Gas turbine engine with supersonic compressor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, II, William Byron; Lawlor, Shawn P.

A gas turbine engine having a compressor section using blades on a rotor to deliver a gas at supersonic conditions to a stator. The stator includes one or more of aerodynamic ducts that have converging and diverging portions for deceleration of the gas to subsonic conditions and to deliver a high pressure gas to combustors. The aerodynamic ducts include structures for changing the effective contraction ratio to enable starting even when designed for high pressure ratios, and structures for boundary layer control. In an embodiment, aerodynamic ducts are provided having an aspect ratio of two to one (2:1) or more,more » when viewed in cross-section orthogonal to flow direction at an entrance to the aerodynamic duct.« less

Atomizing nozzle and method

DOEpatents

Ting, Jason; Anderson, Iver E.; Terpstra, Robert L.

2000-03-16

A high pressure close-coupled gas atomizing nozzle includes multiple discrete gas jet discharge orifices having aerodynamically designed convergent-divergent geometry with an first converging section communicated to a gas supply manifold and to a diverging section by a constricted throat section to increase atomizing gas velocity. The gas jet orifices are oriented at gas jet apex angle selected relative to the melt supply tip apex angle to establish a melt aspiration condition at the melt supply tip.

Refined methods of aeroelastic analysis and optimization. [swept wings, propeller theory, and subsonic flutter

NASA Technical Reports Server (NTRS)

Ashley, H.

1984-01-01

Graduate research activity in the following areas is reported: the divergence of laminated composite lifting surfaces, subsonic propeller theory and aeroelastic analysis, and cross sectional resonances in wind tunnels.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Younes, W; Britt, H C; Wilhelmy, J B

The purpose of this note is to combine existing information on the {sup 237}U(n,f) cross section to determine if some consistency can be obtained for the neutron induced fission excitation of {sup 237}U. The neutron induced fission cross section of the 6.8 day {sup 237}U was measured directly by McNally et al. in 1968 using the Pommard nuclear device test. At the same time critical assembly measurements were done at Los Alamos using the Flattop assembly. A previous measurement was also made at LASL in 1954 with two different neutron sources, each peaked near 200 keV. The results were 0.66more » {+-} 0.10 b and 0.70 {+-} 0.07 b for the (n,f) cross section. More recently Younes and Britt have reanalyzed direct reaction charged particle data of Cramer and Britt that had determined the fission probability of the {sup 238}U compound nucleus as a function of nuclear excitation energy. They have combined fission probabilities with calculated neutron absorption cross sections, including corrections for the differences in angular momentum between the direct and neutron induced reactions. From this analysis they have extracted equivalent {sup 237}U(n,f) cross sections. The technique for extracting surrogate (n,f) cross sections from (t,pf) data has been demonstrated in a recent publication for the test case {sup 235}U(n,f). In addition to this experimental information, Lynn and Hayes have recently done a new theoretical study of the fission cross sections for a series of isotopes in this region. A summary plot of the data is shown in Fig. 1. Below 0.5 MeV the McNally, Cowan, and Younes-Britt results are in reasonable agreement. The average cross section in the Younes-Britt results, for En = 0.1 to 0.4 MeV, is 0.80 times the McNally values which is well within the errors of the McNally experiment. Above 0.5 MeV the McNally results diverge toward higher values. It should be noted that this divergence begins approximately at the {sup 237}Np threshold and that {sup 237}Np is the daughter of the 6.8 day {sup 237}U decay.« less

Infant Development in Fragile X Syndrome: Cross-Syndrome Comparisons

ERIC Educational Resources Information Center

Roberts, Jane E.; McCary, Lindsay M.; Shinkareva, Svetlana V.; Bailey, Donald B., Jr.

2016-01-01

This study examined the developmental profile of male infants with fragile X syndrome (FXS) and its divergence from typical development and development of infants at high risk for autism associated with familial recurrence (ASIBs). Participants included 174 boys ranging in age from 5 to 28 months. Cross-sectional profiles on the Mullen Scales of…

The performance of immigrants in the Norwegian labor market.

PubMed

Hayfron, J E

1998-01-01

"This paper tests the assimilation hypothesis with Norwegian data. Using both cross-section and cohort analyses, the results show that the 1970-1979 immigrant cohort experienced an earnings growth of about 11% between 1980 and 1990, when their earnings profile was compared to that of natives. This is lower than the 19% assimilation rate predicted by the cross-section method. On the contrary, the results reveal a rapid earnings divergence across cohorts, and between the 1960-1969 cohort and natives." excerpt

Paramedic Learning Style Preferences and Continuing Medical Education Activities: A Cross-Sectional Survey Study.

PubMed

Staple, Louis; Carter, Alix; Jensen, Jan L; Walker, Mark

2018-01-01

Paramedics participate in continuing medical education (CME) to maintain their skills and knowledge. An understanding of learning styles is important for education to be effective. This study examined the preferred learning styles of ground ambulance paramedics and describes how their preferred learning styles relate to the elective CME activities these paramedics attend. All paramedics (n=1,036) employed in a provincial ground ambulance service were invited to participate in a survey containing three parts: demographics, learning style assessed by the Kolb Learning Style Inventory (LSI), and elective CME activity. 260 paramedics (25%) participated in the survey. Preferred learning styles were: assimilator, 28%; diverger, 25%; converger, 24%; and accommodator, 23%. Advanced life support (ALS) providers had a higher proportion of assimilators (36%), and basic life support (BLS) providers had a higher proportion of divergers (30%). The learning style categories of CME activities attended by paramedics were: assimilators, 25%; divergers, 26%; convergers, 25%; and accommodators, 24%. These results suggest that paramedics are a diverse group of learners, and learning style differs within their demographics. Paramedics attend CME activities that complement all learning styles. Organizations providing education opportunities to paramedics should consider paramedics a diverse learning group when designing their CME programs.

Diverging effects of diabetes mellitus in patients with peripheral artery disease and abdominal aortic aneurysm and the role of advanced glycation end-products: ARTERY study - protocol for a multicentre cross-sectional study.

PubMed

de Vos, L C; Boersema, J; Hillebrands, J L; Schalkwijk, C G; Meerwaldt, R; Breek, J C; Smit, A J; Zeebregts, C J; Lefrandt, J D

2017-04-11

Diabetes mellitus is a well-defined risk factor for peripheral artery disease (PAD), but protects against the development and growth of abdominal aortic aneurysm (AAA). Diabetes mellitus is associated with arterial stiffening and peripheral arterial media sclerosis. Advanced glycation end-products (AGEs) are increased in diabetes mellitus and cardiovascular disease. AGEs are known to form cross-links between proteins and are associated with arterial stiffness. Whether AGEs contribute to the protective effects of diabetes mellitus in AAA is unknown. Therefore, the ARTERY ( A dvanced glycation end-p R oducts in patients with peripheral ar T ery dis E ase and abdominal ao R tic aneur Y sm) study is designed to evaluate the role of AGEs in the diverging effects of diabetes mellitus on AAA and PAD. This cross-sectional multicentre study will compare the amount, type and location of AGEs in the arterial wall in a total of 120 patients with AAA or PAD with and without diabetes mellitus (n=30 per subgroup). Also, local and systemic vascular parameters, including pulse wave velocity, will be measured to evaluate the association between arterial stiffness and AGEs. Finally, AGEs will be measured in serum, urine, and assessed in skin with skin autofluorescence using the AGE Reader. This study is approved by the Medical Ethics committees of University Medical Center Groningen, Martini Hospital and Medisch Spectrum Twente, the Netherlands. Study results will be disseminated through peer-reviewed journals and scientific events. trialregister.nl NTR 5363. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Scattering of glue by glue on the light-cone worldsheet. II. Helicity conserving amplitudes

NASA Astrophysics Data System (ADS)

Chakrabarti, D.; Qiu, J.; Thorn, C. B.

2006-08-01

This is the second of a pair of articles on scattering of glue by glue, in which we give the light-cone gauge calculation of the one-loop on-shell helicity conserving scattering amplitudes for gluon-gluon scattering (neglecting quark loops). The 1/p+ factors in the gluon propagator are regulated by replacing p+ integrals with discretized sums omitting the p+=0 terms in each sum. We also employ a novel ultraviolet regulator that is convenient for the light-cone worldsheet description of planar Feynman diagrams. The helicity conserving scattering amplitudes are divergent in the infrared. The infrared divergences in the elastic one-loop amplitude are shown to cancel, in their contribution to cross sections, against ones in the cross section for unseen bremsstrahlung gluons. We include here the explicit calculation of the latter, because it assumes an unfamiliar form due to the peculiar way discretization of p+ regulates infrared divergences. In resolving the infrared divergences we employ a covariant definition of jets, which allows a transparent demonstration of the Lorentz invariance of our final results. Because we use an explicit cutoff of the ultraviolet divergences in exactly four spacetime dimensions, we must introduce explicit counterterms to achieve this final covariant result. These counterterms are polynomials in the external momenta of the precise order dictated by power counting. We discuss the modifications they entail for the light-cone worldsheet action that reproduces the bare planar diagrams of the gluonic sector of QCD. The simplest way to do this is to interpret the QCD string as moving in six spacetime dimensions.

s-wave threshold in electron attachment - Results in 2-C4F6 and CFCl3 at ultra-low electron energies

NASA Technical Reports Server (NTRS)

Chutjian, A.; Alajajian, S. H.; Ajello, J. M.; Orient, O. J.

1984-01-01

Electron attachment lineshapes and cross sections are reported for the processes 2-C4F6(-)/2-C4F6 and Cl(-)/CFCl3 at electron energies of 0-120 and 0-140 meV, and at resolutions of 6 and 7 meV (FWHM), respectively. As in previous measurements in CCl4 and SF6, the results show resolution-limited narrow structure in the cross section at electron energies below 15 meV. This structure arises from the divergence of the s-wave cross section in the limit of zero electron energy. Comparisons are given with swarm-measured results, and with collisional ionization (high-Rydberg attachment) data in this energy range.

A cross-sectional study of learning styles among continuing medical education participants.

PubMed

Collins, C Scott; Nanda, Sanjeev; Palmer, Brian A; Mohabbat, Arya B; Schleck, Cathy D; Mandrekar, Jayawant N; Mahapatra, Saswati; Beckman, Thomas J; Wittich, Christopher M

2018-04-27

Experiential learning has been suggested as a framework for planning continuing medical education (CME). We aimed to (1) determine participants' learning styles at traditional CME courses and (2) explore associations between learning styles and participant characteristics. Cross-sectional study of all participants (n = 393) at two Mayo Clinic CME courses who completed the Kolb Learning Style Inventory and provided demographic data. A total of 393 participants returned 241 surveys (response rate, 61.3%). Among the 143 participants (36.4%) who supplied complete demographic and Kolb data, Kolb learning styles included diverging (45; 31.5%), assimilating (56; 39.2%), converging (8; 5.6%), and accommodating (34; 23.8%). Associations existed between learning style and gender (p = 0.02). For most men, learning styles were diverging (23 of 63; 36.5%) and assimilating (30 of 63; 47.6%); for most women, diverging (22 of 80; 27.5%), assimilating (26 of 80; 32.5%), and accommodating (26 of 80; 32.5%). Internal medicine and psychiatry CME participants had diverse learning styles. Female participants had more variation in their learning styles than men. Teaching techniques must vary to appeal to all learners. The experiential learning theory sequentially moves a learner from Why? to What? to How? to If? to accommodate learning styles.

Fluid mixing in droplet-based microfluidics with T junction and convergent-divergent sinusoidal microchannels.

PubMed

Yang, Li; Li, Shanshan; Liu, Jixiao; Cheng, Jingmeng

2018-02-01

To explore and utilize the advantages of droplet-based microfluidics, hydrodynamics, and mixing process within droplets traveling though the T junction channel and convergent-divergent sinusoidal microchannels are studied by numerical simulations and experiments, respectively. In the T junction channel, the mixing efficiency is significantly influenced by the twirling effect, which controls the initial distributions of the mixture during the droplet formation stage. Therefore, the internal recirculating flow can create a convection mechanism, thus improving mixing. The twirling effect is noticeably influenced by the velocity of the continuous phase; in the sinusoidal channel, the Dean vortices and droplet deformation are induced by centrifugal force and alternative velocity gradient, thus enhancing the mixing efficiency. The best mixing occurred when the droplet size is comparable with the channel width. Finally, we propose a unique optimized structure, which includes a T junction inlet joined to a sinusoidal channel. In this structure, the mixing of fluids in the droplets follows two routes: One is the twirling effect and symmetric recirculation flow in the straight channel. The other is the asymmetric recirculation and droplet deformation in the winding and variable cross-section. Among the three structures, the optimized structure has the best mixing efficiency at the shortest mixing time (0.25 ms). The combination of the twirling effect, variable cross-section effect, and Dean vortices greatly intensifies the chaotic flow. This study provides the insight of the mixing process and may benefit the design and operations of droplet-based microfluidics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thrust characteristics of a series of convergent-divergent exhaust nozzles at subsonic and supersonic flight speeds

NASA Technical Reports Server (NTRS)

Fradenburgh, Evan A; Gorton, Gerald C; Beke, Andrew

1954-01-01

An experimental investigation of a series of four convergent-divergent exhaust nozzles was conducted in the Lewis 8-by-6 foot supersonic wind tunnel at Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a range of nozzle pressure ratios. The thrust characteristics of these nozzles were determined by a pressure-integration technique. From a thrust standpoint, a nozzle designed to give uniform parallel flow at the exit had no advantage over the simple geometric design with conical convergent and divergent sections. The rapid-divergent nozzles might be competitive with the more gradual-divergent nozzles since the relatively short length of these nozzles would be advantageous from a weight standpoint and might result in smaller thrust losses due to friction. The thrusts, with friction losses neglected, were predicted satisfactorily by one-dimensional theory for the nozzles with relatively gradual divergence. The thrusts of the rapid-divergent designs were several percentages below the theoretical values at the design pressure ratio or above, while at low pressure ratios there was a considerable effect of free-stream Mach number, with thrusts considerably above theoretical values at subsonic speeds and somewhat above theoretical values at supersonic speeds. This Mach numb effect appeared to be related to the variation of the model base pressure with free-stream Mach number.

Numerical Optimization of converging diverging miniature cavitating nozzles

NASA Astrophysics Data System (ADS)

Chavan, Kanchan; Bhingole, B.; Raut, J.; Pandit, A. B.

2015-12-01

The work focuses on the numerical optimization of converging diverging cavitating nozzles through nozzle dimensions and wall shape. The objective is to develop design rules for the geometry of cavitating nozzles for desired end-use. Two main aspects of nozzle design which affects the cavitation have been studied i.e. end dimensions of the geometry (i.e. angle and/or curvature of the inlet, outlet and the throat and the lengths of the converging and diverging sections) and wall curvatures(concave or convex). Angle of convergence at the inlet was found to control the cavity growth whereas angle of divergence of the exit controls the collapse of cavity. CFD simulations were carried out for the straight line converging and diverging sections by varying converging and diverging angles to study its effect on the collapse pressure generated by the cavity. Optimized geometry configurations were obtained on the basis of maximum Cavitational Efficacy Ratio (CER)i.e. cavity collapse pressure generated for a given permanent pressure drop across the system. With increasing capabilities in machining and fabrication, it is possible to exploit the effect of wall curvature to create nozzles with further increase in the CER. Effect of wall curvature has been studied for the straight, concave and convex shapes. Curvature has been varied and effect of concave and convex wall curvatures vis-à-vis straight walls studied for fixed converging and diverging angles.It is concluded that concave converging-diverging nozzles with converging angle of 20° and diverging angle of 5° with the radius of curvature 0.03 m and 0.1530 m respectively gives maximum CER. Preliminary experiments using optimized geometry are indicating similar trends and are currently being carried out. Refinements of the CFD technique using two phase flow simulations are planned.

A Least-Squares Finite Element Method for Electromagnetic Scattering Problems

NASA Technical Reports Server (NTRS)

Wu, Jie; Jiang, Bo-nan

1996-01-01

The least-squares finite element method (LSFEM) is applied to electromagnetic scattering and radar cross section (RCS) calculations. In contrast to most existing numerical approaches, in which divergence-free constraints are omitted, the LSFF-M directly incorporates two divergence equations in the discretization process. The importance of including the divergence equations is demonstrated by showing that otherwise spurious solutions with large divergence occur near the scatterers. The LSFEM is based on unstructured grids and possesses full flexibility in handling complex geometry and local refinement Moreover, the LSFEM does not require any special handling, such as upwinding, staggered grids, artificial dissipation, flux-differencing, etc. Implicit time discretization is used and the scheme is unconditionally stable. By using a matrix-free iterative method, the computational cost and memory requirement for the present scheme is competitive with other approaches. The accuracy of the LSFEM is verified by several benchmark test problems.

The NASA Langley Isolator Dynamics Research Lab

NASA Technical Reports Server (NTRS)

Middleton, Troy F.; Balla, Robert J.; Baurle, Robert A.; Humphreys, William M.; Wilson, Lloyd G.

2010-01-01

The Isolator Dynamics Research Lab (IDRL) is under construction at the NASA Langley Research Center in Hampton, Virginia. A unique test apparatus is being fabricated to support both wall and in-stream measurements for investigating the internal flow of a dual-mode scramjet isolator model. The test section is 24 inches long with a 1-inch by 2-inch cross sectional area and is supplied with unheated, dry air through a Mach 2.5 converging-diverging nozzle. The test section is being fabricated with two sets (glass and metallic) of interchangeable sidewalls to support flow visualization and laser-based measurement techniques as well as static pressure, wall temperature, and high frequency pressure measurements. During 2010, a CFD code validation experiment will be conducted in the lab in support of NASA s Fundamental Aerodynamics Program. This paper describes the mechanical design of the Isolator Dynamics Research Lab test apparatus and presents a summary of the measurement techniques planned for investigating the internal flow field of a scramjet isolator model.

Supersonic compressor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, II, William Byron; Lawlor, Shawn P.; Breidenthal, Robert E.

A supersonic compressor including a rotor to deliver a gas at supersonic conditions to a diffuser. The diffuser includes a plurality of aerodynamic ducts that have converging and diverging portions, for deceleration of gas to subsonic conditions and then for expansion of subsonic gas, to change kinetic energy of the gas to static pressure. The aerodynamic ducts include vortex generating structures for controlling boundary layer, and structures for changing the effective contraction ratio to enable starting even when the aerodynamic ducts are designed for high pressure ratios, and structures for boundary layer control. In an embodiment, aerodynamic ducts are providedmore » having an aspect ratio of in excess of two to one, when viewed in cross-section orthogonal to flow direction at an entrance to the aerodynamic duct.« less

Refraction at a curved dielectric interface - Geometrical optics solution

NASA Technical Reports Server (NTRS)

Lee, S.-W.; Sheshadri, M. S.; Mittra, R.; Jamnejad, V.

1982-01-01

The transmission of a spherical or plane wave through an arbitrarily curved dielectric interface is solved by the geometrical optics theory. The transmitted field is proportional to the product of the conventional Fresnel's transmission coefficient and a divergence factor (DF), which describes the cross-sectional variation (convergence or divergence) of a ray pencil as the latter propagates in the transmitted region. The factor DF depends on the incident wavefront, the curvatures of the interface, and the relative indices of the two media. Explicit matrix formulas for calculating DF are given, and its physical significance is illustrated via examples.

Single lens system for forward-viewing navigation and scanning side-viewing optical coherence tomography

NASA Astrophysics Data System (ADS)

Tate, Tyler H.; McGregor, Davis; Barton, Jennifer K.

2017-02-01

The optical design for a dual modality endoscope based on piezo scanning fiber technology is presented including a novel technique to combine forward-viewing navigation and side viewing OCT. Potential applications include navigating body lumens such as the fallopian tube, biliary ducts and cardiovascular system. A custom cover plate provides a rotationally symmetric double reflection of the OCT beam to deviate and focus the OCT beam out the side of the endoscope for cross-sectional imaging of the tubal lumen. Considerations in the choice of the scanning fiber are explored and a new technique to increase the divergence angle of the scanning fiber to improve system performance is presented. Resolution and the necessary scanning density requirements to achieve Nyquist sampling of the full image are considered. The novel optical design lays the groundwork for a new approach integrating side-viewing OCT into multimodality endoscopes for small lumen imaging. KEYWORDS:

The Role of Electroweak Corrections for the Dark Matter Relic Abundance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ciafaloni, Paolo; Comelli, Denis; Simone, Andrea De

2013-10-01

We analyze the validity of the theorems concerning the cancellation of the infrared and collinar divergences in the case of dark matter freeze-out in the early universe. In particular, we compute the electroweak logarithmic corrections of infrared origin to the annihilation cross section of a dark matter particle being the neutral component of a SU(2){sub L} multiplet. The inclusion of processes with final state W can modify significantly the cross sections computed with only virtual W exchange. Our results show that the inclusion of infrared logs is necessary for a precise computation of the dark matter relic abundance.

Focusing adaptive-optics for neutron spectroscopy at extreme conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simeoni, G. G., E-mail: ggsimeoni@outlook.com; Physics Department E13, Technical University of Munich, D-85748 Garching; Valicu, R. G.

2015-12-14

Neutron Spectroscopy employing extreme-conditions sample environments is nowadays a crucial tool for the understanding of fundamental scientific questions as well as for the investigation of materials and chemical-physical properties. For all these kinds of studies, an increased neutron flux over a small sample area is needed. The prototype of a focusing neutron guide component, developed and produced completely at the neutron source FRM II in Garching (Germany), has been installed at the time-of-flight (TOF) disc-chopper neutron spectrometer TOFTOF and came into routine-operation. The design is based on the compressed Archimedes' mirror concept for finite-size divergent sources. It represents a uniquemore » device combining the supermirror technology with Adaptive Optics, suitable for broad-bandwidth thermal-cold TOF neutron spectroscopy (here optimized for 1.4–10 Å). It is able to squeeze the beam cross section down to a square centimeter, with a more than doubled signal-to-background ratio, increased efficiency at high scattering angles, and improved symmetry of the elastic resolution function. We present a comparison between the simulated and measured beam cross sections, as well as the performance of the instrument within real experiments. This work intends to show the unprecedented opportunities achievable at already existing instruments, along with useful guidelines for the design and construction of next-generation neutron spectrometers.« less

Comparative architectural properties of limb muscles in Crocodylidae and Alligatoridae and their relevance to divergent use of asymmetrical gaits in extant Crocodylia.

PubMed

Allen, Vivian; Molnar, Julia; Parker, William; Pollard, Andrea; Nolan, Grant; Hutchinson, John R

2014-12-01

Crocodiles and their kin (Crocodylidae) use asymmetrical (bounding and galloping) gaits when moving rapidly. Despite being morphologically and ecologically similar, it seems alligators and their kin (Alligatoridae) do not. To investigate a possible anatomical basis for this apparent major difference in locomotor capabilities, we measured relative masses and internal architecture (fascicle lengths and physiological cross-sectional areas) of muscles of the pectoral and pelvic limbs of 40 individuals from six representative species of Crocodylidae and Alligatoridae. We found that, relative to body mass, Crocodylidae have significantly longer muscle fascicles (increased working range), particularly in the pectoral limb, and generally smaller muscle physiological cross-sectional areas (decreased force-exerting capability) than Alligatoridae. We therefore hypothesise that the ability of some crocodylians to use asymmetrical gaits may be limited more by the ability to make large, rapid limb motions (especially in the pectoral limb) than the ability to exert large limb forces. Furthermore, analysis of scaling patterns in muscle properties shows that limb anatomy in the two clades becomes more divergent during ontogeny. Limb muscle masses, fascicle lengths and physiological cross-sectional areas scale with significantly larger coefficients in Crocodylidae than Alligatoridae. This combination of factors suggests that inter-clade disparity in maximal limb power is highest in adult animals. Therefore, despite their apparent morphological similarities, both mean values and scaling patterns suggest that considerable diversity exists in the locomotor apparatus of extant Crocodylia. © 2014 Anatomical Society.

Effect of thermodynamic disequilibrium on critical liquid-vapor flow conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bilicki, Z.; Kestin, J.

1989-01-01

In this lecture we characterize the effect of absence of unconstrained thermodynamic equilibrium and onset of a metastable state on the adiabatic flow of a mixture of liquid and its vapor through a convergent-divergent nozzle. We study steady-state flows and emphasize the relations that are present when the flow is choked. In such cases, there exists a cross-section in which the flow is critical and in which the adiabatic wave of small amplitude is stationary. More precisely, the relaxation process which results from the lack of equilibrium causes the system to be dispersive. In such circumstances, the critical velocity ismore » equal to the frozen speed of sound, a/sub f/ corresponding to /omega/ /yields/ /infinity/. The relaxation process displaces the critical cross-section quite far downstream from the throat and places it in the divergent portion of the channel. We present the topological portrait of solutions in a suitably defined state-velocity space and discuss the potential appearance of normal and dispersed shock waves. In extreme cases, the singular point (usually a saddle) which enables the flow to become supercritical is displaced so far that it is located outside the exit. Then, the flow velocity is everywhere subcritical (w < a/sub f/) even though it may exceed the equilibrium speed of sound (w /approx gt/ a/sub e/) beyond a certain cross-section, and in spite of the presence of a throat. 10 refs., 4 figs.« less

Further insight into reproductive incompatibility between putative cryptic species of the Bemisia tabaci whitefly complex.

PubMed

Qin, Li; Pan, Li-Long; Liu, Shu-Sheng

2016-04-01

The whitefly Bemisia tabaci (Gennadius) (Hemiptera: Aleyrodidae), with its global distribution and extensive genetic diversity, is now known to be a complex of over 35 cryptic species. However, a satisfactory resolution of the systematics of this species complex is yet to be achieved. Here, we designed experiments to examine reproductive compatibility among species with different levels of mitochondrial cytochrome oxidase I (mtCOI) divergence. The data show that putative species with mtCOI divergence of >8% between them consistently exhibited complete reproductive isolation. However, two of the putative species, Asia II 9 and Asia II 3, with mtCOI divergence of 4.47% between them, exhibited near complete reproductive compatibility in one direction of their cross, and partial reproductive compatibility in the other direction. Together with some recent reports on this topic from the literature, our data indicates that, while divergence in the mtCOI sequences provides a valid molecular marker for species delimitation in most clades, more genetic markers and more sophisticated molecular phylogeny will be required to achieve adequate delimitation of all species in this whitefly complex. While many attempts have been made to examine the reproductive compatibility among genetic groups of the B. tabaci complex, our study represents the first effort to conduct crossing experiments with putative species that were chosen with considerations of their genetic divergence. In light of the new data, we discuss the best strategy and protocols to conduct further molecular phylogenetic analysis and crossing trials, in order to reveal the overall pattern of reproductive incompatibility among species of this whitefly complex. © 2015 Institute of Zoology, Chinese Academy of Sciences.

Numerical Investigation of 'Transonic Resonance' with a Convergent-Divergent Nozzle

NASA Technical Reports Server (NTRS)

Loh, Ching Y.; Zaman, K. B. M. Q.

2002-01-01

At pressure ratios lower than the design value, convergent-divergent (C-D) nozzles often undergo a flow resonance accompanied by the emission of acoustic tones. The phenomenon, driven by the unsteady shock within the divergent section of the nozzle, has been studied experimentally by Zaman et al. In this paper, the space-time conservation element solution element (CE/SE) method is employed to numerically investigate the phenomenon. The computations are performed for a given nozzle geometry for several different pressure ratios. Sustained 'limit cycle' oscillations are encountered in all cases. The oscillation frequencies, their variation with pressure ratio including a 'stage jump', agree well with the experimental results. The unsteady flow data confirm that stage 1 of the resonance (fundamental) involves a one-quarter standing wave while stage 2 (third harmonic) involves a three-quarter standing wave within the divergent section of the nozzle. Details of the shock motion, and the flow and near acoustic field, are documented for one case each of stages 1 and 2.

Vortical structures and development of laminar flow over convergent-divergent riblets

NASA Astrophysics Data System (ADS)

Xu, Fang; Zhong, Shan; Zhang, Shanying

2018-05-01

In this work, the development of a laminar boundary layer over a rectangular convergent-divergent riblet section with a finite streamwise length is studied experimentally using dye visualization and particle image velocimetry in a water flume. The flow topology over this highly directional spanwise roughness is established from this study. It is shown that convergent-divergent riblets generate a spanwise flow above the riblets from the diverging line toward the adjacent converging line. This consequently leads to the formation of a weak recirculating secondary flow in cross-stream planes across the boundary layer that creates a downwash motion over the diverging line and an upwash motion over the converging line. It is found that the fluid inside the riblet valley follows a helicoidal path and it also interacts with the crossflow boundary layer hence playing a key role in determining the structure of the secondary flow across the boundary layer. The impact of riblet wavelength on vortical structures is also revealed for the first time. A larger riblet wavelength is seen to produce a stronger upwash/downwash and hence a more intense secondary flow as well as a stronger deceleration effect on the crossflow. Furthermore, the streamwise development of the flow over the riblet section can be divided into a developing stage followed by a developed stage. In the developing stage, the magnitude of induced streamwise velocity and vorticity over the converging line continues to increase, whereas in the developed stage the values of these parameters remain essentially unchanged.

Static Thrust and Vectoring Performance of a Spherical Convergent Flap Nozzle with a Nonrectangular Divergent Duct

NASA Technical Reports Server (NTRS)

Wing, David J.

1998-01-01

The static internal performance of a multiaxis-thrust-vectoring, spherical convergent flap (SCF) nozzle with a non-rectangular divergent duct was obtained in the model preparation area of the Langley 16-Foot Transonic Tunnel. Duct cross sections of hexagonal and bowtie shapes were tested. Additional geometric parameters included throat area (power setting), pitch flap deflection angle, and yaw gimbal angle. Nozzle pressure ratio was varied from 2 to 12 for dry power configurations and from 2 to 6 for afterburning power configurations. Approximately a 1-percent loss in thrust efficiency from SCF nozzles with a rectangular divergent duct was incurred as a result of internal oblique shocks in the flow field. The internal oblique shocks were the result of cross flow generated by the vee-shaped geometric throat. The hexagonal and bowtie nozzles had mirror-imaged flow fields and therefore similar thrust performance. Thrust vectoring was not hampered by the three-dimensional internal geometry of the nozzles. Flow visualization indicates pitch thrust-vector angles larger than 10' may be achievable with minimal adverse effect on or a possible gain in resultant thrust efficiency as compared with the performance at a pitch thrust-vector angle of 10 deg.

Low-temperature collisional quenching of NO A{sup 2}Σ{sup +}(v′ = 0) by NO(X{sup 2}Π) and O{sub 2} between 34 and 109 K

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sánchez-González, R.; Eveland, W. D.; West, N. A.

2014-08-21

We present measurements of collisional fluorescence quenching cross sections of NO(A{sup 2}Σ{sup +}, v′ = 0) by NO(X{sup 2}Π) and O{sub 2} between 34 and 109 K using a pulsed converging-diverging nozzle gas expansion, extending the temperature range of previous measurements. The thermally averaged fluorescence quenching cross sections for both species show a monotonic increase as temperature decreases in this temperature range, consistent with earlier observations. These new measurements, however, allow discrimination between predictions obtained by extrapolating fits of previous data using different functional forms that show discrepancies exceeding 120% for NO and 160% for O{sub 2} at 34 K.more » The measured self-quenching cross section is 52.9 Å{sup 2} near 112 K and increases to 64.1 Å{sup 2} at 35 K, whereas the O{sub 2} fluorescence quenching cross section is 42.9 Å{sup 2} at 109 K and increases to 58.3 Å{sup 2} at 34 K. Global fits of the quenching cross section temperature dependence show that, when including our current measurements, the low temperature behavior of the quenching cross sections for NO and O{sub 2} is better described by a parameterization that accounts for the long-range interactions leading to the collisional deactivation via an inverse power law model.« less

Influence of strut cross-section of stents on local hemodynamics in stented arteries

NASA Astrophysics Data System (ADS)

Jiang, Yongfei; Zhang, Jun; Zhao, Wanhua

2016-05-01

Stenting is a very effective treatment for stenotic vascular diseases, but vascular geometries altered by stent implantation may lead to flow disturbances which play an important role in the initiation and progression of restenosis, especially in the near wall in stented arterial regions. So stent designs have become one of the indispensable factors needed to be considered for reducing the flow disturbances. In this paper, the structural designs of strut cross-section are considered as an aspect of stent designs to be studied in details. Six virtual stents with different strut cross-section are designed for deployments in the same ideal arterial model. Computational fluid dynamics (CFD) methods are performed to study how the shape and the aspect ratio (AR) of strut cross-section modified the local hemodynamics in the stented segments. The results indicate that stents with different strut cross-sections have different influence on the hemodynamics. Stents with streamlined cross-sectional struts for circular arc or elliptical arc can significantly enhance wall shear stress (WSS) in the stented segments, and reduce the flow disturbances around stent struts. The performances of stents with streamlined cross-sectional struts are better than that of stents with non-streamlined cross-sectional struts for rectangle. The results also show that stents with a larger AR cross-section are more conductive to improve the blood flow. The present study provides an understanding of the flow physics in the vicinity of stent struts and indicates that the shape and AR of strut cross-section ought to be considered as important factors to minimize flow disturbance in stent designs.

Electroweak gauge-boson production at small q T : Infrared safety from the collinear anomaly

NASA Astrophysics Data System (ADS)

Becher, Thomas; Neubert, Matthias; Wilhelm, Daniel

2012-02-01

Using methods from effective field theory, we develop a novel, systematic framework for the calculation of the cross sections for electroweak gauge-boson production at small and very small transverse momentum q T , in which large logarithms of the scale ratio M V /q T are resummed to all orders. These cross sections receive logarithmically enhanced corrections from two sources: the running of the hard matching coefficient and the collinear factorization anomaly. The anomaly leads to the dynamical generation of a non-perturbative scale {q_* } ˜ {M_V}{e^{ - {text{const}}/{α_s}left( {{M_V}} right)}} , which protects the processes from receiving large long-distance hadronic contributions. Expanding the cross sections in either α s or q T generates strongly divergent series, which must be resummed. As a by-product, we obtain an explicit non-perturbative expression for the intercept of the cross sections at q T = 0, including the normalization and first-order α s ( q ∗ ) correction. We perform a detailed numerical comparison of our predictions with the available data on the transverse-momentum distribution in Z-boson production at the Tevatron and LHC.

Maternal and child mortality indicators across 187 countries of the world: converging or diverging.

PubMed

Goli, Srinivas; Arokiasamy, Perianayagam

2014-01-01

This study reassessed the progress achieved since 1990 in maternal and child mortality indicators to test whether the progress is converging or diverging across countries worldwide. The convergence process is examined using standard parametric and non-parametric econometric models of convergence. The results of absolute convergence estimates reveal that progress in maternal and child mortality indicators is diverging for the entire period of 1990-2010 [maternal mortality ratio (MMR) - β = .00033, p < .574; neonatal mortality rate (NNMR) - β = .04367, p < .000; post-neonatal mortality rate (PNMR) - β = .02677, p < .000; under-five mortality rate (U5MR) - β = .00828, p < .000)]. In the recent period, such divergence is replaced with convergence for MMR but diverged for all the child mortality indicators. The results of Kernel density estimate reveal considerable reduction in divergence of MMR for the recent period; however, the Kernel density distribution plots show more than one 'peak' which indicates the emergence of convergence clubs based on their mortality levels. For child mortality indicators, the Kernel estimates suggest that divergence is in progress across the countries worldwide but tended to converge for countries with low mortality levels. A mere progress in global averages of maternal and child mortality indicators among a global cross-section of countries does not warranty convergence unless there is a considerable reduction in variance, skewness and range of change.

Dynamic Investigation of Static Divergence: Analysis and Testing

NASA Technical Reports Server (NTRS)

Heeg, Jennifer

2000-01-01

The phenomenon known as aeroelastic divergence is the focus of this work. The analyses and experiment presented here show that divergence can occur without a structural dynamic mode losing its oscillatory nature. Aeroelastic divergence occurs when the structural restorative capability or stiffness of a structure is overwhelmed by the static aerodynamic moment. This static aeroelastic coupling does not require the structural dynamic system behavior to cease, however. Aeroelastic changes in the dynamic mode behavior are governed not only by the stiffness, but by damping and inertial properties. The work presented here supports these fundamental assertions by examining a simple system: a typical section airfoil with only a rotational structural degree of freedom. Analytical results identified configurations that exhibit different types of dynamic mode behavior as the system encounters divergence. A wind tunnel model was designed and tested to examine divergence experimentally. The experimental results validate the analytical calculations and explicitly examine the divergence phenomenon where the dynamic mode persists. Three configurations of the wind tunnel model were tested. The experimental results agree very well with the analytical predictions of subcritical characteristics, divergence velocity, and behavior of the noncritical dynamic mode at divergence.

Evidence of Validity for the Japanese Version of the Foot and Ankle Ability Measure

PubMed Central

Uematsu, Daisuke; Suzuki, Hidetomo; Sasaki, Shogo; Nagano, Yasuharu; Shinozuka, Nobuyuki; Sunagawa, Norihiko; Fukubayashi, Toru

2015-01-01

Context: The Foot and Ankle Ability Measure (FAAM) is a valid, reliable, and self-reported outcome instrument for the foot and ankle region. Objective: To provide evidence for translation, cross-cultural adaptation, validity, and reliability of the Japanese version of the FAAM (FAAM-J). Design: Cross-sectional study. Setting: Collegiate athletic training/sports medicine clinical setting. Patients or Other Participants: Eighty-three collegiate athletes. Main Outcome Measure(s): All participants completed the Activities of Daily Living and Sports subscales of the FAAM-J and the Physical Functioning and Mental Health subscales of the Japanese version of the Short Form-36v2 (SF-36). Also, 19 participants (23%) whose conditions were expected to be stable completed another FAAM-J 2 to 6 days later for test-retest reliability. We analyzed the scores of those subscales for convergent and divergent validity, internal consistency, and test-retest reliability. Results: The Activities of Daily Living and Sports subscales of the FAAM-J had correlation coefficients of 0.86 and 0.75, respectively, with the Physical Functioning section of the SF-36 for convergent validity. For divergent validity, the correlation coefficients with Mental Health of the SF-36 were 0.29 and 0.27 for each subscale, respectively. Cronbach α for internal consistency was 0.99 for the Activities of Daily Living and 0.98 for the Sports subscale. A 95% confidence interval with a single measure was ±8.1 and ±14.0 points for each subscale. The test-retest reliability measures revealed intraclass correlation coefficient values of 0.87 for the Activities of Daily Living and 0.91 for the Sports subscales with minimal detectable changes of ±6.8 and ±13.7 for the respective subscales. Conclusions: The FAAM was successfully translated for a Japanese version, and the FAAM-J was adapted cross-culturally. Thus, the FAAM-J can be used as a self-reported outcome measure for Japanese-speaking individuals; however, the scores must be interpreted with caution, especially when applied to different populations and other types of injury than those included in this study. PMID:25310247

A scalable block-preconditioning strategy for divergence-conforming B-spline discretizations of the Stokes problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cortes, Adriano M.; Dalcin, Lisandro; Sarmiento, Adel F.

The recently introduced divergence-conforming B-spline discretizations allow the construction of smooth discrete velocity–pressure pairs for viscous incompressible flows that are at the same time inf–sup stable and pointwise divergence-free. When applied to the discretized Stokes problem, these spaces generate a symmetric and indefinite saddle-point linear system. The iterative method of choice to solve such system is the Generalized Minimum Residual Method. This method lacks robustness, and one remedy is to use preconditioners. For linear systems of saddle-point type, a large family of preconditioners can be obtained by using a block factorization of the system. In this paper, we show howmore » the nesting of “black-box” solvers and preconditioners can be put together in a block triangular strategy to build a scalable block preconditioner for the Stokes system discretized by divergence-conforming B-splines. Lastly, besides the known cavity flow problem, we used for benchmark flows defined on complex geometries: an eccentric annulus and hollow torus of an eccentric annular cross-section.« less

A scalable block-preconditioning strategy for divergence-conforming B-spline discretizations of the Stokes problem

DOE PAGES

Cortes, Adriano M.; Dalcin, Lisandro; Sarmiento, Adel F.; ...

2016-10-19

The recently introduced divergence-conforming B-spline discretizations allow the construction of smooth discrete velocity–pressure pairs for viscous incompressible flows that are at the same time inf–sup stable and pointwise divergence-free. When applied to the discretized Stokes problem, these spaces generate a symmetric and indefinite saddle-point linear system. The iterative method of choice to solve such system is the Generalized Minimum Residual Method. This method lacks robustness, and one remedy is to use preconditioners. For linear systems of saddle-point type, a large family of preconditioners can be obtained by using a block factorization of the system. In this paper, we show howmore » the nesting of “black-box” solvers and preconditioners can be put together in a block triangular strategy to build a scalable block preconditioner for the Stokes system discretized by divergence-conforming B-splines. Lastly, besides the known cavity flow problem, we used for benchmark flows defined on complex geometries: an eccentric annulus and hollow torus of an eccentric annular cross-section.« less

Performance Characteristics of Plane-Wall Two-Dimensional Diffusers

NASA Technical Reports Server (NTRS)

Reid, Elliott G

1953-01-01

Experiments have been made at Stanford University to determine the performance characteristics of plane-wall, two-dimensional diffusers which were so proportioned as to insure reasonable approximation of two-dimensional flow. All of the diffusers had identical entrance cross sections and discharged directly into a large plenum chamber; the test program included wide variations of divergence angle and length. During all tests a dynamic pressure of 60 pounds per square foOt was maintained at the diffuser entrance and the boundary layer there was thin and fully turbulent. The most interesting flow characteristics observed were the occasional appearance of steady, unseparated, asymmetric flow - which was correlated with the boundary-layer coalescence - and the rapid deterioration of flow steadiness - which occurred as soon as the divergence angle for maximum static pressure recovery was exceeded. Pressure efficiency was found to be controlled almost exclusively by divergence angle, whereas static pressure recovery was markedly influenced by area ratio (or length) as well as divergence angle. Volumetric efficiency. diminished as area ratio increased, and at a greater rate with small lengths than with large ones. Large values of the static-pressure-recovery coefficient were attained only with long diffusers of large area ratio; under these conditions pressure efficiency was high and. volumetric efficiency low. Auxiliary tests with asymmetric diffusers demonstrated that longitudinal pressure gradient, rather than wall divergence angle, controlled flow separation. Others showed that the addition of even a short exit duct of uniform section augmented pressure recovery. Finally, it was found that the installation of a thin, central, longitudinal partition suppressed flow separation in short diffusers and thereby improved pressure recovery

Methodology Series Module 3: Cross-sectional Studies.

PubMed

Setia, Maninder Singh

2016-01-01

Cross-sectional study design is a type of observational study design. In a cross-sectional study, the investigator measures the outcome and the exposures in the study participants at the same time. Unlike in case-control studies (participants selected based on the outcome status) or cohort studies (participants selected based on the exposure status), the participants in a cross-sectional study are just selected based on the inclusion and exclusion criteria set for the study. Once the participants have been selected for the study, the investigator follows the study to assess the exposure and the outcomes. Cross-sectional designs are used for population-based surveys and to assess the prevalence of diseases in clinic-based samples. These studies can usually be conducted relatively faster and are inexpensive. They may be conducted either before planning a cohort study or a baseline in a cohort study. These types of designs will give us information about the prevalence of outcomes or exposures; this information will be useful for designing the cohort study. However, since this is a 1-time measurement of exposure and outcome, it is difficult to derive causal relationships from cross-sectional analysis. We can estimate the prevalence of disease in cross-sectional studies. Furthermore, we will also be able to estimate the odds ratios to study the association between exposure and the outcomes in this design.

Methodology Series Module 3: Cross-sectional Studies

PubMed Central

Setia, Maninder Singh

2016-01-01

Cross-sectional study design is a type of observational study design. In a cross-sectional study, the investigator measures the outcome and the exposures in the study participants at the same time. Unlike in case–control studies (participants selected based on the outcome status) or cohort studies (participants selected based on the exposure status), the participants in a cross-sectional study are just selected based on the inclusion and exclusion criteria set for the study. Once the participants have been selected for the study, the investigator follows the study to assess the exposure and the outcomes. Cross-sectional designs are used for population-based surveys and to assess the prevalence of diseases in clinic-based samples. These studies can usually be conducted relatively faster and are inexpensive. They may be conducted either before planning a cohort study or a baseline in a cohort study. These types of designs will give us information about the prevalence of outcomes or exposures; this information will be useful for designing the cohort study. However, since this is a 1-time measurement of exposure and outcome, it is difficult to derive causal relationships from cross-sectional analysis. We can estimate the prevalence of disease in cross-sectional studies. Furthermore, we will also be able to estimate the odds ratios to study the association between exposure and the outcomes in this design. PMID:27293245

An Investigation of Convergent-Divergent Diffusers at Mach Number 1.85

NASA Technical Reports Server (NTRS)

Wyatt, Demarquis D; Hunczak, Henry R

1947-01-01

An investigation has been conducted in the Cleveland 18- by 18-inch supersonic tunnel at a Mach number of 1.85 and angles of attack from 0 deg to 5 deg to determine optimum design configurations for a convergent-divergent type of supersonic diffuser with a subsonic diffuser of 5 deg included divergence angle. Total pressure recoveries in excess of theoretical recovery across a normal shock at a free-stream Mach number of 1.85 wore obtained with several configurations. The highest recovery for configurations without a cylindrical throat section was obtained with an inlet having an included convergence angle of 20 deg. Insertion of a 2-inch throat section between a 10 deg included angle inlet and the subsonic diffuser stabilized the shock inside the diffuser and resulted in recoveries as high as 0.838 free-stream total pressure at an angle of attack of 0 deg, corresponding to recovery of 92.4 percent of the kinetic energy of the free air stream. Use of the throat section also lessened the reduction in recovery of all configurations due to angle of attack.

Correction of sampling bias in a cross-sectional study of post-surgical complications.

PubMed

Fluss, Ronen; Mandel, Micha; Freedman, Laurence S; Weiss, Inbal Salz; Zohar, Anat Ekka; Haklai, Ziona; Gordon, Ethel-Sherry; Simchen, Elisheva

2013-06-30

Cross-sectional designs are often used to monitor the proportion of infections and other post-surgical complications acquired in hospitals. However, conventional methods for estimating incidence proportions when applied to cross-sectional data may provide estimators that are highly biased, as cross-sectional designs tend to include a high proportion of patients with prolonged hospitalization. One common solution is to use sampling weights in the analysis, which adjust for the sampling bias inherent in a cross-sectional design. The current paper describes in detail a method to build weights for a national survey of post-surgical complications conducted in Israel. We use the weights to estimate the probability of surgical site infections following colon resection, and validate the results of the weighted analysis by comparing them with those obtained from a parallel study with a historically prospective design. Copyright © 2012 John Wiley & Sons, Ltd.

The Relation between Gray Matter Morphology and Divergent Thinking in Adolescents and Young Adults

PubMed Central

Zanolie, Kiki; Kleibeuker, Sietske W.; Crone, Eveline A.

2014-01-01

Adolescence and early adulthood are developmental time periods during which creative cognition is highly important for adapting to environmental changes. Divergent thinking, which refers to generating novel and useful solutions to open-ended problems, has often been used as a measure of creative cognition. The first goal of this structural neuroimaging study was to elucidate the relationship between gray matter morphology and performance in the verbal (AUT; alternative uses task) and visuo-spatial (CAT; creative ability test) domain of divergent thinking in adolescents and young adults. The second goal was to test if gray matter morphology is related to brain activity during AUT performance. Neural and behavioral data were combined from a cross-sectional study including 25 adolescents aged 15–17 and 20 young adults aged 25–30. Brain-behavior relationships were assessed without a priori location assumptions and within areas that were activated during an AUT-scanner task. Gray matter volume and cortical thickness were not significantly associated with verbal divergent thinking. However, visuo-spatial divergent thinking (CAT originality and fluency) was positively associated with cortical thickness of the right middle temporal gyrus and left brain areas including the superior frontal gyrus and various occipital, parietal, and temporal areas, independently of age. AUT brain activity was not associated with cortical thickness. The results support an important role of a widespread brain network involved in flexible visuo-spatial divergent thinking, providing evidence for a relation between cortical thickness and visuo-spatial divergent thinking in adolescents and young adults. However, studies including visuo-spatial divergent thinking tasks in the scanner are warranted. PMID:25514366

Dangerous subtlety: relationship-related determinants of consistency of condom use among female sex workers and their regular, non-commercial partners in Hai Phong, Viet Nam.

PubMed

Hoffman, Leah; Nguyen, Ha Thi Thu; Kershaw, Trace S; Niccolai, Linda M

2011-10-01

Research indicates female sex workers use condoms more consistently with their clients than with regular, non-commercial partners (partners). The purpose of this study was to better understand the relationship between couple communication and HIV risk behavior by examining (1) sex worker-partner divergence on communication measures and (2) the association between intra-couple communication divergence and consistent condom use. In this cross-sectional study, 50 sex workers and their partners in Hai Phong, Viet Nam were separately asked about their relationships and condom use. When asked about HIV risk communication in their relationship, sex workers reported significantly higher HIV communication content than their partners (p < 0.001). Higher communication divergence between partners was associated with a decreased likelihood of consistent condom use (OR 0.54 95% CI 0.30, 0.97). Sex workers urgently need interventions that build their communication skills and address their risk behavior in non-commercial relationships.

A probabilistic methodology for radar cross section prediction in conceptual aircraft design

NASA Astrophysics Data System (ADS)

Hines, Nathan Robert

System effectiveness has increasingly become the prime metric for the evaluation of military aircraft. As such, it is the decision maker's/designer's goal to maximize system effectiveness. Industry and government research documents indicate that all future military aircraft will incorporate signature reduction as an attempt to improve system effectiveness and reduce the cost of attrition. Today's operating environments demand low observable aircraft which are able to reliably take out valuable, time critical targets. Thus it is desirable to be able to design vehicles that are balanced for increased effectiveness. Previous studies have shown that shaping of the vehicle is one of the most important contributors to radar cross section, a measure of radar signature, and must be considered from the very beginning of the design process. Radar cross section estimation should be incorporated into conceptual design to develop more capable systems. This research strives to meet these needs by developing a conceptual design tool that predicts radar cross section for parametric geometries. This tool predicts the absolute radar cross section of the vehicle as well as the impact of geometry changes, allowing for the simultaneous tradeoff of the aerodynamic, performance, and cost characteristics of the vehicle with the radar cross section. Furthermore, this tool can be linked to a campaign theater analysis code to demonstrate the changes in system and system of system effectiveness due to changes in aircraft geometry. A general methodology was developed and implemented and sample computer codes applied to prototype the proposed process. Studies utilizing this radar cross section tool were subsequently performed to demonstrate the capabilities of this method and show the impact that various inputs have on the outputs of these models. The F/A-18 aircraft configuration was chosen as a case study vehicle to perform a design space exercise and to investigate the relative impact of shaping parameters on radar cross section. Finally, two unique low observable configurations were analyzed to examine the impact of shaping for stealthiness.

Design and Numerical Simulation of Radial Inflow Turbine Volute

NASA Astrophysics Data System (ADS)

Shah, Samip P.; Channiwala, S. A.; Kulshreshtha, D. B.; Chaudhari, Gaurang

2014-12-01

The volute of a radial inflow turbine has to be designed to ensure that the desired rotor inlet conditions like absolute Mach number, flow angle etc. are attained. For the reasonable performance of vaneless volute turbine care has to be taken for reduction in losses at an appropriate flow angle at the rotor inlet, in the direction of volute, whose function is to convert gas energy into kinetic energy and direct the flow towards the rotor inlet at an appropriate flow angle with reduced losses. In literature it was found that the incompressible approaches failed to provide free vortex and uniform flow at rotor inlet for compressible flow regimes. So, this paper describes a non-dimensional design procedure for a vaneless turbine volute for compressible flow regime and investigates design parameters, such as the distribution of area ratio and radius ratio as a function of azimuth angle. The nondimensional design is converted in dimensional form for three different volute cross sections. A commercial computational fluid dynamics code is used to develop numerical models of three different volute cross sections. From the numerical models, losses generation in the different volutes are identified and compared. The maximum pressure loss coefficient for Trapezoidal cross section is 0.1075, for Bezier-trapezoidal cross section is 0.0677 and for circular cross section is 0.0438 near tongue region, which suggested that the circular cross section will give a better efficiency than other types of volute cross sections.

Numerical study of neutron beam divergence in a beam-fusion scenario employing laser driven ions

NASA Astrophysics Data System (ADS)

Alejo, A.; Green, A.; Ahmed, H.; Robinson, A. P. L.; Cerchez, M.; Clarke, R.; Doria, D.; Dorkings, S.; Fernandez, J.; McKenna, P.; Mirfayzi, S. R.; Naughton, K.; Neely, D.; Norreys, P.; Peth, C.; Powell, H.; Ruiz, J. A.; Swain, J.; Willi, O.; Borghesi, M.; Kar, S.

2016-09-01

The most established route to create a laser-based neutron source is by employing laser accelerated, low atomic-number ions in fusion reactions. In addition to the high reaction cross-sections at moderate energies of the projectile ions, the anisotropy in neutron emission is another important feature of beam-fusion reactions. Using a simple numerical model based on neutron generation in a pitcher-catcher scenario, anisotropy in neutron emission was studied for the deuterium-deuterium fusion reaction. Simulation results are consistent with the narrow-divergence (∼ 70 ° full width at half maximum) neutron beam recently served in an experiment employing multi-MeV deuteron beams of narrow divergence (up to 30° FWHM, depending on the ion energy) accelerated by a sub-petawatt laser pulse from thin deuterated plastic foils via the Target Normal Sheath Acceleration mechanism. By varying the input ion beam parameters, simulations show that a further improvement in the neutron beam directionality (i.e. reduction in the beam divergence) can be obtained by increasing the projectile ion beam temperature and cut-off energy, as expected from interactions employing higher power lasers at upcoming facilities.

Transverse momentum resummation for dijet correlation in hadronic collisions

NASA Astrophysics Data System (ADS)

Sun, Peng; Yuan, C.-P.; Yuan, Feng

2015-11-01

We study transverse momentum resummation for the azimuthal angular correlation in dijet production in hadron collisions based on the Collins-Soper-Sterman formalism. The complete one-loop calculations are carried out in the collinear framework for the differential cross sections at low imbalance transverse momentum between the two jets. Important cross-checks are performed to demonstrate that the soft divergences are canceled out between different diagrams and, in particular, for those associated with the final state jets. The leading and subleading logarithms are identified. All order resummation is derived following the transverse momentum dependent factorization at this order. Its phenomenological applications are also presented.

The evolutionary stability of cross-sex, cross-trait genetic covariances.

PubMed

Gosden, Thomas P; Chenoweth, Stephen F

2014-06-01

Although knowledge of the selective agents behind the evolution of sexual dimorphism has advanced considerably in recent years, we still lack a clear understanding of the evolutionary durability of cross-sex genetic covariances that often constrain its evolution. We tested the relative stability of cross-sex genetic covariances for a suite of homologous contact pheromones of the fruit fly Drosophila serrata, along a latitudinal gradient where these traits have diverged in mean. Using a Bayesian framework, which allowed us to account for uncertainty in all parameter estimates, we compared divergence in the total amount and orientation of genetic variance across populations, finding divergence in orientation but not total variance. We then statistically compared orientation divergence of within-sex (G) to cross-sex (B) covariance matrices. In line with a previous theoretical prediction, we find that the cross-sex covariance matrix, B, is more variable than either within-sex G matrix. Decomposition of B matrices into their symmetrical and nonsymmetrical components revealed that instability is linked to the degree of asymmetry. We also find that the degree of asymmetry correlates with latitude suggesting a role for spatially varying natural selection in shaping genetic constraints on the evolution of sexual dimorphism. © 2014 The Author(s). Evolution © 2014 The Society for the Study of Evolution.

A design method for entrance sections of transonic wind tunnels with rectangular cross sections

NASA Technical Reports Server (NTRS)

Lionel, L.; Mcdevitt, J. B.

1975-01-01

A mathematical technique developed to design entrance sections for transonic or high-speed subsonic wind tunnels with rectangular cross sections is discribed. The transition from a circular cross-section setting chamber to a rectangular test section is accomplished smoothly so as not to introduce secondary flows (vortices or boundary-layer separation) into a uniform test stream. The results of static-pressure measurements in the transition region and of static and total-pressure surveys in the test section of a pilot model for a new facility at the Ames Research Center are presented.

Comparative Evaluation of Stress Distribution in Experimentally Designed Nickel-titanium Rotary Files with Varying Cross Sections: A Finite Element Analysis.

PubMed

Basheer Ahamed, Shadir Bughari; Vanajassun, Purushothaman Pranav; Rajkumar, Kothandaraman; Mahalaxmi, Sekar

2018-04-01

Single cross-sectional nickel-titanium (NiTi) rotary instruments during continuous rotations are subjected to constant and variable stresses depending on the canal anatomy. This study was intended to create 2 new experimental, theoretic single-file designs with combinations of triple U (TU), triangle (TR), and convex triangle (CT) cross sections and to compare their bending stresses in simulated root canals with a single cross-sectional instrument using finite element analysis. A 3-dimensional model of the simulated root canal with 45° curvature and NiTi files with 5 cross-sectional designs were created using Pro/ENGINEER Wildfire 4.0 software (PTC Inc, Needham, MA) and ANSYS software (version 17; ANSYS, Inc, Canonsburg, PA) for finite element analysis. The NiTi files of 3 groups had single cross-sectional shapes of CT, TR, and TU designs, and 2 experimental groups had a CT, TR, and TU (CTU) design and a TU, TR, and CT (UTC) design. The file was rotated in simulated root canals to analyze the bending stress, and the von Mises stress value for every file was recorded in MPa. Statistical analysis was performed using the Kruskal-Wallis test and the Bonferroni-adjusted Mann-Whitney test for multiple pair-wise comparison with a P value <.05 (95 %). The maximum bending stress of the rotary file was observed in the apical third of the CT design, whereas comparatively less stress was recorded in the CTU design. The TU and TR designs showed a similar stress pattern at the curvature, whereas the UTC design showed greater stress in the apical and middle thirds of the file in curved canals. All the file designs showed a statistically significant difference. The CTU designed instruments showed the least bending stress on a 45° angulated simulated root canal when compared with all the other tested designs. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

[Design of cross-sectional anatomical model focused on drainage pathways of paranasal sinuses].

PubMed

Zha, Y; Lv, W; Gao, Y L; Zhu, Z Z; Gao, Z Q

2018-05-01

Objective: To design and produce cross-sectional anatomical models of paranasal sinuses for the purpose of demonstrating drainage pathways of each nasal sinus for the young doctors. Method: We reconstructed the three-dimensional model of sinuses area based on CT scan data, and divided it into 5 thick cross-sectional anatomy models by 4 coronal plane，which cross middle points of agger nasi cell, ethmoid bulla, posterior ethmoid sinuses and sphenoid sinus respectively. Then a 3D printerwas used to make anatomical cross-sectional anatomical models. Result: Successfully produced a digital 3D printing cross-sectional models of paranasal sinuses. Sinus drainage pathways were observed on the models. Conclusion: The cross-sectional anatomical models made by us can exactly and intuitively demonstrate the ostia of each sinus cell and they can help the young doctors to understand and master the key anatomies and relationships which are important to the endoscopic sinus surgery. Copyright© by the Editorial Department of Journal of Clinical Otorhinolaryngology Head and Neck Surgery.

Nuclear Forensics and Radiochemistry: Cross Sections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rundberg, Robert S.

The neutron activation of components in a nuclear device can provide useful signatures of weapon design or sophistication. This lecture will cover some of the basics of neutron reaction cross sections. Nuclear reactor cross sections will also be presented to illustrate the complexity of convolving neutron energy spectra with nuclear excitation functions to calculate useful effective reactor cross sections. Deficiencies in the nuclear database will be discussed along with tools available at Los Alamos to provide new neutron cross section data.

Justification of the Shape of a Non-Circular Cross-Section for Drilling With a Roller Cutter

NASA Astrophysics Data System (ADS)

Buyalich, Gennady; Husnutdinov, Mikhail

2017-11-01

The parameters of the shape of non-circular cross-section affect not only the process of blasting, but also the design of the tool and the process of drilling as well. In the conditions of open-pit mining, it is reasonable to use a roller cutter to produce a non-circular cross-section of blasting holes. With regard to the roller cutter, the impact of the cross-section shape on the oscillations of the axial force arising upon its rotation is determined. It is determined that a polygonal shape with rounded comers of the borehole walls connections and their convex shape, which ensures a smaller range of the total axial force and the torque deflecting the bit from the axis of its rotation is the rational form of the non-circular cross-section of the borehole in terms of bit design. It has been shown that the ratio of the number of cutters to the number of borehole corners must be taken into account when justifying the shape of the cross-section, both from the point of view of the effectiveness of the explosion action and from the point of view of the rational design of the bit.

Cross-cultural estimation of the human generation interval for use in genetics-based population divergence studies.

PubMed

Fenner, Jack N

2005-10-01

The length of the human generation interval is a key parameter when using genetics to date population divergence events. However, no consensus exists regarding the generation interval length, and a wide variety of interval lengths have been used in recent studies. This makes comparison between studies difficult, and questions the accuracy of divergence date estimations. Recent genealogy-based research suggests that the male generation interval is substantially longer than the female interval, and that both are greater than the values commonly used in genetics studies. This study evaluates each of these hypotheses in a broader cross-cultural context, using data from both nation states and recent hunter-gatherer societies. Both hypotheses are supported by this study; therefore, revised estimates of male, female, and overall human generation interval lengths are proposed. The nearly universal, cross-cultural nature of the evidence justifies using these proposed estimates in Y-chromosomal, mitochondrial, and autosomal DNA-based population divergence studies.

Wave-driven winds from cool stars. I - Some effects of magnetic field geometry

NASA Technical Reports Server (NTRS)

Hartmann, L.; Macgregor, K. B.

1982-01-01

The wave-driven wind theory of Hartmann and MacGregor (1980) is extended to include effects due to non-radial divergence of the flow. Specifically, isothermal expansion within a flow tube whose cross-sectional area increases outward faster than the square of the radius near the stellar surface is considered. It is found that the qualitative conclusions of Hartmann and MacGregor concerning the physical properties of Alfven wave-driven winds are largely unaffected. In particular, mass fluxes of similar magnitude are obtained, and wave dissipation is still necessary to produce acceptably small terminal velocities. Increasingly divergent flow geometries generally lead to higher initial wind speeds and slightly lower terminal velocities. For some cases of extremely rapid flow tube divergence, steady supersonic wind solutions which extend to infinity with vanishing gas pressure cannot be obtained. In addition, departures from spherical symmetry can cause the relative Alfven wave amplitude delta-B/B to become approximately greater than 1 within several stellar radii of the base of the wind, suggesting that nonlinear processes may contribute to the wave dissipation required by the theory.

Icelandic Physical Therapists' Attitudes Toward Adoption of New Knowledge and Evidence-Based Practice: Cross-Sectional Web-Based Survey.

PubMed

Arnadottir, Solveig A; Gudjonsdottir, Bjorg

2016-11-01

A positive attitude toward evidence-based practice (EBP) has been identified as an important factor in the effectiveness of the dissemination and implementation of EBP in real-world settings. The objectives of this study were: (1) to describe dimensions of Icelandic physical therapists' attitudes toward the adoption of new knowledge and EBP and (2) to explore the association between attitudes and selected personal and environmental factors. This study was a cross-sectional, Web-based survey of the total population of full members of the Icelandic Physiotherapy Association. The Evidence-Based Practice Attitude Scale (EBPAS) was used to survey attitudes toward EBP; the total EBPAS and its 4 subscales (requirements, appeal, openness, and divergence) were included. Linear regression was used to explore the association between the EBPAS and selected background variables. The response rate was 39.5% (N=211). The total EBPAS and all of its subscales reflected physical therapists' positive attitudes toward the adoption of new knowledge and EBP. Multivariable analysis revealed that being a woman was associated with more positive attitudes, as measured by the total EBPAS and the requirements, openness, and divergence subscales. Physical therapists with postprofessional education were more positive, as measured by the EBPAS openness subscale, and those working with at least 10 other physical therapists demonstrated more positive attitudes on the total EBPAS and the openness subscale. Because this was a cross-sectional survey, no causal inferences can be made, and there may have been unmeasured confounding factors. Potential nonresponse bias limits generalizability. The results expand understanding of the phenomenon of attitudes toward EBP. They reveal potentially modifiable dimensions of attitudes and the associated characteristics of physical therapists and their work environments. The findings encourage investigation of the effectiveness of strategies aimed at influencing various dimensions of attitudes toward EBP. © 2016 American Physical Therapy Association.

Behaviour of Reinforced Concrete Columns of Various Cross-Sections Subjected to Fire

NASA Astrophysics Data System (ADS)

Balaji, Aneesha; Muhamed Luquman, K.; Nagarajan, Praveen; Madhavan Pillai, T. M.

2016-09-01

Fire resistance is one of the crucial design regulations which are now mandatory in most of the design codes. Therefore, a thorough knowledge of behaviour of structures exposed to fire is required in this aspect. Columns are the most vulnerable structural member to fire as it can be exposed to fire from all sides. However, the data available for fire resistant design for columns are limited. Hence the present work is focused on the effect of cross-sectional shape of column in fire resistance design. The various cross-sections considered are Square, Ell (L), Tee (T), and Plus (`+') shape. Also the effect of size and shape and distribution of steel reinforcement on fire resistance of columns is studied. As the procedure for determining fire resistance is not mentioned in Indian Standard code IS 456 (2000), the simplified method (500 °C isotherm method) recommended in EN 1992-1-2:2004 (E) (Eurocode 2) is adopted. The temperature profiles for various cross-sections are developed using finite element method and these profiles are used to predict fire resistance capability of compression members. The fire resistance based on both numerical and code based methods are evaluated and compared for various types of cross-section.

Contributions of divergent and nondivergent winds to the kinetic energy balance of a severe storm environment

NASA Technical Reports Server (NTRS)

Browning, P. A.; Fuelberg, H. E.

1983-01-01

Divergent and rotational components of the synoptic scale kinetic energy balance are presented using rawinsonde data at 3 and 6 h intervals from the Atmospheric Variability Experiment (AVE 4). Two intense thunderstorm complexes occurred during the period. Energy budgets are described for the entire computational region and for limited volumes that enclose and move with the convection. Although small in magnitude, the divergent wind component played an important role in the cross contour generation and horizontal flux divergence of kinetic energy. The importance of V sub D appears directly to the presence and intensity of convection within the area. Although K sub D usually comprised less than 10 percent of the total kinetic energy content within the storm environment, as much as 87 percent of the total horizontal flux divergence and 68 percent of the total cross contour generation was due to the divergent component in the upper atmosphere. Generation of kinetic energy by the divergent component appears to be a major factor in the creation of an upper level wind maximum on the poleward side of one of the complexes. A random error analysis is presented to assess confidence limits in the various energy parameters.

Metabolomics: A Window for Understanding Long Term Physical Consequences of Distrubed Sleep and Hypothalamic Pituitary Adrenal Function in Posttraumatic Stress

DTIC Science & Technology

2017-09-01

performed on pre -collected plasma samples from a study that had a two- group cross-sectional design in which main comparisons were with medically...controls. Approach Metabolomic analysis will be performed on pre -collected plasma samples from a study that had a two- group cross-sectional design in...disturbances, and health. Metabolomic analysis will be performed on pre -collected plasma samples from a study that had a two- group cross-sectional

Fine-Tuning Cross-Battery Assessment Procedures: After Follow-Up Testing, Use All Valid Scores, Cohesive or Not

ERIC Educational Resources Information Center

Schneider, W. Joel; Roman, Zachary

2018-01-01

We used data simulations to test whether composites consisting of cohesive subtest scores are more accurate than composites consisting of divergent subtest scores. We demonstrate that when multivariate normality holds, divergent and cohesive scores are equally accurate. Furthermore, excluding divergent scores results in biased estimates of…

A Driving Simulator Evaluation of Cross-Sectional Design Elements and the Resulting Driving Behaviors

DOT National Transportation Integrated Search

2017-09-01

This research explores the relationship between the cross-sectional design elements and the impact on selected driver attributes such as speed profiles and lateral positioning. In this experiment a traditional collector-type base roadway of 1.5 miles...

Internal Performance of Several Divergent-Shroud Ejector Nozzles with High Divergence Angles

NASA Technical Reports Server (NTRS)

Trout, Arthur M.; Papell, S. Stephen; Povolny, John H.

1957-01-01

Nine divergent-shroud ejector configurations were investigated to determine the effect of shroud divergence angle on ejector internal performance. Unheated dry air was used for both the primary and secondary flows. The decrease in the design-point thrust coefficient with increasing flow divergence angle (angle measured from primary exit to shroud exit) followed very closely a simple relation involving the cosine of the angle. This indicates that design-point thrust performance for divergent-shroud ejectors can be predicted with reasonable accuracy within the range investigated. The decrease in design-point thrust coefficient due to increasing the flow divergence engle from 120deg to 30deg (half-singles) was approximately 6 percent. Ejector air-handling characteristics and the primary-nozzle flow coefficient were not significantly affected by change in shroud divergence angle.

[Validation of the German version of the Oxford Elbow Score : A cross-sectional study].

PubMed

Marquardt, J; Schöttker-Königer, T; Schäfer, A

2016-08-01

Elbow complaints are complex problems leading to severe consequences for affected people and the healthcare system. The German version of the Oxford Elbow Score (OES) is the first German-speaking instrument that specifically measures elbow complaints from the patient's perspective and changes of their health status. The aim of this study is the validation of the German version of the OES. In this context the internal consistency and the construct validity were investigated. 59 patients with elbow complaints completed the German version of the OES, the DASH and the SF-36 in a cross-sectional study. The internal consistency was calculated with Cronbach's alpha coefficients. Spearman's correlation coefficients were used to confirm construct validity. Cronbach's alpha for pain, function and psychological subscales was 0.88, 0.81 and 0.90, respectively. The whole questionnaire presents a Cronbach's alpha value of 0.93. Convergent construct validity was confirmed with correlation coefficients containing values of -0.84, -0.77 and -0.82 compared to DASH and values ranging from 0.41 to 0.80 compared with the physical domains of the SF-36. The divergent construct validity presented values ranging from 0.07 to 0.20 with the SF-36 domains of "general health perception" and "mental health". The German OES is an internal consistent instrument with good convergent and divergent construct validity. Other aspects of the validity, the reliability and the responsiveness should be confirmed through further studies.

Supercritical flow characteristics at abrupt expansion structure

NASA Astrophysics Data System (ADS)

Lim, Jia Jun; Puay, How Tion; Zakaria, Nor Azazi

2017-10-01

When dealing with the design of a hydraulic structure, lateral expansion is often necessary for flow emerging at high velocity served as a cross-sectional transition. If the abrupt expansion structure is made to diverge rapidly, it will cause the major part of the flow fail to follow the boundaries. If the transition is too gradual, it will result in a waste of structural material. A preliminary study on the flow structure near the expansion and its relationship with flow parameter is carried out in this study. A two-dimensional depth-averaged model is developed to simulate the supercritical flow at the abrupt expansion structure. Constrained Interpolation Profile (CIP) scheme (which is of third order accuracy) is adopted in the numerical model. Results show that the flow structure and flow characteristics at the abrupt expansion can be reproduced numerically. The validation of numerical result is done against analytical studies. The result from numerical simulation showed good agreement with the analytical solution.

Local Deplanation Of Double Reinforced Beam Cross Section Under Bending

NASA Astrophysics Data System (ADS)

Baltov, Anguel; Yanakieva, Ana

2015-12-01

Bending of beams, double reinforced by means of thin composite layers, is considered in the study. Approximate numerical solution is proposed, considering transitional boundary areas, where smooth quadratic transition of the elasticity modulus and deformations take place. Deplanation of the cross section is also accounted for in the areas. Their thickness is found equalizing the total stiffness of the cross section and the layer stiffness. Deplanation of the cross section of the transitional area is determined via the longitudinal deformation in the reinforcing layer, accounting for the equilibrium between the internal and the external moment, generated by the longitudinal stresses in the cross section. A numerical example is given as an illustration demonstrating model's plausibility. The model allows the design and the calculation of recycled concrete beams double reinforced by means of thin layers. The approach is in agreement with modern design of nearly zero energy buildings (NZEB).

Consistency between cross-sectional and longitudinal SNP: blood lipid associations.

PubMed

Costanza, Michael C; Beer-Borst, Sigrid; James, Richard W; Gaspoz, Jean-Michel; Morabia, Alfredo

2012-02-01

Various studies have linked different genetic single nucleotide polymorphisms (SNPs) to different blood lipids (BL), but whether these "connections" were identified using cross-sectional or longitudinal (i.e., changes over time) designs has received little attention. Cross-sectional and longitudinal assessments of BL [total, high-, low-density lipoprotein cholesterol (TC, HDL, LDL), triglycerides (TG)] and non-genetic factors (body mass index, smoking, alcohol intake) were measured for 2,002 Geneva, Switzerland, adults during 1999-2008 (two measurements, median 6 years apart), and 20 SNPs in 13 BL metabolism-related genes. Fixed and mixed effects repeated measures linear regression models, respectively, were employed to identify cross-sectional and longitudinal SNP:BL associations among the 1,516 (76%) study participants who reported not being treated for hypercholesterolemia at either measurement time. One-third more (12 vs. 9) longitudinal than cross-sectional associations were found [Bonferroni-adjusted two-tailed p < 0.00125 (=0.05/2)/20) for each of the four ensembles of 20 SNP:individual BL associations tested under the two study designs]. There was moderate consistency between the cross-sectional and longitudinal findings, with eight SNP:BL associations consistently identified across both study designs: [APOE.2 and APOE.4 (rs7412 and rs429358)]:TC; HL/LIPC (rs2070895):HDL; [APOB (rs1367117), APOE.2 and APOE.4 (rs7412 and rs429358)]:LDL; [APOA5 (rs2072560) and APOC III (rs5128)]:TG. The results suggest that cross-sectional studies, which include most genome-wide association studies (GWAS), can assess the large majority of SNP:BL associations. In the present analysis, which was much less powered than a GWAS, the cross-sectional study was around 2/3 (67%) as efficient as the longitudinal study.

Differential collision cross-sections for atomic oxygen: Analysis of space flight instruments for solar terrestrial physics

NASA Technical Reports Server (NTRS)

Torr, Douglas G.

1991-01-01

A summary of the status of the Cross-section Facility at MSFC is presented. A facility was designed, fabricated, assembled, tested, and operated for measurement of differential scattering cross sections important to understand the induced environment for a vehicle (e.g., Space Station) in low earth orbit. A user's manual for the facility is also presented. The performance of the facility was evaluated and found to be satisfactory in all the essential areas. Differential scattering cross sections were measured and results for the scattering measurements are included. Input to the development of the Ultraviolet Imager Optical System is also discussed. Design, fabrication, and evaluation of UV filters using a four-layer aluminum base are reported.

77 FR 47924 - Determinations Concerning Illnesses Discussed in National Academy of Sciences Report: Veterans...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-10

... significant increased prevalence of hypertension. The cross-sectional design of this study (in which subjects.... This study was also cross-sectional in design, limiting its ability to quantify risk, establish a... for significant confounders or by other methodological concerns. Accordingly, [[Page 47927

The Performance of a Subsonic Diffuser Designed for High Speed Turbojet-Propelled Flight

NASA Technical Reports Server (NTRS)

Biesiadny, Thomas J. (Technical Monitor); Wendt, Bruce J.

2004-01-01

An initial-phase subsonic diffuser has been designed for the turbojet flowpath of the hypersonic x43B flight demonstrator vehicle. The diffuser fit into a proposed mixed-compression supersonic inlet system and featured a cross-sectional shape transitioning flowpath (high aspect ratio rectangular throat-to-circular engine face) and a centerline offset. This subsonic diffuser has been fabricated and tested at the W1B internal flow facility at NASA Glenn Research Center. At an operating throat Mach number of 0.79, baseline Pitot pressure recovery was found to be just under 0.9, and DH distortion intensity was about 0.4 percent. The diffuser internal flow stagnated, but did not separate on the offset surface of this initial-phase subsonic diffuser. Small improvements in recovery (+0.4 percent) and DH distortion (-32 percent) were obtained from using vane vortex generator flow control applied just downstream of the diffuser throat. The optimum vortex generator array patterns produced inflow boundary layer divergence (local downwash) on the offset surface centerline of the diffuser, and an inflow boundary layer convergence (local upwash) on the centerline of the opposite surface.

Methodology for safety optimization of highway cross-sections for horizontal curves with restricted sight distance.

PubMed

Ibrahim, Shewkar E; Sayed, Tarek; Ismail, Karim

2012-11-01

Several earlier studies have noted the shortcomings with existing geometric design guides which provide deterministic standards. In these standards the safety margin of the design output is generally unknown and there is little knowledge of the safety implications of deviating from the standards. To mitigate these shortcomings, probabilistic geometric design has been advocated where reliability analysis can be used to account for the uncertainty in the design parameters and to provide a mechanism for risk measurement to evaluate the safety impact of deviations from design standards. This paper applies reliability analysis for optimizing the safety of highway cross-sections. The paper presents an original methodology to select a suitable combination of cross-section elements with restricted sight distance to result in reduced collisions and consistent risk levels. The purpose of this optimization method is to provide designers with a proactive approach to the design of cross-section elements in order to (i) minimize the risk associated with restricted sight distance, (ii) balance the risk across the two carriageways of the highway, and (iii) reduce the expected collision frequency. A case study involving nine cross-sections that are parts of two major highway developments in British Columbia, Canada, was presented. The results showed that an additional reduction in collisions can be realized by incorporating the reliability component, P(nc) (denoting the probability of non-compliance), in the optimization process. The proposed approach results in reduced and consistent risk levels for both travel directions in addition to further collision reductions. Copyright © 2012 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chakrabarti, D.; Qiu, J.; Thorn, C. B.

This is the second of a pair of articles on scattering of glue by glue,in which we give the light-cone gauge calculation of the one-loop on-shellhelicity conserving scattering amplitudes for gluon-gluon scattering (neglectingquark loops). The 1/p{sup +} factors in the gluon propagatorare regulated by replacing p{sup +} integrals with discretized sums omitting the p{sup +}=0 terms in each sum. We alsoemploy a novel ultraviolet regulator that is convenient for the light-coneworldsheet description of planar Feynman diagrams. The helicity conservingscattering amplitudes are divergent in the infrared. The infrared divergencesin the elastic one-loop amplitude are shown to cancel, in their contributionto crossmore » sections, against ones in the cross section for unseen bremsstrahlunggluons. We include here the explicit calculation of the latter, because itassumes an unfamiliar form due to the peculiar way discretization of p{sup +} regulates infrared divergences. In resolving the infrareddivergences we employ a covariant definition of jets, which allows a transparentdemonstration of the Lorentz invariance of our final results. Because we usean explicit cutoff of the ultraviolet divergences in exactly four spacetimedimensions, we must introduce explicit counterterms to achieve this finalcovariant result. These counterterms are polynomials in the external momentaof the precise order dictated by power counting. We discuss the modificationsthey entail for the light-cone worldsheet action that reproduces the bareplanar diagrams of the gluonic sector of QCD. The simplest way to do thisis to interpret the QCD string as moving in six spacetime dimensions.« less

Comparison of gimbal approaches to decrease drag force and radar cross sectional area in missile application

NASA Astrophysics Data System (ADS)

Sakarya, Doǧan Uǧur

2017-05-01

Drag force effect is an important aspect of range performance in missile applications especially for long flight time. However, old fashioned gimbal approaches force to increase missile diameter. This increase has negative aspect of rising in both drag force and radar cross sectional area. A new gimbal approach was proposed recently. It uses a beam steering optical arrangement. Therefore, it needs less volume envelope for same field of regard and same optomechanical assembly than the old fashioned gimbal approaches. In addition to longer range performance achieved with same fuel in the new gimbal approach, this method provides smaller cross sectional area which can be more invisible in enemies' radar. In this paper, the two gimbal approaches - the old fashioned one and the new one- are compared in order to decrease drag force and radar cross sectional area in missile application. In this study; missile parameters are assumed to generate gimbal and optical design parameters. Optical design is performed according to these missile criteria. Two gimbal configurations are designed with respect to modeled missile parameters. Also analyzes are performed to show decreased drag force and radar cross sectional area in the new approach for comparison.

An evaluation of three helicopter rotor sections

NASA Technical Reports Server (NTRS)

Hicks, R. M.; Collins, L. J.

1985-01-01

Three helicopter rotor sections were tested in the NASA Ames Research Center 2- by 2-Foot Transonic Wind Tunnel over a Mach range from 0.2 to 0.88. The sections tested had maximum thickness/chord ratios of 0.078, 0.09, and 0.10. The thickest section was of early technology and had been tested previously in other wind tunnels. This section was included in the investigation to establish a basis for comparing the two thinner sections, which were of recent design. The results of the investigation showed that the pitching-moment characteristics for the three airfoil sections were acceptable. The drag divergence Mach numbers for the three sections were 0.80, 0.825, and 0.845 in order of decreasing thickness.

Design and analytical study of a rotor airfoil

NASA Technical Reports Server (NTRS)

Dadone, L. U.

1978-01-01

An airfoil section for use on helicopter rotor blades was defined and analyzed by means of potential flow/boundary layer interaction and viscous transonic flow methods to meet as closely as possible a set of advanced airfoil design objectives. The design efforts showed that the first priority objectives, including selected low speed pitching moment, maximum lift and drag divergence requirements can be met, though marginally. The maximum lift requirement at M = 0.5 and most of the profile drag objectives cannot be met without some compromise of at least one of the higher order priorities.

Cross-reactivity between avian influenza A (H7N9) virus and divergent H7 subtypic- and heterosubtypic influenza A viruses

PubMed Central

Guo, Li; Wang, Dayan; Zhou, Hongli; Wu, Chao; Gao, Xin; Xiao, Yan; Ren, Lili; Paranhos-Baccalà, Gláucia; Shu, Yuelong; Jin, Qi; Wang, Jianwei

2016-01-01

The number of human avian H7N9 influenza infections has been increasing in China. Understanding their antigenic and serologic relationships is crucial for developing diagnostic tools and vaccines. Here, we evaluated the cross-reactivities and neutralizing activities among H7 subtype influenza viruses and between H7N9 and heterosubtype influenza A viruses. We found strong cross-reactivities between H7N9 and divergent H7 subtypic viruses, including H7N2, H7N3, and H7N7. Antisera against H7N2, H7N3, and H7N7 could also effectively neutralize two distinct H7N9 strains. Two-way cross-reactivities exist within group 2, including H3 and H4, whereas one-way cross-reactivities were found across other groups, including H1, H10, H9, and H13. Our data indicate that the hemaglutinins from divergent H7 subtypes may facilitate the development of vaccines for distinct H7N9 infections. Moreover, serologic diagnoses for H7N9 infections need to consider possible interference from the cross-reactivity of H7N9 with other subtype influenza viruses. PMID:26907865

Cross-reactivity between avian influenza A (H7N9) virus and divergent H7 subtypic- and heterosubtypic influenza A viruses.

PubMed

Guo, Li; Wang, Dayan; Zhou, Hongli; Wu, Chao; Gao, Xin; Xiao, Yan; Ren, Lili; Paranhos-Baccalà, Gláucia; Shu, Yuelong; Jin, Qi; Wang, Jianwei

2016-02-24

The number of human avian H7N9 influenza infections has been increasing in China. Understanding their antigenic and serologic relationships is crucial for developing diagnostic tools and vaccines. Here, we evaluated the cross-reactivities and neutralizing activities among H7 subtype influenza viruses and between H7N9 and heterosubtype influenza A viruses. We found strong cross-reactivities between H7N9 and divergent H7 subtypic viruses, including H7N2, H7N3, and H7N7. Antisera against H7N2, H7N3, and H7N7 could also effectively neutralize two distinct H7N9 strains. Two-way cross-reactivities exist within group 2, including H3 and H4, whereas one-way cross-reactivities were found across other groups, including H1, H10, H9, and H13. Our data indicate that the hemaglutinins from divergent H7 subtypes may facilitate the development of vaccines for distinct H7N9 infections. Moreover, serologic diagnoses for H7N9 infections need to consider possible interference from the cross-reactivity of H7N9 with other subtype influenza viruses.

Applications and Engineering Analysis of Lotus Roots under External Water Pressure

PubMed Central

Wang, Chang Jiang; Mynors, Diane

2016-01-01

Engineers can learn from nature for inspirations to create new designs. The internal structure of lotus roots with several oval holes was studied in this paper for engineering inspirations. The structural performance of lotus roots under outside water pressure was simulated and compared with various cross-sectional areas. The distribution of stresses in the cross-sectional area of lotus roots was analysed and presented. It was found that the maximum compressive stresses in the cross-sectional area of lotus roots were occurring at the long axis ends of the holes. This was very different from that of circular holes. Further analysis on the triaxiality factors revealed that the cross-sectional area of the lotus root resulted in large areas of high triaxiality factors. The resulting hydrostatic stress in the cross-sectional area of lotus root ranges from zero to 2.7 times the applied outside pressure. In contrast, the hydrostatic stress in a cylindrical cross-sectional area is a fixed value. The study showed that the lotus root and the orientation of the oval holes could be mimicked in the design of new structures, for example, underwater pipes and vessels. PMID:28127228

Divergence analysis report for the bodies of revolution model support systems

NASA Technical Reports Server (NTRS)

Rash, Larry C.

1983-01-01

This report documents the sting divergence analyses of nine different model and model support systems that were performed in preparation for a series of wind tunnel tests at the National Transonic Facility at NASA Langley Research Center in Hampton, Virginia. The models were missile shaped bodies of revolution and the model support systems included a force and moment balance and tapered sting sections. The sting divergence results were obtained from a computer program that solved a two-point boundary value problem which used a second order Runge-Kutta integration technique. The computer solution was based on constant section properties between discrete stations along the sting sections, a procedure was developed and included to evaluate the properties for the minimum number of stations along the tapered sections that would produce no more than one half of one percent error in the divergence results. Also included in the report are development of the aerodynamic input data, listings of all input and output computer data, and summary sheets that highlight the input and the critical sting divergence dynamic pressure for each respective configuration.

Dental Students' Educational Achievement in Relation to Their Learning Styles: A Cross-Sectional Study in Iran.

PubMed

Hosseini, Seyed Masoud; Amery, Hamideh; Emadzadeh, Ali; Babazadeh, Saber

2015-02-24

In recent decades, many studies have been carried out on the importance of Kolb experiential learning theory (ELT) in teaching-learning processes and its effect on learning outcomes. However, some experts have criticized the Kolb theory and argue that there are some ambiguities on the validity of the theory as an important predictor of achievement. This study has been carried out on dental students' educational achievement in relation to their dominant learning styles based on Kolb theory in Mashhad University of Medical Sciences (Iran). In a cross sectional study, Kolb Learning Style Inventory (LSI Ver. 3.1) as well as a questionnaire containing students' demographic data, academic achievement marks including grade point average (GPA), theoretical and practical courses marks, and the comprehensive basic sciences exam (CBSE) scores were administered on a purposive sample of 162 dental students who had passed their comprehensive basic sciences exam. Educational achievement data were analyzed in relation to students' dominant learning styles, using descriptive and analytical statistics including χ2, Kruskal-Wallis and two-way ANOVA tests. The dominant learning styles of students were Assimilating (53.1%), Converging (24.1%), Diverging (14.2%) and Accommodating (8.6%). Although, the students with Assimilating and Converging learning styles had a better performance on their educational achievement, there was no significant relationship between educational achievement and dominant learning style (P≥0.05). Findings support that the dominant learning style is not exclusively an essential factor to predict educational achievement. Rather, it shows learning preferences of students that may be considered in designing learning opportunities by the teachers.

Exploring Structural Dynamics within and between Sensory and Intellectual Functioning in Old and Very Old Age: Longitudinal Evidence from the Berlin Aging Study

ERIC Educational Resources Information Center

Ghisletta, Paolo; Lindenberger, Ulman

2005-01-01

Cross-sectional and longitudinal analyses of age-heterogeneous samples have revealed correlational links between and within intellectual, sensory, and sensorimotor domains. Due to basic limitations of cross-sectional designs and a reluctance to disentangle antecedent-consequent relations in longitudinal designs, the functional significance and…

A time projection chamber for high accuracy and precision fission cross-section measurements

DOE PAGES

Heffner, M.; Asner, D. M.; Baker, R. G.; ...

2014-05-22

The fission Time Projection Chamber (fissionTPC) is a compact (15 cm diameter) two-chamber MICROMEGAS TPC designed to make precision cross-section measurements of neutron-induced fission. The actinide targets are placed on the central cathode and irradiated with a neutron beam that passes axially through the TPC inducing fission in the target. The 4π acceptance for fission fragments and complete charged particle track reconstruction are powerful features of the fissionTPC which will be used to measure fission cross-sections and examine the associated systematic errors. This study provides a detailed description of the design requirements, the design solutions, and the initial performance ofmore » the fissionTPC.« less

Child obesity cut-offs as derived from parental perceptions: cross-sectional questionnaire.

PubMed

Black, James A; Park, MinHae; Gregson, John; Falconer, Catherine L; White, Billy; Kessel, Anthony S; Saxena, Sonia; Viner, Russell M; Kinra, Sanjay

2015-04-01

Overweight children are at an increased risk of premature mortality and disease in adulthood. Parental perceptions and clinical definitions of child obesity differ, which may lessen the effectiveness of interventions to address obesity in the home setting. The extent to which parental and objective weight status cut-offs diverge has not been documented. To compare parental perceived and objectively derived assessment of underweight, healthy weight, and overweight in English children, and to identify sociodemographic characteristics that predict parental under- or overestimation of a child's weight status. Cross-sectional questionnaire completed by parents linked with objective measurement of height and weight by school nurses, in English children from five regions aged 4-5 and 10-11 years old. Parental derived cut-offs for under- and overweight were derived from a multinomial model of parental classification of their own child's weight status against school nurse measured body mass index (BMI) centile. Measured BMI centile was matched with parent classification of weight status in 2976 children. Parents become more likely to classify their children as underweight when they are at the 0.8th centile or below, and overweight at the 99.7th centile or above. Parents were more likely to underestimate a child's weight if the child was black or South Asian, male, more deprived, or the child was older. These values differ greatly from the BMI centile cut-offs for underweight (2nd centile) and overweight (85th). Clinical and parental classifications of obesity are divergent at extremes of the weight spectrum. © British Journal of General Practice 2015.

Multiplex Degenerate Primer Design for Targeted Whole Genome Amplification of Many Viral Genomes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gardner, Shea N.; Jaing, Crystal J.; Elsheikh, Maher M.

Background . Targeted enrichment improves coverage of highly mutable viruses at low concentration in complex samples. Degenerate primers that anneal to conserved regions can facilitate amplification of divergent, low concentration variants, even when the strain present is unknown. Results . A tool for designing multiplex sets of degenerate sequencing primers to tile overlapping amplicons across multiple whole genomes is described. The new script, run_tiled_primers, is part of the PriMux software. Primers were designed for each segment of South American hemorrhagic fever viruses, tick-borne encephalitis, Henipaviruses, Arenaviruses, Filoviruses, Crimean-Congo hemorrhagic fever virus, Rift Valley fever virus, and Japanese encephalitis virus. Eachmore » group is highly diverse with as little as 5% genome consensus. Primer sets were computationally checked for nontarget cross reactions against the NCBI nucleotide sequence database. Primers for murine hepatitis virus were demonstrated in the lab to specifically amplify selected genes from a laboratory cultured strain that had undergone extensive passage in vitro and in vivo. Conclusions . This software should help researchers design multiplex sets of primers for targeted whole genome enrichment prior to sequencing to obtain better coverage of low titer, divergent viruses. Applications include viral discovery from a complex background and improved sensitivity and coverage of rapidly evolving strains or variants in a gene family.« less

Multiplex Degenerate Primer Design for Targeted Whole Genome Amplification of Many Viral Genomes

DOE PAGES

Gardner, Shea N.; Jaing, Crystal J.; Elsheikh, Maher M.; ...

2014-01-01

Background . Targeted enrichment improves coverage of highly mutable viruses at low concentration in complex samples. Degenerate primers that anneal to conserved regions can facilitate amplification of divergent, low concentration variants, even when the strain present is unknown. Results . A tool for designing multiplex sets of degenerate sequencing primers to tile overlapping amplicons across multiple whole genomes is described. The new script, run_tiled_primers, is part of the PriMux software. Primers were designed for each segment of South American hemorrhagic fever viruses, tick-borne encephalitis, Henipaviruses, Arenaviruses, Filoviruses, Crimean-Congo hemorrhagic fever virus, Rift Valley fever virus, and Japanese encephalitis virus. Eachmore » group is highly diverse with as little as 5% genome consensus. Primer sets were computationally checked for nontarget cross reactions against the NCBI nucleotide sequence database. Primers for murine hepatitis virus were demonstrated in the lab to specifically amplify selected genes from a laboratory cultured strain that had undergone extensive passage in vitro and in vivo. Conclusions . This software should help researchers design multiplex sets of primers for targeted whole genome enrichment prior to sequencing to obtain better coverage of low titer, divergent viruses. Applications include viral discovery from a complex background and improved sensitivity and coverage of rapidly evolving strains or variants in a gene family.« less

Total reaction cross sections in CEM and MCNP6 at intermediate energies

DOE PAGES

Kerby, Leslie M.; Mashnik, Stepan G.

2015-05-14

Accurate total reaction cross section models are important to achieving reliable predictions from spallation and transport codes. The latest version of the Cascade Exciton Model (CEM) as incorporated in the code CEM03.03, and the Monte Carlo N-Particle transport code (MCNP6), both developed at Los Alamos National Laboratory (LANL), each use such cross sections. Having accurate total reaction cross section models in the intermediate energy region (50 MeV to 5 GeV) is very important for different applications, including analysis of space environments, use in medical physics, and accelerator design, to name just a few. The current inverse cross sections used inmore » the preequilibrium and evaporation stages of CEM are based on the Dostrovsky et al. model, published in 1959. Better cross section models are now available. Implementing better cross section models in CEM and MCNP6 should yield improved predictions for particle spectra and total production cross sections, among other results.« less

Total reaction cross sections in CEM and MCNP6 at intermediate energies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kerby, Leslie M.; Mashnik, Stepan G.

Accurate total reaction cross section models are important to achieving reliable predictions from spallation and transport codes. The latest version of the Cascade Exciton Model (CEM) as incorporated in the code CEM03.03, and the Monte Carlo N-Particle transport code (MCNP6), both developed at Los Alamos National Laboratory (LANL), each use such cross sections. Having accurate total reaction cross section models in the intermediate energy region (50 MeV to 5 GeV) is very important for different applications, including analysis of space environments, use in medical physics, and accelerator design, to name just a few. The current inverse cross sections used inmore » the preequilibrium and evaporation stages of CEM are based on the Dostrovsky et al. model, published in 1959. Better cross section models are now available. Implementing better cross section models in CEM and MCNP6 should yield improved predictions for particle spectra and total production cross sections, among other results.« less

Axisymmetric electrostatic magnetohydrodynamic oscillations in tokamaks with general cross-sections and toroidal flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, M. S.; Guo, Wenfeng

2016-06-15

The frequency spectrum and mode structure of axisymmetric electrostatic oscillations [the zonal flow (ZF), sound waves (SW), geodesic acoustic modes (GAM), and electrostatic mean flows (EMF)] in tokamaks with general cross-sections and toroidal flows are studied analytically using the electrostatic approximation for magnetohydrodynamic modes. These modes constitute the “electrostatic continua.” Starting from the energy principle for a tokamak plasma with toroidal rotation, we showed that these modes are completely stable. The ZF, the SW, and the EMF could all be viewed as special cases of the general GAM. The Euler equations for the general GAM are obtained and are solvedmore » analytically for both the low and high range of Mach numbers. The solution consists of the usual countable infinite set of eigen-modes with discrete eigen-frequencies, and two modes with lower frequencies. The countable infinite set is identified with the regular GAM. The lower frequency mode, which is also divergence free as the plasma rotation tends to zero, is identified as the ZF. The other lower (zero) frequency mode is a pure geodesic E×B flow and not divergence free is identified as the EMF. The frequency of the EMF is shown to be exactly 0 independent of plasma cross-section or its flow Mach number. We also show that in general, sound waves with no geodesic components are (almost) completely lost in tokamaks with a general cross-sectional shape. The exception is the special case of strict up-down symmetry. In this case, half of the GAMs would have no geodesic displacements. They are identified as the SW. Present day tokamaks, although not strictly up-down symmetric, usually are only slightly up-down asymmetric. They are expected to share the property with the up-down symmetric tokamak in that half of the GAMs would be more sound wave-like, i.e., have much weaker coupling to the geodesic components than the other half of non-sound-wave-like modes with stronger coupling to the geodesic displacements. Based on the general notion that the geodesic component of the GAM is more effective in tearing up the eddies in the electrostatic turbulence, it is important to preferentially excite the GAMs that are non-sound-wave like to maximize the efficiency on turbulence suppression through external means. Finally, approximate formulae for the frequencies of the EMF, ZF, SW, and the GAM for a large aspect ratio circular tokamak rotating at low Mach numbers are also provided.« less

Intercultural Sourcebook: Cross-Cultural Training Methods. Volume 2.

ERIC Educational Resources Information Center

Fowler, Sandra M., Ed.; Mumford, Monica G., Ed.

This comprehensive collection of training methods and exercises used by top trainers in the cross-cultural field contains resources essential for cross-cultural learning. This second volume of the collection includes articles by 34 leading cross-cultural trainers and covers new or divergent training methods for cross-cultural skill development and…

Linkographic Evidence for Concurrent Divergent and Convergent Thinking in Creative Design

ERIC Educational Resources Information Center

Goldschmidt, Gabriela

2016-01-01

For a long time, the creativity literature has stressed the role of divergent thinking in creative endeavor. More recently, it has been recognized that convergent thinking also has a role in creativity, and the design literature, which sees design as a creative activity a priori, has largely adopted this view: Divergent and convergent thinking are…

Simple, empirical approach to predict neutron capture cross sections from nuclear masses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couture, Aaron Joseph; Casten, Richard F.; Cakirli, R. B.

Here, neutron capture cross sections are essential to understanding the astrophysical s and r processes, the modeling of nuclear reactor design and performance, and for a wide variety of nuclear forensics applications. Often, cross sections are needed for nuclei where experimental measurements are difficult. Enormous effort, over many decades, has gone into attempting to develop sophisticated statistical reaction models to predict these cross sections. Such work has met with some success but is often unable to reproduce measured cross sections to better than 40%, and has limited predictive power, with predictions from different models rapidly differing by an order ofmore » magnitude a few nucleons from the last measurement.« less

Simple, empirical approach to predict neutron capture cross sections from nuclear masses

DOE PAGES

Couture, Aaron Joseph; Casten, Richard F.; Cakirli, R. B.

2017-12-20

Here, neutron capture cross sections are essential to understanding the astrophysical s and r processes, the modeling of nuclear reactor design and performance, and for a wide variety of nuclear forensics applications. Often, cross sections are needed for nuclei where experimental measurements are difficult. Enormous effort, over many decades, has gone into attempting to develop sophisticated statistical reaction models to predict these cross sections. Such work has met with some success but is often unable to reproduce measured cross sections to better than 40%, and has limited predictive power, with predictions from different models rapidly differing by an order ofmore » magnitude a few nucleons from the last measurement.« less

Roadway median treatments : phase 1 and phase 2.

DOT National Transportation Integrated Search

2010-02-01

This research project examined relationships among crash rates, cross section design elements, and other operational attributes of multilane urban and suburban roadways in Arkansas. Crash rates for four cross section categories (roadways with no medi...

Bistatic and Multistatic Radar: Surveillance, Countermeasures, and Radar Cross Sections. (Latest citations from the Aerospace Database)

NASA Technical Reports Server (NTRS)

1998-01-01

The bibliography contains citations concerning the design, development, testing, and evaluation of bistatic and multistatic radar used in surveillance and countermeasure technology. Citations discuss radar cross sections, target recognition and characteristics, ghost recognition, motion image compensation, and wavelet analysis. Stealth aircraft design, stealth target tracking, synthetic aperture radar, and space applications are examined.

Bistatic and Multistatic Radar: Surveillance, Countermeasures, and Radar Cross Sections. (Latest Citations from the Aerospace Database)

NASA Technical Reports Server (NTRS)

1997-01-01

The bibliography contains citations concerning the design, development, testing, and evaluation of bistatic and multistatic radar used in surveillance and countermeasure technology. Citations discuss radar cross sections, target recognition and characteristics, ghost recognition, motion image compensation, and wavelet analysis. Stealth aircraft design, stealth target tracking, synthetic aperture radar, and space applications are examined.

Development of ORIGEN Libraries for Mixed Oxide (MOX) Fuel Assembly Designs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mertyurek, Ugur; Gauld, Ian C.

In this research, ORIGEN cross section libraries for reactor-grade mixed oxide (MOX) fuel assembly designs have been developed to provide fast and accurate depletion calculations to predict nuclide inventories, radiation sources and thermal decay heat information needed in safety evaluations and safeguards verification measurements of spent nuclear fuel. These ORIGEN libraries are generated using two-dimensional lattice physics assembly models that include enrichment zoning and cross section data based on ENDF/B-VII.0 evaluations. Using the SCALE depletion sequence, burnup-dependent cross sections are created for selected commercial reactor assembly designs and a representative range of reactor operating conditions, fuel enrichments, and fuel burnup.more » The burnup dependent cross sections are then interpolated to provide problem-dependent cross sections for ORIGEN, avoiding the need for time-consuming lattice physics calculations. The ORIGEN libraries for MOX assembly designs are validated against destructive radiochemical assay measurements of MOX fuel from the MALIBU international experimental program. This program included measurements of MOX fuel from a 15 × 15 pressurized water reactor assembly and a 9 × 9 boiling water reactor assembly. The ORIGEN MOX libraries are also compared against detailed assembly calculations from the Phase IV-B numerical MOX fuel burnup credit benchmark coordinated by the Nuclear Energy Agency within the Organization for Economic Cooperation and Development. Finally, the nuclide compositions calculated by ORIGEN using the MOX libraries are shown to be in good agreement with other physics codes and with experimental data.« less

Development of ORIGEN Libraries for Mixed Oxide (MOX) Fuel Assembly Designs

DOE PAGES

Mertyurek, Ugur; Gauld, Ian C.

2015-12-24

In this research, ORIGEN cross section libraries for reactor-grade mixed oxide (MOX) fuel assembly designs have been developed to provide fast and accurate depletion calculations to predict nuclide inventories, radiation sources and thermal decay heat information needed in safety evaluations and safeguards verification measurements of spent nuclear fuel. These ORIGEN libraries are generated using two-dimensional lattice physics assembly models that include enrichment zoning and cross section data based on ENDF/B-VII.0 evaluations. Using the SCALE depletion sequence, burnup-dependent cross sections are created for selected commercial reactor assembly designs and a representative range of reactor operating conditions, fuel enrichments, and fuel burnup.more » The burnup dependent cross sections are then interpolated to provide problem-dependent cross sections for ORIGEN, avoiding the need for time-consuming lattice physics calculations. The ORIGEN libraries for MOX assembly designs are validated against destructive radiochemical assay measurements of MOX fuel from the MALIBU international experimental program. This program included measurements of MOX fuel from a 15 × 15 pressurized water reactor assembly and a 9 × 9 boiling water reactor assembly. The ORIGEN MOX libraries are also compared against detailed assembly calculations from the Phase IV-B numerical MOX fuel burnup credit benchmark coordinated by the Nuclear Energy Agency within the Organization for Economic Cooperation and Development. Finally, the nuclide compositions calculated by ORIGEN using the MOX libraries are shown to be in good agreement with other physics codes and with experimental data.« less

Two-phase flow pressure drop and heat transfer during condensation in microchannels with uniform and converging cross-sections

NASA Astrophysics Data System (ADS)

Kuo, Ching Yi; Pan, Chin

2010-09-01

This study experimentally investigates steam condensation in rectangular microchannels with uniform and converging cross-sections and a mean hydraulic diameter of 135 µm. The steam flow in the microchannels was cooled by water cross-flowing along its bottom surface, which is different from other methods reported in the literature. The flow patterns, two-phase flow pressure drop and condensation heat transfer coefficient are determined. The microchannels with the uniform cross-section design have a higher heat transfer coefficient than those with the converging cross-section under condensation in the mist/annular flow regimes, although the latter work best for draining two-phase fluids composed of uncondensed steam and liquid water, which is consistent with the result of our previous study. From the experimental results, dimensionless correlations of condensation heat transfer for the mist and annular flow regions and a two-phase frictional multiplier are developed for the microchannels with both types of cross-section designs. The experimental data agree well with the obtained correlations, with the maximum mean absolute errors of 6.4% for the two-phase frictional multiplier and 6.0% for the condensation heat transfer.

Augmented Cross-Sectional Studies with Abbreviated Follow-up for Estimating HIV Incidence

PubMed Central

Claggett, B.; Lagakos, S.W.; Wang, R.

2011-01-01

Summary Cross-sectional HIV incidence estimation based on a sensitive and less-sensitive test offers great advantages over the traditional cohort study. However, its use has been limited due to concerns about the false negative rate of the less-sensitive test, reflecting the phenomenon that some subjects may remain negative permanently on the less-sensitive test. Wang and Lagakos (2010) propose an augmented cross-sectional design which provides one way to estimate the size of the infected population who remain negative permanently and subsequently incorporate this information in the cross-sectional incidence estimator. In an augmented cross-sectional study, subjects who test negative on the less-sensitive test in the cross-sectional survey are followed forward for transition into the nonrecent state, at which time they would test positive on the less-sensitive test. However, considerable uncertainty exists regarding the appropriate length of follow-up and the size of the infected population who remain nonreactive permanently to the less-sensitive test. In this paper, we assess the impact of varying follow-up time on the resulting incidence estimators from an augmented cross-sectional study, evaluate the robustness of cross-sectional estimators to assumptions about the existence and the size of the subpopulation who will remain negative permanently, and propose a new estimator based on abbreviated follow-up time (AF). Compared to the original estimator from an augmented cross-sectional study, the AF Estimator allows shorter follow-up time and does not require estimation of the mean window period, defined as the average time between detectability of HIV infection with the sensitive and less-sensitive tests. It is shown to perform well in a wide range of settings. We discuss when the AF Estimator would be expected to perform well and offer design considerations for an augmented cross-sectional study with abbreviated follow-up. PMID:21668904

Augmented cross-sectional studies with abbreviated follow-up for estimating HIV incidence.

PubMed

Claggett, B; Lagakos, S W; Wang, R

2012-03-01

Cross-sectional HIV incidence estimation based on a sensitive and less-sensitive test offers great advantages over the traditional cohort study. However, its use has been limited due to concerns about the false negative rate of the less-sensitive test, reflecting the phenomenon that some subjects may remain negative permanently on the less-sensitive test. Wang and Lagakos (2010, Biometrics 66, 864-874) propose an augmented cross-sectional design that provides one way to estimate the size of the infected population who remain negative permanently and subsequently incorporate this information in the cross-sectional incidence estimator. In an augmented cross-sectional study, subjects who test negative on the less-sensitive test in the cross-sectional survey are followed forward for transition into the nonrecent state, at which time they would test positive on the less-sensitive test. However, considerable uncertainty exists regarding the appropriate length of follow-up and the size of the infected population who remain nonreactive permanently to the less-sensitive test. In this article, we assess the impact of varying follow-up time on the resulting incidence estimators from an augmented cross-sectional study, evaluate the robustness of cross-sectional estimators to assumptions about the existence and the size of the subpopulation who will remain negative permanently, and propose a new estimator based on abbreviated follow-up time (AF). Compared to the original estimator from an augmented cross-sectional study, the AF estimator allows shorter follow-up time and does not require estimation of the mean window period, defined as the average time between detectability of HIV infection with the sensitive and less-sensitive tests. It is shown to perform well in a wide range of settings. We discuss when the AF estimator would be expected to perform well and offer design considerations for an augmented cross-sectional study with abbreviated follow-up. © 2011, The International Biometric Society.

The Multidimensional Loss Scale: validating a cross-cultural instrument for measuring loss.

PubMed

Vromans, Lyn; Schweitzer, Robert D; Brough, Mark

2012-04-01

The Multidimensional Loss Scale (MLS) represents the first instrument designed specifically to index Experience of Loss Events and Loss Distress across multiple domains (cultural, social, material, and intrapersonal) relevant to refugee settlement. Recently settled Burmese adult refugees (N = 70) completed a questionnaire battery, including MLS items. Analyses explored MLS internal consistency, convergent and divergent validity, and factor structure. Cronbach alphas indicated satisfactory internal consistency for Experience of Loss Events (0.85) and Loss Distress (0.92), reflecting a unitary construct of multidimensional loss. Loss Distress did not correlate with depression or anxiety symptoms and correlated moderately with interpersonal grief and trauma symptoms, supporting divergent and convergent validity. Factor analysis provided preliminary support for a five-factor model: Loss of Symbolic Self, Loss of Interdependence, Loss of Home, Interpersonal Loss, and Loss of Intrapersonal Integrity. Received well by participants, the new scale shows promise for application in future research and practice.

Moisture processes accompanying convective activity

NASA Technical Reports Server (NTRS)

Sienkiewicz, M. E.; Scoggins, J. R.

1982-01-01

A moisture budget analysis was performed on data collected during the AVE 7 (May 2 to 3, 1978) and AVE-SESAME1 (April 10 to 11, 1979) experiments. Local rates-of-change of moisture were compared with average moisture divergence in the same time period. Results were presented as contoured plots in the horizontal and as vertical cross sections. These results were used to develop models of the distribution of moisture processes in the vicinity of convective areas in two layers representing lower and middle tropospheric conditions. Good correspondence was found between the residual term of the moisture budget and actual precipitation.

Validation of the kidney disease quality of life-short form: a cross-sectional study of a dialysis-targeted health measure in Singapore.

PubMed

Joshi, Veena D; Mooppil, Nandakumar; Lim, Jeremy Fy

2010-12-20

In Singapore, the prevalence of end-stage renal disease (ESRD) and the number of people on dialysis is increasing. The impact of ESRD on patient quality of life has been recognized as an important outcome measure. The Kidney Disease Quality Of Life-Short Form (KDQOL-SF™) has been validated and is widely used as a measure of quality of life in dialysis patients in many countries, but not in Singapore. We aimed to determine the reliability and validity of the KDQOL-SF™ for haemodialysis patients in Singapore. From December 2006 through January 2007, this cross-sectional study gathered data on patients ≥21 years old, who were undergoing haemodialysis at National Kidney Foundation in Singapore. We used exploratory factor analysis to determine construct validity of the eight KDQOL-SF™ sub-scales, Cronbach's alpha coefficient to determine internal consistency reliability, correlation of the overall health rating with kidney disease-targeted scales to confirm validity, and correlation of the eight sub-scales with age, income and education to determine convergent and divergent validity. Of 1980 haemodialysis patients, 1180 (59%) completed the KDQOL-SF™. Full information was available for 980 participants, with a mean age of 56 years. The sample was representative of the total dialysis population in Singapore, except Indian ethnicity that was over-represented. The instrument designers' proposed eight sub-scales were confirmed, which together accounted for 68.4% of the variance. All sub-scales had a Cronbach's α above the recommended minimum value of 0.7 to indicate good reliability (range: 0.72 to 0.95), except for Social function (0.66). Correlation of items within subscales was higher than correlation of items outside subscales in 90% of the cases. The overall health rating positively correlated with kidney disease-targeted scales, confirming validity. General health subscales were found to have significant associations with age, income and education, confirming convergent and divergent validity. The psychometric properties of the KDQOL-SF™ resulting from this first-time administration of the instrument support the validity and reliability of the KDQOL-SF™ as a measure of quality of life of haemodialysis patients in Singapore. It is, however, necessary to determine the test-retest reliability of the KDQOL-SF™ among the haemodialysis population of Singapore.

XSECT: A computer code for generating fuselage cross sections - user's manual

NASA Technical Reports Server (NTRS)

Ames, K. R.

1982-01-01

A computer code, XSECT, has been developed to generate fuselage cross sections from a given area distribution and wing definition. The cross sections are generated to match the wing definition while conforming to the area requirement. An iterative procedure is used to generate each cross section. Fuselage area balancing may be included in this procedure if desired. The code is intended as an aid for engineers who must first design a wing under certain aerodynamic constraints and then design a fuselage for the wing such that the contraints remain satisfied. This report contains the information necessary for accessing and executing the code, which is written in FORTRAN to execute on the Cyber 170 series computers (NOS operating system) and produces graphical output for a Tektronix 4014 CRT. The LRC graphics software is used in combination with the interface between this software and the PLOT 10 software.

Quantitative x-ray photoelectron spectroscopy: Quadrupole effects, shake-up, Shirley background, and relative sensitivity factors from a database of true x-ray photoelectron spectra

NASA Astrophysics Data System (ADS)

Seah, M. P.; Gilmore, I. S.

2006-05-01

An analysis is provided of the x-ray photoelectron spectroscopy (XPS) intensities measured in the National Physical Laboratory (NPL) XPS database for 46 solid elements. This present analysis does not change our previous conclusions concerning the excellent correlation between experimental intensities, following deconvolving the spectra with angle-averaged reflection electron energy loss data, and the theoretical intensities involving the dipole approximation using Scofield’s cross sections. Here, more recent calculations for cross sections by Trzhaskovskaya involving quadrupole terms are evaluated and it is shown that their cross sections diverge from the experimental database results by up to a factor of 5. The quadrupole angular terms lead to small corrections that are close to our measurement limit but do appear to be supported in the present analysis. Measurements of the extent of shake-up for the 46 elements broadly agree with the calculations of Yarzhemsky but not in detail. The predicted constancy in the shake-up contribution by Yarzhemsky implies that the use of the Shirley background will lead to a peak area that is a constant fraction of the true peak area including the shake-up intensities. However, the measured variability of the shake-up contribution makes the Shirley background invalid for quantification except for situations where the sensitivity factors are from reference samples similar to those being analyzed.

Design Dimensions Enabling Divergent Behaviour across Physical, Digital, and Social Library Interfaces

NASA Astrophysics Data System (ADS)

Björneborn, Lennart

What design dimensions across physical, digital, and social library interfaces may enable and trigger users to find more information resources than planned or known in advance? The paper outlines a conceptual framework with libraries as integrative interfaces across physical, digital, and social affordances and users that mix convergent (goal-directed) and divergent (exploratory) information behaviour. Ten design dimensions that enable and trigger divergent behaviour are outlined. Implications for persuasive design are discussed.

DBCC Software as Database for Collisional Cross-Sections

NASA Astrophysics Data System (ADS)

Moroz, Daniel; Moroz, Paul

2014-10-01

Interactions of species, such as atoms, radicals, molecules, electrons, and photons, in plasmas used for materials processing could be very complex, and many of them could be described in terms of collisional cross-sections. Researchers involved in plasma simulations must select reasonable cross-sections for collisional processes for implementing them into their simulation codes to be able to correctly simulate plasmas. However, collisional cross-section data are difficult to obtain, and, for some collisional processes, the cross-sections are still not known. Data on collisional cross-sections can be obtained from numerous sources including numerical calculations, experiments, journal articles, conference proceedings, scientific reports, various universities' websites, national labs and centers specifically devoted to collecting data on cross-sections. The cross-sections data received from different sources could be partial, corresponding to limited energy ranges, or could even not be in agreement. The DBCC software package was designed to help researchers in collecting, comparing, and selecting cross-sections, some of which could be constructed from others or chosen as defaults. This is important as different researchers may place trust in different cross-sections or in different sources. We will discuss the details of DBCC and demonstrate how it works and why it is beneficial to researchers working on plasma simulations.

Defining SNAP by cross-sectional and longitudinal definitions of neurodegeneration.

PubMed

Wisse, L E M; Das, S R; Davatzikos, C; Dickerson, B C; Xie, S X; Yushkevich, P A; Wolk, D A

2018-01-01

Suspected non-Alzheimer's pathophysiology (SNAP) is a biomarker driven designation that represents a heterogeneous group in terms of etiology and prognosis. SNAP has only been identified by cross-sectional neurodegeneration measures, whereas longitudinal measures might better reflect "active" neurodegeneration and might be more tightly linked to prognosis. We compare neurodegeneration defined by cross-sectional 'hippocampal volume' only (SNAP/L-) versus both cross-sectional and longitudinal 'hippocampal atrophy rate' (SNAP/L+) and investigate how these definitions impact prevalence and the clinical and biomarker profile of SNAP in Mild Cognitive Impairment (MCI). 276 MCI patients from ADNI-GO/2 were designated amyloid "positive" (A+) or "negative" (A-) based on their florbetapir scan and neurodegeneration 'positive' or 'negative' based on cross-sectional hippocampal volume and longitudinal hippocampal atrophy rate. 74.1% of all SNAP participants defined by the cross-sectional definition of neurodegeneration also met the longitudinal definition of neurodegeneration, whereas 25.9% did not. SNAP/L+ displayed larger white matter hyperintensity volume, a higher conversion rate to dementia over 5 years and a steeper decline on cognitive tasks compared to SNAP/L- and the A- CN group. SNAP/L- had more abnormal values on neuroimaging markers and worse performance on cognitive tasks than the A- CN group, but did not show a difference in dementia conversion rate or longitudinal cognition. Using a longitudinal definition of neurodegeneration in addition to a cross-sectional one identifies SNAP participants with significant cognitive decline and a worse clinical prognosis for which cerebrovascular disease may be an important driver.

Flow separation in a computational oscillating vocal fold model

NASA Astrophysics Data System (ADS)

Alipour, Fariborz; Scherer, Ronald C.

2004-09-01

A finite-volume computational model that solves the time-dependent glottal airflow within a forced-oscillation model of the glottis was employed to study glottal flow separation. Tracheal input velocity was independently controlled with a sinusoidally varying parabolic velocity profile. Control parameters included flow rate (Reynolds number), oscillation frequency and amplitude of the vocal folds, and the phase difference between the superior and inferior glottal margins. Results for static divergent glottal shapes suggest that velocity increase caused glottal separation to move downstream, but reduction in velocity increase and velocity decrease moved the separation upstream. At the fixed frequency, an increase of amplitude of the glottal walls moved the separation further downstream during glottal closing. Increase of Reynolds number caused the flow separation to move upstream in the glottis. The flow separation cross-sectional ratio ranged from approximately 1.1 to 1.9 (average of 1.47) for the divergent shapes. Results suggest that there may be a strong interaction of rate of change of airflow, inertia, and wall movement. Flow separation appeared to be ``delayed'' during the vibratory cycle, leading to movement of the separation point upstream of the glottal end only after a significant divergent angle was reached, and to persist upstream into the convergent phase of the cycle.

Effects of internal yaw-vectoring devices on the static performance of a pitch-vectoring nonaxisymmetric convergent-divergent nozzle

NASA Technical Reports Server (NTRS)

Asbury, Scott C.

1993-01-01

An investigation was conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to evaluate the internal performance of a nonaxisymmetric convergent divergent nozzle designed to have simultaneous pitch and yaw thrust vectoring capability. This concept utilized divergent flap deflection for thrust vectoring in the pitch plane and flow-turning deflectors installed within the divergent flaps for yaw thrust vectoring. Modifications consisting of reducing the sidewall length and deflecting the sidewall outboard were investigated as means to increase yaw-vectoring performance. This investigation studied the effects of multiaxis (pitch and yaw) thrust vectoring on nozzle internal performance characteristics. All tests were conducted with no external flow, and nozzle pressure ratio was varied from 2.0 to approximately 13.0. The results indicate that this nozzle concept can successfully generate multiaxis thrust vectoring. Deflection of the divergent flaps produced resultant pitch vector angles that, although dependent on nozzle pressure ratio, were nearly equal to the geometric pitch vector angle. Losses in resultant thrust due to pitch vectoring were small or negligible. The yaw deflectors produced resultant yaw vector angles up to 21 degrees that were controllable by varying yaw deflector rotation. However, yaw deflector rotation resulted in significant losses in thrust ratios and, in some cases, nozzle discharge coefficient. Either of the sidewall modifications generally reduced these losses and increased maximum resultant yaw vector angle. During multiaxis (simultaneous pitch and yaw) thrust vectoring, little or no cross coupling between the thrust vectoring processes was observed.

The Worry Behaviors Inventory: Assessing the behavioral avoidance associated with generalized anxiety disorder.

PubMed

Mahoney, Alison E J; Hobbs, Megan J; Newby, Jill M; Williams, Alishia D; Sunderland, Matthew; Andrews, Gavin

2016-10-01

Understanding behavioral avoidance associated with generalized anxiety disorder (GAD) has implications for the classification, theoretical conceptualization, and clinical management of the disorder. This study describes the development and preliminary psychometric evaluation of a self-report measure of avoidant behaviors associated with GAD: the Worry Behaviors Inventory (WBI). The WBI was administered to treatment-seeking patients (N=1201). Convergent validity was assessed by correlating the WBI with measures of GAD symptom severity. Divergent validity was assessed by correlating the WBI with measures of general disability and measures of depression, social anxiety and panic disorder symptom severity. Exploratory and confirmatory factor analyses supported a two-factor structure (Safety Behaviors and Avoidance). Internal reliability was acceptable for the 10-item WBI scale (α=.86), Safety Behaviors (α=.85) and Avoidance subscales (α=.75). Evidence of convergent, divergent, and discriminant validity is reported. WBI subscales demonstrated differential associations with measures of symptom severity. The Safety Behaviors subscale was more strongly associated with GAD symptoms than symptoms of other disorders, whereas the Avoidance subscale was as strongly correlated with GAD severity as it was with depression, social anxiety and panic disorder severity. Structured diagnostic interviews were not conducted therefor validity analyses are limited to probable diagnoses based on self-report. The cross-sectional design precluded examination of the WBI's temporal stability and treatment sensitivity. Preliminary evidence supports the use of the WBI in research and clinical settings and may assist clinicians to identify behaviors that are theorized to maintain GAD and that can be targeted during psychological treatment. Copyright © 2016 Elsevier B.V. All rights reserved.

Computer Graphic Design Using Auto-CAD and Plug Nozzle Research

NASA Technical Reports Server (NTRS)

Rogers, Rayna C.

2004-01-01

The purpose of creating computer generated images varies widely. They can be use for computational fluid dynamics (CFD), or as a blueprint for designing parts. The schematic that I will be working on the summer will be used to create nozzles that are a part of a larger system. At this phase in the project, the nozzles needed for the systems have been fabricated. One part of my mission is to create both three dimensional and two dimensional models on Auto-CAD 2002 of the nozzles. The research on plug nozzles will allow me to have a better understanding of how they assist in the thrust need for a missile to take off. NASA and the United States military are working together to develop a new design concept. On most missiles a convergent-divergent nozzle is used to create thrust. However, the two are looking into different concepts for the nozzle. The standard convergent-divergent nozzle forces a mixture of combustible fluids and air through a smaller area in comparison to where the combination was mixed. Once it passes through the smaller area known as A8 it comes out the end of the nozzle which is larger the first or area A9. This creates enough thrust for the mechanism whether it is an F-18 fighter jet or a missile. The A9 section of the convergent-divergent nozzle has a mechanism that controls how large A9 can be. This is needed because the pressure of the air coming out nozzle must be equal to that of the ambient pressure other wise there will be a loss of performance in the machine. The plug nozzle however does not need to have an A9 that can vary. When the air flow comes out it can automatically sense what the ambient pressure is and will adjust accordingly. The objective of this design is to create a plug nozzle that is not as complicated mechanically as it counterpart the convergent-divergent nozzle.

Flexible metamaterial absorbers for stealth applications at terahertz frequencies.

PubMed

Iwaszczuk, Krzysztof; Strikwerda, Andrew C; Fan, Kebin; Zhang, Xin; Averitt, Richard D; Jepsen, Peter Uhd

2012-01-02

We have wrapped metallic cylinders with strongly absorbing metamaterials. These resonant structures, which are patterned on flexible substrates, smoothly coat the cylinder and give it an electromagnetic response designed to minimize its radar cross section. We compare the normal-incidence, small-beam reflection coefficient with the measurement of the far-field bistatic radar cross section of the sample, using a quasi-planar THz wave with a beam diameter significantly larger than the sample dimensions. In this geometry we demonstrate a near-400-fold reduction of the radar cross section at the design frequency of 0.87 THz. In addition we discuss the effect of finite sample dimensions and the spatial dependence of the reflection spectrum of the metamaterial.

WinXSPRO, a channel cross section analyzer, User's Manual, Version 3.0

Treesearch

Thomas Hardy; Palavi Panja; Dean Mathias

2005-01-01

WinXSPRO is an interactive Windows software package designed to analyze stream channel cross section data for geometric, hydraulic, and sediment transport parameters. WinXSPRO was specifically developed for use in high-gradient streams (gradient > 0.01) and supports four alternative resistance equations for computing boundary roughness and resistance to flow. Cross...

Flowing Air-Water Cooled Slab Nd: Glass Laser

NASA Astrophysics Data System (ADS)

Lu, Baida; Cai, Bangwei; Liao, Y.; Xu, Shifa; Xin, Z.

1989-03-01

A zig-zag optical path slab geometry Nd: glass laser cooled through flowing air-water is developed by us. Theoretical studies on temperature distribution of slab and rod configurations in the unsteady state clarify the advantages of the slab geometry laser. The slab design and processing are also reported. In our experiments main laser output characteristics, e. g. laser efficiency, polarization, far-field divergence angle as well as resonator misalignment are investigated. The slab phosphate glass laser in combination with a crossed Porro-prism resonator demonstrates a good laser performance.

The Neighbourhood Effects on Health and Well-being (NEHW) study.

PubMed

O'Campo, Patricia; Wheaton, Blair; Nisenbaum, Rosane; Glazier, Richard H; Dunn, James R; Chambers, Catharine

2015-01-01

Many cross-sectional studies of neighbourhood effects on health do not employ strong study design elements. The Neighbourhood Effects on Health and Well-being (NEHW) study, a random sample of 2412 English-speaking Toronto residents (age 25-64), utilises strong design features for sampling neighbourhoods and individuals, characterising neighbourhoods using a variety of data sources, measuring a wide range of health outcomes, and for analysing cross-level interactions. We describe here methodological issues that shaped the design and analysis features of the NEHW study to ensure that, while a cross-sectional sample, it will advance the quality of evidence emerging from observational studies. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Axial Crushing of Thin-Walled Columns with Octagonal Section: Modeling and Design

NASA Astrophysics Data System (ADS)

Liu, Yucheng; Day, Michael L.

This chapter focus on numerical crashworthiness analysis of straight thinwalled columns with octagonal cross sections. Two important issues in this analysis are demonstrated here: computer modeling and crashworthiness design. In the first part, this chapter introduces a method of developing simplified finite element (FE) models for the straight thin-walled octagonal columns, which can be used for the numerical crashworthiness analysis. Next, this chapter performs a crashworthiness design for such thin-walled columns in order to maximize their energy absorption capability. Specific energy absorption (SEA) is set as the design objective, side length of the octagonal cross section and wall thickness are selected as design variables, and maximum crushing force (Pm) occurs during crashes is set as design constraint. Response surface method (RSM) is employed to formulate functions for both SEA and Pm.

Mean-flow measurements of the flow field diffusing bend

NASA Technical Reports Server (NTRS)

Mcmillan, O. J.

1982-01-01

Time-average measurements of the low-speed turbulent flow in a diffusing bend are presented. The experimental geometry consists of parallel top and bottom walls and curved diverging side walls. The turning of the center line of this channel is 40 deg, the area ratio is 1.5 and the ratios of height and center-line length to throat width are 1.5 and 3, respectively. The diffusing bend is preceded and followed by straight constant area sections. The inlet boundary layers on the parallel walls are artificially thickened and occupy about 30% of the channel height; those on the side walls develop naturally and are about half as thick. The free-stream speed at the inlet was approximately 30 m/sec for all the measurements. Inlet boundary layer mean velocity and turbulence intensity profiles are presented, as are data for wall static pressures, and at six cross sections, surveys of the velocity-vector and static-pressure fields. The dominant feature of the flow field is a pair of counter-rotating streamwise vortices formed by the cross-stream pressure gradient in the bend on which an overall deceleration is superimposed.

Diallel crossing among doubled haploids of cucumber reveals significant reciprocal-cross differences

USDA-ARS?s Scientific Manuscript database

Cucumber is an excellent plant for studying organellar effects on phenotypes because chloroplasts show maternal and mitochondria paternal transmission. We produced doubled haploids (DH) from divergent cucumber populations, generated reciprocal crosses in a diallel mating scheme, measured fresh and d...

Dental Students’ Educational Achievement in Relation to Their Learning Styles: A Cross-sectional Study in Iran

PubMed Central

Hosseini, Seyed Masoud; Amery, Hamideh; Emadzadeh, Ali; Babazadeh, Saber

2015-01-01

Background and Objectives: In recent decades, many studies have been carried out on the importance of Kolb experiential learning theory (ELT) in teaching-learning processes and its effect on learning outcomes. However, some experts have criticized the Kolb theory and argue that there are some ambiguities on the validity of the theory as an important predictor of achievement. This study has been carried out on dental students’ educational achievement in relation to their dominant learning styles based on Kolb theory in Mashhad University of Medical Sciences (Iran). Methods: In a cross sectional study, Kolb Learning Style Inventory (LSI Ver. 3.1) as well as a questionnaire containing students’ demographic data, academic achievement marks including grade point average (GPA), theoretical and practical courses marks, and the comprehensive basic sciences exam (CBSE) scores were administered on a purposive sample of 162 dental students who had passed their comprehensive basic sciences exam. Educational achievement data were analyzed in relation to students’ dominant learning styles, using descriptive and analytical statistics including χ2, Kruskal-Wallis and two-way ANOVA tests. Results: The dominant learning styles of students were Assimilating (53.1%), Converging (24.1%), Diverging (14.2%) and Accommodating (8.6%). Although, the students with Assimilating and Converging learning styles had a better performance on their educational achievement, there was no significant relationship between educational achievement and dominant learning style (P≥0.05). Conclusion: Findings support that the dominant learning style is not exclusively an essential factor to predict educational achievement. Rather, it shows learning preferences of students that may be considered in designing learning opportunities by the teachers. PMID:26156915

Detection of a transient mitochondrial DNA heteroplasmy in the progeny of crossed genetically divergent isolates of arbuscular mycorrhizal fungi.

PubMed

de la Providencia, Ivan Enrique; Nadimi, Maryam; Beaudet, Denis; Morales, Gabriela Rodriguez; Hijri, Mohamed

2013-10-01

Nonself fusion and nuclear genetic exchange have been documented in arbuscular mycorrhizal fungi (AMF), particularly in Rhizophagus irregularis. However, mitochondrial transmission accompanying nonself fusion of genetically divergent isolates remains unknown. Here, we tested the hypothesis that mitochondrial DNA (mtDNA) heteroplasmy occurs in the progeny of spores, obtained by crossing genetically divergent mtDNAs in R. irregularis isolates. Three isolates of geographically distant locations were used to investigate nonself fusions and mtDNA transmission to the progeny. We sequenced two additional mtDNAs of two R. irregularis isolates and developed isolate-specific size-variable markers in intergenic regions of these isolates and those of DAOM-197198. We achieved three crossing combinations in pre-symbiotic and symbiotic phases. Progeny spores per crossing combination were genotyped using isolate-specific markers. We found evidence that nonself recognition occurs between isolates originating from different continents both in pre-symbiotic and symbiotic phases. Genotyping patterns of individual spores from the progeny clearly showed the presence of markers of the two parental mtDNA haplotypes. Our results demonstrate that mtDNA heteroplasmy occurs in the progeny of the crossed isolates. However, this heteroplasmy appears to be a transient stage because all the live progeny spores that were able to germinate showed only one mtDNA haplotype. © 2013 The Authors. New Phytologist © 2013 New Phytologist Trust.

Biomimetic optimization research on wind noise reduction of an asymmetric cross-section bar.

PubMed

Zhang, Yingchao; Meng, Weijiang; Fan, Bing; Tang, Wenhui

2016-01-01

In this paper, we used the principle of biomimetics to design two-dimensional and three-dimensional bar sections, and used computational fluid dynamics software to numerically simulate and analyse the aerodynamic noise, to reduce drag and noise. We used the principle of biomimetics to design the cross-section of a bar. An owl wing shape was used for the initial design of the section geometry; then the feathered form of an owl wing, the v-shaped micro-grooves of a shark's skin, the tubercles of a humpback whale's flipper, and the stripy surface of a scallop's shell were used to inspire surface features, added to the initial section and three-dimensional shape. Through computational aeroacoustic simulations, we obtained the aerodynamic characteristics and the noise levels of the models. These biomimetic models dramatically decreased noise levels.

Analysis of detection performance of multi band laser beam analyzer

NASA Astrophysics Data System (ADS)

Du, Baolin; Chen, Xiaomei; Hu, Leili

2017-10-01

Compared with microwave radar, Laser radar has high resolution, strong anti-interference ability and good hiding ability, so it becomes the focus of laser technology engineering application. A large scale Laser radar cross section (LRCS) measurement system is designed and experimentally tested. First, the boundary conditions are measured and the long range laser echo power is estimated according to the actual requirements. The estimation results show that the echo power is greater than the detector's response power. Secondly, a large scale LRCS measurement system is designed according to the demonstration and estimation. The system mainly consists of laser shaping, beam emitting device, laser echo receiving device and integrated control device. Finally, according to the designed lidar cross section measurement system, the scattering cross section of target is simulated and tested. The simulation results are basically the same as the test results, and the correctness of the system is proved.

NEUTRONIC REACTOR

DOEpatents

Wigner, E.P.

1958-04-22

A nuclear reactor for isotope production is described. This reactor is designed to provide a maximum thermal neutron flux in a region adjacent to the periphery of the reactor rather than in the center of the reactor. The core of the reactor is generally centrally located with respect tn a surrounding first reflector, constructed of beryllium. The beryllium reflector is surrounded by a second reflector, constructed of graphite, which, in tune, is surrounded by a conventional thermal shield. Water is circulated through the core and the reflector and functions both as a moderator and a coolant. In order to produce a greatsr maximum thermal neutron flux adjacent to the periphery of the reactor rather than in the core, the reactor is designed so tbat the ratio of neutron scattering cross section to neutron absorption cross section averaged over all of the materials in the reflector is approximately twice the ratio of neutron scattering cross section to neutron absorption cross section averaged over all of the material of the core of the reactor.

Thermoelastic damping in microrings with circular cross-section

NASA Astrophysics Data System (ADS)

Li, Pu; Fang, Yuming; Zhang, Jianrun

2016-01-01

Predicting thermoelastic damping (TED) is crucial in the design of high Q micro-resonators. Microrings are often critical components in many micro-resonators. Some analytical models for TED in microrings have already been developed in the past. However, the previous works are limited to the microrings with rectangular cross-section. The temperature field in the rectangular cross-section is one-dimensional. This paper deals with TED in the microrings with circular cross-section. The temperature field in the circular cross-section is two-dimensional. This paper first presents a 2-D analytical model for TED in the microrings with circular cross-section. Only the two-dimensional heat conduction in the circular cross-section is considered. The heat conduction along the circumferential direction of the microring is neglected in the 2-D model. Then the 2-D model has been extended to cover the circumferential heat conduction, and a 3-D analytical model for TED has been developed. The analytical results from the present 2-D and 3-D models show good agreement with the numerical results of FEM model. The limitations of the present 2-D analytical model are assessed.

Detecting deep divergence in seventeen populations of tea geometrid (Ectropis obliqua Prout) in China by COI mtDNA and cross-breeding.

PubMed

Zhang, Gui-Hua; Yuan, Zhi-Jun; Zhang, Chuan-Xi; Yin, Kun-Shan; Tang, Mei-Jun; Guo, Hua-Wei; Fu, Jian-Yu; Xiao, Qiang

2014-01-01

The tea geometrid (Ectropis obliqua Prout, Lepidoptera: Geometridae) is a dominant chewing insect endemic in most tea-growing areas in China. Recently some E. obliqua populations have been found to be resistant to the nucleopolyhedrovirus (EoNPV), a host-specific virus that has so far been found only in E. obliqua. Although the resistant populations are morphologically indistinguishable from susceptible populations, we conducted a nationwide collection and examined the genetic divergence in the COI region of the mtDNA in E. obliqua. Phylogenetic analyses of mtDNA in 17 populations revealed two divergent clades with genetic distance greater than 3.7% between clades and less than 0.7% within clades. Therefore, we suggest that E. obliqua falls into two distinct groups. Further inheritance analyses using reciprocal single-pair mating showed an abnormal F₁ generation with an unbalanced sex ratio and the inability to produce fertile eggs (or any eggs) through F1 self-crossing. These data revealed a potential cryptic species complex with deep divergence and reproductive isolation within E. obliqua. Uneven distribution of the groups suggests a possible geographic effect on the divergence. Future investigations will be conducted to examine whether EoNPV selection or other factors prompted the evolution of resistance.

Design and optimization of resistance wire electric heater for hypersonic wind tunnel

NASA Astrophysics Data System (ADS)

Rehman, Khurram; Malik, Afzaal M.; Khan, I. J.; Hassan, Jehangir

2012-06-01

The range of flow velocities of high speed wind tunnels varies from Mach 1.0 to hypersonic order. In order to achieve such high speed flows, a high expansion nozzle is employed in the converging-diverging section of wind tunnel nozzle. The air for flow is compressed and stored in pressure vessels at temperatures close to ambient conditions. The stored air is dried and has minimum amount of moisture level. However, when this air is expanded rapidly, its temperature drops significantly and liquefaction conditions can be encountered. Air at near room temperature will liquefy due to expansion cooling at a flow velocity of more than Mach 4.0 in a wind tunnel test section. Such liquefaction may not only be hazardous to the model under test and wind tunnel structure; it may also affect the test results. In order to avoid liquefaction of air, a pre-heater is employed in between the pressure vessel and the converging-diverging section of a wind tunnel. A number of techniques are being used for heating the flow in high speed wind tunnels. Some of these include the electric arc heating, pebble bed electric heating, pebble bed natural gas fired heater, hydrogen burner heater, and the laser heater mechanisms. The most common are the pebble bed storage type heaters, which are inefficient, contaminating and time consuming. A well designed electrically heating system can be efficient, clean and simple in operation, for accelerating the wind tunnel flow up to Mach 10. This paper presents CFD analysis of electric preheater for different configurations to optimize its design. This analysis has been done using ANSYS 12.1 FLUENT package while geometry and meshing was done in GAMBIT.

Assessment of optimum threshold and particle shape parameter for the image analysis of aggregate size distribution of concrete sections

NASA Astrophysics Data System (ADS)

Ozen, Murat; Guler, Murat

2014-02-01

Aggregate gradation is one of the key design parameters affecting the workability and strength properties of concrete mixtures. Estimating aggregate gradation from hardened concrete samples can offer valuable insights into the quality of mixtures in terms of the degree of segregation and the amount of deviation from the specified gradation limits. In this study, a methodology is introduced to determine the particle size distribution of aggregates from 2D cross sectional images of concrete samples. The samples used in the study were fabricated from six mix designs by varying the aggregate gradation, aggregate source and maximum aggregate size with five replicates of each design combination. Each sample was cut into three pieces using a diamond saw and then scanned to obtain the cross sectional images using a desktop flatbed scanner. An algorithm is proposed to determine the optimum threshold for the image analysis of the cross sections. A procedure was also suggested to determine a suitable particle shape parameter to be used in the analysis of aggregate size distribution within each cross section. Results of analyses indicated that the optimum threshold hence the pixel distribution functions may be different even for the cross sections of an identical concrete sample. Besides, the maximum ferret diameter is the most suitable shape parameter to estimate the size distribution of aggregates when computed based on the diagonal sieve opening. The outcome of this study can be of practical value for the practitioners to evaluate concrete in terms of the degree of segregation and the bounds of mixture's gradation achieved during manufacturing.

Integrated system for production of neutronics and photonics calculational constants. Program SIGMA1 (Version 77-1): Doppler broaden evaluated cross sections in the Evaluated Nuclear Data File/Version B (ENDF/B) format

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cullen, D.E.

1977-01-12

A code, SIGMA1, has been designed to Doppler broaden evaluated cross sections in the ENDF/B format. The code can only be applied to tabulated data that vary linearly in energy and cross section between tabulated points. This report describes the methods used in the code and serves as a user's guide to the code.

Noise Characteristics of Overexpanded Jets from Convergent-Divergent Nozzles

NASA Technical Reports Server (NTRS)

Zaman, K. B. M. Q.

2008-01-01

A broadband noise component occurring in the overexpanded flow regime with convergent-divergent nozzles is identified. Relative to a convergent nozzle, at same pressure ratios, this excess noise can lead to a large increase in the overall sound pressure levels. Several features distinguish it from the more familiar broadband shock associated noise. Unlike the latter, it is observed even at shallow polar locations and there is no noticeable shift of the spectral content in frequency with observation angle. The amplitudes are found to be more pronounced with nozzles having larger half-angle of the divergent section. The noise apparently occurs when a shock resides within the divergent section of the nozzle and results from random unsteady motion of the shock.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Monaghan, P; Shneor, R; Subedi, R

The five-fold differential cross section for the 12C(e,e'p)11B reaction was determined over a missing momentum range of 200-400 MeV/c, in a kinematics regime with Bjorken x > 1 and Q2 = 2.0 (GeV/c)2. A comparison of the results and theoretical models and previous lower missing momentum data is shown. The theoretical calculations agree well with the data up to a missing momentum value of 325 MeV/c and then diverge for larger missing momenta. The extracted distorted momentum distribution is shown to be consistent with previous data and extends the range of available data up to 400 MeV/c.

Supersonic jet noise and the high speed civil transport

NASA Astrophysics Data System (ADS)

Seiner, John M.; Krejsa, Eugene A.

1989-07-01

An evaluation is made of the comparative advantages of prospective SST engine noise-suppression systems, with a view to their effectiveness in meeting the federally-mandated community noise standards of FAR 36 Stage III. A noise-suppression system must be capable of removing at least 4 EPNdB of noise percent thrust loss at takeoff. While none of the suppressors presently discussed is capable of meeting this goal, the inverted velocity profile/annular convergent-divergent plug/acoustically-treated ejector suppressor combination of configurational elements appears to represent the most efficient noise-control apparatus. Noncircular cross-section nozzle geometries also furnish a general noise reduction advantage over circular ones.

Teaching for Cross Cultural Understanding.

ERIC Educational Resources Information Center

Arlington County Public Schools, VA.

The document contains materials prepared for a workshop designed to foster cross-cultural understanding in junior high school teachers. It is presented in six sections. Section I defines several key concepts such as culture, racism, ethnic diversity, stereotype, pluralism, ethnic encapsulization, and types of teaching styles and dialects.…

Engaging Students in Designing Movement: The Divergent Discovery Style of Teaching

ERIC Educational Resources Information Center

Chatoupis, Constantine

2018-01-01

In the divergent discovery style of teaching the teacher designs problems that engage students in finding multiple solutions. The purpose of this article is to show how physical educators can use the divergent discovery style in the gymnasium. A brief description of this style and its connection to the SHAPE America National Standards for K-12…

A Simple and Efficient Device for Demonstrating Cross-Sectional Anatomy of the Head

ERIC Educational Resources Information Center

Zamarioli, Ariane; Demaman, Aline Santos; Bim, Waldeci Roberto; Homem, Jefferson Mallman; Thomazini, Jose Antonio

2010-01-01

Described in this article is a novel device that facilitates study of the cross-sectional anatomy of the human head. In designing our device, we aimed to protect sections of the head from the destructive action of handling during anatomy laboratory while also ensuring excellent visualization of the anatomic structures. We used an electric saw to…

Development of a general method for obtaining the geometry of microfluidic networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Razavi, Mohammad Sayed, E-mail: m.sayedrazavi@gmail.com; Salimpour, M. R.; Shirani, Ebrahim

2014-01-15

In the present study, a general method for geometry of fluidic networks is developed with emphasis on pressure-driven flows in the microfluidic applications. The design method is based on general features of network's geometry such as cross-sectional area and length of channels. Also, the method is applicable to various cross-sectional shapes such as circular, rectangular, triangular, and trapezoidal cross sections. Using constructal theory, the flow resistance, energy loss and performance of the network are optimized. Also, by this method, practical design strategies for the fabrication of microfluidic networks can be improved. The design method enables rapid prediction of fluid flowmore » in the complex network of channels and is very useful for improving proper miniaturization and integration of microfluidic networks. Minimization of flow resistance of the network of channels leads to universal constants for consecutive cross-sectional areas and lengths. For a Y-shaped network, the optimal ratios of consecutive cross-section areas (A{sub i+1}/A{sub i}) and lengths (L{sub i+1}/L{sub i}) are obtained as A{sub i+1}/A{sub i} = 2{sup −2/3} and L{sub i+1}/L{sub i} = 2{sup −1/3}, respectively. It is shown that energy loss in the network is proportional to the volume of network. It is also seen when the number of channels is increased both the hydraulic resistance and the volume occupied by the network are increased in a similar manner. Furthermore, the method offers that fabrication of multi-depth and multi-width microchannels should be considered as an integral part of designing procedures. Finally, numerical simulations for the fluid flow in the network have been performed and results show very good agreement with analytic results.« less

Statistical Features of the Thermal Neutron Capture Cross Sections

DOE PAGES

Hussein, M. S.; Carlson, B. V.; Kerman, A. K.

2016-02-01

In this paper, we discuss the existence of huge thermal neutron capture cross sections in several nuclei. The values of the cross sections are several orders of magnitude bigger than expected at these very low energies. We lend support to the idea that this phenomenon is random in nature and is similar to what we have learned from the study of parity violation in the actinide region. The idea of statistical doorways is advanced as a unified concept in the delineation of large numbers in the nuclear world. The average number of maxima per unit mass, < n A >more » in the capture cross section is calculated and related to the underlying cross section correlation function and found to be < n A > = 3/(π√2γ A), where γ A is a characteristic mass correlation width which designates the degree of remnant coherence in the system. Finally, we trace this coherence to nucleosynthesis which produced the nuclei whose neutron capture cross sections are considered here.« less

Statistical Features of the Thermal Neutron Capture Cross Sections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hussein, M. S.; Carlson, B. V.; Kerman, A. K.

In this paper, we discuss the existence of huge thermal neutron capture cross sections in several nuclei. The values of the cross sections are several orders of magnitude bigger than expected at these very low energies. We lend support to the idea that this phenomenon is random in nature and is similar to what we have learned from the study of parity violation in the actinide region. The idea of statistical doorways is advanced as a unified concept in the delineation of large numbers in the nuclear world. The average number of maxima per unit mass, < n A >more » in the capture cross section is calculated and related to the underlying cross section correlation function and found to be < n A > = 3/(π√2γ A), where γ A is a characteristic mass correlation width which designates the degree of remnant coherence in the system. Finally, we trace this coherence to nucleosynthesis which produced the nuclei whose neutron capture cross sections are considered here.« less

Temperature- and pressure-dependent absorption cross sections of gaseous hydrocarbons at 3.39 µm

NASA Astrophysics Data System (ADS)

Klingbeil, A. E.; Jeffries, J. B.; Hanson, R. K.

2006-07-01

The pressure- and temperature-dependent absorption cross sections of several neat hydrocarbons and multi-component fuels are measured using a 3.39 µm helium-neon laser. Absorption cross section measurements are reported for methane, ethylene, propane, n-heptane, iso-octane, n-decane, n-dodecane, JP-10, gasoline and jet-A with an estimated uncertainty of less than 3.5%. The experimental conditions range from 298 to 673 K and from 500 to 2000 Torr with nitrogen as the bath gas. An apparatus is designed to facilitate these measurements, and specific care is taken to ensure the compositional accuracy of the hydrocarbon/N2 mixtures. The absorption cross sections of the smallest hydrocarbons, methane and ethylene, vary with temperature and pressure. The cross sections of larger hydrocarbons show negligible dependence on pressure and only a weak dependence on temperature. The reported data increase the range of conditions and the number of hydrocarbons for which cross section measurements are available at the HeNe laser wavelength.

Special Course on Fundamentals of Fighter Aircraft Design

DTIC Science & Technology

1987-10-01

mounted centrally on a cylindrical fuselage of circular cross-section. Here the fuselage interference is shown by a calculation with an exact...M. and Schiff, L.B., "Aerodynamic Mathematical Modeling - Basic Concepts", AGARD-LS-114, 1981, Lecture 1. 30. Malcolm, G.N., "Rotary and Magnus ...thin cylindrical Intake 1.5.3. Real Intake equivalence 1.5.4. Lip thickness and auxiliary intake design 1.6. AIR INTAKE RADAR CROSS SECTION (R.C.S

Research on the Cross Section Precision of High-strength Steel Tube with Rectangular Section in Rotary Draw Bending

NASA Astrophysics Data System (ADS)

Yang, Hongliang; Zhao, Hao; Xing, Zhongwen

2017-11-01

For the demand of energy conservation and security improvement, high-strength steel (HSS) is increasingly being used to produce safety related automotive components. However, cross-section distortion occurs easily in bending of HSS tube with rectangular section (RS), affecting the forming precision. HSS BR1500HS tube by rotary draw bending is taken as the study object and a description method of cross-section distortion is proposed in this paper. The influence on cross-section precision of geometric parameters including cross-section position, thickness of tube, bend radius etc. are studied by experiment. Besides, simulation of the rotary draw bending of HSS tube with rectangular section by ABAQUS are carried out and compared to the experiment. The results by simulation agree well with the experiment and show that the cross-section is approximately trapezoidal after distortion; the maximum of distortion exists at 45 ∼ 60° of the bending direction; and the absolute and relative distortion values increase with the decreasing of tube thickness or bending radius. Therefore, the results can provide a reference for the design of geometric parameters of HSS tube with rectangular section in rotary draw bending.

30 CFR 56.9104 - Railroad crossings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Railroad crossings. 56.9104 Section 56.9104 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Dumping Traffic Safety § 56.9104 Railroad crossings. Designated railroad crossings shall be posted with...

30 CFR 57.9104 - Railroad crossings.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Railroad crossings. 57.9104 Section 57.9104 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE... Dumping Traffic Safety § 57.9104 Railroad crossings. Designated railroad crossings shall be posted with...

Two-photon absorption in diazobenzene compounds

NASA Astrophysics Data System (ADS)

Andrade, A. A.; Yamaki, S. B.; Misoguti, L.; Zilio, S. C.; Atvars, Teresa D. Z.; Oliveira, O. N.; Mendonça, C. R.

2004-12-01

An investigation is made into molecular design strategies to enhance the two-photon absorption (2PA) of organic materials by measuring the 2PA cross-section of diazoaromatic compounds with the femtosecond pulses Z-scan technique at 775 nm. These diazo dyes exhibit a moderate 2PA cross-section, of the order of 300 GM, comparable to those of regular azoaromatic compounds. The increase in the π-electron bridge in the diazoaromatic compounds does not bring, therefore, substantial increase to the measured 2PA intensities, while the main factor to enhance the 2PA cross-section is the presence of charge donor and acceptor groups. It is concluded that current molecular design strategies are unlikely to produce azoaromatic compounds that are useful for applications requiring very high 2PA coefficients.

Amphetamine-type stimulants and HIV infection among men who have sex with men: implications on HIV research and prevention from a systematic review and meta-analysis

PubMed Central

Thu Vu, Nga Thi; Maher, Lisa; Zablotska, Iryna

2015-01-01

Introduction HIV infections and the use of amphetamine-type stimulants (ATS) among men who have sex with men (MSM) have been increasing internationally, but the role of ATS use as a co-factor for HIV infection remains unclear. We aimed to summarize the association between ATS use and HIV infection among MSM. Methods We conducted a systematic search of MEDLINE, EMBASE, GLOBAL HEALTH and PsycINFO for relevant English, peer-reviewed articles of quantitative studies published between 1980 and 25 April 2013. Pooled estimates of the association – prevalence rate ratios (PRR, cross-sectional studies), odds ratio (OR, case-control studies) and hazard ratio (HR, longitudinal studies), with 95% Confidence Intervals (CI) – were calculated using random-effects models stratified by study design and ATS group (meth/amphetamines vs. ecstasy). We assessed the existence of publication bias in funnel plots and checked for sources of heterogeneity using meta-regression and subgroup analysis. Results We identified 6710 article titles, screened 1716 abstracts and reviewed 267 full text articles. A total of 35 publications were eligible for data abstraction and meta-analysis, resulting in 56 records of ATS use. Most studies (31/35) were conducted in high-income countries. Published studies used different research designs, samples and measures of ATS use. The pooled association between meth/amphetamine use and HIV infection was statistically significant in all three designs (PRR=1.86; 95% CI: 1.57–2.17; OR=2.73; 95% CI: 2.16–3.46 and HR=3.43; 95% CI: 2.98–3.95, respectively, for cross-sectional, case-control and longitudinal studies). Ecstasy use was not associated with HIV infection in cross-sectional studies (PRR=1.15; 95% CI: 0.88–1.49; OR=3.04; 95% CI: 1.29–7.18 and HR=2.48; 95% CI: 1.42–4.35, respectively, for cross-sectional, case-control and longitudinal studies). Results in cross-sectional studies were highly heterogeneous due to issues with ATS measurement and different sampling frames. Conclusions While meth/amphetamine use was significantly associated with HIV infection among MSM in high-income countries in all study designs, evidence of the role of ecstasy in HIV infection was lacking in cross-sectional studies. Cross-sectional study design, measurement approaches and source populations may also be important modifiers of the strength and the direction of associations. Event-specific measure of individual drug is required to establish temporal relationship between ATS use and HIV infection. HIV prevention programmes targeting MSM should consider including interventions designed to address meth/amphetamine use. PMID:25609214

Psychometric properties of the Chinese version of the Life Attitude Schedule (LAS-C) in a sample of Taiwanese adolescents.

PubMed

Chang, Hsiu-Ju; Wu, Chiung-Jane; Chen, Tzen Wen; Cheng, Andrew Tai Ann; Lin, Kuan-Chia; Rong, Jiin-Ru; Lee, Hsin-Chien

2011-05-01

Although prior research has proposed that several risk factors are conceptually and positively related to suicidal behavior, researchers have also suggested that suicide may be multifaceted. The Life Attitude Schedule (LAS) measures a broad range of suicide-related behaviors, including life-enhancing and life-threatening behaviors. This study aimed to translate the LAS into Chinese and evaluate the psychometric properties of the new version (LAS-C). A cross-sectional and descriptive design was used. Data were collected from high schools in the city of Taipei in northern Taiwan. A convenience sample of 1492 high school students was recruited from five high schools in Taipei. We used the Multi-Health Systems (MHS) translation policy to guide the translation process. Reliability was evaluated by internal consistency (represented by Cronbach's α coefficients) and test-retest (represented by intraclass correlation). Validity was demonstrated by content, convergent, divergent, concurrent, and contrast group comparison. Confirmatory factor analysis was further used to examine the theoretical model and to support construct validity. The Cronbach's α coefficient for the whole scale of the LAS-C and its subscales ranged from 0.70 to 0.91. The Intraclass Correlation Coefficient (ICC) ranged from 0.76 to 0.89 on the whole scale and its subscales, and were all statistically significant, at least at the p<0.05 level, indicating good stability over a three-week period. Validity was supported by a Content Validity Index (CVI) of 0.99, convergent, divergent, current, and contrast group comparison validity. Confirmatory factor analysis supported the theoretical model, further providing solid evidence of construct validity. The LAS-C has proper psychometric properties. Future studies must be conducted to shorten the items to form a briefer version. Copyright © 2010 Elsevier Ltd. All rights reserved.

The LArIAT experiment: first measurement of the inclusive total pion cross-section in Argon

NASA Astrophysics Data System (ADS)

de María Blaszczyk, Flor

2018-05-01

In light of future large neutrino experiments such as DUNE, an excellent understanding of LArTPCs is required. The Liquid Argon In A Test-beam (LArIAT) experiment, located in the Fermilab Test Beam Facility, is designed to characterize the performance of LArTPCs and improve the reconstruction algorithms but also to measure the cross-sections of charged particles in Argon. The goals and experimental layout will be presented, as well as the world’s first inclusive total pion interaction cross-section on Argon measured by LArIAT.

Sub-barrier fusion cross section measurements with STELLA

NASA Astrophysics Data System (ADS)

Heine, M.; Courtin, S.; Fruet, G.; Jenkins, D. G.; Montanari, D.; Adsley, P.; Beck, C.; Della Negra, S.; Dené, P.; Haas, F.; Hammache, F.; Heitz, G.; Kirsebom, O. S.; Krauth, M.; Lesrel, J.; Meyer, A.; Morris, L.; Regan, P. H.; Richer, M.; Rudigier, M.; de Séréville, N.; Stodel, C.

2018-01-01

The experimental setup STELLA (STELlar LAboratory) is designed for the measurement of deep sub-barrier light heavy ion fusion cross sections. For background suppression the γ-particle coincidence technique is used. In this project, LaBr3 detectors from the UK FATIMA (FAst TIMing Array) collaboration are combined with annular silicon strip detectors customized at IPHC-CNRS, Strasbourg, and the setup is located at Andromède, IPN, Orsay. The commissioning of the experimental approach as well as a sub-barrier 12C +12C → 24Mg∗ cross section measurement campaign are carried out.

Recent Results From MINERvA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patrick, Cheryl

The MINERvA detector is situated in Fermilab's NuMI beam, which provides neutrinos and antineutrinos in the 1-20 GeV range. It is designed to make precision cross-section measurements for scattering processes on various nuclei. These proceedings summarize the differential cross-section distributions measured for several different processes. Comparison of these with various models hints at additional nuclear effects not included in common simulations. These results will help constrain generators' nuclear models and reduce systematic uncertainties on their predictions. An accurate cross-section model, with minimal uncertainties, is vital to oscillation experiments.

Designing an upgrade of the Medley setup for light-ion production and fission cross-section measurements

NASA Astrophysics Data System (ADS)

Jansson, K.; Gustavsson, C.; Al-Adili, A.; Hjalmarsson, A.; Andersson-Sundén, E.; Prokofiev, A. V.; Tarrío, D.; Pomp, S.

2015-09-01

Measurements of neutron-induced fission cross-sections and light-ion production are planned in the energy range 1-40 MeV at the upcoming Neutrons For Science (NFS) facility. In order to prepare our detector setup for the neutron beam with continuous energy spectrum, a simulation software was written using the Geant4 toolkit for both measurement situations. The neutron energy range around 20 MeV is troublesome when it comes to the cross-sections used by Geant4 since data-driven cross-sections are only available below 20 MeV but not above, where they are based on semi-empirical models. Several customisations were made to the standard classes in Geant4 in order to produce consistent results over the whole simulated energy range. Expected uncertainties are reported for both types of measurements. The simulations have shown that a simultaneous precision measurement of the three standard cross-sections H(n,n), 235U(n,f) and 238U(n,f) relative to each other is feasible using a triple layered target. As high resolution timing detectors for fission fragments we plan to use Parallel Plate Avalanche Counters (PPACs). The simulation results have put some restrictions on the design of these detectors as well as on the target design. This study suggests a fissile target no thicker than 2 μm (1.7 mg/cm2) and a PPAC foil thickness preferably less than 1 μm. We also comment on the usability of Geant4 for simulation studies of neutron reactions in this energy range.

Prediction of industrial tomato hybrids from agronomic traits and ISSR molecular markers.

PubMed

Figueiredo, A S T; Resende, J T V; Faria, M V; Da-Silva, P R; Fagundes, B S; Morales, R G F

2016-05-13

Heterosis is a highly relevant phenomenon in plant breeding. This condition is usually established in hybrids derived from crosses of highly divergent parents. The success of a breeder in obtaining heterosis is directly related to the correct identification of genetically contrasting parents. Currently, the diallel cross is the most commonly used methodology to detect contrasting parents; however, it is a time- and cost-consuming procedure. Therefore, new tools capable of performing this task quickly and accurately are required. Thus, the purpose of this study was to estimate the genetic divergence in industrial tomato lines, based on agronomic traits, and to compare with estimates obtained using inter-simple sequence repeat (ISSR) molecular markers. The genetic divergence among 10 industrial tomato lines, based on nine morphological characters and 12 ISSR primers was analyzed. For data analysis, Pearson and Spearman correlation coefficients were calculated between the genetic dissimilarity measures estimated by Mahalanobis distance and Jaccard's coefficient of genetic dissimilarity from the heterosis estimates, combining ability, and means of important traits of industrial tomato. The ISSR markers efficiently detected contrasting parents for hybrid production in tomato. Parent RVTD-08 was indicated as the most divergent, both by molecular and morphological markers, that positively contributed to increased heterosis and by the specific combining ability in the crosses in which it participated. The genetic dissimilarity estimated by ISSR molecular markers aided the identification of the best hybrids of the experiment in terms of total fruit yield, pulp yield, and soluble solids content.

Structure reliability design and analysis of support ring for cylinder seal

NASA Astrophysics Data System (ADS)

Minmin, Zhao

2017-09-01

In this paper, the general reliability design process of the cross-sectional dimension of the support ring is introduced, which is used for the cylinder sealing. Then, taking a certain section shape support ring as an example, the every size parameters of section are determined from the view point of reliability design. Last, the static strength and reliability of the support ring are analyzed to verify the correctness of the reliability design result.

Cross-Sectional and Longitudinal Comparisons of Adolescent Self-Esteem.

ERIC Educational Resources Information Center

Mullis, Ann K.; And Others

1992-01-01

Examined self-esteem of adolescents over three years of high school. Ninth graders (n=270) completed Coopersmith Self-Esteem Inventory for each of three years. Found grade level significantly related to self-esteem in longitudinal but not cross-sectional design. Mediational effects of gender and socioeconomic status were found to be minimal.…

End-of-High-School Mathematics Attainment: How Did Students Get There?

ERIC Educational Resources Information Center

Newton, Xiaoxia A.

2010-01-01

Background: Many studies have looked at students' mathematics achievement in the middle and high school years and the kinds of factors that are associated with their achievement. Within this domain, however, most research utilized cross-sectional data. Cross-sectional designs have both statistical and conceptual limitations. Few studies used…

Experimental investigations of aeration efficiency in high-head gated circular conduits.

PubMed

Cihat Tuna, M; Ozkan, Fahri; Baylar, Ahmet

2014-01-01

The primary purpose of water aeration is to increase the oxygen saturation of the water. This can be achieved by using hydraulic structures because of substantial air bubble entrainment at these structures. Closed conduit aeration is a particular instance of this. While there has been a great deal of research on air-demand ratio within closed conduit, very little research has specifically addressed aeration efficiency of closed conduit. In the present work an experimental study was conducted to investigate the aeration efficiency of high-head gated circular conduits. Results showed that high-head gated circular conduits were effective for oxygen transfer. The effects of Froude number and ratio of the water cross-sectional flow area to the conduit cross-sectional area on aeration efficiency were particularly significant, whereas the effect of conduit length was only moderate. Further, a design formula for the aeration efficiency was presented relating the aeration efficiency to ratio of water cross-sectional flow area to conduit cross-sectional area and Froude number. The obtained results will be useful in future modeling processes and aid the practicing engineer in predicting aeration efficiency for design purposes.

Design of Composite Hip Prostheses Considering the Long-Term Behavior of the Femur

NASA Astrophysics Data System (ADS)

Lim, Jong Wan; Jeong, Jae Youn; Ha, Sung Kyu

A design method for the hip prosthesis is proposed which can alleviate problems associated with stress shielding, proximal loosening and the high stress of bone-implant interfaces after total hip replacement. The stress shielding which may lead to bone resorption, can cause a loosening of the stem and a fracture of femoral bone. Generally the composites were more suitable for hip prosthesis material in the long-term stability than metallic alloy because design cases of composite materials produced less stress shielding than titanium alloy. A bone remodeling algorithm was implemented in a nonlinear finite element program to predict the long-term performance of the hip prosthesis. The three neck shapes and three cross sections of composite hip were examined. It was found that the stress concentration in the distal region of the titanium stem which may cause the patient's thigh pains was reduced using composite material. The head neck shape was closely related with the cortical bone resorption and the cancellous bone apposition at proximal region whereas the cross-section was closely related with the relative micromotion between interfaces. The convex head neck type with the quadrangle cross-section produced less subsidence at proximal region on the medial side than the others. For all composite material cases, the cancellous bone apposition occurred at partial interfaces, which may result in a stable bio-fixation. The design performances of the convex neck head type with the hexagonal cross-section designed to insure the long-term stability were found to be more suitable than the others.

Designing tools for oil exploration using nuclear modeling

NASA Astrophysics Data System (ADS)

Mauborgne, Marie-Laure; Allioli, Françoise; Manclossi, Mauro; Nicoletti, Luisa; Stoller, Chris; Evans, Mike

2017-09-01

When designing nuclear tools for oil exploration, one of the first steps is typically nuclear modeling for concept evaluation and initial characterization. Having an accurate model, including the availability of accurate cross sections, is essential to reduce or avoid time consuming and costly design iterations. During tool response characterization, modeling is benchmarked with experimental data and then used to complement and to expand the database to make it more detailed and inclusive of more measurement environments which are difficult or impossible to reproduce in the laboratory. We present comparisons of our modeling results obtained using the ENDF/B-VI and ENDF/B-VII cross section data bases, focusing on the response to a few elements found in the tool, borehole and subsurface formation. For neutron-induced inelastic and capture gamma ray spectroscopy, major obstacles may be caused by missing or inaccurate cross sections for essential materials. We show examples of the benchmarking of modeling results against experimental data obtained during tool characterization and discuss observed discrepancies.

Predictions of a Supersonic Jet-in-Crossflow: Comparisons Among CFD Solvers and with Experiment

DTIC Science & Technology

2014-09-01

The transverse supersonic jet was produced using a converging-diverging nozzle with a design Mach number of 3.73, a conical expansion section half...J. F., and Erven, R. J., “Flow Separation Inside a Supersonic Nozzle Exhausting into a Subsonic Compressible Crossflw, “Journal of Propulsion and...Predictions of a Supersonic Jet-in-Crossflow: Comparisons Among CFD Solvers and with Experiment by James DeSpirito, Kevin D Kennedy, Clark

Direct Reactions at the Facility for Experiments on Nuclear Reactions in Stars (FENRIS)

NASA Astrophysics Data System (ADS)

Longland, Richard; Kelley, John; Marshall, Caleb; Portillo, Federico; Setoodehnia, Kiana

2017-09-01

Nuclear cross sections are a key ingredient in stellar models designed to understand how stars evolve. Determining these cross sections, therefore, is critical for obtaining reliable predictions from stellar models. While many charged-particle reaction cross sections can be measured in the laboratory, the Coulomb barrier means that they cannot always be measured at the low energies relevant to astrophysics. In other cases, radioactive targets make the measurements unfeasible. Radioactive ion beam experiments in inverse kinematics are one solution, but low beam intensities mean that cross sections plague these attempts further. Direct measurements, particularly particle transfer experiments, are one tool in our inventory that provides us with the necessary information to infer reaction cross sections at stellar energies. I will present an overview of one facility: the Facility for Experiments on Nuclear Reactions in Stars (FENRIS), which is dedicated to performing particle transfer measurements for astrophysical cross sections. Over the past few years, FENRIS has been fully upgraded and characterized. I will show highlights of our upgrade activities and current capabilities. I will also highlight our recent experimental results and discuss current upgrade efforts.

Farsi version of social skills rating system-secondary student form: cultural adaptation, reliability and construct validity.

PubMed

Eslami, Ahmad Ali; Amidi Mazaheri, Maryam; Mostafavi, Firoozeh; Abbasi, Mohamad Hadi; Noroozi, Ensieh

2014-01-01

Assessment of social skills is a necessary requirement to develop and evaluate the effectiveness of cognitive and behavioral interventions. This paper reports the cultural adaptation and psychometric properties of the Farsi version of the social skills rating system-secondary students form (SSRS-SS) questionnaire (Gresham and Elliot, 1990), in a normative sample of secondary school students. A two-phase design was used that phase 1 consisted of the linguistic adaptation and in phase 2, using cross-sectional sample survey data, the construct validity and reliability of the Farsi version of the SSRS-SS were examined in a sample of 724 adolescents aged from 13 to 19 years. Content validity index was excellent, and the floor/ceiling effects were low. After deleting five of the original SSRS-SS items, the findings gave support for the item convergent and divergent validity. Factor analysis revealed four subscales. RESULTS showed good internal consistency (0.89) and temporal stability (0.91) for the total scale score. Findings demonstrated support for the use of the 27-item Farsi version in the school setting. Directions for future research regarding the applicability of the scale in other settings and populations of adolescents are discussed.

[IBEAS design: adverse events prevalence in Latin American hospitals].

PubMed

Aranaz-Andrés, J M; Aibar-Remón, C; Limón-Ramírez, R; Amarilla, A; Restrepo, F R; Urroz, O; Sarabia, O; Inga, R; Santivañez, A; Gonseth-García, J; Larizgoitia-Jauregui, I; Agra-Varela, Y; Terol-García, E

2011-01-01

To describe the methodological characteristics of the IBEAS study: adverse events prevalence in Latin American hospitals, with the aim of analysing the magnitude, significance and impact of adverse events (AE); to identify the main problems associated with patient safety AE; to increase the capacity of professionals involved in patient safety; and the setting up of patient safety agendas in the participating countries. A patient safety study launched in 35 Latin American hospitals through the analysis of AE in 5 countries: Argentina, Colombia, Costa Rica, Mexico and Peru, using a cross-sectional study using a review of clinical records as the main method. The implications of using a cross-sectional design when studying AE are described, in terms of resources required, internal validity and usefulness related to risk management. The cross-sectional design seems an efficient methodology in terms of time and resources spent, as well as being easy to carry out. Although the cross-sectional design does not review the all hospital episodes, it is able to provide a reliable estimate of prevalence and to support a surveillance system. Because of a possible survival bias, it is likely that the AE which led to hospital admissions will be overestimated, as well as the health related infections or those adverse events which are difficult to identify if the patient is not examined (e.g. contusions). Communication with the ward staff (if the patient is still hospitalised) help in finding the causality and their prevention. Copyright © 2010 SECA. Published by Elsevier Espana. All rights reserved.

Long bone robustness during growth: A cross-sectional pQCT examination of children and young adults aged 5-29years.

PubMed

Rantalainen, Timo; Weeks, Benjamin K; Nogueira, Rossana C; Beck, Belinda R

2016-12-01

Skeletal robustness (cross-section size relative to length) is associated with stress fractures in adults, and appears to explain the high incidence of distal radius fractures in adolescents. However, little is known about the ontogeny of long bone robustness during the first three decades of life. Therefore, we explored the ontogeny of tibial, fibular, ulnar and radial robustness in a cross-sectional sample of 5 to 29year-old volunteers of both sexes. Peripheral quantitative computed tomography (pQCT) was used to evaluate cross-sections of the leg (4%, 14%, 38% and 66%), and forearm (4%, and 66%) in N=432 individuals. Robustness was evaluated as the total bone area divided by bone length. Differences between age-groups, sexes, and age-group×sex interactions were evaluated with ANOVA with Tukey's post hocs where appropriate. Most bone sites exhibited more robust bones in men than women (P<0.001 to 0.02), and in older age-groups than younger (P<0.001). Sex×age-group interaction was observed at the 66% and 38% tibia sites with robustness increasing more with age in men than in women (P=0.006 to 0.042). Post-hoc analyses indicated no sex differences prior to 13years-of-age, and notable exceptions to increasing robustness with age at the 4% radial and 66% tibial sites, which exhibited reduced robustness in age groups close to peak height velocity. In conclusion, the present results suggest that very little sexual dimorphism in long bone robustness exists prior to puberty, and that divergence occurs primarily after cessation of longitudinal growth. A period of relative diaphyseal slenderness was identified at age-groups coinciding with the adolescent growth spurt, which may be related to the relatively high incidence of frank and stress fracture in adolescents. Copyright © 2016 Elsevier Inc. All rights reserved.

Cross Section Sensitivity and Propagated Errors in HZE Exposures

NASA Technical Reports Server (NTRS)

Heinbockel, John H.; Wilson, John W.; Blatnig, Steve R.; Qualls, Garry D.; Badavi, Francis F.; Cucinotta, Francis A.

2005-01-01

It has long been recognized that galactic cosmic rays are of such high energy that they tend to pass through available shielding materials resulting in exposure of astronauts and equipment within space vehicles and habitats. Any protection provided by shielding materials result not so much from stopping such particles but by changing their physical character in interaction with shielding material nuclei forming, hopefully, less dangerous species. Clearly, the fidelity of the nuclear cross-sections is essential to correct specification of shield design and sensitivity to cross-section error is important in guiding experimental validation of cross-section models and database. We examine the Boltzmann transport equation which is used to calculate dose equivalent during solar minimum, with units (cSv/yr), associated with various depths of shielding materials. The dose equivalent is a weighted sum of contributions from neutrons, protons, light ions, medium ions and heavy ions. We investigate the sensitivity of dose equivalent calculations due to errors in nuclear fragmentation cross-sections. We do this error analysis for all possible projectile-fragment combinations (14,365 such combinations) to estimate the sensitivity of the shielding calculations to errors in the nuclear fragmentation cross-sections. Numerical differentiation with respect to the cross-sections will be evaluated in a broad class of materials including polyethylene, aluminum and copper. We will identify the most important cross-sections for further experimental study and evaluate their impact on propagated errors in shielding estimates.

Transverse momentum dependent fragmenting jet functions with applications to quarkonium production

DOE PAGES

Bain, Reggie; Makris, Yiannis; Mehen, Thomas

2016-11-23

We introduce the transverse momentum dependent fragmenting jet function (TMDFJF), which appears in factorization theorems for cross sections for jets with an identified hadron. These are functions of z, the hadron’s longitudinal momentum fraction, and transverse momentum, p ⊥, relative to the jet axis. In the framework of Soft-Collinear Effective Theory (SCET) we derive the TMDFJF from both a factorized SCET cross section and the TMD fragmentation function defined in the literature. The TMDFJFs are factorized into distinct collinear and soft-collinear modes by matching onto SCET +. As TMD calculations contain rapidity divergences, both the renormalization group (RG) and rapiditymore » renormalization group (RRG) must be used to provide resummed calculations with next-to-leading-logarithm prime (NLL’) accuracy. We apply our formalism to the production of J/ψ within jets initiated by gluons. In this case the TMDFJF can be calculated in terms of NRQCD (Non-relativistic quantum chromodynamics) fragmentation functions. We find that when the J/ψ carries a significant fraction of the jet energy, the p T and z distributions differ for different NRQCD production mechanisms. Another observable with discriminating power is the average angle that the J/ψ makes with the jet axis.« less

Power Enhancement in High Dimensional Cross-Sectional Tests

PubMed Central

Fan, Jianqing; Liao, Yuan; Yao, Jiawei

2016-01-01

We propose a novel technique to boost the power of testing a high-dimensional vector H : θ = 0 against sparse alternatives where the null hypothesis is violated only by a couple of components. Existing tests based on quadratic forms such as the Wald statistic often suffer from low powers due to the accumulation of errors in estimating high-dimensional parameters. More powerful tests for sparse alternatives such as thresholding and extreme-value tests, on the other hand, require either stringent conditions or bootstrap to derive the null distribution and often suffer from size distortions due to the slow convergence. Based on a screening technique, we introduce a “power enhancement component”, which is zero under the null hypothesis with high probability, but diverges quickly under sparse alternatives. The proposed test statistic combines the power enhancement component with an asymptotically pivotal statistic, and strengthens the power under sparse alternatives. The null distribution does not require stringent regularity conditions, and is completely determined by that of the pivotal statistic. As specific applications, the proposed methods are applied to testing the factor pricing models and validating the cross-sectional independence in panel data models. PMID:26778846

Simulation of High Power Lasers (Preprint)

DTIC Science & Technology

2010-06-01

integration, which requires communication of zonal boundary information after each inner- iteration of the Gauss - Seidel or Jacobi matrix solver. Each...experiment consisting of a supersonic (M~2.2) converging -diverging nozzle section with secondary mass injection in the nozzle expansion downstream of...consists of a section of a supersonic (M~2.2) converging -diverging slit nozzle with one large and two small orifices that inject reactants into the

Fluidically Augmented Nozzles for Pulse Detonation Engine Applications

DTIC Science & Technology

2011-12-01

25 captured the flow soon after the leading shock wave passed through the diverging section of the nozzle. As can be seen, the “pillow” has begun to...35 Figure 25. Initial Detonation Wave Enters the Diverging Section of the Nozzle...charging the combustor with an appropriate fuel/air mixture. This mixture is then ignited, producing a flame that is initially a deflagration wave . A

Dynamic Bayesian Networks as a Probabilistic Metamodel for Combat Simulations

DTIC Science & Technology

2014-09-18

test is commonly used for large data sets and is the method of comparison presented in Section 5.5. 4.3.3 Kullback - Leibler Divergence Goodness of Fit ...methods exist that might improve the results. A goodness of fit test using the Kullback - Leibler Divergence was proposed in the first paper, but still... Kullback - Leibler Divergence Goodness of Fit Test . . .

Soft-photon emission effects and radiative corrections for electromagnetic processes at very high energies

NASA Technical Reports Server (NTRS)

Gould, R. J.

1979-01-01

Higher-order electromagnetic processes involving particles at ultrahigh energies are discussed, with particular attention given to Compton scattering with the emission of an additional photon (double Compton scattering). Double Compton scattering may have significance in the interaction of a high-energy electron with the cosmic blackbody photon gas. At high energies the cross section for double Compton scattering is large, though this effect is largely canceled by the effects of radiative corrections to ordinary Compton scattering. A similar cancellation takes place for radiative pair production and the associated radiative corrections to the radiationless process. This cancellation is related to the well-known cancellation of the infrared divergence in electrodynamics.

Origin of storm footprints on the sea seen by synthetic aperture radar.

PubMed

Atlas, D

1994-11-25

Spaceborne synthetic aperture radar can detect storm footprints on the sea. Coastal weather radar from Cape Hatteras provides evidence that the echo-free hole at the footprint core is the result of wave damping by rain. The increased radar cross section of the sea surrounding the echo-free hole results from the divergence of the precipitation-forced downdraft impacting the sea. The footprint boundary is the gust front; its oriention is aligned with the direction of the winds aloft, which are transported down with the downdraft, and its length implies downdraft impact 1 hour earlier at a quasi-stationary impact spot. The steady, localized nature of the storm remains a mystery.

Identification of evolutionary hotspots based on genetic data from multiple terrestrial and aquatic taxa and gap analysis of hotspots in protected lands encompassed by the South Atlantic Landscape Conservation Cooperative.

USGS Publications Warehouse

Robinson, J.; Snider, M.; Duke, J.; Moyer, G.R.

2014-01-01

 The southeastern United States is a recognized hotspot of biodiversity for a variety of aquatic taxa, including fish, amphibians, and mollusks. Unfortunately, the great diversity of the area is accompanied by a large proportion of species at risk of extinction . Gap analysis was employed to assess the representation of evolutionary hotspots in protected lands w h ere an evolutionary hotspot was defined as an area with high evolutionary potential and measured by atypical patterns of genetic divergence, genetic diversity, and to a lesser extent genetic similarity across multiple terrestrial or aquatic taxa. A survey of the primary literature produced 16 terrestrial and 14 aquatic genetic datasets for estimation of genetic divergence and diversity. Relative genetic diversity and divergence values for each terrestrial and aquatic dataset were used for interpolation of multispecies genetic surfaces and subsequent visualization using ArcGIS. The multispecies surfaces interpolated from relative divergences and diversity data identified numerous evolutionary hotspots for both terrestrial and aquatic taxa , many of which were afforded some current protection. For instance, 14% of the cells identified as hotspots of aquatic diversity were encompassed by currently protected areas. Additionally, 25% of the highest 1% of terrestrial diversity cells were afforded some level of protection. In contrast, areas of high and low divergence among species, and areas of high variance in diversity were poorly represented in the protected lands. Of particular interest were two areas that were consistently identified by several different measures as important from a conservation perspective. These included an area encompassing the panhandle of Florida and southern Georgia near the Apalachicola National Forest (displaying varying levels of genetic divergence and greater than average levels of genetic diversity) and a large portion of the coastal regions of North and South Carolina (displaying low genetic divergence and greater than average levels of genetic diversity) . Our results show the utility o f genetic data sets for identifying cross - species patterns of genetic  diversity and divergence (i.e., evolutionary hotspots) in aquatic and terrestrial environments for use in conservation design and delivery across the southeastern United States. 

Simple, empirical approach to predict neutron capture cross sections from nuclear masses

NASA Astrophysics Data System (ADS)

Couture, A.; Casten, R. F.; Cakirli, R. B.

2017-12-01

Background: Neutron capture cross sections are essential to understanding the astrophysical s and r processes, the modeling of nuclear reactor design and performance, and for a wide variety of nuclear forensics applications. Often, cross sections are needed for nuclei where experimental measurements are difficult. Enormous effort, over many decades, has gone into attempting to develop sophisticated statistical reaction models to predict these cross sections. Such work has met with some success but is often unable to reproduce measured cross sections to better than 40 % , and has limited predictive power, with predictions from different models rapidly differing by an order of magnitude a few nucleons from the last measurement. Purpose: To develop a new approach to predicting neutron capture cross sections over broad ranges of nuclei that accounts for their values where known and which has reliable predictive power with small uncertainties for many nuclei where they are unknown. Methods: Experimental neutron capture cross sections were compared to empirical mass observables in regions of similar structure. Results: We present an extremely simple method, based solely on empirical mass observables, that correlates neutron capture cross sections in the critical energy range from a few keV to a couple hundred keV. We show that regional cross sections are compactly correlated in medium and heavy mass nuclei with the two-neutron separation energy. These correlations are easily amenable to predict unknown cross sections, often converting the usual extrapolations to more reliable interpolations. It almost always reproduces existing data to within 25 % and estimated uncertainties are below about 40 % up to 10 nucleons beyond known data. Conclusions: Neutron capture cross sections display a surprisingly strong connection to the two-neutron separation energy, a nuclear structure property. The simple, empirical correlations uncovered provide model-independent predictions of neutron capture cross sections, extending far from stability, including for nuclei of the highest sensitivity to r -process nucleosynthesis.

Stress state estimation in multilayer support of vertical shafts, considering off-design cross-sectional deformation

NASA Astrophysics Data System (ADS)

Antsiferov, SV; Sammal, AS; Deev, PV

2018-03-01

To determine the stress-strain state of multilayer support of vertical shafts, including cross-sectional deformation of the tubing rings as against the design, the authors propose an analytical method based on the provision of the mechanics of underground structures and surrounding rock mass as the elements of an integrated deformable system. The method involves a rigorous solution of the corresponding problem of elasticity, obtained using the mathematical apparatus of the theory of analytic functions of a complex variable. The design method is implemented as a software program allowing multivariate applied computation. Examples of the calculation are given.

PBL and Critical Thinking Disposition in Chinese Medical Students--A Randomized Cross-Sectional Study

ERIC Educational Resources Information Center

Du, XiangYun; Emmersen, Jeppe; Toft, Egon; Sun, Baozhi

2013-01-01

The purpose of this study was to explore the relationship of problem-based learning (PBL) and the development of critical thinking disposition (CT) and academic achievement in Chinese medical students using a cross-sectional randomized design. Medical students from China Medical University (CMU) were randomized to PBL or non-PBL teaching at the…

Factors Associated with Women's Antenatal Plans to Use a Baby Walker: A Cross Sectional Study

ERIC Educational Resources Information Center

Illingworth, Rachel; Kendrick, Denise; Collier, Jacqueline; Woods, Amanda; Wattse, Kim; Dewey, Michael; Chen, Chih-Mei

2006-01-01

Objective: The objective of these analyses was to explore maternal antenatal decisions about baby walker use, factors associated with these decisions and the relationship between antenatal plans to use a walker and postnatal walker use. Design: Cross sectional study. Setting: Mothers-to-be (n = 1174) participating in a cluster randomised…

Psychological Problems in Children with Cerebral Palsy: A Cross-Sectional European Study

ERIC Educational Resources Information Center

Parkes, Jackie; White-Koning, Melanie; Dickinson, Heather O.; Thyen, Ute; Arnaud, Catherine; Beckung, Eva; Fauconnier, Jerome; Marcelli, Marco; McManus, Vicki; Michelsen, Susan I.; Parkinson, Kathryn; Colver, Allan

2008-01-01

Objectives: To describe psychological symptoms in 8-12-year-old children with cerebral palsy; to investigate predictors of these symptoms and their impact on the child and family. Design: A cross-sectional multi-centre survey. Participants: Eight hundred and eighteen children with cerebral palsy, aged 8-12 years, identified from population-based…

Medical Students' Attitudes towards Peer Physical Examination: Findings from an International Cross-Sectional and Longitudinal Study

ERIC Educational Resources Information Center

Rees, Charlotte E.; Wearn, Andy M.; Vnuk, Anna K.; Sato, Toshio J.

2009-01-01

Although studies have begun to shed light on medical students' attitudes towards peer physical examination (PPE), they have been conducted at single sites, and have generally not examined changes in medical students' attitudes over time. Employing both cross-sectional and longitudinal designs, the current study examines medical students' attitudes…

Design of the Cross Section Shape of AN Aluminum Crash Box for Crashworthiness Enhancement of a CAR

NASA Astrophysics Data System (ADS)

Kim, S. B.; Huh, H.; Lee, G. H.; Yoo, J. S.; Lee, M. Y.

This paper deals with the crashworthiness of an aluminum crash box for an auto-body with the various shapes of cross section such as a rectangle, a hexagon and an octagon. First, crash boxes with various cross sections were tested with numerical simulation to obtain the energy absorption capacity and the mean load. In case of the simple axial crush, the octagon shape shows higher mean load and energy absorption than the other two shapes. Secondly, the crash boxes were assembled to a simplified auto-body model for the overall crashworthiness. The model consists of a bumper, crash boxes, front side members and a sub-frame representing the behavior of a full car at the low speed impact. The analysis result shows that the rectangular cross section shows the best performance as a crash box which deforms prior to the front side member. The hexagonal and octagonal cross sections undergo torsion and local buckling as the width of cross section decreases while the rectangular cross section does not. The simulation result of the rectangular crash box was verified with the experimental result. The simulation result shows close tendency in the deformed shape and the load-displacement curve to the experimental result.

A Cross-Cultural Study of Task Specificity in Creativity

ERIC Educational Resources Information Center

Storme, Martin; Lubart, Todd; Myszkowski, Nils; Cheung, Ping Chung; Tong, Toby; Lau, Sing

2017-01-01

This study provides new evidence concerning task specificity in creativity--examining through a cross-cultural perspective the extent to which performance in graphic versus verbal creativity tasks (domain specificity) and in divergent versus convergent creativity tasks (process specificity) are correlated. The relations between different…

Influence of cross-sectional design and dimension on mechanical behavior of nickel-titanium instruments under torsion and bending: a numerical analysis.

PubMed

Zhang, En-Wei; Cheung, Gary S P; Zheng, Yu-Feng

2010-08-01

The aim of this study was to examine the influence of the cross-sectional configuration and dimensions (size and taper) on the torsional and bending behavior of nickel-titanium rotary instruments, taking into account the nonlinear mechanical properties of material. Ten cross-sectional configurations, square, triangular, U-type, S-type (large and small), convex-triangle, and 4 proprietary ones (Mani NRT and RT2, Quantec, and Mtwo), were analyzed under torsion or bending by using a 3-dimensional finite element method. The von Mises stresses were correlated with the critical values for various phases of the nickel-titanium material. Different loading conditions led to unequal patterns of stress distribution. Increasing the applied torque or bending angle resulted in a rise in the corresponding stresses in the instrument. Favorable stress distribution without dangerous stress concentration was observed if the material was undergoing superelastic transformation at that applied load. The ultimate strength of the material was not exceeded when the instrument was bent up to a 50-degree curvature. On the other hand, when a torsional moment of greater than 1.0 N*mm was applied, the maximum stresses developed in some designs would exceed the ultimate strength of the material. Little variation in the von Mises stresses was observed for instruments of different nominal sizes and tapers on bending to similar extent. The cross-sectional design has a greater impact than taper or size of the instrument on the stresses developed in the instrument under either torsion or bending. Certain cross-sectional configurations are prone to fracture by excess torsional stresses. Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

[Saarland Growth Study: sampling design].

PubMed

Danker-Hopfe, H; Zabransky, S

2000-01-01

The use of reference data to evaluate the physical development of children and adolescents is part of the daily routine in the paediatric ambulance. The construction of such reference data is based on the collection of extensive reference data. There are different kinds of reference data: cross sectional references, which are based on data collected from a big representative cross-sectional sample of the population, longitudinal references, which are based on follow-up surveys of usually smaller samples of individuals from birth to maturity, and mixed longitudinal references, which are a combination of longitudinal and cross-sectional reference data. The advantages and disadvantages of the different methods of data collection and the resulting reference data are discussed. The Saarland Growth Study was conducted for several reasons: growth processes are subject to secular changes, there are no specific reference data for children and adolescents from this part of the country and the growth charts in use in the paediatric praxis are possibly not appropriate any more. Therefore, the Saarland Growth Study served two purposes a) to create actual regional reference data and b) to create a database for future studies on secular trends in growth processes of children and adolescents from Saarland. The present contribution focusses on general remarks on the sampling design of (cross-sectional) growth surveys and its inferences for the design of the present study.

An experimental evaluation of S-duct inlet-diffuser configurations for turboprop offset gearbox applications

NASA Technical Reports Server (NTRS)

Mcdill, Paul L.

1986-01-01

A test program, utilizing a large scale model, was run in the NASA Lewis Research Center 10- by 10-ft wind tunnel to examine the influence on performance of design parameters of turboprop S-duct inlet/diffuser systems. The parametric test program investigated inlet lip thickness, inlet/diffuser cross-sectional geometry, throat design Mach number, and shaft fairing shape. The test program was run at angles of attack to 15 deg and tunnel Mach numbers to 0.35. Results of the program indicate that current design techniques can be used to design inlet/diffuser systems with acceptable total pressure recovery, but several of the design parameters, notably lip thickness (contraction ratio) and shaft fairing cross section, must be optimized to prevent excessive distortion at the compressor face.

One-group fission cross sections for plutonium and minor actinides inserted in calculated neutron spectra of fast reactor cooled with lead-208 or lead-bismuth eutectic

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khorasanov, G. L.; Blokhin, A. I.

The paper is dedicated to one-group fission cross sections of Pu and MA in LFRs spectra with the aim to increase these values by choosing a coolant which hardens neutron spectra. It is shown that replacement of coolant from Pb-Bi with Pb-208 in the fast reactor RBEC-M, designed in Russia, leads to increasing the core mean neutron energy. As concerns fuel Pu isotopes, their one-group fission cross sections become slightly changed, while more dramatically Am-241 one-group fission cross section is changed. Another situation occurs in the lateral blanket containing small quantities of minor actinides. It is shown that as amore » result of lateral blanket mean neutron energy hardening the one-group fission cross sections of Np-237, Am-241 and Am-243 increases up to 8-11%. This result allows reducing the time of minor actinides burning in FRs. (authors)« less

Experimental Crossing of Two Distinct Species of Leopard Geckos, Eublepharis angramainyu and E. macularius: Viability, Fertility and Phenotypic Variation of the Hybrids

PubMed Central

Jančúchová-Lásková, Jitka; Landová, Eva; Frynta, Daniel

2015-01-01

Hybridization between distinct species of animals and subsequent genetic introgression plays a considerable role in the speciation process and the emergence of adaptive characters. Fitness of between-species hybrids usually sharply decreases with the divergence time of the concerned species and the divergence depth, which still allows for a successful crossing differs among principal clades of vertebrates. Recently, a review of hybridization events among distinct lizard species revealed that lizards belong to vertebrates with a highly developed ability to hybridize. In spite of this, reliable reports of experimental hybridizations between genetically fairly divergent species are only exceptional. Here, we show the results of the crossing of two distinct allopatric species of eyelid geckos possessing temperature sex determination and lacking sex chromosomes: Eublepharis macularius distributed in Pakistan/Afghanistan area and E. angramainyu, which inhabits Mesopotamia and adjacent areas. We demonstrated that F1 hybrids were viable and fertile, and the introgression of E. angramainyu genes into the E. macularius genome can be enabled via a backcrossing. The examined hybrids (except those of the F2 generation) displayed neither malformations nor a reduced survival. Analyses of morphometric and coloration traits confirmed phenotypic distinctness of both parental species and their F1 hybrids. These findings contrast with long-term geographic and an evolutionary separation of the studied species. Thus, the occurrence of fertile hybrids of comparably divergent species, such as E. angramainyu and E. macularius, may also be expected in other taxa of squamates. This would violate the current estimates of species diversity in lizards. PMID:26633648

Cross-Informant Agreement and Stability of the Strengths and Difficulties Questionnaire among Finnish Mainstream and Special Education Students

ERIC Educational Resources Information Center

Lappalainen, Kristiina; Savolainen, Hannu; Sointu, Erkko T.; Epstein, Michael H.

2014-01-01

This study investigated the cross-informant agreement among student self-report, teacher report, and parent report on the Strengths and Difficulties Questionnaire translated into Finnish (SDQ-Fin) and estimated mean convergent and divergent correlations with a sample of fifth-grade Finnish students (N = 588) and the cross-informant agreement among…

Arcjet nozzle design impacts

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Sovie, Amy J.; Haag, Thomas W.

1989-01-01

The effect of nozzle configuration on the operating characteristics of a low power dc arcjet thruster was determined. A conical nozzle with a 30 deg converging angle, a 20 deg diverging angle, and an area ratio of 225 served as the baseline case. Variations on the geometry included bell-shaped contours both up and downstream, and a downstream trumpet-shaped contour. The nozzles were operated over a range of specific power near that anticipated for on-orbit operation. Mass flow rate, thrust, current, and voltage were monitored to provide accurate comparisons between nozzles. The upstream contour was found to have minimal effect on arcjet operation. It was determined that the contour of the divergent section of the nozzle, that serves as the anode, was very important in determining the location of arc attachment, and thus had a significant impact on arcjet performance. The conical nozzle was judged to have the optimal current/voltage characteristics and produced the best performance of the nozzles tested.

Arcjet Nozzle Design Impacts

NASA Technical Reports Server (NTRS)

Curran, Francis M.; Sovie, Amy J.; Haag, Thomas W.

1989-01-01

The effect of nozzle configuration on the operating characteristics of a low power dc arcjet thruster was determined. A conical nozzle with a 30 deg converging angle, a 20 deg diverging angle, and an area ratio of 225 served as the baseline case. Variations on the geometry included bell-shaped contours both up and downstream, and a downstream trumpet-shaped contour. The nozzles were operated over a range of specific power near that anticipated for on-orbit operation. Mass flow rate, thrust, current, and voltage were monitored to provide accurate comparisons between nozzles. The upstream contour was found to have minimal effect on arcjet operation. It was determined that the contour of the divergent section of the nozzle, that serves as the anode, was very important in determining the location of arc attachment, and thus had a significant impact on arcjet performance. The conical nozzle was judged to have the optimal current/voltage characteristics and produced the best performance of the nozzles tested.

Optimal Shakedown of the Thin-Wall Metal Structures Under Strength and Stiffness Constraints

NASA Astrophysics Data System (ADS)

Alawdin, Piotr; Liepa, Liudas

2017-06-01

Classical optimization problems of metal structures confined mainly with 1st class cross-sections. But in practice it is common to use the cross-sections of higher classes. In this paper, a new mathematical model for described shakedown optimization problem for metal structures, which elements are designed from 1st to 4th class cross-sections, under variable quasi-static loads is presented. The features of limited plastic redistribution of forces in the structure with thin-walled elements there are taken into account. Authors assume the elastic-plastic flexural buckling in one plane without lateral torsional buckling behavior of members. Design formulae for Methods 1 and 2 for members are analyzed. Structures stiffness constrains are also incorporated in order to satisfy the limit serviceability state requirements. With the help of mathematical programming theory and extreme principles the structure optimization algorithm is developed and justified with the numerical experiment for the metal plane frames.

Cross-Situational Word Learning in the Right Situations

ERIC Educational Resources Information Center

Dautriche, Isabelle; Chemla, Emmanuel

2014-01-01

Upon hearing a novel word, language learners must identify its correct meaning from a diverse set of situationally relevant options. Such referential ambiguity could be reduced through "repetitive" exposure to the novel word across diverging learning situations, a learning mechanism referred to as "cross-situational learning."…

78 FR 909 - Further Proposed Guidance Regarding Compliance With Certain Swap Regulations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-07

... establish a new regulatory framework for swaps. The legislation was enacted to reduce systemic risk... increase understanding of each other's regulatory approaches and to harmonize the cross-border approaches... may lead to divergent approaches to cross-border activities. The Commission also recognizes the...

Age Differences in the Monitoring of Learning: Cross-Sectional Evidence of Spared Resolution across the Adult Life Span

ERIC Educational Resources Information Center

Hertzog, Christopher; Sinclair, Starlette M.; Dunlosky, John

2010-01-01

Researchers of metacognitive development in adulthood have exclusively used extreme-age-groups designs. We used a full cross-sectional sample (N = 285, age range: 18-80) to evaluate how associative relatedness and encoding strategies influence judgments of learning (JOLs) in adulthood. Participants studied related and unrelated word pairs and made…

Adolescent Idiopathic Scoliosis and Eating Disorders: Is There a Relation? Results of a Cross-Sectional Study

ERIC Educational Resources Information Center

Zaina, Fabio; Donzelli, Sabrina; Lusini, Monia; Vismara, Luca; Capodaglio, Paolo; Neri, Laura; Negrini, Stefano

2013-01-01

A recent study suggests a correlation between idiopathic scoliosis in adolescence and eating disorders. However, this does not correspond with our clinical experience in the same population. The aim of this study was to verify the correlation between scoliosis and eating disorders in adolescence. A cross-sectional study was designed including 187…

The Effect of Using Dynamic Mathematics Software: Cross Section and Visualization

ERIC Educational Resources Information Center

Kösa, Temel

2016-01-01

The main purpose of this study is to determine the effects of using dynamic mathematics software on pre-service mathematics teachers' ability to infer the shape of a cross section of a three-dimensional solid, as well as on their spatial visualization skills. The study employed a quasi-experimental design with a control group; the Purdue Spatial…

C+C Fusion Cross Sections Measurements for Nuclear Astrophysics

DOE PAGES

Almaraz-Calderon, S.; Carnelli, P. F. F.; Rehm, K. E.; ...

2015-06-02

Total fusion cross section of carbon isotopes were obtained using the newly developed MUSIC detector. MUSIC is a highly efficient, active target-detector system designed to measure fusion excitation functions with radioactive beams. The present measurements are relevant for understanding x-ray superbursts. The results of the first MUSIC campaign as well as the astrophysical implications are presented in this work.

C+C Fusion Cross Sections Measurements for Nuclear Astrophysics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Almaraz-Calderon, S.; Carnelli, P. F. F.; Rehm, K. E.

Total fusion cross section of carbon isotopes were obtained using the newly developed MUSIC detector. MUSIC is a highly efficient, active target-detector system designed to measure fusion excitation functions with radioactive beams. The present measurements are relevant for understanding x-ray superbursts. The results of the first MUSIC campaign as well as the astrophysical implications are presented in this work.

3D Measurement of Anatomical Cross-sections of Foot while Walking

NASA Astrophysics Data System (ADS)

Kimura, Makoto; Mochimaru, Masaaki; Kanade, Takeo

Recently, techniques for measuring and modeling of human body are taking attention, because human models are useful for ergonomic design in manufacturing. We aim to measure accurate shape of human foot that will be useful for the design of shoes. For such purpose, shape measurement of foot in motion is obviously important, because foot shape in the shoe is deformed while walking or running. In this paper, we propose a method to measure anatomical cross-sections of foot while walking. No one had ever measured dynamic shape of anatomical cross-sections, though they are very basic and popular in the field of biomechanics. Our proposed method is based on multi-view stereo method. The target cross-sections are painted in individual colors (red, green, yellow and blue), and the proposed method utilizes the characteristic of target shape in the camera captured images. Several nonlinear conditions are introduced in the process to find the consistent correspondence in all images. Our desired accuracy is less than 1mm error, which is similar to the existing 3D scanners for static foot measurement. In our experiments, the proposed method achieved the desired accuracy.

Highly conserved Z and molecularly diverged W chromosomes in the fish genus Triportheus (Characiformes, Triportheidae).

PubMed

Yano, C F; Bertollo, L A C; Ezaz, T; Trifonov, V; Sember, A; Liehr, T; Cioffi, M B

2017-03-01

The main objectives of this study were to test: (1) whether the W-chromosome differentiation matches to species' evolutionary divergence (phylogenetic concordance) and (2) whether sex chromosomes share a common ancestor within a congeneric group. The monophyletic genus Triportheus (Characiformes, Triportheidae) was the model group for this study. All species in this genus so far analyzed have ZW sex chromosome system, where the Z is always the largest chromosome of the karyotype, whereas the W chromosome is highly variable ranging from almost homomorphic to highly heteromorphic. We applied conventional and molecular cytogenetic approaches including C-banding, ribosomal DNA mapping, comparative genomic hybridization (CGH) and cross-species whole chromosome painting (WCP) to test our questions. We developed Z- and W-chromosome paints from T. auritus for cross-species WCP and performed CGH in a representative species (T. signatus) to decipher level of homologies and rates of differentiation of W chromosomes. Our study revealed that the ZW sex chromosome system had a common origin, showing highly conserved Z chromosomes and remarkably divergent W chromosomes. Notably, the W chromosomes have evolved to different shapes and sequence contents within ~15-25 Myr of divergence time. Such differentiation highlights a dynamic process of W-chromosome evolution within congeneric species of Triportheus.

Rapid evolution of asymmetric reproductive incompatibilities in stalk-eyed flies.

PubMed

Rose, Emily G; Brand, Cara L; Wilkinson, Gerald S

2014-02-01

The steps by which isolated populations acquire reproductive incompatibilities remain poorly understood. One potentially important process is postcopulatory sexual selection because it can generate divergence between populations in traits that influence fertilization success after copulation. Here we present a comprehensive analysis of this form of reproductive isolation by conducting reciprocal crosses between variably diverged populations of stalk-eyed flies (Teleopsis dalmanni). First, we measure seven types of reproductive incompatibility between copulation and fertilization. We then compare fertilization success to hatching success to quantify hybrid inviability. Finally, we determine if sperm competition acts to reinforce or counteract any incompatibilities. We find evidence for multiple incompatibilities in most crosses, including failure to store sperm after mating, failure of sperm to reach the site of fertilization, failure of sperm to fertilize eggs, and failure of embryos to develop. Local sperm have precedence over foreign sperm, but this effect is due mainly to differences in sperm transfer and reduced hatching success. Crosses between recently diverged populations are asymmetrical with regard to the degree and type of incompatibility. Because sexual conflict in these flies is low, postcopulatory sexual selection, rather than antagonistic coevolution, likely causes incompatibilities due to mismatches between male and female reproductive traits. © 2013 The Author(s). Evolution © 2013 The Society for the Study of Evolution.

Analysis of Femoral Components of Cemented Total Hip Arthroplasty

NASA Astrophysics Data System (ADS)

Singh, Shantanu; Harsha, A. P.

2016-10-01

There have been continuous on-going revisions in design of prosthesis in Total Hip Arthroplasty (THA) to improve the endurance of hip replacement. In the present work, Finite Element Analysis was performed on cemented THA with CoCrMo trapezoidal, CoCrMo circular, Ti6Al4V trapezoidal and Ti6Al4V circular stem. It was observed that cross section and material of femoral stem proved to be critical parameters for stress distribution in femoral components, distribution of interfacial stress and micro movements. In the first part of analysis, designs were investigated for micro movements and stress developed, for different stem materials. Later part of the analysis focused on investigations with respect to different stem cross sections. Femoral stem made of Titanium alloy (Ti6Al4V) resulted in larger debonding of stem at cement-stem interface and increased stress within the cement mantle in contrast to chromium alloy (CoCrMo) stem. Thus, CoCrMo proved to be a better choice for cemented THA. Comparison between CoCrMo femoral stem of trapezium and circular cross section showed that trapezoidal stem experiences lesser sliding and debonding at interfaces than circular cross section stem. Also, trapezium cross section generated lower peak stress in femoral stem and cortical femur. In present study, femur head with diameter of 36 mm was considered for the analysis in order to avoid dislocation of the stem. Also, metallic femur head was coupled with cross linked polyethylene liner as it experiences negligible wear compared to conventional polyethylene liner and unlike metallic liner it is non carcinogenic.

A practical divergence measure for survival distributions that can be estimated from Kaplan-Meier curves.

PubMed

Cox, Trevor F; Czanner, Gabriela

2016-06-30

This paper introduces a new simple divergence measure between two survival distributions. For two groups of patients, the divergence measure between their associated survival distributions is based on the integral of the absolute difference in probabilities that a patient from one group dies at time t and a patient from the other group survives beyond time t and vice versa. In the case of non-crossing hazard functions, the divergence measure is closely linked to the Harrell concordance index, C, the Mann-Whitney test statistic and the area under a receiver operating characteristic curve. The measure can be used in a dynamic way where the divergence between two survival distributions from time zero up to time t is calculated enabling real-time monitoring of treatment differences. The divergence can be found for theoretical survival distributions or can be estimated non-parametrically from survival data using Kaplan-Meier estimates of the survivor functions. The estimator of the divergence is shown to be generally unbiased and approximately normally distributed. For the case of proportional hazards, the constituent parts of the divergence measure can be used to assess the proportional hazards assumption. The use of the divergence measure is illustrated on the survival of pancreatic cancer patients. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Experimental evolution: Assortative mating and sexual selection, independent of local adaptation, lead to reproductive isolation in the nematode Caenorhabditis remanei.

PubMed

Castillo, Dean M; Burger, Melissa K; Lively, Curtis M; Delph, Lynda F

2015-12-01

Using experimental evolution, we investigated the contributions of ecological divergence, sexual selection, and genetic drift to the evolution of reproductive isolation in Caenorhabditis remanei. The nematodes were reared on two different environments for 100 generations. They were assayed for fitness on both environments after 30, 64, and 100 generations, and hybrid fitness were analyzed after 64 and 100 generations. Mating propensity within and between populations was also analyzed. The design allowed us to determine whether local adaptation was synchronous with pre- and postzygotic reproductive isolation. Prezygotic isolation evolved quickly but was unconnected with adaptation to the divergent environments. Instead, prezygotic isolation was driven by mate preferences favoring individuals from the same replicate population. A bottleneck treatment, meant to enhance the opportunity for genetic drift, had no effect on prezygotic isolation. Postzygotic isolation occurred in crosses where at least one population had a large fitness advantage in its "home" environment. Taken together, our results suggest that prezygotic isolation did not depend on drift or adaptation to divergent environments, but instead resulted from differences in sexual interactions within individual replicates. Furthermore, our results suggest that postzygotic isolation can occur between populations even when only one population has greater fitness in its home environment. © 2015 The Author(s). Evolution © 2015 The Society for the Study of Evolution.

SRB thermal curtain design support

NASA Technical Reports Server (NTRS)

Dixon, Carl A.; Lundblad, Wayne E.; Koenig, John R.

1992-01-01

Improvements in SRB Thermal Curtain were identified by thermal design featuring: selection of materials capable of thermal protection and service temperatures by tri-layering quartz, S2 glass, and Kevlar in thinner cross section; weaving in single piece (instead of 24 sections) to achieve improved strength; and weaving to reduce manufacturing cost with angle interlock construction.

A Cross-Sectional Analysis of Publication Types in Quality Improvement Journals.

PubMed

Wong, Christopher J; White, Andrew A; Merel, Susan E; Brock, Douglas M; Staiger, Thomas O

2016-07-01

Despite widespread engagement in quality improvement activities, little is known about the designs of studies currently published in quality improvement journals. This study's goal is to establish the prevalence of the types of research conducted in articles published in journals dedicated to quality improvement. A cross-sectional analysis was performed of 145 research articles published in 11 quality improvement journals in 2011. The majority of study designs were considered pre-experimental (95%), with a small percentage of quasi-experimental and experimental designs. Of the studies that reported the results of an intervention (n = 60), the most common research designs were pre-post studies (33%) and case studies (25%). There were few randomized controlled trials or quasi-experimental study designs (12% of intervention studies). These results suggest that there are opportunities for increased use of quasi-experimental study designs. © The Author(s) 2015.

Divergent selection on 63-day body weight in the rabbit: response on growth, carcass and muscle traits

PubMed Central

Larzul, Catherine; Gondret, Florence; Combes, Sylvie; de Rochambeau, Hubert

2005-01-01

The effects of selection for growth rate on weights and qualitative carcass and muscle traits were assessed by comparing two lines selected for live body weight at 63 days of age and a cryopreserved control population raised contemporaneously with generation 5 selected rabbits. The animals were divergently selected for five generations for either a high (H line) or a low (L line) body weight, based on their BLUP breeding value. Heritability (h2) was 0.22 for 63-d body weight (N = 4754). Growth performance and quantitative carcass traits in the C group were intermediate between the H and L lines (N = 390). Perirenal fat proportion (h2 = 0.64) and dressing out percentage (h2 = 0.55) ranked in the order L < H = C (from high to low). The weight and cross-sectional area of the Semitendinosus muscle, and the mean diameter of the constitutive myofibres were reduced in the L line only (N = 140). In the Longissimus muscle (N = 180), the ultimate pH (h2 = 0.16) and the maximum shear force reached in the Warner-Braztler test (h2 = 0.57) were slightly modified by selection. PMID:15588570

Balanced Rotating Spray Tank and Pipe Cleaning and Cleanliness Verification System

NASA Technical Reports Server (NTRS)

Caimi, Raoul E. B. (Inventor); Thaxton, Eric A. (Inventor)

1998-01-01

A system for cleaning and verifying the cleanliness of the interior surfaces of hollow items, such as small bottles, tanks, pipes and tubes, employs a rotating spray head for supplying a gas-liquid cleaning mixture to the item's surface at a supersonic velocity. The spray head incorporates a plurality of nozzles having diverging cross sections so that the incoming gas-liquid mixture is first converged within the spray head and then diverged through the nozzles, thereby accelerating the mixture to a supersonic velocity. In the preferred embodiment, three nozzles are employed; one forwardly facing nozzle at the end of the spray head and two oppositely facing angled nozzles exiting on opposite sides of the spray head which balance each other, and therefore impart no net side load on the spray head. A drive mechanism is provided to rotate the spray head and at the same time move the head back and forth within the item to be cleaned. The drive mechanism acts on a long metal tube to which the spray head is fixed, and thus no moving parts are exposed to the interior surfaces of the items to be cleaned, thereby reducing the risk of contamination.

Cross-Sectional and Longitudinal Risk Factors for Falls, Fear of Falling, and Falls Efficacy in a Cohort of Middle-Aged African Americans

ERIC Educational Resources Information Center

Anderson, Elena M.; Wolinsky, Fredric D.; Miller, J. Phillip; Wilson, Margaret-Mary G.; Malmstrom, Theodore K.; Miller, Douglas K.

2006-01-01

Purpose: The purpose of this study is to cross-sectionally and longitudinally identify risk factors for falls, fear of falling, and falls efficacy in late-middle-aged African Americans. Design and Methods: We performed in-home assessments on a probability sample of 998 African Americans and conducted two annual follow-up interviews. Multiple…

About creation of machines for rock destruction with formation of apertures of various cross-sections

NASA Astrophysics Data System (ADS)

Zhukov, I. A.; Dvornikov, L. T.; Nikitenko, S. M.

2016-04-01

The article presents the results of the experimental research of the high strength rock destruction by a bladeless tool. Rational circuit designs of disposing of indenters in the impact part of the drill bits and a diamond tool are justified. New constructive solutions of reinforcing bladeless drill bits, which allow drilling blast-holes of the various cross-section, are shown.

What Differentiates Adolescent Problematic Drinkers from Their Peers? Results from a Cross-Sectional Study in Northern Irish School Children

ERIC Educational Resources Information Center

McKay, Michael T.; Sumnall, Harry; Goudie, Andrew J.; Field, Matt; Cole, Jon C.

2011-01-01

Aim: To investigate whether or not a range of factors were associated with problematic drinking, as assessed using the Adolescent Alcohol Involvement Scale (AAIS) in a sample of 11-16-year olds in Northern Ireland. Methods: The study used a cross-sectional experimental design. Post-primary schools in the Eastern Health Board Area of Northern…

Design of transmission-type phase holograms for a compact radar-cross-section measurement range at 650 GHz.

PubMed

Noponen, Eero; Tamminen, Aleksi; Vaaja, Matti

2007-07-10

A design formalism is presented for transmission-type phase holograms for use in a submillimeter-wave compact radar-cross-section (RCS) measurement range. The design method is based on rigorous electromagnetic grating theory combined with conventional hologram synthesis. Hologram structures consisting of a curved groove pattern on a 320 mmx280 mm Teflon plate are designed to transform an incoming spherical wave at 650 GHz into an output wave generating a 100 mm diameter planar field region (quiet zone) at a distance of 1 m. The reconstructed quiet-zone field is evaluated by a numerical simulation method. The uniformity of the quiet-zone field is further improved by reoptimizing the goal field. Measurement results are given for a test hologram fabricated on Teflon.

The development of three-dimensional adjoint method for flow control with blowing in convergent-divergent nozzle flows

NASA Astrophysics Data System (ADS)

Sikarwar, Nidhi

The noise produced by the low bypass ratio turbofan engines used to power fighter aircraft is a problem for communities near military bases and for personnel working in close proximity to the aircraft. For example, carrier deck personnel are subject to noise exposure that can result in Noise-Induced Hearing Loss which in-turn results in over a billion dollars of disability payments by the Veterans Administration. Several methods have been proposed to reduce the jet noise at the source. These methods include microjet injection of air or water downstream of the jet exit, chevrons, and corrugated nozzle inserts. The last method involves the insertion of corrugated seals into the diverging section of a military-style convergent-divergent jet nozzle (to replace the existing seals). This has been shown to reduce both the broadband shock-associated noise as well as the mixing noise in the peak noise radiation direction. However, the original inserts were designed to be effective for a take-off condition where the jet is over-expanded. The nozzle performance would be expected to degrade at other conditions, such as in cruise at altitude. A new method has been proposed to achieve the same effects as corrugated seals, but using fluidic inserts. This involves injection of air, at relatively low pressures and total mass flow rates, into the diverging section of the nozzle. These fluidic inserts" deflect the flow in the same way as the mechanical inserts. The fluidic inserts represent an active control method, since the injectors can be modified or turned off depending on the jet operating conditions. Noise reductions in the peak noise direction of 5 to 6 dB have been achieved and broadband shock-associated noise is effectively suppressed. There are multiple parameters to be considered in the design of the fluidic inserts. This includes the number and location of the injectors and the pressures and mass flow rates to be used. These could be optimized on an ad hoc basis with multiple experiments or numerical simulations. Alternatively an inverse design method can be used. An adjoint optimization method can be used to achieve the optimum blowing rate. It is shown that the method works for both geometry optimization and active control of the flow in order to deflect the flow in desirable ways. An adjoint optimization method is described. It is used to determine the blowing distribution in the diverging section of a convergent-divergent nozzle that gives a desired pressure distribution in the nozzle. Both the direct and adjoint problems and their associated boundary conditions are developed. The adjoint method is used to determine the blowing distribution required to minimize the shock strength in the nozzle to achieve a known target pressure and to achieve close to an ideally expanded flow pressure. A multi-block structured solver is developed to calculate the flow solution and associated adjoint variables. Two and three-dimensional calculations are performed for internal and external of the nozzle domains. A two step MacCormack scheme based on predictor- corrector technique is was used for some calculations. The four and five stage Runge-Kutta schemes are also used to artificially march in time. A modified Runge-Kutta scheme is used to accelerate the convergence to a steady state. Second order artificial dissipation has been added to stabilize the calculations. The steepest decent method has been used for the optimization of the blowing velocity after the gradients of the cost function with respect to the blowing velocity are calculated using adjoint method. Several examples are given of the optimization of blowing using the adjoint method.

Cross-cultural adaptation and validation of the Patient-Rated Tennis Elbow Evaluation Questionnaire on lateral elbow tendinopathy for French-speaking patients.

PubMed

Kaux, Jean-François; Delvaux, François; Schaus, Jean; Demoulin, Christophe; Locquet, Médéa; Buckinx, Fanny; Beaudart, Charlotte; Dardenne, Nadia; Van Beveren, Julien; Croisier, Jean-Louis; Forthomme, Bénédicte; Bruyère, Olivier

Translation and validation of algo-functional questionnaire. The lateral elbow tendinopathy is a common injury in tennis players and physical workers. The Patient-Rated Tennis Elbow Evaluation (PRTEE) Questionnaire was specifically designed to measure pain and functional limitations in patients with lateral epicondylitis (tennis elbow). First developed in English, this questionnaire has since been translated into several languages. The aims of the study were to translate and cross-culturally adapt the PRTEE questionnaire into French and to evaluate the reliability and validity of this translated version of the questionnaire (PRTEE-F). The PRTEE was translated and cross-culturally adapted into French according to international guidelines. To assess the reliability and validity of the PRTEE-F, 115 participants were asked twice to fill in the PRTEE-F, and once the Disabilities of Arm, Shoulder and Hand Questionnaire (DASH) and the Short Form Health Survey (SF-36). Internal consistency (using Cronbach's alpha), test-retest reliability (using intraclass correlation coefficient (ICC), standard error of measurement and minimal detectable change), and convergent and divergent validity (using the Spearman's correlation coefficients respectively with the DASH and with some subscales of the SF-36) were assessed. The PRTEE was translated into French without any problems. PRTEE-F showed a good test-retest reliability for the overall score (ICC 0.86) and for each item (ICC 0.8-0.96) and a high internal consistency (Cronbach's alpha = 0.98). The correlation analyses revealed high correlation coefficients between PRTEE-F and DASH (convergent validity) and, as expected, a low or moderate correlation with the divergent subscales of the SF-36 (discriminant validity). There was no floor or ceiling effect. The PRTEE questionnaire was successfully cross-culturally adapted into French. The PRTEE-F is reliable and valid for evaluating French-speaking patients with lateral elbow tendinopathy. Copyright © 2016 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Test technology on divergence angle of laser range finder based on CCD imaging fusion

NASA Astrophysics Data System (ADS)

Shi, Sheng-bing; Chen, Zhen-xing; Lv, Yao

2016-09-01

Laser range finder has been equipped with all kinds of weapons, such as tank, ship, plane and so on, is important component of fire control system. Divergence angle is important performance and incarnation of horizontal resolving power for laser range finder, is necessary appraised test item in appraisal test. In this paper, based on high accuracy test on divergence angle of laser range finder, divergence angle test system is designed based on CCD imaging, divergence angle of laser range finder is acquired through fusion technology for different attenuation imaging, problem that CCD characteristic influences divergence angle test is solved.

Laser-hole boring into overdense plasmas measured with soft X-Ray laser probing

PubMed

Takahashi; Kodama; Tanaka; Hashimoto; Kato; Mima; Weber; Barbee; Da Silva LB

2000-03-13

A laser self-focused channel formation into overdense plasmas was observed using a soft x-ray laser probe system with a grid image refractometry (GIR) technique. 1.053 &mgr;m laser light with a 100 ps pulse duration was focused onto a preformed plasma at an intensity of 2x10(17) W/cm (2). Cross sections of the channel were obtained which show a 30 &mgr;m diameter in overdense plasmas. The channel width in the overdense region was kept narrow as a result of self-focusing. Conically diverging density ridges were also observed along the channel, indicating a Mach cone created by a shock wave due to the supersonic propagation of the channel front.

Collision group and renormalization of the Boltzmann collision integral.

PubMed

Saveliev, V L; Nanbu, K

2002-05-01

On the basis of a recently discovered collision group [V. L. Saveliev, in Rarefied Gas Dynamics: 22nd International Symposium, edited by T. J. Bartel and M. Gallis, AIP Conf. Proc. No. 585 (AIP, Melville, NY, 2001), p. 101], the Boltzmann collision integral is exactly rewritten in two parts. The first part describes the scattering of particles with small angles. In this part the infinity due to the infinite cross sections is extracted from the Boltzmann collision integral. Moreover, the Boltzmann collision integral is represented as a divergence of the flow in velocity space. Owing to this, the role of collisions in the kinetic equation can be interpreted in terms of the nonlocal friction force that depends on the distribution function.

Collision group and renormalization of the Boltzmann collision integral

NASA Astrophysics Data System (ADS)

Saveliev, V. L.; Nanbu, K.

2002-05-01

On the basis of a recently discovered collision group [V. L. Saveliev, in Rarefied Gas Dynamics: 22nd International Symposium, edited by T. J. Bartel and M. Gallis, AIP Conf. Proc. No. 585 (AIP, Melville, NY, 2001), p. 101], the Boltzmann collision integral is exactly rewritten in two parts. The first part describes the scattering of particles with small angles. In this part the infinity due to the infinite cross sections is extracted from the Boltzmann collision integral. Moreover, the Boltzmann collision integral is represented as a divergence of the flow in velocity space. Owing to this, the role of collisions in the kinetic equation can be interpreted in terms of the nonlocal friction force that depends on the distribution function.

Epidemiological, virological and clinical characteristics of HBV infection in 223 HIV co-infected patients: a French multi-centre collaborative study.

PubMed

Thibault, Vincent; Gaudy-Graffin, Catherine; Colson, Philippe; Gozlan, Joël; Schnepf, Nathalie; Trimoulet, Pascale; Pallier, Coralie; Saune, Karine; Branger, Michel; Coste, Marianne; Thoraval, Francoise Roudot

2013-03-15

Chronic hepatitis B (CHB) is a clinical concern in human immunodeficiency virus (HIV)-infected individuals due to substantial prevalence, difficulties to treat, and severe liver disease outcome. A large nationwide cross-sectional multicentre analysis of HIV-HBV co-infected patients was designed to describe and identify parameters associated with virological and clinical outcome of CHB in HIV-infected individuals with detectable HBV viremia. A multicenter collaborative cross-sectional study was launched in 19 French University hospitals distributed through the country. From January to December 2007, HBV load, genotype, clinical and epidemiological characteristics of 223 HBV-HIV co-infected patients with an HBV replication over 1000 IU/mL were investigated. Patients were mostly male (82%, mean age 42 years). Genotype distribution (A 52%; E 23.3%; D 16.1%) was linked to risk factors, geographic origin, and co-infection with other hepatitis viruses. This genotypic pattern highlights divergent contamination event timelines by HIV and HBV viruses. Most patients (74.7%) under antiretroviral treatment were receiving a drug with anti-HBV activity, including 47% receiving TDF. Genotypic lamivudine-resistance detected in 26% of the patients was linked to duration of lamivudine exposure, age, CD4 count and HIV load. Resistance to adefovir (rtA181T/V) was detected in 2.7% of patients. Advanced liver lesions were observed in 54% of cases and were associated with an older age and lower CD4 counts but not with viral load or genotype. Immune escape HBsAg variants were seldom detected. Despite the detection of advanced liver lesions in most patients, few were not receiving anti-HBV drugs and for those treated with the most potent anti-HBV drugs, persistent replication suggested non-optimal adherence. Heterogeneity in HBV strains reflects epidemiological differences that may impact liver disease progression. These findings are strong arguments to further optimize clinical management and to promote vaccination in HIV-infected patients.

An Excess Broadband Noise Observed with Overexpanded Jets

NASA Technical Reports Server (NTRS)

Zaman, K.B.M.Q.; Bridges, James E.; Brown, C.A.

2009-01-01

Results of an experiment on the characteristics of an excess noise occurring with convergent-divergent (C-D) nozzles in the overexpanded regime are presented in this paper. Data are obtained with five C-D nozzles and a convergent nozzle, all having the same exit diameter. The results clearly establish that the C-D nozzles are noisier in the low Mach number range of the overexpanded regime. This is evidenced from the directivity patterns as well as overall radiated sound power calculations. The excess noise is broadband in nature and is found to be more pronounced with nozzles having a larger half-angle of the divergent section. It appears to occur when a shock resides within the divergent section and results from random unsteady motion of the shock.

Comparative genomics and repetitive sequence divergence in the species of diploid Nicotiana section Alatae.

PubMed

Lim, K Yoong; Kovarik, Ales; Matyasek, Roman; Chase, Mark W; Knapp, Sandra; McCarthy, Elizabeth; Clarkson, James J; Leitch, Andrew R

2006-12-01

Combining phylogenetic reconstructions of species relationships with comparative genomic approaches is a powerful way to decipher evolutionary events associated with genome divergence. Here, we reconstruct the history of karyotype and tandem repeat evolution in species of diploid Nicotiana section Alatae. By analysis of plastid DNA, we resolved two clades with high bootstrap support, one containing N. alata, N. langsdorffii, N. forgetiana and N. bonariensis (called the n = 9 group) and another containing N. plumbaginifolia and N. longiflora (called the n = 10 group). Despite little plastid DNA sequence divergence, we observed, via fluorescent in situ hybridization, substantial chromosomal repatterning, including altered chromosome numbers, structure and distribution of repeats. Effort was focussed on 35S and 5S nuclear ribosomal DNA (rDNA) and the HRS60 satellite family of tandem repeats comprising the elements HRS60, NP3R and NP4R. We compared divergence of these repeats in diploids and polyploids of Nicotiana. There are dramatic shifts in the distribution of the satellite repeats and complete replacement of intergenic spacers (IGSs) of 35S rDNA associated with divergence of the species in section Alatae. We suggest that sequence homogenization has replaced HRS60 family repeats at sub-telomeric regions, but that this process may not occur, or occurs more slowly, when the repeats are found at intercalary locations. Sequence homogenization acts more rapidly (at least two orders of magnitude) on 35S rDNA than 5S rDNA and sub-telomeric satellite sequences. This rapid rate of divergence is analogous to that found in polyploid species, and is therefore, in plants, not only associated with polyploidy.

Extensive CD4 and CD8 T-cell cross-reactivity between alphaherpesviruses1

PubMed Central

Dong, Lichun; Russell, Ronnie M.; Barlow, Russell S.; Haas, Juergen G.; Ramchandani, Meena S.; Johnston, Christine; Buus, Soren; Redwood, Alec J.; White, Katie D.; Mallal, Simon A.; Phillips, Elizabeth J.; Posavad, Christine M.; Wald, Anna; Koelle, David M.

2015-01-01

The alphaherpesvirinae subfamily includes HSV types 1 and 2 and the sequence-divergent pathogen varicella zoster virus (VZV). T cells, controlled by TCR and HLA molecules that tolerate limited epitope amino acid variation, might cross-react between these microbes. We show that memory PBMC expansion with either HSV or VZV enriches for CD4 T cell lines that recognize the other agent at the whole virus, protein, and peptide levels, consistent with bi-directional cross-reactivity. HSV-specific CD4 T cells recovered from HSV seronegative persons can be partially explained by such VZV cross-reactivity. HSV-1-reactive CD8 T cells also cross-react with VZV-infected cells, full-length VZV proteins, and VZV peptides, and kill VZV-infected dermal fibroblasts. Mono- and cross-reactive CD8 T cells use distinct TCRB CDR3 sequences. Cross-reactivity to VZV is reconstituted by cloning and expressing TCRA/TCRB receptors from T-cells that are initially isolated using HSV reagents. Overall, we define 13 novel CD4 and CD8 HSV-VZV cross-reactive epitopes and strongly imply additional cross-reactive peptide sets. Viral proteins can harbor both CD4 and CD8 HSV/VZV cross-reactive epitopes. Quantitative estimates of HSV/VZV cross-reactivity for both CD4 and CD8 T cells vary from 10-50%. Based on these findings, we hypothesize host herpesvirus immune history may influence the pathogenesis and clinical outcome of subsequent infections or vaccinations for related pathogens, and that cross-reactive epitopes and TCRs may be useful for multi-alphaherpesvirus vaccine design and adoptive cellular therapy. PMID:26810224

Stiffness Characteristics of Composite Rotor Blades With Elastic Couplings

NASA Technical Reports Server (NTRS)

Piatak, David J.; Nixon, Mark W.; Kosmatka, John B.

1997-01-01

Recent studies on rotor aeroelastic response and stability have shown the beneficial effects of incorporating elastic couplings in composite rotor blades. However, none of these studies have clearly identified elastic coupling limits and the effects of elastic couplings on classical beam stiffnesses of representative rotor blades. Knowledge of these limits and effects would greatly enhance future aeroelastic studies involving composite rotor blades. The present study addresses these voids and provides a preliminary design database for investigators who may wish to study the effects of elastic couplings on representative blade designs. The results of the present study should provide a basis for estimating the potential benefits associated with incorporating elastic couplings without the need for first designing a blade cross section and then performing a cross-section analysis to obtain the required beam section properties as is customary in the usual one-dimensional beam-type approach.

Population Aging at Cross-Roads: Diverging Secular Trends in Average Cognitive Functioning and Physical Health in the Older Population of Germany

PubMed Central

Steiber, Nadia

2015-01-01

This paper uses individual-level data from the German Socio-Economic Panel to model trends in population health in terms of cognition, physical fitness, and mental health between 2006 and 2012. The focus is on the population aged 50–90. We use a repeated population-based cross-sectional design. As outcome measures, we use SF-12 measures of physical and mental health and the Symbol-Digit Test (SDT) that captures cognitive processing speed. In line with previous research we find a highly significant Flynn effect on cognition; i.e., SDT scores are higher among those who were tested more recently (at the same age). This result holds for men and women, all age groups, and across all levels of education. While we observe a secular improvement in terms of cognitive functioning, at the same time, average physical and mental health has declined. The decline in average physical health is shown to be stronger for men than for women and found to be strongest for low-educated, young-old men aged 50–64: the decline over the 6-year interval in average physical health is estimated to amount to about 0.37 SD, whereas average fluid cognition improved by about 0.29 SD. This pattern of results at the population-level (trends in average population health) stands in interesting contrast to the positive association of physical health and cognitive functioning at the individual-level. The findings underscore the multi-dimensionality of health and the aging process. PMID:26323093

Experimental investigation of a 10-percent-thick helicopter rotor airfoil section designed with a viscous transonic analysis code

NASA Technical Reports Server (NTRS)

Noonan, K. W.

1981-01-01

An investigation was conducted in the Langley 6- by 28-Inch Transonic Tunnel to determine the two dimensional aerodynamic characteristics of a 10-percent-thick helicopter rotor airfoil at Mach numbers from 0.33 to 0.87 and respective Reynolds numbers from 4.9 x 10 to the 6th to 9.8 x 10 to the 6th. This airfoil, designated the RC-10(N)-1, was also investigated at Reynolds numbers from 3.0 x 10 to the 6th to 7.3 x 10 to the 6th at respective Mach numbers of 0.33 to 0.83 for comparison wit the SC 1095 (with tab) airfoil. The RC-10(N)-1 airfoil was designed by the use of a viscous transonic analysis code. The results of the investigation indicate that the RC-10(N)-1 airfoil met all the design goals. At a Reynolds number of about 9.4 x 10 to the 6th the drag divergence Mach number at zero normal-force coefficient was 0.815 with a corresponding pitching-moment coefficient of zero. The drag divergence Mach number at a normal-force coefficient of 0.9 and a Reynolds number of about 8.0 x 10 to the 6th was 0.61. The drag divergence Mach number of this new airfoil was higher than that of the SC 1095 airfoil at normal-force coefficients above 0.3. Measurements in the same wind tunnel at comparable Reynolds numbers indicated that the maximum normal-force coefficient of the RC-10(N)-1 airfoil was higher than that of the NACA 0012 airfoil for Mach numbers above about 0.35 and was about the same as that of the SC 1095 airfoil for Mach numbers up to 0.5.

Parametric Study of Fire Performance of Concrete Filled Hollow Steel Section Columns with Circular and Square Cross-Section

NASA Astrophysics Data System (ADS)

Nurfaidhi Rizalman, Ahmad; Tahir, Ng Seong Yap Mahmood Md; Mohammad, Shahrin

2018-03-01

Concrete filled hollow steel section column have been widely accepted by structural engineers and designers for high rise construction due to the benefits of combining steel and concrete. The advantages of concrete filled hollow steel section column include higher strength, ductility, energy absorption capacity, and good structural fire resistance. In this paper, comparison on the fire performance between circular and square concrete filled hollow steel section column is established. A three-dimensional finite element package, ABAQUS, was used to develop the numerical model to study the temperature development, critical temperature, and fire resistance time of the selected composite columns. Based on the analysis and comparison of typical parameters, the effect of equal cross-sectional size for both steel and concrete, concrete types, and thickness of external protection on temperature distribution and structural fire behaviour of the columns are discussed. The result showed that concrete filled hollow steel section column with circular cross-section generally has higher fire resistance than the square section.

Experimental investigation on the thermal performance of Si micro-heat pipe with different cross-sections

NASA Astrophysics Data System (ADS)

Hamidnia, Mohammad; Luo, Yi; Wang, Xiaodong; Li, Congming

2017-10-01

Increasing component densities of the integrated circuit (IC) and packaging levels has led to thermal management problems. Si substrates with embedded micro-heat pipes (MHPs) couple good thermal characteristics and cost savings associated with IC batch processing. The thermal performance of MHP is intimately related to the cross-sectional geometry. Different cross-sections are designed in order to enhance the backflow of working fluid. In this experimental study, three different Si MHPs with same hydraulic diameter and various cross-sections are fabricated by micro-fabrication methods and tested under different conditions of fluid charge ratios. The results show that the trapezoidal MHP associated with rectangular artery which is charged with 40% of vapor chamber’s volume has the best thermal performance. This silicon-based MHP is a passive approach for thermal management, which could widen applications in the commercial electronics industry and LED lightings.

Reducing Uncertainties in Neutron Induced Fission Cross Sections via a Time Projection Chamber

NASA Astrophysics Data System (ADS)

Magee, Joshua; Niffte Collaboration

2016-09-01

Neutron induced fission cross sections of actinides are of great interest in nuclear energy and stockpile stewardship. Traditionally, measurements of these cross sections have been made with fission chambers, which provide limited information on the actual fragments, and ultimately result in uncertainties on the order of several percent. The Neutron Induced Fission Fragment Tracking Experiment collaboration (NIFFTE) designed and built a fission Time Project Chamber (fission TPC), which provides additional information on these processes, through 3-dimensional tracking, improved particle identification, and in-situ profiles of target and beam non-uniformities. Ultimately, this should provide sub-percent measurements of (n,f) cross-sections. During the 2015 run cycle, measurements of several actinides were performed at the Los Alamos Neutron Science Center (LANSCE) Weapons Neutron Research (WNR) facility. An overview of the fission TPC will be given, as well as the current progress towards a sub-percent measurement of the 239Pu/235U (n,f) cross-section ratio. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

A New Measurement of Neutron Induced Fission Cross Sections

NASA Astrophysics Data System (ADS)

Magee, Joshua; Niffte Collaboration

2017-09-01

Neutron induced fission cross sections of actinides are of great interest in nuclear energy and stockpile stewardship. Traditionally, measurements of these cross sections have been made with fission chambers, which provide limited information on the actual fragments, and ultimately result in uncertainties on the order of several percent. The Neutron Induced Fission ragment Tracking Experiment (NIFFTE) collaboration designed and built a fission Time Projection Chamber (fissionTPC), which provides additional information on these processes, through 3-dimensional tracking, improved particle identification, and in-situ profiles of target and beam non-uniformities. Ultimately, this should provide sub-percent measurements of (n,f) cross-sections. During the 2016 run cycle, measurements of the 238U(n,f)/235U(n,f) cross section shape was performed at the Los Alamos Neutron Science Center (LANSCE) Weapons Neutron Research (WNR) facility. An overview of the fission TPC will be given, as well as these recently reported results. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Measurement of the 241Am neutron capture cross section at the n_TOF facility at CERN

NASA Astrophysics Data System (ADS)

Mendoza, E.; Cano-Ott, D.; Altstadt, S.; Andriamonje, S.; Andrzejewski, J.; Audouin, L.; Balibrea, J.; Bécares, V.; Barbagallo, M.; Bečvář, F.; Belloni, F.; Berthier, B.; Berthoumieux, E.; Billowes, J.; Boccone, V.; Bosnar, D.; Brugger, M.; Calviño, F.; Calviani, M.; Carrapiço, C.; Cerutti, F.; Chiaveri, E.; Chin, M.; Colonna, N.; Cortés, G.; Cortés-Giraldo, M. A.; Diakaki, M.; Dillmann, I.; Domingo-Pardo, C.; Durán, I.; Dzysiuk, N.; Eleftheriadis, C.; Fernández-Ordóñez, M.; Ferrari, A.; Fraval, K.; Furman, V.; Gómez-Hornillos, M. B.; Ganesan, S.; García, A. R.; Giubrone, G.; Gonçalves, I. F.; González, E.; Goverdovski, A.; Gramegna, F.; Griesmayer, E.; Guerrero, C.; Gunsing, F.; Gurusamy, P.; Heftrich, T.; Heinitz, S.; Hernández-Prieto, A.; Heyse, J.; Jenkins, D. G.; Jericha, E.; Käppeler, F.; Kadi, Y.; Karadimos, D.; Katabuchi, T.; Ketlerov, V.; Khryachkov, V.; Koehler, P.; Kokkoris, M.; Kroll, J.; Krtička, M.; Lampoudis, C.; Langer, C.; Leal-Cidoncha, E.; Lederer, C.; Leeb, H.; Leong, L. S.; Lerendegui-Marco, J.; Licata, M.; Losito, R.; Manousos, A.; Marganiec, J.; Martínez, T.; Massimi, C.; Mastinu, P.; Mastromarco, M.; Mengoni, A.; Milazzo, P. M.; Mingrone, F.; Mirea, M.; Mondelaers, W.; Paradela, C.; Pavlik, A.; Perkowski, J.; Plompen, A. J. M.; Praena, J.; Quesada, J. M.; Rauscher, T.; Reifarth, R.; Riego-Perez, A.; Robles, M.; Roman, F.; Rubbia, C.; Ryan, J. A.; Sabaté-Gilarte, M.; Sarmento, R.; Saxena, A.; Schillebeeckx, P.; Schmidt, S.; Schumann, D.; Sedyshev, P.; Tagliente, G.; Tain, J. L.; Tarifeño-Saldivia, A.; Tarrío, D.; Tassan-Got, L.; Tsinganis, A.; Valenta, S.; Vannini, G.; Variale, V.; Vaz, P.; Ventura, A.; Vermeulen, M. J.; Versaci, R.; Vlachoudis, V.; Vlastou, R.; Wallner, A.; Ware, T.; Weigand, M.; Weiss, C.; Wright, T.; Žugec, P.

2017-09-01

New neutron cross section measurements of minor actinides have been performed recently in order to reduce the uncertainties in the evaluated data, which is important for the design of advanced nuclear reactors and, in particular, for determining their performance in the transmutation of nuclear waste. We have measured the 241Am(n,γ) cross section at the n_TOF facility between 0.2 eV and 10 keV with a BaF2 Total Absorption Calorimeter, and the analysis of the measurement has been recently concluded. Our results are in reasonable agreement below 20 eV with the ones published by C. Lampoudis et al. in 2013, who reported a 22% larger capture cross section up to 110 eV compared to experimental and evaluated data published before. Our results also indicate that the 241Am(n,γ) cross section is underestimated in the present evaluated libraries between 20 eV and 2 keV by 25%, on average, and up to 35% for certain evaluations and energy ranges.

Neutron capture reactions at DANCE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bredeweg, T. A.

2008-05-12

The Detector for Advanced Neutron Capture Experiments (DANCE) is a 4{pi} BaF{sub 2} array consisting of 160 active detector elements. The primary purpose of the array is to perform neutron capture cross section measurements on small (> or approx.100 {mu}g) and/or radioactive (< or approx. 100 mCi) species. The measurements made possible with this array will be useful in answering outstanding questions in the areas of national security, threat reduction, nuclear astrophysics, advanced reactor design and accelerator transmutation of waste. Since the commissioning of DANCE we have performed neutron capture cross section measurements on a wide array of medium tomore » heavy mass nuclides. Measurements to date include neutron capture cross sections on {sup 241,243}Am, neutron capture and neutron-induced fission cross sections and capture-to-fission ratio ({alpha} = {sigma}{sub {gamma}}/{sigma}{sub f}) for {sup 235}U using a new fission-tagging detector as well as neutron capture cross sections for several astrophysics branch-point nuclei. Results from several of these measurements will be presented along with a discussion of additional physics information that can be extracted from the DANCE data.« less

Multigenerational outbreeding effects in Chinook salmon (Oncorhynchus tshawytscha).

PubMed

Lehnert, Sarah J; Love, Oliver P; Pitcher, Trevor E; Higgs, Dennis M; Heath, Daniel D

2014-08-01

Outbreeding, mating between genetically divergent individuals, may result in negative fitness consequences for offspring via outbreeding depression. Outbreeding effects are of notable concern in salmonid research as outbreeding can have major implications for salmon aquaculture and conservation management. We therefore quantified outbreeding effects in two generations (F1 hybrids and F2 backcrossed hybrids) of Chinook salmon (Oncorhynchus tshawytscha) derived from captively-reared purebred lines that had been selectively bred for differential performance based on disease resistance and growth rate. Parental lines were crossed in 2009 to create purebred and reciprocal hybrid crosses (n = 53 families), and in 2010 parental and hybrid crosses were crossed to create purebred and backcrossed hybrid crosses (n = 66 families). Although we found significant genetic divergence between the parental lines (FST = 0.130), reciprocal F1 hybrids showed no evidence of outbreeding depression (hybrid breakdown) or favorable heterosis for weight, length, condition or survival. The F2 backcrossed hybrids showed no outbreeding depression for a suite of fitness related traits measured from egg to sexually mature adult life stages. Our study contributes to the current knowledge of outbreeding effects in salmonids and supports the need for more research to better comprehend the mechanisms driving outbreeding depression.

Topology of an intracellular transduction chain (phototropism of Phycomyces): 1. Joint review of functional, temporal, and spatial aspects.

PubMed

Wenzler, D; Reinhardt, M; Fukshansky, L

2001-08-21

Two light-induced growth reactions in a unicellular cylindrical sporangiophore of Phycomyces blakesleeanus-vertical growth acceleration under symmetrical irradiation (photomecism) and directional growth under unilateral irradiation (phototropism)-share common input light perception as well as common output growth mechanism but have strongly divergent dynamics and other distinctive features. This divergence culminates in the phototropic paradoxes the main of which states that photomecism shows total adaptation, while phototropism does not adapt. The basis for this contradiction is that the phototropic transduction chain, unlike that of photomecism, faces a spatially non-uniform stimulus and processes a series of spatial patterns (light and absorption profiles, adaptation profile, etc.). The only way to resolve the paradoxes and correlate features of both responses within a single transduction chain is to assume non-local signal transduction, e.g. a cross-talk between different azimuthal locations within the cylindrical cell. On the other hand, to establish the presence of an appropriate cross-talk is equivalent of gaining insight into the topology of the transduction chain. This series of two papers contains a review reconsidering the entire field from this viewpoint (Paper 1) and a mathematical model of pattern transduction which unifies features of phototropism and resolves the paradoxes (Paper 2). At the same time, this is the first "proof of concept" for the "activity/pooling (a/p) networks"-a specific mathematical apparatus designed to analyse systemic properties and control in metabolic pathways. Copyright 2001 Academic Press.

Multistep Cylindrical Structure Analysis at Normal Incidence Based on Water-Substrate Broadband Metamaterial Absorbers

NASA Astrophysics Data System (ADS)

Fang, Chonghua

2018-01-01

A new multistep cylindrical structure based on water-substrate broadband metamaterial absorbers is designed to reduce the traditional radar cross-section (RCS) of a rod-shaped object. The proposed configuration consists of two distinct parts. One of these components is formed by a four-step cylindrical metal structure, whereas the other one is formed by a new water-substrate broadband metamaterial absorber. The designed structure can significantly reduce the radar cross section more than 10 dB from 4.58 to 18.42 GHz which is the 86.5 % bandwidth of from C-band to 20 GHz. The results of measurement show reasonably good accordance with the simulated ones, which verifies the ability and effect of the proposed design.

Annual Review of Asian American Psychology, 2014

PubMed Central

Kim, Su Yeong; Shen, Yishan; Hou, Yang; Tilton, Kelsey E.; Juang, Linda; Wang, Yijie

2015-01-01

This 2014 review of Asian American psychology is the sixth review in the series. It includes 316 articles that met the inclusion criteria established by the past five annual reviews. Featured articles were derived from three sources: 137 were generated via the search term “Asian American” in PyscINFO, 111 were generated via a search for specific Asian American ethnic groups, and 32 were generated via author searches of articles that met the inclusion criteria. The top primary topic was health and health-related behaviors, the most frequently employed study design was cross-sectional, and the most studied Asian American ethnic group was Chinese. This year’s review includes information on the target population of the primary topic, the age range and developmental period of participants, and whether the study design was cross-sectional or longitudinal. It also identifies top authors and journals contributing to the 2014 annual review. These new features reveal that the most common target population of the primary topic was youths; studies most commonly included emerging adults ages 18–25; cross-sectional study design was employed more often than longitudinal design; the top contributor to the 2014 review was Stephen Chen, who authored the highest number of papers included; and the Asian American Journal of Psychology generated the highest number of publications for this review. PMID:26925199

Decreased body mass index in the preclinical stage of autosomal dominant Alzheimer's disease.

PubMed

Müller, Stephan; Preische, Oliver; Sohrabi, Hamid R; Gräber, Susanne; Jucker, Mathias; Dietzsch, Janko; Ringman, John M; Martins, Ralph N; McDade, Eric; Schofield, Peter R; Ghetti, Bernardino; Rossor, Martin; Graff-Radford, Neill R; Levin, Johannes; Galasko, Douglas; Quaid, Kimberly A; Salloway, Stephen; Xiong, Chengjie; Benzinger, Tammie; Buckles, Virginia; Masters, Colin L; Sperling, Reisa; Bateman, Randall J; Morris, John C; Laske, Christoph

2017-04-27

The relationship between body-mass index (BMI) and Alzheimer´s disease (AD) has been extensively investigated. However, BMI alterations in preclinical individuals with autosomal dominant AD (ADAD) have not yet been investigated. We analyzed cross-sectional data from 230 asymptomatic members of families with ADAD participating in the Dominantly Inherited Alzheimer Network (DIAN) study including 120 preclinical mutation carriers (MCs) and 110 asymptomatic non-carriers (NCs). Differences in BMI and their relation with cerebral amyloid load and episodic memory as a function of estimated years to symptom onset (EYO) were analyzed. Preclinical MCs showed significantly lower BMIs compared to NCs, starting 11.2 years before expected symptom onset. However, the BMI curves begun to diverge already at 17.8 years before expected symptom onset. Lower BMI in preclinical MCs was significantly associated with less years before estimated symptom onset, higher global Aβ brain burden, and with lower delayed total recall scores in the logical memory test. The study provides cross-sectional evidence that weight loss starts one to two decades before expected symptom onset of ADAD. Our findings point toward a link between the pathophysiology of ADAD and disturbance of weight control mechanisms. Longitudinal follow-up studies are warranted to investigate BMI changes over time.

An Investigation of the Drag and Pressure Recovery of a Submerged Inlet and a Nose Inlet in the Transonic Flight Range with Free-fall Models

NASA Technical Reports Server (NTRS)

Selna, James; Schlaff, Bernard A

1951-01-01

The drag and pressure recovery of an NACA submerged-inlet model and an NACA series I nose-inlet model were investigated in the transonic flight range. The tests were conducted over a mass-flow-ratio range of 0.4 to 0.8 and a Mach number range of about 0.8 to 1.10 employing large-scale recoverable free-fall models. The results indicate that the Mach number of drag divergence of the inlet models was about the same as that of a basic model without inlets. The external drag coefficients of the nose-inlet model were less than those of the submerged-inlet model throughout the test range. The difference in drag coefficient based on the maximum cross-sectional area of the models was about 0.02 at supersonic speeds and about 0.015 at subsonic speeds. For a hypothetical airplane with a ratio of maximum fuselage cross-sectional area to wing area of 0.06, the difference in airplane drag coefficient would be relatively small, about 0.0012 at supersonic speeds and about 0.0009 at subsonic speeds. Additional drag comparisons between the two inlet models are made considering inlet incremental and additive drag.

Electronically cloaked nanoparticles

NASA Astrophysics Data System (ADS)

Shen, Wenqing

The concept of electronic cloaking is to design objects invisible to conduction electrons. The approach of electronic cloaking has been recently suggested to design invisible nanoparticle dopants with electronic scattering cross section smaller than 1% of the physical cross section (pi a2), and therefore to enhance the carrier mobility of bulk materials. The proposed nanoparticles have core-shell structures. The dopants are incorporated inside the core, while the shell layer serves both as a spacer to separate the charge carriers from their parent atoms and as a cloaking shell to minimize the scattering cross section of the electrons from the ionized nanoparticles. Thermoelectric materials are usually highly doped to have enough carrier density. Using invisible dopants could achieve larger thermoelectric power factors by enhancing the electronic mobility. Core-shell nanoparticles show an advantage over one-layer nanoparticles, which are proposed in three-dimensional modulation doping. However designing such nanoparticles is not easy as there are too many parameters to be considered. This thesis first shows an approach to design hollow nanoparticles by applying constrains on variables. In the second part, a simple mapping approach is introduced where one can identify possible core-shell particles by comparing the dimensionless parameters of chosen materials with provided maps. In both parts of this work, several designs with realistic materials were made and proven to achieve electronic cloaking. Improvement in the thermoelectric power factor compared to the traditional impurity doping method was demonstrated in several cases.

Sensitivity Analysis of Nuclide Importance to One-Group Neutron Cross Sections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sekimoto, Hiroshi; Nemoto, Atsushi; Yoshimura, Yoshikane

The importance of nuclides is useful when investigating nuclide characteristics in a given neutron spectrum. However, it is derived using one-group microscopic cross sections, which may contain large errors or uncertainties. The sensitivity coefficient shows the effect of these errors or uncertainties on the importance.The equations for calculating sensitivity coefficients of importance to one-group nuclear constants are derived using the perturbation method. Numerical values are also evaluated for some important cases for fast and thermal reactor systems.Many characteristics of the sensitivity coefficients are derived from the derived equations and numerical results. The matrix of sensitivity coefficients seems diagonally dominant. However,more » it is not always satisfied in a detailed structure. The detailed structure of the matrix and the characteristics of coefficients are given.By using the obtained sensitivity coefficients, some demonstration calculations have been performed. The effects of error and uncertainty of nuclear data and of the change of one-group cross-section input caused by fuel design changes through the neutron spectrum are investigated. These calculations show that the sensitivity coefficient is useful when evaluating error or uncertainty of nuclide importance caused by the cross-section data error or uncertainty and when checking effectiveness of fuel cell or core design change for improving neutron economy.« less

Expanding probe repertoire and improving reproducibility in human genomic hybridization

PubMed Central

Dorman, Stephanie N.; Shirley, Ben C.; Knoll, Joan H. M.; Rogan, Peter K.

2013-01-01

Diagnostic DNA hybridization relies on probes composed of single copy (sc) genomic sequences. Sc sequences in probe design ensure high specificity and avoid cross-hybridization to other regions of the genome, which could lead to ambiguous results that are difficult to interpret. We examine how the distribution and composition of repetitive sequences in the genome affects sc probe performance. A divide and conquer algorithm was implemented to design sc probes. With this approach, sc probes can include divergent repetitive elements, which hybridize to unique genomic targets under higher stringency experimental conditions. Genome-wide custom probe sets were created for fluorescent in situ hybridization (FISH) and microarray genomic hybridization. The scFISH probes were developed for detection of copy number changes within small tumour suppressor genes and oncogenes. The microarrays demonstrated increased reproducibility by eliminating cross-hybridization to repetitive sequences adjacent to probe targets. The genome-wide microarrays exhibited lower median coefficients of variation (17.8%) for two HapMap family trios. The coefficients of variations of commercial probes within 300 nt of a repetitive element were 48.3% higher than the nearest custom probe. Furthermore, the custom microarray called a chromosome 15q11.2q13 deletion more consistently. This method for sc probe design increases probe coverage for FISH and lowers variability in genomic microarrays. PMID:23376933

Draw-and-Write Technique Elicits Children's Perceptions of Health in the USA and Guatemala

ERIC Educational Resources Information Center

Renslow, Jillian; Maupin, Jonathan

2018-01-01

Objective: Using the draw-and-write methodology, this study examined cross-cultural similarities and differences in children's perceptions of health. Design: Cross-sectional design. Setting: One public elementary school in the USA and in Guatemala. Method: The total sample included 161 children 9-10 years of age, 80 in the USA and 81 in Guatemala.…

Comparison of characteristics and downstream uniformity of linear-field and cross-field atmospheric pressure plasma jet array in He

NASA Astrophysics Data System (ADS)

Zhang, Bo; Fang, Zhi; Liu, Feng; Zhou, Renwu; Zhou, Ruoyu

2018-06-01

Using an atmospheric pressure plasma jet array is an effective way for expanding the treatment area of a single jet, and generating arrays with well downstream uniformity is of great interest for its applications. In this paper, a plasma jet array in helium is generated in a linear-field jet array with a ring-ring electrode structure excited by alternating current. The characteristics and downstream uniformity of the array and their dependence on the applied voltage and gas flow rate are investigated through optical, electrical, and Schlieren diagnostics. The results are compared with those of our reported work of a cross-field jet array with a needle-ring electrode structure. The results show that the linear-field jet array can generate relatively large-scale plasma with better uniformity and longer plumes than the cross-field case. The divergences observed in gas channels and the plasma plume trajectories are much less than those of the cross-field one. The deflection angle of lateral plumes is less than 6°, which is independent of the gas flow rate and applied voltage. The maximum downstream plumes of 23 mm can be obtained at 7 kV peak applied voltage and 4 l/min gas flow rate. The better uniformity of linear-field jet arrays is due to the effective suppression of hydrodynamic and electrical interactions among the jets in the arrays with a more uniform electric field distribution. The hydrodynamic interaction induced by the gas heating in the linear-field jet array is less than that of the cross-field one. The more uniform electric field distribution in the linear-field jet arrays can reduce the divergence of the propagation trajectories of the plasma plumes. It will generate less residual charge between the adjacent discharges and thus can reduce the accumulation effect of Coulomb force between the plasma plumes. The reported results can help design controllable and scalable plasma jet arrays with well uniformity for material surface and biomedical treatments.

Twenty years' research on peer victimization and psychosocial maladjustment: a meta-analytic review of cross-sectional studies.

PubMed

Hawker, D S; Boulton, M J

2000-05-01

Cross-sectional quantitative designs are often used to investigate whether peer victimization is positively related to psychosocial maladjustment. This paper presents a meta-analytic review of cross-sectional studies, published between 1978 and 1997, of the association of peer victimization with psychosocial maladjustment. Mean effect sizes were calculated for the association between peer victimization and each form of maladjustment (depression, loneliness, generalized and social anxiety, and global and social self-worth) assessed. The results suggested that victimization is most strongly related to depression, and least strongly related to anxiety. There was no evidence that victimization is more strongly related to social than to psychological forms of maladjustment. Effect sizes were stronger when the same informants were used to assess both victimization and maladjustment than when different informants were used. There were some design limitations to the studies reviewed, but all together their results provide a strong background for more complex research into the course and treatment of victims' distress.

An overview of DANCE: a 4II BaF[2] detector for neutron capture measurements at LANSCE.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ullmann, J. L.

2004-01-01

The Detector for Advanced Neutron Capture experiments (DANCE) is a 162-element, 4{pi} BaF{sub 2} array designed to make neutron capture cross-section measurements on rare or radioactive targets with masses as little as 1 mg. Accurate capture cross sections are needed in many research areas, including stellar nucleosynthesis, advanced nuclear fuel cycles, waste transmutation, and other applied programs. These cross sections are difficult to calculate accurately and must be measured. Up to now, except for a few long-lived nuclides there are essentially no differential capture measurements on radioactive nuclei. The DANCE array is located at the Lujan Neutron Scattering Center atmore » LANSCE, which is a continuous-spectrum neutron source with useable energies from below thermal to about 100 keV. Data acquisition is done with 320 fast waveform digitizers. The design and initial performance results, including background minimization, will be discussed.« less

Field Quality and Fabrication Analysis of HQ02 Reconstructed Nb3Sn Coil Cross Sections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holik, Eddie Frank; Ambrosio, Giorgio; Carbonara, Andrea

2017-01-23

The US LHC Accelerator Research Program (LARP) quadrupole HQ02 was designed and fully tested as part of the low-beta quad development for Hi-Lumi LHC. HQ02’s design is well documented with full fabrication accounting along with full field analysis at low and high current. With this history, HQ02 is an excellent test bed for developing a methodology for measuring turn locations from magnet cross sections and comparing with CAD models and measured field. All 4 coils of HQ02 were cut in identical locations along the magnetic length corresponding to magnetic field measurement and coil metrology. A real-time camera and coordinate measuringmore » equipment was used to plot turn corners. Measurements include systematic and random displacements of winding blocks and individual turns along the magnetic length. The range of cable shifts and the field harmonic range along the length are in agreement, although correlating turn locations and measured harmonics in each cross section is challenging.« less

Bridging the Gap Between Understanding and Doing in Structural Geology - Coring the Subsurface with Scratch-Art

NASA Astrophysics Data System (ADS)

Bilsley, N. A.; Cook, H. M.

2016-12-01

Although most geology students feel the joy of interpreting geologic cross sections, few experience the challenges career geologists face in order to create these visual representations. Without a hefty budget and a drill rig, students generally miss out on the challenge of extrapolating subsurficial features from limited datasets, and jump to narrating geologic time through beautifully pre-drawn cross sections. Although this method allows students to practice relative dating techniques, they miss the practical step of learning how we have come to understand what the subsurface looks like in the first place. This activity was designed to close that gap, while giving students the opportunity to engage in peer learning by strategizing in groups, critiquing each other's work, and evaluating their own work. Broken into groups, students are instructed to create a geologic cross section that must include specific structural features. The cross sections are traded with another group, who reviews and provides feedback on the drawing before returning it back to the original group. The feedback is reviewed and incorporated, before the cross sections are colored and covered with black coated, clear scratch-art paper. The hidden cross sections are traded with a new group, who must decide where and how deep to scratch, or "core", on their cross section. Utilizing the data obtained from the cores, the students interpret and draw a new cross section. Finally, the scratch-art paper is removed, and the original cross section revealed. The differences between the original and interpreted subsurface as well as evaluation of sampling methods (e.g. location and depth of cores) are discussed within the groups and with the class. This activity bridges the gap between developing the intuition needed to create cross sections with realistic geoscientific techniques and utilizing cross sections to understand geologic time. In addition, not only does the activity require few supplies and minimal time of the instructor, but its peer-based learning approach stimulates creativity, allows students to effectively generate and communicate constructive feedback, and encourages students to evaluate and critique their methods and assumptions.

50 CFR 81.11 - Divergent opinions over project merits.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Divergent opinions over project merits. 81.11 Section 81.11 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED) FINANCIAL ASSISTANCE-WILDLIFE SPORT FISH RESTORATION PROGRAM CONSERVATION OF...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Casperson, R. J.; Burke, J. T.; Hughes, R. O.

Directly measuring (n,2n) cross sections on short-lived actinides presents a number of experimental challenges. The surrogate reaction technique is an experimental method for measuring cross sections on short-­lived isotopes, and it provides a unique solution for measuring (n,2n) cross sections. This technique involves measuring a charged-­particle reaction cross section, where the reaction populates the same compound nucleus as the reaction of interest. To perform these surrogate (n,2n) cross section measurements, a silicon telescope array has been placed along a beam line at the Texas A&M University Cyclotron Institute, which is surrounded by a large tank of gadolinium-doped liquid scintillator, whichmore » acts as a neutron detector. The combination of the charge-particle and neutron-detector arrays is referred to as NeutronSTARS. In the analysis procedure for calculating the (n,2n) cross section, the neutron detection efficiency and time structure plays an important role. Due to the lack of availability of isotropic, mono-energetic neutron sources, modeling is an important component in establishing this efficiency and time structure. This report describes the NeutronSTARS array, which was designed and commissioned during this project. It also describes the surrogate reaction technique, specifically referencing a 235U(n,2n) commissioning measurement that was fielded during the past year. Advanced multiplicity analysis techniques have been developed for this work, which should allow for efficient analysis of 241Pu(n,2n) and 239Pu(n,2n) cross section measurements« less

Neuroanatomical phenotypes in mental illness: identifying convergent and divergent cortical phenotypes across autism, ADHD and schizophrenia.

PubMed

Park, Min Tae M; Raznahan, Armin; Shaw, Philip; Gogtay, Nitin; Lerch, Jason P; Chakravarty, M Mallar

2018-05-01

There is evidence suggesting neuropsychiatric disorders share genomic, cognitive and clinical features. Here, we ask if autism-spectrum disorders (ASD), attention-deficit/hyperactivity disorder (ADHD) and schizophrenia share neuroanatomical variations. First, we used measures of cortical anatomy to estimate spatial overlap of neuroanatomical variation using univariate methods. Next, we developed a novel methodology to determine whether cortical deficits specifically target or are "enriched" within functional resting-state networks. We found cortical anomalies were preferentially enriched across functional networks rather than clustering spatially. Specifically, cortical thickness showed significant enrichment between patients with ASD and those with ADHD in the default mode network, between patients with ASD and those with schizophrenia in the frontoparietal and limbic networks, and between patients with ADHD and those with schizophrenia in the ventral attention network. Networks enriched in cortical thickness anomalies were also strongly represented in functional MRI results (Neurosynth; r = 0.64, p = 0.032). We did not account for variable symptom dimensions and severity in patient populations, and our cross-sectional design prevented longitudinal analyses of developmental trajectories. These findings suggest that common deficits across neuropsychiatric disorders cannot simply be characterized as arising out of local changes in cortical grey matter, but rather as entities of both local and systemic alterations targeting brain networks.

Learning styles of registered nurses enrolled in an online nursing program.

PubMed

Smith, Anita

2010-01-01

Technological advances assist in the proliferation of online nursing programs which meet the needs of the working nurse. Understanding online learning styles permits universities to adequately address the educational needs of the professional nurse returning for an advanced degree. The purpose of this study was to describe the learning styles of registered nurses (RNs) enrolled in an online master's nursing program or RN-bachelor of science in nursing (BSN) program. A descriptive, cross-sectional design was used. Kolb's learning style inventory (Version 3.1) was completed by 217 RNs enrolled in online courses at a Southeastern university. Descriptive statistical procedures were used for analysis. Thirty-one percent of the nurses were accommodators, 20% were assimilators, 19% were convergers, and 20% were divergers. Accommodators desire hand-on experiences, carrying out plans and tasks and using an intuitive trial-and-error approach to problem solving. The learning styles of the RNs were similar to the BSN students in traditional classroom settings. Despite their learning style, nurses felt that the online program met their needs. Implementing the technological innovations in nursing education requires the understanding of the hands-on learning of the RN so that the development of the online courses will satisfactorily meet the needs of the nurses who have chosen an online program. Copyright 2010 Elsevier Inc. All rights reserved.

Neuroanatomical phenotypes in mental illness: identifying convergent and divergent cortical phenotypes across autism, ADHD and schizophrenia.

PubMed

Park, Min Tae M; Raznahan, Armin; Shaw, Philip; Gogtay, Nitin; Lerch, Jason P; Chakravarty, M Mallar

2018-02-05

There is evidence suggesting neuropsychiatric disorders share genomic, cognitive and clinical features. Here, we ask if autism-spectrum disorders (ASD), attention-deficit/hyperactivity disorder (ADHD) and schizophrenia share neuroanatomical variations. First, we used measures of cortical anatomy to estimate spatial overlap of neuroanatomical variation using univariate methods. Next, we developed a novel methodology to determine whether cortical deficits specifically target or are "enriched" within functional resting-state networks. We found cortical anomalies were preferentially enriched across functional networks rather than clustering spatially. Specifically, cortical thickness showed significant enrichment between patients with ASD and those with ADHD in the default mode network, between patients with ASD and those with schizophrenia in the frontoparietal and limbic networks, and between patients with ADHD and those with schizophrenia in the ventral attention network. Networks enriched in cortical thickness anomalies were also strongly represented in functional MRI results (Neurosynth; r = 0.64, p = 0.032). We did not account for variable symptom dimensions and severity in patient populations, and our cross-sectional design prevented longitudinal analyses of developmental trajectories. These findings suggest that common deficits across neuropsychiatric disorders cannot simply be characterized as arising out of local changes in cortical grey matter, but rather as entities of both local and systemic alterations targeting brain networks.

Preliminary structural design of composite main rotor blades for minimum weight

NASA Technical Reports Server (NTRS)

Nixon, Mark W.

1987-01-01

A methodology is developed to perform minimum weight structural design for composite or metallic main rotor blades subject to aerodynamic performance, material strength, autorotation, and frequency constraints. The constraints and load cases are developed such that the final preliminary rotor design will satisfy U.S. Army military specifications, as well as take advantage of the versatility of composite materials. A minimum weight design is first developed subject to satisfying the aerodynamic performance, strength, and autorotation constraints for all static load cases. The minimum weight design is then dynamically tuned to avoid resonant frequencies occurring at the design rotor speed. With this methodology, three rotor blade designs were developed based on the geometry of the UH-60A Black Hawk titanium-spar rotor blade. The first design is of a single titanium-spar cross section, which is compared with the UH-60A Black Hawk rotor blade. The second and third designs use single and multiple graphite/epoxy-spar cross sections. These are compared with the titanium-spar design to demonstrate weight savings from use of this design methodology in conjunction with advanced composite materials.

Effect of cross sectional geometry on PDMS micro peristaltic pump performance: comparison of SU-8 replica molding vs. micro injection molding.

PubMed

Graf, Neil J; Bowser, Michael T

2013-10-07

Two different fabrication methods were employed to fabricate micropumps with different cross-sectional channel geometries. The first was to fabricate rectangular cross-sectional microchannel geometries using the well known fabrication method of replica molding (REM). The second, and far less utilized fabrication technique, was to create microchannel molds using an in-house fabricated handheld micro injection molding apparatus. The injection mold apparatus was designed for use with elastomeric room temperature vulcanization (RTV) polymers, as opposed to most other injection molding machines, which are designed for use with thermoplastic polymers. The injection mold's bottom plate was used as a microchannel molding template. The molding template was created by threading a small-diameter wire (150 μm or less) through the injection mold's bottom plate, with subsequent adhesion and smoothing of a thin piece of aluminum foil over the wire-raised injection mold template. When molded against, the template produced a rounded/Gaussian-shaped PDMS microchannel. The design of the injection mold will be presented, along with a direct comparison for micropump performance metrics such as flow rate, valving characteristics, and maximum backpressures attainable for each of the respective micropump channel geometries.

Assessment of the neutron cross section database for mercury for the ORNL spallation source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leal, L.C.; Spencer, R.R.; Ingersoll, D.T.

1996-06-01

Neutron source generation based on a high energy particle accelerator has been considered as an alternative to the canceled Advanced Neutron Source project at Oak Ridge National Laboratory. The proposed technique consists of a spallation neutron source in which neutrons are produced via the interaction of high-energy charged particles in a heavy metal target. Preliminary studies indicate that liquid mercury bombarded with GeV protons provides an excellent neutron source. Accordingly, a survey has been made of the available neutron cross-section data. Since it is expected that spectral modifiers, specifically moderators, will also be incorporated into the source design, the surveymore » included thermal energy, resonance region, and high energy data. It was found that data of individual isotopes were almost non-existent and that the only evaluation found for the natural element had regions of missing data or discrepant data. Therefore, it appears that to achieve the desired degree of accuracy in the spallation source design it is necessary to re-evaluate the mercury database including making new measurements. During the presentation the currently available data will be presented and experiments proposed which can lead to design quality cross sections.« less

Monitoring corrosion of rebar embedded in mortar using guided ultrasonic waves

NASA Astrophysics Data System (ADS)

Ervin, Benjamin Lee

This thesis investigates the use of guided mechanical waves for monitoring uniform and localized corrosion in steel reinforcing bars embedded in concrete. The main forms of structural deterioration from uniform corrosion in reinforced concrete are the destruction of the bond between steel and concrete, the loss of steel cross-sectional area, and the loss of concrete cross-sectional area from cracking and spalling. Localized corrosion, or pitting, leads to severe loss of steel cross-sectional area, creating a high risk of bar tensile failure and unintended transfer of loads to the surrounding concrete. Reinforcing bars were used to guide the waves, rather than bulk concrete, allowing for longer inspection distances due to lower material absorption, scattering, and divergence. Guided mechanical waves in low frequency ranges (50-200 kHz) and higher frequency ranges (2-8 MHz) were monitored in reinforced mortar specimens undergoing accelerated uniform corrosion. The frequency ranges chosen contain wave modes with varying amounts of interaction, i.e. displacement profile, at the material interface. Lower frequency modes were shown to be sensitive to the accumulation of corrosion product and the level of bond between the surrounding mortar and rebar. This allows for the onset of corrosion and bond deterioration to be monitored. Higher frequency modes were shown to be sensitive to changes in the bar profile surface, allowing for the loss of cross-sectional area to be monitored. Guided mechanical waves in the higher frequency range were also used to monitor reinforced mortar specimens undergoing accelerated localized corrosion. The high frequency modes were sensitive to the localized attack. Also promising was the unique frequency spectrum response for both uniform and localized corrosion, allowing the two corrosion types to be differentiated from through-transmission evaluation. The isolated effects of the reinforcing ribs, simulated debonding, simulated pitting, water surrounding, and mortar surrounding were also investigated using guided mechanical waves. Results are presented and discussed within the framework of a corrosion process degradation model and service life. A thorough review and discussion of the corrosion process, modeling the propagation of corrosion, nondestructive methods for monitoring corrosion in reinforced concrete, and guided mechanical waves have also been presented.

Confinement effect of cylindrical-separatrix-type magnetic field on the plume of magnetic focusing type Hall thruster

NASA Astrophysics Data System (ADS)

Yu, Daren; Meng, Tianhang; Ning, Zhongxi; Liu, Hui

2017-04-01

A magnetic focusing type Hall thruster was designed with a cylindrical magnetic seperatrix. During the process of a hollow cathode crossing the separatrix, the variance of plume parameter distribution was monitored. Results show that the ion flux on the large spatial angle is significantly lower when the hollow cathode is located in the inner magnetic field. This convergence effect is preserved even in a distant area. A mechanism was proposed for plume divergence from the perspective of cathode-to-plume potential difference, through which the confinement effect of cylindrical-separatrix-type magnetic field on thruster plume was confirmed and proposed as a means of plume protection for plasma propulsion devices.

Full Navier-Stokes analysis of a two-dimensional mixer/ejector nozzle for noise suppression

NASA Technical Reports Server (NTRS)

Debonis, James R.

1992-01-01

A three-dimensional full Navier-Stokes (FNS) analysis was performed on a mixer/ejector nozzle designed to reduce the jet noise created at takeoff by a future supersonic transport. The PARC3D computational fluid dynamics (CFD) code was used to study the flow field of the nozzle. The grid that was used in the analysis consisted of approximately 900,000 node points contained in eight grid blocks. Two nozzle configurations were studied: a constant area mixing section and a diverging mixing section. Data are presented for predictions of pressure, velocity, and total temperature distributions and for evaluations of internal performance and mixing effectiveness. The analysis provided good insight into the behavior of the flow.

Who Gets Designated a Terrorist and Why?

ERIC Educational Resources Information Center

Beck, Colin J.; Miner, Emily

2013-01-01

This study examines formal terrorism designations by governments through the lens of organization studies research on categorization processes. It is argued that designations hinge on markers from the organizational profile of a militant group. Using cross-sectional data on militant organizations and designations by the United States, the United…

Low-energy electron scattering from water molecules: A study of angular distributions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gianturco, F.A.; Scialla, S.

1987-12-01

We report quantal calculations of elastic differential and momentum transfercross sections for the scattering of electrons by H/sub 2/O at low and intermediatecollision energies, i.e., from 2 to 20 eV. The fixed-nuclei approximation (FNA) was employed and a single-center expanded (SCE) wave function was used to represent the molecular target. The well-known divergence in the forward direction was corrected via Born closure formulas (see the text) and a parameter-free model, previously tested for methane targets, was used to describe exchange and polarization effects. The present results can be used to adequately describe angular distributions even at very small angles andmore » can be extended beyond the largest angles that have been experimentally measured. The behavior of momentum-transfer cross sections as a function of energy, and the comparison of our results with other static-exchange (SE) calculations, which use an entirely different approach, are presented and discussed.« less

Structural Insight into How Bacteria Prevent Interference between Multiple Divergent Type IV Secretion Systems

PubMed Central

Phan, Isabelle Q. H.; Scheib, Holger; Subramanian, Sandhya; Edwards, Thomas E.; Lehman, Stephanie S.; Piitulainen, Hanna; Sayeedur Rahman, M.; Rennoll-Bankert, Kristen E.; Staker, Bart L.; Taira, Suvi; Stacy, Robin; Myler, Peter J.; Azad, Abdu F.

2015-01-01

ABSTRACT Prokaryotes use type IV secretion systems (T4SSs) to translocate substrates (e.g., nucleoprotein, DNA, and protein) and/or elaborate surface structures (i.e., pili or adhesins). Bacterial genomes may encode multiple T4SSs, e.g., there are three functionally divergent T4SSs in some Bartonella species (vir, vbh, and trw). In a unique case, most rickettsial species encode a T4SS (rvh) enriched with gene duplication. Within single genomes, the evolutionary and functional implications of cross-system interchangeability of analogous T4SS protein components remains poorly understood. To lend insight into cross-system interchangeability, we analyzed the VirB8 family of T4SS channel proteins. Crystal structures of three VirB8 and two TrwG Bartonella proteins revealed highly conserved C-terminal periplasmic domain folds and dimerization interfaces, despite tremendous sequence divergence. This implies remarkable structural constraints for VirB8 components in the assembly of a functional T4SS. VirB8/TrwG heterodimers, determined via bacterial two-hybrid assays and molecular modeling, indicate that differential expression of trw and vir systems is the likely barrier to VirB8-TrwG interchangeability. We also determined the crystal structure of Rickettsia typhi RvhB8-II and modeled its coexpressed divergent paralog RvhB8-I. Remarkably, while RvhB8-I dimerizes and is structurally similar to other VirB8 proteins, the RvhB8-II dimer interface deviates substantially from other VirB8 structures, potentially preventing RvhB8-I/RvhB8-II heterodimerization. For the rvh T4SS, the evolution of divergent VirB8 paralogs implies a functional diversification that is unknown in other T4SSs. Collectively, our data identify two different constraints (spatiotemporal for Bartonella trw and vir T4SSs and structural for rvh T4SSs) that mediate the functionality of multiple divergent T4SSs within a single bacterium. PMID:26646013

Comparison of safety effect estimates obtained from empirical Bayes before-after study, propensity scores-potential outcomes framework, and regression model with cross-sectional data.

PubMed

Wood, Jonathan S; Donnell, Eric T; Porter, Richard J

2015-02-01

A variety of different study designs and analysis methods have been used to evaluate the performance of traffic safety countermeasures. The most common study designs and methods include observational before-after studies using the empirical Bayes method and cross-sectional studies using regression models. The propensity scores-potential outcomes framework has recently been proposed as an alternative traffic safety countermeasure evaluation method to address the challenges associated with selection biases that can be part of cross-sectional studies. Crash modification factors derived from the application of all three methods have not yet been compared. This paper compares the results of retrospective, observational evaluations of a traffic safety countermeasure using both before-after and cross-sectional study designs. The paper describes the strengths and limitations of each method, focusing primarily on how each addresses site selection bias, which is a common issue in observational safety studies. The Safety Edge paving technique, which seeks to mitigate crashes related to roadway departure events, is the countermeasure used in the present study to compare the alternative evaluation methods. The results indicated that all three methods yielded results that were consistent with each other and with previous research. The empirical Bayes results had the smallest standard errors. It is concluded that the propensity scores with potential outcomes framework is a viable alternative analysis method to the empirical Bayes before-after study. It should be considered whenever a before-after study is not possible or practical. Copyright © 2014 Elsevier Ltd. All rights reserved.

Bloom DNA Helicase Facilitates Homologous Recombination between Diverged Homologous Sequences*

PubMed Central

Kikuchi, Koji; Abdel-Aziz, H. Ismail; Taniguchi, Yoshihito; Yamazoe, Mitsuyoshi; Takeda, Shunichi; Hirota, Kouji

2009-01-01

Bloom syndrome caused by inactivation of the Bloom DNA helicase (Blm) is characterized by increases in the level of sister chromatid exchange, homologous recombination (HR) associated with cross-over. It is therefore believed that Blm works as an anti-recombinase. Meanwhile, in Drosophila, DmBlm is required specifically to promote the synthesis-dependent strand anneal (SDSA), a type of HR not associating with cross-over. However, conservation of Blm function in SDSA through higher eukaryotes has been a matter of debate. Here, we demonstrate the function of Blm in SDSA type HR in chicken DT40 B lymphocyte line, where Ig gene conversion diversifies the immunoglobulin V gene through intragenic HR between diverged homologous segments. This reaction is initiated by the activation-induced cytidine deaminase enzyme-mediated uracil formation at the V gene, which in turn converts into abasic site, presumably leading to a single strand gap. Ig gene conversion frequency was drastically reduced in BLM−/− cells. In addition, BLM−/− cells used limited donor segments harboring higher identity compared with other segments in Ig gene conversion event, suggesting that Blm can promote HR between diverged sequences. To further understand the role of Blm in HR between diverged homologous sequences, we measured the frequency of gene targeting induced by an I-SceI-endonuclease-mediated double-strand break. BLM−/− cells showed a severer defect in the gene targeting frequency as the number of heterologous sequences increased at the double-strand break site. Conversely, the overexpression of Blm, even an ATPase-defective mutant, strongly stimulated gene targeting. In summary, Blm promotes HR between diverged sequences through a novel ATPase-independent mechanism. PMID:19661064

The Escherichia coli cAMP receptor protein bound at a single target can activate transcription initiation at divergent promoters: a systematic study that exploits new promoter probe plasmids.

PubMed Central

El-Robh, Mohamed Samir; Busby, Stephen J W

2002-01-01

We report the first detailed quantitative study of divergent promoters dependent on the Escherichia coli cAMP receptor protein (CRP), a factor known to activate transcription initiation at target promoters by making direct interactions with the RNA polymerase holoenzyme. In this work, we show that CRP bound at a single target site is able to activate transcription at two divergently organized promoters. Experiments using promoter probe plasmids, designed to study divergent promoters in vivo and in vitro, show that the divergent promoters function independently. Further in vitro experiments show that two holo RNA polymerase molecules cannot be accommodated simultaneously at the divergent promoters. PMID:12350222

Ground state energies from converging and diverging power series expansions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lisowski, C.; Norris, S.; Pelphrey, R.

2016-10-15

It is often assumed that bound states of quantum mechanical systems are intrinsically non-perturbative in nature and therefore any power series expansion methods should be inapplicable to predict the energies for attractive potentials. However, if the spatial domain of the Schrödinger Hamiltonian for attractive one-dimensional potentials is confined to a finite length L, the usual Rayleigh–Schrödinger perturbation theory can converge rapidly and is perfectly accurate in the weak-binding region where the ground state’s spatial extension is comparable to L. Once the binding strength is so strong that the ground state’s extension is less than L, the power expansion becomes divergent,more » consistent with the expectation that bound states are non-perturbative. However, we propose a new truncated Borel-like summation technique that can recover the bound state energy from the diverging sum. We also show that perturbation theory becomes divergent in the vicinity of an avoided-level crossing. Here the same numerical summation technique can be applied to reproduce the energies from the diverging perturbative sums.« less

Roles of divergent and rotational winds in the kinetic energy balance during intense convective activity

NASA Technical Reports Server (NTRS)

Fuelberg, H. E.; Browning, P. A.

1983-01-01

Contributions of divergent and rotational wind components to the synoptic-scale kinetic energy balance are described using rawinsonde data at 3 and 6 h intervals from NASA's fourth Atmospheric Variability experiment. Two intense thunderstorm complexes occurred during the period. Energy budgets are described for the entire computational region and for limited volumes that enclosed storm-induced, upper level wind maxima located poleward of convection. Although small in magnitude, the divergent wind component played an important role in the cross-contour generation and horizontal flux divergence of kinetic energy. The importance of V(D) appears directly related to the presence and intensity of convection. Although K(D) usually comprised less than 10 percent of the total kinetic energy content, generation of kinetic energy by V(D) was a major factor in the creation of upper-level wind maxima to the north of the storm complexes. Omission of the divergent wind apparently would lead to serious misrepresentations of the energy balance. A random error analysis is presented to assess confidence limits in the various energy parameters.

Temperature-induced sol-gel transition and microgel formation in α-actinin cross-linked actin networks: A rheological study

NASA Astrophysics Data System (ADS)

Tempel, M.; Isenberg, G.; Sackmann, E.

1996-08-01

We have studied the sol-gel transition, the viscoelastic and the structural properties of networks constituted of semiflexible actin filaments cross-linked by α-actinin. Cross-linking was regulated in a reversible way by varying the temperature through the association-dissociation equilibrium of the actin-α-actinin system. Viscoelastic parameters [shear storage modulus G'(ω), phase shift tan(Φ)(ω), creep compliance J(t)] were measured as a function of temperature and actin-to-cross-linker ratio by a magnetically driven rotating disc rheometer. G'(ω) and tan(Φ)(ω) were studied at a frequency ω corresponding to the elastic plateau regime of the G'(ω) versus ω spectrum of the purely entangled solution. The microstructure of the networks was viewed by negative staining electron microscopy (EM). The phase shift tan(Φ) (or equivalently the viscosity η) diverges and reaches a maximum when approaching the apparent gel point from lower and higher temperatures, and the maximum defines the gel point (temperature Tg). The elastic plateau modulus G'N diverges at temperatures beyond this gel point TTg. The cross-linking transition (corresponding to a sol-gel transition at zero frequency) is interpreted in terms of a percolation model and the divergence of G'N at TTg), (2) that microscopic segregation takes place at T<=Tg leading to local formation of clusters (a state termed microgel), and (3) that at low actin-α-actinin ratios (rAα<=10) and low temperatures (T<=10 °C) macroscopic segregation into bundles of cross-linked actin filaments and a diluted solution of actin filaments is observed. The three regimes of network structure are represented by an equivalent phase diagram.

DOE Office of Scientific and Technical Information (OSTI.GOV)

MIchael A. Pope

Six early cores of the MASURCA R-Z program were modeled using ERANOS 2.1. These cores were designed such that their neutron spectra would be similar to that of an oxide-fueled sodium-cooled fast reactor, some containing enriched uranium and others containing depleted uranium and plutonium. Effects of modeling assumptions and solution methods both in ECCO lattice calculations and in BISTRO Sn flux solutions were evaluated using JEFF-3.1 cross-section libraries. Reactivity effects of differences between JEFF-3.1 and ENDF/B-VI.8 were also quantified using perturbation theory analysis. The most important nuclide with respect to reactivity differences between cross-section libraries was 23Na, primarily a resultmore » of differences in the angular dependence of elastic scattering which is more forward-peaked in ENDF/B-VI.8 than in JEFF-3.1. Differences in 23Na inelastic scattering cross-sections between libraries also generated significant differences in reactivity, more due to the differences in magnitude of the cross-sections than the angular dependence. The nuclide 238U was also found to be important with regard to reactivity differences between the two libraries mostly due to a large effect of inelastic scattering differences and two smaller effects of elastic scattering and fission cross-sections. In the cores which contained plutonium, 239Pu fission cross-section differences contributed significantly to the reactivity differences between libraries.« less

Traumatic Dental Injuries in the primary dentition: a 15-year bibliometric analysis of Dental Traumatology.

PubMed

Kramer, Paulo Floriani; Onetto, Juan; Flores, Marie Therese; Borges, Tássia Silvana; Feldens, Carlos Alberto

2016-10-01

To explore the profile of articles on traumatic dental injuries (TDI) in the primary dentition published in Dental Traumatology in the last 15 years using bibliometric analysis. Three researchers read all titles and abstracts of articles published in Dental Traumatology between 2000 and 2014 (excluding editorials and letters) and selected all articles on TDI in the primary dentition. The articles were categorized according to year of publication, country in which the study was conducted, study design, and topics addressed. Divergences were resolved by consensus between the researchers. Among a total of 1257 articles published, 98 were initially excluded. Among the remaining 1159 articles, 152 (13.1%) focused on TDI in the primary dentition. The articles were conducted in 29 countries, with Brazil (38.8%) and Turkey (11.8%) accounting for the largest numbers. Cross-sectional studies (36.2%) and case report/case series (33.6%) were the most frequent study designs. Only two systematic reviews were published. The most commonly addressed topics were frequency/etiology/associated factors (36.8%), treatment (30.9%), and prognosis (19.7%). Among the articles addressing treatment, two-thirds were case reports or case series. The effects of TDI in primary teeth on their permanent successors were addressed in 20.4% of the articles (31/152). The number of articles on TDI in the primary dentition has increased, but remains low. The evaluation of study designs and topics addressed identified gaps that could contribute to the development of new studies on TDI in the primary dentition, especially cohort studies that evaluate risk factors, prognosis, and treatment. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

First comparative insight into the architecture of COI mitochondrial minicircle molecules of dicyemids reveals marked inter-species variation.

PubMed

Catalano, Sarah R; Whittington, Ian D; Donnellan, Stephen C; Bertozzi, Terry; Gillanders, Bronwyn M

2015-07-01

Dicyemids, poorly known parasites of benthic cephalopods, are one of the few phyla in which mitochondrial (mt) genome architecture departs from the typical ~16 kb circular metazoan genome. In addition to a putative circular genome, a series of mt minicircles that each comprises the mt encoded units (I-III) of the cytochrome c oxidase complex have been reported. Whether the structure of the mt minicircles is a consistent feature among dicyemid species is unknown. Here we analyse the complete cytochrome c oxidase subunit I (COI) minicircle molecule, containing the COI gene and an associated non-coding region (NCR), for ten dicyemid species, allowing for first time comparisons between species of minicircle architecture, NCR function and inferences of minicircle replication. Divergence in COI nucleotide sequences between dicyemid species was high (average net divergence = 31.6%) while within species diversity was lower (average net divergence = 0.2%). The NCR and putative 5' section of the COI gene were highly divergent between dicyemid species (average net nucleotide divergence of putative 5' COI section = 61.1%). No tRNA genes were found in the NCR, although palindrome sequences with the potential to form stem-loop structures were identified in some species, which may play a role in transcription or other biological processes.

Super free fall for a container composed of diverging flat plates

NASA Astrophysics Data System (ADS)

Medina, A.; Torres, A.; Peralta, S.; Weidman, P. D.

2010-11-01

We have analyzed experimentally and theoretically the characteristics of the upper free surface of a liquid column released from rest in a vertical container whose cross-section opens slowly in the downward direction. In distinction with the work of Villermaux and Pomeau (2010) for a conical container, we consider a container composed of slightly inclined flat surfaces. At small times for which viscous effects can be neglected, the free surface moves downward with an acceleration larger than gravity. The existence of a nipple centered on the upper free surface with amplitude an increasing function of time is observed. A one-dimensional model of the initial acceleration for flat, slightly expanding walls reproduces the observed super free fall experiments fairly well. Details of the nipple development will be presented.

Effect of screens in wide-angle diffusers

NASA Technical Reports Server (NTRS)

Schubauer, G B; Spangenberg, W G

1949-01-01

An experimental investigation at low airspeeds was made of the filling effect observed when a screen or similar resistance is placed across a diffuser. The filling effect is found to be real in that screens can prevent separation or restore separated flow in diffusers even of extreme divergence and to depend principally on screen location and pressure-drop coefficient of the screen. Results are given for three different diffusers of circular cross section with a variety of screen arrangements. Effects of single screens and multiple screens are shown. The mechanics of the filling effect is explained, and possible efficiencies are discussed. Results of arrangements of multiple screens in wide-angle diffusers are given to show a possible application to damping screens as used in wind tunnels to reduce turbulence. (author)

Fusion materials high energy-neutron studies. A status report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doran, D.G.; Guinan, M.W.

1980-01-01

The objectives of this paper are (1) to provide background information on the US Magnetic Fusion Reactor Materials Program, (2) to provide a framework for evaluating nuclear data needs associated with high energy neutron irradiations, and (3) to show the current status of relevant high energy neutron studies. Since the last symposium, the greatest strides in cross section development have been taken in those areas providing FMIT design data, e.g., source description, shielding, and activation. In addition, many dosimetry cross sections have been tentatively extrapolated to 40 MeV and integral testing begun. Extensive total helium measurements have been made inmore » a variety of neutron spectra. Additional calculations are needed to assist in determining energy dependent cross sections.« less

Aquatic organism passage at road-stream crossings—synthesis and guidelines for effectiveness monitoring

USGS Publications Warehouse

Hoffman, Robert L.; Dunham, Jason B.; Hansen, Bruce P.

2012-01-01

Restoration and maintenance of passage for aquatic organisms at road-stream crossings represents a major management priority, involving an investment of hundreds of millions of dollars (for example, U.S. Government Accounting Office, 2001). In recent years, passage at hundreds of crossings has been restored, primarily by replacing barrier road culverts with bridges or stream simulation culverts designed to pass all species and all life stages of aquatic life and simulate natural hydro-geomorphic processes (U.S. Forest Service, 2008). The current situation has motivated two general questions: 1. Are current design standards for stream simulation culverts adequately re-establishing passage for aquatic biota? and 2. How do we monitor and evaluate effectiveness of passage restoration? To address the latter question, a national workshop was held in March 2010, in Portland, Oregon. The workshop included experts on aquatic organism passage from across the nation (see table of participants, APPENDIX) who addressed four classes of methods for monitoring effectiveness of aquatic organism passage—individual movement, occupancy, demography, and genetics. This report has been written, in part, for field biologists who will be undertaking and evaluating the effectiveness of aquatic organism passage restoration projects at road-stream crossings. The report outlines basic methods for evaluating road-stream crossing passage impairment and restoration and discusses under what circumstances and conditions each method will be useful; what questions each method can potentially answer; how to design and implement an evaluation study; and points out the fundamental reality that most evaluation projects will require special funding and partnerships among researchers and resource managers. The report is organized into the following sections, which can be read independently: 1. Historical context: In this section, we provide a brief history of events leading up to the present situation involving aquatic organism passage as a useful context for the issues covered herein. 2. Importance of connectivity for aquatic organisms: In this section, we provide background information regarding the movement characteristics of aquatic organisms and their vulnerability to passage impairment, and the importance of connectivity for a broad diversity of aquatic vertebrates and invertebrates. This section should be useful for practitioners in selecting what species to monitor in relation to aquatic organism passage. 3. Methods for evaluating aquatic organism passage: In this section, we present a range of perspectives on alternatives for assessing and monitoring aquatic organism passage impairment and the effectiveness of passage restoration actions, including the following methods: Individual Movement, Occupancy Models, Abundance (Demography), and Molecular Genetic Markers. 4. Relevance, strengths, and limitations of the four methods: In this section, we discuss the utility of each of the methods as a tool for assessing and quantifying passage impairment and restoration effectiveness. 5. Guidelines for selecting a method: In this section, we review some fundamental criteria and guidelines to consider when selecting a method for monitoring in the context of answering three important questions that should be addressed when developing a plan for evaluating aquatic organism passage. 6. Study and monitoring design considerations: In this section, we discuss four key design elements that need to be considered when developing a monitoring design for assessing passage impairment and restoration. The basic objectives of the report are to: 1. Review the movement characteristics of five groups of aquatic organisms that inhabit streams and to assess their general vulnerability to passage impairment at road-stream crossings; 2. Review four methods for monitoring aquatic organism passage impairment and the effectiveness of actions to restore passage at road-stream crossing structures; 3. Assess the relevance, strengths, and limitations of each method as a monitoring tool; 4. Identify and discuss guidelines that will be useful for selecting a monitoring method; and 5. Discuss what we have identified as the four key elements that need to be considered when developing a monitoring design for assessing passage impairment and restoration at road-stream crossings.

Measurement of the 64Zn,47Ti(n,p) cross sections using a DD neutron generator for medical isotope studies

NASA Astrophysics Data System (ADS)

Voyles, A. S.; Basunia, M. S.; Batchelder, J. C.; Bauer, J. D.; Becker, T. A.; Bernstein, L. A.; Matthews, E. F.; Renne, P. R.; Rutte, D.; Unzueta, M. A.; van Bibber, K. A.

2017-11-01

Cross sections for the 47Ti(n,p)47Sc and 64Zn(n,p)64Cu reactions have been measured for quasi-monoenergetic DD neutrons produced by the UC Berkeley High Flux Neutron Generator (HFNG). The HFNG is a compact neutron generator designed as a "flux-trap" that maximizes the probability that a neutron will interact with a sample loaded into a specific, central location. The study was motivated by interest in the production of 47Sc and 64Cu as emerging medical isotopes. The cross sections were measured in ratio to the 113In(n,n‧)113mIn and 115In(n,n‧)115mIn inelastic scattering reactions on co-irradiated indium samples. Post-irradiation counting using an HPGe and LEPS detectors allowed for cross section determination to within 5% uncertainty. The 64Zn(n,p)64Cu cross section for 2.76-0.02+0.01 MeV neutrons is reported as 49.3 ± 2.6 mb (relative to 113In) or 46.4 ± 1.7 mb (relative to 115In), and the 47Ti(n,p)47Sc cross section is reported as 26.26 ± 0.82 mb. The measured cross sections are found to be in good agreement with existing measured values but with lower uncertainty (<5%), and also in agreement with theoretical values. This work highlights the utility of compact, flux-trap DD-based neutron sources for nuclear data measurements and potentially the production of radionuclides for medical applications.

Effects of instructional strategies using cross sections on the recognition of anatomical structures in correlated CT and MR images.

PubMed

Khalil, Mohammed K; Paas, Fred; Johnson, Tristan E; Su, Yung K; Payer, Andrew F

2008-01-01

This research is an effort to best utilize the interactive anatomical images for instructional purposes based on cognitive load theory. Three studies explored the differential effects of three computer-based instructional strategies that use anatomical cross-sections to enhance the interpretation of radiological images. These strategies include: (1) cross-sectional images of the head that can be superimposed on radiological images, (2) transparent highlighting of anatomical structures in radiological images, and (3) cross-sectional images of the head with radiological images presented side-by-side. Data collected included: (1) time spent on instruction and on solving test questions, (2) mental effort during instruction and test, and (3) students' performance to identify anatomical structures in radiological images. Participants were 28 freshmen medical students (15 males and 13 females) and 208 biology students (190 females and 18 males). All studies used posttest-only control group design, and the collected data were analyzed by either t test or ANOVA. In self-directed computer-based environments, the strategies that used cross sections to improve students' ability to recognize anatomic structures in radiological images showed no significant positive effects. However, when increasing the complexity of the instructional materials, cross-sectional images imposed a higher cognitive load, as indicated by higher investment of mental effort. There is not enough evidence to claim that the simultaneous combination of cross sections and radiological images has no effect on the identification of anatomical structures in radiological images for novices. Further research that control for students' learning and cognitive style is needed to reach an informative conclusion.

Alternative approximation concepts for space frame synthesis

NASA Technical Reports Server (NTRS)

Lust, R. V.; Schmit, L. A.

1985-01-01

A structural synthesis methodology for the minimum mass design of 3-dimensionall frame-truss structures under multiple static loading conditions and subject to limits on displacements, rotations, stresses, local buckling, and element cross-sectional dimensions is presented. A variety of approximation concept options are employed to yield near optimum designs after no more than 10 structural analyses. Available options include: (A) formulation of the nonlinear mathematcal programming problem in either reciprocal section property (RSP) or cross-sectional dimension (CSD) space; (B) two alternative approximate problem structures in each design space; and (C) three distinct assumptions about element end-force variations. Fixed element, design element linking, and temporary constraint deletion features are also included. The solution of each approximate problem, in either its primal or dual form, is obtained using CONMIN, a feasible directions program. The frame-truss synthesis methodology is implemented in the COMPASS computer program and is used to solve a variety of problems. These problems were chosen so that, in addition to exercising the various approximation concepts options, the results could be compared with previously published work.

On the Evolutionary and Biogeographic History of Saxifraga sect. Trachyphyllum (Gaud.) Koch (Saxifragaceae Juss.)

PubMed Central

DeChaine, Eric G.; Anderson, Stacy A.; McNew, Jennifer M.; Wendling, Barry M.

2013-01-01

Arctic-alpine plants in the genus Saxifraga L. (Saxifragaceae Juss.) provide an excellent system for investigating the process of diversification in northern regions. Yet, sect. Trachyphyllum (Gaud.) Koch, which is comprised of about 8 to 26 species, has still not been explored by molecular systematists even though taxonomists concur that the section needs to be thoroughly re-examined. Our goals were to use chloroplast trnL-F and nuclear ITS DNA sequence data to circumscribe the section phylogenetically, test models of geographically-based population divergence, and assess the utility of morphological characters in estimating evolutionary relationships. To do so, we sequenced both genetic markers for 19 taxa within the section. The phylogenetic inferences of sect. Trachyphyllum using maximum likelihood and Bayesian analyses showed that the section is polyphyletic, with S. aspera L. and S bryoides L. falling outside the main clade. In addition, the analyses supported several taxonomic re-classifications to prior names. We used two approaches to test biogeographic hypotheses: i) a coalescent approach in Mesquite to test the fit of our reconstructed gene trees to geographically-based models of population divergence and ii) a maximum likelihood inference in Lagrange. These tests uncovered strong support for an origin of the clade in the Southern Rocky Mountains of North America followed by dispersal and divergence episodes across refugia. Finally we adopted a stochastic character mapping approach in SIMMAP to investigate the utility of morphological characters in estimating evolutionary relationships among taxa. We found that few morphological characters were phylogenetically informative and many were misleading. Our molecular analyses provide a foundation for the diversity and evolutionary relationships within sect. Trachyphyllum and hypotheses for better understanding the patterns and processes of divergence in this section, other saxifrages, and plants inhabiting the North Pacific Rim. PMID:23922810

Recent CCQE results from MINERvA

NASA Astrophysics Data System (ADS)

Ghosh, Anushree; Minerva Collaboration

2017-01-01

The MINER νA detector situated in Fermilab, is designed to make precision cross section measurements for neutrino scattering processes on various nuclei. I will present the two most recent results from the MINER νA charged current quasi-elastic (CCQE) studies. The event sample for both analyses are the CCQE-like final state topology and contain contributions from quasi-elastic and inelastic processes where pions are absorbed in the nucleus. One of the analyses is the MINER νA experiment's first double-differential scattering cross sections for antineutrinos on the hydrocarbon target in the few-GeV range relevant to experiments such as DUNE and NOvA. We compare to models produced by different model generators, and are able to draw first conclusions about the predictions of these models. Another analysis, is the CCQE-like analysis for neutrinos on the nuclear targets of carbon, iron and lead. The ratio of differential cross sections on these targets to the differential cross section on the hydrocarbon target are examined to study nuclear effects.

A study of radar cross section measurement techniques

NASA Technical Reports Server (NTRS)

Mcdonald, Malcolm W.

1986-01-01

Past, present, and proposed future technologies for the measurement of radar cross section were studied. The purpose was to determine which method(s) could most advantageously be implemented in the large microwave anechoic chamber facility which is operated at the antenna test range site. The progression toward performing radar cross section measurements of space vehicles with which the Orbital Maneuvering Vehicle will be called upon to rendezvous and dock is a natural outgrowth of previous work conducted in recent years of developing a high accuracy range and velocity sensing radar system. The radar system was designed to support the rendezvous and docking of the Orbital Maneuvering Vehicle with various other space vehicles. The measurement of radar cross sections of space vehicles will be necessary in order to plan properly for Orbital Maneuvering Vehicle rendezvous and docking assignments. The methods which were studied include: standard far-field measurements; reflector-type compact range measurements; lens-type compact range measurement; near field/far field transformations; and computer predictive modeling. The feasibility of each approach is examined.

Pressure distribution in a converging-diverging nozzle during two-phase choked flow of subcooled nitrogen

NASA Technical Reports Server (NTRS)

Simoneau, R. J.

1975-01-01

Choked flow rates and axial pressure distributions were measured for subcooled nitrogen in a converging-diverging nozzle with a constant area section in the throat region. Stagnation pressures ranged from slightly above saturation to twice the thermodynamic critical pressure. Stagnation temperatures ranged from 0.75 to 1.03 times the thermodynamic critical temperature. The choking plane is at the divergence end of the constant area throat section. At high stagnation pressures the fluid stays liquid well into the constant area throat region; at near saturation stagnation pressures it appears that vaporization occurs at or before the entrance to the constant area throat region. The throat-to-stagnation pressure ratio data exhibits an anomalous flat region, and this anomaly is related to the two-phase process. The fluid is metastably all liquid below the saturation pressure.

Peptide/protein-polymer conjugates: synthetic strategies and design concepts.

PubMed

Gauthier, Marc A; Klok, Harm-Anton

2008-06-21

This feature article provides a compilation of tools available for preparing well-defined peptide/protein-polymer conjugates, which are defined as hybrid constructs combining (i) a defined number of peptide/protein segments with uniform chain lengths and defined monomer sequences (primary structure) with (ii) a defined number of synthetic polymer chains. The first section describes methods for post-translational, or direct, introduction of chemoselective handles onto natural or synthetic peptides/proteins. Addressed topics include the residue- and/or site-specific modification of peptides/proteins at Arg, Asp, Cys, Gln, Glu, Gly, His, Lys, Met, Phe, Ser, Thr, Trp, Tyr and Val residues and methods for producing peptides/proteins containing non-canonical amino acids by peptide synthesis and protein engineering. In the second section, methods for introducing chemoselective groups onto the side-chain or chain-end of synthetic polymers produced by radical, anionic, cationic, metathesis and ring-opening polymerization are described. The final section discusses convergent and divergent strategies for covalently assembling polymers and peptides/proteins. An overview of the use of chemoselective reactions such as Heck, Sonogashira and Suzuki coupling, Diels-Alder cycloaddition, Click chemistry, Staudinger ligation, Michael's addition, reductive alkylation and oxime/hydrazone chemistry for the convergent synthesis of peptide/protein-polymer conjugates is given. Divergent approaches for preparing peptide/protein-polymer conjugates which are discussed include peptide synthesis from synthetic polymer supports, polymerization from peptide/protein macroinitiators or chain transfer agents and the polymerization of peptide side-chain monomers.

Predicting sugar-sweetened behaviours with theory of planned behaviour constructs: Outcome and process results from the SIPsmartER behavioural intervention

PubMed Central

Zoellner, Jamie M.; Porter, Kathleen J.; Chen, Yvonnes; Hedrick, Valisa E.; You, Wen; Hickman, Maja; Estabrooks, Paul A.

2017-01-01

Objective Guided by the theory of planned behaviour (TPB) and health literacy concepts, SIPsmartER is a six-month multicomponent intervention effective at improving SSB behaviours. Using SIPsmartER data, this study explores prediction of SSB behavioural intention (BI) and behaviour from TPB constructs using: (1) cross-sectional and prospective models and (2) 11 single-item assessments from interactive voice response (IVR) technology. Design Quasi-experimental design, including pre- and post-outcome data and repeated-measures process data of 155 intervention participants. Main Outcome Measures Validated multi-item TPB measures, single-item TPB measures, and self-reported SSB behaviours. Hypothesised relationships were investigated using correlation and multiple regression models. Results TPB constructs explained 32% of the variance cross sectionally and 20% prospectively in BI; and explained 13–20% of variance cross sectionally and 6% prospectively. Single-item scale models were significant, yet explained less variance. All IVR models predicting BI (average 21%, range 6–38%) and behaviour (average 30%, range 6–55%) were significant. Conclusion Findings are interpreted in the context of other cross-sectional, prospective and experimental TPB health and dietary studies. Findings advance experimental application of the TPB, including understanding constructs at outcome and process time points and applying theory in all intervention development, implementation and evaluation phases. PMID:28165771

Psychosocial factors at work and self reported health: comparative results of cross sectional and prospective analyses of the French GAZEL cohort

PubMed Central

Niedhammer, I; Chea, M

2003-01-01

Background: Psychosocial factors at work have been found to be significant contributors to health, especially cardiovascular health. Aims: To explore the relation between psychosocial factors at work and self reported health, using cross sectional and prospective analyses for a large occupational cohort of men and women. Methods: Psychosocial factors at work were evaluated using the Karasek questionnaire, designed to measure psychological demands, decision latitude, social support, and physical demands. Self reported health was used as health outcome. Covariates included chronic diseases, and sociodemographic, occupational, and behavioural factors. The cross sectional and prospective analyses concerned respectively 11 447 and 7664 workers. Men and women were analysed separately. Results: Cross sectional analysis revealed significant associations between psychological demands, decision latitude, social support, and physical demands, and self reported health for both men and women. Prospective analysis showed that high psychological demands for both genders, low decision authority for men, and low social support and high physical demands for women were predictive of poor self reported health. These results were independent of potential confounding variables. Conclusions: Results highlight the predictive effects of psychosocial factors at work on self reported health in a one year follow up study. They also underline the need for longitudinal study design and separate analyses for men and women in the field of psychosocial factors at work. PMID:12819285

Understanding Gender, Creativity, and Entrepreneurial Intentions

ERIC Educational Resources Information Center

Smith, Ronda Marie; Sardeshmukh, Shruti R.; Combs, Gwendolyn M.

2016-01-01

Purpose: The purpose of this paper is to explore the complex relationships between gender and entrepreneurial intentions. Design/methodology/approach: This paper uses a two study design where the second study is a constructive replication of the first study. The first study uses a cross-sectional design, while the second uses a design where data…

The effects of road crossings on prairie stream habitat and function

USGS Publications Warehouse

Bouska, Wesley W.; Keane, Timothy; Paukert, Craig P.

2010-01-01

Improperly designed stream crossing structures may alter the form and function of stream ecosystems and habitat and prohibit the movement of aquatic organisms. Stream sections adjoining five concrete box culverts, five low-water crossings (concrete slabs vented by one or multiple culverts), and two large, single corrugated culvert vehicle crossings in eastern Kansas streams were compared to reference reaches using a geomorphologic survey and stream classification. Stream reaches were also compared upstream and downstream of crossings, and crossing measurements were used to determine which crossing design best mimicked the natural dimensions of the adjoining stream. Four of five low-water crossings, three of five box culverts, and one of two large, single corrugated pipe culverts changed classification from upstream to downstream of the crossings. Mean riffle spacing upstream at low-water crossings (8.6 bankfull widths) was double that of downstream reaches (mean 4.4 bankfull widths) but was similar upstream and downstream of box and corrugated pipe culverts. There also appeared to be greater deposition of fine sediments directly upstream of these designs. Box and corrugated culverts were more similar to natural streams than low-water crossings at transporting water, sediments, and debris during bankfull flows.

Static Internal Performance of a Two-Dimensional Convergent-Divergent Nozzle with External Shelf

NASA Technical Reports Server (NTRS)

Lamb, Milton; Taylor, John G.; Frassinelli, Mark C.

1996-01-01

An investigation was conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance of a two-dimensional convergent-divergent nozzle. The nozzle design was tested with dry and afterburning throat areas, which represent different power settings and three expansion ratios. For each of these configurations, three trailing-edge geometries were tested. The baseline geometry had a straight trailing edge. Two different shaping techniques were applied to the baseline nozzle design to reduce radar observables: the scarfed design and the sawtooth design. A flat plate extended downstream of the lower divergent flap trailing edge parallel to the model centerline to form a shelf-like expansion surface. This shelf was designed to shield the plume from ground observation (infrared radiation (IR) signature suppression). The shelf represents the part of the aircraft structure that might be present in an installed configuration. These configurations were tested at nozzle pressure ratios from 2.0 to 12.0.

No evidence for faster male hybrid sterility in population crosses of an intertidal copepod (Tigriopus californicus).

PubMed

Willett, Christopher S

2008-06-01

Two different forces are thought to contribute to the rapid accumulation of hybrid male sterility that has been observed in many inter-specific crosses, namely the faster male and the dominance theories. For male heterogametic taxa, both faster male and dominance would work in the same direction to cause the rapid evolution of male sterility; however, for taxa lacking differentiated sex chromosomes only the faster male theory would explain the rapid evolution of male hybrid sterility. It is currently unknown what causes the faster evolution of male sterility, but increased sexual selection on males and the sensitivity of genes involved in male reproduction are two hypotheses that could explain the observation. Here, patterns of hybrid sterility in crosses of genetically divergent copepod populations are examined to test potential mechanisms of faster male evolution. The study species, Tigriopus californicus, lacks differentiated, hemizygous sex chromosomes and appears to have low levels of divergence caused by sexual selection acting upon males. Hybrid sterility does not accumulate more rapidly in males than females in these crosses suggesting that in this taxon male reproductive genes are not inherently more prone to disruption in hybrids.

Mating patterns and post-mating isolation in three cryptic species of the Engystomops petersi species complex.

PubMed

Trillo, Paula A; Narvaez, Andrea E; Ron, Santiago R; Hoke, Kim L

2017-01-01

Determining the extent of reproductive isolation in cryptic species with dynamic geographic ranges can yield important insights into the processes that generate and maintain genetic divergence in the absence of severe geographic barriers. We studied mating patterns, propensity to hybridize in nature and subsequent fertilization rates, as well as survival and development of hybrid F1 offspring for three nominal species of the Engystomops petersi species complex in Yasuní National Park, Ecuador. We found at least two species in four out of six locations sampled, and 14.3% of the wild pairs genotyped were mixed-species (heterospecific) crosses. We also found reduced fertilization rates in hybrid crosses between E. petersi females and E. "magnus" males, and between E. "magnus" females and E. "selva" males but not in the reciprocal crosses, suggesting asymmetric reproductive isolation for these species. Larval development times decreased in F1 hybrid crosses compared to same species (conspecific) crosses, but we did not find significant reduction in larval survival or early metamorph survival. Our results show evidence of post-mating isolation for at least two hybrid crosses of the cryptic species we studied. The general decrease in fertilization rates in heterospecific crosses suggests that sexual selection and reinforcement might have not only contributed to the pattern of call variation and behavioral isolation we see between species today, but they may also contribute to further signal divergence and behavioral evolution, especially in locations where hybridization is common and fertilization success is diminished.

Singlet fermionic dark matter with Veltman conditions

NASA Astrophysics Data System (ADS)

Kim, Yeong Gyun; Lee, Kang Young; Nam, Soo-hyeon

2018-07-01

We reexamine a renormalizable model of a fermionic dark matter with a gauge singlet Dirac fermion and a real singlet scalar which can ameliorate the scalar mass hierarchy problem of the Standard Model (SM). Our model setup is the minimal extension of the SM for which a realistic dark matter (DM) candidate is provided and the cancellation of one-loop quadratic divergence to the scalar masses can be achieved by the Veltman condition (VC) simultaneously. This model extension, although renormalizable, can be considered as an effective low-energy theory valid up to cut-off energies about 10 TeV. We calculate the one-loop quadratic divergence contributions of the new scalar and fermionic DM singlets, and constrain the model parameters using the VC and the perturbative unitarity conditions. Taking into account the invisible Higgs decay measurement, we show the allowed region of new physics parameters satisfying the recent measurement of relic abundance. With the obtained parameter set, we predict the elastic scattering cross section of the new singlet fermion into target nuclei for a direct detection of the dark matter. We also perform the full analysis with arbitrary set of parameters without the VC as a comparison, and discuss the implication of the constraints by the VC in detail.

Complexity analysis of spontaneous brain activity in mood disorders: A magnetoencephalography study of bipolar disorder and major depression.

PubMed

Fernández, Alberto; Al-Timemy, Ali H; Ferre, Francisco; Rubio, Gabriel; Escudero, Javier

2018-04-26

The lack of a biomarker for Bipolar Disorder (BD) causes problems in the differential diagnosis with other mood disorders such as major depression (MD), and misdiagnosis frequently occurs. Bearing this in mind, we investigated non-linear magnetoencephalography (MEG) patterns in BD and MD. Lempel-Ziv Complexity (LZC) was used to evaluate the resting-state MEG activity in a cross-sectional sample of 60 subjects, including 20 patients with MD, 16 patients with BD type-I, and 24 control (CON) subjects. Particular attention was paid to the role of age. The results were aggregated by scalp region. Overall, MD patients showed significantly higher LZC scores than BD patients and CONs. Linear regression analyses demonstrated distinct tendencies of complexity progression as a function of age, with BD patients showing a divergent tendency as compared with MD and CON groups. Logistic regressions confirmed such distinct relationship with age, which allowed the classification of diagnostic groups. The patterns of neural complexity in BD and MD showed not only quantitative differences in their non-linear MEG characteristics but also divergent trajectories of progression as a function of age. Moreover, neural complexity patterns in BD patients resembled those previously observed in schizophrenia, thus supporting preceding evidence of common neuropathological processes. Copyright © 2018 Elsevier Inc. All rights reserved.

Examining Development of Curriculum Knowledge of Prospective Mathematics Teachers

ERIC Educational Resources Information Center

Sahin, Ömer; Soylu, Yasin

2017-01-01

Explanatory-confirmatory research design, one of the mixed methods research designs, was used in this study to investigate Curriculum Knowledge developments of prospective teachers regarding algebra. Cross-sectional study method, as a type of descriptive research and one of the non-experimental research designs, was used to collect quantitative…

LUX-ZEPLIN (LZ) Technical Design Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mount, B. J.

In this Technical Design Report (TDR) we describe the LZ detector to be built at the Sanford Underground Research Facility (SURF). The LZ dark matter experiment is designed to achieve sensitivity to a WIMP-nucleon spin-independent cross section of three times ten to the negative forty-eighth square centimeters.

Diverging diamond interchange : informational guide.

DOT National Transportation Integrated Search

2014-08-01

This document provides information and guidance on the Diverging Diamond Interchange (DDI). To the extent possible, the guide : addresses a variety of conditions found in the United States, to achieve designs suitable for a wide array of potential us...

Infrared sensor and window system issues

NASA Astrophysics Data System (ADS)

Hargraves, Charles H., Jr.; Martin, James M.

1992-12-01

EO/IR windows are a significant challenge for the weapon system sensor designer who must design for high EO performance, low radar cross section (RCS), supersonic flight, durability, producibility and affordable initial and life cycle costs. This is particularly true in the 8 to 12 micron IR band at which window materials and coating choices are limited by system design requirements. The requirements also drive the optimization of numerous mechanical, optical, materials, and electrical parameters. This paper addresses the EO/IR window as a system design challenge. The interrelationship of the optical, mechanical, and system design processes are examined. This paper presents a summary of the test results, trade studies and analyses that were performed for multi-segment, flight-worthy optical windows with superior optical performance at subsonic and supersonic aircraft velocities and reduced radar cross section. The impact of the window assembly on EO system modulation transfer function (MTF) and sensitivity will be discussed. The use of conductive coatings for shielding/signature control will be discussed.

Development of a Neutron Long Counter Detector for (α, n) Cross Section Measurements at Ohio University

NASA Astrophysics Data System (ADS)

Brandenburg, Kristyn; Meisel, Zach; Brune, Carl R.; Massey, Thomas; Soltesz, Doug; Subedi, Shiv

2017-01-01

The origin of the elements from roughly zinc-to-tin (30 < Z < 50) has yet to be determined. The neutron-rich neutrino driven wind of core collapse supernova (CCSN) is a proposed site for the nucleosynthesis of these elements. However, a significant source of uncertainty exists in elemental abundance yields from astrophysics model calculations due to the uncertainty for (α , n) reaction rates, as most of the relevant cross sections have yet to be measured. We are developing a neutron long counter tailored to measure neutrons for (α , n) reaction measurements performed at The Ohio University Edwards Accelerator Laboratory. The detector design will be optimized using the Monte-Carlo N-Particle transport code (MCNP6). Details of the optimization process, as well as the present status of the detector design will be provided. The plans for first (α , n) cross section measurements will also be briefly discussed. This work was supported in part by the US Department of Energy under Grant Number DE-FG02-88ER40387.

Rational design of the column of a heavy multipurpose machining center

NASA Astrophysics Data System (ADS)

Atapin, V. V.; Kurlaev, N. V.

2016-04-01

The main purpose in the design of supporting constructions of heavy multipurpose machining center is the reduction of mass at the given precision and productivity of machining. Accomplish these ends the technology of rational design of supporting constructions is offered. This technology is based on the decomposition method and the finite elements method in the combination with optimization methods. The technology has four stages: 1) calculation of external forces and loads, 2) as a result the boundary conditions (force, kinematics) for individual supporting constructions are formed, 3) a problem about final optimal distribution of a material by the individual supporting constructions with the real cross-section is solved; 4) dynamic analysis. By the example of design of the column of a heavy multipurpose machining center the main stages of rational design of the individual supporting constructions are shown. At a design stage of the carrying system consisting of load-bearing structures with simplified geometry, optimum overall dimensions of the column are identified. For the admitted system of preferences, it is necessary to accept the fact that the carrying system with the column with the sizes of cross section of 1.8 m (along x axis) and 2.6 m (along y axis) is the best. The analysis of the work of the column under the torsion condition with the use of method of mechanics shows that the column with square cross sections = 2.46·2.46 m which rigidity on torsion is 26 % higher in comparison with a production version is the best. The results of calculation show that a production-release design of the column with longitudinal and transverse edges of rigidity is 24 % heavier than the column with the edges located on a diagonally at equal rigidity.

Lightweight design of automobile frame based on magnesium alloy

NASA Astrophysics Data System (ADS)

Lyu, R.; Jiang, X.; Minoru, O.; Ju, D. Y.

2018-06-01

The structural performance and lightweighting of car base frame design is a challenging task due to all the performance targets that must be satisfied. In this paper, three kinds of materials (iron, aluminum and magnesium alloy) replacement along with section design optimization strategy is proposed to develop a lightweight car frame structure to satisfy the tensile and safety while reducing weight. Two kinds of cross-sections are considered as the design variables. Using Ansys static structure, the design optimization problem is solved, comparing the results of each step, structure of the base flame is optimized for lightweight.

Effect of Cross Sectional Geometry on PDMS Micro Peristaltic Pump Performance: Comparison of SU-8 Replica Molding vs. Micro Injection Molding

PubMed Central

Graf, Neil J.

2013-01-01

Two different fabrication methods were employed to fabricate micropumps with different cross-sectional channel geometries. The first was to fabricate rectangular cross-sectional microchannel geometries using the well known fabrication method of replica molding (REM).1 The second, and far less utilized fabrication technique, was to create microchannel molds using an in-house fabricated handheld micro injection molding apparatus. The injection mold apparatus was designed for use with elastomeric room temperature vulcanization (RTV) polymers, as opposed to most other injection molding machines, which are designed for use with thermoplastic polymers. The injection mold’s bottom plate was used as a microchannel molding template. The molding template was created by threading a small-diameter wire (150 μm or less) through the injection mold’s bottom plate, with subsequent adhesion and smoothing of a thin piece of aluminum foil over the wire-raised injection mold template. When molded against, the template produced a rounded/Gaussian-shaped PDMS microchannel. The design of the injection mold will be presented, along with a direct comparison for micropump performance metrics such as flow rate, valving characteristics, and maximum backpressures attainable for each of the respective micropump channel geometries. PMID:23917263

Estimation of unemployment rates using small area estimation model by combining time series and cross-sectional data

NASA Astrophysics Data System (ADS)

Muchlisoh, Siti; Kurnia, Anang; Notodiputro, Khairil Anwar; Mangku, I. Wayan

2016-02-01

Labor force surveys conducted over time by the rotating panel design have been carried out in many countries, including Indonesia. Labor force survey in Indonesia is regularly conducted by Statistics Indonesia (Badan Pusat Statistik-BPS) and has been known as the National Labor Force Survey (Sakernas). The main purpose of Sakernas is to obtain information about unemployment rates and its changes over time. Sakernas is a quarterly survey. The quarterly survey is designed only for estimating the parameters at the provincial level. The quarterly unemployment rate published by BPS (official statistics) is calculated based on only cross-sectional methods, despite the fact that the data is collected under rotating panel design. The study purpose to estimate a quarterly unemployment rate at the district level used small area estimation (SAE) model by combining time series and cross-sectional data. The study focused on the application and comparison between the Rao-Yu model and dynamic model in context estimating the unemployment rate based on a rotating panel survey. The goodness of fit of both models was almost similar. Both models produced an almost similar estimation and better than direct estimation, but the dynamic model was more capable than the Rao-Yu model to capture a heterogeneity across area, although it was reduced over time.

The Efficiency of Split Panel Designs in an Analysis of Variance Model

PubMed Central

Wang, Wei-Guo; Liu, Hai-Jun

2016-01-01

We consider split panel design efficiency in analysis of variance models, that is, the determination of the cross-sections series optimal proportion in all samples, to minimize parametric best linear unbiased estimators of linear combination variances. An orthogonal matrix is constructed to obtain manageable expression of variances. On this basis, we derive a theorem for analyzing split panel design efficiency irrespective of interest and budget parameters. Additionally, relative estimator efficiency based on the split panel to an estimator based on a pure panel or a pure cross-section is present. The analysis shows that the gains from split panel can be quite substantial. We further consider the efficiency of split panel design, given a budget, and transform it to a constrained nonlinear integer programming. Specifically, an efficient algorithm is designed to solve the constrained nonlinear integer programming. Moreover, we combine one at time designs and factorial designs to illustrate the algorithm’s efficiency with an empirical example concerning monthly consumer expenditure on food in 1985, in the Netherlands, and the efficient ranges of the algorithm parameters are given to ensure a good solution. PMID:27163447

Physicochemical characterization and failure analysis of military coating systems

NASA Astrophysics Data System (ADS)

Keene, Lionel Thomas

Modern military coating systems, as fielded by all branches of the U.S. military, generally consist of a diverse array of organic and inorganic components that can complicate their physicochemical analysis. These coating systems consist of VOC-solvent/waterborne automotive grade polyurethane matrix containing a variety of inorganic pigments and flattening agents. The research presented here was designed to overcome the practical difficulties regarding the study of such systems through the combined application of several cross-disciplinary techniques, including vibrational spectroscopy, electron microscopy, microtomy, ultra-fast laser ablation and optical interferometry. The goal of this research has been to determine the degree and spatial progression of weathering-induced alteration of military coating systems as a whole, as well as to determine the failure modes involved, and characterizing the impact of these failures on the physical barrier performance of the coatings. Transmission-mode Fourier Transform Infrared (FTIR) spectroscopy has been applied to cross-sections of both baseline and artificially weathered samples to elucidate weathering-induced spatial gradients to the baseline chemistry of the coatings. A large discrepancy in physical durability (as indicated by the spatial progression of these gradients) has been found between older and newer generation coatings. Data will be shown implicating silica fillers (previously considered inert) as the probable cause for this behavioral divergence. A case study is presented wherein the application of the aforementioned FTIR technique fails to predict the durability of the coating system as a whole. The exploitation of the ultra-fast optical phenomenon of femtosecond (10-15S) laser ablation is studied as a potential tool to facilitate spectroscopic depth profiling of composite materials. Finally, the interferometric technique of Phase Shifting was evaluated as a potential high-sensitivity technique applied to the problem of determining internal stress evolution in curing and aging coatings.

The Work Disability Functional Assessment Battery (WD-FAB): Feasibility and Psychometric Properties

PubMed Central

Meterko, Mark; Marfeo, Elizabeth E.; McDonough, Christine M.; Jette, Alan M.; Ni, Pengsheng; Bogusz, Kara; Rasch, Elizabeth K; Brandt, Diane E.; Chan, Leighton

2015-01-01

Objectives To assess the feasibility and psychometric properties of eight scales covering two domains of the newly developed Work Disability Functional Assessment Battery (WD-FAB): physical function (PF) and behavioral health (BH) function. Design Cross-sectional. Setting Community. Participants Adults unable to work due to a physical (n=497) or mental (n=476) disability. Interventions None. Main Outcome Measures Each disability group responded to a survey consisting of the relevant WD-FAB scales and existing measures of established validity. The WD-FAB scales were evaluated with regard to data quality (score distribution; percent “I don’t know” responses), efficiency of administration (number of items required to achieve reliability criterion; time required to complete the scale) by computerized adaptive testing (CAT), and measurement accuracy as tested by person fit. Construct validity was assessed by examining both convergent and discriminant correlations between the WD-FAB scales and scores on same-domain and cross-domain established measures. Results Data quality was good and CAT efficiency was high across both WD-FAB domains. Measurement accuracy was very good for the PF scales; BH scales demonstrated more variability. Construct validity correlations, both convergent and divergent, between all WD-FAB scales and established measures were in the expected direction and range of magnitude. Conclusions The data quality, CAT efficacy, person fit and construct validity of the WD-FAB scales were well supported and suggest that the WD-FAB could be used to assess physical and behavioral health function related to work disability. Variation in scale performance suggests the need for future work on item replenishment and refinement, particularly regarding the Self-Efficacy scale. PMID:25528263

An integrated approach to reservoir modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donaldson, K.

1993-08-01

The purpose of this research is to evaluate the usefulness of the following procedural and analytical methods in investigating the heterogeneity of the oil reserve for the Mississipian Big Injun Sandstone of the Granny Creek field, Clay and Roane counties, West Virginia: (1) relational database, (2) two-dimensional cross sections, (3) true three-dimensional modeling, (4) geohistory analysis, (5) a rule-based expert system, and (6) geographical information systems. The large data set could not be effectively integrated and interpreted without this approach. A relational database was designed to fully integrate three- and four-dimensional data. The database provides an effective means for maintainingmore » and manipulating the data. A two-dimensional cross section program was designed to correlate stratigraphy, depositional environments, porosity, permeability, and petrographic data. This flexible design allows for additional four-dimensional data. Dynamic Graphics[sup [trademark

The Causal Effects of Father Absence

PubMed Central

McLanahan, Sara; Tach, Laura; Schneider, Daniel

2014-01-01

The literature on father absence is frequently criticized for its use of cross-sectional data and methods that fail to take account of possible omitted variable bias and reverse causality. We review studies that have responded to this critique by employing a variety of innovative research designs to identify the causal effect of father absence, including studies using lagged dependent variable models, growth curve models, individual fixed effects models, sibling fixed effects models, natural experiments, and propensity score matching models. Our assessment is that studies using more rigorous designs continue to find negative effects of father absence on offspring well-being, although the magnitude of these effects is smaller than what is found using traditional cross-sectional designs. The evidence is strongest and most consistent for outcomes such as high school graduation, children’s social-emotional adjustment, and adult mental health. PMID:24489431

Temporal divergence of percent body fat and body mass index in pre-teenage children: the LOOK longitudinal study.

PubMed

Telford, R D; Cunningham, R B; Abhayaratna, W P

2014-12-01

The index of body mass related to stature, (body mass index, BMI, kgm(-2) ), is widely used as a proxy for percent body fat (%BF) in cross-sectional and longitudinal investigations. BMI does not distinguish between lean and fat mass and in children, the cross-sectional relationship between %BF and BMI changes with age and sex. While BMI increases linearly with age from age 8 to 12 years in both boys and girls, %BF plateaus off between 10 and 12 years. Repeated measures in children show a systematic decrease in %BF for any given BMI from age 8 to 10 to 12 years. Because changes in BMI misrepresent changes in %BF, its use as a proxy of %BF should be avoided in longitudinal studies in this age group. Body mass index (BMI, kgm(-2) ) is commonly used as an indicator of pediatric adiposity, but with its inability to distinguish changes in lean and fat mass, its use in longitudinal studies of children requires careful consideration. To investigate the suitability of BMI as a surrogate of percent body fat (%BF) in pediatric longitudinal investigations. In this longitudinal study, healthy Australian children (256 girls and 278 boys) were measured at ages 8.0 (standard deviation 0.3), 10.0 and 12.0 years for height, weight and percent body fat (%BF) by dual-energy X-ray absorptiometry. The patterns of change in the means of %BF and BMI were different (P < 0.001). While mean BMI increased linearly from 8 to 12 years of age, %BF did not change between 10 and 12 years. Relationships between %BF and BMI in boys and girls were curvilinear and varied with age (P < 0.001) and gender (P < 0.001); any given BMI corresponding with a lower %BF as a child became older. Considering the divergence of temporal patterns of %BF and BMI between 10 and 12 years of age, employment of BMI as a proxy for %BF in absolute or age and sex standardized forms in pediatric longitudinal investigations is problematical. © 2013 The Authors. Pediatric Obesity © 2013 International Association for the Study of Obesity.

Impact of divergent selection for ultimate pH of pectoralis major muscle on biochemical, histological, and sensorial attributes of broiler meat.

PubMed

Alnahhas, N; Le Bihan-Duval, E; Baéza, E; Chabault, M; Chartrin, P; Bordeau, T; Cailleau-Audouin, E; Meteau, K; Berri, C

2015-09-01

The impact of divergent selection based on the ultimate pH (pHu) of pectoralis major (P. major) muscle on the chemical, biochemical, and histological profiles of the muscle and sensorial quality of meat was investigated in broiler chickens. The protein, lipid, DM, glycogen and lactate content, glycolytic potential, proteolysis, lipid and protein oxidation index, muscle fiber cross-sectional area, capillary density, and collagen surface were determined on the breast P. major muscle of 6-wk-old broilers issued from the high-pHu (pHu+) and low-pHu (pHu-) lines. Sensory attributes were also evaluated on the breast (roasted or grilled) and thigh (roasted) meat of the 2 lines. Protein, lipid, and DM content of P. major muscle were not affected by selection ( > 0.05). However, the P. major muscle of the pHu+ line was characterized by lower residual glycogen (-16%; ≤ 0.001) and lactate (-14%; ≤ 0.001) content and lower glycolytic potential (-14%; ≤ 0.001) compared with the pHu- line. Although the average cross-sectional area of muscle fibers and surface occupied by collagen were similar ( > 0.05) in both lines, fewer capillaries per fiber (-15%; ≤ 0.05) were observed in the pHu+ line. The pHu+ line was also characterized by lower lipid oxidation (thiobarbituric acid reactive substance index: -23%; ≤ 0.05) but protein oxidation and proteolysis index were not different ( > 0.05) between the 2 lines. At the sensory level, selection on breast muscle pHu mainly affected the texture of grilled and roast breast meat, which was judged significantly more tender ( ≤ 0.001) in the pHu+ line, and the acid taste, which was less pronounced in the roasted breast meat of the pHu+ line ( ≤ 0.002). This study highlighted that selection based on pHu does not affect the chemical composition and structure of breast meat. However, by modifying muscle blood supply and glycogen turnover, it affects meat acidity and oxidant status, both of which are likely to contribute to the large differences in texture observed between the 2 lines.

Reduction of angular divergence of laser-driven ion beams during their acceleration and transport

NASA Astrophysics Data System (ADS)

Zakova, M.; Pšikal, Jan; Margarone, Daniele; Maggiore, Mario; Korn, G.

2015-05-01

Laser plasma physics is a field of big interest because of its implications in basic science, fast ignition, medicine (i.e. hadrontherapy), astrophysics, material science, particle acceleration etc. 100-MeV class protons accelerated from the interaction of a short laser pulse with a thin target have been demonstrated. With continuing development of laser technology, greater and greater energies are expected, therefore projects focusing on various applications are being formed, e.g. ELIMAIA (ELI Multidisciplinary Applications of laser-Ion Acceleration). One of the main characteristic and crucial disadvantage of ion beams accelerated by ultra-short intense laser pulses is their large divergence, not suitable for the most of applications. In this paper two ways how to decrease beam divergence are proposed. Firstly, impact of different design of targets on beam divergence is studied by using 2D Particlein-cell simulations (PIC). Namely, various types of targets include at foils, curved foil and foils with diverse microstructures. Obtained results show that well-designed microstructures, i.e. a hole in the center of the target, can produce proton beam with the lowest divergence. Moreover, the particle beam accelerated from a curved foil has lower divergence compared to the beam from a flat foil. Secondly, another proposed method for the divergence reduction is using of a magnetic solenoid. The trajectories of the laser accelerated particles passing through the solenoid are modeled in a simple Matlab program. Results from PIC simulations are used as input in the program. The divergence is controlled by optimizing the magnetic field inside the solenoid and installing an aperture in front of the device.

The genomic landscape at a late stage of stickleback speciation: High genomic divergence interspersed by small localized regions of introgression.

PubMed

Ravinet, Mark; Yoshida, Kohta; Shigenobu, Shuji; Toyoda, Atsushi; Fujiyama, Asao; Kitano, Jun

2018-05-01

Speciation is a continuous process and analysis of species pairs at different stages of divergence provides insight into how it unfolds. Previous genomic studies on young species pairs have revealed peaks of divergence and heterogeneous genomic differentiation. Yet less known is how localised peaks of differentiation progress to genome-wide divergence during the later stages of speciation in the presence of persistent gene flow. Spanning the speciation continuum, stickleback species pairs are ideal for investigating how genomic divergence builds up during speciation. However, attention has largely focused on young postglacial species pairs, with little knowledge of the genomic signatures of divergence and introgression in older stickleback systems. The Japanese stickleback species pair, composed of the Pacific Ocean three-spined stickleback (Gasterosteus aculeatus) and the Japan Sea stickleback (G. nipponicus), which co-occur in the Japanese islands, is at a late stage of speciation. Divergence likely started well before the end of the last glacial period and crosses between Japan Sea females and Pacific Ocean males result in hybrid male sterility. Here we use coalescent analyses and Approximate Bayesian Computation to show that the two species split approximately 0.68-1 million years ago but that they have continued to exchange genes at a low rate throughout divergence. Population genomic data revealed that, despite gene flow, a high level of genomic differentiation is maintained across the majority of the genome. However, we identified multiple, small regions of introgression, occurring mainly in areas of low recombination rate. Our results demonstrate that a high level of genome-wide divergence can establish in the face of persistent introgression and that gene flow can be localized to small genomic regions at the later stages of speciation with gene flow.

Single event upset suspectibility testing of the Xilinx Virtex II FPGA

NASA Technical Reports Server (NTRS)

Carmichael, C.; Swift, C.; Yui, G.

2002-01-01

Heavy ion testing of the Xilinx Virtex II was conducted on the configuration, block RAM and user flip flop cells to determine their static single-event upset susceptibility using LETs of 1.2 to 60 MeVcm^2/mg. A software program specifically designed to count errors in the FPGA was used to reveal L1/e, values (the LET at which the cross section is l/e times the saturation cross-section) and single-event functional-interrupt failures.

Testing of tactical performance in youth elite soccer.

PubMed

Memmert, Daniel

2010-01-01

This is a twofold study with the goals of evaluating tactical oriented game test situations for 12-13-year old highly-talented soccer players and to analyze dynamic, intra-individual developments of the players. A cross-sectional design was carried in study 1, using game test situations to measure specific tactics and creative performance for 195 expert players. The results from five evaluation criteria show that both diagnostic instruments can be used for recording football-specific creativity and game intelligence in talented young players. They produced tactical indicators that can be described as objective and valid, exhibit a sufficient degree of differentiation and are easy to record. Study 2 uses a longitudinal design to present a dynamic performance diagnostic tool for analyzing intra-individual improvements of German Soccer Foundation talents according to football-specific creativity and game intelligence. The results with respect to divergent tactical thinking clearly show that very different change processes were observed in the German Soccer Foundation players. Finally, the practical implications for the training process are discussed on the basis of both studies. Key pointsWith game test situations it is possible to assess tactical performance as game intelligence and creativity objective, valid, with a sufficient degree of differentiation, and economically.The results with respect to game intelligence and creativity show that very different change processes were observed in the German Soccer Foundation players dependend on the bases (trainers).Current literature on tactics for school sports as well as for children's, youth and high performance soccer at the club level should place much more emphasis on individual and group-tactical requirements in soccer.

Testing of Tactical Performance in Youth Elite Soccer

PubMed Central

2010-01-01

This is a twofold study with the goals of evaluating tactical oriented game test situations for 12-13-year old highly-talented soccer players and to analyze dynamic, intra-individual developments of the players. A cross-sectional design was carried in study 1, using game test situations to measure specific tactics and creative performance for 195 expert players. The results from five evaluation criteria show that both diagnostic instruments can be used for recording football-specific creativity and game intelligence in talented young players. They produced tactical indicators that can be described as objective and valid, exhibit a sufficient degree of differentiation and are easy to record. Study 2 uses a longitudinal design to present a dynamic performance diagnostic tool for analyzing intra-individual improvements of German Soccer Foundation talents according to football-specific creativity and game intelligence. The results with respect to divergent tactical thinking clearly show that very different change processes were observed in the German Soccer Foundation players. Finally, the practical implications for the training process are discussed on the basis of both studies. Key points With game test situations it is possible to assess tactical performance as game intelligence and creativity objective, valid, with a sufficient degree of differentiation, and economically. The results with respect to game intelligence and creativity show that very different change processes were observed in the German Soccer Foundation players dependend on the bases (trainers). Current literature on tactics for school sports as well as for children’s, youth and high performance soccer at the club level should place much more emphasis on individual and group-tactical requirements in soccer. PMID:24149686

Quantifying fish habitat associated with stream simulation design culverts in northern Wisconsin

Treesearch

A. Timm; D. Higgins; J. Stanovick; R. Kolka; S. Eggert

2017-01-01

This study investigated the effects of culvert replacement design on fish habitat and fish weight by comparing substrate diversity and weight at three stream simulation (SS)-design and three bankfull and backwater (BB)-design sites on the Chequamegon-Nicolet National Forest, Wisconsin. Stream channel cross-sections, Wolman substrate particle counts, and single-pass...

Testing a Longitudinal Integrated Self-Efficacy and Self-Determination Theory Model for Physical Activity Post-Cardiac Rehabilitation

PubMed Central

Sweet, Shane N.; Fortier, Michelle S.; Strachan, Shaelyn M.; Blanchard, Chris M.; Boulay, Pierre

2014-01-01

Self-determination theory and self-efficacy theory are prominent theories in the physical activity literature, and studies have begun integrating their concepts. Sweet, Fortier, Strachan and Blanchard (2012) have integrated these two theories in a cross-sectional study. Therefore, this study sought to test a longitudinal integrated model to predict physical activity at the end of a 4-month cardiac rehabilitation program based on theory, research and Sweet et al.’s cross-sectional model. Participants from two cardiac rehabilitation programs (N=109) answered validated self-report questionnaires at baseline, two and four months. Data were analyzed using Amos to assess the path analysis and model fit. Prior to integration, perceived competence and self-efficacy were combined, and labeled as confidence. After controlling for 2-month physical activity and cardiac rehabilitation site, no motivational variables significantly predicted residual change in 4-month physical activity. Although confidence at two months did not predict residual change in 4-month physical activity, it had a strong positive relationship with 2-month physical activity (β=0.30, P<0.001). The overall model retained good fit indices. In conclusion, results diverged from theoretical predictions of physical activity, but self-determination and self-efficacy theory were still partially supported. Because the model had good fit, this study demonstrated that theoretical integration is feasible. PMID:26973926

Singular lensing from the scattering on special space-time defects

NASA Astrophysics Data System (ADS)

Mavromatos, Nick E.; Papavassiliou, Joannis

2018-01-01

It is well known that certain special classes of self-gravitating point-like defects, such as global (non gauged) monopoles, give rise to non-asymptotically flat space-times characterized by solid angle deficits, whose size depends on the details of the underlying microscopic models. The scattering of electrically neutral particles on such space-times is described by amplitudes that exhibit resonant behaviour when thescattering and deficit angles coincide. This, in turn, leads to ring-like structures where the cross sections are formally divergent ("singular lensing"). In this work, we revisit this particular phenomenon, with the twofold purpose of placing it in a contemporary and more general context, in view of renewed interest in the theory and general phenomenology of such defects, and, more importantly, of addressing certain subtleties that appear in the particular computation that leads to the aforementioned effect. In particular, by adopting a specific regularization procedure for the formally infinite Legendre series encountered, we manage to ensure the recovery of the Minkowski space-time, and thus the disappearance of the lensing phenomenon, in the no-defect limit, and the validity of the optical theorem for the elastic total cross section. In addition, the singular nature of the phenomenon is confirmed by means of an alternative calculation, which, unlike the original approach, makes no use of the generating function of the Legendre polynomials, but rather exploits the asymptotic properties of the Fresnel integrals.

The Expression of Backwater Dynamics in the Morphology, Kinematics and Deposit Architecture of Fluvio-deltaic Channels

NASA Astrophysics Data System (ADS)

Fernandes, A. M.; Smith, V.

2017-12-01

A downstream reduction in bed material flux is associated with the backwater zone, where rivers in their terminal reaches deepen to respond to the sea-level in the receiving basin. This downstream change in sediment transport is reflected in: a) lateral channel mobility, and b) sedimentology and stratigraphic architecture of composite depositional bodies that are left behind. Here we draw comparisons between the Mississippi River and the Trinity River (TX), in terms of bar morphologies and composition, and lateral mobility of these rivers. Across the backwater transition, both rivers display a slight increase in lateral migration rates, followed by substantial decrease lateral migration in the terminal reaches. Both rivers also display predominantly symmetrical channel cross-sections, coincident with very small migration rates in the terminal reaches. We will discuss how the divergence in sediment transport flux across the backwater zone relates to the volume and shape of bank-attached bars, which in turn relates to the cross-sectional shapes of the channels as well as their lateral migrations rates, and ultimately defines the internal architecture of the composite channel deposits that result. Furthermore, we draw comparisons between the morphologies of bank-attached bars and channels in rivers and submarine channels to present insights into how the dominant mode of sediment transport in these different environments ultimately controls the morphologies and kinematics of these channels.

Correlative Magnetic Imaging of Heat-Assisted Magnetic Recording Media in Cross Section Using Lorentz TEM and MFM

DOE PAGES

Kim, Taeho Roy; Phatak, Charudatta; Petford-Long, Amanda K.; ...

2017-10-23

In order to increase the storage density of hard disk drives, a detailed understanding of the magnetic structure of the granular magnetic layer is essential. Here, we demonstrate an experimental procedure of imaging recorded bits on heat-assisted magnetic recording (HAMR) media in cross section using Lorentz transmission electron microscopy (TEM). With magnetic force microscopy and focused ion beam (FIB), we successfully targeted a single track to prepare cross-sectional TEM specimens. Then, we characterized the magnetic structure of bits with their precise location and orientation using Fresnel mode of Lorentz TEM. Here, this method can promote understanding of the correlation betweenmore » bits and their material structure in HAMR media to design better the magnetic layer.« less

Correlative Magnetic Imaging of Heat-Assisted Magnetic Recording Media in Cross Section Using Lorentz TEM and MFM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Taeho Roy; Phatak, Charudatta; Petford-Long, Amanda K.

In order to increase the storage density of hard disk drives, a detailed understanding of the magnetic structure of the granular magnetic layer is essential. Here, we demonstrate an experimental procedure of imaging recorded bits on heat-assisted magnetic recording (HAMR) media in cross section using Lorentz transmission electron microscopy (TEM). With magnetic force microscopy and focused ion beam (FIB), we successfully targeted a single track to prepare cross-sectional TEM specimens. Then, we characterized the magnetic structure of bits with their precise location and orientation using Fresnel mode of Lorentz TEM. Here, this method can promote understanding of the correlation betweenmore » bits and their material structure in HAMR media to design better the magnetic layer.« less

An instrument for monitoring stump oedema and shrinkage in amputees.

PubMed

Fernie, G R; Holliday, P J; Lobb, R J

1978-08-01

A new system for measuring the cross-sectional area profiles of amputation stumps and whole limbs has been designed at the Amputee Research Centre. The instrument consists of a cylindrical tank supported on an elevator. The tank is raised to the height of the amputation stump and filled with water. A graph of the cross-sectional area profile of the amputation stump is generated by a mini-computer as the elevator descends. The cross-sectional area (A) is calculated from the expression: formula: (see text) where Hw = height of water in the tank He = height of the elevator Ac = a constant, related to the size of the measuring tank. This paper describes the instrument, which may find application in many other areas where there is a need to study shape.

Brown Adipose Tissue and Its Relationship to Bone Structure in Pediatric Patients

PubMed Central

Ponrartana, Skorn; Aggabao, Patricia C.; Hu, Houchun H.; Aldrovandi, Grace M.; Wren, Tishya A. L.

2012-01-01

Context: Emerging evidence suggests a possible link between brown adipose tissue (BAT) and bone metabolism. Objective: The objective of this study was to examine the relationships between BAT and bone cross-sectional dimensions in children and adolescents. Design: This was a cross-sectional study. Setting: The study was conducted at a pediatric referral center. Patients: Patients included 40 children and teenagers (21 males and 19 females) successfully treated for pediatric malignancies. Interventions: There were no interventions. Main Outcome Measures: The volume of BAT was determined by fluorodeoxyglucose-positron emission tomography/computed tomography. Measures of the cross-sectional area and cortical bone area and measures of thigh musculature and sc fat were determined at the midshaft of the femur. Results: Regardless of sex, there were significant correlations seen between BAT volume and the cross-sectional dimensions of the bone (r values between 0.68 and 0.77; all P ≤ 0 .001). Multiple regression analyses indicated that the volume of BAT predicted femoral cross-sectional area and cortical bone area, even after accounting for height, weight, and gender. The addition of muscle as an independent variable increased the predictive power of the model but significantly decreased the contribution of BAT. Conclusions: The volume of BAT is positively associated with the amount of bone and the cross-sectional size of the femur in children and adolescents. This relation between BAT and bone structure could, at least in part, be mediated by muscle. PMID:22593587

The Influence of the Aerodynamic Span Effect on the Magnitude of the Torsional-divergence Velocity and on the Shape of the Corresponding Deflection Mode

NASA Technical Reports Server (NTRS)

Hildebrand, Francis B; Reissner, Eric

1944-01-01

A procedure which takes into account the aerodynamic span effect is given for the determination of the torsional-divergence velocities of monoplanes. The explicit solutions obtained in several cases indicate that the aerodynamic span effect may increase the divergence velocities found by means of the section-force theory by as much as 17 to 40 percent. It is found that the magnitude of the effect increases with increasing degree of stiffness taper and decreases with increasing degree of chord taper. By a slight extension of the present method it is possible to analyze the elastic deformations of wings, and the resultant lift distributions, before torsional divergence occurs.

An Investigation of Fat Infiltration of the Multifidus Muscle in Patients With Severe Neck Symptoms Associated With Chronic Whiplash-Associated Disorder.

PubMed

Karlsson, Anette; Leinhard, Olof Dahlqvist; Åslund, Ulrika; West, Janne; Romu, Thobias; Smedby, Örjan; Zsigmond, Peter; Peolsson, Anneli

2016-10-01

Study Design Cross-sectional study. Background Findings of fat infiltration in cervical spine multifidus, as a sign of degenerative morphometric changes due to whiplash injury, need to be verified. Objectives To develop a method using water/fat magnetic resonance imaging (MRI) to investigate fat infiltration and cross-sectional area of multifidus muscle in individuals with whiplash-associated disorders (WADs) compared to healthy controls. Methods Fat infiltration and cross-sectional area in the multifidus muscles spanning the C4 to C7 segmental levels were investigated by manual segmentation using water/fat-separated MRI in 31 participants with WAD and 31 controls, matched for age and sex. Results Based on average values for data spanning C4 to C7, participants with severe disability related to WAD had 38% greater muscular fat infiltration compared to healthy controls (P = .03) and 45% greater fat infiltration compared to those with mild to moderate disability related to WAD (P = .02). There were no significant differences between those with mild to moderate disability and healthy controls. No significant differences between groups were found for multifidus cross-sectional area. Significant differences were observed for both cross-sectional area and fat infiltration between segmental levels. Conclusion Participants with severe disability after a whiplash injury had higher fat infiltration in the multifidus compared to controls and to those with mild/moderate disability secondary to WAD. Earlier reported findings using T1-weighted MRI were reproduced using refined imaging technology. The results of the study also indicate a risk when segmenting single cross-sectional slices, as both cross-sectional area and fat infiltration differ between cervical levels. J Orthop Sports Phys Ther 2016;46(10):886-893. Epub 2 Sep 2016. doi:10.2519/jospt.2016.6553.

Measurement of the scattering cross section of slow neutrons on liquid parahydrogen from neutron transmission

DOE PAGES

Grammer, K. B.; Alarcon, R.; Barrón-Palos, L.; ...

2015-05-08

Liquid hydrogen is a dense Bose fluid whose equilibrium properties are both calculable from first principles using various theoretical approaches and of interest for the understanding of a wide range of questions in many-body physics. Unfortunately, the pair correlation function g(r) inferred from neutron scattering measurements of the differential cross section dσ/dΩ from different measurements reported in the literature are inconsistent. We have measured the energy dependence of the total cross section and the scattering cross section for slow neutrons with energies between 0.43 and 16.1 meV on liquid hydrogen at 15.6 K (which is dominated by the parahydrogen component)more » using neutron transmission measurements on the hydrogen target of the NPDGamma collaboration at the Spallation Neutron Source at Oak Ridge National Laboratory. The relationship between the neutron transmission measurement we perform and the total cross section is unambiguous, and the energy range accesses length scales where the pair correlation function is rapidly varying. At 1 meV our measurement is a factor of 3 below the data from previous work. We present evidence that these previous measurements of the hydrogen cross section, which assumed that the equilibrium value for the ratio of orthohydrogen and parahydrogen has been reached in the target liquid, were in fact contaminated with an extra nonequilibrium component of orthohydrogen. Liquid parahydrogen is also a widely used neutron moderator medium, and an accurate knowledge of its slow neutron cross section is essential for the design and optimization of intense slow neutron sources. Furthermore, we describe our measurements and compare them with previous work.« less

Measuring and Validating Neutron Capture Cross Sections Using a Lead Slowing-Down Spectrometer

NASA Astrophysics Data System (ADS)

Thompson, Nicholas

Accurate nuclear data is essential for the modeling, design, and operation of nuclear systems. In this work, the Rensselaer Polytechnic Institute (RPI) Lead Slowing-Down Spectrometer (LSDS) at the Gaerttner Linear Accelerator Center (LINAC) was used to measure neutron capture cross sections and validate capture cross sections in cross section libraries. The RPI LINAC was used to create a fast burst of neutrons in the center of the LSDS, a large cube of high purity lead. A sample and YAP:Ce scintillator were placed in the LSDS, and as neutrons lost energy through scattering interactions with the lead, the scintillator detected capture gammas resulting from neutron capture events in the sample. Samples of silver, gold, cobalt, iron, indium, molybdenum, niobium, nickel, tin, tantalum, and zirconium were measured. Data was collected as a function of time after neutron pulse, or slowing-down time, which is correlated to average neutron energy. An analog and a digital data acquisition system collected data simultaneously, allowing for collection of pulse shape information as well as timing. Collection of digital data allowed for pulse shape analysis after the experiment. This data was then analyzed and compared to Monte Carlo simulations to validate the accuracy of neutron capture cross section libraries. These measurements represent the first time that neutron capture cross sections have been measured using an LSDS in the United States, and the first time tools such as coincidence measurements and pulse height weighting have been applied to measurements of neutron capture cross sections using an LSDS. Significant differences between measurement results and simulation results were found in multiple materials, and some errors in nuclear data libraries have already been identified due to these measurements.

Diverging patterns with endogenous labor migration.

PubMed

Reichlin, P; Rustichini, A

1998-05-05

"The standard neoclassical model cannot explain persistent migration flows and lack of cross-country convergence when capital and labor are mobile. Here we present a model where both phenomena may take place.... Our model is based on the Arrow-Romer approach to endogenous growth theory. We single out the importance of a (however weak) scale effect from the size of the workforce.... The main conclusion of this simple model is that lack of convergence, or even divergence, among countries is possible, even with perfect capital mobility and labor mobility." excerpt

Vector splines on the sphere with application to the estimation of vorticity and divergence from discrete, noisy data

NASA Technical Reports Server (NTRS)

Wahba, G.

1982-01-01

Vector smoothing splines on the sphere are defined. Theoretical properties are briefly alluded to. The appropriate Hilbert space norms used in a specific meteorological application are described and justified via a duality theorem. Numerical procedures for computing the splines as well as the cross validation estimate of two smoothing parameters are given. A Monte Carlo study is described which suggests the accuracy with which upper air vorticity and divergence can be estimated using measured wind vectors from the North American radiosonde network.

Age-related sex differences in body condition and telomere dynamics of red-sided garter snakes

PubMed Central

Rollings, Nicky; Uhrig, Emily J.; Krohmer, Randolph W.; Waye, Heather L.; Mason, Robert T.; Olsson, Mats; Whittington, Camilla M.

2017-01-01

Life-history strategies vary dramatically between the sexes, which may drive divergence in sex-specific senescence and mortality rates. Telomeres are tandem nucleotide repeats that protect the ends of chromosomes from erosion during cell division. Telomeres have been implicated in senescence and mortality because they tend to shorten with stress, growth and age. We investigated age-specific telomere length in female and male red-sided garter snakes, Thamnophis sirtalis parietalis. We hypothesized that age-specific telomere length would differ between males and females given their divergent reproductive strategies. Male garter snakes emerge from hibernation with high levels of corticosterone, which facilitates energy mobilization to fuel mate-searching, courtship and mating behaviours during a two to four week aphagous breeding period at the den site. Conversely, females remain at the dens for only about 4 days and seem to invest more energy in growth and cellular maintenance, as they usually reproduce biennially. As male investment in reproduction involves a yearly bout of physiologically stressful activities, while females prioritize self-maintenance, we predicted male snakes would experience more age-specific telomere loss than females. We investigated this prediction using skeletochronology to determine the ages of individuals and qPCR to determine telomere length in a cross-sectional study. For both sexes, telomere length was positively related to body condition. Telomere length decreased with age in male garter snakes, but remained stable in female snakes. There was no correlation between telomere length and growth in either sex, suggesting that our results are a consequence of divergent selection on life histories of males and females. Different selection on the sexes may be the physiological consequence of the sexual dimorphism and mating system dynamics displayed by this species. PMID:28381620

Age-related sex differences in body condition and telomere dynamics of red-sided garter snakes.

PubMed

Rollings, Nicky; Uhrig, Emily J; Krohmer, Randolph W; Waye, Heather L; Mason, Robert T; Olsson, Mats; Whittington, Camilla M; Friesen, Christopher R

2017-04-12

Life-history strategies vary dramatically between the sexes, which may drive divergence in sex-specific senescence and mortality rates. Telomeres are tandem nucleotide repeats that protect the ends of chromosomes from erosion during cell division. Telomeres have been implicated in senescence and mortality because they tend to shorten with stress, growth and age. We investigated age-specific telomere length in female and male red-sided garter snakes, Thamnophis sirtalis parietalis We hypothesized that age-specific telomere length would differ between males and females given their divergent reproductive strategies. Male garter snakes emerge from hibernation with high levels of corticosterone, which facilitates energy mobilization to fuel mate-searching, courtship and mating behaviours during a two to four week aphagous breeding period at the den site. Conversely, females remain at the dens for only about 4 days and seem to invest more energy in growth and cellular maintenance, as they usually reproduce biennially. As male investment in reproduction involves a yearly bout of physiologically stressful activities, while females prioritize self-maintenance, we predicted male snakes would experience more age-specific telomere loss than females. We investigated this prediction using skeletochronology to determine the ages of individuals and qPCR to determine telomere length in a cross-sectional study. For both sexes, telomere length was positively related to body condition. Telomere length decreased with age in male garter snakes, but remained stable in female snakes. There was no correlation between telomere length and growth in either sex, suggesting that our results are a consequence of divergent selection on life histories of males and females. Different selection on the sexes may be the physiological consequence of the sexual dimorphism and mating system dynamics displayed by this species. © 2017 The Author(s).

Digital database of channel cross-section surveys, Mount St. Helens, Washington

USGS Publications Warehouse

Mosbrucker, Adam R.; Spicer, Kurt R.; Major, Jon J.; Saunders, Dennis R.; Christianson, Tami S.; Kingsbury, Cole G.

2015-08-06

Stream-channel cross-section survey data are a fundamental component to studies of fluvial geomorphology. Such data provide important parameters required by many open-channel flow models, sediment-transport equations, sediment-budget computations, and flood-hazard assessments. At Mount St. Helens, Washington, the long-term response of channels to the May 18, 1980, eruption, which dramatically altered the hydrogeomorphic regime of several drainages, is documented by an exceptional time series of repeat stream-channel cross-section surveys. More than 300 cross sections, most established shortly following the eruption, represent more than 100 kilometers of surveyed topography. Although selected cross sections have been published previously in print form, we present a comprehensive digital database that includes geospatial and tabular data. Furthermore, survey data are referenced to a common geographic projection and to common datums. Database design, maintenance, and data dissemination are accomplished through a geographic information system (GIS) platform, which integrates survey data acquired with theodolite, total station, and global navigation satellite system (GNSS) instrumentation. Users can interactively perform advanced queries and geospatial time-series analysis. An accuracy assessment provides users the ability to quantify uncertainty within these data. At the time of publication, this project is ongoing. Regular database updates are expected; users are advised to confirm they are using the latest version.

Dye lasing arrangement including an optical assembly for altering the cross-section of its pumping beam and method

DOEpatents

O'Neil, Richard W.; Sweatt, William C.

1992-01-01

An optical assembly is disclosed herein along with a method of operation for use in a dye lasing arrangement, for example a dye laser oscillator or a dye amplifier, in which a continuous stream of dye is caused to flow through a given zone in a cooperating dye chamber while the zone is being illuminated by light from a pumping beam which is directed into the given zone. This in turn causes the dye therein to lase and thereby produce a new dye beam in the case of a dye laser oscillator or amplify a dye beam in the case of a dye amplifier. The optical assembly so disclosed is designed to alter the pump beam such that the beam enters the dye chamber with a different cross-sectional configuration, preferably one having a more uniform intensity profile, than its initially produced cross-sectional configuration. To this end, the assembly includes a network of optical components which first act on the beam while the latter retains its initially produced cross-sectional configuration for separating it into a plurality of predetermined segments and then recombines the separated components in a predetermined way which causes the recombined beam to have the different cross-sectional configuration.

Study of the Integration of the CNU-TS-1 Mobile Tunnel Monitoring System.

PubMed

Du, Liming; Zhong, Ruofei; Sun, Haili; Zhu, Qiang; Zhang, Zhen

2018-02-01

A rapid, precise and automated means for the regular inspection and maintenance of a large number of tunnels is needed. Based on the depth study of the tunnel monitoring method, the CNU-TS-1 mobile tunnel monitoring system (TS1) is developed and presented. It can efficiently obtain the cross-sections that are orthogonal to the tunnel in a dynamic way, and the control measurements that depend on design data are eliminated. By using odometers to locate the cross-sections and correcting the data based on longitudinal joints of tunnel segment lining, the cost of the system has been significantly reduced, and the interval between adjacent cross-sections can reach 1-2 cm when pushed to collect data at a normal walking speed. Meanwhile, the relative deformation of tunnel can be analyzed by selecting cross-sections from original data. Through the measurement of the actual tunnel, the applicability of the system for tunnel deformation detection is verified, and the system is shown to be 15 times more efficient than that of the total station. The simulation experiment of the tunnel deformation indicates that the measurement accuracy of TS1 for cross-sections is 1.1 mm. Compared with the traditional method, TS1 improves the efficiency as well as increases the density of the obtained points.

Internal-Film Cooling of Rocket Nozzles

NASA Technical Reports Server (NTRS)

Sloop, J L; Kinney, George R

1948-01-01

Experiments were conducted with 1000-pound-thrust rocket engine to determine feasibility of cooling convergent-divergent nozzle by internal film of water introduced at nozzle entrance. Water flow of 3 percent of propellant flow reduced heat flow into nozzle to 55 percent of uncooled heat flow. Introduction of water by porous ring before nozzle resulted in more uniform coverage of nozzle than water introduced by single arrangement of 36 jets directed along nozzle wall. Water flow through porous ring of 3.5 percent of propellant flow stabilized wall temperature in convergent section but did not adequately cool throat or divergent sections.

Absence of intrinsic post-zygotic incompatibilities in artificial crosses between sympatric coregonid species from upper Lake Constance.

PubMed

Eckmann, R

2015-05-01

A full factorial crossing experiment with five females and five males of each of two coregonid species from upper Lake Constance was used to test for intrinsic post-zygotic incompatibilities during early ontogeny. Up until shortly before hatching, there was no difference in embryo mortality between homo and heterologous crosses. A maternal effect on mortality was found in both species, but paternal effects and female-male interactions were absent. Thus, genetic incompatibility during early ontogeny does not appear to prevent introgressive hybridization, suggesting that genetic divergence between these species is maintained primarily by pre-zygotic barriers. The recent genetic homogenizations of coregonid species flocks in European alpine lakes may have been caused by a flattening of adaptive landscapes through eutrophication, but intensive stocking with larvae obtained in hatcheries from artificially fertilized eggs is also likely to be a contributing factor. To safeguard diversity among sympatric coregonids, it is important to re-establish ecological conditions conducive to species divergence and to revise traditional management strategies. © 2015 The Fisheries Society of the British Isles.

Determination of Optimum Cross-section for Oran Highway Revetment

NASA Astrophysics Data System (ADS)

Sogut, E.; Velioglu, D.; Guler, I.

2016-12-01

Revetments are shore parallel, sloping coastal structures which are built to provide protection from the negative effects of the sea. The revetment mentioned in this study is located in the City of Oran, Algeria and is currently under construction. This study investigates the determination of the optimum revetment cross section for Oran highway, considering both the hydraulic stability of the revetment and economy. The existence of cliffs in the region and the settlement of the City of Oran created a necessity to re-align Oran highway; therefore, it was shifted towards the Gulf of Oran. Approximately 1 km of the highway is to be constructed on the Mediterranean Sea due to the new alignment. In order to protect the sea side of the road from the adverse effects of the sea, a revetment was designed. The proposed cross section had an armour layer composed of 23 tons of antifer units and regular placement of armour units was recommended. In order to check the hydraulic stability of the proposed section, physical model tests were performed in the laboratory of LEM (Laboratoire d'Etudes Maritimes) in Algeria, using the pre-determined design wave conditions. The physical model tests revealed that the trunk of the revetment was totaly damaged. Accordingly, the proposed section was found insufficient and certain modifications were required. The first modification was made in the arrangement of armour units, changing them from regular to irregular. After testing the new cross section, it was observed that the revetment was vulnerable to breaking wave attack due to the toe geometry and thus the toe of the revetment had to be re-shaped. Therefore, the second option was to reduce the toe elevation. It was observed that even though the revetment trunk was safe, the damage in the toe was not in acceptable limits. The new cross section was found insufficient and as the final option, the weight of the antifer units used in the armour layer was increased, the toe length of the structure was increased and the size of the armour units in the toe was decreased. After the modifications, the new section was tested physically and it was selected as the most optimum option.

Low-head feeding system for thin section castings

DOEpatents

Daniel, Sabah S.; Kleeb, Thomas R.; Lewis, Thomas W.; McDermott, John F.; Ozgu, Mustafa R.; Padfield, Ralph C.; Rego, Donovan N.; Vassilicos, Achilles

1990-01-01

A feed system is provided for conveying molten metal to a thin section caster having mold surfaces moving exclusively in the direction of casting. The feed system has a passage of circular cross section adjacent to one end thereof for receiving molten metal and a rectangular cross section at the delivery end thereof adjacent to the caster. The feed system is designed for supplying molten metal to the caster at low pressure for "closed-pool" type caster operation. The point of highest elevation in the metal flow passage of the feed system is on the upper surface of a transition portion where the cross section changes from circular to rectangular adjacent to the nozzle. The level or height of the high point above the centerline of the nozzle exit is selected so as to be less than the pressure of the metal measured in inches at the nozzle exit. This feature enables the maintenance of positive pressure in the metal within the feed system so that ingress of air into the metal is prevented.

Introgressive Hybridization between Anciently Diverged Lineages of Silene (Caryophyllaceae)

PubMed Central

Petri, Anna; Pfeil, Bernard E.; Oxelman, Bengt

2013-01-01

Hybridization has played a major role during the evolution of angiosperms, mediating both gene flow between already distinct species and the formation of new species. Newly formed hybrids between distantly related taxa are often sterile. For this reason, interspecific crosses resulting in fertile hybrids have rarely been described to take place after more than a few million years after divergence. We describe here the traces of a reproductively successful hybrid between two ancestral species of Silene, diverged for about six million years prior to hybridization. No extant hybrids between the two parental lineages are currently known, but introgression of the RNA polymerase gene NRPA2 provides clear evidence of a temporary and fertile hybrid. Parsimony reconciliation between gene trees and the species tree, as well as consideration of clade ages, help exclude gene paralogy and lineage sorting as alternative hypotheses. This may represent one of the most extreme cases of divergence between species prior to introgressive hybridization discovered yet, notably at a homoploid level. Although species boundaries are generally believed to be stable after millions of years of divergence, we believe that this finding may indicate that gene flow between distantly related species is merely largely undetected at present. PMID:23861793

Knowledge of Metabolic Syndrome in Chinese Adults: Implications for Health Education

ERIC Educational Resources Information Center

Lo, Sally Wai Sze; Chair, Sek Ying; Lee, Iris Fung Kam

2016-01-01

Objective: The objective of this study was to assess knowledge of metabolic syndrome (MS) among Chinese adults and provide directions for designing healthcare promotion schemes for improving MS awareness in the community. Design: The study adopted a cross-sectional design and a convenience sampling method. Method: Chinese adults aged 18-65 years…

Evaluation of AM2 2 1 Lay Pattern Over a 25 CBR Subgrade

DTIC Science & Technology

2018-04-30

penetrometer in shallow pavement applications. Designation : D 6951. West Conshohocken, PA: ASTM International. ____. 2010. Standard test method for...Department of the Army position unless so designated by other authorized documents. DESTROY THIS REPORT WHEN NO LONGER NEEDED. DO NOT RETURN IT TO...27 Figure 3.21. Surveying designated cross section

Design, Analysis, and On-Sun Evaluation of Reflective Strips Under Controlled Buckling

NASA Technical Reports Server (NTRS)

Jaworske, Donald A.; Sechkar, Edward A.; Colozza, Anthony J.

2014-01-01

Solar concentrators are envisioned for use in a variety of space-based applications, including applications involving in situ resource utilization. Identifying solar concentrators that minimize mass and cost are of great interest, especially since launch cost is driven in part by the mass of the payload. Concentrators must also be able to survive the wide temperature excursions on the lunar surface. Identifying smart structures which compensate for changes in concentrator geometry brought about by temperature extremes are of interest. Some applications may benefit from the ability to change the concentrators focal pattern at will. This paper addresses a method of designing a single reflective strip to produce a desired focal pattern through the use of controlled buckling. Small variations in the cross section over the length of the reflective strip influence the distribution of light in the focal region. A finite element method of analysis is utilized here which calculates the curve produced for a given strip cross section and axial load. Varying axial force and strip cross section over the length of the reflective strip provide a means of optimizing ray convergence in the focal region. Careful selection of a tapered cross section yields a reflective strip that approximates a parabola. An array of reflective strips under controlled buckling produces a light weight concentrator and adjustments in the compression of individual strips provide a means of compensating for temperature excursions or changing the focal pattern at will.

Design, Analysis, and On-Sun Evaluation of Reflective Strips Under Controlled Buckling

NASA Technical Reports Server (NTRS)

Jaworske, D. A.; Sechkar, E. A.; Colozza, A. J.

2014-01-01

Solar concentrators are envisioned for use in a variety of space-based applications, including applications involving in situ resource utilization. Identifying solar concentrators that minimize mass and cost are of great interest, especially since launch cost is driven in part by the mass of the payload. Concentrators must also be able to survive the wide temperature excursions on the lunar surface. Identifying smart structures which compensate for changes in concentrator geometry brought about by temperature extremes are of interest. Some applications may benefit from the ability to change the concentrator's focal pattern at will. This paper addresses a method of designing a single reflective strip to produce a desired focal pattern through the use of controlled buckling. Small variations in the cross section over the length of the reflective strip influence the distribution of light in the focal region. A finite element method of analysis is utilized here which calculates the curve produced for a given strip cross section and axial load. Varying axial force and strip cross section over the length of the reflective strip provide a means of optimizing ray convergence in the focal region. Careful selection of a tapered cross section yields a reflective strip that approximates a parabola. An array of reflective strips under controlled buckling produces a light weight concentrator and adjustments in the compression of individual strips provide a means of compensating for temperature excursions or changing the focal pattern at will.

Characteristics of unstable resonators in flashlamp-pumped organic-compound lasers

NASA Astrophysics Data System (ADS)

Alekseyev, V. A.; Trinchuk, B. F.; Shulenin, A. V.

1985-01-01

A symmetrical confocal resonator formed by two blind convex mirrors was investigated. The space energy characteristics of radiation from a laser with an unstable resonator were investigated as a function of the specific pumping energy per cubic centimeter of active medium and the magnification of the resonator. Oscillograms of laser pulses were recorded in different cross sections of the laser beam, as were the lasing field patterns at various distances from the exit mirror of the resonator. The maximum spectral wavelengths of flat and unstable resonators were tabulated. It was found that the proper choice of parameters of an unstable resonator reduces laser beam divergence significantly and provides greater axial brightness of radiation than that provided by a flat resonator, even with a highly nonhomogeneous active medium, making it possible to extend the capabilities of flashlamp pumped organic compound lasers.

Mating patterns and post-mating isolation in three cryptic species of the Engystomops petersi species complex

PubMed Central

Narvaez, Andrea E.; Ron, Santiago R.; Hoke, Kim L.

2017-01-01

Determining the extent of reproductive isolation in cryptic species with dynamic geographic ranges can yield important insights into the processes that generate and maintain genetic divergence in the absence of severe geographic barriers. We studied mating patterns, propensity to hybridize in nature and subsequent fertilization rates, as well as survival and development of hybrid F1 offspring for three nominal species of the Engystomops petersi species complex in Yasuní National Park, Ecuador. We found at least two species in four out of six locations sampled, and 14.3% of the wild pairs genotyped were mixed-species (heterospecific) crosses. We also found reduced fertilization rates in hybrid crosses between E. petersi females and E. “magnus” males, and between E. “magnus” females and E. “selva” males but not in the reciprocal crosses, suggesting asymmetric reproductive isolation for these species. Larval development times decreased in F1 hybrid crosses compared to same species (conspecific) crosses, but we did not find significant reduction in larval survival or early metamorph survival. Our results show evidence of post-mating isolation for at least two hybrid crosses of the cryptic species we studied. The general decrease in fertilization rates in heterospecific crosses suggests that sexual selection and reinforcement might have not only contributed to the pattern of call variation and behavioral isolation we see between species today, but they may also contribute to further signal divergence and behavioral evolution, especially in locations where hybridization is common and fertilization success is diminished. PMID:28388628

Elastic and inelastic neutron scattering cross sections for fission reactor applications

NASA Astrophysics Data System (ADS)

Hicks, S. F.; Chakraborty, A.; Combs, B.; Crider, B. P.; Downes, L.; Girgis, J.; Kersting, L. J.; Kumar, A.; Lueck, C. J.; McDonough, P. J.; McEllistrem, M. T.; Peters, E. E.; Prados-Estevz, F. M.; Schniederjan, J.; Sidwell, L.; Sigillito, A. J.; Vanhoy, J. R.; Watts, D.; Yates, S. W.

2013-04-01

Nuclear data important for the design and development of the next generation of light-water reactors and future fast reactors include neutron elastic and inelastic scattering cross sections on important structural materials, such as Fe, and on coolant materials, such as Na. These reaction probabilities are needed since neutron reactions impact fuel performance during irradiations and the overall efficiency of reactors. While neutron scattering cross sections from these materials are available for certain incident neutron energies, the fast neutron region, particularly above 2 MeV, has large gaps for which no measurements exist, or the existing uncertainties are large. Measurements have been made at the University of Kentucky Accelerator Laboratory to measure neutron scattering cross sections on both Fe and Na in the region where these gaps occur and to reduce the uncertainties on scattering from the ground state and first excited state of these nuclei. Results from measurements on Fe at incident neutron energies between 2 and 4 MeV will be presented and comparisons will be made to model calculations available from data evaluators.

MINERvA Measurement of Neutrino Charged-Current Cross Section Ratios of Nuclei C, Fe, and Pb to CH at Energies of a Few GeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gran, Richard

2016-06-02

The MINERvA experiment is designed to measure neutrino cross sections for different nuclei using substantially similar fiducial and tracking environments. This allows for reduced systematics in the ratio to better see the evolution of the cross section with the size of the nucleus. The first such result is an inclusive charged current cross section ratio as a function of energy from and the kinematic quantity Bjorken x for nuclei Pb, Fe, and C relative to plastic scintillator CH. The measurement is made for neutrino energies from 2 to 20 GeV. In the past, charged lepton scattering ratios of heavier nucleimore » to deuterium have revealed interesting structure such as the EMC effect. These ratios were restricted to purely deep inelastic scattering data whereas these ratios to different nuclei in MINERvA are sensitive to the elastic scattering as well as resonance production regions. Significant deviations from the baseline scattering model are observed, and suggest new theory work to investigate these ratios.« less

Hydrogen and Nitrogen Broadened Ethane and Propane Absorption Cross Sections

NASA Astrophysics Data System (ADS)

Hargreaves, Robert J.; Appadoo, Dominique; Billinghurst, Brant E.; Bernath, Peter F.

2015-06-01

High-resolution infrared absorption cross sections are presented for the ν9 band of ethane (C2H6) at 823 cm-1. These cross sections make use of spectra recorded at the Australian Synchrotron using a Fourier transform infrared spectrometer with maximum resolution of 0.00096 cm-1. The spectra have been recorded at 150, 120 and 90 K for hydrogen and nitrogen broadened C2H6. They cover appropriate temperatures, pressures and broadening gases associated with the atmospheres of the Outer Planets and Titan, and will improve atmospheric retrievals. The THz/Far-IR beamline at the Australian Synchrotron is unique in combining a high-resolution Fourier transform spectrometer with an 'enclosive flow cooling' (EFC) cell designed to study molecules at low temperatures. The EFC cell is advantageous at temperatures for which the vapor pressure is very low, such as C2H6 at 90 K. Hydrogen broadened absorption cross sections of propane between 700 and 1200 cm-1 will also be presented based on spectra obtained at the Canadian Light Source.

Analysis of a Chevron Beam Thermal Actuator

NASA Astrophysics Data System (ADS)

Joshi, Amey Sanjay; Mohammed, Hussain; Kulkarni, S. M., Dr.

2018-02-01

Thermal MEMS (Micro-Electro-Mechanical Systems) actuators and sensors have a wide range of applications. The chevron type thermal actuators comparatively show superior performance over other existing electrostatic and thermal actuators. This paper describes the design and analysis of chevron type thermal actuator. Here standard design of Chevron type thermal actuator is considered which comprises of proof mass at center and array of six beams of a uniform cross section of 3 3 microns and an initial angle of 5°. The thermal actuator was designed and analyzed using analytical and finite element method and the results were compared. The model was also analyzed for initial angles of 2.5° and 7.5°, and the results were compared with FEA model. The cross section of the beam was varied and the finite element analysis of all three models was compared to suggest the best suitable thermal actuator structure.

Rational design of capillary-driven flows for paper-based microfluidics.

PubMed

Elizalde, Emanuel; Urteaga, Raúl; Berli, Claudio L A

2015-05-21

The design of paper-based assays that integrate passive pumping requires a precise programming of the fluid transport, which has to be encoded in the geometrical shape of the substrate. This requirement becomes critical in multiple-step processes, where fluid handling must be accurate and reproducible for each operation. The present work theoretically investigates the capillary imbibition in paper-like substrates to better understand fluid transport in terms of the macroscopic geometry of the flow domain. A fluid dynamic model was derived for homogeneous porous substrates with arbitrary cross-sectional shapes, which allows one to determine the cross-sectional profile required for a prescribed fluid velocity or mass transport rate. An extension of the model to slit microchannels is also demonstrated. Calculations were validated by experiments with prototypes fabricated in our lab. The proposed method constitutes a valuable tool for the rational design of paper-based assays.

Scientific visualization of volumetric radar cross section data

NASA Astrophysics Data System (ADS)

Wojszynski, Thomas G.

1992-12-01

For aircraft design and mission planning, designers, threat analysts, mission planners, and pilots require a Radar Cross Section (RCS) central tendency with its associated distribution about a specified aspect and its relation to a known threat, Historically, RCS data sets have been statically analyzed to evaluate a d profile. However, Scientific Visualization, the application of computer graphics techniques to produce pictures of complex physical phenomena appears to be a more promising tool to interpret this data. This work describes data reduction techniques and a surface rendering algorithm to construct and display a complex polyhedron from adjacent contours of RCS data. Data reduction is accomplished by sectorizing the data and characterizing the statistical properties of the data. Color, lighting, and orientation cues are added to complete the visualization system. The tool may be useful for synthesis, design, and analysis of complex, low observable air vehicles.

AlignMiner: a Web-based tool for detection of divergent regions in multiple sequence alignments of conserved sequences

PubMed Central

2010-01-01

Background Multiple sequence alignments are used to study gene or protein function, phylogenetic relations, genome evolution hypotheses and even gene polymorphisms. Virtually without exception, all available tools focus on conserved segments or residues. Small divergent regions, however, are biologically important for specific quantitative polymerase chain reaction, genotyping, molecular markers and preparation of specific antibodies, and yet have received little attention. As a consequence, they must be selected empirically by the researcher. AlignMiner has been developed to fill this gap in bioinformatic analyses. Results AlignMiner is a Web-based application for detection of conserved and divergent regions in alignments of conserved sequences, focusing particularly on divergence. It accepts alignments (protein or nucleic acid) obtained using any of a variety of algorithms, which does not appear to have a significant impact on the final results. AlignMiner uses different scoring methods for assessing conserved/divergent regions, Entropy being the method that provides the highest number of regions with the greatest length, and Weighted being the most restrictive. Conserved/divergent regions can be generated either with respect to the consensus sequence or to one master sequence. The resulting data are presented in a graphical interface developed in AJAX, which provides remarkable user interaction capabilities. Users do not need to wait until execution is complete and can.even inspect their results on a different computer. Data can be downloaded onto a user disk, in standard formats. In silico and experimental proof-of-concept cases have shown that AlignMiner can be successfully used to designing specific polymerase chain reaction primers as well as potential epitopes for antibodies. Primer design is assisted by a module that deploys several oligonucleotide parameters for designing primers "on the fly". Conclusions AlignMiner can be used to reliably detect divergent regions via several scoring methods that provide different levels of selectivity. Its predictions have been verified by experimental means. Hence, it is expected that its usage will save researchers' time and ensure an objective selection of the best-possible divergent region when closely related sequences are analysed. AlignMiner is freely available at http://www.scbi.uma.es/alignminer. PMID:20525162

Perceptions of Barriers to Effective Obesity Care: Results from the National ACTION Study.

PubMed

Kaplan, Lee M; Golden, Angela; Jinnett, Kimberly; Kolotkin, Ronette L; Kyle, Theodore K; Look, Michelle; Nadglowski, Joseph; O'Neil, Patrick M; Parry, Thomas; Tomaszewski, Kenneth J; Stevenin, Boris; Lilleøre, Søren Kruse; Dhurandhar, Nikhil V

2018-01-01

ACTION (Awareness, Care, and Treatment in Obesity maNagement) examined obesity-related perceptions, attitudes, and behaviors among people with obesity (PwO), health care providers (HCPs), and employer representatives (ERs). A total of 3,008 adult PwO (BMI ≥ 30 by self-reported height and weight), 606 HCPs, and 153 ERs completed surveys in a cross-sectional design. Despite several weight loss (WL) attempts, only 23% of PwO reported 10% WL during the previous 3 years. Many PwO (65%) recognized obesity as a disease, but only 54% worried their weight may affect future health. Most PwO (82%) felt "completely" responsible for WL; 72% of HCPs felt responsible for contributing to WL efforts; few ERs (18%) felt even partially responsible. Only 50% of PwO saw themselves as "obese," and 55% reported receiving a formal diagnosis of obesity. Despite HCPs' reported comfort with weight-related conversations, time constraints deprioritized these efforts. Only 24% of PwO had a scheduled follow-up to initial weight-related conversations. Few PwO (17%) perceived employer-sponsored wellness offerings as helpful in supporting WL. Although generally perceived as a disease, obesity is not commonly treated as such. Divergence in perceptions and attitudes potentially hinders better management. This study highlights inconsistent understanding of the impact of obesity and need for both self-directed and medical management. © 2017 The Obesity Society.

Nozzle Aerodynamic Stability During a Throat Shift

NASA Technical Reports Server (NTRS)

Kawecki, Edwin J.; Ribeiro, Gregg L.

2005-01-01

An experimental investigation was conducted on the internal aerodynamic stability of a family of two-dimensional (2-D) High Speed Civil Transport (HSCT) nozzle concepts. These nozzles function during takeoff as mixer-ejectors to meet acoustic requirements, and then convert to conventional high-performance convergent-divergent (CD) nozzles at cruise. The transition between takeoff mode and cruise mode results in the aerodynamic throat and the minimum cross-sectional area that controls the engine backpressure shifting location within the nozzle. The stability and steadiness of the nozzle aerodynamics during this so called throat shift process can directly affect the engine aerodynamic stability, and the mechanical design of the nozzle. The objective of the study was to determine if pressure spikes or other perturbations occurred during the throat shift process and, if so, identify the caused mechanisms for the perturbations. The two nozzle concepts modeled in the test program were the fixed chute (FC) and downstream mixer (DSM). These 2-D nozzles differ principally in that the FC has a large over-area between the forward throat and aft throat locations, while the DSM has an over-area of only about 10 percent. The conclusions were that engine mass flow and backpressure can be held constant simultaneously during nozzle throat shifts on this class of nozzles, and mode shifts can be accomplished at a constant mass flow and engine backpressure without upstream pressure perturbations.

Genome structure and emerging evidence of an incipient sex chromosome in Populus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yin, Tongming; DiFazio, Stephen P; Gunter, Lee E

The genus Populus consists of dioecious woody species with largely unknown genetic mechanisms for gender determination. We have discovered genetic and genomic features in the peritelomeric region of chromosome XIX that suggest this region of the Populus genome is in the process of developing characteristics of a sex chromosome. We have identified a gender-associated locus that consistently maps to this region. Furthermore, comparison of genetic maps across multiple Populus families reveals consistently distorted segregation within this region. We have intensively characterized this region using an F1 interspecific cross involving the female genotype that was used for genome sequencing. This regionmore » shows suppressed recombination and high divergence between the alternate haplotypes, as revealed by dense map-based genome assembly using microsatellite markers. The suppressed recombination, distorted segregation, and haplotype divergence were observed only for the maternal parent in this cross. Furthermore, the progeny of this cross showed a strongly male-biased sex ratio, in agreement with Haldane's rule that postulates that the heterogametic sex is more likely to be absent, rare, or sterile in interspecific crosses. Together, these results support the role of chromosome XIX in sex determination and suggest that sex determination in Populus occurs through a ZW system in which the female is the heterogametic gender.« less

Curriculum History, Schooling and the History of the Present

ERIC Educational Resources Information Center

Popkewitz, Thomas S.

2011-01-01

The essay focuses on curriculum history as the study of systems of reason. The first section considers curriculum as "converting ordinances", inscribing Puritan notions of education as evangelizing and calculating designs in American Progressive education. The second section examines the Social Question, a cross-Atlantic Protestant reformist…

Cognitive Development in Children with Brain Damage.

ERIC Educational Resources Information Center

Bortner, Morton

Presented is a report on a cross-sectional and longitudinal study concerned with the course of intellectual development in 210 children (6-12 years old) educationally designated as brain damaged (learning disabled and/or behavior problems) and assigned to special school placement. The report is divided into four sections which focus on…

A formalism for the systematic treatment of rapidity logarithms in Quantum Field Theory

NASA Astrophysics Data System (ADS)

Chiu, Jui-Yu; Jain, Ambar; Neill, Duff; Rothstein, Ira Z.

2012-05-01

Many observables in QCD rely upon the resummation of perturbation theory to retain predictive power. Resummation follows after one factorizes the cross section into the relevant modes. The class of observables which are sensitive to soft recoil effects are particularly challenging to factorize and resum since they involve rapidity logarithms. Such observables include: transverse momentum distributions at p T much less then the high energy scattering scale, jet broadening, exclusive hadroproduction and decay, as well as the Sudakov form factor. In this paper we will present a formalism which allows one to factorize and resum the perturbative series for such observables in a systematic fashion through the notion of a "rapidity renormalization group". That is, a Collin-Soper like equation is realized as a renormalization group equation, but has a more universal applicability to observables beyond the traditional transverse momentum dependent parton distribution functions (TMDPDFs) and the Sudakov form factor. This formalism has the feature that it allows one to track the (non-standard) scheme dependence which is inherent in any sce- nario where one performs a resummation of rapidity divergences. We present a pedagogical introduction to the formalism by applying it to the well-known massive Sudakov form fac- tor. The formalism is then used to study observables of current interest. A factorization theorem for the transverse momentum distribution of Higgs production is presented along with the result for the resummed cross section at NLL. Our formalism allows one to define gauge invariant TMDPDFs which are independent of both the hard scattering amplitude and the soft function, i.e. they are universal. We present details of the factorization and re- summation of the jet broadening cross section including a renormalization in p ⊥ space. We furthermore show how to regulate and renormalize exclusive processes which are plagued by endpoint singularities in such a way as to allow for a consistent resummation.

KINKFOLD—an AutoLISP program for construction of geological cross-sections using borehole image data

NASA Astrophysics Data System (ADS)

Özkaya, Sait Ismail

2002-04-01

KINKFOLD is an AutoLISP program designed to construct geological cross-sections from borehole image or dip meter logs. The program uses the kink-fold method for cross-section construction. Beds are folded around hinge lines as angle bisectors so that bedding thickness remains unchanged. KINKFOLD may be used to model a wide variety of parallel fold structures, including overturned and faulted folds, and folds truncated by unconformities. The program accepts data from vertical or inclined boreholes. The KINKFOLD program cannot be used to model fault drag, growth folds, inversion structures or disharmonic folds where the bed thickness changes either because of deformation or deposition. Faulted structures and similar folds can be modelled by KINKFOLD by omitting dip measurements within fault drag zones and near axial planes of similar folds.

Computer codes for checking, plotting and processing of neutron cross-section covariance data and their application

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sartori, E.; Roussin, R.W.

This paper presents a brief review of computer codes concerned with checking, plotting, processing and using of covariances of neutron cross-section data. It concentrates on those available from the computer code information centers of the United States and the OECD/Nuclear Energy Agency. Emphasis will be placed also on codes using covariances for specific applications such as uncertainty analysis, data adjustment and data consistency analysis. Recent evaluations contain neutron cross section covariance information for all isotopes of major importance for technological applications of nuclear energy. It is therefore important that the available software tools needed for taking advantage of this informationmore » are widely known as hey permit the determination of better safety margins and allow the optimization of more economic, I designs of nuclear energy systems.« less

Distinct development of peripheral trigeminal pathways in the platypus (Ornithorhynchus anatinus) and short-beaked echidna (Tachyglossus aculeatus).

PubMed

Ashwell, Ken W S; Hardman, Craig D; Giere, Peter

2012-01-01

The extant monotremes (platypus and echidnas) are believed to all be capable of electroreception in the trigeminal pathways, although they differ significantly in the number and distribution of electroreceptors. It has been argued by some authors that electroreception was first developed in an aquatic environment and that echidnas are descended from a platypus-like ancestor that invaded an available terrestrial habitat. If this were the case, one would expect the developmental trajectories of the trigeminal pathways to be similar in the early stages of platypus and short-beaked echidna development, with structural divergence occurring later. We examined the development of the peripheral trigeminal pathway from snout skin to trigeminal ganglion in sectioned material in the Hill and Hubrecht collections to test for similarities and differences between the two during the development from egg to adulthood. Each monotreme showed a characteristic and different pattern of distribution of developing epidermal sensory gland specializations (electroreceptor primordia) from the time of hatching. The cross-sectional areas of the trigeminal divisions and the volume of the trigeminal ganglion itself were also very different between the two species at embryonic ages, and remained consistently different throughout post-hatching development. Our findings indicate that the trigeminal pathways in the short-beaked echidna and the platypus follow very different developmental trajectories from the earliest ages. These findings are more consistent with the notion that the platypus and echidna have both diverged from an ancestor with rudimentary electroreception and/or trigeminal specialization, rather than the contention that the echidna is derived from a platypus-like ancestor. Copyright © 2011 S. Karger AG, Basel.

Misregulation of spermatogenesis genes in Drosophila hybrids is lineage-specific and driven by the combined effects of sterility and fast male regulatory divergence.

PubMed

Gomes, S; Civetta, A

2014-09-01

Hybrid male sterility is a common outcome of crosses between different species. Gene expression studies have found that a number of spermatogenesis genes are differentially expressed in sterile hybrid males, compared with parental species. Late-stage sperm development genes are particularly likely to be misexpressed, with fewer early-stage genes affected. Thus, a link has been posited between misexpression and sterility. A more recent alternative explanation for hybrid gene misexpression has been that it is independent of sterility and driven by divergent evolution of male-specific regulatory elements between species (faster male hypothesis). The faster male hypothesis predicts that misregulation of spermatogenesis genes should be independent of sterility and approximately the same in both hybrids, whereas sterility should only affect gene expression in sterile hybrids. To test the faster male hypothesis vs. the effect of sterility on gene misexpression, we analyse spermatogenesis gene expression in different species pairs of the Drosophila phylogeny, where hybrid male sterility occurs in only one direction of the interspecies cross (i.e. unidirectional sterility). We find significant differences among genes in misexpression with effects that are lineage-specific and caused by sterility or fast male regulatory divergence. © 2014 The Authors. Journal of Evolutionary Biology © 2014 European Society For Evolutionary Biology.

Rapid evolution of reproductive isolation between incipient outcrossing and selfing Clarkia species.

PubMed

Briscoe Runquist, Ryan D; Chu, Eric; Iverson, Justin L; Kopp, Jason C; Moeller, David A

2014-10-01

A major goal of speciation research is to understand the processes involved in the earliest stages of the evolution of reproductive isolation (RI). One important challenge has been to identify systems where lineages have very recently diverged and opportunities for hybridization are present. We conducted a comprehensive examination of the components of RI across the life cycle of two subspecies of Clarkia xantiana, which diverged recently (ca. 65,000 bp). One subspecies is primarily outcrossing, but self-compatible, whereas the other is primarily selfing. The subspecies co-occur in a zone of sympatry but hybrids are rarely observed. Premating barriers resulted in nearly complete isolation in both subspecies with flowering time and pollinator preference (for the outcrosser over the selfer) as the strongest barriers. We found that the outcrosser had consistently more competitive pollen, facilitating hybridization in one direction, but no evidence for pollen-pistil interactions as an isolating barrier. Surprisingly, postzygotic isolation was detected at the stage of hybrid seed development, but in no subsequent life stages. This crossing barrier was asymmetric with crosses from the selfer to outcrosser most frequently failing. Collectively, the results provide evidence for rapid evolution of multiple premating and postzygotic barriers despite a very recent divergence time. © 2014 The Author(s). Evolution © 2014 The Society for the Study of Evolution.

Analyzing the relationship between sequence divergence and nodal support using Bayesian phylogenetic analyses.

PubMed

Makowsky, Robert; Cox, Christian L; Roelke, Corey; Chippindale, Paul T

2010-11-01

Determining the appropriate gene for phylogeny reconstruction can be a difficult process. Rapidly evolving genes tend to resolve recent relationships, but suffer from alignment issues and increased homoplasy among distantly related species. Conversely, slowly evolving genes generally perform best for deeper relationships, but lack sufficient variation to resolve recent relationships. We determine the relationship between sequence divergence and Bayesian phylogenetic reconstruction ability using both natural and simulated datasets. The natural data are based on 28 well-supported relationships within the subphylum Vertebrata. Sequences of 12 genes were acquired and Bayesian analyses were used to determine phylogenetic support for correct relationships. Simulated datasets were designed to determine whether an optimal range of sequence divergence exists across extreme phylogenetic conditions. Across all genes we found that an optimal range of divergence for resolving the correct relationships does exist, although this level of divergence expectedly depends on the distance metric. Simulated datasets show that an optimal range of sequence divergence exists across diverse topologies and models of evolution. We determine that a simple to measure property of genetic sequences (genetic distance) is related to phylogenic reconstruction ability in Bayesian analyses. This information should be useful for selecting the most informative gene to resolve any relationships, especially those that are difficult to resolve, as well as minimizing both cost and confounding information during project design. Copyright © 2010. Published by Elsevier Inc.

Significant parent-of-origin effects in cucumber

USDA-ARS?s Scientific Manuscript database

Cucumber is a useful plant to study organellar effects because chloroplasts are maternally and mitochondria paternally transmitted. We produced doubled haploids (DH) from divergent cucumber populations, generated reciprocal crosses in a diallel mating scheme, measured weights of plants approximately...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Youinou, Gilles Jean-Michel

Neutron cross-sections characterize the way neutrons interact with matter. They are essential to most nuclear engineering projects and, even though theoretical progress has been made as far as the predictability of neutron cross-section models, measurements are still indispensable to meet tight design requirements for reduced uncertainties. Within the field of fission reactor technology, one can identify the following specializations that rely on the availability of accurate neutron cross-sections: (1) fission reactor design, (2) nuclear fuel cycles, (3) nuclear safety, (4) nuclear safeguards, (5) reactor monitoring and neutron fluence determination and (6) waste disposal and transmutation. In particular, the assessment ofmore » advanced fuel cycles requires an extensive knowledge of transuranics cross sections. Plutonium isotopes, but also americium, curium and up to californium isotope data are required with a small uncertainty in order to optimize significant features of the fuel cycle that have an impact on feasibility studies (e.g. neutron doses at fuel fabrication, decay heat in a repository, etc.). Different techniques are available to determine neutron cross sections experimentally, with the common denominator that a source of neutrons is necessary. It can either come from an accelerator that produces neutrons as a result of interactions between charged particles and a target, or it can come from a nuclear reactor. When the measurements are performed with an accelerator, they are referred to as differential since the analysis of the data provides the cross-sections for different discrete energies, i.e. σ(E i), and for the diffusion cross sections for different discrete angles. Another approach is to irradiate a very pure sample in a test reactor such as the Advanced Test Reactor (ATR) at INL and, after a given time, determine the amount of the different transmutation products. The precise characterization of the nuclide densities before and after neutron irradiation allows to infer energy-integrated neutron cross sections, i.e. ∫₀ ∞σ(E)φ(E)dE, where φ(E) is the neutron flux “seen” by the sample. This approach, which is usually defined and led by reactor physicists, is referred to as integral and is the object of this report. These two sources of information, i.e. differential and integral, are complementary and are used by the nuclear physicists in charge of producing the evaluated nuclear data files used by the nuclear community (ENDF, JEFF…). The generation of accurate nuclear data files requires an iterative process involving reactor physicists and nuclear data evaluators. This experimental program has been funded by the ATR National Scientific User Facility (ATR-NSUF) and by the DOE Office of Science in the framework of the Recovery Act. It has been given the name MANTRA for Measurement of Actinides Neutron TRAnsmutation.« less

A Comparison of Combustion Dynamics for Multiple 7-Point Lean Direct Injection Combustor Configurations

NASA Technical Reports Server (NTRS)

Tacina, K. M.; Hicks, Y. R.

2017-01-01

The combustion dynamics of multiple 7-point lean direct injection (LDI) combustor configurations are compared. LDI is a fuel-lean combustor concept for aero gas turbine engines in which multiple small fuel-air mixers replace one traditionally-sized fuel-air mixer. This 7-point LDI configuration has a circular cross section, with a center (pilot) fuel-air mixer surrounded by six outer (main) fuel-air mixers. Each fuel-air mixer consists of an axial air swirler followed by a converging-diverging venturi. A simplex fuel injector is inserted through the center of the air swirler, with the fuel injector tip located near the venturi throat. All 7 fuel-air mixers are identical except for the swirler blade angle, which varies with the configuration. Testing was done in a 5-atm flame tube with inlet air temperatures from 600 to 800 F and equivalence ratios from 0.4 to 0.7. Combustion dynamics were measured using a cooled PCB pressure transducer flush-mounted in the wall of the combustor test section.

Progress of the Charged Pion Semi-Inclusive Neutrino Charged Current Cross Section in NOvA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsaris, Aristeidis

2017-10-09

The NOvA experiment is a long-baseline neutrino oscillation experiment designed to measure the rates of electron neutrino appearance and muon neutrino disappearance. The NOvA near detector is located at Fermilab, 800 m from the primary target and provides an excellent platform to measure and study neutrino-nucleus interactions. We present the status of the measurement of the double differential cross section with respect to muon kinematics for interactions involving charged pions in the final state,more » $$\

Thermal performance of plate fin heat sink cooled by air slot impinging jet with different cross-sectional area

NASA Astrophysics Data System (ADS)

Mesalhy, O. M.; El-Sayed, Mostafa M.

2015-06-01

Flow and heat transfer characteristics of a plate-fin heat sink cooled by a rectangular impinging jet with different cross-sectional area were studied experimentally and numerically. The study concentrated on investigating the effect of jet width, fin numbers, and fin heights on thermal performance. Entropy generation minimization method was used to define the optimum design and operating conditions. It is found that, the jet width that minimizes entropy generation changes with heat sink height and fin numbers.

Minerva Detector Calibration

NASA Astrophysics Data System (ADS)

Rakotondravohitra, Laza

2013-04-01

Current and future neutrino oscillation experiments depend on precise knowledge of neutrino-nucleus cross-sections. Minerva is a neutrino scattering experiment at Fermilab. Minerva was designed to make precision measurements of low energy neutrino and antineutrino cross sections on a variety of different materials (plastic scintillator, C, Fe, Pb, He and H2O). In Order to make these measurements, it is crucial that the detector is carefully calibrated.This talk will describe how MINERvA uses muons from upstream neutrino interactions as a calibration source to convert electronics output to absolute energy deposition.

Antioxidant state and mortality from coronary heart disease in Lithuanian and Swedish men: concomitant cross sectional study of men aged 50.

PubMed Central

Kristenson, M.; Ziedén, B.; Kucinskienë, Z.; Elinder, L. S.; Bergdahl, B.; Elwing, B.; Abaravicius, A.; Razinkovienë, L.; Calkauskas, H.; Olsson, A. G.

1997-01-01

OBJECTIVE: To investigate possible risk factors and mechanisms behind the four times higher and diverging mortality from coronary heart disease in Lithuanian compared with Swedish middle aged men. DESIGN: Concomitant cross sectional comparison of randomly selected 50 year old men without serious acute or chronic disease. Methods and equipment were identical or highly standardised between the centres. SETTING: Linköping (Sweden) and Vilnius (Lithuania). SUBJECTS: 101 and 109 men aged 50 in Linköping and Vilnius respectively. MAIN OUTCOME MEASURES: Anthropometric data, blood pressure, smoking, plasma lipid and lipoprotein concentrations, susceptibility of low density lipoprotein to oxidation, and plasma concentrations of fat soluble antioxidant vitamins. RESULTS: Systolic blood pressure was higher (141 v 133 mm Hg, P < 0.01), smoking habits were similar, and plasma total cholesterol (5.10 v 5.49 mmol/l, P < 0.01) and low density lipoprotein cholesterol (3.30 v 3.68 mmol/l, P < 0.01) lower in men from Vilnius compared with those from Linköping. Triglyceride, high density lipoprotein cholesterol, and Lp(a) lipoprotein concentrations did not differ between the two groups. The resistance of low density lipoprotein to oxidation was lower in the men from Vilnius; lag phase was 67.6 v 79.5 minutes (P < 0.001). Also lower in the men from Vilnius were mean plasma concentrations of lipid soluble antioxidant vitamins (beta carotene 377 v 510 nmol/l, P < 0.01; lycopene 327 v 615 nmol/l, P < 0.001; and lipid adjusted gamma tocopherol 0.25 v 0.46 mumol/mmol, P < 0.001. alpha Tocopherol concentration did not differ). Regression analysis showed that the lag phase was still significantly shorter by 10 minutes in men from Vilnius when the influence of other known factors was taken into account. CONCLUSIONS: The high mortality from coronary heart disease in Lithuania is not caused by traditional risk factors alone. Mechanisms related to antioxidant state may be important. PMID:9066473

33 CFR 332.4 - Planning and documentation.

Code of Federal Regulations, 2010 CFR

2010-07-01

....g., typical channel cross-sections), watershed size, design discharge, and riparian area plantings... achieved to ensure the long-term sustainability of the resource, including long-term financing mechanisms...

Study of an advanced transport airplane design concept known as Flatbed

NASA Technical Reports Server (NTRS)

Smethers, R. G.; Caldwell, E. W.; Warnock, W. E.; Wilson, J. M., Jr.

1980-01-01

The design concept and configuration of the Flatbed transport aircraft are presented. The Flatbed configuration combines into one frame, the ability to haul cargo, virtually unrestrained by cross sectional dimensions of the fuselage. The feasibility and capability of the Flatbed is discussed in depth.

Aerosol and Cloud Observations and Data Products by the GLAS Polar Orbiting Lidar Instrument

NASA Technical Reports Server (NTRS)

Spinhirne, J. D.; Palm, S. P.; Hlavka, D. L.; Hart, W. D.; Mahesh, A.; Welton, E. J.

2005-01-01

The Geoscience Laser Altimeter System (GLAS) launched in 2003 is the first polar orbiting satellite lidar. The instrument was designed for high performance observations of the distribution and optical scattering cross sections of clouds and aerosol. The backscatter lidar operates at two wavelengths, 532 and 1064 nm. Both receiver channels meet and exceed their design goals, and beginning with a two month period through October and November 2003, an excellent global lidar data set now exists. The data products for atmospheric observations include the calibrated, attenuated backscatter cross section for cloud and aerosol; height detection for multiple cloud layers; planetary boundary layer height; cirrus and aerosol optical depth and the height distribution of aerosol and cloud scattering cross section profiles. The data sets are now in open release through the NASA data distribution system. The initial results on global statistics for cloud and aerosol distribution has been produced and in some cases compared to other satellite observations. The sensitivity of the cloud measurements is such that the 70% global cloud coverage result should be the most accurate to date. Results on the global distribution of aerosol are the first that produce the true height distribution for model inter-comparison.

HZETRN: Description of a free-space ion and nucleon transport and shielding computer program

NASA Technical Reports Server (NTRS)

Wilson, John W.; Badavi, Francis F.; Cucinotta, Francis A.; Shinn, Judy L.; Badhwar, Gautam D.; Silberberg, R.; Tsao, C. H.; Townsend, Lawrence W.; Tripathi, Ram K.

1995-01-01

The high-charge-and energy (HZE) transport computer program HZETRN is developed to address the problems of free-space radiation transport and shielding. The HZETRN program is intended specifically for the design engineer who is interested in obtaining fast and accurate dosimetric information for the design and construction of space modules and devices. The program is based on a one-dimensional space-marching formulation of the Boltzmann transport equation with a straight-ahead approximation. The effect of the long-range Coulomb force and electron interaction is treated as a continuous slowing-down process. Atomic (electronic) stopping power coefficients with energies above a few A MeV are calculated by using Bethe's theory including Bragg's rule, Ziegler's shell corrections, and effective charge. Nuclear absorption cross sections are obtained from fits to quantum calculations and total cross sections are obtained with a Ramsauer formalism. Nuclear fragmentation cross sections are calculated with a semiempirical abrasion-ablation fragmentation model. The relation of the final computer code to the Boltzmann equation is discussed in the context of simplifying assumptions. A detailed description of the flow of the computer code, input requirements, sample output, and compatibility requirements for non-VAX platforms are provided.

Effects of eccentricities and lateral pressure on the design of stiffened compression panels

NASA Technical Reports Server (NTRS)

Giles, G. L.; Anderson, M. S.

1972-01-01

An analysis for determining the effects of eccentricities and lateral pressure on the design of stiffened compression panels is presented. The four types of panel stiffeners considered are integral, zee, integral zee, and integral tee. Mass-strength curves, which give the mass of the panel necessary to carry a specified load, are given along with related design equations needed to calculate the cross-sectional dimensions of the minimum-mass-stiffened panel. The results of the study indicate that the proportions of the panels are geometrically similar to the proportions of panels designed for no eccentricity or lateral pressure, but no cross-sectional dimensions are greater, resulting in significantly increased mass. The analytical minimum-mass designs of zee-stiffened panels are compared with designs from experimentally derived charts. An assumed eccentricity of 0.001 times the length of the panel is used to correlate the analytical and experimental data. Good correlation between the experimentally derived and the analytical curves is obtained for the range of loading where materials yield governs the design. At lower loads the mass given by the analytical curve using this assumed eccentricity is greater than that given by the experimental results.

Velocity-based analysis of sediment incipient deposition in rigid boundary open channels.

PubMed

Aksoy, Hafzullah; Safari, Mir Jafar Sadegh; Unal, Necati Erdem; Mohammadi, Mirali

2017-11-01

Drainage systems must be designed in a way to minimize undesired problems such as decrease in hydraulic capacity of the channel, blockage and transport of pollutants due to deposition of sediment. Channel design considering self-cleansing criteria are used to solve the sedimentation problem. Incipient deposition is one of the non-deposition self-cleansing design criteria that can be used as a conservative method for channel design. Experimental studies have been carried out in five different cross-section channels, namely trapezoidal, rectangular, circular, U-shape and V-bottom. Experiments were performed in a tilting flume using four different sizes of sands as sediment in nine different channel bed slopes. Two well-known methods, namely the Novak & Nalluri and Yang methods are considered for the analysis of sediment motion. Equations developed using experimental data are found to be in agreement with the literature. It is concluded that the design velocity depends on the shape of the channel cross-section. Rectangular and V-bottom channels need lower and higher incipient deposition velocities, respectively, in comparison with other channels.

Sample size calculations for stepped wedge and cluster randomised trials: a unified approach

PubMed Central

Hemming, Karla; Taljaard, Monica

2016-01-01

Objectives To clarify and illustrate sample size calculations for the cross-sectional stepped wedge cluster randomized trial (SW-CRT) and to present a simple approach for comparing the efficiencies of competing designs within a unified framework. Study Design and Setting We summarize design effects for the SW-CRT, the parallel cluster randomized trial (CRT), and the parallel cluster randomized trial with before and after observations (CRT-BA), assuming cross-sectional samples are selected over time. We present new formulas that enable trialists to determine the required cluster size for a given number of clusters. We illustrate by example how to implement the presented design effects and give practical guidance on the design of stepped wedge studies. Results For a fixed total cluster size, the choice of study design that provides the greatest power depends on the intracluster correlation coefficient (ICC) and the cluster size. When the ICC is small, the CRT tends to be more efficient; when the ICC is large, the SW-CRT tends to be more efficient and can serve as an alternative design when the CRT is an infeasible design. Conclusion Our unified approach allows trialists to easily compare the efficiencies of three competing designs to inform the decision about the most efficient design in a given scenario. PMID:26344808

Low cost and thin metasurface for ultra wide band and wide angle polarization insensitive radar cross section reduction

NASA Astrophysics Data System (ADS)

Ameri, Edris; Esmaeli, Seyed Hassan; Sedighy, Seyed Hassan

2018-05-01

A planar low cost and thin metasurface is proposed to achieve ultra-wideband radar cross section (RCS) reduction with stable performance with respect to polarization and incident angles. This metasurface is composed of two different artificial magnetic conductor unit cells arranged in a chessboard like configuration. These unit cells have a Jerusalem cross pattern with different thicknesses, which results in wideband out-phase reflection and RCS reduction, consequently. The designed metasurface reduces RCS more than 10-dB from 13.6 GHz to 45.5 GHz (108% bandwidth) and more than 20-dB RCS from 15.2 GHz to 43.6 GHz (96.6%). Moreover, the 10-dB RCS reduction bandwidth is very stable (more than 107%) for both TE and TM polarizations. The good agreement between simulations and measurement results proves the design, properly. The ultra-wide bandwidth, low cost, low profile, and stable performance of this metasurface prove its high capability compared with the state-of-the-art references.

Design concepts for pressurized lunar shelters utilizing indigenous materials

NASA Technical Reports Server (NTRS)

Happel, John Amin; Willam, Kaspar; Shing, Benson

1991-01-01

The objective is to design a pressurized shelter build of indigenous lunar material. The topics are presented in viewgraph form and include the following: lunar conditions which impact design; secondary factors; review of previously proposed concepts; cross section of assembly facility; rationale for indigenous materials; indigenous material choices; cast basalt properties; design variables; design 1, cylindrical segments; construction sequence; design 2, arch-slabs with post-tensioned ring girders; and future research.

Lineage-specific rediploidization is a mechanism to explain time-lags between genome duplication and evolutionary diversification.

PubMed

Robertson, Fiona M; Gundappa, Manu Kumar; Grammes, Fabian; Hvidsten, Torgeir R; Redmond, Anthony K; Lien, Sigbjørn; Martin, Samuel A M; Holland, Peter W H; Sandve, Simen R; Macqueen, Daniel J

2017-06-14

The functional divergence of duplicate genes (ohnologues) retained from whole genome duplication (WGD) is thought to promote evolutionary diversification. However, species radiation and phenotypic diversification are often temporally separated from WGD. Salmonid fish, whose ancestor underwent WGD by autotetraploidization ~95 million years ago, fit such a 'time-lag' model of post-WGD radiation, which occurred alongside a major delay in the rediploidization process. Here we propose a model, 'lineage-specific ohnologue resolution' (LORe), to address the consequences of delayed rediploidization. Under LORe, speciation precedes rediploidization, allowing independent ohnologue divergence in sister lineages sharing an ancestral WGD event. Using cross-species sequence capture, phylogenomics and genome-wide analyses of ohnologue expression divergence, we demonstrate the major impact of LORe on salmonid evolution. One-quarter of each salmonid genome, harbouring at least 4550 ohnologues, has evolved under LORe, with rediploidization and functional divergence occurring on multiple independent occasions >50 million years post-WGD. We demonstrate the existence and regulatory divergence of many LORe ohnologues with functions in lineage-specific physiological adaptations that potentially facilitated salmonid species radiation. We show that LORe ohnologues are enriched for different functions than 'older' ohnologues that began diverging in the salmonid ancestor. LORe has unappreciated significance as a nested component of post-WGD divergence that impacts the functional properties of genes, whilst providing ohnologues available solely for lineage-specific adaptation. Under LORe, which is predicted following many WGD events, the functional outcomes of WGD need not appear 'explosively', but can arise gradually over tens of millions of years, promoting lineage-specific diversification regimes under prevailing ecological pressures.

A meta-analysis on progressive atrophy in intractable temporal lobe epilepsy

PubMed Central

Caciagli, Lorenzo; Bernasconi, Andrea; Wiebe, Samuel; Koepp, Matthias J.; Bernasconi, Neda

2017-01-01

Objective: It remains unclear whether drug-resistant temporal lobe epilepsy (TLE) is associated with cumulative brain damage, with no expert consensus and no quantitative syntheses of the available evidence. Methods: We conducted a systematic review and meta-analysis of MRI studies on progressive atrophy, searching PubMed and Ovid MEDLINE databases for cross-sectional and longitudinal quantitative MRI studies on drug-resistant TLE. Results: We screened 2,976 records and assessed eligibility of 248 full-text articles. Forty-two articles met the inclusion criteria for quantitative evaluation. We observed a predominance of cross-sectional studies, use of different clinical indices of progression, and high heterogeneity in age-control procedures. Meta-analysis of 18/1 cross-sectional/longitudinal studies on hippocampal atrophy (n = 979 patients) yielded a pooled effect size of r = −0.42 for ipsilateral atrophy related to epilepsy duration (95% confidence interval [CI] −0.51 to −0.32; p < 0.0001; I2 = 65.22%) and r = −0.35 related to seizure frequency (95% CI −0.47 to −0.22; p < 0.0001; I2 = 61.97%). Sensitivity analyses did not change the results. Narrative synthesis of 25/3 cross-sectional/longitudinal studies on whole brain atrophy (n = 1,504 patients) indicated that >80% of articles reported duration-related progression in extratemporal cortical and subcortical regions. Detailed analysis of study design features yielded low to moderate levels of evidence for progressive atrophy across studies, mainly due to dominance of cross-sectional over longitudinal investigations, use of diverse measures of seizure estimates, and absence of consistent age control procedures. Conclusions: While the neuroimaging literature is overall suggestive of progressive atrophy in drug-resistant TLE, published studies have employed rather weak designs to directly demonstrate it. Longitudinal multicohort studies are needed to unequivocally differentiate aging from disease progression. PMID:28687722

Method and apparatus for jet-assisted drilling or cutting

DOEpatents

Summers, David Archibold; Woelk, Klaus Hubert; Oglesby, Kenneth Doyle; Galecki, Grzegorz

2012-09-04

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.

Method and apparatus for jet-assisted drilling or cutting

DOEpatents

Summers, David Archibold; Woelk, Klaus Hubert; Oglesby, Kenneth Doyle; Galecki, Grzegorz

2013-07-02

An abrasive cutting or drilling system, apparatus and method, which includes an upstream supercritical fluid and/or liquid carrier fluid, abrasive particles, a nozzle and a gaseous or low-density supercritical fluid exhaust abrasive stream. The nozzle includes a throat section and, optionally, a converging inlet section, a divergent discharge section, and a feed section.

Measuring Two Key Parameters of H3 Color Centers in Diamond

NASA Technical Reports Server (NTRS)

Roberts, W. Thomas

2005-01-01

A method of measuring two key parameters of H3 color centers in diamond has been created as part of a continuing effort to develop tunable, continuous-wave, visible lasers that would utilize diamond as the lasing medium. (An H3 color center in a diamond crystal lattice comprises two nitrogen atoms substituted for two carbon atoms bonded to a third carbon atom. H3 color centers can be induced artificially; they also occur naturally. If present in sufficient density, they impart a yellow hue.) The method may also be applicable to the corresponding parameters of other candidate lasing media. One of the parameters is the number density of color centers, which is needed for designing an efficient laser. The other parameter is an optical-absorption cross section, which, as explained below, is needed for determining the number density. The present method represents an improvement over prior methods in which optical-absorption measurements have been used to determine absorption cross sections or number densities. Heretofore, in order to determine a number density from such measurements, it has been necessary to know the applicable absorption cross section; alternatively, to determine the absorption cross section from such measurements, it has been necessary to know the number density. If, as in this case, both the number density and the absorption cross section are initially unknown, then it is impossible to determine either parameter in the absence of additional information.

Neutron elastic and inelastic cross section measurements for 28Si

NASA Astrophysics Data System (ADS)

Derdeyn, E. C.; Lyons, E. M.; Morin, T.; Hicks, S. F.; Vanhoy, J. R.; Peters, E. E.; Ramirez, A. P. D.; McEllistrem, M. T.; Mukhopadhyay, S.; Yates, S. W.

2017-09-01

Neutron elastic and inelastic cross sections are critical for design and implementation of nuclear reactors and reactor equipment. Silicon, an element used abundantly in fuel pellets as well as building materials, has little to no experimental cross sections in the fast neutron region to support current theoretical evaluations, and thus would benefit from any contribution. Measurements of neutron elastic and inelastic differential scattering cross sections for 28Si were performed at the University of Kentucky Accelerator Laboratory for incident neutron energies of 6.1 MeV and 7.0 MeV. Neutrons were produced by accelerated deuterons incident on a deuterium gas cell. These nearly mono-energetic neutrons then scattered off a natural Si sample and were detected using liquid deuterated benzene scintillation detectors. Scattered neutron energy was deduced using time-of-flight techniques in tandem with kinematic calculations for an angular distribution. The relative detector efficiency was experimentally determined over a neutron energy range from approximately 0.5 to 7.75 MeV prior to the experiment. Yields were corrected for multiple scattering and neutron attenuation in the sample using the forced-collision Monte Carlo correction code MULCAT. Resulting cross sections will be presented along with comparisons to various data evaluations. Research is supported by USDOE-NNSA-SSAP: NA0002931, NSF: PHY-1606890, and the Donald A. Cowan Physics Institute at the University of Dallas.

Performance of a transpiration-regenerative cooled rocket thrust chamber

NASA Technical Reports Server (NTRS)

Valler, H. W.

1979-01-01

The analysis, design, fabrication, and testing of a liquid rocket engine thrust chamber which is gas transpiration cooled in the high heat flux convergent portion of the chamber and water jacket cooled (simulated regenerative) in the barrel and divergent sections of the chamber are described. The engine burns LOX-hydrogen propellants at a chamber pressure of 600 psia. Various transpiration coolant flow rates were tested with resultant local hot gas wall temperatures in the 800 F to 1400 F range. The feasibility of transpiration cooling with hydrogen and helium, and the use of photo-etched copper platelets for heat transfer and coolant metering was successfully demonstrated.

Development of a high-energy distributed energy source electromagnetic railgun with improved energy conversion efficiency

NASA Astrophysics Data System (ADS)

Tower, M. M.; Haight, C. H.

1984-03-01

The development status of a single-pulse distributed-energy-source electromagnetic railgun (ER) based on the design of Tower (1982) is reviewed. The five-stage ER is 3.65 m long, with energy inputs every 30 cm starting at the breech and a 12.7-mm-square bore cross section, and is powered by a 660-kJ 6-kV modular capacitor bank. Lexan cubes weighing 2.5 grams have been accelerated to velocities up to 8.5 km/sec at 500 kA and conversion efficiency up to 20 percent. Design goal for a 20-mm-sq-cross-section ER is acceleration of a 60-g projectile to 3-4 km/sec at 35-percent efficiency. Drawings, photographs, and graphs of performance are provided.

Brain MRI volumetry in a single patient with mild traumatic brain injury.

PubMed

Ross, David E; Castelvecchi, Cody; Ochs, Alfred L

2013-01-01

This letter to the editor describes the case of a 42 year old man with mild traumatic brain injury and multiple neuropsychiatric symptoms which persisted for a few years after the injury. Initial CT scans and MRI scans of the brain showed no signs of atrophy. Brain volume was measured using NeuroQuant®, an FDA-approved, commercially available software method. Volumetric cross-sectional (one point in time) analysis also showed no atrophy. However, volumetric longitudinal (two points in time) analysis showed progressive atrophy in several brain regions. This case illustrated in a single patient the principle discovered in multiple previous group studies, namely that the longitudinal design is more powerful than the cross-sectional design for finding atrophy in patients with traumatic brain injury.

Speech-Language and Nutritional Sciences in hospital environment: analysis of terminology of food consistencies classification.

PubMed

Amaral, Ana Cláudia Fernandes; Rodrigues, Lívia Azevedo; Furlan, Renata Maria Moreira Moraes; Vicente, Laélia Cristina Caseiro; Motta, Andréa Rodrigues

2015-01-01

To verify if there is an agreement between speech-language pathologists and nutritionists about the classification of food textures used in hospitals and their opinions about the possible consequences of differences in this classification. This is a descriptive, cross-sectional study with 30 speech-language pathologists and 30 nutritionists who worked in 14 hospitals of public and/or private network in Belo Horizonte, Brazil. The professionals answered a questionnaire, prepared by the researchers, and classified five different foods, with and without theoretical direction. The data were analyzed using Fisher's exact and Z -tests to compare ratios with a 5% significance level. Both speech-language therapists (100%) and nutritionists (90%) perceive divergence in the classification and, 86.2% and 100% of them, respectively, believe that this difference may affect the patients' recovery. Aspiration risk was the most mentioned problem. For the general classification of food textures, most of the professionals (88.5%) suggested four to six terms. As to the terminology used in the classification of food presented without theoretical direction, the professionals cited 49 terms and agreed only in the solid and liquid classifications. With theoretical direction, the professionals also agreed in the classification of thick and thin paste. Both the professionals recognized divergences in the classification of food textures and the consequent risk of damage to patient's recovery. The use of theoretical direction increased the agreement between these professionals.

Unemployment and health selection in diverging economic conditions: Compositional changes? Evidence from 28 European countries.

PubMed

Heggebø, Kristian; Dahl, Espen

2015-11-04

Unemployment and health selection in diverging economic conditions: Compositional changes? Evidence from 28 european countries. People with ill health tend to be overrepresented among the unemployment population. The relationship between health and unemployment might, however, be sensitive to the overall economic condition. Specifically, the health composition of the unemployment population could change dramatically when the economy takes a turn for the worse. Using EU-SILC cross sectional data from 2007 (pre-crisis) and 2011 (during crisis) and linear regression models, this paper investigates the relationship between health and unemployment probabilities under differing economic conditions in 28 European countries. The countries are classified according to (i) the level of and (ii) increase in unemployment rate (i.e. >10 percent and doubling of unemployment rate = crisis country). Firstly, the unemployment likelihood for people with ill health is remarkably stable over time in Europe: the coefficients are very similar in pre-crisis and crisis years. Secondly, people with ill health have experienced unemployment to a lesser extent than those with good health status in the crisis year (when we pool the data and compare 2007 and 2011), but only in the countries with a high and rising unemployment rate. The health composition of the unemployment population changes significantly for the better, but only in those European countries that have been severely hit by the current economic crisis.

Functional morphology and biomechanics of the tongue-bite apparatus in salmonid and osteoglossomorph fishes

PubMed Central

Camp, Ariel L; Konow, Nicolai; Sanford, Christopher P J

2009-01-01

The tongue-bite apparatus and its associated musculoskeletal elements of the pectoral girdle and neurocranium form the structural basis of raking, a unique prey-processing behaviour in salmonid and osteoglossomorph fishes. Using a quantitative approach, the functional osteology and myology of this system were compared between representatives of each lineage, i.e. the salmonid Salvelinus fontinalis (N =10) and the osteoglossomorph Chitala ornata(N = 8). Divergence was found in the morphology of the novel cleithrobranchial ligament, which potentially relates to kinematic differences between the raking lineage representatives. Salvelinus had greater anatomical cross-sectional areas of the epaxial, hypaxial and protractor hyoideus muscles, whereas Chitala had greater sternohyoideus and adductor mandibulae mass. Two osteology-based biomechanical models (a third-order lever for neurocranial elevation and a modified four-bar linkage for hyoid retraction) showed divergent force/velocity priorities in the study taxa. Salvelinus maximizes both force (via powerful cranial muscles) and velocity (through mechanical amplification) during raking. In contrast, Chitala has relatively low muscle force but more efficient force transmission through both mechanisms compared with Salvelinus. It remains unclear if and how behavioural modulation and specializations in the post-cranial anatomy may affect the force/velocity trade-offs in Chitala. Further studies of tongue-bite apparatus morphology and biomechanics in a broader species range may help to clarify the role that osteology and myology play in the evolution of behavioural diversity. PMID:19438765

Alienation from School

ERIC Educational Resources Information Center

Hascher, Tina; Hagenauer, Gerda

2010-01-01

Two studies aimed at understanding the time course of alienation from school and school factors that may influence alienation from school during early adolescence. In Study 1, 434 students from grade 5-8 participated (cross-sectional design). In Study 2, we followed 356 students from grade 6-7 (longitudinal design). The results confirm the…

Predictors of Low-income, Obese Mothers' Use of Healthful Weight Management Behaviors

ERIC Educational Resources Information Center

Chang, Mei-Wei; Nitzke, Susan; Brown, Roger; Baumann, Linda

2011-01-01

Objective: To examine the influence of personal and environmental factors on healthful weight management behaviors mediated through self-efficacy among low-income obese mothers. Design: Cross-sectional design. Setting: Special Supplemental Nutrition Program for Women, Infants, and Children in Wisconsin. Participants: Two hundred eighty-four obese…

Association between Lifestyle and School Attendance in Japanese Medical Students: A Pilot Study

ERIC Educational Resources Information Center

Tanaka, Masaaki; Watanabe, Yasuyoshi

2012-01-01

Objective: Lifestyle factors are thought to be associated with students' academic performance. Whether lifestyle factors were associated with medical students' school attendance was determined. Design: Cross-sectional design. Setting: The study group consisted of 157 healthy second-year medical students attending Osaka City University Graduate…

Management of Communication Channels for Health Information in the Community

ERIC Educational Resources Information Center

Tanvatanakul, Vasuton; Amado, Joao; Saowakontha, Sastri

2007-01-01

Object: To investigate channels for communication of health information to various groups in the community. Design: An exploratory cross sectional design was used, followed by focus groups of selected participants to confirm and clarify the findings. Setting: Five levels of sub-district administration organizations were selected from different…

Knowledge about Sport and Exercise Science

ERIC Educational Resources Information Center

Leal, Acácia Gonçalves Ferreira; Vancini, Rodrigo Luiz; Gentil, Paulo; Benedito-Silva, Ana Amélia; da Silva, Antonio Carlos; Campos, Mário Hebling; Andrade, Marilia Santos; de Lira, Claudio Andre Barbosa

2018-01-01

Purpose: The purpose of this paper was to assess the knowledge on sport and exercise science held by a sample of Brazilian physiotherapists, nutritionists and physical educators. Design/methodology/approach: A cross-sectional research design was used. The answers given by 1,147 professionals (300 physiotherapists, 705 physical educators and 142…

Factors Influencing Residents' Satisfaction in Residential Aged Care

ERIC Educational Resources Information Center

Chou, Shu-Chiung; Boldy, Duncan P.; Lee, Andy H.

2003-01-01

Purpose: The aim of this study was to identify the important factors influencing residents' satisfaction in residential aged care and to provide a better understanding of their interrelationships. Design and Methods: A cross-sectional survey design was used to collect the required information, including resident satisfaction, resident dependency…

A Population-Based Study of Preschoolers' Food Neophobia and Its Associations with Food Preferences

ERIC Educational Resources Information Center

Russell, Catherine Georgina; Worsley, Anthony

2008-01-01

Objective: This cross-sectional study was designed to investigate the relationships between food preferences, food neophobia, and children's characteristics among a population-based sample of preschoolers. Design: A parent-report questionnaire. Setting: Child-care centers, kindergartens, playgroups, day nurseries, and swimming centers. Subjects:…

Knowledge Strategies for Enhancing School Learning Capacity

ERIC Educational Resources Information Center

Cheng, Eric

2012-01-01

Purpose: The purpose of this paper is to identify the knowledge strategies applied in aided secondary schools in Hong Kong and to explore the predictive relationship between knowledge strategies and school learning capacity. Design/methodology/approach: A cross-sectional quantitative survey was designed to collect data from 427 teachers at 15…

Supervisor Behaviours that Facilitate Training Transfer

ERIC Educational Resources Information Center

Lancaster, Sue; Di Milia, Lee; Cameron, Roslyn

2013-01-01

Purpose: The purpose of this paper is to describe the supervisor behaviours that employees found to be helpful and unhelpful in facilitating training transfer. The study aims to provide rich qualitative data from the employee's perspective. Design/methodology/approach: This study utilises a cross-sectional design. A case study and a qualitative…

Evaluation of pathogen-specific biomarkers for the diagnosis of tuberculosis in white-tailed deer (Odocoileus virginianus)

USDA-ARS?s Scientific Manuscript database

Objective - To develop a noninvasive biomarker based Mycobacterium bovis specific detection system to track infection in domestic and wild animals. Design – Experimental longitudinal study for discovery and cross sectional design for validation Animals - Yearling white-tailed deer fawns (n=8) were ...

Domestic Violence Assessments in the Child Advocacy Center

ERIC Educational Resources Information Center

Thackeray, Jonathan D.; Scribano, Philip V.; Rhoda, Dale

2010-01-01

Objective: This study was designed to identify the frequency, methods, and practices of universal assessments for domestic violence (DV) within child advocacy centers (CACs) and determine which factors are associated with CACs that conduct universal DV assessments. Methods: The study design was a cross-sectional, web-based survey distributed to…

Comprehensive missile aerodynamics programs for preliminary design

NASA Technical Reports Server (NTRS)

Dillenius, M. F. E.; Hemsch, M. J.; Sawyer, W. C.; Allen, J. M.; Blair, A. B., Jr.

1982-01-01

Two different classes of missile aeroprediction programs have been recently developed. The first class of programs provides rapid engineering predictions and includes MISSILE1 and MISSILE2 applicable to missile configurations with axisymmetric bodies. The second class of programs consists of the DEMON series, including a simplified version NSWCDM, designed to calculate detailed loadings acting on supersonic missiles which may have non-circular body cross sections. Both classes account for high angles of attack and track vortices from canard or wing section to the tail section. Extensive comparisons with experimental data are presented including nonlinear effects of canard control.

The Genetic Basis of Upland/Lowland Ecotype Divergence in Switchgrass (Panicum virgatum)

PubMed Central

Milano, Elizabeth R.; Lowry, David B.; Juenger, Thomas E.

2016-01-01

The evolution of locally adapted ecotypes is a common phenomenon that generates diversity within plant species. However, we know surprisingly little about the genetic mechanisms underlying the locally adapted traits involved in ecotype formation. The genetic architecture underlying locally adapted traits dictates how an organism will respond to environmental selection pressures, and has major implications for evolutionary ecology, conservation, and crop breeding. To understand the genetic architecture underlying the divergence of switchgrass (Panicum virgatum) ecotypes, we constructed a genetic mapping population through a four-way outbred cross between two northern upland and two southern lowland accessions. Trait segregation in this mapping population was largely consistent with multiple independent loci controlling the suite of traits that characterizes ecotype divergence. We assembled a joint linkage map using ddRADseq, and mapped quantitative trait loci (QTL) for traits that are divergent between ecotypes, including flowering time, plant size, physiological processes, and disease resistance. Overall, we found that most QTL had small to intermediate effects. While we identified colocalizing QTL for multiple traits, we did not find any large-effect QTL that clearly controlled multiple traits through pleiotropy or tight physical linkage. These results indicate that ecologically important traits in switchgrass have a complex genetic basis, and that similar loci may underlie divergence across the geographic range of the ecotypes. PMID:27613751

Defining the Field of Existence of Shrouded Blades in High-Speed Gas Turbines

NASA Astrophysics Data System (ADS)

Belousov, Anatoliy I.; Nazdrachev, Sergeiy V.

2018-01-01

This work provides a method for determining the region of existence of banded blades of gas turbines for aircraft engines based on the analytical evaluation of tensile stresses in specific characteristic sections of the blade. This region is determined by the set of values of the parameter, which forms the law of distribution of the cross-sectional area of the cross-sections along the height of the airfoil. When seven independent parameters (gas-dynamic, structural and strength) are changed, the choice of the best option is proposed at the early design stage. As an example, the influence of the dimension of a turbine on the domain of the existence of banded blades is shown.

Stimulating Divergent Thinking in Junior High Career Education.

ERIC Educational Resources Information Center

Ranke, Charlotte; Champoux, Ellen M.

1981-01-01

Describes a middle school career-oriented teaching unit with emphasis on teaching for divergent thinking. The unit provides hands-on opportunities for eighth-grade students to explore careers using the knowledge and skills developed in their home economics class. The careers are restaurant management, hospitality service, and interior design. (CT)

Interpersonal Skills and Facebook® Use among College Students

ERIC Educational Resources Information Center

Rhodes, Darson L.; Sniatecki, Jessica L.; Rocco, Mary; Todd, Lauren

2015-01-01

The use of Facebook® among college students is prevalent, and its relationship with interpersonal skills is unknown. A cross-sectional design study using a convenience sample of undergraduate students enrolled in one of four sections of an upper-level nutrition course at a Northeastern, public university was conducted to investigate this…

26 CFR 1.401(a)(4)-8 - Cross-testing.

Code of Federal Regulations, 2010 CFR

2010-04-01

... under § 1.401(a)(4)-1(b)(2). Paragraphs (b)(1) and (c)(1) of this section provide general tests for... design basis. (b) Nondiscrimination in amount of benefits provided under a defined contribution plan—(1... this section, were substituted for each employee's allocation rate in the determination of rate groups...

Microcomputers: Applications in Career Counseling and Career Education.

ERIC Educational Resources Information Center

Lambert, Roger, Ed.; Rodenstein, Judith, Ed.

This handbook was designed to help counselors and career development personnel to adopt and adapt to using microcomputers. The 18 papers included in the handbook were written by a cross section of career and counseling professionals as well as experts in microcomputer applications. In the first section of the handbook, the authors examine the…

A methodology to leverage cross-sectional accelerometry to capture weather's influence in active living research.

PubMed

Katapally, Tarun R; Rainham, Daniel; Muhajarine, Nazeem

2016-06-27

While active living interventions focus on modifying urban design and built environment, weather variation, a phenomenon that perennially interacts with these environmental factors, is consistently underexplored. This study's objective is to develop a methodology to link weather data with existing cross-sectional accelerometry data in capturing weather variation. Saskatoon's neighbourhoods were classified into grid-pattern, fractured grid-pattern and curvilinear neighbourhoods. Thereafter, 137 Actical accelerometers were used to derive moderate to vigorous physical activity (MVPA) and sedentary behaviour (SB) data from 455 children in 25 sequential one-week cycles between April and June, 2010. This sequential deployment was necessary to overcome the difference in the ratio between the sample size and the number of accelerometers. A data linkage methodology was developed, where each accelerometry cycle was matched with localized (Saskatoon-specific) weather patterns derived from Environment Canada. Statistical analyses were conducted to depict the influence of urban design on MVPA and SB after factoring in localized weather patterns. Integration of cross-sectional accelerometry with localized weather patterns allowed the capture of weather variation during a single seasonal transition. Overall, during the transition from spring to summer in Saskatoon, MVPA increased and SB decreased during warmer days. After factoring in localized weather, a recurring observation was that children residing in fractured grid-pattern neighbourhoods accumulated significantly lower MVPA and higher SB. The proposed methodology could be utilized to link globally available cross-sectional accelerometry data with place-specific weather data to understand how built and social environmental factors interact with varying weather patterns in influencing active living.

Preliminary Structural Design Considerations and Mass Efficiencies for Lunar Surface Manipulator Concepts

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Mikulas, Martin M.; Doggett, William R.

2008-01-01

The mass and sizing characteristics of manipulators for Lunar and Mars planetary surface applications are investigated by analyzing three structural configurations: a simple cantilevered boom with a square tubular cross-section; a hybrid cable/boom configuration with a square tubular cross-section support structure; and a hybrid cable/boom configuration with a square truss cross-section support structure. Design procedures are developed for the three configurations and numerical examples are given. A new set of performance parameters are developed that relate the mass of manipulators and cranes to a loading parameter. These parameters enable the masses of different manipulator configurations to be compared over a wide range of design loads and reach envelopes (radii). The use of these parameters is demonstrated in the form of a structural efficiency chart using the newly considered manipulator configurations. To understand the performance of Lunar and Mars manipulators, the design procedures were exercised on the three manipulator configurations assuming graphite/epoxy materials for the tubes and trusses. It is also assumed that the actuators are electric motor, gear reduction systems. Numerical results for manipulator masses and sizes are presented for a variety of manipulator reach and payload mass capabilities. Results are presented that demonstrate the sensitivity of manipulator mass to operational radius, tip force, and actuator efficiency. The effect of the value of gravitational force on the ratio of manipulator-mass to payload-mass is also shown. Finally, results are presented to demonstrate the relative mass reduction for the use of graphite/epoxy compared to aluminum for the support structure.

Synthesis, prodigious two-photon absorption cross sections and electrochemical properties of a series of triphenylamine-based chromophores

NASA Astrophysics Data System (ADS)

Li, Rui; Li, Dandan; Fei, Wenwen; Tan, Jingyun; Li, Shengli; Zhou, Hongping; Zhang, Shengyi; Wu, Jieying; Tian, Yupeng

2014-06-01

A series of triphenylamine-based chromophores (L1-3) with donor-π-donor (D-π-D) model have been designed and synthesized via solid phase Wittig reaction. Their one/two-photon fluorescence and electrochemical properties have been investigated. The results show that L2 and L3 exhibited strong and wide-dispersed two-photon-excited fluorescence (TPEF) in different solvents. Chromophore L3 displays the strongest intensity two-photon absorption activity and large cross-sections (>3600 GM) in the range of 680-840 nm in THF, the largest δ up to 8899 GM in the near-IR range, and the measured maximum TPA cross-sections per molecular weight (δmax/MW) is 8.64 GM/g (L3) in THF. Significantly, it also exhibits good solubility in common organic solvents when the chromophore was modified by polyether units as peripheral groups.

Girl in the cellar: a repeated cross-sectional investigation of belief in conspiracy theories about the kidnapping of Natascha Kampusch

PubMed Central

Stieger, Stefan; Gumhalter, Nora; Tran, Ulrich S.; Voracek, Martin; Swami, Viren

2013-01-01

The present study utilized a repeated cross-sectional survey design to examine belief in conspiracy theories about the abduction of Natascha Kampusch. At two time points (October 2009 and October 2011), participants drawn from independent cross-sections of the Austrian population (Time Point 1, N = 281; Time Point 2, N = 277) completed a novel measure of belief in conspiracy theories concerning the abduction of Kampusch, as well as measures of general conspiracist ideation, self-esteem, paranormal and superstitious beliefs, cognitive ability, and media exposure to the Kampusch case. Results indicated that although belief in the Kampusch conspiracy theory declined between testing periods, the effect size of the difference was small. In addition, belief in the Kampusch conspiracy theory was significantly predicted by general conspiracist ideation at both time points. The need to conduct further longitudinal tests of conspiracist ideation is emphasized in conclusion. PMID:23745118

FY17 Status Report on NEAMS Neutronics Activities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, C. H.; Jung, Y. S.; Smith, M. A.

2017-09-30

Under the U.S. DOE NEAMS program, the high-fidelity neutronics code system has been developed to support the multiphysics modeling and simulation capability named SHARP. The neutronics code system includes the high-fidelity neutronics code PROTEUS, the cross section library and preprocessing tools, the multigroup cross section generation code MC2-3, the in-house meshing generation tool, the perturbation and sensitivity analysis code PERSENT, and post-processing tools. The main objectives of the NEAMS neutronics activities in FY17 are to continue development of an advanced nodal solver in PROTEUS for use in nuclear reactor design and analysis projects, implement a simplified sub-channel based thermal-hydraulic (T/H)more » capability into PROTEUS to efficiently compute the thermal feedback, improve the performance of PROTEUS-MOCEX using numerical acceleration and code optimization, improve the cross section generation tools including MC2-3, and continue to perform verification and validation tests for PROTEUS.« less

Design versions of HTS three-phase cables with the minimized value of AC losses

NASA Astrophysics Data System (ADS)

Altov, V. A.; Balashov, N. N.; Degtyarenko, P. N.; Ivanov, S. S.; Kopylov, S. I.; Lipa, DA; Samoilenkov, S. V.; Sytnikov, V. E.; Zheltov, V. V.

2018-03-01

Design versions of HTS three-phase cables consisting of 2G HTS tapes have been investigated by the numerical simulation method with the aim of AC losses minimization. Two design versions of cables with the coaxial and extended rectangular cross-section shape are considered – the non-sectioned and sectioned one. In the latter each cable phase consists of sections connected in parallel. The optimal dimensions of sections and order of their alteration are chosen by appropriate calculations. The model used takes into account the current distribution between the sections and its non-uniformity within each single HTS tape as well. The following characteristics are varied: design version, dimension, positioning of extra copper layer in a cable, design of HTS tapes themselves and their mutual position. The dependence of AC losses on the latter two characteristics is considered in details, and the examples of cable designs optimized by the total set of characteristics for the medium class of voltages (10 – 60 kV) are given. At the critical current JC=5.1 кA per phase and current amplitudes lower than 0.85JC, the level of total AC losses does not exceed the natural cryostat heat losses.

Object-Oriented Multi-Disciplinary Design, Analysis, and Optimization Tool

NASA Technical Reports Server (NTRS)

Pak, Chan-gi

2011-01-01

An Object-Oriented Optimization (O3) tool was developed that leverages existing tools and practices, and allows the easy integration and adoption of new state-of-the-art software. At the heart of the O3 tool is the Central Executive Module (CEM), which can integrate disparate software packages in a cross platform network environment so as to quickly perform optimization and design tasks in a cohesive, streamlined manner. This object-oriented framework can integrate the analysis codes for multiple disciplines instead of relying on one code to perform the analysis for all disciplines. The CEM was written in FORTRAN and the script commands for each performance index were submitted through the use of the FORTRAN Call System command. In this CEM, the user chooses an optimization methodology, defines objective and constraint functions from performance indices, and provides starting and side constraints for continuous as well as discrete design variables. The structural analysis modules such as computations of the structural weight, stress, deflection, buckling, and flutter and divergence speeds have been developed and incorporated into the O3 tool to build an object-oriented Multidisciplinary Design, Analysis, and Optimization (MDAO) tool.

Estimating the Occurrence of Child Maltreatment and Risk-Factor Effects: Benefits of a Mixed-Design Strategy in Epidemiologic Research.

ERIC Educational Resources Information Center

Bertolli, Jeanne; And Others

1995-01-01

This article discusses methodologic limitations of four observational study designs (ecologic, case-control, cross-sectional, and cohort) that dominate the child abuse and neglect literature and identifies key features of an "ideal" study of child maltreatment. It proposes a new mixed-design strategy, which improves ability to identify child…

Aerodynamic design of gas and aerosol samplers for aircraft

NASA Technical Reports Server (NTRS)

Soderman, Paul T.; Hazen, Nathan L.; Brune, William H.

1991-01-01

The aerodynamic design of airborne probes for the capture of air and aerosols is discussed. Emphasis is placed on the key parameters that affect proper sampling, such as inlet-lip design, internal duct components for low pressure drop, and exhaust geometry. Inlet designs that avoid sonic flow conditions on the lip and flow separation in the duct are shown. Cross-stream velocities of aerosols are expressed in terms of droplet density and diameter. Flow curvature, which can cause aerosols to cross streamlines and impact on probe walls, can be minimized by means of a proper inlet shape and proper probe orientation, and by avoiding bends upstream of the test section. A NASA panel code called PMARC was used successfully to compute streamlines around aircraft and probes, as well as to compute to local velocity and pressure distributions in inlets. A NACA 1-series inlet with modified lip radius was used for the airborne capture of stratospheric chlorine monoxide at high altitude and high flight speed. The device has a two-stage inlet that decelerates the inflow with little disturbance to the flow through the test section. Diffuser design, exhaust hood design, valve loss, and corner vane geometry are discussed.

Intravenous volume tomographic pulmonary angiography imaging

NASA Astrophysics Data System (ADS)

Ning, Ruola; Strang, John G.; Chen, Biao; Conover, David L.; Yu, Rongfeng

1999-05-01

This study presents a new intravenous (IV) tomographic angiography imaging technique, called intravenous volume tomographic digital angiography (VTDA) for cross sectional pulmonary angiography. While the advantages of IV-VTDA over spiral CT in terms of volume scanning time and resolution have been validated and reported in our previous papers for head and neck vascular imaging, the superiority of IV-VTDA over spiral CT for cross sectional pulmonary angiography has not been explored yet. The purpose of this study is to demonstrate the advantage of isotropic resolution of IV-VTDA in the x, y and z directions through phantom and animal studies, and to explore its clinical application for detecting clots in pulmonary angiography. A prototype image intensifier-based VTDA imaging system has been designed and constructed by modifying a GE 8800 CT scanner. This system was used for a series of phantom and dog studies. A pulmonary vascular phantom was designed and constructed. The phantom was scanned using the prototype VTDA system for direct 3D reconstruction. Then the same phantom was scanned using a GE CT/i spiral CT scanner using the routine pulmonary CT angiography protocols. IV contrast injection and volume scanning protocols were developed during the dog studies. Both VTDA reconstructed images and spiral CT images of the specially designed phantom were analyzed and compared. The detectability of simulated vessels and clots was assessed as the function of iodine concentration levels, oriented angles, and diameters of the vessels and clots. A set of 3D VTDA reconstruction images of dog pulmonary arteries was obtained with different IV injection rates and isotropic resolution in the x, y and z directions. The results of clot detection studies in dog pulmonary arteries have also been shown. This study presents a new tomographic IV angiography imaging technique for cross sectional pulmonary angiography. The results of phantom and animal studies indicate that IV-VTDA is superior to spiral CT for cross sectional pulmonary angiography.

In search of causality: a systematic review of the relationship between the built environment and physical activity among adults

PubMed Central

2011-01-01

Background Empirical evidence suggests that an association between the built environment and physical activity exists. This evidence is mostly derived from cross-sectional studies that do not account for other causal explanations such as neighborhood self-selection. Experimental and quasi-experimental designs can be used to isolate the effect of the built environment on physical activity, but in their absence, statistical techniques that adjust for neighborhood self-selection can be used with cross-sectional data. Previous reviews examining the built environment-physical activity relationship have not differentiated among findings based on study design. To deal with self-selection, we synthesized evidence regarding the relationship between objective measures of the built environment and physical activity by including in our review: 1) cross-sectional studies that adjust for neighborhood self-selection and 2) quasi-experiments. Method In September 2010, we searched for English-language studies on built environments and physical activity from all available years in health, leisure, transportation, social sciences, and geographical databases. Twenty cross-sectional and 13 quasi-experimental studies published between 1996 and 2010 were included in the review. Results Most associations between the built environment and physical activity were in the expected direction or null. Land use mix, connectivity and population density and overall neighborhood design were however, important determinants of physical activity. The built environment was more likely to be associated with transportation walking compared with other types of physical activity including recreational walking. Three studies found an attenuation in associations between built environment characteristics and physical activity after accounting for neighborhood self-selection. Conclusion More quasi-experiments that examine a broader range of environmental attributes in relation to context-specific physical activity and that measure changes in the built environment, neighborhood preferences and their effect on physical activity are needed. PMID:22077952

Long-distance gene flow and cross-Andean dispersal of lowland rainforest bees (Apidae: Euglossini) revealed by comparative mitochondrial DNA phylogeography.

PubMed

Dick, Christopher W; Roubik, David W; Gruber, Karl F; Bermingham, Eldredge

2004-12-01

Euglossine bees (Apidae; Euglossini) exclusively pollinate hundreds of orchid species and comprise up to 25% of bee species richness in neotropical rainforests. As one of the first studies of comparative phylogeography in a neotropical insect group, we performed a mitochondrial DNA (mtDNA)-based analysis of 14 euglossine species represented by populations sampled across the Andes and/or across the Amazon basin. The mtDNA divergences within species were consistently low; across the 12 monophyletic species the mean intraspecific divergence among haplotypes was 0.9% (range of means, 0-1.9%). The cytochrome oxidase 1 (CO1) divergence among populations separated by the Andes (N = 11 species) averaged 1.1% (range 0.0-2.0%). The mtDNA CO1 data set displayed homogeneous rates of nucleotide substitution, permitting us to infer dispersal across the cordillera long after the final Andean uplift based on arthropod molecular clocks of 1.2-1.5% divergence per million years. Gene flow across the 3000-km breadth of the Amazon basin was inferred from identical cross-Amazon haplotypes found in five species. Although mtDNA haplotypes for 12 of the 14 euglossine species were monophyletic, a reticulate CO1 phylogeny was recovered in Euglossa cognata and E. mixta, suggesting large ancestral populations and recent speciation. Reference to closely related outgroups suggested recent speciation for the majority of species. Phylogeographical structure across a broad spatial scale is weaker in euglossine bees than in any neotropical group previously examined, and may derive from a combination of Quaternary speciation, population expansion and/or long-distance gene flow.

Deducing the form factors for shear used in the calculus of the displacements based on strain energy methods. Mathematical approach for currently used shapes

NASA Astrophysics Data System (ADS)

Constantinescu, E.; Oanta, E.; Panait, C.

2017-08-01

The paper presents an initial study concerning the form factors for shear, for a rectangular and for a circular cross section, being used an analytical method and a numerical study. The numerical study considers a division of the cross section in small areas and uses the power of the definitions in order to compute the according integrals. The accurate values of the form factors are increasing the accuracy of the displacements computed by the use of the strain energy methods. The knowledge resulted from this study will be used for several directions of development: calculus of the form factors for a ring-type cross section of variable ratio of the inner and outer diameters, calculus of the geometrical characteristics of an inclined circular segment and, using a Bool algebra that operates with geometrical shapes, for an inclined circular ring segment. These shapes may be used to analytically define the geometrical model of a complex composite section, i.e. a ship hull cross section. The according calculus relations are also useful for the development of customized design commands in CAD commercial applications. The paper is a result of the long run development of original computer based instruments in engineering of the authors.

Divergence of perturbation theory in large scale structures

NASA Astrophysics Data System (ADS)

Pajer, Enrico; van der Woude, Drian

2018-05-01

We make progress towards an analytical understanding of the regime of validity of perturbation theory for large scale structures and the nature of some non-perturbative corrections. We restrict ourselves to 1D gravitational collapse, for which exact solutions before shell crossing are known. We review the convergence of perturbation theory for the power spectrum, recently proven by McQuinn and White [1], and extend it to non-Gaussian initial conditions and the bispectrum. In contrast, we prove that perturbation theory diverges for the real space two-point correlation function and for the probability density function (PDF) of the density averaged in cells and all the cumulants derived from it. We attribute these divergences to the statistical averaging intrinsic to cosmological observables, which, even on very large and "perturbative" scales, gives non-vanishing weight to all extreme fluctuations. Finally, we discuss some general properties of non-perturbative effects in real space and Fourier space.

Stochastic mixing of protons from chaotic orbits in the nightside geomagnetosphere

NASA Technical Reports Server (NTRS)

Horton, W.; Liu, C.; Hernandez, J.; Tajima, T.

1991-01-01

The stochastic mixing of protons in the energy range from 1 to 30 keV in the nightside magnetosphere is studied by calculating the local divergence rate of neighboring orbits and the two-time velocity correlation function. The rate of divergence of neighboring bundles of trajectories is shown to have large bursts with average separation times of order 1 minute per e-folding during the crossing of the central plasma sheet in the region beyond -50 Re. For the Tsyganenko magnetosphere the net amount of orbit divergence is 15 to 20 e-foldings in one hour. The velocity correlations are shown to decay as power laws r-m with a distribution of m values. These results indicate that for short time (less than 1 hour) there is reversibility and memory for the protons but for longer times there is no memory for protons in the nightside magnetosphere.

Beam-plasma instabilities and the beam-plasma discharge

NASA Technical Reports Server (NTRS)

Kellogg, P. J.; Boswell, R. W.

1986-01-01

Using a new waves on magnetized beams and turbulence (WOMBAT) 0-450 eV electron gun, measurements bearing on the generation of beam-plasma discharge (BPD) are made. The new gun has a narrower divergence angle than the old, and the BPD ignition current is found to be proportional to the cross-sectional area of the plasma. The high-frequency instabilities are identified with the two Trivelpiece-Gould modes, (1959). The upper frequency is identified as a Cerenkov resonance with the upper Trivelpiece-Gould mode, and the lower frequency with a cyclotron resonance with the lower mode, in agreement with theoretical expectations. Convective growth rates are found to be small. A mechanism involving the conversion of a convective instability to an absolute one by trapping of the unstable waves in the density perturbations of the low-frequency waves, is suggested for the low-frequency wave control of the onset of the high frequency precursors to the BPD.

Subleading Regge limit from a soft anomalous dimension

NASA Astrophysics Data System (ADS)

Brüser, Robin; Caron-Huot, Simon; Henn, Johannes M.

2018-04-01

Wilson lines capture important features of scattering amplitudes, for example soft effects relevant for infrared divergences, and the Regge limit. Beyond the leading power approximation, corrections to the eikonal picture have to be taken into account. In this paper, we study such corrections in a model of massive scattering amplitudes in N=4 super Yang-Mills, in the planar limit, where the mass is generated through a Higgs mechanism. Using known three-loop analytic expressions for the scattering amplitude, we find that the first power suppressed term has a very simple form, equal to a single power law. We propose that its exponent is governed by the anomalous dimension of a Wilson loop with a scalar inserted at the cusp, and we provide perturbative evidence for this proposal. We also analyze other limits of the amplitude and conjecture an exact formula for a total cross-section at high energies.

Laser-driven collimated tens-GeV monoenergetic protons from mass-limited target plus preformed channel

NASA Astrophysics Data System (ADS)

Zheng, F. L.; Wu, S. Z.; Wu, H. C.; Zhou, C. T.; Cai, H. B.; Yu, M. Y.; Tajima, T.; Yan, X. Q.; He, X. T.

2013-01-01

Proton acceleration by ultra-intense laser pulse irradiating a target with cross-section smaller than the laser spot size and connected to a parabolic density channel is investigated. The target splits the laser into two parallel propagating parts, which snowplow the back-side plasma electrons along their paths, creating two adjacent parallel wakes and an intense return current in the gap between them. The radiation-pressure pre-accelerated target protons trapped in the wake fields now undergo acceleration as well as collimation by the quasistatic wake electrostatic and magnetic fields. Particle-in-cell simulations show that stable long-distance acceleration can be realized, and a 30 fs monoenergetic ion beam of >10 GeV peak energy and <2° divergence can be produced by a circularly polarized laser pulse at an intensity of about 1022 W/cm2.

Influence of slight to moderate risk for birth hypoxia on acquisition of cognitive and language function in the preterm infant: a cross-sectional comparison with preterm-birth controls.

PubMed

Hopkins-Golightly, Tracy; Raz, Sarah; Sander, Craig J

2003-01-01

The cognitive and language performance of a group of 26 preterm-birth preschool and early school-age children with slight to moderate risk for perinatal hypoxia was compared with the performance of a preterm-birth comparison group of 26 children. Despite the relatively small discrepancy in degree of risk, the cognitive performance of the 2 groups diverged significantly. When data for children with known perinatal arterial pH were combined, a curvilinear (quadratic) regression model provided the best fit. Increasing acidosis was linearly related to decreases in cognitive skills, with the bend in the curve occurring well within the normal range of pH values. Hence, in the preterm infant, even minor risk for birth hypoxia may result in discernible deviation from the expected developmental trajectory.

Divergence of Age-Related Differences in Social-Communication: Improvements for Typically Developing Youth but Declines for Youth with Autism Spectrum Disorder.

PubMed

Wallace, Gregory L; Dudley, Katerina; Anthony, Laura; Pugliese, Cara E; Orionzi, Bako; Clasen, Liv; Lee, Nancy Raitano; Giedd, Jay N; Martin, Alex; Raznahan, Armin; Kenworthy, Lauren

2017-02-01

Although social-communication difficulties and repetitive behaviors are hallmark features of autism spectrum disorder (ASD) and persist across the lifespan, very few studies have compared age-related differences in these behaviors between youth with ASD and same-age typically developing (TD) peers. We examined this issue using SRS-2 (Social Responsiveness Scale-Second Edition) measures of social-communicative functioning and repetitive behaviors in a stratified cross-sectional sample of 324 youth with ASD in the absence of intellectual disability, and 438 TD youth (aged 4-29 years). An age-by-group interaction emerged indicating that TD youth exhibited age-related improvements in social-communication scores while the ASD group demonstrated age-related declines in these scores. This suggests that adolescents/adults with ASD may fall increasingly behind their same-age peers in social-communicative skills.

Experimental observation of two phase flow of R123 inside a herringbone microfin tube

NASA Astrophysics Data System (ADS)

Miyara, Akio; Islam, Mohammad Ariful; Mizuta, Yoshihiko; Kibe, Atsushi

2003-08-01

Vapor-liquid two phase flow behavior of R123 inside herringbone microfin tubes has been studied. Herringbone microfin tube is a kind of internally finned tube in which microfins are installed inside the tube where the microfins form multi-V-shape in flow direction. For the present experiment three different types of herringbone microfin tubes with helix angle β=8°, 14° and 28° are used. Experimental observations showed how flow diverges and converges inside herringbone microfin tube due to fin arrangement. The effect is more remarkable for larger helix angle. From the measurements of the cross-sectional liquid flow rate distribution, the liquid removal and collection and the entrained droplet are discussed. Quantity of liquid droplets is increased with increase of helix angle. The tube with helix angle β=28° shows higher quantity of liquid droplets than others.

Footprints of storms on the sea: A view from spaceborne synthetic aperture radar

NASA Technical Reports Server (NTRS)

Atlas, David

1994-01-01

Synthetic aperture radar (SAR) on board Seasat observed images of stormlike echoes on the sea in 1978. The core of these images is usually an echo-free hole which is attributed to the damping of the short (30-cm) radar detectable gravity waves by the intense rain in the storm core. Although 'the beating down of waves by rain' is consistent with observations by seafarers and with the first scientific explanation of the phenomenon by Reynolds (1875), neither theory nor experiment has provided definitive support. One experiment appears to provide the key; it shows that the kenetic energy of the rain produces sufficient turbulence in a thin fresh water layer to damp 30-cm waves in 10-20 s, thus producing the echo-free hole. A sequence of positive feedbacks then serves to damp the longer waves. The angular dependence of the sea surface echo cross sections seen by Seasat SAR outside the echo-free hole indicates winds diverging from the downdraft induced by the intense rain core. The wind-generated waves and associated echoes extend out to a sharply defined gust front. The sea surface footprint thus mimics the features of a storm microburst. The variations in surface radar cross section due to a combination of rain and wind effects impacts spaceborne measurements of surface winds by scatterometry and rainfall measurements by radar. Portions of this synthesis remain speculative but serve as hypotheses for further research.

Measuring the preference towards patient-centred communication with the Chinese-revised Patient-Practitioner Orientation Scale: a cross-sectional study among physicians and patients in clinical settings in Shanghai, China.

PubMed

Wang, Jie; Zou, Runyu; Fu, Hua; Qian, Haihong; Yan, Yueren; Wang, Fan

2017-09-18

To adapt the Patient-Practitioner Orientation Scale (PPOS), to a Chinese context, and explore the preference towards patient-centred communication among physicians and patients with the Chinese-revised Patient-Practitioner Orientation Scale (CR-PPOS). A cross-sectional questionnaire-based study. Clinical settings from eight medical units, including four community hospitals and four general hospitals, in Shanghai, China. 1018 participants, including 187 physicians and 831 patients, completed this study in two successive stages. Psychometric properties of the CR-PPOS and participants' score on the CR-PPOS. Compared with the original PPOS, the 11-item CR-PPOS obtained better psychometric indices. Physicians and patients scored differently on both the total CR-PPOS and its two subscales. Compared with physicians, the scores of patients were more influenced by their personal characteristics, such as age and education. The CR-PPOS is a better instrument in a Chinese context than the original translated version. The divergence in the extent to which patient-centred communication is preferred among Chinese physicians and patients should be noted. Adapting physicians' communication strategy to patients' preferences based on their personal characteristics can be a viable approach towards improving clinical efficiency. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Safety organizing, emotional exhaustion, and turnover in hospital nursing units.

PubMed

Vogus, Timothy J; Cooil, Bruce; Sitterding, Mary; Everett, Linda Q

2014-10-01

Prior research has found that safety organizing behaviors of registered nurses (RNs) positively impact patient safety. However, little research exists on how engaging in safety organizing affects caregivers. While we know that organizational processes can have divergent effects on organizational and employee outcomes, little research exists on the effects of pursuing highly reliable performance through safety organizing on caregivers. Specifically, we examined whether, and the conditions under which, safety organizing affects RN emotional exhaustion and nursing unit turnover rates. Subjects included 1352 RNs in 50 intensive care, internal medicine, labor, and surgery nursing units in 3 Midwestern acute-care hospitals who completed questionnaires between August and December 2011 and 50 Nurse Managers from the units who completed questionnaires in December 2012. Cross-sectional analyses of RN emotional exhaustion linked to survey data on safety organizing and hospital incident reporting system data on adverse event rates for the year before survey administration. Cross-sectional analysis of unit-level RN turnover rates for the year following the administration of the survey linked to survey data on safety organizing. Multilevel regression analysis indicated that safety organizing was negatively associated with RN emotional exhaustion on units with higher rates of adverse events and positively associated with RN emotional exhaustion with lower rates of adverse events. Tobit regression analyses indicated that safety organizing was associated with lower unit level of turnover rates over time. Safety organizing is beneficial to caregivers in multiple ways, especially on nursing units with high levels of adverse events and over time.

Chinese and Australian Children's Understandings of the Earth: A Cross Cultural Study of Conceptual Development

ERIC Educational Resources Information Center

Tao, Ying; Oliver, Mary; Venville, Grady

2013-01-01

The purpose of this study was to explore Chinese and Australian primary children's conceptual understandings of the Earth. The research was conducted in the interpretive paradigm and was designed to be descriptive with comparative and cross sectional elements. Participants were Year 3 and Year 6 children from three schools in Hunan Province,…

Women's Rising Share of Tertiary Enrollment: A Cross-National Analysis

ERIC Educational Resources Information Center

McDaniel, Anne

2014-01-01

In recent decades, a dramatic shift occurred in higher education throughout the world. Women now enroll in and complete more education than men in the majority of countries. Using a lagged cross-sectional design on a dataset of 75 countries from 1990 to 2008, this study examines the predictors of the current gender gap in tertiary enrollment. I…

Analysis of tracheid development in suppressed-growth Ponderosa Pine using the FPL ring profiler

Treesearch

C. Tim Scott; David W. Vahey

2012-01-01

The Ring Profiler was developed to examine the cross-sectional morphology of wood tracheids in a 12.5-mm core sample. The instrument integrates a specially designed staging apparatus with an optical imaging system to obtain high-contrast, high-resolution images containing about 200-500 tracheids. These images are further enhanced and analyzed to extract tracheid cross-...

Determination of Optimum Cross-section for Oran Highway Revetment

NASA Astrophysics Data System (ADS)

Velioglu, Deniz; Sogut, Erdinc; Guler, Isikhan

2017-04-01

Revetments are shore parallel, sloping coastal structures which are built to provide protection from the negative effects of the sea. The revetment mentioned in this study is located in the City of Oran, Algeria and is currently under construction. This study investigates the determination of the optimum revetment cross section for Oran highway, considering both the hydraulic stability of the revetment and economy. The existence of cliffs in the region and the settlement of the City of Oran created a necessity to re-align Oran highway; therefore, it was shifted towards the Gulf of Oran. Approximately 1 km of the highway is to be constructed on the Mediterranean Sea due to the new alignment. In order to protect the sea side of the road from the adverse effects of the sea, a revetment was designed. The proposed cross section had an armour layer composed of 23 tons of antifer units and regular placement of armour units was recommended. In order to check the hydraulic stability of the proposed section, physical model tests were performed in the laboratory of LEM (Laboratoire d'Etudes Maritimes) in Algeria, using the pre-determined design wave conditions. The physical model tests revealed that the trunk of the revetment was totaly damaged. Accordingly, the proposed section was found insufficient and certain modifications were required. The first modification was made in the arrangement of armour units, changing them from regular to irregular. After testing the new cross section, it was observed that the revetment was vulnerable to breaking wave attack due to the toe geometry and thus the toe of the revetment had to be re-shaped. Therefore, the second option was to reduce the toe elevation. It was observed that even though the revetment trunk was safe, the damage in the toe was not in acceptable limits. The new cross section was found insufficient and as the final option, the weight of the antifer units used in the armour layer was increased, the toe length of the structure was increased and the size of the armour units in the toe was decreased. After the modifications, the new section was tested physically and it was selected as the most optimum option. Acknowledgements: Yuksel Proje Uluslararasi A.S. is acknowledged for its contributon to this study.

Performance of Several Conical Convergent-Divergent Rocket-Type Exhaust Nozzles

NASA Technical Reports Server (NTRS)

Campbell, C. E.; Farley, J. M.

1960-01-01

An investigation was conducted to obtain nozzle performance data with relatively large-scale models at pressure ratios as high as 120. Conical convergent-divergent nozzles with divergence angles alpha of 15, 25, and 29 deg. were each tested at area ratios of approximately 10, 25, and 40. Heated air (1200 F) was supplied at the nozzle inlet at pressures up to 145 pounds per square inch absolute and was exhausted into quiescent air at pressures as low as 1.2 pounds per square inch absolute. Thrust ratios for all nozzle configurations are presented over the range of pressure ratios attainable and were extrapolated when possible to design pressure ratio and beyond. Design thrust ratios decreased with increasing nozzle divergence angle according to the trend predicted by the (1 + cos alpha)/2 parameter. Decreasing the nozzle divergence angle resulted in sizable increases in thrust ratio for a given surface-area ratio (nozzle weight), particularly at low nozzle pressure ratios. Correlations of the nozzle static pressure at separation and of the average static pressure downstream of separation with various nozzle parameters permitted the calculation of thrust in the separated-flow region from unseparated static-pressure distributions. Thrust ratios calculated by this method agreed with measured values within about 1 percent.

A method for (n,alpha) and (n,p) cross section measurements using a lead slowing-down spectrometer

NASA Astrophysics Data System (ADS)

Thompson, Jason Tyler

The need for nuclear data comes from several sources including astrophysics, stockpile stewardship, and reactor design. Photodisintegration, neutron capture, and charged particle out reactions on stable or short-lived radioisotopes play crucial roles during stellar evolution and forming solar isotopic abundances whereas these reactions can affect the safety of our national weapons stockpile or criticality and safety calculations for reactors. Although models can be used to predict some of these values, these predictions are only as good as the experimental data that constrains them. For neutron-induced emission of α particles and protons ((n,α) and (n,p) reactions) at energies below 1 MeV, the experimental data is at best scarce and models must rely on extrapolations from unlike situations, (i.e. different reactions, isotopes, and energies) providing ample room for uncertainty. In this work a new method of measuring energy dependent (n,α) and (n,p) cross sections was developed for the energy range of 0.1 eV - ˜100 keV using a lead slowing-down spectrometer (LSDS). The LSDS provides a ˜10 4 neutron flux increase over the more conventionally used time-of-flight (ToF) methods at equivalent beam conditions, allowing for the measurement of small cross sections (µb’s to mb’s) while using small sample masses (µg’s to mg’s). Several detector concepts were designed and tested, including specially constructed Canberra passivated, implanted, planar silicon (PIPS) detectors; and gas-electron-multiplier (GEM) foils. All designs are compensated to minimize γ-flash problems. The GEM detector was found to function satisfactory for (n,α) measurements, but the PIPS detectors were found to be better suited for (n,p) reaction measurements. A digital data acquisition (DAQ) system was programmed such that background can be measured simultaneously with the reaction cross section. Measurements of the 147Sm(n,α)144Nd and 149 Sm(n,α)146Nd reaction cross sections were performed as proofs of concept. The measurement of 147Sm verified and extended a previous measurement while the measurement of 149Sm is the first over the majority of the 0.1 eV to 100 keV energy region.

[Torque resistance of three different types of nickel-titanium rotary instruments].

PubMed

Sun, Wei; Hou, Ben-xiang

2010-10-01

To compare torsional fracture of three different types of nickel-titanium rotary instruments ProTaper, Hero642 and Mtwo by making a stimulate models in vitro. Through the establishment of model in vitro, compared the different time with 3 kinds of nickel titanium file in cutting-edge bound occurs, and to observe the section of fractured instruments by scanning electron microscope. The resistence to torque was different from three types of nickel titanium instruments. The time to fracture of Mtwo was significantly longer than ProTaper's and Hero642's, but ProTaper's and Hero642's had no significant difference. Three kinds cross-sectional design were different, a lot of toughness nests were seen in broken surface. Most of them were ductile fracture. Time to fracture was influenced by the quality disfigurement. The resistance to torque of Mtwo was better than ProTaper and Hero642. The lifespan was influenced by the design of cross-section. The quality disfigurement of the files reduced the resistance to flexual fatigue.

Origami tubes with reconfigurable polygonal cross-sections.

PubMed

Filipov, E T; Paulino, G H; Tachi, T

2016-01-01

Thin sheets can be assembled into origami tubes to create a variety of deployable, reconfigurable and mechanistically unique three-dimensional structures. We introduce and explore origami tubes with polygonal, translational symmetric cross-sections that can reconfigure into numerous geometries. The tubular structures satisfy the mathematical definitions for flat and rigid foldability, meaning that they can fully unfold from a flattened state with deformations occurring only at the fold lines. The tubes do not need to be straight and can be constructed to follow a non-linear curved line when deployed. The cross-section and kinematics of the tubular structures can be reprogrammed by changing the direction of folding at some folds. We discuss the variety of tubular structures that can be conceived and we show limitations that govern the geometric design. We quantify the global stiffness of the origami tubes through eigenvalue and structural analyses and highlight the mechanical characteristics of these systems. The two-scale nature of this work indicates that, from a local viewpoint, the cross-sections of the polygonal tubes are reconfigurable while, from a global viewpoint, deployable tubes of desired shapes are achieved. This class of tubes has potential applications ranging from pipes and micro-robotics to deployable architecture in buildings.

Origami tubes with reconfigurable polygonal cross-sections

PubMed Central

Filipov, E. T.; Paulino, G. H.; Tachi, T.

2016-01-01

Thin sheets can be assembled into origami tubes to create a variety of deployable, reconfigurable and mechanistically unique three-dimensional structures. We introduce and explore origami tubes with polygonal, translational symmetric cross-sections that can reconfigure into numerous geometries. The tubular structures satisfy the mathematical definitions for flat and rigid foldability, meaning that they can fully unfold from a flattened state with deformations occurring only at the fold lines. The tubes do not need to be straight and can be constructed to follow a non-linear curved line when deployed. The cross-section and kinematics of the tubular structures can be reprogrammed by changing the direction of folding at some folds. We discuss the variety of tubular structures that can be conceived and we show limitations that govern the geometric design. We quantify the global stiffness of the origami tubes through eigenvalue and structural analyses and highlight the mechanical characteristics of these systems. The two-scale nature of this work indicates that, from a local viewpoint, the cross-sections of the polygonal tubes are reconfigurable while, from a global viewpoint, deployable tubes of desired shapes are achieved. This class of tubes has potential applications ranging from pipes and micro-robotics to deployable architecture in buildings. PMID:26997894

The wire material and cross-section effect on double delta closing loops regarding load and spring rate magnitude: an in vitro study.

PubMed

Ferreira, M do A

1999-03-01

The mechanical behavior of orthodontics closing loops, with three different wire materials (stainless steel, cobalt-chromium and titanium-molybdenum) and with different cross-sections and a double delta design, was studied in tension tests. The springs were stress-relieved, except the titanium-molybdenum wires. There were 72 sample springs, divided into 33 stainless steel, 26 cobalt-chromium and 13 titanium-molybdenum, activated at 0.5 mm intervals, from neutral position to 3.0 mm. It was hypothesized that loads, after spring activation, and spring rate, are dependent on cross-section, wire material, and activation. The analysis of variance and the Tukey-Kramer test were applied to verify the differences between all coupled averages of the loads. Regression analysis was also used to verify if closing loops behavior was in accordance with Hooke's law and to obtain the spring rate. The results show that the loads are dependent on activation, cross-section, and wire material. Titanium-molybdenum 0.017 x 0.025 inch (Ormco) springs showed the smallest loads and the best spring rate. (beta = 84.9 g/mm)

Pixelated Checkerboard Metasurface for Ultra-Wideband Radar Cross Section Reduction.

PubMed

Haji-Ahmadi, Mohammad-Javad; Nayyeri, Vahid; Soleimani, Mohammad; Ramahi, Omar M

2017-09-12

In this paper we designed and fabricated a metasurface working as a radar cross section (RCS) reducer over an ultra wide band of frequency from 3.8 to 10.7 GHz. The designed metasurface is a chessboard-like surface made of alternating tiles, with each tile composed of identical unit cells. We develop a novel, simple, highly robust and fully automated approach for designing the unit cells. First, a topology optimization algorithm is used to engineer the shape of the two unit cells. The area of each unit cell is pixelated. A particle swarm optimization algorithm is applied wherein each pixel corresponds to a bit having a binary value of 1 or 0 indicating metallization or no metallization. With the objective of reducing the RCS over a specified frequency range, the optimization algorithm is then linked to a full wave three-dimensional electromagnetic simulator. To validate the design procedure, a surface was designed, fabricated and experimentally tested showing significantly enhanced performance than previous works. Additionally, angular analysis is also presented showing good stability and wide-angle behavior of the designed RCS reducer. The automated design procedure has a wide range of applications and can be easily extended to design surfaces for antennas, energy harvesters, noise mitigation in electronic circuit boards amongst others.

Validation of the WIMSD4M cross-section generation code with benchmark results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deen, J.R.; Woodruff, W.L.; Leal, L.E.

1995-01-01

The WIMSD4 code has been adopted for cross-section generation in support of the Reduced Enrichment Research and Test Reactor (RERTR) program at Argonne National Laboratory (ANL). Subsequently, the code has undergone several updates, and significant improvements have been achieved. The capability of generating group-collapsed micro- or macroscopic cross sections from the ENDF/B-V library and the more recent evaluation, ENDF/B-VI, in the ISOTXS format makes the modified version of the WIMSD4 code, WIMSD4M, very attractive, not only for the RERTR program, but also for the reactor physics community. The intent of the present paper is to validate the WIMSD4M cross-section librariesmore » for reactor modeling of fresh water moderated cores. The results of calculations performed with multigroup cross-section data generated with the WIMSD4M code will be compared against experimental results. These results correspond to calculations carried out with thermal reactor benchmarks of the Oak Ridge National Laboratory (ORNL) unreflected HEU critical spheres, the TRX LEU critical experiments, and calculations of a modified Los Alamos HEU D{sub 2}O moderated benchmark critical system. The benchmark calculations were performed with the discrete-ordinates transport code, TWODANT, using WIMSD4M cross-section data. Transport calculations using the XSDRNPM module of the SCALE code system are also included. In addition to transport calculations, diffusion calculations with the DIF3D code were also carried out, since the DIF3D code is used in the RERTR program for reactor analysis and design. For completeness, Monte Carlo results of calculations performed with the VIM and MCNP codes are also presented.« less

Validation of the WIMSD4M cross-section generation code with benchmark results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leal, L.C.; Deen, J.R.; Woodruff, W.L.

1995-02-01

The WIMSD4 code has been adopted for cross-section generation in support of the Reduced Enrichment for Research and Test (RERTR) program at Argonne National Laboratory (ANL). Subsequently, the code has undergone several updates, and significant improvements have been achieved. The capability of generating group-collapsed micro- or macroscopic cross sections from the ENDF/B-V library and the more recent evaluation, ENDF/B-VI, in the ISOTXS format makes the modified version of the WIMSD4 code, WIMSD4M, very attractive, not only for the RERTR program, but also for the reactor physics community. The intent of the present paper is to validate the procedure to generatemore » cross-section libraries for reactor analyses and calculations utilizing the WIMSD4M code. To do so, the results of calculations performed with group cross-section data generated with the WIMSD4M code will be compared against experimental results. These results correspond to calculations carried out with thermal reactor benchmarks of the Oak Ridge National Laboratory(ORNL) unreflected critical spheres, the TRX critical experiments, and calculations of a modified Los Alamos highly-enriched heavy-water moderated benchmark critical system. The benchmark calculations were performed with the discrete-ordinates transport code, TWODANT, using WIMSD4M cross-section data. Transport calculations using the XSDRNPM module of the SCALE code system are also included. In addition to transport calculations, diffusion calculations with the DIF3D code were also carried out, since the DIF3D code is used in the RERTR program for reactor analysis and design. For completeness, Monte Carlo results of calculations performed with the VIM and MCNP codes are also presented.« less

Random Combinatorial Gradient Metasurface for Broadband, Wide-Angle and Polarization-Independent Diffusion Scattering.

PubMed

Zhuang, Yaqiang; Wang, Guangming; Liang, Jiangang; Cai, Tong; Tang, Xiao-Lan; Guo, Tongfeng; Zhang, Qingfeng

2017-11-29

This paper proposes an easy, efficient strategy for designing broadband, wide-angle and polarization-independent diffusion metasurface for radar cross section (RCS) reduction. A dual-resonance unit cell, composed of a cross wire and cross loop (CWCL), is employed to enhance the phase bandwidth covering the 2π range. Both oblique-gradient and horizontal-gradient phase supercells are designed for illustration. The numerical results agree well with the theoretical ones. To significantly reduce backward scattering, the random combinatorial gradient metasurface (RCGM) is subsequently constructed by collecting eight supercells with randomly distributed gradient directions. The proposed metasurface features an enhanced specular RCS reduction performance and less design complexity compared to other candidates. Both simulated and measured results show that the proposed RCGM can significantly suppress RCS and exhibits broadband, wide-angle and polarization independence features.

Genetic loci with parent-of-origin effects cause hybrid seed lethality in crosses between Mimulus species.

PubMed

Garner, Austin G; Kenney, Amanda M; Fishman, Lila; Sweigart, Andrea L

2016-07-01

In flowering plants, F1 hybrid seed lethality is a common outcome of crosses between closely related diploid species, but the genetic basis of this early-acting and potentially widespread form of postzygotic reproductive isolation is largely unknown. We intercrossed two closely related species of monkeyflower, Mimulus guttatus and Mimulus tilingii, to characterize the mechanisms and strength of postzygotic reproductive isolation. Then, using a reciprocal backcross design, we performed high-resolution genetic mapping to determine the genetic architecture of hybrid seed lethality and directly test for loci with parent-of-origin effects. We found that F1 hybrid seed lethality is an exceptionally strong isolating barrier between Mimulus species, with reciprocal crosses producing < 1% viable seeds. This form of postzygotic reproductive isolation appears to be highly polygenic, indicating that multiple incompatibility loci have accumulated rapidly between these closely related Mimulus species. It is also primarily caused by genetic loci with parent-of-origin effects, suggesting a possible role for imprinted genes in the evolution of Mimulus hybrid seed lethality. Our findings suggest that divergence in loci with parent-of-origin effects, which is probably driven by genomic coevolution within lineages, might be an important source of hybrid incompatibilities between flowering plant species. © 2016 The Authors. New Phytologist © 2016 New Phytologist Trust.

Strategies for improving approximate Bayesian computation tests for synchronous diversification.

PubMed

Overcast, Isaac; Bagley, Justin C; Hickerson, Michael J

2017-08-24

Estimating the variability in isolation times across co-distributed taxon pairs that may have experienced the same allopatric isolating mechanism is a core goal of comparative phylogeography. The use of hierarchical Approximate Bayesian Computation (ABC) and coalescent models to infer temporal dynamics of lineage co-diversification has been a contentious topic in recent years. Key issues that remain unresolved include the choice of an appropriate prior on the number of co-divergence events (Ψ), as well as the optimal strategies for data summarization. Through simulation-based cross validation we explore the impact of the strategy for sorting summary statistics and the choice of prior on Ψ on the estimation of co-divergence variability. We also introduce a new setting (β) that can potentially improve estimation of Ψ by enforcing a minimal temporal difference between pulses of co-divergence. We apply this new method to three empirical datasets: one dataset each of co-distributed taxon pairs of Panamanian frogs and freshwater fishes, and a large set of Neotropical butterfly sister-taxon pairs. We demonstrate that the choice of prior on Ψ has little impact on inference, but that sorting summary statistics yields substantially more reliable estimates of co-divergence variability despite violations of assumptions about exchangeability. We find the implementation of β improves estimation of Ψ, with improvement being most dramatic given larger numbers of taxon pairs. We find equivocal support for synchronous co-divergence for both of the Panamanian groups, but we find considerable support for asynchronous divergence among the Neotropical butterflies. Our simulation experiments demonstrate that using sorted summary statistics results in improved estimates of the variability in divergence times, whereas the choice of hyperprior on Ψ has negligible effect. Additionally, we demonstrate that estimating the number of pulses of co-divergence across co-distributed taxon-pairs is improved by applying a flexible buffering regime over divergence times. This improves the correlation between Ψ and the true variability in isolation times and allows for more meaningful interpretation of this hyperparameter. This will allow for more accurate identification of the number of temporally distinct pulses of co-divergence that generated the diversification pattern of a given regional assemblage of sister-taxon-pairs.

Planar near-field scanning for compact range bistatic radar cross-section measurement. Thesis Final Report

NASA Technical Reports Server (NTRS)

Tuhela-Reuning, S. R.; Walton, E. K.

1991-01-01

The design, construction, and testing of a low cost, planar scanning system to be used in a compact range environment for bistatic radar cross-section (bistatic RCS) measurement data are discussed. This scanning system is similar to structures used for measuring near-field antenna patterns. A synthetic aperture technique is used for plane wave reception. System testing entailed comparison of measured and theoretical bistatic RCS of a sphere and a right circular cylinder. Bistatic scattering analysis of the ogival target support, target and pedestal interactions, and compact range room was necessary to determine measurement validity.

Design and simulation of MEMS vector hydrophone with reduced cross section based meander beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Manoj; Dutta, S.; Pal, Ramjay

MEMS based vector hydrophone is being one of the key device in the underwater communications. In this paper, we presented a bio-inspired MEMS vector hydrophone. The hydrophone structure consists of a proof mass suspended by four meander type beams with reduced cross-section. Modal patterns of the structure were studied. First three modal frequencies of the hydrophone structure were found to be 420 Hz, 420 Hz and 1646 Hz respectively. The deflection and stress of the hydrophone is found have linear behavior in the 1 µPa – 1Pa pressure range.

Design, manufacturing and measurement of a PV miniconcentrator for front point-contact silicon solar cells

NASA Astrophysics Data System (ADS)

Pérez, D.; Miñano, J. C.; Benítez, P.; Muñoz, F.; Mohedano, R.

2005-08-01

A novel photovoltaic concentrator has been developed in the framework of the European project "High efficiency silicon solar cells concentrator". In this project, front-contacted silicon solar cell have also been designed and manufactured by the project leader (the French LETI). This silicon cell concept is potentially capable to perform well (24% efficiency has been predicted) for much higher concentration levels than the back-contacted cells (and, of course, than the two-side contacted cells). The concentrator is formed by one lens of squared contour with flat entry surface and large-facet Fresnel exit surface, and a secondary that encapsulates the solar cell. On the contrary to the conventional Fresnel lens plus nonimaging secondary concentrators, the primary and secondary are designed simultaneously, leading to better concentration-acceptance angle product without compromise with the compactness. The grid lines in the front-contacted cells are aluminium prisms (which contact the p+ and n+ emitters, alternatively), acting as a linear cone concentrator that concentrates Cg =1.52× in the cross sectional dimension of the prisms. The secondary concentrator has a refractive rotational symmetric top surface that is crossed with two linear flow-line TIR mirror. Then, in the cross section normal to the aluminium prisms, the secondary provides a 2D concentration of Cg =12×, while in the cross section parallel to the prisms it provides a 2D concentration of Cg =24.16× as the grid lines in this dimension. Therefore, the cell is rectangular (1:2.08 aspect ratio), being the grid lines parallel to the shorter rectangle side. The total 3D geometrical concentration is 24.16×(12×1.52) = 455× for the square aperture and rectangular cell, and gets a design acceptance angle α=+/-1.8 degrees. Injection moulded prototypes are have been manufactured and measured, proving an optical efficiency of 79%. Computer modelling of the concentrator performance will also be presented.

A Passive Cavity Concept for Improving the Off-Design Performance of Fixed-Geometry Exhaust Nozzles

NASA Technical Reports Server (NTRS)

Asbury, Scott C.; Gunther, Christopher L.; Hunter, Craig A.

1996-01-01

An investigation was conducted in the model preparation area of the Langley 16-Foot Transonic Tunnel to study a passive cavity concept for improving the off-design performance of fixed-geometry exhaust nozzles. Passive cavity ventilation (through a porous surface) was applied to divergent flap surfaces and tested at static conditions in a sub-scale, nonaxisymmetric, convergent-divergent nozzle. As part of a comprehensive investigation, force, moment and pressure measurements were taken and focusing schlieren flow visualization was obtained for a baseline configuration and D passive cavity configurations. All tests were conducted with no external flow and high-pressure air was used to simulate jet-exhaust flow at nozzle pressure ratios from 1.25 to approximately 9.50. Results indicate that baseline nozzle performance was dominated by unstable shock-induced boundary-layer separation at off-design conditions, which came about through the natural tendency of overexpanded exhaust flow to satisfy conservation requirements by detaching from the nozzle divergent flaps. Passive cavity ventilation added the ability to control off-design separation in the nozzle by either alleviating separation or encouraging stable separation of the exhaust flow. Separation alleviation offers potential for installed nozzle performance benefits by reducing drag at forward flight speeds, even though it may reduce off-design static thrust efficiency as much as 3.2 percent. Encouraging stable separation of the exhaust flow offers significant performance improvements at static, low NPR and low Mach number flight conditions by improving off-design static thrust efficiency as much as 2.8 percent. By designing a fixed-geometry nozzle with fully porous divergent flaps, where both cavity location and percent open porosity of the flaps could be varied, passive flow control would make it possible to improve off-design nozzle performance across a wide operating range. In addition, the ability to encourage separation on one flap while alleviating it on the other makes it possible to generate thrust vectoring in the nozzle through passive flow control.

Mapping the Diagnosis Axis of an Interface Terminology to the NANDA International Taxonomy

PubMed Central

Juvé Udina, Maria-Eulàlia; Gonzalez Samartino, Maribel; Matud Calvo, Cristina

2012-01-01

Background. Nursing terminologies are designed to support nursing practice but, as with any other clinical tool, they should be evaluated. Cross-mapping is a formal method for examining the validity of the existing controlled vocabularies. Objectives. The study aims to assess the inclusiveness and expressiveness of the nursing diagnosis axis of a newly implemented interface terminology by cross-mapping with the NANDA-I taxonomy. Design/Methods. The study applied a descriptive design, using a cross-sectional, bidirectional mapping strategy. The sample included 728 concepts from both vocabularies. Concept cross-mapping was carried out to identify one-to-one, negative, and hierarchical connections. The analysis was conducted using descriptive statistics. Results. Agreement of the raters' mapping achieved 97%. More than 60% of the nursing diagnosis concepts in the NANDA-I taxonomy were mapped to concepts in the diagnosis axis of the new interface terminology; 71.1% were reversely mapped. Conclusions. Main results for outcome measures suggest that the diagnosis axis of this interface terminology meets the validity criterion of cross-mapping when mapped from and to the NANDA-I taxonomy. PMID:22830046

Mapping the Diagnosis Axis of an Interface Terminology to the NANDA International Taxonomy.

PubMed

Juvé Udina, Maria-Eulàlia; Gonzalez Samartino, Maribel; Matud Calvo, Cristina

2012-01-01

Background. Nursing terminologies are designed to support nursing practice but, as with any other clinical tool, they should be evaluated. Cross-mapping is a formal method for examining the validity of the existing controlled vocabularies. Objectives. The study aims to assess the inclusiveness and expressiveness of the nursing diagnosis axis of a newly implemented interface terminology by cross-mapping with the NANDA-I taxonomy. Design/Methods. The study applied a descriptive design, using a cross-sectional, bidirectional mapping strategy. The sample included 728 concepts from both vocabularies. Concept cross-mapping was carried out to identify one-to-one, negative, and hierarchical connections. The analysis was conducted using descriptive statistics. Results. Agreement of the raters' mapping achieved 97%. More than 60% of the nursing diagnosis concepts in the NANDA-I taxonomy were mapped to concepts in the diagnosis axis of the new interface terminology; 71.1% were reversely mapped. Conclusions. Main results for outcome measures suggest that the diagnosis axis of this interface terminology meets the validity criterion of cross-mapping when mapped from and to the NANDA-I taxonomy.

A comprehensive safety assessment methodology for innovative geometric designs.

DOT National Transportation Integrated Search

2017-05-01

As the population grows and travel demands increase, alternative interchange designs have become increasingly popular. The diverging diamond interchange is an alternative design that has been implemented in the United States. This design can accommod...

SU-F-T-504: Non-Divergent Planning Method for Craniospinal Irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sperling, N; Bogue, J; Parsai, E

2016-06-15

Purpose: Traditional Craniospinal Irradiation (CSI) planning techniques require careful field placement to allow optimal divergence and field overlap at depth, and measurement of skin gap. The result of this is a necessary field overlap resulting in dose heterogeneity in the spinal canal. A novel, nondivergent field matching method has been developed to allow simple treatment planning and delivery without the need to measure skin gap. Methods: The CSI patient was simulated in the prone, and a plan was developed. Bilateral cranial fields were designed with couch and collimator rotation to eliminate divergence with the upper spine field and minimize anteriormore » divergence into the lenses. Spinal posterior-to-anterior fields were designed with the couch rotated to 90 degrees to allow gantry rotation to eliminate divergence at the match line, and the collimator rotated to 90 degrees to allow appropriate field blocking with the MLCs. A match line for the two spinal fields was placed and the gantry rotated to equal angles in opposite directions about the match line. Jaw positions were then defined to allow 1mm overlap at the match line to avoid cold spots. A traditional CSI plan was generated using diverging spinal fields, and a comparison between the two techniques was generated. Results: The non-divergent treatment plan was able to deliver a highly uniform dose to the spinal cord with a cold spot of only 95% and maximum point dose of 115.8%, as compared to traditional plan cold spots of 87% and hot spots of 132% of the prescription dose. Conclusion: A non-divergent method for planning CSI patients has been developed and clinically implemented. Planning requires some geometric manipulation in order to achieve an adequate dose distribution, however, it can help to manage cold spots and simplify the shifts needed between spinal fields.« less

Convergent and Divergent Validity of the Grammaticality and Utterance Length Instrument

ERIC Educational Resources Information Center

Castilla-Earls, Anny; Fulcher-Rood, Katrina

2018-01-01

Purpose: This feasibility study examines the convergent and divergent validity of the Grammaticality and Utterance Length Instrument (GLi), a tool designed to assess the grammaticality and average utterance length of a child's prerecorded story retell. Method: Three raters used the GLi to rate audio-recorded story retells from 100 English-speaking…

Undertaking Experiments in Social Sciences: Sequential, Multiple Time Series Designs for Consideration

ERIC Educational Resources Information Center

Phan, Huy P.; Ngu, Bing H.

2017-01-01

In social sciences, the use of stringent methodological approaches is gaining increasing emphasis. Researchers have recognized the limitations of cross-sectional, non-manipulative data in the study of causality. True experimental designs, in contrast, are preferred as they represent rigorous standards for achieving causal flows between variables.…

Using Faculty Characteristics to Predict Attitudes toward Developmental Education

ERIC Educational Resources Information Center

Sides, Meredith Louise Carr

2017-01-01

The study adapted Astin's I-E-O model and utilized multiple regression analyses to predict faculty attitudes toward developmental education. The study utilized a cross-sectional survey design to survey faculty members at 27 different higher education institutions in the state of Alabama. The survey instrument was a self-designed questionnaire that…

Linking Teacher Competences to Organizational Citizenship Behaviour: The Role of Empowerment

ERIC Educational Resources Information Center

Kasekende, Francis; Munene, John C.; Otengei, Samson Omuudu; Ntayi, Joseph Mpeera

2016-01-01

Purpose: The purpose of this paper is to examine relationship between teacher competences and organizational citizenship behavior (OCB) with empowerment as a mediating factor. Design/methodology/approach: The study took a cross-sectional descriptive and analytical design. Using cluster and random sampling procedures, data were obtained from 383…

Health Science Students' Perception about Research Training Programs Offered in Saudi Universities

ERIC Educational Resources Information Center

Al Kuwaiti, Ahmed; Subbarayalu, Arun Vijay

2015-01-01

Purpose: The purpose of this paper was to examine the perceptions of students of health sciences on research training programs offered at Saudi universities. Design/methodology/approach: A cross-sectional survey design was adopted to capture the perceptions of health science students about research training programs offered at selected Saudi…

Parent-Reported Social Support for Child's Fruit and Vegetable Intake: Validity of Measures

ERIC Educational Resources Information Center

Dave, Jayna M.; Evans, Alexandra E.; Condrasky, Marge D.; Williams, Joel E.

2012-01-01

Objective: To develop and validate measures of parental social support to increase their child's fruit and vegetable (FV) consumption. Design: Cross-sectional study design. Setting: School and home. Participants: Two hundred three parents with at least 1 elementary school-aged child. Main Outcome Measure: Parents completed a questionnaire that…

Students' Attitudes towards School-Based Sex and Relationships Education in Tanzania

ERIC Educational Resources Information Center

Mkumbo, Kitila A. K.

2014-01-01

Objective: The objective of this paper was to assess students' attitudes towards school-based sex and relationships education (SRE). Design: This study featured a cross-sectional survey design. Method: A sample of 715 students from two districts in Tanzania completed a survey questionnaire assessing various aspects related to their attitudes…

Motivational Factors and Teachers Commitment in Public Secondary Schools in Mbale Municipality

ERIC Educational Resources Information Center

Olurotimi, Ogunlade Joseph; Asad, Kamonges Wahab; Abdulrauf, Abdulkadir

2015-01-01

The study investigated the influence of motivational factors on teachers' commitment in public Secondary School in Mbale Municipality. The study employed Cross-sectional survey design. The sampling technique used to select was simple random sampling technique. The instrument used to collect data was a self designed questionnaire. The data…

Stroke Survivors' Evaluations of a Stroke Workbook-Based Intervention Designed to Increase Perceived Control over Recovery

ERIC Educational Resources Information Center

Joice, Sara; Johnston, Marie; Bonetti, Debbie; Morrison, Val; MacWalter, Ron

2012-01-01

Objective: To report stroke survivors' experiences and perceived usefulness of an effective self-help workbook-based intervention. Design: A cross-sectional study involving the intervention group of an earlier randomized controlled trial. Setting: At the participants' homes approximately seven weeks post-hospital discharge. Method: Following the…

Determinants of Low-Fat Eating Behaviors among Midlife African American Women

ERIC Educational Resources Information Center

Evans, Gina L.; McNeil, Lorna H.; Laufman, Larry; Bowman, Sharon L.

2009-01-01

Objective: The purpose of this study was to explore midlife African American women's low-fat eating habits in the context of health attitudes, social support, and food preferences. Design: A cross-sectional design was used. Settings: One Midwestern and 1 national African American women's organization were targeted for data collection.…

Predictors of Paternal and Maternal Controlling Feeding Practices with 2- to 5-Year-Old Children

ERIC Educational Resources Information Center

Haycraft, Emma; Blissett, Jackie

2012-01-01

Objective: This study aimed to identify predictors of controlling feeding practices in both mothers and fathers of young children. Design: Cross-sectional, questionnaire design. Setting: Nursery schools within the United Kingdom recruited participants. Participants: Ninety-six mothers and fathers comprising 48 mother-father pairs of male and…

Sexuality Education in South African Schools: The Challenge for Civil Society Organisations

ERIC Educational Resources Information Center

Adams Tucker, Leigh; George, Gavin; Reardon, Candice; Panday, Saadhna

2017-01-01

Objective: Drawing on the perceptions of various key stakeholders, the paper explores the strengths and limitations of involving civil society organisations in the delivery of HIV and AIDS and sexuality education in South African schools. Design: Qualitative study with a cross-sectional design. Setting: Research was conducted at 16 public…

Parametric bicubic spline and CAD tools for complex targets shape modelling in physical optics radar cross section prediction

NASA Astrophysics Data System (ADS)

Delogu, A.; Furini, F.

1991-09-01

Increasing interest in radar cross section (RCS) reduction is placing new demands on theoretical, computation, and graphic techniques for calculating scattering properties of complex targets. In particular, computer codes capable of predicting the RCS of an entire aircraft at high frequency and of achieving RCS control with modest structural changes, are becoming of paramount importance in stealth design. A computer code, evaluating the RCS of arbitrary shaped metallic objects that are computer aided design (CAD) generated, and its validation with measurements carried out using ALENIA RCS test facilities are presented. The code, based on the physical optics method, is characterized by an efficient integration algorithm with error control, in order to contain the computer time within acceptable limits, and by an accurate parametric representation of the target surface in terms of bicubic splines.

980 nm tapered lasers with photonic crystal structure for low vertical divergence

NASA Astrophysics Data System (ADS)

Ma, Xiaolong; Qu, Hongwei; Zhao, Pengchao; Liu, Yun; Zheng, Wanhua

2016-10-01

High power tapered lasers with nearly diffraction-limited beam quality have attracted much attention in numerous applications such as nonlinear frequency conversion, optical pumping of solid-state and fiber lasers, medical treatment and others. However, the large vertical divergence of conventional tapered lasers is a disadvantage, which makes beam shaping difficult and expensive in applications. Diode lasers with photonic crystal structure can achieve a large mode size and a narrow vertical divergence. In this paper, we present tapered lasers with photonic crystal structure emitting at 980 nm. The epitaxial layer is grown using metal organic chemical vapor deposition. The device has a total cavity length of 2 mm, which consists of a 400-um long ridge-waveguide section and a 1600-um long tapered section. The taper angle is 4°. An output power of 3.3 W is achieved with a peak conversion efficiency of 35% in pulsed mode. The threshold current is 240 mA and the slope efficiency is 0.78 W/A. In continuous wave mode, the output power is 2.87 W, which is limited by a suddenly failure resulting from catastrophic optical mirror damage. The far field divergences with full width at half maximum are 12.3° in the vertical direction and 2.9° in the lateral direction at 0.5 A. At high injection level the vertical divergence doesn't exceed 16°. Beam quality factor M2 is measured based on second moment definition in CW mode. High beam quality is demonstrated by M2 value of less than 2 in both vertical and lateral directions.

Evolution: sociality as a driver of unorthodox reproduction.

PubMed

Schwander, Tanja; Keller, Laurent

2012-07-10

An unusual reproductive system was discovered in desert ants, in which daughter queens are produced asexually via parthenogenesis, whereas workers develop from hybrid crosses between genetically divergent lineages. The system appears to be doomed to extinction. Copyright © 2012 Elsevier Ltd. All rights reserved.

Developmental Inter-Relationships Among Concrete Operational Tasks: An Investigation of Piaget's Stage Concept

ERIC Educational Resources Information Center

Jamison, Wesley

1977-01-01

Two models of intertask relations, Wohlwill's divergent-decalage and reciprocal-interaction patterns, were evaluated for their fit to cross-classification tables which showed the joint classification of 101 children's performance on all possible pairs of eight concrete operational tasks. (SB)

Eco-evo-devo in the Study of Adaptive Divergence: Examples from Threespine Stickleback (Gasterosteus aculeatus).

PubMed

Jamniczky, Heather A; Barry, Tegan N; Rogers, Sean M

2015-07-01

The tight fit between form and function in organisms suggests the influence of adaptive evolution in biomechanics; however, the prevalence of adaptive traits, the mechanisms by which they arise and the corresponding responses to selection are subjects of extensive debate. We used three-dimensional microcomputed tomography and geometric morphometrics to characterize the structure of phenotypic covariance within the G. aculeatus trophic apparatus and its supporting structures in wild and controlled crosses of fish from two different localities. Our results reveal that while the structure of phenotypic covariance is conserved in marine and freshwater forms, it may be disrupted in the progeny of artificial crosses or during rapid adaptive divergence events. We discuss these results within the context of integrating covariance structure with quantitative genetics, toward establishing predictive links between genes, development, biomechanics, and the environment. © The Author 2015. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

Design and application of a small size SAFT imaging system for concrete structure

NASA Astrophysics Data System (ADS)

Shao, Zhixue; Shi, Lihua; Shao, Zhe; Cai, Jian

2011-07-01

A method of ultrasonic imaging detection is presented for quick non-destructive testing (NDT) of concrete structures using synthesized aperture focusing technology (SAFT). A low cost ultrasonic sensor array consisting of 12 market available low frequency ultrasonic transducers is designed and manufactured. A channel compensation method is proposed to improve the consistency of different transducers. The controlling devices for array scan as well as the virtual instrument for SAFT imaging are designed. In the coarse scan mode with the scan step of 50 mm, the system can quickly give an image display of a cross section of 600 mm (L) × 300 mm (D) by one measurement. In the refined scan model, the system can reduce the scan step and give an image display of the same cross section by moving the sensor array several times. Experiments on staircase specimen, concrete slab with embedded target, and building floor with underground pipe line all verify the efficiency of the proposed method.

WRAP-RIB antenna technology development

NASA Technical Reports Server (NTRS)

Freeland, R. E.; Garcia, N. F.; Iwamoto, H.

1985-01-01

The wrap-rib deployable antenna concept development is based on a combination of hardware development and testing along with extensive supporting analysis. The proof-of-concept hardware models are large in size so they will address the same basic problems associated with the design fabrication, assembly and test as the full-scale systems which were selected to be 100 meters at the beginning of the program. The hardware evaluation program consists of functional performance tests, design verification tests and analytical model verification tests. Functional testing consists of kinematic deployment, mesh management and verification of mechanical packaging efficiencies. Design verification consists of rib contour precision measurement, rib cross-section variation evaluation, rib materials characterizations and manufacturing imperfections assessment. Analytical model verification and refinement include mesh stiffness measurement, rib static and dynamic testing, mass measurement, and rib cross-section characterization. This concept was considered for a number of potential applications that include mobile communications, VLBI, and aircraft surveillance. In fact, baseline system configurations were developed by JPL, using the appropriate wrap-rib antenna, for all three classes of applications.

Suspended liquid subtractive lithography: printing three dimensional channels directly into uncured PDMS

NASA Astrophysics Data System (ADS)

Helmer, D.; Voigt, A.; Wagner, S.; Keller, N.; Sachsenheimer, K.; Kotz, F.; Nargang, T. M.; Rapp, B. E.

2018-02-01

Polydimethylsiloxane (PDMS) is one of the most widely used polymers for the generation of microfluidic chips. The standard procedures of soft lithography require the formation of a new master structure for every design which is timeconsuming and expensive. All channel generated by soft lithography need to be consecutively sealed by bonding which is a process that can proof to be hard to control. Channel cross-sections are largely restricted to squares or flat-topped designs and the generation of truly three-dimensional designs is not straightforward. Here we present Suspended Liquid Subtractive Lithography (SLSL) a method for generating microfluidic channels of nearly arbitrary three-dimensional structures in PDMS that do not require master formation or bonding and give circular channel cross sections which are especially interesting for mimicking in vivo environments. In SLSL, an immiscible liquid is introduced into the uncured PDMS by a capillary mounted on a 3D printer head. The liquid forms continuous "threads" inside the matrix thus creating void suspended channel structures.

Anatomy-driven design of a prototype video laryngoscope for extremely low birth weight infants

NASA Astrophysics Data System (ADS)

Baker, Katherine; Tremblay, Eric; Karp, Jason; Ford, Joseph; Finer, Neil; Rich, Wade

2010-11-01

Extremely low birth weight (ELBW) infants frequently require endotracheal intubation for assisted ventilation or as a route for administration of drugs or exogenous surfactant. In adults and less premature infants, the risks of this intubation can be greatly reduced using video laryngoscopy, but current products are too large and incorrectly shaped to visualize an ELBW infant's airway anatomy. We design and prototype a video laryngoscope using a miniature camera set in a curved acrylic blade with a 3×6-mm cross section at the tip. The blade provides a mechanical structure for stabilizing the tongue and acts as a light guide for an LED light source, located remotely to avoid excessive local heating at the tip. The prototype is tested on an infant manikin and found to provide sufficient image quality and mechanical properties to facilitate intubation. Finally, we show a design for a neonate laryngoscope incorporating a wafer-level microcamera that further reduces the tip cross section and offers the potential for low cost manufacture.

Design study of beam position monitors for measuring second-order moments of charged particle beams

NASA Astrophysics Data System (ADS)

Yanagida, Kenichi; Suzuki, Shinsuke; Hanaki, Hirofumi

2012-01-01

This paper presents a theoretical investigation on the multipole moments of charged particle beams in two-dimensional polar coordinates. The theoretical description of multipole moments is based on a single-particle system that is expanded to a multiparticle system by superposition, i.e., summing over all single-particle results. This paper also presents an analysis and design method for a beam position monitor (BPM) that detects higher-order (multipole) moments of a charged particle beam. To calculate the electric fields, a numerical analysis based on the finite difference method was created and carried out. Validity of the numerical analysis was proven by comparing the numerical with the analytical results for a BPM with circular cross section. Six-electrode BPMs with circular and elliptical cross sections were designed for the SPring-8 linac. The results of the numerical calculations show that the second-order moment can be detected for beam sizes ≧420μm (circular) and ≧550μm (elliptical).

SEISMIC RESPONSE OF DAM WITH SOIL-STRUCTURE INTERACTION.

USGS Publications Warehouse

Bycroft, G.N.; Mork, P.N.

1987-01-01

An analytical solution to the response of a long trapezoidal-section dam on a foundation consisting of an elastic half-space and subjected to simulated earthquake motion is developed. An optimum seismic design is achieved when the cross section of the dam is triangular. The effect of soil structure interaction is to lower the strain occurring in the dam.

Computational Investigations in Rectangular Convergent and Divergent Ribbed Channels

NASA Astrophysics Data System (ADS)

Sivakumar, Karthikeyan; Kulasekharan, N.; Natarajan, E.

2018-05-01

Computational investigations on the rib turbulated flow inside a convergent and divergent rectangular channel with square ribs of different rib heights and different Reynolds numbers (Re=20,000, 40,000 and 60,000). The ribs were arranged in a staggered fashion between the upper and lower surfaces of the test section. Computational investigations are carried out using computational fluid dynamic software ANSYS Fluent 14.0. Suitable solver settings like turbulence models were identified from the literature and the boundary conditions for the simulations on a solution of independent grid. Computations were carried out for both convergent and divergent channels with 0 (smooth duct), 1.5, 3, 6, 9 and 12 mm rib heights, to identify the ribbed channel with optimal performance, assessed using a thermo hydraulic performance parameter. The convergent and divergent rectangular channels show higher Nu values than the standard correlation values.

Influence of fibre design and curvature on crosstalk in multi-core fibre

NASA Astrophysics Data System (ADS)

Egorova, O. N.; Astapovich, M. S.; Melnikov, L. A.; Salganskii, M. Yu; Mishkin, V. P.; Nishchev, K. N.; Semjonov, S. L.; Dianov, E. M.

2016-03-01

We have studied the influence of cross-sectional structure and bends on optical cross-talk in a multicore fibre. A reduced refractive index layer produced between the cores of such fibre with a small centre-to-centre spacing between neighbouring cores (27 μm) reduces optical cross-talk by 20 dB. The cross-talk level achieved, 30 dB per kilometre of the length of the multicore fibre, is acceptable for a number of applications where relatively small lengths of fibre are needed. Moreover, a significant decrease in optical cross-talk has been ensured by reducing the winding diameter of multicore fibres with identical cores.

Non-traditional shape GFRP rebars for concrete reinforcement

NASA Astrophysics Data System (ADS)

Claure, Guillermo G.

The use of glass-fiber-reinforced-polymer (GFRP) composites as internal reinforcement (rebars) for concrete structures has proven to be an alternative to traditional steel reinforcement due to significant advantages such as magnetic transparency and, most importantly, corrosion resistance equating to durability and structural life extension. In recent years, the number of projects specifying GFRP reinforcement has increased dramatically leading the construction industry towards more sustainable practices. Typically, GFRP rebars are similar to their steel counterparts having external deformations or surface enhancements designed to develop bond to concrete, as well as having solid circular cross-sections; but lately, the worldwide composites industry has taken advantage of the pultrusion process developing GFRP rebars with non-traditional cross-sectional shapes destined to optimize their mechanical, physical, and environmental attributes. Recently, circular GFRP rebars with a hollow-core have also become available. They offer advantages such as a larger surface area for improved bond, and the use of the effective cross-sectional area that is engaged to carry load since fibers at the center of a solid cross-section are generally not fully engaged. For a complete understanding of GFRP rebar physical properties, a study on material characterization regarding a quantitative cross-sectional area analysis of different GFRP rebars was undertaken with a sample population of 190 GFRP specimens with rebar denomination ranging from #2 to #6 and with different cross-sectional shapes and surface deformations manufactured by five pultruders from around the world. The water displacement method was applied as a feasible and reliable way to conduct the investigation. In addition to developing a repeatable protocol for measuring cross-sectional area, the objectives of establishing critical statistical information related to the test methodology and recommending improvements to existing provisions and standards allowing for a consistent universal norm for all GFRP rebars were reached. This dissertation also presents an evaluation of the structural behavior of reinforced concrete (RC) beams and slabs using the new type of GFRP rebar consisting of a non-traditional hollow-core shape compared to "traditional" solid round rebars with equivalent cross-sectional areas within the framework of two studies, respectively. To validate the design assumptions following ACI 440.1R design guidelines, two conditions were investigated: under-reinforced (failure controlled by rupture of GFRP rebar); and, over-reinforced (failure controlled by crushing of concrete). For comparison, a cyclic three-point bending load test matrix was developed: for beams, 3 under-reinforced and 3 over-reinforced with hollow-core and solid GFRP rebars, respectively, making a total of 12 RC specimens; for slabs, 3 under-reinforced and 3 over-reinforced with hollow-core and 2 types of solid GFRP rebars, respectively, making a total of 18 RC slabs. The studies on GFRP RC beams and slabs concluded that the hollow-core GFRP rebars were as effective as their solid counterpart and ACI 440.1R design guidelines were applicable to predict their performance. It was shown that final design may be controlled by the permissible deflections as governing parameter for elements under service conditions. Also, a final study with a test matrix containing six extra specimens was generated for post-fire residual strength evaluation of fire-exposed GFRP RC slabs along with temperature gradient in the slabs and dynamic mechanical analysis (DMA) investigation on GFRP samples extracted from the fire-exposed slabs. In this study, the ability of GFRP RC slabs to retain structural integrity during a standards fire exposure as well as determining the residual structural capacity were investigated. The residual strength evaluation of the fire-exposed slabs showed a range of results varying between +/- 10%, of the virgin slabs. And, 19 mm (0.75 in.) cover with normal weight concrete was shown to be adequate to provide the necessary fire protection to the GFRP rebars preventing irreversible damage for two-hour fire rated GFRP RC slabs subjected to service loads; also, from the DMA and glass transition temperature of samples extracted from the GFRP rebars, it is inferred that the resin had undergone a post curing phase.

An Integrated Optimization Design Method Based on Surrogate Modeling Applied to Diverging Duct Design

NASA Astrophysics Data System (ADS)

Hanan, Lu; Qiushi, Li; Shaobin, Li

2016-12-01

This paper presents an integrated optimization design method in which uniform design, response surface methodology and genetic algorithm are used in combination. In detail, uniform design is used to select the experimental sampling points in the experimental domain and the system performance is evaluated by means of computational fluid dynamics to construct a database. After that, response surface methodology is employed to generate a surrogate mathematical model relating the optimization objective and the design variables. Subsequently, genetic algorithm is adopted and applied to the surrogate model to acquire the optimal solution in the case of satisfying some constraints. The method has been applied to the optimization design of an axisymmetric diverging duct, dealing with three design variables including one qualitative variable and two quantitative variables. The method of modeling and optimization design performs well in improving the duct aerodynamic performance and can be also applied to wider fields of mechanical design and seen as a useful tool for engineering designers, by reducing the design time and computation consumption.

Research design and statistical methods in Pakistan Journal of Medical Sciences (PJMS).

PubMed

Akhtar, Sohail; Shah, Syed Wadood Ali; Rafiq, M; Khan, Ajmal

2016-01-01

This article compares the study design and statistical methods used in 2005, 2010 and 2015 of Pakistan Journal of Medical Sciences (PJMS). Only original articles of PJMS were considered for the analysis. The articles were carefully reviewed for statistical methods and designs, and then recorded accordingly. The frequency of each statistical method and research design was estimated and compared with previous years. A total of 429 articles were evaluated (n=74 in 2005, n=179 in 2010, n=176 in 2015) in which 171 (40%) were cross-sectional and 116 (27%) were prospective study designs. A verity of statistical methods were found in the analysis. The most frequent methods include: descriptive statistics (n=315, 73.4%), chi-square/Fisher's exact tests (n=205, 47.8%) and student t-test (n=186, 43.4%). There was a significant increase in the use of statistical methods over time period: t-test, chi-square/Fisher's exact test, logistic regression, epidemiological statistics, and non-parametric tests. This study shows that a diverse variety of statistical methods have been used in the research articles of PJMS and frequency improved from 2005 to 2015. However, descriptive statistics was the most frequent method of statistical analysis in the published articles while cross-sectional study design was common study design.

The Development of Cambered Airfoil Sections Having Favorable Lift Characteristics at Supercritical Mach Numbers

NASA Technical Reports Server (NTRS)

Graham, Donald J

1948-01-01

Several groups of new airfoil sections, designated as the NACA 8-series, are derived analytically to have lift characteristics at supercritical Mach numbers which are favorable in the sense that the abrupt loss of lift, characteristic of the usual airfoil section at Mach numbers above the critical, is avoided. Aerodynamic characteristics determined, from two-dimensional windtunnel tests at Mach numbers up to approximately 0.9 are presented for each of the derived airfoils. Comparisons are made between the characteristics of these airfoils and the corresponding characteristics of representative NPiCA 6-series airfoils. The experimental results confirm the design expectations in demonstrating for the NACA S-series airfoils either no variation, or an Increase from the low-speed design value, In the lift coefficient at a constant angle of attack with increasing Mach number above the critical. It was not found possible to improve the variation with Mach number of the slope of the lift curve for these airfoils above that for the NACA 6-series airfoils. The drag characteristics of the new airfoils are somewhat inferior to those of the NACA 6- series with respect to divergence with Mach number, but the pitching-moment characteristics are more favorable for the thinner new sections In demonstrating somewhat smaller variations of moment coefficient with both angle of attack and Mach number. The effect on the aero&ynamic characteristics at high Mach numbers of removing the cusp from the trailing-edge regions of two 10-percent-chord-thick NACA 6-series airfoils is determined to be negligible.

A supersonic jet target for the cross section measurement of the 12C(α, γ)16O reaction with the recoil mass separator ERNA

NASA Astrophysics Data System (ADS)

Rapagnani, D.; Buompane, R.; Di Leva, A.; Gialanella, L.; Busso, M.; De Cesare, M.; De Stefano, G.; Duarte, J. G.; Gasques, L. R.; Morales Gallegos, L.; Palmerini, S.; Romoli, M.; Tufariello, F.

2017-09-01

12C(α, γ)16O cross section plays a key-role in the stellar evolution and nucleosynthesis of massive stars. Hence, it must be determined with the precision of about 10% at the relevant Gamow energy of 300 keV. The ERNA (European Recoil mass separator for Nuclear Astrophysics) collaboration measured, for the first time, the total cross section of 12C(α, γ)16O by means of the direct detection of the 16O ions produced in the reaction down to an energy of Ecm = 1.9 MeV. To extend the measurement at lower energy, it is necessary to limit the extension of the He gas target. This can be achieved using a supersonic jet, where the oblique shock waves and expansion fans formed at its boundaries confine the gas, which can be efficiently collected using a catcher. A test version of such a system has been designed, constructed and experimentally characterized as a bench mark for a full numerical simulation using FV (Finite Volume) methods. The results of the commissioning of the jet test version and the design of the new system that will be used in combination with ERNA are presented and discussed.

Reprint of: A supersonic jet target for the cross section measurement of the 12C(α, γ)16O reaction with the recoil mass separator ERNA

NASA Astrophysics Data System (ADS)

Rapagnani, D.; Buompane, R.; Di Leva, A.; Gialanella, L.; Busso, M.; De Cesare, M.; De Stefano, G.; Duarte, J. G.; Gasques, L. R.; Morales Gallegos, L.; Palmerini, S.; Romoli, M.; Tufariello, F.

2018-01-01

12C(α, γ)16O cross section plays a key-role in the stellar evolution and nucleosynthesis of massive stars. Hence, it must be determined with the precision of about 10% at the relevant Gamow energy of 300 keV. The ERNA (European Recoil mass separator for Nuclear Astrophysics) collaboration measured, for the first time, the total cross section of 12C(α, γ)16O by means of the direct detection of the 16O ions produced in the reaction down to an energy of Ecm = 1.9 MeV. To extend the measurement at lower energy, it is necessary to limit the extension of the He gas target. This can be achieved using a supersonic jet, where the oblique shock waves and expansion fans formed at its boundaries confine the gas, which can be efficiently collected using a catcher. A test version of such a system has been designed, constructed and experimentally characterized as a bench mark for a full numerical simulation using FV (Finite Volume) methods. The results of the commissioning of the jet test version and the design of the new system that will be used in combination with ERNA are presented and discussed.