromboplastins, for patients ongoing OA with and without LAC positivity, when the INR value is < than 4. Over this INR value there is a significant difference in patients with LAC positivity if we use a different thromboplastin for the INR determination. For this reason values obtained by RecombiPlasTin 2G need to be confirmed and matched with another thromboplastin (ie, HepatoComplex). This approach may be useful in order to have a good INR testing for the chronic long-term treatment with OA in particular in patients with LAC positivity.

Combined Tin-Containing Fluoride Solution and CO2 Laser Treatment Reduces Enamel Erosion in vitro.

PubMed

Esteves-Oliveira, Marcella; Witulski, Nadine; Hilgers, Ralf-Dieter; Apel, Christian; Meyer-Lueckel, Hendrik; Eduardo, Carlos de Paula

2015-01-01

The aim of this in vitro study was to evaluate the effect of combined CO2 laser and tin-containing fluoride treatment on the formation and progression of enamel erosive lesions. Ninety-six human enamel samples were obtained, stored in thymol solution and, after surface polishing, randomly divided into 6 different surface treatment groups (n = 16 in each group) as follows: no treatment, control (C); one CO2 laser irradiation (L1); two CO2 laser irradiations (L2); daily application of fluoride solution (F); combined daily fluoride solution + one CO2 laser irradiation (L1F), and combined daily fluoride solution + two CO2 laser irradiations (L2F). Laser irradiation was performed at 0.3 J/cm2 (5 µs/226 Hz/10.6 µm) on day 1 (L1) and day 6 (L2). The fluoride solution contained AmF/NaF (500 ppm F), and SnCl2 (800 ppm Sn) at pH 4.5. After surface treatment the samples were submitted to an erosive cycling over 10 days, including immersion in citric acid (2 min/0.05 M/pH = 2.3) 6 times daily and storage in remineralization solution (≥1 h) between erosive attacks. At the end of each cycling day, the enamel surface loss (micrometers) was measured using a 3D laser profilometer. Data were statistically analyzed by means of a 2-level mixed effects model and linear contrasts (α = 0.05). Group F (-3.3 ± 2.0 µm) showed significantly lower enamel surface loss than groups C (-27.22 ± 4.1 µm), L1 (-18.3 ± 4.4 µm) and L2 (-16.3 ± 5.3 µm) but higher than L1F (-1.0 ± 4.4 µm) and L2F (1.4 ± 3.2 µm, p < 0.05). Under the conditions of this in vitro study, the tin-containing fluoride solution caused 88% reduction of enamel surface loss, while its combination with CO2 laser irradiation at 0.3 J/cm2 hampered erosive loss almost completely. © 2015 S. Karger AG, Basel.

Crystal structure of bis­{μ-(E)-2-[(2-oxido­phenyl­imino)­meth­yl]quinolin-8-olato-κ4 O,N,N′,O′}bis­[di­butyl­tin(IV)

PubMed Central

Carlos, Camacho-Camacho; Naytzé, Ortiz-Pastrana; Ariadna, Garza-Ortiz; Irma, Rojas-Oviedo

2017-01-01

Condensation of 8-hy­droxy­quinoline-2-carbaldehyde with 2-amino­phenol gave the (E)-2-[(2-hy­droxy­phenyl­imino)­meth­yl]quinolin-8-ol derivative that reacted with di-n-butyl­tin oxide with release of H2O to yield the chelate title complex, [Sn2(C4H9)4(C16H10N2O2)2]. The compound crystallizes in the triclinic space group P-1, with two independent centrosymmetric dimers in the unit cell. Each features a typical pincer-type structure where the dianionic ligand is tetra­dentate, coordinating to the central tin atom through both phenolate oxygen atoms, as well as through the quinoline and imine N atoms. Each metal atom adopts a distorted penta­gonal–bipyramidal SnC2N2O3 coordination arising from the N,N′,O,O′-tetra­dentate deprotonated Schiff base, one bridging phenolate O atom of the neighbouring ligand and two butyl groups in the axial sites. PMID:28083122

Effect of pH and sulfur precursor concentration on electrochemically deposited CZTS thin films using glycine as the complexing agent

NASA Astrophysics Data System (ADS)

Paraye, Akanksha; Sani, Rabiya; Ramachandran, Manivannan; Selvam, Noyel Victoria

2018-03-01

Copper zinc tin sulfide (CZTS) a promising quaternary chalcogenide material was deposited using single step electrodeposition using glycine as the complexing agent. The deposition was studied at different sulfur concentrations and at different pH. The pH of the electrolyte was found to influence the stoichiometry of the deposits significantly. The deposits formed at pH 2.5 showed satisfactory stoichiometry. The thickness of the deposits was observed to decrease with increase in sulfur concentration and pH. The transmission electron spectroscopy analysis showed the formation of flower shaped core shell particles from the electrolyte that contained 80 mM sulfur precursor at pH 2.5. The band gap of the deposits was found to be in the range from 1.57 eV to 2.1 eV. X-ray diffraction analysis showed that the as synthesized particles were amorphous in nature, the crystallinity of which improved with annealing. The Mott Schottky analysis of the deposits in 0.1 M sodium perchlorate showed that the particles exhibited p-type conductivity.

PHASE DIAGRAM FOR THE SYSTEM TITANIUM-TIN (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kornilov, I.I.; Nartova, T.T.

1960-03-01

Differential thermal analysis, microstructural analyses, and determinations of hardness values and electric resistance were used to construct a diagram of state for the binary system Ti-Sn up to the composition of the compound Ti/sub 3/Sn (from 0 to 25 at.% Sn). Analyses of the thermograms showed that all conversions proceeding with the absorption of heat could be detected on the heating curves. Tin lowers the temperature of conversion of titunium with 5.0 at.% tin first to a minimum at 860 tained C which then increases to 890 tained C at higher tin contents. A peritectoid reaction ( alpha / submore » 2/ were ob ore resistant t + ) takes place with a conversion temperature at 890 tained C. A HF-HNO/sub 3/-glycerin etch showed a single-phase homogeneous structure of an alpha -solid solution with alloys containing up to 9 at.% Q. The amount of a second -phase increases with increasing tin content until a single-phase structure of a -solid solution of the compound Ti/sub 3/Sn is noted with alloys containing 23 to 25 at.% Sn. Alloys containing 8 to 22.5 at.% Sn undergo a peritectoid reaction, at a temperature of 890 tained C as shown by thermal analyses and by microstructural analyses of samples quenched frorn above and below the conversion temperature. A study of the microstructure of quenched alloys showed that the solubility of tin in ore resistant t -titanium increases from 8 at.% Sn at 890 tained C to 10.5 at.% Sn at 1100 tained C. X-ray analyses of annealed samples of alloy showed only the lines of an alpha solid solution for 5, 8, 9 at.% Sn, a -solid solution for 23 at.% Sn (close to the composition Ti/sub 3/Sn), and an alpha and mixed phase for a 15 at.% Sn. Vickers hardness numbers were determined with a diamond pyramid at a loading of 10 kg. The hardness increases smoothly with increasing tin content to a maximum at the saturation solubility of the tin in the alpha - or ore resistant t -solid solution. The hardness decreases smoothly with the appearance of the -phase until it attains a minimum at the composition of the compound Ti/sub 3/Sn. The specific electric resistance increases with an increase of tin in the solid solution of alpha -titanium. The rate of increase of the specific electric resistance decreases markedly with the appearance of the -phase. The electric resistance of an alloy with 14.3 at.% Sn was studied as a function of temperature from room temperature to 1100 tained C in special vacuum equipment. A sharp drop in electric resistance a; 890 tained C confirmed the existence of a peritectoid reaction in the system Ti-Sn. (TTT)« less

The Tin Bider Impact Structure, Algeria: New Map with Field Inputs on Structural Aspect

NASA Astrophysics Data System (ADS)

Kassab, F.; Belhai, D.

2017-07-01

The Tin Bider impact structure is a complex type composed by sedimentary target rocks. We realized a geological map including new inputs on impact characters of a recent field investigation where we identify shatter cone and folds.

Dissection of affinity captured LINE-1 macromolecular complexes

PubMed Central

Mita, Paolo; Jiang, Hua; Adney, Emily M; Wudzinska, Aleksandra; Badri, Sana; Ischenko, Dmitry; Eng, George; Burns, Kathleen H; Fenyö, David; Chait, Brian T; Alexeev, Dmitry; Rout, Michael P; Boeke, Jef D

2018-01-01

Long Interspersed Nuclear Element-1 (LINE-1, L1) is a mobile genetic element active in human genomes. L1-encoded ORF1 and ORF2 proteins bind L1 RNAs, forming ribonucleoproteins (RNPs). These RNPs interact with diverse host proteins, some repressive and others required for the L1 lifecycle. Using differential affinity purifications, quantitative mass spectrometry, and next generation RNA sequencing, we have characterized the proteins and nucleic acids associated with distinctive, enzymatically active L1 macromolecular complexes. Among them, we describe a cytoplasmic intermediate that we hypothesize to be the canonical ORF1p/ORF2p/L1-RNA-containing RNP, and we describe a nuclear population containing ORF2p, but lacking ORF1p, which likely contains host factors participating in target-primed reverse transcription. PMID:29309035

Nickel-Tin Electrode Materials for Nonaqueous Li-Ion Cells

NASA Technical Reports Server (NTRS)

Ehrlich, Grant M.; Durand, Christopher

2005-01-01

Experimental materials made from mixtures of nickel and tin powders have shown promise for use as the negative electrodes of rechargeable lithium-ion electrochemical power cells. During charging (or discharging) of a lithium-ion cell, lithium ions are absorbed into (or desorbed from, respectively) the negative electrode, typically through an intercalation or alloying process. The negative electrodes (for this purpose, designated as anodes) in state-of-the-art Li-ion cells are made of graphite, in which intercalation occurs. Alternatively, the anodes can be made from metals, in which alloying can occur. For reasons having to do with the electrochemical potential of intercalated lithium, metallic anode materials (especially materials containing tin) are regarded as safer than graphite ones; in addition, such metallic anode materials have been investigated in the hope of obtaining reversible charge/discharge capacities greater than those of graphite anodes. However, until now, each of the tin-containing metallic anode formulations tested has been found to be inadequate in some respect.

BAC-MP4 predictions of thermochemistry for the gas-phase tin compounds in the Sn-H-C-Cl system.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allendorf, Mark D.; Melius, Carl F.

2004-09-01

In this work, the BAC-MP4 method is extended for the first time to compounds in the fourth row of the periodic table, resulting in a self-consistent set of thermochemical data for 56 tin-containing molecules in the Sn-H-C-Cl system. The BAC-MP4 method combines ab initio electronic structure calculations with empirical corrections to obtain accurate heats of formation. To obtain electronic energies for tin-containing species, the standard 6-31G(d,p) basis set used in BAC-MP4 calculations is augmented with a relativistic effective core potential to describe the electronic structure of the tin atom. Both stable compounds and radical species are included in this study.more » Trends within homologous series and calculated bond dissociation energies are consistent with previous BAC-MP4 predictions for group 14 compounds and the limited data available from the literature, indicating that the method is performing well for these compounds.« less

The episodic influx of tin-rich cosmic dust particles during the last ice age

NASA Astrophysics Data System (ADS)

LaViolette, Paul A.

2015-12-01

This paper presents evidence of the first detection of interstellar dust in ice age polar ice. Neutron activation analysis (NAA) results are reported for 15 elements found in dust filtered from eight samples of Camp Century Greenland ice dating from 40 to 78 kyrs BP. High concentrations of Sn, Sb, Au, Ag, Ir, and Ni were found to be present in three out of these eight samples. One compositionally anomalous dust sample from an ice core depth of 1230.5 m (age ∼49 kyrs BP, near the beginning of D/O stadial No. 13) was found to contain tin with an average weight percent of 49% as determined by energy dispersive X-ray analysis (EDS). This sample was also found to contain high concentrations of Pb with an average weight abundance of 8.4% and matching the Sn:Pb ratio observed in interstellar spectra. Dust particles in this sample generally have a platy morphology and range from submicron size up to a size as large as 120 μm, a particle consisting almost entirely of SnO2 and being the largest monomineralic extraterrestrial dust particle so far discovered. One porous aggregate tin-bearing particle was found to contain nanometer sized chondrules indicating an extraterrestrial origin. The extraterrestrial origin for the tin is also indicated by the presence of isotopic anomalies in the 114Sn, 115Sn and 117Sn isotopes. Follow up isotopic measurements of this tin-rich dust need to be performed to improve confidence in the anomalies reported here. High abundances of the low melting point elements Ag, Au, and Sb are also present in this tin-rich sample along with elevated abundances of the siderophiles Ir, Ni, Fe, and Co, the latter being present in chondritic proportions and indicating that about 9% of the dust has a C1 chondrite component. Measurements indicate that about 97% of this dust is of extraterrestrial origin with a 3% residual being composed of terrestrial windblown dust. EDS analysis of another tin-rich Camp Century ice core dust sample dating to ∼130 kyrs BP was found to contain tin-rich particles with a similar platy morphology and to have Sn and Pb weight abundances averaging 39% and 7.5% respectively, again approximating the interstellar Sn:Pb ratio. The relative absence of cosmic microspheres and the unmelted appearance of the tin-rich particles in both of these samples suggests that these particles entered the Earth's atmosphere at low velocity, implicating a gradual accumulation of dust from a dispersed state in the near Earth space environment. The unusual enhancement of Sn and Pb could be explained if these dust particles were originally present in the solar system's interstellar environment in a superconducting native metal state and were preferentially concentrated through Meissner effect forces by the passage of cosmic ray driven hydromagnetic shocks which may also have transported them into the solar system. The 49 kyrs BP event is estimated to have lasted over 6 years and to have deposited dust onto the Earth at a rate 104-105 times higher than present rates. This had a significant cooling effect on climate and resulted in a transient 33 fold increase in snow accumulation. Future discovery of these events in ice cores at other locations should void any lingering thoughts that this heavy metal enhancement may be due to sample contamination.

Oxidation characteristics of Ti-25Al-10Nb-3V-1Mo intermetallic alloy

NASA Technical Reports Server (NTRS)

Wallace, Terryl A.; Clark, Ronald K.; Sankaran, Sankara N.; Wiedemann, Karl E.

1990-01-01

Static oxidation kinetics of the super-alpha 2 titanium-aluminide alloy Ti-25Al-10Nb-3V-1Mo (at. percent) were investigated in air over the temperature range of 650 to 1000 C using thermogravimetric analysis. The oxidation kinetics were complex at all exposure temperatures and displayed up to three distinct oxidation rates. Breakaway oxidation occurred after long exposure times at high temperatures. Oxidation products were determined using x ray diffraction techniques, electron microprobe analysis, and energy dispersive x ray analysis. Oxide scale morphology was examined by scanning electron microscopy of the surfaces and cross sections of oxidized specimens. The oxides during the parabolic stages were compact and multilayered, consisting primarily of TiO2 doped with Nb, a top layer of Al2O3, and a thin bottom layer of TiN. The transition between the second and third parabolic stage was found to be linked to the formation of a TiAl layer at the oxide-metal interface. Porosity was formed during the third stage, causing degradation of the oxide and the beginning of breakaway oxidation.

Process for preparing titanium nitride powder

DOEpatents

Bamberger, C.E.

1988-06-17

A process for making titanium nitride powder by reaction of titanium phosphates with sodium cyanide. The process of this invention may comprise mixing one or more phosphates of Ti with a cyanide salt in the absence of oxygen and heating to a temperature sufficient to cause reaction to occur. In the preferred embodiment the ratio of cyanide salt to Ti should be at least 2 which results in the major Ti-containing product being TiN rather than sodium titanium phosphate byproducts. The process is an improvement over prior processes since the byproducts are water soluble salts of sodium which can easily be removed from the preferred TiN product by washing. 2 tabs.

Copper-Zinc-Tin-Sulfur Thin Film Using Spin-Coating Technology

PubMed Central

Yeh, Min-Yen; Lei, Po-Hsun; Lin, Shao-Hsein; Yang, Chyi-Da

2016-01-01

Cu2ZnSnS4 (CZTS) thin films were deposited on glass substrates by using spin-coating and an annealing process, which can improve the crystallinity and morphology of the thin films. The grain size, optical gap, and atomic contents of copper (Cu), zinc (Zn), tin (Sn), and sulfur (S) in a CZTS thin film absorber relate to the concentrations of aqueous precursor solutions containing copper chloride (CuCl2), zinc chloride (ZnCl2), tin chloride (SnCl2), and thiourea (SC(NH2)2), whereas the electrical properties of CZTS thin films depend on the annealing temperature and the atomic content ratios of Cu/(Zn + Sn) and Zn/Sn. All of the CZTS films were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDXS), Raman spectroscopy, and Hall measurements. Furthermore, CZTS thin film was deposited on an n-type silicon substrate by using spin-coating to form an Mo/p-CZTS/n-Si/Al heterostructured solar cell. The p-CZTS/n-Si heterostructured solar cell showed a conversion efficiency of 1.13% with Voc = 520 mV, Jsc = 3.28 mA/cm2, and fill-factor (FF) = 66%. PMID:28773647

Optical response of mixed methylammonium lead iodide and formamidinium tin iodide perovskite thin films

DOE PAGES

Ghimire, Kiran; Zhao, Dewei; Yan, Yanfa; ...

2017-07-13

Here, mixed tin (Sn) and lead (Pb) based perovskite thin films have been prepared by solution processing combining methylammonium lead iodide (MAPbI 3) and formamidinium tin iodide (FASnI 3) precursors. Optical response in the form of complex dielectric function (ε = ε 1 + iε 2) spectra and absorption coefficient (α) spectra of (FASnI 3) 1-x(MAPbI 3) x based perovskite films have been extracted over a spectral range 0.74 to 5.89 eV using spectroscopic ellipsometry. Absorption band edge energy changes as a function of composition for films including FASnI 3, MAPbI 3, and mixed x = 0.20, 0.35, 0.40, andmore » 0.6 (FASnI 3) 1-x(MAPbI 3) x perovskites. (FASnI 3) 0.60(MAPbI 3) 0.4 is found to have the minimum absorption band edge energy near ~1.2 eV.« less

Further studies of the anodic dissolution in sodium chloride electrolyte of aluminium alloys containing tin and gallium

NASA Astrophysics Data System (ADS)

Nestoridi, Maria; Pletcher, Derek; Wharton, Julian A.; Wood, Robert J. K.

As part of a programme to develop a high power density, Al/air battery with a NaCl brine electrolyte, the high rate dissolution of an aluminium alloy containing tin and gallium was investigated in a small volume cell. The objective was to define the factors that limit aluminium dissolution in condition that mimic a high power density battery. In a cell with a large ratio of aluminium alloy to electrolyte, over a range of current densities the extent of dissolution was limited to ∼1000 C cm -2 of anode surface by a thick layer of loosely bound, crystalline deposit on the Al alloy anode formed by precipitation from solution. This leads to a large increase in impedance and acts as a barrier to transport of ions.

Carbon materials-functionalized tin dioxide nanoparticles toward robust, high-performance nitrogen dioxide gas sensor.

PubMed

Zhang, Rui; Liu, Xiupeng; Zhou, Tingting; Wang, Lili; Zhang, Tong

2018-08-15

Carbon (C) materials, which process excellent electrical conductivity and high carrier mobility, are promising sensing materials as active units for gas sensors. However, structural agglomeration caused by chemical processes results in a small resistance change and low sensing response. To address the above issues, structure-derived carbon-coated tin dioxide (SnO 2 ) nanoparticles having distinct core-shell morphology with a 3D net-like structure and highly uniform size are prepared by careful synthesis and fine structural design. The optimum carbon-coated SnO 2 nanoparticles (SnO 2 /C)-based gas sensor exhibits a low working temperature, excellent selectivity and fast response-recovery properties. In addition, the SnO 2 /C-based gas sensor can maintain a sensitivity to nitrogen dioxide (NO 2 ) of 3 after being cycled 4 times at 140 °C for, suggesting its good long-term stability. The structural integrity, good synergistic properties, and high gas-sensing performance of SnO 2 /C render it a promising sensing material for advanced gas sensors. Copyright © 2018 Elsevier Inc. All rights reserved.

Equilibrium Tin Isotope Fractionation during Metal-Sulfide-Silicate Differentiation: A Nuclear Resonant Inelastic X-ray Scattering Approach

NASA Astrophysics Data System (ADS)

Roskosz, M.; Amet, Q.; Fitoussi, C.; Laporte, D.; Hu, M. Y.; Alp, E. E.

2016-12-01

Metal-silicate differentiation was recently addressed through the insight of the isotopic composition of siderophile elements (mainly Fe, Si and Cr isotopes) of planetary and extraterrestrial bodies. A key limitation of this approach is however the knowledge of equilibrium fractionation factors between coexisting phases (metal alloys, silicates and sulfides) used to interpret data on natural samples. These properties are difficult to determine experimentally. In this context, tin is generally classified as a chalcophile element but it is also siderophile and volatile. We applied a synchrotron-based method to circumvent difficulties related to determination of equilibrium isotope fractionation. The nuclear resonant inelastic x-ray scattering (NRIXS) was used to measure the phonon excitation spectrum and then to derive the force constant and finally the fractionation factors of Sn-bearing geomaterials. Spectroscopic measurements were carried out at room pressure at Sector 30-ID (APS, USA). A range of Fe-Ni alloys, rhyolitic and basaltic glasses and iron sulfides containing isotopically enriched 119Sn were synthesized. The tin content and the redox conditions prevailing during the synthesis were varied. The data evaluation was carried out using PHOENIX and SciPhon programs. A strong effect of both the redox state and the tin content was measured. In addition, the composition of the silicate glasses was found to be another important factor determining the tin isotope metal-silicate-sulfide fractionation factors. Our results are consistent with trends previously observed in the case of iron isotopes [1,2]. We will discuss the implications of our experimental results in terms of tin isotope planetary signatures. References: [1] Dauphas et al. (2014), EPSL, 398, 127-140; [2] Roskosz et al. (2015), GCA, 169, 184-199.

Platinum phosphinothiolato hydride complexes: synthesis, structure and evaluation as tin-free hydroformylation catalysts.

PubMed

Real, Julio; Prat-Gil, Esther; Pagès-Barenys, Montserrat; Polo, Alfonso; Piniella, Joan F; Álvarez-Larena, Ángel

2016-03-07

Ligand 2-diphenylphosphinothiophenol (Hsarp) reacted with Pt(PPh3)4 to yield trans-[PtH(sarp)(PPh3)], which undergoes fast exchange with free PPh3 on the NMR time scale and very slowly and reversibly formed some cis-[PtH(sarp)(PPh3)] over time in solution (11%, 24 h). Reaction of trans-[PtH(sarp)(PPh3)] with Hsarp in boiling toluene gave cis- and trans-[Pt(sarp)2]; the cis isomer being more stable. These complexes were characterized by (1)H and (31)P NMR and also analyzed by XRD in the case of trans-[PtH(sarp)(PPh3)], trans-[Pt(sarp)2], and cis-[Pt(sarp)2]. trans-[PtH(sarp)(PPh3)] was evaluated as a preformed, tin-free hydroformylation catalyst on styrene and found active at 100 °C, at pressures over 75 bar, yielding phenylpropanal (regioselectivities up to 83% in 2-phenylpropanal), with total conversions to aldehydes up to 100% at styrene/platinum ratios from 400/1 to 1000/1 and minimal hydrogenation products.

Morphology and Gas-Sensing Properties of Tin Oxide Foams with Dual Pore Structure

NASA Astrophysics Data System (ADS)

Nam, Kyungju; Kim, Hyeong-Gwan; Choi, Hyelim; Park, Hyeji; Kang, Jin Soo; Sung, Yung-Eun; Lee, Hee Chul; Choe, Heeman

2017-06-01

Tin oxide is a commonly used gas-sensing material, which can be applied as an n- or p-type gas sensor. To improve the gas-sensing performance of tin oxide, we successfully synthesized tin oxide foam via an ice-templating or freeze-casting method. The tin oxide foam samples showed different morphological features depending on the major processing parameters, which include sintering temperature, sintering time, and the amount of added powder. Based on scanning electron microscopy images, we could identify dual pore structure of tin oxide foam containing `wall' pores ranging from 5.3 μm to 10.7 μm, as well as smaller secondary pores (a few micrometers in size) on the wall surfaces. Gas-sensing performance tests for the synthesized tin oxide foams reveal a sensitivity of 13.1, a response time of 192 s, and a recovery time of 160 s at an ethanol gas concentration of 60 ppm at 300°C. This is a remarkable result given that it showed p-type semiconductor behavior and was used without the addition of any catalyst.

Process for making a noble metal on tin oxide catalyst

NASA Technical Reports Server (NTRS)

Upchurch, Billy T. (Inventor); Davis, Patricia (Inventor); Miller, Irvin M. (Inventor)

1989-01-01

A quantity of reagent grade tin metal or compound, chloride-free, and high-surface-area silica spheres are placed in deionized water, followed by deaerating the mixture by boiling and adding an oxidizing agent, such as nitric acid. The nitric acid oxidizes the tin to metastannic acid which coats the spheres because the acid is absorbed on the substrate. The metastannic acid becomes tin oxide upon drying and calcining. The tin-oxide coated silica spheres are then placed in water and boiled. A chloride-free precious metal compound in aqueous solution is then added to the mixture containing the spheres, and the precious metal compound is reduced to a precious metal by use of a suitable reducing agent such as formic acid. Very beneficial results were obtained using the precious metal compound tetraammine platinum(II) hydroxide.

A-15 Superconducting composite wires and a method for making

DOEpatents

Suenaga, Masaki; Klamut, Carl J.; Luhman, Thomas S.

1984-01-01

A method for fabricating superconducting wires wherein a billet of copper containing filaments of niobium or vanadium is rolled to form a strip which is wrapped about a tin-alloy core to form a composite. The alloy is a tin-copper alloy for niobium filaments and a gallium-copper alloy for vanadium filaments. The composite is then drawn down to a desired wire size and heat treated. During the heat treatment process, the tin in the bronze reacts with the niobium to form the superconductor niobium tin. In the case where vanadium is used, the gallium in the gallium bronze reacts with the vanadium to form the superconductor vanadium gallium. This new process eliminates the costly annealing steps, external tin plating and drilling of bronze ingots required in a number of prior art processes.

Wrapping process for fabrication of A-15 superconducting composite wires

DOEpatents

Suenaga, M.; Klamut, C.J.; Luhman, T.S.

1980-08-15

A method for fabricating superconducting wires wherein a billet of copper containing filaments of niobium or vanadium is rolled to form a strip which is wrapped about a tin-alloy core to form a composite. The alloy is a tin-copper alloy for niobium filaments and a gallium-copper alloy for vanadium filaments. The composite is then drawn down to a desired wire size and heat treated. During the heat treatment process, the tin in the bronze reacts with the niobium to form the superconductor niobium tin. In the case where vanadium is used, the gallium in the gallium bronze reacts with the vanadium to form the superconductor vanadium gallium. This new process eliminates the costly annealing steps, external tin plating and drilling of bronze ingots required in a number of prior art processes.

Effect of Sn on the oxide subscale structure formed on a 3% Si steel

NASA Astrophysics Data System (ADS)

Cesar, Maria das G. M. M.; Silveira, Carolina C.; Paolinelli, Sebastião C.; Cicale, Stefano

2018-04-01

Addition of tin in 3% Si steel is a method to improve magnetic properties since tin in steel is known as an element that segregates at grain boundaries, inhibits grain growth and has a dragging effect on grain boundary movement. However, tin is generally known as an element that has a harmful effect on surface coating properties. The oxide subscale formed on the decarburization annealing of a 3% Si steel containing tin was investigated by SEM, EDS, GDS and FTIR. The forsterite film was evaluated by SEM, EDS and GDS. The higher tin content decreased thickness, oxygen and fayalite/silica ratio in the subscale and resulted into a discontinuous forsterite film with poor oxidation resistance. After secondary coating the samples presented a reddish color due to the formation of iron oxide and poor dielectric property.

Low-temperature sintering behavior of nanocrystalline indium tin oxide prepared from polymer-containing sols

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koroesi, Laszlo, E-mail: l.korosi@chem.u-szeged.hu; Papp, Szilvia; Oszko, Albert

2012-04-15

Highlights: Black-Right-Pointing-Pointer The synthesis of ITO powders and thin films from PVP-containing sols is presented. Black-Right-Pointing-Pointer The nano- and microstructures of ITO are more compact when PVP is used. Black-Right-Pointing-Pointer PVP acts both as a steric stabilizer of the sol and as a pre-sintering agent. Black-Right-Pointing-Pointer The PVP-induced enhanced sintering results in ITO with lower electrical resistance. Black-Right-Pointing-Pointer The surface composition of the ITO films is independent of the initial PVP content. -- Abstract: Indium tin hydroxide (ITH) xerogel powders and thin films with different polyvinylpyrrolidone (PVP) contents (0-22%, w/w) were prepared by a classical sol-gel method. To obtain nanocrystallinemore » indium tin oxide (ITO), the ITH xerogels were calcined at 550 Degree-Sign C. The effect of the initial polymer content on the structure of the ITO powders was studied by means of N{sub 2}-sorption measurements, small-angle X-ray scattering (SAXS), transmission and scanning electron microscopy. The N{sub 2}-sorption measurements revealed that the ITO powders obtained contained micropores and both their porosity and specific surface area decreased with increasing PVP content of the ITH xerogels. The SAXS measurements confirmed the enhanced sintering of the particles in the presence of PVP. The calculated mass fractal dimensions of the ITO powders increased significantly, indicating a significant compaction in structure. The pre-sintered structure could be achieved at relatively low temperature, which induced a significant decreasing (three orders of magnitude) in the electrical resistance of the ITO films.« less

Powder-XRD and (14) N magic angle-spinning solid-state NMR spectroscopy of some metal nitrides.

PubMed

Kempgens, Pierre; Britton, Jonathan

2016-05-01

Some metal nitrides (TiN, ZrN, InN, GaN, Ca3 N2 , Mg3 N2 , and Ge3 N4 ) have been studied by powder X-ray diffraction (XRD) and (14) N magic angle-spinning (MAS) solid-state NMR spectroscopy. For Ca3 N2 , Mg3 N2 , and Ge3 N4 , no (14) N NMR signal was observed. Low speed (νr  = 2 kHz for TiN, ZrN, and GaN; νr  = 1 kHz for InN) and 'high speed' (νr  = 15 kHz for TiN; νr  = 5 kHz for ZrN; νr  = 10 kHz for InN and GaN) MAS NMR experiments were performed. For TiN, ZrN, InN, and GaN, powder-XRD was used to identify the phases present in each sample. The number of peaks observed for each sample in their (14) N MAS solid-state NMR spectrum matches perfectly well with the number of nitrogen-containing phases identified by powder-XRD. The (14) N MAS solid-state NMR spectra are symmetric and dominated by the quadrupolar interaction. The envelopes of the spinning sidebands manifold are Lorentzian, and it is concluded that there is a distribution of the quadrupolar coupling constants Qcc 's arising from structural defects in the compounds studied. Copyright © 2015 John Wiley & Sons, Ltd.

The Conterminous United States Mineral Assessment Program; background information to accompany folio of geologic, geophysical, geochemical, mineral-occurrence, mineral-resource potential, and mineral-production maps of the Charlotte 1 degree x 2 degrees Quadrangle, North Carolina and South Carolina

USGS Publications Warehouse

Gair, Jacob Eugene; Goldsmith, Richard; Daniels, D.L.; Griffitts, W.R.; DeYoung, J.H.; Lee, M.P.

1986-01-01

This Circular and the folio of separately published maps described herein are part of a series of reports compiled under the Conterminous United States Mineral Assessment Program ICUSMAP). The folio on the Charlotte 1 degree ? 2 degree quadrangle, North Carolina and South Carolina, includes (1) a geologic map; (2) four geophysical maps; (3) geochemical maps for metamorphic heavy minerals, copper, lead and artifacts, zinc, gold, tin, beryllium, niobium, tungsten, molybdenum, titanium, cobalt, lithium, barium, antimony-arsenic-bismuth-cadmium, thorium-cerium-monazite, and limonite; (4) mineral-occurrence maps for kyanite-sillimanite-lithium-mica-feldspar-copper-lead-zinc, gold-quartz-barite-fluorite, iron-thorium-tin-niobium, and construction materials-gemstones; (5) mineral-resource potential maps for copper-lead-zinc-combined base metals, gold, tin-tungsten, beryllium-molybdenum-niobium, lithium-kyanite- sillimanitebarite, thorium (monazite)-uranium, and construction materials; and (6) mineral-production maps. The Charlotte quadrangle is mainly within the Piedmont physiographic province and extends from near the Coastal Plain on the southeast into the Blue Ridge province on the northwest for a short distance. Parts of six lithotectonic belts are present--the Blue Ridge, the Inner Piedmont, the Kings Mountain belt, the Charlotte belt, the Carolina slate belt, and the Wadesboro basin. Igneous, metamorphic, and sedimentary rocks are present and range in age from Proterozoic to Mesozoic; alluvial sediments of Quaternary age occur along rivers and larger streams. Rocks of the Blue Ridge include Middle Proterozoic granitoid gneiss intruded by Late Proterozoic granite; Late Proterozoic paragneiss, schist, and other metasedimentary and metavolcaniclastic rocks (Ashe and Grandfather Mountain Formations); Late Proterozoic and Early Cambrian metasedimentary rocks (Chilhowee Group); and Early Cambrian sedimentary rocks (Shady Dolomite). Paleozoic granites intrude the Proterozoic rocks. The Inner Piedmont contains noncarbonate metasedimentary rocks and amphibolite of medium to high metamorphic grades. These rocks are intruded by the Toluca Granite and Henderson Gneiss of Cambrian and Ordovician(?) age. The Charlotte belt consists largely of Late Proterozoic to Late Paleozoic granitic and gabbroic plutonic rocks and intervening enclaves of metasedimentary and metavolcanic rocks. The narrow Kings Mountain belt is located between the Charlotte and the Inner Piedmont belts and contains mainly Late Proterozoic metasedimentary rocks and plutonic rocks similar to those of the Charlotte belt. The Carolina slate belt, flanking the Charlotte belt on the east, contains weakly metamorphosed volcanic and sedimentary rocks. East of this belt, at the southeast corner of the quadrangle, is the Wadesboro basin, which has continental sedimentary rocks of Triassic age. Layered rocks westward from and in the Charlotte belt are complexly folded, are steeply dipping, and in the Blue Ridge and Inner Piedmont are contained within major thrust slices. Rocks of the Carolina slate belt are gently folded. Rocks of the Wadesboro basin occur in downfaulted blocks. The geophysical surveys of the Charlotte quadrangle consisted of Bouguer gravity, aeromagnetic, and aeroradioactivity surveys and used both newly obtained data and information from prior work. The gravity survey disclosed a distinct northeast-trending, northwest-decreasing gradient, which is part of the major gravity gradient that extends the length of the Appalachian Mountains. Granitic plutons of the Charlotte belt, in particular, are marked by gravity lows, and gabbro plutons, by highs. Several of the geologic belts display distinct magnetic character. The aeroradioactivity surveys showed a swath of consistently high gamma-ray intensities along the central part of the Inner Piedmont belt; these high intensities correspond to the so-called monazite belt. Oval patterns of high gamma-ray readi

Facile synthesis of novel two- and three-dimensional coordination polymers containing dialkyltin phosphonate-based tri/tetra-nuclear clusters with appended sulfonate groups.

PubMed

Shankar, Ravi; Jain, Archana; Singh, Atul Pratap; Kociok-Köhn, Gabriele; Molloy, Kieran C

2009-04-20

The coordination-driven self-assemblies of mixed-ligand dialkyltin derivatives, [(Et(2)Sn)(4) (O(2)P(OH)Me)(2)(O(3)PMe)(2)(OSO(2)Et)(2) x 2 H(2)O](n) 1, [(Et(2)Sn)(3)(O(3)PMe)(2)(OSO(2)Me)(2) x CHCl(3)](n) 2, and [(Me(2)Sn)(3)(O(3)PBu(t))(2)(OSO(2)Me)(2) x 2 CHCl(3)](n) 3 have been achieved by reacting the tin precursors, [R(2)Sn(OR(1))(OSO(2)R(1))](n) (R = Et, R(1) = Et (1a), Me (2a); R = Me, R(1) = Me (3a)) with an equimolar amount of methylphosphonic/t-butylphosphonic acid under mild conditions (rt, 8 h, CH(2)Cl(2)). These have been characterized by IR and multinuclear ((1)H, (13)C, (31)P, and (119)Sn) NMR spectroscopy as well as single crystal X-ray diffraction. The asymmetric unit of 1 is composed of a tetranuclear, Sn(4)(mu(2)-PO(2))(2)(mu(3)-PO(3))(2) core bearing an appended ethanesulfonate group on each terminal tin (Sn2) atom and two P(OH)...O hydrogen bonded water molecules. The ladder-like structural motif thus formed is extended into one-dimensional polymeric chains by virtue of bridging bidentate mode of the sulfonate groups. These chains are linked by O-H...O(S) hydrogen bonds involving H(2)O molecules and oxygen atoms of the sulfonate groups. The asymmetric units of 2 and 3 are composed of trinuclear tin clusters with a Sn(3)(mu(3)-PO(3))(2) core and two dangling methanesulfonate groups which are covalently bonded to the tin centers. The construction of three-dimensional self-assemblies is effected by variable bonding modes (mu(2), mu(3) in 2; mu(2) in 3) of the methanesulfonate groups. Both the structural motifs possess five- and six-coordinated tin atoms and form rectangular channels which are occupied by CHCl(3) molecules.

Transposable elements as a molecular evolutionary force

NASA Technical Reports Server (NTRS)

Fedoroff, N. V.

1999-01-01

This essay addresses the paradoxes of the complex and highly redundant genomes. The central theses developed are that: (1) the distinctive feature of complex genomes is the existence of epigenetic mechanisms that permit extremely high levels of both tandem and dispersed redundancy; (2) the special contribution of transposable elements is to modularize the genome; and (3) the labilizing forces of recombination and transposition are just barely contained, giving a dynamic genetic system of ever increasing complexity that verges on the chaotic.

A Study of Melt Inclusions in Tin-Mineralized Granites From Zinnwald, Germany

NASA Astrophysics Data System (ADS)

Sookdeo, C. A.; Webster, J. D.; Eschen, M. L.; Tappen, C. M.

2001-12-01

We have analyzed silicate melt inclusions from drill core samples from the eastern Erzgebirge region, Germany, to investigate magmatic-hydrothermal and mineralizing processes in compositionally evolved, tin-bearing granitic magmas. Silicate melt inclusions are small blebs of glass that are trapped or locked within phenocrysts and may contain high concentrations of volatiles that usually leave magma via degassing. Quartz phenocrysts were carefully hand picked from crushed samples of albite-, zinnwaldite- +/- lepidolite-bearing granitic dikes from Zinnwald and soaked in cold dilute HF to remove any attached groundmass. The cleaned phenocrysts were loaded into precious metal capsules with several drops of immersion oil to create a reducing environment at high temperature. The quartz-bearing capsules were inserted into quartz glass tubes, loaded into a furnace for heating at temperatures of 1025\\deg and 1050\\deg C (1atm) for periods of 20 to 30 hours, and subsequently the inclusions were quenched to glass. The inclusions were analyzed for major and minor elements (including F, Cl, and P) by electron microprobe and for H2O, trace elements, and ore elements by ion microprobe. The melt inclusion compositions are similar to that of the whole-rock sample from which the quartz separates were extracted. The average melt inclusion and whole-rock compositions are peraluminous, high in silica and rare alkalis, and low in MgO, CaO, FeO, MnO, and P2O5. Unlike the whole-rock sample, the melt inclusions contain from 0.5 to more than 4 wt.% F. The Cl contents of the inclusions are variable and range from hundreds of ppm to several thousand ppm. The variable and strong enrichments in F of the melt inclusions may correlate with (Na2O/Na2O+K2O) in the inclusions which is consistent with crystal fractionation of feldspars which drives the residual melt to increasing Na contents. Overall, the compositions of these melt inclusions are different from melt inclusions extracted from the highly peraluminous, tin-mineralized granites of the western Erzgebirge region. The latter represent extreme compositional evolution of P- and F-rich magmas. The inclusions from the albite-, zinnwaldite-, +/- lepidolite-bearing granitic dikes of Zinnwald are more similar, compositionally, to those in tin-mineralized rhyolites of Mexico and New Mexico; the Erzgebirge dike melt inclusions container comparatively greater abundances of Li, Sn, and F, however.

The role of a trigeminal sensory nucleus in the initiation of locomotion.

PubMed

Buhl, Edgar; Roberts, Alan; Soffe, Stephen R

2012-05-15

While we understand how stimuli evoke sudden, ballistic escape responses, like fish fast-starts, a precise pathway from sensory stimulation to the initiation of rhythmic locomotion has not been defined for any vertebrate. We have now asked how head skin stimuli evoke swimming in hatchling frog tadpoles. Whole-cell recordings and dye filling revealed a nucleus of ∼20 trigeminal interneurons (tINs) in the hindbrain, at the level of the auditory nerve, with long, ipsilateral, descending axons. Stimulation of touch-sensitive trigeminal afferents with receptive fields anywhere on the head evoked large, monosynaptic EPSPs (∼5-20 mV) in tINs, at mixed AMPAR/NMDAR synapses. Following stimuli sufficient to elicit swimming, tINs fired up to six spikes, starting 4-8 ms after the stimulus. Paired whole-cell recordings showed that tINs produce small (∼2-6 mV), monosynaptic, glutamatergic EPSPs in the hindbrain reticulospinal neurons (descending interneurons, dINs) that drive swimming. Modelling suggested that summation of EPSPs from 18-24 tINs can make 20-50% of dINs fire. We conclude that: brief activity in a few sensory afferents is amplified by recruitment of many tINs; these relay summating excitation to hindbrain reticulospinal dINs; dIN firing then initiates activity for swimming on the stimulated side. During fictive swimming, tINs are depolarised and receive rhythmic inhibition but do not fire. Our recordings demonstrate a neuron-by-neuron pathway from head skin afferents to the reticulospinal neurons and motoneurons that drive locomotion in a vertebrate. This direct pathway, which has an important amplifier function, implies a simple origin for the complex routes to initiate locomotion in higher vertebrates.

The role of a trigeminal sensory nucleus in the initiation of locomotion

PubMed Central

Buhl, Edgar; Roberts, Alan; Soffe, Stephen R

2012-01-01

While we understand how stimuli evoke sudden, ballistic escape responses, like fish fast-starts, a precise pathway from sensory stimulation to the initiation of rhythmic locomotion has not been defined for any vertebrate. We have now asked how head skin stimuli evoke swimming in hatchling frog tadpoles. Whole-cell recordings and dye filling revealed a nucleus of ∼20 trigeminal interneurons (tINs) in the hindbrain, at the level of the auditory nerve, with long, ipsilateral, descending axons. Stimulation of touch-sensitive trigeminal afferents with receptive fields anywhere on the head evoked large, monosynaptic EPSPs (∼5–20 mV) in tINs, at mixed AMPAR/NMDAR synapses. Following stimuli sufficient to elicit swimming, tINs fired up to six spikes, starting 4–8 ms after the stimulus. Paired whole-cell recordings showed that tINs produce small (∼2–6 mV), monosynaptic, glutamatergic EPSPs in the hindbrain reticulospinal neurons (descending interneurons, dINs) that drive swimming. Modelling suggested that summation of EPSPs from 18–24 tINs can make 20–50% of dINs fire. We conclude that: brief activity in a few sensory afferents is amplified by recruitment of many tINs; these relay summating excitation to hindbrain reticulospinal dINs; dIN firing then initiates activity for swimming on the stimulated side. During fictive swimming, tINs are depolarised and receive rhythmic inhibition but do not fire. Our recordings demonstrate a neuron-by-neuron pathway from head skin afferents to the reticulospinal neurons and motoneurons that drive locomotion in a vertebrate. This direct pathway, which has an important amplifier function, implies a simple origin for the complex routes to initiate locomotion in higher vertebrates. PMID:22393253

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

40 CFR 721.10140 - Phosphoric acid, tin (2+) salt (2:3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Phosphoric acid, tin (2+) salt (2:3... Specific Chemical Substances § 721.10140 Phosphoric acid, tin (2+) salt (2:3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as phosphoric acid, tin (2...

Pb-free electronics: from nanotechnology to combinatorial materials science

NASA Astrophysics Data System (ADS)

Diaz Gonzalez, Alfredo J.

The elimination of lead (Pb) from the electronics industry due to a government directive caused problems on the manufacturing and use of electronic components. The current alloys used to attach components have a significant higher processing temperature (~30-40°C) that those containing Pb. The higher processing temperatures cause damage to the electronic components; printed circuit boards (PCB) and represents an increase in energetic costs for the manufacurer. Tin whiskers are out-of-plane structures that grow from tin (Sn) plated surfaces and cause short circuits and metal vapor arc. The electrical connection of components to the PCB relies on leads that are close to each other and are manufactured from tin-plated copper. Materials have shown a tendency to modify their bulk properties depending on powder particle size. Nanoparticle's coalescence temperature tends to decrease as particle size decreases. Exploiting this behavior, a nanoparticle based solder paste has been developed for attaching electronic components at a lower processing temperature to avoid thermally induced damage and reduce energy consumption. Tin nanoparticles were successfully synthesized via a wet chemistry route using tin (II) chloride dihydrated (metal precursor), 1,10-Phenanthroline (surfactant), and sodium borohydride (reducing agent). A flux system was developed based on Ethylene Glycol. Results showed acceptable coalescence of the non-capped nanoparticles at temperatures as low as 200°C with a processing time of 20 minutes. Synthesized nanoparticles with capping agent required higher flux content thus resulting in a poor metallic load paste. A reduction in processing temperature of approximately 40°C have been found when comparing the developed solder paste with typical SAC lead-free solders (~240°C). The electrical behavior was found to be an order of magnitude below that of bulk tin. Compositional libraries have been developed in an attempt to screen, via a high through-put method, alloys that are prone to tin whiskers growth. These libraries are samples containing a range of sub-samples with varying compositions within it than can be processed simultaneously. Using sputtering, a physical vapor deposition technique, a gradient composed of Ag-Cu was deposited over a Sn-plated Cu substrate. After reflow, the growth mechanism of the whiskers was accelerated using the IEC60068-82-2 standard. SEM and EDS analysis was used to charac-terize the growth of the tin whiskers at different elemental compositions. The gradients found across the samples are in accordance with the theoretical geometrical spacing. Tin whiskers were found on control samples, whereas almost all elemental compositions showed mitigation or elimination of the whiskers. This combinatorial material science methodology proved to be an efficient and fast screening method for the plating materials selection process in Pb-free electronics.

Properties of Resistive Hydrogen Sensors as a Function of Additives of 3 D-Metals Introduced in the Volume of Thin Nanocrystalline SnO2 Films

NASA Astrophysics Data System (ADS)

Sevast'yanov, E. Yu.; Maksimova, N. K.; Potekaev, A. I.; Sergeichenko, N. V.; Chernikov, E. V.; Almaev, A. V.; Kushnarev, B. O.

2017-11-01

Analysis of the results of studying electrical and gas sensitive characteristics of the molecular hydrogen sensors based on thin nanocrystalline SnO2 films coated with dispersed Au layers and containing Au+Ni and Au+Co impurities in the bulk showed that the characteristics of these sensors are more stable under the prolonged exposure to hydrogen in comparison with Au/SnO2:Sb, Au films modified only with gold. It has been found that introduction of the nickel and cobalt additives increases the band bending at the grain boundaries of tin dioxide already in freshly prepared samples, which indicates an increase in the density Ni of the chemisorbed oxygen. It is important that during testing, the band bending eφs at the grain boundaries of tin dioxide additionally slightly increases. It can be assumed that during crystallization of films under thermal annealing, the 3d-metal atoms in the SnO2 volume partially segregate on the surface of microcrystals and form bonds with lattice oxygen, the superstoichiometric tin atoms are formed, and the density Ni increases. If the bonds of oxygen with nickel and cobalt are stronger than those with tin, then, under the prolonged tests, atomic hydrogen will be oxidized not by lattice oxygen, but mainly by the chemisorbed one. In this case, stability of the sensors' characteristics increases.

Methods for chemical recovery of non-carrier-added radioactive tin from irradiated intermetallic Ti-Sb targets

DOEpatents

Lapshina, Elena V [Troitsk, RU; Zhuikov, Boris L [Troitsk, RU; Srivastava, Suresh C [Setauket, NY; Ermolaev, Stanislav V [Obninsk, RU; Togaeva, Natalia R [Obninsk, RU

2012-01-17

The invention provides a method of chemical recovery of no-carrier-added radioactive tin (NCA radiotin) from intermetallide TiSb irradiated with accelerated charged particles. An irradiated sample of TiSb can be dissolved in acidic solutions. Antimony can be removed from the solution by extraction with dibutyl ether. Titanium in the form of peroxide can be separated from tin using chromatography on strong anion-exchange resin. In another embodiment NCA radiotin can be separated from iodide solution containing titanium by extraction with benzene, toluene or chloroform. NCA radiotin can be finally purified from the remaining antimony and other impurities using chromatography on silica gel. NCA tin-117m can be obtained from this process. NCA tin-117m can be used for labeling organic compounds and biological objects to be applied in medicine for imaging and therapy of various diseases.

Inelastic proton scattering and particle-vibration coupling in /sup 115/Sn, /sup 117/Sn, and /sup 119/Sn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fleming, D.G.; Becchetti, F.D.; Flynn, E.R.

Inelastic proton scattering on the stable odd-A tin isotopes /sup 115/Sn, /sup 117/Sn, and /sup 119/Sn has been carried out at 18 MeV on isotope separated targets. Angular distributions were not obtained but, nevertheless, the individual spectra reveal a large number of strongly populated states in the energy region of the known octupole strength of the even-A nuclei, permitting several new (tentative) 5/2/sup -/,7/2/sup -/ spin assignments. General comparisons are made of the observed relative strengths with those obtained from other reactions populating the same final states, revealing a complex nuclear structure in the odd-A tins which is not understoodmore » theoretically.« less

Substrate-insensitive atomic layer deposition of plasmonic titanium nitride films

DOE PAGES

Yu, Ing-Song; Cheng, Hsyi-En; Chang, Chun-Chieh; ...

2017-02-06

The plasmonic properties of titanium nitride (TiN) films depend on the type of substrate when using typical deposition methods such as sputtering. We show atomic layer deposition (ALD) of TiN films with very weak dependence of plasmonic properties on the substrate, which also suggests the prediction and evaluation of plasmonic performance of TiN nanostructures on arbitrary substrates under a given deposition condition. Our results also observe that substrates with more nitrogen-terminated (N-terminated) surfaces will have significant impact on the deposition rate as well as the film plasmonic properties. Furthermore, we illustrate that the plasmonic properties of ALD TiN films canmore » be tailored by simply adjusting the deposition and/or post-deposition annealing temperatures. These characteristics and the capability of conformal coating make ALD TiN films on templates ideal for applications that require the fabrication of complex 3D plasmonic nanostructures.« less

Unexpected Trimerization of Pyrazine in the Coordination Sphere of Low-Valent Titanocene Fragments.

PubMed

Jung, Thomas; Beckhaus, Rüdiger; Klüner, Thorsten; Höfener, Sebastian; Klopper, Wim

2009-08-11

The titanium mediated trimerization of pyrazine leads to the formation of a tris-chelate complex employing a 4a,4b,8a,8b,12a,12b-hexahydrodiyprazino[2,3-f:2',3'-h]quinoxaline ligand (HATH6, 3). The driving force in the formation of the (Cp*2Ti)3(HATH6) complex 2 is attributed to the formation of six Ti-N bonds. We show that density functional theory (DFT) fails to predict quantitatively correct results. Therefore, post-Hartree-Fock methods, such as second-order Møller-Plesset perturbation theory (MP2), in combination with coupled-cluster (CC) methods must be used. Both MP2 and CCSD(T) levels of theory provide endothermic trimerization energies, showing that the plain pyrazine trimer is not stable with respect to decomposition into its monomers. Complete basis set (CBS) results for the MP2 level of theory were computed using explicitly correlated wave functions. With these, we estimate the CCSD(T) CBS limit of the hypothetical trimerization energy to be +0.78 eV. Thus, the trimerization is facilitated by the formation of six Ti-N bonds with a calculated formation energy of -1.32 eV per bond.

A CityGML Extension for Handling Very Large Tins

NASA Astrophysics Data System (ADS)

Kumar, K.; Ledoux, H.; Stoter, J.

2016-10-01

In addition to buildings, the terrain forms an important part of a 3D city model. Although in GIS terrains are usually represented with 2D grids, TINs are also increasingly being used in practice. One example is 3DTOP10NL, the 3D city model covering the whole of the Netherlands, which stores the relief with a constrained TIN containing more than 1 billion triangles. Due to the massive size of such datasets, the main problem that arises is: how to efficiently store and maintain them? While CityGML supports the storage of TINs, we argue in this paper that the current solution is not adequate. For instance, the 1 billion+ triangles of 3DTOP10NL require 686 GB of storage space with CityGML. Furthermore, the current solution does not store the topological relationships of the triangles, and also there are no clear mechanisms to handle several LODs. We propose in this paper a CityGML extension for the compact representation of terrains. We describe our abstract and implementation specifications (modelled in UML), and our prototype implementation to convert TINs to our CityGML structure. It increases the topological relationships that are explicitly represented, and allows us to compress up to a factor of ∼ 25 in our experiments with massive real-world terrains (more than 1 billion triangles).

Growth, intermixing, and surface phase formation for zinc tin oxide nanolaminates produced by atomic layer deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hägglund, Carl, E-mail: carl.hagglund@angstrom.uu.se; Grehl, Thomas; Brongersma, Hidde H.

2016-03-15

A broad and expanding range of materials can be produced by atomic layer deposition at relatively low temperatures, including both oxides and metals. For many applications of interest, however, it is desirable to grow more tailored and complex materials such as semiconductors with a certain doping, mixed oxides, and metallic alloys. How well such mixed materials can be accomplished with atomic layer deposition requires knowledge of the conditions under which the resulting films will be mixed, solid solutions, or laminated. The growth and lamination of zinc oxide and tin oxide is studied here by means of the extremely surface sensitivemore » technique of low energy ion scattering, combined with bulk composition and thickness determination, and x-ray diffraction. At the low temperatures used for deposition (150 °C), there is little evidence for atomic scale mixing even with the smallest possible bilayer period, and instead a morphology with small ZnO inclusions in a SnO{sub x} matrix is deduced. Postannealing of such laminates above 400 °C however produces a stable surface phase with a 30% increased density. From the surface stoichiometry, this is likely the inverted spinel of zinc stannate, Zn{sub 2}SnO{sub 4}. Annealing to 800 °C results in films containing crystalline Zn{sub 2}SnO{sub 4}, or multilayered films of crystalline ZnO, Zn{sub 2}SnO{sub 4}, and SnO{sub 2} phases, depending on the bilayer period.« less

The study of aluminium anodes for high power density Al/air batteries with brine electrolytes

NASA Astrophysics Data System (ADS)

Nestoridi, Maria; Pletcher, Derek; Wood, Robert J. K.; Wang, Shuncai; Jones, Richard L.; Stokes, Keith R.; Wilcock, Ian

Aluminium alloys containing small additions of both tin (∼0.1 wt%) and gallium (∼0.05 wt%) are shown to dissolve anodically at high rates in sodium chloride media at room temperatures; current densities >0.2 A cm -2 can be obtained at potentials close to the open circuit potential, ∼-1500 mV versus SCE. The tin exists in the alloys as a second phase, typically as ∼1 μm inclusions (precipitates) distributed throughout the aluminium structure, and anodic dissolution occurs to form pits around the tin inclusions. Although the distribution of the gallium in the alloy could not be established, it is also shown to be critical in the formation of these pits as well as maintaining their activity. The stability of the alloys to open circuit corrosion and the overpotential for high rate dissolution, both critical to battery performance, are shown to depend on factors in addition to elemental composition; both heat treatment and mechanical working influence the performance of the alloy. The correlation between alloy performance and their microstructure has been investigated.

Reconnaissance geochemical survey of Al Jurdhawiyah and Wadi al Jarir quadrangles, sheets 25/42 D and 25/42 C, Kingdom of Saudia Arabia

USGS Publications Warehouse

Samater, Rashid M.

1983-01-01

A reconnaissance wadi-sediment geochemical survey was conducted in the Al Jurdhawiyah (sheet 28/42 D) and Wadi al Jarir (sheet 2G/42 C) quadrangles in order to identify anomalies potentially related to mineralized rock. Sieved bulk-sediment fractions and pan concentrates were created from the original samples collected from wadis in the two quadrangles. A semiquantitative 30-element spectrographic analysis was completed on both the sieved bulk-sediment fraction and the pan concentrate of each sample. The results were statistically analyzed in an attempt to identify anomalous regions. Anomaly threshold values were calculated for most elements; the threshold value of an element in a data set is defined as the geometric mean value plus two standard deviations. The Bald al Jimalah West tin-tungsten deposit (MODS 02661) in the southern part of the Al Jurdhawiyah quadrangle was identified by one pan-concentrate sample containing anomalous concentrations of tin and tungsten. Samples near the Bald al Jimalah East ancient lead-zinc-silver mines (MODS 00960) contain strongly anomalous concentrations of tin and lead and to a lesser extent of tungsten and copper. Both of these regions and other regions containing anomalous concentrations of certain elements are recommended for additional studies. A comparison of results obtained from sieved bulk-sediment fractions and pan concentrates indicates that the latter is the better medium for these geochemical investigations.

Pourbaix Diagrams at Elevated Temperatures A Study of Zinc and Tin

NASA Astrophysics Data System (ADS)

Palazhchenko, Olga

Metals in industrial settings such as power plants are often subjected to high temperature and pressure aqueous environments, where failure to control corrosion compromises worker and environment safety. For instance, zircaloy (1.2-1.7 wt.% Sn) fuel rods are exposed to aqueous 250-310 °C coolant in CANDU reactors. The Pourbaix (EH-pH) diagram is a plot of electrochemical potential versus pH, which shows the domains of various metal species and by inference, corrosion susceptibility. Elevated temperature data for tin +II and tin +IV species were obtained using solid-aqueous phase equilibria with the respective oxides, in a batch vessel with in-situ pH measurement. Solubilities, determined via spectroscopic techniques, were used to calculate equilibrium constants and the Gibbs energies of Sn complexes for E-pH diagram construction. The SnOH3+ and Sn(OH )-5 species were incorporated, for the first time, into the 298.15 K and 358.15 K diagrams, with novel Go values determined at 358.15 K. Key words: Pourbaix diagrams, EH-pH, elevated temperatures, solubility, equilibrium, metal oxides, hydrolysis, redox potential, pH, thermochemical data, tin, zinc, zircaloy, corrosion, passivity.

Peroxide induced tin oxide coating of graphene oxide at room temperature and its application for lithium ion batteries.

PubMed

Sladkevich, S; Gun, J; Prikhodchenko, P V; Gutkin, V; Mikhaylov, A A; Novotortsev, V M; Zhu, J X; Yang, D; Hng, H H; Tay, Y Y; Tsakadze, Z; Lev, O

2012-12-07

We describe a new, simple and low-temperature method for ultra-thin coating of graphene oxide (GO) by peroxostannate, tin oxide or a mixture of tin and tin oxide crystallites by different treatments. The technique is environmentally friendly and does not require complicated infrastructure, an autoclave or a microwave. The supported peroxostannate phase is partially converted after drying to crystalline tin oxide with average, 2.5 nm cassiterite crystals. Mild heat treatment yielded full coverage of the reduced graphene oxide by crystalline tin oxide. Extensive heat treatment in vacuum at >500 °C yielded a mixture of elemental tin and cassiterite tin oxide nanoparticles supported on reduced graphene oxide (rGO). The usefulness of the new approach was demonstrated by the preparation of two types of lithium ion anodes: tin oxide-rGO and a mixture of tin oxide and tin coated rGO composites (SnO(2)-Sn-rGO). The electrodes exhibited stable charge/discharge cyclability and high charging capacity due to the intimate contact between the conductive graphene and the very small tin oxide crystallites. The charging/discharging capacity of the anodes exceeded the theoretical capacity predicted based on tin lithiation. The tin oxide coated rGO exhibited higher charging capacity but somewhat lower stability upon extended charge/discharge cycling compared to SnO(2)-Sn-rGO.

Comparison of several analytical methods for the determination of tin in geochemical samples as a function of tin speciation

USGS Publications Warehouse

Kane, J.S.; Evans, J.R.; Jackson, J.C.

1989-01-01

Accurate and precise determinations of tin in geological materials are needed for fundamental studies of tin geochemistry, and for tin prospecting purposes. Achieving the required accuracy is difficult because of the different matrices in which Sn can occur (i.e. sulfides, silicates and cassiterite), and because of the variability of literature values for Sn concentrations in geochemical reference materials. We have evaluated three methods for the analysis of samples for Sn concentration: graphite furnace atomic absorption spectrometry (HGA-AAS) following iodide extraction, inductively coupled plasma atomic emission spectrometry (ICP-OES), and energy-dispersive X-ray fluorescence (EDXRF) spectrometry. Two of these methods (HGA-AAS and ICP-OES) required sample decomposition either by acid digestion or fusion, while the third (EDXRF) was performed directly on the powdered sample. Analytical details of all three methods, their potential errors, and the steps necessary to correct these errors were investigated. Results showed that similar accuracy was achieved from all methods for unmineralized samples, which contain no known Sn-bearing phase. For mineralized samples, which contain Sn-bearing minerals, either cassiterite or stannous sulfides, only EDXRF and fusion ICP-OES methods provided acceptable accuracy. This summary of our study provides information which helps to assure correct interpretation of data bases for underlying geochemical processes, regardless of method of data collection and its inherent limitations. ?? 1989.

Charge storage in oxygen deficient phases of TiO2: defect Physics without defects.

PubMed

Padilha, A C M; Raebiger, H; Rocha, A R; Dalpian, G M

2016-07-01

Defects in semiconductors can exhibit multiple charge states, which can be used for charge storage applications. Here we consider such charge storage in a series of oxygen deficient phases of TiO2, known as Magnéli phases. These Magnéli phases (TinO2n-1) present well-defined crystalline structures, i.e., their deviation from stoichiometry is accommodated by changes in space group as opposed to point defects. We show that these phases exhibit intermediate bands with an electronic quadruple donor transitions akin to interstitial Ti defect levels in rutile TiO2. Thus, the Magnéli phases behave as if they contained a very large pseudo-defect density: ½ per formula unit TinO2n-1. Depending on the Fermi Energy the whole material will become charged. These crystals are natural charge storage materials with a storage capacity that rivals the best known supercapacitors.

DEM Based Modeling: Grid or TIN? The Answer Depends

NASA Astrophysics Data System (ADS)

Ogden, F. L.; Moreno, H. A.

2015-12-01

The availability of petascale supercomputing power has enabled process-based hydrological simulations on large watersheds and two-way coupling with mesoscale atmospheric models. Of course with increasing watershed scale come corresponding increases in watershed complexity, including wide ranging water management infrastructure and objectives, and ever increasing demands for forcing data. Simulations of large watersheds using grid-based models apply a fixed resolution over the entire watershed. In large watersheds, this means an enormous number of grids, or coarsening of the grid resolution to reduce memory requirements. One alternative to grid-based methods is the triangular irregular network (TIN) approach. TINs provide the flexibility of variable resolution, which allows optimization of computational resources by providing high resolution where necessary and low resolution elsewhere. TINs also increase required effort in model setup, parameter estimation, and coupling with forcing data which are often gridded. This presentation discusses the costs and benefits of the use of TINs compared to grid-based methods, in the context of large watershed simulations within the traditional gridded WRF-HYDRO framework and the new TIN-based ADHydro high performance computing watershed simulator.

Contrasting Granite Metallogeny through the Zircon Record: A Case Study from Myanmar.

PubMed

Gardiner, Nicholas J; Hawkesworth, Chris J; Robb, Laurence J; Whitehouse, Martin J; Roberts, Nick M W; Kirkland, Christopher L; Evans, Noreen J

2017-04-07

Granitoid-hosted mineral deposits are major global sources of a number of economically important metals. The fundamental controls on magma metal fertility are tectonic setting, the nature of source rocks, and magma differentiation. A clearer understanding of these petrogenetic processes has been forged through the accessory mineral zircon, which has considerable potential in metallogenic studies. We present an integrated zircon isotope (U-Pb, Lu-Hf, O) and trace element dataset from the paired Cu-Au (copper) and Sn-W (tin) magmatic belts in Myanmar. Copper arc zircons have juvenile εHf (+7.6 to +11.5) and mantle-like δ 18 O (5.2-5.5‰), whereas tin belt zircons have low εHf (-7 to -13) and heavier δ 18 O (6.2-7.7‰). Variations in zircon Hf and U/Yb reaffirm that tin belt magmas contain greater crustal contributions than copper arc rocks. Links between whole-rock Rb/Sr and zircon Eu/Eu* highlight that the latter can monitor magma fractionation in these systems. Zircon Ce/Ce* and Eu/Eu* are sensitive to redox and fractionation respectively, and here are used to evaluate zircon sensitivity to the metallogenic affinity of their host rock. Critical contents of Sn in granitic magmas, which may be required for the development of economic tin deposits, are marked by zircon Eu/Eu* values of ca. ≤0.08.

Canopy architectural and physiological characterization of near-isogenic wheat lines differing in the tiller inhibition gene tin.

PubMed

Moeller, Carina; Evers, Jochem B; Rebetzke, Greg

2014-01-01

Tillering is a core constituent of plant architecture, and influences light interception to affect plant and crop performance. Near-isogenic lines (NILs) varying for a tiller inhibition (tin) gene and representing two genetic backgrounds were investigated for tillering dynamics, organ size distribution, leaf area, light interception, red: far-red ratio, and chlorophyll content. Tillering ceased earlier in the tin lines to reduce the frequencies of later primary and secondary tillers compared to the free-tillering NILs, and demonstrated the genetically lower tillering plasticity of tin-containing lines. The distribution of organ sizes along shoots varied between NILs contrasting for tin. Internode elongation commenced at a lower phytomer, and the peduncle was shorter in the tin lines. The flag leaves of tin lines were larger, and the longest leaf blades were observed at higher phytomers in the tin than in free-tillering lines. Total leaf area was reduced in tin lines, and non-tin lines invested more leaf area at mid-canopy height. The tiller economy (ratio of seed-bearing shoots to numbers of shoots produced) was 10% greater in the tin lines (0.73-0.76) compared to the free-tillering sisters (0.62-0.63). At maximum tiller number, the red: far-red ratio (light quality stimulus that is thought to induce the cessation of tillering) at the plant-base was 0.18-0.22 in tin lines and 0.09-0.11 in free-tillering lines at levels of photosynthetic active radiation of 49-53% and 30-33%, respectively. The tin lines intercepted less radiation compared to their free-tillering sisters once genotypic differences in tiller numbers had established, and maintained green leaf area in the lower canopy later into the season. Greater light extinction coefficients (k) in tin lines prior to, but reduced k after, spike emergence indicated that differences in light interception between NILs contrasting in tin cannot be explained by leaf area alone but that geometric and optical canopy properties contributed. The careful characterization of specifically-developed NILs is refining the development of a physiology-based model for tillering to improve understanding of the value of architectural traits for use in cereal improvement.

Structure of dental gallium alloys.

PubMed

Herø, H; Simensen, C J; Jørgensen, R B

1996-07-01

The interest in gallium alloys as a replacement for amalgam has increased in recent years due to the risk of environmental pollution from amalgam. Alloy powders with compositions close to those for alloys of amalgam are mixed with a liquid gallium alloy. The mix is condensed into a prepared cavity in much the same way as for amalgam. The aim of the present work was to study the structure of: (1) two commercial alloy powders containing mainly silver, tin and copper, and (2) the phases formed by mixing these powders with a liquid alloy of gallium, indium and tin. One of the alloy powders contained 9 wt% palladium. Cross-sections of cylindrical specimens made by these gallium mixes were investigated by scanning electron microscopy, energy dispersive spectroscopy and X-ray diffraction. Discrete grains of the following phases were found to be present in both gallium alloys: hexagonal Ag2Ga, tetragonal Cu(Pd)Ga2, cubic Ag9In4 and tetragonal beta-Sn. Indications of hexagonal or orthorhombic Ag2Sn were found in the remaining, unreacted alloy particles. In the palladium-containing alloy the X-ray reflections indicate a minor fraction of cubic Cu9Ga4 in addition to the Cu(Pd)Ga2 phase. Particles of beta-Sn are probably precipitated because Sn-Ga phases cannot be formed according to the binary phase diagram.

Mandrake--an ancient herbal discovered.

PubMed

Sutcliffe, Terry

2008-09-01

I recently purchased the pharmacy container (illustrated) from an antique dealer friend who had kept three of these tins for 20 years intending to convert them into lamp bases. Fortunately I persuaded him to sell them to me rather than being hacked up. The other two are labeled 'BETT. RT PUL' 'LUNGWORT'. (All three are similarly painted, lidded tins and all stand 13 inches high, with a diameter of seven inches.) The label 'MANDRAKERT' immediately conjured up two impressions, firstly my boyhood reading of Mandrake the magician comics, and secondly a strong interest to research the story behind this 19th century tin's mystical contents.

VO2 /TiN Plasmonic Thermochromic Smart Coatings for Room-Temperature Applications.

PubMed

Hao, Qi; Li, Wan; Xu, Huiyan; Wang, Jiawei; Yin, Yin; Wang, Huaiyu; Ma, Libo; Ma, Fei; Jiang, Xuchuan; Schmidt, Oliver G; Chu, Paul K

2018-03-01

Vanadium dioxide/titanium nitride (VO 2 /TiN) smart coatings are prepared by hybridizing thermochromic VO 2 with plasmonic TiN nanoparticles. The VO 2 /TiN coatings can control infrared (IR) radiation dynamically in accordance with the ambient temperature and illumination intensity. It blocks IR light under strong illumination at 28 °C but is IR transparent under weak irradiation conditions or at a low temperature of 20 °C. The VO 2 /TiN coatings exhibit a good integral visible transmittance of up to 51% and excellent IR switching efficiency of 48% at 2000 nm. These unique advantages make VO 2 /TiN promising as smart energy-saving windows. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis of thin film containing 4-amino-1,2,4-triazole iron(II) complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Onggo, Djulia, E-mail: djulia@Chem.itb.ac.id

The Iron(II) complex with 4-amino-1,2,4 triazole (NH{sub 2}-trz) ligand has potential applications as smart material since the compounds show a distinct color change from lilac at low temperature to colorless at high temperature. The lilac color of the complex represent the diamagnetic low spin state while the colorless correspond to the paramagnetic high spin state of iron(II). The transition between the two states could be tuned by changing the anionic group. Generally, the complex was synthesized directly from aqueous solution of iron(II) salt with considerable amounts of NH{sub 2}-trz solution produced solid powder compound. For application as an electronic molecularmore » device, the complex should be obtained as a thin film. The transparent [Fe(NH{sub 2}trz){sub 3}]-Nafion film has been successfully obtained, however, no anion variation can be produced since the nafion is an anionic resin. In this work, the [Fe(NH{sub 2}trz){sub 3}]-complexes with several anions have been synthesized inside nata de coco membrane that commonly used as a medium for deposition metal nano-particles. After drying the membrane containing the complex became a thin film. At room temperature, the film containing iron(II) complexes of sulphate and nitrate salts show lilac color, similar to that of the original complexes in the powder form. On heating, the color of the complex film changed to colorless and this color change was observed reversibly. In contrast, the films containing perchlorate and tetrafluoroborate iron(II) complexes are colorless at room temperature and changed to lilac on cooling. The significant color changing of the iron(II)complexes in the nata de coco film can be used for demonstration thermo chromic effect of smart materials with relatively small amount of the compounds.« less

KENNEDY SPACE CENTER, FLA. - Valerie Cassanto, with Instrumentation Technology Associates, Inc., examines closely the container containing one of the experiments carried on mission STS-107. Several experiments were found during the search for Columbia debris. Included in the Commercial ITA Biomedical Experiments payload on mission STS-107 are urokinase cancer research, microencapsulation of drugs, the Growth of Bacterial Biofilm on Surfaces during Spaceflight (GOBBSS), and tin crystal formation.

NASA Image and Video Library

2003-05-06

KENNEDY SPACE CENTER, FLA. - Valerie Cassanto, with Instrumentation Technology Associates, Inc., examines closely the container containing one of the experiments carried on mission STS-107. Several experiments were found during the search for Columbia debris. Included in the Commercial ITA Biomedical Experiments payload on mission STS-107 are urokinase cancer research, microencapsulation of drugs, the Growth of Bacterial Biofilm on Surfaces during Spaceflight (GOBBSS), and tin crystal formation.

Regeneration of polyborazylene

DOEpatents

Davis, Benjamin L.; Gordon, John C.

2010-12-07

Method of producing ammonia borane, comprising providing polyborazylene; digesting the polyborazylene with a dithiol-containing agent to produce a boro-sulfide compound and a byproduct; converting the byproduct to the boro-sulfide product of step (b) by reaction with a first alkyl-tin hydride; and, converting the boro-sulfide compound produced in steps (b) and (c) to ammonia borane by reaction with a second alkyl-tin hydride.

High Temperature Reactions of Uranium Dioxide with Various Metal Oxides

DTIC Science & Technology

1956-02-20

manganese, nickel , lead, and tin. Subtracting the total of these impurities from the oxygen remainder would give a more nearly 1:2 uranium -oxygen ratio. The...Astin, Dire~ctor High -Temperature Reactions of Uranium Dioxide With Various Metal Oxides Acceson For NTIS CRAWI DTfC TAB Unannounced D JustifiCation...1 2. The uranium -oxygen system ------------------------------------- 1 3. Binary systems containing

Nitrogen spatial heterogeneity influences diversity following restoration in a ponderosa pine forest, Montana.

PubMed

Gundale, Michael J; Metlen, Kerry L; Fiedler, Carl E; DeLuca, Thomas H

2006-04-01

The resource heterogeneity hypothesis (RHH) is frequently cited in the ecological literature as an important mechanism for maintaining species diversity. The RHH has rarely been evaluated in the context of restoration ecology in which a commonly cited goal is to restore diversity. In this study we focused on the spatial heterogeneity of total inorganic nitrogen (TIN) following restoration treatments in a ponderosa pine (Pinus ponderosa)/Douglas-fir (Pseudotsuga menziesii) forest in western Montana, USA. Our objective was to evaluate relationships between understory species richness and TIN heterogeneity following mechanical thinning (thin-only), prescribed burning (burn-only), and mechanical thinning with prescribed burning (thin/burn) to discern the ecological and management implications of these restoration approaches. We employed a randomized block design, with three 9-ha replicates of each treatment and an untreated control. Within each treatment, we randomly established a 20 x 50 m (1000 m2) plot in which we measured species richness across the entire plot and in 12 1-m(2) quadrats randomly placed within each larger plot. Additionally, we measured TIN from a grid consisting of 112 soil samples (0-5 cm) in each plot and computed standard deviations as a measure of heterogeneity. We found a correlation between the net increase in species richness and the TIN standard deviations one and two years following restoration treatments, supporting RHH. Using nonmetric multidimensional scaling ordination and chi-squared analysis, we found that high and low TIN quadrats contained different understory communities in 2003 and 2004, further supporting RHH. A comparison of restoration treatments demonstrated that thin/burn and burn-only treatments created higher N heterogeneity relative to the control. We also found that within prescribed burn treatments, TIN heterogeneity was positively correlated with fine-fuel consumption, a variable reflecting burn severity. These findings may lead to more informed restoration decisions that consider treatment effects on understory diversity in ponderosa pine/Douglas-fir ecosystems.

XRF measurements of tin, copper and zinc in antifouling paints coated on leisure boats.

PubMed

Ytreberg, Erik; Bighiu, Maria Alexandra; Lundgren, Lennart; Eklund, Britta

2016-06-01

Tributyltin (TBT) and other organotin compounds have been restricted for use on leisure boats since 1989 in the EU. Nonetheless, release of TBT is observed from leisure boats during hull maintenance work, such as pressure hosing. In this work, we used a handheld X-ray Fluorescence analyser (XRF) calibrated for antifouling paint matrixes to measure tin, copper and zinc in antifouling paints coated on leisure boats in Sweden. Our results show that over 10% of the leisure boats (n = 686) contain >400 μg/cm(2) of tin in their antifouling coatings. For comparison, one layer (40 μm dry film) of a TBT-paint equals ≈ 800 μg Sn/cm(2). To our knowledge, tin has never been used in other forms than organotin (OT) in antifouling paints. Thus, even though the XRF analysis does not provide any information on the speciation of tin, the high concentrations indicate that these leisure boats still have OT coatings present on their hull. On several leisure boats we performed additional XRF measurements by progressively scraping off the top coatings and analysing each underlying layer. The XRF data show that when tin is detected, it is most likely present in coatings close to the hull with several layers of other coatings on top. Thus, leaching of OT compounds from the hull into the water is presumed to be negligible. The risk for environmental impacts arises during maintenance work such as scraping, blasting and high pressure hosing activities. The data also show that many boat owners apply excessive paint layers when following paint manufacturers recommendations. Moreover, high loads of copper were detected even on boats sailing in freshwater, despite the more than 20 year old ban, which poses an environmental risk that has not been addressed until now. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

77 FR 3725 - Proposed Significant New Use Rules on Certain Chemical Substances; Extension of Comment Period

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-25

... chemical substances rutile, tin zinc, calcium-doped (CAS No. 389623-01- 2) and rutile, tin zinc, sodium... substances rutile, tin zinc, calcium- doped (CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (CAS No...

Thermal Studies of New Precursors to Indium-tin Oxides for Use as Sensor Materials in the Detection of NO(x)

NASA Technical Reports Server (NTRS)

Goldsby, J. C.; Kacik, T.; Hockensmith, C. M.

1999-01-01

Control of combustion product emissions in both sub and super-sonic jet engines can be facilitated by measurement of NO(x) levels with metal oxide sensors, In2O3, metal-doped SnO2, and SnO, (as well as other materials) show resistivity changes in the presence of NO(x), but often their sensitivity, stability, and selectivity are low. This study was designed to develop new synthetic pathways to precursors that produce high purity, two phase In2O3-SnO2. The precursors were formed by complexation of tin with any oxide ligands to give the ammonium salt (NH4). Thermal studies of these precursors were carried out by thermal gravimetry (TG) and differential scanning calorimetry (DSC). Further studies by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR) were also conducted.

Influence of alloying elements on friction and wear of copper

NASA Technical Reports Server (NTRS)

Buckley, D. H.

1972-01-01

The friction and wear characteristics were determined for copper binary alloys containing 10 atomic percent aluminum, silicon, indium, and tin. A ternary alloy containing 10 atomic percent aluminum and 5 atomic percent silicon was also examined. The effectiveness of each of the alloying elements aluminum and silicon were very effective in reducing friction. Silicon, however, also reduced wear appreciably. With lubrication, silicon, indium, and tin were all effective alloying elements in reducing friction and wear from values obtained for copper. Silicon was the most effective single element in reducing friction and wear in dry sliding and with lubrication.

Preliminary report on geology, geochemical exploration, and biogeochemical exploration of the Red Mountain stockwork, Yellow Pine District, Valley County, Idaho

USGS Publications Warehouse

Leonard, B.F.; Erdman, James A.

1983-01-01

New exploration targets for gold, molybdenum, tungsten, and tin are indicated by the systematic distribution of metals in soil and plants of the Red Mountain stockwork and its environs. The stockwork is built of countless quartz veins and veinlets, extensively argillized and containing sparsely disseminated gold, pyrite, arsenoDyrite, Dyrrhotite, fluorite, and other minerals. The stockwork developed along the outer ring-fracture zone of the Eocene Quartz Creek cauldron where subsidence strain, unrelieved by radial faulting, produced internal deformation and intense small-scale fracturing in rocks of the Idaho batholith. The stockwork, cropping out as a fault-bounded polygon 2,700 ft long and 2,000 ft wide, contains (underlies?) a large, virtually barren quartz body 1,350 ft long and 350 ft wide. Deformed, shattered granite flanks and presumably underlies the stockwork, which may plunge southward beneath inclusion-bearing granodiorite and alaskite of the Idaho batholith suite. Narrow dikes of rhyolite and latite radiate from two centers within the quartz body. Many dikes and small bosses of rhyolite and latite intrude stockwork and granite. The radial habit of some dikes and the high frequency of small intrusives concentrated within the sericite and kaolinite alteration zones suggest that a Tertiary porphyry is concealed beneath the mountain. Clay-mineral alteration zones mapped in residual soil extend far outward from the stockwork. Valleys filled with Quaternary deposits bound the stockwork-granite complex on the east, north, and west, effectively concealing elements of a crudely elliptical substructure that differs from the fault-dissected, mappable part of the complex. Metal anomalies in soil of the 3,600-ft x 8,400-ft gridded area are mostly weak and small. In contrast, metal anomalies in plants are strong, large, and consistent with the inference of a concealed elliptical substructure that may be hoodlike and may contain more than one mineralized zone. Gold in ashed sapwood of douglas-fir (Pseudotsuga menziesii) indicates a major gold anomaly, peak value 14.2 ppm Au, on inclusion-bearing granodiorite in an unprospected area south of the exposed stockwork. Locally, the gold anomaly is accompanied by a sizable tin anomaly, peak value 100 ppm Sn, in douglas-fir. Molybdenum in ashed leaves of beargrass (Xerophyllum tenax), peak value >500 ppm Mo, indicates extensive anomalies within a 2-milelong semi-elliptical belt of Mo values exceeding the 20 ppm median. Most of the belt is on valley fill, but the southern segment of it, near the major gold anomaly, is mainly on inclusion-bearing granodiorite. Here, where beargrass is sparse, the peak value of Mo in beargrass drops to 70 ppm. Where beargrass is absent, ashed leaves of sedge (Carex geyeri) have anomalous values of 100 ppm Mo. An additional target for molybdenum is indicated by molybdenite from the inaccessible Dart of the main adit. The molybdenite, seen only in dump specimens, is in weakly silicified granite that may underlie part of the stockwork. The source body of the molybdenite is blind, and no clue to it is given by samples of soil or plants. Just north of the major gold anomaly, 2 ppm values of W in beargrass coincide approximately with a tungsten anomaly in soil (peak value 22 ppm W) in an area of float containing disseminated scheelite in weakly silicified inclusion-bearing granodiorite. Other areas of 2 ppm W values in beargrass are nearly coextensive with the Moin-beargrass anomalies on Quaternary deposits of Quartz Creek valley. Some of the target areas for gold, molybdenum, tungsten, and tin have not been circumscribed by our sampling.

Methicillin-susceptible Staphylococcus aureus endocarditis isolates are associated with clonal complex 30 genotype and a distinct repertoire of enterotoxins and adhesins.

PubMed

Nienaber, Juhsien J C; Sharma Kuinkel, Batu K; Clarke-Pearson, Michael; Lamlertthon, Supaporn; Park, Lawrence; Rude, Thomas H; Barriere, Steve; Woods, Christopher W; Chu, Vivian H; Marín, Mercedes; Bukovski, Suzana; Garcia, Patricia; Corey, G Ralph; Korman, Tony; Doco-Lecompte, Thanh; Murdoch, David R; Reller, L Barth; Fowler, Vance G

2011-09-01

Using multinational collections of methicillin-susceptible Staphylococcus aureus (MSSA) isolates from infective endocarditis (IE) and soft tissue infections (STIs), we sought to (1) validate the finding that S. aureus in clonal complex (CC) 30 is associated with hematogenous complications and (2) test the hypothesis that specific genetic characteristics in S. aureus are associated with infection severity. IE and STI isolates from 2 cohorts were frequency matched by geographic origin. Isolates underwent spa typing to infer CC and multiplex polymerase chain reaction for presence of virulence genes. 114 isolate pairs were genotyped. IE isolates were more likely to be CC30 (19.5% vs 6.2%; P = .005) and to contain 3 adhesins (clfB, cna, map/eap; P < .0001 for all) and 5 enterotoxins (tst, sea, sed, see, and sei; P ≤ .005 for all). CC30 isolates were more likely to contain cna, tst, sea, see, seg, and chp (P < .05 for all). MSSA IE isolates were significantly more likely to be CC30 and to possess a distinct repertoire of virulence genes than MSSA STI isolates from the same region. The genetic basis of this association requires further study.

Enhancement of mechanical properties of 123 superconductors

DOEpatents

Balachandran, Uthamalingam

1995-01-01

A composition and method of preparing YBa.sub.2 Cu.sub.3 O.sub.7-x superconductor. Addition of tin oxide containing compounds to YBCO superconductors results in substantial improvement of fracture toughness and other mechanical properties without affect on T.sub.c. About 5-20% additions give rise to substantially improved mechanical properties.

76 FR 17997 - Privacy Act of 1974, as Amended

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-31

..., support good jobs, and increase U.S. competitiveness. As required by 5 U.S.C. 552a(r), a report of a new... certification. The records may contain taxpayer names and Taxpayer Identification Numbers (TIN) (social security... new and cost-saving therapies, support good jobs, and increase U.S. competitiveness. (2) Disclose...

Biotransformation of tributyltin to tin in freshwater river-bed sediments contaminated by an organotin release

USGS Publications Warehouse

Landmeyer, J.E.; Tanner, T.L.; Watt, B.E.

2004-01-01

The largest documented release of organotin compounds to a freshwater river system in the United States occurred in early 2000 in central South Carolina. The release consisted of an unknown volume of various organotin compounds such tetrabutyltin (TTBT), tributyltin (TBT), tetraoctyltin (TTOT), and trioctyl tin (TOT) and resulted in a massive fish kill and the permanent closures of a municipal wastewater treatment plant and a local city's only drinking-water intake. Initial sampling events in 2000 and 2001 indicated that concentrations of the ecologically toxic TTBT and TBT were each greater than 10 000 ??g/kg in surface-water bed sediments in depositional areas, such as lakes and beaver ponds downstream of the release. Bed-sediment samples collected between 2001 and 2003, however, revealed a substantial decrease in bed-sediment organotin concentrations and an increase in concentrations of degradation intermediate compounds. For example, in bed sediments of a representative beaver pond located about 1.6 km downstream of the release, total organotin concentrations [the sum of TTBT, TBT, and the TBT degradation intermediates dibutyltin (DBT) and monobutyltin (MBT)] decreased from 38 670 to 298 ??g/kg. In Crystal Lake, a large lake about 0.4 km downstream from the beaver pond, total organotin concentrations decreased from 28 300 to less than 5 ??g/kg during the same time period. Moreover, bed-sediment inorganic tin concentrations increased from pre-release levels of less than 800 to 32 700 ??g/kg during this time. These field data suggest that the released organotin compounds, such as TBT, are being transformed into inorganic tin by bed-sediment microbial processes. Microcosms were created in the laboratory that contained bed sediment from the two sites and were amended with tributyltin (as tributyltin chloride) under an ambient air headspace and sacrificially analyzed periodically for TBT, the biodegradation intermediates DBT and MBT, and tin. TBT concentrations decreased faster [half-life (t1/2) = 28 d] in the organic-rich sediments (21.5%) that characterized the beaver pond as compared to the slower (t1/2 = 78 d) degradation rate in the sandy, organic-poor, sediments (0.43%) of Crystal Lake. Moreover, the concentration of inorganic tin increased in microcosms containing bed sediments from both locations. These field and laboratory results suggest that biotransformation of the released organotins, in particular the ecologically detrimental TBT, does occur in this fresh surface-water system impacted with high concentrations of neat organotin compounds.

Silver-tin alloys and amalgams: electrochemical considerations.

PubMed

Mueller, H J

1980-01-01

The corrosion potential and anodic polarization profiles of a representative number of silver-tin alloys and their corresponding amalgams in a physiological solution were determined and compared to their microstructures. For the alloys with tin-content greater than 27%(wt) and for all amalgams, the corrosion process is related to the attack of free tin for the alloys and to the gamma-2 tin for the amalgams. The gamma-2 concentration in the amalgams increases with an increase in tin-content. For alloys with tin-content less than 27%, the corrosion process is even more restricted than for the process observed with pure silver. From a developed theory based upon the potential-time and polarization results, association of the O2 reduction process on a SnO cathodic film to an intermediate specie of H2O2 is made. The rate of H2O2 decomposition on a SnO surface in a four electron process is thought to control the O2 reduction overvoltage. The O2 reduction overvoltage decreases with increases in the silver-content of the amalgam, particularily seen with the 8 and 12% tin compositions. Due to the polarization induced corrosion process, a phase with high silver and high mercury concentrations was observed over the unreacted particles.

Leaded electronic waste is a possible source material for lead-contaminated jewelry.

PubMed

Weidenhamer, Jeffrey D; Clement, Michael L

2007-10-01

Highly leaded jewelry, often imported from China, remains widely available in the United States. Leaded electronic waste is exported from the United States to several Asian countries where solder is recovered and circuit boards are stripped of parts in small workshops. To assess whether electronic waste is being recycled into the jewelry, lead, tin and copper content of highly leaded jewelry samples were determined by atomic absorption spectrometry. Sixteen jewelry items previously determined to contain 20-80% lead by weight were analyzed. Samples were digested in nitric acid for analysis of lead and copper, and in aqua regia for analysis of tin. Six samples contained significant amounts of tin, from 20.8% to 29.9% by weight. In addition, copper was a significant minor component of five of these samples (up to 4% by weight). Copper (present at 10-40% by weight in circuit boards) was shown to rapidly move into heated lead-tin solder. The combined lead-tin-copper content of these six items ranges from 93.5% to 100%, suggestive of a solder-based source material. These results are consistent with the hypothesis that recycled circuit board solders are being used to produce some of the heavily leaded imported jewelry sold in the United States. Should this hypothesis be substantiated, it suggests that environmental policies to protect children's health must address both proper recycling of source materials as well as restrictions of the lead content in consumer goods.

Highly sensitive SnO2 sensor via reactive laser-induced transfer

PubMed Central

Palla Papavlu, Alexandra; Mattle, Thomas; Temmel, Sandra; Lehmann, Ulrike; Hintennach, Andreas; Grisel, Alain; Wokaun, Alexander; Lippert, Thomas

2016-01-01

Gas sensors based on tin oxide (SnO2) and palladium doped SnO2 (Pd:SnO2) active materials are fabricated by a laser printing method, i.e. reactive laser-induced forward transfer (rLIFT). Thin films from tin based metal-complex precursors are prepared by spin coating and then laser transferred with high resolution onto sensor structures. The devices fabricated by rLIFT exhibit low ppm sensitivity towards ethanol and methane as well as good stability with respect to air, moisture, and time. Promising results are obtained by applying rLIFT to transfer metal-complex precursors onto uncoated commercial gas sensors. We could show that rLIFT onto commercial sensors is possible if the sensor structures are reinforced prior to printing. The rLIFT fabricated sensors show up to 4 times higher sensitivities then the commercial sensors (with inkjet printed SnO2). In addition, the selectivity towards CH4 of the Pd:SnO2 sensors is significantly enhanced compared to the pure SnO2 sensors. Our results indicate that the reactive laser transfer technique applied here represents an important technical step for the realization of improved gas detection systems with wide-ranging applications in environmental and health monitoring control. PMID:27118531

Cell proteins bind to multiple sites within the 5' untranslated region of poliovirus RNA.

PubMed Central

del Angel, R M; Papavassiliou, A G; Fernández-Tomás, C; Silverstein, S J; Racaniello, V R

1989-01-01

The 5' noncoding region of poliovirus RNA contains sequences necessary for translation and replication. These functions are probably carried out by recognition of poliovirus RNA by cellular and/or viral proteins. Using a mobility-shift electrophoresis assay and 1,10-phenanthroline/Cu+ footprinting, we demonstrate specific binding of cytoplasmic factors with a sequence from nucleotides 510-629 within the 5' untranslated region (UTR). Complex formation was also observed with a second sequence (nucleotides 97-182) within the 5' UTR. These two regions of the 5' UTR appear to be recognized by distinct cell factors as determined by competition analysis and the effects of ionic strength on complex formation. However, both complexes contain eukaryotic initiation factor 2 alpha, as revealed by their reaction with specific antibody. Images PMID:2554308

78 FR 16048 - Proposed Collection; Comment Request for e-Services Registration TIN Matching-Application and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-13

...-Services Registration TIN Matching--Application and Screens for TIN Matching Interactive AGENCY: Internal...(c)(2)(A)). Currently, the IRS is soliciting comments concerning e- Services registration TIN matching--application and screens for TIN matching interactive. DATES: Written comments should be received...

75 FR 5854 - Proposed Collection; Comment Request for e-Services Registration TIN Matching-Application and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-04

...-Services Registration TIN Matching--Application and Screens for TIN Matching Interactive AGENCY: Internal...(c)(2)(A)). Currently, the IRS is soliciting comments concerning e- Services Registration TIN Matching--Application and Screens for TIN Matching Interactive. DATES: Written comments should be received...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2014 CFR

2014-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

26 CFR 1.6050H-0 - Table of contents.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., 1989. (i) Failure to file return or to furnish statement. (ii) Failure to furnish TIN. (iii) Failure to...) Failure to furnish TIN. (iii) Failure to include correct information. (f) Requirement to request and to obtain TIN. (1) In general. (2) Manner of requesting TIN. (g) Effective date. (1) In general. (2) Points...

76 FR 68512 - Carolina Power & Light Company; H. B. Robinson Steam Electric Plant, Unit 2; Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-04

... (~1 percent). The elimination of tin has resulted in superior corrosion resistance and reduced irradiation-induced growth relative to both standard zircaloy (1.7 percent tin) and low-tin zircaloy (1.2 percent tin). The addition of niobium increases ductility, which is desirable to avoid brittle failures...

Design and synthesis of inorganic/organic hybrid electrochemical materials

NASA Astrophysics Data System (ADS)

Harreld, John H.

An ambient pressure method for drying sol-gel materials is developed to synthesize high porosity (80--90%), high surface area vanadium oxide and silica aerogel materials (150--300 and 1000 m2/g for vanadium pentoxide and silica, respectively). The synthesis approach uses liquid exchange to replace the pore fluid with a low surface tension, nonpolar solvent which reduces the capillary pressures developed during drying. The Good-Girifalco interaction parameter is used to calculate pore stresses resulting from drying silica gels from various liquids. Vanadium oxide/polypyrrole hybrid aerogels are prepared using three strategies. These approaches focus on either sequential or consecutive polymerization of the inorganic and organic networks. Microcomposite aerogels are synthesized by encapsulating a dispersion of preformed polypyrrole in a vanadium pentoxide gel. In the second approach, pyrrole is polymerized and doped within the pore volume of preformed vanadium pentoxide gel. When the inorganic and organic precursors are polymerized simultaneously, the resulting gels exhibited a nanometer scaled microstructure with homogeneous distributions of either phases. Through this route, a suitable microstructure and composition for a lithium secondary battery cathode is obtained. Lithiated aerogels of hydrated nickel, cobalt, and mixed nickel-cobalt oxides are synthesized from lithium hydroxide and transition metal acetate precursors. The XRD analyses indicate that the nickel containing gels exhibit a lithium deficiency (less than 1 Li/transition metal. By increasing the concentration of the lithium precursor the lithium content in nickel oxides is increased, and additional base solution is no longer required to catalyze gelation. A non-hydrolytic sol-gel approach is utilized to create tin oxide and tin-aluminum binary oxide aerogels with high porosity (90%) and high surface area (300 m2/g). XRD data from single phase tin oxide aerogel indicates the growth of SnO2 crystallites between 150--400°C in air, accompanied by a reduction in surface area (30 m2/g). Heated tin oxide aerogel exhibits comparable reversible specific capacity (390 mAh/g) as that of commercial SnO2 (420 mAh/g). Amorphous tin oxide aerogel is stabilized to higher temperatures when aluminum oxide is incorporated into the structure. The tin oxide phase remains electrochemically active towards lithium insertion and exhibits excellent reversibility during cycling.

40 CFR 437.11 - Effluent limitations attainable by the application of the best practicable control technology...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 1.45 Silver 0.120 0.0351 Tin 0.409 0.120 Titanium 0.0947 0.0618 Vanadium 0.218 0.0662 Zinc 2.87 0.641 1 mg/L (ppm). 2 Within the range 6 to 9. (b) The following in-plant limitations apply to metal-bearing wastewater containing cyanide: In-Plant Limitations Regulatedparameter Maximum daily 1 Maximum...

Evaluation of the suitability of tin slag in cementitious materials: Mechanical properties and Leaching behaviour

NASA Astrophysics Data System (ADS)

Rustandi, Andi; Wafa' Nawawi, Fuad; Pratesa, Yudha; Cahyadi, Agung

2018-01-01

Tin slag, a by-product of tin production has been used in cementitious application. The present investigation focuses on the suitability of tin slag as primary component in cement and as component that substitute some amount of Portland Cement. The tin slags studied were taken from Bangka, Indonesia. The main contents of the tin slag are SiO2, Al2O3, and Fe2O3 according to the XRF investigation. The aim of this article was to study the mechanical behaviour (compressive strength), microstructure and leaching behaviour of tin slag blended cement. This study used air-cooled tin slag that had been passed through 400# sieve to replace Portland Cement with ratio 0, 10, 20, 30, 40 by weight. Cement pastes and tin slag blended cement pastes were prepared by using water/cement ratio (W/C) of 0.40 by weight and hydrated for various curing ages of 3, 7, 14 days The microstructure of the raw tin slag was investigated using Scanning Electron Microscope (SEM). The phase composition of each cement paste was investigated using X-ray Diffraction (XRD). The aim of the leachability test was to investigate the environmental impacts of tin slag blended cement product in the range 4-8 pH by using static pH-dependent leaching test. The result show that the increase of the tin slag content decreasing the mortar compressive strength at early ages. The use of tin slag in cement provide economic benefits for all related industries.

Structural characterization of metal complexes in aqueous solutions: a XAS study of stannous fluoride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alsina, Marco A.; Gaillard, Jean-François

The identity and structure of tin(ii)-fluoride complexes formed in aqueous solutions are determined by combining X-ray absorption spectroscopy, thermodynamic modeling and quantum mechanical calculations.

Amorphous tin-cadmium oxide films and the production thereof

DOEpatents

Li, Xiaonan; Gessert, Timothy A

2013-10-29

A tin-cadmium oxide film having an amorphous structure and a ratio of tin atoms to cadmium atoms of between 1:1 and 3:1. The tin-cadmium oxide film may have an optical band gap of between 2.7 eV and 3.35 eV. The film may also have a charge carrier concentration of between 1.times.10.sup.20 cm.sup.-3 and 2.times.10.sup.20 cm.sup.-3. The tin cadmium oxide film may also exhibit a Hall mobility of between 40 cm.sup.2V.sup.-1 s.sup.-1 and 60 cm.sup.2V.sup.-1 s.sup.-1. Also disclosed is a method of producing an amorphous tin-cadmium oxide film as described and devices using same.

Ursolic Acid Hydrazide Based Organometallic Complexes: Synthesis, Characterization, Antibacterial, Antioxidant and Docking Studies

NASA Astrophysics Data System (ADS)

Jabeen, Muafia; Ahmad, Sajjad; Shahid, Khadija; Sadiq, Abdul; Rashid, Umer

2018-03-01

In the current research work,eleven metal complexes were synthesized from the hydrazide derivative of ursolic acid. Metal complexes of tin, antimony and iron were synthesized and characterized by FT-IR and NMR spectroscopy. The antibacterial and antioxidant activities were performed for these complexes, which revealed that the metal complexes synthesized are more potent than their parent compounds. We observed that antioxidant activity showed by triphenyltin complex was significant and least activity have been shown by antimony trichloride complex.The synthesized metal complexes were then evaluated against two Gram-negative and two Gram-positive bacterial strains. Triphenyl tin complex emerged as potent antibacterial agent with MIC value of 8 μg/ml each against Shigellaspp, S. typhi and S. aureus. While, the MIC value againstS. pneumoniae is 4 μg/ml.Computational docking studies were carried out on molecular targets to interpret the results of antioxidant and antibacterial activities. Based on the results, it may be inferred that the metal complexes of ursolic acid are more active as compared to the parent drug and may be proved for some other pharmacological potential by further analysis.

Synthesis and surface chemistry of high quality wurtzite and kesterite Cu2ZnSnS4 nanocrystals using tin(II) 2-ethylhexanoate as a new tin source.

PubMed

Gabka, Grzegorz; Bujak, Piotr; Gryszel, Maciej; Ostrowski, Andrzej; Malinowska, Karolina; Zukowska, Grazyna Z; Agnese, Fabio; Pron, Adam; Reiss, Peter

2015-08-21

A novel synthesis method for the preparation of Cu2ZnSnS4 nanocrystals is presented using a liquid precursor of tin, namely tin(II) 2-ethylhexanoate, which yields small and nearly monodisperse NCs either in the kesterite or in the wurtzite phase depending on the sulfur source (elemental sulfur in oleylamine vs. dodecanethiol).

An investigation of the oxidation behaviour of zirconium alloys using isotopic tracers and high resolution SIMS

NASA Astrophysics Data System (ADS)

Yardley, Sean S.; Moore, Katie L.; Ni, Na; Wei, Jang Fei; Lyon, Stuart; Preuss, Michael; Lozano-Perez, Sergio; Grovenor, Chris R. M.

2013-11-01

High resolution secondary ion mass spectrometry (SIMS) analysis has been used to study the oxidation mechanisms when commercial low tin ZIRLO™Low tin ZIRLO™ is a trademark of Westinghouse Electric Company LLC in the United States and may be registered in other countries throughout the world. Unauthorized use is strictly prohibited.1 and Zircaloy 4 materials are exposed to corroding environments containing both 18O and 2H isotopes. Clear evidence has been shown for different characteristic distributions of 18O before and after the kinetic transitions, and this behaviour has been correlated with the development of porosity in the oxide which allows the corroding medium to penetrate locally to the metal/oxide interface.

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2014 CFR

2014-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2013 CFR

2013-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

26 CFR 1.6050S-0 - Table of contents.

Code of Federal Regulations, 2012 CFR

2012-04-01

... penalties for failures to include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN. (4) Failure to furnish TIN. (f) Effective date. § 1.6050S-2TElectronic... include a correct TIN. (i) In general. (ii) Acting in a responsible manner. (iii) Manner of soliciting TIN...

77 FR 42990 - Significant New Use Rules on Certain Chemical Substances

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

... Toxic Substances Control Act (TSCA) for the chemical substances rutile, tin zinc, calcium-doped (CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (CAS No. 389623-07-8) which were the subject of..., tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (PMN P...

Influence of silicon oxide on the performance of TiN bottom electrode in phase change memory

NASA Astrophysics Data System (ADS)

Gao, Dan; Liu, Bo; Xu, Zhen; Wang, Heng; Xia, Yangyang; Wang, Lei; Zhu, Nanfei; Li, Ying; Zhan, Yipeng; Song, Zhitang; Feng, Songlin

2016-10-01

The stability of TiN which is the preferred bottom electrode contact (BEC) of phase change memory (PCM) due to its low thermal conductivity and suitable electrical conductivity, is very essential to the reliability of PCM devices. In this work, in order to investigate the effect of high aspect ratio process (HARP) SiO2 on the performance of TiN, both TiN/SiO2, TiN/SiN thin films and TiN BEC device structures are analyzed. By combining transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDS), we found that the TiN would be oxidized after the deposition of HARP SiO2 and there exist a thin ( 4 nm) oxidation interfacial layer between TiN and SiO2. Electrical measurements were performed on the 1R PCM test-key die with 7 nm and 10 nm BEC-only cells. The statistical initial resistances of BEC have wide distribution and it is confirmed that the non-uniform oxidation of TiN BEC affects the astringency of the resistance of TiN BEC. The experimental results help to optimize the process of TiN BEC, and SiN is recommended as a better choice as the linear layer.

Species identification in mixed tuna samples with next-generation sequencing targeting two short cytochrome b gene fragments.

PubMed

Kappel, Kristina; Haase, Ilka; Käppel, Christine; Sotelo, Carmen G; Schröder, Ute

2017-11-01

Conventional Sanger sequencing of PCR products is the gold standard for species authentication of seafood products. However, this method is inappropriate for the analysis of products that might contain mixtures of species, such as tinned tuna. The purpose of this study was to test whether next-generation sequencing (NGS) can be a solution for the authentication of mixed products. Nine tuna samples containing mixtures of up to four species were prepared and subjected to an NGS approach targeting two short cytochrome b gene (cytb) fragments on the Illumina MiSeq platform. Sequence recovery was precise and admixtures of as low as 1% could be identified, depending on the species composition of the mixtures. Duplicate samples as well as two individual NGS runs produced very similar results. A first test of three commercial tinned tuna samples indicated the presence of different species in the same tin, although this is forbidden by EU law. Copyright © 2017 Elsevier Ltd. All rights reserved.

An ecotoxicological study on tin- and bismuth-catalysed PDMS based coatings containing a surface-active polymer.

PubMed

Pretti, Carlo; Oliva, Matteo; Mennillo, Elvira; Barbaglia, Martina; Funel, Marco; Reddy Yasani, Bhaskar; Martinelli, Elisa; Galli, Giancarlo

2013-12-01

Novel films were prepared by condensation curing reaction of a poly(dimethyl siloxane) (PDMS) matrix with bismuth neodecanoate and dibutyltin diacetate catalysts. An ecotoxicological study was performed on the leachates of the coatings using the bacterium Vibrio fischeri, the unicellular alga Dunaliella tertiolecta, the crustacean Artemia salina and the fish Sparus aurata (larvae) as testing organisms. A copper-based self-polishing commercial paint was also tested as reference. The results showed that the tin-catalysed coatings and the copper paint were highly toxic against at least two of the four test organisms, whereas bismuth-catalysed coatings did not show any toxic effect. Moreover, the same biological assessment was also carried out on PDMS coatings containing a surface-active fluorinated polymer. The toxicity of the entire polymeric system resulted only from the tin catalyst used for the condensation curing reaction, as the bismuth catalysed coatings incorporating the surface-active polymer remained atoxic toward all the tested organisms. © 2013 Elsevier Inc. All rights reserved.

Enhancement of mechanical properties of 123 superconductors

DOEpatents

Balachandran, U.

1995-04-25

A composition and method are disclosed of preparing YBa{sub 2}Cu{sub 3}O{sub 7{minus}x} superconductor. Addition of tin oxide containing compounds to YBCO superconductors results in substantial improvement of fracture toughness and other mechanical properties without affect on T{sub c}. About 5-20% additions give rise to substantially improved mechanical properties.

Laboratory Transmission of Venezuelan Equine Encephalomyelitis Virus by the Tick Hyalomma Truncatum

DTIC Science & Technology

1994-01-01

equine On day 21 after infestation of the first guinea-pig, none encephalomyelitis virus by the tick of 95 unfed nv mphs sampled contained virus...Epi/ootic strains oft Venezuelan equine encephalo- nymphs [minimum infection rate =2 200 1% I"( 1 contained inveliti. \\EE’ virus Alp/tavirus. family...Togaviridae virus mean titre= 102 1 1PFU ’. About 200 unfed nymphs ý:iuse serious disease tin horse % and humans throughout were placed on a guinea-pig at

Synthesis of Tetraphenylstannacyclopentadienes (Stannoles). II. Derivatives and Adducts of 1,1-Dihalo-2,3,4,5-tetraphenylstannoles.

DTIC Science & Technology

1981-04-15

products (4-bromo-l,2,3,4-tetraphenylbutadienyl)tin tribromide o (4-iodo-l,2,3,4-tetraphenylbutadienyl)tin triiodide. Even gentle chlorination of...hexaphenyistannole by elemental chlorine cleaves the ring tin-carbon bonds to form cis-cis-l ,4-dichloro-l ,2 ,3 ,4-tetraphenylbutadiene-l, 3 and diphenyltin... chlorination of hexaphenylstannole by elemental chlorine cleaves the ring tin-carbon bonds to form cis- cis-l,4-dichloro-l,2,3,4-tetraphenylbutadiene-1,3

Role of point defects and HfO2/TiN interface stoichiometry on effective work function modulation in ultra-scaled complementary metal-oxide-semiconductor devices

NASA Astrophysics Data System (ADS)

Pandey, R. K.; Sathiyanarayanan, Rajesh; Kwon, Unoh; Narayanan, Vijay; Murali, K. V. R. M.

2013-07-01

We investigate the physical properties of a portion of the gate stack of an ultra-scaled complementary metal-oxide-semiconductor (CMOS) device. The effects of point defects, such as oxygen vacancy, oxygen, and aluminum interstitials at the HfO2/TiN interface, on the effective work function of TiN are explored using density functional theory. We compute the diffusion barriers of such point defects in the bulk TiN and across the HfO2/TiN interface. Diffusion of these point defects across the HfO2/TiN interface occurs during the device integration process. This results in variation of the effective work function and hence in the threshold voltage variation in the devices. Further, we simulate the effects of varying the HfO2/TiN interface stoichiometry on the effective work function modulation in these extremely-scaled CMOS devices. Our results show that the interface rich in nitrogen gives higher effective work function, whereas the interface rich in titanium gives lower effective work function, compared to a stoichiometric HfO2/TiN interface. This theoretical prediction is confirmed by the experiment, demonstrating over 700 meV modulation in the effective work function.

Bismuth-, Tin-, and Lead-Containing Metal-Organic Materials: Synthesis, Structure, Photoluminescence, Second Harmonic Generation, and Ferroelectric Properties

NASA Astrophysics Data System (ADS)

Wibowo, Arief Cahyo

Metal-Organic Materials (MOMs) contain metal moieties and organic ligands that combine to form discrete (e.g. metal-organic polyhedra, spheres or nanoballs, metal-organic polygons) or polymeric structures with one-, two-, or three-dimensional periodicities that can exhibit a variety of properties resulting from the presence of the metal moieties and/or ligand connectors in the structure. To date, MOMs with a range of functional attributes have been prepared, including record-breaking porosity, catalytic properties, molecular magnetism, chemical separations and sensing ability, luminescence and NLO properties, multiferroic, ferroelectric, and switchable molecular dielectric properties. We are interested in synthesizing non-centrosymmetric MOM single crystals possessing one of the ten polar space groups required for non-linear optical properties (such as second harmonic generation) and ferroelectric applications. This thesis is divided into two main parts: materials with optical properties, such as photoluminescence and materials for targeted applications such as second harmonic generation and ferroelectric properties. This thesis starts with an introduction describing material having centrosymmetric, non-polar space groups, single crystals structures and their photoluminescence properties. These crystals exhibit very interesting and rare structures as well as interesting photoluminescence properties. Chapters 2-5 of this thesis focus on photoluminescent properties of new MOMs, and detail the exploratory research involving the comparatively rare bismuth, lead, and tin coordination polymers. Specifically, the formation of single white-light emitting phosphors based on the combination of bismuth or lead with pyridine-2,5-dicarboxylate is discussed (Chapter 2). The observation of a new Bi2O2 layer and a new Bi4O 3 chain in bismuth terephthalate-based coordination polymers is presented in Chapter 3, while the formation of diverse structures of tin-based coordination polymer ranging from 1D supramolecular structures to true 3D coordination polymers is covered in Chapter 4. The observation of a new 2D Kagome lattice and unique layered perovskite-type bismuth-based coordination polymers and their photoluminescence properties is the focus of Chapter 5. In chapters 6 and 7, a successful approach to implement our novel hybrid strategy for synthesizing enantiomerically pure single crystals consisting of Second Order Jahn Teller (SOJT)-possessing main group metal cations, specifically bismuth and tin, and homochiral ligands or unsymmetric ligands is discussed. The new MOMs with polar space groups exhibit second harmonic generation and have potential for ferroelectric properties.

Accuracy of iodine removal using dual-energy CT with or without a tin filter: an experimental phantom study.

PubMed

Kawai, Tatsuya; Takeuchi, Mitsuru; Hara, Masaki; Ohashi, Kazuya; Suzuki, Hirochika; Yamada, Kiyotaka; Sugimura, Yuya; Shibamoto, Yuta

2013-10-01

The effects of a tin filter on virtual non-enhanced (VNE) images created by dual-energy CT have not been well evaluated. To compare the accuracy of VNE images between those with and without a tin filter. Two different types of columnar phantoms made of agarose gel were evaluated. Phantom A contained various concentrations of iodine (4.5-1590 HU at 120 kVp). Phantom B consisted of a central component (0, 10, 25, and 40 mgI/cm(3)) and a surrounding component (0, 50, 100, and 200 mgI/cm(3)) with variable iodine concentration. They were scanned by dual-source CT in conventional single-energy mode and dual-energy mode with and without a tin filter. CT values on each gel at the corresponding points were measured and the accuracy of iodine removal was evaluated. On VNE images, the CT number of the gel of Phantom A fell within the range between -15 and +15 HU under 626 and 881 HU at single-energy 120 kVp with and without a tin filter, respectively. With attenuation over these thresholds, iodine concentration of gels was underestimated with the tin filter but overestimated without it. For Phantom B, the mean CT numbers on VNE images in the central gel component surrounded by the gel with iodine concentrations of 0, 50, 100, and 200 mgI/cm(3) were in the range of -19-+6 HU and 21-100 HU with and without the tin filter, respectively. Both with and without a tin filter, iodine removal was accurate under a threshold of iodine concentration. Although a surrounding structure with higher attenuation decreased the accuracy, a tin filter improved the margin of error.

Photochemical conversion of tin-oxo cage compounds studied using hard x-ray photoelectron spectroscopy

NASA Astrophysics Data System (ADS)

Zhang, Yu; Haitjema, Jarich; Liu, Xiaomeng; Johansson, Fredrik; Lindblad, Andreas; Castellanos, Sonia; Ottosson, Niklas; Brouwer, Albert M.

2017-03-01

Several metal-containing molecular inorganic materials are currently considered as photoresists for extreme ultraviolet lithography (EUVL). This is primarily due to their high EUV absorption cross section and small building block size, properties which potentially allow both high sensitivity and resolution as well as low line-edge roughness. The photochemical reaction mechanisms that allow these kinds of materials to function as photoresists, however, are still poorly understood. As a step in this direction, we here discuss photochemical reactions upon deep UV (DUV) irradiation of a model negative-tone EUV photoresist material, namely the well-defined molecular tin-oxo cage compound [(SnR)12O14(OH)6]X2 (R = organic group; X = anion) which is spin coated to thin layers of 20 nm. The core electronic structure (Sn 3d, O 1s and C 1s) of fresh and DUV exposed films were then investigated using synchrotron radiationbased hard X-ray photoelectron spectroscopy (HAXPES). This method provides information about the structure and chemical state of the respective atoms in the material. We performed a comparative HAXPES study of the composition of the tin-oxo cage compound [(SnR)12O14(OH)6](OH)2, either fresh directly after spin-coated vs. DUV-exposed materials under either ambient condition or under a dry N2 atmosphere. Different chemical oxidation states and concentrations of atoms and atom types in the fresh and exposed films were found. We further found that the chemistry resulting from exposure in air and N2 is strikingly different, clearly illustrating the influence of film-gas interactions on the (photo)chemical processes that eventually determine the photoresist. Finally, a mechanistic hypothesis for the basic DUV photoreactions in molecular tin-oxo cages is proposed.

Rapid pH change due to bacteriorhodopsin measured with a tin-oxide electrode.

PubMed Central

Robertson, B; Lukashev, E P

1995-01-01

The photocurrent transient generated by bacteriorhodopsin (bR) on a tin-oxide electrode is due to pH change and not to charge displacement as previously assumed. Films of either randomly oriented or highly oriented purple membranes were deposited on transparent electrodes made of tin-oxide-coated glass. The membranes contained either wild-type or D96N-mutant bR. When excited with yellow light through the glass, the bR pumps protons across the membrane. The result is a rapid local pH change as well as a charge displacement. Experiments with these films show that it is the pH change rather than the displacement that produces the current transient. The calibration for the transient pH measurement is given. The sensitivity of a tin-oxide electrode to a transient pH change is very much larger than its sensitivity to a steady-state pH change. PMID:7787036

Demonstration of high-performance p-type tin oxide thin-film transistors using argon-plasma surface treatments

NASA Astrophysics Data System (ADS)

Bae, Sang-Dae; Kwon, Soo-Hun; Jeong, Hwan-Seok; Kwon, Hyuck-In

2017-07-01

In this work, we investigated the effects of low-temperature argon (Ar)-plasma surface treatments on the physical and chemical structures of p-type tin oxide thin-films and the electrical performance of p-type tin oxide thin-film transistors (TFTs). From the x-ray photoelectron spectroscopy measurement, we found that SnO was the dominant phase in the deposited tin oxide thin-film, and the Ar-plasma treatment partially transformed the tin oxide phase from SnO to SnO2 by oxidation. The resistivity of the tin oxide thin-film increased with the plasma-treatment time because of the reduced hole concentration. In addition, the root-mean-square roughness of the tin oxide thin-film decreased as the plasma-treatment time increased. The p-type oxide TFT with an Ar-plasma-treated tin oxide thin-film exhibited excellent electrical performance with a high current on-off ratio (5.2 × 106) and a low off-current (1.2 × 10-12 A), which demonstrates that the low-temperature Ar-plasma treatment is a simple and effective method for improving the electrical performance of p-type tin oxide TFTs.

Crystal structure of tetra­wickmanite, Mn2+Sn4+(OH)6

PubMed Central

Lafuente, Barbara; Yang, Hexiong; Downs, Robert T.

2015-01-01

The crystal structure of tetra­wickmanite, ideally Mn2+Sn4+(OH)6 [mangan­ese(II) tin(IV) hexa­hydroxide], has been determined based on single-crystal X-ray diffraction data collected from a natural sample from Långban, Sweden. Tetra­wickmanite belongs to the octa­hedral-framework group of hydroxide-perovskite minerals, described by the general formula BB’(OH)6 with a perovskite derivative structure. The structure differs from that of an ABO3 perovskite in that the A site is empty while each O atom is bonded to an H atom. The perovskite B-type cations split into ordered B and B′ sites, which are occupied by Mn2+ and Sn4+, respectively. Tetra­wickmanite exhibits tetra­gonal symmetry and is topologically similar to its cubic polymorph, wickmanite. The tetra­wickmanite structure is characterized by a framework of alternating corner-linked [Mn2+(OH)6] and [Sn4+(OH)6] octa­hedra, both with point-group symmetry -1. Four of the five distinct H atoms in the structure are statistically disordered. The vacant A site is in a cavity in the centre of a distorted cube formed by eight octa­hedra at the corners. However, the hydrogen-atom positions and their hydrogen bonds are not equivalent in every cavity, resulting in two distinct environments. One of the cavities contains a ring of four hydrogen bonds, similar to that found in wickmanite, while the other cavity is more distorted and forms crankshaft-type chains of hydrogen bonds, as previously proposed for tetra­gonal stottite, Fe2+Ge4+(OH)6. PMID:25878828

Autocatalytic Patterning with Silver Using Tin(II) Chloride Sensitizer

ERIC Educational Resources Information Center

Mbindyo, Jeremiah K. N.; Anna, Laura J.; Fell, B. Andrew; Patton, David A.

2011-01-01

A silver mirror can be deposited on many types of surfaces from the reduction of the silver-diammine complex by a reducing sugar as proposed by Kemp in this "Journal". Three extensions of Kemp's demonstration that highlight the role of SnCl[subscript 2] sensitizer in the deposition of a silver mirror on surfaces are presented. The demonstration…

The Fyn tyrosine kinase binds Irs-1 and forms a distinct signaling complex during insulin stimulation.

PubMed

Sun, X J; Pons, S; Asano, T; Myers, M G; Glasheen, E; White, M F

1996-05-03

Irs-proteins link the receptors for insulin/IGF-1, growth hormones, and several interleukins and interferons to signaling proteins that contain Src homology-2 (SH2). To identify new Irs-1-binding proteins, we screened a mouse embryo expression library with recombinant [32P]Irs-1, which revealed a specific association between p59fyn and Irs-1. The SH2 domain in p59fyn bound to phosphorylated Tyr895 and Tyr1172, which are located in YXX(L/I) motifs. Mutation of p59fyn at the COOH-terminal tyrosine phosphorylation site (Tyr531) enhanced its binding to Irs-1 during insulin stimulation. Binding experiments with various SH2 protein revealed that Grb-2 was largely excluded from Irs-1 complexes containing p59fyn, whereas Grb-2 and p85 occurred in the same Irs-1 complex. By comparison with the insulin receptor, p59fyn kinase phosphorylated a unique cohort of tyrosine residues in Irs-1. These results outline a role for p59fyn or other related Src-kinases during insulin and cytokine signaling.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allendorf, M.D.; Arsenlis, A.; Bastasz, R.

Titanium nitride (TiN) films deposited by chemical vapor deposition (CVD) techniques are of interest for a wide range of commercial applications. In this report, the authors describe a mechanism that predicts Tin film growth rates from TiCl{sub 4}/NH{sub 3} mixtures as a function of process parameters, including inlet reactant concentrations, substrate temperatures, reactor pressures, and total gas flow rates. Model predictions were verified by comparison with the results of TiN deposition experiments in the literature and with measurements made in a new stagnation-flow reactor developed for the purpose of testing deposition mechanisms such as this. In addition, they describe abmore » initio calculations that predict thermodynamic properties for titanium-containing compounds. The results of calculations using Moeller-Plesset perturbation theory, density functional theory, and coupled cluster theory are encouraging and suggest that these methods can be used to estimate thermodynamic data that are essential for the development of CVD models involving transition-metal compounds. Finally, measurements of the adsorption and desorption kinetics of NH{sub 3} on TiN films using temperature-programmed desorption are described and their relevance to TiN CVD and mechanism development are discussed.« less

Free electron lasers for 13nm EUV lithography: RF design strategies to minimise investment and operational costs

NASA Astrophysics Data System (ADS)

Keens, Simon; Rossa, Bernhard; Frei, Marcel

2016-03-01

As the semiconductor industry proceeds to develop ever better sources of extreme ultraviolet (EUV) light for photolithography applications, two distinct technologies have come to prominence: Tin-plasma and free electron laser (FEL) sources. Tin plasma sources have been in development within the industry for many years, and have been widely reported. Meanwhile, FELs represent the most promising alternative to create high power EUV frequencies and, while tin-plasma source development has been ongoing, such lasers have been continuously developed by academic institutions for use in fundamental research programmes in conjunction with universities and national scientific institutions. This paper follows developments in the field of academic FELs, and presents information regarding novel technologies, specifically in the area of RF design strategy, that may be incorporated into future industrial FEL systems for EUV lithography in order to minimize the necessary investment and operational costs. It goes on to try to assess the cost-benefit of an alternate RF design strategy, based upon previous studies.

50 CFR 23.71 - How can I trade internationally in sturgeon caviar?

Code of Federal Regulations, 2014 CFR

2014-10-01

...-export sturgeon caviar only if labels are affixed to containers prior to export or re-export in... container. In the United States, the design of the label will be determined by the labeler in accordance with the requirements of this section. (ii) Primary container means any container (tin, jar, pail or...

GEMAS - Tin and Tungsten: possible sources of enriched concentrations in soils in European countries

NASA Astrophysics Data System (ADS)

João Batista, Maria; Filipe, Augusto; Reimann, Clemens

2014-05-01

Tin and tungsten occur related with magmatic differentiation and can be installed in fissures and veins of magmatic rocks or in the neighbor metasediments. Generally, both elements have low chemical mobility in the superficial environment although effectively mobile in detrital media such as stream sediments and deposited in alluvial soils. The most important tin-tungsten deposits in Europe are in Variscides. From the northern Europe, 985 samples and from southern Europe 1123 samples were collected both in agricultural and grazing lands. Analysis were made of Sn , W, pH, TOC, SiO2 from the upper 20 and 10 cm of agricultural and grazing soils, respectively. The present study is part of the GEMAS project a joint project of European geochemical mapping between the EuroGeoSurvey Geochemical Expert Group and EuroMetaux. The results show that in general, at the European (continental) scale natural processes are dominant. It is clear the distinction between NE Europe and SW European tin and tungsten concentrations in soils. Tin geometric mean concentrations in the northern Europe is 0.57 mg kg-1 in agricultural soils and 0.62 mg kg-1 in grazing land; southern Europe 0.91 mg kg-1 in agricultural soils and 0.95 mg kg-1 in grazing land. Tungsten geometric mean concentrations in northern Europe is 0.067 mg kg-1 in agricultural soils and 0.073 mg kg-1 in grazing land and in southern Europe is 0.085 mg kg-1 in agricultural soils and 0.090 mg kg-1 in grazing land. Limit between north and south is the maximum extent of the last glaciation. Grazing land, undisturbed soils for a period of several years, have higher concentrations of Sn and W than agricultural soils which raises the question that if only natural processes are observed. Parent material seems to be the main source of Sn and W to soil. Sn-W rich Variscan granitic intrusions of Central Iberian Zone, Massif Central, Brittany, Cornwall and Bohemia are reflected in soil concentrations. TOC is higher in northern than in southern soils and SiO2 is higher in loess sediments region, in the North German-Poland basin and in the Paris basin. Organic matter may immobilise these metals and silica content influences metallic elements concentrations in soils. Natural processes of soil development, land management of agricultural soils and population density all together may be responsible for higher concentrations of W in the soils of Netherlands Germany, Belgium, Switzerland and northeast France which seems not related with Sn-W mineral provinces. Tin and tungsten are enriched in the Precambrian shields compared to the Caledonian shields soils in the northern countries, although in northern countries climatic conditions may play the most important role in these elements concentrations. Tin and tungsten and tin or tungsten alone or in association of precious metals, copper, uranium, niobium, beryllium, titanium altogether were extracted in 650 small or median size mines in Portugal. Except tin in Neves Corvo mine of the Iberian Pyrite Belt the rest of these mines occurred in the Variscides granitic intrusions region. Tin and tungsten concentrations are therefore well reflected in the northern Portugal soils. At the GEMAS density of sampling pollution and local natural phenomena are not reflected in mapping but this important province is well delimited.

Studies of Lubricating Materials in Vacuum

NASA Technical Reports Server (NTRS)

Buckley, D. H.; Johnson, R. L.; Swikert, M. A.

1964-01-01

Lubricating materials for use in a vacuum environment have been the subject of a series of experimental investigations. Evaporation properties were evaluated for solid polymeric compositions. Friction and wear studies explored the behavior during sliding contact for series of polymeric compositions, binary alloys containing soft film-forming phases, complex alloys with film-forming materials, and a burnished MoS2 film. Friction and wear experiments were conducted at 10(exp-9)mm Hg with a 3/16-inch-radius-hemisphere rider specimen sliding on the flat surface of a rotating 2-1/2-inch-diameter disk specimen with materials that had low rates of evaporation. The influence of fillers in polytetrafluoroethylene (PTFE) on decomposition during vacuum friction studies was determined with a mass spectrometer. A real advantage in reducing decomposition and improving friction wear properties is gained by adding fillers (e.g., copper) that improve thermal conductivity through the composite materials. A polyimide and an epoxy-MoS2 composition material were found to have better friction and wear properties than PTFE compositions. A series of alloys (cast binary as well as more complex alloys) that contained microinclusions of potential film-forming material was studied. These materials replaced the normal surface oxides as they were worn away on sliding contact. Iron sulfide, nickel oxide, and tin are typical film-forming materials employed and were demonstrated to be effective in inhibiting surface welding and reducing friction. A burnished MoS2 film applied to type 440-C stainless steel in argon with a rotating soft wire brush had good endurance properties but somewhat higher friction than commercially available bonded films. An oil film applied to the burnished MoS2 markedly reduced its endurance life.

Reactivity of lithium n-butyl amidinates towards group 14 metal(II) chlorides providing series of hetero- and homoleptic tetrylenes.

PubMed

Chlupatý, Tomáš; Padělková, Zdeňka; Lyčka, Antonín; Brus, Jiří; Růžička, Aleš

2012-04-28

The new class of homo- and heteroleptic n-butyl-N,N'-disubstituted amidinato group 14 metal(II) complexes were prepared by salt elimination from starting lithium amidinates and metal(II) chlorides both in stoichiometric ratio 2:1 and 1:1, respectively. The target amidinates contain less bulky isopropyl or cyclohexyl as well as a sterically demanding aromatic substituent. Desired 1:1 Pb(II) complexes are not accessible by the described procedure. Ligand transfer from Pb to Sn is taking place if homoleptic Pb(II) compounds are reacted with SnCl(2). Prepared tetrylenes were characterized by (1)H, (13)C, (119)Sn and (207)Pb NMR spectroscopy in C(6)D(6) or THF-d(8). X-Ray diffraction studies of one heteroleptic Ge(II) monomeric where the coordination polyhedron of the three coordinated germanium atoms is a trigonal pyramid, two different dimeric structures of heteroleptic Sn(II) complexes, one amidine hydroiodide byproduct and the oxidation product of the heteroleptic chloro Sn(II) amidinate as a tetranuclear species with two Sn(IV) and two Sn(II) atoms in central Sn(2)O(2) planar ring were performed on appropriate single crystals. The dimer of one of the heteroleptic stannylenes reveals a new type of monomeric units connection, weak Sn-Cl contact and an interaction of the tin atom with delocalized N-C(C)-N system of the amidinato ligand of the second molecule. This journal is © The Royal Society of Chemistry 2012

Structural, compositional, optical and colorimetric characterization of TiN-nanoparticles

NASA Astrophysics Data System (ADS)

Reinholdt, A.; Pecenka, R.; Pinchuk, A.; Runte, S.; Stepanov, A. L.; Weirich, Th. E.; Kreibig, U.

2004-10-01

We present results of an investigation of TiN nanoparticles, which were produced by laser ablation/evaporation and adiabatic expansion with the nanoparticle beam apparatus LUCAS. Compositional and structural characterization, using secondary ion mass spectrometry (SIMS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD) and selected area electron diffraction (SAED), revealed that crystalline and almost stoichiometric particles were formed and that they are susceptible to oxidation. Furthermore, transmission electron microscopy (TEM) analysis showed that TiN nanoparticles exhibit cuboid shapes. The size distributions were obtained using the edge length as parameter. They are fairly broad and the mean particle diameter depends on the seeding gas flow (the pressure) that is applied to the ablation chamber during production. In situ optical transmission spectra of the TiN nanoparticles deposited on a quartz substrate indicate a pronounced single Mie resonance at around 1.7 eV and an absorption flank starting at approximately 3.0 eV. The experimental optical extinction spectra of different samples were fitted using Mie theory calculations. The dielectric function of bulk TiN was modified to account for size and interface damping of the Mie resonance. Due to the distinct absorption band, TiN may be used as a color pigment. The dependence of the color stimulus on the extinction cross-section as well as on the product of the particle concentration and the sample thickness were examined. Chromaticity coordinates were derived according to the CIE 1976 (L^*a^*b^*) color space from the in situ optical transmission spectra.

Group 4 Metalloporphyrin diolato Complexes and Catalytic Application of Metalloporphyrins and Related Transition Metal Complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Du, Guodong

In this work, the first examples of group 4 metalloporphyrin 1,2-diolato complexes were synthesized through a number of strategies. In general, treatment of imido metalloporphyrin complexes, (TTP)M=NR, (M = Ti, Zr, Hf), with vicinal diols led to the formation of a series of diolato complexes. Alternatively, the chelating pinacolate complexes could be prepared by metathesis of (TTP)MCl 2 (M = Ti, Hf) with disodium pinacolate. These complexes were found to undergo C-C cleavage reactions to produce organic carbonyl compounds. For titanium porphyrins, treatment of a titanium(II) alkyne adduct, (TTP)Ti(η 2-PhC≡CPh), with aromatic aldehydes or aryl ketones resulted in reductive couplingmore » of the carbonyl groups to produce the corresponding diolato complexes. Aliphatic aldehydes or ketones were not reactive towards (TTP)Ti(η 2-PhC≡CPh). However, these carbonyl compounds could be incorporated into a diolato complex on reaction with a reactive precursor, (TTP)Ti[O(Ph) 2C(Ph) 2O] to provide unsymmetrical diolato complexes via cross coupling reactions. In addition, an enediolato complex (TTP)Ti(OCPhCPhO) was obtained from the reaction of (TTP)Ti(η 2-PhC≡CPh) with benzoin. Titanium porphyrin diolato complexes were found to be intermediates in the (TTP)Ti=O-catalyzed cleavage reactions of vicinal diols, in which atmospheric oxygen was the oxidant. Furthermore, (TTP)Ti=O was capable of catalyzing the oxidation of benzyl alcohol and α-hydroxy ketones to benzaldehyde and α-diketones, respectively. Other high valent metalloporphyrin complexes also can catalyze the oxidative diol cleavage and the benzyl alcohol oxidation reactions with dioxygen. A comparison of Ti(IV) and Sn(IV) porphyrin chemistry was undertaken. While chelated diolato complexes were invariably obtained for titanium porphyrins on treatment with 1,2-diols, the reaction of vicinal diols with tin porphyrins gave a number of products, including mono-, bis-alkoxo, and chelating diolato complexes, depending on the identity of diols and the stoichiometry employed. It was also found that tin porphyrin complexes promoted the oxidative cleavage of vicinal diols and the oxidation of α-ketols to α-diketones with dioxygen. In extending the chemistry of metalloporphyrins and analogous complexes, a series of chiral tetraaza macrocyclic ligands and metal complexes were designed and synthesized. Examination of iron(II) complexes showed that they were efficient catalysts for the cyclopropanation of styrene by diazo reagents. Good yields and high diastereoselectivity were obtained with modest enantioselectivity. A rationalization of the stereoselectivity was presented on the basis of structural factors in a carbene intermediate.« less

Copper status in weanling rats fed low levels of inorganic tin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rader, J.I.; Hight, S.C.

1991-03-15

The metabolism of Cu and Fe is adversely affected by ingestion of tin (Sn). In the present study, weanling male rats were fed 33 ug Sn/g in purified Cu-adequate or Cu-deficient diets for 14 or 28 days. Diets were based upon diet AIN-76A and contained 55% glucose and 15% starch. Ceruloplasmin was undetectable in serum of rats fed diets 2, 3 and 4 for 14 or 28 days. Superoxide dismutase (SOD) and Cu in liver decreased when 33 ug Sn/g was included in +Cu diets. Wt. gain, relative heart wt., SOD, and Cu and Fe in liver were sensitive indicesmore » of copper depletion in rats fed {minus}Cu diets. Cu status in rats fed {minus}Cu diets for 14 or 28 days was adversely affected by inclusion of Sn as indicated by changes in hemoglobin (HGB) and relative heart wt. Ingestion of low levels of inorganic tin causes Cu depletion in rats fed +Cu diets and accelerated the appearance of signs of copper deficiency in those fed {minus}Cu diets.« less

Reaction of tin(iv) phthalocyanine dichloride with decamethylmetallocenes (M = CrII and CoII). Strong magnetic coupling of spins in (Cp*2Co+){SnIVCl2(Pc˙3-)}˙-·2C6H4Cl2.

PubMed

Konarev, Dmitri V; Troyanov, Sergey I; Shestakov, Alexander F; Yudanova, Evgeniya I; Otsuka, Akihiro; Yamochi, Hideki; Kitagawa, Hiroshi; Lyubovskaya, Rimma N

2018-01-23

The reaction of tin(iv) phthalocyanine dichloride {Sn IV Cl 2 (Pc 2- )} with decamethylmetallocenes (Cp* 2 M, M = Co, Cr) has been studied. Decamethylcobaltocene reduces Sn IV Cl 2 (Pc 2- ) to form the (Cp* 2 Co + ){Sn IV Cl 2 (Pc˙ 3- )}˙ - ·2C 6 H 4 Cl 2 (1) complex. The negative charge of {Sn IV Cl 2 (Pc˙ 3- )}˙ - is delocalized over the Pc macrocycle providing the alternation of the C-N(imine) bonds, the appearance of new bands in the NIR range and a strong blue shift of both the Soret and Q-bands in the spectrum of 1. The magnetic moment of 1 is equal to 1.68μ B at 300 K, indicating the contribution of one S = 1/2 spin of the Pc˙ 3- macrocycles. These macrocycles form closely packed double stacks in 1 with effective π-π interactions providing strong antiferromagnetic coupling of spins at a Weiss temperature of -80 K. Decamethylchromocene initially also reduces Sn IV Cl 2 (Pc 2- ) to form the [(Cp* 2 Cr + ){Sn VI Cl 2 (Pc˙ 3- )}˙ - complex but further reaction between the ions is observed. This reaction is accompanied by the substitution of one Cp* ligand of Cp* 2 Cr by chloride anions originating from {Sn IV Cl 2 (Pc˙ 3- )}˙ - to form the complex {(Cp*CrCl 2 )(Sn IV (μ-Cl)(Pc 2- ))}·C 6 H 4 Cl 2 (2) in which the (Cp*CrCl 2 ) and {Sn IV (Pc 2- )} species are bonded through the μ-bridged Cl - anion. According to the DFT calculations, this reaction proceeds via an intermediate [(Cp* 2 CrCl)(SnClPc)] complex.

Distinct mutations in yeast TAF(II)25 differentially affect the composition of TFIID and SAGA complexes as well as global gene expression patterns.

PubMed

Kirschner, Doris B; vom Baur, Elmar; Thibault, Christelle; Sanders, Steven L; Gangloff, Yann-Gaël; Davidson, Irwin; Weil, P Anthony; Tora, Làszlò

2002-05-01

The RNA polymerase II transcription factor TFIID, composed of the TATA-binding protein (TBP) and TBP-associated factors (TAF(II)s), nucleates preinitiation complex formation at protein-coding gene promoters. SAGA, a second TAF(II)-containing multiprotein complex, is involved in transcription regulation in Saccharomyces cerevisiae. One of the essential protein components common to SAGA and TFIID is yTAF(II)25. We define a minimal evolutionarily conserved 91-amino-acid region of TAF(II)25 containing a histone fold domain that is necessary and sufficient for growth in vivo. Different temperature-sensitive mutations of yTAF(II)25 or chimeras with the human homologue TAF(II)30 arrested cell growth at either the G(1) or G(2)/M cell cycle phase and displayed distinct phenotypic changes and gene expression patterns. Immunoprecipitation studies revealed that TAF(II)25 mutation-dependent gene expression and phenotypic changes correlated at least partially with the integrity of SAGA and TFIID. Genome-wide expression analysis revealed that the five TAF(II)25 temperature-sensitive mutant alleles individually affect the expression of between 18 and 33% of genes, whereas taken together they affect 64% of all class II genes. Thus, different yTAF(II)25 mutations induce distinct phenotypes and affect the regulation of different subsets of genes, demonstrating that no individual TAF(II) mutant allele reflects the full range of its normal functions.

Structural transformations, water incorporation and transport properties of tin-substituted barium indate

NASA Astrophysics Data System (ADS)

Cichy, Kacper; Skubida, Wojciech; Świerczek, Konrad

2018-06-01

Incorporation of water into tin-substituted BaIn1-xSnxO3-δ (x = 0.1-0.3) is shown to influence crystal structure at room temperature, structural transformations at high temperatures and ionic transport properties of the materials. Increasing tin content stabilizes oxygen vacancy-disordered perovskite-type phase, which together with large changes of the unit cell volume occurring during hydration and dehydration processes, result in a complex structural behavior, as documented by high-temperature X-ray diffraction and thermogravimetric studies. Impedance spectroscopy measurements at elevated temperatures (350-800 °C) revealed very high proton conductivity in BaIn.8Sn.2O3-δ, exceeding 1.1·10-3 S cm-1 at 500 °C, with high values of the transference number in wet air. At the same time, relaxation kinetics of the electrical conductivity showed a monotonous nature, which indicates negligible component of the electronic hole conductivity in the hydrated material. The oxides are extremely moisture-sensitive, which results in a significant mechanical stability problems, affecting possibility to prepare electrolyte membranes.

The development of a hydrologic-hydraulic representation of an urbanscape: the case study of Nashville, Tennessee

NASA Astrophysics Data System (ADS)

Sedlar, F.; Ivanov, V. Y.; Shao, J.; Narayan, U.; Nardi, F.; Adams, T. E.; Merwade, V.; Wright, D. B.; Kim, J.; Fatichi, S.; Rakhmatulina, E.

2013-12-01

Incorporating elevation data into coupled hydraulic and hydrologic models with the use of triangulated irregular networks (TINs) provides a detailed and highly customizable representation of the original domain. Until recently the resolution of such digital elevation models was 1 or 1/3 arc second (10-30 meters). Aided by the use of LiDAR, digital elevation models are now available at the 1/9 arc second resolution (1-3 meters). With elevation data at this level of resolution watershed details that are overlooked at a 10-30 meter resolution can now be resolved and incorporated into the TIN. For urban flood modeling this implies that street level features can be resolved. However to provide a useful picture of the flooding as a whole, this data would need to be integrated across a citywide scale. To prove the feasibility, process, and capabilities of generating such a detailed and large scale TIN, we present a case study of Nashville, TN, USA, during the May 1-2, 2010 flooding, a 1,000 year storm event. With the use of ArcGIS, HEC-RAS, Triangle, and additionally developed processing methodologies, an approach is developed to generate a hydrologically relevant and detailed TIN of the entire urbanscape of Nashville. This TIN incorporates three separate aspects; the watershed, the floodplain, and the city. The watershed component contains the elevation data for the delineated watershed, roughly 1,000 km2 at 1-3 meter resolution. The floodplain encompasses over 300 channel cross sections of the Cumberland River and a delineated floodplain. The city element comprises over 500,000 buildings and all major roadways within the watershed. Once generated, the resulting triangulation of the TIN is optimized with the Triangle software for input to the coupled hydraulic and hydrological model, tRIBS-OFM. Hydrologically relevant areas such as the floodplain are densified and constraints are set on the minimum triangle area for the entire TIN. Upon running the coupled hydraulic and hydrological model with the appropriate forcings, the spatial dynamics of the flooding will then be resolved at a street level across the entire city. The analysis capabilities afforded at this resolution and across such a large area will facilitate urban flood predictions coupled with hydrologic forecasts as well as a better understanding of the spatial dynamics of urban flooding.

Tribological characterization of TiN coatings prepared by magnetron sputtering

NASA Astrophysics Data System (ADS)

Makwana, Nishant S.; Chauhan, Kamlesh V.; Sonera, Akshay L.; Chauhan, Dharmesh B.; Dave, Divyeshkumar P.; Rawal, Sushant K.

2018-05-01

Titanium nitride (TiN) coating deposited on aluminium and brass pin substrates using RF reactive magnetron sputtering. The structural properties and surface morphology were characterized by X-ray diffraction (XRD), atomic force microscope (AFM) and field emission scanning electron microscope (FE-SEM). There was formation of (101) Ti2N, (110) TiN2 and (102) TiN0.30 peaks at 3.5Pa, 2Pa and 1.25Pa sputtering pressure respectively. The tribological properties of coating were inspected using pin on disc tribometer equipment. It was observed that TiN coated aluminium and brass pins demonstrated improved wear resistance than uncoated aluminium and brass pins.

Reductive spectrophotometry of divalent tin sensitization on soda lime glass

NASA Astrophysics Data System (ADS)

Bejugam, Vinith; Wei, Xingfei; Roper, D. Keith

2016-07-01

Rapid and facile evaluation of tin (II) sensitization could lead to improved understanding of metal deposition in electroless (EL) plating. This report used a balanced redox reaction between 3,3‧,5,5‧-tetramethylbenzidine dihydrochloride (TMB-HCL) and N-bromosuccinimide (NBS) to evaluate effects of sensitization conditions (i.e., sensitization time, analyte concentration, aqueous immersion, and acid content) on the accumulated mass of surface-associated divalent tin ion. The accumulated mass of tin (II) increased as the sensitization time increased up to 30 s in proportion to aqueous tin (II) chloride concentrations between 2.6 and 26 mM at a trifluoroacetic acid (TFA) content of 68 mM. The average mass peaked at 7.3 nanomoles (nmol) per cm2 after a 5 s aqueous immersion post-sensitization, and then decreased with increasing aqueous immersion post-sensitization. The total average tin (II) + tin (IV) accumulated on soda lime glass measured by inductively coupled plasma optical emission spectrometry (ICP-OES) was 17% higher at 30 s sensitization, suggesting a fraction of the tin (II) present may have oxidized to tin (IV). These results indicated that in situ spectrophotometric evaluation of tin (II) could support development of EL plating for electronics, catalysis, and solar cells.

Structural studies of supported tin catalysts

NASA Astrophysics Data System (ADS)

Nava, Noel; Viveros, Tomás

1999-11-01

Tin oxide was supported on aluminium oxide, titanium oxide, magnesium oxide and silicon oxide, and the resulting interactions between the components in the prepared samples and after reduction were characterized by Mössbauer spectroscopy. It was observed that in the oxide state, tin is present as SnO2 on alumina, magnesia and silica, but on titania tin occupies Ti sites in the structure. After hydrogen treatment at high temperatures, tin is reduced from Sn(4) to Sn(2) on alumina and titania; it is reduced from Sn(4) to Sn(0) on silica, and is practically not reduced on magnesia. These results reveal the degree of interaction between tin and the different supports studied.

76 FR 75794 - Significant New Use Rules on Certain Chemical Substances; Withdrawal of Two Chemical Substances

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-05

...) for chemical substances which were the subject of premanufacture notices (PMNs), i.e., rutile, tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped (PMN P-06-37... rutile, tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623-01-2) and rutile, tin zinc, sodium-doped...

Effect of Nitrogen Content on Physical and Chemical Properties of TiN Thin Films Prepared by DC Magnetron Sputtering with Supported Discharge

NASA Astrophysics Data System (ADS)

Kavitha, A.; Kannan, R.; Gunasekhar, K. R.; Rajashabala, S.

2017-10-01

Amorphous titanium nitride (TiN) thin films have been prepared on silicon (Si) and glass substrates by direct-current (DC) reactive magnetron sputtering with a supported discharge (triode). Nitrogen gas (N2) at partial pressure of 0.3 Pa, 0.4 Pa, 0.5 Pa, and 0.6 Pa was used to prepare the TiN thin films, maintaining total pressure of argon and N2 of about 0.7 Pa. The chemical, microstructural, optical, and electrical properties of the TiN thin films were systematically studied. Presence of different phases of Ti with nitrogen (N), oxygen (O2), and carbon (C) elements was revealed by x-ray photoelectron spectroscopy characterization. Increase in the nitrogen pressure from 0.3 Pa to 0.6 Pa reduced the optical bandgap of the TiN thin film from 2.9 eV to 2.7 eV. Photoluminescence study showed that TiN thin film deposited at N2 partial pressure of 0.3 Pa exhibited three shoulder peaks at 330 nm, 335 nm, and 340 nm, which disappeared when the sample was deposited with N2 partial pressure of 0.6 Pa. Increase in the nitrogen content decreased the electrical resistivity of the TiN thin film from 3200 μΩ cm to 1800 μΩ cm. Atomic force microscopy studies of the TiN thin films deposited with N2 partial pressure of 0.6 Pa showed a uniform surface pattern associated with accumulation of fine grains. The results and advantages of this method of preparing TiN thin films are also reported.

Trinuclear organooxotin assemblies from solvothermal synthesis reaction: Crystal structure, hydrogen bonding and π π stacking interaction

NASA Astrophysics Data System (ADS)

Ma, Chunlin; Sun, Junshan; Zhang, Rufen

2007-05-01

Two new trinuclear mono-organooxotin(IV) complexes with 2,3,4,5-tetrafluorobenzoic acid and sodium perchlorate of the types: [(SnR) 3(OH)(2,3,4,5-F 4C 6HCO 2) 4 · ClO 4] · [O 2CC 6HF 4](R = PhCH 2, 1; o- F-PhCH 2 for 2), have been solvothermally synthesized and structurally characterized by elemental, IR, 1H, 13C and 119Sn NMR and X-ray crystallography diffraction analyses. Complex 2 is also characterized by X-ray crystallography diffraction analyses. In complex 2, four carboxyl groups and a perchlorate bridged three tin atoms in a cyclohexane chair arrangement and form the basic framework. A hydroxyl group comprises the oxygen components of the stannoxane ring system. In these complexes, weak but significant intramolecular hydrogen bonding and π-π stacking interaction are also shown. These contacts lead to aggregation and supramolecular assembly of complexes 1 and 2 into 1D or 2D framework.

Crystal structure of tin(IV) chloride octa­hydrate

PubMed Central

Hennings, Erik; Schmidt, Horst; Voigt, Wolfgang

2014-01-01

The title compound, [SnCl4(H2O)2]·6H2O, was crystallized according to the solid–liquid phase diagram at lower temperatures. It is built-up of SnCl4(H2O)2 octa­hedral units (point group symmetry 2) and lattice water mol­ecules. An intricate three-dimensional network of O—H⋯O and O—H⋯Cl hydrogen bonds between the complex molecules and the lattice water molecules is formed in the crystal structure. PMID:25552971

Synthesis, structure and property of diorganotin complexes with chiral N-(5-chlorosalicylidene)valinate ligand

NASA Astrophysics Data System (ADS)

Tian, Laijin; Yao, Yanze; Wang, Yuhua; Liu, Jin

2018-03-01

Six new diorganotin N-[(5-chloro-2-oxyphenyl)methylene]valinates, R2SnL (R = Me, 1; Et, 2; L = 5-Cl-2-OC6H3CH = NCH(i-Pr)COO: (S)-, a; (R)-, b; (RS)-, c), have been synthesized from the reaction of R2SnCl2 with the chiral ligand KHL (potassium salt of HL) in different solvents and characterized by elemental analysis, IR, NMR (1H, 13C and 119Sn) spectra. In benzene, the configuration of the chiral ligand was retained. (S)-Enantiomers (1a and 2a) and (R)-enantiomers (1b and 2b) display discrete molecular structures with distorted trigonal bipyramidal geometries in which two C atoms of organic groups (R) and the imino N atom occupy the equatorial positions and a phenoxide O and an unidentate carboxylate group O atom are in the axial orientation. In the methanol, the chiral ligand was racemized. 1cṡMeOH is a centrosymmetric dimers formed by (R)- and (S)- enantiomers through two Snsbnd OṡṡṡSn bridges. The coordination geometry of the Sn atom can be described as a distorted pentagonal bipyramid with two methyl groups in axial positions. The crystal of 2c is composed of two threefold symmetric trimers, a [Et2SnL-(R)]3 and a [Et2SnL-(S)]3, with a macrocyclic 12-membered ring structure formed by the bidenate bridging coordination of carboxylate group to tin atoms. Each tin atom is six-coordinated in distorted [SnC2NO3] octahedron geometry. The fluorescence properties of ligand KHL and complexes 1 (1a-1c) and 2 (2a-2c) have been measured. The results show the complexes may be explored for potential luminescent materials.

Fabrication of TiN nanorods by electrospinning and their electrochemical properties

NASA Astrophysics Data System (ADS)

Sun, Dongfei; Lang, Junwei; Yan, Xingbin; Hu, Litian; Xue, Qunji

2011-05-01

TiN nanorods were synthesized using electrospinning technique followed by thermolysis in different atmospheres. A dimethyl formamide-ethanol solution of poly-(vinyl pyrrolidone) and Ti (IV)-isopropoxide was used as the electrospinning precursor solution and as-spun nanofibers were calcined at 500 °C in air to generate TiO 2 nanofibers. Subsequently, a conversion from TiO 2 nanofibers to TiN nanorods was employed by the nitridation treatment at 600˜1400 °C in ammonia atmosphere. A typical characteristic of the final products was that the pristine nanofibers were cut into nanorods. The conversion from TiO 2 to TiN was realized when the nitridation temperature was above 800 °C. As-prepared nanorods were composed of TiN nano-crystallites and the average crystallite size gradually increased with the increase of the nitridation temperature. Electrochemical properties of TiN nanorods showed strong dependence on the nitridation temperature. The maximum value of the specific capacitance was obtained from the TiN nanorods prepared at 800 °C.

Methicillin-Susceptible Staphylococcus aureus Endocarditis Isolates Are Associated With Clonal Complex 30 Genotype and a Distinct Repertoire of Enterotoxins and Adhesins

PubMed Central

Nienaber, Juhsien J.C.; Sharma Kuinkel, Batu K.; Clarke-Pearson, Michael; Lamlertthon, Supaporn; Park, Lawrence; Rude, Thomas H.; Barriere, Steve; Woods, Christopher W.; Chu, Vivian H.; Marín, Mercedes; Bukovski, Suzana; Garcia, Patricia; Corey, G.Ralph; Korman, Tony; Doco-Lecompte, Thanh; Murdoch, David R.; Reller, L. Barth

2011-01-01

Background. Using multinational collections of methicillin-susceptible Staphylococcus aureus (MSSA) isolates from infective endocarditis (IE) and soft tissue infections (STIs), we sought to (1) validate the finding that S. aureus in clonal complex (CC) 30 is associated with hematogenous complications and (2) test the hypothesis that specific genetic characteristics in S. aureus are associated with infection severity. Methods. IE and STI isolates from 2 cohorts were frequency matched by geographic origin. Isolates underwent spa typing to infer CC and multiplex polymerase chain reaction for presence of virulence genes. Results. 114 isolate pairs were genotyped. IE isolates were more likely to be CC30 (19.5% vs 6.2%; P = .005) and to contain 3 adhesins (clfB, cna, map/eap; P < .0001 for all) and 5 enterotoxins (tst, sea, sed, see, and sei; P ≤ .005 for all). CC30 isolates were more likely to contain cna, tst, sea, see, seg, and chp (P < .05 for all). Conclusions. MSSA IE isolates were significantly more likely to be CC30 and to possess a distinct repertoire of virulence genes than MSSA STI isolates from the same region. The genetic basis of this association requires further study. PMID:21844296

Conjugated Polymers Via Direct Arylation Polymerization in Continuous Flow: Minimizing the Cost and Batch-to-Batch Variations for High-Throughput Energy Conversion.

PubMed

Gobalasingham, Nemal S; Carlé, Jon E; Krebs, Frederik C; Thompson, Barry C; Bundgaard, Eva; Helgesen, Martin

2017-11-01

Continuous flow methods are utilized in conjunction with direct arylation polymerization (DArP) for the scaled synthesis of the roll-to-roll compatible polymer, poly[(2,5-bis(2-hexyldecyloxy)phenylene)-alt-(4,7-di(thiophen-2-yl)-benzo[c][1,2,5]thiadiazole)] (PPDTBT). PPDTBT is based on simple, inexpensive, and scalable monomers using thienyl-flanked benzothiadiazole as the acceptor, which is the first β-unprotected substrate to be used in continuous flow via DArP, enabling critical evaluation of the suitability of this emerging synthetic method for minimizing defects and for the scaled synthesis of high-performance materials. To demonstrate the usefulness of the method, DArP-prepared PPDTBT via continuous flow synthesis is employed for the preparation of indium tin oxide (ITO)-free and flexible roll-coated solar cells to achieve a power conversion efficiency of 3.5% for 1 cm 2 devices, which is comparable to the performance of PPDTBT polymerized through Stille cross coupling. These efforts demonstrate the distinct advantages of the continuous flow protocol with DArP avoiding use of toxic tin chemicals, reducing the associated costs of polymer upscaling, and minimizing batch-to-batch variations for high-quality material. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthetic Vision Technology Demonstration. Volume 3. Flight Tests

DTIC Science & Technology

1993-12-01

diameter increments for the FSSP and secondary PMS probes ( PMS2 ). For each approach recorded for the sortie, general information recorded in the file... PMS2 ). This final file was given a suffix of "PM2". Each of these files contained multiple dataSit separated by commas rather than spaces. Since the...s I P1.r: 0666011 APPU0O: a TIN PMUCO(SA): 163453-164661 HTEG. PROFLE OF PMS2 RAIN RATE MTEG. PROFLE OF PROBES LWC 819092, Approach #7 MGMjs2

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

40 CFR 421.296 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin Subcategory... wastewater pollutants in secondary tin process wastewater introduced into a POTW shall not exceed the following values: (a) Tin smelter SO2 scrubber. PSNS for the Secondary Tin Subcategory Pollutant or...

Design of an experiment for the production of a foamed tin sample

NASA Technical Reports Server (NTRS)

Wernimont, E.

1986-01-01

One of the major experiments in the GAS container is concerned with the experimental production of a foamed metal. A foamed metal is one that contains a significant amount of gas bubbles suspended in its solid volume. Purdue's GAS team proposes to do this with the help of a solid zinc carbonate that gives off carbon dioxide at high temperatures. Because of low energy requirements, the metal used for this experiment is tin. It is hoped that the use of near zero environment will keep the suspended bubbles more uniform than in an Earth based process, hence not depleting the physical strength of the material as greatly as is observed on Earth.

Low resistivity contact to iron-pnictide superconductors

DOEpatents

Tanatar, Makariy; Prozorov, Ruslan; Ni, Ni; Bud& #x27; ko, Sergey; Canfield, Paul

2013-05-28

Method of making a low resistivity electrical connection between an electrical conductor and an iron pnictide superconductor involves connecting the electrical conductor and superconductor using a tin or tin-based material therebetween, such as using a tin or tin-based solder. The superconductor can be based on doped AFe.sub.2As.sub.2, where A can be Ca, Sr, Ba, Eu or combinations thereof for purposes of illustration only.

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

40 CFR 421.295 - Pretreatment standards for existing sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... existing sources. The mass of wastewater pollutants in secondary tin process wastewater introduced into a POTW must not exceed the following values: (a) Tin smelter SO2 scrubber. PSES for the Secondary Tin...

Heterobimetallic thiocyanato-bridged coordination polymers based on [Hg(SCN) 4] 2-: Synthesis, crystal structure, magnetic properties and ESR studies

NASA Astrophysics Data System (ADS)

Jian, Fang-Fang; Xiao, Hai-Lian; Liu, Fa Qian

2006-12-01

Three new M/Hg bimetallic thiocyanato-bridged coordination polymers; [Hg(SCN) 4Ni(Im) 3] ∞1, [Hg(SCN) 4Mn(Im) 2] ∞2, and [Hg(SCN) 4Cu(Me-Im) 2 Hg(SCN) 4Cu(Me-Im) 4] ∞3, (Im=imidazole, Me-Im= N-methyl-imidazole), have been synthesized and characterized by means of elemental analysis, ESR, and single-crystal X-ray. X-ray diffraction analysis reveals that these three complexes all form 3D network structure, and their structures all contain a thiocyanato-bridged Hg⋯M⋯Hg chain ( M=Mn, Ni, Cu) in which the metal and mercury centers exhibit different coordination environments. In complex 1, the [Hg(SCN) 4] 2- anion connects three [Ni(Im) 3] 2+ using three SCN ligands giving rise to a 3D structure, and in complex 2, four SCN ligands bridge [Hg(SCN) 4] 2- and [Mn(Im) 2] 2+ to form a 3D structure. The structure of 3 contains two copper atoms with distinct coordination environment; one is coordinated by four N-methyl-imidazole ligands and two axially elongated SCN groups, and another by four SCN groups (two elongated) and two N-methyl-imidazole ligands. The magnetic property of complex 1 has been investigated. The spin state structure in hetermetallic NiHgNi systems of complex 1 is irregular. The ESR spectra results of complex 3 demonstrate Cu 2+ ion lie on octahedral environment.

A unique role of RGS9-2 in the striatum as a positive or negative regulator of opiate analgesia.

PubMed

Psifogeorgou, Kassi; Psigfogeorgou, Kassi; Terzi, Dimitra; Papachatzaki, Maria Martha; Varidaki, Artemis; Ferguson, Deveroux; Gold, Stephen J; Zachariou, Venetia

2011-04-13

The signaling molecule RGS9-2 is a potent modulator of G-protein-coupled receptor function in striatum. Our earlier work revealed a critical role for RGS9-2 in the actions of the μ-opioid receptor (MOR) agonist morphine. In this study, we demonstrate that RGS9-2 may act as a positive or negative modulator of MOR-mediated behavioral responses in mice depending on the agonist administered. Paralleling these findings we use coimmunoprecipitation assays to show that the signaling complexes formed between RGS9-2 and Gα subunits in striatum are determined by the MOR agonist, and we identify RGS9-2 containing complexes associated with analgesic tolerance. In striatum, MOR activation promotes the formation of complexes between RGS9-2 and several Gα subunits, but morphine uniquely promotes an association between RGS9-2 and Gαi3. In contrast, RGS9-2/Gαq complexes assemble after acute application of several MOR agonists but not after morphine application. Repeated morphine administration leads to the formation of distinct complexes, which contain RGS9-2, Gβ5, and Gαq. Finally, we use simple pharmacological manipulations to disrupt RGS9-2 complexes formed during repeated MOR activation to delay the development of analgesic tolerance to morphine. Our data provide a better understanding of the brain-region-specific signaling events associated with opiate analgesia and tolerance and point to pharmacological approaches that can be readily tested for improving chronic analgesic responsiveness.

Organic derivatives of tin (II/IV): Investigation of their structure

NASA Astrophysics Data System (ADS)

Szirtes, L.; Megyeri, J.; Kuzmann, E.; Beck, A.

2011-07-01

The structures of tin(II)-oxalate, tin(IV)Na-EDTA and tin(IV)Na 8-inositol hexaphosphate were investigated using XRD analysis. Samples were identified using the Mössbauer study, thermal analysis and FTIR spectrometry. The Mössbauer study determined two different oxidation states of tin atoms, and consequently two different tin surroundings in the end products. The tin oxalate was found to be orthorhombic with space group Pnma, a=9.2066(3) Å, b=9.7590(1) Å, c=13.1848(5) Å, V=1184.62 Å 3 and Z=8. SnNa-EDTA was found to be monoclinic with space group P2 1/c 1, a=10.7544(3) Å, b=10.1455(3) Å, c=16.5130(6) Å, β=98.59(2)°, V=1781.50(4) Å 3 and Z=4. Sn(C 6H 6Na 8O 24P 6) was found to be amorphous.

27 CFR 6.72 - “Tie-in” sales.

Code of Federal Regulations, 2011 CFR

2011-04-01

... by an industry member of requiring that a retailer purchase one product (as defined in § 6.11) in... in some type of premium package, i.e., a distinctive decanter, or wooden or tin box. This also includes combination sales if one or more products may be purchased only in combination with other products...

27 CFR 6.72 - “Tie-in” sales.

Code of Federal Regulations, 2014 CFR

2014-04-01

... by an industry member of requiring that a retailer purchase one product (as defined in § 6.11) in... in some type of premium package, i.e., a distinctive decanter, or wooden or tin box. This also includes combination sales if one or more products may be purchased only in combination with other products...

27 CFR 6.72 - “Tie-in” sales.

Code of Federal Regulations, 2012 CFR

2012-04-01

... by an industry member of requiring that a retailer purchase one product (as defined in § 6.11) in... in some type of premium package, i.e., a distinctive decanter, or wooden or tin box. This also includes combination sales if one or more products may be purchased only in combination with other products...

Application of the Geo-Anomaly Unit Concept in Quantitative Delineation and Assessment of Gold Ore Targets in Western Shandong Uplift Terrain, Eastern China

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen Yongqing, E-mail: ydonglai@mail.cgs.gov.cn; Zhao Pengda; Chen Jianguo

2001-03-15

A number of large and giant ore deposits have been discovered within the relatively small areas of lithospheric structure anomalies, including various boundary zones of tectonic plates. The regions have become the well-known intercontinental ore-forming belts, such as the circum-Pacific gold-copper, copper-molybdenum, and tungsten-tin metallogenic belts. These belts are typical geological anomalous areas. An investigation into the hydrothermal ore deposits in different regions in the former Soviet Union illustrated that the geologic structures of ore fields of almost all major commercial deposits have distinct features compared with the neighboring areas. These areas with distinct features are defined as geo-anomalies. Amore » geo-anomaly refers to such a geologic body or a combination of bodies that their composition, texture-structure, and genesis are significantly different from those of their surroundings. A geo-anomaly unit (GU) is an area containing distinct features that can be delineated with integrated ore-forming information using computer techniques on the basis of the geo-anomaly concept. Herein, the GU concept is illustrated by a case study of delineating the gold ore targets in the western Shandong uplift terrain, eastern China. It includes: (1) analyses of gold ore-forming factors; (2) compilation of normalized regional geochemical map and extraction of geochemical anomalies; (3) compilation of gravitational and aeromagnetic tectonic skeleton map and extraction of gravitational and aeromagnetic anomalies; (4) extraction of circular and linear anomalies from remote-sensing Landsat TM images; (5) establishment of a geo-anomaly conceptual model associated with known gold mineralization; (6) establishment of gold ore-forming favorability by computing techniques; and (7) delineation and assessment of ore-forming units. The units with high favorability are suggested as ore targets.« less

Origin of the mysterious Yin-Shang bronzes in China indicated by lead isotopes.

PubMed

Sun, Wei-dong; Zhang, Li-peng; Guo, Jia; Li, Cong-ying; Jiang, Yu-hang; Zartman, Robert E; Zhang, Zhao-feng

2016-03-18

Fine Yin-Shang bronzes containing lead with puzzlingly highly radiogenic isotopic compositions appeared suddenly in the alluvial plain of the Yellow River around 1400 BC. The Tongkuangyu copper deposit in central China is known to have lead isotopic compositions even more radiogenic and scattered than those of the Yin-Shang bronzes. Most of the Yin-Shang bronzes are tin-copper alloys with high lead contents. The low lead and tin concentrations, together with the less radiogenic lead isotopes of bronzes in an ancient smelting site nearby, however, exclude Tongkuangyu as the sole supplier of the Yin-Shang bronzes. Interestingly, tin ingots/prills and bronzes found in Africa also have highly radiogenic lead isotopes, but it remains mysterious as to how such African bronzes may have been transported to China. Nevertheless, these African bronzes are the only bronzes outside China so far reported that have lead isotopes similar to those of the Yin-Shang bronzes. All these radiogenic lead isotopes plot along ~2.0-2.5 Ga isochron lines, implying that deposits around Archean cratons are the most likely candidates for the sources. African cratons along the Nile and even micro-cratons in the Sahara desert may have similar lead signatures. These places were probably accessible by ancient civilizations, and thus are the most favorable suppliers of the bronzes.

Low-temperature growth and electronic structures of ambipolar Yb-doped zinc tin oxide transparent thin films

NASA Astrophysics Data System (ADS)

Oh, Seol Hee; Ferblantier, Gerald; Park, Young Sang; Schmerber, Guy; Dinia, Aziz; Slaoui, Abdelilah; Jo, William

2018-05-01

The compositional dependence of the crystal structure, optical transmittance, and surface electric properties of the zinc tin oxide (Zn-Sn-O, shortened ZTO) thin films were investigated. ZTO thin films with different compositional ratios were fabricated on glass and p-silicon wafers using radio frequency magnetron sputtering. The binding energy of amorphous ZTO thin films was examined by a X-ray photoelectron spectroscopy. The optical transmittance over 70% in the visible region for all the ZTO films was observed. The optical band gap of the ZTO films was changed as a result of the competition between the Burstein-Moss effect and renormalization. An electron concentration in the films and surface work function distribution were measured by a Hall measurement and Kelvin probe force microscopy, respectively. The mobility of the n- and p-type ZTO thin films have more than 130 cm2/V s and 15 cm2/V s, respectively. We finally constructed the band structure which contains band gap, work function, and band edges such as valence band maximum and conduction band minimum of ZTO thin films. The present study results suggest that the ZTO thin film is competitive compared with the indium tin oxide, which is a representative material of the transparent conducting oxides, regarding optoelectronic devices applications.

Titanium nitride as a seed layer for Heusler compounds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niesen, Alessia, E-mail: aniesen@physik.uni-bielefeld.de; Glas, Manuel; Ludwig, Jana

Titanium nitride (TiN) shows low resistivity at room temperature (27 μΩ cm), high thermal stability and thus has the potential to serve as seed layer in magnetic tunnel junctions. High quality TiN thin films with regard to the crystallographic and electrical properties were grown and characterized by x-ray diffraction and 4-terminal transport measurements. Element specific x-ray absorption spectroscopy revealed pure TiN inside the thin films. To investigate the influence of a TiN seed layer on a ferro(i)magnetic bottom electrode in magnetic tunnel junctions, an out-of-plane magnetized Mn{sub 2.45}Ga as well as in- and out-of-plane magnetized Co{sub 2}FeAl thin films were depositedmore » on a TiN buffer, respectively. The magnetic properties were investigated using a superconducting quantum interference device and anomalous Hall effect for Mn{sub 2.45}Ga. Magneto optical Kerr effect measurements were carried out to investigate the magnetic properties of Co{sub 2}FeAl. TiN buffered Mn{sub 2.45}Ga thin films showed higher coercivity and squareness ratio compared to unbuffered samples. The Heusler compound Co{sub 2}FeAl showed already good crystallinity when grown at room temperature on a TiN seed-layer.« less

Tinless Solder Investigation

DTIC Science & Technology

1937-06-24

tin solder. 4. By soldering coated thin (.015*) plates of tin- plate, terne-plate and galvanised iron with this mixture, the tensile strength in...9700 lbs/ln2 Average 9500 lbs/ln2 •The plates used In this test were tin-plate. Tests on bright annealed, terne-plate, brass and galvanised ...plates (tin-plate, terne- plate and galvanised iron) had coatings, it was impossible to use emery oloth OB them to completely remove the rust or

40 CFR 63.3561 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... containers other than can ends. Decorative tin means a single-walled container, designed to be covered or... listed in 40 CFR 51.100(s). Food can means any can manufactured to contain edible products and designed... with the test methods specified in § 63.3521. Manufacturer's formulation data may include, but are not...

40 CFR 63.3561 - What definitions apply to this subpart?

Code of Federal Regulations, 2014 CFR

2014-07-01

... containers other than can ends. Decorative tin means a single-walled container, designed to be covered or... listed in 40 CFR 51.100(s). Food can means any can manufactured to contain edible products and designed... with the test methods specified in § 63.3521. Manufacturer's formulation data may include, but are not...

40 CFR 63.3561 - What definitions apply to this subpart?

Code of Federal Regulations, 2013 CFR

2013-07-01

... containers other than can ends. Decorative tin means a single-walled container, designed to be covered or... listed in 40 CFR 51.100(s). Food can means any can manufactured to contain edible products and designed... with the test methods specified in § 63.3521. Manufacturer's formulation data may include, but are not...

40 CFR 63.3561 - What definitions apply to this subpart?

Code of Federal Regulations, 2012 CFR

2012-07-01

... containers other than can ends. Decorative tin means a single-walled container, designed to be covered or... listed in 40 CFR 51.100(s). Food can means any can manufactured to contain edible products and designed... with the test methods specified in § 63.3521. Manufacturer's formulation data may include, but are not...

Nature of active tin species and promoting effect of nickle in silica supported tin oxide for dehydrogenation of propane

NASA Astrophysics Data System (ADS)

Wang, Haoren; Wang, Hui; Li, Xiuyi; Li, Chunyi

2017-06-01

Different with Wang et. al.'s study, we found that polymeric Si-O-Sn2+ rather than Ni-Sn alloy and metallic Sn are active species in silica-supported tin oxide catalysts for dehydrogenation of propane. The results showed that high surface area of mesoporous silica brought about high dispersion of tin oxide species, as a result, catalytic activity and stability were both improved. DRUV-vis, XPS, TPR and XRD studies of fresh and reduced catalysts indicated that the deactivation was related to the reduction of active species rather than the coke formation since active tin species cannot maintain its oxidation state at reaction conditions (high temperature and reducing atmosphere). The formed Ni3Sn2 alloy after reduction just functioned as promoter which accelerated the desorption of H2 and regeneration of active site. A synergy effect between active tin species and Ni3Sn2 alloy were observed.

Localized superconductivity in the quantum-critical region of the disorder-driven superconductor-insulator transition in TiN thin films.

PubMed

Baturina, T I; Mironov, A Yu; Vinokur, V M; Baklanov, M R; Strunk, C

2007-12-21

We investigate low-temperature transport properties of thin TiN superconducting films in the vicinity of the disorder-driven superconductor-insulator transition. In a zero magnetic field, we find an extremely sharp separation between superconducting and insulating phases, evidencing a direct superconductor-insulator transition without an intermediate metallic phase. At moderate temperatures, in the insulating films we reveal thermally activated conductivity with the magnetic field-dependent activation energy. At very low temperatures, we observe a zero-conductivity state, which is destroyed at some depinning threshold voltage V{T}. These findings indicate the formation of a distinct collective state of the localized Cooper pairs in the critical region at both sides of the transition.

UV-visible spectroscopic estimation of photodegradation of rhodamine-B dye using tin(IV) oxide nanoparticles.

PubMed

Sangami, G; Dharmaraj, N

2012-11-01

Nanocrystalline, tin(IV) oxide (SnO(2)) particles has been prepared by thermal decomposition of tin oxalate precursor obtained from the reactions of tin(IV) chloride and sodium oxalate using eggshell membrane (ESM). The as-prepared SnO(2) nanoparticles were characterized by thermal studies, transmission electron microscopy (TEM), powder X-ray diffraction (XRD), Raman, FT-IR and UV-visible studies and used as a photocatalyst for the degradation of rhodamine-B (Rh-B) dye. The size of the prepared nanoparticles was in the range of 5-12nm as identified from the TEM images. Powder XRD data revealed the presence of a tetragonal, rutile crystalline phase of the tin(IV) oxide nanoparticles. Thermal analysis showed that the decomposition of tin oxalate precursor to yield the titled tin(IV) oxide nanoparticles was completed below 500°C. The extent of degradation of Rh-B in the presence of SnO(2) monitored by absorption spectral measurements demonstrated that 94.48% of the selected dye was degraded upon irradiation with UV light for 60 min. Copyright © 2012 Elsevier B.V. All rights reserved.

Study on the removal of iron impurities in methanesulfonic acid tin plating bath

NASA Astrophysics Data System (ADS)

Hou-li, LIU; Jian-Jun, CHEN; Hong-Liang, PAN

2018-03-01

This thesis investigated the the influence of sodium sulfite as reducing agent on the recovery rate of tin ion. The approach is that HZ016 type cation exchange resin was used to adsorb Sn2+ and Fe2+ in electroplated tin solution first. After adsorption, the resin was removed by sulfuric acid, which was added with NaOH to adjust pH value to form precipitation and separate tin. X-ray diffraction (XRD) and energy spectrum (EDS) method were used to analyze the composition of the precipitates adjusted by pH. The results show that when the mass ratio of resin to bath is 1:2, the adsorption efficiency of resin reaches 98.3% and 97.1% respectively, and the elution efficiency of tin and iron reaches 95.1% and 94% respectively when the mass ratio of resin to eluent sulfuric acid is 1:4. Sodium sulfite was added to increase the efficiency of tin recovery by 8.1%. EDS and XRD atlas showed that after pH regulation, the main composition of the filtration precipitation was the hydroxides of tin.

Interactome Analyses of Mature γ-Secretase Complexes Reveal Distinct Molecular Environments of Presenilin (PS) Paralogs and Preferential Binding of Signal Peptide Peptidase to PS2*

PubMed Central

Jeon, Amy Hye Won; Böhm, Christopher; Chen, Fusheng; Huo, Hairu; Ruan, Xueying; Ren, Carl He; Ho, Keith; Qamar, Seema; Mathews, Paul M.; Fraser, Paul E.; Mount, Howard T. J.; St George-Hyslop, Peter; Schmitt-Ulms, Gerold

2013-01-01

γ-Secretase plays a pivotal role in the production of neurotoxic amyloid β-peptides (Aβ) in Alzheimer disease (AD) and consists of a heterotetrameric core complex that includes the aspartyl intramembrane protease presenilin (PS). The human genome codes for two presenilin paralogs. To understand the causes for distinct phenotypes of PS paralog-deficient mice and elucidate whether PS mutations associated with early-onset AD affect the molecular environment of mature γ-secretase complexes, quantitative interactome comparisons were undertaken. Brains of mice engineered to express wild-type or mutant PS1, or HEK293 cells stably expressing PS paralogs with N-terminal tandem-affinity purification tags served as biological source materials. The analyses revealed novel interactions of the γ-secretase core complex with a molecular machinery that targets and fuses synaptic vesicles to cellular membranes and with the H+-transporting lysosomal ATPase macrocomplex but uncovered no differences in the interactomes of wild-type and mutant PS1. The catenin/cadherin network was almost exclusively found associated with PS1. Another intramembrane protease, signal peptide peptidase, predominantly co-purified with PS2-containing γ-secretase complexes and was observed to influence Aβ production. PMID:23589300

Tin(II) alkoxide hydrolysis products for use as base catalysts

DOEpatents

Boyle, Timothy J.

2002-01-01

Tin alkoxide compounds are provided with accessible electrons. The compounds are a polymeric tin alkoxide, [Sn(OCH.sub.2 C(CH.sub.3).sub.3).sub.2 ].sub.n, and the hydrolysis products Sn.sub.6 O.sub.4 (OCH.sub.2 C(CH.sub.3).sub.3).sub.4 and Sn.sub.5 O.sub.2 (OCH.sub.2 C(CH.sub.3).sub.3).sub.6. The hydrolysis products are formed by hydrolyzing the [Sn(OCH.sub.2 C(CH.sub.3).sub.3).sub.2 ].sub.n in a solvent with controlled amounts of water, between 0.1 and 2 moles of water per mole of the polymeric tin alkoxide.

Tumor-infiltrating neutrophils predict benefit from adjuvant chemotherapy in patients with muscle invasive bladder cancer.

PubMed

Zhou, Lin; Xu, Le; Chen, Lingli; Fu, Qiang; Liu, Zheng; Chang, Yuan; Lin, Zongming; Xu, Jiejie

2017-01-01

Growing evidence shows tumor-infiltrating neutrophils (TINs) involvement in tumorigenesis. The objective of this study is to assess the prognostic effect of TINs and its impact on adjuvant chemotherapy benefits in muscle invasive bladder cancer (MIBC). A total of 142 MIBC patients from Zhongshan Hospital, 119 MIBC patients from FUSCC, and 405 MIBC patients from TCGA cohort were enrolled in the study. TINs were evaluated by immunohistochemical staining of CD66b or the CIBERSORT method. Patients with high TINs had a significantly poorer overall survival ( p = 0.001, p < 0.001, and p = 0.002, respectively) in the three sets. In the multivariate analysis, the presence of high TINs (HR = 2.122, p = 0.007; HR = 3.807, p < 0.001; HR = 2.104, p = 0.001; respectively) was identified as an independent prognostic factor for overall survival in the three sets. More importantly, Low TINs patients had significantly longer overall survival in patients without ACT in the three sets. Gene set enrichment analysis showed that lymphocyte activation ( p < 0.001) and T cell activation ( p = 0.008) were significantly enriched in the low TINs group. In addition, TINs were negatively correlated with CD8 + T cells, suggesting that the status of high-TINs was linked to the status of immunosuppression in MIBC. TINs could be used as independent prognostic factor. Low TINs identified a subgroup of MIBC patients who appeared to benefit from adjuvant chemotherapy. Incorporation of TINs into TNM system could further stratify patients with different prognosis.

Tumor-infiltrating neutrophils predict benefit from adjuvant chemotherapy in patients with muscle invasive bladder cancer

PubMed Central

Zhou, Lin; Xu, Le; Chen, Lingli; Fu, Qiang; Liu, Zheng; Chang, Yuan; Lin, Zongming; Xu, Jiejie

2017-01-01

ABSTRACT Growing evidence shows tumor-infiltrating neutrophils (TINs) involvement in tumorigenesis. The objective of this study is to assess the prognostic effect of TINs and its impact on adjuvant chemotherapy benefits in muscle invasive bladder cancer (MIBC). A total of 142 MIBC patients from Zhongshan Hospital, 119 MIBC patients from FUSCC, and 405 MIBC patients from TCGA cohort were enrolled in the study. TINs were evaluated by immunohistochemical staining of CD66b or the CIBERSORT method. Patients with high TINs had a significantly poorer overall survival (p = 0.001, p < 0.001, and p = 0.002, respectively) in the three sets. In the multivariate analysis, the presence of high TINs (HR = 2.122, p = 0.007; HR = 3.807, p < 0.001; HR = 2.104, p = 0.001; respectively) was identified as an independent prognostic factor for overall survival in the three sets. More importantly, Low TINs patients had significantly longer overall survival in patients without ACT in the three sets. Gene set enrichment analysis showed that lymphocyte activation (p < 0.001) and T cell activation (p = 0.008) were significantly enriched in the low TINs group. In addition, TINs were negatively correlated with CD8+ T cells, suggesting that the status of high-TINs was linked to the status of immunosuppression in MIBC. TINs could be used as independent prognostic factor. Low TINs identified a subgroup of MIBC patients who appeared to benefit from adjuvant chemotherapy. Incorporation of TINs into TNM system could further stratify patients with different prognosis. PMID:28507798

Kinetics study of Jatropha oil esterification with ethanol in the presence of tin (II) chloride catalyst for biodiesel production

NASA Astrophysics Data System (ADS)

Kusumaningtyas, Ratna Dewi; Ratrianti, Naomi; Purnamasari, Indah; Budiman, Arief

2017-01-01

Jatropha oil is one of the promising feedstocks for biodiesel production. Jatropha oil is non-edible oil hence utilization of this oil would not compete with the needs of food. However, crude jatropha oil usually has high free fatty acid (FFA) content. Due to this fact, direct alkaline-catalyzed transesterification of crude jatropha oil for biodiesel production cannot be performed. FFA in crude jatropha oil will react with a base catalyst, resulting in soap as by product and hindering methyl ester (biodiesel) production. Therefore, prior to a transesterification reaction, it is crucial to run a pretreatment step of jatropha oil which can lower the FFA content in the oil. In this work, the pretreatment process was conducted through the esterification reaction of FFA contained in crude jatropha oil with ethanol over tin (II) chloride catalyst to reduce the acid value of the feedstock. The feedstock was Indonesia crude jatropha oil containing 12.03% of FFA. The esterification reaction was carried out in a batch reactor with a molar ratio of FFA to ethanol was 1:60 and total reaction time was 180 minutes. Tin (II) chloride catalyst was varied at 2.5, 5, 7.5, and 10% wt, whereas the effect of the reaction temperature was studied at 35, 34, 55, and 65 °C. The best reaction conversion was 71.55%, achieved at the following condition: a reaction temperature of 65 °C, catalyst concentration of 10% wt, the reaction time of 180 min, and the molar ratio of FFA to ethanol was 1:60. Kinetics study was also conducted in this work. It was found that esterification reaction of jatropha oil FFA with ethanol catalyzed by tin(II) chloride fitted the first-order pseudo-homogeneous kinetics model. It was also revealed that the frequency factor (A) and the activation energy (Ea) were 4.3864 × 106 min-1 and 56.2513 kJ/mole, respectively.

Web life: ComplexityBlog.com

NASA Astrophysics Data System (ADS)

2010-02-01

The site's homepage calls it "a repository of ideas and perspectives regarding the science, engineering and philosophy of complexity", and it pretty much does what it says on the tin. Part blog, part links archive, part library of modelling tips and tricks, the site is chock full of information that comes under the general heading of "complexity".

77 FR 13156 - Carolina Power & Light Company; Shearon Harris Nuclear Power Plant, Unit 1; Exemption

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-05

... percent) and niobium (~1 percent). The elimination of tin has resulted in superior corrosion resistance and reduced irradiation-induced growth relative to both standard zircaloy (1.7 percent tin) and low-tin zircaloy (1.2 percent tin). The addition of niobium increases ductility, which is desirable to...

Influence of Microstructure on the Electrical Properties of Heteroepitaxial TiN Films

NASA Astrophysics Data System (ADS)

Xiang, Wenfeng; Liu, Yuan; Zhang, Jiaqi

2018-05-01

Heteroepitaxial TiN films were deposited on Si substrates by pulse laser deposition at different substrate temperature. The microstructure and surface morphology of the films were investigated by X-ray diffraction (θ-2θ scan, ω-scan, and ϕ-scan) and atomic force microscopy. The electrical properties of the prepared TiN films were studied using a physical property measurement system. The experimental results showed that the crystallinity and surface morphology of the TiN films were improved gradually with increasing substrate temperature below 700 °C. Specially, single crystal TiN films were prepared when substrate temperature is above 700 °C; However, the quality of TiN films gradually worsened when the substrate temperature was increased further. The electrical properties of the films were directly correlated to their crystalline quality. At the optimal substrate temperature of 700 °C, the TiN films exhibited the lowest resistivity and highest mobility of 25.7 μΩ cm and 36.1 cm2/V s, respectively. In addition, the mechanism concerning the influence of substrate temperature on the microstructure of TiN films is discussed in detail.

From toothpaste to topological insulators and materials for valleytronics: The journeys of fluorinated tin

NASA Astrophysics Data System (ADS)

Barraza-Lopez, Salvador; Rivero, Pablo; Yan, Jia-An; Garcia-Suarez, Victor Manuel; Ferrer, Jaime

2015-03-01

Tin fluoride has a vast literature. This material is stable in bulk form at room temperature and has commercial applications that include fluorinated toothpaste. Bulk tin fluoride has a pair of fluorine atoms bridging two tin atoms. In the recent past the electronic properties of 2D tin with honeycomb structure have been discussed thus generating a wealth of literature that emphasizes its non-topologically-trivial electronic properties due to the combination of a Dirac-like dispersion and a strong spin-orbit coupling given its large atomic mass. Nevertheless the stability of such freestanding structures has been contested recently. As it turns out, the most stable form of fluorinated tin does not possess a graphane-like structure either. In the most stable phase to be discussed here, fluorine atoms tilt away from (graphane-like) positions over/below tin atoms; in an atomistic arrangement similar to the one seen on their parent bulk structure. Electronic properties depend on atomistic coordination, and the most stable form of fluorinated tin does not possess non-trivial topological properties. Nevertheless it represents a new paradigm for valleytronics in 2D.

Synthesis, structures, and electroluminescent properties of scandium N,O-chelated complexes toward near-white organic light-emitting diodes.

PubMed

Katkova, Marina A; Balashova, Tatyana V; Ilichev, Vasilii A; Konev, Alexey N; Isachenkov, Nikolai A; Fukin, Georgy K; Ketkov, Sergey Yu; Bochkarev, Mikhail N

2010-06-07

Three members of a new class of electroluminescent, neutral, and monomeric scandium N,O-chelate complexes, namely, Sc(III)-tris-2-(2-benzoimidazol-2-yl)phenolate (1), Sc(III)-tris-2-(2-benzoxyazol-2-yl)phenolate (2), and Sc(III)-tris-2-(2-benzothiazol-2-yl)phenolate (3), have been prepared and X-ray characterized. DFT calculations have been performed. In contrast to the most frequently applied dual or multiple dopants in multilayer white OLED devices, all our simpler devices with the configuration of indium tin oxide/N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine/neat scandium complex/Yb exhibit close to near-white emission with a blue hue (CIE(x,y) = 0.2147, 0.2379) in the case of 1, a cyan hue (0.2702, 0.3524) in the case of 2, and a yellowish hue (0.3468; 0.4284) in the case of 3.

A facile way to control phase of tin selenide flakes by chemical vapor deposition

NASA Astrophysics Data System (ADS)

Wang, Zhigang; Pang, Fei

2018-06-01

Although two-dimensional (2D) tin selenides are attracting intense attentions, studies on its phase transition are still relatively few. Here we report a facile way to control the phase growth of tin selenide flakes on mica and SiO2/Si by only adjusting nominal Sn:Se ratio, which refers to the amount of loaded SnO2 and Se precursors. High normal Sn:Se ratio induced SnSe flakes, conversely SnSe2 flakes formed. It could be used as a practical guide to selectively synthesize pure phase of single crystalline 2D layered chalcogenide materials similar to tin selenides.

Parallelization of a Fully-Distributed Hydrologic Model using Sub-basin Partitioning

NASA Astrophysics Data System (ADS)

Vivoni, E. R.; Mniszewski, S.; Fasel, P.; Springer, E.; Ivanov, V. Y.; Bras, R. L.

2005-12-01

A primary obstacle towards advances in watershed simulations has been the limited computational capacity available to most models. The growing trend of model complexity, data availability and physical representation has not been matched by adequate developments in computational efficiency. This situation has created a serious bottleneck which limits existing distributed hydrologic models to small domains and short simulations. In this study, we present novel developments in the parallelization of a fully-distributed hydrologic model. Our work is based on the TIN-based Real-time Integrated Basin Simulator (tRIBS), which provides continuous hydrologic simulation using a multiple resolution representation of complex terrain based on a triangulated irregular network (TIN). While the use of TINs reduces computational demand, the sequential version of the model is currently limited over large basins (>10,000 km2) and long simulation periods (>1 year). To address this, a parallel MPI-based version of the tRIBS model has been implemented and tested using high performance computing resources at Los Alamos National Laboratory. Our approach utilizes domain decomposition based on sub-basin partitioning of the watershed. A stream reach graph based on the channel network structure is used to guide the sub-basin partitioning. Individual sub-basins or sub-graphs of sub-basins are assigned to separate processors to carry out internal hydrologic computations (e.g. rainfall-runoff transformation). Routed streamflow from each sub-basin forms the major hydrologic data exchange along the stream reach graph. Individual sub-basins also share subsurface hydrologic fluxes across adjacent boundaries. We demonstrate how the sub-basin partitioning provides computational feasibility and efficiency for a set of test watersheds in northeastern Oklahoma. We compare the performance of the sequential and parallelized versions to highlight the efficiency gained as the number of processors increases. We also discuss how the coupled use of TINs and parallel processing can lead to feasible long-term simulations in regional watersheds while preserving basin properties at high-resolution.

In vivo biochemical analyses reveal distinct roles of β-importins and eEF1A in tRNA subcellular traffic

PubMed Central

Huang, Hsiao-Yun

2015-01-01

Bidirectional tRNA movement between the nucleus and the cytoplasm serves multiple biological functions. To gain a biochemical understanding of the mechanisms for tRNA subcellular dynamics, we developed in vivo β-importin complex coimmunoprecipitation (co-IP) assays using budding yeast. Our studies provide the first in vivo biochemical evidence that two β-importin family members, Los1 (exportin-t) and Msn5 (exportin-5), serve overlapping but distinct roles in tRNA nuclear export. Los1 assembles complexes with RanGTP and tRNA. Both intron-containing pre-tRNAs and spliced tRNAs, regardless of whether they are aminoacylated, assemble into Los1–RanGTP complexes, documenting that Los1 participates in both primary nuclear export and re-export of tRNAs to the cytoplasm. In contrast, β-importin Msn5 preferentially assembles with RanGTP and spliced, aminoacylated tRNAs, documenting its role in tRNA nuclear re-export. Tef1/2 (the yeast form of translation elongation factor 1α [eEF1A]) aids the specificity of Msn5 for aminoacylated tRNAs to form a quaternary complex consisting of Msn5, RanGTP, aminoacylated tRNA, and Tef1/2. Assembly and/or stability of this quaternary complex requires Tef1/2, thereby facilitating efficient re-export of aminoacylated tRNAs to the cytoplasm. PMID:25838545

Core-shell titanium dioxide-titanium nitride nanotube arrays with near-infrared plasmon resonances

NASA Astrophysics Data System (ADS)

Farsinezhad, Samira; Shanavas, Thariq; Mahdi, Najia; Askar, Abdelrahman M.; Kar, Piyush; Sharma, Himani; Shankar, Karthik

2018-04-01

Titanium nitride (TiN) is a ceramic with high electrical conductivity which in nanoparticle form, exhibits localized surface plasmon resonances (LSPRs) in the visible region of the solar spectrum. The ceramic nature of TiN coupled with its dielectric loss factor being comparable to that of gold, render it attractive for CMOS polarizers, refractory plasmonics, surface-enhanced Raman scattering and a whole host of sensing applications. We report core-shell TiO2-TiN nanotube arrays exhibiting LSPR peaks in the range 775-830 nm achieved by a simple, solution-based, low cost, large area-compatible fabrication route that does not involve laser-writing or lithography. Self-organized, highly ordered TiO2 nanotube arrays were grown by electrochemical anodization of Ti thin films on fluorine-doped tin oxide-coated glass substrates and then conformally coated with a thin layer of TiN using atomic layer deposition. The effects of varying the TiN layer thickness and thermal annealing on the LSPR profiles were also investigated. Modeling the TiO2-TiN core-shell nanotube structure using two different approaches, one employing effective medium approximations coupled with Fresnel coefficients, resulted in calculated optical spectra that closely matched the experimentally measured spectra. Modeling provided the insight that the observed near-infrared resonance was not collective in nature, and was mainly attributable to the longitudinal resonance of annular nanotube-like TiN particles redshifted due to the presence of the higher permittivity TiO2 matrix. The resulting TiO2-TiN core-shell nanotube structures also function as visible light responsive photocatalysts, as evidenced by their photoelectrochemical water-splitting performance under light emitting diode illumination using 400, 430 and 500 nm photons.

Confinement of β1- and β2-adrenergic receptors in the plasma membrane of cardiomyocyte-like H9c2 cells is mediated by selective interactions with PDZ domain and A-kinase anchoring proteins but not caveolae

PubMed Central

Valentine, Cathleen D.; Haggie, Peter M.

2011-01-01

The sympathetic nervous system regulates cardiac output by activating adrenergic receptors (ARs) in cardiac myocytes. The predominant cardiac ARs, β1- and β2AR, are structurally similar but mediate distinct signaling responses. Scaffold protein–mediated compartmentalization of ARs into discrete, multiprotein complexes has been proposed to dictate differential signaling responses. To test the hypothesis that βARs integrate into complexes in live cells, we measured receptor diffusion and interactions by single-particle tracking. Unstimulated β1- and β2AR were highly confined in the membrane of H9c2 cardiomyocyte-like cells, indicating that receptors are tethered and presumably integrated into protein complexes. Selective disruption of interactions with postsynaptic density protein 95/disks large/zonula occludens-1 (PDZ)–domain proteins and A-kinase anchoring proteins (AKAPs) increased receptor diffusion, indicating that these scaffold proteins participate in receptor confinement. In contrast, modulation of interactions between the putative scaffold caveolae and β2AR did not alter receptor dynamics, suggesting that these membrane domains are not involved in β2AR confinement. For both β1- and β2AR, the receptor carboxy-terminus was uniquely responsible for scaffold interactions. Our data formally demonstrate that distinct and stable protein complexes containing β1- or β2AR are formed in the plasma membrane of cardiomyocyte-like cells and that selective PDZ and AKAP interactions are responsible for the integration of receptors into complexes. PMID:21680711

Confinement of β(1)- and β(2)-adrenergic receptors in the plasma membrane of cardiomyocyte-like H9c2 cells is mediated by selective interactions with PDZ domain and A-kinase anchoring proteins but not caveolae.

PubMed

Valentine, Cathleen D; Haggie, Peter M

2011-08-15

The sympathetic nervous system regulates cardiac output by activating adrenergic receptors (ARs) in cardiac myocytes. The predominant cardiac ARs, β(1)- and β(2)AR, are structurally similar but mediate distinct signaling responses. Scaffold protein-mediated compartmentalization of ARs into discrete, multiprotein complexes has been proposed to dictate differential signaling responses. To test the hypothesis that βARs integrate into complexes in live cells, we measured receptor diffusion and interactions by single-particle tracking. Unstimulated β(1)- and β(2)AR were highly confined in the membrane of H9c2 cardiomyocyte-like cells, indicating that receptors are tethered and presumably integrated into protein complexes. Selective disruption of interactions with postsynaptic density protein 95/disks large/zonula occludens-1 (PDZ)-domain proteins and A-kinase anchoring proteins (AKAPs) increased receptor diffusion, indicating that these scaffold proteins participate in receptor confinement. In contrast, modulation of interactions between the putative scaffold caveolae and β(2)AR did not alter receptor dynamics, suggesting that these membrane domains are not involved in β(2)AR confinement. For both β(1)- and β(2)AR, the receptor carboxy-terminus was uniquely responsible for scaffold interactions. Our data formally demonstrate that distinct and stable protein complexes containing β(1)- or β(2)AR are formed in the plasma membrane of cardiomyocyte-like cells and that selective PDZ and AKAP interactions are responsible for the integration of receptors into complexes.

26 CFR 31.3406-0 - Outline of the backup withholding regulations.

Code of Federal Regulations, 2013 CFR

2013-04-01

... incorrect name/TIN combination. (2) Definition of account. (3) Definition of business day. (4) Certain exceptions. (c) Notice regarding an incorrect name/TIN combination. (1) In general. (2) Additional... of receipt. (d) Notice from payors of backup withholding due to an incorrect name/TIN combination. (1...

Speciation and Characterization of E-Waste, Using Analytical Techniques

NASA Astrophysics Data System (ADS)

López, C. Cortés; Cruz, V. E. Reyes; Rodríguez, M. A. Veloz; Ávila, J. Hernández; Badillo, J. Flores; Murcia, J. A. Cobos

Electronic waste (e-waste), have a high potential as a source of precious metals, since they can contain metals like silver, gold, platinum, copper, zinc, nickel, tin and others. In this paper some e-waste were characterized using several analytical techniques as Scanning Electron Microscopy (SEM), X-ray diffraction (XRD) and inductively coupled plasma (ICP) in addition to the thermodynamic study by Pourbaix diagrams of silver (Ag), gold (Au), platinum (Pt), copper (Cu), nickel (Ni), tin (Sn) and zinc (Zn); considering an average low concentration of HNO3 (10% v/v). With results of the characterization was determined that the e-waste is an ideal source for the recovery of valuable metals. Similarly, the thermodynamic studies showed that it is possible to obtain all metallic species except Pt, in a potential window of 1.45V to 2.0V vs SCE.

Effect of protective release coatings on the basis of superdispersersed zirconium oxide powder on the formation of gas defects in bronze casting

NASA Astrophysics Data System (ADS)

Martyushev, Nikita V.; Risto, Nikolay A.

2014-10-01

This paper investigates the use of nanopowders in the composition of foundry coatings when casting leaded tin bronzes. Influence of the composition of the applied protective coating on surface finish is studied. The effects of the coatings of the following compositions are compared: non-stick coating (a mixture of low-dispersed chromium oxide powder and heat-treated vegetable oil); non-stick lubricant ASPF-2/RgU on the basis of low- dispersed graphite powder and heat-treated vegetable oil; patent #2297300 (a mixture of superdispersed zirconium dioxide powder with industrial oil). It is demonstrated that application of foundry coatings containing superdispersed metal oxide powders with low thermal conductivity makes it possible to significantly reduce irregularities and eliminate gas porosity on the surface of tin-leaded bronze castings.

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

NASA Astrophysics Data System (ADS)

Lee, Mun Hyung; Park, Joo Hyun

2018-06-01

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When Δ T TiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the `Ostwald ripening model' based on the Lifshitz-Slyozov-Wagner theory in conjunction with the `Diffusion controlled model' using Ohnaka's microsegregation equation.

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

NASA Astrophysics Data System (ADS)

Lee, Mun Hyung; Park, Joo Hyun

2018-03-01

The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ΔT TiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the `Ostwald ripening model' based on the Lifshitz-Slyozov-Wagner theory in conjunction with the `Diffusion controlled model' using Ohnaka's microsegregation equation.

Synchrotron radiation x-ray photoelectron spectroscopy study on the interface chemistry of high-k PrxAl2-xO3 (x=0-2) dielectrics on TiN for dynamic random access memory applications

NASA Astrophysics Data System (ADS)

Schroeder, T.; Lupina, G.; Sohal, R.; Lippert, G.; Wenger, Ch.; Seifarth, O.; Tallarida, M.; Schmeisser, D.

2007-07-01

Engineered dielectrics combined with compatible metal electrodes are important materials science approaches to scale three-dimensional trench dynamic random access memory (DRAM) cells. Highly insulating dielectrics with high dielectric constants were engineered in this study on TiN metal electrodes by partly substituting Al in the wide band gap insulator Al2O3 by Pr cations. High quality PrAlO3 metal-insulator-metal capacitors were processed with a dielectric constant of 19, three times higher than in the case of Al2O3 reference cells. As a parasitic low dielectric constant interface layer between PrAlO3 and TiN limits the total performance gain, a systematic nondestructive synchrotron x-ray photoelectron spectroscopy study on the interface chemistry of PrxAl2-xO3 (x =0-2) dielectrics on TiN layers was applied to unveil its chemical origin. The interface layer results from the decreasing chemical reactivity of PrxAl2-xO3 dielectrics with increasing Pr content x to reduce native Ti oxide compounds present on unprotected TiN films. Accordingly, PrAlO3 based DRAM capacitors require strict control of the surface chemistry of the TiN electrode, a parameter furthermore of importance to engineer the band offsets of PrxAl2-xO3/TiN heterojunctions.

Highly patterned growth of SnO2 nanowires using a sub-atmospheric vapor-liquid-solid deposition

NASA Astrophysics Data System (ADS)

Akbari, M.; Mohajerzadeh, S.

2017-08-01

We report the realization of tin-oxide nanowires on patterned structures using a vapor-liquid-solid (VLS) process. While gold acts as the catalyst for the growth of wires, a tin-oxide containing sol-gel solution is spin coated on silicon substrate to act as the source for SnO vapor. The growth of tin-oxide nano-structures occurs mostly at the vicinity of the pre-deposited solution. By patterning the gold as the catalyst material, one is able to observe the growth at desired places. The growth of nanowires is highly dense within 100 µm away from such in situ source and their length is of the order of 5 µm. By further distancing from the source, the growth becomes more limited and nanowires become shorter and more sparsely distributed. The growth of nanowires has been studied using scanning and transmission electron microscopy tools while their composition has been investigated using XRD and EDS analyses. As a novel application, we have employed the grown nanowires as electron detection elements to measure the emitted electrons from electron sources. This configuration can be further used as electron detectors for scanning electron microscopes.

An Empirical Model for Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim; Wright, Clara; Asfour, Shihab; Onar, Arzu; Bayliss, Jon; Ludwig, Larry

2009-01-01

In this experiment, an empirical model to quantify the probability of occurrence of an electrical short circuit from tin whiskers as a function of voltage was developed. This empirical model can be used to improve existing risk simulation models. FIB and TEM images of a tin whisker confirm the rare polycrystalline structure on one of the three whiskers studied. FIB cross-section of the card guides verified that the tin finish was bright tin.

The measurement of radiation exposure of astronauts by radiochemical techniques

NASA Technical Reports Server (NTRS)

Brodzinski, R. L.

1971-01-01

The concentrations of 23 major, minor, and trace elements in the fecal samples from the Apollo 12 and 13 astronauts are reported. Most elemental excretion rates are comparable to rates reported for earlier missions. Exceptions are noted for calcium, iron, and tin. Body calcium and iron losses appear to be reduced during the Apollo 12 and 13 missions such that losses now seem to be insignificant. Refined measurements of tin excretion rates agree with normal dietary intakes. Earlier reported tin values are in error. A new passive dosimetry canister was designed which contains foils of tantalum, copper, titanium, iron, cobalt, aluminum, and scandium. By measuring the concentrations of the various products of nuclear reactions in these metals after space exposure, the characteristics of the incident cosmic particles can be determined.

The complex metal-rich boride Ti1+xRh2-x+yIr3-yB3 (x=0.68, y=1.06) with a new structure type containing B4 zigzag fragments: Synthesis, crystal chemistry and theoretical calculations

NASA Astrophysics Data System (ADS)

Goerens, Christian; Fokwa, Boniface P. T.

2012-08-01

Polycrystalline samples and single crystals of the new complex boride Ti1+xRh2-x+yIr3-yB3 (x=0.68; y=1.06) were synthesized by arc-melting the elements in a water-cooled copper crucible under an argon atmosphere and characterized by X-Ray diffraction as well as EDX measurements. The crystal structure was refined on the basis of single crystal data. The new phase, which represents a new structure type containing trans zigzag B4 fragments as well as isolated boron atoms crystallizes in the orthorhombic space group Pbam (Nr. 55) with the lattice parameters a=8.620(1) Å, b=14.995(2) Å and c=3.234(1) Å. First-principles density functional theory calculations using the Vienna ab-initio simulation package (VASP) were performed on an appropriate structural model (using a supercell approach) and the experimental crystallographic data could be reproduced accurately. Based on this model, the density of states and crystal orbital Hamilton population (for bonding analysis) were calculated, using the linear muffin-tin orbital atomic sphere approximation (LMTO-ASA) method. According to these calculations, this metal-rich compound should be metallic, as expected. Furthermore, very strong boron-boron interactions are observed in the trans zigzag B4 fragment, which induce a clear differentiation of two types of metal-boron contacts with different strength. The observed three-dimensional metal-metal interaction is in good agreement with the predicted metallic behavior.

40 CFR 437.44 - Effluent limitations attainable by the application of the best available technology economically...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2... Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2) The in-plant limitations that apply to metal... parameters Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium...

40 CFR 437.44 - Effluent limitations attainable by the application of the best available technology economically...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2... Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2) The in-plant limitations that apply to metal... parameters Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium...

40 CFR 437.44 - Effluent limitations attainable by the application of the best available technology economically...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2... Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2) The in-plant limitations that apply to metal... parameters Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium...

40 CFR 437.44 - Effluent limitations attainable by the application of the best available technology economically...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2... Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2) The in-plant limitations that apply to metal... parameters Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium...

40 CFR 437.44 - Effluent limitations attainable by the application of the best available technology economically...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2... Lead Mercury Nickel Silver Tin Titanium Vanadium Zinc (2) The in-plant limitations that apply to metal... parameters Antimony Arsenic Cadmium Chromium Cobalt Copper Lead Mercury Nickel Silver Tin Titanium Vanadium...

Direct observation of MoO 2 crystal growth from amorphous MoO 3 film

NASA Astrophysics Data System (ADS)

Nina, Kenji; Kimura, Yuki; Yokoyama, Kaori; Kido, Osamu; Binyo, Gong; Kaito, Chihiro

2008-08-01

The formation process of MoO 2 crystal from amorphous MoO 3 film has been imaged by in situ observation with a transmission electron microscope. Selective growth of flower-shaped MoO 2 crystals by heating above 673 K in vacuum was directly observed. Since the MoO 2 crystal has metallic conductivity of the order of indium oxide film containing tin (ITO film), the thin film growth of the MoO 2 phase has been discussed on the basis of a new substitute for ITO film.

Core Temperature Measurement During Submaximal Exercise: Esophageal, Rectal, and Intestinal Temperatures

NASA Technical Reports Server (NTRS)

Lee, Stuart M. C.; Williams, W. Jon; Schneider, Suzanne M.

2000-01-01

The purpose of this study was to determine if intestinal temperature (Tin) might be in acceptable alternative to esophageal (Tes) and rectal temperature (Trec) to assess thermoregulation during supine exercise. We hypothesized that Tin would have values similar to Tes and a response time similar to Trec, but the rate of temperature change across time would not be different between measurement sites. Seven subjects completed a continuous supine protocol of 20 min of rest, 20 min of cycle exercise at 40% peak oxygen consumption (VO2pk), 20 min of cycle exercise at 65% V02pk, and 20 min of recovery. Tes, Trec, and Tin were recorded each min throughout the test. Temperatures were not different after 20 min of rest, but Trec was less than the Tes and Tin at the end of the 40% and 65% VO2pk stages. After 20 min of recovery, Tes was less than either Trec or Tin, which were not different from each other. Time to threshold for increased temperature from rest was greater for Trec than Tes but not different from Tin. Time to reach peak temperature was greater for Tin and Trec than Tes. Similarly, time to a decrease in temperature after exercise was greater for Trec than Tes, but not different from Tin. The rate of temperature change from threshold to the end of the 40% VO2pk stage was not different between measurement sites. However, the rate of change during recovery was more negative for Tes than Tin and Trec, which were different from each other. Measurement of Tin may he an acceptable alternative to Tes and Trec with an understanding of its limitations.

Experimental Study on the Behavior of TiN and Ti2O3 Inclusions in Contact with CaO‐Al2O3‐SiO2‐MgO Slags

PubMed Central

Bernhard, C.

2017-01-01

TiN and Ti2O3 are the predominant inclusion types in Ti-alloyed ferritic chromium stainless steels. In order to ensure the required steel cleanness level, an effective removal of such inclusions in the slag during secondary metallurgy is essential. This inclusion removal predominantly takes place via dissolution of the inclusion in the slag. The dissolution behavior of TiN and Ti2O3 in CaO-SiO2-Al2O3-MgO slags as well as their agglomeration behavior in the liquid steel is investigated using High Temperature Laser Scanning Confocal Microscopy and Tammann Furnace experiments. Thermodynamic calculations are performed using FactSage 7.0. The behavior of TiN is observed to be completely different to that of oxides. Ti2O3 dissolves quickly in slags, and its dissolution behavior is comparable to that of other already well examined oxides. In contrast, TiN shows a very intense gas reaction which is attributed to the release of nitrogen during contact with slag. Slags with higher SiO2 content show a significantly higher ability for the dissolution of TiN as compared to Al2O3-rich slags. The gas reaction is found to also significantly influence the final steel cleanness. Despite the easy absorption of TiN in the slag, the formed nitrogen supports the formation of pinholes in the steel. PMID:29109805

Semimicrodetermination of combined tantalum and niobium with selenous acid

USGS Publications Warehouse

Grimaldi, F.S.; Schnepfe, M.

1959-01-01

Tantalum and niobium are separated and determined gravimetrically by precipitation with selenous acid from highly acidic solutions in the absence of complexing agents. Hydrogen peroxide is used in the preparation of the solution and later catalytically destroyed during digestion of the precipitate. From 0.2 to 30 mg., separately or in mixtures, of niobium or tantalum pentoxide can be separated from mixtures containing 100 mg. each of the oxides of scandium, yttrium, cerium, vanadium, molybdenum, iron, aluminum, tin, lead, and bismuth with a single precipitation; and from 30 mg. of titanium dioxide, and 50 mg. each of the oxides of antimony and thorium, when present separately, with three precipitations. At least 50 mg. of uranium(VI) oxide can be separated with a single precipitation when present alone; otherwise, three precipitations may be needed. Zirconium does not interfere when the tantalum and niobium contents of the sample are small, but in general, zirconium as well as tungsten interfere. The method is applied to the determination of the earth acids in tantaloniobate ores.

Insights into the intramolecular donor stabilisation of organostannylene palladium and platinum complexes: syntheses, structures and DFT calculations.

PubMed

Wagner, Michael; Deáky, Vajk; Dietz, Christina; Martincová, Jana; Mahieu, Bernard; Jambor, Roman; Herres-Pawlis, Sonja; Jurkschat, Klaus

2013-05-17

The syntheses of the transition metal complexes cis-[(4-tBu-2,6-{P(O)(OiPr)2}2C6H2SnCl)2MX2] (1, M = Pd, X = Cl; 2, M = Pd, X = Br; 3, M = Pd, X = I; 4, M = Pt, X = Cl), cis-[{2,6-(Me2NCH2)2C6H3SnCl}2MX2] (5, M = Pd, X = I; 6, M = Pt, X = Cl), trans-[{2,6-(Me2NCH2)2C6H3SnI}2PtI2] (7) and trans-[(4-tBu-2,6-{P(O)(OiPr)2}2C6H2SnCl)PdI2]2 (8) are reported. Also reported is the serendipitous formation of the unprecedented complexes trans-[(4-tBu-2,6-{P(O)(OiPr)2}2C6H2SnCl)2Pt(SnCl3)2] (10) and [(4-tBu-2,6-{P(O)(OiPr)2}2C6H2SnCl)3Pt(SnCl3)2] (11). The compounds were characterised by elemental analyses, (1)H, (13)C, (31)P, (119)Sn and (195)Pt NMR spectroscopy, single-crystal X-ray diffraction analysis, UV/Vis spectroscopy and, in the cases of compounds 1, 3 and 4, also by Mössbauer spectroscopy. All the compounds show the tin atoms in a distorted trigonal-bipyramidal environment. The Mössbauer spectra suggest the tin atoms to be present in the oxidation state III. The kinetic lability of the complexes was studied by redistribution reactions between compounds 1 and 3 as well as between 1 and cis-[{2,6-(Me2 NCH2)2C6H3SnCl}2PdCl2]. DFT calculations provided insights into both the bonding situation of the compounds and the energy difference between the cis and trans isomers. The latter is influenced by the donor strength of the pincer-type ligands. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Syntheses, spectral characterization, X-ray studies and in vitro cytotoxic activities of triorganotin(IV) derivatives of p-substituted N-methylbenzylaminedithiocarbamates

NASA Astrophysics Data System (ADS)

Khan, Naqeebullah; Farina, Yang; Mun, Lo Kong; Rajab, Nor Fadilah; Awang, Normah

2014-11-01

Two new organotin(IV) complexes of the type R3SnL, where (L = p-bromo-N-methylbenzylaminedithiocarbamate and p-fluoro-N-methylbenzylaminedithiocarbamate, and R = phenyl) have been synthesized in 1:1 molar ratio with good yields and isolated as crystalline solids. The newly synthesized compounds gave fairly sharp melting points indicating that the compounds were pure. A systematic investigation of the derivatives were carried out both in solid and in solution and were suitably characterized by elemental analysis, FT-IR, 1H, 13C, 119Sn NMR spectroscopies. The dithiocarbamate ligands chelated to the tin metal monodentately using only one sulfur atom showing a pair of bands due to ν(Cdbnd S) below 1000 cm-1. This phenomenon was supported by the occurrence of new medium to weak absorptions in the region 411-545, in the spectra of complexes, assigned to ν(Snsbnd S) and ν(Snsbnd C). The crystal structures of the two triorganotin(IV) complexes have been determined by X-ray crystallography. Both the complexes crystallized in the monoclinic, P2(1)/n space group. The spectral investigations and single crystal X-ray diffraction data illustrate that the two dithiocarbamato ligands in the triphenyltin(IV) derivatives 1 and 2 are monodentate and the geometry at tin is best described as a distorted tetrahedron. The in vitro antiproliferative tests of these two derivatives on three human cell lines, leukemic lymphoblastoma Jurkat cells, lymphoblastoma K-562 cells, hepatoblastoma HepG2 cells and one mouse fibroblast cells L929 show dose-dependent decrease of cell proliferation in all cell lines.

N terminus of Swr1 binds to histone H2AZ and provides a platform for subunit assembly in the chromatin remodeling complex.

PubMed

Wu, Wei-Hua; Wu, Chwen-Huey; Ladurner, Andreas; Mizuguchi, Gaku; Wei, Debbie; Xiao, Hua; Luk, Ed; Ranjan, Anand; Wu, Carl

2009-03-06

Variant histone H2AZ-containing nucleosomes are involved in the regulation of gene expression. In Saccharomyces cerevisiae, chromatin deposition of histone H2AZ is mediated by the fourteen-subunit SWR1 complex, which catalyzes ATP-dependent exchange of nucleosomal histone H2A for H2AZ. Previous work defined the role of seven SWR1 subunits (Swr1 ATPase, Swc2, Swc3, Arp6, Swc5, Yaf9, and Swc6) in maintaining complex integrity and H2AZ histone replacement activity. Here we examined the function of three additional SWR1 subunits, bromodomain containing Bdf1, actin-related protein Arp4 and Swc7, by analyzing affinity-purified mutant SWR1 complexes. We observed that depletion of Arp4 (arp4-td) substantially impaired the association of Bdf1, Yaf9, and Swc4. In contrast, loss of either Bdf1 or Swc7 had minimal effects on overall complex integrity. Furthermore, the basic H2AZ histone replacement activity of SWR1 in vitro required Arp4, but not Bdf1 or Swc7. Thus, three out of fourteen SWR1 subunits, Bdf1, Swc7, and previously noted Swc3, appear to have roles auxiliary to the basic histone replacement activity. The N-terminal region of the Swr1 ATPase subunit is necessary and sufficient to direct association of Bdf1 and Swc7, as well as Arp4, Act1, Yaf9 and Swc4. This same region contains an additional H2AZ-H2B specific binding site, distinct from the previously identified Swc2 subunit. These findings suggest that one SWR1 enzyme might be capable of binding two H2AZ-H2B dimers, and provide further insight on the hierarchy and interdependency of molecular interactions within the SWR1 complex.

Surface oxidation of tin chalcogenide nanocrystals revealed by 119Sn-Mössbauer spectroscopy.

PubMed

de Kergommeaux, Antoine; Faure-Vincent, Jérôme; Pron, Adam; de Bettignies, Rémi; Malaman, Bernard; Reiss, Peter

2012-07-18

Narrow band gap tin(II) chalcogenide (SnS, SnSe, SnTe) nanocrystals are of high interest for optoelectronic applications such as thin film solar cells or photodetectors. However, charge transfer and charge transport processes strongly depend on nanocrystals' surface quality. Using (119)Sn-Mössbauer spectroscopy, which is the most sensitive tool for probing the Sn oxidation state, we show that SnS nanocrystals exhibit a Sn((IV))/Sn((II)) ratio of around 20:80 before and 40:60 after five minutes exposure to air. Regardless of the tin or sulfur precursors used, similar results are obtained using six different synthesis protocols. The Sn((IV)) content before air exposure arises from surface related SnS(2) and Sn(2)S(3) species as well as from surface Sn atoms bound to oleic acid ligands. The increase of the Sn((IV)) content upon air exposure results from surface oxidation. Full oxidation of the SnS nanocrystals without size change is achieved by annealing at 500 °C in air. With the goal to prevent surface oxidation, SnS nanocrystals are capped with a cadmium-phosphonate complex. A broad photoluminescence signal centered at 600 nm indicates successful capping, which however does not reduce the air sensitivity. Finally we demonstrate that SnSe nanocrystals exhibit a very similar behavior with a Sn((IV))/Sn((II)) ratio of 43:57 after air exposure. In the case of SnTe nanocrystals, the ratio of 55:45 is evidence of a more pronounced tendency for oxidation. These results demonstrate that prior to their use in optoelectronics further surface engineering of tin chalcogenide nanocrystals is required, which otherwise have to be stored and processed under inert atmosphere.

Effect of Rb2O and Cs2O on Inclusion Removal in 321 Stainless Steels Using Novel Basic Tundish Fluxes

NASA Astrophysics Data System (ADS)

Choi, Kyunsuk; Kang, Youngjo; Sohn, Il

2016-06-01

Inclusion removal and modification of the 321 stainless steel using Rb2O- and Cs2O-containing novel basic tundish flux has been investigated. The average inclusion diameter was significantly lowered after reaction of the liquid metal with the flux after 45 minutes in an induction furnace set at 1823 K (1550 °C) under an Ar atmosphere. The number of inclusions was also decreased with increased reaction time and the majority of the inherent TiN inclusions were removed after reaction with the proposed novel basic tundish flux. Spinel inclusions were also observed after the reaction, which was due to the reaction of the MgO crucible and the CaO-Al2O3-SiO2-MgO-` x'wt pct R2O flux system at fixed CaO/(Al2O3 + SiO2) of 1.45. The Rb2O and Cs2O seemed to have allowed significant removal of the TiN inclusions due to its ion compensation effect and the supplement of free oxygen ions, while increasing the viscosity of the slag to retain the absorbed inclusions.

Recent developments in the formation and structure of tin-iron oxides by laser pyrolysis

NASA Astrophysics Data System (ADS)

Alexandrescu, R.; Morjan, I.; Dumitrache, F.; Birjega, R.; Fleaca, C.; Soare, I.; Gavrila, L.; Luculescu, C.; Prodan, G.; Kuncser, V.; Filoti, G.

2011-04-01

Complex oxides demonstrate specific electric and magnetic properties which make them suitable for a wide variety of applications, including dilute magnetic semiconductors for spin electronics. A tin-iron oxide Sn 1- xFe xO 2 nanoparticulate material has been successfully synthesized by using the laser pyrolysis of tetramethyl tin-iron pentacarbonyl-air mixtures. Fe doping of SnO 2 nanoparticles has been varied systematically in the 3-10 at% range. As determined by EDAX, the Fe/Sn ratio (in at%) in powders varied between 0.14 and 0.64. XRD studies of Sn 1- xFe xO 2 nanoscale powders, revealed only structurally modified SnO 2 due to the incorporation of Fe into the lattice mainly by substitutional changes. The substitution of Fe 3+ in the Sn 4+ positions (Fe 3+ has smaller ionic radius as compared to the ionic radius of 0.69 Å for Sn 4+) with the formation of a mixed oxide Sn 1- xFe xO 2 is suggested. A lattice contraction consistent with the determined Fe/Sn atomic ratios was observed. The nanoparticle size decreases with the Fe doping (about 7 nm for the highest Fe content). Temperature dependent 57Fe Mössbauer spectroscopy data point to the additional presence of defected Fe 3+-based oxide nanoclusters with blocking temperatures below 60 K. A new Fe phase presenting magnetic order at substantially higher temperatures was evidenced and assigned to a new type of magnetism relating to the dispersed Fe ions into the SnO 2 matrix.

Synthesis of antimony-doped tin oxide (ATO) nanoparticles by the nitrate-citrate combustion method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Jianrong; Gao Lian

2004-12-02

Antimony-doped tin oxide (ATO) nanoparticles having rutile structure have been synthesized by the combustion method using citric acid (CA) as fuel and nitrate as an oxidant, the metal sources were granulated tin and Sb{sub 2}O{sub 3}. The influence of citric acid (fuel) to metal ratio on the average crystallite size, specific surface area and morphology of the nanoparticles has been investigated. X-ray diffraction showed the tin ions were reduced to elemental tin during combustion reaction. The average ATO crystallite size increased with the increase of citric acid (fuel). Powder morphology and the comparison of crystallite size and grain size showsmore » that the degree of agglomeration of the powder decreased with an increase of the ratio. The highest specific surface area was 37.5 m{sup 2}/g when the citric acid to tin ratio was about 6.« less

Access to Formally Ni(I) States in a Heterobimetallic NiZn System

PubMed Central

Uyeda, Christopher

2014-01-01

Heterobimetallic NiZn complexes featuring metal centers in distinct coordination environments have been synthesized using diimine-dioxime ligands as binucleating scaffolds. A tetramethylfuran-containing ligand derivative enables a stable one-electron-reduced S = 1/2 species to be accessed using Cp2Co as a chemical reductant. The resulting pseudo-square planar complex exhibits spectroscopic and crystallographic characteristics of a ligand-centered radical bound to a Ni(II) center. Upon coordination of a π-acidic ligand such as PPh3, however, a five-coordinate Ni(I) metalloradical is formed. The electronic structures of these reduced species provide insight into the subtle effects of ligand structure on the potential and reversibility of the NiII/I couple for complexes of redox-active tetraazamacrocycles. PMID:25614786

Studies on the bioavailability of zinc in humans: intestinal interaction of tin and zinc.

PubMed

Solomons, N W; Marchini, J S; Duarte-Favaro, R M; Vannuchi, H; Dutra de Oliveira, J E

1983-04-01

Mineral/mineral interactions at the intestinal level are important in animal nutrition and toxicology, but only limited understanding of their extent or importance in humans has been developed. An inhibitory interaction of dietary tin on zinc retention has been recently described from human metabolic studies. We have explored the tin/zinc interaction using the change-in-plasma-zinc-concentration method with a standard dosage of 12.5 mg of zinc as zinc sulfate in 100 ml of Coca-Cola. Sn/Zn ratios of 2:1, 4:1, and 8:1, constituted by addition of 25, 50, and 100 mg of tin as stannous chloride, had no significant overall effect on zinc uptake. The 100-mg dose of tin produced noxious gastrointestinal symptoms. Addition of iron as ferrous sulfate to form ratios of Sn/Fe/Zn of 1:1:1 and 2:2:1 with the standard zinc solution and the appropriate doses of tin produced a reduction of zinc absorption not dissimilar from that seen previously with zinc and iron alone, and addition of picolinic acid did not influence the uptake of zinc from the solution with the 2:2:1 Sn/Fe/Zn ratio.

Organotin-Induced Hemolysis, Shape Transformation and Intramembranous Aggregates in Human Erythrocytes

DTIC Science & Technology

1987-01-01

tributyltin , triethyltin, tripropyltin. 3. Abbreviations: DBT, dibutylin dichloride; MBT, butyltinchloride dihydroxide; SnCl2, stannous chloride; TBT , tri...compounds induce membrane lysis at low concentrations (Byington et al., 1974). Tri-n-butvltin ( TBT ) is a very effective hemolytic agent, causing membrane...based on numbers of butyl chains or numbers of carbon atoms in alkyl chains. TBT has been shown to produce 60-70 nm diameter, tin-containing

Tin, Bismuth, and Tin–Bismuth Alloy Electrodeposition from Chlorometalate Salts in Deep Eutectic Solvents

PubMed Central

Vieira, Luciana; Burt, Jennifer; Richardson, Peter W.; Schloffer, Daniel; Fuchs, David; Moser, Alwin; Bartlett, Philip N.; Reid, Gillian

2017-01-01

Abstract The electrodeposition of tin, bismuth, and tin–bismuth alloys from SnII and BiIII chlorometalate salts in the choline chloride/ethylene glycol (1:2 molar ratio) deep eutectic solvent was studied on glassy carbon and gold by cyclic voltammetry, rotating disc voltammetry, and chronoamperometry. The SnII‐containing electrolyte showed one voltammetric redox process corresponding to SnII/Sn0. The diffusion coefficient of [SnCl3]−, detected as the dominating species by Raman spectroscopy, was determined from Levich and Cottrell analyses. The BiIII‐containing electrolyte showed two voltammetric reduction processes, both attributed to BiIII/Bi0. Dimensionless current/time transients revealed that the electrodeposition of both Sn and Bi on glassy carbon proceeded by 3D‐progressive nucleation at a low overpotential and changed to instantaneous at higher overpotentials. The nucleation rate of Bi on glassy carbon was considerably smaller than that of Sn. Elemental Sn and Bi were electrodeposited on Au‐coated glass slides from their respective salt solutions, as were Sn–Bi alloys from a 2:1 SnII/BiIII solution. The biphasic Sn–Bi alloys changed from a Bi‐rich composition to a Sn‐rich composition by making the deposition potential more negative. PMID:28638772

Shaping bronze by heat and hammer: An experimental reproduction of Minoan Copper alloy forming techniques.

NASA Astrophysics Data System (ADS)

Nerantzis, Nerantzis

The compositions of copper-base tools, weapons, ornaments and ceremonial metalwork from numerous Late Bronze Age Aegean sites reveal a pattern of specific alloy combinations for the fabrication of certain classes of objects. Thus the majority of weapons and tools were made of high tin bronze whereas bronze statuettes, tripods and cauldrons contain small amounts of lead and in some cases tin is present in low amounts. Such diversity reflects the direct relationship between the compositions of prehistoric bronze objects and the art of their fabrication, because both the alloy additions and the impurities exert a pronounced effect on the forming capacity of alloys. In order to understand the correlation between composition and formability of Minoan bronzes, replica compositions with varying tin and lead contents were experimentally reproduced and their forming capacities were tested. Deformation and heat treatment of five tin and two leaded tin bronze alloys was attempted in order to replicate the forming stages for the shaping of cutting tools and bronze sheet for vessels and cauldrons. The amount of cold-working and annealing intervals, required to test the effects of workability on alloy properties, has been reflected as hardness values and transformations of the structural characteristics for each sample. It has been shown through the course of the experiment that high tin bronzes could be formed by frequent, short annealing stages at 600˚C and that it is possible to work-harden leaded bronze as long as time and temperatures are closely monitored.

Synthesis, characterization, biological evaluation and docking studies of macrocyclic binuclear manganese(II) complexes containing 3,5-dinitrobenzoyl pendant arms

NASA Astrophysics Data System (ADS)

Arthi, P.; Shobana, S.; Srinivasan, P.; Mitu, L.; Kalilur Rahiman, A.

2015-05-01

A series of bis(phenoxo) bridged binuclear manganese(II) complexes of the type [Mn2L1-3](ClO4)2 (1-3) containing 3,5-dinitrobenzoyl pendant-arms have been synthesized by cyclocondensation of 2,6-diformyl-4-R-phenols (where R = sbnd CH3, sbnd C(CH3)3 or sbnd Br) with 2,2‧-3,5-dinitrobenzoyliminodi(ethylamine) trihydrochloride in the presence of manganese(II) perchlorate. The IR spectra of complexes indicate the presence of uncoordinated perchlorate anions. The UV-Vis spectra of complexes suggest the distorted octahedral geometry around manganese(II) nuclei. The EPR spectra of Mn(II) complexes show a broad signal with g value 2.03-2.04, which is characteristic for octahedral high spin Mn2+ complex. The observed room temperature magnetic moment values of the Mn(II) complexes (5.60-5.62 B.M.) are less than the normal value (5.92 B.M.), indicating weak antiferromagnetic coupling interaction between the two metal ions. Electrochemical studies of the complexes show two distinct quasi-reversible one electron transfer processes in the cathodic (E1pc = -0.73 to -0.76 V, E2pc = -1.30 to -1.36 V), and anodic (E1pa = 1.02-1.11 V, E2pa = 1.32-1.79 V) potential regions. Antibacterial efficacy of complexes have been screened against four Gram (-ve) and two Gram (+ve) bacterial strains. The DNA interaction studies suggest that these complexes bind with CT-DNA by intercalation, giving the binding affinity in the order 1 > 2 > 3. All the complexes display significant cleavage activity against circular plasmid pBR322 DNA. Docking simulation was performed to insert complexes into the crystal structure of EGFR tyrosine kinase and B-DNA at active site to determine the probable binding mode.

76 FR 81441 - Proposed Significant New Use Rules on Certain Chemical Substances

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-28

... 5(a)(2) of the Toxic Substances Control Act (TSCA) for the chemical substances rutile, tin zinc, calcium-doped (CAS No. 389623-01- 2) and rutile, tin zinc, sodium-doped (CAS No. 389623-07-8) which were... two chemical substances are identified as rutile, tin zinc, calcium-doped (PMN P-06-36; CAS No. 389623...

XPS investigations of tribolayers formed on TiN and (Ti,Re)N coatings

NASA Astrophysics Data System (ADS)

Oktay, Serkan; Kahraman, Zafer; Urgen, Mustafa; Kazmanli, Kursat

2015-02-01

TiN and (Ti,Re)N coatings were deposited on high-speed-steel substrates by a hybrid coating system composed of cathodic arc PVD and magnetron sputtering techniques. In order to keep rhenium content low (8 ± 1.9 at.%) in the coating, magnetron sputtering technique was utilized to evaporate rhenium. The (Ti,Re)N coating consisted of TiN and ReNx (x > 1.33) phases. The hardness of TiN and (Ti,Re)N were 31 GPa and 29 GPa (± 2 GPa), respectively. Tribological behaviors of the samples were tested against Al2O3 balls at 21 °C (RT) and 150 °C (HT) by reciprocating wear technique. The tribolayers were analyzed by XPS technique. Friction coefficients of TiN were 0.56, 0.35 for 21 °C and 150 °C tests, respectively. Rhenium addition to TiN drastically dropped the friction coefficients to 0.22 and 0.17 for RT and HT samples. Rhenium addition also improved the wear resistance of the coating at both test temperatures. For TiN, main oxide component of the tribolayers was Ti2O3 for RT tests and TiO2 for HT tests. The oxide layer formed on (Ti,Re)N were the mixture of TiO2, Tisbnd Osbnd N, ReO2 and Re2O7 for both test temperatures. Re2O7 provided very low friction coefficient to (Ti,Re)N. The findings are consistent with the crystal chemistry approach.

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

21 CFR 178.2650 - Organotin stabilizers in vinyl chloride plastics.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) (1), (2), (3), (4), (5), (6), and (7) of this section. (1) Di(n-octyl)tin S,S′-bis(isooctylmercaptoacetate) is an octyltin chemical having 15.1 to 16.4 percent by weight of tin (Sn) and having 8.1 to 8.9 percent by weight of mercapto sulfur. It is made from di(n-octyl)tin dichloride or di(n-octyl)tin oxide...

A diverse virome in kidney transplant patients contains multiple viral subtypes with distinct polymorphisms

PubMed Central

Rani, Asha; Ranjan, Ravi; McGee, Halvor S.; Metwally, Ahmed; Hajjiri, Zahraa; Brennan, Daniel C.; Finn, Patricia W.; Perkins, David L.

2016-01-01

Recent studies have established that the human urine contains a complex microbiome, including a virome about which little is known. Following immunosuppression in kidney transplant patients, BK polyomavirus (BKV) has been shown to induce nephropathy (BKVN), decreasing graft survival. In this study we investigated the urine virome profile of BKV+ and BKV− kidney transplant recipients. Virus-like particles were stained to confirm the presence of VLP in the urine samples. Metagenomic DNA was purified, and the virome profile was analyzed using metagenomic shotgun sequencing. While the BK virus was predominant in the BKV+ group, it was also found in the BKV− group patients. Additional viruses were also detected in all patients, notably including JC virus (JCV) and Torque teno virus (TTV) and interestingly, we detected multiple subtypes of the BKV, JCV and TTV. Analysis of the BKV subtypes showed that nucleotide polymorphisms were detected in the VP1, VP2 and Large T Antigen proteins, suggesting potential functional effects for enhanced pathogenicity. Our results demonstrate a complex urinary virome in kidney transplant patients with multiple viruses with several distinct subtypes warranting further analysis of virus subtypes in immunosuppressed hosts. PMID:27633952

Utility of positron annihilation lifetime technique for the assessment of spectroscopic data of some charge-transfer complexes derived from N-(1-Naphthyl)ethylenediamine dihydrochloride

NASA Astrophysics Data System (ADS)

Refat, Moamen S.; Adam, Abdel Majid A.; Sharshar, T.; Saad, Hosam A.; Eldaroti, Hala H.

2014-03-01

In this work, structural, thermal, morphological, pharmacological screening and positron annihilation lifetime measurements were performed on the interactions between a N-(1-Naphthyl)ethylenediamine dihydrochloride (NEDA·2HCl) donor and three types of acceptors to characterize these CT complexes. The three types of acceptors include π-acceptors (quinol and picric acid), σ-acceptors (iodine) and vacant orbital acceptors (tin(IV) tetrachloride and zinc chloride). The positron annihilation lifetime parameters were found to be dependent on the structure, electronic configuration, the power of acceptors and molecular weight of the CT complexes. The positron annihilation lifetime spectroscopy can be used as a probe for the formation of charge-transfer (CT) complexes.

Effects of vanadium ion implantation on microstructure, mechanical and tribological properties of TiN coatings

NASA Astrophysics Data System (ADS)

Deng, Bin; Tao, Ye; Guo, Deliang

2012-09-01

TiN coatings were deposited on the substrates of cemented carbide (WC-TiC-Co) by Magnetic Filter Arc Ion Plating (MFAIP) and then implanted with vanadium through Metal Vacuum Vapor Arc (MEVVA) ion source with the doses of 1 × 1017 and 5 × 1017 ions/cm2 at 40 kV. The microstructures and chemical compositions of the V-implanted TiN coatings were investigated using Glancing Incidence X-ray Diffraction (GIXRD) and X-ray Photoelectron Spectroscopy (XPS), together with the mechanical and tribological properties of coatings were characterized using nano-indentation and ball-on-disk tribometer. It was found that the diffraction peaks of the V-implanted TiN coatings at the doses of 5 × 1017 ions/cm2 shifted to higher angles and became broader. The hardness and elastic modulus of TiN coatings increased after V ion implantation. The wear mechanism for both un-implanted and V-implanted TiN coatings against GCr15 steel ball was adhesive wear, and the V-implanted TiN coatings had a lower friction coefficient as well as a better wear resistance

Vps26B-retromer negatively regulates plasma membrane resensitization of PAR-2.

PubMed

Bugarcic, Andrea; Vetter, Irina; Chalmers, Silke; Kinna, Genevieve; Collins, Brett M; Teasdale, Rohan D

2015-11-01

Retromer is a trimeric complex composed of Vps26, Vps29, and Vps35 and has been shown to be involved in trafficking and sorting of transmembrane proteins within the endosome. The Vps26 paralog, Vps26B, defines a distinct retromer complex (Vps26B-retromer) in vivo and in vitro. Although endosomally associated, Vps26B-retromer does not bind the established retromer transmembrane cargo protein, cation-independent mannose 6-phosphate receptor (CI-M6PR), indicating it has a distinct role to retromer containing the Vps26A paralog. In the present study we use the previously established Vps26B-expressing HEK293 cell model to address the role of Vps26B-retromer in trafficking of the protease activated G-protein coupled receptor PAR-2 to the plasma membrane. In these cells there is no apparent defect in the initial activation of the receptor, as evidenced by release of intracellular calcium, ERK1/2 signaling and endocytosis of activated receptor PAR-2 into degradative organelles. However, we observe a significant delay in plasma membrane repopulation of the protease activated G protein-coupled receptor PAR-2 following stimulation, resulting in a defect in PAR-2 activation after resensitization. Here we propose that PAR-2 plasma membrane repopulation is regulated by Vps26B-retromer, describing a potential novel role for this complex. © 2015 International Federation for Cell Biology.

Origin of the mysterious Yin-Shang bronzes in China indicated by lead isotopes

PubMed Central

Sun, Wei-dong; Zhang, Li-peng; Guo, Jia; Li, Cong-ying; Jiang, Yu-hang; Zartman, Robert E.; Zhang, Zhao-feng

2016-01-01

Fine Yin-Shang bronzes containing lead with puzzlingly highly radiogenic isotopic compositions appeared suddenly in the alluvial plain of the Yellow River around 1400 BC. The Tongkuangyu copper deposit in central China is known to have lead isotopic compositions even more radiogenic and scattered than those of the Yin-Shang bronzes. Most of the Yin-Shang bronzes are tin-copper alloys with high lead contents. The low lead and tin concentrations, together with the less radiogenic lead isotopes of bronzes in an ancient smelting site nearby, however, exclude Tongkuangyu as the sole supplier of the Yin-Shang bronzes. Interestingly, tin ingots/prills and bronzes found in Africa also have highly radiogenic lead isotopes, but it remains mysterious as to how such African bronzes may have been transported to China. Nevertheless, these African bronzes are the only bronzes outside China so far reported that have lead isotopes similar to those of the Yin-Shang bronzes. All these radiogenic lead isotopes plot along ~2.0–2.5 Ga isochron lines, implying that deposits around Archean cratons are the most likely candidates for the sources. African cratons along the Nile and even micro-cratons in the Sahara desert may have similar lead signatures. These places were probably accessible by ancient civilizations, and thus are the most favorable suppliers of the bronzes. PMID:26988425

Nucleophilically assisted and cationic ring-opening polymerization of tin-bridged [1]ferrocenophanes.

PubMed

Baumgartner, Thomas; Jäkle, Frieder; Rulkens, Ron; Zech, Gernot; Lough, Alan J; Manners, Ian

2002-08-28

To obtain mechanistic insight, detailed studies of the intriguing "spontaneous" ambient temperature ring-opening polymerization (ROP) of tin-bridged [1]ferrocenophanes Fe(eta-C(5)H(4))(2)SnR(2) 3a (R = t-Bu) and 3b (R = Mes) in solution have been performed. The investigations explored the influence of non-nucleophilic additives such as radicals and radical traps, neutral and anionic nucleophiles, Lewis acids, protic species, and other cationic electrophiles. Significantly, two novel methodologies and mechanisms for the ROP of strained [1]ferrocenophanes are proposed based on this study. First, as the addition of amine nucleophiles such as pyridine was found to strongly accelerate the polymerization rate in solution, a new nucleophilicallyassisted ROP methodology was proposed. This operates at ambient temperature in solution even in the presence of chlorosilanes but, unlike the anionic polymerization of ferrocenophanes, does not involve cyclopentadienyl anions. Second, the addition of small quantities of the electrophilic species H(+) and Bu(3)Sn(+) was found to lead to a cationic ROP process. These studies suggest that the "spontaneous" ROP of tin-bridged [1]ferrocenophanes may be a consequence of the presence of spurious, trace quantities of Lewis basic or acidic impurities. The new ROP mechanisms reported are likely to be of general significance for the ROP of other metallocenophanes (e.g., for thermal ROP in the melt) and for other metallacycles containing group 14 elements.

High-pressure synthesis and characterization of incompressible titanium pernitride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhadram, Venkata S.; Kim, Duck Young; Strobel, Timothy A.

A new transition-metal pernitride, TiN 2, was uncovered from the chemical reaction of TiN with N 2 at 73GPa in a laser-heated diamond anvil cell (DAC). The crystal structure of this compound exhibits tetragonal I 4/ mcm symmetry and consists of single-bonded nitrogen dimers (N–N dumbbells) embedded in the metal lattice as shown by our ab initio calculations and verified by in situ synchrotron x-ray diffraction measurements. The pressure-volume equation of state determined from the experimental data reveals that TiN 2 is incompressible with bulk modulus in the range of 360-385 GPa which is close to that of cubic boronmore » nitride (382 GPa). Here, the origin of high bulk modulus of TiN 2 (which is metallic) is rooted in the nearly filled anti-bonding states of the pernitride units. TiN 2 is fully recoverable to ambient conditions and represents the lowest-density transition metal pernitride synthesized to date.« less

A secreted Ustilago maydis effector promotes virulence by targeting anthocyanin biosynthesis in maize

PubMed Central

Tanaka, Shigeyuki; Brefort, Thomas; Neidig, Nina; Djamei, Armin; Kahnt, Jörg; Vermerris, Wilfred; Koenig, Stefanie; Feussner, Kirstin; Feussner, Ivo; Kahmann, Regine

2014-01-01

The biotrophic fungus Ustilago maydis causes smut disease in maize with characteristic tumor formation and anthocyanin induction. Here, we show that anthocyanin biosynthesis is induced by the virulence promoting secreted effector protein Tin2. Tin2 protein functions inside plant cells where it interacts with maize protein kinase ZmTTK1. Tin2 masks a ubiquitin–proteasome degradation motif in ZmTTK1, thus stabilizing the active kinase. Active ZmTTK1 controls activation of genes in the anthocyanin biosynthesis pathway. Without Tin2, enhanced lignin biosynthesis is observed in infected tissue and vascular bundles show strong lignification. This is presumably limiting access of fungal hyphae to nutrients needed for massive proliferation. Consistent with this assertion, we observe that maize brown midrib mutants affected in lignin biosynthesis are hypersensitive to U. maydis infection. We speculate that Tin2 rewires metabolites into the anthocyanin pathway to lower their availability for other defense responses. DOI: http://dx.doi.org/10.7554/eLife.01355.001 PMID:24473076

High-pressure synthesis and characterization of incompressible titanium pernitride

DOE PAGES

Bhadram, Venkata S.; Kim, Duck Young; Strobel, Timothy A.

2016-03-07

A new transition-metal pernitride, TiN 2, was uncovered from the chemical reaction of TiN with N 2 at 73GPa in a laser-heated diamond anvil cell (DAC). The crystal structure of this compound exhibits tetragonal I 4/ mcm symmetry and consists of single-bonded nitrogen dimers (N–N dumbbells) embedded in the metal lattice as shown by our ab initio calculations and verified by in situ synchrotron x-ray diffraction measurements. The pressure-volume equation of state determined from the experimental data reveals that TiN 2 is incompressible with bulk modulus in the range of 360-385 GPa which is close to that of cubic boronmore » nitride (382 GPa). Here, the origin of high bulk modulus of TiN 2 (which is metallic) is rooted in the nearly filled anti-bonding states of the pernitride units. TiN 2 is fully recoverable to ambient conditions and represents the lowest-density transition metal pernitride synthesized to date.« less

THz conductivities of indium-tin-oxide nanowhiskers as a graded-refractive-index structure.

PubMed

Yang, Chan-Shan; Chang, Chia-Hua; Lin, Mao-Hsiang; Yu, Peichen; Wada, Osamu; Pan, Ci-Ling

2012-07-02

Indium-tin-oxide (ITO) nanowhiskers with attractive electrical and anti-reflection properties were prepared by the glancing-angle electron-beam evaporation technique. Structural and crystalline properties of such nanostructures were examined by scanning transmission electron microscopy and X-ray diffraction. Their frequency-dependent complex conductivities, refractive indices and absorption coefficients have been characterized with terahertz time-domain spectroscopy (THz-TDS), in which the nanowhiskers were considered as a graded-refractive-index (GRIN) structure instead of the usual thin film model. The electrical properties of ITO GRIN structures are analyzed and fitted well with Drude-Smith model in the 0.2~2.0 THz band. Our results indicate that the ITO nanowhiskers and its bottom layer atop the substrate exhibit longer carrier scattering times than ITO thin films. This signifies that ITO nanowhiskers have an excellent crystallinity with large grain size, consistent with X-ray data. Besides, we show a strong backscattering effect and fully carrier localization in the ITO nanowhiskers.

Phase diagram of electron systems near the superconductor-insulator transition.

PubMed

Pokrovsky, V L; Falco, G M; Nattermann, T

2010-12-31

The zero temperature phase diagram of Cooper pairs exposed to disorder and a magnetic field is determined theoretically from a variational approach. Four distinct phases are found: a Bose and a Fermi insulating, a metallic, and a superconducting phase, respectively. The results explain the giant negative magnetoresistance found experimentally in In-O, TiN, Be and high-T(c) materials.

Bronze Alloy Development for Zinc Vapor Capture

DOE PAGES

Korinko, Paul S.

2017-04-24

After gamma-emitting 65Zinc was detected in a vacuum pumping system contained in a tritium glovebox, a series of experiments were undertaken to develop a method and material to trap zinc vapors in an area that is more suitable for preventing dose to workers. In this study, bronze alloys with 0–30% tin were prepared using a powder metallurgical process and exposed to three levels of zinc vapors. Furthermore, all of the alloys demonstrated acceptable zinc gettering capacity; however, low tin content bronzes are considered for further testing.

Characterization study of polycrystalline tin oxide surfaces before and after reduction in CO

NASA Technical Reports Server (NTRS)

Drawdy, Jean E.; Hoflund, Gar B.; Davidson, Mark R.; Schryer, David R.

1990-01-01

Polycrystalline tin oxide surfaces have been examined before and after reduction in 40 Torr of CO at 100 and 175 C using Auger electron spectroscopy (AES), electron spectroscopy for chemical analysis (ESCA), ion scattering spectroscopy (ISS) and electron stimulated desorption (ESD). The changes in the surface composition and chemical states of the surface species generally are subtle for the reductive conditions used. However, significant changes do occur with regard to the amounts and the chemical forms of the hydrogen-containing species remaining after both the 100 and 175 C reductions.

Effects of interfacial layer on characteristics of TiN/ZrO2 structures.

PubMed

Kim, Younsoo; Kang, Sang Yeol; Choi, Jae Hyoung; Lim, Jae Soon; Park, Min Young; Chung, Suk-Jin; Chung, Jaegwan; Lee, Hyung Ik; Kim, Ki Hong; Kyoung, Yong Koo; Heo, Sung; Yoo, Cha Young; Kang, Ho-Kyu

2011-09-01

To minimize the formation of unwanted interfacial layers, thin interfacial layer (ZrCN layer) was deposited between TiN bottom electrode and ZrO2 dielectric in TiN/ZrO2/TiN capacitor. Carbon and nitrogen were also involved in the layer because ZrCN layer was thermally deposited using TEMAZ without any reactant. Electrical characteristics of TiN/ZrO2/TiN capacitor were improved by insertion of ZrCN layer. The oxidation of TiN bottom electrode was largely inhibited at TiN/ZrCN/ZrO2 structure compared to TiN/ZrO2 structure. While the sheet resistance of TiN/ZrCN/ZrO2 structure was constantly sustained with increasing ZrO2 thickness, the large increase of sheet resistance was observed in TiN/ZrO2 structure after 6 nm ZrO2 deposition. When ZrO2 films were deposited on ZrCN layer, the deposition rate of ZrO2 also increased. It is believed that ZrCN layer acted both as a protection layer of TiN oxidation and a seed layer of ZrO2 growth.

Battery plate containing filler with conductive coating

NASA Technical Reports Server (NTRS)

Rowlette, John J. (Inventor)

1986-01-01

The plate (10) comprises a matrix or binder resin phase (12) in which is dispersed particulate, conductive tin oxide such as tin oxide coated glass fibers (14). A monopolar plate (11) is prepared by coating a layer (18) of electrolytically active material onto a surface of the plate (10). Tin oxide is prevented from reduction by coating a surface of the plate (10) with a conductive, impervious layer resistant to reduction such as a thin film (22) of lead adhered to the plate with a layer (21) of conductive adhesive. The plate (10) can be formed by casting a molten dispersion from mixer (36) onto a sheet (30) of lead foil or by passing an assembly of a sheet (41) of resin, a sheet (43) of fiberglass and a sheet (45) of lead between the nip of heated rollers (48, 50).

Battery plate containing filler with conductive coating

NASA Technical Reports Server (NTRS)

Rowlette, John J. (Inventor)

1985-01-01

The plate (10) comprises a matrix or binder resin phase (12) in which is dispersed particulate, conductive tin oxide such as tin oxide coated glass fibers (14). A monopolar plate (11) is prepared by coating a layer (18) of electrolytically active material onto a surface of the plate (10). Tin oxide is prevented from reduction by coating a surface of the plate (10) with a conductive, impervious layer resistant to reduction such as a thin film (22) of lead adhered to the plate with a layer (21) of conductive adhesive. The plate (10) can be formed by casting a molten dispersion from mixer (36) onto a sheet (30) of lead foil or by passing an assembly of a sheet (41) of resin, a sheet (43) of fiberglass and a sheet (45) of lead between the nip of heated rollers (48, 50).

Sequential protein association with nascent 60S ribosomal particles.

PubMed

Saveanu, Cosmin; Namane, Abdelkader; Gleizes, Pierre-Emmanuel; Lebreton, Alice; Rousselle, Jean-Claude; Noaillac-Depeyre, Jacqueline; Gas, Nicole; Jacquier, Alain; Fromont-Racine, Micheline

2003-07-01

Ribosome biogenesis in eukaryotes depends on the coordinated action of ribosomal and nonribosomal proteins that guide the assembly of preribosomal particles. These intermediate particles follow a maturation pathway in which important changes in their protein composition occur. The mechanisms involved in the coordinated assembly of the ribosomal particles are poorly understood. We show here that the association of preribosomal factors with pre-60S complexes depends on the presence of earlier factors, a phenomenon essential for ribosome biogenesis. The analysis of the composition of purified preribosomal complexes blocked in maturation at specific steps allowed us to propose a model of sequential protein association with, and dissociation from, early pre-60S complexes for several preribosomal factors such as Mak11, Ssf1, Rlp24, Nog1, and Nog2. The presence of either Ssf1 or Nog2 in complexes that contain the 27SB pre-rRNA defines novel, distinct pre-60S particles that contain the same pre-rRNA intermediates and that differ only by the presence or absence of specific proteins. Physical and functional interactions between Rlp24 and Nog1 revealed that the assembly steps are, at least in part, mediated by direct protein-protein interactions.

Molten Salt Electrolytically Produced Carbon/Tin Nanomaterial as the Anode in a Lithium Ion Battery

NASA Astrophysics Data System (ADS)

Das Gupta, Rajshekar; Schwandt, Carsten; Fray, Derek J.

2017-03-01

A carbon/tin nanomaterial, consisting of predominantly Sn-filled carbon nanotubes and nanoparticles, is prepared by molten salt electrochemistry, using electrodes of graphite and an electrolyte of LiCl salt containing a small admixture of SnCl2. The C/Sn hybrid material generated is incorporated into the active anode material of a lithium ion battery and tested with regard to storage capacity and cycling behavior. The results demonstrate that the C/Sn material has favorable properties, in terms of energy density and in particular long-term stability, that exceed those of the individual components alone. The initial irreversible capacity of the material is somewhat larger than that of conventional battery graphite which is due to its unique nanostructure. Overall the results would indicate the suitability of this material for use in the anodes of lithium ion batteries with high rate capability.

Quantitative Interpretation of Multifrequency Multimode EPR Spectra of Metal Containing Proteins, Enzymes, and Biomimetic Complexes.

PubMed

Petasis, Doros T; Hendrich, Michael P

2015-01-01

Electron paramagnetic resonance (EPR) spectroscopy has long been a primary method for characterization of paramagnetic centers in materials and biological complexes. Transition metals in biological complexes have valence d-orbitals that largely define the chemistry of the metal centers. EPR spectra are distinctive for metal type, oxidation state, protein environment, substrates, and inhibitors. The study of many metal centers in proteins, enzymes, and biomimetic complexes has led to the development of a systematic methodology for quantitative interpretation of EPR spectra from a wide array of metal containing complexes. The methodology is now contained in the computer program SpinCount. SpinCount allows simulation of EPR spectra from any sample containing multiple species composed of one or two metals in any spin state. The simulations are quantitative, thus allowing determination of all species concentrations in a sample directly from spectra. This chapter will focus on applications to transition metals in biological systems using EPR spectra from multiple microwave frequencies and modes. © 2015 Elsevier Inc. All rights reserved.

(abstract) A Brief, Selective Review of Thermal Cycling Fatigue in Eutectic Tin-Lead Solder

NASA Technical Reports Server (NTRS)

Winslow, J. W.; Silveira, C. de

1993-01-01

This paper reviews selected parts of the current literature relevant to thermo-mechanical fatigue mechanisms in eutectic tin-lead solder, and suggests a general outline to account for some observed failures. The field is found to be complex. One recent experimental study finds some failure modes to be sensitive to joint geometry. Attempts to extrapolate from test environments to service environments have had only limited success. Much work remains to be done before fatigue failures in this material can be considered as under practical control.

Nanostructured metal oxide-based materials as advanced anodes for lithium-ion batteries.

PubMed

Wu, Hao Bin; Chen, Jun Song; Hng, Huey Hoon; Lou, Xiong Wen David

2012-04-21

The search for new electrode materials for lithium-ion batteries (LIBs) has been an important way to satisfy the ever-growing demands for better performance with higher energy/power densities, improved safety and longer cycle life. Nanostructured metal oxides exhibit good electrochemical properties, and they are regarded as promising anode materials for high-performance LIBs. In this feature article, we will focus on three different categories of metal oxides with distinct lithium storage mechanisms: tin dioxide (SnO(2)), which utilizes alloying/dealloying processes to reversibly store/release lithium ions during charge/discharge; titanium dioxide (TiO(2)), where lithium ions are inserted/deinserted into/out of the TiO(2) crystal framework; and transition metal oxides including iron oxide and cobalt oxide, which react with lithium ions via an unusual conversion reaction. For all three systems, we will emphasize that creating nanomaterials with unique structures could effectively improve the lithium storage properties of these metal oxides. We will also highlight that the lithium storage capability can be further enhanced through designing advanced nanocomposite materials containing metal oxides and other carbonaceous supports. By providing such a rather systematic survey, we aim to stress the importance of proper nanostructuring and advanced compositing that would result in improved physicochemical properties of metal oxides, thus making them promising negative electrodes for next-generation LIBs.

Determination of total tin in silicate rocks by graphite furnace atomic absorption spectrometry

USGS Publications Warehouse

Elsheimer, H.N.; Fries, T.L.

1990-01-01

A method is described for the determination of total tin in silicate rocks utilizing a graphite furnace atomic absorption spectrometer with a stabilized-temperature platform furnace and Zeeman-effect background correction. The sample is decomposed by lithium metaborate fusion (3 + 1) in graphite crucibles with the melt being dissolved in 7.5% hydrochloric acid. Tin extractions (4 + 1 or 8 + 1) are executed on portions of the acid solutions using a 4% solution of tricotylphosphine oxide in methyl isobutyl ketone (MIBK). Ascorbic acid is added as a reducing agent prior to extraction. A solution of diammonium hydrogenphosphate and magnesium nitrate is used as a matrix modifier in the graphite furnace determination. The limit of detection is > 10 pg, equivalent to > 1 ??g l-1 of tin in the MIBK solution or 0.2-0.3 ??g g-61 in the rock. The concentration range is linear between 2.5 and 500 ??g l-1 tin in solution. The precision, measured as relative standard deviation, is < 20% at the 2.5 ??g l-1 level and < 7% at the 10-30 ??g l-1 level of tin. Excellent agreement with recommended literature values was found when the method was applied to the international silicate rock standards BCR-1, PCC-1, GSP-1, AGV-1, STM-1, JGb-1 and Mica-Fe. Application was made to the determination of tin in geological core samples with total tin concentrations of the order of 1 ??g g-1 or less.

Crystal structure of the new A2SnTa6X18 (A = K, Rb, Cs; X = Cl, Br) cluster compounds

NASA Astrophysics Data System (ADS)

Lemoine, P.; Wilmet, M.; Malaman, B.; Paofai, S.; Dumait, N.; Cordier, S.

2018-01-01

The crystal structure of the new cluster compounds A2SnTa6X18 (with A = K, Rb, Cs, and X = Cl, Br) was determined by using single-crystal and powder X-ray diffraction, and 119Sn Mössbauer spectroscopy. Those compounds crystallize in the Cs2EuNb6Br18-type structure of space group R 3 ̅. This type of structure is built up on discrete edge-bridged [M6Xi12Xa6]4- cluster units arranged according to a pseudo face-centered cubic stacking, where the octahedral and tetrahedral vacancies are fully occupied by divalent tin cations and monovalent alkaline cations, respectively. The tin cations influence on the halogen matrix and the electronic effects on the cluster units in the Cs2EuNb6Br18-type structure are discussed by comparison with isotype compounds. From those analyses, the ionic radius of Sn2+ in coordination number VI is estimated to be 1.14(1) Å. Finally, K2SnTa6Br18 might be considered as a new example of compound containing a quite bare stannous ion (5 s2 configuration).

A TBP-containing multiprotein complex (TIF-IB) mediates transcription specificity of murine RNA polymerase I.

PubMed

Eberhard, D; Tora, L; Egly, J M; Grummt, I

1993-09-11

TIF-IB is a transcription factor which interacts with the mouse ribosomal gene promoter and nucleates the formation of an initiation complex containing RNA polymerase I (Pol I). We have purified this factor to near homogeneity and demonstrate that TIF-IB is a large complex (< 200 kDa) which contains several polypeptides. One of the subunits present in this protein complex is the TATA-binding protein (TBP) as revealed by copurification of TIF-IB activity and TBP over different chromatographic steps including immunoaffinity purification. In addition to TBP, three tightly associated proteins (TAFs-I) with apparent molecular weights of 95, 68, and 48 kDa are contained in this multimeric complex. This subunit composition is similar--but not identical--to the analogous human factor SL1. Depletion of TBP from TIF-IB-containing fractions by immunoprecipitation eliminates TIF-IB activity. Neither TBP alone nor fractions containing other TBP complexes are capable of substituting for TIF-IB activity. Therefore, TIF-IB is a unique complex with Pol I-specific TAFs distinct from other TBP-containing complexes. The identification of TBP as an integral part of the murine rDNA promoter-specific transcription initiation factor extends the previously noted similarity of transcriptional initiation by the three nuclear RNA polymerases and underscores the importance of TAFs in determining promoter specificity.

A TBP-containing multiprotein complex (TIF-IB) mediates transcription specificity of murine RNA polymerase I.

PubMed Central

Eberhard, D; Tora, L; Egly, J M; Grummt, I

1993-01-01

TIF-IB is a transcription factor which interacts with the mouse ribosomal gene promoter and nucleates the formation of an initiation complex containing RNA polymerase I (Pol I). We have purified this factor to near homogeneity and demonstrate that TIF-IB is a large complex (< 200 kDa) which contains several polypeptides. One of the subunits present in this protein complex is the TATA-binding protein (TBP) as revealed by copurification of TIF-IB activity and TBP over different chromatographic steps including immunoaffinity purification. In addition to TBP, three tightly associated proteins (TAFs-I) with apparent molecular weights of 95, 68, and 48 kDa are contained in this multimeric complex. This subunit composition is similar--but not identical--to the analogous human factor SL1. Depletion of TBP from TIF-IB-containing fractions by immunoprecipitation eliminates TIF-IB activity. Neither TBP alone nor fractions containing other TBP complexes are capable of substituting for TIF-IB activity. Therefore, TIF-IB is a unique complex with Pol I-specific TAFs distinct from other TBP-containing complexes. The identification of TBP as an integral part of the murine rDNA promoter-specific transcription initiation factor extends the previously noted similarity of transcriptional initiation by the three nuclear RNA polymerases and underscores the importance of TAFs in determining promoter specificity. Images PMID:8414971

In vivo biochemical analyses reveal distinct roles of β-importins and eEF1A in tRNA subcellular traffic.

PubMed

Huang, Hsiao-Yun; Hopper, Anita K

2015-04-01

Bidirectional tRNA movement between the nucleus and the cytoplasm serves multiple biological functions. To gain a biochemical understanding of the mechanisms for tRNA subcellular dynamics, we developed in vivo β-importin complex coimmunoprecipitation (co-IP) assays using budding yeast. Our studies provide the first in vivo biochemical evidence that two β-importin family members, Los1 (exportin-t) and Msn5 (exportin-5), serve overlapping but distinct roles in tRNA nuclear export. Los1 assembles complexes with RanGTP and tRNA. Both intron-containing pre-tRNAs and spliced tRNAs, regardless of whether they are aminoacylated, assemble into Los1-RanGTP complexes, documenting that Los1 participates in both primary nuclear export and re-export of tRNAs to the cytoplasm. In contrast, β-importin Msn5 preferentially assembles with RanGTP and spliced, aminoacylated tRNAs, documenting its role in tRNA nuclear re-export. Tef1/2 (the yeast form of translation elongation factor 1α [eEF1A]) aids the specificity of Msn5 for aminoacylated tRNAs to form a quaternary complex consisting of Msn5, RanGTP, aminoacylated tRNA, and Tef1/2. Assembly and/or stability of this quaternary complex requires Tef1/2, thereby facilitating efficient re-export of aminoacylated tRNAs to the cytoplasm. © 2015 Huang and Hopper; Published by Cold Spring Harbor Laboratory Press.

Paired Magmatic-Metallogenic Belts in Myanmar - an Andean Analogue?

NASA Astrophysics Data System (ADS)

Gardiner, Nicholas; Robb, Laurence; Searle, Michael; Morley, Christopher

2015-04-01

Myanmar (Burma) is richly endowed in precious and base metals, having one of the most diverse collections of natural resources in SE Asia. Its geological history is dominated by the staged closing of Tethys and the suturing of Gondwana-derived continental fragments onto the South China craton during the Mesozoic-Cenozoic. The country is located at a crucial geologic juncture where the main convergent Tethyan collision zone swings south around the Namche Barwa Eastern Himalayan syntaxis. However, despite recent work, the geological and geodynamic history of Myanmar remains enigmatic. Plate margin processes, magmatism, metasomatism and the genesis of mineral deposits are intricately linked, and there has long been recognized a relationship between the distribution of certain mineral deposit types, and the tectonic settings which favour their genesis. A better knowledge of the regional tectonic evolution of a potential exploration jurisdiction is therefore crucial to understanding its minerals prospectivity. This strong association between tectonics and mineralization can equally be applied in reverse. By mapping out the spatial, and temporal, distribution of presumed co-genetic mineral deposits, coupled with an understanding of their collective metallogenetic origin, a better appreciation of the tectonic evolution of a terrane may be elucidated. Identification and categorization of metallotects within a geodynamically-evolving terrane thus provides a complimentary tool to other methodologies (e.g. geochemical, geochronological, structural, geophysical, stratigraphical), for determining the tectonic history and inferred geodynamic setting of that terrane through time. Myanmar is one such study area where this approach can be undertaken. Here are found two near-parallel magmatic belts, which together contain a significant proportion of that country's mineral wealth of tin, tungsten, copper, gold and silver. Although only a few 100 km's apart, these belts exhibit a contrasting minerals endowment. The Mogok-Mandalay-Mergui (MMM) Belt hosts crustal-melt S-type granites with significant tin-tungsten mineralization, and contains the historically major tungsten deposit of Mawchi. The Wuntho-Popa Arc comprises I-type granites and granodiorites with porphyry-type copper-gold and epithermal gold mineralization, and includes the world-class Monywa copper mine. Recent U-Pb radiometric age dating has shown the potential for the two belts to be both active from the Late Cretaceous to Eocene. The spatial juxtaposition of these two sub-parallel belts, the implication of contemporary magmatism, and their distinct but consistent metallogenic endowment bears strong similarities to the metallogenic belts of the South American Cordillera. Here we investigate whether they together represent the magmatic and metallogenic expression of an Andean-type setting in Myanmar during the subduction of Neo-Tethys. In this analogue the Wuntho-Popa Arc represents a proximal I-type magmatic belt sited immediately above the eastwards-verging Neo-Tethys subduction zone. Exhibiting porphyry-type copper-gold and epithermal gold mineralization, this would therefore be the Myanmar equivalent of the Andean coastal copper belts. Conversely, the parallel MMM Belt, comprised of more distal crustal-melt S-type tin granites, would have an analogue in the Bolivian tin belt.

Renal tubular disease in the era of combination antiretroviral therapy.

PubMed

Hamzah, Lisa; Booth, John W; Jose, Sophie; McAdoo, Stephen P; Kumar, Emil A; O'Donnell, Patrick; Hilton, Rachel; Sabin, Caroline; Williams, Deborah I; Jones, Rachael; Post, Frank A

2015-09-10

To describe the spectrum of renal tubular disease (RTD) in HIV-positive patients and its association with exposure to antiretroviral therapy (ART). Review of 265 consecutive renal biopsies from HIV-positive patients attending eight clinics in the United Kingdom between 2000 and 2012. We described the clinical characteristics of patients with RTD and compared current/recent exposure (at the time of, or up to 3 months prior to the date of biopsy) to potentially nephrotoxic ART [tenofovir (TDF), atazanavir (ATV), indinavir (IDV) and lopinavir/ritonavir (LPV/r)]. We also analysed the incidence of RTD in the UK CHIC cohort. Kruskall-Wallis, analysis of variance and Fisher's exact tests were used to evaluate between-group differences. Of the 60 RTD cases, 54 (90%) were included in the analyses. RTD comprised of three distinct patterns: acute tubular injury (ATI, n = 22), tubulo-interstitial nephritis (TIN, n = 20) and interstitial fibrosis and tubular atrophy (IFTA, n = 12). Compared with TIN and IFTA, ATI cases were less likely to be of black ethnicity (10 vs. 42-55%; P = 0.006), more likely to be on ART (100 vs. 55-68%; P = 0.001), with HIV-RNA below 200 copies/ml (100 vs. 54-58%; P < 0.001), and more likely to have current/recent exposure to TDF (P < 0.001). We did not find evidence for an association between exposure to TDF, ATV/r or LPV/r and either TIN or IFTA. RTD was present in approximately 20% of renal biopsies and comprised three distinct injury patterns with considerable clinical overlap. ATI was associated with TDF exposure, although the overall incidence of biopsy-defined ATI was low.

Mechanical properties of PEO-coatings on the surface of magnesium alloy MA8 modified by TiN nanoparticles

NASA Astrophysics Data System (ADS)

Imshinetsky, Igor M.; Mashtalyar, Dmitriy V.; Sunebryukhov, Sergey L.; Gnedenkov, Sergey V.

2017-09-01

The methods to form protective coatings by the plasma electrolytic oxidation method (PEO) in the electrolytic system containing nanosized particles of titanium nitride has been develoted. Tribological and morfological studies of the composite coatings have been carried out. It has been established that the microhardness of the coating with nanoparticles concentration of 3 g/l increases by 2 folds, while the wear resistance - by 2.2 fold, as compared to respective values for the PEO-coating formed in the electrolyte without nanoparticles.

The Ruthenostannylene Complex [Cp*(IXy)H2 Ru-Sn-Trip]: Providing Access to Unusual Ru-Sn Bonded Stanna-imine, Stannene, and Ketenylstannyl Complexes.

PubMed

Liu, Hsueh-Ju; Ziegler, Micah S; Tilley, T Don

2015-05-26

Reactivity studies of the thermally stable ruthenostannylene complex [Cp*(IXy)(H)2 Ru-Sn-Trip] (1; IXy=1,3-bis(2,6-dimethylphenyl)imidazol-2-ylidene; Cp*=η(5) -C5 Me5 ; Trip=2,4,6-iPr3 C6 H2 ) with a variety of organic substrates are described. Complex 1 reacts with benzoin and an α,β-unsaturated ketone to undergo [1+4] cycloaddition reactions and afford [Cp*(IXy)(H)2 RuSn(κ(2) -O,O-OCPhCPhO)Trip] (2) and [Cp*(IXy)(H)2 RuSn(κ(2) -O,C-OCPhCHCHPh)Trip] (3), respectively. The reaction of 1 with ethyl diazoacetate resulted in a tin-substituted ketene complex [Cp*(IXy)(H)2 RuSn(OC2 H5 )(CHCO)Trip] (4), which is most likely a decomposition product from the putative ruthenium-substituted stannene complex. The isolation of a ruthenium-substituted stannene [Cp*(IXy)(H)2 RuSn(=Flu)Trip] (5) and stanna-imine [Cp*(IXy)(H)2 RuSn(κ(2) -N,O-NSO2 C6 H4 Me)Trip] (6) complexes was achieved by treatment of 1 with 9-diazofluorene and tosyl azide, respectively. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Platelet composite coatings for tin whisker mitigation

DOE PAGES

Rohwer, Lauren E. S.; Martin, James E.

2015-09-14

In this study, reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results formore » several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF 2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.« less

Platelet Composite Coatings for Tin Whisker Mitigation

NASA Astrophysics Data System (ADS)

Rohwer, Lauren E. S.; Martin, James E.

2015-11-01

Reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results for several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.

Nanocomposite TiN films with embedded MoS2 inorganic fullerenes produced by combining supersonic cluster beam deposition with cathodic arc reactive evaporation

NASA Astrophysics Data System (ADS)

Piazzoni, C.; Blomqvist, M.; Podestà, A.; Bardizza, G.; Bonati, M.; Piseri, P.; Milani, P.; Davies, C.; Hatto, P.; Ducati, C.; Sedláčková, K.; Radnóczi, G.

2008-01-01

We report the production and characterization of nanocomposite thin films consisting of a titanium nitride matrix with embedded molybdenum disulphide fullerene-like nanoparticles. This was achieved by combining a cluster source generating a pulsed supersonic beam of MoS2 clusters with an industrial cathodic arc reactive evaporation apparatus used for TiN deposition. Cluster-assembled films show the presence of MoS2 nanocages and nanostructures and the survival of such structures dispersed in the TiN matrix in the co-deposited samples. Nanotribological characterization by atomic force microscopy shows that the presence of MoS2 nanoparticles even in very low concentration modifies the behaviour of the TiN matrix.

N-cadherin in adult rat cardiomyocytes in culture. II. Spatio-temporal appearance of proteins involved in cell-cell contact and communication. Formation of two distinct N-cadherin/catenin complexes.

PubMed

Hertig, C M; Butz, S; Koch, S; Eppenberger-Eberhardt, M; Kemler, R; Eppenberger, H M

1996-01-01

The spatio-temporal appearance and distribution of proteins forming the intercalated disc were investigated in adult rat cardiomyocytes (ARC). The 'redifferentiation model' of ARC involves extensive remodelling of the plasma membrane and of the myofibrillar apparatus. It represents a valuable system to elucidate the formation of cell-cell contact between cardiomyocytes and to assess the mechanisms by which different proteins involved in the cell-cell adhesion process are sorted in a precise manner to the sites of function. Appearance of N-cadherin, the catenins and connexin43 within newly formed adherens and gap junctions was studied. Here first evidence is provided for a formation of two distinct and separable N-cadherin/catenin complexes in cardiomyocytes. Both complexes are composed of N-cadherin and alpha-catenin which bind to either beta-catenin or plakoglobin in a mutually exclusive manner. The two N-cadherin/catenin complexes are assumed to be functionally involved in the formation of cell-cell contacts in ARC; however, the differential appearance and localization of the two types of complexes may also point to a specific role during ARC differentiation. The newly synthesized beta-catenin containing complex is more abundant during the first stages in culture after ARC isolation, while the newly synthesized plakoglobin containing complex progressively accumulates during the morphological changes of ARC. ARC formed a tissue-like pattern in culture whereby the new cell-cell contacts could be dissolved through Ca2+ depletion. Presence of cAMP and replenishment of Ca2+ content in the culture medium not only allowed reformation of cell-cell contacts but also affected the relative protein ratio between the two N-cadherin/catenin complexes, increasing the relative amount of newly synthesized beta-catenin over plakoglobin at a particular stage of ARC differentiation. The clustered N-cadherin/catenin complexes at the plasma membrane appear to be a prerequisite for the following gap junction formation; a temporal sequence of the appearance of adherens junction proteins and of gap junctions forming connexin-43 is suggested.

Adhesive F-actin Waves: A Novel Integrin-Mediated Adhesion Complex Coupled to Ventral Actin Polymerization

PubMed Central

Case, Lindsay B.; Waterman, Clare M.

2011-01-01

At the leading lamellipodium of migrating cells, protrusion of an Arp2/3-nucleated actin network is coupled to formation of integrin-based adhesions, suggesting that Arp2/3-mediated actin polymerization and integrin-dependent adhesion may be mechanistically linked. Arp2/3 also mediates actin polymerization in structures distinct from the lamellipodium, in “ventral F-actin waves” that propagate as spots and wavefronts along the ventral plasma membrane. Here we show that integrins engage the extracellular matrix downstream of ventral F-actin waves in several mammalian cell lines as well as in primary mouse embryonic fibroblasts. These “adhesive F-actin waves” require a cycle of integrin engagement and disengagement to the extracellular matrix for their formation and propagation, and exhibit morphometry and a hierarchical assembly and disassembly mechanism distinct from other integrin-containing structures. After Arp2/3-mediated actin polymerization, zyxin and VASP are co-recruited to adhesive F-actin waves, followed by paxillin and vinculin, and finally talin and integrin. Adhesive F-actin waves thus represent a previously uncharacterized integrin-based adhesion complex associated with Arp2/3-mediated actin polymerization. PMID:22069459

Biomass Scenario Model Documentation: Data and References

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Y.; Newes, E.; Bush, B.

2013-05-01

The Biomass Scenario Model (BSM) is a system dynamics model that represents the entire biomass-to-biofuels supply chain, from feedstock to fuel use. The BSM is a complex model that has been used for extensive analyses; the model and its results can be better understood if input data used for initialization and calibration are well-characterized. It has been carefully validated and calibrated against the available data, with data gaps filled in using expert opinion and internally consistent assumed values. Most of the main data sources that feed into the model are recognized as baseline values by the industry. This report documentsmore » data sources and references in Version 2 of the BSM (BSM2), which only contains the ethanol pathway, although subsequent versions of the BSM contain multiple conversion pathways. The BSM2 contains over 12,000 total input values, with 506 distinct variables. Many of the variables are opportunities for the user to define scenarios, while others are simply used to initialize a stock, such as the initial number of biorefineries. However, around 35% of the distinct variables are defined by external sources, such as models or reports. The focus of this report is to provide insight into which sources are most influential in each area of the supply chain.« less

Uncoupling of transcription and translation of Fanconi anemia (FANC) complex proteins during spermatogenesis

PubMed Central

Jamsai, Duangporn; O’Connor, Anne E; O’Donnell, Liza; Lo, Jennifer Chi Yi; O’Bryan, Moira K

2015-01-01

Male germ cell genome integrity is critical for spermatogenesis, fertility and normal development of the offspring. Several DNA repair pathways exist in male germ cells. One such important pathway is the Fanconi anemia (FANC) pathway. Unlike in somatic cells, expression profiles and the role of the FANC pathway in germ cells remain largely unknown. In this study, we undertook an extensive expression analyses at both mRNA and protein levels of key components of the FANC pathway during spermatogenesis in the mouse. Herein we show that Fanc mRNAs and proteins displayed developmental enrichment within particular male germ cell types. Spermatogonia and pre-leptotene spermatocytes contained the majority of the FANC components examined i.e. complex I members FANCB, FANCG and FANCM, complex II members FANCD2 and FANCI, and complex III member FANCJ. Leptotene, zygotene and early pachytene spermatocytes contained FANCB, FANCG, FANCM and FANCD2. With the exception of FANCL, all FANC proteins examined were not detected in round spermatids. Elongating and elongated spermatids contained FANCB, FANCG, FANCL and FANCJ. qPCR analysis on isolated spermatocytes and round spermatids showed that Fancg, Fancl, Fancm, Fancd2, Fanci and Fancj mRNAs were expressed in both of these germ cell types, indicating that some degree of translational repression of these FANC proteins occurs during the transition from meiosis to spermiogenesis. Taken together, our findings raise the possibility that the assembly of FANC protein complexes in each of the male germ cell type is unique and may be distinct from the proposed model in mitotic cells. PMID:26413409

Preparation of TiN films by reactive high-power pulsed sputtering Penning discharges

NASA Astrophysics Data System (ADS)

Kimura, Takashi; Yoshida, Ryo; Mishima, Toshihiko; Azuma, Kingo; Nakao, Setsuo

2018-06-01

Titanium nitride (TiN) films are prepared by reactive high-power pulsed sputtering Penning discharges at a total pressure of 0.7 Pa and an average power of 60 W, where the nitrogen fraction is varied up to 15%. The peak value of the instantaneous power ranges between 3 and 14 kW, and the peak power density ranges between 0.3 and 1.2 kW cm‑2. The hardness of TiN films is higher than 22 GPa at the nitrogen fractions lower than 10% and it reaches 31 GPa at a nitrogen fraction of 5%. The X-ray diffraction peak of TiN(111) texture is observed for all prepared films, showing the grain size of about 10 nm. In X-ray photoelectron spectroscopy, oxygen is mainly bonded to titanium, but the intensity of the TiN bond is dominant in the entire Ti 2p spectrum. The intensity ratio of N 1s to Ti 2p ranges between 0.85 and 0.95.

Epitaxial integration of CoFe2O4 thin films on Si (001) surfaces using TiN buffer layers

NASA Astrophysics Data System (ADS)

Prieto, Pilar; Marco, José F.; Prieto, José E.; Ruiz-Gomez, Sandra; Perez, Lucas; del Real, Rafael P.; Vázquez, Manuel; de la Figuera, Juan

2018-04-01

Epitaxial cobalt ferrite thin films with strong in-plane magnetic anisotropy have been grown on Si (001) substrates using a TiN buffer layer. The epitaxial films have been grown by ion beam sputtering using either metallic, CoFe2, or ceramic, CoFe2O4, targets. X-ray diffraction (XRD) and Rutherford spectrometry (RBS) in random and channeling configuration have been used to determine the epitaxial relationship CoFe2O4 [100]/TiN [100]/Si [100]. Mössbauer spectroscopy, in combination with XRD and RBS, has been used to determine the composition and structure of the cobalt ferrite thin films. The TiN buffer layer induces a compressive strain in the cobalt ferrite thin films giving rise to an in-plane magnetic anisotropy. The degree of in-plane anisotropy depends on the lattice mismatch between CoFe2O4 and TiN, which is larger for CoFe2O4 thin films grown on the reactive sputtering process with ceramic targets.

Fabrication and Measurement of Electroluminescence and Electrical Properties of Organic Light-Emitting Diodes Containing Mott Insulator Nanocrystals.

PubMed

Nozoe, Soichiro; Kinoshita, Nobuaki; Matsuda, Masaki

2016-04-01

By using the short-time electrocrystallization technique, phthalocyanine (Pc)-based Mott insulator Co(Pc)(CN)2 . 2CHCl3 nanocrystals were fabricated and applied to organic light-emiting diodes (OLEDs). The fabricated device having the configuration ITO/Co(Pc)(CN)2 . 2CHCl3/Alq3/Al, in which ITO is indium-tin oxide and Alq3 is tris(8-hydroxyquinolinato)aluminum, showed clear emission from Alq3, suggesting the Mott insulator Co(Pc)(CN)2 . 2CHCl3 can work as useful hole-injection and transport material in OLEDs.

Combinatorial electrochemical cell array for high throughput screening of micro-fuel-cells and metal/air batteries.

PubMed

Jiang, Rongzhong

2007-07-01

An electrochemical cell array was designed that contains a common air electrode and 16 microanodes for high throughput screening of both fuel cells (based on polymer electrolyte membrane) and metal/air batteries (based on liquid electrolyte). Electrode materials can easily be coated on the anodes of the electrochemical cell array and screened by switching a graphite probe from one cell to the others. The electrochemical cell array was used to study direct methanol fuel cells (DMFCs), including high throughput screening of electrode catalysts and determination of optimum operating conditions. For screening of DMFCs, there is about 6% relative standard deviation (percentage of standard deviation versus mean value) for discharge current from 10 to 20 mAcm(2). The electrochemical cell array was also used to study tin/air batteries. The effect of Cu content in the anode electrode on the discharge performance of the tin/air battery was investigated. The relative standard deviations for screening of metal/air battery (based on zinc/air) are 2.4%, 3.6%, and 5.1% for discharge current at 50, 100, and 150 mAcm(2), respectively.

26 CFR 301.6721-0 - Table of Contents.

Code of Federal Regulations, 2011 CFR

2011-04-01

... TINs. (1) In general. (i) Initial solicitation. (ii) First annual solicitation. (iii) Second annual.... (f) Acting in a responsible manner—special rules for incorrect TINs. (1) In general. (i) Initial...) In general. (2) Special rules relating to TINs. (3) Effective dates. (h) Transitional rules for...

26 CFR 301.6721-0 - Table of Contents.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TINs. (1) In general. (i) Initial solicitation. (ii) First annual solicitation. (iii) Second annual.... (f) Acting in a responsible manner—special rules for incorrect TINs. (1) In general. (i) Initial...) In general. (2) Special rules relating to TINs. (3) Effective dates. (h) Transitional rules for...

Enhancement of conversion efficiency of extreme ultraviolet radiation from a liquid aqueous solution microjet target by use of dual laser pulses

NASA Astrophysics Data System (ADS)

Higashiguchi, Takeshi; Dojyo, Naoto; Hamada, Masaya; Kawasaki, Keita; Sasaki, Wataru; Kubodera, Shoichi

2006-03-01

We demonstrated a debris-free, efficient laser-produced plasma extreme ultraviolet (EUV) source by use of a regenerative liquid microjet target containing tin-dioxide (SnO II) nano-particles. By using a low SnO II concentration (6%) solution and dual laser pulses for the plasma control, we observed the EUV conversion efficiency of 1.2% with undetectable debris.

26 CFR 1.6050H-2 - Time, form, and manner of reporting interest received on qualified mortgage.

Code of Federal Regulations, 2014 CFR

2014-04-01

... taxpayer identification number (TIN) (as defined in section 7701(a)(41)) of the payor of record; (ii) The name, address, and TIN of the interest recipient; (iii) The amount of interest (other than points... paragraph (a)(2)(ii) of this section by including on Form 1098 (and Form 1096) the name, address, and TIN of...

26 CFR 1.6050H-2 - Time, form, and manner of reporting interest received on qualified mortgage.

Code of Federal Regulations, 2010 CFR

2010-04-01

... taxpayer identification number (TIN) (as defined in section 7701(a)(41)) of the payor of record; (ii) The name, address, and TIN of the interest recipient; (iii) The amount of interest (other than points... paragraph (a)(2)(ii) of this section by including on Form 1098 (and Form 1096) the name, address, and TIN of...

26 CFR 1.6050H-2 - Time, form, and manner of reporting interest received on qualified mortgage.

Code of Federal Regulations, 2011 CFR

2011-04-01

... taxpayer identification number (TIN) (as defined in section 7701(a)(41)) of the payor of record; (ii) The name, address, and TIN of the interest recipient; (iii) The amount of interest (other than points... paragraph (a)(2)(ii) of this section by including on Form 1098 (and Form 1096) the name, address, and TIN of...

26 CFR 1.6050H-2 - Time, form, and manner of reporting interest received on qualified mortgage.

Code of Federal Regulations, 2013 CFR

2013-04-01

... taxpayer identification number (TIN) (as defined in section 7701(a)(41)) of the payor of record; (ii) The name, address, and TIN of the interest recipient; (iii) The amount of interest (other than points... paragraph (a)(2)(ii) of this section by including on Form 1098 (and Form 1096) the name, address, and TIN of...

26 CFR 1.6050H-2 - Time, form, and manner of reporting interest received on qualified mortgage.

Code of Federal Regulations, 2012 CFR

2012-04-01

... taxpayer identification number (TIN) (as defined in section 7701(a)(41)) of the payor of record; (ii) The name, address, and TIN of the interest recipient; (iii) The amount of interest (other than points... paragraph (a)(2)(ii) of this section by including on Form 1098 (and Form 1096) the name, address, and TIN of...

Multiple complexes of nitrogen assimilatory enzymes in spinach chloroplasts: possible mechanisms for the regulation of enzyme function.

PubMed

Kimata-Ariga, Yoko; Hase, Toshiharu

2014-01-01

Assimilation of nitrogen is an essential biological process for plant growth and productivity. Here we show that three chloroplast enzymes involved in nitrogen assimilation, glutamate synthase (GOGAT), nitrite reductase (NiR) and glutamine synthetase (GS), separately assemble into distinct protein complexes in spinach chloroplasts, as analyzed by western blots under blue native electrophoresis (BN-PAGE). GOGAT and NiR were present not only as monomers, but also as novel complexes with a discrete size (730 kDa) and multiple sizes (>120 kDa), respectively, in the stromal fraction of chloroplasts. These complexes showed the same mobility as each monomer on two-dimensional (2D) SDS-PAGE after BN-PAGE. The 730 kDa complex containing GOGAT dissociated into monomers, and multiple complexes of NiR reversibly converted into monomers, in response to the changes in the pH of the stromal solvent. On the other hand, the bands detected by anti-GS antibody were present not only in stroma as a conventional decameric holoenzyme complex of 420 kDa, but also in thylakoids as a novel complex of 560 kDa. The polypeptide in the 560 kDa complex showed slower mobility than that of the 420 kDa complex on the 2D SDS-PAGE, implying the assembly of distinct GS isoforms or a post-translational modification of the same GS protein. The function of these multiple complexes was evaluated by in-gel GS activity under native conditions and by the binding ability of NiR and GOGAT with their physiological electron donor, ferredoxin. The results indicate that these multiplicities in size and localization of the three nitrogen assimilatory enzymes may be involved in the physiological regulation of their enzyme function, in a similar way as recently described cases of carbon assimilatory enzymes.

The Role of Mammalian Target of Rapamycin (mTOR) in Insulin Signaling.

PubMed

Yoon, Mee-Sup

2017-10-27

The mammalian target of rapamycin (mTOR) is a serine/threonine kinase that controls a wide spectrum of cellular processes, including cell growth, differentiation, and metabolism. mTOR forms two distinct multiprotein complexes known as mTOR complex 1 (mTORC1) and mTOR complex 2 (mTORC2), which are characterized by the presence of raptor and rictor, respectively. mTOR controls insulin signaling by regulating several downstream components such as growth factor receptor-bound protein 10 (Grb10), insulin receptor substrate (IRS-1), F-box/WD repeat-containing protein 8 (Fbw8), and insulin like growth factor 1 receptor/insulin receptor (IGF-IR/IR). In addition, mTORC1 and mTORC2 regulate each other through a feedback loop to control cell growth. This review outlines the current understanding of mTOR regulation in insulin signaling in the context of whole body metabolism.

A new method for the preparation of a [Sn2(H2PO2)3]Br SHG-active polar crystal via surfactant-induced strategy.

PubMed

Xie, Jie-Ling; Zhou, Yu-Hua; Li, Long-Hua; Zhang, Jian-Han; Song, Jun-Ling

2017-07-25

Herein, unprecedented NLO-brominated tin hypophosphites, namely [Sn 2 (H 2 PO 2 ) 3 ]Br, were discovered via a facile surfactant-induced method, which displayed a moderate powder SHG intensity (3.0 × KDP) in type - I phase matching behavior. This complex has high chemical and thermal stability at room temperature. DFT calculations and SHG coefficient analyses revealed that the alignment of the SHG-active-units SnO 3 trigonal pyramids and Br - anions in its structure mainly contribute to the macroscopical SHG behaviors.

Effect of doping of tin on optoelectronic properties of indium oxide: DFT study

NASA Astrophysics Data System (ADS)

Tripathi, Madhvendra Nath

2015-06-01

Indium tin oxide is widely used transparent conductor. Experimentally observed that 6% tin doping in indium oxide is suitable for optoelectronic applications and more doping beyond this limit degrades the optoelectronic property. The stoichiometry (In32-xSnxO48+x/2; x=0-6) is taken to understand the change in lattice parameter, electronic structure, and optical property of ITO. It is observed that lattice parameter increases and becomes constant after 6% tin doping that is in good agreement of the experimental observation. The electronic structure calculation shows that the high tin doping in indium oxide adversely affects the dispersive nature of the bottom of conduction band of pure indium oxide and decreases the carrier mobility. Optical calculations show that transmittance goes down upto 60% for the tin concentration more than 6%. The present paper shows that how more than 6% tin doping in indium oxide adversely affects the optoelectronic property of ITO.

Tin-Assisted Synthesis of ɛ -Ga2O3 by Molecular Beam Epitaxy

NASA Astrophysics Data System (ADS)

Kracht, M.; Karg, A.; Schörmann, J.; Weinhold, M.; Zink, D.; Michel, F.; Rohnke, M.; Schowalter, M.; Gerken, B.; Rosenauer, A.; Klar, P. J.; Janek, J.; Eickhoff, M.

2017-11-01

The synthesis of ɛ -Ga2O3 and β -Ga2O3 by plasma-assisted molecular beam epitaxy on (001 )Al2O3 substrates is studied. The growth window of β -Ga2O3 in the Ga-rich regime, usually limited by the formation of volatile gallium suboxide, is expanded due to the presence of tin during the growth process, which stabilizes the formation of gallium oxides. X-ray diffraction, transmission electron microscopy, time-of-flight secondary-ion mass spectrometry, Raman spectroscopy, and atomic force microscopy are used to analyze the influence of tin on the layer formation. We demonstrate that it allows the synthesis of phase-pure ɛ -Ga2O3 . A growth model based on the oxidation of gallium suboxide by reduction of an intermediate sacrificial tin oxide is suggested.

Thermally evaporated mechanically hard tin oxide thin films for opto-electronic apllications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tripathy, Sumanta K.; Rajeswari, V. P.

2014-01-28

Tungsten doped tin oxide (WTO) and Molybdenum doped tin oxide (MoTO) thin film were deposited on corn glass by thermal evaporation method. The films were annealed at 350°C for one hour. Structural analysis using Xray diffraction data shows both the films are polycrystalline in nature with monoclinic structure of tin oxide, Sn{sub 3}O{sub 4}, corresponding to JCPDS card number 01-078-6064. SEM photograph showed that both the films have spherical grains with size in the range of 20–30 nm. Compositional analysis was carried out using EDS which reveals the presence of Sn, O and the dopant Mo/W only thereby indicating themore » absence of any secondary phase in the films. The films are found to contain nearly 6 wt% of Mo, 8 wt% of W as dopants respectively. The transmission pattern for both the films in the spectral range 200 – 2000 nm shows that W doping gives a transparency of nearly 80% from 380 nm onwards while Mo doping has less transparency of 39% at 380nm. Film hardness measurement using Triboscope shows a film hardness of about 9–10 GPa for both the films. It indicates that W or M doping in tin oxide provides the films the added advantage of withstanding the mechanical wear and tear due to environmental fluctuations By optimizing the optical and electrical properties, W/Mo doped tin oxide films may be explored as window layers in opto-electronic applications such as solar cells.« less

Flow Visualization of Low Prandtl Number Fluids using Electrochemical Measurements

NASA Technical Reports Server (NTRS)

Crunkleton, D.; Anderson, T.; Narayanan, R.; Labrosse, G.

2003-01-01

It is well established that residual flows exist in contained liquid metal processes. In 1-g processing, buoyancy forces often drive these flows and their magnitudes can be substantial. It is also known that residual flows can exist during microgravity processing, and although greatly reduced in magnitude, they can influence the properties of the processed materials. Unfortunately, there are very few techniques to visualize flows in opaque, high temperature liquid metals, and those available are not easily adapted to flight investigation. In this study, a novel technique is developed that uses liquid tin as the model fluid and solid-state electrochemical cells constructed from Yttria-Stabilized Zirconia (YSZ) to establish and measure dissolved oxygen boundary conditions. The melt serves as a common electrode for each of the electrochemical cells in this design, while independent reference electrodes are maintained at the outside surfaces of the electrolyte. By constructing isolated electrochemical cells at various locations along the container walls, oxygen is introduced or extracted by imposing a known electrical potential or passing a given current between the melt and the reference electrode. This programmed titration then establishes a known oxygen concentration boundary condition at the selected electrolyte-melt interface. Using the other cells, the concentration of oxygen at the electrolyte-melt interface is also monitored by measuring the open-circuit potentials developed between the melt and reference electrodes. Thus the electrochemical cells serve to both establish boundary conditions for the passive tracer and sense its path. Rayleigh-Benard convection was used to validate the electrochemical approach to flow visualization. Thus, a numerical characterization of the second critical Rayleigh numbers in liquid tin was conducted for a variety of Cartesian aspect ratios. The extremely low Prandtl number of tin represents the lowest value studied numerically. Additionally, flow field oscillations are visualized and the effect of tilt on convecting systems is quantified. Experimental studies of the effect of convection in liquid tin are presented. Three geometries are studied: (1) double electrochemical cell with vertical concentration gradients; (2) double cell with horizontal concentration gradients; and (3) multiple cells with vertical temperature gradients. The first critical Rayleigh number transition is detected with geometry (1) and it is concluded that current measurements are not as affected by convection as EMF measurements. The system is compared with numerical simulations in geometry (2), and oscillating convection is detected with geometry (3).

Isolation and characterization of Staufen-containing ribonucleoprotein particles from rat brain.

PubMed

Mallardo, Massimo; Deitinghoff, Anke; Müller, Juliane; Goetze, Bernhard; Macchi, Paolo; Peters, Christopher; Kiebler, Michael A

2003-02-18

Localized mRNAs are thought to be transported in defined particles to their final destination. These particles represent large protein complexes that may be involved in recognizing, transporting, and anchoring localized messages. Few components of these ribonucleoparticles, however, have been identified yet. We chose the strategy to biochemically enrich native RNA-protein complexes involved in RNA transport to identify the associated RNAs and proteins. Because Staufen proteins were implicated in intracellular RNA transport, we chose mammalian Staufen proteins as markers for the purification of RNA transport particles. Here, we present evidence that Staufen proteins exist in two different complexes: (i) distinct large, ribosome- and endoplasmic reticulum-containing granules preferentially found in the membrane pellets during differential centrifugation and (ii) smaller particles in the S100 from rat brain homogenates. On gel filtration of the S100, we identified soluble 670-kDa Staufen1-containing and 440-kDa Staufen2-containing particles. They do not cofractionate with ribosomes and endoplasmic reticulum but rather coenrich with kinesin heavy chain. Furthermore, the fractions containing the Staufen1 particles show a 15-fold enrichment of mRNAs compared with control fractions. Most importantly, these fractions are highly enriched in BC1, and, to a lesser extent, in the alpha-subunit of the Ca(2+)/calmodulin-dependent kinase II, two dendritically localized RNAs. Finally, both RNAs colocalize with Staufen1-hemagglutinin in particles in dendrites of transfected hippocampal neurons. We therefore propose that these Staufen1-containing particles may represent RNA transport intermediates that are in transit to their final destination within neurons.

Isolation and characterization of Staufen-containing ribonucleoprotein particles from rat brain

PubMed Central

Mallardo, Massimo; Deitinghoff, Anke; Müller, Juliane; Goetze, Bernhard; Macchi, Paolo; Peters, Christopher; Kiebler, Michael A.

2003-01-01

Localized mRNAs are thought to be transported in defined particles to their final destination. These particles represent large protein complexes that may be involved in recognizing, transporting, and anchoring localized messages. Few components of these ribonucleoparticles, however, have been identified yet. We chose the strategy to biochemically enrich native RNA–protein complexes involved in RNA transport to identify the associated RNAs and proteins. Because Staufen proteins were implicated in intracellular RNA transport, we chose mammalian Staufen proteins as markers for the purification of RNA transport particles. Here, we present evidence that Staufen proteins exist in two different complexes: (i) distinct large, ribosome- and endoplasmic reticulum-containing granules preferentially found in the membrane pellets during differential centrifugation and (ii) smaller particles in the S100 from rat brain homogenates. On gel filtration of the S100, we identified soluble 670-kDa Staufen1-containing and 440-kDa Staufen2-containing particles. They do not cofractionate with ribosomes and endoplasmic reticulum but rather coenrich with kinesin heavy chain. Furthermore, the fractions containing the Staufen1 particles show a 15-fold enrichment of mRNAs compared with control fractions. Most importantly, these fractions are highly enriched in BC1, and, to a lesser extent, in the α-subunit of the Ca2+/calmodulin-dependent kinase II, two dendritically localized RNAs. Finally, both RNAs colocalize with Staufen1–hemagglutinin in particles in dendrites of transfected hippocampal neurons. We therefore propose that these Staufen1-containing particles may represent RNA transport intermediates that are in transit to their final destination within neurons. PMID:12592035

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2012 CFR

2012-10-01

..., contact name and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN is the social security number (SSN). (2) Information provided when registering for an FRN must... as it deems appropriate for its business operations. Each subsidiary with a different TIN must obtain...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2014 CFR

2014-10-01

..., contact name and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN is the social security number (SSN). (2) Information provided when registering for an FRN must... as it deems appropriate for its business operations. Each subsidiary with a different TIN must obtain...

47 CFR 1.8002 - Obtaining an FRN.

Code of Federal Regulations, 2013 CFR

2013-10-01

..., contact name and title, address, and taxpayer identifying number (TIN) must be provided. For individuals, the TIN is the social security number (SSN). (2) Information provided when registering for an FRN must... as it deems appropriate for its business operations. Each subsidiary with a different TIN must obtain...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

40 CFR 421.294 - Standards of performance for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Secondary Tin... achieve the following new source performance standards: (a) Tin smelter SO2 scrubber. NSPS for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum for monthly average...

Occurrences and inventories of heavy metals and brominated flame retardants in wastes from printed circuit board production.

PubMed

Zhou, Xiaoyu; Guo, Jie; Zhang, Wei; Zhou, Peng; Deng, Jingjing; Lin, Kuangfei

2014-09-01

Pollutants including heavy metals and brominated flame retardant were detected in 10 types of production wastes from a typical printed circuit board manufacturing plant, and their inventories were estimated. Rinsing water from etching process had the highest concentrations of copper (665.51 mg/L), lead (1.02 mg/L), nickel (3.60 mg/L), chromium (0.97 mg/L), and tin (1.79 mg/L). Powdered solid waste (SW) from the cut lamination process contained the highest tetrabromobisphenol-A (TBBPA) levels (49.86 mg/kg). Polybrominated diphenyl ethers (PBDEs) were absent in this plant, in agreement with the international regulations of PBDE phase out. The pollutant inventories in the wastes exhibited in the order of copper > > zinc > tin ≈ nickel > lead > chromium > > TBBPA. The potential environmental impact of pollutants in SW during production and disposal were further investigated. A high partitioning of pollutant concentration between the total suspended particle and SW (-0.10 < log K TS < 2.12) was observed for most pollutants, indicating the emission pathway from SW to the airborne atmosphere in the workshop. Although SW met the toxicity characteristic leaching procedure, drilling powder with the smallest particle diameter still showed high leachabilities of lead and tin which may lead to a negative environmental impact during disposal.

Photonic Nanoparticle Doped Architectures for Enhanced Solar to Fuel Photocatalytic Conversion 154060

DTIC Science & Technology

2016-12-09

coverage of the ZIS shell. We are also exploring the use of nanoshells coated with tin oxide (SnO2) rather than silica (SiO2) and coating the GS-NSs with...exploring the use of nanoshells coated with tin oxide (SnO2) rather than silica (SiO2) and coating the GS-NSs with zinc- and antimony-doped SnO2...to the preparation of GS-NS@SiO2 particles, we are also exploring the GS-NS coated with tin oxide (SnO2) and doped SnO2. Nanoshells with other

Relative toxicity of lead and five proposed substitute shot types to pen-reared mallards

USGS Publications Warehouse

Grandy, John W.; Locke, Louis N.; Bagley, George E.

1968-01-01

A 30-day toxicity test was made to determine the relative toxicity of lead, a tin-lead alloy, zinc, nickel, teflon-coated steel, and tin, all in shot form, to pen-reared mallard drakes. All of the 15 ducks dosed with lead died. Twenty-seven percent of 15 dosed with alloy, and 20 percent of 15 dosed with zinc also died. Ten of the remaining zinc-dosed ducks showed signs of distress, including losses of muscular control and body weight. There were no deaths among 15 ducks dosed with nickel, 15 dosed with teflon-coated steel, and 15 dosed with tin. Seventy-three percent of those dosed with nickel shot eliminated all shot before the end of the 30-day period. Acid-fast intranuclear inclusion bodies were present in the kidneys of mallards dosed with commercial lead shot, or with tin-lead alloy shot, but not in the kidneys of birds given nickel, tin, or teflon-coated steel shot. Atypical, pale, acid-fast bodies were found in kidneys of 1 of 15 birds dosed with zinc. An iron-containing pigment, which stained positive with the Prussian blue technique, was present in variable amounts in almost all livers. Zinc-dosed ducks that died or were killed while still showing signs of zinc intoxication had higher iron levels in the liver than ducks that had recovered from zinc intoxication.

Effect of Magnesium and Osteoblast Cell Presence on Hydroxyapatite Formation on (Ti,Mg)N Thin Film Coatings

NASA Astrophysics Data System (ADS)

Onder, Sakip; Calikoglu-Koyuncu, Ayse Ceren; Torun Kose, Gamze; Kazmanli, Kursat; Kok, Fatma Nese; Urgen, Mustafa

2017-07-01

TiN and (Ti,Mg)N thin film coatings were deposited on Ti substrates by an arc-physical vapor deposition technique. The effect of cell presence on hydroxyapatite (HA) formation was investigated using surfaces with four different Mg contents (0, 8.1, 11.31, and 28.49 at.%). Accelerated corrosion above 10 at.% Mg had a negative effect on the performance in terms of both cell proliferation and mineralization. In the absence of cells, Mg-free TiN coatings and low-Mg (8.1 at.%)-doped (Ti,Mg)N surfaces led to an early HA deposition (after 7 days and 14 days, respectively) in cell culture medium (DMEM), but the crystallinity was low. More crystalline HA structures were obtained in the presence of the cells. HA deposits with an ideal Ca/P ratio were obtained at least a week earlier, at day 14, in TiN and low-Mg (8.1 at.%)-doped (Ti,Mg)N compared with that of high-Mg-containing surfaces (>10 at.%). A thicker mineralized matrix was formed on low-Mg (8.1 at.%)-doped (Ti,Mg)N relative to that of the TiN sample. Low-Mg doping (<10 at.%) into TiN coatings resulted in better cell proliferation and thicker mineralized matrix formation, so it could be a promising alternative for hard tissue applications.

40 CFR 60.131 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... containing copper as its predominant constituent, and lesser amounts of zinc, tin, lead, or other metals. (b... heat required in the production of refined brass or bronze. (d) Blast furnace means any furnace used to...

40 CFR 60.131 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... containing copper as its predominant constituent, and lesser amounts of zinc, tin, lead, or other metals. (b... heat required in the production of refined brass or bronze. (d) Blast furnace means any furnace used to...

Self-catalyzed carbon plasma-assisted growth of tin-doped indium oxide nanostructures by the sputtering method

NASA Astrophysics Data System (ADS)

Setti, Grazielle O.; de Jesus, Dosil P.; Joanni, Ednan

2016-10-01

In this work a new strategy for growth of nanostructured indium tin oxide (ITO) by RF sputtering is presented. ITO is deposited in the presence of a carbon plasma which reacts with the free oxygen atoms during the deposition, forming species like CO x . These species are removed from the chamber by the pumping system, and one-dimensional ITO nanostructures are formed without the need for a seed layer. Different values of substrate temperature and power applied to the gun containing the carbon target were investigated, resulting in different nanostructure morphologies. The samples containing a higher density of nanowires were covered with gold and evaluated as surface-enhanced Raman scattering substrates for detection of dye solutions. The concept might be applied to other oxides, providing a simple method for unidimensional nanostructural synthesis.

Estimating the Probability of Electrical Short Circuits from Tin Whiskers. Part 2

NASA Technical Reports Server (NTRS)

Courey, Karim J.; Asfour, Shihab S.; Onar, Arzu; Bayliss, Jon A.; Ludwig, Larry L.; Wright, Maria C.

2009-01-01

To comply with lead-free legislation, many manufacturers have converted from tin-lead to pure tin finishes of electronic components. However, pure tin finishes have a greater propensity to grow tin whiskers than tin-lead finishes. Since tin whiskers present an electrical short circuit hazard in electronic components, simulations have been developed to quantify the risk of said short circuits occurring. Existing risk simulations make the assumption that when a free tin whisker has bridged two adjacent exposed electrical conductors, the result is an electrical short circuit. This conservative assumption is made because shorting is a random event that had an unknown probability associated with it. Note however that due to contact resistance electrical shorts may not occur at lower voltage levels. In our first article we developed an empirical probability model for tin whisker shorting. In this paper, we develop a more comprehensive empirical model using a refined experiment with a larger sample size, in which we studied the effect of varying voltage on the breakdown of the contact resistance which leads to a short circuit. From the resulting data we estimated the probability distribution of an electrical short, as a function of voltage.

42 CFR 414.1205 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... physicians means a single Tax Identification Number (TIN) with 2 or more eligible professionals, as... rights to the TIN. Performance period means the calendar year that will be used to assess the quality of...) model. Taxpayer Identification Number (TIN) has the same meaning given this term under § 425.20 of this...

42 CFR 414.1205 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... physicians means a single Tax Identification Number (TIN) with 2 or more eligible professionals, as... rights to the TIN. Performance period means the calendar year that will be used to assess the quality of...) model. Taxpayer Identification Number (TIN) has the same meaning given this term under § 425.20 of this...

78 FR 54986 - Information Reporting of Minimum Essential Coverage

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-09

... to report (1) the name, address, and taxpayer identification number (TIN) of the primary insured, (2) the name, dates of coverage, and TIN of each individual covered under a policy, (3) whether health... effect, the names and TINs of each individual covered, the amount of advance credit payments relating to...

Metal Nanoshells for Plasmonically Enhanced Solar to Fuel Photocatalytic Conversion

DTIC Science & Technology

2016-05-18

interlayer of ~17 nm generated a rate of hydrogen production 2.6 times higher than that of unmodified ZIS. Second thrust: Tin oxide-coated gold-silver...nanoshells were prepared as an alternative plasmonic enhancement system to the silicon oxide system described above. Tin oxide is an attractive...this grant, we developed two synthetic approaches for preparing tin oxide-coated gold-silver nanoshells, as illustrated in Scheme 2. These particles

The Conterminous United States Mineral Assessment Program; background information to accompany folio of geologic and mineral resource maps of the Silver City 1 degree x 2 degrees Quadrangle, New Mexico and Arizona

USGS Publications Warehouse

Richter, Donald H.; Houser, B.B.; Watts, K.C.; Klein, D.P.; Sharp, W.N.; Drewes, Harald; Hedlund, D.C.; Raines, G.L.; Hassemer, J.R.

1987-01-01

The Silver City 1 ? x 2 ? quadrangle, consisting of about 20,650 km2 in southwestern New Mexico and southeastern Arizona, has been investigated by a multidisciplinary research team for the purpose of assessing its mineral resource potential. The results of this investigation are in a folio of 21 maps that contain detailed information on the geology, geochemistry, geophysics, mineral deposits, and potential mineral resources of the quadrangle. This Circular provides background information on the various studies and integrates the component maps. It contains an extensive selected bibliography pertinent to the geology and mineral deposits of the quadrangle. The quadrangle has produced more than $3.5 billion in mineral products since about 1850 and contains significant resources of gold, silver, copper, molybdenum, lead, zinc, iron, manganese-iron, zeolite minerals, and possibly tin and tungsten.

Nucleation and growth of tin whiskers

NASA Astrophysics Data System (ADS)

Cheng, Jing; Vianco, Paul T.; Zhang, Bei; Li, James C. M.

2011-06-01

Pure tin film of one micron thick was evaporated onto a silicon substrate with chromium and nickel underlayers. The tinned silicon disk was bent by applying a dead load at the center and supported below around the edge to apply biaxial compressive stresses to the tin layer. After 180 C vacuum annealing for 1,2,4,6, and 8 weeks, tin whiskers/hillocks grew. A quantitative method revealed that the overall growth rate decreased with time with a tendency for saturation. A review of the literature showed in general, tin whisker growth has a nucleation period, a growth period and a period of saturation, very similar to recrystallization or phase transformation. In fact we found our data fit Avrami equation very well. This equation shows that the nucleation period was the first week.

Method of joining ITM materials using a partially or fully-transient liquid phase

DOEpatents

Butt, Darryl Paul; Cutler, Raymond Ashton; Rynders, Steven Walton; Carolan, Michael Francis

2006-03-14

A method of forming a composite structure includes: (1) providing first and second sintered bodies containing first and second multicomponent metallic oxides having first and second identical crystal structures that are perovskitic or fluoritic; (2) providing a joint material containing at least one metal oxide: (a) containing (i) at least one metal of an identical IUPAC Group as at least one sintered body metal in one of the multicomponent metallic oxides, (ii) a first row D-Block transition metal not contained in the multicomponent metallic oxides, and/or (iii) a lanthanide not contained in the multicomponent metallic oxides; (b) free of metals contained in the multicomponent metallic oxides; (c) free of cations of boron, silicon, germanium, tin, lead, arsenic, antimony, phosphorus and tellurium; and (d) having a melting point below the sintering temperatures of the sintered bodies; and (3) heating to a joining temperature above the melting point and below the sintering temperatures.

Surface reaction of SnII on goethite (α-FeOOH): surface complexation, redox reaction, reductive dissolution, and phase transformation.

PubMed

Dulnee, Siriwan; Scheinost, Andreas C

2014-08-19

To elucidate the potential risk of (126)Sn migration from nuclear waste repositories, we investigated the surface reactions of Sn(II) on goethite as a function of pH and Sn(II) loading under anoxic condition with O2 level < 2 ppmv. Tin redox state and surface structure were investigated by Sn K edge X-ray absorption spectroscopy (XAS), goethite phase transformations were investigated by high-resolution transmission electron microscopy and selected area electron diffraction. The results demonstrate the rapid and complete oxidation of Sn(II) by goethite and formation of Sn(IV) (1)E and (2)C surface complexes. The contribution of (2)C complexes increases with Sn loading. The Sn(II) oxidation leads to a quantitative release of Fe(II) from goethite at low pH, and to the precipitation of magnetite at higher pH. To predict Sn sorption, we applied surface complexation modeling using the charge distribution multisite complexation approach and the XAS-derived surface complexes. Log K values of 15.5 ± 1.4 for the (1)E complex and 19.2 ± 0.6 for the (2)C complex consistently predict Sn sorption across pH 2-12 and for two different Sn loadings and confirm the strong retention of Sn(II) even under anoxic conditions.

Pechini process-derived tin oxide and tin oxide-graphite composites for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Zhang, R.; Lee, Jim Y.; Liu, Z. L.

The Pechini process [Ceram. Bull. 68 (1989) 1002] is used to obtain fine tin oxide powders that reduce the specific volume change in Li + insertion and extraction reactions. The suitability of these tin oxides as active materials for negative electrodes in lithium-ion batteries is investigated. From elemental analysis, it is found that the templating polymer network is almost completely obliterated after heating at 500 °C. The best tin oxide does not exhibit extensive crystallization of tin atoms even after 30 cycles of alloying and de-alloying reactions with Li. The structure and the specific capacity of the oxides are dependent on the heat treatment and remnants of the polymeric CH network can impose an unfavorable outcome. A capacity of 600 mAh g -1, which is unchanged for 30 cycles, can be obtained from tin oxide heat treated at 1000 °C. Composites of graphite and SnO 2 are also prepared and exhibit synergistic interactions between graphite and tin oxide which are similar to those reported previously [Electrochem. Solid State Lett. 3 (2000) 167].

Infrared Emissivity of Tin upon Release of a 25 GPa Shock into a LiF Window

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turley, W. D., Holtkamp, D. B., Marshall, B. R., Stevens, G. D., Veeser, L. R.

We measured the emissivity of a tin sample at its interface with a lithium-fluoride window upon release of a 25 GPa shock wave from the tin into the window. Measurements were made over four wavelength bands between 1.2 and 5.4 μm. Thermal emission backgrounds from the tin, glue, and lithium fluoride were successfully removed from the reflectance signals. Emissivity changes for the sample, which was initially nearly specular, were small except for the longest wavelength band, where uncertainties were high because of poor signal-to-noise ratio at that wavelength. A thin glue layer, which bonds the sample to the window, wasmore » found to heat from reverberations of the shock wave between the tin and the lithium fluoride. At approximately 3.4 μm the thermal emission from the glue was large compared to the tin, allowing a good estimate of the glue temperature from the thermal radiance. The glue appears to remain slightly colder than the tin, thereby minimizing heat conduction into or out of the tin immediately after the shock passage.« less

Ternary and coupled binary zinc tin oxide nanopowders: Synthesis, characterization, and potential application in photocatalytic processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ivetić, T.B., E-mail: tamara.ivetic@df.uns.ac.rs; Finčur, N.L.; Đačanin, Lj. R.

2015-02-15

Highlights: • Mechanochemically synthesized nanocrystalline zinc tin oxide (ZTO) powders. • Photocatalytic degradation of alprazolam in the presence of ZTO water suspensions. • Coupled binary ZTO exhibits enhanced photocatalytic activity compared to ternary ZTO. - Abstract: In this paper, ternary and coupled binary zinc tin oxide nanocrystalline powders were prepared via simple solid-state mechanochemical method. X-ray diffraction, scanning electron microscopy, Raman and reflectance spectroscopy were used to study the structure and optical properties of the obtained powder samples. The thermal behavior of zinc tin oxide system was examined through simultaneous thermogravimetric-differential scanning calorimetric analysis. The efficiencies of ternary (Zn{sub 2}SnO{submore » 4} and ZnSnO{sub 3}) and coupled binary (ZnO/SnO{sub 2}) zinc tin oxide water suspensions in the photocatalytic degradation of alprazolam, short-acting anxiolytic of the benzodiazepine class of psychoactive drugs, under UV irradiation were determined and compared with the efficiency of pure ZnO and SnO{sub 2}.« less

Azole Functionalized Polyoxo-Titanium Clusters with Sunlight-Driven Dye Degradation Applications: Synthesis, Structure, and Photocatalytic Studies.

PubMed

Narayanam, Nagaraju; Chintakrinda, Kalpana; Fang, Wei-Hui; Kang, Yao; Zhang, Lei; Zhang, Jian

2016-10-06

Six polyoxo-titanium clusters (PTCs) with varying nuclearities containing Ti-N bonds and heteronuclearity, namely, [Ti 6 (μ 3 -O) 2 (μ 2 -O) 2 (O 3 P-Phen) 2 (OiPr) 10 (1-hbta) 2 ] (PTC-37), Ti 8 (μ 3 -O) 2 (μ 2 -O) 2 (O 3 P-Phen) 2 (OiPr) 16 (adn) 2 (NO 3 ) 2 ] (PTC-38), [Ti 4 (μ 3 -O)(μ 2 -O)(μ 2 -OiPr) 2 (OiPr) 4 (O 3 P-Phen) 3 (1,10-phn)](HOiPr) (PTC-39), [Ti 4 (μ 3 -O)(μ 2 -OiPr) 3 (OiPr) 5 (O 3 P-Phen) 3 (Im)] (PTC-40), [Ti 4 (μ 3 -O)(μ 2 -OiPr) 3 (OiPr) 5 (O 3 P-Phen) 3 (Im)][Ti 3 M(μ 3 -O)(μ 2 -OiPr) 3 (OiPr) 3 (O 3 P-Phen) 3 (Im)] (M = Co for PTC-41 and M = Zn for PTC-42; O 3 P-Phen = phenyl phosphonate, 1-hbta = 1-hydroxy benzotriazolate, adn = adenine, 1,10-phn = 1,10-phenanthroline, Im = imidazolate, and OiPr = isopropoxide) were prepared as crystalline samples and structurally characterized. Simultaneous doping of nitrogen and transition metal heteroatoms into the Ti-O clusters created complex chemical environments in the resulting hybrid materials. Thus, photocatalytic methylene blue degradation studies were performed to understand structure-property relationships in these Ti cluster-based materials. The complex chemical environment created in these novel molecular clusters had proved to exhibit ligand-dependent photocatalytic activities under normal sunlight. Adenine-functionalized PTC-38 presented moderate activities, while other PTCs all show rapid dye degradation.

Fabrication of Highly Ordered and Well-Aligned PbTiO 3/TiN Core–Shell Nanotube Arrays

DOE PAGES

Yoon, Jaesung; Kim, Sangjoon; Kim, Dongjin; ...

2015-04-30

Highly ordered and well-aligned PbTiO 3/TiN core–shell nanotubes are fabricated in this paper via an anodic aluminum oxide templating route followed by TiN and TiO 2 atomic layer deposition deposition and a subsequent PbO vapor reaction. Finally, PbTiO 3/TiN nanotubes keep their original shape after the vapor phase reaction, and they display well-defined piezoresponse hysteresis curves with remnant piezoresponse of 38 pm V -1.

Electrical Properties and Manufacturability of ITO-MgF2 and Related Transparent Arcproof Spacecraft Coatings

NASA Technical Reports Server (NTRS)

Hambourger, Paul D.

2003-01-01

To investigate the applicability of co-deposited indium tin oxide and magnesium fluoride as a transparent arcproof coating on the exterior of PowerSphere microsatellites. This included testing coating performance after deposition on flexible polymeric substrates, determining whether ultraviolet (UV) radiation present during deposition might affect the UV-curing resin contained in the substrate, and preparation of coated polymeric samples for radiation damage studies by the PowerSphere team.

Multiple domains of fission yeast Cdc19p (MCM2) are required for its association with the core MCM complex.

PubMed

Sherman, D A; Pasion, S G; Forsburg, S L

1998-07-01

The members of the MCM protein family are essential eukaryotic DNA replication factors that form a six-member protein complex. In this study, we use antibodies to four MCM proteins to investigate the structure of and requirements for the formation of fission yeast MCM complexes in vivo, with particular regard to Cdc19p (MCM2). Gel filtration analysis shows that the MCM protein complexes are unstable and can be broken down to subcomplexes. Using coimmunoprecipitation, we find that Mis5p (MCM6) and Cdc21p (MCM4) are tightly associated with one another in a core complex with which Cdc19p loosely associates. Assembly of Cdc19p with the core depends upon Cdc21p. Interestingly, there is no obvious change in Cdc19p-containing MCM complexes through the cell cycle. Using a panel of Cdc19p mutants, we find that multiple domains of Cdc19p are required for MCM binding. These studies indicate that MCM complexes in fission yeast have distinct substructures, which may be relevant for function.

Multiple Domains of Fission Yeast Cdc19p (MCM2) Are Required for Its Association with the Core MCM Complex

PubMed Central

Sherman, Daniel A.; Pasion, Sally G.; Forsburg, Susan L.

1998-01-01

The members of the MCM protein family are essential eukaryotic DNA replication factors that form a six-member protein complex. In this study, we use antibodies to four MCM proteins to investigate the structure of and requirements for the formation of fission yeast MCM complexes in vivo, with particular regard to Cdc19p (MCM2). Gel filtration analysis shows that the MCM protein complexes are unstable and can be broken down to subcomplexes. Using coimmunoprecipitation, we find that Mis5p (MCM6) and Cdc21p (MCM4) are tightly associated with one another in a core complex with which Cdc19p loosely associates. Assembly of Cdc19p with the core depends upon Cdc21p. Interestingly, there is no obvious change in Cdc19p-containing MCM complexes through the cell cycle. Using a panel of Cdc19p mutants, we find that multiple domains of Cdc19p are required for MCM binding. These studies indicate that MCM complexes in fission yeast have distinct substructures, which may be relevant for function. PMID:9658174

Pressure-Stabilized Tin Selenide Phase with an Unexpected Stoichiometry and a Predicted Superconducting State at Low Temperatures

NASA Astrophysics Data System (ADS)

Yu, Hulei; Lao, Wenxin; Wang, Lijuan; Li, Kuo; Chen, Yue

2017-03-01

Tin-selenium binary compounds are important semiconductors that have attracted much interest for thermoelectric and photovoltaic applications. As tin has a +2 or +4 oxidation state and selenium has an oxidation number of -2 , only SnSe and SnSe2 have been observed. In this work, we show that the chemical bonding between tin and selenium becomes counterintuitive under pressures. Combining evolutionary algorithms and density functional theory, a novel cubic tin-selenium compound with an unexpected stoichiometry 3 ∶4 has been predicted and further synthesized in laser-heated diamond anvil cell experiments. Different from the conventional SnSe and SnSe2 semiconductors, Sn3 Se4 is predicted to be metallic and exhibit a superconducting transition at low temperatures. Based on electron density and Bader charge analysis, we show that Sn3 Se4 has a mixed nature of chemical bonds. The successful synthesis of Sn3 Se4 paves the way for the discovery of other IV-VI compounds with nonconventional stoichiometries and novel properties.

Pressure-Stabilized Tin Selenide Phase with an Unexpected Stoichiometry and a Predicted Superconducting State at Low Temperatures.

PubMed

Yu, Hulei; Lao, Wenxin; Wang, Lijuan; Li, Kuo; Chen, Yue

2017-03-31

Tin-selenium binary compounds are important semiconductors that have attracted much interest for thermoelectric and photovoltaic applications. As tin has a +2 or +4 oxidation state and selenium has an oxidation number of -2, only SnSe and SnSe_{2} have been observed. In this work, we show that the chemical bonding between tin and selenium becomes counterintuitive under pressures. Combining evolutionary algorithms and density functional theory, a novel cubic tin-selenium compound with an unexpected stoichiometry 3∶4 has been predicted and further synthesized in laser-heated diamond anvil cell experiments. Different from the conventional SnSe and SnSe_{2} semiconductors, Sn_{3}Se_{4} is predicted to be metallic and exhibit a superconducting transition at low temperatures. Based on electron density and Bader charge analysis, we show that Sn_{3}Se_{4} has a mixed nature of chemical bonds. The successful synthesis of Sn_{3}Se_{4} paves the way for the discovery of other IV-VI compounds with nonconventional stoichiometries and novel properties.

Triazolylidene-Iridium Complexes with a Pendant Pyridyl Group for Cooperative Metal-Ligand Induced Catalytic Dehydrogenation of Amines.

PubMed

Valencia, Marta; Pereira, Ana; Müller-Bunz, Helge; Belderraín, Tomás R; Pérez, Pedro J; Albrecht, Martin

2017-07-03

Two iridium(III) complexes containing a C,N-bidentate pyridyl-triazolylidene ligand were prepared that are structurally very similar but differ in their pendant substituent. Whereas complex 1 contains a non-coordinating pyridyl unit, complex 2 has a phenyl group on the triazolylidene substituent. The presence of the basic pyridyl unit has distinct effects on the catalytic activity of the complex in the oxidative dehydrogenation of benzylic amines, inducing generally higher rates, higher selectivity towards formation of imines versus secondary amines, and notable quantities of tertiary amines when compared to the phenyl-functionalized analogue. The role of the pyridyl functionality has been elucidated from a set of stoichiometric experiments, which demonstrate hydrogen bonding between the pendant pyridyl unit and the amine protons of the substrate. Such N pyr ⋅⋅⋅H-N interactions are demonstrated by X-ray diffraction analysis, 1 H NMR, and IR spectroscopy, and suggest a pathway of substrate bond-activation that involves concerted substrate binding through the Lewis acidic iridium center and the Lewis basic pyridyl site appended to the triazolylidene ligand, in agreement with ligand-metal cooperative substrate activation. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

40 CFR 421.292 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... CATEGORY Secondary Tin Subcategory § 421.292 Effluent limitations guidelines representing the degree of... attainable by the application of the best practicable technology currently available: (a) Tin smelter SO2 scrubber. BPT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any...

40 CFR 421.292 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... CATEGORY Secondary Tin Subcategory § 421.292 Effluent limitations guidelines representing the degree of... attainable by the application of the best practicable technology currently available: (a) Tin smelter SO2 scrubber. BPT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any...

40 CFR 421.293 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Tin Subcategory § 421.293 Effluent limitations guidelines representing the degree of effluent... application of the best available technology economically achievable: (a) Tin smelter SO2 scrubber. BAT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum...

40 CFR 421.293 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... Tin Subcategory § 421.293 Effluent limitations guidelines representing the degree of effluent... application of the best available technology economically achievable: (a) Tin smelter SO2 scrubber. BAT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum...

40 CFR 421.292 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... CATEGORY Secondary Tin Subcategory § 421.292 Effluent limitations guidelines representing the degree of... attainable by the application of the best practicable technology currently available: (a) Tin smelter SO2 scrubber. BPT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any...

40 CFR 421.292 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2010 CFR

2010-07-01

... CATEGORY Secondary Tin Subcategory § 421.292 Effluent limitations guidelines representing the degree of... attainable by the application of the best practicable technology currently available: (a) Tin smelter SO2 scrubber. BPT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any...

40 CFR 421.293 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2012 CFR

2012-07-01

... Tin Subcategory § 421.293 Effluent limitations guidelines representing the degree of effluent... application of the best available technology economically achievable: (a) Tin smelter SO2 scrubber. BAT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum...

40 CFR 421.293 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2014 CFR

2014-07-01

... Tin Subcategory § 421.293 Effluent limitations guidelines representing the degree of effluent... application of the best available technology economically achievable: (a) Tin smelter SO2 scrubber. BAT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum...

40 CFR 421.292 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2013 CFR

2013-07-01

... CATEGORY Secondary Tin Subcategory § 421.292 Effluent limitations guidelines representing the degree of... attainable by the application of the best practicable technology currently available: (a) Tin smelter SO2 scrubber. BPT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any...

40 CFR 421.293 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Tin Subcategory § 421.293 Effluent limitations guidelines representing the degree of effluent... application of the best available technology economically achievable: (a) Tin smelter SO2 scrubber. BAT Limitations for the Secondary Tin Subcategory Pollutant or pollutant property Maximum for any 1 day Maximum...

Valence-band offsets in strained SiGeSn/Si layers with different tin contents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bloshkin, A. A., E-mail: bloshkin@isp.nsc.ru; Yakimov, A. I.; Timofeev, V. A.

Admittance spectroscopy is used to study hole states in Si{sub 0.7–y}Ge{sub 0.3}Sn{sub y}/Si quantum wells in the tin content range y = 0.04–0.1. It is found that the hole binding energy increases with tin content. The hole size-quantization energies in structures containing a pseudomorphic Si{sub 0.7–y}Ge{sub 0.3}Sn{sub y} layer in the Si matrix are determined using the 6-band kp method. The valence-band offset at the Si{sub 0.7–y}Ge{sub 0.3}Sn{sub y} heterointerface is determined by combining the numerical calculation results and experimental data. It is found that the dependence of the experimental values of the valence-band offsets between pseudomorphic Si{sub 0.7–y}Ge{sub 0.3}Sn{submore » y} layers and Si on the tin content is described by the expression ΔE{sub V}{sup exp} = (0.21 ± 0.01) + (3.35 ± 7.8 × 10{sup –4})y eV.« less

Effect of Si in reactively sputtered Ti-Si-N films on structure and diffusion barrier performance

NASA Astrophysics Data System (ADS)

Sun, X.; Kolawa, E.; Im, S.; Garland, C.; Nicolet, M.-A.

Two ternary films about 100 nm thick, Ti34Si23N43 (b3) and Ti35Si13N52 (c3), are synthesized by reactively sputtering a Ti5Si3 or a Ti3Si target, respectively. The silicon-lean film (c3) has a columnar structure closely resembling that of TiN. As a diffusion barrier between a shallow Si n+p junction diode and a Cu overlayer, this material is effective up to 700 °C for 30 min annealing in vacuum, a performance similar to that for TiN. The silicon-rich (b3) film contains nanocrystals of TiN, randomly oriented and embedded in an amorphous matrix. A film of (b3) maintains the stability of the same diode structure up to 850 °C for 30 min in vacuum. This film (b3) is clearly superior to TiN or to (c3). Similar experiments performed with Al instead of Cu overlayers highlight the importance of the thermodynamic stability of a barrier layer and demonstrate convincingly that for stable barriers the microstructure is a parameter that directly determines the barrier performance.

Release Path Temperatures of Shock-Compressed Tin from Dynamic Reflectance and Radiance Measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

La Lone, B. M.; Stevens, G. D.; Turley, W. D.

2013-08-01

Dynamic reflectance and radiance measurements were conducted for tin samples shock compressed to 35 GPa and released to 15 GPa using high explosives. We determined the reflectance of the tin samples glued to lithium fluoride windows using an integrating sphere with an internal xenon flashlamp as an illumination source. The dynamic reflectance (R) was determined at near normal incidence in four spectral bands with coverage in visible and near-infrared spectra. Uncertainties in R/R0 are < 2%, and uncertainties in absolute reflectance are < 5%. In complementary experiments, thermal radiance from the tin/glue/lithium fluoride interface was recorded with similar shock stressmore » and spectral coverage as the reflectance measurements. The two sets of experiments were combined to obtain the temperature history of the tin surface with an uncertainty of < 2%. The stress at the interface was determined from photonic Doppler velocimetry and combined with the temperatures to obtain temperature-stress release paths for tin. We discuss the relationship between the experimental release paths and release isentropes that begin on the principal shock Hugoniot.« less

Poly (p-phenyleneneacetylene) light-emitting diodes

DOEpatents

Shinar, Joseph; Swanson, Leland S.; Lu, Feng; Ding, Yiwei; Barton, Thomas J.; Vardeny, Zeev V.

1994-10-04

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes.

Poly (p-phenyleneacetylene) light-emitting diodes

DOEpatents

Shinar, J.; Swanson, L.S.; Lu, F.; Ding, Y.; Barton, T.J.; Vardeny, Z.V.

1994-10-04

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes. 8 figs.

Fabrication of poly(p-phenyleneacetylene) light-emitting diodes

DOEpatents

Shinar, J.; Swanson, L.S.; Lu, F.; Ding, Y.

1994-08-02

Acetylene-containing poly(p-phenyleneacetylene) (PPA)-based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as Al or Al/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes. 8 figs.

Fabrication of poly(p-phenyleneacetylene) light-emitting diodes

DOEpatents

Shinar, Joseph; Swanson, Leland S.; Lu, Feng; Ding, Yiwei

1994-08-02

Acetylene containing poly(p-phenyleneacetylene) (PPA) - based light-emitting diodes (LEDs) are provided. The LEDs are fabricated by coating a hole-injecting electrode, preferably an indium tin oxide (ITO) coated glass substrate, with a PPA polymer, such as a 2,5-dibutoxy or a 2,5-dihexoxy derivative of PPA, dissolved in an organic solvent. This is then followed by evaporating a layer of material capable of injecting electrons, such as A1 or A1/Ca, onto the polymer to form a base electrode. This composition is then annealed to form efficient EL diodes.

Synthesis and Characterization of Graphene/ITO Nanoparticle Hybrid Transparent Conducting Electrode

NASA Astrophysics Data System (ADS)

Hemasiri, Bastian Waduge Naveen Harindu; Kim, Jae-Kwan; Lee, Ji-Myon

2018-03-01

The combination of graphene with conductive nanoparticles, forming graphene-nanoparticle hybrid materials, offers a number of excellent properties for advanced engineering applications. A novel and simple method was developed to deposit 10 wt% tin-doped indium tin oxide (ITO) nanoparticles on graphene. The method involved a combination of a solution-based environmentally friendly electroless deposition approach and subsequent vacuum annealing. A stable organic-free solution of ITO was prepared from economical salts of In(NO3) 3 · H2O and SnCl4. The obtained ITO nanostructure exhibited a unique architecture, with uniformly dispersed 25-35 nm size ITO nanoparticles, containing only the crystallized In2O3 phase. The synthesized ITO nanoparticles-graphene hybrid exhibited very good and reproducible optical transparency in the visible range (more than 85%) and a 28.2% improvement in electrical conductivity relative to graphene synthesized by chemical vapor deposition. It was observed that the ITO nanoparticles affect the position of the Raman signal of graphene, in which the D, G, and 2D peaks were redshifted by 5.65, 5.69, and 9.74 cm-1, respectively, and the annealing conditions had no significant effect on the Raman signatures of graphene. [Figure not available: see fulltext.

Effect of doping of tin on optoelectronic properties of indium oxide: DFT study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tripathi, Madhvendra Nath, E-mail: ommadhav27@gmail.com

2015-06-24

Indium tin oxide is widely used transparent conductor. Experimentally observed that 6% tin doping in indium oxide is suitable for optoelectronic applications and more doping beyond this limit degrades the optoelectronic property. The stoichiometry (In{sub 32-x}Sn{sub x}O{sub 48+x/2}; x=0-6) is taken to understand the change in lattice parameter, electronic structure, and optical property of ITO. It is observed that lattice parameter increases and becomes constant after 6% tin doping that is in good agreement of the experimental observation. The electronic structure calculation shows that the high tin doping in indium oxide adversely affects the dispersive nature of the bottom ofmore » conduction band of pure indium oxide and decreases the carrier mobility. Optical calculations show that transmittance goes down upto 60% for the tin concentration more than 6%. The present paper shows that how more than 6% tin doping in indium oxide adversely affects the optoelectronic property of ITO.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rohwer, Lauren E. S.; Martin, James E.

In this study, reliable methods for tin whisker mitigation are needed for applications that utilize tin-plated commercial components. Tin can grow whiskers that can lead to electrical shorting, possibly causing critical systems to fail catastrophically. The mechanisms of tin whisker growth are unclear and this makes prediction of the lifetimes of critical components uncertain. The development of robust methods for tin whisker mitigation is currently the best approach to eliminating the risk of shorting. Current mitigation methods are based on unfilled polymer coatings that are not impenetrable to tin whiskers. In this paper we report tin whisker mitigation results formore » several filled polymer coatings. The whisker-penetration resistance of the coatings was evaluated at elevated temperature and high humidity and under temperature cycling conditions. The composite coatings comprised Ni and MgF 2-coated Al/Ni/Al platelets in epoxy resin or silicone rubber. In addition to improved whisker mitigation, these platelet composites have enhanced thermal conductivity and dielectric constant compared with unfilled polymers.« less

Domain mapping of the Rad51 paralog protein complexes

PubMed Central

Miller, Kristi A.; Sawicka, Dorota; Barsky, Daniel; Albala, Joanna S.

2004-01-01

The five human Rad51 paralogs are suggested to play an important role in the maintenance of genome stability through their function in DNA double-strand break repair. These proteins have been found to form two distinct complexes in vivo, Rad51B–Rad51C–Rad51D–Xrcc2 (BCDX2) and Rad51C–Xrcc3 (CX3). Based on the recent Pyrococcus furiosus Rad51 structure, we have used homology modeling to design deletion mutants of the Rad51 paralogs. The models of the human Rad51B, Rad51C, Xrcc3 and murine Rad51D (mRad51D) proteins reveal distinct N-terminal and C-terminal domains connected by a linker region. Using yeast two-hybrid and co-immunoprecipitation techniques, we have demonstrated that a fragment of Rad51B containing amino acid residues 1–75 interacts with the C-terminus and linker of Rad51C, residues 79–376, and this region of Rad51C also interacts with mRad51D and Xrcc3. We have also determined that the N-terminal domain of mRad51D, residues 4–77, binds to Xrcc2 while the C-terminal domain of mRad51D, residues 77–328, binds Rad51C. By this, we have identified the binding domains of the BCDX2 and CX3 complexes to further characterize the interaction of these proteins and propose a scheme for the three-dimensional architecture of the BCDX2 and CX3 paralog complexes. PMID:14704354

Plasma enhanced chemical vapor deposition of titanium nitride thin films using cyclopentadienyl cycloheptatrienyl titanium

NASA Astrophysics Data System (ADS)

Charatan, R. M.; Gross, M. E.; Eaglesham, D. J.

1994-10-01

The use of a low oxidation state Ti compound, cyclopentadienyl cycloheptatrienyl titanium, (C5H5) Ti(C7H7) (CPCHT), as a potential source for TiN and Ti in plasma enhanced chemical vapor deposition processes has been investigated. This precursor provides us with a new chemical vapor deposition route to TiN films that offer an interesting contrast to films deposited from Ti(IV) precursors. Film depositions were carried out by introducing CPCHT, with H2 carrier gas, into the downstream region of a NH3, N2, H2, or mixed H2/N2 plasma. Low resistivity (100-250 micro-ohm cm) nitrogen-rich TiN films with little carbon or oxygen incorporation and good conformality were deposited with activated N2 or NH3 at deposition temperatures of 300-600 C, inclusive. Mixed H2/N2 plasmas resulted in more stoichiometric TiN films with similar properties. The most striking feature of these films is the absence of columnar grain growth, in contrast to TiN films deposited using TiCl4 or Ti(NR(2))(4). Although the film texture was influenced by the plasma gas, the average grain size of the films deposited using activated N2 and NH3 was similar. The TiN films that we deposited were effective diffusion barriers between aluminum and silicon up to 575 C. Depositions using activated H2 resulted in films with significantly less carbon than CPCHT, but still having a minimum of 2.7:1 C:Ti. The lower oxidation state of the precursor did not facilitate the deposition of a Ti-rich film. No depositions were observed with any of the reactant gases in the absence of plasmas activation.

Determination of trace amounts of tin in geological materials by atomic absorption spectrometry

USGS Publications Warehouse

Welsch, E.P.; Chao, T.T.

1976-01-01

An atomic absorption method is described for the determination of traces of tin in rocks, soils, and stream sediments. A dried mixture of the sample and ammonium iodide is heated to volatilize tin tetraiodide -which is then dissolved in 5 % hydrochloric acid, extracted into TOPO-MIBK, and aspirated into a nitrous oxide-acetylene flame. The limit of determination is 2 p.p.m. tin and the relative standard deviation ranges from 2 to 14 %. Up to 20 % iron and 1000 p.p.m. Cu, Pb, Zn, Mn, Hg, Mo, V, or W in the sample do not interfere. As many as 50 samples can be easily analyzed per man-day. ?? 1976.

Effect of tin oxide nanoparticle binding on the structure and activity of α-amylase from Bacillus amyloliquefaciens

NASA Astrophysics Data System (ADS)

Jahir Khan, Mohammad; Qayyum, Shariq; Alam, Fahad; Husain, Qayyum

2011-11-01

Proteins adsorbed on nanoparticles (NPs) are being used in biotechnology, biosensors and drug delivery. However, understanding the effect of NPs on the structure of proteins is still in a nascent state. In the present paper tin oxide (SnO2) NPs were synthesized by the reaction of SnCl4·5H2O in methanol via the sol-gel method and characterized by x-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR) and transmission electron microscopy (TEM). The binding of these SnO2-NPs with α-amylase was investigated by using UV-vis, fluorescence and circular dichroism (CD) spectroscopic techniques. A strong quenching of tryptophan fluorescence intensity in α-amylase was observed due to formation of a ground state complex with SnO2-NPs. Far-UV CD spectra showed that the secondary structure of α-amylase was changed in the presence of NPs. The Michaelis-Menten constant (Km), was found to be 26.96 and 28.45 mg ml - 1, while Vmax was 4.173 and 3.116 mg ml - 1 min - 1 for free and NP-bound enzyme, respectively.

Effect of pretreatment on a platinized tin oxide catalyst used for low-temperature CO-oxidation

NASA Technical Reports Server (NTRS)

Drawdy, Jean E.; Hoflund, Gar B.; Gardner, Steven D.; Yngvadottir, Eva; Schryer, David R.

1990-01-01

A commercial platinized tin oxide catalyst used for low-temperature CO oxidation has been characterized using ion scattering spectroscopy (ISS), Auger electron spectroscopy (AES) and Electron Spectroscopy for Chemical Analysis (ESCA) before and after reduction in 40 Torr of CO for 1 hour at various temperatures from 75 to 175 C. The reduction results in loss of surface oxygen, formation of metallic tin, conversion of platinum oxides to Pt-O-Sn and Pt(OH)2 and a small amount of metallic Pt which alloys with the tin. These results should be useful in understanding how the pretreatment temperature affects the catalytic activity of platinized tin oxide toward CO oxidation.

Influence of essential onion oil on tin and chromium dissolution from tinplate.

PubMed

Nincević Grassino, A; Grabarić, Z; Pezzani, A; Fasanaro, G; Lo Voi, A

2009-07-01

During food and beverage packaging in tinplate cans the dissolution of tin and chromium into food content may occur. To protect metallic surface different corrosion inhibitors are recommended, nowadays particularly a new group of natural products is of interest. In this work the influence of essential onion oil (EOO) on metals dissolution (tin and chromium) from tinplate sheets before food canning was investigated. The analyses were performed by galvanostatic method and atomic absorption spectroscopy. The values of tin obtained for the internal surface of tinplate covered with EOO (7.31-9.76 gm(-2)) are lower than the values when dioctyl sebacate oil (DOS), as a protective tinplate surface layer for food caning, was used (9.24-11.03 gm(-2)). Obviously, the presence of EOO diminished more efficiently then DOS oil the dissolution of tin in electrolyte during galvanostatic analyses. The efficiency of EOO as corrosion inhibitor was even more pronounced in the case of chromium where the dissolution from 1.8-2.5 mgm(-2) (DOS oil) was lowered to 1.0-1.3 mgm(-2) (EOO). Correlation of results obtained with two different physico-chemical methods was satisfying.

2ND FLOOR HALLWAY LOOKING EAST, NOTE PRESSED TIN CEILING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2ND FLOOR HALLWAY LOOKING EAST, NOTE PRESSED TIN CEILING - New York State Soldiers & Sailors Home, Building No. 29, Department of Veterans Affairs Medical Center, 76 Veterans Avenue, Bath, Steuben County, NY

Tumor-infiltrating Neutrophils is Prognostic and Predictive for Postoperative Adjuvant Chemotherapy Benefit in Patients With Gastric Cancer.

PubMed

Zhang, Heng; Liu, Hao; Shen, Zhenbin; Lin, Chao; Wang, Xuefei; Qin, Jing; Qin, Xinyu; Xu, Jiejie; Sun, Yihong

2018-02-01

This study was aimed to investigate the prognostic value of tumor-infiltrating neutrophils (TINs) and to generate a predictive model to refine postoperative risk stratification system for patients with gastric cancer. TIN presents in various malignant tumors, but its clinical significance in gastric cancer remains obscure. The study enrolled 3 independent sets of patients with gastric cancer from 2 institutional medical centers of China. TIN was estimated by immunohistochemical staining of CD66b, and its relationship with clinicopathological features and clinical outcomes were evaluated. Prognostic accuracies were evaluated by C-index and Akaike information criterion. TINs in gastric cancer tissues ranged from 0 to 192 cells/high magnification filed (HPF), 0 to 117 cells/HPF, and 0 to 142 cells/HPF in the training, testing, and validation sets, respectively. TINs were negatively correlated with lymph node classification (P = 0.007, P = 0.041, and P = 0.032, respectively) and tumor stage (P = 0.019, P = 0.013, and P = 0.025, respectively) in the 3 sets. Moreover, multivariate analysis identified TINs and tumor node metastasis (TNM) stage as 2 independent prognostic factors for overall survival. Incorporation of TINs into well-established TNM system generated a predictive model that shows better predictive accuracy for overall survival. More importantly, patients with higher TINs were prone to overall survival benefit from postoperative adjuvant chemotherapy. These results were validated in the independent testing and validation sets. TIN in gastric cancer was identified as an independent prognostic factor, which could be incorporated into standard TNM staging system to refine risk stratification and predict for overall survival benefit from postoperative chemotherapy in patients with gastric cancer.

Shape Engineering Driven by Selective Growth of SnO2 on Doped Ga2O3 Nanowires.

PubMed

Alonso-Orts, Manuel; Sánchez, Ana M; Hindmarsh, Steven A; López, Iñaki; Nogales, Emilio; Piqueras, Javier; Méndez, Bianchi

2017-01-11

Tailoring the shape of complex nanostructures requires control of the growth process. In this work, we report on the selective growth of nanostructured tin oxide on gallium oxide nanowires leading to the formation of SnO 2 /Ga 2 O 3 complex nanostructures. Ga 2 O 3 nanowires decorated with either crossing SnO 2 nanowires or SnO 2 particles have been obtained in a single step treatment by thermal evaporation. The reason for this dual behavior is related to the growth direction of trunk Ga 2 O 3 nanowires. Ga 2 O 3 nanowires grown along the [001] direction favor the formation of crossing SnO 2 nanowires. Alternatively, SnO 2 forms rhombohedral particles on [110] Ga 2 O 3 nanowires leading to skewer-like structures. These complex oxide structures were grown by a catalyst-free vapor-solid process. When pure Ga and tin oxide were used as source materials and compacted powders of Ga 2 O 3 acted as substrates, [110] Ga 2 O 3 nanowires grow preferentially. High-resolution transmission electron microscopy analysis reveals epitaxial relationship lattice matching between the Ga 2 O 3 axis and SnO 2 particles, forming skewer-like structures. The addition of chromium oxide to the source materials modifies the growth direction of the trunk Ga 2 O 3 nanowires, growing along the [001], with crossing SnO 2 wires. The SnO 2 /Ga 2 O 3 junctions does not meet the lattice matching condition, forming a grain boundary. The electronic and optical properties have been studied by XPS and CL with high spatial resolution, enabling us to get both local chemical and electronic information on the surface in both type of structures. The results will allow tuning optical and electronic properties of oxide complex nanostructures locally as a function of the orientation. In particular, we report a dependence of the visible CL emission of SnO 2 on its particular shape. Orange emission dominates in SnO 2 /Ga 2 O 3 crossing wires while green-blue emission is observed in SnO 2 particles attached to Ga 2 O 3 trunks. The results show that the Ga 2 O 3 -SnO 2 system appears to be a benchmark for shape engineering to get architectures involving nanowires via the control of the growth direction of the nanowires.

Recycling at Camp.

ERIC Educational Resources Information Center

Cummins, William M.

1988-01-01

Outlines a Michigan summer camp's efforts to reduce solid waste disposal by recycling cardboard, tin, glass, aluminum, and plastic milk containers. Points out variables affecting the success of such efforts. Discusses Michigan state funding for the development of recycling programs. (SV)

Transcriptome-wide identification of RNA-binding protein and microRNA target sites by PAR-CLIP

PubMed Central

Hafner, Markus; Landthaler, Markus; Burger, Lukas; Khorshid, Mohsen; Hausser, Jean; Berninger, Philipp; Rothballer, Andrea; Ascano, Manuel; Jungkamp, Anna-Carina; Munschauer, Mathias; Ulrich, Alexander; Wardle, Greg S.; Dewell, Scott; Zavolan, Mihaela; Tuschl, Thomas

2010-01-01

Summary RNA transcripts are subject to post-transcriptional gene regulation involving hundreds of RNA-binding proteins (RBPs) and microRNA-containing ribonucleoprotein complexes (miRNPs) expressed in a cell-type dependent fashion. We developed a cell-based crosslinking approach to determine at high resolution and transcriptome-wide the binding sites of cellular RBPs and miRNPs. The crosslinked sites are revealed by thymidine to cytidine transitions in the cDNAs prepared from immunopurified RNPs of 4-thiouridine-treated cells. We determined the binding sites and regulatory consequences for several intensely studied RBPs and miRNPs, including PUM2, QKI, IGF2BP1-3, AGO/EIF2C1-4 and TNRC6A-C. Our study revealed that these factors bind thousands of sites containing defined sequence motifs and have distinct preferences for exonic versus intronic or coding versus untranslated transcript regions. The precise mapping of binding sites across the transcriptome will be critical to the interpretation of the rapidly emerging data on genetic variation between individuals and how these variations contribute to complex genetic diseases. PMID:20371350