Thermally induced magnonic spin current, thermomagnonic torques, and domain-wall dynamics in the presence of Dzyaloshinskii-Moriya interaction

NASA Astrophysics Data System (ADS)

Wang, X.-G.; Chotorlishvili, L.; Guo, G.-H.; Sukhov, A.; Dugaev, V.; Barnaś, J.; Berakdar, J.

2016-09-01

Thermally activated domain-wall (DW) motion in magnetic insulators has been considered theoretically, with a particular focus on the role of Dzyaloshinskii-Moriya interaction (DMI) and thermomagnonic torques. The thermally assisted DW motion is a consequence of the magnonic spin current due to the applied thermal bias. In addition to the exchange magnonic spin current and the exchange adiabatic and the entropic spin transfer torques, we also consider the DMI-induced magnonic spin current, thermomagnonic DMI fieldlike torque, and the DMI entropic torque. Analytical estimations are supported by numerical calculations. We found that the DMI has a substantial influence on the size and the geometry of DWs, and that the DWs become oriented parallel to the long axis of the nanostrip. Increasing the temperature smoothes the DWs. Moreover, the thermally induced magnonic current generates a torque on the DWs, which is responsible for their motion. From our analysis it follows that for a large enough DMI the influence of DMI-induced fieldlike torque is much stronger than that of the DMI and the exchange entropic torques. By manipulating the strength of the DMI constant, one can control the speed of the DW motion, and the direction of the DW motion can be switched, as well. We also found that DMI not only contributes to the total magnonic current, but also it modifies the exchange magnonic spin current, and this modification depends on the orientation of the steady-state magnetization. The observed phenomenon can be utilized in spin caloritronics devices, for example in the DMI based thermal diodes. By switching the magnetization direction, one can rectify the total magnonic spin current.

Reduction in the latency of action of antidepressants by 17 beta-estradiol in the forced swimming test.

PubMed

Estrada-Camarena, E; Rivera, N M Vega; Berlanga, C; Fernández-Guasti, A

2008-12-01

Antidepressants (ADs) are slow to produce their therapeutic effect. This long latency promotes the development of new strategies to short their onset of action. Previous reports indicated that 17beta-estradiol (E(2)) promotes the antidepressant-like activity of fluoxetine (FLX) and desipramine (DMI) in the forced swimming test (FST). The aim of the present work was to analyze if E(2) reduces the antidepressant-like onset of action of venlafaxine (VLX), FLX, and DMI. Independent groups of ovariectomized female Wistar rats were tested in the FST and in the open field after chronic (1 to 14 days) treatment with VLX (20 mg/kg/day), FLX (1.25 mg/kg/day), or DMI (1.25 mg/kg/day) alone or in combination with a single injection of E(2) (2.5 microg/rat sc, 8 h before FST). VLX, FLX, or DMI by themselves at these doses did not induce changes in the FST at short intervals after their injection (from 1 to 7 days). The addition of E(2) promoted the antidepressant-like effect of VLX and DMI as early as day 1. Such action was also evident after 3, for FLX, and 14 days for both FLX and DMI, but not for VLX. The behavioral actions of these ADs combined with E(2) were not accompanied by increases in general activity in the open-field test. E(2) clearly reduced the latency to the onset of action for these ADs in the FST. These results represent an interesting therapeutic strategy for the treatment of depression in perimenopausal women.

Unraveling the inhibitory effect of dihydromyricetin on heterocyclic aromatic amines formation.

PubMed

Zhou, Bin; Zhao, Yueliang; Wang, Xichang; Fan, Daming; Cheng, Kawing; Wang, Mingfu

2018-03-01

Heterocyclic aromatic amines (HAAs) are mutagens and rodent carcinogens. Flavonoids have attracted considerable attention for development into effective inhibitors against the formation of genotoxic HAAs in thermally processed foods. The inhibitory effect of dihydromyricetin (DMY) on the formation of key HAAs, including 2-amino-1-methyl-6-phenylimidazo[4,5-b]pyridine (PhIP), 2-amino-3,8-dimethylimidazo[4,5-f]-quinoxaline (MeIQx), and 2-amino-3,4,8-trimethylimidazo[4,5-f]quinoxaline (4,8-DiMeIQx), was significant. In chemical models, DMY (0.05 mmol, 0.1 mmol, and 0.2 mmol) significantly decreased the amount of PhIP formed (43.0%, 54.7%, and 75.7% respectively). A significant inhibitory effect on the formation of MeIQx and 4,8-DiMeIQx was also observed. Moreover, DMY (0.05%, 0.1%, and 0.2%) reduced the generation of PhIP (by 48.0%, 59.0%, and 80.1% respectively) and that of MeIQx (by 45.8%, 62.0%, and 76.7% respectively) in fried beef patties. The results indicate that DMY could be converted into myricetin during thermal processing, and both DMY and myricetin could trap phenylacetaldehyde, a major Strecker aldehyde of phenylalanine, in a similar manner to thus inhibit the generation of PhIP. This study provides valuable information for the development of effective strategies to minimize HAA content in thermally processed foods and also sheds light on the mechanism that accounts for the inhibitory effect. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Evolution of DMY, a newly emergent male sex-determination gene of medaka fish.

PubMed

Zhang, Jianzhi

2004-04-01

The Japanese medaka fish Oryzias latipes has an XX/XY sex-determination system. The Y-linked sex-determination gene DMY is a duplicate of the autosomal gene DMRT1, which encodes a DM-domain-containing transcriptional factor. DMY appears to have originated recently within Oryzias, allowing a detailed evolutionary study of the initial steps that led to the new gene and new sex-determination system. Here I analyze the publicly available DMRT1 and DMY gene sequences of Oryzias species and report the following findings. First, the synonymous substitution rate in DMY is 1.73 times that in DMRT1, consistent with the male-driven evolution hypothesis. Second, the ratio of the rate of nonsynonymous nucleotide substitution (d(N)) to that of synonymous substitution (d(S)) is significantly higher in DMY than in DMRT1. Third, in DMRT1, the d(N)/d(S) ratio for the DM domain is lower than that for non-DM regions, as expected from the functional importance of the DM domain. But in DMY, the opposite is observed and the DM domain is likely under positive Darwinian selection. Fourth, only one characteristic amino acid distinguishes all DMY sequences from all DMRT1 sequences, suggesting that a single amino acid change may be largely responsible for the establishment of DMY as the male sex-determination gene in medaka fish.

Hierarchical Bayesian inference on genetic and non-genetic components of partial efficiencies determining feed efficiency in dairy cattle

USDA-ARS?s Scientific Manuscript database

Dairy cattle feed efficiency (FE) can be defined as the ability to convert DMI into milk energy (MILKE) and maintenance or metabolic body weight (MBW). In other words, DMI is conditional on MILKE and MBW (DMI|MILKE,MBW). These partial regressions or partial efficiencies (PE) of DMI on MILKE and MBW ...

Desipramine restricts estral cycle oscillations in swimming.

PubMed

Contreras, C M; Martínez-Mota, L; Saavedra, M

1998-10-01

1. Desipramine (DMI) is a tricyclic antidepressant which reduces the immobility in rats forced to swim; however, it is unknown whether estral cycle phases impinge on DMI actions on immobility in daily swimming tests during several weeks. 2. In female wistar rats, vaginal smears taken before testing defined four estral phases. Afterwards, the authors assessed the latency for the first period of immobility in five-min forced swim tests practiced on 21-day DMI (DMI group), 21-day washout saline given after a 21-day DMI treatment (washout-saline group), or non-treated rats (control group). 3. We observed a longer latency for the first period of immobility in proestrus-estrus from the control and washout-saline groups. The 21-day treatment with DMI (2.1 mg/kg i.p., once a day) significantly (p < 0.001) increased the latency by about 160% from control regardless of the estral cycle phase. 4. It is concluded that proestrus-estrus relates to increased struggling behavior. DMI enhances struggling behavior independently of hormonal state.

A Dzyaloshinskii-Moriya Anisotropy in nanomagnets with in-plane magnetization

NASA Astrophysics Data System (ADS)

Cubukcu, M.; Sampaio, J.; Khvalkovskiy, A. V.; Apalkov, D.; Cros, V.; Reyren, N.

The Dzyaloshinskii-Moriya interaction (DMI) is known to be a direct manifestation of spin-orbit coupling in systems with broken inversion symmetry. We present a new anisotropy for in-plane-magnetized nanomagnets which is due to the interfacial DMI. This new anisotropy depends on the shape of the magnet, and is perpendicular to the demagnetization shape anisotropy. The DMI anisotropy term that we introduce here results from the DMI energy reduction due to an out-of-plane tilt of the spins at the edges that are oriented perpendicular to the magnetization. For large enough DMI, the reduction of the DMI and anisotropy energies takes over the demagnetization energy cost when magnetization lies along the minor axis of a structure. Our experimental, numerical and analytical results demonstrate this prediction in magnets of elongated shape for small enough volume (and thus quasi-uniform magnetization). Our results also provide the first experimental evidence of the interfacial DMI-induced tilt of the spins at the borders. This work was supported by the Samsung Global MRAM Innovation Program.

Desipramine increases cardiac parasympathetic activity via α2-adrenergic mechanism in rats.

PubMed

Kawada, Toru; Akiyama, Tsuyoshi; Shimizu, Shuji; Fukumitsu, Masafumi; Kamiya, Atsunori; Sugimachi, Masaru

2017-07-01

Desipramine (DMI) is a blocker of neuronal norepinephrine (NE) uptake transporter. Although intravenous DMI has been shown to cause centrally-mediated sympathoinhibition and peripheral NE accumulation, its parasympathetic effect remains to be elucidated. We hypothesized that intravenous DMI activates the cardiac vagal nerve via an α 2 -adrenergic mechanism. Using a cardiac microdialysis technique, changes in myocardial interstitial acetylcholine (ACh) levels in the left ventricular free wall in response to intravenous DMI (1mg·kg -1 ) were examined in anesthetized rats. In rats with intact vagi (n=7), intravenous DMI increased ACh from 1.67±0.43 to 2.48±0.66nM (P<0.01). In rats with vagotomy (n=5), DMI did not significantly change ACh (from 0.92±0.16 to 0.85±0.23nM). In rats with intact vagi pretreated with intravenous yohimbine (2mg·kg -1 ), DMI did not significantly change ACh (from 1.25±0.23 to 1.13±0.15nM). In conclusion, while DMI is generally considered to be an agent that predominantly affects sympathetic neurotransmission, it can activate the cardiac vagal nerve via α 2 -adrenergic stimulation in experimental settings in vivo. Copyright © 2017 Elsevier B.V. All rights reserved.

Diabetic muscle infarction in end-stage renal disease: A scoping review on epidemiology, diagnosis and treatment

PubMed Central

Yong, Tuck Yean; Khow, Kareeann Sok Fun

2018-01-01

Diabetic muscle infarction (DMI) refers to spontaneous ischemic necrosis of skeletal muscle among people with diabetes mellitus, unrelated to arterial occlusion. People with DMI may have coexisting end-stage renal disease (ESRD) but little is known about its epidemiology and clinical outcomes in this setting. This scoping review seeks to investigate the characteristics, clinical features, diagnostic evaluation, management and outcomes of DMI among people with ESRD. Electronic database (PubMed/MEDLINE, CINAHL, SCOPUS and EMBASE) searches were conducted for (“diabetic muscle infarction” or “diabetic myonecrosis”) and (“chronic kidney disease” or “renal impairment” or “dialysis” or “renal replacement therapy” or “kidney transplant”) from January 1980 to June 2017. Relevant cases from reviewed bibliographies in reports retrieved were also included. Data were extracted in a standardized form. A total of 24 publications with 41 patients who have ESRD were included. The mean age at the time of presentation with DMI was 44.2 years. Type 2 diabetes was present in 53.7% of patients while type 1 in 41.5%. In this cohort, 60.1% were receiving hemodialysis, 21% on peritoneal dialysis and 12.2% had kidney transplantation. The proximal lower limb musculature was the most commonly affected site. Muscle pain and swelling were the most frequent manifestation on presentation. Magnetic resonance imaging (MRI) provided the most specific findings for DMI. Laboratory investigation findings are usually non-specific. Non-surgical therapy is usually used in the management of DMI. Short-term prognosis of DMI is good but recurrence occurred in 43.9%. DMI is an uncommon complication in patients with diabetes mellitus, including those affected by ESRD. In comparison with unselected patients with DMI, the characteristics and outcomes of those with ESRD are generally similar. DMI may also occur in kidney transplant recipients, including pancreas-kidney transplantation. MRI is the most useful diagnostic investigation. Non-surgical treatment involving analgesia, optimization of glycemic control and initial bed rest can help to improve recovery rate. However, recurrence of DMI is relatively frequent. PMID:29527509

Desipramine induces disorder in cholesterol-rich membranes: implications for viral trafficking

NASA Astrophysics Data System (ADS)

Pakkanen, Kirsi; Salonen, Emppu; Mäkelä, Anna R.; Oker-Blom, Christian; Vattulainen, Ilpo; Vuento, Matti

2009-12-01

In this study, the effect of desipramine (DMI) on phospholipid bilayers and parvoviral entry was elucidated. In atomistic molecular dynamics simulations, DMI was found to introduce disorder in cholesterol-rich phospholipid bilayers. This was manifested by a decrease in the deuterium order parameter SCD as well as an increase in the membrane area. Disordering of the membrane suggested DMI to destabilize cholesterol-rich membrane domains (rafts) in cellular conditions. To relate the raft disrupting ability of DMI with novel biological relevance, we studied the intracellular effect of DMI using canine parvovirus (CPV), a virus known to interact with endosomal membranes and sphingomyelin, as an intracellular probe. DMI was found to cause retention of the virus in intracellular vesicular structures leading to the inhibition of viral proliferation. This implies that DMI has a deleterious effect on the viral traffic. As recycling endosomes and the internal vesicles of multivesicular bodies are known to contain raft components, the effect of desipramine beyond the plasma membrane step could be caused by raft disruption leading to impaired endosomal function and possibly have direct influence on the penetration of the virus through an endosomal membrane.

Association of lameness with milk yield and lactation curves in Chios dairy ewes.

PubMed

Gelasakis, Athanasios I; Arsenos, Georgios; Valergakis, Georgios E; Banos, Georgios

2015-05-01

The objective of the study was twofold: (i) to quantify the differences in daily milk yield (DMY) and total milk yield (TMY) between lame and non-lame dairy ewes and (ii) to determine the shape of lactation curves around the lameness incident. The overall study was a prospective study of lameness for the surveyed sheep population, with a nested study including the selection of matching controls for each lame ewe separately. Two intensively reared flocks of purebred Chios ewes and a total of 283 ewes were used. Data, including gait assessment and DMY records, were collected on a weekly basis during on-farm visits across the milking period. A general linear model was developed for the calculation of lactation curves of lame and non-lame ewes, whereas one-way ANOVA was used for the comparisons between lame ewes and their controls. Lameness incidence was 12.4 and 16.8% on Farms A and B, respectively. Average DMY in lame ewes was significantly lower (213.8 g, P < 0.001) compared with the rest of the flock, where DMY averaged 1.340 g. The highest DMY reduction in lame ewes was observed during the week 16 of the milking period (P < 0.001), whereas the reduction of DMY, for lame ewes, remained significant at P < 0.001 level from week 8 to week 28 of milking. Comparisons between lame and controls revealed that at the week of lameness diagnosis a significant DMY reduction (P ≤ 0.001) was observed in lame ewes (about 32.5%), which was maximised 1 week later (35.8%, P ≤ 0.001) and continued for several weeks after recovery, resulting in 19.3% lower TMY for lame ewes for the first 210 d of the milking period (P < 0.01). Moreover, at flock level, TMY for non-lame and lame ewes, as calculated by the general linear model, was 318.9 and 268.0 kg, respectively. The results of this study demonstrate evidence of significant financial losses in dairy sheep due to lameness which, however, need to be accurately estimated in further, more detailed, analyses.

Effects of spatially engineered Dzyaloshinskii-Moriya interaction in ferromagnetic films

NASA Astrophysics Data System (ADS)

Mulkers, Jeroen; Van Waeyenberge, Bartel; Milošević, Milorad V.

2017-04-01

The Dzyaloshinskii-Moriya interaction (DMI) is a chiral interaction that favors formation of domain walls. Recent experiments and ab initio calculations show that there are multiple ways to modify the strength of the interfacially induced DMI in thin ferromagnetic films with perpendicular magnetic anisotropy. In this paper we reveal theoretically the effects of spatially varied DMI on the magnetic state in thin films. In such heterochiral 2D structures we report several emergent phenomena, ranging from the equilibrium spin canting at the interface between regions with different DMI, over particularly strong confinement of domain walls and skyrmions within high-DMI tracks, to advanced applications such as domain tailoring nearly at will, design of magnonic waveguides, and much improved skyrmion racetrack memory.

Interfacial Dzyaloshinskii-Moriya Interaction: Effect of 5 d Band Filling and Correlation with Spin Mixing Conductance

NASA Astrophysics Data System (ADS)

Ma, Xin; Yu, Guoqiang; Tang, Chi; Li, Xiang; He, Congli; Shi, Jing; Wang, Kang L.; Li, Xiaoqin

2018-04-01

The Dzyaloshinskii-Moriya interaction (DMI) at the heavy metal (HM) and ferromagnetic metal (FM) interface has been recognized as a key ingredient in spintronic applications. Here we investigate the chemical trend of DMI on the 5 d band filling (5 d3- 5 d10 ) of the HM element in HM/FM (FM =CoFeB ,Co )/MgO multilayer thin films. DMI is quantitatively evaluated by measuring asymmetric spin wave dispersion using Brillouin light scattering. Sign reversal and 20 times modification of the DMI coefficient D have been measured as the 5 d HM element is varied. The chemical trend can be qualitatively understood by considering the 5 d and 3 d bands alignment at the HM/FM interface and the subsequent orbital hybridization around the Fermi level. Furthermore, a correlation is observed between DMI and effective spin mixing conductance at the HM/FM interfaces. Our results provide new insights into the interfacial DMI for designing future spintronic devices.

All-Electrical Measurement of Interfacial Dzyaloshinskii-Moriya Interaction Using Collective Spin-Wave Dynamics.

PubMed

Lee, Jong Min; Jang, Chaun; Min, Byoung-Chul; Lee, Seo-Won; Lee, Kyung-Jin; Chang, Joonyeon

2016-01-13

Dzyaloshinskii-Moriya interaction (DMI), which arises from the broken inversion symmetry and spin-orbit coupling, is of prime interest as it leads to a stabilization of chiral magnetic order and provides an efficient manipulation of magnetic nanostructures. Here, we report all-electrical measurement of DMI using propagating spin wave spectroscopy based on the collective spin wave with a well-defined wave vector. We observe a substantial frequency shift of spin waves depending on the spin chirality in Pt/Co/MgO structures. After subtracting the contribution from other sources to the frequency shift, it is possible to quantify the DMI energy in Pt/Co/MgO systems. The result reveals that the DMI in Pt/Co/MgO originates from the interfaces, and the sign of DMI corresponds to the inversion asymmetry of the film structures. The electrical excitation and detection of spin waves and the influence of interfacial DMI on the collective spin-wave dynamics will pave the way to the emerging field of spin-wave logic devices.

Genetic parameters across lactation for feed intake, fat- and protein-corrected milk, and liveweight in first-parity Holstein cattle.

PubMed

Manzanilla Pech, C I V; Veerkamp, R F; Calus, M P L; Zom, R; van Knegsel, A; Pryce, J E; De Haas, Y

2014-09-01

Breeding values for dry matter intake (DMI) are important to optimize dairy cattle breeding goals for feed efficiency. However, generally, only small data sets are available for feed intake, due to the cost and difficulty of measuring DMI, which makes understanding the genetic associations between traits across lactation difficult, let alone the possibility for selection of breeding animals. However, estimating national breeding values through cheaper and more easily measured correlated traits, such as milk yield and liveweight (LW), could be a first step to predict DMI. Combining DMI data across historical nutritional experiments might help to expand the data sets. Therefore, the objective was to estimate genetic parameters for DMI, fat- and protein-corrected milk (FPCM) yield, and LW across the entire first lactation using a relatively large data set combining experimental data across the Netherlands. A total of 30,483 weekly records for DMI, 49,977 for FPCM yield, and 31,956 for LW were available from 2,283 Dutch Holstein-Friesian first-parity cows between 1990 and 2011. Heritabilities, covariance components, and genetic correlations were estimated using a multivariate random regression model. The model included an effect for year-season of calving, and polynomials for age of cow at calving and days in milk (DIM). The random effects were experimental treatment, year-month of measurement, and the additive genetic, permanent environmental, and residual term. Additive genetic and permanent environmental effects were modeled using a third-order orthogonal polynomial. Estimated heritabilities ranged from 0.21 to 0.40 for DMI, from 0.20 to 0.43 for FPCM yield, and from 0.25 to 0.48 for LW across DIM. Genetic correlations between DMI at different DIM were relatively low during early and late lactation, compared with mid lactation. The genetic correlations between DMI and FPCM yield varied across DIM. This correlation was negative (up to -0.5) between FPCM yield in early lactation and DMI across the entire lactation, but highly positive (above 0.8) when both traits were in mid lactation. The correlation between DMI and LW was 0.6 during early lactation, but decreased to 0.4 during mid lactation. The highest correlations between FPCM yield and LW (0.3-0.5) were estimated during mid lactation. However, the genetic correlations between DMI and either FPCM yield or LW were not symmetric across DIM, and differed depending on which trait was measured first. The results of our study are useful to understand the genetic relationship of DMI, FPCM yield, and LW on specific days across lactation. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The Recent Evolution of a Symbiotic Ion Channel in the Legume Family Altered Ion Conductance and Improved Functionality in Calcium Signaling[C][W

PubMed Central

Venkateshwaran, Muthusubramanian; Cosme, Ana; Han, Lu; Banba, Mari; Satyshur, Kenneth A.; Schleiff, Enrico; Parniske, Martin; Imaizumi-Anraku, Haruko; Ané, Jean-Michel

2012-01-01

Arbuscular mycorrhiza and the rhizobia-legume symbiosis are two major root endosymbioses that facilitate plant nutrition. In Lotus japonicus, two symbiotic cation channels, CASTOR and POLLUX, are indispensable for the induction of nuclear calcium spiking, one of the earliest plant responses to symbiotic partner recognition. During recent evolution, a single amino acid substitution in DOES NOT MAKE INFECTIONS1 (DMI1), the POLLUX putative ortholog in the closely related Medicago truncatula, rendered the channel solo sufficient for symbiosis; castor, pollux, and castor pollux double mutants of L. japonicus were rescued by DMI1 alone, while both Lj-CASTOR and Lj-POLLUX were required for rescuing a dmi1 mutant of M. truncatula. Experimental replacement of the critical serine by an alanine in the selectivity filter of Lj-POLLUX conferred a symbiotic performance indistinguishable from DMI1. Electrophysiological characterization of DMI1 and Lj-CASTOR (wild-type and mutants) by planar lipid bilayer experiments combined with calcium imaging in Human Embryonic Kidney-293 cells expressing DMI1 (the wild type and mutants) suggest that the serine-to-alanine substitution conferred reduced conductance with a long open state to DMI1 and improved its efficiency in mediating calcium oscillations. We propose that this single amino acid replacement in the selectivity filter made DMI1 solo sufficient for symbiosis, thus explaining the selective advantage of this allele at the mechanistic level. PMID:22706284

Accuracies of breeding values for dry matter intake using nongenotyped animals and predictor traits in different lactations.

PubMed

Manzanilla-Pech, C I V; Veerkamp, R F; de Haas, Y; Calus, M P L; Ten Napel, J

2017-11-01

Given the interest of including dry matter intake (DMI) in the breeding goal, accurate estimated breeding values (EBV) for DMI are needed, preferably for separate lactations. Due to the limited amount of records available on DMI, 2 main approaches have been suggested to compute those EBV: (1) the inclusion of predictor traits, such as fat- and protein-corrected milk (FPCM) and live weight (LW), and (2) the addition of genomic information of animals using what is called genomic prediction. Recently, several methodologies to estimate EBV utilizing genomic information (EBV) have become available. In this study, a new method known as single-step ridge-regression BLUP (SSRR-BLUP) is suggested. The SSRR-BLUP method does not have an imposed limit on the number of genotyped animals, as the commonly used methods do. The objective of this study was to estimate genetic parameters using a relatively large data set with DMI records, as well as compare the accuracies of the EBV for DMI. These accuracies were obtained using 4 different methods: BLUP (using pedigree for all animals with phenotypes), genomic BLUP (GBLUP; only for genotyped animals), single-step GBLUP (SS-GBLUP), and SSRR-BLUP (for genotyped and nongenotyped animals). Records from different lactations, with or without predictor traits (FPCM and LW), were used in the model. Accuracies of EBV for DMI (defined as the correlation between the EBV and pre-adjusted DMI phenotypes divided by the average accuracy of those phenotypes) ranged between 0.21 and 0.38 across methods and scenarios. Accuracies of EBV for DMI using BLUP were the lowest accuracies obtained across methods. Meanwhile, accuracies of EBV for DMI were similar in SS-GBLUP and SSRR-BLUP, and lower for the GBLUP method. Hence, SSRR-BLUP could be used when the number of genotyped animals is large, avoiding the construction of the inverse genomic relationship matrix. Adding information on DMI from different lactations in the reference population gave higher accuracies in comparison when only lactation 1 was included. Finally, no benefit was obtained by adding information on predictor traits to the reference population when DMI was already included. However, in the absence of DMI records, having records on FPCM and LW from different lactations is a good way to obtain EBV with a relatively good accuracy. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Simultaneous control of the Dzyaloshinskii-Moriya interaction and magnetic anisotropy in nanomagnetic trilayers

DOE PAGES

Balk, Andrew; Kim, Kyoung-Whan; Pierce, Daniel T.; ...

2017-08-17

Magneto-optical Kerr effect (MOKE) microscopy measurements of magnetic bubble domains demonstrate that Ar + irradiation around 100 eV can tune the Dzyaloshinskii-Moriya interaction (DMI) in Pt/Co/Pt trilayers. Varying the irradiation energy and dose changes the DMI sign and magnitude separately from the magnetic anisotropy, allowing tuning of the DMI while holding the coercive field constant. This simultaneous control emphasizes the different physical origins of these effects. To accurately measure the DMI, we propose and apply a physical model for a poorly understood peak in domain wall velocity at zero in-plane field. Finally, the ability to tune the DMI with themore » spatial resolution of the Ar + irradiation enables new fundamental investigations and technological applications of chiral nanomagnetics.« less

A role for the mevalonate pathway in early plant symbiotic signaling

PubMed Central

Venkateshwaran, Muthusubramanian; Jayaraman, Dhileepkumar; Chabaud, Mireille; Genre, Andrea; Balloon, Allison J.; Maeda, Junko; Forshey, Kari; den Os, Désirée; Kwiecien, Nicholas W.; Coon, Joshua J.; Barker, David G.; Ané, Jean-Michel

2015-01-01

Rhizobia and arbuscular mycorrhizal fungi produce signals that are perceived by host legume receptors at the plasma membrane and trigger sustained oscillations of the nuclear and perinuclear Ca2+ concentration (Ca2+ spiking), which in turn leads to gene expression and downstream symbiotic responses. The activation of Ca2+ spiking requires the plasma membrane-localized receptor-like kinase Does not Make Infections 2 (DMI2) as well as the nuclear cation channel DMI1. A key enzyme regulating the mevalonate (MVA) pathway, 3-Hydroxy-3-Methylglutaryl CoA Reductase 1 (HMGR1), interacts with DMI2 and is required for the legume–rhizobium symbiosis. Here, we show that HMGR1 is required to initiate Ca2+ spiking and symbiotic gene expression in Medicago truncatula roots in response to rhizobial and arbuscular mycorrhizal fungal signals. Furthermore, MVA, the direct product of HMGR1 activity, is sufficient to induce nuclear-associated Ca2+ spiking and symbiotic gene expression in both wild-type plants and dmi2 mutants, but interestingly not in dmi1 mutants. Finally, MVA induced Ca2+ spiking in Human Embryonic Kidney 293 cells expressing DMI1. This demonstrates that the nuclear cation channel DMI1 is sufficient to support MVA-induced Ca2+ spiking in this heterologous system. PMID:26199419

A role for the mevalonate pathway in early plant symbiotic signaling.

PubMed

Venkateshwaran, Muthusubramanian; Jayaraman, Dhileepkumar; Chabaud, Mireille; Genre, Andrea; Balloon, Allison J; Maeda, Junko; Forshey, Kari; den Os, Désirée; Kwiecien, Nicholas W; Coon, Joshua J; Barker, David G; Ané, Jean-Michel

2015-08-04

Rhizobia and arbuscular mycorrhizal fungi produce signals that are perceived by host legume receptors at the plasma membrane and trigger sustained oscillations of the nuclear and perinuclear Ca(2+) concentration (Ca(2+) spiking), which in turn leads to gene expression and downstream symbiotic responses. The activation of Ca(2+) spiking requires the plasma membrane-localized receptor-like kinase Does not Make Infections 2 (DMI2) as well as the nuclear cation channel DMI1. A key enzyme regulating the mevalonate (MVA) pathway, 3-Hydroxy-3-Methylglutaryl CoA Reductase 1 (HMGR1), interacts with DMI2 and is required for the legume-rhizobium symbiosis. Here, we show that HMGR1 is required to initiate Ca(2+) spiking and symbiotic gene expression in Medicago truncatula roots in response to rhizobial and arbuscular mycorrhizal fungal signals. Furthermore, MVA, the direct product of HMGR1 activity, is sufficient to induce nuclear-associated Ca(2+) spiking and symbiotic gene expression in both wild-type plants and dmi2 mutants, but interestingly not in dmi1 mutants. Finally, MVA induced Ca(2+) spiking in Human Embryonic Kidney 293 cells expressing DMI1. This demonstrates that the nuclear cation channel DMI1 is sufficient to support MVA-induced Ca(2+) spiking in this heterologous system.

Prediction and validation of residual feed intake and dry matter intake in Danish lactating dairy cows using mid-infrared spectroscopy of milk.

PubMed

Shetty, N; Løvendahl, P; Lund, M S; Buitenhuis, A J

2017-01-01

The present study explored the effectiveness of Fourier transform mid-infrared (FT-IR) spectral profiles as a predictor for dry matter intake (DMI) and residual feed intake (RFI). The partial least squares regression method was used to develop the prediction models. The models were validated using different external test sets, one randomly leaving out 20% of the records (validation A), the second randomly leaving out 20% of cows (validation B), and a third (for DMI prediction models) randomly leaving out one cow (validation C). The data included 1,044 records from 140 cows; 97 were Danish Holstein and 43 Danish Jersey. Results showed better accuracies for validation A compared with other validation methods. Milk yield (MY) contributed largely to DMI prediction; MY explained 59% of the variation and the validated model error root mean square error of prediction (RMSEP) was 2.24kg. The model was improved by adding live weight (LW) as an additional predictor trait, where the accuracy R 2 increased from 0.59 to 0.72 and error RMSEP decreased from 2.24 to 1.83kg. When only the milk FT-IR spectral profile was used in DMI prediction, a lower prediction ability was obtained, with R 2 =0.30 and RMSEP=2.91kg. However, once the spectral information was added, along with MY and LW as predictors, model accuracy improved and R 2 increased to 0.81 and RMSEP decreased to 1.49kg. Prediction accuracies of RFI changed throughout lactation. The RFI prediction model for the early-lactation stage was better compared with across lactation or mid- and late-lactation stages, with R 2 =0.46 and RMSEP=1.70. The most important spectral wavenumbers that contributed to DMI and RFI prediction models included fat, protein, and lactose peaks. Comparable prediction results were obtained when using infrared-predicted fat, protein, and lactose instead of full spectra, indicating that FT-IR spectral data do not add significant new information to improve DMI and RFI prediction models. Therefore, in practice, if full FT-IR spectral data are not stored, it is possible to achieve similar DMI or RFI prediction results based on standard milk control data. For DMI, the milk fat region was responsible for the major variation in milk spectra; for RFI, the major variation in milk spectra was within the milk protein region. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Deep mural injury and perforation after colonic endoscopic mucosal resection: a new classification and analysis of risk factors.

PubMed

Burgess, Nicholas G; Bassan, Milan S; McLeod, Duncan; Williams, Stephen J; Byth, Karen; Bourke, Michael J

2017-10-01

Perforation is the most serious complication associated with endoscopic mucosal resection (EMR). We propose a new classification for the appearance and integrity of the muscularis propria (MP) after EMR including various extents of deep mural injury (DMI). Risk factors for these injuries were analysed. Endoscopic images and histological specimens of consecutive patients undergoing EMR of colonic laterally spreading lesions ≥20 mm at a large Australian tertiary referral endoscopy unit were retrospectively analysed using our new DMI classification system. DMI was graded according to MP injury (I/II intact MP without/with fibrosis, III target sign, IV/V obvious transmural perforation without/with contamination). Histological specimens were examined for included MP and patient outcomes were recorded. All type III-V DMI signs were clipped if possible, types I and II DMI were clipped at the endoscopists' discretion. EMR was performed in 911 lesions (mean size 37 mm) in 802 patients (male sex 51.4%, mean age 67 years). DMI signs were identified in 83 patients (10.3%). Type III-V DMI was identified in 24 patients (3.0%); clipping was successfully performed in all patients. A clinically significant perforation occurred in two patients (0.2%). Only one of the 59 type I/II cases experienced a delayed perforation. 85.5% of patients with DMI were discharged on the same day, all without sequelae. On multivariable analysis, type III-V DMI was associated with transverse colon location (OR 3.55, p=0.028), en bloc resection (OR 3.84, p=0.005) and high-grade dysplasia or submucosal invasive cancer (OR 2.97, p 0.014). In this retrospective analysis, use of the new classification and management with clips appeared to be a safe approach. Advanced DMI types (III-V) occurred in 3.0% of patients and were associated with identifiable risk factors. Further prospective clinical studies should use this new classification. NCT01368289; results. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Environmental factors affecting feed intake of steers in different housing systems in the summer

NASA Astrophysics Data System (ADS)

Koknaroglu, H.; Otles, Z.; Mader, T.; Hoffman, M. P.

2008-07-01

A total of 188 yearling steers of predominantly Angus and Hereford breeds, with mean body weight of 299 kg, were used in this study, which started on 8 April and finished on 3 October, to assess the effects of environmental factors on feed intake of steers in various housing systems. Housing consisted of outside lots with access to overhead shelter, outside lots with no overhead shelter and a cold confinement building. Ad libitum corn, 2.27 kg of 35% dry matter whole plant sorghum silage and 0.68 kg of a 61% protein-vitamin-mineral supplement was offered. Feed that was not consumed was measured to determine feed intake. The temperature data were recorded by hygro-thermographs. Hourly temperatures and humidity were used to develop weather variables. Regression analysis was used and weather variables were regressed on dry matter intake (DMI). When addition of a new variable did not improve R 2 more than one unit, then the number of variables in the model was truncated. Cattle in confinement had lower DMI than those in open lots and those in open lots with access to an overhead shelter ( P < 0.05). Cattle in outside lots with access to overhead shelter had similar DMI compared to those in open lots ( P = 0.065). Effect of heat was predominantly displayed in August in the three housing systems. In terms of explaining variation in DMI, in outside lots with access to overhead shelter, average and daytime temperatures were important factors, whereas in open lots, nocturnal, peak and average temperatures were important factors. In confinement buildings, the previous day’s temperature and humidity index were the most important factors explaining variation in DMI. Results show the effect of housing and weather variables on DMI in summer and when considering these results, cattle producers wishing to improve cattle feedlot performance should consider housing conditions providing less stress or more comfort.

Highly Conductive PEDOT:PSS Films with 1,3-Dimethyl-2-Imidazolidinone as Transparent Electrodes for Organic Light-Emitting Diodes.

PubMed

Kim, Jin Hee; Joo, Chul Woong; Lee, Jonghee; Seo, Yoon Kyung; Han, Joo Won; Oh, Ji Yoon; Kim, Jong Su; Yu, Seunggun; Lee, Jae Hyun; Lee, Jeong-Ik; Yun, Changhun; Choi, Bum Ho; Kim, Yong Hyun

2016-09-01

Highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) ( PSS) films as transparent electrodes for organic light-emitting diodes (OLEDs) are doped with a new solvent 1,3-dimethyl-2-imidazolidinone (DMI) and are optimized using solvent post-treatment. The DMI doped PSS films show significantly enhanced conductivities up to 812.1 S cm(-1) . The sheet resistance of the PSS films doped with DMI is further reduced by various solvent post-treatment. The effect of solvent post-treatment on DMI doped PSS films is investigated and is shown to reduce insulating PSS in the conductive films. The solvent posttreated PSS films are successfully employed as transparent electrodes in white OLEDs. It is shown that the efficiency of OLEDs with the optimized DMI doped PSS films is higher than that of reference OLEDs doped with a conventional solvent (ethylene glycol). The results present that the optimized PSS films with the new solvent of DMI can be a promising transparent electrode for low-cost, efficient ITO-free white OLEDs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Four Genes of Medicago truncatula Controlling Components of a Nod Factor Transduction Pathway

PubMed Central

Catoira, Romy; Galera, Christine; de Billy, Francoise; Penmetsa, R. Varma; Journet, Etienne-Pascal; Maillet, Fabienne; Rosenberg, Charles; Cook, Douglas; Gough, Clare; Dénarié, Jean

2000-01-01

Rhizobium nodulation (Nod) factors are lipo-chitooligosaccharides that act as symbiotic signals, eliciting several key developmental responses in the roots of legume hosts. Using nodulation-defective mutants of Medicago truncatula, we have started to dissect the genetic control of Nod factor transduction. Mutants in four genes (DMI1, DMI2, DMI3, and NSP) were pleiotropically affected in Nod factor responses, indicating that these genes are required for a Nod factor–activated signal transduction pathway that leads to symbiotic responses such as root hair deformations, expressions of nodulin genes, and cortical cell divisions. Mutant analysis also provides evidence that Nod factors have a dual effect on the growth of root hair: inhibition of endogenous (plant) tip growth, and elicitation of a novel tip growth dependent on (bacterial) Nod factors. dmi1, dmi2, and dmi3 mutants are also unable to establish a symbiotic association with endomycorrhizal fungi, indicating that there are at least three common steps to nodulation and endomycorrhization in M. truncatula and providing further evidence for a common signaling pathway between nodulation and mycorrhization. PMID:11006338

Dynamics of chiral domain wall under the spin-orbit torques in heavy metal/ferromagnet bilayers with in-plane anisotropy

NASA Astrophysics Data System (ADS)

Yan, Han; He, Peng-Bin; Cai, Meng-Qiu; Li, Zai-Dong

2017-11-01

The dynamics of domain wall driven by the spin-orbit torques is theoretically studied in the heavy metal/ferromagnet bilayer with Dzyaloshinskii-Moriya interaction (DMI) and in-plane magnetic anisotropy. Based on the Walker profile, we infer that DMI has a selectivity for the chirality of head-to-head (tail-to-tail) static wall. By analyzing the dynamic equations obtained from the collective coordinates methods, we find that there exists a switching or a hysteresis of the polarity of wall in the low-current regime. In the presence of DMI, the wall can keep sustained propagation which velocity saturates for high current and is proportional to the strength of DMI. Furthermore, the DMI makes the adjacent walls possess the same chirality and move in the same direction.

Precision diet formulation to improve performance and profitability across various climates: Modeling the implications of increasing the formulation frequency of dairy cattle diets.

PubMed

White, Robin R; Capper, Judith L

2014-03-01

The objective of this study was to use a precision nutrition model to simulate the relationship between diet formulation frequency and dairy cattle performance across various climates. Agricultural Modeling and Training Systems (AMTS) CattlePro diet-balancing software (Cornell Research Foundation, Ithaca, NY) was used to compare 3 diet formulation frequencies (weekly, monthly, or seasonal) and 3 levels of climate variability (hot, cold, or variable). Predicted daily milk yield (MY), metabolizable energy (ME) balance, and dry matter intake (DMI) were recorded for each frequency-variability combination. Economic analysis was conducted to calculate the predicted revenue over feed and labor costs. Diet formulation frequency affected ME balance and MY but did not affect DMI. Climate variability affected ME balance and DMI but not MY. The interaction between climate variability and formulation frequency did not affect ME balance, MY, or DMI. Formulating diets more frequently increased MY, DMI, and ME balance. Economic analysis showed that formulating diets weekly rather than seasonally could improve returns over variable costs by $25,000 per year for a moderate-sized (300-cow) operation. To achieve this increase in returns, an entire feeding system margin of error of <1% was required. Formulating monthly, rather than seasonally, may be a more feasible alternative as this requires a margin of error of only 2.5% for the entire feeding system. Feeding systems with a low margin of error must be developed to better take advantage of the benefits of precision nutrition. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Disease management index of potential years of life lost as a tool for setting priorities in national disease control using OECD health data.

PubMed

Jang, Sung-In; Nam, Jung-Mo; Choi, Jongwon; Park, Eun-Cheol

2014-03-01

Limited healthcare resources make it necessary to maximize efficiency in disease management at the country level by priority-setting according to disease burden. To make the best priority settings, it is necessary to measure health status and have standards for its judgment, as well as consider disease management trends among nations. We used 17 International Classification of Diseases (ICD) categories of potential years of life lost (YPLL) from Organization for Economic Co-operation and Development (OECD) health data for 2012, 37 disease diagnoses YPLL from OECD health data for 2009 across 22 countries and disability-adjusted life years (DALY) from the World Health Organization (WHO). We set a range of 1-1 for each YPLL per disease in a nation (position value for relative comparison, PARC). Changes over 5 years were also accounted for in this disease management index (disease management index, DMI). In terms of ICD categories, the DMI indicated specific areas for priority setting for different countries with regard to managing disease treatment and diagnosis. Our study suggests that DMI is a realistic index that reflects trend changes over the past 5 years to the present state, and PARC is an easy index for identifying relative status. Moreover, unlike existing indices, DMI and PARC make it easy to conduct multiple comparisons among countries and diseases. DMI and PARC are therefore useful tools for policy implications and for future studies incorporating them and other existing indexes. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

The MtDMI2-MtPUB2 Negative Feedback Loop Plays a Role in Nodulation Homeostasis1[OPEN

PubMed Central

Deng, Jie; Zhu, Fugui; Lu, Zheng

2018-01-01

DOES NOT MAKE INFECTION 2 (MtDMI2) is a Leu rich repeat-type receptor kinase required for signal transduction in the Medicago truncatula/Sinorhizobium meliloti symbiosis pathway. However, the mechanisms through which MtDMI2 participates in nodulation homeostasis are poorly understood. In this study, we identified MtPUB2—a novel plant U-box (PUB)–type E3 ligase—and showed that it interacts with MtDMI2. MtDMI2 and MtPUB2 accumulation were shown to be similar in various tissues. Roots of plants in which MtPUB2 was silenced by RNAi (MtPUB2-RNAi plants) exhibited impaired infection threads, fewer nodules, and shorter primary root lengths compared to those of control plants transformed with empty vector. Using liquid chromatography-tandem mass spectrometry, we showed that MtDMI2 phosphorylates MtPUB2 at Ser-316, Ser-421, and Thr-488 residues. When MtPUB2-RNAi plants were transformed with MtPUB2S421D, which mimics the phosphorylated state, MtDMI2 was persistently ubiquitinated and degraded by MtPUB2S421D, resulting in fewer nodules than observed in MtPUB2/MtPUB2-RNAi-complemented plants. However, MtPUB2S421A/MtPUB2-RNAi-complemented plants showed no MtPUB2 ubiquitination activity, and their nodulation phenotype was similar to that of MtPUB2-RNAi plants transformed with empty vector. Further studies demonstrated that these proteins form a negative feedback loop of the prey (MtDMI2)-predator (MtPUB2) type. Our results suggest that the MtDMI2-MtPUB2 negative feedback loop, which displays crosstalk with the long-distance autoregulation of nodulation via MtNIN, plays an important role in nodulation homeostasis. PMID:29440269

RELATIONSHIP OF ADIPOKINES AND PROINFLAMMATORY CYTOKINES AMONG ASIAN INDIANS WITH OBESITY AND YOUTH ONSET TYPE 2 DIABETES.

PubMed

Gokulakrishnan, Kuppan; Amutha, Anandakumar; Ranjani, Harish; Bibin, Subramanian Y; Balakumar, Mahalingam; Pandey, Gautam Kumar; Anjana, Ranjit Mohan; Ali, Mohammed K; Narayan, K M Venkat; Mohan, Viswanathan

2015-10-01

It is well known that inflammation is associated with diabetes, but it is unclear whether obesity mediates this association in individuals with youth-onset type 2 diabetes mellitus (T2DM-Y). We recruited individuals with T2DM-Y (age at onset <25 years) and age-matched normal glucose tolerance (NGT) subjects. Participants were further classified using Asia-Pacific body mass index cut-points for obesity and categorized as: nonobese NGT (n = 100), Obese NGT (n = 50), nonobese T2DM-Y (n = 50), and obese T2DM-Y (n = 50). We compared adipokines (adiponectin and leptin) and proinflammatory cytokines (tumor necrosis factor alpha [TNF-α] and monocyte chemotactic protein-1 [MCP-1]) across groups. Compared to nonobese NGT, the other 3 groups (obese NGT, nonobese T2DM-Y, and obese T2DM-Y) were found to have lower adiponectin (7.7 vs. 5.7, 4.2, 3.8 μg/mL, P<.01), and higher leptin (3.6 vs. 5.4, 5.7, 7.9 μg/mL, P<.001) and MCP 1 (186 vs. 272, 340, 473 pg/mL, P<.001) respectively. However, TNF-α levels were higher only among nonobese T2DM-Y (112 pg/mL) and obese T2DM-Y (141 pg/mL, P<.01 for each). After adjusting for age, sex, waist, hypertension, homeostatic model assessment of insulin resistance (HOMA-IR), serum cholesterol, triglycerides, and family history of diabetes, adiponectin was associated with 33% and 41% lower odds of being nonobese T2DM and obese T2DM, respectively. However, adjusted for same factors, leptin, TNF-α, and MCP-1 were associated with markedly higher odds (5- to 14-fold) of nonobese and obese T2DM. In young Asian Indians, leptin and proinflammatory cytokines are positively, and adiponectin negatively, associated with both nonobese and obese T2DM-Y compared to nonobese NGT individuals.

Ultrafast spin dynamics and switching via spin transfer torque in antiferromagnets with weak ferromagnetism

PubMed Central

Kim, Tae Heon; Grünberg, Peter; Han, Song Hee; Cho, Beongki

2016-01-01

The spin-torque driven dynamics of antiferromagnets with Dzyaloshinskii-Moriya interaction (DMI) were investigated based on the Landau-Lifshitz-Gilbert-Slonczewski equation with antiferromagnetic and ferromagnetic order parameters (l and m, respectively). We demonstrate that antiferromagnets including DMI can be described by a 2-dimensional pendulum model of l. Because m is coupled with l, together with DMI and exchange energy, close examination of m provides fundamental understanding of its dynamics in linear and nonlinear regimes. Furthermore, we discuss magnetization reversal as a function of DMI and anisotropy energy induced by a spin current pulse. PMID:27713522

Phenotypic relationships among methane production traits assessed under ad libitum feeding of beef cattle.

PubMed

Bird-Gardiner, T; Arthur, P F; Barchia, I M; Donoghue, K A; Herd, R M

2017-10-01

Angus cattle from 2 beef cattle projects in which daily methane production (MPR) was measured were used in this study to examine the nature of the relationships among BW, DMI, and methane traits of beef cattle fed ad libitum on a roughage diet or a grain-based feedlot diet. In both projects methane was measured using the GreenFeed Emission Monitoring system, which provides multiple short-term breath measures of methane production. The data used for this study were from 119 Angus heifers over 15 d on a roughage diet and 326 Angus steers over 70 d on a feedlot diet. Mean (±SD) age, BW, and DMI were 372 ± 28 d, 355 ± 37 kg, and 8.1 ± 1.3 kg/d for the heifers and 554 ± 86 d, 577 ± 69 kg, and 13.3 ± 2.0 kg/d for the steers, respectively. The corresponding mean MPR was 212 g/d for heifers and 203 g/d for steers. Additional traits studied included methane yield (MY; MPR/DMI), methane intensity (MPR/BW), and 3 forms of residual methane production (RMP), which is a measure of actual minus predicted MPR. For RMP, RMP, and RMP predicted MPR were obtained by regression of MPR on BW, on DMI, and on both DMI and BW, respectively. The 2 data sets were analyzed separately using the same statistical procedures. For both feed types the relationships between MPR and DMI and between MPR and BW were both positive and linear. The correlation between MPR and DMI was similar to that between MPR and BW, although the correlations were stronger for the roughage diet ( = 0.75 for MPR vs. DMI; = 0.74 for MPR vs. BW) than the grain-based diet ( = 0.62 for MPR vs. DMI; = 0.66 for MPR vs. BW). The correlation between MY and DMI was negative and moderate for the roughage ( = -0.68) and grain-based ( = -0.59) diets, a finding that is different from the nonsignificant correlations reported in studies of cattle on a restricted roughage diet. The 3 RMP traits were strongly correlated ( values from 0.76 to 0.99) with each other for both the roughage and the grain-based diets, which indicates that using RMP to lower MPR could provide a result similar to using RMP in cattle. As feed intake (DMI) is more difficult to measure than BW, this result implies that under ad libitum feeding situations in which DMI cannot be measured, RMP can be used to identify higher- or lower-RMP animals with similar levels of effectiveness as RMP.

High Temperature Transparent Furnace Development

NASA Technical Reports Server (NTRS)

Bates, Stephen C.

1997-01-01

This report describes the use of novel techniques for heat containment that could be used to build a high temperature transparent furnace. The primary objective of the work was to experimentally demonstrate transparent furnace operation at 1200 C. Secondary objectives were to understand furnace operation and furnace component specification to enable the design and construction of a low power prototype furnace for delivery to NASA in a follow-up project. The basic approach of the research was to couple high temperature component design with simple concept demonstration experiments that modify a commercially available transparent furnace rated at lower temperature. A detailed energy balance of the operating transparent furnace was performed, calculating heat losses through the furnace components as a result of conduction, radiation, and convection. The transparent furnace shells and furnace components were redesigned to permit furnace operation at at least 1200 C. Techniques were developed that are expected to lead to significantly improved heat containment compared with current transparent furnaces. The design of a thermal profile in a multizone high temperature transparent furnace design was also addressed. Experiments were performed to verify the energy balance analysis, to demonstrate some of the major furnace improvement techniques developed, and to demonstrate the overall feasibility of a high temperature transparent furnace. The important objective of the research was achieved: to demonstrate the feasibility of operating a transparent furnace at 1200 C.

Relationship between feed intake, feeding behaviors, performance, and ultrasound carcass measurements in growing purebred Angus and Hereford bulls.

PubMed

Kayser, W; Hill, R A

2013-11-01

The objectives of this study were to examine the growth, DMI, and feeding behaviors of Angus and Hereford bulls; identify the relationships between feeding behaviors and variation in DMI and residual feed intake (RFI); and determine the value of feeding behaviors in predicting DMI. Individual DMI was measured in Angus bulls (n=189; initial BW=427±3.4 kg) and Hereford bulls (n=146; initial BW=411±4.1 kg) fed a grower ration for 71 d in 2009, 78 d in 2010, and 74 d in 2011 using a GrowSafe intake monitoring system. Feeding frequency (FF, meals/d), head down duration (HDD, s/d), head down duration per meal (HDDM, HDD/FF, s/meal), average meal size [AMS, kg/(meal·d)], and feeding rate (FR, g/s) were also measured or calculated using behavior data collected by the GrowSafe system. Ultrasound measures of 12th-rib fat thickness (UFT), longissimus muscle area (ULMA), and intramuscular fat (IMF) were determined during the midtest-weight event of every trial. The data from 3 yr were pooled to generate mean differences between the breeds. Residual feed intake was calculated using a linear regression of DMI on ADG and midtest BW0.75 (MMWT). Animals were classified into 3 RFI groups based on their RFI score as Low (>0.5 SD below the mean), Average (±0.5 SD from the mean), or High RFI (>0.5 SD above the mean). Angus bulls in the Low RFI group consumed 17% (P<0.0001) less DM than the bulls in the High RFI group, while in the Hereford bulls there was a 14% (P<0.0001) difference in DMI between Low and High RFI groups. Significant phenotypic correlations were observed between RFI and DMI (0.83, 0.77), G:F (-0.65, -0.51), HDD (0.41, 0.59), HDDM (0.40, 0.53), AMS (0.52, 0.36), and FR (-0.31, -0.51) in Angus and Hereford bulls, respectively. The HDD, HDDM, and FR were significantly correlated with DMI. The feeding behavior traits, HDD, HDDM, and FR when added to the RFI base model, explained 18, 17, and 13%, respectively, of the variation in DMI not explained by ADG and MMWT in Angus bulls. Similarly, in Hereford bulls, HDD, HDDM, and FR explained 35, 26, and 24%, respectively, of the variation in DMI not explained by ADG and MMWT. These data suggest that feeding behaviors are related to DMI of growing Angus and Hereford bulls.

Genetic strain and diet effects on grazing behavior, pasture intake, and milk production.

PubMed

Sheahan, A J; Kolver, E S; Roche, J R

2011-07-01

Understanding how dairy cows adjust their grazing behavior in response to feed supplements is important for the development of management strategies that optimize profit from supplementation. New Zealand Holstein-Friesian (HF) cows have been selected for milk production on a predominantly pasture-based diet; in comparison, HF cows of North American (NA) ancestry have been selected almost exclusively for milk yield and fed diets high in nonfiber carbohydrates (NFC). We hypothesized, therefore, that supplementation would have differing effects on grazing behavior, pasture dry matter intake (DMI), and milk production in these genetic strains at peak, mid, and late lactation. A study was conducted over 2 consecutive lactations, with NA and NZ cows randomly allocated at calving to 0, 3, or 6 kg of dry matter/day concentrate plus unrestricted access to pasture. Pasture DMI, milk production, and grazing behavior were recorded at peak, mid, and late lactation. Concentrates were fed in equal amounts at morning and afternoon milking. The NA cows produced more milk and milk components, and had a greater pasture DMI, despite spending less time grazing. Declines in time spent grazing and pasture DMI were associated with increasing concentrate DMI. Grazing behavior following morning supplementation was different from that recorded following afternoon supplementation. Grazing ceased following morning supplementation before rumen fill could be a limiting factor, and the length of the grazing interval was inversely proportional to the amount of concentrate offered; these results suggest that physiological rather than physical stimuli were responsible for grazing cessation. The decrease in time spent grazing with increasing concentrate DMI is consistent with changes in neuroendocrine factors secreted in response to the presence of food in the digestive tract or with circulating products of digestion. After afternoon supplementation, sunset signaled the end of grazing irrespective of stage of lactation, timing of sunset, or supplementation status, suggesting that photoperiod influenced grazing behavior. Results confirmed changes in grazing behavior, an associated reduction in pasture DMI, and an increase in milk production when cows consume increasing amounts of concentrates. However, as the effect of supplement on grazing behavior differed between morning and afternoon supplementation, further research is required to better understand the factors controlling grazing behavior, to allow improved milk production responses to supplementary feeding. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Synthesis, characterization, AIM and NBO analysis of HMX/DMI cocrystal explosive

NASA Astrophysics Data System (ADS)

Lin, He; Zhu, Shun-Guan; Li, Hong-Zhen; Peng, Xin-Hua

2013-09-01

1,3,5,7-Tetranitro-1,3,5,7-tetrazacyclooctane (HMX)/1,3-dimethyl-2-imidazolidinone (DMI) cocrystal explosive was synthesized and characterized by using X-ray single crystal diffraction. HMX/DMI cocrystal crystallizes in the monoclinic system (space group Cm), with cell parameters a = 7.231(2)Å, b = 14.739(2)Å, c = 7.552(1)Å, β = 96.66°. In addition, density functional theory, involving binding energy, natural bond orbital (NBO) analysis, atoms in molecule (AIM) analysis, band structure, and density of states, was adopted to investigate intermolecular interactions for the formation of HMX/DMI cocrystal. The results show that hydrogen bondings between methylene groups of HMX molecules and O atoms of DMI molecules are the main intermolecular interactions. This research provides the basis for further design of cocrystal explosives, which are composed of HMX and energetic materials.

Brillouin light scattering investigation of interfacial Dzyaloshinskii–Moriya interaction in ultrathin Co/Pt nanostripe arrays

NASA Astrophysics Data System (ADS)

Bouloussa, H.; Yu, J.; Roussigné, Y.; Belmeguenai, M.; Stashkevitch, A.; Yang, H.; Chérif, S. M.

2018-06-01

Interface Dzyaloshinskii–Moriya interaction (iDMI) is known to induce spinwaves non-reciprocity in ultrathin films. Indeed, Brillouin light scattering has been used to investigate how the lateral size reduction can affect the iDMI constant in Pt (6 nm)/Co (3 nm) based-nanostripe arrays. For this, 100 and 300 nm-width nanostripes have been fabricated using e-beam lithography and ion etching, and their behaviour has then been compared to the reference continuous film. The experimental data showed that the measured iDMI induced non-reciprocity is slightly different for the 100 nm-width nanostripes with respect to the other samples. This suggests that the width of the nanostripes can influence the strength of the apparent iDMI if this dimension is comparable to the spin waves attenuation length propagating within the nanostripes. Indeed, in contrast to the other samples, the linear frequency difference (non-reciprocity) behaviour versus wavenumber for the 100 nm-width nanostripes has been analysed and discussed through two approaches: either a different iDMI constant or an iDMI constant similar to one of the continuous films with a non-zero intercept for a zero wavenumber.

Response profiles of enteric methane emissions and lactational performance during habituation to dietary coconut oil in dairy cows.

PubMed

Hollmann, M; Powers, W J; Fogiel, A C; Liesman, J S; Beede, D K

2013-03-01

Dietary coconut oil (CNO) can reduce dry matter intake (DMI), enteric methane (eCH(4)) emissions, and milk fat yield of lactating cows. The goals of this research were to examine responses to different CNO concentrations during the habituation period (34-d) and to evaluate temporal patterns of DMI, eCH(4), and milk fat yield. Treatment diets contained (dry basis): 0.0% (CNO0), 1.3% (CNO1.3), 2.7% (CNO2.7), 3.3% (CNO3.3), or 4.0% CNO (CNO4). In experiment 1, 12 primi- or small secundiparous cows were housed in individual, environmentally controlled rooms and fed CNO0, CNO1.3, CNO2.7, or CNO4. Measurements included DMI, eCH(4), and milk yield and composition. Due to a precipitous drop in DMI (26%), cows fed CNO4 were replaced with cows fed CNO3.3 following d 10. Dietary CNO of 2.7% or more reduced eCH(4) emissions. Reduction was greater with increased CNO and during the first than the second half of the day. Simultaneously, decline in DMI of cows fed CNO2.7, CNO3.3, or CNO4 was increasingly precipitous with increased CNO concentration. Total-tract neutral detergent fiber (NDF) digestibility during wk 5 was reduced in cows fed CNO2.7 or CNO3.3, which in part explained concomitantly reduced eCH(4)/DMI. In addition, milk fat yield was depressed at an increasing rate in cows fed CNO2.7, CNO3.3, and CNO4. In experiment 2, DMI was measured individually in 12 multiparous cows during habituation to CNO0, CNO1.3, CNO2.7, or CNO3.3 for 21 d before relocation to individual, environmentally controlled rooms. Dietary CNO2.7 or CNO3.3 reduced DMI by d 4 and total-tract NDF digestibility during wk 5. Relocation to individual rooms was associated with a 15% reduction in DMI, which was not affected by treatment. Results showed that 2.7% or more dietary CNO reduced eCH(4) and DMI, caused milk fat depression, and decreased NDF digestibility. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Integrating spot short-term measurements of carbon emissions and backward dietary energy partition calculations to estimate intake in lactating dairy cows fed ad libitum or restricted.

PubMed

Pereira, A B D; Utsumi, S A; Dorich, C D; Brito, A F

2015-12-01

The objective of this study was to use spot short-term measurements of CH4 (QCH4) and CO2 (QCO2) integrated with backward dietary energy partition calculations to estimate dry matter intake (DMI) in lactating dairy cows. Twelve multiparous cows averaging 173±37d in milk and 4 primiparous cows averaging 179±27d in milk were blocked by days in milk, parity, and DMI (as a percentage of body weight) and, within each block, randomly assigned to 1 of 2 treatments: ad libitum intake (AL) or restricted intake (RI=90% DMI) according to a crossover design. Each experimental period lasted 22d with 14d for treatments adaptation and 8d for data and sample collection. Diets contained (dry matter basis): 40% corn silage, 12% grass-legume haylage, and 48% concentrate. Spot short-term gas measurements were taken in 5-min sampling periods from 15 cows (1 cow refused sampling) using a portable, automated, open-circuit gas quantification system (GreenFeed, C-Lock Inc., Rapid City, SD) with intervals of 12h between the 2daily samples. Sampling points were advanced 2h from a day to the next to yield 16 gas samples per cow over 8d to account for diurnal variation in QCH4 and QCO2. The following equations were used sequentially to estimate DMI: (1) heat production (MJ/d)=(4.96 + 16.07 ÷ respiratory quotient) × QCO2; respiratory quotient=0.95; (2) metabolizable energy intake (MJ/d)=(heat production + milk energy) ± tissue energy balance; (3) digestible energy (DE) intake (MJ/d)=metabolizable energy + CH4 energy + urinary energy; (4) gross energy (GE) intake (MJ/d)=DE + [(DE ÷ in vitro true dry matter digestibility) - DE]; and (5) DMI (kg/d)=GE intake estimated ÷ diet GE concentration. Data were analyzed using the MIXED procedure of SAS (SAS Institute Inc., Cary, NC) and Fit Model procedure in JMP (α=0.05; SAS Institute Inc.). Cows significantly differed in DMI measured (23.8 vs. 22.4kg/d for AL and RI, respectively). Dry matter intake estimated using QCH4 and QCO2 coupled with dietary backward energy partition calculations (Equations 1 to 5 above) was highest in cows fed for AL (22.5 vs. 20.2kg/d). The resulting R(2) were 0.28 between DMI measured and DMI estimated by gaseous measurements, and 0.36 between DMI measured and DMI predicted by the National Research Council model (2001). Results showed that spot short-term measurements of QCH4 and QCO2 coupled with dietary backward estimations of energy partition underestimated DMI by 7.8%. However, the approach proposed herein was able to significantly discriminate differences in DMI between cows fed for AL or RI. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Comprehensive Numerical Modeling of the Blast Furnace Ironmaking Process

NASA Astrophysics Data System (ADS)

Zhou, Chenn; Tang, Guangwu; Wang, Jichao; Fu, Dong; Okosun, Tyamo; Silaen, Armin; Wu, Bin

2016-05-01

Blast furnaces are counter-current chemical reactors, widely utilized in the ironmaking industry. Hot reduction gases injected from lower regions of the furnace ascend, reacting with the descending burden. Through this reaction process, iron ore is reduced into liquid iron that is tapped from the furnace hearth. Due to the extremely harsh environment inside the blast furnace, it is difficult to measure or observe internal phenomena during operation. Through the collaboration between steel companies and the Center for Innovation through Visualization and Simulation, multiple computational fluid dynamics (CFD) models have been developed to simulate the complex multiphase reacting flow in the three regions of the furnace, the shaft, the raceway, and the hearth. The models have been used effectively to troubleshoot and optimize blast furnace operations. In addition, the CFD models have been integrated with virtual reality. An interactive virtual blast furnace has been developed for training purpose. This paper summarizes the developments and applications of blast furnace CFD models and the virtual blast furnace.

Fostering Social Cognition through an Imitation- and Synchronization-Based Dance/Movement Intervention in Adults with Autism Spectrum Disorder: A Controlled Proof-of-Concept Study.

PubMed

Koehne, Svenja; Behrends, Andrea; Fairhurst, Merle T; Dziobek, Isabel

2016-01-01

Since social cognition is impaired in individuals with autism spectrum disorder (ASD), this study aimed at establishing the efficacy of a newly developed imitation- and synchronization-based dance/movement intervention (SI-DMI) in fostering emotion inference and empathic feelings (emotional reaction to feelings of others) in adults with high-functioning ASD. Fifty-five adults with ASD (IQ ≥85) who were blinded to the aim of the study were assigned to receive either 10 weeks of a dance/movement intervention focusing on interpersonal movement imitation and synchronization (SI-DMI, n = 27) or a control movement intervention (CMI, n = 24) focusing on individual motor coordination (2 participants from each group declined before baseline testing). The primary outcome measure was the objective Multifaceted Empathy Test targeting emotion inference and empathic feelings. Secondary outcomes were scores on the self-rated Interpersonal Reactivity Index. The well-established automatic imitation task and synchronization finger-tapping task were used to quantify effects on imitation and synchronization functions, complemented by the more naturalistic Assessment of Spontaneous Interaction in Movement. Intention-to-treat analyses revealed that from baseline to 3 months, patients treated with SI-DMI showed a significantly larger improvement in emotion inference (d = 0.58), but not empathic feelings, than those treated with CMI (d = -0.04). On the close generalization level, SI-DMI increased synchronization skills and imitation tendencies, as well as whole-body imitation/synchronization and movement reciprocity/dialogue, compared to CMI. SI-DMI can be successful in promoting emotion inference in adults with ASD and warrants further investigation. © 2015 S. Karger AG, Basel.

The effects of prolonged administration of norepinephrine reuptake inhibitors on long-term potentiation in dentate gyrus, and on tests of spatial and object recognition memory in rats.

PubMed

Walling, Susan G; Milway, J Stephen; Ingram, Matthew; Lau, Catherine; Morrison, Gillian; Martin, Gerard M

2016-02-01

Phasic norepinephrine (NE) release events are involved in arousal, novelty detection and in plasticity processes underlying learning and memory in mammalian systems. Although the effects of phasic NE release events on plasticity and memory are prevalently documented, it is less understood what effects chronic NE reuptake inhibition and sustained increases in noradrenergic tone, might have on plasticity and cognitive processes in rodent models of learning and memory. This study investigates the effects of chronic NE reuptake inhibition on hippocampal plasticity and memory in rats. Rats were administered NE reuptake inhibitors (NRIs) desipramine (DMI; 0, 3, or 7.5mg/kg/day) or nortriptyline (NTP; 0, 10 or 20mg/kg/day) in drinking water. Long-term potentiation (LTP; 200 Hz) of the perforant path-dentate gyrus evoked potential was examined in urethane anesthetized rats after 30-32 days of DMI treatment. Short- (4-h) and long-term (24-h) spatial memory was tested in separate rats administered 0 or 7.5mg/kg/day DMI (25-30 days) using a two-trial spatial memory test. Additionally, the effects of chronically administered DMI and NTP were tested in rats using a two-trial, Object Recognition Test (ORT) at 2- and 24-h after 45 and 60 days of drug administration. Rats administered 3 or 7.5mg/kg/day DMI had attenuated LTP of the EPSP slope but not the population spike at the perforant path-dentate gyrus synapse. Short- and long-term memory for objects is differentially disrupted in rats after prolonged administration of DMI and NTP. Rats that were administered 7.5mg/kg/day DMI showed decreased memory for a two-trial spatial task when tested at 4-h. In the novel ORT, rats receiving 0 or 7.5mg/kg/day DMI showed a preference for the arm containing a Novel object when tested at both 2- and 24-h demonstrating both short- and long-term memory retention of the Familiar object. Rats that received either dose of NTP or 3mg/kg/day DMI showed impaired memory at 2-h, however this impairment was largely reversed at 24-h. Animals in the high-dose NTP (20mg/kg/day) group were impaired at both short- and long-term intervals. Activity levels, used as an index of location memory during the ORT, demonstrated that rats receiving DMI were again impaired at retaining memory for location. DMI dose-dependently disrupts LTP in the dentate gyrus of anesthetized rats and also disrupts memory for tests of spatial memory when administered for long periods. Copyright © 2016 Elsevier Inc. All rights reserved.

Ab initio studies of 1,3,5,7-tetranitro-1,3,5,7-tetrazocine/1,3-dimethyl-2-imidazolidinone cocrystal under high pressure using dispersion corrected density functional theory

NASA Astrophysics Data System (ADS)

Gu, Bang-Ming; Lin, He; Zhu, Shun-Guan

2014-04-01

A detailed study of structural, electronic, and thermodynamic properties of 1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)/1,3-dimethyl-2-imidazolidinone (DMI) cocrystal under the hydrostatic pressure of 0-100 GPa was performed by using dispersion-corrected density functional theory (DFT-D) method. The calculated crystal structure is in reasonable agreement with the experimental data at the ambient pressure. Based on the analysis of lattice constants, bond lengths, bond angles, and dihedral angles under compression, it is found that HMX molecules in HMX/DMI cocrystal are seriously distorted. In addition, as the pressure increases, the band gap decreases gradually, which suggests that HMX/DMI cocrystal is becoming more metallic. Some important intermolecular interactions between HMX and DMI are also observed in the density of states spectrum. Finally, its thermodynamic properties were characterized, and the results show that HMX/DMI cocrystal is more easily formed in the low pressure.

Augmentation of the behavioural effects of desipramine by repeated immobilization stress.

PubMed

Hadweh, Nicolás; Santibañez, Marcos; González, Marcela Paz; Forray, María Inés

2010-12-25

The present report provides evidence that repeated immobilization stress (RIS) induced a noradrenergic-dependent depressive-like behaviour and an augmented behavioural response to desipramine (DMI), a noradrenaline reuptake inhibitor (NRI), in the forced swimming test (FST). The present results show that RIS decreased the baseline of climbing behaviour in the FST. Whereas subchronic administration of DMI (10mg/kg, three times in a 24h period) induced a significantly higher increase in climbing behaviour on repeatedly stressed rats compared to controls. The results also show that the concomitant administration of the low dose of DMI (3mg/Kg) during the RIS fully prevented the decrease of climbing behaviour induced by RIS, without exerting behavioural effects in control rats, further supporting an augmented response to the DMI antidepressant effects in the repeatedly stressed rats. In conclusion, our data indicate that RIS not only changes the behavioural responses in the FST but also increases the antidepressant effects of DMI. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Models for predicting enteric methane emissions from dairy cows in North America, Europe, and Australia and New Zealand.

PubMed

Appuhamy, Jayasooriya A D R N; France, James; Kebreab, Ermias

2016-09-01

There are several models in the literature for predicting enteric methane (CH4 ) emissions. These models were often developed on region or country-specific data and may not be able to predict the emissions successfully in every region. The majority of extant models require dry matter intake (DMI) of individual animals, which is not routinely measured. The objectives of this study were to (i) evaluate performance of extant models in predicting enteric CH4 emissions from dairy cows in North America (NA), Europe (EU), and Australia and New Zealand (AUNZ) and (ii) explore the performance using estimated DMI. Forty extant models were challenged on 55, 105, and 52 enteric CH4 measurements (g per lactating cow per day) from NA, EU, and AUNZ, respectively. The models were ranked using root mean square prediction error as a percentage of the average observed value (RMSPE) and concordance correlation coefficient (CCC). A modified model of Nielsen et al. (Acta Agriculturae Scand Section A, 63, 2013 and 126) using DMI, and dietary digestible neutral detergent fiber and fatty acid contents as predictor variables, were ranked highest in NA (RMSPE = 13.1% and CCC = 0.78). The gross energy intake-based model of Yan et al. (Livestock Production Science, 64, 2000 and 253) and the updated IPCC Tier 2 model were ranked highest in EU (RMSPE = 11.0% and CCC = 0.66) and AUNZ (RMSPE = 15.6% and CCC = 0.75), respectively. DMI of cows in NA and EU was estimated satisfactorily with body weight and fat-corrected milk yield data (RMSPE < 12.0% and CCC > 0.60). Using estimated DMI, the Nielsen et al. (2013) (RMSPE = 12.7 and CCC = 0.79) and Yan et al. (2000) (RMSPE = 13.7 and CCC = 0.50) models still predicted emissions in respective regions well. Enteric CH4 emissions from dairy cows can be predicted successfully (i.e., RMSPE < 15%), if DMI can be estimated with reasonable accuracy (i.e., RMSPE < 10%). © 2016 John Wiley & Sons Ltd.

Cyanide bridged hetero-metallic polymeric complexes: Syntheses, vibrational spectra, thermal analyses and crystal structures of complexes [M(1,2-dmi)2Ni(μ-CN)4]n (M = Zn(II) and Cd(II))

NASA Astrophysics Data System (ADS)

Kürkçüoğlu, Güneş Süheyla; Sayın, Elvan; Şahin, Onur

2015-12-01

Two cyanide bridged hetero-metallic complexes of general formula, [M(1,2-dmi)2Ni(μ-CN)4]n (1,2-dmi = 1,2-dimethylimidazole and M = Zn(II) or Cd(II)) have been synthesized and characterized by vibrational (FT-IR and Raman) spectroscopy, single crystal X-ray diffraction, thermal analyses and elemental analyses. The crystallographic analyses reveal that the complexes, [Zn(1,2-dmi)2Ni(μ-CN)4] (1) and [Cd(1,2-dmi)2Ni(μ-CN)4] (2), have polymeric 2D networks. In the complexes, four cyanide groups of [Ni(CN)4]2- coordinated to the adjacent M(II) ions and distorted octahedral geometries of complexes are completed by two nitrogen atoms of trans 1,2-dmi ligands. The structures of 1 and 2 are similar and linked via intermolecular hydrogen bonding, C-H⋯Ni interactions to give rise to 3D networks. Vibration assignments are given for all the observed bands and the spectral features also supported to the crystal structures of heteronuclear complexes. The FT-IR and Raman spectra of the complexes are very much consistent with the structural data presented.

Effects of the dietary ratio of ruminal degraded to undegraded protein and feed intake on intestinal flows of endogenous nitrogen and amino acids in goats.

PubMed

Zhou, Chuanshe; Chen, Liang; Tan, Zhiliang; Tang, Shaoxun; Han, Xuefeng; Wang, Min; Kang, Jinhe; Yan, Qiongxian

2015-01-01

This study was conducted to evaluate the effects of the dietary ratio of ruminal degraded protein (RDP) to ruminal undegraded protein (RUP) and the dry matter intake (DMI) on the intestinal flows of endogenous nitrogen (N) and amino acids (AA) in goats. The experiment was designed as a 4×4 Latin square using four ruminally, duodenally and ileally cannulated goats. The treatments were arranged in a 2×2 factorial design; two ratios of RDP to RUP (65:35 and 45:55, RDP1 and RDP2, respectively) and two levels at 95% and 75% of voluntary feed intake (DMI1 and DMI2, respectively) were fed to the goats. There were no significant differences in the N intake, duodenal flow of total N, undegraded feed N, microbial N, endogenous N or ileal flow of endogenous N, but the duodenal and ileal flow of endogenous N numerically decreased by approximately 22% and 9%, respectively, when the feed intake changed from DMI1 (0.63 kg/d) to DMI2 (0.50 kg/d). The dietary ratio of RDP to RUP had significant effects (p<0.05) on the ileal flows of endogenous leucine, phenylalanine and cysteine. The present results implied that the duodenal flows of endogenous N and AA decreased when the dietary RDP to RUP ratio and DMI decreased, and the flow of endogenous AA at the ileum also decreased when the DMI decreased but increased with decreasing RDP to RUP ratios.

A dynamic model to predict fat and protein fluxes and dry matter intake associated with body reserve changes in cattle.

PubMed

Tedeschi, Luis O; Fox, Danny G; Kononoff, Paul J

2013-04-01

The objective of this paper was to develop the structure and concepts of a dynamic model to simulate dry matter intake (DMI) pattern and the fluxes of fat and protein in the body reserves of cattle associated with changes in body condition score (BCS) for application within the structure of applied nutrition models. This model was developed to add the capability of evaluating the effects of factors affecting pre- and postcalving DMI, daily energy and protein balances, and changes in BCS over a reproductive cycle. Input variables are average DMI, diet metabolizable energy, and animal information (body weight, BCS, milk production, and calf birth body weight) from each diet fed over the reproductive cycle. Because the depletion and repletion of body reserves in cattle is a complex system of coordinated metabolic processes that reflect hormonal and physiological changes caused by negative or positive energy balances, the system dynamics modeling methodology was used to develop this model. The model was used to evaluate the effect of the dynamic interactions between dietary supply and animal requirements for energy and protein on the fluxes of body fat and body protein of dairy cows over the reproductive cycle and Monte Carlo simulations were used to assess the sensitivity of the parameters. The main long-term factor affecting DMI pattern was the growth of the gravid uterus causing an increase in the volume of abdominal organs and a compression of the rumen, consequentially reducing feed intake. Changes in body reserves (fat and protein) were computed based on metabolizable energy balance, assuming different efficiency of utilization coefficients for fat and protein during repletion and mobilization. The model was evaluated with data from 37 dairy cows individually fed 3 different diets over the lactation and dry periods. The model was successful in simulating the observed pattern of DMI (mean square error was 3.59, 3.97, and 3.66 for diets A, B, and C, respectively), but it tended to underpredict DMI during late lactation [around 200 to 285 d in milk (DIM)] for all diets, suggesting changes in the model structure might be needed. The predicted BCS pattern had a trend similar to the observed values. Assuming that observed BCS represents actual body fat, the model tended to overpredict observed BCS during early lactation (0.125 BCS for 0 to 120 DIM) and underpredict it during late lactation (0.06 BCS for 180 to 270 DIM). A long-term simulation (5 lactations and 4 dry periods) with diet A indicated that the cows on this diet would have a net loss of body fat if all conditions were constant. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of forage types on digestibility, methane emissions, and nitrogen utilization efficiency in two genotypes of hill ewes.

PubMed

Zhao, Y G; Annett, R; Yan, T

2017-08-01

Thirty-six nonpregnant hill ewes (18 pure Scottish Blackface and 18 Swaledale × Scottish Blackface) aged 18 mo and weighing 48 ± 4.8 kg were allocated to 3 forage treatments balanced for genotype and BW. Each genotype was offered 3 forages (pelleted ryegrass, fresh lowland grass, and fresh hill grass) ad libitum with 6 ewes for each of the 6 genotype × diet combination treatments. Pelleted ryegrass was sourced from a commercial supplier (Drygrass South Western Ltd, Burrington, UK). Fresh lowland grass was harvested daily in the morning from a third regrowth perennial ryegrass () sward. Fresh hill grass was harvested from a seminatural hill grassland every 2 d and stored in plastic bags at 4 to 5°C until offered. The animals were individually housed in pens and offered experimental diets for 14 d before being transferred to 6 individual respiration chambers for a further 4 d, during which feed intake, fecal and urine outputs, and CH emissions were measured. There was no interaction between genotype and forage types on any variable measured. In a comparison of effects of the 3 forages, pelleted ryegrass had the greatest ( < 0.001) values in DMI, GE intake, CH emissions, N intake (NI), and fecal N (FN), urine N (UN), and manure N (MN) outputs, whereas hill grass had the lowest ( < 0.001) values in DMI, energy (GE, DE, and ME) intake, CH emissions, NI, UN, and MN. However, pelleted ryegrass had the lowest ratio in CH emissions per unit DMI ( = 0.022) or GE intake ( = 0.026) or UN excretion as a proportion of NI or MN ( < 0.001). Lowland grass had a greater ( < 0.001) digestibility of DM, OM, CP, NDF, ADF, and GE and a greater ( < 0.001) ME:GE ratio or retained N:NI ratio than pelleted ryegrass and hill grass. Genotypes of sheep had no effect on any variable in feed intake, digestibility, CH emissions, or N utilization. The CH conversion factors (CH energy/GE) for pelleted ryegrass, lowland grass, and hill grass were 4.4, 5.7, and 5.6%, respectively. All data were then pooled to develop regression equations between CH and DMI or between N excretions (FN, UN, and MN) and NI. Methane emissions and N excretions were positively related to DMI and NI ( < 0.001), respectively. However, increasing DMI could reduce CH emissions per kilogram DMI. These equations add new information in predicting enteric CH emissions and N utilization efficiency and can be used to quantify the environmental footprint of hill sheep production systems.

Localization and characterization of (/sup 3/H)desmethylimipramine binding sites in rat brain by quantitative autoradiography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Biegon, A.; Rainbow, T.C.

1983-05-01

The high affinity binding sites for the antidepressant desmethlyimipramine (DMI) have been localized in rat brain by quantitative autoradiography. There are high concentrations of binding sites in the locus ceruleus, the anterior ventral thalamus, the ventral portion of the bed nucleus of the stria terminalis, the paraventricular and the dorsomedial nuclei of the hypothalamus. The distribution of DMI binding sites is in striking accord with the distribution of norepinephrine terminals. Pretreatment of rats with the neurotoxin 6-hydroxydopamine, which causes a selective degeneration of catecholamine terminals, results in 60 to 90% decrease in DMI binding. These data support the idea thatmore » high affinity binding sites for DMI are located on presynaptic noradrenergic terminals.« less

Orchard factors associated with resistance and cross resistance to sterol demethylation inhibitor fungicides in populations of Venturia inaequalis from Pennsylvania.

PubMed

Pfeufer, Emily E; Ngugi, Henry K

2012-03-01

Orchard management practices, such as destroying of overwintered inoculum and limiting the number of fungicide applications, are often recommended as tactics for slowing the development of resistance to sterol demethylation-inhibitor (DMI) fungicides in populations of Venturia inaequalis. However, there is little quantitative evidence relating the use of such practices to levels of resistance in orchards. The aim of this study was to evaluate the sensitivity of V. inaequalis isolates from Pennsylvania to DMI fungicides, and to identify orchard management factors related to the incidence of resistant isolates. In total, 644 single-spore V. inaequalis cultures obtained from 20 apple orchards in 2008 or 2009 were tested for sensitivity to myclobutanil, fenbuconazole, or difenoconazole. Growers provided management history of the sampled plots. Widespread shifts toward resistance to the three fungicides were noted, with mean effective concentration for 50% inhibition (EC(50)) values of 2.136, 0.786, and 0.187 μg/ml for myclobutanil, fenbuconazole, and difenoconazole, respectively. Cross resistance to the three fungicides was documented in high correlation (Spearman's r > 0.6) between mean EC(50) values for 14 orchards. Based on a 0.5-μg/ml threshold, 66 and 26% of isolates were resistant to myclobutanil and fenbuconazole, respectively, and 22% were cross resistant to the two fungicides. A significant between-year shift toward increased resistance was noted in two of three orchards surveyed in both years. Failure to use dormant copper sprays, older trees, larger orchards, orchards with ≤10 cultivars, and application of >4 DMI sprays were positively correlated (0.0001 < P < 0.05) with the incidence of resistant isolates. Isolates from orchards with >4 DMI sprays were four times as likely to be resistant to fenbuconazole (odds ratio = 4.57; P = 0.015). Isolates from orchards without dormant copper sprays were twice as likely to be cross-shifted toward resistance to all three fungicides (odds ratio = 1.76; P = 0.048). Results identify management practices that can reduce the risk of V. inaequalis developing resistance to DMI fungicides.

Prediction of water intake and excretion flows in Holstein dairy cows under thermoneutral conditions.

PubMed

Khelil-Arfa, H; Boudon, A; Maxin, G; Faverdin, P

2012-10-01

The increase in the worldwide demand for dairy products, associated with global warming, will emphasize the issue of water use efficiency in dairy systems. The evaluation of environmental issues related to the management of animal dejections will also require precise biotechnical models that can predict effluent management in farms. In this study, equations were developed and evaluated for predicting the main water flows at the dairy cow level, based on parameters related to cow productive performance and diet under thermoneutral conditions. Two datasets were gathered. The first one comprised 342 individual measurements of water balance in dairy cows obtained during 18 trials at the experimental farm of Méjussaume (INRA, France). Predictive equations of water intake, urine and fecal water excretion were developed by multiple regression using a stepwise selection of regressors from a list of seven candidate parameters, which were milk yield, dry matter intake (DMI), body weight, diet dry matter content (DM), proportion of concentrate (CONC) and content of crude protein (CP) ingested with forage and concentrate (CPf and CPc, g/kg DM). The second dataset was used for external validation of the developed equations and comprised 196 water flow measurements on experimental lots obtained from 43 published papers related to water balance or digestibility measurements in dairy cows. Although DMI was the first predictor of the total water intake (TWI), with a partial r(2) of 0.51, DM was the first predictive parameter of free water intake (FWI), with a partial r(2) of 0.57, likely due to the large variability of DM in the first dataset (from 11.5 to 91.4 g/100 g). This confirmed the compensation between water drunk and ingested with diet when DM changes. The variability of urine volume was explained mainly by the CPf associated with DMI (r.s.d. 5.4 kg/day for an average flow of 24.0 kg/day) and that of fecal water was explained by the proportion of CONC in the diet and DMI. External validation showed that predictive equations excluding DMI as predictive parameters could be used for FWI, urine and fecal water predictions if cows were fed a well-known total mixed ration. It also appeared that TWI and FWI were underestimated when ambient temperature increased above 25°C and possible means of including climatic parameters in future predictive equations were proposed.

Electrostatic Levitation Furnace for the ISS

NASA Technical Reports Server (NTRS)

Murakami, Keiji; Koshikawa, Naokiyo; Shibasaki, Kohichi; Ishikawa, Takehiko; Okada, Junpei; Takada, Tetsuya; Arai, Tatsuya; Fujino, Naoki; Yamaura, Yukiko

2012-01-01

JAXA (Japan Aerospace Exploration Agency) has just started the development of Electrostatic Levitation Furnace to be launched in 2014 for the ISS. This furnace can control the sample position with electrostatic force and heat it above 2000 degree Celsius using semiconductor laser from four different directions. The announcement of Opportunity will be issued soon for this furnace. In this paper, we will show the specifications of this furnace and also the development schedule

Methane emissions changed nonlinearly with graded substitution of alfalfa silage with corn silage and corn grain in the diet of sheep and relation with rumen fermentation characteristics in vivo and in vitro.

PubMed

Jonker, A; Lowe, K; Kittelmann, S; Janssen, P H; Ledgard, S; Pacheco, D

2016-08-01

Feeding grain and corn silage have been proposed as practices to reduce enteric methane (CH) emissions per unit of intake from ruminants, but the inclusion level required in the diet is normally not specified. The objectives of the current study were to determine the CH emission factor (g/kg DMI) of sheep fed alfalfa silage substituted with increasing levels of corn silage or corn grain at a fixed DMI level (2% of BW) and determine its relationship with rumen fermentation characteristics and microbial community composition and with in vitro fermentation characteristics of the same diets incubated using a standard laboratory method. Romney ewe hoggets (approximately 14 mo old; = 64) were randomly allocated to 8 dietary treatments, which included chaffed alfalfa silage alone or substituted with either 25, 50, 75 or 100% corn silage or 25, 50 or 65% rolled corn grain on a DM basis. After acclimatization to the diet, DMI and CH emissions were measured from individual sheep for 2 consecutive days in open-circuit respiration chambers and a rumen sample was collected at 3 h after feeding. The same diets were also incubated in an automated in vitro gas production system for 48 h using rumen liquid of fistulated nonlactating dairy cows grazing pasture. Increasing the substitution of alfalfa silage with corn silage or corn grain in the diet of sheep resulted in a quadratic response ( < 0.01) in CH emissions per unit of DMI (CH/DMI) with either supplement. For both supplements, CH/DMI increased in mixtures of up to 50% supplement inclusion and then decreased with greater supplement inclusion, especially with corn grain inclusion, but the level did not fall below that for 100% alfalfa silage. The ratio of acetate + butyrate to propionate + valerate and the propionate proportion alone in rumen liquid were the strongest single predictors for CH/DMI in the overall data set and explained 37.1 and 32.5%, respectively, of the variation in CH/DMI. Methanogens of (21.1% of total methanogens; = 0.247) and (10.7% of total methanogens; = -0.411) clades had weak to moderate correlations with in vivo CH/DMI. There was a weak quadratic relationship ( < 0.35) between in vivo CH/DMI and the in vitro parameters of gas and CH production and total VFA, whereas there was a moderate relationship ( = -0.50) between in vivo CH/estimated rumen degradable carbohydrates and in vitro CH/DM. In conclusion, CH/DMI changed in a nonlinear fashion with increasing supplement inclusion in the alfalfa forage diet when fed at 2% of BW to sheep; however, implications on predicting its influence on greenhouse gas emissions per unit of animal product, for whole farm emissions in life cycle analysis or total national emissions in the national inventories, should be determined.

A Medicago truncatula Tobacco Retrotransposon Insertion Mutant Collection with Defects in Nodule Development and Symbiotic Nitrogen Fixation1[W][OA

PubMed Central

Pislariu, Catalina I.; D. Murray, Jeremy; Wen, JiangQi; Cosson, Viviane; Muni, RajaSekhara Reddy Duvvuru; Wang, Mingyi; A. Benedito, Vagner; Andriankaja, Andry; Cheng, Xiaofei; Jerez, Ivone Torres; Mondy, Samuel; Zhang, Shulan; Taylor, Mark E.; Tadege, Million; Ratet, Pascal; Mysore, Kirankumar S.; Chen, Rujin; Udvardi, Michael K.

2012-01-01

A Tnt1-insertion mutant population of Medicago truncatula ecotype R108 was screened for defects in nodulation and symbiotic nitrogen fixation. Primary screening of 9,300 mutant lines yielded 317 lines with putative defects in nodule development and/or nitrogen fixation. Of these, 230 lines were rescreened, and 156 lines were confirmed with defective symbiotic nitrogen fixation. Mutants were sorted into six distinct phenotypic categories: 72 nonnodulating mutants (Nod−), 51 mutants with totally ineffective nodules (Nod+ Fix−), 17 mutants with partially ineffective nodules (Nod+ Fix+/−), 27 mutants defective in nodule emergence, elongation, and nitrogen fixation (Nod+/− Fix−), one mutant with delayed and reduced nodulation but effective in nitrogen fixation (dNod+/− Fix+), and 11 supernodulating mutants (Nod++Fix+/−). A total of 2,801 flanking sequence tags were generated from the 156 symbiotic mutant lines. Analysis of flanking sequence tags revealed 14 insertion alleles of the following known symbiotic genes: NODULE INCEPTION (NIN), DOESN’T MAKE INFECTIONS3 (DMI3/CCaMK), ERF REQUIRED FOR NODULATION, and SUPERNUMERARY NODULES (SUNN). In parallel, a polymerase chain reaction-based strategy was used to identify Tnt1 insertions in known symbiotic genes, which revealed 25 additional insertion alleles in the following genes: DMI1, DMI2, DMI3, NIN, NODULATION SIGNALING PATHWAY1 (NSP1), NSP2, SUNN, and SICKLE. Thirty-nine Nod− lines were also screened for arbuscular mycorrhizal symbiosis phenotypes, and 30 mutants exhibited defects in arbuscular mycorrhizal symbiosis. Morphological and developmental features of several new symbiotic mutants are reported. The collection of mutants described here is a source of novel alleles of known symbiotic genes and a resource for cloning novel symbiotic genes via Tnt1 tagging. PMID:22679222

A Medicago truncatula tobacco retrotransposon insertion mutant collection with defects in nodule development and symbiotic nitrogen fixation.

PubMed

Pislariu, Catalina I; Murray, Jeremy D; Wen, JiangQi; Cosson, Viviane; Muni, RajaSekhara Reddy Duvvuru; Wang, Mingyi; Benedito, Vagner A; Andriankaja, Andry; Cheng, Xiaofei; Jerez, Ivone Torres; Mondy, Samuel; Zhang, Shulan; Taylor, Mark E; Tadege, Million; Ratet, Pascal; Mysore, Kirankumar S; Chen, Rujin; Udvardi, Michael K

2012-08-01

A Tnt1-insertion mutant population of Medicago truncatula ecotype R108 was screened for defects in nodulation and symbiotic nitrogen fixation. Primary screening of 9,300 mutant lines yielded 317 lines with putative defects in nodule development and/or nitrogen fixation. Of these, 230 lines were rescreened, and 156 lines were confirmed with defective symbiotic nitrogen fixation. Mutants were sorted into six distinct phenotypic categories: 72 nonnodulating mutants (Nod-), 51 mutants with totally ineffective nodules (Nod+ Fix-), 17 mutants with partially ineffective nodules (Nod+ Fix+/-), 27 mutants defective in nodule emergence, elongation, and nitrogen fixation (Nod+/- Fix-), one mutant with delayed and reduced nodulation but effective in nitrogen fixation (dNod+/- Fix+), and 11 supernodulating mutants (Nod++Fix+/-). A total of 2,801 flanking sequence tags were generated from the 156 symbiotic mutant lines. Analysis of flanking sequence tags revealed 14 insertion alleles of the following known symbiotic genes: NODULE INCEPTION (NIN), DOESN'T MAKE INFECTIONS3 (DMI3/CCaMK), ERF REQUIRED FOR NODULATION, and SUPERNUMERARY NODULES (SUNN). In parallel, a polymerase chain reaction-based strategy was used to identify Tnt1 insertions in known symbiotic genes, which revealed 25 additional insertion alleles in the following genes: DMI1, DMI2, DMI3, NIN, NODULATION SIGNALING PATHWAY1 (NSP1), NSP2, SUNN, and SICKLE. Thirty-nine Nod- lines were also screened for arbuscular mycorrhizal symbiosis phenotypes, and 30 mutants exhibited defects in arbuscular mycorrhizal symbiosis. Morphological and developmental features of several new symbiotic mutants are reported. The collection of mutants described here is a source of novel alleles of known symbiotic genes and a resource for cloning novel symbiotic genes via Tnt1 tagging.

Micromagnetic study of skyrmion stability in confined magnetic structures with perpendicular anisotropy

NASA Astrophysics Data System (ADS)

Novak, R. L.; Garcia, F.; Novais, E. R. P.; Sinnecker, J. P.; Guimarães, A. P.

2018-04-01

Skyrmions are emerging topological spin structures that are potentially revolutionary for future data storage and spintronics applications. The existence and stability of skyrmions in magnetic materials is usually associated to the presence of the Dzyaloshinskii-Moriya interaction (DMI) in bulk magnets or in magnetic thin films lacking inversion symmetry. While some methods have already been proposed to generate isolated skyrmions in thin films with DMI, a thorough study of the conditions under which the skyrmions will remain stable in order to be manipulated in an integrated spintronic device are still an open problem. The stability of such structures is believed to be a result of ideal combinations of perpendicular magnetic anisotropy (PMA), DMI and the interplay between geometry and magnetostatics. In the present work we show some micromagnetic results supporting previous experimental observations of magnetic skyrmions in spin-valve stacks with a wide range of DMI values. Using micromagnetic simulations of cobalt-based disks, we obtain the magnetic ground state configuration for several values of PMA, DMI and geometric parameters. Skyrmion numbers, corresponding to the topological charge, are calculated in all cases and confirm the occurrence of isolated, stable, axially symmetric skyrmions for several combinations of DMI and anisotropy constant. The stability of the skyrmions in disks is then investigated under magnetic field and spin-polarized current, in finite temperature, highlighting the limits of applicability of these spin textures in spintronic devices.

Breeding maize as biogas substrate in Central Europe: I. Quantitative-genetic parameters for testcross performance.

PubMed

Grieder, Christoph; Dhillon, Baldev S; Schipprack, Wolfgang; Melchinger, Albrecht E

2012-04-01

Biofuels have gained importance recently and the use of maize biomass as substrate in biogas plants for production of methane has increased tremendously in Germany. The objectives of our research were to (1) estimate variance components and heritability for different traits relevant to biogas production in testcrosses (TCs) of maize, (2) study correlations among traits, and (3) discuss strategies to breed maize as a substrate for biogas fermenters. We evaluated 570 TCs of 285 diverse dent maize lines crossed with two flint single-cross testers in six environments. Data were recorded on agronomic and quality traits, including dry matter yield (DMY), methane fermentation yield (MFY), and methane yield (MY), the product of DMY and MFY, as the main target trait. Estimates of variance components showed general combining ability (GCA) to be the major source of variation. Estimates of heritability exceeded 0.67 for all traits and were even much greater in most instances. Methane yield was perfectly correlated with DMY but not with MFY, indicating that variation in MY is primarily determined by DMY. Further, DMY had a larger heritability and coefficient of genetic variation than MFY. Hence, for improving MY, selection should primarily focus on DMY rather than MFY. Further, maize breeding for biogas production may diverge from that for forage production because in the former case, quality traits seem to be of much lower importance.

Ab initio studies of 1,3,5,7-tetranitro-1,3,5,7-tetrazocine/1,3-dimethyl-2-imidazolidinone cocrystal under high pressure using dispersion corrected density functional theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gu, Bang-Ming; Lin, He; Zhu, Shun-Guan, E-mail: zhusguan@yahoo.com

A detailed study of structural, electronic, and thermodynamic properties of 1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX)/1,3-dimethyl-2-imidazolidinone (DMI) cocrystal under the hydrostatic pressure of 0–100 GPa was performed by using dispersion-corrected density functional theory (DFT-D) method. The calculated crystal structure is in reasonable agreement with the experimental data at the ambient pressure. Based on the analysis of lattice constants, bond lengths, bond angles, and dihedral angles under compression, it is found that HMX molecules in HMX/DMI cocrystal are seriously distorted. In addition, as the pressure increases, the band gap decreases gradually, which suggests that HMX/DMI cocrystal is becoming more metallic. Some important intermolecular interactions between HMXmore » and DMI are also observed in the density of states spectrum. Finally, its thermodynamic properties were characterized, and the results show that HMX/DMI cocrystal is more easily formed in the low pressure.« less

Domain walls and Dzyaloshinskii-Moriya interaction in epitaxial Co/Ir(111) and Pt/Co/Ir(111)

NASA Astrophysics Data System (ADS)

Perini, Marco; Meyer, Sebastian; Dupé, Bertrand; von Malottki, Stephan; Kubetzka, André; von Bergmann, Kirsten; Wiesendanger, Roland; Heinze, Stefan

2018-05-01

We use spin-polarized scanning tunneling microscopy and density functional theory (DFT) to study domain walls (DWs) and the Dzyaloshinskii-Moriya interaction (DMI) in epitaxial films of Co/Ir(111) and Pt/Co/Ir(111). Our measurements reveal DWs with fixed rotational sense for one monolayer of Co on Ir, with a wall width around 2.7 nm. With Pt islands on top, we observe that the DWs occur mostly in the uncovered Co/Ir areas, suggesting that the wall energy density is higher in Pt/Co/Ir(111). From DFT we find an interfacial DMI that stabilizes Néel-type DWs with clockwise rotational sense. The calculated DW widths are in good agreement with the experimental observations. The calculated total DMI nearly doubles from Co/Ir(111) to Pt/Co/Ir(111); however, in the latter case the DMI is almost entirely due to the Pt with only a minor Ir contribution. Therefore a simple additive effect, in which both interfaces contribute significantly to the total DMI, is not observed for one atomic Co layer sandwiched between Ir and Pt.

Prevalence and risk factors for diabetic retinopathy in Asian Indians with young onset type 1 and type 2 diabetes.

PubMed

Rajalakshmi, Ramachandran; Amutha, Anandakumar; Ranjani, Harish; Ali, Mohammed K; Unnikrishnan, Ranjit; Anjana, Ranjit Mohan; Narayan, K M Venkat; Mohan, Viswanathan

2014-01-01

To assess the prevalence and risk factors for diabetic retinopathy (DR) in people with young onset type 1 (T1DM-Y) and type 2 diabetes (T2DM-Y). T1DM-Y(n=150) and T2DM-Y(n=150) participants, age between 10 and 25 years at diagnosis, had a complete clinical evaluation, biochemical assessment, and four field digital retinal colour photography. The Early Treatment Diabetic Retinopathy Study grading system was used to grade DR. Proliferative diabetic retinopathy (PDR) and diabetic macular edema (DME) were considered as sight threatening DR. The prevalence of any DR was 53.3% [95% CI 45.3-61.3] in T1DM-Y (duration of diabetes: 12.4±7.4 years) and 52.7% [44.7-60.7] in T2DM-Y (11.8±8.3 years). The age and gender adjusted prevalence of DR, DME and PDR was 62.5%, 10% and 7.3% in T1DM-Y, whereas it was 65.8%,12.7% and 9.3% in T2DM-Y respectively. In multivariable logistic regression, diabetes duration [Odds ratio (OR) 1.99 per 5 years; CI 1.42-2.79], waist circumference [1.28 per 5 cm;1.05-1.56] and microalbuminuria [2.39 per 50 μg;1.07-5.31] were associated with DR in T1DM-Y, and diabetes duration [2.21 per 5 years; 1.61-3.02], diastolic blood pressure [1.54 per 5 mmHg;1.18-2.02], Glycated hemoglobin [1.37 per %;1.07-1.75] and lower stimulated C-peptide [1.54 per 0.5 pmol/ml;1.15-2.05;] were associated with DR in T2DM-Y. Over half of the people with young-onset diabetes, regardless of type, have retinopathy within 10-12 years of diabetes duration, emphasizing the need for regular eye screening and aggressive control of glucose and blood pressure to prevent DR. Copyright © 2014 Elsevier Inc. All rights reserved.

Genetic parameters of rumination time and feed efficiency traits in primiparous Holstein cows under research and commercial conditions.

PubMed

Byskov, M V; Fogh, A; Løvendahl, P

2017-12-01

Feed efficiency has the potential to be improved both through feeding, management, and breeding. Including feed efficiency in a selection index is limited by the fact that dry matter intake (DMI) recording is only feasible under research facilities, resulting in small data sets and, consequently, uncertain genetic parameter estimates. As a result, the need to record DMI indicator traits on a larger scale exists. Rumination time (RT), which is already recorded in commercial dairy herds by a sensor-based system, has been suggested as a potential DMI indicator. However, RT can only be a DMI indicator if it is heritable, correlates with DMI, and if the genetic parameters of RT in commercial herd settings are similar to those in research facilities. Therefore, the objective of our study was to estimate genetic parameters for RT and the related traits of DMI in primiparous Holstein cows, and to compare genetic parameters of rumination data between a research herd and 72 commercial herds. The estimated heritability values were all moderate for DMI (0.32-0.49), residual feed intake (0.23-0.36), energy-corrected milk (ECM) yield (0.49-0.70), and RT (0.14-0.44) found in the research herd. The estimated heritability values for ECM were lower for the commercial herds (0.08-0.35) than that for the research herd. The estimated heritability values for RT were similar for the 2 herd types (0.28-0.32). For the research herd, we found negative individual level correlations between RT and DMI (-0.24 to -0.09) and between RT and RFI (-0.34 to -0.03), and we found both positive and negative correlations between RT and ECM (-0.08 to 0.09). For the commercial herds, genetic correlations between RT and ECM were both positive and negative (-0.27 to 0.10). In conclusion, RT was not found to be a suitable indicator trait for feed intake and only a weak indicator of feed efficiency. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Toxic-Waste Disposal by Drain-in-Furnace Technique

NASA Technical Reports Server (NTRS)

Compton, L. E.; Stephens, J. B.; Moynihan, P. I.; Houseman, J.; Kalvinskas, J. J.

1986-01-01

Compact furnace moved from site to site. Toxic industrial waste destroyed using furnace concept developed for disposal of toxic munitions. Toxic waste drained into furnace where incinerated immediately. In furnace toxic agent rapidly drained and destroyed in small combustion chamber between upper and lower layers of hot ceramic balls

Using Respondent-Driven Sampling to Recruit Illegal Drug Purchasers to Evaluate a Drug Market Intervention.

PubMed

Ober, Allison J; Sussell, Jesse; Kilmer, Beau; Saunders, Jessica; Heckathorn, Douglas D

2016-04-01

Violent drug markets are not as prominent as they once were in the United States, but they still exist and are associated with significant crime and lower quality of life. The drug market intervention (DMI) is an innovative strategy that uses focused deterrence, community engagement, and incapacitation to reduce crime and disorder associated with these markets. Although studies show that DMI can reduce crime and overt drug activity, one perspective is prominently missing from these evaluations: those who purchase drugs. This study explores the use of respondent-driven sampling (RDS)-a statistical sampling method-to approximate a representative sample of drug users who purchased drugs in a targeted DMI market to gain insight into the effect of a DMI on market dynamics. Using RDS, we recruited individuals who reported hard drug use (crack or powder cocaine, heroin, methamphetamine, or illicit use of prescriptions opioids) in the last month to participate in a survey. The main survey asked about drug use, drug purchasing, and drug market activity before and after DMI; a secondary survey asked about network characteristics and recruitment. Our sample of 212 respondents met key RDS assumptions, suggesting that the characteristics of our weighted sample approximate the characteristics of the drug user network. The weighted estimates for market purchasers are generally valid for inferences about the aggregate population of customers, but a larger sample size is needed to make stronger inferences about the effects of a DMI on drug market activity. © The Author(s) 2016.

Using the Small Ruminant Nutrition System to develop and evaluate an alternative approach to estimating the dry matter intake of goats when accounting for ruminal fiber stratification.

PubMed

Regadas Filho, J G L; Tedeschi, L O; Cannas, A; Vieira, R A M; Rodrigues, M T

2014-11-01

The first objective of this research was to assess the ability of the Small Ruminant Nutrition System (SRNS) mechanistic model to predict metabolizable energy intake (MEI) and milk yield (MY) when using a heterogeneous fiber pool scenario (GnG1), compared with a traditional, homogeneous scenario (G1). The second objective was to evaluate an alternative approach to estimating the dry matter intake (DMI) of goats to be used in the SRNS model. The GnG1 scenario considers an age-dependent fractional transference rate for fiber particles from the first ruminal fiber pool (raft) to an escapable pool (λr), and that this second ruminal fiber pool (i.e., escapable pool) follows an age-independent fractional escape rate for fiber particles (ke). Scenario G1 adopted only a single fractional passage rate (kp). All parameters were estimated individually by using equations published in the literature, except for 2 passage rate equations in the G1 scenario: 1 developed with sheep data (G1-S) and another developed with goat data (G1-G). The alternative approach to estimating DMI was based on an optimization process using a series of dietary constraints. The DMI, MEI, and MY estimated for the GnG1 and G1 scenarios were compared with the results of an independent dataset (n=327) that contained information regarding DMI, MEI, MY, and milk and dietary compositions. The evaluation of the scenarios was performed using the coefficient of determination (R(2)) between the observed and predicted values, mean bias (MB), bias correction factor (Cb), and concordance correlation coefficient. The MEI estimated by the GnG1 scenario yielded precise and accurate values (R(2) = 082; MB = 0.21 Mcal/d; Cb = 0.98) similar to those of the G1-S (R(2) = 0.85; MB = 0.10 Mcal/d; Cb=0.99) and G1-G (R(2) = 0.84; MB = 0.18 Mcal/d; Cb = 0.98) scenarios. The results were also similar for the MY, but a substantial MB was found as follows: GnG1 (R(2) = 0.74; MB = 0.70 kg/d; Cb = 0.79), G1-S (R(2) = 0.71; MB = 0.58 kg/d(1); Cb = 0.85) and G1-G (R(2) = 0.71; MB = 0.65 kg/d; Cb = 0.82). The alternative approach for DMI prediction provided better results with the G1-G scenario (R(2)=0.88; MB = -71.67 g/d; Cb = 0.98). We concluded that the GnG1 scenario is valid within mechanistic models such as the SRNS and that the alternative approach for estimating DMI is reasonable and can be used in diet formulations for goats. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Evaluation of the effect of alternative measurements of body weight gain and dry matter intake for the calculation of residual feed intake in growing purebred Charolais and Red Angus cattle.

PubMed

Kayser, W; Glaze, J B; Welch, C M; Kerley, M; Hill, R A

2015-07-01

The objective of this study was to determine the effects of alternative-measurements of body weight and DMI used to evaluate residual feed intake (RFI). Weaning weight (WW), ADG, and DMI were recorded on 970 growing purebred Charolais bulls (n = 519) and heifers (n = 451) and 153 Red Angus growing steers (n = 69) and heifers (n = 84) using a GrowSafe (GrowSafe, Airdrie, Alberta, Canada) system. Averages of individual DMI were calculated in 10-d increments and compared to the overall DMI to identify the magnitude of the errors associated with measuring DMI. These incremental measurements were also used in calculation of RFI, computed from the linear regression of DMI on ADG and midtest body weight0.75 (MMWT). RFI_Regress was calculated using ADG_Regress (ADG calculated as the response of BW gain and DOF) and MMWT_PWG (metabolic midweight calculated throughout the postweaning gain test), considered the control in Red Angus. A similar calculation served as control for Charolais; RFI was calculated using 2-d consecutive start and finish weights (RFI_Calc). The RFI weaning weight (RFI_WW) was calculated using ADG_WW (ADG from weaning till the final out weight of the postweaning gain test) and MMWT_WW, calculated similarly. Overall average estimated DMI was highly correlated to the measurements derived over shorter periods, with 10 d being the least correlated and 60 d being the most correlated. The ADG_Calc (calculated using 2-d consecutive start and finish weight/DOF) and ADG_WW were highly correlated in Charolais. The ADG_Regress and ADG_Calc were highly correlated, and ADG_Regress and ADG_WW were moderately correlated in Red Angus. The control measures of RFI were highly correlated with the RFI_WW in Charolais and Red Angus. The outcomes of including abbreviated period DMI in the model with the weaning weight gain measurements showed that the model using 10 d of intake (RFI WW_10) was the least correlated with the control measures. The model with 60 d of intake had the largest correlation with the control measures. The fewest measured intake days coupled with the weaning weight values providing acceptable predictive value was RFI_WW_40, being highly correlated with the control measures. As established in the literature, at least 70 d is required to accurately measure ADG. However, we conclude that a shorter period, possibly as few as 40 d is needed to accurately estimate DMI for a reliable calculation of RFI.

Effects of acetic acid or sodium acetate infused into the rumen or abomasum on feeding behavior and metabolic response of cows in the postpartum period.

PubMed

Gualdrón-Duarte, Laura B; Allen, Michael S

2018-03-01

Effects of continuous isomolar infusions of acetic acid (AcA) or sodium acetate (NAc) infused into the rumen (RU) or into the abomasum (AB) on feeding behavior, dry matter intake (DMI), and metabolic response of cows in the early postpartum period were evaluated. Six rumen-cannulated multiparous Holstein cows (11.8 ± 3.9 d in milk; mean ± SD) were utilized in a 6 × 6 Latin square design experiment balanced for carryover effects with a 2 × 3 factorial arrangement of treatments. Treatments were AcA and NAc, with sodium chloride (CON) as a control, infused at a rate of ˜0.75 mol/h (0.5 L/h) into the RU or AB for the first 8 h following feeding, with a rest day between infusion days. Treatment sequences were assigned randomly to cows. Feeding behavior was recorded by a computerized data acquisition system and blood was sampled at 0, 4, and 8 h relative to the start of infusion. We hypothesized that AcA is more hypophagic than NAc, and that infusion into the AB is more hypophagic than infusion into the RU. Dry matter intakes (DMI) for the CON treatments were similar at 6.2 kg/8 h for RU and 6.1 kg/8 h for AB, and the AcA and NAc treatments interacted with site of infusion to affect DMI. The NAc-RU treatment did not reduce DMI (7.0 kg/8 h), whereas AcA-RU (2.6 kg/8 h), AcA-AB (3.7 kg/8 h), and NAc-AB (4.0 kg/8 h) decreased DMI compared with CON. Following infusions of AcA compared with NAc, there was a residual effect on DMI for the remainder of the day, but treatments did not affect DMI during the rest day. Treatments increased plasma acetate and β-hydroxybutyrate concentrations over time (interaction) and decreased plasma insulin concentration compared with CON. Plasma glucose concentration decreased over time after AcA-AB infusion compared with other treatments and CON. Plasma nonesterified fatty acid concentration increased over time for AcA compared with NAc and CON, suggesting an increase in lipolysis to compensate the decrease in DMI. In contrast to the other treatments, NAc-RU did not decrease DMI compared with control but we cannot determine the reason for this from the data available from the current study. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

High temperature furnace modeling and performance verifications

NASA Technical Reports Server (NTRS)

Smith, James E., Jr.

1992-01-01

Analytical, numerical, and experimental studies were performed on two classes of high temperature materials processing sources for their potential use as directional solidification furnaces. The research concentrated on a commercially available high temperature furnace using a zirconia ceramic tube as the heating element and an Arc Furnace based on a tube welder. The first objective was to assemble the zirconia furnace and construct parts needed to successfully perform experiments. The 2nd objective was to evaluate the zirconia furnace performance as a directional solidification furnace element. The 3rd objective was to establish a data base on materials used in the furnace construction, with particular emphasis on emissivities, transmissivities, and absorptivities as functions of wavelength and temperature. A 1-D and 2-D spectral radiation heat transfer model was developed for comparison with standard modeling techniques, and were used to predict wall and crucible temperatures. The 4th objective addressed the development of a SINDA model for the Arc Furnace and was used to design sample holders and to estimate cooling media temperatures for the steady state operation of the furnace. And, the 5th objective addressed the initial performance evaluation of the Arc Furnace and associated equipment for directional solidification. Results of these objectives are presented.

Development and Validation of a 3-Dimensional CFB Furnace Model

NASA Astrophysics Data System (ADS)

Vepsäläinen, Arl; Myöhänen, Karl; Hyppäneni, Timo; Leino, Timo; Tourunen, Antti

At Foster Wheeler, a three-dimensional CFB furnace model is essential part of knowledge development of CFB furnace process regarding solid mixing, combustion, emission formation and heat transfer. Results of laboratory and pilot scale phenomenon research are utilized in development of sub-models. Analyses of field-test results in industrial-scale CFB boilers including furnace profile measurements are simultaneously carried out with development of 3-dimensional process modeling, which provides a chain of knowledge that is utilized as feedback for phenomenon research. Knowledge gathered by model validation studies and up-to-date parameter databases are utilized in performance prediction and design development of CFB boiler furnaces. This paper reports recent development steps related to modeling of combustion and formation of char and volatiles of various fuel types in CFB conditions. Also a new model for predicting the formation of nitrogen oxides is presented. Validation of mixing and combustion parameters for solids and gases are based on test balances at several large-scale CFB boilers combusting coal, peat and bio-fuels. Field-tests including lateral and vertical furnace profile measurements and characterization of solid materials provides a window for characterization of fuel specific mixing and combustion behavior in CFB furnace at different loads and operation conditions. Measured horizontal gas profiles are projection of balance between fuel mixing and reactions at lower part of furnace and are used together with both lateral temperature profiles at bed and upper parts of furnace for determination of solid mixing and combustion model parameters. Modeling of char and volatile based formation of NO profiles is followed by analysis of oxidizing and reducing regions formed due lower furnace design and mixing characteristics of fuel and combustion airs effecting to formation ofNO furnace profile by reduction and volatile-nitrogen reactions. This paper presents CFB process analysis focused on combustion and NO profiles in pilot and industrial scale bituminous coal combustion.

Selective Efficacy of Static and Dynamic Imagery in Different States of Physical Fatigue.

PubMed

Kanthack, Thiago Ferreira Dias; Guillot, Aymeric; Altimari, Leandro Ricardo; Nunez Nagy, Susana; Collet, Christian; Di Rienzo, Franck

2016-01-01

There is compelling evidence that motor imagery contributes to improved motor performance, and recent work showed that dynamic motor imagery (dMI) might provide additional benefits by comparison with traditional MI practice. However, the efficacy of motor imagery in different states of physical fatigue remains largely unknown, especially as imagery accuracy may be hampered by the physical fatigue states elicited by training. We investigated the effect of static motor imagery (sMI) and dMI on free-throw accuracy in 10 high-level basketball athletes, both in a non-fatigued state (Experiment 1) and immediately after an incremental running test completed until exhaustion (20 m shuttle run-test-Experiment 2). We collected perceived exhaustion and heart rate to quantify the subjective experience of fatigue and energy expenditure. We found that dMI brought better shooting performance than sMI, except when athletes were physically exhausted. These findings shed light on the conditions eliciting optimal use of sMI and dMI. In particular, considering that the current physical state affects body representation, performing dMI under fatigue may result in mismatches between actual and predicted body states.

Interface control of the magnetic chirality in CoFeB/MgO heterostructures with heavy-metal underlayers.

PubMed

Torrejon, Jacob; Kim, Junyeon; Sinha, Jaivardhan; Mitani, Seiji; Hayashi, Masamitsu; Yamanouchi, Michihiko; Ohno, Hideo

2014-08-18

Recent advances in the understanding of spin orbital effects in ultrathin magnetic heterostructures have opened new paradigms to control magnetic moments electrically. The Dzyaloshinskii-Moriya interaction (DMI) is said to play a key role in forming a Néel-type domain wall that can be driven by the spin Hall torque. Here we show that the strength and sign of the DMI can be changed by modifying the adjacent heavy-metal underlayer (X) in perpendicularly magnetized X/CoFeB/MgO heterostructures. The sense of rotation of a domain wall spiral is reversed when the underlayer is changed from Hf, Ta to W and the strength of DMI varies as the filling of 5d orbitals, or the electronegativity, of the heavy-metal layer changes. The DMI can even be tuned by adding nitrogen to the underlayer, thus allowing interface engineering of the magnetic texture in ultrathin magnetic heterostructures.

Symposium review: Uncertainties in enteric methane inventories, measurement techniques, and prediction models.

PubMed

Hristov, A N; Kebreab, E; Niu, M; Oh, J; Bannink, A; Bayat, A R; Boland, T B; Brito, A F; Casper, D P; Crompton, L A; Dijkstra, J; Eugène, M; Garnsworthy, P C; Haque, N; Hellwing, A L F; Huhtanen, P; Kreuzer, M; Kuhla, B; Lund, P; Madsen, J; Martin, C; Moate, P J; Muetzel, S; Muñoz, C; Peiren, N; Powell, J M; Reynolds, C K; Schwarm, A; Shingfield, K J; Storlien, T M; Weisbjerg, M R; Yáñez-Ruiz, D R; Yu, Z

2018-04-18

Ruminant production systems are important contributors to anthropogenic methane (CH 4 ) emissions, but there are large uncertainties in national and global livestock CH 4 inventories. Sources of uncertainty in enteric CH 4 emissions include animal inventories, feed dry matter intake (DMI), ingredient and chemical composition of the diets, and CH 4 emission factors. There is also significant uncertainty associated with enteric CH 4 measurements. The most widely used techniques are respiration chambers, the sulfur hexafluoride (SF 6 ) tracer technique, and the automated head-chamber system (GreenFeed; C-Lock Inc., Rapid City, SD). All 3 methods have been successfully used in a large number of experiments with dairy or beef cattle in various environmental conditions, although studies that compare techniques have reported inconsistent results. Although different types of models have been developed to predict enteric CH 4 emissions, relatively simple empirical (statistical) models have been commonly used for inventory purposes because of their broad applicability and ease of use compared with more detailed empirical and process-based mechanistic models. However, extant empirical models used to predict enteric CH 4 emissions suffer from narrow spatial focus, limited observations, and limitations of the statistical technique used. Therefore, prediction models must be developed from robust data sets that can only be generated through collaboration of scientists across the world. To achieve high prediction accuracy, these data sets should encompass a wide range of diets and production systems within regions and globally. Overall, enteric CH 4 prediction models are based on various animal or feed characteristic inputs but are dominated by DMI in one form or another. As a result, accurate prediction of DMI is essential for accurate prediction of livestock CH 4 emissions. Analysis of a large data set of individual dairy cattle data showed that simplified enteric CH 4 prediction models based on DMI alone or DMI and limited feed- or animal-related inputs can predict average CH 4 emission with a similar accuracy to more complex empirical models. These simplified models can be reliably used for emission inventory purposes. The Authors. Published by FASS Inc. and Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/).

Enhanced down regulation of cortical +-propranolol sensitive ( sup 3 H)-DHA binding sites by co-administration of DMI and 5-HT sub 1A partial agonist gepirone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geissler, M.A.; Yocca, F.D.

1990-02-26

The putative interrelationship between the noradrenergic and serotonergic systems has been supported by numerous studies. Recently, Dudley et al. (1989) demonstrated significant down regulation of cortical {beta}-adrenergic receptors by co-administration of desipramine (DMI), a norepinephrine uptake inhibitor, and the full 5-HT{sub 1A} agonist 8-OH-DPAT. To this end, the effects of acute and chronic (4 and 14 day) administration of DMI, gepirone, a selective 5-HT{sub 1A} post-synaptic partial agonist, as well as a combination of the two, on cortical ({plus minus})-propranolol sensitive ({sup 3}H)-DHA binding sites were examined in rats. Down regulation was apparent after 4 and 14 day treatment withmore » DMI. However, this was not the case with gepirone. Of particular importance is the demonstration of a greater magnitude of down regulation with co-administration of a greater magnitude of down regulation with co-administration of DMI and gepirone. These results suggests that alteration in rat cortical ({plus minus})-propranolol sensitive ({sup 3}H)-DHA binding sites by noradrenergic uptake inhibitors can be further modulated by selective partial agonist activity at central 5-HT{sub 1A} postsynaptic receptors. Further data on the co-administration of DMI and BMY 7378 (7,9-dioxo-8-(2-(4-{und o}-methoxyphenylpiperazinyl)ethyl)-8-azaspiro(4,5)decane dihydrochloride), a weak partial agonist at postsynaptic 5-HT{sub 1A} receptors, are also presented.« less

Seasonal adjustment of energy budget in a large wild mammal, the Przewalski horse (Equus ferus przewalskii) I. Energy intake.

PubMed

Kuntz, Regina; Kubalek, Christina; Ruf, Thomas; Tataruch, Frieda; Arnold, Walter

2006-11-01

Large ruminants respond to changing plant phenology during winter by decreasing voluntary food intake, increasing gut passage time and utilizing body fat reserves. It is uncertain, however, how other large mammals with a non-ruminant digestive physiology cope with winter forage conditions. Therefore, we investigated seasonality of energy intake in a large herbivorous wild mammal, the Przewalski horse (Equus ferus przewalskii). Throughout all seasons we used the n-alkane method to measure daily dry matter intake (DMI), diet composition and digestion, and determined an index of gut passage time in horses living under close to natural conditions. DMI correlated positively with its content of crude protein and nitrogen-free extract. Independent of these effects, DMI further varied seasonally with a peak in autumn and a nadir in late winter. Fluctuations of DMI corresponded to the annual change in body condition, which decreased during winter while energy reserves were depleted, and increased during the fattening period. Gut passage time varied in the course of the year and was longer during winter when the diet was high in crude fibre. Nevertheless, changes in gut passage time occurred rather independently of changes in forage composition and DMI, suggesting endogenous control for timely adaption of the digestive strategy to meet predictable changes in forage quality.

Mesoscale influence on long-range transport — evidence from ETEX modelling and observations

NASA Astrophysics Data System (ADS)

Sørensen, Jens Havskov; Rasmussen, Alix; Ellermann, Thomas; Lyck, Erik

During the first European Tracer Experiment (ETEX) tracer gas was released from a site in Brittany, France, and subsequently observed over a range of 2000 km. Hourly measurements were taken at the National Environmental Research Institute (NERI) located at Risø, Denmark, using two measurement techniques. At this location, the observed concentration time series shows a double-peak structure occurring between two and three days after the release. By using the Danish Emergency Response Model of the Atmosphere (DERMA), which is developed at the Danish Meteorological Institute (DMI), simulations of the dispersion of the tracer gas have been performed. Using numerical weather-prediction data from the European Centre for Medium-Range Weather Forecast (ECMWF) by DERMA, the arrival time of the tracer is quite well predicted, so also is the duration of the passage of the plume, but the double-peak structure is not reproduced. However, using higher-resolution data from the DMI version of the HIgh Resolution Limited Area Model (DMI-HIRLAM), DERMA reproduces the observed structure very well. The double-peak structure is caused by the influence of a mesoscale anti-cyclonic eddy on the tracer gas plume about one day earlier.

Aspects of Dzyaloshinskii-Moriya Interaction in Two Dimensional Magnetic Structures

NASA Astrophysics Data System (ADS)

Kundu, Anirban

Research on topologically protected chiral magnetic structures such as magnetic domain walls (DWs) and skyrmions, have gained extensive interest because of their possible applications in magnetic data storage industries. The recently observed chiral DW structures in ultrathin ferromagnetic lms with perpendicular magnetic anisotropy has been attributed to the presence of a strong Dzyaloshinskii-Moriya interaction (DMI). In this thesis, the DMI mediated by the conduction electrons in two dimensional magnetic systems such as magnetic thin lms or at the interfaces between two magnetic materials has been studied. I calculate the Ruderman-Kittel- Kasuya-Yosida (RKKY) type indirect exchange coupling between two magnetic moments at nite temperature using the free electron band. At high temperature, the coupling strength decays with distance faster than the coupling at zero temperature but the period of oscillation remains same. However, the free electron band alone could not produce DMI. In the next step, I show addition of Rashba spin-orbit coupling (RSOC) with the spin-polarized conduction electron band produces the DMI between two magnetic ions. The essential feature of this DMI is: the coupling strength increases with the strength of RSOC, but decreases signi cantly with the Heisenberg exchange coupling. The DMI calculated with this model well explains the possibility of preferred Neel or Bloch DW structures with specifc chirality. In addition: I study switching of magnetization with ultrafast laser pulse by inverse Faraday e ect (IFE) where an optically induced non-equilibrium orbital momentum generates an e ective magnetic eld via spin-orbit coupling for magnetization switching. I calculate the magnitude of induced orbital moment for the generic itinerant band and show that magnitude is not large enough to make the switching by a single pulse, however, switching could be possible if multiple pulses are applied to the material.

Efficient 'Optical Furnace': A Cheaper Way to Make Solar Cells is Reaching the Marketplace

DOE Office of Scientific and Technical Information (OSTI.GOV)

von Kuegelgen, T.

In Bhushan Sopori's laboratory, you'll find a series of optical furnaces he has developed for fabricating solar cells. When not in use, they sit there discreetly among the lab equipment. But when a solar silicon wafer is placed inside one for processing, Sopori walks over to a computer and types in a temperature profile. Almost immediately this fires up the furnace, which glows inside and selectively heats up the silicon wafer to 800 degrees centigrade by the intense light it produces. Sopori, a principal engineer at the National Renewable Energy Laboratory, has been researching and developing optical furnace technology formore » around 20 years. He says it's a challenging technology to develop because there are many issues to consider when you process a solar cell, especially in optics. Despite the challenges, Sopori and his research team have advanced the technology to the point where it will benefit all solar cell manufacturers. They are now developing a commercial version of the furnace in partnership with a manufacturer. 'This advanced optical furnace is highly energy efficient, and it can be used to manufacture any type of solar cell,' he says. Each type of solar cell or manufacturing process typically requires a different furnace configuration and temperature profile. With NREL's new optical furnace system, a solar cell manufacturer can ask the computer for any temperature profile needed for processing a solar cell, and the same type of furnace is suitable for several solar cell fabrication process steps. 'In the future, solar cell manufacturers will only need this one optical furnace because it can be used for any process, including diffusion, metallization and oxidation,' Sopori says. 'This helps reduce manufacturing costs.' One startup company, Applied Optical Systems, has recognized the furnace's potential for manufacturing thin-film silicon cells. 'We'd like to develop thin-film silicon cells with higher efficiencies, up to 15 to 18 percent, and we believe this furnace will enable us to do so,' says A. Rangappan, founder and CEO of Applied Optical Systems. Rangappan also says it will take only a few minutes for the optical furnace to process a thin-film solar cell, which reduces manufacturing costs. Overall, he estimates the company's solar cell will cost around 80 cents per watt. For manufacturing these thin-film silicon cells, Applied Optical Systems and NREL have developed a partnership through a cooperative research and development agreement (CRADA) to construct an optical furnace system prototype. DOE is providing $500,000 from its Technology Commercialization Development Fund to help offset the prototype's development costs because of the technology's significant market potential. The program has provided the NREL technology transfer office with a total of $4 million to expand such collaborative efforts between NREL researchers and companies. Applied Optical will construct a small version of the optical furnace based on the prototype design in NREL's process development and integration laboratory through a separate CRADA. This small furnace will only develop one solar cell wafer at a time. Then, the company will construct a large, commercial-scale optical furnace at its own facilities, which will turn out around 1,000 solar cell wafers per hour. 'We hope to start using the optical furnace for manufacturing within four to five years,' Rangappan says. Meanwhile, another partnership using the optical furnace has evolved between NREL and SiXtron Advanced Materials, another startup. Together they'll use the optical furnace to optimize the metallization process for novel antireflective solar cell coatings. The process is not only expected to yield higher efficiencies for silicon-based solar cells, but also lowers processing costs and eliminates safety concerns for manufacturers. Most solar cell manufacturers currently use a plasma-enhanced chemical vapor deposition (PECVD) system with compressed and extremely pyrophoric silane gas (SiH4) for applying passivation antireflective coatings (ARC). If silane is exposed to air, the SiH4 will explode - a serious safety issue for high-volume manufacturers. SiXtron's process uses a solid, silicon-based polymer that's converted into noncompressed, nonexplosive gas, which then flows to a standard PECVD system. 'The solid source is so safe to handle that it can be shipped by FedEx,' says Zbigniew Barwicz, president and CEO of SiXtron. Barwicz says manufacturers can use the same PECVD processing equipment for the SiXtron process that they already use for SiH4, a plug-and-play solution. For this novel passivation ARC process, NREL is helping to optimize the metallization parameters. NREL has developed a new technology called optical processing. One of the applications of this process is fire-through contact formation of silicon solar cells.« less

Magnon Hall effect without Dzyaloshinskii-Moriya interaction.

PubMed

Owerre, S A

2017-01-25

Topological magnon bands and magnon Hall effect in insulating collinear ferromagnets are induced by the Dzyaloshinskii-Moriya interaction (DMI) even at zero magnetic field. In the geometrically frustrated star lattice, a coplanar/noncollinear [Formula: see text] magnetic ordering may be present due to spin frustration. This magnetic structure, however, does not exhibit topological magnon effects even with DMI in contrast to collinear ferromagnets. We show that a magnetic field applied perpendicular to the star plane induces a non-coplanar spin configuration with nonzero spin scalar chirality, which provides topological effects without the need of DMI. The non-coplanar spin texture originates from the topology of the spin configurations and does not need the presence of DMI or magnetic ordering, which suggests that this phenomenon may be present in the chiral spin liquid phases of frustrated magnetic systems. We propose that these anomalous topological magnon effects can be accessible in polymeric iron (III) acetate-a star-lattice antiferromagnet with both spin frustration and long-range magnetic ordering.

Topological magnon bands and unconventional thermal Hall effect on the frustrated honeycomb and bilayer triangular lattice.

PubMed

Owerre, S A

2017-09-27

In the conventional ferromagnetic systems, topological magnon bands and thermal Hall effect are due to the Dzyaloshinskii-Moriya interaction (DMI). In principle, however, the DMI is either negligible or it is not allowed by symmetry in some quantum magnets. Therefore, we expect that topological magnon features will not be present in those systems. In addition, quantum magnets on the triangular-lattice are not expected to possess topological features as the DMI or spin-chirality cancels out due to equal and opposite contributions from adjacent triangles. Here, however, we predict that the isomorphic frustrated honeycomb-lattice and bilayer triangular-lattice antiferromagnetic system will exhibit topological magnon bands and topological thermal Hall effect in the absence of an intrinsic DMI. These unconventional topological magnon features are present as a result of magnetic-field-induced non-coplanar spin configurations with nonzero scalar spin chirality. The relevance of the results to realistic bilayer triangular antiferromagnetic materials are discussed.

Interfacial Dzyaloshinskii-Moriya interaction, surface anisotropy energy, and spin pumping at spin orbit coupled Ir/Co interface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Nam-Hui; Jung, Jinyong; Cho, Jaehun

2016-04-04

The interfacial Dzyaloshinskii-Moriya interaction (iDMI), surface anisotropy energy, and spin pumping at the Ir/Co interface are experimentally investigated by performing Brillouin light scattering. Contrary to previous reports, we suggest that the sign of the iDMI at the Ir/Co interface is the same as in the case of the Pt/Co interface. We also find that the magnitude of the iDMI energy density is relatively smaller than in the case of the Pt/Co interface, despite the large strong spin-orbit coupling (SOC) of Ir. The saturation magnetization and the perpendicular magnetic anisotropy (PMA) energy are significantly improved due to a strong SOC. Ourmore » findings suggest that an SOC in an Ir/Co system behaves in different ways for iDMI and PMA. Finally, we determine the spin pumping effect at the Ir/Co interface, and it increases the Gilbert damping constant from 0.012 to 0.024 for 1.5 nm-thick Co.« less

The Desmethyl Metabolite of Imipramine (G-35020) in the Treatment of Depression: Further Clinical Experience

PubMed Central

Mann, Alan M.; Heseltine, G. F. D.

1963-01-01

The desmethyl metabolite of imipramine (DMI) was used to treat 103 depressed patients, standard dosage being 50 mg. thrice daily orally. Seventy patients recovered or were much improved. The indication for DMI and its activity spectrum were of the same order as imipramine. Side effects were less frequent and less severe. Average onset of definitive improvement was three days; earliest changes noted were in facies, motility, and relief of guilt feelings. Besides the classical straightforward response, seven patients improved early but relapsed, and 12 showed a “plateau effect”. Absence of favourable response after seven days necessitated reevaluation and/or substitution of other approaches. DMI may be the drug of choice in initiating treatment of depression, but seemed insufficient alone to deal with agitated, acutely suicidal patients. Although DMI appeared an effective, fast-acting antidepressant, there is still no panacea for this ubiquitous syndrome, whose proper management calls for flexibility and awareness of its multifactorial etiology. PMID:20327557

The Desmethyl Metabolite of Imipramine (G-35020) in the Treatment of Depression: Further Clinical Experience.

PubMed

Mann, A M; Heseltine, G F

1963-06-01

The desmethyl metabolite of imipramine (DMI) was used to treat 103 depressed patients, standard dosage being 50 mg. thrice daily orally. Seventy patients recovered or were much improved. The indication for DMI and its activity spectrum were of the same order as imipramine. Side effects were less frequent and less severe. Average onset of definitive improvement was three days; earliest changes noted were in facies, motility, and relief of guilt feelings. Besides the classical straightforward response, seven patients improved early but relapsed, and 12 showed a "plateau effect". Absence of favourable response after seven days necessitated reevaluation and/or substitution of other approaches. DMI may be the drug of choice in initiating treatment of depression, but seemed insufficient alone to deal with agitated, acutely suicidal patients. Although DMI appeared an effective, fast-acting antidepressant, there is still no panacea for this ubiquitous syndrome, whose proper management calls for flexibility and awareness of its multifactorial etiology.

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Ornelas-Couto, M; Bossart, E; Elsayyad, N

Purpose: To determine the sensitivity of dose-mass-histogram (DMH) due to anatomical changes of head-and-neck squamous cell carcinoma (HNSCC) radiotherapy (RT). Methods: Eight patients undergoing RT treatment for HNSCC were scanned during the third and sixth week of RT. These second (CT2) and third (CT3) CTs were co-registered to the planning CT (CT1). Contours were propagated via deformable registration from CT1 and doses were re-calculated. DMHs were extracted for each CT set. DMH sensitivity was assessed by dose-mass indices (DMIs), which represent the dose delivered to a certain mass of and anatomical structure. DMIs included: dose to 98%, 95% and 2%more » of the target masses (PTV1, PTV2, and PTV3) and organs-at-risk (OARs): cord DMI2%, brainstem DMI2%, left- and right-parotid DMI2% and DMI50%, and mandible DMI2%. A two-tailed paired t-test was used to compare changes to DMIs in CT2 and CT3 with respect to CT1 (CT2/CT1 and CT3/CT1). Results: Changes to DMHs were found for all OARs and PTVs, but they were significant only for the PTVs. Maximum dose to PTVs increased significantly for CT2/CT1 in all three PTVs, but CT3/CT1 changes were only significantly different for PTV1 and PTV2. Dose coverage to the three PTVs was also significantly different, DMI98% was lower for both CT2/CT1 and CT3/CT1. DMI95% was significantly lower for PTV1 for CT2/CT1, PTV2 for CT2/CT1 and CT3/CT1, and PTV3 for CT3/CT1. Conclusion: Changes in anatomy significantly change dose-mass coverage for the planning targets, making it necessary to re-plan in order to maintain the therapeutic goals. Maximum dose to the PTVs increase significantly as RT progresses, which may not be problematic as long as the high dose remains in the gross tumor volume. Doses to OARs were minimally affected and the differences were not significant.« less

Effects of Saccharomyces cerevisiae fermentation product on ruminal starch digestion are dependent upon dry matter intake for lactating cows.

PubMed

Allen, M S; Ying, Y

2012-11-01

This experiment was conducted to evaluate ruminal digestion responses to Saccharomyces cerevisiae fermentation product (SCFP) supplementation and to determine if responses are influenced by voluntary feed intake. Fifteen ruminally and duodenally cannulated Holstein cows with a wide range in preliminary dry matter intake (pDMI; 20.1 to 31.0 kg/d) measured during a 14-d preliminary period were used in a crossover design experiment. Treatments were SCFP and control (a mix of dry ground corn and soybean meal), top-dressed at the rate of 56 g/d per head. The base diet contained 28% NDF, 30% starch, and 16.5% CP and included corn silage, alfalfa silage, high-moisture corn, protein supplement, and a mineral and vitamin supplement. Treatment periods were 28 d, with the final 8d used for sample and data collection. Voluntary dry matter intake was determined during the last 4d of the preliminary period. Ruminal digestion kinetics were determined using the pool-and-flux method. Main effects of SCFP treatment and their interaction with pDMI were tested by ANOVA. An interaction was detected between SCFP treatment and pDMI for ruminal digestion rate of starch; SCFP increased the rate of starch digestion compared with the control for cows with pDMI below 26 kg/d and decreased it for cows with higher pDMI. This resulted in an interaction between treatment and pDMI for turnover rate of starch in the rumen and true and apparent ruminal starch digestibility because passage rate of starch from the rumen was not affected by treatment (mean=24.3%/h). Ruminal pH (mean=6.0), dry matter intake, milk yield and component percentages were not affected by treatment or its interaction with pDMI. Supplementation of SCFP reduced the rate of ruminal starch digestion for cows with higher feed intake, which could help stabilize the ruminal environment when large amounts of starch are consumed to support higher milk production. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Feasibility study of a high temperature radiation furnace for space applications

NASA Technical Reports Server (NTRS)

Eiss, A.; Dussan, B.; Shadis, W.; Frank, L.

1973-01-01

The feasibility was investigated of a high temperature general purpose furnace for use in space. It was determined that no commercial furnaces exist which could, even with extensive modifications, meet the goals of temperature, power, weight, volume, and versatility originally specified in the contract Statement of Work. A feasible furnace design which does substantially meet these goals while employing many of the advanced features of the commercial furnaces is developed and presented.

Recent developments in blast furnace process control within British Steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warren, P.W.

1995-12-01

British Steel generally operates seven blast furnaces on four integrated works. All furnaces have been equipped with comprehensive instrumentation and data logging computers over the past eight years. The four Scunthorpe furnaces practice coal injection up to 170 kg/tHM (340 lb/THM), the remainder injecting oil at up to 100 kg/tHM (200 lb/THM). Distribution control is effected by Paul Wurth Bell-Less Tops on six of the seven furnaces, and Movable Throat Armour with bells on the remaining one. All have at least one sub burden probe. The blast furnace operator has a vast quantity of data and signals to consider andmore » evaluate when attempting to achieve the objective of providing a consistent supply of hot metal. Techniques have been, and are being, developed to assist the operator to interpret large numbers of signals. A simple operator guidance system has been developed to provide advice, based on current operating procedures and interpreted data. Further development will involve the use of a sophisticated Expert System software shell.« less

Relationships of feeding behaviors with average daily gain, dry matter intake, and residual feed intake in Red Angus-sired cattle.

PubMed

McGee, M; Welch, C M; Ramirez, J A; Carstens, G E; Price, W J; Hall, J B; Hill, R A

2014-11-01

Feeding behavior has the potential to enhance prediction of feed intake and to improve understanding of the relationships between behavior, DMI, ADG, and residual feed intake (RFI) in beef cattle. Two cohorts, born in 2009 and 2010, the progeny of Red Angus bulls (n = 58 heifers and n = 53 steers), were evaluated during the growing phase, and the latter group of steers was also evaluated during the finishing phase. All behavior analyses were based on 7 feeding behavior traits (bunk visit frequency, bunk visit duration [BVDUR], feed bout frequency, feed bout duration, meal frequency, meal duration, and average meal intake) and their relationships with ADG, DMI, and RFI. During the growing phase, feeding duration traits were most indicative of DMI with positive correlations between BVDUR and DMI for cohort 1 steers, growing phase (n = 28, r = 0.52, P = 0.00); cohort 2 steers, growing phase (n = 25, r = 0.44, P = 0.01); and cohort 2 heifers, growing phase (n = 29, r = 0.28 P = 0.05). There were similar trends toward correlation of BVDUR and RFI for both steer groups and cohort 1 heifers, growing phase (C1HG; n = 29; r = 0.27, P = 0.06; r = 0.30, P = 0.07; and r = 0.26, P = 0.08, respectively). Feed bout frequency was correlated with ADG in C1HG and in cohort 2 steers, finishing phase (r = -0.31, P = 0.04, and r = 0.43, P = 0.01, respectively). Feed bout duration was correlated with ADG in heifer groups (r = 0.29 and r = 0.28, P = 0.05 for both groups) and DMI for all growing phase animals (r = 0.29 to 0.55, P ≤ 0.05 for all groups). Evaluation of growing vs. finishing phase steer groups suggests that all behaviors, RFI, and DMI, but not ADG, are correlated through the growing and finishing phases (P ≤ 0.01 for all variables excluding ADG), implying that feeding behaviors determined during the growing phase are strong predictors of DMI in either life stage. Sire maintenance energy EPD effects (measured as high or low groups) on progeny feeding behaviors revealed a difference in meal duration with a tendency to differ in average meal intake (P = 0.01 and P = 0.07, respectively). Feeding behavior duration traits may be useful predictors of DMI in Red Angus cattle.

Effects of diet forage source and neutral detergent fiber content on milk production of dairy cattle and methane emissions determined using GreenFeed and respiration chamber techniques.

PubMed

Hammond, K J; Jones, A K; Humphries, D J; Crompton, L A; Reynolds, C K

2016-10-01

Strategies to mitigate greenhouse gas emissions from dairy cattle are unlikely to be adopted if production or profitability is reduced. The primary objective of this study was to examine the effects of high maize silage (MS) versus high grass silage (GS) diets, without or with added neutral detergent fiber (NDF) on milk production and methane emission of dairy cattle, using GreenFeed (GF) or respiration chamber (RC) techniques for methane emission measurements. Experiment 1 was 12wk in duration with a randomized block continuous design and 40 Holstein cows (74d in milk) in free-stall housing, assigned to 1 of 4 dietary treatments (n=10 per treatment), according to calving date, parity, and milk yield. Milk production and dry matter intake (DMI) were measured daily, and milk composition measured weekly, with methane yield (g/kg of DMI) estimated using a GF unit (wk 10 to 12). Experiment 2 was a 4×4 Latin square design with 5-wk periods and 4 dairy cows (114d in milk) fed the same 4 dietary treatments as in experiment 1. Measurements of DMI, milk production, and milk composition occurred in wk 4, and DMI, milk production, and methane yield were measured for 2d in RC during wk 5. Dietary treatments for both experiments were fed as total mixed rations offered ad libitum and containing 500g of silage/kg of dry matter composed (DM basis) of either 75:25 MS:GS (MS) or 25:75 MS:GS (GS), without or with added NDF from chopped straw and soy hulls (+47g of NDF/kg of dry matter). In both experiments, compared with high GS, cows fed high MS had a higher DMI, greater milk production, and lower methane yield (24% lower in experiment 1 using GF and 8% lower in experiment 2 using RC). Added NDF increased (or tended to increase) methane yield for high MS, but not high GS diets. In the separate experiments, the GF and RC methods detected similar dietary treatment effects on methane emission (expressed as g/d and g/kg of DMI), although the magnitude of the differences varied between experiments. Overall methane emission and yield were 448g/d and 20.9g/kg of DMI for experiment 1 using GF and 458g/d and 23.8g/kg of DMI for experiment 2 using RC, respectively. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The effects of adding fat to diets of lactating dairy cows on total-tract neutral detergent fiber digestibility: A meta-analysis.

PubMed

Weld, K A; Armentano, L E

2017-03-01

The objective of this meta-analysis was to determine the effects of supplemental fat on fiber digestibility in lactating dairy cattle. Published papers that evaluated the effects of adding fat to the diets of lactating dairy cattle on total-tract neutral detergent fiber digestibility (ttNDFd) and dry matter intake (DMI) were compiled. The final data set included 108 fat-supplemented treatment means, not including low-fat controls, from 38 publications. The fat-supplemented treatment means exhibited a wide range of ttNDFd (49.4% ± 9.3, mean ± standard deviation) and DMI (21.3 kg/d ± 3.5). Observations were summarized as the difference between the treatment means for fat-supplemented diets minus their respective low-fat control means. Additionally, those differences were divided by the difference in diet fatty acid (FA) concentration between the treatment and control diets. Treatment means were categorized by the type of fat supplement. Supplementing 3% FA in the diet as medium-chain fats (containing predominately 12- and 14-carbon saturated FA) or unsaturated vegetable oil decreased ttNDFd by 8.0 and 1.2 percentage units, respectively. Adding 3% calcium salts of long-chain FA or saturated fats increased ttNDFd by 3.2 and 1.3 percentage units, respectively. No other fat supplement type affected ttNDFd. Except for saturated fats and animal-vegetable fats, supplementing dietary fat decreased DMI. When the values for changes in ttNDFd are regressed on changes in DMI there was a positive relationship, though the coefficient of determination is only 0.20. When changes in ttNDFd were regressed on changes in DMI, within individual fat supplement types, there was no relationship within calcium salt supplements. There was a positive relationship between changes in ttNDFd and changes in DMI for saturated fats. Neither relationship suggested that the increased ttNDFd with calcium salts or saturated FA was due to decreased DMI for these fat sources. A subset of the means included measured ruminal neutral detergent fiber digestion. Analysis of this smaller data set did not suggest that ruminal neutral detergent fiber digestibility is depressed by fat supplementation more than ttNDFd. Adding fats, other than those with medium-chain FA, consistently increased digestible energy density of the diet. However, due to reduced DMI, this increased energy density may not result in increased digestible nutrient intake. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Therapeutic value of lymphadenectomy and adjuvant radiotherapy in uterine corpus confined endometrioid-type cancer.

PubMed

Turan, Taner; Kimyon Comert, Gunsu; Turkmen, Osman; Ureyen, Isin; Fadiloglu, Erdem; Karalok, Alper; Tasci, Tolga; Tulunay, Gokhan; Basaran, Derman

2017-12-26

To determine the efficacy of lymphadenectomy and adjuvant radiotherapy in patients with endometrioid-type cancer confined to the uterine corpus. A total of 323 patients were evaluated. Patients were stratified according to depth of myometrial invasion (DMI) and tumor grade. Lymphadenectomy was performed in 83% of the entire cohort. Age (<60 vs. ≥60) and DMI affected disease-free survival. Addition of lymphadenectomy improved the disease-specific survival. The improved effect of lymphadenectomy was only observed in DMI ≥½ and grade 2 tumor (78.5% vs. 95.4%). However, that effect in this group was determined in patients with more than 50 removed lymph nodes. Performing adjuvant radiotherapy and the type of the radiotherapy (vaginal brachytherapy vs. external beam radiotherapy) were not significant for disease-free and disease-specific survival. In the entire cohort, loco-regional recurrence occurred in 3.1% and 4.4% of patients with or without adjuvant radiotherapy, respectively. However, these rates were 2.6% and 13.6% for patients with DMI ≥½ and grade 2 who were older than 60 years, respectively. Lymphadenectomy should be performed in patients with DMI ≥½ and grade 2 to improve survival. Adjuvant vaginal brachytherapy may only be given to patients who are older than 60 years old with moderate differentiation and deep myometrial invasion to reduce loco-regional recurrence. Copyright © 2017. Published by Elsevier Taiwan LLC.

Integration of Tuyere, Raceway and Shaft Models for Predicting Blast Furnace Process

NASA Astrophysics Data System (ADS)

Fu, Dong; Tang, Guangwu; Zhao, Yongfu; D'Alessio, John; Zhou, Chenn Q.

2018-06-01

A novel modeling strategy is presented for simulating the blast furnace iron making process. Such physical and chemical phenomena are taking place across a wide range of length and time scales, and three models are developed to simulate different regions of the blast furnace, i.e., the tuyere model, the raceway model and the shaft model. This paper focuses on the integration of the three models to predict the entire blast furnace process. Mapping output and input between models and an iterative scheme are developed to establish communications between models. The effects of tuyere operation and burden distribution on blast furnace fuel efficiency are investigated numerically. The integration of different models provides a way to realistically simulate the blast furnace by improving the modeling resolution on local phenomena and minimizing the model assumptions.

Minimization of Blast furnace Fuel Rate by Optimizing Burden and Gas Distribution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Chenn Zhou

2012-08-15

The goal of the research is to improve the competitive edge of steel mills by using the advanced CFD technology to optimize the gas and burden distributions inside a blast furnace for achieving the best gas utilization. A state-of-the-art 3-D CFD model has been developed for simulating the gas distribution inside a blast furnace at given burden conditions, burden distribution and blast parameters. The comprehensive 3-D CFD model has been validated by plant measurement data from an actual blast furnace. Validation of the sub-models is also achieved. The user friendly software package named Blast Furnace Shaft Simulator (BFSS) has beenmore » developed to simulate the blast furnace shaft process. The research has significant benefits to the steel industry with high productivity, low energy consumption, and improved environment.« less

Difficulties associated with predicting forage intake by grazing beef cows

USDA-ARS?s Scientific Manuscript database

The current National Research Council (NRC) model is based on a single equation that relates dry matter intake (DMI) to metabolic size and net energy density of the diet offered and was a significant improvement over previous models. However, observed DMI by grazing animals can be conceptualized by...

First report of DMI insensitive Cercospora beticola on sugar beet in Ontario, Canada

USDA-ARS?s Scientific Manuscript database

Cercospora leaf spot (CLS), caused by the fungal pathogen Cercospora beticola, is an economically important foliar disease of sugar beet in Ontario, Canada and worldwide. Fungicides are an important tool in the control of CLS. The first demethylation inhibitor (DMI) fungicide for sugar beet was regi...

Dependence of interfacial Dzyaloshinskii-Moriya interaction and perpendicular magnetic anisotropy on the thickness of the heavy-metal layer

NASA Astrophysics Data System (ADS)

Kim, Nam-Hui; Han, Dong-Soo; Jung, Jinyong; Park, Kwonjin; Swagten, Henk J. M.; Kim, June-Seo; You, Chun-Yeol

2017-10-01

The interfacial Dzyaloshinskii-Moriya interaction (iDMI) and the interfacial perpendicular magnetic anisotropy (iPMA) between a heavy metal and ferromagnet are investigated by employing Brillouin light scattering. With increasing thickness of the heavy-metal (Pt) layer, the iDMI and iPMA energy densities are rapidly enhanced and they saturate for a Pt thickness of 2.4 nm. Since these two individual magnetic properties show the same Pt thickness dependence, this is evidence that the iDMI and iPMA at the interface between the heavy metal and ferromagnet, the physical origin of these phenomena, are effectively enhanced upon increasing the thickness of the heavy-metal layer.

WAIS-III FSIQ and GAI in ability-memory discrepancy analysis.

PubMed

Glass, Laura A; Bartels, Jared M; Ryan, Joseph J

2009-01-01

The present investigation compares WAIS-III FSIQ-WMS-III with GAI-WMS-III discrepancies in 135 male inpatients with suspected memory impairment. Full Scale IQ and GAI scores were highly correlated, r= .96, with mean values of 92.10 and 93.59, respectively. Additional analyses with the ability composites compared to each WMS-III index (IMI, GMI, and DMI), the GAI consistently produced larger difference scores than did the FSIQ; however, effect sizes were relatively small (ES= .12). Lastly, case-by-case analyses demonstrated concordance rates of 86% for the FSIQ-IMI and GAI-IMI comparisons, 85% for the FSIQ-GMI and GAI-GMI, and 82% for the FSIQ-DMI and GAI-DMI.

Controllable magnetic thermal rectification in a SMM dimmer with the Dzyaloshinskii-Moriya interaction

NASA Astrophysics Data System (ADS)

Xu, Ai-Hua; Liu, Juan; Luo, Bo

2016-10-01

Using the quantum master equation, we studied the thermally driven magnonic spin current in a single-molecule magnet (SMM) dimer with the Dzyaloshinskii-Moriya interaction (DMI). Due to the asymmetric DMI, one can observe the thermal rectifying effect in the case of the spatial symmetry coupling with the thermal reservoirs. The properties of the thermal rectification can be controlled by tuning the angle and intensity of the magnetic field. Specially, when the DM vector and magnetic field point at the specific angles, the thermal rectifying effect disappears. And this phenomenon does not depend on the intensities of DMI and magnetic field, the temperature bias and the magnetic anisotropies of the SMM.

RNA-Sequencing of Cercospora beticola DMI-sensitive and -resistant isolates after treatment with tetraconazole identifies common and contrasting pathway induction

USDA-ARS?s Scientific Manuscript database

Cercospora beticola causes Cercospora leaf spot of sugarbeet. Cercospora leaf spot management measures often include application of the sterol demethylation inhibitor (DMI) class of fungicides. The reliance on DMIs and the consequent selection pressures imposed by their widespread use has led to th...

Effect of interfacial intermixing on the Dzyaloshinskii-Moriya interaction in Pt/Co/Pt

NASA Astrophysics Data System (ADS)

Wells, Adam W. J.; Shepley, Philippa M.; Marrows, Christopher H.; Moore, Thomas A.

2017-02-01

We study the effect of sputter-deposition conditions, namely, substrate temperature and chamber base pressure, upon the interface quality of epitaxial Pt/Co/Pt thin films with perpendicular magnetic anisotropy. Here we define interface quality to be the inverse of the sum in quadrature of roughness and intermixing. We find that samples with the top Co/Pt layers grown at 250 ∘C exhibit a local maximum in roughness intermixing and that the interface quality is better for lower or higher deposition temperatures, up to 400 ∘C,above which the interface quality degrades. Imaging the expansion of magnetic domains in an in-plane field using wide-field Kerr microscopy, we determine the interfacial Dzyaloshinskii-Moriya interaction (DMI) in films in the deposition temperature range 100 ∘C to 300 ∘C . We find that the net DMI increases as the difference between top and bottom Co interface quality increases. Furthermore, for sufficiently low base pressures, the net DMI increases linearly with the deposition temperature, indicating that fine-tuning of the DMI may be achieved via the deposition conditions.

Dry matter yields and quality of forages derived from grass species and organic production methods (year 111).

PubMed

Pholsen, S; Rodchum, P; Higgs, D E B

2014-07-01

This third year work was carried on at Khon Kaen University during the 2008-2009 to investigate dry matter yields of grass, grass plus legumes, grown on Korat soil series (Oxic Paleustults). The experiment consisted of twelve-treatment combinations of a 3x4 factorial arranged in a Randomized Complete Block Design (RCBD) with four replications. The results showed that Dry Matter Yields (DMY) of Ruzi and Guinea grass were similar with mean values of 6,585 and 6,130 kg ha(-1) whilst Napier gave the lowest (884 kg ha(-1)). With grass plus legume, grass species and production methods gave highly significant dry matter yields where Guinea and Ruzi gave dry matter yields of 7,165 and 7,181 kg ha(-1), respectively and Napier was the least (2,790 kg ha(-1)). The production methods with the use of cattle manure gave the highest DMY (grass alone) of 10,267 kg ha(-1) followed by Wynn and Verano with values of 6,064 and 3,623 kg ha(-1), respectively. Guinea plus cattle manure gave the highest DMY of 14,599 kg ha(-1) whilst Ruzi gave 12,977 kg ha(-1). Guinea plus Wynn gave DMY of 7,082 kg ha(-1). Ruzi plus Verano gave DMY of 6,501 kg ha(-1). Forage qualities of crude protein were highest with those grown with grass plus legumes. Some prospects in improving production were discussed.

Effects of grain, fructose, and histidine on ruminal pH and fermentation products during an induced subacute acidosis protocol.

PubMed

Golder, H M; Celi, P; Rabiee, A R; Heuer, C; Bramley, E; Miller, D W; King, R; Lean, I J

2012-04-01

The effects of grain, fructose, and histidine on ruminal pH and fermentation products were studied in dairy cattle during an induced subacute acidosis protocol. Thirty Holstein heifers were randomly allocated to 5 treatment groups: (1) control (no grain); (2) grain [fed at a crushed triticale dry matter intake (DMI) of 1.2% of body weight (BW)]; (3) grain (0.8% of BW DMI)+fructose (0.4% of BW DMI); (4) grain (1.2% of BW DMI)+histidine (6 g/head); and (5) grain (0.8% of BW DMI)+fructose (0.4% of BW DMI)+histidine (6 g/head) in a partial factorial arrangement. Heifers were fed 1 kg of grain daily with ad libitum access to ryegrass silage and alfalfa hay for 10 d. Feed was withheld for 14 h before challenge day, on which heifers were fed 200 g of alfalfa hay and then the treatment diets immediately thereafter. Rumen samples were collected 5 min after diet ingestion, 60 min later, and at 3 subsequent 50-min intervals. Grain decreased ruminal pH and increased ammonia, total volatile fatty acid (VFA), acetate, butyrate, propionate, and valerate concentrations compared with controls. The addition of grain had no effect on ruminal D- and L-lactate concentrations. Fructose markedly decreased ruminal pH and markedly increased D- and L-lactate concentrations. Fructose increased total VFA and butyrate and decreased valerate concentrations. Although histidine did not have a marked effect on ruminal fermentation, increased concentrations of histamine were observed following feeding. This study demonstrates that the substitution of some grain for fructose can lower ruminal pH and increase VFA and lactate concentrations, warranting further investigation into the role of sugars on the risk of acidosis in dairy cattle. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

TECHNOLOGY EVALUATION REPORT: RETECH'S PLASMA CENTRIFUGAL FURNACE - VOLUME I

EPA Science Inventory

A demonstration of the Retech, Inc. Plasma Centrifugal Furnace (PCF) was conducted under the Superfund Innovative Technology Evaluation (SITE) Program at the Department of Energy's (DOE's) Component Development and Integration Facility in Butte, Montana. The furnace uses heat gen...

Ultra-high vacuum compatible preparation chain for intermetallic compounds

NASA Astrophysics Data System (ADS)

Bauer, A.; Benka, G.; Regnat, A.; Franz, C.; Pfleiderer, C.

2016-11-01

We report the development of a versatile material preparation chain for intermetallic compounds, which focuses on the realization of a high-purity growth environment. The preparation chain comprises an argon glovebox, an inductively heated horizontal cold boat furnace, an arc melting furnace, an inductively heated rod casting furnace, an optically heated floating-zone furnace, a resistively heated annealing furnace, and an inductively heated annealing furnace. The cold boat furnace and the arc melting furnace may be loaded from the glovebox by means of a load-lock permitting to synthesize compounds starting with air-sensitive elements while handling the constituents exclusively in an inert gas atmosphere. All furnaces are all-metal sealed, bakeable, and may be pumped to ultra-high vacuum. We find that the latter represents an important prerequisite for handling compounds with high vapor pressure under high-purity argon atmosphere. We illustrate the operational aspects of the preparation chain in terms of the single-crystal growth of the heavy-fermion compound CeNi2Ge2.

Studies on the Processing Methods for Extraterrestrial Materials

NASA Technical Reports Server (NTRS)

Grimley, R. T.; Lipschutz, M. E.

1984-01-01

The literature was surveyed for high temperature mass spectrometric research on single oxides, complex oxides, and minerals in an effort to develop a means of separating elements and compounds from lunar and other extraterrestrial materials. A data acquisition system for determining vaporization rates as a function of time and temperature and software for the IEEE-488 Apple-ORTEC interface are discussed. Experimental design information from a 1000 C furnace were used with heat transfer calculations to develop the basic design for a 1600 C furnace. A controller was built for the higher temperature furnace and drawings are being made for the furnace.

Effects of grass silage quality and level of feed intake on enteric methane production in lactating dairy cows.

PubMed

Warner, D; Bannink, A; Hatew, B; van Laar, H; Dijkstra, J

2017-08-01

The objective of this study was to determine the effect of level of feed intake and quality of ryegrass silage as well as their interaction on enteric methane (CH) emission from dairy cows. In a randomized block design, 56 lactating dairy cows received a diet of grass silage, corn silage, and a compound feed meal (70:10:20 on DM basis). Treatments consisted of 4 grass silage qualities prepared from grass harvested from leafy through late heading stage, and offered to dairy cows at 96 ± 2.4 (mean ± SEM) days in milk (namely, high intake) and 217 ± 2.4 d in milk (namely, low intake). Grass silage CP content varied between 124 and 286 g/kg of DM, and NDF content between 365 and 546 g/kg of DM. After 12 d of adaptation, enteric CH production of cows was measured in open-circuit climate-controlled respiration chambers for 5 d. No interaction between DMI and grass quality on CH emission, or on milk production, diet digestibility, and energy, and N retention was found ( ≥ 0.17). Cows had a greater DMI (16.6 vs. 15.5 kg/d; SEM 0.46) and greater fat- and protein-corrected milk (FPCM) yield (29.9 vs. 25.4 kg/d; SEM 1.24) at high than low intake (both ≤ 0.001). Apparent total-tract nutrient digestibility was not affected ( ≥ 0.08) by DMI level. Total enteric CH production (346 ± 10.9 g/d) was not affected ( = 0.15) by DMI level. A small, significant ( = 0.025) decrease at high compared with low intake occurred for CH yield (21.8 ± 0.59 g/kg of DMI; -4%). Methane emission intensity (12.8 ± 0.56 g/kg of FPCM; -12%) was considerably smaller ( ≤ 0.001) at high intake as a result of greater milk yields realized in early lactation. As grass quality decreased from leafy through late heading stage, FPCM yield and apparent total-tract OM digestibility declined (-12%; ≤ 0.015), whereas total CH production (+13%), CH yield (+21%), and CH emission intensity (+28%) increased ( ≤ 0.001). Our results suggest that improving grass silage quality by cutting grass at an earlier stage considerably reduces enteric CH emissions from dairy cows, independent of DMI. In contrast, losses of N in manure increased for the earlier cut grass silage treatments. The small increase in DMI at high intake was associated with a small to moderate reduction in CH emission per unit of DMI and GE intake. This study confirmed that enteric CH emissions from dairy cows at distinct levels of feed intake depend on the nutritive value and chemical composition of the grass silage.

Genomewide association study of methane emissions in Angus beef cattle with validation in dairy cattle.

PubMed

Manzanilla-Pech, C I V; De Haas, Y; Hayes, B J; Veerkamp, R F; Khansefid, M; Donoghue, K A; Arthur, P F; Pryce, J E

2016-10-01

Methane (CH) is a product of enteric fermentation in ruminants, and it represents around 17% of global CH emissions. There has been substantial effort from the livestock scientific community toward tools that can help reduce this percentage. One approach is to select for lower emitting animals. To achieve this, accurate genetic parameters and identification of the genomic basis of CH traits are required. Therefore, the objectives of this study were 1) to perform a genomewide association study to identify SNP associated with several CH traits in Angus beef cattle (1,020 animals) and validate them in a lactating Holstein population (population 1 [POP1]; 205 animals); 2) to validate significant SNP for DMI and weight at test (WT) from a second Holstein population, from a previous study (population 2 [POP2]; 903 animals), in an Angus population; and 3) to evaluate 2 different residual CH traits and determine if the genes associated with CH also control residual CH traits. Phenotypes calculated for the genotyped Angus population included CH production (MeP), CH yield (MeY), CH intensity (MI), DMI, and WT. The Holstein population (POP1) was multiparous, with phenotypes on CH traits (MeP, MeY, and MI) plus genotypes. Additionally, 2 CH traits, residual genetic CH (RGM) and residual phenotypic CH (RPM), were calculated by adjusting MeP for DMI and WT. Estimated heritabilities in the Angus population were 0.30, 0.19, and 0.15 for MeP, RGM, and RPM, respectively, and genetic correlations of MeP with DMI and WT were 0.83 and 0.80, respectively. Estimated heritabilities in Holstein POP1 were 0.23, 0.30, and 0.42 for MeP, MeY, and MI, respectively. Strong associations with MeP were found on chromosomes 4, 12, 14, 20, and 30 at < 0.001, and those chromosomes also had significant SNP for DMI in Holstein POP1. In the Angus population, the number of significant SNP for MeP at < 0.005 was 3,304, and approximately 630 of those SNP also were important for DMI and WT. When a set (approximately 3,300) of significant SNP for DMI and WT in the Angus population was used to estimate genetic parameters for MeP and MeY in Holstein POP1, the genetic variance and, consequently, the heritability slightly increased, meaning that most of the genetic variation is largely captured by these SNP. Residual traits could be a good option to include in the breeding goal, as this would facilitate selection for lower emitting animals without compromising DMI and WT.

Nutrient demand interacts with grass maturity to affect milk fat concentration and digestion responses in dairy cows.

PubMed

Kammes, K L; Allen, M S

2012-09-01

Effects of grass maturity on dry matter intake (DMI), milk production, ruminal fermentation and pool sizes, digestion and passage kinetics, and chewing activity and the relationship of these effects with preliminary DMI (pDMI) were evaluated using 13 ruminally and duodenally cannulated Holstein cows in a crossover design with a 14-d preliminary period and two 18-d treatment periods. During the preliminary period, pDMI of individual cows ranged from 23.5 to 28.2 kg/d (mean=26.1 kg/d) and 3.5% fat-corrected milk (FCM) yield ranged from 30.8 to 57.2 kg/d (mean=43.7 kg/d). Experimental treatments were diets containing orchardgrass silage harvested either (1) early-cut, less mature (EC) or (2) late-cut, more mature (LC) as the sole forage. Early- and late-cut orchardgrass contained 44.9 and 54.4% neutral detergent fiber (NDF) and 20.1 and 15.3% crude protein, respectively. Forage:concentrate ratio was 58:42 and 46:54 for EC and LC, respectively; both diets contained approximately 25% forage NDF and 30% total NDF. Preliminary DMI, an index of nutrient demand, was determined during the last 4d of the preliminary period when cows were fed a common diet and used as a covariate. Main effects of grass maturity and their interaction with pDMI were tested by ANOVA. The EC diet decreased milk yield and increased milk fat concentration compared with the LC diet. Grass maturity and its interaction with pDMI did not affect FCM yield, DMI, rumen pH, or microbial efficiency. The EC diet increased rates of ruminal digestion of potentially digestible NDF and passage of indigestible NDF (iNDF) compared with the LC diet. The lower concentration and faster passage rate of iNDF for EC resulted in lower rumen pools of iNDF, total NDF, organic matter, and dry matter for EC than LC. Ruminal passage rates of potentially digestible NDF and starch were related to level of intake (quadratic and linear interactions, respectively) and subsequently affected ruminal digestibility of these nutrients. The EC diet decreased eating, ruminating, and total chewing time per unit of forage NDF intake compared with the LC diet. When grass silage was the only source of forage in the diet, cows supplemented with additional concentrate to account for decreasing protein and increasing fiber concentrations associated with more mature grass had similar feed intake and produced similar FCM yields as cows fed less mature grass. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The addition of cottonseed hulls to the starter and supplementation of live yeast or mannanoligosaccharide in the milk for young calves.

PubMed

Hill, S R; Hopkins, B A; Davidson, S; Bolt, S M; Diaz, D E; Brownie, C; Brown, T; Huntington, G B; Whitlow, L W

2009-02-01

The objectives of this study were to investigate the effects of the addition of cottonseed hulls (CSH) to the starter and the supplementation of live yeast product (YST) or mannanoligosaccharide product (MOS) to milk, on growth, intake, rumen development, and health parameters in young calves. Holstein (n = 116) and Jersey (n = 46) bull (n = 74) and heifer (n = 88) calves were assigned randomly within sex at birth to treatments. All calves were fed 3.8 L of colostrum daily for the first 2 d. Holstein calves were fed 3.8 L of whole milk, and Jersey calves were fed 2.8 L of whole milk through weaning at 42 d. Calves continued on trial through 63 d. Six treatments were arranged as a 2 x 3 factorial. Calves received either a corn-soybean meal-based starter (21% crude protein and 6% acid detergent fiber; -CSH) or a blend of 85% corn-soybean meal-based starter and 15% CSH (18% crude protein and 14% acid detergent fiber; +CSH) ad libitum. In addition, calves received whole milk with either no supplement (NONE) or supplemented with 3 g/d of mannanoligosaccharide product (MOS) or 4 g/d of live yeast product (YST) through weaning at 42 d. Twelve Holstein steers [n = 6 (per starter type); n = 4 (per supplement type)] were euthanized for collection and examination of rumen tissue samples. Dry matter intake (DMI) was greater for Holstein calves fed +CSH (0.90 kg/d) than -CSH (0.76 kg/d). Final body weight at 63 d of Holstein calves fed +CSH (75.8 kg) was greater than that of those fed -CSH (71.0 kg). Average daily gain (ADG) was greater for Holstein calves fed +CSH (0.58 kg/d) than -CSH (0.52 kg/d). However, Holstein calves fed -CSH had a greater feed efficiency (FE; 0.71 kg of ADG/kg of DMI) than those fed +CSH (0.65 kg of ADG/kg of DMI). Also, Holstein calves fed +CSH had narrower rumen papillae (0.32 mm) compared with those fed -CSH (0.41 mm). There were no significant effects of CSH on DMI, ADG, or FE in Jersey calves. There were no significant effects of YST or MOS on DMI, ADG, FE, or rumen papillae measures in Holstein calves. Jersey calves fed YST or MOS had greater final body weight at 63 d (51.2 kg and 51.0 kg, respectively) than calves fed NONE (47.5 kg). However, there were no significant effects of YST or MOS on DMI, ADG, or FE in Jersey calves.

Quality assurance for online adapted treatment plans: Benchmarking and delivery monitoring simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Taoran, E-mail: taoran.li.duke@gmail.com; Wu, Qiuwen; Yang, Yun

Purpose: An important challenge facing online adaptive radiation therapy is the development of feasible and efficient quality assurance (QA). This project aimed to validate the deliverability of online adapted plans and develop a proof-of-concept online delivery monitoring system for online adaptive radiation therapy QA. Methods: The first part of this project benchmarked automatically online adapted prostate treatment plans using traditional portal dosimetry IMRT QA. The portal dosimetry QA results of online adapted plans were compared to original (unadapted) plans as well as randomly selected prostate IMRT plans from our clinic. In the second part, an online delivery monitoring system wasmore » designed and validated via a simulated treatment with intentional multileaf collimator (MLC) errors. This system was based on inputs from the dynamic machine information (DMI), which continuously reports actual MLC positions and machine monitor units (MUs) at intervals of 50 ms or less during delivery. Based on the DMI, the system performed two levels of monitoring/verification during the delivery: (1) dynamic monitoring of cumulative fluence errors resulting from leaf position deviations and visualization using fluence error maps (FEMs); and (2) verification of MLC positions against the treatment plan for potential errors in MLC motion and data transfer at each control point. Validation of the online delivery monitoring system was performed by introducing intentional systematic MLC errors (ranging from 0.5 to 2 mm) to the DMI files for both leaf banks. These DMI files were analyzed by the proposed system to evaluate the system’s performance in quantifying errors and revealing the source of errors, as well as to understand patterns in the FEMs. In addition, FEMs from 210 actual prostate IMRT beams were analyzed using the proposed system to further validate its ability to catch and identify errors, as well as establish error magnitude baselines for prostate IMRT delivery. Results: Online adapted plans were found to have similar delivery accuracy in comparison to clinical IMRT plans when validated with portal dosimetry IMRT QA. FEMs for the simulated deliveries with intentional MLC errors exhibited distinct patterns for different MLC error magnitudes and directions, indicating that the proposed delivery monitoring system is highly specific in detecting the source of errors. Implementing the proposed QA system for online adapted plans revealed excellent delivery accuracy: over 99% of leaf position differences were within 0.5 mm, and >99% of pixels in the FEMs had fluence errors within 0.5 MU. Patterns present in the FEMs and MLC control point analysis for actual patient cases agreed with the error pattern analysis results, further validating the system’s ability to reveal and differentiate MLC deviations. Calculation of the fluence map based on the DMI was performed within 2 ms after receiving each DMI input. Conclusions: The proposed online delivery monitoring system requires minimal additional resources and time commitment to the current clinical workflow while still maintaining high sensitivity to leaf position errors and specificity to error types. The presented online delivery monitoring system therefore represents a promising QA system candidate for online adaptive radiation therapy.« less

Quality assurance for online adapted treatment plans: benchmarking and delivery monitoring simulation.

PubMed

Li, Taoran; Wu, Qiuwen; Yang, Yun; Rodrigues, Anna; Yin, Fang-Fang; Jackie Wu, Q

2015-01-01

An important challenge facing online adaptive radiation therapy is the development of feasible and efficient quality assurance (QA). This project aimed to validate the deliverability of online adapted plans and develop a proof-of-concept online delivery monitoring system for online adaptive radiation therapy QA. The first part of this project benchmarked automatically online adapted prostate treatment plans using traditional portal dosimetry IMRT QA. The portal dosimetry QA results of online adapted plans were compared to original (unadapted) plans as well as randomly selected prostate IMRT plans from our clinic. In the second part, an online delivery monitoring system was designed and validated via a simulated treatment with intentional multileaf collimator (MLC) errors. This system was based on inputs from the dynamic machine information (DMI), which continuously reports actual MLC positions and machine monitor units (MUs) at intervals of 50 ms or less during delivery. Based on the DMI, the system performed two levels of monitoring/verification during the delivery: (1) dynamic monitoring of cumulative fluence errors resulting from leaf position deviations and visualization using fluence error maps (FEMs); and (2) verification of MLC positions against the treatment plan for potential errors in MLC motion and data transfer at each control point. Validation of the online delivery monitoring system was performed by introducing intentional systematic MLC errors (ranging from 0.5 to 2 mm) to the DMI files for both leaf banks. These DMI files were analyzed by the proposed system to evaluate the system's performance in quantifying errors and revealing the source of errors, as well as to understand patterns in the FEMs. In addition, FEMs from 210 actual prostate IMRT beams were analyzed using the proposed system to further validate its ability to catch and identify errors, as well as establish error magnitude baselines for prostate IMRT delivery. Online adapted plans were found to have similar delivery accuracy in comparison to clinical IMRT plans when validated with portal dosimetry IMRT QA. FEMs for the simulated deliveries with intentional MLC errors exhibited distinct patterns for different MLC error magnitudes and directions, indicating that the proposed delivery monitoring system is highly specific in detecting the source of errors. Implementing the proposed QA system for online adapted plans revealed excellent delivery accuracy: over 99% of leaf position differences were within 0.5 mm, and >99% of pixels in the FEMs had fluence errors within 0.5 MU. Patterns present in the FEMs and MLC control point analysis for actual patient cases agreed with the error pattern analysis results, further validating the system's ability to reveal and differentiate MLC deviations. Calculation of the fluence map based on the DMI was performed within 2 ms after receiving each DMI input. The proposed online delivery monitoring system requires minimal additional resources and time commitment to the current clinical workflow while still maintaining high sensitivity to leaf position errors and specificity to error types. The presented online delivery monitoring system therefore represents a promising QA system candidate for online adaptive radiation therapy.

Paired Straight Hearth Furnace - Transformational Ironmaking Process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Wei-Kao; Debski, Paul

2014-11-19

The U. S. steel industry has reduced its energy intensity per ton of steel shipped by 33% since 1990. However, further significant gains in energy efficiency will require the development of new, transformational iron and steelmaking processes. The Paired Straight Hearth Furnace (PSH) process is an emerging alternative high productivity, direct reduced iron (DRI) technology that may achieve very low fuel rates and has the potential to replace blast furnace ironmaking. The PSH furnace can operate independently or may be coupled with other melting technologies to produce liquid hot metal that is both similar to blast furnace iron and suitablemore » as a feedstock for basic oxygen steelmaking furnaces. The PSH process uses non-metallurgical coal as a reductant to convert iron oxides such as iron ore and steelmaking by-product oxides to DRI pellets. In this process, a multi-layer, nominally 120mm tall bed of composite “green balls” made from oxide, coal and binder is built up and contained within a moving refractory hearth. The pellet bed absorbs radiant heat energy during exposure to the high temperature interior refractory surfaces of the PSH while generating a strongly reducing gas atmosphere in the bed that yields a highly metalized DRI product. The PSH concept has been well tested in static hearth experiments. A moving bed design is being developed. The process developers believe that if successful, the PSH process has the potential to replace blast furnaces and coke ovens at a fraction of the operating and capital cost while using about 30% less energy relative to current blast furnace technology. DRI output could also feed electric arc furnaces (EAFs) by displacing a portion of the scrap charge.« less

Association of circulating active and total ghrelin concentrations with dry matter intake, growth, and carcass characteristics of finishing beef cattle

USDA-ARS?s Scientific Manuscript database

Ghrelin is a gut peptide that when acylated is thought to stimulate appetite. Circulating ghrelin concentrations could potentially be used as a predictor of DMI in cattle. The objective of this experiment was to determine the association of circulating ghrelin concentrations with DMI and other produ...

Multipurpose electric furnace system. [for use in Apollo-Soyuz Test Program

NASA Technical Reports Server (NTRS)

Mazelsky, R.; Duncan, C. S.; Seidensticker, R. G.; Johnson, R. A.; Mchugh, J. P.; Foust, H. C.; Piotrowski, P. A.

1974-01-01

A multipurpose electric furnace system of advanced design for space applications was developed and tested. This system is intended for use in the Apollo-Soyuz Test Program. It consists of the furnace, control package and a helium package for rapid cooldown.

Design and Development of Tilting Rotary Furnace

NASA Astrophysics Data System (ADS)

Sai Varun, V.; Tejesh, P.; Prashanth, B. N.

2018-02-01

Casting is the best and effective technique used for manufacturing products. The important accessory for casting is furnace. Furnace is used to melt the metal. A perfect furnace is one that reduces the wastage of material, reduces the cost of manufacturing and there by reduces the cost of production. Of all the present day furnaces there may be wastage of material, and the chances of increasing the time of manufacturing as the is continuous need of tilting of the furnace for every mould and then changing the moulds. Considering these aspects, a simple and least expensive tilting rotary furnace is designed and developed. The Tilting and Rotary Furnace consists of mainly melting chamber and the base. The metal enters the melting chamber through the input door that is provided on the top of the melting chamber. Inside the melting chamber there is a graphite furnace. The metal is melted in the graphite crucible. An insulation of ceramic fibre cloth is provided inside the furnace. The metal is melted using Propane gas. The propane gas is easily available and economic. The gas is burned using a pilot burner. The pilot burner is more efficient that other burners. The pilot burner is lit with a push button igniter. The pilot burner is located at the bottom of the combustion chamber. This enables the uniform heating of the metal inside the crucible. The temperature inside the melting chamber is noted using a temperature sensor. The gas input is cut-off if the temperature is exceeding a specific temperature. After the melting of the metal is done the furnace is tilted and after the mould is filled it is rotated. The external gears are used to controlling the tilting. The results of studies carried out for the design & development of low cost, simple furnace that can be mounted anywhere on the shop floor and this can be very much useful for the education purposes and small scale manufacturing. The furnace can be rotated in 360 degrees and can help in reducing the time taken in manufacturing. The furnace is provided with a rotation motion to the base which helps in providing a uniform distribution of molten metal to various moulds and can be used to fill a number of moulds with minimal wastage of the molten material. Due to the tilting action provided to the combustion chamber, the flow of metal can be controlled easily during pouring of molten metal into the moulds.

Relationship among performance, carcass, and feed efficiency characteristics, and their ability to predict economic value in the feedlot.

PubMed

Retallick, K M; Faulkner, D B; Rodriguez-Zas, S L; Nkrumah, J D; Shike, D W

2013-12-01

A 4-yr study was conducted using 736 steers of known Angus, Simmental, or Simmental × Angus genetics to determine performance, carcass, and feed efficiency factors that explained variation in economic performance. Steers were pen fed and individual DMI was recorded using a GrowSafe automated feeding system (GrowSafe Systems Ltd., Airdrie, Alberta, Canada). Steers consumed a similar diet and received similar management each year. The objectives of this study were to: 1) determine current economic value of feed efficiency and 2) identify performance, carcass, and feed efficiency characteristics that predict: carcass value, profit, cost of gain, and feed costs. Economic data used were from 2011 values. Feed efficiency values investigated were: feed conversion ratio (FCR; feed to gain), residual feed intake (RFI), residual BW gain (RG), and residual intake and BW gain (RIG). Dependent variables were carcass value ($/steer), profit ($/steer), feed costs ($/steer • d(-1)), and cost of gain ($/kg). Independent variables were year, DMI, ADG, HCW, LM area, marbling, yield grade, dam breed, and sire breed. A 10% improvement in RG (P < 0.05) yielded the lowest cost of gain at $0.09/kg and highest carcass value at $17.92/steer. Carcass value increased (P < 0.05) as feed efficiency improved for FCR, RG, and RIG. Profit increased with a 10% improvement in feed efficiency (P < 0.05) with FCR at $34.65/steer, RG at $31.21/steer, RIG at $21.66/steer, and RFI at $11.47/steer. The carcass value prediction model explained 96% of the variation among carcasses and included HCW, marbling score, and yield grade. Average daily gain, marbling score, yield grade, DMI, HCW, and year born constituted 81% of the variation for prediction of profit. Eighty-five percent of the variation in cost of gain was explained by ADG, DMI, HCW, and year. Prediction equations were developed that excluded ADG and DMI, and included feed efficiency values. Using these equations, cost of gain was explained primarily by FCR (R(2) = 0.71). Seventy-three percent of profitability was explained, with 55% being accounted for by RG and marbling. These prediction equations represent the relative importance of factors contributing to economic success in feedlot cattle based on current prices.

Calculation and research of electrical characteristics of induction crucible furnaces with unmagnetized conductive crucible

NASA Astrophysics Data System (ADS)

Fedin, M. A.; Kuvaldin, A. B.; Kuleshov, A. O.; Zhmurko, I. Y.; Akhmetyanov, S. V.

2018-01-01

Calculation methods for induction crucible furnaces with a conductive crucible have been reviewed and compared. The calculation method of electrical and energy characteristics of furnaces with a conductive crucible has been developed and the example of the calculation is shown below. The calculation results are compared with experimental data. Dependences of electrical and power characteristics of the furnace on frequency, inductor current, geometric dimensions and temperature have been obtained.

Chronic desipramine treatment alters tyrosine hydroxylase but not norepinephrine transporter immunoreactivity in norepinephrine axons in the rat prefrontal cortex

PubMed Central

Erickson, Susan L.; Gandhi, Anjalika R.; Asafu-Adjei, Josephine K.; Sampson, Allan R.; Miner, LeeAnn; Blakely, Randy D.; Sesack, Susan R.

2011-01-01

Pharmacological blockade of norepinephrine (NE) reuptake is clinically effective in treating several mental disorders. Drugs that bind to the NE transporter (NET) alter both protein levels and activity of NET and also the catecholamine synthetic enzyme tyrosine hydroxylase (TH). We examined the rat prefrontal cortex (PFC) by electron microscopy to determine whether the density and subcellular distribution of immunolabeling for NET and colocalization of NET with TH within individual NE axons were altered by chronic treatment with the selective NE uptake inhibitor desipramine (DMI). Following DMI treatment (21 days, 15 mg/kg/day), NET-immunoreactive (-ir) axons were significantly less likely to colocalize TH. This finding is consistent with reports of reduced TH levels and activity in the locus coeruleus after chronic DMI and indicates a reduction of NE synthetic capacity in the PFC. Measures of NET expression and membrane localization, including the number of NET-ir profiles per tissue area sampled, the number of gold particles per NET-ir profile area, and the proportion of gold particles associated with the plasma membrane, were similar in DMI and vehicle treated rats. These findings were verified using two different antibodies directed against distinct epitopes of the NET protein. The results suggest that chronic DMI treatment does not reduce NET expression within individual NE axons in vivo or induce an overall translocation of NET protein away from the plasma membrane in the PFC as measured by ultrastructural immunogold labeling. Our findings encourage consideration of possible postranslational mechanisms for regulating NET activity in antidepressant-induced modulation of NE clearance. PMID:21208501

Glycemic Status Affects the Subgingival Microbiome of Diabetic Patients.

PubMed

Longo, Priscila Larcher; Dabdoub, Shareef; Kumar, Purnima; Artese, Hilana Paula Carillo; Dib, Sergio Atala; Romito, Giuseppe Alexandre; Mayer, Marcia Pinto Alves

2018-05-09

Periodontitis is correlated with type 2 diabetes mellitus (T2DM), but little is known about glycemic status effect on subgingival microbiota associated with periodontitis. This study evaluated if periodontal microbiome of T2DM patients is affected by glycemic status. 21 T2DM non-smoking patients with chronic periodontitis and body mass index ≤40kg/m 2 were allocated into two groups according to systemic glycemic status: inadequate (DMI- HbA1c≥8%) and adequate (DMA- HbA1c<7.8%). Subgingival biofilm was collected from sites with moderate (PD=4-6mm) and severe disease (PD≥7mm) in two quadrants. The V5-V6 hypervariable region of the 16SrRNA was sequenced using the GS-FLX-454Titanium platform. Sequences were compared to HOMD database using QIIME and PhyloToAST pipelines. Statistical comparisons were made using 2-sample t-tests. DMA microbiome presented higher diversity than DMI. Inadequate glycemic control favored fermenting species, especially those associated with propionate/succinate production, whereas those forming butyrate/pyruvate were decreased in DMI. Higher abundances of anginosus group and Streptococcus agalactiae in DMI may indicate that subgingival sites can be reservoir of potentially invasive pathogens. Altered subgingival microbiome in DMI may represent an additional challenge in the periodontal treatment of these patients and in the prevention of more invasive infections. Glycemic status in T2DM patients seems to modulate subgingival biofilm composition. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Antidepressant suppression of non-REM sleep spindles and REM sleep impairs hippocampus-dependent learning while augmenting striatum-dependent learning.

PubMed

Watts, Alain; Gritton, Howard J; Sweigart, Jamie; Poe, Gina R

2012-09-26

Rapid eye movement (REM) sleep enhances hippocampus-dependent associative memory, but REM deprivation has little impact on striatum-dependent procedural learning. Antidepressant medications are known to inhibit REM sleep, but it is not well understood if antidepressant treatments impact learning and memory. We explored antidepressant REM suppression effects on learning by training animals daily on a spatial task under familiar and novel conditions, followed by training on a procedural memory task. Daily treatment with the antidepressant and norepinephrine reuptake inhibitor desipramine (DMI) strongly suppressed REM sleep in rats for several hours, as has been described in humans. We also found that DMI treatment reduced the spindle-rich transition-to-REM sleep state (TR), which has not been previously reported. DMI REM suppression gradually weakened performance on a once familiar hippocampus-dependent maze (reconsolidation error). DMI also impaired learning of the novel maze (consolidation error). Unexpectedly, learning of novel reward positions and memory of familiar positions were equally and oppositely correlated with amounts of TR sleep. Conversely, DMI treatment enhanced performance on a separate striatum-dependent, procedural T-maze task that was positively correlated with the amounts of slow-wave sleep (SWS). Our results suggest that learning strategy switches in patients taking REM sleep-suppressing antidepressants might serve to offset sleep-dependent hippocampal impairments to partially preserve performance. State-performance correlations support a model wherein reconsolidation of hippocampus-dependent familiar memories occurs during REM sleep, novel information is incorporated and consolidated during TR, and dorsal striatum-dependent procedural learning is augmented during SWS.

Antidepressant Suppression of Non-REM Sleep Spindles and REM Sleep Impairs Hippocampus-Dependent Learning While Augmenting Striatum-Dependent Learning

PubMed Central

Watts, Alain; Gritton, Howard J.; Sweigart, Jamie

2012-01-01

Rapid eye movement (REM) sleep enhances hippocampus-dependent associative memory, but REM deprivation has little impact on striatum-dependent procedural learning. Antidepressant medications are known to inhibit REM sleep, but it is not well understood if antidepressant treatments impact learning and memory. We explored antidepressant REM suppression effects on learning by training animals daily on a spatial task under familiar and novel conditions, followed by training on a procedural memory task. Daily treatment with the antidepressant and norepinephrine reuptake inhibitor desipramine (DMI) strongly suppressed REM sleep in rats for several hours, as has been described in humans. We also found that DMI treatment reduced the spindle-rich transition-to-REM sleep state (TR), which has not been previously reported. DMI REM suppression gradually weakened performance on a once familiar hippocampus-dependent maze (reconsolidation error). DMI also impaired learning of the novel maze (consolidation error). Unexpectedly, learning of novel reward positions and memory of familiar positions were equally and oppositely correlated with amounts of TR sleep. Conversely, DMI treatment enhanced performance on a separate striatum-dependent, procedural T-maze task that was positively correlated with the amounts of slow-wave sleep (SWS). Our results suggest that learning strategy switches in patients taking REM sleep-suppressing antidepressants might serve to offset sleep-dependent hippocampal impairments to partially preserve performance. State–performance correlations support a model wherein reconsolidation of hippocampus-dependent familiar memories occurs during REM sleep, novel information is incorporated and consolidated during TR, and dorsal striatum-dependent procedural learning is augmented during SWS. PMID:23015432

Interfacial Dzyaloshinskii-Moriya interaction sign in Ir/Co2FeAl systems investigated by Brillouin light scattering

NASA Astrophysics Data System (ADS)

Belmeguenai, M.; Gabor, M. S.; Roussigné, Y.; Petrisor, T.; Mos, R. B.; Stashkevich, A.; Chérif, S. M.; Tiusan, C.

2018-02-01

C o2FeAl (CFA) ultrathin films, of various thicknesses (0.9 nm ≤tCFA≤1.8 nm ), have been grown by sputtering on Si substrates, using Ir as a buffer layer. The magnetic properties of these structures have been studied by vibrating sample magnetometry (VSM), miscrostrip ferromagnetic resonance (MS-FMR), and Brillouin light scattering (BLS) in the Damon-Eshbach geometry. VSM characterizations show that films are mostly in-plane magnetized and the saturating field perpendicular to the film plane increases with decreasing CFA thickness suggesting the existence of a perpendicular interface anisotropy. The presence of a magnetic dead layer of 0.44 nm has been detected by VSM. The MS-FMR with the magnetic field applied perpendicularly to the film plane has been used to determine the gyromagnetic factor. The BLS measurements reveal a pronounced nonreciprocal spin wave propagation, due to the interfacial Dzyaloshinskii-Moriya interaction (DMI) induced by the Ir interface with CFA, which increases with decreasing CFA thickness. The DMI sign has been found to be the same (negative) as that of Pt/Co, in contrast to the ab initio calculation on Ir/Co, where it is found to be positive. The thickness dependence of the effective DMI constant shows the existence of two regimes similarly to that of the perpendicular anisotropy constant. The surface DMI constant Ds was estimated to be -0.37 pJ /m for the thickest samples, where a linear thickness dependence of the effective DMI constant has been observed.

In-service testing of Ni{sub 3}Al coupons and trays in carburizing furnaces at Delphi Saginaw. CRADA final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sikka, V.K.; Santella, M.L.; Viswanathan, S.

1998-08-01

This Cooperative Research and Development Agreement (CRADA) report deals with the development of nickel aluminide alloy for improved longer life heat-resistant fixture assemblies for batch and continuous pusher carburizing furnaces. The nickel aluminide development was compared in both coupon and component testing with the currently used Fe-Ni-Cr heat-resisting alloy known as HU. The specific goals of the CRADA were: (1) casting process development, (2) characterization and possible modification of the alloy composition to optimize its manufacturing ability and performance under typical furnace operating conditions, and (3) testing and evaluation of specimens and prototype fixtures. In support of the CRADA objectives,more » coupons of nickel aluminide and the HU alloy were installed in both batch and pusher furnaces. The coupons were taken from two silicon levels and contained welds made with two different filler compositions (IC-221LA and IC-221W). Both nickel-aluminide and HU coupons were removed from the batch and pusher carburizing furnace at time intervals ranging from one month to one year. The exposed coupons were cut and mounted for metallographic, hardness, and microprobe analysis. The results of the microstructural analysis have been transmitted to General Motors Corporation, Saginaw Division (Delphi Saginaw) through reports that were presented at periodic CRADA review meetings. Based on coupon testing and verification of the coupon results with the testing of trays, Delphi Saginaw moved forward with the use of six additional trays in a batch furnace and two assemblies in a pusher furnace. Fifty percent of the trays and fixtures are in the as-cast condition and the remaining trays and fixtures are in the preoxidized condition. The successful operating experience of two assemblies in the pusher furnace for nearly a year formed the basis for a production run of 63 more assemblies. The production run required melting of 94 heats weighing 500 lb. each. Twenty-six of the 94 heats were from virgin stock, and 68 were from the revert that used 50% virgin and 50% revert. Detailed chemical analysis of the 94 heats reflected that the nickel aluminide can be cast into heat-treat fixtures under production conditions. In addition to the chemical analysis, the castings showed excellent dimensional reproducibility. A total of six batch furnace trays and 65 pusher furnace assemblies of nickel aluminide alloy IC-221M are currently operating in production furnaces at Delphi Saginaw. Two of the pusher furnace assemblies have completed two years of service without any failure. The CRADA has accomplished the goal of demonstrating that the nickel aluminide can be produced under commercial production conditions and it has superior performance over the currently used HU alloy in both batch and pusher furnaces.« less

Can live weight be used as a proxy for enteric methane emissions from pasture-fed sheep?

PubMed Central

Moorby, J. M.; Fleming, H. R.; Theobald, V. J.; Fraser, M. D.

2015-01-01

To test the hypothesis that sheep live weight (LW) could be used to improve enteric methane (CH4) emission calculations, mature ewes of 4 different breeds representative of the UK sheep industry were studied: Welsh Mountain, Scottish Blackface, Welsh Mule and Texel (n = 8 per breed). The ewes were housed and offered ad libitum access to fresh cut pasture of three different types, varying in digestibility: (a) a relatively high digestibility monoculture of perennial ryegrass (Lolium perenne), (b) a medium digestibility permanent pasture comprising a range of grass species, and (c) a relatively low digestibility native grassland pasture comprising mainly Molinia caerulea. Individual LW, feed dry matter intake (DMI), and CH4 emissions in chambers were measured. The linear functional relationship between DMI and CH4 emissions was positive (r = 0.77) with little breed effect. The relationships between LW and DMI, and LW and CH4 emissions were also positive but weaker, regardless of pasture type. It is concluded that change to LW was a poor indicator of DMI and has limited value in the prediction of enteric CH4 emissions from mature ewes. PMID:26647754

Dzyaloshinskii-Moriya interaction in α -Fe2O3 measured by magnetic circular dichroism in resonant inelastic soft x-ray scattering

NASA Astrophysics Data System (ADS)

Miyawaki, Jun; Suga, Shigemasa; Fujiwara, Hidenori; Urasaki, Masato; Ikeno, Hidekazu; Niwa, Hideharu; Kiuchi, Hisao; Harada, Yoshihisa

2017-12-01

Fe L2 ,3-edge x-ray absorption spectra (XAS) and magnetic circular dichroism (MCD) in resonant inelastic x-ray scattering (RIXS) of α -Fe2O3 were measured to identify the electronic structure responsible for its weak ferromagnetism caused by the Dzyaloshinskii-Moriya interaction (DMI) at room temperature. In contrast to negligible MCD in XAS, MCD in RIXS (RIXS-MCD) was clearly observed in the d d excitation at 1.8 eV via excitation to charge-transfer states. Furthermore, RIXS-MCD showed a crystal orientation dependence, indicating that the observed RIXS-MCD originated from DMI. The observed RIXS-MCD is well described by ab initio charge-transfer multiplet calculations, revealing that the RIXS-MCD derives from spin flip excitations at delocalized eg orbitals. By the combination of the experiments and calculations, RIXS-MCD has unraveled that the origin of DMI in α -Fe2O3 is the eg orbitals, which are strongly hybridized with the 2 p orbitals of oxygen atoms. The results demonstrate the importance of RIXS-MCD for identifying the electronic structure related to DMI.

Comparison of the effects of acute fluvoxamine and desipramine administration on melatonin and cortisol production in humans.

PubMed Central

Skene, D J; Bojkowski, C J; Arendt, J

1994-01-01

1. Acute administration of the specific serotonin uptake inhibitor, fluvoxamine (100 mg at 16.00 h), markedly increased nocturnal plasma melatonin concentrations, with high levels extending into the morning hours. 2. Acute administration of the noradrenaline uptake inhibitor, desipramine (DMI) (100 mg at 16.00 h), increased evening plasma melatonin concentrations. 3. Both drug treatments increased the duration of melatonin secretion, fluvoxamine significantly delaying the offset time and DMI significantly advancing the onset time. 4. The stimulatory effect of DMI on plasma melatonin was mirrored by increased urinary 6-sulphatoxymelatonin (aMT6s) excretion. 5. On the contrary, there was no correlation between plasma melatonin and urinary aMT6s concentrations following fluvoxamine treatment, suggesting that fluvoxamine may inhibit the metabolism of melatonin. 6. Treatment with DMI increased plasma cortisol concentrations in the evening and early morning, treatment with fluvoxamine increased plasma cortisol at 03.00 h, 10.00 h and 11.00 h. 7. The drug treatments affected different aspects of the nocturnal plasma melatonin profile suggesting that the amplitude of the melatonin rhythm may depend upon serotonin availability and/or melatonin metabolism whilst the onset of melatonin production depends upon noradrenaline availability. PMID:8186063

Dispersive elastic properties of Dzyaloshinskii domain walls

NASA Astrophysics Data System (ADS)

Pellegren, James; Lau, Derek; Sokalski, Vincent

Recent studies on the asymmetric field-driven growth of magnetic bubble domains in perpendicular thin films exhibiting an interfacial Dzyaloshinskii-Moriya interaction (DMI) have provided a wealth of experimental evidence to validate models of creep phenomena, as key properties of the domain wall (DW) can be altered with the application of an external in-plane magnetic field. While asymmetric growth behavior has been attributed to the highly anisotropic DW energy, σ (θ) , which results from the combination of DMI and the in-plane field, many experimental results remain anomalous. In this work, we demonstrate that the anisotropy of DW energy alters the elastic response of the DW as characterized by the surface stiffness, σ (θ) = σ (θ) + σ (θ) , and evaluate the impact of this stiffness on the creep law. We find that at in-plane fields larger than and antiparallel to the effective field due to DMI, the DW stiffness decreases rapidly, suggesting that higher energy walls can actually become more mobile than their low energy counterparts. This result is consistent with experiments on CoNi multilayer films where velocity curves for domain walls with DMI fields parallel and antiparallel to the applied field cross over at high in-plane fields.

Dry period management and optimization of post-partum reproductive management in dairy cattle.

PubMed

Gumen, A; Keskin, A; Yilmazbas-Mecitoglu, G; Karakaya, E; Wiltbank, Mc

2011-09-01

Dry period and early post-partum management are decisive factors for fertility in lactating dairy cows. Previous studies have shown that decreased dry matter intake (DMI) and increased non-esterified fatty acids (NEFA) negatively affect fertility and subsequent milk production. The traditional dry period decreases DMI prior to parturition, resulting in a decrease in energy intake. A negative energy balance increases NEFA concentration, and increased NEFA may impair the immune system, especially by decreasing neutrophil function prior to parturition. Earlier studies have shown that post-partum health disorders, including retained placenta and metritis, were correlated with periparturient neutrophil function. In addition, decreased DMI is also linked to a reduced body condition score (BCS) in dairy cows. These events in the periparturient period negatively affect fertility. Some manipulation, such as shortening the dry period, may be a solution to increased DMI in the periparturient period, preventing post-partum disorders and subsequent fertility issues. This article aims to explain the effects of shortening the dry period on reproduction and early post-partum treatments to improve fertility. In addition, timed artificial insemination protocols will be discussed for use during the post-partum period to improve fertility in dairy cows. © 2011 Blackwell Verlag GmbH.

Development Of A Magnetic Directional-Solidification Furnace

NASA Technical Reports Server (NTRS)

Aldrich, Bill R.; Lehoczky, Sandor L.

1996-01-01

Report describes development of directional-solidification furnace in which axial magnetic field is imposed by surrounding ring permanent magnets and/or electromagnets and pole pieces. Furnace provides controlled axial temperature gradients in multiple zones, through which ampoule containing sample of material to be solidified is translated at controlled speed by low-vibration, lead-screw, stepping-motor-driven mechanism. Intended for use in low-gravity (spaceflight) experiments on melt growth of high-purity semiconductor crystals.

Tunable Snell's law for spin waves in heterochiral magnetic films

NASA Astrophysics Data System (ADS)

Mulkers, Jeroen; Van Waeyenberge, Bartel; Milošević, Milorad V.

2018-03-01

Thin ferromagnetic films with an interfacially induced DMI exhibit nontrivial asymmetric dispersion relations that lead to unique and useful magnonic properties. Here we derive an analytical expression for the magnon propagation angle within the micromagnetic framework and show how the dispersion relation can be approximated with a comprehensible geometrical interpretation in the k space of the propagation of spin waves. We further explore the refraction of spin waves at DMI interfaces in heterochiral magnetic films, after deriving a generalized Snell's law tunable by an in-plane magnetic field, that yields analytical expressions for critical incident angles. The found asymmetric Brewster angles at interfaces of regions with different DMI strengths, adjustable by magnetic field, support the conclusion that heterochiral ferromagnetic structures are an ideal platform for versatile spin-wave guides.

Elements of EAF automation processes

NASA Astrophysics Data System (ADS)

Ioana, A.; Constantin, N.; Dragna, E. C.

2017-01-01

Our article presents elements of Electric Arc Furnace (EAF) automation. So, we present and analyze detailed two automation schemes: the scheme of electrical EAF automation system; the scheme of thermic EAF automation system. The application results of these scheme of automation consists in: the sensitive reduction of specific consummation of electrical energy of Electric Arc Furnace, increasing the productivity of Electric Arc Furnace, increase the quality of the developed steel, increasing the durability of the building elements of Electric Arc Furnace.

High temperature aircraft research furnace facilities

NASA Technical Reports Server (NTRS)

Smith, James E., Jr.; Cashon, John L.

1992-01-01

Focus is on the design, fabrication, and development of the High Temperature Aircraft Research Furnace Facilities (HTARFF). The HTARFF was developed to process electrically conductive materials with high melting points in a low gravity environment. The basic principle of operation is to accurately translate a high temperature arc-plasma gas front as it orbits around a cylindrical sample, thereby making it possible to precisely traverse the entire surface of a sample. The furnace utilizes the gas-tungsten-arc-welding (GTAW) process, also commonly referred to as Tungsten-Inert-Gas (TIG). The HTARFF was developed to further research efforts in the areas of directional solidification, float-zone processing, welding in a low-gravity environment, and segregation effects in metals. The furnace is intended for use aboard the NASA-JSC Reduced Gravity Program KC-135A Aircraft.

Anti-methanogenic effects of monensin in dairy and beef cattle: a meta-analysis.

PubMed

Appuhamy, J A D Ranga Niroshan; Strathe, A B; Jayasundara, S; Wagner-Riddle, C; Dijkstra, J; France, J; Kebreab, E

2013-08-01

Monensin is a widely used feed additive with the potential to minimize methane (CH4) emissions from cattle. Several studies have investigated the effects of monensin on CH4, but findings have been inconsistent. The objective of the present study was to conduct meta-analyses to quantitatively summarize the effect of monensin on CH4 production (g/d) and the percentage of dietary gross energy lost as CH4 (Ym) in dairy cows and beef steers. Data from 22 controlled studies were used. Heterogeneity of the monensin effects were estimated using random effect models. Due to significant heterogeneity (>68%) in both dairy and beef studies, the random effect models were then extended to mixed effect models by including fixed effects of DMI, dietary nutrient contents, monensin dose, and length of monensin treatment period. Monensin reduced Ym from 5.97 to 5.43% and diets with greater neutral detergent fiber contents (g/kg of dry matter) tended to enhance the monensin effect on CH4 in beef steers. When adjusted for the neutral detergent fiber effect, monensin supplementation [average 32 mg/kg of dry matter intake (DMI)] reduced CH4 emissions from beef steers by 19±4 g/d. Dietary ether extract content and DMI had a positive and a negative effect on monensin in dairy cows, respectively. When adjusted for these 2 effects in the final mixed-effect model, monensin feeding (average 21 mg/kg of DMI) was associated with a 6±3 g/d reduction in CH4 emissions in dairy cows. When analyzed across dairy and beef cattle studies, DMI or monensin dose (mg/kg of DMI) tended to decrease or increase the effect of monensin in reducing methane emissions, respectively. Methane mitigation effects of monensin in dairy cows (-12±6 g/d) and beef steers (-14±6 g/d) became similar when adjusted for the monensin dose differences between dairy cow and beef steer studies. When adjusted for DMI differences, monensin reduced Ym in dairy cows (-0.23±0.14) and beef steers (-0.33±0.16). Monensin treatment period length did not significantly modify the monensin effects in dairy cow or beef steer studies. Overall, monensin had stronger antimethanogenic effects in beef steers than dairy cows, but the effects in dairy cows could potentially be improved by dietary composition modifications and increasing the monensin dose. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Modeling Specular Exchange Between Concentric Cylinders in a Radiative Shielded Furnace

NASA Technical Reports Server (NTRS)

Schunk, Richard Gregory; Wessling, Francis C.

2000-01-01

The objective of this research is to develop and validate mathematical models to characterize the thermal performance of a radiative shielded furnace, the University of Alabama in Huntsville (UAH) Isothermal Diffusion Oven. The mathematical models are validated against experimental data obtained from testing the breadboard oven in a terrestrial laboratory environment. It is anticipated that the validation will produce math models capable of predicting the thermal performance of the furnace over a wide range of operating conditions, including those for which no experimental data is available. Of particular interest is the furnace core temperature versus heater power parametric and the transient thermal response of the furnace. Application to a microgravity environment is not considered, although it is conjectured that the removal of any gravity dependent terms from the math models developed for the terrestrial application should yield adequate results in a microgravity environment. The UAH Isothermal Diffusion Oven is designed to provide a thermal environment that is conducive to measuring the diffusion of high temperature liquid metals. In addition to achieving the temperatures required to melt a sample placed within the furnace, reducing or eliminating convective motions within the melt is an important design consideration [1]. Both of these influences are reflected in the design of the furnace. Reducing unwanted heat losses from the furnace is achieved through the use of low conductivity materials and reflective shielding. As evidenced by the highly conductive copper core used to house the sample within the furnace, convective motions can be greatly suppressed by providing an essentially uniform thermal environment. An oven of this design could ultimately be utilized in a microgravity environment, presumably as a experiment payload. Such an application precipitates other design requirements that limit the resources available to the furnace such as power, mass, volume, and possibly even time. Through the experimental and numerical results obtained, the power requirements and thermal response time of the breadboard furnace are quantified.

Effects of a dietary Aspergillus oryzae extract containing alpha-amylase activity on performance and carcass characteristics of finishing beef cattle.

PubMed

Tricarico, J M; Abney, M D; Galyean, M L; Rivera, J D; Hanson, K C; McLeod, K R; Harmon, D L

2007-03-01

Three experiments were conducted to examine the effects of an Aspergillus oryzae extract containing alpha-amylase activity on performance and carcass characteristics of finishing beef cattle. In Exp. 1, 120 crossbred steers were used in a randomized complete block design to evaluate the effects of roughage source (alfalfa hay vs. cottonseed hulls) and supplemental alpha-amylase at 950 dextrinizing units (DU)/kg of DM. Significant roughage source x alpha-amylase interactions (P < 0.05) were observed for performance. In steers fed cottonseed hulls, supplemental alpha-amylase increased ADG through d 28 and 112 and tended (P < 0.15) to increase ADG in all other periods. The increases in ADG were related to increased DMI and efficiency of gain during the initial 28-d period but were primarily related to increased DMI as the feeding period progressed. Supplemental alpha-amylase increased (P = 0.02) the LM area across both roughage sources. In Exp. 2, 96 crossbred heifers were used in a randomized complete block design with a 2 x 3 factorial arrangement of treatments to evaluate the effects of corn processing (dry cracked vs. high moisture) and supplemental alpha-amylase concentration (0, 580, or 1,160 DU/kg of DM). Alpha-amylase supplementation increased DMI (P = 0.05) and ADG (P = 0.03) during the initial 28 d on feed and carcass-adjusted ADG (P = 0.04) across corn processing methods. Longissimus muscle area was greatest (quadratic effect, P = 0.04), and yield grade was least (quadratic effect, P = 0.02) in heifers fed 580 DU of alpha-amylase/kg of DM across corn processing methods. In Exp. 3, 56 crossbred steers were used in a randomized complete block design to evaluate the effects of supplemental alpha-amylase (930 DU/kg of DM) on performance when DMI was restricted to yield a programmed ADG. Alpha-amylase supplementation did not affect performance when DMI was restricted. We conclude that dietary alpha-amylase supplementation of finishing beef diets may result in increased ADG through increased DMI under certain dietary conditions and that further research is warranted to explain its mode of action and interactions with dietary ingredients.

Energy Saving Devices on Gas Furnaces.

DTIC Science & Technology

1980-03-01

AO-A082 0715 JOHNS - MANVILLE SALES CORP DENVER CO RESEARCH AND DEV--ETC FIG 1311 ENERGY SAVING DEVICES ON GAS FURNACES.(U) MAR B0 T E BRISBANE, P B...DEVICES FOR GAS FURNACES THOMAS E. BRISBANE ,o"’ P. B. SHEPHERD JOHNS - MANVILLE SALES CORPORATION RESEARCH & DEVELOPMENT CENTER KEN-CARYL RANCH, DENVER

Improved Casting Furnace Conceptual Design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fielding, Randall Sidney; Tolman, David Donald

In an attempt to ensure more consistent casting results and remove some schedule variance associated with casting, an improved casting furnace concept has been developed. The improved furnace uses the existing arc melter hardware and glovebox utilities. The furnace concept was designed around physical and operational requirements such as; a charge sized of less than 30 grams, high heating rates and minimal additional footprint. The conceptual model is shown in the report as well as a summary of how the requirements were met.

Effect of pig bodyweight on ileal amino acid endogenous losses after ingestion of a protein-free diet enriched in pea inner fibre isolates.

PubMed

Leterme, Pascal; Théwis, André

2004-01-01

The present study was conducted to evaluate whether bodyweight and the micronisation of dietary fibre affect the endogenous nitrogen and amino acid losses (ENL and EAAL) in pigs. The effect of the micronising process was tested by providing pigs with 90 g DM x kg(-1) BW0.75 of a N-free diet supplemented with isolated pea inner fibres, presented in native or micronised form and with a water-holding capacity of 12 and 4 g water g(-1) DM, respectively. ENL and EAAL were measured on pigs weighing 24, 62 and 105 kg. In all cases, daily ENL increased linearly (P < 0.05) with BW, for the majority of the AA and total N. As BW increased, daily ENL, total EAAL and the majority of EAAL increased linearly independently of micronisation (P < 0.05). When expressed per kg DMI, total EAAL and the majority of each EAA decreased curvilinearly and reached nadir at around 100 kg BW. For ENL expressed per kg DMI, micronisation resulted in a curvilinear decrease with increasing BW, as compared to a linear decrease for pigs fed the native pea fibre diet (non-micronised). Micronisation of pea inner fibres did not decrease ENL or EAAL daily, except for proline. When the losses were expressed as g x k(-1)g DMI, micronisation did not decrease ENL but decreased (P < 0.05) endogenous losses for a majority of AA as well as for total AA. The results suggest that small pigs excrete more endogenous N per kg DMI than large pigs and that pea fibre micronisation reduces EAAL but not ENL when expressed per kg DMI.

Reduction of high-affinity beta2-adrenergic receptor binding by hyperforin and hyperoside on rat C6 glioblastoma cells measured by fluorescence correlation spectroscopy.

PubMed

Prenner, Lars; Sieben, Anne; Zeller, Karin; Weiser, Dieter; Häberlein, Hanns

2007-05-01

Beta-adrenergic receptors (beta-AR) are potential targets for antidepressants. Desensitization and downregulation of beta-AR are discussed as possible modes of action for antidepressants. We have investigated the effects of hyperforin and hyperoside, compounds with potentially antidepressant activity from St. John's Wort, on the binding behavior and dynamics of beta2-AR in living rat C6 glioblastoma cells, compared to desipramine (desmethylimipramine; DMI) by means of fluorescence correlation spectroscopy (FCS) and fluorescence microscopy. FCS-binding studies with the fluorescently labeled ligand Alexa532-noradrenaline (Alexa532-NA) binding to beta2-AR of C6 cells showed a significant reduction in total beta2-AR binding after preincubation with hyperforin and hyperoside for 3 days, respectively, which was also found for DMI. This was mainly observed in high-affinity receptor-ligand complexes with hindered lateral mobility (D2 = 1.1 (+/-0.4) microm2/s) in the biomembrane. However, internalization of beta2-AR was found neither in z-scans of these C6 cells nor in HEK 293 cells stably transfected with GFP-tagged beta2-adrenergic receptors (beta2AR-GFP) after incubation up to 6 days with either DMI, hyperforin, or hyperoside. Thus, under these conditions reduction of beta2-AR binding was not mediated by receptor internalization. Additionally, preincubation of C6 cells with DMI, hyperforin, and hyperoside led to a loss of second messenger cAMP after beta2-adrenergic stimulating conditions with terbutaline. Our current results indicate that hyperforin and hyperoside from St. John's Wort, as well as DMI, reduce beta2-adrenergic sensitivity in C6 cells, emphasizing the potential usefulness of St. John's Wort dry extracts in clinical treatment of depressive symptoms.

Degradation of Phthalate Esters by Fusarium sp. DMT-5-3 and Trichosporon sp. DMI-5-1 Isolated from Mangrove Sediments.

PubMed

Luo, Zhu-Hua; Pang, Ka-Lai; Wu, Yi-Rui; Gu, Ji-Dong; Chow, Raymond K K; Vrijmoed, L L P

2012-01-01

Phthalate esters (PAEs) are important industrial compounds mainly used as plasticizers to increase flexibility and softness of plastic products. PAEs are of major concern because of their widespread use, ubiquity in the environment, and endocrine-disrupting toxicity. In this study, two fungal strains, Fusarium sp. DMT-5-3 and Trichosporon sp. DMI-5-1 which had the capability to degrade dimethyl phthalate esters (DMPEs), were isolated from mangrove sediments in the Futian Nature Reserve of Shenzhen, China, by enrichment culture technique. These fungi were identified on the basis of spore morphology and molecular typing using 18S rDNA sequence. Comparative investigations on the biodegradation of three isomers of DMPEs, namely dimethyl phthalate (DMP), dimethyl isophthalate (DMI), and dimethyl terephthalate (DMT), were carried out with these two fungi. It was found that both fungi could not completely mineralize DMPEs but transform them to the respective monomethyl phthalate or phthalate acid. Biochemical degradation pathways for different DMPE isomers by both fungi were different. Both fungi could transform DMT to monomethyl terephthalate (MMT) and further to terephthalic acid (TA) by stepwise hydrolysis of two ester bonds. However, they could only carry out one-step ester hydrolysis to transform DMI to monomethyl isophthalate (MMI). Further metabolism of MMI did not proceed. Only Trichosporon sp. was able to transform DMP to monomethyl phthalate (MMP) but not Fusarium sp. The optimal pH for DMI and DMT degradation by Fusarium sp. was 6.0 and 4.5, respectively, whereas for Trichosporon sp., the optimal pH for the degradation of all the three DMPE isomers was at 6.0. These results suggest that the fungal esterases responsible for hydrolysis of the two ester bonds of PAEs are highly substrate specific.

Diet quality and the risk of cardiovascular disease: the Women's Health Initiative (WHI)123

PubMed Central

Belin, Rashad J; Greenland, Philip; Allison, Matthew; Martin, Lisa; Shikany, James M; Larson, Joseph; Tinker, Lesley; Howard, Barbara V; Lloyd-Jones, Donald

2011-01-01

Background: The association between diet quality and risk of incident cardiovascular disease (CVD) or heart failure (HF) in postmenopausal women is uncertain. Objective: This study aimed to determine whether a conventional index [Alternate Healthy Eating Index (AHEI)] or a novel index [Women's Health Initiative (WHI) Dietary Modification Index (DMI)] of diet quality was associated with the risk of incident CVD or HF in the WHI Observational Study (WHI-OS). Design: The WHI-OS is an observational cohort study of 93,676 women aged 50–79 y of diverse ethnicity and backgrounds followed for an average of 10.0 y for CVD events. The individual components of the AHEI and DMI were determined from the baseline WHI food-frequency questionnaire. Incident CVD was a composite of nonfatal myocardial infarction, coronary heart disease death, stroke, coronary revascularization, and incident HF. The association between AHEI or DMI and incident CVD or incident HF was determined by using Cox models adjusted for traditional CVD and HF risk factors. Results: Women with a DMI in the highest quintile had hazard ratios (HRs) of 0.88 (95% CI: 0.80, 0.95) and 0.91 (95% CI: 0.78, 1.06) for incident CVD and HF, respectively. Women with an AHEI in the highest quintile had HRs of 0.77 (95% CI: 0.70, 0.84) and 0.70 (95% CI: 0.59, 0.82) for incident CVD and HF, respectively. Conclusion: Overall, adherence to current nutrient guidelines (as indexed by the DMI) are associated with lower total CVD risk, and additional dietary factors (as indexed by the AHEI) were associated with a lower risk of CVD and HF. PMID:21613562

SITE - DEMONSTRATION BULLETIN - MINERGY GLASS FURNACE TECHNOLOGY - MINERGY CORPORATION

EPA Science Inventory

The Glass Furnace Technology (GFT) was developed by Minergy Corporation (Minergy), of Waukesha, Wisconsin. Minergy originally developed vitrification technologies to process wastewater sludge into glass aggregate that could be sold as a commercial product. Minergy modified a st...

Ultralight mesoporous magnetic frameworks by interfacial assembly of Prussian blue nanocubes.

PubMed

Kong, Biao; Tang, Jing; Wu, Zhangxiong; Wei, Jing; Wu, Hao; Wang, Yongcheng; Zheng, Gengfeng; Zhao, Dongyuan

2014-03-10

A facile approach for the synthesis of ultralight iron oxide hierarchical structures with tailorable macro- and mesoporosity is reported. This method entails the growth of porous Prussian blue (PB) single crystals on the surface of a polyurethane sponge, followed by in situ thermal conversion of PB crystals into three-dimensional mesoporous iron oxide (3DMI) architectures. Compared to previously reported ultralight materials, the 3DMI architectures possess hierarchical macro- and mesoporous frameworks with multiple advantageous features, including high surface area (ca. 117 m(2) g(-1)) and ultralow density (6-11 mg cm(-3)). Furthermore, they can be synthesized on a kilogram scale. More importantly, these 3DMI structures exhibit superparamagnetism and tunable hydrophilicity/hydrophobicity, thus allowing for efficient multiphase interfacial adsorption and fast multiphase catalysis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A high-temperature furnace for applications in microgravity

NASA Technical Reports Server (NTRS)

1991-01-01

Technology in the area of material processing and crystal growth has been greatly furthered by research in microgravity environments. The role of efficient, lightweight furnaces with reliable performance is crucial in these experiments. A need exists for the development of a readily duplicated, high-temperature furnace satisfying stringent weight, volume, and power constraints. A furnace was designed and is referred to as the UAH SHIELD. Stringent physical and operating characteristics for the system were specified, including a maximum weight of 20 kg, a maximum power requirement of 60 W, and a volume of the furnace assembly, excluding the batteries, limited to half a Get-Away-Special canister. The UAH SHIELD furnace uses radiation shield and vacuum technology applied in the form of a series of concentric cylinders enclosed on either end with disks. Thermal testing of a furnace prototype was performed in addition to some thermal and structural analysis. Results indicate the need for spacing of the shields to accommodate the thermal expansion during furnace operation. In addition, a power dissipation of approximately 100 W and system weight of approximately 30 kg was found for the current design.

Changes in acyl and total ghrelin concentrations and their association with dry matter intake, average daily gain, and feed efficiency of finishing beef steers and heifers

USDA-ARS?s Scientific Manuscript database

Ghrelin is a peptide hormone produced in the gut that is implicated in signaling appetite and regulating DMI. The objective of this experiment was to determine the change in acyl ghrelin, total ghrelin, and the ghrelin ratio (acyl ghrelin/total ghrelin) over an 84-d DMI and ADG measurement period a...

Age-related changes in the antidepressant-like effect of desipramine and fluoxetine in the rat forced-swim test.

PubMed

Olivares-Nazario, Maribel; Fernández-Guasti, Alonso; Martínez-Mota, Lucía

2016-02-01

Some reports suggest that older patients are less responsive to antidepressants than young adults, but this idea has not been fully supported. Here, we investigated the role of aging in the behavioral effects of the antidepressants, desipramine (DMI) (5, 10, and 20 mg/kg) and fluoxetine (FLX) (5, 10, and 20 mg/kg) in young adults (3-5 months), middle-aged (MA, 12-15 months), and senescent (SE, 23-25 months) male rats in the forced-swim test. In addition, locomotor activity and motor coordination were assessed as side-effects. DMI and fluoxetine produced an antidepressant-like effect in YA and MA animals, although in the latter group, a shift to the right in the dose-response curve was found for DMI. Importantly, neither drug was effective in SE animals. Motor side-effects were produced mainly by DMI in MA and SE rats. Therefore, a decrease in the antidepressant-like effect is associated strongly with senescence as well as an increased vulnerability to motor side-effects, particularly of tricyclics. This study is significant because SE animals are scarcely studied in pharmacological screening tests, and our findings might be useful for improving antidepressant treatments for the increasing aged population.

Microgravity

NASA Image and Video Library

1995-09-15

Large Isothermal Furnace (LIF) was flown on a mission in cooperation with the National Space Development Agency (NASDA) of Japan. LIF is a vacuum-heating furnace designed to heat large samples uniformly. The furnace consists of a sample container and heating element surrounded by a vacuum chamber. A crewmemeber will insert a sample cartridge into the furnace. The furnace will be activated and operations will be controlled automatically by a computer in response to an experiment number entered on the control panel. At the end of operations, helium will be discharged into the furnace, allowing cooling to start. Cooling will occur through the use of a water jacket while rapid cooling of samples can be accomplished through a controlled flow of helium. Data from experiments will help scientists better understand this important process which is vital to the production of high-quality semiconductor crystals.

Programmable multi-zone furnace for microgravity research

NASA Technical Reports Server (NTRS)

Rosenthal, Bruce N.; Krolikowski, Cathryn R.

1991-01-01

In order to provide new furnace technology to accommodate microgravity research studies and commercial applications in material processes, research has been initiated on the development of the Programmable-Multi-zone Furnace (PMZF). The PMZF is described as a multi-user materials processing furnace facility that is composed of thirty or more heater elements in series on a muffle tube or in a stacked ring-type configuration and independently controlled by a computer. One of the aims of the PMZF project is to allow furnace thermal gradient profiles to be reconfigured without physical modification of the hardware by creating the capability of reconfiguring thermal profiles in response to investigators' requests. The future location of the PMZF facility is discussed; the preliminary science survey results and preliminary conceptual designs for the PMZF are presented; and a review of multi-zone furnace technology is given.

Development of NASA's Sample Cartridge Assembly: Summary of GEDS Design, Development Testing, and Thermal Analyses

NASA Technical Reports Server (NTRS)

O'Connor, Brian; Hernandez, Deborah; Hornsby, Linda; Brown, Maria; Horton-Mullins, Kathryn

2017-01-01

Outline: Background of ISS (International Space Station) Material Science Research Rack; NASA SCA (Sample Cartridge Assembly) Design; GEDS (Gravitational Effects in Distortion in Sintering) Experiment Ampoule Design; Development Testing Summary; Thermal Modeling and Analysis. Summary: GEDS design development challenging (GEDS Ampoule design developed through MUGS (Microgravity) testing; Short duration transient sample processing; Unable to measure sample temperatures); MUGS Development testing used to gather data (Actual LGF (Low Gradient Furnace)-like furnace response; Provided sample for sintering evaluation); Transient thermal model integral to successful GEDS experiment (Development testing provided furnace response; PI (Performance Indicator) evaluation of sintering anchored model evaluation of processing durations; Thermal transient model used to determine flight SCA sample processing profiles).

STS-47 MS Davis uses SLJ Rack 8 continuous heating furnace (CHF) on OV-105

NASA Image and Video Library

1992-09-20

STS047-02-003 (12 - 20 Sept 1992) --- Astronaut N. Jan Davis, mission specialist, works at the Continuous Heating Furnace (CHF) in the Spacelab-J Science Module. This furnace provided temperatures up to 1,300 degrees Celsius and rapid cooling to two sets of samples concurrently. The furnace accommodated in-space experiments in the Fabrication of Si-As-Te:Ni Ternary Amorphous Semiconductor and the Crystal Growth of Compound Semiconductors. These were two of the many experiments designed and monitored by Japan's National Space Development Agency (NASDA).

Settling of Inclusions in Holding Furnaces: Modeling and Experimental Results

NASA Astrophysics Data System (ADS)

Sztur, C.; Balestreri, F.; Meyer, JL.; Hannart, B.

Description of settling phenomena usually refers to falling particles in a liquid, following Stokes law. But the thermal convection always takes place in holding furnaces due to temperature heterogeneity, and the behaviour of the inclusions can be dramatically influenced by the liquid metal motion. A numerical model based on turbulent fluid flow calculations in an holding furnace and on trajectories calculations of a family of inclusions has been developed. Results are compared with experiments on a lab. scale and on an industrial scale furnace. An analysis of the governing parameters will be presented.

Technical Update: Johnson Space Center system using a solid electrolytic cell in a remote location to measure oxygen fugacities in CO/CO2 controlled-atmosphere furnaces

NASA Technical Reports Server (NTRS)

Jurewicz, A. J. G.; Williams, R. J.; Le, L.; Wagstaff, J.; Lofgren, G.; Lanier, A.; Carter, W.; Roshko, A.

1993-01-01

Details are given for the design and application of a (one atmosphere) redox-control system. This system differs from that given in NASA Technical Memorandum 58234 in that it uses a single solid-electrolytic cell in a remote location to measure the oxygen fugacities of multiple CO/CO2 controlled-atmosphere furnaces. This remote measurement extends the range of sample-furnace conditions that can be measured using a solid-electrolytic cell, and cuts costs by extending the life of the sensors and by minimizing the number of sensors in use. The system consists of a reference furnace and an exhaust-gas manifold. The reference furnace is designed according to the redox control system of NASA Technical Memorandum 58234, and any number of CO/CO2 controlled-atmosphere furnaces can be attached to the exhaust-gas manifold. Using the manifold, the exhaust gas from individual CO/CO2 controlled atmosphere furnaces can be diverted through the reference furnace, where a solid-electrolyte cell is used to read the ambient oxygen fugacity. The oxygen fugacity measured in the reference furnace can then be used to calculate the oxygen fugacity in the individual CO/CO2 controlled-atmosphere furnace. A BASIC computer program was developed to expedite this calculation.

Thermal analysis of HGFQ using FIDAP(trademark): Solidification front motion

NASA Technical Reports Server (NTRS)

Woodbury, Keith A.

1996-01-01

The High Gradient Furnace with Quench (HGFQ) is being designed by NASA/MSFC for flight on the International Space Station. The furnace is being designed specifically for solidification experiments in metal and metallic alloy systems. The HGFQ Product development Team (PDT) has been active since January 1994 and their effort is now in early Phase B. Thermal models have been developed both by NASA and Sverdrup (support contractor) to assist in the HGFQ design effort. Both these models use SINDA as a solution engine, but the NASA model was developed using PATRAN and includes more detail than the Sverdrup model. These models have been used to guide design decisions and have been validated through experimentation on a prototypical 'Breadboard' furnace at MSFC. One facet of the furnace operation of interest to the designers is the sensitivity of the solidification interface location to changes in the furnace setpoint. Specifically of interest is the motion (position and velocity) of the solidification front due to a small perturbation in the furnace temperature. FIDAP(TM) is a commercially available finite element program for analysis of heat transfer and fluid flow processes. Its strength is in solution of the Navier-Stokes equations for incompressible flow, but among its capabilities is the analysis of transient processes involving radiation and solidification. The models presently available from NASA and Sverdrup are steady-state models and are incapable of computing the motion of the solidification front. The objective of this investigation is to use FIDAP(TM) to compute the motion of the solidification interface due to a perturbation in the furnace setpoint.

JPRS Report, Near East & South Asia

DTIC Science & Technology

1989-03-16

general manager is Fahmi , no stranger to Islamic banking. He was until recently the acting general manager of Faysal Finance Institution, a subsidiary...of the Geneva-based Dar al-Mal al-Islami (DMI), headed by Prince Muhammad of Saudi Arabia. Fahmi left under controversial circumstances and THE...irregularities. Fahmi has had long-running difficulty with DMI’s top management for the last two years. Islamic bankers in Turkey claim that he has been

Future consequences of decreasing marginal production efficiency in the high-yielding dairy cow.

PubMed

Moallem, U

2016-04-01

The objectives were to examine the gross and marginal production efficiencies in high-yielding dairy cows and the future consequences on dairy industry profitability. Data from 2 experiments were used in across-treatments analysis (n=82 mid-lactation multiparous Israeli-Holstein dairy cows). Milk yields, body weights (BW), and dry matter intakes (DMI) were recorded daily. In both experiments, cows were fed a diet containing 16.5 to 16.6% crude protein and net energy for lactation (NEL) at 1.61 Mcal/kg of dry matter (DM). The means of milk yield, BW, DMI, NEL intake, and energy required for maintenance were calculated individually over the whole study, and used to calculate gross and marginal efficiencies. Data were analyzed in 2 ways: (1) simple correlation between variables; and (2) cows were divided into 3 subgroups, designated low, moderate, and high DMI (LDMI, MDMI, and HDMI), according to actual DMI per day: ≤ 26 kg (n=27); >26 through 28.2 kg (n=28); and >28.2 kg (n=27). The phenotypic Pearson correlations among variables were analyzed, and the GLM procedure was used to test differences between subgroups. The relationships between milk and fat-corrected milk yields and the corresponding gross efficiencies were positive, whereas BW and gross production efficiency were negatively correlated. The marginal production efficiency from DM and energy consumed decreased with increasing DMI. The difference between BW gain as predicted by the National Research Council model (2001) and the present measurements increased with increasing DMI (r=0.68). The average calculated energy balances were 1.38, 2.28, and 4.20 Mcal/d (standard error of the mean=0.64) in the LDMI, MDMI, and HDMI groups, respectively. The marginal efficiency for milk yields from DMI or energy consumed was highest in LDMI, intermediate in MDMI, and lowest in HDMI. The predicted BW gains for the whole study period were 22.9, 37.9, and 75.8 kg for the LDMI, MDMI, and HDMI groups, respectively. The present study demonstrated that marginal production efficiency decreased with increasing feed intake. Because of the close association between production and intake, the principle of diminishing marginal productivity may explain why increasing milk production (and consequently increasing intake) does not always enhance profitability. To maintain high production efficiency in the future, more attention should be given to optimizing rather than maximizing feed intake, a goal that could be achieved by nutritional manipulations that would increase digestibility or by using a diet of denser nutrients that would provide all nutritional requirements from lower intake. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Dietary Factors Modulate Colonic Tumorigenesis Through the Interaction of Gut Microbiota and Host Chloride Channels.

PubMed

Zhang, Yong; Kang, Chao; Wang, Xiao-Lan; Zhou, Min; Chen, Meng-Ting; Zhu, Xiao-Hui; Liu, Kai; Wang, Bin; Zhang, Qian-Yong; Zhu, Jun-Dong; Mi, Man-Tian

2018-03-01

In recent decades, the association among diet, gut microbiota, and the risk of colorectal cancer (CRC) has been established. Gut microbiota and associated metabolites, such as bile acids and butyrate, are now known to play a key role in CRC development. The aim of this study is to identify that the progression to CRC is influenced by cholic acid, sodium butyrate, a high-fat diet, or different dose of dihydromyricetin (DMY) interacted with gut microbiota. An AOM/DSS (azoxymethan/dextran sodium sulfate) model is established to study the gut microbiota compsition before and after tumor formation during colitis-induced tumorigenesis. All above dietary factors profoundly influence the composition of gut microbiota and host colonic tumorigenesis. In addition, mice with DMY-modified initial microbiota display different degrees of chemically induced tumorigenesis. Mechanism analysis reveals that gut microbiota-associated chloride channels participated in colon tumorigenesis. Gut microbiota changes occur in the hyperproliferative stage before tumor formation. Gut microbiota and host chloride channels, both of which are regulated by dietary factors, are associated with CRC development. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Why do you dance? Development of the Dance Motivation Inventory (DMI).

PubMed

Maraz, Aniko; Király, Orsolya; Urbán, Róbert; Griffiths, Mark D; Demetrovics, Zsolt

2015-01-01

Dancing is a popular form of physical exercise and studies have show that dancing can decrease anxiety, increase self-esteem, and improve psychological wellbeing. The aim of the current study was to explore the motivational basis of recreational social dancing and develop a new psychometric instrument to assess dancing motivation. The sample comprised 447 salsa and/or ballroom dancers (68% female; mean age 32.8 years) who completed an online survey. Eight motivational factors were identified via exploratory factor analysis and comprise a new Dance Motivation Inventory: Fitness, Mood Enhancement, Intimacy, Socialising, Trance, Mastery, Self-confidence and Escapism. Mood Enhancement was the strongest motivational factor for both males and females, although motives differed according to gender. Dancing intensity was predicted by three motivational factors: Mood Enhancement, Socialising, and Escapism. The eight dimensions identified cover possible motives for social recreational dancing, and the DMI proved to be a suitable measurement tool to assess these motives. The explored motives such as Mood Enhancement, Socialising and Escapism appear to be similar to those identified in other forms of behaviour such as drinking alcohol, exercise, gambling, and gaming.

Why Do You Dance? Development of the Dance Motivation Inventory (DMI)

PubMed Central

Maraz, Aniko; Király, Orsolya; Urbán, Róbert; Griffiths, Mark D.; Demetrovics, Zsolt

2015-01-01

Dancing is a popular form of physical exercise and studies have show that dancing can decrease anxiety, increase self-esteem, and improve psychological wellbeing. The aim of the current study was to explore the motivational basis of recreational social dancing and develop a new psychometric instrument to assess dancing motivation. The sample comprised 447 salsa and/or ballroom dancers (68% female; mean age 32.8 years) who completed an online survey. Eight motivational factors were identified via exploratory factor analysis and comprise a new Dance Motivation Inventory: Fitness, Mood Enhancement, Intimacy, Socialising, Trance, Mastery, Self-confidence and Escapism. Mood Enhancement was the strongest motivational factor for both males and females, although motives differed according to gender. Dancing intensity was predicted by three motivational factors: Mood Enhancement, Socialising, and Escapism. The eight dimensions identified cover possible motives for social recreational dancing, and the DMI proved to be a suitable measurement tool to assess these motives. The explored motives such as Mood Enhancement, Socialising and Escapism appear to be similar to those identified in other forms of behaviour such as drinking alcohol, exercise, gambling, and gaming. PMID:25803301

Cold blast furnace syndrome: a new source of toxic inhalation by nitrogen oxides.

PubMed

Tague, I; Llewellin, P; Burton, K; Buchan, R; Yates, D H

2004-05-01

To describe a new toxic inhalation syndrome in blast furnace workers. Fourteen workers developed acute respiratory symptoms shortly after exposure to "air blast" from blast furnace tuyeres. These included chest tightness, dyspnoea, rigors, and diaphoresis. Chest radiographs showed pulmonary infiltrates, and lung function a restrictive abnormality. This report includes a description of clinical features of the affected workers and elucidation of the probable cause of the outbreak. Clinical features and occupational hygiene measurements suggested the most likely cause was inhalation of nitrogen oxides at high pressure and temperature. While the task could not be eliminated, engineering controls were implemented to control the hazard. No further cases have occurred. "Cold blast furnace syndrome" represents a previously undescribed hazard of blast furnace work, probably due to inhalation of nitrogen oxides. It should be considered in the differential diagnosis of acute toxic inhalational injuries in blast furnace workers.

Using SPL (Spent Pot-Lining) as an Alternative Fuel in Metallurgical Furnaces

NASA Astrophysics Data System (ADS)

Gao, Lei; Mostaghel, Sina; Ray, Shamik; Chattopadyay, Kinnor

2016-09-01

Replacing coke (coal) in a metallurgical furnace with other alternative fuels is beneficial for process economics and environmental friendliness. Coal injection is a common practice in blast furnace ironmaking, and spent pot-lining (SPL) was conceptualized as an alternative to coal. SPL is a resourceful waste from primary Aluminum production, with high carbon value. Equilibrium thermodynamics was used to calculate the energy content of SPL, and the compositional changes during SPL combustion. In order to capture the kinetics and mass transfer aspects, a blast furnace tuyere region CFD model was developed. The results of SPL combustion were compared with standard PCI coals, which are commonly used in blast furnaces. The CFD model was validated with experimental results for standard high volatile coals.

Cupola Furnace Computer Process Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seymour Katz

2004-12-31

The cupola furnace generates more than 50% of the liquid iron used to produce the 9+ million tons of castings annually. The cupola converts iron and steel into cast iron. The main advantages of the cupola furnace are lower energy costs than those of competing furnaces (electric) and the ability to melt less expensive metallic scrap than the competing furnaces. However the chemical and physical processes that take place in the cupola furnace are highly complex making it difficult to operate the furnace in optimal fashion. The results are low energy efficiency and poor recovery of important and expensive alloymore » elements due to oxidation. Between 1990 and 2004 under the auspices of the Department of Energy, the American Foundry Society and General Motors Corp. a computer simulation of the cupola furnace was developed that accurately describes the complex behavior of the furnace. When provided with the furnace input conditions the model provides accurate values of the output conditions in a matter of seconds. It also provides key diagnostics. Using clues from the diagnostics a trained specialist can infer changes in the operation that will move the system toward higher efficiency. Repeating the process in an iterative fashion leads to near optimum operating conditions with just a few iterations. More advanced uses of the program have been examined. The program is currently being combined with an ''Expert System'' to permit optimization in real time. The program has been combined with ''neural network'' programs to affect very easy scanning of a wide range of furnace operation. Rudimentary efforts were successfully made to operate the furnace using a computer. References to these more advanced systems will be found in the ''Cupola Handbook''. Chapter 27, American Foundry Society, Des Plaines, IL (1999).« less

Reduce Air Infiltration in Furnaces (English/Chinese) (Fact Sheet) (in Chinese; English)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

Chinese translation of the Reduce Air Infiltration in Furnaces fact sheet. Provides suggestions on how to improve furnace energy efficiency. Fuel-fired furnaces discharge combustion products through a stack or a chimney. Hot furnace gases are less dense and more buoyant than ambient air, so they rise, creating a differential pressure between the top and the bottom of the furnace. This differential, known as thermal head, is the source of a natural draft or negative pressure in furnaces and boilers. A well-designed furnace (or boiler) is built to avoid air leakage into the furnace or leakage of flue gases from themore » furnace to the ambient. However, with time, most furnaces develop cracks or openings around doors, joints, and hearth seals. These openings (leaks) usually appear small compared with the overall dimensions of the furnace, so they are often ignored. The negative pressure created by the natural draft (or use of an induced-draft fan) in a furnace draws cold air through the openings (leaks) and into the furnace. The cold air becomes heated to the furnace exhaust gas temperature and then exits through the flue system, wasting valuable fuel. It might also cause excessive oxidation of metals or other materials in the furnaces. The heat loss due to cold air leakage resulting from the natural draft can be estimated if you know four major parameters: (1) The furnace or flue gas temperature; (2) The vertical distance H between the opening (leak) and the point where the exhaust gases leave the furnace and its flue system (if the leak is along a vertical surface, H will be an average value); (3) The area of the leak, in square inches; and (4) The amount of operating time the furnace spends at negative pressure. Secondary parameters that affect the amount of air leakage include these: (1) The furnace firing rate; (2) The flue gas velocity through the stack or the stack cross-section area; (3) The burner operating conditions (e.g., excess air, combustion air temperature, and so on). For furnaces or boilers using an induced-draft (ID) fan, the furnace negative pressure depends on the fan performance and frictional losses between the fan inlet and the point of air leakage. In most cases, it would be necessary to measure or estimate negative pressure at the opening. The amount of air leakage, the heat lost in flue gases, and their effects on increased furnace or boiler fuel consumption can be calculated by using the equations and graphs given in Industrial Furnaces (see W. Trinks et al., below). Note that the actual heat input required to compensate for the heat loss in flue gases due to air leakage would be greater than the heat contained in the air leakage because of the effect of available heat in the furnace. For a high-temperature furnace that is not maintained properly, the fuel consumption increase due to air leakage can be as high as 10% of the fuel input.« less

JPRS Report, Science and Technology, Europe.

DTIC Science & Technology

1991-02-15

VIDP furnace is a further development of the conventional vacuum induction melter (VIM). It has an independent smelting and processing unit, to...which various casting systems can be linked according to the modular principle. Unlike the conventional vacuum induction melter, the VIDP furnace does... induction coil and the crucible. The furnace body can be extracted for relining or replacement with another, ready-lined, fur- nace body. This

Inclusion of calcium hydroxide-treated corn stover as a partial forage replacement in diets for lactating dairy cows.

PubMed

Casperson, Brittany A; Wertz-Lutz, Aimee E; Dunn, Jim L; Donkin, Shawn S

2018-03-01

Chemical treatment may improve the nutritional value of corn crop residues, commonly referred to as corn stover, and the potential use of this feed resource for ruminants, including lactating dairy cows. The objective of this study was to determine the effect of prestorage chopping, hydration, and treatment of corn stover with Ca(OH) 2 on the feeding value for milk production, milk composition, and dry matter intake (DMI). Multiparous mid-lactation Holstein cows (n = 30) were stratified by parity and milk production and randomly assigned to 1 of 3 diets. Corn stover was chopped, hydrated, and treated with 6% Ca(OH) 2 (as-fed basis) and stored in horizontal silo bags. Cows received a control (CON) total mixed ration (TMR) or a TMR in which a mixture of treated corn stover and distillers grains replaced either alfalfa haylage (AHsub) or alfalfa haylage and an additional portion of corn silage (AH+CSsub). Treated corn stover was fed in a TMR at 0, 15, and 30% of the diet DM for the CON, AHsub, and AH+CSsub diets, respectively. Cows were individually fed in tiestalls for 10 wk. Milk production was not altered by treatment. Compared with the CON diet, DMI was reduced when the AHsub diet was fed and tended to be reduced when cows were fed the AH+CSsub diet (25.9, 22.7, and 23.1 ± 0.88 kg/d for CON, AHsub, and AH+CSsub diets, respectively). Energy-corrected milk production per unit of DMI (kg/kg) tended to increase with treated corn stover feeding. Milk composition, energy-corrected milk production, and energy-corrected milk per unit of DMI (kg/kg) were not different among treatments for the 10-wk feeding period. Cows fed the AHsub and AH+CSsub diets had consistent DMI over the 10-wk treatment period, whereas DMI for cows fed the CON diet increased slightly over time. Milk production was not affected by the duration of feeding. These data indicate that corn stover processing, prestorage hydration, and treatment with calcium hydroxide can serve as an alternative to traditional haycrop and corn silage in diets fed to mid-lactation dairy cows. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The technological raw material heating furnaces operation efficiency improving issue

NASA Astrophysics Data System (ADS)

Paramonov, A. M.

2017-08-01

The issue of fuel oil applying efficiency improving in the technological raw material heating furnaces by means of its combustion intensification is considered in the paper. The technical and economic optimization problem of the fuel oil heating before combustion is solved. The fuel oil heating optimal temperature defining method and algorithm analytically considering the correlation of thermal, operating parameters and discounted costs for the heating furnace were developed. The obtained optimization functionality provides the heating furnace appropriate thermal indices achievement at minimum discounted costs. The carried out research results prove the expediency of the proposed solutions using.

Current induced domain wall motion and tilting in Pt/Co/Ta structures with perpendicular magnetic anisotropy in the presence of the Dyzaloshinskii–Moriya interaction

NASA Astrophysics Data System (ADS)

Yun, Jijun; Li, Dong; Cui, Baoshan; Guo, Xiaobin; Wu, Kai; Zhang, Xu; Wang, Yupei; Mao, Jian; Zuo, Yalu; Xi, Li

2018-04-01

Current induced domain wall motion (CIDWM) was studied in Pt/Co/Ta structures with perpendicular magnetic anisotropy and the Dyzaloshinskii–Moriya interaction (DMI) by the spin-orbit torque (SOT). We measured the strength of DMI and SOT efficiency in Pt/Co/Ta with the variation of the thickness of Ta using a current induced hysteresis loop shift method. The results indicate that the DMI stabilizes a chiral Néel-type domain wall (DW), and the DW motion can be driven by the enhanced large SOT generated from Pt and Ta with opposite signs of spin Hall angle in Pt/Co/Ta stacks. The CIDWM velocity, which is 104 times larger than the field driven DW velocity, obeys a creep law, and reaches around tens of meters per second with current density of ~106 A cm‑2. We also found that the Joule heating accompanied with current also accelerates the DW motion. Meanwhile, a domain wall tilting was observed, which increases with current density increasing. These results can be explained by the spin Hall effect generated from both heavy metals Pt and Ta, inherent DMI, and the current accompanying Joule heating effect. Our results could provide some new designing prospects to move multiple DWs by SOT for achieving racetrack memories.

Enhanced interfacial Dzyaloshinskii-Moriya interaction and isolated skyrmions in the inversion-symmetry-broken Ru/Co/W/Ru films

NASA Astrophysics Data System (ADS)

Samardak, Alexander; Kolesnikov, Alexander; Stebliy, Maksim; Chebotkevich, Ludmila; Sadovnikov, Alexandr; Nikitov, Sergei; Talapatra, Abhishek; Mohanty, Jyoti; Ognev, Alexey

2018-05-01

An enhancement of the spin-orbit effects arising on an interface between a ferromagnet (FM) and a heavy metal (HM) is possible through the strong breaking of the structural inversion symmetry in the layered films. Here, we show that an introduction of an ultrathin W interlayer between Co and Ru in Ru/Co/Ru films enables to preserve perpendicular magnetic anisotropy (PMA) and simultaneously induce a large interfacial Dzyaloshinskii-Moriya interaction (iDMI). The study of the spin-wave propagation in the Damon-Eshbach geometry by Brillouin light scattering spectroscopy reveals the drastic increase in the iDMI value with the increase in W thickness (tW). The maximum iDMI of -3.1 erg/cm2 is observed for tW = 0.24 nm, which is 10 times larger than for the quasi-symmetrical Ru/Co/Ru films. We demonstrate the evidence of the spontaneous field-driven nucleation of isolated skyrmions supported by micromagnetic simulations. Magnetic force microscopy measurements reveal the existence of sub-100-nm skyrmions in the zero magnetic field. The ability to simultaneously control the strength of PMA and iDMI in quasi-symmetrical HM/FM/HM trilayer systems through the interface engineered inversion asymmetry at the nanoscale excites new fundamental and practical interest in ultrathin ferromagnets, which are a potential host for stable magnetic skyrmions.

Within- and between-orchard variability in the sensitivity of Venturia inaequalis to myclobutanil, a DMI fungicide, in the UK.

PubMed

Gao, Liqiang; Berrie, Angela; Yang, Jiarong; Xu, Xiangming

2009-11-01

Myclobutanil, a demethylation inhibitor (DMI) fungicide, is an important fungicide for controlling apple scab and powdery mildew. Overuse of this fungicide has led to establishment of scab isolates with reduced sensitivity to this fungicide in several countries. Experiments were conducted to determine the sensitivity of the causal agent of apple scab, Venturia inaequalis (Cooke) Winter, to myclobutanil in the UK, in order to assess whether there is a relationship between fungal insensitivity and the number of DMI applications, and establishing whether fungal sensitivity varied greatly within an orchard. Reduced sensitivity of V. inaequalis to myclobutanil was positively related linearly to the number of DMI applications. ED(50) values ranged from 0.028 to 1.017 mg L(-1) (average = 0.292) for the baseline population, whereas isolates from two other orchards had much greater ED(50) values, ranging from 0.085 to 5.213 mg L(-1) (average = 1.852). There was significant variation in fungal sensitivity to myclobutanil among fungal isolates from different locations within a single orchard. Spatial spread of insensitive isolates of V. inaequalis to myclobutanil is likely to be limited in distance. Conidia may be an important source of primary inoculum. Myclobutanil should still be effective for most field isolates, but its use should be strategically integrated with other groups of fungicides. (c) 2009 Society of Chemical Industry.

Lipid raft integrity affects GABAA receptor, but not NMDA receptor modulation by psychopharmacological compounds.

PubMed

Nothdurfter, Caroline; Tanasic, Sascha; Di Benedetto, Barbara; Uhr, Manfred; Wagner, Eva-Maria; Gilling, Kate E; Parsons, Chris G; Rein, Theo; Holsboer, Florian; Rupprecht, Rainer; Rammes, Gerhard

2013-07-01

Lipid rafts have been shown to play an important role for G-protein mediated signal transduction and the function of ligand-gated ion channels including their modulation by psychopharmacological compounds. In this study, we investigated the functional significance of the membrane distribution of NMDA and GABAA receptor subunits in relation to the accumulation of the tricyclic antidepressant desipramine (DMI) and the benzodiazepine diazepam (Diaz). In the presence of Triton X-100, which allowed proper separation of the lipid raft marker proteins caveolin-1 and flotillin-1 from the transferrin receptor, all receptor subunits were shifted to the non-raft fractions. In contrast, under detergent-free conditions, NMDA and GABAA receptor subunits were detected both in raft and non-raft fractions. Diaz was enriched in non-raft fractions without Triton X-100 in contrast to DMI, which preferentially accumulated in lipid rafts. Impairment of lipid raft integrity by methyl-β-cyclodextrine (MβCD)-induced cholesterol depletion did not change the inhibitory effect of DMI at the NMDA receptor, whereas it enhanced the potentiating effect of Diaz at the GABAA receptor at non-saturating concentrations of GABA. These results support the hypothesis that the interaction of benzodiazepines with the GABAA receptor likely occurs outside of lipid rafts while the antidepressant DMI acts on ionotropic receptors both within and outside these membrane microdomains.

Automated information system for analysis and prediction of production situations in blast furnace plant

NASA Astrophysics Data System (ADS)

Lavrov, V. V.; Spirin, N. A.

2016-09-01

Advances in modern science and technology are inherently connected with the development, implementation, and widespread use of computer systems based on mathematical modeling. Algorithms and computer systems are gaining practical significance solving a range of process tasks in metallurgy of MES-level (Manufacturing Execution Systems - systems controlling industrial process) of modern automated information systems at the largest iron and steel enterprises in Russia. This fact determines the necessity to develop information-modeling systems based on mathematical models that will take into account the physics of the process, the basics of heat and mass exchange, the laws of energy conservation, and also the peculiarities of the impact of technological and standard characteristics of raw materials on the manufacturing process data. Special attention in this set of operations for metallurgic production is devoted to blast-furnace production, as it consumes the greatest amount of energy, up to 50% of the fuel used in ferrous metallurgy. The paper deals with the requirements, structure and architecture of BF Process Engineer's Automated Workstation (AWS), a computer decision support system of MES Level implemented in the ICS of the Blast Furnace Plant at Magnitogorsk Iron and Steel Works. It presents a brief description of main model subsystems as well as assumptions made in the process of mathematical modelling. Application of the developed system allows the engineering and process staff to analyze online production situations in the blast furnace plant, to solve a number of process tasks related to control of heat, gas dynamics and slag conditions of blast-furnace smelting as well as to calculate the optimal composition of blast-furnace slag, which eventually results in increasing technical and economic performance of blast-furnace production.

Space Station Furnace Facility. Experiment/Facility Requirements Document (E/FRD), volume 2, appendix 5

NASA Technical Reports Server (NTRS)

Kephart, Nancy

1992-01-01

The function of the Space Station Furnace Facility (SSFF) is to support materials research into the crystal growth and solidification processes of electronic and photonic materials, metals and alloys, and glasses and ceramics. To support this broad base of research requirements, the SSFF will employ a variety of furnace modules operated, regulated, and supported by a core of common subsystems. Furnace modules may be reconfigured or specifically developed to provide unique solidifcation conditions for each set of experiments. The SSFF modular approach permits the addition of new or scaled-up furnace modules to support the evolution of the facility as new science requirements are identified. The SSFF Core is of modular design to permit augmentation for enhanced capabilities. The fully integrated configuration of the SSFF will consist of three racks with the capability of supporting up to two furnace modules per rack. The initial configuration of the SSFF will consist of two of the three racks and one furnace module. This Experiment/Facility Requirements Document (E/FRD) describes the integrated facility requirements for the Space Station Freedom (SSF) Integrated Configuration-1 (IC1) mission. The IC1 SSFF will consist of two racks: the Core Rack, with the centralized subsystem equipment, and the Experiment Rack-1, with Furnace Module-1 and the distributed subsystem equipment to support the furnace.

Preliminary control system design and analysis for the Space Station Furnace Facility thermal control system

NASA Technical Reports Server (NTRS)

Jackson, M. E.

1995-01-01

This report presents the Space Station Furnace Facility (SSFF) thermal control system (TCS) preliminary control system design and analysis. The SSFF provides the necessary core systems to operate various materials processing furnaces. The TCS is defined as one of the core systems, and its function is to collect excess heat from furnaces and to provide precise cold temperature control of components and of certain furnace zones. Physical interconnection of parallel thermal control subsystems through a common pump implies the description of the TCS by coupled nonlinear differential equations in pressure and flow. This report formulates the system equations and develops the controllers that cause the interconnected subsystems to satisfy flow rate tracking requirements. Extensive digital simulation results are presented to show the flow rate tracking performance.

MUZO flight experience with the programmable multizone furnace

NASA Technical Reports Server (NTRS)

Lockowandt, Christian; Loth, Kenneth

1993-01-01

The Multi-Zone (MUZO) furnace has been developed for growing germanium (Ge) crystals under microgravity in a Get Away Special (GAS) payload. The MUZO furnace was launched with STS-47 Endeavour in September 1992. The payload worked as planned during the flight and a Ge sample was successfully processed. The experiment has given valuable scientific information. The design and functionality of the payload together with flight experience is reported.

Feeding value of whole raw soya beans as a protein supplement for beef cattle consuming low-quality forages.

PubMed

Arelovich, H M; Lagrange, S; Torre, R; Martinez, M F; Laborde, H E

2018-02-01

Experiments (Exp) I and II were conducted to compare raw whole soya beans (WSB), roasted (rWSB) or other protein sources as supplements of low-quality forages fed ad libitum to beef cattle, upon DM intake (DMI), ruminal and blood parameters, and animal performance. Exp I: treatments for wheat straw fed to four ruminally cannulated steers were (i) Control-WS: no supplement; (ii) WSB-WS: whole soya beans; (iii) rWSB-WS: roasted WSB; and (iv) SBM-WS: soybean meal-wheat midds mixture; all fed at 1.4 kg DM/day. Exp II: 12 steers grazed deferred grain sorghum (DS) receiving these treatments: (i) Control-DS: no supplement; (ii) WSB-DS: 1.26 kg DM/day whole soya beans; and (iii) SFM-DS: 1.35 kg DM/day of sunflower meal. In Exp I, WS DMI resulted 47, 52 and 41% greater for WSB-WS, rWSB-WS and SBM-WS, respectively, than Control-WS (p < .05). In Exp II, the DMI of DS was unaffected by supplementation; a substitution of DS by supplement was found for WSB-DS (p < .05); however, total diet and digestible DMI increased with supplementation (p < .05). Rumen pH in Exp I remained unaffected by supplementation, but N-NH 3 as well as blood urea-N in Exp II increased (p < .05). In Exp II, average daily weight gains improved similarly with both supplements compared with Control-DS. Additionally, feed-to-gain ratio decreased (p < .05), being lower for WSB-DS (8.3) vs. SFM-DS (9.9). Roasting effects of WSB as a supplement for low-quality forages were not detected, and all protein sources increased total diet DMI and forage utilization. Only moderate cattle weight gains could be expected for unsupplemented DS. © 2017 Blackwell Verlag GmbH.

Cloning and expression analysis of the ATP-binding cassette transporter gene MFABC1 and the alternative oxidase gene MfAOX1 from Monilinia fructicola.

PubMed

Schnabel, Guido; Dait, Qun; Paradkar, Manjiri R

2003-10-01

Brown rot, caused by Moniliniafructicola (G Wint) Honey, is a serious disease of peach in all commercial peach production areas in the USA, including South Carolina where it has been primarily controlled by pre-harvest application of 14-alpha demethylation (DMI) fungicides for more than 15 years. Recently, the Qo fungicide azoxystrobin was registered for brown rot control and is currently being investigated for its potential as a DMI fungicide rotation partner because of its different mode of action. In an effort to investigate molecular mechanisms of DMI and Qo fungicide resistance in M fructicola, the ABC transporter gene MfABC1 and the alternative oxidase gene MfAOX1 were cloned to study their potential role in conferring fungicide resistance. The MfABC1 gene was 4380 bp in length and contained one intron of 71 bp. The gene revealed high amino acid homologies with atrB from Aspergillus nidulans (Eidam) Winter, an ABC transporter conferring resistance to many fungicides, including DMI fungicides. MfABC1 gene expression was induced after myclobutanil and propiconazole treatment in isolates with low sensitivity to the same fungicides, and in an isolate with high sensitivity to propiconazole. The results suggest that the MfABC1 gene may be a DMI fungicide resistance determinant in M fructicola. The alternative oxidase gene MfAOX1 from M fructicola was cloned and gene expression was analyzed. The MfAOX1 gene was 1077 bp in length and contained two introns of 54 and 67 bp. The amino acid sequence was 63.8, 63.8 and 57.7% identical to alternative oxidases from Venturia inaequalis (Cooke) Winter, Aspergillus niger van Teighem and A nidulans, respectively. MfAOX1 expression in some but not all M fructicola isolates was induced in mycelia treated with azoxystrobin. Azoxystrobin at 2 microg ml(-1) significantly induced MfAOX1 expression in isolates with low MfAOX1 constitutive expression levels.

Modelling digestive constraints in non-ruminant and ruminant foregut-fermenting mammals.

PubMed

Munn, Adam J; Streich, W Jürgen; Hummel, Jürgen; Clauss, Marcus

2008-09-01

It has been suggested that large foregut-fermenting marsupial herbivores, the kangaroos and their relatives, may be less constrained by food intake limitations as compared with ruminants, due mainly to differences in their digestive morphology and management of ingesta particles through the gut. In particular, as the quality of forage declines with increasing contents of plant fibre (cellulose, hemicelluloses and lignin; measured as neutral-detergent fibre, NDF), the tubiform foregut of kangaroos may allow these animals to maintain food intakes more so than ruminants like sheep, which appear to be limited by fibrous bulk filling the foregut and truncating further ingestion. Using available data on dry matter intake (DMI, g kg(-0.75) d(-1)), ingesta mean retention time (MRT, h), and apparent digestibility, we modelled digestible dry matter intake (DDMI) and digestible energy intake (DEI) by ruminant sheep (Ovis aries) and by the largest marsupial herbivore, the red kangaroo (Macropus rufus). Sheep achieved higher MRTs on similar DMIs, and hence sheep achieved higher DDMIs for any given level of DMI as compared with kangaroos. Interestingly, MRT declined in response to increasing DMI in a similar pattern for both species, and the association between DMI and plant NDF contents did not support the hypothesis that kangaroos are less affected by increasing fibre relative to sheep. However, when DEI was modelled according to DDMIs and dietary energy contents, we show that the kangaroos could meet their daily maintenance energy requirements (MER) at lower levels of DMI and on diets with higher fibre contents compared with sheep, due largely to the kangaroos' lower absolute maintenance and basal energy metabolisms compared with eutherians. These results suggest that differences in the metabolic set-point of different species can have profound effects on their nutritional niche, even when their digestive constraints are similar, as was the case for these ruminant and non-ruminant foregut fermenters.

Production responses of Holstein dairy cows when fed supplemental fat containing saturated free fatty acids: a meta-analysis

PubMed Central

Hu, Wenping; Boerman, Jacquelyn P.; Aldrich, James M.

2017-01-01

Objective A meta-analysis was conducted to evaluate the effects of supplemental fat containing saturated free fatty acids (FA) on milk performance of Holstein dairy cows. Methods A database was developed from 21 studies published between 1991 and 2016 that included 502 dairy cows and a total of 29 to 30 comparisons between dietary treatment and control without fat supplementation. Only saturated free FA (>80% of total FA) was considered as the supplemental fat. Concentration of the supplemental fat was not higher than 3.5% of diet dry matter (DM). Dairy cows were offered total mixed ration, and fed individually. Statistical analysis was conducted using random- or mixed-effects models with Metafor package in R. Results Sub-group analysis showed that there were no differences in studies between randomized block design and Latin square/crossover design for dry matter intake (DMI) and milk production responses to the supplemental fat (all response variables, p≥0.344). The supplemental fat across all studies improved milk yield, milk fat concentration and yield, and milk protein yield by 1.684 kg/d (p<0.001), 0.095 percent unit (p = 0.003), 0.072 kg/d (p<0.001), and 0.036 kg/d (p<0.001), respectively, but tended to decrease milk protein concentration (mean difference = −0.022 percent unit; p = 0.063) while DMI (mean difference = 0.061 kg/d; p = 0.768) remained unchanged. The assessment of heterogeneity suggested that no substantial heterogeneity occurred among all studies for DMI and milk production responses to the supplemental fat (all response variables, I2≤24.1%; p≥0.166). Conclusion The effects of saturated free FA were quantitatively evaluated. Higher milk production and yields of milk fat and protein, with DMI remaining unchanged, indicated that saturated free FA, supplemented at ≤3.5% dietary DM from commercially available fat sources, likely improved the efficiency of milk production. Nevertheless, more studies are needed to assess the variation of production responses to different saturated free FA, either C16:0 or C18:0 alone, or in combination with potentially optimal ratio, when supplemented in dairy cow diets. PMID:28183166

Development and Evaluation of a Virtual Campus on Second Life: The Case of SecondDMI

ERIC Educational Resources Information Center

De Lucia, Andrea; Francese, Rita; Passero, Ignazio; Tortora, Genoveffa

2009-01-01

Video games and new communication metaphors are quickly changing today's young people habits. Considering the actual e-learning scenarios, embedded in a fully technological enabled environment it is crucial to take advantage of this kind of capabilities to let learning process gain best results. This paper presents a virtual campus created using…

Space Station Furnace Facility Preliminary Project Implementation Plan (PIP). Volume 2, Appendix 2

NASA Technical Reports Server (NTRS)

Perkey, John K.

1992-01-01

The Space Station Furnace Facility (SSFF) is an advanced facility for materials research in the microgravity environment of the Space Station Freedom and will consist of Core equipment and various sets of Furnace Module (FM) equipment in a three-rack configuration. This Project Implementation Plan (PIP) document was developed to satisfy the requirements of Data Requirement Number 4 for the SSFF study (Phase B). This PIP shall address the planning of the activities required to perform the detailed design and development of the SSFF for the Phase C/D portion of this contract.

[The electric furnace of Henri Moissan at one hundred years: connection with the electric furnace, the solar furnace, the plasma furnace?].

PubMed

Royère, C

1999-03-01

The trace of Henri Moissan's pioneer work 100 years ago is clearly evidenced by an overview of achievements in high temperature devices; 1987: "Le four électrique" by Henri Moissan; 1948-1952: "High temperature heating in a cavity rotary kiln using focusing of solar radiation" by Félix Trombe; 1962: "The cavity rotary kiln using focused solar radiation jointly with a plasma gun" by Marc Foëx; 1970: "The rotary kiln with two plasma guns and arc transfer" by Marc Foëx; 1984: "The plasma furnace" by Electricité de France (EDF) at Renardières; 1997: "The plasma furnace" by the Atomic Energy Center (CEA) at Cadarache, the VULCANO program. The first part of this contribution is devoted to Henri Moissan. Re-reading his early book on the electric furnace, especially the first chapter and the sections on silica, carbon vapor and experiments performed in casting molten metal--the conclusions are outstanding--provides modern readers with an amazing insight into future developments. The last two parts are devoted to Félix Trombe and Marc Foëx, tracing the evolution of high temperature cavity processus leading to the solar furnace and the present day plasma furnace at the CEA. Focus is placed on research conducted by the French National Center for Scientific Research (CNRS) with the solar and plasma furnaces at Odeillo. The relationships with Henri Moissan's early work are amazing, offering a well deserved homage to this pioneer researcher.

New algorithm for controlling electric arc furnaces using their vibrational and acoustic characteristics

NASA Astrophysics Data System (ADS)

Cherednichenko, V. S.; Bikeev, R. A.; Serikov, V. A.; Rechkalov, A. V.; Cherednichenko, A. V.

2016-12-01

The processes occurring in arc discharges are analyzed as the sources of acoustic radiation in an electric arc furnace (EAF). Acoustic vibrations are shown to transform into mechanical vibrations in the furnace laboratory. The shielding of the acoustic energy fluxes onto water-cooled wall panels by a charge is experimentally studied. It is shown that the rate of charge melting and the depth of submergence of arc discharges in the slag and metal melt can be monitored by measuring the vibrational characteristics of furnaces and using them in a universal industrial process-control system, which was developed for EAFs.

Microgravity

NASA Image and Video Library

2001-06-05

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Here the transparent furnace is extracted for servicing. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Association of SNP of neuropeptide Y, leptin, and IGF-1 genes with residual feed intake in confinement and under grazing condition in Angus cattle.

PubMed

Trujillo, A I; Casal, A; Peñagaricano, F; Carriquiry, M; Chilibroste, P

2013-09-01

In this study we quantify and compare the phenotypic variation in residual feed intake (RFI) in 2 groups of Angus female calves: one carrying simultaneously putative favorable allelic variants (SNP) of neuropeptide Y, leptin, and IGF-1 genes (VAL group) and another devoid of such alleles (CON group). We performed 2 sequential trials: under confinement feeding a high-concentrate diet and under grazing condition. In confinement, 38 purebred Angus female calves [mean age and BW of 247 d (SD = 15) and 186 kg (SD = 33.2), respectively] were offered a total mixed ration diet (60:40 concentrate: alfalfa hay, as fed) ad libitum during 57 d. Dry matter intake was estimated from the difference between offered and refused feed; BW was recorded every 2 wk. Under grazing, 12 heifers from each group were ranked by BW and RFI and randomly assigned to 4 pasture paddocks. Heifers were continuously stocked at high-quality, high-herbage-mass mixed pasture. Herbage DMI was determined using the n-alkane technique. Different models were used to determine RFI: models that use phenotypic data [RFI as described by Koch et al. (1963; RFIK) and RFI as described by ME (RFIME)] and models that use standards feeding data [RFI estimated by Fan et al. (1995; RFIF) and RFI in which the expected DMI was derived from equations in Standing Committee on Agriculture (1990; RFISCA)]. Least squares mean values (SE) of DMI (kg/d), metabolizable energy intake (MEI; Mcal/d), ADG (kg), RFIK (kg DM/d), and feed conversion ratio (FCR; kg DMI/kg ADG) for VAL and CON genotype groups were 6.65 and 6.89 (0.49), 16.7 and 17.4 (1.44), 1.24 and 1.24 (0.03), -0.11 and 0.11 (0.09), and 5.8 and 5.8 (0.14), respectively, in the confinement trial. In the grazing trial least squares mean values (SE) of herbage DMI (kg/d), ADG (kg), MEI (Mcal/d), RFIK, and FCR of VAL and CON groups were 8.76 and 10.93 (0.71), 1.4 and 1.37 (0.05), 25.5 and 31.7 (2.09), -1.02 and 1.02 (0.42), and 6.41 and 6.96 (0.46), respectively. Genotyped groups tended to differ in DMI (P = 0.10), in MEI (P = 0.06), and in RFIK (P = 0.10), differed in RFIF (P = 0.010), and did not differ in ADG or FCR during confinement. During grazing, genotyped groups differed in DMI (P = 0.005), in MEI (P = 0.006), and in RFIK (P = 0.002) but did not differ in ADG and FCR. Our results demonstrate a strong association between these 3 SNP and RFI when animals were grazing on a high-quality, high-availability pasture, whereas a weak effect was observed under confinement.

Using simulation models to predict feed intake: phenotypic and genetic relationships between observed and predicted values in cattle.

PubMed

Williams, C B; Bennett, G L; Jenkins, T G; Cundiff, L V; Ferrell, C L

2006-06-01

The objectives of this study were to evaluate the accuracy of the Decision Evaluator for the Cattle Industry (DECI) and the Cornell Value Discovery System (CVDS) in predicting individual DMI and to assess the feasibility of using predicted DMI data in genetic evaluations of cattle. Observed individual animal data on the average daily DMI (OFI), ADG, and carcass measurements were obtained from postweaning records of 504 steers from 52 sires (502 with complete data). The experimental data and daily temperature and wind speed data were used as inputs to predict average daily feed DMI (kg) required (feed required; FR) for maintenance, cold stress, and ADG; maintenance and cold stress; ADG; maintenance and ADG; and maintenance alone, with CVDS (CFRmcg, CFRmc, CFRg, CFRmg, and CFRm, respectively) and DECI (DFRmcg, DFRmc, DFRg, DFRmg, and DFRm, respectively). Genetic parameters were estimated by REML using an animal model with age on test as a covariate and with genotype, age of dam, and year as fixed effects. Regression equations for observed on predicted DMI were OFI = 1.27 (SE = 0.27) + 0.83 (SE = 0.04) x CFRmcg [R2 = 0.44, residual SD (s(y.x)) = 0.669 kg/d] and OFI = 1.32 (SE = 0.22) + 0.8 (SE = 0.03) x DFRmcg (R2 = 0.53, s(y.x) = 0.612 kg/d). Heritability of OFI was 0.27 +/- 0.12, and heritabilities ranged from 0.33 +/- 0.12 to 0.41 +/- 0.13 for predicted measures of DMI. Phenotypic and genetic correlations between OFI and CFRmcg, CFRmc, CFRg, CFRmg, CFRm, DFRmcg, DFRmc, DFRg, DFRmg, and DFRm were 0.67, 0.73, 0.41, 0.63, 0.78, 0.73, 0.82, 0.45, 0.77, and 0.86 (P < 0.001 for all phenotypic correlations); and 0.95 +/- 0.07, 0.82 +/- 0.13, 0.89 +/- 0.09, 0.95 +/- 0.07, 0.91 +/- 0.09, 0.96 +/- 0.07, 0.89 +/- 0.09, 0.88 +/- 0.09, 0.96 +/- 0.06, and 0.96 +/- 0.07, respectively. Phenotypic and genetic correlations between CFRmcg and DFRmcg, CFRmc and DFRmc, CFRg and DFRg, CFRmg and DFRmg, and CFRm and DFRm were 0.98, 0.94, 0.99, 0.98, and 0.95 (P < 0.001 for all phenotypic correlations), and 0.99 +/- 0.004, 0.98 +/- 0.017, 0.99 +/- 0.004, 0.99 +/- 0.005, and 0.97 +/- 0.021, respectively. The strong genetic relationships between OFI and CFRmcg, CFRmg, DFRmcg, and DFRmg indicate that these predicted measures of DMI may be used in genetic evaluations and that DM requirements for cold stress may not be needed, thus reducing model complexity. However, high genetic correlations for final weight with OFI, CFRmcg, and DFRmcg suggest that the technology needs to be further evaluated in populations with genetic variance in feed efficiency.

Soybean hull and enzyme inclusion effects on diet digestibility and growth performance in beef steers consuming corn-based diets.

PubMed

Russell, J R; Sexten, W J; Kerley, M S

2016-06-01

A beef feedlot study was conducted to determine the effects of increasing soybean hull (SH) inclusion and enzyme addition on diet digestibility and animal performance. The hypothesis was SH inclusion and enzyme addition would increase fiber digestibility with no negative effect on animal performance. Eight treatments (TRT) were arranged in a 4 × 2 factorial using four diets and two enzyme (ENZ) inclusion rates. The diets were composed primarily of whole shell corn (WSC) with 0%, 7%, 14%, or 28% SH replacing corn. The ENZ was a commercial proprietary mix of , and (Cattlemace, R&D Life Sciences, Menomonie, WI) included in the diets at 0% (S0, S7, S14, S28) or 0.045% DM basis (S0e, S7e, S14e, S28e). Eighty steers (287 ± 31 kg, SD) were stratified by weight and blocked into pens with 1 heavy and 1 light pen per TRT (2 pen/TRT, 5 steers/pen). Steers were fed for 70 d with titanium dioxide included in the diets for the final 15 d. Fecal samples were collected on d 70 to determine diet digestibility. Diets were balanced for AA and RDP requirement based on available ME. Individual DMI was measured using a GrowSafe system. Diet, ENZ, and diet × ENZ effects were analyzed using the MIXED procedure of SAS. Initial BW was applied as a covariate for final BW (FBW), and DMI was included as a covariate for all digestibility measures. The diet × ENZ interaction had no effect on FBW, ADG, DMI, or any digestibility measure ( ≥ 0.11). Steers fed ENZ tended to have greater FBW ( = 0.09) and had numerically greater ADG than steers not fed ENZ. Diet influenced DMI ( < 0.01), as steers fed S7 diets had the greatest DMI ( ≤ 0.3), steers fed S0 diets had the least DMI ( ≤ 0.002), and DMI of steers fed S14 and S28 diets did not differ ( = 0.5). There was a diet × ENZ interaction for G:F ( = 0.02) in which S0, S0e, S14e, and S28e did not differ ( ≥ 0.3) and were greatest ( ≤ 0.05). There was no effect of diet or ENZ on DM, OM, or CP digestibility ( ≥ 0.2). Diet had an effect on NDF and ADF digestibility ( ≤ 0.04) which decreased as SH inclusion increased. The addition of ENZ tended to decrease NDF digestibility ( = 0.08) but had no effect on ADF digestibility ( = 0.8). Fiber digestibility in WSC diets did not improve with SH inclusion or ENZ addition but steers fed diets with 14% to 28% of WSC replaced by SH and the addition of 0.045% ENZ converted feed at the same rate as steers fed WSC diets with no SH.

Simulation on an optimal combustion control strategy for 3-D temperature distributions in tangentially pc-fired utility boiler furnaces.

PubMed

Wang, Xi-fen; Zhou, Huai-chun

2005-01-01

The control of 3-D temperature distribution in a utility boiler furnace is essential for the safe, economic and clean operation of pc-fired furnace with multi-burner system. The development of the visualization of 3-D temperature distributions in pc-fired furnaces makes it possible for a new combustion control strategy directly with the furnace temperature as its goal to improve the control quality for the combustion processes. Studied in this paper is such a new strategy that the whole furnace is divided into several parts in the vertical direction, and the average temperature and its bias from the center in every cross section can be extracted from the visualization results of the 3-D temperature distributions. In the simulation stage, a computational fluid dynamics (CFD) code served to calculate the 3-D temperature distributions in a furnace, then a linear model was set up to relate the features of the temperature distributions with the input of the combustion processes, such as the flow rates of fuel and air fed into the furnaces through all the burners. The adaptive genetic algorithm was adopted to find the optimal combination of the whole input parameters which ensure to form an optimal 3-D temperature field in the furnace desired for the operation of boiler. Simulation results showed that the strategy could soon find the factors making the temperature distribution apart from the optimal state and give correct adjusting suggestions.

Electric-field-induced modification in Dzyaloshinskii-Moriya interaction of Co monolayer on Pt(111)

NASA Astrophysics Data System (ADS)

Nakamura, Kohji; Akiyama, Toru; Ito, Tomonori; Ono, Teruo; Weinert, Michael

Magnetism induced by an external electric field (E-field) has received much attention as a potential approach for controlling magnetism at the nano-scale with the promise of ultra-low energy power consumption. Here, the E-field-induced modification of the Dzyaloshinskii-Moriya interaction (DMI) for a prototypical transition-metal thin layer of a Co monolayer on Pt(111) is investigated by first-principles calculations by using the full-potential linearized augmented plane wave method that treats spin-spiral structures in an E-field. With inclusion of the spin-orbit coupling (SOC) by the second variational method for commensurate spin-spiral structures, the DMI constants were estimated from an asymmetric contribution in the total energy with respect to the spin-spiral wavevector. The results predicted that the DMI is modified by the E-field, but the change is found to be small compared to that in the exchange interaction (a symmetric contribution in the total energy) by a factor of ten.

Anti-ceramidase LCL385 acutely reduces BCL-2 expression in the hippocampus but is not associated with an increase of learned helplessness in rats.

PubMed

Nahas, Ziad; Jiang, Yan; Zeidan, Youssef H; Bielawska, Alicja; Szulc, Zdzislaw; Devane, Lindsay; Kalivas, Peter; Hannun, Yusuf A

2009-01-30

Evidence from in situ studies supports the role of anti-apoptotic factors in the antidepressant responses of certain psychotropics. The availability of anti-ceramidase pro-apoptocic compound (LCL385) provides an opportunity to test in vivo the relation between hippocampal apopotosis and learned helplessness. 40 Sprague-Dawley male rodents underwent an FST after a treatment with LCL385, desipramine (DMI), or placebo (SAL) over 3 days. Behavioral responses, including immobility, swimming and climbing were counted during the 6min test. Western blot labeling was used to detect anti-apoptosis in hippocampus. DMI alone was associated with reduced immobility and increased climbing whereas LCL385 alone showed a decrease in Bcl-2/beta-actin ratio. Direct modulation of Bcl-2 expression in the hippocampus is not associated with learned helplessness in stressed rats. Three-day administration of DMI and LCL385 show divergent effects on behavioral and anti-apoptotic measures.

Space Station Furnace Facility. Volume 2: Summary of technical reports

NASA Technical Reports Server (NTRS)

1992-01-01

The Space Station Furnace Facility (SSFF) is a modular facility for materials research in the microgravity environment of the Space Station Freedom (SSF). The SSFF is designed for crystal growth and solidification research in the fields of electronic and photonic materials, metals and alloys, and glasses and ceramics, and will allow for experimental determination of the role of gravitational forces in the solidification process. The facility will provide a capability for basic scientific research and will evaluate the commercial viability of low-gravity processing of selected technologically important materials. In order to accommodate the furnace modules with the resources required to operate, SSFF developed a design that meets the needs of the wide range of furnaces that are planned for the SSFF. The system design is divided into subsystems which provide the functions of interfacing to the SSF services, conditioning and control for furnace module use, providing the controlled services to the furnace modules, and interfacing to and acquiring data from the furnace modules. The subsystems, described in detail, are as follows: Power Conditioning and Distribution Subsystem; Data Management Subsystem; Software; Gas Distribution Subsystem; Thermal Control Subsystem; and Mechanical Structures Subsystem.

Corn silage from corn treated with foliar fungicide and performance of Holstein cows.

PubMed

Haerr, K J; Lopes, N M; Pereira, M N; Fellows, G M; Cardoso, F C

2015-12-01

Foliar fungicide application to corn plants is used in corn aimed for corn silage in the dairy industry, but questions regarding frequency of application and its effect on corn silage quality and feed conversion when fed to dairy cows remain prevalent. The objective of this study was to evaluate the effects of various foliar fungicide applications to corn on dry matter intake (DMI), milk production, and milk composition when fed to dairy cows. Sixty-four Holstein cows with parity 2.5±1.5, 653±80kg of body weight, and 161±51d in milk were blocked and randomly assigned to 1 of 4 corn silage treatments (total mixed ration with 35% of the dry matter as corn silage). Treatments were as follows: control (CON), corn silage with no applications of foliar fungicide; treatment 1 (1X), corn silage from corn that received 1 application of pyraclostrobin (PYR) foliar fungicide (Headline; BASF Corp.) at corn vegetative stage 5; treatment 2 (2X), corn silage from corn that received the same application as 1X plus another application of a mixture of PYR and metconazole (Headline AMP; BASF Corp.) at corn reproductive stage 1 ("silking"); and treatment 3 (3X), corn silage from corn that received the same applications as 2X as well as a third application of PYR and metconazole at reproductive stage 3 ("milky kernel"). Corn was harvested at about 32% dry matter and 3/4 milk line stage of kernel development and ensiled for 200d. Treatments were fed to cows for 5wk, with the last week being used for statistical inferences. Week -1 was used as a covariate in the statistical analysis. Dry matter intake tended to be lower for cows fed corn silage treated with fungicide than CON (23.8, 23.0, 19.5, and 21.3kg for CON, 1X, 2X, and 3X, respectively). A linear treatment effect for DMI was observed, with DMI decreasing as foliar fungicide applications increased. Treatments CON, 1X, 2X, and 3X did not differ for milk yield (34.5, 34.5, 34.2, and 34.4kg/d, respectively); however, a trend for increased feed conversion represented by fat-corrected milk/DMI (1.65 vs. 1.47) and energy-corrected milk/DMI (1.60 vs. 1.43) was noted for cows fed corn silage with fungicide compared with CON. In conclusion, cows receiving corn silage treated with foliar fungicide had better conversion of feed dry matter to milk than those receiving CON silage. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Biotic and Abiotic Stimulation of Root Epidermal Cells Reveals Common and Specific Responses to Arbuscular Mycorrhizal Fungi1[W

PubMed Central

Genre, Andrea; Ortu, Giuseppe; Bertoldo, Chiara; Martino, Elena; Bonfante, Paola

2009-01-01

During arbuscular mycorrhizal (AM) colonization, a focal accumulation of organelles occurs in root epidermal cells, prior to fungal penetration, beneath adhering hyphopodia. This is followed by the appearance of the prepenetration apparatus (PPA), a transcellular column of cytoplasm connected to the nucleus and rich in cytoskeleton and secretory endomembranes. This apparatus appears to be responsible for the construction of an apoplastic compartment that confines the fungus within the cell lumen. To identify AM-specific elements within the PPA response, we challenged root cultures of Medicago truncatula, expressing a green fluorescent protein tag for the endoplasmic reticulum, with an AM symbiont, a necrotrophic pathogen, a hemibiotrophic pathogen, a noncompatible endomycorrhizal fungus, or abiotic physical stimuli. Parallel experiments were made on a M. truncatula nonsymbiotic mutant (doesn't make infections, dmi3-1). The results have highlighted a correlation between physical stimulation of the cell surface and nuclear repositioning. Cytoplasmic aggregation was only induced by contact with compatible fungi, whereas PPA appearance was specifically triggered by the AM fungus. The dmi3-1 mutant did not develop cytoplasmic aggregation or PPA and underwent cell death upon physical stimulation. The up-regulation of an expansin-like gene, already identified as an early marker of AM fungal contact, was triggered in wild-type roots by all the fungi tested. Such observations identify responses that are specific to mycorrhizal interactions and extend the role of the DMI3 protein, a calcium/calmodulin-dependent kinase, from symbiotic to pathogenic interactions. PMID:19151131

Decomposed direct matrix inversion for fast non-cartesian SENSE reconstructions.

PubMed

Qian, Yongxian; Zhang, Zhenghui; Wang, Yi; Boada, Fernando E

2006-08-01

A new k-space direct matrix inversion (DMI) method is proposed here to accelerate non-Cartesian SENSE reconstructions. In this method a global k-space matrix equation is established on basic MRI principles, and the inverse of the global encoding matrix is found from a set of local matrix equations by taking advantage of the small extension of k-space coil maps. The DMI algorithm's efficiency is achieved by reloading the precalculated global inverse when the coil maps and trajectories remain unchanged, such as in dynamic studies. Phantom and human subject experiments were performed on a 1.5T scanner with a standard four-channel phased-array cardiac coil. Interleaved spiral trajectories were used to collect fully sampled and undersampled 3D raw data. The equivalence of the global k-space matrix equation to its image-space version, was verified via conjugate gradient (CG) iterative algorithms on a 2x undersampled phantom and numerical-model data sets. When applied to the 2x undersampled phantom and human-subject raw data, the decomposed DMI method produced images with small errors (< or = 3.9%) relative to the reference images obtained from the fully-sampled data, at a rate of 2 s per slice (excluding 4 min for precalculating the global inverse at an image size of 256 x 256). The DMI method may be useful for noise evaluations in parallel coil designs, dynamic MRI, and 3D sodium MRI with fixed coils and trajectories. Copyright 2006 Wiley-Liss, Inc.

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Here the transparent furnace is extracted for servicing. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

A Water Model Study on Mixing Behavior of the Two-Layered Bath in Bottom Blown Copper Smelting Furnace

NASA Astrophysics Data System (ADS)

Shui, Lang; Cui, Zhixiang; Ma, Xiaodong; Jiang, Xu; Chen, Mao; Xiang, Yong; Zhao, Baojun

2018-05-01

The bottom-blown copper smelting furnace is a novel copper smelter developed in recent years. Many advantages of this furnace have been found, related to bath mixing behavior under its specific gas injection scheme. This study aims to use an oil-water double-phased laboratory-scale model to investigate the impact of industry-adjustable variables on bath mixing time, including lower layer thickness, gas flow rate, upper layer thickness and upper layer viscosity. Based on experimental results, an overall empirical relationship of mixing time in terms of these variables has been correlated, which provides the methodology for industry to optimize mass transfer in the furnace.

Cold blast furnace syndrome: a new source of toxic inhalation by nitrogen oxides

PubMed Central

Tague, I; Llewellin, P; Burton, K; Buchan, R; Yates, D

2004-01-01

Methods: Fourteen workers developed acute respiratory symptoms shortly after exposure to "air blast" from blast furnace tuyeres. These included chest tightness, dyspnoea, rigors, and diaphoresis. Chest radiographs showed pulmonary infiltrates, and lung function a restrictive abnormality. This report includes a description of clinical features of the affected workers and elucidation of the probable cause of the outbreak. Results: Clinical features and occupational hygiene measurements suggested the most likely cause was inhalation of nitrogen oxides at high pressure and temperature. While the task could not be eliminated, engineering controls were implemented to control the hazard. No further cases have occurred. Conclusions: "Cold blast furnace syndrome" represents a previously undescribed hazard of blast furnace work, probably due to inhalation of nitrogen oxides. It should be considered in the differential diagnosis of acute toxic inhalational injuries in blast furnace workers. PMID:15090669

Study on Dezincification and De-Lead of Blast Furnace Dust by Fluidized Reduction Experiment

NASA Astrophysics Data System (ADS)

Yang, Shufeng; Liu, Chengsong; Gao, Xiaojie; Li, Jingshe

In the blast furnace process, the dust entrained in the blast furnace gas enters into the down-comer, flows through the gravity dust separator (to eliminate coarse particles) and then is collected in a bag-house. The powder collected by the baghouse is called bag dust, while both fractions are called blast furnace dust whose main components are C and Fe. The dust also contains small amounts of nonferrous metals such as Zn and Pb, which have some value. Also, due to the small particle size and low density the dust is easily suspended in air and so can endanger human health. Therefore it is necessary to develop a process to both treat the dust to recover the metal values and to dispose of the residue — preferably by recycling to the blast furnace itself via the sinter strand. These objectives will result in good economic, environmental and social benefits [1].

Detailed model for practical pulverized coal furnaces and gasifiers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, P.J.; Smoot, L.D.

1989-08-01

This study has been supported by a consortium of nine industrial and governmental sponsors. Work was initiated on May 1, 1985 and completed August 31, 1989. The central objective of this work was to develop, evaluate and apply a practical combustion model for utility boilers, industrial furnaces and gasifiers. Key accomplishments have included: Development of an advanced first-generation, computer model for combustion in three dimensional furnaces; development of a new first generation fouling and slagging submodel; detailed evaluation of an existing NO{sub x} submodel; development and evaluation of an improved radiation submodel; preparation and distribution of a three-volume final report:more » (a) Volume 1: General Technical Report; (b) Volume 2: PCGC-3 User's Manual; (c) Volume 3: Data Book for Evaluation of Three-Dimensional Combustion Models; and organization of a user's workshop on the three-dimensional code. The furnace computer model developed under this study requires further development before it can be applied generally to all applications; however, it can be used now by specialists for many specific applications, including non-combusting systems and combusting geseous systems. A new combustion center was organized and work was initiated to continue the important research effort initiated by this study. 212 refs., 72 figs., 38 tabs.« less

Theoretical studies of charge transfer and proton transfer complex formation between 3,5-dinitrobenzic acid and 1,2-dimethylimidazole

NASA Astrophysics Data System (ADS)

Afroz, Ziya; Faizan, Mohd.; Alam, Mohammad Jane; Ahmad, Shabbir; Ahmad, Afaq

2018-05-01

Natural atomic charge analysis and molecular electrostatic potential (MEP) surface analysis of hydrogen bonded charge transfer (HBCT) and proton transfer (PT) complex of 3,5-dinitrobenzoic acid (DNBA) and 1,2-dimethylimidazole (DMI) have been investigated by theoretical modelling using widely employed DFT/B3LYP/6-311G(d,p) level of theory. Along with this analysis, Hirshfeld surface study of the intermolecular interactions and associated 2D finger plot for reported PT complex between DNBA and DMI have been explored.

Experiment/facility requirements document for the Space Station Furnace Facility. Section 1: Integrated configuration

NASA Astrophysics Data System (ADS)

1992-05-01

The function of the Space Station Furnace Facility (SSFF) is to support materials research into the crystal growth and solidification processes of electronic and photonic materials, metals and alloys, and glasses and ceramics. To support this broad base of research requirements, the SSFF will employ a variety of furnace modules which will be operated, regulated, and supported by a core of common subsystems. Furnace modules may be reconfigured or specifically developed to provide unique solidification conditions for each set of experiments. The SSFF modular approach permits the addition of new or scaled-up furnace modules to support the evolution of the facility as new science requirements are identified. The SSFF Core is of modular design to permit augmentation for enhanced capabilities. The fully integrated configuration of the SSFF will consist of three racks with the capability of supporting up to two furnace modules per rack. The initial configuration of the SSFF will consist of two of the three racks and one furnace module. This Experiment/Facility Requirements Document (E/FRD) describes the integrated facility requirements for the Space Station Freedom (SSF) Integrated Configuration-1 (IC1) mission. The IC1 SSFF will consist of two racks: the Core Rack, with the centralized subsystem equipment; and the Experiment Rack-1, with Furnace Module-1 and the distributed subsystem equipment to support the furnace. The SSFF support functions are provided by the following Core subsystems: power conditioning and distribution subsystem (SSFF PCDS); data management subsystem (SSFF DMS); thermal control Subsystem (SSFF TCS); gas distribution subsystem (SSFF GDS); and mechanical structures subsystem (SSFF MSS).

Experiment/facility requirements document for the Space Station Furnace Facility. Section 1: Integrated configuration

NASA Technical Reports Server (NTRS)

1992-01-01

The function of the Space Station Furnace Facility (SSFF) is to support materials research into the crystal growth and solidification processes of electronic and photonic materials, metals and alloys, and glasses and ceramics. To support this broad base of research requirements, the SSFF will employ a variety of furnace modules which will be operated, regulated, and supported by a core of common subsystems. Furnace modules may be reconfigured or specifically developed to provide unique solidification conditions for each set of experiments. The SSFF modular approach permits the addition of new or scaled-up furnace modules to support the evolution of the facility as new science requirements are identified. The SSFF Core is of modular design to permit augmentation for enhanced capabilities. The fully integrated configuration of the SSFF will consist of three racks with the capability of supporting up to two furnace modules per rack. The initial configuration of the SSFF will consist of two of the three racks and one furnace module. This Experiment/Facility Requirements Document (E/FRD) describes the integrated facility requirements for the Space Station Freedom (SSF) Integrated Configuration-1 (IC1) mission. The IC1 SSFF will consist of two racks: the Core Rack, with the centralized subsystem equipment; and the Experiment Rack-1, with Furnace Module-1 and the distributed subsystem equipment to support the furnace. The SSFF support functions are provided by the following Core subsystems: power conditioning and distribution subsystem (SSFF PCDS); data management subsystem (SSFF DMS); thermal control Subsystem (SSFF TCS); gas distribution subsystem (SSFF GDS); and mechanical structures subsystem (SSFF MSS).

A Heat and Mass Transfer Model of a Silicon Pilot Furnace

NASA Astrophysics Data System (ADS)

Sloman, Benjamin M.; Please, Colin P.; Van Gorder, Robert A.; Valderhaug, Aasgeir M.; Birkeland, Rolf G.; Wegge, Harald

2017-10-01

The most common technological route for metallurgical silicon production is to feed quartz and a carbon source ( e.g., coal, coke, or charcoal) into submerged-arc furnaces, which use electrodes as electrical conductors. We develop a mathematical model of a silicon furnace. A continuum approach is taken, and we derive from first principles the equations governing the time evolution of chemical concentrations, gas partial pressures, velocity, and temperature within a one-dimensional vertical section of a furnace. Numerical simulations are obtained for this model and are shown to compare favorably with experimental results obtained using silicon pilot furnaces. A rising interface is shown to exist at the base of the charge, with motion caused by the heating of the pilot furnace. We find that more reactive carbon reduces the silicon monoxide losses, while reducing the carbon content in the raw material mixture causes greater solid and liquid material to build-up in the charge region, indicative of crust formation (which can be detrimental to the silicon production process). We also comment on how the various findings could be relevant for industrial operations.

Rapidly solidified titanium alloys by melt overflow

NASA Technical Reports Server (NTRS)

Gaspar, Thomas A.; Bruce, Thomas J., Jr.; Hackman, Lloyd E.; Brasmer, Susan E.; Dantzig, Jonathan A.; Baeslack, William A., III

1989-01-01

A pilot plant scale furnace was designed and constructed for casting titanium alloy strips. The furnace combines plasma arc skull melting techniques with melt overflow rapid solidification technology. A mathematical model of the melting and casting process was developed. The furnace cast strip of a suitable length and width for use with honeycomb structures. Titanium alloys Ti-6Al-4V and Ti-14Al-21 Nb were successfully cast into strips. The strips were evaluated by optical metallography, microhardness measurements, chemical analysis, and cold rolling.

Improvement of calculation method for electrical parameters of short network of ore-thermal furnaces

NASA Astrophysics Data System (ADS)

Aliferov, A. I.; Bikeev, R. A.; Goreva, L. P.

2017-10-01

The paper describes a new calculation method for active and inductive resistance of split interleaved current leads packages in ore-thermal electric furnaces. The method is developed on basis of regression analysis of dependencies of active and inductive resistances of the packages on their geometrical parameters, mutual disposition and interleaving pattern. These multi-parametric calculations have been performed with ANSYS software. The proposed method allows solving split current lead electrical parameters minimization and balancing problems for ore-thermal furnaces.

NOx Emission Reduction by Oscillating combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Institute of Gas Technology

2004-01-30

High-temperature, natural gas-fired furnaces, especially those fired with preheated air, produce large quantities of NO{sub x} per ton of material processed. Regulations on emissions from industrial furnaces are becoming increasingly more stringent. In addition, competition is forcing operators to make their furnaces more productive and/or efficient. Switching from preheated air to industrial oxygen can increase efficiency and reduce NO{sub x}, but oxygen is significantly more costly than air and may not be compatible with the material being heated. What was needed, and what was developed during this project, is a technology that reduces NO{sub x} emissions while increasing furnace efficiencymore » for both air- and oxy-fired furnaces. Oscillating combustion is a retrofit technology that involves the forced oscillation of the fuel flow rate to a furnace. These oscillations create successive, fuel-rich and fuel-lean zones within the furnace. Heat transfer from the flame to the load increases due to the more luminous fuel-rich zones, a longer overall flame length, and the breakup of the thermal boundary layer. The increased heat transfer shortens heat up times, thereby increasing furnace productivity, and reduces the heat going up the stack, thereby increasing efficiency. The fuel-rich and fuel-lean zones also produce substantially less NO{sub x} than firing at a constant excess air level. The longer flames and higher heat transfer rate reduces overall peak flame temperature and thus reduces additional NO{sub x} formation from the eventual mixing of the zones and burnout of combustibles from the rich zones. This project involved the development of hardware to implement oscillating combustion on an industrial scale, the laboratory testing of oscillating combustion on various types of industrial burners, and the field testing of oscillating combustion on several types of industrial furnace. Before laboratory testing began, a market study was conducted, based on the attributes of oscillating combustion and on the results of an earlier project at GTI and Air Liquide, to determine which applications for oscillating combustion would show the greatest probability for technical success and greatest probability for market acceptability. The market study indicated that furnaces in the steel, glass, and metal melting industries would perform well in both categories. These findings guided the selection of burners for laboratory testing and, with the results of the laboratory testing, guided the selection of field test sites.« less

NOx Emission Reduction by Oscillating Combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

John C. Wagner

2004-03-31

High-temperature, natural gas-fired furnaces, especially those fired with preheated air, produce large quantities of NO{sub x} per ton of material processed. Regulations on emissions from industrial furnaces are becoming increasingly more stringent. In addition, competition is forcing operators to make their furnaces more productive and/or efficient. Switching from preheated air to industrial oxygen can increase efficiency and reduce NO{sub x}, but oxygen is significantly more costly than air and may not be compatible with the material being heated. What was needed, and what was developed during this project, is a technology that reduces NO{sub x} emissions while increasing furnace efficiencymore » for both air- and oxy-fired furnaces. Oscillating combustion is a retrofit technology that involves the forced oscillation of the fuel flow rate to a furnace. These oscillations create successive, fuel-rich and fuel-lean zones within the furnace. Heat transfer from the flame to the load increases due to the more luminous fuel-rich zones, a longer overall flame length, and the breakup of the thermal boundary layer. The increased heat transfer shortens heat up times, thereby increasing furnace productivity, and reduces the heat going up the stack, thereby increasing efficiency. The fuel-rich and fuel-lean zones also produce substantially less NO{sub x} than firing at a constant excess air level. The longer flames and higher heat transfer rate reduces overall peak flame temperature and thus reduces additional NO{sub x} formation from the eventual mixing of the zones and burnout of combustibles from the rich zones. This project involved the development of hardware to implement oscillating combustion on an industrial scale, the laboratory testing of oscillating combustion on various types of industrial burners, and the field testing of oscillating combustion on several types of industrial furnace. Before laboratory testing began, a market study was conducted, based on the attributes of oscillating combustion and on the results of an earlier project at GTI and Air Liquide, to determine which applications for oscillating combustion would show the greatest probability for technical success and greatest probability for market acceptability. The market study indicated that furnaces in the steel, glass, and metal melting industries would perform well in both categories. These findings guided the selection of burners for laboratory testing and, with the results of the laboratory testing, guided the selection of field test sites.« less

Dilute Oxygen Combustion Phase IV Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riley, M.F.

2003-04-30

Novel furnace designs based on Dilute Oxygen Combustion (DOC) technology were developed under subcontract by Techint Technologies, Coraopolis, PA, to fully exploit the energy and environmental capabilities of DOC technology and to provide a competitive offering for new furnace construction opportunities. Capital cost, fuel, oxygen and utility costs, NOx emissions, oxide scaling performance, and maintenance requirements were compared for five DOC-based designs and three conventional air5-fired designs using a 10-year net present value calculation. A furnace direct completely with DOC burners offers low capital cost, low fuel rate, and minimal NOx emissions. However, these benefits do not offset the costmore » of oxygen and a full DOC-fired furnace is projected to cost $1.30 per ton more to operate than a conventional air-fired furnace. The incremental cost of the improved NOx performance is roughly $6/lb NOx, compared with an estimated $3/lb. NOx for equ8pping a conventional furnace with selective catalytic reduction (SCCR) technology. A furnace fired with DOC burners in the heating zone and ambient temperature (cold) air-fired burners in the soak zone offers low capital cost with less oxygen consumption. However, the improvement in fuel rate is not as great as the full DOC-fired design, and the DOC-cold soak design is also projected to cost $1.30 per ton more to operate than a conventional air-fired furnace. The NOx improvement with the DOC-cold soak design is also not as great as the full DOC fired design, and the incremental cost of the improved NOx performance is nearly $9/lb NOx. These results indicate that a DOC-based furnace design will not be generally competitive with conventional technology for new furnace construction under current market conditions. Fuel prices of $7/MMBtu or oxygen prices of $23/ton are needed to make the DOC furnace economics favorable. Niche applications may exist, particularly where access to capital is limited or floor space limitations are critical. DOC technology will continue to have a highly competitive role in retrofit applications requiring increases in furnace productivity.« less

The effects of forage proportion and rapidly degradable dry matter from concentrate on ruminal digestion in dairy cows fed corn silage-based diets with fixed neutral detergent fiber and starch contents.

PubMed

Lechartier, C; Peyraud, J-L

2010-02-01

This study investigated the effects of the forage-to-concentrate (F:C) ratio and the rate of ruminal degradation of carbohydrates from the concentrate on digestion in dairy cows fed corn silage-based diets. Six cows with ruminal cannulas were assigned to 6 treatments in a 6x6 Latin square. Treatments were arranged in a 3x2 factorial design. Three proportions of neutral detergent fiber from forage [FNDF; 7.6, 13.2, and 18.9% of dry matter (DM)] were obtained by modifying F:C (20:80, 35:65, and 50:50). These F:C were combined with concentrates with either high or low content of rapidly degradable carbohydrates. The dietary content of rapidly degradable carbohydrates from the concentrate was estimated from the DM disappearance of concentrate after 4h of in sacco incubation (CRDM). Thus, 2 proportions of CRDM were tested (20 and 30% of DM). Wheat and corn grain were used as rapidly and slowly degradable starch sources, respectively. Soybean hulls and citrus pulp were used as slowly and rapidly degradable fiber sources, respectively. Concentrate composition was adjusted to maintain dietary starch and neutral detergent fiber contents at 35.9 and 28.9% of DM, respectively. There was no effect of the interaction between F:C and CRDM on DM intake (DMI), ruminal fermentation, chewing activity, and fibrolytic activity. When F:C decreased, DMI increased, the mean ruminal pH linearly decreased, and the pH range linearly increased from 0.95 to 1.27 pH unit. At the same time, the acetate-to-propionate ratio decreased linearly. Decreasing F:C linearly decreased the average time spent chewing per kilogram of DMI from 35.2 to 19.5min/kg of DMI and decreased ruminal liquid outflow from 11.6 to 9.2L/kg of DMI, suggesting a decrease in the salivary flow. Increasing CRDM decreased DMI and increased the time during which pH was below 6.0 (3.1 vs. 4.8h), the pH range (0.90 vs. 1.33), and the initial rate of pH drop. It also increased the volatile fatty acid range (35 vs. 59mM), thus suggesting an increased rate of fermentation. It also decreased the acetate-to-propionate ratio (2.9 vs. 1.8). Increasing CRDM barely affected the average time spent chewing per kilogram of DMI and the ruminal liquid outflow. These results suggest that rumen pH is controlled by different mechanisms when F:C is decreased or when CRDM is increased. Consequently, FNDF is a good predictor of the chewing time, whereas CRDM is a good predictor of the pH range and volatile fatty acid profiles. Finally, considering both FNDF and CRDM improves the prediction of mean pH. Copyright 2010 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of prepartum diets supplemented with rolled oilseeds on calf birth weight, postpartum health, feed intake, milk yield, and reproductive performance of dairy cows.

PubMed

Salehi, R; Colazo, M G; Oba, M; Ambrose, D J

2016-05-01

The objectives were to determine the effects of supplemental fat (no oilseed vs. oilseed) during late gestation and the source of fat (canola vs. sunflower seed), on dry matter intake (DMI), plasma metabolite concentrations, milk production and composition, calf birth weight, postpartum health disorders, ovarian function and reproductive performance in dairy cows. Pregnant Holstein cows, blocked by body condition and parity, were assigned to 1 of 3 diets containing rolled canola seed (high in oleic acid; n=43) or sunflower (high in linoleic acid; n=45) at 8% of dry matter, or no oilseed (control; n=43), for the last 35±2 d of pregnancy. After calving, all cows received a common lactation diet. Blood samples were collected at wk -3 (i.e., 2 wk after initiation of prepartum diets) and at wk +1, +2, +3, +4 and +5 postpartum to determine the concentration of fatty acids (mEq/dL), β-hydroxybutyrate (mg/dL), and glucose (mg/dL). Ovarian ultrasonography was performed twice weekly to determine the first appearance of dominant (10mm) and preovulatory-size (≥16mm) follicles, and ovulation. Uterine inflammatory status based on the proportion of polymorphonuclear leukocytes (PMN; subclinical endometritis: >8% PMN) was assessed at d 25±1 postpartum. Significant parity by treatment interactions were observed for DMI and milk yield. Prepartum oilseed supplementation, more specifically sunflower seed supplementation, increased postpartum DMI in primiparous cows without affecting prepartum DMI or milk yield. Contrarily, in multiparous cows, prepartum oilseed supplementation decreased both prepartum and postpartum DMI and milk yield during the first 2 wk. Regardless of parity, prepartum feeding of canola reduced postpartum DMI compared with those fed sunflower. Mean fatty acids concentrations at wk -3 were greater in cows given supplemental oilseed than those fed no oilseeds. Gestation length and calf birth weight were increased in cows given supplemental oilseed prepartum compared with cows fed no oilseeds, and a disproportionate increase in the birth weight of female calves was evident in cows fed oilseed. Total reproductive disorders tended to be greater in cows fed supplemental oilseed than those fed no oilseed (42 vs. 23%). Furthermore, cows fed sunflower seed had greater incidences of dystocia (35 vs. 18%) and total health disorders (52 vs. 32%) than those fed canola seed. Added oilseed and type of oilseed did not affect uterine inflammation at 25±1 d postpartum. Oilseed supplementation did not alter the intervals from calving to establishment of the first dominant follicle, preovulatory-size follicle, and ovulation, nor did it affect fertility (conception rate to first artificial insemination and proportion of pregnant cows by 150 d after calving). In summary, prepartum oilseed supplementation (6.2 to 7.4% ether extract, % of dietary dry matter) decreased DMI during the entire experimental period (pre- and postpartum), decreased milk yield during early lactation in multiparous cows, and increased calf birth weight with no significant improvement in ovarian function and reproductive performance. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Development and Implementation of the Casting of Rods Made of Refractory Cast Alloys

NASA Astrophysics Data System (ADS)

Kabanov, I. V.; Urin, S. L.; Ivanyuk, A. S.; Nesterov, A. N.; Bogdanov, S. V.

2017-12-01

The problems of the production of a so-called casting rod blank made of a refractory casting alloy in the vacuum induction furnaces of AO Metallurgical Plant Electrostal are considered. A unique technology of casting and subsequent treatment of as-cast rod blanks made of refractory alloys is developed, tested, and optimized. As a result of the developed and performed measures for the production of metal products in the Consarc furnace, the ingot-to-product yield increases by 15% as compared to metal casting in an ISV-1.0 furnace. As a result, we have widened the range of cast alloy grades and are going to cast metals for the manufacture of blanks of other sizes and ranges of alloy an steel grades.

Short communication: Feed utilization and its associations with fertility and productive life in 11 commercial Pennsylvania tie-stall herds.

PubMed

Vallimont, J E; Dechow, C D; Daubert, J M; Dekleva, M W; Blum, J W; Liu, W; Varga, G A; Heinrichs, A J; Baumrucker, C R

2013-02-01

The objectives of this study were to quantify the relationships of various definitions of feed utilization with both fertility and productive life. Intake and body measurement data were collected monthly on 970 cows in 11 tie-stall herds for 6 consecutive months. Measures of feed utilization for this study were dry matter intake (DMI), dry matter intake efficiency (DME, defined as 305-d fat-corrected milk/305-d DMI), DME with intake adjusted for maintenance requirements (DMEM), crude protein efficiency (defined as 305-d protein yield/305-d crude protein intake), and 2 definitions of residual feed intake (RFI). The first, RFI(reg), was calculated by regressing daily DMI on daily milk, fat, and protein yields, body weight (BW), daily body condition score (BCS) gain or loss, the interaction between BW and BCS gain or loss, and days in milk. The second, RFI(NRC), was estimated by subtracting 305-d DMI predicted according to their fat-corrected milk and BW from actual 305-d DMI. Data were analyzed with 8-trait animal models and included one measure of feed utilization and milk, fat, and protein yields, BW, BCS, days open (DO), and productive life (PL). The genetic correlation between DME and DO was 0.53 (± 0.19) and that between DME and PL was 0.66 (± 0.10). These results show that cows who had higher feed efficiency had greater DO (undesirable) and greater PL (desirable). Results were similar for the genetic correlation between DO and crude protein efficiency (0.42). Productive life had genetic correlations of -0.22 with BW and -0.48 with BCS, suggesting that larger, fatter cows in this study had shorter PL. Correlations between estimated breeding values for feed utilization and official sire genetic evaluations for fertility were in agreement with the results from the multiple-trait models. Selection programs intended to enhance feed efficiency should factor relationships with functional traits to avoid unfavorable effects on cow fertility. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Inherent Resistance to 14α-demethylation Inhibitor Fungicides in Colletotrichum truncatum is likely linked to CYP51A and/or CYP51B Gene Variants.

PubMed

Chen, Shuning; Wang, Yunyun; Schnabel, Guido; Peng, Congyue Annie; Lagishetty, Satyanarayana; Smith, Kerry; Luo, Chao-Xi; Yuan, Huizhu

2018-05-24

Anthracnose disease, caused by Colletotrichum truncatum, affects marketable yield during preharvest production and postharvest storage of fruits and vegetables worldwide. Demethylation inhibitor fungicides (DMIs) are among the very few chemical classes of single-site mode of action fungicides that are effective in controlling anthracnose disease. However, some species are inherently resistant to DMIs and more information is needed to understand this phenomenon. Isolates of C. truncatum were collected from the USA and China from peach, soybean, citrus, and begonia and sensitivity to six DMIs (difenoconazole, propiconazole, metconazole, tebuconazole, flutriafol and fenbuconazole) was determined. Compared with DMI sensitive isolates of C. fructicola, C. siamense, and C. fioriniae (EC50 value ranging from 0.03 µg/ml to 16.2 µg/ml to six DMIs), C. truncatum and C. nymphaeae were resistant to flutriafol and fenbuconazole (with EC50 value of more 50 µg/ml). Moreover, C. truncatum was resistant to tebuconazole and metconazole (with resistance factor of 27.4 and 96.0), and displayed reduced sensitivity to difenoconazole and propiconazole (with resistance factor of 5.1 and 5.2). Analysis of the Colletotrichum spp. genome revealed two potential DMI targets, CYP51A and CYP51B, that putatively encode P450 sterol 14α-demethylases. Both genes were identified and sequenced from C. truncatum and other species and no correlation between CYP51 gene expression levels and fungicide sensitivity was found. Four amino acid variations L208Y, H238R, S302A, and I366L in CYP51A, and three variations H373N, M376L, and S511T in CYP51B correlated with the DMI resistance phenotype. CYP51A structure model analysis suggested the four alteration may reduce azole affinity. Likewise, CYP51B structure analysis suggested the H373N and M376L variants may change the conformation of the DMI binding pocket, thereby causing differential sensitivity to DMI fungicides in C. truncatum.

Performance of dairy cows fed high levels of acetic acid or ethanol.

PubMed

Daniel, J L P; Amaral, R C; Sá Neto, A; Cabezas-Garcia, E H; Bispo, A W; Zopollatto, M; Cardoso, T L; Spoto, M H F; Santos, F A P; Nussio, L G

2013-01-01

Ethanol and acetic acid are common end products from silages. The main objective of this study was to determine whether high concentrations of ethanol or acetic acid in total mixed ration would affect performance in dairy cows. Thirty mid-lactation Holstein cows were grouped in 10 blocks and fed one of the following diets for 7 wk: (1) control (33% Bermuda hay + 67% concentrates), (2) ethanol [control diet + 5% ethanol, dry matter (DM) basis], or (3) acetic acid (control diet + 5% acetic acid, DM basis). Ethanol and acetic acid were diluted in water (1:2) and sprayed onto total mixed rations twice daily before feeding. An equal amount of water was mixed with the control ration. To adapt animals to these treatments, cows were fed only half of the treatment dose during the first week of study. Cows fed ethanol yielded more milk (37.9 kg/d) than those fed the control (35.8 kg/d) or acetic acid (35.3 kg/d) diets, mainly due to the higher DM intake (DMI; 23.7, 22.2, and 21.6 kg/d, respectively). The significant diet × week interaction for DMI, mainly during wk 2 and 3 (when acetic acid reached the full dose), was related to the decrease in DMI observed for the acetic acid treatment. There was a diet × week interaction in excretion of milk energy per DMI during wk 2 and 3, due to cows fed acetic acid sustained milk yield despite lower DMI. Energy efficiency was similar across diets. Blood metabolites (glucose, insulin, nonesterified fatty acids, ethanol, and γ-glutamyl transferase activity) and sensory characteristics of milk were not affected by these treatments. Animal performance suggested similar energy value for the diet containing ethanol compared with other diets. Rumen conversion of ethanol to acetate and a concomitant increase in methane production might be a plausible explanation for the deviation of the predicted energy value based on the heat of combustion. Therefore, the loss of volatile compounds during the drying process in the laboratory should be considered when calculating energy content of fermented feedstuffs. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Nutrient intake, digestibility and performance of Gaddi kids supplemented with tea seed or tea seed saponin extract.

PubMed

Kumar, M; Kannan, A; Bhar, R; Gulati, A; Gaurav, A; Sharma, V K

2017-04-01

An experiment was conducted to determine the nutrient intake, digestibility, microbial protein synthesis, haemato-biochemical attributes, immune response and growth performance of Gaddi kids fed with oat fodder based basal diet supplemented with either tea seed or tea seed saponin (TSS) extract. Eighteen male kids, 7.03±0.16 months of age and 19.72±0.64 kg body weight, were distributed into three groups, T 0 (control), T 1 , and T 2 , consisting of 6 animals each in a completely randomized design. The kids were fed a basal diet consisting of concentrate mixture and oat fodder (50:50). Animals in group III (T 2 ) were supplemented with TSS at 0.4% of dry matter intake (DMI), and group II (T 1 ) were supplemented with tea seed at 2.6% of DMI to provide equivalent dose of TSS as in T 2 . Two metabolism trials were conducted, 1st after 21 days and 2nd after 90 days of feeding to evaluate the short term and long term effects of supplementation. The tea seed (T 1 ) or TSS (T 2 ) supplementation did not affect DMI as well as the digestibility of dry matter, organic matter, crude protein, neutral detergent fibre, and acid detergent fibre. Nutritive value of diet and plane of nutrition were also comparable for both the periods. However, the average daily gain and feed conversion ratio (FCR) were improved (p<0.05) for T 1 and T 2 as compared to T 0 . The microbial protein supply was also higher (p<0.05) for T 1 and T 2 for both the periods. There was no effect of supplementation on most blood parameters. However, the triglyceride and low density lipoprotein cholesterol levels decreased (p<0.05) and high density lipoprotein-cholesterol level increased (p<0.05) in T 2 as compared with T 0 and T 1 . Supplementation also did not affect the cell mediated and humoral immune response in goats. Tea seed at 2.6% of DMI and TSS at 0.4% DMI can be fed to Gaddi goats to improve growth rate, FCR and microbial protein synthesis.

Genetic analysis of efficiency traits in Austrian dairy cattle and their relationships with body condition score and lameness.

PubMed

Köck, A; Ledinek, M; Gruber, L; Steininger, F; Fuerst-Waltl, B; Egger-Danner, C

2018-01-01

This study is part of a larger project whose overall objective was to evaluate the possibilities for genetic improvement of efficiency in Austrian dairy cattle. In 2014, a 1-yr data collection was carried out. Data from 6,519 cows kept on 161 farms were recorded. In addition to routinely recorded data (e.g., milk yield, fertility, disease data), data of novel traits [e.g., body weight (BW), body condition score (BCS), lameness score, body measurements] and individual feeding information and feed quality were recorded on each test-day. The specific objective of this study was to estimate genetic parameters for efficiency (related) traits and to investigate their relationships with BCS and lameness in Austrian Fleckvieh, Brown Swiss, and Holstein cows. The following efficiency (related) traits were considered: energy-corrected milk (ECM), BW, dry matter intake (DMI), energy intake (INEL), ratio of milk output to metabolic BW (ECM/BW 0.75 ), ratio of milk output to DMI (ECM/DMI), and ratio of milk energy output to total energy intake (LE/INEL, LE = energy in milk). For Fleckvieh, the heritability estimates of the efficiency (related) traits ranged from 0.11 for LE/INEL to 0.44 for BW. Heritabilities for BCS and lameness were 0.19 and 0.07, respectively. Repeatabilities were high and ranged from 0.30 for LE/INEL to 0.83 for BW. Heritability estimates were generally lower for Brown Swiss and Holstein, but repeatabilities were in the same range as for Fleckvieh. In all 3 breeds, more-efficient cows were found to have a higher milk yield, lower BW, slightly higher DMI, and lower BCS. Higher efficiency was associated with slightly fewer lameness problems, most likely due to the lower BW (especially in Fleckvieh) and higher DMI of the more-efficient cows. Body weight and BCS were positively correlated. Therefore, when selecting for a lower BW, BCS is required as additional information because, otherwise, no distinction between large animals with low BCS and smaller animals with normal BCS would be possible. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The 14alpha-Demethylasse(CYP51A1) Gene is Overexpressed in Venturia inaequalis Strains Resistant to Myclobutanil.

PubMed

Schnabel, G; Jones, A L

2001-01-01

ABSTRACT We identified the cytochrome P450 sterol 14alpha-demethylase (CYP51A1) gene from Venturia inaequalis and optional insertions located upstream from CYP51A1 and evaluated their potential role in conferring resistance to the sterol demethylation-inhibitor (DMI) fungicide my-clobutanil. The CYP51A1 gene was completely sequenced from one my-clobutanil sensitive (S) and two myclobutanil-resistant (R) strains. No nucleotide variation was found when the three sequences were aligned. Allele-specific polymerase chain reaction (PCR) analysis indicated that a previously described single base pair mutation that correlated with resistance to DMI fungicides in strains of other filamentous fungi was absent in 19 S and 32 R strains of V. inaequalis from Michigan and elsewhere. The sequencing results and PCR analyses suggest that resistance in these strains was not due to a mutation in the sterol demethylase target site for DMI fungicides. Expression of CYP51A1 was determined for strains from an orchard that had never been sprayed with DMI fungicides (baseline orchard), and the data provided a reference for evaluating the expression of strains collected from a research orchard and from three commercial Michigan apple orchards with a long history of DMI use and a high frequency of R strains. Overexpression of CYP51A1 was significantly higher in 9 of 11 R strains from the research orchard than in S strains from the baseline orchard. The high expression was correlated with the presence of a 553-bp insertion located upstream of CYP51A1. Overexpression of the CYP51A1 gene was also detected in eight of eight, five of nine, and nine of nine R strains from three commercial orchards, but the insertion was not detected in the majority of these strains. The results suggest that overexpression of the target-site CYP51A1 gene is an important mechanism of resistance in some field resistant strains of V. inaequalis, but other mechanisms of resistance also appear to exist.

Who's distressed? A comparison of diabetes-related distress by type of diabetes and medication.

PubMed

Wardian, Jana L; Tate, Joshua; Folaron, Irene; Graybill, Sky; True, Mark; Sauerwein, Tom

2018-03-07

We hypothesized that diabetes-related distress would vary by type of diabetes and medication regimen [Type 1 diabetes (T1DM), Type 2 diabetes with insulin use (T2DM-i), Type 2 diabetes without insulin use (T2DM)]. Thus, the aim of this study was to identify groups with elevated diabetes-related distress. We administered the 17-item Diabetes-related Distress Scale (DDS-17) to 585 patients. We collected demographics, medications, and lab results from patient records. Patients were categorized by type of diabetes and medication: T1DM (n = 149); T2DM-i (n = 333); and T2DM (n = 103). ANOVA revealed significant differences in sample characteristics. ANCOVA were conducted on all four DDS-17 domains [Emotional Burden (EB); Physician-related Distress (PD); Regimen-related Distress (RD); and Interpersonal Distress (ID)]; covariates included in the models were sex, age, duration of diabetes, BMI, and HbA1c. EB was significantly lower in T1DM than T2DM-i, p < 0.05. In addition, RD was significantly lower in T1DM than either T2DM-i, p < 0.05 and T2DM, p < 0.05. EB and RD are higher for those with type 2 diabetes. Thus, interventions to reduce EB and RD need to be considered for patients with type 2 diabetes. DDS-17 is useful in identifying diabetes-related distress in patients with diabetes. Efforts need to be made to reduce EB and RD. Published by Elsevier B.V.

Terahertz-Frequency Spin Hall Auto-oscillator Based on a Canted Antiferromagnet

NASA Astrophysics Data System (ADS)

Sulymenko, O. R.; Prokopenko, O. V.; Tiberkevich, V. S.; Slavin, A. N.; Ivanov, B. A.; Khymyn, R. S.

2017-12-01

We propose a design of a terahertz-frequency signal generator based on a layered structure consisting of a current-driven platinum (Pt) layer and a layer of an antiferromagnet (AFM) with easy-plane anisotropy, where the magnetization vectors of the AFM sublattices are canted inside the easy plane by the Dzyaloshinskii-Moriya interaction (DMI). The dc electric current flowing in the Pt layer creates due to the spin Hall effect, a perpendicular spin current that, being injected in the AFM layer, tilts the DMI-canted AFM sublattices out of the easy plane, thus exposing them to the action of a strong internal exchange magnetic field of the AFM. The sublattice magnetizations, along with the small net magnetization vector mDMI of the canted AFM, start to rotate about the hard anisotropy axis of the AFM with the terahertz frequency proportional to the injected spin current and the AFM exchange field. The rotation of the small net magnetization mDMI results in the terahertz-frequency dipolar radiation that can be directly received by an adjacent (e.g., dielectric) resonator. We demonstrate theoretically that the radiation frequencies in the range f =0.05 - 2 THz are possible at the experimentally reachable magnitudes of the driving current density, and we evaluate the power of the signal radiated into different types of resonators. This power increases with the increase of frequency f , and it can exceed 1 μ W at f ˜0.5 THz for a typical dielectric resonator of the electric permittivity ɛ ˜10 and a quality factor Q ˜750 .

The expression of plasticity-related genes in an acute model of stress is modulated by chronic desipramine in a time-dependent manner within medial prefrontal cortex.

PubMed

Nava, Nicoletta; Treccani, Giulia; Müller, Heidi Kaastrup; Popoli, Maurizio; Wegener, Gregers; Elfving, Betina

2017-01-01

It is well established that stress plays a major role in the pathogenesis of neuropsychiatric diseases. Stress-induced alteration of synaptic plasticity has been hypothesized to underlie the morphological changes observed by neuroimaging in psychiatric patients in key regions such as hippocampus and prefrontal cortex (PFC). We have recently shown that a single acute stress exposure produces significant short-term alterations of structural plasticity within medial PFC. These alterations were partially prevented by previous treatment with chronic desipramine (DMI). In the present study we evaluated the effects of acute Foot-shock (FS)-stress and pre-treatment with the traditional antidepressant DMI on the gene expression of key regulators of synaptic plasticity and structure. Expression of Homer, Shank, Spinophilin, Densin-180, and the small RhoGTPase related gene Rac1 and downstream target genes, Limk1, Cofilin1 and Rock1 were investigated 1 day (1d), 7 d and 14d after FS-stress exposure. We found that DMI specifically increases the short-term expression of Spinophilin, as well as Homer and Shank family genes, and that both acute stress and DMI exert significant long-term effects on mRNA levels of genes involved in spine plasticity. These findings support the knowledge that acute FS stress and antidepressant treatment induce both rapid and sustained time-dependent alterations in structural components of synaptic plasticity in rodent medial PFC. Copyright © 2016 Elsevier B.V. and ECNP. All rights reserved.

Dry matter intake and digestibility of rations replacing concentrates with graded levels of Enterolobium cyclocarpum in Pelibuey lambs.

PubMed

Piñeiro-Vázquez, Angel Trinidad; Ayala-Burgos, Armín Javier; Chay-Canul, Alfonso Juventino; Ku-Vera, Juan Carlos

2013-02-01

The aim of the study was to evaluate the effect of graded levels of Enterolobium cyclocarpum pods in the ration on feed intake and digestibility by Pelibuey lambs. Five dietary treatments were imposed where ground pods replaced concentrate diet at 0, 20, 30, 40 and 50 % of dry matter (DM), respectively. The concentrate portion was composed of ground sorghum, soybean meal, cane molasses and minerals. Five entire Pelibuey lambs with initial bodyweight 34 ± 2 kg were allocated in the treatments in a 5 × 5 Latin square design. Values of dry matter intake (DMI) and dry matter (DMD) and organic matter (OMD) digestibility were measured and metabolisable energy intake (MEI) estimated. Rumen degradation constants for E. cyclocarpum were also measured. There were no differences (P > 0.05) in average DMI (86.6 g/kg(0.75)) and OMI (81.2 g/kg(0.75)) among treatments. As the level of incorporation of E. cyclocarpum pods increased, voluntary DMI and OMI increased, whereas apparent DMD and OMD decreased linearly. Average digestible DM (65 g/kg(0.75)) and OM (61 g/kg(0.75)) intakes were similar (P > 0.05) among treatments. Similarly, MEI (0.976 MJ ME kg(0.75)/day) was not different (P > 0.05) among treatments. The potential rumen degradation (A + B) of ground pods of E. cyclocarpum was 866.4 g/kg DM. Ground pods of E. cyclocarpum can be employed for lamb feeding up to 50 % of the ration, without affecting DMI, DM apparent digestibility and MEI.

Field-free deterministic ultrafast creation of magnetic skyrmions by spin-orbit torques

NASA Astrophysics Data System (ADS)

Büttner, Felix; Lemesh, Ivan; Schneider, Michael; Pfau, Bastian; Günther, Christian M.; Hessing, Piet; Geilhufe, Jan; Caretta, Lucas; Engel, Dieter; Krüger, Benjamin; Viefhaus, Jens; Eisebitt, Stefan; Beach, Geoffrey S. D.

2017-11-01

Magnetic skyrmions are stabilized by a combination of external magnetic fields, stray field energies, higher-order exchange interactions and the Dzyaloshinskii-Moriya interaction (DMI). The last favours homochiral skyrmions, whose motion is driven by spin-orbit torques and is deterministic, which makes systems with a large DMI relevant for applications. Asymmetric multilayers of non-magnetic heavy metals with strong spin-orbit interactions and transition-metal ferromagnetic layers provide a large and tunable DMI. Also, the non-magnetic heavy metal layer can inject a vertical spin current with transverse spin polarization into the ferromagnetic layer via the spin Hall effect. This leads to torques that can be used to switch the magnetization completely in out-of-plane magnetized ferromagnetic elements, but the switching is deterministic only in the presence of a symmetry-breaking in-plane field. Although spin-orbit torques led to domain nucleation in continuous films and to stochastic nucleation of skyrmions in magnetic tracks, no practical means to create individual skyrmions controllably in an integrated device design at a selected position has been reported yet. Here we demonstrate that sub-nanosecond spin-orbit torque pulses can generate single skyrmions at custom-defined positions in a magnetic racetrack deterministically using the same current path as used for the shifting operation. The effect of the DMI implies that no external in-plane magnetic fields are needed for this aim. This implementation exploits a defect, such as a constriction in the magnetic track, that can serve as a skyrmion generator. The concept is applicable to any track geometry, including three-dimensional designs.

Evaluation of wheat-based thin stillage as a water source for growing and finishing beef cattle.

PubMed

Fisher, D J; McKinnon, J J; Mustafa, A F; Christensen, D A; McCartney, D

1999-10-01

Two trials were conducted to evaluate the nutritional value of wheat-based thin stillage as a water source for cattle. In Trial 1, 20 large-framed steers were fed a basal diet based primarily on barley grain and barley silage, with ad libitum access to water or thin stillage at one of three DM concentrations (2, 4, and 6.7%) in a completely randomized design. The trial consisted of a 70-d growing period and a finishing phase. In Trial 2, total-tract nutrient digestibility coefficients of the basal diet and water treatments fed in the growing period were determined in a randomized complete block design using 12 medium-framed steers. The results showed that when only DMI from the basal diet was considered, there was a linear reduction (P<.01) in DMI and a linear improvement (P<.01) in the gain:feed ratio with no effect on daily gain as thin stillage DM concentration increased. No differences were detected in DMI or efficiency of gain when total DMI (basal diet and thin stillage) was considered. Carcass traits indicated a trend toward increased (P<.06) carcass fat with increasing thin stillage DM concentration. Results of Trial 2 indicated a linear improvement (P<.05) in apparent digestibility of DM, CP, NDF, and energy of the total diet (basal diet and thin stillage) as thin stillage DM concentration increased. We concluded that supplementing growing and finishing cattle with thin stillage reduced the amount of the basal diet required for gain and improved nutrient utilization.

Extinction-induced "despair" in the water maze, exploratory behavior and fear: effects of chronic antidepressant treatment.

PubMed

Schulz, Daniela; Buddenberg, Tim; Huston, Joseph P

2007-05-01

In former studies, we found evidence for the hypothesis that withdrawal of negative reinforcement presents a major source for stress and despair. Specifically, the removal of a hidden platform in the water maze induced extinction of previously reinforced escape behavior and behavioral immobility, indicative of "despair", which also correlated with indices of fear. Here, we tested the effects of antidepressants on extinction in the water maze, and expected that such drugs would attenuate the rate of extinction of a conditioned place preference (CPP) and also any emotionally relevant behavior that is induced by the loss of reinforcement, such as immobility. Adult male Wistar rats were trained to escape onto a hidden platform for 10 days. Daily treatment with desipramine hydrochloride (DMI, 10mg/kg) or fluoxetine (FLX, 10 mg/kg) commenced 1 day before the first of 11 extinction trials without the platform, administered 48 h apart, and continued thereafter, as the rats were tested in an open field and elevated-plus maze. As compared to controls, DMI increased the resistance-to-extinction of CPP, attenuated immobility, and increased wall climbing behavior. In the open field, DMI reduced activity levels, but was without effect on traditional fear parameters in the elevated-plus maze. FLX, by contrast, increased immobility during the extinction trials and fear in the elevated-plus maze. The withdrawal of reinforcement induced "despair" that was alleviated by the noradrenaline reuptake inhibitor DMI. The effects of the selective serotonin reuptake inhibitor FLX on immobility and fear may be explained in terms of its side effect profile.

Prediction of enteric methane production, yield, and intensity in dairy cattle using an intercontinental database.

PubMed

Niu, Mutian; Kebreab, Ermias; Hristov, Alexander N; Oh, Joonpyo; Arndt, Claudia; Bannink, André; Bayat, Ali R; Brito, André F; Boland, Tommy; Casper, David; Crompton, Les A; Dijkstra, Jan; Eugène, Maguy A; Garnsworthy, Phil C; Haque, Md Najmul; Hellwing, Anne L F; Huhtanen, Pekka; Kreuzer, Michael; Kuhla, Bjoern; Lund, Peter; Madsen, Jørgen; Martin, Cécile; McClelland, Shelby C; McGee, Mark; Moate, Peter J; Muetzel, Stefan; Muñoz, Camila; O'Kiely, Padraig; Peiren, Nico; Reynolds, Christopher K; Schwarm, Angela; Shingfield, Kevin J; Storlien, Tonje M; Weisbjerg, Martin R; Yáñez-Ruiz, David R; Yu, Zhongtang

2018-02-16

Enteric methane (CH 4 ) production from cattle contributes to global greenhouse gas emissions. Measurement of enteric CH 4 is complex, expensive, and impractical at large scales; therefore, models are commonly used to predict CH 4 production. However, building robust prediction models requires extensive data from animals under different management systems worldwide. The objectives of this study were to (1) collate a global database of enteric CH 4 production from individual lactating dairy cattle; (2) determine the availability of key variables for predicting enteric CH 4 production (g/day per cow), yield [g/kg dry matter intake (DMI)], and intensity (g/kg energy corrected milk) and their respective relationships; (3) develop intercontinental and regional models and cross-validate their performance; and (4) assess the trade-off between availability of on-farm inputs and CH 4 prediction accuracy. The intercontinental database covered Europe (EU), the United States (US), and Australia (AU). A sequential approach was taken by incrementally adding key variables to develop models with increasing complexity. Methane emissions were predicted by fitting linear mixed models. Within model categories, an intercontinental model with the most available independent variables performed best with root mean square prediction error (RMSPE) as a percentage of mean observed value of 16.6%, 14.7%, and 19.8% for intercontinental, EU, and United States regions, respectively. Less complex models requiring only DMI had predictive ability comparable to complex models. Enteric CH 4 production, yield, and intensity prediction models developed on an intercontinental basis had similar performance across regions, however, intercepts and slopes were different with implications for prediction. Revised CH 4 emission conversion factors for specific regions are required to improve CH 4 production estimates in national inventories. In conclusion, information on DMI is required for good prediction, and other factors such as dietary neutral detergent fiber (NDF) concentration, improve the prediction. For enteric CH 4 yield and intensity prediction, information on milk yield and composition is required for better estimation. © 2018 John Wiley & Sons Ltd.

An Automated Thermocouple Calibration System

NASA Technical Reports Server (NTRS)

Bethea, Mark D.; Rosenthal, Bruce N.

1992-01-01

An Automated Thermocouple Calibration System (ATCS) was developed for the unattended calibration of type K thermocouples. This system operates from room temperature to 650 C and has been used for calibration of thermocouples in an eight-zone furnace system which may employ as many as 60 thermocouples simultaneously. It is highly efficient, allowing for the calibration of large numbers of thermocouples in significantly less time than required for manual calibrations. The system consists of a personal computer, a data acquisition/control unit, and a laboratory calibration furnace. The calibration furnace is a microprocessor-controlled multipurpose temperature calibrator with an accuracy of +/- 0.7 C. The accuracy of the calibration furnace is traceable to the National Institute of Standards and Technology (NIST). The computer software is menu-based to give the user flexibility and ease of use. The user needs no programming experience to operate the systems. This system was specifically developed for use in the Microgravity Materials Science Laboratory (MMSL) at the NASA LeRC.

Optimal design approach for heating irregular-shaped objects in three-dimensional radiant furnaces using a hybrid genetic algorithm-artificial neural network method

NASA Astrophysics Data System (ADS)

Darvishvand, Leila; Kamkari, Babak; Kowsary, Farshad

2018-03-01

In this article, a new hybrid method based on the combination of the genetic algorithm (GA) and artificial neural network (ANN) is developed to optimize the design of three-dimensional (3-D) radiant furnaces. A 3-D irregular shape design body (DB) heated inside a 3-D radiant furnace is considered as a case study. The uniform thermal conditions on the DB surfaces are obtained by minimizing an objective function. An ANN is developed to predict the objective function value which is trained through the data produced by applying the Monte Carlo method. The trained ANN is used in conjunction with the GA to find the optimal design variables. The results show that the computational time using the GA-ANN approach is significantly less than that of the conventional method. It is concluded that the integration of the ANN with GA is an efficient technique for optimization of the radiant furnaces.

Prediction of enteric methane emissions from sheep offered fresh perennial ryegrass () using data measured in indirect open-circuit respiration chambers.

PubMed

Zhao, Y G; O'Connell, N E; Yan, T

2016-06-01

Development of effective methane (CH) mitigation strategies for grazing sheep requires accurate prediction tools. The present study aimed to identify key parameters influencing enteric CH emissions and develop prediction equations for enteric CH emissions from sheep offered fresh grass. The data used were collected from 82 sheep offered fresh perennial ryegrass () as sole diets in 6 metabolism experiments (data from non-grass-only diets were not used). Sheep were from breeds of Highlander, Texel, Scottish Blackface, and Swaledale at the age of 5 to 18 mo and weighing from 24.5 to 62.7 kg. Grass was harvested daily from 6 swards on contrasting harvest dates (May to December). Before the commencement of each study, the experimental sward was harvested at a residual height of 4 cm and allowed to grow for 2 to 4 wk. The feeding trials commenced when the grass sward was suitable to zero grazing (average grass height = 15 cm), thus offering grass of a quality similar to what grazing animals would receive under routine grazing management. Sheep were housed in individual pens for 14 d and then moved to individual calorimeter chambers for 4 d. Feed intake, fecal and urine outputs, and CH emissions were measured during the final 4 d. Data were analyzed using the REML procedure to develop prediction equations for CH emissions. Linear and multiple prediction equations were developed using BW, DMI, GE intake (GEI), and grass chemical concentrations (DM, OM, water-soluble carbohydrates [WSC], NDF, ADF, nitrogen [N], GE, DE, and ME) as explanatory variables. The mean CH production was 21.1 g/kg DMI or 0.062 MJ/MJ GEI. Dry matter intake and GEI were much more accurate predictors for CH emissions than BW ( < 0.001, = 0.86 and = 0.87 vs. = 0.09, respectively). Adding grass DE and ME concentrations and grass nutrient concentrations (e.g., OM, N, GE, NDF, and WSC) to the relationships between DMI or GEI and CH emissions improved prediction accuracy with values increased to 0.93. Models based on farm-level data, for example, BW and grass nutrient (i.e., DM, GE, OM, and N) concentrations, were also developed and performed satisfactorily ( < 0.001, = 0.63). These models can contribute to improve prediction accuracy for enteric CH emissions from sheep grazing on ryegrass pasture.

Separation of polysaccharides from rice husk and wheat bran using solvent system consisting of BMIMOAc and DMI.

PubMed

Hou, Qidong; Li, Weizun; Ju, Meiting; Liu, Le; Chen, Yu; Yang, Qian; Wang, Jingyu

2015-11-20

A solvent system consisting of 1,3-dimethyl-2-imidazolidinone (DMI), and ionic liquid 1-butyl-3-methylimidazolium acetate (BMIMOAc) was used to separate polysaccharides from rice husk and wheat bran. The effects of the DMI/BMIMOAc ratios, temperature, and time on the dissolution of rice husk and wheat bran were investigated, and the influence of anti-solvents on the regeneration of polysaccharides-rich material was evaluated. We found that the solvent system is more powerful to dissolve rice husk and wheat bran than pure BMIMOAc, and that polysaccharides-rich material can be effectively separated from the biomass solution. The polysaccharides content of regenerated material from wheat bran can reach as high as 94.4% when ethanol was used as anti-solvents. Under optimized conditions, the extraction rate of polysaccharides for wheat bran can reach as high as 71.8% at merely 50°C. The recycled solvent system exhibited constant ability to separate polysaccharides from rice husk and wheat bran. Copyright © 2015 Elsevier Ltd. All rights reserved.

Domain-wall motion at an ultrahigh speed driven by spin-orbit torque in synthetic antiferromagnets.

PubMed

Yu, Ziyang; Zhang, Yue; Zhang, Zhenhua; Cheng, Ming; Lu, Zhihong; Yang, Xiaofei; Shi, Jing; Xiong, Rui

2018-04-27

In this article, we present our numerical investigation about the spin-orbit-torque induced domain-wall (DW) motion in a synthetic antiferromagnetic multilayer nanotrack. This nanotrack was composed by two ferromagnetic (FM) layers with a RKKY inter-layer antiferromagnetic (AFM) exchange coupling. The velocity of DW was well manipulated by varying parameters including inter-layer exchange constant, the Dzyaloshinskii-Moriya interaction (DMI) strength, the current density and the magnetic anisotropy. The DW velocity was found to be strictly related to the orientation of the moments in the two FM layers. When the interlayer exchange constant or the DMI constant were larger than a critical value, there was a large angle between the moments in one FM layer and that in the other one under the current, and the DW was driven to move at an ultrahigh speed (around 10 000 m s -1 ). However, when the DMI or the AFM exchange coupling was weaker than the critical value, the moments in one FM layer were parallel to that in the other one under the current, and the velocity was significantly reduced.

SUBSA and PFMI Transparent Furnace Systems Currently in use in the International Space Station Microgravity Science Glovebox

NASA Technical Reports Server (NTRS)

Spivey, Reggie A.; Gilley, Scott; Ostrogorsky, Aleksander; Grugel, Richard; Smith, Guy; Luz, Paul

2003-01-01

The Solidification Using a Baffle in Sealed Ampoules (SUBSA) and Pore Formation and Mobility Investigation (PFMI) furnaces were developed for operation in the International Space Station (ISS) Microgravity Science Glovebox (MSG). Both furnaces were launched to the ISS on STS-111, June 4, 2002, and are currently in use on orbit. The SUBSA furnace provides a maximum temperature of 850 C and can accommodate a metal sample as large as 30 cm long and 12mm in diameter. SUBSA utilizes a gradient freeze process with a minimum cooldown rate of 0.5C per min, and a stability of +/- 0.15C. An 8 cm long transparent gradient zone coupled with a Cohu 3812 camera and quartz ampoule allows for observation and video recording of the solidification process. PFMI is a Bridgman type furnace that operates at a maximum temperature of 130C and can accommodate a sample 23cm long and 10mm in diameter. Two Cohu 3812 cameras mounted 90 deg apart move on a separate translation system which allows for viewing of the sample in the transparent hot zone and gradient zone independent of the furnace translation rate and direction. Translation rates for both the cameras and furnace can be specified from 0.5micrometers/sec to 100 micrometers/sec with a stability of +/-5%. The two furnaces share a Process Control Module (PCM) which controls the furnace hardware, a Data Acquisition Pad (DaqPad) which provides signal condition of thermal couple data, and two Cohu 3812 cameras. The hardware and software allow for real time monitoring and commanding of critical process control parameters. This paper will provide a detailed explanation of the SUBSA and PFMI systems along with performance data and some preliminary results from completed on-orbit processing runs.

Variations in automatically recorded rumination time as explained by variations in intake of dietary fractions and milk production, and between-cow variation.

PubMed

Byskov, M V; Nadeau, E; Johansson, B E O; Nørgaard, P

2015-06-01

Individual recording of rumination time (RT) is now possible in commercial dairy herds, through development of a microphone-based sensor, which is able to record RT by the sound of rumination activity. The objectives of this study were to examine the relationship between daily RT and intakes of different dietary fractions, the relationship between RT in minutes per kilogram of dry matter intake (DMI) and milk production, and to examine the variation in RT within and between mid-lactating dairy cows. Data from 3 production trials were used in which a total of 27 different diets were fed. The data contained 761, 290, and 203 daily recordings of RT, milk yield, milk components, DMI, and intake of dietary fractions recorded on 29, 26, and 24 Holstein and Swedish Red cows from trials 1, 2, and 3, respectively. The dietary fractions included forage neutral detergent fiber (NDF), concentrate NDF, crude protein, sugar, starch, and the remaining fraction represented by organic matter--(forage NDF+concentrate NDF+crude protein+sugar+starch). The relationship between the dietary fractions and RT was analyzed in 2 steps. In step 1, the dietary fractions, which were significantly related to RT, were selected and simultaneously checked for multicollinearity between the dietary components; in step 2, a multivariate model, including the effect of repeated measurements, the main effect of the selected dietary fractions from step 1, random effects of cow(trial) and trial, and information on breed, days in milk, and parity was used to analyze the relationship between RT and the selected dietary fractions. Relationships between RT in minutes per kilogram of DMI and milk yield and milk components were analyzed, using the same multivariate model as in step 2. Approximately 32% of the variation in daily RT could be explained by variations in intakes of the dietary fractions, whereas 48% of the total variation in RT was accounted for by individual variations between cows. Intakes of forage NDF and starch were positively related to daily RT, whereas intakes of sugar and the remaining fraction were negatively related to daily RT. Rumination time in minutes per kilogram of DMI was negatively related to milk yield and protein percentage, but positively related to milk fat percentage. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Weather influences feed intake and feed efficiency in a temperate climate.

PubMed

Hill, Davina L; Wall, Eileen

2017-03-01

A key goal for livestock science is to ensure that food production meets the needs of an increasing global population. Climate change may heighten this challenge through increases in mean temperatures and in the intensity, duration, and spatial distribution of extreme weather events, such as heat waves. Under high ambient temperatures, livestock are expected to decrease dry matter intake (DMI) to reduce their metabolic heat production. High yielding dairy cows require high DMI to support their levels of milk production, but this may increase susceptibility to heat stress. Here, we tested how feed intake and the rate of converting dry matter to milk (feed efficiency, FE) vary in response to natural fluctuations in weather conditions in a housed experimental herd of lactating Holstein Friesians in the United Kingdom. Cows belonged to 2 lines: those selected for high genetic merit for milk traits (select) and those at the UK average (control). We predicted that (1) feed intake and FE would vary with an index of temperature and humidity (THI), wind speed, and the number of hours of sunshine, and that (2) the effects of (1) would depend on the cows' genetic merit. Animals received a mixed ration, available ad libitum, from automatic feed measurement gates. Using >73,000 daily feed intake and FE records from 328 cows over 8 yr, we found that select cows produced more fat- and protein-corrected milk, and had higher DMI and FE than controls. Cows of both lines decreased DMI and fat- and protein-corrected milk but, importantly, increased FE as THI increased. This suggests that improvements in the efficiency of converting feed to milk may partially offset the costs of reduced milk yield owing to a warmer climate, at least under conditions of mild heat stress. The rate of increase in FE with THI was steeper in select cows than in controls, which raises the possibility that select cows use more effective coping tactics. This is, to our knowledge, the first longitudinal study on the effects of weather on FE. Understanding how weather influences feed intake and efficiency can help us to develop management and selection practices that optimize productivity under unfavorable weather conditions. This will be an important aspect of climate resilience in future. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effect of ambient temperature and sodium bicarbonate supplementation on water and electrolyte balances in dry and lactating Holstein cows.

PubMed

Khelil-Arfa, H; Faverdin, P; Boudon, A

2014-01-01

The aim of this study was to quantify the effect of the interaction between 2 constant ambient temperatures [thermoneutrality (TN; 15°C) and high temperature (HT; 28°C)] and 2 levels of Na bicarbonate supplementation [calculated to provide diet Na contents of 0.20%DM (Na-) and 0.50%DM (Na+)] on water partitioning in dairy cows. Treatments were compared on 4 dry and 4mid-lactation Holstein cows according to 2 Latin squares (1 for each physiological stage) over the course of 4 periods of 15d. Diets consisted of a total mixed ration based on maize silage. Dry cows were restricted to their protein and energy requirements, whereas lactating cows were fed ad libitum. The daily average temperature-humidity index was 59.4 for TN and 73.2 for HT. Lactating and dry cows had higher vaginal temperatures at HT than at TN, but the increase was more pronounced in lactating cows (+1.05 vs. +0.12°C for vaginal temperature, respectively). Dry matter intake (DMI) of lactating cows decreased by 2.3kg/d at HT. Free water intake (FWI) and estimated volume of water lost to evaporation increased at HT in both lactating and dry cows; no interactions were observed between temperature and physiological stage. When expressed as a proportion of DMI, the increase in evaporation that occurred with increasing temperature was completely compensated for by an increase in FWI for both physiological stages. The urinary water excretion increased slightly at HT in lactating cows but not in dry cows, which may be related to the low chloride content of the offered diet. High Na supplementation increased DMI slightly in lactating cows, but milk yield was not affected. Sodium supplementation did not limit the decrease in DMI observed in lactating cows at HT; this observation is likely due to the high diet electrolyte balance of the offered diets. Sodium supplementation increased FWI in lactating cows and urinary flow in both physiological states. The interaction between ambient temperature and Na supplementation did not affect either water intake or water evaporation. This study demonstrates that the development of predictive models for water intake that include environmental variables could be based on mechanistic models of evaporation. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

SITE DEMONSTRATION OF MINERGY GLASS FURNACE TREATMENT OF PCBS, PCDDS/FS, AND METALS IN RIVER SEDIMENT

EPA Science Inventory

The U.S. Environmental Protection Agency (EPA) Superfund Innovative Technology Evaluation (SITE) program selected the Glass Furnace Technology (GFT) treatment process for evaluation. The GFT was developed by Minergy Corporation (Minergy) as an ex situ remediation technolog...

Glass shell manufacturing in space

NASA Technical Reports Server (NTRS)

Downs, R. L.; Ebner, M. A.; Nolen, R. L., Jr.

1981-01-01

Highly-uniform, hollow glass spheres (shells), which are used for inertial confinement fusion targets, were formed from metal-organic gel powder feedstock in a vertical furnace. As a result of the rapid pyrolysis caused by the furnace, the gel is transformed to a shell in five distinct stages: (a) surface closure of the porous gel; (b) generation of a closed-cell foam structure in the gel; (c) spheridization of the gel and further expansion of the foam; (d) coalescence of the closed-cell foam to a single-void shell; and (e) fining of the glass shell. The heat transfer from the furnace to the falling gel particle was modeled to determine the effective heating rate of the gel. The model predicts the temperature history for a particle as a function of mass, dimensions, specific heat, and absorptance as well as furnace temperature profile and thermal conductivity of the furnace gas. A model was developed that predicts the gravity-induced degradation of shell concentricity in falling molten shells as a function of shell characteristics and time.

Crystal growth and furnace analysis

NASA Technical Reports Server (NTRS)

Dakhoul, Youssef M.

1986-01-01

A thermal analysis of Hg/Cd/Te solidification in a Bridgman cell is made using Continuum's VAST code. The energy equation is solved in an axisymmetric, quasi-steady domain for both the molten and solid alloy regions. Alloy composition is calculated by a simplified one-dimensional model to estimate its effect on melt thermal conductivity and, consequently, on the temperature field within the cell. Solidification is assumed to occur at a fixed temperature of 979 K. Simplified boundary conditions are included to model both the radiant and conductive heat exchange between the furnace walls and the alloy. Calculations are performed to show how the steady-state isotherms are affected by: the hot and cold furnace temperatures, boundary condition parameters, and the growth rate which affects the calculated alloy's composition. The Advanced Automatic Directional Solidification Furnace (AADSF), developed by NASA, is also thermally analyzed using the CINDA code. The objective is to determine the performance and the overall power requirements for different furnace designs.

Measurements of alkali concentrations in an oxygen-natural gas-fired soda-lime-silica glass furnace

DOE Office of Scientific and Technical Information (OSTI.GOV)

S. G. Buckley; P. M. Walsh; D. w. Hahn

1999-10-18

Sodium species vaporized from melting batch and molten glass in tank furnaces are the principal agents of corrosion of superstructure refractory and main contributors to emissions of particulate matter from glass melting. The use of oxygen in place of air for combustion of natural gas reduces particulate emissions, but is thought to accelerate corrosion in some melting tanks. Methods for measuring sodium are under investigation as means for identifying the volatilization, transport, and deposition mechanisms and developing strategies for control. Three separate methods were used to measure the concentrations of sodium species at various locations in an oxygen-natural gas-fired soda-lime-silicamore » glass melting tank. Measurements were made inside the furnace using the absorption of visible light and in the flue duct using Laser-Induced Breakdown Spectroscopy (LIBS). Measurements in both the furnace and flue were also made by withdrawing and analyzing samples of the furnace gas.« less

Numerical Simulation and Chaotic Analysis of an Aluminum Holding Furnace

NASA Astrophysics Data System (ADS)

Wang, Ji-min; Zhou, Yuan-yuan; Lan, Shen; Chen, Tao; Li, Jie; Yan, Hong-jie; Zhou, Jie-min; Tian, Rui-jiao; Tu, Yan-wu; Li, Wen-ke

2014-12-01

To achieve high heat efficiency, low pollutant emission and homogeneous melt temperature during thermal process of secondary aluminum, taking into account the features of aluminum alloying process, a CFD process model was developed and integrated with heat load and aluminum temperature control model. This paper presented numerical simulation of aluminum holding furnaces using the customized code based on FLUENT packages. Thermal behaviors of aluminum holding furnaces were investigated by probing into main physical fields such as flue gas temperature, velocity, and concentration, and combustion instability of aluminum holding process was represented by chaos theory. The results show that aluminum temperature uniform coefficient firstly decreases during heating phase, then increases and reduces alternately during holding phase, lastly rises during standing phase. Correlation dimension drops with fuel velocity. Maximal Lyapunov exponent reaches to a maximum when air-fuel ratio is close to 1. It would be a clear comprehension about each phase of aluminum holding furnaces to find new technology, retrofit furnace design, and optimize parameters combination.

Effect of supplemental nutrient source on heifer growth and reproductive performance, and on utilization of corn silage-based diets by beef steers.

PubMed

Howlett, C M; Vanzant, E S; Anderson, L H; Burris, W R; Fieser, B G; Bapst, R F

2003-09-01

Two experiments were conducted to determine effects of oilseeds or soybean hulls on growth and reproductive performance of heifers and utilization of corn silage diets by growing beef cattle. In Exp. 1, 96 beef heifers (249 kg of BW) were used in a randomized complete block design. Treatments were as follows: 1) corn and soybean meal (CON) at 56% of the DMI; 2) whole linted cottonseed at 15% of the DMI (COT); 3) whole raw soybeans at 15% of the DMI (SB); or 4) pelleted soyhulls at 30% of the DMI (SH). Diets were formulated to be isonitrogenous (13.8% CP) and fed to achieve target weights equal to 65% of expected mature BW at the time of AI. Estrus was synchronized and heifers were inseminated by AI in response to detected estrus. Because the energy value for SH was underestimated, cumulative ADG for SH (1.03 kg/d) was greater (P < or = 0.03) than for CON (0.89 kg/d), COT (0.87 kg/d), or SB (0.86 kg/d). Treatment did not affect (P > 0.10) the proportion of pubertal heifers at the beginning of the breeding season: CON (60%), COT (53%), SB (69%), SH (71%), or first-service conception rates: CON (37%); COT (38%); SB (57%); SH (42%). In Exp. 2, crossbred steers (387 kg) were used in a 6 x 6 Latin square design to evaluate the effects of supplemental nutrient source on utilization of corn silage diets. Treatments included diets used in Exp. 1, plus a negative control (soybean meal at 10% of the DMI; SIL) and whole raw soybeans at 25% of the DMI (SB25). Diets were formulated to be isonitrogenous (13.8% CP) except SB25 (17% CP), and were fed twice daily at 1.8 x NEm. Oilseed inclusion decreased (P < 0.10) acetate:propionate ratios and (P < 0.10) apparent ruminal OM and ruminal and total tract NDF digestibilities. The CON and SH diets had the greatest (P < 0.10) total-tract OM digestibilities. Microbial efficiencies were greatest (P < 0.10), and long chain fatty acid flow to the duodenum increased (P < 0.10) with oilseeds. Biohydrogenation averaged 90.4% and increased slightly (P < 0.10) when oilseeds were added to the diet. Adding oilseeds or soybean hulls to corn silage-based diets did not affect reproductive performance of heifers. Although oilseed additions increased total fatty acid flow to the duodenum, a high degree of biohydrogenation occurred, greatly increasing C18:0, with only marginal increases in unsaturated fatty acid flow. Depending on diet and feeding conditions, inclusion of whole oilseeds may not be an effective means of increasing linoleic acid supply for ruminant animals.

Information modeling system for blast furnace control

NASA Astrophysics Data System (ADS)

Spirin, N. A.; Gileva, L. Y.; Lavrov, V. V.

2016-09-01

Modern Iron & Steel Works as a rule are equipped with powerful distributed control systems (DCS) and databases. Implementation of DSC system solves the problem of storage, control, protection, entry, editing and retrieving of information as well as generation of required reporting data. The most advanced and promising approach is to use decision support information technologies based on a complex of mathematical models. The model decision support system for control of blast furnace smelting is designed and operated. The basis of the model system is a complex of mathematical models created using the principle of natural mathematical modeling. This principle provides for construction of mathematical models of two levels. The first level model is a basic state model which makes it possible to assess the vector of system parameters using field data and blast furnace operation results. It is also used to calculate the adjustment (adaptation) coefficients of the predictive block of the system. The second-level model is a predictive model designed to assess the design parameters of the blast furnace process when there are changes in melting conditions relative to its current state. Tasks for which software is developed are described. Characteristics of the main subsystems of the blast furnace process as an object of modeling and control - thermal state of the furnace, blast, gas dynamic and slag conditions of blast furnace smelting - are presented.

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.K. Kawatra; B. Anamerie; T.C. Eisele

The pig iron nugget process was developed as an alternative to the traditional blast furnace process by Kobe Steel. The process aimed to produce pig iron nuggets, which have similar chemical and physical properties to blast furnace pig iron, in a single step. The pig iron nugget process utilizes coal instead of coke and self reducing and fluxing dried green balls instead of pellets and sinters. In this process the environmental emissions caused by coke and sinter production, and energy lost between pellet induration (heat hardening) and transportation to the blast furnace can be eliminated. The objectives of this researchmore » were to (1) produce pig iron nuggets in the laboratory, (2) characterize the pig iron nugget produced and compare them with blast furnace pig iron, (3) investigate the furnace temperature and residence time effects on the pig iron nugget production, and (4) optimize the operational furnace temperatures and residence times. The experiments involved heat treatment of self reducing and fluxing dried green balls at various furnace temperatures and residence times. Three chemically and physically different products were produced after the compete reduction of iron oxides to iron depending on the operational furnace temperatures and/or residence times. These products were direct reduced iron (DRI), transition direct reduced iron (TDRI), and pig iron nuggets. The increase in the carbon content of the system as a function of furnace temperature and/or residence time dictated the formation of these products. The direct reduced iron, transition direct reduced iron, and pig iron nuggets produced were analyzed for their chemical composition, degree of metallization, apparent density, microstructure and microhardness. In addition, the change in the carbon content of the system with the changing furnace temperature and/or residence time was detected by optical microscopy and Microhardness measurements. The sufficient carbon dissolution required for the production of pig iron nuggets was determined. It was determined that pig iron nuggets produced had a high apparent density (6.7-7.2 gr/cm3), highly metallized, slag free structure, high iron content (95-97%), high microhardness values (> 325 HVN) and microstructure similar to white cast iron. These properties made them a competitive alternative to blast furnace pig iron.« less

Acoustic levitation for high temperature containerless processing in space

NASA Technical Reports Server (NTRS)

Rey, C. A.; Sisler, R.; Merkley, D. R.; Danley, T. J.

1990-01-01

New facilities for high-temperature containerless processing in space are described, including the acoustic levitation furnace (ALF), the high-temperature acoustic levitator (HAL), and the high-pressure acoustic levitator (HPAL). In the current ALF development, the maximum temperature capabilities of the levitation furnaces are 1750 C, and in the HAL development with a cold wall furnace they will exceed 2000-2500 C. The HPAL demonstrated feasibility of precursor space flight experiments on the ground in a 1 g pressurized-gas environment. Testing of lower density materials up to 1300 C has also been accomplished. It is suggested that advances in acoustic levitation techniques will result in the production of new materials such as ceramics, alloys, and optical and electronic materials.

HEU Holdup Measurements in 321-M B and Spare U-Al Casting Furnaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Salaymeh, S.R.

The Analytical Development Section of Savannah River Technology Center (SRTC) was requested by the Facilities Decontamination Division (FDD) to determine the holdup of enriched uranium in the 321-M facility as part of an overall deactivation project of the facility. The 321-M facility was used to fabricate enriched uranium fuel assemblies, lithium-aluminum target tubes, neptunium assemblies, and miscellaneous components for the production reactors. This report covers holdup measurements in two uranium aluminum alloy (U-Al) casting furnaces. Our results indicate an upper limit of 235U content for the B and Spare furnaces of 51 and 67 g respectively. This report discusses themore » methodology, non-destructive assay (NDA) measurements, and results of the uranium holdup on the two furnaces.« less

Development of a high-performance coal-fired power generating system with pyrolysis gas and char-fired high temperature furnace (HITAF). Quarterly progress report No. 6, April--June 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1993-08-01

A concept for an advanced coal-fired combined-cycle power generating system is currently being developed. The first phase of this three-phase program consists of conducting the necessary research and development to define the system, evaluating the economic and technical feasibility of the concept, and preparing an R&D plan to develop the concept further. The system proposed to meet these goals is a combined-cycle system where air for a gas turbine is indirectly heated to approximately 1800{degree}F in furnaces fired with coal-derived fuels and then directly heated in a natural-gas-fired combustor to about 2400{degree}F. The system is based on a pyrolyzing processmore » that converts the coal into a low-Btu fuel gas and char. The fuel gas is relatively clean, and it is fired to heat tube surfaces that are susceptible to corrosion and problems from ash deposition. In particular, the high-temperature air heater tubes, which will need to be a ceramic material, will be located in a separate furnace or region of a furnace that is exposed to combustion products from the low-Btu fuel gas only.« less

BUNDLE: A Novel Furnace for Performing Controlled Directional Solidification Experiments in a Microgravity Environment

NASA Technical Reports Server (NTRS)

Carrasquillo, Edgar J.; Griffin, Mark R.; Hammond, Monica S.; Johnson, Martin L.; Grugel, R. N.

2000-01-01

NASA Marshall Space Flight Center has developed a novel directional solidification furnace prototype for processing metals and alloys experiments in a microgravity environment. The BUNDLE (Bridgman Unidirectional Dendrite in Liquid Experiment) furnace is intended to accommodate the science requirements of Flight Definition Principle Investigators studying cellular/dendritic growth in aluminum and lead alloys at processing temperatures up to 1200 C. The furnace implements a number of innovative features to achieve high thermal gradients and quench rates in a low-power, light-weight design. These include a pyrolytic boron nitride/graphite composite heating element surrounded by layers of self-supporting refractory metal shielding, and a graphite fiber enhanced cold zone allowing high levels of heat extraction from the sample crucible. Novel to the BUNDLE design is an in-situ helium gas quench capability that ensures rapid freezing of the solidifying region (mushy zone) of the metal sample within the furnace without sample disturbance prior to quenching; this is a stringent requirement for subsequent analysis and understanding of microstructural development. The experiment hardware concept features multiple furnaces that may be "bundled" together so many samples, currently up to eight, can be processed at one time. The design of BUNDLE is flexible enough to be implemented on the Shuttle and Space Station in a number of locations (SpaceHab, Express Rack, MPESS, ISPR, etc). BUNDLE prototype furnaces have directionally solidified and quenched 1cm diameter lead - 5.8 weight percent antimony and aluminum - 4 weight percent copper alloys. Quenching of the mushy zone, as recorded by in-situ thermocouples, occurred on the order of 0.5 seconds or less, a rate within the PI's requirements. Subsequent metallographic examination revealed the solidified microstructure to be, as expected, unidirectional. Both the dendrite tips and the eutectic reaction were planar in nature indicating uniform axial heat flow. Delineation between the growing dendrites and eutectic structure with the "quenched-in" liquid was sharp, attesting to the efficacy of the helium quench. BUNDLE's conception, development, capability, and adaptability are presented (in view of Flight PI's needs and science requirements) through viewgraphs depicting actual hardware, generated thermal analysis, and micrographs prepared from BUNDLE processed, flight-like samples.

BUNDLE - A Novel Furnace for Performing Controlled Directional Solidification Experiments in a Microgravity Environment

NASA Technical Reports Server (NTRS)

Carrasquillo, Edgar J.; Griffin, Mark R.; Hammond, Monica S.; Johnson, Martin L.; Grugel, R. N.

2001-01-01

NASA Marshall Space Flight Center has developed a novel directional solidification furnace prototype for processing metals and alloys experiments in a microgravity environment. The BUNDLE (Bridgman Unidirectional Dendrite in Liquid Experiment) furnace is intended to accommodate the science requirements of Flight Definition Principle Investigators studying cellular/dendritic growth in aluminum and lead alloys at processing temperatures up to 1200 C. The furnace implements a number of innovative features to achieve high thermal gradients and quench rates in a low-power, light-weight design. These include a pyrolytic boron nitride/graphite composite heating element surrounded by layers of self-supporting refractory metal shielding, and a graphite fiber enhanced cold zone allowing high levels of heat extraction from the sample crucible. Novel to the BUNDLE design is an in-situ helium gas quench capability that ensures rapid freezing of the solidifying region (mushy zone) of the metal sample within the furnace without sample disturbance prior to quenching; this is a stringent requirement for subsequent analysis and understanding of microstructural development. The experiment hardware concept features multiple furnaces that may be "bundled" together so many samples, currently up to eight, can be processed at one time. The design of BUNDLE is flexible enough to be implemented on the Shuttle and Space Station in a number of locations (SpaceHab, Express Rack, MPESS, ISPR, etc). BUNDLE prototype furnaces have directionally solidified and quenched 1cm diameter lead - 5.8 weight percent antimony and aluminum - 4 weight percent copper alloys. Quenching of the mushy zone, as recorded by in-situ thermocouples, occurred on the order of 0.5 seconds or less, a rate within the PI's requirements. Subsequent metallographic examination revealed the solidified microstructure to be, as expected, unidirectional. Both the dendrite tips and the eutectic reaction were planar in nature indicating uniform axial heat flow. Delineation between the growing dendrites and eutectic structure with the "quenched-in" liquid was sharp, attesting to the efficacy of the helium quench. BUNDLE's conception, development, capability, and adaptability are presented (in view of Flight PI's needs and science requirements) through viewgraphs depicting actual hardware, generated thermal analysis, and micrographs prepared from BUNDLE processed, flight-like samples.

Feeding behavior improves prediction of dairy cow voluntary feed intake but cannot serve as the sole indicator.

PubMed

Halachmi, I; Ben Meir, Y; Miron, J; Maltz, E

2016-09-01

Low-cost feeding-behavior sensors will soon be available for commercial use in dairy farms. The aim of this study was to develop a feed intake model for the individual dairy cow that includes feeding behavior. In a research farm, the individual cows' voluntary feed intake and feeding behavior were monitored at every meal. A feed intake model was developed based on data that exist in commercial modern farms: 'BW,' 'milk yield' and 'days in milking' parameters were applied in this study. At the individual cow level, eating velocity seemed to be correlated with feed intake (R 2=0.93 to 0.94). The eating velocity coefficient varied among individuals, ranging from 150 to 230 g/min per cow. The contribution of feeding behavior (0.28) to the dry matter intake (DMI) model was higher than the contribution of BW (0.20), similar to the contribution of fat-corrected milk (FCM)/BW (0.29) and not as large as the contribution of FCM (0.49). Incorporating feeding behavior into the DMI model improved its accuracy by 1.3 (38%) kg/cow per day. The model is ready to be implemented in commercial farms as soon as companies introduce low-cost feeding-behavior sensors on commercial level.

Overexpression of ShCYP51B and ShatrD in Sclerotinia homoeocarpa Isolates Exhibiting Practical Field Resistance to a Demethylation Inhibitor Fungicide

PubMed Central

Hulvey, Jon; Popko, James T.; Sang, Hyunkyu; Berg, Andrew

2012-01-01

We investigated genetic factors that govern the reduced propiconazole sensitivity of Sclerotinia homoeocarpa field isolates collected during a 2-year field efficacy study on dollar spot disease of turf in five New England sites. These isolates displayed a >50-fold range of in vitro sensitivity to a sterol demethylation inhibitor (DMI) fungicide, propiconazole, making them ideal for investigations of genetic mechanisms of reduced DMI sensitivity. The CYP51 gene homolog in S. homoeocarpa (ShCYP51B), encoding the enzyme target of DMIs, is likely a minor genetic factor for reduced propiconazole sensitivity, since there were no differences in constitutive relative expression (RE) values and only 2-fold-higher induced RE values for insensitive than for sensitive isolate groups. Next, we mined RNA-Seq transcriptome data for additional genetic factors and found evidence for the overexpression of a homolog of Botrytis cinerea atrD (BcatrD), ShatrD, a known efflux transporter of DMI fungicides. The ShatrD gene showed much higher constitutive and induced RE values for insensitive isolates. Several polymorphisms were found upstream of ShatrD but were not definitively linked to overexpression. The screening of constitutive RE values of ShCYP51B and ShatrD in isolates from two golf courses that exhibited practical field resistance to propiconazole uncovered evidence for significant population-specific overexpression of both genes. However, linear regression demonstrated that the RE of ShatrD displays a more significant relationship with propiconazole sensitivity than that of ShCYP51B. In summary, our results suggest that efflux is a major determinant of the reduced DMI sensitivity of S. homoeocarpa genotypes in New England, which may have implications for the emergence of practical field resistance in this important turfgrass pathogen. PMID:22798361

Chemical and Physical Predictors of the Nutritive Value of Wheat in Broiler Diets

PubMed Central

Ball, M. E. E.; Owens, B.; McCracken, K. J.

2013-01-01

The aim of this study was to establish relationships between chemical and physical parameters of wheat with performance and digestibilities of feed components in broiler chickens fed on wheat-based diets. Ninety-four wheat samples were selected for inclusion in four bird trials. Birds were housed in individual wire metabolism cages from 7 to 28 d and offered water and feed ad libitum. Dry matter intake (DMI), liveweight gain (LWG) and gain:feed were measured weekly. A balance collection was carried out from 14 to 21 d for determination of apparent metabolizable energy (AME), ME:gain, dry matter retention, oil and neutral detergent fibre (NDF) digestibility. At 28 d the birds were humanely killed, the contents of the jejunum removed for determination of in vivo viscosity and the contents of the ileum removed for determination of ileal dry matter, starch and protein digestibility. When wheat parameters were correlated with bird performance data, it was found that specific weight was not significantly (p>0.05) related to bird performance. Bird DMI, LWG and gain:feed were best correlated (p<0.05) with the rate of starch digestion, although the coefficients of correlation (r) were still low (0.246 to 0.523). A negative relationship (p<0.01) between AME and total (r = −0.432) and soluble (r = −0.304) non starch polysaccharide (NSP) was observed in this study. Thousand grain weight (TG) was positively correlated with DMI (r = 0.299), LWG (r = 0.343) and gain:feed (r = 0.371). When establishing multiple regression relationships, correlation coefficients greater than 0.8 were achieved for DMI, LWG, gain:feed and ileal crude protein digestibility. However, the economics involved in determining the parameters involved in the regressions make the process impractical. PMID:25049711

Effects of dietary cation-anion difference on intake, milk yield, and blood components of the early lactation cow.

PubMed

Chan, P S; West, J W; Bernard, J K; Fernandez, J M

2005-12-01

Early lactation Holsteins cows (15 primiparous and 18 multiparous) were offered rations with dietary cation-anion difference, calculated as mEq (Na + K - Cl - S)/100 g of feed dry matter (DCAD:S), of 20, 35, or 50 mEq from d 0 (calving) to 42 d postpartum (August 20, 2000 to January 9, 2001) to determine the effects of increasing DCAD:S on dry matter intake (DMI), milk yield, and blood metabolites. For DCAD:S of 20, 35, and 50, DMI was 3.30, 3.38, 2.96 kg/100 kg of body weight (BW); milk yield was 25.5, 24.2, and 22.4 kg/d, respectively. No differences were observed for concentration or yield of milk fat or milk protein. Serum Ca, P, Mg, Na, K, Cl, cation-anion difference, insulin, and glucose did not differ with DCAD. Serum HCO3- was 26.07, 25.88, and 27.64 mEq/L for 20, 35, and 50 DCAD:S. Serum Ca, Mg, Na, and K concentrations were greater for primiparous cows (9.52 mg/dL, 2.35 mg/dL, 140.03 mEq/L, 4.66 mEq/L, respectively) than for multiparous cows (9.27 mg/dL, 2.12 mg/dL, 137.63 mEq/L, 4.46 mEq/ L, respectively). A DCAD:S between 23 and 33 mEq/100 g of dry matter (DM) appears to be adequate during cool weather for the milk yield that occurred in the present study based on DMI (kg/100 kg of BW), whereas DCAD:S of 50 mEq/100 g of DM may be excessive and could be too alkaline or unpalatable, resulting in decreased DMI (kg/100 kg of BW).

Decision-Making Involvement and Prediction of Adherence in Youth With Type 1 Diabetes: A Cohort Sequential Study.

PubMed

Miller, Victoria A; Jawad, Abbas F

2018-05-17

To assess developmental trajectories of decision-making involvement (DMI), defined as the ways in which parents and children engage each other in decision-making about illness management, in youth with type 1 diabetes (T1D) and examine the effects of DMI on levels of and changes in adherence with age. Participants included 117 youth with T1D, enrolled at ages 8-16 years and assessed five times over 2 years. The cohort sequential design allowed for the approximation of the longitudinal curve from age 8 to 19 from overlapping cohort segments. Children and parents completed the Decision-Making Involvement Scale, which yields subscales for different aspects of DMI, and a self-report adherence questionnaire. Mixed-effects growth curve modeling was used for analysis, with longitudinal measures nested within participant and participants nested within cohort. Most aspects of DMI (Parent Express, Parent Seek, Child Express, and Joint) increased with child age; scores on some child report subscales (Parent Express, Child Seek, and Joint) decreased after age 12-14 years. After accounting for age, Child Seek, Child Express, and Joint were associated with overall higher levels of adherence in both child (estimates = 0.08-0.13, p < .001) and parent (estimates = 0.07- 0.13, p < .01) report models, but they did not predict changes in adherence with age. These data suggest that helping children to be more proactive in T1D discussions, by encouraging them to express their opinions, share information, and solicit guidance from parents, is a potential target for interventions to enhance effective self-management.

Estimation of endogenous protein and amino acid ileal losses in weaned piglets by regression analysis using diets with graded levels of casein

PubMed Central

2013-01-01

Background Many studies have investigated endogenous loss of proteins and amino acids (AAs) at the ileal level in growing pigs. However, only a few studies have researched this subject in piglets. Knowledge regarding AA ileal digestibility in piglets would be helpful during the formulation of diets for weaning piglets, rather than just using coefficients obtained in growing pigs. Therefore, in this study, we sought to estimate endogenous protein and AA ileal losses in piglets. Furthermore, apparent and true ileal digestibility (AID and TID) of protein and AAs from casein were measured. Results The average flow of protein was 20.8 g/kg of dry matter intake (DMI). Basal protein loss, as estimated by regression, was 16.9 g/kg DMI. Glutamic acid, arginine, and aspartic acid (2.2, 1.4, and 1.2 g/kg DMI, respectively) were the AAs for which greater losses were seen. The AID of protein and AAs increased as the protein level in the diet increased. A higher increment in AID was observed between diets with 80 and160 g CP/kg of feed; this finding was mainly attributable to increases in glycine and arginine (46.1% and 18%, respectively). The TID of protein was 97.8, and the TID of AAs varied from 93.9 for histidine to 100.2 for phenylalanine. Conclusions The basal endogenous protein loss in piglets was 16.9 g/kg DMI. Endogenous protein was rich in glutamic acid, aspartic acid, and arginine, which represented 32.7% of endogenous protein loss in weaning piglets. The TID of casein was high and varied from 93.0 for histidine to 100.2 for phenylalanine. PMID:24053636

Modelling and control of a diffusion/LPCVD furnace

NASA Astrophysics Data System (ADS)

Dewaard, H.; Dekoning, W. L.

1988-12-01

Heat transfer inside a cylindrical resistance diffusion/Low Pressure Chemical Vapor Deposition (LPCVD) furnace is studied with the aim of developing an improved temperature controller. A model of the thermal behavior is derived, which covers the important class of furnaces equipped with semitransparent quartz process tubes. The model takes into account the thermal behavior of the thermocouples. Currently used temperature controllers are shown to be highly inefficient for very large scale integration applications. Based on the model an alternative temperature controller of the LQG (linear quadratic Gaussian) type is proposed which features direct wafer temperature control. Some simulation results are given.

Active Control of Interface Shape During the Crystal Growth of Lead Bromide

NASA Technical Reports Server (NTRS)

Duval, W. M. B.; Batur, C.; Singh, N. B.

2003-01-01

A thermal model for predicting and designing the furnace temperature profile was developed and used for the crystal growth of lead bromide. The model gives the ampoule temperature as a function of the furnace temperature, thermal conductivity, heat transfer coefficients, and ampoule dimensions as variable parameters. Crystal interface curvature was derived from the model and it was compared with the predicted curvature for a particular furnace temperature and growth parameters. Large crystals of lead bromide were grown and it was observed that interface shape was in agreement with the shape predicted by this model.

Optical emission from a small scale model electric arc furnace in 250-600 nm region.

PubMed

Mäkinen, A; Niskanen, J; Tikkala, H; Aksela, H

2013-04-01

Optical emission spectroscopy has been for long proposed for monitoring and studying industrial steel making processes. Whereas the radiative decay of thermal excitations is always taking place in high temperatures needed in steel production, one of the most promising environment for such studies are electric arc furnaces, creating plasma in excited electronic states that relax with intense characteristic emission in the optical regime. Unfortunately, large industrial scale electric arc furnaces also present a challenging environment for optical emission studies and application of the method is not straightforward. To study the usability of optical emission spectroscopy in real electric arc furnaces, we have developed a laboratory scale DC electric arc furnace presented in this paper. With the setup, optical emission spectra of Fe, Cr, Cr2O3, Ni, SiO2, Al2O3, CaO, and MgO were recorded in the wavelength range 250-600 nm and the results were analyzed with the help of reference data. The work demonstrates that using characteristic optical emission, obtaining in situ chemical information from oscillating plasma of electric arc furnaces is indeed possible. In spite of complications, the method could possibly be applied to industrial scale steel making process in order to improve its efficiency.

CFD Modelling Applied to the Co-Combustion of Paper Sludge and Coal in a 130 t/h CFB Boiler

NASA Astrophysics Data System (ADS)

Yu, Z. S.; Ma, X. Q.; Lai, Z. Y.; Xiao, H. M.

Three-dimensional mathematical model has been developed as a tool for co-combustion of paper sludge and coal in a 130 tJh Circulating Fluidized Bed (CFB) boiler. Mathematical methods had been used based on a commercial software FLUENT for combustion. The predicted results of CFB furnace show that the co-combustion of paper sludge/coal is initially intensively at the bottom of bed; the temperature reaches its maximum in the dense-phase zone, around l400K. It indicates that paper sludge spout into furnace from the recycle inlet can increase the furnace maximum temperature (l396.3K), area-weighted average temperature (l109.6K) and the furnace gas outlet area-weighted average temperature(996.8K).The mathematical modeling also predicts that 15 mass% paper sludge co-combustion is the highest temperature at the flue gas outlet, it is 1000.8K. Moreover, it is proved that mathematical models can serve as a tool for detailed analysis of co-combustion of paper sludge and coal processes in a circulating fluidized bed furnace when in view of its convenience. The results gained from numerical simulation show that paper sludge enter into furnace from the recycle inlet excelled than mixing with coal and at the underside of phase interface.

Experimenting with concentrated sunlight using the DLR solar furnace

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neumann, A.; Groer, U.

1996-10-01

The high flux solar furnace that is operated by the Deutsche Forschungsanstalt fuer Luft- und Raumfahrt (DLR) at Cologne was inaugurated in June 1994 and we are now able to look back onto one year of successful operation. The solar furnace project was founded by the government of the State Northrhine Westfalia within the Study Group AG Solar. The optical design is a two-stage off-axis configuration which uses a flat 52 m{sup 2} heliostat and a concentrator composed of 147 spherical mirror facets. The heliostat redirects the solar light onto the concentrator which focuses the beam out of the opticalmore » axis of the system into the laboratory building. At high insolation levels (>800W/m{sup 2}) it is possible to collect a total power of 20 kW with peak flux densities of 4 MW/m{sup 2}. Sixteen different experiment campaigns were carried out during this first year of operation. The main research fields for these experiments were material science, component development and solar chemistry. The furnace also has its own research program leading to develop sophisticated measurement techniques like remote infrared temperature sensing and flux mapping. Another future goal to be realized within the next five years is the improvement of the performance of the furnace itself. 6 refs., 9 figs., 1 tab.« less

Robust emergence of a topological Hall effect in MnGa/heavy metal bilayers

NASA Astrophysics Data System (ADS)

Meng, K. K.; Zhao, X. P.; Liu, P. F.; Liu, Q.; Wu, Y.; Li, Z. P.; Chen, J. K.; Miao, J.; Xu, X. G.; Zhao, J. H.; Jiang, Y.

2018-02-01

We have investigated the topological Hall effect (THE) in MnGa/Pt and MnGa/Ta bilayers induced by the inter- facial Dzyaloshinskii-Moriya interaction (DMI). By varying the growth parameters, we can modulate the domain wall energy, and the largest THE signals are found when the domain wall energy is the smallest. The large topological portion of the Hall signal from the total Hall signal has been extracted in the whole temperature range from 5 to 300 K. These results open up the exploration of the DMI induced magnetic behavior based on the bulk perpendicular magnetic anisotropy materials for fundamental physics and magnetic storage technologies.

One-Pot Preparation of Dimethyl Isosorbide from d-Sorbitol via Dimethyl Carbonate Chemistry.

PubMed

Aricò, F; Aldoshin, A S; Tundo, P

2017-01-10

Direct synthesis of dimethyl isosorbide (DMI) from d-sorbitol via dimethyl carbonate (DMC) chemistry is herein first reported. High yield of DMI was achieved using the nitrogen superbase 1,5,7-triazabicyclo[4.4.0]dec-5-ene (TBD) as catalyst and performing the reaction in a stainless steel autoclave by increasing the temperature from 90 to 200 °C. In this procedure, DMC features its full capacity acting in the different steps of the process as carboxymethylating, leaving-group (cyclization), and methylating agent; DMC is also employed as the reaction media. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Composition-dependent magnetic response properties of Mn1 -xFexGe alloys

NASA Astrophysics Data System (ADS)

Mankovsky, S.; Wimmer, S.; Polesya, S.; Ebert, H.

2018-01-01

The composition-dependent behavior of the Dzyaloshinskii-Moriya interaction (DMI), the spin-orbit torque (SOT), as well as anomalous and spin Hall conductivities of Mn1 -xFexGe alloys have been investigated by first-principles calculations using the relativistic multiple scattering Korringa-Kohn-Rostoker (KKR) formalism. The Dxx component of the DMI exhibits a strong dependence on the Fe concentration, changing sign at x ≈0.85 in line with previous theoretical calculations as well as with experimental results demonstrating the change of spin helicity at x ≈0.8 . A corresponding behavior with a sign change at x ≈0.5 is predicted also for the Fermi-sea contribution to the SOT, because this is closely related to the DMI. In the case of anomalous and spin Hall effects it is shown that the calculated Fermi-sea contributions are rather small and the composition-dependent behavior of these effects are determined mainly by the electronic states at the Fermi level. The spin-orbit-induced scattering mechanisms responsible for both these effects suggest a common origin of the minimum of the anomalous Hall effect and the sign change of the spin Hall effect conductivities.

Speeding up nanomagnetic logic by DMI enhanced Pt/Co/Ir films

NASA Astrophysics Data System (ADS)

Ziemys, Grazvydas; Ahrens, Valentin; Mendisch, Simon; Csaba, Gyorgy; Becherer, Markus

2018-05-01

We investigated a new type of multilayer film for Nanomagnetic Logic with perpendicular anisotropy (pNML) enhanced by the Dzyaloshinskii-Moriya interaction (DMI). The DMI effect provides an additional energy term and widens the design space for pNML film optimization. In this work we added an Ir layer between Co and Pt to our standard pNML multilayer (ML) film stack - [Co/Pt]x4. Multilayer stacks of films with and w/o Ir were sputtered and patterned to nanowires of 400 nm width by means of focused ion beam lithography (FIB). For comparability of the films they were tuned to show identical anisotropy for multilayer stacks with and w/o Ir. The field-driven domain wall (DW) velocity in the nanowires was measured by using wide-field MOKE microscopy. We found a strong impact of Ir on the DW velocity being up to 2 times higher compared to the standard [Co/Pt]x4 ML films. Moreover, the maximum velocity is reached at much lower magnetic field, which is beneficial for pNML operation. These results pave the way for pNML with higher clocking rates and at the same time allow a further reduce power consumption.

RBANS memory percentage retention: No evidence of incremental validity beyond RBANS scores for diagnostic classification of mild cognitive impairment and dementia and for prediction of daily function.

PubMed

Jodouin, Kara A; O'Connell, Megan E; Morgan, Debra G

2017-01-01

RBANS percentage retention scores may be useful for diagnosis, but their incremental validity is unclear. Percentage retention versus RBANS immediate and delayed memory subtests and delayed index scores were compared for diagnostic classification and for prediction of function. Data from 173 memory clinic patients with an interdisciplinary diagnosis (no cognitive impairment, amnestic mild cognitive impairment [aMCI], and dementia due to Alzheimer's disease [AD]) and complete RBANS data were analyzed. Across diagnostic contrasts, list percentage retention classification accuracy was similar to List Learning delayed recall, but below the Delayed Memory Index (DMI). Similarly, for classifying no cognitive impairment versus aMCI or dementia due to AD, story percentage retention was similar to Story Memory subtests and below the DMI. For classifying aMCI versus AD; however, Story Memory exceeded the DMI, but was similar to Story Memory subtest scores. Similarly, for prediction of function percentage retention measures did not predict variance beyond that predicted by the RBANS subtest or index scores. In sum, there is no evidence that calculation of percentage retention for RBANS adds clinical utility beyond those provided by the standard RBANS scores.

Sensitivity of Podosphaera aphanis isolates to DMI fungicides: distribution and reduced cross-sensitivity.

PubMed

Sombardier, Audrey; Dufour, Marie-Cécile; Blancard, Dominique; Corio-Costet, Marie-France

2010-01-01

Management of strawberry powdery mildew, Podopshaera aphanis (Wallr.), requires numerous fungicide treatments. Limiting epidemics is heavily dependent on sterol demethylation inhibitors (DMIs) such as myclobutanil or penconazole. Recently, a noticeable reduction in the efficacy of these triazole fungicides was reported by strawberry growers in France. The goal of this study was to investigate the state of DMI sensitivity of French P. aphanis and provide tools for improved pest management. Using leaf disc sporulation assays, sensitivity to myclobutanil and penconazole of 23 isolates of P. aphanis was monitored. Myclobutanil EC(50) ranged from less than 0.1 to 14.67 mg L(-1) and for penconazole from 0.04 to 4.2 mg L(-1). A cross-analysis and a Venn diagram showed that there was reduced sensitivity and a positive correlation between the less sensitive myclobutanil and penconazole isolates; 73.9% of isolates were less sensitive to a DMI and 47.8% exhibited less sensitivity to both fungicides. The results show that sensitivity to myclobutanil and, to a lesser extent, penconazole has become less efficient in strawberry powdery mildew in France. Therefore, urgent action is required in order to document its appearance and optimise methods of control.

The Limits to Parapatric Speciation: Dobzhansky–Muller Incompatibilities in a Continent–Island Model

PubMed Central

Bank, Claudia; Bürger, Reinhard; Hermisson, Joachim

2012-01-01

How much gene flow is needed to inhibit speciation by the accumulation of Dobzhansky–Muller incompatibilities (DMIs) in a structured population? Here, we derive these limits in a classical migration–selection model with two haploid or diploid loci and unidirectional gene flow from a continent to an island. We discuss the dependence of the maximum gene-flow rate on ecological factors (exogeneous selection), genetic factors (epistasis, recombination), and the evolutionary history. Extensive analytical and numerical results show the following: (1) The maximum rate of gene flow is limited by exogeneous selection. In particular, maintenance of neutral DMIs is impossible with gene flow. (2) There are two distinct mechanisms that drive DMI evolution in parapatry, selection against immigrants in a heterogeneous environment and selection against hybrids due to the incompatibility. (3) Depending on the mechanism, opposite predictions result concerning the genetic architecture that maximizes the rate of gene flow a DMI can sustain. Selection against immigrants favors evolution of tightly linked DMIs of arbitrary strength, whereas selection against hybrids promotes the evolution of strong unlinked DMIs. In diploids, the fitness of the double heterozygotes is the decisive factor to predict the pattern of DMI stability. PMID:22542972

Effect of biotin on milk performance of dairy cattle: a meta-analysis.

PubMed

Chen, B; Wang, C; Wang, Y M; Liu, J X

2011-07-01

A meta-analysis of the effect of biotin on production outcomes of dairy cattle was conducted following a literature review. A total of 11 studies from 9 papers, with information on the milk production and composition data from a total number of 238 cows were extracted and analyzed using meta-analysis software in Stata. Estimated size of effect of biotin was calculated for dry matter intake (DMI), milk production, and composition. Heterogeneity was not significant for all of the parameters (the highest I(2)=12%). Therefore, fixed effects models were used for analysis. With the addition of biotin to lactating dairy cattle, DMI and milk production increased by 0.87 and 1.66 kg/d. No significant effect on percentage of milk fat and milk protein was observed. Additionally, Begg's test indicated no evidence of substantial publication bias for all variables. The influence analysis shows that the removal of any study did not change the direction or significance of the point estimates. It can be concluded that the use of biotin supplements increases DMI and milk yield in lactating dairy cows. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Meta-analysis of the influence of Saccharomyces cerevisiae supplementation on ruminal parameters and milk production of ruminants.

PubMed

Desnoyers, M; Giger-Reverdin, S; Bertin, G; Duvaux-Ponter, C; Sauvant, D

2009-04-01

The effects of yeast supplementation on intake, production, and rumen fermentation characteristics have been widely studied, but results are inconsistent between different studies. A quantitative meta-analysis was applied to 110 papers, 157 experiments, and 376 treatments dealing with yeast supplementation in ruminants. The objective was first to highlight the major quantitative effects of live yeast supplementation on intake, rumen fermentation, and milk production, and second, to identify major differences in experimental conditions between studies that can affect the response to treatment. Some of these experimental conditions are referred to as interfering factors. Yeast supplementation increased rumen pH (+0.03 on average) and rumen volatile fatty acid concentration (+2.17 mM on average), tended to decrease rumen lactic acid concentration (-0.9 mM on average), and had no influence on acetate-to-propionate ratio. Total-tract organic matter digestibility was also increased by yeast supplementation (+0.8% on average). Yeast supplementation increased dry matter intake (DMI; +0.44 g/kg of body weight; BW), milk yield (+1.2 g/kg of BW), and tended to increase milk fat content (+0.05%), but had no influence on milk protein content. Dose effects of yeast supplementation, expressed as log(10) [1+(cfu per 100 kg of BW)], globally confirmed the qualitative effects observed in the first analysis. The positive effect of yeast supplementation on rumen pH increased with the percentage of concentrate in the diet and with the DMI level. It was negatively correlated with the level of dietary neutral detergent fiber (NDF). The positive effect of yeast supplementation on rumen volatile fatty acid concentration increased with DMI and crude protein levels. The positive effect of yeast supplementation on organic matter digestibility increased with the percentage of concentrate and NDF in the diet. The negative effect of yeast supplementation on lactic acid concentration tended to decrease when the DMI level and the percentage of concentrate in the diet increased. The effects of interfering factors were globally similar when either dose effect or qualitative effect of yeast was taken into account. Although rumen fermentation efficiency per se was not measured, these results suggest an improvement in rumen fermentation by yeast supplementation. This effect could, however, be modulated by several different factors such as DMI, percentage of concentrate or NDF in the diet, or species.

Bacterial subclinical mastitis and its effect on milk yield in low-input dairy goat herds.

PubMed

Gelasakis, A I; Angelidis, A S; Giannakou, R; Filioussis, G; Kalamaki, M S; Arsenos, G

2016-05-01

The objectives of this study were (1) to record the major pathogens associated with subclinical mastitis (SCM), (2) to calculate their incidence during the milking period, and (3) to estimate the effect of SCM on daily milk yield (DMY) for goats reared under low-input management schemes. Dairy goats (n=590) of Skopelos and indigenous Greek breeds from 4 herds were randomly selected for the study. The study included monthly monitoring, milk yield recording, and bacteriological analyses of milk of individual goats during the course of 2 successive milking periods. Incidence and cumulative incidence were calculated for SCM cases. Moreover, 2 mixed linear regression models were built to assess the effects of (1) SCM and (2) different pathogens isolated from SCM cases, on DMY. The estimated incidence and cumulative incidence of SCM for the first and the second year of the study were 69.5 and 96.4 new cases of SCM/1,000 goat-months, and 24.1 and 31.7%, respectively. A total of 755 milk samples were subjected to microbiological examination, resulting in 661 positive cultures. Coagulase-negative and coagulase-positive staphylococci were isolated from 50.2 and 34.5% of the positive cultures, respectively. The incidence of infections (new infections per 1,000 goat-months) for the first and the second year of the study were 34 and 53 for coagulase-negative staphylococci, 23 and 28 for coagulase-positive staphylococci, 3 and 5 for Streptococcus/Enterococcus spp., and 5.5 and 9.1 for gram-negative bacteria. Goats with SCM had lower DMY when compared with goats without SCM (ca. 47g/d, corresponding to a 5.7% decrease in DMY). In particular, goats with SCM due to coagulase-positive staphylococci infection produced approximately 80g/d less milk (a reduction of ca. 9.7%) compared with uninfected ones, whereas SCM due to gram-negative bacteria resulted in approximately 15% reduction in DMY. Investigating the epidemiology of SCM and its effects on production traits is critical for the establishment of effective preventive measures against SCM and for the assessment of the sustainability of production in low-input dairy goat herds. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Comparison of three techniques for estimating the forage intake of lactating dairy cows on pasture.

PubMed

Macoon, B; Sollenberger, L E; Moore, J E; Staples, C R; Fike, J H; Portier, K M

2003-09-01

Quantifying DMI is necessary for estimation of nutrient consumption by ruminants, but it is inherently difficult on grazed pastures and even more so when supplements are fed. Our objectives were to compare three methods of estimating forage DMI (inference from animal performance, evaluation from fecal output using a pulse-dose marker, and estimation from herbage disappearance methods) and to identify the most useful approach or combination of approaches for estimating pasture intake by lactating dairy cows. During three continuous 28-d periods in the winter season, Holstein cows (Bos taurus; n = 32) grazed a cool-season grass or a cool-season grass-clover mixture at two stocking rates (SR; 5 vs. 2.5 cows/ha) and were fed two rates of concentrate supplementation (CS; 1 kg of concentrate [as-fed] per 2.5 or 3.5 kg of milk produced). Animal response data used in computations for the animal performance method were obtained from the latter 14 d of each period. For the pulse-dose marker method, chromium-mordanted fiber was used. Pasture sampling to determine herbage disappearance was done weekly throughout the study. Forage DMI estimated by the animal performance method was different among periods (P < 0.001; 6.5, 6.4, and 9.6 kg/d for Periods 1, 2, and 3, respectively), between SR (P < 0.001; 8.7 [low SR] vs. 6.3 kg/d [high SR]) and between CS (P < 0.01; 8.4 [low CS] vs. 6.6 kg/d [high CS]). The period and SR effect seemed to be related to forage mass. The pulse-dose marker method generally provided greater estimates of forage DMI (as much as 11.0 kg/d more than the animal performance method) and was not correlated with the other methods. Estimates of forage DMI by the herbage disappearance method were correlated with the animal performance method. The difference between estimates from these two methods, ranging from -4.7 to 5.4 kg/d, were much lower than their difference from pulse-dose marker estimates. The results of this study suggest that, when appropriate for the research objectives, the animal performance or herbage disappearance methods may be useful and less costly alternatives to using the pulse-dose method.

Nutrient intake, digestibility and performance of Gaddi kids supplemented with tea seed or tea seed saponin extract

PubMed Central

Kumar, M.; Kannan, A.; Bhar, R.; Gulati, A.; Gaurav, A.; Sharma, V. K.

2017-01-01

Objective An experiment was conducted to determine the nutrient intake, digestibility, microbial protein synthesis, haemato-biochemical attributes, immune response and growth performance of Gaddi kids fed with oat fodder based basal diet supplemented with either tea seed or tea seed saponin (TSS) extract. Methods Eighteen male kids, 7.03±0.16 months of age and 19.72±0.64 kg body weight, were distributed into three groups, T0 (control), T1, and T2, consisting of 6 animals each in a completely randomized design. The kids were fed a basal diet consisting of concentrate mixture and oat fodder (50:50). Animals in group III (T2) were supplemented with TSS at 0.4% of dry matter intake (DMI), and group II (T1) were supplemented with tea seed at 2.6% of DMI to provide equivalent dose of TSS as in T2. Two metabolism trials were conducted, 1st after 21 days and 2nd after 90 days of feeding to evaluate the short term and long term effects of supplementation. Results The tea seed (T1) or TSS (T2) supplementation did not affect DMI as well as the digestibility of dry matter, organic matter, crude protein, neutral detergent fibre, and acid detergent fibre. Nutritive value of diet and plane of nutrition were also comparable for both the periods. However, the average daily gain and feed conversion ratio (FCR) were improved (p<0.05) for T1 and T2 as compared to T0. The microbial protein supply was also higher (p<0.05) for T1 and T2 for both the periods. There was no effect of supplementation on most blood parameters. However, the triglyceride and low density lipoprotein cholesterol levels decreased (p<0.05) and high density lipoprotein-cholesterol level increased (p<0.05) in T2 as compared with T0 and T1. Supplementation also did not affect the cell mediated and humoral immune response in goats. Conclusion Tea seed at 2.6% of DMI and TSS at 0.4% DMI can be fed to Gaddi goats to improve growth rate, FCR and microbial protein synthesis. PMID:27608635

Methane emissions from two breeds of beef cows offered diets containing barley straw with either grass silage or brewers' grains.

PubMed

Duthie, C-A; Rooke, J A; Hyslop, J J; Waterhouse, A

2015-10-01

Increasing the concentration of dietary lipid is a promising strategy for reducing methane (CH4) emissions from ruminants. This study investigated the effect of replacing grass silage with brewers' grains on CH4 emissions of pregnant, non-lactating beef cows of two breeds. The experiment was a two×two factorial design comprising two breeds (LIMx, crossbred Limousin; and LUI, purebred Luing) and two diets consisting of (g/kg diet dry matter (DM)) barley straw (687) and grass silage (301, GS), or barley straw (763) and brewers' grains (226, BG), which were offered ad libitum. Replacing GS with BG increased the acid-hydrolysed ether extract concentration from 21 to 37 g/kg diet DM. Cows (n=48) were group-housed in equal numbers of each breed across two pens and each diet was allocated to one pen. Before measurements of CH4, individual dry matter intake (DMI), weekly BW and weekly body condition score were measured for a minimum of 3 weeks, following a 4-week period to acclimatise to the diets. CH4 emissions were subsequently measured on one occasion from each cow using individual respiration chambers. Due to occasional equipment failures, CH4 measurements were run over 9 weeks giving 10 observations for each breed×treatment combination (total n=40). There were no differences between diets for daily DMI measured in the chambers (9.92 v. 9.86 kg/day for BG and GS, respectively; P>0.05). Cows offered the BG diet produced less daily CH4 than GS-fed cows (131 v. 156 g/day: P0.05). However, when expressed as a proportion of metabolic BW (BW0.75), LUI cows had greater DMI than LIMx cows (84.5 v. 75.7 g DMI/kg BW0.75, P<0.05) and produced more CH4 per kg BW0.75 than LIMx cows (1.30 v. 1.05 g CH4/kg BW0.75; P<0.01). Molar proportions of acetate were higher (P<0.001) and propionate and butyrate lower (P<0.01) in rumen fluid samples from BG-fed compared with GS-fed cows. This study demonstrated that replacing GS with BG in barley straw-based diets can effectively reduce CH4 emissions from beef cows, with no suppression of DMI.

Methane emissions, body composition, and rumen fermentation traits of beef heifers differing in residual feed intake.

PubMed

Fitzsimons, C; Kenny, D A; Deighton, M H; Fahey, A G; McGee, M

2013-12-01

This study examined the relationship of residual feed intake (RFI) and performance with methane emissions, rumen fermentation, and digestion in beef heifers. Individual DMI and growth performance were measured for 22 Simmental heifers (mean initial BW 449 kg, SD = 46.2 kg) offered grass silage ad libitum for 120 d. Ultrasonically scanned muscle and fat depth, BCS, muscularity score, skeletal measurements, blood variables, rumen fermentation (via stomach tube), and total tract digestibility (indigestible marker) were measured. Methane production was estimated using the sulfur hexafluoride tracer gas technique over two 5-d periods beginning on d 20 and 75 of the RFI measurement period. Phenotypic RFI was calculated as actual DMI minus expected DMI. The residuals of the regression of DMI on ADG and midtest metabolic body weight, using all heifers, were used to compute individual RFI coefficients. Heifers were ranked by RFI and assigned to low (efficient), medium, or high (inefficient) groupings. Overall ADG and DMI were 0.58 kg (SD = 0.18) and 7.40 kg (SD = 0.72), respectively. High-RFI heifers consumed 9 and 15% more (P < 0.05) than medium- and low-RFI groups, respectively. Body weight, growth, skeletal, and composition traits did not differ (P > 0.05) between low- and high-RFI groups. High-RFI heifers had higher concentrations of plasma glucose (6%) and urea (13%) and lower concentrations of plasma creatinine (9%) than low-RFI heifers (P < 0.05). Rumen pH and apparent in vivo digestibility did not differ (P > 0.05) between RFI groups, although acetate:propionate ratio was lowest (P = 0.07) for low-RFI (3.5) and highest for high-RFI (4.6) heifers. Methane production expressed as grams per day or grams per kilogram metabolic body weight was greater (P < 0.05) for high (297 g/d and 2.9 g/kg BW0.75) compared with low (260 g/d and 2.5 g/kg BW0.75) RFI heifers, with medium (275 g/d and 2.7 g/kg BW0.75) RFI heifers being intermediate. Regression analysis indicated that a 1 kg DM/d increase in RFI was associated with a 23 g/d increase (P = 0.09) in methane emissions. Results suggest that improved RFI will reduce methane emissions without affecting productivity of growing beef cattle.

High Level Information Fusion (HLIF) with nested fusion loops

NASA Astrophysics Data System (ADS)

Woodley, Robert; Gosnell, Michael; Fischer, Amber

2013-05-01

Situation modeling and threat prediction require higher levels of data fusion in order to provide actionable information. Beyond the sensor data and sources the analyst has access to, the use of out-sourced and re-sourced data is becoming common. Through the years, some common frameworks have emerged for dealing with information fusion—perhaps the most ubiquitous being the JDL Data Fusion Group and their initial 4-level data fusion model. Since these initial developments, numerous models of information fusion have emerged, hoping to better capture the human-centric process of data analyses within a machine-centric framework. 21st Century Systems, Inc. has developed Fusion with Uncertainty Reasoning using Nested Assessment Characterizer Elements (FURNACE) to address challenges of high level information fusion and handle bias, ambiguity, and uncertainty (BAU) for Situation Modeling, Threat Modeling, and Threat Prediction. It combines JDL fusion levels with nested fusion loops and state-of-the-art data reasoning. Initial research has shown that FURNACE is able to reduce BAU and improve the fusion process by allowing high level information fusion (HLIF) to affect lower levels without the double counting of information or other biasing issues. The initial FURNACE project was focused on the underlying algorithms to produce a fusion system able to handle BAU and repurposed data in a cohesive manner. FURNACE supports analyst's efforts to develop situation models, threat models, and threat predictions to increase situational awareness of the battlespace. FURNACE will not only revolutionize the military intelligence realm, but also benefit the larger homeland defense, law enforcement, and business intelligence markets.

3-D Transient Heat Transfer Analysis of Slab Heating Characteristics in a Reheating Furnace in Hot Strip Mills

NASA Astrophysics Data System (ADS)

Jang, J. Y.; Lee, Y. W.; Lin, C. N.; Wang, C. H.

2016-05-01

A three-dimensional mathematical transient heat transfer model for the prediction of temperature distribution within the slab has been developed by considering the thermal radiation in the walking-beam-type reheating furnace chamber. The steel slabs are heated up through the non-firing, preheating, 1st-heating, 2nd-heating, and soaking zones in the furnace, respectively, where the furnace wall temperature is function of time. Comparison with the in-situ experimental data from Steel Company in Taiwan shows that the present heat transfer model works well for the prediction of thermal behavior of the slab in the reheating furnace. The effects of different skid button height (H=60mm, 90mm, and 120mm) and different gap distance between two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark formation and temperature profiles are investigated. It is found that the skid mark severity decreases with an increase in the skid button height. The effect of gap distance is important only for the slab edge planes, while it is insignificant for the slab central planes.

A 3D mathematical model for the horizontal anode baking furnace

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kocaefe, Y.S.; Dernedde, E.; Kocaefe, D.

In the aluminum industry, carbon anodes are baked in large horizontal or vertical ring-type furnaces. The anode quality depends strongly on the baking conditions (heating rate, soaking time and final anode temperature). A three-dimensional mathematical model has been developed for a horizontal anode baking furnace to assess the effects of different parameters on the baking process and to improve the furnace operation and design at Noranda Aluminum Smelter in New Madrid, Missouri. The commercial CFD code CFDS-FLOW3D is used to solve the governing differential equations. The model gives the temperature, velocity and concentration distributions in the flue, and the variationmore » of the temperature distribution with time in the pit. In this paper, a description of the 3D model for the horizontal anode baking furnace will be given. Some of the results from a case study will also be presented. The results show clearly the importance of flue geometry on the gas flow distribution in the flue and the heat transfer to the anodes.« less

An experimental investigation of concentrated slop combustion characteristics in cyclone furnace

NASA Astrophysics Data System (ADS)

Panpokha, Suphaopich; Wongwuttanasatian, Tanakorn; Tangchaichit, Kiatfa

2018-02-01

Slop is a by-product in alcoholic industries requiring costly waste management. An idea of using slop as a fuel in a boiler for the industries was proposed. Due to high content of ash, a cyclone furnace was designed to combust the slop. This study aims to examine the concentrated slop combustion in a designed cyclone furnace, consisting of combustion temperature and exhaust gases. The tests were carried out under 4 different air-fuel ratios. Fuels injected into the furnace were 3 g/s of concentrated slop and 1 g/s of diesel. The air-fuel ratios were corresponding to 100, 120, 140 and 160 percent theoretical air. The results demonstrated that combustion of concentrated slop can gave temperature of 800-1000°C and a suitable theoretical air was 100%-120%, because the combustion temperature was higher than that of other cases. In cyclone combustion, excess air is not recommended because it affects a reduction in overall temperature inside the cyclone furnace. It is expected that utilization of the concentrated slop (by-product) will be beneficial in the development of green and zero waste factory.

Reducing treatment of coppersmelting slag: Thermodynamic analysis of impurities behavior

NASA Astrophysics Data System (ADS)

Komkov, Alexey; Kamkin, Rostislav

2011-01-01

A thermodynamic mathematical model, describing behavior of Pb, Zn, and As during reducing slag cleaning in the Vanyukov furnace has been developed. Using a developed model, the influence of different factors, such as temperature, oxygen partial pressure, the ratio of the formed phases on the behavior of impurities, was analyzed. It was found that arsenic can significantly move to the bottom phase, and zinc can be significantly vaporized under conditions in the Vanyukov furnace.

Measures of methane production and their phenotypic relationships with dry matter intake, growth, and body composition traits in beef cattle.

PubMed

Herd, R M; Arthur, P F; Donoghue, K A; Bird, S H; Bird-Gardiner, T; Hegarty, R S

2014-11-01

Ruminants contribute up to 80% of greenhouse gas (GHG) emissions from livestock, and enteric methane production by ruminants is the main source of these GHG emissions. Hence, reducing enteric methane production is essential in any GHG emissions reduction strategy in livestock. Data from 2 performance-recording research herds of Angus cattle were used to evaluate a number of methane measures that target methane production (MPR) independent of feed intake and to examine their phenotypic relationships with growth and body composition. The data comprised 777 young bulls and heifers that were fed a roughage diet (ME of 9 MJ/kg DM) at 1.2 times their maintenance energy requirements and measured for MP in open circuit respiration chambers for 48 h. Methane traits evaluated included DMI during the methane measurement period, MPR, and methane yield (MY; MPR/DMI), with means (± SD) of 6.2 ± 1.4 kg/d, 187 ± 38 L/d, and 30.4 ± 3.5 L/kg, respectively. Four forms of residual MPR (RMP), which is a measure of actual minus predicted MPR, were evaluated. For the first 3 forms, predicted MPR was calculated using published equations. For the fourth (RMPR), predicted MPR was obtained by regression of MPR on DMI. Growth traits evaluated were BW at birth, weaning (200 d of age), yearling age (400 d of age), and 600 d of age, with means (± SD) of 34 ± 4.6, 238 ± 37, 357 ± 45, and 471 ± 53 kg, respectively. Body composition traits included ultrasound measures (600 d of age) of rib fat, rump fat, and eye muscle area, with means (± SD) of 3.8 ± 2.6 mm, 5.4 ± 3.8 mm, and 61 ± 7.7 cm(2), respectively. Methane production was positively correlated (r ± SE) with DMI (0.65 ± 0.02), MY (0.72 ± 0.02), the RMP traits (r from 0.65 to 0.79), the growth traits (r from 0.19 to 0.57), and the body composition traits (r from 0.13 to 0.29). Methane yield was, however, not correlated (r ± SE) with DMI (-0.02 ± 0.04) as well as the growth (r from -0.03 to 0.11) and body composition (r from 0.01 to 0.06) traits. All the RMP traits were strongly correlated to MY (r from 0.82 to 0.95). These results indicate that reducing MPR per se can have a negative impact on growth and body composition of cattle. Reducing MY, however, will likely have the effect of reducing MPR without impacting productivity. Where a ratio trait is undesirable, as in animal breeding, any of the RMP traits can be used instead of MY. However, where independence from DMI is desired, RMPR should be a trait worth considering.

Effects of replacement of late-harvested grass silage and barley with early-harvested silage on milk production and methane emissions.

PubMed

Cabezas-Garcia, E H; Krizsan, S J; Shingfield, K J; Huhtanen, P

2017-07-01

This study evaluated the effects of gradual replacement of a mixture of late-cut grass silage (LS) and barley with early-cut grass silage (ES) on milk production, CH 4 emissions, and N utilization in Swedish Red cows. Two grass silages were prepared from the same primary growth of timothy grass sward but harvested 2 wk apart [11.0 and 9.7 MJ of metabolizable energy/kg of dry matter (DM)]. Four diets, fed as a total mixed ration, were formulated to meet the metabolizable energy and protein requirements of 35 kg of energy-corrected milk (ECM) by gradually replacing a mixture of LS and barley with ES (0, 33, 67, and 100% of the forage component of the diet), whereas the proportion of barley decreased from 47.2 to 26.6% of diet DM. Expeller canola meal was used as a protein supplement. Sixteen Swedish Red cows were used in 4 replicated 4 × 4 Latin squares. Cows were offered diets ad libitum and milked twice daily. Each period of 28 d comprised 14 d of diet adaptation followed by 14 d of data collection. Intake and milk yield were recorded daily, and milk samples were collected on d 19 to 21 and d 26 to 28 of each period. Diet digestibility was determined by grab sampling using indigestible neutral detergent fiber as an internal marker. Gas emissions were measured using the GreenFeed system (C-Lock Inc., Rapid City, SD). Dry matter intake (DMI) linearly decreased from 22.6 to 19.3 kg/d as the proportion of ES increased in the diet. The ECM yield did not differ among treatments, but milk protein yield decreased with increasing proportion of ES in the diet. Because of reduced DMI with increasing ES, feed efficiency (ECM/DMI) improved with an increased proportion of ES in the diet. Nitrogen efficiency (milk N/N intake) did not change despite a linear increase in milk urea N concentration from 9.7 (LS alone) to 11.9 mg/dL (ES alone) with graded replacement of LS and barley by ES in the diet. Lower DMI responses in ES diets were partly compensated for by increased organic matter digestibility (656 g/kg of DM for LS alone; 715 g/kg of DM for ES alone) related to improved forage digestibility at early harvesting. Total CH 4 emissions and CH 4 intensity (CH 4 /ECM) were not influenced by diet, but CH 4 yield (CH 4 /DMI) increased linearly from 19.5 to 23.0 g/kg of DMI with greater inclusion of ES in the diet. In conclusion, replacing LS and barley with ES improved the conversion of feed to milk without increasing CH 4 emissions or compromising N efficiency. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Rumen-protected lysine, methionine, and histidine increase milk protein yield in dairy cows fed a metabolizable protein-deficient diet.

PubMed

Lee, C; Hristov, A N; Cassidy, T W; Heyler, K S; Lapierre, H; Varga, G A; de Veth, M J; Patton, R A; Parys, C

2012-10-01

The objective of this experiment was to evaluate the effect of supplementing a metabolizable protein (MP)-deficient diet with rumen-protected (RP) Lys, Met, and specifically His on dairy cow performance. The experiment was conducted for 12 wk with 48 Holstein cows. Following a 2-wk covariate period, cows were blocked by DIM and milk yield and randomly assigned to 1 of 4 diets, based on corn silage and alfalfa haylage: control, MP-adequate diet (ADMP; MP balance: +9 g/d); MP-deficient diet (DMP; MP balance: -317 g/d); DMP supplemented with RPLys (AminoShure-L, Balchem Corp., New Hampton, NY) and RPMet (Mepron; Evonik Industries AG, Hanau, Germany; DMPLM); and DMPLM supplemented with an experimental RPHis preparation (DMPLMH). The analyzed crude protein content of the ADMP and DMP diets was 15.7 and 13.5 to 13.6%, respectively. The apparent total-tract digestibility of all measured nutrients, plasma urea-N, and urinary N excretion were decreased by the DMP diets compared with ADMP. Milk N secretion as a proportion of N intake was greater for the DMP diets compared with ADMP. Compared with ADMP, dry matter intake (DMI) tended to be lower for DMP, but was similar for DMPLM and DMPLMH (24.5, 23.0, 23.7, and 24.3 kg/d, respectively). Milk yield was decreased by DMP (35.2 kg/d), but was similar to ADMP (38.8 kg/d) for DMPLM and DMPLMH (36.9 and 38.5kg/d, respectively), paralleling the trend in DMI. The National Research Council 2001model underpredicted milk yield of the DMP cows by an average (±SE) of 10.3 ± 0.75 kg/d. Milk fat and true protein content did not differ among treatments, but milk protein yield was increased by DMPLM and DMPLMH compared with DMP and was not different from ADMP. Plasma essential amino acids (AA), Lys, and His were lower for DMP compared with ADMP. Supplementation of the DMP diets with RP AA increased plasma Lys, Met, and His. In conclusion, MP deficiency, approximately 15% below the National Research Council requirements from 2001, decreased DMI and milk yield in dairy cows. Supplementation of the MP-deficient diet with RPLys and RPMet diminished the difference in DMI and milk yield compared with ADMP and additional supplementation with RPHis eliminated it. As total-tract fiber digestibility was decreased with the DMP diets, but DMI tended to increase with RP AA supplementation, we propose that, similar to monogastric species, AA play a role in DMI regulation in dairy cows. Our data implicate His as a limiting AA in high-producing dairy cows fed corn silage- and alfalfa haylage-based diets, deficient in MP. The MP-deficient diets clearly increased milk N efficiency and decreased dramatically urinary N losses. Copyright © 2012 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Acoustical Measurement Of Furnace Temperatures

NASA Technical Reports Server (NTRS)

Parthasarathy, Shakkottai; Venkateshan, Shakkottai P.

1989-01-01

Simple probes withstand severe conditions, yet give spatially-resolved temperature readings. Prototype acoustical system developed to measure temperatures from ambient to 1,800 degree F in such structures as large industrial lime kilns and recovery-boiler furnaces. Pulses of sound reflected from obstructions in sensing tube. Speed of sound and temperature in each segment deduced from travel times of pulses.

Space Station Furnace Facility. Volume 2: Appendix 1: Contract End Item specification (CEI), part 1

NASA Technical Reports Server (NTRS)

Seabrook, Craig

1992-01-01

This specification establishes the performance, design, development, and verification requirements for the Space Station Furnace Facility (SSFF) Core. The definition of the SSFF Core and its interfaces, specifies requirements for the SSFF Core performance, specifies requirements for the SSFF Core design, and construction are presented, and the verification requirements are established.

40 CFR 52.1173 - Control strategy: Particulates.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Electric Arc Furnaces, Sintering Plants, Blast Furnaces, Heating and Reheating Furnaces. (2) Rules 336.1371... Basic Oxygen Furnaces, Electric Arc Furnaces, Sintering Plants, Blast Furnaces and Heating and Reheating... the receiving car itself during the pushing operation; (b) in the phrase “eight consecutive trips...

40 CFR 52.1173 - Control strategy: Particulates.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., Electric Arc Furnaces, Sintering Plants, Blast Furnaces, Heating and Reheating Furnaces. (2) Rules 336.1371... Basic Oxygen Furnaces, Electric Arc Furnaces, Sintering Plants, Blast Furnaces and Heating and Reheating... the receiving car itself during the pushing operation; (b) in the phrase “eight consecutive trips...

40 CFR 52.1173 - Control strategy: Particulates.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Electric Arc Furnaces, Sintering Plants, Blast Furnaces, Heating and Reheating Furnaces. (2) Rules 336.1371... Basic Oxygen Furnaces, Electric Arc Furnaces, Sintering Plants, Blast Furnaces and Heating and Reheating... the receiving car itself during the pushing operation; (b) in the phrase “eight consecutive trips...

40 CFR 52.1173 - Control strategy: Particulates.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Electric Arc Furnaces, Sintering Plants, Blast Furnaces, Heating and Reheating Furnaces. (2) Rules 336.1371... Basic Oxygen Furnaces, Electric Arc Furnaces, Sintering Plants, Blast Furnaces and Heating and Reheating... the receiving car itself during the pushing operation; (b) in the phrase “eight consecutive trips...

Computational Modeling of Arc-Slag Interaction in DC Furnaces

NASA Astrophysics Data System (ADS)

Reynolds, Quinn G.

2017-02-01

The plasma arc is central to the operation of the direct-current arc furnace, a unit operation commonly used in high-temperature processing of both primary ores and recycled metals. The arc is a high-velocity, high-temperature jet of ionized gas created and sustained by interactions among the thermal, momentum, and electromagnetic fields resulting from the passage of electric current. In addition to being the primary source of thermal energy, the arc jet also couples mechanically with the bath of molten process material within the furnace, causing substantial splashing and stirring in the region in which it impinges. The arc's interaction with the molten bath inside the furnace is studied through use of a multiphase, multiphysics computational magnetohydrodynamic model developed in the OpenFOAM® framework. Results from the computational solver are compared with empirical correlations that account for arc-slag interaction effects.

LSSA large area silicon sheet task continuous Czochralski process development

NASA Technical Reports Server (NTRS)

Rea, S. N.

1978-01-01

A Czochralski crystal growing furnace was converted to a continuous growth facility by installation of a premelter to provide molten silicon flow into the primary crucible. The basic furnace is operational and several trial crystals were grown in the batch mode. Numerous premelter configurations were tested both in laboratory-scale equipment as well as in the actual furnace. The best arrangement tested to date is a vertical, cylindrical graphite heater containing small fused silicon test tube liner in which the incoming silicon is melted and flows into the primary crucible. Economic modeling of the continuous Czochralski process indicates that for 10 cm diameter crystal, 100 kg furnace runs of four or five crystals each are near-optimal. Costs tend to asymptote at the 100 kg level so little additional cost improvement occurs at larger runs. For these conditions, crystal cost in equivalent wafer area of around $20/sq m exclusive of polysilicon and slicing was obtained.

Application of Waste Heat Recovery Energy Saving Technology in Reform of UHP-EAF

NASA Astrophysics Data System (ADS)

Zhao, J. H.; Zhang, S. X.; Yang, W.; Yu, T.

2017-08-01

The furnace waste heat of a company’s existing 4 × 100t ultra-high-power electric arc furnaces is not used and discharged directly of the situation has been unable to meet the national energy-saving emission reduction requirements, and also affected their own competitiveness and sustainable development. In order to make full use of the waste heat of the electric arc furnace, this paper presents an the energy-saving transformation program of using the new heat pipe boiler on the existing ultra-high-power electric arc furnaces for recovering the waste heat of flue gas. The results show that after the implementation of the project can save energy equivalent to 42,349 tons of standard coal. The flue gas waste heat is fully utilized and dust emission concentration is accorded with the standard of Chinese invironmental protection, which have achieved good results.

The adaption of coal quality to furnace structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Z.; Shun, X.

1996-12-31

This paper gives the research result of coal quality adaption to furnace structure. The designing of a furnace is based on the coal quality that the furnace would fire. If the coal fired in the furnace differs from the design coal, there would be a lot of problems such as flame stability, coal burn-out rate and slagging problem for the furnace during its operation. In order to know the adaptional range of coal quality for an existing furnace the authors had chosen three different furnaces and 18 kinds of coals in their research work. To understand the coal combustion characteristicsmore » they introduce different indexes to show different processes of coal combustion. These indexes include Fz index which demonstrates the coal combustion based on its utility analyzed result, flame stability index, combustion characteristic index and char burn-out index which are based on the analyzed result of thermogravimetric characteristic. As a furnace is built up and set into operation its flame stability, burn-out rate and ash deposition are definite. If a furnace`s fuel changes its structure characteristics and operation condition will change. A relation between coal quality to furnace structure is based on a lot of regressional analysis results of existing furnaces and their fuels. Based on this relation the adaption of coal quality for a furnace are defined and the kinds of coal furnace fired are optimized to its design fuel.« less

Geological Sequestration of CO2 by Hydrous Carbonate Formation with Reclaimed Slag

DOE Office of Scientific and Technical Information (OSTI.GOV)

Von L. Richards; Kent Peaslee; Jeffrey Smith

The concept of this project is to develop a process that improves the kinetics of the hydrous carbonate formation reaction enabling steelmakers to directly remove CO2 from their furnace exhaust gas. It is proposed to bring the furnace exhaust stream containing CO2 in contact with reclaimed steelmaking slag in a reactor that has an environment near the unit activity of water resulting in the production of carbonates. The CO2 emissions from the plant would be reduced by the amount sequestered in the formation of carbonates. The main raw materials for the process are furnace exhaust gases and specially prepared slag.

Modeling and control of diffusion and low-pressure chemical vapor deposition furnaces

NASA Astrophysics Data System (ADS)

De Waard, H.; De Koning, W. L.

1990-03-01

In this paper a study is made of the heat transfer inside cylindrical resistance diffusion and low-pressure chemical vapor deposition furnaces, aimed at developing an improved temperature controller. A model of the thermal behavior is derived which also covers the important class of furnaces equipped with semitransparent quartz process tubes. The model takes into account the thermal behavior of the thermocouples. It is shown that currently used temperature controllers are highly inefficient for very large scale integration applications. Based on the model an alternative temperature controller of the linear-quadratic-Gaussian type is proposed which features direct wafer temperature control. Some simulation results are given.

Dross treatment in a rotary arc furnace with graphite electrodes

NASA Astrophysics Data System (ADS)

Drouet, Michel G.; Handfield, My; Meunier, Jean; Laflamme, Claude B.

1994-05-01

Aluminum baths are always covered with a layer of dross resulting from the aluminum surface oxidation. This dross represents 1-10% of the melt and may contain up to 75wt.% aluminum. Since aluminum production is highly energy intensive, dross recycling is very attractive from both energy and economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally unacceptable because of the production of salt slags. Hydro-Quebec has developed a new technology using a rotary arc furnace with graphite electrodes. This process provides aluminum recovery rates of 80-90%, using a highly energy efficient, environmentally sound production method.

Advanced dendritic web growth development and development of single-crystal silicon dendritic ribbon and high-efficiency solar cell program

NASA Technical Reports Server (NTRS)

Duncan, C. S.; Seidensticker, R. G.; Mchugh, J. P.; Hopkins, R. H.

1986-01-01

Efforts to demonstrate that the dendritic web technology is ready for commercial use by the end of 1986 continues. A commercial readiness goal involves improvements to crystal growth furnace throughput to demonstrate an area growth rate of greater than 15 sq cm/min while simultaneously growing 10 meters or more of ribbon under conditions of continuous melt replenishment. Continuous means that the silicon melt is being replenished at the same rate that it is being consumed by ribbon growth so that the melt level remains constant. Efforts continue on computer thermal modeling required to define high speed, low stress, continuous growth configurations; the study of convective effects in the molten silicon and growth furnace cover gas; on furnace component modifications; on web quality assessments; and on experimental growth activities.

Numerical Study of the Reduction Process in an Oxygen Blast Furnace

NASA Astrophysics Data System (ADS)

Zhang, Zongliang; Meng, Jiale; Guo, Lei; Guo, Zhancheng

2016-02-01

Based on computational fluid dynamics, chemical reaction kinetics, principles of transfer in metallurgy, and other principles, a multi-fluid model for a traditional blast furnace was established. The furnace conditions were simulated with this multi-fluid mathematical model, and the model was verified with the comparison of calculation and measurement. Then a multi-fluid model for an oxygen blast furnace in the gasifier-full oxygen blast furnace process was established based on this traditional blast furnace model. With the established multi-fluid model for an oxygen blast furnace, the basic characteristics of iron ore reduction process in the oxygen blast furnace were summarized, including the changing process of the iron ore reduction degree and the compositions of the burden, etc. The study found that compared to the traditional blast furnace, the magnetite reserve zone in the furnace shaft under oxygen blast furnace condition was significantly reduced, which is conducive to the efficient operation of blast furnace. In order to optimize the oxygen blast furnace design and operating parameters, the iron ore reduction process in the oxygen blast furnace was researched under different shaft tuyere positions, different recycling gas temperatures, and different allocation ratios of recycling gas between the hearth tuyere and the shaft tuyere. The results indicate that these three factors all have a substantial impact on the ore reduction process in the oxygen blast furnace. Moderate shaft tuyere position, high recycling gas temperature, and high recycling gas allocation ratio between hearth and shaft could significantly promote the reduction of iron ore, reduce the scope of the magnetite reserve zone, and improve the performance of oxygen blast furnace. Based on the above findings, the recommendations for improvement of the oxygen blast furnace design and operation were proposed.

Improving Gas Furnace Performance: A Field and Laboratory Study at End of Life

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brand, L.; Yee, S.; Baker, J.

2015-02-01

In 2010, natural gas provided 54% of total residential space heating energy the U.S. on a source basis, or 3.5 Quadrillion Btu. Natural gas burned in furnaces accounted for 92% of that total, and boilers and other equipment made up the remainder. A better understanding of installed furnace performance is a key to energy savings for this significant energy usage. Natural gas furnace performance can be measured in many ways. The annual fuel utilization efficiency (AFUE) rating provides a fixed value under specified conditions, akin to the EPA miles per gallon rating for new vehicles. The AFUE rating is providedmore » by the manufacturer to the consumer and is a way to choose between models tested on the same basis. This value is commonly used in energy modeling calculations. ASHRAE 103 is a consensus furnace testing standard developed by the engineering community. The procedure provided in the standard covers heat-up, cool down, condensate heat loss, and steady-state conditions and an imposed oversize factor. The procedure can be used to evaluate furnace performance with specified conditions or with some variation chosen by the tester. In this report the ASHRAE 103 test result will be referred to as Annualized Efficiency (AE) to avoid confusion, and any non-standard test conditions will be noted. Aside from these two laboratory tests, steady state or flue loss efficiency can be measured in the field under many conditions; typically as found or tuned to the manufacturers recommended settings. In this report, AE and steady-state efficiency will be used as measures of furnace performance.« less

Near-isothermal furnace for in situ and real time X-ray radiography solidification experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Becker, M., E-mail: maike.becker@dlr.de; Dreißigacker, C.; Klein, S.

2015-06-15

In this paper, we present a newly developed near-isothermal X-ray transparent furnace for in situ imaging of solidification processes in thin metallic samples. We show that the furnace is ideally suited to study equiaxed microstructure evolution and grain interaction. To observe the growth dynamics of equiaxed dendritic structures, a minimal temperature gradient across the sample is required. A uniform thermal profile inside a circular sample is achieved by positioning the sample in the center of a cylindrical furnace body surrounded by a circular heater arrangement. Performance tests with the hypo-eutectic Al-15wt.%Cu and the near-eutectic Al-33wt.%Cu alloys validate the near-isothermal charactermore » of the sample environment. Controlled cooling rates of less than 0.5 K min{sup −1} up to 10 K min{sup −1} can be achieved in a temperature range of 720 K–1220 K. Integrated in our rotatable laboratory X-ray facility, X-RISE, the furnace provides a large field of view of 10.5 mm in diameter and a high spatial resolution of ∼4 μm. With the here presented furnace, equiaxed dendrite growth models can be rigorously tested against experiments on metal alloys by, e.g., enabling dendrite growth velocities to be determined as a function of undercooling or solutal fields in front of the growing dendrite to be measured.« less

Spontaneous nucleation and topological stabilization of skyrmions in magnetic nanodisks with the interfacial Dzyaloshinskii-Moriya interaction

NASA Astrophysics Data System (ADS)

Kolesnikov, A. G.; Samardak, A. S.; Stebliy, M. E.; Ognev, A. V.; Chebotkevich, L. A.; Sadovnikov, A. V.; Nikitov, S. A.; Kim, Yong Jin; Cha, In Ho; Kim, Young Keun

2017-05-01

One of the major societal challenges is reducing the power consumption of information technology (IT) devices and numerous data centers. Distinct from the current approaches based on switching of magnetic single-domain nanostructures or on movement of domain walls under high currents, an original magnetic skyrmion technology offers ultra-low power, fast, high-density, and scalable spintronic devices, including non-volatile random access memory. Using data-driven micromagnetic simulations, we demonstrate the possibility of spontaneous nucleation and stabilization of different skyrmionic states, such as skyrmions, merons, and meron-like configurations, in heavy metal/ferromagnetic nanodisks with the interfacial Dzyaloshinskii-Moriya interaction (iDMI) as a result of quasi-static magnetization reversal only. Since iDMI is not easily modulated in real systems, we show that skyrmion stabilization is easily achievable by manipulating magnetic anisotropy, saturation magnetization, and the diameters of nanodisks. The state diagrams, presented in terms of the topological charge, allow to explicitly distinguish the intermediate states between skyrmions and merons and can be used for developing a skyrmionic medium, which has been recently proposed to be a building block for future spin-orbitronic devices.

A Robust Vehicle Localization Approach Based on GNSS/IMU/DMI/LiDAR Sensor Fusion for Autonomous Vehicles

PubMed Central

Meng, Xiaoli

2017-01-01

Precise and robust localization in a large-scale outdoor environment is essential for an autonomous vehicle. In order to improve the performance of the fusion of GNSS (Global Navigation Satellite System)/IMU (Inertial Measurement Unit)/DMI (Distance-Measuring Instruments), a multi-constraint fault detection approach is proposed to smooth the vehicle locations in spite of GNSS jumps. Furthermore, the lateral localization error is compensated by the point cloud-based lateral localization method proposed in this paper. Experiment results have verified the algorithms proposed in this paper, which shows that the algorithms proposed in this paper are capable of providing precise and robust vehicle localization. PMID:28926996

Driving chiral domain walls in antiferromagnets using rotating magnetic fields

NASA Astrophysics Data System (ADS)

Pan, Keming; Xing, Lingdi; Yuan, H. Y.; Wang, Weiwei

2018-05-01

We show theoretically and numerically that an antiferromagnetic domain wall can be moved by a rotating magnetic field in the presence of Dzyaloshinskii-Moriya interaction (DMI). Two motion modes are found: rigid domain wall motion at low frequency (corresponding to the perfect frequency synchronization) and the oscillating motion at high frequency. In the full synchronized region, the steady velocity of the domain wall is universal, in the sense that it depends only on the frequency of the rotating field and the ratio between DMI strength and exchange constant. The domain wall velocity is independent of the Gilbert damping and the rotating field strength. Moreover, a rotating field in megahertz is sufficient to move the antiferromagnetic domain wall.

A Robust Vehicle Localization Approach Based on GNSS/IMU/DMI/LiDAR Sensor Fusion for Autonomous Vehicles.

PubMed

Meng, Xiaoli; Wang, Heng; Liu, Bingbing

2017-09-18

Precise and robust localization in a large-scale outdoor environment is essential for an autonomous vehicle. In order to improve the performance of the fusion of GNSS (Global Navigation Satellite System)/IMU (Inertial Measurement Unit)/DMI (Distance-Measuring Instruments), a multi-constraint fault detection approach is proposed to smooth the vehicle locations in spite of GNSS jumps. Furthermore, the lateral localization error is compensated by the point cloud-based lateral localization method proposed in this paper. Experiment results have verified the algorithms proposed in this paper, which shows that the algorithms proposed in this paper are capable of providing precise and robust vehicle localization.

INTERIOR VIEW SHOWING FURNACE KEEPER OBSERVING FURNACE THROUGH BLUE GLASS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW SHOWING FURNACE KEEPER OBSERVING FURNACE THROUGH BLUE GLASS EVERY TWENTY MINUTES TO DETERMINE SIZE AND TEXTURE OF BATCH AND OTHER VARIABLES. FAN IN FRONT COOLS WORKERS AS THEY CONDUCT REPAIRS. FURNACE TEMPERATURE AT 1572 DEGREES FAHRENHEIT. - Chambers-McKee Window Glass Company, Furnace No. 2, Clay Avenue Extension, Jeannette, Westmoreland County, PA

Predictability of the Indian Ocean Dipole in the coupled models

NASA Astrophysics Data System (ADS)

Liu, Huafeng; Tang, Youmin; Chen, Dake; Lian, Tao

2017-03-01

In this study, the Indian Ocean Dipole (IOD) predictability, measured by the Indian Dipole Mode Index (DMI), is comprehensively examined at the seasonal time scale, including its actual prediction skill and potential predictability, using the ENSEMBLES multiple model ensembles and the recently developed information-based theoretical framework of predictability. It was found that all model predictions have useful skill, which is normally defined by the anomaly correlation coefficient larger than 0.5, only at around 2-3 month leads. This is mainly because there are more false alarms in predictions as leading time increases. The DMI predictability has significant seasonal variation, and the predictions whose target seasons are boreal summer (JJA) and autumn (SON) are more reliable than that for other seasons. All of models fail to predict the IOD onset before May and suffer from the winter (DJF) predictability barrier. The potential predictability study indicates that, with the model development and initialization improvement, the prediction of IOD onset is likely to be improved but the winter barrier cannot be overcome. The IOD predictability also has decadal variation, with a high skill during the 1960s and the early 1990s, and a low skill during the early 1970s and early 1980s, which is very consistent with the potential predictability. The main factors controlling the IOD predictability, including its seasonal and decadal variations, are also analyzed in this study.

Enviro-HIRLAM online integrated meteorology-chemistry modelling system: strategy, methodology, developments and applications (v7.2)

NASA Astrophysics Data System (ADS)

Baklanov, Alexander; Smith Korsholm, Ulrik; Nuterman, Roman; Mahura, Alexander; Pagh Nielsen, Kristian; Hansen Sass, Bent; Rasmussen, Alix; Zakey, Ashraf; Kaas, Eigil; Kurganskiy, Alexander; Sørensen, Brian; González-Aparicio, Iratxe

2017-08-01

The Environment - High Resolution Limited Area Model (Enviro-HIRLAM) is developed as a fully online integrated numerical weather prediction (NWP) and atmospheric chemical transport (ACT) model for research and forecasting of joint meteorological, chemical and biological weather. The integrated modelling system is developed by the Danish Meteorological Institute (DMI) in collaboration with several European universities. It is the baseline system in the HIRLAM Chemical Branch and used in several countries and different applications. The development was initiated at DMI more than 15 years ago. The model is based on the HIRLAM NWP model with online integrated pollutant transport and dispersion, chemistry, aerosol dynamics, deposition and atmospheric composition feedbacks. To make the model suitable for chemical weather forecasting in urban areas, the meteorological part was improved by implementation of urban parameterisations. The dynamical core was improved by implementing a locally mass-conserving semi-Lagrangian numerical advection scheme, which improves forecast accuracy and model performance. The current version (7.2), in comparison with previous versions, has a more advanced and cost-efficient chemistry, aerosol multi-compound approach, aerosol feedbacks (direct and semi-direct) on radiation and (first and second indirect effects) on cloud microphysics. Since 2004, the Enviro-HIRLAM has been used for different studies, including operational pollen forecasting for Denmark since 2009 and operational forecasting atmospheric composition with downscaling for China since 2017. Following the main research and development strategy, further model developments will be extended towards the new NWP platform - HARMONIE. Different aspects of online coupling methodology, research strategy and possible applications of the modelling system, and fit-for-purpose model configurations for the meteorological and air quality communities are discussed.

CHARGING SIDE OF #130 ELECTRIC FURNACE CO. REHEAT FURNACE IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CHARGING SIDE OF #130 ELECTRIC FURNACE CO. REHEAT FURNACE IN REROLL BAY. CAKES FROM THE CASTING SHOP ARE BROUGHT UP TO ROLLING TEMPERATURE IN ONE OF TWO (#130 AND 146) GAS-FIRED FURNACES. A RADIO-CONTROLLED OVERHEAD CRANE TRANSFERS CAKES FROM FLATCARS TO THE ROLLER LINE LEADING INTO THE FURNACE. CAKES ARE HEATED AT 900-1000 DEGREES FAHRENHEIT FOR THREE TO FOUR HOURS. RATED FURNACE CAPACITY IS 100,000 LBS.\\HOUR. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

Danish auroral science history

NASA Astrophysics Data System (ADS)

Stauning, P.

2011-01-01

Danish auroral science history begins with the early auroral observations made by the Danish astronomer Tycho Brahe during the years from 1582 to 1601 preceding the Maunder minimum in solar activity. Included are also the brilliant observations made by another astronomer, Ole Rømer, from Copenhagen in 1707, as well as the early auroral observations made from Greenland by missionaries during the 18th and 19th centuries. The relations between auroras and geomagnetic variations were analysed by H. C. Ørsted, who also played a vital role in the development of Danish meteorology that came to include comprehensive auroral observations from Denmark, Iceland and Greenland as well as auroral and geomagnetic research. The very important auroral investigations made by Sophus Tromholt are outlined. His analysis from 1880 of auroral observations from Greenland prepared for the significant contributions from the Danish Meteorological Institute, DMI, (founded in 1872) to the first International Polar Year 1882/83, where an expedition headed by Adam Paulsen was sent to Greenland to conduct auroral and geomagnetic observations. Paulsen's analyses of the collected data gave many important results but also raised many new questions that gave rise to auroral expeditions to Iceland in 1899 to 1900 and to Finland in 1900 to 1901. Among the results from these expeditions were 26 unique paintings of the auroras made by the artist painter, Harald Moltke. The expedition to Finland was headed by Dan la Cour, who later as director of the DMI came to be in charge of the comprehensive international geomagnetic and auroral observations made during the Second International Polar Year in 1932/33. Finally, the article describes the important investigations made by Knud Lassen during, among others, the International Geophysical Year 1957/58 and during the International Quiet Sun Year (IQSY) in 1964/65. With his leadership the auroral and geomagnetic research at DMI reached a high international level that came to be the background for the first Danish satellite, Ørsted, successfully launched in 1999 and still in operation.

Assessing environmental risks for high intensity agriculture using the material flow analysis method--a case study of the Dongting Lake basin in South Central China.

PubMed

Yin, Guanyi; Liu, Liming; Yuan, Chengcheng

2015-07-01

This study primarily examined the assessment of environmental risk in high intensity agricultural areas. Dongting Lake basin was taken as a case study, which is one of the major grain producing areas in China. Using data obtained from 1989 to 2012, we applied Material Flow Analysis (MFA) to show the material consumption, pollutant output and production storage in the agricultural-environmental system and assessed the environmental risk index on the basis of the MFA results. The results predicted that the status of the environmental quality of the Dongting Lake area is unsatisfactory for the foreseeable future. The direct material input (DMI) declined by 13.9%, the domestic processed output (DPO) increased by 28.21%, the intensity of material consumption (IMC) decreased by 36.7%, the intensity of material discharge (IMD) increased by 10%, the material productivity (MP) increased by 27 times, the environmental efficiency (EE) increased by 15.31 times, and the material storage (PAS) increased by 0.23%. The DMI and DPO was higher at rural places on the edge of cities, whereas the risk of urban agriculture has arisen due to the higher increasing rate of DMI and DPO in cities compared with the counties. The composite environmental risk index increased from 0.33 to 0.96, indicating that the total environmental risk changed gradually but seriously during the 24 years assessed. The driving factors that affect environmental risk in high intensity agriculture can be divided into five classes: social, economic, human, natural and disruptive incidents. This study discussed a number of effective measures for protecting the environment while ensuring food production yields. Additional research in other areas and certain improvements of this method in future studies may be necessary to develop a more effective method of managing and controlling agricultural-environmental interactions.

Effects of seasonal change and parity on raw milk composition and related indices in Chinese Holstein cows in northern China.

PubMed

Yang, L; Yang, Q; Yi, M; Pang, Z H; Xiong, B H

2013-01-01

This study was to investigate the effects of seasonal change and parity on milk composition and related indices, and to analyze the relationships among milk indices in Chinese Holstein cows from an intensive dairy farm in northern China. The 6,520 sets of complete Dairy Herd Improvement data were obtained and grouped by natural month and parity. The data included daily milk yield (DMY), milk solids percentage (MSP), milk fat percentage (MFP), milk protein percentage (MPP), milk lactose percentage (MLP), somatic cell count (SCC), somatic cell score (SCS), milk production loss (MPL), and fat-to-protein ratio (FPR). Data analysis showed that the above 9 indices were affected by both seasonal change and parity. However, the interaction between parity and seasonal change showed effects on MLP, SCS, MPL, and DMY, but no effects on MFP, MPP, MSP, and FPR. Duncan's multiple comparison on seasonal change showed that DMY (23.58 kg/d), MSP (12.35%), MPP (3.02%), and MFP (3.81%) were the lowest in June, but SCC (288.7 × 10(3)/mL) and MPL (0.69 kg/d) were the lowest in January; FPR (1.32) was the highest in February. Meanwhile, Duncan's multiple comparison on parities showed that MSP, MPP, and MLP were reduced rapidly in the fourth lactation, but SCC and MPL increased with increasing parities. The canonical correlation analysis for indices showed that SCS had high positive correlation with MPL (0.8360). Therefore, a few models were developed to quantify the effects of seasonal change and parity on raw milk composition using the Wood model. The changing patterns of milk composition and related indices in different months and parities could provide scientific evidence for improving feeding management and nutritional supplementation of Chinese Holstein cows. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

SU-G-BRA-06: Quantification of Tracking Performance of a Multi-Layer Electronic Portal Imaging Device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Y; Rottmann, J; Myronakis, M

2016-06-15

Purpose: The purpose of this study was to quantify the improvement in tumor tracking, with and without fiducial markers, afforded by employing a multi-layer (MLI) electronic portal imaging device (EPID) over the current state-of-the-art, single-layer, digital megavolt imager (DMI) architecture. Methods: An ideal observer signal-to-noise ratio (d’) approach was used to quantify the ability of an MLI EPID and a current, state-of-the-art DMI EPID to track lung tumors from the treatment beam’s-eye-view. Using each detector modulation transfer function (MTF) and noise power spectrum (NPS) as inputs, a detection task was employed with object functions describing simple three-dimensional Cartesian shapes (spheresmore » and cylinders). Marker-less tumor tracking algorithms often use texture discrimination to differentiate benign and malignant tissue. The performance of such algorithms is simulated by employing a discrimination task for the ideal observer, which measures the ability of a system to differentiate two image quantities. These were defined as the measured textures for benign and malignant lung tissue. Results: The NNPS of the MLI ∼25% of that of the DMI at the expense of decreased MTF at intermediate frequencies (0.25≤« less

pKI values of prazosin and idazoxan for receptors stimulated by neuronally released transmitter in the epididymal portion of rat isolated vas deferens.

PubMed

Mackay, D; Kengatharan, M

1994-01-01

1. A new method has been used to measure pKI values of prazosin and idazoxan against neuronally-released transmitter in the epididymal portion of the rat isolated vas deferens. The most reproducible results were obtained with a prolonged antagonist equilibration time (1 h). 2. Under these conditions the pKI of prazosin was practically unaffected by addition of alpha, beta-methylene-adenosine-5'-triphosphate (10 microM) to desensitize purinoceptors. Addition of desmethylimipramine (DMI) (0.3 microM) produced a small, but statistically non-significant, reduction. 3. The same method has been used to measure the pKI of prazosin against exogenous noradrenaline. In the latter case addition of DMI (0.3 microM) and corticosterone (30 microM) together produced a statistically significant reduction in the apparent pKI of prazosin. 4. The new method for estimating pKI values shows that DMI itself acts either pseudo-irreversibly or non-competitively and may be reducing the apparent pKI of prazosin. 5. The pKI values obtained for prazosin and idazoxan against neuronally-released transmitter are in good agreement with those obtained by other workers for the actions of these drugs on alpha-adrenoceptors.

EAF Management Optimization

NASA Astrophysics Data System (ADS)

Costoiu, M.; Ioana, A.; Semenescu, A.; Marcu, D.

2016-11-01

The article presents the main advantages of electric arc furnace (EAF): it has a great contribution to reintroduce significant quantities of reusable metallic materials in the economic circuit, it constitutes itself as an important part in the Primary Materials and Energy Recovery (PMER), good productivity, good quality / price ratio, the possibility of developing a wide variety of classes and types of steels, including special steels and high alloy. In this paper it is presented some important developments of electric arc furnace: vacuum electric arc furnace, artificial intelligence expert systems for pollution control Steelworks. Another important aspect presented in the article is an original block diagram for optimization the EAF management system. This scheme is based on the original objective function (criterion function) represented by the price / quality ratio. The article presents an original block diagram for optimization the control system of the EAF. For designing this concept of EAF management system, many principles were used.

Mathematical modeling of the burden distribution in the blast furnace shaft

NASA Astrophysics Data System (ADS)

Park, Jong-In; Jung, Hun-Je; Jo, Min-Kyu; Oh, Han-Sang; Han, Jeong-Whan

2011-06-01

Process efficiency in the blast furnace is influenced by the gas flow pattern, which is dictated by the burden profile. Therefore, it is important to control the burden distribution so as to achieve reasonable gas flow in the blast furnace operation. Additionally, the charging pattern selection is important as it affects the burden trajectory and stock profile. For analysis of the burden distribution, a new analysis model was developed by use of the spreadsheet program, Microsoft® Office Excel, based on visual basic. This model is composed of the falling burden trajectory and a stock model. The burden trajectory is determined by the burden type, batch weight, rotating velocity of the chute, tilting angle, and friction coefficient. After falling, stock lines are formed by the angle of repose, which is affected by the burden trajectory and the falling velocity. The mathematical formulas for developing this model were modified by a scaled model experiment and DEM simulation.

Ultra-High Efficiency and Low-Emissions Combustion Technology for Manufacturing Industries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Atreya, Arvind

2013-04-15

The purpose of this research was to develop and test a transformational combustion technology for high temperature furnaces to reduce the energy intensity and carbon footprint of U.S. manufacturing industries such as steel, aluminum, glass, metal casting, and petroleum refining. A new technology based on internal and/or external Flue Gas Recirculation (FGR) along with significant enhancement in flame radiation was developed. It produces "Radiative Flameless Combustion (RFC)" and offers tremendous energy efficiency and pollutant reduction benefits over and above the now popular "flameless combustion." It will reduce the energy intensity (or fuel consumption per unit system output) by more thanmore » 50% and double the furnace productivity while significantly reducing pollutants and greenhouse gas emissions (10^3 times reduction in NOx and 10 times reduction in CO & hydrocarbons and 3 times reduction in CO2). Product quality improvements are also expected due to uniform radiation, as well as, reduction in scale/dross formation is expected because of non-oxidative atmosphere. RFC is inexpensive, easy to implement, and it was successfully tested in a laboratory-scale furnace at the University of Michigan during the course of this work. A first-ever theory with gas and particulate radiation was also developed. Numerical programs were also written to design an industrial-scale furnace. Nine papers were published (or are in the process of publication). We believe that this early stage research adequately proves the concept through laboratory experiments, modeling and computational models. All this work is presented in the published papers. Important conclusions of this work are: (1) It was proved through experimental measurements that RFC is not only feasible but a very beneficial technology. (2) Theoretical analysis of RFC was done in (a) spatially uniform strain field and (b) a planar momentum jet where the strain rate is neither prescribed nor uniform. Four important non-dimensional parameters controlling RFC in furnaces were identified. These are: (i) The Boltzmann number; (ii) The Damkohler number, (iii) The dimensionless Arrhenius number, and (iv) The equivalence ratio. Together they define the parameter space where RFC is possible. It was also found that the Damkohler number must be small for RFC to exist and that the Boltzmann number expands the RFC domain. The experimental data obtained during the course of this work agrees well with the predictions made by the theoretical analysis. Interestingly, the equivalence ratio dependence shows that it is easier to establish RFC for rich mixtures than for lean mixtures. This was also experimentally observed. Identifying the parameter space for RFC is necessary for controlling the RFC furnace operation. It is hoped that future work will enable the methodology developed here to be applied to the operation of real furnaces, with consequent improvement in efficiency and pollutant reduction. To reiterate, the new furnace combustion technology developed enables intense radiation from combustion products and has many benefits: (i) Ultra-High Efficiency and Low-Emissions; (ii) Uniform and intense radiation to substantially increase productivity; (iii) Oxygen-free atmosphere to reduce dross/scale formation; (iv) Provides multi-fuel capability; and (v) Enables carbon sequestration if pure oxygen is used for combustion.« less

Scaleable Clean Aluminum Melting Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Han, Q.; Das, S.K.

2008-02-15

The project entitled 'Scaleable Clean Aluminum Melting Systems' was a Cooperative Research and Development Agreements (CRADAs) between Oak Ridge National Laboratory (ORNL) and Secat Inc. The three-year project was initially funded for the first year and was then canceled due to funding cuts at the DOE headquarters. The limited funds allowed the research team to visit industrial sites and investigate the status of using immersion heaters for aluminum melting applications. Primary concepts were proposed on the design of furnaces using immersion heaters for melting. The proposed project can continue if the funding agency resumes the funds to this research. Themore » objective of this project was to develop and demonstrate integrated, retrofitable technologies for clean melting systems for aluminum in both the Metal Casting and integrated aluminum processing industries. The scope focused on immersion heating coupled with metal circulation systems that provide significant opportunity for energy savings as well as reduction of melt loss in the form of dross. The project aimed at the development and integration of technologies that would enable significant reduction in the energy consumption and environmental impacts of melting aluminum through substitution of immersion heating for the conventional radiant burner methods used in reverberatory furnaces. Specifically, the program would couple heater improvements with furnace modeling that would enable cost-effective retrofits to a range of existing furnace sizes, reducing the economic barrier to application.« less

Dry matter intake, body condition score, and grazing behavior of nonlactating, pregnant dairy cows fed kale or grass once versus twice daily during winter.

PubMed

Rugoho, I; Edwards, G R

2018-01-01

The objective of this study was to examine the effect of wintering pregnant, nonlactating dairy cows outdoors on either kale or grass, fed in 1 [11 kg dry matter (DM) of kale or grass + 3 kg DM of baled barley straw offered in the morning] or 2 allocations (5.5 kg DM of kale or grass grazed + 1.5 kg DM of barley straw offered morning and afternoon) per day. The body condition score (BCS) gain over the 47-d winter feeding period was higher for grass-fed (0.5 BCS units) than kale-fed cows (0.3 BCS units), but was unaffected by feeding frequency. Forage DM utilization was higher for kale-fed (97%) than grass-fed cows (76%), leading to higher estimated dry matter intake (DMI) in kale-fed (10.7 kg of DM/cow per day) than grass-fed cows (7.7 kg of DM/cow per day). Forage DM utilization and estimated DMI were not affected by feeding frequency. Prehension bite rate was greater for grass-fed (37.3 bites/min) than kale-fed cows (7.6 bites/min), but more mastication bites were required for kale-fed cows. Cumulative DMI after 2, 3, and 6 h was greater in cows allocated forage once than twice a day and for kale than grass after 3 and 6 h. Mean eating time was greater for cows offered forage once (477 min) than twice (414 min) per day. In conclusion, increasing feeding frequency from once to twice per day decreased the intake rate within the first 6 h after allocation, but did not affect total daily DMI, DM utilization or BCS gain. Thus, moving cows more frequently would not have any significant advantage. It may increase labor requirements, thereby creating a more challenging wintering management than feeding once per day. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The effects of increasing garlic powder and monensin supplementation on feed intake, nutrient digestibility, growth performance and blood parameters of growing calves.

PubMed

Gholipour, A; Foroozandeh Shahraki, A D; Tabeidian, S A; Nasrollahi, S M; Yang, W Z

2016-08-01

The objective of this study was to evaluate the effects of increasing garlic powder and monensin supplementation on feed intake, nutrient digestibility, growth performance and blood metabolites of growing calves. Forty Holstein calves (BW = 100 ± 11 kg) were randomly assigned to four dietary treatments (n = 10) in a complete randomized design. Experimental treatments consisted of the following: (i) basal diet (control), (ii) basal diet supplemented with 0.0003% of dietary dry matter (DM) sodium monensin, (iii) low level of garlic powder (Low-GAR; 0.5% of dietary DM) and (iv) high level of garlic powder (High-GAR; 1% of dietary DM). DM intake (DMI) and DM digestibility were (p < 0.05) decreased by High-GAR. However, calves supplemented with Low-GAR had a similar DMI to the control calves and similar DM digestibility to the control and monensin groups. The digestibility of other nutrients were not affected by the treatments. Although supplementing monensin relative to Low-GAR increased the DMI (p < 0.05), average daily gain was similar between Low-GAR and monensin supplemented calves, which were higher than the control and High-GAR groups (p < 0.05). As a result, feed conversion ratio was improved in the Low-GAR group versus other treatment groups (p < 0.05). Administrating garlic powder decreased the blood low-density lipoprotein (LDL) and non-esterified fatty acids (p < 0.05) without affecting the blood triglyceride, high-density lipoprotein and beta-hydroxybutyric acid concentrations. In conclusion, the calves fed the Low-GAR showed an improved FCR and blood metabolites without changing the DMI and nutrient digestibility. It suggests that garlic powder could be used as an alternative to monensin for growing calves under the current feeding conditions. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.

Strategic grazing management towards sustainable intensification at tropical pasture-based dairy systems.

PubMed

Congio, Guilhermo F S; Batalha, Camila D A; Chiavegato, Marília B; Berndt, Alexandre; Oliveira, Patrícia P A; Frighetto, Rosa T S; Maxwell, Thomas M R; Gregorini, Pablo; Da Silva, Sila C

2018-05-01

Agricultural systems are responsible for environmental impacts that can be mitigated through the adoption of more sustainable principles. Our objective was to investigate the influence of two pre-grazing targets (95% and maximum canopy light interception during pasture regrowth; LI 95% and LI Max , respectively) on sward structure and herbage nutritive value of elephant grass cv. Cameroon, and dry matter intake (DMI), milk yield, stocking rate, enteric methane (CH 4 ) emissions by Holstein × Jersey dairy cows. We hypothesized that grazing strategies modifying the sward structure of elephant grass (Pennisetum purpureum Schum.) improves nutritive value of herbage, increasing DMI and reducing intensity of enteric CH 4 emissions, providing environmental and productivity benefits to tropical pasture-based dairy systems. Results indicated that pre-sward surface height was greater for LI Max (≈135 cm) than LI 95% (≈100 cm) and can be used as a reliable field guide for monitoring sward structure. Grazing management based on LI 95% criteria improved herbage nutritive value and grazing efficiency, allowing greater DMI, milk yield and stocking rate by dairy cows. Daily enteric CH 4 emission was not affected; however, cows grazing elephant grass at LI 95% were more efficient and emitted 21% less CH 4 /kg of milk yield and 18% less CH 4 /kg of DMI. The 51% increase in milk yield per hectare overcame the 29% increase in enteric CH 4 emissions per hectare in LI 95% grazing management. Thereby the same resource allocation resulted in a 16% mitigation of the main greenhouse gas from pasture-based dairy systems. Overall, strategic grazing management is an environmental friendly practice that improves use efficiency of allocated resources through optimization of processes evolving plant, ruminant and their interface, and enhances milk production efficiency of tropical pasture-based systems. Copyright © 2018 Elsevier B.V. All rights reserved.

Distributions of Sensitivities to Three Sterol Demethylation Inhibitor Fungicides Among Populations of Uncinula necator Sensitive and Resistant to Triadimefon.

PubMed

Erickson, E O; Wilcox, W F

1997-08-01

ABSTRACT Single-conidial isolates of Uncinula necator from (i) a population representing two vineyards with no previous exposure to sterol demethylation inhibitor (DMI) fungicides ("unexposed," n = 77) and (ii) a population representing two vineyards in which powdery mildew was poorly controlled by triadimefon after prolonged DMI use ("selected," n = 82) were assayed to determine distributions of sensitivities to the DMI fungicides triadimenol (the active form of triadimefon), myclobutanil, and fenarimol. Median 50% effective dose (ED(50)) values (micrograms per milliliter) in the selected versus unexposed populations were 0.06 versus 1.9 for triadimenol, 0.03 versus 0.23 for myclobutanil, and 0.03 versus 0.07 for fenarimol, respectively. Isolates were grouped into sensitivity classes according to their ED(50) values, and those from the selected population were categorized as resistant if the frequency of their sensitivity class had increased significantly relative to levels found in the unexposed population (ED(50) values exceeding 0.56, 0.18, and 0.18 mug/ml for triadimenol, myclobutanil, and fenarimol, respectively). Of the 76 isolates defined as resistant to triadimenol, 64% were classified as cross-resistant to myclobutanil, 18% were classified as cross-resistant to fenarimol, and 17% were classified as resistant to all three fungicides; 25% of the isolates classified as resistant to myclobutanil also were classified as resistant to fenarimol. Similar cross-resistance relationships were revealed when all isolates were examined by regressing log ED(50) values for each fungicide against those for the remaining two fungicides to determine the correlation coefficients (e.g., r = 0.85 for triadimenol versus myclobutanil and 0.56 for triadimenol versus fenarimol). The restricted levels of cross-resistance indicated by these data, particularly between fenarimol and the other two fungicides, is in sharp contrast to the high levels of cross-resistance among DMIs reported for some other pathogens and has significant implications with respect to programs for managing grapevine powdery mildew and DMI resistance.

SU-E-T-624: Portal Dosimetry Commissioning of Multiple (6) Varian TrueBeam Linacs Equipped with PortalVision DMI MV Imager

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weldon, M; DiCostanzo, D; Grzetic, S

2015-06-15

Purpose: To show that a single model for Portal Domisetry (PD) can be established for beam-matched TrueBeam™ linacs that are equipped with the DMI imager (43×43cm effective area). Methods: Our department acquired 6 new TrueBeam™s, 4 “Slim” and 2 “Edge” models. The Slims were equipped with 6 and 10MV photons, and the Edges with 6MV. MLCs differed between the Slims and Edges (Millennium 120 vs HD-MLC respectively). PD model was created from data acquired using a single linac (Slim). This includes maximum field size profile, as well as output factors and acquired measured fluence using the DMI imager. All identicalmore » linacs were beam-matched, profiles were within 1% at maximum field size at a variety of depths. The profile correction file was generated from 40×40 profile acquired at 5cm depth, 95cm SSD, and was adjusted for deviation at the field edges and corners. The PD model and profile correction was applied to all six TrueBeam™s and imagers. A variety of jaw only and sliding window (SW) MLC test fields, as well as TG-119 and clinical SW and VMAT plans were run on each linac to validate the model. Results: For 6X and 10X, field by field comparison using 3mm/3% absolute gamma criteria passed 90% or better for all cases. This was also true for composite comparisons of TG-199 and clinical plans, matching our current department criteria. Conclusion: Using a single model per photon energy for PD for the TrueBeam™ equipped with a DMI imager can produce clinically acceptable results across multiple identical and matched linacs. It is also possible to use the same PD model despite different MLCs. This can save time during commissioning and software updates.« less

Intravenous lipid infusion affects dry matter intake, methane yield, and rumen bacteria structure in late-lactating Holstein cows.

PubMed

Lamp, Ole; Reyer, Henry; Otten, Winfried; Nürnberg, Gerd; Derno, Michael; Wimmers, Klaus; Metges, Cornelia C; Kuhla, Björn

2018-03-28

Increasing the dietary fat content of ruminant diets decreases methane (CH 4 ) production. This effect is caused by the toxic properties of fatty acids on rumen microbial populations, coating of feed particles diminishing the accessibility for microbes, and a reduction in dry matter intake (DMI). The latter effect is caused by postabsorptive long-chain fatty acids eliciting anorexic signaling; however, whether circulating long-chain fatty acids affect rumen CH 4 production alike is unknown. To approach this question, 5 rumen-cannulated Holstein cows in late lactation received 2 jugular catheters and were kept in respiration chambers to measure CH 4 production and DMI for 48 h. In a crossover design, cows were intravenously infused with a 20% lipid emulsion (LIPO) or 0.9% NaCl (CON). The LIPO cows received 2.1 kg of triglycerides/d [0.152 ± 0.007 g of triglycerides/(kg of BW × h) -1 ] consisting of 12.1% palmitic acid, 4.2% stearic acid, 31.1% oleic acid, and 52.7% linoleic acid. Blood and rumen fluid samples were taken hourly during the day. Results showed that LIPO compared with CON infusion increased plasma triglyceride as well as free fatty acid and serotonin concentrations but reduced the proportion of de novo synthesized milk fatty acids (sum of C6 to C16). Daily CH 4 production and DMI were lower, whereas daily CH 4 yield (CH 4 /DMI) was greater in LIPO than CON cows, although CH 4 yield decreased from d 1 to d 2 by 2 to 14% in LIPO-infused cows only. This effect was associated with a higher (acetate + butyrate)/propionate ratio, tending lower propionate concentrations between 24 and 34 h of infusion, reduced relative abundances of genera belonging to Succinivibrio, Ruminococcaceae, and Ruminiclostridium, and greater relative Bacteroidetes genus abundances in the rumen. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Feed intake is related to changes in plasma nonesterified fatty acid concentration and hepatic acetyl CoA content following feeding in lactating dairy cows.

PubMed

Piantoni, P; Ylioja, C M; Allen, M S

2015-10-01

The relationship between hepatic acetyl CoA (AcCoA) content and dry matter intake (DMI) was evaluated using 28 multiparous Holstein cows; 14 were early postpartum (PP; 12.6 ± 3.8 d in milk) and 14 were late-lactation cows (LL; 269 ± 30 d in milk). Cows were fed once daily, and DMI was determined for the first 4h after feeding. Liver and blood samples were collected before feeding and 4h after feeding. Feed intake over the 4-h period ranged from 3.7 to 9.6 kg of dry matter and was similar for the 2 stages of lactation. Before feeding, hepatic AcCoA content was greater for PP compared with LL cows (34.4 vs. 12.5 nmol/g), and decreased over the 4h after feeding for PP only (28.7 vs. 34.4 nmol/g). The range for change in AcCoA over the 4-h period was wide for both PP (-24.3 to 10.4 nmol/g) and LL (-5.7 to 16.1 nmol/g), and was related negatively to DMI at 4h for both PP (R(2) = 0.55) and LL (R(2) = 0.31). The reduction in plasma NEFA concentration over the 4-h period was greater for PP than LL cows (-681 vs. -47 µEq/L), and was related to DMI at 4h for both PP and LL (both R(2) = 0.38). Greater DMI among cows over the first 4h after feeding might have been from a sharper reduction in supply of AcCoA in the liver for oxidation during meals because of the reduction in plasma NEFA concentration. Consistent with this is that the change in AcCoA was positively related to the reduction in plasma NEFA concentration for PP cows (R(2) = 0.31). However, change in plasma NEFA concentration was not related to change in hepatic AcCoA in LL cows, indicating that the pool of AcCoA in LL cows is not as dependent on NEFA flux to the liver as that of PP cows. Further research is required to determine production and fate of AcCoA within the timeframe of meals and the effects of feeding on energy charge in hepatic tissue. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Type 2 Diabetes and Risk of Hip Fractures and Non-Skeletal Fall Injuries in the Elderly: A Study From the Fractures and Fall Injuries in the Elderly Cohort (FRAILCO).

PubMed

Wallander, Märit; Axelsson, Kristian F; Nilsson, Anna G; Lundh, Dan; Lorentzon, Mattias

2017-03-01

Questions remain about whether the increased risk of fractures in patients with type 2 diabetes (T2DM) is related mainly to increased risk of falling or to bone-specific properties. The primary aim of this study was to investigate the risk of hip fractures and non-skeletal fall injuries in older men and women with and without T2DM. We included 429,313 individuals (aged 80.8 ± 8.2 years [mean ± SD], 58% women) from the Swedish registry "Senior Alert" and linked the data to several nationwide registers. We identified 79,159 individuals with T2DM (45% with insulin [T2DM-I], 41% with oral antidiabetics [T2DM-O], and 14% with no antidiabetic treatment [T2DM-none]) and 343,603 individuals without diabetes. During a follow-up of approximately 670,000 person-years, we identified in total 36,132 fractures (15,572 hip fractures) and 20,019 non-skeletal fall injuries. In multivariable Cox regression models where the reference group was patients without diabetes and the outcome was hip fracture, T2DM-I was associated with increased risk (adjusted hazard ratio (HR) [95% CI] 1.24 [1.16-1.32]), T2DM-O with unaffected risk (1.03 [0.97-1.11]), and T2DM-none with reduced risk (0.88 [0.79-0.98]). Both the diagnosis of T2DM-I (1.22 [1.16-1.29]) and T2DM-O (1.12 [1.06-1.18]) but not T2DM-none (1.07 [0.98-1.16]) predicted non-skeletal fall injury. The same pattern was found regarding other fractures (any, upper arm, ankle, and major osteoporotic fracture) but not for wrist fracture. Subset analyses revealed that in men, the risk of hip fracture was only increased in those with T2DM-I, but in women, both the diagnosis of T2DM-O and T2DM-I were related to increased hip fracture risk. In conclusion, the risk of fractures differs substantially among patients with T2DM and an increased risk of hip fracture was primarily found in insulin-treated patients, whereas the risk of non-skeletal fall injury was consistently increased in T2DM with any diabetes medication. © 2016 American Society for Bone and Mineral Research. © 2016 American Society for Bone and Mineral Research.

Effects of dietary addition of capsicum extract on intake, water consumption, and rumen fermentation of fattening heifers fed a high-concentrate diet.

PubMed

Rodríguez-Prado, M; Ferret, A; Zwieten, J; Gonzalez, L; Bravo, D; Calsamiglia, S

2012-06-01

Four beef Holstein heifers (BW = 438 ± 71 kg) fitted with a 1-cm i.d. plastic ruminal trocars were used in a 4 × 4 Latin square design to evaluate the effect of 3 doses of capsicum extract (CAP) on intake, water consumption, and ruminal fermentation in heifers fed a high-concentrate diet. Animals were fed (DM basis) 10% barley straw and 90% concentrate (32.2% barley grain, 27.9% ground corn, 7.5% wheat bran, 10.7% soybean meal, 10.7% soybean hulls, 7.2% corn gluten feed, 3.1% mineral-vitamin mix; 16.6% CP, 18.3% NDF). Treatments were no additive (CTR), 125 (CAP125), 250 (CAP250), and 500 (CAP500) mg/d of capsicum oleoresin standardized with 6% of capsaicin and dihydrocapsaicin (XTract 6933, Pancosma, Geneva, Switzerland). Each experimental period consisted of 25 d (15 d for adaptation, 5 d of continuous measurement of DMI, and 3 d for rumen sample collection). Animals had ad libitum access to water and feed offered once daily at 0800 h. Data were analyzed by the MIXED procedure of SAS. The model included the fixed effects of period and treatment, the random effect of heifer, and the residual error. The effects were tested for linear and quadratic effects. A linear response was observed (CTR, CAP125, CAP250, and CAP500, respectively) for DMI (8.56, 9.84, 8.68, and 9.40 kg/d; P < 0.04), ruminal pH (6.03, 5.84, 5.96, and 5.86; P < 0.08) and total VFA (134.3, 144.8, 140.1, and 142.8 mM; P < 0.08). There was a strong correlation between water consumption and DMI (R(2) = 0.98). Dry matter intake in the first 2 h after feeding was reduced (P < 0.05) in all CAP treatments compared with control. The molar proportion of acetate tended to decrease linearly (from 59.6 to 55.5 mol/100 mol; P < 0.06), and ammonia N concentration tended to increase linearly (from 14.4 to 16.0 mg N/dL; P < 0.08). In contrast, the molar proportion of propionate (23.8 mol/100 mol), butyrate (14.2 mol/100 mol), and lactate (0.28 mol/100 mol) were not affected by treatments. Results indicate that capsicum extract stimulated DMI and modified the pattern of DMI in beef cattle fed high concentrate diets.

Noradrenergic facilitation of shock-probe defensive burying in lateral septum of rats, and modulation by chronic treatment with desipramine.

PubMed

Bondi, Corina O; Barrera, Gabriel; Lapiz, M Danet S; Bedard, Tania; Mahan, Amy; Morilak, David A

2007-03-30

We have previously shown that acute stress-induced release of norepinephrine (NE) facilitates anxiety-like behavioral responses to stress, such as reduction in open-arm exploration on the elevated-plus maze and in social behavior on the social interaction test. Since these responses represent inhibition of ongoing behavior, it is important to also address whether NE facilitates a response that represents an activation of behavior. Correspondingly, it is unknown how a chronic elevation in tonic steady-state noradrenergic (NA) neurotransmission induced by NE reuptake blockade might alter this acute modulatory function, a regulatory process that may be pertinent to the anxiolytic effects of NE reuptake blockers such as desipramine (DMI). Therefore, in this study, we investigated noradrenergic modulation of the shock-probe defensive burying response in the lateral septum (LS). In experiment 1, shock-probe exposure induced an acute 3-fold increase in NE levels measured in LS of male Sprague-Dawley rats by microdialysis. Shock-probe exposure also induced a modest rise in plasma ACTH, taken as an indicator of perceived stress, that returned to baseline more rapidly in rats that were allowed to bury the probe compared to rats prevented from burying by providing them with minimal bedding, indicating that the active defensive burying behavior is an effective coping strategy that reduces the impact of acute shock probe-induced stress. In experiment 2, blockade of either alpha(1)- or beta-adrenergic receptors in LS by local antagonist microinjection immediately before testing reduced defensive burying and increased immobility. In the next experiment, chronic DMI treatment increased basal extracellular NE levels in LS, and attenuated the acute shock probe-induced increase in NE release in LS relative to baseline. Chronic DMI treatment decreased shock-probe defensive burying behavior in a time-dependent manner, apparent only after 2 weeks or more of drug treatment. Moreover, rats treated chronically with DMI showed no significant rise of plasma ACTH in response to shock-probe exposure. Thus, acute stress-induced release of NE in LS facilitated defensive burying, an active, adaptive behavioral coping response. Chronic treatment with the NE reuptake blocker and antidepressant drug DMI attenuated acute noradrenergic facilitation of the active burying response, and also attenuated the level of perceived stress driving that response. These results suggest that long-term regulation of the acute modulatory function of NE by chronic treatment with reuptake blockers may contribute to the mechanisms by which such drugs exert their anxiolytic effects in the treatment of stress-related psychiatric conditions, including depression and anxiety.

A method for estimating dry forage intake by sheep using polyethylene glycol as a faecal marker measured with NIRS.

PubMed

Hassoun, P; Viudes, G; Autran, P; Bastianelli, D; Bocquier, F

2013-08-01

In experiments based on ruminants' individual dry matter intake (DMI) assessment, several external markers can be used to estimate faecal output when total faeces collection is not possible. However, preparation of the markers to be administered and analytical procedures used for marker content determination are time-consuming thus strongly limiting the number of animals involved in the experiments. In this paper, polyethylene glycol (PEG, molecular weight 6000 da) was tested as a faecal marker. Four trials were conducted on dry, non-lactating ewes kept in digestibility crates that allowed individual measurements. The overall experiment was designed to assess the major factors that could lessen the effectiveness of this method, assuming that the use of grab samples of faeces is sufficient. Trial 1 was designed to test two levels of PEG (20 and 40 g/day) administered in two equal amounts. Trial 2 was designed to test the effect of either a single morning (0800 h) dose (20 g/day) or a twice daily administration (0800 and 1600 h) of the same fractionated dose. Trial 3 was designed to test a 20 g/day dose of PEG administered once daily to ewes fed with hays of different qualities: medium (MH) and low (LH). In trial 4, a lower dose of PEG (10 g/day) was administered once a day to ewes fed with fresh oat-vetch forage. It was demonstrated that PEG could be precisely estimated (average prediction error = 3.47 g/kg) with near-infrared reflectance spectroscopy (NIRS). On the basis of the four trials, it has been proved that PEG administration (20 and 40 g/day) did not significantly affect the DMI of ewes fed dry diets (trials 1, 2 and 3), whereas there was an unexpected increase of DMI for ewes fed exclusively with green feed (trial 4) without DM digestibility modification. Providing PEG as a single dose (0800 h) or split into two equal parts (0800 and 1600 h) did not alter the estimated DMI. Considering the interest of grab sampling, there were clear variations of PEG in faeces with higher concentrations observed at 0800 and 1600 h and lower concentrations at 1400 h. Consequently, with PEG (measured with NIRS) administered once and using the grab sampling procedure (morning collection), it is possible to estimate the DMI of dry feeds with good accuracy. For green feeds, more research is needed as the estimated results are still highly variable.

Molecular and biochemical analysis of symbiotic plant receptor kinase complexes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cook, Douglas R; Riely, Brendan K

DE-FG02-01ER15200 was a 36-month project, initiated on Sept 1, 2005 and extended with a one-year no cost extension to August 31, 2009. During the project period we published seven manuscripts (2 in review). Including the prior project period (2002-2005) we published 12 manuscripts in journals that include Science, PNAS, The Plant Cell, Plant Journal, Plant Physiology, and MPMI. The primary focus of this work was to further elucidate the function of the Nod factor signaling pathway that is involved in initiation of the legume-rhizobium symbiosis and in particular to explore the relationship between receptor kinase-like proteins and downstream effectors ofmore » symbiotic development. During the project period we have map-base cloned two additional players in symbiotic development, including an ERF transcription factor and an ethylene pathway gene (EIN2) that negatively regulates symbiotic signaling; we have also further characterized the subcellular distribution and function of a nuclear-localized symbiosis-specific ion channel, DMI1. The major outcome of the work has been the development of systems for exploring and validating protein-protein interactions that connect symbiotic receptor-like proteins to downstream responses. In this regard, we have developed both homologous (i.e., in planta) and heterologous (i.e., in yeast) systems to test protein interactions. Using yeast 2-hybrid screens we isolated the only known interactor of the nuclear-localized calcium-responsive kinase DMI3. We have also used yeast 2-hybrid methodology to identify interactions between symbiotic signaling proteins and certain RopGTPase/RopGEF proteins that regulate root hair polar growth. More important to the long-term goals of our work, we have established a TAP tagging system that identifies in planta interactions based on co-immuno precipitation and mass spectrometry. The validity of this approach has been shown using known interactors that either co-iummnoprecipate (i.e., remorin) or co-localize (i.e., the flotillin FLOT4) with symbiotic receptor-like proteins. As controls for TAP tag analysis we have generated protein isoforms that carry fluorescent domains (translational fusions to GFP) and these have been used to establish the subcellular location and dynamics of two symbiotic receptors, LYK3 and DMI2. Both proteins localize to membrane microdomains, or putative lipid rafts, and display dynamic behavior following elicitation with the Nod factor ligand. Finally, mass spectrometry of interacting proteins is yielding lists of candidate proteins that we are poised to test using semi-high throughput RNAi technology and Tnt1 knockout collections in Medicago truncatula.« less

Effect of reduced ferulate-mediated lignin/arabinoxylan cross-linking in corn silage on feed intake, digestibility, and milk production.

PubMed

Jung, H G; Mertens, D R; Phillips, R L

2011-10-01

Cross-linking of lignin to arabinoxylan by ferulates limits in vitro rumen digestibility of grass cell walls. The effect of ferulate cross-linking on dry matter intake (DMI), milk production, and in vivo digestibility was investigated in ad libitum and restricted-intake digestion trials with lambs, and in a dairy cow performance trial using the low-ferulate sfe corn mutant. Silages of 5 inbred corn lines were fed: W23, 2 W23sfe lines (M04-4 and M04-21), B73, and B73bm3. As expected, the W23sfe silages contained fewer ferulate ether cross-links and B73bm3 silage had a lower lignin concentration than the respective genetic controls. Silages were fed as the sole ingredient to 4 lambs per silage treatment. Lambs were confined to metabolism crates and fed ad libitum for a 12-d adaptation period followed by a 5-d collection period of feed refusals and feces. Immediately following the ad libitum feeding trial, silage offered was limited to 2% of body weight. After a 2-d adaptation to restricted feeding, feed refusals and feces were collected for 5 d. Seventy Holstein cows were blocked by lactation, days in milk, body weight, and milk production and assigned to total mixed ration diets based on the 5 corn silages. Diets were fed for 28 d and data were collected on weekly DMI and milk production and composition. Fecal grab samples were collected during the last week of the lactation trial for estimation of feed digestibility using acid-insoluble ash as a marker. Silage, total mixed ration, feed refusals, and fecal samples were analyzed for crude protein, starch, neutral detergent fiber (NDF), cell wall polysaccharides, and lignin. The W23sfe silages resulted in lower DMI in the ad libitum trial than the W23 silage, but DMI did not differ in the restricted trial. No differences were observed for NDF or cell wall polysaccharide digestibility by lambs with restricted feeding, but the amount of NDF digested daily increased for lambs fed the M04-21 W23sfe silage ad libitum. Lambs were less selective against NDF and lignin when offered W23sfe silages. The B73bm3 silage did not affect DMI or digestibility of cell walls at the restricted feeding level, but total daily NDF digested was greater at ad libitum intake. Intake, milk production, and cell wall digestibility were greater for cows fed diets containing W23sfe silages than for those fed W23 silage. Although milk production was greater for the B73bm3 diet, DMI and cell wall digestibility were not altered. Cows were less selective against cell wall material when fed both W23sfe and B73bm3 silages. Reduced ferulate cross-linking in sfe corn silage is a new genetic mechanism for improving milk production. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Milk yield, quality, and coagulation properties of 6 breeds of goats: Environmental and individual variability.

PubMed

Vacca, Giuseppe M; Stocco, Giorgia; Dettori, Maria L; Pira, Emanuela; Bittante, Giovanni; Pazzola, Michele

2018-05-09

Goat milk and cheese production is continuously increasing and milk composition and coagulation properties (MCP) are useful tools to predict cheesemaking aptitude. The present study was planned to investigate the extension of lactodynamographic analysis up to 60 min in goat milk, to measure the farm and individual factors, and to investigate differences among 6 goat breeds. Daily milk yield (dMY) was recorded and milk samples collected from 1,272 goats reared in 35 farms. Goats were of 6 different breeds: Saanen and Camosciata delle Alpi for the Alpine type, and Murciano-Granadina, Maltese, Sarda, and Sarda Primitiva for the Mediterranean type. Milk composition (fat, protein, lactose, pH; somatic cell score; logarithmic bacterial count) and MCP [rennet coagulation time (RCT, min), curd-firming time (k 20 , min), curd firmness at 30, 45, and 60 min after rennet addition (a 30 , a 45 , and a 60 , mm)] were recorded, and daily fat and protein yield (dFPY g/d) was calculated as the sum of fat and protein concentration multiplied by the dMY. Data were analyzed using different statistical models to measure the effects of farm, parity, stage of lactation and breed; lastly, the direct and the indirect effect of breed were quantified by comparing the variance of breed from models with or without the inclusion of linear regression of fat, protein, lactose, pH, bacterial, somatic cell counts, and dMY. Orthogonal contrasts were performed to compare least squares means. Almost all traits exhibited high variability, with coefficients of variation between 32 (for RCT) and 63% (for a 30 ). The proportion of variance regarding dMY, dFPY, and milk composition due to the farm was moderate, whereas for MCP it was low, except for a 60 , at 69%. Parity affected both yield and quality traits of milk, with least squares means of dMY and dFPY showing an increase and RCT and curd firmness traits a decrease from the first to the last parity class. All milk quality traits, excluding fat, were affected by the stage of lactation; RCT and k 20 decreased rapidly and a 30 was higher from the first to the last part of lactation. Alpine breeds showed the highest dMY and dFPY but Mediterranean the best percentage of protein, fat, and lactose and a shorter k 20 and a greater a 30 . Among the Mediterranean goats, Murciano-Granadina goats had the highest milk yield, fat, and protein contents, whereas Maltese, Sarda, and Sarda Primitiva were characterized by much more favorable technological properties in terms of k 20 , a 30 , and a 45 . In conclusion, as both the farm and individual factors highly influenced milk composition and MCP traits, improvements of these traits should be based both on modifying management and individual goat factors. As expected, several differences were attributable to the breed effect, with the best milk production for the Alpines and milk quality and coagulation for the Mediterranean goats. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

46 CFR 164.009-11 - Furnace apparatus.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Furnace apparatus. 164.009-11 Section 164.009-11 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... apparatus. (a) The test furnace apparatus consists of a furnace tube, stabilizer, draft shield, furnace...

46 CFR 164.009-11 - Furnace apparatus.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Furnace apparatus. 164.009-11 Section 164.009-11 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS... apparatus. (a) The test furnace apparatus consists of a furnace tube, stabilizer, draft shield, furnace...

Development of a Hot Working Steel Based on a Controlled Gas-Metal-Reaction

NASA Astrophysics Data System (ADS)

Ritzenhoff, Roman; Gharbi, Mohammad Malekipour

As a result of cost sensitiveness, the demand on hot working steels with advanced characteristics and properties are ascending. We have used a controlled gas-metal-reaction in a P-ESR furnace to produce high quality hot working steel. These types of materials are also known as High Nitrogen Steels (HNS). An overview of the development in a pressurized induction furnace to the final industrial scale using P-ESR will be provided. Different heat treatment strategies are conducted and their effect on mechanical properties is investigated.

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4) Dross furnace charging location; (5) Blast furnace and dross furnace tapping location; (6) Sinter machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) The...

Hund's Rule-Driven Dzyaloshinskii-Moriya Interaction at 3d-5d Interfaces.

PubMed

Belabbes, A; Bihlmayer, G; Bechstedt, F; Blügel, S; Manchon, A

2016-12-09

Using relativistic first-principles calculations, we show that the chemical trend of the Dzyaloshinskii-Moriya interaction (DMI) in 3d-5d ultrathin films follows Hund's first rule with a tendency similar to their magnetic moments in either the unsupported 3d monolayers or 3d-5d interfaces. We demonstrate that, besides the spin-orbit coupling (SOC) effect in inversion asymmetric noncollinear magnetic systems, the driving force is the 3d orbital occupations and their spin-flip mixing processes with the spin-orbit active 5d states control directly the sign and magnitude of the DMI. The magnetic chirality changes are discussed in the light of the interplay between SOC, Hund's first rule, and the crystal-field splitting of d orbitals.

Magnon Hall effect on the Lieb lattice.

PubMed

Cao, Xiaodong; Chen, Kai; He, Dahai

2015-04-29

Ferromagnetic insulators without inversion symmetry may show magnon Hall effect (MHE) in the presence of a temperature gradient due to the existence of Dzyaloshinskii-Moriya interaction (DMI). In this theoretical study, we investigate MHE on a lattice with inversion symmetry, namely the Lieb lattice, where the DMI is introduced by adding an external electric field. We show the nontrivial topology of this model by examining the existence of edge states and computing the topological phase diagram characterized by the Chern numbers of different bands. Together with the topological phase diagram, we can further determine the sign and magnitude of the transverse thermal conductivity. The impact of the flat band possessed by this model on the thermal conductivity is discussed by computing the Berry curvature analytically.

Assessing energy efficiency of electric car bottom furnaces intended for thermal energization of minerals

NASA Astrophysics Data System (ADS)

Nizhegorodov, A. I.

2017-01-01

The paper deals with a new concept of electric furnaces for roasting and thermal energization of vermiculite and other minerals with vibrational transportation of a single-layer mass under constant thermal field. The paper presents performance calculation and comparative assessment of energy data for furnaces of different modifications: flame and electric furnaces with three units, furnaces with six units and ones with series-parallel connection of units, and furnaces of new concept.

Analysis of thermal radiation in coal-fired furnaces

NASA Astrophysics Data System (ADS)

Miles, Jonathan J.; Hammaker, Robert G.; Madding, Robert P.; Sunderland, J. E.

1997-04-01

Many utilities throughout the United States have added infrared scanning to their arsenal of techniques for inspection and predictive maintenance programs. Commercial infrared scanners are not designed, however, to withstand the searing interiors of boilers, which can exceed 2500 degrees Fahrenheit. Two high-temperature lenses designed to withstand the hostile environment inside a boiler for extended periods of time were developed by the EPRI M&D Center, thus permitting real-time measurement of steam tube temperatures and subsequent analysis of tube condition, inspection of burners, and identification of hot spots. A study was conducted by Sunderland Engineering, Inc. and EPRI M&D in order to characterize the radiative interactions that affect infrared measurements made inside a commercial, coal- fired, water-tube boiler. A comprehensive literature search exploring the existing record of results pertaining to analytical and experimental determination of radiative properties of coal-combustion byproducts was performed. An experimental component intended to provide data for characterization of the optical properties of hot combustion byproducts inside a coal-fired furnace was carried out. The results of the study indicate that hot gases, carbon particles, and fly ash, which together compose the medium inside a boiler, affect to varying degrees the transport of infrared radiation across a furnace. Techniques for improved infrared measurement across a coal-fired furnace are under development.

A Plenoptic Multi-Color Imaging Pyrometer

NASA Technical Reports Server (NTRS)

Danehy, Paul M.; Hutchins, William D.; Fahringer, Timothy; Thurow, Brian S.

2017-01-01

A three-color pyrometer has been developed based on plenoptic imaging technology. Three bandpass filters placed in front of a camera lens allow separate 2D images to be obtained on a single image sensor at three different and adjustable wavelengths selected by the user. Images were obtained of different black- or grey-bodies including a calibration furnace, a radiation heater, and a luminous sulfur match flame. The images obtained of the calibration furnace and radiation heater were processed to determine 2D temperature distributions. Calibration results in the furnace showed that the instrument can measure temperature with an accuracy and precision of 10 Kelvins between 1100 and 1350 K. Time-resolved 2D temperature measurements of the radiation heater are shown.

List of EPA Certified Forced-Air Furnaces

EPA Pesticide Factsheets

The EPA-Certified Forced-Air Furnace list contains EPA-certified forced-air furnaces that meet the 2015 NSPS for New Residential Wood Heaters, New Residential Hydronic Heaters and Forced-Air Furnaces.

10 CFR 430.32 - Energy and water conservation standards and their effective dates.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (excluding classes noted below) 78 (B) Mobile Home furnaces 75 (C) Small furnaces (other than those designed solely for installation in mobile homes) having an input rate of less than 45,000 Btu/hr (1) Weatherized... including mobile home furnaces) 80 (B) Mobile Home gas furnaces 80 (C) Non-weatherized oil-fired furnaces...

10 CFR 430.32 - Energy and water conservation standards and their compliance dates.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (excluding classes noted below) 78 (B) Mobile Home furnaces 75 (C) Small furnaces (other than those designed solely for installation in mobile homes) having an input rate of less than 45,000 Btu/hr (1) Weatherized... including mobile home furnaces) 80 (B) Mobile Home gas furnaces 80 (C) Non-weatherized oil-fired furnaces...

10 CFR 430.32 - Energy and water conservation standards and their effective dates.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (excluding classes noted below) 78 (B) Mobile Home furnaces 75 (C) Small furnaces (other than those designed solely for installation in mobile homes) having an input rate of less than 45,000 Btu/hr (1) Weatherized... including mobile home furnaces) 80 (B) Mobile Home gas furnaces 80 (C) Non-weatherized oil-fired furnaces...

Design and Construction of a Small Vacuum Furnace

NASA Astrophysics Data System (ADS)

Peawbang, P.; Thedsakhulwong, A.

2017-09-01

The purpose of this research is designed and constructed of a small vacuum furnace. A cylindrical graphite was chosen as the material of the furnace, the cylinder aluminium and copper sheets were employed to prevent the heat radiation that transfers from the furnace to the chamber wall. A rotary pump used, the pressure of graphite furnace can be pumped up to 30 mTorr and heated up to 700 °C driving by wire and the temperature of the chamber wall is relatively remained too low. In addition, heat loss obtained from the graphite furnace by conduction, convection, and radiation were analyzed. The dominating heat loss was found to be caused by the blackbody radiation, which can thus be used to estimate the relationship between graphite furnace temperature and the drive power needed. The cylindrical graphite furnace has an inner diameter of 44 mm, the outer diameter of 60 mm and 45 mm in height, the 355.5 W of power is needed to drive the furnace to 700 °C.

Development of high performance refractory fibers with enhanced insulating properties and longer service lifetimes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Martin, P.C.; DePoorter, G.L.; Munoz, D.R.

1991-02-01

We have initiated a three phase investigation of the development of high performance refractory fibers with enhanced insulating properties and longer usable lifetimes. This report presents the results of the first phase of the study, performed from Aug. 1989 through Feb. 1991, which shows that significant energy saving are possible through the use of high temperature insulating fibers that better retain their efficient insulating properties during the service lifetime of the fibers. The remaining phases of this program include the pilot scale development and then full scale production feasibility development and evaluation of enhanced high temperature refractory insulting fibers. Thismore » first proof of principle phase of the program presents a summary of the current use patterns of refractory fibers, a laboratory evaluation of the high temperature performance characteristics of selected typical refractory fibers and an analysis of the potential energy savings through the use of enhanced refractory fibers. The current use patterns of refractory fibers span a wide range of industries and high temperature furnaces within those industries. The majority of high temperature fiber applications are in furnaces operating between 2000 and 26000{degrees}F. The fibers used in furnaces operating within this range provide attractive thermal resistance and low thermal storage at reasonable cost. A series of heat treatment studies performed for this phase of the program has shown that the refractory fibers, as initially manufactured, have attractive thermal conductivities for high temperature applications but the fibers go through rapid devitrification and subsequent crystal growth upon high temperature exposure. Development of improved fibers, maintaining the favorable characteristics of the existing as-manufactured fibers, could save between 1 and 4% of the energy consumed in high temperature furnaces using refractory fibers.« less

Space Station Furnace Facility. Volume 2: Requirements definition and conceptual design study

NASA Technical Reports Server (NTRS)

1992-01-01

The Space Station Freedom Furnace (SSFF) Project is divided into two phases: phase 1, a definition study phase, and phase 2, a design and development phase. TBE was awarded a research study entitled, 'Space Station Furnace Facility Requirements Definition and Conceptual Design Study' on June 2, 1989. This report addresses the definition study phase only. Phase 2 is to be complete after completion of phase 1. The contract encompassed a requirements definition study and culminated in hardware/facility conceptual designs and hardware demonstration development models to test these conceptual designs. The study was divided into two parts. Part 1 (the basic part of the effort) encompassed preliminary requirements definition and assessment; conceptional design of the SSFF Core; fabrication of mockups; and preparation for the support of a conceptional design review (CoDR). Part 2 (the optional part of the effort) included detailed definition of the engineering and design requirements, as derived from the science requirements; refinement of the conceptual design of the SSFF Core; fabrication and testing of the 'breadboards' or development models; and preparation for and support of a requirements definition review.

Oregano Extract Added into the Diet of Dairy Heifers Changes Feeding Behavior and Concentrate Intake

PubMed Central

Kolling, Giovani Jacob; Stumpf, Marcelo Tempel; da Cruz, Eduardo Augusto

2016-01-01

This experiment aimed to describe the effects of Oregano extract (OE) inclusion into the concentrate fed to dairy heifers on physiological parameters, feeding behavior, intake, and performance. Thirty-two Holstein heifers were randomly distributed into four treatments: C = control, without addition of OE; OE2.5 = 2.5 g; OE5.0 = 5.0 g and OE7.5 = 7.5 g of Oregano extract per heifer/day. Feeding behavior and concentrate intake were assessed individually every day and total dry matter intake (DMI) was determined on the last week of the trial. Compared to control group, OE7.5 reduced by 32% the latency time to approach the feed bunk but increased by 6% the time spent eating the concentrate. Each inclusion of 2.5 grams of OE into the concentrate increased the occurrence of postingestive licking the feed bunk with abundant saliva production 1.2 times (P < 0.01) and tended to increase the occurrence of sneeze events 1.2 times (P < 0.10). No statistical difference was detected between treatments for total DMI, but concentrate DMI was 9% lower for OE7.5 when compared to control and OE2.5. The inclusion of 7.5 grams/day of OE causes small but negative effects in feeding behavior and concentrate intake, without change on total dry matter intake. PMID:28116344

Propagation of electromagnetic soliton in a spin polarized current driven weak ferromagnetic nanowire

NASA Astrophysics Data System (ADS)

Senthil Kumar, V.; Kavitha, L.; Gopi, D.

2017-11-01

We investigate the nonlinear spin dynamics of a spin polarized current driven anisotropic ferromagnetic nanowire with Dzyaloshinskii-Moriya interaction (DMI) under the influence of electromagnetic wave (EMW) propagating along the axis of the nanowire. The magnetization dynamics and electromagnetic wave propagation in the ferromagnetic nanowire with weak anti-symmetric interaction is governed by a coupled vector Landau-Lifshitz-Gilbert and Maxwell's equations. These coupled nonlinear vector equations are recasted into the extended derivative nonlinear Schrödinger (EDNLS) equation in the framework of reductive perturbation method. As it is well known, the modulational instability is a precursor for the emergence of localized envelope structures of various kinds, we compute the instability criteria for the weak ferromagnetic nanowire through linear stability analysis. Further, we invoke the homogeneous balance method to construct kink and anti-solitonic like electromagnetic (EM) soliton profiles for the EDNLS equation. We also explore the appreciable effect of the anti-symmetric weak interaction on the magnetization components of the propagating EM soliton. We find that the combination of spin-polarized current and the anti-symmetric DMI have a profound effect on the propagating EMW in a weak ferromagnetic nanowire. Thus, the anti-symmetric DMI in a spin polarized current driven ferromagnetic nanowire supports the lossless propagation of EM solitons, which may have potential applications in magnetic data storage devices.

Retrospective analysis of treatment modalities in diabetic muscle infarction

PubMed Central

Onyenemezu, Ikenna; Capitle, Eugenio

2014-01-01

Background Diabetic muscle infarction (DMI) is a spontaneous necrosis of skeletal muscle of unknown etiology. The major risk factor is longstanding uncontrolled diabetes mellitus (DM). Optimal treatment for DMI is not known. The purpose of this study was to analyze the outcome of surgical treatment, physiotherapy, and bed rest in DMI. Methods We searched Medline from its inception to April 2013. We selected cases that provided sufficient data on recovery duration, recurrences, and non-recurrences. Baseline characteristics, including age, sex, microvascular complications, lesion size estimated on magnetic resonance imaging, type of diabetes, and duration of diabetes were assessed. The primary outcome was mean time to recovery from initial treatment and secondary outcomes were mean time to recurrence and recurrence rate. Results Mean time to recovery was 149 (95% confidence interval [CI] 113–186), 71 (95% CI 47–96), and 43 (95% CI 30–57) days for surgery, physiotherapy and bed rest, respectively. These figures were statistically significant only for surgery versus physiotherapy and surgery versus bed rest (P<0.01). Mean time to recurrence was 30, 107, and 297 days for surgery, physiotherapy, and bed rest, respectively. The recurrence rate was 57%, 44%, and 24% for surgery, physiotherapy, and bed rest, respectively. Conclusion Our results show a similar outcome for physiotherapy as compared with bed rest. It also confirms nonsurgical treatment as a better therapeutic option compared with surgical treatment. PMID:27790029

Effect of the type of silage on milk yield, intake and rumen metabolism of dairy cows grazing swards with low herbage mass.

PubMed

Ruiz-Albarrán, Miguel; Balocchi, Oscar A; Noro, Mirela; Wittwer, Fernando; Pulido, Rubén G

2016-07-01

The aim of this study was to evaluate the effect of herbage allowance (HA) and type of silage supplemented (TS) on milk yield, dry matter intake (DMI) and metabolism of dairy cows in early lactation. Thirty-six Holstein-Friesian dairy cows were allocated to four treatments derived from an arrangement of two HA (LHA = 17 or HHA = 25 kg of DM/cow/day) and two TS (grass (GS) or maize (MS)). Herbage allowance had no effect on DMI or milk yield. Rumen pH and NH3 -N concentration were not affected by HA. The efficiency of microbial protein synthesis in the rumen (microbial protein (MP)) was affected by HA with 21.5 and 23.9 g microbial nitrogen per kg ruminal digestible organic matter for LHA and HHA, respectively (P < 0.05). Supplementation with MS showed higher values of milk yield by 2.4 kg/cow/day (P < 0.001), milk protein content by 0.10 % (P < 0.023) and herbage DMI by 2.2 kg/cow/day, and showed lower values for milk urea compared to GS (P < 0.001). The former results suggest that TS had a greater effect on milk yield, total feed intake and energy intake than increase in herbage allowance; however, increase in HA had greater effects on MP than TS. © 2015 Japanese Society of Animal Science.

The Effect of Concentrate Supplementation on Creatinine Excretion in Thin-Tailed Lambs and Sheep

NASA Astrophysics Data System (ADS)

Purnami, N. A.; Prima, A.

2018-02-01

An experimental study was carried out to examine the effect of concentrates supplementation on creatinine excretion in lambs and sheep. The study used 8 male thin tailed lambs (aged ±3-4 months, weighed ±15.20 kg) and 8 sheep (aged ±1 year and weighed ±22.71kg). The animals were fed the diet contained 100% napier grass (100G) and 50% napier grass 50% concentrate as much as 3.5% of body weight (50G50C). This study used a complete randomized nested design. The parameters observed were dry matter intake (DMI) and creatinine excretion. The results showed that the diet significantly affect (P<0.05) DMI. The consumption of 100G was lower than that of 50G50C both lambs (0.32 vs 0.62 kg/d) and sheep (0.47 vs 0.88 kg/d). On the other hand, the diet did not affect the creatinine excretion (P 0.05) either G100 or G50C50 in lambs or sheep. However, the creatinine excretion in sheep (185.66 mg/d) was higher than that of lambs (299.1 md/d) (P<0.05). It can be concluded that concentrate supplementation of grass diet increased DMI but did not affect creatinine excretion. The creatinine excretion of sheep was higher than that of lambs .

High-Flux Solar Furnace Facility | Concentrating Solar Power | NREL

Science.gov Websites

High-Flux Solar Furnace Facility High-Flux Solar Furnace Facility NREL's High-Flux Solar Furnace (HFSF) is a 10-kW optical furnace for testing high-temperature processes or applications requiring high range of technologies with a diverse set of experimental requirements. The high heating rates create the

20. Detail, Furnace A, shows the drill used to tap ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. Detail, Furnace A, shows the drill used to tap the furnace (at center left) and the 'mud gun' used to close it up with a clay plug (at lower right). Metal chute at center (next to drill) was used to clean out furnace prior to its abandonment. - Central Furnaces, 2650 Broadway, east bank of Cuyahoga River, Cleveland, Cuyahoga County, OH

Looking Northwest at Furnace Control Panels and Gas Control Furnace ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking Northwest at Furnace Control Panels and Gas Control Furnace in Red Room Within Recycle Recovery Building - Hematite Fuel Fabrication Facility, Recycle Recovery Building, 3300 State Road P, Festus, Jefferson County, MO

Furnace devices aerodynamics optimization for fuel combustion efficiency improvement and nitrogen oxide emission reduction

NASA Astrophysics Data System (ADS)

Volkov, E. P.; Prokhorov, V. B.; Arkhipov, A. M.; Chernov, S. L.; Kirichkov, V. S.; Kaverin, A. A.

2017-11-01

MPEI conducts researches on physical and mathematical models of furnace chambers for improvement of power-generation equipment fuel combustion efficiency and ecological safety. Results of these researches are general principles of furnace aerodynamics arrangement for straight-flow burners and various fuels. It has been shown, that staged combustion arrangement with early heating and igniting with torch distribution in all furnace volume allows to obtain low carbon in fly ash and nitrogen oxide emission and also to improve boiler operation reliability with expand load adjustment range. For solid fuel combustion efficiency improvement it is practical to use high-placed and strongly down-tilted straight-flow burners, which increases high-temperature zone residence time for fuel particles. In some cases, for this combustion scheme it is possible to avoid slag-tap removal (STR) combustion and to use Dry-bottom ash removal (DBAR) combustion with tolerable carbon in fly ash level. It is worth noting that boilers with STR have very high nitrogen oxide emission levels (1200-1800 mg/m3) and narrow load adjustment range, which is determined by liquid slag output stability, so most industrially-developed countries don’t use this technology. Final decision about overhaul of boiler unit is made with regard to physical and mathematical modeling results for furnace and zonal thermal calculations for furnace and boiler as a whole. Overhaul of boilers to provide staged combustion and straight-flow burners and nozzles allows ensuring regulatory nitrogen oxide emission levels and corresponding best available technology criteria, which is especially relevant due to changes in Russian environmental regulation.

Power quality analysis of DC arc furnace operation using the Bowman model for electric arc

NASA Astrophysics Data System (ADS)

Gherman, P. L.

2018-01-01

This work is about a relatively new domain. The DC electric arc is superior to the AC electric arc and it’s not used in Romania. This is why we analyzed the work functions of these furnaces by simulation and model checking of the simulation results.The conclusions are favorable, to be carried is to develop a real-time control system of steel elaboration process.

Real-time control data wrangling for development of mathematical control models of technological processes

NASA Astrophysics Data System (ADS)

Vasilyeva, N. V.; Koteleva, N. I.; Fedorova, E. R.

2018-05-01

The relevance of the research is due to the need to stabilize the composition of the melting products of copper-nickel sulfide raw materials in the Vanyukov furnace. The goal of this research is to identify the most suitable methods for the aggregation of the real time data for the development of a mathematical model for control of the technological process of melting copper-nickel sulfide raw materials in the Vanyukov furnace. Statistical methods of analyzing the historical data of the real technological object and the correlation analysis of process parameters are described. Factors that exert the greatest influence on the main output parameter (copper content in matte) and ensure the physical-chemical transformations are revealed. An approach to the processing of the real time data for the development of a mathematical model for control of the melting process is proposed. The stages of processing the real time information are considered. The adopted methodology for the aggregation of data suitable for the development of a control model for the technological process of melting copper-nickel sulfide raw materials in the Vanyukov furnace allows us to interpret the obtained results for their further practical application.

6. Photocopied August 1978. LINEUP OF HORRY ROTARY FURNACES ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Photocopied August 1978. LINE-UP OF HORRY ROTARY FURNACES ON THE SECOND FLOOR OF THE MICHIGAN LAKE SUPERIOR POWER COMPANY POWER HOUSE. THE HOPPERS WHICH FED THE RAW MATERIALS INTO THE FURNACES ARE SHOWN ABOVE THE FURNACES. AS THE 'SPOOL' OF THE FURNACE ROTATED PAST THE ELECTRODES PLATES WERE ADDED TO HOLD THE FINISHED PRODUCT AND THE DESCENDING RAW MATERIALS IN PLACE. THE DIRECTION OF ROTATION OF THE FURNACES SHOWN IN THIS PHOTO IS CLOCKWISE, (M). - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

Combustion and NOx emission characteristics with respect to staged-air damper opening in a 600 MWe down-fired pulverized-coal furnace under deep-air-staging conditions.

PubMed

Kuang, Min; Li, Zhengqi; Wang, Zhihua; Jing, Xinjing; Liu, Chunlong; Zhu, Qunyi; Ling, Zhongqian

2014-01-01

Deep-air-staging combustion conditions, widely used in tangential-fired and wall-arranged furnaces to significantly reduce NOx emissions, are premature up to now in down-fired furnaces that are designed especially for industry firing low-volatile coals such as anthracite and lean coal. To uncover combustion and NOx emission characteristics under deep-air-staging conditions within a newly operated 600 MWe down-fired furnace and simultaneously understand the staged-air effect on the furnace performance, full-load industrial-size measurements taken of gas temperatures and species concentrations in the furnace, CO and NOx emissions in flue gas, and carbon in fly ash were performed at various staged-air damper openings of 10%, 20%, 30%, and 50%. Increasing the staged-air damper opening, gas temperatures along the flame travel (before the flame penetrating the staged-air zone) increased initially but then decreased, while those in the staged-air zone and the upper part of the hopper continuously decreased and increased, respectively. On opening the staged-air damper to further deepen the air-staging conditions, O2 content initially decreased but then increased in both two near-wall regions affected by secondary air and staged air, respectively, whereas CO content in both two regions initially increased but then decreased. In contrast to the conventional understanding about the effects of deep-air-staging conditions, here increasing the staged-air damper opening to deepen the air-staging conditions essentially decreased the exhaust gas temperature and carbon in fly ash and simultaneously increased both NOx emissions and boiler efficiency. In light of apparently low NOx emissions and high carbon in fly ash (i.e., 696-878 mg/m(3) at 6% O2 and 9.81-13.05%, respectively) developing in the down-fired furnace under the present deep-air-staging conditions, further adjustments such as enlarging the staged-air declination angle to prolong pulverized-coal residence times in the furnace should be considered to improve the deep-air-staging combustion configuration.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carpenter, J.A.; Swanson, D.E; Chango, R.F.

Bethlehem Steel's Burns Harbor Div. operates two 89,000-cu ft blast furnaces, D and C, built in 1969 and 1972. These furnaces have been in the forefront of blast furnace performance since they were blown-in. To maintain a credible operation throughout the past 25 years their performance has been improved continuously. Production was increased approximately 3%/year while fuel rate decreased 1%/year. This presentation summarizes the early repairs, relines and improvements that have sustained and enhanced the furnace's performance. The fourth reline of both furnaces will be discussed in detail. As part of the 1991 reline of D furnace its lines weremore » improved and modern penstocks installed. The bosh, tuyere jacket, hearth jacket and both cast floors were replaced. The furnace now has a larger hearth making it easier to control and, liquid level is no longer a problem when pulling the wind to shut down. The new cast floor with its increased trough length has much improved separation of slag from iron and lowered refractory consumption. Since the cast floors on D furnace were changed, there has been a reduction in accidents and absenteeism. This may be related to the change in work practices on the new cast floors. The 1994 reline of C furnace incorporates those improvements made on D furnace in 1991. In addition, C furnace will have high-density cooling which is expected to double its campaign from 6 to 12 years, without interim repairs.« less

Exothermic furnace module development. [space processing

NASA Technical Reports Server (NTRS)

Darnell, R. R.; Poorman, R. M.

1982-01-01

An exothermic furnace module was developed to rapidly heat and cool a 0.820-in. (2.1 cm) diameter by 2.75-in. (7.0 cm) long TZM molybdenum alloy crucible. The crucible contains copper, oxygen, and carbon for processing in a low-g environment. Peak temperatures of 1270 C were obtainable 3.5 min after start of ignition, and cooling below 950 C some 4.5 min later. These time-temperature relationships were conditioned for a foam-copper experiment, Space Processing Applications Rocket experiment 77-9, in a sounding rocket having a low-g period of 5 min.

CFD Modeling of Flow, Temperature, and Concentration Fields in a Pilot-Scale Rotary Hearth Furnace

NASA Astrophysics Data System (ADS)

Liu, Ying; Su, Fu-Yong; Wen, Zhi; Li, Zhi; Yong, Hai-Quan; Feng, Xiao-Hong

2014-01-01

A three-dimensional mathematical model for simulation of flow, temperature, and concentration fields in a pilot-scale rotary hearth furnace (RHF) has been developed using a commercial computational fluid dynamics software, FLUENT. The layer of composite pellets under the hearth is assumed to be a porous media layer with CO source and energy sink calculated by an independent mathematical model. User-defined functions are developed and linked to FLUENT to process the reduction process of the layer of composite pellets. The standard k-ɛ turbulence model in combination with standard wall functions is used for modeling of gas flow. Turbulence-chemistry interaction is taken into account through the eddy-dissipation model. The discrete ordinates model is used for modeling of radiative heat transfer. A comparison is made between the predictions of the present model and the data from a test of the pilot-scale RHF, and a reasonable agreement is found. Finally, flow field, temperature, and CO concentration fields in the furnace are investigated by the model.

Robofurnace: A semi-automated laboratory chemical vapor deposition system for high-throughput nanomaterial synthesis and process discovery

PubMed Central

Oliver, C. Ryan; Westrick, William; Koehler, Jeremy; Brieland-Shoultz, Anna; Anagnostopoulos-Politis, Ilias; Cruz-Gonzalez, Tizoc; Hart, A. John

2013-01-01

Laboratory research and development on new materials, such as nanostructured thin films, often utilizes manual equipment such as tube furnaces due to its relatively low cost and ease of setup. However, these systems can be prone to inconsistent outcomes due to variations in standard operating procedures and limitations in performance such as heating and cooling rates restrict the parameter space that can be explored. Perhaps more importantly, maximization of research throughput and the successful and efficient translation of materials processing knowledge to production-scale systems, relies on the attainment of consistent outcomes. In response to this need, we present a semi-automated lab-scale chemical vapor deposition (CVD) furnace system, called “Robofurnace.” Robofurnace is an automated CVD system built around a standard tube furnace, which automates sample insertion and removal and uses motion of the furnace to achieve rapid heating and cooling. The system has a 10-sample magazine and motorized transfer arm, which isolates the samples from the lab atmosphere and enables highly repeatable placement of the sample within the tube. The system is designed to enable continuous operation of the CVD reactor, with asynchronous loading/unloading of samples. To demonstrate its performance, Robofurnace is used to develop a rapid CVD recipe for carbon nanotube (CNT) forest growth, achieving a 10-fold improvement in CNT forest mass density compared to a benchmark recipe using a manual tube furnace. In the long run, multiple systems like Robofurnace may be linked to share data among laboratories by methods such as Twitter. Our hope is Robofurnace and like automation will enable machine learning to optimize and discover relationships in complex material synthesis processes. PMID:24289435

Higher-dimensional Wannier Interpolation for the Modern Theory of the Dzyaloshinskii-Moriya Interaction: Application to Co-based Trilayers

NASA Astrophysics Data System (ADS)

Hanke, Jan-Philipp; Freimuth, Frank; Blügel, Stefan; Mokrousov, Yuriy

2018-04-01

We present an advanced first-principles formalism to evaluate the Dzyaloshinskii-Moriya interaction (DMI) in its modern theory as well as Berry curvatures in complex spaces based on a higher-dimensional Wannier interpolation. Our method is applied to the Co-based trilayer systems IrδPt1-δ/Co/Pt and AuγPt1-γ/Co/Pt, where we gain insights into the correlations between the electronic structure and the DMI, and we uncover prominent sign changes of the chiral interaction with the overlayer composition. Beyond the discussed phenomena, the scope of applications of our Wannier-based scheme is particularly broad as it is ideally suited to study efficiently the Hamiltonian evolution under the slow variation of very general parameters.

Annealing effect on current-driven domain wall motion in Pt/[Co/Ni] wire

NASA Astrophysics Data System (ADS)

Furuta, Masaki; Liu, Yang; Sepehri-Amin, Hossein; Hono, Kazuhiro; Zhu, Jian-Gang Jimmy

2017-09-01

The annealing effect on the efficiency of current-driven domain wall motion governed by the spin Hall effect in perpendicularly magnetized Pt/[Co/Ni] wires is investigated experimentally. Important physical parameters, such as the Dzyaloshinskii-Moriya Interaction (DMI), spin Hall angle, and perpendicular anisotropy field strength, for the domain wall motion are all characterized at each annealing temperature. It is found that annealing of wires at temperatures over 120 °C causes significant reduction of the domain wall velocity. Energy dispersive X-ray spectroscopy analysis shows pronounced Co diffusion across the Pt/Co interface resulted from annealing at relatively high temperatures. The combined modeling study shows that the reduction of DMI caused by annealing is mostly responsible for the domain wall velocity reduction due to annealing.

Sealed rotary hearth furnace with central bearing support

DOEpatents

Docherty, James P.; Johnson, Beverly E.; Beri, Joseph

1989-01-01

The furnace has a hearth which rotates inside a stationary closed chamber and is supported therein on vertical cylindrical conduit which extends through the furnace floor and is supported by a single center bearing. The charge is deposited through the furnace roof on the rim of the hearth as it rotates and is moved toward the center of the hearth by rabbles. Externally generated hot gases are introduced into the furnace chamber below the hearth and rise through perforations in the hearth and up through the charge. Exhaust gases are withdrawn through the furnace roof. Treated charge drops from a center outlet on the hearth into the vertical cylindrical conduit which extends downwardly through the furnace floor to which it is also sealed.

Microgravity

NASA Image and Video Library

2001-06-05

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101830, and TBD).

Microgravity

NASA Image and Video Library

2001-06-05

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830).

Microgravity

NASA Image and Video Library

2001-06-05

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. A larger image is available without labels (No. 0101755).

Microgravity

NASA Image and Video Library

2001-06-05

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

40 CFR 63.1541 - Applicability.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., preliminary treatment, refining and casting operations, process fugitive sources, and fugitive dust sources... the blast furnace, electric smelting furnace with a converter or reverberatory furnace, and slag fuming furnace process units. The preliminary treatment process includes the drossing kettles and dross...

2. EXTERIOR VIEW LOOKING SOUTHEAST AT ELECTRIC FURNACE BUILDING AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. EXTERIOR VIEW LOOKING SOUTHEAST AT ELECTRIC FURNACE BUILDING AND ELECTRIC FURNACE OFFICE & CHEMICAL LABORATORY BUILDING. INGOT MOLDS IN RIGHT FOREGROUND. - U.S. Steel Duquesne Works, Electric Furnace Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

The impact of oil burning on kraft recovery furnace SO sub 2 emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Someshwar, A.V.; Pinkerton, J.E.; Caron, A.L.

1991-04-01

Auxiliary fossil fuel, either natural gas or fuel oil, is burned in kraft recovery furnaces during furnace startups and shutdowns, furnace upsets, and periods of substantially reduced rates of black liquor firing. The efficiency of sulfur capture and retention during normal operation of a kraft recovery furnace is inherently high. Consequently, not all the SO{sub 2} from occasional burning of sulfur-containing fuel oil in the furnace would be expected to end up in the stack gases. However, the extent to which such SO{sub 2} is captured by the alkali fume generation processes has not been well documented. In this paper,more » the authors examines the impact that burning oil in kraft recovery furnaces has on the SO{sub 2} emissions. The work included analyses of long-term SO{sub 2} data from a continuous emission monitoring system (CEMS) obtained for four furnaces that burned medium sulfur fuel oil as auxiliary fuel. It also included tests conducted on four furnaces in which varying amounts of oil were co-fired with black liquor.« less

A meta-analysis of lasalocid effects on rumen measures, beef and dairy performance, and carcass traits in cattle.

PubMed

Golder, H M; Lean, I J

2016-01-01

The effects of lasalocid on rumen measures, beef and dairy performance, and carcass traits were evaluated using meta-analysis. Meta-regression was used to investigate sources of heterogeneity. Ten studies (20 comparisons) were used in the meta-analysis on rumen measures. Lasalocid increased total VFA and ammonia concentrations by 6.46 and 1.44 m, respectively. Lasalocid increased propionate and decreased acetate and butyrate molar percentage (M%) by 4.62, 3.18, and 0.83%, respectively. Valerate M% and pH were not affected. Meta-regression found butyrate M% linearly increased with duration of lasalocid supplementation (DUR; = 0.017). When >200 mg/d was fed, propionate and valerate M% were higher and acetate M% was lower ( = 0.042, = 0.017, and = 0.005, respectively). Beef performance was assessed using 31 studies (67 comparisons). Lasalocid increased ADG by 40 g/d, improved feed-to-gain ratio (F:G) by 410 g/kg, and improved feed efficiency (FE; combined measure of G:F and the inverse of F:G). Lasalocid did not affect DMI, but heterogeneity in DMI was influenced by DUR ( = 0.004) and the linear effect of entry BW ( = 0.011). The combination of ≤100 vs. >100 d DUR and entry BW ≤275 vs. >275 kg showed that cattle ≤275 kg at entry fed lasalocid for >100 d had the lowest DMI. Heterogeneity of ADG was influenced by the linear effect of entry BW ( = 0.028) but not DUR. Combining entry BW ≤275 vs. >275 kg and DUR showed that cattle entering at >275 kg fed ≤100 d had the highest ADG. The FE ( = 0.025) and F:G ( = 0.015) linearly improved with dose, and entry BW >275 kg improved F:G ( = 0.038). Fourteen studies (25 comparisons) were used to assess carcass traits. Lasalocid increased HCW by 4.73 kg but not dressing percentage, mean fat cover, or marbling score. Heterogeneity of carcass traits was low and not affected by DUR or dose. Seven studies (11 comparisons) were used to assess dairy performance but the study power was relatively low and the evidence base is limited. Lasalocid decreased DMI in total mixed ration-fed cows by 0.89 kg/d but had no effect on milk yield, milk components, or component yields. Dose linearly decreased DMI ( = 0.049). The DUR did not affect heterogeneity of dairy measures. This work showed that lasalocid improved ADG, HCW, FE, and F:G for beef production. These findings may reflect improved energy efficiency from increased propionate M% and decreased acetate and butyrate M%. Large dairy studies are required for further evaluation of effects of lasalocid on dairy performance.

Effects of a completely pelleted diet on growth performance in Holstein heifers.

PubMed

Bonfante, E; Palmonari, A; Mammi, L; Canestrari, G; Fustini, M; Formigoni, A

2016-12-01

Forage neutral detergent fiber (NDF) content and particle size are important factors that affect rumen function. The aim of the current study was to evaluate the effects on rumen health, NDF digestibility, and animal performance of pelleting a forage-based diet. Eight Holstein heifers (age 336±30d, body weight 346±35kg) were randomly assigned to a repeated crossover design. Animals were housed in tie-stalls and fed for ad libitum intake. The study included 4 periods of 3 wk, the first 2 wk for adaptation to the diet and the last wk for data collection. Diets had the same ingredients but had a different physical form: total mixed ration (TMR) and pellet (diameter=8mm). The physically effective NDF (peNDF) differed between the 2 treatments (39.8 and 11.8% of NDF in the TMR and pellet diets, respectively). During the trial, dry matter intake (DMI), water intake, rumination time, rumen temperature, and pH were evaluated daily. Fecal samples were collected in wk3 of each period to determine total-tract digestibility of the potential digestible (pd)NDF. Average daily gain and feed conversion ratio were calculated at the end of each period. With the pellet diet, DMI, DMI/body weight, and water consumption were higher. We observed no significant difference in average daily gain or feed conversion ratio. Rumination time was lower for the pellet diet than for the TMR diet (241 vs. 507min/d, respectively). Diet had no effect on rumen temperature or rumen pH. The total-tract digestibility of the pdNDF was greater with the TMR diet than with the pellet diet (90.25 vs. 86.82% pdNDF, respectively). The results of the current study suggest that a complete-feed pellet diet was well accepted by the animals, as demonstrated by higher DMI. Rumination time was reduced with the pellet diet, but rumen pH was not different. The pdNDF digestibility was high for both diets, but significantly higher for the TMR diet. Given that animal performance was similar between the 2 diets, although they differed with respect to DMI and fiber digestion, we hypothesize that the 2 diets had different retention times, related to their physical form. A complete-feed pellet diet formulated to provide a sufficient level of NDF from forages could be fed to growing ruminants without apparent negative effects on rumen health and animal productivity, at least for a short period. More research over a longer growing period is needed before recommending this feeding strategy for growing heifers. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of conjugated linoleic acid supplementation and feeding level on dairy performance, milk fatty acid composition, and body fat changes in mid-lactation goats.

PubMed

Ghazal, S; Berthelot, V; Friggens, N C; Schmidely, P

2014-11-01

The objective of this trial was to study the interaction between the supplementation of lipid-encapsulated conjugated linoleic acid (CLA; 4.5 g of cis-9,trans-11 C18:2 and 4.5 g of trans-10,cis-12 C18:2) and feeding level to test if milk performance or milk fatty acid (FA) profile are affected by the interaction between CLA and feeding level. Twenty-four dairy goats were used in an 8-wk trial with a 3-wk adaptation to the experimental ration that contained corn silage, beet pulp, barley, and a commercial concentrate. During the third week, goats were assigned into blocks of 2 goats according to their dry matter intake (DMI), raw milk yield, and fat yield. Each block was randomly allocated to control (45 g of Ca salt of palm oil/d) or CLA treatment. Within each block, one goat was fed to cover 100% (FL100) of the calculated energy requirements and the other was fed 85% of the DMI of the first goat (FL85). Individual milk production and composition were recorded weekly, and milk FA composition was analyzed in wk 3, 5, and 7. Conjugated linoleic acid supplementation reduced milk fat content and fat yield by 17 and 19%, respectively, independent of the feeding level. It reduced both the secretion of milk FA synthesized de novo, and those taken up from the blood. No interaction between CLA and feeding level was observed on milk secretion of any group of FA. The CLA supplementation had no effect on DMI, milk yield, protein, and lactose yields but it improved calculated net energy for lactation balance. Goats fed the FL100 × CLA diet tended to have the highest DMI and protein yield. The interaction between CLA and feeding level was not significant for any other variables. Compared with the goats fed FL100, those fed FL85 had lower DMI, lower net energy for lactation balance, and lower digestible protein in the intestine balance. The body weight; milk yield; milk fat, protein, and lactose yields; and fat, protein, lactose, and urea contents in milk were not affected by feeding level. In conclusion, reduction in energy spared via fat yield reduction after CLA supplementation was not partitioned toward milk lactose or protein in goats at a low feeding level, possibly because of a simultaneous shortage of energy and amino acids. In goats on the high feeding level, energy spared tended to be partitioned toward milk protein yield, and at the same time to the prevention of excessive lipid mobilization. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The genetic and biological basis of feed efficiency in mid-lactation Holstein dairy cows.

PubMed

Hardie, L C; VandeHaar, M J; Tempelman, R J; Weigel, K A; Armentano, L E; Wiggans, G R; Veerkamp, R F; de Haas, Y; Coffey, M P; Connor, E E; Hanigan, M D; Staples, C; Wang, Z; Dekkers, J C M; Spurlock, D M

2017-11-01

The objective of this study was to identify genomic regions and candidate genes associated with feed efficiency in lactating Holstein cows. In total, 4,916 cows with actual or imputed genotypes for 60,671 single nucleotide polymorphisms having individual feed intake, milk yield, milk composition, and body weight records were used in this study. Cows were from research herds located in the United States, Canada, the Netherlands, and the United Kingdom. Feed efficiency, defined as residual feed intake (RFI), was calculated within location as the residual of the regression of dry matter intake (DMI) on milk energy (MilkE), metabolic body weight (MBW), change in body weight, and systematic effects. For RFI, DMI, MilkE, and MBW, bivariate analyses were performed considering each trait as a separate trait within parity group to estimate variance components and genetic correlations between them. Animal relationships were established using a genomic relationship matrix. Genome-wide association studies were performed separately by parity group for RFI, DMI, MilkE, and MBW using the Bayes B method with a prior assumption that 1% of single nucleotide polymorphisms have a nonzero effect. One-megabase windows with greatest percentage of the total genetic variation explained by the markers (TGVM) were identified, and adjacent windows with large proportion of the TGVM were combined and reanalyzed. Heritability estimates for RFI were 0.14 (±0.03; ±SE) in primiparous cows and 0.13 (±0.03) in multiparous cows. Genetic correlations between primiparous and multiparous cows were 0.76 for RFI, 0.78 for DMI, 0.92 for MBW, and 0.61 for MilkE. No single 1-Mb window explained a significant proportion of the TGVM for RFI; however, after combining windows, significance was met on Bos taurus autosome 27 in primiparous cows, and nearly reached on Bos taurus autosome 4 in multiparous cows. Among other genes, these regions contain β-3 adrenergic receptor and the physiological candidate gene, leptin, respectively. Between the 2 parity groups, 3 of the 10 windows with the largest effects on DMI neighbored windows affecting RFI, but were not in the top 10 regions for MilkE or MBW. This result suggests a genetic basis for feed intake that is unrelated to energy consumption required for milk production or expected maintenance as determined by MBW. In conclusion, feed efficiency measured as RFI is a polygenic trait exhibiting a dynamic genetic basis and genetic variation distinct from that underlying expected maintenance requirements and milk energy output. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Some considerations for a method that simultaneously measures the temperature and emissivity of a metal in a high temperature furnace

NASA Astrophysics Data System (ADS)

Iuchi, Tohru; Furukawa, Tohru

2004-12-01

This article describes some considerations for designing a practical radiation thermometry system for a glossy metal moving through a high temperature furnace, such as a continuous annealing furnace. In order to accomplish this task, two problems must be solved. The emissivity compensation of an object must be calculated and the furnace's background radiation noise must be eliminated. The authors have proposed a method that uses the radiance's polarized directional properties to simultaneously measure the emissivity and temperature to solve the first problem and a technique using a pseudo-blackbody installed in the furnace to solve the second problem. During heating, there is a one-to-one correspondence between the emissivity and the ratio of p- and s-polarized radiances for metals. This characteristic has successfully led to the development of a method for simultaneously measuring the emissivity and temperature of metals regardless of a potential large change in emissivity. Introducing a pseudo-blackbody radiator into a furnace removes the background radiation noise. Moreover, the blackbody radiator supplies a constant reference radiance. This reference plays an important role in maintaining the principle of emissivity-compensated radiation thermometry inside the furnace. Experimental results have simultaneously measured the emissivity and temperature of stainless steel at 1300 K with errors of 12% and 0.96%, respectively. These values were attained even though the s-polarized emissivities change from 0.25 to 0.75 at a wavelength of 0.9 μm. These errors can be achieved by designing the apparatus to have a solid angle, the aperture of the pseudo-blackbody subtended by a measuring point of the specimen, of more than 0.02π steradians. The accuracy of this method is heavily dependent upon the specimen's surface roughness. The maximum surface roughness that allows for the successful utilization of this method is Ra=0.12 μm.

Late Quaternary faulting along the Death Valley-Furnace Creek fault system, California and Nevada

USGS Publications Warehouse

Brogan, George E.; Kellogg, Karl; Slemmons, D. Burton; Terhune, Christina L.

1991-01-01

The Death Valley-Furnace Creek fault system, in California and Nevada, has a variety of impressive late Quaternary neotectonic features that record a long history of recurrent earthquake-induced faulting. Although no neotectonic features of unequivocal historical age are known, paleoseismic features from multiple late Quaternary events of surface faulting are well developed throughout the length of the system. Comparison of scarp heights to amount of horizontal offset of stream channels and the relationships of both scarps and channels to the ages of different geomorphic surfaces demonstrate that Quaternary faulting along the northwest-trending Furnace Creek fault zone is predominantly right lateral, whereas that along the north-trending Death Valley fault zone is predominantly normal. These observations are compatible with tectonic models of Death Valley as a northwest-trending pull-apart basin. The largest late Quaternary scarps along the Furnace Creek fault zone, with vertical separation of late Pleistocene surfaces of as much as 64 m (meters), are in Fish Lake Valley. Despite the predominance of normal faulting along the Death Valley fault zone, vertical offset of late Pleistocene surfaces along the Death Valley fault zone apparently does not exceed about 15 m. Evidence for four to six separate late Holocene faulting events along the Furnace Creek fault zone and three or more late Holocene events along the Death Valley fault zone are indicated by rupturing of Q1B (about 200-2,000 years old) geomorphic surfaces. Probably the youngest neotectonic feature observed along the Death Valley-Furnace Creek fault system, possibly historic in age, is vegetation lineaments in southernmost Fish Lake Valley. Near-historic faulting in Death Valley, within several kilometers south of Furnace Creek Ranch, is represented by (1) a 2,000-year-old lake shoreline that is cut by sinuous scarps, and (2) a system of young scarps with free-faceted faces (representing several faulting events) that cuts Q1B surfaces.

Furnace Cyclic Oxidation Behavior of Multicomponent Low Conductivity Thermal Barrier Coatings

NASA Astrophysics Data System (ADS)

Zhu, Dongming; Nesbitt, James A.; Barrett, Charles A.; McCue, Terry R.; Miller, Robert A.

2004-03-01

Ceramic thermal barrier coatings (TBCs) will play an increasingly important role in advanced gas turbine engines due to their ability to further increase engine operating temperatures and reduce cooling, thus helping achieve future engine low emission, high efficiency, and improved reliability goals. Advanced multicomponent zirconia (ZrO2)-based TBCs are being developed using an oxide defect clustering design approach to achieve the required coating low thermal conductivity and high-temperature stability. Although the new composition coatings were not yet optimized for cyclic durability, an initial durability screening of the candidate coating materials was conducted using conventional furnace cyclic oxidation tests. In this paper, furnace cyclic oxidation behavior of plasma-sprayed ZrO2-based defect cluster TBCs was investigated at 1163°C using 45 min hot-time cycles. The ceramic coating failure mechanisms were studied using scanning electron microscopy (SEM) combined with x-ray diffraction (XRD) phase analysis after the furnace tests. The coating cyclic lifetime is also discussed in relation to coating processing, phase structures, dopant concentration, and other thermo-physical properties.

Furnace Cyclic Oxidation Behavior of Multi-Component Low Conductivity Thermal Barrier Coatings

NASA Technical Reports Server (NTRS)

Zhu, Dong-Ming; Nesbitt, James A.; Barrett, Charles A.; McCue, Terry R.; Miller, Robert A.

2004-01-01

Ceramic thermal barrier coatings will play an increasingly important role in advanced gas turbine engines because of their ability to further increase engine operating temperatures and reduce cooling, thus helping achieve future engine low emission, high efficiency and improved reliability goals. Advanced multi-component zirconia-based thermal barrier coatings are being developed using an oxide defect clustering design approach to achieve the required coating low thermal conductivity and high temperature stability. Although the new composition coatings were not yet optimized for cyclic durability, an initial durability screening of the candidate coating materials was conducted using conventional furnace cyclic oxidation tests. In this paper, furnace cyclic oxidation behavior of plasma-sprayed zirconia-based defect cluster thermal barrier coatings was investigated at 1163 C using 45 min hot cycles. The ceramic coating failure mechanisms were studied using scanning electron microscopy (SEM) combined with X-ray diffraction (XRD) phase analysis after the furnace tests. The coating cyclic lifetime is also discussed in relation to coating processing, phase structures, dopant concentration, and other thermo-physical properties.

QMI: Rising to the Space Station Design Challenge

NASA Astrophysics Data System (ADS)

Carswell, W. E.; Farmer, J.; Coppens, C.; Breeding, S.; Rose, F.

2002-01-01

The Quench Module Insert (QMI) materials processing furnace is being designed to operate for 8000 hours over four years on the International Space Station as part of the first Materials Science Research Rack of the Materials Science Research Facility. The Bridgman-type furnace is being built for the directional solidification processing of metals and alloys in the microgravity environment of space. Most notably it will be used for processing aluminum and related alloys. Designing for the space station environment presents intriguing design challenges in the form of a ten-year life requirement coupled with both limited opportunities for maintenance and resource constraints in the form of limited power and space. The long life requirement has driven the design of several features in the furnace, including the design of the heater core, the selection and placement of the thermocouples, overall performance monitoring, and the design of the chill block. The power and space limitations have been addressed through a compact furnace design using efficient vacuum insulation. Details on these design features, as well as development test performance results to date, are presented.

QMI: Rising to the Space Station Design Challenge

NASA Technical Reports Server (NTRS)

Carswell, W. E.; Farmer, J.; Coppens, C.; Breeding, S.; Rose, F.; Curreri, Peter A. (Technical Monitor)

2002-01-01

The Quench Module Insert (QMI) materials processing furnace is being designed to operate for 8000 hours over four years on the International Space Station (ISS) as part of the first Materials Science Research Rack (MSRR-1) of the Materials Science Research Facility (MSRF). The Bridgman-type furnace is being built for the directional solidification processing of metals and alloys in the microgravity environment of space. Most notably it will be used for processing aluminum and related alloys. Designing for the space station environment presents intriguing design challenges in the form of a ten-year life requirement coupled with both limited opportunities for maintenance and resource constraints in the form of limited power and space. The long life requirement has driven the design of several features in the furnace, including the design of the heater core, the selection and placement of the thermocouples, overall performance monitoring, and the design of the chill block. The power and space limitations have been addressed through a compact furnace design using efficient vacuum insulation. Details on these design features, as well as development test performance results to date, are presented.

A technique for measuring the heat transfer coefficient inside a Bridgman furnace

NASA Technical Reports Server (NTRS)

Rosch, W.; Jesser, W.; Debnam, W.; Fripp, A.; Woodell, G.; Pendergrass, T. K.

1993-01-01

Knowledge of the amount of heat that is conducted, advected and radiated between an ampoule and the furnace is important for understanding vertical Bridgman crystal growth. This heat transfer depends on the temperature, emissivities and geometries of both the furnace and ampoule, as well as the choice of ambient gas inside the furnace. This paper presents a method which directly measures this heat transfer without the need to know any physical properties of the furnace, the ampoule, or the gaseous environment. Data are given for one specific furnace in which this method was used.

Computational Fluid Dynamics (CFD) Investigation of Submerged Combustion Behavior in a Tuyere Blown Slag-fuming Furnace

NASA Astrophysics Data System (ADS)

Huda, Nazmul; Naser, Jamal; Brooks, G. A.; Reuter, M. A.; Matusewicz, R. W.

2012-10-01

A thin-slice computational fluid dynamics (CFD) model of a conventional tuyere blown slag-fuming furnace has been developed in Eulerian multiphase flow approach by employing a three-dimensional (3-D) hybrid unstructured orthographic grid system. The model considers a thin slice of the conventional tuyere blown slag-fuming furnace to investigate details of fluid flow, submerged coal combustion dynamics, coal use behavior, jet penetration behavior, bath interaction conditions, and generation of turbulence in the bath. The model was developed by coupling the CFD with the kinetics equations developed by Richards et al. for a zinc-fuming furnace. The model integrates submerged coal combustion at the tuyere tip and chemical reactions with the heat, mass, and momentum interfacial interaction between the phases present in the system. A commercial CFD package AVL Fire 2009.2 (AVL, Graz, Austria) coupled with several user-defined subroutines in FORTRAN programming language were used to develop the model. The model predicted the velocity, temperature field of the molten slag bath, generated turbulence and vortex, and coal use behavior from the slag bath. The tuyere jet penetration length ( l P) was compared with the equation provided by Hoefele and Brimacombe from isothermal experimental work ( {{l_{{P}} }/{d_{o }} = 10.7( {N^' }_{Fr} } )^{0.46} ( {ρ_{{g}} /ρl } )^{0.35} } ) and found 2.26 times higher, which can be attributed to coal combustion and gas expansion at a high temperature. The jet expansion angle measured for the slag system studied is 85 deg for the specific inlet conditions during the simulation time studied. The highest coal penetration distance was found to be l/L = 0.2, where l is the distance from the tuyere tip along the center line and L is the total length (2.44 m) of the modeled furnace. The model also predicted that 10 pct of the injected coal bypasses the tuyere gas stream uncombusted and carried to the free surface by the tuyere gas stream, which contributes to zinc oxide reduction near the free surface.

Ultra-High Temperature ContinuousReactors based on Electro-thermal FluidizedBed Concept

DOE PAGES

Fedorov, Sergiy S.; Rohatgi, Upendra Singh; Barsukov, Igor V.; ...

2015-12-08

This paper presents the results of research and development in high-temperature (i.e. 2,000- 3,000ºС) continuous furnaces operating on the principle of electro-thermal fluidized bed for the purification of recycled, finely sized carbon materials. The basis of this fluidized bed furnace is specific electrical resistance and a new correlation has been developed to predict specific electrical resistance for the natural graphite-based precursors entering the fluidized bed reactor This correlation has been validated with the data from a fully functional pilot furnace whose throughput capacity is 10 kg per hour built as part of this work. Data collected in the course ofmore » graphite refining experiments demonstrated that difference between the calculated and measured values of specific electrical resistance of fluidized bed does not exceed 25%. It was concluded that due to chaotic nature of electro-thermal fluidized bed reactors this discrepancy is acceptable. The fluid mechanics of the three types of operating regimes, have been described. The numerical relationships obtained as part of this work allowed proposing an algorithm for selection of technological operational modes with large- scale high-temperature furnaces rated for throughputs of several tons of product per hour. Optimizations proposed now allow producing natural graphite-based end product with the purity level of 99.98+ wt%C which is the key passing criteria for applications in the advanced battery markets.« less

Growth rates and interface shapes in germanium and lead tin telluride observed in-situ, real-time in vertical Bridgman furnaces

NASA Technical Reports Server (NTRS)

Barber, P. G.; Berry, R. F.; Debnam, W. J.; Fripp, A. L.; Woodell, G.; Simchick, R. T.

1995-01-01

Using the advanced technology developed to visualize the melt-solid interface in low Prandtl number materials, crystal growth rates and interface shapes have been measured in germanium and lead tin telluride semiconductors grown in vertical Bridgman furnaces. The experimental importance of using in-situ, real time observations to determine interface shapes, to measure crystal growth rates, and to improve furnace and ampoule designs is demonstrated. The interface shapes observed in-situ, in real-time were verified by quenching and mechanically induced interface demarcation, and they were also confirmed using machined models to ascertain the absence of geometric distortions. Interface shapes depended upon the interface position in the furnace insulation zone, varied with the nature of the crystal being grown, and were dependent on the extent of transition zones at the ends of the ampoule. Actual growth rates varied significantly from the constant translation rate in response to the thermophysical properties of the crystal and its melt and the thermal conditions existing in the furnace at the interface. In the elemental semiconductor germanium the observed rates of crystal growth exceeded the imposed translation rate, but in the compound semiconductor lead tin telluride the observed rates of growth were less than the translation rate. Finally, the extent of ampoule thermal loading influenced the interface positions, the shapes, and the growth rates.

Modelling of nitrogen oxides distribution in the hearth of gas-fired industrial furnace

NASA Astrophysics Data System (ADS)

Zhubrin, S.; Glazov, V.; Guzhov, S.

2017-11-01

A model is proposed for calculating the formation and transportation of nitrogen oxides in the combustion chamber of an industrial furnace heated by gaseous fuels burning. The calculations use a three-dimensional stationary description of turbulent flow and mixing of fuel and oxidizer flows in the presence of heat transfer, mass transfer, and momentum between them transfer. Simulation of the spatial pattern of nitrogen oxides formation in the working space of the furnace is performed in the programming and computing suite SCAN. It is shown that the temperature non-uniformity over the hearth surface is not too pronounced due to the organization of the inclined flow inlet in the direction of the hearth, which is a desirable feature of the furnace operation. The highest concentration of combustion products is observed in the zone of maximum temperatures. In addition, the existence of two zones of the highest generation of oxides has been determined. The first zone is located approximately in the center of the hearth, and the second is located on the far external surface of the furnace. The possibility of using the developed model in the SCAN complex for carrying out parametric studies and engineering calculations, as well as for modification in the direction of adjusting and adapting the model to the regime-constructive features of specific energy technological devices, is noted.

Development of a Self Aligned CMOS Process for Flash Lamp Annealed Polycrystalline Silicon TFTs

NASA Astrophysics Data System (ADS)

Bischoff, Paul

The emerging active matrix liquid crystal (AMLCD) display market requires a high performing semiconductor material to meet rising standards of operation. Currently amorphous silicon (a-Si) dominates the market but it does not have the required mobility for it to be used in AMLCD manufacturing. Other materials have been developed including crystallizing a-Si into poly-silicon. A new approach to crystallization through the use of flash lamp annealing (FLA) decreases manufacturing time and greatly improves carrier mobility. Previous work on FLA silicon for the use in CMOS transistors revealed significant lateral dopant diffusion into the channel greatly increasing the minimum channel length required for a working device. This was further confounded by the gate overlap due to misalignment during lithography patterning steps. Through the use of furnace dopant activation instead of FLA dopant activation and a self aligned gate the minimum size transistor can be greatly reduced. A new lithography mask and process flow were developed for the furnace annealing and self aligned gate. Fabrication of the self aligned devices resulted in oxidation of the Molybdenum self aligned gate. Further development is needed to successfully manufacture these devices. Non-self aligned transistors were made simultaneously with self aligned devices and used the furnace activation. These devices showed an increase in sheet resistance from 250 O to 800 O and lower mobility from 380 to 40.2 V/cm2s. The lower mobility can be contributed to an increase in implanted trap density indicating furnace annealing is an inferior activation method over FLA. The minimum transistor size however was reduced from 20 to 5 mum. With improvements in the self aligned process high performing small devices can be manufactured.

Associations between the degree of early lactation inflammation and performance, metabolism, and immune function in dairy cows.

PubMed

McCarthy, M M; Yasui, T; Felippe, M J B; Overton, T R

2016-01-01

The objective of the current study was to determine associations between the severity of systemic inflammation during the early postpartum period and performance, energy metabolism, and immune function in dairy cows. Cows were assigned to categorical quartiles (Q; Q1=0.18-0.59, Q2=0.60-1.14, Q3=1.15-2.05, and Q4=2.06-2.50 g of haptoglobin/L) based on the highest plasma haptoglobin (Hp) concentration measured during wk 1 postpartum. Although cows were assigned to different categories of inflammation during the postpartum period, we detected a quadratic relationship of inflammation on prepartum dry matter intake (DMI) and body weight (BW) such that cows in Q2 had lower prepartum DMI and cows in Q2 and Q3 had lower prepartum BW compared with cows in the other quartiles. We also detected a quadratic association of inflammation with postpartum DMI and BW such that cows in Q2 and Q3 also had generally lower postpartum DMI and BW compared with cows in Q1. There was a tendency for a Q × time interaction for milk yield and Q × time interactions for 3.5% fat-corrected milk and energy-corrected milk yields; quadratic relationships suggested decreased milk yield for Q2 and Q3 cows. We also found Q × parity and Q × time interactions for plasma glucose and insulin concentrations, suggesting alterations with differing degrees of inflammation. There was also a Q × time interaction for plasma nonesterified fatty acids concentration. In addition, alterations in liver triglyceride and glycogen contents for cows with inflammation as well as alterations in [1-(14)C]propionate oxidation in vitro were observed. Although we observed limited effects of inflammation on neutrophil and monocyte phagocytosis at d 7 postpartum, inflammation appeared to alter neutrophil and monocyte oxidative burst. Overall, cows with any degree of elevated haptoglobin in the first week after calving had alterations in both pre- and postpartum intake and postpartum metabolism. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Performance, carcass characteristics, and ruminal pH of Nellore and Angus young bulls fed a whole shelled corn diet.

PubMed

Carvalho, J R R; Chizzotti, M L; Schoonmaker, J P; Teixeira, P D; Lopes, R C; Oliveira, C V R; Ladeira, M M

2016-06-01

The objectives of this study were to test the interaction of breed (Nellore or Angus) and diet (whole shelled corn [WSC] or ground corn [GC] with silage) on growth performance, carcass characteristics, and ruminal pH of young bulls. Thirty-six bulls (18 Nellore and 18 Angus) with the range in age of 18 to 22 mo and BW of 381 ± 12 kg were used in a completely randomized design experiment with a 2 × 2 factorial arrangement of treatments (2 breeds and 2 diets). Experimental diets (DM basis) included 1) a GC diet containing 30% corn silage and 70% GC- and soybean meal-based concentrate and 2) a WSC diet containing 85% WSC and 15% of a soybean meal- and mineral-based pelleted supplement. An additional 8 bulls were slaughtered at the beginning of the experimental period for determination of initial carcass weight. The treatments were Nellore fed the GC diet, Nellore fed the WSC diet, Angus fed the GC diet, and Angus fed the WSC diet. Greater DMI ( < 0.01), ADG ( < 0.01), and G:F ( < 0.01) were observed in Angus bulls compared with Nellore bulls, regardless of diet. Lower average ruminal pH ( = 0.04), maximum ruminal pH (P = 0.02), and DMI ( < 0.01) were observed in bulls fed the WSC diet than in those fed the GC diet. In addition, bulls fed the WSC diet had greater G:F ( < 0.01). The WSC diet led to greater variation in DMI compared with the GC diet ( < 0.01). Omasum and large intestine percentage was affected by diets only in the Angus breed ( < 0.02) and were greater when bulls were fed the GC diet. The WSC diet without forage may be useful for feedlots because this diet promoted greater G:F than the GC diet, regardless of breed. However, special care must be exercised in feed management during adaptation and throughout the feeding of Nellore animals to avoid digestive disorders and fluctuations in DMI.

Effects of dietary forage-to-concentrate ratio on nutrient digestibility and enteric methane production in growing goats (Capra hircus hircus) and Sika deer (Cervus nippon hortulorum).

PubMed

Na, Youngjun; Li, Dong Hua; Lee, Sang Rak

2017-07-01

Two experiments were conducted to determine the effects of forage-to-concentrate (F:C) ratio on the nutrient digestibility and enteric methane (CH 4 ) emission in growing goats and Sika deer. Three male growing goats (body weight [BW] = 19.0±0.7 kg) and three male growing deer (BW = 19.3±1.2 kg) were respectively allotted to a 3×3 Latin square design with an adaptation period of 7 d and a data collection period of 3 d. Respiration-metabolism chambers were used for measuring the enteric CH 4 emission. Treatments of low (25:75), moderate (50:50), and high (73:27) F:C ratios were given to both goats and Sika deer. Dry matter (DM) and organic matter (OM) digestibility decreased linearly with increasing F:C ratio in both goats and Sika deer. In both goats and Sika deer, the CH 4 emissions expressed as g/d, g/kg BW 0.75 , % of gross energy intake, g/kg DM intake (DMI), and g/kg OM intake (OMI) decreased linearly as the F:C ratio increased, however, the CH 4 emissions expressed as g/kg digested DMI and OMI were not affected by the F:C ratio. Eight equations were derived for predicting the enteric CH 4 emission from goats and Sika deer. For goat, equation 1 was found to be of the highest accuracy: CH 4 (g/d) = 3.36+4.71×DMI (kg/d)-0.0036×neutral detergent fiber concentrate (NDFC, g/kg)+0.01563×dry matter digestibility (DMD, g/kg)-0.0108×neutral detergent fiber digestibility (NDFD, g/kg). For Sika deer, equation 5 was found to be of the highest accuracy: CH 4 (g/d) = 66.3+27.7×DMI (kg/d)-5.91×NDFC (g/kg)-7.11× DMD (g/kg)+0.0809×NDFD (g/kg). Digested nutrient intake could be considered when determining the CH 4 generation factor in goats and Sika deer. Finally, the enteric CH 4 prediction model for goats and Sika deer were estimated.

Effect of substitution of concentrate mix with Sesbania sesban on feed intake, digestibility, body weight change, and carcass parameters of Arsi-Bale sheep fed a basal diet of native grass hay.

PubMed

Bekele, Wondwosen; Melaku, Solomon; Mekasha, Yoseph

2013-11-01

An experiment was conducted to assess the effect of substitution of concentrate mix with Sesbania sesban on feed intake, digestibility, average daily gain (ADG), and carcass parameters of Arsi-Bale sheep. The experiment employed 25 male sheep with mean (±standard error) initial body live weight (BLW) of 19.1 ± 0.09 kg. The experiment consisted of 7 days of digestibility and 90 days of feeding trials followed by carcass evaluation. The experiment employed a randomized complete block design with five treatments and five blocks. Treatments comprised of grass hay alone fed ad libitum (GHA; control), GHA + 100 % concentrate mix (CM) consisting of wheat bran and noug seed cake at a ratio of 2:1 (0 S. sesban), GHA + 67 % CM + 33 % S. sesban (33 S. sesban), GHA + 33 % CM + 67 % S. sesban (67 S. sesban), and GHA + 100 % S. sesban (100 S. sesban). Total dry matter intake (DMI) was higher (p < 0.001) for sheep in 0 S. sesban-100 S. sesban (800-821 g/day) compared to sheep in control (611 g/day). However, the effect of S. sesban inclusion (0 S. sesban-100 S. sesban) on total DMI was quadratic, and DMI declined after 67 S. sesban. Digestibility of DM, organic matter (p < 0.01), and crude protein were higher (p < 0.001) in supplemented group compared to the control. ADG, feed conversion efficiency (ADG/DMI), slaughter BLW, hot carcass weight, and total edible offals were higher (p < 0.05-0.001) for sheep in 0 S. sesban-100 S. sesban than those in control. Increased level of S. sesban inclusion, in general, reduced growth and carcass parameters in this study. However, there was no difference between 0 S. sesban and 33 S. sesban in most parameters studied. Thus, it can be concluded that S. sesban could substitute a concentrate when it accounted for up to 33 % of the mix.

Effects of feeding a spray-dried multivalent polyclonal antibody preparation on feedlot performance, feeding behavior, carcass characteristics, rumenitis, and blood gas profile of Brangus and Nellore yearling bulls.

PubMed

Millen, D D; Pacheco, R D L; DiLorenzo, N; Martins, C L; Marino, C T; Bastos, J P S T; Mariani, T M; Barducci, R S; Sarti, L M N; DiCostanzo, A; Rodrigues, P H M; Arrigoni, M D B

2015-09-01

The objective of this study was to evaluate the effects of replacing monensin (MON) with a spray-dried multivalent polyclonal antibody preparation (PAP) against several ruminal microorganisms on feedlot performance, carcass characteristics, feeding behavior, blood gas profile, and the rumenitis incidence of Brangus and Nellore yearling bulls. The study was designed as a completely randomized design with a 2 × 2 factorial arrangement, replicated 6 times (4 bulls per pen and a total of 24 pens), in which bulls ( = 48) of each biotype were fed diets containing either MON fed at 300 mg/d or PAP fed at 3 g/d. No significant feed additive main effects were observed for ADG ( = 0.27), G:F ( = 0.28), HCW ( = 0.99), or dressing percentage ( = 0.80). However, bulls receiving PAP had greater DMI ( = 0.02) and larger ( = 0.02) final LM area as well as greater ( < 0.01) blood concentrations of bicarbonate and base excess in the extracellular fluid than bulls receiving MON. Brangus bulls had greater ( < 0.01) ADG and DMI expressed in kilograms, final BW, heavier HCW, and larger initial and final LM area than Nellore bulls. However, Nellore bulls had greater daily DMI fluctuation ( < 0.01), expressed as a percentage, and greater incidence of rumenitis ( = 0.05) than Brangus bulls. In addition, Brangus bulls had greater ( < 0.01) DMI per meal and also presented lower ( < 0.01) DM and NDF rumination rates when compared with Nellore bulls. Significant interactions ( < 0.05) between biotype and feed additive were observed for SFA, unsaturated fatty acids (UFA), MUFA, and PUFA concentrations in adipose tissues. When Nellore bulls were fed PAP, fat had greater ( < 0.05) SFA and PUFA contents but less ( < 0.01) UFA and MUFA than Nellore bulls receiving MON. For Brangus bulls, MON led to greater ( < 0.05) SFA and PUFA and less ( < 0.05) UFA and MUFA than Brangus bulls fed PAP. Feeding a spray-dried PAP led to similar feedlot performance compared with that when feeding MON. Spray-dried PAP might provide a new technology alternative to ionophores.

Reproductive parameters of tropical lesser noddies respond to local variations in oceanographic conditions and weather

NASA Astrophysics Data System (ADS)

Monticelli, David; Ramos, Jaime A.; Catry, Teresa; Pedro, Patricia; Paiva, Vitor H.

2014-02-01

Most attempts to link seabirds and climate/oceanographic effects have concerned the Atlantic and Pacific Oceans with comparatively few studies in the tropical Indian Ocean. This paper examines the reproductive response of the lesser noddy Anous tenuirostris to temporal fluctuations in oceanographic and climatic conditions using 8 years of monitoring data from Aride Island (Seychelles), tropical Western Indian Ocean. We tested the hypothesis that breeding parameters (mean hatching date, mean egg size, hatching and fledging successes) and chick growth are influenced by local, seasonal oceanographic conditions as expressed by ocean primary productivity (surface chlorophyll-a concentrations; CC), sea surface temperature (SST) and wind speed. We also examined the relationship between lesser noddy breeding parameters and climate conditions recorded at the basin-wide scale of the Indian Ocean (Indian Ocean Dipole Mode Index, DMI). Our findings suggest that birds had a tendency to lay slightly larger eggs during breeding seasons (years) with higher CC during April-June (pre-laying, laying and incubation periods). Hatching date was positively related to SST in April-June, with the regression parameters suggesting that each 0.5 °C increase in SST meant a delay of approx.10 days in hatching date. A negative linear relationship was also apparent between hatching success and SST in June-August (hatching and chick-rearing periods), while the quadratic regression models detected a significant effect of wind speed in June-August on fledging success. Body mass increments of growing chicks averaged over 7-day periods were positively related with (2-week) lagged CC values and negatively related with (2-week) lagged SST values. No significant relationship between DMI and lesser noddy breeding parameters was found, but DMI indices were strongly correlated with local SST. Altogether, our results indicate that the reproduction of this top marine predator is dictated by fluctuations in local environmental conditions around the colony, while the effects of large-scale oceanographic processes (DMI) on our study population might be mediated by an effect on local SST.

Effect of furnace type and ceramming heat treatment conditions on the biaxial flexural strength of a canasite glass-ceramic.

PubMed

Johnson, A; Shareef, M Y; van Noort, R; Walsh, J M

2000-07-01

To assess the effect of different heat treatment conditions when using two different furnace types on the biaxial flexural strength (BFS) of a fluorcanasite castable glass-ceramic. Two furnace types, one a programmable furnace (PF), the other a dental laboratory burnout furnace (DLF), were used with various ceramming times to determine their effect on the BFS of a fluorcanasite castable glass-ceramic. The glass-ceramic material was cast to produce discs of 12 mm diameter and 2 mm thickness using the lost wax casting process (n = 80). After casting, both furnace types were used to ceram the discs. Half the discs were not de-vested from the casting ring before ceramming but cerammed in situ (DLF) and half were de-vested before ceramming (PF). All the discs were given a nucleation heat treatment at 520 degrees C for 1 h and then cerammed at 860 degrees C using four heat soak times (0.5, 1, 2 and 3 h). The DLF furnace had a rate of climb of 13 degrees C/min and the PF furnace had a rate of climb of 5 degrees C/min to 520 degrees C and 3 degrees C/min to 860 degrees C. After ceramming the discs were de-vested and the BFS determined using a Lloyd 2000R tester. The maximum BFS values seen for both furnace types were almost identical (280 MPa), but were achieved at different heat soak times (1 h DLF, and 2 h PF). The only significant differences in BFS values for the two furnaces were between the 0.5 and 2 h heat soak times (p < or = 0.05). Individual differences were seen between results obtained from each furnace type/heat soak times evaluated (p < or = 0.05). Already available dental laboratory burnout furnaces can be used to ceram fluorcanasite glass-ceramic castings to the same BFS values as more expensive and slower specialist programmable furnaces.

40 CFR 424.50 - Applicability; description of the other calcium carbide furnaces subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... calcium carbide furnaces subcategory. 424.50 Section 424.50 Protection of Environment ENVIRONMENTAL... CATEGORY Other Calcium Carbide Furnaces Subcategory § 424.50 Applicability; description of the other calcium carbide furnaces subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 424.50 - Applicability; description of the other calcium carbide furnaces subcategory.

Code of Federal Regulations, 2011 CFR

2011-07-01

... calcium carbide furnaces subcategory. 424.50 Section 424.50 Protection of Environment ENVIRONMENTAL... CATEGORY Other Calcium Carbide Furnaces Subcategory § 424.50 Applicability; description of the other calcium carbide furnaces subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 424.50 - Applicability; description of the other calcium carbide furnaces subcategory.

Code of Federal Regulations, 2014 CFR

2014-07-01

... calcium carbide furnaces subcategory. 424.50 Section 424.50 Protection of Environment ENVIRONMENTAL... CATEGORY Other Calcium Carbide Furnaces Subcategory § 424.50 Applicability; description of the other calcium carbide furnaces subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 424.50 - Applicability; description of the other calcium carbide furnaces subcategory.

Code of Federal Regulations, 2013 CFR

2013-07-01

... calcium carbide furnaces subcategory. 424.50 Section 424.50 Protection of Environment ENVIRONMENTAL... CATEGORY Other Calcium Carbide Furnaces Subcategory § 424.50 Applicability; description of the other calcium carbide furnaces subcategory. The provisions of this subpart are applicable to discharges...

An update on blast furnace granular coal injection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, D.G.; Strayer, T.J.; Bouman, R.W.

1997-12-31

A blast furnace coal injection system has been constructed and is being used on the furnace at the Burns Harbor Division of Bethlehem Steel. The injection system was designed to deliver both granular (coarse) and pulverized (fine) coal. Construction was completed on schedule in early 1995. Coal injection rates on the two Burns Harbor furnaces were increased throughout 1995 and was over 200 lbs/ton on C furnace in September. The injection rate on C furnace reached 270 lbs/ton by mid-1996. A comparison of high volatile and low volatile coals as injectants shows that low volatile coal replaces more coke andmore » results in a better blast furnace operation. The replacement ratio with low volatile coal is 0.96 lbs coke per pound of coal. A major conclusion of the work to date is that granular coal injection performs very well in large blast furnaces. Future testing will include a processed sub-bituminous coal, a high ash coal and a direct comparison of granular versus pulverized coal injection.« less

Status and Evaluation of Microwave Furnace Capabilities at NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Lizcano, Maricela; Mackey, Jonathan A.

2014-01-01

The microwave (MW) furnace is a HY-Tech Microwave Systems, 2 kW 2.45 GHz Single Mode Microwave Applicator operating in continuous wave (CW) with variable power. It is located in Cleveland, Ohio at NASA Glenn Research Center. Until recently, the furnace capabilities had not been fully realized due to unknown failure that subsequently damaged critical furnace components. Although the causes of the problems were unknown, an assessment of the furnace itself indicated operational failure may have been partially caused by power quality. This report summarizes the status of the MW furnace and evaluates its capabilities in materials processing.

Heat treatment furnace

DOEpatents

Seals, Roland D; Parrott, Jeffrey G; DeMint, Paul D; Finney, Kevin R; Blue, Charles T

2014-10-21

A furnace heats through both infrared radiation and convective air utilizing an infrared/purge gas design that enables improved temperature control to enable more uniform treatment of workpieces. The furnace utilizes lamps, the electrical end connections of which are located in an enclosure outside the furnace chamber, with the lamps extending into the furnace chamber through openings in the wall of the chamber. The enclosure is purged with gas, which gas flows from the enclosure into the furnace chamber via the openings in the wall of the chamber so that the gas flows above and around the lamps and is heated to form a convective mechanism in heating parts.

Molten metal injector system and method

DOEpatents

Meyer, Thomas N.; Kinosz, Michael J.; Bigler, Nicolas; Arnaud, Guy

2003-04-01

Disclosed is a molten metal injector system including a holder furnace, a casting mold supported above the holder furnace, and a molten metal injector supported from a bottom side of the mold. The holder furnace contains a supply of molten metal having a metal oxide film surface. The bottom side of the mold faces the holder furnace. The mold defines a mold cavity for receiving the molten metal from the holder furnace. The injector projects into the holder furnace and is in fluid communication with the mold cavity. The injector includes a piston positioned within a piston cavity defined by a cylinder for pumping the molten metal upward from the holder furnace and injecting the molten metal into the mold cavity under pressure. The piston and cylinder are at least partially submerged in the molten metal when the holder furnace contains the molten metal. The cylinder further includes a molten metal intake for receiving the molten metal into the piston cavity. The molten metal intake is located below the metal oxide film surface of the molten metal when the holder furnace contains the molten metal. A method of injecting molten metal into a mold cavity of a casting mold is also disclosed.

40 CFR 63.1503 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... is contained. Group 1 furnace means a furnace of any design that melts, holds, or processes aluminum..., or processes clean charge with reactive fluxing. Group 2 furnace means a furnace of any design that...-on air pollution control device means equipment installed on a process vent that reduces the quantity...

40 CFR 63.1503 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... is contained. Group 1 furnace means a furnace of any design that melts, holds, or processes aluminum..., or processes clean charge with reactive fluxing. Group 2 furnace means a furnace of any design that...-on air pollution control device means equipment installed on a process vent that reduces the quantity...

57. GENERAL VIEW OF FURNACES No. 3 AND No. 4 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

57. GENERAL VIEW OF FURNACES No. 3 AND No. 4 TO THE LEFT OF THE FURNACES IS THE ORE BRIDGE, THE TURBO-GENERATOR BUILDING, AND THE WATER FILTER TANKS. - U.S. Steel Homestead Works, Blast Furnace Plant, Along Monongahela River, Homestead, Allegheny County, PA

56. GENERAL VIEW OF FURNACES No. 3 AND No. 4 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

56. GENERAL VIEW OF FURNACES No. 3 AND No. 4 TO THE LEFT OF THE FURNACES IS THE ORE BRIDGE, THE TURBO-GENERATOR BUILDING, AND THE WATER FILTER TANKS. - U.S. Steel Homestead Works, Blast Furnace Plant, Along Monongahela River, Homestead, Allegheny County, PA

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

40 CFR 63.544 - Standards for process fugitive sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Smelting furnace and dryer charging hoppers, chutes, and skip hoists; (2) Smelting furnace lead taps, and molds during tapping; (3) Smelting furnace slag taps, and molds during tapping; (4) Refining kettles; (5) Dryer transition pieces; and (6) Agglomerating furnace product taps. (b) Process fugitive emission...

40 CFR 424.50 - Applicability; description of the other calcium carbide furnaces subcategory.

Code of Federal Regulations, 2012 CFR

2012-07-01

... other calcium carbide furnaces subcategory. 424.50 Section 424.50 Protection of Environment... SOURCE CATEGORY Other Calcium Carbide Furnaces Subcategory § 424.50 Applicability; description of the other calcium carbide furnaces subcategory. The provisions of this subpart are applicable to discharges...

40 CFR 63.1503 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... is contained. Group 1 furnace means a furnace of any design that melts, holds, or processes aluminum..., or processes clean charge with reactive fluxing. Group 2 furnace means a furnace of any design that... section as follows: Add-on air pollution control device means equipment installed on a process vent that...

40 CFR 63.1503 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... is contained. Group 1 furnace means a furnace of any design that melts, holds, or processes aluminum..., or processes clean charge with reactive fluxing. Group 2 furnace means a furnace of any design that... section as follows: Add-on air pollution control device means equipment installed on a process vent that...

40 CFR 63.1503 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... is contained. Group 1 furnace means a furnace of any design that melts, holds, or processes aluminum..., or processes clean charge with reactive fluxing. Group 2 furnace means a furnace of any design that... section as follows: Add-on air pollution control device means equipment installed on a process vent that...

FURNACE NO. 1, THE ORIGINAL FURNACE OF THE GLASS FACTORY; ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

FURNACE NO. 1, THE ORIGINAL FURNACE OF THE GLASS FACTORY; TO THE LEFT IS A GLORY HOLE, POSSIBLY DATING FROM THE NINETEENTH CENTURY; THE SQUARE-SHAPED GLORY HOLE TO THE RIGHT PROBABLY DATES FROM THE 1950S. - Westmoreland Glass Company, Seventh & Kier Streets, Grapeville, Westmoreland County, PA

6. GENERAL VIEW OF FURNACES No. 3 AND No. 4 ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. GENERAL VIEW OF FURNACES No. 3 AND No. 4 TO THE LEFT OF THE FURNACES ARE THE ORE BRIDGE, THE TURBO-GENERATOR BUILDING, AND THE WATER FILTER TANKS. Jet Lowe, Photographer, 1989. - U.S. Steel Homestead Works, Blast Furnace Plant, Along Monongahela River, Homestead, Allegheny County, PA

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. A larger image is available without labels (No. 0101755).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD).

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This computer-generated image depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830).

Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 3: Combustors, furnaces and low-BTU gasifiers. [used in coal gasification and coal liquefaction (equipment specifications)

NASA Technical Reports Server (NTRS)

Hamm, J. R.

1976-01-01

Information is presented on the design, performance, operating characteristics, cost, and development status of coal preparation equipment, combustion equipment, furnaces, low-Btu gasification processes, low-temperature carbonization processes, desulfurization processes, and pollution particulate removal equipment. The information was compiled for use by the various cycle concept leaders in determining the performance, capital costs, energy costs, and natural resource requirements of each of their system configurations.

Experiment Requirements and Implementation Plan (ERIP) for semiconductor materials growth in low-G environment experiment no. MPS-77F087

NASA Technical Reports Server (NTRS)

Crouch, R. K.; Fripp, A. L.; Debnam, W. J.; Clark, I. O.

1981-01-01

Crystals of the intermetallic compound Pb1-xSnxTe will be grown in furnaces on the Space Shuttle. The reasons for conducting this growth in space, the program of investigation to develop the space experiment and the requirements that are placed on the Space Shuttle furnace are discussed. Also included are relevent thermophysical properties of Pb1-xSnxTe to the degree which they are known.

Synthesis, and spectroscopic studies of charge transfer complex of 1,2-dimethylimidazole as an electron donor with π-acceptor 2,4-dinitro-1-naphthol in different polar solvents

NASA Astrophysics Data System (ADS)

Miyan, Lal; Khan, Ishaat M.; Ahmad, Afaq

2015-07-01

The charge transfer (CT) complex of 1,2-dimethylimidazole (DMI) as an electron donor with π acceptor 2,4-dinitro-1-naphthol (DNN) has been studied spectrophotometrically in different solvents like chloroform, acetonitrile, methanol, methylene chloride, etc. at room temperature. The CT complex which is formed through the transfer of lone pair electrons from DMI to DNN exhibits well resolved CT bands and the regions of these bands were remarkably different from those of the donor and acceptor. The stoichiometry of the CT complex was found to be 1:1 by a straight-line method between donor and acceptor with maximum absorption bands. The novel CT complex has been characterized by FTIR, TGA-DTA, powder XRD, 1H NMR and 13C NMR spectroscopic techniques. The Benesi-Hildebrand equation has been used to determine the formation constant (KCT), molar extinction coefficient (εCT), standard gibbs free energy (ΔG°) and other physical parameters of the CT complex. The formation constant recorded higher values and molar extinction coefficient recorded lower values in chloroform compared with methylene chloride, methanol and acetonitrile, confirming the strong interaction between the molecular orbital's of donor and acceptor in the ground state in less polar solvent. This CT complex has been studied by absorption spectra of donor 1,2-dimethylimidazole (DMI) and acceptor 2,4-dinitro-1-naphthol (DNN) by using the spectrophotometric technique in various solvents at room temperature.

One-Year Effectiveness of a 3-Week Balneotherapy Program for the Treatment of Overweight or Obesity

PubMed Central

Hanh, Thierry; Serog, Patrick; Fauconnier, Jérôme; Batailler, Pierre; Mercier, Florence; Roques, Christian F.; Blin, Patrick

2012-01-01

Objective. To assess the one-year effectiveness on weight loss of a 3-week balneotherapy program (BT). Method. A Zelen double consent randomised controlled trial to compare one-year BMI loss between a 3-week BT program versus usual care (UC) for overweight or obese patients (BMI: 27–35 kg/m2), associated or not with a dietary motivational interview (DMI) during the follow-up, using a 2 × 2 factorial design. Main analysis was a per protocol analysis comparing patients attending BT to patients managed by UC, matched on sex, overweight or obese status, DMI randomisation and a propensity score to attend BT or to be managed by UC. Results. From the 257 patients who completed the follow-up, 70 patients of each group could be matched. Mean BMI loss was 1.91 kg/m2 [95%CI: 1.46; 2.35] for the BT patients and 0.20 kg/m2 [−0.24; 0.64] for the UC patients (P < 0.001), corresponding to a significant BT benefit of 1.71 kg/m2 [1.08; 2.33]. There was no significant effect of DMI and no interaction with BT or UC. No adverse reaction was observed for patients attending BT. Conclusion. A 3-week BT program provided a significant one-year benefit over the usual GP dietary advice for overweight and obese patients. PMID:23346190

Overexpression of the CYP51A1 Gene and Repeated Elements are Associated with Differential Sensitivity to DMI Fungicides in Venturia inaequalis.

PubMed

Villani, Sara M; Hulvey, Jon; Hily, Jean-Michel; Cox, Kerik D

2016-06-01

The involvement of overexpression of the CYP51A1 gene in Venturia inaequalis was investigated for isolates exhibiting differential sensitivity to the triazole demethylation inhibitor (DMI) fungicides myclobutanil and difenoconazole. Relative expression (RE) of the CYP51A1 gene was significantly greater (P < 0.0001) for isolates with resistance to both fungicides (MRDR phenotype) or with resistance to difenoconazole only (MSDR phenotype) compared with isolates that were resistant only to myclobutanil (MRDS phenotype) or sensitive to both fungicides (MSDS phenotype). An average of 9- and 13-fold increases in CYP51A1 RE were observed in isolates resistant to difenoconazole compared with isolates with MRDS and MSDS phenotypes, respectively. Linear regression analysis between isolate relative growth on myclobutanil-amended medium and log10 RE revealed that little to no variability in sensitivity to myclobutanil could be explained by CYP51A1 overexpression (R(2) = 0.078). To investigate CYP51A1 upstream anomalies associated with CYP51A1 overexpression or resistance to difenoconazole, Illumina sequencing was conducted for three isolates with resistance to difenoconazole and one baseline isolate. A repeated element, "EL 3,1,2", with the properties of a transcriptional enhancer was identified two to four times upstream of CYP51A1 in difenoconazole-resistant isolates but was not found in isolates with the MRDS phenotype. These results suggest that different mechanisms may govern resistance to different DMI fungicides in the triazole group.

Transcriptome Analysis of Arbuscular Mycorrhizal Roots during Development of the Prepenetration Apparatus1[W

PubMed Central

Siciliano, Valeria; Genre, Andrea; Balestrini, Raffaella; Cappellazzo, Gilda; deWit, Pierre J.G.M.; Bonfante, Paola

2007-01-01

Information on changes in the plant transcriptome during early interaction with arbuscular mycorrhizal (AM) fungi is still limited since infections are usually not synchronized and plant markers for early stages of colonization are not yet available. A prepenetration apparatus (PPA), organized in epidermal cells during appressorium development, has been reported to be responsible for assembling a trans-cellular tunnel to accommodate the invading fungus. Here, we used PPAs as markers for cell responsiveness to fungal contact to investigate gene expression at this early stage of infection with minimal transcript dilution. PPAs were identified by confocal microscopy in transformed roots of Medicago truncatula expressing green fluorescent protein-HDEL, colonized by the AM fungus Gigaspora margarita. A PPA-targeted suppressive-subtractive cDNA library was built, the cDNAs were cloned and sequenced, and, consequently, 107 putative interaction-specific genes were identified. The expression of a subset of 15 genes, selected by reverse northern dot blot screening, and five additional genes, potentially involved in PPA formation, was analyzed by real-time reverse transcription-polymerase chain reaction and compared with an infection stage, 48 h after the onset of the PPA. Comparison of the expression profile of G. margarita-inoculated wild type and the mycorrhiza-defective dmi3-1 mutant of M. truncatula revealed that an expansin-like gene, expressed in wild-type epidermis during PPA development, can be regarded as an early host marker for successful mycorrhization. A putative Avr9/Cf-9 rapidly elicited gene, found to be up-regulated in the mutant, suggests novel regulatory roles for the DMI3 protein in the early mycorrhization process. PMID:17468219

Control of carbon balance in a silicon smelting furnace

DOEpatents

Dosaj, Vishu D.; Haines, Cathryn M.; May, James B.; Oleson, John D.

1992-12-29

The present invention is a process for the carbothermic reduction of silicon dioxide to form elemental silicon. Carbon balance of the process is assessed by measuring the amount of carbon monoxide evolved in offgas exiting the furnace. A ratio of the amount of carbon monoxide evolved and the amount of silicon dioxide added to the furnace is determined. Based on this ratio, the carbon balance of the furnace can be determined and carbon feed can be adjusted to maintain the furnace in carbon balance.

Compact low power infrared tube furnace for in situ X-ray powder diffraction

NASA Astrophysics Data System (ADS)

Doran, A.; Schlicker, L.; Beavers, C. M.; Bhat, S.; Bekheet, M. F.; Gurlo, A.

2017-01-01

We describe the development and implementation of a compact, low power, infrared heated tube furnace for in situ powder X-ray diffraction experiments. Our silicon carbide (SiC) based furnace design exhibits outstanding thermal performance in terms of accuracy control and temperature ramping rates while simultaneously being easy to use, robust to abuse and, due to its small size and low power, producing minimal impact on surrounding equipment. Temperatures in air in excess of 1100 °C can be controlled at an accuracy of better than 1%, with temperature ramping rates up to 100 °C/s. The complete "add-in" device, minus power supply, fits in a cylindrical volume approximately 15 cm long and 6 cm in diameter and resides as close as 1 cm from other sensitive components of our experimental synchrotron endstation without adverse effects.

Application of Carbon Composite Bricks for Blast Furnace Hearth

NASA Astrophysics Data System (ADS)

Zuo, Haibin; Wang, Cong; Zhang, Jianliang; Zhao, Yongan; Jiao, Kexin

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can't meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Carbon-free induction furnace

DOEpatents

Holcombe, Cressie E.; Masters, David R.; Pfeiler, William A.

1985-01-01

An induction furnace for melting and casting highly pure metals and alloys such as uranium and uranium alloys in such a manner as to minimize contamination of the melt by carbon derived from the materials and the environment within the furnace. The subject furnace is constructed of carbon free materials and is housed within a conventional vacuum chamber. The furnace comprises a ceramic oxide crucible for holding the charge of metal or alloy. The heating of the crucible is achieved by a plasma-sprayed tungsten susceptor surrounding the crucible which, in turn, is heated by an RF induction coil separated from the susceptor by a cylinder of inorganic insulation. The furnace of the present invention is capable of being rapidly cycled from ambient temperatures to about 1650.degree. C. for effectively melting uranium and uranium alloys without the attendant carbon contamination problems previously encountered when using carbon-bearing furnace materials.

Non-carbon induction furnace

DOEpatents

Holcombe, C.E.; Masters, D.R.; Pfeiler, W.A.

1984-01-06

The present invention is directed to an induction furnace for melting and casting highly pure metals and alloys such as uranium and uranium alloys in such a manner as to minimize contamination of the melt by carbon derived from the materials and the environment within the furnace. The subject furnace is constructed of non-carbon materials and is housed within a conventional vacuum chamber. The furnace comprises a ceramic oxide crucible for holding the charge of metal or alloys. The heating of the crucible is achieved by a plasma-sprayed tungsten susceptor surrounding the crucible which, in turn, is heated by an rf induction coil separated from the susceptor by a cylinder of inorganic insulation. The furnace of the present invention is capable of being rapidly cycled from ambient temperatures to about 1650/sup 0/C for effectively melting uranium and uranium alloys without the attendant carbon contamination problems previously encountered when using carbon-bearing furnace materials.

75 FR 17075 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces and...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-05

... different in mathematical form, is conceptually the same as the integrated AFUE for fossil fueled furnaces... that gas-fired and oil-fried furnaces and boilers consume both fossil fuel and electricity, while electric furnaces and boilers only consume electricity. The current test procedure accounts for all fossil...

75 FR 41102 - Energy Conservation Program: Energy Conservation Standards for Furnace Fans: Reopening of Public...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-15

... Furnace Fans: Reopening of Public Comment Period AGENCY: Office of Energy Efficiency and Renewable Energy... work of residential heating and cooling systems (``furnace fans''). The comment period closed on July 6... information relevant to the furnace fan rulemaking will be accepted until July 27, 2010. ADDRESSES: Interested...

76 FR 61999 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

... for Residential Furnaces and Boilers (Standby Mode and Off Mode); Correction AGENCY: Office of Energy... Consumer Products: Test Procedures for Residential Furnaces and Boilers. This correction provides the... page 56339, in the third column after ``2. E- mail:'' the e-mail address should read `` FurnaceBoiler...

78 FR 53625 - Energy Conservation Program for Consumer Products: Test Procedures for Residential Furnaces and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-30

... Program for Consumer Products: Test Procedures for Residential Furnaces and Boilers; Correction AGENCY... Federal Register that amended the test procedure for residential furnaces and boilers (78 FR 41265). Due...., Washington, DC 20585-0121. Telephone: (202) 586-6590. Email: residential_furnaces_and_boilers@ee.doe.gov . Mr...

46 CFR 59.15-5 - Stayed furnaces and combustion chambers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Stayed furnaces and combustion chambers. 59.15-5 Section... and combustion chambers. (a) Where the plate forming the walls of stayed furnaces or combustion... wall of a stayed furnace or combustion chamber, the defective portion of the plate shall be cut away...

46 CFR 59.15-5 - Stayed furnaces and combustion chambers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Stayed furnaces and combustion chambers. 59.15-5 Section... and combustion chambers. (a) Where the plate forming the walls of stayed furnaces or combustion... wall of a stayed furnace or combustion chamber, the defective portion of the plate shall be cut away...

46 CFR 59.15-5 - Stayed furnaces and combustion chambers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Stayed furnaces and combustion chambers. 59.15-5 Section... and combustion chambers. (a) Where the plate forming the walls of stayed furnaces or combustion... wall of a stayed furnace or combustion chamber, the defective portion of the plate shall be cut away...

46 CFR 59.15-5 - Stayed furnaces and combustion chambers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Stayed furnaces and combustion chambers. 59.15-5 Section... and combustion chambers. (a) Where the plate forming the walls of stayed furnaces or combustion... wall of a stayed furnace or combustion chamber, the defective portion of the plate shall be cut away...

46 CFR 59.15-5 - Stayed furnaces and combustion chambers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Stayed furnaces and combustion chambers. 59.15-5 Section... and combustion chambers. (a) Where the plate forming the walls of stayed furnaces or combustion... wall of a stayed furnace or combustion chamber, the defective portion of the plate shall be cut away...

40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

Code of Federal Regulations, 2011 CFR

2011-07-01

... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control devices...

40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

Code of Federal Regulations, 2010 CFR

2010-07-01

... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control devices...

40 CFR 63.7690 - What emissions limitations must I meet?

Code of Federal Regulations, 2013 CFR

2013-07-01

... metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing iron... electric induction metal melting furnace or scrap preheater at a new iron and steel foundry, you must not... furnace at an existing iron and steel foundry, you must not discharge emissions through a conveyance to...

40 CFR 63.7690 - What emissions limitations must I meet?

Code of Federal Regulations, 2011 CFR

2011-07-01

... metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing iron... electric induction metal melting furnace or scrap preheater at a new iron and steel foundry, you must not... furnace at an existing iron and steel foundry, you must not discharge emissions through a conveyance to...

40 CFR 63.7690 - What emissions limitations must I meet?

Code of Federal Regulations, 2012 CFR

2012-07-01

... metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing iron... electric induction metal melting furnace or scrap preheater at a new iron and steel foundry, you must not... furnace at an existing iron and steel foundry, you must not discharge emissions through a conveyance to...

40 CFR 63.7690 - What emissions limitations must I meet?

Code of Federal Regulations, 2014 CFR

2014-07-01

... metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing iron... electric induction metal melting furnace or scrap preheater at a new iron and steel foundry, you must not... furnace at an existing iron and steel foundry, you must not discharge emissions through a conveyance to...

40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

Code of Federal Regulations, 2013 CFR

2013-07-01

... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control devices...

40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

Code of Federal Regulations, 2014 CFR

2014-07-01

... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control devices...

40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

Code of Federal Regulations, 2012 CFR

2012-07-01

... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control devices...

Heating rates in furnace atomic absorption using the L'vov platform

USGS Publications Warehouse

Koirtyohann, S.R.; Giddings, R.C.; Taylor, Howard E.

1984-01-01

Heating rate profiles for the furnace tube wall, the furnace atmosphere, and a L'vov platform were established for a range of conditions in a cyclically heated graphite atomizer. The tube wall profile was made by direct observation with a recording optical pyrometer. The sodium line reversal method was used to establish the heating rate of the furnace atmosphere, and appearance temperatures for a series metals of differing volatility was used to establish platform profiles. The tube wall heating rate was nearly linear at 2240??C s- until the desired temperature was reached after which the temperature remained constant. The furnace atmosphere reached a given temperature 0.2-0.4 s later than the tube wall through most of the atomize cycle. The platform lagged the tube wall 0.5-0.8 s. Under typical operating conditions the furnace atmosphere was 100-200??C cooler than the tube wall and at nearly constant temperature when the analyte vaporized from the platform. The L'vov platform causes the cyclically heated commercial furnace to approximate the behavior of a constant temperature furnace during atomization. ?? 1984.

BPM Motors in Residential Gas Furnaces: What are theSavings?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutz, James; Franco, Victor; Lekov, Alex

2006-05-12

Residential gas furnaces contain blowers to distribute warm air. Currently, furnace blowers use either a Permanent Split Capacitor (PSC) or a Brushless Permanent Magnet (BPM) motor. Blowers account for the majority of furnace electricity consumption. Therefore, accurate determination of the blower electricity consumption is important for understanding electricity consumption of furnaces. The electricity consumption of blower motors depends on the static pressure across the blower. This paper examines both types of blower motors in non-condensing non-weatherized gas furnaces at a range of static pressures. Fan performance data is based on manufacturer product literature and laboratory tests. We use field-measured staticmore » pressure in ducts to get typical system curves to calculate how furnaces would operate in the field. We contrast this with the electricity consumption of a furnace blower operating under the DOE test procedure and manufacturer rated conditions. Furnace electricity use is also affected by operating modes that happen at the beginning and end of each furnace firing cycle. These operating modes are the pre-purge and post-purge by the draft inducer, the on-delay and off-delay of the blower, and the hot surface ignitor operation. To accurately calculate this effect, we use the number of firing cycles in a typical California house in the Central Valley of California. Cooling hours are not considered in the DOE test procedure. We also account for furnace blower use by the air conditioner and stand-by power. Overall BPM motors outperform PSC motors, but the total electricity savings are significantly less than projected using the DOE test procedure conditions. The performance gains depend on the static pressure of the household ducts, which are typically much higher than in the test procedures.« less

Polycyclic aromatic hydrocarbon and particulate emissions from two-stage combustion of polystyrene: the effect of the primary furnace temperature.

PubMed

Wang, J; Levendis, Y A; Richter, H; Howard, J B; Carlson, J

2001-09-01

A study is presented on laboratory-scale combustion of polystyrene (PS) to identify staged-combustion conditions that minimize emissions. Batch combustion of shredded PS was conducted in fixed beds placed in a bench-scale electrically heated horizontal muffle furnace. In most cases, combustion of the samples occurred by forming gaseous diffusion flames in atmospheric pressure air. The combustion effluent was mixed with additional air, and it was channeled to a second muffle furnace (afterburner) placed in series. Further reactions took place in the secondary furnace at a residence time of 0.7 s. The gas temperature of the primary furnace was varied in the range of 500-1,000 degrees C, while that of the secondary furnace was kept fixed at 1,000 degrees C. Sampling for CO, CO2, O2, soot, and unburned hydrocarbon emissions (volatile and semivolatile, by GC-MS) was performed at the exits of the two furnaces. Results showed that the temperature of the primary furnace, where PS gasifies, is of paramount importance to the formation and subsequent emissions of organic species and soot. Atthe lowesttemperatures explored, mostly styrene oligomers were identified at the outlet of the primary furnace, but they did not survive the treatment in the secondary furnace. The formation and emission of polycyclic aromatic hydrocarbons (PAH) and soot were suppressed. As the temperature in the first furnace was raised, increasing amounts of a wide range of both unsubstituted and substituted PAH containing up to at least seven condensed aromatic rings were detected. A similar trend was observed for total particulate yields. The secondary furnace treatment reduced the yields of total PAH, but it had an ambiguous effect on individual species. While most low molecular mass PAH were reduced in the secondary furnace, concentrations of some larger PAH increased under certain conditions. Thus, care in the selection of operating conditions of both the primary furnace (gasifier/ burner) and the secondary furnace (afterburner) must be exercised to minimize the emission of hazardous pollutants. The emissions of soot were also reduced in the afterburner but not drastically. This indicates that soot is indeed resistant to oxidation; thus, it would be best to avoid its formation in the first place. An oxidative pyrolysis temperature of PS in the vicinity of 600 degrees C appears to accomplish exactly that. An additional afterburner treatment at a sufficiently high temperature (1,000 degrees C) may be a suitable setting for minimization of most pollutants. To obtain deeper understanding of chemical processes, the experimental results were qualitatively compared with preliminary predictions of a detailed kinetic model that describes formation and destruction pathways of chemical species including most PAH observed in the present work. The modeling was performed forthe secondary furnace assuming plug-flow conditions therein. The experimentally determined chemical composition at the outlet of the primary furnace was part of the input parameters of the model calculation.

The role of exogenous insulin in the complex of hepatic lipidosis and ketosis associated with insulin resistance phenomenon in postpartum dairy cattle.

PubMed

Hayirli, A

2006-10-01

As a result of a marked decline in dry matter intake (DMI) prior to parturition and a slow rate of increase in DMI relative to milk production after parturition, dairy cattle experience a negative energy balance. Changes in nutritional and metabolic status during the periparturient period predispose dairy cattle to develop hepatic lipidosis and ketosis. The metabolic profile during early lactation includes low concentrations of serum insulin, plasma glucose, and liver glycogen and high concentrations of serum glucagon, adrenaline, growth hormone, plasma beta-hydroxybutyrate and non-esterified fatty acids, and liver triglyceride. Moreover, during late gestation and early lactation, flow of nutrients to fetus and mammary tissues are accorded a high degree of metabolic priority. This priority coincides with lowered responsiveness and sensitivity of extrahepatic tissues to insulin, which presumably plays a key role in development of hepatic lipidosis and ketosis. Hepatic lipidosis and ketosis compromise production, immune function, and fertility. Cows with hepatic lipidosis and ketosis have low tissue responsiveness to insulin owing to ketoacidosis. Insulin has numerous roles in metabolism of carbohydrates, lipids and proteins. Insulin is an anabolic hormone and acts to preserve nutrients as well as being a potent feed intake regulator. In addition to the major replacement therapy to alleviate severity of negative energy balance, administration of insulin with concomitant delivery of dextrose increases efficiency of treatment for hepatic lipidosis and ketosis. However, data on use of insulin to prevent these lipid-related metabolic disorders are limited and it should be investigated.

Monte Carlo simulation of electrothermal atomization on a desktop personal computer

NASA Astrophysics Data System (ADS)

Histen, Timothy E.; Güell, Oscar A.; Chavez, Iris A.; Holcombea, James A.

1996-07-01

Monte Carlo simulations have been applied to electrothermal atomization (ETA) using a tubular atomizer (e.g. graphite furnace) because of the complexity in the geometry, heating, molecular interactions, etc. The intense computational time needed to accurately model ETA often limited its effective implementation to the use of supercomputers. However, with the advent of more powerful desktop processors, this is no longer the case. A C-based program has been developed and can be used under Windows TM or DOS. With this program, basic parameters such as furnace dimensions, sample placement, furnace heating and kinetic parameters such as activation energies for desorption and adsorption can be varied to show the absorbance profile dependence on these parameters. Even data such as time-dependent spatial distribution of analyte inside the furnace can be collected. The DOS version also permits input of external temperaturetime data to permit comparison of simulated profiles with experimentally obtained absorbance data. The run-time versions are provided along with the source code. This article is an electronic publication in Spectrochimica Acta Electronica (SAE), the electronic section of Spectrochimica Acta Part B (SAB). The hardcopy text is accompanied by a diskette with a program (PC format), data files and text files.

Ultra-high temperature isothermal furnace liners (IFLS) for copper freeze point cells

NASA Astrophysics Data System (ADS)

Dussinger, P. M.; Tavener, J. P.

2013-09-01

Primary Laboratories use large fixed-point cells in deep calibration furnaces utilizing heat pipes to achieve temperature uniformity. This combination of furnace, heat pipe, and cell gives the smallest of uncertainties. The heat pipe, also known as an isothermal furnace liner (IFL), has typically been manufactured with Alloy 600/601 as the envelope material since the introduction of high temperature IFLs over 40 years ago. Alloy 600/601 is a widely available high temperature material, which is compatible with Cesium, Potassium, and Sodium and has adequate oxidation resistance and reasonable high temperature strength. Advanced Cooling Technologies, Inc. (ACT) Alloy 600/Sodium IFLs are rated to 1100°C for approximately 1000 hours of operation (based on creep strength). Laboratories interested in performing calibrations and studies around the copper freezing point (1084.62°C) were frustrated by the 1000 hours at 1100°C limitation and the fact that expensive freeze-point cells were getting stuck and/or crushed inside the IFL. Because of this growing frustration/need, ACT developed an Ultra High Temperature IFL to take advantage of the exceptional high temperature strength properties of Haynes 230.

Furnace Cyclic Behavior of Plasma-Sprayed Zirconia-Yttria and Multi-Component Rare Earth Oxide Doped Thermal Barrier Coatings

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Nesbitt, James A.; McCue, Terry R.; Barrett, Charles A.; Miller, Robert A.

2002-01-01

Ceramic thermal barrier coatings will play an increasingly important role in advanced gas turbine engines because of their ability to enable further increases in engine temperatures. However, the coating performance and durability become a major concern under the increasingly harsh thermal cycling conditions. Advanced zirconia- and hafnia-based cluster oxide thermal barrier coatings with lower thermal conductivity and improved thermal stability are being developed using a high-heat-flux laser-rig based test approach. Although the new composition coatings were not yet optimized for cyclic durability, an initial durability screening of numerous candidate coating materials was carried out using conventional furnace cyclic tests. In this paper, furnace thermal cyclic behavior of the advanced plasma-sprayed zirconia-yttria-based thermal barrier coatings that were co-doped with multi-component rare earth oxides was investigated at 1163 C using 45 min hot cycles. The ceramic coating failure mechanisms were studied by using scanning electron microscopy combined with X-ray diffraction phase analysis after the furnace tests. The coating cyclic lifetime will be discussed in relation to coating phase structures, total dopant concentrations, and other properties.

Electrode Arrangement As Substitute Bottom For An Electrothermic Slag Smelting Furnace.

DOEpatents

Aune, Jan Arthur; Brinch, Jon Christian; Johansen, Kai

2005-12-27

The electrode arrangement uses vertically oriented electrodes with side wall contacts for an electrothermic smelting furnace for aluminum production. The side wall contacts are radially moveable into the furnace to compensate for wear on the contacts. The side wall contacts can be hollow to allow a slag forming charge to be fed to the furnace.

29. Blast furnace plant, looking southeast. The Machine Shop and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. Blast furnace plant, looking southeast. The Machine Shop and Turbo Blower Building are at left, the pig-casting machine and Furnace A at center right. In foregound are the 50-ton ladle cars used to transport hot metal to Valley Mould & Iron Co. - Central Furnaces, 2650 Broadway, east bank of Cuyahoga River, Cleveland, Cuyahoga County, OH

INTERIOR VIEW SHOWING QBOP FURNACE IN BLOW. OXYGEN AND NATURAL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW SHOWING Q-BOP FURNACE IN BLOW. OXYGEN AND NATURAL GAS ARE BLOWN INTO THE FURNACE THROUGH THE TUYERES TO CHARGE 460,000 LBS. OF HOT METAL, 100,000 LBS. OF SCRAP WITH 30,000 LBS. OF LIME. BLOW TIME IS 16 MINUTES. THE TIME TO BLOW AND TAP THE FURNACES OF THE RESULTING 205,000 TONS OF STEEL AND SLAG IS 35 MINUTES. - U.S. Steel, Fairfield Works, Q-Bop Furnace, North of Valley Road & West of Ensley, Pleasant Grove Road, Fairfield, Jefferson County, AL

A multi-zone muffle furnace design

NASA Technical Reports Server (NTRS)

Rowe, Neil D.; Kisel, Martin

1993-01-01

A Multi-Zone Muffle-Tube Furnace was designed, built, and tested for the purpose of providing an in-house experience base with tubular furnaces for materials processing in microgravity. As such, it must not only provide the desired temperatures and controlled thermal gradients at several discrete zones along its length but must also be capable of sustaining the rigors of a Space Shuttle launch. The furnace is insulated to minimize radial and axial heat losses. It is contained in a water-cooled enclosure for purposes of dissipating un-wanted residual heat, keeping the outer surfaces of the furnace at a 'touch-safe' temperature, and providing a rugged housing. This report describes the salient features of the furnace, testing procedures and results, and concluding remarks evaluating the overall design.

28. RW Sugar Mill: 18761889. Boilingrange Furnace and Clarifier position. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

28. RW Sugar Mill: 1876-1889. Boiling-range Furnace and Clarifier position. View: In the boiling range all of the clarification, evaporation, and concentration of cane juice took place in open pans over the Continuous flue leading from this furnace. The furnace door through the exterior wall is at the end of the furnace. In the original installation, two copper clarifiers, manufactured by John Nott & Co. occupied this space directly above the furnace. In the clarifiers, lime was added to the cane juice so that impurities would coagulate into a scum on top of the near-boiling juice. The clarifiers have been removed since the closing of the mill. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

29. RW Meyer Sugar Mill: 18761889. Boilingrange furnace and clarifier ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

29. RW Meyer Sugar Mill: 1876-1889. Boiling-range furnace and clarifier position. View: In the boiling range all of the concentration, evaporation, and concentration of cane juice took place in open pans over the continous flue leaving this furnace. The furnace door through the exterior wall is at the end of the furnace. In the original installation two copper clarifiers, manufactured by John Nott & Co. occupied this space directly above the furnace. In the clarifier lime was added to the cane juice so that impurities would coagulate into a scum on top of the near-boiling juice. The clarifiers have been removed since the closing of the mill. - R. W. Meyer Sugar Mill, State Route 47, Kualapuu, Maui County, HI

Project Description and Publications List for UAH CMMR

NASA Technical Reports Server (NTRS)

Kaukler, William F.

1999-01-01

This research combines a state of the art X-ray Transmission Microscope, XTM, with a specially designed x-ray transparent horizontal Bridgman furnace to image (with resolutions up to 3 micrometers) the solidification of metal alloys in real-time. The objective is to obtain real-time dynamic data to provide direct measure of the solute profile in the liquid, phase coalescence and growth in the liquid, and the detailed interface morphology (e,g., dendrites and cells) during solidification. We are also enhancing the XTM data with precise solid-liquid interfacial temperature and the thermal gradient measurement techniques, and working on the application of this technology to the study of the fundamentals of solidification in microgravity. Over the last several years we have successfully imaged in real-time: interfacial-morphologies, phase growth, coalescence, incorporation of phases into the growing interface, and the solute boundary layer in the liquid at the solid-liquid interface. We have also measured true local growth rates and can evaluate segregation structures in the solid. Interfacial undercoolings are being measured either with a special Seebeck furnace or with micro-thermocouple arrays we are developing. These later techniques are presently being incorporated with the XTM furnace. This last year emphasized the investigation of the solute layer in the melt during solidification. Methods were developed to quantify the solute concentrations using x-ray absorption and to compare to predictions from simulations. In addition, work is being completed on a brass-board portable XTM that incorporates a vertical Bridgman furnace.

Lowering rumen-degradable protein maintained energy-corrected milk yield and improved nitrogen-use efficiency in multiparous lactating dairy cows exposed to heat stress.

PubMed

Kaufman, J D; Kassube, K R; Ríus, A G

2017-10-01

The objective of this study was to examine the effect of reducing rumen-degradable protein (RDP) and rumen-undegradable protein (RUP) proportions on feed intake, milk production, and N-use efficiency in primiparous and multiparous cows exposed to warm climates. Eighteen primiparous and 30 multiparous mid-lactation Holstein cows were used in a completely randomized design with a 2 × 2 factorial arrangement of treatments. Cows were randomly assigned to 1 of 4 dietary treatments formulated to contain 2 proportions of RDP (10 and 8%) and 2 proportions RUP (8 and 6%) of dry matter (DM) indicated as follows: (1) 10% RDP, 8% RUP; (2) 8% RDP, 8% RUP; (3) 10% RDP, 6% RUP; and (4) 8% RDP, 6% RUP. Protein sources were manipulated to obtain desired RDP and RUP proportions. Diets were isoenergetic and contained 50% forage and 50% concentrate (DM basis). Cows were individually fed the 10% RDP, 8% RUP diet 3 wk before treatment allocation. Cows were exposed to the prevailing Tennessee July and August temperature and humidity in a freestall barn with no supplemental cooling. Main effects and their interaction were tested using the Mixed procedure of SAS (least squares means ± standard error of the mean; SAS Institute Inc., Cary, NC). Observed values of nutrient intake and milk production were used to obtain NRC (2001) model predictions. Cows showed signs of heat stress throughout the study. Reducing from 10 to 8% RDP decreased dry matter intake (DMI; 0.9 kg/d) at 8% RUP, but increased DMI (2.6 kg/d) at 6% RUP in primiparous cows. Reducing from 10 to 8% RDP decreased milk yield (10%) at 8% RUP, but increased yield (14%) at 6% RUP. Treatments did not affect yield of energy-corrected milk. For multiparous cows, treatments did not affect DMI. Reducing from 10 to 8% RDP decreased yield of energy-corrected milk (3.4%) at 8% RUP, but increased yield (8.8%) at 6% RUP. Reducing from 10 to 8% RDP and 8 to 6% RUP both increased N-use efficiency for primiparous and multiparous cows. The NRC model underestimated metabolizable protein and RUP supply, and overestimated RUP requirements, resulting in predictive losses of milk yield 1.4 to 5.8 times greater than observed values. In summary, the reduction of RDP and RUP proportions did not affect DMI, whereas the RUP reduction at 10% RDP had a small negative effect on energy-corrected milk yield. However, reduction of RDP and RUP consistently improved N-use efficiency of heat-stressed multiparous cows. The reduction of RDP and RUP proportions reduced DMI and milk yield but did not affect energy-corrected milk yield in primiparous cows, indicating a limited supply of nutrients. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Jersey calf performance in response to high-protein, high-fat liquid feeds with varied fatty acid profiles: intake and performance.

PubMed

Bowen Yoho, W S; Swank, V A; Eastridge, M L; O'Diam, K M; Daniels, K M

2013-04-01

The objective of this study was to determine whether altering the fatty acid (FA) profile of milk replacer (MR) with coconut oil, which contains a high concentration of medium-chain FA, to more closely match the FA profile typically found in whole milk from Jersey cows, would improve Jersey calf performance. Male (n=18) and female (n=32) Jersey calves were assigned at birth to 1 of 4 liquid diets: (1) pasteurized Jersey saleable whole milk [pSWM; 27.9% crude protein (CP) and 33.5% fat]; (2) 29.3% CP and 29.1% fat MR, containing 100% of fat as edible lard (100:00); (3) 28.2% CP and 28.0% fat MR, containing 80% of fat as lard and 20% as coconut oil (80:20); and (4) 28.2% CP and 28.3% fat MR, containing 60% of the fat as lard and 40% as coconut oil (60:40). Calves were fed their respective liquid diet twice daily during wk 1 through 7 and once daily until weaning (approximately wk 8). Calves had ad libitum access to grain and water, and calves were monitored 1 wk postweaning. Average daily gain and body weight did not differ by treatment. Calves fed pSWM tended to have greater hip height (HH) than calves fed 80:20 (80.5 vs. 79.7 cm). Coconut oil tended to have a quadratic effect on HH, with calves fed 100:00, 80:20, and 60:40 at 79.2, 79.7, and 78.5 cm, respectively. No difference was observed in withers height between pSWM and 80:20. Coconut oil had a quadratic effect on withers height, with calves fed 100:00, 80:20, and 60:40 at 76.6, 77.5, and 76.5 cm, respectively. Change in HH from birth to 9 wk tended to be greater for calves fed pSWM than calves fed 80:20 (0.218 vs. 0.194 cm/d). Calves fed pSWM had higher milk dry matter intake (DMI) than calves fed 80:20 (0.580 vs. 0.518 kg/d). No effect of coconut oil was observed on milk DMI. Grain DMI and total DMI did not differ among treatments. Calves fed pSWM had an increase in days with a fecal score >2 compared with calves fed 80:20 (4.24 vs. 2.00 d). Coconut oil had a quadratic effect on fecal score, with calves fed 100:00, 80:20, and 60:40 scoring 4.00, 2.00, and 3.63 d, respectively. Respiratory score did not differ among treatments. In conclusion, DMI and average daily gain were similar among treatments. However, differences among treatments in skeletal growth and fecal scores are indicative of some possible benefits of medium-chain FA on calf health and performance. Copyright © 2013 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Effects of residual feed intake classification and method of alfalfa processing on ewe intake and growth.

PubMed

Redden, R R; Surber, L M M; Grove, A V; Kott, R W

2014-02-01

The objective of this research was to evaluate the effects of residual feed intake (RFI) determined under ad libitum feeding conditions on DMI and performance of yearling ewes fed either chopped or pelleted alfalfa hay. In Exp. 1, 45 ewe-lambs had ad libitum access to a pelleted grower diet for 63 d and individual DMI was determined using an electronic feed delivery system. Residual feed intake values were assigned to each ewe-lamb as a measure of feed efficiency. Sixteen ewe-lambs with the most positive RFI values were classified as high RFI (inefficient) and 16 ewe-lambs with the most negative RFI values were classified as low RFI (efficient). In Exp. 2, half of the ewes from each efficiency group were placed into 1 of 2 pens and provided ad libitum access to either pelleted or chopped alfalfa hay. Individual DMI was again determined using an electronic feed delivery system. Body weight, LM area (LMA), and 12th-rib back fat thickness (BF) were measured at the beginning and end of both experiments. In Exp. 1, DMI by ewe-lambs in the low RFI group was 9% less (P = 0.01) than by ewe-lambs in the high RFI group (2.21 vs. 2.43 kg/d); however, ADG and initial and final BW, LMA, and BF did not differ (P > 0.27) among RFI groups. In Exp. 2, there were no feed processing × RFI group interactions (P > 0.14) for any trait. By design, RFI values were lower (P < 0.01) by yearling ewes in the low than high RFI group (-0.27 vs. 0.27); however, RFI values did not differ (P = 1.0) between yearling ewes fed chopped versus pelleted alfalfa. Dry matter intake was 22% less (P < 0.01) by yearling ewes in the low than high RFI group (2.5 vs. 3.2 kg/d) and 59% less (P < 0.01) by yearling ewes fed chopped versus pelleted alfalfa (2.2 vs. 3.5 kg/d). Initial and final BW, ADG, and G:F did not differ (P > 0.45) between RFI groups but were greater (P < 0.01) by yearling ewes fed pelleted alfalfa compared to chopped alfalfa. Final LMA did not differ (P = 0.77) between RFI groups, but final BF tended to be greater (P = 0.06) for high than low RFI yearling ewes (0.63 vs. 0.57 cm). Final LMA and BF were greater (P < 0.01) by yearling ewes fed pelleted than chopped alfalfa. Low RFI ewes had lower DMI and BF compared to high RFI ewes. Ewe efficiency as determined by RFI was repeatable on subsequent forage based diets; however, differences in intake and efficiency were more apparent when alfalfa was pelleted.

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD). This image is from a digital still camera; higher resolution is not available.

Microgravity

NASA Image and Video Library

2001-06-05

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, and TBD). This composite is from a digital still camera; higher resolution is not available.

Microgravity

NASA Image and Video Library

2001-06-05

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, 0101830, and TBD). This image is from a digital still camera; higher resolution is not available.

Materials Science Research Rack-1 (MSRR-1)

NASA Technical Reports Server (NTRS)

2001-01-01

This scale model depicts the Materials Science Research Rack-1 (MSRR-1) being developed by NASA's Marshall Space Flight Center and the European Space Agency (ESA) for placement in the Destiny laboratory module aboard the International Space Station. The rack is part of the plarned Materials Science Research Facility (MSRF) and is expected to include two furnace module inserts, a Quench Module Insert (being developed by NASA's Marshall Space Flight Center) to study directional solidification in rapidly cooled alloys and a Diffusion Module Insert (being developed by the European Space Agency) to study crystal growth, and a transparent furnace (being developed by NASA's Space Product Development program). Multi-user equipment in the rack is being developed under the auspices of NASA's Office of Biological and Physical Research (OBPR) and ESA. Key elements are labeled in other images (0101754, 0101829, and TBD). This composite is from a digital still camera; higher resolution is not available.

Trace metals related to historical iron smelting at Hopewell Furnace National Historic Site, Berks and Chester Counties, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.

2011-01-01

Iron ore containing elevated concentrations of trace metals was smelted at Hopewell Furnace during its 113 years of operation (1771-1883). The ore used at Hopewell Furnace was obtained from iron mines within 5 miles of the furnace. The iron-ore deposits were formed about 200 million years ago and contain abundant magnetite, the primary iron mineral, and accessory minerals enriched in arsenic, cobalt, copper, lead, and other metals. Hopewell Furnace, built by Mark Bird during 1770-71, was one of the last of the charcoal-burning, cold-blast iron furnaces operated in Pennsylvania. The most productive years for Hopewell Furnace were from 1830 to 1837. Castings were the most profitable product, especially the popular Hopewell Stove. More than 80,000 stoves were cast at Hopewell, which produced as many as 23 types and sizes of cooking and heating stoves. Beginning in the 1840s, the iron industry shifted to large-scale, steam-driven coke and anthracite furnaces. Independent rural enterprises like Hopewell could no longer compete when the iron and steel industries consolidated in urban manufacturing centers. The furnace ceased operation in 1883 (Kurjack, 1954). The U.S. Geological Survey (USGS), in cooperation with the National Park Service, completed a study at Hopewell Furnace National Historic Site (NHS) in Berks and Chester Counties, Pennsylvania, to determine the fate of toxic trace metals, such as arsenic, cobalt, and lead, released into the environment during historical iron-smelting operations. The results of the study, conducted during 2008-10, are presented in this fact sheet.

Refractory of Furnaces to Reduce Environmental Impact

NASA Astrophysics Data System (ADS)

Hanzawa, Shigeru

2011-10-01

The energy load of furnaces used in the manufacturing process of ceramics is quite large. Most of the environmental impact of ceramics manufacturing is due to the CO2 produced from this high energy load. To improve this situation, R&D has focused on furnace systems and techniques of control in order to reduce energy load. Since furnaces are comprised of refractory, consideration of their mechanical and thermal characteristics is important. Herein are described several refractory types which were chosen through comparison of the characteristics which contribute to heat capacity reduction, heat insulating reinforcement and high emissivity, thereby improving thermal radiation heat transfer efficiency to the ceramic articles. One selected refractory material which will reduce the environmental impact of a furnace, chosen considering low heat capacity and high emissivity characteristics, is SiC. In this study, thermal radiation heat transfer efficiency improvement and its effect on ceramic articles in the furnace and oxidation behaviour were investigated at 1700K. A high density SiC refractory, built into the furnace at construction, has relatively high oxidation durability and has the ability to reduce environmental impact-CO2 by 10 percent by decreasing the furnace's energy load. However, new oxidation prevention techniques for SiC will be necessary for long-term use in industrial furnaces, because passive to active oxidation transition behaviour of commercial SiC refractory is coming to close ideal.

Real-Time Measurements and Characterization of Airborne Particulate Matter from a Primary Silicon Carbide Production Plant.

PubMed

Jørgensen, Rikke Bramming; Kero, Ida Teresia

2017-12-20

Airborne particulate matter in the silicon carbide (SiC) industry is a known health hazard. The aims of this study were to elucidate whether the particulate matter generated inside the Acheson furnace during active operation is representative of the overall particulate matter in the furnace hall, and whether the Acheson furnaces are the main sources of ultrafine particles (UFP) in primary SiC production. The number concentration of ultrafine particles was evaluated using an Electrical Low Pressure Impactor (ELPI TM , Dekati Ltd., Tampere, Finland), a Fast Mobility Particle Sizer (FMPS TM , TSI, Shoreview, MN, USA) and a Condensation Particle Counter (CPC, TSI, Shoreview, MN, USA). The results are discussed in terms of particle number concentration, particle size distribution and are also characterized by means of electron microscopy (TEM/SEM). Two locations were investigated; the industrial Acheson process furnace hall and a pilot furnace hall; both of which represent an active operating furnace. The geometric mean of the particle number concentration in the Acheson process furnace hall was 7.7 × 10⁴ particles/cm³ for the UFP fraction and 1.0 × 10⁵ particles/cm³ for the submicrometre fraction. Particulate matter collected at the two sites was analysed by electron microscopy. The PM from the Acheson process furnace hall is dominated by carbonaceous particles while the samples collected near the pilot furnace are primarily rich in silicon.

Real-Time Measurements and Characterization of Airborne Particulate Matter from a Primary Silicon Carbide Production Plant

PubMed Central

2017-01-01

Airborne particulate matter in the silicon carbide (SiC) industry is a known health hazard. The aims of this study were to elucidate whether the particulate matter generated inside the Acheson furnace during active operation is representative of the overall particulate matter in the furnace hall, and whether the Acheson furnaces are the main sources of ultrafine particles (UFP) in primary SiC production. The number concentration of ultrafine particles was evaluated using an Electrical Low Pressure Impactor (ELPITM, Dekati Ltd., Tampere, Finland), a Fast Mobility Particle Sizer (FMPSTM, TSI, Shoreview, MN, USA) and a Condensation Particle Counter (CPC, TSI, Shoreview, MN, USA). The results are discussed in terms of particle number concentration, particle size distribution and are also characterized by means of electron microscopy (TEM/SEM). Two locations were investigated; the industrial Acheson process furnace hall and a pilot furnace hall; both of which represent an active operating furnace. The geometric mean of the particle number concentration in the Acheson process furnace hall was 7.7 × 104 particles/cm3 for the UFP fraction and 1.0 × 105 particles/cm3 for the submicrometre fraction. Particulate matter collected at the two sites was analysed by electron microscopy. The PM from the Acheson process furnace hall is dominated by carbonaceous particles while the samples collected near the pilot furnace are primarily rich in silicon. PMID:29261158

40 CFR Table 3 to Subpart Rrr of... - Summary of Monitoring Requirements for New and Existing Affected Sources and Emission Units

Code of Federal Regulations, 2010 CFR

2010-07-01

.... Group 1 furnace without add-on controls Fluxing in sidewell furnace hearth Maintain flux addition... emission units with an add-on air pollution control device Emission capture and collection system Annual... specifications, or at least once every 6 months. Group 1 furnace, group 2 furnace, in-line fluxer, and scrap...

40 CFR Table 3 to Subpart Rrr of... - Summary of Monitoring Requirements for New and Existing Affected Sources and Emission Units

Code of Federal Regulations, 2014 CFR

2014-07-01

...; certify every 6 months. Group 1 furnace without add-on controls Fluxing in sidewell furnace hearth... sources and emission units with an add-on air pollution control device Emission capture and collection... to manufacturers specifications, or at least once every 6 months. Group 1 furnace, group 2 furnace...

40 CFR 63.7743 - How do I demonstrate continuous compliance with the emissions limitations that apply to me?

Code of Federal Regulations, 2013 CFR

2013-07-01

... arc metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing... induction metal melting furnace or scrap preheater at a new iron and steel foundry, (i) Maintaining the... at or below 0.0004 gr/dscf. (2) For each cupola metal melting furnace at an existing iron and steel...

40 CFR 63.7743 - How do I demonstrate continuous compliance with the emissions limitations that apply to me?

Code of Federal Regulations, 2012 CFR

2012-07-01

... arc metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing... induction metal melting furnace or scrap preheater at a new iron and steel foundry, (i) Maintaining the... at or below 0.0004 gr/dscf. (2) For each cupola metal melting furnace at an existing iron and steel...

40 CFR 63.7743 - How do I demonstrate continuous compliance with the emissions limitations that apply to me?

Code of Federal Regulations, 2014 CFR

2014-07-01

... arc metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing... induction metal melting furnace or scrap preheater at a new iron and steel foundry, (i) Maintaining the... at or below 0.0004 gr/dscf. (2) For each cupola metal melting furnace at an existing iron and steel...

40 CFR 63.7743 - How do I demonstrate continuous compliance with the emissions limitations that apply to me?

Code of Federal Regulations, 2011 CFR

2011-07-01

... arc metal melting furnace, electric induction metal melting furnace, or scrap preheater at an existing... induction metal melting furnace or scrap preheater at a new iron and steel foundry, (i) Maintaining the... at or below 0.0004 gr/dscf. (2) For each cupola metal melting furnace at an existing iron and steel...